Kilowatt Counter: A Consumer's Guide to Energy Concepts, Quantities, and Uses.

ERIC Educational Resources Information Center

Friend, Gil; Morris, David

This booklet is a basic introduction to energy and energy usage. The first chapter discusses various forms of energy and how they are measured and converted from one to another with a unit conversion chart included. Tables and figures list annual energy requirements of household electrical appliances and energy requirements for houses with various…

Biomass: An Alternative Source of Energy for Eighth or Ninth Grade Science.

ERIC Educational Resources Information Center

Heyward, Lillie; Murff, Marye

This teaching unit develops the possibility of using biomass as an alternative source of energy. The concept of biomass is explained and the processes associated with its conversion to energy are stated. Suggestions for development of biomass technology in different geographic areas are indicated. Lessons for 6 days are presented for use with…

Advanced direct coal liquefaction concepts. Quarterly report, January 1, 1993--March 31, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

1993-07-01

Five barrels of a Wilsonville process derived solvent (V-1074) from Black Thunder coal were obtained. This material boils within the preferred gas oil range, is more aromatic than previous solvents, and will therefore be used for the bench unit studies. Several repeat runs were performed in the autoclave to confirm the results of the matrix study. In addition, runs were carried out with different catalysts, with agglomerates and with the V-1074 solvent. The results of the autoclave runs were analyzed with respect to coal conversion, CO conversion, oil yield, hydrogen consumption and oxygen removal. It was concluded that the bestmore » operating conditions for the first stage operation was a temperature of at least 390{degrees}C, residence time of at least 30 minutes, cold CO pressure of at least 600 psig and potassium carbonate catalyst (2% wt on total feed). The data also indicated however, that the coal conversion goes through a maximum, and too high a severity leads to retrograde reaction and lower coal solubilization. The scope for increasing temperature and time is therefore limited. Petrographic examination of the THF insoluble resids from the autoclave program indicated a maximum coal conversion of about 90% for Black Thunder coal. The bench unit construction was also essentially completed and the bench unit program to be carded out in the next twelve months was defined.« less

Comparative performance of solar thermal power generation concepts

NASA Technical Reports Server (NTRS)

Wen, L.; Wu, Y. C.

1976-01-01

A performance comparison is made between the central receiver system (power tower) and a distributed system using either dishes or troughs and lines to transport fluids to the power station. These systems were analyzed at a rated capacity of 30 MW of thermal energy delivered in the form of superheated steam at 538 C (1000 F) and 68 atm (1000 psia), using consistent weather data, collector surface waviness, pointing error, and electric conversion efficiency. The comparisons include technical considerations for component requirements, land utilization, and annual thermal energy collection rates. The relative merits of different representative systems are dependent upon the overall conversion as expressed in the form of performance factors in this paper. These factors are essentially indices of the relative performance effectiveness for different concepts based upon unit collector area. These performance factors enable further economic tradeoff studies of systems to be made by comparing them with projected production costs for these systems.

Mini-BRU/BIPS 1300 watt (sub)e dynamic power conversion system development: Executive summary

NASA Technical Reports Server (NTRS)

1978-01-01

The status of the Brayton Isotope Power System (BIPS) is summarized. A 1200 watt sub e ground development unit was built and tested in a 0.000010 torr vacuum environment. Peformance mapping and 1000 hours of proof of concept system testing were completed. Specific components, primarily turbocompressor/alternator and recuperator performed according to predictions, thus achieving the design goal of 25 percent net power conversion efficiency. The system was fabricated from superalloy (Hastelloy-X and Waspaloy) thus placing it entirely within current state-of-the-art technology. The system could be flyable in the early 1980's pending flight qualification.

A-Gendering Skill. Conversations around Women, Work and Skill: An Australian Perspective. EEE703 Project Development Plan 2.

ERIC Educational Resources Information Center

Butler, Elaine, Ed.; Brown, Mike, Ed.

These 12 papers are part of the study materials for the one-semester distance education unit, Project Development Plan 2, in the Open Campus Program at Deakin University (Australia). They examine the breadth and depth of the actions and debates around the social construction of skill and the critical role played by the concept of skill in the…

Rayleigh, the unit for light radiance.

PubMed

Baker, D J

1974-09-01

A 0.7% accurate formula is derived for the easy conversion of power spectral radiance L(lambda) in W cm(-2) sr(-1) microm(-1)to rayleigh spectral radiance R(lambda) in rayleigh/microm, R(lambda) = 2pilambdaL(lambda) x 10(13), where the wavelength lambda is in microm. The rationale for the rayleigh unit is discussed in terms of a photon rate factor and a solid angle factor. The latter is developed in terms of an equivalence theorem about optical receivers and extended sources, and the concept is extended to the computation of photon volume emission rates from altitude profiles of zenith radiance.

Improvement of Radiological Teaching - Effects of Focusing of Learning Targets and Increased Consideration of Learning Theory Knowledge.

PubMed

Wirth, Stefan; William, York-Alexander; Paolini, Marco; Wirth, Kathrin; Maxien, Daniel; Reiser, Maximilian; Fischer, Martin R

2018-02-01

 Based on evaluation and examination results of students, a necessity for improvement of so far purely instructor-based radiological teaching at the local institution was determined. Aim of our study was to use one out of eight seminars to exemplify adaptation of the teaching concept according to learning theory knowledge, to determine the resulting effects and to interpret them.  The institutional review board approved the prospective study of the seminar conversion, which was performed after the end of the winter semester 2015/2016. Didactically, this included a course split into online preparation, attendance phase and online follow-up with integration of interactive scaffolding, practice-oriented clinical teaching according to Stanford, Peyton skills transfer and extensive feedback into the attendance phase. At the beginning and at the end of each course, each student filled in identical, standardized questionnaires (n = 256 before and after conversion) using a 5-point Likert scale (1: very good; to 5: deficient) and additionally answered two randomly chosen written examination questions from a content-adapted questionnaire pool of the last five years. For statistical evaluation, the Mann-Whitney U-Test was used for evaluation data and Fisher's Exact test for exam questions.  Before/after conversion, the subjective total evaluation score of students was 3.22 (mean value) ± 1.51 (standard deviation) / 1.66 ± 0.78 (p < 0.001) and the objective proportion of correctly answered examination questions in the respective cohort at the beginning of the seminar 37.7/53.9 % and at the end of the seminar 55.1/84.6 % (p < 0.001).  The conversion of the test seminar resulted in both a better evaluation of the teaching unit by the students (evaluation) and a considerably higher rate of correctly answered examination questions from past state examinations (learning success). This supports transferring the concept to comparable teaching units.   · Radiological teaching allows integration of current learning theory concepts with reasonable effort.. · In a test seminar this improved the evaluation results of the teaching unit by the students.. · In addition, this also led to a higher rate of correctly answered examination questions from past state examinations.. · This supports further steps towards excellent radiological teaching.. · Wirth S, William Y, Paolini M et al. Improvement of Radiological Teaching - Effects of Focusing of Learning Targets and Increased Consideration of Learning Theory Knowledge. Fortschr Röntgenstr 2018; 190: 161 - 174. © Georg Thieme Verlag KG Stuttgart · New York.

Addressing hypertext design and conversion issues

NASA Technical Reports Server (NTRS)

Glusko, Robert J.

1990-01-01

Hypertext is a network of information units connected by relational links. A hypertext system is a configuration of hardware and software that presents a hypertext to users and allows them to manage and access the information that it contains. Hypertext is also a user interface concept that closely supports the ways that people use printed information. Hypertext concepts encourage modularity and the elimination of redundancy in data bases because information can be stored only once but viewed in any appropriate context. Hypertext is such a hot idea because it is an enabling technology in that workstations and personal computers finally provide enough local processing power for hypertext user interfaces.

Biomass Feedstock and Conversion Supply System Design and Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobson, Jacob J.; Roni, Mohammad S.; Lamers, Patrick

Idaho National Laboratory (INL) supports the U.S. Department of Energy’s bioenergy research program. As part of the research program INL investigates the feedstock logistics economics and sustainability of these fuels. A series of reports were published between 2000 and 2013 to demonstrate the feedstock logistics cost. Those reports were tailored to specific feedstock and conversion process. Although those reports are different in terms of conversion, some of the process in the feedstock logistic are same for each conversion process. As a result, each report has similar information. A single report can be designed that could bring all commonality occurred inmore » the feedstock logistics process while discussing the feedstock logistics cost for different conversion process. Therefore, this report is designed in such a way that it can capture different feedstock logistics cost while eliminating the need of writing a conversion specific design report. Previous work established the current costs based on conventional equipment and processes. The 2012 programmatic target was to demonstrate a delivered biomass logistics cost of $55/dry ton for woody biomass delivered to fast pyrolysis conversion facility. The goal was achieved by applying field and process demonstration unit-scale data from harvest, collection, storage, preprocessing, handling, and transportation operations into INL’s biomass logistics model. The goal of the 2017 Design Case is to enable expansion of biofuels production beyond highly productive resource areas by breaking the reliance of cost-competitive biofuel production on a single, low-cost feedstock. The 2017 programmatic target is to supply feedstock to the conversion facility that meets the in-feed conversion process quality specifications at a total logistics cost of $80/dry T. The $80/dry T. target encompasses total delivered feedstock cost, including both grower payment and logistics costs, while meeting all conversion in-feed quality targets. The 2012 $55/dry T. programmatic target included only logistics costs with a limited focus on biomass quantity, quality and did not include a grower payment. The 2017 Design Case explores two approaches to addressing the logistics challenge: one is an agronomic solution based on blending and integrated landscape management and the second is a logistics solution based on distributed biomass preprocessing depots. The concept behind blended feedstocks and integrated landscape management is to gain access to more regional feedstock at lower access fees (i.e., grower payment) and to reduce preprocessing costs by blending high quality feedstocks with marginal quality feedstocks. Blending has been used in the grain industry for a long time; however, the concept of blended feedstocks in the biofuel industry is a relatively new concept. The blended feedstock strategy relies on the availability of multiple feedstock sources that are blended using a least-cost formulation within an economical supply radius, which, in turn, decreases the grower payment by reducing the amount of any single biomass. This report will introduce the concepts of blending and integrated landscape management and justify their importance in meeting the 2017 programmatic goals.« less

Analysis of digester design concepts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashare, E.; Wilson, E. H.

1979-01-29

Engineering economic analyses were performed on various digester design concepts to determine the relative performance for various biomass feedstocks. A comprehensive literature survey describing the state-of-the-art of the various digestion designs is included. The digester designs included in the analyses are CSTR, plug flow, batch, CSTR in series, multi-stage digestion and biomethanation. Other process options investigated included pretreatment processes such as shredding, degritting, and chemical pretreatment, and post-digestion processes, such as dewatering and gas purification. The biomass sources considered include feedlot manure, rice straw, and bagasse. The results of the analysis indicate that the most economical (on a unit gasmore » cost basis) digester design concept is the plug flow reactor. This conclusion results from this system providing a high gas production rate combined with a low capital hole-in-the-ground digester design concept. The costs determined in this analysis do not include any credits or penalties for feedstock or by-products, but present the costs only for conversion of biomass to methane. The batch land-fill type digester design was shown to have a unit gas cost comparable to that for a conventional stirred tank digester, with the potential of reducing the cost if a land-fill site were available for a lower cost per unit volume. The use of chemical pretreatment resulted in a higher unit gas cost, primarily due to the cost of pretreatment chemical. A sensitivity analysis indicated that the use of chemical pretreatment could improve the economics provided a process could be developed which utilized either less pretreatment chemical or a less costly chemical. The use of other process options resulted in higher unit gas costs. These options should only be used when necessary for proper process performance, or to result in production of a valuable by-product.« less

Air Brayton Solar Receiver, phase 1

NASA Technical Reports Server (NTRS)

Zimmerman, D. K.

1979-01-01

A six month analysis and conceptual design study of an open cycle Air Brayton Solar Receiver (ABSR) for use on a tracking, parabolic solar concentrator are discussed. The ABSR, which includes a buffer storage system, is designed to provide inlet air to a power conversion unit. Parametric analyses, conceptual design, interface requirements, and production cost estimates are described. The design features were optimized to yield a zero maintenance, low cost, high efficiency concept that will provide a 30 year operational life.

Proceedings of the Chornobyl phytoremediation and biomass energy conversion workshop (in English;Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartley, J.; Tokarevsky, V.

1998-06-01

Many concepts, systems, technical approaches, technologies, ideas, agreements, and disagreements were vigorously discussed during the course of the 2-day workshop. The workshop was successful in generating intensive discussions on the merits of the proposed concept that includes removal of radionuclides by plants and trees (phytoremediation) to clean up soil in the Chornobyl Exclusion Zone (CEZ), use of the resultant biomass (plants and trees) to generate electrical power, and incorporation of ash in concrete casks to be used as storage containers in a licensed repository for low-level waste. Twelve years after the Chornobyl Nuclear Power Plant (ChNPP) Unit 4 accident, whichmore » occurred on April 26, 1986, the primary 4radioactive contamination of concern is from radioactive cesium ({sup 137}Cs) and strontium ({sup 90}Sr). The {sup 137}Cs and {sup 90}Sr were widely distributed throughout the CEZ. The attendees from Ukraine, Russia, Belarus, Denmark and the US provided information, discussed and debated the following issues considerably: distribution and characteristics of radionuclides in CEZ; efficacy of using trees and plants to extract radioactive cesium (Cs) and strontium (Sr) from contaminated soil; selection of energy conversion systems and technologies; necessary infrastructure for biomass harvesting, handling, transportation, and energy conversion; radioactive ash and emission management; occupational health and safety concerns for the personnel involved in this work; and economics. The attendees concluded that the overall concept has technical and possibly economic merits. However, many issues (technical, economic, risk) remain to be resolved before a viable commercial-scale implementation could take place.« less

MHD compressor---expander conversion system integrated with GCR inside a deployable reflector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuninetti, G.; Botta, E.; Criscuolo, C.

1989-04-20

This work originates from the proposal MHD Compressor-Expander Conversion System Integrated with a GCR Inside a Deployable Reflector''. The proposal concerned an innovative concept of nuclear, closed-cycle MHD converter for power generation on space-based systems in the multi-megawatt range. The basic element of this converter is the Power Conversion Unit (PCU) consisting of a gas core reactor directly coupled to an MHD expansion channel. Integrated with the PCU, a deployable reflector provides reactivity control. The working fluid could be either uranium hexafluoride or a mixture of uranium hexafluoride and helium, added to enhance the heat transfer properties. The original Statementmore » of Work, which concerned the whole conversion system, was subsequently redirected and focused on the basic mechanisms of neutronics, reactivity control, ionization and electrical conductivity in the PCU. Furthermore, the study was required to be inherently generic such that the study was required to be inherently generic such that the analysis an results can be applied to various nuclear reactor and/or MHD channel designs''.« less

Solar thermal conversion

NASA Technical Reports Server (NTRS)

Selcuk, M. K.

1978-01-01

A brief review of the fundamentals of the conversion of solar energy into mechanical work (or electricity via generators) is given. Both past and present work on several conversion concepts are discussed. Solar collectors, storage systems, energy transport, and various types of engines are examined. Ongoing work on novel concepts of collectors, energy storage and thermal energy conversion are outlined and projections for the future are described. Energy costs for various options are predicted and margins and limitations are discussed.

The Concept and Experimental Investigation of CO2 and Steam Co-electrolysis for Resource Utilization in Space Exploration

NASA Technical Reports Server (NTRS)

Stoots, Carl; Mulloth, Lila M.; Luna, Bernadette; Varghese, Mini M.

2009-01-01

CO2 acquisition and utilization technologies will have a vital role in determining sustained and affordable life support and in-situ fuel production architectures for human and robotic exploration of Moon and Mars. For long-term human exploration to be practical, reliable technologies have to be implemented to capture and chemically reduce the metabolic CO2 from the cabin air to restitute oxygen consumption. Technologies that facilitate the in-situ capture and conversion of atmospheric CO2 to fuel are essential for a viable human mission to Mars and their demonstration on the moon is critical as well. This paper describes the concept and experimental investigation of a CO2 capture and reduction system that comprises an adsorption compressor and a CO2 and steam co-electrolysis unit. The process products include oxygen for life support and Syngas (CO and H2) for synthetic fuel production. Electrochemical performance in terms of CO2 conversion, oxygen production, and power consumption of a system with a capacity to process 1kg CO2 per day (1-person equivalent) will be discussed.

Advanced direct coal liquefaction concepts. Quarterly report, April 1, 1993--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

Construction and commissioning of the bench unit for operation of the first stage of the process was completed. Solubilization of Black Thunder coal using carbon monoxide and steam was successfully demonstrated in the counterflow reactor system. The results were comparable with those obtained in the autoclave with the exception that coal solubilization at the same nominal residence times was slightly lower. The bench unit has now been modified for two stage operation. The Wilsonville process derived solvent for Black Thunder coal (V-1074) was found to be essentially as stable as the previous solvent used in the autoclave runs (V-178 +more » 320) at reactor conditions. This solvent (V-1074) is, therefore, being used in the bench unit tests. Carbon monoxide may be replaced by synthesis gas for the coal solubilization step in the process. However, in autoclave tests, coal conversion was found to be dependent on the amount of carbon monoxide present in the synthesis gas. Coal conversions ranged from 88% for pure carbon monoxide to 67% for a 25:75 carbon monoxide/hydrogen mixture at equivalent conditions. Two stage liquefaction tests were completed in the autoclave using a disposable catalyst (FeS) and hydrogen in the second stage. Increased coal conversion, higher gas and oil and lower asphaltene and preasphaltene yields were observed as expected. However, no hydrogen consumption was observed in the second stage. Other conditions, in particular, alternate catalyst systems will be explored.« less

Conversational skills in a semistructured interview and self-concept in deaf students.

PubMed

Silvestre, Núria; Ramspott, Anna; Pareto, Irenka D

2007-01-01

The starting point for this study is the importance of linguistic competence in deaf students as part of their process of socialization and the formation of their self-concept. With the 56 deaf students who participated in the research, we consider the following sociodemographic variables: age, sex and degree of hearing loss, and the educational factor with respect to the mode of mainstream schooling. Self-concept was explored using the Spanish version of the Self Development Questionnaire (SDQ; I. Elexpuru, 1992) and the TST-Who Am I? test, adapted from M. H. Kuhn and T. S. McPartland (1954). To obtain the data for conversational competence, a conversation was held with a hearing adult. An explanation is given of the criteria for pragmatic analysis. The main results highlight the relationship between positive self-concept and most aspects of conversational competence. The study concludes with pedagogical procedures for integration, including specific strategies for teaching conversational skills to deaf pupils through nondeaf pupils and vice versa.

Characterizing the structure and content of nurse handoffs: A Sequential Conversational Analysis approach.

PubMed

Abraham, Joanna; Kannampallil, Thomas; Brenner, Corinne; Lopez, Karen D; Almoosa, Khalid F; Patel, Bela; Patel, Vimla L

2016-02-01

Effective communication during nurse handoffs is instrumental in ensuring safe and quality patient care. Much of the prior research on nurse handoffs has utilized retrospective methods such as interviews, surveys and questionnaires. While extremely useful, an in-depth understanding of the structure and content of conversations, and the inherent relationships within the content is paramount to designing effective nurse handoff interventions. In this paper, we present a methodological framework-Sequential Conversational Analysis (SCA)-a mixed-method approach that integrates qualitative conversational analysis with quantitative sequential pattern analysis. We describe the SCA approach and provide a detailed example as a proof of concept of its use for the analysis of nurse handoff communication in a medical intensive care unit. This novel approach allows us to characterize the conversational structure, clinical content, disruptions in the conversation, and the inherently phasic nature of nurse handoff communication. The characterization of communication patterns highlights the relationships underlying the verbal content of nurse handoffs with specific emphasis on: the interactive nature of conversation, relevance of role-based (incoming, outgoing) communication requirements, clinical content focus on critical patient-related events, and discussion of pending patient management tasks. We also discuss the applicability of the SCA approach as a method for providing in-depth understanding of the dynamics of communication in other settings and domains. Copyright © 2015 Elsevier Inc. All rights reserved.

MPPT Algorithm Development for Laser Powered Surveillance Camera Power Supply Unit

NASA Astrophysics Data System (ADS)

Zhang, Yungui; Dushantha Chaminda, P. R.; Zhao, Kun; Cheng, Lin; Jiang, Yi; Peng, Kai

2018-03-01

Photovoltaics (PV) cells, modules which are semiconducting materials, convert light energy into electricity. Operation of a PV cell requires 3 basic features. When the light is absorbed it generate pairs of electron holes or excitons. An external circuit carrier opposite types of electrons irrespective of the source (sunlight or LASER light). The PV arrays have photovoltaic effect and the PV cells are defined as a device which has electrical characteristics: such as current, voltage and resistance. It varies when exposed to light, that the power output is depend on direct Laser-light. In this paper Laser-light to electricity by direct conversion with the use of PV cells and its concept of Band gap Energy, Series Resistance, Conversion Efficiency and Maximum Power Point Tracking (MPPT) methods [1].

Emergence of biological organization through thermodynamic inversion.

PubMed

Kompanichenko, Vladimir

2014-01-01

Biological organization arises under thermodynamic inversion in prebiotic systems that provide the prevalence of free energy and information contribution over the entropy contribution. The inversion might occur under specific far-from-equilibrium conditions in prebiotic systems oscillating around the bifurcation point. At the inversion moment, (physical) information characteristic of non-biological systems acquires the new features: functionality, purposefulness, and control over the life processes, which transform it into biological information. Random sequences of amino acids and nucleotides, spontaneously synthesized in the prebiotic microsystem, in the primary living unit (probiont) re-assemble into functional sequences, involved into bioinformation circulation through nucleoprotein interaction, resulted in the genetic code emergence. According to the proposed concept, oscillating three-dimensional prebiotic microsystems transformed into probionts in the changeable hydrothermal medium of the early Earth. The inversion concept states that spontaneous (accidental, random) transformations in prebiotic systems cannot produce life; it is only non-spontaneous (perspective, purposeful) transformations, which are the result of thermodynamic inversion, that lead to the negentropy conversion of prebiotic systems into initial living units.

Megawatt Class Nuclear Space Power Systems (MCNSPS) conceptual design and evaluation report. Volume 3, technologies 2: Power conversion

NASA Technical Reports Server (NTRS)

Wetch, J. R.

1988-01-01

The major power conversion concepts considered for the Megawatt Class Nuclear Space Power System (MCNSPS) are discussed. These concepts include: (1) Rankine alkali-metal-vapor turbine alternators; (2) in-core thermionic conversion; (3) Brayton gas turbine alternators; and (4) free piston Stirling engine linear alternators. Considerations important to the coupling of these four conversion alternatives to an appropriate nuclear reactor heat source are examined along with the comparative performance characteristics of the combined systems meeting MCNSPS requirements.

"It's Insanely Useful!" Students' Use of Instructional Concepts in Group Work and Individual Writing

ERIC Educational Resources Information Center

Rodnes, Kari Anne

2012-01-01

This study investigates students' work on analyzing a literary text, a cartoon strip, with focus on their use of instructional, analytical concepts. Excerpts from a group conversation and from individually written texts are analyzed from a sociocultural, dialogical perspective. The analysis of the conversation shows how such concepts help the…

Novel Nuclear Powered Photocatalytic Energy Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

White,John R.; Kinsmen,Douglas; Regan,Thomas M.

2005-08-29

The University of Massachusetts Lowell Radiation Laboratory (UMLRL) is involved in a comprehensive project to investigate a unique radiation sensing and energy conversion technology with applications for in-situ monitoring of spent nuclear fuel (SNF) during cask transport and storage. The technology makes use of the gamma photons emitted from the SNF as an inherent power source for driving a GPS-class transceiver that has the ability to verify the position and contents of the SNF cask. The power conversion process, which converts the gamma photon energy into electrical power, is based on a variation of the successful dye-sensitized solar cell (DSSC)more » design developed by Konarka Technologies, Inc. (KTI). In particular, the focus of the current research is to make direct use of the high-energy gamma photons emitted from SNF, coupled with a scintillator material to convert some of the incident gamma photons into photons having wavelengths within the visible region of the electromagnetic spectrum. The high-energy gammas from the SNF will generate some power directly via Compton scattering and the photoelectric effect, and the generated visible photons output from the scintillator material can also be converted to electrical power in a manner similar to that of a standard solar cell. Upon successful implementation of an energy conversion device based on this new gammavoltaic principle, this inherent power source could then be utilized within SNF storage casks to drive a tamper-proof, low-power, electronic detection/security monitoring system for the spent fuel. The current project has addressed several aspects associated with this new energy conversion concept, including the development of a base conceptual design for an inherent gamma-induced power conversion unit for SNF monitoring, the characterization of the radiation environment that can be expected within a typical SNF storage system, the initial evaluation of Konarka's base solar cell design, the design and fabrication of a range of new cell materials and geometries at Konarka's manufacturing facilities, and the irradiation testing and evaluation of these new cell designs within the UML Radiation Laboratory. The primary focus of all this work was to establish the proof of concept of the basic gammavoltaic principle using a new class of dye-sensitized photon converter (DSPC) materials based on KTI's original DSSC design. In achieving this goal, this report clearly establishes the viability of the basic gammavoltaic energy conversion concept, yet it also identifies a set of challenges that must be met for practical implementation of this new technology.« less

27 CFR 19.722 - Conversion between metric and U.S. units.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Conversion between metric... General § 19.722 Conversion between metric and U.S. units. When liters are converted to wine gallons, the...: (a) If the conversion from liters to U.S. units is made before multiplying by the number of cases...

27 CFR 31.161 - Conversion between metric and U.S. units.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Conversion between metric... Wholesale Dealers' Records and Reports § 31.161 Conversion between metric and U.S. units. When liters are... number of cases to be converted, as follows: (a) If the conversion from liters to U.S. units is made...

Advanced direct liquefaction concepts for PETC generic units. Quarterly technical progress report, October 1992--December 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The reactivity of the THF insoluble fraction of the ashy resid component of Wilsonville recycle oil (WRO) during liquefaction of Black Thunder coal in tetralin was determined at 415{degrees}C and 60 minutes. The liquefaction runs were made by combining this material with Black Thunder coal at the same ratio used in the WRO coal runs. THF conversion and product distribution from liquefaction in tetralin in the presence of the THF insoluble fraction of the ashy resid were similar to results from liquefaction in WRO. THF conversion was greater than loot with an oil yield that was somewhat higher than inmore » WRO. Differences in HC gas yield and H{sub 2} consumption were slight, while conversion and product distribution from liquefaction of Black Thunder coal in tetralin or in the WRO distillate were quite different. In both these solvents the 85--86% THF conversions were less than for runs in which the THF insoluble fraction of the ashy resid was present. This establishes that the THF insoluble fraction of the ashy resid is the reactive fraction of the WRO.« less

IECEC '83; Proceedings of the Eighteenth Intersociety Energy Conversion Engineering Conference, Orlando, FL, August 21-26, 1983. Volume 1 - Thermal energy systems

NASA Astrophysics Data System (ADS)

Among the topics discussed are the nuclear fuel cycle, advanced nuclear reactor designs, developments in central status power reactors, space nuclear reactors, magnetohydrodynamic devices, thermionic devices, thermoelectric devices, geothermal systems, solar thermal energy conversion systems, ocean thermal energy conversion (OTEC) developments, and advanced energy conversion concepts. Among the specific questions covered under these topic headings are a design concept for an advanced light water breeder reactor, energy conversion in MW-sized space power systems, directionally solidified cermet electrodes for thermionic energy converters, boron-based high temperature thermoelectric materials, geothermal energy commercialization, solar Stirling cycle power conversion, and OTEC production of methanol. For individual items see A84-30027 to A84-30055

Multiple ways to the prior occurrence of an event: an electrophysiological dissociation of experimental and conceptually driven familiarity in recognition memory.

PubMed

Wiegand, Iris; Bader, Regine; Mecklinger, Axel

2010-11-11

Recent research has shown that familiarity contributes to associative memory when the to-be-associated stimuli are unitized during encoding. However, the specific processes underlying familiarity-based recognition of unitized representations are still indefinite. In this study, we present electrophysiologically dissociable early old/new effects, presumably related to two different kinds of familiarity inherent in associative recognition tasks. In a study-test associative recognition memory paradigm, we employed encoding conditions that established unitized representations of two pre-experimentally unrelated words, e.g. vegetable-bible. We compared event-related potentials (ERP) during the retrieval of these unitized word pairs using different retrieval cues. Word pairs presented in the same order as during unitization at encoding elicited a parietally distributed early old/new effect which we interpret as reflecting conceptually driven familiarity for newly formed concepts. Conversely, word pairs presented in reversed order only elicited a topographically dissociable early effect, i.e. the mid-frontal old/new effect, the putative correlate of experimental familiarity. The late parietal old/new effect, the putative ERP correlate of recollection, was obtained irrespective of word order, though it was larger for words presented in same order. These results indicate that familiarity may not be a unitary process and that different task demands can promote the assessment of conceptually driven familiarity for novel unitized concepts or experimentally-induced increments of experimental familiarity, respectively. Copyright © 2010 Elsevier B.V. All rights reserved.

In-Situ Resource Utilization Experiment for the Asteroid Redirect Crewed Mission

NASA Astrophysics Data System (ADS)

Elliott, J.; Fries, M.; Love, S.; Sellar, R. G.; Voecks, G.; Wilson, D.

2015-10-01

The Asteroid Redirect Crewed Mission (ARCM) represents a unique opportunity to perform in-situ testing of concepts that could lead to full-scale exploitation of asteroids for their valuable resources [1]. This paper describes a concept for an astronautoperated "suitcase" experiment to would demonstrate asteroid volatile extraction using a solar-heated oven and integral cold trap in a configuration scalable to full-size asteroids. Conversion of liberated water into H2 and O2 products would also be demonstrated through an integral processing and storage unit. The plan also includes development of a local prospecting system consisting of a suit-mounted multi-spectral imager to aid the crew in choosing optimal samples, both for In-Situ Resource Utilization (ISRU) and for potential return to Earth.

Waveform generation in the EETS

NASA Astrophysics Data System (ADS)

Wilshire, J. P.

1985-05-01

Design decisions and analysis for the waveform generation portion of an electrical equipment test set are discussed. This test set is unlike conventional ATE in that it is portable and designed to operate in forward area sites for the USMC. It is also unique in that it provides for functional testing for 32 electronic units from the AV-88 Harrier II aircraft. Specific requirements for the waveform generator are discussed, including a wide frequency range, high resolution and accuracy, and low total harmonic distortion. Several approaches to meet these requirements are considered and a specific concept is presented in detail, which consists of a digitally produced waveform that feeds a deglitched analog conversion circuit. Rigorous mathematical analysis is presented to prove that this concept meets the requirements. Finally, design alternatives and enhancements are considered.

Radiation energy conversion in space; Conference, 3rd, NASA Ames Research Center, Moffett Field, Calif., January 26-28, 1978, Technical Papers

NASA Technical Reports Server (NTRS)

Billman, K. W.

1978-01-01

Concepts for space-based conversion of space radiation energy into useful energy for man's needs are developed and supported by studies of costs, material and size requirements, efficiency, and available technology. Besides the more studied solar power satellite system using microwave transmission, a number of alternative space energy concepts are considered. Topics covered include orbiting mirrors for terrestrial energy supply, energy conversion at a lunar polar site, ultralightweight structures for space power, radiatively sustained cesium plasmas for solar electric conversion, solar pumped CW CO2 laser, superelastic laser energy conversion, laser-enhanced dynamics in molecular rate processes, and electron beams in space for energy storage.

A Closed Brayton Power Conversion Unit Concept for Nuclear Electric Propulsion for Deep Space Missions

NASA Astrophysics Data System (ADS)

Joyner, Claude Russell; Fowler, Bruce; Matthews, John

2003-01-01

In space, whether in a stable satellite orbit around a planetary body or traveling as a deep space exploration craft, power is just as important as the propulsion. The need for power is especially important for in-space vehicles that use Electric Propulsion. Using nuclear power with electric propulsion has the potential to provide increased payload fractions and reduced mission times to the outer planets. One of the critical engineering and design aspects of nuclear electric propulsion at required mission optimized power levels is the mechanism that is used to convert the thermal energy of the reactor to electrical power. The use of closed Brayton cycles has been studied over the past 30 or years and shown to be the optimum approach for power requirements that range from ten to hundreds of kilowatts of power. It also has been found to be scalable to higher power levels. The Closed Brayton Cycle (CBC) engine power conversion unit (PCU) is the most flexible for a wide range of power conversion needs and uses state-of-the-art, demonstrated engineering approaches. It also is in use with many commercial power plants today. The long life requirements and need for uninterrupted operation for nuclear electric propulsion demands high reliability from a CBC engine. A CBC engine design for use with a Nuclear Electric Propulsion (NEP) system has been defined based on Pratt & Whitney's data from designing long-life turbo-machines such as the Space Shuttle turbopumps and military gas turbines and the use of proven integrated control/health management systems (EHMS). An integrated CBC and EHMS design that is focused on using low-risk and proven technologies will over come many of the life-related design issues. This paper will discuss the use of a CBC engine as the power conversion unit coupled to a gas-cooled nuclear reactor and the design trends relative to its use for powering electric thrusters in the 25 kWe to 100kWe power level.

Fuel development for gas-cooled fast reactors

NASA Astrophysics Data System (ADS)

Meyer, M. K.; Fielding, R.; Gan, J.

2007-09-01

The Generation IV Gas-cooled Fast Reactor (GFR) concept is proposed to combine the advantages of high-temperature gas-cooled reactors (such as efficient direct conversion with a gas turbine and the potential for application of high-temperature process heat), with the sustainability advantages that are possible with a fast-spectrum reactor. The latter include the ability to fission all transuranics and the potential for breeding. The GFR is part of a consistent set of gas-cooled reactors that includes a medium-term Pebble Bed Modular Reactor (PBMR)-like concept, or concepts based on the Gas Turbine Modular Helium Reactor (GT-MHR), and specialized concepts such as the Very High-Temperature Reactor (VHTR), as well as actinide burning concepts [A Technology Roadmap for Generation IV Nuclear Energy Systems, US DOE Nuclear Energy Research Advisory Committee and the Generation IV International Forum, December 2002]. To achieve the necessary high power density and the ability to retain fission gas at high temperature, the primary fuel concept proposed for testing in the United States is dispersion coated fuel particles in a ceramic matrix. Alternative fuel concepts considered in the US and internationally include coated particle beds, ceramic clad fuel pins, and novel ceramic 'honeycomb' structures. Both mixed carbide and mixed nitride-based solid solutions are considered as fuel phases.

Beyond Simple Planning: Existential Dimensions of Conversations With Patients at Risk of Dying From Heart Failure.

PubMed

Schulz, Valerie Marie; Crombeen, Allison M; Marshall, Denise; Shadd, Joshua; LaDonna, Kori A; Lingard, Lorelei

2017-11-01

Despite the recent promotion of communication guides to improve decision making with patients nearing the end of their lives, these conversations remain challenging. Deeper and more comprehensive understanding of communication barriers that undermine discussions and decisions with patients at risk of dying from heart failure (HF) is vital for informing communication in health care. To explore experiences and perspectives of patients with advanced HF, their caregivers, and providers, regarding conversations for patients at risk of dying from HF. Following Research Ethics Board approval, index patients with advanced HF (New York Heart Association III or IV) and consenting patient-identified care team members were interviewed. A team sampling unit was formed when the patient plus at least two additional team members participated in interviews. Team members included health professionals (e.g., cardiologist, family physician, HF nurse practitioner, social worker, and specialists, such as respirologist, nephrologist, palliative care physician), family caregivers (e.g., daughter, spouse, roommate, close friend), and community members (e.g., minister, neighbor, regular taxi driver). Our data set included 209 individual interviews clustered into 50 team sampling units at five sites from three Canadian provinces. Key informants, identified as practicing experts in the field, reviewed our initial findings with attention to relevance to practice as a form of triangulation. Iterative data collection and analysis followed constructivist grounded theory procedures with sensitizing concepts drawn from complexity theory. To ensure confidentiality, all participants were given a pseudonym. Participants' reports of their perceptions and experiences of conversations related to death and dying suggested two main dimensions of such conversations: instrumental and existential. Instrumental dimensions included how these conversations were planned and operationalized as well as the triggers and barriers to these discussions. Existential dimensions of these conversations included evasive maneuvers, powerful emotions, and the phenomenon of death without dying. Existential dimensions appeared to have a basis in issues of mortality and could strongly influence conversations related to death and dying. Conversations for patients at risk of dying from HF have both instrumental and existential dimensions, in which routines and relationships are inseparable. Our current focus on the instrumental aspects of these conversations is necessary but insufficient. The existential dimensions of conversations related to death are profound and may explain why these conversations have struggled to achieve their desired effect. To improve this communication, we need to also attend to existential dimensions, particularly in terms of their impact on the occurrence of these conversations, the nature of relationships and responses within these conversations, and the fluidity of meaning within these conversations. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

Metric Conversion

Atmospheric Science Data Center

2013-03-12

Metric Weights and Measures The metric system is based on 10s.  For example, 10 millimeters = 1 centimeter, 10 ... Special Publications: NIST Guide to SI Units: Conversion Factors NIST Guide to SI Units: Conversion Factors listed ...

Satellite Power Study (SPS) concept definition study (Exhibit D). Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1981-01-01

Efforts concentrated on updating of the Rockwell reference concept, definition of new system options, studies of special emphasis topics, further definition of the transportation system, and further program definition. The Rockwell reference satellite concept has a gallium arsenide (GaAs) solar cell array having flat concentrators with an effective concentration ratio of 1.83at end of life. Alternatives to this concept includes solid state power amplifiers or magnetrons for dc/RF conversion and multibandgap solar cells for solar to dc energy conversion. Two solid state concepts were studied. It was determined that the magnetron approach was the lowest mass and cost system.

A comparison of Stirling engines for use with a 25 kW dish-electric conversion system

NASA Technical Reports Server (NTRS)

Shaltens, Richard K.

1987-01-01

Two designs for an advanced Stirling conversion system (ASCS) are described. The objective of the ASCS is to generate about 25 kW of electric power to an electric utility grid at an engine/alternator target cost of $300.00/kW at the manufacturing rate of 10,000 unit/yr. Both designs contain a free-piston Stirling engine (FPSE), a heat transport system, solar receiver, a means to generate electric power, the necessary auxiliaries, and a control system. The major differences between the two concepts are: one uses a 25 kWe single-piston FPSE which incorporates a linear alternator to directly convert the energy to electricity on the utility grid; and in the second design, electrical power is generated indirectly using a hydraulic output to a ground based hydraulic motor coupled to a rotating alternator. Diagrams of the two designs are presented.

Direct conversion technology

NASA Technical Reports Server (NTRS)

Massier, P. F.; Bankston, C. P.; Fabris, G.; Kirol, L. D.

1988-01-01

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct thermal-to-electric energy conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal MHD Electrical Generator (LMMHD) for the period January 1988 through December 1988. Research on these concepts was initiated during October 1987. In addition, status reviews and assessments are presented for thermomagnetic converter concepts and for thermoelastic converters (Nitinol heat engines). Reports prepared on previous occasions contain discussions on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic thermophotovoltaic and thermoacoustic; and also, more complete discussions of AMTEC and LMMHD systems. A tabulated summary of the various systems which have been reviewed thus far has been prepared. Some of the important technical research needs are listed and a schematic of each system is shown.

Direct conversion technology

NASA Technical Reports Server (NTRS)

Massier, Paul F.; Bankston, C. P.; Williams, R.; Underwood, M.; Jeffries-Nakamura, B.; Fabris, G.

1989-01-01

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal Magnetohydrodynamic Electrical Generator (LMMHD) for the period January 1, 1989 through December 31, 1989. Research on these concepts was initiated during October 1987. Reports prepared on previous occasions contain discussions on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic, thermophotovoltaic, thermoacoustic, thermomagnetic, thermoelastic (nitinol heat engines); and also, more complete discussions of AMTEC and LMMHD systems.

A model for production, perception, and acquisition of actions in face-to-face communication.

PubMed

Kröger, Bernd J; Kopp, Stefan; Lowit, Anja

2010-08-01

The concept of action as basic motor control unit for goal-directed movement behavior has been used primarily for private or non-communicative actions like walking, reaching, or grasping. In this paper, literature is reviewed indicating that this concept can also be used in all domains of face-to-face communication like speech, co-verbal facial expression, and co-verbal gesturing. Three domain-specific types of actions, i.e. speech actions, facial actions, and hand-arm actions, are defined in this paper and a model is proposed that elucidates the underlying biological mechanisms of action production, action perception, and action acquisition in all domains of face-to-face communication. This model can be used as theoretical framework for empirical analysis or simulation with embodied conversational agents, and thus for advanced human-computer interaction technologies.

Global rotation of mechanical metamaterials induced by their internal deformation

NASA Astrophysics Data System (ADS)

Dudek, K. K.; Gatt, R.; Mizzi, L.; Dudek, M. R.; Attard, D.; Grima, J. N.

2017-09-01

In this work, we propose the concept that a device based on mechanical metamaterials can be used to induce and control its own rotational motion as a result of internal deformations due to the conversion of translational degrees of freedom into rotational ones. The application of a linear force on the structural units of the system may be fine-tuned in order to obtain a desired type of rotation. In particular, we show, how it is possible to maximise the extent of rotation of the system through the alteration of the geometry of the system. We also show how a device based on this concept can be connected to an external body in order to rotate it which result may potentially prove to be very important in the case of applications such as telescopes employed in space.

Contribution to solving the energy crisis - Simulating the prospects for low cost energy through silicon solar cells

NASA Technical Reports Server (NTRS)

Kran, A.

1978-01-01

PECAN (Photovoltaic Energy Conversion Analysis) is a highly interactive decision analysis and support system. It simulates the prospects for widespread use of solar cells for the generation of electrical power. PECAN consists of a set of integrated APL functions for evaluating the potential of terrestrial photovoltaics. Specifically, the system is a deterministic simulator, which translates present and future manufacturing technology into economic and financial terms, using the production unit concept. It guides solar cell development in three areas: tactical decision making, strategic planning, and the formulation of alternative options.

Social Media and Men's Health: A Content Analysis of Twitter Conversations During the 2013 Movember Campaigns in the United States, Canada, and the United Kingdom.

PubMed

Bravo, Caroline A; Hoffman-Goetz, Laurie

2017-11-01

The Movember Foundation raises awareness and funds for men's health issues such as prostate and testicular cancers in conjunction with a moustache contest. The 2013 Movember campaigns in the United States, Canada, and the United Kingdom shared the same goal of creating conversations about men's health that lead to increased awareness and understanding of the health risks men face. Our objective was to explore Twitter conversations to identify whether the 2013 Movember campaigns sparked global conversations about prostate cancer, testicular cancer, and other men's health issues. We conducted a content analysis of 12,666 tweets posted during the 2013 Movember campaigns in the United States, Canada, and the United Kingdom (4,222 tweets from each country) to investigate whether tweets were health-related or non-health-related and to determine what topics dominated conversations. Few tweets ( n = 84, 0.7% of 12,666 tweets) provided content-rich or actionable health information that would lead to awareness and understanding of men's health risks. While moustache growing and grooming was the most popular topic in U.S. tweets, conversations about community engagement were most common in Canadian and U.K. tweets. Significantly more tweets co-opted the Movember campaign to market products or contests in the United States than Canada and the United Kingdom ( p < .05). Findings from this content analysis of Twitter suggest that the 2013 Movember campaigns in the United States, Canada, and the United Kingdom sparked few conversations about prostate and testicular cancers that could potentially lead to greater awareness and understanding of important men's health issues.

Social Facilitation Effects by Pedagogical Conversational Agent: Lexical Network Analysis in an Online Explanation Task

ERIC Educational Resources Information Center

Hayashi, Yugo

2015-01-01

The present study investigates web-based learning activities of undergraduate students who generate explanations about a key concept taught in a large-scale classroom. The present study used an online system with Pedagogical Conversational Agent (PCA), asked to explain about the key concept from different points and provided suggestions and…

Investigation of direct solar-to-microwave energy conversion techniques

NASA Technical Reports Server (NTRS)

Chatterton, N. E.; Mookherji, T. K.; Wunsch, P. K.

1978-01-01

Identification of alternative methods of producing microwave energy from solar radiation for purposes of directing power to the Earth from space is investigated. Specifically, methods of conversion of optical radiation into microwave radiation by the most direct means are investigated. Approaches based on demonstrated device functioning and basic phenomenologies are developed. There is no system concept developed, that is competitive with current baseline concepts. The most direct methods of conversion appear to require an initial step of production of coherent laser radiation. Other methods generally require production of electron streams for use in solid-state or cavity-oscillator systems. Further development is suggested to be worthwhile for suggested devices and on concepts utilizing a free-electron stream for the intraspace station power transport mechanism.

40 CFR 61.67 - Emission tests.

Code of Federal Regulations, 2011 CFR

2011-07-01

... = Conversion factor from ppmw to units of emission standard, 0.001 (metric units) = 0.002 (English units) PPVC...(a), or § 61.64(a)(1), (b), (c), or (d), or from any control system to which reactor emissions are... conversion factor, 1,000 g/kg (1 lb/lb). 10−6 = Conversion factor for ppm. Z = Production rate, kg/hr (lb/hr...

40 CFR 61.67 - Emission tests.

Code of Federal Regulations, 2012 CFR

2012-07-01

... = Conversion factor from ppmw to units of emission standard, 0.001 (metric units) = 0.002 (English units) PPVC...(a), or § 61.64(a)(1), (b), (c), or (d), or from any control system to which reactor emissions are... conversion factor, 1,000 g/kg (1 lb/lb). 10−6 = Conversion factor for ppm. Z = Production rate, kg/hr (lb/hr...

Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 1: Introduction and summary and general assumptions. [energy conversion systems for electric power plants using coal - feasibility

NASA Technical Reports Server (NTRS)

Beecher, D. T.

1976-01-01

Nine advanced energy conversion concepts using coal or coal-derived fuels are summarized. They are; (1) open-cycle gas turbines, (2) combined gas-steam turbine cycles, (3) closed-cycle gas turbines, (4) metal vapor Rankine topping, (5) open-cycle MHD; (6) closed-cycle MHD; (7) liquid-metal MHD; (8) advanced steam; and (9) fuel cell systems. The economics, natural resource requirements, and performance criteria for the nine concepts are discussed.

12 CFR 563b.650 - What must I include in my plan of voluntary supervisory conversion?

Code of Federal Regulations, 2010 CFR

2010-01-01

... purchaser of conversion shares and a description of that purchaser's relationship to you. (c) The title, per-unit par value, number, and per-unit and aggregate offering price of shares that you will issue. (d... OF THE TREASURY CONVERSIONS FROM MUTUAL TO STOCK FORM Voluntary Supervisory Conversions Plan of...

Perezhivanie and classroom discourse: a cultural-historical perspective on "Discourse of design based science classroom activities"

NASA Astrophysics Data System (ADS)

Adams, Megan; March, Sue

2015-06-01

Flavio Azevedo, Peggy Martalock and Tugba Keser challenge the `argumentation focus of science lessons' and propose that through a `design-based approach' emergent conversations with the teacher offer possibilities for different types of discussions to enhance pedagogical discourse in science classrooms. This important paper offers a "preliminary contribution to a general theory" regarding the link between activity types and discourse practices. Azevedo, Martalock and Keser offer a general perspective with a sociocultural framing for analysis of classroom discourse. Interestingly the specific concepts drawn upon are from conversation analysis; there are few sociocultural concepts explored in detail. Therefore, in this article we focus on a cultural historical (Vygotsky in The collected works of L. S. Vygotsky. The history and development of higher mental functions, vol 4. Plenum Press, New York, 1987; The Vygotsky reader. Black, Cambridge, 1994) methodology to explore, analyse and explain how we would use a different theoretical lens. We argue that a cultural historical reading of argumentation in science lessons and design based activity will expand Azevedo, Martalock and Keser's proposed general theory of activity types and discourse practices. Specifically, we use Lev Vygotksy's idea of perezhivanie as the unit of analysis to reconceptualise this important paper. We focus on the holistic category of students' emotional experience through discourse while developing scientific awareness.

Chart of conversion factors: From English to metric system and metric to English system

USGS Publications Warehouse

,

1976-01-01

The conversion factors in the following tables are for conversion of our customary (English) units of measurement to SI*units, and for convenience, reciprocals are shown for converting SI units back to the English system. The first table contains rule-of-thumb figures, useful for "getting the feel" of SI units or mental estimation. The succeeding tables contain factors accurate to 3 or more significant figures. Please refer to known reference volumes for additional accuracy, as well as for factors dealing with other scientific notation involving SI units.

Common conversion factors.

PubMed

2001-05-01

This appendix presents tables of some of the more common conversion factors for units of measure used throughout Current Protocols manuals, as well as prefixes indicating powers of ten for SI units. Another table gives conversions between temperatures on the Celsius (Centigrade) and Fahrenheit scales.

Children's Self-Esteem and Moral Self: Links to Parent-Child Conversations Regarding Emotion

ERIC Educational Resources Information Center

Reese, Elaine; Bird, Amy; Tripp, Gail

2007-01-01

The current study has two aims: (1) to examine associations between the emotional content of parent-child past event conversations and two aspects of children's self-concept--moral self and self-esteem; and (2) to examine the degree to which talk about past events is uniquely associated with self-concept when compared with talk about ongoing…

System International d'Unites: Metric Measurement in Water Resources Engineering.

ERIC Educational Resources Information Center

Klingeman, Peter C.

This pamphlet gives definitions and symbols for the basic and derived metric units, prefixes, and conversion factors for units frequently used in water resources. Included are conversion factors for units of area, work, heat, power, pressure, viscosity, flow rate, and others. (BB)

Experience with SI units in biochemistry.

PubMed

Karnauchow, P N; Suvanto, L

1976-03-20

Use of Système International d'Unités (SI) for laboratory measurements was instituted Jan. 1, 1975 at two community hospitals. Beforehand, talks were given, pamphlets, conversion tables, new calibration curves and new master record cards were printed, computer cards were reprogrammed and conversion kits were prepared; the total cost was less than $200. After 6 months 16% of the medical staff had stopped converting SI units into conventional units, 78% were still occasionally converting units and 6% were routinely converting units. Changeover had been difficult for 25%, only a nuisance for 49% and easy for 26%. The patients' lives were not endangered by conversion.

Reported Speech in Conversational Storytelling during Nursing Shift Handover Meetings

ERIC Educational Resources Information Center

Bangerter, Adrian; Mayor, Eric; Pekarek Doehler, Simona

2011-01-01

Shift handovers in nursing units involve formal transmission of information and informal conversation about non-routine events. Informal conversation often involves telling stories. Direct reported speech (DRS) was studied in handover storytelling in two nursing care units. The study goal is to contribute to a better understanding of conversation…

40 CFR 98.253 - Calculating GHG emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (metric tons/year). 0.98 = Assumed combustion efficiency of a flare. 0.001 = Unit conversion factor... measurement values within the day to calculate a daily average. MVC = Molar volume conversion factor (849.5....001 = Unit conversion factor (metric tons per kilogram, mt/kg). n = Number of measurement periods. The...

Direct digital conversion detector technology

NASA Astrophysics Data System (ADS)

Mandl, William J.; Fedors, Richard

1995-06-01

Future imaging sensors for the aerospace and commercial video markets will depend on low cost, high speed analog-to-digital (A/D) conversion to efficiently process optical detector signals. Current A/D methods place a heavy burden on system resources, increase noise, and limit the throughput. This paper describes a unique method for incorporating A/D conversion right on the focal plane array. This concept is based on Sigma-Delta sampling, and makes optimum use of the active detector real estate. Combined with modern digital signal processors, such devices will significantly increase data rates off the focal plane. Early conversion to digital format will also decrease the signal susceptibility to noise, lowering the communications bit error rate. Computer modeling of this concept is described, along with results from several simulation runs. A potential application for direct digital conversion is also reviewed. Future uses for this technology could range from scientific instruments to remote sensors, telecommunications gear, medical diagnostic tools, and consumer products.

HydroUnits: A Python-based Physical Units Management Tool in Hydrologic Computing Systems

NASA Astrophysics Data System (ADS)

Celicourt, P.; Piasecki, M.

2015-12-01

While one objective of data management systems is to provide the units when annotating the collected data, another is that the units must be correctly manipulated during conversion steps. This is not a trivial task however and the units conversion time and errors for large datasets can be quite expensive. To date, more than a dozen Python modules have been developed to deal with units attached to quantities. However, they fall short in many ways and also suffer from not integrating with a units controlled vocabulary. Moreover, none of them permits the encoding of some complex units defined in the Consortium of Universities for the Advancement of Hydrologic Sciences, Inc.'s Observations Data Model (CUAHSI ODM) as a vectorial representation for storage demand reduction and does not incorporate provision to accommodate unforeseen standards-based units. We developed HydroUnits, a Python-based units management tool for three specific purposes: encoding of physical units in the Transducer Electronic Data Sheet (TEDS) as defined in the IEEE 1451.0 standard, performing dimensional analysis and on-the-fly conversion of time series allowing users to retrieve data from a data source in a desired equivalent unit while accommodating unforeseen and user-defined units. HydroUnits differentiates itself to existing tools by a number of factors including the implementation approach adopted, the adoption of standard-based units naming conventions and more importantly the emphasis on units controlled vocabularies which are a critical aspect of units treatment. Additionally, HydroUnits supports unit conversion for quantities with additive scaling factor, and natively supports time series conversion and takes leap years into consideration for units consisting of the time dimension (e.g., month, minute). Due to its overall implementation approach, HydroUnits exhibits a high level of versatility that no other tool we are aware of has achieved.

Concept report: Microprocessor control of electrical power system

NASA Technical Reports Server (NTRS)

Perry, E.

1977-01-01

An electrical power system which uses a microprocessor for systems control and monitoring is described. The microprocessor controlled system permits real time modification of system parameters for optimizing a system configuration, especially in the event of an anomaly. By reducing the components count, the assembling and testing of the unit is simplified, and reliability is increased. A resuable modular power conversion system capable of satisfying a large percentage of space applications requirements is examined along with the programmable power processor. The PC global controller which handles systems control and external communication is analyzed, and a software description is given. A systems application summary is also included.

Increasing conversion efficiency of two-step photon up-conversion solar cell with a voltage booster hetero-interface.

PubMed

Asahi, Shigeo; Kusaki, Kazuki; Harada, Yukihiro; Kita, Takashi

2018-01-17

Development of high-efficiency solar cells is one of the attractive challenges in renewable energy technologies. Photon up-conversion can reduce the transmission loss and is one of the promising concepts which improve conversion efficiency. Here we present an analysis of the conversion efficiency, which can be increased by up-conversion in a single-junction solar cell with a hetero-interface that boosts the output voltage. We confirm that an increase in the quasi-Fermi gap and substantial photocurrent generation result in a high conversion efficiency.

Quantification and characterization of grouped type I myofibers in human aging.

PubMed

Kelly, Neil A; Hammond, Kelley G; Stec, Michael J; Bickel, C Scott; Windham, Samuel T; Tuggle, S Craig; Bamman, Marcas M

2018-01-01

Myofiber type grouping is a histological hallmark of age-related motor unit remodeling. Despite the accepted concept that denervation-reinnervation events lead to myofiber type grouping, the completeness of those conversions remains unknown. Type I myofiber grouping was assessed in vastus lateralis biopsies from Young (26 ± 4 years; n = 27) and Older (66 ± 4 years; n = 91) adults. Grouped and ungrouped type I myofibers were evaluated for phenotypic differences. Higher type I grouping in Older versus Young was driven by more myofibers per group (i.e., larger group size) (P < 0.05). In Older only, grouped type I myofibers displayed larger cross-sectional area, more myonuclei, lower capillary supply, and more sarco(endo)plasmic reticulum calcium ATPase I (SERCA I) expression (P < 0.05) than ungrouped type I myofibers. Grouped type I myofibers retain type II characteristics suggesting that conversion during denervation-reinnervation events is either progressive or incomplete. Muscle Nerve 57: E52-E59, 2018. © 2017 Wiley Periodicals, Inc.

Thermoacoustically driven triboelectric nanogenerator: Combining thermoacoustics and nanoscience

NASA Astrophysics Data System (ADS)

Zhu, Shunmin; Yu, Aifang; Yu, Guoyao; Liu, Yudong; Zhai, Junyi; Dai, Wei; Luo, Ercang

2017-10-01

A thermoacoustic heat engine (TAHE) is a type of regenerative heat engine that converts external heat into mechanical power in the form of an acoustic wave with no moving mechanical components. One significant application of the TAHE is the generation of electricity by coupling an acoustic-to-electric conversion unit such as a linear motor or a piezoelectric ceramic assembly. However, present-day conversion technologies have considerable drawbacks, including structural complexity, high cost, and low reliability. The advent of triboelectric nanogenerators (TENGs) offers an alternative means to overcoming these shortcomings. In this paper, we propose a thermoacoustically driven TENG (TA-TENG) that continuously harvests external heat. A test rig involving a standing-wave TAHE and a contact-separation mode TENG was fabricated to demonstrate this concept. Currently, the TA-TENG produces a maximum output voltage of 10 V and a corresponding output power of 0.008 μW with a load of 400 MΩ, demonstrating the viability of this hybrid combination for electricity generation.

49 CFR 171.10 - Units of measure.

Code of Federal Regulations, 2011 CFR

2011-10-01

... measure in this subchapter are expressed using the International System of Units (“SI” or metric). Where... abbreviated. (c) Conversion values. (1) Conversion values are provided in the following table and are based on values provided in ASTM E 380, “Standard for Metric Practice”. (2) If an exact conversion is needed, the...

49 CFR 171.10 - Units of measure.

Code of Federal Regulations, 2012 CFR

2012-10-01

... measure in this subchapter are expressed using the International System of Units (“SI” or metric). Where... abbreviated. (c) Conversion values. (1) Conversion values are provided in the following table and are based on values provided in ASTM E 380, “Standard for Metric Practice”. (2) If an exact conversion is needed, the...

49 CFR 171.10 - Units of measure.

Code of Federal Regulations, 2014 CFR

2014-10-01

... measure in this subchapter are expressed using the International System of Units (“SI” or metric). Where... abbreviated. (c) Conversion values. (1) Conversion values are provided in the following table and are based on values provided in ASTM E 380, “Standard for Metric Practice”. (2) If an exact conversion is needed, the...

49 CFR 171.10 - Units of measure.

Code of Federal Regulations, 2010 CFR

2010-10-01

... measure in this subchapter are expressed using the International System of Units (“SI” or metric). Where... abbreviated. (c) Conversion values. (1) Conversion values are provided in the following table and are based on values provided in ASTM E 380, “Standard for Metric Practice”. (2) If an exact conversion is needed, the...

49 CFR 171.10 - Units of measure.

Code of Federal Regulations, 2013 CFR

2013-10-01

... measure in this subchapter are expressed using the International System of Units (“SI” or metric). Where... abbreviated. (c) Conversion values. (1) Conversion values are provided in the following table and are based on values provided in ASTM E 380, “Standard for Metric Practice”. (2) If an exact conversion is needed, the...

Computing with impure numbers - Automatic consistency checking and units conversion using computer algebra

NASA Technical Reports Server (NTRS)

Stoutemyer, D. R.

1977-01-01

The computer algebra language MACSYMA enables the programmer to include symbolic physical units in computer calculations, and features automatic detection of dimensionally-inhomogeneous formulas and conversion of inconsistent units in a dimensionally homogeneous formula. Some examples illustrate these features.

Direct conversion technology: Annual summary report CY 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Massier, P.F.; Bankston, C.P.; Fabris, G.

1988-12-01

The overall objective of the Direct Conversion Technology task is to develop an experimentally verified technology base for promising direct thermal-to-electric energy conversion systems that have potential application for energy conservation in the end-use sectors. This report contains progress of research on the Alkali Metal Thermal-to-Electric Converter (AMTEC), and on the Two-Phase Liquid-Metal MHD Electrical Generator (LMMHD) for the period January 1988 through December 1988. Research on these concepts was initiated during October 1987. In addition, status reviews and assessments are presented for thermomagnetic converter concepts and for thermoelastic converters (Nitinol heat engines). Reports prepared on previous occasions contain discussionsmore » on the following other direct conversion concepts: thermoelectric, pyroelectric, thermionic thermophotovoltaic and thermoacoustic; and also, more complete discussions of AMTEC and LMMHD systems. A tabulated summary of the various systems which have been reviewed thus far has been prepared. Some of the important technical research needs are listed and a schematic of each system is shown. These tabulations are included herein as figures. 43 refs., 26 figs., 1 tab.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lebarbier Dagel, Vanessa M.; Li, J.; Taylor, Charles E.

This collaborative joint research project is in the area of advanced gasification and conversion, within the Chinese Academy of Sciences (CAS)-National Energy Technology Laboratory (NETL)-Pacific Northwest National Laboratory (PNNL) Memorandum of Understanding. The goal for this subtask is the development of advanced syngas conversion technologies. Two areas of investigation were evaluated: Sorption-Enhanced Synthetic Natural Gas Production from Syngas The conversion of synthetic gas (syngas) to synthetic natural gas (SNG) is typically catalyzed by nickel catalysts performed at moderate temperatures (275 to 325°C). The reaction is highly exothermic and substantial heat is liberated, which can lead to process thermal imbalance andmore » destruction of the catalyst. As a result, conversion per pass is typically limited, and substantial syngas recycle is employed. Commercial methanation catalysts and processes have been developed by Haldor Topsoe, and in some reports, they have indicated that there is a need and opportunity for thermally more robust methanation catalysts to allow for higher per-pass conversion in methanation units. SNG process requires the syngas feed with a higher H2/CO ratio than typically produced from gasification processes. Therefore, the water-gas shift reaction (WGS) will be required to tailor the H2/CO ratio. Integration with CO2 separation could potentially eliminate the need for a separate WGS unit, thereby integrating WGS, methanation, and CO2 capture into one single unit operation and, consequently, leading to improved process efficiency. The SNG process also has the benefit of producing a product stream with high CO2 concentrations, which makes CO2 separation more readily achievable. The use of either adsorbents or membranes that selectively separate the CO2 from the H2 and CO would shift the methanation reaction (by driving WGS for hydrogen production) and greatly improve the overall efficiency and economics of the process. The scope of this activity was to develop methods and enabling materials for syngas conversion to SNG with readily CO2 separation. Suitable methanation catalyst and CO2 sorbent materials were developed. Successful proof-of-concept for the combined reaction-sorption process was demonstrated, which culminated in a research publication. With successful demonstration, a decision was made to switch focus to an area of fuels research of more interest to all three research institutions (CAS-NETL-PNNL). Syngas-to-Hydrocarbon Fuels through Higher Alcohol Intermediates There are two types of processes in syngas conversion to fuels that are attracting R&D interest: 1) syngas conversion to mixed alcohols; and 2) syngas conversion to gasoline via the methanol-to-gasoline process developed by Exxon-Mobil in the 1970s. The focus of this task was to develop a one-step conversion technology by effectively incorporating both processes, which is expected to reduce the capital and operational cost associated with the conversion of coal-derived syngas to liquid fuels. It should be noted that this work did not further study the classic Fischer-Tropsch reaction pathway. Rather, we focused on the studies for unique catalyst pathways that involve the direct liquid fuel synthesis enabled by oxygenated intermediates. Recent advances made in the area of higher alcohol synthesis including the novel catalytic composite materials recently developed by CAS using base metal catalysts were used.« less

Exploring the Effects of Conversational Repair as a Scaffolding Strategy to Promote Mathematics Explanations of Students with Learning Disabilities

ERIC Educational Resources Information Center

Liu, Jia

2013-01-01

Conversational repair often occurs in conversations when people attempt to address communicative breakdowns or inaccuracy by way of repeating what have been said or putting them in another way. The review of literature on conversational repair revealed that as an important concept in pragmatic aspect of language, it is an effective strategy to…

On the Performance Potential of Bioelectrochemical Life Support Systems

NASA Technical Reports Server (NTRS)

Mansell, J. Matthew

2013-01-01

An area of growing multi-disciplinary research and revolutionary development for bio-processing on Earth is bioelectrochemical systems. These systems exploit the capability of many microorganisms to act as biocatalysts, enhancing the performance of electrochemical processes which convert low-value materials into valuable products. Many varieties of such processes hold potential value for space exploration as means to recycle metabolic waste and other undesirable materials or insitu resources into oxygen, water, and other valuable substances. However, the wide range of possible reactants, products, configurations, and operating parameters, along with the early stage of development and application on the ground necessitate thorough consideration of which, if any, possibilities could outperform existing technologies and should thus receive investment for space applications. In turn, the decision depends on the theoretical and practical limits of performance and the value of the reactant-product conversions within spaceflight scenarios, and should, to the greatest extent possible, be examined from the perspective of a fully designed, integrated system, rather than as an isolated unit lacking critical components like valves and pumps. Herein, we select a series of possible reactant-product conversions, develop concept process flow diagrams for each, and estimate theoretical and (where sufficient literature data allows) practical performance limitations of each. The objective was to estimate the costs, benefits, and risks of each concept in order to aid strategic decisions in the early-phase technology development effort.

[Correlation between degree of conversion, microhardness and inorganic content in composites].

PubMed

Neves, Alisson Discacciati; Discacciati, José Augusto César; Orêfice, Rodrigo Lambert; Jansen, Wellington Corrêa

2002-01-01

The purpose of this study was to evaluate the correlation between degree of conversion and microhardness in dental composites, as well as the effect of the inorganic content and type of photo-curing unit on these parameters. Three indirect composites (Artglass, Solidex and Zeta LC) were polymerized by means of three different laboratorial units (UniXS, Solidilite and an experimental device). For each material, fifteen samples were prepared using a metal matrix. The degree of conversion was analyzed by means of infrared spectroscopy, and microhardness was also assessed. The inorganic content was measured by means of thermogravimetric analysis (TGA). The Pearson s test was carried out in order to determine correlations. The degree of conversion of Artglass ranged from 37.5% to 79.2%, and its microhardness, from 32.4 to 50.3 (r = 0.904). The degree of conversion of Solidex ranged from 41.2% to 60.4%, and its microhardness, from 33.3 to 44.1 (r = 0.707). The degree of conversion and the microhardness of Zeta LC ranged from 62.0% to 78.0% and from 22.6 to 33.6, respectively (r = 0.710). It was concluded that the utilization of different photo-curing units caused variations on the degree of conversion, as a result of specific characteristics of each unit. For each material, there was strong correlation between the degree of conversion and microhardness. In addition, when different materials were compared, microhardness was more affected by filler content than by the degree of conversion.

New Concepts for Compact Space Reactor Power Systems for Space Based Radar Applications: A Feasibility Study

DTIC Science & Technology

1989-12-01

SPENT FUEL REPROCESSING COULD ALSO BE EMPLOYED IRRADIATION EXPERIENCE - EXTREMELY LIMITED - JOINT US/UK PROGRAM (ONGOING) - TUI/KFK PROGRAM (CANCELED...only the use of off-the-shelf technologies. For example, conventional fuel technology (uranium dioxide), conventional thermionic conversion...advanced fuel (Americium oxide, A1TI2O3) and advanced thermionic conversion. Concept C involves use of an advanced fuel (Americium oxide, Arri203

Variability in Conversation Management: Fragmentation of Discourse and Back-Channel Expressions in Japanese and English.

ERIC Educational Resources Information Center

Maynard, Senko K.

The casual conversation of six pairs of Japanese and six pairs of American colleges students was analyzed for evidence of two related aspects of conversation management: the linguistic characteristics of utterance units and back-channel strategies. Utterance units are defined as those occurring between identifiable pauses or breaks in tempo.…

The elephant in the room: Dialogues about race within cross-cultural supervisory relationships.

PubMed

White-Davis, Tanya; Stein, Emma; Karasz, Alison

2016-05-01

For centuries, the concept of race, a uniquely pervasive social construct, has often complicated dialogue and interactions between groups of people. This study assessed perceptions and attitudes of faculty and trainees with varied racial backgrounds within graduate medical and psychology programs. Self-reported responses addressed potential barriers and facilitating factors required for meaningful conversations about race. A brief 18-question survey was developed and administered electronically to three professional and academic Listservs within a large metropolitan city in northeast United States. Quantitative and qualitative analysis were conducted using SPSS Statistical Software and Text analyzer. Results revealed that among participants (N = 57) a majority experienced cross-racial supervision, and more than half indicated engaging in conversations about race within supervision. Respondents endorsed lack of comfort and lack of opportunity/time as significant barriers to discussing race within supervision. When race-related dialogues occurred, a majority of supervisees and supervisors found it beneficial. Most Supervisors of Color(a) actively initiated these conversations in supervision, while White supervisees endorsed the least benefit from these conversations. Contrary to our expectations, few respondents endorsed limited training as a barrier. The current study revealed cross-racial dialogues about race may be occurring frequently in supervisory relationships. Supervisees of Color reported benefiting from these dialogues, in contrast to their White counterparts, who endorsed the least benefit. Lack of comfort in supervisory relationships appears to be a significant barrier to having these conversations. Therefore, it is important for supervisors to create supervisory relationships emphasizing safety and comfort. Directions for future research are discussed. © The Author(s) 2016.

The Recovery of Energy from Waste.

ERIC Educational Resources Information Center

Baxter, Zeland L.; And Others

This study unit advocates the use of biomass conversion techniques with municipal solid wastes as a viable action for energy development. The unit includes: (1) an introductory section (providing a unit overview and supportive statements for biomass conversion; (2) a historical review of energy use from wastes; (3) a section on design and…

Profiling of Participants in Chat Conversations Using Creativity-Based Heuristics

ERIC Educational Resources Information Center

Chiru, Costin-Gabriel; Rebedea, Traian

2017-01-01

This article proposes a new fully automated method for identifying creativity that is manifested in a divergent task. The task is represented by chat conversations in small groups, each group having to debate on the same topics, with the purpose of better understanding the discussed concepts. The chat conversations were created by undergraduate…

Order and Disorder in Conversation: Encounters with Dementia of the Alzheimer's Type

ERIC Educational Resources Information Center

Muller, Nicole; Guendouzi, Jacqueline A.

2005-01-01

After a brief introduction to Dementia of the Alzheimer's Type (DAT), its behavioral diagnostic symptom complex and a summary of communicative implications, we present data from two conversations involving participants with and without DAT. We discuss the concept of "order" in conversation, and the central importance of interactional monitoring.…

[Family members integration in patients' care in haematology units: a new application of proximology.].

PubMed

Amblard-Manhès, E; Fedor, M-C; Belgacem, B; Brugnon, D; Nore, F; Gironde, M; Bay, J-O; Hermet, R; Guyotat, D; Bezy, O; Gerbaud, L; Tournilhac, O

2009-09-01

Hospitalization per se is a stress for the family members of a loved one. While their role as informal caregivers is well known with at home patients, especially in oncology, they usually are only mere visitors at the hospital. Hence the integration of family members of in patients' care might improve both patients and families' quality of life. Such a supportive care concept has been previously investigated in pediatric, neurology and intensive care units, but there is not such data in hematology although the therapeutic in this field is marked by long-term stay in hospitals' rooms. Since 2001, we developed in Clermont-Ferrand University hospital such a project of integration. Put together, the literature data and our first results (opinion poll) show that the main risk of this approach is the exhaustion of family caregivers, their fear of miss conduct and the alteration of the relationship they previously had with the patient. Conversely this approach is likely beneficial in improving both patients and family member's experience during hospitalization in lowering both patients' affective social and may be cultural loneliness and family members' feeling of uselessly and guilt. In France the development of supportive care and therapeutic education in oncology is nowadays encouraged and of there is no legal basis to restrain the development of this concept. Whose concept, nevertheless should be carefully set up and studied and its benefit remain to be clearly demonstrated.

Ten Essential Concepts for Remediation in Mathematics.

ERIC Educational Resources Information Center

Roseman, Louis

1985-01-01

Ten crucial mathematical concepts with which errors are made are listed, with methods used to teach them to high school students. The concepts concern order, place values, inverse operations, multiplication and division, remainders, identity elements, fractions, conversions, decimal points, and percentages. (MNS)

Light harvesting for quantum solar energy conversion

NASA Astrophysics Data System (ADS)

Markvart, Tomas

2000-05-01

Despite wide structural and functional differences, the laws that govern quantum solar energy conversion to chemical energy or electricity share many similarities. In the photosynthetic membrane, in common with semiconductor solar cells, the conversion process proceeds from the creation of electron-hole pairs by a photon of light, followed by charge separation to produce the required high-energy product. In many cases, however, mechanisms are needed to enhance the optical absorption cross-section and extend the spectral range of operation. A common way of achieving this is by light harvesting: light absorption by a specialised unit which transfers the energy to the conversion apparatus. This paper considers two examples of light harvesting - semiconductor solar cells and the photosynthetic apparatus - to illustrate the basic operation and principles that apply. The existence of a light harvesting unit in photosynthesis has been known since the early 1930's but details of the process - relating, in particular, to the relationship between the structure and spectral properties - are still being unravelled. The excitation energy carriers are excitons but the precise nature of the transport - via the solid state Frenkel-Peierls variety or by Förster's resonant energy transfer - is still subject to debate. In semiconductor solar cells, the energy of the absorbed photon is collected by minority carriers but the broad principles remain the same. In both cases it is shown that the rate of energy conversion is described by a law which parallels the Shockley's solar cell equation, and the light harvesting energy collection is subject to reciprocity relations which resemble Onsager's reciprocity relations between coefficients which couple appropriate forces and flows in non-equilibrium thermodynamics. Differences in the basic atomic make-up in the two systems lead to different energy transport equations. In both cases, however, similar mathematical techniques based on Green's functions can be used to advantage. The Green's function provides a convenient vehicle for the determination of the probability of energy collection - known as the trapping probability in the photosynthetic unit. Using the reciprocity relation, both quantities are shown to be closely related to the distribution of the energy carriers in the dark. The collection probability can then be discussed in detail, by solving the semiconductor device equations in the case of solar cell, and by linking the Green's function formalism to the random walk model in the case of the photosynthetic unit. The concept of resonant energy transfer is beginning to enter the arena of solid-state optoelectronics. It is an aim of this paper to show that similar phenomena - which exist in the domain of bioenergetics - can throw new light on a range of energy transfer and collection processes that are of considerable importance in many modern optoelectronic devices.

Self-concept mediate the relationship between childhood maltreatment and abstinence motivation as well as self-efficacy among drug addicts.

PubMed

Lu, Feng-Ying; Wen, Si; Deng, Gang; Tang, Yung-Lung

2017-05-01

Childhood maltreatment is widely accepted as a risk factor for drug addiction from adolescence to adulthood. However, the influence of childhood maltreatment on drug treatment related variables, such as drug abstinence motivation and self-concept, as well as self-efficacy, remains unclear. This study aims at exploring whether self-concept mediates the relationship between childhood maltreatment and abstinence motivation, as well as self-efficacy, among drug addicts. This study involves 816 (550 males, 226 females, mean age=34.59, range=16-58 years) drug addicts from compulsory detoxification units. Participants completed questionnaires, including the childhood trauma questionnaire 28 - item short form (CTQ - SF), Tennessee self-concept scale (TSCS), general self-efficacy scale (GSES), and drug abstinence motivation questionnaire (DAMQ). The structural equation model (SEM) analysis, including total and specific forms of maltreatment scores, showed that childhood maltreatment was negatively associated with self-concept, self-efficacy, and abstinence motivation. Self-concept was positively associated with self-efficacy and abstinence motivation. Conversely, significant association between self-efficacy and abstinence motivation did not exist. An indirect analysis showed that self-concept mediated the relationship between childhood maltreatment and self-efficacy. Critically, self-concept arbitrated the relationship between childhood maltreatment and abstinence motivation. The indirect effect of self-concept between childhood maltreatment and abstinence motivation still existed when the total scores of maltreatment were replaced by the scores of specific forms of maltreatment. These results demonstrated that self-concept is a critical factor in understanding the relationship between childhood maltreatment and abstinence motivation, as well as self-efficacy, among drug addicts. Improving the sense of self-worth may be an effective intervention therapy among drug addicts with childhood maltreatment history. Copyright © 2017 Elsevier Ltd. All rights reserved.

Continuing Spanish in Grade Four: MLA Teacher's Guide. A Course of Study Including Methods, Materials, and Aids for Teaching Conversational Spanish to Fourth-Grade Children.

ERIC Educational Resources Information Center

Thompson, Mary P.; And Others

This is the second volume in a series of texts in a conversational Spanish course for elementary school children. Fourteen basic units present introductory linguistic patterns and cultural insights into the lives of the Spanish people. They include: (1) Review Unit 1, (2) Review Unit 2, (3) Special Unit A--"Cristobal Colon," (4) Review Unit 3, (5)…

Online Scholarly Conversations in General Education Astronomy Courses

NASA Astrophysics Data System (ADS)

Cai, Qijie; Wong, Ka-Wah

2018-01-01

In general education astronomy courses, many students are struggling with understanding the foundational concepts and theories in astronomy. One of the possible reasons is that, due the large class size, many of the courses are taught using a lecture mode, where human interactions and active learning are limited (Freeman et al., 2014). To address this challenge, we have applied the knowledge building framework (Scardamalia & Bereiter, 2006) to design an online collaborative learning component, called Scholarly Conversations, to be integrated into a general education astronomy course at a public, comprehensive university.During Scholarly Conversations, students are treated as scholars to advance knowledge frontiers (Scardamalia & Bereiter, 2006). The whole process involves the creation of new ideas and requires discourse and collective work for the advancement and creation of artifacts, such as theories and models (van Aalst, 2009). Based on the knowledge building principles (Scardamalia, 2002; Zhang, Scardamalia, Reeve, & Messina, 2009), several features have been built into Scholarly Conversations so that students are guided to deepen understanding of the astronomy concepts through three phases: knowledge sharing, knowledge construction and knowledge building, and reflections on learning growth (van Aalst, 2009; Cai, 2017). The online Scholarly Conversation is an extension of the lecture component of the general education astronomy course. It promotes student interactions and collaborative learning, and provides scaffolds for students to construct meanings of the essential concepts in astronomy through social learning and online technology. In this presentation, we will explain the specific design principles of the online Scholarly Conversation, and share the artifacts created to facilitate the online conversations in an general education astronomy course.Note: This project has been supported by the College of Education Research Grant Program at Minnesota State University, Mankato.

Internationalization in an Occupational Therapy Curriculum: A Philippine-American Pilot Collaboration.

PubMed

Cabatan, Maria Concepcion C; Grajo, Lenin C

This study is a pilot implementation of an Internationalization at Home (IaH) teaching and learning collaboration to enhance intercultural learning and understanding of concepts of occupation in two cohorts of occupational science and occupational therapy students from the Philippines and the United States. In this collective case study, 149 students (Cohort 1, n = 65; Cohort 2, n = 84) participated. The collaboration included virtual conversations among students, faculty presentations, reflective assignments, and completion of an anonymous online survey. Analysis yielded three essential themes: (1) perception of increased knowledge about human occupation and the influence of culture, (2) identification of teaching-learning aspects that facilitated intercultural learning outcomes, and (3) identification of factors that were enablers of and barriers to learning. This study provides insights on how intercultural learning experiences can be integrated into occupational science and occupational therapy curricula and can increase understanding of concepts related to human occupation. Copyright © 2017 by the American Occupational Therapy Association, Inc.

Rosetta Stones for Energy Problems.

ERIC Educational Resources Information Center

Hayden, Howard C.

1981-01-01

Demonstrates, using specific problems, how various energy units can be converted to joules and power units to watts. Conversion tables are provided for power, energy, generation values, thermal insulation, consumption values, sunlight, with tables also on metric prefixes and time conversions. (SK)

Revised Mulliken Electronegativities I. Calculation and Conversion to Pauling Units.

ERIC Educational Resources Information Center

Bratsch, Steven G.

1988-01-01

Discusses a revision and extension of the Mulliken electronegativity scale to consider 50 elements. Describes the calculation of valence-state promotion energies and Mulliken atomic electronegativities and the conversion of Mulliken electronegativities to Pauling units. (CW)

Reading for Integration, Identifying Complementary Threshold Concepts: The ACRL "Framework" in Conversation with "Naming What We Know: Threshold Concepts of Writing"

ERIC Educational Resources Information Center

Johnson, Brittney; McCracken, I. Moriah

2016-01-01

In 2015, threshold concepts formed the foundation of two disciplinary documents: The "ACRL Framework for Information Literacy" (2015) and "Naming What We Know: Threshold Concepts of Writing Studies" (2015). While there is no consensus in the fields about the value of threshold concepts in teaching, reading the six Frames in the…

Symposium on the Physical Chemistry of Solar Energy Conversion, Indianapolis American Chemical Society Meetings, Fall 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lian, Tianquan

2013-09-20

The Symposium on the Physical Chemistry of Solar Energy Conversion at the Fall ACS Meeting in Indianapolis, IN (Sept. 8-12) featured the following sessions (approx. 6 speakers per session): (1) Quantum Dots and Nanorods for Solar Energy Conversion (2 half-day sessions); (2) Artificial Photosynthesis: Water Oxidation; (3) Artificial Photosynthesis: Solar Fuels (2 half-day sessions); (4) Organic Solar Cells; (5) Novel Concepts for Solar Energy Conversion (2 half-day sessions); (6) Emerging Techniques for Solar Energy Conversion; (7) Interfacial Electron Transfer

24 CFR 972.103 - Definition of “conversion.”

Code of Federal Regulations, 2011 CFR

2011-04-01

... DEVELOPMENT CONVERSION OF PUBLIC HOUSING TO TENANT-BASED ASSISTANCE Required Conversion of Public Housing Developments Purpose; Definition of Conversion § 972.103 Definition of “conversion.” For purposes of this subpart, the term “conversion” means the removal of public housing units from the inventory of a PHA, and...

24 CFR 972.103 - Definition of “conversion.”

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVELOPMENT CONVERSION OF PUBLIC HOUSING TO TENANT-BASED ASSISTANCE Required Conversion of Public Housing Developments Purpose; Definition of Conversion § 972.103 Definition of “conversion.” For purposes of this subpart, the term “conversion” means the removal of public housing units from the inventory of a PHA, and...

24 CFR 972.203 - Definition of “conversion.”

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVELOPMENT CONVERSION OF PUBLIC HOUSING TO TENANT-BASED ASSISTANCE Voluntary Conversion of Public Housing Developments Purpose; Definition of Conversion § 972.203 Definition of “conversion.” For purposes of this subpart, the term “conversion” means the removal of public housing units from the inventory of a Public...

24 CFR 972.203 - Definition of “conversion.”

Code of Federal Regulations, 2011 CFR

2011-04-01

... DEVELOPMENT CONVERSION OF PUBLIC HOUSING TO TENANT-BASED ASSISTANCE Voluntary Conversion of Public Housing Developments Purpose; Definition of Conversion § 972.203 Definition of “conversion.” For purposes of this subpart, the term “conversion” means the removal of public housing units from the inventory of a Public...

Concept maps: A tool for knowledge management and synthesis in web-based conversational learning.

PubMed

Joshi, Ankur; Singh, Satendra; Jaswal, Shivani; Badyal, Dinesh Kumar; Singh, Tejinder

2016-01-01

Web-based conversational learning provides an opportunity for shared knowledge base creation through collaboration and collective wisdom extraction. Usually, the amount of generated information in such forums is very huge, multidimensional (in alignment with the desirable preconditions for constructivist knowledge creation), and sometimes, the nature of expected new information may not be anticipated in advance. Thus, concept maps (crafted from constructed data) as "process summary" tools may be a solution to improve critical thinking and learning by making connections between the facts or knowledge shared by the participants during online discussion This exploratory paper begins with the description of this innovation tried on a web-based interacting platform (email list management software), FAIMER-Listserv, and generated qualitative evidence through peer-feedback. This process description is further supported by a theoretical construct which shows how social constructivism (inclusive of autonomy and complexity) affects the conversational learning. The paper rationalizes the use of concept map as mid-summary tool for extracting information and further sense making out of this apparent intricacy.

A Small Fission Power System with Stirling Power Conversion for NASA Science Missions

NASA Technical Reports Server (NTRS)

Mason, Lee; Carmichael, Chad

2011-01-01

In early 2010, a joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) study team developed a concept for a 1 kWe Fission Power System with a 15-year design life that could be available for a 2020 launch to support future NASA science missions. The baseline concept included a solid block uranium-molybdenum reactor core with embedded heat pipes and distributed thermoelectric converters directly coupled to aluminum radiator fins. A short follow-on study was conducted at NASA Glenn Research Center (GRC) to evaluate an alternative power conversion approach. The GRC study considered the use of free-piston Stirling power conversion as a substitution to the thermoelectric converters. The resulting concept enables a power increase to 3 kWe with the same reactor design and scalability to 10 kW without changing the reactor technology. This paper presents the configuration layout, system performance, mass summary, and heat transfer analysis resulting from the study.

Light-triggered thermoelectric conversion based on a carbon nanotube-polymer hybrid gel.

PubMed

Miyako, Eijiro; Nagata, Hideya; Funahashi, Ryoji; Hirano, Ken; Hirotsu, Takahiro

2009-01-01

Lights? Nanotubes? Action! A hydrogel comprising lysozymes, poly(ethylene glycol), phospholipids, and functionalized single-walled carbon nanotubes is employed for light-driven thermoelectric conversion. A photoinduced thermoelectric conversion module based on the hydrogel functions as a novel electric power generator (see image). This concept may find application in various industries, such as robotics and aerospace engineering.

Dynamic modelling and simulation of CSP plant based on supercritical carbon dioxide closed Brayton cycle

NASA Astrophysics Data System (ADS)

Hakkarainen, Elina; Sihvonen, Teemu; Lappalainen, Jari

2017-06-01

Supercritical carbon dioxide (sCO2) has recently gained a lot of interest as a working fluid in different power generation applications. For concentrated solar power (CSP) applications, sCO2 provides especially interesting option if it could be used both as the heat transfer fluid (HTF) in the solar field and as the working fluid in the power conversion unit. This work presents development of a dynamic model of CSP plant concept, in which sCO2 is used for extracting the solar heat in Linear Fresnel collector field, and directly applied as the working fluid in the recuperative Brayton cycle; these both in a single flow loop. We consider the dynamic model is capable to predict the system behavior in typical operational transients in a physically plausible way. The novel concept was tested through simulation cases under different weather conditions. The results suggest that the concept can be successfully controlled and operated in the supercritical region to generate electric power during the daytime, and perform start-up and shut down procedures in order to stay overnight in sub-critical conditions. Besides the normal daily operation, the control system was demonstrated to manage disturbances due to sudden irradiance changes.

Magnetic energy storage and conversion in the solar atmosphere

NASA Technical Reports Server (NTRS)

Spicer, D. S.; Mariska, J. T.; Boris, J. P.

1986-01-01

According to the approach employed in this investigation, particularly important simple configurations of magnetic field and plasma are identified, and it is attempted to achieve an understanding of the large-scale dynamic processes and transformations which these systems can undergo. Fundamental concepts are discussed, taking into account aspects of magnetic energy generation, ideal MHD theory, non-MHD properties, the concept of 'anomalous' resistivity, and global electrodynamic coupling. Questions of magnetically controlled energy conversion are examined, giving attention to magnetic modifications of plasma transport, the transition region structure and flows, channeling and acceleration of plasma, channeling and dissipation of MHD waves, and anomalous dissipation of field-aligned currents. A description of the characteristics of magnetohydrodynamic energy conversion is also provided, and outstanding questions are discussed.

A new strategy for efficient solar energy conversion: Parallel-processing with surface plasmons

NASA Technical Reports Server (NTRS)

Anderson, L. M.

1982-01-01

This paper introduces an advanced concept for direct conversion of sunlight to electricity, which aims at high efficiency by tailoring the conversion process to separate energy bands within the broad solar spectrum. The objective is to obtain a high level of spectrum-splitting without sequential losses or unique materials for each frequency band. In this concept, sunlight excites a spectrum of surface plasma waves which are processed in parallel on the same metal film. The surface plasmons transport energy to an array of metal-barrier-semiconductor diodes, where energy is extracted by inelastic tunneling. Diodes are tuned to different frequency bands by selecting the operating voltage and geometry, but all diodes share the same materials.

Metrication and AIHA.

PubMed

Burnett, R D

1977-05-01

AIHA supports a planned orderly national program for conversion to the metric system and will cooperate with other technical societies and organizations in implementing this voluntary conversion. The Association will use the International System of Units (SI) as modified by the Secretary of Commerce for use in the United States in all official publications, papers and documents. U.S. customary units can be presented in parentheses following the appropriate SI unit, when it is necessary for clarity.

Mechanochemical Energy Conversion

ERIC Educational Resources Information Center

Pines, E.; And Others

1973-01-01

Summarizes the thermodynamics of macromolecular systems, including theories and experiments of cyclic energy conversion with rubber and collagen as working substances. Indicates that an early introduction into the concept of chemical potential and solution thermodynamics is made possible through the study of the cyclic processes. (CC)

Megawatt Class Nuclear Space Power Systems (MCNSPS) conceptual design and evaluation report. Volume 1: Objectives, summary results and introduction

NASA Technical Reports Server (NTRS)

Wetch, J. R.

1988-01-01

The objective was to determine which reactor, conversion, and radiator technologies would best fulfill future Megawatt Class Nuclear Space Power System Requirements. Specifically, the requirement was 10 megawatts for 5 years of full power operation and 10 years systems life on orbit. A variety of liquid metal and gas cooled reactors, static and dynamic conversion systems, and passive and dynamic radiators were considered. Four concepts were selected for more detailed study. The concepts are: a gas cooled reactor with closed cycle Brayton turbine-alternator conversion with heat pipe and pumped tube-fin heat rejection; a lithium cooled reactor with a free piston Stirling engine-linear alternator and a pumped tube-fin radiator; a lithium cooled reactor with potassium Rankine turbine-alternator and heat pipe radiator; and a lithium cooled incore thermionic static conversion reactor with a heat pipe radiator. The systems recommended for further development to meet a 10 megawatt long life requirement are the lithium cooled reactor with the K-Rankine conversion and heat pipe radiator, and the lithium cooled incore thermionic reactor with heat pipe radiator.

Thermionic/AMTEC cascade converter concept for high-efficiency space power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hagan, T.H. van; Smith, J.N. Jr.; Schuller, M.

1996-12-31

This paper presents trade studies that address the use of the thermionic/AMTEC cell--a cascaded, high-efficiency, static power conversion concept that appears well-suited to space power applications. Both the thermionic and AMTEC power conversion approaches have been shown to be promising candidates for space power. Thermionics offers system compactness via modest efficiency at high heat rejection temperatures, and AMTEC offers high efficiency at modest heat rejection temperature. From a thermal viewpoint the two are ideally suited for cascaded power conversion: thermionic heat rejection and AMTEC heat source temperatures are essentially the same. In addition to realizing conversion efficiencies potentially as highmore » as 35--40%, such a cascade offers the following perceived benefits: survivability; simplicity; technology readiness; and technology growth. Mechanical approaches and thermal/electric matching criteria for integrating thermionics and AMTEC into a single conversion device are described. Focusing primarily on solar thermal space power applications, parametric trends are presented to show the performance and cost potential that should be achievable with present-day technology in cascaded thermionic/AMTEC systems.« less

Conversion coefficients for determination of dispersed photon dose during radiotherapy: NRUrad input code for MCNP.

PubMed

Shahmohammadi Beni, Mehrdad; Ng, C Y P; Krstic, D; Nikezic, D; Yu, K N

2017-01-01

Radiotherapy is a common cancer treatment module, where a certain amount of dose will be delivered to the targeted organ. This is achieved usually by photons generated by linear accelerator units. However, radiation scattering within the patient's body and the surrounding environment will lead to dose dispersion to healthy tissues which are not targets of the primary radiation. Determination of the dispersed dose would be important for assessing the risk and biological consequences in different organs or tissues. In the present work, the concept of conversion coefficient (F) of the dispersed dose was developed, in which F = (Dd/Dt), where Dd was the dispersed dose in a non-targeted tissue and Dt is the absorbed dose in the targeted tissue. To quantify Dd and Dt, a comprehensive model was developed using the Monte Carlo N-Particle (MCNP) package to simulate the linear accelerator head, the human phantom, the treatment couch and the radiotherapy treatment room. The present work also demonstrated the feasibility and power of parallel computing through the use of the Message Passing Interface (MPI) version of MCNP5.

Conversion coefficients for determination of dispersed photon dose during radiotherapy: NRUrad input code for MCNP

PubMed Central

Krstic, D.; Nikezic, D.

2017-01-01

Radiotherapy is a common cancer treatment module, where a certain amount of dose will be delivered to the targeted organ. This is achieved usually by photons generated by linear accelerator units. However, radiation scattering within the patient’s body and the surrounding environment will lead to dose dispersion to healthy tissues which are not targets of the primary radiation. Determination of the dispersed dose would be important for assessing the risk and biological consequences in different organs or tissues. In the present work, the concept of conversion coefficient (F) of the dispersed dose was developed, in which F = (Dd/Dt), where Dd was the dispersed dose in a non-targeted tissue and Dt is the absorbed dose in the targeted tissue. To quantify Dd and Dt, a comprehensive model was developed using the Monte Carlo N-Particle (MCNP) package to simulate the linear accelerator head, the human phantom, the treatment couch and the radiotherapy treatment room. The present work also demonstrated the feasibility and power of parallel computing through the use of the Message Passing Interface (MPI) version of MCNP5. PMID:28362837

Implications of metric conversion.

PubMed

Laros, R K

1980-11-01

The international scientific community is rapidly achieving conversion to the metric system, and the Système International (SI system) has been chosen for use by health scientists. Because the United States remains 1 of only 4 countries not now using part or all of the SI system, there is now a systematic effort toward rapid conversion. Although most of the SI system is not controversial, several SI units are highly so. Examples include joules instead of calories, pascals instead of millimeters of mercury, and moles per liter instead of milligrams per 100 milliliters. Obstetrician-gynecologists need to be familiar with the SI units and to voice their feelings about the various controversial units. There are decisions still to be made, and the time for discussion and advice is now.

Conversion system overview assessment. Volume 1: solar thermoelectrics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jayadev, T. S.; Henderson, J.; Finegold, J.

1979-08-01

An assessment of thermoelectrics for solar energy conversion is given. There is significant potential for solar thermoelectrics in solar technologies where collector costs are low; e.g., Ocean Thermal Energy Conversion (OTEC) and solar ponds. Reports of two studies by manufacturers assessing the cost of thermoelectric generators in large scale production are included in the appendix and several new concepts thermoelectric systems are presented. (WHK)

Approach for Text Classification Based on the Similarity Measurement between Normal Cloud Models

PubMed Central

Dai, Jin; Liu, Xin

2014-01-01

The similarity between objects is the core research area of data mining. In order to reduce the interference of the uncertainty of nature language, a similarity measurement between normal cloud models is adopted to text classification research. On this basis, a novel text classifier based on cloud concept jumping up (CCJU-TC) is proposed. It can efficiently accomplish conversion between qualitative concept and quantitative data. Through the conversion from text set to text information table based on VSM model, the text qualitative concept, which is extraction from the same category, is jumping up as a whole category concept. According to the cloud similarity between the test text and each category concept, the test text is assigned to the most similar category. By the comparison among different text classifiers in different feature selection set, it fully proves that not only does CCJU-TC have a strong ability to adapt to the different text features, but also the classification performance is also better than the traditional classifiers. PMID:24711737

Systems for Teaching Complex Texts: A Proof-of-Concept Investigation

ERIC Educational Resources Information Center

Fisher, Douglas; Frey, Nancy

2016-01-01

In this article we investigate the systems that need to be in place for students to learn from increasingly complex texts. Our concept, drawn from past research, includes clear learning targets, teacher modeling, collaborative conversations, close reading, small group reading, and wide reading. Using a "proof of concept" model, we follow…

An Overview of Space Power Systems for NASA Missions

NASA Technical Reports Server (NTRS)

Lyons, Valerie J.; Scott, John H.

2007-01-01

Power is a critical commodity for all engineering efforts and is especially challenging in the aerospace field. This paper will provide a broad brush overview of some of the immediate and important challenges to NASA missions in the field of aerospace power, for generation, energy conversion, distribution, and storage. NASA s newest vehicles which are currently in the design phase will have power systems that will be developed from current technology, but will have the challenges of being light-weight, energy-efficient, and space-qualified. Future lunar and Mars "outposts" will need high power generation units for life support and energy-intensive exploration efforts. An overview of the progress in concepts for power systems and the status of the required technologies are discussed.

Space power for space

NASA Technical Reports Server (NTRS)

Mullin, J. P.

1978-01-01

The total energy demanded by space missions of the future is expected to exceed past needs by orders of magnitude. The unit costs of this energy must be reduced from present levels if these missions are to be carried out at projected budget levels. The broad employment of electric propulsion and the capability to utilize novel high power sensors hinge on the availability of systems lighter by factors of ten or more than have flown to date. The NASA program aimed at providing the technological basis to meet these demands is described in this paper. Research and technology efforts in areas of energy conversion, storage and management are covered. In addition, work aimed at evolving the understanding necessary to cope with space environment interactions and at advanced concepts is described.

New literacies, multiple literacies, unlimited literacies: what now, what next, where to? A response to blue listerine, parochialism and ASL literacy.

PubMed

Paul, Peter V

2006-01-01

This article is a response to Blue Listerine, Parochialism, and ASL Literacy (Czubek, 2006). The author presents his views on the concepts of literacy and the new and multiple literacies. In addition, the merits of print literacy and other types of literacies are discussed. Although the author agrees that there is an American Sign Language (ASL) literacy, he maintains that there should be a distinction between conversational "literacy" forms (speech and sign) and secondary literacy forms (reading and writing). It might be that cognitive skills associated with print literacy and, possibly, other captured literacy forms, are necessary for a technological, scientific-driven society such as that which exists in the United States.

Asymmetric wave transmission in a diatomic acoustic/elastic metamaterial

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Bing; Tan, K. T., E-mail: ktan@uakron.edu

2016-08-21

Asymmetric acoustic/elastic wave transmission has recently been realized using nonlinearity, wave diffraction, or bias effects, but always at the cost of frequency distortion, direction shift, large volumes, or external energy. Based on the self-coupling of dual resonators, we propose a linear diatomic metamaterial, consisting of several small-sized unit cells, to realize large asymmetric wave transmission in low frequency domain (below 1 kHz). The asymmetric transmission mechanism is theoretically investigated, and numerically verified by both mass-spring and continuum models. This passive system does not require any frequency conversion or external energy, and the asymmetric transmission band can be theoretically predicted andmore » mathematically controlled, which extends the design concept of unidirectional transmission devices.« less

Advanced Concepts: Aneutronic Fusion Power and Propulsion

NASA Technical Reports Server (NTRS)

Chapman, John J.

2012-01-01

Aneutronic Fusion for In-Space thrust, power. Clean energy & potential nuclear gains. Fusion plant concepts, potential to use advanced fuels. Methods to harness ionic momentum for high Isp thrust plus direct power conversion into electricity will be presented.

Basic and applied research related to the technology of space energy conversion systems, 1982 - 1983

NASA Technical Reports Server (NTRS)

Hertzberg, A.

1983-01-01

Topics on solar energy conversion concepts and applications are discussed. An overview of the current status and future utilization of radiation receivers for electrical energy generation, liquid droplet radiation systems, and liquid droplet heat exchangers is presented.

Exhaust gas purification system for lean burn engine

DOEpatents

Haines, Leland Milburn

2002-02-19

An exhaust gas purification system for a lean burn engine includes a thermal mass unit and a NO.sub.x conversion catalyst unit downstream of the thermal mass unit. The NO.sub.x conversion catalyst unit includes at least one catalyst section. Each catalyst section includes a catalytic layer for converting NO.sub.x coupled to a heat exchanger. The heat exchanger portion of the catalyst section acts to maintain the catalytic layer substantially at a desired temperature and cools the exhaust gas flowing from the catalytic layer into the next catalytic section in the series. In a further aspect of the invention, the exhaust gas purification system includes a dual length exhaust pipe upstream of the NO.sub.x conversion catalyst unit. The dual length exhaust pipe includes a second heat exchanger which functions to maintain the temperature of the exhaust gas flowing into the thermal mass downstream near a desired average temperature.

Catalysis of heat-to-work conversion in quantum machines

PubMed Central

Ghosh, A.; Latune, C. L.; Davidovich, L.; Kurizki, G.

2017-01-01

We propose a hitherto-unexplored concept in quantum thermodynamics: catalysis of heat-to-work conversion by quantum nonlinear pumping of the piston mode which extracts work from the machine. This concept is analogous to chemical reaction catalysis: Small energy investment by the catalyst (pump) may yield a large increase in heat-to-work conversion. Since it is powered by thermal baths, the catalyzed machine adheres to the Carnot bound, but may strongly enhance its efficiency and power compared with its noncatalyzed counterparts. This enhancement stems from the increased ability of the squeezed piston to store work. Remarkably, the fraction of piston energy that is convertible into work may then approach unity. The present machine and its counterparts powered by squeezed baths share a common feature: Neither is a genuine heat engine. However, a squeezed pump that catalyzes heat-to-work conversion by small investment of work is much more advantageous than a squeezed bath that simply transduces part of the work invested in its squeezing into work performed by the machine. PMID:29087326

Catalysis of heat-to-work conversion in quantum machines

NASA Astrophysics Data System (ADS)

Ghosh, A.; Latune, C. L.; Davidovich, L.; Kurizki, G.

2017-11-01

We propose a hitherto-unexplored concept in quantum thermodynamics: catalysis of heat-to-work conversion by quantum nonlinear pumping of the piston mode which extracts work from the machine. This concept is analogous to chemical reaction catalysis: Small energy investment by the catalyst (pump) may yield a large increase in heat-to-work conversion. Since it is powered by thermal baths, the catalyzed machine adheres to the Carnot bound, but may strongly enhance its efficiency and power compared with its noncatalyzed counterparts. This enhancement stems from the increased ability of the squeezed piston to store work. Remarkably, the fraction of piston energy that is convertible into work may then approach unity. The present machine and its counterparts powered by squeezed baths share a common feature: Neither is a genuine heat engine. However, a squeezed pump that catalyzes heat-to-work conversion by small investment of work is much more advantageous than a squeezed bath that simply transduces part of the work invested in its squeezing into work performed by the machine.

Catalysis of heat-to-work conversion in quantum machines.

PubMed

Ghosh, A; Latune, C L; Davidovich, L; Kurizki, G

2017-11-14

We propose a hitherto-unexplored concept in quantum thermodynamics: catalysis of heat-to-work conversion by quantum nonlinear pumping of the piston mode which extracts work from the machine. This concept is analogous to chemical reaction catalysis: Small energy investment by the catalyst (pump) may yield a large increase in heat-to-work conversion. Since it is powered by thermal baths, the catalyzed machine adheres to the Carnot bound, but may strongly enhance its efficiency and power compared with its noncatalyzed counterparts. This enhancement stems from the increased ability of the squeezed piston to store work. Remarkably, the fraction of piston energy that is convertible into work may then approach unity. The present machine and its counterparts powered by squeezed baths share a common feature: Neither is a genuine heat engine. However, a squeezed pump that catalyzes heat-to-work conversion by small investment of work is much more advantageous than a squeezed bath that simply transduces part of the work invested in its squeezing into work performed by the machine.

Continuing Spanish in Grade Five: MLA Teacher's Guide. A Course of Study Including Methods, Materials, and Aids for Teaching Conversational Spanish to Fifth-Grade Children.

ERIC Educational Resources Information Center

Thompson, Mary P.; And Others

This is the third volume in a series of texts in a conversational Spanish course for elementary school children. Nine basic units present introductory linguistic patterns and cultural insights into the lives of the Spanish people. They include: (1) Review Unit 1, ("Cristobal Colon"), (2) Review Unit 2, (3) "Un Accidente,""La Navidad," and…

Computer Controlled Microwave Oven System for Rapid Water Content Determination

DTIC Science & Technology

1988-11-01

Codes - .d/or CONTENTS Page PREFACE .................................................................... 1 CONVERSION FACTORS, NON- SI TO SI (METRIC...CONVERSION FACTORS, NON- SI TO SI (METRIC) UNITS OF MEASUREMENT Non- SI units of measurement used in this report can be converted to SI (metric) units as...formula: C = (5/9)(F - 32) . To obtain Kelvin ( K ) readings, use: K = (5/9)(F - 32) + 273.15 3 COMPUTER CONTROLLED MICROWAVE OVEN SYSTEM FOR RAPID WATER

5 CFR 870.1007 - Termination and conversion.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 2 2011-01-01 2011-01-01 false Termination and conversion. 870.1007... Iraq and Kuwait and United States Hostages Captured in Lebanon § 870.1007 Termination and conversion... the 31-day extension of coverage and conversion as set forth in subpart F of this part, unless the...

5 CFR 870.1007 - Termination and conversion.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Termination and conversion. 870.1007... Iraq and Kuwait and United States Hostages Captured in Lebanon § 870.1007 Termination and conversion... the 31-day extension of coverage and conversion as set forth in subpart F of this part, unless the...

47 CFR 80.761 - Conversion graphs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Conversion graphs. 80.761 Section 80.761... MARITIME SERVICES Standards for Computing Public Coast Station VHF Coverage § 80.761 Conversion graphs. The following graphs must be employed where conversion from one to the other of the indicated types of units is...

47 CFR 80.761 - Conversion graphs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Conversion graphs. 80.761 Section 80.761... MARITIME SERVICES Standards for Computing Public Coast Station VHF Coverage § 80.761 Conversion graphs. The following graphs must be employed where conversion from one to the other of the indicated types of units is...

Roadmap on optical energy conversion

NASA Astrophysics Data System (ADS)

Boriskina, Svetlana V.; Green, Martin A.; Catchpole, Kylie; Yablonovitch, Eli; Beard, Matthew C.; Okada, Yoshitaka; Lany, Stephan; Gershon, Talia; Zakutayev, Andriy; Tahersima, Mohammad H.; Sorger, Volker J.; Naughton, Michael J.; Kempa, Krzysztof; Dagenais, Mario; Yao, Yuan; Xu, Lu; Sheng, Xing; Bronstein, Noah D.; Rogers, John A.; Alivisatos, A. Paul; Nuzzo, Ralph G.; Gordon, Jeffrey M.; Wu, Di M.; Wisser, Michael D.; Salleo, Alberto; Dionne, Jennifer; Bermel, Peter; Greffet, Jean-Jacques; Celanovic, Ivan; Soljacic, Marin; Manor, Assaf; Rotschild, Carmel; Raman, Aaswath; Zhu, Linxiao; Fan, Shanhui; Chen, Gang

2016-07-01

For decades, progress in the field of optical (including solar) energy conversion was dominated by advances in the conventional concentrating optics and materials design. In recent years, however, conceptual and technological breakthroughs in the fields of nanophotonics and plasmonics combined with a better understanding of the thermodynamics of the photon energy-conversion processes reshaped the landscape of energy-conversion schemes and devices. Nanostructured devices and materials that make use of size quantization effects to manipulate photon density of states offer a way to overcome the conventional light absorption limits. Novel optical spectrum splitting and photon-recycling schemes reduce the entropy production in the optical energy-conversion platforms and boost their efficiencies. Optical design concepts are rapidly expanding into the infrared energy band, offering new approaches to harvest waste heat, to reduce the thermal emission losses, and to achieve noncontact radiative cooling of solar cells as well as of optical and electronic circuitries. Light-matter interaction enabled by nanophotonics and plasmonics underlie the performance of the third- and fourth-generation energy-conversion devices, including up- and down-conversion of photon energy, near-field radiative energy transfer, and hot electron generation and harvesting. Finally, the increased market penetration of alternative solar energy-conversion technologies amplifies the role of cost-driven and environmental considerations. This roadmap on optical energy conversion provides a snapshot of the state of the art in optical energy conversion, remaining challenges, and most promising approaches to address these challenges. Leading experts authored 19 focused short sections of the roadmap where they share their vision on a specific aspect of this burgeoning research field. The roadmap opens up with a tutorial section, which introduces major concepts and terminology. It is our hope that the roadmap will serve as an important resource for the scientific community, new generations of researchers, funding agencies, industry experts, and investors.

CFD Extraction Tool for TecPlot From DPLR Solutions

NASA Technical Reports Server (NTRS)

Norman, David

2013-01-01

This invention is a TecPlot macro of a computer program in the TecPlot programming language that processes data from DPLR solutions in TecPlot format. DPLR (Data-Parallel Line Relaxation) is a NASA computational fluid dynamics (CFD) code, and TecPlot is a commercial CFD post-processing tool. The Tec- Plot data is in SI units (same as DPLR output). The invention converts the SI units into British units. The macro modifies the TecPlot data with unit conversions, and adds some extra calculations. After unit conversions, the macro cuts a slice, and adds vectors on the current plot for output format. The macro can also process surface solutions. Existing solutions use manual conversion and superposition. The conversion is complicated because it must be applied to a range of inter-related scalars and vectors to describe a 2D or 3D flow field. It processes the CFD solution to create superposition/comparison of scalars and vectors. The existing manual solution is cumbersome, open to errors, slow, and cannot be inserted into an automated process. This invention is quick and easy to use, and can be inserted into an automated data-processing algorithm.

Applying the concept of quality of life to Israeli special education programs: a national curriculum for enhanced autonomy in students with special needs.

PubMed

Reiter, Shunit; Schalock, Robert L

2008-03-01

This study provides a description of the design and development of guidelines and programs for a national core curriculum for special education in Israel. Israel was exposed during the 1970s to the ideology of normalization. Later on, toward the end of the 1980s, the concept of quality of life was added. Several research studies were conducted, resulting in the following core ideas about education: a shift of emphasis from teaching independent-living skills to teaching autonomy, self-awareness, self-direction, and interdependence is required. On the basis of these ideas, a new model of instruction was devised and termed the 'cycle of internalized learning' (CIL). The CIL is based on a holistic orientation toward the student and builds on abilities rather than disabilities. The peer group is the basic unit of instruction. Attention is on processes and outcomes. The CIL involves several clearly defined teaching steps: (i) opening--the presentation of the subject matter; (ii) discussion--a conceptual analysis of the subject; (iii) open conversation--students discuss the issues they raised during the first session, express their personal life experiences while applying the new concepts they learned, and suggest possible solutions to problems; (iv) trying out the solutions suggested by students; and (v) repeated discussions, to arrive at personal and social conclusions. Currently there are three published units of the CIL: (i) Social Education, (ii) Career Education, and (iii) Towards Leaving Home for Independent Living in the Community. The fourth unit, on citizenship education through the use of computers, is in its final stages of preparation. The success of the implementation of the program is expressed both at the students' level--as an enhanced sense of self-worth and self-confidence, as well as enhanced academic achievements and social skills--and at the teachers' level--as a paradigm shift from a medical model of approach to students with disabilities to a social and humanistic one.

Biological Solar Energy Conversion and U.S. Energy Policy

ERIC Educational Resources Information Center

Pimentel, David; And Others

1978-01-01

Surveys energy consumption in the United States and explores the possibility of increasing the amount of energy obtained from biomass conversion (biologically produced energy). Economic and environmental concerns of biomass conversion processes are discussed. (CP)

Tables and conversions for microclimatology.

Treesearch

James M. Brown

1973-01-01

A series of tables, charts, and conversion factors have been prepared for use in microclimatic and ecological studies. Included are: the solution to various equations of radiant energy exchange; solar radiation diagrams; psychometric and precipitation data; and unit conversion factors.

Multifunctional switching unit for add/drop, wavelength conversion, format conversion, and WDM multicast based on bidirectional LCoS and SOA-loop architecture.

PubMed

Wang, Danshi; Zhang, Min; Qin, Jun; Lu, Guo-Wei; Wang, Hongxiang; Huang, Shanguo

2014-09-08

We propose a multifunctional optical switching unit based on the bidirectional liquid crystal on silicon (LCoS) and semiconductor optical amplifier (SOA) architecture. Add/drop, wavelength conversion, format conversion, and WDM multicast are experimentally demonstrated. Due to the bidirectional characteristic, the LCoS device cannot only multiplex the input signals, but also de-multiplex the converted signals. Dual-channel wavelength conversion and format conversion from 2 × 25Gbps differential quadrature phase-shift-keying (DQPSK) to 2 × 12.5Gbps differential phase-shift-keying (DPSK) based on four-wave mixing (FWM) in SOA is obtained with only one pump. One-to-six WDM multicast of 25Gbps DQPSK signals with two pumps is also achieved. All of the multicast channels are with a power penalty less than 1.1 dB at FEC threshold of 3.8 × 10⁻³.

Associations of Mother-Child Reminiscing about Negative Past Events, Coping, and Self-Concept in Early Childhood

ERIC Educational Resources Information Center

Goodvin, Rebecca; Romdall, Lisa

2013-01-01

Parent-child reminiscing conversations in early childhood have received theoretical attention as a forum for children's self-concept development, but this has been little addressed in empirical work. This study examines associations between emotion reminiscing and children's self-concepts and, building from the reminiscing and…

THE THEME-CONCEPT UNIT IN LITERATURE.

ERIC Educational Resources Information Center

HILLOCKS, GEORGE, JR.

A SUGGESTED UNIT FRAMEWORK WAS DEVELOPED AS A METHOD OF TEACHING SEVENTH-GRADE LITERATURE AT EUCLID CENTRAL JUNIOR HIGH SCHOOL IN EUCLID, OHIO. THE UNIT WAS DIVIDED INTO SIX MAJOR SECTIONS--(1) DEVELOPMENT OF THE CONCEPT, (2) APPLICATION OF THE CONCEPT UNDER THE GUIDANCE OF A TEACHER, (3) REVISION OF THE CONCEPT, (4) APPLICATION OF THE CONCEPT BY…

Megawatt Class Nuclear Space Power Systems (MCNSPS) conceptual design and evaluation report. Volume 4: Concepts selection, conceptual designs, recommendations

NASA Technical Reports Server (NTRS)

Wetch, J. R.

1988-01-01

A study was conducted by NASA Lewis Research Center for the Triagency SP-100 program office. The objective was to determine which reactor, conversion and radiator technologies would best fulfill future Megawatt Class Nuclear Space Power System Requirements. The requirement was 10 megawatts for 5 years of full power operation and 10 years system life on orbit. A variety of liquid metal and gas cooled reactors, static and dynamic conversion systems, and passive and dynamic radiators were considered. Four concepts were selected for more detailed study: (1) a gas cooled reactor with closed cycle Brayton turbine-alternator conversion with heatpipe and pumped tube fin rejection, (2) a Lithium cooled reactor with a free piston Stirling engine-linear alternator and a pumped tube-fin radiator,(3) a Lithium cooled reactor with a Potassium Rankine turbine-alternator and heat pipe radiator, and (4) a Lithium cooled incore thermionic static conversion reactor with a heat pipe radiator. The systems recommended for further development to meet a 10 megawatt long life requirement are the Lithium cooled reactor with the K-Rankine conversion and heat pipe radiator, and the Lithium cooled incore thermionic reactor with heat pipe radiator.

Down-conversion IM-DD RF photonic link utilizing MQW MZ modulator.

PubMed

Xu, Longtao; Jin, Shilei; Li, Yifei

2016-04-18

We present the first down-conversion intensity modulated-direct detection (IM-DD) RF photonic link that achieves frequency down-conversion using the nonlinear optical phase modulation inside a Mach-Zehnder (MZ) modulator. The nonlinear phase modulation is very sensitive and it can enable high RF-to-IF conversion efficiency. Furthermore, the link linearity is enhanced by canceling the nonlinear distortions from the nonlinear phase modulation and the MZ interferometer. Proof-of-concept measurement was performed. The down-conversion IM-DD link demonstrated 28dB improvement in distortion levels over that of a conventional IM-DD link using a LiNbO₃ MZ modulator.

Conversation, development, and gender: a study of changes in children's concepts of punishment.

PubMed

Leman, Patrick J; Björnberg, Marina

2010-01-01

One hundred thirty-three children, average age 9.58 years, were read vignettes describing a moral transgression and then discussed what would constitute a fair punishment. Children's gender influenced conversation dynamics (use of interruption and other simultaneous speech) but not conversation content (justifications for judgments). All children who engaged in conversation showed development in judgments after 8 weeks compared with a control (no interaction) group. However, there was no relation between conversation dynamics or content and development, or any effects of gender, on the developmental process. The benefits of peer collaboration were general rather than specific to the stimulus story.

77 FR 42653 - United States Navy Restricted Area, SUPSHIP Gulf Coast Detachment Mobile at AUSTAL, USA, Mobile...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-20

... restricted area established around the AUSTAL, USA shipbuilding facility located in Mobile, Alabama. The Supervisor of Shipbuilding, Conversion and Repair, United States Navy (USN), Gulf Coast (SUPSHIP Gulf Coast..., 2011, replacing the Supervisor of Shipbuilding, Conversion, and Repair, USN, Bath (SUPSHIP Bath). The...

A Novel Oscillating Rectenna for Wireless Microwave Power Transmission

NASA Technical Reports Server (NTRS)

McSpadden, J. O.; Dickinson, R. M.; Fan, L.; Chang, K.

1998-01-01

A new concept for solid state wireless microwave power transmission is presented. A 2.45 GHz rectenna element that was designed for over 85% RF to dc power conversion efficiency has been used to oscillate at 3.3 GHz with an approximate 1% dc to RF conversion efficiency.

Combinatorial enzyme technology: Conversion of pectin to oligo species and its effect on microbial growth

USDA-ARS?s Scientific Manuscript database

Plant cell wall polysaccharides, which consist of polymeric backbones with various types of substitution, were studied using the concept of combinatorial enzyme technology for conversion of agricultural fibers to functional products. Using citrus pectin as the starting substrate, an active oligo spe...

Teaching Race and Social Justice at a Predominantly White Institution

ERIC Educational Resources Information Center

Bauer, Kelly; Clancy, Kelly

2018-01-01

At our predominantly white university, students often shy away from controversial conversations. How can the classroom encourage students to value and engage in potentially explosive conversations? We develop a concept of "empathic scaffolding" to articulate an approach that integrates diversity and inclusion into the classroom. Empathic…

School District Financial Management and Banking.

ERIC Educational Resources Information Center

Dembowski, Frederick L.; Davey, Robert D.

This chapter of "Principles of School Business Management" introduces the concept of cash management, or the process of managing an institution's moneys to ensure maximum cash availability and maximum yield on investments. Four activities are involved: (1) conversion of accounts receivable to cash receipts; (2) conversion of accounts payable to…

A geothermal AMTEC system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schuller, M.J.; LeMire, R.A.; Horner-Richardson, K.

1995-12-31

The Phillips Laboratory Power and Thermal Management Division (PL/VTP), with the support of ORION International Technologies, is investigating new methods of advanced thermal to electric power conversion for space and terrestrial applications. The alkali metal thermal-to-electric converter (AMTEC), manufactured primarily by Advanced Modular Power Systems (AMPS) of Ann Arbor, MI, has reached a level of technological maturity which would allow its use in a constant, unattended thermal source, such as a geothermal field. Approximately 95,000 square miles in the western United States has hot dry rock with thermal gradients of 60 C/km and higher. Several places in the United Statesmore » and the world have thermal gradients of 500 C/km. Such heat sources represent an excellent thermal source for a system of modular power units using AMTEC devices to convert the heat to electricity. AMTEC cells using sodium as a working fluid require heat input at temperatures between 500 and 1,000 C to generate power. The present state of the art is capable of 15% efficiency with 800 C heat input and has demonstrated 18% efficiency for single cells. This paper discusses the basics of AMTEC operation, current drilling technology as a cost driver, design of modular AMTEC power units, heat rejection technologies, materials considerations, and estimates of power production from a geothermal AMTEC concept.« less

Learning science in small groups: The relationship of conversation to conceptual understanding

NASA Astrophysics Data System (ADS)

McDonald, James Tarleton

The purpose of this study was to investigate the relationship between conversation and conceptual understanding of erosion. The objective of this study was to investigate how fifth grade students' conceptions of erosion changed while they used stream tables and worked in groups of four within an inquiry-based curriculum. This study used symbolic interactionism and sociocognitive frameworks to interpret science learning in the elementary classroom. The research focused on the conceptual understanding of the focal group students, their use of classroom discourse to talk about their understandings of erosion, and the expertise that emerged while using stream tables. This study took place over a one-semester long study on erosion. Key informants were eight fifth graders. The data sources consisted of children's journals; transcripts of audiotaped interviews with the key informants before, during, and after the erosion unit; transcripts of videotapes of the students using the stream tables; and field notes recording children's discourse and activity. Individual and group cases were constructed during the study. The knowledge of the eight focal group children was placed on a hierarchy of conceptual understanding that contained 8 components of the erosion process. All four of the students whose ideas were examined in depth gained in their conceptual understanding of erosion. Students' individual expertise enhanced their own conceptual understanding. The contribution of classroom discourse and expertise to conceptual understanding differed between the two focal groups. Group 1 used essential expertise to sustain generative conversations, maximizing their learning opportunities. Students in Group 1 got along with one another, rotated assigned roles and jobs, and were able to start their own generative conversations. Members of Group 1 asked generative questions, connected stream table events to real life situations, and involved everyone in the group. Group 2 engaged in a predominance of procedural discourse and had fewer learning opportunities. Group 2 had two dominant personalities who developed a conflict over roles and jobs, keeping their peers out of the conversation. Students in Group 2 had generative conversations, but these were not sustained due to the lack of acknowledgment of peer expertise and the starting their own generative conversations.

Biological carbon dioxide utilisation in food waste anaerobic digesters.

PubMed

Fernández, Y Bajón; Green, K; Schuler, K; Soares, A; Vale, P; Alibardi, L; Cartmell, E

2015-12-15

Carbon dioxide (CO2) enrichment of anaerobic digesters (AD) was previously identified as a potential on-site carbon revalorisation strategy. This study addresses the lack of studies investigating this concept in up-scaled units and the need to understand the mechanisms of exogenous CO2 utilisation. Two pilot-scale ADs treating food waste were monitored for 225 days, with the test unit being periodically injected with CO2 using a bubble column. The test AD maintained a CH4 production rate of 0.56 ± 0.13 m(3) CH4·(kg VS(fed) d)(-1) and a CH4 concentration in biogas of 68% even when dissolved CO2 levels were increased by a 3 fold over the control unit. An additional uptake of 0.55 kg of exogenous CO2 was achieved in the test AD during the trial period. A 2.5 fold increase in hydrogen (H2) concentration was observed and attributed to CO2 dissolution and to an alteration of the acidogenesis and acetogenesis pathways. A hypothesis for conversion of exogenous CO2 has been proposed, which requires validation by microbial community analysis. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Alleviating Pressure on Water Resources: A new approach could be attempted

NASA Astrophysics Data System (ADS)

Sun, Shikun; Wang, Yubao; Wang, Feifei; Liu, Jing; Luan, Xiaobo; Li, Xiaolei; Zhou, Tianwa; Wu, Pute

2015-09-01

Water and food safety are two major challenges which the world faces today. Traditional water management focuses on the reduction of water use through improvements in water saving technologies. However, quantitative research is needed to evaluate the effects of changing food consumption patterns on water resources. Here we report the water saving effects of changing diet pattern of the major crops and animal products in mainland China. By using the concepts of water footprint (WF) per weight unit and per calorie unit, provided by 13 primary crop and animal products, the WFs of the 13 agricultural products in each province are compared, and their water/energy conversion efficiencies are analyzed. Then, impacts of different scenarios of changing diet pattern on water consumption were explored. Results show that there are obvious differences between the WF per weight and calorie unit provided by crop and animal products due to the nutritional properties of the agricultural products. Promoting water savings from the food consumption side could give a positive feedback on water consumption. Scenario analysis of adjustments to the diet pattern proves that it is potentially feasible to reach the objective of alleviating stress on water resources while guaranteeing nutritional value of the residents.

Alleviating Pressure on Water Resources: A new approach could be attempted.

PubMed

Sun, Shikun; Wang, Yubao; Wang, Feifei; Liu, Jing; Luan, Xiaobo; Li, Xiaolei; Zhou, Tianwa; Wu, Pute

2015-09-14

Water and food safety are two major challenges which the world faces today. Traditional water management focuses on the reduction of water use through improvements in water saving technologies. However, quantitative research is needed to evaluate the effects of changing food consumption patterns on water resources. Here we report the water saving effects of changing diet pattern of the major crops and animal products in mainland China. By using the concepts of water footprint (WF) per weight unit and per calorie unit, provided by 13 primary crop and animal products, the WFs of the 13 agricultural products in each province are compared, and their water/energy conversion efficiencies are analyzed. Then, impacts of different scenarios of changing diet pattern on water consumption were explored. Results show that there are obvious differences between the WF per weight and calorie unit provided by crop and animal products due to the nutritional properties of the agricultural products. Promoting water savings from the food consumption side could give a positive feedback on water consumption. Scenario analysis of adjustments to the diet pattern proves that it is potentially feasible to reach the objective of alleviating stress on water resources while guaranteeing nutritional value of the residents.

Alleviating Pressure on Water Resources: A new approach could be attempted

PubMed Central

Sun, Shikun; Wang, Yubao; Wang, Feifei; Liu, Jing; Luan, Xiaobo; Li, Xiaolei; Zhou, Tianwa; Wu, Pute

2015-01-01

Water and food safety are two major challenges which the world faces today. Traditional water management focuses on the reduction of water use through improvements in water saving technologies. However, quantitative research is needed to evaluate the effects of changing food consumption patterns on water resources. Here we report the water saving effects of changing diet pattern of the major crops and animal products in mainland China. By using the concepts of water footprint (WF) per weight unit and per calorie unit, provided by 13 primary crop and animal products, the WFs of the 13 agricultural products in each province are compared, and their water/energy conversion efficiencies are analyzed. Then, impacts of different scenarios of changing diet pattern on water consumption were explored. Results show that there are obvious differences between the WF per weight and calorie unit provided by crop and animal products due to the nutritional properties of the agricultural products. Promoting water savings from the food consumption side could give a positive feedback on water consumption. Scenario analysis of adjustments to the diet pattern proves that it is potentially feasible to reach the objective of alleviating stress on water resources while guaranteeing nutritional value of the residents. PMID:26364756

Advanced direct coal liquefaction concepts. Quarterly report, January 1, 1994--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

A detailed evaluation of the bench unit data on Black Thunder feedstocks was completed. The results show that in a once-through operation using counterflow, reactor technology coal conversions in excess of 90% could be obtained, giving distillable oil yields in the range 60--65 wt % on MAF coal. The remaining non-distillable oil fraction which represents 20--25 wt % on MAF coal is a source of additional distillable oil in further processing, for example, bottoms recycle operation. C{sub 1}-C{sub 3} gas yields were generally in the order of 6--8 wt %. In autoclave studies, Illinois No. 6 coal was found tomore » be much less reactive than Black Thunder coal, and did not respond well to solubilization with carbon monoxide/steam. Process severity was, therefore, increased for bench unit operations on Illinois No. 6 coal, and work has concentrated on the use of hydrogen rather than carbon monoxide for solubilization. Preliminary coking studies on the resid from bench unit runs on Black Thunder coal were also carried out. Distillable liquid yields of 55--60 wt % were obtained. The technical and economic study to be carried out by Kilborn Engineering Company has been initiated.« less

Conversion of the TRACON operations concepts database into a formal sentence outline job task taxonomy.

DOT National Transportation Integrated Search

1995-05-01

FAA Air Traffic Control Operations Concepts Volume VII.- TRACON Controllers (1989) developed by CTA, Inc., a technical description of the duties of a TRACON air traffic control specialist (ATCS), formatted in User Interface Language, was restructured...

What Is Classroom Discussion? A Look at Teachers' Conceptions.

ERIC Educational Resources Information Center

Larson, Bruce E.; Parker, Walter C.

1996-01-01

Explores three social-studies teachers' conceptions of classroom discussion, focusing on discussion's defining characteristics and purpose and influences on usage. Data included interview and think-aloud responses and classroom observations. Teachers view discussion as recitation, teacher-directed conversation, open-ended exploration, a…

Development and Deployment Assessment of a Melt-Down Proof Modular Micro Reactor (MDP-MMR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hawari, Ayman I.; Venneri, Francesco

The objective of this project is to perform feasibility assessment and technology gap analysis and establish a development roadmap for an innovative and highly compact Micro Modular Reactor (MMR) concept that integrates power production, power conversion and electricity generation in a single unit. The MMR is envisioned to use fully ceramic micro-encapsulated (FCM) fuel, a particularly robust form of TRISO fuel, and to be gas-cooled (e.g., He or CO 2) and capable of generating power in the range of 10 to 40 MW-thermal. It is designed to be absolutely melt-down proof (MDP) under all circumstances including complete loss of coolantmore » scenarios with no possible release of radioactive material, to be factory produced, to have a cycle length of greater than 20 years, and to be highly proliferation resistant. In addition, it will be transportable, retrievable and suitable for use in remote areas. As such, the MDP-MMR will represent a versatile reactor concept that is suitable for use in various applications including electricity generation, process heat utilization and propulsion.« less

Evaluation of a value prior to pulping-thermomechanical pulp business concept. Part 2.

Treesearch

Ted Bilek; Carl Houtman; Peter Ince

2011-01-01

Value Prior to Pulping (VPP) is a novel biorefining concept for pulp mills that includes hydrolysis extraction of hemicellulose wood sugars and acetic acid from pulpwood prior to pulping. The concept involves conversion of wood sugars via fermentation to fuel ethanol or other chemicals and the use of remaining solid wood material in the pulping process. This paper...

Reflexions sur les marqueurs de structuration de la conversation (Considerations on the Structural Markers of Conversation).

ERIC Educational Resources Information Center

Auchlin, Antoine

1981-01-01

Examines morphemic markers that signal the opening and closing of discourse units, emphasizing their complexity and their central role for a descriptive model of conversation. Then proceeds to analyze their functions within the overall structure of conversation, classifying them according to their properties and uses. Societe Nouvelle Didier…

Interactivite, relations entre interlocuteurs et constitution d'unites conversationnelles (Interaction Processes, Participants' Relationships and Definition of Conversation Units).

ERIC Educational Resources Information Center

Zenone, Anna

1981-01-01

Analyzes a type of conversational exchange where the participants focus on a given subject or theme contributing personal views to the discussion. Characterizes the relationship among the participants as a "cooperative conflict," examining the internal structure of speech acts and their illocutory functions, particularly the initiatory…

75 FR 8391 - Assisted Living Conversion Program (ALCP) and Emergency Capital Repair Program (ECRP)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

... submitted to the Office of Management and Budget (OMB) for review, as required by the Paperwork Reduction... Conversion Program (ALCP) provides funding for the physical costs of converting some or all the units of an...) provides funding for the physical costs of converting some or all the units of an eligible multifamily...

Conversion of grazed pastures to energy cane as a biofuel feedstock alters the emission of GHGs from soils in Southeastern United States

USDA-ARS?s Scientific Manuscript database

The cultivation of energy cane throughout the Southeastern United States may displace grazed pastures on organic soil (Histosols) to meet growing demands for biofuels. We combined results from a field experiment with a biogeochemical model to improve our understanding of how the conversion of pastur...

Bilingual Education in the United States, the Pacific and Southeast Asia.

ERIC Educational Resources Information Center

Lester, Mark

1974-01-01

In classifying bilingual education following William F. Mackey's typology, single or dual media or instruction may be used for gradual or abrupt conversion to a wider or narrower culture. Bilingual education in the United States is usually dual medium, either for maintenance or conversion to a wider culture, aiming to produce a bilingual…

Evolution of systems concepts for a 100 kWe class Space Nuclear Power System

NASA Technical Reports Server (NTRS)

Katucki, R.; Josloff, A.; Kirpich, A.; Florio, F.

1985-01-01

Conceptual designs for the SP-100 Space Nuclear Power System have been prepared that meet baseline, backup and growth program scenarios. Near-term advancement in technology was considered in the design of the Baseline Concept. An improved silicon-germanium thermoelectric technique is used to convert the heat from a fast-spectrum, liquid lithium cooled reactor. This system produces a net power of 100 kWe with a 10-year end of life, under the specific constraints of area and volume. Output of the Backup Concept is estimated to be 60 kWe for a 10-year end of life. This system differs from the Baseline Concept because currently available thermoelectric conversion is used from energy supplied by a liquid sodium cooled reactor. The Growth Concept uses Stirling engine conversion to produce 100 kWe within the constraints of mass and volume. The Growth Concept can be scaled up to produce a 1 MWe output that uses the same type reactor developed for the Baseline Concept. Assessments made for each of the program scenarios indicate the key development efforts needed to initiate detailed design and hardware program phases. Development plans were prepared for each scenario that detail the work elements and show the program activities leading to a state of flight readiness.

40 CFR 60.73 - Emission monitoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operator shall establish a conversion factor for the purpose of converting monitoring data into units of the applicable standard (kg/metric ton, lb/ton). The conversion factor shall be established by... represents emission measurements concurrent with the reference method test periods, the conversion factor...

Solar Pilot Plant, Phase I. Preliminary design report. Volume II, Book 2. Central receiver optical model users manual. CDRL item 2. [HELIAKI code

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1977-05-01

HELIAKI is a FORTRAN computer program which simulates the optical/thermal performance of a central receiver solar thermal power plant for the dynamic conversion of solar-generated heat to electricity. The solar power plant which this program simulates consists of a field of individual sun tracking mirror units, or heliostats, redirecting sunlight into a cavity, called the receiver, mounted atop a tower. The program calculates the power retained by that cavity receiver at any point in time or the energy into the receiver over a year's time using a Monte Carlo ray trace technique to solve the multiple integral equations. An artist'smore » concept of this plant is shown.« less

The Base Engine for Solar Stirling Power

NASA Technical Reports Server (NTRS)

Meijer, R. J.; Godett, T. M.

1984-01-01

A new concept in Stirling engine technology is embodied in the base engine now being developed at Stirling Thermal Motors, Inc. This is a versatile energy conversion unit suitable for many different applications and heat sources. The base engine, rated 40 kW at 2800 RPM, is a four-cylinder, double-acting variable displacement Stirling engine with pressurized crankcase and rotating shaft seal. Remote-heating technology is incorporated with a stacked-heat-exchanger configuration and a liquid metal heat pipe connected to a distinctly separate combustor or other heat source. High efficiency over a wide range of operating conditions, long life, low manufacturing cost and low material cost are specifically emphasized. The base engine, its design philosophy and approach, its projected performance, and some of its more attractive applications are described.

Bioengineering and Cybernetics: A Modern Caduceus.

PubMed

Magin, Richard L

2017-01-01

Like the caduceus, a medical symbol of entwined serpents, bioengineering and cybernetics have interwoven together ideas and concepts for over 50 years. Half a century is a long time, and whether we are talking about an academic discipline, our lives, or an old car, achieving 50 is a number that brings pause to the conversation. In books, wine, or collectibles, 50 years is termed vintage, which carries the connotation of depth and maturity. Certainly, in the case of the discipline of bioengineering, 50 years is a milestone of growth and development. By all academic measures (number of departments, current enrollment and graduates, size of faculty, and impact factor for its publications), bioengineering is a mature discipline. Presently, there are almost 100 ABET-certified bioengineering degree programs in the United States alone.

Geometric and Algebraic Approaches in the Concept of Complex Numbers

ERIC Educational Resources Information Center

Panaoura, A.; Elia, I.; Gagatsis, A.; Giatilis, G.-P.

2006-01-01

This study explores pupils' performance and processes in tasks involving equations and inequalities of complex numbers requiring conversions from a geometric representation to an algebraic representation and conversions in the reverse direction, and also in complex numbers problem solving. Data were collected from 95 pupils of the final grade from…

Solar Program Assessment: Environmental Factors - Ocean Thermal Energy Conversion.

ERIC Educational Resources Information Center

Energy Research and Development Administration, Washington, DC. Div. of Solar Energy.

This report presents the environmental problems which may arise with the further development of Ocean Thermal Energy Conversion, one of the eight Federally-funded solar technologies. To provide a background for this environmental analysis, the history and basic concepts of the technology are reviewed, as are its economic and resource requirements.…

Designing for Learning Conversations: How Parents Support Children's Science Learning within an Immersive Simulation

ERIC Educational Resources Information Center

Tscholl, Michael; Lindgren, Robb

2016-01-01

This research investigates the social learning affordances of a room-sized, immersive, and interactive augmented reality simulation environment designed to support children's understanding of basic physics concepts in a science center. Conversations between 97 parent-child pairs were analyzed in relation to categories of talk through which…

Advising Older Homeowners on Home Equity Conversion: A Guide for Attorneys.

ERIC Educational Resources Information Center

Schimeall, Kent M.; Ernst, Trudy A.

This manual is intended to introduce attorneys to the concept of home equity conversion (HEC) so that they can knowledgeably advise elderly homeowners who may be considering this type of transaction. It is directed to attorneys representing the elderly rather than to attorneys representing lenders or investors in home equity conversion…

Alternative Architecture for Commercial Space Solar Power

NASA Technical Reports Server (NTRS)

Potter, Seth

2000-01-01

This presentation discuss the space solar power (SSP) concept. It takes us step by step through the process: the use of sunlight and solar cells to create power, the conversion of the sunlight into electricity, the conversion of electricity to microwaves, and finally the from microwaves back to electricity by the Rectennas on Earth.

The Journey of Organizational Unlearning: A Conversation with William H. Starbuck

ERIC Educational Resources Information Center

Nguyen, Nhien

2017-01-01

Purpose: This paper aims to provide an overview of the concept "organizational unlearning" and its development since it was first introduced to the management literature and presents a useful perspective that can help to advance the conceptual development of this topic. Design/methodology/approach: Through a conversation with celebrated…

Photovoltaic conversion of laser energy

NASA Technical Reports Server (NTRS)

Stirn, R. J.

1976-01-01

The Schottky barrier photovoltaic converter is suggested as an alternative to the p/n junction photovoltaic devices for the conversion of laser energy to electrical energy. The structure, current, output, and voltage output of the Schottky device are summarized. The more advanced concepts of the multilayer Schottky barrier cell and the AMOS solar cell are briefly considered.

Dialogue on Modernity and Modern Education in Dispute

ERIC Educational Resources Information Center

Baker, Michael; Peters, Michael A.

2012-01-01

This is a dialogue or conversation between Michael Baker (MB) and Michael A. Peters (MP) on the concept of modernity and its significance for educational theory. The dialogue took place originally as a conversation about a symposium on modernity held at the American Educational Studies Association meeting 2010. It was later developed for…

"Your Job Is to Take Care of Us": Teaching Our Way through the Boston Marathon Bombings

ERIC Educational Resources Information Center

Bentley, Dana Frantz

2015-01-01

The concept of social justice and critical thinking are prevalent topics in conversations about early childhood education. Usually, critical conversations around these practices tend to involve academics in discussion rather than include practitioners. In today's world, young children are frequently confronted with the realities of violence and…

Spiritual Conversation as Religiously Educative

ERIC Educational Resources Information Center

Díaz, Luz Marina

2017-01-01

This article proposes spiritual conversation as a religiously educative activity. Revelation as the relational activity of speaking-listening between the human and the divine in daily life, and education as an activity to show someone how to live and die, are key concepts for this study. This work includes a study of narrative at the heart of…

Low-speed wind tunnel test results of the Canard Rotor/Wing concept

NASA Technical Reports Server (NTRS)

Bass, Steven M.; Thompson, Thomas L.; Rutherford, John W.; Swanson, Stephen

1993-01-01

The Canard Rotor/Wing (CRW), a high-speed rotorcraft concept, was tested at the National Aeronautics and Space Administration (NASA) Ames Research Center's 40- by 80-Foot Wind Tunnel in Mountain View, California. The 1/5-scale model was tested to identify certain low-speed, fixed-wing, aerodynamic characteristics of the configuration and investigate the effectiveness of two empennages, an H-Tail and a T-Tail. The paper addresses the principal test objectives and the results achieved in the wind tunnel test. These are summarized as: i) drag build-up and differences between the H-Tail and T-Tail configuration, ii) longitudinal stability of the H-Tail and T-Tail configurations in the conversion and cruise modes, iii) control derivatives for the canard and elevator in the conversion and cruise modes, iv) aerodynamic characteristics of varying the rotor/wing azimuth position, and v) canard and tail lift/trim capability for conversion conditions.

The total flow concept for geothermal energy conversion

NASA Technical Reports Server (NTRS)

Austin, A. L.

1974-01-01

A geothermal development project has been initiated at the Lawrence Livermore Laboratory (LLL) to emphasize development of methods for recovery and conversion of the energy in geothermal deposits of hot brines. Temperatures of these waters vary from 150 C to more than 300 C with dissolved solids content ranging from less than 0.1% to over 25% by weight. Of particular interest are the deposits of high-temperature/high-salinity brines, as well as less saline brines, known to occur in the Salton Trough of California. Development of this resource will depend on resolution of the technical problems of brine handling, scale and precipitation control, and corrosion/erosion resistant systems for efficient conversion of thermal to electrical energy. Research experience to date has shown these problems to be severe. Hence, the LLL program emphasizes development of an entirely different approach called the Total Flow concept.

All-optical analog comparator.

PubMed

Li, Pu; Yi, Xiaogang; Liu, Xianglian; Zhao, Dongliang; Zhao, Yongpeng; Wang, Yuncai

2016-08-23

An analog comparator is one of the core units in all-optical analog-to-digital conversion (AO-ADC) systems, which digitizes different amplitude levels into two levels of logical '1' or '0' by comparing with a defined decision threshold. Although various outstanding photonic ADC approaches have been reported, almost all of them necessitate an electrical comparator to carry out this binarization. The use of an electrical comparator is in contradiction to the aim of developing all-optical devices. In this work, we propose a new concept of an all-optical analog comparator and numerically demonstrate an implementation based on a quarter-wavelength-shifted distributed feedback laser diode (QWS DFB-LD) with multiple quantum well (MQW) structures. Our results show that the all-optical comparator is very well suited for true AO-ADCs, enabling the whole digital conversion from an analog optical signal (continuous-time signal or discrete pulse signal) to a binary representation totally in the optical domain. In particular, this all-optical analog comparator possesses a low threshold power (several mW), high extinction ratio (up to 40 dB), fast operation rate (of the order of tens of Gb/s) and a step-like transfer function.

All-optical analog comparator

PubMed Central

Li, Pu; Yi, Xiaogang; Liu, Xianglian; Zhao, Dongliang; Zhao, Yongpeng; Wang, Yuncai

2016-01-01

An analog comparator is one of the core units in all-optical analog-to-digital conversion (AO-ADC) systems, which digitizes different amplitude levels into two levels of logical ‘1’ or ‘0’ by comparing with a defined decision threshold. Although various outstanding photonic ADC approaches have been reported, almost all of them necessitate an electrical comparator to carry out this binarization. The use of an electrical comparator is in contradiction to the aim of developing all-optical devices. In this work, we propose a new concept of an all-optical analog comparator and numerically demonstrate an implementation based on a quarter-wavelength-shifted distributed feedback laser diode (QWS DFB-LD) with multiple quantum well (MQW) structures. Our results show that the all-optical comparator is very well suited for true AO-ADCs, enabling the whole digital conversion from an analog optical signal (continuous-time signal or discrete pulse signal) to a binary representation totally in the optical domain. In particular, this all-optical analog comparator possesses a low threshold power (several mW), high extinction ratio (up to 40 dB), fast operation rate (of the order of tens of Gb/s) and a step-like transfer function. PMID:27550874

All-optical analog comparator

NASA Astrophysics Data System (ADS)

Li, Pu; Yi, Xiaogang; Liu, Xianglian; Zhao, Dongliang; Zhao, Yongpeng; Wang, Yuncai

2016-08-01

An analog comparator is one of the core units in all-optical analog-to-digital conversion (AO-ADC) systems, which digitizes different amplitude levels into two levels of logical ‘1’ or ‘0’ by comparing with a defined decision threshold. Although various outstanding photonic ADC approaches have been reported, almost all of them necessitate an electrical comparator to carry out this binarization. The use of an electrical comparator is in contradiction to the aim of developing all-optical devices. In this work, we propose a new concept of an all-optical analog comparator and numerically demonstrate an implementation based on a quarter-wavelength-shifted distributed feedback laser diode (QWS DFB-LD) with multiple quantum well (MQW) structures. Our results show that the all-optical comparator is very well suited for true AO-ADCs, enabling the whole digital conversion from an analog optical signal (continuous-time signal or discrete pulse signal) to a binary representation totally in the optical domain. In particular, this all-optical analog comparator possesses a low threshold power (several mW), high extinction ratio (up to 40 dB), fast operation rate (of the order of tens of Gb/s) and a step-like transfer function.

Agricultural Land Conversion: Background and Issues.

ERIC Educational Resources Information Center

Furuseth, Owen J.

1982-01-01

Analyzes forces contributing to the conversion of agricultural land for other uses, causes for the depletion of the land, major issues surrounding the loss of farmland, and current policies designed to control haphazard land conversion. Concludes that the United States lacks a national farmland protection policy. (KC)

U.S. metric board 1979 survey of selected large U.S. firms and industries

NASA Astrophysics Data System (ADS)

King, L. L.

1980-05-01

A mail survey of randomly chosen 202 of the 1000 largest manufacturing and mining firms, as listed by Fortune magazine, was conducted in late 1979 and early 1980. About 64 percent (112 firms) responded with useful data. Among the findings are: about 63 percent of the largest firms produce at least one metric product; about 48 percent of exported sales are of metric products; about three quarters of the firms selling metric products sell products labelled in customary and metric units (soft conversion); about half the firms selling metric products sell hard converted products (products manufactured in metric units); little corporate coordination and planning seems to accompany conversion to the metric system; about one-third of the firms see laws and reputation impeding conversion; over 50 percent see lack of customer demand as inhibiting conversion; and the most realistic time period for conversion is 10 years, the minimum time for conversion (under pressure) is three years, and the perferred time (at the firm's own pace) is eight years.

Overview study of Space Power Technologies for the advanced energetics program. [spacecraft

NASA Technical Reports Server (NTRS)

Taussig, R.; Gross, S.; Millner, A.; Neugebauer, M.; Phillips, W.; Powell, J.; Schmidt, E.; Wolf, M.; Woodcock, G.

1981-01-01

Space power technologies are reviewed to determine the state-of-the-art and to identify advanced or novel concepts which promise large increases in performance. The potential for incresed performance is judged relative to benchmarks based on technologies which have been flight tested. Space power technology concepts selected for their potentially high performance are prioritized in a list of R & D topical recommendations for the NASA program on Advanced Energetics. The technology categories studied are solar collection, nuclear power sources, energy conversion, energy storage, power transmission, and power processing. The emphasis is on electric power generation in space for satellite on board electric power, for electric propulsion, or for beamed power to spacecraft. Generic mission categories such as low Earth orbit missions and geosynchronous orbit missions are used to distinguish general requirements placed on the performance of power conversion technology. Each space power technology is judged on its own merits without reference to specific missions or power systems. Recommendations include 31 space power concepts which span the entire collection of technology categories studied and represent the critical technologies needed for higher power, lighter weight, more efficient power conversion in space.

Analysis of the reflective multibandgap solar cell concept

NASA Technical Reports Server (NTRS)

Stern, T. G.

1983-01-01

A new and unique approach to improving photovoltaic conversion efficiency, the reflective multiband gap solar cell concept, was examined. This concept uses back surface reflectors and light trapping with several physically separated cells of different bandgaps to make more effective use of energy from different portions of the solar spectrum. Preliminary tests performed under General Dynamics Independent Research and Development (IRAD) funding have demonstrated the capability for achieving in excess of 20% conversion efficiency with aluminum gallium arsenide and silicon. This study analyzed the ultimate potential for high conversion efficiency with 2, 3, 4, and 5 different bandgap materials, determined the appropriate bandgaps needed to achieve this optimized efficiency, and identified potential problems or constraints. The analysis indicated that an improvement in efficiency of better than 40% could be attained in this multibandgap approach, compared to a single bandgap converter under the same assumptions. Increased absorption loss on the back surface reflector was found to incur a minimal penalty on efficiency for two and three bandgap systems. Current models for bulk absorption losses in 3-5 materials were found to be inadequate for explaining laboratory observed transmission losses. Recommendations included the continued development of high bandgap back surface reflector cells and basic research on semiconductor absorption mechanisms.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The original concept envisioned for the use of Fischer-Tropsch processing (FTP) of United States associated natural gas in this study was to provide a way of utilizing gas which could not be brought to market because a pipeline was not available or for which there was no local use. Conversion of gas by FTP could provide a means of utilizing offshore associated gas which would not require installation of a pipeline or re-injection. The premium quality F-T hydrocarbons produced by conversion of the gas can be transported in the same way as the crude oil or in combination (blended) withmore » it, eliminating the need for a separate gas transport system. FTP will produce a synthetic crude oil, thus increasing the effective size of the resource. The two conventional approaches currently used in US territory for handling of natural gas associated with crude petroleum production are re-injection and pipelining. Conversion of natural gas to a liquid product which can be transported to shore by tanker can be accomplished by FTP to produce hydrocarbons, or by conversion to chemical products such as methanol or ammonia, or by cryogenic liquefaction (LNG). This study considers FTP and briefly compares it to methanol and LNG. The Energy International Corporation cobalt catalyst, ratio adjusted, slurry bubble column F-T process was used as the basis for the study and the comparisons. An offshore F-T plant can best be accommodated by an FPSO (Floating Production, Storage, Offloading vessel) based on a converted surplus tanker, such as have been frequently used around the world recently. Other structure types used in deep water (platforms) are more expensive and cannot handle the required load.« less

Topics in Semantic Representation

ERIC Educational Resources Information Center

Griffiths, Thomas L.; Steyvers, Mark; Tenenbaum, Joshua B.

2007-01-01

Processing language requires the retrieval of concepts from memory in response to an ongoing stream of information. This retrieval is facilitated if one can infer the gist of a sentence, conversation, or document and use that gist to predict related concepts and disambiguate words. This article analyzes the abstract computational problem…

Satellite Power Systems (SPS) Concept Definition Study. Volume 3: SPS Concept Evolution

NASA Technical Reports Server (NTRS)

Hanley, G.

1978-01-01

A solar photovoltaic satellite based upon the utilization of a GaAlAs solar cell is defined. Topics covered include silicon-based photovoltaics, solar thermal power conversion, microwave energy transmission, power distribution, structures, attitude control and stationkeeping, thermal, and information management and control.

Going Metric: An Analysis of Experiences in Five Nations and Their Implications for U.S. Educational Planning. Final Report.

ERIC Educational Resources Information Center

Chalupsky, Albert B.; And Others

This study was undertaken in order to gather information concerning conversion to the metric system by other countries which might be useful in planning for conversion by the United States. Representatives of organizations in five countries (United Kingdom, Australia, South Africa, New Zealand, and Canada) which had recently converted to the…

Investigation of current university research concerning energy conversion and conservation in small single-family dwellings

NASA Technical Reports Server (NTRS)

Grossman, G. R.; Roberts, A. S., Jr.

1975-01-01

An investigation was made of university research concerning energy conversion and conservation techniques which may be applied in small single-family residences. Information was accumulated through published papers, progress reports, telephone conversations, and personal interviews. A synopsis of each pertinent investigation is given. Finally, a discussion of the synopses is presented and recommendations are made concerning the applicability of concepts for the design and construction of NASA-Langley Research Center's proposed Technology Utilization House in Hampton, Virginia.

Conversion factors: SI metric and U.S. customary units

USGS Publications Warehouse

,

1977-01-01

The policy of the U.S. Geological Survey is to foster use of the International System of Units (SI) which was defined by the 11th General Conference of Weights and Measures in 1960. This modernized metric system constitutes an international "language" by means of which communications throughout the world's scientific and economic communities may be improved. This publication is designed to familiarize the reader with the SI units of measurement that correspond to the common units frequently used in programs of the Geological Survey. In the near future, SI units will be used exclusively in most publications of the Survey; the conversion factors provided herein will help readers to obtain a "feel" for each unit and to "think metric."

Roadmap on optical energy conversion

DOE PAGES

Boriskina, Svetlana V.; Green, Martin A.; Catchpole, Kylie; ...

2016-06-24

For decades, progress in the field of optical (including solar) energy conversion was dominated by advances in the conventional concentrating optics and materials design. In recent years, however, conceptual and technological breakthroughs in the fields of nanophotonics and plasmonics combined with a better understanding of the thermodynamics of the photon energy-conversion processes reshaped the landscape of energy-conversion schemes and devices. Nanostructured devices and materials that make use of size quantization effects to manipulate photon density of states offer a way to overcome the conventional light absorption limits. Novel optical spectrum splitting and photon-recycling schemes reduce the entropy production in themore » optical energy-conversion platforms and boost their efficiencies. Optical design concepts are rapidly expanding into the infrared energy band, offering new approaches to harvest waste heat, to reduce the thermal emission losses, and to achieve noncontact radiative cooling of solar cells as well as of optical and electronic circuitries. Light-matter interaction enabled by nanophotonics and plasmonics underlie the performance of the third- and fourth-generation energy-conversion devices, including up- and down-conversion of photon energy, near-field radiative energy transfer, and hot electron generation and harvesting. Finally, the increased market penetration of alternative solar energy-conversion technologies amplifies the role of cost-driven and environmental considerations. This roadmap on optical energy conversion provides a snapshot of the state of the art in optical energy conversion, remaining challenges, and most promising approaches to address these challenges. Leading experts authored 19 focused short sections of the roadmap where they share their vision on a specific aspect of this burgeoning research field. The roadmap opens up with a tutorial section, which introduces major concepts and terminology. As a result, it is our hope that the roadmap will serve as an important resource for the scientific community, new generations of researchers, funding agencies, industry experts, and investors.« less

Acceleration of Rural Industrialization Using Renewable Energy Technolgoy

NASA Astrophysics Data System (ADS)

Abdullah, Kamaruddin

2007-10-01

Solar, wind, biomass and micro-hydro can be found in abundant in almost all rural area throughout the world. Despite of the fact that there are already so many research results showing the potential application of these renewable resources to substitute fossil fuel and to increase added value of local products, however, up to now very view if any result that has been realized in significant way. A concept of Small Provessing Unit using renewable energy sources have been introduced in Indonesia since 1999, in which domestically developed conversion technology, such as the greenhouse effect (GHE) solar drying system has been applied to process agricultural products such as coffee, cocoa, soices, various types of fishes and sea weeds. In addition, hybrid nocturnal cooling method has also beeing developed and used to help the farmer in extending shelf life of tropical fruits and vegetables and therefore, contributed in reducing post harvest losses. The Small Processing Unit concept as well as the developed renewable energy technology are now gradually being appreciated by both the central and local authorities, the private sectors including the NGO. The demand of such system is also gradually increasing each year and the area of applications have been extended not only within the heavtily inhavited Java Island but also to the other island of Indonesia. Our experiences in dealing with the system have also been transferred to fellow ASEAN engineers as well as those coming from the African continent through training and workshops activities. The future direction of the development will be to enhace the role of the Small Processing Unit (SPU) by providing more value added facilities driven by renewable energy technology.

Linking FRRF Derived Photophysiology with Carbon-based Primary Productivity: Insights from Concepts of Cellular Energy Allocation

NASA Astrophysics Data System (ADS)

Schuback, N.; Schallenberg, C.; Duckham, C.; Flecken, M.; Maldonado, M. T.; Tortell, P. D.

2016-02-01

Active chlorophyll a fluorescence approaches, including fast repetition rate fluorometry (FRRF), have the potential to provide estimates of phytoplankton primary productivity at unprecedented spatial and temporal resolution. FRRF-derived productivity rates are based on estimates of charge separation in photosystem II (ETRRCII), which must be converted into ecologically relevant units of carbon fixation. Understanding sources of variability in the coupling of ETRRCII and carbon fixation provides important physiological insight into phytoplankton photosynthesis, and is critical for the application of FRRF as a primary productivity measurement tool. We present data from a series of experiments during which we simultaneously measured phytoplankton carbon fixation and ETRRCII in the iron-limited NE subarctic Pacific. Our results show significant variability of the derived conversion factor (Ve:C/nPSII), with highest values observed under conditions of excess excitation pressure at the level of photosystem II, caused by high light and/or low iron. Our results will be discussed in the context of metabolic plasticity, which evolved in phytoplankton to simultaneously maximize growth and provide photoprotection under fluctuating light and limiting nutrient availabilities. Because the derived conversion factor is associated with conditions of excess light, it correlates with the expression of non-photochemical quenching (NPQ) in the pigment antenna, also derived from FRRF measurements. Our results demonstrate a significant correlation between NPQ and the conversion factor Ve:C/nPSII, and the potential of this relationship to improve FRRF-based estimates of phytoplankton carbon fixation rates is discussed.

Units and symbols in solar energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beckman, W.A.; Bugler, J.W.; Cooper, P.L.

1978-01-01

The application of S.I. units to some common solar energy quantities is discussed and some conversions to S.I. units are given. Then, a list of preferred names, symbols and units is recommended. (SPH)

[Automatic tracing of conversion scales from conventional units to the SI system of units].

PubMed

Besozzi, M; Bianchi, P; Agrifoglio, L

1988-01-01

American medical journals, as the Journal of the American Medical Association (JAMA), and the American Journal of Clinical Pathology (AJCP), the Journal of the American Society of Clinical Pathologists (ASCP), are shifting to selected SI (Système International d'Unités) units for reporting measurements. Further discussion by the AMA, the ASCP and other organizations is required before consensus in the US medical community can be reached as to the extent of and time frame for conversion to SI for reporting clinical laboratory measurements: however this decision will certainly greatly speed up the process of conversion in European countries too. Transition to SI units will require the use of different reference ranges, and there will be a potential for serious misinterpretation of laboratory data unless well-planned educational programs are instituted before the change. A simple program written in Microsoft Basic for automatically tracing on one's personal computer (PC) monitor a dual scale, in the conventional and in the SI system of units, is presented here. The program may be easily implemented and run on every PC operating under MS-DOS, equipped with a CGA or an AT&T6300 graphic card: through the operating system the scales may also be printed on a dot-matrix graphic printer. We believe that this, and other tools of this kind, will be useful in the thorough educational process of those reading the reports, and will be an important factor in the success of conversion to SI reporting.

Reconceptualising "Identity Slippage": Additional Language Learning and (L2) Identity Development

ERIC Educational Resources Information Center

Armour, William

2009-01-01

This paper reconsiders the theoretical concept of "identity slippage" by considering a detailed exegesis of three model conversations taught to learners of Japanese as an additional language. To inform my analysis of these conversations and how they contribute to identity slippage, I have used the work of the systemic-functional linguist Jay Lemke…

Gallium arsenide (GaAs) power conversion concept

NASA Technical Reports Server (NTRS)

Nussberger, A. A.

1980-01-01

A summary design analysis of a GaAs power conversion system for the solar power satellite (SPS) is presented. Eight different satellite configuration options for the solar arrays are compared. Solar cell annealing effects after proton irradiation are considered. Mass estimates for the SPS and the effect of solar cell parameters on SPS array design are discussed.

Sorting Students into Learning

ERIC Educational Resources Information Center

Dunleavy, Jodene; Milton, Penny

2010-01-01

The qualities and outcomes advanced as the hallmarks of 21st century learning have been part of the conversation about public education for decades. Since 2007, What did you do in school today? has been building on the established concepts of social and academic (or institutional) engagement and advancing the newer concept of intellectual…

Multiple Solutions Approach (MSA): Conceptions and Practices of Primary School Teachers in Ghana

ERIC Educational Resources Information Center

Nabie, Michael Johnson; Raheem, Kolawole; Agbemaka, John Bijou; Sabtiwu, Rufai

2016-01-01

The study explored the curriculum guidelines and primary school teachers' conceptions and practices of the Multiple Solutions Approach (MSA) in teaching mathematics using basic qualitative research design. Informal conversation interviews (ICIs), observations, video and document analyses were used to collect data. Participants included a purposive…

Getting a Bead on It

ERIC Educational Resources Information Center

Ferrucci, Beverly J.; McDougall, Jennifer; Carter, Jack

2009-01-01

One challenge that middle school teachers commonly face is finding insightful, hands-on applications when teaching basic mathematical concepts. One concept that is a foundation of middle school mathematics is the notion of "linear functions." Although a variety of models can be used for linear equations, such as temperature conversions,…

Conversion of the CTA, Inc., en route operations concepts database into a formal sentence outline job task taxonomy.

DOT National Transportation Integrated Search

1993-01-01

FAA Air Traffic Control Operations Concepts Volume VI: ARTCC-Host En Route Controllers (1990) developed by CTA, Inc., a technical description of the duties of an En Route air traffic control specialist (ATCS), formatted in User Interface Language, wa...

Collective Contexts in Conversation: Grounding by Proxy

ERIC Educational Resources Information Center

Eshghi, Arash; Healey, Patrick G. T.

2016-01-01

Anecdotal evidence suggests that participants in conversation can sometimes act as a coalition. This implies a level of conversational organization in which groups of individuals form a coherent unit. This paper investigates the implications of this phenomenon for psycholinguistic and semantic models of shared context in dialog. We present a…

Congress Inches Away from Metric Conversion

ERIC Educational Resources Information Center

Russell, Cristine

1974-01-01

Reasons are discussed concerning the House of Representatives' defeat in 1974 of a bill to establish a National Metric Conversion Board which would coordinate the process of voluntary conversion to the metric system a ten-year period. A brief history of the metric system in the United States is included. (DT)

Demonstration/Validation of the Snap Sampler Passive Ground Water Sampling Device for Sampling Inorganic Analytes at the Former Pease Air Force Base

DTIC Science & Technology

2009-07-01

viii Unit Conversion Factors...sampler is also an economic alternative for sampling for inorganic analytes. ERDC/CRREL TR-09-12 xii Unit Conversion Factors Multiply By To Obtain...head- space and then covered with two layers of tightly fitting aluminum foil. To dissolve the analytes, the solutions were stirred for approximately

Satellite Power Systems (SPS) concept definition study. Volume 4: SPS point design definition

NASA Technical Reports Server (NTRS)

Hanley, G.

1978-01-01

The satellite power systems point design concept is described. The concept definition includes satellite, ground and space systems, and their relationships. Emphasis is placed on the definition of the GaAlAs photovoltaic satellite system. The major subsystems of the satellite system including power conversion, power distribution and control, microwave, attitude control and stationkeeping, thermal control, structures, and information management and control are discussed.

Etiology, pathogenesis, and therapy according to Pierre Janet concerning conversion disorders and dissociative disorders.

PubMed

Bühler, Karl-Ernst; Heim, Gerhard

2011-01-01

Pierre Janet's works on conversion disorders or dissociative disorders has mainly fallen to the wayside in favour of Freud's works. In the first part of this paper, Janet's conception of hysteria is discussed and his place in French psychiatry described. Different aspects of Janet's diathesis-stress approach are presented (particularly the pathogenic concept of fixed ideas), which refer not only to a conception of hysteria but also to traumatic (stress) disorders and other psychological disturbances. The second part of the paper details the varieties of Janetian therapeutic treatments of these disorders: the "liquidation" of fixed ideas by hypnosis and suggestion, confrontation techniques, which resemble contemporary cognitive behavioural approaches, and special cognitive ("logagogic") interventions. Finally, we discuss the various treatment strategies based on psychoeconomic considerations such as physical or psycho-phyical therapies, psychoeducation, treatment through rest, and simplification of life for dealing with basic disturbances of psychic disorders.

Sustainable fuel for the transportation sector

PubMed Central

Agrawal, Rakesh; Singh, Navneet R.; Ribeiro, Fabio H.; Delgass, W. Nicholas

2007-01-01

A hybrid hydrogen-carbon (H2CAR) process for the production of liquid hydrocarbon fuels is proposed wherein biomass is the carbon source and hydrogen is supplied from carbon-free energy. To implement this concept, a process has been designed to co-feed a biomass gasifier with H2 and CO2 recycled from the H2-CO to liquid conversion reactor. Modeling of this biomass to liquids process has identified several major advantages of the H2CAR process. (i) The land area needed to grow the biomass is <40% of that needed by other routes that solely use biomass to support the entire transportation sector. (ii) Whereas the literature estimates known processes to be able to produce ≈30% of the United States transportation fuel from the annual biomass of 1.366 billion tons, the H2CAR process shows the potential to supply the entire United States transportation sector from that quantity of biomass. (iii) The synthesized liquid provides H2 storage in an open loop system. (iv) Reduction to practice of the H2CAR route has the potential to provide the transportation sector for the foreseeable future, using the existing infrastructure. The rationale of using H2 in the H2CAR process is explained by the significantly higher annualized average solar energy conversion efficiency for hydrogen generation versus that for biomass growth. For coal to liquids, the advantage of H2CAR is that there is no additional CO2 release to the atmosphere due to the replacement of petroleum with coal, thus eliminating the need to sequester CO2. PMID:17360377

Sustainable fuel for the transportation sector.

PubMed

Agrawal, Rakesh; Singh, Navneet R; Ribeiro, Fabio H; Delgass, W Nicholas

2007-03-20

A hybrid hydrogen-carbon (H(2)CAR) process for the production of liquid hydrocarbon fuels is proposed wherein biomass is the carbon source and hydrogen is supplied from carbon-free energy. To implement this concept, a process has been designed to co-feed a biomass gasifier with H(2) and CO(2) recycled from the H(2)-CO to liquid conversion reactor. Modeling of this biomass to liquids process has identified several major advantages of the H(2)CAR process. (i) The land area needed to grow the biomass is <40% of that needed by other routes that solely use biomass to support the entire transportation sector. (ii) Whereas the literature estimates known processes to be able to produce approximately 30% of the United States transportation fuel from the annual biomass of 1.366 billion tons, the H(2)CAR process shows the potential to supply the entire United States transportation sector from that quantity of biomass. (iii) The synthesized liquid provides H(2) storage in an open loop system. (iv) Reduction to practice of the H(2)CAR route has the potential to provide the transportation sector for the foreseeable future, using the existing infrastructure. The rationale of using H(2) in the H(2)CAR process is explained by the significantly higher annualized average solar energy conversion efficiency for hydrogen generation versus that for biomass growth. For coal to liquids, the advantage of H(2)CAR is that there is no additional CO(2) release to the atmosphere due to the replacement of petroleum with coal, thus eliminating the need to sequester CO(2).

Establishing a synergetic carbon utilization mechanism for non-catabolic use of glucose in microbial synthesis of trehalose.

PubMed

Wu, Yifei; Sun, Xinxiao; Lin, Yuheng; Shen, Xiaolin; Yang, Yaping; Jain, Rachit; Yuan, Qipeng; Yan, Yajun

2017-01-01

In nature glucose is a common carbon and energy source for catabolic use and also a building unit of polysaccharides and glycosylated compounds. The presence of strong glucose catabolic pathways in microorganism rapidly decomposes glucose into smaller metabolites and challenges non-catabolic utilization of glucose as C6 building unit or precursor. To address this dilemma, we design a synergetic carbon utilization mechanism (SynCar), in which glucose catabolism is inactivated and a second carbon source (e.g. glycerol) is employed to maintain cell growth and rationally strengthen PEP driving force for glucose uptake and non-catabolic utilization. Remarkably, a trehalose biosynthesis model developed for proof-of-concept indicates that SynCar leads to 131% and 200% improvement in trehalose titer and yield, respectively. The conversion rate of glucose to trehalose reaches 91% of the theoretical maximum. This work demonstrates the broad applicability of SynCar in the biosynthesis of molecules derived from non-catabolic glucose. Copyright © 2016 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

The Barrett's Gland in Phenotype Space.

PubMed

McDonald, Stuart A C; Graham, Trevor A; Lavery, Danielle L; Wright, Nicholas A; Jansen, Marnix

2015-01-01

Barrett's esophagus is characterized by the erosive replacement of esophageal squamous epithelium by a range of metaplastic glandular phenotypes. These glandular phenotypes likely change over time, and their distribution varies along the Barrett's segment. Although much recent work has addressed Barrett's esophagus from the genomic viewpoint-its genotype space- the fact that the phenotype of Barrett's esophagus is nonstatic points to conversion between phenotypes and suggests that Barrett's esophagus also exists in phenotype space . Here we explore this latter concept, investigating the scope of glandular phenotypes in Barrett's esophagus and how they exist in physical and temporal space as well as their evolution and their life history. We conclude that individual Barrett's glands are clonal units; because of this important fact, we propose that it is the Barrett's gland that is the unit of selection in phenotypic and indeed neoplastic progression. Transition between metaplastic phenotypes may be governed by neutral drift akin to niche turnover in normal and dysplastic niches. In consequence, the phenotype of Barrett's glands assumes considerable importance, and we make a strong plea for the integration of the Barrett's gland in both genotype and phenotype space in future work.

Enriching student concept images: Teaching and learning fractions through a multiple-embodiment approach

NASA Astrophysics Data System (ADS)

Zhang, Xiaofen; Clements, M. A. (Ken); Ellerton, Nerida F.

2015-06-01

This study investigated how fifth-grade children's concept images of the unit fractions represented by the symbols , , and changed as a result of their participation in an instructional intervention based on multiple embodiments of fraction concepts. The participants' concept images were examined through pre- and post-teaching written questions and pre- and post-teaching one-to-one verbal interview questions. Results showed that at the pre-teaching stage, the student concept images of unit fractions were very narrow and mainly linked to area models. However, after the instructional intervention, the fifth graders were able to select and apply a variety of models in response to unit fraction tasks, and their concept images of unit fractions were enriched and linked to capacity, perimeter, linear and discrete models, as well as to area models. Their performances on tests had improved, and their conceptual understandings of unit fractions had developed.

The energy crisis and energy from the sun; Proceedings of the Symposium on Solar Energy Utilization, Washington, D.C., April 30, 1974

NASA Technical Reports Server (NTRS)

Thekaekara, M. P.

1974-01-01

Papers on the state of the art and future prospects of solar energy utilization in the United States are included. Research and technologies for heating and cooling of buildings, solar thermal energy conversion, photovoltaic conversion, biomass production and conversion, wind energy conversion and ocean thermal energy conversion are covered. The increasing funding of the National Solar Energy Program is noted. Individual items are announced in this issue.

CLABSI Conversations: Lessons From Peer-to-Peer Assessments to Reduce Central Line-Associated Bloodstream Infections.

PubMed

Pham, Julius Cuong; Goeschel, Christine A; Berenholtz, Sean M; Demski, Renee; Lubomski, Lisa H; Rosen, Michael A; Sawyer, Melinda D; Thompson, David A; Trexler, Polly; Weaver, Sallie J; Weeks, Kristina R; Pronovost, Peter J

2016-01-01

A national collaborative helped many hospitals dramatically reduce central line-associated bloodstream infections (CLABSIs), but some hospitals struggled to reduce infection rates. This article describes the development of a peer-to-peer assessment process (CLABSI Conversations) and the practical, actionable practices we discovered that helped intensive care unit teams achieve a CLABSI rate of less than 1 infection per 1000 catheter-days for at least 1 year. CLABSI Conversations was designed as a learning-oriented process, in which a team of peers visited hospitals to surface barriers to infection prevention and to share best practices and insights from successful intensive care units. Common practices led to 10 recommendations: executive and board leaders communicate the goal of zero CLABSI throughout the hospital; senior and unit-level leaders hold themselves accountable for CLABSI rates; unit physicians and nurse leaders own the problem; clinical leaders and infection preventionists build infection prevention training and simulation programs; infection preventionists participate in unit-based CLABSI reduction efforts; hospital managers make compliance with best practices easy; clinical leaders standardize the hospital's catheter insertion and maintenance practices and empower nurses to stop any potentially harmful acts; unit leaders and infection preventionists investigate CLABSIs to identify root causes; and unit nurses and staff audit catheter maintenance policies and practices.

Twenty years of oxygenated treatment on Russian supercritical plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shitsman, M.E.

1995-01-01

The oxygenated treatment (OT) in Russia was first (1973-74) introduced at the 300 MWe Konakovo Supercritical units (SCU). The advantage of OT over AVT especially in rising the reliability of low-radiation boiler section (LRS) promoted to conversion the working units on OT and putting into operation the new SCUs directly with OT. All Russian supercritical plants, besides two of them, operate currently with OT. The conversion of units on OT doesn`t demand much expenditures. OT is simple and reliable. The OT introduction makes the main difficulty connected with the existance of stable stereotype for ammonia feed and supporting the oxygenmore » concentration in feedwater less than 5 ppb. The staff of two mentioned plants gave proof of devotion to AVT by its wide application in the USA and Japan. Now the units with once through boilers at these countries are intensively conversed on OT. It is possible to hope that this circumstance will dismiss at last the stereotype of oxygen fear.« less

Psychiatric symptoms and dissociation in conversion, somatization and dissociative disorders.

PubMed

Espirito-Santo, Helena; Pio-Abreu, Jose Luis

2009-03-01

Conversion, dissociation and somatization are historically related in the long established concept of hysteria. Somewhere along the way they were separated due to the Cartesian dualistic view. The aim of the present study was to compare these pathologies and investigate whether symptoms of these pathologies overlap in their clinical appearance in a Portuguese sample. Twenty-six patients with conversion disorder, 38 with dissociative disorders, 40 with somatization disorder, and a comparison group of 46 patients having other psychiatric disorders answered questions about dissociation (Dissociative Experiences Scale), somatoform dissociation (Somatoform Dissociation Questionnaire), and psychopathological symptoms (Brief Symptom Inventory). Dissociative and somatoform symptoms were significantly more frequent in dissociative and conversion disorder than in somatization disorder and controls. There were no significant differences between dissociative and conversion patients. Conversion disorder is closely related to dissociative disorders. These results support the ICD-10 categorization of conversion disorder among dissociative disorders and the hypothesis of analogous psychopathological processes in conversion and dissociative disorders versus somatization disorder.

Edwin I. Hatch nuclear plant implementation of improved technical specifications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahler, S.R.; Pendry, D.

1994-12-31

Edwin I. Hatch nuclear plant consists of two General Electric boiling water reactor/4 units, with a common control room and a common refueling floor. In March 1993, Hatch began conversion of both units` technical specifications utilizing NUREG 1433. The technical specifications amendment request was submitted February 25, 1994. Issuance is scheduled for October 21, 1994, with implementation on March 15, 1994. The current unit-1 technical specifications are in the {open_quotes}custom{close_quotes} format, and the unit-2 technical specifications are in the old standard format. Hatch previously relocated the fire protection and radiological technical specifications requirements. The Hatch conversion will provide consistency betweenmore » the two units, to the extent practicable.« less

75 FR 31461 - Notice of Submission of Proposed Information Collection to OMB; Emergency Comment Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-03

... Proposed Information Collection to OMB; Emergency Comment Request; Conversion of Efficiencies Units to One... via Housing Notice and attached forms to permit the conversion of efficiencies to one-bedrooms provided it can be demonstrated that the conversion is warranted by local demands and results in the long...

The Nature of Primary Students' Conversation in Technology Education

ERIC Educational Resources Information Center

Fox-Turnbull, Wendy H.

2016-01-01

Classroom conversations are core to establishing successful learning for students. This research explores the nature of conversation in technology education in the primary classroom and the implications for teaching and learning. Over a year, two units of work in technology were taught in two primary classrooms. Most data was gathered in Round 2…

Integrating separation and conversion - Conversion of biorefinery process streams to biobased chemicals and fuels

Treesearch

Joseph J. Bozell; Berenger Biannic; Diana Cedeno; Thomas Elder; Omid Hosseinaei; Lukas Delbeck; Jae-Woo Kim; C.J. O' Lenick; Timothy Young

2014-01-01

Abstract The concept of the integrated biorefinery is critical to developing a robust biorefining industry in the USA.Within this model, the biorefinery will produce fuel as a highvolume output addressing domestic energy needs and biobased chemical products (high-value organics) as an output providing necessary economic support for fuel production. This paper will...

Feed Me! Rethinking Traditional Modes of Library Access and Content Delivery

ERIC Educational Resources Information Center

Hutchens, Chad; Clark, Jason

2008-01-01

At their core, XML feeds are content-delivery vehicles. This fact has not always been highlighted in library conversations surrounding RSS and ATOM. The authors have looked to extend the conversation by offering a proof of concept application using RSS as a means to deliver all types of library data: PDFs, docs, images, video--to people where and…

The dish-Rankine SCSTPE program (Engineering Experiment no. 1). [systems engineering and economic analysis for a small community solar thermal electric system

NASA Technical Reports Server (NTRS)

Pons, R. L.; Grigsby, C. E.

1980-01-01

Activities planned for phase 2 Of the Small Community Solar Thermal Power Experiment (PFDR) program are summarized with emphasis on a dish-Rankine point focusing distributed receiver solar thermal electric system. Major design efforts include: (1) development of an advanced concept indirect-heated receiver;(2) development of hardware and software for a totally unmanned power plant control system; (3) implementation of a hybrid digital simulator which will validate plant operation prior to field testing; and (4) the acquisition of an efficient organic Rankine cycle power conversion unit. Preliminary performance analyses indicate that a mass-produced dish-Rankine PFDR system is potentially capable of producing electricity at a levelized busbar energy cost of 60 to 70 mills per KWh and with a capital cost of about $1300 per KW.

Study of alternate space shuttle concepts

NASA Technical Reports Server (NTRS)

1971-01-01

A study of alternate space shuttle concepts was conducted to examine the stage-and-one-half concept and its potential for later conversion and use in the two stage reusable shuttle system. A study of external hydrogen tank concepts was conducted to determine the issues involved in the design and production of a low-cost expendable tank system. The major objectives of the study were to determine: (1) realistic drop tank program cost estimates, (2) estimated drop tank program cost for selected specific designs, and (3) change in program cost due to variations in design and manufacturing concepts and changes in program assumptions.

Current Trends in Metric Conversion in the United States: Potential Trouble for National Defense.

DTIC Science & Technology

1980-05-01

measures in the United States appears inevitable, but is being prolonged due to present legisla- *tion which allows each industrial sector to convert...centralized government planning and leadership toward metrication in the shortest possible time. II. Problem: Spurred by the automotive industry , voluntary...conversion among major U.S. industries is snowballing while public resistance to met- rication is stiffening. This confrontation threatens to

Development of Criteria and Procedures for Management of Classified Document Collections.

ERIC Educational Resources Information Center

Rea, Jack C.

The report describes work done in development of criteria and procedures for management of collections of classified documents. Material is presented on philosophy of operation, concept of user service, accession and retention. Much of the discussion is based upon the concept of conversion to a microfiche-oriented library; however, hard copy…

Learning Gains for Core Concepts in a Serious Game on Scientific Reasoning

ERIC Educational Resources Information Center

Forsyth, Carol; Pavlik, Philip, Jr.; Graesser, Arthur C.; Cai, Zhiqiang; Germany, Mae-lynn; Millis, Keith; Dolan, Robert P.; Butler, Heather; Halpern, Diane

2012-01-01

"OperationARIES!" is an Intelligent Tutoring System that teaches scientific inquiry skills in a game-like atmosphere. Students complete three different training modules, each with natural language conversations, in order to acquire deep-level knowledge of 21 core concepts of research methodology (e.g., correlation does not mean…

MATLAB as an incentive for student learning of skills

NASA Astrophysics Data System (ADS)

Bank, C. G.; Ghent, R. R.

2016-12-01

Our course "Computational Geology" takes a holistic approach to student learning by using MATLAB as a focal point to increase students' computing, quantitative reasoning, data analysis, report writing, and teamwork skills. The course, taught since 2007 with recent enrollments around 35 and aimed at 2nd to 3rd-year students, is required for the Geology and Earth and Environmental Systems major programs, and can be chosen as elective in our other programs, including Geophysics. The course is divided into five projects: Pacific plate velocity from the Hawaiian hotspot track, predicting CO2 concentration in the atmosphere, volume of Earth's oceans and sea-level rise, comparing wind directions for Vancouver and Squamish, and groundwater flow. Each project is based on real data, focusses on a mathematical concept (linear interpolation, gradients, descriptive statistics, differential equations) and highlights a programming task (arrays, functions, text file input/output, curve fitting). Working in teams of three, students need to develop a conceptional model to explain the data, and write MATLAB code to visualize the data and match it to their conceptional model. The programming is guided, and students work individually on different aspects (for example: reading the data, fitting a function, unit conversion) which they need to put together to solve the problem. They then synthesize their thought process in a paper. Anecdotal evidence shows that students continue using MATLAB in other courses.

Preliminary assessment of rover power systems for the Mars Rover Sample Return Mission

NASA Technical Reports Server (NTRS)

Bents, D. J.

1989-01-01

Four isotope power system concepts were presented and compared on a common basis for application to on-board electrical prime power for an autonomous planetary rover vehicle. A representative design point corresponding to the Mars Rover Sample Return (MRSR) preliminary mission requirements (500 W) was selected for comparison purposes. All systems concepts utilize the General Purpose Heat Source (GPHS) isotope heat source developed by DOE. Two of the concepts employ thermoelectric (TE) conversion: one using the GPHS Radioisotope Thermoelectric Generator (RTG) used as a reference case, the other using an advanced RTG with improved thermoelectric materials. The other two concepts employed are dynamic isotope power systems (DIPS): one using a closed Brayton cycle (CBC) turboalternator, and the other using a free piston Stirling cycle engine/linear alternator (FPSE) with integrated heat source/heater head. Near-term technology levels have been assumed for concept characterization using component technology figure-of-merit values taken from the published literature. For example, the CBC characterization draws from the historical test database accumulated from space Brayton cycle subsystems and components from the NASA B engine through the mini-Brayton rotating unit. TE system performance is estimated from Voyager/multihundred Watt (MHW)-RTG flight experience through Mod-RTG performance estimates considering recent advances in TE materials under the DOD/DOE/NASA SP-100 and NASA Committee on Scientific and Technological Information programs. The Stirling DIPS system is characterized from scaled-down Space Power Demonstrator Engine (SPDE) data using the GPHS directly incorporated into the heater head. The characterization/comparison results presented here differ from previous comparison of isotope power (made for LEO applications) because of the elevated background temperature on the Martian surface compared to LEO, and the higher sensitivity of dynamic systems to elevated s

Biological valorization of low molecular weight lignin.

PubMed

Abdelaziz, Omar Y; Brink, Daniel P; Prothmann, Jens; Ravi, Krithika; Sun, Mingzhe; García-Hidalgo, Javier; Sandahl, Margareta; Hulteberg, Christian P; Turner, Charlotta; Lidén, Gunnar; Gorwa-Grauslund, Marie F

2016-12-01

Lignin is a major component of lignocellulosic biomass and as such, it is processed in enormous amounts in the pulp and paper industry worldwide. In such industry it mainly serves the purpose of a fuel to provide process steam and electricity, and to a minor extent to provide low grade heat for external purposes. Also from other biorefinery concepts, including 2nd generation ethanol, increasing amounts of lignin will be generated. Other uses for lignin - apart from fuel production - are of increasing interest not least in these new biorefinery concepts. These new uses can broadly be divided into application of the polymer as such, native or modified, or the use of lignin as a feedstock for the production of chemicals. The present review focuses on the latter and in particular the advances in the biological routes for chemicals production from lignin. Such a biological route will likely involve an initial depolymerization, which is followed by biological conversion of the obtained smaller lignin fragments. The conversion can be either a short catalytic conversion into desired chemicals, or a longer metabolic conversion. In this review, we give a brief summary of sources of lignin, methods of depolymerization, biological pathways for conversion of the lignin monomers and the analytical tools necessary for characterizing and evaluating key lignin attributes. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Radiation energy conversion in space

NASA Technical Reports Server (NTRS)

Billman, K. W.

1979-01-01

Topics discussed at the third NASA conference on radiant energy conversion are reviewed. The unconcentrated-photovoltaic-generation version of a solar power satellite is described, noting that it will consist of a 21.3 x 5.3-sq-km silicon-solar-cell array expected to provide 17 Gw of electrical power, with 1 km in diam transmitters oriented to beam 2.45 GHz microwave power to two receiving/rectifying 'rectennas' on earth. The Solares space-energy-system concept, designed for providing a large fraction of the world's energy needs at costs comparable to those of future coal/nuclear alternative, is considered, as are subsystems for improving the economics of the solar power satellite. A concept proposing the use of relativistic-electron-storage rings for electron-beam energy transmission and storage, and a report on the production of a high temperature plasma with concentrated solar radiation are taken into account. Laser-conversion systems, including the direct-solar-pumped space laser, and the telec-powered spacecraft, are discussed.

Aqueous Lithium-Iodine Solar Flow Battery for the Simultaneous Conversion and Storage of Solar Energy.

PubMed

Yu, Mingzhe; McCulloch, William D; Beauchamp, Damian R; Huang, Zhongjie; Ren, Xiaodi; Wu, Yiying

2015-07-08

Integrating both photoelectric-conversion and energy-storage functions into one device allows for the more efficient solar energy usage. Here we demonstrate the concept of an aqueous lithium-iodine (Li-I) solar flow battery (SFB) by incorporation of a built-in dye-sensitized TiO2 photoelectrode in a Li-I redox flow battery via linkage of an I3(-)/I(-) based catholyte, for the simultaneous conversion and storage of solar energy. During the photoassisted charging process, I(-) ions are photoelectrochemically oxidized to I3(-), harvesting solar energy and storing it as chemical energy. The Li-I SFB can be charged at a voltage of 2.90 V under 1 sun AM 1.5 illumination, which is lower than its discharging voltage of 3.30 V. The charging voltage reduction translates to energy savings of close to 20% compared to conventional Li-I batteries. This concept also serves as a guiding design that can be extended to other metal-redox flow battery systems.

Radioactive Waste Management at the New Conversion Facility of 'TVEL'{sup R} Fuel Company - 13474

DOE Office of Scientific and Technical Information (OSTI.GOV)

Indyk, S.I.; Volodenko, A.V.; Tvilenev, K.A.

2013-07-01

The project on the new conversion facility construction is being implemented by Joint Stock Company (JSC) 'Siberian Group of Chemical Enterprises' (SGChE) within TVEL{sup R} Fuel Company. The objective is to construct the up-to-date facility ensuring the industrial and environmental safety with the reduced impact on the community and environment in compliance with the Russian new regulatory framework on radioactive waste (RW) management. The history of the SGChE development, as well as the concepts and approaches to RW management implemented by now are shown. The SGChE future image is outlined, together with its objectives and concept on RW management inmore » compliance with the new act 'On radioactive waste management' adopted in Russia in 2011. Possible areas of cooperation with international companies are discussed in the field of RW management with the purpose of deploying the best Russian and world practices on RW management at the new conversion facility. (authors)« less

Radiation energy conversion in space

DOE Office of Scientific and Technical Information (OSTI.GOV)

Billman, K.W.

1979-03-01

Topics discussed at the third NASA conference on radiant energy conversion are reviewed. The unconcentrated-photovoltaic-generation version of a solar power satellite is described, noting that it will consist of a 21.3 x 5.3-sq-km silicon-solar-cell array expected to provide 17 Gw of electrical power, with 1 km in diam transmitters oriented to beam 2.45 GHz microwave power to two receiving/rectifying 'rectennas' on earth. The Solares space-energy-system concept, designed for providing a large fraction of the world's energy needs at costs comparable to those of future coal/nuclear alternative, is considered, as are subsystems for improving the economics of the solar power satellite.more » A concept proposing the use of relativistic-electron-storage rings for electron-beam energy transmission and storage, and a report on the production of a high temperature plasma with concentrated solar radiation are taken into account. Laser-conversion systems, including the direct-solar-pumped space laser, and the telec-powered spacecraft, are discussed.« less

Cold-end Subsystem Testing for the Fission Power System Technology Demonstration Unit

NASA Technical Reports Server (NTRS)

Briggs, Maxwell; Gibson, Marc; Ellis, David; Sanzi, James

2013-01-01

The Fission Power System (FPS) Technology Demonstration Unit (TDU) consists of a pumped sodium-potassium (NaK) loop that provides heat to a Stirling Power Conversion Unit (PCU), which converts some of that heat into electricity and rejects the waste heat to a pumped water loop. Each of the TDU subsystems is being tested independently prior to full system testing at the NASA Glenn Research Center. The pumped NaK loop is being tested at NASA Marshall Space Flight Center; the Stirling PCU and electrical controller are being tested by Sunpower Inc.; and the pumped water loop is being tested at Glenn. This paper describes cold-end subsystem setup and testing at Glenn. The TDU cold end has been assembled in Vacuum Facility 6 (VF 6) at Glenn, the same chamber that will be used for TDU testing. Cold-end testing in VF 6 will demonstrate functionality; validated cold-end fill, drain, and emergency backup systems; and generated pump performance and system pressure drop data used to validate models. In addition, a low-cost proof-of concept radiator has been built and tested at Glenn, validating the design and demonstrating the feasibility of using low-cost metal radiators as an alternative to high-cost composite radiators in an end-to-end TDU test.

Cold-End Subsystem Testing for the Fission Power System Technology Demonstration Unit

NASA Technical Reports Server (NTRS)

Briggs, Mazwell; Gibson, Marc; Ellis, David; Sanzi, James

2013-01-01

The Fission Power System (FPS) Technology Demonstration Unit (TDU) consists of a pumped sodiumpotassium (NaK) loop that provides heat to a Stirling Power Conversion Unit (PCU), which converts some of that heat into electricity and rejects the waste heat to a pumped water loop. Each of the TDU subsystems is being tested independently prior to full system testing at the NASA Glenn Research Center. The pumped NaK loop is being tested at NASA Marshall Space Flight Center; the Stirling PCU and electrical controller are being tested by Sunpower Inc.; and the pumped water loop is being tested at Glenn. This paper describes cold-end subsystem setup and testing at Glenn. The TDU cold end has been assembled in Vacuum Facility 6 (VF 6) at Glenn, the same chamber that will be used for TDU testing. Cold-end testing in VF 6 will demonstrate functionality; validated coldend fill, drain, and emergency backup systems; and generated pump performance and system pressure drop data used to validate models. In addition, a low-cost proof-of concept radiator has been built and tested at Glenn, validating the design and demonstrating the feasibility of using low-cost metal radiators as an alternative to highcost composite radiators in an end-to-end TDU test.

Design and Test Plans for a Non-Nuclear Fission Power System Technology Demonstration Unit

NASA Technical Reports Server (NTRS)

Mason, Lee; Palac, Donald; Gibson, Marc; Houts, Michael; Warren, John; Werner, James; Poston, David; Qualls, Arthur Lou; Radel, Ross; Harlow, Scott

2012-01-01

A joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) team is developing concepts and technologies for affordable nuclear Fission Power Systems (FPSs) to support future exploration missions. A key deliverable is the Technology Demonstration Unit (TDU). The TDU will assemble the major elements of a notional FPS with a non-nuclear reactor simulator (Rx Sim) and demonstrate system-level performance in thermal vacuum. The Rx Sim includes an electrical resistance heat source and a liquid metal heat transport loop that simulates the reactor thermal interface and expected dynamic response. A power conversion unit (PCU) generates electric power utilizing the liquid metal heat source and rejects waste heat to a heat rejection system (HRS). The HRS includes a pumped water heat removal loop coupled to radiator panels suspended in the thermal-vacuum facility. The basic test plan is to subject the system to realistic operating conditions and gather data to evaluate performance sensitivity, control stability, and response characteristics. Upon completion of the testing, the technology is expected to satisfy the requirements for Technology Readiness Level 6 (System Demonstration in an Operational and Relevant Environment) based on the use of high-fidelity hardware and prototypic software tested under realistic conditions and correlated with analytical predictions.

Design and Test Plans for a Non-Nuclear Fission Power System Technology Demonstration Unit

NASA Astrophysics Data System (ADS)

Mason, L.; Palac, D.; Gibson, M.; Houts, M.; Warren, J.; Werner, J.; Poston, D.; Qualls, L.; Radel, R.; Harlow, S.

A joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) team is developing concepts and technologies for affordable nuclear Fission Power Systems (FPSs) to support future exploration missions. A key deliverable is the Technology Demonstration Unit (TDU). The TDU will assemble the major elements of a notional FPS with a non-nuclear reactor simulator (Rx Sim) and demonstrate system-level performance in thermal vacuum. The Rx Sim includes an electrical resistance heat source and a liquid metal heat transport loop that simulates the reactor thermal interface and expected dynamic response. A power conversion unit (PCU) generates electric power utilizing the liquid metal heat source and rejects waste heat to a heat rejection system (HRS). The HRS includes a pumped water heat removal loop coupled to radiator panels suspended in the thermal-vacuum facility. The basic test plan is to subject the system to realistic operating conditions and gather data to evaluate performance sensitivity, control stability, and response characteristics. Upon completion of the testing, the technology is expected to satisfy the requirements for Technology Readiness Level 6 (System Demonstration in an Operational and Relevant Environment) based on the use of high-fidelity hardware and prototypic software tested under realistic conditions and correlated with analytical predictions.

IECEC '84: Advanced energy systems - Their role in our future; Proceedings of the Nineteenth Intersociety Energy Conversion Engineering Conference, San Francisco, CA, August 19-24, 1984. Volumes 1, 2, 3, & 4

NASA Astrophysics Data System (ADS)

Among the topics discussed are: advanced energy conversion concepts, power sources for aircraft and spacecraft, alternate fuels for industrial and vehicular applications, biomass-derived fuels, electric vehicle design and development status, electrochemical energy conversion systems, electric power generation cycles, energy-efficient industrial processes, and energy policy and system analysis. Also discussed are advanced methods for energy storage and transport, fossil fuel conversion systems, geothermal energy system development and performance, novel and advanced heat engines, hydrogen fuel-based energy systems, MHD technology development status, nuclear energy systems, solar energy conversion methods, advanced heating and cooling systems, Stirling cycle device development, terrestrial photovoltaic systems, and thermoelectric and thermionic systems.

Design of video interface conversion system based on FPGA

NASA Astrophysics Data System (ADS)

Zhao, Heng; Wang, Xiang-jun

2014-11-01

This paper presents a FPGA based video interface conversion system that enables the inter-conversion between digital and analog video. Cyclone IV series EP4CE22F17C chip from Altera Corporation is used as the main video processing chip, and single-chip is used as the information interaction control unit between FPGA and PC. The system is able to encode/decode messages from the PC. Technologies including video decoding/encoding circuits, bus communication protocol, data stream de-interleaving and de-interlacing, color space conversion and the Camera Link timing generator module of FPGA are introduced. The system converts Composite Video Broadcast Signal (CVBS) from the CCD camera into Low Voltage Differential Signaling (LVDS), which will be collected by the video processing unit with Camera Link interface. The processed video signals will then be inputted to system output board and displayed on the monitor.The current experiment shows that it can achieve high-quality video conversion with minimum board size.

[Organization of clinical emergency units. Mission and environmental factors determine the organizational concept].

PubMed

Genewein, U; Jakob, M; Bingisser, R; Burla, S; Heberer, M

2009-02-01

Mission and organization of emergency units were analysed to understand the underlying principles and concepts. The recent literature (2000-2007) on organizational structures and functional concepts of clinical emergency units was reviewed. An organizational portfolio based on the criteria specialization (presence of medical specialists on the emergency unit) and integration (integration of the emergency unit into the hospital structure) was established. The resulting organizational archetypes were comparatively assessed based on established efficiency criteria (efficiency of resource utilization, process efficiency, market efficiency). Clinical emergency units differ with regard to autonomy (within the hospital structure), range of services and service depth (horizontal and vertical integration). The "specialization"-"integration"-portfolio enabled the definition of typical organizational patterns (so-called archetypes): profit centres primarily driven by economic objectives, service centres operating on the basis of agreements with the hospital board, functional clinical units integrated into medical specialty units (e.g., surgery, gynaecology) and modular organizations characterized by small emergency teams that would call specialists immediately after triage and initial diagnostic. There is no "one fits all" concept for the organization of clinical emergency units. Instead, a number of well characterized organizational concepts are available enabling a rational choice based on a hospital's mission and demand.

Experimental Investigations from the Operation of a 2 Kw Brayton Power Conversion Unit and a Xenon Ion Thruster

NASA Technical Reports Server (NTRS)

Mason, Lee; Birchenough, Arthur; Pinero, Luis

2004-01-01

A 2 kW Brayton Power Conversion Unit (PCU) and a xenon ion thruster were integrated with a Power Management and Distribution (PMAD) system as part of a Nuclear Electric Propulsion (NEP) Testbed at NASA's Glenn Research Center. Brayton converters and ion thrusters are potential candidates for use on future high power NEP missions such as the proposed Jupiter Icy Moons Orbiter (JIMO). The use of existing lower power test hardware provided a cost-effective means to investigate the critical electrical interface between the power conversion system and ion propulsion system. The testing successfully demonstrated compatible electrical operations between the converter and the thruster, including end-to-end electric power throughput, high efficiency AC to DC conversion, and thruster recycle fault protection. The details of this demonstration are reported herein.

Experimental Investigation from the Operation of a 2 kW Brayton Power Conversion Unit and a Xenon Ion Thruster

NASA Technical Reports Server (NTRS)

Hervol, David; Mason, Lee; Birchenough, Art; Pinero, Luis

2004-01-01

A 2kW Brayton Power Conversion Unit (PCU) and a xenon ion thruster were integrated with a Power Management and Distribution (PMAD) system as part of a Nuclear Electric Propulsion (NEP) Testbed at NASA's Glenn Research Center. Brayton Converters and ion thrusters are potential candidates for use on future high power NEP mission such as the proposed Jupiter Icy Moons Orbiter (JIMO). The use of a existing lower power test hardware provided a cost effective means to investigate the critical electrical interface between the power conversion system and the propulsion system. The testing successfully demonstrated compatible electrical operations between the converter and the thruster, including end-to-end electric power throughput, high efficiency AC to DC conversion, and thruster recycle fault protection. The details of this demonstration are reported herein.

[George Herbert Mead. Thought as the conversation of interior gestures].

PubMed

Quéré, Louis

2010-01-01

For George Herbert Mead, thinking amounts to holding an "inner conversation of gestures ". Such a conception does not seem especially original at first glance. What makes it truly original is the "social-behavioral" approach of which it is a part, and, particularly, two ideas. The first is that the conversation in question is a conversation of gestures or attitudes, and the second, that thought and reflexive intelligence arise from the internalization of an external process supported by the social mechanism of communication: that of conduct organization. It imports then to understand what distinguishes such ideas from those of the founder of behavioral psychology, John B. Watson, for whom thinking amounts to nothing other than subvocal speech.

Motor and somatosensory conversion disorder: a functional unawareness syndrome?

PubMed

Perez, David L; Barsky, Arthur J; Daffner, Kirk; Silbersweig, David A

2012-01-01

Although conversion disorder is closely connected to the origins of neurology and psychiatry, it remains poorly understood. In this article, the authors discuss neural and clinical parallels between lesional unawareness disorders and unilateral motor and somatosensory conversion disorder, emphasizing functional neuroimaging/disease correlates. Authors suggest that a functional-unawareness neurobiological framework, mediated by right hemisphere-lateralized, large-scale brain network dysfunction, may play a significant role in the neurobiology of conversion disorder. The perigenual anterior cingulate and the posterior parietal cortices are detailed as important in disease pathophysiology. Further investigations will refine the functional-unawareness concept, clarify the role of affective circuits, and delineate the process through which functional neurologic symptoms emerge.

James Albert Michener (1907-97): Educator, Textbook Editor, Journalist, Novelist, and Educational Philanthropist--An Imaginary Conversation.

ERIC Educational Resources Information Center

Parker, Franklin; Parker, Betty

This paper presents an imaginary conversation between an interviewer and the novelist, James Michener (1907-1997). Starting with Michener's early life experiences in Doylestown (Pennsylvania), the conversation includes his family's poverty, his wanderings across the United States, and his reading at the local public library. The dialogue includes…

Conversion from non-orthogonally to orthogonally polarized optical single-sideband modulation using optically injected semiconductor lasers.

PubMed

Hung, Yu-Han; Tseng, Chin-Hao; Hwang, Sheng-Kwang

2018-06-01

This Letter investigates an optically injected semiconductor laser for conversion from non-orthogonally to orthogonally polarized optical single-sideband modulation. The underlying mechanism relies solely on nonlinear laser characteristics and, thus, only a typical semiconductor laser is required as the key conversion unit. This conversion can be achieved for a broadly tunable frequency range up to at least 65 GHz. After conversion, the microwave phase quality, including linewidth and phase noise, is mostly preserved, and simultaneous microwave amplification up to 23 dB is feasible.

Silicon Nanowire/Polymer Hybrid Solar Cell-Supercapacitor: A Self-Charging Power Unit with a Total Efficiency of 10.5.

PubMed

Liu, Ruiyuan; Wang, Jie; Sun, Teng; Wang, Mingjun; Wu, Changsheng; Zou, Haiyang; Song, Tao; Zhang, Xiaohong; Lee, Shuit-Tong; Wang, Zhong Lin; Sun, Baoquan

2017-07-12

An integrated self-charging power unit, combining a hybrid silicon nanowire/polymer heterojunction solar cell with a polypyrrole-based supercapacitor, has been demonstrated to simultaneously harvest solar energy and store it. By efficiency enhancement of the hybrid nanowire solar cells and a dual-functional titanium film serving as conjunct electrode of the solar cell and supercapacitor, the integrated system is able to yield a total photoelectric conversion to storage efficiency of 10.5%, which is the record value in all the integrated solar energy conversion and storage system. This system may not only serve as a buffer that diminishes the solar power fluctuations from light intensity, but also pave its way toward cost-effective high efficiency self-charging power unit. Finally, an integrated device based on ultrathin Si substrate is demonstrated to expand its feasibility and potential application in flexible energy conversion and storage devices.

Fusion Ignition Rocket Engine with Ballistic Ablative Lithium Liner

NASA Technical Reports Server (NTRS)

Martin, Adam; Eskridge, Richard; Fimognari, Peter J., III.

2005-01-01

Thermo-nuclear fusion may be the key to a high Isp, high specific power (low alpha) propulsion system. In a fusion system energy is liberated within, and imparted directly to, the propellant. In principle, this can overcome the performance limitations inherent in systems that require thermal power transfer across a material boundary, and/or multiple power conversion stages (NTR, NEP). A thermo-nuclear propulsion system, which attempts to overcome some of the problems inherent in the ORION concept, is described. A passive tapered liner is launched behind a vehicle, through a hole in a pusher-plate, that is connected to the vehicle by a shock-absorbing mechanism. A dense FRC plasmoid is then accelerated to high velocity (in excess of 1,000 km/s) and shot through the hole into the liner, when it has reached a given point down-range. The kinetic energy of the FRC is converted into thermal and magnetic-field energy, igniting a fusion bum in the magnetically confined plasma. The fusion reaction serves as an ignition source for the liner, which is made out of detonable materials. The energy liberated in this process is converted to thrust by the pusher-plate, as in the classic ORION concept. However with this concept, the vehicle does not carry a magazine of pre-fabricated pulse-units. A magnetic nozzle may also be used, in place of the pusher-plate. Estimates of the conditions needed to achieve a sufficient gain will be presented, along with a description of the driver characteristics. The incorporation of this concept into the propulsion system of a spacecraft will also be discussed.

Design considerations for space radiators based on the liquid sheet (LSR) concept

NASA Technical Reports Server (NTRS)

Juhasz, Albert J.; Chubb, Donald L.

1991-01-01

Concept development work on space heat rejection subsystems tailored to the requirements of various space power conversion systems is proceeding over a broad front of technologies at NASA LeRC. Included are orbital and planetary surface based radiator concepts utilizing pumped loops, a variety of heat pipe radiator concepts, and the innovative liquid sheet radiator (LSR). The basic feasibility of the LSR concept was investigated in prior work which generated preliminary information indicating the suitability of the LSR concept for space power systems requiring cycle reject heat to be radiated to the space sink at low-to-mid temperatures (300 to 400 K), with silicon oils used for the radiator working fluid. This study is directed at performing a comparative examination of LSR characteristics as they affect the basic design of low earth orbit solar dynamic power conversion systems. The power systems considered were based on the closed Brayton (CBC) and the Free Piston Stirling (FPS) cycles, each with a power output of 2 kWe and using previously tested silicone oil (Dow-Corning Me2) as the radiator working fluid. Conclusions indicate that, due to its ability for direct cold end cooling, an LSR based heat rejection subsystem is far more compatible with a Stirling space power system than with a CBC, which requires LSR coupling by means of an intermediate gas/liquid heat exchanger and adjustment of cycle operating conditions.

Ecological units: definitions and application.

PubMed

Jax, Kurt

2006-09-01

Concepts of ecological units, such as population, community, and ecosystem, are at the basis of ecological theory and research and have increasingly become the focus of conservation strategies. Concepts of these units still suffer from inconsistencies and confusions over terminology. The different concepts are treated here together as a common "conceptual cluster," with similar ecological functions (roles) and similar problems in their definition and use. An analysis of the multitude of existing terms and concepts that have been developed for these units reveals that they differ with respect to at least four basic criteria: (i) the questions as to whether they are defined statistically or via a network of interactions; (ii) if their boundaries are drawn by topographical or process-related criteria; (iii) how high the required internal relationships are; and (iv) if they are perceived as "real" entities or abstractions by an observer The various definitions cannot be easily sorted into just a few types, but they can be characterized by several independent criteria. I argue that serious problems arise if the different possibilities of defining ecological units are not recognized and if the concepts are perceived as self-evident. The different concepts of ecological units should be defined and used in a philosophically informed manner I propose a dual approach to the use of ecological units. Generic meanings of the main concepts (especially population, community, and ecosystem) should be retained only as heuristically useful perspectives, while specific and "operational" definitions of the concepts as units should be developed, depending on specific purposes of their use. Some thoughts on the basic requirements for such definitions and the domains of their uses are briefly explained.

Are the Concepts of Dynamic Equilibrium and the Thermodynamic Criteria for Spontaneity, Nonspontaneity, and Equilibrium Compatible?

ERIC Educational Resources Information Center

Silverberg, Lee J.; Raff, Lionel M.

2015-01-01

Thermodynamic spontaneity-equilibrium criteria require that in a single-reaction system, reactions in either the forward or reverse direction at equilibrium be nonspontaneous. Conversely, the concept of dynamic equilibrium holds that forward and reverse reactions both occur at equal rates at equilibrium to the extent allowed by kinetic…

SNAP-8 power conversion system design review

NASA Technical Reports Server (NTRS)

Lopez, L. P.

1970-01-01

The conceptual design of the SNAP-8 electrical generating system configurations are reviewed including the evolution of the PCS configuration, and the current concepts. The reliabilities of two alternative PCS-G heat rejection loop configurations with two radiator design concepts are also reviewed. A computer program for calculating system pressure loss using multiple-loop flow analysis is included.

Within the Interface: Visual Rhetoric, Pedagogy, and Writing Center Website Design

ERIC Educational Resources Information Center

Myatt, Alice J.

2010-01-01

My dissertation examines the theory and praxis of taking an expanded concept of the human-computer interface (HCI) and working with the resulting concept to foster a more conversational approach for online tutoring sessions and the design of the writing center websites that facilitate online tutoring. For the purposes of my research, I describe…

Conversational Skills in a Semistructured Interview and Self-Concept in Deaf Students

ERIC Educational Resources Information Center

Silvestre, Nuria; Ramspott, Anna; Pareto, Irenka D.

2007-01-01

The starting point for this study is the importance of linguistic competence in deaf students as part of their process of socialization and the formation of their self-concept. With the 56 deaf students who participated in the research, we consider the following sociodemographic variables: age, sex and degree of hearing loss, and the educational…

Introducing High School Students to NMR Spectroscopy through Percent Composition Determination Using Low-Field Spectrometers

ERIC Educational Resources Information Center

Bonjour, Jessica L.; Pitzer, Joy M.; Frost, John A.

2015-01-01

Mole to gram conversions, density, and percent composition are fundamental concepts in first year chemistry at the high school or undergraduate level; however, students often find it difficult to engage with these concepts. We present a simple laboratory experiment utilizing portable nuclear magnetic resonance spectroscopy (NMR) to determine the…

Limited Intervention at Sub Concept of Fractions in the Object Conversion into Fractions

ERIC Educational Resources Information Center

Kurniawan, Henry; Nusantara, Toto; Subanji; Susiswo; Setiawan, Iwan; Sutawidjaja, Akbar; As'ari, Abdur Rahman; Muksar, Makbul

2016-01-01

This research is an exploratory study with a qualitative approach, which is based on interviews with a task-based the purpose of this study is to describe the understanding of elementary school students in interpreting sub concept fractions in changing of the object is given to fractions with limit intervention. While intervention on problems…

Introducing the Concept of Biocatalysis in the Classroom: The Conversion of Cholesterol to Provitamin D[subscript 3

ERIC Educational Resources Information Center

De Luca, Belén M.; Nudel, Clara B.; Gonzalez, Rodrigo H.; Nusblat, Alejandro D.

2017-01-01

Biocatalysis is a fundamental concept in biotechnology. The topic integrates knowledge of several disciplines; therefore, it was included in the course "design and optimization of biological systems" which is offered in the biochemistry curricula. We selected the ciliate tetrahymena as an example of a eukaryotic system with potential for…

Beyond the Learning Process and toward the Knowledge Creation Process: Linking Learning and Knowledge in the Supportive Learning Culture

ERIC Educational Resources Information Center

Yoon, Seung Won; Song, Ji Hoon; Lim, Doo Hun

2009-01-01

This integrative literature review synthesizes the concepts and process of organizational knowledge creation with theories of individual learning. The knowledge conversion concept (Nonaka & Takeuchi, 1995; Nonaka, Toyama, & Byosiere, 2001) is used as the basis of the organizational knowledge creation process, while major learning theories relevant…

Emerging Concept of Internationalisation in South African Higher Education: Conversations on Local and Global Exposure at the University of the Witwatersrand (Wits)

ERIC Educational Resources Information Center

Cross, Michael; Mhlanga, Ehpraim; Ojo, Emmanuel

2011-01-01

Rather than paying attention to the specific approaches emerging from different contexts, current debates tend to privilege Western-universalizing concepts of internationalisation, unproblematically accepted as globally established truths. In South Africa, where the legacy of isolation and the dominance of Eurocentricism in academia have inspired…

Assessment of nuclear reactor concepts for low power space applications

NASA Technical Reports Server (NTRS)

Klein, Andrew C.; Gedeon, Stephen R.; Morey, Dennis C.

1988-01-01

The results of a preliminary small reactor concepts feasibility and safety evaluation designed to provide a first order validation of the nuclear feasibility and safety of six small reactor concepts are given. These small reactor concepts have potential space applications for missions in the 1 to 20 kWe power output range. It was concluded that low power concepts are available from the U.S. nuclear industry that have the potential for meeting both the operational and launch safety space mission requirements. However, each design has its uncertainties, and further work is required. The reactor concepts must be mated to a power conversion technology that can offer safe and reliable operation.

Strategic supply system design - a holistic evaluation of operational and production cost for a biorefinery supply chain

DOE PAGES

Lamers, Patrick; Tan, Eric C. D.; Searcy, Erin M.; ...

2015-08-20

Here, pioneer cellulosic biorefineries across the United States rely on a conventional feedstock supply system based on one-year contracts with local growers, who harvest, locally store, and deliver feed-stock in low-density format to the conversion facility. While the conventional system is designed for high biomass yield areas, pilot scale operations have experienced feedstock supply shortages and price volatilities due to reduced harvests and competition from other industries. Regional supply dependency and the inability to actively manage feedstock stability and quality, provide operational risks to the biorefinery, which translate into higher investment risk. The advanced feedstock supply system based on amore » network of depots can mitigate many of these risks and enable wider supply system benefits. This paper compares the two concepts from a system-level perspective beyond mere logistic costs. It shows that while processing operations at the depot increase feedstock supply costs initially, they enable wider system benefits including supply risk reduction (leading to lower interest rates on loans), industry scale-up, conversion yield improvements, and reduced handling equipment and storage costs at the biorefinery. When translating these benefits into cost reductions per liter of gasoline equivalent (LGE), we find that total cost reductions between -0.46 to -0.21 per LGE for biochemical and -0.32 to -0.12 per LGE for thermochemical conversion pathways are possible. Naturally, these system level benefits will differ between individual actors along the feedstock supply chain. Further research is required with respect to depot sizing, location, and ownership structures.« less

Strategic supply system design - a holistic evaluation of operational and production cost for a biorefinery supply chain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamers, Patrick; Tan, Eric C. D.; Searcy, Erin M.

Here, pioneer cellulosic biorefineries across the United States rely on a conventional feedstock supply system based on one-year contracts with local growers, who harvest, locally store, and deliver feed-stock in low-density format to the conversion facility. While the conventional system is designed for high biomass yield areas, pilot scale operations have experienced feedstock supply shortages and price volatilities due to reduced harvests and competition from other industries. Regional supply dependency and the inability to actively manage feedstock stability and quality, provide operational risks to the biorefinery, which translate into higher investment risk. The advanced feedstock supply system based on amore » network of depots can mitigate many of these risks and enable wider supply system benefits. This paper compares the two concepts from a system-level perspective beyond mere logistic costs. It shows that while processing operations at the depot increase feedstock supply costs initially, they enable wider system benefits including supply risk reduction (leading to lower interest rates on loans), industry scale-up, conversion yield improvements, and reduced handling equipment and storage costs at the biorefinery. When translating these benefits into cost reductions per liter of gasoline equivalent (LGE), we find that total cost reductions between -0.46 to -0.21 per LGE for biochemical and -0.32 to -0.12 per LGE for thermochemical conversion pathways are possible. Naturally, these system level benefits will differ between individual actors along the feedstock supply chain. Further research is required with respect to depot sizing, location, and ownership structures.« less

Assessment of variation in the alberta context tool: the contribution of unit level contextual factors and specialty in Canadian pediatric acute care settings

PubMed Central

2011-01-01

Background There are few validated measures of organizational context and none that we located are parsimonious and address modifiable characteristics of context. The Alberta Context Tool (ACT) was developed to meet this need. The instrument assesses 8 dimensions of context, which comprise 10 concepts. The purpose of this paper is to report evidence to further the validity argument for ACT. The specific objectives of this paper are to: (1) examine the extent to which the 10 ACT concepts discriminate between patient care units and (2) identify variables that significantly contribute to between-unit variation for each of the 10 concepts. Methods 859 professional nurses (844 valid responses) working in medical, surgical and critical care units of 8 Canadian pediatric hospitals completed the ACT. A random intercept, fixed effects hierarchical linear modeling (HLM) strategy was used to quantify and explain variance in the 10 ACT concepts to establish the ACT's ability to discriminate between units. We ran 40 models (a series of 4 models for each of the 10 concepts) in which we systematically assessed the unique contribution (i.e., error variance reduction) of different variables to between-unit variation. First, we constructed a null model in which we quantified the variance overall, in each of the concepts. Then we controlled for the contribution of individual level variables (Model 1). In Model 2, we assessed the contribution of practice specialty (medical, surgical, critical care) to variation since it was central to construction of the sampling frame for the study. Finally, we assessed the contribution of additional unit level variables (Model 3). Results The null model (unadjusted baseline HLM model) established that there was significant variation between units in each of the 10 ACT concepts (i.e., discrimination between units). When we controlled for individual characteristics, significant variation in the 10 concepts remained. Assessment of the contribution of specialty to between-unit variation enabled us to explain more variance (1.19% to 16.73%) in 6 of the 10 ACT concepts. Finally, when we assessed the unique contribution of the unit level variables available to us, we were able to explain additional variance (15.91% to 73.25%) in 7 of the 10 ACT concepts. Conclusion The findings reported here represent the third published argument for validity of the ACT and adds to the evidence supporting its use to discriminate patient care units by all 10 contextual factors. We found evidence of relationships between a variety of individual and unit-level variables that explained much of this between-unit variation for each of the 10 ACT concepts. Future research will include examination of the relationships between the ACT's contextual factors and research utilization by nurses and ultimately the relationships between context, research utilization, and outcomes for patients. PMID:21970404

Solid state recording current meter conversion

USGS Publications Warehouse

Cheng, Ralph T.; Wang, Lichen

1985-01-01

The authors describe the conversion of an Endeco-174 current meter to a solid-state recording current meter. A removable solid-state module was designed to fit in the space originally occupied by an 8-track tape cartridge. The module contains a CPU and 128 kilobytes of nonvolatile CMOS memory. The solid-state module communicates with any terminal or computer using an RS-232C interface at 4800 baud rate. A primary consideration for conversion was to keep modifications of the current meter to a minimum. The communication protocol was designed to emulate the Endeco tape translation unit, thus the need for a translation unit was eliminated and the original data reduction programs can be used without any modification. After conversion, the data recording section of the current meter contains no moving parts; the storage capacity of the module is equivalent to that of the original tape cartridge.

31 CFR 358.19 - Who is responsible for any loss resulting from the conversion of a bearer corpus missing callable...

Code of Federal Regulations, 2012 CFR

2012-07-01

... resulting from the conversion of a bearer corpus missing callable coupons? 358.19 Section 358.19 Money and... corpus missing callable coupons? The submitting depository institution shall indemnify the United States against any loss resulting from the conversion of a bearer corpus that is missing one or more associated...

31 CFR 358.19 - Who is responsible for any loss resulting from the conversion of a bearer corpus missing callable...

Code of Federal Regulations, 2011 CFR

2011-07-01

... resulting from the conversion of a bearer corpus missing callable coupons? 358.19 Section 358.19 Money and... corpus missing callable coupons? The submitting depository institution shall indemnify the United States against any loss resulting from the conversion of a bearer corpus that is missing one or more associated...

31 CFR 358.19 - Who is responsible for any loss resulting from the conversion of a bearer corpus missing callable...

Code of Federal Regulations, 2010 CFR

2010-07-01

... resulting from the conversion of a bearer corpus missing callable coupons? 358.19 Section 358.19 Money and... corpus missing callable coupons? The submitting depository institution shall indemnify the United States against any loss resulting from the conversion of a bearer corpus that is missing one or more associated...

31 CFR 358.19 - Who is responsible for any loss resulting from the conversion of a bearer corpus missing callable...

Code of Federal Regulations, 2014 CFR

2014-07-01

... resulting from the conversion of a bearer corpus missing callable coupons? 358.19 Section 358.19 Money and... corpus missing callable coupons? The submitting depository institution shall indemnify the United States against any loss resulting from the conversion of a bearer corpus that is missing one or more associated...

31 CFR 358.19 - Who is responsible for any loss resulting from the conversion of a bearer corpus missing callable...

Code of Federal Regulations, 2013 CFR

2013-07-01

... resulting from the conversion of a bearer corpus missing callable coupons? 358.19 Section 358.19 Money and... corpus missing callable coupons? The submitting depository institution shall indemnify the United States against any loss resulting from the conversion of a bearer corpus that is missing one or more associated...

78 FR 34656 - Record of Decision for the F-15 Aircraft Conversion, 144th Fighter Wing, California Air National...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... DEPARTMENT OF DEFENSE Department of the Air Force Record of Decision for the F-15 Aircraft Conversion, 144th Fighter Wing, California Air National Guard, Fresno-Yosemite International Airport Final... May 31, 2013, the United States Air Force signed the ROD for the F-15 Aircraft Conversion for the...

40 CFR 98.253 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... a flare. 0.001 = Unit conversion factor (metric tons per kilogram, mt/kg). n = Number of measurement... average. MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 pounds per square inch... (kg/kg-mole). MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 psia or 836.6...

40 CFR 98.253 - Calculating GHG emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... a flare. 0.001 = Unit conversion factor (metric tons per kilogram, mt/kg). n = Number of measurement... average. MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 pounds per square inch... (kg/kg-mole). MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 psia or 836.6...

40 CFR 98.253 - Calculating GHG emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... a flare. 0.001 = Unit conversion factor (metric tons per kilogram, mt/kg). n = Number of measurement... average. MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 pounds per square inch... (kg/kg-mole). MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 psia or 836.6...

40 CFR 98.253 - Calculating GHG emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... a flare. 0.001 = Unit conversion factor (metric tons per kilogram, mt/kg). n = Number of measurement... average. MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 pounds per square inch... (kg/kg-mole). MVC = Molar volume conversion factor (849.5 scf/kg-mole at 68 °F and 14.7 psia or 836.6...

The metric system: An introduction

NASA Astrophysics Data System (ADS)

Lumley, Susan M.

On 13 Jul. 1992, Deputy Director Duane Sewell restated the Laboratory's policy on conversion to the metric system which was established in 1974. Sewell's memo announced the Laboratory's intention to continue metric conversion on a reasonable and cost effective basis. Copies of the 1974 and 1992 Administrative Memos are contained in the Appendix. There are three primary reasons behind the Laboratory's conversion to the metric system. First, Public Law 100-418, passed in 1988, states that by the end of fiscal year 1992 the Federal Government must begin using metric units in grants, procurements, and other business transactions. Second, on 25 Jul. 1991, President George Bush signed Executive Order 12770 which urged Federal agencies to expedite conversion to metric units. Third, the contract between the University of California and the Department of Energy calls for the Laboratory to convert to the metric system. Thus, conversion to the metric system is a legal requirement and a contractual mandate with the University of California. Public Law 100-418 and Executive Order 12770 are discussed in more detail later in this section, but first they examine the reasons behind the nation's conversion to the metric system. The second part of this report is on applying the metric system.

Solid waste information and tracking system client-server conversion project management plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

May, D.L.

1998-04-15

This Project Management Plan is the lead planning document governing the proposed conversion of the Solid Waste Information and Tracking System (SWITS) to a client-server architecture. This plan presents the content specified by American National Standards Institute (ANSI)/Institute of Electrical and Electronics Engineers (IEEE) standards for software development, with additional information categories deemed to be necessary to describe the conversion fully. This plan is a living document that will be reviewed on a periodic basis and revised when necessary to reflect changes in baseline design concepts and schedules. This PMP describes the background, planning and management of the SWITS conversion.more » It does not constitute a statement of product requirements. Requirements and specification documentation needed for the SWITS conversion will be released as supporting documents.« less

Simplified conversions between specific conductance and salinity units for use with data from monitoring stations

USGS Publications Warehouse

Schemel, Laurence E.

2001-01-01

This article presents a simplified conversion to salinity units for use with specific conductance data from monitoring stations that have been normalized to a standard temperature of 25 °C and an equation for the reverse calculation. Although these previously undocumented methods have been shared with many IEP agencies over the last two decades, the sources of the equations and data are identified here so that the original literature can be accessed.

Influence of light-curing sources on polymerization reaction kinetics of a restorative system.

PubMed

D'Alpino, Paulo H P; Svizero, Nádia R; Pereira, José C; Rueggeberg, Frederick A; Carvalho, Ricardo M; Pashley, David H

2007-02-01

To determine the effect of using a variety of commercial light-curing units on polymerization of a dentin-bonding agent (Adper Single Bond) and of a resin composite (Filtek Z250). Infrared (IR) spectra were obtained kinetically at one scan/second at 2 cm(-1) resolution for a period of 5 minutes and were analyzed for: maximum conversion rate (%/s), time into exposure when maximum rate occurred (seconds), conversion at maximum rate (%), and total conversion (%) at 300 seconds by comparison of aliphatic-to-aromatic absorption IR peak ratios, before and after polymerization. Light units used were: QTH 540 mW/cm2 (XL3000); LED 750 mW/cm2 (Elipar FreeLight 2); PAC 2,130 mW/cm2 (ARC II). Exposure followed manufacturers' recommendations: dentin bonding agent for 10 seconds, RC for 20 seconds (QTH), and 10 seconds (LED and PAC). Polymerization kinetics was evaluated at the bottom surface (2.5 mm thick) for the resin composite and as a thin film for the dentin bonding agent on the diamond surface of an attenuated total reflectance accessory in the IR spectrometer. Values (n = 5) were compared using ANOVA and Tukey's pairwise post-hoc test: pre-set alpha 0.05. PAC produced the highest total conversion and conversion rate for the resin composite (P < 0.05). Total conversion was lower for dentin bonding adhesive using PAC than with LED or QTH (P < 0.05). LED provided the highest proportion of conversion at the maximum rate with respect to conversion at 300 seconds for both materials. QTH demonstrated the lowest maximum rate value that occurred at a longer time into exposure (P < 0.05). Polymerization kinetic parameters varied greatly between the restorative materials as well as among light-curing unit types when compared to values observed when using a QTH light as control.

Power generation based on biomass by combined fermentation and gasification--a new concept derived from experiments and modelling.

PubMed

Methling, Torsten; Armbrust, Nina; Haitz, Thilo; Speidel, Michael; Poboss, Norman; Braun-Unkhoff, Marina; Dieter, Heiko; Kempter-Regel, Brigitte; Kraaij, Gerard; Schliessmann, Ursula; Sterr, Yasemin; Wörner, Antje; Hirth, Thomas; Riedel, Uwe; Scheffknecht, Günter

2014-10-01

A new concept is proposed for combined fermentation (two-stage high-load fermenter) and gasification (two-stage fluidised bed gasifier with CO2 separation) of sewage sludge and wood, and the subsequent utilisation of the biogenic gases in a hybrid power plant, consisting of a solid oxide fuel cell and a gas turbine. The development and optimisation of the important processes of the new concept (fermentation, gasification, utilisation) are reported in detail. For the gas production, process parameters were experimentally and numerically investigated to achieve high conversion rates of biomass. For the product gas utilisation, important combustion properties (laminar flame speed, ignition delay time) were analysed numerically to evaluate machinery operation (reliability, emissions). Furthermore, the coupling of the processes was numerically analysed and optimised by means of integration of heat and mass flows. The high, simulated electrical efficiency of 42% including the conversion of raw biomass is promising for future power generation by biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

Non-phase-matched enhancement of second-harmonic generation in multilayer nonlinear structures with internal reflections.

PubMed

Centini, Marco; D'Aguanno, Giuseppe; Sciscione, Letizia; Sibilia, Concita; Bertolotti, Mario; Scalora, Michael; Bloemer, Mark J

2004-08-15

Traditional notions of second-harmonic generation rely on phase matching or quasi phase matching to achieve good conversion efficiencies. We present an entirely new concept for efficient second-harmonic generation that is based on the interference of counterpropagating waves in multilayer structures. Conversion efficiencies are an order of magnitude larger than with phase-matched second-harmonic generation in similar multilayer structures.

Teach Softly and Debunk with a Big Stick: A Response to "Evolution, Biology, and Society--A Conversation for the 21st-Century Sociology Classroom"

ERIC Educational Resources Information Center

Hanson, Chad

2010-01-01

This article presents the author's response to "Evolution, Biology, and Society: A Conversation for the 21st-Century Sociology Classroom" by Richard Machalek and Michael Martin. Their work serves as a reminder that the discipline is diverse and dynamic. The author appreciates the effort to urge sociology teachers to include genetic concepts in…

Using a Field Trip Inventory to Determine If Listening to Elementary School Students' Conversations, While on a Zoo Field Trip, Enhances Preservice Teachers' Abilities to Plan Zoo Field Trips

ERIC Educational Resources Information Center

Patrick, Patricia; Mathews, Cathy; Tunnicliffe, Sue Dale

2013-01-01

This study investigated whether listening to spontaneous conversations of elementary students and their teachers/chaperones, while they were visiting a zoo, affected preservice elementary teachers' conceptions about planning a field trip to the zoo. One hundred five preservice elementary teachers designed field trips prior to and after…

An overview of thermionic power conversion technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Morgan C.

1996-12-01

Thermionic energy conversion is one of the many concepts which make up the direct power conversion technologies. Specifically, thermionics is the process of changing heat directly into electricity via a material`s ability to emit electrons when heated. This thesis presents a broad overview of the engineering and physics necessary to make thermionic energy conversion (TEC) a practical reality. It begins with an introduction to the technology and the history of its development. This is followed by a discussion of the physics and engineering necessary to develop practical power systems. Special emphasis is placed on the critical issues which are stillmore » being researched. Finally, there is a discussion of the missions which this technology may fulfill.« less

The innovation value chain.

PubMed

Hansen, Morten T; Birkinshaw, Julian

2007-06-01

The challenges of coming up with fresh ideas and realizing profits from them are different for every company. One firm may excel at finding good ideas but may have weak systems for bringing them to market. Another organization may have a terrific process for funding and rolling out new products and services but a shortage of concepts to develop. In this article, Hansen and Birkinshaw caution executives against using the latest and greatest innovation approaches and tools without understanding the unique deficiencies in their companies' innovation systems. They offer a framework for evaluating innovation performance: the innovation value chain. It comprises the three main phases of innovation (idea generation, conversion, and diffusion) as well as the critical activities performed during those phases (looking for ideas inside your unit; looking for them in other units; looking for them externally; selecting ideas; funding them; and promoting and spreading ideas companywide). Using this framework, managers get an end-to-end view of their innovation efforts. They can pinpoint their weakest links and tailor innovation best practices appropriately to strengthen those links. Companies typically succumb to one of three broad "weakest-link" scenarios. They are idea poor, conversion poor, or diffusion poor. The article looks at the ways smart companies - including Intuit, P&G, Sara Lee, Shell, and Siemens- modify the best innovation practices and apply them to address those organizations' individual needs and flaws. The authors warn that adopting the chain-based view of innovation requires new measures of what can be delivered by each link in the chain. The approach also entails new roles for employees "external scouts" and "internal evangelists," for example. Indeed, in their search for new hires, companies should seek out those candidates who can help address particular weaknesses in the innovation value chain.

CE-SAM: a conversational interface for ISR mission support

NASA Astrophysics Data System (ADS)

Pizzocaro, Diego; Parizas, Christos; Preece, Alun; Braines, Dave; Mott, David; Bakdash, Jonathan Z.

2013-05-01

There is considerable interest in natural language conversational interfaces. These allow for complex user interactions with systems, such as fulfilling information requirements in dynamic environments, without requiring extensive training or a technical background (e.g. in formal query languages or schemas). To leverage the advantages of conversational interactions we propose CE-SAM (Controlled English Sensor Assignment to Missions), a system that guides users through refining and satisfying their information needs in the context of Intelligence, Surveillance, and Reconnaissance (ISR) operations. The rapidly-increasing availability of sensing assets and other information sources poses substantial challenges to effective ISR resource management. In a coalition context, the problem is even more complex, because assets may be "owned" by different partners. We show how CE-SAM allows a user to refine and relate their ISR information needs to pre-existing concepts in an ISR knowledge base, via conversational interaction implemented on a tablet device. The knowledge base is represented using Controlled English (CE) - a form of controlled natural language that is both human-readable and machine processable (i.e. can be used to implement automated reasoning). Users interact with the CE-SAM conversational interface using natural language, which the system converts to CE for feeding-back to the user for confirmation (e.g. to reduce misunderstanding). We show that this process not only allows users to access the assets that can support their mission needs, but also assists them in extending the CE knowledge base with new concepts.

U.S. Metric Conversion: Rough Road Ahead

ERIC Educational Resources Information Center

Guillen, Michael A.

1977-01-01

A survey of the United States' progress toward metrication indicates that, in spite of early industry and government conversion efforts, there exists significant disorientation, dissension, skepticism, and outright resistance among the influential sectors of government and private industry. (BT)

School-age children talk about chess: does knowledge drive syntactic complexity?

PubMed

Nippold, Marilyn A

2009-08-01

This study examined language productivity and syntactic complexity in school-age children in relation to their knowledge of the topic of discussion-the game of chess. Children (N = 32; mean age = 10;11 [years;months]) who played chess volunteered to be interviewed by an adult examiner who had little or no experience playing chess. Children's chess knowledge and experience was assessed, and each child was classified as a novice or an expert player. Each child participated in 3 speaking tasks: General Conversation, Chess Conversation, and Chess Explanation. Interviews were audiorecorded, transcribed into Systematic Analysis of Language Transcripts (J. F. Miller & R. Chapman, 2003), segmented into T-units, and coded for finite clauses. Each speaking task was analyzed for total T-units; mean length of T-unit; clausal density; and nominal, relative, and adverbial clause use. Total T-units, mean length of T-unit, clausal density, and the use of each type of subordinate clause was substantially higher in the Chess Explanation task compared with the Chess Conversation task or the General Conversation task. Compared with the novices, the experts knew more about chess, had played longer, and were stronger players. Nevertheless, the novices and experts did not differ on any of the language factors for any of the speaking tasks. Language productivity and syntactic complexity in school-age children are strongly influenced by the speaking task. When children are presented with a motivating and challenging topic, they rise to the occasion to explain the finer details of it to a naïve adult.

An integrated biorefinery concept for conversion of sugar beet pulp into value-added chemicals and pharmaceutical intermediates.

PubMed

Cárdenas-Fernández, Max; Bawn, Maria; Hamley-Bennett, Charlotte; Bharat, Penumathsa K V; Subrizi, Fabiana; Suhaili, Nurashikin; Ward, David P; Bourdin, Sarah; Dalby, Paul A; Hailes, Helen C; Hewitson, Peter; Ignatova, Svetlana; Kontoravdi, Cleo; Leak, David J; Shah, Nilay; Sheppard, Tom D; Ward, John M; Lye, Gary J

2017-09-21

Over 8 million tonnes of sugar beet are grown annually in the UK. Sugar beet pulp (SBP) is the main by-product of sugar beet processing which is currently dried and sold as a low value animal feed. SBP is a rich source of carbohydrates, mainly in the form of cellulose and pectin, including d-glucose (Glu), l-arabinose (Ara) and d-galacturonic acid (GalAc). This work describes the technical feasibility of an integrated biorefinery concept for the fractionation of SBP and conversion of these monosaccharides into value-added products. SBP fractionation is initially carried out by steam explosion under mild conditions to yield soluble pectin and insoluble cellulose fractions. The cellulose is readily hydrolysed by cellulases to release Glu that can then be fermented by a commercial yeast strain to produce bioethanol at a high yield. The pectin fraction can be either fully hydrolysed, using physico-chemical methods, or selectively hydrolysed, using cloned arabinases and galacturonases, to yield Ara-rich and GalAc-rich streams. These monomers can be separated using either Centrifugal Partition Chromatography (CPC) or ultrafiltration into streams suitable for subsequent enzymatic upgrading. Building on our previous experience with transketolase (TK) and transaminase (TAm) enzymes, the conversion of Ara and GalAc into higher value products was explored. In particular the conversion of Ara into l-gluco-heptulose (GluHep), that has potential therapeutic applications in hypoglycaemia and cancer, using a mutant TK is described. Preliminary studies with TAm also suggest GluHep can be selectively aminated to the corresponding chiral aminopolyol. The current work is addressing the upgrading of the remaining SBP monomer, GalAc, and the modelling of the biorefinery concept to enable economic and Life Cycle Analysis (LCA).

An Analysis of a Typical Instructional Unit in Junior High School Science to Determine the Explicit and Implicit Concept Loading Involved. Final Report.

ERIC Educational Resources Information Center

Smith, Herbert A.

This study involved examining an instructional unit with regard to its concept content and appropriateness for its target audience. The study attempted to determine (1) what concepts are treated explicitly or implicitly, (2) whether there is a hierarchical conceptual structure within the unit, (3) what level of sophistication is required to…

Projection of distributed-collector solar-thermal electric power plant economics to years 1990-2000

NASA Technical Reports Server (NTRS)

Fujita, T.; Elgabalawi, N.; Herrera, G.; Turner, R. H.

1977-01-01

A preliminary comparative evaluation of distributed-collector solar thermal power plants was undertaken by projecting power plant economics of selected systems to the 1990 to 2000 time frame. The selected systems include: (1) fixed orientation collectors with concentrating reflectors and vacuum tube absorbers, (2) one axis tracking linear concentrator including parabolic trough and variable slat designs, and (3) two axis tracking parabolic dish systems including concepts with small heat engine-electric generator assemblies at each focal point as well as approaches having steam generators at the focal point with pipeline collection to a central power conversion unit. Comparisons are presented primarily in terms of energy cost and capital cost over a wide range of operating load factors. Sensitvity of energy costs for a range of efficiency and cost of major subsystems/components is presented to delineate critical technological development needs.

[Concepts of basic physics that every cardiovascular surgeon should know: part I - mechanics of fluids].

PubMed

Oliveira, Marcos Aurélio Barboza de; Alves, Fernanda Tomé; Silva, Marcos Vinícius Pinto e; Croti, Ulisses Alexandre; Godoy, Moacir Fernandes de; Braile, Domingo Marcolino

2010-01-01

The professional activity that the cardiovascular surgeon performs is much more than a simple gesture to mechanically operate the patient's heart. There is in every act of intraoperative most notions of physiology and physics than we generally realize. This paper discusses, in the light of mathematics, on the dynamics of fluids, ie blood, focused on invasive measurements of blood pressure, the effect of vessel size on its internal resistance and the flow passing through it in conversion of various units of measurements of pressure and resistance, blood viscosity and its relationship to the vessel, hemodilution, differences in laminar and turbulent flow, velocity and blood pressure and wall tension after a stenosis and the origin of poststenotic aneurysm. This study is not to enable the reader to the knowledge of all physics, but to show it as a useful tool in explaining phenomena known in the routine of cardiovascular surgery.

Progress on 241Am Production for Use in Radioisotope Power Systems

NASA Astrophysics Data System (ADS)

Baker, S. R.; Bell, K. J.; Brown, J.; Carrigan, C.; Carrott, M. J.; Gregson, C.; Clough, M.; Maher, C. J.; Mason, C.; Rhodes, C. J.; Rice, T. G.; Sarsfield, M. J.; Stephenson, K.; Taylor, R. J.; Tinsley, T. P.; Woodhead, D. A.; Wiss, T.

2014-08-01

Electrical power sources used in outer planet missions are a key enabling technology for data acquisition and communications. Power sources generate electricity from the thermal energy from alpha decay of the radioisotope 238Pu via thermo-electric conversion. Production of 238Pu requires specialist facilities including a nuclear reactor and reprocessing plants that are expensive to build and operate, so naturally, a more economical alternative is attractive to the industry. Within Europe 241Am is a feasible alternative to 238Pu that can provide a heat source for radioisotope thermoelectric generators (RTGs) and radioisotope heating units (RHUs). As a daughter product of 241Pu decay, 241Am is present at 1000s kg levels within the UK civil plutonium stockpile.A chemical separation process is required to extract the 241Am in a pure form and this paper describes such a process, successfully developed to the proof of concept stage.

Particle-size distribution models for the conversion of Chinese data to FAO/USDA system.

PubMed

Shangguan, Wei; Dai, YongJiu; García-Gutiérrez, Carlos; Yuan, Hua

2014-01-01

We investigated eleven particle-size distribution (PSD) models to determine the appropriate models for describing the PSDs of 16349 Chinese soil samples. These data are based on three soil texture classification schemes, including one ISSS (International Society of Soil Science) scheme with four data points and two Katschinski's schemes with five and six data points, respectively. The adjusted coefficient of determination r (2), Akaike's information criterion (AIC), and geometric mean error ratio (GMER) were used to evaluate the model performance. The soil data were converted to the USDA (United States Department of Agriculture) standard using PSD models and the fractal concept. The performance of PSD models was affected by soil texture and classification of fraction schemes. The performance of PSD models also varied with clay content of soils. The Anderson, Fredlund, modified logistic growth, Skaggs, and Weilbull models were the best.

Patterns of Inequality. Unit 3, The Philosophy of Equality and Inequality. Unit 4, Personal Inequality as an Ideological Concept.

ERIC Educational Resources Information Center

Hookham, Maurice; Holloway, Clive

Open University course units are presented on the philosophy of equality and inequality (Unit 3) and on personal inequality as an ideological concept (Unit 4). The substance of Unit 3 consists of extracts from the writings of eight philosophers. The role of the philosopher in forming legitimatizing ideologies is also illustrated. The eight…

Unit conversion as a source of misclassification in US birthweight data.

PubMed

Umbach, D M

2000-01-01

This study explains why frequency polygons for US birthweights in 100-g weight classes appear spiky compared with their European counterparts. A probability model is used to describe how unit conversion can induce misclassification. Birthweights from the United States and Norway are used to illustrate that misclassification operates in grouped US data. Spikiness represents misclassification that arises when measured birthweights are rounded to the nearer ounce, converted to grams, and then grouped into weight classes. Misclassification is ameliorated, not eliminated, with 200-g weight classes. Possible biases from misclassification should be carefully evaluated when fitting statistical models to grouped US birthweights.

Design parameters for toroidal and bobbin magnetics. [conversion from English to metric units

NASA Technical Reports Server (NTRS)

Mclyman, W. T.

1974-01-01

The adoption by NASA of the metric system for dimensioning to replace long-used English units imposes a requirement on the U.S. transformer designer to convert from the familiar units to the less familiar metric equivalents. Material is presented to assist in that transition in the field of transformer design and fabrication. The conversion data makes it possible for the designer to obtain a fast and close approximation of significant parameters such as size, weight, and temperature rise. Nomographs are included to provide a close approximation for breadboarding purposes. For greater convenience, derivations of some of the parameters are also presented.

We're all here for the good of the patient: a dialogue on power.

PubMed

Kagan, Paula N; Chinn, Peggy L

2010-01-01

Two nurse scholars, whose works have centered on power and related concepts, discuss the ideas that have shaped their concepts of power. In this conversation, they reflect on factors that constrain nurses and nursing in organizations, and consider some possibilities that could lead nurses to realize their full potential and influence in the healthcare system.

Metric System versus Anthropomorphic Units. A Bicentennial Coup?

ERIC Educational Resources Information Center

Dalke, John L.

1976-01-01

A brief history of the use of the English system of measurement is provided together with a discussion of the United States conversion to the metric system. United States industries which now use the metric system are listed. (SD)

The Effective Concepts on Students' Understanding of Chemical Reactions and Energy

ERIC Educational Resources Information Center

Ayyildiz, Yildizay; Tarhan, Leman

2012-01-01

The purpose of this study was to determine the relationship between the basic concepts related to the unit of "Chemical Reactions and Energy" and the sub-concepts underlying for meaningful learning of the unit and to investigate the effectiveness of them on students' learning achievements. For this purpose, the basic concepts of the unit…

Impact of feedstock quality and variation on biochemical and thermochemical conversion

DOE PAGES

Li, Chenlin; Aston, John E.; Lacey, Jeffrey A.; ...

2016-07-21

The production of biofuels from lignocellulosic feedstock is attracting considerable attention in the United States and globally as a strategy to diversify energy resources, spur regional economic development and reduce greenhouse gas emissions. Because of the wide variation in feedstock types, compositions and content of convertible organics, there is a growing need to better understand correlations among feedstock quality attributes and conversion performance. Knowledge of the feedstock impact on conversion is essential to supply quality controlled, uniform and on-spec feedstocks to biorefineries. This review paper informs the development of meaningful feedstock quality specifications for different conversion processes. Discussions are focusedmore » on how compositional properties of feedstocks affect various unit operations in biochemical conversion processes, fast pyrolysis and hydrothermal liquefaction. In addition, future perspectives are discussed that focus on the challenges and prospects of addressing compositionally intrinsic inhibitors through feedstock preprocessing at regionally distributed depots. As a result, such preprocessing depots may allow for the commoditization of lignocellulosic feedstock and realization of stable, cost-effective and quality controlled biomass supply systems.« less

Impact of feedstock quality and variation on biochemical and thermochemical conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Chenlin; Aston, John E.; Lacey, Jeffrey A.

The production of biofuels from lignocellulosic feedstock is attracting considerable attention in the United States and globally as a strategy to diversify energy resources, spur regional economic development and reduce greenhouse gas emissions. Because of the wide variation in feedstock types, compositions and content of convertible organics, there is a growing need to better understand correlations among feedstock quality attributes and conversion performance. Knowledge of the feedstock impact on conversion is essential to supply quality controlled, uniform and on-spec feedstocks to biorefineries. This review paper informs the development of meaningful feedstock quality specifications for different conversion processes. Discussions are focusedmore » on how compositional properties of feedstocks affect various unit operations in biochemical conversion processes, fast pyrolysis and hydrothermal liquefaction. In addition, future perspectives are discussed that focus on the challenges and prospects of addressing compositionally intrinsic inhibitors through feedstock preprocessing at regionally distributed depots. As a result, such preprocessing depots may allow for the commoditization of lignocellulosic feedstock and realization of stable, cost-effective and quality controlled biomass supply systems.« less

Satellite Power System (SPS) concept definition study (Exhibit D). Volume 2: Systems/subsystems analyses

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1981-01-01

Modifications to the reference concept were studied and the best approaches defined. The impact of the high efficiency multibandgap solar array on the reference concept design is considered. System trade studies for several solid state concepts, including the sandwich concept and a separate antenna/solar concept, are described. Two solid state concepts were selected and a design definition is presented for each. Magnetrons as an alternative to the reference klystrons for dc/RF conversion are evaluated. System definitions are presented for the preferred klystron and solid state concepts. Supporting systems are analyzed, with major analysis in the microwave, structures, and power distribution areas. Results of studies for thermal control, attitude control, stationkeeping, and details of a multibandgap solar cell study are included. Advanced laser concepts and the meteorological effects of a laser beam power transmission concept are considered.

The use of computer simulations in whole-class versus small-group settings

NASA Astrophysics Data System (ADS)

Smetana, Lara Kathleen

This study explored the use of computer simulations in a whole-class as compared to small-group setting. Specific consideration was given to the nature and impact of classroom conversations and interactions when computer simulations were incorporated into a high school chemistry course. This investigation fills a need for qualitative research that focuses on the social dimensions of actual classrooms. Participants included a novice chemistry teacher experienced in the use of educational technologies and two honors chemistry classes. The study was conducted in a rural school in the south-Atlantic United States at the end of the fall 2007 semester. The study took place during one instructional unit on atomic structure. Data collection allowed for triangulation of evidence from a variety of sources approximately 24 hours of video- and audio-taped classroom observations, supplemented with the researcher's field notes and analytic journal; miscellaneous classroom artifacts such as class notes, worksheets, and assignments; open-ended pre- and post-assessments; student exit interviews; teacher entrance, exit and informal interviews. Four web-based simulations were used, three of which were from the ExploreLearning collection. Assessments were analyzed using descriptive statistics and classroom observations, artifacts and interviews were analyzed using Erickson's (1986) guidelines for analytic induction. Conversational analysis was guided by methods outlined by Erickson (1982). Findings indicated (a) the teacher effectively incorporated simulations in both settings (b) students in both groups significantly improved their understanding of the chemistry concepts (c) there was no statistically significant difference between groups' achievement (d) there was more frequent exploratory talk in the whole-class group (e) there were more frequent and meaningful teacher-student interactions in the whole-class group (f) additional learning experiences not measured on the assessment resulted from conversations and interactions in the whole-class setting (g) the potential benefits of exploratory talk in the whole-class setting were not fully realized. These findings suggest that both whole-class and small-group settings are appropriate for using computer simulations in science. The effective incorporation of simulations into whole-class instruction may provide a solution to the dilemma of technology penetration versus integration in today's classrooms.

The Quality of Teachers' Interactive Conversations with Preschool Children from Low-Income Families during Small-Group and Large-Group Activities

ERIC Educational Resources Information Center

Chen, Jennifer J.; de Groot Kim, Sonja

2014-01-01

This study examined the quality of preschool teachers' interactive conversations with three- and four-year-olds in two Head Start classrooms serving children from low-income families in the United States. Over a period of 20?weeks, 10 bi-weekly observations of conversations (totaling 15?h per classroom) were conducted in one small-group (Play…

Educative Mentoring: How a Mentor Supported a Preservice Biology Teacher's Pedagogical Content Knowledge Development

NASA Astrophysics Data System (ADS)

Barnett, Ellen; Friedrichsen, Patricia J.

2015-11-01

Research suggests discipline-specific, educative mentoring can help preservice teachers develop more sophisticated pedagogical content knowledge (PCK). However, there are few studies examining the nature of mentors' practice and how mentors influence preservice teacher's (PST) PCK. The purpose of this case study was to describe the strategies used by a secondary biology mentor teacher to support the development of a PST's PCK. The primary data sources were the transcripts of audio-recorded, daily meetings between the mentor and the PST during two curriculum units: DNA/Protein Synthesis and Evolution. The mentor influenced the PST's teaching orientation by repeatedly comparing teacher- and student-centered approaches, asking him to consider how students learn, and asking him to self-assess whether his instruction aligned with his teaching beliefs. The mentor helped the PST develop topic-specific knowledge of instructional strategies by sharing strategies she used previously, modeling critical reflection, and inviting him to critically reflect on his own instructional strategies. Topic-specific knowledge of students' understanding of science was developed by discussing common student misconceptions revealed in students' conversations and by sharing the results of test-item analysis from previous unit tests. The mentor helped develop the PST's topic-specific knowledge of assessment by helping him critically analyze and revise previous examinations to better align with the current curriculum units. Topic-specific knowledge of curricula was developed by jointly grappling with decisions about concept sequencing within units. The study includes implications for research, science teacher education, and professional development for mentors.

Program THEK energy production units of average power and using thermal conversion of solar radiation

NASA Technical Reports Server (NTRS)

1978-01-01

General studies undertaken by the C.N.R.S. in the field of solar power plants have generated the problem of building energy production units in the medium range of electrical power, in the order of 100 kW. Among the possible solutions, the principle of the use of distributed heliothermal converters has been selected as being, with the current status of things, the most advantageous solution. This principle consists of obtaining the conversion of concentrated radiation into heat by using a series of heliothermal conversion modules scattered over the ground; the produced heat is collected by a heat-carrying fluid circulating inside a thermal loop leading to a device for both regulation and storage.

United States and Russian Cooperation on Issues of Nuclear Nonproliferation

DTIC Science & Technology

2005-06-01

Reactors ( RERTR ) This project works with Russia to facilitate conversion of its research and test reactors from highly enriched uranium (HEU) fuel...reactor fuel purchase, accelerated RERTR activities, and accelerated Material Conversion and Consolidation implementation. 89 j. Fissile Materials

"I just think that we should be informed" a qualitative study of family involvement in advance care planning in nursing homes.

PubMed

Thoresen, Lisbeth; Lillemoen, Lillian

2016-11-10

As part of the research project "End-of-life Communication in Nursing Homes. Patient Preferences and Participation", we have studied how Advance Care Planning (ACP) is carried out in eight Norwegian nursing homes. The concept of ACP is a process for improving patient autonomy and communication in the context of progressive illness, anticipated deterioration and end-of-life care. While an individualistic autonomy based attitude is at the fore in most studies on ACP, there is a lack of empirical studies on how family members' participation and involvement in ACP- conversations may promote nursing home patients' participation in decisions on future treatment and end-of-life care. Based on empirical data and family ethics perspectives, the purpose of this study is to add insights to the complexity of ACP-conversations and illuminate how a family ethics perspective may improve the quality of the ACP and promote nursing home patients' participation in advance care planning. Participant observations of ACP-conversations in eight nursing homes. The observations were followed by interviews with patients and relatives together on how they experienced being part of the conversation, and expressing their views on future medical treatment, hospitalization and end-of-life issues. We found that the way nursing home patients and relatives are connected and related to each other, constitutes an intertwined unit. Further, we found that relatives' involvement and participation in ACP- conversations is significant to uncover, and give the nursing home staff insight into, what is important in the nursing home patient's life at the time. The third analytical theme is patients' and relatives' shared experiences of the dying and death of others. Drawing on past experiences can be a way of introducing or talking about death. An individual autonomy approach in advance care planning should be complemented with a family ethics approach. To be open to family ethics when planning for the patient's future in the nursing home is to be open to diversity and nuances and to the significance of the patient's former life and experiences.

Space-Based Solar Power Conversion and Delivery Systems Study. Volume 1: Executive Summary

NASA Technical Reports Server (NTRS)

1977-01-01

The research concerning space-based solar power conversion and delivery systems is summarized. The potential concepts for a photovoltaic satellite solar power system was studied with emphasis on ground output power levels of 5,000 MW and 10,000 MW. A power relay satellite, and certain aspects of the economics of these systems were also studied. A second study phase examined in greater depth the technical and economic aspects of satellite solar power systems. Throughout this study, the focus was on the economics of satellite solar power. The results indicate technical feasibility of the concept, and provide a preliminary economic justification for the first phase of a substantial development program. A development program containing test satellites is recommended. Also, development of alternative solar cell materials (other than silicon) is recommended.

Solar thermal electric power plants - Their performance characteristics and total social costs

NASA Technical Reports Server (NTRS)

Caputo, R. S.; Truscello, V. C.

1976-01-01

The central receiver (power tower) concept as a thermal conversion approach to the conversion of solar energy into electricity is compared to other solar power plant designs which feature distributed solar collection and use other types of solar collector configurations. A variety of solar thermal storage concepts are discussed and their impacts on system performance are assessed. Although a good deal of quantification is possible in a comparative study, the subjective judgments carry enormous weight in a socio-economic decision, the ultimate choice of central power plant being more a social than an economic or technical decision. Major elements of the total social cost of each type of central plant are identified as utility economic costs, R&D funds, health costs, and other relevant social impacts.

Technologies of high-performance thermography systems

NASA Astrophysics Data System (ADS)

Breiter, R.; Cabanski, Wolfgang A.; Mauk, K. H.; Kock, R.; Rode, W.

1997-08-01

A family of 2 dimensional detection modules based on 256 by 256 and 486 by 640 platinum silicide (PtSi) focal planes, or 128 by 128 and 256 by 256 mercury cadmium telluride (MCT) focal planes for applications in either the 3 - 5 micrometer (MWIR) or 8 - 10 micrometer (LWIR) range was recently developed by AIM. A wide variety of applications is covered by the specific features unique for these two material systems. The PtSi units provide state of the art correctability with long term stable gain and offset coefficients. The MCT units provide extremely fast frame rates like 400 Hz with snapshot integration times as short as 250 microseconds and with a thermal resolution NETD less than 20 mK for e.g. the 128 by 128 LWIR module. The unique design idea general for all of these modules is the exclusively digital interface, using 14 bit analog to digital conversion to provide state of the art correctability, access to highly dynamic scenes without any loss of information and simplified exchangeability of the units. Device specific features like bias voltages etc. are identified during the final test and stored in a memory on the driving electronics. This concept allows an easy exchange of IDCAs of the same type without any need for tuning or e.g. the possibility to upgrade a PtSi based unit to an MCT module by just loading the suitable software. Miniaturized digital signal processor (DSP) based image correction units were developed for testing and operating the units with output data rates of up to 16 Mpixels/s. These boards provide the ability for freely programmable realtime functions like two point correction and various data manipulations in thermography applications.

Physics for the Technologies. Supplementary Units.

ERIC Educational Resources Information Center

Brown, Tim; And Others

These supplemental units contain four laboratory exercises that can be used to enhance the labs in "Physics for the Technologies." The four units (one mechanical, two thermal, and one electrical) are designed to enhance labs in presenting specific concepts. Each unit can be used as an example of how the concepts behind the theory apply…

A search for space energy alternatives

NASA Technical Reports Server (NTRS)

Gilbreath, W. P.; Billman, K. W.

1978-01-01

This paper takes a look at a number of schemes for converting radiant energy in space to useful energy for man. These schemes are possible alternatives to the currently most studied solar power satellite concept. Possible primary collection and conversion devices discussed include the space particle flux devices, solar windmills, photovoltaic devices, photochemical cells, photoemissive converters, heat engines, dielectric energy conversion, electrostatic generators, plasma solar collectors, and thermionic schemes. Transmission devices reviewed include lasers and masers.

Test Results from a Direct Drive Gas Reactor Simulator Coupled to a Brayton Power Conversion Unit

NASA Technical Reports Server (NTRS)

Hervol, David S.; Briggs, Maxwell H.; Owen, Albert K.; Bragg-Sitton, Shannon M.; Godfroy, Thomas J.

2010-01-01

Component level testing of power conversion units proposed for use in fission surface power systems has typically been done using relatively simple electric heaters for thermal input. These heaters do not adequately represent the geometry or response of proposed reactors. As testing of fission surface power systems transitions from the component level to the system level it becomes necessary to more accurately replicate these reactors using reactor simulators. The Direct Drive Gas-Brayton Power Conversion Unit test activity at the NASA Glenn Research Center integrates a reactor simulator with an existing Brayton test rig. The response of the reactor simulator to a change in Brayton shaft speed is shown as well as the response of the Brayton to an insertion of reactivity, corresponding to a drum reconfiguration. The lessons learned from these tests can be used to improve the design of future reactor simulators which can be used in system level fission surface power tests.

Energy as a Natural Resource

ERIC Educational Resources Information Center

Seeger, Raymond J.

1971-01-01

Briefly discusses energy consumption per capita as an index of technical progress, a historical review of concepts related to energy conservation, energy conversion, natural sources, man-made sources, and social implications. (PR)

Magnify: A Final Technical Report of the American Energy and Manufacturing Competitiveness Partnership

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Charles

The energy landscape has undergone profound transformation, with dramatic shifts having an impact on U.S. productivity, global investment, manufacturing operations, and job creation. The sense of urgency for a tighter linkage between clean technologies, energy and advanced manufacturing has only grown. Prior to 2009, the tone of the nation’s energy conversation was centered on how to deal with long-standing energy security challenges and scarcity. Today, the tone is focused on seizing emerging energy growth opportunities to transform America’s industrial base and job creation outlook—centering on energy abundance and strength. In this context, the Council on Competitiveness and the Department ofmore » Energy’s Office of Energy Efficiency & Renewable Energy (EERE) teamed in the American Energy & Manufacturing Competitiveness (AEMC) Partnership to tackle two major goals via a multi-year partnership. The AEMC Partnership identified means to: • Increase U.S. competitiveness in the production of clean energy products • Increase U.S. manufacturing competitiveness across the board by increasing energy productivity The AEMC Partnership has engaged hundreds of leaders from industry, academia, labor and government in a series of 9 regional, progressive dialogues; original research; and 4 national summits. The AEMC dialogues and summits spanned the United States—taking place in our nation’s greatest manufacturing, research, technology and innovation hotspots. The goals of the AEMC Partnership have been straightforward: • State and define key barriers, challenges, and problems in U.S. competitiveness in manufacturing of clean energy products, energy efficiency products, and advanced manufacturing products. • Dive deeply into these problems and generate policies, solutions, concepts and models where the U.S. public and private sectors can work together to solve these problems. • Catalyze policy solutions—including models for public-private partnership (PPP) pilots—to increase competitive manufacturing of clean energy and energy efficiency products in the USA. • Elevate and increase awareness of the importance and benefits of competitive clean energy manufacturing. • Understand how energy game-changers, like breakthrough technologies, impact U.S. clean energy and energy efficient manufacturing. The Council on Competitiveness worked with its stakeholder network to generate potential PPP concepts and proposals to advance the goals of the AEMC Partnership. Magnify outlines 2 PPP concepts—honed by dialogues, conversations, interviews and research—that could be carried out by EERE and/or the Council to increase the competitive production of clean energy products, energy efficient products, and advanced manufacturing in the USA. Magnify’s 2 PPP concepts aim to bridge very specific gaps in the nation’s innovation ecosystem: • Clean Energy Materials Accelerator: This PPP concept focuses on reducing the risks associated with deploying newly developed materials in commercial products and processes by creating a platform to identify and address common challenges; increasing access to existing materials qualification and characterization tools; and creating standards for advanced materials with leaders in industry, academic, government, and other organizations. Why accelerate materials production? As the AEMC Partnership Dialogue and supporting research from the public and private sectors have documented, countries that lead in making next-generation materials will gain significant competitive advantage by unleashing a new wave of manufacturing innovation. • Manufacturing and Energy Technology Accelerator: This PPP concept is a new, physical and virtual collaborative resource platform designed to connect the nation’s world-class innovation institutions—SMEs, large multinational companies, universities, national laboratories, etc.—to facilitate the transition of cutting-edge clean energy technologies into products, processes, or services that are manufactured in the United States. Why should public and private sector leaders in innovation partner to co-create a scale-up platform? The United States is already a mecca for the world’s greatest minds in science and technology—drawn to our shores by world-class universities and opportunities to work with global leaders in innovation. Unfortunately, when it comes time to bring their ideas to market, technologists and entrepreneurs often choose, or are forced, to locate manufacturing overseas. The United States must regain its position in the world as a national scale-up platform for next-generation technologies. A thorough explanation of these PPP concepts and the rationale behind these recommendations is provided in Part 3 of Magnify. Magnify is an important step on the critical journey to define barriers, challenges and problems in the manufacturing of clean energy products and energy efficient products—and further honing concepts for scalable, public-private partnerships—to increase the competitive manufacturing of clean energy and energy efficient products, and the energy productivity throughout the U.S. manufactur¬ing sector. The rest of the world is waking up to the opportunities associated with a strategic focus on manufacturing and energy competitiveness. Global competition is on the rise, and the stakes are high for the United States to act now, to act decisively, and to leverage inherent strengths to ensure a more prosperous, competitive future for decades to come.« less

Rice by Weight, Other Produce by Bulk, and Snared Iguanas at So Much Per One. A Talk on Measurement Standards and on Metric Conversion.

ERIC Educational Resources Information Center

Allen, Harold Don

This script for a short radio broadcast on measurement standards and metric conversion begins by tracing the rise of the metric system in the international marketplace. Metric units are identified and briefly explained. Arguments for conversion to metric measures are presented. The history of the development and acceptance of the metric system is…

Space electric power design study. [laser energy conversion

NASA Technical Reports Server (NTRS)

Martini, W. R.

1976-01-01

The conversion of laser energy to electrical energy is discussed. Heat engines in which the laser heats the gas inside the engine through a window as well as heat engines in which the gas is heated by a thermal energy storage reservoir which has been heated by laser radiation are both evaluated, as well as the necessary energy storage, transmission and conversion components needed for a full system. Preliminary system concepts are presented and a recommended development program is outlined. It appears possible that a free displacer Stirling engine operating directly a linear electric generator can convert 65% of the incident laser energy into electricity.

Reformulation of the relativistic conversion between coordinate time and atomic time

NASA Technical Reports Server (NTRS)

Thomas, J. B.

1975-01-01

The relativistic conversion between coordinate time and atomic time is reformulated to allow simpler time calculations relating analysis in solar system barycentric coordinates (using coordinate time) with earth-fixed observations (measuring 'earth-bound' proper time or atomic time). After an interpretation in terms of relatively well-known concepts, this simplified formulation, which has a rate accuracy of about 10 to the minus 15th, is used to explain the conventions required in the synchronization of a worldwide clock network and to analyze two synchronization techniques - portable clocks and radio interferometry. Finally, pertinent experimental tests of relativity are briefly discussed in terms of the reformulated time conversion.

7 CFR 1794.4 - Metric units.

Code of Federal Regulations, 2014 CFR

2014-01-01

... environmental documents using non-metric equivalents with one of the following two options; metric units in parentheses immediately following the non-metric equivalents or a metric conversion table as an appendix...

7 CFR 1794.4 - Metric units.

Code of Federal Regulations, 2010 CFR

2010-01-01

... environmental documents using non-metric equivalents with one of the following two options; metric units in parentheses immediately following the non-metric equivalents or a metric conversion table as an appendix...

7 CFR 1794.4 - Metric units.

Code of Federal Regulations, 2013 CFR

2013-01-01

... environmental documents using non-metric equivalents with one of the following two options; metric units in parentheses immediately following the non-metric equivalents or a metric conversion table as an appendix...

7 CFR 1794.4 - Metric units.

Code of Federal Regulations, 2011 CFR

2011-01-01

... environmental documents using non-metric equivalents with one of the following two options; metric units in parentheses immediately following the non-metric equivalents or a metric conversion table as an appendix...

7 CFR 1794.4 - Metric units.

Code of Federal Regulations, 2012 CFR

2012-01-01

... environmental documents using non-metric equivalents with one of the following two options; metric units in parentheses immediately following the non-metric equivalents or a metric conversion table as an appendix...

Ka-band to L-band frequency down-conversion based on III-V-on-silicon photonic integrated circuits

NASA Astrophysics Data System (ADS)

Van Gasse, K.; Wang, Z.; Uvin, S.; De Deckere, B.; Mariën, J.; Thomassen, L.; Roelkens, G.

2017-12-01

In this work, we present the design, simulation and characterization of a frequency down-converter based on III-V-on-silicon photonic integrated circuit technology. We first demonstrate the concept using commercial discrete components, after which we demonstrate frequency conversion using an integrated mode-locked laser and integrated modulator. In our experiments, five channels in the Ka-band (27.5-30 GHz) with 500 MHz bandwidth are down-converted to the L-band (1.5 GHz). The breadboard demonstration shows a conversion efficiency of - 20 dB and a flat response over the 500 MHz bandwidth. The simulation of a fully integrated circuit indicates that a positive conversion gain can be obtained on a millimeter-sized photonic integrated circuit.

Harnessing surface plasmons for solar energy conversion

NASA Technical Reports Server (NTRS)

Anderson, L. M.

1983-01-01

NASA research on the feasibility of solar-energy conversion using surface plasmons is reviewed, with a focus on inelastic-tunnel-diode techniques for power extraction. The need for more efficient solar converters for planned space missions is indicated, and it is shown that a device with 50-percent efficiency could cost up to 40 times as much per sq cm as current Si cells and still be competitive. The parallel-processing approach using broadband carriers and tunable diodes is explained, and the physics of surface plasmons on metal surfaces is outlined. Technical problems being addressed include phase-matching sunlight to surface plasmons, minimizing ohmic losses and reradiation in energy transport, coupling into the tunnels by mode conversion, and gaining an understanding of the tunnel-diode energy-conversion process. Diagrams illustrating the design concepts are provided.

Responsive materials: A novel design for enhanced machine-augmented composites

PubMed Central

Bafekrpour, Ehsan; Molotnikov, Andrey; Weaver, James C.; Brechet, Yves; Estrin, Yuri

2014-01-01

The concept of novel responsive materials with a displacement conversion capability was further developed through the design of new machine-augmented composites (MACs). Embedded converter machines and MACs with improved geometry were designed and fabricated by multi-material 3D printing. This technique proved to be very effective in fabricating these novel composites with tuneable elastic moduli of the matrix and the embedded machines and excellent bonding between them. Substantial improvement in the displacement conversion efficiency of the new MACs over the existing ones was demonstrated. Also, the new design trebled the energy absorption of the MACs. Applications in energy absorbers as well as mechanical sensors and actuators are thus envisaged. A further type of MACs with conversion ability, viz. conversion of compressive displacements to torsional ones, was also proposed. PMID:24445490

Wired for Mathematics: A Conversation with Brian Butterworth.

ERIC Educational Resources Information Center

D'Arcangelo, Marcia

2001-01-01

Interview with neuropsychologist Brain Butterworth about what research has revealed about how the brain learns abstract concepts such as mathematics and the implications of these findings for teaching mathematics. (PKP)

The histochemical profile of the rat extensor digitorum longus muscle differentiates after birth and dedifferentiates in senescence.

PubMed

Lehnert, M; Laurer, H; Maier, B; Frank, J; Marzi, I; Steudel, W-I; Mautes, A

2007-01-01

Age dependent motor unit dedifferentiation is a key component of impaired muscle function in advanced age. Here, we tested the hypothesis that rat muscle histochemical profile during the lifespan of an individual has an age-specific pattern since comprehensive longitudinal studies of muscle differentiation after birth and dedifferentiation in advanced age are scarce. Our results show that extensor digitorum longus muscle (EDL) is comprised only of two fiber types after birth, type slow-oxidative (SO) and type SDH-intermediate (SDH-INT), the latter being indicative for the presence of polyneuronal innervation. In contrast to the constantly growing cross-sectional area of the muscle fibers, a dramatic decrease in SDH-INT proportion occurs between day 14 and 21 after birth resulting in a complete loss of fiber type SDH-INT at the age of 90 days (p<0.05). At the age of 270 days, the fiber type composition of rat EDL dedifferentiates as shown by the reappearance of the SDH-INT type with a further increase at the age of 540 days (p<0.05). These changes in histochemical fiber type spectra are brought about by fiber type conversion within the fast twich fibers. The findings of the present study provide further evidence that fiber type conversion is a basic mechanism leading to motor unit differentiation and dedifferentiation during ontogenesis. Fiber type conversion shows a distinct time specific pattern and is also characteristic for motor unit regeneration after peripheral nerve repair. Factors that influence fiber type conversion and thereby motor unit organization may provide a future therapeutic option to enhance the regenerative capacity of motor units.

Tunable molten oxide pool assisted plasma-melter vitrification systems

DOEpatents

Titus, Charles H.; Cohn, Daniel R.; Surma, Jeffrey E.

1998-01-01

The present invention provides tunable waste conversion systems and apparatus which have the advantage of highly robust operation and which provide complete or substantially complete conversion of a wide range of waste streams into useful gas and a stable, nonleachable solid product at a single location with greatly reduced air pollution to meet air quality standards. The systems provide the capability for highly efficient conversion of waste into high quality combustible gas and for high efficiency conversion of the gas into electricity by utilizing a high efficiency gas turbine or an internal combustion engine. The solid product can be suitable for various commercial applications. Alternatively, the solid product stream, which is a safe, stable material, may be disposed of without special considerations as hazardous material. In the preferred embodiment, the arc plasma furnace and joule heated melter are formed as a fully integrated unit with a common melt pool having circuit arrangements for the simultaneous independently controllable operation of both the arc plasma and the joule heated portions of the unit without interference with one another. The preferred configuration of this embodiment of the invention utilizes two arc plasma electrodes with an elongated chamber for the molten pool such that the molten pool is capable of providing conducting paths between electrodes. The apparatus may additionally be employed with reduced use or without further use of the gases generated by the conversion process. The apparatus may be employed as a net energy or net electricity producing unit where use of an auxiliary fuel provides the required level of electricity production. Methods and apparatus for converting metals, non-glass forming waste streams and low-ash producing inorganics into a useful gas are also provided. The methods and apparatus for such conversion include the use of a molten oxide pool having predetermined electrical, thermal and physical characteristics capable of maintaining optimal joule heating and glass forming properties during the conversion process.

Leading Deep Conversations in Collaborative Inquiry Groups

ERIC Educational Resources Information Center

Nelson, Tamara Holmlund; Deuel, Angie; Slavit, David; Kennedy, Anne

2010-01-01

Collaborative inquiry groups, such as professional learning communities and lesson study groups, are proliferating in schools across the United States. In whatever form, the potential for impacting student learning through this collaborative work is expanded or limited by the nature of teachers' conversations. Polite, congenial conversations…

Interobserver Agreement on First-Stage Conversation Analytic Transcription

ERIC Educational Resources Information Center

Roberts, Felicia; Robinson, Jeffrey D.

2004-01-01

This investigation assesses interobserver agreement on conversation analytic (CA) transcription. Four professional CA transcribers spent a maximum of 3 hours transcribing 2.5 minutes of a previously unknown, naturally occurring, mundane telephone call. Researchers unitized transcripts into words, sounds, silences, inbreaths, outbreaths, and laugh…

Technology needs for high-speed rotorcraft

NASA Technical Reports Server (NTRS)

Rutherford, John; Orourke, Matthew; Martin, Christopher; Lovenguth, Marc; Mitchell, Clark

1991-01-01

A study to determine the technology development required for high-speed rotorcraft development was conducted. The study begins with an initial assessment of six concepts capable of flight at, or greater than 450 knots with helicopter-like hover efficiency (disk loading less than 50 pfs). These concepts were sized and evaluated based on measures of effectiveness and operational considerations. Additionally, an initial assessment of the impact of technology advances on the vehicles attributes was made. From these initial concepts a tilt wing and rotor/wing concepts were selected for further evaluation. A more detailed examination of conversion and technology trade studies were conducted on these two vehicles, each sized for a different mission.

Integrated engine-generator concept for aircraft electric secondary power

NASA Technical Reports Server (NTRS)

Secunde, R. R.; Macosko, R. P.; Repas, D. S.

1972-01-01

The integrated engine-generator concept of locating an electric generator inside an aircraft turbojet or turbofan engine concentric with, and driven by, one of the main engine shafts is discussed. When properly rated, the generator can serve as an engine starter as well as a generator of electric power. The electric power conversion equipment and generator controls are conveniently located in the aircraft. Preliminary layouts of generators in a large engine together with their physical sizes and weights indicate that this concept is a technically feasible approach to aircraft secondary power.

Proceedings of the European ISTVS Conference (6th), OVK Symposium (4th), on "Off Road Vehicles in Theory and Practice". Held at Vienna, Austria on 28-30 September 1994. Volume 2.

DTIC Science & Technology

1994-09-30

experimental proof-of-concept series hybrid thermo-mechano-elec- tromechanical and/or electromechanical All-Wheel-Driven (AWD) pro- pulsion, All-Wheel...caterpillar-tracks’ motorized sprocket-, road- and tensioner- wheels form a complete proof-of-concept series hybrid thermo- mechano-electromechanical and/or...tromechanical AWA supension spheres and skid-steering conversion spheres used as integral spheres together with future new concept hybrid thermo

Ultra Wideband Polarization-Selective Conversions of Electromagnetic Waves by Metasurface under Large-Range Incident Angles.

PubMed

Yin, Jia Yuan; Wan, Xiang; Zhang, Qian; Cui, Tie Jun

2015-07-23

We propose an ultra-wideband polarization-conversion metasurface with polarization selective and incident-angle insensitive characteristics using anchor-shaped units through multiple resonances. The broadband characteristic is optimized by the genetic optimization algorithm, from which the anchor-shaped unit cell generates five resonances, resulting in expansion of the operating frequency range. Owing to the structural feature of the proposed metasurface, only x- and y-polarized incident waves can reach high-efficiency polarization conversions, realizing the polarization-selective property. The proposed metasurface is also insensitive to the angle of incident waves, which indicates a promising future in modern communication systems. We fabricate and measure the proposed metasurface, and both the simulated and measured results show ultra-wide bandwidth for the x- and y-polarized incident waves.

Ultra Wideband Polarization-Selective Conversions of Electromagnetic Waves by Metasurface under Large-Range Incident Angles

PubMed Central

Yin, Jia Yuan; Wan, Xiang; Zhang, Qian; Cui, Tie Jun

2015-01-01

We propose an ultra-wideband polarization-conversion metasurface with polarization selective and incident-angle insensitive characteristics using anchor-shaped units through multiple resonances. The broadband characteristic is optimized by the genetic optimization algorithm, from which the anchor-shaped unit cell generates five resonances, resulting in expansion of the operating frequency range. Owing to the structural feature of the proposed metasurface, only x- and y-polarized incident waves can reach high-efficiency polarization conversions, realizing the polarization-selective property. The proposed metasurface is also insensitive to the angle of incident waves, which indicates a promising future in modern communication systems. We fabricate and measure the proposed metasurface, and both the simulated and measured results show ultra-wide bandwidth for the x- and y-polarized incident waves. PMID:26202495

Kinetic concepts of thermally stimulated reactions in solids

NASA Astrophysics Data System (ADS)

Vyazovkin, Sergey

Historical analysis suggests that the basic kinetic concepts of reactions in solids were inherited from homogeneous kinetics. These concepts rest upon the assumption of a single-step reaction that disagrees with the multiple-step nature of solid-state processes. The inadequate concepts inspire such unjustified anticipations of kinetic analysis as evaluating constant activation energy and/or deriving a single-step reaction mechanism for the overall process. A more adequate concept is that of the effective activation energy, which may vary with temperature and extent of conversion. The adequacy of this concept is illustrated by literature data as well as by experimental data on the thermal dehydration of calcium oxalate monohydrate and thermal decomposition of calcium carbonate, ammonium nitrate and 1,3,5,7- tetranitro-1,3,5,7-tetrazocine.

Direct conversion of nuclear radiation energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miley, George H.

1970-01-01

This book presents a comprehensive study of methods for converting nuclear radiationi directly without resorting to a heat cycle. The concepts discussed primarily involve direct collection of charged particles released by radioisotopes and by nuclear and thermonuclear reactors. Areas considered include basic energy conversion, charged-particle transport theory, secondary-electron emission, and leakage currents and associated problems. Applications to both nuclear instrumentaion and power sources are discussed. Problems are also included as an aid to the reader or for classroom use.

Radioisotope powered alkali metal thermoelectric converter design for space systems

NASA Technical Reports Server (NTRS)

Sievers, R. K.; Bankston, C. P.

1988-01-01

The design concept of an alkali-metal thermoelectric converter (AMTEC) for 15-30-percent-efficient conversion of heat from the General Purpose (radioisotope) Heat Source (GPHS) on spacecraft is presented. The basic physical principles of the conversion cycle are outlined; a theoretical model is derived; a modular design is described and illustrated with drawings; and the overall AMTEC/GPHS system design is characterized. Predicted performance data are presented in extensive tables and graphs and discussed in detail.

Research status of wave energy conversion (WEC) device of raft structure

NASA Astrophysics Data System (ADS)

Dong, Jianguo; Gao, Jingwei; Tao, Liang; Zheng, Peng

2017-10-01

This paper has briefly described the concept of wave energy generation and six typical conversion devices. As for raft structure, detailed analysis is provided from its development process to typical devices. Taking the design process and working principle of Plamis as an example, the general principle of raft structure is briefly described. After that, a variety of raft structure models are introduced. Finally, the advantages and disadvantages, and development trend of raft structure are pointed out.

Power-Conversion Concept Designed for the Jupiter Icy Moons Orbiter

NASA Technical Reports Server (NTRS)

Mason, Lee S.

2004-01-01

The Jupiter Icy Moons Orbiter (JIMO) is a bold new mission being developed by NASA's Office of Space Science under Project Prometheus. JIMO is examining the potential of nuclear electric propulsion (NEP) technology to efficiently deliver scientific payloads to three of Jupiter's moons: Callisto, Ganymede, and Europa. A critical element of the NEP spacecraft is the space reactor power system (SRPS), consisting of the nuclear reactor, power conversion, heat rejection, and power management and distribution (PMAD).

Conversion of Sleeve Gastrectomy to Roux-en-Y Gastric Bypass is Effective for Gastro-Oesophageal Reflux Disease but not for Further Weight Loss.

PubMed

Parmar, Chetan D; Mahawar, Kamal K; Boyle, Maureen; Schroeder, Norbert; Balupuri, Shlok; Small, Peter K

2017-07-01

Inadequate weight loss (IWL)/weight regain (WR) and gastro-esophageal reflux disease (GERD), unresponsive to medical management, are two most common indications for conversion of sleeve gastrectomy (SG) to Roux-en-Y gastric bypass (RYGB). This study reports detailed outcomes of conversion of SG to RYGB for these two indications separately. We interrogated our prospectively maintained database to identify patients who underwent a conversion of their SG to RYGB in our unit. Outcomes in patients converted for IWL/WR and those converted for GERD were evaluated separately. We carried out 22 SG to RYGB in our unit between Aug 2012 and April 2015 with a mean follow-up of 16 months. Indication for conversion was GERD in 10/22 (45.5%) patients and IWL/WR in 11/22 (50.0%) patients. Patients undergoing conversion for GERD were significantly lighter (BMI 30.5) than those converted for IWL/WR (BMI 43.3) at the time of conversion. The conversion was very effective for GERD with 100% patients reporting improvement in symptoms, and 80% patients were able to stop their antacid medications. IWL/WR group achieved a further BMI drop of 2.5 points 2 years after surgery (final BMI 40.8) in comparison with 2.0 points BMI drop achieved by the GERD group (final BMI 28.5). This study demonstrates that conversion of SG to RYGB is effective for GERD symptoms but not for further weight loss, which was modest in both groups. Future studies need to examine the best revisional procedure for IWL/WR after SG.

Socio-phenomenology and conversation analysis: interpreting video lifeworld healthcare interactions.

PubMed

Bickerton, Jane; Procter, Sue; Johnson, Barbara; Medina, Angel

2011-10-01

This article uses a socio-phenomenological methodology to develop knowledge and understanding of the healthcare consultation based on the concept of the lifeworld. It concentrates its attention on social action rather than strategic action and a systems approach. This article argues that patient-centred care is more effective when it is informed through a lifeworld conception of human mutual shared interaction. Videos offer an opportunity for a wide audience to experience the many kinds of conversations and dynamics that take place in consultations. Visual sociology used in this article provides a method to organize video emotional, knowledge and action conversations as well as dynamic typical consultation situations. These interactions are experienced through the video materials themselves unlike conversation analysis where video materials are first transcribed and then analysed. Both approaches have the potential to support intersubjective learning but this article argues that a video lifeworld schema is more accessible to health professionals and the general public. The typical interaction situations are constructed through the analysis of video materials of consultations in a London walk-in centre. Further studies are planned in the future to extend and replicate results in other healthcare services. This method of analysis focuses on the ways in which the everyday lifeworld informs face-to-face person-centred health care and supports social action as a significant factor underpinning strategic action and a systems approach to consultation practice. © 2011 Blackwell Publishing Ltd.

SI (Metric) handbook

NASA Technical Reports Server (NTRS)

Artusa, Elisa A.

1994-01-01

This guide provides information for an understanding of SI units, symbols, and prefixes; style and usage in documentation in both the US and in the international business community; conversion techniques; limits, fits, and tolerance data; and drawing and technical writing guidelines. Also provided is information of SI usage for specialized applications like data processing and computer programming, science, engineering, and construction. Related information in the appendixes include legislative documents, historical and biographical data, a list of metric documentation, rules for determining significant digits and rounding, conversion factors, shorthand notation, and a unit index.

A Botany Unit: Seed Plants.

ERIC Educational Resources Information Center

Smythe, Cathy

1983-01-01

Presents a botany unit designed to provide understanding of a plant life cycle, plant parts and functions, and variety within the plant world. The unit is organized according to plant morphology (structure). Each section includes concepts fostered, suggestions for focused discussions, experiments, and activities to support concept development.…

V/STOL concepts in the United States: Past, present, and future

NASA Technical Reports Server (NTRS)

Nelms, W. P.; Anderson, S. B.

1984-01-01

Nonhelicopter types of V/STOL aircraft developed in the United States are reviewed, and some lessons learned from a selected number of concepts are highlighted. The AV-8B, which was developed by modifications to the British Harrier is the only current concept examined. Configurations proposed for the future subsonic, multimissing aircraft and the future supersonic fighter/attack aircraft are described. Emphasis is on these supersonic concepts.

Mineralogical conversion of asbestos containing materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsford, S.K.; Foltz, A.D.; Ek, R.B.

The principal objective of the Technical Task Plan (TTP) is to demonstrate a thermal-chemical mineralogical asbestos conversion unit at the Hanford Site, which converts non-radiological asbestos containing materials (ACMs) into an asbestos-free material. The permanent thermal-chemical mineralogical conversion of ACMs to a non-toxic, non-hazardous, potentially marketable end product should not only significantly reduce the waste stream volumes but terminate the {open_quotes}cradle to grave{close_quotes} ownership liabilities.

Urban 5th Graders Conceptions during a Place-Based Inquiry Unit on Watersheds

ERIC Educational Resources Information Center

Endreny, Anna Henderson

2010-01-01

This study aimed to determine how 33 urban 5th grade students' science conceptions changed during a place-based inquiry unit on watersheds. Research on watershed and place-based education was used as a framework to guide the teaching of the unit as well as the research study. A teacher-researcher designed the curriculum, taught the unit and…

Toward a Nation-Building Operating Concept

DTIC Science & Technology

2010-04-13

of United Nations intervention in Timor, argues that an interim protectorate is useful only if implemented by a multi -national coalition. However...to a franchise agreement or venture capital investment. The United States provides capital and expertise to indigenous group predicated on agreed...Toward a Nation-Building Operating Concept by Colonel John DeJarnette United States Army School of Advanced Military Studies United States

Solar thermal electricity generation

NASA Astrophysics Data System (ADS)

Gasemagha, Khairy Ramadan

1993-01-01

This report presents the results of modeling the thermal performance and economic feasibility of large (utility scale) and small solar thermal power plants for electricity generation. A number of solar concepts for power systems applications have been investigated. Each concept has been analyzed over a range of plant power ratings from 1 MW(sub e) to 300 MW(sub e) and over a range of capacity factors from a no-storage case (capacity factor of about 0.25 to 0.30) up to intermediate load capacity factors in the range of 0.46 to 0.60. The solar plant's economic viability is investigated by examining the effect of various parameters on the plant costs (both capital and O & M) and the levelized energy costs (LEC). The cost components are reported in six categories: collectors, energy transport, energy storage, energy conversion, balance of plant, and indirect/contingency costs. Concentrator and receiver costs are included in the collector category. Thermal and electric energy transport costs are included in the energy transport category. Costs for the thermal or electric storage are included in the energy storage category; energy conversion costs are included in the energy conversion category. The balance of plant cost category comprises the structures, land, service facilities, power conditioning, instrumentation and controls, and spare part costs. The indirect/contingency category consists of the indirect construction and the contingency costs. The concepts included in the study are (1) molten salt cavity central receiver with salt storage (PFCR/R-C-Salt); (2) molten salt external central receiver with salt storage (PFCR/R-E-Salt); (3) sodium external central receiver with sodium storage (PFCR/RE-Na); (4) sodium external central receiver with salt storage (PFCR/R-E-Na/Salt); (5) water/steam external central receiver with oil/rock storage (PFCR/R-E-W/S); (6) parabolic dish with stirling engine conversion and lead acid battery storage (PFDR/SLAB); (7) parabolic dish with stirling engine conversion and redox advanced battery storage (PFDR/S-RAB); and (8) parabolic trough with oil/rock storage (LFDR/R-HT-45). Key annual efficiency and economic results of the study are highlighted in tabular format for plant sizes and capacity factor that resulted in the lowest LEC over the analysis range.

Novel chip coating approaches to improve white LED technology

NASA Astrophysics Data System (ADS)

Hartmann, Paul; Schweighart, Marko; Sommer, Christian; Wenzl, Franz-P.; Zinterl, Ernst; Hoschopf, Hans; Pachler, Peter; Tasch, Stefan

2008-02-01

Key market requirements for white LEDs, especially in the general lighting and automotive headlamp segments call for improved concepts and performance of white LEDs based on phosphor conversion. Major challenges are small emission areas, highest possible intensities, long-term color stability, and spatial homogeneity of color coordinates. On the other hand, the increasingly high radiation power of the blue LEDs poses problems for all involved materials. Various thick film coating technologies are widely used for applying the color conversion layer to the semiconductor chip. We present novel concepts based on Silicate phosphors with high performance in terms of spatial homogeneity of the emission and variability of the color temperature. Numerical calculation of the optical properties with the help of state-of-the-art simulation tools was used as a basis for the practical optimization of the layer geometries.

Energy and momentum management of the Space Station using magnetically suspended composite rotors

NASA Technical Reports Server (NTRS)

Eisenhaure, D. B.; Oglevie, R. E.; Keckler, C. R.

1985-01-01

The research addresses the feasibility of using magnetically suspended composite rotors to jointly perform the energy and momentum management functions of an advanced manned Space Station. Recent advancements in composite materials, magnetic suspensions, and power conversion electronics have given flywheel concepts the potential to simultaneously perform these functions for large, long duration spacecraft, while offering significant weight, volume, and cost savings over conventional approaches. The Space Station flywheel concept arising out of this study consists of a composite-material rotor, a large-angle magnetic suspension (LAMS) system, an ironless armature motor/generator, and high-efficiency power conversion electronics. The LAMS design permits the application of appropriate spacecraft control torques without the use of conventional mechanical gimbals. In addition, flywheel systems have the growth potential and modularity needed to play a key role in many future system developments.

Teaching about Judicial Review. ERIC Digest.

ERIC Educational Resources Information Center

Patrick, John J.

Judicial review is a fundamental facet of constitutional government in the United States. Invented during the founding of the United States, judicial review has spread to most constitutional democracies of the world. This digest discusses: (1) the concept of judicial review; (2) the origin of this concept; (3) the uses of this concept in U.S.…

The Babushka Concept--An Instructional Sequence to Enhance Laboratory Learning in Science Education

ERIC Educational Resources Information Center

Gårdebjer, Sofie; Larsson, Anette; Adawi, Tom

2017-01-01

This paper deals with a novel method for improving the traditional "verification" laboratory in science education. Drawing on the idea of integrated instructional units, we describe an instructional sequence which we call the Babushka concept. This concept consists of three integrated instructional units: a start-up lecture, a laboratory…

Outline of Basic Concepts in Anthropology. Publication No. 1.

ERIC Educational Resources Information Center

Georgia Univ., Athens. Anthropology Curriculum Project.

This teaching aid outlines basic anthropological concepts described in the various units of the Anthropology Curriculum Project. The outline of important concepts to be learned is intended to be used by the teacher in conjunction with the other instructional materials in each unit. The introduction defines anthropology, its branches and purposes.…

Design and Testing of a Flexible Inclinometer Probe for Model Tests of Landslide Deep Displacement Measurement.

PubMed

Zhang, Yongquan; Tang, Huiming; Li, Changdong; Lu, Guiying; Cai, Yi; Zhang, Junrong; Tan, Fulin

2018-01-14

The physical model test of landslides is important for studying landslide structural damage, and parameter measurement is key in this process. To meet the measurement requirements for deep displacement in landslide physical models, an automatic flexible inclinometer probe with good coupling and large deformation capacity was designed. The flexible inclinometer probe consists of several gravity acceleration sensing units that are protected and positioned by silicon encapsulation, all the units are connected to a 485-comunication bus. By sensing the two-axis tilt angle, the direction and magnitude of the displacement for a measurement unit can be calculated, then the overall displacement is accumulated according to all units, integrated from bottom to top in turn. In the conversion from angle to displacement, two spline interpolation methods are introduced to correct and resample the data; one is to interpolate the displacement after conversion, and the other is to interpolate the angle before conversion; compared with the result read from checkered paper, the latter is proved to have a better effect, with an additional condition that the displacement curve move up half the length of the unit. The flexible inclinometer is verified with respect to its principle and arrangement by a laboratory physical model test, and the test results are highly consistent with the actual deformation of the landslide model.

Design and Testing of a Flexible Inclinometer Probe for Model Tests of Landslide Deep Displacement Measurement

PubMed Central

Zhang, Yongquan; Tang, Huiming; Li, Changdong; Lu, Guiying; Cai, Yi; Zhang, Junrong; Tan, Fulin

2018-01-01

The physical model test of landslides is important for studying landslide structural damage, and parameter measurement is key in this process. To meet the measurement requirements for deep displacement in landslide physical models, an automatic flexible inclinometer probe with good coupling and large deformation capacity was designed. The flexible inclinometer probe consists of several gravity acceleration sensing units that are protected and positioned by silicon encapsulation, all the units are connected to a 485-comunication bus. By sensing the two-axis tilt angle, the direction and magnitude of the displacement for a measurement unit can be calculated, then the overall displacement is accumulated according to all units, integrated from bottom to top in turn. In the conversion from angle to displacement, two spline interpolation methods are introduced to correct and resample the data; one is to interpolate the displacement after conversion, and the other is to interpolate the angle before conversion; compared with the result read from checkered paper, the latter is proved to have a better effect, with an additional condition that the displacement curve move up half the length of the unit. The flexible inclinometer is verified with respect to its principle and arrangement by a laboratory physical model test, and the test results are highly consistent with the actual deformation of the landslide model. PMID:29342902

Role of Bioreactors in Microbial Biomass and Energy Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Liang; Zhang, Biao; Zhu, Xun

Bioenergy is the world’s largest contributor to the renewable and sustainable energy sector, and it plays a significant role in various energy industries. A large amount of research has contributed to the rapidly evolving field of bioenergy and one of the most important topics is the use of the bioreactor. Bioreactors play a critical role in the successful development of technologies for microbial biomass cultivation and energy conversion. In this chapter, after a brief introduction to bioreactors (basic concepts, configurations, functions, and influencing factors), the applications of the bioreactor in microbial biomass, microbial biofuel conversion, and microbial electrochemical systems aremore » described. Importantly, the role and significance of the bioreactor in the bioenergy process are discussed to provide a better understanding of the use of bioreactors in managing microbial biomass and energy conversion.« less

Energy Conversion and Storage Requirements for Hybrid Electric Aircraft

NASA Technical Reports Server (NTRS)

Misra, Ajay

2016-01-01

Among various options for reducing greenhouse gases in future large commercial aircraft, hybrid electric option holds significant promise. In the hybrid electric aircraft concept, gas turbine engine is used in combination with an energy storage system to drive the fan that propels the aircraft, with gas turbine engine being used for certain segments of the flight cycle and energy storage system being used for other segments. The paper will provide an overview of various energy conversion and storage options for hybrid electric aircraft. Such options may include fuel cells, batteries, super capacitors, multifunctional structures with energy storage capability, thermoelectric, thermionic or a combination of any of these options. The energy conversion and storage requirements for hybrid electric aircraft will be presented. The role of materials in energy conversion and storage systems for hybrid electric aircraft will be discussed.

Streamside zone width and amphibian and reptile abundance

Treesearch

D. Craig Rudolph; James G. Dickson

1990-01-01

Many natural pine-hardwood stands in the southeastern United States are being converted to pine plantations with short rotations. This forest conversion alters vertebrate communities, particularly amphibians and reptiles (Bennett et al., 1980; Rakowitz, 1983). One practice in stand conversion to accommodate vertebrate species is the retention of strips of unharvested,...

Metrics, Lumber, and the Shop Teacher

ERIC Educational Resources Information Center

Craemer, Peter J.

1978-01-01

As producers of lumber are preparing to convert their output to the metric system, wood shop and building construction teachers must become familiar with the metric measurement language and methods. Manufacturers prefer the "soft conversion" process of changing English to metric units rather than hard conversion, or redimensioning of lumber. Some…

The Metric System--An Overview.

ERIC Educational Resources Information Center

Hovey, Larry; Hovey, Kathi

1983-01-01

Sections look at: (1) Historical Perspective; (2) Naming the New System; (3) The Metric Units; (4) Measuring Larger and Smaller Amounts; (5) Advantage of Using the Metric System; (6) Metric Symbols; (7) Conversion from Metric to Customary System; (8) General Hints for Helping Children Understand; and (9) Current Status of Metric Conversion. (MP)

Metrication: What Can HRD Specialists Do?

ERIC Educational Resources Information Center

Short, Larry G.

1978-01-01

First discusses some features of the Metric Conversion Act which established federal support of metric system usage in the United States. Then covers the following: what HRD (Human Resources Development) specialists can do to assist their company managers during the conversion process; metric training strategies; and how to prepare for metric…

Conversational English Program, 2.

ERIC Educational Resources Information Center

Instituto de Idiomas Yazigi, Sao Paulo (Brazil). Centro de Linguistica Aplicada.

This second book of a conversational English program for adults contains an introductory section in Portuguese and exercises in English. The text centers around an English-speaking family from the United States that goes to live in Brazil. It contains color photographs with captions followed by exercises. The exercises are in English and involve…

Conversational English Program, 1.

ERIC Educational Resources Information Center

Instituto de Idiomas Yazigi, Sao Paulo (Brazil). Centro de Linguistica Aplicada.

This first book of a conversational English program for adults contains an introductory section in Portuguese and exercises in English. The text centers around an English-speaking family from the United States that goes to live in Brazil. It contains color photographs with captions followed by exercises. The exercises are in English and involve…

A History of Geothermal Energy Research and Development in the United States. Energy Conversion 1976-2006

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mines, Gregory L.

2010-09-01

This report, the last in a four-part series, summarizes significant research projects performed by the U.S. Department of Energy (DOE) over 30 years to overcome challenges in energy conversion and to make generation of electricity from geothermal resources more cost-competitive.

Feasibility Analysis of Liquefying Oxygen Generated from Water Electrolysis Units on Lunar Surface

NASA Technical Reports Server (NTRS)

Jeng, Frank F.

2009-01-01

Concepts for liquefying oxygen (O2) generated from water electrolysis subsystems on the Lunar surface were explored. Concepts for O2 liquefaction units capable of generating 1.38 lb/hr (0.63 kg/hr) liquid oxygen (LOX) were developed. Heat and mass balance calculations for the liquefaction concepts were conducted. Stream properties, duties of radiators, heat exchangers and compressors for the selected concepts were calculated and compared.

Preliminary assessment of rover power systems for the Mars Rover Sample Return Mission

NASA Technical Reports Server (NTRS)

Bents, David J.

1989-01-01

Four isotope power system concepts were presented and compared on a common basis for application to on-board electrical prime power for an autonomous planetary rover vehicle. A representative design point corresponding to the Mars Rover Sample Return (MRSR) preliminary mission requirements (500 W) was selected for comparison purposes. All systems concepts utilize the General Purpose Heat Source (GPHS) isotope heat source developed by DOE. Two of the concepts employ thermoelectric (TE) conversion: one using the GPHS Radioisotope Thermoelectric Generator (RTG) used as a reference case, the other using an advanced RTG with improved thermoelectric materials. The other two concepts employed are dynamic isotope power systems (DIPS): one using a closed Brayton cycle (CBC) turboalternator, and the other using a free piston Stirling cycle engine/linear alternator (FPSE) with integrated heat source/heater head. Near term technology levels have been assumed for concept characterization using component technology figure-of-merit values taken from the published literature. For example, the CBC characterization draws from the historical test database accumulated from space Brayton cycle subsystems and components from the NASA B engine through the mini-Brayton rotating unit. TE system performance is estimated from Voyager/multihundred Watt (MHW)-RTG flight experience through Mod-RTG performance estimates considering recent advances in TE materials under the DOD/DOE/NASA SP-100 and NASA Committee on Scientific and Technological Information programs. The Stirling DIPS system is characterized from scaled-down Space Power Demonstrator Engine (SPDE) data using the GPHS directly incorporated into the heater head. The characterization/comparison results presented here differ from previous comparison of isotope power (made for Low Earth Orbit (LEO) applications) because of the elevated background temperature on the Martian surface compared to LEO, and the higher sensitivity of dynamic systems to elevated sink temperature. The mass advantage of dynamic systems is significantly reduced for this application due to Mars' elevated background temperature.

Comparing Approaches to Converting Large High Schools into Smaller Units

ERIC Educational Resources Information Center

Levine, Thomas H

2011-01-01

Scholars and reformers in the United States have called for converting large high schools into smaller units to provide a more effective, personal, and culturally responsive education for all students. Current literature argues that such "conversion high schools" should break into fully autonomous small schools rather than more…

Diversions

ERIC Educational Resources Information Center

Gough, John

2017-01-01

Australia has used SI metric units for measurement for decades now, although the conversion of measurements from the earlier Imperial units--known as metrication--commenced subsequently in 1971, and was not completed until 1988. All Primary and Secondary schools were using only metric units in school lessons by 1973, and it became illegal to teach…

SPOKEN COCHABAMBA QUECHUA, UNITS 13-24.

ERIC Educational Resources Information Center

LASTRA, YOLANDA; SOLA, DONALD F.

UNITS 13-24 OF THE SPOKEN COCHABAMBA QUECHUA COURSE FOLLOW THE GENERAL FORMAT OF THE FIRST VOLUME (UNITS 1-12). THIS SECOND VOLUME IS INTENDED FOR USE IN AN INTERMEDIATE OR ADVANCED COURSE AND INCLUDES MORE COMPLEX DIALOGS, CONVERSATIONS, "LISTENING-INS," AND DICTATIONS, AS WELL AS GRAMMAR AND EXERCISE SECTIONS COVERING ADDITIONAL…

NOMINAL VALUES FOR SELECTED SOLAR AND PLANETARY QUANTITIES: IAU 2015 RESOLUTION B3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prša, Andrej; Harmanec, Petr; Torres, Guillermo

In this brief communication we provide the rationale for and the outcome of the International Astronomical Union (IAU) resolution vote at the XXIXth General Assembly in Honolulu, Hawaii, in 2015, on recommended nominal conversion constants for selected solar and planetary properties. The problem addressed by the resolution is a lack of established conversion constants between solar and planetary values and SI units: a missing standard has caused a proliferation of solar values (e.g., solar radius, solar irradiance, solar luminosity, solar effective temperature, and solar mass parameter) in the literature, with cited solar values typically based on best estimates at the timemore » of paper writing. As precision of observations increases, a set of consistent values becomes increasingly important. To address this, an IAU Working Group on Nominal Units for Stellar and Planetary Astronomy formed in 2011, uniting experts from the solar, stellar, planetary, exoplanetary, and fundamental astronomy, as well as from general standards fields to converge on optimal values for nominal conversion constants. The effort resulted in the IAU 2015 Resolution B3, passed at the IAU General Assembly by a large majority. The resolution recommends the use of nominal solar and planetary values, which are by definition exact and are expressed in SI units. These nominal values should be understood as conversion factors only, not as the true solar/planetary properties or current best estimates. Authors and journal editors are urged to join in using the standard values set forth by this resolution in future work and publications to help minimize further confusion.« less

Recombination-dependent replication and gene conversion homogenize repeat sequences and diversify plastid genome structure.

PubMed

Ruhlman, Tracey A; Zhang, Jin; Blazier, John C; Sabir, Jamal S M; Jansen, Robert K

2017-04-01

There is a misinterpretation in the literature regarding the variable orientation of the small single copy region of plastid genomes (plastomes). The common phenomenon of small and large single copy inversion, hypothesized to occur through intramolecular recombination between inverted repeats (IR) in a circular, single unit-genome, in fact, more likely occurs through recombination-dependent replication (RDR) of linear plastome templates. If RDR can be primed through both intra- and intermolecular recombination, then this mechanism could not only create inversion isomers of so-called single copy regions, but also an array of alternative sequence arrangements. We used Illumina paired-end and PacBio single-molecule real-time (SMRT) sequences to characterize repeat structure in the plastome of Monsonia emarginata (Geraniaceae). We used OrgConv and inspected nucleotide alignments to infer ancestral nucleotides and identify gene conversion among repeats and mapped long (>1 kb) SMRT reads against the unit-genome assembly to identify alternative sequence arrangements. Although M. emarginata lacks the canonical IR, we found that large repeats (>1 kilobase; kb) represent ∼22% of the plastome nucleotide content. Among the largest repeats (>2 kb), we identified GC-biased gene conversion and mapping filtered, long SMRT reads to the M. emarginata unit-genome assembly revealed alternative, substoichiometric sequence arrangements. We offer a model based on RDR and gene conversion between long repeated sequences in the M. emarginata plastome and provide support that both intra-and intermolecular recombination between large repeats, particularly in repeat-rich plastomes, varies unit-genome structure while homogenizing the nucleotide sequence of repeats. © 2017 Botanical Society of America.

Nominal Values for Selected Solar and Planetary Quantities: IAU 2015 Resolution B3

NASA Astrophysics Data System (ADS)

Prša, Andrej; Harmanec, Petr; Torres, Guillermo; Mamajek, Eric; Asplund, Martin; Capitaine, Nicole; Christensen-Dalsgaard, Jørgen; Depagne, Éric; Haberreiter, Margit; Hekker, Saskia; Hilton, James; Kopp, Greg; Kostov, Veselin; Kurtz, Donald W.; Laskar, Jacques; Mason, Brian D.; Milone, Eugene F.; Montgomery, Michele; Richards, Mercedes; Schmutz, Werner; Schou, Jesper; Stewart, Susan G.

2016-08-01

In this brief communication we provide the rationale for and the outcome of the International Astronomical Union (IAU) resolution vote at the XXIXth General Assembly in Honolulu, Hawaii, in 2015, on recommended nominal conversion constants for selected solar and planetary properties. The problem addressed by the resolution is a lack of established conversion constants between solar and planetary values and SI units: a missing standard has caused a proliferation of solar values (e.g., solar radius, solar irradiance, solar luminosity, solar effective temperature, and solar mass parameter) in the literature, with cited solar values typically based on best estimates at the time of paper writing. As precision of observations increases, a set of consistent values becomes increasingly important. To address this, an IAU Working Group on Nominal Units for Stellar and Planetary Astronomy formed in 2011, uniting experts from the solar, stellar, planetary, exoplanetary, and fundamental astronomy, as well as from general standards fields to converge on optimal values for nominal conversion constants. The effort resulted in the IAU 2015 Resolution B3, passed at the IAU General Assembly by a large majority. The resolution recommends the use of nominal solar and planetary values, which are by definition exact and are expressed in SI units. These nominal values should be understood as conversion factors only, not as the true solar/planetary properties or current best estimates. Authors and journal editors are urged to join in using the standard values set forth by this resolution in future work and publications to help minimize further confusion.

Introduction to wind energy systems

NASA Astrophysics Data System (ADS)

Wagner, H.-J.

2017-07-01

This article presents the basic concepts of wind energy and deals with the physics and mechanics of operation. It describes the conversion of wind energy into rotation of turbine, and the critical parameters governing the efficiency of this conversion. After that it presents an overview of various parts and components of windmills. The connection to the electrical grid, the world status of wind energy use for electricity production, the cost situation and research and development needs are further aspects which will be considered.

Introduction to wind energy systems

NASA Astrophysics Data System (ADS)

Wagner, H.-J.

2015-08-01

This article presents the basic concepts of wind energy and deals with the physics and mechanics of operation. It describes the conversion of wind energy into rotation of turbine, and the critical parameters governing the efficiency of this conversion. After that it presents an overview of various parts and components of windmills. The connection to the electrical grid, the world status of wind energy use for electricity production, the cost situation and research and development needs are further aspects which will be considered.

Static and dynamic high power, space nuclear electric generating systems

NASA Technical Reports Server (NTRS)

Wetch, J. R.; Begg, L. L.; Koester, J. K.

1985-01-01

Space nuclear electric generating systems concepts have been assessed for their potential in satisfying future spacecraft high power (several megawatt) requirements. Conceptual designs have been prepared for reactor power systems using the most promising static (thermionic) and the most promising dynamic conversion processes. Component and system layouts, along with system mass and envelope requirements have been made. Key development problems have been identified and the impact of the conversion process selection upon thermal management and upon system and vehicle configuration is addressed.

Synthesis of ceramic-based porous gradient structures for applications in energy conversion and related fields

NASA Astrophysics Data System (ADS)

Graule, Thomas; Ozog, Paulina; Durif, Caroline; Wilkens-Heinecke, Judit; Kata, Dariusz

2016-06-01

Porous, graded ceramic structures are of high relevance in the field of energy conversion as well as in catalysis, and additionally in filtration technology and in biomedical applications. Among different technologies for the tailored design for such structures we demonstrate here a new environmental friendly UV curing-based concept to prepare laminated structures with pore sizes ranging from a few microns up to 50 microns in diameter and with porosities ranging from 10% up to 75 vol.% porosity.

Visual unit analysis: a descriptive approach to landscape assessment

Treesearch

R. J. Tetlow; S. R. J. Sheppard

1979-01-01

Analysis of the visible attributes of landscapes is an important component of the planning process. When landscapes are at regional scale, economical and effective methodologies are critical. The Visual Unit concept appears to offer a logical and useful framework for description and evaluation. The concept subdivides landscape into coherent, spatially-defined units....

POSITION AND MOTION, A SCIENCE UNIT FOR THE UPPER ELEMENTARY GRADES, STUDENT MANUAL.

ERIC Educational Resources Information Center

BERGER, CARL; MONTGOMERY, MARSHALL

THIS MANUAL IS DESIGNED FOR STUDENTS IN UPPER ELEMENTARY GRADES STUDYING THE SCIENCE CURRICULUM IMPROVEMENT STUDY (SCIS) UNIT "POSITION AND MOTION". THE OVERALL STRUCTURE OF THE UNIT FOLLOWS A CYCLE OF PRELIMINARY EXPLORATION, INVENTION OF SPECIFIC CONCEPTS RELATED TO REFERENCE FRAMES, AND DISCOVERY OF THE USEFULNESS OF THE CONCEPT.…

Optimized energy harvesting from mechanical vibrations through piezoelectric actuators, based on a synchronized switching technique

NASA Astrophysics Data System (ADS)

Tsampas, P.; Roditis, G.; Papadimitriou, V.; Chatzakos, P.; Gan, Tat-Hean

2013-05-01

Increasing demand in mobile, autonomous devices has made energy harvesting a particular point of interest. Systems that can be powered up by a few hundreds of microwatts could feature their own energy extraction module. Energy can be harvested from the environment close to the device. Particularly, the ambient mechanical vibrations conversion via piezoelectric transducers is one of the most investigated fields for energy harvesting. A technique for optimized energy harvesting using piezoelectric actuators called "Synchronized Switching Harvesting" is explored. Comparing to a typical full bridge rectifier, the proposed harvesting technique can highly improve harvesting efficiency, even in a significantly extended frequency window around the piezoelectric actuator's resonance. In this paper, the concept of design, theoretical analysis, modeling, implementation and experimental results using CEDRAT's APA 400M-MD piezoelectric actuator are presented in detail. Moreover, we suggest design guidelines for optimum selection of the storage unit in direct relation to the characteristics of the random vibrations. From a practical aspect, the harvesting unit is based on dedicated electronics that continuously sense the charge level of the actuator's piezoelectric element. When the charge is sensed, to come to a maximum, it is directed to speedily flow into a storage unit. Special care is taken so that electronics operate at low voltages consuming a very small amount of the energy stored. The final prototype developed includes the harvesting circuit implemented with miniaturized, low cost and low consumption electronics and a storage unit consisting of a super capacitors array, forming a truly self-powered system drawing energy from ambient random vibrations of a wide range of characteristics.

Influence of Molecular Oxygen on Ortho-Para Conversion of Water Molecules

NASA Astrophysics Data System (ADS)

Valiev, R. R.; Minaev, B. F.

2017-07-01

The mechanism of influence of molecular oxygen on the probability of ortho-para conversion of water molecules and its relation to water magnetization are considered within the framework of the concept of paramagnetic spin catalysis. Matrix elements of the hyperfine ortho-para interaction via the Fermi contact mechanism are calculated, as well as the Maliken spin densities on water protons in H2O and O2 collisional complexes. The mechanism of penetration of the electron spin density into the water molecule due to partial spin transfer from paramagnetic oxygen is considered. The probability of ortho-para conversion of the water molecules is estimated by the quantum chemistry methods. The results obtained show that effective ortho-para conversion of the water molecules is possible during the existence of water-oxygen dimers. An external magnetic field affects the ortho-para conversion rate given that the wave functions of nuclear spin sublevels of the water protons are mixed in the complex with oxygen.

Anaerobic Digestion.

PubMed

Liebetrau, Jan; Sträuber, Heike; Kretzschmar, Jörg; Denysenko, Velina; Nelles, Michael

2017-04-09

The term anaerobic digestion usually refers to the microbial conversion of organic material to biogas, which mainly consists of methane and carbon dioxide. The technical application of the naturally-occurring process is used to provide a renewable energy carrier and - as the substrate is often waste material - to reduce the organic matter content of the substrate prior to disposal.Applications can be found in sewage sludge treatment, the treatment of industrial and municipal solid wastes and wastewaters (including landfill gas utilization), and the conversion of agricultural residues and energy crops.For biorefinery concepts, the anaerobic digestion (AD) process is, on the one hand, an option to treat organic residues from other production processes. Concomitant effects are the reduction of organic carbon within the treated substance, the conversion of nitrogen and sulfur components, and the production of an energy-rich gas - the biogas. On the other hand, the multistep conversion of complex organic material offers the possibility of interrupting the conversion chain and locking out intermediates for utilization as basic material within the chemical industry.

Statistics for Radiology Research.

PubMed

Obuchowski, Nancy A; Subhas, Naveen; Polster, Joshua

2017-02-01

Biostatistics is an essential component in most original research studies in imaging. In this article we discuss five key statistical concepts for study design and analyses in modern imaging research: statistical hypothesis testing, particularly focusing on noninferiority studies; imaging outcomes especially when there is no reference standard; dealing with the multiplicity problem without spending all your study power; relevance of confidence intervals in reporting and interpreting study results; and finally tools for assessing quantitative imaging biomarkers. These concepts are presented first as examples of conversations between investigator and biostatistician, and then more detailed discussions of the statistical concepts follow. Three skeletal radiology examples are used to illustrate the concepts. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

The impact of analogies on creative concept generation: lessons from an in vivo study in engineering design.

PubMed

Chan, Joel; Schunn, Christian

2015-01-01

Research on innovation often highlights analogies from sources outside the current problem domain as a major source of novel concepts; however, the mechanisms underlying this relationship are not well understood. We analyzed the temporal interplay between far analogy use and creative concept generation in a professional design team's brainstorming conversations, investigating the hypothesis that far analogies lead directly to very novel concepts via large steps in conceptual spaces (jumps). Surprisingly, we found that concepts were more similar to their preceding concepts after far analogy use compared to baseline situations (i.e., without far analogy use). Yet far analogies increased the team's concept generation rate compared to baseline conditions. Overall, these results challenge the view that far analogies primarily lead to novel concepts via jumps in conceptual spaces and suggest alternative pathways from far analogies to novel concepts (e.g., iterative, deep exploration within a functional space). Copyright © 2014 Cognitive Science Society, Inc.

NASA education briefs for the classroom. Metrics in space

NASA Technical Reports Server (NTRS)

1982-01-01

The use of metric measurement in space is summarized for classroom use. Advantages of the metric system over the English measurement system are described. Some common metric units are defined, as are special units for astronomical study. International system unit prefixes and a conversion table of metric/English units are presented. Questions and activities for the classroom are recommended.

NASA education briefs for the classroom. Metrics in space

NASA Astrophysics Data System (ADS)

The use of metric measurement in space is summarized for classroom use. Advantages of the metric system over the English measurement system are described. Some common metric units are defined, as are special units for astronomical study. International system unit prefixes and a conversion table of metric/English units are presented. Questions and activities for the classroom are recommended.

Satellite communications system 'Tyulpan'

NASA Astrophysics Data System (ADS)

Tchuyan, R. K.; Tarasov, E. V.; Belousov, A. P.; Balyk, V. M.; Kovtunenko, V. M.; Morozov, V. A.; Andreev, V. A.; v'yunenko, K. A.

1993-10-01

A concept of the satellite communication system called 'Tyulpan' (because or its tulip-resembling shape) is considered. This conception envisages the use of six satellites-retranslators installed on high-latitude elliptic orbits. Such a system can provide the communication for mean- and high-latitude region of Europe, Asia, and America. For the communication, super small ground stations of 0.4 m in diameter can be used. In the development of system conception, the already existing technical solutions and possibility of conversion or existing installations of military destination were taken into account. Therefore, the system considered can be realized at the earliest possible date.

The driving forces of land change in the Northern Piedmont of the United States

USGS Publications Warehouse

Auch, Roger F.; Napton, Darrell E.; Kambly, Steven; Moreland, Thomas R.; Sayler, Kristi L.

2012-01-01

Driving forces facilitate or inhibit land-use/land-cover change. Human driving forces include political, economic, cultural, and social attributes that often change across time and space. Remotely sensed imagery provides regional land-change data for the Northern Piedmont, an ecoregion of the United States that continued to urbanize after 1970 through conversion of agricultural and forest land covers to developed uses. Eight major driving forces facilitated most of the land conversion; other drivers inhibited or slowed change. A synergistic web of drivers may be more important in understanding land change than individual drivers by themselves.

Improving Health Care Provider Communication in End-of-Life Decision-Making.

PubMed

Wilson, Tracey; Haut, Cathy; Akintade, Bimbola

2017-01-01

Critical care providers are responsible for many aspects of patient care, primarily focusing on preserving life. However, nearly 40% of patients who are admitted to an adult critical care unit will not survive. Initiating a conversation about end-of-life decision-making is a daunting task. Often, health care providers are not trained, experienced, or comfortable facilitating these conversations. This article describes a quality improvement project that identified current views on end-of-life communication in the intensive care unit and potential barriers that obstruct open discussion, and offering strategies for improvement. ©2017 American Association of Critical-Care Nurses.

Conversations with commanders: a tool for organizational learning.

PubMed

Engells, Thomas E; Adcox, William H

2010-01-01

In this article the authors report on how police-developed management concepts--Compstat and Intelligence-Led Policing--were successfully applied and used to advance organizational learning in a public safety function of an academic medical center.

A Conversation with...Vincent Scully.

ERIC Educational Resources Information Center

Hackney, Sheldon

1995-01-01

Vincent Scully, Yale art historian, discusses urban architecture, classical influences, and the role of technology. He argues for a public architecture that expresses and supports the concept of communities, and discusses the decline and rebirth of American cities. (MJP)

Lift cruise fan V/STOL aircraft conceptual design study T-39 modification. Volume 1: Technical report

NASA Technical Reports Server (NTRS)

Elliott, D. W.

1976-01-01

The conversion of two T-39 aircraft into lift cruise fan research and technology vehicles is discussed. The concept is based upon modifying the T-39A (NA265-40) Sabreliner airframe into a V/STOL configuration by incorporating two LCF-459 lift cruise fans and three YJ-97 gas generators. The propulsion concept provides the thrust for horizontal flight or lift for vertical flight by deflection of bifurcated nozzles while maintaining engine out safety throughout the flight envelope. The configuration meets all the study requirements specified for the design with control powers in VTOL and conversion in excess of the requirement making it an excellent vehicle for research and development. The study report consists of two volumes; Volume 1 (Reference a) contains background data detailed description and technical substantiation of the aircraft. Volume 2 includes cost data, scheduling and program planning not addressed in Volume 1.

The Energy Conversation: The First 3 Years

DTIC Science & Technology

2009-07-01

Office of Naval Research CNA Robert J. Murray, CNA President and CEO Mitzi Wertheim, Director of The Energy Conversation Printed in the United States of... Mitzi Wertheim and flew out to Washington, DC to meet her for lunch. Wertheim had been Woolsey’s Deputy Under Secretary of the Navy. She is also the

Video-Based Interaction, Negotiation for Comprehensibility, and Second Language Speech Learning: A Longitudinal Study

ERIC Educational Resources Information Center

Saito, Kazuya; Akiyama, Yuka

2017-01-01

This study examined the impact of video-based conversational interaction on the longitudinal development (one academic semester) of second language production by college-level Japanese English-as-a-foreign-language learners. Students in the experimental group engaged in weekly dyadic conversation exchanges with native speakers in the United States…

Finnish Eyes on Border Schools: Teacher Educators Compare Notes

ERIC Educational Resources Information Center

Kralovec, Etta; Dervin, Fred; Riitaoja, Anna-Leena

2017-01-01

This article offers readers the opportunity to eavesdrop on a conversation between teacher educators from Finland and the United States at the conclusion of a field research project conducted in border schools in Arizona. The conversation ranges across topics central to schooling in both countries and exposes educational practices that are not…

Metric Conversion in the Construction Industries--Technical Issues and Status.

ERIC Educational Resources Information Center

Milton, Hans J.; Berry, Sandra A.

This Special Publication was prepared at the request of the Metric Symposium Planning Committee of the National Institute of Building Sciences (NIBS). It is intended to provide information on technical issues and status of metric conversion in the United States construction industries. It was made available to attendees at the NIBS Symposium on…

Fire regimes approaching historic norms reduce wildfire-facilitated conversion from forest to non-forest

Treesearch

Ryan B. Walker; Jonathan D. Coop; Sean A. Parks; Laura Trader

2018-01-01

Extensive high-severity wildfires have driven major losses of ponderosa pine and mixed-conifer forests in the southwestern United States, in some settings catalyzing enduring conversions to nonforested vegetation types. Management interventions to reduce the probability of stand-replacing wildfire have included mechanical fuel treatments, prescribed fire, and wildfire...

Writing for the Ear: Strengthening Oral Style in Manuscript Speeches

ERIC Educational Resources Information Center

Bruss, Kristine

2012-01-01

Public speaking texts typically advise speakers to avoid using a manuscript. Speaking from a manuscript can limit eye contact, reduce expressiveness, and bore listeners. The ideal, rather, is to sound conversational. Conversational style is inclusive, suggesting that a speaker is ""of the people," united in understanding, values and purpose." If a…

Educating Citizens: A Cross-Cultural Conversation

ERIC Educational Resources Information Center

Adler, Susan A.; Moi, Kho Ee

2011-01-01

This study explores pre-service teachers' beliefs about citizenship across two nations, the United States and Singapore; the nature of their conversation about those beliefs; and the impact of their cross-cultural dialog on their reflections about the citizenship goal of social studies. Data is based on a Black Board-based threaded dialog, over…

Report of the 64th National Conference on Weights and Measures

NASA Astrophysics Data System (ADS)

Wollin, H. F.; Babeoq, L. E.; Heffernan, A. P.

1980-03-01

Major issues discussed at this conference include metric conversion in the United States, particularly the conversion of gasoline dispensers, problems relating to the quantity fill of packaged commodities especially as affected by moisture loss and statistical approach to package checking. Federal grain inspection, and a legal metrology control system are also discussed.

43 CFR 3140.2-3 - Application requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Conversion of Existing Oil and Gas Leases and Valid Claims Based on Mineral Locations § 3140.2-3 Application... existing oil and gas lease or valid claim or for an area of proposed unit operation. (d) The plan of operations shall identify by lease number all Federal oil and gas leases proposed for conversion and identify...

43 CFR 3140.2-3 - Application requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Conversion of Existing Oil and Gas Leases and Valid Claims Based on Mineral Locations § 3140.2-3 Application... existing oil and gas lease or valid claim or for an area of proposed unit operation. (d) The plan of operations shall identify by lease number all Federal oil and gas leases proposed for conversion and identify...

43 CFR 3140.2-3 - Application requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Conversion of Existing Oil and Gas Leases and Valid Claims Based on Mineral Locations § 3140.2-3 Application... existing oil and gas lease or valid claim or for an area of proposed unit operation. (d) The plan of operations shall identify by lease number all Federal oil and gas leases proposed for conversion and identify...

43 CFR 3140.2-3 - Application requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Conversion of Existing Oil and Gas Leases and Valid Claims Based on Mineral Locations § 3140.2-3 Application... existing oil and gas lease or valid claim or for an area of proposed unit operation. (d) The plan of operations shall identify by lease number all Federal oil and gas leases proposed for conversion and identify...

Dose estimation for astronauts using dose conversion coefficients calculated with the PHITS code and the ICRP/ICRU adult reference computational phantoms.

PubMed

Sato, Tatsuhiko; Endo, Akira; Sihver, Lembit; Niita, Koji

2011-03-01

Absorbed-dose and dose-equivalent rates for astronauts were estimated by multiplying fluence-to-dose conversion coefficients in the units of Gy.cm(2) and Sv.cm(2), respectively, and cosmic-ray fluxes around spacecrafts in the unit of cm(-2) s(-1). The dose conversion coefficients employed in the calculation were evaluated using the general-purpose particle and heavy ion transport code system PHITS coupled to the male and female adult reference computational phantoms, which were released as a common ICRP/ICRU publication. The cosmic-ray fluxes inside and near to spacecrafts were also calculated by PHITS, using simplified geometries. The accuracy of the obtained absorbed-dose and dose-equivalent rates was verified by various experimental data measured both inside and outside spacecrafts. The calculations quantitatively show that the effective doses for astronauts are significantly greater than their corresponding effective dose equivalents, because of the numerical incompatibility between the radiation quality factors and the radiation weighting factors. These results demonstrate the usefulness of dose conversion coefficients in space dosimetry. © Springer-Verlag 2010

Lunar electric power systems utilizing the SP-100 reactor coupled to dynamic conversion systems

NASA Technical Reports Server (NTRS)

Harty, Richard B.; Durand, Richard E.

1993-01-01

An integration study was performed by Rocketdyne under contract to NASA-LeRC. The study was concerned with coupling an SP-0100 reactor to either a Brayton or Stirling power conversion system. The application was for a surface power system to supply power requirements to a lunar base. A power level of 550 kWe was selected based on the NASA Space Exploration Initiative 90-day study. Reliability studies were initially performed to determine optimum power conversion redundancy. This study resulted in selecting three operating engines and one stand-by unit. Integration design studies indicated that either the Brayton or Stirling power conversion systems could be integrated with the PS-100 reactor. The Stirling system had an integration advantage because of smaller piping size and fewer components. The Stirling engine, however, is more complex and heavier than the Brayton rotating unit, which tends to off-set the Stirling integration advantage. From a performance consideration, the Brayton had a 9 percent mass advantage, and the Stirling had a 50 percent radiator advantage.

Climate change adaptation for the US national wildlife refuge system

Treesearch

Brad Griffith; J. Michael Scott; Robert Adamcik; Daniel Ashe; Brian Czech; Robert Fischman; Patrick Gonzalez; Joshua Lawler; A. David McGuire; Anna Pidgorna

2009-01-01

Since its establishment in 1903, the National Wildlife Refuge System (NWRS) has grown to 635 units and 37 Wetland Management Districts in the United States and its territories. These units provide the seasonal habitats necessary for migratory waterfowl and other species to complete their annual life cycles. Habitat conversion and fragmentation, invasive species,...

SPOKEN AYACUCHO QUECHUA, UNITS 11-20.

ERIC Educational Resources Information Center

PARKER, GARY J.; SOLA, DONALD F.

THE ESSENTIALS OF AYACUCHO GRAMMAR WERE PRESENTED IN THE FIRST VOLUME OF THIS SERIES, SPOKEN AYACUCHO QUECHUA, UNITS 1-10. THE 10 UNITS IN THIS VOLUME (11-20) ARE INTENDED FOR USE IN AN INTERMEDIATE OR ADVANCED COURSE, AND PRESENT THE STUDENT WITH LENGTHIER AND MORE COMPLEX DIALOGS, CONVERSATIONS, "LISTENING-INS," AND DICTATIONS AS WELL…

Assessing Quantitative Learning With The Math You Need When You Need It

NASA Astrophysics Data System (ADS)

Wenner, J. M.; Baer, E. M.; Burn, H.

2008-12-01

We present new data from a pilot project using the The Math You Need, When You Need It (TMYN) web resources in conjunction with several introductory geoscience courses. TMYN is a series of NSF-supported, NAGT-sponsored, web-based modular resources designed to help students learn (or relearn) mathematical skills essential for success in introductory geoscience courses. TMYN presents mathematical topics that are relevant to introductory geoscience based on a survey of more than 75 geoscience faculty members. To date, modules include unit conversions, many aspects of graphing, density calculations, rearranging equations and other simple mathematical concepts commonly used in the geosciences. The modular nature of the resources make it simple to select the units that are appropriate for a given course. In the fall of 2008, nine TMYN modules were tested in three courses taught at Highline Community College (Geology 101) and University of Wisconsin Oshkosh (Physical and Environmental Geology). Over 300 students participated in the study by taking pre- and post-tests and completing modules relevant to their course. Feedback about the use of these modules has been mixed. Initial results confirm anecdotal evidence that students initially have difficulty applying mathematical concepts to geologic problems. Furthermore, pre- test results indicate that, although instructors assume that students can perform simple mathematical manipulations, many students arrive in courses without the skills to apply mathematical concepts in problem solving situations. TMYN resources effectively provide support for learning quantitative problem solving and a mechanism for students to engage in self-teaching. Although we have seen mixed results due to a range of instructor engagement with the material, TMYN can have significant effect on students who are math phobic or "can't do math" because they can work at their own pace to overcome affective obstacles such as fear and dislike of mathematics. TMYN is most effective when instructors make explicit connections between material in the modules and course content. Instructors who participated in the study in Fall 2008 reacted positively to the use of TMYN in introductory geoscience courses because the resources require minimal class and prep time. Furthermore, when instructors can hold students responsible for the quantitative concepts covered with TMYN, they feel more comfortable including quantitative information without significant loss of geologic content.

Research of the impact of coupling between unit cells on performance of linear-to-circular polarization conversion metamaterial with half transmission and half reflection

NASA Astrophysics Data System (ADS)

Guo, Mengchao; Zhou, Kan; Wang, Xiaokun; Zhuang, Haiyan; Tang, Dongming; Zhang, Baoshan; Yang, Yi

2018-04-01

In this paper, the impact of coupling between unit cells on the performance of linear-to-circular polarization conversion metamaterial with half transmission and half reflection is analyzed by changing the distance between the unit cells. An equivalent electrical circuit model is then built to explain it based on the analysis. The simulated results show that, when the distance between the unit cells is 23 mm, this metamaterial converts half of the incident linearly-polarized wave into reflected left-hand circularly-polarized wave and converts the other half of it into transmitted left-hand circularly-polarized wave at 4.4 GHz; when the distance is 28 mm, this metamaterial reflects all of the incident linearly-polarized wave at 4.4 GHz; and when the distance is 32 mm, this metamaterial converts half of the incident linearly-polarized wave into reflected right-hand circularly-polarized wave and converts the other half of it into transmitted right-hand circularly-polarized wave at 4.4 GHz. The tunability is realized successfully. The analysis shows that the changes of coupling between unit cells lead to the changes of performance of this metamaterial. The coupling between the unit cells is then considered when building the equivalent electrical circuit model. The built equivalent electrical circuit model can be used to perfectly explain the simulated results, which confirms the validity of it. It can also give help to the design of tunable polarization conversion metamaterials.

Wind tunnel test of a variable-diameter tiltrotor (VDTR) model

NASA Technical Reports Server (NTRS)

Matuska, David; Dale, Allen; Lorber, Peter

1994-01-01

This report documents the results from a wind tunnel test of a 1/6th scale Variable Diameter Tiltrotor (VDTR). This test was a joint effort of NASA Ames and Sikorsky Aircraft. The objective was to evaluate the aeroelastic and performance characteristics of the VDTR in conversion, hover, and cruise. The rotor diameter and nacelle angle of the model were remotely changed to represent tiltrotor operating conditions. Data is presented showing the propulsive force required in conversion, blade loads, angle of attack stability and simulated gust response, and hover and cruise performance. This test represents the first wind tunnel test of a variable diameter rotor applied to a tiltrotor concept. The results confirm some of the potential advantages of the VDTR and establish the variable diameter rotor a viable candidate for an advanced tiltrotor. This wind tunnel test successfully demonstrated the feasibility of the Variable Diameter rotor for tilt rotor aircraft. A wide range of test points were taken in hover, conversion, and cruise modes. The concept was shown to have a number of advantages over conventional tiltrotors such as reduced hover downwash with lower disk loading and significantly reduced longitudinal gust response in cruise. In the conversion regime, a high propulsive force was demonstrated for sustained flight with acceptable blade loads. The VDTR demonstrated excellent gust response capabilities. The horizontal gust response correlated well with predictions revealing only half the response to turbulence of the conventional civil tiltrotor.

Manned maneuvering unit mission definition study. Volume 3: MMU ancillary support equipment and attachment concepts

NASA Technical Reports Server (NTRS)

1975-01-01

An analysis of Manned Maneuvering Units (MMU) ancillary support equipment and attachment concepts is presented. The major objectives of the study are defined as: (1) identifying MMU applications which would supplement space shuttle safety and effectiveness, (2) to define general MMU performance and control requirements to satisfy candidate shuttle applications, (3) to develop concepts for attaching MMUs to various worksites and equipment, and (4) to identify requirements and develop concepts for MMU ancillary equipment.

The unit field sanitation team: a square peg in a round hole.

PubMed

Bosetti, Timothy; Bridges, Davin

2009-01-01

Basic field sanitation and hygiene is a lost art in today's modern Army. Today, more than ever, there is a need for the unit field sanitation team (FST) to serve as advisors to unit commanders in the area of basic field sanitation and hygiene. Soldiers should know how to construct field latrines, construct waste disposal devices, conduct pest management and control activities, disinfect field water supplies, and practice personal hygiene under field conditions. The current unit FST concept is centered on company-sized formations operating in open terrain. This concept does not support current operations, transformed formations, rapidly changing doctrine, and the expeditionary nature of the Army. This article does not present a new concept, but rather a new look at an existing concept and practice based upon the lessons-learned and after-action reports from the Global War on Terrorism to support the Army in transformation during an era of persistent conflict.

Handling Density Conversion in TPS.

PubMed

Isobe, Tomonori; Mori, Yutaro; Takei, Hideyuki; Sato, Eisuke; Tadano, Kiichi; Kobayashi, Daisuke; Tomita, Tetsuya; Sakae, Takeji

2016-01-01

Conversion from CT value to density is essential to a radiation treatment planning system. Generally CT value is converted to the electron density in photon therapy. In the energy range of therapeutic photon, interactions between photons and materials are dominated with Compton scattering which the cross-section depends on the electron density. The dose distribution is obtained by calculating TERMA and kernel using electron density where TERMA is the energy transferred from primary photons and kernel is a volume considering spread electrons. Recently, a new method was introduced which uses the physical density. This method is expected to be faster and more accurate than that using the electron density. As for particle therapy, dose can be calculated with CT-to-stopping power conversion since the stopping power depends on the electron density. CT-to-stopping power conversion table is also called as CT-to-water-equivalent range and is an essential concept for the particle therapy.

Energy Conversion Alternatives Study (ECAS), General Electric Phase 1. Volume 1: Executive summary. [using coal or coal derived fuels

NASA Technical Reports Server (NTRS)

Corman, J. C.

1976-01-01

A data base for the comparison of advanced energy conversion systems for utility applications using coal or coal-derived fuels was developed. Estimates of power plant performance (efficiency), capital cost, cost of electricity, natural resource requirements, and environmental intrusion characteristics were made for ten advanced conversion systems. Emphasis was on the energy conversion system in the context of a base loaded utility power plant. All power plant concepts were premised on meeting emission standard requirements. A steam power plant (3500 psig, 1000 F) with a conventional coal-burning furnace-boiler was analyzed as a basis for comparison. Combined cycle gas/steam turbine system results indicated competitive efficiency and a lower cost of electricity compared to the reference steam plant. The Open-Cycle MHD system results indicated the potential for significantly higher efficiency than the reference steam plant but with a higher cost of electricity.

Carbon dioxide conversion over carbon-based nanocatalysts.

PubMed

Khavarian, Mehrnoush; Chai, Siang-Piao; Mohamed, Abdul Rahman

2013-07-01

The utilization of carbon dioxide for the production of valuable chemicals via catalysts is one of the efficient ways to mitigate the greenhouse gases in the atmosphere. It is known that the carbon dioxide conversion and product yields are still low even if the reaction is operated at high pressure and temperature. The carbon dioxide utilization and conversion provides many challenges in exploring new concepts and opportunities for development of unique catalysts for the purpose of activating the carbon dioxide molecules. In this paper, the role of carbon-based nanocatalysts in the hydrogenation of carbon dioxide and direct synthesis of dimethyl carbonate from carbon dioxide and methanol are reviewed. The current catalytic results obtained with different carbon-based nanocatalysts systems are presented and how these materials contribute to the carbon dioxide conversion is explained. In addition, different strategies and preparation methods of nanometallic catalysts on various carbon supports are described to optimize the dispersion of metal nanoparticles and catalytic activity.

The NASA program in Space Energy Conversion Research and Technology

NASA Astrophysics Data System (ADS)

Mullin, J. P.; Flood, D. J.; Ambrus, J. H.; Hudson, W. R.

The considered Space Energy Conversion Program seeks advancement of basic understanding of energy conversion processes and improvement of component technologies, always in the context of the entire power subsystem. Activities in the program are divided among the traditional disciplines of photovoltaics, electrochemistry, thermoelectrics, and power systems management and distribution. In addition, a broad range of cross-disciplinary explorations of potentially revolutionary new concepts are supported under the advanced energetics program area. Solar cell research and technology are discussed, taking into account the enhancement of the efficiency of Si solar cells, GaAs liquid phase epitaxy and vapor phase epitaxy solar cells, the use of GaAs solar cells in concentrator systems, and the efficiency of a three junction cascade solar cell. Attention is also given to blanket and array technology, the alkali metal thermoelectric converter, a fuel cell/electrolysis system, and thermal to electric conversion.

The NASA program in Space Energy Conversion Research and Technology

NASA Technical Reports Server (NTRS)

Mullin, J. P.; Flood, D. J.; Ambrus, J. H.; Hudson, W. R.

1982-01-01

The considered Space Energy Conversion Program seeks advancement of basic understanding of energy conversion processes and improvement of component technologies, always in the context of the entire power subsystem. Activities in the program are divided among the traditional disciplines of photovoltaics, electrochemistry, thermoelectrics, and power systems management and distribution. In addition, a broad range of cross-disciplinary explorations of potentially revolutionary new concepts are supported under the advanced energetics program area. Solar cell research and technology are discussed, taking into account the enhancement of the efficiency of Si solar cells, GaAs liquid phase epitaxy and vapor phase epitaxy solar cells, the use of GaAs solar cells in concentrator systems, and the efficiency of a three junction cascade solar cell. Attention is also given to blanket and array technology, the alkali metal thermoelectric converter, a fuel cell/electrolysis system, and thermal to electric conversion.

Development of a novel ice-resistant semisubmersible drilling unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, E.N.; Schloerb, D.W.; Yashima, N.

1983-05-01

A multiyear program was initiated by ARCO Alaska, Inc. to assess the operational feasibility of drilling operations year-round in the ice-covered waters of the Bering, Chukchi, and Beaufort Seas. ARCO Alaska, Inc. is considering several alternative concepts for year-round drilling in the Bering Sea. One such concept, the Ice-Resistant Semisubmersible Drilling Unit, is a design concept of Mitsui Engineering and Shipbuilding Company. The design is intended to operate in broken, continuous, and ridged sea ice, and withstand severe open water sea conditions. The requirement to operate in two dissimilar environments results in a unit that is somewhat unusual when comparedmore » to typical semisubmersible drilling units.« less

The Role of Protected Areas in the Avoidance of Anthropogenic Conversion in a High Pressure Region: A Matching Method Analysis in the Core Region of the Brazilian Cerrado

PubMed Central

Paiva, Rodrigo José Oliveira; Brites, Ricardo Seixas; Machado, Ricardo Bomfim

2015-01-01

Global efforts to avoid anthropogenic conversion of natural habitat rely heavily on the establishment of protected areas. Studies that evaluate the effectiveness of these areas with a focus on preserving the natural habitat define effectiveness as a measure of the influence of protected areas on total avoided conversion. Changes in the estimated effectiveness are related to local and regional differences, evaluation methods, restriction categories that include the protected areas, and other characteristics. The overall objective of this study was to evaluate the effectiveness of protected areas to prevent the advance of the conversion of natural areas in the core region of the Brazil’s Cerrado Biome, taking into account the influence of the restriction degree, governmental sphere, time since the establishment of the protected area units, and the size of the area on the performance of protected areas. The evaluation was conducted using matching methods and took into account the following two fundamental issues: control of statistical biases caused by the influence of covariates on the likelihood of anthropogenic conversion and the non-randomness of the allocation of protected areas throughout the territory (spatial correlation effect) and the control of statistical bias caused by the influence of auto-correlation and leakage effect. Using a sample design that is not based on ways to control these biases may result in outcomes that underestimate or overestimate the effectiveness of those units. The matching method accounted for a bias reduction in 94–99% of the estimation of the average effect of protected areas on anthropogenic conversion and allowed us to obtain results with a reduced influence of the auto-correlation and leakage effects. Most protected areas had a positive influence on the maintenance of natural habitats, although wide variation in this effectiveness was dependent on the type, restriction, governmental sphere, size and age group of the unit. PMID:26222140

In Service to the Nation: Air Force Research Institute Strategic Concept for 2018-2023

DTIC Science & Technology

2009-01-01

must integrate at every level of operational planning and execution. The key to successful strategic communication lies in understanding that de ...Institute strategic concept for 2018–2023 / John A. Shaud. p. ; cm. Includes bibliographical references. ISBN 978-1-58566-189-3 1. Military planning ...United States. 2. United States—Air Force—Forecasting. 3. Strategic plan - ning—United States—Military aspects. 4. United States—Air Force—Operational

Cotton gin trash in the western United States: Resource inventory and energy conversion characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haase, S.G.; Quinn, M.W.; Whittier, J.P.

1993-12-31

The disposal of wastes associated with the processing of cotton is posing increasing problems for cotton gin operators in the western United States. Traditional disposal methods, such as open-air incineration and landfilling are no longer adequate due to increasing environmental concerns. This paper evaluates the technical, economic and environmental feasibility for cotton gin trash to serve as an energy resource. Cotton gin trash has been quantified, by county, in the five cotton-growing states of the western United States. The energy conversion technology that appears to offer the most promise is gasification. An economic evaluation model has been developed that willmore » allow gin operators to analyze their own situation to determine the profitability of converting gin trash to energy.« less

Tdp studies and tests for C. A. Energia Electrica de Venezuela (enelven) at planta ramon laguna, units RL-17 and RL-10. Volume 1. Executive summary, RL-17 test report, and gas conversion proposals. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-03-28

The study, conducted by Babcock and Wilcox, was funded by the U.S. Trade and Development agency on behalf of Enelven. In order to maximize generated power output and minimize operating costs at Planta Ramon Laguna, tests were done to evaluate the condition of equipment at the plant. In order to identify any damage and determine the operating output of each unit, assessments were done of the furnaces, boilers, generators and boiler feed pumps being used in the plant. The report presents the results of these tests. This is the first of three volumes and it is divided into the followingmore » sections: (1) Executive Summary; (2) Hydrogen Damage Assessment; (3) RL-17 Gas Conversion Proposal; (4) RL-10 and RL-11 Gas Conversion Proposals.« less

Postoperative Conversion Disorder Presenting as Inspiratory Stridor and Hemiparesis in a Pediatric Patient.

PubMed

Nelson, Erik J; Wu, Jennifer Y

2017-01-17

BACKGROUND Postoperative conversion disorder is rare and has been reported. The diagnosis is usually made after all major organic causes have been ruled out. CASE REPORT We describe a case of a 13-year-old female who presented in the post-anesthesia care unit with acute-onset inspiratory stridor and unresponsiveness to verbal or painful stimuli after receiving a general anesthetic for upper endoscopy. Later in the post-anesthesia care unit, she presented with acute-onset right hemiplegia and sensory loss. She was first evaluated for causes of her stridor and unresponsiveness. The evaluation revealed paradoxical vocal cord movement, and all laboratory test values were normal. For her hemiplegia and sensory loss, she was evaluated for stroke with head MRI and CT scans, which were normal. CONCLUSIONS After extensive workup and consideration of multiple etiologies for her presenting signs and symptoms, the most likely diagnosis was conversion disorder.

Conversion of an 800 MW oil fired generating unit to burn Orimulsion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blum, J.; Halpin, M.; Morgan, D.

1998-07-01

Florida Power and Light Company (FPL) is proposing to convert the two existing 800 megawatt (MW) residual oil fired generating units at its Manatee Plant located in Parrish, Florida, to burn Ormulsion. Ormulsion is the registered trademark name for a mixture of water and a naturally occurring heavy hydrocarbon known as bitumen. Orimulsion, which originates in Venezuela, will be shipped to Port Manatee in double-hulled vessels, stored at FPL's existing Port Manatee Terminal, and transported via FPL's existing fuel pipeline to the Manatee Plant. The proposed conversion involves modifications of the existing fuel handling facilities, enhancements of the boiler heatmore » transfer surfaces and soot blowing system, and addition of new pollution control equipment. The Manatee Orimulsion conversion will result in overall environmental benefits and significant savings to FPL's customers. This paper summarizes the overall objectives of the project and briefly describes these modifications.« less

Conversion of an 800 MW oil fired generating unit to burn Orimulsion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blum, J.; Halpin, M.; Morgan, D.

1998-04-01

Florida Power & Light Company (FPL) is proposing to convert the two existing 800 megawatt (MW) residual oil fired generating units at its Manatee Plant located in Parrish, Florida, to burn Orimulsion. Orimulsion is the registered trademark name for a mixture of water and a naturally occurring heavy hydrocarbon known as bitumen. Orimulsion, which originates in Venezuela, will be shipped to Port Manatee in double-hulled vessels, stored at FPL`s existing Port Manatee Terminal, and transported via FPL`s existing fuel pipeline to the Manatee Plant. The proposed conversion involves modifications of the existing fuel handling facilities, enhancements of the boiler heatmore » transfer surfaces and soot blowing system, and addition of new pollution control equipment. The Manatee Orimulsion conversion will result in overall environmental benefits and significant savings to FPL`s customers. This paper summarizes the overall objectives of the project and briefly describes these modifications.« less

The elementary school teachers’ ability in the length measurement

NASA Astrophysics Data System (ADS)

Julie, Hongki

2017-09-01

The purpose of this study was to describe the elementary school teachers' mathematical ability (1) to develop students’ activities which constructed longer than, shorter than, and as long as concepts, (2) to develop students’ activities which constructed standard unit on the length measurement, and (3) to develop a problem which used by student to construct why a conversion activity on the unit of the length was useful in the daily life after they have participated in the Realistic Mathematics Education (RME) workshops. Curry and Outhread said if teachers knew more about the growth of students’ conceptual understanding of the length, they would be better able to teach that topic [4]. Therefore, in the workshop, teachers were asked to learn more on the stages of the measurement teaching and learning process and why each stage was important. This capability was described by the results of a test which was content of four problems given to teachers after they have attended the workshop. Research subjects in this study were 14 elementary school teachers at Yogyakarta. The results of the study were as follows: (1) only four of 14 teachers who had the first ability; (2) all teachers had the second ability; and (3) all the teachers did not have the third ability.

An exergy approach to efficiency evaluation of desalination

NASA Astrophysics Data System (ADS)

Ng, Kim Choon; Shahzad, Muhammad Wakil; Son, Hyuk Soo; Hamed, Osman A.

2017-05-01

This paper presents an evaluation process efficiency based on the consumption of primary energy for all types of practical desalination methods available hitherto. The conventional performance ratio has, thus far, been defined with respect to the consumption of derived energy, such as the electricity or steam, which are susceptible to the conversion losses of power plants and boilers that burned the input primary fuels. As derived energies are usually expressed by the units, either kWh or Joules, these units cannot differentiate the grade of energy supplied to the processes accurately. In this paper, the specific energy consumption is revisited for the efficacy of all large-scale desalination plants. In today's combined production of electricity and desalinated water, accomplished with advanced cogeneration concept, the input exergy of fuels is utilized optimally and efficiently in a temperature cascaded manner. By discerning the exergy destruction successively in the turbines and desalination processes, the relative contribution of primary energy to the processes can be accurately apportioned to the input primary energy. Although efficiency is not a law of thermodynamics, however, a common platform for expressing the figures of merit explicit to the efficacy of desalination processes can be developed meaningfully that has the thermodynamic rigor up to the ideal or thermodynamic limit of seawater desalination for all scientists and engineers to aspire to.

In My Opinion. A New Sign Conversion for Geometrical Optics.

ERIC Educational Resources Information Center

Ditteon, Richard

1993-01-01

Introduces a new sign convention for the object and image distances involving mirrors and lenses. Proposes that the method is easier for students to understand and remember and that it helps clarify the physics concepts involved. (MDH)

Double-Drachma Teaching.

ERIC Educational Resources Information Center

Rogers, Joseph A.

1981-01-01

A hypothetical conversation with Euclid engenders the concept of rooting education in instruction that is both affirmative and dimensional. The curriculum should reflect the material context in which we live rather than abstract theory shrouded in social, political, psychological, and linguistic verbiage. (Author/WD)

Railway Transportation Engineering (CEE 408) Course updates and online conversion.

DOT National Transportation Integrated Search

2017-01-20

The new order of lectures provides students with a sound introduction to the main concepts behind efficiency and economic railway operations. This naturally follows into the design of railcars for safe, efficient and economical operations. With railc...

Advanced Concepts and Methods of Approximate Reasoning

DTIC Science & Technology

1989-12-01

immeasurably by numerous conversations and discussions with Nadal Bat- tle, Hamid Berenji , Piero Bonissone, Bernadette Bouchon-Meunier, Miguel Delgado, Di...comments of Claudi Alsina, Hamid Berenji , Piero Bonissone, Didier Dubois, Francesc Esteva, Oscar Firschein, Marty Fischler, Pascal Fua, Maria Angeles

High carbon losses due to recent cropland expansion in the United States

NASA Astrophysics Data System (ADS)

Spawn, S.; Lark, T.; Gibbs, H.

2017-12-01

Land conversion for agriculture in the United States has reached record highs in recent years. From 2008 to 2012 nearly 30,000 square kilometers of previously un-cultivated land were converted to agricultural land use with much of this expansion occurring on grasslands (77%) and shrublands (8%). To understand the effects of this conversion on global C cycling, we created novel, spatially explicit biomass maps for these biomes by combining existing satellite data products with models derived from field measurements. We then estimated changes in existing C stocks by combining our derived data with existing Landsat-scale data on land cover, land conversion, forest biomass and soil organic carbon (C) stocks. We find that conversion results in annual C losses of approximately 25 Tg C from US terrestrial ecosystems. Nationwide, roughly 80% of total emissions result from committed soil organic C losses. While biomass losses from expansion into forests and wetlands are disproportionately high per unit area, the vast majority of C losses occurred in grassland ecosystems, with grassland roots representing close to 70% of total biomass losses across all biomes. C losses are partially offset each year by agricultural abandonment which we estimate could sequester as much as 15 Tg C, annually. Taken together, we find that US agricultural expansion results in net annual emissions of 10 Tg C which is nearly 30% of emissions from existing US croplands. Our estimate is comparable to a recent analogous estimate for conversion of the Brazilian Cerrado and is equivalent to 10% of annual C losses from pantropical deforestation, suggesting that the effects of US cropland expansion could be globally significant.

Tunable, self-powered integrated arc plasma-melter vitrification system for waste treatment and resource recovery

DOEpatents

Titus, Charles H.; Cohn, Daniel R.; Surma, Jeffrey E.

1998-01-01

The present invention provides a relatively compact self-powered, tunable waste conversion system and apparatus which has the advantage of highly robust operation which provides complete or substantially complete conversion of a wide range of waste streams into useful gas and a stable, nonleachable solid product at a single location with greatly reduced air pollution to meet air quality standards. The system provides the capability for highly efficient conversion of waste into high quality combustible gas and for high efficiency conversion of the gas into electricity by utilizing a high efficiency gas turbine or by an internal combustion engine. The solid product can be suitable for various commercial applications. Alternatively, the solid product stream, which is a safe, stable material, may be disposed of without special considerations as hazardous material. In the preferred embodiment of the invention, the arc plasma furnace and joule heated melter are formed as a fully integrated unit with a common melt pool having circuit arrangements for the simultaneous independently controllable operation of both the arc plasma and the joule heated portions of the unit without interference with one another. The preferred configuration of this embodiment of the invention utilizes two arc plasma electrodes with an elongated chamber for the molten pool such that the molten pool is capable of providing conducting paths between electrodes. The apparatus may additionally be employed with reduced or without further use of the gases generated by the conversion process. The apparatus may be employed as a self-powered or net electricity producing unit where use of an auxiliary fuel provides the required level of electricity production.

A process concept for the production of benzene-ethylene-SNG from coal using flash hydropyrolysis technology

NASA Astrophysics Data System (ADS)

Greene, M. I.; Ladelfa, C. J.; Bivacca, S. J.

1980-05-01

Flash hydropyrolysis (FHP) of coal is an emerging technology for the direct production of methane, ethane and BTX in a single-stage, high throughput reactor. The FHP technique involves the short residence time (1-2 seconds), rapid heatup of coal in a dilute-phase, transport reactor. When integrated into an overall, grass-roots conversion complex, the FHP technique can be utilized to generate a product consisting of SNG, ethylene/propylene, benzene and Fischer-Tropsch-based alcohols. This paper summarizes the process engineering and economics of conceptualized facility based on an FHP reactor operation with a lignitic coal. The plant is hypothetically sited near the extensive lignite fields located in the Texas region of the United States. Utilizing utility-financing methods for the costing of SNG, and selling the chemicals cogenerated at petrochemical market prices, the 20-year average SNG cost has been computed to vary between $3-4/MM Btu, depending upon the coal costs, interest rates, debt/equity ratio, coproduct chemicals prices, etc.

Gambling, games of skill and human ecology: a pilot study by a multidimensional analysis approach.

PubMed

Valera, Luca; Giuliani, Alessandro; Gizzi, Alessio; Tartaglia, Francesco; Tambone, Vittoradolfo

2015-01-01

The present pilot study aims at analyzing the human activity of playing in the light of an indicator of human ecology (HE). We highlighted the four essential anthropological dimensions (FEAD), starting from the analysis of questionnaires administered to actual gamers. The coherence between theoretical construct and observational data is a remarkable proof-of-concept of the possibility of establishing an experimentally motivated link between a philosophical construct (coming from Huizinga's Homo ludens definition) and actual gamers' motivation pattern. The starting hypothesis is that the activity of playing becomes ecological (and thus not harmful) when it achieves the harmony between the FEAD, thus realizing HE; conversely, it becomes at risk of creating some form of addiction, when destroying FEAD balance. We analyzed the data by means of variable clustering (oblique principal components) so to experimentally verify the existence of the hypothesized dimensions. The subsequent projection of statistical units (gamers) on the orthogonal space spanned by principal components allowed us to generate a meaningful, albeit preliminary, clusterization of gamer profiles.

Hybrid micro-scale photovoltaics for enhanced energy conversion across all irradiation conditions

NASA Astrophysics Data System (ADS)

Agrawal, Gautam

A novel hybrid photovoltaics (HPV) architecture is presented that integrates high-performance micro-optics-based concentrator photovoltaics (CPV) array technology with a 1-sun photovoltaic (PV) cell within a low-profile panel structure. The approach simultaneously captures the direct solar radiation components with arrayed high-efficiency CPV cells and the diffuse solar components with an underlying wide-area PV cell. Performance analyses predict that the hybrid approach will significantly enhance the average energy produced per unit area for the full range of diffuse/direct radiation patterns across the USA. Furthermore, cost analyses indicate that the hybrid concept may be financially attractive for a wide range of locations. Indoor and outdoor experimental evaluation of a micro-optical system designed for use in a hybrid architecture verified that a large proportion of the direct radiation component was concentrated onto emulated micro-cell regions while most of the diffuse radiation and the remaining direct radiation was collected in the 1-sun cell area.

Topological energy storage of work generated by nanomotors.

PubMed

Weysser, Fabian; Benzerara, Olivier; Johner, Albert; Kulić, Igor M

2015-01-28

Most macroscopic machines rely on wheels and gears. Yet, rigid gears are entirely impractical on the nano-scale. Here we propose a more useful method to couple any rotary engine to any other mechanical elements on the nano- and micro-scale. We argue that a rotary molecular motor attached to an entangled polymer energy storage unit, which together form what we call the "tanglotron" device, is a viable concept that can be experimentally implemented. We derive the torque-entanglement relationship for a tanglotron (its "equation of state") and show that it can be understood by simple statistical mechanics arguments. We find that a typical entanglement at low packing density costs around 6kT. In the high entanglement regime, the free energy diverges logarithmically close to a maximal geometric packing density. We outline several promising applications of the tanglotron idea and conclude that the transmission, storage and back-conversion of topological entanglement energy are not only physically feasible but also practical for a number of reasons.

Video image processor on the Spacelab 2 Solar Optical Universal Polarimeter /SL2 SOUP/

NASA Technical Reports Server (NTRS)

Lindgren, R. W.; Tarbell, T. D.

1981-01-01

The SOUP instrument is designed to obtain diffraction-limited digital images of the sun with high photometric accuracy. The Video Processor originated from the requirement to provide onboard real-time image processing, both to reduce the telemetry rate and to provide meaningful video displays of scientific data to the payload crew. This original concept has evolved into a versatile digital processing system with a multitude of other uses in the SOUP program. The central element in the Video Processor design is a 16-bit central processing unit based on 2900 family bipolar bit-slice devices. All arithmetic, logical and I/O operations are under control of microprograms, stored in programmable read-only memory and initiated by commands from the LSI-11. Several functions of the Video Processor are described, including interface to the High Rate Multiplexer downlink, cosmetic and scientific data processing, scan conversion for crew displays, focus and exposure testing, and use as ground support equipment.

Conversion of Coal Mine Gas to LNG

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This project evolved from a 1995, DOE-NETL competitive solicitation for practical CMM capture and utilization concepts. Appalachian Pacific was one of three companies selected to proceed with the construction and operation of a cost-shared demonstration plant. In the course of trying to proceed with this demonstration plant, AP examined several liquefaction technologies, discussed obtaining rights to coal mine methane with a number of coal companies, explored marketing potential with a wide variety of customers in many sections of the United States, studied in great detail the impact of a carbon credit exchange, and developed a suite of analytical tools withmore » which to evaluate possible project options. In the end, the newness of the product, reluctance on the part of the coal companies to venture away from time tested practices, difficulty with obtaining financing, the failure of a carbon credit market to develop and the emergence of shale derived gas production prevented a demonstration plant from being built.« less

When Your Pregnancy Echoes Your Illness: Transition to Motherhood With Inflammatory Bowel Disease.

PubMed

Ghorayeb, Jihane; Branney, Peter; Selinger, Christian P; Madill, Anna

2018-03-01

Our aim is to provide an understanding of the experience of women with inflammatory bowel disease (IBD) who have made the transition to motherhood. A total of 22 mothers with IBD were recruited from around the United Kingdom. Semi-structured interviews were conducted and analyzed using thematic analysis. The central concept- Blurred Lines-offers a novel frame for understanding the transition to motherhood with IBD through identifying parallels between having IBD and becoming, and being, a mother. Parallels clustered into three main themes: Need for Readiness, Lifestyle Changes, and Monitoring Personal and Physical Development. Hence, women with IBD are in some ways well prepared for the challenges of motherhood even though, as a group, they tend to restrict their reproductive choices. We recommend health professionals initiate conversations about reproduction early and provide a multidisciplinary approach to pregnancy and IBD in which women have confidence that their ongoing treatment will be integrated successfully with their maternity care.

Electronic photography: a new age of medical imaging?

PubMed

Tübergen, D; Manegold, B C

1993-07-01

This is a critical overview of present conceptions of the introduction of electronic photography in medicine. It is not a complete list of products, rather it is a description of how the requirements of the physician have influenced medical illustration in the past and will continue to do so in the future. Video systems are widely used in medicine. Besides the learning and teaching of effects of television, minimal invasive surgery (MIS) has become reality through endoscopy, rapidly accepted worldwide. Documentation of endoscopic procedures and their effects is becoming routine. Therefore, the conversion of complex optical information into binary units is a logical development to save space for storage. The reproduction, storage and transfer of detailed images is already realized by digital camera systems, photo CD, scanners and picture archiving and communicating system (PACS). Now electronic imaging in medicine has to be regarded as a matter of routine. The real impact of accelerated editing will be shown in the future.

KWU's high conversion reactor concept - An economical evolution of modern pressurized water reactor technology toward improved uranium ore utilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Markl, H.; Goetzmann, C.A.; Moldaschl, H.

The Kraftwerk Union AG high conversion reactor represents a quasi-standard PWR with fuel assemblies of more or less uniformly enriched fuel rods, arranged in a tight hexagonal array with a pitch-to-diameter ratio p/d approx. = 1.12. High fuel enrichment as well as a high conversion ratio of --0.9 will provide the potential for high burnup values up to 70 000 MWd/tonne and a low fissile material consumption. The overall objective of the actual RandD program is to have the technical feasibility, including that for licensibility, established by the early 1990s as a prerequisite for deciding whether to enter a demonstrationmore » plant program.« less

The Quasi-Human Child: How Normative Conceptions of Childhood Enabled Neoliberal School Reform in the United States

ERIC Educational Resources Information Center

Sonu, Debbie; Benson, Jeremy

2016-01-01

This paper argues that normative conceptions of the child, as a natural quasi-human being in need of guidance, enable current school reforms in the United States to directly link the child to neoliberal aims and objectives. In using Foucault's concept of governmentality and disciplinary power, we first present how the child is constructed as a…

Selective optical contacting for solar spectrum management

NASA Astrophysics Data System (ADS)

Yang, Jianfeng; Chen, Weijian; Wang, Bo; Zhang, Zhilong; Huang, Shujuan; Shrestha, Santosh; Wen, Xiaoming; Patterson, Robert; Conibeer, Gavin

2017-02-01

Solar spectrum management using up/down conversion is an important method to improve the photovoltaic energy conversion efficiency. It asks for a monochromatic luminescence absorption at the band edge of the photovoltaic device to reduce both the sub-band-gap and over-band-gap energy losses. Here, we demonstrate an energy selective optical contacting concept to improve the luminescence transfer efficiency for spectrum management. By increasing both the luminescence emission and re-absorption ability through photonic resonance, an efficient photon transfer channel could be established between the luminescence emitter and the photovoltaic component in a near-field region. This concept is not only able to compensate the insufficient band edge absorption ability of the photovoltaic device, but also to break the far-field limitation of luminescence radiation. The energy selection on the optical spectrum naturally imposed by the mode resonance is also helpful to improve the monochromaticity of the luminescence yield. In this paper, a photonic crystal cavity is used to realize the optical contacting concept between a thin silicon film and spectrum converter. The optical power and photon flux transferred between different components are calculated analytically using the electromagnetic Green's function. The corresponding radiative dipole moment is estimated by the fluctuation-dissipation theorem. The example shows an over 80 times enhancement in the luminescence absorbance by the silicon layer, illustrating the great potential of this concept to be applied on nano-structured photovoltaic devices.

How Soon Will We Measure in Metric?

ERIC Educational Resources Information Center

Weaver, Kenneth F.

1977-01-01

A brief history of measurement systems beginning with the Egyptians and Babylonians is given, ending with a discussion of the metric system and its adoption by the United States. Tables of metric prefixes, metric units, and common metric conversions are included. (MN)

Teaching Basic Geographical Skills: Map and Compass Activities.

ERIC Educational Resources Information Center

Trussell, Margaret Edith

1986-01-01

Presents a unit on map and compass activities which introduces compass direction, magnetic declination and conversion of map measurement to familiar units. Requires four, one-hour class meetings and may be followed by a half-day orienteering activity. (Author/JDH)

Elementary Career Education Units for Integration in Subject Areas at Grades Kindergarten through Six. Project SPAN.

ERIC Educational Resources Information Center

Bell, Lorraine P., Comp.

Units in the curriculum guide are presented in two sections, K-3 and 4-6, and emphasize hands-on activities, role-playing, resource persons, field trips, and classroom career corners. Organized on the career cluster concept, the K-3 units cover self-concept, home and family, familiar community occupations, zoo animals, travel, school, and the…

Potential for Increasing the Output of Existing Hydroelectric Plants.

DTIC Science & Technology

1981-06-01

existing units to higher generating capacity by rehabilitating, modifying or replacing turbines and/or generators; increasing the effective...loss in converting fluid energy (flow and head) to mechanical energy ( turbine output) to electrical energy (generator output). The significant practical...opportunity is improvement of the energy conversion efficiency of the hydraulic turbine since the energy conversion efficiency of electrical

College Writing in China and America: A Modest and Humble Conversation, with Writing Samples

ERIC Educational Resources Information Center

Sullivan, Patrick; Zhang, Yufeng; Zheng, Fenglan

2012-01-01

This article is a pragmatic, classroom-focused conversation about the teaching of writing among three teachers living in the United States and China, separated by many thousands of miles and many centuries of tradition and culture. Our focus here is on classroom concerns: actual student writing, assignment design, and assessment. We seek to…

Joining the Conversation: Twitter as a Tool for Student Political Engagement

ERIC Educational Resources Information Center

Journell, Wayne; Ayers, Cheryl A.; Beeson, Melissa Walker

2013-01-01

This article describes possibilities afforded by using social media, specifically Twitter, as a way to encourage students to join political conversations across the United States and around the world. In this study, we describe a project in which students used Twitter to share commentary about the state of the 2012 presidential election. The…

Strange Fruit Indeed: Interrogating Contemporary Textbook Representations of Racial Violence toward African Americans

ERIC Educational Resources Information Center

Brown, Anthony L.; Brown, Keffrelyn D.

2010-01-01

Background/Context: Recent racial incidents on college and high school campuses throughout the United States have catalyzed a growing conversation around issues of race and racism. These conversations exist alongside ongoing concerns about the lack of attention given to race and racism in the official school curriculum. Given that the field of…

A Survey of Preparation for Metric Changeover among Supervisors of Science and Mathematics at the State Department of Education Level.

ERIC Educational Resources Information Center

Trueblood, Cecil R.; And Others

1981-01-01

Described is the Northeast Metric Education Consortium survey to study the status of metric conversion throughout the United States. The six categories in the survey included teacher certification practices, status of full metric conversion, state's commitment to metrics, state supervisors' budgetary needs, state metric-resources availability, and…

First Aid Lessons. Correlated Conversation for Use with "You Can Give First Aid." Workplace Curriculum.

ERIC Educational Resources Information Center

Cacy, Roselynn; Smith, Polly

This unit contains lesson plans designed to teach first aid skills to adults with limited language skills. The lesson plans were developed, using the Laubach literacy method, for a workplace literacy project in Anchorage, Alaska. The lesson plans, which are correlated with the book, "You Can Give First Aid," include conversational skills…

Space-based solar power conversion and delivery systems study. Volume 2: Engineering analysis

NASA Technical Reports Server (NTRS)

1977-01-01

The technical and economic feasibility of Satellite Solar Power Systems was studied with emphasis on the analysis and definition of an integrated strawman configuration concept, from which credible cost data could be estimated. Specifically, system concepts for each of the major subprogram areas were formulated, analyzed, and iterated to the degree necessary for establishing an overall, workable baseline system design. Cost data were estimated for the baseline and used to conduct economic analyses. The baseline concept selected was a 5-GW crystal silicon truss-type photovoltaic configuration, which represented the most mature concept available. The overall results and major findings, and the results of technical analyses performed during the final phase of the study efforts are reported.

A critique of social capital.

PubMed

Navarro, Vicente

2002-01-01

This article critiques the concepts of communitarianism and social capital as used in the United States and in Europe. For the United States, the author focuses on Robert Putnam's understanding of both concepts, showing that the apolitical analysis of the Progressive Era, of the progressive developments in Northern Italy, and of the situation of labor unions in the United States is not only insufficient but wrong. The critique also includes the difference between U.S. communitarianism and its European versions, Christian democracy and New Labour, and the limitations of both approaches. The uses and misuses of these concepts in the political debate are discussed.

SPOKEN COCHABAMBA QUECHUA, UNITS 1-12.

ERIC Educational Resources Information Center

LASTRA, YOLANDA; SOLA, DONALD F.

THE FIRST OF TWO VOLUMES PREPARED FOR TEACHING THE COCHABAMBA DIALECT OF QUECHUA TO SPEAKERS OF ENGLISH, THIS DOCUMENT IS MADE UP OF 12 UNITS THAT COMPRISE A 6-WEEK INTENSIVE COURSE OF 20 CLASS HOURS A WEEK. EACH UNIT CONSISTS OF ONE OR MORE DIALOGS TO BE MEMORIZED, A DIALOG REVIEW, A SECTION ON GRAMMAR WITH ACCOMPANYING EXERCISES, CONVERSATION,…

Thin film solar cells: research in an industrial perspective.

PubMed

Edoff, Marika

2012-01-01

Electricity generation by photovoltaic conversion of sunlight is a technology in strong growth. The thin film technology is taking market share from the dominant silicon wafer technology. In this article, the market for photovoltaics is reviewed, the concept of photovoltaic solar energy conversion is discussed and more details are given about the present technological limitations of thin film solar cell technology. Special emphasis is given for solar cells which employ Cu(In,Ga)Se(2) and Cu(2)ZnSn(S,Se)(4) as the sunlight-absorbing layer.

dc analysis and design of zero-voltage-switched multi-resonant converters

NASA Astrophysics Data System (ADS)

Tabisz, Wojciech A.; Lee, Fred C.

Recently introduced multiresonant converters (MRCs) provide zero-voltage switching (ZVS) of both active and passive switches and offer a substantial reduction of transistor voltage stress and an increase of load range, compared to their quasi-resonant converter counterparts. Using the resonant switch concept, a simple, generalized analysis of ZVS MRCs is presented. The conversion ratio and voltage stress characteristics are derived for basic ZVS MRCs, including buck, boost, and buck/boost converters. Based on the analysis, a design procedure that optimizes the selection of resonant elements for maximum conversion efficiency is proposed.

The classification of conversion disorder (functional neurologic symptom disorder) in ICD and DSM.

PubMed

Levenson, J L; Sharpe, M

2016-01-01

The name given to functional neurologic symptoms has evolved over time in the different editions of the International Classification of Diseases (ICD) and the Diagnostic and Statistical Manual of Mental Disorders (DSM), reflecting a gradual move away from an etiologic conception rooted in hysterical conversion to an empiric phenomenologic one, emphasizing the central role of the neurologic examination and testing in demonstrating that the symptoms are incompatible with recognized neurologic disease pathophysiology, or are internally inconsistent. © 2016 Elsevier B.V. All rights reserved.

A Power Conversion Concept for the Jupiter Icy Moons Orbiter

NASA Technical Reports Server (NTRS)

Mason, Lee S.

2003-01-01

The Jupiter Icy Moons Orbiter (JIMO) is a bold new mission under development by the Office of Space Science at NASA Headquarters. ITMO is examining the potential of Nuclear Electric Propulsion (NEP) technology to efficiently deliver scientific payloads to three Jovian moons: Callisto, Ganymede, and Europa. A critical element of the NEP vehicle is the reactor power system, consisting of the nuclear reactor, power conversion, heat rejection, and power management and distribution (PMAD). The emphasis of this paper is on the non-nuclear elements of the reactor power system.

Language Matters in Counselling Diversity

ERIC Educational Resources Information Center

Lee, Billy

2017-01-01

The paper presents a personal view of some issues around therapeutic conversations involving difference and minority experience. Language, discourse and mother-tongue are explored from different theoretical standpoints and considered alongside concepts of difference, otherness and the unvoiced. Intercultural counselling offers a framework for…

Free-Piston Stirling Engines

NASA Technical Reports Server (NTRS)

Shaltens, Richard K.

1989-01-01

Engines promise cost-effective solar-power generation. Report describes two concepts for Stirling-engine systems for conversion of solar heat to electrical energy. Recognized most promising technologies for meeting U.S. Department of Energy goals for performance and cost for terrestrial electrical-energy sources.

Glossary of terms and table of conversion factors used in design of chemical propulsion systems

NASA Technical Reports Server (NTRS)

Keller, R. B., Jr. (Compiler)

1979-01-01

The glossary presented is based entirely on terms used in the monographs on Chemical Propulsion. Significant terms relating to material properties and to material fabrication are presented. The terms are arranged in alphabetical order, with multiple word terms appearing in the normal sequence of usage; for example, ablative cooling appears as such, not as cooling, ablative, and lip seal appears as such, not as seal, lip. Conversion Factors for converting U.S. customary units to the International System of Units are presented in alphabetical order of the physical quantity (e.g., density, heat flux, specific impulse) involved.

Keep It in Proportion.

ERIC Educational Resources Information Center

Snider, Richard G.

1985-01-01

The ratio factors approach involves recognizing a given fraction, then multiplying so that units cancel. This approach, which is grounded in concrete operational thinking patterns, provides a standard for science ratio and proportion problems. Examples are included for unit conversions, mole problems, molarity, speed/density problems, and…

Exploring Linear Measure.

ERIC Educational Resources Information Center

Cox, Philip L.

This material is an instructional unit on measuring and estimating. A variety of activities are used with manipulative devices, worksheets, and discussion questions included. Major topics are estimating lengths, accuracy of measurement, metric system, scale drawings, and conversion between different units. A teacher's guide is also available.…

A review of HOV lane performance and policy options in the United States

DOT National Transportation Integrated Search

2008-12-01

The report provides an assessment of performance of existing HOV lane facilities in the United States, and explores policy alternatives and effects related to conversion of existing HOV lanes to HOT lane operations. The report includes sketch plannin...

Recent Rates of Forest Harvest and Conversion in North America

NASA Technical Reports Server (NTRS)

Masek, Jeffrey G.; Cohen, Warren B.; Leckie, Donald; Wulder, Michael A.; Vargas, Rodrigo; de Jong, Ben; Healey, Sean; Law, Beverly; Birdsey, Richard; Houghton, R. A.;

Systems definition space based power conversion systems: Executive summary

NASA Technical Reports Server (NTRS)

1977-01-01

Potential space-located systems for the generation of electrical power for use on earth were investigated. These systems were of three basic types: (1) systems producing electrical power from solar energy; (2) systems producing electrical power from nuclear reactors; (3) systems for augmenting ground-based solar power plants by orbital sunlight reflectors. Configurations implementing these concepts were developed through an optimization process intended to yield the lowest cost for each. A complete program was developed for each concept, identifying required production rates, quantities of launches, required facilities, etc. Each program was costed in order to provide the electric power cost appropriate to each concept.

Children's Understanding and Knowledge of Conception and Birth: Comparing Children from England, the Netherlands, Sweden, and the United States

ERIC Educational Resources Information Center

Caron, Sandra L.; Ahlgrim, Carie Jo

2012-01-01

The present study replicated research conducted decades earlier (Goldman & Goldman, 1982a; Koch, 197480) on what children in the United States know about conception and birth compared to those in other countries. Specifically, response drawings by 48 six-year-old boys and girls from England, the Netherlands, Sweden, and the United States were…

Inversion Concept of the Origin of Life

NASA Astrophysics Data System (ADS)

Kompanichenko, V. N.

2012-06-01

The essence of the inversion concept of the origin of life can be narrowed down to the following theses: 1) thermodynamic inversion is the key transformation of prebiotic microsystems leading to their transition into primary forms of life; 2) this transformation might occur only in the microsystems oscillating around the bifurcation point under far-from-equilibrium conditions. The transformation consists in the inversion of the balance "free energy contribution / entropy contribution", from negative to positive values. At the inversion moment the microsystem radically reorganizes in accordance with the new negentropy (i.e. biological) way of organization. According to this approach, the origin-of-life process on the early Earth took place in the fluctuating hydrothermal medium. The process occurred in two successive stages: a) spontaneous self-assembly of initial three-dimensional prebiotic microsystems composed mainly of hydrocarbons, lipids and simple amino acids, or their precursors, within the temperature interval of 100-300°C (prebiotic stage); b) non-spontaneous synthesis of sugars, ATP and nucleic acids started at the inversion moment under the temperature 70-100°C (biotic stage). Macro- and microfluctuations of thermodynamic and physico-chemical parameters able to sustain this way of chemical conversion have been detected in several contemporary hydrothermal systems. A minimal self-sufficient unit of life on the early Earth was a community of simplest microorganisms (not a separate microorganism).

Practical implementation of the concept of converted electric vehicle with advanced traction and dynamic performance and environmental safety indicators

NASA Astrophysics Data System (ADS)

Sidorov, K. M.; Yutt, V. E.; Grishchenko, A. G.; Golubchik, T. V.

2018-02-01

The objective of the work presented in this paper is to describe the implementation of the technical solutions have been developed, with regard to structure, composition, and characteristics, for an experimental prototype of an electric vehicle which has been converted from a conventional vehicle. The methodology of the study results is based on the practical implementation of the developed concept of the conversion of conventional vehicles into electric vehicles. The main components of electric propulsion system of the experimental prototype of electric vehicle are developed and manufactured on the basis of computational researches, taking into account the criteria and principles of conversion within the framework of presented work. The article describes a schematic and a design of power conversion and commutation electrical equipment, traction battery, electromechanical transmission. These results can serve as guidance material in the design and implementation of electric propulsion system (EPS) components of electric vehicles, facilitate the development of optimal technical solutions in the development and manufacture of vehicles, including those aimed at autonomy of operation and the use of perspective driver assistance systems. As part of this work, was suggested a rational structure for an electric vehicle experimental prototype, including technical performance characteristics of the components of EPS.

Multi-megawatt power system trade study

NASA Astrophysics Data System (ADS)

Longhurst, Glen R.; Schnitzler, Bruce G.; Parks, Benjamin T.

2002-01-01

A concept study was undertaken to evaluate potential multi-megawatt power sources for nuclear electric propulsion. The nominal electric power requirement was set at 15 MWe with an assumed mission profile of 120 days at full power, 60 days in hot standby, and another 120 days of full power, repeated several times for 7 years of service. Two configurations examined were (1) a gas-cooled reactor based on the NERVA Derivative design, operating a closed cycle Brayton power conversion system; and (2) a molten metal-cooled reactor based on SP-100 technology, driving a boiling potassium Rankine power conversion system. This study considered the relative merits of these two systems, seeking to optimize the specific mass. Conclusions were that either concept appeared capable of reaching the specific mass goal of 3-5 kg/kWe estimated to be needed for this class of mission, though neither could be realized without substantial development in reactor fuels technology, thermal radiator mass and volume efficiency, and power conversion and distribution electronics and systems capable of operating at high temperatures. The gas-Brayton system showed a specific mass advantage (3.17 vs 6.43 kg/kWe for the baseline cases) under the set of assumptions used and eliminated the need to deal with two-phase working fluid flows in the microgravity environment of space. .

A tribal abstraction network for SNOMED CT target hierarchies without attribute relationships.

PubMed

Ochs, Christopher; Geller, James; Perl, Yehoshua; Chen, Yan; Agrawal, Ankur; Case, James T; Hripcsak, George

2015-05-01

Large and complex terminologies, such as Systematized Nomenclature of Medicine-Clinical Terms (SNOMED CT), are prone to errors and inconsistencies. Abstraction networks are compact summarizations of the content and structure of a terminology. Abstraction networks have been shown to support terminology quality assurance. In this paper, we introduce an abstraction network derivation methodology which can be applied to SNOMED CT target hierarchies whose classes are defined using only hierarchical relationships (ie, without attribute relationships) and similar description-logic-based terminologies. We introduce the tribal abstraction network (TAN), based on the notion of a tribe-a subhierarchy rooted at a child of a hierarchy root, assuming only the existence of concepts with multiple parents. The TAN summarizes a hierarchy that does not have attribute relationships using sets of concepts, called tribal units that belong to exactly the same multiple tribes. Tribal units are further divided into refined tribal units which contain closely related concepts. A quality assurance methodology that utilizes TAN summarizations is introduced. A TAN is derived for the Observable entity hierarchy of SNOMED CT, summarizing its content. A TAN-based quality assurance review of the concepts of the hierarchy is performed, and erroneous concepts are shown to appear more frequently in large refined tribal units than in small refined tribal units. Furthermore, more erroneous concepts appear in large refined tribal units of more tribes than of fewer tribes. In this paper we introduce the TAN for summarizing SNOMED CT target hierarchies. A TAN was derived for the Observable entity hierarchy of SNOMED CT. A quality assurance methodology utilizing the TAN was introduced and demonstrated. © The Author 2014. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Employing inquiry-based computer simulations and embedded scientist videos to teach challenging climate change and nature of science concepts

NASA Astrophysics Data System (ADS)

Cohen, Edward Charles

Design based research was utilized to investigate how students use a greenhouse effect simulation in order to derive best learning practices. During this process, students recognized the authentic scientific process involving computer simulations. The simulation used is embedded within an inquiry-based technology-mediated science curriculum known as Web-based Inquiry Science Environment (WISE). For this research, students from a suburban, diverse, middle school setting use the simulations as part of a two week-long class unit on climate change. A pilot study was conducted during phase one of the research that informed phase two, which encompasses the dissertation. During the pilot study, as students worked through the simulation, evidence of shifts in student motivation, understanding of science content, and ideas about the nature of science became present using a combination of student interviews, focus groups, and students' conversations. Outcomes of the pilot study included improvements to the pedagogical approach. Allowing students to do "Extreme Testing" (e.g., making the world as hot or cold as possible) and increasing the time for free exploration of the simulation are improvements made as a result of the findings of the pilot study. In the dissertation (phase two of the research design) these findings were implemented in a new curriculum scaled for 85 new students from the same school during the next school year. The modifications included new components implementing simulations as an assessment tool for all students and embedded modeling tools. All students were asked to build pre and post models, however due to technological constraints these were not an effective tool. A non-video group of 44 students was established and another group of 41 video students had a WISE curriculum which included twelve minutes of scientists' conversational videos referencing explicit aspects on the nature of science, specifically the use of models and simulations in science. The students in the video group had marked improvement compared to the non-video group on questions regarding modeling as a tool for representing objects and processes of science modeling aspects as evident by multiple data sources. The findings from the dissertation have potential impacts on improving Nature of Science (NOS) concepts around modeling by efficiently embedding short authentic scientific videos that can be easily used by many educators. Compared to published assessments by the American Association for the Advancement of Science (AAAS), due to the curriculum interventions both groups scored higher than the average United States middle school student on many NOS and climate content constructs.

Employing Inquiry-Based Computer Simulations and Embedded Scientist Videos To Teach Challenging Climate Change and Nature of Science Concepts

NASA Astrophysics Data System (ADS)

Cohen, E.

2013-12-01

Design based research was utilized to investigate how students use a greenhouse effect simulation in order to derive best learning practices. During this process, students recognized the authentic scientific process involving computer simulations. The simulation used is embedded within an inquiry-based technology-mediated science curriculum known as Web-based Inquiry Science Environment (WISE). For this research, students from a suburban, diverse, middle school setting use the simulations as part of a two week-long class unit on climate change. A pilot study was conducted during phase one of the research that informed phase two, which encompasses the dissertation. During the pilot study, as students worked through the simulation, evidence of shifts in student motivation, understanding of science content, and ideas about the nature of science became present using a combination of student interviews, focus groups, and students' conversations. Outcomes of the pilot study included improvements to the pedagogical approach. Allowing students to do 'Extreme Testing' (e.g., making the world as hot or cold as possible) and increasing the time for free exploration of the simulation are improvements made as a result of the findings of the pilot study. In the dissertation (phase two of the research design) these findings were implemented in a new curriculum scaled for 85 new students from the same school during the next school year. The modifications included new components implementing simulations as an assessment tool for all students and embedded modeling tools. All students were asked to build pre and post models, however due to technological constraints these were not an effective tool. A non-video group of 44 students was established and another group of 41 video students had a WISE curriculum which included twelve minutes of scientists' conversational videos referencing explicit aspects on the nature of science, specifically the use of models and simulations in science. The students in the video group had marked improvement compared to the non-video group on questions regarding modeling as a tool for representing objects and processes of science modeling aspects as evident by multiple data sources. The findings from the dissertation have potential impacts on improving Nature of Science (NOS) concepts around modeling by efficiently embedding short authentic scientific videos that can be easily used by many educators. Compared to published assessments by the American Association for the Advancement of Science (AAAS), due to the curriculum interventions both groups scored higher than the average United States middle school student on many NOS and climate content constructs.

Patterns of empathy as embodied practice in clinical conversation—a musical dimension

PubMed Central

Buchholz, Michael B.

2014-01-01

Cognitive linguistics and conversation analysis (a) converge in the analysis of category bound activities and (b) in viewing thinking and talking as embodied activities. The first aim of this paper is to outline these powerful theories as useful tools for the analysis of enacting empathy. The second aim is to outline these theories as useful tools for the analysis of how empathy is co-enacted in clinical conversation documented in transcripts. Cognitive Linguistics and Conversation Analysis converge in detecting patterns of I-You-relationships with roots in early preverbal embodied protoconversation continuing to more symbolic conversational level. The paper proposes to describe this continuity of empathic conversation in musical metaphors like balance, rhythm and resonance. In a first section transcripts from therapeutic sessions are presented. In a second section linguistic and other research data are presented in order to bring empirical data to this new conception of how empathy can be understood, how it is done and how two participants cooperate to enact empathy. Ideas for further research are outlined. PMID:24817855

SPS energy conversion and power management workshop. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-06-01

In 1977 a four year study, the concept Development and Evaluation Program, was initiated by the US Department of Energy and the National Aeronautics and Space Administration. As part of this program, a series of peer reviews were carried out within the technical community to allow available information on SPS to be sifted, examined and, if need be, challenged. The SPS Energy Conversion and Power Management Workshop, held in Huntsville, Alabama, February 5 to 7, 1980, was one of these reviews. The results of studies in this particular field were presented to an audience of carefully selected scientists and engineers.more » This first report summarizes the results of that peer review. It is not intended to be an exhaustive treatment of the subject. Rather, it is designed to look at the SPS energy conversion and power management options in breadth, not depth, to try to foresee any troublesome and/or potentially unresolvable problems and to identify the most promising areas for future research and development. Topics include photovoltaic conversion, solar thermal conversion, and electric power distribution processing and power management. (WHK)« less

Fast conversion of scFv to Fab antibodies using type IIs restriction enzymes.

PubMed

Sanmark, Hanna; Huovinen, Tuomas; Matikka, Tero; Pettersson, Tiina; Lahti, Maria; Lamminmäki, Urpo

2015-11-01

Single chain variable fragment (scFv) antibody libraries are widely used for developing novel bioaffinity reagents, although Fab or IgG molecules are the preferred antibody formats in many final applications. Therefore, rapid conversion methods for combining multiple DNA fragments are needed to attach constant domains to the scFv derived variable domains. In this study we describe a fast and easy cloning method for the conversion of single framework scFv fragments to Fab fragments using type IIS restriction enzymes. All cloning steps excluding plating of the Fab transformants can be done in 96 well plates and the procedure can be completed in one working day. The concept was tested by converting 69 scFv clones into Fab format on 96 well plates, which resulted in 93% success rate. The method is particularly useful as a high-throughput tool for the conversion of the chosen scFv clones into Fab molecules in order to analyze them as early as possible, as the conversion can significantly affect the binding properties of the chosen clones. Copyright © 2015 Elsevier B.V. All rights reserved.