Enhanced microwave absorbing performance of CoNi alloy nanoparticles anchored on a spherical carbon monolith.

PubMed

Li, Na; Hu, Changwen; Cao, Minhua

2013-05-28

CoNi alloy nanoparticles anchored on a spherical carbon monolith (CoNi-C) were prepared by a solvothermal route and subsequent heat treatment without any templates. Their permittivity and permeability behaviors were studied in the frequency range of 2-18 GHz. The CoNi-C composites showed the best microwave absorbing performances compared to those of Co-C and Ni-C. The maximum reflection loss of the CoNi-C nanocomposites can reach -50.2 dB at 7.7 GHz with samples of 4 mm in thickness, better than that of the Ni-C composites, while the Co-C composites showed almost no absorption at all. The absorption mechanism of the three absorbents was also discussed.

Computer-assisted electrochemical fabrication of a highly selective and sensitive amperometric nitrite sensor based on surface decoration of electrochemically reduced graphene oxide nanosheets with CoNi bimetallic alloy nanoparticles.

PubMed

Gholivand, Mohammad-Bagher; Jalalvand, Ali R; Goicoechea, Hector C

2014-07-01

For the first time, a novel, robust and very attractive statistical experimental design (ED) using minimum-run equireplicated resolution IV factorial design (Min-Run Res IV FD) coupled with face centered central composite design (FCCCD) and Derringer's desirability function (DF) was developed to fabricate a highly selective and sensitive amperometric nitrite sensor based on electrodeposition of CoNi bimetallic alloy nanoparticles (NPs) on electrochemically reduced graphene oxide (ERGO) nanosheets. The modifications were characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), energy dispersive X-ray spectroscopic (EDS), scanning electron microscopy (SEM) techniques. The CoNi bimetallic alloy NPs were characterized using digital image processing (DIP) for particle counting (density estimation) and average diameter measurement. Under the identified optimal conditions, the novel sensor detects nitrite in concentration ranges of 0.1-30.0 μM and 30.0-330.0 μM with a limit of detection (LOD) of 0.05 μM. This sensor selectively detects nitrite even in the presence of high concentration of common ions and biological interferents therefore, we found that the sensor is highly selective. The sensor also demonstrated an excellent operational stability and good antifouling properties. The proposed sensor was used to the determination of nitrite in several foodstuff and water samples. Copyright © 2014. Published by Elsevier B.V.

Controllable Interfacial Coupling Effects on the Magnetic Dynamic Properties of Perpendicular [Co/Ni]5/Cu/TbCo Composite Thin Films.

PubMed

Tang, Minghong; Zhao, Bingcheng; Zhu, Weihua; Zhu, Zhendong; Jin, Q Y; Zhang, Zongzhi

2018-02-07

Dynamic magnetic properties in perpendicularly exchange-coupled [Co/Ni] 5 /Cu (t Cu = 0-2 nm)/TbCo structures show strong dependences on the interfacial antiferromagnetic strength J ex , which is controlled by the Cu interlayer thickness. The precession frequency f and effective damping constant α eff of a [Co/Ni] 5 multilayer differ distinctly for parallel (P) and antiparallel (AP) magnetization orientation states. For samples with a thin t Cu , f of the AP state is apparently higher, whereas α eff is lower than that in the P state, owing to the unidirectional exchange bias effect (H EB ) from the TbCo layer. The differences in f and α eff between the two states gradually decrease with increasing t Cu . By using a uniform precession model including an additional H EB term, the field-dependent frequency curves can be well-fitted, and the fitted H EB value is in good agreement with the experimental data. Moreover, the saturation damping constant α 0 displays a nearly linear correlation with J ex . It decreases significantly with J ex and eventually approaches a constant value of 0.027 at t Cu = 2 nm where J ex vanishes. These results provide a better understanding and effective control of magnetization dynamics in exchange-coupled composite structures for spintronic applications.

Controllable Fabrication of Amorphous Co-Ni Pyrophosphates for Tuning Electrochemical Performance in Supercapacitors.

PubMed

Chen, Chen; Zhang, Ning; He, Yulu; Liang, Bo; Ma, Renzhi; Liu, Xiaohe

2016-09-07

Incorporation of two transition metals offers an effective method to enhance the electrochemical performance in supercapacitors for transition metal compound based electrodes. However, such a configuration is seldom concerned in pyrophosphates. Here, amorphous phase Co-Ni pyrophosphates are fabricated as electrodes in supercapacitors. Through controllably adjusting the ratios of Co and Ni as well as the calcination temperature, the electrochemical performance can be tuned. An optimized amorphous Ni-Co pyrophosphate exhibits much higher specific capacitance than monometallic Ni and Co pyrophosphates and shows excellent cycling ability. When employing Ni-Co pyrophosphates as positive electrode and activated carbon as a negative electrode, the fabricated asymmetric supercapacitor cell exhibits favorable capacitance and cycling ability. This study provides facile methods to improve the transition metal pyrophosphate electrodes for efficient electrodes in electrochemical energy storage devices.

Effect of spin transfer torque on domain wall motion regimes in [Co/Ni] superlattice wires

NASA Astrophysics Data System (ADS)

Le Gall, S.; Vernier, N.; Montaigne, F.; Thiaville, A.; Sampaio, J.; Ravelosona, D.; Mangin, S.; Andrieu, S.; Hauet, T.

2017-05-01

The combined effect of magnetic field and current on domain wall motion is investigated in epitaxial [Co/Ni] microwires. Both thermally activated and flow regimes are found to be strongly affected by current. All experimental data can be understood by taking into account both adiabatic and nonadiabatic components of the spin transfer torque, the parameters of which are extracted. In the precessional flow regime, it is shown that the domain wall can move in the electron flow direction against a strong applied field, as previously observed. In addition, for a large range of applied magnetic field and injected current, a stochastic domain wall displacement after each pulse is observed. Two-dimensional micromagnetic simulations, including some disorder, show a random fluctuation of the domain wall position that qualitatively matches the experimental results.

Vertically cross-linked and porous CoNi2S4 nanosheets-decorated SiC nanowires with exceptional capacitive performance as a free-standing electrode for asymmetric supercapacitors

NASA Astrophysics Data System (ADS)

Zhao, Jian; Li, Zhenjiang; Zhang, Meng; Meng, Alan; Li, Qingdang

2016-11-01

In this paper, a simple, low-cost and mild hydrothermal technology of growing vertically cross-linked ternary nickel cobalt sulfides nanosheets (CoNi2S4 NSs) with porous characteristics on SiC nanowires (SiC NWs) supporters with outstanding resistances to oxidation and corrosion, good conductivity and large specific surface area deposited directly on carbon cloth (CC) is successfully developed, forming a new family of free-standing advanced hybrid electrode for asymmetric supercapacitors (ASCs). Such integrated electrode (SiC NWs@CoNi2S4 NSs) manifests intriguing electrochemical characteristics such as high specific capacity (231.1 mA h g-1 at 2 A g-1) and rate capability due to the synergistic effect of SiC NWs and CoNi2S4 NSs with unique morphology. Additionally, an asymmetric supercapacitor is also assembled via using this special hybrid architectures as positive electrode and activated carbon (AC) on Ni foam (NF) as negative electrode, and it can yield a high energy density of 57.8 W h kg-1 with a power density of 1.6 kW kg-1 and long cycling lifespan. This study constitutes an emerging attractive strategy to reasonably design and fabricate novel SiC NWs-based nanostructured electrodes with enhanced capacity, which holds great potential to be the candidate of electrode materials for environmentally benign as well as high-performance energy storage devices.

Thin Co/Ni-based bottom pinned spin-transfer torque magnetic random access memory stacks with high annealing tolerance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomczak, Y., E-mail: Yoann.Tomczak@imec.be; Department of Chemistry, KU Leuven; Swerts, J.

2016-01-25

Spin-transfer torque magnetic random access memory (STT-MRAM) is considered as a replacement for next generation embedded and stand-alone memory applications. One of the main challenges in the STT-MRAM stack development is the compatibility of the stack with CMOS process flows in which thermal budgets up to 400 °C are applied. In this letter, we report on a perpendicularly magnetized MgO-based tunnel junction (p-MTJ) on a thin Co/Ni perpendicular synthetic antiferromagnetic layer with high annealing tolerance. Tunnel magneto resistance (TMR) loss after annealing occurs when the reference layer loses its perpendicular magnetic anisotropy due to reduction of the CoFeB/MgO interfacial anisotropy. Amore » stable Co/Ni based p-MTJ stack with TMR values of 130% at resistance-area products of 9 Ω μm{sup 2} after 400 °C anneal is achieved via moment control of the Co/Ta/CoFeB reference layer. Thinning of the CoFeB polarizing layer down to 0.8 nm is the key enabler to achieve 400 °C compatibility with limited TMR loss. Thinning the Co below 0.6 nm leads to a loss of the antiferromagnetic interlayer exchange coupling strength through Ru. Insight into the thickness and moment engineering of the reference layer is displayed to obtain the best magnetic properties and high thermal stability for thin Co/Ni SAF-based STT-MRAM stacks.« less

Electrospinning preparation, characterization and magnetic properties of cobalt-nickel ferrite (Co(1-x)Ni(x)Fe2)O4) nanofibers.

PubMed

Xiang, Jun; Chu, Yanqiu; Shen, Xiangqian; Zhou, Guangzhen; Guo, Yintao

2012-06-15

Uniform Co(1-)(x)Ni(x)Fe(2)O(4) (x=0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) nanofibers with average diameter of 110 nm and length up to several millimeters were prepared by calcination of electrospun precursor nanofibers containing polymer and inorganic salts. The as-spun and calcined nanofibers were characterized in detail by TG-DTA, XRD, FE-SEM, TEM, SAED and VSM, respectively. The effect of composition of the nanofibers on the structure and magnetic properties were investigated. The nanofibers are formed through assembling magnetic nanoparticles with poly(vinyl pyrrolidone) as the structure-directing template. The structural characteristics and magnetic properties of the resultant nanofibers vary with chemical composition and can be tuned by adjusting the Co/Ni ratio. Both lattice parameter and particle size decrease gradually with increasing nickel concentration. The saturation magnetization and coercivity lie in the range 29.3-56.4 emu/g and 210-1255 Oe, respectively, and both show a monotonously decreasing behavior with the increase in nickel concentration. Such changes in magnetic properties can mainly be attributed to the lower magnetocrystalline anisotropy and the smaller magnetic moment of Ni(2+) ions compared to Co(2+) ions. Furthermore, the coercivity of Co-Ni ferrite nanofibers is found to be superior to that of the corresponding nanoparticle counterparts, presumably due to their large shape anisotropy. These novel one-dimensional Co-Ni ferrite magnetic nanofibers can potentially be used in micro-/nanoelectronic devices, microwave absorbers and sensing devices. Copyright © 2012 Elsevier Inc. All rights reserved.

Tuning Electrochemical Properties of Li-Rich Layered Oxide Cathodes by Adjusting Co/Ni Ratios and Mechanism Investigation Using in situ X-ray Diffraction and Online Continuous Flow Differential Electrochemical Mass Spectrometry.

PubMed

Shen, ShouYu; Hong, YuHao; Zhu, FuChun; Cao, ZhenMing; Li, YuYang; Ke, FuSheng; Fan, JingJing; Zhou, LiLi; Wu, LiNa; Dai, Peng; Cai, MingZhi; Huang, Ling; Zhou, ZhiYou; Li, JunTao; Wu, QiHui; Sun, ShiGang

2018-04-18

Owing to high specific capacity of ∼250 mA h g -1 , lithium-rich layered oxide cathode materials (Li 1+ x Ni y Co z Mn (3- x-2 y-3 z)/4 O 2 ) have been considered as one of the most promising candidates for the next-generation cathode materials of lithium ion batteries. However, the commercialization of this kind of cathode materials seriously restricted by voltage decay upon cycling though Li-rich materials with high cobalt content have been widely studied and show good capacity. This research successfully suppresses voltage decay upon cycling while maintaining high specific capacity with low Co/Ni ratio in Li-rich cathode materials. Online continuous flow differential electrochemical mass spectrometry (OEMS) and in situ X-ray diffraction (XRD) techniques have been applied to investigate the structure transformation of Li-rich layered oxide materials during charge-discharge process. The results of OEMS revealed that low Co/Ni ratio lithium-rich layered oxide cathode materials released no lattice oxygen at the first charge process, which will lead to the suppression of the voltage decay upon cycling. The in situ XRD results displayed the structure transition of lithium-rich layered oxide cathode materials during the charge-discharge process. The Li 1.13 Ni 0.275 Mn 0.580 O 2 cathode material exhibited a high initial medium discharge voltage of 3.710 and a 3.586 V medium discharge voltage with the lower voltage decay of 0.124 V after 100 cycles.

Biological abatement of enzyme inhibitors

USDA-ARS?s Scientific Manuscript database

Lignocellulose pretreatments release phenolic compounds that cause enzyme inhibition and deactivation. Bio-abatement, the biological removal of furfurals, acetic acid and phenolics, may utilize fungal fermentation to metabolize these compounds to CO2, water, cell mass, and heat. Our work with Coni...

Presence of adhesive vesicles in the mycoherbicide Alternaria helianthi

USDA-ARS?s Scientific Manuscript database

Alternaria helianthi conidia have been shown to cause disease on common cocklebur. Conidia were applied to slides made hydrophobic by coating with dimethyldicholorosilane (mimics leaf surface), then rinsed and treated with FITC-Con A to stain the adhesive material. Alternaria helianthi coni...

Critical Thinking or Cony Cozenage.

ERIC Educational Resources Information Center

Matulich, Loretta

Teachers of history, introductory chemistry, and literature from Portland State University, Portland Community College, Clark College, Mt. Hood Community College, and Clackamas Community College (Oregon) have been working together to foster critical thinking in their students. Teachers in these disciplines have been meeting at their respective…

Elastic Properties of Novel Co- and CoNi-Based Superalloys Determined through Bayesian Inference and Resonant Ultrasound Spectroscopy

NASA Astrophysics Data System (ADS)

Goodlet, Brent R.; Mills, Leah; Bales, Ben; Charpagne, Marie-Agathe; Murray, Sean P.; Lenthe, William C.; Petzold, Linda; Pollock, Tresa M.

2018-06-01

Bayesian inference is employed to precisely evaluate single crystal elastic properties of novel γ -γ ' Co- and CoNi-based superalloys from simple and non-destructive resonant ultrasound spectroscopy (RUS) measurements. Nine alloys from three Co-, CoNi-, and Ni-based alloy classes were evaluated in the fully aged condition, with one alloy per class also evaluated in the solution heat-treated condition. Comparisons are made between the elastic properties of the three alloy classes and among the alloys of a single class, with the following trends observed. A monotonic rise in the c_{44} (shear) elastic constant by a total of 12 pct is observed between the three alloy classes as Co is substituted for Ni. Elastic anisotropy ( A) is also increased, with a large majority of the nearly 13 pct increase occurring after Co becomes the dominant constituent. Together the five CoNi alloys, with Co:Ni ratios from 1:1 to 1.5:1, exhibited remarkably similar properties with an average A 1.8 pct greater than the Ni-based alloy CMSX-4. Custom code demonstrating a substantial advance over previously reported methods for RUS inversion is also reported here for the first time. CmdStan-RUS is built upon the open-source probabilistic programing language of Stan and formulates the inverse problem using Bayesian methods. Bayesian posterior distributions are efficiently computed with Hamiltonian Monte Carlo (HMC), while initial parameterization is randomly generated from weakly informative prior distributions. Remarkably robust convergence behavior is demonstrated across multiple independent HMC chains in spite of initial parameterization often very far from actual parameter values. Experimental procedures are substantially simplified by allowing any arbitrary misorientation between the specimen and crystal axes, as elastic properties and misorientation are estimated simultaneously.

Unifying ultrafast demagnetization and intrinsic Gilbert damping in Co/Ni bilayers with electronic relaxation near the Fermi surface

NASA Astrophysics Data System (ADS)

Zhang, Wei; He, Wei; Zhang, Xiang-Qun; Cheng, Zhao-Hua; Teng, Jiao; Fähnle, Manfred

2017-12-01

The ability to controllably manipulate the laser-induced ultrafast magnetic dynamics is a prerequisite for future high-speed spintronic devices. The optimization of devices requires the controllability of the ultrafast demagnetization time τM and intrinsic Gilbert damping αintr. In previous attempts to establish a relationship between τM and αintr, the rare-earth doping of a permalloy film with two different demagnetization mechanisms was not a suitable candidate. Here, we choose Co/Ni bilayers to investigate the relations between τM and αintr by means of the time-resolved magneto-optical Kerr effect (TR-MOKE) via adjusting the thickness of the Ni layers, and obtain an approximately proportional relation between these two parameters. The remarkable agreement between the TR-MOKE experiment and the prediction of a breathing Fermi-surface model confirms that a large Elliott-Yafet spin-mixing parameter b2 is relevant to the strong spin-orbital coupling at the Co/Ni interface. More importantly, a proportional relation between τM and αintr in such metallic films or heterostructures with electronic relaxation near the Fermi surface suggests the local spin-flip scattering dominates the mechanism of ultrafast demagnetization, otherwise the spin-current mechanism dominates. It is an effective method to distinguish the dominant contributions to ultrafast magnetic quenching in metallic heterostructures by simultaneously investigating both the ultrafast demagnetization time and Gilbert damping. Our work can open an avenue to manipulate the magnitude and efficiency of terahertz emission in metallic heterostructures such as perpendicular magnetic anisotropic Ta/Pt/Co/Ni/Pt/Ta multilayers, and then it has an immediate implication for the design of high-frequency spintronic devices.

Optical second-harmonic diffraction study of anisotropic surface diffusion: CO on Ni(110)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, X.; Zhu, X.D.; Daum, W.

We describe in detail a technique using optical second-harmonic (SH) diffraction from a one-dimensional laser-induced monolayer grating to probe surface diffusion of adsorbates and its anisotropy on a solid surface. The case of CO on Ni(110) is used as a demonstration. The two orthogonal and independent diffusion tensor components along (1{bar 1}0) and (001) are measured, exhibiting a strong anisotropy in both the activation energy {ital E}{sub diff} and the preexponential factor {ital D}{sub 0} in the diffusion coefficients. A compensation effect between {ital E}{sub diff} and {ital D}{sub 0} is observed. In comparison with CO/Ni(111) and CO/Ni(100), our resultmore » suggests that the Ni(110) surface seen by CO is much smoother than Ni(111) and Ni(100). Both advantages and limitations of the present technique are mentioned and possible complications in the data analysis are discussed.« less

Fabrication of cobalt-nickel binary nanowires in a highly ordered alumina template via AC electrodeposition

PubMed Central

2013-01-01

Cobalt-nickel (Co-Ni) binary alloy nanowires of different compositions were co-deposited in the nanopores of highly ordered anodic aluminum oxide (AAO) templates from a single sulfate bath using alternating current (AC) electrodeposition. AC electrodeposition was accomplished without modifying or removing the barrier layer. Field emission scanning electron microscope was used to study the morphology of templates and alloy nanowires. Energy-dispersive X-ray analysis confirmed the deposition of Co-Ni alloy nanowires in the AAO templates. Average diameter of the alloy nanowires was approximately 40 nm which is equal to the diameter of nanopore. X-ray diffraction analysis showed that the alloy nanowires consisted of both hexagonal close-packed and face-centered cubic phases. Magnetic measurements showed that the easy x-axis of magnetization is parallel to the nanowires with coercivity of approximately 706 Oe. AC electrodeposition is very simple, fast, and is useful for the homogenous deposition of various secondary nanostuctured materials into the nanopores of AAO. PMID:23941234

Magnetic properties of Co/Ni grain boundaries after annealing

NASA Astrophysics Data System (ADS)

Coutts, Chris; Arora, Monika; Hübner, René; Heinrich, Bret; Girt, Erol

2018-05-01

Magnetic and microstructural properties of <111> textured Cu/N×[Co/Ni] films are studied as a function of the number of bilayer repeats N and annealing temperature. M(H) loop measurements show that coercivity, Hc, increases with annealing temperature and that the slope of the saturation curve at Hc has a larger reduction for smaller N. An increase of the magnetic anisotropy (Ku) to saturation magnetization (Ms) ratio after annealing N×[Co/Ni] with N < 15 only partially describes the increase to Hc. Energy-dispersive X-ray spectroscopy analyses performed in scanning transmission electron microscopy mode across cross-sections of as-deposited and annealed Cu/16×[Co/Ni] films show that Cu diffuses from the seed layer into grain boundaries of Co/Ni. Diffusion of Cu reduces exchange coupling (Hex) between the magnetic grains and explains the increase in Hc. Additionally, the difference in the slope of the M(H) curves at Hc between the thick (N = 16) and thin (N = 4) magnetic multilayers is due to Cu diffusion more effectively decoupling magnetic grains in the thinner multilayer.

ALARA efforts in nordic BWRs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ingemansson, T.; Lundgren, K.; Elkert, J.

1995-03-01

Some ALARA-related ABB Atom projects are currently under investigation. One of the projects has been ordered by the Swedish Radiation Protection Institute, and two others by the Nordic BWR utilities. The ultimate objective of the projects is to identify and develop methods to significantly decrease the future exposure levels in the Nordic BWRS. As 85% to 90% of the gamma radiation field in the Nordic BWRs originates from Co-60, the only way to significantly decrease the radiation doses is to effect Co and Co-60. The strategy to do this is to map the Co sources and estimate the source strengthmore » of Co from these sources, and to study the possibility to affect the release of Co-60 from the core surfaces and the uptake on system surfaces. Preliminary results indicate that corrosion/erosion of a relatively small number of Stellite-coated valves and/or dust from grinding of Stellite valves may significantly contribute to the Co input to the reactors. This can be seen from a high measured Co/Ni ratio in the feedwater and in the reactor water. If stainless steel is the only source of Co, the Co/Ni ratio would be less than 0.02 as the Co content in the steel is less than 0.2%. The Co/Ni ratio in the reactor water, however, is higher than 0.1, indicating that the major fraction of the Co originates from Stellite-coated valves. There are also other possible explanations for an increase of the radiation fields. The Co-60 inventory on the core surfaces increases approximately as the square of the burn-up level. If the burn-up is increased from 35 to 5 MWd/kgU, the Co-60 inventory on the core surfaces will be doubled. Also the effect on the behavior of Co-60 of different water chemistry and materials conditions is being investigated. Examples of areas studied are Fe and Zn injection, pH-control, and different forms of surface pre-treatments.« less

Paralex: An Environment for Parallel Programming in Distributed Systems

DTIC Science & Technology

1991-12-07

distributed systems is coni- parable to assembly language programming for traditional sequential systems - the user must resort to low-level primitives ...to accomplish data encoding/decoding, communication, remote exe- cution, synchronization , failure detection and recovery. It is our belief that... synchronization . Finally, composing parallel programs by interconnecting se- quential computations allows automatic support for heterogeneity and fault tolerance

Hybrid helical magnetic microrobots obtained by 3D template-assisted electrodeposition.

PubMed

Zeeshan, Muhammad A; Grisch, Roman; Pellicer, Eva; Sivaraman, Kartik M; Peyer, Kathrin E; Sort, Jordi; Özkale, Berna; Sakar, Mahmut S; Nelson, Bradley J; Pané, Salvador

2014-04-09

Hybrid helical magnetic microrobots are achieved by sequential electrodeposition of a CoNi alloy and PPy inside a photoresist template patterned by 3D laser lithography. A controlled actuation of the microrobots by a rotating magnetic field is demonstrated in a fluidic environment. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Interfacial effect on the reverse of magnetization and ultrafast demagnetization in Co/Ni bilayers with perpendicular magnetic anisotropy

NASA Astrophysics Data System (ADS)

Gong, Zi-Zhao; Zhang, Wei; He, Wei; Zhang, Xiang-Qun; Liu, Yong; Cheng, Zhao-Hua

2018-05-01

Not Available Project supported by the National Basic Research Program of China (Grant Nos. 2015CB921403 and 2016YFA0300701), the National Natural Science Foundation of China (Grant Nos. 91622126, 51427801, and 51671212), and the Natural Science Foundation of Hebei Province, China (Grant No. A2015203021).

Ring head recording on perpendicular media: Output spectra for CoCr and CoCr/NiFe media

NASA Astrophysics Data System (ADS)

Stubbs, D. P.; Whisler, J. W.; Moe, C. D.; Skorjanec, J.

1985-04-01

The recording density response for sputtered CoCr (thickness=0.5 μm) and CoCr/NiFe (t=0.25 μm/0.5 μm) as well as evaporated CoNi (t=0.12 μm) and Co surface-doped iron oxide particulate media has been measured by reading and writing with Mn-Zn ferrite heads (gap length=0.375 μm, track width=37 μm) in contact with the media. Measurements to 200 kfc/i (thousand flux changes per inch) show a gap null around 115 kfc/i. The data have been normalized by dividing out the head sensitivity to obtain the value of spacing plus transition width (d+a) for the various media. For the CoCr media this value varied from 0.075-0.088 μm; for CoNi, 0.100 μm, and for the particulate medium, 0.163 μm. In addition, testing with a larger gapped Mn-Zn ferrite head (g=2.43 μm) shows that the head fields are distorted by the soft magnetic underlayer in dual layer CoCr/NiFe samples when the gap length is large compared to the distance to the underlayer.

Advanced Monitoring of Migratory Birds on Military Lands

DTIC Science & Technology

2010-03-01

BRSP Brewer‟s Sparrow BTSP Black - throated Sparrow BLGR Blue Grosbeak CAKI Cassin‟s Kingbird CONI Common Nighthawk EAME Eastern...Fuller et al. 1998). This approach has been used for many species, ranging from Black - throated Sparrow (Amphispiza bilineata, Pidgeon et al 2003) to...lightest yellow indicates a predicted abundance of zero. Species acronym key: BTSP Black - throated Sparrow ; EAME Eastern Meadowlark; WEKI Western

Low temperature synthesis and enhanced electrical properties by substitution of Al3+ and Cr3+ in Co-Ni nanoferrites

NASA Astrophysics Data System (ADS)

Pervaiz, Erum; Gul, I. H.

2013-10-01

Aluminum and chromium substituted Co-Ni spinel nanoferrites were prepared by sol-gel auto combustion method. Structural parameters along with electrical and magnetic properties have been investigated in the present work. Crystallite sizes of nano ferrite estimated from the peak (311) lies in the range of 13-21 nm ±2 nm and compared with crystallite sizes calculated from Williamsons-Hall plots. DC electrical resistivity variations due to the concentration of aluminum and chromium in the host ferrite have been measured from 368 K to 573 K. Increase in the room temperature DC electrical resistivity was observed up to a concentration x=0.2 and then decreases for x >0.2. Dielectric parameters (real and imaginary part of complex permittivity, dielectric loss tangent) were studied as a function of frequency (20 Hz-5 MHz) and a decrease in the dielectric parameters was observed due to substitution of nickel, aluminum and chromium ions in cobalt nanoferrites. AC conductivity, complex impedance and complex electrical modulus were studied as a function of frequency for the conduction and relaxation mechanisms in the present ferrite system. Saturation magnetization, coercivity, canting angles and magneto crystalline anisotropy variations with composition were observed and presented for the present ferrites under an applied magnetic field of 10 kOe at room temperature. It was found that both magnetization and coercivity decreases with increase in the concentration of aluminum and chromium along with a decrease in the anisotropy parameters. High DC resistivity with low dielectric parameters of the present nanoferrites make them suitable for high frequency and electromagnetic wave absorbing devices. High purity mixed Co-Ni-Al-Cr nanoferrites have been prepared by sol-gel auto combustion method. DC electrical resistivity increases due to substitution of Al3+ and Cr3+. Complex permittivity decrease for Co-Ni-Al-Cr nanoferrites. Detailed AC response analysis has been presented for mixed Co-Ni-Al-Cr nanoferrites. Magnetization and coercively reduces for Al3+ and Cr3+ doped Co-Ni ferrite nanoparticles showing that material is becoming soft magnetic.

Muscle Oxygen Supply Impairment during Exercise in Poorly Controlled Type 1 Diabetes

PubMed Central

TAGOUGUI, SEMAH; LECLAIR, ERWAN; FONTAINE, PIERRE; MATRAN, RÉGIS; MARAIS, GAELLE; AUCOUTURIER, JULIEN; DESCATOIRE, AURÉLIEN; VAMBERGUE, ANNE; OUSSAIDENE, KAHINA; BAQUET, GEORGES; HEYMAN, ELSA

2015-01-01

ABSTRACT Purpose Aerobic fitness, as reflected by maximal oxygen (O2) uptake (V˙O2max), is impaired in poorly controlled patients with type 1 diabetes. The mechanisms underlying this impairment remain to be explored. This study sought to investigate whether type 1 diabetes and high levels of glycated hemoglobin (HbA1c) influence O2 supply including O2 delivery and release to active muscles during maximal exercise. Methods Two groups of patients with uncomplicated type 1 diabetes (T1D-A, n = 11, with adequate glycemic control, HbA1c <7.0%; T1D-I, n = 12 with inadequate glycemic control, HbA1c >8%) were compared with healthy controls (CON-A, n = 11; CON-I, n = 12, respectively) matched for physical activity and body composition. Subjects performed exhaustive incremental exercise to determine V˙O2max. Throughout the exercise, near-infrared spectroscopy allowed investigation of changes in oxyhemoglobin, deoxyhemoglobin, and total hemoglobin in the vastus lateralis. Venous and arterialized capillary blood was sampled during exercise to assess arterial O2 transport and factors able to shift the oxyhemoglobin dissociation curve. Results Arterial O2 content was comparable between groups. However, changes in total hemoglobin (i.e., muscle blood volume) was significantly lower in T1D-I compared with that in CON-I. T1D-I also had impaired changes in deoxyhemoglobin levels and increase during high-intensity exercise despite normal erythrocyte 2,3-diphosphoglycerate levels. Finally, V˙O2max was lower in T1D-I compared with that in CON-I. No differences were observed between T1D-A and CON-A. Conclusions Poorly controlled patients displayed lower V˙O2max and blunted muscle deoxyhemoglobin increase. The latter supports the hypotheses of increase in O2 affinity induced by hemoglobin glycation and/or of a disturbed balance between nutritive and nonnutritive muscle blood flow. Furthermore, reduced exercise muscle blood volume in poorly controlled patients may warn clinicians of microvascular dysfunction occurring even before overt microangiopathy. PMID:24983346

High-Frequency Spin-Based Devices for Nanoscale Signal Processing

DTIC Science & Technology

2009-01-20

feedback on the devices in order to improve their spectral properties . Deliverable: Microwave signals without an Applied Field. We have successfully...additionally have the advantage of higher operating frequencies than the more conventional devices based on NiFe alloys. By combining several of...Output from a Co/Ni based STNO. Corresponds to approximately 20 nW, about 10 times larger than typical NiFe .device. 6 High-Frequency Spin-Based

Reflection Acoustic Microscopy for Micro-NDE.

DTIC Science & Technology

1983-02-01

WORDS (Coni, wu rere side. 14 It noeeeey And Idenify1 by block esife) Nondestructive Evaluation Acoustic Microscopy I Subsurface Imaging Pulsecio Cmrsin... subsurface imaging is presented and it is shown that with such lenses it is possible to obtain good focussing performance over a wide depth range...typically few millimeters at 50 MHz. A major problem in subsurface imaging derives from the large reflection obtained frnm the surface, and the small amount

Nanoconstriction spin-Hall oscillator with perpendicular magnetic anisotropy

NASA Astrophysics Data System (ADS)

Divinskiy, B.; Demidov, V. E.; Kozhanov, A.; Rinkevich, A. B.; Demokritov, S. O.; Urazhdin, S.

2017-07-01

We experimentally study spin-Hall nano-oscillators based on [Co/Ni] multilayers with perpendicular magnetic anisotropy. We show that these devices exhibit single-frequency auto-oscillations at current densities comparable to those for in-plane magnetized oscillators. The demonstrated oscillators exhibit large magnetization precession amplitudes, and their oscillation frequency is highly tunable by the electric current. These features make them promising for applications in high-speed integrated microwave circuits.

Snohomish Estuary Wetlands Study. Volume II. Basic Information and Evaluation

DTIC Science & Technology

1978-08-01

vegetation in these areas is of thrre major types : Coniferous trees , broadleaf deciluous trpee., ana shrubs. The coniferous trees are predominantly Sitka...in coniferous trees and also rest there when not hunting. The swamp habitat type is highly productive, generating abundant detr~i- tus. However, since...areas is of three major types : Coniferous trees , broadleaf deciduous trees , and shrubs. The coni- ferous trees are Sitka Spruce (Picea sitchensis

Electrosynthesis of magnetoresponsive microrobot for targeted drug delivery using calcium alginate.

PubMed

Chengzhi Hu; Riederer, Katharina; Klemmer, Michael; Pane, Salvador; Nelson, Bradley J

2016-08-01

Targeted drug delivery systems deliver drugs precisely to a specific targeted site inside the body, and can also release the drugs with controlled kinetics to prolong the efficacy of single dose administration. The advantageous properties of hydrogels make them attractive for use in the area of drug delivery. Calcium alginate is a pH sensitive hydrogel stable in acidic media and soluble in basic media. This enables the hydrogel to absorb and release aqueous solutions at certain ranges of pH values. By absorbing an aqueous solution containing a drug, an active drug release can be triggered at a specified range of pH value. In this paper, we combined calcium alginate with cobalt nickel (CoNi) in a cylindrical hybrid micro robot by electrodeposition. The designed microrobot can be wirelessly actuated with an external magnetic manipulation system and, hence, targeted to a specific location in the human body. At this specific location, characterized by its pH range, the absorbed drug will be released. Here, the fabrication steps of the specified microrobot are characterized, namely the production of a template on a silicon chip and the subsequent template-assisted electrodeposition of CoNi and alginate. Additionally, the dynamics of drug release of calcium alginate is studied.

Oxygen Evolution Activity of Co-Ni Nanochain Alloys: Promotion by Electron Injection.

PubMed

Yuan, Xiaotao; Riaz, Muhammad Sohail; Wang, Xin; Dong, Chenlong; Zhang, Zhe; Huang, Fuqiang

2018-03-12

Metal alloy nanoparticles have shown promising applications in electrocatalysis. However, the nanoparticles usually suffer from limited charge-transfer efficiency, which can be solved by preparing one-dimensional materials. Herein, Co-Ni alloy nanochains are prepared by a direct-current arc-discharge method. The nanochains, comprised of mutually coupled uniform nanospheres, can range up to several micrometers in size. When the alloy is exposed to air or under the electro-oxidation process, a metal-metal-oxide heterostructure is obtained. The alloy can inject electrons into the oxide, which makes it more suitable for electrocatalysis. The composition of the samples can be changed by varying the ratio of Ni/Co (i.e., Co, Co 7 Ni 3 , Co 5 Ni 5 , Co 3 Ni 7 , Ni) in the synthesis process. The nanochains show good oxygen evolution performance that correlates with the Ni/Co ratio. Co 7 Ni 3 demonstrates optimal activity with an onset point of 1.50 V vs. reversible hydrogen electrode (RHE) and overpotential of 350 mV at 10 mA cm -2 . The alloy nanochains also show excellent durability with 95.0 % current retention after a long-term test for 12 h. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanisms of radiation-induced segregation in CrFeCoNi-based single-phase concentrated solid solution alloys

DOE PAGES

He, Mo-Rigen; Wang, Shuai; Shi, Shi; ...

2016-12-31

Single-phase concentrated solid solution alloys have attracted wide interest due to their superior mechanical properties and enhanced radiation tolerance, which make them promising candidates for the structural applications in next-generation nuclear reactors. However, little has been understood about the intrinsic stability of their as-synthesized, high-entropy configurations against radiation damage. In this paper, we report the element segregation in CrFeCoNi, CrFeCoNiMn, and CrFeCoNiPd equiatomic alloys when subjected to 1250 kV electron irradiations at 400 °C up to a damage level of 1 displacement per atom. Cr/Fe/Mn/Pd can deplete and Co/Ni can accumulate at radiation-induced dislocation loops, while the actively segregating elementsmore » are alloy-specific. Moreover, electron-irradiated matrix of CrFeCoNiMn and CrFeCoNiPd shows L1 0 (NiMn)-type ordering decomposition and <001>-oriented spinodal decomposition between Co/Ni and Pd, respectively. Finally, these findings are rationalized based on the atomic size difference and enthalpy of mixing between the alloying elements, and identify a new important requirement to the design of radiation-tolerant alloys through modification of the composition.« less

Rate capability improvement of Co-Ni double hydroxides integrated in cathodically partially exfoliated graphite

NASA Astrophysics Data System (ADS)

Cai, Xiang; Song, Yu; Sun, Zhen; Guo, Di; Liu, Xiao-Xia

2017-10-01

In-situ growing of energy storage materials on graphene-based substrates/current collectors with low defect is a good way to boost electron transport and so enhance rate capability for the obtained electrode. Herein, high-quality graphene-like nanopetals are partially exfoliated from graphite foil (GF) through a facile and fast cathodic process. Three-dimensional porous structure is established for the afforded cathodically-exfoliated graphite foil (CEG), with many graphene-like nanopetals vertically anchoring on the graphite substrate. A hierarchical structure is constructed by the following electrochemical growth of Co-Ni double hydroxide nanopetals on the graphene atop CEG. The double hydroxide in the obtained electrode with the optimized Co2+/Ni2+ molar ratio, Co0.75Ni0.25(OH)2-CEG, displays much improved rate capability and so can deliver a high specific capacitance of 1460 F g-1 at an ultra-high current density of 100 A g-1. An asymmetric device is assembled by using Co0.75Ni0.25(OH)2-CEG as cathode, which demonstrates a high energy density of 31.6 Wh kg-1 at an ultra-high power density of 21.5 kW kg-1, showing the potential of the hierarchical composite electrode for high power application. The device also displays good stability, it can retain more than 90% of its capacitance after 10000 galvanostatic charge-discharge cycles.

Provision of tricuspid valve leaflets by septal papillary muscles in the right ventricle of human and other mammal hearts.

PubMed

Jezyk, Damian; Jerzemowski, Janusz; Grzybiak, Marek

2003-01-01

Leaflets of the tricuspid valve are provided by tendinous cords extending from the papillary muscles. The situation is complicated with the septal muscles, which generally occur in two groups, one as constant musculus coni arteriosi and the second as other variable septal muscles. We tested whether there is a variability in the provision of the tricuspid valve in different taxonomical groups of mammals. The material examined consisted of 299 hearts of mammals (Primates, Ungulata, Carnivora, Lagomorpha, Rodentia, Marsupialia). The musculus coni arteriosi in the majority of mammals provided only the front leaflet, but among Ungulata and Rodentia it provided simultaneously the front and septal leaflet. The other septal muscles provided the front, septal and even back leaflets. The following regularity was observed: in the hearts of Primates provision of the front leaflet and the front part of the septal leaflet predominated, among Ungulata the muscles provided the middle part of the septal leaflet, but among the other mammals the rest of the septal muscles provided, significantly, the back part of the septal leaflet. Such a provision was characteristic for predators, hares, rodents and marsupials. These circumstances may allow the conclusion to be drawn that there is a taxonomical dependence in the provision of the tricuspid valve in the hearts of the mammals under examination.

Iron-Induced Activation of Ordered Mesoporous Nickel Cobalt Oxide Electrocatalyst for the Oxygen Evolution Reaction.

PubMed

Deng, Xiaohui; Öztürk, Secil; Weidenthaler, Claudia; Tüysüz, Harun

2017-06-28

Herein, ordered mesoporous nickel cobalt oxides prepared by the nanocasting route are reported as highly active oxygen evolution reaction (OER) catalysts. By using the ordered mesoporous structure as a model system and afterward elevating the optimal catalysts composition, it is shown that, with a simple electrochemical activation step, the performance of nickel cobalt oxide can be significantly enhanced. The electrochemical impedance spectroscopy results indicated that charge transfer resistance increases for Co 3 O 4 spinel after an activation process, while this value drops for NiO and especially for CoNi mixed oxide significantly, which confirms the improvement of oxygen evolution kinetics. The catalyst with the optimal composition (Co/Ni 4/1) reaches a current density of 10 mA/cm 2 with an overpotential of a mere 336 mV and a Tafel slope of 36 mV/dec, outperforming benchmarked and other reported Ni/Co-based OER electrocatalysts. The catalyst also demonstrates outstanding durability for 14 h and maintained the ordered mesoporous structure. The cyclic voltammograms along with the electrochemical measurements in Fe-free KOH electrolyte suggest that the activity boost is attributed to the generation of surface Ni(OH) 2 species that incorporate Fe impurities from the electrolyte. The incorporation of Fe into the structure is also confirmed by inductively coupled plasma optical emission spectrometry.

MM III/Mk 12A Reentry Vehicle Carbon/Carbon Nosetip Production Program.

DTIC Science & Technology

1980-05-28

MI IlI/MIK 12A REENTRY VEHICLE CARBON/CARBON NOSETIP PRODUCTION PROGRAM CRITICAL ITEM CONI.<OL PLN 1.0 INTRODUCTION 1. 1 PURPOS’ The purpose of...the basis of its proven technological and pruduction capability in Fine-Weave Pierced Fabric (FWPF) Carbon/Carbocn Nosetips. Avco in turn has awarded...are inspected prior to the acceptanicc of the part. Each operator and/or inspector assig ;ned to do a specific task has all the required infornmation

Column Network Study for a Planar Array Used with an Unattended Radar

DTIC Science & Technology

1980-06-01

This will assist us In maintaining a current mailing list. Do not return this copy. Retain or destroy. UNCLASSIFIED SECURITY CLASSIFICATION OF THIS...0.nt from Controlling Office) IS. SECURITY CLASS. (o1 this report) SaetVŕ ’UDNCLASSIFIED IS.. DECL ASSI FIC ATI ON,’OWN GRADING t, / -/ ./N N...installation costs are being studied. "(Coni’d) DD I1JANp73 1473k EDITION OF I NOV 65 IS OBSOLETE UNCLASSIFIED SECURITY CLASSIFICATION OF THIS PAGE (When

Carbon nanofibers (CNFs) supported cobalt- nickel sulfide (CoNi2S4) nanoparticles hybrid anode for high performance lithium ion capacitor.

PubMed

Jagadale, Ajay; Zhou, Xuan; Blaisdell, Douglas; Yang, Sen

2018-01-25

Lithium ion capacitors possess an ability to bridge the gap between lithium ion battery and supercapacitor. The main concern of fabricating lithium ion capacitors is poor rate capability and cyclic stability of the anode material which uses sluggish faradaic reactions to store an electric charge. Herein, we have fabricated high performance hybrid anode material based on carbon nanofibers (CNFs) and cobalt-nickel sulfide (CoNi 2 S 4 ) nanoparticles via simple electrospinning and electrodeposition methods. Porous and high conducting CNF@CoNi 2 S 4 electrode acts as an expressway network for electronic and ionic diffusion during charging-discharging processes. The effect of anode to cathode mass ratio on the performance has been studied by fabricating lithium ion capacitors with different mass ratios. The surface controlled contribution of CNF@CoNi 2 S 4 electrode was 73% which demonstrates its excellent rate capability. Lithium ion capacitor fabricated with CNF@CoNi 2 S 4 to AC mass ratio of 1:2.6 showed excellent energy density of 85.4 Wh kg -1 with the power density of 150 W kg -1 . Also, even at the high power density of 15 kW kg -1 , the cell provided the energy density of 35 Wh kg -1 . This work offers a new strategy for designing high-performance hybrid anode with the combination of simple and cost effective approaches.

Thallium-rich pyrite ores from the Apuan Alps, Tuscany, Italy:constraints for their origin and environmental concerns

NASA Astrophysics Data System (ADS)

D'Orazio, Massimo; Biagioni, Cristian; Dini, Andrea; Vezzoni, Simone

2017-06-01

The southern sector of the Apuan Alps (AA) massif, Tuscany, Italy, is characterized by the occurrence of a series of baryte-pyrite-iron oxide orebodies whose Tl-rich nature was recognized only recently. The geochemistry of the pyrite ore was investigated through inductively coupled plasma mass spectrometry. In addition, lead isotope data for selected pyrite ores from AA were collected. Pyrite ores are characterized by a complex geochemistry, with high concentrations of Tl (up to 1100 μg/g) coupled with high As and Sb contents; the Co/Ni ratio is always <1. Geochemical data of pyrite and marcasite ore samples from other mining districts of Tuscany have been collected in order to compare them with those from the AA. These samples usually have very low Tl content (less than 2 μg/g) and high to very high Co/Ni and As/Sb ratios. Only some samples from the Sb-Hg ore deposits showed very high Tl concentrations (up to 3900 μg/g). Another difference is related to the lead isotope composition, with pyrite ores from AA markedly less radiogenic than those from the other deposits from Tuscany. Geochemical data of pyrite ores from AA give new insights on the genesis of the baryte-pyrite-iron oxide orebodies, relating their formation to low-temperature hydrothermal systems active during early Paleozoic; in addition, these data play a fundamental role in assessing the environmental impact of these deposits.

Alterations in Hepatic FGF21, Co-Regulated Genes, and Upstream Metabolic Genes in Response to Nutrition, Ketosis and Inflammation in Peripartal Holstein Cows

PubMed Central

Akbar, Haji; Batistel, Fernanda; Drackley, James K.; Loor, Juan J.

2015-01-01

In rodents, fibroblast growth factor 21 (FGF21) has emerged as a key metabolic regulator produced by liver. To gather preliminary data on the potential importance of FGF1, co-regulated genes, and upstream metabolic genes, we examined the hepatic mRNA expression in response to nutrition and inflammation in dairy cows. In experiment 1, induction of ketosis through feed restriction on d 5 postpartum upregulated FGF21, its co-receptor KLB, and PPARA but only elicited a numerical increase in serum FGF21 concentration. In experiment 2, cows in control (CON) or receiving 50 g/d of L-carnitine (C50) from -14 through 21 d had increased FGF21, PPARA, and NFIL3 on d 10 compared with d 2 postpartum. In contrast, compared with CON and C50, 100 g/d L-carnitine (C100) resulted in lower FGF21, KLB, ANGPTL4, and ARNTL expression on d 10. In experiment 3, cows were fed during the dry period either a higher-energy (OVE; 1.62 Mcal/kg DM) or lower-energy (CON; 1.34 Mcal/kg DM) diet and received 0 (OVE:N, CON:N) or 200 μg of LPS (OVE:Y, CON:Y) into the mammary gland at d 7 postpartum. For FGF21 mRNA expression in CON, the LPS challenge (CON:Y) prevented a decrease in expression between d 7 and 14 postpartum such that cows in CON:N had a 4-fold lower expression on d 14 compared with d 7. The inflammatory stimulus induced by LPS in CON:Y resulted in upregulation of PPARA on d 14 to a similar level as cows in OVE:N. In OVE:Y, expression of PPARA was lower than CON:N on d 7 and remained unchanged on d 14. On d 7, LPS led to a 4-fold greater serum FGF21 only in OVE but not in CON cows. In fact, OVE:Y reached the same serum FGF21 concentration as CON:N, suggesting a carryover effect of dietary energy level on signaling mechanisms within liver. Overall, results indicate that nutrition, ketosis, and inflammation during the peripartal period can alter hepatic FGF21, co-regulated genes, and upstream metabolic genes to various extents. The functional outcome of these changes merits further study, and in particular the mechanisms regulating transcription in response to changes in energy balance and feed intake. PMID:26451842

Alterations in Hepatic FGF21, Co-Regulated Genes, and Upstream Metabolic Genes in Response to Nutrition, Ketosis and Inflammation in Peripartal Holstein Cows.

PubMed

Akbar, Haji; Batistel, Fernanda; Drackley, James K; Loor, Juan J

2015-01-01

In rodents, fibroblast growth factor 21 (FGF21) has emerged as a key metabolic regulator produced by liver. To gather preliminary data on the potential importance of FGF1, co-regulated genes, and upstream metabolic genes, we examined the hepatic mRNA expression in response to nutrition and inflammation in dairy cows. In experiment 1, induction of ketosis through feed restriction on d 5 postpartum upregulated FGF21, its co-receptor KLB, and PPARA but only elicited a numerical increase in serum FGF21 concentration. In experiment 2, cows in control (CON) or receiving 50 g/d of L-carnitine (C50) from -14 through 21 d had increased FGF21, PPARA, and NFIL3 on d 10 compared with d 2 postpartum. In contrast, compared with CON and C50, 100 g/d L-carnitine (C100) resulted in lower FGF21, KLB, ANGPTL4, and ARNTL expression on d 10. In experiment 3, cows were fed during the dry period either a higher-energy (OVE; 1.62 Mcal/kg DM) or lower-energy (CON; 1.34 Mcal/kg DM) diet and received 0 (OVE:N, CON:N) or 200 μg of LPS (OVE:Y, CON:Y) into the mammary gland at d 7 postpartum. For FGF21 mRNA expression in CON, the LPS challenge (CON:Y) prevented a decrease in expression between d 7 and 14 postpartum such that cows in CON:N had a 4-fold lower expression on d 14 compared with d 7. The inflammatory stimulus induced by LPS in CON:Y resulted in upregulation of PPARA on d 14 to a similar level as cows in OVE:N. In OVE:Y, expression of PPARA was lower than CON:N on d 7 and remained unchanged on d 14. On d 7, LPS led to a 4-fold greater serum FGF21 only in OVE but not in CON cows. In fact, OVE:Y reached the same serum FGF21 concentration as CON:N, suggesting a carryover effect of dietary energy level on signaling mechanisms within liver. Overall, results indicate that nutrition, ketosis, and inflammation during the peripartal period can alter hepatic FGF21, co-regulated genes, and upstream metabolic genes to various extents. The functional outcome of these changes merits further study, and in particular the mechanisms regulating transcription in response to changes in energy balance and feed intake.

Ada (trade name) Compiler Validation Summary Report: Rational Environment, Version A.2.0.6 for Rational R1000.

DTIC Science & Technology

1985-05-24

RD-Ali57 830 ADA (TRADE NAME) COMPILER VALIDATION SUMMARY REPORT: 1/ RATIONAL ENVIRONMENT VERSION R296 FOR RATIONAL Ri888 (U) SOFTECH INC FAIRBORN OH...USoCPY WSSOS.UTM iTS GWAT % : 4 AVF Control Number: AVF-VSR-09.0585 0 IAda Compiler Validation Summary Report: Rational Environment Version A.2.0.6 For...1985 to May 1986 Environment Version A.2-0.6 For Rational RlOOO (Final) ______________ S. PLNOPftaiJSw mO. ftLOW@N WuCU ). aulwtar111. CONiTRACT 00

Naval Nuclear Arms Reduction - Fixing the US Navy’s Achilles’ Heel

DTIC Science & Technology

1990-06-12

Kashin ( 4 1 3 6 ) 12 Kashin (4/36) 8 Kanin (2/16) 8 SAM Kotlin (2/16) N u c l e a r or Cony 3 K i e v ( 4 / 7 2 ) I Hod K i e v (4172) 2...8 SAM Kotlin (2/16) 3 K iev (4172) 1 Hod K iev (4172) 2 Moskva (4 /44) 7 Kara (4 /72) I0 K res ta I I (4 /72) 3+ K i r o v ( 1 2 / 9 6

Control of the Diameter and Chiral Angle Distributions during Production of Single-wall Carbon Nanotubes

NASA Technical Reports Server (NTRS)

Nikolaev, Pavel; Holmes, William; Sosa, Edward; Boul, Peter; Arepalli, Sivaram; Yowell, Leonard

2008-01-01

Many applications of single wall carbon nanotubes (SWCNT), especially in microelectronics, will benefit from use of certain (n,m) nanotube types (metallic, small gap semiconductor, etc.). However, as produced SWCNT samples are polydispersed, with many (n,m) types present and typical approximate 1:2 metal/semiconductor ratio. It has been recognized that production of SWCNTs with narrow 'tube type populations' is beneficial for their use in applications, as well as for the subsequent sorting efforts. In the present work, SWCNTs were produced by a pulsed laser vaporization (PLV) technique. The nanotube type populations were studied with respect to the production temperature with two catalyst compositions: Co/Ni and Rh/Pd. The nanotube type populations were measured via photoluminescence, UV-Vis-NIR absorption and Raman spectroscopy. It was found that in the case of Co/Ni catalyst, decreased production temperature leads to smaller average diameter, exceptionally narrow diameter distribution, and strong preference toward (8,7) nanotubes. The other nanotubes present are distributed evenly in the 7-30 deg chiral angle range. In the case of Rh/Pd catalyst, a decrease in the temperature leads to a small decrease in the average diameter, with the chiral angle distribution skewed towards 30 o and a preference toward (7,6), (8,6) and (8,7) nanotubes. However, the diameter distribution remains rather broad. These results demonstrate that PLV production technique can provide at least partial control over the nanotube (n,m) populations. In addition, these results have implications for the understanding the nanotube nucleation mechanism in the laser oven.

Electrical resistivity of Co-Ni-Pd and Co-Pd alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jen, S.U.; Chen, T.P.; Chang, S.A.

1991-11-15

Three series of ferromagnetic alloys have been made: Co{sub 100{minus}{ital x}}Pd{sub {ital x}}, Co{sub 25}Ni{sub 75{minus}{ital y}}Pd{sub {ital y}} and Co{sub 5{minus}{ital z}}Ni{sub {ital z}}Pd{sub 95}. The electrical resistivity {rho} of these alloys was measured from 4 to 300 K. Their high field ({ital H}{gt}2 T) susceptibility {chi}{sub HF} was obtained with superconducting quantum interference device measurements at 5 K. Comparing the residual resistivity {rho}{sub 0} of Co-Ni and Co-Pd, it is found that the spin-up resistivity {rho}{sub {up arrow}} of Co-Ni follows the Nordheim's rule, while that of Co-Pd peaks at {ital x}=85. This indicates the spin-up {ital d}more » band of Co-Pd is not full for all the {ital x} values. Also, {chi}{sub HF} data reveal the same tendency of the spin-up band. Based on the deviation from Matthiessen's rule of the two-current model, we estimate {alpha}={rho}{sub 0{down arrow}} /{rho}{sub 0{up arrow}}{congruent}2 for the dilute {ital PdCo} alloy, where {rho}{sub 0}={rho}{sub 0{down arrow}} {rho}{sub 0{up arrow}}/({rho}{sub 0{up arrow}}+{rho}{sub 0{down arrow}} ), from the residual resistivity of the ternary Co{sub 5{minus}{ital z}}Ni{sub {ital z}}Pd{sub 95} alloy and from the temperature dependence of {rho}({ital T}) of the binary Co{sub 5}Pd{sub 95} alloy« less

Electronic and Solid State Sciences. Program Summary, FY 1979.

DTIC Science & Technology

1979-01-01

tcl I amle Y -nenLr lt, 5m15 ho i’rmwn ain I teasiurir<, aLn-i the slcow coni- 24 version ,C )rthohydro,.en to parahy,.iroo:en permits u i que...discrete devices, and in new oscillator circuits in which the turn-on delay of the CFT is what determines the frequency of oscillation. Recent Publications...Hialmarson, Ph.D. Thesis , University of Illinois (1979). 4. "N Trap in the Semiconductor Alloys GaAsl-xPx and AlxGalw.As", D.J. Wofford, J.D. Dow, W.Y

Design and Implementation of Multi-Input Adaptive Signal Extractions.

DTIC Science & Technology

1980-07-31

8 𔃺 - I I 2 l ~lI II~ lliiII 111111L25 I )1.4 jg16 MICROCOPY RESOLUTION TEST CHART NA110NAt ftl Ali I TANtDAN[1A I "I A U*iI L ~ I0SGALADIAEPOESN A...NUMBER 4. TITLE (and Subtitle) S. TYPE OF REPORT & PERIOD COVERED _EIGN AND LLEMF TATICN OF XJLTI- NPUr A j n7T 1 Ax L )DAPTIVE NLEXRACTIONS 6. ERFORMING...conventional adaptive filtering and noise cancelling coni gurIFORM l / DD I JAN 73 1473 EDITION OF I NOV 65 IS OBSOLETE UNCLASSIFIED SECURITY

Perpendicular Magnetic Anisotropy in Ultrathin Co/Ni Multilayer Films Studies with Ferromagnetic Resonance and Magnetic X-Ray Microspectroscopy

DTIC Science & Technology

2012-06-28

a collection of information if it does not display a currently valid OMB control number . PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. a...REPORT TYPE New Reprint 17. LIMITATION OF ABSTRACT UU 15. NUMBER OF PAGES 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 5c. PROGRAM...ELEMENT NUMBER 5b. GRANT NUMBER 5a. CONTRACT NUMBER W911NF-08-1-0317 611103 Form Approved OMB NO. 0704-0188 54223-MS-MUR.32 11. SPONSOR/MONITOR’S

Characterization and corrosion behaviour of CoNi alloys obtained by mechanical alloying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olvera, S.; Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Química-Física Aplicada, 28049 Madrid; Sánchez-Marcos, J.

2014-07-01

CoNi alloys including Co{sub 30}Ni{sub 70}, Co{sub 50}Ni{sub 50} and Co{sub 70}Ni{sub 30} were prepared via mechanical alloying using Co and Ni powders. The crystallinity and short-range order were studied using X-ray diffraction and X-ray absorption spectroscopy. The results show that the milling process increases the number of vacancies, especially around the Co atoms, while the milling time decreases the crystalline size and enhances the crystallinity. X-ray photoelectron spectroscopy was used to characterise the chemical composition of the samples surface. The magnetic properties were analysed using zero-field cooling, field cooling and a magnetic hysteresis loops. The magnetic saturation moment ismore » approximately 1.05 μ{sub B}/atom; this value decreases with the mechanical alloying time, and it is proportional to the cobalt concentration. The polarization and impedance curves in different media (NaCl, H{sub 2}SO{sub 4} and NaOH) showed similar corrosion resistance values. The corrosion resistance increased in the order NaCl, H{sub 2}SO{sub 4} and NaOH. A good passivation layer was formed in NaOH due to the cobalt and nickel oxides on the particle surfaces. - Highlights: • Ni{sub x}Co{sub 100-x} alloys were synthesized by mechanical alloying • Milling time decrease size and enhances crystallinity. • Oxygen is not present in a significant percentage in bulk but is detected on the surface. • Magnetic saturation moment is 1.05 mB/atom and decrease with mechanical allowing time • Corrosion resistance is higher in NaOH than in NaCl or HCl solutions.« less

Handbook for Forecasters in the Mediterranean; Weather Phenomena of the Mediterranean Basin; Part 1. General Description of the Meteorological Processes

DTIC Science & Technology

1975-11-01

of its existence was coni. sidered. The frequencies were counted In boxes 5° latitude in length and of the varying widths listed in Table 111-1-3...in Perpignan (sta. no. 07747); cierzo in Spain; cers in the Pyrenees, etc. South of Mont Ventcjx (sta. no. 07585) a similar wind is named bise. A local...de Cristo Mountains h = 1.1 km in Colorado X = 10 km k = km- -1 UI = 20 m sec -l w0 2.7 m sec According to Figure V-B-2, one could expect light to

Large spin-orbit torques in Pt/Co-Ni/W heterostructures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Jiawei; Qiu, Xuepeng; Legrand, William

2016-07-25

The spin orbit torques (SOTs) in perpendicularly magnetized Co-Ni multilayers sandwiched between two heavy metals (HM) have been studied. By exploring various HM materials, we show an efficient enhancement or cancellation of the total SOT, depending on the combination of the two HM materials. The maximum SOT effective field is obtained in Pt/Co-Ni/W heterostructures. We also model our double HM system and show that the effective spin Hall angle has a peak value at certain HM thicknesses. Measuring the SOT in Pt/Co-Ni/W for various W thicknesses confirms an effective spin Hall angle up to 0.45 in our double HM system.

Development of a Cool Propellant for the 3 in./50 Caliber Gun. Development of a Cool Propellant for the 3 in./70 Caliber Gun. Development of Ignition Systems for the Cool Propellant Charges. Ballistic Test of Cool Propellants EX-6735, EX-6721 and IHPB-S-83C

DTIC Science & Technology

1951-06-09

HHMKHtffivfädMK fiösafe^.^., " -."- ; ji- ^ vrf •»£,. gyyrarfwaMHf^» i~ "& I •^ is\\!"* .!•,’•• .-••nj’’ ’ r.’ U St"-/s...34. <•-.-"- A.tttu Tseiinical Lite ,fü^-=^-<^ss> >,, -7 > ’" Commanding General, F^ank^ord^Arjsenal ._ Bridge and faCony Stree’t-s^.r^qr^—--- - Z

Current induced perpendicular-magnetic-anisotropy racetrack memory with magnetic field assistance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Y.; Klein, J.-O.; Chappert, C.

2014-01-20

High current density is indispensable to shift domain walls (DWs) in magnetic nanowires, which limits the using of racetrack memory (RM) for low power and high density purposes. In this paper, we present perpendicular-magnetic-anisotropy (PMA) Co/Ni RM with global magnetic field assistance, which lowers the current density for DW motion. By using a compact model of PMA RM and 40 nm design kit, we perform mixed simulation to validate the functionality of this structure and analyze its density potential. Stochastic DW motion behavior has been taken into account and statistical Monte-Carlo simulations are carried out to evaluate its reliability performance.

In situ synthesis of semiconducting single-walled carbon nanotubes by modified arc discharging method

NASA Astrophysics Data System (ADS)

Zhao, Tingkai; Ji, Xianglin; Jin, Wenbo; Yang, Wenbo; Zhao, Xing; Dang, Alei; Li, Hao; Li, Tiehu

2017-02-01

Semiconducting single-walled carbon nanotubes (s-SWCNTs) were in situ synthesized by a temperature-controlled arc discharging furnace with DC electric field using Co-Ni alloy powder as catalyst in helium gas. The microstructures of s-SWCNTs were characterized using high-resolution transmission electron microscopy, electron diffraction, and Raman spectrometry apparatus. The experimental results indicated that the best voltage value in DC electric field is 54 V, and the environmental temperature of the reaction chamber is 600 °C. The mean diameter of s-SWCNTs was estimated about 1.3 nm. The chiral vector ( n, m) of s-SWCNTs was calculated to be (10, 10) type according to the electron diffraction patterns.

Revealing the synergetic effects in Ni nanoparticle-carbon nanotube hybrids by scanning transmission X-ray microscopy and their application in the hydrolysis of ammonia borane

NASA Astrophysics Data System (ADS)

Zhao, Guanqi; Zhong, Jun; Wang, Jian; Sham, Tsun-Kong; Sun, Xuhui; Lee, Shuit-Tong

2015-05-01

The hybrids of carbon nanotubes (CNTs) and the supported Ni nanoparticles (NPs) have been studied by scanning transmission X-ray microscopy (STXM) and tested by the hydrolysis reaction of ammonia borane (AB, NH3BH3). Data clearly showed the existence of a strong interaction between Ni NPs and thin CNTs (C-O-Ni bonds), which favored the tunable (buffer) electronic structure of Ni NPs facilitating the catalytic process. The hydrolysis process of AB confirmed the hypothesis that the hybrids with a strong interfacial interaction would show superior catalytic performance, while the hybrids with a weak interfacial interaction show poor performance. Our results provide a wealth of detailed information regarding the electronic structure of the NP-CNT hybrids and provide guidance towards the rational design of high-performance catalysts for energy applications.The hybrids of carbon nanotubes (CNTs) and the supported Ni nanoparticles (NPs) have been studied by scanning transmission X-ray microscopy (STXM) and tested by the hydrolysis reaction of ammonia borane (AB, NH3BH3). Data clearly showed the existence of a strong interaction between Ni NPs and thin CNTs (C-O-Ni bonds), which favored the tunable (buffer) electronic structure of Ni NPs facilitating the catalytic process. The hydrolysis process of AB confirmed the hypothesis that the hybrids with a strong interfacial interaction would show superior catalytic performance, while the hybrids with a weak interfacial interaction show poor performance. Our results provide a wealth of detailed information regarding the electronic structure of the NP-CNT hybrids and provide guidance towards the rational design of high-performance catalysts for energy applications. Electronic supplementary information (ESI) available: Magnified TEM images, high resolution TEM images and the particle size distributions of the samples, the STXM results of a thick tube at different positions, XPS results, stability test. See DOI: 10.1039/c5nr01168j

Trace Element Geochemistry of Magnetite and Accesory Phases from El Romeral Iron Oxide-Apatite Deposit, Northern Chile

NASA Astrophysics Data System (ADS)

Barra, F.; Rojas, P.; Reich, M.; Deditius, A.; Simon, A. C.

2017-12-01

Iron oxide-apatite (IOA) or "Kiruna-type" deposits are an important source of Fe, P, REE, among other essential elements for society. Three main hypotheses have been proposed to explain the genesis of these controversial deposits, which invoke liquid immiscibility, hydrothermal replacement or a magmatic-hydrothermal origin driven by flotation of magnetite-bubble pairs. Here we focus on the El Romeral, one of the largest IOA deposits located in the southernmost part of the Cretaceous Chilean Iron Belt. We combined SEM observations and EMPA analyses of magnetite, actinolite, pyrite, and apatite, with micro-Raman determinations of mineral inclusions within magnetite grains. Two textural types of magnetite were identified at El Romeral: (i) inclusion-rich magnetite (Mag I), and (ii) inclusion-poor magnetite (Mag II) that are commonly surrounding the inclusion-rich Mag I grains. Mag I is characterized by high V ( 2500-2800 ppm) and Ti (300-1000 ppm) contents with high-temperature mineral inclusions such as ilmenite, Ti-pargasite and clinochlore at depth, and quartz and phlogopite inclusions in shallower samples. These characteristics are consistent with a magmatic origin for Mag I. Inclusion-poor magnetite (Mag II) have high V (2400-2600 ppm) and lower Ti (70-200 ppm) contents than Mag I, which point to chemical changes of the mineralizing fluid(s). An increase in thermal gradient with depth is evidenced by the presence of high-temperature (low #Fe) actinolite, as well as F-rich apatite and pyrite with high Co:Ni (>1) in the deep zones. In contrast, lower Co:Ni ratios (<0.5) in pyrite and higher Cl contents in OH-rich apatite are detected in samples from shallower levels. This vertical chemical variation supports a magmatic-hydrothermal origin for the El Romeral deposit, and point to compositional changes driven by decompression of a magnetite-fluid suspension.

The case for metamorphic base metal mineralization: pyrite chemical, Cu and S isotope data from the Cu-Zn deposit at Kupferberg in Bavaria, Germany

NASA Astrophysics Data System (ADS)

Höhn, S.; Frimmel, H. E.; Debaille, V.; Pašava, J.; Kuulmann, L.; Debouge, W.

2017-12-01

The stratiform Cu-Zn sulfide deposit at Kupferberg in Germany represents Bavaria's largest historic base metal producer. The deposit is hosted by Early Paleozoic volcano-sedimentary strata at the margin of a high-grade allochthonous metamorphic complex. The present paper reports on the first Cu and S isotope data as well as trace element analyses of pyrite from this unusual deposit. The new data point to syn-orogenic mineralization that was driven by metamorphic fluids during nappe emplacement. Primary Cu ore occurs as texturally late chalcopyrite within stratiform laminated pyrite in black shale in two different tectonostratigraphic units of very low and low metamorphic grade, respectively, that were juxtaposed during the Variscan orogeny. Trace element contents of different pyrite types suggest the presence of at least one hydrothermal pyrite generation (mean Co/Ni = 35), with the other pyrite types being syn-sedimentary/early diagenetic (mean Co/Ni = 3.7). Copper isotope analyses yielded a narrow δ65Cu range of -0.26 to 0.36‰ for all ore types suggesting a hypogene origin for the principal chalcopyrite mineralization. The ore lenses in the two different tectonostratigraphic units differ with regard to their δ34S values, but little difference exists between poorly and strongly mineralized domains within a given locality. A genetic model is proposed in which syn-sedimentary/early diagenetic pyrite with subordinate chalcopyrite and sphalerite formed in black shale beds in the two different stratigraphic units, followed by late-tectonic strata-internal, hydrothermal mobilization of Fe, Cu, and Zn during syn-orogenic thrusting, which concentrated especially Cu to ore grade. In agreement with this model, Cu distribution in stream sediments in this region shows distinct enrichments bound to the margin of the allochthonous complex. Thus, Kupferberg can be considered a rare example of a syn-orogenic Cu deposit with the Cu probably being derived from syn-sedimentary/early diagenetic pyrite contained in Early Paleozoic shale units.

Magnetic x-ray dichroism in ultrathin epitaxial films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tobin, J.G.; Goodman, K.W.; Cummins, T.R.

1997-04-01

The authors have used Magnetic X-ray Linear Dichroism (MXLD) and Magnetic X-ray Circular Dichroism (MXCD) to study the magnetic properties of epitaxial overlayers in an elementally specific fashion. Both MXLD and MXCD Photoelectron Spectroscopy were performed in a high resolution mode at the Spectromicroscopy Facility of the ALS. Circular Polarization was obtained via the utilization of a novel phase retarder (soft x-ray quarter wave plate) based upon transmission through a multilayer film. The samples were low temperature Fe overlayers, magnetic alloy films of NiFe and CoNi, and Gd grown on Y. The authors results include a direct comparison of highmore » resolution angle resolved Photoelectron Spectroscopy performed in MXLD and MXCD modes as well as structural studies with photoelectron diffraction.« less

Comparative study of synthesis, structural and magnetic properties of Cu2+ substituted Co-Ni, Co-Zn and Co-Mg nano ferrites

NASA Astrophysics Data System (ADS)

Ramakrishna, A.; Murali, N.; Margarette, S. J.; Samatha, K.; Veeraiah, V.

2018-02-01

Mixed ferrites of the form Co0.5M0.1Cu0.4Fe2O4 (M = Ni, Zn and Mg) have been synthesized using the sol-gel auto combustion technique. Structural analyses are carried out using powder X-ray diffraction to idntify pure ferrite phases. SEM analysis revealed clear crystal morphology with relatively uniform grain sizes with polygonal structures. The FT-IR studies also confirm the bond formation and cation vibrations at low (365-392 cm-1) and high (579-587 cm-1) bands that correspond to the tetrahedral and octahedral sites, respectively. The magnetic properties studied through vibrating sample magnetometer showed that the Ni substituted sample has more magnetic character by exhibiting the highest saturation magnetization.

Mineralogy and trace element geochemistry of the Co- and Cu-bearing sulfides from the Shilu Fe-Co-Cu ore district in Hainan Province of South China

NASA Astrophysics Data System (ADS)

Wang, Zhilin; Xu, Deru; Zhang, Zhaochong; Zou, Fenghui; Wang, Li; Yu, Liangliang; Hu, Mingyue

2015-12-01

Hosted within the metamorphosed, neritic siliciclastic rocks and sedimentary carbonates of the Proterozoic Shilu Group, the Shilu Fe-Co-Cu ore district in Hainan Province of South China comprises the upper Fe- and the lower Co-Cu ore layers. Combined with the field observation, the mineralogical and geochemical studies of sulfides using electron microprobe and laser ablation ICP-MS analyses recognized three types of Co-Cu ores. Type I is represented by massive ores and mainly comprises the first generation of pyrite (PyI) which occurred either as recrystallized, subhedral to euhedral microcrystal aggregates (PyIa) or as elongated, fine-grained euhedral grains (PyIb) with an orientated alignment parallel to S1 foliation. Type II is banded, disseminated and brecciated ores, and composed of the second generation of pyrite (PyII) which displays internal rhythmic growth zoning, the first generations of chalcopyrite (CcpI) and pyrrhotite (PoI), and associated Co-(Ni)-(As)-sulfide minerals. Type III occurring as veins or veinlets mainly consists of the third generation of pyrite (PyIII) and the second generations of chalcopyrite (CcpII) and pyrrhotite (PoII), of which PyIII appears as subhedral to euhedrall grains or as rims of composite pyrite. The moderate Co and As, and high Ni contents as well as the low Co/Ni ratios (∼2-5) in PyI indicate a sedimentary-metamorphic origin for Type I ores. The higher Co, Ni and As concentrations in PyIb relative to PyIa likely was related to an inhomogeneous deformation-metamorphism. The highest Co (av. 51,195 ppm) in PyII and Ni (av. 3374 ppm) in PoI most likely were linked to the preferred incorporation of Co into pyrite and Ni into pyrrhotite. Combined with the high Ag concentrations in CcpI (av. 266 ppm) and PyII (av. 13.32 ppm), the high Co/Ni ratios in PyII (av. 1241) suggest the derivation of Type II ores from a Co-Cu-Ni-Ag-rich hydrothermal fluid. Further, up to 9 wt.% Co concentrations in PyII show a temperature condition of 310-400 °C. In contrast, the depletion of trace elements in CcpII and PyIII, and the lower Co/Ni ratios (av. 46) in PyIII suggest a Co-poor but Cu-bearing hydrothermal fluid for origin of Type III ores. The complex texture and chemical composition of sulfides combined with previous work confirm a four-stage metallogenesis for the Shilu Co-Cu ores. From early to late, these include: (1) the ca. 1075-880 Ma deposition of the primary Co-Cu ore source beds which most likely were derived from submarine, metalliferous hydrothermal fluids, (2) the syn-structural metamorphism which led to Type I ores due to the South China Caledonian Orogeny, (3) the first stage of hydrothermalism which produced Type II ores and most likely was associated with Indosinian magmatism, and (4) the second stage of hydrothermalism which yielded Type III ores and likely was related to Yanshanian magmatism. The first stage of hydrothermalism was considered to be significant for the Co-Cu enrichment. The Shilu Co-Cu ores thus are better attributed to a BIF origin, but greatly reworked and enriched by late structural deformation and hydrothermal activities.

Prime Contract Awards Alphabetically by Contractor, By State or Country, and Place, FY 84. Part 6. (Holcomb Construction - Kwickstok, Inc).

DTIC Science & Technology

1984-01-01

EEEEEEllllhUEEEEE.l EhlllhhEEEEEEEEElllll mEEEEEEEllllllhlllhEil .L.- a ji i~ liliiii m °’. MICROCOPY RESOLUTION TEST C4’MT NATIONAL BUREAU OF STANDAIRDS.1963-A...00- -0017 - If) NO .0 V 0--0 0- 0 (of, CD -- N N - 0 -- f- N 0)- -N a) CD CONI * 0 V1000N 00 NY 00 000- 00 Mo00 000q m IT 0- x 4c U 0Y - m NN CY...W z M E 0aI ɜ < 4c 4c40 C.040000 I 0 0 0 00 ~0 1010 00 000000.4CD 00 4 0 0 0 0 40 0000 .000.l 00 0 0 0 00 0 00 00 000000 0o MOM00 NN 0) Nu (A

Metal Precursors and Reduction in Renazzo Chondrules

NASA Astrophysics Data System (ADS)

Zanda, B.; Hewins, R. H.; Bourot-Denise, M.

1993-07-01

The positive Co-Ni correlation and Cr, P contents of metal in CR chondrites have generally been taken to indicate their primitive nature, probably inherited from condensation [1,2]. Si in the metal of primitive chondrites has also been reported and interpreted as a condensation heritage [3,4]. However, Cr, P, and Si (dissolved or in the form of inclusions) in metal of any CR chondrule generally fall within a +-10% range, though large interchondrule variations exist [5]. We have shown that Cr and Si in metal are in equilibrium with Fo and En in silicates, due to the reducing conditions that prevailed during chondrule formation [6]. In the present paper, we show that the Co-Ni trend was also established during chondrule formation out of heterogeneous precursor material with a variable Co/Ni ratio. Chondrules in Renazzo are classified as highly molten (HM), in which metal has been expelled to form a mantle outside the chondrule, medium molten (MM), with metal inside and at the periphery, and with evidence for grain coalescence, and little melted (LM), in which metal is only present in the form of small blebs dispersed among the silicates. In HM chondrules, Ni and Co concentrations are extremely homogeneous, comparatively low and in the cosmic ratio. In LM chondrules, quite the opposite: Ni and Co spread over a large range and the amount of scatter increases with decreasing degree of melting of the chondrule. In addition, they do not correlate along the cosmic ratio, but show a negative correlation if any. This heterogeneity is present not only from grain to grain in these chondrules, but also in individual metal grains. Such a heterogeneity is also exhibited in Cr and P abundances that span a much larger range than the +-10% found in the other chondrules. These results indicate that chondrule formation is responsible for the homogenization of Co and Ni contents of metal grains through coalescence and mixing. The less melted objects give an idea of the nature of metal in chondrule precursors, extremely heterogeneous and fine grained (each small heterogeneous metal bleb might be the result of partial melting of one or of coalescence and imperfect mixing of a few such grains). Co and Ni in these individual grains were not in the cosmic ratio, but wide sampling of dust in each chondrule precursor insured that this ratio was attained after mixing and homogenization, as seen in HM chondrule metal grains and from mean values of Co and Ni in LM chondrules. In MM chondrules, scatter of Ni and Co data are, as expected, intermediate between those of HM and LM chondrules, but Co and Ni are close to the cosmic ratio. The scatter is mostly due to addition of variable quantities of iron in the reduction during chondrule formation, which is responsible for Cr and Si integration into metal. Further evidence of such a process can be found in the less molten of these objects, in which metal grain coalescence is limited and peripheral grains are still different from inside grains. In these cases, Co and Ni distributions are clearly bimodal, high in inside grains, low in peripheral grains. Co/Ni in these two populations are somewhat scattered around the cosmic ratio, but their means (Ni: 7.75 = +- 0.24, Co: 0.36 +- 0.04, and Ni: 4.39 +- 0.34, Co: 0.23 +- 0.02, e.g., in the case of chondrule AL1) are very close to the cosmic ratio. This is in good agreement with the low values found in the homogeneous mantle grains of HM chondrules and, as noted by Lee et al. [7], indicates that the reducing agent was external to the chondrule. Cr abundances of these peripheral metal grains, however, match Cr abundances of the interior ones in these chondrules. This indicates that the redox state of all these grains was attained simultaneously and controlled by equilibrium with chondrule silicates. Slightly more extensive reduction of the latter close to the chondrule surface that added more Fe to peripheral metal grains resulted in only a minor variation of the Cr partition coefficient: it consequently also induced Cr addition, the Cr/Fe ratio varying only marginally. Therefore, we believe unlike [7] the process to have been nebular, and the reducing agent the nebular gas, although equilibrium with this gas was clearly not attained. References: [1] Weisberg M. K. et al. (1993) GCA, 57, 1567-1586. [2] Grossman L. and Olsen E. (1974) GCA, 38, 173-187. [3] Grossman L., et al. (1979) Science, 206, 449-451. [4] Rambaldi E. R. et al. (1980) Nature, 287; Nature, 293, 558-561. [5] Zanda B. et al. (1991) LPSC XXII, 1543-1544. [6] Hewins R. H. and Zanda B. (1992) Meteoritics, 27, 233. [7] Lee M. S. et al. (1992) GCA, 56, 2521-2533.

Effects of grain size on the properties of bulk nanocrystalline Co-Ni alloys

NASA Astrophysics Data System (ADS)

Qiao, Gui-Ying; Xiao, Fu-Ren

2017-08-01

Bulk nanocrystalline Co78Ni22 alloys with grain size ranging from 5 nm to 35 nm were prepared by high-speed jet electrodeposition (HSJED) and annealing. Microhardness and magnetic properties of these alloys were investigated by microhardness tester and vibrating sample magnetometer. Effects of grain size on these characteristics were also discussed. Results show that the microhardness of nanocrystalline Co78Ni22 alloys increases following a d -1/2-power law with decreasing grain size d. This phenomenon fits the Hall-Petch law when the grain size ranges from 5 nm to 35 nm. However, coercivity H c increases following a 1/d-power law with increasing grain size when the grain size ranges from 5 nm to 15.9 nm. Coercivity H c decreases again for grain sizes above 16.6 nm according to the d 6-power law.

Synthesis And Characterization Of Reduced Size Ferrite Reinforced Polymer Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borah, Subasit; Bhattacharyya, Nidhi S.

2008-04-24

Small sized Co{sub 1-x}Ni{sub x}Fe{sub 2}O{sub 4} ferrite particles are synthesized by chemical route. The precursor materials are annealed at 400, 600 and 800 C. The crystallographic structure and phases of the samples are characterized by X-ray diffraction (XRD). The annealed ferrite samples crystallized into cubic spinel structure. Transmission Electron Microscopy (TEM) micrographs show that the average particle size of the samples are <20 nm. Particulate magneto-polymer composite materials are fabricated by reinforcing low density polyethylene (LDPE) matrix with the ferrite samples. The B-H loop study conducted at 10 kHz on the toroid shaped composite samples shows reduction in magneticmore » losses with decrease in size of the filler sample. Magnetic losses are detrimental for applications of ferrite at high powers. The reduction in magnetic loss shows a possible application of Co-Ni ferrites at high microwave power levels.« less

Excess velocity of magnetic domain walls close to the depinning field

NASA Astrophysics Data System (ADS)

Caballero, Nirvana B.; Fernández Aguirre, Iván; Albornoz, Lucas J.; Kolton, Alejandro B.; Rojas-Sánchez, Juan Carlos; Collin, Sophie; George, Jean Marie; Diaz Pardo, Rebeca; Jeudy, Vincent; Bustingorry, Sebastian; Curiale, Javier

2017-12-01

Magnetic field driven domain wall velocities in [Co/Ni] based multilayers thin films have been measured using polar magneto-optic Kerr effect microscopy. The low field results are shown to be consistent with the universal creep regime of domain wall motion, characterized by a stretched exponential growth of the velocity with the inverse of the applied field. Approaching the depinning field from below results in an unexpected excess velocity with respect to the creep law. We analyze these results using scaling theory to show that this speeding up of domain wall motion can be interpreted as due to the increase of the size of the deterministic relaxation close to the depinning transition. We propose a phenomenological model to accurately fit the observed excess velocity and to obtain characteristic values for the depinning field Hd, the depinning temperature Td, and the characteristic velocity scale v0 for each sample.

Revealing the synergetic effects in Ni nanoparticle-carbon nanotube hybrids by scanning transmission X-ray microscopy and their application in the hydrolysis of ammonia borane.

PubMed

Zhao, Guanqi; Zhong, Jun; Wang, Jian; Sham, Tsun-Kong; Sun, Xuhui; Lee, Shuit-Tong

2015-06-07

The hybrids of carbon nanotubes (CNTs) and the supported Ni nanoparticles (NPs) have been studied by scanning transmission X-ray microscopy (STXM) and tested by the hydrolysis reaction of ammonia borane (AB, NH3BH3). Data clearly showed the existence of a strong interaction between Ni NPs and thin CNTs (C-O-Ni bonds), which favored the tunable (buffer) electronic structure of Ni NPs facilitating the catalytic process. The hydrolysis process of AB confirmed the hypothesis that the hybrids with a strong interfacial interaction would show superior catalytic performance, while the hybrids with a weak interfacial interaction show poor performance. Our results provide a wealth of detailed information regarding the electronic structure of the NP-CNT hybrids and provide guidance towards the rational design of high-performance catalysts for energy applications.

A Computer Program for the Preliminary Design of Contrarotating Propellers

DTIC Science & Technology

1975-12-01

10 062, 10 030’t .0b03𔃺 10062 Nt:=42,1 03Q 20030 MNNiJC 79 Lv L=M-1 SP:S IN (FLOAT (L) *8 (N, ID) AZL=AZLOCON1#CMP𔄂 (Mtg)*SKF 20038 BZL=BZL*CONi...81,82vJC1 Pm1=.IMPUN(t31 BI.,JC) PP 5 P P2/PP 3 9D06=SjNPUN(R1q8OJN~ P*7:sIP4PUN(dl s8 ,JC) P0d=S IMPUN(81,E39tJC) F’P9=PF / PB n~o 1C09 I:1,JC 03 10940 L=1...0 )r) =Y ( D) no? J:1,v4 IF (A) l1 t :-(XA-Ytjl)AC 3SU"=:SUMOPROt) A NS=S U* Copy brkabdlo to DDC does not pb ;ml fully ICYNGl reproduction -7-707 44

Hullborne Hydrofoil Six-Degree of Freedom Motion Prediction Computer Program

DTIC Science & Technology

1976-07-01

UAVEI (7.7) , WAVE2 (797) .!NUEX(1493) .DtIM3(4034) KRN 21 NOE=2 *NO%1 KRN 22 no0 12IzlNON KPZN 23 NIxN0N- I KPN 24 FR(I.1)xEM1 CK,1) KRN 25 FR(192)2-SNE...CON7(J,1)* WAVE2 (1,J)-CON2(NJ,1 )*SOUR2(1,J) KRN III PRA(1,3)=PRA(T,3)+CON1(J,2)*WAVEi CIJ)-CON1(NJ,2)*SOUR1(I.J) KRN 112 PRA(1,4)zPRA(194) .CON2(J,2...8217 WAVE2 (lj)-CON2(NJ,2)*SOUR2(IJJ KRN 113 PPV(1.2)=PRV(192) *CON2(J,1)*SOUR2(I.J) *CON2(NJt1)* WAVE2 (1.J) KRN 115 PRV(193;=PRV(193),CONI(Jt?)4SOUR1(1,J

Australasian microtektites: Impactor identification using Cr, Co and Ni ratios

NASA Astrophysics Data System (ADS)

Folco, L.; Glass, B. P.; D'Orazio, M.; Rochette, P.

2018-02-01

Impactor identification is one of the challenges of large-scale impact cratering studies due to the dilution of meteoritic material in impactites (typically < 1 wt%). The nature of the impactor that generated the Australasian tektite/microtektite strewn field, i.e., the largest Cenozoic strewn field (∼15% of the Earth's surface), the youngest (∼0.78 Myr old) on Earth, and the only one without an associated impact crater so far, is an outstanding issue. We identify a chondritic impactor signature in 77 Australasian microtektites (size range: ∼200-700 μm) from within 3000 km from the hypothetical impact location in Indochina (∼17°N, 107°E) based on variations of Cr, Co and Ni interelement ratios in a Co/Ni vs Cr/Ni space (46 microtektites analyzed in this work by Laser Ablation-Inductively Coupled Plasma -Mass Spectrometry and 31 from literature by means of Neutron Activation Analyses with Cr, Co and Ni concentrations up to ∼370, 50 and 680 μg/g, respectively). Despite substantial overlap in Cr/Ni versus Co/Ni composition for several meteorite types with chondritic composition (chondrites and primitive achondrites), regression calculation based on ∼85% of the studied microtektites best fit a mixing line between crustal compositions and an LL chondrite. However, due to some scatter mainly in the Cr versus Ni ratios in the considered dataset, an LL chondrite may not be the best fit to the data amongst impactors of primitive compositions. Eight high Ni/Cr and five low Ni/Cr outlier microtektites (∼15% in total) deviate from the above mixing trend, perhaps resulting from incomplete homogenization of heterogeneous impactor and target precursor materials at the microtektite scale, respectively. Together with previous evidence from the ∼35 Myr old Popigai impact spherules and the ∼1 Myr old Ivory Coast microtektites, our finding suggests that at least three of the five known Cenozoic distal impact ejecta were generated by the impacts of large stony asteroids of chondritic composition, and possibly of ordinary chondritic composition. The impactor signature found in Australasian microtektites documents mixing of target and impactor melts upon impact cratering. This requires target-impactor mixing in both the two competing models in literature for the formation of the Australasian tektites/microtektites: the impact cratering and low-altitude airburst plume models.

Cobalt and precious metals in sulphides of peridotite xenoliths and inferences concerning their distribution according to geodynamic environment: A case study from the Scottish lithospheric mantle

NASA Astrophysics Data System (ADS)

Hughes, Hannah S. R.; McDonald, Iain; Faithfull, John W.; Upton, Brian G. J.; Loocke, Matthew

2016-01-01

Abundances of precious metals and cobalt in the lithospheric mantle are typically obtained by bulk geochemical analyses of mantle xenoliths. These elements are strongly chalcophile and the mineralogy, texture and trace element composition of sulphide phases in such samples must be considered. In this study we assess the mineralogy, textures and trace element compositions of sulphides in spinel lherzolites from four Scottish lithospheric terranes, which provide an ideal testing ground to examine the variability of sulphides and their precious metal endowments according to terrane age and geodynamic environment. Specifically we test differences in sulphide composition from Archaean-Palaeoproterozoic cratonic sub-continental lithospheric mantle (SCLM) in northern terranes vs. Palaeozoic lithospheric mantle in southern terranes, as divided by the Great Glen Fault (GGF). Cobalt is consistently elevated in sulphides from Palaeozoic terranes (south of the GGF) with Co concentrations > 2.9 wt.% and Co/Ni ratios > 0.048 (chondrite). In contrast, sulphides from Archaean cratonic terranes (north of the GGF) have low abundances of Co (< 3600 ppm) and low Co/Ni ratios (< 0.030). The causes for Co enrichment remain unclear, but we highlight that globally significant Co mineralisation is associated with ophiolites (e.g., Bou Azzer, Morocco and Outokumpu, Finland) or in oceanic peridotite-floored settings at slow-spreading ridges. Thus we suggest an oceanic affinity for the Co enrichment in the southern terranes of Scotland, likely directly related to the subduction of Co-enriched oceanic crust during the Caledonian Orogeny. Further, we identify a distinction between Pt/Pd ratio across the GGF, such that sulphides in the cratonic SCLM have Pt/Pd ≥ chondrite whilst Palaeozoic sulphides have Pt/Pd < chondrite. We observe that Pt-rich sulphides with discrete Pt-minerals (e.g., PtS) are associated with carbonate and phosphates in two xenolith suites north of the GGF. This three-way immiscibility (carbonate-sulphide-phosphate) indicates carbonatitic metasomatism is responsible for Pt-enrichment in this (marginal) cratonic setting. These Co and Pt-enrichments may fundamentally reflect the geodynamic setting of cratonic vs. non-cratonic lithospheric terranes and offer potential tools to facilitate geochemical mapping of the lithospheric mantle.

Nano-fabricated perpendicular magnetic anisotropy electrodes for lateral spin valves and observation of Nernst-Ettingshausen related signals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chejanovsky, N.; Sharoni, A., E-mail: amos.sharoni@biu.ac.il

2014-08-21

Lateral spin valves (LSVs) are efficient structures for characterizing spin currents in spintronics devices. Most LSVs are based on ferromagnetic (FM) electrodes for spin-injection and detection. While there are advantages for using perpendicular magnetic anisotropy (PMA) FM, e.g., stability to nano-scaling, these have almost not been studied. This is mainly due to difficulties in fabricating PMA FMs in a lateral geometry. We present here an efficient method, based on ion-milling through an AlN mask, for fabrication of LSVs with multi-layered PMA FMs such as Co/Pd and Co/Ni. We demonstrate, using standard permalloy FMs, that the method enables efficient spin injection.more » We show the multi-layer electrodes retain their PMA properties as well as spin injection and detection in PMA LSVs. In addition, we find a large asymmetric voltage signal which increases with current. We attribute this to a Nernst-Ettingshausen effect caused by local Joule heating and the perpendicular magnetic easy axis.« less

Structural and DC electrical resistivity, magnetic properties of Co0.5M0.5Fe2O4 (M= Ni, Zn, and Mg) ferrite nanoparticles

NASA Astrophysics Data System (ADS)

Ramakrishna, A.; Murali, N.; Mammo, Tulu Wegayehu; Samatha, K.; Veeraiah, V.

2018-04-01

Inverse spinel structured nanoparticles of cobalt ferrite partially substituted by divalent cations of Ni, Zn, and Mg have been synthesized through sol-gel auto combustion route. Structural parameters are studied by powder X-ray diffraction at the diffraction angle range of 10-80°; and FT-IR spectroscopy in the wavenumber range of 1600-400 cm-1. Lattice parameters were calculated from the (hkl) values of the diffraction planes and interplanar spacing and found to be in the range of 8.3659-8.4197 Å. The surface morphology and crystalline nature are studied using scanning electron microscopy and also using HRTEM. The magnetic properties are analyzed through vibrating sample magnetometer. High saturation magnetization of 90.12 emu/g has been achieved from Co-Zn sample whereas high coercive force of 883.45 Oe is achieved in Co-Ni sample. A two-probe DC resistivity was measured in temperature ranges of 300-450 K.

Assessing the resistance and bioremediation ability of selected bacterial and protozoan species to heavy metals in metal-rich industrial wastewater

PubMed Central

2013-01-01

Background Heavy-metals exert considerable stress on the environment worldwide. This study assessed the resistance to and bioremediation of heavy-metals by selected protozoan and bacterial species in highly polluted industrial-wastewater. Specific variables (i.e. chemical oxygen demand, pH, dissolved oxygen) and the growth/die-off-rates of test organisms were measured using standard methods. Heavy-metal removals were determined in biomass and supernatant by the Inductively Couple Plasma Optical Emission Spectrometer. A parallel experiment was performed with dead microbial cells to assess the biosorption ability of test isolates. Results The results revealed that the industrial-wastewater samples were highly polluted with heavy-metal concentrations exceeding by far the maximum limits (in mg/l) of 0.05-Co, 0.2-Ni, 0.1-Mn, 0.1-V, 0.01-Pb, 0.01-Cu, 0.1-Zn and 0.005-Cd, prescribed by the UN-FAO. Industrial-wastewater had no major effects on Pseudomonas putida, Bacillus licheniformis and Peranema sp. (growth rates up to 1.81, 1.45 and 1.43 d-1, respectively) compared to other test isolates. This was also revealed with significant COD increases (p < 0.05) in culture media inoculated with living bacterial isolates (over 100%) compared to protozoan isolates (up to 24% increase). Living Pseudomonas putida demonstrated the highest removal rates of heavy metals (Co-71%, Ni-51%, Mn-45%, V-83%, Pb-96%, Ti-100% and Cu-49%) followed by Bacillus licheniformis (Al-23% and Zn-53%) and Peranema sp. (Cd-42%). None of the dead cells were able to remove more than 25% of the heavy metals. Bacterial isolates contained the genes copC, chrB, cnrA3 and nccA encoding the resistance to Cu, Cr, Co-Ni and Cd-Ni-Co, respectively. Protozoan isolates contained only the genes encoding Cu and Cr resistance (copC and chrB genes). Peranema sp. was the only protozoan isolate which had an additional resistant gene cnrA3 encoding Co-Ni resistance. Conclusion Significant differences (p < 0.05) observed between dead and living microbial cells for metal-removal and the presence of certain metal-resistant genes indicated that the selected microbial isolates used both passive (biosorptive) and active (bioaccumulation) mechanisms to remove heavy metals from industrial wastewater. This study advocates the use of Peranema sp. as a potential candidate for the bioremediation of heavy-metals in wastewater treatment, in addition to Pseudomonas putida and Bacillus licheniformis. PMID:23387904

Assessing the resistance and bioremediation ability of selected bacterial and protozoan species to heavy metals in metal-rich industrial wastewater.

PubMed

Kamika, Ilunga; Momba, Maggy N B

2013-02-06

Heavy-metals exert considerable stress on the environment worldwide. This study assessed the resistance to and bioremediation of heavy-metals by selected protozoan and bacterial species in highly polluted industrial-wastewater. Specific variables (i.e. chemical oxygen demand, pH, dissolved oxygen) and the growth/die-off-rates of test organisms were measured using standard methods. Heavy-metal removals were determined in biomass and supernatant by the Inductively Couple Plasma Optical Emission Spectrometer. A parallel experiment was performed with dead microbial cells to assess the biosorption ability of test isolates. The results revealed that the industrial-wastewater samples were highly polluted with heavy-metal concentrations exceeding by far the maximum limits (in mg/l) of 0.05-Co, 0.2-Ni, 0.1-Mn, 0.1-V, 0.01-Pb, 0.01-Cu, 0.1-Zn and 0.005-Cd, prescribed by the UN-FAO. Industrial-wastewater had no major effects on Pseudomonas putida, Bacillus licheniformis and Peranema sp. (growth rates up to 1.81, 1.45 and 1.43 d-1, respectively) compared to other test isolates. This was also revealed with significant COD increases (p < 0.05) in culture media inoculated with living bacterial isolates (over 100%) compared to protozoan isolates (up to 24% increase). Living Pseudomonas putida demonstrated the highest removal rates of heavy metals (Co-71%, Ni-51%, Mn-45%, V-83%, Pb-96%, Ti-100% and Cu-49%) followed by Bacillus licheniformis (Al-23% and Zn-53%) and Peranema sp. (Cd-42%). None of the dead cells were able to remove more than 25% of the heavy metals. Bacterial isolates contained the genes copC, chrB, cnrA3 and nccA encoding the resistance to Cu, Cr, Co-Ni and Cd-Ni-Co, respectively. Protozoan isolates contained only the genes encoding Cu and Cr resistance (copC and chrB genes). Peranema sp. was the only protozoan isolate which had an additional resistant gene cnrA3 encoding Co-Ni resistance. Significant differences (p < 0.05) observed between dead and living microbial cells for metal-removal and the presence of certain metal-resistant genes indicated that the selected microbial isolates used both passive (biosorptive) and active (bioaccumulation) mechanisms to remove heavy metals from industrial wastewater. This study advocates the use of Peranema sp. as a potential candidate for the bioremediation of heavy-metals in wastewater treatment, in addition to Pseudomonas putida and Bacillus licheniformis.

Elastic moduli and thermal expansion coefficients of medium-entropy subsystems of the CrMnFeCoNi high-entropy alloy

DOE PAGES

Laplanche, Guillaume; Gadaud, P.; Barsch, C.; ...

2018-02-23

Elastic moduli of a set of equiatomic alloys (CrFeCoNi, CrCoNi, CrFeNi, FeCoNi, MnCoNi, MnFeNi, and CoNi), which are medium-entropy subsystems of the CrMnFeCoNi high-entropy alloy were determined as a function of temperature over the range 293 K–1000 K. Thermal expansion coefficients were determined for these alloys over the temperature range 100 K–673 K. All alloys were single-phase and had the face-centered cubic (FCC) crystal structure, except CrFeNi which is a two-phase alloy containing a small amount of body-centered cubic (BCC) precipitates in a FCC matrix. The temperature dependences of thermal expansion coefficients and elastic moduli obtained here are useful formore » quantifying fundamental aspects such as solid solution strengthening, and for structural analysis/design. Furthermore, using the above results, the yield strengths reported in literature for these alloys were normalized by their shear moduli to reveal the influence of shear modulus on solid solution strengthening.« less

Uniaxial pressure effect on the magnetic ordered moment and transition temperatures in BaFe2 -xTxAs2 (T =Co,Ni )

NASA Astrophysics Data System (ADS)

Tam, David W.; Song, Yu; Man, Haoran; Cheung, Sky C.; Yin, Zhiping; Lu, Xingye; Wang, Weiyi; Frandsen, Benjamin A.; Liu, Lian; Gong, Zizhou; Ito, Takashi U.; Cai, Yipeng; Wilson, Murray N.; Guo, Shengli; Koshiishi, Keisuke; Tian, Wei; Hitti, Bassam; Ivanov, Alexandre; Zhao, Yang; Lynn, Jeffrey W.; Luke, Graeme M.; Berlijn, Tom; Maier, Thomas A.; Uemura, Yasutomo J.; Dai, Pengcheng

2017-02-01

We use neutron diffraction and muon spin relaxation to study the effect of in-plane uniaxial pressure on the antiferromagnetic (AF) orthorhombic phase in BaFe2As2 and its Co- and Ni-substituted members near optimal superconductivity. In the low-temperature AF ordered state, uniaxial pressure necessary to detwin the orthorhombic crystals also increases the magnetic ordered moment, reaching an 11% increase under 40 MPa for BaFe1.9Co0.1As2 , and a 15% increase for BaFe1.915Ni0.085As2 . We also observe an increase of the AF ordering temperature (TN) of about 0.25 K/MPa in all compounds, consistent with density functional theory calculations that reveal better Fermi surface nesting for itinerant electrons under uniaxial pressure. The doping dependence of the magnetic ordered moment is captured by combining dynamical mean field theory with density functional theory, suggesting that the pressure-induced moment increase near optimal superconductivity is closely related to quantum fluctuations and the nearby electronic nematic phase.

Al3+ ions dependent structural and magnetic properties of Co-Ni nano-alloys.

PubMed

Kadam, R H; Alone, Suresh T; Gaikwad, Anil S; Birajdar, A P; Shirsath, Sagar E

2014-06-01

Ferrite samples with a chemical formula Co0.5Ni0.5Al(x)Fe(2-x)O4 (where x = 0.0, 0.25, 0.5, 0.75 and 1.0) were synthesized by sol-gel auto-combustion method. The synthesized samples were annealed at 600 degrees C for 4 h. An analysis of X-ray diffraction (XRD) patterns reveals the formation of single phase cubic spinel structure. The lattice parameter decreased linearly with the increasing Al content x. Nano size of the powders were confirmed by the transmission electron micrographs (TEM). Particle size, bulk density decreased whereas specific surface area and porosity of the samples increased with the Al substitution. Cation distribution of constituent ions shows linear dependence of Al substitution. Based on the cation distribution obtained from XRD data, structural parameters such as lattice parameters, ionic radii of available sites and the oxygen parameter 'u' is calculated. Saturation magnetization (M(s)), magneton number (n(B)) and coercivity (H(c)) decreased with the Al substitution. Possible explanation for the observed structural and magnetic behavior with various Al content are discussed.

Interfacial exchange coupling and magnetization reversal in perpendicular [Co/Ni]N/TbCo composite structures.

PubMed

Tang, M H; Zhang, Zongzhi; Tian, S Y; Wang, J; Ma, B; Jin, Q Y

2015-06-15

Interfacial exchange coupling and magnetization reversal characteristics in the perpendicular heterostructures consisting of an amorphous ferrimagnetic (FI) TbxCo(100-x) alloy layer exchange-coupled with a ferromagnetic (FM) [Co/Ni]N multilayer have been investigated. As compared with pure TbxCo(100-x) alloy, the magnetization compensation composition of the heterostructures shift to a higher Tb content, implying Co/Ni also serves to compensate the Tb moment in TbCo layer. The net magnetization switching field Hc⊥ and interlayer interfacial coupling field Hex, are not only sensitive to the magnetization and thickness of the switched TbxCo(100-x) or [Co/Ni]N layer, but also to the perpendicular magnetic anisotropy strength of the pinning layer. By tuning the layer structure we achieve simultaneously both large Hc⊥ = 1.31 T and Hex = 2.19 T. These results, in addition to the fundamental interest, are important to understanding of the interfacial coupling interaction in the FM/FI heterostructures, which could offer the guiding of potential applications in heat-assisted magnetic recording or all-optical switching recording technique.

Separation of Ni and Co by D2EHPA in the Presence of Citrate Ion

NASA Astrophysics Data System (ADS)

Nadimi, Hamed; Haghshenas Fatmehsari, Davoud; Firoozi, Sadegh

2017-10-01

Recycling processes for the recovery of metallic content from the electronic wastes are environmentally friendly and economical. This paper reports a method for the recovery and separation of Ni and Co from the sulfate solution by the use of D2EHPA. In this regard, the influence of citrate ion, as a carboxylate ligand, was examined in the separation conditions of Ni and Co via D2EHPA (a poor selective extractant for Ni and Co separation). It was found that the Δ {pH}_{0.5}^{Ni-Co} (the difference between pH values corresponding to 50 pct extraction of metallic ion) increases to 1.5 at the citrate concentration of 0.05 M; this Δ {pH}_{0.5}^{Ni-Co} value is much higher than that obtained in the absence of citrate ion (0.1). Fourier Transform Infrared Spectroscopy (FT-IR) indicated that the citrate ion is co-absorbed during the metallic ions absorption by D2EHPA meaning that the metal-organic complexes contain Co/Ni and citrate ion. Also, the stoichiometric coefficients of the Ni and Co extraction reaction were proposed by applying the slope analysis method.

Crystal structure of N-de­acetyl­lappa­coni­tine

PubMed Central

Shi, Xin-Wei; Lu, Qiang-Qiang; Zhou, Jun-Hui; Cui, Xin-Ai

2015-01-01

The title compound, C30H42N2O7 [systematic name: (1S,4S,5S,7S,8S,9S,10S,11S,13R,14S,16S,17R)-20-ethyl-4,8,9-trihy­droxy-1,14,16-tri­meth­oxy­aconitan-4-yl 2-amino­benzoate], isolated from roots of Aconitum sinomontanum Nakai, is a typical aconitane-type C19-diterpenoid alkaloid, which crystallizes with two independent mol­ecules in the asymmetric unit. The conformations of the two independent mol­ecules are closely similar. Each mol­ecule comprises four six-membered rings (A, B, D and E) including one six-membered N-containing heterocyclic ring (E), and two five-membered rings (C and F). Rings A, B and E adopt chair conformations, while ring D displays a boat conformation. Five-membered rings C and F exhibit envelope conformations. IntramolecularN—H⋯O hydrogen bonds between the amino group and carbonyl O atom help to stabilize molecular structure. In the crystal, O—H⋯O hydrogen bonds link the mol­ecules into zigzag chains propagating in [010]. PMID:26396805

Elastic moduli and thermal expansion coefficients of medium-entropy subsystems of the CrMnFeCoNi high-entropy alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laplanche, Guillaume; Gadaud, P.; Barsch, C.

Elastic moduli of a set of equiatomic alloys (CrFeCoNi, CrCoNi, CrFeNi, FeCoNi, MnCoNi, MnFeNi, and CoNi), which are medium-entropy subsystems of the CrMnFeCoNi high-entropy alloy were determined as a function of temperature over the range 293 K–1000 K. Thermal expansion coefficients were determined for these alloys over the temperature range 100 K–673 K. All alloys were single-phase and had the face-centered cubic (FCC) crystal structure, except CrFeNi which is a two-phase alloy containing a small amount of body-centered cubic (BCC) precipitates in a FCC matrix. The temperature dependences of thermal expansion coefficients and elastic moduli obtained here are useful for quantifying fundamental aspects suchmore » as solid solution strengthening, and for structural analysis/design. Furthermore, using the above results, the yield strengths reported in literature for these alloys were normalized by their shear moduli to reveal the influence of shear modulus on solid solution strengthening.« less

Fabrication of Co0.5Ni0.5CrxFe2-xO4 materials via sol-gel method and their characterizations

NASA Astrophysics Data System (ADS)

Kadam, R. H.; Birajdar, A. P.; Alone, Suresh T.; Shirsath, Sagar E.

2013-02-01

Co0.5Ni0.5CrxFe2-xO4 nanoparticles have been designed by the sol-gel auto combustion method, using nitrates of the respective metal ions, and citric acid as the starting materials. The process takes only a few minutes to obtain as-received Cr-substituted Co-Ni ferrite powders. X-ray diffraction (XRD), vibrational sample magnetometer (VSM), transmission electron microscopy (TEM) are utilized in order to study the effect of variation in the Cr3+ substitution and its impact on particle size, lattice constant, specific surface area, cation distribution and magnetic properties. Lattice parameter, particle size found to decrease with increasing Cr3+ content, whereas specific surface area showed increasing trend with the Cr3+ substitution. Cation distribution indicates that the Cr, Co and Ni ions show preference toward octahedral [B] site, whereas Fe occupies both tetrahedral (A) and octahedral [B] sites. Saturation magnetization (MS) decreased from 65.1 to 40.6 emu/g with the increase in Cr3+ substitution. However, Coercivity increased from 198 to 365 Oe with the Cr3+ substitution.

Study on Properties of CoNi Films with mn Doping Prepared by Magnetic Fields Induced Codeposition Technology

NASA Astrophysics Data System (ADS)

Gang, Liang; Yu, Yundan; Ge, Hongliang; Wei, Guoying; Jiang, Li; Sun, Lixia

Magnetic field parallel to electric field was induced during plating process to prepare CoNiMn alloy films on copper substrate. Electrochemistry mechanism and properties of CoNiMn alloy films were investigated in this paper. Micro magnetohydrodynamic convection phenomenon caused by vertical component of current density and parallel magnetic field due to deformation of current distribution contributed directly to the improvement of cathode current and deposition rate. Cathode current of the CoNiMn plating system increased about 30% with 1T magnetic field induced. It was found that CoNiMn films electrodeposited with magnetic fields basically belonged to a kind of progressive nucleation mode. Higher magnetic intensity intended to obtain CoNiMn films with good crystal structures and highly preferred orientations. With the increase of magnetic intensities, surface morphology of CoNiMn alloy films changed from typically nodular to needle-like structures. Compared with coatings electrodeposited without magnetic field, CoNiMn alloy films prepared with magnetic fields possessed better magnetic properties. Coercivity, remanence and saturation magnetization of samples increased sharply when 1T magnetic field was induced during plating process.

Perpendicular STT_RAM cell in 8 nm technology node using Co1/Ni3(1 1 1)||Gr2||Co1/Ni3(1 1 1) structure as magnetic tunnel junction

NASA Astrophysics Data System (ADS)

Varghani, Ali; Peiravi, Ali; Moradi, Farshad

2018-04-01

The perpendicular anisotropy Spin-Transfer Torque Random Access Memory (P-STT-RAM) is considered to be a promising candidate for high-density memories. Many distinct advantages of Perpendicular Magnetic Tunnel Junction (P-MTJ) compared to the conventional in-plane MTJ (I-MTJ) such as lower switching current, circular cell shape that facilitates manufacturability in smaller technology nodes, large thermal stability, smaller cell size, and lower dipole field interaction between adjacent cells make it a promising candidate as a universal memory. However, for small MTJ cell sizes, the perpendicular technology requires new materials with high polarization and low damping factor as well as low resistance area product of a P-MTJ in order to avoid a high write voltage as technology is scaled down. A new graphene-based STT-RAM cell for 8 nm technology node that uses high perpendicular magnetic anisotropy cobalt/nickel (Co/Ni) multilayer as magnetic layers is proposed in this paper. The proposed junction benefits from enough Tunneling Magnetoresistance Ratio (TMR), low resistance area product, low write voltage, and low power consumption that make it suitable for 8 nm technology node.

Dispersive elastic properties of Dzyaloshinskii domain walls

NASA Astrophysics Data System (ADS)

Pellegren, James; Lau, Derek; Sokalski, Vincent

Recent studies on the asymmetric field-driven growth of magnetic bubble domains in perpendicular thin films exhibiting an interfacial Dzyaloshinskii-Moriya interaction (DMI) have provided a wealth of experimental evidence to validate models of creep phenomena, as key properties of the domain wall (DW) can be altered with the application of an external in-plane magnetic field. While asymmetric growth behavior has been attributed to the highly anisotropic DW energy, σ (θ) , which results from the combination of DMI and the in-plane field, many experimental results remain anomalous. In this work, we demonstrate that the anisotropy of DW energy alters the elastic response of the DW as characterized by the surface stiffness, σ (θ) = σ (θ) + σ (θ) , and evaluate the impact of this stiffness on the creep law. We find that at in-plane fields larger than and antiparallel to the effective field due to DMI, the DW stiffness decreases rapidly, suggesting that higher energy walls can actually become more mobile than their low energy counterparts. This result is consistent with experiments on CoNi multilayer films where velocity curves for domain walls with DMI fields parallel and antiparallel to the applied field cross over at high in-plane fields.

Raman Study of the Structural Distortion in the Ni 1–xCo xTiO 3 Solid Solution

DOE PAGES

Fujioka, Yukari; Frantti, Johannes; Puretzky, Alexander; ...

2016-09-08

In this paper, Raman spectra were collected on Ni 1–xCo xTiO 3 (0 ≤ x ≤ 1) ilmenite samples as a function of the temperature between 4 and 1200 K. An evident symmetry lowering from the prototype Rmore » $$\\bar{3}$$symmetry is observed. The distortion was largest for the x = 0.40 and 0.50 samples and significantly diminished for small and large values of x. The distortion was preserved in the whole temperature range and, except for the x = 0.50 sample, did not show significant changes. Notably, between 25 and 69 K, distortion of the x = 0.40 sample is accompanied by ferromagnetic order. The direct cation–cation and O-mediated indirect interactions are discussed as mechanisms behind the distortion and magnetic order. A reversible order–disorder phase transformation, assigned to occur between the ilmenite and corundum phases, took place at 973 K in the x = 0.50 sample. Completion of the transformation took over 1 h. Finally, the role of the overlap of Co/Ni and Ti 3d orbitals through O octahedral faces for charge transfer is discussed.« less

Origin and tuning of the magnetic anisotropy in Fe2P-based alloys

NASA Astrophysics Data System (ADS)

Zhuravlev, Ivan; Antropov, V. P.; Belashchenko, K. D.

Fe2P-based alloys have been studied for years due to their potential magnetocaloric applications. In addition, Fe2P demonstrates record-high magnetocrystalline anisotropy (MCA) for systems with no heavy elements. While the Curie temperature TC in pure Fe2P is too low for applications, this system appears to be highly tunable, and its TC can be greatly increased by alloying with many other d and p elements. Here we present the electronic structure analysis of magnetic properties of these alloys, searching for systems with higher TC while preserving high MCA. The microscopic origin of the dominant contribution to MCA and its concentration dependence is revealed. We further find that co-alloying with Co or Ni and Si is a promising strategy for achieving high Curie temperature and MCA, which is more favorable compared to individual alloying by Co/Ni or Si due to the compensation of their effects on the band occupation. Work at UNL supported by NSF Grants DMR-1308751 and DMR-1609776. Work at Ames Lab was supported by the Critical Materials Institute, an Energy Innovation Hub funded by the US DOE.

Spin-orbit torque based magnetization switching in Pt/Cu/[Co/Ni]5 multilayer structures

NASA Astrophysics Data System (ADS)

Ostwal, Vaibhav; Penumatcha, Ashish; Hung, Yu-Ming; Kent, Andrew D.; Appenzeller, Joerg

2017-12-01

Spin-Orbit Torque (SOT) in Heavy Metal/Ferromagnet (HM/FM) structures provides an important tool to control the magnetization of FMs and has been an area of interest for memory and logic implementation. Spin transfer torque on the FM in such structures is attributed to two sources: (1) the Spin Hall effect in the HM and (2) the Rashba-effect at the HM/FM interface. In this work, we study the SOT in a Pt/[Co,Ni] structure and compare its strength with the SOT in a Pt/Cu/[Co,Ni] structure where copper, a metal with a low spin-orbit interaction, is inserted between the Pt (HM) layer and the [Co,Ni] (FM) layer. We use an AC harmonic measurement technique to measure the strength of the SOT on the magnetic thin-film layer. Our measurements show that a significant SOT is exerted on the magnetization even after a 6 nm thick copper layer is inserted between the HM and the FM. Also, we find that this torque can be used to switch a patterned magnetic layer in the presence of an external magnetic field.

CoM(M=Fe,Cu,Ni)-embedded nitrogen-enriched porous carbon framework for efficient oxygen and hydrogen evolution reactions

NASA Astrophysics Data System (ADS)

Feng, Xiaogeng; Bo, Xiangjie; Guo, Liping

2018-06-01

Rational synthesis and development of earth-abundant materials with efficient electrocatalytic activity and stability for water splitting is a critical but challenging step for sustainable energy application. Herein, a family of bimetal (CoFe, CoCu, CoNi) embedded nitrogen-doped carbon frameworks is developed through a facile and simple thermal conversion strategy of metal-doped zeolitic imidazolate frameworks. Thanks to collaborative superiorities of abundant M-N-C species, modulation action of secondary metal, cobalt-based electroactive phases, template effect of MOFs and unique porous structure, bimetal embedded nitrogen-doped carbon frameworks materials manifest good oxygen and hydrogen evolution catalytic activity. Especially, after modulating the species and molar ratio of metal sources, optimal Co0.75Fe0.25 nitrogen-doped carbon framework catalyst just requires a low overpotential of 303 mV to achieve 10 mA cm-2 with a low Tafel slope (39.49 mV dec-1) for oxygen evolution reaction, which even surpasses that of commercial RuO2. In addition, the optimal catalyst can function as an efficient bifunctional electrocatalyst for overall water splitting with satisfying activity and stability. This development offers an attractive direction for the rational design and fabrication of porous carbon materials for electrochemical energy applications.

S, N‐Co‐Doped Graphene‐Nickel Cobalt Sulfide Aerogel: Improved Energy Storage and Electrocatalytic Performance

PubMed Central

He, Guanjie; Qiao, Mo; Li, Wenyao; Lu, Yao; Zhao, Tingting; Zou, Rujia; Li, Bo; Darr, Jawwad A.; Hu, Junqing; Titirici, Maria‐Magdalena

2016-01-01

Metal sulfides are commonly used in energy storage and electrocatalysts due to their redox centers and active sites. Most literature reports show that their performance decreases significantly caused by oxidation in alkaline electrolyte during electrochemical testing. Herein, S and N co‐doped graphene‐based nickel cobalt sulfide aerogels are synthesized for use as rechargeable alkaline battery electrodes and oxygen reduction reaction (ORR) catalysts. Notably, this system shows improved cyclability due to the stabilization effect of the S and N co‐doped graphene aerogel (SNGA). This reduces the rate of oxidation and the decay of electronic conductivity of the metal sulfides materials in alkaline electrolyte, i.e., the capacity decrease of CoNi2S4/SNGA is 4.2% for 10 000 cycles in a three‐electrode test; the current retention of 88.6% for Co—S/SNGA after 12 000 s current–time chronoamperometric response in the ORR test is higher than corresponding Co—S nanoparticles and Co—S/non‐doped graphene aerogels. Importantly, the results here confirm that the Ni—Co—S ternary materials behave as an electrode for rechargeable alkaline batteries rather than supercapacitors electrodes in three‐electrode test as commonly described and accepted in the literature. Furthermore, formulas to evaluate the performance of hybrid battery devices are specified. PMID:28105397

[An analysis of essential health research in Chile].

PubMed

Armas Merino, Rodolfo; Torres Canales, Adrián

2017-07-01

Essential research studies of health problems affecting the majority of the population, aiming at actions that are feasible to be taken, efficiently and effectively implementing there and seeking solutions to unsolved problems. This is a complex process, which requires long lasting participation and coordinated interaction between different relevant sectors, namely the academic world, health policymakers and health-related industries. An analysis of essential health research in Chile is presented, considering factors such as shared efforts between the academic and health care sectors and the role of the Ministry of Health in research promotion. The following suggestions are made: 1) The Ministry of Health, along with universities, should stimulate, guide and monitor research activities that enrich and update the work on priority health issues; 2) To strengthen the capacity building of clinical or public health specialists by training them in applied research within medical centers, mainly teaching centers; 3) To assess the performance of National Fund for Health Research and Development (FONIS) and, if necessary, increase its resources to stimulate applied research in health; 4) To establish priorities for essential research, more specific than those proposed in 2010; 5) To reactivate the National Council for Health Research (CONIS) as an autonomous entity that coordinates applied research within the Ministry of Health.

CoPtB(O) alloy films as new perpendicular recording media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayashi, K.; Hayakawa, M.; Ohmori, H.

In search of new hard magnetic materials with high saturation magnetization and large coercivity, a comprehensive study was made on numerous Co- and CoPt-base crystalline alloys by means of sputtering techniques. It revealed that a newly found CoPtB(O) alloy system possessed excellent hard magnetic properties with remarkably large perpendicular coercivity and high saturation magnetization. This new alloy film, deposited onto room temperature substrates, shows the magnetic properties of 4{pi}{ital M}{sub {ital s}}=12 kG, {ital H}{sup {perpendicular}}{sub {ital c}}=4000 Oe, and perpendicular anisotropy field {ital H}{sub {ital k}}=22 kOe. These values are superior to those of prevailing materials such as CoCrmore » perpendicular and CoPt or CoNi longitudinal recording media. The typical composition is Co{sub 69}Pt{sub 20}B{sub 6}O{sub 5} (at. %), and oxygen plays a momentous role on the coercivity in this alloy film. As a magnetic recording medium, a write/read experiment of this film shows that the readout signal has a +9 dB peak-to-peak amplitude compared with that of metal particle tape at 1 {mu}m wavelength and has +10 dB compared with that of a CoCr perpendicular medium at 0.5 {mu}m wavelength.« less

Layered transition metal carboxylates: synthesis, structural aspects and observation of multi-step magnetic transition through phase diagram.

PubMed

Sen, Rupam; Mal, Dasarath; Lopes, Armandina M L; Brandão, Paula; Araújo, João P; Lin, Zhi

2013-10-01

Two new layered transition metal carboxylate frameworks, [Co3(L)2(H2O)6]·2H2O () and [Ni3(L)2(H2O)6]·2H2O () (L = tartronate anion or hydroxymalonic acid), have been synthesized and characterized by X-ray single crystal analysis. Both compounds have similar 2D structures. In both compounds there are two types of metal centers where one center is doubly bridged by the alkoxy oxygen atoms through μ2-O bridging to form a 1D infinite chain parallel to the crystallographic b-axis with the corners shared between the metal polyhedra. Magnetic susceptibility measurements revealed the existence of antiferromagnetic short range correlations between Co(Ni) intra-chain metal centers (with exchange constants JCo = -22.6 and JNi = -35.4 K). At low temperatures, long range order is observed in both compounds at Néel temperatures of 11 (for ) and 16 (for ) K, revealing that other exchange interactions, rather than the intra-chain ones, play a role in these systems. Whereas compound has an antiferromagnetic ground state, compound exhibits a ferromagnetic component, probably due to spin canting. Isothermal magnetization data unveiled a rich phase diagram with three metamagnetic phase transitions below 8 K in compound .

Atomistic Modeling of Diffusion and Phase Transformations in Metals and Alloys

NASA Astrophysics Data System (ADS)

Purja Pun, Ganga Prasad

Dissertation consists of multiple works. The first part is devoted to self-diffusion along dislocation cores in aluminum followed by the development of embedded atom method potentials for Co, NiAl, CoAl and CoNi systems. The last part focuses on martensitic phase transformation (MPT) in Ni xAl1--x and Al xCoyNi1-- x--y alloys. New calculation methods were developed to predict diffusion coefficients in metal as functions of temperature. Self-diffusion along screw and edge dislocations in aluminum was studied by molecular dynamic (MD) simulations. Three types of simulations were performed with and without (intrinsic) pre-existing vacancies and interstitials in the dislocation core. We found that the diffusion along the screw dislocation was dominated by the intrinsic mechanism, whereas the diffusion along the edge dislocation was dominated by the vacancy mechanism. The diffusion along the screw dislocation was found to be significantly faster than the diffusion along the edge dislocation, and the both diffusivities were in reasonable agreement with experimental data. The intrinsic diffusion mechanism can be associated with the formation of dynamic Frenkel pairs, possibly activated by thermal jogs and/or kinks. The simulations show that at high temperatures the dislocation core becomes an effective source/sink of point defects and the effect of pre-existing defects on the core diffusivity diminishes. First and the foremost ingredient needed in all atomistic computer simulations is the description of interaction between atoms. Interatomic potentials for Co, NiAl, CoAl and CoNi systems were developed within the Embedded Atom Method (EAM) formalism. The binary potentials were based on previously developed accurate potentials for pure Ni and pure Al and pure Co developed in this work. The binaries constitute a version of EAM potential of AlCoNi ternary system. The NiAl potential accurately reproduces a variety of physical properties of the B2-NiAl and L12--Ni3Al phases. The potential is expected to be especially suitable for simulations of hetero-phase interfaces and mechanical behavior of NiAl alloys. Apart from properties of the HCP Co, the new Co potential is accurate enough to reproduce several properties of the FCC Co which were not included in the potential fit. It shows good transferability property. The CoAl potential was fitted to the properties of B2-CoAl phase as in the NiAl fitting where as the NiCo potential was fitted to the ab initio formation energies of some imaginary phases and structures. Effect of chemical composition and uniaxial mechanical stresses was studied on the martensitic phase transformation in B2 type Ni-rich NiAl and AlCoNi alloys. The martensitic phase has a tetragonal crystal structure and can contain multiple twins arranged in domains and plates. The twinned martensites were always formed under the uniaxial compression where as the single variant martensites were the results of the uniaxial tension. The transformation was reversible and characterized by a significant temperature hysteresis. The magnitude of the hysteresis depends on the chemical composition and stress.

THE ELECTROCHEMICAL PROPERTIES OF FOUR DENTAL CASTING SUPRASTRUCTURE ALLOYS COUPLED WITH TITANIUM IMPLANTS

PubMed Central

Tuna, Suleyman Hakan; Pekmez, Nuran Ozcícek; Keyf, Filiz; Canlí, Fulya

2009-01-01

Objectives: As the choice of suprastructure alloy to be combined with titanium for the oral cavity is still a much debated issue, the aim of this study was to investigate the electrochemical interaction of the suprastructure/implant couples under the determined experiment conditions. Material and Methods: The potentiodynamic polarization curves and open-circuit potentials (OCP) of four UCLA type suprastructures coupled with straight Swiss Plus implant fixtures were taken in Afnor type artificial saliva solution at 37°C. The concentration of ions leached into artificial saliva solutions was estimated with ICP-MS. SEM images of the margins of suprastructure/implant couples were obtained before and after the electrochemical tests. Results: The OCP value of titanium became passive at the most negative potential. The lowest difference between the initial and constant OCP value was exhibited by the Au based suprastructure. Suprastructures made greater contributions to the potentiodynamic polarization curves of the implant/suprastructure couples. According to the ICP-MS results, Pd based and Au based couples dissolved less than Co-Ni based and Co-Cr based couples. Conclusions: Within the conditions this study, it may be concluded that the titanium implant forms a stable passive oxide layer in artificial saliva exposed to open air and does not affect the corrosion properties of the suprastructures. Pd based and Au based couples have been found to be more corrosion-resistant than base alloy couples. PMID:19936528

Application of Chemical Doping and Architectural Design Principles To Fabricate Nanowire Co2Ni3ZnO8 Arrays for Aqueous Asymmetric Supercapacitors.

PubMed

Liu, Qi; Yang, Bin; Liu, Jingyuan; Yuan, Yi; Zhang, Hongsen; Liu, Lianhe; Wang, Jun; Li, Rumin

2016-08-10

Electrode materials derived from transition metal oxides have a serious problem of low electron transfer rate, which restricts their practical application. However, chemically doped graphene transforms the chemical bonding configuration to enhance electron transfer rate and, therefore, facilitates the successful fabrication of Co2Ni3ZnO8 nanowire arrays. In addition, the Co2Ni3ZnO8 electrode materials, considered as Ni and Zn ions doped into Co3O4, have a high electron transfer rate and electrochemical response capability, because the doping increases the degree of crystal defect and reaction of Co/Ni ions with the electrolyte. Hence, the Co2Ni3ZnO8 electrode exhibits a high rate property and excellent electrochemical cycle stability, as determined by electrochemical analysis of the relationship between specific capacitance, IR drop, Coulomb efficiency, and different current densities. From the results of a three-electrode system of electrochemical measurement, the Co2Ni3ZnO8 electrode demonstrates a specific capacitance of 1115 F g(-1) and retains 89.9% capacitance after 2000 cycles at a current density of 4 A g(-1). The energy density of the asymmetric supercapacitor (AC//Co2Ni3ZnO8) is 54.04 W h kg(-1) at the power density of 3200 W kg(-1).

Elementary reaction modeling of reversible CO/CO2 electrochemical conversion on patterned nickel electrodes

NASA Astrophysics Data System (ADS)

Luo, Yu; Shi, Yixiang; Li, Wenying; Cai, Ningsheng

2018-03-01

CO/CO2 are the major gas reactant/product in the fuel electrode of reversible solid oxide cells (RSOC). This study proposes a two-charge-transfer-step mechanism to describe the reaction and transfer processes of CO-CO2 electrochemical conversion on a patterned Ni electrode of RSOC. An elementary reaction model is developed to couple two charge transfer reactions, C(Ni)+O2-(YSZ) ↔ CO(Ni)+(YSZ) +2e- and CO(Ni)+O2-(YSZ) ↔ CO2(Ni)+(YSZ)+2e-, with adsorption/desorption, surface chemical reactions and surface diffusion. This model well validates in both solid oxide electrolysis cell (SOEC) and solid oxide fuel cell (SOFC) modes by the experimental data from a patterned Ni electrode with 10 μm stripe width at different pCO (0-0.25 atm), pCO2 (0-0.35 atm) and operating temperature (600-700 °C). This model indicates SOEC mode is dominated by charge transfer step C(Ni)+O2-(YSZ)↔CO(Ni)+(YSZ) +2e-, while SOFC mode by CO(Ni)+ O2-(YSZ)↔CO2(Ni)+(YSZ)+2e- on the patterned Ni electrode. The sensitivity analysis shows charge transfer step is the major rate-determining step for RSOC, besides, surface diffusion of CO and CO2 as well as CO2 adsorption also plays a significant role in the electrochemical reaction of SOEC while surface diffusion of CO and CO2 desorption could be co-limiting in SOFC.

Synthesis and study of structural, microstructural and dielectric properties of Ce3+ doped Co-Ni ferrites for automotive applications

NASA Astrophysics Data System (ADS)

Srinivasamurthy, K. M.; Angadi, V. Jagadeesha; Kumar, P. Mohan; Nagaraj, B. S.; Deepthy, P. R.; Pasha, U. Mahaboob; Rudraswamy, B.

2018-05-01

Nano crystalline spinel ferrites of Co0.5Ni0.5CexFe2-xO4 (x=0.01, 0.015, 0.02, 0.025 and 0.03) was prepared by modified solution combustion method using a mixture of fuels for the first time. The influence of rare earth Ce3+ substitution at the Fe3+ site on the structural, microstructural and dielectric properties of Co0.5Ni0.5CexFe2-xO4 was investigated. The X-ray diffraction (XRD) studies confirmed the formation of monophasic nano crystalline samples without any secondary phases. The crystallite size decreases and density increases with the increases of Ce3+ contents. Surface morphology was studied through Scanning Electron Microscopy (SEM). Dielectric properties of these ferrites have been studied at room temperature using impedance analyzer in the frequency range up to 20 MHz. The effect of frequency and composition on dielectric constant (ɛ'), dielectric loss (tanδ) and ac conductivity (σac) have been discussed in terms of hopping of charge carriers (Fe2+↔Fe3+). The decrease in dielectric loss with frequency follows Debye's relaxation phenomena. Both the variation in tan loss and dielectric loss with frequency shows a similar. AC conductivity increases with the increases of frequency which directly proportional to concentration of Ce3+ ions follows Jonscher law. These Cerium doped Cobalt-nickel ferrites are very helpful for automotive applications.

Two 3D structured Co-Ni bimetallic oxides as cathode catalysts for high-performance alkaline direct methanol fuel cells

NASA Astrophysics Data System (ADS)

Liu, Yan; Shu, Chengyong; Fang, Yuan; Chen, Yuanzhen; Liu, Yongning

2017-09-01

Two NiCo2O4 bimetallic oxides were synthesized via a facile hydrothermal method. SEM and TEM observations show that these materials have three-dimensional (3D) dandelion-like (DL) and flower-like (FL) morphologies. Their large specific surface areas (90.68 and 19.8 m2·g-1) and porous structures provide many active sites and effective transport pathways for the oxygen reduction reaction (ORR). Electrochemical measurements with a rotating ring-disc electrode (RRDE) indicate that the electron transfer numbers of the NiCo2O4-DL and NiCo2O4-FL catalysts for ORR in an alkaline solution are 3.97 and 3.91, respectively. Fuel cells were assembled with the bimetallic oxides, PtRu/C and a polymer fiber membrane (PFM) as cathode catalysts, anode catalyst and electrolyte film, respectively. For NiCo2O4-DL, the peak power density reaches up to 73.5 mW·cm-2 at 26 °C, which is the highest room-temperature value reported to date. The high catalytic activity of NiCo2O4 is mainly attributed to the presence of many Co3+ cations that directly donate electrons to O2 to reduce it via a more efficient and effective route. Furthermore, the catalytic performance of NiCo2O4-DL is superior to that of NiCo2O4-FL because it has a higher specific surface area and is less crystalline.

Advanced bifunctional electrocatalyst generated through cobalt phthalocyanine tetrasulfonate intercalated Ni2Fe-layered double hydroxides for a laminar flow unitized regenerative micro-cell

NASA Astrophysics Data System (ADS)

Zhong, Haihong; Tian, Ran; Gong, Xiaoman; Li, Dianqing; Tang, Pinggui; Alonso-Vante, Nicolas; Feng, Yongjun

2017-09-01

We fabricated a NiFeOx/CoNy-C nanocomposite derived from CoPcTs-intercalated Ni2Fe-layered double hydroxides (Ni2Fe-CoPcTs-LDH), which served as high-efficiency, low-cost, and long-durability bifunctional oxygen electrocatalyst in half-cell, and a H2-O2 laminar flow unitized regenerative micro-cell (LFURMC) in alkaline media. Based on the synergistic effect between Co-Ny and NiFeOx centers, the non-noble hybrid catalyst NiFeOx/CoNy-C achieves a ΔE (η@jOER,10 - η@jORR,-3) = 0.84 V in alkaline solution, outperforming the commercial Pt/C, and very close to that of IrOx/C. In the fuel cell mode, the performance of NiFeOx/CoNy-C with the maximum power density of 56 mW cm-2 is similar to that of Pt/C (63 mW cm-2) and IrOx/C (58 mW cm-2); in the electrolysis mode, the calculated maximum electrical power consumed on NiFeOx/CoNy-C (237 mW cm-2) is more than 3 times that on Pt/C (73 mW cm-2), similar with that of IrOx/C. More importantly, the NiFeOx/CoNy-C shows a remarkable stability in alternating modes in a LFURMC system.

Controllable Fabrication and Tuned Electrochemical Performance of Potassium Co-Ni Phosphate Microplates as Electrodes in Supercapacitors.

PubMed

Liang, Bo; Chen, Yule; He, Jiangyu; Chen, Chen; Liu, Wenwen; He, Yuanqing; Liu, Xiaohe; Zhang, Ning; Roy, Vellaisamy A L

2018-01-31

Most reported pristine phosphates, such as NH 4 MPO 4 ·H 2 O (M = Co, Ni), are not very stable as supercapacitor electrodes because of their chemical properties. In this work, KCo x Ni 1-x PO 4 ·H 2 O microplates were fabricated by a facile hydrothermal method at low temperature and used as electrodes in supercapacitors. The Co and Ni content could be adjusted, and optimal electrochemical performance was found in KCo 0.33 Ni 0.67 PO 4 ·H 2 O, which also possessed superior specific capacitance, rate performance, and long-term chemical stability compared with NH 4 Co 0.33 Ni 0.67 PO 4 ·H 2 O because of its unique chemical composition and microstructure. Asymmetric supercapacitor cells based on KCo 0.33 Ni 0.67 PO 4 ·H 2 O and active carbon were assembled, which produce specific capacitance of 34.7 mA h g -1 (227 F g -1 ) under current density of 1.5 A g -1 and retain 82% as initial specific capacitance after charging and discharging approximately 5000 times. The assembled asymmetric supercapacitor cells (ASCs) exhibited much higher power and energy density than most previously reported transition metal phosphate ASCs. The KCo x Ni 1-x PO 4 ·H 2 O electrodes fabricated in this work are efficient, inexpensive, and composed of naturally abundant materials, rendering them promising for energy storage device applications.

Controlled crystallization and granulation of nano-scale β-Ni(OH) 2 cathode materials for high power Ni-MH batteries

NASA Astrophysics Data System (ADS)

He, Xiangming; Li, Jianjun; Cheng, Hongwei; Jiang, Changyin; Wan, Chunrong

A novel synthesis of controlled crystallization and granulation was attempted to prepare nano-scale β-Ni(OH) 2 cathode materials for high power Ni-MH batteries. Nano-scale β-Ni(OH) 2 and Co(OH) 2 with a diameter of 20 nm were prepared by controlled crystallization, mixed by ball milling, and granulated to form about 5 μm spherical grains by spray drying granulation. Both the addition of nano-scale Co(OH) 2 and granulation significantly enhanced electrochemical performance of nano-scale Ni(OH) 2. The XRD and TEM analysis shown that there were a large amount of defects among the crystal lattice of as-prepared nano-scale Ni(OH) 2, and the DTA-TG analysis shown that it had both lower decomposition temperature and higher decomposition reaction rate, indicating less thermal stability, as compared with conventional micro-scale Ni(OH) 2, and indicating that it had higher electrochemical performance. The granulated grains of nano-scale Ni(OH) 2 mixed with nano-scale Co(OH) 2 at Co/Ni = 1/20 presented the highest specific capacity reaching its theoretical value of 289 mAh g -1 at 1 C, and also exhibited much improved electrochemical performance at high discharge capacity rate up to 10 C. The granulated grains of nano-scale β-Ni(OH) 2 mixed with nano-scale Co(OH) 2 is a promising cathode active material for high power Ni-MH batteries.

3D carbon/cobalt-nickel mixed-oxide hybrid nanostructured arrays for asymmetric supercapacitors.

PubMed

Zhu, Jianhui; Jiang, Jian; Sun, Zhipeng; Luo, Jingshan; Fan, Zhanxi; Huang, Xintang; Zhang, Hua; Yu, Ting

2014-07-23

The electrochemical performance of supercapacitors relies not only on the exploitation of high-capacity active materials, but also on the rational design of superior electrode architectures. Herein, a novel supercapacitor electrode comprising 3D hierarchical mixed-oxide nanostructured arrays (NAs) of C/CoNi3 O4 is reported. The network-like C/CoNi3 O4 NAs exhibit a relatively high specific surface area; it is fabricated from ultra-robust Co-Ni hydroxide carbonate precursors through glucose-coating and calcination processes. Thanks to their interconnected three-dimensionally arrayed architecture and mesoporous nature, the C/CoNi3 O4 NA electrode exhibits a large specific capacitance of 1299 F/g and a superior rate performance, demonstrating 78% capacity retention even when the discharge current jumps by 100 times. An optimized asymmetric supercapacitor with the C/CoNi3 O4 NAs as the positive electrode is fabricated. This asymmetric supercapacitor can reversibly cycle at a high potential of 1.8 V, showing excellent cycling durability and also enabling a remarkable power density of ∼13 kW/kg with a high energy density of ∼19.2 W·h/kg. Two such supercapacitors linked in series can simultaneously power four distinct light-emitting diode indicators; they can also drive the motor of remote-controlled model planes. This work not only presents the potential of C/CoNi3 O4 NAs in thin-film supercapacitor applications, but it also demonstrates the superiority of electrodes with such a 3D hierarchical architecture. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Gold and trace element zonation in pyrite using a laser imaging technique: Implications for the timing of gold in orogenic and carlin-style sediment-hosted deposits

USGS Publications Warehouse

Large, R.R.; Danyushevsky, L.; Hollit, C.; Maslennikov, V.; Meffre, S.; Gilbert, S.; Bull, S.; Scott, R.; Emsbo, P.; Thomas, H.; Singh, B.; Foster, J.

2009-01-01

Laser ablation ICP-MS imaging of gold and other trace elements in pyrite from four different sediment- hosted gold-arsenic deposits has revealed two distinct episodes of gold enrichment in each deposit: an early synsedimentary stage where invisible gold is concentrated in arsenian diagenetic pyrite along with other trace elements, in particular, As, Ni, Pb, Zn, Ag, Mo, Te, V, and Se; and a later hydrothermal stage where gold forms as either free gold grains in cracks in overgrowth metamorphic and/or hydrothermal pyrite or as narrow gold- arsenic rims on the outermost parts of the overgrowth hydrothermal pyrite. Compared to the diagenetic pyrites, the hydrothermal pyrites are commonly depleted in Ni, V, Zn, Pb, and Ag with cyclic zones of Co, Ni, and As concentration. The outermost hydrothermal pyrite rims are either As-Au rich, as in moderate- to high- grade deposits such as Carlin and Bendigo, or Co-Ni rich and As-Au poor as in moderate- to low-grade deposits such as Sukhoi Log and Spanish Mountain. The early enrichment of gold in arsenic-bearing syngenetic to diagenetic pyrite, within black shale facies of sedimentary basins, is proposed as a critical requirement for the later development of Carlin-style and orogenic gold deposits in sedimentary environments. The best grade sediment-hosted deposits appear to have the gold climax event, toward the final stages of deformation-related hydrothermal pyrite growth and fluid flow. ?? 2009 Society of Economic Geologists, Inc.

Intérêt de la scintigraphie lymphatique et place de la chirurgie dans les chylothorax congénitaux

PubMed Central

Methlouthi, Jihène; Mahdhaoui, Nabiha; Bellalah, Manel; Selsabil, Nouir; Hedia, Ayache; Sfar, Raja; Essabah, Habib; Abdellatif, Nouri; Sonia, Nouri; Hassen, Seboui

2016-01-01

Le chylothorax est défini par l'accumulation du liquide lymphatique dans la cavité pleurale. Il existe 3 catégories distinctes chez le nouveau-né: les chylothorax congénitaux (CC), les chylothorax malformatifs ou syndromiques (CM) et les chylothorax post-opératoires (CO). Bien que rare, le chylothorax représente la cause la plus fréquente des épanchements pleuraux en période néonatale. Son diagnostic positif est facile par analyse du liquide pleural, mais son mécanisme et surtout l'intégrité du canal thoracique et ses collatérales est parfois difficile à préciser. La lymphoscintigraphie représente l'examen de choix dans le diagnostic etipathogénique. Ce moyen de diagnostic peut être couplé, si possible, au SPECT-CT (single photon emission tomography/computed tomography) permettant de donner des renseignements plus précis, notamment sur le plan anatomique. Sa prise en charge repose sur le drainage du liquide pleural, la suppression des graisses alimentaires et la nutrition parentérale. Le recours à la chirurgie est préconisé devant l'échec du traitement médical. Nous rapportons l'observation d'un nouveau-né porteur d'un chylothorax unilatéral, n'ayant pas répondu au traitement médical. La lymphoscintigraphie avait permis de diagnostiquer le mécanisme étiopathogénique et par conséquent, de guider le traitement chirurgical. PMID:28154676

Periodic table of 3d-metal dimers and their ions.

PubMed

Gutsev, G L; Mochena, M D; Jena, P; Bauschlicher, C W; Partridge, H

2004-10-08

The ground states of the mixed 3d-metal dimers TiV, TiCr, TiMn, TiFe, TiCo, TiNi, TiCu, TiZn, VCr, VMn, VFe, VCo, VNi, VCu, VZn, CrMn, CrFe, CrCo, CrNi, CrCu, CrZn, MnFe, MnCo, MnNi, MnCu, MnZn, FeCo, FeNi, FeCu, FeZn, CoNi, CoCu, CoZn, NiCu, NiZn, and CuZn along with their singly negatively and positively charged ions are assigned based on the results of computations using density functional theory with generalized gradient approximation for the exchange-correlation functional. Except for TiCo and CrMn, our assignment agrees with experiment. Computed spectroscopic constants (r(e),omega(e),D(o)) are in fair agreement with experiment. The ground-state spin multiplicities of all the ions are found to differ from the spin multiplicities of the corresponding neutral parents by +/-1. Except for TiV, MnFe, and MnCu, the number of unpaired electrons, N, in a neutral ground-state dimer is either N(1)+N(2) or mid R:N(1)-N(2)mid R:, where N(1) and N(2) are the numbers of unpaired 3d electrons in the 3d(n)4s(1) occupation of the constituent atoms. Combining the present and previous results obtained at the same level of theory for homonuclear 3d-metal and ScX (X=Ti-Zn) dimers allows one to construct "periodic" tables of all 3d-metal dimers along with their singly charged ions.

May a unitary autonomic index help assess autonomic cardiac regulation in elite athletes? Preliminary observations on the national Italian Olympic committee team.

PubMed

Sala, Roberto; Malacarne, Mara; Tosi, Fabio; Benzi, Manuela; Solaro, Nadia; Tamorri, Stefano; Spataro, Antonio; Pagani, Massimo; Lucini, Daniela

2017-12-01

Long term endurance training, as occurring in elite athletes, is associated to cardiac neural remodeling in favor of cardioprotective vagal mechanisms, resulting in resting bradycardia and augmented contribution of cardiac parasympathetic nerve activity. Autonomic assessment can be performed by way of heart rate variability. This technique however provides multiple indices, and there is not yet complete agreement on their specific significance. Purpose of the study was to assess whether a rank transformation and radar plot could provide a unitary autonomic index, capable to show a correlation between intensity of individual work and quality of autonomic regulation. We studied 711 (23.6±6.2 years) elite athletes that took part in the selection procedure for the 2016 Rio Olympic Games for the National Italian Olympic Committee (CONI). Indices from Heart Rate Variability HRV obtained at rest, during standing up and during recovery from an exercise test were used to compute a percent ranked unitary autonomic index for sport (ANSIs), taken as proxy of quality of autonomic regulation. Within the observed wide range of energy expenditure, the unitary autonomic index ANSIs appears significantly correlated to individual and discipline specific training workloads (r=0.25, P<0.001 and r=0.78, P<0.001, respectively), correcting for possible age and gender bias. ANSIs also positively correlates to lipid profile. Estimated intensity of physical activity correlates with quality of cardiac autonomic regulation, as expressed by a novel unitary index of cardiac autonomic regulation. ANSIs could provide a novel and convenient approach to individual autonomic evaluation in athletes.

Bimetallic CoNiSx nanocrystallites embedded in nitrogen-doped carbon anchored on reduced graphene oxide for high-performance supercapacitors.

PubMed

Chen, Qidi; Miao, Jinkang; Quan, Liang; Cai, Daoping; Zhan, Hongbing

2018-02-22

Exploring high-performance and low-priced electrode materials for supercapacitors is important but remains challenging. In this work, a unique sandwich-like nanocomposite of reduced graphene oxide (rGO)-supported N-doped carbon embedded with ultrasmall CoNiS x nanocrystallites (rGO/CoNiS x /N-C nanocomposite) has been successfully designed and synthesized by a simple one-step carbonization/sulfurization treatment of the rGO/Co-Ni precursor. The intriguing structural/compositional/morphological advantages endow the as-synthesized rGO/CoNiS x /N-C nanocomposite with excellent electrochemical performance as an advanced electrode material for supercapacitors. Compared with the other two rGO/CoNiO x and rGO/CoNiS x nanocomposites, the rGO/CoNiS x /N-C nanocomposite exhibits much enhanced performance, including a high specific capacitance (1028.2 F g -1 at 1 A g -1 ), excellent rate capability (89.3% capacitance retention at 10 A g -1 ) and good cycling stability (93.6% capacitance retention over 2000 cycles). In addition, an asymmetric supercapacitor (ASC) device based on the rGO/CoNiS x /N-C nanocomposite as the cathode and activated carbon (AC) as the anode is also fabricated, which can deliver a high energy density of 32.9 W h kg -1 at a power density of 229.2 W kg -1 with desirable cycling stability. These electrochemical results evidently indicate the great potential of the sandwich-like rGO/CoNiS x /N-C nanocomposite for applications in high-performance supercapacitors.

Textures and trace element composition of pyrite from the Bukit Botol volcanic-hosted massive sulphide deposit, Peninsular Malaysia

NASA Astrophysics Data System (ADS)

Basori, Mohd Basril Iswadi; Gilbert, Sarah; Large, Ross Raymond; Zaw, Khin

2018-06-01

The Bukit Botol volcanic-hosted massive sulphide (VHMS) deposit is located in the Central Belt of Peninsular Malaysia. The deposit occurs in a package of Permian-aged coherent felsic volcanic and volcaniclastic rocks which have a geochemical signature indicative of a volcanic arc tectonic setting. Mineralisation shows distinct ore zonation, forming a stringer to massive sulphide zone at the footwall followed by barite lenses and exhalite layers (Fe-Mn ore) at the top. Mineralogy is characterised by pyrite as the major sulphide mineral, with minor chalcopyrite, sphalerite, and rare galena; traces of gold, silver- and tin-bearing minerals also occur in the massive sulphide and barite ores. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analysis combined with the textural characteristics of pyrite provides evidence for significant variations of trace elements in different pyrite types at Bukit Botol, having three types of pyrite in the paragenetic sequence. The concentrations of As, Se, Te, Cu, Zn and Pb decrease from the early pyrite 1 to the late stage pyrite 3, and the Co/Ni ratios vary for the three pyrite types. The combined textural and compositional data of pyrite suggest that the hydrothermal fluid responsible for mineralisation evolved from an early, high temperature, reduced, low pH and desulphurized fluid to more S-rich, oxidized, high pH and cooler fluid. Available sulphur isotope data from the Bukit Botol deposit point to reduced seawater, along with a possible magmatic contribution, as the most probable sources for the ore-forming fluids.

Understanding and Exploration of the Biomineralization Mechanisms for the Controllable Synthesis of Nanomaterials

NASA Astrophysics Data System (ADS)

Xiao, Junwu

This thesis is mainly concerned with understanding the biomineralization mechanisms, and further extrapolating them for the controllable synthesis of transition metal compound nanomaterials on graphene sheets for energy storage applications in electrochemical capacitors and lithium ion batteries (LIB). Firstly, we have studied the mimetic biomineralization process of CaCO 3 on a stearic acid or 1,2-dipalmitoyl-sn-glycero-3-phosphatidylcholine (DPPC) Langmuir monolayer at the air-water interface by in-situ Brewster angle microscopy (BAM) and ex-situ electron microscopy. Amorphous calcium carbonate (ACC) precursors are directly nucleated from solvated ions prior to the crystal nuclei on a Langmuir monolayer. On a DPPC monolayer, numerous fresh ACC nanoparticles heterogeneously and continuously nucleated at the air-water interface are transformed into the metastable vaterite nanocrystals. Driven by the trend to decrease surface energy, the vaterite nanocrystals self-aggregate and grow into the loose-packed hollow ellipsoidal vaterite polycrystals. These nanocrystals in vaterite polycrystals are then gradually orientated in the same direction to evolve into tight-packed ellipsoidal mesocrystals. As the crystallization time is further increased, the metastable vaterite mesocrystals are eventually transformed into the most thermodynamically stable calcite crystals. Secondly, organic and inorganic additives control over the shapes, sizes and phases of inorganic nanocrystals and arrange them into ordered structures from amorphous precursors in the organisms. This interesting phenomenon has galvanized many attempts to mimic the biomineralization process for synthesizing novel materials. We have studied the crystallization processes from small citrate molecules stabilized ACC precursors under cetyltrimethyl ammonium bromide (CTAB) micellar structures. Amorphous precursors, with a hydrated and disordered structure, are easily transformed and molded into CaCO 3 crystals with novel morphologies, such as, hollow radiating cluster-like particles, hollow sheaf-like crystals, and hollow rods, which are depended on CTAB micellar structures. Besides organic additives, inorganic dopants, such as, Mg2+ ion, are found to be another key factor to influence the polymorph and morphology. We combine two types of additives (Mg 2+ ion and a denatured collagen protein (gelatin)) to direct the mineralization of CaCO3. The polymorphs and morphologies critically depend on gelatin concentration at a given Mg2+ concentration. While, at a given gelatin concentration, the Mg molar percentages in the mother solution, although not a determining factor for the polymorphs, can affect the crystal micro- and nano-structures. The controlled crystallization can be rationalized by the interplay between Mg2+ and gelatin, which mutually enhances their uptake and regulate the concomitant mineralization. The biomineralization process can be divided into the nucleation of amorphous precursors and the subsequent amorphous to crystalline transformation. Thirdly, on the basis of understanding the biomineralization mechanisms discussed above, we extrapolate it to synthesize transition metal compound nanomaterials on graphene sheets for energy storage application. We have applied a bio-inspired approach to prepare CoxNi1-xO (0≤x<1) nanorods on graphene sheets, breaking out the Co/Ni molar ratio limitation for the known stable mixed oxide spinel NiCo2O4. This success has allowed us to further screen the compositions for electrochemical capacitor. CoxNi1-xO/graphene composite electrodes achieve a peak specific capacitance as the Co/Ni molar ratio is closed to 1. This bio-inspired approach also is applied for anchoring Ni(OH)2 nanocrystals on graphene sheets. The size and morphology of the Ni(OH)2 nanocrystals can be controlled via altering the treated temperature during the Ostwald ripening process. The specific capacitance decreased with increasing Ni(OH) 2 nanocrystal size, whereas the cycling stability performance increased with increasing the stability of Ni(OH)2 in the nanocomposites. (Abstract shortened by UMI.)

Lindqvist Polyoxoniobate Ion-Assisted Electrodeposition of Cobalt and Nickel Water Oxidation Catalysts.

PubMed

Liu, YuPing; Guo, Si-Xuan; Ding, Liang; Ohlin, C André; Bond, Alan M; Zhang, Jie

2015-08-05

A method has been developed for the efficient electrodeposition of cobalt and nickel nanostructures with the assistance of the Lindqvist ion [Nb6O19](8-). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Raman spectroscopy, inductively coupled plasma mass spectrometry (ICP-MS), inductively coupled plasma optical emission spectrometry, and a range of electrochemical techniques have been used to characterize the morphology, composition, catalytic water oxidation activity and stability of the films in alkaline solution. SEM images show that films consisting of nanoparticles with diameters of ca. 30 to 40 nm are formed after 40-50 potential cycles of deposition. Nb and Co/Ni are detected in the films by EDX. ICP-MS results show an elemental ratio of 1:1 for Co:Nb and 1:3 for Ni:Nb, respectively. Raman spectra reveal the presence of both [Nb6O19](8-) and Co(OH)2/Ni(OH)2. The films exhibit excellent stability and efficiency for electrocatalytic water oxidation in alkaline solution. Turnover frequencies of 12.9 and 13.2 s(-1) were determined by rotating ring disk electrode voltammetry at an overpotential of 480 mV for Co and Ni films, respectively. Fourier transformed large amplitude alternating current (FTAC) voltammetry reveals an additional underlying oxidation process for Co under catalytic turnover conditions, which indicates that a Co(IV) species is involved in the efficient catalytic water oxidation reactions. FTAC voltammetric data also suggest that the Ni films undergoes a clear phase transformation upon aging in aqueous 1 M NaOH and the electrogenerated higher oxidation state Ni from β-NiOOH is the more active form of the catalyst.

Structural, magnetic and spectral properties of Gd and Dy co-doped dielectrically modified Co-Ni (Ni0.4Co0.6Fe2O4) ferrites

NASA Astrophysics Data System (ADS)

Ditta, Allah; Khan, Muhammad Azhar; Junaid, Muhammad; Khalil, R. M. Arif; Warsi, Muhammad Farooq

2017-02-01

Gadolinium (Gd) and Dysprosium (Dy) co-doped Ni-Co (Ni0.4Co0.6Fe2O4) ferrites were prepared by micro-emulsion route. X-ray diffraction (XRD) analysis indicated the development of cubic spinel structure. The lattice parameter and X-ray density were found to increase from 8.24 to 8.31 Å and 5.57 to 5.91 (gm/cm3) respectively as the Gd-Dy contents increased in nickel-cobalt ferrites. The crystallite size calculated from the Scherrer's formula exhibited the formation of nanocrystalline ferrites (13-26 nm). Two foremost absorption bands observed in FTIR spectra within 400 cm-1 (υ2) to 600 cm-1 (υ1) which correspond to stretching vibrations of tetrahedral and octahedral complexes respectively. The dielectric constant (ε) and dielectric loss (tanδ) were decreased by the optimization of frequency and abrupt decrease in the low frequency region and higher values in the high frequency region were observed. The dielectric dispersion was due to rapid decrease of dielectric constant in the low frequency region. This variation of dielectric dispersion was explicated in the light of space charge polarization model of Maxwell-Wagner. The dielectric loss occurs in these ferrites due to electron hopping and defects in the dipoles. The electron hopping was possible at low frequency range but at higher frequency the dielectric loss was decreased with the decrease of electron hopping. Magnetic properties were observed by measuring M-H loops. Due to low dielectric loss and dielectric constant these materials were appropriate in the fabrication of switching and memory storage devices.

Effects of Mg substitution on the structural and magnetic properties of Co0.5Ni0.5-x Mg x Fe2O4 nanoparticle ferrites

NASA Astrophysics Data System (ADS)

R, M. Rosnan; Z, Othaman; R, Hussin; Ali, A. Ati; Alireza, Samavati; Shadab, Dabagh; Samad, Zare

2016-04-01

In this study, nanocrystalline Co-Ni-Mg ferrite powders with composition Co0.5Ni0.5-x Mg x Fe2O4 are successfully synthesized by the co-precipitation method. A systematic investigation on the structural, morphological and magnetic properties of un-doped and Mg-doped Co-Ni ferrite nanoparticles is carried out. The prepared samples are characterized using x-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM), and vibrating sample magnetometry (VSM). The XRD analyses of the synthesized samples confirm the formation of single-phase cubic spinel structures with crystallite sizes in a range of ˜ 32 nm to ˜ 36 nm. The lattice constant increases with increasing Mg content. FESEM images show that the synthesized samples are homogeneous with a uniformly distributed grain. The results of IR spectroscopy analysis indicate the formation of functional groups of spinel ferrite in the co-precipitation process. By increasing Mg2+ substitution, room temperature magnetic measurement shows that maximum magnetization and coercivity increase from ˜ 57.35 emu/g to ˜ 61.49 emu/g and ˜ 603.26 Oe to ˜ 684.11 Oe (1 Oe = 79.5775 A·m-1), respectively. The higher values of magnetization M s and M r suggest that the optimum composition is Co0.5Ni0.4Mg0.1Fe2O4 that can be applied to high-density recording media and microwave devices. Project supported by the Ibnu Sina Institute for Scientific and Industrial Research, Physics Department of Universiti Teknologi Malaysia and the Ministry of Education Malaysia (Grant Nos. Q.J130000.2526.04H65).

Comparative study of electroless Co-Ni-P plating on Tencel fabric by Co0-based and Ni0-based activation for electromagnetic interference shielding

NASA Astrophysics Data System (ADS)

Bi, Siyi; Zhao, Hang; Hou, Lei; Lu, Yinxiang

2017-10-01

The primary objective of this research work was to develop high-performance conductive fabrics with desired electromagnetic interference (EMI) shielding effectiveness (SE), excellent durability and improved corrosion resistance. Such conductive fabrics were fabricated by combining an ultra-low-cost electroless plating method with an alkoxy silane self-assembly technology, which involved successive steps of modification, activation, Co-Ni-P coating deposition and 3-aminopropyltrimethoxysilane (APTMS) thin coatings assembling. Malic acid (MA) was selected to modify the pristine Tencel (TS) substrates, and the probably interaction mechanism was investigated by FT-IR measurement. Co0 and Ni0 nanoparticles (NPs) were used as the activators to initiate electroless plating, respectively, and thereby two categories of Co-Ni-P coatings with different Co/Ni atomic ratio were obtained. Both of them presented compact morphologies and preferential (1 1 1) crystal orientation, which were validated by FE-SEM and XRD measurements. Owing to the lower square resistance and higher magnetic properties, the Co-Ni-P coated fabric activated by Co0 activator showed a higher EMI SE (18.2-40.1 dB) at frequency of 30-1000 MHz. APTMS thin coatings were then assembled on the top of alloy coated fabrics to act as anti-corrosion barriers. Electrochemical polarization measurement in 3.5 wt.% NaCl solution showed that top-APTMS coated conductive fabric exhibited a higher corrosion resistance than the one in absence of APTMS assembly. Overall, the whole process of fabrication could be performed in several hours (or less) without any specialized equipment, which shows a great potential as EMI shielding fabrics in mass-production.

The Nickel(111)/Alkaline Electrolyte Interface

NASA Technical Reports Server (NTRS)

Wang, Kuilong; Chottiner, G. S.; Scherson, D. A.; Reid, Margaret A.

1991-01-01

The electrochemical properties of Ni (111) prepared and characterized in ultra high vacuum, UHV, by surface analytical techniques have been examined in alkaline media by cyclic voltammetry using an UHV-electrochemical cell transfer system designed and built in this laboratory. Prior to the transfer, the Ni(111) surfaces were exposed to saturation coverages of CO in UHV in an attempt to protect the surface from possible contamination with other gases during the transfer. Temperature Programmed Desorption, TPD, of CO-dosed Ni (111) surfaces displaying sharp c(4x2), LEED patterns, subsequently exposed to water-saturated Ar at atmospheric pressure in an auxiliary UHV compatible chamber and finally transferred back to the main UHV chamber, yielded CO2 and water as the only detectable products. This indicates that the CO-dosed surfaces react with water and/or bicarbonate and hydroxide as the most likely products. Based on the integration of the TPD peaks, the combined amounts of H2O and CO2 were found to be on the order of a single monolayer. The reacted c(4x2)CO/Ni(111) layer seems to protect the surface from undergoing spontaneous oxidation in strongly alkaline solutions. This was evidenced by the fact that the open circuit potential observed immediately after contact with deaerated 0.1 M KOH was about 0.38 V vs. DHE, drifting slightly towards more negative values prior to initiating the voltametric scans. The average ratio of the integrated charge obtained in the first positive linear scan in the range of 0.35 to 1.5 V vs. DHE (initiated at the open circuit potential) and the first (and subsequent) linear negative scans in the same solution yielded for various independent runs a value of 3.5 +/- 0.3. Coulometric analysis of the cyclic voltammetry curves indicate that the electrochemically formed oxyhydroxide layer involves a charge equivalent to 3.2 +/- 0.4 layers of Ni metal.

Métastase pleurale et pulmonaire d’une polyadénofibromatose dégénéréé: à propos d’un cas

PubMed Central

El Hachimi, Kawtar; Benjelloun, Hanane; Zaghba, Nahid; Yassine, Najiba

2017-01-01

La polyadénofibromatose ou l’adénofibromatose est définie par la présence d’au moins 3 adénofibromes, uni ou bilatéraux atteignant une taille importante responsable de troubles trophiques. Nous rapportons une observation colligée au service des maladies respiratoires du Centre Hospitalier Universitaire Ibn Rochd de Casablanca. Il s’agit d’une patiente âgée de 46ans, suivie depuis l’âge de 30 ans pour une adénofibromatose bilatérale opérée à 4 reprises. Suite à un bilan préopératoire d’une mastectomie bilatérale, une radio du thorax a été réalisée objectivant un hémithorax droit opaque avec refoulement des éléments du médiastin. L’examen clinique retrouvait un syndrome d’épanchement liquidien de l’hémithorax droit et une adénopathie cervicale sus claviculaire gauche. La ponction biopsie pleurale confirmait la localisation pleurale d’un carcinome peu différencié et invasif compatible avec une origine mammaire. La bronchoscopie après évacuation pleurale objectivait un aspect infiltré de tout l’arbre bronchique, dont les biopsies concluaient au même résultat anatomopathologique. Le traitement préconisé était une polychimiothérapie. L’évolution était marquée par l’apparition de métastases hépatiques. A travers cette observation, nous concluons que les adénofibromes nécessitent une surveillance régulière vu le risque de dégénérescence vers le cancer du sein qui est une cause fréquente de métastases pleuropulmonaires. PMID:29515733

M(2)C Carbide Precipitation in Martensitic Cobalt - Steels.

NASA Astrophysics Data System (ADS)

Montgomery, Jonathan Scott

1990-01-01

M_2C carbide precipitation was investigated in martensitic Co-Ni steels, including the commercial AF1410 steel and a series of higher-strength model alloys. Results of TEM (from both thin foils and extraction replicas) and X-ray diffraction were combined with results of collaborative SANS and APFIM studies to determine phase fractions, compositions, and lattice parameters throughout precipitation, including estimation of carbide initial critical nucleus properties. The composition dependence of the M_2C lattice parameters was modelled to predict the composition-dependent transformation eigen-strains for coherent precipitation; this was input into collaborative numerical calculations of both the coherent carbide elastic self energy and the dislocation interaction energy during heterogeneous precipitation. The observed overall precipitation behavior is consistent with theoretically-predicted behavior at high supersaturations where nucleation and coarsening compete such that the average particle size remains close to the critical size as supersaturation drops. However, the coarsening in this system follows a t^{1over 5} rate law consistent with heterogeneous precipitation on dislocations. Initial precipitation appears to be coherent, the carbides tending toward a rod shape with major axis oriented along the minimum principal strain direction. At initial nucleation, particles are Fe-rich and C-deficient, diminishing the transformation eigenstrains to a near invariant-line strain condition. The observed relation between carbide volume fraction and the shape -dependent capillarity parameter partialS/ partialV implies a coherency loss transition in AF1410 reached at 8hr tempering at 510 ^circC. The precipitation in AF1410 at 510^ circC exhibits a "renucleation" phenomenon in which a second stage of nucleation occurs beyond the precipitation half-completion time (1-2hrs). It appears that the carbide composition during precipitation follows a trajectory of increasing interfacial energy and nearly constant volume driving force. This may contribute to the renucleation phenomenon, but the computed barrier for heterogeneous nucleation on the dislocations is at this point an order of magnitude too high. An alternative possibility is that renucleation may represent autocatalytic heterogeneous nucleation in the stress field of coherent carbides, once they have grown to sufficient size to act as potent nucleation sites.

Effects and quantification of acid runoff from sulfide-bearing rock deposited during construction of Highway E18, Norway

USGS Publications Warehouse

Hindar, Atle; Nordstrom, D. Kirk

2015-01-01

The Highway E18 between the cities of Grimstad and Kristiansand, southern Norway, constructed in the period 2006–2009, cuts through sulfide-bearing rock. The geology of this area is dominated by slowly-weathering gneiss and granites, and oxidation of fresh rock surfaces can result in acidification of surface water. Sulfide-containing rock waste from excavations during construction work was therefore deposited in three waste rock deposits off-site. The deposits consist of 630,000–2,360,000 metric tons of waste rock material. Shell sand and limestone gravel were added in layers in adequate amounts to mitigate initial acid runoff in one of the deposits. The shell sand addition was not adequate in the two others. The pH in the effluents from these two was reduced from 4.9–6.5 to 4.0–4.6, and Al concentrations increased from below 0.4 mg/L to 10–20 mg/L. Stream concentrations of trace metals increased by a factor of 25–400, highest for Ni, and then in decreasing order for Co, Mn, Cd, Zn and Cu. Concentrations of As, Cr and Fe remained unchanged. Ratios of Co/Ni and Cd/Zn indicate that the metal sources for these pair of metals are sphalerite and pyrite, respectively. Based on surveys and established critical limits for Al, surface waters downstream became toxic to fish and invertebrates. The sulfur release rates were remarkably stable in the monitoring period at all three sites. Annual sulfur release was 0.1–0.4% of the total amount of sulfur in the deposit, indicating release periods of 250–800 years. Precipitates of Al-hydroxysulfates, well-known from mining sites, were found at the base of the deposits, in streams and also along the ocean shore-line. The effects of added neutralization agents in the deposits and in treatment areas downstream gradually decreased, as indicated by reduced stream pH over time. Active measures are needed to avoid harmful ecological effects in the future.

Textures and compositions of cobalt pentlandite and cobaltian mackinawite from the Madan-Kudan copper deposit, Khetri Copper Belt, Rajasthan, India

NASA Astrophysics Data System (ADS)

Baidya, Abu Saeed; Sen, Atlanta; Pal, Dipak C.

2018-06-01

The Khetri Copper Belt (KCB), a part of the Proterozoic Delhi-Aravalli fold belt in western India, hosts several Cu deposits, which are known to contain considerable Au, Ag, Co and Ni. Although many Co-bearing phases have been reported from the KCB and adjacent areas, detailed textural and geochemical data are either unavailable or scant except for mackinawite. In this study, we describe the textures and compositions (determined by EPMA) of two very rare Co-rich phases, namely cobaltian mackinawite (containing up to 12.68 wt.% Co, 1.90 wt.% Ni and 2.52 wt.% Cu) and cobalt-pentlandite (containing up to 49.30 wt.% Co and 10.19 wt.% Ni), identified based on composition, from the Madan-Kudan deposit. To the best of our knowledge, neither cobalt-pentlandite nor such highly Co-rich mackinawite have previously been reported from this area. The common sulphide minerals viz. chalcopyrite, pyrrhotite and rare pyrite occur in chalcopyrite-pyrrhotite ± pyrite-magnetite-chlorite-blue amphibole (Cl-rich hastingsite-pargasite-sadanagaite) ± marialitic scapolite ± allanite ± uraninite veins in amphibole-bearing feldspathic quartzite and garnetiferous chlorite schist. Cobaltian mackinawite is invariably associated with chalcopyrite and occurs as exsolution and inclusion within chalcopyrite or outside, but at the contact of chalcopyrite. On the other hand, cobalt-pentlandite is invariably associated with pyrrhotite and shows similar textural relation with pyrrhotite as that of mackinawite with chalcopyrite. Mineralogically diverse undeformed sulphide veins comprising Cl-rich amphibole and locally Cl-rich marialitic scapolite suggests epigenetic hydrothermal mineralization involving Cl-rich saline fluid in the Madan-Kudan deposit. Transport of metals, derived from a mafic source rock with high intrinsic Ni:Co ratio, by Cl-rich fluid can suitably explain the high Co:Ni ratio of the studied ore minerals. Presence of such highly Co-rich phases and other circumstantial evidences, enumerated in this work, are consistent with variants of Fe oxide (-Cu-Au) (IOCG) style mineralization, at least for some stages of mineralization in the Madan-Kudan deposit.

Electrical, Magnetic and Microwave Absorption Properties of M-type Barium Hexaferrites (BaFe12-2x CoxNixO19)

NASA Astrophysics Data System (ADS)

Susilawati; Doyan, A.; Khair, H.; Taufik, M.; Wahyudi

2018-04-01

M-type barium hexaferrites synthesis with Co-Ni doping ion (BaFe12-2x CoxNixO19) based on natural iron sand of Loang Balok beach, Lombok, Indonesia, to be applied as a microwave absorbent material using co-precipitation method. The materials used in the synthesis process are magnetite minerals (Fe2O3 and Fe3O4), 12M HCl, NH4OH 37%, CoCl2.6H2O and NiCl2.6H2O. This research to investigate the effect of doping ion concentration variation (x = 0.0, 0.6 and 1.0) and calcination temperature (T = 80, 600, and 800°C) on electrical and magnetic properties and microwave absorption as well. The samples were characterized using Vibrating Sample Magnetometer (VSM) and Network Vector Analyzer (VNA). The result from VSM showed that the coercivity value decreased when doping ion concentration and calcination temperature increased (0.151 Tesla at 600°C for x = 0.0 and 0.044 Tesla at 800°C for x = 1.0. The value of magnetic saturation and the magnetic remanence increased with increasing ion concentration (Ms = 0.327 emu/g at x = 0.0 increased to 35.4 emu/g at x = 1.0) and Mr = 0.148 emu/g for x = 0.0 increased to 15.6 emu/g at x=1.0, this indicates that the sample has been soft magnetic. The result from VNA showed that the electrical conductivity values measured in the range 8.0-15.0 GHz indicate that the sample is a semiconductor (6.149 x 10-6 -5.975 x 10-4 S/cm). It also showed that the microwave absorption properties increased at higher concentration of doping ions and the calcination temperature would increase the value of Reflection Loss (RL). The maximum RL value of the sample is -14.47 dB at 12.38 GHz, and the absorption coefficient of 96.43%. These results indicate that the BaFe12-2x CoxNixO19 sample can be applied as a microwave absorbent material on X-band to Ku-band frequency.

A three body problem: a genuine heterotrimetallic molecule vs. a mixture of two parent heterobimetallic molecules.

PubMed

Han, Haixiang; Wei, Zheng; Barry, Matthew C; Carozza, Jesse C; Alkan, Melisa; Rogachev, Andrey Yu; Filatov, Alexander S; Abakumov, Artem M; Dikarev, Evgeny V

2018-06-07

This work raises a fundamental question about the "real" structure of molecular compounds containing three different metals: whether they consist of genuine hetero tri metallic species or of a mixture of parent hetero bi metallic species. Heterotrimetallic complex Li 2 CoNi(tbaoac) 6 ( 1 , tbaoac = tert -butyl acetoacetate) has been designed based on the model tetranuclear structure featuring two transition metal sites in order to be utilized as a molecular precursor for the low-temperature preparation of the LiCo 0.5 Ni 0.5 O 2 battery cathode material. An investigation of the structure of 1 appeared to be very challenging, since the Co and Ni atoms have very similar atomic numbers, monoisotopic masses, and radii as well as the same oxidation state and coordination number/environment. Using a statistical analysis of heavily overlaid isotope distribution patterns of the [Li 2 MM'L 5 ] + (M/M' = Co 2 , Ni 2 , and CoNi) ions in DART mass spectra, it was concluded that the reaction product 1 contains both heterotrimetallic and bimetallic species. A structural analogue approach has been applied to obtain Li 2 MMg(tbaoac) 6 (M = Co ( 2 ) and Ni ( 3 )) complexes that contain lighter, diamagnetic magnesium in the place of one of the 3d transition metals. X-ray crystallography, mass spectrometry, and NMR spectroscopy unambiguously confirmed the presence of three types of molecules in the reaction mixture that reaches an equilibrium, Li 2 M 2 L 6 + Li 2 Mg 2 L 6 ↔ 2Li 2 MMgL 6 , upon prolonged reflux in solution. The equilibrium mixture was shown to have a nearly statistical distribution of the three molecules, and this is fully supported by the results of theoretical calculations revealing that the stabilization energies of hetero tri metallic assemblies fall exactly in between those for the parent hetero bi metallic species. The LiCo 0.5 Ni 0.5 O 2 quaternary oxide has been obtained in its phase-pure form by thermal decomposition of heterometallic precursor 1 at temperatures as low as 450 °C. Its chemical composition, structure, morphology, and transition metal distribution have been studied by X-ray and electron diffraction techniques and compositional energy-dispersive X-ray mapping with nanometer resolution. The work clearly illustrates the advantages of heterometallic single-source precursors over the corresponding multi-source precursors.

Co/Ni ratios at taenite/kamacite interfaces and relative cooling rates in iron meteorites

NASA Astrophysics Data System (ADS)

Wasson, John T.; Hoppe, Peter

2012-05-01

We report a pilot study of a new technique to use the distribution of Co between kamacite and taenite to infer relative cooling rates of iron meteorites; data of Widge and Goldstein (1977) showed that the distribution is temperature dependent. A plot of the logarithm of the double ratio [(Co/Ni)kamacite/(Co/Ni)taenite] (abbreviated Rαγ) against inverse temperature yields a linear equation showing that the ratio ranges from ˜2.5 at 1080 K to ˜30 at 710 K. Thus, a measurement of Rαγ in the kamacite and taenite near the interface offers information about relative cooling rates; the higher Rαγ, the lower the cooling rate. A major advantage of this technique is that it is mainly affected by the final (low-temperature) cooling rate, just before the sample cooled to the blocking temperature where diffusion became insignificant. To test this method we used the NanoSIMS ion probe to measure Rαγ in two IVA and two IIIAB irons; members of each pair differ by large factors in elemental composition and in published metallographic cooling rates (Yang and Goldstein, 2006; Yang et al., 2008). Despite differing by a factor of 25 in estimated metallographic cooling rate, the two IVA irons showed similar Rαγ values of ˜22. If experimental uncertainties are considered this implies that, at low temperatures, their cooling rates differ by less than a factor of 5 with 95% confidence, i.e., significantly less than the range in metallographic cooling rates. In contrast, the IIIAB irons have different ratios; Rαγ in Haig is 29 whereas that in Cumpas, with a reported cooling rate 4.5 times lower, is 22, the opposite of that expected from the published cooling rates. A reevaluation of the Yang-Goldstein IIIAB data set shows that Haig has anomalous metallographic properties. We suggest that both the high Rαγ in Haig and the systematically low taenite central Ni contents are the result of impact-produced fractures in the taenite that allowed equilibration with kamacite down to lower temperatures but shut down Ni transport to the interiors of taenite lamellae. Our observations of similar Rαγ values in IVA irons differing by a factor of 25 in metallographic cooling rates implies that there was, in fact, only a comparatively small difference in low-temperature cooling rates in IVA irons; because we studied only two IVA irons, this conclusion will remain tentative until further studies can be completed.

Lésions bulleuses et purpuriques unilatérales: pathomimie cutanée

PubMed Central

Zinoun, Mouna; Chiheb, Soumia; Marnissi, Farida; Kadiri, Nadia; Benchikhi, Hakima

2015-01-01

La pathomimie cutanée est une forme particulière de troubles factices relativement rare, et constitue l'un des problèmes les plus complexes pour le dermatologue. Nous rapportons un cas de pathomimie révélée par des lésions cutanées unilatérales, mimant une brûlure. Une jeune femme de 27 ans, était suivie depuis 4 ans pour une dépression. Elle a présenté 15j avant sa 1ère hospitalisation un placard inflammatoire du sein gauche compliqué de lésions bulleuses et d’érosions superficielles. La biopsie cutanée avait montré une dermite non spécifique. Une cicatrisation rapide sous traitement local a été notée. Elle a présenté 10 jours plus tard de nouvelles lésions similaires étagées au membre inférieur gauche, évoluant vers le décollement bulleux spontané. La biopsie cutanée avait montré un décollement bulleux jonctionnel et des foyers de nécrose ischémique. L'IFD était négative. Devant les données anamnestiques, cliniques, la négativité du bilan paraclinique, et la guérison des lésions sous pansements occlusifs seuls, le diagnostic de pathomimie a été évoqué et retenu. La patiente a été adressée en psychiatrie où une thérapie cognitivo-comportementale a été préconisée. Notre observation correspond à un tableau de pathomimie de présentation clinique particulière par sa localisation unilatérale et son caractère bulleux. Chez notre patiente qui est droitière, la localisation unilatérale gauche sur des zones accessibles, l'absence de lésions spécifiques à l'examen histologique, la cicatrisation rapide des lésions sous traitement local occlusif seul et leur récurrence malgré des soins adaptés étaient en faveur d'une pathologie factice. Néanmoins, la localisation au niveau des seins peut être très déroutante. Le caractère bulleux des lésions dans le cadre d'une pathomimie a été rarement rapporté. Dans notre cas, la pathomimie s'associe à des troubles anxieux et dépressifs très importants. Leur prise en charge demande un investissement pluridisciplinaire le plus précoce possible. La prise en charge des pathomimies est complexe. Le traitement médical associé à une prise en charge psychologique de type thérapie cognitivo-comportementale, qui est une première expérience, peut aider cette patiente à contrôler son comportement et éviter les récidives qui sont fréquentes dans ce type de pathologie. PMID:26161224

The geochemistry of carbonatites revisited: Two major types of continental carbonatites and their trace-element signatures

NASA Astrophysics Data System (ADS)

Chakhmouradian, A.

2009-04-01

There have been several attempts to systematize the geochemistry of carbonatites, most recently by Samoilov (1984), Nelson et al. (1988), Woolley and Kempe (1989), and Rass (1998). These studies revealed a number of important geochemical characteristics that can be used to track the evolutionary history of these rocks, distinguish them from modally similar metamorphic parageneses, and aid in mineral exploration for rare earths, niobium and other resources commonly associated with carbonatites. Important breakthroughs in the understanding of carbonatite petrogenesis and numerous reports of new carbonatite localities made in the past two decades lay the ground for a critical re-assessment of the geochemistry of these rocks. A new representative database of whole-rock carbonatite analyses was compiled from the post-1988 literature and various unpublished sources. The database contains 820 analyses encompassing calcio-, magnesio- and ferrocarbonatites from 174 localities (ca. one-third of the total number of carbonatites known worldwide) reduced to ca. 350 analyses following the approach of Woolley and Kempe (1989). Carbonatites emplaced in oceanic settings (e.g., Cape Verde), ophiolite belts (e.g., Oman), or those of uncertain tectonic affinity (e.g., El Picacho in Mexico) were not included. Two major types of continental carbonatites can be distinguished on the basis of their geological setting and trace-element geochemistry: (1) carbonatites emplaced in rifts and smaller-scale extensional structures developed in stable Archean cratons or paleo-orogenic belts, and (2) carbonatites emplaced in collisional settings following the orogenesis. In both settings, the most common and best-studied type of carbonatite is calcite carbonatite (predominantly intrusive with a small percentage of extrusive occurrences), which accounts for 62% of the analyses included in the database. Both types of carbonatite are typically associated with alkaline silicate lithologies (meleigites, nepheline syenites, etc.), but those associated with type-1 rocks are typically Na-rich and silica-undersaturated, whereas type-2 carbonatites are associated with K-rich silica-saturated to undersaturated syenites. Type-1 carbonatites are notably different from their type-2 counterparts in showing higher abundances of high-field-strength elements (HFSE = Ti, Zr, Hf, Nb, Ta), Rb, U and V, but lower levels of Sr, Ba, Pb, rare-earth elements, F and S. Key element ratios are also different in the two carbonatite types; in particular, Rb/K, Nb/Ta, Zr/Hf and Ga/Al values are consistently higher in type-1 samples. Notably, some element ratios (e.g., Co/Ni and Y/Ho) are very similar in both groups. Type-2 carbonatites commonly show a 13C-depleted signature relative to the "primary carbonatite" range (Deines, 1989). The observed differences in geological setting and geochemistry indicate the existence of two distinct carbonatite sources in the subcontinental lithosphere: amphibole-bearing lherzolite producing type-1 rocks (cf. Chakhmouradian, 2006), and subducted oceanic crust (rutile-bearing eclogite?) yielding type-2 melts depleted in HFSE, but enriched in light carbon, large-ion-incompatible elements, F and S. References: Chakhmouradian, A.R. (2006) High-field-strength elements in carbonatitic rocks: Geochemistry, crystal chemistry and significance for constraining the sources of carbonatites. Chem. Geol., 235, 138-160. Deines, P. (1989) Stable isotope variations in carbonatites. In: Carbonatites: Genesis and Evolution (K. Bell, Ed.). Unwin Hyman, London, 301-359. Nelson, D.R., Chivas, A.R., Chappell, B.V. and McCulloch, M.T. (1988) Geochemical and isotopic systematic in carbonatites and implications for the evolution of ocean-island sources. Geochim. Cosmochim. Acta, 52, 1-17. Rass, I.T. (1998) Geochemical features of carbonatite indicative of the composition, evolution, and differentiation of their mantle magmas. Geochem. Int., 36, 107-116. Samoilov, V.S. (1984) Geochemistry of Carbonatites. Nauka, Moscow (in Russ.). Woolley, A.R. and Kempe, D.R.C. (1989) Carbonatites: nomenclature, average chemical compositions, and element distribution. In: Carbonatites: Genesis and Evolution (K. Bell, Ed.). Unwin Hyman, London, 1-14.

Estimation of the Cost of Equity for Mining Companies Using the P-Lefac Method

NASA Astrophysics Data System (ADS)

Ranosz, Robert

2014-03-01

This article describes one of the methods of estimating the cost of equity, namely the LEFAC method. The name of the method is an acronym of the names of individual financial categories: L - Liquidity, E - Earnings, F - Franchise, A - Assets, C - Capital. It is a scoring method similar to the way used by ING Financial Markets to estimate share prices. A review of literature shows that this method is not widely known and used by enterprises, but it has certain advantages which justify its use. Its main advantages include its easy use and the stability of the results obtained: the calculated cost of equity is never lower than the adopted risk-free rate. The method is particularly useful for companies (enterprises) not listed on stock exchanges. This article is divided into five parts: an introduction, the LEFAC method, the parameterization of the LEFAC method (P-LEFAC), an example calculation and a summary. The second part of this article characterises the LEFAC method. In the third part, the method is parameterized to obtain a function described by formula 22. The following section contains an example calculation for KGHM S.A. and also presents results which mining companies would achieve if they used the discussed method to calculate the cost of their equity. The calculations were performed for mining companies listed on the Warsaw Stocks Exchange and unlisted ones. This part of the article also contains a short comparison of results obtained using the CAPM method and the discussed model. The last section consists of a summary presenting final conclusions. The article ends in a list of the literature referred to. Niniejszy artykuł został poświęcony jednej z metod szacowania kosztu kapitału własnego, a mianowicie metodzie LEFAC. Nazwa metody pochodzi od pierwszych liter wyrazów z języka angielskiego, które określają poszczególne kategorie finansowe: L - Liquidity (płynność), E - Earnings (zyski), F - Franchise (strategia), A - Assets (aktywa), C - Capital (kapitał). Jest to metoda punktowa (scoringowa) zbliżona do sposobu określania wartości cen akcji wykorzystywana przez ING Finansial Markets. Jak wynika z przeprowadzonego przeglądu literatury, metoda ta nie jest powszechnie znana i używania przez przed- siębiorstwa, niemniej jednak posiada ona pewne zalety, uzasadniające jej wykorzystanie. Do jej głównych atutów należy zaliczyć łatwość zastosowania oraz "stabilność" uzyskiwanych wyników - wyliczony koszt kapitału własnego nigdy nie będzie przyjmował wartości mniejszych niż przyjęta stopa wolna od ryzyka. Omawiana metoda ma swoje szczególne zastosowanie do spółek (przedsiębiorstw), które nie są notowane na giełdach papierów wartościowych. Niniejszy artykuł składa się z pięciu części: wstępu, metody LEFAC, parametryzacji metody LEFAC (P-LEFAC), przykładu obliczeniowego oraz podsumowania. Druga cześć opracowania dotyczy charakterystyki metody LEFAC. W trzeciej części artykułu dokonano parametryzacji metody uzyskując funkcję określoną przez wzór 22. Kolejny rozdział zawiera przykład obliczeniowy dla spółki KGHM S.A., w rozdziale tym zaprezentowano również wyniki, jakie uzyskałyby spółki górnicze stosując omawianą metodę obliczania kosztu kapitału własnego - obliczeń dokonano zarówno dla spółek górniczych notowanych, jak i nie notowanych, na Warszawskiej Giełdzie Papierów Wartościowych. W tej części artykułu zaprezentowano również krótkie porównanie wyników uzyskiwanych przy zastosowaniu metody CAPM z omawianym modelem. Ostatnim rozdziałem jest podsumowanie, w którym przedstawiono wnioski końcowe. Całość artykułu została zamknięta spisem wykorzystanej literatury

Prise en charge des traumatismes graves du rein

PubMed Central

Lakmichi, Mohamed Amine; Jarir, Redouane; Sadiki, Bader; Zehraoui; Bentani; Wakrim, Bader; Dahami, Zakaria; Moudouni; Sarf, Ismail

2015-01-01

Les traumatismes graves du rein de grade III, IV et V selon la classification de l'Amercan Society for Surgery For Trauma (ASST) sont plus rares et se retrouvent dans 5% des cas en moyenne. Leur prise en charge est souvent délicate, nécessitant alors des centres expérimentés dotés de moyen adéquats d'imagerie (scanner spiralé). Cependant, durant ces dernières années, la prise en charge de ces traumatismes a évolué vers une attitude de moins en moins chirurgicale grâce à l’évolution des techniques de la radiologie interventionnelle, de l'endourologie et des moyens de surveillance aux urgences et de réanimation. L'objectif de cette étude est d’évaluer notre expérience dans la prise en charge des traumatismes rénaux de haut grade. Notre étude rétrospective porte sur 25 cas de traumatismes grave du rein de grade III, IV et V selon la classification de l'ASST, colligés entre Janvier 2002 et Juin 2009 au service d'urologie du centre Hospitalier Universitaire Mohammed VI, Université Cadi Ayyad de Marrakech, Maroc. Nous avons étudié les données épidémiologiques, les signes cliniques et biologiques à l'admission (état de choc hémorragique, taux d'hémoglobine), les données radiologiques (échographie et scanner), les lésions associées, la prise en charge thérapeutique et les complications. L’âge moyen de nos patients était de 24,9 ans 15 et 58 ans, avec une prédominance masculine (sex-ratio = 7, 3). Le rein droit était intéressé dans 15 cas (60%). Le traumatisme rénal était fermé dans 15 cas, et ouvert par arme blanche dans 10 cas. Huit patients se sont présentés en état de choc hémorragique (32%). Une anémie inférieur à 10g /100ml a été observée dans 10 cas (40%). L'uroscanner fait systématiquement à l'admission a retrouvé un grade III (10 cas), grade IV (13 cas) et grade V (2 cas). La prise en charge a consisté en une exploration chirurgicale avec néphrectomie chez 2 cas de Grade IV pour une instabilité hémodynamique. Une surveillance active clinique, biologique, et radiologique a été préconisée dans 23 cas (92%). Le scanner de contrôle fait à J7, a objectivé une stabilisation des lésions dans 17 cas et la constitution d'un urinome dans 2 cas drainé par sonde double J. Une néphrectomie d'hémostase était nécessaire dans 4 cas de grade IV (3 cas) et de grade V (1 cas). Un patient est décédé à J2 d'un traumatisme ouvert grade IV suite à une hémorragie foudroyante. La durée moyenne d'hospitalisation était de 17 jours (6-75 jours). A travers notre étude, on conforte l'attitude conservatrice recommandée actuellement dans la prise en charge de la plupart des traumatismes graves du rein en l'absence d'une instabilité hémodynamique, grâce aux mesures de réanimation correcte, une surveillance rapprochée du patient et le recours aux moyens endoscopiques de drainage des voies excrétrices. Grace à cette attitude la plupart de nos patients (76%) on conservé leur unités rénales, extrêmement précieuses en particulier pour les patients sujets à la dégradation ultérieure de leur fonction rénale, leur permettant ainsi d’éviter de tomber dans l'hémodialyse ou de rentrer dans des programmes de greffe rénale. PMID:26090064

EBV Chronic Infections

PubMed Central

Eligio, Pizzigallo; Delia, Racciatti; Valeria, Gorgoretti

2010-01-01

The infection from Epstein-Barr virus (EBV) or virus of infectious mononucleosis, together with other herpes viruses’ infections, represents a prototype of persistent viral infections characterized by the property of the latency. Although the reactivations of the latent infection are associated with the resumption of the viral replication and eventually with the “shedding”, it is still not clear if this virus can determine chronic infectious diseases, more or less evolutive. These diseases could include some pathological conditions actually defined as “idiopathic”and characterized by the “viral persistence” as the more credible pathogenetic factor. Among the so-called idiopathic syndromes, the “chronic fatigue syndrome” (CFS) aroused a great interest around the eighties of the last century when, just for its relationship with EBV, it was called “chronic mononucleosis” or “chronic EBV infection”. Today CFS, as defined in 1994 by the CDC of Atlanta (USA), really represents a multifactorial syndrome characterized by a chronic course, where reactivation and remission phases alternate, and by a good prognosis. The etiopathogenetic role of EBV is demonstrated only in a well-examined subgroup of patients, while in most of the remaining cases this role should be played by other infectious agents - able to remain in a latent or persistent way in the host – or even by not infectious agents (toxic, neuroendocrine, methabolic, etc.). However, the pathogenetic substrate of the different etiologic forms seems to be the same, much probably represented by the oxidative damage due to the release of pro-inflammatory cytokines as a response to the triggering event (infectious or not infectious). Anyway, recently the scientists turned their’s attention to the genetic predisposition of the subjects affected by the syndrome, so that in the last years the genetic studies, together with those of molecular biology, received a great impulse. Thanks to both these studies it was possibile to confirm the etiologic links between the syndrome and EBV or other herpesviruses or other persistent infectious agents. The mechanisms of EBV latency have been carefully examined both because they represent the virus strategy to elude the response of the immune system of the host, and because they are correlated with those oncologic conditions associated to the viral persistence, particularly lymphomas and lymphoproliferative disorders. Just these malignancies, for which a pathogenetic role of EBV is clearly documented, should represent the main clinical expression of a first group of chronic EBV infections characterized by a natural history where the neoplastic event aroused from the viral persistence in the resting B cells for all the life, from the genetic predisposition of the host and from the oncogenic potentialities of the virus that chronically persists and incurs reactivations. Really, these oncological diseases should be considered more complications than chronic forms of the illness, as well as other malignancies for which a viral – or even infectious - etiology is well recognized. The chronic diseases, in fact, should be linked in a pathogenetic and temporal way to the acute infection, from whom start the natural history of the following disease. So, as for the chronic liver diseases from HBV and HCV, it was conied the acronym of CAEBV (Chronic Active EBV infection), distinguishing within these pathologies the more severe forms (SCAEBV) mostly reported in Far East and among children or adolescents. Probably only these forms have to be considered expressions of a chronic EBV infection “sensu scrictu”, together with those forms of CFS where the etiopathogenetic and temporal link with the acute EBV infection is well documented. As for CFS, also for CAEBV the criteria for a case definition were defined, even on the basis of serological and virological findings. However, the lymphoproliferative disorders are excluded from these forms and mantain their nosographic (e.g. T or B cell or NK type lymphomas) and pathogenetic collocation, even when they occur within chronic forms of EBV infection. In the pathogenesis, near to the programs of latency of the virus, the genetic and environmental factors, independent from the real natural history of EBV infection, play a crucial role. Finally, it was realized a review of cases - not much numerous in literature – of chronic EBV infection associated to chronic liver and neurological diseases, where the modern techniques of molecular biology should be useful to obtain a more exact etiologic definition, not always possibile to reach in the past. The wide variety of clinical forms associated to the EBV chronic infection makes difficult the finding of a univocal pathogenetic link. There is no doubt, however, that a careful examination of the different clinical forms described in this review should be useful to open new horizons to the study of the persistent viral infections and the still not well cleared pathologies that they can induce in the human host. PMID:21415952

Environmental degradation of oxidation resistant and thermal barrier coatings for fuel-flexible gas turbine applications

NASA Astrophysics Data System (ADS)

Mohan, Prabhakar

The development of thermal barrier coatings (TBCs) has been undoubtedly the most critical advancement in materials technology for modern gas turbine engines. TBCs are widely used in gas turbine engines for both power-generation and propulsion applications. Metallic oxidation-resistant coatings (ORCs) are also widely employed as a stand-alone protective coating or bond coat for TBCs in many high-temperature applications. Among the widely studied durability issues in these high-temperature protective coatings, one critical challenge that received greater attention in recent years is their resistance to high-temperature degradation due to corrosive deposits arising from fuel impurities and CMAS (calcium-magnesium-alumino-silicate) sand deposits from air ingestion. The presence of vanadium, sulfur, phosphorus, sodium and calcium impurities in alternative fuels warrants a clear understanding of high-temperature materials degradation for the development of fuel-flexible gas turbine engines. Degradation due to CMAS is a critical problem for gas turbine components operating in a dust-laden environment. In this study, high-temperature degradation due to aggressive deposits such as V2O5, P2O 5, Na2SO4, NaVO3, CaSO4 and a laboratory-synthesized CMAS sand for free-standing air plasma sprayed (APS) yttria stabilized zirconia (YSZ), the topcoat of the TBC system, and APS CoNiCrAlY, the bond coat of the TBC system or a stand-alone ORC, is examined. Phase transformations and microstructural development were examined by using x-ray diffraction, scanning electron microscopy, and transmission electron microscopy. This study demonstrated that the V2O5 melt degrades the APS YSZ through the formation of ZrV2O7 and YVO 4 at temperatures below 747°C and above 747°C, respectively. Formation of YVO4 leads to the depletion of the Y2O 3 stabilizer and the deleterious transformation of the YSZ to the monoclinic ZrO2 phase. The investigation on the YSZ degradation by Na 2SO4 and a Na2SO4 + V2O 5 mixture (50-50 mol. %) demonstrated that Na2SO4 itself did not degrade the YSZ, however, in the presence of V2O 5, Na2SO4 formed vanadates such as NaVO3 that degraded the YSZ through YVO4 formation at temperature as low as 700°C. The APS YSZ was found to react with the P2O 5 melt by forming ZrP2O7 at all temperatures. This interaction led to the depletion of ZrO2 in the YSZ (i.e., enrichment of Y2O3 in t'-YSZ) and promoted the formation of the fluorite-cubic ZrO2 phase. Above 1250°C, CMAS deposits were observed to readily infiltrate and significantly dissolve the YSZ coating via thermochemical interactions. Upon cooling, zirconia reprecipitated with a spherical morphology and a composition that depended on the local melt chemistry. The molten CMAS attack destabilized the YSZ through the detrimental phase transformation (t' → t → f + m). Free standing APS CoNiCrAlY was also prone to degradation by corrosive molten deposits. The V2O5 melt degraded the APS CoNiCrAlY through various reactions involving acidic dissolution of the protective oxide scale, which yielded substitutional-solid solution vanadates such as (Co,Ni) 3(VO4)2 and (Cr,Al)VO4. The molten P2O5, on the other hand, was found to consume the bond coat constituents significantly via reactions that formed both Ni/Co rich phosphates and Cr/Al rich phosphates. Sulfate deposits such as Na2SO 4, when tested in encapsulation, damaged the CoNiCrAlY by Type I acidic fluxing hot corrosion mechanisms at 1000°C that resulted in accelerated oxidation and sulfidation. The formation of a protective continuous Al 2O3 oxide scale by preoxidation treatment significantly delayed the hot corrosion of CoNiCrAlY by sulfates. However, CoNiCrAlY in both as-sprayed and preoxidized condition suffered a significant damage by CaSO4 deposits via a basic fluxing mechanism that yielded CaCrO4 and CaAl2O4. The CMAS melt also dissolved the protective Al2O3 oxide scale developed on CoNiCrAlY by forming anorthite platelets and spinel oxides. Based on the detailed investigation on degradation of the APS YSZ and CoNiCrAlY by various corrosive deposits, an experimental attempt was carried out to mitigate the melt-induced deposit attack. Experimental results from this study demonstrate, for the first time, that an oxide overlay produced by electrophoretic deposition (EPD) can effectively perform as an environmental barrier overlay for APS TBCs. The EPD protective overlay has a uniform and easily-controllable thickness, uniformly distributed closed pores and tailored chemistry. The EPD Al2O3 and MgO overlays were successful in protecting the APS YSZ TBCs against CMAS attack and hot corrosion attack (e.g., sulfate and vanadate), respectively. Furnace thermal cyclic oxidation testing of overlay-modified TBCs on bond-coated superalloy also demonstrated the good adhesive durability of the EPD Al2O3 overlay.