Modeling and Optimization for Morphing Wing Concept Generation II. Part 1; Morphing Wing Modeling and Structural Sizing Techniques

NASA Technical Reports Server (NTRS)

Skillen, Michael D.; Crossley, William A.

2008-01-01

This report documents a series of investigations to develop an approach for structural sizing of various morphing wing concepts. For the purposes of this report, a morphing wing is one whose planform can make significant shape changes in flight - increasing wing area by 50% or more from the lowest possible area, changing sweep 30 or more, and / or increasing aspect ratio by as much as 200% from the lowest possible value. These significant changes in geometry mean that the underlying load-bearing structure changes geometry. While most finite element analysis packages provide some sort of structural optimization capability, these codes are not amenable to making significant changes in the stiffness matrix to reflect the large morphing wing planform changes. The investigations presented here use a finite element code capable of aeroelastic analysis in three different optimization approaches -a "simultaneous analysis" approach, a "sequential" approach, and an "aggregate" approach.

Schinus terebinthifolius countercurrent chromatography (Part III): Method transfer from small countercurrent chromatography column to preparative centrifugal partition chromatography ones as a part of method development.

PubMed

das Neves Costa, Fernanda; Hubert, Jane; Borie, Nicolas; Kotland, Alexis; Hewitson, Peter; Ignatova, Svetlana; Renault, Jean-Hugues

2017-03-03

Countercurrent chromatography (CCC) and centrifugal partition chromatography (CPC) are support free liquid-liquid chromatography techniques sharing the same basic principles and features. Method transfer has previously been demonstrated for both techniques but never from one to another. This study aimed to show such a feasibility using fractionation of Schinus terebinthifolius berries dichloromethane extract as a case study. Heptane - ethyl acetate - methanol -water (6:1:6:1, v/v/v/v) was used as solvent system with masticadienonic and 3β-masticadienolic acids as target compounds. The optimized separation methodology previously described in Part I and II, was scaled up from an analytical hydrodynamic CCC column (17.4mL) to preparative hydrostatic CPC instruments (250mL and 303mL) as a part of method development. Flow-rate and sample loading were further optimized on CPC. Mobile phase linear velocity is suggested as a transfer invariant parameter if the CPC column contains sufficient number of partition cells. Copyright © 2017 Elsevier B.V. All rights reserved.

A finite element model of a six-year-old child for simulating pedestrian accidents.

PubMed

Meng, Yunzhu; Pak, Wansoo; Guleyupoglu, Berkan; Koya, Bharath; Gayzik, F Scott; Untaroiu, Costin D

2017-01-01

Child pedestrian protection deserves more attention in vehicle safety design since they are the most vulnerable road users who face the highest mortality rate. Pediatric Finite Element (FE) models could be used to simulate and understand the pedestrian injury mechanisms during crashes in order to mitigate them. Thus, the objective of the study was to develop a computationally efficient (simplified) six-year-old (6YO-PS) pedestrian FE model and validate it based on the latest published pediatric data. The 6YO-PS FE model was developed by morphing the existing GHBMC adult pedestrian model. Retrospective scan data were used to locally adjust the geometry as needed for accuracy. Component test simulations focused only the lower extremities and pelvis, which are the first body regions impacted during pedestrian accidents. Three-point bending test simulations were performed on the femur and tibia with adult material properties and then updated using child material properties. Pelvis impact and knee bending tests were also simulated. Finally, a series of pediatric Car-to-Pedestrian Collision (CPC) were simulated with pre-impact velocities ranging from 20km/h up to 60km/h. The bone models assigned pediatric material properties showed lower stiffness and a good match in terms of fracture force to the test data (less than 6% error). The pelvis impact force predicted by the child model showed a similar trend with test data. The whole pedestrian model was stable during CPC simulations and predicted common pedestrian injuries. Overall, the 6YO-PS FE model developed in this study showed good biofidelity at component level (lower extremity and pelvis) and stability in CPC simulations. While more validations would improve it, the current model could be used to investigate the lower limb injury mechanisms and in the prediction of the impact parameters as specified in regulatory testing protocols. Copyright © 2016 Elsevier Ltd. All rights reserved.

Variable stiffness corrugated composite structure with shape memory polymer for morphing skin applications

NASA Astrophysics Data System (ADS)

Gong, Xiaobo; Liu, Liwu; Scarpa, Fabrizio; Leng, Jinsong; Liu, Yanju

2017-03-01

This work presents a variable stiffness corrugated structure based on a shape memory polymer (SMP) composite with corrugated laminates as reinforcement that shows smooth aerodynamic surface, extreme mechanical anisotropy and variable stiffness for potential morphing skin applications. The smart composite corrugated structure shows a low in-plane stiffness to minimize the actuation energy, but also possess high out-of-plane stiffness to transfer the aerodynamic pressure load. The skin provides an external smooth aerodynamic surface because of the one-sided filling with the SMP. Due to variable stiffness of the shape memory polymer the morphing skin exhibits a variable stiffness with a change of temperature, which can help the skin adjust its stiffness according different service environments and also lock the temporary shape without external force. Analytical models related to the transverse and bending stiffness are derived and validated using finite element techniques. The stiffness of the morphing skin is further investigated by performing a parametric analysis against the geometry of the corrugation and various sets of SMP fillers. The theoretical and numerical models show a good agreement and demonstrate the potential of this morphing skin concept for morphing aircraft applications. We also perform a feasibility study of the use of this morphing skin in a variable camber morphing wing baseline. The results show that the morphing skin concept exhibits sufficient bending stiffness to withstand the aerodynamic load at low speed (less than 0.3 Ma), while demonstrating a large transverse stiffness variation (up to 191 times) that helps to create a maximum mechanical efficiency of the structure under varying external conditions.

The Other-Race Effect in Infancy: Evidence Using a Morphing Technique

ERIC Educational Resources Information Center

Hayden, Angela; Bhatt, Ramesh S.; Joseph, Jane E.; Tanaka, James W.

2007-01-01

Human adults are more accurate at discriminating faces from their own race than faces from another race. This "other-race effect" (ORE) has been characterized as a reflection of face processing specialization arising from differential experience with own-race faces. We examined whether 3.5-month-old infants exhibit ORE using morphed faces on which…

Assessing Hydrological and Energy Budgets in Amazonia through Regional Downscaling, and Comparisons with Global Reanalysis Products

NASA Astrophysics Data System (ADS)

Nunes, A.; Ivanov, V. Y.

2014-12-01

Although current global reanalyses provide reasonably accurate large-scale features of the atmosphere, systematic errors are still found in the hydrological and energy budgets of such products. In the tropics, precipitation is particularly challenging to model, which is also adversely affected by the scarcity of hydrometeorological datasets in the region. With the goal of producing downscaled analyses that are appropriate for a climate assessment at regional scales, a regional spectral model has used a combination of precipitation assimilation with scale-selective bias correction. The latter is similar to the spectral nudging technique, which prevents the departure of the regional model's internal states from the large-scale forcing. The target area in this study is the Amazon region, where large errors are detected in reanalysis precipitation. To generate the downscaled analysis, the regional climate model used NCEP/DOE R2 global reanalysis as the initial and lateral boundary conditions, and assimilated NOAA's Climate Prediction Center (CPC) MORPHed precipitation (CMORPH), available at 0.25-degree resolution, every 3 hours. The regional model's precipitation was successfully brought closer to the observations, in comparison to the NCEP global reanalysis products, as a result of the impact of a precipitation assimilation scheme on cumulus-convection parameterization, and improved boundary forcing achieved through a new version of scale-selective bias correction. Water and energy budget terms were also evaluated against global reanalyses and other datasets.

Silver-Doped Calcium Phosphate Bone Cements with Antibacterial Properties

PubMed Central

Rau, J. V.; Fosca, M.; Graziani, V.; Egorov, A. A.; Zobkov, Yu. V.; Fedotov, A. Yu.; Ortenzi, M.; Caminiti, R.; Baranchikov, A. E.; Komlev, V. S.

2016-01-01

Calcium phosphate bone cements (CPCs) with antibacterial properties are demanded for clinical applications. In this study, we demonstrated the use of a relatively simple processing route based on preparation of silver-doped CPCs (CPCs-Ag) through the preparation of solid dispersed active powder phase. Real-time monitoring of structural transformations and kinetics of several CPCs-Ag formulations (Ag = 0 wt %, 0.6 wt % and 1.0 wt %) was performed by the Energy Dispersive X-ray Diffraction technique. The partial conversion of β-tricalcium phosphate (TCP) phase into the dicalcium phosphate dihydrate (DCPD) took place in all the investigated cement systems. In the pristine cement powders, Ag in its metallic form was found, whereas for CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, CaAg(PO3)3 was detected and Ag (met.) was no longer present. The CPC-Ag 0 wt % cement exhibited a compressive strength of 6.5 ± 1.0 MPa, whereas for the doped cements (CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt %) the reduced values of the compressive strength 4.0 ± 1.0 and 1.5 ± 1.0 MPa, respectively, were detected. Silver-ion release from CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, measured by the Atomic Emission Spectroscopy, corresponds to the average values of 25 µg/L and 43 µg/L, respectively, rising a plateau after 15 days. The results of the antibacterial test proved the inhibitory effect towards pathogenic Escherichia coli for both CPC-Ag 0.6 wt % and CPC-Ag 1.0 wt % cements, better performances being observed for the cement with a higher Ag-content. PMID:27096874

Wing shape variation associated with mimicry in butterflies.

PubMed

Jones, Robert T; Le Poul, Yann; Whibley, Annabel C; Mérot, Claire; ffrench-Constant, Richard H; Joron, Mathieu

2013-08-01

Mimetic resemblance in unpalatable butterflies has been studied by evolutionary biologists for over a century, but has largely focused on the convergence in wing color patterns. In Heliconius numata, discrete color-pattern morphs closely resemble comimics in the distantly related genus Melinaea. We examine the possibility that the shape of the butterfly wing also shows adaptive convergence. First, simple measures of forewing dimensions were taken of individuals in a cross between H. numata morphs, and showed quantitative differences between two of the segregating morphs, f. elegans and f. silvana. Second, landmark-based geometric morphometric and elliptical Fourier outline analyses were used to more fully characterize these shape differences. Extension of these techniques to specimens from natural populations suggested that, although many of the coexisting morphs could not be discriminated by shape, the differences we identified between f. elegans and f. silvana hold in the wild. Interestingly, despite extensive overlap, the shape variation between these two morphs is paralleled in their respective Melinaea comimics. Our study therefore suggests that wing-shape variation is associated with mimetic resemblance, and raises the intriguing possibility that the supergene responsible for controlling the major switch in color pattern between morphs also contributes to wing shape differences in H. numata. © 2013 The Author(s). Evolution © 2013 The Society for the Study of Evolution.

HRTEM low dose: the unfold of the morphed graphene, from amorphous carbon to morphed graphenes.

PubMed

Calderon, H A; Okonkwo, A; Estrada-Guel, I; Hadjiev, V G; Alvarez-Ramírez, F; Robles Hernández, F C

We present experimental evidence under low-dose conditions transmission electron microscopy for the unfolding of the evolving changes in carbon soot during mechanical milling. The milled soot shows evolving changes as a function of the milling severity or time. Those changes are responsible for the transformation from amorphous carbon to graphenes, graphitic carbon, and highly ordered structures such as morphed graphenes, namely Rh6 and Rh6-II. The morphed graphenes are corrugated layers of carbon with cross-linked covalently nature and sp 2 - or sp 3 -type allotropes. Electron microscopy and numerical simulations are excellent complementary tools to identify those phases. Furthermore, the TEAM 05 microscope is an outstanding tool to resolve the microstructure and prevent any damage to the sample. Other characterization techniques such as XRD, Raman, and XPS fade to convey a true identification of those phases because the samples are usually blends or mixes of the mentioned phases.

On-line hyphenation of centrifugal partition chromatography and high pressure liquid chromatography for the fractionation of flavonoids from Hippophaë rhamnoides L. berries.

PubMed

Michel, Thomas; Destandau, Emilie; Elfakir, Claire

2011-09-09

Centrifugal Partition Chromatography (CPC), a liquid-liquid preparative chromatography using two immiscible solvent systems, benefits from numerous advantages for the separation or purification of synthetic or natural products. This study presents the on-line hyphenation of CPC-Evaporative Light Scattering Detector (CPC-ELSD) with High Performance Liquid Chromatography-UV (HPLC-UV) for the fractionation of flavonols from a solvent-free microwave extract of sea buckthorn (Hippophaë rhamnoides L., Elaeagnaceae) berries. An Arizona G system was used for the fractionation of flavonoids by CPC and a fused core Halo C18 column allowed the on-line analyses of collected fractions by HPLC. The on-line CPC/HPLC procedure allowed the simultaneous fractionation step at preparative scale combined with the HPLC analyses which provide direct fingerprint of collected fractions. Thus the crude extract was simplified and immediate information on the composition of fractions could be obtained. Furthermore, this methodology reduced the time of post-fractionation steps and facilitated identification of main molecules by Mass Spectrometry (MS). Rutin, isorhamnetin-3-O-rutinoside, isorhamnetin-3-O-glucoside, quercetin-3-O-glucoside, isorhamnetin-rhamnoside, quercetin and isorhamnetin were identified. CPC-ELSD/HPLC-UV could be considered as a high-throughput technique for the guided fractionation of bioactive natural products from complex crude extracts. Copyright © 2011 Elsevier B.V. All rights reserved.

Planform, aero-structural, and flight control optimization for tailless morphing aircraft

NASA Astrophysics Data System (ADS)

Molinari, Giulio; Arrieta, Andres F.; Ermanni, Paolo

2015-04-01

Tailless airplanes with swept wings rely on variations of the spanwise lift distribution to provide controllability in roll, pitch and yaw. Conventionally, this is achieved utilizing multiple control surfaces, such as elevons, on the wing trailing edge. As every flight condition requires different control moments (e.g. to provide pitching moment equilibrium), these surfaces are practically permanently displaced. Due to their nature, causing discontinuities, corners and gaps, they bear aerodynamic penalties, mostly in terms of shape drag. Shape adaptation, by means of chordwise morphing, has the potential of varying the lift of a wing section by deforming its profile in a way that minimizes the resulting drag. Furthermore, as the shape can be varied differently along the wingspan, the lift distribution can be tailored to each specific flight condition. For this reason, tailless aircraft appear as a prime choice to apply morphing techniques, as the attainable benefits are potentially significant. In this work, we present a methodology to determine the optimal planform, profile shape, and morphing structure for a tailless aircraft. The employed morphing concept is based on a distributed compliance structure, actuated by Macro Fiber Composite (MFC) piezoelectric elements. The multidisciplinary optimization is performed considering the static and dynamic aeroelastic behavior of the resulting structure. The goal is the maximization of the aerodynamic efficiency while guaranteeing the controllability of the plane, by means of morphing, in a set of flight conditions.

The nonlinear aeroelastic characteristics of a folding wing with cubic stiffness

NASA Astrophysics Data System (ADS)

Hu, Wei; Yang, Zhichun; Gu, Yingsong; Wang, Xiaochen

2017-07-01

This paper focuses on the nonlinear aeroelastic characteristics of a folding wing in the quasi-steady condition (namely at fixed folding angles) and during the morphing process. The structure model of the folding wing is formulated by the Lagrange equations, and the constraint equation is used to describe the morphing strategy. The aerodynamic influence coefficient matrices at several folding angles are calculated by the Doublet Lattice method, and described as rational functions in the Laplace domain by the rational function approximation, and then the Kriging agent model technique is adopted to interpolate the coefficient matrices of the rational functions, and the aerodynamics model of the folding wing during the morphing process is built. The aeroelastic responses of the folding wing with cubic stiffness are simulated, and the results show that the motion types of aeroelastic responses in the quasi-steady condition and during the morphing process are all sensitive to the initial condition and folding angle. During the morphing process, the transition of the motion types is observed. And apart from the period of transition, the aeroelastic response at some folding angles may exhibit different motion types, which can be found from the results in the quasi-steady condition.

Preliminary Aerodynamic Investigation of Fan Rotor Blade Morphing

NASA Technical Reports Server (NTRS)

Tweedt, Daniel L.

2012-01-01

Various new technologies currently under development may enable controlled blade shape variability, or so-called blade morphing, to be practically employed in aircraft engine fans and compressors in the foreseeable future. The current study is a relatively brief, preliminary computational fluid dynamics investigation aimed at partially demonstrating and quantifying the aerodynamic potential of fan rotor blade morphing. The investigation is intended to provide information useful for near-term planning, as well as aerodynamic solution data sets that can be subsequently analyzed using advanced acoustic diagnostic tools, for the purpose of making fan noise comparisons. Two existing fan system models serve as baselines for the investigation: the Advanced Ducted Propulsor fan with a design tip speed of 806 ft/sec and a pressure ratio of 1.294, and the Source Diagnostic Test fan with a design tip speed of 1215 ft/sec and a pressure ratio of 1.470. Both are 22-in. sub-scale, low-noise research fan/nacelle models that have undergone extensive experimental testing in the 9- by 15-foot Low Speed Wind Tunnel at the NASA Glenn Research Center. The study, restricted to fan rotor blade morphing only, involves a fairly simple blade morphing technique. Specifically, spanwise-linear variations in rotor blade-section setting angle are applied to alter the blade shape; that is, the blade is linearly retwisted from hub to tip. Aerodynamic performance comparisons are made between morphed-blade and corresponding baseline configurations on the basis of equal fan system thrust, where rotor rotational speed for the morphed-blade fan is varied to change the thrust level for that configuration. The results of the investigation confirm that rotor blade morphing could be a useful technology, with the potential to enable significant improvements in fan aerodynamic performance. Even though the study is very limited in scope and confined to simple geometric perturbations of two existing fan systems, the aerodynamic effectiveness of blade morphing is demonstrated by the configurations analyzed. In particular, for the Advanced Ducted Propulsor fan it is demonstrated that the performance levels of the original variable-pitch baseline design can be achieved using blade morphing instead of variable pitch, and for the Source Diagnostic Test fan the performance at important off-design operating points is substantially increased with blade morphing.

Assessment of Satellite Precipitation Products in the Philippine Archipelago

NASA Astrophysics Data System (ADS)

Ramos, M. D.; Tendencia, E.; Espana, K.; Sabido, J.; Bagtasa, G.

2016-06-01

Precipitation is the most important weather parameter in the Philippines. Made up of more than 7100 islands, the Philippine archipelago is an agricultural country that depends on rain-fed crops. Located in the western rim of the North West Pacific Ocean, this tropical island country is very vulnerable to tropical cyclones that lead to severe flooding events. Recently, satellite-based precipitation estimates have improved significantly and can serve as alternatives to ground-based observations. These data can be used to fill data gaps not only for climatic studies, but can also be utilized for disaster risk reduction and management activities. This study characterized the statistical errors of daily precipitation from four satellite-based rainfall products from (1) the Tropical Rainfall Measuring Mission (TRMM), (2) the CPC Morphing technique (CMORPH) of NOAA and (3) the Global Satellite Mapping of Precipitation (GSMAP) and (4) Precipitation Estimation from Remotely Sensed information using Artificial Neural Networks (PERSIANN). Precipitation data were compared to 52 synoptic weather stations located all over the Philippines. Results show GSMAP to have over all lower bias and CMORPH with lowest Mean Absolute Error (MAE) and Root Mean Square Error (RMSE). In addition, a dichotomous rainfall test reveals GSMAP and CMORPH have low Proportion Correct (PC) for convective and stratiform rainclouds, respectively. TRMM consistently showed high PC for almost all raincloud types. Moreover, all four satellite precipitation showed high Correct Negatives (CN) values for the north-western part of the country during the North-East monsoon and spring monsoonal transition periods.

Multidisciplinary Techniques and Novel Aircraft Control Systems

NASA Technical Reports Server (NTRS)

Padula, Sharon L.; Rogers, James L.; Raney, David L.

2000-01-01

The Aircraft Morphing Program at NASA Langley Research Center explores opportunities to improve airframe designs with smart technologies. Two elements of this basic research program are multidisciplinary design optimization (MDO) and advanced flow control. This paper describes examples where MDO techniques such as sensitivity analysis, automatic differentiation, and genetic algorithms contribute to the design of novel control systems. In the test case, the design and use of distributed shape-change devices to provide low-rate maneuvering capability for a tailless aircraft is considered. The ability of MDO to add value to control system development is illustrated using results from several years of research funded by the Aircraft Morphing Program.

Multidisciplinary Techniques and Novel Aircraft Control Systems

NASA Technical Reports Server (NTRS)

Padula, Sharon L.; Rogers, James L.; Raney, David L.

2000-01-01

The Aircraft Morphing Program at NASA Langley Research Center explores opportunities to improve airframe designs with smart technologies. Two elements of this basic research program are multidisciplinary design optimization (MDO) and advanced flow control. This paper describes examples where MDO techniques such as sensitivity analysis, automatic differentiation, and genetic algorithms contribute to the design of novel control systems. In the test case, the design and use of distributed shapechange devices to provide low-rate maneuvering capability for a tailless aircraft is considered. The ability of MDO to add value to control system development is illustrated using results from several years of research funded by the Aircraft Morphing Program.

An Image Morphing Technique Based on Optimal Mass Preserving Mapping

DTIC Science & Technology

2007-06-01

Yan Yang, Steven Haker , and Allen Tannenbaum Abstract—Image morphing, or image interpolation in the time domain, deals with the metamorphosis of one...of Technology, Atlanta, GA 30332 USA (e-mail: zlzl@ece.gatech.edu; zhulei1976@hotmail.com; yan.yang@gatech.edu; tannenba@ece.gatech.edu). S. Haker is...with the Surgical Planning Laboratory, Brigham and Women’s Hospital and Harvard Medical School, Boston, MA 02115 USA (e-mail: haker @bwh.harvard.edu

Monitoring the bending and twist of morphing structures

NASA Astrophysics Data System (ADS)

Smoker, J.; Baz, A.

2008-03-01

This paper presents the development of the theoretical basis for the design of sensor networks for determining the 2-dimensioal shape of morphing structures by monitoring simultaneously the bending and twist deflections. The proposed development is based on the non-linear theory of finite elements to extract the transverse linear and angular deflections of a plate-like structure. The sensors outputs are wirelessly transmitted to the command unit to simultaneously compute maps of the linear and angular deflections and maps of the strain distribution of the entire structure. The deflection and shape information are required to ascertain that the structure is properly deployed and that its surfaces are operating wrinkle-free. The strain map ensures that the structure is not loaded excessively to adversely affect its service life. The developed theoretical model is validated experimentally using a prototype of a variable cambered span morphing structure provided with a network of distributed sensors. The structure/sensor network system is tested under various static conditions to determine the response characteristics of the proposed sensor network as compared to other conventional sensor systems. The presented theoretical and experimental techniques can have a great impact on the safe deployment and effective operation of a wide variety of morphing and inflatable structures such as morphing aircraft, solar sails, inflatable wings, and large antennas.

The measurement of ultrafine particles: A pilot study using a portable particle counting technique to measure generated particles during a micromachining process

NASA Astrophysics Data System (ADS)

Handy, Rodney G.; Jackson, Mark J.; Robinson, Grant M.; Lafreniere, Michael D.

2006-04-01

The accurate measurement of airborne particles in the nanometer range is a challenging task. Because several studies have linked exposures to airborne ultrafine particles to elevated human health risks, the need to assess the concentrations of particles in the workplace that are below 100 nm in diameter is imperative. Several different techniques for monitoring nanoparticles are now available, and others are currently being tested for their merit. Laboratory condensation particle counters (CPC), field-portable CPC, nanometer differential mobility analyzers, electron microscopy, and other novel and experimental approaches to measuring nanoparticles have been recently used in investigations. The first part of this article gives an overview of these techniques, and provides the advantages and disadvantages for each. The second part of this article introduces a portable technique, coupling two particle measurement devices that are capable of characterizing microscale and nanoscale particles in the field environment. Specifically, this pilot study involved the use of a direct-reading CPC and a laser particle counter to measure airborne concentrations of ultrafine particles during a laboratory machining process. The measurements were evaluated in real time, and subsequently, decisions regarding human exposure could be made in an efficient and effective manner. Along with the results from this study, further research efforts in related areas are discussed.

Cystostomie percutanée à la pince de Kelly: indications, technique et résultats

PubMed Central

Diabaté, Ibrahima; Ouédraogo, Bouréima; Sow, Ibrahima; Bâ, Aliou

2015-01-01

Introduction La dérivation urinaire sus-pubienne est pratiquée dans différentes circonstances. Cette étude vise à décrire la technique de cystostomie percutanée (CPC) pratiquée à l'aide d'une pince de Kelly pour la pose d'une sonde de Foley, à définir les indications de cette technique et à rapporter les résultats. Méthodes Du 1er janvier 2005 au 31 décembre 2014, il a été réalisé 194 CPC à la pince de Kelly dans notre service, en urgence, sous anesthésie locale, chez des patients en rétention vésicale. Cette technique, dérivée de la cystostomie par ponction au trocart vise à placer dans la vessie une sonde de Foley après incision cutanée et aponévrotique (de 1 cm sur la ligne médiane, à 1,5 - 2 cm au-dessus de la symphyse pubienne) et la ponction vésicale à la pince de Kelly à travers cette incision. Résultats Les 194 patients étaient tous de sexe masculin, âgés en moyenne de 50 ans ± 21 (extrêmes de 17 ans et 86 ans). Les pathologies à l'origine des rétentions vésicales étaient: les rétrécissements urétraux (n=119), les hypertrophies bénignes de la prostate (n=47), les cancers de prostate (n=21), les traumatismes de l'urètre (n=7). Tous les patients ont été opérés avec succès par cette méthode et les suites ont été simples. Le temps de réalisation était de 6 minutes ± 1. Les sondes de Foley mises en place étaient de charrière 16 (n=59), charrière 18 (n=116) et charrière 20 (n=19). La cicatrisation du trajet de la CPC après l'ablation de la sonde de Foley n'a posée aucun problème chez 146 patients suivis, les 48 autres ayant été perdus de vue. Conclusion La CPC à la pince de Kelly est une technique simple, rapide et pas onéreuse. Ses indications sont les mêmes que pour toute CPC et elle représente une alternative à la cystostomie par chirurgie ouverte. PMID:26893798

Mandibular angle augmentation with the use of distraction and homologous lyophilized cartilage in a case of morphing to Michael Jackson surgery.

PubMed

Mommaerts, M Y; Abeloos, J S; Gropp, H

2001-08-01

Correction of an ill-defined mandibular angle is not an easy task, whether it is requested by the "congenital, orthognathic or cosmetic" patient. Deliberate over-correction has not been reported to our knowledge. This article presents a combination of distraction osteogenesis and lyophilized cartilage used to three-dimensionally over-augment the mandibular angle of a long-face prognathic patient who had the wish to be morphed to Michael Jackson or at least as far as current technique and his endogenic features allowed.

Preparation of Calcium Phosphate Cement and Polymethyl Methacrylate for Biological Composite Bone Cements

PubMed Central

Yang, Jun; Zhang, Kairui; Zhang, Sheng; Fan, Jiping; Guo, Xinhui; Dong, Weiqiang; Wang, Shengnan; Chen, Yirong; Yu, Bin

2015-01-01

Background We studied the biological safety, biomechanics, and tissue compatibility of calcium phosphate cement and Polymethyl Methacrylate composite bone cement mixed in different ratios. Material/Methods CPC and PMMA were mixed in different ratios (3: 1, 2: 1, 1: 1, 1: 2, 1: 5, 1: 10, 1: 15, and 1: 20). PMMA solvent is a general solvent containing a dissolved preparation of the composite bone cement specific to a given specimen to determine biological safety, biomechanics, and tissue compatibility. Results The CPC/PMMA (33%) group, CPC/PMMA (50%) group, CPC/PMMA (67%) group, and CPC/PMMA (75%) group were more in line with the composite bone cement without cytotoxicity requirements. The compressive strength of the CPC/PMMA (67%) group and CPC/PMMA (75%) group was 20Mpa–30Mpa, while that of the CPC/PMMA (4.8%) group, CPC/PMMA (6.25%) group, CPC/PMMA (9.1%) group, CPC/PMMA (16.7%) group, CPC/PMMA (33%) group, and CPC/PMMA (50%) group was 40Mpa–70Mpa. Curing time was longer in the CPC group (more than 11 min) and shorter in the PMMA group (less than 2 min). The results of weight loss rate showed that there were no significant differences between the CPC/PMMA group (4.8%, 6.25%, 9.1%, 16.7%, 33%) and PMMA control group (p>0.05). With the decrease of CPC content, the rate of weight loss gradually decreased. Conclusions The CPC/PMMA (50%) group, CPC/PMMA (67%) group, and CPC/PMMA (75%) group provide greater variability and selectivity for the composite bone cement in obtaining better application. PMID:25904398

Life history differences between fat and lean morphs of lake charr (Salvelinus namaycush) in Great Slave Lake, Northwest Territories, Canada

USGS Publications Warehouse

Hansen, Michael J.; Nate, Nancy A.; Chavarie, Louise; Muir, Andrew M.; Zimmerman, Mara S.; Krueger, Charles C.

2016-01-01

Life history characteristics (size, age, plumpness, buoyancy, survival, growth, and maturity) were compared between fat and lean morphs of lake charr Salvelinus namaycush in Great Slave Lake, Canada, to determine if differences may reflect effects of resource polymorphism. Lake charr were sampled using graded-mesh gill nets set in three depth strata. Of 236 lake charr captured, 122 were a fat morph and 114 were a lean morph. Males and females did not differ from each other in any attributes for either fat or lean morphs. The fat morph averaged 15 mm longer, 481 g heavier, and 4.7 years older than the lean morph. The fat morph averaged 26% heavier and 48% more buoyant at length than the lean morph. Survival of the fat morph was 1.7% higher than that of the lean morph. The fat morph grew at a slower annual rate to a shorter asymptotic length than the lean morph. Fat and lean morphs matured at similar lengths and ages. We concluded that the connection between resource polymorphism and life histories in lean versus fat lake charr suggests that morph-specific restoration objectives may be needed in lakes where lake charr diversity is considered to be a restoration goal.

The effect of ion-exchange purification on the determination of plutonium at the New Brunswick Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, W.G.; Spaletto, M.I.; Lewis, K.

The method of plutonium (Pu) determination at the Brunswick Laboratory (NBL) consists of a combination of ion-exchange purification followed by controlled-potential coulometric analysis (IE/CPC). The present report's purpose is to quantify any detectable Pu loss occurring in the ion-exchange (IE) purification step which would cause a negative bias in the NBL method for Pu analysis. The magnitude of any such loss would be contained within the reproducibility (0.05%) of the IE/CPC method which utilizes a state-of-the-art autocoulometer developed at NBL. When the NBL IE/CPC method is used for Pu analysis, any loss in ion-exchange purification (<0.05%) is confounded with themore » repeatability of the ion-exchange and the precision of the CPC analysis technique (<0.05%). Consequently, to detect a bias in the IE/CPC method due to the IE alone using the IE/CPC method itself requires that many randomized analyses on a single material be performed over time and that statistical analysis of the data be performed. The initial approach described in this report to quantify any IE loss was an independent method, Isotope Dilution Mass Spectrometry; however, the number of analyses performed was insufficient to assign a statistically significant value to the IE loss (<0.02% of 10 mg samples of Pu). The second method used for quantifying any IE loss of Pu was multiple ion exchanges of the same Pu aliquant; the small number of analyses possible per individual IE together with the column-to-column variability over multiple ion exchanges prevented statistical detection of any loss of <0.05%. 12 refs.« less

Development of "ultrasound-assisted dynamic extraction" and its combination with CCC and CPC for simultaneous extraction and isolation of phytochemicals.

PubMed

Zhang, Yuchi; Liu, Chunming; Li, Jing; Qi, Yanjuan; Li, Yuchun; Li, Sainan

2015-09-01

A new method for the extraction of medicinal herbs termed ultrasonic-assisted dynamic extraction (UADE) was designed and evaluated. This technique was coupled with counter-current chromatography (CCC) and centrifugal partition chromatography (CPC) and then applied to the continuous extraction and online isolation of chemical constituents from Paeonia lactiflora Pall (white peony) roots. The mechanical parameters, including the pitch and diameter of the shaft, were optimized by means of mathematical modeling. Furthermore, the configuration and mechanism of online UADE coupled with CCC and CPC were elaborated. The stationary phases of the two-phase solvent systems from CCC and CPC were utilized as the UADE solution. The extraction solution was pumped into the sample loop and then introduced into the CCC column; the target compounds were eluted with the lower aqueous phase of the two-phase solvent system. During the CCC separation, the extraction solution was continuously fed in the sample loop by turning the ten-port valve; the extraction solution was then pumped into the CPC column and eluted by the mobile phase of the two-phase solvent system mentioned above. When the first cycle of the UADE/CCC/CPC was completed, the second cycle experiment could be carried out, and so on. Four target compounds (albiflorin, benzoylpaeoniflorin, paeoniflorin, and galloylpaeoniflorin) with purities above 94.96% were successfully extracted and isolated online using the two-phase solvent system comprising ethyl acetate-n-butanol-ethanol-water (1:3.5:2:4.5, v/v/v/v). Compared with conventional extraction methods, the instrumental setup of the present method offers the advantages of automation and systematic extraction and isolation of natural products. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Calcium phosphate cement with biofunctional agents and stem cell seeding for dental and craniofacial bone repair.

PubMed

Thein-Han, WahWah; Liu, Jun; Xu, Hockin H K

2012-10-01

Calcium phosphate cement (CPC) can be injected to harden in situ and is promising for dental and craniofacial applications. However, human stem cell attachment to CPC is relatively poor. The objectives of this study were to incorporate biofunctional agents into CPC, and to investigate human umbilical cord mesenchymal stem cell (hUCMSC) seeding on biofunctionalized CPC for osteogenic differentiation for the first time. Five types of biofunctional agents were used: RGD (Arg-Gly-Asp) peptides, human fibronectin (Fn), fibronectin-like engineered polymer protein (FEPP), extracellular matrix Geltrex, and human platelet concentrate. Five biofunctionalized CPC scaffolds were fabricated: CPC-RGD, CPC-Fn, CPC-FEPP, CPC-Geltrex, and CPC-Platelets. The hUCMSC attachment, proliferation, osteogenic differentiation and mineral synthesis were measured. The hUCMSCs on biofunctionalized CPCs had much better cell attachment, proliferation, actin fiber expression, osteogenic differentiation and mineral synthesis, compared to the traditional CPC control. Cell proliferation was increased by an order of magnitude via incorporation of biofunctional agents in CPC (p<0.05). Mineral synthesis on biofunctionalized CPCs was 3-5 folds of those of control (p<0.05). hUCMSCs differentiated with high alkaline phosphatase, Runx2, osteocalcin, and collagen I gene expressions. Mechanical properties of biofunctionalized CPC matched the reported strength and elastic modulus of cancellous bone. A new class of biofunctionalized CPCs was developed, including CPC-RGD, CPC-Fn, CPC-FEPP, CPC-Geltrex, and CPC-Platelets. hUCMSCs on biofunctionalized CPCs had cell density, cell proliferation, actin fiber density, and bone mineralization that were dramatically better than those on traditional CPC. Novel biofunctionalized CPC scaffolds with greatly enhanced human stem cell proliferation and differentiation are promising to facilitate bone regeneration in a wide range of dental, craniofacial and orthopedic applications. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

[A pharmacological study of chlorphenesin carbamate. Tolerance to chlorphenesin carbamate (author's transl)].

PubMed

Sasajima, M; Aihara, H; Akiyama, F; Tsuchida, K; Otomo, S

1977-04-01

Tolerance to chlorphenesin carbamate (CPC) was investigated from the viewpoints of action of CPC, serum free CPC concentration, the activity of UDP-glucuronyltransferase and the content of cytochrome P-450. CPC was administered once daily for 7 or 14 days. In mice, the hypnotic action of hexobarbital injected 24 hours after the last administration of CPC and the motor incoordinating action of CPC significantly decreased on the 7th day, but slightly recovered on the 14th day. Serum free CPC concentration also decreased on the 7th day, but recovered on the 14th day. A significant relationship between the motor incoordinating action of CPC and serum free CPC concentration was observed. Therefore, the recovery of CPC effect on the 14th day was considered to be due to the recovery from the induction of drug-metabolizing enzymes. On the other hand, in rats, the weekly alteration of the motor incoordinating action of CPC was similar to that observed in mice. Serum free CPC concentration on the 7th and 14th days was lower than that on the 1st day, and enzyme induction was observed during CPC administration. Notwithstanding the low level of serum free CPC concentration, the recovery of CPC effect was observed on the 14th day and such was considered to be due to habituation to the rotarod. In mice and rats, it was demonstrated that the intensity of CPC effect was dependent on serum free CPC concentration to the extent that enzyme induction played an important role in the development of tolerance. From these results, the tolerance to CPC is attributed to induction of drug-metabolizing enzymes in liver microsomes.

Interactive shape metamorphosis

NASA Technical Reports Server (NTRS)

Chen, David T.; State, Andrei; Banks, David

1994-01-01

A technique for controlled metamorphosis between surfaces in 3-space is described. Well-understood techniques to produce shape metamorphosis between models in a 2D parametric space is applied. The user selects morphable features interactively, and the morphing process executes in real time on a high-performance graphics multicomputer.

Quantitative Analysis of Endothelial Cell Loss in Preloaded Descemet Membrane Endothelial Keratoplasty Grafts.

PubMed

Wolle, Meraf A; DeMill, David L; Johnson, Lauren; Lentz, Stephen I; Woodward, Maria A; Mian, Shahzad I

2017-11-01

Availability of preloaded Descemet membrane endothelial keratoplasty (pDMEK) tissue may increase acceptance of DMEK in surgical management of endothelial disease. The goal of this study was to determine the safety of pDMEK grafts for 24 hours before surgery by analyzing endothelial cell loss (ECL) using 2 image analysis software programs. A total of 18 cadaveric corneas were prepared for DMEK using a standardized technique and loaded in a modified Jones tube injector. Nine of the corneas were injected into Calcein AM vital dye after 1 minute (controls), and the remaining 9 corneas were left preloaded for 24 hours before injection into vital dye for staining. The stained corneas were imaged using an inverted confocal microscope. ECL was then analyzed and quantified by 2 different graders using 2 image analysis software programs. The control DMEK tissue resulted in 22.0% ± 4.0% ECL compared with pDMEK tissue, which resulted in 19.2% ± 7.2% ECL (P = 0.31). Interobserver agreement was 0.93 for MetaMorph and 0.92 for Fiji. The average time required to process images with MetaMorph was 2 ± 1 minutes and with Fiji was 20 ± 10 minutes. Intraobserver agreement was 0.97 for MetaMorph and 0.93 for Fiji. Preloading DMEK tissue is safe and may provide an alternative technique for tissue distribution and surgery for DMEK. The use of MetaMorph software for quantifying ECL is a novel and accurate imaging method with increased efficiency and reproducibility compared with the previously validated Fiji.

Demographic stochasticity in small remnant populations of the declining distylous plant Primula veris

USGS Publications Warehouse

Kery, M.; Matthies, D.; Schmid, B.

2003-01-01

We studied ecological consequences of distyly for the declining perennial plant Primula veris in the Swiss Jura. Distyly favours cross-fertilization and avoids inbreeding, but may lead to pollen limitation and reduced reproduction if morph frequencies deviate from 50 %. Disassortative mating is promoted by the reciprocal position of stigmas and anthers in the two morphs (pin and thrum) and by intramorph incompatibility and should result in equal frequencies of morphs at equilibrium. However, deviations could arise because of demographic stochasticity, the lower intra-morph incompatibility of the pin morph, and niche differentiation between morphs. Demographic stochasticity should result in symmetric deviations from an even morph frequency among populations and in increased deviations with decreasing population size. If crosses between pins occurred, these would only generate pins, and this could result in a pin-bias of morph frequencies in general and in small populations in particular. If the morphs have different niches, morph frequencies should be related to environmental factors, morphs might be spatially segregated, and morphological differences between morphs would be expected. We tested these hypotheses in the declining distylous P. veris. We studied morph frequencies in relation to environmental conditions and population size, spatial segregation in field populations, morphological differences between morphs, and growth responses to nutrient addition. Morph frequencies in 76 populations with 1 - 80000 flowering plants fluctuated symmetrically about 50 %. Deviations from 50 % were much larger in small populations, and sixof the smallest populations had lost one morph altogether. In contrast, morph frequencies were neither related to population size nor to 17 measures of environmental conditions. We found no spatial segregation or morphological differences in the field or in the common garden. The results suggest that demographic stochasticity caused deviations of the morph ratiofrom unity in small populations. Demographic stochasticity was probably caused by the random elimination of plants during the fragmentation of formerly large continuous populations. Biased morph frequencies may be one of the reasons for the strongly reduced reproduction in small populations of P. veris.

Photocatalytic mineralization of commercial herbicides in a pilot-scale solar CPC reactor: photoreactor modeling and reaction kinetics constants independent of radiation field.

PubMed

Colina-Márquez, Jose; Machuca-Martínez, Fiderman; Li Puma, Gianluca

2009-12-01

The six-flux absorption-scattering model (SFM) of the radiation field in the photoreactor, combined with reaction kinetics and fluid-dynamic models, has proved to be suitable to describe the degradation of water pollutants in heterogeneous photocatalytic reactors, combining simplicity and accuracy. In this study, the above approach was extended to model the photocatalytic mineralization of a commercial herbicides mixture (2,4-D, diuron, and ametryne used in Colombian sugar cane crops) in a solar, pilot-scale, compound parabolic collector (CPC) photoreactor using a slurry suspension of TiO(2). The ray-tracing technique was used jointly with the SFM to determine the direction of both the direct and diffuse solar photon fluxes and the spatial profile of the local volumetric rate of photon absorption (LVRPA) in the CPC reactor. Herbicides mineralization kinetics with explicit photon absorption effects were utilized to remove the dependence of the observed rate constants from the reactor geometry and radiation field in the photoreactor. The results showed that the overall model fitted the experimental data of herbicides mineralization in the solar CPC reactor satisfactorily for both cloudy and sunny days. Using the above approach kinetic parameters independent of the radiation field in the reactor can be estimated directly from the results of experiments carried out in a solar CPC reactor. The SFM combined with reaction kinetics and fluid-dynamic models proved to be a simple, but reliable model, for solar photocatalytic applications.

Endocrine differences among colour morphs in a lizard with alternative behavioural strategies.

PubMed

Yewers, Madeleine St Clair; Jessop, Tim S; Stuart-Fox, Devi

2017-07-01

Alternative behavioural strategies of colour morphs are expected to associate with endocrine differences and to correspond to differences in physical performance (e.g. movement speed, bite force in lizards); yet the nature of correlated physiological and performance traits in colour polymorphic species varies widely. Colour morphs of male tawny dragon lizards Ctenophorus decresii have previously been found to differ in aggressive and anti-predator behaviours. We tested whether known behavioural differences correspond to differences in circulating baseline and post-capture stress levels of androgen and corticosterone, as well as bite force (an indicator of aggressive performance) and field body temperature. Immediately after capture, the aggressive orange morph had higher circulating androgen than the grey morph or the yellow morph. Furthermore, the orange morph maintained high androgen following acute stress (30min of capture); whereas androgen increased in the grey and yellow morphs. This may reflect the previously defined behavioural differences among morphs as the aggressive response of the yellow morph is conditional on the colour of the competitor and the grey morph shows consistently low aggression. In contrast, all morphs showed an increase in corticosterone concentration after capture stress and morphs did not differ in levels of corticosterone stress magnitude (CSM). Morphs did not differ in size- and temperature-corrected bite force but did in body temperature at capture. Differences in circulating androgen and body temperature are consistent with morph-specific behavioural strategies in C. decresii but our results indicate a complex relationship between hormones, behaviour, temperature and bite force within and between colour morphs. Copyright © 2017 Elsevier Inc. All rights reserved.

Lithium doped calcium phosphate cement maintains physical mechanical properties and promotes osteoblast proliferation and differentiation.

PubMed

Li, Li; Wang, Renchong; Li, Baichuan; Liang, Wei; Pan, Haobo; Cui, Xu; Tang, Jingli; Li, Bing

2017-07-01

Calcium phosphate cement (CPC) has been widely used in bone tissue repairing due to its physical mechanical properties and biocompatibility. Addition of trace element to CPC has shown promising evidence to improve the physical properties and biological activities of CPC. Lithium (Li) has effect on osteoblast proliferation and differentiation. In this study, we incorporated Li to CPC and examined the physical properties of Li/CPC and its effect on osteoblast proliferation and differentiation. We found that Li doped CPC maintained similar setting time, pore size distribution, compressive strength, composition, and morphology as CPC without Li. Additionally, Li doped CPC improved osteoblast proliferation and differentiation significantly compared to CPC without Li. To our knowledge, our results, for the first time, show that Li doped CPC has beneficial effect on osteoblast in cell culture while keeps the excellent physical-mechanical properties of CPC. This study will lead to potential application of Li doped CPC in bone tissue engineering. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 944-952, 2017. © 2016 Wiley Periodicals, Inc.

Variation in style morph frequencies in tristylous Lythrum salicaria in the Iberian Peninsula: the role of geographical and demographic factors

PubMed Central

Costa, Joana; Castro, Sílvia; Loureiro, João; Barrett, Spencer C. H.

2016-01-01

Background and Aims The balance between stochastic forces and negative frequency-dependent selection largely determines style morph frequencies in heterostylous populations. Investigation of morph frequencies at geographical range limits can provide insights into the forces maintaining the floral polymorphism, and the factors causing biased morph ratios. Here, we investigate style morph frequencies in populations at the south-western European range limit of tristylous Lythrum salicaria, to explore the role of demographic and geographical factors influencing morph ratios in its native range. Methods We measured morph composition and evenness, and the size of 96 populations, along a north to south latitudinal transect from Galicia to Andalucia, Iberian Peninsula, traversing a steep climatic gradient. To examine the potential influence of morph-specific fitness components on morph ratios, we examined reproductive traits in 19 populations. Key Results Most populations of L. salicaria were trimorphic (94·79 %), the majority exhibiting 1 : 1 : 1 morph ratios (68·75 %). Populations with biased morph ratios had a deficiency of the short-styled morph. Population size and morph evenness were positively associated with latitude, with smaller populations and those with less even morph ratios occurring towards the south. Greater variance in morph evenness was evident at the southern range margin. There were no consistent differences in components of reproductive fitness among style morphs, but southern populations produced less fruit and seed than more northerly populations. Conclusions Our results demonstrate the influence of finite population size on morph frequencies in L. salicaria. However, they also illustrate the resilience of Iberian populations to the factors causing deviations from isoplethy and morph loss, especially at the southern range limit where populations are smaller. The maintenance of tristyly in small populations of L. salicaria may be aided by the genetic connectivity of populations in agricultural landscapes resulting from gene flow through pollen and seed dispersal. PMID:26658100

Stem Cells and Calcium Phosphate Cement Scaffolds for Bone Regeneration

PubMed Central

Wang, P.; Zhao, L.; Chen, W.; Liu, X.; Weir, M.D.; Xu, H.H.K.

2014-01-01

Calcium phosphate cements (CPCs) have excellent biocompatibility and osteoconductivity for dental, craniofacial, and orthopedic applications. This article reviews recent developments in stem cell delivery via CPC for bone regeneration. This includes: (1) biofunctionalization of the CPC scaffold, (2) co-culturing of osteoblasts/endothelial cells and prevascularization of CPC, (3) seeding of CPC with different stem cell species, (4) human umbilical cord mesenchymal stem cell (hUCMSC) and bone marrow MSC (hBMSC) seeding on CPC for bone regeneration, and (5) human embryonic stem cell (hESC) and induced pluripotent stem cell (hiPSC) seeding with CPC for bone regeneration. Cells exhibited good attachment/proliferation in CPC scaffolds. Stem-cell-CPC constructs generated more new bone and blood vessels in vivo than did the CPC control without cells. hUCMSCs, hESC-MSCs, and hiPSC-MSCs in CPC generated new bone and blood vessels similar to those of hBMSCs; hence, they were viable cell sources for bone engineering. CPC with hESC-MSCs and hiPSC-MSCs generated new bone two- to three-fold that of the CPC control. Therefore, this article demonstrates that: (1) CPC scaffolds are suitable for delivering cells; (2) hUCMSCs, hESCs, and hiPSCs are promising alternatives to hBMSCs, which require invasive procedures to harvest with limited cell quantity; and (3) stem-cell-CPC constructs are highly promising for bone regeneration in dental, craniofacial, and orthopedic applications. PMID:24799422

The rock-paper-scissors game and the evolution of alternative male strategies

NASA Astrophysics Data System (ADS)

Sinervo, B.; Lively, C. M.

1996-03-01

MANY species exhibit colour polymorphisms associated with alternative male reproductive strategies, including territorial males and 'sneaker males' that behave and look like females1-3. The prevalence of multiple morphs is a challenge to evolutionary theory because a single strategy should prevail unless morphs have exactly equal fitness4,5 or a fitness advantage when rare6,7. We report here the application of an evolutionary stable strategy model to a three-morph mating system in the side-blotched lizard. Using parameter estimates from field data, the model predicted oscillations in morph frequency, and the frequencies of the three male morphs were found to oscillate over a six-year period in the field. The fitnesses of each morph relative to other morphs were non-transitive in that each morph could invade another morph when rare, but was itself invadable by another morph when common. Concordance between frequency-dependent selection and the among-year changes in morph fitnesses suggest that male interactions drive a dynamic 'rock-paper-scissors' game7.

Innovative Materials for Aircraft Morphing

NASA Technical Reports Server (NTRS)

Simpson, J. O.; Wise, S. A.; Bryant, R. G.; Cano, R. J.; Gates, T. S.; Hinkley, J. A.; Rogowski, R. S.; Whitley, K. S.

1997-01-01

Reported herein is an overview of the research being conducted within the Materials Division at NASA Langley Research Center on the development of smart material technologies for advanced airframe systems. The research is a part of the Aircraft Morphing Program which is a new six-year research program to develop smart components for self-adaptive airframe systems. The fundamental areas of materials research within the program are computational materials; advanced piezoelectric materials; advanced fiber optic sensing techniques; and fabrication of integrated composite structures. This paper presents a portion of the ongoing research in each of these areas of materials research.

[An experimental study on a slow-release complex with rifampicin-polylactic-co-glycolic acid-calcium 
phosphate cement].

PubMed

Wu, Jianhuang; Ding, Zhou; Lei, Qing; Li, Miao; Liang, Yan; Lu, Tao

2016-09-28

To prepare the slow-release complex with rifampicin (RFP)-polylactic-co-glycolic acid (PLGA)-calcium phosphate cement (CPC) (RFP-PLGA-CPC complex), and to study its physical and chemical properties and drug release properties in vitro.
 The emulsification-solvent evaporation method was adopted to prepare rifampicin polylactic acid-glycolic acid (RFP-PLGA) slow-release microspheres, which were divided into 3 groups: a calcium phosphate bone cement group (CPC group), a CPC embedded with RFP group (RFP-CPC group), and a PLGA slow-release microspheres carrying RFP and the self-curing CPC group (RFP- PLGA-CPC complex group). The solidification time and porosity of materials were determined. The drug release experiments in vitro were carried out to observe the compressive strength, the change of section morphology before and after drug release. 
 The CPC group showed the shortest solidification time, while the RFP-PLGA-CPC complex group had the longest one. There was statistical difference in the porosity between the CPC group and the RFP-CPC group (P<0.05); Compared to the RFP-PLGA-CPC complex group, the porosity in the CPC group and the RFP-CPC group were significantly changed (both P<0.01). There was significant difference in the compressive strength between the RFP- PLGA-CPC complex group and the CPC group (P<0.01), while there was significant difference in the compressive strength between the RFP-CPC group and the CPC group (3 days: P<0.05; 30 and 60 days: P<0.01). The change of the compressive strength in the CPC was not significant in the whole process of degradation. The sizes of PLGA microspheres were uniform, with the particle size between 100-150 μm. The microspheres were spheres or spheroids, and their surface was smooth without the attached impurities. There was no significant change in the section gap in the CPC group after soaking for 3 to 60 days. The microstructure change in the RFP-CPC group was small, and the cross section was formed by small particles. The pores of section in the RFP-PLGA-CPC complex group increased obviously, and PLGA microspheres gradually disappeared until the 60th day when there were only empty cavities left. The RFP-PLGA-CPC complex group had no obvious drugs sudden release, and the cumulative drug release rate was nearly 95% in the 60 days. The linear fitting was conducted for the drug release behavior of the complex, which was in accordance with zero order kinetics equation F=0.168×t.
 The porosity of RFP-PLGA-CPC complex is significantly higher than that of CPC, and it can keep slow release of the effective anti-tuberculosis drugs and maintain a certain mechanical strength for a long time.

Efficacy of the biomaterials 3wt%-nanostrontium-hydroxyapatite-enhanced calcium phosphate cement (nanoSr-CPC) and nanoSr-CPC-incorporated simvastatin-loaded poly(lactic-co-glycolic-acid) microspheres in osteogenesis improvement: An explorative multi-phase experimental in vitro/vivo study.

PubMed

Masaeli, Reza; Jafarzadeh Kashi, Tahereh Sadat; Dinarvand, Rassoul; Rakhshan, Vahid; Shahoon, Hossein; Hooshmand, Behzad; Mashhadi Abbas, Fatemeh; Raz, Majid; Rajabnejad, Alireza; Eslami, Hossein; Khoshroo, Kimia; Tahriri, Mohammadreza; Tayebi, Lobat

2016-12-01

The purpose of this multi-phase explorative in vivo animal/surgical and in vitro multi-test experimental study was to (1) create a 3wt%-nanostrontium hydroxyapatite-enhanced calcium phosphate cement (Sr-HA/CPC) for increasing bone formation and (2) creating a simvastatin-loaded poly(lactic-co-glycolic acid) (SIM-loaded PLGA) microspheres plus CPC composite (SIM-loaded PLGA+nanostrontium-CPC). The third goal was the extensive assessment of multiple in vitro and in vivo characteristics of the above experimental explorative products in vitro and in vivo (animal and surgical studies). Physical and chemical properties of the prepared Sr-HA/CPC were evaluated. MTT assay and alkaline phosphatase activities, and radiological and histological examinations of Sr-HA/CPC, CPC and negative control were compared. X-ray diffraction (XRD) indicated that crystallinity of the prepared cement increased by increasing the powder-to-liquid ratio. Incorporation of Sr-HA into CPC increased MTT assay (biocompatibility) and ALP activity (P<0.05). Histomorphometry showed greater bone formation after 4weeks, after implantation of Sr-HA/CPC in 10 rats compared to implantations of CPC or empty defects in the same rats (n=30, ANOVA P<0.05). METHODS AND RESULTS PERTAINING TO SIM-LOADED PLGA MICROSPHERES+NANOSTRONTIUM-CPC COMPOSITE: After SEM assessment, the produced composite of microspheres and enhanced CPC were implanted for 8weeks in 10 rabbits, along with positive and negative controls, enhanced CPC, and enhanced CPC plus SIM (n=50). In the control group, only a small amount of bone had been regenerated (localized at the boundary of the defect); whereas, other groups showed new bone formation within and around the materials. A significant difference was found in the osteogenesis induced by the groups sham control (16.96±1.01), bone materials (32.28±4.03), nanostrontium-CPC (24.84±2.6), nanostrontium-CPC-simvastatin (40.12±3.29), and SIM-loaded PLGA+nanostrontium-CPC (44.8±6.45) (ANOVA P<0.001). All the pairwise comparisons were significant (Tukey P<0.01), except that of nanostrontium-CPC-simvastatin and SIM-loaded PLGA+nanostrontium-CPC. This confirmed the efficacy of the SIM-loaded PLGA+nanostrontium-CPC composite, and its superiority over all materials except SIM-containing nanostrontium-CPC. Copyright © 2016 Elsevier B.V. All rights reserved.

Divergence of water balance mechanisms and acclimation potential in body color morphs of Drosophila ananassae.

PubMed

Parkash, Ravi; Aggarwal, Dau Dayal; Lambhod, Chanderkala; Singh, Divya

2014-01-01

Drosophila ananassae is a desiccation sensitive species, but the physiological basis of its abundance in the drier subtropical areas is largely unknown. We tested the hypothesis whether body color morphs of D. ananassae differ in the mechanistic basis of water conservation as well as desiccation acclimation potential, consistent with their distribution under dry or wet habitats. We observed reduced rate of water loss consistent with the greater desiccation potential of dark morph as compared with light morph, despite lack of quantitative differences in cuticular lipid mass between them. Dark morph evidenced greater wet and dry mass (∼1.17-fold) as well as higher hemolymph content (∼1.70-fold) and (∼17%) dehydration tolerance to sustain longer survival under desiccation stress (LT50 17.5 hr) as compared with light morph (LT50 4.3 hr). We found significant differences in the storage of energy metabolites in the body color morphs of D. ananassae, that is, carbohydrate content was significantly higher (∼0.18 mg/mg dry mass) in the dark morph as compared to light morph, but greater (∼0.05 mg/mg dry mass) body lipid content was evident in the light morph. Under desiccation stress, dark and light morphs utilized mainly carbohydrates but also lipids to a lesser extent. However, the rate of utilization of energy metabolites did not vary between dark and light morphs. Further, the dark morph consumed higher energy content derived from carbohydrates under desiccation stress as compared with the light morph. Finally, we found contrasting patterns of acclimation to desiccation stress in the two body color morphs, that is, increase in desiccation survival (4.7 hr), as well as in dehydration tolerance (∼6%) due to acclimation of the dark morph but no such effects were observed in the light morph. Thus, divergence in water balance mechanisms as well as acclimation potential reflects evolved physiological adaptations of the dark morph under drier but of the light morph to wet climatic conditions. © 2013 Wiley Periodicals, Inc.

Extending the time window for endovascular procedures according to collateral pial circulation.

PubMed

Ribo, Marc; Flores, Alan; Rubiera, Marta; Pagola, Jorge; Sargento-Freitas, Joao; Rodriguez-Luna, David; Coscojuela, Pilar; Maisterra, Olga; Piñeiro, Socorro; Romero, Francisco J; Alvarez-Sabin, Jose; Molina, Carlos A

2011-12-01

Good collateral pial circulation (CPC) predicts a favorable outcome in patients undergoing intra-arterial procedures. We aimed to determine if CPC status may be used to decide about pursuing recanalization efforts. Pial collateral score (0-5) was determined on initial angiogram. We considered good CPC when pial collateral score<3, defined total time of ischemia (TTI) as onset-to-recanalization time, and clinical improvement>4-point decline in admission-discharge National Institutes of Health Stroke Scale. We studied CPC in 61 patients (31 middle cerebral artery, 30 internal carotid artery). Good CPC patients (n=21 [34%]) had lower discharge National Institutes of Health Stroke Scale score (7 versus 21; P=0.02) and smaller infarcts (56 mL versus 238 mL; P<0.001). In poor CPC patients, a receiver operating characteristic curve defined a TTI cutoff point<300 minutes (sensitivity 67%, specificity 75%) that better predicted clinical improvement (TTI<300: 66.7% versus TTI>300: 25%; P=0.05). For good CPC patients, no temporal cutoff point could be defined. Although clinical improvement was similar for patients recanalizing within 300 minutes (poor CPC: 60% versus good CPC: 85.7%; P=0.35), the likelihood of clinical improvement was 3-fold higher after 300 minutes only in good CPC patients (23.1% versus 90.1%; P=0.01). Similarly, infarct volume was reduced 7-fold in good as compared with poor CPC patients only when TTI>300 minutes (TTI<300: poor CPC: 145 mL versus good CPC: 93 mL; P=0.56 and TTI>300: poor CPC: 217 mL versus good CPC: 33 mL; P<0.01). After adjusting for age and baseline National Institutes of Health Stroke Scale score, TTI<300 emerged as an independent predictor of clinical improvement in poor CPC patients (OR, 6.6; 95% CI, 1.01-44.3; P=0.05) but not in good CPC patients. In a logistic regression, good CPC independently predicted clinical improvement after adjusting for TTI, admission National Institutes of Health Stroke Scale score, and age (OR, 12.5; 95% CI, 1.6-74.8; P=0.016). Good CPC predicts better clinical response to intra-arterial treatment beyond 5 hours from onset. In patients with stroke receiving endovascular treatment, identification of good CPC may help physicians when considering pursuing recanalization efforts in late time windows.

EDITORIAL Smart materials, multifunctional composites, and morphing structures: selected papers from the 20th International Conference on Adaptive Structures and Technologies (ICAST 2009) Smart materials, multifunctional composites, and morphing structures: selected papers from the 20th International Conference on Adaptive Structures and Technologies (ICAST 2009)

NASA Astrophysics Data System (ADS)

Liao, Wei-Hsin

2010-12-01

The 20th International Conference on Adaptive Structures and Technologies (ICAST) was held on 20-22 October 2009 in Hong Kong. This special section of Smart Materials and Structures is derived from the research papers presented at the conference. Of the 106 papers presented at the conference, 11 papers were reviewed and accepted for this special section, following the regular review procedures of the journal. This special section is focused on smart materials, multifunctional composites, and applications on morphing structures. Smart materials. Smart materials are the foundation of adaptive structures and intelligent systems. The development of new materials will lead to significant improvement in various applications. Three articles are focused on the fabrication of new materials and investigation of their behaviors: Barium strontium zirconate titanate ((Ba1-xSrx)(ZrxTi1-x)O3; BSZT, x = 0.25 and 0.75) ceramics with a highly crystalline structure were fabricated using the combustion technique. The microstructure of BSZT powders exhibited an almost-spherical morphology and had a porous agglomerated form. Polyaniline (PANI)/clay nanoparticles with unique core-shell structure were synthesized via Pickering emulsion polymerization. By dispersing PANI/clay nanoparticles in silicone oil, the ER fluid was made. Magnetic field effects were investigated on the deposition rate and surface morphology of chromium nitride coatings deposited by magnetron sputtering for superior hardness, excellent wear and oxidation resistance. The surface morphology of chromium nitride films was also examined by a scanning electron microscope (SEM). Multifunctional composites. Composites are made from two or more constituent materials so they can combine the best properties of different materials. Five papers deal with fabrication, testing, and modeling of various multifunctional composites: A new active structural fiber (ASF) was fabricated by coating a single carbon fiber with a concentric PZT (PbZr0.52Ti0.48O3) shell using electrolytic deposition. This new ASF is expected to have broader applications due to the higher piezoelectric coupling effect with the use of carbon fiber and PZT. The sol-gel technique was employed to deposit lead zirconium titanium (PZT) and silica composite film onto a copper (Cu)/polyimide (PI) flexible structure. The fabricated PZT-silica composite films were then used for flexible actuator and sensor applications. Interfacial properties and hydrophobicity of multifunctional Ni-nanopowder/epoxy composites were evaluated for self-sensing and actuation. The effects of water content on the actuation performance of ionic polymer-metal composites (IPMCs) were investigated experimentally. Multiscale modelling of a composite electroactive polymer structure was developed, in particular for tubular actuators. The models were validated with experimental data. Morphing structures. Three papers relate to morphing skins and structures. Several issues including stiffness and energy consumption were explored: Composite corrugated structures were used as morphing skin panels (MSPs) in the trailing edge region of a scaled morphing aerofoil section. Wind tunnel testing was carried out to demonstrate the MSP concept. Optimization of a variable-stiffness skin was performed for morphing high-lift devices. The objective is to design the structure to have high enough stiffness to withstand aerodynamic loading and yet low enough stiffness to enable morphing. The aerodynamic and actuation loads were taken into consideration during the optimization. Two adaptive and morphing structures were proposed for low-energy consumption or even energy-harvesting green buildings with the use of an optimization process. Searching for optimal solutions was done by means of an evolutionary technique while the compatibility of the resulting configurations of the adaptive envelope was ensured by the virtual force density method. We would like to thank all of the authors for their significant contributions to this special section for Smart Materials and Structures. We are also grateful to all of the reviewers and associate editors who handled the reviews for their time and effort. I would like to express my sincere appreciation to Professor E Garcia, Editor-in-Chief, for his encouragement by providing the opportunity to make this special section. I am indebted to IOP Publishing for their strong support and the staff, in particular publisher Natasha Leeper, for their special attention and excellent service.

A mathematical procedure to predict optical performance of CPCs

NASA Astrophysics Data System (ADS)

Yu, Y. M.; Yu, M. J.; Tang, R. S.

2016-08-01

To evaluate the optical performance of a CPC based concentrating photovoltaic system, it is essential to find the angular dependence of optical efficiency of compound parabolic concentrator (CPC-θe ) where the incident angle of solar rays on solar cells is restricted within θe for the radiation over its acceptance angle. In this work, a mathematical procedure was developed to calculate the optical efficiency of CPC-θe for radiation incident at any angle based radiation transfer within CPC-θe . Calculations show that, given the acceptance half-angle (θa ), the annual radiation of full CPC-θe increases with the increase of θe and the CPC without restriction of exit angle (CPC-90) annually collects the most radiation due to large geometry (Ct ); whereas for truncated CPCs with identical θa and Ct , the annual radiation collected by CPC-θe is almost identical to that by CPC-90, even slightly higher. Calculations also indicate that the annual radiation on the absorber of CPC-θe at the angle larger than θe decrease with the increase of θe but always less than that of CPC-90, and this implies that the CPC-θe based PV system is more efficient than CPC-90 based PV system because the radiation on solar cells incident at large angle is poorly converted into electricity.

[Experimental study of canine bone marrow mesenchymal stem cells combined with calcium phosphate cement for repair of mandibular bone defects in Beagle dogs].

PubMed

Hu, Yi-cheng; Liu, Xin; Shen, Ji-jia; He, Jia-cai; Chen, Qiao-er

2014-08-01

To evaluate the effects of bone marrow mesenchymal stem cells (BMSCs) combined with calcium phosphate cement (CPC) scaffold for repair of mandibular defect in Beagle dogs. BMSCs were isolated from Beagle dogs and cultured in DMEM plus 10% FBS. The induction effect was determined using alizarin red staining or alkaline phosphate staining at 14-day of culture. BMSCs were added to the CPC scaffold for animal experiments. In vivo, three critical size bone defects were surgically created in each side of the mandible. The bone defects were repaired with BMSCs-CPC (scaffolds with composite seeding cells), CPC (scaffold alone) or no materials (blank group). Two dogs were sacrificed at 4-week and 8-week after operation. Gross observation, X-ray imaging, histologic and histometric analyses were performed to evaluate the level of bone formation. Newly formed bones were detected within all defect sites after operation. The BMSCs-CPC group and CPC group showed increased bone formation compared with the blank group. The BMSCs-CPC group exhibited more bone formation and degradation of the material than the CPC group. The percentage of new bone in the BMSCs-CPC and CPC treated group were significantly higher than that in the control group (P<0.05), while the percentage of new bone in the BMSCs-CPC sites was higher than that in the CPC sites (P<0.01); the percentage of residual material in the BMSCs-CPC sites was lower than that in the CPC sites (P<0.01) 4 weeks and 8 weeks after operation. Using the theory of tissue engineering, BMSCs composite CPC compound is an effective method in promoting new bone regeneration, which has a positive influence on the bone space preservation.

Determination of the Inactivating Alterations in Two Mutant Alleles of the Neurospora Crassa Cross-Pathway Control Gene Cpc-1

PubMed Central

Paluh, J. L.; Plamann, M.; Kruger, D.; Barthelmess, I. B.; Yanofsky, C.; Perkins, D. D.

1990-01-01

cpc-1 is the locus specifying what is believed to be the major trans-activating transcription factor that regulates expression of amino acid biosynthetic genes subject to cross-pathway control in Neurospora crassa. Mutants altered at this locus are incapable of the global increase in gene expression normally seen in response to amino acid starvation. Using polymerase chain reaction methodology we have cloned and sequenced the inactive mutant allele, cpc-1 (CD15). The cpc-1 (CD15) mutation was found to be a single base pair deletion in codon 93 of the cpc-1 structural gene. A second, presumed lethal, allele, cpc-1 (j-5), also was investigated. Northern analyses with strains carrying the cpc-1 (j-5) allele revealed that no cpc-1 mRNA is produced. Southern and genetic analyses established that the cpc-1 (j-5) mutation involved a chromosomal rearrangement in which a break occurred within the cpc-1 locus, normally resident on linkage group VI; a small fragment from the left arm of linkage group VI, containing the cpc-1 promoter region and ylo-1, was translocated to the right arm of linkage group I. Other studies indicate that the cpc-1 locus itself is not essential for viability. Lethality previously attributed to the cpc-1 (j-5) mutation is due instead to the production of progeny that are deficient for essential genes in an adjoining segment of linkage group VI. Molecular characterization of cpc-1 (j-5) X ylo-1 pan-2 duplication progeny indicated that cpc-1 is normally transcribed towards the linkage group VI centromere. PMID:2138111

Pollinator visitation in populations of tristylous Eichhornia paniculata in northeastern Brazil.

PubMed

Husband, Brian C; Barrett, Spencer C H

1992-03-01

The frequencies of floral morphs in populations of tristylous Eichhornia paniculata often deviate from the theoretical expectation of equality. This variation is associated with the breakdown of tristyly and the evolution of self-fertilization. Differences in morph frequencies could result from selection pressures due to variable levels of insect visitation to populations and contrasting foraging behavior among the floral morphs. We estimated pollinator densities in 16 populations and quantified visitation sequences to morphs in five populations of E. paniculata in northeastern Brazil. Foraging behavior among floral morphs was measured as the frequency of visits to morphs relative to their frequency in the population (preference) and number of flights between inflorescences of the same versus different morphs (constancy). Pollinator density (number/m 2 /minute) was not correlated with population size, plant density or morph diversity. Pollinator densities varied most among populations of less than 200 plants. Whether pollinators discriminated among the morphs, depended on whether they primarily collected nectar or pollen. In four populations, nectar-feeding bees (Ancyloscelis and Florilegus spp.) and butterflies showed no consistent preference or constancy among the morphs. In contrast, pollen-collecting bees (Trigona sp.) visited a lower proportion of longstyled inflorescences than expected and tended to visit more mid-and short-styled inflorescences in succession, once they were encountered. Pollinator constancy for morphs did not result from differences in inflorescence production or spatial patchiness among the morphs. Although non-random pollinator visitation to morphs in heterostylous populations could potentially affect mating and hence morph frequencies, the observed visitation patterns in this study do not provide evidence that pollinators play a major role in influencing floral morph frequencies.

A methodology to accurately quantify patellofemoral cartilage contact kinematics by combining 3D image shape registration and cine-PC MRI velocity data.

PubMed

Borotikar, Bhushan S; Sipprell, William H; Wible, Emily E; Sheehan, Frances T

2012-04-05

Patellofemoral osteoarthritis and its potential precursor patellofemoral pain syndrome (PFPS) are common, costly, and debilitating diseases. PFPS has been shown to be associated with altered patellofemoral joint mechanics; however, an actual variation in joint contact stresses has not been established due to challenges in accurately quantifying in vivo contact kinematics (area and location). This study developed and validated a method for tracking dynamic, in vivo cartilage contact kinematics by combining three magnetic resonance imaging (MRI) techniques, cine-phase contrast (CPC), multi-plane cine (MPC), and 3D high-resolution static imaging. CPC and MPC data were acquired from 12 healthy volunteers while they actively extended/flexed their knee within the MRI scanner. Since no gold standard exists for the quantification of in vivo dynamic cartilage contact kinematics, the accuracy of tracking a single point (patellar origin relative to the femur) represented the accuracy of tracking the kinematics of an entire surface. The accuracy was determined by the average absolute error between the PF kinematics derived through registration of MPC images to a static model and those derived through integration of the CPC velocity data. The accuracy ranged from 0.47 mm to 0.77 mm for the patella and femur and from 0.68 mm to 0.86 mm for the patellofemoral joint. For purely quantifying joint kinematics, CPC remains an analytically simpler and more accurate (accuracy <0.33 mm) technique. However, for application requiring the tracking of an entire surface, such as quantifying cartilage contact kinematics, this combined imaging approach produces accurate results with minimal operator intervention. Published by Elsevier Ltd.

A Novel Injectable Calcium Phosphate Cement-Bioactive Glass Composite for Bone Regeneration

PubMed Central

Zhao, Kang; Tang, Yufei; Cheng, Zhe; Chen, Jun; Zang, Yuan; Wu, Jianwei; Kong, Liang; Liu, Shuai; Lei, Wei; Wu, Zixiang

2013-01-01

Background Calcium phosphate cement (CPC) can be molded or injected to form a scaffold in situ, which intimately conforms to complex bone defects. Bioactive glass (BG) is known for its unique ability to bond to living bone and promote bone growth. However, it was not until recently that literature was available regarding CPC-BG applied as an injectable graft. In this paper, we reported a novel injectable CPC-BG composite with improved properties caused by the incorporation of BG into CPC. Materials and Methods The novel injectable bioactive cement was evaluated to determine its composition, microstructure, setting time, injectability, compressive strength and behavior in a simulated body fluid (SBF). The in vitro cellular responses of osteoblasts and in vivo tissue responses after the implantation of CPC-BG in femoral condyle defects of rabbits were also investigated. Results CPC-BG possessed a retarded setting time and markedly better injectability and mechanical properties than CPC. Moreover, a new Ca-deficient apatite layer was deposited on the composite surface after immersing immersion in SBF for 7 days. CPC-BG samples showed significantly improved degradability and bioactivity compared to CPC in simulated body fluid (SBF). In addition, the degrees of cell attachment, proliferation and differentiation on CPC-BG were higher than those on CPC. Macroscopic evaluation, histological evaluation, and micro-computed tomography (micro-CT) analysis showed that CPC-BG enhanced the efficiency of new bone formation in comparison with CPC. Conclusions A novel CPC-BG composite has been synthesized with improved properties exhibiting promising prospects for bone regeneration. PMID:23638115

Radiation absorption and optimization of solar photocatalytic reactors for environmental applications.

PubMed

Colina-Márquez, Jose; Machuca-Martínez, Fiderman; Li Puma, Gianluca

2010-07-01

This study provides a systematic and quantitative approach to the analysis and optimization of solar photocatalytic reactors utilized in environmental applications such as pollutant remediation and conversion of biomass (waste) to hydrogen. Ray tracing technique was coupled with the six-flux absorption scattering model (SFM) to analyze the complex radiation field in solar compound parabolic collectors (CPC) and tubular photoreactors. The absorption of solar radiation represented by the spatial distribution of the local volumetric rate of photon absorption (LVRPA) depends strongly on catalyst loading and geometry. The total radiation absorbed in the reactors, the volumetric rate of absorption (VRPA), was analyzed as a function of the optical properties (scattering albedo) of the photocatalyst. The VRPA reached maxima at specific catalyst concentrations in close agreement with literature experimental studies. The CPC has on average 70% higher photon absorption efficiency than a tubular reactor and requires 39% less catalyst to operate under optimum conditions. The "apparent optical thickness" is proposed as a new dimensionless parameter for optimization of CPC and tubular reactors. It removes the dependence of the optimum catalyst concentration on tube diameter and photocatalyst scattering albedo. For titanium dioxide (TiO(2)) Degussa P25, maximum photon absorption occurs at apparent optical thicknesses of 7.78 for CPC and 12.97 for tubular reactors.

Patient specific computerized phantoms to estimate dose in pediatric CT

NASA Astrophysics Data System (ADS)

Segars, W. P.; Sturgeon, G.; Li, X.; Cheng, L.; Ceritoglu, C.; Ratnanather, J. T.; Miller, M. I.; Tsui, B. M. W.; Frush, D.; Samei, E.

2009-02-01

We create a series of detailed computerized phantoms to estimate patient organ and effective dose in pediatric CT and investigate techniques for efficiently creating patient-specific phantoms based on imaging data. The initial anatomy of each phantom was previously developed based on manual segmentation of pediatric CT data. Each phantom was extended to include a more detailed anatomy based on morphing an existing adult phantom in our laboratory to match the framework (based on segmentation) defined for the target pediatric model. By morphing a template anatomy to match the patient data in the LDDMM framework, it was possible to create a patient specific phantom with many anatomical structures, some not visible in the CT data. The adult models contain thousands of defined structures that were transformed to define them in each pediatric anatomy. The accuracy of this method, under different conditions, was tested using a known voxelized phantom as the target. Errors were measured in terms of a distance map between the predicted organ surfaces and the known ones. We also compared calculated dose measurements to see the effect of different magnitudes of errors in morphing. Despite some variations in organ geometry, dose measurements from morphing predictions were found to agree with those calculated from the voxelized phantom thus demonstrating the feasibility of our methods.

Design, realization and structural testing of a compliant adaptable wing

NASA Astrophysics Data System (ADS)

Molinari, G.; Quack, M.; Arrieta, A. F.; Morari, M.; Ermanni, P.

2015-10-01

This paper presents the design, optimization, realization and testing of a novel wing morphing concept, based on distributed compliance structures, and actuated by piezoelectric elements. The adaptive wing features ribs with a selectively compliant inner structure, numerically optimized to achieve aerodynamically efficient shape changes while simultaneously withstanding aeroelastic loads. The static and dynamic aeroelastic behavior of the wing, and the effect of activating the actuators, is assessed by means of coupled 3D aerodynamic and structural simulations. To demonstrate the capabilities of the proposed morphing concept and optimization procedure, the wings of a model airplane are designed and manufactured according to the presented approach. The goal is to replace conventional ailerons, thus to achieve controllability in roll purely by morphing. The mechanical properties of the manufactured components are characterized experimentally, and used to create a refined and correlated finite element model. The overall stiffness, strength, and actuation capabilities are experimentally tested and successfully compared with the numerical prediction. To counteract the nonlinear hysteretic behavior of the piezoelectric actuators, a closed-loop controller is implemented, and its capability of accurately achieving the desired shape adaptation is evaluated experimentally. Using the correlated finite element model, the aeroelastic behavior of the manufactured wing is simulated, showing that the morphing concept can provide sufficient roll authority to allow controllability of the flight. The additional degrees of freedom offered by morphing can be also used to vary the plane lift coefficient, similarly to conventional flaps. The efficiency improvements offered by this technique are evaluated numerically, and compared to the performance of a rigid wing.

Optimization of a tensegrity wing for biomimetic applications

NASA Astrophysics Data System (ADS)

Moored, Keith W., III; Taylor, Stuart A.; Bart-Smith, Hilary

2006-03-01

Current attempts to build fast, efficient, and maneuverable underwater vehicles have looked to nature for inspiration. However, they have all been based on traditional propulsive techniques, i.e. rotary motors. In the current study a promising and potentially revolutionary approach is taken that overcomes the limitations of these traditional methods-morphing structure concepts with integrated actuation and sensing. Inspiration for this work comes from the manta ray (Manta birostris) and other batoid fish. These creatures are highly maneuverable but are also able to cruise at high speeds over long distances. In this paper, the structural foundation for the biomimetic morphing wing is a tensegrity structure. A preliminary procedure is presented for developing morphing tensegrity structures that include actuating elements. A shape optimization method is used that determines actuator placement and actuation amount necessary to achieve the measured biological displacement field of a ray. Lastly, an experimental manta ray wing is presented that measures the static and dynamic pressure field acting on the ray's wings during a normal flapping cycle.

Effect of proteins and their conformation change during brushite transformation to hydroxyapatite

NASA Astrophysics Data System (ADS)

Xie, Jing

2000-10-01

Hydroxyapatite (HA, Ca5(PO4)3OH) coatings on metallic orthopedic implant are being used to achieve implant integration. However, HA is stable in physiological solutions, other more reactive calcium phosphate ceramics (CPC) such as brushite (CaHPO4·2H 2O) have been found to release calcium and phosphate ions during their transformation to HA. The release of these ions may induce faster bone growth and enhance implant integration. This work examines the biocompatibility of the CPC phases that form during the transformation process. Since biocompatibility is associated with cellular response, which in turn is initiated by protein adsorption, this work focuses on the mutual effect between protein adsorption and CPC transformation. The first part of the study is focused on the influence of protein adsorption on transformation kinetics and chemistry. Brushite coated samples immersed in protein free and proteinaceous physiological solutions were retrieved after different exposures times. These were examined using XRD, EDS and FTIR/reflectance. Results show that the presence of Bovine Serum Albumin (BSA) in physiological solution retards the transformation, but the presence of Fibronectin (FN) accelerates the transformation to HA. Interestingly, neither BSA nor FN alters the transformation chemistry. Due to the limitations of the techniques used, this part of the work does not monitor the effect of transformation on adsorbed proteins but only the effect of adsorbed protein on the transforming calcium phosphate coating. The second part of the work examines in situ conformational changes of adsorbed proteins during the CPC transformation using FTIR/ATR. Protein adsorbed on different surfaces such as germanium, CPC, zinc selenide and titanium shows different conformation indicated by the Amide I and II absorption bands in the infrared spectra. During the transformation of brushite to HA, both BSA and FN show a continuous change in conformation, which suggests that the transformation of CPC coating influences adsorbed protein structure.

Morphological divergence between three Arctic charr morphs - the significance of the deep-water environment.

PubMed

Skoglund, Sigrid; Siwertsson, Anna; Amundsen, Per-Arne; Knudsen, Rune

2015-08-01

Morphological divergence was evident among three sympatric morphs of Arctic charr (Salvelinus alpinus (L.)) that are ecologically diverged along the shallow-, deep-water resource axis in a subarctic postglacial lake (Norway). The two deep-water (profundal) spawning morphs, a benthivore (PB-morph) and a piscivore (PP-morph), have evolved under identical abiotic conditions with constant low light and temperature levels in their deep-water habitat, and were morphologically most similar. However, they differed in important head traits (e.g., eye and mouth size) related to their different diet specializations. The small-sized PB-morph had a paedomorphic appearance with a blunt head shape, large eyes, and a deep body shape adapted to their profundal lifestyle feeding on submerged benthos from soft, deep-water sediments. The PP-morph had a robust head, large mouth with numerous teeth, and an elongated body shape strongly related to their piscivorous behavior. The littoral spawning omnivore morph (LO-morph) predominantly utilizes the shallow benthic-pelagic habitat and food resources. Compared to the deep-water morphs, the LO-morph had smaller head relative to body size. The LO-morph exhibited traits typical for both shallow-water benthic feeding (e.g., large body depths and small eyes) and planktivorous feeding in the pelagic habitat (e.g., streamlined body shape and small mouth). The development of morphological differences within the same deep-water habitat for the PB- and PP-morphs highlights the potential of biotic factors and ecological interactions to promote further divergence in the evolution of polymorphism in a tentative incipient speciation process. The diversity of deep-water charr in this study represents a novelty in the Arctic charr polymorphism as a truly deep-water piscivore morph has to our knowledge not been described elsewhere.

Evaluation of Bias Correction Method for Satellite-Based Rainfall Data

PubMed Central

Bhatti, Haris Akram; Rientjes, Tom; Haile, Alemseged Tamiru; Habib, Emad; Verhoef, Wouter

2016-01-01

With the advances in remote sensing technology, satellite-based rainfall estimates are gaining attraction in the field of hydrology, particularly in rainfall-runoff modeling. Since estimates are affected by errors correction is required. In this study, we tested the high resolution National Oceanic and Atmospheric Administration’s (NOAA) Climate Prediction Centre (CPC) morphing technique (CMORPH) satellite rainfall product (CMORPH) in the Gilgel Abbey catchment, Ethiopia. CMORPH data at 8 km-30 min resolution is aggregated to daily to match in-situ observations for the period 2003–2010. Study objectives are to assess bias of the satellite estimates, to identify optimum window size for application of bias correction and to test effectiveness of bias correction. Bias correction factors are calculated for moving window (MW) sizes and for sequential windows (SW’s) of 3, 5, 7, 9, …, 31 days with the aim to assess error distribution between the in-situ observations and CMORPH estimates. We tested forward, central and backward window (FW, CW and BW) schemes to assess the effect of time integration on accumulated rainfall. Accuracy of cumulative rainfall depth is assessed by Root Mean Squared Error (RMSE). To systematically correct all CMORPH estimates, station based bias factors are spatially interpolated to yield a bias factor map. Reliability of interpolation is assessed by cross validation. The uncorrected CMORPH rainfall images are multiplied by the interpolated bias map to result in bias corrected CMORPH estimates. Findings are evaluated by RMSE, correlation coefficient (r) and standard deviation (SD). Results showed existence of bias in the CMORPH rainfall. It is found that the 7 days SW approach performs best for bias correction of CMORPH rainfall. The outcome of this study showed the efficiency of our bias correction approach. PMID:27314363

Evaluation of Bias Correction Method for Satellite-Based Rainfall Data.

PubMed

Bhatti, Haris Akram; Rientjes, Tom; Haile, Alemseged Tamiru; Habib, Emad; Verhoef, Wouter

2016-06-15

With the advances in remote sensing technology, satellite-based rainfall estimates are gaining attraction in the field of hydrology, particularly in rainfall-runoff modeling. Since estimates are affected by errors correction is required. In this study, we tested the high resolution National Oceanic and Atmospheric Administration's (NOAA) Climate Prediction Centre (CPC) morphing technique (CMORPH) satellite rainfall product (CMORPH) in the Gilgel Abbey catchment, Ethiopia. CMORPH data at 8 km-30 min resolution is aggregated to daily to match in-situ observations for the period 2003-2010. Study objectives are to assess bias of the satellite estimates, to identify optimum window size for application of bias correction and to test effectiveness of bias correction. Bias correction factors are calculated for moving window (MW) sizes and for sequential windows (SW's) of 3, 5, 7, 9, …, 31 days with the aim to assess error distribution between the in-situ observations and CMORPH estimates. We tested forward, central and backward window (FW, CW and BW) schemes to assess the effect of time integration on accumulated rainfall. Accuracy of cumulative rainfall depth is assessed by Root Mean Squared Error (RMSE). To systematically correct all CMORPH estimates, station based bias factors are spatially interpolated to yield a bias factor map. Reliability of interpolation is assessed by cross validation. The uncorrected CMORPH rainfall images are multiplied by the interpolated bias map to result in bias corrected CMORPH estimates. Findings are evaluated by RMSE, correlation coefficient (r) and standard deviation (SD). Results showed existence of bias in the CMORPH rainfall. It is found that the 7 days SW approach performs best for bias correction of CMORPH rainfall. The outcome of this study showed the efficiency of our bias correction approach.

Remote sensing-based characterization of rainfall during atmospheric rivers over the central United States

NASA Astrophysics Data System (ADS)

Nayak, Munir A.; Villarini, Gabriele

2018-01-01

Atmospheric rivers (ARs) play a central role in the hydrology and hydroclimatology of the central United States. More than 25% of the annual rainfall is associated with ARs over much of this region, with many large flood events tied to their occurrence. Despite the relevance of these storms for flood hydrology and water budget, the characteristics of rainfall associated with ARs over the central United has not been investigated thus far. This study fills this major scientific gap by describing the rainfall during ARs over the central United States using five remote sensing-based precipitation products over a 12-year study period. The products we consider are: Stage IV, Tropical Rainfall Measuring Mission - Multi-satellite Precipitation Analysis (TMPA, both real-time and research version); Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks (PERSIANN); the CPC MORPHing Technique (CMORPH). As part of the study, we evaluate these products against a rain gauge-based dataset using both graphical- and metrics-based diagnostics. Based on our analyses, Stage IV is found to better reproduce the reference data. Hence, we use it for the characterization of rainfall in ARs. Most of the AR-rainfall is located in a narrow region within ∼150 km on both sides of the AR major axis. In this region, rainfall has a pronounced positive relationship with the magnitude of the water vapor transport. Moreover, we have also identified a consistent increase in rainfall intensity with duration (or persistence) of AR conditions. However, there is not a strong indication of diurnal variability in AR rainfall. These results can be directly used in developing flood protection strategies during ARs. Further, weather prediction agencies can benefit from the results of this study to achieve higher skill of resolving precipitation processes in their models.

Geographically weighted regression based methods for merging satellite and gauge precipitation

NASA Astrophysics Data System (ADS)

Chao, Lijun; Zhang, Ke; Li, Zhijia; Zhu, Yuelong; Wang, Jingfeng; Yu, Zhongbo

2018-03-01

Real-time precipitation data with high spatiotemporal resolutions are crucial for accurate hydrological forecasting. To improve the spatial resolution and quality of satellite precipitation, a three-step satellite and gauge precipitation merging method was formulated in this study: (1) bilinear interpolation is first applied to downscale coarser satellite precipitation to a finer resolution (PS); (2) the (mixed) geographically weighted regression methods coupled with a weighting function are then used to estimate biases of PS as functions of gauge observations (PO) and PS; and (3) biases of PS are finally corrected to produce a merged precipitation product. Based on the above framework, eight algorithms, a combination of two geographically weighted regression methods and four weighting functions, are developed to merge CMORPH (CPC MORPHing technique) precipitation with station observations on a daily scale in the Ziwuhe Basin of China. The geographical variables (elevation, slope, aspect, surface roughness, and distance to the coastline) and a meteorological variable (wind speed) were used for merging precipitation to avoid the artificial spatial autocorrelation resulting from traditional interpolation methods. The results show that the combination of the MGWR and BI-square function (MGWR-BI) has the best performance (R = 0.863 and RMSE = 7.273 mm/day) among the eight algorithms. The MGWR-BI algorithm was then applied to produce hourly merged precipitation product. Compared to the original CMORPH product (R = 0.208 and RMSE = 1.208 mm/hr), the quality of the merged data is significantly higher (R = 0.724 and RMSE = 0.706 mm/hr). The developed merging method not only improves the spatial resolution and quality of the satellite product but also is easy to implement, which is valuable for hydrological modeling and other applications.

Purification of the photosynthetic pigment C-phycocyanin from heterotrophic Galdieria sulphuraria.

PubMed

Sørensen, Laila; Hantke, Andrea; Eriksen, Niels T

2013-09-01

The phycobiliprotein C-phycocyanin (C-PC) is used in cosmetics, diagnostics and foods and also as a nutraceutical or biopharmaceutical. It is produced in the cyanobacterium Arthrospira platensis grown phototrophically in open cultures. C-PC may alternatively be produced heterotrophically in the unicellular rhodophyte Galdieria sulphuraria at higher productivities and under improved hygienic standards if it can be purified as efficiently as C-PC from A. platensis. Ammonium sulfate fractionation, aqueous two-phase extraction, tangential flow ultrafiltration and anion exchange chromatography were evaluated with respect to the purification of C-PC from G. sulphuraria extracts. Galdieria sulphuraria C-PC showed similar properties to those described for cyanobacterial C-PC with respect to separation by all methodologies. The presence of micelles in G. sulphuraria extracts influenced the different procedures. Only chromatography was able to separate C-PC from a second phycobiliprotein, allophycocyanin. C-PC from heterotrophic G. sulphuraria shows similar properties to cyanobacterial C-PC and can be purified to the same standards, despite initial C-PC concentrations being low and impurity concentrations high in G. sulphuraria extracts. © 2013 Society of Chemical Industry.

Morphing Wings: A Study Using High-Fidelity Aerodynamic Shape Optimization

NASA Astrophysics Data System (ADS)

Curiale, Nathanael J.

With the aviation industry under pressure to reduce fuel consumption, morphing wings have the capacity to improve aircraft performance, thereby making a significant contribution to reversing climate change. Through high-fidelity aerodynamic shape optimization, various forms of morphing wings are assessed for a hypothetical regional-class aircraft. The framework used solves the Reynolds-averaged Navier-Stokes equations and utilizes a gradient-based optimization algorithm. Baseline geometries are developed through multipoint optimization, where the average drag coefficient is minimized over a range of flight conditions with additional dive constraints. Morphing optimizations are then performed, beginning with these baseline shapes. Five distinct types of morphing are investigated and compared. Overall, a theoretical fully adaptable wing produces roughly a 2% improvement in average performance, whereas trailing-edge morphing with a 27-point multipoint baseline results in just over a 1% improvement in average performance. Trailing-edge morphing proves to be more beneficial than leading-edge morphing, upper-surface morphing, and a conventional flap.

Amino acid substitution converts WEREWOLF function from an activator to a repressor of Arabidopsis non-hair cell development.

PubMed

Tominaga-Wada, Rumi; Nukumizu, Yuka; Wada, Takuji

2012-02-01

Root hair cell or non-hair cell fate determination in Arabidopsis thaliana root epidermis is model system for plant cell development. Two types of MYB transcription factors, the R2R3-type MYB, WEREWOLF (WER), and an R3-type MYB, CAPRICE (CPC), are involved in this cell fate determination process. To study the molecular basis of this process, we analyzed the functional relationship of WER and CPC. WER-CPC chimeric constructs were made from WER where all or parts of the MYB R3 region were replaced with the corresponding regions from CPC R3, and the constructs were introduced into the cpc-2 mutant. Although, the WER gene did not rescue the cpc-2 mutant 'small number of root hairs' phenotype, the WER-CPC chimera with two amino acids substitution (WC6) completely rescued the cpc-2 mutant phenotype. Furthermore, the WER-CPC chimera with 37 amino acids substitution (WC5) excessively rescued the cpc-2 mutant and induced 2.5 times more root hairs than wild-type. Consistent with this phenotype, GL2 gene expression was strongly reduced in WC5 in a cpc-2 background. Our results suggest that swapping at least two amino acids is sufficient to convert WER to CPC function. Therefore, these key residues may have strongly contributed to the selection of these important functions over evolution. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Effect of a muscle relaxant, chlorphenesin carbamate, on the spinal neurons of rats.

PubMed

Kurachi, M; Aihara, H

1984-09-01

The effects of chlorphenesin carbamate (CPC) and mephenesin on spinal neurons were investigated in spinal rats. CPC (50 mg/kg i.v.) inhibited the mono-(MSR) and poly-synaptic reflex (PSR), the latter being more susceptible than the former to CPC depression. Mephenesin also inhibited MSR and PSR, though the effects were short in duration. CPC had no effect on the dorsal root potential evoked by the stimulation of the dorsal root, while mephenesin reduced the dorsal root-dorsal root reflex. The excitability of motoneuron was reduced by the administration of CPC or mephenesin. The excitability of primary afferent terminal was unchanged by CPC, while it was inhibited by mephenesin. Neither CPC nor mephenesin influenced the field potential evoked by the dorsal root stimulation. Both CPC and mephenesin had no effect on the synaptic recovery. These results suggest that both CPC and mephenesin inhibit the firing of motoneurons by stabilizing the neuronal membrane, while mephenesin additionally suppresses the dorsal root reflex and the excitability of the primary afferent terminal. These inhibitory actions of CPC on spinal activities may contribute, at least partly, to its muscle relaxing action.

Antimelanogenic effect of c-phycocyanin through modulation of tyrosinase expression by upregulation of ERK and downregulation of p38 MAPK signaling pathways

PubMed Central

2011-01-01

Background Pigmentation is one of the essential defense mechanisms against oxidative stress or UV irradiation; however, abnormal hyperpigmentation in human skin may pose a serious aesthetic problem. C-phycocyanin (Cpc) is a phycobiliprotein from spirulina and functions as an antioxidant and a light harvesting protein. Though it is known that spirulina has been used to reduce hyperpigmentation, little literature addresses the antimelanogenic mechanism of Cpc. Herein, we investigated the rationale for the Cpc-induced inhibitory mechanism on melanin synthesis in B16F10 melanoma cells. Methods Cpc-induced inhibitory effects on melanin synthesis and tyrosinase expression were evaluated. The activity of MAPK pathways-associated molecules such as MAPK/ERK and p38 MAPK, were also examined to explore Cpc-induced antimelanogenic mechanisms. Additionally, the intracellular localization of Cpc was investigated by confocal microscopic analysis to observe the migration of Cpc. Results Cpc significantly (P < 0.05) reduced both tyrosinase activity and melanin production in a dose-dependent manner. This phycobiliprotein elevated the abundance of intracellular cAMP leading to the promotion of downstream ERK1/2 phosphorylation and the subsequent MITF (the transcription factor of tyrosinase) degradation. Further, Cpc also suppressed the activation of p38 causing the consequent disturbed activation of CREB (the transcription factor of MITF). As a result, Cpc negatively regulated tyrosinase gene expression resulting in the suppression of melanin synthesis. Moreover, the entry of Cpc into B16F10 cells was revealed by confocal immunofluorescence localization and immunoblot analysis. Conclusions Cpc exerted dual antimelanogenic mechanisms by upregulation of MAPK/ERK-dependent degradation of MITF and downregulation of p38 MAPK-regulated CREB activation to modulate melanin formation. Cpc may have potential applications in biomedicine, food, and cosmetic industries. PMID:21988805

A bio-inspired, active morphing skin for camber morphing structures

NASA Astrophysics Data System (ADS)

Feng, Ning; Liu, Liwu; Liu, Yanju; Leng, Jinson

2015-03-01

In this study, one kind of developed morphing skin embedded with pneumatic muscle fibers (PMFs) was manufactured and was employed for camber morphing structures. The output force and contraction of PMF as well as the morphing skin were experimentally characterized at a series of discrete actuator pressures varying from 0.15 to 0.35 MPa. The active morphing skin test results show that the output force is 73.59 N and the contraction is 0.097 (9.7%) at 0.35 MPa. Due to these properties, this active morphing skin could be easily used for the morphing structures. Then the proper airfoil profile was chosen to manufacture the adaptive airfoil in this study. The chord-wise bending airfoil structure was achieved by employing this kind of active morphing skin. Finally the deformed shapes of this chord-wise bending airfoil structure were obtained by 3-dimensions scanning measurement. Meanwhile the camber morphing structures were analyzed through the finite element method (FEM) and the deformed shapes of the upper surface skins were obtained. The experimental result and FEM analysis result of deformed shapes of the upper surface skins were compared in this paper.

Evolutionary relationships among sympatric life history forms of Dolly Varden inhabiting the landlocked Kronotsky Lake, Kamchatka, and a neighboring anadromous population

USGS Publications Warehouse

Ostberg, C.O.; Pavlov, S.D.; Hauser, L.

2009-01-01

We investigated the evolutionary relationships among five sympatric morphs of Dolly Varden Salvelinus malma (white, Schmidti, longhead, river, and dwarf) inhabiting landlocked Kronotsky Lake on the Kamchatka Peninsula, Russia, and an anadromous population below the barrier waterfall on the outflowing Kronotsky River. Morphological analyses indicated phenotypic differentiation corresponding to preferred habitat, the longhead (a limnetic piscivorous morph) having a fusiform body, long jaw, and short fins and the Schmidti (a benthic morph) having a robust body, small jaw, and long fins. Analysis of molecular variance among the Kronotsky Lake morphs indicated that contemporary gene flow is restricted both among morphs within locations and among locations within morphs. Gene flow from Kronotsky Lake into the anadromous population also appears to be restricted. Our findings indicate that there are two divergent evolutionary lineages, one consisting of the white, Schmidti, river, and dwarf morphs and the other of the longhead morph and the anadromous population, which suggests that Kronotsky Lake was subject to separate waves of immigration. The Kronotsky Lake Dolly Varden morphs may represent an example of ecological speciation in progress, and we present a working hypothesis for the diversification of morphs within Kronotsky Lake.

CPC_ACEENA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, Mei; Pekour, Mikhail

The condensation particle counter (CPC 3772 or 3010, TSI) measures the number concentration of aerosols from 10 nm to 3 microns. On the G1, it was operated using an external pump and maintained at 1 LPM using a critical orifice. CPC_CVI was installed after CVI inlet, and CVI inlet was operated between two modes: under-kinetic mode and CVI mode. CPC_Isok (3772) and CPC3025 were installed after iso-kinetic inlet and CPC_TD was after the thermal denuder (TD). The infomation about the TD can be found from FIMS dataset.

Acceleration of bone regeneration by activating Wnt/β-catenin signalling pathway via lithium released from lithium chloride/calcium phosphate cement in osteoporosis

NASA Astrophysics Data System (ADS)

Li, Li; Peng, Xiaozhong; Qin, Yongbao; Wang, Renchong; Tang, Jingli; Cui, Xu; Wang, Ting; Liu, Wenlong; Pan, Haobo; Li, Bing

2017-03-01

By virtue of its excellent bioactivity and osteoconductivity, calcium phosphate cement (CPC) has been applied extensively in bone engineering. Doping a trace element into CPC can change physical characteristics and enhance osteogenesis. The trace element lithium has been demonstrated to stimulate the proliferation and differentiation of osteoblasts. We investigated the fracture-healing effect of osteoporotic defects with lithium-doped calcium phosphate cement (Li/CPC) and the underlying mechanism. Li/CPC bodies immersed in simulated body fluid converted gradually to hydroxyapatite. Li/CPC extracts stimulated the proliferation and differentiation of osteoblasts upon release of lithium ions (Li+) at 25.35 ± 0.12 to 50.74 ± 0.13 mg/l through activation of the Wnt/β-catenin pathway in vitro. We also examined the effect of locally administered Li+ on defects in rat tibia between CPC and Li/CPC in vivo. Micro-computed tomography and histological staining showed that Li/CPC had better osteogenesis by increasing bone mass and promoting repair in defects compared with CPC (P < 0.05). Li/CPC also showed better osteoconductivity and osseointegration. These findings suggest that local release of Li+ from Li/CPC may accelerate bone regeneration from injury through activation of the Wnt/β-catenin pathway in osteoporosis.

Camouflage effects of various colour-marking morphs against different microhabitat backgrounds in a polymorphic pygmy grasshopper Tetrix japonica.

PubMed

Tsurui, Kaori; Honma, Atsushi; Nishida, Takayoshi

2010-07-06

Colour-marking polymorphism is widely distributed among cryptic species. To account for the adaptive significance of such polymorphisms, several hypotheses have been proposed to date. Although these hypotheses argue over the degree of camouflage effects of marking morphs (and the interactions between morphs and their microhabitat backgrounds), as far as we know, most empirical evidence has been provided under unnatural conditions (i.e., using artificial prey). Tetrix japonica, a pygmy grasshopper, is highly polymorphic in colour-markings and occurs in both sand and grass microhabitats. Even within a microhabitat, T. japonica is highly polymorphic. Using humans as dummy predators and printed photographs in which various morphs of grasshoppers were placed against different backgrounds, we addressed three questions to test the neutral, background heterogeneity, and differential crypsis hypotheses in four marking-type morphs: 1) do the morphs differ in the degree of crypsis in each microhabitat, 2) are different morphs most cryptic in specific backgrounds of the microhabitats, and 3) does the morph frequency reflect the degree of crypsis? The degree of camouflage differed among the four morphs; therefore, the neutral hypothesis was rejected. Furthermore, the order of camouflage advantage among morphs differed depending on the two types of backgrounds (sand and grass), although the grass background consistently provided greater camouflage effects. Thus, based on our results, we could not reject the background heterogeneity hypothesis. Under field conditions, the more cryptic morphs comprised a minority of the population. Overall, our results demonstrate that the different morphs were not equivalent in the degree of crypsis, but the degree of camouflage of the morphs was not consistent with the morph frequency. These findings suggest that trade-offs exist between the camouflage benefit of body colouration and other fitness components, providing a better understanding of the adaptive significance of colour-markings and presumably supporting the differential crypsis hypothesis.

Chromosomal passenger complex hydrodynamics suggests chaperoning of the inactive state by nucleoplasmin/nucleophosmin

PubMed Central

Hanley, Mariah L.; Yoo, Tae Yeon; Sonnett, Matthew; Needleman, Daniel J.; Mitchison, Timothy J.

2017-01-01

The chromosomal passenger complex (CPC) is a conserved, essential regulator of cell division. As such, significant anti–cancer drug development efforts have been focused on targeting it, most notably by inhibiting its AURKB kinase subunit. The CPC is activated by AURKB-catalyzed autophosphorylation on multiple subunits, but how this regulates CPC interactions with other mitotic proteins remains unclear. We investigated the hydrodynamic behavior of the CPC in Xenopus laevis egg cytosol using sucrose gradient sedimentation and in HeLa cells using fluorescence correlation spectroscopy. We found that autophosphorylation of the CPC decreases its sedimentation coefficient in egg cytosol and increases its diffusion coefficient in live cells, indicating a decrease in mass. Using immunoprecipitation coupled with mass spectrometry and immunoblots, we discovered that inactive, unphosphorylated CPC interacts with nucleophosmin/nucleoplasmin proteins, which are known to oligomerize into pentamers and decamers. Autophosphorylation of the CPC causes it to dissociate from nucleophosmin/nucleoplasmin. We propose that nucleophosmin/nucleoplasmin complexes serve as chaperones that negatively regulate the CPC and/or stabilize its inactive form, preventing CPC autophosphorylation and recruitment to chromatin and microtubules in mitosis. PMID:28404751

Infants prefer the faces of strangers or mothers to morphed faces: an uncanny valley between social novelty and familiarity.

PubMed

Matsuda, Yoshi-Taka; Okamoto, Yoko; Ida, Misako; Okanoya, Kazuo; Myowa-Yamakoshi, Masako

2012-10-23

The 'uncanny valley' response is a phenomenon involving the elicitation of a negative feeling and subsequent avoidant behaviour in human adults and infants as a result of viewing very realistic human-like robots or computer avatars. It is hypothesized that this uncanny feeling occurs because the realistic synthetic characters elicit the concept of 'human' but fail to satisfy it. Such violations of our normal expectations regarding social signals generate a feeling of unease. This conflict-induced uncanny valley between mutually exclusive categories (human and synthetic agent) raises a new question: could an uncanny feeling be elicited by other mutually exclusive categories, such as familiarity and novelty? Given that infants prefer both familiarity and novelty in social objects, we address this question as well as the associated developmental profile. Using the morphing technique and a preferential-looking paradigm, we demonstrated uncanny valley responses of infants to faces of mothers (i.e. familiarity) and strangers (i.e. novelty). Furthermore, this effect strengthened with the infant's age. We excluded the possibility that infants detect and avoid traces of morphing. This conclusion follows from our finding that the infants equally preferred strangers' faces and the morphed faces of two strangers. These results indicate that an uncanny valley between familiarity and novelty may accentuate the categorical perception of familiar and novel objects.

Differential foraging success across a light level spectrum explains the maintenance and spatial structure of colour morphs in a polymorphic bird.

PubMed

Tate, Gareth J; Bishop, Jacqueline M; Amar, Arjun

2016-06-01

Detectability of different colour morphs under varying light conditions has been proposed as an important driver in the maintenance of colour polymorphism via disruptive selection. To date, no studies have tested whether different morphs have selective advantages under differing light conditions. We tested this hypothesis in the black sparrowhawk, a polymorphic raptor exhibiting a discrete white and dark morph, and found that prey provisioning rates differ between the morphs depending on light condition. Dark morphs delivered more prey in lower light conditions, while white morphs provided more prey in brighter conditions. We found support for the role of breeding season light level in explaining the clinal pattern of variation in morph ratio across the species range throughout South Africa. Our results provide the first empirical evidence supporting the hypothesis that polymorphism in a species, and the spatial structuring of morphs across its distribution, may be driven by differential selective advantage via improved crypsis, under varying light conditions. © 2016 John Wiley & Sons Ltd/CNRS.

Morphing Wing Weight Predictors and Their Application in a Template-Based Morphing Aircraft Sizing Environment II. Part 2; Morphing Aircraft Sizing via Multi-level Optimization

NASA Technical Reports Server (NTRS)

Skillen, Michael D.; Crossley, William A.

2008-01-01

This report presents an approach for sizing of a morphing aircraft based upon a multi-level design optimization approach. For this effort, a morphing wing is one whose planform can make significant shape changes in flight - increasing wing area by 50% or more from the lowest possible area, changing sweep 30 or more, and/or increasing aspect ratio by as much as 200% from the lowest possible value. The top-level optimization problem seeks to minimize the gross weight of the aircraft by determining a set of "baseline" variables - these are common aircraft sizing variables, along with a set of "morphing limit" variables - these describe the maximum shape change for a particular morphing strategy. The sub-level optimization problems represent each segment in the morphing aircraft's design mission; here, each sub-level optimizer minimizes fuel consumed during each mission segment by changing the wing planform within the bounds set by the baseline and morphing limit variables from the top-level problem.

[Reconstruction of maxillary sinus superior wall fractures with calcium phosphate cement/recombinant human bonemorphogenetic protein 7 compound implanted material in rabbit].

PubMed

Zhang, Qunhui; Yu, Feng; Zhang, Haoliang; Gong, Huicheng; Lin, Ying

2015-11-01

To evaluate the osteogenetic character and repairing maxillary sinus superior wall fractures capability of calcium phosphate cement (CPC) before and after combined with recombinant human bone morphogenetie protein-7(rhBMP-7). A 10 mmX5 mm bone defect in the maxillary sinus superior wall was induced by surgery in all 24 New Zealand white rabbits. These 24 rabbits were randomly divided into two groups. The defects were repaired with CPC group (n = 12) and CPC/rhBMP-7 group (n = 12). The osteogenesis of bone defect was monitored by gro'ss observation, histological examination, observation under scanning electron microscope and measurement of ALP activity at 6 and 12 weeks after the implantation. In group CPC,new bone was found to form slowly and little by little. In group CPC/rhBMP-7, however, new bone was observed to form early and massively. The ALP activity in group CPC showed significant statistical difference with that of group CPC/rhBMP-7 (P < 0.05). The CPC/rhBMP-7 composite has osteoconductibility and osteoinductibility, comparing the use of CPC/rhBMP-7 with CPC for the repair of orbital fracture, the former show obvious advantage repairing ability in maxillary sinus superior wall defect.

Encapsulation of mesenchymal stem cells in chitosan/β-glycerophosphate hydrogel for seeding on a novel calcium phosphate cement scaffold.

PubMed

Liu, Tao; Li, Jian; Shao, Zengwu; Ma, Kaige; Zhang, Zhicai; Wang, Baichuan; Zhang, Yannan

2018-06-01

Due to its moldability, biocompatibility, osteoconductivity and resorbability, calcium phosphate cement (CPC) is a highly promising scaffold material for orthopedic applications. However, pH changes and ionic activity during the CPC setting reaction may adversely affect cells seeded directly on CPC. Moreover, a lack of macropores in CPC limits ingrowth of new bone. The objectives of this study were to prepare macroporous CPC scaffolds via porogen leaching, using mannitol crystals as the porogen and to evaluate the in vitro proliferation and osteogenic differentiation of mesenchymal stem cells (MSCs) encapsulated in chitosan/β-glycerophosphate (C/GP) hydrogel prior to exposure to the novel CPC scaffold. MSCs were found to be adhered to the surfaces of CPC macropores via scanning electron microscopy. The viability and osteogenic differentiation of MSCs in C/GP hydrogel with or without exposure to CPC constructs containing mannitol crystals indicated that coating with C/GP hydrogel protected the cells during cement mixing and setting. In conclusion, novel, macroporous CPC scaffolds were prepared, and our data indicate that a hydrogel encapsulation-based strategy can be used to protect cells during scaffold formation. Thus, the MSC-laden CPC scaffolds show promise for the delivery of stem cells to promote bone regeneration. Copyright © 2018 IPEM. Published by Elsevier Ltd. All rights reserved.

Performance of OMNIgene•SPUTUM (DNA Genotek) and cetylpyridinium chloride for sputum storage prior to mycobacterial culture.

PubMed

Affolabi, Dissou; Sanoussi, N'Dira; Sossou, Adelaide; Nys, Tom; Bodi, Ousman; Esse, Marius; Houeto, Sabine; Massou, Faridath; de Jong, Bouke C; Rigouts, Leen

2018-05-02

The aim was to assess the performance of both cetylpyridinium chloride (CPC) and OMNIgene•SPUTUM (OMNI) reagents for the maintenance of Mycobacterium tuberculosis viability in sputum prior to recovery by culture. Using 312 sputa, we evaluated the performance of the two reagents using culture on Löwenstein-Jensen medium after sputum storage in CPC or OMNI for up to 28 days. In addition, the viability of M. tuberculosis isolates stored in both reagents was assessed. The contamination rates for freshly processed samples and those stored in CPC were not statistically different, while the contamination rate for OMNI was significantly lower than that for fresh sputa (P=0.026 for 8 days and P=0.002 for 28 days of storage). The culture positivity for fresh sputa (81.7 %) was similar to that for samples stored in CPC, regardless of the storage time (89.8 % for CPC-8 and 73.0 % for CPC-28). For OMNI-preserved samples, the culture positivity was similar after 8 days of storage (84.2 %), but decreased significantly after 28 days (42.7 %; P<0.0001) compared to fresh sputa, CPC-8, CPC-28 and OMNI-8. There was a significant loss of viability for the H37Rv strain when it was stored in OMNI at room temperature beyond 8 days compared to CPC, but storage at 37 °C decreased recovery from both CPC- and OMNI-stored suspensions. Culture from sputum stored for 8 days at room temperature in OMNI or CPC gave comparable culture positivity rates to culture from fresh sputum, but after 28 days of storage the performance of OMNI decreased significantly compared to CPC.

Temporal and spatial distribution of Microcystis biomass and genotype in bloom areas of Lake Taihu.

PubMed

Guan, Dong-Xing; Wang, Xingyu; Xu, Huacheng; Chen, Li; Li, Pengfu; Ma, Lena Q

2018-06-26

Cyanobacterial blooms as a global environmental issue are of public health concern. In this study, we investigated the spatial (10 sites) and temporal (June, August and October) variations in: 1) their biomass based on chlorophyll-a (chl-a) concentration, 2) their toxic genotype based on gene copy ratio of mcyJ to cpcBA, and 3) their cpcBA genotype composition of Microcystis during cyanobacterial bloom in Lake Taihu. While spatial-temporal variations were found in chl-a and mcyJ/cpcBA ratio, only spatial variation was observed in cpcBA genotype composition. Samples from northwestern part had a higher chl-a, but mcyJ/cpcBA ratio didn't vary among the sites. High chl-a was observed in August, while mcyJ/cpcBA ratio and genotypic richness increased with time. The spatial variations in chl-a and mcyJ/cpcBA ratio and temporal variation in cpcBA genotype were correlated negatively with dissolved N and positively with dissolved P. Spatial distribution of Microcystis biomass was positively correlated with nitrite and P excluding October, but no correlation was found for spatial distribution of mcyJ/cpcBA ratio and cpcBA genotype. Spatial distribution of toxic and cpcBA genotypes may result from horizontal transport of Microcystis colonies, while spatial variation in Microcystis biomass was probably controlled by both nutrient-mediated growth and horizontal transport of Microcystis. The temporal variation in Microcystis biomass, toxic genotype and cpcBA genotype composition were related to nutrient levels, but cause-and-effect relationships require further study. Copyright © 2018 Elsevier Ltd. All rights reserved.

Water temperature, not fish morph, determines parasite infections of sympatric Icelandic threespine sticklebacks (Gasterosteus aculeatus).

PubMed

Karvonen, Anssi; Kristjánsson, Bjarni K; Skúlason, Skúli; Lanki, Maiju; Rellstab, Christian; Jokela, Jukka

2013-06-01

Parasite communities of fishes are known to respond directly to the abiotic environment of the host, for example, to water quality and water temperature. Biotic factors are also important as they affect the exposure profile through heterogeneities in parasite distribution in the environment. Parasites in a particular environment may pose a strong selection on fish. For example, ecological differences in selection by parasites have been hypothesized to facilitate evolutionary differentiation of freshwater fish morphs specializing on different food types. However, as parasites may also respond directly to abiotic environment the parasite risk does not depend only on biotic features of the host environment. It is possible that different morphs experience specific selection gradients by parasites but it is not clear how consistent the selection is when abiotic factors change. We examined parasite pressure in sympatric morphs of threespine stickleback (Gasterosteus aculeatus) across a temperature gradient in two large Icelandic lakes, Myvatn and Thingvallavatn. Habitat-specific temperature gradients in these lakes are opposite. Myvatn lava rock morph lives in a warm environment, while the mud morph lives in the cold. In Thingvallavatn, the lava rock morph lives in a cold environment and the mud morph in a warm habitat. We found more parasites in fish living in higher temperature in both lakes, independent of the fish morph, and this pattern was similar for the two dominating parasite taxa, trematodes and cestodes. However, at the same time, we also found higher parasite abundance in a third morph living in deep cold-water habitat in Thingvallavatn compared to the cold-water lava morph, indicating strong effect of habitat-specific biotic factors. Our results suggest complex interactions between water temperature and biotic factors in determining the parasite community structure, a pattern that may have implications for differentiation of stickleback morphs.

Enhancement of biodegradation and osseointegration of poly(ε-caprolactone)/calcium phosphate ceramic composite screws for osteofixation using calcium sulfate.

PubMed

Wu, Chang-Chin; Hsu, Li-Ho; Tsai, Yuh-Feng; Sumi, Shoichiro; Yang, Kai-Chiang

2016-04-04

Internal fixation devices, which can stabilize and realign fractured bone, are widely used in fracture management. In this paper, a biodegradable composite fixator, composed of poly(ε-caprolactone), calcium phosphate ceramic and calcium sulfate (PCL/CPC/CS), is developed. The composition of CS, which has a high dissolution rate, was expected to create a porous structure to improve osteofixation to the composite fixator. PCL, PCL/CPC, and PCL/CPC/CS samples were prepared and their physical properties were characterized in vitro. In vivo performance of the composite screws was verified in the distal femurs of rabbits. Results showed that the PCL/CPC/CS composite had a higher compressive strength (28.55 ± 3.32 MPa) in comparison with that of PCL (20.64 ± 1.81 MPa) (p < 0.05). A larger amount of apatite was formed on PCL/CPC/CS than on PCL/CPC, while no apatite was found on PCL after simulated body fluid immersion. In addition, PCL/CPC/CS composites also had a faster in vitro degradation rate (13.05 ± 3.42% in weight loss) relative to PCL (1.79 ± 0.23%) and PCL/CPC (4.32 ± 2.18%) (p < 0.001). In animal studies, PCL/CPC/CS screws showed a greater volume loss than that of PCL or PCL/CPC at 24 weeks post-implantation. Under micro-computerized tomography observation, animals with PCL/CPC/CS implants had better osseointegration in terms of the structural parameters of the distal metaphysis, including trabecular number, trabecular spacing, and connectivity density, than the PCL screw. This study reveals that the addition of CS accelerates the biodegradation and enhanced apatite formation of the PCL/CPC composite screw. This osteoconductive PCL/CPC/CS is a good candidate material for internal fixation devices.

Developing children’s palliative care in Africa through beacon centres: lessons learnt

PubMed Central

2013-01-01

Much progress has been made in the provision of palliative care across sub-Saharan Africa, however much still remains to be done, particularly in the area of children’s palliative care (CPC). The Beacon Centres programme was set up in 2009, aimed at improving access to CPC in South Africa, Uganda and Tanzania through more and better-trained health professionals and CPC clinical services of a high standard. Having identified sites in each country to develop into CPC Beacon Centres, Navigators were identified who would be the ‘champions’ for CPC in those sites and lead a programme of training, mentorship and support. Five navigators (2 in Uganda and Tanzania and 1 in South Africa) were trained between September and December 2009. Following this they undertook CPC needs assessments at the 3 centres and set up and delivered a six-month CPC training programme, providing mentorship and support to students to enable them to integrate CPC into their workplaces. To date, 188 participants have commenced the six-month course, with 80 having completed it. CPC has been integrated into the activities of the centres and a CPC virtual resource centre set up in South Africa. The achievements from the Beacon project have been great and the work of the navigators immense, but as in all projects it has not been without its challenges. Lessons learnt include issues around: the focus of the project; the length and nature of the training; assessment; accreditation; the choice of navigators; mentoring; administrative support; co-ordination; the choice of project sites; and the integration of CPC into services. The need for CPC is not going to go away and it is therefore important that models of scaling-up are found that are not only practical, feasible, affordable and sustainable, but that focus on the outcome of improved CPC for all those who need it. It is hoped that the lessons shared from the Beacon Project will help in developing and implementing such models. PMID:23419095

Gβ-Like CpcB Plays a Crucial Role for Growth and Development of Aspergillus nidulans and Aspergillus fumigatus

PubMed Central

Kong, Qing; Wang, Long; Liu, Zengran; Kwon, Nak-Jung; Kim, Sun Chang; Yu, Jae-Hyuk

2013-01-01

Growth, development, virulence and secondary metabolism in fungi are governed by heterotrimeric G proteins (G proteins). A Gβ-like protein called Gib2 has been shown to function as an atypical Gβ in Gpa1-cAMP signaling in Cryptococcus neoformans. We found that the previously reported CpcB (cross pathway control B) protein is the ortholog of Gib2 in Aspergillus nidulans and Aspergillus fumigatus. In this report, we further characterize the roles of CpcB in governing growth, development and toxigenesis in the two aspergilli. The deletion of cpcB results in severely impaired cellular growth, delayed spore germination, and defective asexual sporulation (conidiation) in both aspergilli. Moreover, CpcB is necessary for proper expression of the key developmental activator brlA during initiation and progression of conidiation in A. nidulans and A. fumigatus. Somewhat in accordance with the previous study, the absence of cpcB results in the formation of fewer, but not micro-, cleistothecia in A. nidulans in the presence of wild type veA, an essential activator of sexual development. However, the cpcB deletion mutant cleistothecia contain no ascospores, validating that CpcB is required for progression and completion of sexual fruiting including ascosporogenesis. Furthermore, unlike the canonical GβSfaD, CpcB is not needed for the biosynthesis of the mycotoxin sterigmatocystin (ST) as the cpcB null mutant produced reduced amount of ST with unaltered STC gene expression. However, in A. fumigatus, the deletion of cpcB results in the blockage of gliotoxin (GT) production. Further genetic analyses in A. nidulans indicate that CpcB may play a central role in vegetative growth, which might be independent of FadA- and GanB-mediated signaling. A speculative model summarizing the roles of CpcB in conjunction with SfaD in A. nidulans is presented. PMID:23936193

Gβ-like CpcB plays a crucial role for growth and development of Aspergillus nidulans and Aspergillus fumigatus.

PubMed

Kong, Qing; Wang, Long; Liu, Zengran; Kwon, Nak-Jung; Kim, Sun Chang; Yu, Jae-Hyuk

2013-01-01

Growth, development, virulence and secondary metabolism in fungi are governed by heterotrimeric G proteins (G proteins). A Gβ-like protein called Gib2 has been shown to function as an atypical Gβ in Gpa1-cAMP signaling in Cryptococcus neoformans. We found that the previously reported CpcB (cross pathway control B) protein is the ortholog of Gib2 in Aspergillus nidulans and Aspergillus fumigatus. In this report, we further characterize the roles of CpcB in governing growth, development and toxigenesis in the two aspergilli. The deletion of cpcB results in severely impaired cellular growth, delayed spore germination, and defective asexual sporulation (conidiation) in both aspergilli. Moreover, CpcB is necessary for proper expression of the key developmental activator brlA during initiation and progression of conidiation in A. nidulans and A. fumigatus. Somewhat in accordance with the previous study, the absence of cpcB results in the formation of fewer, but not micro-, cleistothecia in A. nidulans in the presence of wild type veA, an essential activator of sexual development. However, the cpcB deletion mutant cleistothecia contain no ascospores, validating that CpcB is required for progression and completion of sexual fruiting including ascosporogenesis. Furthermore, unlike the canonical GβSfaD, CpcB is not needed for the biosynthesis of the mycotoxin sterigmatocystin (ST) as the cpcB null mutant produced reduced amount of ST with unaltered STC gene expression. However, in A. fumigatus, the deletion of cpcB results in the blockage of gliotoxin (GT) production. Further genetic analyses in A. nidulans indicate that CpcB may play a central role in vegetative growth, which might be independent of FadA- and GanB-mediated signaling. A speculative model summarizing the roles of CpcB in conjunction with SfaD in A. nidulans is presented.

Floral variation and environmental heterogeneity in a tristylous clonal aquatic of the Pantanal wetlands of Brazil

PubMed Central

Leme da Cunha, Nicolay; Fischer, Erich; Lorenz-Lemke, Aline P.; Barrett, Spencer C. H.

2014-01-01

Background and Aims The balance between stochastic forces and frequency-dependent mating largely governs style morph frequencies in heterostylous populations. In clonal species, deviations from equal morph ratios often result from founder events and unfavourable conditions for sexual reproduction. The aim of this study was to investigate whether different flooding regimes, because of their influence on sexual vs. clonal reproduction, are associated with regional variation in morph frequencies and floral trait differentiation in populations of the clonal, tristylous, aquatic Eichhornia azurea (Pontederiaceae) in the Pantanal wetlands of Brazil. Methods Style morph frequencies were sampled from 73 populations distributed across four flooding regimes differing in depth and duration. Measurements of flower size, sex-organ dimension, pollen size and pollen production were made in selected populations, and pollinator assemblages and their functional traits were recorded. Key Results Most populations of E. azurea were tristylous (78 %), but the majority exhibited uneven morph ratios. The frequency of the mid-styled morph was significantly lower than that of the long- and short-styled morphs. Morph evenness was positively associated with population size but not with flooding regime. There were significant phenotypic differences among flooding regimes for all floral traits, including populations with reduced flower size, sex-organ length and smaller pollen. Pollinator assemblages varied with flood duration. Conclusions The similar morph structure and evenness of populations, regardless of flooding regime, suggest that sexual reproduction and clonal dispersal are sufficiently common to prevent the signature of founder events from dominating in a region. However, the pervasive occurrence of biased morph ratios in most populations suggests that many are in a non-equilibrium state. The reduced frequency of the mid-styled morph in trimorphic and dimorphic populations may be associated with the weak self-incompatibility of this morph resulting in selfing and inbreeding depression. Clonality in E. azurea and the weak self-incompatibility of the mid-styled morph may make it more vulnerable to geitonogamous selfing. PMID:25180289

Flutter suppression and stability analysis for a variable-span wing via morphing technology

NASA Astrophysics Data System (ADS)

Li, Wencheng; Jin, Dongping

2018-01-01

A morphing wing can enhance aerodynamic characteristics and control authority as an alternative to using ailerons. To use morphing technology for flutter suppression, the dynamical behavior and stability of a variable-span wing subjected to the supersonic aerodynamic loads are investigated numerically in this paper. An axially moving cantilever plate is employed to model the variable-span wing, in which the governing equations of motion are established via the Kane method and piston theory. A morphing strategy based on axially moving rates is proposed to suppress the flutter that occurs beyond the critical span length, and the flutter stability is verified by Floquet theory. Furthermore, the transient stability during the morphing motion is analyzed and the upper bound of the morphing rate is obtained. The simulation results indicate that the proposed morphing law, which is varying periodically with a proper amplitude, could accomplish the flutter suppression. Further, the upper bound of the morphing speed decreases rapidly once the span length is close to its critical span length.

Cryptic dioecy in Mussaenda pubescens (Rubiaceae): a species with stigma-height dimorphism.

PubMed

Li, Ai-Min; Wu, Xiao-Qin; Zhang, Dian-Xiang; Barrett, Spencer C H

2010-10-01

Evolutionary transitions from heterostyly to dioecy have been proposed in several angiosperm families, particularly in Rubiaceae. These transitions involve the spread of male and female sterility mutations resulting in modifications to the gender of ancestral hermaphrodites. Despite sustained interest in the gender strategies of plants, the structural and developmental bases for transitions in sexual systems are poorly understood. Here, floral morphology, patterns of fertility, pollen-tube growth and floral development are investigated in two populations of the scandent shrub Mussaenda pubescens (Rubiaceae), native to southern China, by means of experimental and open-pollinations, light microscopy, fluorescence microscopy and scanning electron microscopy combined with paraffin sectioning. Mussaenda pubescens has perfect (hermaphroditic) flowers and populations with two style-length morphs but only weak differentiation in anther position (stigma-height dimorphism). Experimental pollinations demonstrated that despite morphological hermaphroditism, the species is functionally dioecious. The long-styled (L) morph possesses sterile pollen and functions as a female, whereas the short-styled (S) morph is female sterile and functions as a male. Self- and intra-morph pollinations of the S-morph were consistent with those expected from dimorphic incompatibility. The two populations investigated were both S-morph (male) biased. Investigations of early stages of floral development indicated patterns typical of hermaphroditic flowers, with no significant differences in organ growth between the floral morphs. Meiosis of microspore mother cells was of the simultaneous type with tetrads isobilateral in shape. The tapetal cells in anther walls of the L-morph became vacuolized during meiosis I, ahead of the uninucleate microspore stage in the S-morph. In the L-morph, the microspore nucleus degenerated at the tetrad stage resulting in male sterility. Microsporogenesis and male gametophyte development was normal in the S-morph. Failure in the formation of megaspore mother cells and/or the development of megagametophytes resulted in female sterility in the S-morph, compared with normal megasporogenesis in the L-morph. In M. pubescens, cryptic dioecy has evolved from stigma-height dimorphism as a result of morph-specific sterility mutations.

Skylight: a hollow prismatic CPC

NASA Astrophysics Data System (ADS)

Fernandez-Balbuena, Antonio Alvarez; Vázquez-Moliní, Daniel; Garcia-Fernandez, Berta; Garcia-Botella, Angel; Bernabeu, Eusebio

2009-08-01

Many applications involve the use of a compound parabolic concentrator (CPC) like, natural lighting, thermal applications, optics for illuminators, optical fibre coupling and solar energy. The use of a CPC in reverse mode for natural lighting gives the chance to use it as a lighting skylight in ceilings because light output is controlled inside the design angle, on the contrary having a low flux transfer ratio because of the reduced area of the entrance pupil regarding exit pupil. The authors propose an innovative 3D hollow prismatic CPC (HPCPC) made of a dielectric material, which has a high efficiency comparing it with aluminium CPC. The basic idea is to use a hollow prismatic light guide with CPC shape. This paper reports 2D, 3D design and numerical analysis by raytracing software, also experimental results are shown. The system works almost like a true CPC when light enters through standard entrance pupil and also collect light that enters outside entrance pupil. Performance and efficiency of the prismatic CPC is in average 300% higher than standard aluminium CPC for collimated light in a range from 0º to 85º. A prototype has been developed and tested.

Study of the electrical and thermal performances of photovoltaic thermal collector-compound parabolic concentrated

NASA Astrophysics Data System (ADS)

Jaaz, Ahed Hameed; Sopian, Kamaruzzaman; Gaaz, Tayser Sumer

2018-06-01

The importance of utilizing the solar energy as a very suitable source among multi-source approaches to replace the conventional energy is on the rise in the last four decades. The invention of the photovoltaic module (PV) could be the corner stone in this process. However, the limited amount of energy obtained from PV was and still the main challenge of full utilization of the solar energy. In this paper, the use of the compound parabolic concentrator (CPC) along with the thermal photovoltaic module (PVT) where the cooling process of the CPC is conducted using a novel technique of water jet impingement has applied experimentally and physically tested. The test includes the effect of water jet impingement on the total power, electrical efficiency, thermal efficiency, and total efficiency on CPC-PVT system. The cooling process at the maximum irradiation by water jet impingement resulted in improving the electrical efficiency by 7%, total output power by 31% and the thermal efficiency by 81%. These results outperform the recent highest results recorded by the most recent work.

Adaptive building skin structures

NASA Astrophysics Data System (ADS)

Del Grosso, A. E.; Basso, P.

2010-12-01

The concept of adaptive and morphing structures has gained considerable attention in the recent years in many fields of engineering. In civil engineering very few practical applications are reported to date however. Non-conventional structural concepts like deployable, inflatable and morphing structures may indeed provide innovative solutions to some of the problems that the construction industry is being called to face. To give some examples, searches for low-energy consumption or even energy-harvesting green buildings are amongst such problems. This paper first presents a review of the above problems and technologies, which shows how the solution to these problems requires a multidisciplinary approach, involving the integration of architectural and engineering disciplines. The discussion continues with the presentation of a possible application of two adaptive and dynamically morphing structures which are proposed for the realization of an acoustic envelope. The core of the two applications is the use of a novel optimization process which leads the search for optimal solutions by means of an evolutionary technique while the compatibility of the resulting configurations of the adaptive envelope is ensured by the virtual force density method.

SMA actuators for morphing wings

NASA Astrophysics Data System (ADS)

Brailovski, V.; Terriault, P.; Georges, T.; Coutu, D.

An experimental morphing laminar wing was developed to prove the feasibility of aircraft fuel consumption reduction through enhancement of the laminar flow regime over the wing extrados. The morphing wing prototype designed for subsonic cruise flight conditions (Mach 0.2 … 0.3; angle of attack - 1 … +2∘), combines three principal subsystems: (1) flexible extrados, (2) rigid intrados and (3) an actuator group located inside the wing box. The morphing capability of the wing relies on controlled deformation of the wing extrados under the action of shape memory alloys (SMA) actuators. A coupled fluid-structure model of the morphing wing was used to evaluate its mechanical and aerodynamic performances in different flight conditions. A 0.5 m chord and 1 m span prototype of the morphing wing was tested in a subsonic wind tunnel. In this work, SMA actuators for morphing wings were modeled using a coupled thermo-mechanical finite element model and they were windtunnel validated. If the thermo-mechanical model of SMA actuators presented in this work is coupled with the previously developed structureaerodynamic model of the morphing wing, it could serve for the optimization of the entire morphing wing system.

Lipogenesis in a wing-polymorphic cricket: Canalization versus morph-specific plasticity as a function of nutritional heterogeneity.

PubMed

Zera, Anthony J; Clark, Rebecca; Behmer, Spence

2016-12-01

The influence of variable nutritional input on life history adaptation is a central, but incompletely understood aspect of life history physiology. The wing-polymorphic cricket, Gryllus firmus, has been extensively studied with respect to the biochemical basis of life history adaptation, in particular, modification of lipid metabolism that underlies the enhanced accumulation of lipid flight fuel in the dispersing morph [LW(f)=long wings with functional flight muscles] relative to the flightless (SW=short-winged) morph. To date, biochemical studies have been undertaken almost exclusively using a single laboratory diet. Thus, the extent to which nutritional heterogeneity, likely experienced in the field, influences this key morph adaptation is unknown. We used the experimental approach of the Geometric Framework for Nutrition and employed 13 diets that differed in the amounts and ratios of protein and carbohydrate to assess how nutrient amount and balance affects morph-specific lipid biosynthesis. Greater lipid biosynthesis and allocation to the soma in the LW(f) compared with the SW morph (1) occurred across the entire protein-carbohydrate landscape and (2) is likely an important contributor to elevated somatic lipid in the LW(f) morph across the entire protein-carbohydrate landscape. Nevertheless, dietary carbohydrate strongly affected lipid biosynthesis in a morph-specific manner (to a greater degree in the LW(f) morph). Lipogenesis in the SW morph may be constrained due to its more limited lipid storage capacity compared to the LW(f) morph. Elevated activity of NADP + -isocitrate dehydrogenase (NADP + -IDH), an enzyme that produces reducing equivalents for lipid biosynthesis, was correlated with and may be an important cause of the increased lipogenesis in the LW(f) morph across most, but not all regions of the protein-carbohydrate landscape. By contrast, ATP-citrate lyase (ACL), an enzyme that catalyzes the first step in the pathway of fatty acid biosynthesis, showed complex morph-specific patterns of activity that were strongly contingent upon diet. Morph-specific patterns of NADP + -IDH and ACL activities across the nutrient landscape were much more complex than expected from previous studies on a single diet. Collectively, our results indicate that the biochemical basis of an important life history adaptation, morph-specific lipogenesis, can be canalized in the face of substantial nutritional heterogeneity. However, in some regions of the protein-carbohydrate landscape, it is strongly modulated in a morph-specific manner. Copyright © 2016 Elsevier Ltd. All rights reserved.

Outdoor Performance Analysis of a Photovoltaic Thermal (PVT) Collector with Jet Impingement and Compound Parabolic Concentrator (CPC)

PubMed Central

Jaaz, Ahed Hameed; Hasan, Husam Abdulrasool; Sopian, Kamaruzzaman; Kadhum, Abdul Amir H.; Gaaz, Tayser Sumer

2017-01-01

This paper discusses the effect of jet impingement of water on a photovoltaic thermal (PVT) collector and compound parabolic concentrators (CPC) on electrical efficiency, thermal efficiency and power production of a PVT system. A prototype of a PVT solar water collector installed with a jet impingement and CPC has been designed, fabricated and experimentally investigated. The efficiency of the system can be improved by using jet impingement of water to decrease the temperature of the solar cells. The electrical efficiency and power output are directly correlated with the mass flow rate. The results show that electrical efficiency was improved by 7% when using CPC and jet impingement cooling in a PVT solar collector at 1:00 p.m. (solar irradiance of 1050 W/m2 and an ambient temperature of 33.5 °C). It can also be seen that the power output improved by 36% when using jet impingement cooling with CPC, and 20% without CPC in the photovoltaic (PV) module at 1:30 p.m. The short-circuit current ISC of the PV module experienced an improvement of ~28% when using jet impingement cooling with CPC, and 11.7% without CPC. The output of the PV module was enhanced by 31% when using jet impingement cooling with CPC, and 16% without CPC. PMID:28763048

Outdoor Performance Analysis of a Photovoltaic Thermal (PVT) Collector with Jet Impingement and Compound Parabolic Concentrator (CPC).

PubMed

Jaaz, Ahed Hameed; Hasan, Husam Abdulrasool; Sopian, Kamaruzzaman; Kadhum, Abdul Amir H; Gaaz, Tayser Sumer; Al-Amiery, Ahmed A

2017-08-01

This paper discusses the effect of jet impingement of water on a photovoltaic thermal (PVT) collector and compound parabolic concentrators (CPC) on electrical efficiency, thermal efficiency and power production of a PVT system. A prototype of a PVT solar water collector installed with a jet impingement and CPC has been designed, fabricated and experimentally investigated. The efficiency of the system can be improved by using jet impingement of water to decrease the temperature of the solar cells. The electrical efficiency and power output are directly correlated with the mass flow rate. The results show that electrical efficiency was improved by 7% when using CPC and jet impingement cooling in a PVT solar collector at 1:00 p.m. (solar irradiance of 1050 W/m² and an ambient temperature of 33.5 °C). It can also be seen that the power output improved by 36% when using jet impingement cooling with CPC, and 20% without CPC in the photovoltaic (PV) module at 1:30 p.m. The short-circuit current I SC of the PV module experienced an improvement of ~28% when using jet impingement cooling with CPC, and 11.7% without CPC. The output of the PV module was enhanced by 31% when using jet impingement cooling with CPC, and 16% without CPC.

Developmental decoupling of alternative phenotypes: insights from the transcriptomes of horn-polyphenic beetles

PubMed Central

Snell-Rood, Emilie C.; Cash, Amy; Han, Mira V.; Kijimoto, Teiya; Andrews, Justen; Moczek, Armin P.

2010-01-01

Developmental mechanisms play an important role in determining the costs, limits, and evolutionary consequences of phenotypic plasticity. One issue central to these claims is the hypothesis of developmental decoupling, where alternate morphs result from evolutionarily independent developmental pathways. We address this assumption through a microarray study that tests whether differences in gene expression between alternate morphs are as divergent as those between sexes, a classic example of developmental decoupling. We then examine whether genes with morph-biased expression are less conserved than genes with shared expression between morphs, as predicted if developmental decoupling relaxes pleiotropic constraints on divergence. We focus on the developing horns and brains of two species of horned beetles with spectacular sexual- and morph-dimorphism in the expression of horns and fighting behavior. We find that patterns of gene expression were as divergent between morphs as they were between sexes. However, overall patterns of gene expression were also highly correlated across morphs and sexes. Morph-biased genes were more evolutionarily divergent, suggesting a role of relaxed pleiotropic constraints or relaxed selection. Together these results suggest that alternate morphs are to some extent developmentally decoupled, and that this decoupling has significant evolutionary consequences. However, alternative morphs may not be as developmentally decoupled as sometimes assumed and such hypotheses of development should be revisited and refined. PMID:20731717

Cardiac progenitor-derived exosomes protect ischemic myocardium from acute ischemia/reperfusion injury

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Lijuan; Cardiovascular Disease, Internal Medicine, University of Cincinnati, 231 Albert Sabin Way, Cincinnati, OH 45267; Wang, Yingjie

Highlights: ► Cardiac progenitor-derived (CPC) Exosomes protect H9C2 from apoptosis in vitro. ► CPC-exosomes protect cardiomyoyctes from MI/R induced apoptosis in vivo. ► CPC-exosomes were taken up by H9C2 with high efficiency using PKH26 labeling. ► miR-451, one of GATA4-responsive miRNA cluster, is enriched in CPC-exosomes. -- Abstract: Background: Cardiac progenitors (CPC) mediate cardioprotection via paracrine effects. To date, most of studies focused on secreted paracrine proteins. Here we investigated the CPC-derived-exosomes on protecting myocardium from acute ischemia/reperfusion (MI/R) injury. Methods and results: CPC were isolated from mouse heart using two-step protocol. Exosomes were purified from conditional medium, and confirmedmore » by electron micrograph and Western blot using CD63 as a marker. qRT-PCR shows that CPC-exosomes have high level expression of GATA4-responsive-miR-451. Exosomes were ex vivo labeled with PKH26, We observed exosomes can be uptaken by H9C2 cardiomyoblasts with high efficiency after 12 h incubation. CPC-exosomes protect H9C2 from oxidative stress by inhibiting caspase 3/7 activation invitro. In vivo delivery of CPC-exosomes in an acute mouse myocardial ischemia/reperfusion model inhibited cardiomyocyte apoptosis by about 53% in comparison with PBS control (p < 0.05). Conclusion: Our results suggest, for the first time, the CPC-exosomes can be used as a therapeutic vehicle for cardioprotection, and highlights a new perspective for using non-cell exosomes for cardiac disease.« less

Basic properties of calcium phosphate cement containing atelocollagen in its liquid or powder phases.

PubMed

Miyamoto, Y; Ishikawa, K; Takechi, M; Toh, T; Yuasa, T; Nagayama, M; Suzuki, K

1998-01-01

The basic properties of calcium phosphate cement (CPC) containing atelocollagen, the main component of the organic substrate in bone, were studied in an initial evaluation for the fabrication of modified CPC. The setting time of conventional CPC (c-CPC) was prolonged to over 100 min when c-CPC contained 1% or more atelocollagen. The diametral tensile strength (DTS) of c-CPC decreased linearly with the collagen content, descending to below the detection limit when the c-CPC contained 3% or more atelocollagen. Therefore, use of c-CPC as the base cement seems inappropriate for the fabrication of atelocollagen-containing CPC. In contrast, the cement set at 9-34 min when fast-setting CPC (FSCPC) was used as the base cement and contained 1-5% atelocollagen, respectively. Although addition of atelocollagen resulted in the decrease of DTS of the set mass, the DTS was approximately the same, 6-8 MPa, at contents of atelocollagen between 1% and 5%. When atelocollagen was added to FSCPC, the handling property was improved significantly. The paste also became more adhesive with increase in atelocollagen content. These properties are desirable for its use in surgical procedures since, for example, bony defects can be filled easily and without a space interposed between the bone and cement paste. Although there are some disadvantages for the addition of atelocollagen to CPC, it can be accepted as long as FSCPC was used as the base cement. We conclude that further evaluations of the effects of atelocollagen, such as biocompatibility, bone synthesis, and bone replacement behaviour should be done, using FSCPC as the base cement.

If Arctic charr Salvelinus alpinus is “the most diverse vertebrate,” what is the lake charr Salvelinus namaycush?

USGS Publications Warehouse

Muir, Andrew M.; Hansen, Michael J.; Bronte, Charles R.; Krueger, Charles C.

2016-01-01

Teleost fishes are prominent vertebrate models of evolution, illustrated among old-world radiations by the Cichlidae of East African Great Lakes and new-world radiations by the circumpolar Arctic charr Salvelinus alpinus. Herein, we describe variation in lake charr S. namaycush morphology, life history, physiology, and ecology, as another example of radiation. The lake charr is restricted to northern North America, where it originated from glacial refugia and diversified in large lakes. Shallow and deepwater morphs arose in multiple lakes, with a large-bodied shallow-water ‘lean’ morph in shallow inshore depths, a small-bodied mid-water ‘humper’ morph on offshore shoals or banks, and a large-bodied deep-water ‘siscowet’ morph at depths > 100 m. Eye position, gape size, and gillraker length and spacing adapted for feeding on different-sized prey, with piscivorous morphs (leans and siscowets) reaching larger asymptotic size than invertivorous morphs (humpers). Lean morphs are light in color, whereas deepwater morphs are drab and dark, although the pattern is reversed in dark tannic lakes. Morphs shift from benthic to pelagic feeding at a length of 400–490-mm. Phenotypic differences in locomotion, buoyancy, and lipid metabolism evolved into different mechanisms for buoyancy regulation, with lean morphs relying on hydrodynamic lift and siscowet morphs relying on hydrostatic lift. We suggest that the Salvelinus genus, rather than the species S. alpinus, is a diverse genus that should be the subject of comparative studies of processes causing divergence and adaptation among member species that may lead to a more complete evolutionary conceptual model.

Pollinator Competition as a Driver of Floral Divergence: An Experimental Test.

PubMed

Temeles, Ethan J; Newman, Julia T; Newman, Jennifer H; Cho, Se Yeon; Mazzotta, Alexandra R; Kress, W John

2016-01-01

Optimal foraging models of floral divergence predict that competition between two different types of pollinators will result in partitioning, increased assortative mating, and divergence of two floral phenotypes. We tested these predictions in a tropical plant-pollinator system using sexes of purple-throated carib hummingbirds (Anthracothorax jugularis) as the pollinators, red and yellow inflorescence morphs of Heliconia caribaea as the plants, and fluorescent dyes as pollen analogs in an enclosed outdoor garden. When foraging alone, males exhibited a significant preference for the yellow morph of H. caribaea, whereas females exhibited no preference. In competition, males maintained their preference for the yellow morph and through aggression caused females to over-visit the red morph, resulting in resource partitioning. Competition significantly increased within-morph dye transfer (assortative mating) relative to non-competitive environments. Competition and partitioning of color morphs by sexes of purple-throated caribs also resulted in selection for floral divergence as measured by dye deposition on stigmas. Red and yellow morphs did not differ significantly in dye deposition in the competition trials, but differences in dye deposition and preferences for morphs when sexes of purple-throated caribs foraged alone implied fixation of one or the other color morph in the absence of competition. Competition also resulted in selection for divergence in corolla length, with the red morph experiencing directional selection for longer corollas and the yellow morph experiencing stabilizing selection on corolla length. Our results thus support predictions of foraging models of floral divergence and indicate that pollinator competition is a viable mechanism for divergence in floral traits of plants.

Pollinator Competition as a Driver of Floral Divergence: An Experimental Test

PubMed Central

Temeles, Ethan J.; Newman, Julia T.; Newman, Jennifer H.; Cho, Se Yeon; Mazzotta, Alexandra R.; Kress, W. John

2016-01-01

Optimal foraging models of floral divergence predict that competition between two different types of pollinators will result in partitioning, increased assortative mating, and divergence of two floral phenotypes. We tested these predictions in a tropical plant-pollinator system using sexes of purple-throated carib hummingbirds (Anthracothorax jugularis) as the pollinators, red and yellow inflorescence morphs of Heliconia caribaea as the plants, and fluorescent dyes as pollen analogs in an enclosed outdoor garden. When foraging alone, males exhibited a significant preference for the yellow morph of H. caribaea, whereas females exhibited no preference. In competition, males maintained their preference for the yellow morph and through aggression caused females to over-visit the red morph, resulting in resource partitioning. Competition significantly increased within-morph dye transfer (assortative mating) relative to non-competitive environments. Competition and partitioning of color morphs by sexes of purple-throated caribs also resulted in selection for floral divergence as measured by dye deposition on stigmas. Red and yellow morphs did not differ significantly in dye deposition in the competition trials, but differences in dye deposition and preferences for morphs when sexes of purple-throated caribs foraged alone implied fixation of one or the other color morph in the absence of competition. Competition also resulted in selection for divergence in corolla length, with the red morph experiencing directional selection for longer corollas and the yellow morph experiencing stabilizing selection on corolla length. Our results thus support predictions of foraging models of floral divergence and indicate that pollinator competition is a viable mechanism for divergence in floral traits of plants. PMID:26814810

Development of Collaborative Research Initiatives to Advance the Aerospace Sciences-via the Communications, Electronics, Information Systems Focus Group

NASA Technical Reports Server (NTRS)

Knasel, T. Michael

1996-01-01

The primary goal of the Adaptive Vision Laboratory Research project was to develop advanced computer vision systems for automatic target recognition. The approach used in this effort combined several machine learning paradigms including evolutionary learning algorithms, neural networks, and adaptive clustering techniques to develop the E-MOR.PH system. This system is capable of generating pattern recognition systems to solve a wide variety of complex recognition tasks. A series of simulation experiments were conducted using E-MORPH to solve problems in OCR, military target recognition, industrial inspection, and medical image analysis. The bulk of the funds provided through this grant were used to purchase computer hardware and software to support these computationally intensive simulations. The payoff from this effort is the reduced need for human involvement in the design and implementation of recognition systems. We have shown that the techniques used in E-MORPH are generic and readily transition to other problem domains. Specifically, E-MORPH is multi-phase evolutionary leaming system that evolves cooperative sets of features detectors and combines their response using an adaptive classifier to form a complete pattern recognition system. The system can operate on binary or grayscale images. In our most recent experiments, we used multi-resolution images that are formed by applying a Gabor wavelet transform to a set of grayscale input images. To begin the leaming process, candidate chips are extracted from the multi-resolution images to form a training set and a test set. A population of detector sets is randomly initialized to start the evolutionary process. Using a combination of evolutionary programming and genetic algorithms, the feature detectors are enhanced to solve a recognition problem. The design of E-MORPH and recognition results for a complex problem in medical image analysis are described at the end of this report. The specific task involves the identification of vertebrae in x-ray images of human spinal columns. This problem is extremely challenging because the individual vertebra exhibit variation in shape, scale, orientation, and contrast. E-MORPH generated several accurate recognition systems to solve this task. This dual use of this ATR technology clearly demonstrates the flexibility and power of our approach.

A Histopathological Comparison of Pulpal Response to Chitra-CPC and Formocresol used as Pulpotomy Agents in Primary Teeth: A Clinical Trial

PubMed Central

Thomas, Bijimol

2012-01-01

ABSTRACT Preventive measures have helped to minimize the occurrence of dental caries. However, premature loss of primary teeth on account of dental caries still remains a common problem among children. The pulpotomy technique has been the choice for treating vital primary and young permanent teeth with carious, mechanical and traumatic pulp exposures. The ideal pulpotomy medicament should be bioinductive or at least biocompatible, bactericidal and harmless to the pulp and surrounding structures. It should also promote healing of the radicular pulp and prevent bacterial microleakage with the least interference in the physiological process of root resorption. Since the best criteria for judging the effectiveness of a medicament when used for vital pulp therapy is the response that it produces in the pulp. The purpose of the present study was to evaluate and compare the response of human pulp tissue to recently developed Indian material, Sree Chitra-Calcium Phosphate Cement (Chitra-CPC) and formocresol, used as pulpotomy agent in deciduous teeth. Chitra-CPC has been compared with formocresol, taking into account that formocresol is still considered the gold standard in primary tooth pulpotomy. The study was conducted among 10 children in the age group of 8 to 12 years focusing on 20 noncarious primary canines indicated for serial extraction. Each patient received two different pulpotomy procedures—one in each of the primary canines using formocresol and the other with Chitra-CPC as pulpotomy agents. After 70 days, the teeth were extracted and subjected to histological examination. The results did not reveal statistically significant difference between the two groups. But Chitra-CPC gave more favorable results, in respect of pulpal inflammation, dentin bridge formation, quality of dentin bridge and connective tissue in dentin bridge. How to cite this article: Ratnakumari N, Thomas B. A Histopathological Comparison of Pulpal Response to Chitra- CPC and Formocresol used as Pulpotomy Agents in Primary Teeth: A Clinical Trial. Int J Clin Pediatr Dent 2012;5(1):6-13. PMID:25206127

Improvement of physical properties of calcium phosphate cement by elastin-like polypeptide supplementation.

PubMed

Jang, Ji-Hyun; Shin, Sumi; Kim, Hyun-Jung; Jeong, Jinyoung; Jin, Hyo-Eon; Desai, Malav S; Lee, Seung-Wuk; Kim, Sun-Young

2018-03-26

Calcium phosphate cements (CPCs) are synthetic bioactive cements widely used as hard tissue substitutes. Critical limitations of use include their poor mechanical properties and poor anti-washout behaviour. To address those limitations, we combined CPC with genetically engineered elastin-like polypeptides (ELPs). We investigated the effect of the ELPs on the physical properties and biocompatibility of CPC by testing ELP/CPC composites with various liquid/powder ratios. Our results show that the addition of ELPs improved the mechanical properties of the CPC, including the microhardness, compressive strength, and washout resistance. The biocompatibility of ELP/CPC composites was also comparable to that of the CPC alone. However, supplementing CPC with ELPs functionalized with octaglutamate as a hydroxyapatite binding peptide increased the setting time of the cement. With further design and modification of our biomolecules and composites, our research will lead to products with diverse applications in biology and medicine.

Finite Element Analysis of Morphing Piezoelectric Structures Studied

NASA Technical Reports Server (NTRS)

Lee, Ho-Jun

2002-01-01

The development of morphing aerospace structures that optimize their shape offers the potential to significantly improve the performance of existing airplanes. These morphing vehicles will operate with new capabilities to reduce noise, damp vibrations, manipulate flow, and monitor damage. Piezoelectric materials represent one of the popular materials currently being investigated for applications in morphing structures.

Cannibalistic-morph Tiger Salamanders in unexpected ecological contexts

USGS Publications Warehouse

McLean, Kyle I.; Stockwell, Craig A.; Mushet, David M.

2016-01-01

Barred tiger salamanders [Ambystoma mavortium (Baird, 1850)] exhibit two trophic morphologies; a typical and a cannibalistic morph. Cannibalistic morphs, distinguished by enlarged vomerine teeth, wide heads, slender bodies, and cannibalistic tendencies, are often found where conspecifics occur at high density. During 2012 and 2013, 162 North Dakota wetlands and lakes were sampled for salamanders. Fifty-one contained A. mavortium populations; four of these contained cannibalistic morph individuals. Two populations with cannibalistic morphs occurred at sites with high abundances of conspecifics. However, the other two populations occurred at sites with unexpectedly low conspecific but high fathead minnow [Pimephales promelas (Rafinesque, 1820)] abundances. Further, no typical morphs were observed in either of these later two populations, contrasting with earlier research suggesting cannibalistic morphs only occur at low frequencies in salamander populations. Another anomaly of all four populations was the occurrence of cannibalistic morphs in permanent water sites, suggesting their presence was due to factors other than faster growth allowing them to occupy ephemeral habitats. Therefore, our findings suggest environmental factors inducing the cannibalistic morphism may be more complex than previously thought.

Expression Analysis of an R3-Type MYB Transcription Factor CPC-LIKE MYB4 (TRICHOMELESS2) and CPL4-Related Transcripts in Arabidopsis

PubMed Central

Tominaga-Wada, Rumi; Nukumizu, Yuka

2012-01-01

The CAPRICE (CPC)-like MYB gene family encodes R3-type MYB transcription factors in Arabidopsis. There are six additional CPC-like MYB sequences in the Arabidopsis genome, including TRYPTICHON (TRY), ENHANCER OF TRY AND CPC1 and 2 (ETC1 and ETC2), ENHANCER OF TRY AND CPC3/CPC-LIKE MYB3 (ETC3/CPL3), and TRICHOMELESS1 and 2 (TCL1 and TCL2). We independently identified CPC-LIKE MYB4 (CPL4), which was found to be identical to TCL2. RT-PCR analysis showed that CPL4 is strongly expressed in shoots, including true leaves, but not in roots. Promoter-GUS analyses indicated that CPL4 is specifically expressed in leaf blades. Although CPC expression was repressed in 35S::ETC1, 35S::ETC2 and 35S::CPL3 backgrounds, CPL4 expression was not affected by ETC1, ETC2 or CPL3 over-expression. Notably, several chimeric transcripts may result from inter-genic alternative splicing of CPL4 and ETC2, two tandemly repeated genes on chromosome II. At least two chimeric transcripts named CPL4-α and CPL4-β are expected to encode complete CPC-like MYB proteins. PMID:22489163

Morph-specific metabolic rate and the timing of reproductive senescence in a color polymorphic dragon.

PubMed

Friesen, Christopher R; Johansson, Rasmus; Olsson, Mats

2017-08-01

Polymorphism has fascinated biologists for over a century because morphs persist within populations through evolutionary time in spite of showing disparate behavioral and physiological phenotypes; any one morph should go to fixation with the slightest fitness advantage over the others. Surely there must be trade-offs that balance selection on them. The polychromatic morphs of the Australian painted dragon lizard, Ctenophorus pictus, are one such system. The male color morphs of painted dragons have different physiological and behavioral traits including reproductive tactics, hormone levels, and the rate of body condition loss through the reproductive season. Due to their differences in physiology and reproductive tactics, we tested the hypotheses that male morphs would differ in resting metabolic rates (RMRs) and that the morphs' RMR would decline at different rates through the mating season. We found that bib-morphs (yellow gular patch) differ in RMR with bibbed (more aggressive) males having consistently higher RMR than non-bibbed males. Furthermore, we show that male dragons experience a decline in RMR as they age from reproductively active to inactive. We also found that the RMR of bibbed males has higher repeatability than non-bibbed males. Our results reinforce previous hypotheses about the morph-specific costs of bearing a gular patch in painted dragons. © 2017 Wiley Periodicals, Inc.

Trade-offs in disease and bleaching susceptibility among two color morphs of the Hawaiian reef coral, Montipora capitata

NASA Astrophysics Data System (ADS)

Shore-Maggio, Amanda; Callahan, Sean M.; Aeby, Greta S.

2018-06-01

Two threats impacting coral reefs are bleaching and disease, and differential susceptibility to both exists among and within coral taxa. Bleaching resistance is commonly linked to the clade of endosymbiotic Symbiodinium, but may come at a cost to other biological traits. Montipora capitata is an Indo-Pacific reef-building coral with two color morphs, red and orange, which harbor different clades of Symbiodinium. We explored whether these color morphs displayed differences in bleaching/disease susceptibility and other biological traits (growth rate, reproductive output, and lipid content). We found a trade-off between disease and bleaching susceptibility. The orange morph had significantly higher disease prevalence, whereas the red morph had significantly higher bleaching prevalence. Thermal stress experiments found that bleaching and loss of photochemical efficiency occurred significantly faster in the red morph, but at normal temperatures, the red morph had a significantly higher growth rate. Higher abundance of the red morph in the field suggests that disease resistance is a more successful strategy in the absence of thermal stress events. The orange morph may better tolerate increases in sea temperatures, but may not persist due to decreased growth rate and increased disease susceptibility. Trade-offs in response to stressors highlight the need to consider local and global threats to coral reefs.

Co-Seeding Human Endothelial Cells with Human-Induced Pluripotent Stem Cell-Derived Mesenchymal Stem Cells on Calcium Phosphate Scaffold Enhances Osteogenesis and Vascularization in Rats.

PubMed

Liu, Xian; Chen, Wenchuan; Zhang, Chi; Thein-Han, Wahwah; Hu, Kevin; Reynolds, Mark A; Bao, Chongyun; Wang, Ping; Zhao, Liang; Xu, Hockin H K

2017-06-01

A major challenge in repairing large bone defects with tissue-engineered constructs is the poor vascularization in the defect. The lack of vascular networks leads to insufficient oxygen and nutrients supply, which compromises the survival of seeded cells. To achieve favorable regenerative effects, prevascularization of tissue-engineered constructs by co-culturing of endothelial cells and bone cells is a promising strategy. The aim of this study was to investigate the effects of human-induced pluripotent stem cell-derived mesenchymal stem cells (hiPSC-MSCs) co-cultured with human umbilical vein endothelial cells (HUVECs) for prevascularization of calcium phosphate cement (CPC) scaffold on bone regeneration in vivo for the first time. HUVECs co-cultured with hiPSC-MSCs formed microcapillary-like structures in vitro. HUVECs promoted mineralization of hiPSC-MSCs on CPC scaffolds. Four groups were tested in a cranial bone defect model in nude rats: (1) CPC scaffold alone (CPC control); (2) HUVEC-seeded CPC (CPC-HUVEC); (3) hiPSC-MSC-seeded CPC (CPC-hiPSC-MSC); and (4) HUVECs co-cultured with hiPSC-MSCs on CPC scaffolds (co-culture group). After 12 weeks, the co-culture group achieved the greatest new bone area percentage of 46.38% ± 3.8% among all groups (p < 0.05), which was more than four folds of the 10.61% ± 1.43% of CPC control. In conclusion, HUVECs co-cultured with hiPSC-MSCs substantially promoted bone regeneration. The novel construct of HUVECs co-cultured with hiPSC-MSCs delivered via CPC scaffolds is promising to enhance bone and vascular regeneration in orthopedic applications.

Protocol for evaluating the efficacy of cetylpyridinium chloride as a beef hide intervention.

PubMed

Bosilevac, Joseph M; Wheeler, Tommy L; Rivera-Betancourt, Mildred; Nou, Xiangwu; Arthur, Terrance M; Shackelford, Steven D; Kent, Matthew P; Jaroni, Divya; Osborn, Matthew S; Rossman, Michelle; Reagan, James O; Koohmaraie, Mohammad

2004-02-01

The objective of this study was to establish the necessary protocols and assess the efficacy of cetylpyridinium chloride (CPC) as an antimicrobial intervention on beef cattle hides. Experiments using CPC were conducted to determine (i) the methods of neutralization needed to obtain valid efficacy measurements, (ii) the effect of concentration and dwell time after treatment, (iii) the effect of CPC on hide and carcass microbial populations when cattle were treated at a feedlot and then transported to a processing facility for harvest, and (iv) the effectiveness of spray pressure and two-spray combinations of CPC and water to reduce hide microbial populations. Residual CPC in hide sponge samples prevented bacterial growth. Dey-Engley neutralization media at 7.8% and a centrifugation step were necessary to overcome this problem. All dwell times, ranging from 30 s to 4 h, after 1% CPC application to cattle hides resulted in aerobic plate counts and Enterobacteriaceae counts 1.5 log CFU/100 cm2 lower than controls. The most effective dose of CPC was 1%, which reduced aerobic plate counts and Enterobacteriaceae counts 2 and 1 log CFU/100 cm2, respectively. Low-pressure application of 1% CPC at the feedlot, transport to the processing facility, and harvest within 5 h of application resulted in no effect on Escherichia coli O157 prevalence on hides or preevisceration carcasses. Two high-pressure CPC washes lowered aerobic plate counts and Enterobacteriaceae counts by 4 log CFU/100 cm2, and two medium-pressure CPC washes were only slightly less effective. These results indicate that under the proper conditions, CPC may still be effective for reducing microbial populations on cattle hides. Further study is warranted to determine if this effect will result in reduction of hide-to-carcass contamination during processing.

Evidence for ontogenetically and morphologically distinct alternative reproductive tactics in the invasive Round Goby Neogobius melanostomus.

PubMed

Bleeker, Katinka; de Jong, Karen; van Kessel, Nils; Hinde, Camilla A; Nagelkerke, Leopold A J

2017-01-01

Alternative reproductive tactics are characterized by the occurrence of discrete alternative morphs that differ in behavioural, morphological and physiological traits within the same sex. Although much effort has been made to describe the behaviour, morphology and physiology of such alternative morphs, less effort has been invested investigating how much overlap there is in the characteristics of such morphs in natural populations. We studied random population samples of the invasive Round Goby Neogobius melanostomus from five different localities in the river Rhine system in the Netherlands. We found two morphologically and physiologically distinct male morphs which likely represent alternative reproductive tactics. Almost all mature males under 9.35 cm total length had a gonadosomatic index > 3%, suggestive of a sneaker tactic, while nearly all males above 9.35 cm has a gonadosomatic index of < 3%, suggestive of a parental tactic. Cheek size and eye diameter alone were sufficient to distinguish the two morphs. Gonads had a different relationship with size in the two morphs, indicating separate growth trajectories. The gonad mass of sneaker morphs would be ca. 7.5 times as high as the gonad mass of parental morphs of the same total length after extrapolation. Few (9%) intermediates were found, suggesting that the expression of alternative reproductive tactics is determined before the first breeding season. This contrasts with studies on other goby species, which show evidence of plastic tactics that can be affected by social circumstances. We conclude that it is possible to distinguish two alternative male morphs in the Dutch Round Goby population using morphological measurements alone. Although behavioural observations are needed to provide conclusive evidence, the difference in GSI between these morphs indicates that these morphs reflect alternative reproductive tactics.

Evidence for ontogenetically and morphologically distinct alternative reproductive tactics in the invasive Round Goby Neogobius melanostomus

PubMed Central

de Jong, Karen; van Kessel, Nils; Hinde, Camilla A.; Nagelkerke, Leopold A. J.

2017-01-01

Alternative reproductive tactics are characterized by the occurrence of discrete alternative morphs that differ in behavioural, morphological and physiological traits within the same sex. Although much effort has been made to describe the behaviour, morphology and physiology of such alternative morphs, less effort has been invested investigating how much overlap there is in the characteristics of such morphs in natural populations. We studied random population samples of the invasive Round Goby Neogobius melanostomus from five different localities in the river Rhine system in the Netherlands. We found two morphologically and physiologically distinct male morphs which likely represent alternative reproductive tactics. Almost all mature males under 9.35 cm total length had a gonadosomatic index > 3%, suggestive of a sneaker tactic, while nearly all males above 9.35 cm has a gonadosomatic index of < 3%, suggestive of a parental tactic. Cheek size and eye diameter alone were sufficient to distinguish the two morphs. Gonads had a different relationship with size in the two morphs, indicating separate growth trajectories. The gonad mass of sneaker morphs would be ca. 7.5 times as high as the gonad mass of parental morphs of the same total length after extrapolation. Few (9%) intermediates were found, suggesting that the expression of alternative reproductive tactics is determined before the first breeding season. This contrasts with studies on other goby species, which show evidence of plastic tactics that can be affected by social circumstances. We conclude that it is possible to distinguish two alternative male morphs in the Dutch Round Goby population using morphological measurements alone. Although behavioural observations are needed to provide conclusive evidence, the difference in GSI between these morphs indicates that these morphs reflect alternative reproductive tactics. PMID:28369128

Negative frequency-dependent selection or alternative reproductive tactics: maintenance of female polymorphism in natural populations

PubMed Central

2013-01-01

Background Sex-limited polymorphisms have long intrigued evolutionary biologists and have been the subject of long-standing debates. The coexistence of multiple male and/or female morphs is widely believed to be maintained through negative frequency-dependent selection imposed by social interactions. However, remarkably few empirical studies have evaluated how social interactions, morph frequencies and fitness parameters relate to one another under natural conditions. Here, we test two hypotheses proposed to explain the maintenance of a female polymorphism in a species with extreme geographical variation in morph frequencies. We first elucidate how fecundity traits of the morphs vary in relation to the frequencies and densities of males and female morphs in multiple sites over multiple years. Second, we evaluate whether the two female morphs differ in resource allocation among fecundity traits, indicating alternative tactics to maximize reproductive output. Results We present some of the first empirical evidence collected under natural conditions that egg number and clutch mass was higher in the rarer female morph. This morph-specific fecundity advantage gradually switched with the population morph frequency. Our results further indicate that all investigated fecundity traits are negatively affected by relative male density (i.e. operational sex ratio), which confirms male harassment as selective agent. Finally, we show a clear trade-off between qualitative (egg mass) and quantitative (egg number) fecundity traits. This trade-off, however, is not morph-specific. Conclusion Our reported frequency- and density-dependent fecundity patterns are consistent with the hypothesis that the polymorphism is driven by a conflict between sexes over optimal mating rate, with costly male sexual harassment driving negative frequency-dependent selection on morph fecundity. PMID:23822745

Water temperature, not fish morph, determines parasite infections of sympatric Icelandic threespine sticklebacks (Gasterosteus aculeatus)

PubMed Central

Karvonen, Anssi; Kristjánsson, Bjarni K; Skúlason, Skúli; Lanki, Maiju; Rellstab, Christian; Jokela, Jukka

2013-01-01

Parasite communities of fishes are known to respond directly to the abiotic environment of the host, for example, to water quality and water temperature. Biotic factors are also important as they affect the exposure profile through heterogeneities in parasite distribution in the environment. Parasites in a particular environment may pose a strong selection on fish. For example, ecological differences in selection by parasites have been hypothesized to facilitate evolutionary differentiation of freshwater fish morphs specializing on different food types. However, as parasites may also respond directly to abiotic environment the parasite risk does not depend only on biotic features of the host environment. It is possible that different morphs experience specific selection gradients by parasites but it is not clear how consistent the selection is when abiotic factors change. We examined parasite pressure in sympatric morphs of threespine stickleback (Gasterosteus aculeatus) across a temperature gradient in two large Icelandic lakes, Myvatn and Thingvallavatn. Habitat-specific temperature gradients in these lakes are opposite. Myvatn lava rock morph lives in a warm environment, while the mud morph lives in the cold. In Thingvallavatn, the lava rock morph lives in a cold environment and the mud morph in a warm habitat. We found more parasites in fish living in higher temperature in both lakes, independent of the fish morph, and this pattern was similar for the two dominating parasite taxa, trematodes and cestodes. However, at the same time, we also found higher parasite abundance in a third morph living in deep cold–water habitat in Thingvallavatn compared to the cold-water lava morph, indicating strong effect of habitat-specific biotic factors. Our results suggest complex interactions between water temperature and biotic factors in determining the parasite community structure, a pattern that may have implications for differentiation of stickleback morphs. PMID:23789063

Diurnal and developmental differences in gene expression between adult dispersing and flightless morphs of the wing polymorphic cricket, Gryllus firmus: Implications for life-history evolution.

PubMed

Zera, Anthony J; Vellichirammal, Neetha Nanoth; Brisson, Jennifer A

2018-04-12

The functional basis of life history adaptation is a key topic of research in life history evolution. Studies of wing-polymorphism in the cricket Gryllus firmus have played a prominent role in this field. However, prior in-depth investigations of morph specialization have primarily focused on a single hormone, juvenile hormone, and a single aspect of intermediary metabolism, the fatty-acid biosynthetic component of lipid metabolism. Moreover, the role of diurnal variation in life history adaptation in G. firmus has been understudied, as is the case for organisms in general. Here, we identify genes whose expression differs consistently between the morphs independent of time-of-day during early adulthood, as well as genes that exhibit a strong pattern of morph-specific diurnal expression. We find strong, consistent, morph-specific differences in the expression of genes involved in endocrine regulation, carbohydrate and lipid metabolism, and immunity - in particular, in the expression of an insulin-like-peptide precursor gene and genes involved in triglyceride production. We also find that the flight-capable morph exhibited a substantially greater number of genes exhibiting diurnal change in gene expression compared with the flightless morph, correlated with the greater circadian change in the hemolymph juvenile titer in the dispersing morph. In fact, diurnal differences in expression within the dispersing morph at different times of the day were significantly greater in magnitude than differences between dispersing and flightless morphs at the same time-of-day. These results provide important baseline information regarding the potential role of variable gene expression on life history specialization in morphs of G. firmus, and the first information on genetically-variable, diurnal change in gene expression, associated with a key life history polymorphism. These results also suggest the existence of prominent morph-specific circadian differences in gene expression in G. firmus, possibly caused by the morph-specific circadian rhythm in the juvenile hormone titer. Copyright © 2018 Elsevier Ltd. All rights reserved.

HPLC-ELSD Quantification and Centrifugal Partition Chromatography Isolation of 8-O-Acetylharpagide from Oxera coronata (Lamiaceae).

PubMed

Remeur, Camille; Le Borgne, Erell; Gauthier, Léa; Grougnet, Raphaël; Deguin, Brigitte; Poullain, Cyril; Litaudon, Marc

2017-05-01

Iridoid glycosides possess highly functionalised monoterpenoid aglycon with several contiguous stereocentres. For the most common, they are often present in quantities reaching several percentage of the fresh plant weight, and thus they may be regarded as starting material for the synthesis of a number of new chiral and bioactive molecules. To quantify and to isolate 8-O-acetylharpagide (AH) from several extracts of Oxera coronata R.P.J. de Kok, a Lamiaceae species endemic to New Caledonia, using HPLC-ELSD (evaporative light scattering detector) and centrifugal partition chromatography (CPC). Oxera coronata produces high amounts of AH in leaves, twigs and fruits. Water and methanol extracts of these plant parts were prepared. The content of AH in each extract was quantified by HPLC-ELSD, using acetonitrile-water (+0.1% formic acid) gradient elution. The HPLC method was validated for precision, linearity, limit of detection (LOD), limit of quantification (LOQ) and accuracy. A ternary solvent system ethyl acetate/n-propanol/water (3:2:5, v/v/v) was selected and applied to recover the target compound using Spot CPC from the leaves aqueous extract. HPLC-ELSD analysis followed by CPC purification led to the efficient isolation of AH from O. coronata leaves aqueous extract. HPLC-ELSD has proven to be a well-adapted detection and quantification method for iridoid glycosides, while CPC confirmed to be an efficient technique for the isolation of polar compounds. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Preparative enantiomer separation of dichlorprop with a cinchona-derived chiral selector employing centrifugal partition chromatography and high-performance liquid chromatography: a comparative study.

PubMed

Gavioli, Elena; Maier, Norbert M; Minguillón, Cristina; Lindner, Wolfgang

2004-10-01

A countercurrent chromatography protocol for support-free preparative enantiomer separation of the herbicidal agent 2-(2,4-dichlorphenoxy)propionic acid (dichlorprop) was developed utilizing a purposefully designed, highly enantioselective chiral stationary-phase additive (CSPA) derived from bis-1,4-(dihydroquinidinyl)phthalazine. Guided by liquid-liquid extraction experiments, a solvent system consisting of 10 mM CSPA in methyl tert-butyl ether and 100 mM sodium phosphate buffer (pH 8.0) was identified as a suitable stationary/mobile-phase combination. This solvent system provided an ideal compromise among stationary-phase retention, enantioselectivity, and well-balanced analyte distribution behavior. Using a commercial centrifugal partition chromatography instrument, complete enantiomer separations of up to 366 mg of racemic dichlorprop could be achieved, corresponding to a sample load being equivalent to the molar amount of CSPA employed. Comparison of the preparative performance characteristics of the CPC protocol with that of a HPLC separation using a silica-supported bis-1,4-(dihydroquinidinyl)phthalazine chiral stationary phase CSP revealed comparable loading capacities for both techniques but a significantly lower solvent consumption for CPC. With respect to productivity, HPLC was found to be superior, mainly due to inherent flow rate restrictions of the CPC instrument. Given that further progress in instrumental design and engineering of dedicated, highly enantioselective CSPAs can be achieved, CPC may offer a viable alternative to CSP-based HPLC for preparative-scale enantiomer separation.

The role of rare morph advantage and conspicuousness in the stable gold-dark colour polymorphism of a crater lake Midas cichlid fish.

PubMed

Torres-Dowdall, Julián; Golcher-Benavides, Jimena; Machado-Schiaffino, Gonzalo; Meyer, Axel

2017-09-01

Genetically based stable colour polymorphisms provide a unique opportunity to study the evolutionary processes that preserve genetic variability in the wild. Different mechanisms are proposed to promote the stability of polymorphisms, but only few empirical examples have been documented, resulting in an incomplete understanding of these mechanisms. A remarkable genetically determined stable colour polymorphism is found in the Nicaraguan Midas cichlid species complex (Amphilophus cf. citrinellus). All Midas cichlids start their life with a dark-grey coloration (dark morph), but individuals carrying the dominant "gold" allele (c. 10%) lose their melanophores later in life, revealing the underlying orange coloration (gold morph). How this polymorphism is maintained remains unclear. Two main hypotheses have been proposed, both suggesting differential predation upon colour morphs as the proximate mechanism. One predicts that the conspicuous gold morph is more likely to be preyed upon, but this disadvantage is balanced by their competitive dominance over the dark morph. The second hypothesis suggests a rare morph advantage where the rarer gold morph experiences less predation. Empirical evidence for either of these mechanisms is still circumstantial and inconclusive. We conducted two field experiments in a Nicaraguan crater lake using wax models simulating both morphs to determine predation pressure upon Midas cichlid colour morphs. First, we tested the interaction of coloration and depth on attack rate. Second, we tested the interaction of fish size and coloration. We contrasted the pattern of attacks from these experiments to the predicted predation patterns from the hypotheses proposed to explain the colour polymorphism's stability. Large models imitating colour morphs were attacked at similar rates irrespectively of their position in the water column. Yet, attacks upon small models resembling juveniles were directed mainly towards dark models. This resulted in a significant size-by-colour interaction. We suggest that gold Midas cichlids experience a rare morph advantage as juveniles when individuals of this morph are extremely uncommon. But this effect is reduced or disappears among adults, where gold individuals are relatively more common. Thus, the interaction of rare morph advantage and conspicuousness, rather than either of those factors alone, is a likely mechanism resulting in the stability of the colour polymorphism in Midas cichlids. © 2017 The Authors. Journal of Animal Ecology © 2017 British Ecological Society.

Computer-assisted sperm morphometry fluorescence-based analysis has potential to determine progeny sex.

PubMed

Santolaria, Pilar; Pauciullo, Alfredo; Silvestre, Miguel A; Vicente-Fiel, Sandra; Villanova, Leyre; Pinton, Alain; Viruel, Juan; Sales, Ester; Yániz, Jesús L

2016-01-01

This study was designed to determine the ability of computer-assisted sperm morphometry analysis (CASA-Morph) with fluorescence to discriminate between spermatozoa carrying different sex chromosomes from the nuclear morphometrics generated and different statistical procedures in the bovine species. The study was divided into two experiments. The first was to study the morphometric differences between X- and Y-chromosome-bearing spermatozoa (SX and SY, respectively). Spermatozoa from eight bulls were processed to assess simultaneously the sex chromosome by FISH and sperm morphometry by fluorescence-based CASA-Morph. SX cells were larger than SY cells on average (P < 0.001) although with important differences between bulls. A simultaneous evaluation of all the measured features by discriminant analysis revealed that nuclear area and average fluorescence intensity were the variables selected by stepwise discriminant function analysis as the best discriminators between SX and SY. In the second experiment, the sperm nuclear morphometric results from CASA-Morph in nonsexed (mixed SX and SY) and sexed (SX) semen samples from four bulls were compared. FISH allowed a successful classification of spermatozoa according to their sex chromosome content. X-sexed spermatozoa displayed a larger size and fluorescence intensity than nonsexed spermatozoa (P < 0.05). We conclude that the CASA-Morph fluorescence-based method has the potential to find differences between X- and Y-chromosome-bearing spermatozoa in bovine species although more studies are needed to increase the precision of sex determination by this technique.

On the potential of Galileo E5 for time transfer.

PubMed

Martínez-Belda, Mari Carmen; Defraigne, Pascale; Bruyninx, Carine

2013-01-01

The main global navigation satellite systems (GNSS) technique currently used for accurate time and frequency transfer is based on an analysis of the ionosphere-free combinations of dual-frequency code and carrier phase measurements in a precise point positioning (PPP) mode. This technique analyses the observations of one GNSS station using external products for satellite clocks and orbits to determine the position and clock synchronization errors of this station. The frequency stability of this time transfer is limited by the noise and multipath of the Global Positioning System (GPS) and Globalnaya Navigatsionnaya Sputnikovaya Sistema (GLONASS) codes. In the near future, Galileo will offer a broadband signal E5, with low noise in the centimeter range and with the lowest multipath error ever observed. This paper investigates new analysis procedures based on the E5 codeplus- carrier (CPC) combination for time transfer. The CPC combination with E5 provides a noise level 10 times lower than the ionosphere-free combination of Galileo E1 and E5, which is very promising for improving GNSS time transfer performances. From some tests with simulated Galileo data, it is shown here that the use of the CPC combination with E5 does not improve, at present, the medium- and long-term stability of time transfer with respect to the ionosphere-free combination of Galileo E1 and E5 codes, because of the need for a second frequency signal to correct for the ionospheric delays and ambiguities.

Recent Developments in Production and Biotechnological Applications of C-Phycocyanin

PubMed Central

Kuddus, M.; Singh, P.; Thomas, G.; Al-Hazimi, Awdah

2013-01-01

An extensive range of pigments including phycobiliproteins are present in algae. C-phycocyanin (C-PC), a phycobiliprotein, is one of the key pigments of Spirulina, a microalgae used in many countries as a dietary supplement. Algal pigments have massive commercial value as natural colorants in nutraceutical, cosmetics, and pharmaceutical industries, besides their health benefits. At present, increasing awareness of harmful effects of synthetic compounds and inclination of community towards the usage of natural products have led to the exploitation of microalgae as a source of natural pigments/colors. This review describes recent findings about the sources and production of C-PC, with emphasis on specific techniques for extraction and purification, along with potential industrial applications in diagnostics, foods, cosmetics, and pharmaceutical industries. PMID:24063013

Recent developments in production and biotechnological applications of C-phycocyanin.

PubMed

Kuddus, M; Singh, P; Thomas, G; Al-Hazimi, Awdah

2013-01-01

An extensive range of pigments including phycobiliproteins are present in algae. C-phycocyanin (C-PC), a phycobiliprotein, is one of the key pigments of Spirulina, a microalgae used in many countries as a dietary supplement. Algal pigments have massive commercial value as natural colorants in nutraceutical, cosmetics, and pharmaceutical industries, besides their health benefits. At present, increasing awareness of harmful effects of synthetic compounds and inclination of community towards the usage of natural products have led to the exploitation of microalgae as a source of natural pigments/colors. This review describes recent findings about the sources and production of C-PC, with emphasis on specific techniques for extraction and purification, along with potential industrial applications in diagnostics, foods, cosmetics, and pharmaceutical industries.

Nuclear Trapping Controls the Position-Dependent Localization of CAPRICE in the Root Epidermis of Arabidopsis1[C][W

PubMed Central

Kang, Yeon Hee; Song, Sang-Kee; Schiefelbein, John; Lee, Myeong Min

2013-01-01

Cell fate determination and differentiation are central processes in the development of multicellular organisms, and the Arabidopsis (Arabidopsis thaliana) root epidermis provides a model system to study the molecular basis of these processes. A lateral inhibition mechanism mediated by an R3 single-repeat MYB protein, CAPRICE (CPC), has been proposed to explain the specification of the two types of root epidermal cells (hair cells and nonhair cells). However, it is not clear how CPC acts preferentially in the H-position cells, rather than the N-position cells, where its gene is expressed. To explore this issue, we examined the effect of misexpressed CPC on cell fate specification and CPC localization in the root epidermis. We show that CPC is able to move readily within the root epidermis when its expression level is high and that CPC can induce the hair cell fate in a cell-autonomous manner. We provide evidence that CPC is capable of moving from the stele tissue in the center of the root to the outermost epidermal layer, where it can induce the hair cell fate. In addition, we show that CPC protein accumulates primarily in the nuclei of H-position cells in the early meristematic region, and this localization requires the H-cell-expressed ENHANCER OF GLABRA3 (EGL3) basic helix-loop-helix transcription factor. These results suggest that cell-cell movement of CPC occurs readily within the meristematic region of the root and that EGL3 preferentially traps the CPC protein in the H-position cells of the epidermis. PMID:23832626

DETERMINATION OF THE MAXIMUM INHIBITORY DILUTION OF CETYLPYRIDINIUM CHLORIDE-BASED MOUTHWASHES AGAINST STAPHYLOCOCCUS AUREUS: AN IN VITRO STUDY

PubMed Central

Watanabe, Evandro; Tanomaru, Juliane Maria Guerreiro; Nascimento, Andresa Piacezzi; Matoba, Fumio; Tanomaru, Mario; Ito, Izabel Yoko

2008-01-01

The aim of this in vitro study was to determine the maximum inhibitory dilution (MID) of four cetylpyridinium chloride (CPC)-based mouthwashes: CPC+Propolis, CPC+Malva, CPC+Eucaliptol+Juá+Romã+Propolis (Natural Honey®) and CPC (Cepacol®), against 28 Staphylococcus aureus field strains, using the agar dilution method. Decimal dilutions ranging from 1/10 to 1/ 655,360 were prepared and added to Mueller Hinton Agar. Strains were inoculated using Steers multipoint inoculator. The inocula were seeded onto the surface of the culture medium in Petri dishes containing different dilutions of the mouthwashes. The dishes were incubated at 37°C for 24 h. For readings, the MID was considered as the maximum dilution of mouthwash still capable of inhibiting microbial growth. The obtained data showed that CPC+Propolis had antimicrobial activity against 27 strains at 1/320 dilution and against all 28 strains at 1/160 dilution, CPC+Malva inhibited the growth of all 28 strains at 1/320 dilution, CPC+Eucaliptol+Juá+Romã+Propolis inhibited the growth of 2 strains at 1/640 dilution and all 28 strains at 1/320 dilution, and Cepacol® showed antimicrobial activity against 3 strains at 1/320 dilution and against all 28 strains at 1/160 dilution. Data were submitted to Kruskal-Wallis test, showing that the MID of Cepacol® was lower than that determined for the other products (p<0.05). In conclusion, CPC-mouthwashes showed antimicrobial activity against S. aureus and the addition of other substances to CPC improved its antimicrobial effect. PMID:19089260

Plumage polymorphism and fitness in Swainson's hawks.

PubMed

Briggs, C W; Collopy, M W; Woodbridge, B

2011-10-01

We examine the maintenance of a plumage polymorphism, variation in plumages among the same age and sex class within a population, in a population of Swainson's Hawks. We take advantage of 32 years of data to examine two prevalent hypotheses used to explain the persistence of morphs: apostatic selection and heterozygous advantage. We investigate differences in fitness among three morph classes of a melanistic trait in Swainson's Hawks: light (7% of the local breeding population), intermediate (57%) and dark (36%). Specifically, we examined morph differences in adult apparent survival, breeding success, annual number of fledglings produced, probability of offspring recruitment into the breeding population and lifetime reproductive success (LRS). If apostatic selection were a factor in maintaining morphs, we would expect that individuals with the least frequent morph would perform best in one or more of these fitness categories. Alternatively, if heterozygous advantage played a role in the maintenance of this polymorphism, we would expect heterozygotes (i.e. intermediate morphs) to have one or more increased rates in these categories. We found no difference in adult apparent survival between morph classes. Similarly, there were no differences in breeding success, nest productivity, LRS or probability of recruitment of offspring between parental morph. We conclude that neither apostatic selection nor heterozygous advantage appear to play a role in maintaining morphs in this population. © 2011 The Authors. Journal of Evolutionary Biology © 2011 European Society For Evolutionary Biology.

Energy-based aeroelastic analysis of a morphing wing

NASA Astrophysics Data System (ADS)

De Breuker, Roeland; Abdalla, Mostafa; Gürdal, Zafer; Lindner, Douglas

2007-04-01

Aircraft are often confronted with distinct circumstances during different parts of their mission. Ideally the aircraft should fly optimally in terms of aerodynamic performance and other criteria in each one of these mission requirements. This requires in principle as many different aircraft configurations as there are flight conditions, so therefore a morphing aircraft would be the ideal solution. A morphing aircraft is a flying vehicle that i) changes its state substantially, ii) provides superior system capability and iii) uses a design that integrates innovative technologies. It is important for such aircraft that the gains due to the adaptability to the flight condition are not nullified by the energy consumption to carry out the morphing manoeuvre. Therefore an aeroelastic numerical tool that takes into account the morphing energy is needed to analyse the net gain of the morphing. The code couples three-dimensional beam finite elements model in a co-rotational framework to a lifting-line aerodynamic code. The morphing energy is calculated by summing actuation moments, applied at the beam nodes, multiplied by the required angular rotations of the beam elements. The code is validated with NASTRAN Aeroelasticity Module and found to be in agreement. Finally the applicability of the code is tested for a sweep morphing manoeuvre and it has been demonstrated that sweep morphing can improve the aerodynamic performance of an aircraft and that the inclusion of aeroelastic effects is important.

Development of Thermally Actuated, High-Temperature Composite Morphing Concepts

DTIC Science & Technology

2016-05-11

Thermally Actuated, High- Temperature Composite Morphing Concepts 5a. CONTRACT NUMBER EOARD 14-0063 5b. GRANT NUMBER FA9550-14-1-0063 5c...mismatched thermal expansion coefficients. However, current bimorphs are generally limited to benign temperatures and linear temperature displacement... temperature morphing structures. Successful application of this work may yield morphing hot structures in extreme environments. A particularly appealing

Development of Thermally Actuated, High Temperature Composite Morphing Concepts

DTIC Science & Technology

2016-03-31

Thermally Actuated, High- Temperature Composite Morphing Concepts 5a. CONTRACT NUMBER EOARD 14-0063 5b. GRANT NUMBER FA9550-14-1-0063 5c...mismatched thermal expansion coefficients. However, current bimorphs are generally limited to benign temperatures and linear temperature displacement... temperature morphing structures. Successful application of this work may yield morphing hot structures in extreme environments. A particularly appealing

Performance of a non-tapered 3D morphing wing with integrated compliant ribs

NASA Astrophysics Data System (ADS)

Previtali, F.; Ermanni, P.

2012-05-01

Morphing wings have a high potential for improving the performance and reducing the fuel consumption of modern aircraft. Thanks to its simplicity, the compliant belt-rib concept is regarded by the authors as a promising solution. Using the compliant rib designed by Hasse and Campanile as a starting point, a compliant morphing wing made of composite materials is designed. Innovative methods for optimal placing of the actuation and for the quantification of the morphing are used. The performance of the compliant morphing wing in terms of three-dimensional (3D) structural behaviour and aerodynamic properties, both two- and three-dimensional, is presented and discussed. The fundamental importance of considering 3D coupling effects in the determination of the performance of morphing aerofoils is shown.

Climate Prediction Center - 6 to 10 Day Outlook

Science.gov Websites

/PNA/AAO About Us Our Mission Who We Are Contact Us CPC Information CPC Web Team Product Feedback 6-10 . Government's official Web portal to all Federal, state and local government Web resources and services. HOME> Used, 8 to 14 Day Outlooks, Heat Index, Our Mission, Who We Are, CPC Information, CPC Web Team NOAA

Climate Prediction Center - 8 to 14 Day Outlook

Science.gov Websites

/PNA/AAO About Us Our Mission Who We Are Contact Us CPC Information CPC Web Team Product Feedback 8-14 . Government's official Web portal to all Federal, state and local government Web resources and services. HOME> Used, 6 to 10 Day Outlooks, Heat Index, Our Mission, Who We Are, CPC Information, CPC Web Team NOAA

Ongoing niche differentiation under high gene flow in a polymorphic brackish water threespine stickleback (Gasterosteus aculeatus) population.

PubMed

Østbye, Kjartan; Taugbøl, Annette; Ravinet, Mark; Harrod, Chris; Pettersen, Ruben Alexander; Bernatchez, Louis; Vøllestad, Leif Asbjørn

2018-02-05

Marine threespine sticklebacks colonized and adapted to brackish and freshwater environments since the last Pleistocene glacial. Throughout the Holarctic, three lateral plate morphs are observed; the low, partial and completely plated morph. We test if the three plate morphs in the brackish water Lake Engervann, Norway, differ in body size, trophic morphology (gill raker number and length), niche (stable isotopes; δ 15 N, δ 13 C, and parasites (Theristina gasterostei, Trematoda spp.)), genetic structure (microsatellites) and the lateral-plate encoding Stn382 (Ectodysplasin) gene. We examine differences temporally (autumn 2006/spring 2007) and spatially (upper/lower sections of the lake - reflecting low versus high salinity). All morphs belonged to one gene pool. The complete morph was larger than the low plated, with the partial morph intermediate. The number of lateral plates ranged 8-71, with means of 64.2 for complete, 40.3 for partial, and 14.9 for low plated morph. Stickleback δ 15 N was higher in the lower lake section, while δ 13 C was higher in the upper section. Stickleback isotopic values were greater in autumn. The low plated morph had larger variances in δ 15 N and δ 13 C than the other morphs. Sticklebacks in the upper section had more T. gasterostei than in the lower section which had more Trematoda spp. Sticklebacks had less T. gasterostei, but more Trematoda spp. in autumn than spring. Sticklebacks with few and short rakers had more T. gasterostei, while sticklebacks with longer rakers had more Trematoda. spp. Stickleback with higher δ 15 N values had more T. gasterostei, while sticklebacks with higher δ 15 N and δ 13 C values had more Trematoda spp. The low plated morph had fewer Trematoda spp. than other morphs. Trait-ecology associations may imply that the three lateral plate morphs in the brackish water lagoon of Lake Engervann are experiencing ongoing divergent selection for niche and migratory life history strategies under high gene flow. As such, the brackish water zone may generally act as a generator of genomic diversity to be selected upon in the different environments where threespine sticklebacks can live.

In Vitro Evaluation of Mitochondrial Function and Estrogen Signaling in Cell Lines Exposed to the Antiseptic Cetylpyridinium Chloride

PubMed Central

Datta, Sandipan; He, Guochun; Tomilov, Alexey; Sahdeo, Sunil; Denison, Michael S.

2017-01-01

Background: Quaternary ammonium salts (QUATS), such as cetylpyridinium chloride (CPC) and benzalkonium chloride (BAK), are frequently used in antiseptic formulations, including toothpastes, mouthwashes, lozenges, throat and nasal sprays, and as biocides. Although in a recent ruling, the U.S. Food and Drug Administration (FDA) banned CPC from certain products and requested more data on BAK’s efficacy and safety profile, QUATS, in general, and CPC and BAK, in particular, continue to be used in personal health care, food, and pharmaceutical and cleaning industries. Objectives: We aimed to assess CPC's effects on mitochondrial toxicity and endocrine disruption in vitro. Method: Mitochondrial O2 consumption and adenosine triphosphate (ATP) synthesis rates of osteosarcoma cybrid cells were measured before and after CPC and BAK treatment. Antiestrogenic effects of the compounds were measured by a luciferase-based assay using recombinant human breast carcinoma cells (VM7Luc4E2, ERalpha-positive). Results: CPC inhibited both mitochondrial O2 consumption [half maximal inhibitory concentration (IC50): 3.8μM] and ATP synthesis (IC50: 0.9μM), and additional findings supported inhibition of mitochondrial complex 1 as the underlying mechanism for these effects. In addition, CPC showed concentration-dependent antiestrogenic activity half maximal effective concentration [(EC50): 4.5μM)]. BAK, another antimicrobial QUATS that is structurally similar to CPC, and the pesticide rotenone, a known complex 1 inhibitor, also showed mitochondrial inhibitory and antiestrogenic effects. In all three cases, there was overlap of the antiestrogenic activity with the mitochondrial inhibitory activity. Conclusions: Mitochondrial inhibition in vitro occurred at a CPC concentration that may be relevant to human exposures. The antiestrogenic activity of CPC, BAK, rotenone, and triclosan may be related to their mitochondrial inhibitory activity. Our findings support the need for additional research on the mitochondrial inhibitory and antiestrogenic effects of QUATS, including CPC and BAK. https://doi.org/10.1289/EHP1404 PMID:28885978

C-Phycocyanin protects against acute tributyltin chloride neurotoxicity by modulating glial cell activity along with its anti-oxidant and anti-inflammatory property: A comparative efficacy evaluation with N-acetyl cysteine in adult rat brain.

PubMed

Mitra, Sumonto; Siddiqui, Waseem A; Khandelwal, Shashi

2015-08-05

Spirulina is a widely used health supplement and is a dietary source of C-Phycocyanin (CPC), a potent anti-oxidant. We have previously reported the neurotoxic potential of tributyltin chloride (TBTC), an environmental pollutant and potent biocide. In this study, we have evaluated the protective efficacy of CPC against TBTC induced neurotoxicity. To evaluate the extent of neuroprotection offered by CPC, its efficacy was compared with the degree of protection offered by N-acetylcysteine (NAC) (a well known neuroprotective drug, taken as a positive control). Male Wistar rats (28 day old) were administered with 20mg/kg TBTC (oral) and 50mg/kg CPC or 50mg/kg NAC (i.p.), alone or in combination, and various parameters were evaluated. These include blood-brain barrier (BBB) damage; redox parameters (ROS, GSH, redox pathway associated enzymes, oxidative stress markers); inflammatory, cellular, and stress markers; apoptotic proteins and in situ cell death assay (TUNEL). We observed increased CPC availability in cortical tissue following its administration. Although BBB associated proteins like claudin-5, p-glycoprotein and ZO-1 were restored, CPC/NAC failed to protect against TBTC induced overall BBB permeability (Evans blue extravasation). Both CPC and NAC remarkably reduced oxidative stress and inflammation. NAC effectively modulated redox pathway associated enzymes whereas CPC countered ROS levels efficiently. Interestingly, CPC and NAC were equivalently capable of reducing apoptotic markers, astroglial activation and cell death. This study illustrates the various pathways involved in CPC mediated neuroprotection against this environmental neurotoxicant and highlights its capability to modulate glial cell activity. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Preference for Male Traits Differ in Two Female Morphs of the Tree Lizard, Urosaurus ornatus

PubMed Central

Lattanzio, Matthew S.; Metro, Kevin J.; Miles, Donald B.

2014-01-01

Non-random female mating preferences may contribute to the maintenance of phenotypic variation in color polymorphic species. However, the effect of female preference depends on the types of male traits used as signals by receptive females. If preference signals derive from discrete male traits (i.e., morph-specific), female preferences may rapidly fix to a morph. However, female preference signals may also include condition-dependent male traits. In this scenario, female preference may differ depending on the social context (i.e., male morph availability). Male tree lizards (Urosaurus ornatus) exhibit a dewlap color polymorphism that covaries with mating behavior. Blue morph males are aggressive and defend territories, yellow males are less aggressive and defend smaller territories, and orange males are typically nomadic. Female U. ornatus are also polymorphic in dewlap color, but the covariation between dewlap color and female behavior is unknown. We performed an experiment to determine how female mate choice depends on the visual and chemical signals produced by males. We also tested whether female morphs differ in their preferences for these signals. Female preferences involved both male dewlap color and size of the ventral color patch. However, the female morphs responded to these signals differently and depended on the choice between the types of male morphs. Our experiment revealed that females may be capable of distinguishing among the male morphs using chemical signals alone. Yellow females exhibit preferences based on both chemical and visual signals, which may be a strategy to avoid ultra-dominant males. In contrast, orange females may prefer dominant males. We conclude that female U. ornatus morphs differ in mating behavior. Our findings also provide evidence for a chemical polymorphism among male lizards in femoral pore secretions. PMID:25033282

Design and aerodynamic characteristics of a span morphing wing

NASA Astrophysics Data System (ADS)

Yu, Yuemin; Liu, Yanju; Leng, Jinsong

2009-03-01

Flight vehicles are often designed to function around a primary operating point such as an efficient cruise or a high maneuverability mode. Performance and efficiency deteriorate rapidly as the airplane moves towards other portions of the flight envelope. One solution to this quandary is to radically change the shape of the aircraft. This yields both improved efficiency and a larger flight envelope. This global shape change is an example of morphing aircraft . One concept of morphing is the span morphing wing in which the wingspan is varied to accommodate multiple flight regimes. This type of design allows for at least two discreet modes of the aircraft. The original configuration, in which the extensible portion of the wing is fully retracted, yields a high speed dash mode. Fully extending the wing provides the aircraft with a low speed mode tailored for fine tracking and loiter tasks. This paper discusses the design of a span morphing wing that permits a change in the aspect ratio while simultaneously supporting structural wing loads. The wing cross section is maintained by NACA 4412 rib sections . The span morphing wing was investigated in different configurations. The wing area and the aspect ratio of the span morphing wing increase as the wings pan increases. Computational aerodynamics are used to estimate the performance and dynamic characteristics of each wing shape of this span morphing wing as its wingspan is changed. Results show that in order to obtain the same lift, the conventional wing requires a larger angle of attach(AOA) than that of the span morphing wing.The lift of the span morphing wing increases as the wing span ,Mach number and AOA increases.

CD59 Underlines the Antiatherosclerotic Effects of C-Phycocyanin on Mice

PubMed Central

Chu, Xian-Ming; Xu, Ying-Jie; Yang, Fan; Lv, Cong-Yi; Nie, Shu-min

2013-01-01

The effects of C-phycocyanin (C-PC) on atherosclerosis and the regulatory effects of CD59 gene on anti-atherosclerotic roles of C-PC were investigated. Apolipoprotein E knockout (ApoE(−/−)) mice were randomly divided into four groups: control group, C-PC treatment group, CD59 transfection group and C-PC+CD59 synergy group. The mice were fed with high-fat-diet and treated with drug intervention at the same time. Results showed the atherosclerotic mouse model was successfully established. CD59 was over-expressed in blood and tissue cells. Single CD59 or C-PC could reduce blood lipid levels and promote the expression of anti-apoptotic Bcl-2 but inhibit pro-apoptotic Fas proteins in endothelial cells. The expression levels of cell cycle protein D1 (Cyclin D1) and mRNA levels of cyclin dependent protein kinase 4 (CDK4) in smooth muscle cells were restrained by CD59 and C-PC. CD59 or C-PC alone could inhibit the formation of atherosclerotic plaque by suppressing MMP-2 protein expression. In addition, C-PC could promote CD59 expression. So both CD59 and C-PC could inhibit the progress of atherosclerosis, and the anti-atherosclerotic effects of C-PC might be fulfilled by promoting CD59 expression, preventing smooth muscle cell proliferation and the apoptosis of endothelial cells, reducing blood fat levels, and at last inhibiting the development of atherosclerosis. PMID:24319687

Phenotypic characteristics of upright and pendulous comb among chicken breeds and association with growth rate and egg production.

PubMed

Wan, Yi; Wang, Zhicheng; Guo, Xing; Ma, Chendong; Fang, Qi; Geng, Zhaoyu; Chen, Xingyong; Jiang, Runshen

2018-01-01

Upright and pendulous combs commonly exist in most single-comb chicken breeds. Here, the phenotypic characteristics of upright and pendulous combs in chickens and association with growth rate and egg production were analyzed. Phenotypic frequencies of upright and pendulous comb were investigated in five chicken breeds; the phenotypic frequencies of complete pendulous comb (CPC) and partial pendulous comb (PPC) ranged from 10.1% to 29.0% and 21.8% to 65.3%, respectively. CPC hens produced more eggs than PPC hens (P < 0.05) in Nongda-3, Huainan and Wenchang breeds. In Huainan breed, CPC males were heavier than PPC males at 12 and 16 weeks of age, while CPC females were heavier at 24 weeks of age. PPC and CPC chickens have greater (P < 0.05) comb length, comb height and comb index than upright comb (UC) chickens. There was no significant difference in comb phenotypic frequency distribution between the offspring from UC(♂) × CPC(♀) and CPC(♂) × UC(♀); however, it differed (χ² = 45.12, P < 0.01) between offspring from UC(♂) × UC(♀) and CPC(♂) × CPC(♀). These results suggested that the comb phenotype does not appear to be Z-linked; the effective loci influencing the trait could be estimated in a further study. © 2017 Japanese Society of Animal Science.

Usefulness of image morphing techniques in cancer treatment by conformal radiotherapy

NASA Astrophysics Data System (ADS)

Atoui, Hussein; Sarrut, David; Miguet, Serge

2004-05-01

Conformal radiotherapy is a cancer treatment technique, that targets high-energy X-rays to tumors with minimal exposure to surrounding healthy tissues. Irradiation ballistics is calculated based on an initial 3D Computerized Tomography (CT) scan. At every treatment session, the random positioning of the patient, compared to the reference position defined by the initial 3D CT scan, can generate treatment inaccuracies. Positioning errors potentially predispose to dangerous exposure to healthy tissues as well as insufficient irradiation to the tumor. A proposed solution would be the use of portal images generated by Electronic Portal Imaging Devices (EPID). Portal images (PI) allow a comparison with reference images retained by physicians, namely Digitally Reconstructed Radiographs (DRRs). At present, physicians must estimate patient positional errors by visual inspection. However, this may be inaccurate and consumes time. The automation of this task has been the subject of many researches. Unfortunately, the intensive use of DRRs and the high computing time required have prevented real time implementation. We are currently investigating a new method for DRR generation that calculates intermediate DRRs by 2D deformation of previously computed DRRs. We approach this investigation with the use of a morphing-based technique named mesh warping.

Development of a morphing flap using shape memory alloy actuators: the aerodynamic characteristics of a morphing flap

NASA Astrophysics Data System (ADS)

Ko, Seung-Hee; Bae, Jae-Sung; Rho, Jin-Ho

2014-07-01

The discontinuous contour of a wing with conventional flaps diminishes the aerodynamic performance of an aircraft. A wing with a continuous contour does not experience extreme flow stream fluctuations during flight, and consequently has good aerodynamic characteristics. In this study, a morphing flap using shape memory alloy actuators is proposed, designed and fabricated, and its aerodynamic characteristics are investigated using aerodynamic analyses and wind tunnel tests. The ribs of the morphing flap are designed and fabricated with multiple elements joined together in a way that allows relative rotations of adjacent elements and forms a smooth contour of the morphing flap. The aerodynamic analyses of this multiple-element morphing-flap wing are performed using XFLR pro; its aerodynamic performance is compared with that of a mechanical-flap wing, and is measured through wind-tunnel tests.

Perturbation of Incenp function impedes anaphase chromatid movements and chromosomal passenger protein flux at centromeres

PubMed Central

Ahonen, Leena J.; Kukkonen, Anu M.; Pouwels, Jeroen; Bolton, Margaret A.; Jingle, Christopher D.; Stukenberg, P. Todd; Kallio, Marko J.

2012-01-01

Incenp is an essential mitotic protein that, together with Aurora B, Survivin, and Borealin, forms the core of the chromosomal passenger protein complex (CPC). The CPC regulates various mitotic processes and functions to maintain genomic stability. The proper subcellular localization of the CPC and its full catalytic activity require the presence of each core subunit in the complex. We have investigated the mitotic tasks of the CPC using a function blocking antibody against Incenp microinjected into cells at different mitotic phases. This method allowed temporal analysis of CPC functions without perturbation of complex assembly or activity prior to injection. We have also studied the dynamic properties of Incenp and Aurora B using fusion protein photobleaching. We found that in early mitotic cells, Incenp and Aurora B exhibit dynamic turnover at centromeres, which is prevented by the anti-Incenp antibody. In these cells, the loss of centromeric CPC turnover is accompanied by forced mitotic exit without the execution of cytokinesis. Introduction of anti-Incenp antibody into early anaphase cells causes abnormalities in sister chromatid separation through defects in anaphase spindle functions. In summary, our data uncovers new mitotic roles for the CPC in anaphase and proposes that CPC turnover at centromeres modulates spindle assembly checkpoint signaling. PMID:18784935

Perturbation of Incenp function impedes anaphase chromatid movements and chromosomal passenger protein flux at centromeres.

PubMed

Ahonen, Leena J; Kukkonen, Anu M; Pouwels, Jeroen; Bolton, Margaret A; Jingle, Christopher D; Stukenberg, P Todd; Kallio, Marko J

2009-02-01

Incenp is an essential mitotic protein that, together with Aurora B, Survivin, and Borealin, forms the core of the chromosomal passenger protein complex (CPC). The CPC regulates various mitotic processes and functions to maintain genomic stability. The proper subcellular localization of the CPC and its full catalytic activity require the presence of each core subunit in the complex. We have investigated the mitotic tasks of the CPC using a function blocking antibody against Incenp microinjected into cells at different mitotic phases. This method allowed temporal analysis of CPC functions without perturbation of complex assembly or activity prior to injection. We have also studied the dynamic properties of Incenp and Aurora B using fusion protein photobleaching. We found that in early mitotic cells, Incenp and Aurora B exhibit dynamic turnover at centromeres, which is prevented by the anti-Incenp antibody. In these cells, the loss of centromeric CPC turnover is accompanied by forced mitotic exit without the execution of cytokinesis. Introduction of anti-Incenp antibody into early anaphase cells causes abnormalities in sister chromatid separation through defects in anaphase spindle functions. In summary, our data uncovers new mitotic roles for the CPC in anaphase and proposes that CPC turnover at centromeres modulates spindle assembly checkpoint signaling.

Challenge to the model of lake charr evolution: Shallow- and deep-water morphs exist within a small postglacial lake

USGS Publications Warehouse

Chavarie, Louise; Muir, Andrew M.; Zimmerman, Mara S.; Baillie, Shauna M.; Hansen, Michael J.; Nate, Nancy A.; Yule, Daniel L.; Middel, Trevor; Bentzen, Paul; Krueger, Charles C.

2016-01-01

All examples of lake charr (Salvelinus namaycush) diversity occur within the largest, deepest lakes of North America (i.e. > 2000 km2). We report here Rush Lake (1.3 km2) as the first example of a small lake with two lake charr morphs (lean and huronicus). Morphology, diet, life history, and genetics were examined to demonstrate the existence of morphs and determine the potential influence of evolutionary processes that led to their formation or maintenance. Results showed that the huronicus morph, caught in deep-water, had a deeper body, smaller head and jaws, higher eye position, greater buoyancy, and deeper peduncle than the shallow-water lean morph. Huronicus grew slower to a smaller adult size, and had an older mean age than the lean morph. Genetic comparisons showed low genetic divergence between morphs, indicating incomplete reproductive isolation. Phenotypic plasticity and differences in habitat use between deep and shallow waters associated with variation in foraging opportunities seems to have been sufficient to maintain the two morphs, demonstrating their important roles in resource polymorphism. Rush Lake expands previous explanations for lake charr intraspecific diversity, from large to small lakes and from reproductive isolation to the presence of gene flow associated with strong ecological drivers.

Antinociceptive effect of chlorphenesin carbamate in adjuvant arthritic rats.

PubMed

Okuyama, S; Aihara, H

1987-02-01

The antinociceptive effect of chlorphenesin carbamate (CPC) and mephenesin were examined in adjuvant arthritic rats. In the behavioral study, CPC (100-400 mg/kg, p.o.) but not mephenesin (100-400 mg/kg, p.o.) had a dose-dependent antinociceptive effect, determined using the flexion test. In the electrophysiological study, CPC (25-50 mg/kg, i.v.) but not mephenesin (50 mg/kg, i.v.) depressed the evoked neuronal responses of nociceptive neurons in the ventrobasal thalamus (VB), while the evoked responses of non-nociceptive neurons were not depressed by either CPC (50 mg/kg, i.v.) or mephenesin (50 mg/kg, i.v.). The spontaneous firings of the VB nociceptive neurons were depressed by both CPC (50 mg/kg, i.v.) and mephenesin (50 mg/kg, i.v.). However, mephenesin (50 mg/kg, i.v.) but not CPC (50 mg/kg, i.v.) also depressed the spontaneous firings of the mesencephalic reticular formation (RF), in these adjuvant arthritic rats. These results indicate that CPC but not mephenesin, has an antinociceptive action in adjuvant arthritic rats.

Investigation of the Effect of Mixing Methods and Chemical Treatments on the Conductivity of the CNT/PLA Based Composites

NASA Astrophysics Data System (ADS)

Talwar, Brijpal Singh

The growing popularity of Poly lactic acid (PLA) is mainly due to its biocompatibility, good mechanical properties, and its synthesis from renewable resources. PLA can be compounded with electrically conductive fillers (e.g., carbon nanotubes (CNTs)) to form conductive polymer composites (CPCs). These fillers provide conductive functionality to the composite material by forming percolation paths. Featuring very low weight densities, CPCs have the potential to replace metals in the electronic industry, if they exhibit similar electrical conductivities to that of the metals. The current challenges being faced during the mixing of CNTs in the polymer matrix are: formation of aggregates due to strong van der Waals forces and breakage of CNTs during dispersion. In this study, we compare: (1) two fabrication methods to create CPCs (i.e., solution mixing by sonication and melt extrusion) (2) effect of various CNT functionalization techniques (i.e., acid and plasma treatments) on the conductivity of CPCs and (3) effect of using binding molecules like para-phenylenediamine, that act as bridges in between the CNTs in the CPCs and its effect on the conductivity of CPCs. Such conductive composite materials find widespread technological applications which either require, or could benefit from, the ability to pattern micro-sized features in two-dimensional (2D) and three-dimensional (3D) architectures. Direct-write fabrication technique is used to realise these printed patterns, using the CPC solution as ink. First, the composites comprising of 30% PLA by weight in Dichloromethane (DCM) and CNTs in different concentrations (up to 5wt. %) are fabricated using a two-step sonication method (i.e., dissolving PLA in DCM and then dispersing the CNTs in this polymer solution). Second, CPCs are fabricated using a twin screw micro extruder operating at 180°C. To verify the effects of functionalization of the CNTs on the conductivity of composites, the CNTs are functionalized by three methods: HNO3 acid functionalization, 3:1 ratio HNO 3 + H2SO4 acid (stronger) functionalization and N2 plasma functionalization. To check the effect of amine binding molecules, HNO3 acid functionalized CNTs are treated with a mixture of para-phenylenediamine and aniline in an acidic solution. These chemically treated CNTs are then mixed with PLA to form composites. CPC fibers are drawn using the solvent-cast printing method. These fibers are tested for their electrical conductivity using the two-probe resistivity measurement method. Maximum electrical conductivity was observed in the 5wt. % CNT concentration samples at 3.97 S/m and 25.16 S/m for CPC fibers obtained via the solution blend and the extrusion methods, respectively. In the case of the functionalized CNTs, conductivity measurements show a negative effect of functionalization on the electrical properties of the CPC. While, the amine treated CNT/PLA CPC fibers show better conductivity at 4.2 S/m when compared to the untreated CNT/PLA samples manufactured using the solution mixing method. Finally, one-dimensional (1D) structures like fibres and 2D, 3D structures like single and multi-layer scaffolds were fabricated using the solvent-cast printing technique with the above manufactured CPC solutions in DCM as inks. Such conductive microstructures find their application in the electronic industry and in micro-scale systems such as pollution detection in natural environments, tissue engineering, mechanical sensors and smart devices.

Fraudulent ID using face morphs: Experiments on human and automatic recognition

PubMed Central

Robertson, David J.; Kramer, Robin S. S.

2017-01-01

Matching unfamiliar faces is known to be difficult, and this can give an opportunity to those engaged in identity fraud. Here we examine a relatively new form of fraud, the use of photo-ID containing a graphical morph between two faces. Such a document may look sufficiently like two people to serve as ID for both. We present two experiments with human viewers, and a third with a smartphone face recognition system. In Experiment 1, viewers were asked to match pairs of faces, without being warned that one of the pair could be a morph. They very commonly accepted a morphed face as a match. However, in Experiment 2, following very short training on morph detection, their acceptance rate fell considerably. Nevertheless, there remained large individual differences in people’s ability to detect a morph. In Experiment 3 we show that a smartphone makes errors at a similar rate to ‘trained’ human viewers—i.e. accepting a small number of morphs as genuine ID. We discuss these results in reference to the use of face photos for security. PMID:28328928

Fraudulent ID using face morphs: Experiments on human and automatic recognition.

PubMed

Robertson, David J; Kramer, Robin S S; Burton, A Mike

2017-01-01

Matching unfamiliar faces is known to be difficult, and this can give an opportunity to those engaged in identity fraud. Here we examine a relatively new form of fraud, the use of photo-ID containing a graphical morph between two faces. Such a document may look sufficiently like two people to serve as ID for both. We present two experiments with human viewers, and a third with a smartphone face recognition system. In Experiment 1, viewers were asked to match pairs of faces, without being warned that one of the pair could be a morph. They very commonly accepted a morphed face as a match. However, in Experiment 2, following very short training on morph detection, their acceptance rate fell considerably. Nevertheless, there remained large individual differences in people's ability to detect a morph. In Experiment 3 we show that a smartphone makes errors at a similar rate to 'trained' human viewers-i.e. accepting a small number of morphs as genuine ID. We discuss these results in reference to the use of face photos for security.

Is the chiasm-pituitary corridor size important for achieving gross-total resection during endonasal endoscopic resection of craniopharyngiomas?

PubMed

Omay, Sacit Bulent; Almeida, João Paulo; Chen, Yu-Ning; Shetty, Sathwik R; Liang, Buqing; Ni, Shilei; Anand, Vijay K; Schwartz, Theodore H

2017-11-24

OBJECTIVE Craniopharyngiomas arise from the pituitary stalk, and in adults they are generally located posterior to the chiasm extending up into the third ventricle. The extended endonasal approach (EEA) can provide an ideal corridor between the bottom of the optic chiasm and the top of the pituitary gland (chiasm-pituitary corridor [CPC]) for their removal. A narrow CPC in patients with a prefixed chiasm and a large tumor extending up and behind the chiasm has been considered a contraindication to EEA, with a high risk of visual deterioration and subtotal resection. METHODS A database of all patients treated in the authors' center (Weill Cornell Medical College, NewYork-Presbyterian Hospital) between July 2004 and August 2016 was reviewed. Patients with craniopharyngiomas who underwent EEA with the goal of gross-total resection (GTR) were included in the study. Patients with postfixed chiasm or limited available preoperative imaging were excluded. Using preoperative contrast-enhanced T1-weighted sagittal midline MR images, the authors calculated the CPC as well as the distance from the chiasm to the top of the tumor (CTOT). From these numbers, they calculated a ratio of the CPC to the CTOT as a measure of difficulty in removing the tumors through the EEA and called this ratio the corridor index (CI). The relationship between the CI and the ability to achieve GTR and visual outcome were measured. RESULTS Thirty-four patients were included in the study. The mean CPC was 10.1 mm (range 5.2-19.1 mm). The mean CTOT was 12.8 mm (range 0-28.3 mm). The median CI was 0.8; the CI ranged from 0.4 to infinity (for tumors with a CTOT of 0). Thirty-two patients had GTR (94.1%) and 2 had subtotal resection. The CPC value had no relationship with our ability to achieve GTR and no effect on visual or endocrine outcome. CONCLUSIONS EEA for craniopharyngioma is generally considered the first-line surgical approach. Although a narrow corridor between the top of the pituitary gland and the bottom of the chiasm may seem to be a relative contraindication to surgery for larger tumors, the authors' data do not bear this out. EEA appears to be a successful technique for the majority of midline craniopharyngiomas.

Design Methods and Optimization for Morphing Aircraft

NASA Technical Reports Server (NTRS)

Crossley, William A.

2005-01-01

This report provides a summary of accomplishments made during this research effort. The major accomplishments are in three areas. The first is the use of a multiobjective optimization strategy to help identify potential morphing features that uses an existing aircraft sizing code to predict the weight, size and performance of several fixed-geometry aircraft that are Pareto-optimal based upon on two competing aircraft performance objectives. The second area has been titled morphing as an independent variable and formulates the sizing of a morphing aircraft as an optimization problem in which the amount of geometric morphing for various aircraft parameters are included as design variables. This second effort consumed most of the overall effort on the project. The third area involved a more detailed sizing study of a commercial transport aircraft that would incorporate a morphing wing to possibly enable transatlantic point-to-point passenger service.

Shape Sensing a Morphed Wing with an Optical Fiber Bragg Grating

NASA Technical Reports Server (NTRS)

Tai, Hsiang

2005-01-01

We suggest using distributed fiber Bragg sensors systems which were developed locally at Langley Research Center carefully placed on the wing surface to collect strain component information at each location. Then we used the fact that the rate change of slope in the definition of linear strain is very small and can be treated as a constant. Thereby the strain distribution information of a morphed surface can be reduced into a distribution of local slope information of a flat surface. In other words a morphed curve surface is replaced by the collection of individual flat surface of different slope. By assembling the height of individual flat surface, the morphed curved surface can be approximated. A more sophisticated graphic routine can be utilized to restore the curved morphed surface. With this information, the morphed wing can be further adjusted and controlled. A numerical demonstration is presented.

Centrifugal partition chromatography in a biorefinery context: Separation of monosaccharides from hydrolysed sugar beet pulp.

PubMed

Ward, David P; Cárdenas-Fernández, Max; Hewitson, Peter; Ignatova, Svetlana; Lye, Gary J

2015-09-11

A critical step in the bioprocessing of sustainable biomass feedstocks, such as sugar beet pulp (SBP), is the isolation of the component sugars from the hydrolysed polysaccharides. This facilitates their subsequent conversion into higher value chemicals and pharmaceutical intermediates. Separation methodologies such as centrifugal partition chromatography (CPC) offer an alternative to traditional resin-based chromatographic techniques for multicomponent sugar separations. Highly polar two-phase systems containing ethanol and aqueous ammonium sulphate are examined here for the separation of monosaccharides present in hydrolysed SBP pectin: l-rhamnose, l-arabinose, d-galactose and d-galacturonic acid. Dimethyl sulfoxide (DMSO) was selected as an effective phase system modifier improving monosaccharide separation. The best phase system identified was ethanol:DMSO:aqueous ammonium sulphate (300gL(-1)) (0.8:0.1:1.8, v:v:v) which enabled separation of the SBP monosaccharides by CPC (200mL column) in ascending mode (upper phase as mobile phase) with a mobile phase flow rate of 8mLmin(-1). A mixture containing all four monosaccharides (1.08g total sugars) in the proportions found in hydrolysed SBP was separated into three main fractions; a pure l-rhamnose fraction (>90%), a mixed l-arabinose/d-galactose fraction and a pure d-galacturonic acid fraction (>90%). The separation took less than 2h demonstrating that CPC is a promising technique for the separation of these sugars with potential for application within an integrated, whole crop biorefinery. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

High-Fidelity Aerostructural Design Optimization of Transport Aircraft with Continuous Morphing Trailing Edge Technology

NASA Astrophysics Data System (ADS)

Burdette, David A., Jr.

Adaptive morphing trailing edge technology offers the potential to decrease the fuel burn of transonic commercial transport aircraft by allowing wings to dynamically adjust to changing flight conditions. Current configurations allow flap and aileron droop; however, this approach provides limited degrees of freedom and increased drag produced by gaps in the wing's surface. Leading members in the aeronautics community including NASA, AFRL, Boeing, and a number of academic institutions have extensively researched morphing technology for its potential to improve aircraft efficiency. With modern computational tools it is possible to accurately and efficiently model aircraft configurations in order to quantify the efficiency improvements offered by mor- phing technology. Coupled high-fidelity aerodynamic and structural solvers provide the capability to model and thoroughly understand the nuanced trade-offs involved in aircraft design. This capability is important for a detailed study of the capabilities of morphing trailing edge technology. Gradient-based multidisciplinary design opti- mization provides the ability to efficiently traverse design spaces and optimize the trade-offs associated with the design. This thesis presents a number of optimization studies comparing optimized config- urations with and without morphing trailing edge devices. The baseline configuration used throughout this work is the NASA Common Research Model. The first opti- mization comparison considers the optimal fuel burn predicted by the Breguet range equation at a single cruise point. This initial singlepoint optimization comparison demonstrated a limited fuel burn savings of less than 1%. Given the effectiveness of the passive aeroelastic tailoring in the optimized non-morphing wing, the singlepoint optimization offered limited potential for morphing technology to provide any bene- fit. To provide a more appropriate comparison, a number of multipoint optimizations were performed. With a 3-point stencil, the morphing wing burned 2.53% less fuel than its optimized non-morphing counterpart. Expanding further to a 7-point stencil, the morphing wing used 5.04% less fuel. Additional studies demonstrate that the size of the morphing device can be reduced without sizable performance reductions, and that as aircraft wings' aspect ratios increase, the effectiveness of morphing trailing edge devices increases. The final set of studies in this thesis consider mission analy- sis, including climb, multi-altitude cruise, and descent. These mission analyses were performed with a number of surrogate models, trained with O(100) optimizations. These optimizations demonstrated fuel burn reductions as large as 5% at off-design conditions. The fuel burn predicted by the mission analysis was up to 2.7% lower for the morphing wing compared to the conventional configuration.

Acoustic characteristics used by Japanese macaques for individual discrimination.

PubMed

Furuyama, Takafumi; Kobayasi, Kohta I; Riquimaroux, Hiroshi

2017-10-01

The vocalizations of primates contain information about speaker individuality. Many primates, including humans, are able to distinguish conspecifics based solely on vocalizations. The purpose of this study was to investigate the acoustic characteristics used by Japanese macaques in individual vocal discrimination. Furthermore, we tested human subjects using monkey vocalizations to evaluate species specificity with respect to such discriminations. Two monkeys and five humans were trained to discriminate the coo calls of two unfamiliar monkeys. We created a stimulus continuum between the vocalizations of the two monkeys as a set of probe stimuli (whole morph). We also created two sets of continua in which only one acoustic parameter, fundamental frequency ( f 0 ) or vocal tract characteristic (VTC), was changed from the coo call of one monkey to that of another while the other acoustic feature remained the same ( f 0 morph and VTC morph, respectively). According to the results, the reaction times both of monkeys and humans were correlated with the morph proportion under the whole morph and f 0 morph conditions. The reaction time to the VTC morph was correlated with the morph proportion in both monkeys, whereas the reaction time in humans, on average, was not correlated with morph proportion. Japanese monkeys relied more consistently on VTC than did humans for discriminating monkey vocalizations. Our results support the idea that the auditory system of primates is specialized for processing conspecific vocalizations and suggest that VTC is a significant acoustic feature used by Japanese macaques to discriminate conspecific vocalizations. © 2017. Published by The Company of Biologists Ltd.

Survival of timber rattlesnakes (Crotalus horridus) estimated by capture-recapture models in relation to age, sex, color morph, time, and birthplace

USGS Publications Warehouse

Brown, W.S.; Kery, M.; Hines, J.E.

2007-01-01

Juvenile survival is one of the least known elements of the life history of many species, in particular snakes. We conducted a mark–recapture study of Crotalus horridus from 1978–2002 in northeastern New York near the northern limits of the species' range. We marked 588 neonates and estimated annual age-, sex-, and morph-specific recapture and survival rates using the Cormack-Jolly-Seber (CJS) model. Wild-caught neonates (field-born, n  =  407) and neonates produced by captive-held gravid females (lab-born, n  =  181) allowed comparison of the birthplace, or lab treatment effect, in estimated survival. Recapture rates declined from about 10–20% over time while increasing from young to older age classes. Estimated survival rates (S ± 1 SE) in the first year were significantly higher among field-born (black morph: S  =  0.773 ± 0.203; yellow morph: S  =  0.531 ± 0.104) than among lab-born snakes (black morph: S  =  0.411 ± 0.131; yellow morph: S  =  0.301 ± 0.081). Lower birth weights combined with a lack of field exposure until release apparently contributed to the lower survival rate of lab-born snakes. Subsequent survival estimates for 2–4-yr-old snakes were S  =  0.845 ± 0.084 for the black morph and S  =  0.999 (SE not available) for the yellow morph, and for ≥5-yr-old snakes S  =  0.958 ± 0.039 (black morph) and S  =  0.822 ± 0.034 (yellow morph). The most parsimonious model overall contained an independent time trend for survival of each age, morph, and lab-treatment group. For snakes of the first two age groups (ages 1 yr and 2–4 yr), survival tended to decline over the years for both morphs, while for adult snakes (5 yr and older), survival was constant or even slightly increased. Our data on survival and recapture are among the first rigorous estimates of these parameters in a rattlesnake and among the few yet available for any viperid snake. These data are useful for analyses of the life-history strategy, population dynamics, and conservation of this long-lived snake.

Engineering Isoprene Synthase Expression and Activity in Cyanobacteria.

PubMed

Chaves, Julie E; Rueda-Romero, Paloma; Kirst, Henning; Melis, Anastasios

2017-12-15

Efforts to heterologously produce quantities of isoprene hydrocarbons (C 5 H 8 ) renewably from CO 2 and H 2 O through the photosynthesis of cyanobacteria face barriers, including low levels of recombinant enzyme accumulation compounded by their slow innate catalytic activity. The present work sought to alleviate the "expression level" barrier upon placing the isoprene synthase (IspS) enzyme in different fusion configurations with the cpcB protein, the highly expressed β-subunit of phycocyanin. Different cpcB*IspS fusion constructs were made, distinguished by the absence or presence of linker amino acids between the two proteins. Composition of linker amino acids was variable with lengths of 7, 10, 16, and 65 amino acids designed to test for optimal activity of the IspS through spatial positioning between the cpcB and IspS. Results showed that fusion constructs with the highly expressed cpcB gene, as the leader sequence, improved transgene expression in the range of 61 to 275-fold over what was measured with the unfused IspS control. However, the specific activity of the IspS enzyme was attenuated in all fusion transformants, possibly because of allosteric effects exerted by the leader cpcB fusion protein. This inhibition varied depending on the nature of the linker amino acids between the cpcB and IspS proteins. In terms of isoprene production, the results further showed a trade-off between specific activity and transgenic enzyme accumulation. For example, the cpcB*L7*IspS strain showed only about 10% the isoprene synthase specific-activity of the unfused cpcB-IspS control, but it accumulated 254-fold more IspS enzyme. The latter more than countered the slower specific activity and made the cpcB*L7*IspS transformant the best isoprene producing strain in this work. Isoprene to biomass yield ratios improved from 0.2 mg g -1 in the unfused cpcB-IspS control to 5.4 mg g -1 in the cpcB*L7*IspS strain, a 27-fold improvement.

Island biology and morphological divergence of the Skyros wall lizard Podarcis gaigeae: a combined role for local selection and genetic drift on color morph frequency divergence?

PubMed Central

2010-01-01

Background Patterns of spatial variation in discrete phenotypic traits can be used to draw inferences about the adaptive significance of traits and evolutionary processes, especially when compared to patterns of neutral genetic variation. Population divergence in adaptive traits such as color morphs can be influenced by both local ecology and stochastic factors such as genetic drift or founder events. Here, we use quantitative color measurements of males and females of Skyros wall lizard, Podarcis gaigeae, to demonstrate that this species is polymorphic with respect to throat color, and the morphs form discrete phenotypic clusters with limited overlap between categories. We use divergence in throat color morph frequencies and compare that to neutral genetic variation to infer the evolutionary processes acting on islet- and mainland populations. Results Geographically close islet- and mainland populations of the Skyros wall lizard exhibit strong divergence in throat color morph frequencies. Population variation in throat color morph frequencies between islets was higher than that between mainland populations, and the effective population sizes on the islets were small (Ne:s < 100). Population divergence (FST) for throat color morph frequencies fell within the neutral FST-distribution estimated from microsatellite markers, and genetic drift could thus not be rejected as an explanation for the pattern. Moreover, for both comparisons among mainland-mainland population pairs and between mainland-islet population pairs, morph frequency divergence was significantly correlated with neutral divergence, further pointing to some role for genetic drift in divergence also at the phenotypic level of throat color morphs. Conclusions Genetic drift could not be rejected as an explanation for the pattern of population divergence in morph frequencies. In spite of an expected stabilising selection, throat color frequencies diverged in the islet populations. These results suggest that there is an interaction between selection and genetic drift causing divergence even at a phenotypic level in these small, subdivided populations. PMID:20813033

Improving bone repair of femoral and radial defects in rabbit by incorporating PRP into PLGA/CPC composite scaffold with unidirectional pore structure.

PubMed

He, Fupo; Chen, Yan; Li, Jiyan; Lin, Bomiao; Ouyang, Yi; Yu, Bo; Xia, Yuanyou; Yu, Bo; Ye, Jiandong

2015-04-01

In this study, a platelet-rich plasma poly(lactic-co-glycolic acid) (PRP-PLGA)/calcium phosphate cement (CPC) composite scaffold was prepared by incorporating PRP into PLGA/CPC scaffold with unidirectional pore structure, which was fabricated by the unidirectional freeze casting of CPC slurry and the following infiltration of PLGA. The results from in vitro cell experiments and in vivo implantation in femoral defects manifested that incorporation of PRP into PLGA/CPC scaffold improved in vitro cell response (cell attachment, proliferation, and differentiation), and markedly boosted bone formation, angiogenesis and material degradation. The incorporation of PRP into scaffold showed more outstanding improvement in osteogenesis as the scaffolds were used to repair the segmental radial defects, especially at the early stage. The new bone tissues grew along the unidirectional lamellar pores of scaffold. At 12 weeks postimplantation, the segmental radial defects treated with PRP-PLGA/CPC scaffold had almost recuperated, whereas treated with the scaffold without PRP was far from healed. Taken together, the PRP-PLGA/CPC scaffold with unidirectional pore structure is a promising candidate to repair bone defects at various sites. © 2014 Wiley Periodicals, Inc.

De novo Sequencing and Comparative Transcriptomics of Floral Development of the Distylous Species Lithospermum multiflorum

PubMed Central

Cohen, James I.

2016-01-01

Genes controlling the morphological, micromorphological, and physiological components of the breeding system distyly have been hypothesized, but many of the genes have not been investigated throughout development of the two floral morphs. To this end, the present study is an examination of comparative transcriptomes from three stages of development for the floral organs of the morphs of Lithospermum multiflorum. Transcriptomes of flowers of the two morphs, from various stages of development, were sequenced using an Illumina HiSeq 2000. The floral transcriptome of L. multiflorum was assembled, and differential gene expression (DE) was identified between morphs, throughout development. Additionally, Gene Ontology (GO) terms for DE genes were determined. Fewer genes were DE early in development compared to later in development, with more genes highly expressed in the gynoecium of the SS morph and the corolla and androecium of the LS morph. A reciprocal pattern was observed later in development, and many more genes were DE during this latter stage. During early development, DE genes appear to be involved in growth and floral development, and during later development, DE genes seem to affect physiological functions. Interestingly, many genes involved in response to stress were identified as DE between morphs. PMID:28066486

De novo Sequencing and Comparative Transcriptomics of Floral Development of the Distylous Species Lithospermum multiflorum.

PubMed

Cohen, James I

2016-01-01

Genes controlling the morphological, micromorphological, and physiological components of the breeding system distyly have been hypothesized, but many of the genes have not been investigated throughout development of the two floral morphs. To this end, the present study is an examination of comparative transcriptomes from three stages of development for the floral organs of the morphs of Lithospermum multiflorum . Transcriptomes of flowers of the two morphs, from various stages of development, were sequenced using an Illumina HiSeq 2000. The floral transcriptome of L. multiflorum was assembled, and differential gene expression (DE) was identified between morphs, throughout development. Additionally, Gene Ontology (GO) terms for DE genes were determined. Fewer genes were DE early in development compared to later in development, with more genes highly expressed in the gynoecium of the SS morph and the corolla and androecium of the LS morph. A reciprocal pattern was observed later in development, and many more genes were DE during this latter stage. During early development, DE genes appear to be involved in growth and floral development, and during later development, DE genes seem to affect physiological functions. Interestingly, many genes involved in response to stress were identified as DE between morphs.

Parasites and parallel divergence of the number of individual MHC alleles between sympatric three-spined stickleback Gasterosteus aculeatus morphs in Iceland.

PubMed

Natsopoulou, M E; Pálsson, S; Ólafsdóttir, G Á

2012-10-01

Two pairs of sympatric three-spined stickleback Gasterosteus aculeatus morphs and two single morph populations inhabiting mud and lava or rocky benthic habitats in four Icelandic lakes were screened for parasites and genotyped for MHC class IIB diversity. Parasitic infection differed consistently between G. aculeatus from different benthic habitats. Gasterosteus aculeatus from the lava or rocky habitats were more heavily infected in all lakes. A parallel pattern was also found in individual MHC allelic variation with lava G. aculeatus morphs exhibiting lower levels of variation than the mud morphs. Evidence for selective divergence in MHC allele number is ambiguous but supported by two findings in addition to the parallel pattern observed. MHC allele diversity was not consistent with diversity reported at neutral markers (microsatellites) and in Þingvallavatn the most common number of alleles in each morph was associated with lower infection levels. In the Þingvallavatn lava morph, lower infection levels by the two most common parasites, Schistocephalus solidus and Diplostomum baeri, were associated with different MHC allele numbers. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Gram-scale purification of aconitine and identification of lappaconitine in Aconitum karacolicum.

PubMed

Tarbe, M; de Pomyers, H; Mugnier, L; Bertin, D; Ibragimov, T; Gigmes, D; Mabrouk, K

2017-07-01

Aconitum karacolicum from northern Kyrgyzstan (Alatau area) contains about 0.8-1% aconitine as well as other aconite derivatives that have already been identified. In this paper, we compare several methods for the further purification of an Aconitum karacolicum extract initially containing 80% of aconitine. Reverse-phase flash chromatography, reverse-phase semi-preparative HPLC, centrifugal partition chromatography (CPC) and recrystallization techniques were evaluated regarding first their efficiency to get the highest purity of aconitine (over 96%) and secondly their applicability in a semi-industrial scale purification process (in our case, 150g of plant extract). Even if the CPC technique shows the highest purification yield (63%), the recrystallization remains the method of choice to purify a large amount of aconitine as i) it can be easily carried out in safe conditions; ii) an aprotic solvent is used, avoiding aconitine degradation. Moreover, this study led us to the identification of lappaconitine in Aconitum karacolicum, a well-known alkaloid never found in this Aconitum species. Copyright © 2017 Elsevier B.V. All rights reserved.

Active-Vision Control Systems for Complex Adversarial 3-D Environments

DTIC Science & Technology

2009-03-01

Control Systems MURI Final Report 36 51. D. Nain, S. Haker , A. Bobick, A. Tannenbaum, "Multiscale 3D shape representation and segmentation using...Conference, August 2008. 99. L. Zhu, Y. Yang, S. Haker , and A. Tannenbaum, "An image morphing technique based on optimal mass preserving mapping," IEEE

Social Inferences from Faces: Ambient Images Generate a Three-Dimensional Model

ERIC Educational Resources Information Center

Sutherland, Clare A. M.; Oldmeadow, Julian A.; Santos, Isabel M.; Towler, John; Burt, D. Michael; Young, Andrew W.

2013-01-01

Three experiments are presented that investigate the two-dimensional valence/trustworthiness by dominance model of social inferences from faces (Oosterhof & Todorov, 2008). Experiment 1 used image averaging and morphing techniques to demonstrate that consistent facial cues subserve a range of social inferences, even in a highly variable sample of…

Protecting quantum memories using coherent parity check codes

NASA Astrophysics Data System (ADS)

Roffe, Joschka; Headley, David; Chancellor, Nicholas; Horsman, Dominic; Kendon, Viv

2018-07-01

Coherent parity check (CPC) codes are a new framework for the construction of quantum error correction codes that encode multiple qubits per logical block. CPC codes have a canonical structure involving successive rounds of bit and phase parity checks, supplemented by cross-checks to fix the code distance. In this paper, we provide a detailed introduction to CPC codes using conventional quantum circuit notation. We demonstrate the implementation of a CPC code on real hardware, by designing a [[4, 2, 2

Recent Results from NASA's Morphing Project

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria R.; Washburn, Anthony E.; Horta, Lucas G.; Bryant, Robert G.; Cox, David E.; Siochi, Emilie J.; Padula, Sharon L.; Holloway, Nancy M.

2002-01-01

The NASA Morphing Project seeks to develop and assess advanced technologies and integrated component concepts to enable efficient, multi-point adaptability in air and space vehicles. In the context of the project, the word "morphing" is defined as "efficient, multi-point adaptability" and may include macro, micro, structural and/or fluidic approaches. The project includes research on smart materials, adaptive structures, micro flow control, biomimetic concepts, optimization and controls. This paper presents an updated overview of the content of the Morphing Project including highlights of recent research results.

Effect of Ultrasonic Extraction on Production and Structural Changes of C-Phycocyanin from Marine Spirulina maxima.

PubMed

Choi, Woon Yong; Lee, Hyeon Yong

2018-01-11

This work first showed that very high amounts of phycocyanins, such as 11.3 mg/mL C-phycocyanin (C-PC), 3.1 mg/mL allophycocyanin (APC), and 0.8 mg/mL phycoerythrin (PE), can be obtained using an ultrasonic extraction process (UE) with a 60 kHz frequency and 3 h of process time at 25 °C, without any other pretreatments. These yields were higher than those from most conventional water extractions at 4 °C for 24 h (Control condition) or at 25 °C for 24 h (WE), namely, 9.8 and 5.7 mg/mL C-PC, 2.3 and 1.2 mg/mL APC, and 0.7 and 0.3 mg/mL PE, respectively. These yields were also shown to be even higher than yields from other reported data. Structural changes in C-PC in the extracts were also found for the first time, according to extraction conditions, showing that the total concentration of C-PC and of the α-subunit of C-PC in the UE were much higher than in the WE, with little difference in the amount of β-subunit of C-PC in the UE or WE. It was also shown that the structural changes in C-PC in the WE decreased both antioxidant and anti-inflammation activities-29.83% vs. 32.09% of α,α-diphenyl-β-picrylhydrazyl (DPPH) scavenging activity and 8.21 vs. 7.25 µM of NO production for the WE and UE, respectively-while the UE, with similar patterns to standard C-PC, showed very high biological effects, which may suggest that the biologically active part is the α-subunit of C-PC, not the β-subunit.

Effect of Ultrasonic Extraction on Production and Structural Changes of C-Phycocyanin from Marine Spirulina maxima

PubMed Central

Choi, Woon Yong; Lee, Hyeon Yong

2018-01-01

This work first showed that very high amounts of phycocyanins, such as 11.3 mg/mL C-phycocyanin (C-PC), 3.1 mg/mL allophycocyanin (APC), and 0.8 mg/mL phycoerythrin (PE), can be obtained using an ultrasonic extraction process (UE) with a 60 kHz frequency and 3 h of process time at 25 °C, without any other pretreatments. These yields were higher than those from most conventional water extractions at 4 °C for 24 h (Control condition) or at 25 °C for 24 h (WE), namely, 9.8 and 5.7 mg/mL C-PC, 2.3 and 1.2 mg/mL APC, and 0.7 and 0.3 mg/mL PE, respectively. These yields were also shown to be even higher than yields from other reported data. Structural changes in C-PC in the extracts were also found for the first time, according to extraction conditions, showing that the total concentration of C-PC and of the α-subunit of C-PC in the UE were much higher than in the WE, with little difference in the amount of β-subunit of C-PC in the UE or WE. It was also shown that the structural changes in C-PC in the WE decreased both antioxidant and anti-inflammation activities—29.83% vs. 32.09% of α,α-diphenyl-β-picrylhydrazyl (DPPH) scavenging activity and 8.21 vs. 7.25 µM of NO production for the WE and UE, respectively—while the UE, with similar patterns to standard C-PC, showed very high biological effects, which may suggest that the biologically active part is the α-subunit of C-PC, not the β-subunit. PMID:29324668

UNUSUAL PHENOLIC COMPOUNDS CONTRIBUTE TO ECOPHYSIOLOGICAL PERFORMANCE IN THE PURPLE-COLORED GREEN ALGA ZYGOGONIUM ERICETORUM (ZYGNEMATOPHYCEAE, STREPTOPHYTA) FROM A HIGH-ALPINE HABITAT

PubMed Central

Aigner, Siegfried; Remias, Daniel; Karsten, Ulf; Holzinger, Andreas

2013-01-01

The filamentous green alga Zygogonium ericetorum (Zygnematophyceae, Streptophyta) was collected in a high-alpine rivulet in Tyrol, Austria. Two different morphotypes of this alga were found: a purple morph with a visible purple vacuolar content and a green morph lacking this coloration. These morphotypes were compared with respect to their secondary metabolites, ultrastructure, and ecophysiological properties. Colorimetric tests with aqueous extracts of the purple morph indicated the presence of soluble compounds such as phenolics and hydrolyzable tannins. High-performance liquid chromatography-screening showed that Z. ericetorum contained several large phenolic peaks with absorption maxima at ∼280 nm and sometimes with minor maxima at ∼380 nm. Such compounds are uncommon for freshwater green microalgae, and could contribute to protect the organism against increased UV and visible (VIS) irradiation. The purple Z. ericetorum contained larger amounts (per dry weight) of the putative phenolic substances than the green morph; exposure to irradiation may be a key factor for accumulation of these phenolic compounds. Transmission electron microscopy of the purple morph showed massive vacuolization with homogenous medium electron-dense content in the cell periphery, which possibly contains the secondary compounds. In contrast, the green morph had smaller, electron-translucent vacuoles. The ecophysiological data on photosynthesis and desiccation tolerance indicated that increasing photon fluence densities led to much higher relative electron transport rates (rETR) in the purple than in the green morph. These data suggest that the secondary metabolites in the purple morph are important for light acclimation in high-alpine habitats. However, the green morph recovered better after 4 d of rehydration following desiccation stress. PMID:25810559

The colour of paternity: extra-pair paternity in the wild Gouldian finch does not appear to be driven by genetic incompatibility between morphs.

PubMed

Bolton, P E; Rollins, L A; Brazill-Boast, J; Kim, K-W; Burke, T; Griffith, S C

2017-01-01

In socially monogamous species, individuals can use extra-pair paternity and offspring sex allocation as adaptive strategies to ameliorate costs of genetic incompatibility with their partner. Previous studies on domesticated Gouldian finches (Erythrura gouldiae) demonstrated a genetic incompatibility between head colour morphs, the effects of which are more severe in female offspring. Domesticated females use differential sex allocation, and extra-pair paternity with males of compatible head colour, to reduce fitness costs associated with incompatibility in mixed-morph pairings. However, laboratory studies are an oversimplification of the complex ecological factors experienced in the wild and may only reflect the biology of a domesticated species. This study aimed to examine the patterns of parentage and sex ratio bias with respect to colour pairing combinations in a wild population of the Gouldian finch. We utilized a novel PCR assay that allowed us to genotype the morph of offspring before the morph phenotype develops and to explore bias in morph paternity and selection at the nest. Contrary to previous findings in the laboratory, we found no effect of pairing combinations on patterns of extra-pair paternity, offspring sex ratio or selection on morphs in nestlings. In the wild, the effect of morph incompatibility is likely much smaller, or absent, than was observed in the domesticated birds. Furthermore, the previously studied domesticated population is genetically differentiated from the wild population, consistent with the effects of domestication. It is possible that the domestication process fostered the emergence (or enhancement) of incompatibility between colour morphs previously demonstrated in the laboratory. © 2016 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2016 European Society For Evolutionary Biology.

The endocrine-genetic basis of life-history variation: the relationship between the ecdysteroid titer and morph-specific reproduction in the wing-polymorphic cricket Gryllus firmus.

PubMed

Zera, A J; Bottsford, J

2001-03-01

The hormonal basis of variation in life-history traits is a poorly studied topic in life-history evolution. An important step in identifying the endocrine-genetic causes of life-history variation is documenting statistical and functional associations between hormone titers and genotypes/phenotypes that vary in life-history traits. To this end, we compared the blood ecdysteroid titer and the mass of the ovaries during the first week of adulthood among a flight-capable morph and two flightless morphs of the wing-polymorphic cricket Gryllus firmus. Ecdysteroids are a group of structurally related hormones that regulate many important aspects of reproduction in insects. Both the ecdysteroid titer and ovarian mass were significantly higher in each of two flightless morphs compared with the flight-capable morph throughout the first week of adulthood. Genetically based differences in the ecdysteroid titer and ovarian mass between morphs from different selected lines were similar to phenotypically based differences among morphs from the same control (unselected) lines. By day 7 of adulthood, ovaries were typically 200-400% larger and the ecdysteroid titer was 60-300% higher in flightless versus the flight-capable morph. In addition, highly significant, positive, phenotypic correlations were observed between the ecdysteroid titer and ovarian mass in pooled samples of the two flightless and flight-capable crickets from control lines or from selected lines. The ecdysteroid titer was sufficiently elevated in the flightless morphs to account for their elevated ovarian growth. This is the first direct documentation that naturally occurring phenotypes/genotypes that differ in early fecundity, a key life-history trait, also differ phenotypically and genetically in the titer of a key reproductive hormone that potentially regulates that trait.

Multiple exaggerated weapon morphs: a novel form of male polymorphism in harvestmen.

PubMed

Painting, Christina J; Probert, Anna F; Townsend, Daniel J; Holwell, Gregory I

2015-11-06

Alternative reproductive tactics in animals are commonly associated with distinct male phenotypes resulting in polymorphism of sexually selected weapons such as horns and spines. Typically, morphs are divided between small (unarmed) and large (armed) males according to one or more developmental thresholds in association with body size. Here, we describe remarkable weapon trimorphism within a single species, where two exaggerated weapon morphs and a third morph with reduced weaponry are present. Male Pantopsalis cheliferoides harvestmen display exaggerated chelicerae (jaws) which are highly variable in length among individuals. Across the same body size spectrum, however, some males belong to a distinct second exaggerated morph which possesses short, broad chelicerae. Multiple weapon morphs in a single species is a previously unknown phenomenon and our findings have significant implications for understanding weapon diversity and maintenance of polymorphism. Specifically, this species will be a valuable model for testing how weapons diverge by being able to test directly for the circumstances under which a certain weapon type is favoured and how weapon shape relates to performance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, R.H.

A three-year field study was conducted in Illinois to investigate seasonal, annual and geographic variation in color morph proportions of the cricket frog, Acris crepitans. Life history information (i.e., time of overwintering, emergence of adults in spring, breeding, metamorphosis, emergence of juveniles in summer, and growth and survival) for A. crepitans color morphs was compared to evaluate the potential adaptive significance of this polymorphism. Although seasonal variations in color morph proportions were not significant, some annual and geographic differences were. No differences were found among morphs related to the timing of various life history events. Studies of individual movements, dispersal,more » growth and survivorship also revealed no differences among morphs. Comparison of these data, as well as physiological and behavioral data for A. crepitans from Illinois, with similar data from Texas and elsewhere suggests that different factors must operate throughout the species range to maintain this color polymorphism. Chance may be a major factor in determining color morph proportions in localized populations in Illinois. 22 references, 5 figures, 3 tables.« less

The sensitivity to chlorhexidine and cetyl pyridinium chloride of staphylococci on the hands of dental students and theatre staff exposed to these disinfectants.

PubMed

Millns, B; Martin, M V; Field, E A

1994-02-01

The aim of this investigation was to study the possible emergence of resistant isolates of the genus Staphylococcus on the hands of dental personnel who use 'Hibiscrub' (chlorhexidine-detergent preparation) and cetyl pyridinium-coated gloves. Resistance was determined by a rate-of-kill technique. In four dental student groups (first, second, third and fourth years) no microorganisms survived 30 min exposure to cetyl pyridinium chloride (CPC) or to chlorhexidine diacetate (CDA). In a theatre staff group, no microorganisms survived 30 s exposure to CPC; and only one of 23 isolates survived 30 min exposure to CDA, but was killed after 60 min exposure. It is concluded that staphylococci resistant to either of these disinfectants do not present a problem in dental students or theatre staff.

Evolutionary Technique for Automated Synthesis of Electronic Circuits

NASA Technical Reports Server (NTRS)

Stoica, Adrian (Inventor); Salazar-Lazaro, Carlos Harold (Inventor)

2003-01-01

A method for evolving a circuit comprising configuring a plurality of transistors using a plurality of reconfigurable switches so that each of the plurality of transistors has a terminal coupled to a terminal of another of the plurality of transistors that is controllable by a single reconfigurable switch. The plurality of reconfigurable switches being controlled in response to a chromosome pattern. The plurality of reconfigurable switches may be controlled using an annealing function. As such, the plurality of reconfigurable switches may be controlled by selecting qualitative values for the plurality of reconfigurable switches in response to the chromosomal pattern, selecting initial quantitative values for the selected qualitative values, and morphing the initial quantitative values. Typically, subsequent quantitative values will be selected more divergent than the initial quantitative values. The morphing process may continue to partially or to completely polarize the quantitative values.

Isolation, characterization and antioxidative activity of C-phycocyanin from Limnothrix sp. strain 37-2-1

PubMed Central

Gantar, Miroslav; Simović, Dragan; Djilas, Sonja; Gonzalez, Walter W.; Miksovska, Jaroslava

2012-01-01

C-phycocyanin (C-PC) is a blue colored accessory photosynthetic pigment found in cyanobacteria. Some of the medicinal properties of Spirulina have been attributed to this pigment, which includes anticancer, antioxidant, and anti-inflammatory activity. We have screened cyanobacteria isolated from freshwater habitats in Florida for their high content of C-PC. Of 125 strains tested, one filamentous strain identified as Limnothrix sp. was selected for further research. This strain produced 18% C-PC of total dry biomass. Here we describe a simple method for obtaining C-PC of high purity without the use of ion exchange chromatography. The procedure is based on pigment precipitation from the cell lysate with an appropriate concentration of ammonium sulfate, then purification with activated carbon and chitosan, followed by a sample concentration using tangential flow filtration. We have shown that when the lower concentration of ammonium sulfate was used, C-PC with higher purity index was recovered. Characterization of C-PC from Limnothrix showed that it had an absorbance maximum at 620 nm and fluorescence at 639 nm. The molecular mass of intact C-PC was estimated to be ~50 kDa with α and β subunits forming dimmers. When C-PC content per unit biomass was compared to that of marketed Spirulina powder, we found that Limnothrix was superior. C-phycocyanin from Limnothrix had an antioxidative activity on DPPH free radicals similar to that found in a natural antioxidant – rutin. PMID:22353597

Delivering MC3T3-E1 cells into injectable calcium phosphate cement through alginate-chitosan microcapsules for bone tissue engineering*

PubMed Central

Qiao, Peng-yan; Li, Fang-fang; Dong, Li-min; Xu, Tao; Xie, Qiu-fei

2014-01-01

Objective: To deliver cells deep into injectable calcium phosphate cement (CPC) through alginate-chitosan (AC) microcapsules and investigate the biological behavior of the cells released from microcapsules into the CPC. Methods: Mouse osteoblastic MC3T3-E1 cells were embedded in alginate and AC microcapsules using an electrostatic droplet generator. The two types of cell-encapsulating microcapsules were then mixed with a CPC paste. MC3T3-E1 cell viability was investigated using a Wst-8 kit, and osteogenic differentiation was demonstrated by an alkaline phosphatase (ALP) activity assay. Cell attachment in CPC was observed by an environment scanning electron microscopy. Results: Both alginate and AC microcapsules were able to release the encapsulated MC3T3-E1 cells when mixed with CPC paste. The released cells attached to the setting CPC scaffolds, survived, differentiated, and formed mineralized nodules. Cells grew in the pores concomitantly created by the AC microcapsules in situ within the CPC. At Day 21, cellular ALP activity in the AC group was approximately four times that at Day 7 and exceeded that of the alginate microcapsule group (P<0.05). Pores formed by the AC microcapsules had a diameter of several hundred microns and were spherical compared with those formed by alginate microcapsules. Conclusions: AC microcapsule is a promising carrier to release seeding cells deep into an injectable CPC scaffold for bone engineering. PMID:24711359

β-Adrenergic Regulation of Cardiac Progenitor Cell Death Versus Survival and Proliferation

PubMed Central

Khan, Mohsin; Mohsin, Sadia; Avitabile, Daniele; Siddiqi, Sailay; Nguyen, Jonathan; Wallach, Kathleen; Quijada, Pearl; McGregor, Michael; Gude, Natalie; Alvarez, Roberto; Tilley, Douglas G.; Koch, Walter J.; Sussman, Mark A.

2013-01-01

Rationale Short-term β-adrenergic stimulation promotes contractility in response to stress but is ultimately detrimental in the failing heart because of accrual of cardiomyocyte death. Endogenous cardiac progenitor cell (CPC) activation may partially offset cardiomyocyte losses, but consequences of long-term β-adrenergic drive on CPC survival and proliferation are unknown. Objective We sought to determine the relationship between β-adrenergic activity and regulation of CPC function. Methods and Results Mouse and human CPCs express only β2 adrenergic receptor (β2-AR) in conjunction with stem cell marker c-kit. Activation of β2-AR signaling promotes proliferation associated with increased AKT, extracellular signal-regulated kinase 1/2, and endothelial NO synthase phosphorylation, upregulation of cyclin D1, and decreased levels of G protein–coupled receptor kinase 2. Conversely, silencing of β2-AR expression or treatment with β2-antagonist ICI 118, 551 impairs CPC proliferation and survival. β1-AR expression in CPC is induced by differentiation stimuli, sensitizing CPC to isoproterenol-induced cell death that is abrogated by metoprolol. Efficacy of β1-AR blockade by metoprolol to increase CPC survival and proliferation was confirmed in vivo by adoptive transfer of CPC into failing mouse myocardium. Conclusions β-adrenergic stimulation promotes expansion and survival of CPCs through β2-AR, but acquisition of β1-AR on commitment to the myocyte lineage results in loss of CPCs and early myocyte precursors. PMID:23243208

Comparative proteomic analysis of eggplant (Solanum melongena L.) heterostylous pistil development

PubMed Central

Li, Wenjia; Jiang, Yaqing; Song, Shiwei; Li, Yan; Chen, Riyuan

2017-01-01

Heterostyly is a common floral polymorphism, but the proteomic basis of this trait is still largely unexplored. In this study, self- and cross-pollination of L-morph and S-morph flowers and comparison of embryo sac development in eggplant (Solanum melongena L.) suggested that lower fruit set from S-morph flowers results from stigma-pollen incompatibility. To explore the molecular mechanism underlying heterostyly development, we conducted isobaric tags for relative and absolute quantification (iTRAQ) proteomic analysis of eggplant pistils for L- and S-morph flowers. A total of 5,259 distinct proteins were identified during heterostyly development. Compared S-morph flowers with L-morph, we discovered 57 and 184 differentially expressed proteins (DEPs) during flower development and maturity, respectively. Quantitative real time polymerase chain reactions were used for nine genes to verify DEPs from the iTRAQ approach. During flower development, DEPs were mainly involved in morphogenesis, biosynthetic processes, and metabolic pathways. At flower maturity, DEPs primarily participated in biosynthetic processes, metabolic pathways, and the formation of ribosomes and proteasomes. Additionally, some proteins associated with senescence and programmed cell death were found to be upregulated in S-morph pistils, which may lead to the lower fruit set in S-morph flowers. Although the exact roles of these related proteins are not yet known, this was the first attempt to use an iTRAQ approach to analyze proteomes of heterostylous eggplant flowers, and these results will provide insights into biochemical events taking place during the development of heterostyly. PMID:28586360

PROTECTED POLYMORPHISMS AND EVOLUTIONARY STABILITY OF PATCH-SELECTION STRATEGIES IN STOCHASTIC ENVIRONMENTS

PubMed Central

EVANS, STEVEN N.; HENING, ALEXANDRU; SCHREIBER, SEBASTIAN J.

2015-01-01

We consider a population living in a patchy environment that varies stochastically in space and time. The population is composed of two morphs (that is, individuals of the same species with different genotypes). In terms of survival and reproductive success, the associated phenotypes differ only in their habitat selection strategies. We compute invasion rates corresponding to the rates at which the abundance of an initially rare morph increases in the presence of the other morph established at equilibrium. If both morphs have positive invasion rates when rare, then there is an equilibrium distribution such that the two morphs coexist; that is, there is a protected polymorphism for habitat selection. Alternatively, if one morph has a negative invasion rate when rare, then it is asymptotically displaced by the other morph under all initial conditions where both morphs are present. We refine the characterization of an evolutionary stable strategy for habitat selection from [Schreiber, 2012] in a mathematically rigorous manner. We provide a necessary and sufficient condition for the existence of an ESS that uses all patches and determine when using a single patch is an ESS. We also provide an explicit formula for the ESS when there are two habitat types. We show that adding environmental stochasticity results in an ESS that, when compared to the ESS for the corresponding model without stochasticity, spends less time in patches with larger carrying capacities and possibly makes use of sink patches, thereby practicing a spatial form of bet hedging. PMID:25151369

Morph-specific differences in reproductive success in the distylous Primula veris in a context of habitat fragmentation

NASA Astrophysics Data System (ADS)

Van Rossum, Fabienne; De Sousa, Sara Campos; Triest, Ludwig

2006-11-01

Heterostylous self-incompatible plant species are particularly sensitive to habitat fragmentation and to disruption of pollination processes because of the need of intermorph cross-pollination for producing seeds. Heterostyly is characterized by sexual polymorphism through the occurrence of two (distyly) or three (tristyly) morph types that differ in floral traits (style length and anther position). We examined whether the long-styled (pin) and short-styled (thrum) morph types show differences in reproductive components and responses to habitat fragmentation in the distylous, self-incompatible perennial herb Primula veris. We documented reproductive components for pin and thrum individuals and their relationships with population size, plant density and morph ratio (pin frequency), in nine populations from Flanders (northern Belgium) located in fragmented habitats of the intensively used agricultural landscape. Seed abortion increased in small populations as a result of inbreeding depression. Fruit set increased with plant density. Seed set was positively related to pin proportion. Seed set was higher for pin than thrum in small populations, but lower in large populations. Two hypotheses can be considered to explain these morph-specific differences: a pollen transfer asymmetry, and a reproductive advantage for the partially self-compatible pin morph. Morph types appear to respond differently to habitat fragmentation constraints. A floral morph type showing partial self-compatibility may be favored in populations under pollination failure, because it can increase reproductive success and mating opportunities through intramorph crosses.

Evolutionary flight and enabling smart actuator devices

NASA Astrophysics Data System (ADS)

Manzo, Justin; Garcia, Ephrahim

2007-04-01

Recent interest in morphing vehicles with multiple, optimized configurations has led to renewed research on biological flight. The flying vertebrates - birds, bats, and pterosaurs - all made or make use of various morphing devices to achieve lift to suit rapidly changing flight demands, including maneuvers as complex as perching and hovering. The first part of this paper will discuss these devices, with a focus on the morphing elements and structural strong suits of each creature. Modern flight correlations to these devices will be discussed and analyzed as valid adaptations of these evolutionary traits. The second part of the paper will focus on the use of active joint structures for use in morphing aircraft devices. Initial work on smart actuator devices focused on NASA Langley's Hyper-Elliptical Cambered Span (HECS) wing platform, which led to development of a discretized spanwise curvature effector. This mechanism uses shape memory alloy (SMA) as the sole morphing actuator, allowing fast rotation with lightweight components at the expense of energy inefficiency. Phase two of morphing actuator development will add an element of active rigidity to the morphing structure, in the form of shape memory polymer (SMP). Employing a composite structure of polymer and alloy, this joint will function as part of a biomimetic morphing actuator system in a more energetically efficient manner. The joint is thermally actuated to allow compliance on demand and rigidity in the nominal configuration. Analytical and experimental joint models are presented, and potential applications on a bat-wing aircraft structure are outlined.

Limited improvement of incorporating primary circulating prostate cells with the CAPRA score to predict biochemical failure-free outcome of radical prostatectomy for prostate cancer.

PubMed

Murray, Nigel P; Aedo, Socrates; Fuentealba, Cynthia; Jacob, Omar; Reyes, Eduardo; Novoa, Camilo; Orellana, Sebastian; Orellana, Nelson

2016-10-01

To establish a prediction model for early biochemical failure based on the Cancer of the Prostate Risk Assessment (CAPRA) score, the presence or absence of primary circulating prostate cells (CPC) and the number of primary CPC (nCPC)/8ml blood sample is detected before surgery. A prospective single-center study of men who underwent radical prostatectomy as monotherapy for prostate cancer. Clinical-pathological findings were used to calculate the CAPRA score. Before surgery blood was taken for CPC detection, mononuclear cells were obtained using differential gel centrifugation, and CPCs identified using immunocytochemistry. A CPC was defined as a cell expressing prostate-specific antigen and P504S, and the presence or absence of CPCs and the number of cells detected/8ml blood sample was registered. Patients were followed up for up to 5 years; biochemical failure was defined as a prostate-specific antigen>0.2ng/ml. The validity of the CAPRA score was calibrated using partial validation, and the fractional polynomial Cox proportional hazard regression was used to build 3 models, which underwent a decision analysis curve to determine the predictive value of the 3 models with respect to biochemical failure. A total of 267 men participated, mean age 65.80 years, and after 5 years of follow-up the biochemical-free survival was 67.42%. The model using CAPRA score showed a hazards ratio (HR) of 5.76 between low and high-risk groups, that of CPC with a HR of 26.84 between positive and negative groups, and the combined model showed a HR of 4.16 for CAPRA score and 19.93 for CPC. Using the continuous variable nCPC, there was no improvement in the predictive value of the model compared with the model using a positive-negative result of CPC detection. The combined CAPRA-nCPC model showed an improvement of the predictive performance for biochemical failure using the Harrell׳s C concordance test and a net benefit on DCA in comparison with either model used separately. The use of primary CPC as a predictive factor based on their presence or absence did not predict aggressive disease or biochemical failure. Although the use of a combined CAPRA-nCPC model improves the prediction of biochemical failure in patients undergoing radical prostatectomy for prostate cancer, this is minimal. The use of the presence or absence of primary CPCs alone did not predict aggressive disease or biochemical failure. Copyright © 2016 Elsevier Inc. All rights reserved.

Large-scale parallel lattice Boltzmann-cellular automaton model of two-dimensional dendritic growth

NASA Astrophysics Data System (ADS)

Jelinek, Bohumir; Eshraghi, Mohsen; Felicelli, Sergio; Peters, John F.

2014-03-01

An extremely scalable lattice Boltzmann (LB)-cellular automaton (CA) model for simulations of two-dimensional (2D) dendritic solidification under forced convection is presented. The model incorporates effects of phase change, solute diffusion, melt convection, and heat transport. The LB model represents the diffusion, convection, and heat transfer phenomena. The dendrite growth is driven by a difference between actual and equilibrium liquid composition at the solid-liquid interface. The CA technique is deployed to track the new interface cells. The computer program was parallelized using the Message Passing Interface (MPI) technique. Parallel scaling of the algorithm was studied and major scalability bottlenecks were identified. Efficiency loss attributable to the high memory bandwidth requirement of the algorithm was observed when using multiple cores per processor. Parallel writing of the output variables of interest was implemented in the binary Hierarchical Data Format 5 (HDF5) to improve the output performance, and to simplify visualization. Calculations were carried out in single precision arithmetic without significant loss in accuracy, resulting in 50% reduction of memory and computational time requirements. The presented solidification model shows a very good scalability up to centimeter size domains, including more than ten million of dendrites. Catalogue identifier: AEQZ_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEQZ_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, UK Licensing provisions: Standard CPC license, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 29,767 No. of bytes in distributed program, including test data, etc.: 3131,367 Distribution format: tar.gz Programming language: Fortran 90. Computer: Linux PC and clusters. Operating system: Linux. Has the code been vectorized or parallelized?: Yes. Program is parallelized using MPI. Number of processors used: 1-50,000 RAM: Memory requirements depend on the grid size Classification: 6.5, 7.7. External routines: MPI (http://www.mcs.anl.gov/research/projects/mpi/), HDF5 (http://www.hdfgroup.org/HDF5/) Nature of problem: Dendritic growth in undercooled Al-3 wt% Cu alloy melt under forced convection. Solution method: The lattice Boltzmann model solves the diffusion, convection, and heat transfer phenomena. The cellular automaton technique is deployed to track the solid/liquid interface. Restrictions: Heat transfer is calculated uncoupled from the fluid flow. Thermal diffusivity is constant. Unusual features: Novel technique, utilizing periodic duplication of a pre-grown “incubation” domain, is applied for the scaleup test. Running time: Running time varies from minutes to days depending on the domain size and number of computational cores.

SMMP v. 3.0—Simulating proteins and protein interactions in Python and Fortran

NASA Astrophysics Data System (ADS)

Meinke, Jan H.; Mohanty, Sandipan; Eisenmenger, Frank; Hansmann, Ulrich H. E.

2008-03-01

We describe a revised and updated version of the program package SMMP. SMMP is an open-source FORTRAN package for molecular simulation of proteins within the standard geometry model. It is designed as a simple and inexpensive tool for researchers and students to become familiar with protein simulation techniques. SMMP 3.0 sports a revised API increasing its flexibility, an implementation of the Lund force field, multi-molecule simulations, a parallel implementation of the energy function, Python bindings, and more. Program summaryTitle of program:SMMP Catalogue identifier:ADOJ_v3_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADOJ_v3_0.html Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Licensing provisions:Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html Programming language used:FORTRAN, Python No. of lines in distributed program, including test data, etc.:52 105 No. of bytes in distributed program, including test data, etc.:599 150 Distribution format:tar.gz Computer:Platform independent Operating system:OS independent RAM:2 Mbytes Classification:3 Does the new version supersede the previous version?:Yes Nature of problem:Molecular mechanics computations and Monte Carlo simulation of proteins. Solution method:Utilizes ECEPP2/3, FLEX, and Lund potentials. Includes Monte Carlo simulation algorithms for canonical, as well as for generalized ensembles. Reasons for new version:API changes and increased functionality. Summary of revisions:Added Lund potential; parameters used in subroutines are now passed as arguments; multi-molecule simulations; parallelized energy calculation for ECEPP; Python bindings. Restrictions:The consumed CPU time increases with the size of protein molecule. Running time:Depends on the size of the simulated molecule.

Proteomic profiling of the antifungal drug response of Aspergillus fumigatus to voriconazole.

PubMed

Amarsaikhan, Nansalmaa; Albrecht-Eckardt, Daniela; Sasse, Christoph; Braus, Gerhard H; Ogel, Zumrut B; Kniemeyer, Olaf

2017-10-01

Antifungal resistance is an emerging problem and one of the reasons for treatment failure of invasive aspergillosis (IA). Voriconazole has become a standard therapeutic for the treatment of this often fatal infection. We studied the differentially expressed proteins as a response of Aspergillus fumigatus to voriconazole by employing the two-dimensional difference gel electrophoresis (DIGE) technique. Due to addition of drug, a total of 135 differentially synthesized proteins were identified by MALDI-TOF/TOF-mass spectrometry. In particular, the level of proteins involved in the general stress response and cell detoxification increased prominently. In contrast, cell metabolism and energy proteins were down-regulated, which suggests the cellular effort to maintain balance in energy utilization while trying to combat the cellular stress exerted by the drug. We detected several so-far uncharacterized proteins which may play a role in stress response and drug metabolism and which could be future targets for antifungal treatment. A mutant strain, which is deleted in the cross-pathway control gene cpcA, was treated with voriconazole to investigate the contribution of the general control of amino acid biosynthesis to drug resistance. We compared the mutant strain's protein expression profile with the wild-type strain. The absence of CpcA led to an increased resistance to voriconazole and a reduced activation of some general stress response proteins, while the transcript level of the triazole target gene erg11A (cyp51A) remained unchanged. In contrast, the sensitivity of strain ΔcpcA to terbinafine and amphotericin B was slightly increased. These findings imply a role of CpcA in the cellular stress response to azole drugs at the post transcriptional level. Copyright © 2017 Elsevier GmbH. All rights reserved.

Real-Time IRI driven by GIRO data

NASA Astrophysics Data System (ADS)

Galkin, Ivan; Huang, Xueqin; Reinisch, Bodo; Bilitza, Dieter; Vesnin, Artem

Real-time extensions of the empirical International Reference Ionosphere (IRI) model are based on assimilative techniques that preserve the IRI formalism which is optimized for the description of climatological ionospheric features. The Global Ionosphere Radio Observatory (GIRO) team has developed critical parts of an IRI Real Time Assimilative Model (IRTAM) for the global ionospheric plasma distribution using measured data available in real time from ~50 ionosondes of the GIRO network, The current assimilation results present global assimilative maps of foF2 and hmF2 that reproduce available data at the sensor sites and smoothly return to the climatological specifications when and where the data are missing, and are free from artificial sharp gradients and short-lived artifacts when viewed in time progression. Animated real-time maps of foF2 and hmF2 are published with a few minutes latency at http://giro.uml.edu/IRTAM/. Our real-time IRI modeling uses morphing, a technique that transforms the climatological ionospheric specifications to match the observations by iteratively computing corrections to the original coefficients of the diurnal/spatial expansions, used in IRI to map the key ionospheric characteristics, while keeping the IRI expansion basis formalism intact. Computation of the updated coefficient set for a given point in time includes analysis of the latest 24-hour history of observations, which allows the morphing technique to sense evolving ionospheric dynamics even with a sparse sensor network. A Non-linear Error Compensation Technique for Associative Restoration (NECTAR), one of the features in our morphing approach, has been in operation at the Lowell GIRO Data Center since 2013. The cornerstone of NECTAR is a recurrent neural network optimizer that is responsible for smoothing the transitions between the grid cells where observations are available. NECTAR has proved suitable for real-time operations that require the assimilation code to be considerate of data uncertainties (noise) and immune to data errors. Future IRTAM work is directed toward accepting a greater diversity of near-real-time sensor data, and the paper discusses potential new data sources and challenges associated with their assimilation.

77 FR 37879 - Cooperative Patent Classification External User Day

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-25

... Classification External User Day AGENCY: United States Patent and Trademark Office, Commerce. ACTION: Notice... Classification (CPC) External User Day event at its Alexandria Campus. CPC is a partnership between the USPTO and... classification system that will incorporate the best classification practices of the two Offices. This CPC event...

Functional Analysis of the Epidermal-Specific MYB Genes CAPRICE and WEREWOLF in Arabidopsis[W

PubMed Central

Tominaga, Rumi; Iwata, Mineko; Okada, Kiyotaka; Wada, Takuji

2007-01-01

Epidermis cell differentiation in Arabidopsis thaliana is a model system for understanding the developmental end state of plant cells. Two types of MYB transcription factors, R2R3-MYB and R3-MYB, are involved in cell fate determination. To examine the molecular basis of this process, we analyzed the functional relationship of the R2R3-type MYB gene WEREWOLF (WER) and the R3-type MYB gene CAPRICE (CPC). Chimeric constructs made from the R3 MYB regions of WER and CPC used in reciprocal complementation experiments showed that the CPC R3 region cannot functionally substitute for the WER R3 region in the differentiation of hairless cells. However, WER R3 can substantially substitute for CPC R3. There are no differences in yeast interaction assays of WER or WER chimera proteins with GLABRA3 (GL3) or ENHANCER OF GLABRA3 (EGL3). CPC and CPC chimera proteins also have similar activity in preventing GL3 WER and EGL3 WER interactions. Furthermore, we showed by gel mobility shift assays that WER chimera proteins do not bind to the GL2 promoter region. However, a CPC chimera protein, which harbors the WER R3 motif, still binds to the GL2 promoter region. PMID:17644729

Functional analysis of the epidermal-specific MYB genes CAPRICE and WEREWOLF in Arabidopsis.

PubMed

Tominaga, Rumi; Iwata, Mineko; Okada, Kiyotaka; Wada, Takuji

2007-07-01

Epidermis cell differentiation in Arabidopsis thaliana is a model system for understanding the developmental end state of plant cells. Two types of MYB transcription factors, R2R3-MYB and R3-MYB, are involved in cell fate determination. To examine the molecular basis of this process, we analyzed the functional relationship of the R2R3-type MYB gene WEREWOLF (WER) and the R3-type MYB gene CAPRICE (CPC). Chimeric constructs made from the R3 MYB regions of WER and CPC used in reciprocal complementation experiments showed that the CPC R3 region cannot functionally substitute for the WER R3 region in the differentiation of hairless cells. However, WER R3 can substantially substitute for CPC R3. There are no differences in yeast interaction assays of WER or WER chimera proteins with GLABRA3 (GL3) or ENHANCER OF GLABRA3 (EGL3). CPC and CPC chimera proteins also have similar activity in preventing GL3 WER and EGL3 WER interactions. Furthermore, we showed by gel mobility shift assays that WER chimera proteins do not bind to the GL2 promoter region. However, a CPC chimera protein, which harbors the WER R3 motif, still binds to the GL2 promoter region.

Chromatin Protein HP1α Interacts with the Mitotic Regulator Borealin Protein and Specifies the Centromere Localization of the Chromosomal Passenger Complex*

PubMed Central

Liu, Xing; Song, Zhenwei; Huo, Yuda; Zhang, Jiahai; Zhu, Tongge; Wang, Jianyu; Zhao, Xuannv; Aikhionbare, Felix; Zhang, Jiancun; Duan, Hequan; Wu, Jihui; Dou, Zhen; Shi, Yunyu; Yao, Xuebiao

2014-01-01

Accurate mitosis requires the chromosomal passenger protein complex (CPC) containing Aurora B kinase, borealin, INCENP, and survivin, which orchestrates chromosome dynamics. However, the chromatin factors that specify the CPC to the centromere remain elusive. Here we show that borealin interacts directly with heterochromatin protein 1α (HP1α) and that this interaction is mediated by an evolutionarily conserved PXVXL motif in the C-terminal borealin with the chromo shadow domain of HP1α. This borealin-HP1α interaction recruits the CPC to the centromere and governs an activation of Aurora B kinase judged by phosphorylation of Ser-7 in CENP-A, a substrate of Aurora B. Consistently, modulation of the motif PXVXL leads to defects in CPC centromere targeting and aberrant Aurora B activity. On the other hand, the localization of the CPC in the midzone is independent of the borealin-HP1α interaction, demonstrating the spatial requirement of HP1α in CPC localization to the centromere. These findings reveal a previously unrecognized but direct link between HP1α and CPC localization in the centromere and illustrate the critical role of borealin-HP1α interaction in orchestrating an accurate cell division. PMID:24917673

Control of Plant Trichome and Root-Hair Development by a Tomato (Solanum lycopersicum) R3 MYB Transcription Factor

PubMed Central

Tominaga-Wada, Rumi; Nukumizu, Yuka; Sato, Shusei; Wada, Takuji

2013-01-01

In Arabidopsis thaliana the CPC-like MYB transcription factors [CAPRICE (CPC), TRIPTYCHON (TRY), ENHANCER OF TRY AND CPC 1, 2, 3/CPC-LIKE MYB 3 (ETC1, ETC2, ETC3/CPL3), TRICHOMELESS 1, 2/CPC-LIKE MYB 4 (TCL1, TCL2/CPL4)] and the bHLH transcription factors [GLABRA3 (GL3) and ENHANCER OF GLABRA 3 (EGL3)] are central regulators of trichome and root-hair development. We identified TRY and GL3 homologous genes from the tomato genome and named them SlTRY and SlGL3, respectively. Phylogenic analyses revealed a close relationship between the tomato and Arabidopsis genes. Real-time reverse transcription PCR analyses showed that SlTRY and SlGL3 were predominantly expressed in aerial parts of developing tomato. After transformation into Arabidopsis, CPC::SlTRY inhibited trichome formation and enhanced root-hair differentiation by strongly repressing GL2 expression. On the other hand, GL3::SlGL3 transformation did not show any obvious effect on trichome or non-hair cell differentiation. These results suggest that tomato and Arabidopsis partially use similar transcription factors for epidermal cell differentiation, and that a CPC-like R3 MYB may be a key common regulator of plant trichome and root-hair development. PMID:23326563

A robust approach for ECG-based analysis of cardiopulmonary coupling.

PubMed

Zheng, Jiewen; Wang, Weidong; Zhang, Zhengbo; Wu, Dalei; Wu, Hao; Peng, Chung-Kang

2016-07-01

Deriving respiratory signal from a surface electrocardiogram (ECG) measurement has advantage of simultaneously monitoring of cardiac and respiratory activities. ECG-based cardiopulmonary coupling (CPC) analysis estimated by heart period variability and ECG-derived respiration (EDR) shows promising applications in medical field. The aim of this paper is to provide a quantitative analysis of the ECG-based CPC, and further improve its performance. Two conventional strategies were tested to obtain EDR signal: R-S wave amplitude and area of the QRS complex. An adaptive filter was utilized to extract the common component of inter-beat interval (RRI) and EDR, generating enhanced versions of EDR signal. CPC is assessed through probing the nonlinear phase interactions between RRI series and respiratory signal. Respiratory oscillations presented in both RRI series and respiratory signals were extracted by ensemble empirical mode decomposition for coupling analysis via phase synchronization index. The results demonstrated that CPC estimated from conventional EDR series exhibits constant and proportional biases, while that estimated from enhanced EDR series is more reliable. Adaptive filtering can improve the accuracy of the ECG-based CPC estimation significantly and achieve robust CPC analysis. The improved ECG-based CPC estimation may provide additional prognostic information for both sleep medicine and autonomic function analysis. Copyright © 2016 IPEM. Published by Elsevier Ltd. All rights reserved.

Maxillary sinus floor elevation using a tissue-engineered bone with calcium-magnesium phosphate cement and bone marrow stromal cells in rabbits.

PubMed

Zeng, Deliang; Xia, Lunguo; Zhang, Wenjie; Huang, Hui; Wei, Bin; Huang, Qingfeng; Wei, Jie; Liu, Changsheng; Jiang, Xinquan

2012-04-01

The objective of this study was to assess the effects of maxillary sinus floor elevation with a tissue-engineered bone constructed with bone marrow stromal cells (bMSCs) and calcium-magnesium phosphate cement (CMPC) material. The calcium (Ca), magnesium (Mg), and phosphorus (P) ions released from calcium phosphate cement (CPC), magnesium phosphate cement (MPC), and CMPC were detected by inductively coupled plasma atomic emission spectroscopy (ICP-AES), and the proliferation and osteogenic differentiation of bMSCs seeded on CPC, MPC, and CMPC or cultured in CPC, MPC, and CMPC extracts were measured by MTT analysis, alkaline phosphatase (ALP) activity assay, alizarin red mineralization assay, and real-time PCR analysis of the osteogenic genes ALP and osteocalcin (OCN). Finally, bMSCs were combined with CPC, MPC, and CMPC and used for maxillary sinus floor elevation in rabbits, while CPC, MPC, or CMPC without cells served as control groups. The new bone formation in each group was detected by histological finding and fluorochrome labeling at weeks 2 and 8 after surgical operation. It was observed that the Ca ion concentrations of the CMPC and CPC scaffolds was significantly higher than that of the MPC scaffold, while the Mg ions concentration of CMPC and MPC was significantly higher than that of CPC. The bMSCs seeded on CMPC and MPC or cultured in their extracts proliferated more quickly than the cells seeded on CPC or cultured in its extract, respectively. The osteogenic differentiation of bMSCs seeded on CMPC and CPC or cultured in the corresponding extracts was significantly enhanced compared to that of bMSCs seeded on MPC or cultured in its extract; however, there was no significant difference between CMPC and CPC. As for maxillary sinus floor elevation in vivo, CMPC could promote more new bone formation and mineralization compared to CPC and MPC, while the addition of bMSCs could further enhance its new bone formation ability significantly. Our data suggest that CMPC possesses moderate biodegradability and excellent osteoconductivity, which may be attributed to its Ca and Mg ion composition, and the tissue-engineered bone constructed of CMPC and bMSCs might be a potential alterative graft for maxillofacial bone regeneration.

The application of thermally induced multistable composites to morphing aircraft structures

NASA Astrophysics Data System (ADS)

Mattioni, Filippo; Weaver, Paul M.; Potter, Kevin D.; Friswell, Michael I.

2008-03-01

One approach to morphing aircraft is to use bistable or multistable structures that have two or more stable equilibrium configurations to define a discrete set of shapes for the morphing structure. Moving between these stable states may be achieved using an actuation system or by aerodynamic loads. This paper considers three concepts for morphing aircraft based on multistable structures, namely a variable sweep wing, bistable blended winglets and a variable camber trailing edge. The philosophy behind these concepts is outlined, and simulated and experimental results are given.

AVST Morphing Project Research Summaries in Fiscal Year 2001

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria R.

2002-01-01

The Morphing project at the National Aeronautics and Space Agency's Langley Research Center is part of the Aerospace Vehicle Systems Program Office that conducts fundamental research on advanced technologies for future flight vehicles. The objectives of the Morphing project are to develop and assess advanced technologies and integrated component concepts to enable efficient, multi-point adaptability in air and space vehicles. In the context of the project, the word "morphing" is defined as "efficient, multi-point adaptability" and may include micro or macro, structural or fluidic approaches. The current document on the Morphing project is a compilation of research summaries and other information on the project from fiscal year 2001. The focus of this document is to provide a brief overview of the project content, technical results and lessons learned from fiscal year 2001.

Experimental multiphysical characterization of an SMA driven, camber morphing owl wing section

NASA Astrophysics Data System (ADS)

Stroud, Hannah R.; Leal, Pedro B. C.; Hartl, Darren J.

2018-03-01

In the context of aerospace engineering, morphing structures are useful in their ability to change the outer mold line (OML) while improving or maintaining certain aerodynamic performance metrics. Skin-based morphing is of particular interest in that it minimizes installation volume. Shape memory alloys (SMAs) have a high force to volume ratio that makes them a suitable choice for skin-based morphing. Because the thermomechanical properties of SMAs are coupled, strain can be generated via a temperature variation; this phenomenon is used as the actuation method. Therefore, it is necessary to determine the interaction of the system not only with aerodynamic loads, but with thermal loads as well. This paper describes the wind tunnel testing and in situ thermomechanical analysis of an SMA actuated, avian inspired morphing wing. The morphing wing is embedded with two SMA composite actuators and consists of a foam core enveloped in a fiberglass-epoxy composite. As the SMA wire is heated, the actuator contracts, morphing the wing from the original owl OML to a highly cambered, high lift OML. Configuration characteristics are analyzed in situ using simultaneous three dimensional digital image correlation (DIC) and infrared thermography, thereby coupling strain and thermal measurements. This method of testing allows for the nonintrusive, multiphysical data acquisition of each actuator separately and the system as a whole.

Functional dissociation of the left and right fusiform gyrus in self-face recognition.

PubMed

Ma, Yina; Han, Shihui

2012-10-01

It is well known that the fusiform gyrus is engaged in face perception, such as the processes of face familiarity and identity. However, the functional role of the fusiform gyrus in face processing related to high-level social cognition remains unclear. The current study assessed the functional role of individually defined fusiform face area (FFA) in the processing of self-face physical properties and self-face identity. We used functional magnetic resonance imaging to monitor neural responses to rapidly presented face stimuli drawn from morph continua between self-face (Morph 100%) and a gender-matched friend's face (Morph 0%) in a face recognition task. Contrasting Morph 100% versus Morph 60% that differed in self-face physical properties but were both recognized as the self uncovered neural activity sensitive to self-face physical properties in the left FFA. Contrasting Morphs 50% that were recognized as the self versus a friend on different trials revealed neural modulations associated with self-face identity in the right FFA. Moreover, the right FFA activity correlated with the frequency of recognizing Morphs 50% as the self. Our results provide evidence for functional dissociations of the left and right FFAs in the representations of self-face physical properties and self-face identity. Copyright © 2011 Wiley Periodicals, Inc.

Development and Validation of the Morphing Fear Questionnaire (MFQ).

PubMed

Zysk, Eva; Shafran, Roz; Williams, Tim I; Melli, Gabriele

2016-11-01

Morphing fears (also called transformation obsessions) involve concerns that a person may become contaminated by and acquire undesirable characteristics of others. These symptoms are found in patients with obsessive-compulsive disorder (OCD) and are thought to be related to mental contamination. Given the high levels of distress and interference morphing fears can cause, a reliable and valid assessment measure is needed. This article describes the development and evaluation of the Morphing Fear Questionnaire (MFQ), a 13-item measure designed to assess for the presence and severity of morphing fears. A sample of 900 participants took part in the research. Of these, 140 reported having a current diagnosis of OCD (SR-OCD) and 760 reported never having had OCD (N-OCD; of whom 24 reported a diagnosis of an anxiety disorder and 23 reported a diagnosis of depression). Factor structure, reliability and construct and criterion-related validity were investigated. Exploratory and confirmatory factor analyses supported a one-factor structure replicable across the N-OCD and SR-OCD group. The MFQ was found to have high internal consistency and good temporal stability and showed significantly greater associations with convergent measures (assessing obsessive-compulsive symptoms, mental contamination, thought-action fusion and magical thinking) than with divergent measures (assessing depression and anxiety). Moreover, the MFQ successfully discriminated between the SR-OCD sample and the N-OCD group, anxiety disorder sample and depression sample. These findings suggest that the MFQ has sound psychometric properties and that it can be used to assess morphing fear. Clinical implications are discussed. Copyright © 2015 John Wiley & Sons, Ltd. Little remains known about morphing fears, but it is an important area of investigation due to symptoms being highly distressing and often debilitating Because morphing fears commonly present as obscure symptoms, they may not be recognized as a type of OCD The MFQ is a robust measure with clinical utility; it can facilitate recognition and assessment of morphing fears The MFQ will allow for further investigations of the prevalence, correlates and treatment outcomes of morphing fears. Copyright © 2015 John Wiley & Sons, Ltd.

Adaptive Significance of Flexistyly in Alpinia blepharocalyx (Zingiberaceae): A Hand-pollination Experiment

PubMed Central

Sun, Shan; Gao, Jiang-Yun; Liao, Wan-Jin; Li, Qing-Jun; Zhang, Da-Yong

2007-01-01

Background and Aims Flexistyly is a sexual dimorphism where there are two morphs that differ in the temporal expression of sexual function and also involve reciprocal movement of the stigmatic surface through a vertical axis during the flowering period. The adaptive significance of flexistyly has been interpreted as a floral mechanism for outcrossing, but it may also function to reduce sexual interference in which styles and stigmas impede the pollen export. Here these two explanations of flexistyly were tested in Alpinia blepharocalyx through a hand-pollination experiment. Methods Hand-pollinations were performed in two temporal morphs and consisted of two sequential pollination treatments, namely self-pollination in the morning and inter-morph pollination in the afternoon (treatment 1) or conversely inter-morph pollination in the morning and self-pollination in the afternoon (treatment 2), and two simultaneous self- and inter-morph cross-pollination treatments either in the morning (treatment 3) or in the afternoon (treatment 4). Seed paternity was then determined to assess relative success of self- versus cross-pollen using allozyme markers. Key Results In the sequential pollination treatments, whether the stigmas of recipients are receptive in the morning is crucial to the success of the pollen deposited. When the cataflexistylous (protandrous) morph served as pollen recipient, early-arriving pollen in the morning can sire only a very small proportion (<15%) of seeds because the stigmas were then unreceptive. However, when the anaflexistylous (protogynous) morph served as pollen recipient, early pollen did gain a large competitive advantage over the late pollen, particularly when cross-pollen arrived first. Simultaneous self- and inter-morph cross-pollination indicated that outcross-pollen is more competitive than self-pollen on receptive stigmas. Conclusions Differential maturing of male and female organs in Alpinia blepharocalyx is sufficient for selfing avoidance, obviating the need for style movements. Instead, the upward style curvature of the cataflexistylous morph in the morning and the anaflexistylous morph in the afternoon most likely represents a means of reducing interference with pollen export. PMID:17237211

Alteration of mitochondrial membrane potential by Spirulina platensis C-phycocyanin induces apoptosis in the doxorubicinresistant human hepatocellular-carcinoma cell line HepG2.

PubMed

Roy, Karnati R; Arunasree, Kalle M; Reddy, Nishant P; Dheeraj, Bhavanasi; Reddy, Gorla Venkateswara; Reddanna, Pallu

2007-07-01

C-PC (C-phycocyanin) is a water-soluble biliprotein from the filamentous cyanobacterium Spirulina platensis with potent antioxidant, anti-inflammatory and anticancerous properties. In the present study, the effect of C-PC was tested on the proliferation of doxorubicin-sensitive (S-HepG2) and -resistant (R-HepG2) HCC (hepatocellular carcinoma) cell lines. These studies indicate a 50% decrease in the proliferation of S- and R-HepG2 cells treated with 40 and 50 microM C-PC for 24 h respectively. C-PC also enhanced the sensitivity of R-HepG2 cells to doxorubicin. R-HepG2 cells treated with C-PC showed typical apoptotic features such as membrane blebbing and DNA fragmentation. Flow-cytometric analysis of R-HepG2 cells treated with 10, 25 and 50 microM C-PC for 24 h showed 18.8, 39.72 and 65.64% cells in sub-G(0)/G(1)-phase respectively. Cytochrome c release, decrease in membrane potential, caspase 3 activation and PARP [poly(ADP-ribose) polymerase] cleavage were observed in C-PC-treated R-HepG2 cells. These studies also showed down-regulation of the anti-apoptotic protein Bcl-2 and up-regulation of the pro-apoptotic Bax (Bcl2-associated X-protein) protein in the R-HepG2 cells treated with C-PC. The present study thus demonstrates that C-PC induces apoptosis in R-HepG2 cells and its potential as an anti-HCC agent.

Odour-Mediated Orientation of Beetles Is Influenced by Age, Sex and Morph

PubMed Central

Arnold, Sarah E. J.; Stevenson, Philip C.; Belmain, Steven R.

2012-01-01

The behaviour of insects is dictated by a combination of factors and may vary considerably between individuals, but small insects are often considered en masse and thus these differences can be overlooked. For example, the cowpea bruchid Callosobruchus maculatus F. exists naturally in two adult forms: the active (flight) form for dispersal, and the inactive (flightless), more fecund but shorter-lived form. Given that these morphs show dissimilar biology, it is possible that they differ in odour-mediated orientation and yet studies of this species frequently neglect to distinguish morph type, or are carried out only on the inactive morph. Along with sex and age of individual, adult morph could be an important variable determining the biology of this and similar species, informing studies on evolution, ecology and pest management. We used an olfactometer with motion-tracking to investigate whether the olfactory behaviour and orientation of C. maculatus towards infested and uninfested cowpeas and a plant-derived repellent compound, methyl salicylate, differed between morphs or sexes. We found significant differences between the behaviour of male and female beetles and beetles of different ages, as well as interactive effects of sex, morph and age, in response to both host and repellent odours. This study demonstrates that behavioural experiments on insects should control for sex and age, while also considering differences between adult morphs where present in insect species. This finding has broad implications for fundamental entomological research, particularly when exploring the relationships between physiology, behaviour and evolutionary biology, and the application of crop protection strategies. PMID:23145074

Mutualists and antagonists drive among-population variation in selection and evolution of floral display in a perennial herb

PubMed Central

Ågren, Jon; Hellström, Frida; Toräng, Per; Ehrlén, Johan

2013-01-01

Spatial variation in the direction of selection drives the evolution of adaptive differentiation. However, few experimental studies have examined the relative importance of different environmental factors for variation in selection and evolutionary trajectories in natural populations. Here, we combine 8 y of observational data and field experiments to assess the relative importance of mutualistic and antagonistic interactions for spatial variation in selection and short-term evolution of a genetically based floral display dimorphism in the short-lived perennial herb Primula farinosa. Natural populations of this species include two floral morphs: long-scaped plants that present their flowers well above the ground and short-scaped plants with flowers positioned close to the ground. The direction and magnitude of selection on scape morph varied among populations, and so did the frequency of the short morph (median 19%, range 0–100%; n = 69 populations). A field experiment replicated at four sites demonstrated that variation in the strength of interactions with grazers and pollinators were responsible for among-population differences in relative fitness of the two morphs. Selection exerted by grazers favored the short-scaped morph, whereas pollinator-mediated selection favored the long-scaped morph. Moreover, variation in selection among natural populations was associated with differences in morph frequency change, and the experimental removal of grazers at nine sites significantly reduced the frequency of the short-scaped morph over 8 y. The results demonstrate that spatial variation in intensity of grazing and pollination produces a selection mosaic, and that changes in biotic interactions can trigger rapid genetic changes in natural plant populations. PMID:24145439

Mutualists and antagonists drive among-population variation in selection and evolution of floral display in a perennial herb.

PubMed

Agren, Jon; Hellström, Frida; Toräng, Per; Ehrlén, Johan

2013-11-05

Spatial variation in the direction of selection drives the evolution of adaptive differentiation. However, few experimental studies have examined the relative importance of different environmental factors for variation in selection and evolutionary trajectories in natural populations. Here, we combine 8 y of observational data and field experiments to assess the relative importance of mutualistic and antagonistic interactions for spatial variation in selection and short-term evolution of a genetically based floral display dimorphism in the short-lived perennial herb Primula farinosa. Natural populations of this species include two floral morphs: long-scaped plants that present their flowers well above the ground and short-scaped plants with flowers positioned close to the ground. The direction and magnitude of selection on scape morph varied among populations, and so did the frequency of the short morph (median 19%, range 0-100%; n = 69 populations). A field experiment replicated at four sites demonstrated that variation in the strength of interactions with grazers and pollinators were responsible for among-population differences in relative fitness of the two morphs. Selection exerted by grazers favored the short-scaped morph, whereas pollinator-mediated selection favored the long-scaped morph. Moreover, variation in selection among natural populations was associated with differences in morph frequency change, and the experimental removal of grazers at nine sites significantly reduced the frequency of the short-scaped morph over 8 y. The results demonstrate that spatial variation in intensity of grazing and pollination produces a selection mosaic, and that changes in biotic interactions can trigger rapid genetic changes in natural plant populations.

Passive morphing of flying wing aircraft: Z-shaped configuration

NASA Astrophysics Data System (ADS)

Mardanpour, Pezhman; Hodges, Dewey H.

2014-01-01

High Altitude, Long Endurance (HALE) aircraft can achieve sustained, uninterrupted flight time if they use solar power. Wing morphing of solar powered HALE aircraft can significantly increase solar energy absorbency. An example of the kind of morphing considered in this paper requires the wings to fold so as to orient a solar panel to be hit more directly by the sun's rays at specific times of the day. An example of the kind of morphing considered in this paper requires the wings to fold so as to orient a solar panel that increases the absorption of solar energy by decreasing the angle of incidence of the solar radiation at specific times of the day. In this paper solar powered HALE flying wing aircraft are modeled with three beams with lockable hinge connections. Such aircraft are shown to be capable of morphing passively, following the sun by means of aerodynamic forces and engine thrusts. The analysis underlying NATASHA (Nonlinear Aeroelastic Trim And Stability of HALE Aircraft), a computer program that is based on geometrically exact, fully intrinsic beam equations and a finite-state induced flow model, was extended to include the ability to simulate morphing of the aircraft into a "Z" configuration. Because of the "long endurance" feature of HALE aircraft, such morphing needs to be done without relying on actuators and at as near zero energy cost as possible. The emphasis of this study is to substantially demonstrate the processes required to passively morph a flying wing into a Z-shaped configuration and back again.

Climate Prediction Center - Outlooks: UV Alert Forecast

Science.gov Websites

Organization Search Go Search the CPC Go About Us Our Mission Who We Are Contact Us CPC Information CPC Web Team USA.gov is the U.S. Government's official Web portal to all Federal, state and local government Web resources and services. HOME > Stratosphere Home > Stratosphere UV Index > UV Alert

Climate Prediction Center - Monitoring Atlantic Hurricane Potential

Science.gov Websites

Organization Search Go Search the CPC Go About Us Our Mission Who We Are Contact Us CPC Information CPC Web Team USA.gov is the U.S. Government's official Web portal to all Federal, state and local government Web resources and services. HOME > Monitoring and Data > Monitoring Atlantic Hurricane Potential

[Reversed clinicopathological conference (R-CPC)--interpreting laboratory data in the same way as physical findings].

PubMed

Sugano, Mitsutoshi; Shimada, Masashi; Moriyoshi, Miho; Kitagawa, Kiyoki; Nakashima, Hiromi; Wada, Hideo; Yanagihara, Katsunori; Fujisawa, Shinya; Yonekawa, Osamu; Honda, Takayuki

2012-05-01

Routine laboratory data are discussed by time series analysis in reversed clinicopathological conferences (R-CPC) at Shinshu University School of Medicine. We can identify fine changes in the laboratory data and the importance of negative data (without any changes) using time series analysis. Routine laboratory tests can be performed repeatedly and relatively cheaply, and time series analysis can be performed. The examination process of routine laboratory data in the R-CPC is almost the same as the process of taking physical findings. Firstly, general findings are checked and then the state of each organ is examined. Although routine laboratory data are cheap, we can obtain much more information about a patient's state than from physical examinations. In this R-CPC, several specialists in the various fields of laboratory medicine discussed the routine laboratory data of a patient, and we tried to understand the detailed state of the patient. R-CPC is an educational method to examine laboratory data and we, reconfirmed the usefulness of R-CPC to elucidate the clinical state of the patient.

Arabidopsis CAPRICE (MYB) and GLABRA3 (bHLH) Control Tomato (Solanum lycopersicum) Anthocyanin Biosynthesis

PubMed Central

Wada, Takuji; Kunihiro, Asuka; Tominaga-Wada, Rumi

2014-01-01

In Arabidopsis thaliana the MYB transcription factor CAPRICE (CPC) and the bHLH transcription factor GLABRA3 (GL3) are central regulators of root-hair differentiation and trichome initiation. By transforming the orthologous tomato genes SlTRY (CPC) and SlGL3 (GL3) into Arabidopsis, we demonstrated that these genes influence epidermal cell differentiation in Arabidopsis, suggesting that tomato and Arabidopsis partially use similar transcription factors for epidermal cell differentiation. CPC and GL3 are also known to be involved in anthocyanin biosynthesis. After transformation into tomato, 35S::CPC inhibited anthocyanin accumulation, whereas GL3::GL3 enhanced anthocyanin accumulation. Real-time reverse transcription PCR analyses showed that the expression of anthocyanin biosynthetic genes including Phe-ammonia lyase (PAL), the flavonoid pathway genes chalcone synthase (CHS), dihydroflavonol reductase (DFR), and anthocyanidin synthase (ANS) were repressed in 35S::CPC tomato. In contrast, the expression levels of PAL, CHS, DFR, and ANS were significantly higher in GL3::GL3 tomato compared with control plants. These results suggest that CPC and GL3 also influence anthocyanin pigment synthesis in tomato. PMID:25268379

Regulation of CAPRICE transcription by MYB proteins for root epidermis differentiation in Arabidopsis.

PubMed

Koshino-Kimura, Yoshihiro; Wada, Takuji; Tachibana, Tatsuhiko; Tsugeki, Ryuji; Ishiguro, Sumie; Okada, Kiyotaka

2005-06-01

Epidermal cell differentiation in Arabidopsis root is studied as a model system for understanding cell fate specification. Two types of MYB-related transcription factors are involved in this cell differentiation. One of these, CAPRICE (CPC), encoding an R3-type MYB protein, is a positive regulator of hair cell differentiation and is preferentially transcribed in hairless cells. We analyzed the regulatory mechanism of CPC transcription. Deletion analyses of the CPC promoter revealed that hairless cell-specific transcription of the CPC gene required a 69 bp sequence, and a tandem repeat of this region was sufficient for its expression in epidermis. This region includes two MYB-binding sites, and the epidermis-specific transcription of CPC was abolished when base substitutions were introduced in these sites. We showed by gel mobility shift experiments and by yeast one-hybrid assay that WEREWOLF (WER), which is an R2R3-type MYB protein, directly binds to this region. We showed that WER also binds to the GL2 promoter region, indicating that WER directly regulates CPC and GL2 transcription by binding to their promoter regions.

The Perception of Prototypical Motion: Synchronization Is Enhanced with Quantitatively Morphed Gestures of Musical Conductors

ERIC Educational Resources Information Center

Wollner, Clemens; Deconinck, Frederik J. A.; Parkinson, Jim; Hove, Michael J.; Keller, Peter E.

2012-01-01

Aesthetic theories have long suggested perceptual advantages for prototypical exemplars of a given class of objects or events. Empirical evidence confirmed that morphed (quantitatively averaged) human faces, musical interpretations, and human voices are preferred over most individual ones. In this study, biological human motion was morphed and…

Evolving and Combining Facial Composites: Between-Witness and Within-Witness Morphs Compared

ERIC Educational Resources Information Center

Valentine, Tim; Davis, Josh P.; Thorner, Kate; Solomon, Chris; Gibson, Stuart

2010-01-01

Student participant-witnesses produced 4 composites of unfamiliar faces with a system that uses a genetic algorithm to evolve appearance of artificial faces. Morphs of 4 composites produced by different witnesses (between-witness morphs) were judged better likenesses (Experiment 1) and were more frequently named (Experiment 2) by participants who…

Multiple exaggerated weapon morphs: a novel form of male polymorphism in harvestmen

PubMed Central

Painting, Christina J.; Probert, Anna F.; Townsend, Daniel J.; Holwell, Gregory I.

2015-01-01

Alternative reproductive tactics in animals are commonly associated with distinct male phenotypes resulting in polymorphism of sexually selected weapons such as horns and spines. Typically, morphs are divided between small (unarmed) and large (armed) males according to one or more developmental thresholds in association with body size. Here, we describe remarkable weapon trimorphism within a single species, where two exaggerated weapon morphs and a third morph with reduced weaponry are present. Male Pantopsalis cheliferoides harvestmen display exaggerated chelicerae (jaws) which are highly variable in length among individuals. Across the same body size spectrum, however, some males belong to a distinct second exaggerated morph which possesses short, broad chelicerae. Multiple weapon morphs in a single species is a previously unknown phenomenon and our findings have significant implications for understanding weapon diversity and maintenance of polymorphism. Specifically, this species will be a valuable model for testing how weapons diverge by being able to test directly for the circumstances under which a certain weapon type is favoured and how weapon shape relates to performance. PMID:26542456

Evolution and coexistence of pollination ecotypes in an African Gladiolus (Iridaceae).

PubMed

Anderson, Bruce; Alexandersson, Ronny; Johnson, Steven D

2010-04-01

Pollinator-mediated selection has been suggested as a key driver of speciation in plants. We examined the potential role of hawkmoth pollinators in driving allopatric divergence and maintaining sympatric coexistence of morphotypes in the African iris Gladiolus longicollis. Floral tube length in this species varies from 35 mm to 130 mm across its geographic range and reflects the prevailing tongue lengths of local hawkmoth assemblages. The distribution of floral tube lengths is bimodal with two relatively discrete categories--long (about 90 mm) or short (about 50 mm)--that match the bimodal distribution of hawkmoth tongue lengths in eastern South Africa. At a contact site between these two floral morphs, we found few individuals of intermediate length, suggesting limited gene flow between morphs despite their interfertility. A difference in flowering phenology appears to be the main isolating barrier between morphs at this site. Long- and short-tubed morphs differed markedly in the chemical composition of their floral fragrance, a trait that could be used as a cue for morph-specific foraging by hawkmoths. Positive directional selection on tube length was found to occur in both morphs.

Heterospecific aggression bias towards a rarer colour morph.

PubMed

Lehtonen, Topi K; Sowersby, Will; Wong, Bob B M

2015-09-22

Colour polymorphisms are a striking example of phenotypic diversity, yet the sources of selection that allow different morphs to persist within populations remain poorly understood. In particular, despite the importance of aggression in mediating social dominance, few studies have considered how heterospecific aggression might contribute to the maintenance or divergence of different colour morphs. To redress this gap, we carried out a field-based study in a Nicaraguan crater lake to investigate patterns of heterospecific aggression directed by the cichlid fish, Hypsophrys nicaraguensis, towards colour polymorphic cichlids in the genus Amphilophus. We found that H. nicaraguensis was the most frequent territorial neighbour of the colour polymorphic A. sagittae. Furthermore, when manipulating territorial intrusions using models, H. nicaraguensis were more aggressive towards the gold than dark colour morph of the sympatric Amphilophus species, including A. sagittae. Such a pattern of heterospecific aggression should be costly to the gold colour morph, potentially accounting for its lower than expected frequency and, more generally, highlighting the importance of considering heterospecific aggression in the context of morph frequencies and coexistence in the wild. © 2015 The Author(s).

PhotoMorphs™: A Novel Light-Activated Reagent for Controlling Gene Expression in Zebrafish

PubMed Central

Tomasini, Amber J.; Schuler, Aaron D.; Zebala, John A.; Mayer, Alan N.

2009-01-01

Manipulating gene expression in zebrafish is critical for exploiting the full potential of this vertebrate model organism. Morpholino oligos are the most commonly employed antisense technology for knocking down gene expression. However, morpholinos suffer from a lack of control over the timing and location of knockdown. In this report, we describe a novel light-activatable knockdown reagent called PhotoMorph™. PhotoMorphs can be generated from existing morpholinos by hybridization with a complementary caging strand containing a photocleavable linkage. The caging strand neutralizes the morpholino activity until irradiation of the PhotoMorph with UV light releases the morpholino. We generated PhotoMorphs to target genes encoding enhanced green fluorescent protein (EGFP), No tail, and E-cadherin to illustrate the utility of this approach. Temporal control of gene expression with PhotoMorphs permitted us to circumvent the early lethal phenotype of E-cadherin knockdown. A splice-blocking PhotoMorph directed to the rheb gene showed light-dependent gene knockdown up to 72 hpf. PhotoMorphs thus offer a new class of laboratory reagents suitable for the spatiotemporal control of gene expression in the zebrafish. PMID:19644983

Adaptive wing structures

NASA Astrophysics Data System (ADS)

Reed, John L., Jr.; Hemmelgarn, Christopher D.; Pelley, Bryan M.; Havens, Ernie

2005-05-01

Cornerstone Research Group, Inc. (CRG) is developing a unique adaptive wing structure intended to enhance the capability of loitering Unmanned Air Vehicles (UAVs). In order to tailor the wing design to a specific application, CRG has developed a wing structure capable of morphing in chord and increasing planform area by 80 percent. With these features, aircraft will be capable of optimizing their flight efficiency throughout the entire mission profile. The key benefit from this morphing design is increased maneuverability, resulting in improved effectiveness over the current design. During the development process CRG has overcome several challenges in the design of such a structure while incorporating advanced materials capable of maintaining aerodynamic shape and transferring aerodynamic loads while enabling crucial changes in planform shape. To overcome some of these challenges, CRG is working on integration of their shape memory polymer materials into the wing skin to enable seamless morphing. This paper will address the challenges associated with the development of a morphing aerospace structure capable of such large shape change, the materials necessary for enabling morphing capabilities, and the current status of the morphing program within CRG.

Early Examples from the Integrated Multi-Satellite Retrievals for GPM (IMERG)

NASA Astrophysics Data System (ADS)

Huffman, George; Bolvin, David; Braithwaite, Daniel; Hsu, Kuolin; Joyce, Robert; Kidd, Christopher; Sorooshian, Soroosh; Xie, Pingping

2014-05-01

The U.S. GPM Science Team's Day-1 algorithm for computing combined precipitation estimates as part of GPM is the Integrated Multi-satellitE Retrievals for GPM (IMERG). The goal is to compute the best time series of (nearly) global precipitation from "all" precipitation-relevant satellites and global surface precipitation gauge analyses. IMERG is being developed as a unified U.S. algorithm drawing on strengths in the three contributing groups, whose previous work includes: 1) the TRMM Multi-satellite Precipitation Analysis (TMPA); 2) the CPC Morphing algorithm with Kalman Filtering (K-CMORPH); and 3) the Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks using a Cloud Classification System (PERSIANN-CCS). We review the IMERG design and development, plans for testing, and current status. Some of the lessons learned in running and reprocessing the previous data sets include the importance of quality-controlling input data sets, strategies for coping with transitions in the various input data sets, and practical approaches to retrospective analysis of multiple output products (namely the real- and post-real-time data streams). IMERG output will be illustrated using early test data, including the variety of supporting fields, such as the merged-microwave and infrared estimates, and the precipitation type. We end by considering recent changes in input data specifications, the transition from TRMM-based calibration to GPM-based, and further "Day 2" development.

A single mitochondrial haplotype and nuclear genetic differentiation in sympatric colour morphs of a riverine cichlid fish.

PubMed

Koblmüller, S; Sefc, K M; Duftner, N; Katongo, C; Tomljanovic, T; Sturmbauer, C

2008-01-01

Some of the diversity of lacustrine cichlid fishes has been ascribed to sympatric divergence, whereas diversification in rivers is generally driven by vicariance and geographic isolation. In the riverine Pseudocrenilabrus philander species complex, several morphologically highly distinct populations are restricted to particular river systems, sinkholes and springs in southern Africa. One of these populations consists of a prevalent yellow morph in sympatry with a less frequent blue morph, and no individuals bear intermediate phenotypes. Genetic variation in microsatellites and AFLP markers was very low in both morphs and one single mtDNA haplotype was fixed in all samples, indicating a very young evolutionary age and small effective population size. Nevertheless, the nuclear markers detected low but significant differentiation between the two morphs. The data suggest recent and perhaps sympatric divergence in the riverine habitat.

Centrifugal partition chromatography: A preparative tool for isolation and purification of xylindein from Chlorociboria aeruginosa.

PubMed

Boonloed, Anukul; Weber, Genevieve L; Ramzy, Kelly M; Dias, Veronica R; Remcho, Vincent T

2016-12-23

A centrifugal partition chromatography (CPC) method was developed for the preparative-scale isolation and purification of xylindein from the wood-staining fungi, Chlorociboria aeruginosa. Xylindein, a blue-green pigment naturally secreted from the hyphae and fruiting bodies of the fungus, has great value in the decorative wood industry and textile coloration. Xylindein has great potential for use as a fluorescent labeling agent as well as in organic semiconductor applications. However, a primary limitation of xylindein is its poor solubility in most common HPLC solvents. Consequently, it is arduous to purify using preparative liquid chromatography or solid-phase extraction (SPE). Support-free, liquid-liquid chromatographic methods, including CPC, where solutes are separated based on their different distribution coefficients (K D ) between two immiscible solvent systems, are promising alternatives for the purification of the compound on a preparative scale. In this work, a new biphasic solvent system suitable for CPC separation of xylindein was developed. Various groups of solvents were assessed for their suitability as xylindein extractants. A new solvent system suitable for CPC separation of xylindein, composed of heptane/THF/MEK/acetonitrile/acetic acid/water, was developed. This solvent system yielded a K D value for xylindein of 1.54±0.04, as determined by HPLC (n=3). The compositions of the upper phase and lower phase of the solvent system were determined by Heteronuclear Single Quantum Correlation (HSQC) NMR and proton NMR. A CPC system, equipped with a fraction collector, was used for the isolation of xylindein from crude extracts. The xylindein fractions isolated by the CPC were then analyzed using HPLC and presented as a fractogram. Based on the CPC fractogram, the purified xylindein fractions were achieved after 30min CPC separation time, yielding 71% extraction efficiency. The developed CPC method allowed for isolation of this naturally sourced xylindein in amounts suitable for further study. Copyright © 2016 Elsevier B.V. All rights reserved.

Numerical and Experimental Validation of the Optimization Methodologies for a Wing-Tip Structure Equipped with Conventional and Morphing Ailerons =

NASA Astrophysics Data System (ADS)

Koreanschi, Andreea

In order to answer the problem of 'how to reduce the aerospace industry's environment footprint?' new morphing technologies were developed. These technologies were aimed at reducing the aircraft's fuel consumption through reduction of the wing drag. The morphing concept used in the present research consists of replacing the conventional aluminium upper surface of the wing with a flexible composite skin for morphing abilities. For the ATR-42 'Morphing wing' project, the wing models were manufactured entirely from composite materials and the morphing region was optimized for flexibility. In this project two rigid wing models and an active morphing wing model were designed, manufactured and wind tunnel tested. For the CRIAQ MDO 505 project, a full scale wing-tip equipped with two types of ailerons, conventional and morphing, was designed, optimized, manufactured, bench and wind tunnel tested. The morphing concept was applied on a real wing internal structure and incorporated aerodynamic, structural and control constraints specific to a multidisciplinary approach. Numerical optimization, aerodynamic analysis and experimental validation were performed for both the CRIAQ MDO 505 full scale wing-tip demonstrator and the ATR-42 reduced scale wing models. In order to improve the aerodynamic performances of the ATR-42 and CRIAQ MDO 505 wing airfoils, three global optimization algorithms were developed, tested and compared. The three algorithms were: the genetic algorithm, the artificial bee colony and the gradient descent. The algorithms were coupled with the two-dimensional aerodynamic solver XFoil. XFoil is known for its rapid convergence, robustness and use of the semi-empirical e n method for determining the position of the flow transition from laminar to turbulent. Based on the performance comparison between the algorithms, the genetic algorithm was chosen for the optimization of the ATR-42 and CRIAQ MDO 505 wing airfoils. The optimization algorithm was improved during the CRIAQ MDO 505 project for convergence speed by introducing a two-step cross-over function. Structural constraints were introduced in the algorithm at each aero-structural optimization interaction, allowing a better manipulation of the algorithm and giving it more capabilities of morphing combinations. The CRIAQ MDO 505 project envisioned a morphing aileron concept for the morphing upper surface wing. For this morphing aileron concept, two optimization methods were developed. The methods used the already developed genetic algorithm and each method had a different design concept. The first method was based on the morphing upper surface concept, using actuation points to achieve the desired shape. The second method was based on the hinge rotation concept of the conventional aileron but applied at multiple nodes along the aileron camber to achieve the desired shape. Both methods were constrained by manufacturing and aerodynamic requirements. The purpose of the morphing aileron methods was to obtain an aileron shape with a smoother pressure distribution gradient during deflection than the conventional aileron. The aerodynamic optimization results were used for the structural optimization and design of the wing, particularly the flexible composite skin. Due to the structural changes performed on the initial wing-tip structure, an aeroelastic behaviour analysis, more specific on flutter phenomenon, was performed. The analyses were done to ensure the structural integrity of the wing-tip demonstrator during wind tunnel tests. Three wind tunnel tests were performed for the CRIAQ MDO 505 wing-tip demonstrator at the IAR-NRC subsonic wind tunnel facility in Ottawa. The first two tests were performed for the wing-tip equipped with conventional aileron. The purpose of these tests was to validate the control system designed for the morphing upper surface, the numerical optimization and aerodynamic analysis and to evaluate the optimization efficiency on the boundary layer behaviour and the wing drag. The third set of wind tunnel tests was performed on the wing-tip equipped with a morphing aileron. The purpose of this test was to evaluate the performances of the morphing aileron, in conjunction with the active morphing upper surface, and their effect on the lift, drag and boundary layer behaviour. Transition data, obtained from Infrared Thermography, and pressure data, extracted from Kulite and pressure taps recordings, were used to validate the numerical optimization and aerodynamic performances of the wing-tip demonstrator. A set of wind tunnel tests was performed on the ATR-42 rigid wing models at the Price-Paidoussis subsonic wind tunnel at Ecole de technologie Superieure. The results from the pressure taps recordings were used to validate the numerical optimization. A second derivative of the pressure distribution method was applied to evaluate the transition region on the upper surface of the wing models for comparison with the numerical transition values. (Abstract shortened by ProQuest.).

Morphing hull implementation for unmanned underwater vehicles

NASA Astrophysics Data System (ADS)

Miller, Timothy F.; Gandhi, Farhan; Rufino, Russell J.

2013-11-01

There has been much interest and work in the area of morphing aircraft since the 1980s. Morphing could also potentially benefit unmanned underwater vehicles (UUVs). The current paper envisions a UUV with an interior pressure hull and a variable diameter outer flexible hull with fuel stored in the annulus between, and presents a mechanism to realize diameter change of the outer hull. The outer hull diameter of UUVs designed for very long endurance/range could be progressively reduced as fuel was consumed, thereby reducing drag and further increasing endurance and range capability. Diameter morphing could also be advantageous for compact storage of UUVs. A prototype is fabricated to represent an axial section of such a morphing diameter UUV. Diameter change is achieved using eight morphing trusses arranged equidistant around the circumference of the representative interior rigid hull. Each morphing truss has a lower rail (attached to the rigid hull) and an upper rail with V-linkages between, at either ends of the rail. Horizontal motion of the feet of the V-linkages (sliding in the lower rail) results in vertical motion of the upper rail which in turn produces diameter change of the outer hull. For the prototype built and tested, a 63% increase in outer diameter from 12.75″ to 20.75″ was achieved. The introduction of a stretched latex representative flexible skin around the outer rails increased actuation force requirement and led to a propensity for the wheel-in-track sliders in the morphing truss to bind. It is anticipated that this could be overcome with higher precision manufacturing. In addition to symmetric actuation of the morphing trusses resulting in diameter change, the paper also shows that with asymmetric actuation the hull cross-section shape can be changed (for example, from a circular section for underwater operation to a V-section for surface operations).

Perspectives on Highly Adaptive or Morphing Aircraft

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria R.; Vicroy, Dan D.; Busan, Ronald C.; Hahn, Andrew S.

2009-01-01

The ability to adapt to different flight conditions has been fundamental to aircraft design since the Wright Brothers first flight. Over a hundred years later, unconventional aircraft adaptability, often called aircraft morphing has become a topic of considerable renewed interest. In the past two decades, this interest has been largely fuelled by advancements in multi-functional or smart materials and structures. However, highly adaptive or morphing aircraft is certainly a cross-discipline challenge that stimulates a wide range of design possibilities. This paper will review some of the history of morphing aircraft including recent research programs and discuss some perspectives on this work.

Electrospun Nanofibrous P(DLLA-CL) Balloons as Calcium Phosphate Cement Filled Containers for Bone Repair: in Vitro and in Vivo Studies.

PubMed

Liu, Xunwei; Wei, Daixu; Zhong, Jian; Ma, Mengjia; Zhou, Juan; Peng, Xiangtao; Ye, Yong; Sun, Gang; He, Dannong

2015-08-26

The spinal surgeon community has expressed significant interest in applying calcium phosphate cement (CPC) for the treatment of vertebral compression fractures (VCFs) and minimizing its disadvantages, such as its water-induced collapsibility and poor mechanical properties, limiting its clinical use. In this work, novel biodegradable electrospun nanofibrous poly(d,l-lactic acid-ϵ-caprolactone) balloons (ENPBs) were prepared, and the separation, pressure, degradation, and new bone formation behaviors of the ENPBs when used as CPC-filled containers in vitro and in vivo were systematically analyzed and compared. CPC could be separated from surrounding bone tissues by ENPBs in vitro and in vivo. ENPB-CPCs (ENPBs serving as CPC-filled containers) exerted pressure on the surrounding bone microenvironment, which was enough to crush trabecular bone. Compared with the CPC implantation, ENPB-CPCs delayed the degradation of CPC (i.e., its water-induced collapsilibity). Finally, possible mechanisms behind the in vivo effects caused by ENPB-CPCs implanted into rabbit thighbones and pig vertebrae were proposed. This work suggests that ENPBs can be potentially applied as CPC-filled containers in vivo and provides an experimental basis for the clinical application of ENPBs for the treatment of VCFs. In addition, this work will be of benefit to the development of polymer-based medical implants in the future.

Finding the optimal shape of the leading-and-trailing car of a high-speed train using design-by-morphing

NASA Astrophysics Data System (ADS)

Oh, Sahuck; Jiang, Chung-Hsiang; Jiang, Chiyu; Marcus, Philip S.

2017-10-01

We present a new, general design method, called design-by-morphing for an object whose performance is determined by its shape due to hydrodynamic, aerodynamic, structural, or thermal requirements. To illustrate the method, we design a new leading-and-trailing car of a train by morphing existing, baseline leading-and-trailing cars to minimize the drag. In design-by-morphing, the morphing is done by representing the shapes with polygonal meshes and spectrally with a truncated series of spherical harmonics. The optimal design is found by computing the optimal weights of each of the baseline shapes so that the morphed shape has minimum drag. As a result of optimization, we found that with only two baseline trains that mimic current high-speed trains with low drag that the drag of the optimal train is reduced by 8.04% with respect to the baseline train with the smaller drag. When we repeat the optimization by adding a third baseline train that under-performs compared to the other baseline train, the drag of the new optimal train is reduced by 13.46% . This finding shows that bad examples of design are as useful as good examples in determining an optimal design. We show that design-by-morphing can be extended to many engineering problems in which the performance of an object depends on its shape.

Finding the optimal shape of the leading-and-trailing car of a high-speed train using design-by-morphing

NASA Astrophysics Data System (ADS)

Oh, Sahuck; Jiang, Chung-Hsiang; Jiang, Chiyu; Marcus, Philip S.

2018-07-01

We present a new, general design method, called design-by-morphing for an object whose performance is determined by its shape due to hydrodynamic, aerodynamic, structural, or thermal requirements. To illustrate the method, we design a new leading-and-trailing car of a train by morphing existing, baseline leading-and-trailing cars to minimize the drag. In design-by-morphing, the morphing is done by representing the shapes with polygonal meshes and spectrally with a truncated series of spherical harmonics. The optimal design is found by computing the optimal weights of each of the baseline shapes so that the morphed shape has minimum drag. As a result of optimization, we found that with only two baseline trains that mimic current high-speed trains with low drag that the drag of the optimal train is reduced by 8.04% with respect to the baseline train with the smaller drag. When we repeat the optimization by adding a third baseline train that under-performs compared to the other baseline train, the drag of the new optimal train is reduced by 13.46%. This finding shows that bad examples of design are as useful as good examples in determining an optimal design. We show that design-by-morphing can be extended to many engineering problems in which the performance of an object depends on its shape.

Life history variation among four lake trout morphs at Isle Royale, Lake Superior

USGS Publications Warehouse

Hansen, Michael J.; Nate, Nancy A.; Muir, Andrew M.; Bronte, Charles R.; Zimmerman, Mara S.; Krueger, Charles C.

2016-01-01

Life history traits were compared among four morphs of lake trout at Isle Royale, Lake Superior. Of 738 lake trout caught at Isle Royale, 701 were assigned to a morph (119 humpers, 160 leans, 85 redfins, and 337 siscowets) using a combination of statistical analysis of head and body shape and visual assignment. On average, redfins were longer (544 mm), heavier (1,481 g), heavier at length (Wr = 94), more buoyant, and older (22 years) than siscowets (519 mm; 1,221 g; 90; 19 years), leans (479 mm; 854 g; 82; 13 years), and humpers (443 mm; 697 g; 87; 17 years). On average, leans grew from a younger age at length = 0 and shorter length at age = 0, at a faster early growth rate to a longer asymptotic length than the other three morphs, while redfins grew at a slower instantaneous rate and humpers grew to a shorter asymptotic length than other morphs. On average, leans were longer (562 mm) and older (15 years) at 50% maturity than redfins (427 mm, 12 years), siscowets (401 mm, 11 years), or humpers (394 mm, 13 years). Life history parameters did not differ between males and females within each morph. We conclude that differences in life history attributes of lean, humper, redfin, and siscowet morphs of lake trout are consistent with differential habitat use in waters around Isle Royale, Lake Superior.

Climate Prediction Center - Monitoring East Pacific Hurricane Potential

Science.gov Websites

Organization Search Go Search the CPC Go About Us Our Mission Who We Are Contact Us CPC Information CPC Web Team USA.gov is the U.S. Government's official Web portal to all Federal, state and local government Web resources and services. HOME > Monitoring and Data > Monitoring East Pacific Hurricane

CPC - Monitoring & Data: Rest of the World Climate Data

Science.gov Websites

produces maps and time series for precipitation and surface temperatures for Africa, Asia, Europe, South - The CPC monitors weather and climate in real time with the aid of satellite animations, conventional , intraseasonal, seasonal and annual time scales are highlighted. The CPC also collects time series of accumulated

Molecular cloning of the alpha subunit of complement component C8 (CpC8α) of whitespotted bamboo shark (Chiloscyllium plagiosum).

PubMed

Wang, Ying; Zhang, Mengmeng; Wang, Conghui; Ye, Boping; Hua, Zichun

2013-12-01

Complement-mediated cytolysis is the important effect of immune response, which results from the assembly of terminal complement components (C5b-9). Among them, α subunit of C8 (C8α) is the first protein that traverses the lipid bilayer, and then initiates the recruitment of C9 molecules to form pore on target membranes. In this article, a full-length cDNA of C8α (CpC8α) is identified from the whitespotted bamboo shark (Chiloscyllium plagiosum) by RACE. The CpC8α cDNA is 2183 bp in length, encoding a protein of 591 amino acids. The deduced CpC8α exhibits 89%, 49% and 44% identity with nurse shark, frog and human orthologs, respectively. Sequence alignment indicates that the C8α is well conserved during the evolution process from sharks to mammals, with the same modular architecture as well as the identical cysteine composition in the mature protein. Phylogenetic analysis places CpC8α and nurse shark C8α in cartilaginous fish clade, in parallel with the teleost taxa, to form the C8α cluster with higher vertebrates. Hydrophobicity analysis also indicates a similar hydrophobicity of CpC8α to mammals. Finally, expression analysis revealed CpC8α transcripts were constitutively highly expressed in shark liver, with much less expression in other tissues. The well conserved structure and properties suggests an analogous function of CpC8α to mammalian C8α, though it remains to be confirmed by further study. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hydrogel fibers encapsulating hiPSC-MSCs, hESC-MSCs and hUCMSCs in injectable calcium phosphate scaffold for bone tissue engineering

PubMed Central

Wang, Lin; Wang, Ping; Weir, Michael D.; Reynolds, Mark A.; Zhao, Liang; Xu, Hockin H. K.

2016-01-01

Human induced pluripotent stem cells (hiPSCs), human embryonic stem cells (hESCs) and human umbilical cord MSCs (hUCMSCs) are exciting cell sources for use in regenerative medicine. There has been no report on long hydrogel fibers encapsulating stem cells inside injectable calcium phosphate cement (CPC) scaffold for bone tissue engineering. The objectives of this study were to: (1) develop a novel injectable CPC construct containing hydrogel fibers encapsulating cells for bone engineering, and (2) investigate and compare cell viability, proliferation and osteogenic differentiation of hiPSC-MSCs, hESC-MSCs and hUCMSCs in injectable CPC. The stem cell-encapsulating pastes were fully injectable under a small injection force, and the injection did not harm the cells, compared to cells without injection (p > 0.1). Mechanical properties of stem cell-CPC construct were much higher than previous injectable polymers and hydrogels for cell delivery. hiPSC-MSCs, hESC-MSCs and hUCMSCs in hydrogel fibers in CPC had excellent proliferation and osteogenic differentiation. All three cells yielded high alkaline phosphatase, runt-related transcription factor, collagen I, and osteocalcin expressions (mean ± sd; n = 6). Cell-synthesized minerals increased substantially with time (p < 0.05), with no significant difference among the three types of cells (p > 0.1). Mineralization by hiPSC-MSCs, hESC-MSCs and hUCMSCs in CPC at 14 d was 13-fold that at 1 d. In conclusion, all three types of cells (hiPSC-MSCs, hESC-MSCs and hUCMSCs) in CPC scaffold showed high potential for bone tissue engineering, and the novel injectable CPC construct with cell-encapsulating hydrogel fibers is promising to enhance bone regeneration in dental, craniofacial and orthopedic applications. PMID:27811389

Chemical Discrimination of Cortex Phellodendri amurensis and Cortex Phellodendri chinensis by Multivariate Analysis Approach.

PubMed

Sun, Hui; Wang, Huiyu; Zhang, Aihua; Yan, Guangli; Han, Ying; Li, Yuan; Wu, Xiuhong; Meng, Xiangcai; Wang, Xijun

2016-01-01

As herbal medicines have an important position in health care systems worldwide, their current assessment, and quality control are a major bottleneck. Cortex Phellodendri chinensis (CPC) and Cortex Phellodendri amurensis (CPA) are widely used in China, however, how to identify species of CPA and CPC has become urgent. In this study, multivariate analysis approach was performed to the investigation of chemical discrimination of CPA and CPC. Principal component analysis showed that two herbs could be separated clearly. The chemical markers such as berberine, palmatine, phellodendrine, magnoflorine, obacunone, and obaculactone were identified through the orthogonal partial least squared discriminant analysis, and were identified tentatively by the accurate mass of quadruple-time-of-flight mass spectrometry. A total of 29 components can be used as the chemical markers for discrimination of CPA and CPC. Of them, phellodenrine is significantly higher in CPC than that of CPA, whereas obacunone and obaculactone are significantly higher in CPA than that of CPC. The present study proves that multivariate analysis approach based chemical analysis greatly contributes to the investigation of CPA and CPC, and showed that the identified chemical markers as a whole should be used to discriminate the two herbal medicines, and simultaneously the results also provided chemical information for their quality assessment. Multivariate analysis approach was performed to the investigate the herbal medicineThe chemical markers were identified through multivariate analysis approachA total of 29 components can be used as the chemical markers. UPLC-Q/TOF-MS-based multivariate analysis method for the herbal medicine samples Abbreviations used: CPC: Cortex Phellodendri chinensis, CPA: Cortex Phellodendri amurensis, PCA: Principal component analysis, OPLS-DA: Orthogonal partial least squares discriminant analysis, BPI: Base peaks ion intensity.

In Vivo Release of Vancomycin from Calcium Phosphate Cement.

PubMed

Uchida, Kentaro; Sugo, Ken; Nakajima, Takehiko; Nakawaki, Mitsufumi; Takano, Shotaro; Nagura, Naoshige; Takaso, Masashi; Urabe, Ken

2018-01-01

Calcium phosphate cement (CPC) has good release efficiency and has therefore been used as a drug delivery system for postoperative infection. The release profile of CPC has mainly been evaluated by in vitro studies, which are carried out by immersing test specimens in a relatively large amount of solvent. However, it remains unclear whether antibiotic-impregnated CPC has sufficient clinical effects and release in vivo . We examined the in vivo release profile of CPC impregnated with vancomycin (VCM) and compared this with that of polymethylmethacrylate (PMMA) cement. To evaluate the release profile in vitro , the test specimens were immersed in 10 mL sterile phosphate-buffered saline per gram of test specimen and incubated at 37°C for 56 days in triplicate. For in vivo experiments, the test specimens were implanted between the fascia and muscle of the femur of rats. Residual VCM was extracted from the removed test specimens to determine the amount of VCM released into rat tissues. CPC released more VCM over a longer duration than PMMA in vitro . Released levels of VCM from CPC/VCM in vivo were 3.4-fold, 5.0-fold, and 8.6-fold greater on days 1, 7, and 28, respectively, than those released on the corresponding days from PMMA/VCM and were drastically greater on day 56 due to inefficient release from PMMA/VCM. The amount of VCM released from CPC and PMMA was much higher than the minimum inhibitory concentration (1.56  μ g) and lower than the detection limit, respectively. Our findings suggest that CPC is a suitable material for releasing antibiotics for local action against established postoperative infection.

Antioxidant Machinery Differs between Melanic and Light Nestlings of Two Polymorphic Raptors

PubMed Central

Galván, Ismael; Gangoso, Laura; Grande, Juan M.; Negro, Juan J.; Rodríguez, Airam; Figuerola, Jordi; Alonso-Alvarez, Carlos

2010-01-01

Colour polymorphism results from the expression of multiallelic genes generating phenotypes with very distinctive colourations. Most colour polymorphisms are due to differences in the type or amount of melanins present in each morph, which also differ in several behavioural, morphometric and physiological attributes. Melanin-based colour morphs could also differ in the levels of glutathione (GSH), a key intracellular antioxidant, because of the role of this molecule in melanogenesis. As GSH inhibits the synthesis of eumelanin (i.e. the darkest melanin form), individuals of darker morphs are expected to have lower GSH levels than those of lighter morphs. We tested this prediction in nestlings of two polymorphic raptors, the booted eagle Hieraaetus pennatus and the Eleonora's falcon Falco eleonorae, both of which occur in two morphs differing in the extent of eumelanic plumage. As expected, melanic booted eagle nestlings had lower blood GSH levels than light morph eagle nestlings. In the Eleonora's falcon, however, melanic nestlings only had lower GSH levels after controlling for the levels of other antioxidants. We also found that melanic female eagle nestlings had higher levels of antioxidants other than GSH and were in better body condition than light female eagle nestlings. These findings suggest an adaptive response of melanic nestlings to compensate for reduced GSH levels. Nevertheless, these associations were not found in falcons, indicating species-specific particularities in antioxidant machinery. Our results are consistent with previous work revealing the importance of GSH on the expression of melanic characters that show continuous variation, and suggest that this pathway also applies to discrete colour morphs. We suggest that the need to maintain low GSH levels for eumelanogenesis in dark morph individuals may represent a physiological constraint that helps regulate the evolution and maintenance of polymorphisms. PMID:20976228

Antioxidant machinery differs between melanic and light nestlings of two polymorphic raptors.

PubMed

Galván, Ismael; Gangoso, Laura; Grande, Juan M; Negro, Juan J; Rodríguez, Airam; Figuerola, Jordi; Alonso-Alvarez, Carlos

2010-10-14

Colour polymorphism results from the expression of multiallelic genes generating phenotypes with very distinctive colourations. Most colour polymorphisms are due to differences in the type or amount of melanins present in each morph, which also differ in several behavioural, morphometric and physiological attributes. Melanin-based colour morphs could also differ in the levels of glutathione (GSH), a key intracellular antioxidant, because of the role of this molecule in melanogenesis. As GSH inhibits the synthesis of eumelanin (i.e. the darkest melanin form), individuals of darker morphs are expected to have lower GSH levels than those of lighter morphs. We tested this prediction in nestlings of two polymorphic raptors, the booted eagle Hieraaetus pennatus and the Eleonora's falcon Falco eleonorae, both of which occur in two morphs differing in the extent of eumelanic plumage. As expected, melanic booted eagle nestlings had lower blood GSH levels than light morph eagle nestlings. In the Eleonora's falcon, however, melanic nestlings only had lower GSH levels after controlling for the levels of other antioxidants. We also found that melanic female eagle nestlings had higher levels of antioxidants other than GSH and were in better body condition than light female eagle nestlings. These findings suggest an adaptive response of melanic nestlings to compensate for reduced GSH levels. Nevertheless, these associations were not found in falcons, indicating species-specific particularities in antioxidant machinery. Our results are consistent with previous work revealing the importance of GSH on the expression of melanic characters that show continuous variation, and suggest that this pathway also applies to discrete colour morphs. We suggest that the need to maintain low GSH levels for eumelanogenesis in dark morph individuals may represent a physiological constraint that helps regulate the evolution and maintenance of polymorphisms.

CAPRICE positively regulates stomatal formation in the Arabidopsis hypocotyl

PubMed Central

2008-01-01

In the Arabidopsis hypocotyl, stomata develop only from a set of epidermal cell files. Previous studies have identified several negative regulators of stomata formation. Such regulators also trigger non-hair cell fate in the root. Here, it is shown that TOO MANY MOUTHS (TMM) positively regulates CAPRICE (CPC) expression in differentiating stomaless-forming cell files, and that the CPC protein might move to the nucleus of neighbouring stoma-forming cells, where it promotes stomata formation in a redundant manner with TRIPTYCHON (TRY). Unexpectedly, the CPC protein was also localized in the nucleus and peripheral cytoplasm of hypocotyl fully differentiated epidermal cells, suggesting that CPC plays an additional role to those related to stomata formation. These results identify CPC and TRY as positive regulators of stomata formation in the embryonic stem, which increases the similarity between the genetic control of root hair and stoma cell fate determination. PMID:19513241

Femtosecond laser micromachining of compound parabolic concentrator fiber tipped glucose sensors.

PubMed

Hassan, Hafeez Ul; Lacraz, Amédée; Kalli, Kyriacos; Bang, Ole

2017-03-01

We report on highly accurate femtosecond (fs) laser micromachining of a compound parabolic concentrator (CPC) fiber tip on a polymer optical fiber (POF). The accuracy is reflected in an unprecedented correspondence between the numerically predicted and experimentally found improvement in fluorescence pickup efficiency of a Förster resonance energy transfer-based POF glucose sensor. A Zemax model of the CPC-tipped sensor predicts an optimal improvement of a factor of 3.96 compared to the sensor with a plane-cut fiber tip. The fs laser micromachined CPC tip showed an increase of a factor of 3.5, which is only 11.6% from the predicted value. Earlier state-of-the-art fabrication of the CPC-shaped tip by fiber tapering was of so poor quality that the actual improvement was 43% lower than the predicted improvement of the ideal CPC shape.

Femtosecond laser micromachining of compound parabolic concentrator fiber tipped glucose sensors

NASA Astrophysics Data System (ADS)

Hassan, Hafeez Ul; Lacraz, Amédée; Kalli, Kyriacos; Bang, Ole

2017-03-01

We report on highly accurate femtosecond (fs) laser micromachining of a compound parabolic concentrator (CPC) fiber tip on a polymer optical fiber (POF). The accuracy is reflected in an unprecedented correspondence between the numerically predicted and experimentally found improvement in fluorescence pickup efficiency of a Förster resonance energy transfer-based POF glucose sensor. A Zemax model of the CPC-tipped sensor predicts an optimal improvement of a factor of 3.96 compared to the sensor with a plane-cut fiber tip. The fs laser micromachined CPC tip showed an increase of a factor of 3.5, which is only 11.6% from the predicted value. Earlier state-of-the-art fabrication of the CPC-shaped tip by fiber tapering was of so poor quality that the actual improvement was 43% lower than the predicted improvement of the ideal CPC shape.

Morphing unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Gomez, Juan Carlos; Garcia, Ephrahim

2011-10-01

Research on aircraft morphing has exploded in recent years. The motivation and driving force behind this has been to find new and novel ways to increase the capabilities of aircraft. Materials advancements have helped to increase possibilities with respect to actuation and, hence, a diversity of concepts and unimagined capabilities. The expanded role of unmanned aerial vehicles (UAVs) has provided an ideal platform for exploring these emergent morphing concepts since at this scale a greater amount of risk can be taken, as well as having more manageable fabrication and cost requirements. This review focuses on presenting the role UAVs have in morphing research by giving an overview of the UAV morphing concepts, designs, and technologies described in the literature. A presentation of quantitative information as well as a discussion of technical issues is given where possible to begin gaining some insight into the overall assessment and performance of these technologies.

Design and analysis of morphing wing based on SMP composite

NASA Astrophysics Data System (ADS)

Yu, Kai; Yin, Weilong; Sun, Shouhua; Liu, Yanju; Leng, Jinsong

2009-03-01

A new concept of a morphing wing based on shape memory polymer (SMP) and its reinforced composites is proposed in this paper. SMP used in this study is a thermoset styrene-based resin in contrast to normal thermoplastic SMP. During heating, the wing curled on the aircraft can be deployed, providing main lift for a morphing aircraft to realize the stable flight. Aerodynamic characteristics of the deployed morphing wing are calculated by using CFD software. The static deformation of the wing under the air loads is also analyzed by using the finite element method. The results show that the used SMP material can provide enough strength and stiffness for the application. Finally, preliminary testing is conducted to investigate the recovery performances of SMP and its reinforced composites. During the test, the deployment and the wind-resistant ability of the morphing wing are dramatically improved by adding reinforced phase to the SMP.

Attention: Page has moved

Science.gov Websites

Skip Navigation Links www.nws.noaa.gov NOAA logo - Click to go to the NOAA home page National Weather Service NWS logo - Click to go to the NWS home page Climate Prediction Center Site Map News Organization Search All NWS Search Go CPC Search CPC search Go About Us Our Mission Who We Are Contact Us CPC

Compound parabolic concentrator probe for efficient light collection in spectroscopy of biological tissue

NASA Astrophysics Data System (ADS)

Tanaka, Kazunori; Pacheco, Marcos T. T.; Brennan, James F., III; Itzkan, Irving; Berger, Andrew J.; Dasari, Ramachandra R.; Feld, Michael S.

1996-02-01

We describe a compound parabolic concentrator (CPC)-based probe for enhanced signal collection in the spectroscopy of biological tissues. Theoretical considerations governing signal enhancement compared with conventional collection methods are given. A ray-tracing program was used to analyze the throughput of CPC's with shape deviations and surface imperfections. A modified CPC shape with 99% throughput was discovered. A 4.4-mm-long CPC was manufactured and incorporated into an optical fiber-based near-infrared Raman spectrometer system. For human tissue samples, light collection was enhanced by a factor of 7 compared with collection with 0.29-NA optical fibers.

Effectiveness of solar disinfection using batch reactors with non-imaging aluminium reflectors under real conditions: Natural well-water and solar light.

PubMed

Navntoft, C; Ubomba-Jaswa, E; McGuigan, K G; Fernández-Ibáñez, P

2008-12-11

Inactivation kinetics are reported for suspensions of Escherichia coli in well-water using compound parabolic collector (CPC) mirrors to enhance the efficiency of solar disinfection (SODIS) for batch reactors under real, solar radiation (cloudy and cloudless) conditions. On clear days, the system with CPC reflectors achieved complete inactivation (more than 5-log unit reduction in bacterial population to below the detection limit of 4CFU/mL) one hour sooner than the system fitted with no CPC. On cloudy days, only systems fitted with CPCs achieved complete inactivation. Degradation of the mirrors under field conditions was also evaluated. The reflectivity of CPC systems that had been in use outdoors for at least 3 years deteriorated in a non-homogeneous fashion. Reflectivity values for these older systems were found to vary between 27% and 72% compared to uniform values of 87% for new CPC systems. The use of CPC has been proven to be a good technological enhancement to inactivate bacteria under real conditions in clear and cloudy days. A comparison between enhancing optics and thermal effect is also discussed.

Medical Application of Spirulina platensis Derived C-Phycocyanin

PubMed Central

Liu, Qian; Huang, Yinghong; Zhang, Ronghua; Cai, Tiange; Cai, Yu

2016-01-01

Along with the development of marine biological pharmaceutical research, high-effective and low-toxic drugs and functional foods isolated from marine organisms have become a new field of pharmacy and bromatology. The pharmacological actions, such as anti-inflammation, antioxidation, antitumor, immunological enhancement, and hepatorenal protection of C-phycocyanin (C-PC) from Spirulina platensis, have been reported, and C-PC has important value of development and utilization either as drug or as functional food. There are many researches about the various pharmacological actions and mechanisms of C-PC, but related reports are only to some extent integrated deeply and accurately enough, which put some limitations to the further application of C-PC in medicine. Particularly, with the improvement of living standards and attention to health issues, C-PC being a functional food is preferred by more and more people. C-PC is easy to get, safe, and nontoxic; thus, it has a great potential of research and development as a drug or functional food. Here, the separation and purification, physicochemical properties, physiological and pharmacological activities, safety, and some applications are reviewed to provide relevant basis for the development of natural medicine and applied products. PMID:27293463

Lighting up Protons with MorphFl, a Fluorescein-Morpholine Dyad: An Experiment for the Organic Laboratory

ERIC Educational Resources Information Center

Miller, Tyson A.; Spangler, Michael; Burdette, Shawn C.

2011-01-01

A two-period organic laboratory experiment that includes fluorescence sensing is presented. The pH-sensitive sensor MorphFl is prepared using a Mannich reaction between a fluorescein derivative and the iminium ion of morpholine. During the first laboratory, students prepare MorphFl. The second session begins with characterizing the sensor using…

On the Role of Individual Items in Recognition Memory and Metacognition: Challenges for Signal Detection Theory

ERIC Educational Resources Information Center

Busey, Thomas A.; Arici, Anne

2009-01-01

The authors tested the role of individual items in recognition memory using a forced-choice paradigm with face stimuli. They constructed distractor stimuli using morphing procedures that were similar to two parent faces and then compared a studied morph against an unstudied morph that was similar to two studied parents. The similarity of the…

Contour-based image warping

NASA Astrophysics Data System (ADS)

Chan, Kwai H.; Lau, Rynson W.

1996-09-01

Image warping concerns about transforming an image from one spatial coordinate to another. It is widely used for the vidual effect of deforming and morphing images in the film industry. A number of warping techniques have been introduced, which are mainly based on the corresponding pair mapping of feature points, feature vectors or feature patches (mostly triangular or quadrilateral). However, very often warping of an image object with an arbitrary shape is required. This requires a warping technique which is based on boundary contour instead of feature points or feature line-vectors. In addition, when feature point or feature vector based techniques are used, approximation of the object boundary by using point or vectors is required. In this case, the matching process of the corresponding pairs will be very time consuming if a fine approximation is required. In this paper, we propose a contour-based warping technique for warping image objects with arbitrary shapes. The novel idea of the new method is the introduction of mathematical morphology to allow a more flexible control of image warping. Two morphological operators are used as contour determinators. The erosion operator is used to warp image contents which are inside a user specified contour while the dilation operation is used to warp image contents which are outside of the contour. This new method is proposed to assist further development of a semi-automatic motion morphing system when accompanied with robust feature extractors such as deformable template or active contour model.

Interobserver repeatability of measurements on computed tomography images of lax canine hip joints from youth to maturity.

PubMed

Lopez, Mandi J; Davis, Kechia M; Jeffrey-Borger, Susan L; Markel, Mark D; Rettenmund, Christy

2009-12-01

To determine interobserver repeatability of measurements on computed tomography (CT) images of lax canine hip joints at different ages and in the presence of degenerative joint disease at maturity. Longitudinal observational investigation. Sibling crossbreed hounds. Pelvic CT was performed at 20, 24, 32, 48, 68, and 104 weeks of age. Measures were performed on 3 contiguous two-dimensional (2D) transverse CT images of both hips at each time point by 3 investigators. Center-edge angle (CEA), horizontal toit externe angle (HTEA), ventral (VASA), dorsal (DASA), and horizontal (HASA) acetabular sector angles, acetabular index (AI), and percent femoral head coverage (CPC) were measured. Interobserver repeatability was quantified with the intraclass correlation coefficient (ICC). Satisfactory repeatability was considered when ICC >or=0.75. DASA, CEA, and CPC were repeatable in all age groups. HASA and HTEA were repeatable for all but 1 time point. At 20 weeks of age, all measures but AI were repeatable, and at 104 weeks of age, DASA, CEA, CPC, and HASA were repeatable. Measures were repeatable in hips with and without degenerative changes with the exceptions of AI and HASA in normal hips and VASA and HTEA in osteoarthritic hips. Most 2D CT measurements examined were repeatable regardless of age or joint disease. Two-dimensional CT measures may augment current techniques for assessing joint changes in lax canine hips.

In vitro and in vivo evaluation of calcium phosphate composite scaffolds containing BMP-VEGF loaded PLGA microspheres for the treatment of avascular necrosis of the femoral head.

PubMed

Zhang, Hao-Xuan; Zhang, Xiu-Ping; Xiao, Gui-Yong; Hou, Yong; Cheng, Lei; Si, Meng; Wang, Shuai-Shuai; Li, Yu-Hua; Nie, Lin

2016-03-01

Avascular necrosis of the femoral head (ANFH) is difficult to treat due to high pressure and hypoxia, and reduced levels of growth factors such as bone morphogenetic protein (BMP), and vascular endothelial growth factor (VEGF). We generated a novel calcium phosphate (CPC) composite scaffold, which contains BMP-VEGF-loaded poly-lactic-co-glycolic acid (PLGA) microspheres (BMP-VEGF-PLGA-CPC). The BMP-VEGF-loaded microspheres have an encapsulation efficiency of 89.15% for BMP, and 78.55% for VEGF. The BMP-VEGF-PLGA-CPC scaffold also demonstrated a porosity of 62% with interconnected porous structures, and pore sizes of 219 μm and compressive strength of 6.60 MPa. Additionally, bone marrow mesenchymal stem cells (BMSCs) were seeded on scaffolds in vitro. Further characterization showed that the BMP-VEGF-PLGA-CPC scaffolds were biocompatible and enhanced osteogenesis and angiogenesis in vitro. Using a rabbit model of ANFH, BMP-VEGF-PLGA-CPC scaffolds were implanted into the bone tunnels of core decompression in the femoral head for 6 and 12 weeks. Radiographic and histological analysis demonstrated that the BMP-VEGF-PLGA-CPC scaffolds exhibited good biocompatibility, and osteogenic and angiogenic activity in vivo. These results indicate that the BMP-VEGF-PLGA-CPC scaffold may improve the therapeutic effect of core decompression surgery and be used as a treatment for ANFH. Copyright © 2015 Elsevier B.V. All rights reserved.

Novel substrate (algal protein) for cultivation of Rhodospirillum rubrum.

PubMed

Vatsala, T M; Rekha, R; Srividhya, R

2011-10-01

Rhodospirillum rubrum was grown under light anaerobic conditions with phycocyanin (C-pc) extracted from Spirulina platensis as the sole source of carbon and nitrogen. When grown under these conditions cellular components like lipids, carbohydrates, protein, carotenoids, bacteriochlorophyll were similar to the one grown with malic acid and ammonium chloride. Growth of R. rubrum increased with increase in concentration of C-pc (200 to 1000 mg/l). R. rubrum also utilized C-pc under dark anaerobic condition. With both malic acid and C-pc as carbon sources C-pc was consumed only after exhaustion of malic acid under light anaerobic condition. No aberration of cell morphology was seen under scanning electron microscope (SEM). R. rubrum utilized both phycocyanobilin and phycoprotein individually as well as in combination. When grown with 1000 mg/l of phycoprotein 450 mg/l of biomass was obtained, and with combination of phycocyanobilin (75 mg/l) and phycoprotein (925 mg/l) 610 mg/l of biomass was obtained. Phycocyanobilin alone did not inhibit the growth of R. rubrum. Utilization of C-pc with protease like activity was observed in plate assay. Protease like activity was also observed as zones around the colonies in plates containing sterilized casein, gelatin and filter sterilized bovine serum albumin. No amino acids were detected in the supernatant when analyzed with ninhydrin. Extracellular protease like activity was highest when C-pc was used as substrate (2.8 U/ml). Intracellular protease like activity was not detected in cell free extracts.

Design and simulation on the morphing composite propeller (Conference Presentation)

NASA Astrophysics Data System (ADS)

Chen, Fanlong; Li, Qinyu; Liu, Liwu; Lan, Xin; Liu, Yanju; Leng, Jinsong

2017-04-01

As one of the most crucial part of the unmanned underwater vehicle (UUV), the composite propeller plays an important role on the UUV's performance. As the composite propeller behaves excellent properties in hydroelastic facet and acoustic suppression, it attracts increasing attentions all over the globe. This paper goes a step further based on this idea, and comes up with a novel concept of "morphing composite propeller" (MCP) to improve the performance of the conventional composite propeller (CCP) to anticipate the improved propeller can perform better to propel the UUV. Based on the new concept, a novel MCP is designed. Each blade of the propeller is assembled with an active rotatable flap (ARF) to change the blade's local camber with flap rotation. Then the transmission mechanism (TM) has been designed and housed in the propeller blade to push the ARF. With the ARF rotating, the UUV can be propelled by different thrusts under certain rotation velocities of the propeller. Based on the design, the Fluent is exploited to analyze the fluid dynamics around the propeller. Finally, based on the design and hydrodynamic analysis, the structural response for the novel morphing composite propeller is calculated. The propeller blade is simplified and layered with composite materials. And the structure response of an MCP is obtained with various rotation angle under the hydrodynamic pressure. This simulation can instruct the design and fabrication techniques of the MCP.

The evolutionary history of colour polymorphism in Ischnura damselflies.

PubMed

Sánchez-Guillén, Rosa A; Cordero-Rivera, Adolfo; Rivas-Torres, Anais; Wellenreuther, Maren; Bybee, Seth; Hansson, Bengt; Velasquez-Vélez, María I; Realpe, Emilio; Chávez-Ríos, Jesús R; Villalobos, Fabricio; Dumont, Henri

2018-05-10

A major challenge in evolutionary biology consists of understanding how genetic and phenotypic variation is created and maintained. In the present study, we investigated the origin(s) and evolutionary patterns of the female-limited colour polymorphism in ischnuran damselflies. These consist of the presence of one to three colour morphs: one androchrome morph with a colouration that is similar to the male, and two gynochrome morphs (infuscans and aurantiaca) with female-specific colouration. We (i) documented the colour and mating system of 44 of the 75 taxa within the genus Ischnura, (ii) reconstructed the evolutionary history of colour and mating system to identify the ancestral state, (iii) evaluated the stability of the colour morph status over time, and (iv) tested for a correlation between colour and mating system. We found that the ances tral female colour of Ischnura was monomorphic and aurantiaca and that colour morph status changed over time; characterised by many gains and losses across the species tree. Our results further showed that colour polymorphism is significantly more frequent among polyandric species, whereas monandric species tend to be monomorphic. Research on some Ischnura species has shown that colour morphs have evolved to reduce male mating harassment, and our finding that the same phenotypic morphs have evolved multiple times (convergent evolution) suggests that several species in this genus might be experiencing similar selective pressures. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Differences in pollination success between local and foreign flower color phenotypes: a translocation experiment with Gentiana lutea (Gentianaceae).

PubMed

Guitián, Javier A; Sobral, Mar; Veiga, Tania; Losada, María; Guitián, Pablo; Guitián, José M

2017-01-01

The adaptive maintenance of flower color variation is frequently attributed to pollinators partly because they preferentially visit certain flower phenotypes. We tested whether Gentiana lutea -which shows a flower color variation (from orange to yellow) in the Cantabrian Mountains range (north of Spain)-is locally adapted to the pollinator community. We transplanted orange-flowering individuals to a population with yellow-flowering individuals and vice versa, in order to assess whether there is a pollination advantage in the local morph by comparing its visitation rate with the foreign morph. Our reciprocal transplant experiment did not show clear local morph advantage in overall visitation rate: local orange flowers received more visits than foreign yellow flowers in the orange population, while both local and foreign flowers received the same visits in the yellow population; thus, there is no evidence of local adaptation in Gentiana lutea to the pollinator assemblage. However, some floral visitor groups (such as Bombus pratorum , B. soroensis ancaricus and B. lapidarius decipiens ) consistently preferred the local morph to the foreign morph whereas others (such as Bombus terrestris ) consistently preferred the foreign morph. We concluded that there is no evidence of local adaptation to the pollinator community in each of the two G. lutea populations studied. The consequences for local adaptation to pollinator on G. lutea flower color would depend on the variation along the Cantabrian Mountains range in morph frequency and pollinator community composition.

Differences in pollination success between local and foreign flower color phenotypes: a translocation experiment with Gentiana lutea (Gentianaceae)

PubMed Central

Sobral, Mar; Veiga, Tania; Guitián, Pablo; Guitián, José M.

2017-01-01

Background The adaptive maintenance of flower color variation is frequently attributed to pollinators partly because they preferentially visit certain flower phenotypes. We tested whether Gentiana lutea—which shows a flower color variation (from orange to yellow) in the Cantabrian Mountains range (north of Spain)—is locally adapted to the pollinator community. Methods We transplanted orange-flowering individuals to a population with yellow-flowering individuals and vice versa, in order to assess whether there is a pollination advantage in the local morph by comparing its visitation rate with the foreign morph. Results Our reciprocal transplant experiment did not show clear local morph advantage in overall visitation rate: local orange flowers received more visits than foreign yellow flowers in the orange population, while both local and foreign flowers received the same visits in the yellow population; thus, there is no evidence of local adaptation in Gentiana lutea to the pollinator assemblage. However, some floral visitor groups (such as Bombus pratorum, B. soroensis ancaricus and B. lapidarius decipiens) consistently preferred the local morph to the foreign morph whereas others (such as Bombus terrestris) consistently preferred the foreign morph. Discussion We concluded that there is no evidence of local adaptation to the pollinator community in each of the two G. lutea populations studied. The consequences for local adaptation to pollinator on G. lutea flower color would depend on the variation along the Cantabrian Mountains range in morph frequency and pollinator community composition. PMID:28194308

Apparent and true ileal and total tract digestibility of fat in canola press-cake or canola oil and effects of increasing dietary fat on amino acid and energy digestibility in growing pigs.

PubMed

Zhou, X; Beltranena, E; Zijlstra, R T

2017-06-01

Digestibility of remaining oil in canola press-cake (CPC) may be lower than that of extracted, liquid canola oil (CO) because oil may be partly entrapped in the CPC matrix. To determine true digestibility of fat in ingredients, endogenous fat losses should be estimated. Dietary fat may interact with digestion of other dietary components. To test these hypotheses, 10 ileal-cannulated pigs (initial BW, 25.4 kg) were fed 10 diets for 8 periods in a 10 × 8 Youden square. A basal diet was formulated based on wheat, barley, and canola meal. The 4 CPC and 4 CO test diets were prepared by replacing identical portion of basal diet with 10%, 20%, 30%, or 40% CPC, or 1.5%, 3.0%, 4.5%, or 6.0% CO, respectively, to match the fat content of CPC diet with CO diet at each fat level. An N-free diet based on corn starch was prepared to measure basal endogenous losses of AA. Apparent total tract digestibility (ATTD) and apparent ileal digestibility (AID) of acid-hydrolyzed ether extract (AEE) were calculated for each diet. True ileal digestibility (TID) and true total tract (TTTD) digestibility of AEE in CPC and CO, and total endogenous losses of AEE were estimated by regressing apparent digestible AEE (g/kg of DMI) against dietary AEE intake (g/kg of DM) at the total tract and distal ileum, respectively. The mean AID and ATTD of AEE in CPC diets were 78.9% and 61.5%, which were lower ( < 0.01) than 81.9% and 63.4% in CO diets. Apparent ileal and total tract digestible AEE content in CPC and CO diets increased linearly ( < 0.01) with increasing AEE intake. Endogenous losses of AEE were greater ( < 0.05) for the total tract than for the ileum (23.4 vs. 9.4 g/kg of DMI). Dietary fat source did not affect ( > 0.05) total tract or ileal endogenous losses of AEE. The TID and TTTD of AEE in CPC were 92.3% and 94.5%, respectively, lower ( < 0.01) than 96.5% and 100% in CO. Increasing dietary inclusion of CO linearly increased ( < 0.001) standardized ileal digestibility (SID) of CP, Lys, Met, Thr, and Trp, and quadratically increased ( < 0.001) the AID and ATTD of energy in the basal part of the test diets. In conclusion, CPC had lower TID and TTTD of AEE than CO. Dietary fat source did not affect endogenous losses of AEE. The lower digestibility of AEE in CPC than in CO indicates that fat digestibility of CPC should be considered to predict its nutritional value accurately. Dietary inclusion of CO may increase digestibility of CP and energy originating from the balance of the diet.

Genetically distinct colour morphs of European perch Perca fluviatilis in Lake Constance differ in susceptibility to macroparasites.

PubMed

Roch, S; Behrmann-Godel, J; Brinker, A

2015-01-21

The unusual yellow-finned morph of European perch Perca fluviatilis found in Lake Constance suffers more severely from macroparasite infections, including the tapeworm Triaenophorus nodulosus and the gill worm Ancyrocephalus percae, than conspecifics elsewhere. Microsatellite analysis of yellow-finned P. fluviatilis and red-finned variant recently discovered in Lake Constance revealed significant genetic differentiation. Red-finned P. fluviatilis and fish with mixed fin colour, suggested backcrosses between red and yellow-finned colour morphs, exhibit better resilience to parasite infection, suggesting that the inability of the yellow-finned morph to reject macroparasites may have a genetic basis. © 2015 The Fisheries Society of the British Isles.

MORPH-II, a software package for the analysis of scanning-electron-micrograph images for the assessment of the fractal dimension of exposed stone surfaces

USGS Publications Warehouse

Mossotti, Victor G.; Eldeeb, A. Raouf

2000-01-01

Turcotte, 1997, and Barton and La Pointe, 1995, have identified many potential uses for the fractal dimension in physicochemical models of surface properties. The image-analysis program described in this report is an extension of the program set MORPH-I (Mossotti and others, 1998), which provided the fractal analysis of electron-microscope images of pore profiles (Mossotti and Eldeeb, 1992). MORPH-II, an integration of the modified kernel of the program MORPH-I with image calibration and editing facilities, was designed to measure the fractal dimension of the exposed surfaces of stone specimens as imaged in cross section in an electron microscope.

Application of SMP composite in designing a morphing wing

NASA Astrophysics Data System (ADS)

Yu, Kai; Yin, Weilong; Liu, Yanju; Leng, Jinsong

2008-11-01

A new concept of a morphing wing based on shape memory polymer (SMP) and its reinforced composite is proposed in this paper. SMP used in this study is a thermoset styrene-based resin in contrast to normal thermoplastic SMP. In our design, the wing winded on the airframe can be deployed during heating, which provides main lift for a morphing aircraft to realize stable flight. Aerodynamic characteristics of the deployed morphing wing are calculated by using CFD software. The static deformation of the wing under the air loads is also analyzed by using the finite element method. The results show that the used SMP material can provide enough strength and stiffness for the application.

Impact of realistic soil moisture initialization on the representation of extreme events in the western Mediterranean

NASA Astrophysics Data System (ADS)

Helgert, Sebastian; Khodayar, Samiro

2017-04-01

In a warmer Mediterranean climate an increase in the intensity and frequency of extreme events like floods, droughts and extreme heat is expected. The ability to predict such events is still a great challenge and exhibits many uncertainties in the weather forecast and climate predictions. Thereby the missing knowledge about soil moisture-atmosphere interactions and their representation in models is identified as one of the main sources of uncertainty. In this context the soil moisture(SM) plays an important role in the partitioning of sensible and latent heat fluxes on the surface and consequently influences the boundary-layer stability and the precipitation formation. The aim of this research work is to assess the influence of soil moisture-atmosphere interactions on the initiation and development of extreme events in the western Mediterranean (WMED). In this respect the impact of realistic SM initialization on the model representation of extreme events is investigated. High-resolution simulations of different regions in the WMED, including various climate zones from moderate to arid climate, are conducted with the atmospheric COSMO (Consortium for Small-scale Modeling) model in the numerical weather prediction and climate mode. A multiscale temporal and spatial approach is used (days to years, 7km to 2.8km grid spacing). Observational data provided by the framework of the HYdrological cycle in the Mediterranean EXperiment (HyMeX) as well as satellite data such as precipitation from CMORPH (CPC MORPHing technique), evapotranspiration from Land Surface Analysis Satellite Applications Facility (LSA-SAF) and atmospheric moisture from MODIS (Moderate Resolution Imaging Spectroradiometer) are used for process understanding and model validation. To select extreme dry and wet periods the Effective Drought Index (EDI) is calculated. In these periods sensitivity studies of extreme SM initialization scenarios are performed to prove a possible impact of soil moisture on precipitation in the WMED. For the realistic SM initialization different state-of-art high-resolution SM products (25km up to 1km grid spacing) of the Soil Moisture Ocean Salinity mission (SMOS) are examined. A CDF-matching method is applied to reduce the bias between model and SMOS-satellite observation. Moreover, techniques to estimate the initial soil moisture profile from satellite data are tested.

Negative frequency-dependent selection maintains a dramatic flower color polymorphism in the rewardless orchid Dactylorhiza sambucina (L.) Soò

PubMed Central

Gigord, Luc D. B.; Macnair, Mark R.; Smithson, Ann

2001-01-01

The orchid Dactylorhiza sambucina shows a stable and dramatic flower-color polymorphism, with both yellow- and purple-flowered individuals present in natural populations throughout the range of the species in Europe. The evolutionary significance of flower-color polymorphisms found in many rewardless orchid species has been discussed at length, but the mechanisms responsible for their maintenance remain unclear. Laboratory experiments have suggested that behavioral responses by pollinators to lack of reward availability might result in a reproductive advantage for rare-color morphs. Consequently, we performed an experiment varying the relative frequency of the two color morphs of D. sambucina to test whether rare morph advantage acted in the natural habitat of the species. We show here clear evidence from this manipulative experiment that rare-color morphs have reproductive advantage through male and female components. This is the first demonstration, to our knowledge, that negative frequency-dependent selection through pollinator preference for rare morphs can cause the maintenance of a flower-color polymorphism. PMID:11353863

Separation of metadata and pixel data to speed DICOM tag morphing.

PubMed

Ismail, Mahmoud; Philbin, James

2013-01-01

The DICOM information model combines pixel data and metadata in single DICOM object. It is not possible to access the metadata separately from the pixel data. There are use cases where only metadata is accessed. The current DICOM object format increases the running time of those use cases. Tag morphing is one of those use cases. Tag morphing includes deletion, insertion or manipulation of one or more of the metadata attributes. It is typically used for order reconciliation on study acquisition or to localize the issuer of patient ID (IPID) and the patient ID attributes when data from one domain is transferred to a different domain. In this work, we propose using Multi-Series DICOM (MSD) objects, which separate metadata from pixel data and remove duplicate attributes, to reduce the time required for Tag Morphing. The time required to update a set of study attributes in each format is compared. The results show that the MSD format significantly reduces the time required for tag morphing.

Analysis and design of lattice materials for large cord and curvature variations in skin panels of morphing wings

NASA Astrophysics Data System (ADS)

Vigliotti, Andrea; Pasini, Damiano

2015-03-01

In the past few decades, several concepts for morphing wings have been proposed with the aim of improving the structural and aerodynamic performance of conventional aircraft wings. One of the most interesting challenges in the design of a morphing wing is represented by the skin, which needs to meet specific deformation requirements. In particular when morphing involves changes of cord or curvature, the skin is required to undergo large recoverable deformation in the actuation direction, while maintaining the desired shape and strength in the others. One promising material concept that can meet these specifications is represented by lattice materials. This paper examines the use of alternative planar lattices in the embodiment of a skin panel for cord and camber morphing of an aircraft wing. We use a structural homogenization scheme capable of capturing large geometric nonlinearity, to examine the structural performance of lattice skin concepts, as well as to tune their mechanical properties in desired directions.

A zero torsional stiffness twist morphing blade as a wind turbine load alleviation device

NASA Astrophysics Data System (ADS)

Lachenal, X.; Daynes, S.; Weaver, P. M.

2013-06-01

This paper presents the design, analysis and realization of a zero stiffness twist morphing wind turbine blade. The morphing blade is designed to actively twist as a means of alleviating the gust loads which reduce the fatigue life of wind turbine blades. The morphing structure exploits an elastic strain energy balance within the blade to enable large twisting deformations with modest actuation requirements. While twist is introduced using the warping of the blade skin, internal pre-stressed members ensure that a constant strain energy balance is achieved throughout the deformation, resulting in a zero torsional stiffness structure. The torsional stability of the morphing blade is characterized by analysing the elastic strain energy in the device. Analytical models of the skin, the pre-stressed components and the complete blade are compared to their respective finite element models as well as experimental results. The load alleviation potential of the adaptive structure is quantified using a two-dimensional steady flow aerodynamic model which is experimentally validated with wind tunnel measurements.

Colour assortative pairing in a colour polymorphic lizard is independent of population morph diversity

NASA Astrophysics Data System (ADS)

Pérez i de Lanuza, Guillem; Font, Enrique; Carretero, Miguel Ángel

2016-10-01

Previous work with a colour polymorphic population of Podarcis muralis (Lacertidae) revealed that lizards pair by ventral colour, favouring the same colour (i.e. homomorphic) pairs. Such assortative pairing, which probably results in colour assortative mating, can have consequences for the genetic structure of the population and potentially promote speciation. The population previously studied, located in the Pyrenees, encompasses white, yellow and orange animals, as well as intermediate white-orange and yellow-orange morphs. However, other Pyrenean populations of P. muralis have less ventral colour morphs. Our aim in this study is to test the generality of the assortative colour pairing system, extending our previous analyses to populations with different morph compositions and frequencies. The results show that the assortative pattern of pairing is similar in all the populations analysed and, hence, independent of morph composition and not restricted to pentamorphic populations. This suggests that assortative pairing by colour is a general phenomenon for colour polymorphic populations of P. muralis.

The effects of excess calcium on the handling and mechanical properties of hydrothermal derived calcium phosphate bone cement

NASA Astrophysics Data System (ADS)

Razali, N. N.; Sukardi, M. A.; Sopyan, I.; Mel, M.; Salleh, H. M.; Rahman, M. M.

2018-01-01

The objective of this study is to determine the effects of excess calcium on the handling and mechanical properties of hydrothermal derived calcium phosphate cement (CPC) for bone filling applications. Hydroxyapatite powder was synthesized via hydrothermal method using calcium oxide, CaO and ammonium dihydrogen phosphate, NH4H2PO4 as the calcium and phosphorus precursors respectively. The effects of calcium excess were evaluated by varying the CaO content at 0, 5 and 15 mole %. The precursors were then refluxed in distilled water at 90-100°C and dried overnight until the calcium phosphate powder was formed. CPC was then produced by mixing the synthesized powder with distilled water at the powder-to-liquid (P/L) ratio of 1.5. The result from the morphological properties of CPC shows the increase in agglomeration and particles size with 5 mole % of calcium excess but decreased with 15 mole % of calcium excess in CPC. This result was in agreement with the compressive strength result where the CPC increased its strength with 5 mole % of calcium excess but reduced with 15 mole % of calcium excess. The excess in calcium precursor also significantly improved the setting time but reduced the injectability of CPC.

The antifungal properties of chlorhexidine digluconate and cetylpyrinidinium chloride on oral Candida.

PubMed

Fathilah, A R; Himratul-Aznita, W H; Fatheen, A R N; Suriani, K R

2012-07-01

C. tropicalis and C. krusei have emerged as virulent species causing oral infections. Both have developed resistance to commonly prescribed azole antifungal agents. The study aimed to determine the effect of mouth rinses containing chlorhexidine digluconate (CHX), cetylpyridinium chloride (CPC) and their combination (CHX-CPC) on the growth of these strains. The minimal inhibition concentrations (MIC) of the mouth rinses were determined. The growth curves of the strains produced under the mouth rinse-treated and untreated conditions, as well as alterations to the morphology of the growth colonies and cells following the treatments were compared and analysed. The MICs of CPC compared to CHX mouth rinses were found to be lower for both Candida sp. In the mixed formulation, CPC doubled the inhibitory effect of CHX towards both Candida sp., while CHX quadrupled the activity of CPC towards C. tropicalis. The growth colonies also appeared coarse, wrinkled and dried. The profound effects shown may suggest the fungicidal activities of the mouth rinses incorporated with CHX, CPC or their combination on both C. tropicalis and C. krusei. Gargling using mouth rinses with such fungicidal activity would enhance a rapid reduction in the candidal population of patients with fungal infection. Copyright © 2012 Elsevier Ltd. All rights reserved.

Calcium Phosphate Cement with Antimicrobial Properties and Radiopacity as an Endodontic Material

PubMed Central

Shieh, Tzong-Ming; Hsu, Shih-Ming; Chang, Kai-Chi; Lin, Dan-Jae

2017-01-01

Calcium phosphate cements (CPCs) have several advantages for use as endodontic materials, and such advantages include ease of use, biocompatibility, potential hydroxyapatite-forming ability, and bond creation between the dentin and appropriate filling materials. However, unlike tricalcium silicate (CS)-based materials, CPCs do not have antibacterial properties. The present study doped a nonwashable CPC with 0.25–1.0 wt % hinokitiol and added 0, 5, and 10 wt % CS. The CPCs with 0.25–0.5 wt % hinokitiol showed appreciable antimicrobial properties without alterations in their working or setting times, mechanical properties, or cytocompatibility. Addition of CS slightly retarded the apatite formation of CPC and the working and setting time was obviously reduced. Moreover, addition of CS dramatically increased the compressive strength of CPC. Doping CS with 5 wt % ZnO provided additional antibacterial effects to the present CPC system. CS and hinokitiol exerted a synergic antibacterial effect, and the CPC with 0.25 wt % hinokitiol and 10 wt % CS (doped with 5 wt % ZnO) had higher antibacterial properties than that of pure CS. The addition of 10 wt % bismuth subgallate doubled the CPC radiopacity. The results demonstrate that hinokitiol and CS can improve the antibacterial properties of CPCs, and they can thus be considered for endodontic applications. PMID:29088119

The action of chlorphenesin carbamate on the frog spinal cord.

PubMed

Aihara, H; Kurachi, M; Nakane, S; Sasajima, M; Ohzeki, M

1980-02-01

Studies were carried out to elucidate the mechanism of action of chlorphenesin carbamate (CPC) and to compare the effect of the drug with that of mephenesin on the isolated bullfrog spinal cord. Ventral and dorsal root potentials were recorded by means of the sucrose-gap method. CPC caused marked hyperpolarizations and depressed spontaneous activities in both of the primary afferent terminals (PAT) and motoneurons (MN). These hyperpolarizations were observed even in high-Mg2+ and Ca2+-free Ringer's solution, suggesting that CPC has direct actions on PAT and MN. Various reflex potentials (dorsal and ventral root potentials elicited by stimulating dorsal and ventral root, respectively) tended to be depressed by CPC as well as by mephenesin. Excitatory amino acids (L-aspartic acid and L-glutamic acid) caused marked depolarizations in PAT and MN, and increased the firing rate in MN. CPC did not modify the depolarization but abolished the motoneuron firing induced by these amino acids. However, mephenesin reduced both the depolarization and the motoneuron firing. The dorsal and ventral root potentials evoked by tetanic stimulation (40 Hz) of the dorsal root were depressed by the drugs. These results indicate that CPC has an apparent depressing action on the spinal neuron, and this action may be ascribed to the slight hyperpolarization and/or the prolongation of refractory period.

Blooming Knit Flowers: Loop-Linked Soft Morphing Structures for Soft Robotics.

PubMed

Han, Min-Woo; Ahn, Sung-Hoon

2017-04-01

A loop-linked structure, which is capable of morphing in various modes, including volumetric transformation, is developed based on knitting methods. Morphing flowers (a lily-like, a daffodil-like, gamopetalous, and a calla-like flower) are fabricated using loop patterning, and their blooming motion is demonstrated by controlling a current that selectively actuates the flowers petals. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Altay falcon: Origin, morphology and distribution

USGS Publications Warehouse

Ellis, D.H.

1995-01-01

The systematic position of the Altay falcon (Falco altaicus lorenzi) is perhaps the most enigmatic question lingering in falcon taxonomy. First reported to science in 1811, it has been treated as a race of the gyrfalcon (F. rusticolus), as a race of the saker (F. cherrug), as two separate species (F. lorenzi and F. altaicus), and as one to three color morphs of either the saker or the gyrfalcon. Ironically, two or even more of these explanations may be correct. Of 53 specimens examined, at least two are misidentified gyrfalcons, a score I dismiss as typical sakers, but a sizeable group (N = 34) is retained as representing what I consider to be the true Altay falcon type. Three adult color morphs exist: red, brown and grey. The red-backed morph closely resembles some eastern sakers. The chocolate morph resembles the black gyrfalcon from Labrador. The grey morph resembles the grey morph of the gyrfalcon. Ecological, geographical and morphological information contribute to the conclusion that this core group represents a gyrfalcon-saker hybrid that is very likely being swamped into obscurity through back crosses with the saker. The breeding range reported herein (Altay-Sayan Mountains) is greatly contracted from that previously reported. The true identify of the Altay falcon will be resolved by molecular genetics.

Composite corrugated structures for morphing wing skin applications

NASA Astrophysics Data System (ADS)

Thill, C.; Etches, J. A.; Bond, I. P.; Potter, K. D.; Weaver, P. M.

2010-12-01

Composite corrugated structures are known for their anisotropic properties. They exhibit relatively high stiffness parallel (longitudinal) to the corrugation direction and are relatively compliant in the direction perpendicular (transverse) to the corrugation. Thus, they offer a potential solution for morphing skin panels (MSPs) in the trailing edge region of a wing as a morphing control surface. In this paper, an overview of the work carried out by the present authors over the last few years on corrugated structures for morphing skin applications is first given. The second part of the paper presents recent work on the application of corrugated sandwich structures. Panels made from multiple unit cells of corrugated sandwich structures are used as MSPs in the trailing edge region of a scaled morphing aerofoil section. The aerofoil section features an internal actuation mechanism that allows chordwise length and camber change of the trailing edge region (aft 35% chord). Wind tunnel testing was carried out to demonstrate the MSP concept but also to explore its limitations. Suggestions for improvements arising from this study were deduced, one of which includes an investigation of a segmented skin. The overall results of this study show that the MSP concept exploiting corrugated sandwich structures offers a potential solution for local morphing wing skins for low speed and small air vehicles.

Approaching morphing wing concepts on the basis of micro aerial vehicles

NASA Astrophysics Data System (ADS)

Boller, C.; Kuo, C.-M.; Qin, N.

2007-04-01

Morphing wings have been discussed since the early days of smart structures. Concepts and demonstrations started mainly in the context of real existing fixed wing aircraft. The complexity of existing aircraft and the limitations in terms of energy required and thus resulting cost made morphing wings mainly impossible to be successfully integrated into existing aircraft designs. Going however to smaller scaled aircraft where designs are less or possibly even not defined at all makes demonstration of morphing wings much more feasible. This paper will therefore discuss some morphing wing issues for micro aerial vehicle (MAV) designs where an MAV is considered to be an air vehicle of around 30 to 50 cm in span and a weight of less than 250 grams. At first the aerodynamics in terms of different wing shapes for such a small type of aircraft will be discussed followed by a design procedure on how to successfully design and analyse a morphing wing MAV. A more detailed description will then be given with regard to adaptively changing a wing's thickness where the actuation principles applied will be outlined in terms of conventional mechanical as well as smart structural solutions. Experimental results achieved in real flight tests will be described and discussed.

Antimicrobial efficacy of 0·05% cetylpyridinium chloride mouthrinses.

PubMed

Sreenivasan, P K; Haraszthy, V I; Zambon, J J

2013-01-01

This study evaluated the antimicrobial activity of two commercially available 0·05% cetylpyridinium chloride (CPC) mouthrinses with or without alcohol and examined its antimicrobial activity on oral bacterial species including fresh clinical isolates compared to a chlorhexidine mouthrinse and a control fluoride mouthrinse without CPC. Two different approaches were used to evaluate antimicrobial activity. First, the minimum inhibitory concentration (MIC) was determined for each mouthrinse against a panel of 25 micro-organisms including species associated with dental caries, gingivitis and periodontitis. Second, supragingival dental plaque obtained from 15 adults was incubated with the four mouthrinses to evaluate antimicrobial activity on micro-organisms in oral biofilms. Both CPC mouthrinses exhibited lower MIC's, that is, greater antimicrobial activity, against oral Gram-negative bacteria especially periodontal pathogens and species implicated in halitosis such as Aggregatibacter actinomycemcomitans, Campylobacter rectus, Eikenella corrodens, Porphyromonas gingivalis, Prevotella intermedia and Solobacterium moorei than the control mouthrinse. Ex-vivo tests on supragingival plaque micro-organisms demonstrated significantly greater antimicrobial activity by the CPC mouthrinses (>90% killing, P < 0·001) and the chlorhexidine rinse (>98% killing, P < 0·05) compared to the control fluoride mouthrinse. Whilst the chlorhexidine mouthrinse was most effective, mouthrinses containing 0·05% CPC formulated with or without alcohol demonstrated broad-spectrum antimicrobial activity against both laboratory strains and supragingival plaque bacteria compared to a control mouthrinse without CPC. These in vitro and ex-vivo studies provide a biological rationale for previous clinical studies demonstrating the efficacy of CPC mouthrinses in reducing supragingival plaque and plaque-associated gingivitis. © 2012 The Society for Applied Microbiology.

Shell colour, temperature, (micro)habitat structure and predator pressure affect the behaviour of Cepaea nemoralis

NASA Astrophysics Data System (ADS)

Rosin, Zuzanna M.; Kwieciński, Zbigniew; Lesicki, Andrzej; Skórka, Piotr; Kobak, Jarosław; Szymańska, Anna; Osiejuk, Tomasz S.; Kałuski, Tomasz; Jaskulska, Monika; Tryjanowski, Piotr

2018-06-01

Although shell colour polymorphism of the land snail Cepaea nemoralis is a well-known phenomenon, proximate and ultimate factors driving its evolution remain uncertain. Polymorphic species show variation in behavioural responses to selective forces. Therefore, we estimated effects of various environmental factors (temperature, humidity, food availability, (micro)habitat structure and predatory pressure) on behavioural response (frequency of locomotion, climbing and hiding) of C. nemoralis morphs, in experimental and natural conditions. In the experimental part of study, the frequency of locomotion was negatively affected by temperature and the presence of food and positively influenced by the presence of light. Morphs significantly differed in behavioural responses to environmental variability. Pink mid-banded and yellow five-banded morphs climbed less often and hide in shelter more often than yellow and pink unbanded individuals when temperature was low and food was absent. Snails fed most often at moderate temperature compared to low and high temperatures. Field investigations partially confirmed differences among morphs in frequency of climbing, but not in terms of probability of hiding in sheltered sites. In natural colonies, temperature and (micro)habitat structure significantly affected frequency of climbing as well as hiding in shelter. Snails more often hid in sheltered sites where thrushes preyed on Cepaea. Tendency of unbanded morphs to climb trees may have evolved under avian predatory pressure as thrushes forage on a ground. Tendency of banded morphs to hide in sheltered sites may reflect prey preferences for cryptic background. The results implicate that differential behaviour of C. nemoralis morphs compensate for their morphological and physiological limitations of adaptation to habitat.

Is Beauty in the Face of the Beholder?

PubMed Central

Laeng, Bruno; Vermeer, Oddrun; Sulutvedt, Unni

2013-01-01

Opposing forces influence assortative mating so that one seeks a similar mate while at the same time avoiding inbreeding with close relatives. Thus, mate choice may be a balancing of phenotypic similarity and dissimilarity between partners. In the present study, we assessed the role of resemblance to Self’s facial traits in judgments of physical attractiveness. Participants chose the most attractive face image of their romantic partner among several variants, where the faces were morphed so as to include only 22% of another face. Participants distinctly preferred a “Self-based morph” (i.e., their partner’s face with a small amount of Self’s face blended into it) to other morphed images. The Self-based morph was also preferred to the morph of their partner’s face blended with the partner’s same-sex “prototype”, although the latter face was (“objectively”) judged more attractive by other individuals. When ranking morphs differing in level of amalgamation (i.e., 11% vs. 22% vs. 33%) of another face, the 22% was chosen consistently as the preferred morph and, in particular, when Self was blended in the partner’s face. A forced-choice signal-detection paradigm showed that the effect of self-resemblance operated at an unconscious level, since the same participants were unable to detect the presence of their own faces in the above morphs. We concluded that individuals, if given the opportunity, seek to promote “positive assortment” for Self’s phenotype, especially when the level of similarity approaches an optimal point that is similar to Self without causing a conscious acknowledgment of the similarity. PMID:23874608

Shell colour, temperature, (micro)habitat structure and predator pressure affect the behaviour of Cepaea nemoralis.

PubMed

Rosin, Zuzanna M; Kwieciński, Zbigniew; Lesicki, Andrzej; Skórka, Piotr; Kobak, Jarosław; Szymańska, Anna; Osiejuk, Tomasz S; Kałuski, Tomasz; Jaskulska, Monika; Tryjanowski, Piotr

2018-05-09

Although shell colour polymorphism of the land snail Cepaea nemoralis is a well-known phenomenon, proximate and ultimate factors driving its evolution remain uncertain. Polymorphic species show variation in behavioural responses to selective forces. Therefore, we estimated effects of various environmental factors (temperature, humidity, food availability, (micro)habitat structure and predatory pressure) on behavioural response (frequency of locomotion, climbing and hiding) of C. nemoralis morphs, in experimental and natural conditions. In the experimental part of study, the frequency of locomotion was negatively affected by temperature and the presence of food and positively influenced by the presence of light. Morphs significantly differed in behavioural responses to environmental variability. Pink mid-banded and yellow five-banded morphs climbed less often and hide in shelter more often than yellow and pink unbanded individuals when temperature was low and food was absent. Snails fed most often at moderate temperature compared to low and high temperatures. Field investigations partially confirmed differences among morphs in frequency of climbing, but not in terms of probability of hiding in sheltered sites. In natural colonies, temperature and (micro)habitat structure significantly affected frequency of climbing as well as hiding in shelter. Snails more often hid in sheltered sites where thrushes preyed on Cepaea. Tendency of unbanded morphs to climb trees may have evolved under avian predatory pressure as thrushes forage on a ground. Tendency of banded morphs to hide in sheltered sites may reflect prey preferences for cryptic background. The results implicate that differential behaviour of C. nemoralis morphs compensate for their morphological and physiological limitations of adaptation to habitat.

Continuous professional competence (CPC) for emergency medical technicians in Ireland: educational needs assessment

PubMed Central

2013-01-01

Background As in other countries, the Irish Regulator for Pre-Hospital practitioners, the Pre-Hospital Emergency Care Council (PHECC), will introduce a Continuous Professional Competence (CPC) framework for all Emergency Medical Technicians (EMTs), Paramedics and Advanced Paramedics (APs). This framework involves EMTs participating in regular and structured training to maintain professional competence and enable continuous professional developments. To inform the development of this framework, this study aimed to identify what EMTs consider the optimum educational outcomes and activity and their attitude towards CPC. Methods All EMTs registered in Ireland (n = 925) were invited via email to complete an anonymous online survey. Survey questions were designed based on Continuous Professional Development (CPD) questionnaires used by other healthcare professions. Quantitative and qualitative analyses were performed. Results Response rate was 43% (n = 399). 84% of participants had been registered in Ireland for less than 24 months, while 59% had been registered EMTs for more than one year. Outcomes were: evidence of CPC should be a condition for EMT registration in Ireland (95%), 78% believed that EMTs who do not maintain CPC should be denied the option to re-register. Although not required to do so at the time of survey, 69% maintained a professional portfolio and 24% had completed up to 20 hours of CPC activities in the prior 12 months. From a list of 22 proposed CPC activities, 97% stated that practical scenario-based exercises were most relevant to their role. E-learning curricula without practical components were considered irrelevant (32%), but the majority of participants (91%) welcomed access to e-learning when supplemented by related practical modules. Conclusion EMTs are supportive of CPC as a key part of their professional development and registration. Blended learning, which involves clinical and practical skills and e-learning, is the optimum approach. PMID:24345064

Floral polymorphism and the fitness implications of attracting pollinating and florivorous insects.

PubMed

de Jager, Marinus L; Ellis, Allan G

2014-01-01

Floral polymorphism is frequently attributed to pollinator-mediated selection. Multiple studies, however, have revealed the importance of non-pollinating visitors in floral evolution. Using the polymorphic annual daisy Ursinia calenduliflora, this study investigated the importance of different insect visitors, and their effects on fitness, in the maintenance of floral polymorphism. The spatial structure of a discrete floral polymorphism was characterized based on the presence/absence of anthocyanin floret spots in U. calenduliflora. A 3-year observational study was then conducted in polymorphic populations to investigate differences in visitation rates of dominant visitors to floral morphs. Experiments were performed to explore the floral preference of male and female Megapalpus capensis (the dominant insect visitor) and their effectiveness as pollinators. Next, floral damage by antagonistic florivores and the reproductive success of the two floral morphs were surveyed in multiple populations and years. Floral polymorphism in U. calenduliflora was structured spatially, as were insect visitation patterns. Megapalpus capensis males were the dominant visitors and exhibited strong preference for the spotted morph in natural and experimental observations. While this may indicate potential fitness benefits for the spotted morph, female fitness did not differ between floral morphs. However, as M. capensis males are very efficient at exporting U. calenduliflora pollen, their preference may likely increase the reproductive fitness of the spotted morph through male fitness components. The spotted morph, however, also suffered significantly greater costs due to ovule predation by florivores than the spotless morph. The results suggest that pollinators and florivores may potentially exert antagonistic selection that could contribute to the maintenance of floral polymorphism across the range of U. calenduliflora. The relative strength of selection imposed by each agent is potentially determined by insect community composition and abundance at each site, highlighting the importance of community context in the evolution of floral phenotypes.

Evidence for Sexual Dimorphism in the Plated Dinosaur Stegosaurus mjosi (Ornithischia, Stegosauria) from the Morrison Formation (Upper Jurassic) of Western USA.

PubMed

Saitta, Evan Thomas

2015-01-01

Conclusive evidence for sexual dimorphism in non-avian dinosaurs has been elusive. Here it is shown that dimorphism in the shape of the dermal plates of Stegosaurus mjosi (Upper Jurassic, western USA) does not result from non-sex-related individual, interspecific, or ontogenetic variation and is most likely a sexually dimorphic feature. One morph possessed wide, oval plates 45% larger in surface area than the tall, narrow plates of the other morph. Intermediate morphologies are lacking as principal component analysis supports marked size- and shape-based dimorphism. In contrast, many non-sex-related individual variations are expected to show intermediate morphologies. Taphonomy of a new quarry in Montana (JRDI 5ES Quarry) shows that at least five individuals were buried in a single horizon and were not brought together by water or scavenger transportation. This new site demonstrates co-existence, and possibly suggests sociality, between two morphs that only show dimorphism in their plates. Without evidence for niche partitioning, it is unlikely that the two morphs represent different species. Histology of the new specimens in combination with studies on previous specimens indicates that both morphs occur in fully-grown individuals. Therefore, the dimorphism is not a result of ontogenetic change. Furthermore, the two morphs of plates do not simply come from different positions on the back of a single individual. Plates from all positions on the body can be classified as one of the two morphs, and previously discovered, isolated specimens possess only one morph of plates. Based on the seemingly display-oriented morphology of plates, female mate choice was likely the driving evolutionary mechanism rather than male-male competition. Dinosaur ornamentation possibly served similar functions to the ornamentation of modern species. Comparisons to ornamentation involved in sexual selection of extant species, such as the horns of bovids, may be appropriate in predicting the function of some dinosaur ornamentation.

A clinical study to assess the 12-hour antimicrobial effects of cetylpyridinium chloride mouthwashes on supragingival plaque bacteria.

PubMed

He, Songlin; Wei, Yin; Fan, Xu; Hu, Deyu; Sreenivasan, P K

2011-01-01

This randomized double-blind clinical study evaluated the antimicrobial efficacy of two mouthwashes containing (1) 0.075% cetylpyridinium chloride (CPC) + 0.05% sodium fluoride (NaF) in an alcohol-free base and (2) 0.075% CPC + 0.05% NaF in a 6% alcohol base, versus a negative control mouthwash containing 0.05% NaF in an alcohol-free base on numbers of bacteria in supragingival plaque 12 hours after a single use and 12 hours after 14 days' use. Enrolled subjects completed a one-week washout phase prior to providing baseline samples of supragingival plaque that were analyzed for numbers of anaerobic microorganisms. Subjects were randomized to a treatment group and instructed to rinse with 20 mL of the assigned mouthwash for 30 seconds. Post-treatment microbiological analyses were conducted on plaque samples collected 12 hours after the first use of each assigned mouthwash and after completing 14 days of twice-daily use of each assigned mouthwash. Oral examinations were completed by a dentist at each sample collection to assess soft and hard tissue oral health over the course of the study. The study enrolled 188 adults (mean age 45.78 years; age range 23-69). Subjects rinsing with the CPC-containing mouthwash realized a statistically significant (p < 0.05) reduction in numbers of supragingival anaerobic bacteria at the 12-hour evaluation after a single use. In comparison to the control mouthwash, use of the CPC mouthwash in an alcohol base resulted in a 35.3% reduction in numbers of anaerobic plaque bacteria, while the CPC mouthwash in an alcohol-free base demonstrated a 34.5% reduction. Further, the analysis after twice-daily use for 14 days indicated that the CPC mouthwash in an alcohol base demonstrated a 73.8% reduction in anaerobic plaque bacteria, while the CPC mouthwash in an alcohol-free base demonstrated a 70.9% reduction in anaerobic plaque bacteria versus the control mouthwash. The CPC mouthwash in an alcohol-free base reduced supragingival plaque bacteria by 34.5% and 70.9% compared to the control mouthwash 12 hours after a single use and after 14 days of use, respectively. In addition, the CPC mouthwash in an alcohol base reduced supragingival bacteria by 35.3% and 73.8% compared to the control mouthwash 12 hours after a single use and after 14 days of use, respectively. There were no statistically significant differences between the CPC-containing mouthwashes at either of the post-treatment time points.

Mechanisms and actuators for rotorcraft blade morphing

NASA Astrophysics Data System (ADS)

Vocke, Robert D., III

The idea of improved fight performance through changes in the control surfaces dates back to the advent of aviation with the Wright brothers' pioneering work on "wing warping," but it was not until the recent progress in material and actuator development that such control surfaces seemed practical for modern aircraft. This has opened the door to a new class of aircraft that have the ability to change shape or morph, which are being investigated due to the potential to have a single platform serve multiple mission objectives, as well as improve performance characteristics. While the majority of existing research for morphing aircraft has focused on fixedwing aircraft, rotary-wing aircraft have begun to receive more attention. The purpose of this body of work is to investigate the current state of morphing actuation technology for rotorcraft and improve upon it. Specifically, this work looks at two types of morphing: Pneumatic Artificial Muscle (PAM) actuated trailing edge flaps and conformal variable diameter morphing. First, active camber changes through the use of PAM powered trailing edge flaps were investigated due to the potential for reductions in power requirements and vibration/noise levels. A PAM based antagonistic actuation system was developed utilizing a novel combination of mechanism geometry and PAM bias contraction optimization to overcome the natural extension stiffening characteristics of PAMs. In open-loop bench-top testing against a "worst-case" constant torsional loading, the system demonstrated actuation authority suitable for both primary control and vibration/noise reduction. Additionally, closed-loop test data indicated that the system was capable of tracking complex waveforms consistent with those needed for rotorcraft control. This system demonstrated performance on-par with the state of the art pneumatic trailing edge flap actuators, yet with a much smaller footprint and impact on the rotor-blade. The second morphing system developed in this work is a conformal variable diameter rotor system suitable for implementation on a modern tilt-rotor aircraft, which can reduce power requirements in both cruise and hover configurations. An initial prototype variable span airfoil was constructed using a silicone elastomer matrix composite skin and a plastic rapid prototyped morphing substructure. Benchtop and wind tunnel tests verified the ability of this system to increase active wing area by 100%. The prototype technology was then matured for use in the harsh rotor blade environment, with a much stiffer polyurethane skin and a titanium substructure. Coupon testing verified the efficacy of this approach, and a final conceptual design was completed using the stiffness-tuning characteristics of the morphing substructure to create a self-actuating morphing blade tip.

Distribution of Flower Morphs, Ploidy Level and Sexual Reproduction of the Invasive Weed Oxalis pes-caprae in the Western Area of the Mediterranean Region

PubMed Central

Castro, Sílvia; Loureiro, João; Santos, Conceição; Ater, Mohammed; Ayensa, Garbiñe; Navarro, Luis

2007-01-01

Background and Aims Oxalis pes-caprae is a widespread invasive weed in regions with a Mediterranean climate. In its native habitat (southern Africa) this species has been reported as heterostylous with trimorphic flowers and a self- and morph-incompatible reproductive system. In most of the areas invaded, only a pentaploid short-styled morphotype that reproduces mainly asexually by bulbils is reported, but this has only been confirmed empirically. This study aims to analyse the floral morph proportions in a wide distribution area, test the sexual female success, and explain the causes of low sexual reproduction of this species in the western area of the Mediterranean Basin. Methods Fifty-five populations of O. pes-caprae were sampled in the Iberian Peninsula and Morocco to evaluate the floral morph ratio and individual fruit set. In plants from a dimorphic population, hand-pollination experiments were performed to evaluate the effect of the pollen source on pollen tube growth through the style. The ploidy level and genome size of individuals of each floral morph were analysed using flow cytometry. Key Results From the populations studied 89·1 % were monomorphic, with most of them containing the short-styled (SS) floral morph, and 10·9 % were dimorphic containing long-styled (LS) and SS morphs. In some of these, isoplethy was verified but no fruit production was observed in any population. A sterile form was also recorded in several populations. Hand-pollination experiments revealed that pollen grains germinated over recipient stigmas. In intermorph crossings, pollen tubes were able to develop and fruit initiation was observed in some cases, while in intramorph pollinations, pollen tube development was sporadic and no fruit initiation was observed. All individuals within each floral form presented the same DNA ploidy level: SS plants were pentaploid and LS and the sterile form were tetraploid. Conclusions The low or null sexual reproduction success of this species in the area of invasion studied seems related with the high frequency of monomorphic populations, the unequal proportion of floral morphs in dimorphic populations and the presence of different ploidy levels between SS and LS morphs. The discovery of the occurrence of an LS floral morph and a sterile form, whose invading capacity in these areas is as yet unknown, will be valuable information for management programmes. PMID:17218342

Relationship between delta power and the electrocardiogram-derived cardiopulmonary spectrogram: possible implications for assessing the effectiveness of sleep.

PubMed

Thomas, Robert Joseph; Mietus, Joseph E; Peng, Chung-Kang; Guo, Dan; Gozal, David; Montgomery-Downs, Hawley; Gottlieb, Daniel J; Wang, Cheng-Yen; Goldberger, Ary L

2014-01-01

The physiologic relationship between slow-wave activity (SWA) (0-4 Hz) on the electroencephalogram (EEG) and high-frequency (0.1-0.4 Hz) cardiopulmonary coupling (CPC) derived from electrocardiogram (ECG) sleep spectrograms is not known. Because high-frequency CPC appears to be a biomarker of stable sleep, we tested the hypothesis that that slow-wave EEG power would show a relatively fixed-time relationship to periods of high-frequency CPC. Furthermore, we speculated that this correlation would be independent of conventional nonrapid eye movement (NREM) sleep stages. We analyzed selected datasets from an archived polysomnography (PSG) database, the Sleep Heart Health Study I (SHHS-I). We employed the cross-correlation technique to measure the degree of which 2 signals are correlated as a function of a time lag between them. Correlation analyses between high-frequency CPC and delta power (computed both as absolute and normalized values) from 3150 subjects with an apnea-hypopnea index (AHI) of ≤5 events per hour of sleep were performed. The overall correlation (r) between delta power and high-frequency coupling (HFC) power was 0.40±0.18 (P=.001). Normalized delta power provided improved correlation relative to absolute delta power. Correlations were somewhat reduced in the second half relative to the first half of the night (r=0.45±0.20 vs r=0.34±0.23). Correlations were only affected by age in the eighth decade. There were no sex differences and only small racial or ethnic differences were noted. These results support a tight temporal relationship between slow wave power, both within and outside conventional slow wave sleep periods, and high frequency cardiopulmonary coupling, an ECG-derived biomarker of "stable" sleep. These findings raise mechanistic questions regarding the cross-system integration of neural and cardiopulmonary control during sleep. Copyright © 2013 Elsevier B.V. All rights reserved.

Effect of Poly(Vinyl Alcohol) Addition on the Properties of Hydrothermal Derived Calcium Phosphate Cement for Bone Filling Materials

NASA Astrophysics Data System (ADS)

Razali, N. N.; Sopyan, I.; Mel, M.; Salleh, H. M.; Rahman, M. M.; Singh, R.

2017-06-01

The effect of addition of poly(vinyl alcohol) on hydrothermal derived calcium phosphate cement has been studied. The precursors used to prepare the cement were calcium oxide (CaO) and ammonium dihydrogen phosphate (NH4H2PO4); the reaction was conducted in water at 80-100°C. To improve properties of CPC, poly(vinyl alcohol) (PVA) of 1wt% and 2wt% was added to the liquid phase of CPC and the results were compared to CPC without PVA addition. The addition of PVA was proved to bring remarkable effects on cohesion, setting time and mechanical strength of CPC which make it suitable physically for injectable bone filler applications.

Efficacy of cetylpyridinium chloride against Listeria monocytogenes and its influence on color and texture of cooked roast beef.

PubMed

Singh, M; Thippareddi, H; Phebus, R K; Marsden, J L; Herald, T J; Nutsch, A L

2005-11-01

Sliced (cut) and exterior (intact) surfaces of restructured cooked roast beef were inoculated with Listeria monocytogenes, treated with cetylpyridinium chloride (CPC; immersion in 500 ml of 1% solution for 1 min), individually vacuum packaged, and stored for 42 days at 0 or 4 degrees C. Noninoculated samples were similarly treated, packaged, and stored to determine effects on quality (color and firmness) and on naturally occurring bacterial populations, including aerobic plate counts and lactic acid bacteria. Immediately after CPC treatment, regardless of inoculation level, L. monocytogenes populations were reduced (P = 0.05) by about 2 log CFU/cm2 on sliced surfaces and by about 4 log CFU/cm2 on exterior surfaces. Throughout 42 days of refrigerated storage (at both 0 and 4 degrees C), L. monocytogenes populations on CPC-treated samples remained lower (P = 0.05) than those of nontreated samples for both surface types. After 42 days of storage at both 0 and 4 degrees C, aerobic plate count and lactic acid bacteria populations of treated samples were 1 to 1.5 log CFU/cm2 lower (P = 0.05) than those of nontreated samples for both surface types. CPC treatment resulted in negligible effects (P > 0.05) on the color (L*, a*, and b* values) of exterior and sliced roast beef surfaces during storage. For both sliced and exterior surfaces, CPC-treated samples were generally less firm than nontreated samples. CPC treatment effectively reduced L. monocytogenes populations on roast beef surfaces and resulted in relatively minor impacts on color and texture attributes. CPC treatment, especially when applied to products prior to slicing, may serve as an effective antimicrobial intervention for ready-to-eat meat products.

Cloud cover detection combining high dynamic range sky images and ceilometer measurements

NASA Astrophysics Data System (ADS)

Román, R.; Cazorla, A.; Toledano, C.; Olmo, F. J.; Cachorro, V. E.; de Frutos, A.; Alados-Arboledas, L.

2017-11-01

This paper presents a new algorithm for cloud detection based on high dynamic range images from a sky camera and ceilometer measurements. The algorithm is also able to detect the obstruction of the sun. This algorithm, called CPC (Camera Plus Ceilometer), is based on the assumption that under cloud-free conditions the sky field must show symmetry. The symmetry criteria are applied depending on ceilometer measurements of the cloud base height. CPC algorithm is applied in two Spanish locations (Granada and Valladolid). The performance of CPC retrieving the sun conditions (obstructed or unobstructed) is analyzed in detail using as reference pyranometer measurements at Granada. CPC retrievals are in agreement with those derived from the reference pyranometer in 85% of the cases (it seems that this agreement does not depend on aerosol size or optical depth). The agreement percentage goes down to only 48% when another algorithm, based on Red-Blue Ratio (RBR), is applied to the sky camera images. The retrieved cloud cover at Granada and Valladolid is compared with that registered by trained meteorological observers. CPC cloud cover is in agreement with the reference showing a slight overestimation and a mean absolute error around 1 okta. A major advantage of the CPC algorithm with respect to the RBR method is that the determined cloud cover is independent of aerosol properties. The RBR algorithm overestimates cloud cover for coarse aerosols and high loads. Cloud cover obtained only from ceilometer shows similar results than CPC algorithm; but the horizontal distribution cannot be obtained. In addition, it has been observed that under quick and strong changes on cloud cover ceilometers retrieve a cloud cover fitting worse with the real cloud cover.

Pulmonary hypertension and ventilation during exercise: Role of the pre-capillary component.

PubMed

Caravita, Sergio; Faini, Andrea; Deboeck, Gael; Bondue, Antoine; Naeije, Robert; Parati, Gianfranco; Vachiéry, Jean-Luc

2017-07-01

Excessive exercise-induced hyperventilation and high prevalence of exercise oscillatory breathing (EOB) are present in patients with post-capillary pulmonary hypertension (PH) complicating left heart disease (LHD). Patients with pre-capillary PH have even higher hyperventilation but no EOB. We sought to determine the impact of a pre-capillary component of PH on ventilatory response to exercise in patients with PH and left heart disease. We retrospectively compared patients with idiopathic or heritable pulmonary arterial hypertension (PAH, n = 29), isolated post-capillary PH (IpcPH, n = 29), and combined post- and pre-capillary PH (CpcPH, n = 12). Diastolic pressure gradient (DPG = diastolic pulmonary artery pressure - pulmonary wedge pressure) was used to distinguish IpcPH (DPG <7 mm Hg) from CpcPH (DPG ≥7 mm Hg). Pulmonary vascular resistance (PVR) was higher in PAH, intermediate in CpcPH, and low in IpcPH. All patients with CpcPH but 1 had PVR >3 Wood unit. Exercise-induced hyperventilation (high minute ventilation over carbon dioxide production, low end-tidal carbon dioxide) was marked in PAH, intermediate in CpcPH, and low in IpcPH (p < 0.001) and correlated with DPG and PVR. Prevalence of EOB decreased from IpcPH to CpcPH to PAH (p < 0.001). Patients with CpcPH may have worse hemodynamics than patients with IpcPH and distinct alterations of ventilatory control, consistent with more exercise-induced hyperventilation and less EOB. This might be explained at least in part by the presence and extent of pulmonary vascular disease. Copyright © 2017 International Society for Heart and Lung Transplantation. Published by Elsevier Inc. All rights reserved.

Injectable calcium phosphate with hydrogel fibers encapsulating induced pluripotent, dental pulp and bone marrow stem cells for bone repair

PubMed Central

Wang, Lin; Zhang, Chi; Li, Chunyan; Weir, Michael D.; Wang, Ping; Reynolds, Mark A.; Zhao, Liang; Xu, Hockin H.K.

2017-01-01

Human induced pluripotent stem cell-derived mesenchymal stem cells (hiPSC-MSCs), dental pulp stem cells (hDPSCs) and bone marrow MSCs (hBMSCs) are exciting cell sources in regenerative medicine. However, there has been no report comparing hDPSCs, hBMSCs and hiPSC-MSCs for bone engineering in an injectable calcium phosphate cement (CPC) scaffold. The objectives of this study were to: (1) develop a novel injectable CPC containing hydrogel fibers encapsulating stem cells for bone engineering, and (2) compare cell viability, proliferation and osteogenic differentiation of hDPSCs, hiPSC-MSCs from bone marrow (BM-hiPSC-MSCs) and from foreskin (FS-hiPSC-MSCs), and hBMSCs in CPC for the first time. The results showed that the injection did not harm cell viability. The porosity of injectable CPC was 62%. All four types of cells proliferated and differentiated down the osteogenic lineage inside hydrogel fibers in CPC. hDPSCs, BM-hiPSC-MSCs, and hBMSCs exhibited high alkaline phosphatase, runt-related transcription factor, collagen I, and osteocalcin gene expressions. Cell-synthesized minerals increased with time (p < 0.05), with no significant difference among hDPSCs, BM-hiPSC-MSCs and hBMSCs (p > 0.1). Mineralization by hDPSCs, BM-hiPSC-MSCs, and hBMSCs inside CPC at 14 d was 14-fold that at 1 d. FS-hiPSC-MSCs were inferior in osteogenic differentiation compared to the other cells. In conclusion, hDPSCs, BM-hiPSC-MSCs and hBMSCs are similarly and highly promising for bone tissue engineering; however, FS-hiPSC-MSCs were relatively inferior in osteogenesis. The novel injectable CPC with cell-encapsulating hydrogel fibers may enhance bone regeneration in dental, craniofacial and orthopedic applications. PMID:27612810

Testosterone-Induced Expression of Male Colour Morphs in Females of the Polymorphic Tawny Dragon Lizard, Ctenophorus decresii.

PubMed

Rankin, Katrina; Stuart-Fox, Devi

2015-01-01

Many colour polymorphisms are present only in one sex, usually males, but proximate mechanisms controlling the expression of sex-limited colour polymorphisms have received little attention. Here, we test the hypothesis that artificial elevation of testosterone in females of the colour polymorphic tawny dragon lizard, Ctenophorus decresii, can induce them to express the same colour morphs, in similar frequencies, to those found in males. Male C. decresii, express four discrete throat colour morphs (orange, yellow, grey and an orange central patch surrounded by yellow). We used silastic implants to experimentally elevate testosterone levels in mature females to induce colour expression. Testosterone elevation resulted in a substantial increase in the proportion and intensity of orange but not yellow colouration, which was present in a subset of females prior to treatment. Consequently, females exhibited the same set of colour morphs as males, and we confirmed that these morphs are objectively classifiable, by using digital image analyses and spectral reflectance measurements, and occur in similar frequencies as in males. These results indicate that the influence of testosterone differs for different colours, suggesting that their expression may be governed by different proximate hormonal mechanisms. Thus, caution must be exercised when using artificial testosterone manipulation to induce female expression of sex-limited colour polymorphisms. Nevertheless, the ability to express sex-limited colours (in this case orange) to reveal the same, objectively classifiable morphs in similar frequencies to males suggests autosomal rather than sex-linked inheritance, and can facilitate further research on the genetic basis of colour polymorphism, including estimating heritability and selection on colour morphs from pedigree data.

Testosterone-Induced Expression of Male Colour Morphs in Females of the Polymorphic Tawny Dragon Lizard, Ctenophorus decresii

PubMed Central

Rankin, Katrina; Stuart-Fox, Devi

2015-01-01

Many colour polymorphisms are present only in one sex, usually males, but proximate mechanisms controlling the expression of sex-limited colour polymorphisms have received little attention. Here, we test the hypothesis that artificial elevation of testosterone in females of the colour polymorphic tawny dragon lizard, Ctenophorus decresii, can induce them to express the same colour morphs, in similar frequencies, to those found in males. Male C. decresii, express four discrete throat colour morphs (orange, yellow, grey and an orange central patch surrounded by yellow). We used silastic implants to experimentally elevate testosterone levels in mature females to induce colour expression. Testosterone elevation resulted in a substantial increase in the proportion and intensity of orange but not yellow colouration, which was present in a subset of females prior to treatment. Consequently, females exhibited the same set of colour morphs as males, and we confirmed that these morphs are objectively classifiable, by using digital image analyses and spectral reflectance measurements, and occur in similar frequencies as in males. These results indicate that the influence of testosterone differs for different colours, suggesting that their expression may be governed by different proximate hormonal mechanisms. Thus, caution must be exercised when using artificial testosterone manipulation to induce female expression of sex-limited colour polymorphisms. Nevertheless, the ability to express sex-limited colours (in this case orange) to reveal the same, objectively classifiable morphs in similar frequencies to males suggests autosomal rather than sex-linked inheritance, and can facilitate further research on the genetic basis of colour polymorphism, including estimating heritability and selection on colour morphs from pedigree data. PMID:26485705

Quantifying deficits in the perception of fear and anger in morphed facial expressions after bilateral amygdala damage.

PubMed

Graham, Reiko; Devinsky, Orrin; Labar, Kevin S

2007-01-07

Amygdala damage has been associated with impairments in perceiving facial expressions of fear. However, deficits in perceiving other emotions, such as anger, and deficits in perceiving emotion blends have not been definitively established. One possibility is that methods used to index expression perception are susceptible to heuristic use, which may obscure impairments. To examine this, we adapted a task used to examine categorical perception of morphed facial expressions [Etcoff, N. L., & Magee, J. J. (1992). Categorical perception of facial expressions. Cognition, 44(3), 227-240]. In one version of the task, expressions were categorized with unlimited time constraints. In the other, expressions were presented with limited exposure durations to tap more automatic aspects of processing. Three morph progressions were employed: neutral to anger, neutral to fear, and fear to anger. Both tasks were administered to a participant with bilateral amygdala damage (S.P.), age- and education-matched controls, and young controls. The second task was also administered to unilateral temporal lobectomy patients. In the first version, S.P. showed impairments relative to normal controls on the neutral-to-anger and fear-to-anger morphs, but not on the neutral-to-fear morph. However, reaction times suggested that speed-accuracy tradeoffs could account for results. In the second version, S.P. showed impairments on all morph types relative to all other subject groups. A third experiment showed that this deficit did not extend to the perception of morphed identities. These results imply that when heuristics use is discouraged on tasks utilizing subtle emotion transitions, deficits in the perception of anger and anger/fear blends, as well as fear, are evident with bilateral amygdala damage.

Shape, colour plasticity, and habitat use indicate morph-specific camouflage strategies in a marine shrimp.

PubMed

Duarte, Rafael C; Stevens, Martin; Flores, Augusto A V

2016-10-18

Colour and shape polymorphisms are important features of many species and may allow individuals to exploit a wider array of habitats, including through behavioural differences among morphs. In addition, differences among individuals in behaviour and morphology may reflect different strategies, for example utilising different approaches to camouflage. Hippolyte obliquimanus is a small shrimp species inhabiting different shallow-water vegetated habitats. Populations comprise two main morphs: homogeneous shrimp of variable colour (H) and transparent individuals with coloured stripes (ST). These morphs follow different distribution patterns between their main algal habitats; the brown weed Sargassum furcatum and the pink-red weed Galaxaura marginata. In this study, we first investigated morph-specific colour change and habitat selection, as mechanisms underlying camouflage and spatial distribution patterns in nature. Then, we examined habitat fidelity, mobility, and morphological traits, further indicating patterns of habitat use. H shrimp are capable of changing colour in just a few days towards their algal background, achieving better concealment in the more marginal, and less preferred, red weed habitat. Furthermore, laboratory trials showed that habitat fidelity is higher for H shrimp, whereas swimming activity is higher for the ST morph, aligned to morphological evidence indicating these two morphs comprise a more benthic (H) and a more pelagic (ST) life-style, respectively. Results suggest that H shrimp utilise a camouflage strategy specialised to a limited number of backgrounds at any one time, whereas ST individuals comprise a phenotype with more generalist camouflage (transparency) linked to a more generalist background utilisation. The coexistence within a population of distinct morphotypes with apparently alternative strategies of habitat use and camouflage may reflect differential responses to substantial seasonal changes in macroalgal cover. Our findings also demonstrate how colour change, behaviour, morphology, and background use all interact in achieving camouflage.

Characterization of a Chlamydomonas Insertional Mutant that Disrupts Flagellar Central Pair Microtubule-associated Structures

PubMed Central

Mitchell, David R.; Sale, Winfield S.

1999-01-01

Two alleles at a new locus, central pair–associated complex 1 (CPC1), were selected in a screen for Chlamydomonas flagellar motility mutations. These mutations disrupt structures associated with central pair microtubules and reduce flagellar beat frequency, but do not prevent changes in flagellar activity associated with either photophobic responses or phototactic accumulation of live cells. Comparison of cpc1 and pf6 axonemes shows that cpc1 affects a row of projections along C1 microtubules distinct from those missing in pf6, and a row of thin fibers that form an arc between the two central pair microtubules. Electron microscopic images of the central pair in axonemes from radial spoke–defective strains reveal previously undescribed central pair structures, including projections extending laterally toward radial spoke heads, and a diagonal link between the C2 microtubule and the cpc1 projection. By SDS-PAGE, cpc1 axonemes show reductions of 350-, 265-, and 79-kD proteins. When extracted from wild-type axonemes, these three proteins cosediment on sucrose gradients with three other central pair proteins (135, 125, and 56 kD) in a 16S complex. Characterization of cpc1 provides new insights into the structure and biochemistry of the central pair apparatus, and into its function as a regulator of dynein-based motility. PMID:9922455

Possible utilization of acrylic paint and copper phthalocyanine pigment sludge for vermiculture.

PubMed

Majumdar, Deepanjan; Buch, Vaidehi; Macwan, Praisy; Patel, Jignesh

2010-05-01

Sludge generated from water treatment plants in two different paint and pigment manufacturing industries, one manufacturing CPC Green (copper phthalocyanine green) and the other acrylic (pure and styrene) washable distempers, synthetic enamels, fillers and putties, were used for culturing earthworms (Eisenia foetida Savigny). The possibility of getting a quality vermicompost was also explored. The sludges were used pure and mixed with month-old cow dung at 1:1, 1:2, 1:3, 2:1 and 3:1 ratios (sludge:cow dung). In pure sludges and in the 3:1 ratio, earthworms did not survive. Earthworms had very low survival in CPC Green sludge and its mixtures while acrylic paint sludge was very efficient in supporting worm growth and worm castings were generated quickly. Both sludges were alkaline, non-saline, but had appreciable Ca, Al, Pb, Zn, and Mn. CPC Green had high Cu (12,900 mg kg(-1)) and acrylic paint sludge had high total Cr (155 mg kg(-1)). High Ca and Al in both came from water treatment chemicals (lime and alum), while CPC Green itself is a copper-based pigment. The sludges were suitable for land application with regard to their metal contents, except for Cu in CPC Green. CPC Green did not support proper growth of plants (green gram, Vigna radiata (L). R. Wilcz.), while acrylic paint sludge supported growth in pure form and mixtures with soil.

Contralateral cortico-ponto-cerebellar pathways reconstruction in humans in vivo: implications for reciprocal cerebro-cerebellar structural connectivity in motor and non-motor areas.

PubMed

Palesi, Fulvia; De Rinaldis, Andrea; Castellazzi, Gloria; Calamante, Fernando; Muhlert, Nils; Chard, Declan; Tournier, J Donald; Magenes, Giovanni; D'Angelo, Egidio; Gandini Wheeler-Kingshott, Claudia A M

2017-10-09

Cerebellar involvement in cognition, as well as in sensorimotor control, is increasingly recognized and is thought to depend on connections with the cerebral cortex. Anatomical investigations in animals and post-mortem humans have established that cerebro-cerebellar connections are contralateral to each other and include the cerebello-thalamo-cortical (CTC) and cortico-ponto-cerebellar (CPC) pathways. CTC and CPC characterization in humans in vivo is still challenging. Here advanced tractography was combined with quantitative indices to compare CPC to CTC pathways in healthy subjects. Differently to previous studies, our findings reveal that cerebellar cognitive areas are reached by the largest proportion of the reconstructed CPC, supporting the hypothesis that a CTC-CPC loop provides a substrate for cerebro-cerebellar communication during cognitive processing. Amongst the cerebral areas identified using in vivo tractography, in addition to the cerebral motor cortex, major portions of CPC streamlines leave the prefrontal and temporal cortices. These findings are useful since provide MRI-based indications of possible subtending connectivity and, if confirmed, they are going to be a milestone for instructing computational models of brain function. These results, together with further multi-modal investigations, are warranted to provide important cues on how the cerebro-cerebellar loops operate and on how pathologies involving cerebro-cerebellar connectivity are generated.

Decontamination methods for samples preserved in cetylpyridinium chloride and cultured on thin-layer agar.

PubMed

Ardizzoni, E; Mulders, W; Sanchez-Padilla, E; Varaine, F; de Jong, B C; Rigouts, L

2014-08-01

Long transportation times of samples to culture laboratories can lead to higher contamination rates and significant loss of viability, resulting in lower culture positivity rates. Thin-layer agar (TLA) is a sensitive culture method for the isolation of Mycobacterium tuberculosis that has been optimised with N-acetyl-L-cysteine-sodium hydroxide (NALC-NaOH) decontaminated samples. The combination of the TLA culture method and other decontamination procedures has not been extensively validated. Among 390 smear-positive samples, we compared the culture positivity of samples decontaminated using the Petroff method vs. NALC-NaOH neutralised with phosphate buffer (PBS), applied to samples preserved with cetylpyridinium chloride (CPC) or CPC-free, and then of CPC-preserved samples decontaminated with NALC-NaOH neutralised using Difco neutralising buffer. The sediments were inoculated on TLA, and then on MGIT 960 or Löwenstein-Jensen (LJ) as gold standards. Decontamination with NALC-NaOH yielded higher culture positivity in TLA than in the Petroff method, which was further enhanced by neutralising CPC with the Difco buffer. Surprisingly, culture positivity on LJ also increased after using Difco buffer, suggesting that CPC may not be completely neutralised in egg-based medium. After transportation in CPC, decontamination using NALC-NaOH followed by neutralisation using Difco buffer resulted in the best recovery rates for samples inoculated on TLA and on LJ.

Body size evolution of a shell-brooding cichlid fish from Lake Tanganyika.

PubMed

Takahashi, T; Ota, K

2016-12-01

The substrate-brooding cichlid fish Telmatochromis temporalis in Lake Tanganyika demonstrates a simple example of ecological speciation between normal and dwarf morphs through divergent natural selection on body size. The dwarf morph most likely evolved from the ancestral normal morph; therefore, elucidating the evolution of its small body size is a key to understanding this ecological speciation event. Previous studies suggest that the small body size of the dwarf morph is an adaptation to the use of empty snail shells as shelters (males) and spawning sites (females), but this idea has not been fully evaluated. Combining original and previously published information, this study compared likelihood values to determine the primary factor that would be responsible for regulating the body size of the dwarf morph. Male body size is most likely regulated by the ability to turn within shells, which may influence the predation avoidance of adult fish. Females are smaller than males, and their body size is most likely regulated by the ability to lay eggs in the small spaces within shells close to the shell apices where predation risk on eggs is lower. This study provides new evidence supporting the hypothesis that different natural selection factors affected body size of the different sexes of the dwarf morph, which has not been reported in other animal species. © 2016 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2016 European Society For Evolutionary Biology.

Morphing the feature-based multi-blocks of normative/healthy vertebral geometries to scoliosis vertebral geometries: development of personalized finite element models.

PubMed

Hadagali, Prasannaah; Peters, James R; Balasubramanian, Sriram

2018-03-01

Personalized Finite Element (FE) models and hexahedral elements are preferred for biomechanical investigations. Feature-based multi-block methods are used to develop anatomically accurate personalized FE models with hexahedral mesh. It is tedious to manually construct multi-blocks for large number of geometries on an individual basis to develop personalized FE models. Mesh-morphing method mitigates the aforementioned tediousness in meshing personalized geometries every time, but leads to element warping and loss of geometrical data. Such issues increase in magnitude when normative spine FE model is morphed to scoliosis-affected spinal geometry. The only way to bypass the issue of hex-mesh distortion or loss of geometry as a result of morphing is to rely on manually constructing the multi-blocks for scoliosis-affected spine geometry of each individual, which is time intensive. A method to semi-automate the construction of multi-blocks on the geometry of scoliosis vertebrae from the existing multi-blocks of normative vertebrae is demonstrated in this paper. High-quality hexahedral elements were generated on the scoliosis vertebrae from the morphed multi-blocks of normative vertebrae. Time taken was 3 months to construct the multi-blocks for normative spine and less than a day for scoliosis. Efforts taken to construct multi-blocks on personalized scoliosis spinal geometries are significantly reduced by morphing existing multi-blocks.

Designing an antibacterial acrylic resin using the cosolvent method -Effect of ethanol on the optical and mechanical properties of a cold-cure acrylic resin.

PubMed

Nezu, Takashi; Nagano-Takebe, Futami; Endo, Kazuhiko

2017-09-26

Antimicrobial cetylpyridinium chloride (CPC) has low miscibility with acrylic resin monomer but can be homogeneously mixed using ethanol as a cosolvent. This study investigated the effects of ethanol addition on the properties of a cold-cure acrylic resin. Ethanol was an excellent cosolvent for CPC and methyl methacrylate monomer (MMA), but the cured resin exhibited a strong change in coloration to yellow (ΔE* ab >8) and a drastically reduced bending strength (from 97 to 25 MPa) and elastic modulus (from 2.7 to 0.6 GPa) when equal volumes of ethanol and monomer were used together, possibly due to the solvation and deactivation of radicals by ethanol. However, these unfavorable effects diminished when the ethanol/MMA ratio was reduced to 0.25, and became smaller when each specimen was depressurized and excess ethanol was removed. Thus, it may be possible to develop a molecularly uniform antibacterial acrylic resin with acceptable color and strength using this simple technique.

Development of a morphing structure with the incorporation of central pattern generators

NASA Astrophysics Data System (ADS)

Bliss, Thomas K.; Bart-Smith, Hilary; Iwasaki, Tetsuya

2006-03-01

The Manta Ray, Manta birostris, is an amazing creature, propelling itself through the water with the elegant and complex flapping of its wings. Achieving outstanding efficiencies, engineers are looking for ways to mimic its flight through the water and harness its propulsive techniques. This study combines two biologically inspired aspects to achieve this goal: morphing structures actuated with a biomimetic neural network control system. It is believed that this combination will prove capable of producing the oscillatory motions necessary for locomotion. In this paper, a four-truss structure with three actuators is chosen and its performance capabilities are analyzed. A synthetic central pattern generator, which provides the fundamental control mechanisms for rhythmic motion in animals, is designed to realize an oscillatory control of the three actuators. The control system is simulated using Matlab, then combined with LabVIEW to control the four-truss structure. The system's performance is analyzed, with specific attention to both transient and steady-state behavior.

morph

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goodall, John; Iannacone, Mike; Athalye, Anish

2013-08-01

Morph is a framework and domain-specific language (DSL) that helps parse and transform structured documents. It currently supports several file formats including XML, JSON, and CSV, and custom formats are usable as well.

Microencapsulation of pulp and ultrafiltered cactus pear (Opuntia ficus-indica) extracts and betanin stability during storage.

PubMed

Vergara, Cristina; Saavedra, Jorge; Sáenz, Carmen; García, Paula; Robert, Paz

2014-08-15

Pulp (CP) and ultrafiltered (UF) cactus pear extracts were encapsulated with Capsul (C) by applying a central composite design (CP-C and UF-C systems) by spray-drying. To evaluate the effect of the extract, microparticles obtained under optimal conditions were characterised and stored at 60 °C. Betacyanin and betaxanthin encapsulation efficiency reached values above 98% for both systems studied. This efficiency was attributed to strong interactions between betalains and the polymer. Betalain degradation in CP-C and UF-C microparticles followed pseudo-first order kinetics. The betacyanin degradation rate constant was significantly higher for CP-C than for UF-C. These results suggested that the mucilage or higher sugar content of CP increased the hygroscopicity of the CP-C microparticles, leading to the degradation of betalain. The hydrolysis pathway was the main mechanism of betanin degradation during microparticle storage. These results demonstrate the potential utility of both CP-C and UF-C microparticles as natural colourants for healthy foods. Copyright © 2014 Elsevier Ltd. All rights reserved.

In vitro CPC retention and VSC adsorption by IPM oil droplets: possible mechanisms of action of a two phase mouthwash.

PubMed

Sterer, N; Slutzky, H; Kohavi, D; Matalon, S

2013-09-01

Two phase oil-water mouthwash has been previously shown to efficiently bind oral microorganisms, relying on their cell surface hydrophobicity. The aim of the present in vitro study was to test the cetylpyridinium chloride (CPC) retention and volatile sulfide compounds (VSCs) adsorption abilities of the oil droplets created by mixing of a two phase oil-water solution. VSC adsorption was assayed using a salivary incubation assay and garlic powder solutions, and demonstrated using microscopic sulfide assay. CPC retention was assayed by kinetic and endpoint measurement of Streptococcus salivarius outgrowth using microplate (ELISA) reader. Results showed that the isopropyl myristate (IPM) oil droplets in the two phase solutions were able to adsorb 68-80% of VSCs. CPC at a concentration of 0.05% was most affectively retained by the oil droplets showing a significantly increase in residual antibacterial activity against Streptococcus salivarius. These results taken together, suggests that VSC adsorption and CPC retention by IPM oil droplets may be two additional mechanisms in the activity of the two phase mouthwash formulation.

The performance of solar collector CPC (compound parabolic concentrator) type with three pipes covered by glass tubes

NASA Astrophysics Data System (ADS)

Gaos, Yogi Sirodz; Yulianto, Muhamad; Juarsa, Mulya; Nurrohman, Marzuki, Edi; Yuliaji, Dwi; Budiono, Kabul

2017-03-01

Indonesia is a tropical country that has potential energy of solar radiation worth of 4.5 until 4.8 kWh/m2. However, this potential has not been utilized regularly. This paper will discuss the performance of solar collector compound parabolic concentrator (CPC) type with water as the working fluid. This CPC solar collector utilized three pipes covered by glass tubes. This paper has contribution to provide the temperature achievement between three pipes covered by glass tubes with and without glass cover of solar collector CPC type. The research conducted by varying the water flow rate of 1 l/m up to 6 l/m with three pipes arranged in series and parallel. From the results, the used of solar collector CPC type in the current study shows that the decrease of solar radiation, which was caused by climate change, did not influence the heat absorbance by water in the pipe. Therefore, the design of the solar collector in this research has potential to be used in future when solar radiation are used as the energy source.

Application of cetylpyridinium chloride and sodium chloride decontamination method for recovery of Mycobacterium tuberculosis from clinically suspected cases of pulmonary tuberculosis.

PubMed

Shinu, Pottathil; Singh, Varsha; Nair, Anroop; Mehrishi, Priya; Mehta, Sonia; Joshi, Ekta

2013-10-01

The study was designed to compare the efficacy of cetylpyridinium chloride (CPC) and sodium chloride (NaCl) decontamination method with N-acetyl L-Cystine (NALC) and sodium hydroxide (NaOH) decontamination (the reference method) method for the recovery of Mycobacterium tuberculosis (MTB) from clinically suspected cases of pulmonary tuberculosis. To evaluate CPC-NaCl and NALC-NaOH decontamination methods, sputum specimens (n = 796) were studied (culturing on Löwenstein-Jensen medium), and the performances were compared. The CPC-NaCl decontamination method demonstrated a sensitivity, specificity, negative predictive value, and positive predictive value of 97.99%, 87.53%, 70.19%, and 99.32%, respectively, when compared to NALC-NaOH decontamination method. In summary, CPC-NaCl decontamination method effectively detected significantly higher number of MTB cases (n = 208) than NALC-NaOH decontamination method (n = 149) particularly in sputum with scanty bacilli and smear-negative cases, indicating the potential of CPC-NaCl decontamination method to preserve paucibacillary cases more efficient than NALC-NaOH decontamination method. © 2013.

Centrifugal partition chromatography enables selective enrichment of trimeric and tetrameric proanthocyanidins for biomaterial development.

PubMed

Phansalkar, Rasika S; Nam, Joo-Won; Chen, Shao-Nong; McAlpine, James B; Leme, Ariene A; Aydin, Berdan; Bedran-Russo, Ana-Karina; Pauli, Guido F

2018-02-02

Proanthocyanidins (PACs) find wide applications for human use including food, cosmetics, dietary supplements, and pharmaceuticals. The chemical complexity associated with PACs has triggered the development of various chromatographic techniques, with countercurrent separation (CCS) gaining in popularity. This study applied the recently developed DESIGNER (Depletion and Enrichment of Select Ingredients Generating Normalized Extract Resources) approach for the selective enrichment of trimeric and tetrameric PACs using centrifugal partition chromatography (CPC). This CPC method aims at developing PAC based biomaterials, particularly for their application in restoring and repairing dental hard tissue. A general separation scheme beginning with the depletion of polymeric PACs, followed by the removal of monomeric flavan-3-ols and a final enrichment step produced PAC trimer and tetramer enriched fractions. A successful application of this separation scheme is demonstrated for four polyphenol rich plant sources: grape seeds, pine bark, cinnamon bark, and cocoa seeds. Minor modifications to the generic DESIGNER CCS method were sufficient to accommodate the varying chemical complexities of the individual source materials. The step-wise enrichment of PAC trimers and tetramers was monitored using normal phase TLC and Diol-HPLC-UV analyses. CPC proved to be a reliable tool for the selective enrichment of medium size oligomeric PACs (OPACs). This method plays a key role in the development of dental biomaterials considering its reliability and reproducibility, as well as its scale-up capabilities for possible larger-scale manufacturing. Copyright © 2017 Elsevier B.V. All rights reserved.

Tantalum oxide and barium sulfate as radiopacifiers in injectable calcium phosphate-poly(lactic-co-glycolic acid) cements for monitoring in vivo degradation.

PubMed

Hoekstra, Jan Willem M; van den Beucken, Jeroen J J P; Leeuwenburgh, Sander C G; Bronkhorst, Ewald M; Meijer, Gert J; Jansen, John A

2014-01-01

Monitoring the degradation of calcium phosphate-based bone substitute materials in vivo by means of noninvasive techniques (e.g., radiography) is often a problem due to the chemical resemblance of those substitutes with the mineral phase of bone. In the view of that, the present study aimed at enhancing the radiopacity of calcium phosphate cement enriched with poly(lactic-co-glycolic acid) (CPC-PLGA) microspheres, by adding tantalum oxide (Ta2O5) or the more traditional radiopacifier barium sulfate (BaSO4). The radiopacifying capacity of these radiopacifiers was first evaluated in vitro by microcomputed tomography (μCT). Thereafter, both radiopacifiers were tested in vivo using a distal femoral condyle model in rabbits, with subsequent ex vivo μCT analysis in parallel with histomorphometry. Addition of either one of the radiopacifiers proved to enhance radiopacity of CPC-PLGA in vitro. The in vivo experiment showed that both radiopacifiers did not induce alterations in biological performance compared to plain CPC-PLGA, hence both radiopacifiers can be considered safe and biocompatible. The histomorphometrical assessment of cement degradation and bone formation showed similar values for the three experimental groups. Interestingly, μCT analysis showed that monitoring cement degradation becomes feasible upon incorporation of either type of radiopacifier, albeit that BaSO4 showed more accuracy compared to Ta2O5. Copyright © 2013 Wiley Periodicals, Inc., a Wiley Company.

New Insights on Insect's Silent Flight. Part I: Vortex Dynamics and Wing Morphing

NASA Astrophysics Data System (ADS)

Ren, Yan; Liu, Geng; Dong, Haibo; Geng, Biao; Zheng, Xudong; Xue, Qian

2016-11-01

Insects are capable of conducting silent flights. This is attributed to its specially designed wing material properties for the control of vibration and surface morphing during the flapping flight. In current work, we focus on the roles of dynamic wing morphing on the unsteady vortex dynamics of a cicada in steady flight. A 3D image-based surface reconstruction method is used to obtain kinematical and morphological data of cicada wings from high-quality high-speed videos. The observed morphing wing kinematics is highly complex and a singular value decomposition method is used to decompose the wing motion to several dominant modes with distinct motion features. A high-fidelity immersed-boundary-based flow solver is then used to study the vortex dynamics in details. The results show that vortical structures closely relate to the morphing mode, which plays key role in the development and attachment of leading-edge vortex (LEV), thus helps the silent flapping of the cicada wings. This work is supported by AFOSR FA9550-12-1-0071 and NSF CBET-1313217.

Novel deployable morphing wing based on SMP composite

NASA Astrophysics Data System (ADS)

Yu, Kai; Sun, Shouhua; Liu, Liwu; Zhang, Zhen; Liu, Yanju; Leng, Jinsong

2009-07-01

In this paper, a novel kind of deployable morphing wing base on shape memory polymer (SMP) composite is designed and tested. While the deployment of the morphing wing still relies on the mechanisms to ensure the recovery force and the stability performance, the deploying process tends to be more steady and accurate by the application of SMP composite, which overcomes the inherent drawbacks of the traditional one, such as harmful impact to the flight balance, less accuracy during the deployment and complex mechanical masses. On the other hand, SMP composite is also designed as the wing's filler. During its shape recovery process, SMP composite stuffed in the wing helps to form an aerofoil for the wing and withstand the aerodynamic loads, leading to the compressed aerofoil recovering its original shape. To demonstrate the feasibility and the controllability of the designed deployable morphing wing, primary tests are also conducted, including the deploying speed of the morphing wing and SMP filler as the main testing aspects. Finally, Wing's deformation under the air loads is also analyzed by using the finite element method to validate the flight stability.

Structural design of morphing trailing edge actuated by SMA

NASA Astrophysics Data System (ADS)

Wang, Qi; Xu, Zhiwei; Zhu, Qian

2013-09-01

In this paper, the morphing trailing edge is designed to achieve the up and down deflection under the aerodynamic load. After a detailed and accurate computational analysis to determine the SMA specifications and layout programs, a solid model is created in CATIA and the structures of the morphing wing trailing edge are produced by CNC machining. A set of DSP measurement and control system is designed to accomplish the controlling experiment of the morphing wing trailing edge. At last, via the force analysis, the trailing edge is fabricated with four sections of aluminum alloy, and the arrangement scheme of SMA wires is determined. Experiment of precise control integral has been performed to survey the control effect. The experiment consists of deflection angle tests of the third joint and the integral structure. Primarily, the ultimate deflection angle is tested in these two experiments. Therefore, the controlling experiment of different angles could be performed within this range. The results show that the deflection error is less than 4%and response time is less than 6.7 s, the precise controlling of the morphing trailing edge is preliminary realized.

Biomechanics of smart wings in a bat robot: morphing wings using SMA actuators.

PubMed

Colorado, J; Barrientos, A; Rossi, C; Bahlman, J W; Breuer, K S

2012-09-01

This paper presents the design of a bat-like micro aerial vehicle with actuated morphing wings. NiTi shape memory alloys (SMAs) acting as artificial biceps and triceps muscles are used for mimicking the morphing wing mechanism of the bat flight apparatus. Our objective is twofold. Firstly, we have implemented a control architecture that allows an accurate and fast SMA actuation. This control makes use of the electrical resistance measurements of SMAs to adjust morphing wing motions. Secondly, the feasibility of using SMA actuation technology is evaluated for the application at hand. To this purpose, experiments are conducted to analyze the control performance in terms of nominal and overloaded operation modes of the SMAs. This analysis includes: (i) inertial forces regarding the stretchable wing membrane and aerodynamic loads, and (ii) uncertainties due to impact of airflow conditions over the resistance-motion relationship of SMAs. With the proposed control, morphing actuation speed can be increased up to 2.5 Hz, being sufficient to generate lift forces at a cruising speed of 5 m s(-1).

Visual one-shot learning as an 'anti-camouflage device': a novel morphing paradigm.

PubMed

Ishikawa, Tetsuo; Mogi, Ken

2011-09-01

Once people perceive what is in the hidden figure such as Dallenbach's cow and Dalmatian, they seldom seem to come back to the previous state when they were ignorant of the answer. This special type of learning process can be accomplished in a short time, with the effect of learning lasting for a long time (visual one-shot learning). Although it is an intriguing cognitive phenomenon, the lack of the control of difficulty of stimuli presented has been a problem in research. Here we propose a novel paradigm to create new hidden figures systematically by using a morphing technique. Through gradual changes from a blurred and binarized two-tone image to a blurred grayscale image of the original photograph including objects in a natural scene, spontaneous one-shot learning can occur at a certain stage of morphing when a sufficient amount of information is restored to the degraded image. A negative correlation between confidence levels and reaction times is observed, giving support to the fluency theory of one-shot learning. The correlation between confidence ratings and correct recognition rates indicates that participants had an accurate introspective ability (metacognition). The learning effect could be tested later by verifying whether or not the target object was recognized quicker in the second exposure. The present method opens a way for a systematic production of "good" hidden figures, which can be used to demystify the nature of visual one-shot learning.

Centrifugal partition chromatography a first dimension for biomass fast pyrolysis oil analysis.

PubMed

Le Masle, Agnès; Santin, Sandra; Marlot, Léa; Chahen, Ludovic; Charon, Nadège

2018-10-31

Biomass fast pyrolysis oils contain molecules having a large variety of chemical functions and a wide range of molecular weights (from several tens to several thousand grams per mole). The good knowledge of their complex composition is essential for optimizing the conversion of bio-oils to biofuels, thereby requiring powerful separation techniques. In this work, we investigate the interest of centrifugal partition chromatography (CPC) as a first dimension for the analysis of a bio-oil. A CPC method is proposed to separate oxygen containing compounds according to their partition coefficients in the solvent system. This approach is a powerful and easy-to-use technique that enables fractionation of a bio-oil at a semi-preparative scale, without any sample loss related to adsorption on the stationary phase. Collected fractions are then injected in liquid chromatography as a second dimension of separation. Contour plot representations of the CPC × LC separation are established to discuss the potential of this approach. These representations can be used as a veritable fingerprint in the comparison of different samples or samples at different steps of a conversion process but also as a powerful tool to identify new compounds and describe the entire composition of the bio-oil. Copyright © 2018 Elsevier B.V. All rights reserved.

Statistical analysis of whole-body absorption depending on anatomical human characteristics at a frequency of 2.1 GHz.

PubMed

Habachi, A El; Conil, E; Hadjem, A; Vazquez, E; Wong, M F; Gati, A; Fleury, G; Wiart, J

2010-04-07

In this paper, we propose identification of the morphological factors that may impact the whole-body averaged specific absorption rate (WBSAR). This study is conducted for the case of exposure to a front plane wave at a 2100 MHz frequency carrier. This study is based on the development of different regression models for estimating the WBSAR as a function of morphological factors. For this purpose, a database of 12 anatomical human models (phantoms) has been considered. Also, 18 supplementary phantoms obtained using the morphing technique were generated to build the required relation. This paper presents three models based on external morphological factors such as the body surface area, the body mass index or the body mass. These models show good results in estimating the WBSAR (<10%) for families obtained by the morphing technique, but these are still less accurate (30%) when applied to different original phantoms. This study stresses the importance of the internal morphological factors such as muscle and fat proportions in characterization of the WBSAR. The regression models are then improved using internal morphological factors with an estimation error of approximately 10% on the WBSAR. Finally, this study is suitable for establishing the statistical distribution of the WBSAR for a given population characterized by its morphology.

Statistical analysis of whole-body absorption depending on anatomical human characteristics at a frequency of 2.1 GHz

NASA Astrophysics Data System (ADS)

El Habachi, A.; Conil, E.; Hadjem, A.; Vazquez, E.; Wong, M. F.; Gati, A.; Fleury, G.; Wiart, J.

2010-04-01

In this paper, we propose identification of the morphological factors that may impact the whole-body averaged specific absorption rate (WBSAR). This study is conducted for the case of exposure to a front plane wave at a 2100 MHz frequency carrier. This study is based on the development of different regression models for estimating the WBSAR as a function of morphological factors. For this purpose, a database of 12 anatomical human models (phantoms) has been considered. Also, 18 supplementary phantoms obtained using the morphing technique were generated to build the required relation. This paper presents three models based on external morphological factors such as the body surface area, the body mass index or the body mass. These models show good results in estimating the WBSAR (<10%) for families obtained by the morphing technique, but these are still less accurate (30%) when applied to different original phantoms. This study stresses the importance of the internal morphological factors such as muscle and fat proportions in characterization of the WBSAR. The regression models are then improved using internal morphological factors with an estimation error of approximately 10% on the WBSAR. Finally, this study is suitable for establishing the statistical distribution of the WBSAR for a given population characterized by its morphology.

Pressure-actuated cellular structures.

PubMed

Pagitz, M; Lamacchia, E; Hol, J M A M

2012-03-01

Shape changing structures will play an important role in future engineering designs since rigid structures are usually only optimal for a small range of service conditions. Hence, a concept for reliable and energy-efficient morphing structures that possess a large strength to self-weight ratio would be widely applicable. We propose a novel concept for morphing structures that is inspired by the nastic movement of plants. The idea is to connect prismatic cells with tailored pentagonal and/or hexagonal cross sections such that the resulting cellular structure morphs into given target shapes for certain cell pressures. An efficient algorithm for computing equilibrium shapes as well as cross-sectional geometries is presented. The potential of this novel concept is demonstrated by several examples that range from a flagellum like propulsion device to a morphing aircraft wing.

The Influence of Social Comparison on Visual Representation of One's Face

PubMed Central

Zell, Ethan; Balcetis, Emily

2012-01-01

Can the effects of social comparison extend beyond explicit evaluation to visual self-representation—a perceptual stimulus that is objectively verifiable, unambiguous, and frequently updated? We morphed images of participants' faces with attractive and unattractive references. With access to a mirror, participants selected the morphed image they perceived as depicting their face. Participants who engaged in upward comparison with relevant attractive targets selected a less attractive morph compared to participants exposed to control images (Study 1). After downward comparison with relevant unattractive targets compared to control images, participants selected a more attractive morph (Study 2). Biased representations were not the products of cognitive accessibility of beauty constructs; comparisons did not influence representations of strangers' faces (Study 3). We discuss implications for vision, social comparison, and body image. PMID:22662124

The morphing of geographical features by Fourier transformation.

PubMed

Li, Jingzhong; Liu, Pengcheng; Yu, Wenhao; Cheng, Xiaoqiang

2018-01-01

This paper presents a morphing model of vector geographical data based on Fourier transformation. This model involves three main steps. They are conversion from vector data to Fourier series, generation of intermediate function by combination of the two Fourier series concerning a large scale and a small scale, and reverse conversion from combination function to vector data. By mirror processing, the model can also be used for morphing of linear features. Experimental results show that this method is sensitive to scale variations and it can be used for vector map features' continuous scale transformation. The efficiency of this model is linearly related to the point number of shape boundary and the interceptive value n of Fourier expansion. The effect of morphing by Fourier transformation is plausible and the efficiency of the algorithm is acceptable.

The role of calcium and predation on plate morph evolution in the three-spined stickleback (Gasterosteus aculeatus).

PubMed

Smith, Carl; Spence, Rowena; Barber, Iain; Przybylski, Mirosław; Wootton, Robert J

2014-09-01

While the genetic basis to plate morph evolution of the three-spined stickleback (Gasterosteus aculeatus) is well described, the environmental variables that select for different plate and spine morphs are incompletely understood. Using replicate populations of three-spined sticklebacks on North Uist, Scotland, we previously investigated the role of predation pressure and calcium limitation on the adaptive evolution of stickleback morphology and behavior. While dissolved calcium proved a significant predictor of plate and spine morph, predator abundance did not. Ecol. Evol., xxx, 2014 and xxx performed a comparable analysis to our own to address the same question. They failed to detect a significant effect of dissolved calcium on morphological evolution, but did establish a significant effect of predation; albeit in the opposite direction to their prediction.

Dielectric compound parabolic concentrating solar collector with frustrated total internal reflection absorber

NASA Astrophysics Data System (ADS)

Hull, J. R.

Since its introduction, the concept of nonimaging solar concentrators, as exemplified by the compound parabolic concentrator (CPC) design, has greatly enhanced the ability to collect solar energy efficiently in thermal and photovoltaic devices. When used as a primary concentrator, a CPC can provide significant concentration without the complication of a tracking mechanism and its associated maintenance problems. When used as a secondary, a CPC provides higher total concentration, or for a fixed concentration, tolerates greater tracking error in the primary.

A FSI Enabled Practical Rotorcraft Flow Simulator for Morphing Blade Innovation

DTIC Science & Technology

2015-05-08

morphing surface at different azimuthal angles . It can be found that the morphing surfaces do not deform at 0º and 22.5º, because the shock is...Apparently, due to the superposition of two speeds, the position and strength of shock change at different azimuthal angles . As shown in Figure 30, the...meters. The observer is stationary and the blade rotates periodically. This set up follows what would essentially be a wind tunnel set up. The blade

Two-dimensional multi-heart cutting centrifugal partition chromatography-liquid chromatography for the preparative isolation of antioxidants from Edelweiss plant.

PubMed

Marlot, Léa; Batteau, Magali; Escofet, Marie-Claire; Nuccio, Sylvie; Coquoin, Véronique; De Vaumas, René; Faure, Karine

2017-06-30

The Edelweiss plant has been recognized as a very valuable source of anti-aging principles due to its composition of antioxidants compounds: leontopodic acid A and 3,5-dicaffeoylquinic acid. In this work, off-line multi-heart cutting CPC-LC separation was set up at industrial scale in order to isolate and produce new high quality reference material of these two antioxidants from Edelweiss. For this purpose, CPC and HPLC methods were developed and optimized at laboratory scale and a comprehensive CPCxHPLC analysis of the crude extract was established. Thereby, the CPC method led to a first separation of the target compounds according to their partition coefficient in the solvent system and the HPLC method was performed on the recovered fractions to lead to a second separation. A 2D CPCxHPLC plot was established in order to know the fractions to select at the industrial scale. Then, the CPC and HPLC methods were transferred at industrial scale and the multi-heart cutting CPC-LC was performed in off-line mode. Using CPC with methyl ter-butyl ether-water 1:1 (v/v) solvent system and LC with Denali C18 column, 2g of crude extract sample were injected and leontopodic acid A and 3,5-dicaffeoylquinic acid were recovered with purity over 97%. The compounds were identified by MS and NMR. Copyright © 2017 Elsevier B.V. All rights reserved.

The effectiveness of a preprocedural mouthrinse containing cetylpyridinium chloride in reducing bacteria in the dental office.

PubMed

Feres, Magda; Figueiredo, Luciene Cristina; Faveri, Marcelo; Stewart, Bernal; de Vizio, William

2010-04-01

During oral procedures, microorganisms from the oral cavity may contaminate nearby surfaces. The authors evaluated the efficacy of a commercial preprocedural mouthrinse containing 0.05 percent cetylpyridinium chloride (CPC) in reducing the levels and composition of viable bacteria in oral spatter. The authors randomly assigned 60 participants receiving oral prophylaxis with an ultrasonic scaler to one of four groups: a preprocedural rinse solution containing 0.05 percent CPC, 0.12 percent chlorhexidine (CHX) or water, or no rinsing. Airborne microorganisms were collected on blood agar plates. The composition of the spatter was analyzed for 39 oral bacterial species by means of checkerboard DNA-DNA hybridization. CPC and CHX were equally effective in lowering the levels of spatter bacteria and performed better than water and no rinsing (P < .05, Kruskal-Wallis test). The composition of the spatter from the control groups showed higher proportions (P < .05, Kruskal-Wallis test) of Fusobacterium species and lower proportions of Capnocytophaga species when compared with the spatter from the CPC and CHX groups. A commercial mouthrinse containing 0.05 percent CPC when used as a preprocedural mouthrinse was equally effective as CHX in reducing the levels of spatter bacteria generated during ultrasonic scaling. Owing to its strong antibacterial effect and the fact that it has fewer side effects than CHX, a solution containing 0.05 percent CPC may be a good alternative to that containing 0.12 CHX as a preprocedural mouthrinse used to help decrease the level of contamination in spatter.

Epidermal patterning genes are active during embryogenesis in Arabidopsis.

PubMed

Costa, Silvia; Dolan, Liam

2003-07-01

Epidermal cells in the root of Arabidopsis seedling differentiate either as hair or non-hair cells, while in the hypocotyl they become either stomatal or elongated cells. WEREWOLF (WER) and GLABRA2 (GL2) are positive regulators of non-hair and elongated cell development. CAPRICE (CPC) is a positive regulator of hair cell development in the root. We show that WER, GL2 and CPC are expressed and active during the stages of embryogenesis when the pattern of cells in the epidermis of the root-hypocotyl axis forms. GL2 is first expressed in the future epidermis in the heart stage embryo and its expression is progressively restricted to those cells that will acquire a non-hair identity in the transition between torpedo and mature stage. The expression of GL2 at the heart stage requires WER function. WER and CPC are transiently expressed throughout the root epidermal layer in the torpedo stage embryo when the cell-specific pattern of GL2 expression is being established in the epidermis. We also show that WER positively regulates CPC transcription and GL2 negatively regulates WER transcription in the mature embryo. We propose that the restriction of GL2 to the future non-hair cells in the root epidermis can be correlated with the activities of WER and CPC during torpedo stage. In the embryonic hypocotyl we show that WER controls GL2 expression. We also provide evidence indicating that CPC may also regulate GL2 expression in the hypocotyl.

Kinetic analysis on the skin disposition of cytotoxicity as an index of skin irritation produced by cetylpyridinium chloride: comparison of in vitro data using a three-dimensional cultured human skin model with in vivo results in hairless mice.

PubMed

Kano, Satoshi; Sugibayashi, Kenji

2006-02-01

The aim of this study was to kinetically and dynamically analyze in vitro cytotoxicity as an index of skin irritation by use of a three-dimensional cultured human skin model and to compare the in vitro assay data with data from living animals. A cationic surfactant, cetylpyridinium chloride (CPC), was selected as a model irritant. Living skin equivalent-high (LSE-high) and hairless mice were used for the in vitro and in vivo tests, respectively. Skin irritation dermatodynamics was evaluated by calorimetric thiazoyl blue (MTT) conversion assay both for in vitro and in vivo tests, whereas dermatokinetics of CPC in LSE-high and mouse skin were evaluated using HPLC. The time course of cell viability in the skin after application of CPC to intact skin was distinctly different from that of stratum-corneum-stripped skin in both LSE-high and hairless mice. Biphasic behavior characterized by two first-order rates with an inflection time point was observed in intact skin, whereas cell viability monoexponentially decreased immediately after CPC application in stripped skin. The time courses of cell viability in the skin and dermatodynamics were closely related to that of dermatokinetics of CPC. The present study demonstrates that the in vitro cytotoxic profile was similar to the in vivo cytotoxicity test and that dermatodynamics was related to dermatokinetics of CPC.

Risk Stratification Methods and Provision of Care Management Services in Comprehensive Primary Care Initiative Practices.

PubMed

Reddy, Ashok; Sessums, Laura; Gupta, Reshma; Jin, Janel; Day, Tim; Finke, Bruce; Bitton, Asaf

2017-09-01

Risk-stratified care management is essential to improving population health in primary care settings, but evidence is limited on the type of risk stratification method and its association with care management services. We describe risk stratification patterns and association with care management services for primary care practices in the Comprehensive Primary Care (CPC) initiative. We undertook a qualitative approach to categorize risk stratification methods being used by CPC practices and tested whether these stratification methods were associated with delivery of care management services. CPC practices reported using 4 primary methods to stratify risk for their patient populations: a practice-developed algorithm (n = 215), the American Academy of Family Physicians' clinical algorithm (n = 155), payer claims and electronic health records (n = 62), and clinical intuition (n = 52). CPC practices using practice-developed algorithm identified the most number of high-risk patients per primary care physician (282 patients, P = .006). CPC practices using clinical intuition had the most high-risk patients in care management and a greater proportion of high-risk patients receiving care management per primary care physician (91 patients and 48%, P =.036 and P =.128, respectively). CPC practices used 4 primary methods to identify high-risk patients. Although practices that developed their own algorithm identified the greatest number of high-risk patients, practices that used clinical intuition connected the greatest proportion of patients to care management services. © 2017 Annals of Family Medicine, Inc.

Simulation of acute haemodynamic outcomes of the surgical strategies for the right ventricular failure treatment in pediatric LVAD.

PubMed

Di Molfetta, Arianna; Ferrari, Gianfranco; Iacobelli, Roberta; Filippelli, Sergio; Fresiello, Libera; Gagliardi, Maria G; Toscano, Alessandro; Trivella, Maria G; Amodeo, Antonio

2015-12-01

Right ventricular failure (RVF) is one of the major complications during LVAD. Apart from drug therapy, the most reliable option is the implantation of RVAD. However, BIVAD have a poor prognosis and increased complications. Experiments have been conducted on alternative approaches, such as the creation of an atrial septal defect (ASD), a cavo-aortic shunt (CAS) including the LVAD and a cavo-pulmonary connection (CPC). This work aims at realizing a lumped parameter model (LPM) to compare the acute hemodynamic effects of ASD, CPC, CAS, RVAD in LVAD pediatric patients with RVF. Data of 5 pediatric patients undergoing LVAD were retrospectively collected to reproduce patients baseline hemodynamics with the LPM. The effects of continuous flow LVAD implantation complicated by RVF was simulated and then the effects of ASD, CPC, CAS and RVAD treatments were simulated for each patient. The model successfully reproduced patients' baseline and the hemodynamic effects of the surgical strategies. Simulating the different surgical strategies, an unloading of the right ventricle and an increment of left ventricular preload were observed with an improvement of the hemodynamics (total cardiac output: ASD +15%, CPC +10%, CAS +70% RVAD +20%; right ventricular external work: ASD -19%, CPC -46%, CAS -76%, RVAD -32%; left ventricular external work: ASD +12%, CPC +28%, RVAD +64%). The use of numerical model could offer an additional support for clinical decision-making, also potentially reducing animal experiments, to compare the outcome of different surgical strategies to treat RVF in LVAD.

Chromosome segregation regulation in human zygotes: altered mitotic histone phosphorylation dynamics underlying centromeric targeting of the chromosomal passenger complex.

PubMed

van de Werken, C; Avo Santos, M; Laven, J S E; Eleveld, C; Fauser, B C J M; Lens, S M A; Baart, E B

2015-10-01

Are the kinase feedback loops that regulate activation and centromeric targeting of the chromosomal passenger complex (CPC), functional during mitosis in human embryos? Investigation of the regulatory kinase pathways involved in centromeric CPC targeting revealed normal phosphorylation dynamics of histone H2A at T120 (H2ApT120) by Bub1 kinase and subsequent recruitment of Shugoshin, but phosphorylation of histone H3 at threonine 3 (H3pT3) by Haspin failed to show the expected centromeric enrichment on metaphase chromosomes in the zygote. Human cleavage stage embryos show high levels of chromosomal instability. What causes this high error rate is unknown, as mechanisms used to ensure proper chromosome segregation in mammalian embryos are poorly described. In this study, we investigated the pathways regulating CPC targeting to the inner centromere in human embryos. We characterized the distribution of the CPC in relation to activity of its two main centromeric targeting pathways: the Bub1-H2ApT120-Sgo-CPC and Haspin-H3pT3-CPC pathways. The study was conducted between May 2012 and March 2014 on human surplus embryos resulting from in vitro fertilization treatment and donated for research. In zygotes, nuclear envelope breakdown was monitored by time-lapse imaging to allow timed incubations with specific inhibitors to arrest at prometaphase and metaphase, and to interfere with Haspin and Aurora B/C kinase activity. Functionality of the targeting pathways was assessed through characterization of histone phosphorylation dynamics by immunofluorescent analysis, combined with gene expression by RT-qPCR and immunofluorescent localization of key pathway proteins. Immunofluorescent analysis of the CPC subunit Inner Centromere Protein revealed the pool of stably bound CPC proteins was not strictly confined to the inner centromere of prometaphase chromosomes in human zygotes, as observed in later stages of preimplantation development and somatic cells. Investigation of the regulatory kinase pathways involved in centromeric CPC targeting revealed normal phosphorylation dynamics of histone H2A at T120 (H2ApT120) by Bub1 kinase and subsequent recruitment of Shugoshin. However, phosphorylation of histone H3 at threonine 3 (H3pT3) by Haspin kinase failed to show the expected centromeric enrichment on metaphase chromosomes in the zygote, but not at later stages. Inhibition of Haspin revealed this activity to be essential for proper mitotic checkpoint complex activation in human zygotes, thus demonstrating an active mitotic checkpoint under normal conditions. Abolishment of H3pT3 during zygotic prometaphase further shows that centromeric H2ApT120 alone is not sufficient for proper shugoshin and CPC localization. As the removal of H3pT3 from the chromosome arms during prometaphase normally contributes to further centromeric enrichment of the CPC in somatic cells, CPC targeting may be less accurate in human zygotes. Owing to ethical limitations, tripronuclear zygotes were used in functional experiments. Although these represent the best available models, it is unknown if they are completely representative for dipronuclear zygotes. In addition, further research is needed to determine to what extent the differences we observed in H3T3 phosphorylation dynamics and CPC localization affect chromosome attachment. In the zygote, paternal and maternal chromosomes coming from two separate pronuclei, and with contrasting epigenetic signatures, need to be aligned on a single metaphase plate. Our results suggest that adaptations in mechanisms regulating CPC targeting exist in the human zygote, to ensure symmetric recruitment despite the epigenetic asymmetry between maternal and paternal chromosomes. This adaptation may come at a price regarding chromosome segregation fidelity. This study was funded by the Portuguese Fundação para a Ciência e Tecnologia and the Netherlands Organization for Scientific Research. The authors have no conflicts of interest to declare. © The Author 2015. Published by Oxford University Press on behalf of the European Society of Human Reproduction and Embryology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The morphing of geographical features by Fourier transformation

PubMed Central

Liu, Pengcheng; Yu, Wenhao; Cheng, Xiaoqiang

2018-01-01

This paper presents a morphing model of vector geographical data based on Fourier transformation. This model involves three main steps. They are conversion from vector data to Fourier series, generation of intermediate function by combination of the two Fourier series concerning a large scale and a small scale, and reverse conversion from combination function to vector data. By mirror processing, the model can also be used for morphing of linear features. Experimental results show that this method is sensitive to scale variations and it can be used for vector map features’ continuous scale transformation. The efficiency of this model is linearly related to the point number of shape boundary and the interceptive value n of Fourier expansion. The effect of morphing by Fourier transformation is plausible and the efficiency of the algorithm is acceptable. PMID:29351344

The role of calcium and predation on plate morph evolution in the three-spined stickleback (Gasterosteus aculeatus)

PubMed Central

Smith, Carl; Spence, Rowena; Barber, Iain; Przybylski, Mirosław; Wootton, Robert J

2014-01-01

While the genetic basis to plate morph evolution of the three-spined stickleback (Gasterosteus aculeatus) is well described, the environmental variables that select for different plate and spine morphs are incompletely understood. Using replicate populations of three-spined sticklebacks on North Uist, Scotland, we previously investigated the role of predation pressure and calcium limitation on the adaptive evolution of stickleback morphology and behavior. While dissolved calcium proved a significant predictor of plate and spine morph, predator abundance did not. Ecol. Evol., xxx, 2014 and xxx performed a comparable analysis to our own to address the same question. They failed to detect a significant effect of dissolved calcium on morphological evolution, but did establish a significant effect of predation; albeit in the opposite direction to their prediction. PMID:25478147

Preliminary aeroelastic assessment of a large aeroplane equipped with a camber-morphing aileron

NASA Astrophysics Data System (ADS)

Pecora, Rosario; Amoroso, Francesco; Palumbo, Rita; Arena, Maurizio; Amendola, Gianluca; Dimino, Ignazio

2017-04-01

The development of adaptive morphing wings has been individuated as one of the crucial topics in the greening of the next generation air transport. Research programs have been lunched and are still running worldwide to exploit the potentials of morphing concepts in the optimization of aircraft efficiency and in the consequent reduction of fuel burn. In the framework of CRIAQ MDO 505, a joint Canadian and Italian research project, an innovative camber morphing architecture was proposed for the aileron of a reference civil transportation aircraft; aileron shape adaptation was conceived to increase roll control effectiveness as well as to maximize overall wing efficiency along a typical flight mission. Implemented structural solutions and embedded systems were duly validated by means of ground tests carried out on a true scale prototype. Relying upon the experimental modes of the device in free-free conditions, a rational analysis was carried out in order to investigate the impacts of the morphing aileron on the aeroelastic stability of the reference aircraft. Flutter analyses were performed in compliance with EASA CS-25 airworthiness requirements and referring -at first- to nominal aileron functioning. In this way, safety values for aileron control harmonic and degree of mass-balance were defined to avoid instabilities within the flight envelope. Trade-off analyses were finally addressed to justify the robustness of the adopted massbalancing as well as the persistence of the flutter clearance in case of relevant failures/malfunctions of the morphing system components.

Spatial Distribution of Flower Color Induced by Interspecific Sexual Interaction

PubMed Central

Takahashi, Yuma; Takakura, Koh-ichi; Kawata, Masakado

2016-01-01

Understanding the mechanisms shaping the spatiotemporal distribution of species has long been a central concern of ecology and evolutionary biology. Contemporary patterns of plant assemblies suggest that sexual interactions among species, i.e., reproductive interference, lead to the exclusive distributions of closely related species that share pollinators. However, the fitness consequences and the initial ecological/evolutionary responses to reproductive interference remain unclear in nature, since reproductive isolation or allopatric distribution has already been achieved in the natural community. In Japan, three species of blue-eyed grasses (Sisyrinchium) with incomplete reproductive isolation have recently colonized and occur sympatrically. Two of them are monomorphic with white flowers, whereas the other exhibits heritable color polymorphism (white and purple morphs). Here we investigated the effects of the presence of two monomorphic species on the distribution and reproductive success of color morphs. The frequency and reproductive success of white morphs decreased in area where monomorphic species were abundant, while those of purple morphs did not. The rate of hybridization between species was higher in white morphs than in the purple ones. Resource competition and habitat preference seemed not to contribute to the spatial distribution and reproductive success of two morphs. Our results supported that color-dependent reproductive interference determines the distribution of flower color polymorphism in a habitat, implying ecological sorting promoted by pollinator-mediated reproductive interference. Our study helps us to understand the evolution and spatial structure of flower color in a community. PMID:27723785

Life-history trade-offs mediate 'personality' variation in two colour morphs of the pea aphid, Acyrthosiphon pisum.

PubMed

Schuett, Wiebke; Dall, Sasha R X; Kloesener, Michaela H; Baeumer, Jana; Beinlich, Felix; Eggers, Till

2015-01-01

Life-history trade-offs are considered a major driving force in the emergence of consistent behavioural differences (personality variation); but empirical tests are scarce. We investigated links between a personality trait (escape response), life-history and state variables (growth rate, size and age at first reproduction, age-dependent reproductive rates, lifetime reproductive success, life span) in red and green colour morphs of clonal pea aphids, Acyrthosiphon pisum. Escape response (dropping/non-dropping off a plant upon a predatory attack) was measured repeatedly to classify individuals as consistent droppers, consistent nondroppers or inconsistents. Red morphs experienced stronger trade-offs between early reproduction and life span than green morphs; and red consistent (non)droppers had highest lifetime reproductive success. Red droppers followed a risk-averse life-history strategy (high late reproduction), red nondroppers a risk-prone strategy (high early reproduction), while reproductive rates were equivalent for all green behavioural types and red inconsistents. This suggests that red morphs suffer the highest costs of dropping (they are most conspicuous to predators), which 'equivalates' fitness payoffs to both risk-takers (red non-droppers) and risk-averse red droppers. The strong trade-off also means that committing to a particular lifestyle (being consistent) maximises fitness. Our study suggests that life-history trade-offs likely mediate personality variation but effects might depend on interactions with other organismal characteristics (here: colour morph). © 2014 The Authors. Journal of Animal Ecology © 2014 British Ecological Society.

Cellular and ultrastructural characterization of the grey-morph phenotype in southern right whales (Eubalaena australis)

PubMed Central

Eroh, Guy D.; Clayton, Fred C.; Florell, Scott R.; Cassidy, Pamela B.; Chirife, Andrea; Marón, Carina F.; Valenzuela, Luciano O.; Campbell, Michael S.; Seger, Jon; Rowntree, Victoria J.; Leachman, Sancy A.

2017-01-01

Southern right whales (SRWs, Eubalena australis) are polymorphic for an X-linked pigmentation pattern known as grey morphism. Most SRWs have completely black skin with white patches on their bellies and occasionally on their backs; these patches remain white as the whale ages. Grey morphs (previously referred to as partial albinos) appear mostly white at birth, with a splattering of rounded black marks; but as the whales age, the white skin gradually changes to a brownish grey color. The cellular and developmental bases of grey morphism are not understood. Here we describe cellular and ultrastructural features of grey-morph skin in relation to that of normal, wild-type skin. Melanocytes were identified histologically and counted, and melanosomes were measured using transmission electron microscopy. Grey-morph skin had fewer melanocytes when compared to wild-type skin, suggesting reduced melanocyte survival, migration, or proliferation in these whales. Grey-morph melanocytes had smaller melanosomes relative to wild-type skin, normal transport of melanosomes to surrounding keratinocytes, and normal localization of melanin granules above the keratinocyte nuclei. These findings indicate that SRW grey-morph pigmentation patterns are caused by reduced numbers of melanocytes in the skin, as well as by reduced amounts of melanin production and/or reduced sizes of mature melanosomes. Grey morphism is distinct from piebaldism and albinism found in other species, which are genetic pigmentation conditions resulting from the local absence of melanocytes, or the inability to synthesize melanin, respectively. PMID:28170433

Conceptual design and multidisciplinary optimization of in-plane morphing wing structures

NASA Astrophysics Data System (ADS)

Inoyama, Daisaku; Sanders, Brian P.; Joo, James J.

2006-03-01

In this paper, the topology optimization methodology for the synthesis of distributed actuation system with specific applications to the morphing air vehicle is discussed. The main emphasis is placed on the topology optimization problem formulations and the development of computational modeling concepts. For demonstration purposes, the inplane morphing wing model is presented. The analysis model is developed to meet several important criteria: It must allow large rigid-body displacements, as well as variation in planform area, with minimum strain on structural members while retaining acceptable numerical stability for finite element analysis. Preliminary work has indicated that addressed modeling concept meets the criteria and may be suitable for the purpose. Topology optimization is performed on the ground structure based on this modeling concept with design variables that control the system configuration. In other words, states of each element in the model are design variables and they are to be determined through optimization process. In effect, the optimization process assigns morphing members as 'soft' elements, non-morphing load-bearing members as 'stiff' elements, and non-existent members as 'voids.' In addition, the optimization process determines the location and relative force intensities of distributed actuators, which is represented computationally as equal and opposite nodal forces with soft axial stiffness. Several different optimization problem formulations are investigated to understand their potential benefits in solution quality, as well as meaningfulness of formulation itself. Sample in-plane morphing problems are solved to demonstrate the potential capability of the methodology introduced in this paper.

Variation in the Visual Habitat May Mediate the Maintenance of Color Polymorphism in a Poeciliid Fish

PubMed Central

Hurtado-Gonzales, Jorge L.; Loew, Ellis R.; Uy, J. Albert C.

2014-01-01

The conspicuousness of animal signals is influenced by their contrast against the background. As such, signal conspicuousness will tend to vary in nature because habitats are composed of a mosaic of backgrounds. Variation in attractiveness could result in variation in conspecific mate choice and risk of predation, which, in turn, may create opportunities for balancing selection to maintain distinct polymorphisms. We quantified male coloration, the absorbance spectrum of visual pigments and the photic environment of Poecilia parae, a fish species with five distinct male color morphs: a drab (i.e., grey), a striped, and three colorful (i.e., blue, red and yellow) morphs. Then, using physiological models, we assessed how male color patterns can be perceived in their natural visual habitats by conspecific females and a common cichlid predator, Aequidens tetramerus. Our estimates of chromatic and luminance contrasts suggest that the three most colorful morphs were consistently the most conspicuous across all habitats. However, variation in the visual background resulted in variation in which morph was the most conspicuous to females at each locality. Likewise, the most colorful morphs were the most conspicuous morphs to cichlid predators. If females are able to discriminate between conspicuous prospective mates and those preferred males are also more vulnerable to predation, variable visual habitats could influence the direction and strength of natural and sexual selection, thereby allowing for the persistence of color polymorphisms in natural environments. PMID:24987856

Context-dependent crypsis: a prey's perspective of a color polymorphic predator.

PubMed

Rodríguez-Morales, D; Rico-Gray, V; García-Franco, J G; Ajuria-Ibarra, H; Hernández-Salazar, L T; Robledo-Ospina, L E; Rao, D

2018-05-12

Many animals use body coloration as a strategy to communicate with conspecifics, prey, and predators. Color is a trade-off for some species, since they should be visible to conspecifics but cryptic to predators and prey. Some flower-dwelling predators, such as crab spiders, are capable of choosing the color of flowers where they ambush flower visitors and pollinators. In order to avoid being captured, visitors evaluate flowers visually before landing. The crab spider Mecaphesa dubia is a polymorphic species (white/purple color morphs), which inhabits the flower heads of a dune plant, Palafoxia lindenii. Using full-spectrum photography of spiders and flowers, we evaluated how honeybees perceived the spiders at different distances. Using visual modeling, we obtained the chromatic and achromatic contrasts of the spiders on flower heads as perceived by honeybees. Purple morphs were found mainly on the receptacle area and white morphs were equally likely to be found in the flowers and receptacle. According to theoretical modeling, white morphs were visible to honeybees from a distance of 10 cm in receptacle area but appeared to be cryptic in the flower area. Purple morphs were cryptic on the receptacle and less so when they were on the flowers. Spiders on flower heads are predicted to be more easily detected by honeybees using chromatic contrast. Our study shows that the conspicuousness of flower dwelling spiders to honeybees depends on the color morph, the distance of observation, and the position of spider on the flower head.

Cellular and ultrastructural characterization of the grey-morph phenotype in southern right whales (Eubalaena australis).

PubMed

Eroh, Guy D; Clayton, Fred C; Florell, Scott R; Cassidy, Pamela B; Chirife, Andrea; Marón, Carina F; Valenzuela, Luciano O; Campbell, Michael S; Seger, Jon; Rowntree, Victoria J; Leachman, Sancy A

2017-01-01

Southern right whales (SRWs, Eubalena australis) are polymorphic for an X-linked pigmentation pattern known as grey morphism. Most SRWs have completely black skin with white patches on their bellies and occasionally on their backs; these patches remain white as the whale ages. Grey morphs (previously referred to as partial albinos) appear mostly white at birth, with a splattering of rounded black marks; but as the whales age, the white skin gradually changes to a brownish grey color. The cellular and developmental bases of grey morphism are not understood. Here we describe cellular and ultrastructural features of grey-morph skin in relation to that of normal, wild-type skin. Melanocytes were identified histologically and counted, and melanosomes were measured using transmission electron microscopy. Grey-morph skin had fewer melanocytes when compared to wild-type skin, suggesting reduced melanocyte survival, migration, or proliferation in these whales. Grey-morph melanocytes had smaller melanosomes relative to wild-type skin, normal transport of melanosomes to surrounding keratinocytes, and normal localization of melanin granules above the keratinocyte nuclei. These findings indicate that SRW grey-morph pigmentation patterns are caused by reduced numbers of melanocytes in the skin, as well as by reduced amounts of melanin production and/or reduced sizes of mature melanosomes. Grey morphism is distinct from piebaldism and albinism found in other species, which are genetic pigmentation conditions resulting from the local absence of melanocytes, or the inability to synthesize melanin, respectively.

Context-dependent crypsis: a prey's perspective of a color polymorphic predator

NASA Astrophysics Data System (ADS)

Rodríguez-Morales, D.; Rico-Gray, V.; García-Franco, J. G.; Ajuria-Ibarra, H.; Hernández-Salazar, L. T.; Robledo-Ospina, L. E.; Rao, D.

2018-06-01

Many animals use body coloration as a strategy to communicate with conspecifics, prey, and predators. Color is a trade-off for some species, since they should be visible to conspecifics but cryptic to predators and prey. Some flower-dwelling predators, such as crab spiders, are capable of choosing the color of flowers where they ambush flower visitors and pollinators. In order to avoid being captured, visitors evaluate flowers visually before landing. The crab spider Mecaphesa dubia is a polymorphic species (white/purple color morphs), which inhabits the flower heads of a dune plant, Palafoxia lindenii. Using full-spectrum photography of spiders and flowers, we evaluated how honeybees perceived the spiders at different distances. Using visual modeling, we obtained the chromatic and achromatic contrasts of the spiders on flower heads as perceived by honeybees. Purple morphs were found mainly on the receptacle area and white morphs were equally likely to be found in the flowers and receptacle. According to theoretical modeling, white morphs were visible to honeybees from a distance of 10 cm in receptacle area but appeared to be cryptic in the flower area. Purple morphs were cryptic on the receptacle and less so when they were on the flowers. Spiders on flower heads are predicted to be more easily detected by honeybees using chromatic contrast. Our study shows that the conspicuousness of flower dwelling spiders to honeybees depends on the color morph, the distance of observation, and the position of spider on the flower head.

Component Release and Mechanical Properties of Endodontic Sealers following Incorporation of Antimicrobial Agents.

PubMed

Gjorgievska, Elizabeta S; Nicholson, John W; Coleman, Nichola J; Booth, Samantha; Dimkov, Aleksandar; Hurt, Andrew

2017-01-01

Root canal sealers with antimicrobial activity are highly beneficial; therefore, their antimicrobial properties could be improved by incorporation of antimicrobial agents. In the present study, the release of the quaternary ammonium compounds from endodontic sealers admixed with either benzalkonium chloride (BC) or cetylpyridinium chloride (CPC) at loadings of 2% wt was monitored. The effect of these additives on the compressive strengths and their release from the sealers was determined after 1 and 4 weeks. All of the materials studied were found to be capable of releasing antimicrobial additive in useful quantities. The release of CPC occurred to a statistically significant greater extent than BC for all materials. The addition of both BC and CPC generally decreased the compressive strength of all the endodontic sealers, with the exception of CPC in AH Plus, where the compressive strength was significantly increased. This suggests that, for these endodontic sealers, the antimicrobial additives alter the setting chemistry. AH Plus is an epoxy-based material cured with an amine, and in this case the increase in compressive strength with CPC is attributed to an enhanced cure reaction with this system. In all other cases, the additive inhibited the cure reaction to a greater or lesser extent.

Formulation and characterization of cetylpyridinium chloride bioadhesive tablets.

PubMed

Akbari, Jafar; Saeedi, Majid; Morteza-Semnani, Katayoun; Kelidari, Hamidreza; Lashkari, Maryam

2014-12-01

Bioadhesive polymers play an important role in biomedical and drug delivery applications. The aim of this study is to develop a sustained- release tablet for local application of Cetylpyridinium Chloride (CPC). This delivery system would supply the drug at an effective level for a long period of time, and thereby overcome the problem of the short retention time of CPC and could be used for buccal delivery as a topical anti-infective agent. CPC bioadhesive tablets were directly prepared using 7 mm flat-faced punches on a hydraulic press. The materials for each tablet were weighted, introduced into the die and compacted at constant compression pressure. The dissolution tests were performed to the rotation paddle method and the bioadhesive strength of the tablets were measured. The results showed that as the concentration of polymer increased, the drug release rate was decreased. Also the type and ratio of polymers altered the release kinetic of Cetylpyridinium Chloride from investigated tablets. The bioadhesion strength increased with increasing the concentration of polymer and maximum bioadhesion strength was observed with HPMC K100M. The selected formulation of CPC bioadhesive tablet can be used as a suitable preparation for continuous release of CPC with appropriate bioadhesion strength.

Preparation and bioavailability of calcium-chelating peptide complex from tilapia skin hydrolysates.

PubMed

Chen, Jun; Qiu, Xujian; Hao, Gengxin; Zhang, Meng; Weng, Wuyin

2017-11-01

With the continuous improvement in material life, the generation of fish by-products and the market demand for calcium supplements have been increasing in China. Therefore a calcium-chelating peptide complex (CPC) from tilapia skins was prepared and its effect on calcium (Ca)-deficient mice was investigated. The molecular weight distribution of CPC mainly ranged from 2000 to 180 Da, and its contents of complete amino acids and free amino acids were 85.30 and 8.67% (w/w) respectively. Scanning electron microscopy images and Fourier transform infrared data revealed that Ca crystals were bound with gelatin hydrolysates via interaction between Ca ions and NH/CN groups. When Ca-deficient mice were fed CPC and CaCO 3 respectively for 4 weeks, no significant differences in serum biochemistry or bone mineral density were found. However, the length, weight, Ca content and hydroxyproline content of the femur, Ca absorption and body weight gain of mice fed CPC were significantly higher than those of mice fed CaCO 3 . It is concluded that the prepared CPC could promote bone formation via better bioavailability of Ca and an increase in bone collagen. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Engineering strategies for simultaneous enhancement of C-phycocyanin production and CO2 fixation with Spirulina platensis.

PubMed

Chen, Chun-Yen; Kao, Pei-Chun; Tsai, Chia-Jung; Lee, Duu-Jong; Chang, Jo-Shu

2013-10-01

Spirulina platensis produces nutraceutical product C-phycocyanin (C-PC) and simultaneously mitigates CO2 emissions during its growth. Using a designed flat-type photobioreactor, the S. platensis biomass production was markedly enhanced, leading to a CO2 removal rate and a biomass concentration of 0.23 g/L/d and 2.25 g/L, respectively. The cell growth, CO2 fixation rate and C-PC production of S. platensis were investigated when it was cultivated under different irradiation conditions. As the light intensity increased from 100 to 700 μmol/m(2)/s, the overall biomass productivity, CO2 consumption rate and maximal C-PC productivity increased significantly to 0.74, 1.53 and 0.11 g/L/d, respectively. After determining the suitable light intensity, the nitrogen concentration was also adjusted to further enhance the performance of CO2 fixation and C-PC production. The results show that with an optimal nitrogen concentration of 0.045 M, the CO2 consumption rate and maximal C-PC productivity were further increased to 1.58 and 0.13 g/L/d, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Changes in predator community structure shifts the efficacy of two warning signals in Arctiid moths.

PubMed

Nokelainen, Ossi; Valkonen, Janne; Lindstedt, Carita; Mappes, Johanna

2014-05-01

Polymorphism in warning coloration is puzzling because positive frequency-dependent selection by predators is expected to promote monomorphic warning signals in defended prey. We studied predation on the warning-coloured wood tiger moth (Parasemia plantaginis) by using artificial prey resembling white and yellow male colour morphs in five separate populations with different naturally occurring morph frequencies. We tested whether predation favours one of the colour morphs over the other and whether that is influenced either by local, natural colour morph frequencies or predator community composition. We found that yellow specimens were attacked less than white ones regardless of the local frequency of the morphs indicating frequency-independent selection, but predation did depend on predator community composition: yellows suffered less attacks when Paridae were abundant, whereas whites suffered less attacks when Prunellidae were abundant. Our results suggest that spatial heterogeneity in predator community composition can generate a geographical mosaic of selection facilitating the evolution of polymorphic warning signals. This is the first time this mechanism gains experimental support. Altogether, this study sheds light on the evolution of adaptive coloration in heterogeneous environments. © 2013 The Authors. Journal of Animal Ecology © 2013 British Ecological Society.

Dynamics of colour polymorphism in a changing environment: fire melanism and then what?

PubMed

Karlsson, Magnus; Caesar, Sofia; Ahnesjö, Jonas; Forsman, Anders

2008-01-01

Studies of whether disturbance events are associated with the changing genetic compositions of natural populations may provide insights into the importance of local selection events in maintaining diversity, and might inform plans for the conservation and protection of that diversity. We examined the dynamics of a colour pattern polymorphism in a natural population of pygmy grasshoppers Tetrix subulata (Orthoptera: Tetrigidae) inhabiting a previously burnt clear-cut area. Data on morph frequencies for wild-caught and captive-reared individuals indicated that the initial dominance of black phenotypes following the fire event was followed by an increased diversity of the polymorphism. This was manifested as the appearance of a novel morph, a decreased incidence of the black morph, and a more even distribution of individuals across alternative morphs following the recurrence of vegetation. We also found that the colour patterns of captive-reared individuals resembled those of their parents and that the degree of within-clutch diversity increased between generations. Our comparisons of morph frequencies across generations and between environments within generations point to a genetic determination of colour pattern, and indicate that the polymorphism is influenced more strongly by selection than by plasticity or migration.

Osmotic fragility changes in preserved blood: measurements by coil planet centrifuge and parpart methods.

PubMed

Sasakawa, S; Tokunaga, E; Hasegawa, G; Nakagawa, S

1977-09-01

The coil planet centrifuge (CPC) can be used to measure the osmotic fragility of erythrocytes. Fragility measured by this method alters when different salts are used. The CPC and Parpart methods were used to measure the changes during storage in red cell osmotic fragility in ACD or CPD blood with or without adenine. More marked changes were detected by the CPC method, especially in old cells. The changes of fragility of erythrocytes during storage seem to occur mainly in old cells. Adenine is effective in preventing such changes.

F15B-Quiet Spike Aeroservoelastic Flight Test Data Analysis

NASA Technical Reports Server (NTRS)

Brenner, Martin J.

2007-01-01

Airframe structural morphing technologies designed to mitigate sonic boom strength are being developed by Gulfstream Aerospace Corporation (GAC). Among these technologies is a concept in which an aircraft's frontend would be extended prior to supersonic acceleration. This morphing would effectively lengthen the vehicle, reducing peak sonic boom amplitude, but is also expected to partition the otherwise strong bow shock into a series of reduced-strength, non-coalescing shocklets. This combination of boom shaping techniques is predicted to transform the classic, high-impulse N-wave pattern typically generated by an aircraft traveling at supersonic speed into a signature more closely resembling a sinusoidal wave with a greatly reduced perceived loudness. 'QuietSpike' is GAC's nomenclature for its recently patented front-end vehicle morphing arrangement. The ability of Quiet Spike to effectively shape a vehicle's far- field sonic boom signature is highly dependent on the area distribution characteristics of the aircraft. The full aeroacoustic benefits of front-end morphing at farfield are only possible when the QuietSpike article and vehicle configuration are designed in consideration of each other. Adding QuietSpike technology to the airframe of an existing, non-boom-optimized supersonic vehicle is unlikely to result in an improved far-field signature due to the generally over-powering influence of wing- and inlet-generated shocks. Therefore, it is generally recognized within NASA and the industry that a clean-sheet vehicle design is required to demonstrate the theoretically predicted far-field aeroacoustic benefits of QuietSpike type morphing and other boom- mitigating concepts. NASA's Aeronautics Research Mission Directorate (ARMD) Supersonics Division has placed increased priority on near-term development and flight-testing of such a vehicle. To help achieve this objective, static and dynamic aerostructural proof-of-concept testing was considered a prudent step prior to a clean-sheet effort in order to reduce risk associated with a follow-on test program. Following a survey of potential test platforms, NASA Dryden's F-15B was selected as the target test vehicle primarily because of its unique ability to carry a largescale test apparatus to relevant supersonic flight speeds, so called the F15 -QS. The QuietSpike test article was constructed primarily of composite materials and attached to the forward fuselage of the F-1 5B bulkhead (see Figures 1,2). The QuietSpike test article replaces the current flight test noseboom and radome assembly. Power is supplied to the Quiet Spike motor assembly in order to extend and retract the Spike, and the Quiet Spike test article was appropriately instrumented with accelerometers, strain gages, pressure transducers, and thermocouples.

Nucleostemin Rejuvenates Cardiac Progenitor Cells and Antagonizes Myocardial Aging

PubMed Central

Hariharan, Nirmala; Quijada, Pearl; Mohsin, Sadia; Joyo, Anya; Samse, Kaitlen; Monsanto, Megan; De La Torre, Andrea; Avitabile, Daniele; Ormachea, Lucia; McGregor, Michael J.; Tsai, Emily J; Sussman, Mark A.

2015-01-01

BACKGROUND Functional decline in stem cell-mediated regeneration contributes to aging associated with cellular senescence in c-kit+ cardiac progenitor cells (CPCs). Clinical implementation of CPC-based therapy with elderly patients would benefit tremendously from understanding molecular characteristics of senescence to antagonize aging. Nucleostemin (NS) is a nucleolar protein regulating stem cell proliferation and pluripotency. OBJECTIVES The goal is to demonstrate that NS preserves characteristics associated with “stemness” in CPCs and antagonizes myocardial senescence and aging. METHODS CPCs isolated from human fetal (FhCPC) and adult failing (AhCPC) hearts, as well as young (YCPC) and old mice (OCPC), were studied for senescence characteristics and NS expression. Heterozygous knockout mice with one functional allele of NS (NS+/−) were used to demonstrate that NS preserves myocardial structure and function and slows characteristics of aging. RESULTS NS expression is decreased in AhCPCs relative to FhCPC, correlating with lowered proliferation potential and shortened telomere length. AhCPC characteristics resemble OCPCs, which have a phenotype induced by NS silencing, resulting in cell flattening, senescence, multinucleated cells, decreased S phase progression, diminished expression of stemness markers and up-regulation of p53 and p16. CPC senescence resulting from NS loss is partially p53 dependent and is rescued by concurrent silencing of p53. Mechanistically, NS induction correlates with Pim-1 kinase-mediated stabilization of c-Myc. Engineering OCPCs and AhCPCs to overexpress NS decreases senescent and multinucleated cells, restores morphology, and antagonizes senescence, thereby preserving phenotypic properties of “stemness.” Early cardiac aging with decline in cardiac function, increase in senescence markers p53 and p16, telomere attrition, and accompanied CPC exhaustion is evident in NS+/− mice. CONCLUSIONS Youthful properties and antagonism of senescence in CPCs and the myocardium is consistent with a role for NS downstream from Pim-1 signaling that enhances cardiac regeneration. PMID:25593054

A novel combined solar pasteurizer/TiO2 continuous-flow reactor for decontamination and disinfection of drinking water.

PubMed

Monteagudo, José María; Durán, Antonio; Martín, Israel San; Acevedo, Alba María

2017-02-01

A new combined solar plant including an annular continuous-flow compound parabolic collector (CPC) reactor and a pasteurization system was designed, built, and tested for simultaneous drinking water disinfection and chemical decontamination. The plant did not use pumps and had no electricity costs. First, water continuously flowed through the CPC reactor and then entered the pasteurizer. The temperature and water flow from the plant effluent were controlled by a thermostatic valve located at the pasteurizer outlet that opened at 80 °C. The pasteurization process was simulated by studying the effect of heat treatment on the death kinetic parameters (D and z values) of Escherichia coli K12 (CECT 4624). 99.1% bacteria photo-inactivation was reached in the TiO 2 -CPC system (0.60 mg cm -2 TiO 2 ), and chemical decontamination in terms of antipyrine degradation increased with increasing residence time in the TiO 2 -CPC system, reaching 70% degradation. The generation of hydroxyl radicals (between 100 and 400 nmol L -1 ) was a key factor in the CPC system efficiency. Total thermal bacteria inactivation was attained after pasteurization in all cases. Chemical degradation and bacterial photo-inactivation in the TiO 2 -CPC system were improved with the addition of 150 mg L -1 of H 2 O 2 , which generated approximately 2000-2300 nmol L -1 of HO ● radicals. Finally, chemical degradation and bacterial photo-inactivation kinetic modelling in the annular CPC photoreactor were evaluated. The effect of the superficial liquid velocity on the overall rate constant was also studied. Both antipyrine degradation and E. coli photo-inactivation were found to be controlled by the catalyst surface reaction rate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ion Movements in Cell Injury

PubMed Central

Saladino, Andrew J.; Hawkins, Hal K.; Trump, Benjamin F.

1971-01-01

The effects of a cationic detergent, cetyl pyridinium chloride (CPC), on toad bladder epithelium were studied by means of electrophysiologic and sodium-flux measurements, chemical analysis, time-lapse phase-contrast cinemicrography and electron microscopy. At 10-5 M, CPC caused a rapid loss of net sodium transport as reflected by the short-circuit current (SCC) but except for striking prominence of the glycocalyx, this dose caused no ultrastructural changes for at least 18 hours. Only a moderate decrease in resistance and increase in passive sodium flux were noted. At 10-4 M, CPC caused a transient 1 to 2-minute increase in the bladder's rate of oxygen consumption followed by a decrease, and a rapid decline in SCC, followed a few minute later by a decrease in resistance accompanied by a greatly increased passive leak to sodium. A sequence of ultrastructural changes typical of other forms of lethal cell injury progressed to extensive cellular disruption by 1 hour after treatment with 10-4 M CPC. In addition, unusual surface membrane changes were observed, consisting of extensive formation of vesicles and myelin figures at the cell surface. A significant fraction of the bladder's cholesterol content appeared in the incubation medium after 10-4 M CPC treatment. With 10-3 M CPC, a similar pattern of cellular degeneration proceeded much more rapidly, and in addition, the cellular remains reorganized into complex lamellar arrays resembling phospholipid crystalloids. The results are interpreted as indicating that in addition to inhibiting net sodium transport, CPC lethally injures cells by interfering with the function of the surface membrane as a permeability barrier, and in addition, leads to a drastic structural reorganization of membrane constituents. ImagesFig 9Fig 10Fig 1Fig 2Fig 11Fig 12Fig 13Fig 5Fig 6Fig 7Fig 8Fig 14Fig 15Fig 16Fig 3Fig 4 PMID:4946878

The Ins and Outs of Aurora B Inner Centromere Localization

PubMed Central

Hindriksen, Sanne; Lens, Susanne M. A.; Hadders, Michael A.

2017-01-01

Error-free chromosome segregation is essential for the maintenance of genomic integrity during cell division. Aurora B, the enzymatic subunit of the Chromosomal Passenger Complex (CPC), plays a crucial role in this process. In early mitosis Aurora B localizes predominantly to the inner centromere, a specialized region of chromatin that lies at the crossroads between the inter-kinetochore and inter-sister chromatid axes. Two evolutionarily conserved histone kinases, Haspin and Bub1, control the positioning of the CPC at the inner centromere and this location is thought to be crucial for the CPC to function. However, recent studies sketch a subtler picture, in which not all functions of the CPC require strict confinement to the inner centromere. In this review we discuss the molecular pathways that direct Aurora B to the inner centromere and deliberate if and why this specific localization is important for Aurora B function. PMID:29312936

The effect of a mouthrinse containing chlorine dioxide in the clinical reduction of volatile sulfur compounds.

PubMed

Soares, Leo Guimaraes; Guaitolini, Roberto Luiz; Weyne, Sergio de Carvalho; Falabella, Marcio Eduardo Vieira; Tinoco, Eduardo Muniz Barretto; da Silva, Denise Gomes

2013-07-01

This study sought to evaluate the clinical effect of a mouthrinse containing 0.3% chlorine dioxide (ClO2) in reducing oral volatile sulfur compounds (VSC). Halitosis was induced by L-cysteine in 11 volunteers, and 4 solutions were compared: a test solution containing 0.3% ClO2, 0.07% cetylpyridinium chloride (CPC), and 0.05% sodium fluoride; a placebo; a solution containing 0.05% CPC; and a control solution of 0.2% chlorhexidine gluconate (CHX). VSC levels were assessed using a Halimeter, and 6 measurements were made from baseline to 3 hours postrinse. The VSC reduction rate of the test mouthrinse was superior to the placebo and the CPC solution. There was no difference between the test solution and the CHX solution in VSC reduction rates immediately postrinse, or at 2 and 3 hours postrinse; both solutions were statistically superior to the placebo and the CPC solution.

RCC1 regulates inner centromeric composition in a Ran-independent fashion.

PubMed

Zhang, Michael Shaofei; Furuta, Maiko; Arnaoutov, Alexei; Dasso, Mary

2018-01-01

RCC1 associates to chromatin dynamically within mitosis and catalyzes Ran-GTP production. Exogenous RCC1 disrupts kinetochore structure in Xenopus egg extracts (XEEs), but the molecular basis of this disruption remains unknown. We have investigated this question, utilizing replicated chromosomes that possess paired sister kinetochores. We find that exogenous RCC1 evicts a specific subset of inner KT proteins including Shugoshin-1 (Sgo1) and the chromosome passenger complex (CPC). We generated RCC1 mutants that separate its enzymatic activity and chromatin binding. Strikingly, Sgo1 and CPC eviction depended only on RCC1's chromatin affinity but not its capacity to produce Ran-GTP. RCC1 similarly released Sgo1 and CPC from synthetic kinetochores assembled on CENP-A nucleosome arrays. Together, our findings indicate RCC1 regulates kinetochores at the metaphase-anaphase transition through Ran-GTP-independent displacement of Sgo1 and CPC.

Protective effects of C-phycocyanin on alcohol-induced acute liver injury in mice

NASA Astrophysics Data System (ADS)

Xia, Dong; Liu, Bing; Luan, Xiying; Sun, Junyan; Liu, Nana; Qin, Song; Du, Zhenning

2016-03-01

Excessive alcohol consumption leads to liver disease. Extensive evidence suggests that C-phycocyanin (C-PC), a chromophore phycocyanobilin derived from Spirulina platensis, exerts protective effects against chemical-induced organ damage. In this study, we investigated whether C-PC could protect against ethanol-induced acute liver injury. Serum alanine aminotransferase (ALT), aspartate aminotransferase (AST), triglyceride (TG), total cholesterol (CHOL), low-density lipoprotein (LDL), liver homogenate malondialdehyde (MDA), superoxide dismutase (SOD) content were measured, and pathological examination of liver sections were examined. C-PC showed obvious inhibitory effects on serum ALT, AST, TG, CHOL, LDL and MDA, and SOD content significantly increased in the liver. The structure of hepatic lobules was clear, liver sinus returned to normal, and liver cell cords were arranged in neat rows. Cloudiness, swelling, inflammatory cell infiltration and spotty necrosis of liver cells were significantly reduced. Therefore, C-PC can significantly protect against ethanol-induced acute liver injury.

[Studies on the physical dependence liability of chlorphenesin carbamate (author's transl)].

PubMed

Sasajima, M; Tarumoto, Y; Aihara, H; Tanaka, Y; Saito, S

1977-05-01

Physical dependence liability of chlorphenesin carbamate (CPC) was studied in parallel with phenobarbital-Na (PB). Beagle dogs were used and the overall duration of the experiment was 85 days, i.e. the first dosing period was 42 dyas (6 weeks) in which drugs were repeatedly administered orally once daily, followed by a withdrawal period (7 days), the second dosing period was continued from the 50th-78th day in which the form and schedule of drug administration was as in the first dosing period. The last 79th to 85th days were used for substitution experiments. In both dosing periods, PB but not CPC showed signs of tolerance formation. Severe withdrawal syndrome was observed in PB administered dogs whereas there were no changes of behavior observed in CPC-dogs by withdrawal and substitution procedures, respectively. CPC apparently does not have a physical dependence liability.

Development of emotional facial recognition in late childhood and adolescence.

PubMed

Thomas, Laura A; De Bellis, Michael D; Graham, Reiko; LaBar, Kevin S

2007-09-01

The ability to interpret emotions in facial expressions is crucial for social functioning across the lifespan. Facial expression recognition develops rapidly during infancy and improves with age during the preschool years. However, the developmental trajectory from late childhood to adulthood is less clear. We tested older children, adolescents and adults on a two-alternative forced-choice discrimination task using morphed faces that varied in emotional content. Actors appeared to pose expressions that changed incrementally along three progressions: neutral-to-fear, neutral-to-anger, and fear-to-anger. Across all three morph types, adults displayed more sensitivity to subtle changes in emotional expression than children and adolescents. Fear morphs and fear-to-anger blends showed a linear developmental trajectory, whereas anger morphs showed a quadratic trend, increasing sharply from adolescents to adults. The results provide evidence for late developmental changes in emotional expression recognition with some specificity in the time course for distinct emotions.

A supergene determines highly divergent male reproductive morphs in the ruff

PubMed Central

dos Remedios, Natalie; Farrell, Lindsay L.; McRae, Susan B.; Morgan, Tawna C.; Karlionova, Natalia; Pinchuk, Pavel; Verkuil, Yvonne I.; Kitaysky, Alexander S.; Wingfield, John C.; Piersma, Theunis; Zeng, Kai; Slate, Jon; Blaxter, Mark; Lank, David B.; Burke, Terry

2015-01-01

Three strikingly different alternative male mating morphs (aggressive “Independents”, semi-cooperative “Satellites” and female mimic “Faeders”) coexist as a balanced polymorphism in the ruff, Philomachus pugnax, a lek-breeding wading bird1,2,3. Major differences in body size, ornamentation, and aggressive and mating behaviour are inherited as an autosomal polymorphism4,5. We show that development into Satellites and Faeders is determined by a supergene6,7,8 consisting of divergent alternative, dominant, non-recombining haplotypes of an inversion on chromosome 11, which contains 125 predicted genes. Independents are homozygous for the ancestral sequence. One breakpoint of the inversion disrupts the essential Centromere protein N (CENP-N) gene, and pedigree analysis confirms lethality of inversion homozygotes. We describe novel behavioural, testes size, and steroid metabolic differences among morphs, and identify polymorphic genes within the inversion that are likely to contribute to the differences among morphs in reproductive traits. PMID:26569125

Development of SMA Actuated Morphing Airfoil for Wind Turbine Load Alleviation

NASA Astrophysics Data System (ADS)

Karakalas, A.; Machairas, T.; Solomou, A.; Riziotis, V.; Saravanos, D.

Wind turbine rotor upscaling has entered a range of rotor diameters where the blade structure cannot sustain the increased aerodynamic loads without novel load alleviation concepts. Research on load alleviation using morphing blade sections is presented. Antagonistic shape memory alloy (SMA) actuators are implemented to deflect the section trailing edge (TE) to target shapes and target time-series relating TE movement with changes in lift coefficient. Challenges encountered by the complex thermomechanical response of morphing section and the enhancement of SMA transient response to achieve frequencies meaningful for aerodynamic load alleviation are addressed. Using a recently developed finite element for SMA actuators [1], actuator configurations are considered for fast cooling and heating cycles. Numerical results quantify the attained ranges of TE angle movement, the moving time period and the developed stresses. Estimations of the attained variations of lift coefficient vs. time are also presented to assess the performance of the morphing section.

Four heads are better than one: combining face composites yields improvements in face likeness.

PubMed

Bruce, Vicki; Ness, Hayley; Hancock, Peter J B; Newman, Craig; Rarity, Jenny

2002-10-01

Four participants constructed face composites, of familiar and unfamiliar targets, using Pro-Fit, with reference images present or from memory. The "mean" of all 4 composites, created by morphing (4-morph) was rated as a better likeness than individual composites on average and was as good as the best individual likeness. When participants attempted to identify targets from line-ups, 4-morphs again performed as well as the best individual composite. In a second experiment, participants familiar with target women attempted to identify composites, and the trend showed better recognition from multiple composites, whether combined or shown together. In a line-up task with unfamiliar participants, 4-morphs produced most correct choices and fewest false positives from target-absent or target-present arrays. These results have practical implications for the way evidence from different witnesses is used in police investigations.

Shape memory alloy-actuated bistable composites for morphing structures

NASA Astrophysics Data System (ADS)

Chillara, Venkata Siva C.; Dapino, Marcelo J.

2018-03-01

Laminated composites with orthogonally-applied mechanical prestress have been shown to exhibit two stable shapes where each shape is influenced by only one prestrained lamina. The application of mechanical prestress is associated with an irreversible non-zero stress state; when combined with smart materials with controllable stress-states, this results in multifunctionality in morphing composites. This study presents an experimental characterization of the shape transition or snap-through in mechanically-prestressed bistable laminates. Measurements, conducted using tensile testing and 3D motion capture, show that snap-through in these laminates is a multi-stage phenomenon. An active bistable morphing composite is demonstrated using NiTi shape memory wire actuators in push-pull configuration; activation of one wire resets the second wire as the composite morphs. The set of shape memory actuators not only actuate the composite in both directions, but also act as dampers that enable vibration-free shape transition.

Mechanical vibrations from tadpoles' flapping tails transform salamander's carnivorous morphology.

PubMed

Michimae, Hirofumi; Nishimura, Kinya; Wakahara, Masami

2005-03-22

Some prey or predator organisms exhibit striking rapid morphological plastic changes with distinct morphology under the condition of predator or prey presence. Remote chemicals propagating from the inducing agents are the prevalent induction cues for most examples of induction of distinct morphs. Sonic and visual cues, as well as chemical cues, are known as triggers for induction of behavioural plasticity. Here we show that hydraulic vibration originating from flapping tails of anuran tadpoles is a key cue in relation to induction of a distinct carnivorous morphology, a broad-headed morph, in larval salamander Hynobius retardatus, which is able to efficiently capture and handle prey. This result was further supported by the fact that simple mechanical vibrations of tail-like vinyl fins were able to induce the morph without any biological cues. Induction of the morph triggered by hydraulic vibration provides a novel concept for understanding the proximate mechanisms of induction of morphological changes.

NASA's Morphing Project Research Summaries in Fiscal Year 2002

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria R.; Waszak, Martin R.

2005-01-01

The Morphing Project at the National Aeronautics and Space Agency s (NASA) Langley Research Center (LaRC) is part of the Breakthrough Vehicle Technologies Project, Vehicle Systems Program that conducts fundamental research on advanced technologies for future flight vehicles. The objectives of the Morphing Project are to develop and assess the advanced technologies and integrated component concepts to enable efficient, multi-point adaptability of flight vehicles; primarily through the application of adaptive structures and adaptive flow control to substantially alter vehicle performance characteristics. This document is a compilation of research summaries and other information on the project for fiscal year 2002. The focus is to provide a brief overview of the project content, technical results and lessons learned. At the time of publication, the Vehicle Systems Program (which includes the Morphing Project) is undergoing a program re-planning and reorganization. Accordingly, the programmatic descriptions of this document pertain only to the program as of fiscal year 2002.

What is Falco Altaicus Menzbier?

USGS Publications Warehouse

Ellis, D.H.

1995-01-01

The systematics of the Altay falcon (Falco altaicus/lorenzi) remains enigmatic. First reported in 1811, it has been treated as a gyrfalcon (F. rusticolus), a saker (F. cherrug), and two separate species (F. lorenzi and F. altaicus). Of 53 'altaicus' specimens examined, at least two are misidentified gyrfalcons, many are typical sakers, but 34 (the core group) are considered to be the true Altay falcon type. Adults have red, brown, and gray color morphs. The red (backed) morph closely resembles some eastern sakers; the chocolate and gray morphs resemble respective gyrfalcon morphs. While the true affinities of the Altay falcon will be resolved by molecular genetics, the ecological, geographical, and morphological information suggest that the core group represents a gyrfalcon-saker cross that is being swamped through back crosses with the saker. The breeding range of the core group (i.e., the Altay and Sayan Mountains) is much smaller than previously reported.

Shape Optimization and Modular Discretization for the Development of a Morphing Wingtip

NASA Astrophysics Data System (ADS)

Morley, Joshua

Better knowledge in the areas of aerodynamics and optimization has allowed designers to develop efficient wingtip structures in recent years. However, the requirements faced by wingtip devices can be considerably different amongst an aircraft's flight regimes. Traditional static wingtip devices are then a compromise between conflicting requirements, resulting in less than optimal performance within each regime. Alternatively, a morphing wingtip can reconfigure leading to improved performance over a range of dissimilar flight conditions. Developed within this thesis, is a modular morphing wingtip concept that centers on the use of variable geometry truss mechanisms to permit morphing. A conceptual design framework is established to aid in the development of the concept. The framework uses a metaheuristic optimization procedure to determine optimal continuous wingtip configurations. The configurations are then discretized for the modular concept. The functionality of the framework is demonstrated through a design study on a hypothetical wing/winglet within the thesis.

Diazotrophic diversity in the Caribbean coral, Montastraea cavernosa.

PubMed

Olson, Nathan D; Lesser, Michael P

2013-12-01

Previous research on the Caribbean coral Montastraea cavernosa reported the presence of cyanobacterial endosymbionts and nitrogen fixation in orange, but not brown, colonies. We compared the diversity of nifH gene sequences between these two color morphs at three locations in the Caribbean and found that the nifH sequences recovered from M. cavernosa were consistent with previous studies on corals where members of both the α-proteobacteria and cyanobacteria were recovered. A number of nifH operational taxonomic units (OTUs) were significantly more abundant in the orange compared to the brown morphs, and one specific OTU (OTU 17), a cyanobacterial nifH sequence similar to others from corals and sponges and related to the cyanobacterial genus Cyanothece, was found in all orange morphs of M. cavernosa at all locations. The nifH diversity reported here, from a community perspective, was not significantly different between orange and brown morphs of M. cavernosa.

The efficacy of two oral hygiene regimens in reducing oral malodour: a randomised clinical trial.

PubMed

Feres, Magda; Figueiredo, Luciene Cristina; Faveri, Marcelo; Guerra, Marcelo C; Mateo, Luis R; Stewart, Bernal; Williams, Malcolm; Panagakos, Foti

2015-12-01

This study compared the efficacy of two oral hygiene regimens in reducing oral malodour and the proportions of bacterial species involved in the production of volatile sulphur compounds. Seventy subjects who participated in a halitosis-induction phase and achieved an organoleptic score of ≥ 3.0 [time point 0 (T0)] randomised into two groups: brushing with regular fluoride toothpaste alone (control group) or brushing with regular fluoride toothpaste followed by rinsing with a 0.075% cetylpyridinium chloride (CPC) mouthwash (CPC group). Subjects followed their assigned oral hygiene regimen for 21 days. Then, they underwent an organoleptic examination and measurement of volatile sulphur compounds (VSCs) using a portable gas chromatograph, 12 hours after their last oral hygiene procedure (T1) and 4 hours after an on-site oral hygiene (T2). Microbiological samples (supragingival biofilm, tongue coating and saliva) were analysed using checkerboard DNA-DNA hybridisation. Both therapies statistically significantly improved the organoleptic scores (P < 0.05), but the VSC levels and/or concentrations were reduced only in the CPC group (P < 0.05). In subjects rinsing with CPC, oral malodour scores were reduced by 49% at the 4-hour assessment (T2) compared with those not rinsing (P < 0.05). Red-complex pathogens were reduced more effectively in the CPC group than in the control group. Brushing followed by rinsing with a 0.075% CPC mouthwash provided statistically significantly greater reductions in oral malodour, measured organoleptically and instrumentally, and in the proportions of red-complex species when compared with brushing alone. © 2015 FDI World Dental Federation.

Boosting the pentose phosphate pathway restores cardiac progenitor cell availability in diabetes.

PubMed

Katare, Rajesh; Oikawa, Atsuhiko; Cesselli, Daniela; Beltrami, Antonio P; Avolio, Elisa; Muthukrishnan, Deepti; Munasinghe, Pujika Emani; Angelini, Gianni; Emanueli, Costanza; Madeddu, Paolo

2013-01-01

Diabetes impinges upon mechanisms of cardiovascular repair. However, the biochemical adaptation of cardiac stem cells to sustained hyperglycaemia remains largely unknown. Here, we investigate the molecular targets of high glucose-induced damage in cardiac progenitor cells (CPCs) from murine and human hearts and attempt safeguarding CPC viability and function through reactivation of the pentose phosphate pathway. Type-1 diabetes was induced by streptozotocin. CPC abundance was determined by flow cytometry. Proliferating CPCs were identified in situ by immunostaining for the proliferation marker Ki67. Diabetic hearts showed marked reduction in CPC abundance and proliferation when compared with controls. Moreover, Sca-1(pos) CPCs isolated from hearts of diabetic mice displayed reduced activity of key enzymes of the pentose phosphate pathway, glucose-6-phosphate dehydrogenase (G6PD), and transketolase, increased levels of superoxide and advanced glucose end-products (AGE), and inhibition of the Akt/Pim-1/Bcl-2 signalling pathway. Similarly, culture of murine CPCs or human CD105(pos) progenitor cells in high glucose inhibits the pentose phosphate and pro-survival signalling pathways, leading to the activation of apoptosis. In vivo and in vitro supplementation with benfotiamine reactivates the pentose phosphate pathway and rescues CPC availability and function. This benefit is abrogated by either G6PD silencing by small interfering RNA (siRNA) or Akt inhibition by dominant-negative Akt. We provide new evidence of the negative impact of diabetes and high glucose on mechanisms controlling CPC redox state and survival. Boosting the pentose phosphate pathway might represent a novel mechanistic target for protection of CPC integrity.

Phytochemistry of cimicifugic acids and associated bases in Cimicifuga racemosa root extracts.

PubMed

Gödecke, Tanja; Nikolic, Dejan; Lankin, David C; Chen, Shao-Nong; Powell, Sharla L; Dietz, Birgit; Bolton, Judy L; van Breemen, Richard B; Farnsworth, Norman R; Pauli, Guido F

2009-01-01

Earlier studies reported serotonergic activity for cimicifugic acids (CA) isolated from Cimicifuga racemosa. The discovery of strongly basic alkaloids, cimipronidines, from the active extract partition and evaluation of previously employed work-up procedures has led to the hypothesis of strong acid/base association in the extract. Re-isolation of the CAs was desired to permit further detailed studies. Based on the acid/base association hypothesis, a new separation scheme of the active partition was required, which separates acids from associated bases. A new 5-HT(7) bioassay guided work-up procedure was developed that concentrates activity into one partition. The latter was subjected to a new two-step centrifugal partitioning chromatography (CPC) method, which applies pH zone refinement gradient (pHZR CPC) to dissociate the acid/base complexes. The resulting CA fraction was subjected to a second CPC step. Fractions and compounds were monitored by (1)H NMR using a structure-based spin-pattern analysis facilitating dereplication of the known acids. Bioassay results were obtained for the pHZR CPC fractions and for purified CAs. A new CA was characterised. While none of the pure CAs was active, the serotonergic activity was concentrated in a single pHZR CPC fraction, which was subsequently shown to contain low levels of the potent 5-HT(7) ligand, N(omega)-methylserotonin. This study shows that CAs are not responsible for serotonergic activity in black cohosh. New phytochemical methodology (pHZR CPC) and a sensitive dereplication method (LC-MS) led to the identification of N(omega)-methylserotonin as serotonergic active principle. Copyright (c) 2009 John Wiley & Sons, Ltd.

Phytochemistry of Cimicifugic Acids and Associated Bases in Cimicifuga racemosa Root Extracts

PubMed Central

GÖdecke, Tanja; Nikolic, Dejan; Lankin, David C.; Chen, Shao-Nong; Powell, Sharla L.; Dietz, Birgit; Bolton, Judy L.; Van Breemen, Richard B.; Farnsworth, Norman R.; Pauli, Guido F.

2009-01-01

Introduction Earlier studies reported serotonergic activity for cimicifugic acids (CA) isolated from Cimicifuga racemosa. The discovery of strongly basic alkaloids, cimipronidines, from the active extract partition and evaluation of previously employed work-up procedures has led to the hypothesis of strong acid/base association in the extract. Objective Re-isolation of the CAs was desired to permit further detailed studies. Based on the acid/base association hypothesis, a new separation scheme of the active partition was required, which separates acids from associated bases. Methodology A new 5-HT7 bioassay guided work-up procedure was developed that concentrates activity into one partition. The latter was subjected to a new 2-step centrifugal partitioning chromatography (CPC) method, which applies pH zone refinement gradient (pHZR CPC) to dissociate the acid/base complexes. The resulting CA fraction was subjected to a second CPC step. Fractions and compounds were monitored by 1H NMR using a structure based spin-pattern analysis facilitating dereplication of the known acids. Bioassay results were obtained for the pHZR CPC fractions and for purified CAs. Results A new CA was characterized. While none of the pure CAs was active, the serotonergic activity was concentrated in a single pHZR CPC fraction, which was subsequently shown to contain low levels of the potent 5-HT7 ligand, Nω–methylserotonin. Conclusion This study shows that CAs are not responsible for serotonergic activity in black cohosh. New phytochemical methodology (pHZR CPC) and a sensitive dereplication method (LC-MS) led to the identification of Nω–methylserotonin as serotonergic active principle. PMID:19140115

[Prenatal diagnosis and treatment of fetal choroid plexus cysts].

PubMed

Liang, Mei-Ying; Wang, Hong-Bin; Huang, Xin; Wei, Yan-Qiu

2007-09-01

To discuss the clinical management and significance of the prenatal diagnosis of Fetal Choroid Plexus Cysts (CPC). From May 2004 to March 2007, 55 cases of fetal CPC diagnosed by B-ultrasound during second trimester were prospectively studied. Each case was studied regarding fetal chromosome karyotype, disappearance weeks of the cyst, the clinical outcome and follow-up results respectively. The cases were diagnosed during 16 - 25 gestational weeks. The diameters of the cysts varied from 0.2 cm to 2.4 cm. There were 25 cases of bilateral cysts and 30 cases of unilateral or 50 cases of isolated CPC and 5 cases of complicated CPC. The cysts of all cases who continued pregnancy disappeared before 28 weeks. Fetal chromosome karyotypes were obtained in 50 cases. Among them, two cases were 18-trisomy, and one case was 21-trisomy. Five cases were terminated pregnancy because of abnormal chromosome karyotype or malformation during second trimester. One neonate was diagnosed as ventricular septal defect among 50 cases of follow up. Among these six cases, three were from advanced-age pregnant women, five cases were with abnormal fetal structure and five cases were with the diameter of bilateral or unilateral cysts more than 1.0 cm. (1) Fetal CPC can be diagnosed during second trimester, and the majority disappear before 28 gestational weeks. (2) High risk factors for fetal abnormal chromosome karyotype may be: advanced-age pregnant women, abnormal structure of fetus, and the diameter of bilateral or unilateral cyst more than 1.0 cm. It is suggested that fetal CPC with the high risks should receive fetal chromosome karyotype test during pregnancy.

Boosting the pentose phosphate pathway restores cardiac progenitor cell availability in diabetes

PubMed Central

Katare, Rajesh; Oikawa, Atsuhiko; Cesselli, Daniela; Beltrami, Antonio P.; Avolio, Elisa; Muthukrishnan, Deepti; Munasinghe, Pujika Emani; Angelini, Gianni; Emanueli, Costanza; Madeddu, Paolo

2013-01-01

Aims Diabetes impinges upon mechanisms of cardiovascular repair. However, the biochemical adaptation of cardiac stem cells to sustained hyperglycaemia remains largely unknown. Here, we investigate the molecular targets of high glucose-induced damage in cardiac progenitor cells (CPCs) from murine and human hearts and attempt safeguarding CPC viability and function through reactivation of the pentose phosphate pathway. Methods and results Type-1 diabetes was induced by streptozotocin. CPC abundance was determined by flow cytometry. Proliferating CPCs were identified in situ by immunostaining for the proliferation marker Ki67. Diabetic hearts showed marked reduction in CPC abundance and proliferation when compared with controls. Moreover, Sca-1pos CPCs isolated from hearts of diabetic mice displayed reduced activity of key enzymes of the pentose phosphate pathway, glucose-6-phosphate dehydrogenase (G6PD), and transketolase, increased levels of superoxide and advanced glucose end-products (AGE), and inhibition of the Akt/Pim-1/Bcl-2 signalling pathway. Similarly, culture of murine CPCs or human CD105pos progenitor cells in high glucose inhibits the pentose phosphate and pro-survival signalling pathways, leading to the activation of apoptosis. In vivo and in vitro supplementation with benfotiamine reactivates the pentose phosphate pathway and rescues CPC availability and function. This benefit is abrogated by either G6PD silencing by small interfering RNA (siRNA) or Akt inhibition by dominant-negative Akt. Conclusion We provide new evidence of the negative impact of diabetes and high glucose on mechanisms controlling CPC redox state and survival. Boosting the pentose phosphate pathway might represent a novel mechanistic target for protection of CPC integrity. PMID:22997160

Glomeruloid Microvascular Proliferation, Desmoplasia, and High Proliferative Index as Potential Indicators of High Grade Canine Choroid Plexus Tumors.

PubMed

Muscatello, Luisa Vera; Avallone, Giancarlo; Serra, Fabienne; Seuberlich, Torsten; Mandara, Maria Teresa; Sisó, Silvia; Brunetti, Barbara; Oevermann, Anna

2018-05-01

Choroid plexus tumors (CPT) are intraventricular neoplasms accounting for 10% of all primary central nervous system tumors in dogs. They are frequently classified according to the human WHO classification into choroid plexus papilloma (CPP, grade I), atypical CPP (aCPP, grade II), and choroid plexus carcinoma (CPC, grade III). Histological features observed in canine CPT such as increased vascular density (IVD) and glomeruloid microvascular proliferation (GMVP) are not part of the WHO classification. This multi-centric study aimed to investigate tumor-associated vascular hyperplasia in dogs by determining the prevalence of GMVP and IVD in 52 canine CPT and their association with tumor grade. In addition, the expression of angiogenic factors was assessed by immunohistochemistry in 25 tumors to investigate the pathogenesis of tumor-associated vascular hyperplasia. Based on the classical histological hallmarks, this study of 52 CPT identified 22 (42%) CPP (grade I) and 30 of (58%) CPC (grade III). GMVP was more prevalent in CPC (13/30; 43%) than CPP (1/22; 4%), whereas IVD occurred to a similar extent in CPP and CPC. Desmoplasia was more common in CPC (19/30; 63%) than CPP (2/22; 9%), and similarly, the proliferative index (PI) of neoplastic epithelium was significantly higher in CPC (5.14%) than CPP (0.94%). The majority of CPT expressed platelet-derived growth factor (PDGF), PDGFRα, PDGFRβ, and vascular endothelial growth factor (VEGF) irrespective of tumor grade or tumor-associated vascular hyperplasia. These results suggest that tumor-associated GMVP, desmoplasia, and PI may serve as histological indicators of malignancy in CPT.

Transcriptional regulation of crystallin, redox, and apoptotic genes by C-Phycocyanin in the selenite-induced cataractogenic rat model

PubMed Central

Kumari, Rasiah Pratheepa; Ramkumar, Srinivasagan; Thankappan, Bency; Natarajaseenivasan, Kalimuthusamy; Balaji, Sadhasivam

2015-01-01

Purpose This study was designed to examine the constrictive potential of C-Phycocyanin (C-PC) in regulating changes imposed on gene expression in the selenite-induced cataract model. Methods Wistar rat pups were divided into three groups of eight each. On P10, Group I received an intraperitoneal injection of normal saline. Groups II and III received a subcutaneous injection of sodium selenite (19 μmol/kg bodyweight); Group III also received an intraperitoneal injection of C-PC (200 mg/kg bodyweight) on P9–14. Total RNA was isolated on P16, and the relative abundance of mRNA of the crystallin structural genes, redox components, and apoptotic cascade were ascertained with real-time PCR with reference to the internal control β-actin. Results Real-time PCR analysis showed the crystallin genes (αA-, βB1-, γD-) and redox cycle components (Cat, SOD-1, Gpx) were downregulated, the apoptotic components were upregulated, and antiapoptotic Bcl-2 was downregulated in Group II. Treatment with 200 mg/kg bodyweight C-PC (Group III) transcriptionally regulated the instability of the expression of these genes, thus ensuring C-PC is a prospective anticataractogenic agent that probably delays the onset and progression of cataractogenesis induced by sodium selenite. Conclusions C-PC treatment possibly prevented cataractogenesis triggered by sodium selenite, by regulating the lens crystallin, redox genes, and apoptotic cascade mRNA expression and thus maintains lens transparency. C-PC may be developed as a potential antioxidant compound applied in the future to prevent and treat age-related cataract. PMID:25593511

The Inhibitory Effect of C-phycocyanin Containing Protein Extract (C-PC Extract) on Human Matrix Metalloproteinases (MMP-2 and MMP-9) in Hepatocellular Cancer Cell Line (HepG2).

PubMed

Kunte, Mugdha; Desai, Krutika

2017-06-01

Spirulina platensis :have been studied for several biological activities. In the current study C-phycocyanin containing protein extract (C-PC extract) of Spirulina platensis have been studied for its effect on human matrix metalloproteinases (MMP-1, MMP-2 and MMP-9) and tissue inhibitors of MMPs (TIMP-1 and TIMP-2). In the present study, breast cancer cell line (MDA-MB 231) and hepatocellular cancer cell line (HepG2) were examined for inhibition of MMPs at different levels of expression after C-PC extract treatment. Herein, we have demonstrated that C-PC extract significantly reduced activity of MMP-2 by 55.13% and MMP-9 by 57.9% in HepG2 cells at 15 μg concentration. Additionally, the treatment has reduced mRNA expression of MMP-2 and MMP-9 at 20 μg concentration by 1.65-folds and 1.66-folds respectively. The C-PC extract treatment have also downregulated a mRNA expression of TIMP-2 by 1.12 folds at 20 μg concentration in HepG2 cells. Together, these results indicate that C-PC, extract successfully inhibited MMP-2 and -9 at different levels of expression and TIMP-2 at a mRNA expression level; however, extract did not have any effect on MMP-1 expressed in MDA-MB231 and TIMP-1 expressed in HepG2 cells as well as the exact mechanism of inhibition of MMP-2, MMP-9 and TIMP-2 remained unclear.

Measuring sexual dimorphism with a race-gender face space.

PubMed

Hopper, William J; Finklea, Kristin M; Winkielman, Piotr; Huber, David E

2014-10-01

Faces are complex visual objects, and faces chosen to vary in 1 regard may unintentionally vary in other ways, particularly if the correlation is a property of the population of faces. Here, we present an example of a correlation that arises from differences in the degree of sexual dimorphism. In Experiment 1, paired similarity ratings were collected for a set of 40 real face images chosen to vary in terms of gender and race (Asian vs. White). Multidimensional scaling (MDS) placed these stimuli in a "face space," with different attributes corresponding to different dimensions. Gender was found to vary more for White faces, resulting in a negative or positive correlation between gender and race when only considering male or only considering female faces. This increased sexual dimorphism for White faces may provide an alternative explanation for differences in face processing between White and Asian faces (e.g., the own-race bias, face attractiveness biases, etc.). Studies of face processing that are unconfounded by this difference in the degree of sexual dimorphism require stimuli that are decorrelated in terms of race and gender. Decorrelated faces were created using a morphing technique, spacing the morphs uniformly around a ring in the 2-dimensional (2D) race-gender plane. In Experiment 2, paired similarity ratings confirmed the 2D positions of the morph faces. In Experiment 3, race and gender category judgments varied uniformly for these decorrelated stimuli. Our results and stimuli should prove useful for studying sexual dimorphism and for the study of face processing more generally.

Germination season and watering regime, but not seed morph, affect life history traits in a cold desert diaspore-heteromorphic annual.

PubMed

Lu, Juan J; Tan, Dun Y; Baskin, Jerry M; Baskin, Carol C

2014-01-01

Seed morph, abiotic conditions and time of germination can affect plant fitness, but few studies have tested their combined effects on plasticity of plant life history traits. Thus, we tested the hypothesis that seed morph, germination season and watering regime influence phenotypic expression of post-germination life history traits in the diaspore-heteromorphic cold desert winter annual/spring ephemeral Diptychocarpus strictus. The two seed morphs were sown in watered and non-watered plots in late summer, and plants derived from them were watered or not-watered throughout the study. Seed morph did not affect phenology, growth and morphology, survival, dry mass accumulation and allocation or silique and seed production. Seeds in watered plots germinated in autumn (AW) and spring (SW) but only in spring for non-watered plots (SNW). A high percentage of AW, SW and SNW plants survived and reproduced, but flowering date and flowering period of autumn- vs. spring-germinated plants differed. Dry mass also differed with germination season/watering regime (AW > SW > SNW). Number of siliques and seeds increased with plant size (AW > SW > SNW), whereas percent dry mass allocated to reproduction was higher in small plants: SNW > SW > AW. Thus, although seed morph did not affect the expression of life history traits, germination season and watering regime significantly affected phenology, plant size and accumulation and allocation of biomass to reproduction. Flexibility throughout the life cycle of D. strictus is an adaptation to the variation in timing and amount of rainfall in its cold desert habitat.

Localization and Divergent Profiles of Estrogen Receptors and Aromatase in the Vocal and Auditory Networks of a Fish with Alternative Mating Tactics

PubMed Central

Fergus, Daniel J.; Bass, Andrew H.

2013-01-01

Estrogens play a salient role in the development and maintenance of both male and female nervous systems and behaviors. The plainfin midshipman (Porichthys notatus), a teleost fish, has two male reproductive morphs that follow alternative mating tactics and diverge in multiple somatic, hormonal and neural traits, including the central control of morph-specific vocal behaviors. After we identified duplicate estrogen receptors (ERβ1 and ERβ2) in midshipman, we developed antibodies to localize protein expression in the central vocal-acoustic networks and saccule, the auditory division of the inner ear. As in other teleost species, ERβ1 and ERβ2 were robustly expressed in the telencephalon and hypothalamus in vocal-acoustic and other brain regions shown previously to exhibit strong expression of ERα and aromatase (estrogen synthetase, CYP19) in midshipman. Like aromatase, ERβ1 label co-localized with glial fibrillary acidic protein (GFAP) in telencephalic radial glial cells. Quantitative PCR revealed similar patterns of transcript abundance across reproductive morphs for ERβ1, ERβ2, ERα and aromatase in the forebrain and saccule. In contrast, transcript abundance for ERs and aromatase varied significantly between morphs in and around the sexually polymorphic vocal motor nucleus (VMN). Together, the results suggest that VMN is the major estrogen target within the estrogen-sensitive hindbrain vocal network that directly determines the duration, frequency and amplitude of morph-specific vocalizations. Comparable regional differences in steroid receptor abundances likely regulate morph-specific behaviors in males and females of other species exhibiting alternative reproductive tactics. PMID:23460422

Strengthening Multipayer Collaboration: Lessons From the Comprehensive Primary Care Initiative.

PubMed

Anglin, Grace; Tu, H A; Liao, Kristie; Sessums, Laura; Taylor, Erin Fries

2017-09-01

Policy Points: Collaboration across payers to align financial incentives, quality measurement, and data feedback to support practice transformation is critical, but challenging due to competitive market dynamics and competing institutional priorities. The Centers for Medicare & Medicaid Services or other entities convening multipayer initiatives can build trust with other participants by clearly outlining each participant's role and the parameters of collaboration at the outset of the initiative. Multipayer collaboration can be improved if participating payers employ neutral, proactive meeting facilitators; develop formal decision-making processes; seek input on decisions from practice representatives; and champion the initiative within their organizations. With increasing frequency, public and private payers are joining forces to align goals and resources for primary care transformation. However, sustaining engagement and achieving coordination among payers can be challenging. The Comprehensive Primary Care (CPC) initiative is one of the largest multipayer initiatives ever tested. Drawing on the experience of the CPC initiative, this paper examines the factors that influence the effectiveness of multipayer collaboration. This paper draws largely on semistructured interviews with CPC-participating payers and payer conveners that facilitated CPC discussions and on observation of payer meetings. We coded and analyzed these qualitative data to describe collaborative dynamics and outcomes and assess the factors influencing them. We found that several factors appeared to increase the likelihood of successful payer collaboration: contracting with effective, neutral payer conveners; leveraging the support of payer champions, and seeking input on decisions from practice representatives. The presence of these factors helped some CPC regions overcome significant initial barriers to achieve common goals. We also found that leadership from the Centers for Medicare & Medicaid Services (CMS) was key to achieving broad payer engagement in CPC, but CMS's dual role as initiative convener and participating payer at times made collaboration challenging. CMS was able to build trust with other payers by clarifying which parts of CPC could be adapted to regional contexts, deferring to other payers for these decisions, and increasing opportunities for payers to meet with CMS representatives. CPC demonstrates that when certain facilitating factors are present, payers can overcome competitive market dynamics and competing institutional priorities to align financial incentives, quality measurement, and data feedback to support practice transformation. Lessons from this large-scale, multipayer initiative may be helpful for other multipayer efforts getting under way. © 2017 Milbank Memorial Fund.

Syn-extensional plutonism and peak metamorphism in the albion-raft river-grouse creek metamorphic core complex

USGS Publications Warehouse

Strickland, A.; Miller, E.L.; Wooden, J.L.; Kozdon, R.; Valley, J.W.

2011-01-01

The Cassia plutonic complex (CPC) is a group of variably deformed, Oligocene granitic plutons exposed in the lower plate of the Albion-Raft River- Grouse Creek (ARG) metamorphic core complex of Idaho and Utah. The plutons range from granodiorite to garnet-bearing, leucogranite, and during intrusion, sillimanite- grade peak metamorphism and ductile attenuation occurred in the country rocks and normal-sense, amphibolite-grade deformation took place along the Middle Mountain shear zone. U-Pb zircon geochronology from three variably deformed plutons exposed in the lower plate of the ARG metamorphic core complex revealed that each zircon is comprised of inherited cores (dominantly late Archean) and Oligocene igneous overgrowths. Within each pluton, a spread of concordant ages from the Oligocene zircon overgrowths is interpreted as zircon recycling within a long-lived magmatic system. The plutons of the CPC have very low negative whole rock ??Nd values of -26 to -35, and initial Sr values of 0.714 to 0.718, consistent with an ancient, crustal source. Oxygen isotope ratios of the Oligocene zircon overgrowths from the CPC have an average ??18O value of 5.40 ?? 0.63 permil (2SD, n = 65) with a slight trend towards higher ??18O values through time. The ??18O values of the inherited cores of the zircons are more variable at 5.93 ?? 1.51 permil (2SD, n = 29). Therefore, we interpret the plutons of the CPC as derived, at least in part, from melting Archean crust based on the isotope geochemistry. In situ partial melting of the exposed Archean basement that was intruded by the Oligocene plutons of the CPC is excluded as the source for the CPC based on field relationships, age and geochemistry. Correlations between Ti and Hf concentrations in zircons from the CPC suggest that the magmatic system may have become hotter (higher Ti concentration in zircon) and less evolved (lower Hf in zircon concentration) through time. Therefore, the CPC represents prolonged or episodic magmatism system (32-25 Ma), and the intrusions were each accompanied by sillimanite-grade deformation and extension. The Oligocene magmatism and peak metamorphism preserved in the ARG metamorphic core complex are likely related to regional trends in mantle-derived magmatism that led to protracted heating, melting and mobilization of the deeper crust.

Colour polymorphic lures exploit innate preferences for spectral versus luminance cues in dipteran prey.

PubMed

White, Thomas E; Kemp, Darrell J

2017-08-14

Theory predicts that colour polymorphism may be favored by variation in the visual context under which signals are perceived. The context encompasses all environmental determinants of light availability and propagation, but also the dynamics of perception in receivers. Color vision involves the neural separation of information into spectral versus luminance channels, which often differentially guide specific tasks. Here we explicitly tested whether this discrete perceptual basis contributes to the maintenance of polymorphism in a prey-luring system. The orb-weaving spider Gasteracantha fornicata is known to attract a broad community of primarily dipteran prey due to their conspicuous banded dorsal signal. They occur in two morphs ("white" and "yellow") which should, respectively, generate greater luminance and color contrast in the dipteran eye. Given that arthropods often rely upon luminance-versus-spectral cues for relatively small-versus-large stimulus detection, we predicted a switch in relative attractiveness among morphs according to apparent spider size. Our experimental tests used colour-naïve individuals of two known prey species (Drosophila hydei and Musca domestica) in replicate Y-maze choice trials designed to manipulate the apparent size of spider models via the distance at which they are viewed. Initial trials confirmed that flies were attracted to each G. fornicata morph in single presentations. When given a simultaneous choice between morphs against a viewing background typical of those encountered in nature, flies exhibited no preference regardless of the visual angle subtended by models. However, when backgrounds were adjusted to nearer the extremes of those of each morph in the wild, flies were more attracted by white morphs when presented at longer range (consistent with a reliance on achromatic cues), yet were unbiased in their close-range choice. While not fully consistent with predictions (given the absence of a differential preference for stimuli at close range), our results demonstrate an effect of apparent stimulus size upon relative morph attractiveness in the direction anticipated from present knowledge of fly visual ecology. This implies the potential tuning of G. fornicata morph signal structure according to a perceptual feature that is likely common across their breadth of arthropod prey, and complements recent observational work in suggesting a candidate mechanism for the maintenance of deceptive polymorphism through the exploitation of different visual channels in prey.

TweezPal - Optical tweezers analysis and calibration software

NASA Astrophysics Data System (ADS)

Osterman, Natan

2010-11-01

Optical tweezers, a powerful tool for optical trapping, micromanipulation and force transduction, have in recent years become a standard technique commonly used in many research laboratories and university courses. Knowledge about the optical force acting on a trapped object can be gained only after a calibration procedure which has to be performed (by an expert) for each type of trapped objects. In this paper we present TweezPal, a user-friendly, standalone Windows software tool for optical tweezers analysis and calibration. Using TweezPal, the procedure can be performed in a matter of minutes even by non-expert users. The calibration is based on the Brownian motion of a particle trapped in a stationary optical trap, which is being monitored using video or photodiode detection. The particle trajectory is imported into the software which instantly calculates position histogram, trapping potential, stiffness and anisotropy. Program summaryProgram title: TweezPal Catalogue identifier: AEGR_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEGR_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 44 891 No. of bytes in distributed program, including test data, etc.: 792 653 Distribution format: tar.gz Programming language: Borland Delphi Computer: Any PC running Microsoft Windows Operating system: Windows 95, 98, 2000, XP, Vista, 7 RAM: 12 Mbytes Classification: 3, 4.14, 18, 23 Nature of problem: Quick, robust and user-friendly calibration and analysis of optical tweezers. The optical trap is calibrated from the trajectory of a trapped particle undergoing Brownian motion in a stationary optical trap (input data) using two methods. Solution method: Elimination of the experimental drift in position data. Direct calculation of the trap stiffness from the positional variance. Calculation of 1D optical trapping potential from the positional distribution of data points. Trap stiffness calculation by fitting a parabola to the trapping potential. Presentation of X-Y positional density for close inspection of the 2D trapping potential. Calculation of the trap anisotropy. Running time: Seconds

Markovian Monte Carlo program EvolFMC v.2 for solving QCD evolution equations

NASA Astrophysics Data System (ADS)

Jadach, S.; Płaczek, W.; Skrzypek, M.; Stokłosa, P.

2010-02-01

We present the program EvolFMC v.2 that solves the evolution equations in QCD for the parton momentum distributions by means of the Monte Carlo technique based on the Markovian process. The program solves the DGLAP-type evolution as well as modified-DGLAP ones. In both cases the evolution can be performed in the LO or NLO approximation. The quarks are treated as massless. The overall technical precision of the code has been established at 5×10. This way, for the first time ever, we demonstrate that with the Monte Carlo method one can solve the evolution equations with precision comparable to the other numerical methods. New version program summaryProgram title: EvolFMC v.2 Catalogue identifier: AEFN_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEFN_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including binary test data, etc.: 66 456 (7407 lines of C++ code) No. of bytes in distributed program, including test data, etc.: 412 752 Distribution format: tar.gz Programming language: C++ Computer: PC, Mac Operating system: Linux, Mac OS X RAM: Less than 256 MB Classification: 11.5 External routines: ROOT ( http://root.cern.ch/drupal/) Nature of problem: Solution of the QCD evolution equations for the parton momentum distributions of the DGLAP- and modified-DGLAP-type in the LO and NLO approximations. Solution method: Monte Carlo simulation of the Markovian process of a multiple emission of partons. Restrictions:Limited to the case of massless partons. Implemented in the LO and NLO approximations only. Weighted events only. Unusual features: Modified-DGLAP evolutions included up to the NLO level. Additional comments: Technical precision established at 5×10. Running time: For the 10 6 events at 100 GeV: DGLAP NLO: 27s; C-type modified DGLAP NLO: 150s (MacBook Pro with Mac OS X v.10.5.5, 2.4 GHz Intel Core 2 Duo, gcc 4.2.4, single thread).

MEM application to IRAS CPC images

NASA Technical Reports Server (NTRS)

Marston, A. P.

1994-01-01

A method for applying the Maximum Entropy Method (MEM) to Chopped Photometric Channel (CPC) IRAS additional observations is illustrated. The original CPC data suffered from problems with repeatability which MEM is able to cope with by use of a noise image, produced from the results of separate data scans of objects. The process produces images of small areas of sky with circular Gaussian beams of approximately 30 in. full width half maximum resolution at 50 and 100 microns. Comparison is made to previous reconstructions made in the far-infrared as well as morphologies of objects at other wavelengths. Some projects with this dataset are discussed.

Nonimaging concentrators for solar thermal energy

NASA Astrophysics Data System (ADS)

Winston, R.; Gallagher, J. J.

1980-03-01

A small experimental solar collector test facility was used to explore applications of nonimaging optics for solar thermal concentration in three substantially different configurations: a single stage system with moderate concentration on an evacuated absorber (a 5.25X evacuated tube Compound Parabolic Concentrator or CPC), a two stage system with high concentration and a non-evacuated absorber (a 16X Fresnel lens/CPC type mirror) and moderate concentration single stage systems with non-evacuated absorbers for lower temperature (a 3X and a 6.5X CPC). Prototypes of each of these systems were designed, built and tested. The performance characteristics are presented.

Reflectometer design using nonimaging optics

NASA Astrophysics Data System (ADS)

Snail, Keith A.

1987-12-01

A new type of two-stage reflectometer is proposed for the measurement of directional hemispherical reflectance. The proposed reflectometer consists of a primary collecting mirror coupled to a secondary mirror chosen to eliminate the Fresnel variation of the detector (or source) response. The secondary mirror shape needed is an inverted nonimaging compound parabolic concentrator (CPC). For direct mode operation, the detector is placed at the larger CPC aperture. Ray tracing of a CPC/ellipsoid reflectometer indicates that the throughput is high and isotropic. Design trade-offs and two-stage reflectometers employing a hemisphere and dual paraboloid primary are also discussed.

Reflectometer design using nonimaging optics.

PubMed

Snail, K A

1987-12-15

A new type of two-stage reflectometer is proposed for the measurement of directional hemispherical reflectance. The proposed reflectometer consists of a primary collecting mirror coupled to a secondary mirror chosen to eliminate the Fresnel variation of the detector (or source) response. The secondary mirror shape needed is an inverted nonimaging compound parabolic concentrator (CPC). For direct mode operation, the detector is placed at the larger CPC aperture. Ray tracing of a CPC/ellipsoid reflectometer indicates that the throughput is high and isotropic. Design trade-offs and two-stage reflectometers employing a hemisphere and dual paraboloid primary are also discussed.

Higher production of C-phycocyanin by nitrogen-free (diazotrophic) cultivation of Nostoc sp. NK and simplified extraction by dark-cold shock.

PubMed

Lee, Na Kyeong; Oh, Hee-Mock; Kim, Hee-Sik; Ahn, Chi-Yong

2017-03-01

Nostoc sp. NK (KCTC 12772BP) was isolated and cultivated in a BG11 medium and a nitrate-free BG11 medium (BG11 0 ). To enhance C-phycocyanin (C-PC) content in the cells, different fluorescent lamps (white, plant, and red) were used as light sources for complementary chromatic adaptation (CCA). The maximum biomass productivity was 0.42g/L/d and 0.32g/L/d under BG11 and BG11 0 conditions, respectively. The maximum C-PC contents were 8.4% (w/w) under white lamps, 13.6% (w/w) under plant lamps, and 18% (w/w) under BG11 0 and the red light condition. The maximum C-PC productivity was 57.4mg/L/d in BG11 0 under the red lamp condition. These results indicate that a higher C-PC content could be obtained under a diazotrophic condition and a CCA reaction. The C-PC could be released naturally from cells without any extraction processes, when Nostoc sp. NK was cultivated in the BG11 0 medium with CO 2 aeration and put in dark conditions at 5°C. Copyright © 2016 Elsevier Ltd. All rights reserved.

Brittle and ductile adjustable cement derived from calcium phosphate cement/polyacrylic acid composites.

PubMed

Chen, Wen-Cheng; Ju, Chien-Ping; Wang, Jen-Chyan; Hung, Chun-Cheng; Chern Lin, Jiin-Huey

2008-12-01

Bone filler has been used over the years in dental and biomedical applications. The present work is to characterize a non-dispersive, fast setting, modulus adjustable, high bioresorbable composite bone cement derived from calcium phosphate-based cement combined with polymer and binding agents. This cement, we hope, will not swell in simulated body fluid and keep the osteogenetic properties of the dry bone and avoid its disadvantages of being brittle. We developed a calcium phosphate cement (CPC) of tetracalcium phosphate/dicalcium phosphate anhydrous (TTCP/DCPA)-polyacrylic acid with tartaric acid, calcium fluoride additives and phosphate hardening solution. The results show that while composite, the hard-brittle properties of 25wt% polyacrylic acid are proportional to CPC and mixing with additives is the same as those of the CPC without polyacrylic acid added. With an increase of polyacrylic acid/CPC ratio, the 67wt% samples revealed ductile-tough properties and 100wt% samples kept ductile or elastic properties after 24h of immersion. The modulus range of this development was from 200 to 2600MPa after getting immersed in simulated body fluid for 24h. The TTCP/DCPA-polyacrylic acid based CPC demonstrates adjustable brittle/ductile strength during setting and after immersion, and the final reaction products consist of high bioresorbable monetite/brushite/calcium fluoride composite with polyacrylic acid.

Circulating progenitor cells during exercise, muscle electro-stimulation and intermittent hypobaric hypoxia in patients with traumatic brain injury: a pilot study.

PubMed

Corral, Luisa; Conde, Laura; Guillamó, Elisabet; Blasi, Juan; Juncadella, Montserrat; Javierre, Casimiro; Viscor, Ginés; Ventura, Josep L

2014-01-01

Circulating progenitor cells (CPC) treatments may have great potential for the recovery of neurons and brain function. To increase and maintain CPC with a program of exercise, muscle electro-stimulation (ME) and/or intermittent-hypobaric-hypoxia (IHH), and also to study the possible improvement in physical or psychological functioning of participants with Traumatic Brain Injury (TBI). Twenty-one participants. Four groups: exercise and ME group (EEG), cycling group (CyG), IHH and ME group (HEG) and control group (CG). Psychological and physical stress tests were carried out. CPC were measured in blood several times during the protocol. Psychological tests did not change. In the physical stress tests the VO2 uptake increased in the EEG and the CyG, and the maximal tolerated workload increased in the HEG. CPC levels increased in the last three weeks in EEG, but not in CyG, CG and HEG. CPC levels increased in the last three weeks of the EEG program, but not in the other groups and we did not detect performed psychological test changes in any group. The detected aerobic capacity or workload improvement must be beneficial for the patients who have suffered TBI, but exercise type and the mechanisms involved are not clear.

Influence of surfactants and humic acids on Artemia Franciscana's embryonic phospho-metabolite profile as measured by 31P NMR.

PubMed

Deese, Rachel D; Weldeghiorghis, Thomas K; Haywood, Benjamin J; Cook, Robert L

2017-05-01

Surfactants, such as triton X-100 (Tx-100), cetylpyridinium chloride (CPC), and sodium dodecyl sulfate (SDS) are known to be toxic to Artemia Franciscana (Artemia) - an organism, frequently used to monitor the health of the aquatic environment. The phospho-metabolite profile of a living organism is often indicative of imbalances that may have been caused by environmental stressors, such as surfactants. This study utilizes in vivo 31 P NMR to monitor temporal changes in the phospho-metabolite profile of Artemia caused by Tx-100, CPC, and SDS and the ability of humic acid (HA) to mitigate the toxicity of these surfactants. It was found that, while Tx-100 does not have any effect on the phospho-metabolite profile, both CPC and SDS cause a complete retardation in growth of the phosphodiester (PDE) peak in the 31 P NMR spectrum, which is indicative of the inhibited cell replication. This growth inhibition was independently verified by the decreased guanosine triphosphate (GTP) concentration in the CPC and SDS-exposed Artemia. In addition, upon introduction of HA to the CPC and SDS-exposed Artemia, an increase of PDE peak over time is indicative of HA mitigating toxicity. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Liquid Crystalline Systems Containing Antimicrobial Compounds on Infectious Skin Bacteria.

PubMed

Souza, Carla; Watanabe, Evandro; Aires, Carolina Patrícia; Lara, Marilisa Guimarães

2017-08-01

This study aimed (i) to prepare liquid crystalline systems (LCS) of glyceryl monooleate (GMO) and water containing antibacterial compounds and (ii) to evaluate their potential as drug delivery systems for topical treatment of bacterial infections. Therefore, LCS containing CPC (cetylpyridinium chloride) (LCS/CPC) and PHMB (poly(hexamethylene biguanide) hydrochloride) (LCS/PHMB) were prepared and the liquid crystalline phases were identified by polarizing light microscopy 24 h and 7 days after preparation. The in vitro drug release profile and in vitro antibacterial activity of the systems were assessed using the double layer agar diffusion method against Staphylococcus aureus, methicillin-resistant S. aureus, Staphylococcus epidermidis, Escherichia coli, and Enterococcus faecalis. The interaction between GMO and the drugs was evaluated by a drug absorption study. Stable liquid crystalline systems containing CPC and PHMB were obtained. LCS/PHMB decreased the PHMB release rate and exerted strong antibacterial activity against all the investigated bacteria. In contrast, CPC interacted with GMO so strongly that it became attached to the system; the amount released was not sufficient to exert antibacterial activity. Therefore, the studied liquid crystalline systems were suitable to deliver PHMB, but not CPC. Accordingly, it was demonstrated that GMO interacts with each drug differently, which may interfere in the final efficiency of GMO/water LCS.

In-vitro evidence for efficacy of antimicrobial mouthrinses

PubMed Central

Pan, Pauline C.; Harper, Scott; Ricci-Nittel, Danette; Lux, Renate; Shi, Wenyuan

2010-01-01

SUMMARY Objectives The objective of this study was to compare the antimicrobial activity of commercially available antiseptic mouthrinses against saliva-derived plaque biofilms in static and flow-through biofilm systems in vitro. Methods Nine mouthrinses were tested in a recirculating flow-through biofilm model (RFTB) with viability assessment by ATP bioluminescence. In addition, five mouthrinses were evaluated in a batch chamber slide biofilm (BCSB) model, using live- dead staining and confocal laser scanning microscopy. Results In the RFTB model, essential oil (EO) and chlorhexidine (CHX)-containing rinses showed equivalent antimicrobial activity and were more effective than a range of cetyl pyridinium chloride (CPC1) formulations. In the BCSB model, twice-daily mouthrinse exposure demonstrated that the EO rinse was significantly more effective than rinses containing amine and stannous fluorides, a combination of CPC/CHX and CPC2. EO showed biofilm kill comparable to the CHX rinse. Conclusions The present studies have shown that mouthrinses vary significantly in their capability to kill plaque biofilm bacteria in BCSB and RFTB models. The EO mouthrinse demonstrated superior antiplaque biofilm activity to AFSF, CPC/CHX, and CPC rinses and comparable activity to CHX. The methods tested may be of value for the in-vitro screening of antiseptic rinses with different modes of antimicrobial action. PMID:20621239

Component Release and Mechanical Properties of Endodontic Sealers following Incorporation of Antimicrobial Agents

PubMed Central

Nicholson, John W.; Coleman, Nichola J.; Booth, Samantha; Dimkov, Aleksandar

2017-01-01

Root canal sealers with antimicrobial activity are highly beneficial; therefore, their antimicrobial properties could be improved by incorporation of antimicrobial agents. In the present study, the release of the quaternary ammonium compounds from endodontic sealers admixed with either benzalkonium chloride (BC) or cetylpyridinium chloride (CPC) at loadings of 2% wt was monitored. The effect of these additives on the compressive strengths and their release from the sealers was determined after 1 and 4 weeks. All of the materials studied were found to be capable of releasing antimicrobial additive in useful quantities. The release of CPC occurred to a statistically significant greater extent than BC for all materials. The addition of both BC and CPC generally decreased the compressive strength of all the endodontic sealers, with the exception of CPC in AH Plus, where the compressive strength was significantly increased. This suggests that, for these endodontic sealers, the antimicrobial additives alter the setting chemistry. AH Plus is an epoxy-based material cured with an amine, and in this case the increase in compressive strength with CPC is attributed to an enhanced cure reaction with this system. In all other cases, the additive inhibited the cure reaction to a greater or lesser extent. PMID:28620615

Morphing of spatial objects in real time with interpolation by functions of radial and orthogonal basis

NASA Astrophysics Data System (ADS)

Kosnikov, Yu N.; Kuzmin, A. V.; Ho, Hoang Thai

2018-05-01

The article is devoted to visualization of spatial objects’ morphing described by the set of unordered reference points. A two-stage model construction is proposed to change object’s form in real time. The first (preliminary) stage is interpolation of the object’s surface by radial basis functions. Initial reference points are replaced by new spatially ordered ones. Reference points’ coordinates change patterns during the process of morphing are assigned. The second (real time) stage is surface reconstruction by blending functions of orthogonal basis. Finite differences formulas are applied to increase the productivity of calculations.

Mechanical properties of shape memory polymers for morphing aircraft applications

NASA Astrophysics Data System (ADS)

Keihl, Michelle M.; Bortolin, Robert S.; Sanders, Brian; Joshi, Shiv; Tidwell, Zeb

2005-05-01

This investigation addresses basic characterization of a shape memory polymer (SMP) as a suitable structural material for morphing aircraft applications. Tests were performed for monotonic loading in high shear at constant temperature, well below, or just above the glass transition temperature. The SMP properties were time-and temperature-dependent. Recovery by the SMP to its original shape needed to be unfettered. Based on the testing SMPs appear to be an attractive and promising component in the solution for a skin material of a morphing aircraft. Their multiple state abilities allow them to easily change shape and, once cooled, resist large loads.

The melanocortin system regulates body pigmentation and social behaviour in a colour polymorphic cichlid fish†

PubMed Central

Maguire, Sean M.; Harris, Rayna M.; Rodriguez, Agosto A.; DeAngelis, Ross S.; Flores, Stephanie A.; Hofmann, Hans A.

2017-01-01

The melanocortin system is a neuroendocrine system that regulates a range of physiological and behavioural processes. We examined the extent to which the melanocortin system simultaneously regulates colour and behaviour in the cichlid fish Astatotilapia burtoni. We found that yellow males are more aggressive than blue males, in line with previous studies. We then found that exogenous α-melanocyte-stimulating hormone (α-MSH) increases yellowness of the body and dispersal of xanthophore pigments in both morphs. However, α-MSH had a morph-specific effect on aggression, with only blue males showing an increase in the rate of aggression. Exogenous agouti signalling peptide (ASIP), a melanocortin antagonist, did not affect coloration but reduced the rate of aggression in both colour morphs. Blue males had higher cortisol levels than yellow males. Neural gene expression of melanocortin receptors (mcr) and ligands was not differentially regulated between colour morphs. In the skin, however, mc1r and pro-opiomelanocortin (pomc) β were upregulated in blue males, while asip 1 was upregulated in yellow males. The effects of α-MSH on behaviour and body coloration, combined with morph-specific regulation of the stress response and the melanocortin system, suggest that the melanocortin system contributes to the polymorphism in behaviour and coloration in A. burtoni. PMID:28356453

A genetic approach to the rock-paper-scissors game.

PubMed

Barreto, Wendell P; Marquitti, Flavia M D; de Aguiar, Marcus A M

2017-05-21

Polymorphisms are usually associated with defenses and mating strategies, affecting the individual's fitness. Coexistence of different morphs is, therefore, not expected, since the fittest morph should outcompete the others. Nevertheless, coexistence is observed in many natural systems. For instance, males of the side-blotched lizards (Uta stansburiana) present three morphs with throat colors orange, yellow and blue, which are associated with mating strategies and territorial behavior. The three male morphs compete for females in a system that is well described by the rock-paper-scissors dynamics of game theory. Previous studies have modeled the lizards as hermaphroditic populations whose individual's behavior were determined only by their phenotypes. Here we consider an extension of this dynamical system where diploidy and sexual reproduction are explicitly taken into account. Similarly to the lizards we represent the genetic system by a single locus with three alleles, o, y, and b in a diploid chromosome with dominance of o over y and of y over b. We show that this genotypic description of the dynamics results in the same equilibrium phenotype frequencies as the phenotypic models, but affects the stability of the system, changing the parameter region where coexistence of the three morphs is possible in a rock-paper-scissors game. Copyright © 2017 Elsevier Ltd. All rights reserved.

Design and Fabrication of a Composite Morphing Radiator Panel Using High Conductivity Fibers

NASA Technical Reports Server (NTRS)

Wescott, Matthew T.; McQuien, J. Scott; Bertagne, Christopher L.; Whitcomb, John D.; Hart, Darren J.; Erickson, Lisa R.

2017-01-01

Upcoming crewed space missions will involve large internal and external heat loads and require advanced thermal control systems to maintain a desired internal environment temperature. Radiators with at least 12:1 turndown ratios (the ratio between the maximum and minimum heat rejection rates) will be needed. However, current technologies are only able to achieve turndown ratios of approximately 3:1. A morphing radiator capable of altering shape could significantly increase turndown capabilities. Shape memory alloys offer qualities that may be well suited for this endeavor; their temperature-dependent phase changes could offer radiators the ability to passively control heat rejection. In 2015, a morphing radiator prototype was constructed and tested in a thermal vacuum environment, where it successfully demonstrated the morphing behavior and variable heat rejection. Newer composite prototypes have since been designed and manufactured using two distinct types of SMA materials. These models underwent temperature cycling tests in a thermal vacuum chamber and a series of fatigue tests to characterize the lifespan of these designs. The focus of this paper is to present the design approach and testing of the morphing composite facesheet. The discussion includes: an overall description of the project background, definition of performance requirements, composite materials selection, use of analytic and numerical design tools, facesheet fabrication, and finally fatigue testing with accompanying results.

Querying clinical data in HL7 RIM based relational model with morph-RDB.

PubMed

Priyatna, Freddy; Alonso-Calvo, Raul; Paraiso-Medina, Sergio; Corcho, Oscar

2017-10-05

Semantic interoperability is essential when carrying out post-genomic clinical trials where several institutions collaborate, since researchers and developers need to have an integrated view and access to heterogeneous data sources. One possible approach to accommodate this need is to use RDB2RDF systems that provide RDF datasets as the unified view. These RDF datasets may be materialized and stored in a triple store, or transformed into RDF in real time, as virtual RDF data sources. Our previous efforts involved materialized RDF datasets, hence losing data freshness. In this paper we present a solution that uses an ontology based on the HL7 v3 Reference Information Model and a set of R2RML mappings that relate this ontology to an underlying relational database implementation, and where morph-RDB is used to expose a virtual, non-materialized SPARQL endpoint over the data. By applying a set of optimization techniques on the SPARQL-to-SQL query translation algorithm, we can now issue SPARQL queries to the underlying relational data with generally acceptable performance.

Multigrid optimal mass transport for image registration and morphing

NASA Astrophysics Data System (ADS)

Rehman, Tauseef ur; Tannenbaum, Allen

2007-02-01

In this paper we present a computationally efficient Optimal Mass Transport algorithm. This method is based on the Monge-Kantorovich theory and is used for computing elastic registration and warping maps in image registration and morphing applications. This is a parameter free method which utilizes all of the grayscale data in an image pair in a symmetric fashion. No landmarks need to be specified for correspondence. In our work, we demonstrate significant improvement in computation time when our algorithm is applied as compared to the originally proposed method by Haker et al [1]. The original algorithm was based on a gradient descent method for removing the curl from an initial mass preserving map regarded as 2D vector field. This involves inverting the Laplacian in each iteration which is now computed using full multigrid technique resulting in an improvement in computational time by a factor of two. Greater improvement is achieved by decimating the curl in a multi-resolutional framework. The algorithm was applied to 2D short axis cardiac MRI images and brain MRI images for testing and comparison.

LIMITED-USE CHEMICAL PROTECTIVE CLOTHING FOR EPA SUPERFUND ACTIVITIES

EPA Science Inventory

Because contractor field personnel complained about the poor durability and fit of limited-use chemical protective clothing (CPC) most commonly used at hazardous waste site operations, the U.S. Environmental Protection Agency (EPA) initiated a study to characterize use of CPC; de...

LIMITED-USE CHEMICAL PROTECTIVE CLOTHING FOR EPA SUPERFUND ACTIVITIES

EPA Science Inventory

Because contractor field personnel complained about the poor durability and fit of limited-use chemical protective clothing (CPC) most commonly used at hazardous waste site operations, the U.S. Environmental Protection Agency (EPA) initiated a study to • characterize use of CPC...

Long-term efficacy of a 0.07% cetylpyridinium chloride mouth rinse in relation to plaque and gingivitis: a 6-month randomized, vehicle-controlled clinical trial.

PubMed

Van Leeuwen, M P C; Rosema, N A M; Versteeg, P A; Slot, D E; Van Winkelhoff, A J; Van der Weijden, G A

2015-05-01

To evaluate the effectiveness of 0.07% cetylpyridinium chloride (CPC) mouth rinse for reduction of gingival inflammation and inhibition of plaque compared to a vehicle control (VC) mouth rinse over a 6-month period. Participants (n = 62) used their randomly assigned product as adjunct to toothbrushing. Bleeding, plaque and staining scores were assessed at baseline, 3 and 6 months. Plaque and saliva samples were taken at each assessment monitoring possible shifts in the composition of the microbiota. A significant difference (P = 0.002) in favour of the CPC mouth rinse, with respect to plaque scores, was found. Bleeding scores at 6 months were not significantly different (P = 0.089). However, when correcting for baseline values, a tendency towards a significant difference in bleeding scores at end trail was observed in favour of the CPC mouth rinse (P = 0.061). Regarding staining at 3 and 6 months, a small but significant difference (8.6% and 10.4%, respectively) (P < 0.0001) was observed with lower scores for the VC group. There was a significant reduction in total anaerobic count in the CPC group at 6 months (P < 0.05). The ratio of aerobes/anaerobes was markedly increased at 3 months, especially in the CPC group. No further differences were observed between groups at 6 months. The use of 0.07% CPC mouth rinse was significantly more effective in reducing plaque scores than the vehicle control. Bleeding scores were not different at 6 months. The test product was well accepted and did not cause any serious clinical side effects or negatively affected the microbiota. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Rejuvenation of human cardiac progenitor cells with Pim-1 kinase.

PubMed

Mohsin, Sadia; Khan, Mohsin; Nguyen, Jonathan; Alkatib, Monique; Siddiqi, Sailay; Hariharan, Nirmala; Wallach, Kathleen; Monsanto, Megan; Gude, Natalie; Dembitsky, Walter; Sussman, Mark A

2013-10-25

Myocardial function is enhanced by adoptive transfer of human cardiac progenitor cells (hCPCs) into a pathologically challenged heart. However, advanced age, comorbidities, and myocardial injury in patients with heart failure constrain the proliferation, survival, and regenerative capacity of hCPCs. Rejuvenation of senescent hCPCs will improve the outcome of regenerative therapy for a substantial patient population possessing functionally impaired stem cells. Reverse phenotypic and functional senescence of hCPCs by ex vivo modification with Pim-1. C-kit-positive hCPCs were isolated from heart biopsy samples of patients undergoing left ventricular assist device implantation. Growth kinetics, telomere lengths, and expression of cell cycle regulators showed significant variation between hCPC isolated from multiple patients. Telomere length was significantly decreased in hCPC with slow-growth kinetics concomitant with decreased proliferation and upregulation of senescent markers compared with hCPC with fast-growth kinetics. Desirable youthful characteristics were conferred on hCPCs by genetic modification using Pim-1 kinase, including increases in proliferation, telomere length, survival, and decreased expression of senescence markers. Senescence characteristics of hCPCs are ameliorated by Pim-1 kinase resulting in rejuvenation of phenotypic and functional properties. hCPCs show improved cellular properties resulting from Pim-1 modification, but benefits were more pronounced in hCPC with slow-growth kinetics relative to hCPC with fast-growth kinetics. With the majority of patients with heart failure presenting advanced age, infirmity, and impaired regenerative capacity, the use of Pim-1 modification should be incorporated into cell-based therapeutic approaches to broaden inclusion criteria and address limitations associated with the senescent phenotype of aged hCPC.

Rejuvenation of Human Cardiac Progenitor Cells With Pim-1 Kinase

PubMed Central

Mohsin, Sadia; Khan, Mohsin; Nguyen, Jonathan; Alkatib, Monique; Siddiqi, Sailay; Hariharan, Nirmala; Wallach, Kathleen; Monsanto, Megan; Gude, Natalie; Dembitsky, Walter; Sussman, Mark A.

2014-01-01

Rationale Myocardial function is enhanced by adoptive transfer of human cardiac progenitor cells (hCPCs) into a pathologically challenged heart. However, advanced age, comorbidities, and myocardial injury in patients with heart failure constrain the proliferation, survival, and regenerative capacity of hCPCs. Rejuvenation of senescent hCPCs will improve the outcome of regenerative therapy for a substantial patient population possessing functionally impaired stem cells. Objective Reverse phenotypic and functional senescence of hCPCs by ex vivo modification with Pim-1. Methods and Results C-kit–positive hCPCs were isolated from heart biopsy samples of patients undergoing left ventricular assist device implantation. Growth kinetics, telomere lengths, and expression of cell cycle regulators showed significant variation between hCPC isolated from multiple patients. Telomere length was significantly decreased in hCPC with slow-growth kinetics concomitant with decreased proliferation and upregulation of senescent markers compared with hCPC with fast-growth kinetics. Desirable youthful characteristics were conferred on hCPCs by genetic modification using Pim-1 kinase, including increases in proliferation, telomere length, survival, and decreased expression of senescence markers. Conclusions Senescence characteristics of hCPCs are ameliorated by Pim-1 kinase resulting in rejuvenation of phenotypic and functional properties. hCPCs show improved cellular properties resulting from Pim-1 modification, but benefits were more pronounced in hCPC with slow-growth kinetics relative to hCPC with fast-growth kinetics. With the majority of patients with heart failure presenting advanced age, infirmity, and impaired regenerative capacity, the use of Pim-1 modification should be incorporated into cell-based therapeutic approaches to broaden inclusion criteria and address limitations associated with the senescent phenotype of aged hCPC. PMID:24044948

Design and Evaluation of a Personal Diffusion Battery.

PubMed

Vosburgh, Donna J H; Klein, Timothy; Sheehan, Maura; Anthony, T Renee; Peters, Thomas M

A four-stage personal diffusion battery (pDB) was designed and constructed to measure submicron particle size distributions. The pDB consisted of a screen-type diffusion battery, solenoid valve system, and electronic controller. A data inversion spreadsheet was created to solve for the number median diameter (NMD), geometric standard deviation (GSD), and particle number concentration of unimodal aerosols using stage number concentrations from the pDB combined with a handheld condensation particle counter (pDB+CPC). The inversion spreadsheet included particle entry losses, theoretical penetrations across screens, the detection efficiency of the CPC, and constraints so the spreadsheet solved to values within the pDB range. Size distribution parameters (NMD, GSD, and number concentration) measured with the pDB+CPC with inversion spreadsheet were within 25% of those measured with a scanning mobility particle sizer (SMPS) for 5 of 12 polydisperse combustion aerosols. For three tests conducted with propylene torch exhaust, the pDB+CPC with inversion spreadsheet successfully identified that the NMD was smaller than the constraint value of 16 nm. The ratio of the nanoparticle portion of the aerosol compared to the reference ( R nano ) was calculated to determine the ability of pDB+CPC with inversion spreadsheet to measure the nanoparticle portion of the aerosols. The R nano ranged from 0.87 to 1.01 when the inversion solved and from 0.06 to 2.01 when the inversion solved to a constraint. The pDB combined with CPC has limited use as a personal monitor but combining the pDB with a different detector would allow for the pDB to be used as a personal monitor.

Design and Evaluation of a Personal Diffusion Battery

PubMed Central

Vosburgh, Donna J. H.; Klein, Timothy; Sheehan, Maura; Anthony, T. Renee; Peters, Thomas M.

2016-01-01

A four-stage personal diffusion battery (pDB) was designed and constructed to measure submicron particle size distributions. The pDB consisted of a screen-type diffusion battery, solenoid valve system, and electronic controller. A data inversion spreadsheet was created to solve for the number median diameter (NMD), geometric standard deviation (GSD), and particle number concentration of unimodal aerosols using stage number concentrations from the pDB combined with a handheld condensation particle counter (pDB+CPC). The inversion spreadsheet included particle entry losses, theoretical penetrations across screens, the detection efficiency of the CPC, and constraints so the spreadsheet solved to values within the pDB range. Size distribution parameters (NMD, GSD, and number concentration) measured with the pDB+CPC with inversion spreadsheet were within 25% of those measured with a scanning mobility particle sizer (SMPS) for 5 of 12 polydisperse combustion aerosols. For three tests conducted with propylene torch exhaust, the pDB+CPC with inversion spreadsheet successfully identified that the NMD was smaller than the constraint value of 16 nm. The ratio of the nanoparticle portion of the aerosol compared to the reference (R nano) was calculated to determine the ability of pDB+CPC with inversion spreadsheet to measure the nanoparticle portion of the aerosols. The R nano ranged from 0.87 to 1.01 when the inversion solved and from 0.06 to 2.01 when the inversion solved to a constraint. The pDB combined with CPC has limited use as a personal monitor but combining the pDB with a different detector would allow for the pDB to be used as a personal monitor. PMID:26900207

Comparison of plating media for recovery of total and virulent genotypes of Vibrio vulnificus in U.S. market oysters.

PubMed

Jones, Jessica L; Lüdeke, Catharina H M; Bowers, John C; DePaola, Angelo

2013-11-01

Vibrio vulnificus is the leading cause of seafood associated mortality in the United States and is generally associated with consumption of raw oysters. Two genetic markers have emerged as indicators of strain virulence, 16S rDNA type B (rrnB) and virulence correlated gene type C (vcgC). While much is known about the distribution of V. vulnificus in oysters, a limited number of studies have addressed the more virulent subtypes. Therefore, the goals of this study were to (1) determine the suitability of media for recovery of total and virulent genotypes of V. vulnificus and (2) evaluate the geographical and seasonal distribution of these genotypes. Market oysters from across the United States and the strains isolated from them during a year-long study in 2007 were used. For media evaluation, VVA and CPC+ were compared using direct plating of oyster tissues while mCPC and CPC+ were compared for isolation following MPN enrichment. Representative isolates from each media/method were tested for rrn and vcg types to determine their seasonal and geographical distribution. No statistically significant difference was observed between VVA/CPC+ or mCPC/CPC+ for isolation of total or virulent (rrnB/vcgC) genotypes of V. vulnificus. Overall, 32% of recovered isolates possessed the virulent genotype. The prevalence of these genotypes was highest in oysters from the Gulf Coast during Oct-Dec, and demonstrated a statistically significant geographical and seasonal pattern. This is the first report on the distribution of virulent V. vulnificus genotypes across the United States, which provides novel insight into the occurrence of this pathogen. © 2013.

Relationship Between the Duration of Cardiopulmonary Resuscitation and Favorable Neurological Outcomes After Out-of-Hospital Cardiac Arrest: A Prospective, Nationwide, Population-Based Cohort Study.

PubMed

Goto, Yoshikazu; Funada, Akira; Goto, Yumiko

2016-03-18

The determination of appropriate duration of in-the-field cardiopulmonary resuscitation (CPR) for out-of-hospital cardiac arrest (OHCA) patients is one of the biggest challenges for emergency medical service providers and clinicians. The appropriate CPR duration before termination of resuscitation remains unclear and may differ based on initial rhythm. We aimed to determine the relationship between CPR duration and post-OHCA outcomes. We analyzed the records of 17 238 OHCA patients (age ≥18 years) who achieved prehospital return of spontaneous circulation. Data were prospectively recorded in a nationwide, Japanese database between 2011 and 2012. The time from CPR initiation to prehospital return of spontaneous circulation (CPR duration) was calculated. The primary end point was 1-month survival with favorable neurological outcomes (Cerebral Performance Category [CPC] scale; CPC 1-2). The 1-month CPC 1-2 rate was 21.8% (n=3771). CPR duration was inversely associated with 1-month CPC 1-2 (adjusted unit odds ratio: 0.95, 95% CI: 0.94-0.95). Among all patients, a cumulative proportion of >99% of 1-month CPC 1-2 was achieved with a CPR duration of 35 minutes. When sorted by the initial rhythm, the CPR duration producing more than 99% of survivors with CPC 1-2 was 35 minutes for shockable rhythms and pulseless electrical activity, and 42 minutes for asystole. CPR duration was independently and inversely associated with favorable 1-month neurological outcomes. The critical prehospital CPR duration for OHCA was 35 minutes in patients with initial shockable rhythms and pulseless electrical activity, and 42 minutes in those with initial asystole. © 2016 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Study of pelvic floor and sphincter muscles in congenital pouch colon with the help of three-dimensional CT scan.

PubMed

Maletha, Madhukar; Kureel, S N; Khan, Tanvir Roshan; Wakhlu, Ashish

2010-12-01

Congenital pouch colon (CPC) is a pouch-like dilatation of shortened colon associated with anorectal malformation (ARM). The disease is prevalent in northern India. Postoperatively, the continence results are not as good as in other ARMs and there is higher incidence of incontinence and perineal soiling in these patients. The present study aimed to evaluate the pelvic floor and sphincter muscle characteristics in patients of CPC with the help of 64-slice computerized tomography with three-dimensional (3D) volumetric reconstructions of images, thus, to know the overall quality of these muscles in the patients. The study was conducted in patients admitted over a period of July 2007 to November 2008 in our department. Totally, eight patients of CPC were subjected to 64-slice CT with three-dimensional reconstructions of images and different parameters such as quality of pelvic floor muscles, configuration of vertical and parasagittal fibres, shape and thickness of sphincter muscle complex, attenuation values of sphincters were studied. The 3D reconstructed images of pelvis in patients of CPC showed a well-developed pelvic floor and sphincter muscle complex. The length of the parasagittal fibres, transverse width of the vertical fibres and CT attenuation values of these structures with overall muscle quality were found to be good in these patients. In cases of CPC, the pelvic floor muscles including striated muscle complex (vertical and parasagittal fibres) are well developed. Higher rates of incontinence and soiling in CPC are not because of poorly developed pelvic floor and sphincter muscles. Three-dimensional CT can also provide important anatomical information that can help the operating surgeon while performing surgery.

Characterization of three new condensation particle counters for sub-3 nm particle detection during the Helsinki CPC workshop: the ADI versatile water CPC, TSI 3777 nano enhancer and boosted TSI 3010

NASA Astrophysics Data System (ADS)

Kangasluoma, Juha; Hering, Susanne; Picard, David; Lewis, Gregory; Enroth, Joonas; Korhonen, Frans; Kulmala, Markku; Sellegri, Karine; Attoui, Michel; Petäjä, Tuukka

2017-06-01

In this study we characterized the performance of three new particle counters able to detect particles smaller than 3 nm during the Helsinki condensation particle counter (CPC) workshop in summer 2016: the Aerosol Dynamics Inc. (ADI; Berkeley, USA) versatile water condensation particle counter (vWCPC), TSI 3777 nano enhancer (TSI Inc., Shoreview, USA) and modified and boosted TSI 3010-type CPC from Université Blaise Pascal called a B3010. The performance of all CPCs was first measured with charged tungsten oxide test particles at temperature settings which resulted in supersaturation low enough to not detect any ions produced by a radioactive source. Due to similar measured detection efficiencies, additional comparison between the 3777 and vWCPC were conducted using electrically neutral tungsten oxide test particles and with positively charged tetradodecylammonium bromide. Furthermore, the detection efficiencies of the 3777 and vWCPC were measured with boosted temperature settings yielding supersaturation which was at the onset of homogeneous nucleation for the 3777 or confined within the range of liquid water for the ADI vWCPC. Finally, CPC-specific tests were conducted to probe the response of the 3777 to various inlet flow relative humidities, of the B3010 to various inlet flow rates and of the vWCPC to various particle concentrations. For the 3777 and vWCPC the measured 50 % detection diameters (d50s) were in the range of 1.3-2.4 nm for the tungsten oxide particles, depending on the particle charging state and CPC temperature settings, between 2.5 and 3.3 nm for the organic test aerosol, and in the range of 3.2-3.4 nm for tungsten oxide for the B3010.

Production of the α and β Subunits of Spirulina Allophycocyanin and C-Phycocyanin in Escherichia coli : A Comparative Study of Their Antioxidant Activities.

PubMed

Cherdkiatikul, Thiti; Suwanwong, Yaneenart

2014-07-01

Allophycocyanin and c-phycocyanin have been reported to be potent antioxidants. In this work, the genes encoding the apo-proteins of allophycocyanin α (ApcA), allophycocyanin β (ApcB), c-phycocyanin α (CpcA), and c-phycocyanin β (CpcB) from Spirulina platensis were cloned, and the recombinant proteins were produced in Escherichia coli to study their antioxidant effects. All four recombinant phycocyanins could be produced in the soluble form and purified to more than 97% purity. The results of radical scavenging assays showed that the Trolox equivalent values for peroxyl radical scavenging by the ApcA, ApcB, CpcA, and CpcB proteins were 1.81 ± 0.2 µM, 1.98 ± 0.22 µM, 0.95 ± 0.15 µM, and 1.49 ± 0.15 µM, respectively. The IC50 values for hydroxyl radical scavenging of ApcA, ApcB, CpcA, CpcB, and Trolox were 269 ± 9 µg/mL, 190 ± 5 µg/mL, 129 ± 8 µg/mL, 108 ± 4 µg/mL, and 195 ± 12 µg/mL, respectively. These results indicated that allophycocyanin exhibited higher activity than c-phycocyanin in scavenging peroxyl radicals, whereas c-phycocyanin exhibited higher activity than allophycocyanin in scavenging hydroxyl radicals. All of the apo-phycocyanin subunits possessed strong antioxidant activities and can be further developed and applied to the food and drug industries. However, the selection of the most useful antioxidant should depend on the type of targeted free radical to obtain the highest efficiency. © 2014 Society for Laboratory Automation and Screening.

A high-throughput microfluidic dental plaque biofilm system to visualize and quantify the effect of antimicrobials

PubMed Central

Nance, William C.; Dowd, Scot E.; Samarian, Derek; Chludzinski, Jeffrey; Delli, Joseph; Battista, John; Rickard, Alexander H.

2013-01-01

Objectives Few model systems are amenable to developing multi-species biofilms in parallel under environmentally germane conditions. This is a problem when evaluating the potential real-world effectiveness of antimicrobials in the laboratory. One such antimicrobial is cetylpyridinium chloride (CPC), which is used in numerous over-the-counter oral healthcare products. The aim of this work was to develop a high-throughput microfluidic system that is combined with a confocal laser scanning microscope (CLSM) to quantitatively evaluate the effectiveness of CPC against oral multi-species biofilms grown in human saliva. Methods Twenty-four-channel BioFlux microfluidic plates were inoculated with pooled human saliva and fed filter-sterilized saliva for 20 h at 37°C. The bacterial diversity of the biofilms was evaluated by bacterial tag-encoded FLX amplicon pyrosequencing (bTEFAP). The antimicrobial/anti-biofilm effect of CPC (0.5%–0.001% w/v) was examined using Live/Dead stain, CLSM and 3D imaging software. Results The analysis of biofilms by bTEFAP demonstrated that they contained genera typically found in human dental plaque. These included Aggregatibacter, Fusobacterium, Neisseria, Porphyromonas, Streptococcus and Veillonella. Using Live/Dead stain, clear gradations in killing were observed when the biofilms were treated with CPC between 0.5% and 0.001% w/v. At 0.5% (w/v) CPC, 90% of the total signal was from dead/damaged cells. Below this concentration range, less killing was observed. In the 0.5%–0.05% (w/v) range CPC penetration/killing was greatest and biofilm thickness was significantly reduced. Conclusions This work demonstrates the utility of a high-throughput microfluidic–CLSM system to grow multi-species oral biofilms, which are compositionally similar to naturally occurring biofilms, to assess the effectiveness of antimicrobials. PMID:23800904

The Use of Platelets to Affect Functional Healing of an Anterior Cruciate Ligament (ACL) Autograft in a Caprine ACL Reconstruction Model

PubMed Central

Spindler, Kurt P.; Murray, Martha M.; Carey, James L.; Zurakowski, David; Fleming, Braden C.

2009-01-01

Many anterior cruciate ligament (ACL) reconstructions have increased laxity postoperatively. We hypothesized that enhancing an ACL graft with a collagen-platelet composite (CPC) would improve knee laxity and graft structural properties. We also hypothesized the platelet concentration in the CPC would affect these parameters. Twelve goats underwent ACL reconstruction with autologous patellar tendon graft. In six goats, a collagen-platelet composite was placed around the graft (CPC group). In the remaining six goats, the collagen scaffold only was used (COLL group). Three goats were excluded due to complications. After 6 weeks in vivo, anterior–posterior (AP) laxity and tensile properties of the ACL reconstructed knees were measured and normalized against the contralateral intact knee. At a knee flexion angle of 30°, the average increase in AP laxity was 40% less in the CPC group than the COLL group (p = 0.045). At 60°, the AP laxity was 30% less in the CPC group, a difference that was close to statistical significance (p = 0.080). No differences were found between treatment groups with respect to the structural properties (p > 0.30). However, there were significant correlations between serum platelet concentration and AP laxity (R2 = 0.643; p = 0.009), maximum load (R2 = 0.691; p = 0.006), and graft stiffness (R2 = 0.840; p < 0.001). In conclusion, use of a CPC to enhance healing of an allograft ACL reconstruction inversely correlated with early sagittal plane laxity and the systemic platelet count was highly predictive of ACL reconstruction graft strength and stiffness at 6 weeks. These findings emphasize the importance of further research on delineating the effect of platelets in treating of ACL injuries. PMID:19009602

E-Science technologies in a workflow for personalized medicine using cancer screening as a case study.

PubMed

Spjuth, Ola; Karlsson, Andreas; Clements, Mark; Humphreys, Keith; Ivansson, Emma; Dowling, Jim; Eklund, Martin; Jauhiainen, Alexandra; Czene, Kamila; Grönberg, Henrik; Sparén, Pär; Wiklund, Fredrik; Cheddad, Abbas; Pálsdóttir, Þorgerður; Rantalainen, Mattias; Abrahamsson, Linda; Laure, Erwin; Litton, Jan-Eric; Palmgren, Juni

2017-09-01

We provide an e-Science perspective on the workflow from risk factor discovery and classification of disease to evaluation of personalized intervention programs. As case studies, we use personalized prostate and breast cancer screenings. We describe an e-Science initiative in Sweden, e-Science for Cancer Prevention and Control (eCPC), which supports biomarker discovery and offers decision support for personalized intervention strategies. The generic eCPC contribution is a workflow with 4 nodes applied iteratively, and the concept of e-Science signifies systematic use of tools from the mathematical, statistical, data, and computer sciences. The eCPC workflow is illustrated through 2 case studies. For prostate cancer, an in-house personalized screening tool, the Stockholm-3 model (S3M), is presented as an alternative to prostate-specific antigen testing alone. S3M is evaluated in a trial setting and plans for rollout in the population are discussed. For breast cancer, new biomarkers based on breast density and molecular profiles are developed and the US multicenter Women Informed to Screen Depending on Measures (WISDOM) trial is referred to for evaluation. While current eCPC data management uses a traditional data warehouse model, we discuss eCPC-developed features of a coherent data integration platform. E-Science tools are a key part of an evidence-based process for personalized medicine. This paper provides a structured workflow from data and models to evaluation of new personalized intervention strategies. The importance of multidisciplinary collaboration is emphasized. Importantly, the generic concepts of the suggested eCPC workflow are transferrable to other disease domains, although each disease will require tailored solutions. © The Author 2017. Published by Oxford University Press on behalf of the American Medical Informatics Association.

Acute effect of different concentrations of cayenne pepper cataplasm on sensory-motor functions and serum levels of inflammation-related biomarkers in healthy subjects.

PubMed

Sarabon, Nejc; Löfler, Stefan; Cvecka, Jan; Hübl, Wolfgang; Zampieri, Sandra

2018-01-12

Physical medicine therapies are often used in treating widespread musculoskeletal disorders, such as neck and low back pain. Herbal cataplasms containing rubefacient substances, such as Cayenne pepper, or galenic preparations like Munari cataplasm are commonly used as natural medications to treat painful areas. In this paper we show the effects of a 20-min application of Cayenne pepper and kaolin powder cataplasm (CPC) on healthy subjects. Treatment effects were evaluated by cold/hot feeling on visual analogue scale, blood pressure, body temperature, skin light touch sensations, two-point discrimination, and pain threshold to a mechanical stimulus, before and immediately after, 15 min after and 30 min after different concentration of Cayenne pepper in CPC preparation on healthy subjects. Maximal voluntary trunk extension force and trunk extension submaximal force matching error were also measured. In addition, the resulting optimal CPC mixture was tested for its safety by measuring changes in circulating levels of inflammatory-related biomarkers after 20-min application. The results indicate that the 5% concentration of Cayenne pepper in the preparation of CPC is the best choice, since no additional effects can be obtained with the 10% concentration, and the effects are higher than those observed at the 2.5% concentration. Importantly, 5% CPC application did not induce a significant increase of inflammatory-related biomarkers, suggesting that 20-min application has no negative side effects at systemic levels. Further studies are needed to investigate the immediate and long-term effects of repeated CPC applications as well as to understand the intersecting underlying mechanisms activated by Capsaicin and other identified factors, in order to be more extensively used in the field of physical medicine therapies.

Life-history evolution and the microevolution of intermediary metabolism: activities of lipid-metabolizing enzymes in life-history morphs of a wing-dimorphic cricket.

PubMed

Zera, Anthony J; Zhao, Zhangwu

2003-03-01

Although a considerable amount of information is available on the ecology, genetics, and physiology of life-history traits, much more limited data are available on the biochemical and genetic correlates of life-history variation within species. Specific activities of five enzymes of lipid biosynthesis and two enzymes of amino acid catabolism were compared among lines selected for flight-capable (LW[f]) versus flightless (SW) morphs of the cricket Gryllus firmus. These morphs, which exist in natural populations, differ genetically in ovarian growth (100-400% higher in SW) and aspects of flight capability including the size of wings and flight muscles, and the concentration of triglyceride flight fuel (40% greater in LW[f]). Consistently higher activity of each enzyme in LW(f) versus SW-selected lines, and strong co-segregation between morph and enzyme activity, demonstrated genetically based co-variance between wing morph and enzyme activity. Developmental profiles of enzyme activities strongly paralleled profiles of triglyceride accumulation during adulthood and previous measures of in vivo lipid biosynthesis. These data strongly imply that genetically based elevation in activities of lipogenic enzymes, and enzymes controlling the conversion of amino acids into lipids, is an important cause underlying the elevated accumulation of triglyceride in the LW(f) morph, a key biochemical component of the trade-off between elevated early fecundity and flight capability. Global changes in lipid and amino-acid metabolism appear to have resulted from microevolutionary alteration of regulators of metabolism. Finally, strong genotype x environment (diet) interactions were observed for most enzyme activities. Future progress in understanding the functional causes of life-history evolution requires a more detailed synthesis of the fields of life-history evolution and metabolic biochemistry. Wing polymorphism is a powerful experimental model in such integrative studies.

Balancing selection maintains cryptic colour morphs.

PubMed

Wellenreuther, Maren

2017-11-01

Animals display incredibly diverse colour patterns, a testament to evolution's endless innovation in shaping life. In many species, the interplay between males and females in the pursuit of mates has driven the evolution of a myriad of colour forms, from the flashy peacock tail feathers to the tiniest colour markings in damselflies. In others, colour provides crypsis by allowing to blend into the background and to escape the eyes of predators. While the obvious benefits of this dazzling diversity for reproduction and survival seem straightforward, its maintenance is not. Theory predicts that genetic drift and various forms of selection reduce variation over time, making the persistence of colour variants over generations a puzzle. In this issue of Molecular Ecology, Lindtke et al. () study the cryptic colour morphs of Timema cristinae walking sticks to shed light on the genetic architecture and mechanisms that allow colour polymorphism maintenance over long timescales. By combining genome-wide data with phenotyping information from natural populations, they were able to map the green and melanistic colour to one genomic region with highly reduced effective recombination rate between two main chromosomal variants, consistent with an inversion polymorphism. These two main chromosomal variants showed geographically widespread heterozygote excess, and genomic signatures consistent with long-term balancing selection. A younger chromosomal variant was detected for the third morph, the green-striped colour morphs, in the same genomic regions as the melanistic and the green-unstriped morphs. Together, these results suggest that the genetic architecture of cryptic T. cristinae morphs is caused by nonrecombining genomic blocks that have been maintained over extended time periods by balancing selection making this study one of the few available empirical examples documenting that balancing selection of various forms may play an important role in maintaining adaptive genetic variation in nature. © 2017 John Wiley & Sons Ltd.

Genetic mapping of the female mimic morph locus in the ruff

PubMed Central

2013-01-01

Background Ruffs (Aves: Philomachus pugnax) possess a genetic polymorphism for male mating behaviour resulting in three permanent alternative male reproductive morphs: (i) territorial ‘Independents’, (ii) non-territorial ‘Satellites’, and (iii) female-mimicking ‘Faeders’. Development into independent or satellite morphs has previously been shown to be due to a single-locus, two-allele autosomal Mendelian mode of inheritance at the Satellite locus. Here, we use linkage analysis to map the chromosomal location of the Faeder locus, which controls development into the Faeder morph, and draw further conclusions about candidate genes, assuming shared synteny with other birds. Results Segregation data on the Faeder locus were obtained from captive-bred pedigrees comprising 64 multi-generation families (N = 381). There was no evidence that the Faeder locus was linked to the Satellite locus, but it was linked with microsatellite marker Ppu020. Comparative mapping of ruff microsatellite markers against the chicken (Gallus gallus) and zebra finch (Taeniopygia guttata) genomes places the Ppu020 and Faeder loci on a region of chromosome 11 that includes the Melanocortin-1 receptor (MC1R) gene, which regulates colour polymorphisms in numerous birds and other vertebrates. Melanin-based colouration varies with life-history strategies in ruffs and other species, thus the MC1R gene is a strong candidate to play a role in alternative male morph determination. Conclusion Two unlinked loci appear to control behavioural development in ruffs. The Faeder locus is linked to Ppu020, which, assuming synteny, is located on avian chromosome 11. MC1R is a candidate gene involved in alternative male morph determination in ruffs. PMID:24256185

An allelic series at pax7a is associated with colour polymorphism diversity in Lake Malawi cichlid fish.

PubMed

Roberts, Reade B; Moore, Emily C; Kocher, Thomas D

2017-05-01

Despite long-standing interest in the evolution and maintenance of discrete phenotypic polymorphisms, the molecular genetic basis of such polymorphism in the wild is largely unknown. Female sex-associated blotched colour polymorphisms found in cichlids of Lake Malawi, East Africa, represent a highly successful polymorphic phenotype, found and maintained in four genera across the geographic expanse of the lake. Previously, we identified an association with an allelic variant of the paired-box transcription factor gene pax7a and blotched colour morphs in Lake Malawi cichlid fishes. Although a diverse range of blotched phenotypes are present in Lake Malawi cichlid species, they all appeared to result from an allele of pax7a that produces increased levels of transcript. Here, we examine the developmental and genetic basis of variation among blotched morphs. First, we confirm that pax7a-associated blotch morphs result primarily from modulation of melanophore development and survival. From laboratory crosses and natural population studies, we identify at least three alleles of pax7a associated with discrete subtypes of blotched morphs, in addition to the ancestral pax7a allele. Genotypes at pax7a support initial evolution of a novel pax7a allele to produce the blotched class of morphs, followed by subsequent evolution of that pax7a blotched allele to produce additional alleles associated with discrete colour morphs. Variant alleles of pax7a produce different levels of pax7a transcript, correlating with pigmentation phenotype at the cellular level. This naturally selected allelic series should serve as a case study for understanding the molecular genetic control of pax7a expression and the evolution of sex-associated alleles. © 2016 John Wiley & Sons Ltd.

National Centers for Environmental Prediction

Science.gov Websites

/ VISION | About EMC EMC > GEFS > COLLABORATORS Home Operational Products Experimental Data ENSEMBLE FORECAST SYSTEM MSC NAEFS Products CPC NAEFS Experimental 8 to 14 Day Temperature Guidance CPC NAEFS Experimental 8 to 14 Day Precip Guidance NOAA / National Weather Service National Centers for

TD-60 links RalA GTPase function to the CPC in mitosis

PubMed Central

Papini, Diana; Langemeyer, Lars; Abad, Maria A.; Kerr, Alastair; Samejima, Itaru; Eyers, Patrick A.; Jeyaprakash, A. Arockia; Higgins, Jonathan M. G.; Barr, Francis A.; Earnshaw, William C.

2015-01-01

TD-60 (also known as RCC2) is a highly conserved protein that structurally resembles the Ran guanine exchange factor (GEF) RCC1, but has not previously been shown to have GEF activity. TD-60 has a typical chromosomal passenger complex (CPC) distribution in mitotic cells, but associates with integrin complexes and is involved in cell motility during interphase. Here we show that TD-60 exhibits GEF activity, in vitro and in cells, for the small GTPase RalA. TD-60 or RalA depletion causes spindle abnormalities in prometaphase associated with abnormal centromeric accumulation of CPC components. TD-60 and RalA apparently work together to contribute to the regulation of kinetochore–microtubule interactions in early mitosis. Importantly, several mitotic phenotypes caused by TD-60 depletion are reverted by the expression of a GTP-locked mutant, RalA (Q72L). The demonstration that a small GTPase participates in the regulation of the CPC reveals a level of mitotic regulation not suspected in previous studies. PMID:26158537

Taste bud development and patterning in sighted and blind morphs of Astyanax mexicanus.

PubMed

Varatharasan, Nirupa; Croll, Roger P; Franz-Odendaal, Tamara

2009-12-01

In the blind cave-dwelling morph of A. mexicanus, the eye degenerates while other sensory systems, such as gustation, are expanded compared to their sighted (surface-dwelling) ancestor. This study compares the development of taste buds along the jaws of each morph. To determine whether cavefish have an altered onset or rate of taste bud development, we fluorescently labeled basal and receptor cells within taste buds over a developmental series. Our results show that taste bud number increases during development in both morphs. The rate of development is, however, accelerated in cavefish; a small difference in taste bud number exists at 5 dpf reaching threefold by 22 dpf. The expansion of taste buds in cavefish is, therefore, detectable after the onset of eye degeneration. This study provides important insights into the timing of taste bud expansion in cavefish as well as enhances our understanding of taste bud development in teleosts in general. (c) 2009 Wiley-Liss, Inc.

Antibiotic-impregnated calcium phosphate cement as part of a comprehensive treatment for patients with established orthopaedic infection.

PubMed

Niikura, Takahiro; Lee, Sang Yang; Iwakura, Takashi; Sakai, Yoshitada; Kuroda, Ryosuke; Kurosaka, Masahiro

2016-07-01

The treatment of established orthopaedic infection is challenging. While the main focus of treatment is wide surgical debridement, systemic and local antibiotic administration are important adjuvant therapies. Several reports have described the clinical use of antibiotic-impregnated calcium phosphate cement (CPC) to provide local antibiotic therapy for bone infections. However, these were all individual case reports, and no case series have been reported. We report a case series treated by a single surgeon using antibiotic-impregnated CPC as part of a comprehensive treatment plan in patients with established orthopaedic infection. We enrolled 13 consecutive patients with osteomyelitis (n = 6) or infected non-union (n = 7). Implantation of antibiotic-impregnated CPC was performed to provide local antibiotic therapy as part of a comprehensive treatment plan that also included wide surgical debridement, systemic antibiotic therapy, and subsequent second-stage reconstruction surgery. We investigated the rate of successful infection eradication and systemic/local complications. The concentration of antibiotics in the surgical drainage fluids, blood, and recovered CPC (via elution into a phosphate-buffered saline bath) were measured. The mean follow-up period after surgery was 50.4 (range, 27-73) months. There were no cases of infection recurrence during follow-up. No systemic toxicity or local complications from the implantation of antibiotic-impregnated CPC were observed. The vancomycin concentration in the fluid from surgical drainage (n = 6) was 527.1 ± 363.9 μg/mL on postoperative day 1 and 224.5 ± 198.4 μg/mL on postoperative day 2. In patients who did not receive systemic vancomycin therapy (n = 3), the maximum serum vancomycin level was <0.8 μg/mL. In vitro vancomycin elution was observed from the CPC that was surgically retrieved (n = 2). Implantation of antibiotic-impregnated CPC is an option to provide local antibiotic therapy as part of a comprehensive treatment plan. Copyright © 2016 The Japanese Orthopaedic Association. Published by Elsevier B.V. All rights reserved.

Topology synthesis and size optimization of morphing wing structures

NASA Astrophysics Data System (ADS)

Inoyama, Daisaku

This research demonstrates a novel topology and size optimization methodology for synthesis of distributed actuation systems with specific applications to morphing air vehicle structures. The main emphasis is placed on the topology and size optimization problem formulations and the development of computational modeling concepts. The analysis model is developed to meet several important criteria: It must allow a rigid-body displacement, as well as a variation in planform area, with minimum strain on structural members while retaining acceptable numerical stability for finite element analysis. Topology optimization is performed on a semi-ground structure with design variables that control the system configuration. In effect, the optimization process assigns morphing members as "soft" elements, non-morphing load-bearing members as "stiff' elements, and non-existent members as "voids." The optimization process also determines the optimum actuator placement, where each actuator is represented computationally by equal and opposite nodal forces with soft axial stiffness. In addition, the configuration of attachments that connect the morphing structure to a non-morphing structure is determined simultaneously. Several different optimization problem formulations are investigated to understand their potential benefits in solution quality, as well as meaningfulness of the formulations. Extensions and enhancements to the initial concept and problem formulations are made to accommodate multiple-configuration definitions. In addition, the principal issues on the external-load dependency and the reversibility of a design, as well as the appropriate selection of a reference configuration, are addressed in the research. The methodology to control actuator distributions and concentrations is also discussed. Finally, the strategy to transfer the topology solution to the sizing optimization is developed and cross-sectional areas of existent structural members are optimized under applied aerodynamic loads. That is, the optimization process is implemented in sequential order: The actuation system layout is first determined through multi-disciplinary topology optimization process, and then the thickness or cross-sectional area of each existent member is optimized under given constraints and boundary conditions. Sample problems are solved to demonstrate the potential capabilities of the presented methodology. The research demonstrates an innovative structural design procedure from a computational perspective and opens new insights into the potential design requirements and characteristics of morphing structures.

Transcriptional dynamics of a conserved gene expression network associated with craniofacial divergence in Arctic charr.

PubMed

Ahi, Ehsan Pashay; Kapralova, Kalina Hristova; Pálsson, Arnar; Maier, Valerie Helene; Gudbrandsson, Jóhannes; Snorrason, Sigurdur S; Jónsson, Zophonías O; Franzdóttir, Sigrídur Rut

2014-01-01

Understanding the molecular basis of craniofacial variation can provide insights into key developmental mechanisms of adaptive changes and their role in trophic divergence and speciation. Arctic charr (Salvelinus alpinus) is a polymorphic fish species, and, in Lake Thingvallavatn in Iceland, four sympatric morphs have evolved distinct craniofacial structures. We conducted a gene expression study on candidates from a conserved gene coexpression network, focusing on the development of craniofacial elements in embryos of two contrasting Arctic charr morphotypes (benthic and limnetic). Four Arctic charr morphs were studied: one limnetic and two benthic morphs from Lake Thingvallavatn and a limnetic reference aquaculture morph. The presence of morphological differences at developmental stages before the onset of feeding was verified by morphometric analysis. Following up on our previous findings that Mmp2 and Sparc were differentially expressed between morphotypes, we identified a network of genes with conserved coexpression across diverse vertebrate species. A comparative expression study of candidates from this network in developing heads of the four Arctic charr morphs verified the coexpression relationship of these genes and revealed distinct transcriptional dynamics strongly correlated with contrasting craniofacial morphologies (benthic versus limnetic). A literature review and Gene Ontology analysis indicated that a significant proportion of the network genes play a role in extracellular matrix organization and skeletogenesis, and motif enrichment analysis of conserved noncoding regions of network candidates predicted a handful of transcription factors, including Ap1 and Ets2, as potential regulators of the gene network. The expression of Ets2 itself was also found to associate with network gene expression. Genes linked to glucocorticoid signalling were also studied, as both Mmp2 and Sparc are responsive to this pathway. Among those, several transcriptional targets and upstream regulators showed differential expression between the contrasting morphotypes. Interestingly, although selected network genes showed overlapping expression patterns in situ and no morph differences, Timp2 expression patterns differed between morphs. Our comparative study of transcriptional dynamics in divergent craniofacial morphologies of Arctic charr revealed a conserved network of coexpressed genes sharing functional roles in structural morphogenesis. We also implicate transcriptional regulators of the network as targets for future functional studies.

Compound parabolic concentrator optical fiber tip for FRET-based fluorescent sensors

NASA Astrophysics Data System (ADS)

Ul Hassan, Hafeez; Nielsen, Kristian; Aasmul, Soren; Bang, Ole

2015-09-01

The Compound Parabolic Concentrator (CPC) optical fiber tip shape has been proposed for intensity based fluorescent sensors working on the principle of FRET (Förster Resonance Energy Transfer). A simple numerical Zemax model has been used to optimize the CPC tip geometry for a step-index multimode polymer optical fiber for an excitation and emission wavelength of 550 nm and 650nm, respectively. The model suggests an increase of a factor of 1.6 to 4 in the collected fluorescent power for an ideal CPC tip, as compared to the plane-cut fiber tip for fiber lengths between 5 and 45mm.

Radio-telemetric evidence of migration in the gregarious but not the solitary morph of the Mormon cricket (Anabrus simplex: Orthoptera: Tettigoniidae)

NASA Astrophysics Data System (ADS)

Lorch, Patrick D.; Gwynne, D. T.

The Mormon cricket, Anabrus simplex, is one of just a few species of katydids (or bushcrickets, Orthoptera: Tettigoniidae) that, like migratory locusts, appear to have solitary and migratory morphs. Using radio telemetry we studied movements of individuals of two morphs of this flightless species. Individuals within each migratory band had similar rates of movements along similar directional headings whereas solitary individuals moved little and showed little evidence of directionality in movement. Our results also add to other recent radio-telemetry studies showing that flightless insects of 1-2g in mass can be tracked successfully using these methods.

StreaMorph: A Case for Synthesizing Energy-Efficient Adaptive Programs Using High-Level Abstractions

DTIC Science & Technology

2013-08-12

technique when switching from using eight cores to one core. 1. Introduction Real - time streaming of media data is growing in popularity. This includes...both capture and processing of real - time video and audio, and delivery of video and audio from servers; recent usage number shows over 800 million...source of data, when that source is a real - time source, and it is generally not necessary to get ahead of the sink. Even with real - time sources and sinks

Apoptosis-Resistant Cardiac Progenitor Cells Modified With Apurinic/Apyrimidinic Endonuclease/Redox Factor 1 Gene Overexpression Regulate Cardiac Repair After Myocardial Infarction.

PubMed

Aonuma, Tatsuya; Takehara, Naofumi; Maruyama, Keisuke; Kabara, Maki; Matsuki, Motoki; Yamauchi, Atsushi; Kawabe, Jun-Ichi; Hasebe, Naoyuki

2016-08-01

: Overcoming the insufficient survival of cell grafts is an essential objective in cell-based therapy. Apurinic/apyrimidinic endonuclease/redox factor 1 (APE1) promotes cell survival and may enhance the therapeutic effect of engrafted cells. The aim of this study is to determine whether APE1 overexpression in cardiac progenitor cells (CPCs) could ameliorate the efficiency of cell-based therapy. CPCs isolated from 8- to 10-week-old C57BL/6 mouse hearts were infected with retrovirus harboring APE1-DsRed (APE1-CPC) or a DsRed control (control-CPC). Oxidative stress-induced apoptosis was then assessed in APE1-CPCs, control-CPCs, and neonatal rat ventricular myocytes (NRVMs) cocultured with these CPCs. This analysis revealed that APE1 overexpression inhibited CPC apoptosis with activation of transforming growth factor β-activated kinase 1 (TAK1) and nuclear factor (NF)-κB. In the coculture model, NRVM apoptosis was inhibited to a greater extent in the presence of APE1-CPCs compared with control-CPCs. Moreover, the number of surviving DsRed-positive CPC grafts was significantly higher 7 days after the transplant of APE1-CPCs into a mouse myocardial infarction model, and the left ventricular ejection fraction showed greater improvement with attenuation of fibrosis 28 days after the transplant of APE1-CPCs compared with control-CPCs. Additionally, fewer inflammatory macrophages and a higher percentage of cardiac α-sarcomeric actinin-positive CPC-grafts were observed in mice injected with APE1-CPCs compared with control-CPCs after 7 days. In conclusion, antiapoptotic APE1-CPC graft, which increased TAK1-NF-κB pathway activation, survived effectively in the ischemic heart, restored cardiac function, and reduced cardiac inflammation and fibrosis. APE1 overexpression in CPCs may serve as a novel strategy to improve cardiac cell therapy. Improving the survival of cell grafts is essential to maximize the efficacy of cell therapy. The authors investigated the role of APE1 in CPCs under ischemic conditions and evaluated the therapeutic efficacy of transplanted APE1-overexpressing CPCs in a mouse model of myocardial infarction. APE1 hindered apoptosis in CPC grafts subjected to oxidative stress caused in part by increased TAK1-NF-κB pathway activation. Furthermore, APE1-CPC grafts that effectively survived in the ischemic heart restored cardiac function and attenuated fibrosis through pleiotropic mechanisms that remain to be characterized. These findings suggest that APE1 overexpression in CPCs may be a novel strategy to reinforce cardiac cell therapy. ©AlphaMed Press.

Cetylpyridinium chloride mouth rinses alleviate experimental gingivitis by inhibiting dental plaque maturation.

PubMed

Teng, Fei; He, Tao; Huang, Shi; Bo, Cun-Pei; Li, Zhen; Chang, Jin-Lan; Liu, Ji-Quan; Charbonneau, Duane; Xu, Jian; Li, Rui; Ling, Jun-Qi

2016-09-29

Oral rinses containing chemotherapeutic agents, such as cetylpyridinium chloride (CPC), can alleviate plaque-induced gingival infections, but how oral microbiota respond to these treatments in human population remains poorly understood. Via a double-blinded, randomised controlled trial of 91 subjects, the impact of CPC-containing oral rinses on supragingival plaque was investigated in experimental gingivitis, where the subjects, after a 21-day period of dental prophylaxis to achieve healthy gingivae, received either CPC rinses or water for 21 days. Within-subject temporal dynamics of plaque microbiota and symptoms of gingivitis were profiled via 16S ribosomal DNA gene pyrosequencing and assessment with the Mazza gingival index. Cetylpyridinium chloride conferred gingival benefits, as progression of gingival inflammation resulting from a lack of dental hygiene was significantly slower in the mouth rinse group than in the water group due to inhibition of 17 gingivitis-enriched bacterial genera. Tracking of plaque α and β diversity revealed that CPC treatment prevents acquisition of new taxa that would otherwise accumulate but maintains the original biodiversity of healthy plaques. Furthermore, CPC rinses reduced the size, local connectivity and microbiota-wide connectivity of the bacterial correlation network, particularly for nodes representing gingivitis-enriched taxa. The findings of this study provide mechanistic insights into the impact of oral rinses on the progression and maturation of dental plaque in the natural human population.

Cetylpyridinium chloride mouth rinses alleviate experimental gingivitis by inhibiting dental plaque maturation

PubMed Central

Teng, Fei; He, Tao; Huang, Shi; Bo, Cun-Pei; Li, Zhen; Chang, Jin-Lan; Liu, Ji-Quan; Charbonneau, Duane; Xu, Jian; Li, Rui; Ling, Jun-Qi

2016-01-01

Oral rinses containing chemotherapeutic agents, such as cetylpyridinium chloride (CPC), can alleviate plaque-induced gingival infections, but how oral microbiota respond to these treatments in human population remains poorly understood. Via a double-blinded, randomised controlled trial of 91 subjects, the impact of CPC-containing oral rinses on supragingival plaque was investigated in experimental gingivitis, where the subjects, after a 21-day period of dental prophylaxis to achieve healthy gingivae, received either CPC rinses or water for 21 days. Within-subject temporal dynamics of plaque microbiota and symptoms of gingivitis were profiled via 16S ribosomal DNA gene pyrosequencing and assessment with the Mazza gingival index. Cetylpyridinium chloride conferred gingival benefits, as progression of gingival inflammation resulting from a lack of dental hygiene was significantly slower in the mouth rinse group than in the water group due to inhibition of 17 gingivitis-enriched bacterial genera. Tracking of plaque α and β diversity revealed that CPC treatment prevents acquisition of new taxa that would otherwise accumulate but maintains the original biodiversity of healthy plaques. Furthermore, CPC rinses reduced the size, local connectivity and microbiota-wide connectivity of the bacterial correlation network, particularly for nodes representing gingivitis-enriched taxa. The findings of this study provide mechanistic insights into the impact of oral rinses on the progression and maturation of dental plaque in the natural human population. PMID:27680288

Design and Fabrication of Complex Scaffolds for Bone Defect Healing: Combined 3D Plotting of a Calcium Phosphate Cement and a Growth Factor-Loaded Hydrogel.

PubMed

Ahlfeld, Tilman; Akkineni, Ashwini Rahul; Förster, Yvonne; Köhler, Tino; Knaack, Sven; Gelinsky, Michael; Lode, Anja

2017-01-01

Additive manufacturing enables the fabrication of scaffolds with defined architecture. Versatile printing technologies such as extrusion-based 3D plotting allow in addition the incorporation of biological components increasing the capability to restore functional tissues. We have recently described the fabrication of calcium phosphate cement (CPC) scaffolds by 3D plotting of an oil-based CPC paste under mild conditions. In the present study, we have developed a strategy for growth factor loading based on multichannel plotting: a biphasic scaffold design was realised combining CPC with VEGF-laden, highly concentrated hydrogel strands. As hydrogel component, alginate and an alginate-gellan gum blend were evaluated; the blend exhibited a more favourable VEGF release profile and was chosen for biphasic scaffold fabrication. After plotting, two-step post-processing was performed for both, hydrogel crosslinking and CPC setting, which was shown to be compatible with both materials. Finally, a scaffold was designed and fabricated which can be applied for testing in a rat critical size femur defect. Optimization of CPC plotting enabled the fabrication of highly resolved structures with strand diameters of only 200 µm. Micro-computed tomography revealed a precise strand arrangement and an interconnected pore space within the biphasic scaffold even in swollen state of the hydrogel strands.

Modifications of a calcium phosphate cement with biomolecules--influence on nanostructure, material, and biological properties.

PubMed

Vater, Corina; Lode, Anja; Bernhardt, Anne; Reinstorf, Antje; Nies, Berthold; Gelinsky, Michael

2010-12-01

Calcium phosphate cements (CPC), forming hydroxyapatite during the setting reaction, are characterized by good biocompatibility and osteoconductivity, however, their remodeling into native bone tissue is slow. One strategy to improve remodeling and bone regeneration is the directed modification of their nanostructure. In this study, a CPC was set in the presence of cocarboxylase, glucuronic acid, tartaric acid, α-glucose-1-phosphate, L-arginine, L-aspartic acid, and L-lysine, respectively, with the aim to influence formation and growth of hydroxyapatite crystals through the functional groups of these biomolecules. Except for glucuronic acid, all these modifications resulted in the formation of smaller and more agglomerated hydroxyapatite particles which had a positive impact on the biological performance indicated by first experiments with the human osteoblast cell line hFOB 1.19. Moreover, adhesion, proliferation, and osteogenic differentiation of human bone marrow-derived mesenchymal stem cells (hBMSC) as well as binding of the growth factors BMP-2 and VEGF was investigated on CPC modified with cocarboxylase, arginine, and aspartic acid. Initial adhesion of hBMSC was improved on these three modifications and proliferation was enhanced on CPC modified with cocarboxylase and arginine whereas osteogenic differentiation remained unaffected. Modification of the CPC with arginine and aspartic acid, but not with cocarboxylase, led to a higher BMP-2 binding. © 2010 Wiley Periodicals, Inc. J Biomed Mater Res Part A, 2010.

Objective measurements of the penile angulation are significantly different than self-estimated magnitude among patients with penile curvature.

PubMed

Liguori, Giovanni; Salonia, Andrea; Garaffa, Giulio; Chiriacò, Giovanni; Pavan, Nicola; Cavallini, Giorgio; Trombetta, Carlo

2018-01-01

The study was aimed to assess the presence of actual differences between the objective and the perceived magnitude of a curvature between patients affected by Peyronie's disease (PD) and congenital penile curvature (CPC). Wee analysed a cohort of 88 consecutive patients seeking medical help for either CPC or PD. All patients were invited to provide a self-made drawing of their penis in erection in order to obtain self-provided description of the deformity. An objective measurement of the deformity was also performed drawing two intersecting lines through the center of the distal and proximal straight section of the penile shaft. Our findings showed significant differences between patient self-estimation and the objective measurements of the penile angulation performed by trained experts, with only 32% of patients correctly assessing their own curvature. Overall, patients tended to overestimate (56%) their degree of curvature, but the results are different in patients with PD than those with CPC. In the 60 men (68%) who did not accurately assess their curvature, PD patients generally overestimated their curvature versus CPC patients (67% vs 16%). On the contrary CPC patients underestimated their curvature compared to PD (42% vs. 4%). In order to improve patients' satisfaction rates, the surgeon needs to take into consideration the patient's perception of the deformity when planning the type of surgical correction. Copyright® by the International Brazilian Journal of Urology.

A new synthetic granular calcium phosphate compound induces new bone in a sinus lift rabbit model.

PubMed

Trbakovic, Amela; Hedenqvist, Patricia; Mellgren, Torbjörn; Ley, Cecilia; Hilborn, Jöns; Ossipov, Dmitri; Ekman, Stina; Johansson, Carina B; Jensen-Waern, Marianne; Thor, Andreas

2018-03-01

The aim of this study was to investigate if a synthetic granular calcium phosphate compound (CPC) and a composite bisphosphonate-linked hyaluronic acid-calcium phosphate hydrogel (HABP·CaP) induced similar or more amount of bone as bovine mineral in a modified sinus lift rabbit model. Eighteen adult male New Zeeland White rabbits, received randomly one of the two test materials on a random side of the face, and bovine mineral as control on the contralateral side. In a sinus lift, the sinus mucosa was elevated and a titanium mini-implant was placed in the alveolar bone. Augmentation material (CPC, HABP·CaP or bovine bone) was applied in the space around the implant. The rabbits were euthanized three months after surgery and qualitative and histomorphometric evaluation were conducted. Histomorphometric evaluation included three different regions of interest (ROIs) and the bone to implant contact on each installed implant. Qualitative assessment (p = <.05), histomorphometric evaluations (p = < .01), and implant incorporation (p = <.05) showed that CPC and bovine mineral induced similar amount of bone and more than the HABP·CaP hydrogel. CPC induced similar amount of bone as bovine mineral and both materials induced more bone than HABP·CaP hydrogel. The CPC is suggested as a synthetic alternative for augmentations in the maxillofacial area. Copyright © 2017 Elsevier Ltd. All rights reserved.

Toward the bi-modal camber morphing of large aircraft wing flaps: the CleanSky experience

NASA Astrophysics Data System (ADS)

Pecora, R.; Amoroso, F.; Magnifico, M.

2016-04-01

The Green Regional Aircraft (GRA), one of the six CleanSky platforms, represents the largest European effort toward the greening of next generation air transportation through the implementation of advanced aircraft technologies. In this framework researches were carried out to develop an innovative wing flap enabling airfoil morphing according to two different modes depending on aircraft flight condition and flap setting: - Camber morphing mode. Morphing of the flap camber to enhance high-lift performances during take-off and landing (flap deployed); - Tab-like morphing mode. Upwards and downwards deflection of the flap tip during cruise (flap stowed) for load control at high speed and consequent optimization of aerodynamic efficiency. A true-scale flap segment of a reference aircraft (EASA CS25 category) was selected as investigation domain for the new architecture in order to duly face the challenges posed by real wing installation issues especially with reference to the tapered geometrical layout and 3D aerodynamic loads distributions. The investigation domain covered the flap region spanning 3.6 m from the wing kink and resulted characterized by a taper ratio equal to 0.75 with a root chord of 1.2 m. High TRL solutions for the adaptive structure, actuation and control system were duly analyzed and integrated while assuring overall device compliance with industrial standards and applicable airworthiness requirements.

Aggressive mimicry coexists with mutualism in an aphid.

PubMed

Salazar, Adrián; Fürstenau, Benjamin; Quero, Carmen; Pérez-Hidalgo, Nicolás; Carazo, Pau; Font, Enrique; Martínez-Torres, David

2015-01-27

Understanding the evolutionary transition from interspecific exploitation to cooperation is a major challenge in evolutionary biology. Ant-aphid relationships represent an ideal system to this end because they encompass a coevolutionary continuum of interactions ranging from mutualism to antagonism. In this study, we report an unprecedented interaction along this continuum: aggressive mimicry in aphids. We show that two morphs clonally produced by the aphid Paracletus cimiciformis during its root-dwelling phase establish relationships with ants at opposite sides of the mutualism-antagonism continuum. Although one of these morphs exhibits the conventional trophobiotic (mutualistic) relationship with ants of the genus Tetramorium, aphids of the alternative morph are transported by the ants to their brood chamber and cared for as if they were true ant larvae. Gas chromatography-mass spectrometry analyses reveal that the innate cuticular hydrocarbon profile of the mimic morph resembles the profile of ant larvae more than that of the alternative, genetically identical nonmimic morph. Furthermore, we show that, once in the brood chamber, mimic aphids suck on ant larva hemolymph. These results not only add aphids to the limited list of arthropods known to biosynthesize the cuticular chemicals of their deceived hosts to exploit their resources but describe a remarkable case of plastic aggressive mimicry. The present work adds a previously unidentified dimension to the classical textbook paradigm of aphid-ant relationships by showcasing a complex system at the evolutionary interface between cooperation and exploitation.

Aggressive mimicry coexists with mutualism in an aphid

PubMed Central

Salazar, Adrián; Fürstenau, Benjamin; Quero, Carmen; Pérez-Hidalgo, Nicolás; Carazo, Pau; Font, Enrique; Martínez-Torres, David

2015-01-01

Understanding the evolutionary transition from interspecific exploitation to cooperation is a major challenge in evolutionary biology. Ant–aphid relationships represent an ideal system to this end because they encompass a coevolutionary continuum of interactions ranging from mutualism to antagonism. In this study, we report an unprecedented interaction along this continuum: aggressive mimicry in aphids. We show that two morphs clonally produced by the aphid Paracletus cimiciformis during its root-dwelling phase establish relationships with ants at opposite sides of the mutualism–antagonism continuum. Although one of these morphs exhibits the conventional trophobiotic (mutualistic) relationship with ants of the genus Tetramorium, aphids of the alternative morph are transported by the ants to their brood chamber and cared for as if they were true ant larvae. Gas chromatography-mass spectrometry analyses reveal that the innate cuticular hydrocarbon profile of the mimic morph resembles the profile of ant larvae more than that of the alternative, genetically identical nonmimic morph. Furthermore, we show that, once in the brood chamber, mimic aphids suck on ant larva hemolymph. These results not only add aphids to the limited list of arthropods known to biosynthesize the cuticular chemicals of their deceived hosts to exploit their resources but describe a remarkable case of plastic aggressive mimicry. The present work adds a previously unidentified dimension to the classical textbook paradigm of aphid–ant relationships by showcasing a complex system at the evolutionary interface between cooperation and exploitation. PMID:25583474

Molpher: a software framework for systematic chemical space exploration.

PubMed

Hoksza, David; Skoda, Petr; Voršilák, Milan; Svozil, Daniel

2014-03-21

Chemical space is virtual space occupied by all chemically meaningful organic compounds. It is an important concept in contemporary chemoinformatics research, and its systematic exploration is vital to the discovery of either novel drugs or new tools for chemical biology. In this paper, we describe Molpher, an open-source framework for the systematic exploration of chemical space. Through a process we term 'molecular morphing', Molpher produces a path of structurally-related compounds. This path is generated by the iterative application of so-called 'morphing operators' that represent simple structural changes, such as the addition or removal of an atom or a bond. Molpher incorporates an optimized parallel exploration algorithm, compound logging and a two-dimensional visualization of the exploration process. Its feature set can be easily extended by implementing additional morphing operators, chemical fingerprints, similarity measures and visualization methods. Molpher not only offers an intuitive graphical user interface, but also can be run in batch mode. This enables users to easily incorporate molecular morphing into their existing drug discovery pipelines. Molpher is an open-source software framework for the design of virtual chemical libraries focused on a particular mechanistic class of compounds. These libraries, represented by a morphing path and its surroundings, provide valuable starting data for future in silico and in vitro experiments. Molpher is highly extensible and can be easily incorporated into any existing computational drug design pipeline.

Efficient quantum computing using coherent photon conversion.

PubMed

Langford, N K; Ramelow, S; Prevedel, R; Munro, W J; Milburn, G J; Zeilinger, A

2011-10-12

Single photons are excellent quantum information carriers: they were used in the earliest demonstrations of entanglement and in the production of the highest-quality entanglement reported so far. However, current schemes for preparing, processing and measuring them are inefficient. For example, down-conversion provides heralded, but randomly timed, single photons, and linear optics gates are inherently probabilistic. Here we introduce a deterministic process--coherent photon conversion (CPC)--that provides a new way to generate and process complex, multiquanta states for photonic quantum information applications. The technique uses classically pumped nonlinearities to induce coherent oscillations between orthogonal states of multiple quantum excitations. One example of CPC, based on a pumped four-wave-mixing interaction, is shown to yield a single, versatile process that provides a full set of photonic quantum processing tools. This set satisfies the DiVincenzo criteria for a scalable quantum computing architecture, including deterministic multiqubit entanglement gates (based on a novel form of photon-photon interaction), high-quality heralded single- and multiphoton states free from higher-order imperfections, and robust, high-efficiency detection. It can also be used to produce heralded multiphoton entanglement, create optically switchable quantum circuits and implement an improved form of down-conversion with reduced higher-order effects. Such tools are valuable building blocks for many quantum-enabled technologies. Finally, using photonic crystal fibres we experimentally demonstrate quantum correlations arising from a four-colour nonlinear process suitable for CPC and use these measurements to study the feasibility of reaching the deterministic regime with current technology. Our scheme, which is based on interacting bosonic fields, is not restricted to optical systems but could also be implemented in optomechanical, electromechanical and superconducting systems with extremely strong intrinsic nonlinearities. Furthermore, exploiting higher-order nonlinearities with multiple pump fields yields a mechanism for multiparty mediation of the complex, coherent dynamics.

Eddy Covariance Measurements of Turbulent Fluxes of Atmospheric Aerosols From a Moving Ship From the Sea of Okhotsk to the Arctic Ocean

NASA Astrophysics Data System (ADS)

Griessbaum, F.; Narita, Y.; Held, A.; Klemm, O.; Uematsu, M.

2006-12-01

Recent studies of emission and deposition of atmospheric aerosols employing the eddy covariance technique (EC) have been conducted in the terrestrial and marine boundary layer, the latter mainly limited to fixed platforms in the coastal domain. The captioned approach enables us to study the sinks and sources of atmospheric aerosols and their impact on the sea/air exchange of materials and on the direct and indirect radiation effect in the marine boundary layer from moving platforms, such as vessels. Measurements of atmospheric parameters from a ship are challenging especially due to the flow distortion caused by the ship's superstructure and the vessel's motions. It is known from recent work employing computational fluid dynamics (CFD) on the geometry of vessels, that the most suitable place for undistorted measurements is at the very bow and the most elevated location, commonly the foremast. For this reason, the entire eddy covariance instrumentation was fixed at the very top of the foremast, consisting of: sonic anemometer, condensation particle counter (CPC, from 5 nm particle diameter), fog droplet spectrometer (2 to 50 μm droplet diameter), CO{_2}/H{_2}O Analyser and an inertial sensing system. In order to operate the CPC also while the vessel is underway or in rough sea conditions, the max tilt angle (rolling and pitching) of the CPC was technically improved from 10° up to over 30°. This EC-measurement was conducted over the high primary productive region with high frequency of sea fog appearance during the cruise MR06-4 on R/V Mirai from Hokkaido, Japan, to the Chukchi Sea in Arctic Ocean, lasting from August 2 through September 29, 2006. Initial results will be presented and discussed.

CPC - Monitoring & Data: Regional Climate Maps

Science.gov Websites

Weather Service NWS logo - Click to go to the NWS home page Climate Prediction Center Site Map News Information CPC Web Team HOME > Monitoring and Data > Global Climate Data & Maps > Global Regional Climate Maps Regional Climate Maps Banner The Monthly regional analyses products are usually

Three new combinations in Drepanopeziza for species on poplar

USDA-ARS?s Scientific Manuscript database

Three species of Drepanopeziza that cause diseases of poplars have been known using scientific names for their sexual and asexual morphs, which is no longer allowed with the change to one scientific name for fungi. For each species, the oldest epithet is provided by the asexual morph; however, neith...

Measuring Psychological Capital: Construction and Validation of the Compound PsyCap Scale (CPC-12)

PubMed Central

Lorenz, Timo; Beer, Clemens; Pütz, Jan; Heinitz, Kathrin

2016-01-01

With the Psychological Capital Questionnaire (PCQ) being the standard measure to assess psychological capital (PsyCap) in the context of organizations, this paper aims to broaden this domain-specific approach by introducing a measure with universal claim. Two studies were conducted to create and validate a German self-report scale (CPC-12) measuring PsyCap. We performed confirmatory factor analyses and correlations with other positive psychological constructs on the data of two German samples (N1 = 321; N2 = 202). The twelve-item CPC-12 exhibits the anticipated factorial structure with a very good model fit and associations to other constructs concur with previous findings with other measures of PsyCap. PMID:27035437

KSC-2012-5609

NASA Image and Video Library

2012-09-19

CAPE CANAVERAL, Fla. -- NASA's Commercial Crew Program, or CCP, hosts a pre-proposal conference to inform prospective companies about the recently released request for contract proposals and updates to the certification requirements for crewed missions to the International Space Station, or ISS. The two-phase certification process, called Certification Products Contract, or CPC, will enable NASA to eventually purchase service missions to fly astronauts to and from the ISS. From left, Ed Mango, CCP's program manager Steve Janney, CPC contracting officer Maria Collura, CCP certification manager Tom Simon, CPC Evaluation Team chair Brent Jett, CCP deputy program manager and Kathy Lueders, manager of the ISS Transportation Integration Office. To learn more about CCP, visit www.nasa.gov/commercialcrew. Photo credit: Kim Shiflett

KSC-2012-5603

NASA Image and Video Library

2012-09-19

CAPE CANAVERAL, Fla. -- NASA's Commercial Crew Program, or CCP, hosts a pre-proposal conference to inform prospective companies about the recently released request for contract proposals and updates to the certification requirements for crewed missions to the International Space Station, or ISS. The two-phase certification process, called Certification Products Contract, or CPC, will enable NASA to eventually purchase service missions to fly astronauts to and from the ISS. From left, Ed Mango, CCP's program manager Steve Janney, CPC contracting officer Maria Collura, CCP certification manager Tom Simon, CPC Evaluation Team chair Brent Jett, CCP deputy program manager and Kathy Lueders, manager of the ISS Transportation Integration Office. To learn more about CCP, visit www.nasa.gov/commercialcrew. Photo credit: Kim Shiflett

Effects of an herbicide on physiology, morphology, and fitness of the dung beetle Euoniticellus intermedius (Coleoptera: Scarabaeidae).

PubMed

González-Tokman, Daniel; Martínez-Morales, Imelda; Farrera, Arodi; Del Rosario Ortiz-Zayas, María; Lumaret, Jean-Pierre

2017-01-01

Some agrochemical compounds threaten nontarget organisms and their functions in the ecosystem. The authors experimentally evaluated the effects of one of the most common herbicide mixtures used worldwide, containing 2,4-dichlorophenoxyacetic acid and picloram, on dung beetles, which play fundamental roles in the function of natural and managed ecosystems. The present study employed techniques of physiology and geometric morphometrics, besides including fitness measurements, to assess the effects of the herbicide in the introduced beetle Euoniticellus intermedius. Because herbicide components promote oxidative stress and affect survival in certain insects, the authors predicted negative effects on the beetles. Unexpectedly, no effect of herbicide concentration was found on clutch size, sex ratio, and fluctuating asymmetry, and it even increased physiological condition and body size in exposed beetles. Because the studied species presents 2 male morphs, the authors, for the first time, evaluated the effect of a pollutant on the ratio of these morphs. Contrary to the prediction, the herbicide mixture increased the proportion of major males. Thus, the herbicide does not threaten populations of the studied beetles. The present study discusses how both negative and positive effects of pollutants on wild animals modify natural and sexual selection processes occurring in nature, which ultimately impact population dynamics. The authors recommend the use of physiological and geometric morphometrics techniques to assess the impact of pollutants on nontarget animals. Environ Toxicol Chem 2017;36:96-102. © 2016 SETAC. © 2016 SETAC.

A Cell Model to Evaluate Chemical Effects on Adult Human Cardiac Progenitor Cell Differentiation and Function

EPA Science Inventory

Adult cardiac stem cells (CSC) and progenitor cells (CPC) represent a population of cells in the heart critical for its regeneration and function over a lifetime. The impact of chemicals on adult human CSC/CPC differentiation and function is unknown. Research was conducted to dev...

Standardization of clinical pharmacist's activities: Methodology.

PubMed

Gregorová, Jana; Rychlíčková, Jitka; Šaloun, Jan

2017-09-01

Establishing standardized and controlled system of work at a clinical pharmacy department and establishing effective recording of activities of a group of four clinical pharmacist when providing clinical pharmaceutical care (CPC) in a hospital. The duration of evaluated period is 5.5 years. The first part was defining the purpose, methods and activities of clinical pharmaceutical care, the next part was designing the software for recording patient's data and CPC activities. To verify the functionality of our system the third part was conducted (from January 1, 2015 to June 30, 2015). CPC activities were defined precisely. During the 6 months period, 3946 patients were reviewed (17% of patients admitted), in this group, 41% patients was labeled as risk (these patients had one or more risk factor). 1722 repeated reviews were performed, 884 drug therapy recommendations were recorded. The calculated average time necessary for one CPC activity is 28 min. During the 5 year period, standardized system of work in clinical pharmacy department was established. This system is based on clearly defined activities and it enables external control. Our results supply data for negotiations with health insurance companies.

Unusual nanosized associates of carboxy-calix[4]resorcinarene and cetylpyridinium chloride: the macrocycle as a glue for surfactant micelles.

PubMed

Morozova, Ju E; Syakaev, V V; Shalaeva, Ya V; Ermakova, A M; Nizameev, I R; Kadirov, M K; Voloshina, A D; Zobov, V V; Antipin, I S; Konovalov, A I

2017-03-08

The association of cetylpyridinium chloride (CPC) micelles in the presence of octaacetated tetraphenyleneoxymethylcalix[4]resorcinarene (CR) leads to the formation of unusual spherical supramolecular nanoparticles (SNPs). Within the range of CR/CPC molar ratios from 10/1 to 1/10 (except for 1/8), CR, acting as a counterion, decreases the critical micelle concentration of CPC by one order of magnitude and leads to the formation of SNPs with an average hydrodynamic radius of 164 nm and an average zeta potential of -60 mV. The formation of SNPs was studied by NMR FT-PGSE and 2D NOESY, DLS, TEM, fluorimetry, and UV-Vis methods. The stability of SNPs at different temperatures and pH values and in the presence of electrolytes was investigated. The specificity of the interactions of the SNPs with substrates that were preferentially bound by a macrocycle or CPC micelle was studied. The enhancement of cation dye binding in the presence of SNPs is shown. The presented supramolecular system may serve as a nanocapsule for water-soluble and water-insoluble compounds.

The Behavior of Environmentally Friendly Corrosion Preventative Compounds in an Aggressive Coastal Marine Environment

NASA Technical Reports Server (NTRS)

Montgomery, Eliza L.; Calle, Luz Marina; Curran Jerome C.; Kolody, Mark R.

2013-01-01

The shift to use environmentally friendly technologies throughout future space-related launch programs prompted a study aimed at replacing current petroleum and solvent-based Corrosion Preventive Compounds (CPCs) with environmentally friendly alternatives. The work in this paper focused on the identification and evaluation of environmentally friendly CPCs for use in protecting flight hardware and ground support equipment from atmospheric corrosion. The CPCs, while a temporary protective coating, must survive in the aggressive coastal marine environment that exists throughout the Kennedy Space Center, Florida. The different protection behaviors of fifteen different soft film CPCs, both common petroleum-based and newer environmentally friendly types, were evaluated on various steel and aluminum substrates. The CPC and substrate systems were subjected to atmospheric testing at the Kennedy Space Center's Beachside Atmospheric Corrosion Test Site, as well as cyclic accelerated corrosion testing. Each CPC also underwent physical characterization and launch-related compatibility testing . The initial results for the fifteen CPC systems are reported : Key words: corrosion preventive compound, CPC, spaceport, environmentally friendly, atmospheric exposure, marine, carbon steel, aluminum alloy, galvanic corrosion, wire on bolt.

Cross-regulation between Aurora B and Citron kinase controls midbody architecture in cytokinesis

PubMed Central

McKenzie, Callum; Bassi, Zuni I.; Debski, Janusz; Gottardo, Marco; Callaini, Giuliano; Dadlez, Michal; D'Avino, Pier Paolo

2016-01-01

Cytokinesis culminates in the final separation, or abscission, of the two daughter cells at the end of cell division. Abscission relies on an organelle, the midbody, which forms at the intercellular bridge and is composed of various proteins arranged in a precise stereotypic pattern. The molecular mechanisms controlling midbody organization and function, however, are obscure. Here we show that proper midbody architecture requires cross-regulation between two cell division kinases, Citron kinase (CIT-K) and Aurora B, the kinase component of the chromosomal passenger complex (CPC). CIT-K interacts directly with three CPC components and is required for proper midbody architecture and the orderly arrangement of midbody proteins, including the CPC. In addition, we show that CIT-K promotes Aurora B activity through phosphorylation of the INCENP CPC subunit at the TSS motif. In turn, Aurora B controls CIT-K localization and association with its central spindle partners through phosphorylation of CIT-K's coiled coil domain. Our results identify, for the first time, a cross-regulatory mechanism between two kinases during cytokinesis, which is crucial for establishing the stereotyped organization of midbody proteins. PMID:27009191

Immunostaining of the androgen receptor and sequence analysis of its DNA-binding domain in canine prostate cancer.

PubMed

Lai, Chen-Li; van den Ham, René; Mol, Jan; Teske, Erik

2009-09-01

Prostate cancer in the dog (cPC) has many features in common with hormone refractory human prostate cancer. As cPC is seen more often in castrated dogs, the contribution of the androgen receptor (AR) to the development of prostate cancer remains questionable. The aim of the present study was to evaluate the presence of the AR by immunohistochemistry in cPC. AR staining was observed in most tumors from intact and castrated dogs, but the proportion of positive cells and the staining intensity were much lower than in the prostate of healthy, non-castrated dogs. Most of the positive staining was seen in the cytoplasm rather than in the nuclei of the tumor cells. The predominant cytoplasmic localization was not related to mutations in exon 3 of the DNA-binding domain of the AR, as shown by sequence analysis of microdissected AR positive tumor cells. Other mechanisms that lead to an impaired androgen-AR signaling or a basal/stem cell like origin may explain the low cytoplasmic AR staining in cPC.

Optical performance effects of the misalignment of nonimaging optics solar collectors

NASA Astrophysics Data System (ADS)

Ferry, Jonathan; Ricketts, Melissa; Winston, Roland

2017-09-01

The use of non-imaging optics in the application of high temperature solar thermal collectors can be extremely advantageous in eliminating the need to track the sun. The stationary nature of non-imaging optics collectors, commonly called compound parabolic concentrators (CPC's), present a unique design challenge when orienting them to collect sunlight. Many facilities throughout the world that adopt CPCs are not situated to orient the collectors in the ideal angle facing the sun. This East-West misalignment can adversely affect the optical and power performance of the CPC collector. To characterize how this misalignment effects CPCs, reverse raytracing simulations are conducted for varying offset angles of the collectors from solar South. Optical performance is analyzed for an ideal East-West oriented CPC with a 40-degree acceptance angle. Direction cosine plots are used to develop a ratio of annual solar collection by the CPC over the total annual solar input. From these simulations, average annual collector performance is given for offset angles ranging from 0 to 90 degrees for different Earth Latitudes in 10 degree increments.

Stimuli-responsive supramolecular micellar assemblies of cetylpyridinium chloride with cucurbit[5/7]urils.

PubMed

Choudhury, Sharmistha Dutta; Barooah, Nilotpal; Aswal, Vinod Kumar; Pal, Haridas; Bhasikuttan, Achikanath C; Mohanty, Jyotirmayee

2014-05-21

This article demonstrates, for the first time, construction of novel cucurbituril (CB)-adorned supramolecular micellar assemblies of a cationic surfactant, cetylpyridinium chloride (CPC), through noncovalent host-guest interactions. The distinct cation receptor features and cavity dimensions of the CB5 and CB7 homologues assert that the macrocyclic hosts remain complexed with the CPC monomers and take part in the micelle formation, a unique observation in contrast to that of the classical host, β-cyclodextrin. The cooperative contributions of the CB macrocycles in the micelle formation have been documented by the photochemical, surface tension, conductivity, DOSY NMR, and SANS measurements. The contrasting downward and upward shifts in the cmc of the CPC surfactant, respectively, with CB5 and CB7 hosts provide a unique opportunity for the controlled tuning of the micellization region for CPC from 0.57 to 1.6 mM, by using a combination of the macrocyclic hosts. The article also establishes the reversible response of these soft supramolecular micellar structures to thermal-stimuli, which projects their utility for on-demand smart drug-delivery vehicles.

The Comprehensive Primary Care Initiative: Effects On Spending, Quality, Patients, And Physicians.

PubMed

Peikes, Deborah; Dale, Stacy; Ghosh, Arkadipta; Taylor, Erin Fries; Swankoski, Kaylyn; O'Malley, Ann S; Day, Timothy J; Duda, Nancy; Singh, Pragya; Anglin, Grace; Sessums, Laura L; Brown, Randall S

2018-06-01

The Comprehensive Primary Care Initiative (CPC), a health care delivery model developed by the Centers for Medicare and Medicaid Services (CMS), tested whether multipayer support of 502 primary care practices across the country would improve primary care delivery, improve care quality, or reduce spending. We evaluated the initiative's effects on care delivery and outcomes for fee-for-service Medicare beneficiaries attributed to initiative practices, relative to those attributed to matched comparison practices. CPC practices reported improvements in primary care delivery, including care management for high-risk patients, enhanced access, and improved coordination of care transitions. The initiative slowed growth in emergency department visits by 2 percent in CPC practices, relative to comparison practices. However, it did not reduce Medicare spending enough to cover care management fees or appreciably improve physician or beneficiary experience or practice performance on a limited set of Medicare claims-based quality measures. As CMS and other payers increasingly use alternative payment models that reward quality and value, CPC provides important lessons about supporting practices in transforming care.

Missteps, Flaws and Morphings in Children's Musical Play: Snapshots from School Playgrounds

ERIC Educational Resources Information Center

Countryman, June

2014-01-01

This article, drawing upon fieldwork from a larger project investigating the nature of children's self-chosen musical play, explores instances of play that stumble and either morph into something else or are abandoned altogether. Four vignettes of musical play are described, documented during recess observations at several Canadian elementary…

Design and Testing of a Morphing Wing for an Experimental UAV

DTIC Science & Technology

2007-11-01

line through the use of conformal flaps [6]. Variable cant angle winglets [7] and variable span wing [8] research has also been made. RTO-MP-AVT...A.Gatto and M.I. Friswell, “The Application of Variable Cant Angle Winglets for Morphing Aircraft Control”, University of Bristol, AIAA2006-3660, 2006

Identity-Specific Face Adaptation Effects: Evidence for Abstractive Face Representations

ERIC Educational Resources Information Center

Hole, Graham

2011-01-01

The effects of selective adaptation on familiar face perception were examined. After prolonged exposure to photographs of a celebrity, participants saw a series of ambiguous morphs that were varying mixtures between the face of that person and a different celebrity. Participants judged fewer of the morphs to resemble the celebrity to which they…

Face and Object Discrimination in Autism, and Relationship to IQ and Age

ERIC Educational Resources Information Center

Pallett, Pamela M.; Cohen, Shereen J.; Dobkins, Karen R.

2014-01-01

The current study tested fine discrimination of upright and inverted faces and objects in adolescents with Autism Spectrum Disorder (ASD) as compared to age- and IQ-matched controls. Discrimination sensitivity was tested using morphed faces and morphed objects, and all stimuli were equated in low-level visual characteristics (luminance, contrast,…

Spatial Variation in Body Size and Wing Dimorphism Correlates With Environmental Conditions in the Grasshopper Dichroplus vittatus (Orthoptera: Acrididae).

PubMed

Rosetti, Natalia; Remis, Maria I

2018-06-06

Wing dimorphism occurs widely in insects and involves discontinuous variation in a wide variety of traits involved in fight and reproduction. In the current study, we analyzed the spatial pattern of wing dimorphism and intraspecific morphometric variation in nine natural populations of the grasshopper Dichroplus vittatus (Bruner; Orthoptera: Acrididae) in Argentina. Considerable body size differences among populations, between sexes and wing morphs were detected. As a general trend, females were larger than males and macropterous individuals showed increased thorax length over brachypterous which can be explained by the morphological requirements for the development of flight muscles in the thoracic cavity favoring dispersal. Moreover, when comparing wing morphs, a higher phenotypic variability was detected in macropterous females. The frequency of macropterous individuals showed negative correlation with longitude and positive with precipitations, indicating that the macropterous morph is more frequent in the humid eastern part of the studied area. Our results provide valuable about spatial variation of fully winged morph and revealed geographic areas in which the species would experience greater dispersal capacity.

Female Preference for Sympatric vs. Allopatric Male Throat Color Morphs in the Mesquite Lizard (Sceloporus grammicus) Species Complex

PubMed Central

Bastiaans, Elizabeth; Bastiaans, Mary Jane; Morinaga, Gen; Castañeda Gaytán, José Gamaliel; Marshall, Jonathon C.; Bane, Brendan; de la Cruz, Fausto Méndez; Sinervo, Barry

2014-01-01

Color polymorphic sexual signals are often associated with alternative reproductive behaviors within populations, and the number, frequency, or type of morphs present often vary among populations. When these differences lead to assortative mating by population, the study of such polymorphic taxa may shed light on speciation mechanisms. We studied two populations of a lizard with polymorphic throat color, an important sexual signal. Males in one population exhibit orange, yellow, or blue throats; whereas males in the other exhibit orange, yellow, or white throats. We assessed female behavior when choosing between allopatric and sympatric males. We asked whether females discriminated more when the allopatric male was of an unfamiliar morph than when the allopatric male was similar in coloration to the sympatric male. We found that female rejection of allopatric males relative to sympatric males was more pronounced when males in a pair were more different in throat color. Our findings may help illuminate how behavioral responses to color morph differences between populations with polymorphic sexual signals contribute to reproductive isolation. PMID:24718297

Why morphology matters in birds and UAV's: How scale affects attitude wind sensitivity

NASA Astrophysics Data System (ADS)

Gamble, L. L.; Inman, D. J.

2017-11-01

Although natural fliers have been shown to morph their geometry to adapt to unfavorable wind loading, there exists heavy skepticism within the aviation community regarding the benefits and necessity of morphing aircraft technology. Here, we develop a vector derivation that characterizes how high winds affect the overall flight velocity and sideslip for both natural and manmade fliers. This derivation is formulated in such a way that only a single non-dimensional velocity parameter is needed to quantify the response. We show mathematically that in high winds, low-altitude fliers are more prone to substantial changes in the sideslip angle, struggle to maintain gliding velocity, and experience five times the peak sideslip sensitivity when compared to high-altitude fliers. In order to counteract these adverse changes, low-altitude fliers require a high degree of controllability which can be achieved through extreme morphological changes. The results presented here highlight the importance of integrating morphing concepts into future low-altitude aircraft designs and provide a formulation to help designers decide whether or not to pursue adaptive morphing technology based on a single readily determinable parameter.

A Novel SMA-based Concept for Airfoil Structural Morphing

NASA Astrophysics Data System (ADS)

Barbarino, S.; Pecora, R.; Lecce, L.; Concilio, A.; Ameduri, S.; Calvi, E.

2009-08-01

The adaptive structures concept is of great interest in the aerospace field because of the several benefits which can be accomplished in the fields including noise reduction, load alleviation, weight reduction, etc., at a level in which they can be considered as compulsory in the design of future aircraft. Improvements in terms of the aerodynamic efficiency, aeroelastic behavior, stability, and manoeuvrability performance have already been proved through many international studies in the past. In the family of the Smart Materials, Shape Memory Alloys (SMA) seem to be a suitable solution for many static applications. Their high structural integrability in conjunction with actuation capabilities and a favorable performance per weight ratio, allows the development of original architectures. In this study, a morphing wing trailing edge concept is presented; morphing ability was introduced with the aim of replacing a conventional flap device. A compliant rib structure was designed, based on SMA actuators exhibiting structural potential (bearing external aerodynamic loads). Numerical results, achieved through a FE approach, are presented in terms of trailing edge induced displacement and morphed shape.

Variation in wing pattern and palatability in a female-limited polymorphic mimicry system

PubMed Central

Long, Elizabeth C; Hahn, Thomas P; Shapiro, Arthur M

2014-01-01

Checkerspot butterflies in the genera Euphydryas and Chlosyne exhibit phenotypic polymorphisms along a well-defined latitudinal and elevational gradient in California. The patterns of phenotypic variation in Euphydryas chalcedona, Chlosyne palla, and Chlosyne hoffmanni suggest a mimetic relationship; in addition, the specific patterns of variation in C. palla suggest a female-limited polymorphic mimicry system (FPM). However, the existence of polymorphic models runs counter to predictions of mimicry theory. Palatability trials were undertaken to assess whether or not the different color morphs of each species were distasteful or toxic to a generalized avian predator, the European starling (Sturnus vulgaris). Results indicate that the black morph of E. chalcedona is distasteful, but not toxic, to predators, while the red morph is palatable. C . hoffmanni and both color morphs of C. palla are palatable to predators. Predators that learn to reject black E. chalcedona also reject black C. palla, suggesting that the latter is a FPM of the former. C. hoffmanni does not appear to be involved in this mimetic relationship. PMID:25512850

Selective loss of polymorphic mating types is associated with rapid phenotypic evolution during morphic speciation.

PubMed

Corl, Ammon; Davis, Alison R; Kuchta, Shawn R; Sinervo, Barry

2010-03-02

Polymorphism may play an important role in speciation because new species could originate from the distinctive morphs observed in polymorphic populations. However, much remains to be understood about the process by which morphs found new species. To detail the steps of this mode of speciation, we studied the geographic variation and evolutionary history of a throat color polymorphism that distinguishes the "rock-paper-scissors" mating strategies of the side-blotched lizard, Uta stansburiana. We found that the polymorphism is geographically widespread and has been maintained for millions of years. However, there are many populations with reduced numbers of throat color morphs. Phylogenetic reconstruction showed that the polymorphism is ancestral, but it has been independently lost eight times, often giving rise to morphologically distinct subspecies/species. Changes to the polymorphism likely involved selection because the allele for one particular male strategy, the "sneaker" morph, has been lost in all cases. Polymorphism loss was associated with accelerated evolution of male size, female size, and sexual dimorphism, which suggests that polymorphism loss can promote rapid divergence among populations and aid species formation.

Pigment cell mechanism of postembryonic stripe pattern formation in the Japanese four-lined snake.

PubMed

Murakami, Arata; Hasegawa, Masami; Kuriyama, Takeo

2016-02-01

Postembryonic changes in the dermal and epidermal pigment cell architecture of the striped and nonstriped morph of the Japanese four-lined snake Elaphe quadrivirgata were examined to reveal stripe pattern formation after hatching. The striped and nonstriped morphs were distinguishable at the hatching, suggesting that the basis of stripe pattern was formed during embryonic development. In the striped morph, the color of stripes changed from red-brown in juveniles to vivid dark-brown in adults, and density of dermal melanophore increased much more in the stripe than background dorsal scales with growth. This increase in density of dermal melanophore was accompanied not only by the increased epidermal melanophore density but also by the change in vertical structures of dermal melanophore. By contrast, the density of epidermal and dermal melanophore evenly increased over the dorsal scales in the nonstriped morph. Thus, the increased vividness of the stripe pattern after hatching is achieved through localized increase of melanophore density particularly in the stripe region but not over the whole dorsal scales. © 2015 Wiley Periodicals, Inc.

Electrodialytic Transport Properties of Anion-Exchange Membranes Prepared from Poly(vinyl alcohol) and Poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride).

PubMed

Jikihara, Atsushi; Ohashi, Reina; Kakihana, Yuriko; Higa, Mitsuru; Kobayashi, Kenichi

2013-01-02

Random-type anion-exchange membranes (AEMs) have been prepared by blending poly(vinyl alcohol) (PVA) and the random copolymer-type polycation, poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride) at various molar percentages of anion-exchange groups to vinyl alcohol groups, Cpc, and by cross-linking the PVA chains with glutaraldehyde (GA) solution at various GA concentrations, CGA. The characteristics of the random-type AEMs were compared with blend-type AEMs prepared in our previous study. At equal molar percentages of the anion exchange groups, the water content of the random-type AEMs was lower than that of the blend-type AEMs. The effective charge density of the random-type AEMs increased with increasing Cpc and reached a maximum value. Further, the maximum value of the effective charge density increased with increasing CGA. The maximum value of the effective charge density, 0.42 mol/dm3, was obtained for the random-type AEM with Cpc = 4.2 mol % and CGA = 0.15 vol %. A comparison of the random-type and blend-type AEMs with almost the same Cpc showed that the random-type AEMs had lower membrane resistance than the blend-type ones. The membrane resistance and dynamic transport number of the random-type AEM with Cpc = 6.0 mol % and CGA = 0.15 vol % were 4.8 Ω cm2 and 0.83, respectively.

Electrodialytic Transport Properties of Anion-Exchange Membranes Prepared from Poly(vinyl alcohol) and Poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride)

PubMed Central

Jikihara, Atsushi; Ohashi, Reina; Kakihana, Yuriko; Higa, Mitsuru; Kobayashi, Kenichi

2012-01-01

Random-type anion-exchange membranes (AEMs) have been prepared by blending poly(vinyl alcohol) (PVA) and the random copolymer-type polycation, poly(vinyl alcohol-co-methacryloyl aminopropyl trimethyl ammonium chloride) at various molar percentages of anion-exchange groups to vinyl alcohol groups, Cpc, and by cross-linking the PVA chains with glutaraldehyde (GA) solution at various GA concentrations, CGA. The characteristics of the random-type AEMs were compared with blend-type AEMs prepared in our previous study. At equal molar percentages of the anion exchange groups, the water content of the random-type AEMs was lower than that of the blend-type AEMs. The effective charge density of the random-type AEMs increased with increasing Cpc and reached a maximum value. Further, the maximum value of the effective charge density increased with increasing CGA. The maximum value of the effective charge density, 0.42 mol/dm3, was obtained for the random-type AEM with Cpc = 4.2 mol % and CGA = 0.15 vol %. A comparison of the random-type and blend-type AEMs with almost the same Cpc showed that the random-type AEMs had lower membrane resistance than the blend-type ones. The membrane resistance and dynamic transport number of the random-type AEM with Cpc = 6.0 mol % and CGA = 0.15 vol % were 4.8 Ω cm2 and 0.83, respectively. PMID:24958543

Comparative efficacy of two daily use mouthrinses: randomized clinical trial using an experimental gingivitis model.

PubMed

Charles, Christine Ann; McGuire, James Anthony; Sharma, Naresh Chandra; Qaqish, James

2011-01-01

Two antimicrobial agents, a fixed combination of essential oils (EOs) and 0.07% cetylpyridinium chloride (CPC) are found in commercially available mouthrinses, Listerine® Antiseptic and Crest® Pro HealthTM, respectively. Both mouthrinses have been shown to control dental plaque and gingivitis in short and longer term studies. The aim of this study was to determine the comparative effectiveness of these two mouthrinses using a 2-week experimental gingivitis model. Qualified subjects were randomly assigned to one of three mouthrinse groups: a fixed combination of EOs, 0.07% CPC, or negative control (C) rinse. Following baseline clinical assessments and a dental prophylaxis, subjects began a two-week period in which they rinsed twice daily with their assigned rinse and abstained from any mechanical oral hygiene procedures or other oral care products. Subjects were reassessed at the end of the two-week period. One hundred and forty-seven subjects were randomized and 142 completed this study. After two weeks use, the EOs rinse was superior (p < 0.011) to the CPC rinse in inhibiting the development of gingivitis, plaque, and bleeding, with 9.4% and 6.6% reductions compared to CPC for gingivitis and plaque, respectively. Both rinses were superior to the negative control rinse (p < 0.001). This study demonstrates that the essential oil-containing mouthrinse has superior antiplaque/antigingivitis effectiveness compared to the 0.07% CPC-containing mouthrinse without mechanical oral hygiene influence.

Polymorphic male color morphs visualized with steroids in monomorphic females: a tool for designing analysis of sex-limited trait inheritance.

PubMed

Olsson, Mats; Healey, Mo; Wilson, Mark; Tobler, Michael

2012-02-15

In diploid animals, males and females share most of the genome (except sex-specific elements, such as sex chromosome genes), yet despite sharing the underlying genes that hard-wire traits, males and females may differ in their phenotypes when traits are controlled by proximate mechanisms, such as hormones. In color polymorphic species where coloration is only expressed in one sex, the design of studies of the inheritance of color and coevolved morph-specific traits (e.g. territorial vs sneaker strategies, skewed energetic investment in territorial defense vs sperm production, etc.) is compromised as the expression of morph-coding genes is only visualized in one sex. Here, we circumvented this problem by first characterizing oxidative stress traits in both sexes and then using testosterone implants in females to expose their otherwise 'silent' coloration. Males of our model species are highly territorial and exhibit morph-specific levels of aggression, whereas females are non-territorial and display very low levels of aggression. Interestingly, reactive oxygen species levels were found to be morph specific regardless of sex, despite considerable differences in lifestyle. Males and females did differ remarkably, however, in superoxide levels depending on whether they sported a colored throat bib or not, a trait also used in male sexual signaling. Females with throat bibs had significantly lower levels of superoxide than females without a bib, which was not the case for males.

Comparative floral development in Lithospermum (Boraginaceae) and implications for the evolution and development of heterostyly.

PubMed

Cohen, James I; Litt, Amy; Davis, Jerrold I

2012-05-01

The evolution and development of floral developmental patterns were investigated in three heterostylous and three homostylous species of Lithospermum to determine whether species that independently acquired the same floral form follow the same pattern of development or different patterns. Using light and scanning electron microscopy, we observed developmental patterns in flowers at different stages of maturity. These patterns were compared within individual species, between heterostylous morphs, and among heterostylous and homostylous species. Although heterostyly has been determined by phylogenetic analysis to have originated independently in each of the heterostylous species, flowers of the long-style morph of each species follow similar patterns of gross development, as do those of the short-style morph. In addition, the flowers of each morph develop in a manner similar to those of their respective homostylous, herkogamous relatives. However, the developmental patterns of the stylar epidermal cells differ among these species and between heterostylous and homostylous species. Floral developmental patterns in homostylous species provide evidence that modification of specific traits, such as patterns of stylar growth, can lead to the evolution of heterostyly. The developmental changes that affect the positions of the stigmas and anthers in each morph likely involve either temporal or spatial modifications of gene function. The floral developmental patterns described here and the occurrence of multiple types of herkogamy within some species of Lithospermum provide evidence that heterostylous species in the genus have originated via distinct evolutionary developmental pathways.

The Effect of Diet Quality and Wing Morph on Male and Female Reproductive Investment in a Nuptial Feeding Ground Cricket

PubMed Central

Hall, Matthew D.; Bussière, Luc F.; Brooks, Robert

2008-01-01

A common approach in the study of life-history trade-off evolution is to manipulate the nutrient content of diets during the life of an individual in order observe how the acquisition of resources influences the relationship between reproduction, lifespan and other life-history parameters such as dispersal. Here, we manipulate the quality of diet that replicate laboratory populations received as a thorough test of how diet quality influences the life-history trade-offs associated with reproductive investment in a nuptial feeding Australian ground cricket (Pteronemobius sp.). In this species, both males and females make significant contributions to the production of offspring, as males provide a nuptial gift by allowing females to chew on a modified tibial spur during copulation and feed directing on their haemolymph. Individuals also have two distinct wing morphs, a short-winged flightless morph and a long-winged morph that has the ability to disperse. By manipulating the quality of diet over seven generations, we found that the reproductive investment of males and females were affected differently by the diet quality treatment and wing morph of the individual. We discuss the broader implications of these findings including the differences in how males and females balance current and future reproductive effort in nuptial feeding insects, the changing nature of sexual selection when diets vary, and how the life-history trade-offs associated with the ability to disperse are expected to differ among populations. PMID:18927614

Transfer to intermediate forms following concept discrimination by pigeons: chimeras and morphs.

PubMed Central

Ghosh, Natasha; Lea, Stephen E G; Noury, Malia

2004-01-01

Two experiments examined pigeons' generalization to intermediate forms following training of concept discriminations. In Experiment 1, the training stimuli were sets of images of dogs and cats, and the transfer stimuli were head/body chimeras, which humans tend to categorize more readily in terms of the head part rather than the body part. In Experiment 2, the training stimuli were sets of images of heads of dogs and cats, and the intermediate stimuli were computer-generated morphs. In both experiments, pigeons learned the concept discrimination quickly and generalized with some decrement to novel instances of the categories. In both experiments, transfer tests were carried out with intermediate forms generated from both familiar and novel exemplars of the training sets. In Experiment 1, the pigeons' transfer performance, unlike that of human infants exposed to similar stimuli, was best predicted by the body part of the stimulus when the chimeras were formed from familiar exemplars. Spatial frequency analysis of the stimuli showed that the body parts were richer in high spatial frequencies than the head parts, so these data are consistent with the hypothesis that categorization is more dependent on local stimulus features in pigeons than in humans. There was no corresponding trend when the chimeras were formed from novel exemplars. In Experiment 2, when morphs of training stimuli were used, response rates declined smoothly as the proportion of the morph contributed by the positive stimulus fell, although results with morphs of novel stimuli were again less orderly. PMID:15540501

Updating impairments and the failure to explore new hypotheses following right brain damage.

PubMed

Stöttinger, Elisabeth; Guay, Carolyn Louise; Danckert, James; Anderson, Britt

2018-06-01

We have shown recently that damage to the right hemisphere impairs the ability to update mental models when evidence suggests an old model is no longer appropriate. We argue that this deficit is generic in the sense that it crosses multiple cognitive and perceptual domains. Here, we examined the nature of this updating impairment to determine more precisely the underlying mechanisms. We had right (RBD, N = 12) and left brain damaged (LBD, N = 10) patients perform versions of our picture-morphing task in which pictures gradually morph from one object (e.g., shark) to another (e.g., plane). Performance was contrasted against two groups of healthy older controls, one matched on age (HCO-age-matched, N = 9) and another matched on general level of cognitive ability (HCO-cognitively-matched, N = 9). We replicated our earlier findings showing that RBD patients took longer than LBD patients and HCOs to report seeing the second object in a sequence of morphing images. The groups did not differ when exposed to a morphing sequence a second time, or when responding to ambiguous images outside the morphing context. This indicates that RBD patients have little difficulty alternating between known representations or labeling ambiguous images. Instead, the difficulty lies in generating alternate hypotheses for ambiguous information. Lesion overlay analyses, although speculative given the sample size, are consistent with our fMRI work in healthy individuals in implicating the anterior insular cortex as critical for updating mental models.

Inherited variants in the inner centromere protein (INCENP) gene of the chromosomal passenger complex contribute to the susceptibility of ER-negative breast cancer

PubMed Central

Kabisch, Maria; Lorenzo Bermejo, Justo; Dünnebier, Thomas; Ying, Shibo; Michailidou, Kyriaki; Bolla, Manjeet K.; Wang, Qin; Dennis, Joe; Shah, Mitul; Perkins, Barbara J.; Czene, Kamila; Darabi, Hatef; Eriksson, Mikael; Bojesen, Stig E.; Nordestgaard, Børge G.; Nielsen, Sune F.; Flyger, Henrik; Lambrechts, Diether; Neven, Patrick; Peeters, Stephanie; Weltens, Caroline; Couch, Fergus J.; Olson, Janet E.; Wang, Xianshu; Purrington, Kristen; Chang-Claude, Jenny; Rudolph, Anja; Seibold, Petra; Flesch-Janys, Dieter; Peto, Julian; dos-Santos-Silva, Isabel; Johnson, Nichola; Fletcher, Olivia; Nevanlinna, Heli; Muranen, Taru A.; Aittomäki, Kristiina; Blomqvist, Carl; Schmidt, Marjanka K.; Broeks, Annegien; Cornelissen, Sten; Hogervorst, Frans B.L.; Li, Jingmei; Brand, Judith S.; Humphreys, Keith; Guénel, Pascal; Truong, Thérèse; Menegaux, Florence; Sanchez, Marie; Burwinkel, Barbara; Marmé, Frederik; Yang, Rongxi; Bugert, Peter; González-Neira, Anna; Benitez, Javier; Pilar Zamora, M.; Arias Perez, Jose I.; Cox, Angela; Cross, Simon S.; Reed, Malcolm W.R.; Andrulis, Irene L.; Knight, Julia A.; Glendon, Gord; Tchatchou, Sandrine; Sawyer, Elinor J.; Tomlinson, Ian; Kerin, Michael J.; Miller, Nicola; Haiman, Christopher A.; Schumacher, Fredrick; Henderson, Brian E.; Le Marchand, Loic; Lindblom, Annika; Margolin, Sara; Hooning, Maartje J.; Hollestelle, Antoinette; Kriege, Mieke; Koppert, Linetta B.; Hopper, John L.; Southey, Melissa C.; Tsimiklis, Helen; Apicella, Carmel; Slettedahl, Seth; Toland, Amanda E.; Vachon, Celine; Yannoukakos, Drakoulis; Giles, Graham G.; Milne, Roger L.; McLean, Catriona; Fasching, Peter A.; Ruebner, Matthias; Ekici, Arif B.; Beckmann, Matthias W.; Brenner, Hermann; Dieffenbach, Aida K.; Arndt, Volker; Stegmaier, Christa; Ashworth, Alan; Orr, Nicholas; Schoemaker, Minouk J.; Swerdlow, Anthony; García-Closas, Montserrat; Figueroa, Jonine; Chanock, Stephen J.; Lissowska, Jolanta; Goldberg, Mark S.; Labrèche, France; Dumont, Martine; Winqvist, Robert; Pylkäs, Katri; Jukkola-Vuorinen, Arja; Grip, Mervi; Brauch, Hiltrud; Brüning, Thomas; Ko, Yon-Dschun; Radice, Paolo; Peterlongo, Paolo; Scuvera, Giulietta; Fortuzzi, Stefano; Bogdanova, Natalia; Dörk, Thilo; Mannermaa, Arto; Kataja, Vesa; Kosma, Veli-Matti; Hartikainen, Jaana M.; Devilee, Peter; Tollenaar, Robert A.E.M.; Seynaeve, Caroline; Van Asperen, Christi J.; Jakubowska, Anna; Lubinski, Jan; Jaworska-Bieniek, Katarzyna; Durda, Katarzyna; Zheng, Wei; Shrubsole, Martha J.; Cai, Qiuyin; Torres, Diana; Anton-Culver, Hoda; Kristensen, Vessela; Bacot, François; Tessier, Daniel C.; Vincent, Daniel; Luccarini, Craig; Baynes, Caroline; Ahmed, Shahana; Maranian, Mel; Simard, Jacques; Chenevix-Trench, Georgia; Hall, Per; Pharoah, Paul D.P.; Dunning, Alison M.; Easton, Douglas F.; Hamann, Ute

2015-01-01

The chromosomal passenger complex (CPC) plays a pivotal role in the regulation of cell division. Therefore, inherited CPC variability could influence tumor development. The present candidate gene approach investigates the relationship between single nucleotide polymorphisms (SNPs) in genes encoding key CPC components and breast cancer risk. Fifteen SNPs in four CPC genes (INCENP, AURKB, BIRC5 and CDCA8) were genotyped in 88 911 European women from 39 case-control studies of the Breast Cancer Association Consortium. Possible associations were investigated in fixed-effects meta-analyses. The synonymous SNP rs1675126 in exon 7 of INCENP was associated with overall breast cancer risk [per A allele odds ratio (OR) 0.95, 95% confidence interval (CI) 0.92–0.98, P = 0.007] and particularly with estrogen receptor (ER)-negative breast tumors (per A allele OR 0.89, 95% CI 0.83–0.95, P = 0.0005). SNPs not directly genotyped were imputed based on 1000 Genomes. The SNPs rs1047739 in the 3ʹ untranslated region and rs144045115 downstream of INCENP showed the strongest association signals for overall (per T allele OR 1.03, 95% CI 1.00–1.06, P = 0.0009) and ER-negative breast cancer risk (per A allele OR 1.06, 95% CI 1.02–1.10, P = 0.0002). Two genotyped SNPs in BIRC5 were associated with familial breast cancer risk (top SNP rs2071214: per G allele OR 1.12, 95% CI 1.04–1.21, P = 0.002). The data suggest that INCENP in the CPC pathway contributes to ER-negative breast cancer susceptibility in the European population. In spite of a modest contribution of CPC-inherited variants to the total burden of sporadic and familial breast cancer, their potential as novel targets for breast cancer treatment should be further investigated. PMID:25586992

Phototrophic cultivation of NaCl-tolerant mutant of Spirulina platensis for enhanced C-phycocyanin production under optimized culture conditions and its dynamic modeling.

PubMed

Gupta, Apurva; Mohan, Devendra; Saxena, Rishi Kumar; Singh, Surendra

2018-02-01

Commercial cultivation of Spirulina sp. is highly popular due to the presence of high amount of C-phycocyanin (C-PC) and other valuable chemicals like carotenoids and γ-linolenic acid. In this study, the pH and the concentrations of nitrogen and carbon source were manipulated to achieve improved cell growth and C-PC production in NaCl-tolerant mutant of Spirulina platensis. In this study, highest C-PC (147 mg · L -1 ) and biomass (2.83 g · L -1 ) production was achieved when a NaCl-tolerant mutant of S. platensis was cultivated in a nitrate and bicarbonate sufficient medium (40 and 60 mM, respectively) at pH 9.0 under phototrophic conditions. Kinetic study of wildtype S. platensis and its NaCl-tolerant mutant was also done to determine optimum nitrate concentrations for maximum growth and C-PC production. Kinetic parameter of inhibition (Haldane model) was fitted to the relationship between specific growth rate and substrate concentration obtained from the growth curves. Results showed that the maximum specific growth rate (μ max ) for NaCl-tolerant mutant increased by 17.94% as compared to its wildtype counterpart, with a slight increase in half-saturation constant (K s ), indicating that this strain could grow well at high concentration of NaNO 3 . C-PC production rate (C max ) in mutant cells increased by 12.2% at almost half the value of K s as compared to its wildtype counterpart. Moreover, the inhibition constant (K i ) value was 207.85% higher in NaCl-tolerant mutant as compared to its wildtype strain, suggesting its ability to produce C-PC even at high concentrations of NaNO 3 . © 2017 Phycological Society of America.

Inherited variants in the inner centromere protein (INCENP) gene of the chromosomal passenger complex contribute to the susceptibility of ER-negative breast cancer.

PubMed

Kabisch, Maria; Lorenzo Bermejo, Justo; Dünnebier, Thomas; Ying, Shibo; Michailidou, Kyriaki; Bolla, Manjeet K; Wang, Qin; Dennis, Joe; Shah, Mitul; Perkins, Barbara J; Czene, Kamila; Darabi, Hatef; Eriksson, Mikael; Bojesen, Stig E; Nordestgaard, Børge G; Nielsen, Sune F; Flyger, Henrik; Lambrechts, Diether; Neven, Patrick; Peeters, Stephanie; Weltens, Caroline; Couch, Fergus J; Olson, Janet E; Wang, Xianshu; Purrington, Kristen; Chang-Claude, Jenny; Rudolph, Anja; Seibold, Petra; Flesch-Janys, Dieter; Peto, Julian; dos-Santos-Silva, Isabel; Johnson, Nichola; Fletcher, Olivia; Nevanlinna, Heli; Muranen, Taru A; Aittomäki, Kristiina; Blomqvist, Carl; Schmidt, Marjanka K; Broeks, Annegien; Cornelissen, Sten; Hogervorst, Frans B L; Li, Jingmei; Brand, Judith S; Humphreys, Keith; Guénel, Pascal; Truong, Thérèse; Menegaux, Florence; Sanchez, Marie; Burwinkel, Barbara; Marmé, Frederik; Yang, Rongxi; Bugert, Peter; González-Neira, Anna; Benitez, Javier; Pilar Zamora, M; Arias Perez, Jose I; Cox, Angela; Cross, Simon S; Reed, Malcolm W R; Andrulis, Irene L; Knight, Julia A; Glendon, Gord; Tchatchou, Sandrine; Sawyer, Elinor J; Tomlinson, Ian; Kerin, Michael J; Miller, Nicola; Haiman, Christopher A; Schumacher, Fredrick; Henderson, Brian E; Le Marchand, Loic; Lindblom, Annika; Margolin, Sara; Hooning, Maartje J; Hollestelle, Antoinette; Kriege, Mieke; Koppert, Linetta B; Hopper, John L; Southey, Melissa C; Tsimiklis, Helen; Apicella, Carmel; Slettedahl, Seth; Toland, Amanda E; Vachon, Celine; Yannoukakos, Drakoulis; Giles, Graham G; Milne, Roger L; McLean, Catriona; Fasching, Peter A; Ruebner, Matthias; Ekici, Arif B; Beckmann, Matthias W; Brenner, Hermann; Dieffenbach, Aida K; Arndt, Volker; Stegmaier, Christa; Ashworth, Alan; Orr, Nicholas; Schoemaker, Minouk J; Swerdlow, Anthony; García-Closas, Montserrat; Figueroa, Jonine; Chanock, Stephen J; Lissowska, Jolanta; Goldberg, Mark S; Labrèche, France; Dumont, Martine; Winqvist, Robert; Pylkäs, Katri; Jukkola-Vuorinen, Arja; Grip, Mervi; Brauch, Hiltrud; Brüning, Thomas; Ko, Yon-Dschun; Radice, Paolo; Peterlongo, Paolo; Scuvera, Giulietta; Fortuzzi, Stefano; Bogdanova, Natalia; Dörk, Thilo; Mannermaa, Arto; Kataja, Vesa; Kosma, Veli-Matti; Hartikainen, Jaana M; Devilee, Peter; Tollenaar, Robert A E M; Seynaeve, Caroline; Van Asperen, Christi J; Jakubowska, Anna; Lubinski, Jan; Jaworska-Bieniek, Katarzyna; Durda, Katarzyna; Zheng, Wei; Shrubsole, Martha J; Cai, Qiuyin; Torres, Diana; Anton-Culver, Hoda; Kristensen, Vessela; Bacot, François; Tessier, Daniel C; Vincent, Daniel; Luccarini, Craig; Baynes, Caroline; Ahmed, Shahana; Maranian, Mel; Simard, Jacques; Chenevix-Trench, Georgia; Hall, Per; Pharoah, Paul D P; Dunning, Alison M; Easton, Douglas F; Hamann, Ute

2015-02-01

The chromosomal passenger complex (CPC) plays a pivotal role in the regulation of cell division. Therefore, inherited CPC variability could influence tumor development. The present candidate gene approach investigates the relationship between single nucleotide polymorphisms (SNPs) in genes encoding key CPC components and breast cancer risk. Fifteen SNPs in four CPC genes (INCENP, AURKB, BIRC5 and CDCA8) were genotyped in 88 911 European women from 39 case-control studies of the Breast Cancer Association Consortium. Possible associations were investigated in fixed-effects meta-analyses. The synonymous SNP rs1675126 in exon 7 of INCENP was associated with overall breast cancer risk [per A allele odds ratio (OR) 0.95, 95% confidence interval (CI) 0.92-0.98, P = 0.007] and particularly with estrogen receptor (ER)-negative breast tumors (per A allele OR 0.89, 95% CI 0.83-0.95, P = 0.0005). SNPs not directly genotyped were imputed based on 1000 Genomes. The SNPs rs1047739 in the 3' untranslated region and rs144045115 downstream of INCENP showed the strongest association signals for overall (per T allele OR 1.03, 95% CI 1.00-1.06, P = 0.0009) and ER-negative breast cancer risk (per A allele OR 1.06, 95% CI 1.02-1.10, P = 0.0002). Two genotyped SNPs in BIRC5 were associated with familial breast cancer risk (top SNP rs2071214: per G allele OR 1.12, 95% CI 1.04-1.21, P = 0.002). The data suggest that INCENP in the CPC pathway contributes to ER-negative breast cancer susceptibility in the European population. In spite of a modest contribution of CPC-inherited variants to the total burden of sporadic and familial breast cancer, their potential as novel targets for breast cancer treatment should be further investigated. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

[Mild therapeutic hypothermia in cardiogenic shock : Retrospective analysis of 80 patients with preclinical cardiac arrest due to cardiac causes].

PubMed

Adler, C; Pfister, R; Baldus, S; Reuter, H

2017-02-01

The mortality in patients with cardiogenic shock after out-of-hospital cardiac arrest (OHCA) remains high despite advances in resuscitation and early revascularization strategies. The use of mild therapeutic hypothermia (MTH) for improvement of survival and neurological outcome in patients with cardiogenic shock is currently subject to renewed discussion. The aim of this study was the detection of risk factors for mortality and morbidity in patients under MTH in cardiogenic shock following preclinical resuscitation for OHCA. A total of 80 consecutive patients in cardiogenic shock after successful resuscitation (mean age 60 ± 3.2 years) treated with MTH were retrospectively analyzed. Patients were cooled to 33 °C for 24 h using an endovascular cooling device. Neurological outcome was assessed after 2 months based on the Glasgow-Pittsburgh cerebral performance category (CPC) and correlated with various blood parameter values. After 2 months 31 patients (39 %) showed a good neurological recovery with CPC scores of 1-2, 20 patients (25 %) had a poor neurological outcome with CPC scores of 3-4 and 29 (36 %) patients enrolled in the trial died (CPC 5). Patients with a poor outcome showed significantly higher mean serum levels for lactate, creatinine and urea. In addition, these patients showed a continuous increase of serum neuron-specific enolase (NSE) values in contrast to patients with a good outcome (∆ NSE from admission to day 1, CPC 1 and 2: - 10.6 ± 3 µg/l and CPC 3-5: 33 ± 12 µg/l, p = 0.02). Changes in the course of serum creatinine, urea and NSE levels within the first 72 h after OHCA could provide valuable additional information for the early assessment of the neurological prognosis in patients treated with MTH.

Coupled behavior of shape memory alloy-based morphing spacecraft radiators: experimental assessment and analysis

NASA Astrophysics Data System (ADS)

Bertagne, C.; Walgren, P.; Erickson, L.; Sheth, R.; Whitcomb, J.; Hartl, D.

2018-06-01

Thermal control is an important aspect of spacecraft design, particularly in the case of crewed vehicles, which must maintain a precise internal temperature at all times in spite of significant variations in the external thermal environment and internal heat loads. Future missions beyond low Earth orbit will require radiator systems with high turndown ratios, defined as the ratio between the maximum and minimum heat rejection rates achievable by the radiator system. Current radiators are only able to achieve turndown ratios of 3:1, far less than the 12:1 turndown ratio requirement expected for future missions. An innovative morphing radiator concept uses the temperature-induced phase transformation of shape memory alloy (SMA) materials to achieve turndown ratios that are predicted to exceed 12:1 via substantial geometric reconfiguration. Developing mathematical and computational models of these morphing radiators is challenging due to the strong two-way thermomechanical coupling not present in traditional fixed-geometry radiators and not widely considered in the literature. Although existing simulation tools are capable of analyzing the behavior of some thermomechanically coupled structures, general problems involving radiation and deformation cannot be modeled using publicly available codes due to the complexity of modeling spatially evolving boundary fields. This paper provides important insight into the operational response of SMA-based morphing radiators by employing computational tools developed to overcome previous shortcomings. Several example problems are used to demonstrate the novel radiator concept. Additionally, a prototype morphing radiator was designed, fabricated, and tested in a thermal environment compatible with mission operations. An associated finite element model of the prototype was developed and executed. Model predictions of radiator performance generally agree with the experimental data, giving confidence that the tools developed are able to accurately represent the thermomechanical coupling present in morphing radiators and that such tools will be useful in future designs.

Aerostructural optimization of a morphing wing for airborne wind energy applications

NASA Astrophysics Data System (ADS)

Fasel, U.; Keidel, D.; Molinari, G.; Ermanni, P.

2017-09-01

Airborne wind energy (AWE) vehicles maximize energy production by constantly operating at extreme wing loading, permitted by high flight speeds. Additionally, the wide range of wind speeds and the presence of flow inhomogeneities and gusts create a complex and demanding flight environment for AWE systems. Adaptation to different flow conditions is normally achieved by conventional wing control surfaces and, in case of ground generator-based systems, by varying the reel-out speed. These control degrees of freedom enable to remain within the operational envelope, but cause significant penalties in terms of energy output. A significantly greater adaptability is offered by shape-morphing wings, which have the potential to achieve optimal performance at different flight conditions by tailoring their airfoil shape and lift distribution at different levels along the wingspan. Hence, the application of compliant structures for AWE wings is very promising. Furthermore, active gust load alleviation can be achieved through morphing, which leads to a lower weight and an expanded flight envelope, thus increasing the power production of the AWE system. This work presents a procedure to concurrently optimize the aerodynamic shape, compliant structure, and composite layup of a morphing wing for AWE applications. The morphing concept is based on distributed compliance ribs, actuated by electromechanical linear actuators, guiding the deformation of the flexible—yet load-carrying—composite skin. The goal of the aerostructural optimization is formulated as a high-level requirement, namely to maximize the average annual power production per wing area of an AWE system by tailoring the shape of the wing, and to extend the flight envelope of the wing by actively alleviating gust loads. The results of the concurrent multidisciplinary optimization show a 50.7% increase of extracted power with respect to a sequentially optimized design, highlighting the benefits of morphing and the potential of the proposed approach.

A proteomic approach to the analysis of the components of the phycobilisomes from two cyanobacteria with complementary chromatic adaptation: Fremyella diplosiphon UTEX B590 and Tolypothrix PCC 7601.

PubMed

Pérez-Gómez, Bertha; Mendoza-Hernández, Guillermo; Cabellos-Avelar, Tecilli; Leyva-Castillo, Lourdes Elizabeth; Gutiérrez-Cirlos, Emma Berta; Gómez-Lojero, Carlos

2012-10-01

Tolypothrix PCC 7601 and Fremyella diplosiphon UTEX B590 can produce two alternative phycobilisome (PBS) rods. PE-PBSs with one phycocyanin (PC) disk and multiple phycoerythrin (PE) disks are found in cells grown under green light (GL). PC-PBSs with only PC disks are obtained from cells grown under red light (RL). In this manuscript, we show the localization of the linker proteins and ferredoxin-NADP(+) oxidoreductase (FNR) in the PC-PBS and of PE-PBS rods using visible spectroscopy and mass spectrometry. PE-PBSs with different [PE]/[PC] ratios and PC-PBSs with different [PC]/[AP] (AP, allophycocyanin) ratios were isolated. CpeC was the primary rod linker protein found in the PBSs with a [PE]/[PC] ratio of 1.1, which indicates that this is the rod linker at the interphase PC-PE. CpeC and CpeD were identified in the PBSs with a [PE]/[PC] ratio of 1.6, which indicates that CpcD is the linker between the first and the second PE hexamers. Finally, CpeC, CpeD, and CpeE were found in the PBSs with a [PE]/[PC] ratio of 2.9, indicating the position of CpeE between the second and third PE moieties. CpcI2 was identified in the two PC-PBSs obtained from cells grown under RL, which indicates that CpcI2 is the linker between the first and second PC hexamers. CpcH2 was identified only in the PC-PBSs from Tolypothrix with a high [PC]/[AP] ratio of 1.92, which indicates that CpcH2 is the linker between the second and third PC hexamers. The PC-PBSs contained the rod cap protein L(R)(10) (CpcD), but this protein was absent in the PE-PBSs. PE-PBSs (lacking L(R)(10)) incorporated exogenous rFNR in a stoichiometry of up to five FNRs per PBS. A maximum of two FNRs per PBS were found in PC-PBSs (with L(R)(10)). These observations support the hypothesis that FNR binds at the distal ends of the PBS rods in the vacant site of CpcD L(R)(10). Finally, the molecular mass of the core membrane linker (L(CM)) was determined to be 102 kDa from a mass spectrometry analysis.

SU-E-J-67: Evaluation of Adaptive MLC Morphing for Online Correction of Prostate Cancer Radiotherapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandhu, R; Qin, A; Yan, D

Purpose: Online adaptive MLC morphing is desirable over translational couch shifts to accommodate target position as well as anatomic changes. A reliable method of adaptive MLC segment to target during prostate cancer IMRT treatment is proposed and evaluated by comparison with daily online-image guidance (IGRT) correction and online-IMRT planning. Methods: The MLC adaptive algorithm involves following steps; move the MLC segments according to target translational shifts, and then morph the segment shape to maintain the spatial relationship between the planning-target contour and MLC segment. Efficacy of this method was evaluated retrospectively using daily-CBCT images on seven prostate patients treated withmore » seven-beam IMRT treatment to deliver 64Gy in 20 fractions. Daily modification was simulated with three approaches; daily-IGRT correction based on implanted radio-markers, adaptive MLC morphing, and online-IMRT planning, with no-residual variation. The selected dosimetric endpoints and nEUD (normalized equivalent uniform dose to online-IMRT planning) of each organ of interest were determined for evaluation and comparison. Results: For target(prostate), bladder and rectal-wall, the mean±sd of nEUD were 97.6%+3.2%, 103.9%±4.9% and 97.4%±1.1% for daily-IGRT correction; and 100.2%+0.2%, 108.9%±5.1% and 99.8%±1.2% for adaptive MLC morphing, respectively. For daily-IGRT correction, adaptive MLC morphing and online-IMRT planning, target D99 was <95% of the prescription dose in 30%, 0% and 0% of 140 fractions, respectively. For the rectal-wall, D5 exceeded 105% of the planned-D5 in 2.8%, 11.4% and 0% of 140 fractions, respectively. For the bladder, Dmax exceeded 105% of the planned-D5 in 2.8%, 5.6% and 0% of 140 fractions, respectively. D30 of bladder and rectal-wall were well within the planned-D30 for all three approaches. Conclusion: The proposed method of adaptive MLC morphing can be beneficial for the prostate patient population with large deformation and rotation. It is superior to the daily-IGRT correction, and comparable to the online-IMRT planning for dose to the target and rectal-wall.« less