Feasibility of reclaimed asphalt pavement as aggregate in portland cement concrete pavement, phase II : field demonstration.

DOT National Transportation Integrated Search

2015-10-01

This research was focused on evaluating the feasibility of using minimally processed reclaimed asphalt pavement (RAP) as : aggregate replacement in concrete pavements. An initial phase of research demonstrated that concretes with up to 50 percent : o...

Asphaltic concrete overlays of rigid and flexible pavements

NASA Astrophysics Data System (ADS)

Kinchen, R. W.; Temple, W. H.

1980-10-01

The development of a mechanistic approach to overlay thickness selection is described. The procedure utilizes a deflection analysis to determine pavement rehabilitation needs. Design guides for selecting the overlay thickness are presented. Tolerable deflection-traffic load relationships and the deflection attenuation properties of asphaltic concrete were developed, representing the subgrade support conditions and properties of materials used in Louisiana. All deflection measurements on asphaltic concrete were corrected for the effect of temperature. Deflection measurements taken before and after overlay were also adjusted to minimize the effects of seasonal subgrade moisture variation.

Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays

NASA Astrophysics Data System (ADS)

Jaskula, P.; Szydlowski, C.; Stienss, M.

2018-05-01

Cracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One factor that minimizes this type of distress is the proper mix design process, which should involve selection of specific bitumen binder and mineral mix gradation. However, still there is no universally adopted laboratory test method that would allow to clearly assess resistance of asphalt mixtures to reflective cracking. This paper describes the usage of one of the devices developed to test asphalt mixtures in terms of such distress – Texas Overlay Tester. For this test, samples prepared in laboratory conditions (i.e. compacted with the use of Superpave Gyratory Compactor) as well as obtained in the field (by core drilling) can be used. The results are obtained not only quickly and easily, but also with sufficient repeatability. The described method characterizes both crack initiation and crack propagation properties of asphalt mixtures. In this work one type of mineral mixture was tested with 4 different types of bitumen (one neat bitumen, two ordinary polymer-modified and one polymer-modified with high polymer content). For selected cases extra additives (rubber and loose fibres) were also tested. In total, six asphalt mixtures were tested. A ranking of the used binders was created on the basis of the results in order to conclude which bitumen would ensure the best performance characteristics in terms of reflective cracking. The results have clearly shown that deliberate choice of the binder used in the asphalt mixture for the overlay will significantly improve its reflective cracking resistance or even fatigue resistance.

Assessment of asphalt interlayer designed on jointed concrete.

DOT National Transportation Integrated Search

2014-11-01

Reflective cracking in hot mix asphalt (HMA) overlays has been a common cause of poor pavement performance in Iowa for : many years. Reflective cracks commonly occur in HMA overlays when deteriorated portland cement concrete is paved over with : HMA....

Fatigue and Fracture Characterization of GlasGridRTM Reinforced Asphalt Concrete Pavement

NASA Astrophysics Data System (ADS)

Safavizadeh, Seyed Amirshayan

The purpose of this research is to develop an experimental and analytical framework for describing, modeling, and predicting the reflective cracking patterns and crack growth rates in GlasGridRTM-reinforced asphalt pavements. In order to fulfill this objective, the effects of different interfacial conditions (mixture and tack coat type, and grid opening size) on reflective cracking-related failure mechanisms and the fatigue and fracture characteristics of fiberglass grid-reinforced asphalt concrete beams were studied by means of four- and threepoint bending notched beam fatigue tests (NBFTs) and cyclic and monotonic interface shear tests. The digital image correlation (DIC) technique was utilized for obtaining the displacement and strain contours of specimen surfaces during each test. The DIC analysis results were used to develop crack tip detection methods that were in turn used to determine interfacial crack lengths in the shear tests, and vertical and horizontal (interfacial) crack lengths in the notched beam fatigue tests. Linear elastic fracture mechanics (LEFM) principles were applied to the crack length data to describe the crack growth. In the case of the NBFTs, a finite element (FE) code was developed and used for modeling each beam at different stages of testing and back-calculating the stress intensity factors (SIFs) for the vertical and horizontal cracks. The local effect of reinforcement on the stiffness of the system at a vertical crack-interface intersection or the resistance of the grid system to the deflection differential at the joint/crack (hereinafter called joint stiffness) for GlasGrid-reinforced asphalt concrete beams was determined by implementing a joint stiffness parameter into the finite element code. The strain level dependency of the fatigue and fracture characteristics of the GlasGrid-reinforced beams was studied by performing four-point bending notched beam fatigue tests at strain levels of 600, 750, and 900 microstrain. These beam

Density measurement verification for hot mixed asphalt concrete pavement construction.

DOT National Transportation Integrated Search

2010-06-01

Oregon Department of Transportation (ODOT) requires a minimum density for the construction of dense-graded hot mix asphalt concrete (HMAC) pavements to ensure the likelihood that the pavement will not experience distresses that reduce the expected se...

Density measurement verification for hot mix asphalt concrete pavement construction.

DOT National Transportation Integrated Search

2010-06-01

Oregon Department of Transportation (ODOT) requires a minimum density for the construction of dense-graded hot mix asphalt concrete (HMAC) pavements to ensure the likelihood that the pavement will not experience distresses that reduce the expected se...

Aggregate Toughness/Abrasion Resistance and Durability/Soundness Tests Related to Asphalt Concrete Performance in Pavements

DOT National Transportation Integrated Search

1998-03-01

The properties of aggregates used in asphalt concretes are very important to the performance of the pavements in which the asphalt concretes are used. Often pavement distress, such as stripping and rutting, can be traced directly to the aggregates us...

Research notes : geotextile fabrics under asphalt concrete overlays.

DOT National Transportation Integrated Search

1992-12-01

Last year, the City of Portland decided to place geotextile fabrics under asphalt concrete overlays for pavement reinforcement and crack retardation. The City expected the following benefits from using the fabrics: retardation of reflective cracks, r...

Evaluation of full depth asphaltic concrete pavements : interim report.

DOT National Transportation Integrated Search

1975-02-01

This report provides a review of the performance and structural characteristics exhibited on two full depth asphaltic concrete pavement projects constructed on the Louisiana interstate system. : The roughness characteristics of both full depth projec...

Improved overlay tester for fatigue cracking resistance of asphalt mixtures.

DOT National Transportation Integrated Search

2017-01-01

Premature cracking of the asphalt concrete (AC) layer in flexible pavement is one of the major concerns of the pavement community. Over the past decade, AC mixes have been designed using the Hamburg wheel-tracking device to improve their rutting pote...

Stress Regression Analysis of Asphalt Concrete Deck Pavement Based on Orthogonal Experimental Design and Interlayer Contact

NASA Astrophysics Data System (ADS)

Wang, Xuntao; Feng, Jianhu; Wang, Hu; Hong, Shidi; Zheng, Supei

2018-03-01

A three-dimensional finite element box girder bridge and its asphalt concrete deck pavement were established by ANSYS software, and the interlayer bonding condition of asphalt concrete deck pavement was assumed to be contact bonding condition. Orthogonal experimental design is used to arrange the testing plans of material parameters, and an evaluation of the effect of different material parameters in the mechanical response of asphalt concrete surface layer was conducted by multiple linear regression model and using the results from the finite element analysis. Results indicated that stress regression equations can well predict the stress of the asphalt concrete surface layer, and elastic modulus of waterproof layer has a significant influence on stress values of asphalt concrete surface layer.

Laboratory evaluation of asphalt concrete mixtures containing high contents of reclaimed asphalt pavement (RAP) and binder.

DOT National Transportation Integrated Search

2014-11-01

This study investigated the effect of added asphalt : binder content on the performance and volumetric p : roperties of : asphalt concrete mixtures containing reclaimed asph : alt pavement (RAP) in the amounts of 0%, 20%, and 4 : 0%. A laboratory- : ...

Criteria for asphalt-rubber concrete in civil airport pavements: Mixture design

NASA Astrophysics Data System (ADS)

Roberts, F. L.; Lytton, R. L.; Hoyt, D.

1986-07-01

A mixture design procedure is developed to allow the use of asphalt-rubber binders in concrete for flexible airport pavement. The asphalt-rubber is produced by reacting asphalt with ground, scrap tire rubber to produce the binder for the asphalt-rubber concrete. Procedures for laboratory preparation of alsphalt-rubber binders using an equipment setup that was found by researchers to produce laboratory binders with similar properties to field processes are included. The rubber-asphalt concrete mixture design procedure includes adjustments to the aggregate gradation to permit space for the rubber particles in the asphalt-rubber binder as well as suggested mixing and compaction temperatures, and compaction efforts. While the procedure was used in the laboratory to successfully produce asphalt-rubber concrete mixtures, it should be evaluated in the field to ensure that consistent results can be achieved in a production environment.

Analysis of Cracking in Jointed Plain Concrete Pavements

DOT National Transportation Integrated Search

2017-03-01

This paper investigates the trends of longitudinal and transverse cracking in jointed concrete pavements based on Long-Term Pavement Performance (LTPP) Program Strategic Study of Structural Factors for Rigid Pavements (SPS-2) data. The impacts of sla...

Deicer usage on concrete and asphalt pavements in Utah.

DOT National Transportation Integrated Search

2014-06-01

The objectives of this research were to 1) compile winter maintenance data for the Utah Department of : Transportation (UDOT) to directly compare concrete and asphalt pavements with regards to deicer usage and 2) : determine if there is a statistical...

Performance of rehabilitated asphalt concrete pavements in LTPP experiments (data collected through February 1997).

DOT National Transportation Integrated Search

2000-06-01

Two experiments are included within the Long Term Pavement Performance (LTPP) program to provide data on the performance of : rehabilitated asphalt concrete (AC) pavements. These two experiments include Specific Pavement Studies No. 5 (SPS-5) and Gen...

A case study : early cracking of unreinforced concrete pavement.

DOT National Transportation Integrated Search

1973-01-01

A study of cores from both the concrete and subbase of the cracked pavement, along with an examination of the in-place subgrade and subbase, suggested that there was no structural damage to the pavement except for the cracking. The situation was aggr...

Tolerable strains for hot mix asphalt overlays over concrete pavements.

DOT National Transportation Integrated Search

2013-01-01

Due to change of temperature and/or moisture, freezing-thaw cycles, loss of subgrade support by erosion, and traffic loading, concrete : pavements can develop different types of distresses during service life. Hot mix asphalt (HMA) overlays are commo...

Asphalt concrete properties and performance in Alaska : executive summary

DOT National Transportation Integrated Search

1982-01-01

A major study of asphalt concrete properties and performance of Alaska's highways was completed in 1982. The project data base was obtained from 117 statewide pavement sections through numerous core samples and measurements of cracking, patching and ...

Adjusting Asphalt Mixes for Increased Durability and Implementation of a Performance Tester to Evaluate Fatigue Cracking of Asphalt

DOT National Transportation Integrated Search

2018-01-17

Cracking is a common failure mechanism in asphalt concrete pavement structures. It is one of the main reasons for large road maintenance and rehabilitation expenditures, as well as reduced user comfort and increased fuel consumption due to high road ...

Comparison of wintertime asphalt and concrete pavement surface temperatures on U.S. Route 40 near Heber, Utah.

DOT National Transportation Integrated Search

2014-06-01

Asphalt and concrete pavement surface temperatures were compared at a location on U.S. Route 40 in : northern Utah where asphalt and concrete meet end to end at the base of the mountain pass. An environmental : sensor station was installed to facilit...

Asphalt pavement surfaces and asphalt mixtures. Transportation research record

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-31

The papers in this volume, which deal with asphalt pavement surfaces and asphalt mixtures, should be of interest to state and local construction, design, materials, and research engineers as well as contractors and material producers. The papers in Part 1 include discussions of pavement smoothness specifications and skidding characteristics. The first four papers in Part 2 were submitted in response to a call for papers for a session at the 75th Annual Meeting of the Transportation Research Board on low-temperature properties of hot-mix asphalt. The next eight are on the influence of volumetric and strength properties on the performance ofmore » hot-mix asphalt. In the following three papers, the topics covered are the complex modulus of asphalt concrete, cold in-place asphalt recycling, and polymer modification of asphalt pavements in Ontario. The last two papers were presented in a session on relationship of materials characterization to accelerated pavement performance testing.« less

Correlation of construction quality criteria with performance of asphaltic concrete pavements : final report.

DOT National Transportation Integrated Search

1987-08-01

This report is concerned with the detemination of the relationship between asphaltic concrete suface course specifications and the level of performance of pavements constructed under these specifications. The relationship was investigated through com...

Evaluation and verification of two systems for mechanistic structural design of asphalt concrete pavements in Nebraska

NASA Astrophysics Data System (ADS)

Sneddon, R. V.

1982-07-01

The VESY-3-A mechanistic design system for asphalt pavements was field verified for three pavement sections at two test sites in Nebraska. PSI predictions from VESYS were in good agreement with field measurements for a 20 year old 3 layer pavement located near Elmwood, Nebraska. Field measured PSI values for an 8 in. full depth pavement also agreed with VESYS predictions for the study period. Rut depth estimates from the model were small and were in general agreement with field measurements. Cracking estimates were poor and tended to underestimate the time required to develop observable fatigue cracking in the field. Asphalt, base course and subgrade materials were tested in a 4.0 in. diameter modified triaxial cell. Test procedures used dynamic conditioning and rest periods to simulate service conditions.

Estimation of Asphalt Pavement Life

DOT National Transportation Integrated Search

2002-01-01

The milling of asphalt concrete (AC) pavement surface refers to the mechanical removal of a part of the pavement surface. The Kansas Department of Transportation (KDOT) and the Kansas Turnpike Authority (KTA) routinely mill the surfaces of some AC pa...

An assessment of SBS modified asphalt concrete pavements performance features performing numerical analysis

NASA Astrophysics Data System (ADS)

Karakas, Ahmet Sertac; Bozkurt, Tarik Serhat; Sayin, Baris; Ortes, Faruk

2017-07-01

In passenger and freight traffic on the roads, which has the largest share of the hot mix asphalt (HMA) prepared asphalt concrete pavement is one of the most preferred type of flexible superstructure. During the service life of the road, they must provide the performance which is expected to show. HMA must be high performance mix design, comfortable, safe and resistance to degradation. In addition, it becomes a critical need to use various additives materials for roads to be able to serve long-term against environmental conditions such as traffic and climate due to the fact that the way of raw materials is limited. Styrene Butadiene Styrene (SBS) polymers are widely used among additives. In this study, the numerical analysis of SBS modified HMA designed asphalt concrete coatings prepared with different thicknesses with SBS modified HMA is performed. After that, stress and deformation values of the three pavement models are compared and evaluated.

Thermal behavior of crumb-rubber modified asphalt concrete mixtures

NASA Astrophysics Data System (ADS)

Epps, Amy Louise

Thermal cracking is one of the primary forms of distress in asphalt concrete pavements, resulting from either a single drop in temperature to an extreme low or from multiple temperature cycles above the fracture temperature of the asphalt-aggregate mixture. The first mode described is low temperature cracking; the second is thermal fatigue. The addition of crumb-rubber, manufactured from scrap tires, to the binder in asphalt concrete pavements has been suggested to minimize both types of thermal cracking. Four experiments were designed and completed to evaluate the thermal behavior of crumb-rubber modified (CRM) asphalt-aggregate mixtures. Modified and unmodified mixture response to thermal stresses was measured in four laboratory tests. The Thermal Stress Restrained Specimen Test (TSRST) and the Indirect Tensile Test (IDT) were used to compare mixture resistance to low temperature cracking. Modified mixtures showed improved performance, and cooling rate did not affect mixture resistance according to the statistical analysis. Therefore results from tests with faster rates can predict performance under slower field rates. In comparison, predicted fracture temperatures and stresses (IDT) were generally higher than measured values (TSRST). In addition, predicted fracture temperatures from binder test results demonstrated that binder testing alone is not sufficient to evaluate CRM mixtures. Thermal fatigue was explored in the third experiment using conventional load-induced fatigue tests with conditions selected to simulate daily temperature fluctuations. Test results indicated that thermal fatigue may contribute to transverse cracking in asphalt pavements. Both unmodified and modified mixtures had a finite capacity to withstand daily temperature fluctuations coupled with cold temperatures. Modified mixtures again exhibited improved performance. The fourth experiment examined fracture properties of modified and unmodified mixtures using a common fracture toughness test

Assessment of asphalt concrete acoustic performance in urban streets.

PubMed

Paje, S E; Bueno, M; Terán, F; Viñuela, U; Luong, J

2008-03-01

Geo-referenced close proximity rolling noise and sound absorption measurements are used for acoustical characterization of asphalt concrete surfaces in an urban environment. A close proximity noise map of streets with low speed limits is presented for a reference speed of 50 km/h. Different pavements and pavement conditions, common in urban streets, are analyzed: dense and semidense asphalt concrete, with Spanish denomination D-8 and S-12, respectively, and on the other hand, dense pavement at the end of its service life (D-8(*)). From the acoustics point of view, the most favorable surface, by more than 4 dB(A) compared with the S-12 mix, is the smoothest surface, i.e., the D-8 mix, even though it presents a minor absorption coefficient in normal incidence. Noise levels from dense surfaces (D-8) increase significantly over time, principally due to the appearance of surface defects such as cracks and ruts. Longitudinal variability of the close proximity tire/pavement noise emission and surface homogeneity are also analyzed.

Tolerable strains for hot mix asphalt overlays over concrete pavements : [technical summary].

DOT National Transportation Integrated Search

2013-01-01

Due to change of temperature and/or moisture, freezing-thaw cycles, loss of subgrade support by erosion, and traffic loading, concrete pavements can develop different types of distresses during service life. Hot mix asphalt (HMA) overlays are commonl...

Thermal stability analysis under embankment with asphalt pavement and cement pavement in permafrost regions.

PubMed

Junwei, Zhang; Jinping, Li; Xiaojuan, Quan

2013-01-01

The permafrost degradation is the fundamental cause generating embankment diseases and pavement diseases in permafrost region while the permafrost degradation is related with temperature. Based on the field monitoring results of ground temperature along G214 Highway in high temperature permafrost regions, both the ground temperatures in superficial layer and the annual average temperatures under the embankment were discussed, respectively, for concrete pavements and asphalt pavements. The maximum depth of temperature field under the embankment for concrete pavements and asphalt pavements was also studied by using the finite element method. The results of numerical analysis indicate that there were remarkable seasonal differences of the ground temperatures in superficial layer between asphalt pavement and concrete pavement. The maximum influencing depth of temperature field under the permafrost embankment for every pavement was under the depth of 8 m. The thawed cores under both embankments have close relation with the maximum thawed depth, the embankment height, and the service time. The effective measurements will be proposed to keep the thermal stabilities of highway embankment by the results.

Thermal Stability Analysis under Embankment with Asphalt Pavement and Cement Pavement in Permafrost Regions

PubMed Central

Jinping, Li; Xiaojuan, Quan

2013-01-01

The permafrost degradation is the fundamental cause generating embankment diseases and pavement diseases in permafrost region while the permafrost degradation is related with temperature. Based on the field monitoring results of ground temperature along G214 Highway in high temperature permafrost regions, both the ground temperatures in superficial layer and the annual average temperatures under the embankment were discussed, respectively, for concrete pavements and asphalt pavements. The maximum depth of temperature field under the embankment for concrete pavements and asphalt pavements was also studied by using the finite element method. The results of numerical analysis indicate that there were remarkable seasonal differences of the ground temperatures in superficial layer between asphalt pavement and concrete pavement. The maximum influencing depth of temperature field under the permafrost embankment for every pavement was under the depth of 8 m. The thawed cores under both embankments have close relation with the maximum thawed depth, the embankment height, and the service time. The effective measurements will be proposed to keep the thermal stabilities of highway embankment by the results. PMID:24027444

Asphalt pavement maintenance field handbook

DOT National Transportation Integrated Search

2001-04-01

This field manual provides guidelines for preventive asphalt pavement maintenance techniques for a variety of distresses and conditions. It covers: 1. crack treatments (clean and seal, rout and seal, full-depth crack repair); 2. surface treatments (f...

Enhanced treatment selection for reflective joint cracking in composite pavements : final report.

DOT National Transportation Integrated Search

2015-09-01

This research developed a decisionmaking process that can be used by INDOT to enhance identification of the condition of the : underlying concrete joints or cracks by looking at the surface distresses of the asphalt overlay in composite pavements....

Influence of hot asphalt mixture using asbuton on road composite pavement

NASA Astrophysics Data System (ADS)

Gaus, Abdul; Darwis, Muhammad; Imran

2017-11-01

Construction and rehabilitation of road infrastructure in Indonesia require about 1.2 million tons of asphalt per year, approximately 100% used of petroleum asphalt. Only a half of asphalt demand can be provided domestically, while about 600 thousand tons have to be imported from abroad. Indonesia has natural asphalt with a quite large deposit but has not been fully utilized. Lack of availability of asphalt and the increasing demand of the domestic market will give effect to an increase in bitumen cost in the domestic market. Somehow, this is not a sufficient condition due to the rising cost of road infrastructure. This study aims to determine the effect of using a layer of asphalt concrete pavement asbuton to rigid pavement (PR-modification). Stressing that occur in rigid pavement, asphalt concrete layer and base course measured by using LVDT and for the subgrade using soil pressure transducer. Using asbuton on asphalt concrete will have more benefit on improving the stability of the marshall. The maximum deflection occurring in the PR-modification at 5.19 mm with a maximum stress of 175.10 kN. Vertical and horizontal tension that occur at the base course at -20 cm row by 0.855 MPa and 0.00282 MPa. Addition of layers of asphalt concrete in rigid pavement using asbuton has increased power by 9.5%.

Investigation of aged hot-mix asphalt pavements.

DOT National Transportation Integrated Search

2013-09-01

Over the lifetime of an asphalt concrete (AC) pavement, the roadway requires periodic resurfacing and rehabilitation to provide : acceptable performance. The most popular resurfacing method is an asphalt overlay over the existing roadway. In the desi...

Effectiveness of two reflection crack attenuation techniques.

DOT National Transportation Integrated Search

2015-09-01

Asphalt overlays are one of the most common tools for rehabilitating existing asphalt and concrete pavements. : However, the performance of new overlays is often jeopardized by the cracking distress in the existing : pavement. This existing cracking ...

A simple test procedure for evaluating low temperature crack resistance of asphalt concrete : executive summary report.

DOT National Transportation Integrated Search

2009-03-01

Low temperature cracking is one of the major : distress modes in asphalt pavement and is : disastrous to pavement performance and service : life. A poor riding surface leads to an increase in : maintenance and eventual early replacement of : the pave...

Basic Performance of Fibre Reinforced Asphalt Concrete with Reclaimed Asphalt Pavement Produced In Low Temperatures with Foamed Bitumen

NASA Astrophysics Data System (ADS)

Chomicz-Kowalska, Anna; Iwański, Mateusz M.; Mrugała, Justyna

2017-10-01

During the reconstruction of road pavements, the reclaimed asphalt pavement (RAP), which is obtained through milling of the worn out existing asphalt, is commonly used for producing new base courses in cold recycling processes. Two of these techniques are most popular: one using mineral-cement-emulsion mixes and one utilizing mineral cement mixes with foamed bitumen. Additionally, some amounts of RAP can be incorporated into traditional hot mix asphalt. The demand for energy efficient and environmentally friendly solutions however, results in a need for development of new techniques that would result in cheaper and more reliable solutions with smaller carbon footprint. The reduction of processing temperatures with simultaneous incorporation of reclaimed material is the most efficient way of obtaining these objectives, but it often results in the overall decrease of bituminous mix quality. The paper presents the possibility of using RAP for producing asphalt concrete in warm mix asphalt (WMA) production process by the use of foamed bitumen modified with Fischer-Tropsch synthetic wax and polymer-basalt fibers. Additionally, a series of reference mixtures were produced to investigate the effects of the additives and of the warm process. The carried out analyses and tests shown that the experimental warm mix asphalt produced with RAP and foamed bitumen returned satisfactory performance. The introduction of synthetic F-T wax in the warm foam bitumen mixes resulted in a significantly improved compaction levels and moisture and frost resistance and the addition of polymer-basalt fibers has further improved the permanent deformation resistance of the mixes. All of the designed and tested mixes have fulfilled the requirements for binding course asphalt concrete with medium traffic loads.

Recycled Asphalt Pavement and Crushed Concrete Backfill: State-of-the-Art Review and Material Characterization

DOT National Transportation Integrated Search

2001-10-01

This report describes research results from the first year of a three-year study focused on the use of recycled asphalt pavement (RAP) and crushed concrete (CC) as backfill for mechanically stabilized earth (MSE) walls.

Asphalt-Rubber SAMI (Stress-Absorbing Membrane Interlayers) Field Evaluation.

DTIC Science & Technology

1986-04-01

revealed that there was promise in using the material as an interlayer to prevent the reflection of cracks from an old pavement to a new asphalt -concrete...reflection cracking , and (2) that asphalt - rubber interlayers should be investigated in conjunction with conventional asphalt -concrete overlays. An... Asphalt -rubber samples were taken and tested and construction activities were documented. The performance has been monitored by conducting crack

Latex improvement of recycled asphalt pavement

NASA Astrophysics Data System (ADS)

Drennon, C.

1982-08-01

The performance of a single unmodified milled recycled asphalt concrete was compared to milled asphalt concrete modified by addition of three types of rubber latex. Latex was added at 2, 3, 5, and 8 percent latex by weight of asphalt in the asphalt concrete. Lattices used were a styrene butadiene (SBR), a natural rubber (NR), an acrylonitrile butadiene (NBR), and four varieties of out of specification SBR lattices. Marshall tests, while indecisive, showed a modest improvement in properties of SBR and NR added material at 3 and 5 percent latex. Addition of NBR latex caused deterioration in Marshall stability and flow over that of control. Repeated load tests were run using the indirect tensile test, analyzed by the VESYS program, which computes life of pavements. Repeated load tests showed improvement in asphalt concrete life when 3 and 5 percent SBR was added. Improvement was also shown by the out of specification SBR.

D-cracking field performance of Portland cement concrete pavements containing limestone in Kansas : phase 1 report.

DOT National Transportation Integrated Search

2012-05-01

Premature deterioration of concrete pavement due to D-Cracking has been a problem in Kansas since the 1930s. : Limestone is the major source of coarse aggregate in eastern Kansas where the majority of the concrete pavements are : constructed. D-Crack...

Control of reflection cracking in a fabric-reinforced overlay on jointed portland cement concrete pavement.

DOT National Transportation Integrated Search

1982-01-01

A study of the installation and three-year performance evaluation of a fabric-reinforced bituminous concrete overlay of a jointed concrete pavement is reported. The fabric, a polypropylene in an asphaltic mastic, was shown to act as a significant det...

Strain transfer analysis of optical fiber based sensors embedded in an asphalt pavement structure

NASA Astrophysics Data System (ADS)

Wang, Huaping; Xiang, Ping

2016-07-01

Asphalt pavement is vulnerable to random damage, such as cracking and rutting, which can be proactively identified by distributed optical fiber sensing technology. However, due to the material nature of optical fibers, a bare fiber is apt to be damaged during the construction process of pavements. Thus, a protective layer is needed for this application. Unfortunately, part of the strain of the host material is absorbed by the protective layer when transferring the strain to the sensing fiber. To account for the strain transfer error, in this paper a theoretical analysis of the strain transfer of a three-layered general model has been carried out by introducing Goodman’s hypothesis to describe the interfacial shear stress relationship. The model considers the viscoelastic behavior of the host material and protective layer. The effects of one crack in the host material and the sensing length on strain transfer relationship are been discussed. To validate the effectiveness of the strain transfer analysis, a flexible asphalt-mastic packaged distributed optical fiber sensor was designed and tested in a laboratory environment to monitor the distributed strain and appearance of cracks in an asphalt concrete beam at two different temperatures. The experimental results indicated that the developed strain transfer formula can significantly reduce the strain transfer error, and that the asphalt-mastic packaged optical fiber sensor can successfully monitor the distributed strain and identify local cracks.

Assessment of asphalt concrete reinforcement grid in flexible pavements : final report.

DOT National Transportation Integrated Search

2016-05-01

This report investigated the application of accepted methods of pavement structural evaluation to independently assess the potential structural benefit of asphalt geogrid reinforcement of an operational flexible highway pavement. The asphalt interlay...

Reflective crack mitigation guide for flexible pavements.

DOT National Transportation Integrated Search

2015-09-01

Reflective cracks form in pavements when hot-mix asphalt (HMA) overlays are placed over jointed and/or severely cracked rigid : and flexible pavements. In the first part of the research, survival analysis was conducted to identify the most appropriat...

Implementation and Validation of the Viscoelastic Continuum Damage Theory for Asphalt Mixture and Pavement Analysis in Brazil

NASA Astrophysics Data System (ADS)

Nascimento, Luis Alberto Herrmann do

This dissertation presents the implementation and validation of the viscoelastic continuum damage (VECD) model for asphalt mixture and pavement analysis in Brazil. It proposes a simulated damage-to-fatigue cracked area transfer function for the layered viscoelastic continuum damage (LVECD) program framework and defines the model framework's fatigue cracking prediction error for asphalt pavement reliability-based design solutions in Brazil. The research is divided into three main steps: (i) implementation of the simplified viscoelastic continuum damage (S-VECD) model in Brazil (Petrobras) for asphalt mixture characterization, (ii) validation of the LVECD model approach for pavement analysis based on field performance observations, and defining a local simulated damage-to-cracked area transfer function for the Fundao Project's pavement test sections in Rio de Janeiro, RJ, and (iii) validation of the Fundao project local transfer function to be used throughout Brazil for asphalt pavement fatigue cracking predictions, based on field performance observations of the National MEPDG Project's pavement test sections, thereby validating the proposed framework's prediction capability. For the first step, the S-VECD test protocol, which uses controlled-on-specimen strain mode-of-loading, was successfully implemented at the Petrobras and used to characterize Brazilian asphalt mixtures that are composed of a wide range of asphalt binders. This research verified that the S-VECD model coupled with the GR failure criterion is accurate for fatigue life predictions of Brazilian asphalt mixtures, even when very different asphalt binders are used. Also, the applicability of the load amplitude sweep (LAS) test for the fatigue characterization of the asphalt binders was checked, and the effects of different asphalt binders on the fatigue damage properties of the asphalt mixtures was investigated. The LAS test results, modeled according to VECD theory, presented a strong correlation with

Quantify the energy and environmental effects of using recycled asphalt and recycled concrete for pavement construction phase I : final report.

DOT National Transportation Integrated Search

2009-08-01

The objective of this study is to quantify the energy and environment impacts from using recycled materials : for highway construction. Specifically, when recycled asphalt pavement is re-used for producing hot mix : asphalt or when recycled concrete ...

Epoxy asphalt concrete is a perspective material for the construction of roads

NASA Astrophysics Data System (ADS)

Vyrozhemskyi, Valerii; Kopynets, Ivan; Kischynskyi, Sergii; Bidnenko, Nataliia

2017-09-01

An effective way to increase the durability of asphalt concrete pavements that are subject to high traffic loads and adverse weather and climatic factors is the use of polymer additives which drastically improve the rheological and physical-mechanical properties of bitumen. The use of thermosetting polymers including epoxy resins for asphalt and bitumen modification is seen as a perspective solution for this issue. Conducted at DerzhdorNDI SE studies have proved high riding qualities of asphalt pavements that contain epoxy resins. When replacing 20-35% of bitumen with epoxy component, a significant improvement in strength characteristics of asphalt pavement is noted, especially at elevated temperatures. Specific feature of epoxy asphalt concrete is its ability to gain strength over a long-term operation. Thus, despite the increased cost of epoxy asphalt concrete, long service life of pavements on its basis (up to 30 years as predicted) ensures a high profitability of using this material, especially on the roads with heavy traffic and severe traffic conditions.

Investigation of aged hot-mix asphalt pavements : technical summary.

DOT National Transportation Integrated Search

2013-09-01

Over the lifetime of an asphalt concrete (AC) pavement, the roadway requires periodic resurfacing and rehabilitation to provide acceptable performance. The most popular resurfacing method is an asphalt overlay over the existing roadway. In the design...

Compaction of asphaltic concrete pavement with high intensity pneumatic roller : part II : densification due to traffic.

DOT National Transportation Integrated Search

1965-10-01

In the early of 1961 a research project was undertaken by the Louisiana Department of Highways in cooperation with the Bureau of Public Roads to study the effect of high intensity pneumatic rollers on the density of asphaltic concrete pavement using ...

The Concrete and Pavement Challenge

ERIC Educational Resources Information Center

Roman, Harry T.

2012-01-01

The modern world is characterized by the extensive use of concrete and asphalt pavement. Periodically, these materials are replaced and the old materials disposed of. In this challenge, students will be asked to develop ways to reuse the old materials. It is important for students to understand how concrete and asphalt are made and applied, as…

Investigation of reflective cracking mitigation techniques : [summary].

DOT National Transportation Integrated Search

2014-03-01

When new asphalt is placed over concrete or : asphalt pavement, cracks or joints in the old : layer can appear in the new overlay; this is : called reflective cracking (RC). In current Florida : practice, an asphalt rubber membrane interlayer : (ARMI...

Asphalt concrete overlays on CRCP : decision criteria, tack coat evaluation, and asphalt concrete mixture evaluation.

DOT National Transportation Integrated Search

2005-02-01

This report presents the research undertaken within two areas of study of thin asphalt concrete (AC) overlays to rehabilitate : continuously reinforced concrete pavements (CRCP). The first one is the development of a decision tree for the project : s...

Asphalt pavement aging and temperature dependent properties using functionally graded viscoelastic model

NASA Astrophysics Data System (ADS)

Dave, Eshan V.

Asphalt concrete pavements are inherently graded viscoelastic structures. Oxidative aging of asphalt binder and temperature cycling due to climatic conditions being the major cause of non-homogeneity. Current pavement analysis and simulation procedures dwell on the use of layered approach to account for these non-homogeneities. The conventional finite-element modeling (FEM) technique discretizes the problem domain into smaller elements, each with a unique constitutive property. However the assignment of unique material property description to an element in the FEM approach makes it an unattractive choice for simulation of problems with material non-homogeneities. Specialized elements such as "graded elements" allow for non-homogenous material property definitions within an element. This dissertation describes the development of graded viscoelastic finite element analysis method and its application for analysis of asphalt concrete pavements. Results show that the present research improves efficiency and accuracy of simulations for asphalt pavement systems. Some of the practical implications of this work include the new technique's capability for accurate analysis and design of asphalt pavements and overlay systems and for the determination of pavement performance with varying climatic conditions and amount of in-service age. Other application areas include simulation of functionally graded fiber-reinforced concrete, geotechnical materials, metal and metal composites at high temperatures, polymers, and several other naturally existing and engineered materials.

Potential applications of paving fabrics to reduce reflective cracking.

DOT National Transportation Integrated Search

2005-02-01

Asphalt concrete overlay on the existing pavement is often used as a cost-saving : surface treatment for deteriorating pavements. A major problem encountered with asphalt : resurfacing is the phenomenon termed reflective cracking, the propagation of ...

Colorado Department of Transportation hot-mix asphalt crack sealing and filling best practices guidelines.

DOT National Transportation Integrated Search

2014-10-01

Crack sealing and filling on hot mix asphalt (HMA) pavements are cost-effective pavement preservation techniques that improve pavement performance and : extend the life of existing pavements. If performed in a timely and effective manner, crack seali...

Implementation of Texas asphalt concrete overlay design system.

DOT National Transportation Integrated Search

2014-08-01

An asphalt overlay design system was developed for Texas Department of Transportation (TxDOT) under : Research Project 0-5123. The new overlay design system, named the Texas Asphalt Concrete Overlay : Design System (TxACOL), can help pavement enginee...

Asphalt Pavement Aging and Temperature Dependent Properties Using Functionally Graded Viscoelastic Model

ERIC Educational Resources Information Center

Dave, Eshan V.

2009-01-01

Asphalt concrete pavements are inherently graded viscoelastic structures. Oxidative aging of asphalt binder and temperature cycling due to climatic conditions being the major cause of non-homogeneity. Current pavement analysis and simulation procedures dwell on the use of layered approach to account for these non-homogeneities. The conventional…

Recommendations for extending asphalt pavement surface life within Washington State.

DOT National Transportation Integrated Search

2016-10-01

This study identifies and evaluates hot mix asphalt (HMA) mix design and construction techniques with potential for improving WSDOT pavement surface life. WSDOT pavement failure mechanisms are found to be predominantly cracking. Rutting may reach a f...

Use of reclaimed asphalt pavement in concrete pavement slabs.

DOT National Transportation Integrated Search

2012-10-01

This study evaluated the feasibiltiy of using RAP as aggregate replacement in concrete for use in pavement. Four different RAPs from FDOT approved RAP sources were used. Concrete mixtures with 0%, 20%, 40%, 70%, and 100% aggregate replacement by RAP ...

Continuously reinforced concrete pavement inventory

NASA Astrophysics Data System (ADS)

Halverson, A. D.; Hagen, M. G.

1982-09-01

A typical concrete pavement has expansion and contraction joints across and along the pavement surface. The joints allow the pavement to change in dimension with changes in temperature. A continuously reinforced concrete pavement (CRCP) does not have expansion or contraction joints. Random, closely spaced cracks are expected to develop naturally and allow for expansion and contraction due to temperature changes. The many random cracks eliminate expensive joint maintenance. This maintenance-free service life feature has not occurred in Minnesota. This CRCP inventory is a physical evaluation of the extent of corrosion on random sections of pavement. It is related to concurrent efforts which will evaluate CRCP rehabilitation techniques.

Effectiveness of crack sealing on pavement serviceability and life : executive summary report.

DOT National Transportation Integrated Search

2011-06-01

Sealing of cracks in asphalt surfaced pavements has long been one of the widely practiced pavement maintenance strategies by the highway agencies in including Ohio Department of Transportation. Crack sealing is performed with intent to reduce water i...

D-cracking field performance of portland cement concrete pavements containing limestone in Kansas : phase 1 report : technical summary.

DOT National Transportation Integrated Search

2012-05-01

Introduction: Premature deterioration of concrete pavement due to D-cracking has been a problem in Kansas since the 1930s. Limestone is the major source of coarse aggregate in eastern Kansas where the majority of the concrete pavements are constructe...

In-Place Recycling and Reclamation of Asphaltic Concrete Pavements in Kentucky

DOT National Transportation Integrated Search

2017-11-01

Full-depth reclamation has been defined by the Asphalt Recycling and Reclaiming Association as a rehabilitation technique in which the full thickness of the asphalt pavement and a predetermined portion of the underlying material (base, subbase, an...

Performance of warranted asphalt pavements : smoothness and performance of Indiana warranted asphalt pavements.

DOT National Transportation Integrated Search

2016-06-01

In the early 1990s the Indiana Department of Transportation (INDOT) developed a five-year warranty specification for asphalt pavements : with the first project being built in 1996. In 2004, results indicated that the asphalt pavements built with the ...

Nondestructive evaluation of the complex modulus master curve of asphalt concrete specimens

NASA Astrophysics Data System (ADS)

Gudmarsson, A.; Ryden, N.; Birgisson, B.

2013-01-01

The dynamic Young's modulus of asphalt concrete is directly related to pavement quality and is used in thickness design of pavements. There is a need for a nondestructive laboratory method to evaluate the complex modulus, which can be linked to nondestructive field measurements. This study applies seismic measurements to an asphalt concrete beam where resonant acoustic spectroscopy and optimization of frequency response functions are used to estimate the complex moduli. A good estimation of the master curve is obtained.

Asphalt concrete properties and performance in Alaska : final report

DOT National Transportation Integrated Search

1981-07-01

This report examines asphalt pavement properties of 117 older highway sections within the State of Alaska. Principal research objectives included: 1) documentation of commonly measured physical properties of the asphalt concrete cores and extracted a...

Designing fine aggregate mixtures to evaluate fatigue crack-growth in asphalt mixtures.

DOT National Transportation Integrated Search

2011-04-01

Fatigue cracking is a significant form of pavement distress in flexible pavements. The properties of the : sand-asphalt mortars or fine aggregate matrix (FAM) can be used to characterize the evolution of fatigue : crack growth and self-healing in asp...

Development and performance research of FBG strain sensor for monitoring on asphalt concrete pavement

NASA Astrophysics Data System (ADS)

Hu, Qingli; Wang, Chuan; Ou, Jinping

2010-04-01

Stiffness of asphalt concrete is very low, so ordinary FRP or steel packaged sensors are not suitable for measuring its strain accurately. In view of the problem, one innovative kind of optical fiber Bragg grating sensor packaged with polypropylene, a thermoplastic resin, was proposed in this article. Firstly, a conveniently assembled and dissembled steel die was designed and fabricated. Then, after characteristics study of polypropylene during heating and cooling repeatedly, the reliable grouting technique was formed. After this, real-time monitor of the entire sensor packaging process including die apartness was performed, and then, the sensor mechanics performance, the microscopic structure and other properties were studied thoroughly. Results of SEM indicate that interface of optical fiber and polypropylene is considerable tight. Measured strain during sensor making is reasonable. The FBG sensor was also embedded into a concrete column to measure its strain during continuously 7 day-long early-age solidification and compressive strain. Additionally, the FBG was also used to measure strain of asphalt concrete beam. Linearity and repeatability of the sensors are quit well and measured strains are quite believable. So, we can say that due to deformation compatibility between packaged material and FBG, FBG sensor and be measured material, especially low modulus of packaging materials, the strain of asphalt pavement can be monitored reliably by the sensor.

Size-dependent enrichment of waste slag aggregate fragments abraded from asphalt concrete.

PubMed

Takahashi, Fumitake; Shimaoka, Takayuki; Gardner, Kevin; Kida, Akiko

2011-10-30

Authors consider the environmental prospects of using melted waste slag as the aggregate for asphalt pavement. In particular, the enrichment of slag-derived fragments in fine abrasion dust particles originated from slag asphalt concrete and its size dependency were concerned. A series of surface abrasion tests for asphalt concrete specimens, containing only natural aggregates as reference or 30 wt% of substituted slag aggregates, were performed. Although two of three slag-asphalt concretes generated 1.5-3.0 times larger amount of abrasion dust than the reference asphalt concrete did, it could not be explained only by abrasion resistance of slag. The enrichment of slag-derived fragments in abrasion dust, estimated on the basis of the peak intensity of quartz and heavy metal concentrations, had size dependency for all slag-asphalt concretes. Slag-derived fragments were enriched in abrasion dust particles with diameters of 150-1000 μm. Enrichment factors were 1.4-2.1. In contrast, there was no enrichment in abrasion dust particles with diameter less than 75 μm. This suggests that prior airborne-size fragmentation of substituted slag aggregates does not need to be considered for tested slag aggregates when environmental risks of abrasion dust of slag-asphalt pavement are assessed. Copyright © 2011 Elsevier B.V. All rights reserved.

Evaluation of Long-Life Concrete Pavement Practices for Use in Florida

DOT National Transportation Integrated Search

2012-11-01

Current Florida construction practices produce asphalt pavements with a service life of 12 to 20 years before needing rehabilitation; concrete pavements are typically designed for 20 years. However, pavements with much longer design lives are possibl...

Mix design of asphalt mixture used for the waterproof and anti-cracking layer in the rainy area of South China.

PubMed

Liu, Fuming; Dong, Aixia; Liu, Chaoqun; Wu, Wenqing

2018-01-01

In this study, the asphalt mixture (porosity <2%) was tested for use between the upper and middle layers of the asphalt pavement to improve its interlayer structure and to enhance its related waterproof and anti-cracking ability. Considering the weather characteristics and traffic conditions in Jiangxi Province, appropriate raw materials were selected. Based on the technical indexes of the raw materials, expected porosity (<2%), and AC-5 standard for the asphalt mixture, experiments were conducted to determine the best gradation range of the waterproof and anti-cracking layer, and to obtain the optimum amount of the asphalt and fiber used based on Marshall tests. The high-temperature rutting test, low-temperature cracking test, and water stability test were conducted to evaluate the pavement performance of the waterproof and anti-cracking layer. A waterproof and anti-cracking layer was added between the upper and middle layers of the asphalt pavement, which has excellent performance for avoiding cracks and water damage.

Evaluation of asphalt pavement interface conditions for enhanced bond performance.

DOT National Transportation Integrated Search

2017-05-01

This project describes a comprehensive modeling effort aimed at examining the potential impact of interface debonding on near-surface longitudinal cracking in the wheelpath of asphalt pavements. A critical zone defined by high shear stress coupled wi...

Evaluation of precut transverse cracks for an asphalt concrete pavement in interior Alaska (Moose Creek - Richardson Highway).

DOT National Transportation Integrated Search

2015-08-01

Road-width thermal cracks (major transverse cracks) are perhaps the most noticeable form of crack-related damage on AC pavements : throughout colder areas of Alaska. The main objective of this study is to recommend design strategies and construction ...

Field manual for crack sealing in asphalt pavements.

DOT National Transportation Integrated Search

2006-01-01

This field manual was developed as a product of research project 4061 Comparison of Hot Poured Crack Sealant to Emulsified Asphalt Crack Sealant conducted by The University of Texas at Austin Center for Transportation Research (CTR). Organizati...

Evaluation of Long-Life Concrete Pavement Practices for Use in Florida : [Summary

DOT National Transportation Integrated Search

2012-01-01

Current Florida construction practices produce asphalt pavements with a service life of 12 to 20 years before needing rehabilitation; concrete pavements are typically designed for 20 years. However, pavements with much longer design lives are possibl...

Durable high strength cement concrete topping for asphalt roads

NASA Astrophysics Data System (ADS)

Vyrozhemskyi, Valerii; Krayushkina, Kateryna; Bidnenko, Nataliia

2017-09-01

Work on improving riding qualities of pavements by means of placing a thin cement layer with high roughness and strength properties on the existing asphalt pavement were conducted in Ukraine for the first time. Such pavement is called HPCM (High Performance Cementitious Material). This is a high-strength thin cement-layer pavement of 8-9 mm thickness reinforced with metal or polymer fiber of less than 5 mm length. Increased grip properties are caused by placement of stone material of 3-5 mm fraction on the concrete surface. As a result of the research, the preparation and placement technology of high-strength cement thin-layer pavement reinforced with fiber was developed to improve friction properties of existing asphalt pavements which ensures their roughness and durability. It must be emphasized that HPCM is a fundamentally new type of thin-layer pavement in which a rigid layer of 10 mm thickness is placed on a non-rigid base thereby improving riding qualities of asphalt pavement at any season of a year.

Experimental Investigation of Bio-Sealants Used for Pavement Preservation and Development of a New Strength Test for Asphalt Binders at Low Temperature

NASA Astrophysics Data System (ADS)

Ghosh, Debaroti

Surface treatment using sealants as a mean of pavement preservation is an important tool for cost-effectively extending service life of pavement. Sealants have become an important tool for cost-effectively extending the service life pavements. Due to the combined negative effects of asphalt aging and thermal cracking, it is always more challenging to choose an appropriate preservation technique for pavements built in cold-regions. Asphalt aging and thermal cracking negatively affect pavements built in cold climates. Therefore, it is important to evaluate the effects of sealants in laboratory conditions before application in the field to ensure effective performance. However, preservation activities cannot effectively address major distresses, such as low-temperature cracking, that can occur when the pavement was built from the very beginning with less durable materials. Therefore, an essential requirement to mitigate low-temperature cracking of pavements for asphalt materials used in the construction of pavement built in cold- regions is ensuring proper fracture properties of the asphalt materials used in construction. This study has two parts. In the first part, a laboratory evaluation of the effects of adding bio-sealants to both asphalt binder and mixture is performed. The goal is to obtain relevant properties of treated asphalt materials to understand the mechanism by which sealants improve pavement performance. For asphalt binders, a dynamic shear rheometer and a bending beam rheometer were used to obtain rheological properties of treated and untreated asphalt binders. For asphalt mixtures, field cores from both untreated and treated sections were collected and thin beam specimens were prepared from the cores to compare the creep and strength properties of the field-treated and laboratory-treated mixture. It is observed that the oil-based sealants have a significant softening effect on the control binder compared to the water-based sealant and traditional

A Multiscale Virtual Fabrication and Lattice Modeling Approach for the Fatigue Performance Prediction of Asphalt Concrete

NASA Astrophysics Data System (ADS)

Dehghan Banadaki, Arash

Predicting the ultimate performance of asphalt concrete under realistic loading conditions is the main key to developing better-performing materials, designing long-lasting pavements, and performing reliable lifecycle analysis for pavements. The fatigue performance of asphalt concrete depends on the mechanical properties of the constituent materials, namely asphalt binder and aggregate. This dependent link between performance and mechanical properties is extremely complex, and experimental techniques often are used to try to characterize the performance of hot mix asphalt. However, given the seemingly uncountable number of mixture designs and loading conditions, it is simply not economical to try to understand and characterize the material behavior solely by experimentation. It is well known that analytical and computational modeling methods can be combined with experimental techniques to reduce the costs associated with understanding and characterizing the mechanical behavior of the constituent materials. This study aims to develop a multiscale micromechanical lattice-based model to predict cracking in asphalt concrete using component material properties. The proposed algorithm, while capturing different phenomena for different scales, also minimizes the need for laboratory experiments. The developed methodology builds on a previously developed lattice model and the viscoelastic continuum damage model to link the component material properties to the mixture fatigue performance. The resulting lattice model is applied to predict the dynamic modulus mastercurves for different scales. A framework for capturing the so-called structuralization effects is introduced that significantly improves the accuracy of the modulus prediction. Furthermore, air voids are added to the model to help capture this important micromechanical feature that affects the fatigue performance of asphalt concrete as well as the modulus value. The effects of rate dependency are captured by

Hot in-Place Recycling of Asphalt Pavements.

DTIC Science & Technology

1987-08-04

WEARING SPECIFIED THICKNESS SURFACE • b. With ’Tew Aggregate, Modifier, And Asphalt ," ..’ . ,,, /f",’"" 4.. Figure 8. Typical Cold In-Place...34. .. .; ’-. , .?-. . ; ,....",.’.". ’. .- +-;-?,..- . .-’. , .. ’.,,..-, . ..- ?.,,,..-N ....-, ..,-. -".,,’." - HOT IN-PLACE RECYCLING OF ASPHALT PAVEMENTS An Engineering Report by0 Michael Lawrence Dowdy Submitted...for asphalt pavements. This type of asphalt pavement recycling process is becoming

Effectiveness of noise barriers installed adjacent to transverse grooved concrete pavement.

DOT National Transportation Integrated Search

2009-10-16

In recent years the Ohio Department of Transportation (ODOT) has reconstructed a number of roadways where asphalt pavements were replaced with random transverse grooved concrete pavements. Upon completion, residents living adjacent to the reconstruct...

Current Practices on Nighttime Pavement Construction Asphaltic Concrete.

DTIC Science & Technology

1982-07-01

repair: None g. Slab removals and replacements: None. h. Other ( mudjacking , asphalt underseal): None. i. Heater scarifying: None. j. Milling: None. k...g. Slab removals and replacements: None. h. Other ( mudjacking , asphalt underseal): None. i. Heater scarifying: None. j. Milling was performed...None e. "D" line cracking repair - None f. Spall repair - None g. Slab removals and replacements - None h. Other ( mudjacking , asphalt underseal) - None

Evaluation of asphalt pavement interface conditions for enhanced bond performance : [summary].

DOT National Transportation Integrated Search

2017-05-01

In this project, University of Florida researchers conducted a comprehensive program of modeling to understand interface debonding and near-surface longitudinal cracking in the wheel path of asphalt pavements. : To understand the interaction of debon...

An evaluation of dense graded asphalt-rubber concrete in Minnesota. Final report

DOT National Transportation Integrated Search

1991-11-01

The Minnesota Department of Transportation is continually investigating ways to improve the cold temperature performance of its asphalt concrete pavements. One reported method is to modify the asphalt binder with ground reclaimed automobile and truck...

Performance of TenCate Paving interlayers in asphalt concrete pavements.

DOT National Transportation Integrated Search

2017-08-01

As a continued effort of a previously completed project entitled Performance of TenCate Mirafi PGM-G4 Interlayer-Reinforced Asphalt Pavements in Alaska, this project evaluated two newly modified paving interlayers (TruPave and Mirapave) through...

Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modeling

NASA Astrophysics Data System (ADS)

Safaei, Farinaz; Castorena, Cassie; Kim, Y. Richard

2016-08-01

Fatigue cracking is a major form of distress in asphalt pavements. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design mixtures and pavements that are not susceptible to premature fatigue failure. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. In this study, the S-VECD model, developed for asphalt mixtures, is adapted for asphalt binders tested under cyclic torsion in a dynamic shear rheometer. Derivation of the model framework is presented. The model is verified by producing damage characteristic curves that are both temperature- and loading history-independent based on time sweep tests, given that the effects of plasticity and adhesion loss on the material behavior are minimal. The applicability of the S-VECD model to the accelerated loading that is inherent of the linear amplitude sweep test is demonstrated, which reveals reasonable performance predictions, but with some loss in accuracy compared to time sweep tests due to the confounding effects of nonlinearity imposed by the high strain amplitudes included in the test. The asphalt binder S-VECD model is validated through comparisons to asphalt mixture S-VECD model results derived from cyclic direct tension tests and Accelerated Loading Facility performance tests. The results demonstrate good agreement between the asphalt binder and mixture test results and pavement performance, indicating that the developed model framework is able to capture the asphalt binder's contribution to mixture fatigue and pavement fatigue cracking performance.

Asphalt in Pavement Maintenance.

ERIC Educational Resources Information Center

Asphalt Inst., College Park, MD.

Maintenance methods that can be used equally well in all regions of the country have been developed for the use of asphalt in pavement maintenance. Specific information covering methods, equipment and terminology that applies to the use of asphalt in the maintenance of all types of pavement structures, including shoulders, is provided. In many…

A multiscale model for predicting the viscoelastic properties of asphalt concrete

NASA Astrophysics Data System (ADS)

Garcia Cucalon, Lorena; Rahmani, Eisa; Little, Dallas N.; Allen, David H.

2016-08-01

It is well known that the accurate prediction of long term performance of asphalt concrete pavement requires modeling to account for viscoelasticity within the mastic. However, accounting for viscoelasticity can be costly when the material properties are measured at the scale of asphalt concrete. This is due to the fact that the material testing protocols must be performed recursively for each mixture considered for use in the final design.

Research notes : exploratory study of hot-in-place recycling of asphalt pavements.

DOT National Transportation Integrated Search

1995-06-01

In 1992, the Oregon Department of Transportation (ODOT) contracted for six hot in-place recycling (HIR) projects for rehabilitation of asphalt concrete pavements. Five projects were constructed in 1992; the sixth was constructed in 1993.

Wordburn hot in-plant asphalt pavement recycling project : final report.

DOT National Transportation Integrated Search

1992-05-01

In 1977, the Oregon Department of Transportation constructed a demonstration project using approximately 47,000 tons of stockpiled asphalt concrete (AC) material to overlay a section of pavement in Oregon. The stockpiled AC material was hot in-plant ...

Use of fiber reinforced concrete for concrete pavement slab replacement.

DOT National Transportation Integrated Search

2014-03-01

Unlike ordinary concrete pavement, replacement concrete slabs need to be open to traffic within 24 hours (sooner in : some cases). Thus, high early-strength concrete is used; however, it frequently cracks prematurely as a result of high : heat of hyd...

Design and construction guidelines for thermally insulated concrete pavements.

DOT National Transportation Integrated Search

2013-01-01

The report describes the construction and design of composite pavements as a viable design strategy to use an : asphalt concrete (AC) wearing course as the insulating material and a Portland cement concrete (PCC) structural : layer as the load-carryi...

Voids characteristics of asphaltic concrete containing coconut shell

NASA Astrophysics Data System (ADS)

Ezree Abdullah, Mohd; Hannani Madzaili, Amirah; Putra Jaya, Ramadhansyah; Yaacob, Haryati; Hassan, Norhidayah Abdul; Nazri, Fadzli Mohamed

2017-07-01

Asphalt durability is often linked to the thickness of the asphalt coating on the aggregate particles. In order to have adequate film thickness in asphaltic concrete, there must be sufficient space between the aggregate particles in the compacted pavement. This void space is referred to as voids in total mix (VTM), voids with filled bitumen (VFB), and voids in mineral aggregate (VMA). Hence, this study investigates the performance of coconut shell (CS) as coarse aggregate replacement on voids characteristics of asphaltic concrete. Four CS were used as coarse aggregates replacement in asphalt mixture namely 0%, 10%, 20%, 30%, and 40% (by weight volume). The voids properties of asphalt mixture were determined based on Marshall Mix design test. Test results show that VTM and VMA values were decrease with the increasing bitumen content where VFB was increase with increasing bitumen content. Furthermore, increasing the percentage of coconut shell in asphalt mixture was found to increases the voids value up to a peak level and then decreases with further additions of CS.

Evaluation of synthetic fabrics for the reduction of reflective cracking : final report.

DOT National Transportation Integrated Search

1975-04-01

This research was undertaken to evaluate the effectiveness of two synthetic fabrics in relieving stress and reducing or eliminating reflection cracking in the asphaltic concrete overlay of existing distressed concrete pavements. : The polypropylene f...

Effect of mineral additives on structure and properties of concrete for pavements

NASA Astrophysics Data System (ADS)

Sobol, Khrystyna; Markiv, Taras; Hunyak, Oleksii

2017-12-01

Concrete pavements is an attractive alternative to asphalt pavements because of its lower cost and higher durability. Major contribution to sustainable development can be made by partial replacement of cement in concrete pavement with supplementary cementitious materials of different nature and origin. In this paper, the effect of natural zeolite and perlite additives in complex with chemical admixtures on the structure and properties of concrete for pavement was studied. Compressive and flexural strength test was used to study the mechanical behavior of designed concrete under load. Generally, the compressive strength of both control concrete and concrete containing mineral additives levels at the later ages of hardening. The microstructure analysis of concrete with mineral additives of different nature activity showed the formation of additional amount of hydration products such as tobermorite type calcium hydrosilicate which provide self-reinforcement of hardening concrete system.

Crack and seat concrete pavement

DOT National Transportation Integrated Search

1987-09-01

Prevention of reflective cracking in HMAC overlays placed over PCCP has been based on experience gained from trial and error methods of in-service pavements in many states. Arizona recently utilized this technique on a PCCP section of Interstate 40 b...

Perform an investigation of the effects of increased reclaimed asphalt pavement (RAP) levels in dense graded friction courses.

DOT National Transportation Integrated Search

2015-04-01

In this study, a total of 28 mixture combinations were designed and evaluated to : determine the maximum allowable amount of reclaimed asphalt pavement (RAP) : material in friction courses without jeopardizing pavement cracking performance. The : exp...

Asphalt Overlay Design Methods for Rigid Pavements Considering Rutting, Reflection Cracking, and Fatigue Cracking

DOT National Transportation Integrated Search

1998-10-01

The overall objectives of this study were (1) to provide basic performance evaluation of asphalt overlays on rigid pavements and (2) to provide a design tool for supporting a long-range rehabilitation plan for the US 59 : corridor in the Lufkin Distr...

Effectiveness of noise barriers installed adjacent to transverse grooved concrete pavement : executive summary report.

DOT National Transportation Integrated Search

2009-10-16

In recent years the Ohio Department of Transportation (ODOT) has reconstructed a number of roadways where asphalt pavements were replaced with concrete pavements which were finished with a random transverse grooved surface texture (ODOT specification...

The shakeout scenario: Meeting the needs for construction aggregates, asphalt, and concrete

USGS Publications Warehouse

Langer, W.H.

2011-01-01

An Mw 7.8 earthquake as described in the ShakeOut Scenario would cause significantdamage to buildings and infrastructure. Over 6 million tons of newly mined aggregate would be used for emergency repairs and for reconstruction in the five years following the event. This aggregate would be applied mostly in the form of concrete for buildings and bridges, asphalt or concrete for pavement, and unbound gravel for applications such as base course that goes under highway pavement and backfilling for foundations and pipelines. There are over 450 aggregate, concrete, and asphalt plants in the affected area, some of which would be heavily damaged. Meeting the increased demand for construction materials would require readily available permitted reserves, functioning production facilities, a supply of cement and asphalt, a source of water, gas, and electricity, and a trained workforce. Prudent advance preparations would facilitate a timely emergency response and reconstruction following such an earthquake. ?? 2011, Earthquake Engineering Research Institute.

Research on fatigue cracking growth parameters in asphaltic mixtures using computed tomography

NASA Astrophysics Data System (ADS)

Braz, D.; Lopes, R. T.; Motta, L. M. G.

2004-01-01

Distress of asphalt concrete pavement due to repeated bending from traffic loads has been a well-recognized problem in Brazil. If it is assumed that fatigue cracking growth is governed by the conditions at the crack tip, and that the crack tip conditions can be characterized by the stress intensity factor, then fatigue cracking growth as a function of stress intensity range Δ K can be determined. Computed tomography technique is used to detect crack evolution in asphaltic mixtures which were submitted to fatigue tests. Fatigue tests under conditions of controlled stress were carried out using diametral compression equipment and repeat loading. The aim of this work is imaging several specimens at different stages of the fatigue tests. In preliminary studies it was noted that the trajectory of a crack was influenced by the existence of voids in the originally unloaded specimens. Cracks would first be observed in the central region of a specimen, propagating in the direction of the extremities. Analyzing the graphics, that represent the fatigue cracking growth (d c/d N) as a function of stress intensity factor (Δ K), it is noticed that the curve has practically shown the same behavior for all specimens at the same level of the static tension rupture stress. The experimental values obtained for the constants A and n (of the Paris-Erdogan Law) present good agreement with the results obtained by Liang and Zhou.

Characteristic Asphalt Concrete Wearing Course (ACWC) Using Variation Lime Filler

NASA Astrophysics Data System (ADS)

Permana, R. A.; Pramesti, F. P.; Setyawan, A.

2018-03-01

This research use of lime filler Sukaraja expected add durability layers of concrete pavement is asphalt damage caused by the weather and load traffic. This study attempts to know how much value characteristic Marshall on a mixture of concrete asphalt using lime filler. This research uses experimental methods that is with a pilot to get results, thus will look filler utilization lime on construction concrete asphalt variation in filler levels 2 %, 3 %, 4 %.The results showed that the use of lime filler will affect characteristic a mixture of concrete asphalt. The more filler chalk used to increase the value of stability. On the cretaceous filler 2 % value of stability is 1067,04 kg. When lime filler levels added to the levels of filler 4 %, the value of stability increased to 1213,92 kg. The flexibility increased the number of filler as levels lime 2 % to 4 % suggests that are conducted more stiff mix.

Crumb rubber modified asphalt concrete in Oregon : summary report.

DOT National Transportation Integrated Search

1995-07-01

Over the last nine years, the Oregon Department of Transportation (ODOT) has constructed 13 projects using crumb rubber modifiers (CRMs) in asphalt concrete pavements using both the wet and dry process. Three of the projects included more than one ty...

Steel slag in hot mix asphalt concrete : final report

DOT National Transportation Integrated Search

2000-04-01

In September 1994, steel slag test and control sections were constructed in Oregon to evaluate the use of steel slag in hot mix asphalt concrete (HMAC). This report covers the construction and five-year performance of a pavement constructed with 30% ...

Determination of Stone-Mastic Asphalt Concrete Durability

NASA Astrophysics Data System (ADS)

Yastremsky, D. A.; Abaidullina, T. N.; Chepur, P. V.

2018-05-01

The paper is focused on determination of durability of the stone-mastic asphalt (SMA) concrete, containing various stabilizing additives: "Armidon" (authors’ development) and "Viatop". At the first stage of experiments, the APA method was used to determine the rutting in the SMA containing these additives. Strength test for only top layers of asphalt concrete surface is insufficient for the calculation of the pavement fatigue resistance limits. Due to this fact, a comprehensive approach was employed which incorporates the interaction of the surface and subgrade natural soil. To analyze the road surface stress-strain state and to determine the durability margin, a numerical model was used (describes the processes of fatigue life). The model was developed basing on the finite element method (FEM) in the ANSYS program. Conducted studies and numerical calculations allowed obtaining the minimum and maximum stress values in the structure affected zones and in the zones of plastic deformations occurrence in artificial and natural bases. It allows predicting deformation processes during repeated wheel loads caused by moving vehicles. In course of studies, the results of static stresses in the pavement were also obtained.

Evaluation of latex polymers to resist stripping in asphalt pavements in Oregon : final report.

DOT National Transportation Integrated Search

2005-03-01

This study assessed the effectiveness of latex polymer anti-stripping treatment by inspecting and evaluating the : condition of pavements constructed in Oregon from 1997-2001. Ten hot mix asphalt concrete paving projects : were identified throughout ...

Use of fiber reinforced concrete for concrete pavement slab replacement : [summary].

DOT National Transportation Integrated Search

2014-03-01

Replacing cracked concrete in roadways requires : lanes to be closed and traff c disrupted. One way : to reduce road closure time is to reduce concrete : curing time. To accelerate curing time, pavement : engineers mix a very low water-cement ratio w...

Strength and deformation characteristics of pavements

NASA Astrophysics Data System (ADS)

Shook, J. F.; Kallas, B. F.; McCullough, B. F.; Taute, A.; Rada, G.; Witczak, M. W.; Heisey, J. S.; Stokoe, K. H.; Meyer, A. H.; Huffman, M. S.

The Colorado experimental base project was a full-scale field experment constructed with various thicknesses of two full depth hot mix sand asphalt beans, one full depth asphalt concrete base, and one thickness of a standard design with untreated base and subbase layers. Relative thicknesses of one asphalt concrete base, two hot mix sand asphalt bases, and one standard design with untreated base and subbase required to give an equal level of pavement performance were determined. Certain measured properties of the pavement and the pavement components were related to observed levels of performance by using both empirical and theoretical models for pavement behavior.

Producing Durable Continuously Reinforced Concrete Pavement using Glass-ceramic Coated Reinforcing Steel

DTIC Science & Technology

2010-02-01

reinforcement if the enamel is broken  Embedded cement grains hydrate if enamel is cracked to self-heal with the formation of calcium silicate hydrate Goal...Reinforced Concrete Pavement The 600% volume change in the iron to iron oxide formation put the concrete in tension and it cracks an spalls BUILDING...corrodes prematurely and delaminates the pavement  Moisture and chlorides can move through the natural porosity of concrete and the cracks in the

Analysis of the usage of rubberized asphalt in hot mix asphalt using Reclaimed Asphalt Pavement (RAP)

NASA Astrophysics Data System (ADS)

Dwidarma Nataadmadja, Adelia; Prahara, Eduardi; Sumbung, Pierre Christian

2017-12-01

There has been an increasing demand in using more environmentally friendly materials in pavement construction. One of the alternative materials that have been widely used is the Reclaimed Asphalt Pavement (RAP) aggregates. The RAP aggregates are derived from the crushed and screened pavement materials that contain asphalt and aggregates. This material is usually combined with natural aggregates and virgin asphalt binder to construct a new pavement. There have been numerous positive feedbacks in using this material although RAP aggregates also have certain weaknesses, such as questionable interaction between virgin and recycled materials and increased stiffness of RAP binder. Moreover, there has been a push on using rubber as an additive to asphalt binder to improve the welfare of rubber farmers. This research combines the usage of both latex and RAP as the ingredients to design hot mix asphalt (HMA) as latex could help in improving the flexibility of HMA and the interaction between the virgin and recycled materials. The main objective of this research is to find a suitable percentage of RAP aggregates to be used in HMA with certain percentage of latex as the binder additive.

Investigation of deterioration of joints in concrete pavements.

DOT National Transportation Integrated Search

2016-01-01

Premature deterioration of concrete at the joints in concrete pavements and parking lots has been reported across the northern states. The distress may first appear as shadowing when microcracking near the joints traps water, or as cracks parallel to...

Evaluation of Asphalt Pavement Analyzer for HMA Design

DOT National Transportation Integrated Search

1999-06-01

Rutting is a common problem in hot mix asphalt pavements, particularly in hot climates and at intersections. The Asphalt Pavement Analyzer (APA) is a laboratory accelerated loading equipment that can be used to evaluate rutting potential of HMA. This...

Modeling of interaction between steel and concrete in continuously reinforced concrete pavements : final report.

DOT National Transportation Integrated Search

2016-01-01

Continuously reinforced concrete pavement (CRCP) contains continuous longitudinal reinforcement with no transverse : expansion within the early life of the pavement and can continue to develop cracks in the long-term. The : accurate modeling of CRCPs...

The use of waste materials in asphalt concrete mixtures.

PubMed

Tuncan, Mustafa; Tuncan, Ahmet; Cetin, Altan

2003-04-01

The purpose of this study was to investigate (a) the effects of rubber and plastic concentrations and rubber particle sizes on properties of asphalt cement, (b) on properties of asphalt concrete specimens and (c) the effects of fly ash, marble powder, rubber powder and petroleum contaminated soil as filler materials instead of stone powder in the asphalt concrete specimens. One type of limestone aggregate and one penetration-graded asphalt cement (75-100) were used. Three concentrations of rubber and plastic (i.e. 5%, 10% and 20% of the total weight of asphalt cement), three rubber particle sizes (i.e. No. 4 [4.75mm] - 20 [0.85 mm], No. 20 [0.85mm] - 200 [0.075mm] and No. 4 [4.75mm] - 200 [0.075mm]) and one plastic particle size (i.e. No. 4 [4.75mm] - 10 [2.00mm]) were also used. It was found that while the addition of plastic significantly increased the strength of specimens, the addition of rubber decreased it. No. 4 [4.75mm] - 200 [0.075mm] rubber particles showed the best results with respect to the indirect tensile test. The Marshall stability and indirect tensile strength properties of plastic modified specimens increased. Marble powder and fly ash could be used as filler materials instead of stone powder in the asphalt concrete pavement specimens.

Pavement service life extension due to asphalt surface treatment interlayer : research project capsule.

DOT National Transportation Integrated Search

2016-07-01

The Louisiana Department of Transportation and Development (DOTD) has been : using asphalt surface treatment (AST) interlayers over soil cement base courses : as a means to mitigate shrinkage cracks from reflecting through the asphaltic : concrete (A...

Stormwater quality of spring-summer-fall effluent from three partial-infiltration permeable pavement systems and conventional asphalt pavement.

PubMed

Drake, Jennifer; Bradford, Andrea; Van Seters, Tim

2014-06-15

This study examined the spring, summer and fall water quality performance of three partial-infiltration permeable pavement (PP) systems and a conventional asphalt pavement in Ontario. The study, conducted between 2010 and 2012, compared the water quality of effluent from two Interlocking Permeable Concrete Pavements (AquaPave(®) and Eco-Optiloc(®)) and a Hydromedia(®) Pervious Concrete pavement with runoff from an Asphalt control pavement. The usage of permeable pavements can mitigate the impact of urbanization on receiving surface water systems through quantity control and stormwater treatment. The PP systems provided excellent stormwater treatment for petroleum hydrocarbons, total suspended solids, metals (copper, iron, manganese and zinc) and nutrients (total-nitrogen and total-phosphorus) by reducing event mean concentrations (EMC) as well as total pollutant loadings. The PPs significantly reduced the concentration and loading of ammonia (NH4(+)+NH3), nitrite (NO2(-)) and organic-nitrogen (Org-N) but increased the concentration and loading of nitrate (NO3(-)). The PP systems had mixed performances for the treatment of phosphate (PO4(3-)). The PP systems increased the concentration of sodium (Na) and chloride (Cl) but EMCs remained well below recommended levels for drinking water quality. Relative to the observed runoff, winter road salt was released more slowly from the PP systems resulting in elevated spring and early-summer Cl and Na concentrations in effluent. PP materials were found to introduce dissolved solids into the infiltrating stormwater. The release of these pollutants was verified by additional laboratory scale testing of the individual pavement and aggregate materials at the University of Guelph. Pollutant concentrations were greatest during the first few months after construction and declined rapidly over the course of the study. Copyright © 2014 Elsevier Ltd. All rights reserved.

Double layer drainage performance of porous asphalt pavement

NASA Astrophysics Data System (ADS)

Ji, Yangyang; Xie, Jianguang; Liu, Mingxi

2018-06-01

In order to improve the design reliability of the double layer porous asphalt pavement, the 3D seepage finite element method was used to study the drainage capacity of double layer PAC pavements with different geometric parameters. It revealed that the effect of pavement drainage length, slope, permeability coefficient and structure design on the drainage capacity. The research of this paper can provide reference for the design of double layer porous asphalt pavement in different rainfall intensity areas, and provide guides for the related engineering design.

Feasibility of reclaimed asphalt pavement as aggregate in Portland cement concrete pavements, phase II : field demonstration, [project summary].

DOT National Transportation Integrated Search

2015-10-01

Each year, the US highway : industry produces : over 100 million tons : of reclaimed asphalt : pavement (RAP) through : standard rehabilitation and : construction of the nations : roads. Although this product : has been reused in several : applica...

Longitudinal cracking in widened portland cement concrete pavements.

DOT National Transportation Integrated Search

2013-02-01

The Wisconsin Department of Transportation constructed certain concrete pavements with lane widths greater : than the standard 12 feet in order to reduce stress and deflection caused by vehicle tires running near the edge of : the concrete slabs. Man...

Determining asphalt content for recycled asphalt pavement (RAP) materials.

DOT National Transportation Integrated Search

2003-07-01

The State of Oregon uses significant amounts of Recycled Asphalt Pavement (RAP) in dense-graded mixes on State : highways. The design process for these mixes relies on accurately knowing the amount of asphalt cement in the RAP : materials being used....

Design and Properties of Asphalt Concrete Mixtures Using Renewable Bioasphalt Binder

NASA Astrophysics Data System (ADS)

Setyawan, A.; Djumari; Irfansyah, P. A.; Shidiq, A. M.; Wibisono, I. S.; Fauzy, M. N.; Hadi, F. N.

2017-02-01

The needs of petroleum asphalt as materials for pavement is very large, while the petroleum classified as natural resources that cannot be renewable. As a result of petroleum dwindling and prices tend to be more expensive. So that requiring other alternative materials as a substitute for conventional asphalt derived from biomass or often called bioasphalt. This study aims to know the volumetric and Marshall characteristics on Asphalt Cement ( AC ) using the Damar asphalt modification to substitute 60/70 penetration asphalt as a binder. The volumetric and Marshall characteristic are porosity, density, flow, stability, and Marshall quotient. The characteristic of asphalt concrete at optimum bitumen content are compared to the conditions from highway agency 1987 and the general specification of asphalt concrete Bina Marga 2010 the third revision. The research uses experimental method in the laboratory with the samples made using the dasphalt modification as binder and incorporating the aggregate gradation no. VII SNI 03-1737-1989. The research is using 15 samples divided into 5 contents of damar asphalt, they are 5%, 5,5%, 6%, 6,5%, dan 7%. Tests carried out using Marshall test equipment to get the value of flow and stability and then be searched the value of optimum damar asphalt content. The result of asphalt concrete analysis using dasphalt modification as binder gives the value of optimum dasphalt content at 5,242%. The most characteristics already met the requirements and specifications.

Rutting Performance of Cold-Applied Asphalt Repair Materials for Airfield Pavements

DTIC Science & Technology

2017-06-23

susceptibility of hot mix asphalt (HMA) using the asphalt pavement analyzer (APA). Designation T340- 10. Washington, DC: American Association of State...ER D C/ G SL T R- 17 -1 0 Rutting Performance of Cold-Applied Asphalt Repair Materials for Airfield Pavements G eo te ch ni ca l a nd S...of Cold-Applied Asphalt Repair Materials for Airfield Pavements Ben C. Cox, John F. Rushing, and Web Floyd Geotechnical and Structures Laboratory

Effectiveness of asphalt penetrating sealers in extending new asphalt pavement life.

DOT National Transportation Integrated Search

2017-01-01

Numerous methods are being employed for asphalt pavement preservation, including rejuvenator emulsions, asphalt emulsion fog seals, and a variety of non-structural surface treatments (including slurry and micro surfacing technologies). To make the mo...

Performance evaluation of high modulus asphalt concrete mixes

NASA Astrophysics Data System (ADS)

Haritonovs, V.; Tihonovs, J.; Zaumanis, M.

2016-04-01

Dolomite is one of the most available sedimentary rocks in the territory of Latvia. Dolomite quarries contain about 1000 million tons of this material. However, according to Latvian Road Specifications, this dolomite cannot be used for average and high intensity roads because of its low quality (mainly, LA index). Therefore, mostly imported magmatic rocks (granite, diabase, gabbro, basalt) or imported dolomite are used which makes asphalt expensive. However, practical experience shows that even with these high quality materials roads exhibit rutting, fatigue and thermal cracks. The aim of the research is to develop a high performance asphalt concrete for base and binder courses using only locally available aggregates. In order to achieve resistance against deformations at a high ambient temperature, a hard grade binder was used. Workability, fatigue and thermal cracking resistance, as well as sufficient water resistance is achieved by low porosity (3-5%) and higher binder content compared to traditional asphalt mixtures. The design of the asphalt includes a combination of empirical and performance based tests, which in laboratory circumstances allow simulating traffic and environmental loads. High performance AC 16 base asphalt concrete was created using local dolomite aggregate with polymer modified (PMB 10/40-65) and hard grade (B20/30) bitumen. The mixtures were specified based on fundamental properties in accordance to EN 13108-1 standard.

Mechanistic design concepts for conventional flexible pavements

NASA Astrophysics Data System (ADS)

Elliott, R. P.; Thompson, M. R.

1985-02-01

Mechanical design concepts for convetional flexible pavement (asphalt concrete (AC) surface plus granular base/subbase) for highways are proposed and validated. The procedure is based on ILLI-PAVE, a stress dependent finite element computer program, coupled with appropriate transfer functions. Two design criteria are considered: AC flexural fatigue cracking and subgrade rutting. Algorithms were developed relating pavement response parameters (stresses, strains, deflections) to AC thickness, AC moduli, granular layer thickness, and subgrade moduli. Extensive analyses of the AASHO Road Test flexible pavement data are presented supporting the validity of the proposed concepts.

High Modulus Asphalt Concrete with Dolomite Aggregates

NASA Astrophysics Data System (ADS)

Haritonovs, V.; Tihonovs, J.; Smirnovs, J.

2015-11-01

Dolomite is one of the most widely available sedimentary rocks in the territory of Latvia. Dolomite quarries contain about 1,000 million tons of this material. However, according to Latvian Road Specifications, this dolomite cannot be used for average and high intensity roads because of its low quality, mainly, its LA index (The Los Angeles abrasion test). Therefore, mostly the imported magmatic rocks (granite, diabase, gabbro, basalt) or imported dolomite are used, which makes asphalt expensive. However, practical experience shows that even with these high quality materials roads exhibit rutting, fatigue, and thermal cracks. The aim of the research is to develop a high performance asphalt concrete for base and binder courses using only locally available aggregates. In order to achieve resistance against deformations at a high ambient temperature, a hard grade binder was used. Workability, fatigue and thermal cracking resistance, as well as sufficient water resistance is achieved by low porosity (3-5%) and higher binder content compared to traditional asphalt mixtures. The design of the asphalt includes a combination of empirical and performance based tests, which in laboratory circumstances allow simulating traffic and environmental loads. High performance AC 16 base asphalt concrete was created using local dolomite aggregate with polymer modified (PMB 10/40-65) and hard grade (B20/30) bitumen. The mixtures were specified based on fundamental properties in accordance with EN 13108-1 standard.

Performance of Asphalt Concrete Wearing Course (AC-WC) Utilizing Reclaimed Asphalt Pavement from Cold Milling Bound with 80/100 Pen Asphalt

NASA Astrophysics Data System (ADS)

Thanya, I. N. A.; Suweda, I. W.; Putra, G. K.

2018-03-01

Demands on natural aggregate materials for road pavement can be reduced by utilizing reclaimed asphalt pavement (RAP). This research was aimed at evaluating the performance of AC-WC mixture using RAP materials from cold milling, bound with 80/100 pen asphalt. The RAP aggregate gradation was adjusted by adding the required amount of natural aggregates to meet the specification in Indonesia. The RAP and added aggregates were hotmixed and compacted with Marshall hummer at 2×75 blows. The asphalt content were varied. It was found that the optimum asphalt content was 6.05 % with the following Marshall characteristics: stability 1237.08 kg; flow 3.36 mm; Marshall quotient 324,73kg/mm; void in mix (VIM) 3,360%; void in mineral aggregate (VMA) 15.103; and void filled with bitumen (VFB) 77.759% and residual stability 91.04; all met the Indonesian specification. The cantabro abration loss (CAL) at 30°C was 9,02%. The indirect tensile stiffness modulus (ITSM) at 20 °C was 7961.4 MPa; dynamic creep with 100 kPa pressure at 40°C gave slope 0.0112 microsstrain/pulse which is suitable for heavy load traffic. The fatigue test results was obtained at increased stress level, i.e. at 900, 1100, and 1300 kPa. Based on the equation derived from the fatigue strain and repeated loading relationship, at 100 microstrain (με) the repeated load was 434,661.58 times, and at one million (106) repeated loading, the samples could withstand strain of 92,38 microstrain. The performance of the samples were overall better than AC-WC mixture using virgin aggregates bound with 60/70 pen asphalt.

Asphaltic concrete overlays of rigid and flexible pavements : final report.

DOT National Transportation Integrated Search

1980-10-01

This study evaluated the effect of a given thickness of asphaltic concrete overlay in rehabilitating 53 test sections conforming to the experiment design. This factorial design specified various levels of traffic intensity and overlay thickness for b...

Extending the Service Life of Pavements

NASA Astrophysics Data System (ADS)

Gschwendt, Ivan

2018-03-01

The cost of road construction and expenditures on the maintenance of pavements, i.e., their whole life cost, represents a lot of money. The paper describes a procedure for a pavement management system with degradation models and estimates the length of time for the rehabilitation of an asphalt pavement. Using a theory of pavement mechanics, we calculated the stresses and strains on the layers of two pavement models. High modulus asphalt concrete, an asphalt mix with a high binder content, and an asphalt mix with binder modifications are new road building materials. Prolonging the time for the rehabilitation of pavements is possible.

Vertical electrical impedance evaluation of asphalt overlays on concrete bridge decks

NASA Astrophysics Data System (ADS)

Baxter, Jared S.; Guthrie, W. Spencer; Waters, Tenli; Barton, Jeffrey D.; Mazzeo, Brian A.

2018-04-01

Vertical electrical impedance scanning of concrete bridge decks is a non-destructive method for quantifying the degree of protection provided to steel reinforcement against the ingress of corrosive agents. Four concrete bridge decks with asphalt overlays in northern Utah were evaluated using scanning vertical electrical impedance measurements in this study. At the time of testing, the bridges ranged in age from 21 to 34 years, and asphalt overlays had been in place for 7 to 22 years, depending on the bridge. Electrical impedance measurements were collected using a previously constructed apparatus that consisted of six probes spanning a transverse distance of 12 ft. The impedance measurements were compared to surface cracking observations and cores obtained from the same four bridge decks. The results presented in this paper demonstrate the utility of scanning vertical electrical impedance measurements for detecting cracks in asphalt overlays and quantifying their severity. In addition, the results demonstrate the sensitivity of impedance measurements to the presence of an intact membrane beneath the asphalt overlay.

Microtexture diagnostics of asphalt pavement surfaces

NASA Astrophysics Data System (ADS)

Florková, Zuzana; Pepucha, L.'ubomír

2017-09-01

The microtexture of asphalt pavement surface is an essential parameter from the traffic safety point of view and it closely relates to a geometrical, petrological and physical properties of aggregate particle used in asphalt pavement. Microtexture has a significant influence for assurance basic friction values between tire and pavement in relation to a skid resistance properties. Therefore, the microtexture detecting methods are necessary. The British pendulum tester measurements have been carried out on selected sections of roads with different asphalt surfaces. Individual grains of aggregates were taken from the surface of each section from the sliding path and also from the core sample after the extraction. The laboratory profilometry measurements have been practiced on these aggregate samples and subsequently the surface microtexture was investigated based on commonly used texture characteristics and the filtration approach was applied in calculation process. The results have shown the degradation of microtexture values occurs due to polishing of aggregate under loading from traffic in relation to the type of used aggregate. Some correlation between BPN values and texture characteristics was found.

Annual asphalt pavement industry survey on recycled materials and warm-mix asphalt usage : 2009-2012, [summary].

DOT National Transportation Integrated Search

2013-12-01

The objective of this survey was to quantify the use of recycled materials, including RAP and RAS, and WMA produced by the asphalt pavement industry. The National Asphalt Pavement Association (NAPA) conducted a voluntary survey of asphalt mixture pro...

Optical microtopographic inspection of asphalt pavement surfaces

NASA Astrophysics Data System (ADS)

Costa, Manuel F. M.; Freitas, E. F.; Torres, H.; Cerezo, V.

2017-08-01

Microtopographic and rugometric characterization of surfaces is routinely and effectively performed non-invasively by a number of different optical methods. Rough surfaces are also inspected using optical profilometers and microtopographer. The characterization of road asphalt pavement surfaces produced in different ways and compositions is fundamental for economical and safety reasons. Having complex structures, including topographically with different ranges of form error and roughness, the inspection of asphalt pavement surfaces is difficult to perform non-invasively. In this communication we will report on the optical non-contact rugometric characterization of the surface of different types of road pavements performed at the Microtopography Laboratory of the Physics Department of the University of Minho.

Characteristics and applications of high-performance fiber reinforced asphalt concrete

NASA Astrophysics Data System (ADS)

Park, Philip

Steel fiber reinforced asphalt concrete (SFRAC) is suggested in this research as a multifunctional high performance material that can potentially lead to a breakthrough in developing a sustainable transportation system. The innovative use of steel fibers in asphalt concrete is expected to improve mechanical performance and electrical conductivity of asphalt concrete that is used for paving 94% of U. S. roadways. In an effort to understand the fiber reinforcing mechanisms in SFRAC, the interaction between a single straight steel fiber and the surrounding asphalt matrix is investigated through single fiber pull-out tests and detailed numerical simulations. It is shown that pull-out failure modes can be classified into three types: matrix, interface, and mixed failure modes and that there is a critical shear stress, independent of temperature and loading rate, beyond which interfacial debonding will occur. The reinforcing effects of SFRAC with various fiber sizes and shapes are investigated through indirect tension tests at low temperature. Compared to unreinforced specimens, fiber reinforced specimens exhibit up to 62.5% increase in indirect tensile strength and 895% improvements in toughness. The documented improvements are the highest attributed to fiber reinforcement in asphalt concrete to date. The use of steel fibers and other conductive additives provides an opportunity to make asphalt pavement electrically conductive, which opens up the possibility for multifunctional applications. Various asphalt mixtures and mastics are tested and the results indicate that the electrical resistivity of asphaltic materials can be manipulated over a wide range by replacing a part of traditional fillers with a specific type of graphite powder. Another important achievement of this study is development and validation of a three dimensional nonlinear viscoelastic constitutive model that is capable of simulating both linear and nonlinear viscoelasticity of asphaltic materials. The

Characterization and Modeling of Asphalt Binder Fatigue

NASA Astrophysics Data System (ADS)

Safaei, Farinaz

Fatigue cracking is a primary distress in asphalt pavements caused by the accumulation of damage under repeated traffic loading. Many factors influence fatigue damage in pavements, including pavement structure, environmental conditions, and asphalt mixture volumetric properties. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design. A comprehensive understanding and prediction of asphalt binder fatigue performance require a suitable experiment coupled with a model to predict how the binder will perform under various traffic, temperature, and structural conditions encountered in the field. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. Although the literature shows promise for applying VECD modeling to asphalt binder fatigue, the past efforts have several shortcomings. It has been demonstrated that flow and adhesion loss can impede DSR fatigue test results. Thus, definition of test conditions (e.g., temperature) where cyclic DSR tests are appropriate for fatigue characterization of binders is necessary. In addition, the applicability of the model to predict fatigue performance under varying loading and thermal history has not been rigorously evaluated. Furthermore, the effects of material nonlinearity have been largely neglected in past modeling efforts for simplicity. In addition, past efforts have employed the parallel plate DSR geometry for the fatigue characterization of asphalt binders. In the parallel plate geometry, the strain depends on the radial distance from the specimen center. Therefore, the material will fail at different rates as a function of

Full-Depth Asphalt Pavements for Parking Lots and Driveways.

ERIC Educational Resources Information Center

Asphalt Inst., College Park, MD.

The latest information for designing full-depth asphalt pavements for parking lots and driveways is covered in relationship to the continued increase in vehicle registration. It is based on The Asphalt Institute's Thickness Design Manual, Series No. 1 (MS-1), Seventh Edition, which covers all aspects of asphalt pavement thickness design in detail,…

Analyzing the influence of manufacturing conditions of reclaimed asphalt concrete on the characteristics of the asphalt binder: development of a gradual binder extraction method

NASA Astrophysics Data System (ADS)

Navaro, J.; Bruneau, D.; Drouadaine, I.; Pouteau, B.; Colin, J.; Dony, A.

2012-05-01

When asphalt concrete is manufactured incorporating a high percentage (almost 70%) of reclaimed materials from the deconstruction of road surfaces under renovation, and when the corresponding production device is designed specifically to reduce the energy input need (lowering the production temperature), the resulting manufacturing process contributes to the protection of the environment and reduces production costs. However, to meet the quality requirements of the finished product, virgin materials of appropriate quality and quantity must also be added (mineral aggregates and new asphalt binder) and control systems set up to quantify and optimize the parameters involved (thus avoiding the guess work which still often prevails today). It was for this reason that a new experimental technique described here was devised, which will ultimately be used in asphalt concrete production plants. The technique involves lixiviating reclaimed asphalt concrete using a chlorinated solvent; the resulting solute is collected gradually, then the mixture of binders (virgin and reclaimed asphalt concrete) can be characterized and their mass fractions quantified using a combination of UV and IR spectrometry. With this experimental technique we were able to assess the extent to which the reclaimed asphalt pavement binder participates in the agglomeration and cohesion of the reclaimed asphalt concrete. This assessment was made in terms of the main parameters in the production process, temperature of the materials and mixing time.

Testing and analysis of LWT and SCB properties of asphaltic concrete mixtures : tech summary.

DOT National Transportation Integrated Search

2016-04-01

For pavement to perform well in the fi eld, a balance of both rut and crack resistance in response to the traffi c loads : and environment conditions is required. Controlling volumetric properties of a hot mix asphalt (HMA) mixture is not : enough to...

Identification of pavement distress in Kentucky.

DOT National Transportation Integrated Search

2006-04-01

In Kentucky, the roads are comprised primarily of two types of pavement. The first being Portland Cement Concrete (PCC) a rigid pavement, and the other is Asphaltic Concrete (AC), a flexible pavement. There is a noticeable difference in their appeara...

Development of quality standards for inclusion of high recycled asphalt pavement content in asphalt mixtures - phase II.

DOT National Transportation Integrated Search

2015-03-01

To conserve natural resources and energy, the amount of recycled asphalt pavement has been steadily increasing in the construction : of asphalt pavements. The objective of this study is to develop quality standards for inclusion of high RAP content. ...

Annual asphalt pavement industry survey on recycled materials and warm-mix asphalt usage : 2009-2012.

DOT National Transportation Integrated Search

2013-12-01

One of the shared goals of the Federal Highway Administration (FHWA) and the National Asphalt Pavement Association : (NAPA) is to support and promote sustainable practices such as pavement recycling and warm-mix asphalt (WMA). The use of : recycled m...

Evaluation of hot mix asphalt moisture sensitivity using the Nottingham asphalt test equipment.

DOT National Transportation Integrated Search

2005-07-01

Moisture sensitivity of Hot Mix Asphalt (HMA) mixtures, generally called stripping, is a major form of distress in asphalt concrete pavement. It is characterized by the loss of adhesive bond between the asphalt binder and the aggregate (a failure of ...

Reclaimed manufacturer asphalt roofing shingles in asphalt mixtures. Final research report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, A.B.

1999-04-23

The purpose of this project was to pave a test section using hot mix asphalt with roofing shingle pieces in the wearing and binder courses and to evaluate. The test project near Allentown, PA plus two other test projects in 1998 provide evidence of very good pavement performance. The bituminous concrete mix was modified with shredded shingles with a maximum size of 1/2 inch which added 1% of the asphalt content. The Department issued a statewide Provisional Specification titled Reclaimed Manufacturer Asphalt Roofing Shingles in Plant-Mixed Bituminous Concrete Courses'' on March 15, 1999. New manufacturer asphalt roofing shingle scrap includingmore » tab punch-outs can be successfully incorporated in bituminous concrete pavements if the shingles are shredded to 100% passing the 3/4 inch sieve. To take full advantage of the potential to replace a portion of the asphalt and therefore, reduce mix costs, shingles should be shredded to 100% passing minus 1/2 inch sieve.« less

Conclusions from the investigation of deterioration of joints in concrete pavements.

DOT National Transportation Integrated Search

2016-02-01

Premature deterioration of concrete at the joints in concrete pavements and parking lots has been reported across the northern : states. The distress may first appear as shadowing when microcracking near the joints traps water, or as cracks parallel ...

Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China.

PubMed

Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

2016-03-22

In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase.

Literature review : simple test method for possible use in predicting the fatigue of asphaltic concrete.

DOT National Transportation Integrated Search

1975-01-01

It has been recognized for many years that fatigue is one of many mechanisms by which asphaltic concrete pavements fail. Experience and empirical design procedures such as those developed by Marshall and Hveem have enabled engineers to design-mixture...

A study of sound absorption by street canyon boundaries and asphalt rubber concrete pavement

NASA Astrophysics Data System (ADS)

Drysdale, Graeme Robert

A sound field model, based on a classical diffusion equation, is extended to account for sound absorption in a diffusion parameter used to model sound energy in a narrow street canyon. The model accounts for a single sound absorption coefficient, separate accommodation coefficients and a combination of separate absorption and accommodation coefficients from parallel canyon walls. The new expressions are compared to the original formula through numerical simulations to reveal the effect of absorption on sound diffusion. The newly established analytical formulae demonstrate satisfactory agreement with their predecessor under perfect reflection. As well, the influence of the extended diffusion parameter on normalized sound pressure levels in a narrow street canyon is in agreement with experimental data. The diffusion parameters are used to model sound energy density in a street canyon as a function of the sound absorption coefficient of the street canyon walls. The acoustic and material properties of conventional and asphalt rubber concrete (ARC) pavement are also studied to assess how the crumb rubber content influences sound absorption in street canyons. The porosity and absolute permeability of compacted specimens of asphalt rubber concrete are measured and compared to their normal and random incidence sound absorption coefficients as a function of crumb rubber content in the modified binder. Nonlinear trends are found between the sound absorption coefficients, porosity and absolute permeability of the compacted specimens and the percentage of crumb rubber in the modified binders. The cross-sectional areas of the air voids on the surfaces of the compacted specimens are measured using digital image processing techniques and a linear relationship is obtained between the average void area and crumb rubber content. The measured material properties are used to construct an empirical formula relating the average porosity, normal incidence noise reduction coefficients and

Use of the asphalt pavement analyzer to study in-service asphalt mixture performance.

DOT National Transportation Integrated Search

2004-12-30

Permanent deformation or rutting is a major hot mix asphalt (HMA) performance distress. Implementation of the : Superior Performing Asphalt Pavement (Superpave) HMA mix design system was due, in part, to limit HMA rutting. : Along with the Superpave ...

Laboratory evaluation of influence of operational tolerance (acceptance criterion) on performance of hot-mix asphalt concrete.

DOT National Transportation Integrated Search

2010-06-01

The performance of flexible pavements relies heavily on the final quality of the hot-mix asphalt concrete (HMAC) as it : is produced and placed in the field. To account for production and construction variability while ensuring the quality of the : H...

Evaluation of moisture damage in asphalt concrete with CRM motorcycle tire waste passing #50 sieve size

NASA Astrophysics Data System (ADS)

Siswanto, Henri; Supriyanto, Bambang; Pranoto, Pranoto; Chandra, Pria Rizky; Hakim, Arief Rahman

2017-09-01

The objective of this experimental research is to evaluate moisture damage in Asphalt Concrete (AC) with Crumb Rubber Modified (CRM) motorcycle tire waste passing #50 and retaining #100 sieve size. Two gradations were used in this research, the first gradation is usual for asphalt concrete base (ACB) and the second gradation is for asphalt concrete wearing course (ACWC). Marshall testing apparatus was used for testing the Marshall specimens. Seven levels of CRM content were used, namely 0%, 0.5%, 1%, 1.5%, 3%, 4.5% and 6% by weight of mixtures. Retained stability represent the level of moisture damage of AC pavement. The result indicates that addition CRM to the AC mixture increases their the stability to a maximum value and subsequent addition decrease the stability. The addition CRM to AC decreases their moisture damage susceptibility. AC with 1% CRM is the best asphalt-CRM mix.

Use of the Asphalt Pavement Analyzer to study in-service asphalt mixture performance

DOT National Transportation Integrated Search

2004-12-30

Permanent deformation or rutting is a major hot mix asphalt (HMA) performance distress. Implementation of the Superior Performing Asphalt Pavement (Superpave) HMA mix design system was due, in part, to limit HMA rutting. Along with the Superpave syst...

Effect of asphalt rejuvenating agent on aged reclaimed asphalt pavement and binder properties.

DOT National Transportation Integrated Search

2016-11-01

Hot in-place recycling (HIR) preserves distressed asphalt pavements while minimizing use of virgin binder : and aggregates. The final quality of an HIR mixture depends on the characteristics of the original binder, aging of the : pavement surface dur...

Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China

PubMed Central

Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

2016-01-01

In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase. PMID:27011196

Internally cured concrete for pavement and bridge deck applications : [summary].

DOT National Transportation Integrated Search

2015-08-01

High-strength-high-performance concrete (HSHPC) is used for rapid repair of concrete : bridge decks and pavement. However, HSHPC has very high early shrinkage, often leading to : cracking, made worse by high ambient temperatures and a large surface a...

Investigation of Self Consolidating Concrete Containing High Volume of Supplementary Cementitious Materials and Recycled Asphalt Pavement Aggregates

NASA Astrophysics Data System (ADS)

Patibandla, Varun chowdary

The use of sustainable technologies such as supplementary cementitiuous materials (SCMs), and/or recycled materials is expected to positively affect the performance of concrete mixtures. However, it is important to study and qualify such mixtures and check if the required specifications of their intended application are met before they can be implemented in practice. This study presents the results of a laboratory investigation of Self Consolidating concrete (SCC) containing sustainable technologies. A total of twelve concrete mixtures were prepared with various combinations of fly ash, slag, and recycled asphalt pavement (RAP). The mixtures were divided into three groups with constant water to cementitiuous materials ratio of 0.37, and based on the RAP content; 0, 25, and 50% of coarse aggregate replaced by RAP. All mixtures were prepared to achieve a target slump flow equal to or higher than 500 mm (24in). A control mixture for each group was prepared with 100% Portland cement whereas all other mixtures were designed to have up to 70% of portland cement replaced by a combination of supplementary cementitiuous materials (SCMs) such as class C fly ash and granulated blast furnace slag. The properties of fresh concrete investigated in this study include flowability, deformability; filling capacity, and resistance to segregation. In addition, the compressive strength at 3, 14, and 28 days, the tensile strength, and the unrestrained shrinkage up to 80 days was also investigated. As expected the inclusion of the sustainable technologies affected both fresh and hardened concrete properties. Analysis of the experimental data indicated that inclusion of RAP not only reduces the ultimate strength, but it also affected the compressive strength development rate. Moreover, several mixes satisfied compressive strength requirements for pavements and bridges; those mixes included relatively high percentages of SCMs and RAP. Based on the results obtained in this study, it is not

Implementation of MEPDG for asphalt pavement with RAP.

DOT National Transportation Integrated Search

2013-06-01

This study explored the potential of using high reclaimed asphalt pavement (RAP) content with hot mix asphalt (HMA) in base and surface courses for conditions prevailing in Oklahoma. A total of eight Superpave mixes (four mixes for each of two field ...

Petrographic examination of concrete cores taken from the Ohio strategic highway research program (SHRP) specific pavement studies test road.

DOT National Transportation Integrated Search

2003-08-26

The 3-mile long SHRP pavement project is located on US 23, 25-miles north of Columbus, Ohio, : in Delaware County. Northbound lanes were constructed of portland cement concrete (PCC), : while southbound lanes were constructed of asphalt concrete (AC)...

Properties of asphalt mixtures containing RAP.

DOT National Transportation Integrated Search

2009-12-01

A typical NHDOT Hot Mix Asphalt (HMA) concrete mixture contains at least 15% Reclaimed Asphalt Pavement (RAP). The increasing cost of virgin asphalt and aggregate has increased the interest in using higher percentages of RAP in HMA mixtures. The purp...

Mechanical Properties of Portland Cement Concrete With Recycled Asphalt Pavement as Partial Replacement for Coarse Aggregate

DOT National Transportation Integrated Search

2016-06-01

Finding constructive uses for construction waste byproducts contributes to green engineering principles. One such plentiful material is recycled asphalt pavement (RAP). This report looks at the mechanical viability of including RAP in a high strength...

Microorganism Removal in Permeable Pavement Parking Lots ...

EPA Pesticide Factsheets

Three types of permeable pavements (pervious concrete, permeable interlocking concrete pavers, and porous asphalt) were monitored at the Edison Environmental Center in Edison, New Jersey for indicator organisms such as fecal coliform, enterococci, and E. coli. Results showed that porous asphalt had much lower concentration in monitored infiltrate compared to pervious concrete and permeable interlocking concrete pavers. Concentrations of monitored organisms in infiltrate from porous asphalt were consistently below the bathing water quality standard. Fecal coliform and enterococci exceeded bathing water quality standards more than 72% and 34% of the time for permeable interlocking concrete pavers and pervious concrete, respectively. Purpose is to evaluate the performance of permeable pavement in removing indicator organisms from infiltrating stormwater runoff.

Use of High-Volume Reclaimed Asphalt Pavement (RAP) for Asphalt Pavement Rehabilitation Due to Increased Highway Truck Traffic from Freight Transportation

DOT National Transportation Integrated Search

2012-06-01

A recent rise in asphalt binder prices has led state agencies and contractors to use higher quantities of Reclaimed : Asphalt Pavement (RAP). Besides being economic, sustainable, and environmentally friendly, RAP can be replaced : for a portion of ag...

Evaluation of using higher percentages of recycled asphalt pavement in asphalt mixes in Virginia.

DOT National Transportation Integrated Search

2008-01-01

In 2007, the Virginia Department of Transportation (VDOT) decided to allow higher percentages of recycled asphalt pavement (RAP), i.e., more than 20 percent, in hot-mix asphalt with no change in binder grade. Because of this increase, one section of ...

Generation of urban road dust from anti-skid and asphalt concrete aggregates.

PubMed

Tervahattu, Heikki; Kupiainen, Kaarle J; Räisänen, Mika; Mäkelä, Timo; Hillamo, Risto

2006-04-30

Road dust forms an important component of airborne particulate matter in urban areas. In many winter cities the use of anti-skid aggregates and studded tires enhance the generation of mineral particles. The abrasion particles dominate the PM10 during springtime when the material deposited in snow is resuspended. This paper summarizes the results from three test series performed in a test facility to assess the factors that affect the generation of abrasion components of road dust. Concentrations, mass size distribution and composition of the particles were studied. Over 90% of the particles were aluminosilicates from either anti-skid or asphalt concrete aggregates. Mineral particles were observed mainly in the PM10 fraction, the fine fraction being 12% and submicron size being 6% of PM10 mass. The PM10 concentrations increased as a function of the amount of anti-skid aggregate dispersed. The use of anti-skid aggregate increased substantially the amount of PM10 originated from the asphalt concrete. It was concluded that anti-skid aggregate grains contribute to pavement wear. The particle size distribution of the anti-skid aggregates had great impact on PM10 emissions which were additionally enhanced by studded tires, modal composition, and texture of anti-skid aggregates. The results emphasize the interaction of tires, anti-skid aggregate, and asphalt concrete pavement in the production of dust emissions. They all must be taken into account when measures to reduce road dust are considered. The winter maintenance and springtime cleaning must be performed properly with methods which are efficient in reducing PM10 dust.

Crack-resistant concrete : maximizing the service life of transportation infrastructure.

DOT National Transportation Integrated Search

2009-01-01

Although much progress has been made in reducing concretes propensity to crack, the goal remains elusive. A novel approach to this problem is the focus of High-Performance Stress-Relaxing Cementitious Composites for Crack-Free Pavements and Tra...

Fatigue performance of asphalt pavements containing RAS and RAP.

DOT National Transportation Integrated Search

2015-01-01

Rising oil and gas prices spurs development of methods and technologies for reducing fuel consumption and increased use of : recycled materials. With increased environmental awareness, using reclaimed asphalt pavement (RAP) and reclaimed asphalt : sh...

Asphaltic concrete overlays of rigid and flexible pavements : interim report No. 1.

DOT National Transportation Integrated Search

1977-09-01

This study evaluated the effect of a given thickness of asphaltic concrete overlay in rehabilitating 53 test sections conforming to the experiment design. This factorial design specified various levels of traffic intensity and overlay thickness for b...

Onsite use of recycled asphalt pavement materials and geocells to reconstruct pavements damaged by heavy trucks.

DOT National Transportation Integrated Search

2011-07-01

Asphalt pavements deteriorate with traffic (especially heavy trucks) and time. Maintenance and overlaying may solve minor to : medium pavement distress problems. When the condition of a pavement becomes badly deteriorated, reconstruction of the : pav...

Use of recycled chunk rubber asphalt concrete (CRAC) on low volume roads and use of recycled crumb rubber modifier in asphalt pavements. Final report, June 1993-June 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hossain, M.; Funk, L.P.; Sadeq, M.A.

1995-06-01

The major objective of this project was to formulate a Chunk Rubber Asphalt Concrete (CRAC) mix for use on low volume roads. CRAC is a rubber modified asphalt concrete product produced by the `dry process` where rubber chunks of 1/2 inch size are used as aggregate in a cold mix with a type C fly ash. The second objective of this project was to develop guidelines concerning the use of rubber modified asphalt concrete hot mix to include: (1) Design methods for use of asphalt-rubber mix for new construction and overlay, (2) Mix design method for asphalt-rubber, and (3) Testmore » method for determining the amount of rubber in an asphalt-rubber concrete for quality control purposes.« less

Performance trends of rehabilitated AC pavements

DOT National Transportation Integrated Search

2000-10-01

The General Pavement Study (GPS) 6 experiment, "AC Overlay of AC Pavements," involves pavement test sections where an asphalt concrete (AC) overlay was placed on an existing AC pavement. This TechBrief summarizes the results of a study of the GPS-6 e...

Evaluation of concrete bridge mix designs for control of cracking, phase I.

DOT National Transportation Integrated Search

2014-11-01

Cracking of concrete is a common problem with concrete structures such as bridge decks, pavements and bridge : rail. The Agency of Transportation (VTrans) has recently invested in higher performing concrete mixes that are : more impervious and has hi...

Fatigue cracking in road pavement

NASA Astrophysics Data System (ADS)

Mackiewicz, P.

2018-05-01

The article presents the problem of modelling fatigue phenomena occurring in the road pavement. The example of two selected pavements shows the changes occurring under the influence of the load in different places of the pavement layers. Attention is paid to various values of longitudinal and transverse strains generated at the moment of passing the wheel on the pavement. It was found that the key element in the crack propagation analysis is the method of transferring the load to the pavement by the tire and the strain distribution in the pavement. During the passage of the wheel in the lower layers of the pavement, a complex stress state arises. Then vertical, horizontal and tangent stresses with various values appear. The numerical analyses carried out with the use of finite element methods allowed to assess the strain and stress changes occurring in the process of cracking road pavement. It has been shown that low-thickness pavements are susceptible to fatigue cracks arising "bottom to top", while pavements thicker are susceptible to "top to bottom" cracks. The analysis of the type of stress allowed to determine the cracking mechanism.

A Study Of In-Place Rutting Of Asphalt Pavements

DOT National Transportation Integrated Search

1989-01-01

The objective of this study was to evaluate in-place pavements experiencing rutting and pavements experiencing no rutting to begin to classify asphalt mixtures that should perform satisfactorily and those that would likely rut under traffic. The info...

Evaluation of performance of asphalt pavements constructed using intelligent compaction techniques.

DOT National Transportation Integrated Search

2014-10-01

The long-term performance of asphalt pavements depends on the quality of the subgrade and : asphalt layers. Intelligent compaction methods continuously monitor the modulus/stiffness of : subgrade and asphalt layers during compaction process and have ...

The study of stiffness modulus values for AC-WC pavement

NASA Astrophysics Data System (ADS)

Lubis, AS; Muis, Z. A.; Iskandar, T. D.

2018-02-01

One of the parameters of the asphalt mixture in order for the strength and durability to be achieved as required is the stress-and-strain showing the stiffness of a material. Stiffness modulus is a very necessary factor that will affect the performance of asphalt pavements. If the stiffness modulus value decreases there will be a cause of aging asphalt pavement crack easily when receiving a heavy load. The high stiffness modulus asphalt concrete causes more stiff and resistant to bending. The stiffness modulus value of an asphalt mixture material can be obtained from the theoretical (indirect methods) and laboratory test results (direct methods). For the indirect methods used Brown & Brunton method, and Shell Bitumen method; while for the direct methods used the UMATTA tool. This study aims to determine stiffness modulus values for AC-WC pavement. The tests were conducted in laboratory that used 3 methods, i.e. Brown & Brunton Method, Shell Bitumen Method and Marshall Test as a substitute tool for the UMATTA tool. Hotmix asphalt made from type AC-WC with pen 60/70 using a mixture of optimum bitumen content was 5.84% with a standard temperature variation was 60°C and several variations of temperature that were 30, 40, 50, 70 and 80°C. The stiffness modulus value results obtained from Brown & Brunton Method, Shell Bitumen Method and Marshall Test which were 1374,93 Mpa, 235,45 Mpa dan 254,96 Mpa. The stiffness modulus value decreases with increasing temperature of the concrete asphalt. The stiffness modulus value from the Bitumen Shell method and the Marshall Test has a relatively similar value.The stiffness modulus value from the Brown & Brunton method is greater than the Bitumen Shell method and the Marshall Test, but can not measure the stiffness modulus value at temperature above 80°C.

Subsurface condition evaluation for asphalt pavement preservation treatments.

DOT National Transportation Integrated Search

2013-04-01

This report presents a case study on the SR70 section with microsurface for understanding its performance; a development of a : methodology for evaluating the asphalt pavement subsurface condition for applying pavement preservation treatments; and...

Utilizing Lab Tests to Predict Asphalt Concrete Overlay Performance

DOT National Transportation Integrated Search

2017-12-01

A series of five experimental projects and three demonstration projects were constructed to better understand the performance of pavement overlays using various levels of asphalt binder replacement (ABR) from reclaimed asphalt pavement (RAP), recycle...

Three-dimensional modeling of flexible pavements : research implementation plan.

DOT National Transportation Integrated Search

2006-02-14

Many of the asphalt pavement analysis programs are based on linear elastic models. A linear viscoelastic models : would be superior to linear elastic models for analyzing the response of asphalt concrete pavements to loads. There : is a need to devel...

Design and evaluation of foamed asphalt base materials.

DOT National Transportation Integrated Search

2013-05-01

Foamed asphalt stabilized base (FASB) combines reclaimed asphalt pavement (RAP), recycled : concrete (RC), and/or graded aggregate base (GAB) with a foamed asphalt binder to produce a : partially stabilized base material. The objectives of this study...

Operating the Portable Seismic Pavement Analyzer

DTIC Science & Technology

2006-12-01

8 Thickness versus modulus...amplitude versus time waveforms....................................................................... 9 Figure 10. A thickness versus Young’s modulus plot...modulus of portland cement concrete (PCC) and asphalt concrete (AC) pavements. Additional strength parameters necessary for structural pavement

Long-term Metal Performance of Three Permeable Pavements ...

EPA Pesticide Factsheets

EPA constructed a 4,000-m2 parking lot surfaced with three permeable pavements (permeable interlocking concrete pavers, pervious concrete, and porous asphalt) on the Edison Environmental Center in Edison, NJ in 2009. Samples from each permeable pavement infiltrate were collected for six years beginning in January 2010 and analyzed for twenty-two metals. Although the infiltrate metals concentrations varied by surface, metal concentrations in more than 99% of the permeable pavement infiltrate samples met both the groundwater effluent limitations and maximum contaminant levels in national primary drinking water regulations for barium, chromium, copper, manganese, nickel and zinc. Arsenic, cadmium, lead and antimony met those standards in 60% to 98% of the samples with no measurable difference found among pavements. Aluminum and iron in pervious concrete and porous asphalt infiltrates met standards at more than 90%, however permeable interlocking concrete paver infiltrates have 50% and 93% samples exceeds standards, respectively. Concentrations of arsenic, iron, potassium, lithium, magnesium, antimony, tin, manganese, and zinc in all permeable pavement infiltrates decreased with time, whereas, aluminum, barium, calcium, chromium and strontium in porous asphalt infiltrates increased. Most metal concentrations in permeable pavement infiltrates either exhibited no significant difference between snow/no-snow seasons or showed statistically larger concentrations

Detection of recycled asphalt pavement (RAP) in bituminous mixtures

DOT National Transportation Integrated Search

2004-06-01

The overall goal of this study was to assist the Illinois Department of Transportation (IDOT) in identifying and developing methods for quality assurance of hot-mix asphalt (HMA) containing recycled asphalt pavement (RAP). Although the use of RAP can...

Evaluation of lignin as an antioxidant in asphalt binders and bituminous mixtures.

DOT National Transportation Integrated Search

2017-01-01

The chemical process of oxidative age-hardening in asphalt pavements is one of the major distresses : leading to hot mix asphalt (HMA) pavement failure as evidenced by fatigue and thermal (low temperature) : cracking. : Research investigations at the...

Modeling the performance properties of RAS and RAP blended asphalt mixes using chemical compositional information.

DOT National Transportation Integrated Search

2017-01-01

Reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS) can improve the sustainability of asphalt concrete (AC) due to cost savings and environmental factors, but it is necessary to ensure that pavement performance is not compromised. To...

The wearing characteristics of mineral aggregates in highway pavements.

DOT National Transportation Integrated Search

1970-01-01

Fifteen asphaltic concrete and seventeen portland cement concrete pavements located in Virginia were chosen for studies of aggregate wear and related wet pavement friction. Coarse aggregates from thirteen different geologic formations and quarry sour...

Installation report : evaluation of asphalt additives.

DOT National Transportation Integrated Search

1987-01-01

Five asphalt additives that are supposed to improve the stability and flexibility characteristics of asphalt concrete were installed in pavement test sections on Route 58 in Halifax County. Polymers, latex rubbers, and a diatomaceous deposit were use...

Polymeric thermochromic dye for improvement of asphalt pavement durability : final report.

DOT National Transportation Integrated Search

2017-01-01

Asphalt pavements features good performance and relatively low construction and maintenance : costs. However, the black color of asphalt binder implies that the sunlight is not reflected but : absorbed, which raises the temperature of the asphalt pav...

Flexible pavement overlay design procedures. Volume 2: User manual

NASA Astrophysics Data System (ADS)

Majidzadeh, K.; Ilves, G. J.

1981-08-01

This user manual outlines a procedure for the design of asphaltic concrete overlays on existing asphaltic concrete pavement surfaces. It is intended as a guide to the user on the type and form of information required as input to the procedure and contains all elements necessary for the user to prepare designs for flexible pavement overlays.

Effect of asphalt rejuvenating agent on aged reclaimed asphalt pavement and binder properties : technical summary.

DOT National Transportation Integrated Search

2016-11-01

Hot in-place recycling (HIR) preserves distressed asphalt pavements while minimizing use of virgin binder and aggregates. The final quality of an HIR mixture depends on the characteristics of the original binder, aging of the pavement surface during ...

Evaluation of lignin as an antioxidant in asphalt binders and bituminous mixtures : technical summary.

DOT National Transportation Integrated Search

2017-01-01

The chemical process of oxidative age-hardening in asphalt pavements is one of the major distresses leading to hot mix asphalt (HMA) pavement failure as evidenced by fatigue and thermal (low temperature) cracking.

Long-term infiltration capacity of different types of permeable pavements.

DOT National Transportation Integrated Search

2017-08-01

Permeable pavements such as porous asphalt, pervious concrete and permeable interlocking concrete pavers are relatively novel alternatives to conventional pavement that allow rain and snowmelt to infiltrate, thereby reducing runoff, flooding and nonp...

Conclusions from the investigation of deterioration of joints in concrete pavements : intrans project reports.

DOT National Transportation Integrated Search

2016-02-01

Premature deterioration of concrete at the joints in concrete pavements and parking lots has been reported across the northern : states. The distress may first appear as shadowing when microcracking near the joints traps water, or as cracks parallel ...

Analysis on mechanics response of long-life asphalt pavement at moist hot heavy loading area

NASA Astrophysics Data System (ADS)

Xu, Xinquan; Li, Hao; Wu, Chuanhai; Li, Shanqiang

2018-04-01

Based on the durability of semi-rigid base asphalt pavement test road in Guangdong Yunluo expressway, by comparing the mechanics response of modified semi-rigid base, RCC base and inverted semi-rigid base with the state of continuous, using four unit five parameter model to evaluate rut depth of asphalt pavement structure, and through commonly used fatigue life prediction model to evaluate fatigue performance of three types of asphalt pavement structure. Theoretical calculation and four years tracking observation results of test road show that rut depth of modified semi-rigid base asphalt pavement is the minimum, the road performance is the best, and the fatigue performance is the optimal.

Long-term Metal Performance of Three Permeable Pavements

EPA Science Inventory

EPA constructed a 4,000-m2 parking lot surfaced with three permeable pavements (permeable interlocking concrete pavers, pervious concrete, and porous asphalt) on the Edison Environmental Center in Edison, NJ in 2009. Samples from each permeable pavement infiltrate were collected...

Road Asphalt Pavements Analyzed by Airborne Thermal Remote Sensing: Preliminary Results of the Venice Highway.

PubMed

Pascucci, Simone; Bassani, Cristiana; Palombo, Angelo; Poscolieri, Maurizio; Cavalli, Rosa

2008-02-22

This paper describes a fast procedure for evaluating asphalt pavement surface defects using airborne emissivity data. To develop this procedure, we used airborne multispectral emissivity data covering an urban test area close to Venice (Italy).For this study, we first identify and select the roads' asphalt pavements on Multispectral Infrared Visible Imaging Spectrometer (MIVIS) imagery using a segmentation procedure. Next, since in asphalt pavements the surface defects are strictly related to the decrease of oily components that cause an increase of the abundance of surfacing limestone, the diagnostic absorption emissivity peak at 11.2μm of the limestone was used for retrieving from MIVIS emissivity data the areas exhibiting defects on asphalt pavements surface.The results showed that MIVIS emissivity allows establishing a threshold that points out those asphalt road sites on which a check for a maintenance intervention is required. Therefore, this technique can supply local government authorities an efficient, rapid and repeatable road mapping procedure providing the location of the asphalt pavements to be checked.

Road Asphalt Pavements Analyzed by Airborne Thermal Remote Sensing: Preliminary Results of the Venice Highway

PubMed Central

Pascucci, Simone; Bassani, Cristiana; Palombo, Angelo; Poscolieri, Maurizio; Cavalli, Rosa

2008-01-01

This paper describes a fast procedure for evaluating asphalt pavement surface defects using airborne emissivity data. To develop this procedure, we used airborne multispectral emissivity data covering an urban test area close to Venice (Italy).For this study, we first identify and select the roads' asphalt pavements on Multispectral Infrared Visible Imaging Spectrometer (MIVIS) imagery using a segmentation procedure. Next, since in asphalt pavements the surface defects are strictly related to the decrease of oily components that cause an increase of the abundance of surfacing limestone, the diagnostic absorption emissivity peak at 11.2μm of the limestone was used for retrieving from MIVIS emissivity data the areas exhibiting defects on asphalt pavements surface.The results showed that MIVIS emissivity allows establishing a threshold that points out those asphalt road sites on which a check for a maintenance intervention is required. Therefore, this technique can supply local government authorities an efficient, rapid and repeatable road mapping procedure providing the location of the asphalt pavements to be checked. PMID:27879765

Evaluation of narrow transverse contraction joints in jointed plain concrete pavements.

DOT National Transportation Integrated Search

2006-03-01

This report presents the results of a research project conducted at the Louisiana Transportation Research Center (LTRC) to evaluate the performance of narrow transverse contraction joints to control cracking in jointed plain concrete pavements. In ad...

Development of a multiaxial viscoelastoplastic continuum damage model for asphalt mixtures.

DOT National Transportation Integrated Search

2009-09-01

This report highlights findings from the FHWA DTFH61-05-H-00019 project, which focused on the development of the multiaxial viscoelastoplastic continuum damage model for asphalt concrete in both compression and tension. Asphalt concrete pavement, one...

Experimental investigation of basic oxygen furnace slag used as aggregate in asphalt mixture.

PubMed

Xue, Yongjie; Wu, Shaopeng; Hou, Haobo; Zha, Jin

2006-11-16

Chinese researchers have commenced a great deal of researches on the development of application fields of basic oxygen steel making furnace slag (BOF slag) for many years. Lots of new applications and properties have been found, but few of them in asphalt mixture of road construction engineering. This paper discussed the feasibility of BOF steel slag used as aggregate in asphalt pavement by two points of view including BOF steel slag's physical and micro-properties as well as steel slag asphalt materials and pavement performances. For the former part, this paper mainly concerned the mechanochemistry and physical changes of the steel slag and studied it by performing XRD, SEM, TG and mercury porosimeter analysis and testing method. In the second part, this paper intended to use BOF steel slag as raw material, and design steel slag SMA mixture. By using traditional rutting test, soak wheel track and modified Lottman test, the high temperature stability and water resistance ability were tested. Single axes compression test and indirect tensile test were performed to evaluate the low temperature crack resistance performance and fatigue characteristic. Simultaneously, by observing steel slag SMA pavement which was paved successfully. A follow-up study to evaluate the performance of the experimental pavement confirmed that the experimental pavement was comparable with conventional asphalt pavement, even superior to the later in some aspects. All of above test results and analysis had only one main purpose that this paper validated the opinion that using BOF slag in asphalt concrete is feasible. So this paper suggested that treated and tested steel slag should be used in a more extensive range, especially in asphalt mixture paving projects in such an abundant steel slag resource region.

Comparative Evaluation of Pavement Crack Detection Using Kernel-Based Techniques in Asphalt Road Surfaces

NASA Astrophysics Data System (ADS)

Miraliakbari, A.; Sok, S.; Ouma, Y. O.; Hahn, M.

2016-06-01

With the increasing demand for the digital survey and acquisition of road pavement conditions, there is also the parallel growing need for the development of automated techniques for the analysis and evaluation of the actual road conditions. This is due in part to the resulting large volumes of road pavement data captured through digital surveys, and also to the requirements for rapid data processing and evaluations. In this study, the Canon 5D Mark II RGB camera with a resolution of 21 megapixels is used for the road pavement condition mapping. Even though many imaging and mapping sensors are available, the development of automated pavement distress detection, recognition and extraction systems for pavement condition is still a challenge. In order to detect and extract pavement cracks, a comparative evaluation of kernel-based segmentation methods comprising line filtering (LF), local binary pattern (LBP) and high-pass filtering (HPF) is carried out. While the LF and LBP methods are based on the principle of rotation-invariance for pattern matching, the HPF applies the same principle for filtering, but with a rotational invariant matrix. With respect to the processing speeds, HPF is fastest due to the fact that it is based on a single kernel, as compared to LF and LBP which are based on several kernels. Experiments with 20 sample images which contain linear, block and alligator cracks are carried out. On an average a completeness of distress extraction with values of 81.2%, 76.2% and 81.1% have been found for LF, HPF and LBP respectively.

Pavement noise measurements in Poland

NASA Astrophysics Data System (ADS)

Zofka, Ewa; Zofka, Adam; Mechowski, Tomasz

2017-09-01

The objective of this study is to investigate the feasibility of the On-Board Sound Intensity (OBSI) system to measure tire-pavement noise in Poland. In general, sources of noise emitted by the modern vehicles are the propulsion noise, aerodynamic resistance and noise generated at the tire-pavement interface. In order to capture tire-pavement noise, the OBSI system uses a noise intensity probe installed in the close proximity of that interface. In this study, OBSI measurements were performed at different types of pavement surfaces such as stone mastic asphalt (SMA), regular asphalt concrete (HMA) as well as Portland cement concrete (PCC). The influence of several necessary OBSI measurement conditions were recognized as: testing speed, air temperature, tire pressure and tire type. The results of this study demonstrate that the OBSI system is a viable and robust tool that can be used for the quality evaluation of newly built asphalt pavements in Poland. It can be also applied to generate reliable input parameters for the noise propagation models that are used to assess the environmental impact of new and existing highway corridors.

Three-Dimensional Nonlinear Finite Element Analysis of Continuously Reinforced Concrete Pavements

DOT National Transportation Integrated Search

2000-02-01

Continuously reinforced concrete pavement (CRCP)performance depends primarily on early-age cracks that result from changes in temperature and drying shrinkage. This report presents the findings of a study of the early-age behavior of CRCP in response...

Research on construction technology for orthotropic steel deck pavement of Haihe River Chunyi Bridge

NASA Astrophysics Data System (ADS)

Xue, Y. C.; Qian, Z. D.; Zhang, M.

2017-01-01

In order to ensure the good service quality of orthotropic steel deck pavement of Haihe River Chunyi Bridge in Tianjin, and to reduce the occurrence of pavement diseases like lateral and longitudinal cracks, the key working procedures such as steel deck cleaning, anticorrosive coating, bonding layer spraying, seam cutting, epoxy asphalt concrete’s mixing, transportation, paving and compaction were studied. The study was based on the main features of epoxy asphalt concrete which is the pavement materials of Haihe River Chunyi Bridge, and combined with the basic characteristics and construction conditions of Haihe River Chunyi Bridge. Furthermore, some processing measures like controlling time and temperature, continuous paving with two pavers, lateral feeding, and improving the compaction method were proposed. The project example shows that the processing measures can effectively solve the technical difficulties in the construction of orthotropic steel deck pavement of Haihe River Chunyi Bridge, can greatly improve the construction speed and quality, and can provide reference for the same kinds of orthotropic steel deck pavement construction.

Design and evaluation of foamed asphalt base materials : [research summary].

DOT National Transportation Integrated Search

2013-05-01

Foamed asphalt stabilized base (FASB) combines reclaimed asphalt pavement (RAP), : recycled concrete (RC), and/or graded aggregate base (GAB) with a foamed asphalt : binder to produce a partially stabilized base material. Although widely used, most :...

A review on using crumb rubber in reinforcement of asphalt pavement.

PubMed

Mashaan, Nuha Salim; Ali, Asim Hassan; Karim, Mohamed Rehan; Abdelaziz, Mahrez

2014-01-01

An immense problem affecting environmental pollution is the increase of waste tyre vehicles. In an attempt to decrease the magnitude of this issue, crumb rubber modifier (CRM) obtained from waste tyre rubber has gained interest in asphalt reinforcement. The use of crumb rubber in the reinforcement of asphalt is considered as a smart solution for sustainable development by reusing waste materials, and it is believed that crumb rubber modifier (CRM) could be an alternative polymer material in improving hot mix asphalt performance properties. In this paper, a critical review on the use of crumb rubber in reinforcement of asphalt pavement will be presented and discussed. It will also include a review on the effects of CRM on the stiffness, rutting, and fatigue resistance of road pavement construction.

Improved performance of reclaimed asphalt pavement mixes.

DOT National Transportation Integrated Search

2014-08-07

Utilization of RAP in asphalt pavements has become an important strategy to help offset rising : raw material prices and to improve the sustainability of our transportation infrastructure. The : South Dakota DOT began to routinely use RAP in mainl...

Extending the life of asphalt pavements (OR09-086A) : part I final report.

DOT National Transportation Integrated Search

2011-01-01

The goal of this project was to identify common features of good and poorly performing asphalt pavements. The types of asphalt pavements included in the study were grouped into four categories: new construction, crush & shape with HMA surface, mill &...

Field performance of a porous asphaltic pavement.

DOT National Transportation Integrated Search

1992-01-01

The Virginia Department of Transportation constructed a 2.52-acre parking lot of porous asphaltic pavement in Warrenton, Virginia. Runoff from the lot was collected and monitored for quantity, detention time, and quality. Prior to the lot opening for...

Monitoring and modeling of pavement response and performance task B : New York, executive summary report.

DOT National Transportation Integrated Search

2012-01-01

Problem: Perpetual asphalt concrete (AC) and long-lasting : Portland cement concrete (PCC) pavements are relatively : new to the pavement community. These newer pavements : require the use of innovative Mechanistic-Empirical (ME) : design procedures,...

Geosynthetics for reflective crack control

DOT National Transportation Integrated Search

1999-03-01

Reflective cracking due to shrinkage and brittleness in asphalt pavements can seriously degrade an asphalt overlay before it is near its design life. Geosynthetics have been used to impede the reflection of existing transverse cracking to the new ove...

Performance Testing of Hot-Mix Asphalt Aggregates

DOT National Transportation Integrated Search

1999-12-01

Hot mix asphalt (HMA) pavements are subject to thermal cracking, fatigue cracking, rutting, stripping, raveling, and freeze-thaw damage. Some of these distresses are directly affected by the choice of aggregates. Particle shape, surface texture, part...

Improving the properties of reclaimed asphalt pavement for roadway base applications [summary].

DOT National Transportation Integrated Search

2012-01-01

Over 90 percent of : U.S. roads are paved : with asphalt, which : must be periodically : resurfaced. Milling : produces reclaimed : asphalt pavement (RAP), : which can be recycled : in hot-mix asphalt, : but at no more than : 25%. Therefore, much : R...

Advanced self-healing asphalt composites in the pavement performance field: mechanisms at the nano level and new repairing methodologies.

PubMed

Agzenai, Yahya; Pozuelo, Javier; Sanz, Javier; Perez, Ignacio; Baselga, Juan

2015-01-01

In an effort to give a global view of this field of research, in this mini-review we highlight the most recent publications and patents focusing on modified asphalt pavements that contain certain reinforcing nanoparticles which impart desirable thermal, electrical and mechanical properties. In response to the increasing cost of asphalt binder and road maintenance, there is a need to look for alternative technologies and new asphalt composites, able to self-repair, for preserving and renewing the existing pavements. First, we will focus on the self-healing property of asphalt, the evidences that support that healing takes place immediately after the contact between the faces of a crack, and how the amount of healing can be measured in both the laboratory and the field. Next we review the hypothetical mechanisms of healing to understand the material behaviour and establish models to quantify the damage-healing process. Thereafter, we outline different technologies, nanotechnologies and methodologies used for self-healing paying particular attention to embedded micro-capsules, new nano-materials like carbon nanotubes and nano-fibres, ionomers, and microwave and induction heating processes.

Multiscale Constitutive Modeling of Asphalt Concrete

NASA Astrophysics Data System (ADS)

Underwood, Benjamin Shane

Multiscale modeling of asphalt concrete has become a popular technique for gaining improved insight into the physical mechanisms that affect the material's behavior and ultimately its performance. This type of modeling considers asphalt concrete, not as a homogeneous mass, but rather as an assemblage of materials at different characteristic length scales. For proper modeling these characteristic scales should be functionally definable and should have known properties. Thus far, research in this area has not focused significant attention on functionally defining what the characteristic scales within asphalt concrete should be. Instead, many have made assumptions on the characteristic scales and even the characteristic behaviors of these scales with little to no support. This research addresses these shortcomings by directly evaluating the microstructure of the material and uses these results to create materials of different characteristic length scales as they exist within the asphalt concrete mixture. The objectives of this work are to; 1) develop mechanistic models for the linear viscoelastic (LVE) and damage behaviors in asphalt concrete at different length scales and 2) develop a mechanistic, mechanistic/empirical, or phenomenological formulation to link the different length scales into a model capable of predicting the effects of microstructural changes on the linear viscoelastic behaviors of asphalt concrete mixture, e.g., a microstructure association model for asphalt concrete mixture. Through the microstructural study it is found that asphalt concrete mixture can be considered as a build-up of three different phases; asphalt mastic, fine aggregate matrix (FAM), and finally the coarse aggregate particles. The asphalt mastic is found to exist as a homogenous material throughout the mixture and FAM, and the filler content within this material is consistent with the volumetric averaged concentration, which can be calculated from the job mix formula. It is also

A Review on Using Crumb Rubber in Reinforcement of Asphalt Pavement

PubMed Central

Mashaan, Nuha Salim; Ali, Asim Hassan; Karim, Mohamed Rehan; Abdelaziz, Mahrez

2014-01-01

An immense problem affecting environmental pollution is the increase of waste tyre vehicles. In an attempt to decrease the magnitude of this issue, crumb rubber modifier (CRM) obtained from waste tyre rubber has gained interest in asphalt reinforcement. The use of crumb rubber in the reinforcement of asphalt is considered as a smart solution for sustainable development by reusing waste materials, and it is believed that crumb rubber modifier (CRM) could be an alternative polymer material in improving hot mix asphalt performance properties. In this paper, a critical review on the use of crumb rubber in reinforcement of asphalt pavement will be presented and discussed. It will also include a review on the effects of CRM on the stiffness, rutting, and fatigue resistance of road pavement construction. PMID:24688369

Crackscope : automatic pavement cracking inspection system.

DOT National Transportation Integrated Search

2008-08-01

The CrackScope system is an automated pavement crack rating system consisting of a : digital line scan camera, laser-line illuminator, and proprietary crack detection and classification : software. CrackScope is able to perform real-time pavement ins...

Effects of asphalt cement rejuvenating agents : final report.

DOT National Transportation Integrated Search

1980-08-01

Louisiana's initial work in the recycling of asphaltic concrete pavements has demonstrated the need to obtain a base of knowledge in the area of rejuvenating age-hardened reclaimed asphalt cement. In this report, eight rejuvenating agents are examine...

Concrete pavement joint deterioration.

DOT National Transportation Integrated Search

2015-12-01

Concrete pavements are an important part of our national infrastructure. In recent years the relatively small number of reported joints deteriorating prematurely in concrete pavements around Indiana has increased. Changes over the past 45 years in IN...

Geosynthetic materials in reflective crack prevention.

DOT National Transportation Integrated Search

2007-07-01

Reflective cracking due to shrinkage and brittleness in asphalt pavements can seriously degrade an asphalt overlay : before it is near the end of its design life. Geosynthetics have been used to impede the reflection of existing : transverse cracking...

Comparison Of Rehabilitation Strategies For AC Pavements

DOT National Transportation Integrated Search

2000-11-01

This TechBrief summarizes the results of a study of the Specific Pavement Study 5 (SPS-5) experiment entitled, "Performance of Rehabilitated Asphalt Concrete Pavements in the LTPP Experiments--Data Collected Through February 1997." The study document...

Performance of reclaimed asphalt pavement on unpaved roads.

DOT National Transportation Integrated Search

2011-10-01

The University of Wyoming's LTAP Center conducted a study examining the performance of reclaimed, recycled asphalt pavement (RAP) on unpaved roads in three Wyoming counties. Fifteen material and dust suppression treatment combinations were examined. ...

Developing the elastic modulus measurement of asphalt concrete using the compressive strength test

NASA Astrophysics Data System (ADS)

Setiawan, Arief; Suparma, Latif Budi; Mulyono, Agus Taufik

2017-11-01

Elastic modulus is a fundamental property of an asphalt mixture. An analytical method of the elastic modulus is needed to determine the thickness of flexible pavement. It has a role as one of the input values on a stress-strain analysis in the finite element method. The aim of this study was to develop the measurement of the elastic modulus by using compressive strength testing. This research used a set of specimen mold tool and Delta Dimensi software to record strain changes occurring in the proving ring of compression machine and the specimens. The elastic modulus of the five types of aggregate gradation and 2 types of asphalt were measured at optimum asphalt content. Asphalt Cement 60/70 and Elastomer Modified Asphalt (EMA) were used as a binder. Manufacturing success indicators of the specimens used void-in-the-mix (VIM) 3-5 % criteria. The success rate of the specimen manufacturing was more than 76%. Thus, the procedure and the compressive strength test equipment could be used for the measurement of the elastic modulus. The aggregate gradation and asphalt types significantly affected the elastic modulus of the asphalt concrete.

Evaluation of reclaimed asphalt pavement for surface mixtures.

DOT National Transportation Integrated Search

2012-03-01

The Indiana Department of Transportation has successfully used Reclaimed Asphalt Pavement (RAP) for decades because of its economic : and environmental benefits. Because of uncertainties regarding the types of aggregates contained in RAP and their re...

Evaluation of crack-sealing milled pavement in the effort to reduce transverse cracking.

DOT National Transportation Integrated Search

2015-01-01

To determine if crack sealing milled pavement prior to overlay will deter the : migration of transverse cracking, or have an effect on pavement performance, : when compared to an adjacent milled pavement that receives no crack sealing : treatment.

Evaluation of recycled concrete as aggregate in new concrete pavements.

DOT National Transportation Integrated Search

2014-04-01

This study evaluated the use of recycled concrete as coarse aggregate in new concrete pavements. : Recycled concrete aggregate (RCA) produced from demolished pavements in three geographically dispersed locations in Washington state were used to perfo...

Determination of mechanical properties of materials used in WAY-30 test pavements.

DOT National Transportation Integrated Search

2010-05-01

The US Route 30 bypass of Wooster, Ohio, in Wayne County, WAY-30, was constructed to demonstrate two types of : extended service pavements, a long-life Portland cement concrete (PCC) pavement on the eastbound lanes and an asphalt : concrete (AC...

Field Control and Performance of Asphalt Mixtures Containing Greater than 25 Percent Reclaimed Asphalt Pavement : Draft Final Report

DOT National Transportation Integrated Search

2018-02-02

The Alabama Department of Transportation (ALDOT) and other highway agencies are interested in utilization of higher percentages of reclaimed asphalt pavement (RAP) in asphalt mixtures. There are a number of research studies at both state and national...

Simulation, imaging, and mechanics of asphalt pavement (SIMAP) initiative

DOT National Transportation Integrated Search

1998-07-01

Asphalt concrete is a complex material that consists of aggregates, asphalt, and air voids. Aggregates are held together by asphalt and form a skeleton to support the weight of vehicles. The stiffer the asphalt, the tighter the aggregates are held to...

A report on Virginia specifications for penetration asphalt cements.

DOT National Transportation Integrated Search

1970-01-01

Asphaltic pavements in Virginia had shown cracks in the surface layers only, and this had led to the belief that the durability properties of the asphalt had not been what they should have been and that the asphalt specifications needed to be revised...

Mapping asphalt pavement aging and condition using multiple endmember spectral mixture analysis in Beijing, China

NASA Astrophysics Data System (ADS)

Pan, Yifan; Zhang, Xianfeng; Tian, Jie; Jin, Xu; Luo, Lun; Yang, Ke

2017-01-01

Asphalt road reflectance spectra change as pavement ages. This provides the possibility for remote sensing to be used to monitor a change in asphalt pavement conditions. However, the relatively narrow geometry of roads and the relatively coarse spatial resolution of remotely sensed imagery result in mixtures between pavement and adjacent landcovers (e.g., vegetation, buildings, and soil), increasing uncertainties in spectral analysis. To overcome this problem, multiple endmember spectral mixture analysis (MESMA) was used to map the asphalt pavement condition using Worldview-2 satellite imagery in this study. Based on extensive field investigation and in situ measurements, aged asphalt pavements were categorized into four stages-preliminarily aged, moderately aged, heavily aged, and distressed. The spectral characteristics in the first three stages were further analyzed, and a MESMA unmixing analysis was conducted to map these three kinds of pavement conditions from the Worldview-2 image. The results showed that the road pavement conditions could be detected well and mapped with an overall accuracy of 81.71% and Kappa coefficient of 0.77. Finally, a quantitative assessment of the pavement conditions for each road segment in this study area was conducted to inform road maintenance management.

Investigation of the Asphalt Pavement Analyzer (APA) testing program in Nebraska.

DOT National Transportation Integrated Search

2008-03-01

The asphalt pavement analyzer (APA) has been widely used to evaluate hot-mix asphalt (HMA) rutting potential in mix : design and quality control-quality assurance (QC-QA) applications, because the APA testing and its data analyses are : relatively si...

Thermal behavior of an asphalt pavement in the laboratory and in the parking lot.

PubMed

Martinkauppi, J B; Mäkiranta, A; Kiijärvi, J; Hiltunen, E

2015-01-01

The urban, constructed areas are full of buildings and different kinds of pavements and have a noticeable lack of trees and flora. These areas are accumulating the heat from the Sun, people, vehicles, and constructions. One interesting heat collector is the asphalt pavement. How does the heat transfer to different layers under the pavement or does it? What are the temperatures under the pavement in Finland where the winter can be pretty hard? How can those temperatures be measured accurately? These are the main questions this paper gives the preliminary answers to. First the thermal behavior of asphalt and the layers beneath are researched in the laboratory and then the measurement field is bored and dug in the parking in the Western coast of Finland, 63°5'45'' N. Distributed temperature sensing method was found to be a good choice for temperature measurements. Thermal behavior of pavement has been monitored in different layers and the preliminary results have been published here. The goal of this research is to assess the applicability of asphalt pavements for heat energy collection.

Testing protocols to ensure performance of high asphalt binder replacement mixes using RAP and RAS.

DOT National Transportation Integrated Search

2015-12-01

The use of reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS) in asphalt concrete (AC) mixtures can reduce demand for virgin aggregates and asphalt binder, bringing environmental and economic benefits. However, replacing virgin asph...

Geosynthetics for reflective crack control : construction report.

DOT National Transportation Integrated Search

1999-03-01

Reflective cracking due to shrinkage and brittleness in asphalt pavements can seriously degrade an asphalt overlay before it is near its design life. Geosynthetics have been used to impede the reflection of existing transverse cracking to the new ove...

Prediction of Low-Temperature Cracking Using Superpave Binder Specifications

DOT National Transportation Integrated Search

1996-02-01

Six different AC-20 asphalt cements were used in a Pennsylvania project in September 1976. Two of the six test pavements developed low-temperature cracking in January 1977. The remaining four test pavements started to develop cracks to different degr...

Unbonded portland cement concrete overlay/pavement monitoring with integrated grating and scattering optical fiber sensors.

DOT National Transportation Integrated Search

2014-06-01

This report summarizes the findings and results from a laboratory and field study on the strain distribution : and crack development in 3 thick concrete panels cast on top of existing concrete pavements as a rapid : rehabilitation strategy for roa...

Investigation of proposed AASHTO rut test procedure using the Asphalt Pavement Analyzer.

DOT National Transportation Integrated Search

2006-01-01

The Virginia Department of Transportation uses the Asphalt Pavement Analyzer with beam specimens to test and approve asphalt mixtures for rut resistance. Some agencies use cylindrical specimens that impart distinct testing advantages such as the ease...

Evaluation of tack coating practices for asphalt overlays in Nebraska.

DOT National Transportation Integrated Search

2017-04-03

The strength of the bond between asphalt layers affects the lifespan of pavement structures. It is also a key factor in preventing major pavement distresses, such as slippage cracking and delamination. This research project evaluates and compares the...

Asphalt pavement performance-based specifications : research brief.

DOT National Transportation Integrated Search

2017-03-01

The fundamental objective of asphalt mix design is to select an aggregate skeleton and asphalt binder content that balances constructability and performance. High performance mixtures that protect against rutting, cracking and moisture damage are dif...

Thermal Behavior of an Asphalt Pavement in the Laboratory and in the Parking Lot

PubMed Central

Martinkauppi, J. B.; Mäkiranta, A.; Kiijärvi, J.; Hiltunen, E.

2015-01-01

The urban, constructed areas are full of buildings and different kinds of pavements and have a noticeable lack of trees and flora. These areas are accumulating the heat from the Sun, people, vehicles, and constructions. One interesting heat collector is the asphalt pavement. How does the heat transfer to different layers under the pavement or does it? What are the temperatures under the pavement in Finland where the winter can be pretty hard? How can those temperatures be measured accurately? These are the main questions this paper gives the preliminary answers to. First the thermal behavior of asphalt and the layers beneath are researched in the laboratory and then the measurement field is bored and dug in the parking in the Western coast of Finland, 63°5′45′′ N. Distributed temperature sensing method was found to be a good choice for temperature measurements. Thermal behavior of pavement has been monitored in different layers and the preliminary results have been published here. The goal of this research is to assess the applicability of asphalt pavements for heat energy collection. PMID:25861679

Application of Roller Compacted Concrete in Colorado's Roadways

DOT National Transportation Integrated Search

2012-10-01

Roller Compacted Concrete (RCC) is a no-slump concrete mixture that is transported, placed, and compacted with : the same construction equipment as asphalt pavement. RCCs were used to construct three sections of pavement in : Weld County Road 28 (WCR...

Impacts of pavement types on in-vehicle noise and human health.

PubMed

Li, Qing; Qiao, Fengxiang; Yu, Lei

2016-01-01

Noise is a major source of pollution that can affect the human physiology and living environment. According to the World Health Organization (WHO), an exposure for longer than 24 hours to noise levels above 70 dB(A) may damage human hearing sensitivity, induce adverse health effects, and cause anxiety to residents nearby roadways. Pavement type with different roughness is one of the associated sources that may contribute to in-vehicle noise. Most previous studies have focused on the impact of pavement type on the surrounding acoustic environment of roadways, and given little attention to in-vehicle noise levels. This paper explores the impacts of different pavement types on in-vehicle noise levels and the associated adverse health effects. An old concrete pavement and a pavement with a thin asphalt overlay were chosen as the test beds. The in-vehicle noise caused by the asphalt and concrete pavements were measured, as well as the drivers' corresponding heart rates and reported riding comfort. Results show that the overall in-vehicle sound levels are higher than 70 dB(A) even at midnight. The newly overlaid asphalt pavement reduced in-vehicle noise at a driving speed of 96.5 km/hr by approximately 6 dB(A). Further, on the concrete pavement with higher roughness, driver heart rates were significantly higher than on the asphalt pavement. Drivers reported feeling more comfortable when driving on asphalt than on concrete pavement. Further tests on more drivers with different demographic characteristics, along highways with complicated configurations, and an examination of more factors contributing to in-vehicle noise are recommended, in addition to measuring additional physical symptoms of both drivers and passengers. While there have been many previous noise-related studies, few have addressed in-vehicle noise. Most studies have focused on the noise that residents have complained about, such as neighborhood traffic noise. As yet, there have been no complaints by

Recycled asphalt pavement - fly ash geopolymer as a sustainable stabilized pavement material

NASA Astrophysics Data System (ADS)

Horpibulsuk, S.; Hoy, M.; Witchayaphong, P.; Rachan, R.; Arulrajah, A.

2017-11-01

Strength, durability, microstructure and leachate characteristics of Recycled Asphalt Pavement and Fly Ash (RAP-FA) geopolymers and RAP-FA blends as a sustainable pavement material are evaluated in this paper. The strength development of the stabilized materials with and without effect wetting-drying (w-d) cycles was determined by Unconfined Compression Strength (UCS) test. The mineralogical and microstructural changes of the stabilized material were analyzed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The leachability of the heavy metals were measured by Toxicity Characteristic Leaching Procedure (TCLP) and compared with international standard. The results show that both RAP-FA blend and RAP-FA geopolymer increase with increasing the number of w-d cycles (C), reaching its peak at 6 w-d cycles. The XRD and SEM analyses indicate that the strength development of RAP-FA blend occurs due to stimulation of the chemical reaction between the high amount to Calcium in RAP and the high amount of Silica and Alumina in FA leaching to production of Calcium Aluminium (Silicate) Hydrate, while the geopolymerization reaction is observed in RAP-FA geopolymer. For C> 6, the significant macro- and micro-cracks developed during w-d cycles cause strength reduction for both RAP-FA blend and geopolymer. The TCLP results demonstrate that there is no environmental risk for these stabilized materials. Furthermore, FA-geopolymer can reduce the leachability of heavy metal in RAP-FA blend. The outcome from this research confirms the viability of using RAP-FA blend and RAP-FA geopolymer as alternative sustainable pavement materials.

Ground Penetrating Radar : Pavement Layer Thickness Evaluation

DOT National Transportation Integrated Search

2003-12-01

The following report demonstrates the accuracy of using Ground Penetrating Radar (GPR) to determine both the surface layer thickness for asphalt, and concrete pavements. In addition tests were conducted to identify GPR's repeatability on dry pavement...

Ground penetrating radar, pavement layer thickness evaluation

DOT National Transportation Integrated Search

2002-12-01

The following report demonstrates the accuracy of using Ground Penetrating Radar (GPR) to determine both the surface layer thickness for asphalt, and concrete pavements. In addition tests were conducted to identify GPR's repeatability on dry pavement...

Ground Penetrating Radar : Pavement Layer Thickness Evaluation

DOT National Transportation Integrated Search

2002-12-01

The following report demonstrates the accuracy of using Ground Penetrating Radar (GPR) to determine both the surface layer thickness for asphalt, and concrete pavements. In addition tests were conducted to identify GPR's repeatability on dry pavement...

Effect of Reclaimed Asphalt Pavement on Binder Properties Using the Superpave System

DOT National Transportation Integrated Search

1998-09-01

While the use of reclaimed asphalt pavement (RAP) in asphalt mixes is common practice within many state departments of transportation, the evolution of the Superpave system has prompted a need for specific Superpave guidelines for the use of RAP. In ...

40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to...

40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to...

40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to...

40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to discharges...

Modified pavement cement concrete

NASA Astrophysics Data System (ADS)

Botsman, L. N.; Ageeva, M. S.; Botsman, A. N.; Shapovalov, S. M.

2018-03-01

The paper suggests design principles of pavement cement concrete, which covers optimization of compositions and structures at the stage of mixture components selection due to the use of plasticizing agents and air-retaining substances that increase the viability of a concrete mixture. It also demonstrates advisability of using plasticizing agents together with air-retaining substances when developing pavement concrete compositions, which provides for the improvement of physical and mechanical properties of concrete and the reduction of cement binding agent consumption thus preserving strength indicators. The paper shows dependences of the main physical-mechanical parameters of concrete on cement consumption, a type and amount of additives.

Long-Term Pavement Performance Ohio SPS-1 and SPS-2 Dynamic Load Response Data Processing

DOT National Transportation Integrated Search

2015-03-01

The dynamic load response (DLR) Study Team reinterpreted 4,290 Ohio Specific Pavement Studies (SPS)-1 (asphalt concrete pavements) raw traces and 9,240 Ohio SPS-2 (portland cement concrete pavements) raw traces, correcting the data issues identified ...

Performance Assessment of Warm Mix Asphalt (WMA) Pavements

DOT National Transportation Integrated Search

2009-09-01

Abstract : Warm Mix Asphalt (WMA) is a new technology that was introduced in Europe in 1995. WMA offers several advantages over : conventional asphalt concrete mixtures, including: reduced energy consumption, reduced emissions, improved or more unifo...

Performance assessment of warm mix asphalt (WMA) pavements.

DOT National Transportation Integrated Search

2009-09-01

Warm Mix Asphalt (WMA) is a new technology that was introduced in Europe in 1995. WMA offers several advantages over : conventional asphalt concrete mixtures, including: reduced energy consumption, reduced emissions, improved or more uniform : binder...

Assessment of the Uretek process on continuously reinforced concrete pavement, jointed concrete pavement, and bridge approach slabs : technical assistance report.

DOT National Transportation Integrated Search

2004-12-01

This study evaluates the rehabilitation method utilizing the injection of Uretek (polyurethane) into the pavement structures on continuously reinforced concrete pavement (CRCP), jointed concrete pavement (JCP), and bridge approach slabs. The polyuret...

Evaluation of field projects using crumb rubber modified asphaltic concrete.

DOT National Transportation Integrated Search

2007-03-01

In 1994, the Louisiana Department of Transportation and Development (LADOTD) initiated a research project to evaluate different crumb-rubber modified (CRM) applications in which the long-term pavement performance of the CRM asphalt pavements was comp...

Implementation of warm-mix asphalt mixtures in Nebraska pavements.

DOT National Transportation Integrated Search

2012-07-01

The primary objective of this research is to evaluate the feasibility of several WMA mixtures as potential asphalt paving : mixtures for Nebraska pavements. To that end, three well-known WMA additives (i.e., Sasobit, Evotherm, and Advera : synthetic ...

Evaluation of recycled asphaltic concrete : final report.

DOT National Transportation Integrated Search

1977-01-01

This report describes a project in which approximately 6,200 tons (5,630 Mg) of asphaltic concrete were recycled through a conventional asphalt batch plant. During the construction of the project, a buildup of asphalt-coated fines occurred in the dry...

Application of high performance concrete in the pavement system : structural response of high performance concrete pavements.

DOT National Transportation Integrated Search

2002-03-01

Rigid pavements make up a significant percentage of highway systems in the United States and abroad. Concrete pavements provide an economical and durable solution for highway systems, because the pavements last longer and require less maintenance. Re...

Mechanistic-empirical asphalt overlay thickness design and analysis system.

DOT National Transportation Integrated Search

2009-10-01

The placement of an asphalt overlay is the most common method used by the Texas Department of Transportation (TxDOT) to rehabilitate : existing asphalt and concrete pavements. The type of overlay and its required thickness are important decisions tha...

Exploratory study of hot-in-place recycling of asphalt pavements, volume II : appendices.

DOT National Transportation Integrated Search

1994-11-01

Hot-in-place recycling (HIR) is a method for rehabilitation of asphalt pavements. Potential for cost savings and resource preservation are high because existing pavement materials are processed on-site, with only the addition of small amounts of recy...

Performance of Hot Mix Asphalt Mixture Incorporating Kenaf Fibre

NASA Astrophysics Data System (ADS)

Hainin, M. R.; Idham, M. K.; Yaro, N. S. A.; Hussein, S. O. A. E.; Warid, M. N. M.; Mohamed, A.; Naqibah, S. N.; Ramadhansyah, P. J.

2018-04-01

Kenaf fibre has been recognised to increase the strength of concrete, but its application in asphalt concrete is still unanswered. This research investigated the performance of Hot Mix Asphalt (HMA) incorporated with different percentages of kenaf fibre (0.1 %, 0.2% and 0.3% by weight of dry aggregate) in term of resilient modulus, rutting performance using Asphalt Pavement analyser (APA) and moisture damage using the Modified Lottman test (AASHTO-T283). The fibre was interweaved to a diameter of about 5-10 mm and length of 30 mm which is three times the nominal maximum aggregate size used in the mix. Asphaltic mixtures of asphalt concrete (AC) 10 were prepared and compacted using Marshall compactor which were subsequently tested to evaluate the resilient modulus and moisture susceptibility. Twelve cylindrical specimens (150mm diameter) from AC10, two control samples with two modified ones for each percentage of kenaf fibres compacted using Gyratory compactor were used for rutting test using APA. The laboratory results reveal that the addition of kenaf fibres slightly reduce the resilient modulus of the mixes and that asphaltic mix with 0.3% kenaf fibre can mitigate both rutting and moisture damage which makes the pavement more sustain to the loads applied even in the presence of water. 0.3% kenaf fibre content is considered to be the optimal content which had the least rut depth and the highest TSR of 81.07%. Based on grid analysis, addition of 0.3% kenaf fibre in asphaltic concrete was recommended in modifying the samples.

Full-Scale Accelerated Pavement Testing of Warm-Mix Asphalt (WMA) for Airfield Pavements

DTIC Science & Technology

2014-01-01

software and Pavement Engineering Utility (PSEVEN) were used 50 ft 65 ft 130 ft 24 ft Item 3 Sasobit ® Item 4 Evotherm 3G Item 1 HMA... Evotherm 3G Air Top Mid-depth Bottom Target temperature = 109 ºF ERDC/GSL TR-14-3 25 The target pavement temperature for this study was 109 ºF, and it is...the locations of the I-buttons and their layout in relation to the vents. 90 95 100 105 110 115 120 HMA Foamed Asphalt Sasobit Evotherm 3G Av er ag e

Development of asphalt dynamic modulus master curve using falling weight deflectometer measurements.

DOT National Transportation Integrated Search

2014-06-01

The asphalt concrete (AC) dynamic modulus (|E*|) is a key design parameter in mechanistic-based pavement design : methodologies such as the American Association of State Highway and Transportation Officials (AASHTO) MEPDG/Pavement-ME Design. The obje...

Performance testing of asphalt concrete containing crumb rubber modifier and warm mix additives

NASA Astrophysics Data System (ADS)

Ikpugha, Omo John

Utilisation of scrap tire has been achieved through the production of crumb rubber modified binders and rubberised asphalt concrete. Terminal and field blended asphalt rubbers have been developed through the wet process to incorporate crumb rubber into the asphalt binder. Warm mix asphalt technologies have been developed to curb the problem associated with the processing and production of such crumb rubber modified binders. Also the lowered production and compaction temperatures associated with warm mix additives suggests the possibility of moisture retention in the mix, which can lead to moisture damage. Conventional moisture sensitivity tests have not effectively discriminated good and poor mixes, due to the difficulty of simulating field moisture damage mechanisms. This study was carried out to investigate performance properties of crumb rubber modified asphalt concrete, using commercial warm mix asphalt technology. Commonly utilised asphalt mixtures in North America such as dense graded and stone mastic asphalt were used in this study. Uniaxial Cyclic Compression Testing (UCCT) was used to measure permanent deformation at high temperatures. Indirect Tensile Testing (IDT) was used to investigate low temperature performance. Moisture Induced Sensitivity Testing (MiST) was proposed to be an effective method for detecting the susceptibility of asphalt mixtures to moisture damage, as it incorporates major field stripping mechanisms. Sonnewarm(TM), Sasobit(TM) and Evotherm(TM) additives improved the resistance to permanent deformation of dense graded mixes at a loading rate of 0.5 percent by weight of the binder. Polymer modified mixtures showed superior resistance to permanent deformation compared to asphalt rubber in all mix types. Rediset(TM) WMX improves low temperature properties of dense graded mixes at 0.5 percent loading on the asphalt cement. Rediset LQ and Rediset WMX showed good anti stripping properties at 0.5 percent loading on the asphalt cement. The

Effectiveness study on temporary pavement marking removals methods.

DOT National Transportation Integrated Search

2011-06-01

"This study was conducted to identify effective temporary marking removal methods and procedures on concrete and asphalt pavements. Pavement markings provide guidance to road travelers and can lead to accidents when not properly removed. Current stat...

Effectiveness study on temporary pavement marking removals methods.

DOT National Transportation Integrated Search

2011-06-01

This study was conducted to identify effective temporary marking removal methods and procedures on concrete and asphalt pavements. Pavement markings provide guidance to road travelers and can lead to accidents when not properly removed. Current state...

Assessment of Asphalt Concrete Reinforcement Grid in Flexible Pavements

DTIC Science & Technology

2016-05-01

Guide for the Design of Pavement Structures (1993) remains in use and describes in detail the accepted procedures for both the design and maintenance...of pavement structures. Design considerations include pavement perfor- mance, traffic, subgrade soil, construction materials, environment, drain- age...Association of State Highway and Transportation Officials). 1993. Guide for the Design of Pavement Structures. Washington, DC: American Association of

Permeable Pavement Research - Edison, New Jersey

EPA Science Inventory

This presentation provides the background and summary of results collected at the permeable pavement parking lot monitored at the EPA facility in Edison, NJ. This parking lot is surfaced with permeable interlocking concrete pavers (PICP), pervious concrete, and porous asphalt. ...

Implementation and thickness optimization of perpetual pavements in Ohio : [executive summary].

DOT National Transportation Integrated Search

2015-06-01

Perpetual asphalt pavements are designed to confine distresses to the upper layer of the structure, by eliminating : or reducing the potential for fatigue cracking by maintaining the horizontal strains at the bottom of the pavement : below a critical...

Utilization of recycled asphalt concrete with warm mix asphalt and cost-benefit analysis.

PubMed

Oner, Julide; Sengoz, Burak

2015-01-01

The asphalt paving industries are faced with two major problems. These two important challenges are generated with an increase in demand for environmentally friendly paving mixtures and the problem of rapidly rising raw materials. Recycling of reclaimed asphalt pavement (RAP) is a critical necessity to save precious aggregates and reduce the use of costly bitumen. Warm Mix Asphalt (WMA) technology provides not only the option of recycling asphalt pavement at a lower temperature than the temperature maintained in hot mixtures but also encourages the utilization of RAP and therefore saves energy and money. This paper describes the feasibility of utilizing three different WMA additives (organic, chemical and water containing) at recommended contents with different percentages of RAP. The mechanical properties and cost-benefit analysis of WMA containing RAP have been performed and compared with WMA without RAP. The results indicated that, 30%, 10% and 20% can be accepted as an optimum RAP addition related to organic, chemical and water containing additives respectively and organic additive with 30% RAP content has an appreciable increase in tensile strength over the control mix. It was also concluded that the RAP with WMA technology is the ability to reduce final cost compared to HMA and WMA mixtures.

Utilization of Recycled Asphalt Concrete with Warm Mix Asphalt and Cost-Benefit Analysis

PubMed Central

Oner, Julide; Sengoz, Burak

2015-01-01

The asphalt paving industries are faced with two major problems. These two important challenges are generated with an increase in demand for environmentally friendly paving mixtures and the problem of rapidly rising raw materials. Recycling of reclaimed asphalt pavement (RAP) is a critical necessity to save precious aggregates and reduce the use of costly bitumen. Warm Mix Asphalt (WMA) technology provides not only the option of recycling asphalt pavement at a lower temperature than the temperature maintained in hot mixtures but also encourages the utilization of RAP and therefore saves energy and money. This paper describes the feasibility of utilizing three different WMA additives (organic, chemical and water containing) at recommended contents with different percentages of RAP. The mechanical properties and cost-benefit analysis of WMA containing RAP have been performed and compared with WMA without RAP. The results indicated that, 30%, 10% and 20% can be accepted as an optimum RAP addition related to organic, chemical and water containing additives respectively and organic additive with 30% RAP content has an appreciable increase in tensile strength over the control mix. It was also concluded that the RAP with WMA technology is the ability to reduce final cost compared to HMA and WMA mixtures. PMID:25574851

Development of indirect ring tension test for fracture characterization of asphalt mixtures

NASA Astrophysics Data System (ADS)

Zeinali Siavashani, Alireza

Low temperature cracking is a major distress in asphalt pavements. Several test configurations have been introduced to characterize the fracture properties of hot mix (HMA); however, most are considered to be research tools due to the complexity of the test methods or equipment. This dissertation describes the development of the indirect ring tension (IRT) fracture test for HMA, which was designed to be an effective and user-friendly test that could be deployed at the Department of Transportation level. The primary advantages of this innovative and yet practical test include: relatively large fracture surface test zone, simplicity of the specimen geometry, widespread availability of the required test equipment, and ability to test laboratory compacted specimens as well as field cores. Numerical modeling was utilized to calibrate the stress intensity factor formula of the IRT fracture test for various specimen dimensions. The results of this extensive analysis were encapsulated in a single equation. To develop the test procedure, a laboratory study was conducted to determine the optimal test parameters for HMA material. An experimental plan was then developed to evaluate the capability of the test in capturing the variations in the mix properties, asphalt pavement density, asphalt material aging, and test temperature. Five plant-produced HMA mixtures were used in this extensive study, and the results revealed that the IRT fracture test is highly repeatable, and capable of capturing the variations in the fracture properties of HMA. Furthermore, an analytical model was developed based on the viscoelastic properties of HMA to estimate the maximum allowable crack size for the pavements in the experimental study. This analysis indicated that the low-temperature cracking potential of the asphalt mixtures is highly sensitive to the fracture toughness and brittleness of the HMA material. Additionally, the IRT fracture test data seemed to correlate well with the data from

Laboratory evaluation of characteristics of recycled asphalt pavement in Kansas.

DOT National Transportation Integrated Search

2011-09-01

The main objective of this research was to evaluate characteristics of milled Recycled Asphalt : Pavements (RAP) collected from selected milled roadways in Kansas. The RAP was collected from three : selected milled roadways including K-25 in Grant Co...

Study of lime vs. no lime in cold in-place recycled asphalt concrete pavements : final report.

DOT National Transportation Integrated Search

1991-09-01

The resilient characteristics of cold in-place recycled asphalt concrete with and without lime were examined. Six core samples were obtained from a site two months after construction; six months later, six additional core samples were obtained from t...

Improving Quality Control of Asphalt Pavement with RAP Using a Portable Infrared Spectroscopy Device

DOT National Transportation Integrated Search

2016-04-01

This project has investigated the effectiveness of a Portable Infrared Spectrometer (PIRS) device in estimating percent of Reclaimed Asphalt Pavement (RAP) and its contribution into oxidative aging of a new asphalt mixture immediately after productio...

Effect of Material Composition and Environmental Condition on Thermal Characteristics of Conductive Asphalt Concrete.

PubMed

Pan, Pan; Wu, Shaopeng; Hu, Xiaodi; Liu, Gang; Li, Bo

2017-02-23

Conductive asphalt concrete with high thermal conductivity has been proposed to improve the solar energy collection and snow melting efficiencies of asphalt solar collector (ASC). This paper aims to provide some insight into choosing the basic materials for preparation of conductive asphalt concrete, as well as determining the evolution of thermal characteristics affected by environmental factors. The thermal properties of conductive asphalt concrete were studied by the Thermal Constants Analyzer. Experimental results showed that aggregate and conductive filler have a significant effect on the thermal properties of asphalt concrete, while the effect of asphalt binder was not evident due to its low proportion. Utilization of mineral aggregate and conductive filler with higher thermal conductivity is an efficient method to prepare conductive asphalt concrete. Moreover, change in thermal properties of asphalt concrete under different temperature and moisture conditions should be taken into account to determine the actual thermal properties of asphalt concrete. There was no noticeable difference in thermal properties of asphalt concrete before and after aging. Furthermore, freezing-thawing cycles strongly affect the thermal properties of conductive asphalt concrete, due to volume expansion and bonding degradation.

Effect of Material Composition and Environmental Condition on Thermal Characteristics of Conductive Asphalt Concrete

PubMed Central

Pan, Pan; Wu, Shaopeng; Hu, Xiaodi; Liu, Gang; Li, Bo

2017-01-01

Conductive asphalt concrete with high thermal conductivity has been proposed to improve the solar energy collection and snow melting efficiencies of asphalt solar collector (ASC). This paper aims to provide some insight into choosing the basic materials for preparation of conductive asphalt concrete, as well as determining the evolution of thermal characteristics affected by environmental factors. The thermal properties of conductive asphalt concrete were studied by the Thermal Constants Analyzer. Experimental results showed that aggregate and conductive filler have a significant effect on the thermal properties of asphalt concrete, while the effect of asphalt binder was not evident due to its low proportion. Utilization of mineral aggregate and conductive filler with higher thermal conductivity is an efficient method to prepare conductive asphalt concrete. Moreover, change in thermal properties of asphalt concrete under different temperature and moisture conditions should be taken into account to determine the actual thermal properties of asphalt concrete. There was no noticeable difference in thermal properties of asphalt concrete before and after aging. Furthermore, freezing–thawing cycles strongly affect the thermal properties of conductive asphalt concrete, due to volume expansion and bonding degradation. PMID:28772580

Compaction at the longitudinal construction joint in asphalt pavements (KYSPR-00-208)

DOT National Transportation Integrated Search

2002-05-01

Poor compaction practices at longitudinal construction joints in hot-mix asphalt (HMA) pavements lead to premature pavement failure. The hypothesis is that poorly constructed or compacted HMA joints tend to be more permeable and allow water to enter ...

Development of Mix Designs for RAP Concrete for Florida Concrete Test Road

DOT National Transportation Integrated Search

2017-12-01

The main objective of this study was to develop mix designs for concrete incorporating Reclaimed Asphalt Pavement (RAP) materials to be used in the Florida Concrete Test Road. Two different FDOT-approved RAP sources were selected and used in this stu...

Nitrogen Transformations in Three Types of Permeable Pavement

EPA Science Inventory

In 2009, USEPA constructed a 0.4-ha (1-ac) parking lot at the Edison Environmental Center in Edison, NJ, that incorporated three different permeable pavement types - permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA). The driving lanes...

Development of an Image-based Multi-Scale Finite Element Approach to Predict Fatigue Damage in Asphalt Mixtures

NASA Astrophysics Data System (ADS)

Arshadi, Amir

Image-based simulation of complex materials is a very important tool for understanding their mechanical behavior and an effective tool for successful design of composite materials. In this thesis an image-based multi-scale finite element approach is developed to predict the mechanical properties of asphalt mixtures. In this approach the "up-scaling" and homogenization of each scale to the next is critically designed to improve accuracy. In addition to this multi-scale efficiency, this study introduces an approach for consideration of particle contacts at each of the scales in which mineral particles exist. One of the most important pavement distresses which seriously affects the pavement performance is fatigue cracking. As this cracking generally takes place in the binder phase of the asphalt mixture, the binder fatigue behavior is assumed to be one of the main factors influencing the overall pavement fatigue performance. It is also known that aggregate gradation, mixture volumetric properties, and filler type and concentration can affect damage initiation and progression in the asphalt mixtures. This study was conducted to develop a tool to characterize the damage properties of the asphalt mixtures at all scales. In the present study the Viscoelastic continuum damage model is implemented into the well-known finite element software ABAQUS via the user material subroutine (UMAT) in order to simulate the state of damage in the binder phase under the repeated uniaxial sinusoidal loading. The inputs are based on the experimentally derived measurements for the binder properties. For the scales of mastic and mortar, the artificially 2-Dimensional images of mastic and mortar scales were generated and used to characterize the properties of those scales. Finally, the 2D scanned images of asphalt mixtures are used to study the asphalt mixture fatigue behavior under loading. In order to validate the proposed model, the experimental test results and the simulation results were

On the representative volume element of asphalt concrete at low temperature

NASA Astrophysics Data System (ADS)

Marasteanu, Mihai; Cannone Falchetto, Augusto; Velasquez, Raul; Le, Jia-Liang

2016-08-01

The feasibility of characterizing asphalt mixtures' rheological and failure properties at low temperatures by means of the Bending Beam Rheometer (BBR) is investigated in this paper. The main issue is the use of thin beams of asphalt mixture in experimental procedures that may not capture the true behavior of the material used to construct an asphalt pavement.

Testing and analysis of LWT and SCB properties of asphalt concrete mixtures.

DOT National Transportation Integrated Search

2016-04-01

Currently, Louisianas Quality Control and Quality Assurance (QC/QA) practice for asphalt mixtures in : pavement construction is mainly based on controlling properties of plant produced mixtures that include : gradation and asphalt content, voids f...

A Research on Low Modulus Distributed Fiber Optical Sensor for Pavement Material Strain Monitoring

PubMed Central

Meng, Lingjian; Wang, Linbing; Hou, Yue; Yan, Guannan

2017-01-01

The accumulated irreversible deformation in pavement under repeated vehicle loadings will cause fatigue failure of asphalt concrete. It is necessary to monitor the mechanical response of pavement under load by using sensors. Previous studies have limitations in modulus accommodation between the sensor and asphalt pavement, and it is difficult to achieve the distributed monitoring goal. To solve these problems, a new type of low modulus distributed optical fiber sensor (DOFS) for asphalt pavement strain monitoring is fabricated. Laboratory experiments have proved the applicability and accuracy of the newly-designed sensor. This paper presents the results of the development. PMID:29048393

A Research on Low Modulus Distributed Fiber Optical Sensor for Pavement Material Strain Monitoring.

PubMed

Meng, Lingjian; Wang, Linbing; Hou, Yue; Yan, Guannan

2017-10-19

The accumulated irreversible deformation in pavement under repeated vehicle loadings will cause fatigue failure of asphalt concrete. It is necessary to monitor the mechanical response of pavement under load by using sensors. Previous studies have limitations in modulus accommodation between the sensor and asphalt pavement, and it is difficult to achieve the distributed monitoring goal. To solve these problems, a new type of low modulus distributed optical fiber sensor (DOFS) for asphalt pavement strain monitoring is fabricated. Laboratory experiments have proved the applicability and accuracy of the newly-designed sensor. This paper presents the results of the development.

Evaluation of asphalt additives to resist permanent pavement deformation.

DOT National Transportation Integrated Search

1989-01-01

Many new asphalt additives reportedly improve the stability and flexibility of asphalt concrete, which leads to increased service life. Four polymers (Polybilt 100, Styrelf 13, Downright HM 100L, and Ultrapave 70) and a diatomaceous filler (Celite 29...

Measurement of the pore size distribution of limestone aggregates in concrete pavement cores : phase I.

DOT National Transportation Integrated Search

2012-04-01

Freeze-thaw damage is one of the common forms of distress for concrete pavements in Kansas. D-Cracking is a form of : freeze-thaw damage caused by aggregates with poor freeze-thaw durability. It is believed that pores in the aggregates below : 10 m...

Development of a non-solvent based test method for evaluating reclaimed asphalt pavement mixes.

DOT National Transportation Integrated Search

2004-09-01

The percent of reclaimed asphalt pavement (RAP) used in hot mix asphalt (HMA) is currently established either by arbitrarily setting maximum percent limits, or alternatively, by evaluating both the virgin and recovered binder properties. The first ap...

Controlling conductivity of asphalt concrete with graphite.

DOT National Transportation Integrated Search

2014-08-01

Electrically conductive asphalt concrete has a huge potential for various multifunctional applications such as : self-healing, self-sensing, and deicing. In order to utilize the full spectrum of applications of electrically conductive : asphalt compo...

78 FR 26847 - Including Specific Pavement Types in Federal-aid Highway Traffic Noise Analyses

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-08

... traffic noise analyses. Current highway traffic noise analyses rely on data from three pavement types: dense-graded asphaltic concrete (DGAC), open-graded asphaltic concrete (OGAC), and Portland cement... noise analyses provide data for decisionmakers to make informed decisions on project alternatives and...

Development of a semicircular bend (SCB) test method for performance testing of Nebraska asphalt mixtures.

DOT National Transportation Integrated Search

2015-12-01

Granted that most distresses in asphalt (flexible) concrete (AC) pavements are directly related to fracture, it becomes clear : that identifying and characterizing fracture properties of AC mixtures is a critical step towards a better pavement design...

The use of a non-nuclear density gauge for monitoring the compaction process of asphalt pavement

NASA Astrophysics Data System (ADS)

Van den bergh, Wim; Vuye, Cedric; Kara, Patricia; Couscheir, Karolien; Blom, Johan; Van Bouwel, Philippe

2017-09-01

The mechanical performance of an asphalt pavement affects its durability - thus carbon footprint. Many parameters contribute to the success of a durable asphalt mix, e.g. material selection, an accurate mix and even the road design in which the asphalt mix quality is quantified. The quality of the asphalt mix, by its mechanical properties, is also related to the compaction degree. However, and specifically for high volume rates, the laying process at the construction site needs an effective method to monitor and adjust immediately the compaction quality before cooling and without damaging the layer, which is now absent. In this paper the use of a non-nuclear density gauge (PQI - Pavement Quality Indicator) is evaluated, based on a site at Brussels Airport. Considering the outcome of the present research, this PQI is advised as a unique tool for continuous density measurements and allow immediate adjustments during compaction, and decreases the number of core drilling for quality control, and as a posteriori asphalt pavement density test where cores are prohibited. The use of PQI could be recommended to be a part of the standard quality control process in the Flemish region.

Wear resistant pavement study.

DOT National Transportation Integrated Search

2009-01-01

This report documents the construction of three special pavement test sections on I-90 east of Spokane, Washington. The test sections included ultra-thin and thin whitetopping, Modified Class D open graded asphalt concrete, and micro/macro surfacing ...

Runoff initiation from falling raindrops - comparison of smooth impervious surface and asphalt pavements. Effects of surface inclination and texture.

NASA Astrophysics Data System (ADS)

Nezlobin, David; Pariente, Sarah; Lavee, Hanoch; Sachs, Eyal; Levenberg, Eyal

2017-04-01

The processes of runoff initiation on smooth impervious surfaces and various asphalt pavements are investigated in laboratory rain simulator experiments and outdoor sprinkling tests. Visual and FLIR observations indicate that runoff initiation is associated with coalescence of drop clusters on the surface and complex changes in micro-connectivity. Depending on surface inclination, several morphological regimes of flow initiation have been observed. In the case of very small inclination the runoff initiation is governed by critical merging of drop clusters on the surface and develops in broad flows (very abrupt, but delayed). For larger inclinations, the runoff occurs in rivulets or strongly directed flow threads. On asphalt pavements the runoff initiation is also strongly affected by pavement SVF (Surface Void Fraction), texture and even by the asphalt hydrophobicity. A simplified bi-level model of the pavement surface may explain principal differences in the runoff initiation on asphalts with small, intermediate and large SVF values. For small SVF (standard fresh asphalts) the runoff develops on the upper surface level, and filling of the surface voids is not always required (especially for the large inclinations). For intermediate SVF (considerably deteriorated asphalts) the runoff develops as well on the upper surface level, but only after considerable filling of the surface voids. Finally, on severely deteriorated asphalts (very large SVFs) the runoff develops on the "bottom" level of asphalt surface, after only partial filling of the surface voids. Other factors, such as drops splash and splitting, also affect the process of runoff initiation and explain rather considerable differences (sometimes of 2-3 mm rain depth) in the runoff thresholds on various non-porous asphalt pavements. Similar phenomena can be probably observed on certain types of rock outcrops.

Application of high performance concrete in the pavement system : structural response of high performance concrete pavement : executive summary.

DOT National Transportation Integrated Search

2002-01-01

Rigid pavements make up a significant percentage of highway systems in the United States and abroad. Concrete pavements provide an economical and durable solution for highway systems, because the pavements last longer and require less maintenance. Re...

Reflective cracking control : interim report - fourth year.

DOT National Transportation Integrated Search

1999-07-01

Reflective cracking has long been considered a major problem associated with asphalt : pavements. Several methods including milling, crack sealing and fabric membranes have : been used in an attempt to eliminate or delay the reflective cracking proce...

Effects of two warm-mix additives on aging, rheological and failure properties of asphalt cements

NASA Astrophysics Data System (ADS)

Omari, Isaac Obeng

Sustainable road construction and maintenance could be supported when excellent warm-mix additives are employed in the modification of asphalt. These warm-mix additives provide remedies for today's requirements such as fatigue cracking resistance, durability, thermal cracking resistance, rutting resistance and resistance to moisture damage. Warm-mix additives are based on waxes and surfactants which reduce energy consumption and carbon dioxide emissions significantly during the construction phase of the pavement. In this study, the effects of two warm mix additives, siloxane and oxidised polyethylene wax, on roofing asphalt flux (RAF) and asphalt modified with waste engine oil (655-7) were investigated to evaluate the rheological, aging and failure properties of the asphalt binders. In terms of the properties of these two different asphalts, RAF has proved to be superior quality asphalt whereas 655-7 is poor quality asphalt. The properties of the modified asphalt samples were measured by Superpave(TM) tests such as Dynamic Shear Rheometer (DSR) test and Bending Beam Rheometer (BBR) test as well as modified protocols such as the extended BBR (eBBR) test (LS-308) and the Double- Edge-Notched Tension (DENT) test (LS-299) after laboratory aging. In addition, the Avrami theory was used to gain an insight on the crystallization of asphalt or the waxes within the asphalt binder. This study has however shown that the eBBR and DENT tests are better tools for providing accurate specification tests to curb thermal and fatigue cracking in contemporary asphalt pavements.

Analysis, testing and verification of the behavior of composite pavements under Florida conditions using a heavy vehicle simulator

NASA Astrophysics Data System (ADS)

Tapia Gutierrez, Patricio Enrique

Whitetopping (WT) is a rehabilitation method to resurface deteriorated asphalt pavements. While some of these composite pavements have performed very well carrying heavy load, other have shown poor performance with early cracking. With the objective of analyzing the applicability of WT pavements under Florida conditions, a total of nine full-scale WT test sections were constructed and tested using a Heavy Vehicle Simulator (HVS) in the APT facility at the FDOT Material Research Park. The test sections were instrumented to monitor both strain and temperature. A 3-D finite element model was developed to analyze the WT test sections. The model was calibrated and verified using measured FWD deflections and HVS load-induced strains from the test sections. The model was then used to evaluate the potential performance of these test sections under critical temperature-load condition in Florida. Six of the WT pavement test sections had a bonded concrete-asphalt interface by milling, cleaning and spraying with water the asphalt surface. This method produced excellent bonding at the interface, with shear strength of 195 to 220 psi. Three of the test sections were intended to have an unbonded concrete-asphalt interface by applying a debonding agent in the asphalt surface. However, shear strengths between 119 and 135 psi and a careful analysis of the strain and the temperature data indicated a partial bond condition. The computer model was able to satisfactorily model the behavior of the composite pavement by mainly considering material properties from standard laboratory tests and calibrating the spring elements used to model the interface. Reasonable matches between the measured and the calculated strains were achieved when a temperature-dependent AC elastic modulus was included in the analytical model. The expected numbers of repetitions of the 24-kip single axle loads at critical thermal condition were computed for the nine test sections based on maximum tensile stresses