DETAIL VIEW OF LOWER TRAM TERMINAL, SECONDARY ORE BIN, CRUSHER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF LOWER TRAM TERMINAL, SECONDARY ORE BIN, CRUSHER FOUNDATION, AND BALL MILL FOUNDATIONS, LOOKING NORTH NORTHWEST. ORE FROM THE MINES WAS DUMPED FROM THE TRAM BUCKETS INTO THE PRIMARY ORE BIN UNDER THE TRAM TERMINAL. A SLIDING CONTROL DOOR INTRODUCED THE INTO THE JAW CRUSHER (FOUNDATIONS,CENTER). THE CRUSHED ORE WAS THEN CONVEYED INTO THE SECONDARY ORE BIN AT CENTER LEFT. A HOLE IN THE FLOOR OF THE ORE BIN PASSED ORE ONTO ANOTHER CONVEYOR THAT BROUGHT IT OUT TO THE BALL MILL(FOUNDATIONS,CENTER BOTTOM). THIS SYSTEM IS MOST LIKELY NOT THE ORIGINAL SET UP, PROBABLY INSTALLED IN THE MINE'S LAST OCCUPATION IN THE EARLY 1940s. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Effects of eddy currents on selective spectral editing experiments at 3T.

PubMed

Oeltzschner, Georg; Snoussi, Karim; Puts, Nicolaas A; Mikkelsen, Mark; Harris, Ashley D; Pradhan, Subechhya; Tsapkini, Kyrana; Schär, Michael; Barker, Peter B; Edden, Richard A E

2018-03-01

To investigate frequency-offset effects in edited magnetic resonance spectroscopy (MRS) experiments arising from B 0 eddy currents. Macromolecule-suppressed (MM-suppressed) γ-aminobutyric acid (GABA)-edited experiments were performed at 3T. Saturation-offset series of MEGA-PRESS experiments were performed in phantoms, in order to investigate different aspects of the relationship between the effective editing frequencies and eddy currents associated with gradient pulses in the sequence. Difference integrals were quantified for each series, and the offset dependence of the integrals was analyzed to quantify the difference in frequency (Δf) between the actual vs. nominal expected saturation frequency. Saturation-offset N-acetyl-aspartate-phantom experiments show that Δf varied with voxel orientation, ranging from 10.4 Hz (unrotated) to 6.4 Hz (45° rotation about the caudal-cranial axis) and 0.4 Hz (45° rotation about left-right axis), indicating that gradient-related B 0 eddy currents vary with crusher-gradient orientation. Fixing the crusher-gradient coordinate-frame substantially reduced the orientation dependence of Δf (to ∼2 Hz). Water-suppression crusher gradients also introduced a frequency offset, with Δf = 0.6 Hz ("excitation" water suppression), compared to 10.2 Hz (no water suppression). In vivo spectra showed a negative edited "GABA" signal, suggesting Δf on the order of 10 Hz; with fixed crusher-gradient coordinate-frame, the expected positive edited "GABA" signal was observed. Eddy currents associated with pulsed field gradients may have a considerable impact on highly frequency-selective spectral-editing experiments, such as MM-suppressed GABA editing at 3T. Careful selection of crusher gradient orientation may ameliorate these effects. 2 Technical Efficacy: Stage 1 J. Magn. Reson. Imaging 2018;47:673-681. © 2017 International Society for Magnetic Resonance in Medicine.

Engineering and organizational solutions for improvement of engineering and economic characteristics of the TPE-216 boilers equipped with MV-3300/800/490 pulverizing fans

NASA Astrophysics Data System (ADS)

Kirillov, M. V.; Safronov, P. G.

2014-07-01

Efficiency of coal-fired boilers is determined in many respects by optimal operation of the coal-pulverizing plants that are increasingly frequently equipped with pulverizing fans. By an example of retrofitted MV-3300/800/490 pulverizing fans, the effects of different factors on the performance and economic efficiency of the coal-pulverizing plants are analyzed. The experience gained in retrofitting MV-3300/800/490 pulverizing fans by introducing the three-crusher operation mode of a TPE-216 boiler employing the internal recirculation and a blading device in the classifier was also studied. Optimization of the boiler's operation mode was made when switching over from the four-crusher to the three-crusher mode, which considerably improved the engineering and economic characteristics.

Development of 300 mesh Soy Bean Crusher for Tofu Material Processing

NASA Astrophysics Data System (ADS)

Lee, E. S.; Pratama, P. S.; Supeno, D.; Jeong, S. W.; Byun, J. Y.; Woo, J. H.; Park, C. S.; Choi, W. S.

2018-03-01

A machine such as bean crusher machine is subjected to different loads and vibration. Due to this vibration there will be certain deformations which affect the performance of the machine in adverse manner. This paper proposed a vibration analysis of bean crusher machine using ANSYS. The effect of vibration on the structure was studied in order to ensure the safety using finite element analysis. This research supports the machine designer to create a better product with lower cost and faster development time. To do this, firstly, using Inventor, a CAD model is prepared. Secondly, the analysis is to be carried out using ANSYS 15. The modal analysis and random vibration analysis of the structure was conducted. The analysis shows that the proposed design was successfully shows the minimum deformation when the vibration was applied in normal condition.

45. VIEW OF UPPER LEVEL CRUSHER ADDITION FROM CRUSHED OXIDIZED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. VIEW OF UPPER LEVEL CRUSHER ADDITION FROM CRUSHED OXIDIZED ORE BIN. 18 INCH BELT CONVEYOR BIN FEED, LOWER CENTER, WITH STEPHENS-ADAMSON 25 TON/HR ELEVATOR SPLIT DISCHARGE (OXIDIZED/UNOXIDIZED) IN CENTER. CRUDE ORE BINS AND MACHINE SHOP BEYOND. NOTE TOP OF CRUSHED OXIDIZED ORE BIN IS BELOW TOP OF CRUDE ORE BINS. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

43. INTERIOR VIEW, CRUSHING ADDITION. THE SYMONS VIBRATING SCREEN SITS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. INTERIOR VIEW, CRUSHING ADDITION. THE SYMONS VIBRATING SCREEN SITS ON TOP OF THE PLATFORM. OVERSIZE ORE IS FED BY CHUTE TO THE GYRATORY SECONDARY CRUSHER (MISSING) SITTING ON CONCRETE FOUNDATIONS TO LOWER RIGHT. UNDERSIZE ORE WAS FED BY THE LOWER CHUTE (CENTER LEFT) TO THE 24 INCH BELT CONVEYOR UNDER THE SECONDARY CRUSHER. THE DRYER ROOM IS BEYOND. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Drug loss while crushing tablets: Comparison of 24 tablet crushing devices

PubMed Central

Thong, Min Yew; Manrique, Yady J.

2018-01-01

This study investigated 24 tablet crushing devices for drug loss using different methods to recover the crushed tablet. 24 devices were compared: 3 with disposable cups, 6 with disposable bags, 12 without separate vessels and 3 types of mortar and pestle. One paracetamol tablet was crushed and recovered by tapping the powder out. Where appropriate, depending on crusher size and manufacturer instructions, the powder was also recovered by mixing with water or food. Paracetamol recovery (quantity that can be delivered to a patient) and leftover (quantity remaining in the device) were measured using a validated UV method and the entire experiment was replicated 3 times. Drug recovery ranged from 86.7–98.1% when the crushed tablet was tapped out of the crushers (average loss 5.8%). Significant losses were measured for 18 crushers, particularly manually operated hand-twist crushers with a serrated crushing surface, and some devices with disposable bags or cups. Rinsing the crushed powder with water once resulted in an average of 24.2% drug loss, and this was reduced to 4.2% after a second rinse. If crushing is unavoidable, maximizing medication delivery to the patient is essential. Rinsing twice resulted in similar paracetamol recovery to tapping the powder out; however only water rinses have the potential for direct consumption by the patient, minimizing drug loss across the entire crushing and transfer process. PMID:29494695

51. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS BAKER COOLER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

51. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS BAKER COOLER AT LOWER LEFT, AND FOUNDATIONS FOR ROD MILL BETWEEN COOLER AND STEPHENS-ADAMSON INCLINED BUCKET ELEVATOR. THE BELT CONVEYOR TO RIGHT OF ELEVATOR FED ELEVATOR FROM ROD MILL. 100-TON ORE BIN AND DUST COLLECTOR IS BEHIND FRAMING BENT. NOTE CONVEYOR EMERGING FROM BOTTOM OF ORE BIN, THIS AND THE INCLINED ELEVATOR FED THE SYMONS SCREEN (MISSING). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

37. VIEW NORTH FROM EAST CRUDE ORE BIN TO CRUSHER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. VIEW NORTH FROM EAST CRUDE ORE BIN TO CRUSHER ADDITION AND CRUSHED OXIDIZED ORE BIN. VISIBLE ARE DINGS MAGNETIC PULLEY (CENTER), THE 100-TON STEEL CRUSHED UNOXIDIZED ORE BIN, AND UPPER PORTION OF THE STEPHENS-ADAMSON 25 TON/HR BUCKET ELEVATOR. THE UPPER TAILINGS POND LIES BEYOND THE MILL WITH THE UPPER TAILINGS DAM UNDER THE GRAVEL ROAD IN THE UPPER RIGHT CORNER. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

50. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS 100TON STEEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

50. VIEW OF CRUSHER ADDITION FROM EAST. SHOWS 100-TON STEEL UNOXIDIZED ORE BIN, STEPHENS-ADAMSON 15 TON/HR INCLINED BUCKET ELEVATOR, AND DUST COLLECTION BIN IN UPPER RIGHT QUADRANT. THE ROD MILL CIRCUIT STOOD IN FRONT OF THE BUCKET ELEVATOR AND BEHIND THE BAKER COOLER (LEFT CENTER). MILL SOLUTION TANKS WERE IN FRONT OF THE CRUSHED OXIDIZED ORE BIN (CENTER), AND THE MILL FLOOR WAS THE NEXT LEVEL DOWN (RIGHT). - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

41. VIEW NORTH OF UPPER LEVEL OF CRUSHER ADDITION. DINGS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. VIEW NORTH OF UPPER LEVEL OF CRUSHER ADDITION. DINGS MAGNETIC PULLEY AT CENTER. ALSO SHOWS 100-TON CRUSHED UNOXIDIZED ORE BIN (RIGHT), PULLEY FORM 18 INCH BELT CONVEYOR CRUSHED OXIDIZED ORE BIN FEED AND STEPHENSADAMSON 25 TON/HR BUCKET ELEVATOR (UPPER CENTER). THE UPPER PORTION OF THE SAMPLING ELEVATOR IS ABOVE THE MAGNETIC PULLEY (CENTER LEFT) WITH THE ROUTE OF THE 16 INCH BELT CONVEYOR FINES FEED TO CRUSHED OXIDIZED ORE BIN TO ITS LEFT. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Influence of olive ripening degree and crusher typology on chemical and sensory characteristics of Correggiolo virgin olive oil.

PubMed

Morrone, Lucia; Pupillo, Sabrina; Neri, Luisa; Bertazza, Giampaolo; Magli, Massimiliano; Rotondi, Annalisa

2017-03-01

In this study, two types of crusher, hammer and blade, were used to produce olive oils from cv. Correggiolo olives at four stages of ripeness, to analyse the effect of these two factors on oil quality indices (free acidity, peroxide value, UV absorption), on phenolic compounds content and sensory profiles. Differences in chemical and sensory data were analysed by two-way ANOVA. Ripeness exerted a stronger influence than the crushing equipment on quality indices, phenolic content and sensory evaluation; moreover the statistical significance of interaction between the factors considered suggests that they are intertwined. Differences in the texture of olive pastes obtained by squashing and crushing were clearly evident at the first stage of ripeness via observation with a scanning electron microscope. The stronger mechanical action of the hammer crusher also produced smaller pit fragments compared to the blade crusher, as shown by particle size analysis of the kernels fragments. Knowledge about the interaction between ripening and crushing will allow olive oil producers to pursue a product of the quality most suitable for a particular type of consumer. For example, bitterness and pungency, characters recently connected with health effects because sensory markers of extra virgin olive oil (EVOO) polyphenols, do not have a great sensory appeal for most consumers; however, there is a niche of gourmet estimators interested in these peculiar flavours and ready to pay a premium price for them. The producer will be able to customise the EVOO by modulating its chemical and sensory characteristics, especially the phenolic fraction, thus addressing the needs of consumers with different tastes. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Airborne particles released by crushing CNT composites

NASA Astrophysics Data System (ADS)

Ogura, I.; Okayama, C.; Kotake, M.; Ata, S.; Matsui, Y.; Gotoh, K.

2017-06-01

We investigated airborne particles released as a result of crushing carbon nanotube (CNT) composites using a laboratory scale crusher with rotor blades. For each crushing test, five pellets (approximately 0.1 g) of a polymer (polystyrene, polyamide, or polycarbonate) containing multiwall CNTs (Nanocyl NC7000 or CNano Flotube9000) or no CNTs were placed in the container of the crusher. The airborne particles released by the crushing of the samples were measured. The real-time aerosol measurements showed increases in the concentration of nanometer- and micrometer-sized particles, regardless of the sample type, even when CNT-free polymers were crushed. The masses of the airborne particles collected on filters were below the detection limit, which indicated that the mass ratios of the airborne particles to the crushed pellets were lower than 0.02%. In the electron microscopic analysis, particles with protruding CNTs were observed. However, free-standing CNTs were not found, except for a poorly dispersed CNT-polystyrene composite. This study demonstrated that the crushing test using a laboratory scale crusher is capable of evaluating the potential release of CNTs as a result of crushing CNT composites. The advantage of this method is that only a small amount of sample (several pieces of pellets) is required.

Effect of air and noise pollution on species diversity and population density of forest birds at Lalpahari, West Bengal, India.

PubMed

Saha, Dulal C; Padhy, Pratap K

2011-11-15

The Rajmahal-type quality stones for building purposes are found abundantly in Birbhum district, West Bengal, India, where stone mining and crushing have become the main industrial activity. Although crusher dust is injurious to health, demand for crushed stone is ever-increasing as a result of rapid infrastructural growth in the country. Most of the crusher units at Rampurhat are situated along the roadways adjacent to forest under Tumboni Beat of Rampurhat Range of Birbhum Forest Division. Excessive load of air pollution in this area has led to degradation of this forest. The status of the ambient air and noise level was evaluated. The effect of air and noise pollution on abundance and variability of birds in this forest have been compared to an almost non-polluted forest of the same bio-geographic zone. Both species diversity and population density of birds were found to decrease in the polluted forest, especially in the areas adjacent to crushers. For comparing the pollution status of two different forest sites and for establishing whether the density of birds have any correlation between the sites, the Student's t-test and the chi-square test were applied respectively. Most of the results proved to be significant. Copyright © 2011 Elsevier B.V. All rights reserved.

Creative Practice : Design and Manufacturing of ‘CD Crusher’

NASA Astrophysics Data System (ADS)

Yamamoto, Koji; Senda, Shinkoh; Fukumori, Tsutom; Sato, Kazuo

A practice program for graduate students in mechanical engineering has been developed. The task of this training is to design and manufacture an original ‘CD crusher’ , a machine to mechanically destroy compact disks after use. This is a competition among groups of students creating their original CD crusher which fulfills the regulation. The regulation is that the crusher has to use rotational blades cutting the CDs. Same sized blades are supplied to the students groups. They are fabricated from a steel bar through cutting, annealing and quenching processes by the presence of students. Technical staffs are ready to help students on the whole way of the practice. However, they encourage initiative by the students from planning to manufacturing. Students satisfied at the practice according to the comments after competition.

Design of crusher liner based on time - varying uncertainty theory

NASA Astrophysics Data System (ADS)

Tang, J. C.; Shi, B. Q.; Yu, H. J.; Wang, R. J.; Zhang, W. Y.

2017-09-01

This article puts forward the time-dependent design method considering the load fluctuation factors for the liner based on the time-varying uncertainty theory. In this method, the time-varying uncertainty design model of liner is constructed by introducing the parameters that affect the wear rate, the volatility and the drift rate. Based on the design example, the timevarying design outline of the moving cone liner is obtained. Based on the theory of minimum wear, the gap curve of wear resistant cavity is designed, and the optimized cavity is obtained by the combination of the thickness of the cone and the cavity gap. Taking the PYGB1821 multi cylinder hydraulic cone crusher as an example, it is proved that the service life of the new liner is improved by more than 14.3%.

Air cleaning performance of a new environmentally controlled primary crusher operator booth.

PubMed

Organiscak, J A; Cecala, A B; Zimmer, J A; Holen, B; Baregi, J R

2016-02-01

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company's Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system's effectiveness in controlling airborne dusts and particulates. The booth's dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-μm respirable size particulates under various HVAC airflow operating conditions.

30 CFR 46.8 - Annual refresher training.

Code of Federal Regulations, 2014 CFR

2014-07-01

...; transportation controls and communication systems; escape and emergency evacuation plans, firewarning and... accidents; health; explosives; and respiratory devices. Training is also recommended on the hazards... tractors); conveyor systems; cranes; crushers; excavators; and dredges. Other recommended subjects include...

30 CFR 46.8 - Annual refresher training.

Code of Federal Regulations, 2012 CFR

2012-07-01

...; transportation controls and communication systems; escape and emergency evacuation plans, firewarning and... accidents; health; explosives; and respiratory devices. Training is also recommended on the hazards... tractors); conveyor systems; cranes; crushers; excavators; and dredges. Other recommended subjects include...

30 CFR 46.8 - Annual refresher training.

Code of Federal Regulations, 2013 CFR

2013-07-01

...; transportation controls and communication systems; escape and emergency evacuation plans, firewarning and... accidents; health; explosives; and respiratory devices. Training is also recommended on the hazards... tractors); conveyor systems; cranes; crushers; excavators; and dredges. Other recommended subjects include...

30 CFR 46.8 - Annual refresher training.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; transportation controls and communication systems; escape and emergency evacuation plans, firewarning and... accidents; health; explosives; and respiratory devices. Training is also recommended on the hazards... tractors); conveyor systems; cranes; crushers; excavators; and dredges. Other recommended subjects include...

Air cleaning performance of a new environmentally controlled primary crusher operator booth

PubMed Central

Organiscak, J.A.; Cecala, A.B.; Zimmer, J.A.; Holen, B.; Baregi, J.R.

2016-01-01

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-μm respirable size particulates under various HVAC airflow operating conditions. PMID:26937052

7 CFR 981.442 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., pieces of kernels, meal accumulated in manufacturing, or other material, to crushers, feed manufacturers... contamination in accordance with the provisions of this section. (1) Treatment process. Treatment processes... Salmonella bacteria in almonds, pursuant to a letter of determination issued by the Food and Drug...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Loading, Hauling, and Dumping Safety... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

15. VIEW OF COAL TRESTLE LOOKING NORTHEAST. COAL DUMPED FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. VIEW OF COAL TRESTLE LOOKING NORTHEAST. COAL DUMPED FROM HOPPER CARS COULD BE CRUSHED AND LOADED ON A CONVEYOR THAT PARALLELED THE TRACK TO THE EAST (LEFT) AND CARRIED IT TO A 1000 TON BUNKER LOCATED ON THE NORTH SIDE OF THE EAST BOILER ROOM. COAL COULD ALSO GO THROUGH THE CRUSHER AND BE DIVERTED TO THE CONVEYOR SHOWN IN THE LEFT FOREGROUND. COAL PILES FORMED UNDER THE CONVEYOR WOULD BE MOVED AND SHAPED BY BULLDOZER. A GROUND LEVEL HOPPER WAS LOCATED TO THE RIGHT OF THE SLOPING HOUSING WHICH EXTENDS FROM THE SOUTH SIDE OF THE COAL TRESTLE. THIS HOPPER FED A CONVEYOR LOCATED WITHIN THE SLOPING HOUSING. COAL DROPPED INTO THE HOPPER WOULD BE CONVEYED INTO THE CRUSHER UNDER THE TRESTLE AND THEN DIVERTED TO THE CONVEYOR WHICH LOADED THE 1000 TON BUNKER. THE COAL HANDLING SYSTEM WAS DESIGNED BY GIBBS AND HILL IN 1947. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Impact of industrial hammer mill rotor speed on extraction efficiency and quality of extra virgin olive oil.

PubMed

Polari, Juan J; Garcí-Aguirre, David; Olmo-García, Lucía; Carrasco-Pancorbo, Alegría; Wang, Selina C

2018-03-01

Crushing is a key step during olive oil extraction. Among commercial crushers, the hammer mill is the most widely used due to its robustness and high throughput. In the present work, the impact of hammer mill rotor speed on extraction yield and overall quality of super-high-density Arbosana olive oils were assessed in an industrial facility. Our results show that increasing the rotor speed from 2400rpm to 3600rpm led to a rise in oil yield of 1.2%, while conserving quality parameters. Sensory analysis showed more pungency with increased rotation speed, while others attributes were unaffected. Volatile compounds showed little variation with the differences in crusher speed; however, total phenols content, two relevant secoiridoids, and triterpenoids levels increased with rotor speed. Hammer mill rotor speed is a processing variable that can be tuned to increase the extraction efficiency and modulate the chemical composition of extra virgin olive oil. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimal control of the signal-to-noise ratio per unit time of a spin 1/2 particle: The crusher gradient and the radiation damping cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lapert, M.; Glaser, S. J.; Assémat, E.

We show to which extent the signal to noise ratio per unit time of a spin 1/2 particle can be maximized. We consider a cyclic repetition of experiments made of a measurement followed by a radio-frequency magnetic field excitation of the system, in the case of unbounded amplitude. In the periodic regime, the objective of the control problem is to design the initial state of the system and the pulse sequence which leads to the best signal to noise performance. We focus on two specific issues relevant in nuclear magnetic resonance, the crusher gradient and the radiation damping cases. Optimalmore » control techniques are used to solve this non-standard control problem. We discuss the optimality of the Ernst angle solution, which is commonly applied in spectroscopic and medical imaging applications. In the radiation damping situation, we show that in some cases, the optimal solution differs from the Ernst one.« less

15. NORTH ELEVATION OF UPPER ORE BIN, CHUTE, AND JAW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. NORTH ELEVATION OF UPPER ORE BIN, CHUTE, AND JAW CRUSHER, LOOKING SOUTH FROM END OF CONVEYOR PLATFORM. NOTICE THE THREE ORE BIN CONTROL DOORS, CORRESPONDING TO SEPARATE COMPARTMENTS OF THE BIN. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

40 CFR 60.670 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... mineral processing plants: each crusher, grinding mill, screening operation, bucket elevator, belt... grinding mills at hot mix asphalt facilities that reduce the size of nonmetallic minerals embedded in... or grinding mills above ground; and wet material processing operations (as defined in § 60.671). (b...

30 CFR 57.14110 - Flying or falling materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Flying or falling materials. 57.14110 Section... and Equipment Safety Devices and Maintenance Requirements § 57.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors...

30 CFR 56.14110 - Flying or falling materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Flying or falling materials. 56.14110 Section... Equipment Safety Devices and Maintenance Requirements § 56.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors present a...

30 CFR 56.14110 - Flying or falling materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Flying or falling materials. 56.14110 Section... Equipment Safety Devices and Maintenance Requirements § 56.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors present a...

30 CFR 57.14110 - Flying or falling materials.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Flying or falling materials. 57.14110 Section... and Equipment Safety Devices and Maintenance Requirements § 57.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors...

30 CFR 57.14110 - Flying or falling materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Flying or falling materials. 57.14110 Section... and Equipment Safety Devices and Maintenance Requirements § 57.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors...

30 CFR 56.14110 - Flying or falling materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Flying or falling materials. 56.14110 Section... Equipment Safety Devices and Maintenance Requirements § 56.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors present a...

30 CFR 57.14110 - Flying or falling materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Flying or falling materials. 57.14110 Section... and Equipment Safety Devices and Maintenance Requirements § 57.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors...

30 CFR 56.14110 - Flying or falling materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Flying or falling materials. 56.14110 Section... Equipment Safety Devices and Maintenance Requirements § 56.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors present a...

30 CFR 56.14110 - Flying or falling materials.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Flying or falling materials. 56.14110 Section... Equipment Safety Devices and Maintenance Requirements § 56.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors present a...

30 CFR 57.14110 - Flying or falling materials.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Flying or falling materials. 57.14110 Section... and Equipment Safety Devices and Maintenance Requirements § 57.14110 Flying or falling materials. In areas where flying or falling materials generated from the operation of screens, crushers, or conveyors...

30 CFR 57.9315 - Dust control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Dust control. 57.9315 Section 57.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....9315 Dust control. Dust shall be controlled at muck piles, material transfer points, crushers, and on...

30 CFR 57.9315 - Dust control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Dust control. 57.9315 Section 57.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....9315 Dust control. Dust shall be controlled at muck piles, material transfer points, crushers, and on...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

30 CFR 56.9315 - Dust control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Dust control. 56.9315 Section 56.9315 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... control. Dust shall be controlled at muck piles, material transfer points, crushers, and on haulage roads...

77 FR 38087 - Agency Information Collection Activities; Submission for OMB Review; Comment Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-26

... protective equipment to protect miners from harmful levels of noise that can result in hearing loss. However..., relies on drills, crushers, compressors, conveyors, trucks, loaders, and other heavy-duty equipment for the excavation, haulage, and processing of material. This equipment creates high sound levels...

Performance Evaluation Test of the Orbit Screen Model 68A and the Komplet Model 48-25 Rock Crusher

DTIC Science & Technology

2008-08-01

two representatives from the Government of Ecuador, Ms . Viviana Anabela Meza Cevallos, from the Demining Center of Ecuador, and Lieutenant Jose Luis...Mines ( MRMs ) Antipersonnel Simulants............................ 8 4 Orbit Screen Model 68 Testing...Mock Mine .............................................................................................................. 7 Figure 8: MRM Simulant, Type

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OBLIQUE DETAIL VIEW OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. THE JAW CRUSHER FOUNDATION CAN BE CLEARLY SEEN AT CENTER LEFT WITH A CONVEYOR TO CARRY CRUSHED ORE UP TO THE SECONDARY ORE BIN,LEFT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

26 CFR 48.4061(a)-1 - Imposition of tax; exclusion for light-duty trucks, etc.

Code of Federal Regulations, 2010 CFR

2010-04-01

... on the highway; machinery or equipment used solely in the operation of mobile amusement rides; television equipment mounted in a mobile television studio; machine shop equipment mounted in a mobile machine shop; and car crushing equipment mounted on the chassis of a mobile car crusher. (4) Passenger...

Measuring How Muscles Function in Levers.

ERIC Educational Resources Information Center

DeMont, M. Edwin

1996-01-01

Presents an exercise that examines the lever systems that function in the chelae of the American lobster. Involves calculating the mechanical and distance advantages of the crusher and pincer chelae and estimating the actual forces generated by the contraction of the muscles and the magnitude of the forces transmitted around the fulcrum to the tip…

13. Photocopy of c. 1906 photograph of Corliss steam engine ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Photocopy of c. 1906 photograph of Corliss steam engine that drove can crusher (maker unknown) that was located on second floor of mill building; the young boy on the left is J. Wilson Lepine. - Laurel Valley Sugar Plantation, Sugar Mill, 2 miles South of Thibodaux on State Route 308, Thibodaux, Lafourche Parish, LA

1. VIEW, LOOKING NORTHEAST, SHOWING THE SITE OF THE EMPIRE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW, LOOKING NORTHEAST, SHOWING THE SITE OF THE EMPIRE MILL. THE ADIT IS AT TOP, ABOVE THE TERRACES FOR THE CRUSHER AND 5-STAMP MILL. REMAINS OF THE BOILER HOUSING ARE ON THE LOWER TERRACE, AT RIGHT, WITH ENGINE MOUNT TO LEFT - Empire Mill, Southern Edge of Salt Spring Valley, Copperopolis, Calaveras County, CA

Design considerations for a roll crusher/splitter for woody biomass

Treesearch

Donald L. Sirois; Colin Ashmore

1986-01-01

The principal focus of biomass harvesting in the past has been the use of chipping systems to reduce a wide variety of woody materials down to small pieces for easier handling and transporting. However, chipping systems have several short comings that limit their operational environments. For example, a conventional chipping system might not be applicable for...

76 FR 40237 - Approval and Disapproval and Promulgation of Air Quality Implementation Plans; Montana; Revisions...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... before permit issuance. The rule only allows installing concrete foundations work, below ground plumbing...)), submitted on May 28, 2003; 17.8.743 (except the phrases ``asphalt concrete plants, mineral crushers'' in 17... following provisions in Subchapter 7: ARM 17.8.743(1)(c) and ARM 17.8.770, the phrase ``asphalt concrete...

7. VIEW OF BASEMENT, LOOKING NORTH ALONG EAST BASEMENT WALL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. VIEW OF BASEMENT, LOOKING NORTH ALONG EAST BASEMENT WALL TOWARD TURBINES. AT RIGHT IS A WATER-POWERED EAR CORN CRUSHER (manufacturer unknown), WHICH PERFORMED THE INITIAL COARSE GRINDING OF EAR CORN Photographer: Jet T. Lowe, 1985 - Alexander's Grist Mill, Lock 37 on Ohio & Erie Canal, South of Cleveland, Valley View, Cuyahoga County, OH

1. EAGLE MILL EXTERIOR FROM NORTHWEST, c. 1907. SHOWS INITIAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EAGLE MILL EXTERIOR FROM NORTHWEST, c. 1907. SHOWS INITIAL MILL CONFIGURATION WITH FULLY EXPOSED CRUDE ORE BIN CONCRETE RETAINING WALL, SINGLE (SOUTH) CRUDE ORE BIN, AND EXPOSED CRUSHER HOUSE. NOTE THE LACK OF MACHINE SHOP OR SNOW SHEDS. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Reduction of Biomass Moisture by Crushing/Splitting - A Concept

Treesearch

Paul E. Barnett; Donald L. Sirois; Colin Ashmore

1986-01-01

A biomass crusher/splitter concept is presented as a possible n&ant of tsafntainfng rights-of-way (ROW) or harvesting energy wood plantations. The conceptual system would cut, crush, and split small woody biomass leaving it in windrows for drying. A subsequent operation would bale and transport the dried material for use as an energy source. A survey of twenty...

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. DETAIL OF STRUCTURAL COLLAPSE OF TOP FLOOR OF MILL, ABOVE ORE BIN, LOOKING WEST FROM TOP OF STAIRWAY IN CA-290-25. THE PIPE AT CENTER WAS USED TO SPREAD CRUSHED ORE COMING FROM THE JAW CRUSHER EVENLY TO ALL AREA OF THE ORE BIN BELOW. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Reducing fire hazard in ponderosa pine thinning slash by mechanical crushing

Treesearch

John R. Dell; Franklin R. Ward

1969-01-01

Precommercial thinning in ponderosa pine stands in the Western United States is a growing practice. Thinning slash can, however, be a serious fire hazard in dry areas. Crushing and compacting this slash may be one way of reducing the hazard. Three types of mechanical crushers were tested on the Deschutes National Forest, Oregon. Results indicate that at least one of...

Evaluation of moisture reduction in small diameter trees after crushing

Treesearch

Donald L. Sirois; Cynthia L. Rawlins; Bryce J. Stokes

1991-01-01

Past studies have suggested that processing small diameter whole trees like those foumd on rights-of-way (ROWs) would help reduce transportion costs and increase energy value by lowering stem moisture content. Small stems were crushed by a roller crusher/splitter test bench machine and allowed dry under field conditions in Alabama. Tests were conducted in winter and...

Top 10 Products of 2011

ERIC Educational Resources Information Center

American School & University, 2011

2011-01-01

In 2011, American School & University (AS&U) showcased some of the hottest products in the industry. This article presents the top ten most requested products as determined by readers. The top one on the list is the Bulb crusher which can cut recycling costs by 50%, can hold 1,350 4-foot lamps in a single 55-gallon drum, can crush a 4-foot lamp in…

3. EAGLE MILL, DETAIL OF CRUDE ORE BIN FROM NORTH, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. EAGLE MILL, DETAIL OF CRUDE ORE BIN FROM NORTH, c. 1908-10. SHOWS EXPOSED CRUSHER HOUSE IN FRONT OF (SOUTH) CRUDE ORE BIN AND SNOW SHED ADDED OVER TRAM TRACKS. NOTE LACK OF EAST OR WEST CRUDE ORE BINS. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Friction and Wear Reduction of Eccentric Journal Bearing Made of Sn-Based Babbitt for Ore Cone Crusher

PubMed Central

Amanov, Auezhan; Ahn, Byungmin; Lee, Moon Gu; Jeon, Yongho; Pyun, Young-Sik

2016-01-01

An anti-friction Babbitt alloy-coated bearing made by a casting process is a journal bearing, which is used in an ore cone crusher eccentric. The main purpose of the Babbitt coated eccentric is to provide a low friction to support and guide a rotating shaft. Despite the fact that the Babbitt-coated eccentric offers a low friction coefficient and can be operated without a continuous supply of lubricant, it suffers from mining environments and short service life. In this study, an ultrasonic nanocrystalline surface modification (UNSM) technique was used to further reduce the friction coefficient, to increase the wear resistance, and to extend the service life of the Sn-based Babbitt metal. The friction and wear behavior of the Sn-based Babbitt metal was investigated using a block-on-ring tester under both dry and oil-lubricated conditions. The results of the experiments revealed that the friction and wear behavior of Sn-based Babbitt metal could be improved by the application of the UNSM technique. The friction and wear mechanisms of the specimens were explained and discussed in terms of changes in surface properties—microstructure, surface hardness, surface roughness, etc. PMID:28774070

Friction and Wear Reduction of Eccentric Journal Bearing Made of Sn-Based Babbitt for Ore Cone Crusher.

PubMed

Amanov, Auezhan; Ahn, Byungmin; Lee, Moon Gu; Jeon, Yongho; Pyun, Young-Sik

2016-11-22

An anti-friction Babbitt alloy-coated bearing made by a casting process is a journal bearing, which is used in an ore cone crusher eccentric. The main purpose of the Babbitt coated eccentric is to provide a low friction to support and guide a rotating shaft. Despite the fact that the Babbitt-coated eccentric offers a low friction coefficient and can be operated without a continuous supply of lubricant, it suffers from mining environments and short service life. In this study, an ultrasonic nanocrystalline surface modification (UNSM) technique was used to further reduce the friction coefficient, to increase the wear resistance, and to extend the service life of the Sn-based Babbitt metal. The friction and wear behavior of the Sn-based Babbitt metal was investigated using a block-on-ring tester under both dry and oil-lubricated conditions. The results of the experiments revealed that the friction and wear behavior of Sn-based Babbitt metal could be improved by the application of the UNSM technique. The friction and wear mechanisms of the specimens were explained and discussed in terms of changes in surface properties-microstructure, surface hardness, surface roughness, etc.

Simultaneous determination of docosahexaenoic acid and eicosapentaenoic acid in common seafood using ultrasonic cell crusher extraction combined with gas chromatography.

PubMed

Zhao, Juanjuan; Ren, Yan; Yu, Chen; Chen, Xiangming; Shi, Yanan

2017-02-01

An effective method for the simultaneous determination of docosahexaenoic acid and eicosapentaenoic acid in common seafood by gas chromatography was developed and validated. Total docosahexaenoic acid and eicosapentaenoic acid were extracted from seafood by ultrasonic cell crusher assisted extraction and methyl esterified for gas chromatography analysis in the presence of the internal standard. The linearity was good (r > 0.999) in 9.59 ∼ 479.5 μg/mL for docosahexaenoic acid and 9.56 ∼ 477.8 μg/mL for eicosapentaenoic acid. The intrarun and interrun precisions were both within 4.8 and 6.1% for the two analytes, while the accuracy was less than 5.8%. The developed method was applied for determination of docosahexaenoic acid and eicosapentaenoic acid in six kinds of seafood. The result showed the content of docosahexaenoic acid and eicosapentaenoic acid was all higher than 1 mg/g in yellow croaker, hairtail, venerupis philippinarum, mussel, and oyster. Our work may be helpful for dietary optimization and production of docosahexaenoic acid and eicosapentaenoic acid. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

Code of Federal Regulations, 2013 CFR

2013-07-01

... section. (1) All emission units within a group must be of the same process type (e.g., primary crushers... emission units from different process types together for the purposes of this section. (2) All emission units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...

40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

Code of Federal Regulations, 2014 CFR

2014-07-01

... section. (1) All emission units within a group must be of the same process type (e.g., primary crushers... emission units from different process types together for the purposes of this section. (2) All emission units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...

40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

Code of Federal Regulations, 2012 CFR

2012-07-01

... section. (1) All emission units within a group must be of the same process type (e.g., primary crushers... emission units from different process types together for the purposes of this section. (2) All emission units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...

40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... section. (1) All emission units within a group must be of the same process type (e.g., primary crushers... emission units from different process types together for the purposes of this section. (2) All emission units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...

40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... section. (1) All emission units within a group must be of the same process type (e.g., primary crushers... emission units from different process types together for the purposes of this section. (2) All emission units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...

20. Photocopy of photograph. Horgan, February 7, 1921. Negative #D ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. Photocopy of photograph. Horgan, February 7, 1921. Negative #D & H 21895 Original negative can be found in D & H collection of the Anthracite Heritage Museum, Scranton, Pennsylvania. INTERIOR VIEW OF BREAKER, TOP FLOORS, SHOWING DETAIL OF TOP SCREENS AND CRUSHERS AT TIME OF CONSTRUCTION - Marvine Colliery, Breaker No. 2, West side Boulevard Avenue, between East Parker Street & Route 380, Scranton, Lackawanna County, PA

Environmental Propagation of Noise in Mines and Nearby Villages: A Study Through Noise Mapping

PubMed Central

Manwar, Veena D.; Mandal, Bibhuti B.; Pal, Asim K.

2016-01-01

Background: Noise mapping being an established practice in Europe is hardly practiced for noise management in India although it is mandatory in Indian mines as per guidelines of the Directorate General of Mines Safety (DGMS). As a pilot study, noise mapping was conducted in an opencast mine with three different models; one based on the baseline operating conditions in two shifts (Situation A), and two other virtual situations where either production targets were enhanced by extending working hours to three shifts (Situation B) or only by increased mechanization and not changing the duration of work (Situation C). Methods: Noise sources were categorized as point, line, area, and moving sources. Considering measured power of the sources, specific meteorological and geographical parameters, noise maps were generated using Predictor LimA software. Results: In all three situations, Lden values were 95 dB(A) and 70–80 dB(A) near drill machine and haul roads, respectively. Noise contours were wider in Situation C due to increase in frequency of dumpers. Lden values near Shovel 1 and Shovel 2 under Situation B increased by 5 dB and 3 dB, respectively due to expansion of working hours. In Situation C, noise levels were >82 dB(A) around shovels. Noise levels on both sides of conveyor belts were in the range of 80–85 dB(A) in Situations A and C whereas it was 85–90 dB(A) in Situation B. Near crusher plants, it ranged from 80 to 90 dB(A) in Situations A and C and between 85 and 95 dB(A) in Situation B. In all situations, noise levels near residential areas exceeded the Central Pollution Control Board (CPCB) limits, i.e., 55 dB(A). Conclusions: For all situations, predicted noise levels exceeded CPCB limits within the mine and nearby residential area. Residential areas near the crusher plants are vulnerable to increased noise propagation. It is recommended to put an acoustic barrier near the crusher plant to attenuate the noise propagation. PMID:27569406

Environmental propagation of noise in mines and nearby villages: A study through noise mapping.

PubMed

Manwar, Veena D; Mandal, Bibhuti B; Pal, Asim K

2016-01-01

Noise mapping being an established practice in Europe is hardly practiced for noise management in India although it is mandatory in Indian mines as per guidelines of the Directorate General of Mines Safety (DGMS). As a pilot study, noise mapping was conducted in an opencast mine with three different models; one based on the baseline operating conditions in two shifts (Situation A), and two other virtual situations where either production targets were enhanced by extending working hours to three shifts (Situation B) or only by increased mechanization and not changing the duration of work (Situation C). Noise sources were categorized as point, line, area, and moving sources. Considering measured power of the sources, specific meteorological and geographical parameters, noise maps were generated using Predictor LimA software. In all three situations, Lden values were 95 dB(A) and 70-80 dB(A) near drill machine and haul roads, respectively. Noise contours were wider in Situation C due to increase in frequency of dumpers. Lden values near Shovel 1 and Shovel 2 under Situation B increased by 5 dB and 3 dB, respectively due to expansion of working hours. In Situation C, noise levels were >82 dB(A) around shovels. Noise levels on both sides of conveyor belts were in the range of 80-85 dB(A) in Situations A and C whereas it was 85-90 dB(A) in Situation B. Near crusher plants, it ranged from 80 to 90 dB(A) in Situations A and C and between 85 and 95 dB(A) in Situation B. In all situations, noise levels near residential areas exceeded the Central Pollution Control Board (CPCB) limits, i.e., 55 dB(A). For all situations, predicted noise levels exceeded CPCB limits within the mine and nearby residential area. Residential areas near the crusher plants are vulnerable to increased noise propagation. It is recommended to put an acoustic barrier near the crusher plant to attenuate the noise propagation.

EAST ELEVATION OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. TRAM CARS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EAST ELEVATION OF LOWER TRAM TERMINAL, LOOKING NORTHWEST. TRAM CARS ENTERED AND EXITED FROM RIGHT,AND DUMPED INTO THE ORE BIN SEEN AT LOWER LEFT. BELOW THE ORE BIN IS A JAW CRUSHER FOUNDATION. THE WOODEN BOX AT CENTER IS FILLED WITH ROCKS, PROVIDING THE COUNTERWEIGHT TO THE TRAMWAY CABLE, WHICH KEEPS IT TAUGHT. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

Check Firing of Master and Reference Propellants

DTIC Science & Technology

2014-12-08

estimate amount and color of smoke generated. s. Visually estimate amount and color of muzzle flash generated. TOP 04-2-607A 8 December 2014 10...Stargauge. TOP 04-2-607A 8 December 2014 3 e. Pressure gauge (piezoelectric preferred, and/or crusher). f. Muzzle velocity radar unit...firing: a. Provide electronics personnel with the weapon caliber and type, the weight and model of projectile, and expected muzzle velocities. b

A multi-particle crushing apparatus for studying rock fragmentation due to repeated impacts

NASA Astrophysics Data System (ADS)

Huang, S.; Mohanty, B.; Xia, K.

2017-12-01

Rock crushing is a common process in mining and related operations. Although a number of particle crushing tests have been proposed in the literature, most of them are concerned with single-particle crushing, i.e., a single rock sample is crushed in each test. Considering the realistic scenario in crushers where many fragments are involved, a laboratory crushing apparatus is developed in this study. This device consists of a Hopkinson pressure bar system and a piston-holder system. The Hopkinson pressure bar system is used to apply calibrated dynamic loads to the piston-holder system, and the piston-holder system is used to hold rock samples and to recover fragments for subsequent particle size analysis. The rock samples are subjected to three to seven impacts under three impact velocities (2.2, 3.8, and 5.0 m/s), with the feed size of the rock particle samples limited between 9.5 and 12.7 mm. Several key parameters are determined from this test, including particle size distribution parameters, impact velocity, loading pressure, and total work. The results show that the total work correlates well with resulting fragmentation size distribution, and the apparatus provides a useful tool for studying the mechanism of crushing, which further provides guidelines for the design of commercial crushers.

14. VIEW FROM TRACK AT NORTHEAST CORNER OF THE PLANT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. VIEW FROM TRACK AT NORTHEAST CORNER OF THE PLANT TOWARD A COAL TRESTLE EAST OF THE PLANT. THE TRESTLE WAS ADDED IN 1910. HOPPER CARS WERE WINCHED OVER A CRUSHER LOCATED DIRECTLY UNDER THE SHED AND DUMPED. A HEATED TRACK SECTION JUST BEYOND THE SHED WAS USED TO THAW FROZEN CARS IN COLD WEATHER. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Gear Drive Testing

NASA Technical Reports Server (NTRS)

1982-01-01

Philadelphia Gear Corporation used two COSMIC computer programs; one dealing with shrink fit analysis and the other with rotor dynamics problems in computerized design and test work. The programs were used to verify existing in-house programs to insure design accuracy by checking its company-developed computer methods against procedures developed by other organizations. Its specialty is in custom units for unique applications, such as Coast Guard ice breaking ships, steel mill drives, coal crusher, sewage treatment equipment and electricity.

SOUTH ELEVATION OF GOLD HILL MILL, LOOKING NORTH. THE PRIMARY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTH ELEVATION OF GOLD HILL MILL, LOOKING NORTH. THE PRIMARY ORE BIN IS A CENTER, WITH A JAW CRUSHER JUST TO THE RIGHT. A CONVEYOR (MISSING) WAS USED TO CARRY CRUSHED ORE UP AND INTO THE SECONDARY ORE BIN. THE STONE RAMP TO THE LEFT OF THE ORE BIN WAS USED TO DRIVE TRUCKS UP TO DUMPING LEVEL. - Gold Hill Mill, Warm Spring Canyon Road, Death Valley Junction, Inyo County, CA

41. INTERIOR VIEW LOOKING NORTH ON THE MAIN POWER SHAFT/CAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. INTERIOR VIEW LOOKING NORTH ON THE MAIN POWER SHAFT/CAM LEVEL LOOKING TOWARD THE STAMP BATTERIES. NOTE THE UN-HEWN LUMBER SPANNING THE LARGE TIMBER FRAME STRUCTURAL MEMBERS, IT IS BELIEVED THESE WERE ADDED LATER TO ADD ADDITIONAL STABILITY TO THE STAMP BATTERIES. ALSO NOTE THE ORE BINS AND ROCK CRUSHER BEHIND THE BATTERIES. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Preventive Maintenance and Reliability Study for the Central Heating and Power Plant at Fort Wainwright, Alaska

DTIC Science & Technology

2007-09-01

replacement of truck hopper, pan conveyor , belt conveyor , dust enclosures, magnetic separator, crusher and bypass, collec- tion chutes , bucket elevator, and...respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other...stopped. If such an event oc- curred in the winter, installation missions and personnel would be put at risk. The plant was redundantly designed

Preventative Maintenance and Reliability Study for the Central Heating and Power Plant at Fort Wainwright, Alaska

DTIC Science & Technology

2007-09-01

replacement of truck hopper, pan conveyor , belt conveyor , dust enclosures, magnetic separator, crusher and bypass, collec- tion chutes , bucket elevator, and...respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other...stopped. If such an event oc- curred in the winter, installation missions and personnel would be put at risk. The plant was redundantly designed

32. INTERIOR VIEW LOOKING NORTH ON THE ORE BREAKER LEVEL. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. INTERIOR VIEW LOOKING NORTH ON THE ORE BREAKER LEVEL. THE ORE BREAKER, A BLAKE JAW CRUSHER, IS IN THE BOX IN THE LEFT OF THE PHOTOGRAPH, THE ORE TO BE BROKEN IS FED INTO THE OPENING ON THE FLOOR AND NEXT TO ORE BREAKER BOX. THE GRIZZLY BARS ARE ON THE RIGHT AND THE PULLEYS FROM THE POWER SYSTEM ARE OVERHEAD. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

Environmental friendly crush-magnetic separation technology for recycling metal-plated plastics from end-of-life vehicles.

PubMed

Xue, Mianqiang; Li, Jia; Xu, Zhenming

2012-03-06

Metal-plated plastics (MPP), which are important from the standpoint of aesthetics or even performance, are increasingly employed in a wide variety of situations in the automotive industry. Serious environmental problems will be caused if they are not treated appropriately. Therefore, recycling of MPP is an important subject not only for resource recycling but also for environmental protection. This work represents a novel attempt to deal with the MPP. A self-designed hammer crusher was used to liberate coatings from the plastic substrate. The size distribution of particles was analyzed and described by the Rosin-Rammler function model. The optimum retaining time of materials in the crusher is 3 min. By this time, the liberation rate of the materials can reach 87.3%. When the density of the suspension is 31,250 g/m(3), the performance of liberation is the best. Two-step magnetic separation was adopted to avoid excessive crushing and to guarantee the quality of products. Concerning both the separation efficiency and grade of products, the optimum rotational speed of the magnetic separator is 50-70 rpm. On the basis of the above studies about the liberating and separating behavior of the materials, a continuous recycling system (the technology of crush-magnetic separation) is developed. This recycling system provides a feasible method for recycling MPP efficiently, economically, and environmentally.

Crushing leads to waste disposal savings for FUSRAP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Darby, J.

1997-02-01

In this article the author discusses the application of a rock crusher as a means of implementing cost savings in the remediation of FUSRAP sites. Transportation and offsite disposal costs are at present the biggest cost items in the remediation of FUSRAP sites. If these debris disposal problems can be handled in different manners, then remediation savings are available. Crushing can result in the ability to handle some wastes as soil disposal problems, which have different disposal regulations, thereby permitting cost savings.

Gas chromatographic analysis of volatiles in fluid and gas inclusions

USGS Publications Warehouse

Andrawes, F.; Holzer, G.; Roedder, E.; Gibson, E.K.; Oro, John

1984-01-01

Most geological samples and some synthetic materials contain fluid inclusions. These inclusions preserve for us tiny samples of the liquid and/or the gas phase that was present during formation, although in some cases they may have undergone significant changes from the original material. Studies of the current composition of the inclusions provide data on both the original composition and the change since trapping.These inclusions are seldom larger than 1 millimeter in diameter. The composition varies from a single major compound (e.g., water) in a single phase to a very complex mixture in one or more phases. The concentration of some of the compounds present may be at trace levels.We present here some analyses of inclusions in a variety of geological samples, including diamonds. We used a sample crusher and a gas chromatography—mass spectrometry (GC—MS) system to analyze for organic and inorganic volatiles present as major to trace constituents in inclusions. The crusher is a hardened stainless-steel piston cylinder apparatus with tungsten carbide crusing surfaces, and is operated in a pure helium atmosphere at a controlled temperature.Samples ranging from 1 mg to 1 g were crushed and the released volatiles were analyzed using multi-chromatographic columns and detectors, including the sensitive helium ionization detector. Identification of the GC peaks was carried out by GC—MS. This combination of procedures has been shown to provide geochemically useful information on the process involved in the history of the samples analyzed.

Gas chromatographic analysis of volatiles in fluid and gas inclusions.

PubMed

Andrawes, F; Holzer, G; Roedder, E; Gibson, E K; Oro, J

1984-01-01

Most geological samples and some synthetic materials contain fluid inclusions. These inclusions preserve for us tiny samples of the liquid and/or the gas phase that was present during formation, although in some cases they may have undergone significant changes from the original material. Studies of the current composition of the inclusions provide data on both the original composition and the change since trapping. These conclusions are seldom larger than 1 millimeter in diameter. The composition varies from a single major compound (e.g., water) in a single phase to a very complex mixture in one or more phases. The concentration of some of the compounds present may be at trace levels. We present here some analyses of inclusion on a variety of geological samples, including diamonds. We used a sample crusher and a gas chromatography-mass spectrometry (GC-MS) system to analyze for organic and inorganic volatiles present as major to trace constituents in inclusions. The crusher is a hardened stainless-steel piston cylinder apparatus with tungsten carbide crushing surfaces, and is operated in a pure helium atmosphere at a controlled temperature. Samples ranging from 1 mg to 1 g were crushed and the released volatiles were analyzed using multi-chromatographic columns and detectors, including the sensitive helium ionization detector. Identification of the GC peaks was carried out by GC-MS. This combination of procedures has been shown to provide geochemically useful information on the processes involved in the history of the samples analyzed.

EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH PRIMARY AND SECONDARY LIMESTONE REDUCTION ('CRUSHING') IN PROGRESS. FEEDER (RIGHT) FEEDS TO CONVEYOR BELTS (CENTER) AND CRUSHER (LEFT). LIMESTONE PROCESSED THROUGH THIS OPERATION IS FURTHER SCREENED AND PROCESSED AT ANOTHER PLANT ON THE THOMAS SITE. OPERATION OF THIS PLANT, WHICH BEGAN IN 1960, INCORPORATES WITHIN THE FEEDER A CONCRETE RETAINING WALL DATING TO A TURN OF THE CENTURY QUARRY OPERATION FORMERLY ON THIS SITE. - Wade Sand & Gravel Company, Reduction Plant No. 6, State Route 78, Thomas, Jefferson County, AL

4. TROJAN MILL, DETAIL OF CRUDE ORE BINS FROM NORTH, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. TROJAN MILL, DETAIL OF CRUDE ORE BINS FROM NORTH, c. 1912. SHOWS TIMBER FRAMING UNDER CONSTRUCTION FOR EAST AND WEST CRUDE ORE BINS AT PREVIOUS LOCATION OF CRUSHER HOUSE, AND SNOW SHED PRESENT OVER SOUTH CRUDE ORE BIN WITH PHASE CHANGE IN SNOW SHED CONSTRUCTION INDICATED AT EAST END OF EAST CRUDE ORE BIN. THIS PHOTOGRAPH IS THE FIRST IMAGE OF THE MACHINE SHOP, UPPER LEFT CORNER. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

On a Molecular Basis, Investigate Association of Molecular Structure with Bioactive Compounds, Anti-Nutritional Factors and Chemical and Nutrient Profiles of Canola Seeds and Co-Products from Canola Processing: Comparison Crusher Plants within Canada and within China as well as between Canada and China.

PubMed

Gomaa, Walaa M S; Mosaad, Gamal M; Yu, Peiqiang

2018-04-21

The objectives of this study were to: (1) Use molecular spectroscopy as a novel technique to quantify protein molecular structures in relation to its chemical profiles and bioenergy values in oil-seeds and co-products from bio-oil processing. (2) Determine and compare: (a) protein molecular structure using Fourier transform infrared (FT/IR-ATR) molecular spectroscopy technique; (b) bioactive compounds, anti-nutritional factors, and chemical composition; and (c) bioenergy values in oil seeds (canola seeds), co-products (meal or pellets) from bio-oil processing plants in Canada in comparison with China. (3) Determine the relationship between protein molecular structural features and nutrient profiles in oil-seeds and co-products from bio-oil processing. Our results showed the possibility to characterize protein molecular structure using FT/IR molecular spectroscopy. Processing induced changes between oil seeds and co-products were found in the chemical, bioenergy profiles and protein molecular structure. However, no strong correlation was found between the chemical and nutrient profiles of oil seeds (canola seeds) and their protein molecular structure. On the other hand, co-products were strongly correlated with protein molecular structure in the chemical profile and bioenergy values. Generally, comparisons of oil seeds (canola seeds) and co-products (meal or pellets) in Canada, in China, and between Canada and China indicated the presence of variations among different crusher plants and bio-oil processing products.

Silica dust exposure: Effect of filter size to compliance determination

NASA Astrophysics Data System (ADS)

Amran, Suhaily; Latif, Mohd Talib; Khan, Md Firoz; Leman, Abdul Mutalib; Goh, Eric; Jaafar, Shoffian Amin

2016-11-01

Monitoring of respirable dust was performed using a set of integrated sampling system consisting of sampling pump attached with filter media and separating device such as cyclone or special cassette. Based on selected method, filter sizes are either 25 mm or 37 mm poly vinyl chloride (PVC) filter. The aim of this study was to compare performance of two types of filter during personal respirable dust sampling for silica dust under field condition. The comparison strategy focused on the final compliance judgment based on both dataset. Eight hour parallel sampling of personal respirable dust exposure was performed among 30 crusher operators at six quarries. Each crusher operator was attached with parallel set of integrated sampling train containing either 25 mm or 37 mm PVC filter. Each set consisted of standard flow SKC sampler, attached with SKC GS3 cyclone and 2 pieces cassette loaded with 5.0 µm of PVC filter. Samples were analyzed by gravimetric technique. Personal respirable dust exposure between the two types of filters indicated significant positive correlation (p < 0.05) with moderate relationship (r2 = 0.6431). Personal exposure based on 25 mm PVC filter indicated 0.1% non-compliance to overall data while 37 mm PVC filter indicated similar findings at 0.4 %. Both data showed similar arithmetic mean(AM) and geometric mean(GM). In overall we concluded that personal respirable dust exposure either based on 25mm or 37mm PVC filter will give similar compliance determination. Both filters are reliable to be used in respirable dust monitoring for silica dust related exposure.

The influence of flushing time on the bonding quality of liquid white cast iron on the solid surface of similar material

NASA Astrophysics Data System (ADS)

Bandanadjaja, Beny; Purwadi, Wiwik; Idamayanti, Dewi; Lilansa, Noval; Hanaldi, Kus; Nurzaenal, Friya Kurnia

2018-05-01

Hard metal castings are widely used in the coal mill pulverizer as construction material for coal crushers. During its operation crushers and mills experience degradation caused by abrasion load. This research dealed with the surface overlaying of similiar material on the surface of white cast iron by mean of gravity casting. The die blank casting was preheated prior to the casting process of outer layer made of Ni-Hard white cast iron to guarantee bonding processes and avoid any crack. The preheating temperature of die blankin ther range of 500C up to 850C was set up to reach the interface temperature in the range of 887°C -1198°C and the flushing time was varied between 10-20 seconds. Studies carried on the microstructure of sample material revealed a formation of metallurgical bonding at the preheating temperature above 625 °C by pouring temperature ranging from 1438 °C to 1468 °C. Metallographical and chemical composition by mean of EDS examination were performed to observed the resut. This research concludes that the casting of Ni-Hard 1 overlay by applying gravity casting method can be done by preheating the surface of casting to 625 °C, interface temperature of 1150 °C, flushing time of 7 seconds and pouring temperature of 1430 °C. Excellent metallurgical bonding at the contact area between dieblank and overlay material has been achieved in which there is no parting line at the interface area to be observed.

Vibration induced white-feet: overview and field study of vibration exposure and reported symptoms in workers.

PubMed

Eger, Tammy; Thompson, Aaron; Leduc, Mallorie; Krajnak, Kristine; Goggins, Katie; Godwin, Alison; House, Ron

2014-01-01

Workers who stand on platforms or equipment that vibrate are exposed to foot-transmitted vibration (FTV). Exposure to FTV can lead to vibration white feet/toes resulting in blanching of the toes, and tingling and numbness in the feet and toes. The objectives are 1) to review the current state of knowledge of the health risks associated with foot-transmitted vibration (FTV), and 2) to identify the characteristics of FTV and discuss the associated risk of vibration-induced injury. Workers who operated locomotives (n=3), bolting platforms (n=10), jumbo drills (n=7), raise drilling platforms (n=4), and crushers (n=3), participated. A tri-axial accelerometer was used to measure FTV in accordance with ISO 2631-1 guidelines. Frequency-weighted root-mean-square acceleration and the dominant frequency are reported. Participants were also asked to report pain/ache/discomfort in the hands and/or feet. Reports of pain/discomfort/ache were highest in raise platform workers and jumbo drill operators who were exposed to FTV in the 40 Hz and 28 Hz range respectively. Reports of discomfort/ache/pain were lowest in the locomotive and crusher operators who were exposed to FTV below 10 Hz. These findings are consistent with animal studies that have shown vascular and neural damage in exposed appendages occurs at frequencies above 40 Hz. Operators exposed to FTV at 40 Hz appear to be at greater risk of experiencing vibration induced injury. Future research is required to document the characteristics of FTV and epidemiological evidence is required to link exposure with injury.

Crusher Inspector (Iron and Steel) 631.381; Mill-End Inspector (Iron and Steel) 619.381; Mill Inspector (Iron and Steel) 619.381; Pipe and Coupling Sizer (Iron and Steel) 619.381; Pipe Walker (Iron and Steel) 619.381; Thread Inspector (Iron and Steel) 619.687 -- Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

How crawler track-mounted conveyors improve bulk handling's economics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hawkins, G.P.

1984-11-01

Crawler track-mounted conveyors can be used in most applications formerly requiring stacking, reclaiming or movement from excavators to bench conveyors. The crawler track-mounted conveyor has been automated for push button operation and allows mobilization of in-pit operations for the movement of overburden, minerals and coal. In-pit mobilization of crushers, the use of mobilized steep angle conveyor for the removal of coal from the pit, and the movement of overburden from excavation to spoil can all be done more economically when a combination of a crawler track mounted conveyor is used in conjunction with a shiftable or fixed conveyor.

Strength Characteristics of Quarry Dust in Replacement of Sand

NASA Astrophysics Data System (ADS)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

Vibration induced white-feet: Overview and field study of vibration exposure and reported symptoms in workers

PubMed Central

Eger, Tammy; Thompson, Aaron; Leduc, Mallorie; Krajnak, Kristine; Goggins, Katie; Godwin, Alison; House, Ron

2015-01-01

BACKGROUND Workers who stand on platforms or equipment that vibrate are exposed to foot-transmitted vibration (FTV). Exposure to FTV can lead to vibration white feet/toes resulting in blanching of the toes, and tingling and numbness in the feet and toes. OBJECTIVES The objectives are 1) to review the current state of knowledge of the health risks associated with foot-transmitted vibration (FTV), and 2) to identify the characteristics of FTV and discuss the associated risk of vibration-induced injury. PARTICIPANTS Workers who operated locomotives (n = 3), bolting platforms (n = 10), jumbo drills (n = 7), raise drilling platforms (n = 4), and crushers (n = 3), participated. METHODS A tri-axial accelerometer was used to measure FTV in accordance with ISO 2631-1 guidelines. Frequency-weighted root-mean-square acceleration and the dominant frequency are reported. Participants were also asked to report pain/ache/discomfort in the hands and/or feet. RESULTS Reports of pain/discomfort/ache were highest in raise platform workers and jumbo drill operators who were exposed to FTV in the 40 Hz and 28 Hz range respectively. Reports of discomfort/ache/pain were lowest in the locomotive and crusher operators who were exposed to FTV below 10 Hz. These findings are consistent with animal studies that have shown vascular and neural damage in exposed appendages occurs at frequencies above 40 Hz. CONCLUSIONS Operators exposed to FTV at 40 Hz appear to be at greater risk of experiencing vibration induced injury. Future research is required to document the characteristics of FTV and epidemiological evidence is required to link exposure with injury. PMID:24004754

Westinghouse modular grinding process - improvement for follow on processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fehrmann, Henning

2013-07-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. The resins can be in bead or powdered form. For waste treatment of spent IX resins, two methods are basically used: Direct immobilization (e.g. with cement, bitumen, polymer or High Integrity Container (HIC)); Thermal treatment (e.g. drying, oxidation or pyrolysis). Bead resins have some properties (e.g. particle size and density) that can have negative impacts on following waste treatment processes. Negative impacts could be: Floatation of bead resins in cementation process; Sedimentation in pipeline during transportation; Poor compaction properties for Hot Resin Supercompactionmore » (HRSC). Reducing the particle size of the bead resins can have beneficial effects enhancing further treatment processes and overcoming prior mentioned effects. Westinghouse Electric Company has developed a modular grinding process to crush/grind the bead resins. This modular process is designed for flexible use and enables a selective adjustment of particle size to tailor the grinding system to the customer needs. The system can be equipped with a crusher integrated in the process tank and if necessary a colloid mill. The crusher reduces the bead resins particle size and converts the bead resins to a pump able suspension with lower sedimentation properties. With the colloid mill the resins can be ground to a powder. Compared to existing grinding systems this equipment is designed to minimize radiation exposure of the worker during operation and maintenance. Using the crushed and/or ground bead resins has several beneficial effects like facilitating cementation process and recipe development, enhancing oxidation of resins, improving the Hot Resin Supercompaction volume reduction performance. (authors)« less

Total number of longwall faces drops below 50

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2009-02-15

For the first time since Coal Age began its annual Longwall Census the number of faces has dropped below 50. A total of five mines operate two longwall faces. CONSOL Energy remains the leader with 12 faces. Arch Coal operates five longwall mines; Robert E. Murray owns five longwall mines. West Virginia has 13 longwalls, followed by Pennsylvania (8), Utah (6) and Alabama (6). A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries, depth of cut, model of equipment used (shearer, haulage system, roof support, facemore » conveyor, stage loader, crusher, electrical controls and voltage to face). 2 tabs., 1 photo.« less

High performance MRI simulations of motion on multi-GPU systems.

PubMed

Xanthis, Christos G; Venetis, Ioannis E; Aletras, Anthony H

2014-07-04

MRI physics simulators have been developed in the past for optimizing imaging protocols and for training purposes. However, these simulators have only addressed motion within a limited scope. The purpose of this study was the incorporation of realistic motion, such as cardiac motion, respiratory motion and flow, within MRI simulations in a high performance multi-GPU environment. Three different motion models were introduced in the Magnetic Resonance Imaging SIMULator (MRISIMUL) of this study: cardiac motion, respiratory motion and flow. Simulation of a simple Gradient Echo pulse sequence and a CINE pulse sequence on the corresponding anatomical model was performed. Myocardial tagging was also investigated. In pulse sequence design, software crushers were introduced to accommodate the long execution times in order to avoid spurious echoes formation. The displacement of the anatomical model isochromats was calculated within the Graphics Processing Unit (GPU) kernel for every timestep of the pulse sequence. Experiments that would allow simulation of custom anatomical and motion models were also performed. Last, simulations of motion with MRISIMUL on single-node and multi-node multi-GPU systems were examined. Gradient Echo and CINE images of the three motion models were produced and motion-related artifacts were demonstrated. The temporal evolution of the contractility of the heart was presented through the application of myocardial tagging. Better simulation performance and image quality were presented through the introduction of software crushers without the need to further increase the computational load and GPU resources. Last, MRISIMUL demonstrated an almost linear scalable performance with the increasing number of available GPU cards, in both single-node and multi-node multi-GPU computer systems. MRISIMUL is the first MR physics simulator to have implemented motion with a 3D large computational load on a single computer multi-GPU configuration. The incorporation of realistic motion models, such as cardiac motion, respiratory motion and flow may benefit the design and optimization of existing or new MR pulse sequences, protocols and algorithms, which examine motion related MR applications.

USA's Black Thunder mine: a truck and shovel operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorling, I.

During 1966/1967, ARCO obtained over 2,631 hectares (6,500 acres) of federal and state coal leases, and initial exploration was started. A total of 312 coal core holes were drilled and logged to determine the reserves and quality of the coal. The results indicated that a large surface mine could be developed to exploit the substantial reserves. The application procedure for permits was started early in 1974. Thunder Basin Coal Company is mining the Wyodak-Anderson Seam where the coal is about 21 meters (69 feet) thick. It has been estimated that a total of 750,000,000 tons of coal exist with amore » 0.3 to 0.4 percent sulfur content and a heating value of about 8,600 Btu per pound. The seam is mined in one lift using electric shovels and trucks. There are many factors which govern the choice of either a dragline or a truck and shovel operation for removing overburden. At the Black Thunder mine the conditions which favored the choice of the truck and shovel method were topography and pit geometry. The run-of-mine coal is dumped into two 540-ton hoppers. Underground vibrating grizzly feeders (2,500 tph capacity) pass the coal into 2,500 tph primary single-roll crushers, where the ROM coal is reduced to minus 8 inches. A 72-inch-wide elevating conveyor carries the coal to a 110-ton surge hopper, and is then fed into two secondary crushers where the coal is further reduced to minus-2 inches. The system is able to handle 5,000 tons of ROM coal per hour. The total production of coal from the mine in 1978 is expected to be about 3,000,000 tons, depending on customer requirements. It is expected that in 1979 the output will rise to 8,000,000 tons, and by 1983 the full planned production of 20,000,000 tons a year will be reached. (LTN)« less

Coal companies invest in more longwall capacity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2006-02-15

This year's annual survey shows not much has changed since last year. The overall population stands at 47 mines operating 53 longwalls. CONSOL Energy remains the leading US longwall operator with 13 installations, followed by Arch Coal (5), Robert E. Murray (5) and Massey Energy (4). West Virginia remains the leading longwall mining state with 14 faces in 2005, followed by Pennsylvania (8), Alabama (7), Utah (7) and Colorado (5). A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries, depth of cut, model of equipment usedmore » (shearer, haulage system, roof support, face conveyor, stage loader, crusher, electrical controls and voltage to face). 1 photos., 2 tabs.« less

Gasification in pulverized coal flames. First quarterly progress report, July--September 1975

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laurendeau, N. M.

1975-10-01

This project is concerned with the production of power and synthesis gases from pulverized coal via suspension gasification. Specifically, the concentric jet and vortex gasifiers, with separation of oxidation and reduction zones, will be investigated. Gasifier performance will be correlated with internally measured temperature and concentration profiles. A suction pyrometer will be used to simultaneously measure temperature and gas concentrations. Rapid species analysis will be provided by a UTI Q-30C mass spectrometer system. To date, a coal-handling facility has been developed, test cell design has been initiated, and preliminary literature searches have been made. A coal crusher, pulverizer, feeder, andmore » sieve shaker are on order. Preliminary consultations are underway concerning the mass spectrometer system. (auth)« less

PRB mines mature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchsbaum, L.

2007-08-15

Already seeing the results of reclamation efforts, America's largest surface mines advance as engineers prepare for the future. 30 years after the signing of the Surface Mining Control and Reclamation Act by Jimmy Carter, western strip mines in the USA, especially in the Powder River Basin, are producing more coal than ever. The article describes the construction and installation of a $38.5 million near-pit crusher and overland belt conveyor system at Foundation Coal West's (FCW) Belle Ayr surface mine in Wyoming, one of the earliest PRB mines. It goes on to describe the development by Rio Tinto of an elkmore » conservatory, the Rochelle Hill Conservation Easement, on reclaimed land at Jacobs Ranch, adjacent to the Rochelle Hills. 4 photos.« less

Underground coal operators install several new longwall mining systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2008-02-15

Several new names appear in the annual US Longwall Census, but the population remains the same: 52 although the number of longwall mines dropped from 40 to 47. CONSOL Energy remains the leader with 12 faces. Robert E. Murray owns 8 longwall mines followed by Arch Coal with 5 and Foundation Coal with 3. West Virginia has 13 longwalls followed by 9 in Pennsylvania, 7 in Utah and 6 in Alabama. The article describes CONSOL Energy's operations. A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries,more » depth of cut, model of equipment used (shearer, haulage system, roof support, face conveyor, stage loader, crusher, electrical controls and voltage to face). 2 tabs.« less

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES. THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH THE MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-42 (CT) FOR IDENTICAL COLOR TRANSPARENCY - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. EAST ELEVATION OF SKIDOO MILL, LOOKING WEST. THE LEVELS OF THE MILL CAN BE CLEARLY SEEN HERE. THE UPPER MOST LEVEL CONSISTS OF A CONVEORY THAT BROUGHT ORE TO A JAW CRUSHER. THE CRUSHED ORE WAS CHANNELED DIRECTLY INTO A LARGE ORE BIN LOCATED BEHIND THE COVERED WALL (CENTER). THE NEXT LEVEL SHOWS THE BULL (DRIVE) WHEEL ON THE UPPER PART OF THE STAMP BATTERIES THE NEXT LEVEL DOWN (STAIRS) IS THE LOWER PORTION OF THE STAMP BATTERIES WITH MORTAR BLOCKS AND APRONS. THE NEXT LEVEL DOWN (LOWER RIGHT) HELD CONCENTRATION (SHAKING) TABLES AND A CLASSIFIER. MOST EXTERIOR WALL COVERING, TIMBERS, AND ROOF IS MISSING FROM THE MILL. SEE CA-290-9 FOR IDENTICAL B&W NEGATIVE. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

High performance MRI simulations of motion on multi-GPU systems

PubMed Central

2014-01-01

Background MRI physics simulators have been developed in the past for optimizing imaging protocols and for training purposes. However, these simulators have only addressed motion within a limited scope. The purpose of this study was the incorporation of realistic motion, such as cardiac motion, respiratory motion and flow, within MRI simulations in a high performance multi-GPU environment. Methods Three different motion models were introduced in the Magnetic Resonance Imaging SIMULator (MRISIMUL) of this study: cardiac motion, respiratory motion and flow. Simulation of a simple Gradient Echo pulse sequence and a CINE pulse sequence on the corresponding anatomical model was performed. Myocardial tagging was also investigated. In pulse sequence design, software crushers were introduced to accommodate the long execution times in order to avoid spurious echoes formation. The displacement of the anatomical model isochromats was calculated within the Graphics Processing Unit (GPU) kernel for every timestep of the pulse sequence. Experiments that would allow simulation of custom anatomical and motion models were also performed. Last, simulations of motion with MRISIMUL on single-node and multi-node multi-GPU systems were examined. Results Gradient Echo and CINE images of the three motion models were produced and motion-related artifacts were demonstrated. The temporal evolution of the contractility of the heart was presented through the application of myocardial tagging. Better simulation performance and image quality were presented through the introduction of software crushers without the need to further increase the computational load and GPU resources. Last, MRISIMUL demonstrated an almost linear scalable performance with the increasing number of available GPU cards, in both single-node and multi-node multi-GPU computer systems. Conclusions MRISIMUL is the first MR physics simulator to have implemented motion with a 3D large computational load on a single computer multi-GPU configuration. The incorporation of realistic motion models, such as cardiac motion, respiratory motion and flow may benefit the design and optimization of existing or new MR pulse sequences, protocols and algorithms, which examine motion related MR applications. PMID:24996972

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

NASA Technical Reports Server (NTRS)

Breneman, W. C.; Cheung, H.; Farrier, E. G.; Morihara, H.

1977-01-01

A quartz fluid bed reactor capable of operating at temperatures of up to 1000 C was designed, constructed, and successfully operated. During a 30 minute experiment, silane was decomposed within the reactor with no pyrolysis occurring on the reactor wall or on the gas injection system. A hammer mill/roller-crusher system appeared to be the most practical method for producing seed material from bulk silicon. No measurable impurities were detected in the silicon powder produced by the free space reactor, using the cathode layer emission spectroscopic technique. Impurity concentration followed by emission spectroscopic examination of the residue indicated a total impurity level of 2 micrograms/gram. A pellet cast from this powder had an electrical resistivity of 35 to 45 ohm-cm and P-type conductivity.

KSC00pp0325

NASA Image and Video Library

2000-03-10

The Orange Crusher team (282) works on their robot, which is named Rust Bot, during the FIRST competition. The team of students from Lake Howell, Winter Springs and Orange Christian Private high schools was co-sponsored by NASA Kennedy Space Center, Matern Professional Engineering The Foundation, Control Technologies, Lucent Technologies and Sandy Engineering. Students from all over the country are at the KSC Visitor Complex for the FIRST (For Inspiration and Recognition of Science and Technology) Southeast Regional competition March 9-11 in the Rocket Garden. Teams of high school students are testing the limits of their imagination using robots they have designed, with the support of business and engineering professionals and corporate sponsors, to compete in a technological battle against other schools' robots. Of the 30 high school teams competing, 16 are Florida teams co-sponsored by NASA and KSC contractors. Local high schools participating are Astronaut, Bayside, Cocoa Beach, Eau Gallie, Melbourne, Melbourne Central Catholic, Palm Bay, Rockledge, Satellite, and Titusvill

KSC-00pp0325

NASA Image and Video Library

2000-03-10

The Orange Crusher team (282) works on their robot, which is named Rust Bot, during the FIRST competition. The team of students from Lake Howell, Winter Springs and Orange Christian Private high schools was co-sponsored by NASA Kennedy Space Center, Matern Professional Engineering The Foundation, Control Technologies, Lucent Technologies and Sandy Engineering. Students from all over the country are at the KSC Visitor Complex for the FIRST (For Inspiration and Recognition of Science and Technology) Southeast Regional competition March 9-11 in the Rocket Garden. Teams of high school students are testing the limits of their imagination using robots they have designed, with the support of business and engineering professionals and corporate sponsors, to compete in a technological battle against other schools' robots. Of the 30 high school teams competing, 16 are Florida teams co-sponsored by NASA and KSC contractors. Local high schools participating are Astronaut, Bayside, Cocoa Beach, Eau Gallie, Melbourne, Melbourne Central Catholic, Palm Bay, Rockledge, Satellite, and Titusvill

Complete endoscopic management of a retained bullet in the bladder.

PubMed

Friedman, Ariella A; Trinh, Quoc-Dien; Kaul, Sanjeev; Bhandari, Akshay

2013-01-01

A 25-year-old male gunshot victim presented at our institution with gross hematuria following Foley catheter insertion. Computed tomography and cystogram did not show a bladder perforation, but were notable for a left ischial fracture and the presence of a bullet within the bladder. After failed attempts at retrieving the bullet with a resectoscope and loop, as well as a cystoscope and stone crusher, a 26 French nephroscope was inserted transurethrally, and the bullet was successfully engaged and removed using a Perc NCircle (Cook Medical, Bloomington, IN) grasper. The extra-peritoneal injury was managed conservatively with catheter drainage. To our knowledge, this represents the first case of successful transurethral management of a retained intravesical bullet. Such an approach may benefit patients with retained intravesical bullets or other challenging intravesical foreign bodies and may be helpful in select circumstances to spare patients from more extensive surgeries.

Carbonation and CO{sub 2} uptake of concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Keun-Hyeok, E-mail: yangkh@kgu.ac.kr; Seo, Eun-A, E-mail: ssooaa@naver.com; Tae, Sung-Ho, E-mail: jnb55@hanyang.ac.kr

This study developed a reliable procedure to assess the carbon dioxide (CO{sub 2}) uptake of concrete by carbonation during the service life of a structure and by the recycling of concrete after demolition. To generalize the amount of absorbable CO{sub 2} per unit volume of concrete, the molar concentration of carbonatable constituents in hardened cement paste was simplified as a function of the unit content of cement, and the degree of hydration of the cement paste was formulated as a function of the water-to-cement ratio. The contribution of the relative humidity, type of finishing material for the concrete surface, andmore » the substitution level of supplementary cementitious materials to the CO{sub 2} diffusion coefficient in concrete was reflected using various correction factors. The following parameters varying with the recycling scenario were also considered: the carbonatable surface area of concrete crusher-runs and underground phenomena of the decreased CO{sub 2} diffusion coefficient and increased CO{sub 2} concentration. Based on the developed procedure, a case study was conducted for an apartment building with a principal wall system and an office building with a Rahmen system, with the aim of examining the CO{sub 2} uptake of each structural element under different exposure environments during the service life and recycling of the building. As input data necessary for the case study, data collected from actual surveys conducted in 2012 in South Korea were used, which included data on the surrounding environments, lifecycle inventory database, life expectancy of structures, and recycling activity scenario. Ultimately, the CO{sub 2} uptake of concrete during a 100-year lifecycle (life expectancy of 40 years and recycling span of 60 years) was estimated to be 15.5%–17% of the CO{sub 2} emissions from concrete production, which roughly corresponds to 18%–21% of the CO{sub 2} emissions from the production of ordinary Portland cement. - Highlights: • CO{sub 2} uptake assessment approach owing to the concrete carbonation is developed. • An equation to directly determine the absorbable CO{sub 2} amount in concrete is proposed. • The carbonatable surface area of concrete crusher-runs for CO{sub 2} uptake is ascertained. • This study provides typical data for uptake and emission of CO{sub 2} in concrete building.« less

Gasification in pulverized coal flames. First annual progress report, July 1975--June 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lenzer, R. C.; George, P. E.; Thomas, J. F.

1976-07-01

This project concerns the production of power and synthesis gas from pulverized coal via suspension gasification. Swirling flow in both concentric jet and cyclone gasifiers will separate oxidation and reduction zones. Gasifier performance will be correlated with internally measured temperature and concentration profiles. A literature review of vortex and cyclone reactors is complete. Preliminary reviews of confined jet reactors and pulverized coal reaction models have also been completed. A simple equilibrium model for power gas production is in agreement with literature correlations. Cold gas efficiency is not a suitable performance parameter for combined cycle operation. The coal handling facility, equippedmore » with crusher, pulverizer and sieve shaker, is in working order. Test cell flow and electrical systems have been designed, and most of the equipment has been received. Construction of the cyclone gasifier has begun. A preliminary design for the gas sampling system, which will utilize a UTI Q-30C mass spectrometer, has been developed.« less

Team 282 prepares for the FIRST competition

NASA Technical Reports Server (NTRS)

2000-01-01

The Orange Crusher team (282) works on their robot, which is named Rust Bot, during the FIRST competition. The team of students from Lake Howell, Winter Springs and Orange Christian Private high schools was co-sponsored by NASA Kennedy Space Center, Matern Professional Engineering The Foundation, Control Technologies, Lucent Technologies and Sandy Engineering. Students from all over the country are at the KSC Visitor Complex for the FIRST (For Inspiration and Recognition of Science and Technology) Southeast Regional competition March 9-11 in the Rocket Garden. Teams of high school students are testing the limits of their imagination using robots they have designed, with the support of business and engineering professionals and corporate sponsors, to compete in a technological battle against other schools' robots. Of the 30 high school teams competing, 16 are Florida teams co- sponsored by NASA and KSC contractors. Local high schools participating are Astronaut, Bayside, Cocoa Beach, Eau Gallie, Melbourne, Melbourne Central Catholic, Palm Bay, Rockledge, Satellite, and Titusville.

Optimizing the use of natural gravel Brantas river as normal concrete mixed with quality fc = 19.3 Mpa

NASA Astrophysics Data System (ADS)

Limantara, A. D.; Widodo, A.; Winarto, S.; Krisnawati, L. D.; Mudjanarko, S. W.

2018-04-01

The use of natural gravel (rivers) as concrete mixtures is rarely encountered after days of demands for a higher strength of concrete. Moreover, today people have found High-Performance Concrete which, when viewed from the rough aggregate consisted mostly of broken stone, although the fine grain material still used natural sand. Is it possible that a mixture of concrete using natural gravel as a coarse aggregate is capable of producing concrete with compressive strength equivalent to a concrete mixture using crushed stone? To obtain information on this, a series of tests on concrete mixes with crude aggregates of Kalitelu Crusher, Gondang, Tulungagung and natural stone (river gravel) from the Brantas River, Ngujang, Tulungagung in the Materials Testing Laboratory Tugu Dam Construction Project, Kab. Trenggalek. From concrete strength test results using coarse material obtained value 19.47 Mpa, while the compressive strength of concrete with a mixture of crushed stone obtained the value of 21.12 Mpa.

Exposure to Fibres, Crystalline Silica, Silicon Carbide and Sulphur Dioxide in the Norwegian Silicon Carbide Industry

PubMed Central

Føreland, S.; Bye, E.; Bakke, B.; Eduard, W.

2008-01-01

Objectives: The aim of this study was to assess personal exposure to fibres, crystalline silica, silicon carbide (SiC) and sulphur dioxide in the Norwegian SiC industry. Methods: Approximately 720 fibre samples, 720 respirable dust samples and 1400 total dust samples were collected from randomly chosen workers from the furnace, processing and maintenance departments in all three Norwegian SiC plants. The respirable dust samples were analysed for quartz, cristobalite and non-fibrous SiC content. Approximately 240 sulphur dioxide samples were collected from workers in the furnace department. Results: The sorting operators from all plants, control room and cleaning operators in Plant A and charger, charger/mix and payloader operators in Plant C had a geometric mean (GM) of fibre exposure above the Norwegian occupational exposure limit (OEL) (0.1 fibre cm−3). The cleaner operators in Plant A had the highest GM exposure to respirable quartz (20 μg m−3). The charger/mix operators in Plant C had the highest GM exposure to respirable cristobalite (38 μg m−3) and the refinery crusher operators in Plant A had the highest GM exposure to non-fibrous SiC (0.65 mg m−3). Exposure to the crystalline silica and non-fibrous SiC was generally low and between 0.4 and 2.1% of the measurements exceeded the OELs. The cleaner operators in Plant A had the highest GM exposure to respirable dust (1.3 mg m−3) and total dust (21 mg m−3). GM exposures for respirable dust above the Norwegian SiC industry-specific OEL of 0.5 mg m−3 were also found for refinery crusher operators in all plants and mix, charger, charger/mix and sorting operators in Plant C. Only 4% of the total dust measurements exceeded the OEL for nuisance dust of (10 mg m−3). Exposure to sulphur dioxide was generally low. However, peaks in the range of 10–100 p.p.m. were observed for control room and crane operators in Plants A and B and for charger and charger/mix operators in Plant C. Conclusion: Workers in the SiC industry are exposed to a mixture of several agents including SiC fibres, quartz, cristobalite, non-fibrous SiC and sulphur dioxide. Exposure levels were generally below the current Norwegian OELs; however, high exposure to fibres and respirable dust still occurs in the furnace department. PMID:18550624

Impact of planetary ball milling parameters on the microstructure and pinning properties of polycrystalline superconductor Y3Ba5Cu8Oy

NASA Astrophysics Data System (ADS)

Slimani, Y.; Hannachi, E.; Azzouz, F. Ben; Salem, M. Ben

2018-06-01

We have reported the influence of planetary high energy ball milling parameters on morphology, microstructure and flux pinning capability of polycrystalline Y3Ba5Cu8Oy. Samples were prepared through the standard solid-state reaction by using two different milling methods, ball milling in a planetary crusher and hand grinding in a mortar. Phase analysis by X-ray diffraction (XRD) method, microstructural examination by scanning electron microscope (SEM), electrical resistivity, the global and intra-granular critical current densities measurements are done to characterize the samples. The processing parameters of the planetary milling have a considerable impact on the final product properties. SEM observations show the presence of nanoscale entities submerged within the Y3Ba5Cu8Oy crystallites. The results show that the fine grain microstructure of the Y3Ba5Cu8Oy bulk induced by ball milling process contributes to critical currents density enhancement in the magnetic field and promotes an optimized flux pinning ability.

Battery cycle life balancing in a microgrid through flexible distribution of energy and storage resources

NASA Astrophysics Data System (ADS)

Khasawneh, Hussam J.; Illindala, Mahesh S.

2014-09-01

In this paper, a microgrid consisting of four fuel cell-battery hybrid Distributed Energy Resources (DERs) is devised for an industrial crusher-conveyor load. Each fuel cell was accompanied by a Li-ion battery to provide energy storage support under islanded condition of the microgrid since the fuel cells typically have poor transient response characteristics. After carrying out extensive modeling and analysis in MATLAB®, the battery utilization was found to vary significantly based on the DER's 'electrical' placement within the microgrid. This paper presents, under such conditions, a variety of battery life balancing solutions through the use of the new framework of Flexible Distribution of EneRgy and Storage Resources (FDERS). It is based on an in-situ reconfiguration approach through 'virtual' reactances that help in changing the 'electrical' position of each DER without physically displacing any component in the system. Several possible approaches toward balancing the battery utilization are compared in this paper taking advantage of the flexibility that FDERS offers. It was observed that the estimated battery life is dependent on factors such as cycling sequence, pattern, and occurrence.

Specification of a new de-stoner machine: evaluation of machining effects on olive paste's rheology and olive oil yield and quality.

PubMed

Romaniello, Roberto; Leone, Alessandro; Tamborrino, Antonia

2017-01-01

An industrial prototype of a partial de-stoner machine was specified, built and implemented in an industrial olive oil extraction plant. The partial de-stoner machine was compared to the traditional mechanical crusher to assess its quantitative and qualitative performance. The extraction efficiency of the olive oil extraction plant, olive oil quality, sensory evaluation and rheological aspects were investigated. The results indicate that by using the partial de-stoner machine the extraction plant did not show statistical differences with respect to the traditional mechanical crushing. Moreover, the partial de-stoner machine allowed recovery of 60% of olive pits and the oils obtained were characterised by more marked green fruitiness, flavour and aroma than the oils produced using the traditional processing systems. The partial de-stoner machine removes the limitations of the traditional total de-stoner machine, opening new frontiers for the recovery of pits to be used as biomass. Moreover, the partial de-stoner machine permitted a significant reduction in the viscosity of the olive paste. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Voltage Controller Saves Energy, Prolongs Life of Motors

NASA Technical Reports Server (NTRS)

2007-01-01

In 1985, Power Efficiency Corporation of Las Vegas licensed NASA voltage controller technology from Marshall Space Flight Center. In the following years, Power Efficiency made patented improvements to the technology and marketed the resulting products throughout the world as the Performance Controller and the Power Efficiency energy-saving soft start. Soft start gradually introduces power to an electric motor, thus eliminating the harsh, violent mechanical stresses of having the device go from a dormant state to one of full activity; prevents it from running too hot; and increases the motor's lifetime. The product can pay for itself through the reduction in electricity consumed (according to Power Efficiency, within 3 years), depending on the duty cycle of the motor and the prevailing power rates. In many instances, the purchaser is eligible for special utility rebates for the environmental protection it provides. Common applications of Power Efficiency's soft start include mixers, grinders, granulators, conveyors, crushers, stamping presses, injection molders, elevators with MG sets, and escalators. The device has been retrofitted onto equipment at major department store chains, hotels, airports, universities, and for various manufacturers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raj K. Rajamani; Sanjeeva Latchireddi; Sravan K. Prathy

The U.S. mining industry operates approximately 80 semi-autogenesis grinding mills (SAG) throughout the United States. Depending on the mill size the SAG mills draws between 2 MW and 17 MW. The product from the SAG mill is further reduced in size using pebble crushers and ball mills. Hence, typical gold or copper ore requires between 2.0 and 7.5 kWh per ton of energy to reduce the particle size. Considering a typical mining operation processes 10,000 to 100,000 tons per day the energy expenditure in grinding is 50 percent of the cost of production of the metal. A research team frommore » the University of Utah is working to make inroads into saving energy in these SAG mills. In 2003, Industries of the Future Program of the Department of Energy tasked the University of Utah team to build a partnership between the University and the mining industry for the specific purpose of reducing energy consumption in SAG mills. A partnership was formed with Cortez Gold Mines, Kennecott Utah Copper Corporation, Process Engineering Resources Inc. and others. In the current project, Cortez Gold Mines played a key role in facilitating the 26-ft SAG mill at Cortez as a test mill for this study. According to plant personnel, there were a number of unscheduled shut downs to repair broken liners and the mill throughput fluctuated depending on ore type. The University team had two softwares, Millsoft and FlowMod to tackle the problem. Millsoft is capable of simulating the motion of charge in the mill. FlowMod calculates the slurry flow through the grate and pulp lifters. Based on this data the two models were fine-tuned to fit the Cortez SAG will. In the summer of 2004 a new design of shell lifters were presented to Cortez and in September 2004 these lifters were installed in the SAG mill. By December 2004 Cortez Mines realized that the SAG mill is drawing approximately 236-kW less power than before while maintaining the same level of production. In the first month there was extreme cycling and operators had to learn more. Now the power consumption is 0.3-1.3 kWh/ton lower than before. The actual SAG mill power draw is 230-370 kW lower. Mill runs 1 rpm lesser in speed on the average. The re-circulation to the cone crusher is reduced by 1-10%, which means more efficient grinding of critical size material is taking place in the mill. All of the savings have resulted in reduction of operating cost be about $0.023-$0.048/ ton.« less

Direct 40Ar/39Ar age determination of fluid inclusions using in-vacuo¬ stepwise crushing - Example of garnet from the Cycladic Blueschist Unit on Syros

NASA Astrophysics Data System (ADS)

Uunk, Bertram; Postma, Onno; Wijbrans, Jan; Brouwer, Fraukje

2017-04-01

Metamorphic minerals and veins commonly trap attending hydrous fluids in fluid inclusions, which yield a wealth of information on the history of the hosting metamorphic system. When these fluids are sufficiently saline, the KCl in the inclusions can be used as a K/Ar geochronologic system, potentially dating inclusion incorporation. Whilst primary fluid inclusions (PFIs) can date fluid incorporation during mineral or vein growth, secondary fluid inclusion trails (SFIs) can provide age constraints on later fluid flow events. At VU Amsterdam, a new in-vacuo crushing apparatus has been designed to extract fluid inclusions from minerals for 40Ar/39Ar analysis. Separates are crushed inside a crusher tube connected to a purification line and a quadrupole mass spectrometer. In-vacuo crushing is achieved by lifting and dropping a steel pestle using an externally controlled magnetic field. As the gas can be analyzed between different crushing steps, the setup permits stepwise crushing experiments. Additionally, crushed powder can be heated by inserting the crusher tube in an externally controlled furnace. Dating by 40Ar/39Ar stepwise crushing has the added advantage that, during neutron irradiation to produce 39Ar from 39K, 38Ar and 37Ar are also produced from 38Cl and 40Ca, respectively. Simultaneous analysis of these argon isotopes permits constraining the chemistry of the argon source sampled during the experiment. This allows a distinction between different fluid or crystal lattice sources. Garnet from three samples of the HP metamorphic Cycladic Blueschist Unit on Syros, Greece was stepwise crushed to obtain fluid inclusion ages. Initial steps for all three experiments yield significant components of excess argon, which are interpreted to originate from grain boundary fluids and secondary fluid inclusions trails. During subsequent steps, age results stabilize to a plateau age. One garnet from North Syros yields an unusually old 80 Ma plateau age. However, isochrons indicate the presence of excess argon in the PFIs and isochron ages overlap with other isotopic constraints on the age of garnet growth during eclogite metamorphism (55-50 Ma) in the underlying metabasite. Garnet from two samples from the center of Syros yields younger ages overlapping with greenschist overprinting (25-30 Ma). Further studies will indicate whether these younger ages reflect a young garnet growth age or a young fluid flow event affecting older garnet crystals. The stepwise crushing and heating approach shows to be effective in dating fluid inclusions in natural mineral systems. As many metamorphic processes occur under influence or in the presence of fluids, this method should greatly expand our possibilities to date crustal processes.

Characterization of Limestone as Raw Material to Hydrated Lime

NASA Astrophysics Data System (ADS)

Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

2018-03-01

In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

The utilization of stone ash on cellular lightweight concrete

NASA Astrophysics Data System (ADS)

Karolina, R.; Sianipar, Y. G. C.

2018-02-01

Lightweight concrete brick is a brick which made of cement, sand, water, and foam as the basic composition. This brick are divided into 2, based on the foam used such as AAC (Autoclave Aerated Concrete) that use aluminium paste and CLC(Cellular Lightweight Concrete) that use foaming agent from BASF as its foaming material. In this trial, the lightweight brick that are ging to be use are the CLC with foaming agent as its foaming material with the mixture of stone ash that are produced by the Stone Crusher with spesific gravity 2666 kg/m3 as their partly sand substitution . In this research, the stone ash variant that are used are 10%, 15%, and 20% from the amount of sand that planned before. After casting, the result of the 10% will receive a reduction of compressive strength while an increasing in absorption as 25.07% and 39.005% and the 15% variant will recieve a reduction of compressive strength as much as 65.8% and a reduction of absorption as much as 17.441% and the 20% variant will recieve a reduction of compressive strength as much as 67.4% while an increasing of absorption as much as 17.956%.

Operation Greenhouse. Scientific Director's report of atomic weapon tests at Eniwetok, 1951. Annex 1. 6, blast measurements. Part 3. Pressure near ground level. Section 4. Blast asymmetry from aerial photographs. Section 5. Ball-crusher-gauge measurements of peak pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-04-01

Aerial motion pictures from manned aircraft were taken of the Dog, Easy, and George Shots and from a drone aircraft on Dog Shot to determine whether asymmetries in the blast waves could be detected and measured. Only one film, that taken of Dog Shot from a drone, was considered good enough to warrant detailed analysis, but this failed to yield any positive information on asymmetries. The analysis showed that failure to obtain good arrival-time data arose from a number of cases, but primarily from uncertainities in magnification and timing. Results could only be matched with reliable data from blast-velocity switchesmore » by use of large corrections. Asymnetries, if present, were judged to have been too small or to have occurred too early to be detected with the slow-frame speed used. Recommendations for better results include locating the aircraft directly overhead at the time of burst and using a camera having greater frame speed and provided with timing marks.« less

Some remarks on recent developments in micropolar continuum theory

NASA Astrophysics Data System (ADS)

Vilchevskaya, E. N.; Müller, W. H.

2018-04-01

This paper considers micropolar media that can undergo structural changes and do not a priori consist of indestructible material particles. Initially the pertinent literature is reviewed. Then the necessary theoretical framework for a continuum of that type is presented. The standard macroscopic equations for mass, linear and angular momentum are complemented by a recently proposed balance for the moment of inertia tensor, which contains a production term. Two examples illustrate the effect of the production. In the first example, we study a continuous stream of matter on a conveyor belt going through a crusher so that the total number of particles will change. In context with this example, it is also clear that the traditional Lagrangian way of describing the motion of solids is no longer adequate and must be replaced by the Eulerian point of view known from fluid mechanics. The second example deals with hollow particles which rotate because of the presence of body couples. Now a transient temperature field is superimposed such that the moment of inertia field changes due to the thermal expansion of particles. This in turn results in rotational motion that is no longer constant but varies in space and time.

Investigation of coal properties and airborne respirable dust generation. Report of investigations/1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Organiscak, J.A.; Page, S.J.

1998-10-01

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grindability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated withmore » ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss (ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-micrometers coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.« less

RESOLVE 2010 Field Test

NASA Technical Reports Server (NTRS)

Captain, J.; Quinn, J.; Moss, T.; Weis, K.

2010-01-01

This slide presentation reviews the field tests conducted in 2010 of the Regolith Environment Science & Oxygen & Lunar Volatile Extraction (RESOLVE). The Resolve program consist of several mechanism: (1) Excavation and Bulk Regolith Characterization (EBRC) which is designed to act as a drill and crusher, (2) Regolith Volatiles Characterization (RVC) which is a reactor and does gas analysis,(3) Lunar Water Resources Demonstration (LWRD) which is a fluid system, water and hydrogen capture device and (4) the Rover. The scientific goal of this test is to demonstrate evolution of low levels of hydrogen and water as a function of temperature. The Engineering goals of this test are to demonstrate:(1) Integration onto new rover (2) Miniaturization of electronics rack (3) Operation from battery packs (elimination of generator) (4) Remote command/control and (5) Operation while roving. Views of the 2008 and the 2010 mechanisms, a overhead view of the mission path, a view of the terrain, the two drill sites, and a graphic of the Master Events Controller Graphical User Interface (MEC GUI) are shown. There are descriptions of the Gas chromatography (GC), the operational procedure, water and hydrogen doping of tephra. There is also a review of some of the results, and future direction for research and tests.

Shale-oil-recovery systems incorporating ore beneficiation. Final report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weiss, M.A.; Klumpar, I.V.; Peterson, C.R.

This study analyzed the recovery of oil from oil shale by use of proposed systems which incorporate beneficiation of the shale ore (that is concentration of the kerogen before the oil-recovery step). The objective was to identify systems which could be more attractive than conventional surface retorting of ore. No experimental work was carried out. The systems analyzed consisted of beneficiation methods which could increase kerogen concentrations by at least four-fold. Potentially attractive low-enrichment methods such as density separation were not examined. The technical alternatives considered were bounded by the secondary crusher as input and raw shale oil as output.more » A sequence of ball milling, froth flotation, and retorting concentrate is not attractive for Western shales compared to conventional ore retorting; transporting the concentrate to another location for retorting reduces air emissions in the ore region but cost reduction is questionable. The high capital and energy cost s results largely from the ball milling step which is very inefficient. Major improvements in comminution seem achievable through research and such improvements, plus confirmation of other assumptions, could make high-enrichment beneficiation competitive with conventional processing. 27 figures, 23 tables.« less

FPGA Implementation of Stereo Disparity with High Throughput for Mobility Applications

NASA Technical Reports Server (NTRS)

Villalpando, Carlos Y.; Morfopolous, Arin; Matthies, Larry; Goldberg, Steven

2011-01-01

High speed stereo vision can allow unmanned robotic systems to navigate safely in unstructured terrain, but the computational cost can exceed the capacity of typical embedded CPUs. In this paper, we describe an end-to-end stereo computation co-processing system optimized for fast throughput that has been implemented on a single Virtex 4 LX160 FPGA. This system is capable of operating on images from a 1024 x 768 3CCD (true RGB) camera pair at 15 Hz. Data enters the FPGA directly from the cameras via Camera Link and is rectified, pre-filtered and converted into a disparity image all within the FPGA, incurring no CPU load. Once complete, a rectified image and the final disparity image are read out over the PCI bus, for a bandwidth cost of 68 MB/sec. Within the FPGA there are 4 distinct algorithms: Camera Link capture, Bilinear rectification, Bilateral subtraction pre-filtering and the Sum of Absolute Difference (SAD) disparity. Each module will be described in brief along with the data flow and control logic for the system. The system has been successfully fielded upon the Carnegie Mellon University's National Robotics Engineering Center (NREC) Crusher system during extensive field trials in 2007 and 2008 and is being implemented for other surface mobility systems at JPL.

The Optimum Production Method for Quality Improvement of Recycled Aggregates Using Sulfuric Acid and the Abrasion Method.

PubMed

Kim, Haseog; Park, Sangki; Kim, Hayong

2016-07-29

There has been increased deconstruction and demolition of reinforced concrete structures due to the aging of the structures and redevelopment of urban areas resulting in the generation of massive amounts of construction. The production volume of waste concrete is projected to increase rapidly over 100 million tons by 2020. However, due to the high cement paste content, recycled aggregates have low density and high absorption ratio. They are mostly used for land reclamation purposes with low added value instead of multiple approaches. This study was performed to determine an effective method to remove cement paste from recycled aggregates by using the abrasion and substituting the process water with acidic water. The aim of this study is to analyze the quality of the recycled fine aggregates produced by a complex method and investigate the optimum manufacturing conditions for recycled fine aggregates based on the design of experiment. The experimental parameters considered were water ratio, coarse aggregate ratio, and abrasion time and, as a result of the experiment, data concerning the properties of recycled sand were obtained. It was found that high-quality recycled fine aggregates can be obtained with 8.57 min of abrasion-crusher time and a recycled coarse aggregate ratio of over 1.5.

Physical and mechanical properties of quarry dust waste incorporated into fired clay brick

NASA Astrophysics Data System (ADS)

Kadir, A. A.; Hassan, M. I. H.; Sarani, N. A.; Rahim, A. S. Abdul; Ismail, N.

2017-04-01

A large amount of quarry dust waste is dispose into landfills every year. This waste was obtained as a by-product during the production of aggregates through the crushing process of rocks in rubble crusher units. The increasing value of waste will have significant impact towards health and environment. Recycling such wastes by incorporating them into building materials is a practical solution for pollution problem. Therefore, this research was to examine the possibility of quarry dust to be incorporated in fired clay bricks. In this research, the composition and concentration of heavy metals were determined by using X-Ray Fluorescence Spectrometer (XRF). The research also consists of physical and mechanical properties of the fired clay bricks by utilizing quarry dust waste. Brick was manufactured by incorporating different percentages of quarry dust waste which are 0%, 10%, 20% and 30%. All bricks sample was tested with physical and mechanical properties which were density, shrinkage, initial rate of suction (IRS) and compressive strength of the fired bricks. Furthermore, the density and shrinkage were also in standard range. All physical and mechanical results were complied with the BS 3921:1985 standard. The comprehensive experimental work described in this research investigated the possibility of incorporating quarry dust into fired clay bricks. These materials could be an alternative low cost material for brick and at the same time provide a new disposal method for the waste.

Life Cycle Assessment for the Production of Oil Palm Seeds

PubMed Central

Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

2014-01-01

The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change. PMID:27073598

3D bioprinting of BMSC-laden methacrylamide gelatin scaffolds with CBD-BMP2-collagen microfibers.

PubMed

Du, Mingchun; Chen, Bing; Meng, Qingyuan; Liu, Sumei; Zheng, Xiongfei; Zhang, Cheng; Wang, Heran; Li, Hongyi; Wang, Nuo; Dai, Jianwu

2015-12-18

Three-dimensional (3D) bioprinting combines biomaterials, cells and functional components into complex living tissues. Herein, we assembled function-control modules into cell-laden scaffolds using 3D bioprinting. A customized 3D printer was able to tune the microstructure of printed bone mesenchymal stem cell (BMSC)-laden methacrylamide gelatin scaffolds at the micrometer scale. For example, the pore size was adjusted to 282 ± 32 μm and 363 ± 60 μm. To match the requirements of the printing nozzle, collagen microfibers with a length of 22 ± 13 μm were prepared with a high-speed crusher. Collagen microfibers bound bone morphogenetic protein 2 (BMP2) with a collagen binding domain (CBD) as differentiation-control module, from which BMP2 was able to be controllably released. The differentiation behaviors of BMSCs in the printed scaffolds were compared in three microenvironments: samples without CBD-BMP2-collagen microfibers in the growth medium, samples without microfibers in the osteogenic medium and samples with microfibers in the growth medium. The results indicated that BMSCs showed high cell viability (>90%) during printing; CBD-BMP2-collagen microfibers induced BMSC differentiation into osteocytes within 14 days more efficiently than the osteogenic medium. Our studies suggest that these function-control modules are attractive biomaterials and have potential applications in 3D bioprinting.

Life Cycle Assessment for the Production of Oil Palm Seeds.

PubMed

Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

2014-12-01

The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change.

Efficient coupling of Sec23-Sec24 to Sec13-Sec31 drives COPII-dependent collagen secretion and is essential for normal craniofacial development.

PubMed

Townley, Anna K; Feng, Yi; Schmidt, Katy; Carter, Deborah A; Porter, Robert; Verkade, Paul; Stephens, David J

2008-09-15

The COPII coat assembles on endoplasmic reticulum membranes to coordinate the collection of secretory cargo with the formation of transport vesicles. During COPII assembly, Sar1 deforms the membrane and recruits the Sec23-Sec24 complex (Sec23/24), which is the primary cargo-binding adaptor for the system, and Sec13-Sec31 (Sec13/31), which provides a structural outer layer for vesicle formation. Here we show that Sec13 depletion results in concomitant loss of Sec31 and juxtanuclear clustering of pre-budding complexes containing Sec23/24 and cargo. Electron microscopy reveals the presence of curved coated profiles on distended endoplasmic reticulum, indicating that Sec13/31 is not required for the generation or maintenance of the curvature. Surprisingly, export of tsO45-G-YFP, a marker of secretory cargo, is unaffected by Sec13/31 depletion; by contrast, secretion of collagen from primary fibroblasts is strongly inhibited. Suppression of Sec13 expression in zebrafish causes defects in proteoglycan deposition and skeletal abnormalities that are grossly similar to the craniofacial abnormalities of crusher mutant zebrafish and patients with cranio-lenticulo-sutural dysplasia. We conclude that efficient coupling of the inner (Sec23/24) and outer (Sec13/31) layers of the COPII coat is required to drive the export of collagen from the endoplasmic reticulum, and that highly efficient COPII assembly is essential for normal craniofacial development during embryogenesis.

PaR Tensile Truss for Nuclear Decontamination and Decommissioning - 12467

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doebler, Gary R.

2012-07-01

Remote robotics and manipulators are commonly used in nuclear decontamination and decommissioning (D and D) processes. D and D robots are often deployed using rigid telescoping masts in order to apply and counteract side loads. However, for very long vertical reaches (15 meters or longer) and high lift capacities, a telescopic is usually not practical due to the large cross section and weight required to make the mast stiff and resist seismic forces. For those long vertical travel applications, PaR Systems has recently developed the Tensile Truss, a rigid, hoist-driven 'structure' that employs six independent wire rope hoists to achievemore » long vertical reaches. Like a mast, the Tensile Truss is typically attached to a bridge-mounted trolley and is used as a platform for robotic manipulators and other remotely operated tools. For suspended, rigid deployment of D and D tools with very long vertical reaches, the Tensile Truss can be a better alternative than a telescoping mast. Masts have length limitations that can make them impractical or unworkable as lengths increase. The Tensile Truss also has the added benefits of increased safety, ease of decontamination, superior stiffness and ability to withstand excessive side loading. A Tensile Truss system is currently being considered for D and D operations and spent fuel recovery at the Fukushima Daiichi Nuclear Power Plant in Japan. This system will deploy interchangeable tools such as underwater hydraulic manipulators, hydraulic shears and crushers, grippers and fuel grapples. (authors)« less

Compounded Apixaban Suspensions for Enteral Feeding Tubes.

PubMed

Caraballo, Maria L; Donmez, Seda; Nathan, Kobi; Zhao, Fang

2017-07-01

Objective: There is limited information on compounded apixaban formulations for administration via enteral feeding tubes. This study was designed to identify a suitable apixaban suspension formulation that is easy to prepare in a pharmacy setting, is compatible with commonly used feeding tubes, and has a beyond-use date of 7 days. Methods: Apixaban suspensions were prepared from commercially available 5-mg Eliquis tablets. Several vehicles and compounding methods were screened for ease of preparation, dosage accuracy, and tube compatibility. Two tubing types, polyurethane and polyvinyl chloride, with varying lengths and diameters, were included in the study. They were mounted on a peg board during evaluation to mimic the patient body position. A 7-day stability study of the selected formulation was also conducted. Results: Vehicles containing 40% to 60% Ora-Plus in water all exhibited satisfactory flowability through the tubes. The mortar/pestle compounding method was found to produce more accurate and consistent apixaban suspensions than the pill crusher or crushing syringe method. The selected formulation, 0.25 mg/mL apixaban in 50:50 Ora-Plus:water, was compatible with both tubing types, retaining >98% drug in posttube samples. The stability study also confirmed that this formulation was stable physically and chemically over 7 days of storage at room temperature. Conclusions: A suitable apixaban suspension formulation was identified for administration via enteral feeding tubes. The formulation consisted of 0.25 mg/mL apixaban in 50:50 Ora-Plus:water. The stability study results supported a beyond-use date of 7 days at room temperature.

Using a noise monitoring station in a small quarry located in an urban area.

PubMed

Wichers, Michiel; Iramina, Wilson Siguemasa; de Eston, Sérgio Médici; Ayres da Silva, Anna Luiza Marques

2017-12-22

Mining plays an important role in Brazilian exports. On the other hand, large urban centers like São Paulo, with approximately 21 million inhabitants, also demand an increasing domestic consumption of natural resources, such as construction aggregate. There are many quarries located in the surroundings of urban centers in Brazil, competing with the growth of urbanized areas. Such proximity leads to a series of conflicts involving quarries and surrounding communities, where the increase in noise levels is highlighted. Operations in quarries, in general, are intermittent. Noisier equipment, such as drilling rigs and primary crushers, operates only a few hours during the day, while other operations, such as screening and secondary and tertiary crushing, are more constant. This paper presents a study carried out in a quarry located near São Paulo, where in addition to conventional short term noise measurements at surrounding receptors, one noise monitoring station was installed, allowing to identify the noisiest moments during the quarry operating time. Through data transmitted by wireless technology, it was possible to follow the noise variations emitted from mining activities in real time and observe the noisiest events that were recorded for events that exceeded the established standards. A mobile application associated to this monitoring station facilitated the quarry's manager and employees to access immediately the monitoring information. Therefore, by using this system, it was possible to evaluate the effectiveness of noise reduction measures already taken and indicate what steps still need to be held.

Laboratory-Induced Cue Reactivity among Individuals with Prescription Opioid Dependence

PubMed Central

Back, Sudie E.; Gros, Daniel F.; McCauley, Jenna; Flanagan, Julianne; Cox, Elizabeth; Barth, Kelly; Brady, Kathleen T.

2014-01-01

Prescription opioid (PO) dependence is a critical health problem. Although examination of drug cue reactivity paradigms has advanced the understanding of risk factors for relapse for a variety of substances (e.g., cocaine, alcohol, nicotine), no PO specific drug cue paradigm has been developed. The current study addressed this gap in the literature and evaluated the ability of a newly developed PO drug cue paradigm to elicit subjective, physiological, and neuroendocrine changes among PO-dependent participants (n = 20) as compared to controls (n = 17). The drug cue paradigm included an induction script, viewing and handling paraphernalia (e.g., bottle of oxycontin pills, pill crusher) and watching a video depicting people using POs as well as places related to POs (e.g., pharmacies). Consistent with hypotheses, the PO group demonstrated significant pre- to post-cue increases on subjective ratings of craving, difficulty resisting POs, stress, and anger. The control group did not demonstrate significant changes on any of the subjective measures. Both the PO group and the control group evidenced significant pre- to post-cue increases in physiological responses (e.g., blood pressure, skin conductance), as expected given the arousing nature of the drug cue stimuli. The PO group, but not the control group, evidenced a significant pre- to post-cue increase in heart rate and salivary cortisol levels. The development and validation of a drug cue paradigm for POs may help inform future research and treatment development efforts for patients with PO dependence. PMID:24813546

Interfacial and mechanical property analysis of waste printed circuit boards subject to thermal shock.

PubMed

Li, Jinhui; Duan, Huabo; Yu, Keli; Wang, Siting

2010-02-01

Waste printed circuit boards (PCBs) are the focal points for handling electric and electronic waste. In this paper, a thermal shock method was used to pretreat waste PCBs for the improvement of crushing performance. The influence of the thermal shock process on interfacial modification and mechanical property attenuation of PCB waste was studied. The appearance and layer spacing of the basal plane began to change slightly when the temperature reached 200 degrees C. By 250 degrees C, apparent bulging, cracking, and delamination were observed. However, pyrolysis of PCBs occurred when the temperature reached 275 degrees C, where PCBs were carbonized. The thermogravimetric analysis of PCB particles under vacuum showed that 270 degrees C was the starting point of pyrolysis. The tensile and impact strength of PCBs were reduced as shock temperature rose gradually, with a reduction by 2.6 and 16.5%, respectively, at 250 degrees C from its unheated strength. The PCBs that were heated to 250 degrees C achieved 100% liberation, increasing linearly from 13.6% for unheated PCBs through a single-level shear-crusher (2-mm mesh) and resulting in an obvious reduction of 9.5% (dB) in dust and noise at 250 degrees C. These parameters could be helpful for establishing the operational setup for industrial-scale facilities with the aim of achieving a compact process and a highly efficient recovery for waste PCBs compared with those of the traditional combination mechanical technologies.

[Mustard gas bombs found astray in the Faxaflói bay. Mustard gas: usage and poisonings].

PubMed

Kristinsson, Jakop; Jóhannesson, Thorkell

2009-05-01

The finding in 1972 of two World War II mustard gas artillery shells in crushed shell sediment dredged in the Faxaflói Bay and transported as raw material for cement production at Akranes (Western Iceland) is reported. One of the shells was wedged in a stone crusher in the raw material processing line and was ruptured. As a result dark fluid with a garlic like smell seeped out from the metal canister. The attending employees believed the metal object to be inert and tried to cut it out with a blow torch. This resulted in the explosion of the shell charge and in the exposure of four employees to mustard gas. All suffered burns on their hands and two of them in the eyes also. The second shell was detonated in the open at a distance from the factory. Emphasis is given to the fact that instant, or at least as soon as possible, cleansing and washing is the most efficient measure to be taken against the debilitating effects of mustard gas. It is also pointed out that the active principle in mustard gas (dichlorodiethyl sulphide) can easily be synthesized and none of the precursor substances are subjected to any restrictions of use. The authors conclude that mustard gas bombs may still be found in the arsenals of some military powers in spite of an international convention that prohibits the production, stockpiling and the use of chemical weapons. Terrorist groups have also seemingly tried to aquire mustard gas bombs and other chemical weapons. Therefore cases of mustard gas poisoning might still occur.

Evaluation of Rock Powdering Methods to Obtain Fine-grained Samples for CHEMIN, a Combined XRD/XRF Instrument

NASA Technical Reports Server (NTRS)

Chipera, S. J.; Vaniman, D. T.; Bish, D. L.; Sarrazin, P.; Feldman, S.; Blake, D. F.; Bearman, G.; Bar-Cohen, Y.

2004-01-01

A miniature XRD/XRF (X-ray diffraction / X-ray fluorescence) instrument, CHEMIN, is currently being developed for definitive mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed to enable remote XRD analysis is how best to obtain a representative sample powder for analysis. For powder XRD analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a two-dimensional detector as used in the CHEMIN instrument will produce good results even with poorly prepared powder, the quality of the data will improve and the time required for data collection will be reduced if the sample is fine-grained and randomly oriented. A variety of methods have been proposed for XRD sample preparation. Chipera et al. presented grain size distributions and XRD results from powders generated with an Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL. The USDC was shown to be an effective instrument for sampling rock to produce powder suitable for XRD. In this paper, we compare powder prepared using the USDC with powder obtained with a miniaturized rock crusher developed at JPL and with powder obtained with a rotary tungsten carbide bit to powders obtained from a laboratory bench-scale Retsch mill (provides benchmark mineralogical data). These comparisons will allow assessment of the suitability of these methods for analysis by an XRD/XRF instrument such as CHEMIN.

The effectiveness of stone ash and volcanic ash of mount Sinabung as a filler on the initial strength of self-compacting concrete

NASA Astrophysics Data System (ADS)

Karolina, R.; Muhammad, W.; Saragih, M. D. S. M.; Mustaqa, T.

2018-02-01

Self Compacting Concrete is a concrete variant that has a high degree of workability and also has great initial strength, but low water cement factor. It is also self-flowable that can be molded on formwork with a very little or no compacted use of compactors. This concrete, using a variety of aggregate sizes, aggregate portions and superplasticizer admixture to achieve a special viscosity that allows it to flow on its own without the aid of a compactor. Lightweight concrete brick is a type of brick made from cement, sand, water, and developers. Lightweight concrete bricks are divided into 2 based on the developed materials used are AAC (Autoclave Aerated Concrete) using aluminum paste and CLC (Cellular Lightweight Concrete) that use Foaming Agent from BASF as a developer material. In this experiment, the lightweight bricks that will be made are CLC type which uses Foaming Agent as the developer material by mixing the Ash Stone produced by Stone Crusher machine which has the density of 2666 kg / m3 as Partial Pair Substitution. In this study the variation of Ash Stone used is 10%, 15%, and 20% of the planned amount of sand. After doing the tasting the result is obtained for 10% variation. Compressive Strength and Absorption Increase will decrease by 25.07% and 39.005% and Variation of 15% compressive strength will decrease by 65,8% and decrease of absorbtion equal to 17,441% and variation of 20% compressive strength will decreased by 67,4 and absorption increase equal to 17,956%.

Handling of quarry waste from schist production at Oppdal, Norway

NASA Astrophysics Data System (ADS)

Willy Danielsen, Svein; Alnæs, Lisbeth; Azrague, Kamal; Suleng, Jon

2017-04-01

Handling of quarry waste from schist production at Oppdal, Norway Svein Willy Danielsen1), Lisbeth Alnæs2), Kamal Azrague2), Jon Suleng3) 1) Geomaterials Consultant, Trondheim Norway, 2) SINTEF, Trondheim, Norway, 3) AF Gruppen AS, Oppdal, Norway A significant amount of aggregate research in Norway has been focused on the recovery and use of surplus sizes from hard rock aggregate quarries. The use of sand sized quarry waste (QW) from crushing/processing has been motivated by the rapid depletion of traditional sand/gravel resources, increasing land-use conflicts, and the need to minimise QW deposits which for some quarries are becoming a critical factor for economy as well as for environmental reasons. With an annual aggregate production of 77 million tons, out of which approximately 83 % comes from hard rock, the annual volume of size < 4 mm will be of the order of 19 million tons. Converting this into construction aggregates is a major challenge in order to obtain satisfactory mass balance. This challenge is even bigger for quarries producing decorative stones. E.g. the quarrying and production of schist products for building purpose normally utilises as little as 10-15 % of the excavated rock. Oppdal in central Norway is a main supplier of schist products for flooring, roofing and decorative purpose. The high percentage of QW is due to strict requirements to the finished products, both regarding processing and the character of the parent rock. The need to deposit large amounts of QW is a serious setback for the quarry economy. Within a limited time horizon the volumes of QW can threaten the further exploitation by merely choking the quarry. On the opposite side - any process that can convert the QW into sellable products will give a tremendous added value for the producer. Besides, the area in question is about to drain out its available aggregate resources, having to rely on long-transported sand and gravel. This has consequences not only for the economy, but also for the environment since heavy lorry transport will not be sustainable. An on-going project is now looking into converting the QW into quality aggregate both for road construction and concrete. Novel crusher technology and processing strategy is being applied and adapted, and the finished products will be tested in laboratories to establish the relevant application parameters and obtainable quality. By producing coarse aggregates for primarily road purpose, it is estimated that the QW can be reduced from todaýs approx. 90 % to approx. 40 %. The potential by also installing the latest inventions of crusher technology designed for making manufactured sand, is to further reduce QW down to < 10 %. Making all these materials sellable in the market, the economic - and also environmental - potential will be considerable. Understanding the geological conditions and petrographic properties of the rock is vital. This is a quartz-feldspar rich metamorphic rock - a meta-arkose - containing rhythmically distributed planar lamina (less than 2 mm thick) or scattered occurrence of mica, separated by layers composed predominately of quartz and feldspar. The rock can be split along the lamina to slabs varying from 0.5 cm to more than 10 cm in thickness, and the microstructure can be characterized as being granoblastic to gneissic. . This makes it possible by well designed crushing process and careful selection of the in-going rock particles, to obtain well shaped aggregates up to at least 20 mm. The on-going project will also study the total cost situation depending on the QW utilisation, discuss the environmental and sustainability issues with a societal perspective, and also consider the market opportunities.

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan.

PubMed

Chang, Chang-Tang; Chang, Yu-Min; Lin, Wen-Yinn; Wu, Ming-Ching

2010-10-01

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.

Quiet echo planar imaging for functional and diffusion MRI

PubMed Central

Price, Anthony N.; Cordero‐Grande, Lucilio; Malik, Shaihan; Ferrazzi, Giulio; Gaspar, Andreia; Hughes, Emer J.; Christiaens, Daan; McCabe, Laura; Schneider, Torben; Rutherford, Mary A.; Hajnal, Joseph V.

2017-01-01

Purpose To develop a purpose‐built quiet echo planar imaging capability for fetal functional and diffusion scans, for which acoustic considerations often compromise efficiency and resolution as well as angular/temporal coverage. Methods The gradient waveforms in multiband‐accelerated single‐shot echo planar imaging sequences have been redesigned to minimize spectral content. This includes a sinusoidal read‐out with a single fundamental frequency, a constant phase encoding gradient, overlapping smoothed CAIPIRINHA blips, and a novel strategy to merge the crushers in diffusion MRI. These changes are then tuned in conjunction with the gradient system frequency response function. Results Maintained image quality, SNR, and quantitative diffusion values while reducing acoustic noise up to 12 dB (A) is illustrated in two adult experiments. Fetal experiments in 10 subjects covering a range of parameters depict the adaptability and increased efficiency of quiet echo planar imaging. Conclusion Purpose‐built for highly efficient multiband fetal echo planar imaging studies, the presented framework reduces acoustic noise for all echo planar imaging‐based sequences. Full optimization by tuning to the gradient frequency response functions allows for a maximally time‐efficient scan within safe limits. This allows ambitious in‐utero studies such as functional brain imaging with high spatial/temporal resolution and diffusion scans with high angular/spatial resolution to be run in a highly efficient manner at acceptable sound levels. Magn Reson Med 79:1447–1459, 2018. © 2017 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. PMID:28653363

NASA Tech Briefs, November 2009

NASA Technical Reports Server (NTRS)

2009-01-01

Topics covered include: Cryogenic Chamber for Servo-Hydraulic Materials Testing; Apparatus Measures Thermal Conductance Through a Thin Sample from Cryogenic to Room Temperature; Rover Attitude and Pointing System Simulation Testbed; Desktop Application Program to Simulate Cargo-Air-Drop Tests; Multimodal Friction Ignition Tester; Small-Bolt Torque-Tension Tester; Integrated Spacesuit Audio System Enhances Speech Quality and Reduces Noise; Hardware Implementation of a Bilateral Subtraction Filter; Simple Optoelectronic Feedback in Microwave Oscillators; Small X-Band Oscillator Antennas; Free-Space Optical Interconnect Employing VCSEL Diodes; Discrete Fourier Transform Analysis in a Complex Vector Space; Miniature Scroll Pumps Fabricated by LIGA; Self-Assembling, Flexible, Pre-Ceramic Composite Preforms; Flight-speed Integral Image Analysis Toolkit; Work Coordination Engine; Multi-Mission Automated Task Invocation Subsystem; Autonomously Calibrating a Quadrupole Mass Spectrometer; Determining Spacecraft Reaction Wheel Friction Parameters; Composite Silica Aerogels Opacified with Titania; Multiplexed Colorimetric Solid-Phase Extraction; Detecting Airborne Mercury by Use of Polymer/Carbon Films; Lattice-Matched Semiconductor Layers on Single Crystalline Sapphire Substrate; Pressure-Energized Seal Rings to Better Withstand Flows; Rollerjaw Rock Crusher; Microwave Sterilization and Depyrogenation System; Quantifying Therapeutic and Diagnostic Efficacy in 2D Microvascular Images; NiF2/NaF:CaF2/Ca Solid-State High-Temperature Battery Cells; Critical Coupling Between Optical Fibers and WGM Resonators; Microwave Temperature Profiler Mounted in a Standard Airborne Research Canister; Alternative Determination of Density of the Titan Atmosphere; Solar Rejection Filter for Large Telescopes; Automated CFD for Generation of Airfoil Performance Tables; Progressive Classification Using Support Vector Machines; Active Learning with Irrelevant Examples; A Data Matrix Method for Improving the Quantification of Element Percentages of SEM/EDX Analysis; Deployable Shroud for the International X-Ray Observatory; Improved Model of a Mercury Ring Damper; Optoelectronic pH Meter: Further Details; X-38 Advanced Sublimator; and Solar Simulator Represents the Mars Surface Solar Environment.

Choice of reference measurements affects quantification of long diffusion time behaviour using stimulated echoes.

PubMed

Kleinnijenhuis, Michiel; Mollink, Jeroen; Lam, Wilfred W; Kinchesh, Paul; Khrapitchev, Alexandre A; Smart, Sean C; Jbabdi, Saad; Miller, Karla L

2018-02-01

To demonstrate how reference data affect the quantification of the apparent diffusion coefficient (ADC) in long diffusion time measurements with diffusion-weighted stimulated echo acquisition mode (DW-STEAM) measurements, and to present a modification to avoid contribution from crusher gradients in DW-STEAM. For DW-STEAM, reference measurements at long diffusion times have significant b 0 value, because b = 0 cannot be achieved in practice as a result of the need for signal spoiling. Two strategies for acquiring reference data over a range of diffusion times were considered: constant diffusion weighting (fixed-b 0 ) and constant gradient area (fixed-q 0 ). Fixed-b 0 and fixed-q 0 were compared using signal calculations for systems with one and two diffusion coefficients, and experimentally using data from postmortem human corpus callosum samples. Calculations of biexponential diffusion decay show that the ADC is underestimated for reference images with b > 0, which can induce an apparent time-dependence for fixed-q 0 . Restricted systems were also found to be affected. Experimentally, the exaggeration of the diffusion time-dependent effect under fixed-q 0 versus fixed-b 0 was in a range predicted theoretically, accounting for 62% (longitudinal) and 35% (radial) of the time dependence observed in white matter. Variation in the b-value of reference measurements in DW-STEAM can induce artificial diffusion time dependence in ADC, even in the absence of restriction. Magn Reson Med 79:952-959, 2018. © 2017 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. © 2017 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine.

WE-FG-206-05: New Arterial Spin Labeling Method for Simultaneous Estimation of Arterial Cerebral Blood Volume, Cerebral Blood Flow and Arterial Transit Time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, M; Whitlow, C; Jung, Y

Purpose: To demonstrate the feasibility of a novel Arterial Spin Labeling (ASL) method for simultaneously measuring cerebral blood flow (CBF), arterial transit time (ATT), and arterial cerebral blood volume (aCBV) without the use of a contrast agent. Methods: A series of multi-TI ASL images were acquired from one healthy subject on a 3T Siemens Skyra, with the following parameters: PCASL labeling with variable TI [300, 400, 500, 600, 700, 800, 900, 1000, 1500, 2000, 2500, 3000, 3500, 4000] ms, labeling bolus 1400 ms when TI allows, otherwise 100 ms less than TI, TR was minimized for each TI, two sincmore » shaped pre-saturation pulses were applied in the imaging plane immediately before 2D EPI acquisition. 64×64×24 voxels, 5 mm slice thickness, 1 mm gap, full brain coverage, 6 averages per TI, no crusher gradients, 11 ms TE, scan time of 4:56. The perfusion weighted time-series was created for each voxel and fit to a novel model. The model has two components: 1) the traditional model developed by Buxton et al., accounting for CBF and ATT, and 2) a box car function characterizing the width of the labeling bolus, with variable timing and height in proportion to the aCBV. All three parameters were fit using a nonlinear fitting routine that constrained all parameters to be positive. The main purpose of the high-temporal resolution TI sampling for the first second of data acquisition was to precisely estimate the blood volume component for better detection of arrival time and magnitude of signal. Results: Whole brain maps of CBF, ATT, and aCBV were produced, and all three parameters maps are consistent with similar maps described in the literature. Conclusion: Simultaneous mapping of CBF, ATT, and aCBV is feasible with a clinically tractable scan time (under 5 minutes).« less

Recovery of metals from waste printed circuit boards by a mechanical method using a water medium.

PubMed

Duan, Chenlong; Wen, Xuefeng; Shi, Changsheng; Zhao, Yuemin; Wen, Baofeng; He, Yaqun

2009-07-15

Research on the recycling of waste printed circuit boards (PCB) is at the forefront of environmental pollution prevention and resource recycling. To effectively crush waste PCB and to solve the problem of secondary pollution from fugitive odors and dust created during the crushing process, a wet impacting crusher was employed to achieve comminution liberation of the PCB in a water medium. The function of water in the crushing process was analyzed. When using slippery hammerheads, a rotation speed of 1470 rpm, a water flow of 6m(3)/h and a sieve plate aperture of 2.2mm, 95.87% of the crushed product was sized less than 1mm. 94.30% of the metal was in this grade of product. Using smashed material graded -1mm for further research, a Falcon concentrator was used to recover the metal from the waste PCB. Engineering considerations were the liberation degree, the distribution ratio of the metal and a way to simplify the technology. The separation mechanism for fine particles of different densities in a Falcon concentrator was analyzed in detail and the separation process in the segregation and separation zones was deduced. Also, the magnitude of centrifugal acceleration, the back flow water pressure and the feed slurry concentration, any of which might affect separation results, were studied. A recovery model was established using Design-Expert software. Separating waste PCB, crushed to -1mm, with the Falcon separator gave a concentrated product graded 92.36% metal with a recovery of 97.05%. To do this the reverse water pressure was 0.05 MPa, the speed transducer frequency was set at 30 Hz and the feed density was 20 g/l. A flow diagram illustrating the new technique of wet impact crushing followed by separation with a Falcon concentrator is provided. The technique will prevent environmental pollution from waste PCB and allow the effective recovery of resources. Water was used as the medium throughout the whole process.

Approaches to Enable Demand Response by Industrial Loads for Ancillary Services Provision

NASA Astrophysics Data System (ADS)

Zhang, Xiao

Demand response has gained significant attention in recent years as it demonstrates potentials to enhance the power system's operational flexibility in a cost-effective way. Industrial loads such as aluminum smelters, steel manufacturers, and cement plants demonstrate advantages in supporting power system operation through demand response programs, because of their intensive power consumption, already existing advanced monitoring and control infrastructure, and the strong economic incentive due to the high energy costs. In this thesis, we study approaches to efficiently integrate each of these types of manufacturing processes as demand response resources. The aluminum smelting process is able to change its power consumption both accurately and quickly by controlling the pots' DC voltage, without affecting the production quality. Hence, an aluminum smelter has both the motivation and the ability to participate in demand response. First, we focus on determining the optimal regulation capacity that such a manufacturing plant should provide. Next, we focus on determining its optimal bidding strategy in the day-ahead energy and ancillary services markets. Electric arc furnaces (EAFs) in steel manufacturing consume a large amount of electric energy. However, a steel plant can take advantage of time-based electricity prices by optimally arranging energy-consuming activities to avoid peak hours. We first propose scheduling methods that incorporate the EAFs' flexibilities to reduce the electricity cost. We then propose methods to make the computations more tractable. Finally, we extend the scheduling formulations to enable the provision of spinning reserve. Cement plants are able to quickly adjust their power consumption rate by switching on/off the crushers. However, switching on/off the loading units only achieves discrete power changes, which restricts the load from offering valuable ancillary services such as regulation and load following, as continuous power changes are required for these services. We propose methods that enable these services with the support of an on-site energy storage device. As demonstrated by the case studies, the proposed approaches are effective and can generate practical production instructions for the industrial loads. This thesis not only provides methods to enable demand response by industrial loads but also potentially encourages industrial loads to be active in electricity markets.

3D tooth microwear texture analysis in fishes as a test of dietary hypotheses of durophagy

NASA Astrophysics Data System (ADS)

Purnell, Mark A.; Darras, Laurent P. G.

2016-03-01

An understanding of how extinct animals functioned underpins our understanding of past evolutionary events, including adaptive radiations, and the role of functional innovation and adaptation as drivers of both micro- and macroevolution. Yet analysis of function in extinct animals is fraught with difficulty. Hypotheses that interpret molariform teeth in fishes as evidence of durophagous (shell-crushing) diets provide a good example of the particular problems inherent in the methods of functional morphology. This is because the assumed close coupling of form and function upon which the approach is based is weakened by, among other things, behavioural flexibility and the absence of a clear one to one relationship between structures and functions. Here we show that ISO 25178-2 standard parameters for surface texture, derived from analysis of worn surfaces of molariform teeth of fishes, vary significantly between species that differ in the amount of hard-shelled prey they consume. Two populations of the Sheepshead Seabream (Archosargus probatocephalus) were studied. This fish is not a dietary specialist, and one of the populations is known to consume more vegetation and less hard-shelled prey than the other; this is reflected in significant differences in their microwear textures. The Archosargus populations differ significantly in their microwear from the specialist shell-crusher Anarhichas lupus (the Atlantic Wolffish). Multivariate analysis of these three groups of fishes lends further support to the relationship between diet and tooth microwear, and provides robust validation of the approach. Application of the multivariate models derived from microwear texture in Archosargus and Anarhichas to a third fish species—the cichlid Astatoreochromis alluaudi—successfully separates wild caught fish that ate hard-shelled prey from lab-raised fish that did not. This cross-taxon validation demonstrates that quantitative analysis of tooth microwear texture can differentiate between fishes with different diets even when they range widely in size, habitat, and in the structure of their trophic apparatus. The approach thus has great potential as an additional tool for dietary analysis in extant fishes, and for testing dietary hypotheses in ancient and extinct species.

Kinetic study of ferronickel slag grinding at variation of ball filling and ratio of feed to grinding balls

NASA Astrophysics Data System (ADS)

Sanwani, Edy; Ikhwanto, Muhammad

2017-01-01

The objective of this paper is to investigate the effect of ball filling and ratio of feed to grinding balls on the kinetic of grinding of ferronickel slag in a laboratory scale ball mill. The experiments were started by crushing the ferronickel slag samples using a roll crusher to produce -3 mesh (-6.7 mm) product. This product, after sampling and sample dividing processes, was then used as feed for grinding process. The grinding was performed with variations of ball filling and ratio of feed to grinding balls for 150 minutes. At every certain time interval, particle size analysis was carried out on the grinding product. The results of the experiments were also used to develop linear regression model of the effect of grinding variables on the P80 of the product. Based on this study, it was shown that P80 values of the grinding products declined sharply until 70 minutes of grinding time due to the dominant mechanism of impact breakage and then decreased slowly after 70 minutes until 150 minutes of grinding time due to dominant mechanism of attrition breakage. Kinetics study of the grinding process on variations of grinding ball filling showed that the optimum rate of formation of fine particles for 20%, 30%, 40% and 50% mill volume was achieved at a particle size of 400 µm in which the best initial rate of formation occurred at 50% volume of mill. At the variations of ratio of feed to grinding balls it was shown that the optimum rate of grinding for the ratio of 1:10, 1: 8 and 1: 6 was achieved at a particle size of 400 µm and for the ratio of 1: 4 was at 841 µm in which the best initial rate of formation occurred at a 1:10 ratio. In this study, it was also produced two regression models that can predict the P80 value of the grinding product as a function of the variables of grinding time, ball filling and the ratio of the feed to grinding balls.

Engineering design and prototype development of a full scale ultrasound system for virgin olive oil by means of numerical and experimental analysis.

PubMed

Clodoveo, Maria Lisa; Moramarco, Vito; Paduano, Antonello; Sacchi, Raffaele; Di Palmo, Tiziana; Crupi, Pasquale; Corbo, Filomena; Pesce, Vito; Distaso, Elia; Tamburrano, Paolo; Amirante, Riccardo

2017-07-01

The aim of the virgin olive oil extraction process is mainly to obtain the best quality oil from fruits, by only applying mechanical actions while guaranteeing the highest overall efficiency. Currently, the mechanical methods used to extract virgin oils from olives are basically of two types: the discontinuous system (obsolete) and the continuous one. Anyway the system defined as "continuous" is composed of several steps which are not all completely continuous, due to the presence of the malaxer, a device that works in batch. The aim of the paper was to design, realize and test the first full scale sono-exchanger for the virgin olive oil industry, to be placed immediately after the crusher and before the malaxer. The innovative device is mainly composed of a triple concentric pipe heat exchanger combined with three ultrasound probes. This mechanical solution allows both the cell walls (which release the oil droplets) along with the minor compounds to be destroyed more effectively and the heat exchange between the olive paste and the process water to be accelerated. This strategy represents the first step towards the transformation of the malaxing step from a batch operation into a real continuous process, thus improving the working capacity of the industrial plants. Considering the heterogeneity of the olive paste, which is composed of different tissues, the design of the sono-exchanger required a thorough fluid dynamic analysis. The thermal effects of the sono-exchanger were monitored by measuring the temperature of the product at the inlet and the outlet of the device; in addition, the measurement of the pigments concentration in the product allowed monitoring the mechanical effects of the sono-exchanger. The effects of the innovative process were also evaluated in terms of extra virgin olive oil yields and quality, evaluating the main legal parameters, the polyphenol and tocopherol content. Moreover, the activity of the polyphenol oxidase enzyme in the olive paste was measured. Copyright © 2017 Elsevier B.V. All rights reserved.

PM4 crystalline silica emission factors and ambient concentrations at aggregate-producing sources in California.

PubMed

Richards, John R; Brozell, Todd T; Rea, Charles; Boraston, Geoff; Hayden, John

2009-11-01

The California Construction and Industrial Minerals Association and the National Stone, Sand, & Gravel Association have sponsored tests at three sand and gravel plants in California to compile crystalline silica emission factors for particulate matter (PM) of aerodynamic diameter of 4 microm or less (PM4) and ambient concentration data. This information is needed by industrial facilities to evaluate compliance with the Chronic Reference Exposure Level (REL) for ambient crystalline silica adopted in 2005 by the California Office of Environmental Health Hazard Assessment. The REL applies to PM4 respirable PM. Air Control Techniques, P.C. sampled for PM4 crystalline silica using a conventional sampler for PM of aerodynamic diameter of 2.5 microm or less (PM2.5), which met the requirements of 40 Code of Federal Regulations Part 50, Appendix L. The sample flow rate was adjusted to modify the 50% cut size to 4 microm instead of 2.5 microm. The filter was also changed to allow for crystalline silica analyses using National Institute for Occupational Safety and Health (NIOSH) Method 7500. The particle size-capture efficiency curve for the modified Appendix L instrument closely matched the performance curve of NIOSH Method 0600 for PM4 crystalline silica and provided a minimum detection limit well below the levels attainable with NIOSH Method 0600. The results of the tests indicate that PM4 crystalline silica emissions range from 0.000006 to 0.000110 lb/t for screening operations, tertiary crushers, and conveyor transfer points. The PM4 crystalline silica emission factors were proportional to the crystalline silica content of the material handled in the process equipment. Measured ambient concentrations ranged from 0 (below detectable limit) to 2.8 microg/m3. All values measured above 2 microg/m3 were at locations upwind of the facilities being tested. The ambient PM4 crystalline silica concentrations measured during this study were below the California REL of 3 microg/m3. The measured ambient concentrations in the PM4 size range are consistent with previously published ambient crystalline silica data applicable to the PM2.5 and PM of aerodynamic diameter of 10 microm or less (PM10) size ranges.

Tellurium Mobility Through Mine Environments

NASA Astrophysics Data System (ADS)

Dorsk, M.

2015-12-01

Tellurium is a rare metalloid that has received minimal research regarding environmental mobility. Observations of Tellurium mobility are mainly based on observations of related metalloids such as selenium and beryllium; yet little research has been done on specific Tellurium behavior. This laboratory work established the environmental controls that influence Tellurium mobility and chemical speciation in aqueous driven systems. Theoretical simulations show possible mobility of Te as Te(OH)3[+] at highly oxidizing and acidic conditions. Movement as TeO3[2-] under more basic conditions may also be possible in elevated Eh conditions. Mobility in reducing environments is theoretically not as likely. For a practical approach to investigate mobility conditions for Te, a site with known Tellurium content was chosen in Colorado. Composite samples were selected from the top, center and bottom of a tailings pile for elution experiments. These samples were disintegrated using a rock crusher and pulverized with an automated mortar and pestle. The material was then classified to 70 microns. A 10g sample split was digested in concentrated HNO3 and HF and analyzed by Atomic Absorption Spectroscopy to determine initial Te concentrations. Additional 10g splits from each location were subjected to elution in 100 mL of each of the following solutions; nitric acid to a pH of 1.0, sulfuric acid to a pH of 2.0, sodium hydroxide to a pH of 12, ammonium hydroxide to a pH of 10, a pine needle/soil tea from material within the vicinity of the collection site to a pH of 3.5 and lastly distilled water to serve as control with a pH of 7. Sulfuric acid was purposefully chosen to simulate acid mine drainage from the decomposition of pyrite within the mine tailings. Sample sub sets were also inundated with 10mL of a 3% hydrogen peroxide solution to induce oxidizing conditions. All collected eluates were then analyzed by atomic absorption spectroscopy (AAS) to measure Tellurium concentrations in each sample. The results provide a comparison of possible environmental Te mobility factors. While the process of bioavailability is not specifically addressed, preliminary data indicate a reference to perhaps assess impact to the local community and livestock relying on the San Miguel River, which is effected by run-off from the mine site.

Noise-based body-wave seismic tomography in an active underground mine.

NASA Astrophysics Data System (ADS)

Olivier, G.; Brenguier, F.; Campillo, M.; Lynch, R.; Roux, P.

2014-12-01

Over the last decade, ambient noise tomography has become increasingly popular to image the earth's upper crust. The seismic noise recorded in the earth's crust is dominated by surface waves emanating from the interaction of the ocean with the solid earth. These surface waves are low frequency in nature ( < 1 Hz) and not usable for imaging smaller structures associated with mining or oil and gas applications. The seismic noise recorded at higher frequencies are typically from anthropogenic sources, which are short lived, spatially unstable and not well suited for constructing seismic Green's functions between sensors with conventional cross-correlation methods. To examine the use of ambient noise tomography for smaller scale applications, continuous data were recorded for 5 months in an active underground mine in Sweden located more than 1km below surface with 18 high frequency seismic sensors. A wide variety of broadband (10 - 3000 Hz) seismic noise sources are present in an active underground mine ranging from drilling, scraping, trucks, ore crushers and ventilation fans. Some of these sources generate favorable seismic noise, while others are peaked in frequency and not usable. In this presentation, I will show that the noise generated by mining activity can be useful if periods of seismic noise are carefully selected. Although noise sources are not temporally stable and not evenly distributed around the sensor array, good estimates of the seismic Green's functions between sensors can be retrieved for a broad frequency range (20 - 400 Hz) when a selective stacking scheme is used. For frequencies below 100 Hz, the reconstructed Green's functions show clear body-wave arrivals for almost all of the 153 sensor pairs. The arrival times of these body-waves are picked and used to image the local velocity structure. The resulting 3-dimensional image shows a high velocity structure that overlaps with a known ore-body. The material properties of the ore-body differ from the host rock and is likely the cause of the observed high velocity structure. For frequencies above 200 Hz, the seismic waves are multiply scattered by the tunnels and excavations and used to determine the scattering properties of the medium. The results of this study should be useful for future imaging and exploration projects in mining and oil and gas industries.

Twelve actin-encoding cDNAs from the American lobster, Homarus americanus: cloning and tissue expression of eight skeletal muscle, one heart, and three cytoplasmic isoforms.

PubMed

Kim, Bo Kwang; Kim, Kyoung Sun; Oh, Chul-Woong; Mykles, Donald L; Lee, Sung Gu; Kim, Hak Jun; Kim, Hyun-Woo

2009-06-01

Lobster muscles express a diverse array of myofibrillar protein isoforms. Three fiber types (fast, slow-twitch or S1, and slow-tonic or S2) differ qualitatively and quantitatively in myosin heavy and light chains, troponin-T, -I, and -C, paramyosin, and tropomyosin variants. However, little is known about the diversity of actin isoforms present in crustacean tissues. In this report we characterized cDNAs that encode twelve actin isoforms in the American lobster, Homarus americanus: eight from skeletal muscle (Ha-ActinSK1-8), one from heart (Ha-ActinHT1), and three cytoplasmic type actins from hepatopancreas (Ha-ActinCT1-3). All twelve cDNAs were products of distinct genes, as indicated by differences in the 3'-untranslated regions (UTRs). The open reading frames specified polypeptides 376 or 377 amino acids in length. Although key amino residues are conserved in the lobster actins, variations in nearby sequences may affect actin polymerization and/or interactions with other myofibrillar proteins. Quantitative reverse transcription-polymerase chain reaction showed muscle fiber type- and tissue-specific expression patterns. Ha-Actin-HT1 was expressed exclusively in heart (87% of the total; 12% of the total was Ha-ActinCT1). Ha-ActinCT1 was expressed in all tissues, while CT2 and CT3 were expressed only in hepatopancreas, with Ha-ActinCT2 as the major isoform (93% of the total). Ha-ActinSK1 and SK2 were the major isoforms (88% and 12% of the total, respectively) in the S1 fibers of crusher claw closer muscle. Fast fibers in the cutter claw closer and deep abdominal muscles differed in SK isoforms. Ha-ActinSK3, SK4, and SK5 were the major isoforms in cutter claw closer muscle (12%, 48%, and 37% of the total, respectively). Ha-ActinSK5 and SK8 were the major isoforms in deep abdominal flexor (31% and 65% of the total, respectively) and extensor (46% and 53% of the total, respectively) muscles, with SK6 and SK7 expressed at low levels. These data indicate that fast fibers in cutter claw and abdominal muscles show a phenotypic plasticity with respect to the expression of actin isoforms and may constitute discrete subtypes that differ in contractile properties.

MASCOT: a new mass-spectrometer facility dedicated to the analysis of cosmogenic noble gases (3He and 21Ne) from terrestrial samples (Institute of Geological Sciences - University of Bern, Switzerland).

NASA Astrophysics Data System (ADS)

Delunel, Romain; Enderli, Patrick; Jenni, Hans-Erich; Leya, Ingo; Schlunegger, Fritz

2017-04-01

In the past years, terrestrial cosmogenic nuclides have been successfully used for dating exposure history of landforms and measuring erosional processes on Earth's surface. In this context, quantifications of landscape change have mainly been accomplished through the use of radioactive cosmogenic nuclides such as 10Be and 26Al, but their application has generally been restricted to Quaternary time scales because of their relatively short half-lives. The results are 10Be and 26Al concentrations that are below the detection limit of available accelerator mass spectrometers if the samples have a Late Miocene or even a Pliocene age. Contrariwise, cosmogenic noble gases such as 3He and 21Ne do not experience any radioactive decay through time, which places these isotopes in an unbeatable position for measuring paleo-denudation rates preserved in detrital material even if the ages of these deposits are up to 10 Ma and even older. These isotopes are thus keys for assessing the interplays between tectonic, climate and surface processes involved in the long-term evolution of mountain belts. Here we report the technical specifications of a noble gas analytical system that we have developed and set up at the Institute of Geological Sciences of the University of Bern, Switzerland, with the motivations to get dates and rates of erosion processes from the measurement of cosmogenic noble gases (3He and 21Ne) concentrations from terrestrial samples. This new facility, hosted at the Institute of Geological Sciences of the University of Bern, combines a MAP215-50 mass spectrometer fitted with a new high-sensitivity channel electron multiplier with an all-metal extraction and purification line. This later system thus comprises: (i) a double vacuum resistance furnace loaded by a 22-samples carrousel, (ii) three in-vacuo crushers (iii) an ultra high vacuum pumping system (<10-8 mbar) composed of turbo-molecular, ion-getter pumps and backed by a scroll pump, (iv) the line itself made up of a series of valves, connectors, a collection of getter-pellets filled fingers and activated charcoal cold-traps and (v) a dry-cryogen free cryostat system operating at temperatures ranging between 8K and 375K for trapping remaining heavy gases and focusing He and/or Ne before analysis in the mass spectrometer. This communication will be the opportunity to present our new noble gas system's full specifications together with an overview of the associated scientific questions we want to address using this new facility.

Triple-Quantum Filtered NMR Imaging of Sodium -23 in the Human Brain

NASA Astrophysics Data System (ADS)

Keltner, John Robinson

In the past multiple-quantum filtered imaging of biexponential relaxation sodium-23 nuclei in the human brain has been limited by low signal to noise ratios; this thesis demonstrates that such imaging is feasible when using a modified gradient-selected triple-quantum filter at a repetition time which maximizes the signal to noise ratio. Nuclear magnetic resonance imaging of biexponential relaxation sodium-23 (^{23}Na) nuclei in the human brain may be useful for detecting ischemia, cancer, and pathophysiology related to manic-depression. Multiple -quantum filters may be used to selectively image biexponential relaxation ^{23}Na signals since these filters suppress single-exponential relaxation ^{23}Na signals. In this thesis, the typical repetition times (200 -300 ms) used for in vivo multiple-quantum filtered ^{23}Na experiments are shown to be approximately 5 times greater than the optimal repetition time which maximizes multiple-quantum filtered SNR. Calculations and experimental verification show that the gradient-selected triple-quantum (GS3Q) filtered SNR for ^ {23}Na in a 4% agarose gel increases by a factor of two as the repetition time decreases from 300 ms to 55 ms. It is observed that a simple reduction of repetition time also increases spurious single-quantum signals from GS3Q filtered experiments. Irreducible superoperator calculations have been used to design a modified GS3Q filter which more effectively suppresses the spurious single-quantum signals. The modified GS3Q filter includes a preparatory crusher gradient and two-step-phase cycling. Using the modified GS3Q filter and a repetition time of 70 ms, a three dimensional triple-quantum filtered image of a phantom modelling ^{23} Na in the brain was obtained. The phantom consisted of two 4 cm diameter spheres inside of a 8.5 cm x 7 cm ellipsoid. The two spheres contained 0.012 and 0.024 M ^{23}Na in 4% agarose gel. Surrounding the spheres and inside the ellipsoid was 0.03 M aqueous ^{23}Na. The image dimensions were 16 x 16 x 16 voxels with the dimension of a voxel being 1.5 x 1.5 x 1.5 cm^3. The signal to noise ratio for the GS3Q filtered ^ {23}Na signal from the 0.012 and 0.024 M ^{23}Na spheres was 17 and 30 for a 54 minute experiment at 2.35 T. (Abstract shortened by UMI.).

Waves of the Future (for Mars): In-Situ Mid-infrared, Near-infrared, and Visible Spectroscopic Analysis of Antarctic Cryptoendolithic Communities.

NASA Astrophysics Data System (ADS)

Hand, K. P.; Calrson, R.; Sun, H.; Anderson, M.; Wynn, W.; Levy, R.

2005-12-01

We have analyzed both the surface expression and depth profile of cryptoendolithic microbial communities at Battleship Promontory, in the Dry Valleys of Antarctica. Data was collected on site with an active mid-infrared Fourier transform microspectrometer (2.6 - 15 um), a near-infrared spectrometer (0.9-1.8 um), and a visible spectrometer (0.4-1 um). The trio of instruments are connected to microscopes that yield ~1 mm2 spatial resolution on the sample and they are mounted on two perpendicular motorized stages that allow for spatial scanning over an area of ~2cm2. Here we present results on the surface expression of the subsurface microbes in these three spectral regions and we present results on the analysis of a colonized sample examined in cross section. The former case has direct application to the remote, robotic detection of life within the rocks of Mars and the later case provides fundamental insights into the geological and biological interactions that make the Antarctic cryptoendolithic ecosystems possible. Non-invasive surface detection of cyanobacterial dominated communities was possible through the observation of several distinct bands: the carbon-hydrogen stretching modes (symmetric and asymmetric) for CH, CH2, and CH3 in the regions of 3.3-3.6 um and 3.6-3.7 um; the NH2 scissoring and C=O stretch near 6.0 um; the amide I of beta-pleated structures at ~6.1 um; and the 6.4 um - 6.6 um bands of N-H in plane bend of the amide II functional group. In combination, these bands make a strong case for carbohydrates and proteins associated with life. Not surprisingly, as the integrity of the amorphous silica surface varnish improved, our ability to detected the subsurface biosignature decreased. We note, however, that by utilizing the JPL rock crusher in Antarctica, a device designed to fly on the Mars Science Laboratory mission, the mid-infrared biosignature was easily detected. In the cross-section analysis the mid-infrared data provide a depth profile tracking the presence of hydrocarbons, amide bonds, and the mineralogical transition from amorphous quartz to crystalline sandstone. Mapped onto this are the changes in the oxidation states of iron, as recorded by the visible and near-infrared spectrometers. Together, this data set allows us to track the role of biologically produced compounds, such as oxalic acid, in the chelation and leaching of iron compounds from the surface through the rock and into the deposition zone below the colonized subsurface region.

Interlaboratory comparison of mineral constituents in a sample from the Herrin (No. 6) coal bed from Illinois

USGS Publications Warehouse

Finkelman, Robert B.; Fiene, F.L.; Miller, R.N.; Simon, F.O.

1984-01-01

Approximately 20 kg of the Herrin (No. 6) coal was collected from a strip mine in St. Clair County, Ill. A 10-kg portion was ground to -60 mesh, homogenized, and riffled into 128 splits of 70-80 g each. Homogeneity of these splits was confirmed by moisture, ash, and sulfur analyses of six randomly selected splits. Results of these analyses were within the ASTM (American Society for Testing and Materials) guidelines for interlaboratory precision. Splits of the Herrin (No. 6) coal were then transmitted to more than 30 laboratories for analysis. Low-temperature plasma oxidation was used to isolate inorganic matter for quantitative chemical and mineralogical analysis. Despite a wide variation in ashing conditions, only minor variations in ash yields were obtained; these variations were attributed to differences in operating temperature and moisture content. Mineralogical analyses of low-temperature ash (LTA) concentrates prepared by five different laboratories indicated variations within the limits of analytical error. The mean values, in weight percent, for the major minerals are as follows: calcite, 9; quartz, 20; pyrite, 23; kaolinite, 14; and illite+mixed-layer clays, 31. Normative mineralogical calculations and Fourier transform infrared analysis (FTIR) yielded results similar to those obtained from X-ray diffraction (XRD). Choosing appropriate mineral standards was found to be critical for the proper use of analytical techniques such as XRD and FTIR. Good interlaboratory agreement was obtained for most major, minor, and trace elements despite differences in analytical procedures and in the type of sample analyzed (coal, high-temperature ash, or LTA). Discrepancies between analyses for zinc, strontium, manganese, and iron may be attributed to sampling inhomogeneity problems. Mossbauer spectroscopy showed that approximately 44 percent of the pyritic sulfur was lost through weathering in the first year after preparation of the interlaboratory sample. Szomolnokite and possibly coquimbite and jarosite were also identified. Scanning electron microscopy studies indicated ubiquitous pyrite framboids and, less commonly, euhedral crystals, skeletal grains, irregularly shaped particles, and vein fillings. Minor accessory minerals such as rare-earth phosphates and possibly silicates, zircon, barium sulfate, titanium oxide, and sphalerite were also found. The textural evidence indicates that the minerals in the banded material are detrital whereas the minerals occurring as vein and pore fillings are authigenic. Magnetic measurements indicate that coal crushed in a steel pulverizer is contaminated by small quantities of abrasion fragments from the crusher, which seriously affect the measured magnetic properties of the coal.

A REALLY WHEEZY WAY TO SAVE MONEY.

PubMed

Li, Grace; Almossawi, Ofran; Dulfeker, Hasna; Jones, Vicky; Taylor, Felicity

2016-09-01

To compare the palatability of oral non-soluble and oral soluble prednisolone tablets in paediatric patients admitted to the general paediatric wards in an acute London Trust. As part of ongoing quality improvement initiatives, the Paediatric and Pharmacy departments compared tolerability of soluble versus non-soluble prednisolone in a group of 27 patients. Using a modified 5 point hedonic scale with 'smiley' faces we measured palatability and tolerance (swallowed versus refusal or vomiting) over two three week periods: the first period whilst soluble prednisolone was dispensed (n=17) and the second period after the switch to non-soluble prednisolone had been made (n=10). All data were collected by doctors and nurses on the two paediatrics wards. We found acceptance of prednisolone to be similar before and after formulations were switched: 2 non-tolerated doses before (n=17) versus 3 non-tolerated doses after the switch (n=10).We found that 'disguising' the taste of the non-soluble prednisolone within a portion of sugar free jam, or mixed with 5 ml of sugar-free blackcurrant cordial, helped with acceptance, although both soluble and non-soluble formulations were frequently reported to be "Yuk"! The Trust has since made the switch to non-soluble prednisolone for all paediatric inpatients and for take home medications. An information leaflet has been developed for parents or carers to understand how to crush the prednisolone tablets. We have not had any parent or carer reported difficulty in preparing or administering the medication.Children under 15 account for 37.8% (20,510 of 54,300) of annual hospital admissions for acute asthma.1 A minimum course of 3 days' oral steroids are recommended in the BTS/SIGN 2014 guideline on the management of asthma.2 This acute Trust covers a population of over 300,000 in deprived boroughs of London.A typical three-day course of soluble prednisolone (at 2 mg/kg as per guidance, or approximately 20 mg) costs £20.88, compared to £2.48 for the equivalent dose of non-soluble prednisolone dispensed with a tablet crusher. Several hospital trusts have switched to using non-soluble prednisolone in order to achieve cost savings, but there have been anecdotal reports of poor palatability, raising concerns about compliance with taking medication once discharged.The switch from a soluble to a non-soluble formulation of prednisolone represents an annual saving of more than £44,000 for this hospital alone and, at scale, could realise substantial potential savings to the NHS, without compromising patients' clinical care. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Assessment and analysis of noise levels in and around Ib river coalfield, Orissa, India.

PubMed

Mohapatra, Haraprasad; Goswami, Shreerup

2012-05-01

Heavy earth moving machineries, different capacities of dumpers and loaders, blasting and drilling make the mining environment noisy. A study was carried out to assess the noise level in different opencast projects in and around Belpahar and Brajarajnagar areas of Ib river coalfield. Noise assessment was carried out in various residential, commercial and industrial places. The noise levels, especially L(eq) values of different wheel loaders, dumpers, shovel and crusher units were also assessed and were more than permissible limit (90dB) in some of their operating conditions. Sound ressure level measurements while drilling into coal and overburden at Lakhanpur opencast project yielded noise levels (L(eq)) of 81.33 to 96.2 dB. Thus, these L(eq) values of drilling machines in most of the operating conditions were above permissible limit. The average noise intensities (6 a.m.-10 p.m.: 51.6-60.875dB and 10 p.m.-6 a.m.: 42.6-49.8dB) and L(eq) values (6 a.m.-10 p.m.: 50.9-67.0dB and 10 p.m.-6 a.m.: 40.8-53.3dB) during both day and night time of the residential areas around the Ib river coalfield were in close proximity or beyond the permissible limit. The L(eq) values at some of the commercial and industrial places were beyond (6 a.m.-10 p.m.: 61.6-88.3 dB and 10 p.m.-6 a.m.: 55.4-64.8dB) permissible limit. However, in most of the cases, the L(max) noise values were more (6 a.m.-10 p.m.: 68.5-91.4 dB and 10 p.m.-6 a.m.: 69.3-76.4dB) than the permissible limit. Analysis of variance was also computed for heavy earth moving machineries in different operating conditions and also for different residential, commercial and industrial places to infer the level of significance. The difference of noise intensity produced by different wheel loaders at Lakhanpur and Lilari opencast projects, drilling machines at Lakhanpur opencast project, 50 tons capacity dumpers at various conditions of Ib river coalfield within the same operating condition was significant at both 5% and 1% levels of significance. Similarly, the variance of estimated noise level in residential places during day time and commercial and industrial places during day and night time was significant at both 5% and 1% levels of significance. Moreover, a preliminary survey adopting questionnaire method amongst the mine workers and local inhabitants was also carried out to evaluate their perception about the mining related noise.

Animal left-right asymmetry.

PubMed

Blum, Martin; Ott, Tim

2018-04-02

Symmetry is appealing, be it in architecture, art or facial expression, where symmetry is a key feature to finding someone attractive or not. Yet, asymmetries are widespread in nature, not as an erroneous deviation from the norm but as a way to adapt to the prevailing environmental conditions at a time. Asymmetries in many cases are actively selected for: they might well have increased the evolutionary fitness of a species. Even many single-celled organisms are built asymmetrically, such as the pear-shaped ciliate Paramecium, which may depend on its asymmetry to navigate towards the oxygen-richer surface of turbid waters, at least based on modeling. Everybody knows the lobster with its asymmetric pair of claws, the large crusher usually on the left and the smaller cutter on the right. Snail shells coil asymmetrically, as do the organs they house. Organ asymmetries are found throughout the animal kingdom, referring to asymmetric positioning, asymmetric morphology or both, with the vertebrate heart being an example for the latter. Functional asymmetries, such as that of the human brain with its localization of the language center in one hemisphere, add to the complexity of organ asymmetries and presumably played a decisive role for sociocultural evolution. The evolutionary origin of organ asymmetries may have been a longer than body length gut, which allows efficient retrieval of nutrients, and the need to stow a long gut in the body cavity in an orderly manner that ensures optimal functioning. Vertebrate organ asymmetries (situs solitus) are quite sophisticated: in humans, the apex of the asymmetrically built heart points to the left; the lung in turn, due to space restrictions, has fewer lobes on the left than on the right side (two versus three in humans), stomach and spleen are found on the left, the liver on the right, and small and large intestine coil in a chiral manner (Figure 1A). In very rare cases (1:10,000), the organ situs is inverted (situs inversus), while heterotaxia refers to another rare situation (about 1:1,000), in which subsets of organs show normal or aberrant positioning or morphology (Figure 1B). Individuals with situs solitus or situs inversus are healthy, whereas heterotaxia presents severe congenital malformations. Many human syndromes are known in which patients suffer from laterality defects, such as Katagener syndrome, in which the organ situs is inverted in one half of patients and males are sterile. Snail shells and vertebrate organs are examples of biased asymmetries with on average only one inversion in every 10,000 cases. Other asymmetries such as the coiling of the tails of piglets occur randomly with a 50:50 distribution. This primer exclusively deals with organ asymmetries in the animal kingdom, specifically with the mechanisms that ensure the development of biased asymmetries during embryogenesis. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparison of mounting methods for the evaluation of fibers by phase contrast microscopy.

PubMed

Lee, Eun Gyung; Pang, Thomas W S; Nelson, John; Andrew, Mike; Harper, Martin

2011-07-01

The objectives of this study were to evaluate mounting methods for fiber examination of air sample filters by phase contrast microscopy (PCM) and to evaluate differences in fiber counts that might be due to fiber movement. Acetone/triacetin (AT) with various amounts of triacetin and acetone/Euparal (AE) where the mounting medium was placed between the cleared filter wedge and the coverslip were tested as a function of time. Field sample slides collected from a taconite iron-ore processing mill, a tremolitic talc-ore processing mill, and from around a crusher in a meta-basalt stone quarry were prepared with relocatable coverslips to revisit the same field areas on the slides. For each slide, three or four field areas were randomly selected and pictures were taken every 2 weeks to determine any sign of fiber movement over time. For 11 AT slides (named as AT-3.5) prepared with 3.5 μl of the mounting medium according to the NIOSH 7400 method, no fiber movements were detected over 59 weeks. On the other hand, AT slides prepared with larger quantities (10, 15, and 20 μl) of the mounting medium (named as AT-10) and AE slides prepared with ∼10 μl mounting medium showed fiber movement from the eighth day at the earliest. Fiber movement began earlier for the slides mounted with excess triacetin than for those mounted with Euparal. The sample slide storage method, either vertically or horizontally, did not seem to accelerate fiber movement. Additionally, two other modified methods, dimethylformamide solution/Euparal (mDE) and dimethylformamide solution/triacetin (mDT), were also prepared where the mounting medium was placed between the cleared filter wedge and the glass slide. The findings of fiber movements were similar; when 3.5 μl of triacetin was used for the mDT slides, fiber movements were not detected, while fibers on slides prepared with 10 μl triacetin (mDT-10) moved around. No fiber movements were observed for the mDE slides at any time during 59 weeks. Once fiber movement started, fibers moved over distances measured from 4 μm and up to >1000 μm within 22 weeks. However, since then, no further fiber movements have been observed in any field sample slides. Additional sample slides, two Amosite and two chrysotile, were prepared from Union for International Cancer Control (UICC) samples using the AT method with 5 μl triacetin mounting medium. Fiber movements were also observed in these samples; chrysotile fibers began to migrate in 3 weeks, while Amosite fiber movement started after 3 months. Although fiber movement was observed for the AT-10, AE, and mDT-10 sample slides, fiber counts were not significantly different from AT-3.5 and mDE samples that exhibited no fiber movement. Although fiber counts would not be significantly changed by fiber movement, the type and amount of mounting medium for sample slide preparation remains critical for issues such as quality assurance and training of analysts by revisiting the same fibers.

Reflection seismic characterization of the Grängesberg iron deposit and its mining-induced structures, central Sweden

NASA Astrophysics Data System (ADS)

Place, Joachim; Malehmir, Alireza; Högdahl, Karin; Juhlin, Christopher; Persson Nilsson, Katarina

2014-05-01

Reflection seismic investigation has been conducted on the Grängesberg apatite iron deposit where over 150 Mt of iron ore were produced until the mine closed in 1989. The mine infrastructure with shafts and tunnels extend down to ca. 650 m below the surface. Both natural and mine induced fracture and fault systems are today water-filled (some of them extending to the surface). The disputed ore genesis of the apatite-iron ores and its exploration potential due to large remaining quantities once again attracts both scientific and commercial interests. A good understanding of the geometry of mineral deposits and their hostrock structures at depth is essential for optimizing their exploration and exploitation. In addition, deep understanding of the fracture system is vital if mining activity is resumed as these may impact the terrain stability and seismicity, which may put at risk new populated and industrial areas. To address some of these challenging issues related to the past mining and also to obtain information about the depth continuation of the existing deposit, two E-W oriented reflection lines with a total length of 3.5 km were acquired in May 2013 by Uppsala University. A weight drop mounted on an hydraulic bobcat truck (traditionally used for concrete breaking in demolition sector) was used to generate seismic signal. In order to increase the signal-to-noise ratio, several impacts were generated at each shot point and stacked together. The seismic lines intersect at high angle the Grängesberg ore body and open pit, as well as several mining-induced faults. A combination of cabled and wireless receivers placed at every 10 m was used for the data recording. Use of wireless receivers was necessary as deploying cabled sensors was not possible due to city infrastructures, roads and houses. A careful analysis of the data suggested that several field-related issues such as (1) the crooked geometry of the lines (due to the available path and road network), (2) electric and vibration noise due to populated areas and roads, as well as a rock crusher working close to the line, (3) significant static variations (due to the variable nature of the terrain: forest, roads, open pit filled with 10s of meters of unconsolidated materials...), make this dataset similar to a city-kind dataset. Preprocessing of the data first required the cable- and wireless- recorded sub-datasets to be merged using GPS time stamps (nanoseconds accuracy) registered in the active data. Vertical shift and stack was then carried out to stack all data available at each shot point. Preliminary results from brute stacks exhibit evidences of reflections or diffractions. It is anticipated that further processing, involving especially appropriate static corrections and velocity analysis, would help interpreting such seismic events in relation to the ore body and its surrounding structures. Possible along-profile compartmentalization is also detected; further processing is however necessary before interpreting such features in terms of recent faulting. Acknowledgements: Formas, Grängesberg Iron AB, Spendrups and Geological Survey of Sweden

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raj K. Rajamani; Jose Angel Delgadillo

A research team from the University of Utah is working to make inroads into saving energy in these SAG mills. In 2003, Industries of the Future Program of the Department of Energy tasked the University of Utah team to build a partnership between the University and the mining industry for the specific purpose of reducing energy consumption in SAG mills. A partnership was formed with Cortez Gold Mines, Kennecott Utah Copper Corporation, Process Engineering Resources Inc. and Outokumpu Technology. In the current project, Cortez Gold Mines played a key role in facilitating the 26-ft SAG mill at Cortez as amore » test mill for this study. According to plant personnel, there were a number of unscheduled shut downs to repair broken liners and the mill throughput fluctuated depending on ore type. The University team had two softwares, Millsoft and FlowMod to tackle the problem. Millsoft is capable of simulating the motion of charge in the mill. FlowMod calculates the slurry flow through the grate and pulp lifters. Based on this data the two models were fine-tuned to fit the Cortez SAG will. In the summer of 2004 a new design of shell lifters were presented to Cortez and in September 2004 these lifters were installed in the SAG mill. By December 2004 Cortez Mines realized that the SAG mill is drawing approximately 236-kW less power than before while maintaining the same level of production. In the first month there was extreme cycling and operators had to learn more. Now the power consumption is 0.3-1.3 kWh/ton lower than before. The actual SAG mill power draw is 230-370 kW lower. Mill runs 1 rpm lesser in speed on the average. The recirculation to the cone crusher is reduced by 1-10%, which means more efficient grinding of critical size material is taking place in the mill. All of the savings have resulted in reduction of operating cost be about $0.023-$0.048/ ton. After completing the shell lifter design, the pulp lifter design was taken up. Through a series of mill surveys and model calculations it was figured that the radial pulp lifter installed on the mill had less than optimum discharge capacity. A number of alternative designs were evaluated. The final choice was the Turbo Pulp Lifter for which Outukumpu Technology, Centennial, Colorado had filed a patent. After installation of the pulp lifter a 22% increase in throughput rate from 344 stph to 421 stph was realized. A 35% decrease in the SAG mill power draw from 3,908 HP to 2,526 HP (2,915 kW to 1,884 kW) was recorded. This equates to a 47% decrease in SAG unit energy consumption from 8.98 kWh/ton to 4.74 kWh/ton. A 11% decrease in SAG mill speed was observed indicating optimized ball strikes. Also, the ball chip generation from the SAG mill was reduced considerably. Further more, a 7% decrease in ball mill power draw from 4,843 HP to 4,491 HP (3,613 kW to 3,350 kW) was observed. This equates to a 24% decrease in ball mill unit energy consumption from 11.13 kWh/ton to 8.43 kWh/ton.« less

COIN Project: Towards a zero-waste technology for concrete aggregate production in Norway

NASA Astrophysics Data System (ADS)

Cepuritis, Rolands; Willy Danielsen, Svein

2014-05-01

COIN Project: Towards a zero-waste technology for concrete aggregate production in Norway Rolands Cepuritis, Norcem/NTNU and Svein Willy Danielsen, SINTEF Aggregate production is a mining operation where no purification of the "ore" is necessary. Still it is extremely rare that an aggregate production plant is operating on the basis of zero-waste concept. This is since historically the fine crushed aggregate (particles with a size of less than 2, 4 or sometimes 8 mm) has been regarded as a by-product or waste of the more valuable coarse aggregate production. The reason is that the crushed coarse aggregates can easily replace coarse rounded natural stones in almost any concrete composition; while, the situation with the sand is different. The production of coarse aggregate normally yields fine fractions with rough surface texture, flaky or elongated particles an inadequate gradation. When such a material replaces smooth and rounded natural sand grains in a concrete mix, the result is usually poor and much more water and cement has to be used to achieve adequate concrete flow. The consequences are huge stockpiles of the crushed fine fractions that can't be sold (mass balance problems) for the aggregate producers, sustainability problems for the whole industry and environmental issues for society due to dumping and storing of the fine co-generated material. There have been attempts of utilising the material in concrete before; however, they have mostly ended up in failure. There have been attempts to adjust the crushed sand to the properties of the natural sand, which would still give a lot of waste, especially if the grading would have to be adjusted and the high amounts of fines abundantly present in the crushed sand would have to be removed. Another fundamental reason for failure has been that historically such attempts have mainly ended up in a research carried out by people (both industrial and academic) with aggregate background (= parties willing to find market for their crusher fines) providing only conclusions already well known by the engineers involved in concrete production. Due to the pressing situation with the left resources of the natural sand and gravel in Scandinavia, a new and different development approach has been recently attempted with the Concrete Innovation Center (COIN) in Norway. The centre is a research based innovation project that has brought together and served as a source of funding to facilitate the crucial interaction between the professionals from the different involved industries (quarrying machinery supplier, aggregate producers, concrete producers and concrete contractors) and the academic people from universities and research institutions, in order come up with a better crushed sand solution for the future. The concept under development has been a zero-waste technology for aggregate production, where instead of reducing the amount of the crushed fines their properties are rather engineered to crucially increase the overall performance of the sand in concrete. The project also involves collaboration with a state-of-the-art aggregate production plant where the new technology has already been implemented. The production process there is based on the new engineered sand concepts successfully supplying 100% all of the produced fractions to concrete and asphalt producers.

COMPARISON OF HYDROCORTISONE 10 MG TABLETS: TABLET HARDNESS OPTIMISED FOR ADULT USE HAS NEGATIVE CONSEQUENCES FOR PAEDIATRIC USE.

PubMed

Saimbi, Sarina; Madden, Valerie; Stirling, Heather; Yahyouche, Asma; Batchelor, Hannah

2016-09-01

Children's medicines are not always readily available as an age appropriate product and manipulation of adult products is often required. Recently the commercial manufacturing process for 10 mg hydrocortisone tablets has changed and the compression force increased due to tablets fracturing on removal from the blister pack. However, this change led to parents of children requiring hydrocortisone reporting that the tablets were more difficult to manipulate.This study evaluated 10 mg hydrocortisone tablets for their suitability for manipulation in order to deliver an appropriate dose to children (2 mg dose). The physical properties of tablets with the old and new compression force were compared as well as the accuracy of obtaining the paediatric dose. The tablets compared were hydrocortisone Auden 10 mg tablets (Brand A, PL16876/002)-these are the newer, harder tablets- and hydrocortisone 10 mg tablets (Brand B, PL17507/0097). Tablet physical properties including friability (Copley FRV200) and tablet hardness (Copley TBF1000) were compared. The accuracy of split doses (halve and quarter tablets) were recorded on a Sartorius analytical balance. The accuracy of the 2 mg paediatric dosing was assessed by crushing the tablet, adding 10 mL of water and extracting 2 mL. The concentration was measured using UV analysis (Jenway Genova Plus) according to a calibration curve (wavelength=246 nm). Two devices were used to crush the tablets: a spoon onto a plate and a commercially available crushing device (Apothecary Ezy Crush Pill Crusher With Ergo Grip). As anticipated Brand A tablets were harder (51.85 ±5.1 N) compared to Brand B (30.99±4.1 N). Brand A tablets passed the friability testing with <1% weight loss whereas Brand B failed as 5 tablets broke during testing.The accuracy of split doses using the score lines to halve and quarter the tablets showed that Brand A were generally better with smaller ranges for both halves (Range for A=41-55%; B=29-70%) and quarters (Range for A=17-35%; B=12-42%) compared to Brand B.The 2 mg dosing accuracy was better for Brand B tablets compared to A and crushing tablets using a commercial device improved the accuracy of dosing for both brands of tablets. When crushing using a spoon the mean dose obtained was 1.3 mg for Brand A and 1.7 mg for Brand B; the commercial crushing device gave values of 1.9 mg for Brand A and 2.1 mg for Brand B. Parents or carers who are required to manipulate 10 mg hydrocortisone tablets to administer a dose to children dispersed in water should be advised to crush the tablet into a fine powder where possible to improve the likelihood of administering an accurate dose. This is particularly important since the introduction of new hydrocortisone Auden tablets which are known to be harder tablets and therefore more force is required to crush these. Some of the experimental work within this project was conducted by Andrew Hackett and Kameron Paul-Thaper whilst at the University of Birmingham on work experience from Arden Sixth Form, Station Rd, Knowle, Solihull, West Midlands, B93 0PT. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Final Technical Report: Intensive Quenching Technology for Heat Treating and Forging Industries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aronov, Michael A.

2005-12-21

Intensive quenching (IQ) process is an alternative way of hardening (quenching) steel parts through the use of highly agitated water and then still air. It was developed by IQ Technologies, Inc. (IQT) of Akron, Ohio. While conventional quenching is usually performed in environmentally unfriendly oil or water/polymer solutions, the IQ process uses highly agitated environmentally friendly water or low concentration water/mineral salt solutions. The IQ method is characterized by extremely high cooling rates of steel parts. In contrast to conventional quenching, where parts cool down to the quenchant temperature and usually have tensile or neutral residual surface stresses at themore » end of quenching. The IQ process is interrupted when the part core is still hot and when there are maximum compressive stresses deep into the parts, thereby providing hard, ductile, better wear resistant parts. The project goal was to advance the patented IQ process from feasibility to commercialization in the heat-treating and forging industries to reduce significantly energy consumption and environmental impact, to increase productivity and to enhance economic competitiveness of these industries as well as Steel, Metal Casting and Mining industries. To introduce successfully the IQ technology in the U.S. metal working industry, the project team has completed the following work over the course of this project: A total of 33 manufacturers of steel products provided steel parts for IQ trails. IQT conducted IQ demonstrations for 34 different steel parts. Our customers tested intensively quenched parts in actual field conditions to evaluate the product service life and performance improvement. The data obtained from the field showed the following: Service life (number of holes punched) of cold-work punches (provided by EHT customer and made of S5 shock-resisting steel) was improved by two to eight times. Aluminum extrusion dies provided by GAM and made of hot work H-13 steel outperformed the standard dies by at least 50%. Dies provided by an AST customer, made of plain carbon 1045 steel and used for pellet manufacturing outperformed the standard dies by more than 100%. Concrete crusher liner wear plates provided by an EHT customer and made of 1045 steel, had the same surface hardness as the plates made of more expensive, pre-hardened high alloy HARDOX-500 material supplied by a Swedish company and used currently by the EHT customer. The 1045 material intensively quenched wear plates are currently in the field. Concrete block molding machine wear plates provided by an IQT customer and made of 8620 steel were processed at the AST production IQ system using a 40% reduced carburization cycle. An effective case depth in the intensively quenched wear plates was the same as in the standard, oil quenched parts. Base keys provided by an EHT customer and made of 8620 steel were processed using a 40% reduced carburization cycle. The intensively quenched parts showed the same performance as standard parts. IQT introduced the IQ process in heat treat practices of three commercial heat-treating shops: Akron Steel Treating Co., Summit Heat Treating Co. and Euclid Heat Treating Co. CWRU conducted a material characterization study for a variety of steels to develop a database to support changing/modification of recognized standards for quenching steel parts. IQT conducted a series of IQ workshops, published seven technical papers and participated in ASM Heat Treating Society conference and exposition and in Furnace North America Show. IQT designed and built a fully automated new IQ system installed at the Center for Intensive Quenching. This system includes the following major components: a stand-alone 1,900-gallon IQ water system, a 24'' x 24'' atmosphere pit furnace, and an automated load transfer mechanism. IQT established a ''Center for Intensive Quenching'' at the AST facilities. The 4,000 square feet Center includes the following equipment: High-velocity single part quenching IQ unit developed and built previously under EMTEC CT-65 project. The unit is equipped with a neutral salt bath furnace and a high-temperature, electric-fired, atmosphere, box furnace. New 1,900 gallon IQ system with a 24'' x 24'' atmosphere pit furnace and a load transfer mechanism. Shaker hearth furnace equipped with an IQ water tank and with a chiller to maintain the required water temperature. Potential Savings for USA Heat Treating Industry IQ Process Benefit/Annual Benefit for USA Heat Treating Industry Full elimination or 30% reduction of the carburization cycle Savings of 1,800 billion Btu of energy Cost reduction by $600,000,000 Reduction of CO2 emissions by 148,000 ton Part weight reduction by 5% Savings in material cost of $70,000,000 Savings of 300 billion Btu of energy« less

Simulation-Assisted Evaluation of Grinding Circuit Flowsheet Design Alternatives: Aghdarreh Gold Ore Processing Plant / Ocena Alternatywnych Schematów Technologicznych Procesu Rozdrabniania W Zakładach Przeróbki Rud Złota W Aghdarreh, Z Wykorzystaniem Metod Symulacji

NASA Astrophysics Data System (ADS)

Farzanegan, A.; Ghalaei, A. Ebtedaei

2015-03-01

The run of mine ore from Aghdarreh gold mine must be comminuted to achieve the desired degree of liberation of gold particles. Currently, comminution circuits include a single-stage crushing using a jaw crusher and a single-stage grinding using a Semi-Autogenous Grinding (SAG) mill in closed circuit with a hydrocyclone package. The gold extraction is done by leaching process using cyanidation method through a series of stirred tanks. In this research, an optimization study of Aghdarreh plant grinding circuit performance was done to lower the product particle size (P80) from 70 μm to approximately 40 μm by maintaining current throughput using modeling and simulation approach. After two sampling campaigns from grinding circuit, particle size distribution data were balanced using NorBal software. The first and second data sets obtained from the two sampling campaigns were used to calibrate necessary models and validate them prior to performing simulation trials using MODSIM software. Computer simulations were performed to assess performance of two proposed new circuit flowsheets. The first proposed flowsheet consists of existing SAG mill circuit and a new proposed ball mill in closed circuit with a new second hydrocyclone package. The second proposed flowsheet consists of existing SAG mill circuit followed by a new proposed ball mill in closed circuit with the existing hydrocyclone package. In all simulations, SAGT, CYCL and MILL models were selected to simulate SAG mill, Hydrocyclone packages and ball mill units. SAGT and MILL models both are based on population balance model of grinding process. CYCL model is based on Plitt's empirical model of classification process in hydrocyclone units. It was shown that P80 can be reduced to about 40 μm and 42 μm for the first and second proposed circuits, respectively. Based on capital and operational costs, it can be concluded that the second proposed circuit is a more suitable option for plant grinding flowsheet modification. Surowy urobek z kopalni rud złota Aghdarreh musi najpierw zostać poddany rozdrobnieniu, aby zapewnić efektywniejsze uwalnianie cząsteczek złota. W chwili obecnej obiegi rozdrabniania obejmują kruszenie jednostopniowe z wykorzystaniem kruszarek szczękowych oraz kruszenie jednostopniowe z użyciem kruszarek półautomatycznych w obiegu zamkniętym z hydrocyklonem. Odzysk złota odbywa się przy zastosowaniu procesu ługowania, z zastosowaniem metody cyjankowej w szeregu mieszalników. W pracy tej przeprowadzono optymalizację procesu rozdrabniania rud w zakładach przeróbczych Aghdarreh prowadzonego w celu zmniejszenia rozmiarów uzyskiwanych cząsteczek złota (Ps0) z 70 μm do ok. 40 μm poprzez zapewnienie ciągłości procesu, z wykorzystaniem metod modelowania i symulacji. Na podstawie dwóch zestawów próbek z ciągu technologicznego rozdrabniania, rozkłady wielkości cząstek zostały statystycznie zrównoważone z wykorzystaniem oprogramowania NorBal. Pierwszy i drugi zbiór danych otrzymanych na podstawie dwóch zestawów próbek wykorzystany został do kalibracji i walidacji modeli, przed przystąpieniem do właściwych badań symulacyjnych z użyciem oprogramowania MODSIM. Symulacje komputerowe przeprowadzono w celu oceny wydajności dwóch proponowanych ciągów technologicznych. Pierwszy ciąg obejmuje istniejące kruszarki półautomatyczne i nowo proponowaną kruszarkę kulową pracującą w obiegu zamkniętym z hydrocyklonem. Drugi rozważany ciąg stanowi istniejąca kruszarka półautomatyczna, następnie proponowana kruszarka kulowa pracująca w obiegu zamkniętym z istniejącym hydrocyklonem. We wszystkich symulacjach bazowano na modelach SAGT, CYCL i MILL do symulacji pracy kruszarek półautomatycznych, pakietu hydrocyklonu oraz pojedynczych kruszarek. Modele SAGT i MILL oparte są na modelu zrównoważonej populacji w procesie rozdrabniania. Model CYCL opiera się na empirycznym modelu klasyfikacji Plitta zastosowanym do hydrocyklonów. Wykazano, że rozmiar cząstek zmniejszony został odpowiednio do 40 μm i 42 μm dla pierwszego i drugiego analizowanego obiegu. Uwzględniając nakłady kapitałowe oraz koszty operacyjne, wyciągnąć można więc wniosek, ze drugi proponowany układ jest korzystniejszą opcją modyfikacji istniejącego ciągu technologicznego rozdrabniania.

On the actual variety of plate dynamical mechanisms and how mantle evolution affected them through time, from core formation to the Indian collision

NASA Astrophysics Data System (ADS)

Osmaston, Miles

2010-05-01

If horizontal plate motions were driven by thermal convection of the mantle, they would display the action of slow-to-change body forces. Yet rapid changes of spreading rate and direction, and ridge jumps, are well-documented for the past 130Ma. Also convection cannot readily cause rotations of a plate (e.g. Africa) about a pole within the plate or near it. And plate motions, especially that of India, scarcely fit a convective pattern. To address these problems we look first at mantle motivation at both ends of earth history, beginning with core formation. I then introduce 3 important properties of mantle materials, whose neglect by mantle modellers has surely impaired the value of their work, but whose recognition illuminates the present plate dynamical situation and provides the Earth with a heat engine that is not thermal convection. Finally I sketch the intervening changes in behaviour over time, the sharpest of which brought about the rise of atmospheric oxygen at ~2.25Ga. Core formation. As the very high specific angular momentum of mean planetary material (>105-fold relative to solar) can only be achieved if the planets were wholly accreted in presence of the nebula [1], the iron percolation model is ruled out, because it takes too long. This validates the A.E.Ringwood model (1960-1978) involving nebular H reaction with erupting FeO. The iron then loads the downgoing limb of what is then not a truly thermal convection system. Huge volumes of reaction water were produced, giving the early Earth a wet mantle, a (diminishing) feature that we'll see has constrained mantle behaviour ever since. Plate dynamics since 150Ma. Multiple plate dynamical evidence [2], which will be rapidly re-presented here, shows that currently (a) the Earth has a 2-layer mantle system with a boundary at ~660km and (b) that most cratons have tectospheric keels that reach right to that boundary, or nearly so. The argument is the simple and persuasive one (even to seismologists) of mantle volume disposal if two such cratons approach one another (e.g. Caucasus), and of the provision of mantle volume to put under the growing ocean if they separate, e.g. S Atlantic, Arctic opening. In the latter case, W Siberia offers a major gap between the Russian and Angara keels and it is through this gap that Arctic-bound upper mantle flow is seen to have acted on India's cratonic keel and caused its powerful collision with Asia, rejuvenating many intervening ranges. This has 'put Asia in a crusher' and is contrary to the plate tectonics dictum of plate boundary interaction. Manifesting this 'suction' upon the Indian keel there is around S India by far the deepest dent in the geoid. The 3 neglected mantle properties we need for understanding this behaviour are:- (1) The garnet-to-spinel peridotite phase change, typically occurring at 70-90km depth, converts one joule into ~50 times more volume increase than simple expansion and does so with the big force of solid-state recrystallization. The density drop across the phase change can approximate that of simply heating the rock through ~1000K so it should never have been neglected by modellers. (2) Interstitial melt has much lower thermal conductivity than its parent solid, so overall thermal conductivity is reduced by >10% per 1% of non-migrating melt, i.e. by ~30% for typical oceanic LVZ conditions. (3) If the water-weakening of the mantle mineral structure (in the form of dislocations by H atoms) is not too high, that weakening will be stripped out by partitioning into any interstitial melt that is present, stiffening the rock by up to 2 orders of magnitude [3]. This contradicts the precept of seismologists and mantle modellers that lowered seismic Vs automatically signifies asthenospheric mobility. Since Vp-Vs relationships in the oceanic LVZ and at >180km under cratons are closely similar, the recognition of (3) explains both the dynamically evident strength of cratonic deep keels and offers a new basis for modelling the MOR process. Instead of convectively driven divergent mantle flow, this has a deeply extending laterally accreting narrow (20cm?) mantle crack below the axis and the gt-sp peridotite phase change (1) is present in the walls at some level. Heat from an eruption up the crack causes a lot of extra volume increase in the walls at that level, which closes the crack and wedges the plates apart with great force. This push-apart is responsible both for MOR rift valleys above and for inducing more mantle into the crack from below. It is this 'suction' which appears responsible for the above-mentioned plate dynamical behaviour and for the geoid dent around India. This MOR mechanism is a powerful heat engine but it is not convection. That cratonic keels may 'rub' on the highly viscous lower mantle at the 660 offers a means of coupling polar core-to-mantle electromagnetic coupling torque to the plate system and thereby to provide rotations. Probable examples are the clockwise rotation of Antarctica since Tierra del Fuego was extracted (150Ma?) from the Weddell Sea, the linked CCW rotation of Africa, and other geomag-related changes of plate motion [4]. From an Earth history perspective, it appears that during the Archaean the mantle was wet enough for vigorous whole-mantle convection to remove the early radiogenic heating. But, as this waned and the evolution of ocean water reduced the water-weakening, the lock-up condition prescribed in (3) was reached soon after 2.5Ga, and plate tectonics halted for ~230Ma, before restarting in the present 2-layer mode. The collapse of MORs during this hiatus correlates with major geological and atmospheric changes including the primary rise in oxygen to which we owe our existence [2]. [1] Osmaston MF (2009) A two-stage scenario for forming the Sun's planetary system, with good links to exoplanet findings, arising from new physical insight on the gravitational process. EPSC Abstracts 4, EPSC2009-264, European Planetary Science Congress, Potsdam 2009. [2] Osmaston MF (2009) Deep cratonic keels and a 2-layer mantle? Tectonic basis for some far-reaching new insights on the dynamical properties of the Earth's mantle: example motions from Mediterranean, Atlantic-Arctic and India. Geophys.Res.Abstr. 11, EGU2009-6359-6, EGU Gen. Assy 2009. [3] Hirth, G & Kohlstedt, DL (1996) Water in the oceanic upper mantle: implication for rheology, melt extraction, and the evolution of the lithosphere, EPSL 144, 93-108. [4] Osmaston, M. F. (2003) What drives plate tectonics? Slab pull, ridge push or geomagnetic torque from the CMB? A new look at the old players vis-a-vis an exciting new one. XXIII IUGG 2003, Sapporo, Japan. Abstracts CD, p. B129, Abstr #016795-2.