Durability of hardboard siding

Treesearch

Anton TenWolde; Charles Carll

2004-01-01

In response to concerns about hardboard siding failures, a study was performed to assess if performance in a current hardboard industry quality assurance test procedure correlated with in-service performance and how well this performance might be predicted by use of alternative or additional test procedures. A variety of laboratory tests were performed on a large...

Defense Waste Processing Facility Canister Closure Weld Current Validation Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korinko, P. S.; Maxwell, D. N.

Two closure welds on filled Defense Waste Processing Facility (DWPF) canisters failed to be within the acceptance criteria in the DWPF operating procedure SW4-15.80-2.3 (1). In one case, the weld heat setting was inadvertently provided to the canister at the value used for test welds (i.e., 72%) and this oversight produced a weld at a current of nominally 210 kA compared to the operating procedure range (i.e., 82%) of 240 kA to 263 kA. The second weld appeared to experience an instrumentation and data acquisition upset. The current for this weld was reported as 191 kA. Review of the datamore » from the Data Acquisition System (DAS) indicated that three of the four current legs were reading the expected values, approximately 62 kA each, and the fourth leg read zero current. Since there is no feasible way by further examination of the process data to ascertain if this weld was actually welded at either the target current or the lower current, a test plan was executed to provide assurance that these Nonconforming Welds (NCWs) meet the requirements for strength and leak tightness. Acceptance of the welds is based on evaluation of Test Nozzle Welds (TNW) made specifically for comparison. The TNW were nondestructively and destructively evaluated for plug height, heat tint, ultrasonic testing (UT) for bond length and ultrasonic volumetric examination for weld defects, burst pressure, fractography, and metallography. The testing was conducted in agreement with a Task Technical and Quality Assurance Plan (TTQAP) (2) and applicable procedures.« less

Recurrence Quantifcation Analysis of Sentence-Level Speech Kinematics

ERIC Educational Resources Information Center

Jackson, Eric S.; Tiede, Mark; Riley, Michael A.; Whalen, D. H.

2016-01-01

Purpose: Current approaches to assessing sentence-level speech variability rely on measures that quantify variability across utterances and use normalization procedures that alter raw trajectory data. The current work tests the feasibility of a less restrictive nonlinear approach--recurrence quantification analysis (RQA)--via a procedural example…

Dispersant approval procedures in France and Italy: A comparative ecotoxicity study.

PubMed

Manfra, Loredana; Tornambè, Andrea; Guyomarch, Julien; Le Guerrogue, Pascale; Kerambrun, Loïc; Rotini, Alice; Savorelli, Federica; Onorati, Fulvio; Magaletti, Erika

2017-09-01

A research project has been performed to the request of the RAMOGE Executive Secretariat to identify differences between dispersant approval procedures in France and Italy and propose ways to harmonize them. A collaborative study has been conducted by CEDRE (Centre of Documentation, Research and Experimentation on Accidental Water Pollution) and ISPRA (Italian Institute for Environmental Protection and Research) to: a) compare current approval procedures in Italy and France with identification of differences and commonalities; b) carry out toxicity tests using both procedures on two selected dispersants; c) propose a common approach between Italy and France. The results showed that, because of the differences in ecotoxicological tests and in the evaluation criteria used, the outcomes on the same products could be different in Italy and in France. Both tested dispersants met the French requirements for approval (LC 50 ≥ 10 times reference toxicant), while only one dispersant met the Italian approval criterion (EC 50 > 10mg/L). A possible way of harmonizing the approval procedures could be to increase the number of test organisms in the French procedure, which currently only uses one crustacean species. Furthermore, a common criterion for toxicity assessment should be discussed and agreed. Copyright © 2017. Published by Elsevier Inc.

A simulator study for the development and evaluation of operating procedures on a supersonic cruise research transport to minimize airport-community noise

NASA Technical Reports Server (NTRS)

Grantham, W. D.; Smith, P. M.; Deal, P. L.

1980-01-01

Piloted-simulator studies were conducted to determine takeoff and landing operating procedures for a supersonic cruise research transport concept that result in predicted noise levels which meet current Federal Aviation Administration (FAA) certification standards. With the use of standard FAA noise certification test procedures, the subject simulated aircraft did not meet the FAA traded-noise-level standards during takeoff and landing. However, with the use of advanced procedures, this aircraft meets the traded-noise-level standards for flight crews with average skills. The advanced takeoff procedures developed involved violating some of the current Federal Aviation Regulations (FAR), but it was not necessary to violate any FAR noise-test conditions during landing approach. Noise contours were also determined for some of the simulated takeoffs and landings in order to indicate the noise-reduction advantages of using operational procedures other than standard.

Direct Field Acoustic Testing

NASA Technical Reports Server (NTRS)

Larkin, Paul; Goldstein, Bob

2008-01-01

This paper presents an update to the methods and procedures used in Direct Field Acoustic Testing (DFAT). The paper will discuss some of the recent techniques and developments that are currently being used and the future publication of a reference standard. Acoustic testing using commercial sound system components is becoming a popular and cost effective way of generating a required acoustic test environment both in and out of a reverberant chamber. This paper will present the DFAT test method, the usual setup and procedure and the development and use of a closed-loop, narrow-band control system. Narrow-band control of the acoustic PSD allows all standard techniques and procedures currently used in random control to be applied to acoustics and some examples are given. The paper will conclude with a summary of the development of a standard practice guideline that is hoped to be available in the first quarter of next year.

Rheoencephalographic and electroencephalographic measures of cognitive workload: analytical procedures.

PubMed

Montgomery, L D; Montgomery, R W; Guisado, R

1995-05-01

This investigation demonstrates the feasibility of mental workload assessment by rheoencephalographic (REG) and multichannel electroencephalographic (EEG) monitoring. During the performance of this research, unique testing, analytical and display procedures were developed for REG and EEG monitoring that extend the current state of the art and provide valuable tools for the study of cerebral circulatory and neural activity during cognition. REG records are analyzed to provide indices of the right and left hemisphere hemodynamic changes that take place during each test sequence. The EEG data are modeled using regression techniques and mathematically transformed to provide energy-density distributions of the scalp electrostatic field. These procedures permit concurrent REG/EEG cognitive testing not possible with current techniques. The introduction of a system for recording and analysis of cognitive REG/EEG test sequences facilitates the study of learning and memory disorders, dementia and other encephalopathies.

Rheoencephalographic and electroencephalographic measures of cognitive workload: analytical procedures

NASA Technical Reports Server (NTRS)

Montgomery, L. D.; Montgomery, R. W.; Guisado, R.

1995-01-01

This investigation demonstrates the feasibility of mental workload assessment by rheoencephalographic (REG) and multichannel electroencephalographic (EEG) monitoring. During the performance of this research, unique testing, analytical and display procedures were developed for REG and EEG monitoring that extend the current state of the art and provide valuable tools for the study of cerebral circulatory and neural activity during cognition. REG records are analyzed to provide indices of the right and left hemisphere hemodynamic changes that take place during each test sequence. The EEG data are modeled using regression techniques and mathematically transformed to provide energy-density distributions of the scalp electrostatic field. These procedures permit concurrent REG/EEG cognitive testing not possible with current techniques. The introduction of a system for recording and analysis of cognitive REG/EEG test sequences facilitates the study of learning and memory disorders, dementia and other encephalopathies.

Evaluation of standardized sample collection, packaging, and ...

EPA Pesticide Factsheets

Journal Sample collection procedures and primary receptacle (sample container and bag) decontamination methods should prevent contaminant transfer between contaminated and non-contaminated surfaces and areas during bio-incident operations. Cross-contamination of personnel, equipment, or sample containers may result in the exfiltration of biological agent from the exclusion (hot) zone and have unintended negative consequences on response resources, activities and outcomes. The current study was designed to: (1) evaluate currently recommended sample collection and packaging procedures to identify procedural steps that may increase the likelihood of spore exfiltration or contaminant transfer; (2) evaluate the efficacy of currently recommended primary receptacle decontamination procedures; and (3) evaluate the efficacy of outer packaging decontamination methods. Wet- and dry-deposited fluorescent tracer powder was used in contaminant transfer tests to qualitatively evaluate the currently-recommended sample collection procedures. Bacillus atrophaeus spores, a surrogate for Bacillus anthracis, were used to evaluate the efficacy of spray- and wipe-based decontamination procedures.

Hanford spent nuclear fuel hot conditioning system test procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleveland, K.J.

1997-09-16

This document provides the test procedures for cold testing of the prototype Hot Conditioning System (HCS) at the 306E Facility. The primary objective of this testing is to confirm design choices and provide data for the detailed design package prior to procurement of the process equipment. The current scope of testing in this document includes a fabricability study of the HCS, equipment performance testing of the HCS components, heat-up and cool-down cycle simulation, and robotic arm testing.

In-Situ Measurement of Power Loss for Crystalline Silicon Modules Undergoing Thermal Cycling and Mechanical Loading Stress Testing: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spataru, Sergiu; Hacke, Pater; Sera, Dezso

2015-09-15

We analyze the degradation of multi-crystalline silicon photovoltaic modules undergoing simultaneous thermal, mechanical, and humidity stress testing to develop a dark environmental chamber in-situ measurement procedure for determining module power loss. From the analysis we determine three main categories of failure modes associated with the module degradation consisting of: shunting, recombination losses, increased series resistance losses, and current mismatch losses associated with a decrease in photo-current generation by removal of some cell areas due to cell fractures. Based on the analysis, we propose an in-situ module power loss monitoring procedure that relies on dark current-voltage measurements taken during the stressmore » test, and initial and final module flash testing, to determine the power degradation characteristic of the module.« less

32 CFR 1701.13 - Special procedures for medical/psychiatric/psychological records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Special procedures for medical/psychiatric... procedures for medical/psychiatric/psychological records. Current and former ODNI employees, including... access to their medical, psychiatric or psychological testing records by writing to: Information and...

Gasoline and Diesel Fuel Test Methods Additional Resources

EPA Pesticide Factsheets

Supporting documents on the Direct Final Rule that allows refiners and laboratories to use more current and improved fuel testing procedures for twelve American Society for Testing and Materials analytical test methods.

75 FR 17075 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... different in mathematical form, is conceptually the same as the integrated AFUE for fossil fueled furnaces... that gas-fired and oil-fried furnaces and boilers consume both fossil fuel and electricity, while electric furnaces and boilers only consume electricity. The current test procedure accounts for all fossil...

Development of Subscale Fast Cookoff Test (PREPRINT)

DTIC Science & Technology

2006-09-21

The hazards classification procedures have been harmonized with both the UN Test and Criteria Manual for UN Series 1...aimed at the development of a sub-scale alternate test protocol to the external fire test currently required for final hazards classification (HC...external fire test currently required for final hazards classification (HC) of an ordnance system. The specific goal of this part of the task was

Topical Hazard Evaluation Program Procedural Guide.

DTIC Science & Technology

1982-01-01

conditions and are percent (w/v) Oil of tion reaction under test not expected to cause a Bergamot solution conditions. photochemical irritation...photochemical skin irritant ( Bergamot oil). d. All compounds-are handled with caution. Current test procedures cannot eliminate the possibility of individual...percent ethyl alcohol. One additional compound applied along with the test compounds is a 10 percent solution (w/v) of Bergamot oil" in 95 percent ethyl

75 FR 8526 - Procedures for Transportation Workplace Drug and Alcohol Testing Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-25

... regarding the interim final rule (IFR) procedures for the use of a new alcohol screening device (ASD) which... for an employer to utilize a specific ASD to conduct required DOT alcohol tests, the device must (a... model specifications, (b) be published by NHTSA in the Federal Register on their most current ASD CPL...

77 FR 22637 - Federal Motor Vehicle Safety Standards; Accelerator Control Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-16

... severing a conductor at one location. The current language of the test procedure in FMVSS No. 124 is... routinely have variable valve lift and/or timing control. In at least one recent engine design, the level of.... Under the 2002 NPRM, a manufacturer could choose any one of the proposed test procedures as a basis for...

Large Area Crop Inventory Experiment (LACIE). Second-generation sampling strategy evaluation report. [Kansas, North Dakota, and U.S.S.R.

NASA Technical Reports Server (NTRS)

Basu, J. P. (Principal Investigator); Dragich, S. M.; Mcguigan, D. P.

1978-01-01

The author has identified the following significant results. The stratification procedure in the new sampling strategy for LACIE included: (1) correlation test results indicating that an agrophysical stratum may be homogeneous with respect to agricultural density, but not with respect to wheat density; and (2) agrophysical unit homogeneity test results indicating that with respect to agricultural density many agrophysical units are not homogeneous, but removal of one or more refined strata from any such current agrophysical unit can make the strata homogeneous. The apportioning procedure results indicated that the current procedure is not performing well and that the apportioned estimates of refined strata wheat area are often unreliable.

XML syntax for clinical laboratory procedure manuals.

PubMed

Saadawi, Gilan; Harrison, James H

2003-01-01

We have developed a document type description (DTD) in Extensable Markup Language (XML) for clinical laboratory procedures. Our XML syntax can adequately structure a variety of procedure types across different laboratories and is compatible with current procedure standards. The combination of this format with an XML content management system and appropriate style sheets will allow efficient procedure maintenance, distributed access, customized display and effective searching across a large body of test information.

Detecting defects in marine structures by using eddy current infrared thermography.

PubMed

Swiderski, W

2016-12-01

Eddy current infrared (IR) thermography is a new nondestructive testing (NDT) technique used for the detection of cracks in electroconductive materials. By combining the well-established inspection methods of eddy current NDT and IR thermography, this technique uses induced eddy currents to heat test samples. In this way, IR thermography allows the visualization of eddy current distribution that is distorted in defect sites. This paper discusses the results of numerical modeling of eddy current IR thermography procedures in application to marine structures.

Constructing Aligned Assessments Using Automated Test Construction

ERIC Educational Resources Information Center

Porter, Andrew; Polikoff, Morgan S.; Barghaus, Katherine M.; Yang, Rui

2013-01-01

We describe an innovative automated test construction algorithm for building aligned achievement tests. By incorporating the algorithm into the test construction process, along with other test construction procedures for building reliable and unbiased assessments, the result is much more valid tests than result from current test construction…

Measurement of impulsive choice in rats: Same and alternate form test-retest reliability and temporal tracking

PubMed Central

Peterson, Jennifer R.; Hill, Catherine C.; Kirkpatrick, Kimberly

2016-01-01

Impulsive choice is typically measured by presenting smaller-sooner (SS) versus larger-later (LL) rewards, with biases towards the SS indicating impulsivity. The current study tested rats on different impulsive choice procedures with LL delay manipulations to assess same-form and alternate-form test-retest reliability. In the systematic-GE procedure (Green & Estle, 2003), the LL delay increased after several sessions of training; in the systematic-ER procedure (Evenden & Ryan, 1996), the delay increased within each session; and in the adjusting-M procedure (Mazur, 1987), the delay changed after each block of trials within a session based on each rat’s choices in the previous block. In addition to measuring choice behavior, we also assessed temporal tracking of the LL delays using the median times of responding during LL trials. The two systematic procedures yielded similar results in both choice and temporal tracking measures following extensive training, whereas the adjusting procedure resulted in relatively more impulsive choices and poorer temporal tracking. Overall, the three procedures produced acceptable same form test-retest reliability over time, but the adjusting procedure did not show significant alternate form test-retest reliability with the other two procedures. The results suggest that systematic procedures may supply better measurements of impulsive choice in rats. PMID:25490901

49 CFR 40.160 - What does the MRO do when a valid test result cannot be produced and a negative result is required?

Code of Federal Regulations, 2010 CFR

2010-10-01

... determine if there is clinical evidence that the individual is currently an illicit drug user. You must make... Secretary of Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS...., blood) as part of the medically appropriate procedures in determining clinical evidence of drug use. (d...

Psychophysical tests for DWI arrest

DOT National Transportation Integrated Search

1977-06-01

As part of DWI arrest procedures, tests of alcohol impairment may be used by police officers, either at roadside or in the station. Objectives of this study included evaluation of currently-used tests, development of more sensitive and reliable measu...

Strategies for controlling item exposure in computerized adaptive testing with the partial credit model.

PubMed

Davis, Laurie Laughlin; Dodd, Barbara G

2008-01-01

Exposure control research with polytomous item pools has determined that randomization procedures can be very effective for controlling test security in computerized adaptive testing (CAT). The current study investigated the performance of four procedures for controlling item exposure in a CAT under the partial credit model. In addition to a no exposure control baseline condition, the Kingsbury-Zara, modified-within-.10-logits, Sympson-Hetter, and conditional Sympson-Hetter procedures were implemented to control exposure rates. The Kingsbury-Zara and the modified-within-.10-logits procedures were implemented with 3 and 6 item candidate conditions. The results show that the Kingsbury-Zara and modified-within-.10-logits procedures with 6 item candidates performed as well as the conditional Sympson-Hetter in terms of exposure rates, overlap rates, and pool utilization. These two procedures are strongly recommended for use with partial credit CATs due to their simplicity and strength of their results.

Representing operations procedures using temporal dependency networks

NASA Technical Reports Server (NTRS)

Fayyad, Kristina E.; Cooper, Lynne P.

1993-01-01

DSN Link Monitor & Control (LMC) operations consist primarily of executing procedures to configure, calibrate, test, and operate a communications link between an interplanetary spacecraft and its mission control center. Currently the LMC operators are responsible for integrating procedures into an end-to-end series of steps. The research presented in this paper is investigating new ways of specifying operations procedures that incorporate the insight of operations, engineering, and science personnel to improve mission operations. The paper describes the rationale for using Temporal Dependency Networks (TDN's) to represent the procedures, a description of how the data is acquired, and the knowledge engineering effort required to represent operations procedures. Results of operational tests of this concept, as implemented in the LMC Operator Assistant Prototype (LMCOA), are also presented.

Conducted-Susceptibility Testing as an Alternative Approach to Unit-Level Radiated-Susceptibility Verifications

NASA Astrophysics Data System (ADS)

Badini, L.; Grassi, F.; Pignari, S. A.; Spadacini, G.; Bisognin, P.; Pelissou, P.; Marra, S.

2016-05-01

This work presents a theoretical rationale for the substitution of radiated-susceptibility (RS) verifications defined in current aerospace standards with an equivalent conducted-susceptibility (CS) test procedure based on bulk current injection (BCI) up to 500 MHz. Statistics is used to overcome the lack of knowledge about uncontrolled or uncertain setup parameters, with particular reference to the common-mode impedance of equipment. The BCI test level is properly investigated so to ensure correlation of currents injected in the equipment under test via CS and RS. In particular, an over-testing probability quantifies the severity of the BCI test with respect to the RS test.

Test Operations Procedure (TOP) 05-2-543 Enhanced Flight Termination Receiver (EFTR) Range Certification Testing

DTIC Science & Technology

2011-07-25

testing, the EFTR must be keyed with the same key used to encrypt the Enhanced Flight Termination Systems ( EFTS ) message. To ensure identical keys...required to verify the proper state. e. Procedure. (1) Pull up EFTS graphic user interface (GUI) (Figure 3). (2) Click “Receiver Power On...commanded mode steady state input currents will not exceed their specified values. TOP 05-2-543 25 July 2011 19 Figure 3. EFTS GUIa

Understanding Achievement Tests: A Guide for School Administrators.

ERIC Educational Resources Information Center

Rudner, Lawrence M., Ed.; Conoley, Jane Close; Plake, Barbara S.

Current information about tests and testing procedures is provided for school district staff, particularly in districts without specially trained testing directors. Practical information is given about selecting and administering tests and about reporting results effectively. This guide opens with a discussion of the basic principles of testing.…

75 FR 79320 - Animal Drugs, Feeds, and Related Products; Regulation of Carcinogenic Compounds in Food-Producing...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-20

... is calculated from tumor data of the cancer bioassays using a statistical extrapolation procedure... carcinogenic concern currently set forth in Sec. 500.84 utilizes a statistical extrapolation procedure that... procedures did not rely on a statistical extrapolation of the data to a 1 in 1 million risk of cancer to test...

Lateral and longitudinal aerodynamic stability and control parameters of the basic vortex flap research aircraft as determined from flight test data

NASA Technical Reports Server (NTRS)

Suit, W. T.; Batterson, J. G.

1986-01-01

The aerodynamics of the basic F-106B were determined at selected points in the flight envelope. The test aircraft and flight procedures were presented. Aircraft instrumentation and the data system were discussed. The parameter extraction procedure was presented along with a discussion of the test flight results. The results were used to predict the aircraft motions for maneuvers that were not used to determine the vehicle aerodynamics. The control inputs used to maneuver the aircraft to get data for the determination of the aerodynamic parameters were discussed in the flight test procedures. The results from the current flight tests were compared with the results from wind tunnel test of the basic F-106B.

The Need and Requirements for Validating Damage Detection Capability

DTIC Science & Technology

2011-09-01

Testing of Airborne Equipment [11], 2) Materials / Structure Certification, 3) NDE (POD) Validation Procedures, 4) Failure Mode Effects and Criticality...Analysis (FMECA), and 5) Cost Benefits Analysis [12]. Existing procedures for environmental testing of airborne equipment ensure flight...e.g. ultrasound or eddy current), damage type or failure conditions to detect, criticality of the damage state (e.g. safety of flight), likelihood of

Using the Implicit Association Test and the Implicit Relational Assessment Procedure to Measure Attitudes toward Meat and Vegetables in Vegetarians and Meat-Eaters

ERIC Educational Resources Information Center

Barnes-Holmes, Dermot; Murtagh, Louise; Barnes-Holmes, Yvonne; Stewart, Ian

2010-01-01

The current study aimed to assess the implicit attitudes of vegetarians and non-vegetarians towards meat and vegetables, using the Implicit Association Test (IAT) and the Implicit Relational Assessment Procedure (IRAP). Both measures involved asking participants to respond, under time pressure, to pictures of meat or vegetables as either positive…

NASA Glenn's Acoustical Testing Laboratory Awarded Accreditation by the National Voluntary Laboratory Accreditation Program

NASA Technical Reports Server (NTRS)

Akers, James C.; Cooper, Beth A.

2004-01-01

NASA Glenn Research Center's Acoustical Testing Laboratory (ATL) provides a comprehensive array of acoustical testing services, including sound pressure level, sound intensity level, and sound-power-level testing per International Standards Organization (ISO)1 3744. Since its establishment in September 2000, the ATL has provided acoustic emission testing and noise control services for a variety of customers, particularly microgravity space flight hardware that must meet International Space Station acoustic emission requirements. The ATL consists of a 23- by 27- by 20-ft (height) convertible hemi/anechoic test chamber and a separate sound-attenuating test support enclosure. The ATL employs a personal-computer-based data acquisition system that provides up to 26 channels of simultaneous data acquisition with real-time analysis (ref. 4). Specialized diagnostic tools, including a scanning sound-intensity system, allow the ATL's technical staff to support its clients' aggressive low-noise design efforts to meet the space station's acoustic emission requirement. From its inception, the ATL has pursued the goal of developing a comprehensive ISO 17025-compliant quality program that would incorporate Glenn's existing ISO 9000 quality system policies as well as ATL-specific technical policies and procedures. In March 2003, the ATL quality program was awarded accreditation by the National Voluntary Laboratory Accreditation Program (NVLAP) for sound-power-level testing in accordance with ISO 3744. The NVLAP program is administered by the National Institutes of Standards and Technology (NIST) of the U.S. Department of Commerce and provides third-party accreditation for testing and calibration laboratories. There are currently 24 NVLAP-accredited acoustical testing laboratories in the United States. NVLAP accreditation covering one or more specific testing procedures conducted in accordance with established test standards is awarded upon successful completion of an intensive onsite assessment that includes proficiency testing and documentation review. The ATL NVLAP accreditation currently applies specifically to its ISO 3744 soundpower- level determination procedure (see the photograph) and supporting ISO 17025 quality system, although all ATL operations are conducted in accordance with its quality system. The ATL staff is currently developing additional procedures to adapt this quality system to the testing of space flight hardware in accordance with International Space Station acoustic emission requirements.<

Expedient Approaches for the Management of Wastes ...

EPA Pesticide Factsheets

Report The current study sought to determine waste decontamination conditions that would achieve complete kill for all material types. For these tests, more stringent decontamination procedures were evaluated specifically using pAB amended with a surfactant and/or waste submersion procedures involving agitation.

30 CFR 77.900-1 - Testing, examination, and maintenance of circuit breakers; procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... protecting low- and medium-voltage circuits serving portable or mobile three-phase alternating current... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits...

30 CFR 77.900-1 - Testing, examination, and maintenance of circuit breakers; procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... protecting low- and medium-voltage circuits serving portable or mobile three-phase alternating current... AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits...

34 CFR 668.144 - Application for test approval.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the comparability of scores on the current test to scores on the previous test, and data from validity... explanation of the methodology and procedures for measuring the reliability of the test; (ii) Evidence that different forms of the test, including, if applicable, short forms, are comparable in reliability; (iii...

Nuclear medicine in clinical urology and nephrology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tauxe, W.N.; Dubousky, E.V.

This book presents explanations of current procedures involving the kidney with information of the performance of each test, its rationale, and interpretation. The information covers all currently used radiopharmaceuticals, radiation dosimetry, instrumentation, test protocols, and mathematical principles of pathophysiology as they relate to nuclear medicine studies. Information is provided on which radiopharmaceutical, instrument, or computer application to use, and when.

Parameter estimation in astronomy through application of the likelihood ratio. [satellite data analysis techniques

NASA Technical Reports Server (NTRS)

Cash, W.

1979-01-01

Many problems in the experimental estimation of parameters for models can be solved through use of the likelihood ratio test. Applications of the likelihood ratio, with particular attention to photon counting experiments, are discussed. The procedures presented solve a greater range of problems than those currently in use, yet are no more difficult to apply. The procedures are proved analytically, and examples from current problems in astronomy are discussed.

Investigation of the effects of external current systems on the MAGSAT data utilizing grid cell modeling techniques

NASA Technical Reports Server (NTRS)

Klumpar, D. M. (Principal Investigator)

1982-01-01

The status of the initial testing of the modeling procedure developed to compute the magnetic fields at satellite orbit due to current distributions in the ionosphere and magnetosphere is reported. The modeling technique utilizes a linear current element representation of the large scale space-current system.

Butyl rubber O-ring seals: Revision of test procedures for stockpile materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domeier, L.A.; Wagter, K.R.

1996-12-01

Extensive testing showed little correlation between test slab and O-ring performance. New procedures, comparable to those used with the traditional test slabs, were defined for hardness, compression set, and tensile property testing on sacrificial O-ring specimens. Changes in target performance values were made as needed and were, in one case, tightened to reflect the O-ring performance data. An additional study was carried out on O-ring and slab performance vs cure cycle and showed little sensitivity of material performance to large changes in curing time. Aging and spectra of certain materials indicated that two sets of test slabs from current vendormore » were accidently made from EPDM rather than butyl rubber. Random testing found no O-rings made from EPDM. As a result, and additional spectroscope test will be added to the product acceptance procedures to verify the type of rubber compound used.« less

Validation of the MEPDG transfer functions using the LTPP test sections in Georgia task 2 interim report.

DOT National Transportation Integrated Search

2013-07-16

The Georgia Department of Transportation (GDOT) is transitioning from empirical design procedures to the MEPDG : procedure for designing new and rehabilitated highway pavements. GDOT currently uses the 1972 AASHTO Interim : Guide for Design of Paveme...

A universal procedure for evaluation and application of surge-protective devices

NASA Technical Reports Server (NTRS)

1980-01-01

The source, nature, and frequency of occurrence of transients must be identified and a representative standard test wave chosen for proof testing. The performance of candidate suppressor devices then can be evaluated against the withstand goals set for the equipment. The various suppressors divide into two classes of generic behavior. The key to a universal procedure for evaluating both classes lies in representing transients as quasi-current sources of defined current impulse duration. The available surge current is established by the Thevenin equivalent transient voltage and source impedance. A load line drawn on the V-I characteristic graph of the suppressor quickly determines the clamping voltage and peak current. These values then can be compared to the requirement. The deposited energy and average power dissipation for multiple transients also can be calculated. The method is illustrated with a design example for motor vehicle alternator load dump suppression.

Development and proposed implementation of a field permeability test for a asphalt concrete.

DOT National Transportation Integrated Search

2001-07-01

The objectives of this study were as follows: : 1) To review research performed by others and determine the state-of-the-art of field permeability measurements; : 2) To review current laboratory permeability testing devices and their testing procedur...

Examining the Validity of GED[R] Tests Scores with Scheduling and Setting Accommodations. GED Testing Service Research Studies, 2004-1

ERIC Educational Resources Information Center

George-Ezzelle, Carol E.; Skaggs, Gary

2004-01-01

Current testing standards call for test developers to provide evidence that testing procedures and test scores, and the inferences made based on the test scores, show evidence of validity and are comparable across subpopulations (American Educational Research Association [AERA], American Psychological Association [APA], & National Council on…

Acoustic flight test of the Piper Lance

DOT National Transportation Integrated Search

1986-12-01

Research is being conducted to refine current noise regulation of propeller-driven small airplanes. Studies are examining the prospect of a substituting a takeoff procedure of equal stringency for the level flyover certification test presently requir...

42 CFR 410.32 - Diagnostic x-ray tests, diagnostic laboratory tests, and other diagnostic tests: Conditions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... in the 80000 series of the Current Procedural Terminology published by the American Medical... & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICARE PROGRAM SUPPLEMENTARY MEDICAL INSURANCE (SMI) BENEFITS Medical and Other Health Services § 410.32 Diagnostic x-ray tests, diagnostic laboratory...

Python Scripts for Automation of Current-Voltage Testing of Semiconductor Devices (FY17)

DTIC Science & Technology

2017-01-01

ARL-TR-7923 ● JAN 2017 US Army Research Laboratory Python Scripts for Automation of Current- Voltage Testing of Semiconductor...manual device-testing procedures is reduced or eliminated through automation. This technical report includes scripts written in Python , version 2.7, used ...nothing. 3.1.9 Exit Program The script exits the entire program. Line 505, sys.exit(), uses the sys package that comes with Python to exit system

Revision of OECD Guidelines for Genotoxicity Testing: Current Status and Next Steps

EPA Science Inventory

Over the past 30 years, assays have been developed to evaluate chemical genotoxicity. OECD Genotoxicity Test Guidelines (TG) describe assay procedures for regulatory safety testing. Since the last OECD TG revision (1997), there has been tremendous scientific and technological pro...

Residential Two-Stage Gas Furnaces - Do They Save Energy?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lekov, Alex; Franco, Victor; Lutz, James

2006-05-12

Residential two-stage gas furnaces account for almost a quarter of the total number of models listed in the March 2005 GAMA directory of equipment certified for sale in the United States. Two-stage furnaces are expanding their presence in the market mostly because they meet consumer expectations for improved comfort. Currently, the U.S. Department of Energy (DOE) test procedure serves as the method for reporting furnace total fuel and electricity consumption under laboratory conditions. In 2006, American Society of Heating Refrigeration and Air-conditioning Engineers (ASHRAE) proposed an update to its test procedure which corrects some of the discrepancies found in themore » DOE test procedure and provides an improved methodology for calculating the energy consumption of two-stage furnaces. The objectives of this paper are to explore the differences in the methods for calculating two-stage residential gas furnace energy consumption in the DOE test procedure and in the 2006 ASHRAE test procedure and to compare test results to research results from field tests. Overall, the DOE test procedure shows a reduction in the total site energy consumption of about 3 percent for two-stage compared to single-stage furnaces at the same efficiency level. In contrast, the 2006 ASHRAE test procedure shows almost no difference in the total site energy consumption. The 2006 ASHRAE test procedure appears to provide a better methodology for calculating the energy consumption of two-stage furnaces. The results indicate that, although two-stage technology by itself does not save site energy, the combination of two-stage furnaces with BPM motors provides electricity savings, which are confirmed by field studies.« less

Adhesion testing procedure for hot-poured crack sealants.

DOT National Transportation Integrated Search

2008-11-01

Crack sealing is a common pavement maintenance treatment because it extends pavement service life significantly. : However, crack sealant often fails prematurely due to a loss of adhesion. Because current test methods are mostly : empirical and only ...

49 CFR 40.33 - What training requirements must a collector meet?

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Collection Personnel § 40.33 What training... about this part, the current “DOT Urine Specimen Collection Procedures Guidelines,” and DOT agency... changes to these materials. The DOT Urine Specimen Collection Procedures Guidelines document is available...

49 CFR 40.33 - What training requirements must a collector meet?

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Collection Personnel § 40.33 What training... about this part, the current “DOT Urine Specimen Collection Procedures Guidelines,” and DOT agency... changes to these materials. The DOT Urine Specimen Collection Procedures Guidelines document is available...

49 CFR 40.33 - What training requirements must a collector meet?

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Collection Personnel § 40.33 What training... about this part, the current “DOT Urine Specimen Collection Procedures Guidelines,” and DOT agency... changes to these materials. The DOT Urine Specimen Collection Procedures Guidelines document is available...

49 CFR 40.33 - What training requirements must a collector meet?

Code of Federal Regulations, 2010 CFR

2010-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Collection Personnel § 40.33 What training... about this part, the current “DOT Urine Specimen Collection Procedures Guidelines,” and DOT agency... changes to these materials. The DOT Urine Specimen Collection Procedures Guidelines document is available...

49 CFR 40.33 - What training requirements must a collector meet?

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Urine Collection Personnel § 40.33 What training... about this part, the current “DOT Urine Specimen Collection Procedures Guidelines,” and DOT agency... changes to these materials. The DOT Urine Specimen Collection Procedures Guidelines document is available...

DNA-testing for BRCA1/2 prior to genetic counselling in patients with breast cancer: design of an intervention study, DNA-direct.

PubMed

Sie, Aisha S; Spruijt, Liesbeth; van Zelst-Stams, Wendy A G; Mensenkamp, Arjen R; Ligtenberg, Marjolijn J; Brunner, Han G; Prins, Judith B; Hoogerbrugge, Nicoline

2012-05-08

Current practice for patients with breast cancer referred for genetic counseling, includes face-to-face consultations with a genetic counselor prior to and following DNA-testing. This is based on guidelines regarding Huntington's disease in anticipation of high psychosocial impact of DNA-testing for mutations in BRCA1/2 genes. The initial consultation covers generic information regarding hereditary breast cancer and the (im)possibilities of DNA-testing, prior to such testing. Patients with breast cancer may see this information as irrelevant or unnecessary because individual genetic advice depends on DNA-test results. Also, verbal information is not always remembered well by patients. A different format for this information prior to DNA-testing is possible: replacing initial face-to-face genetic counseling (DNA-intake procedure) by telephone, written and digital information sent to patients' homes (DNA-direct procedure). In this intervention study, 150 patients with breast cancer referred to the department of Clinical Genetics of the Radboud University Nijmegen Medical Centre are given the choice between two procedures, DNA-direct (intervention group) or DNA-intake (usual care, control group). During a triage telephone call, patients are excluded if they have problems with Dutch text, family communication, or of psychological or psychiatric nature. Primary outcome measures are satisfaction and psychological distress. Secondary outcome measures are determinants for the participant's choice of procedure, waiting and processing times, and family characteristics. Data are collected by self-report questionnaires at baseline and following completion of genetic counseling. A minority of participants will receive an invitation for a 30 min semi-structured telephone interview, e.g. confirmed carriers of a BRCA1/2 mutation, and those who report problems with the procedure. This study compares current practice of an intake consultation (DNA-intake) to a home informational package of telephone, written and digital information (DNA-direct) prior to DNA-testing in patients with breast cancer. The aim is to determine whether DNA-direct is an acceptable procedure for BRCA1/2 testing, in order to provide customized care to patients with breast cancer, cutting down on the period of uncertainty during this diagnostic process.

An Alternative Approach to Identifying a Dimension in Second Language Proficiency.

ERIC Educational Resources Information Center

Griffin, Patrick E.; And Others

Current practice in language testing has not yet integrated classical test theory with assessment of language skills. In addition, language testing needs to be part of theory development. Lack of sound testing procedures can lead to problems in research design and ultimately, inappropriate theory development. The debate over dimensionality of…

Southwest electronic one-stop shopping, motor carrier test report

DOT National Transportation Integrated Search

1997-12-22

The Electronic One-Stop System (EOSS) used in this credential test was designed to replace current normal credentialling procedures with a personal computer-based electronic method that allows users to prepare, apply for, and obtain certain types of ...

Southwest electronic one-stop shopping, state agency test report

DOT National Transportation Integrated Search

1997-12-22

The Electronic One-Stop System (EOSS) used in this credential test was designed to replace current normal credentialling procedures with a personal computer-based electronic method that allows users to prepare, apply for, and obtain certain types of ...

NPS Solar Cell Array Tester Cubesat Flight Testing and Integration

DTIC Science & Technology

2014-09-01

with current (I). P V I      (2.1) This is significant because the battery discharge test will not lineup perfectly with Figure 12...accordance with the charging procedures [13]. 3. NPS-SCAT Power Budget A power budget analysis was performed to determine if the NPS-SCAT is self...using procedures developed by Marissa Brummitt, and with the assistance of Adam Hill, NPS-SCAT Program Manager. 1. ELaNa IV Random Vibration Levels

Traceable measurements of the electrical parameters of solid-state lighting products

NASA Astrophysics Data System (ADS)

Zhao, D.; Rietveld, G.; Braun, J.-P.; Overney, F.; Lippert, T.; Christensen, A.

2016-12-01

In order to perform traceable measurements of the electrical parameters of solid-state lighting (SSL) products, it is necessary to technically adequately define the measurement procedures and to identify the relevant uncertainty sources. The present published written standard for SSL products specifies test conditions, but it lacks an explanation of how adequate these test conditions are. More specifically, both an identification of uncertainty sources and a quantitative uncertainty analysis are absent. This paper fills the related gap in the present written standard. New uncertainty sources with respect to conventional lighting sources are determined and their effects are quantified. It shows that for power measurements, the main uncertainty sources are temperature deviation, power supply voltage distortion, and instability of the SSL product. For current RMS measurements, the influence of bandwidth, shunt resistor, power supply source impedance and ac frequency flatness are significant as well. The measurement uncertainty depends not only on the test equipment but is also a function of the characteristics of the device under test (DUT), for example, current harmonics spectrum and input impedance. Therefore, an online calculation tool is provided to help non-electrical experts. Following our procedures, unrealistic uncertainty estimations, unnecessary procedures and expensive equipment can be prevented.

North Dakota implementation of mechanistic-empirical pavement design guide (MEPDG).

DOT National Transportation Integrated Search

2014-12-01

North Dakota currently designs roads based on the AASHTO Design Guide procedure, which is based on : the empirical findings of the AASHTO Road Test of the late 1950s. However, limitations of the current : empirical approach have prompted AASHTO to mo...

77 FR 28927 - Energy Conservation Program for Certain Industrial Equipment: Energy Conservation Standards and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

...The U.S. Department of Energy (DOE) is amending its energy conservation standards for small, large, and very large water-cooled and evaporatively-cooled commercial package air conditioners, and variable refrigerant flow (VRF) water-source heat pumps less than 17,000 Btu/h. DOE is adopting new energy conservation standards for computer room air conditioners and VRF water-source heat pumps with a cooling capacity at or greater than 135,000 Btu/h and less than 760,000 Btu/h. Pursuant to the Energy Policy and Conservation Act of 1975 (EPCA), as amended, DOE must assess whether the uniform national standards for these covered equipment need to be updated each time the corresponding industry standard--the American National Standards Institute (ANSI)/American Society of Heating, Refrigerating, and Air- Conditioning Engineers (ASHRAE)/Illuminating Engineering Society of North America (IESNA) Standard 90.1 (ASHRAE Standard 90.1)--is amended, which most recently occurred on October 29, 2010. The levels DOE is adopting are the same as the efficiency levels specified in ASHRAE Standard 90.1-2010. DOE has determined that the ASHRAE Standard 90.1- 2010 efficiency levels for the equipment types listed above are more stringent than existing Federal energy conservation standards and will result in economic and energy savings compared existing energy conservation standards. Furthermore, DOE has concluded that clear and convincing evidence does not exist, as would justify more-stringent standard levels than the efficiency levels in ASHRAE Standard 90.1-2010 for any of the equipment classes. DOE is also updating the current Federal test procedures or, for certain equipment, adopting new test procedures to incorporate by reference the most current versions of the relevant industry test procedures specified in ASHRAE Standard 90.1- 2010. Furthermore, DOE is adopting additional test procedure provisions to include with modification certain instructions from Air- Conditioning, Heating, and Refrigeration Institute (AHRI) operations manuals in that organization's test procedures that would clarify the application of the DOE test procedures and harmonize DOE testing with the testing performed by industry.

75 FR 43045 - Pistachios Grown in California, Arizona, and New Mexico; Modification of the Aflatoxin Regulations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-23

.... SUMMARY: This rule modifies the aflatoxin sampling and testing regulations currently prescribed under the... Administrative Committee for Pistachios (Committee). This rule streamlines the aflatoxin sampling and testing... by providing a uniform and consistent aflatoxin sampling and testing procedure for pistachios shipped...

Numerical CFD Simulation and Test Correlation in a Flight Project Environment

NASA Technical Reports Server (NTRS)

Gupta, K. K.; Lung, S. F.; Ibrahim, A. H.

2015-01-01

This paper presents detailed description of a novel CFD procedure and comparison of its solution results to that obtained by other available CFD codes as well as actual flight and wind tunnel test data pertaining to the GIII aircraft, currently undergoing flight testing at AFRC.

76 FR 58345 - Energy Conservation Program: Test Procedures for Residential Dishwashers, Dehumidifiers, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-20

...Where appropriate, the U.S. Department of Energy (DOE) has proposed to amend its test procedures for residential dishwashers, dehumidifiers, and conventional cooking products (which includes cooktops, ovens, and ranges) to include provisions for measuring standby mode and off mode energy consumption, as required by the Energy Independence and Security Act of 2007 (EISA 2007). These test procedure amendments would incorporate by reference certain provisions of the International Electrotechnical Commission (IEC) Standard 62301, ``Household electrical appliances--Measurement of standby power.'' Since publication of DOE's initial proposal in December 2010, the IEC has replaced the First Edition of this standard with the current Second Edition. This supplemental notice of proposed rulemaking proposes to incorporate the latest edition of IEC Standard 62301.

Cognitive and Linguistic Sources of Variance in 2-Year-Olds’ Speech-Sound Discrimination: A Preliminary Investigation

PubMed Central

Lalonde, Kaylah; Holt, Rachael Frush

2017-01-01

Purpose This preliminary investigation explored potential cognitive and linguistic sources of variance in 2-year-olds’ speech-sound discrimination by using the toddler change/no-change procedure and examined whether modifications would result in a procedure that can be used consistently with younger 2-year-olds. Method Twenty typically developing 2-year-olds completed the newly modified toddler change/no-change procedure. Behavioral tests and parent report questionnaires were used to measure several cognitive and linguistic constructs. Stepwise linear regression was used to relate discrimination sensitivity to the cognitive and linguistic measures. In addition, discrimination results from the current experiment were compared with those from 2-year-old children tested in a previous experiment. Results Receptive vocabulary and working memory explained 56.6% of variance in discrimination performance. Performance was not different on the modified toddler change/no-change procedure used in the current experiment from in a previous investigation, which used the original version of the procedure. Conclusions The relationship between speech discrimination and receptive vocabulary and working memory provides further evidence that the procedure is sensitive to the strength of perceptual representations. The role for working memory might also suggest that there are specific subject-related, nonsensory factors limiting the applicability of the procedure to children who have not reached the necessary levels of cognitive and linguistic development. PMID:24023371

Cognitive and linguistic sources of variance in 2-year-olds’ speech-sound discrimination: a preliminary investigation.

PubMed

Lalonde, Kaylah; Holt, Rachael Frush

2014-02-01

This preliminary investigation explored potential cognitive and linguistic sources of variance in 2-year-olds’ speech-sound discrimination by using the toddler change/ no-change procedure and examined whether modifications would result in a procedure that can be used consistently with younger 2-year-olds. Twenty typically developing 2-year-olds completed the newly modified toddler change/no-change procedure. Behavioral tests and parent report questionnaires were used to measure several cognitive and linguistic constructs. Stepwise linear regression was used to relate discrimination sensitivity to the cognitive and linguistic measures. In addition, discrimination results from the current experiment were compared with those from 2-year-old children tested in a previous experiment. Receptive vocabulary and working memory explained 56.6% of variance in discrimination performance. Performance was not different on the modified toddler change/no-change procedure used in the current experiment from in a previous investigation, which used the original version of the procedure. The relationship between speech discrimination and receptive vocabulary and working memory provides further evidence that the procedure is sensitive to the strength of perceptual representations. The role for working memory might also suggest that there are specific subject-related, nonsensory factors limiting the applicability of the procedure to children who have not reached the necessary levels of cognitive and linguistic development.

The Sequential Probability Ratio Test: An efficient alternative to exact binomial testing for Clean Water Act 303(d) evaluation.

PubMed

Chen, Connie; Gribble, Matthew O; Bartroff, Jay; Bay, Steven M; Goldstein, Larry

2017-05-01

The United States's Clean Water Act stipulates in section 303(d) that states must identify impaired water bodies for which total maximum daily loads (TMDLs) of pollution inputs into water bodies are developed. Decision-making procedures about how to list, or delist, water bodies as impaired, or not, per Clean Water Act 303(d) differ across states. In states such as California, whether or not a particular monitoring sample suggests that water quality is impaired can be regarded as a binary outcome variable, and California's current regulatory framework invokes a version of the exact binomial test to consolidate evidence across samples and assess whether the overall water body complies with the Clean Water Act. Here, we contrast the performance of California's exact binomial test with one potential alternative, the Sequential Probability Ratio Test (SPRT). The SPRT uses a sequential testing framework, testing samples as they become available and evaluating evidence as it emerges, rather than measuring all the samples and calculating a test statistic at the end of the data collection process. Through simulations and theoretical derivations, we demonstrate that the SPRT on average requires fewer samples to be measured to have comparable Type I and Type II error rates as the current fixed-sample binomial test. Policymakers might consider efficient alternatives such as SPRT to current procedure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Assessing Children's Implicit Attitudes Using the Affect Misattribution Procedure

ERIC Educational Resources Information Center

Williams, Amanda; Steele, Jennifer R.; Lipman, Corey

2016-01-01

In the current research, we examined whether the Affect Misattribution Procedure (AMP) could be successfully adapted as an implicit measure of children's attitudes. We tested this possibility in 3 studies with 5- to 10-year-old children. In Study 1, we found evidence that children misattribute affect elicited by attitudinally positive (e.g., cute…

The Search for Adult Assessment Procedures.

ERIC Educational Resources Information Center

Usnick, Virginia; Babbitt, Beatrice C.

1993-01-01

Reviewed 12 currently available mathematics assessment tools to determine whether they would be appropriate for use in a college-level mathematics clinic. Tests were assigned to two domains: cognitive and mathematical content. Major deficiencies of the tests are cited. (Contains 15 references.) (MDH)

Baseline and Verification Tests of the Electric Vehicle Associates’ Current Fare Station Wagon.

DTIC Science & Technology

1983-01-01

ELECTRIC Final Test Report VEICLE ASSOCIATES’CURRENT FARE STATION WAGON 27 March 1980 -6 November 1981 6. PERFORMING ORG. REPORT NUMBER * .7. AUTNOR(s) a...Whe,% Doe. Er(,rrrd) -I PREFACE Z..1~ The electric and hybrid vehicle test was conducted by the U.S. Army Mobility Equipment Research and Development...COAST-DOWN D. ELECTRIC AND HYBRID VEHICLE 92 VERIFICATION PROCEDURES 1".f S. -..°.o. . *-.. .,". .. " . ,. . . . . . . % % %d° ILLUSTRATIONS Figure

Shunt resistance and saturation current determination in CdTe and CIGS solar cells. Part 1: a new theoretical procedure and comparison with other methodologies

NASA Astrophysics Data System (ADS)

Rangel-Kuoppa, Victor-Tapio; Albor-Aguilera, María-de-Lourdes; Hérnandez-Vásquez, César; Flores-Márquez, José-Manuel; González-Trujillo, Miguel-Ángel; Contreras-Puente, Gerardo-Silverio

2018-04-01

A new proposal for the extraction of the shunt resistance (R sh ) and saturation current (I sat ) of a current-voltage (I-V) measurement of a solar cell, within the one-diode model, is given. First, the Cheung method is extended to obtain the series resistance (R s ), the ideality factor (n) and an upper limit for I sat . In this article which is Part 1 of two parts, two procedures are proposed to obtain fitting values for R sh and I sat within some voltage range. These two procedures are used in two simulated I-V curves (one in darkness and the other one under illumination) to recover the known solar cell parameters R sh , R s , n, I sat and the light current I lig and test its accuracy. The method is compared with two different common parameter extraction methods. These three procedures are used and compared in Part 2 in the I-V curves of CdS-CdTe and CIGS-CdS solar cells.

Round-robin testing of Soleq EV cort according to the SAE J1634 test procedure dated May 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cole, G.H.

1993-05-01

The Society of Automotive Engineers Recommended Practice, SAE J1634, {open_quotes}Electric Vehicle Energy Consumption and Range Test Procedure{close_quotes}, May 1993, describes a standard method of determining the range and energy consumption for electric vehicles. Consequent to the U.S. Department of Energy`s (DOE) rulemaking released on February 4, 1994, the EPA is currently considering factoring electric vehicles into the Corporate Average Fuel Economy (CAFE) calculations using the SAE J1634 procedure. The purpose of this project is to provide information regarding the suitability of this recommended practice for determining the energy economy value to be factored into the CAFE. Issues leading to possiblemore » inconsistent results (such as the repeatability of the procedure, thoroughness of the procedure`s methods, and variance between different laboratories using different dynamometers) need to be resolved prior to passing legislation which will mandate use of this test in determining the electric vehicle CAFE credit. To this end, separate tests were performed on a Soleq EVcort vehicle by the INEL, the EPA, Ford Motor Company, Southwest Research Institute, and the California Air Resources Board using their own facilities and personnel. Acceptable departures from the driving profile prescribed by SAEJ1634 are not well defined. This deficiency in the procedure is even more noticeable due to the EVcort`s marginal acceleration performance.« less

Tinnitus--Current Concepts in Diagnosis and Management.

ERIC Educational Resources Information Center

Epstein, Stephen

1997-01-01

This article discusses the causes of tinnitus, sound or noise in the ears or head without any external stimulation. Classification of tinnitus, the essentials of medical evaluation of a patient with tinnitus, essential test procedures, and current concepts in the management of tinnitus are addressed. (CR)

The Essay Scoring and Scorer Reliability in TOEFL CBT.

ERIC Educational Resources Information Center

Lee, Yong-Won

An essay test is now an integral part of the computer based Test of English as a Foreign Language (TOEFL-CBT). This paper provides a brief overview of the current TOEFL-CBT essay test, describes the operational procedures for essay scoring, including the Online Scoring Network (OSN) of the Educational Testing Service (ETS), and discusses major…

Mode II Interlaminar Fracture Toughness and Fatigue Characterization of a Graphite Epoxy Composite Material

NASA Technical Reports Server (NTRS)

O'Brien, T. Kevin; Johnston, William M.; Toland, Gregory J.

2010-01-01

Mode II interlaminar fracture toughness and delamination onset and growth characterization data were generated for IM7/8552 graphite epoxy composite materials from two suppliers for use in fracture mechanics analyses. Both the fracture toughness testing and the fatigue testing were conducted using the End-notched Flexure (ENF) test. The ENF test for mode II fracture toughness is currently under review by ASTM as a potential standard test method. This current draft ASTM protocol was used as a guide to conduct the tests on the IM7/8552 material. This report summarizes the test approach, methods, procedures and results of this characterization effort.

Gas electron multiplier (GEM) foil test, repair and effective gain calculation

NASA Astrophysics Data System (ADS)

Tahir, Muhammad; Zubair, Muhammad; Khan, Tufail A.; Khan, Ashfaq; Malook, Asad

2018-06-01

The focus of my research is based on the gas electron multiplier (GEM) foil test, repairing and effective gain calculation of GEM detector. During my research work define procedure of GEM foil testing short-circuit, detection short-circuits in the foil. Study different ways to remove the short circuits in the foils. Set and define the GEM foil testing procedures in the open air, and with nitrogen gas. Measure the leakage current of the foil and applying different voltages with specified step size. Define the Quality Control (QC) tests and different components of GEM detectors before assembly. Calculate the effective gain of GEM detectors using 109Cd and 55Fe radioactive source.

49 CFR Appendix C to Part 180 - Eddy Current Examination With Visual Inspection for DOT 3AL Cylinders Manufactured of Aluminum...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Eddy Current Examination With Visual Inspection... PACKAGINGS Pt. 180, App. C Appendix C to Part 180—Eddy Current Examination With Visual Inspection for DOT 3AL... procedure applicable to the test equipment it uses to perform eddy current examinations. 2. Visual...

A simple test procedure for evaluating low temperature crack resistance of asphalt concrete.

DOT National Transportation Integrated Search

2009-11-01

The current means of evaluating the low temperature cracking resistance of HMA relies on extensive test : methods that require assumptions about material behaviors and the use of complicated loading equipment. The purpose : of this study was to devel...

Development of a standard accelerated weathering test for aggregates using dimethyl sulfoxide (DMSO) : final report.

DOT National Transportation Integrated Search

1986-09-01

A standard accelerated weathering test using Dimethyl Sulfoxide (DMSO) was developed to simulate the chemical degradation of basaltic rocks. After a thorough study of the parameters affecting the current procedure, such as container geometry, aggrega...

Process for testing a xenon gas feed system of a hollow cathode assembly

NASA Technical Reports Server (NTRS)

Patterson, Michael J. (Inventor); Verhey, Timothy R. R. (Inventor); Soulas, George C. (Inventor)

2004-01-01

The design and manufacturing processes for Hollow Cathode Assemblies (HCA's) that operate over a broad range of emission currents up to 30 Amperes, at low potentials, with lifetimes in excess of 17,500 hours. The processes include contamination control procedures which cover hollow cathode component cleaning procedures, gas feed system designs and specifications, and hollow cathode activation and operating procedures to thereby produce cathode assemblies that have demonstrated stable and repeatable operating conditions, for both the discharge current and voltage. The HCA of this invention provides lifetimes of greater than 10,000 hours, and expected lifetimes of greater than 17,500 hours, whereas the present state-of-the-art is less than 500 hours at emission currents in excess of 1 Ampere. Stable operation is provided over a large range of operating emission currents, up to a 6:1 ratio, and this HCA can emit electron currents of up to 30 Amperes in magnitude to an external anode that simulates the current drawn to a space plasma, at voltages of less than 20 Volts.

77 FR 1129 - Revisions to Test Methods and Testing Regulations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-09

...This action proposes editorial and technical corrections necessary for source testing of emissions and operations. The revisions include the addition of alternative equipment and methods as well as corrections to technical and typographical errors. We also solicit public comment on potential changes to the current procedures for determining emission stratification.

75 FR 25224 - Energy Conservation Program for Commercial Equipment: Decision and Order Granting a Waiver to...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-07

... systems. As a condition of this waiver, Daikin must use the alternate test procedure set forth in this... systems contain design characteristics that prevent them from being tested using the current DOE test.... The VRV-III-C systems have operational characteristics similar to other commercial multi-split...

76 FR 17577 - Increased Scope of Coverage for Electric Motors

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-30

... motors do not include a full frame, front plate, bearings, shaft, or shaft support. Because the ability.... chosen, the efficiency of these motors is therefore dependent on the application. Because of this, they... face plate, and therefore can be tested with a ``dummy test bracket'' using the current test procedure...

Common Practice Lightning Strike Protection Characterization Technique to Quantify Damage Mechanisms on Composite Substrates

NASA Technical Reports Server (NTRS)

Szatkowski, George N.; Dudley, Kenneth L.; Koppen, Sandra V.; Ely, Jay J.; Nguyen, Truong X.; Ticatch, Larry A.; Mielnik, John J.; Mcneill, Patrick A.

2013-01-01

To support FAA certification airworthiness standards, composite substrates are subjected to lightning direct-effect electrical waveforms to determine performance characteristics of the lightning strike protection (LSP) conductive layers used to protect composite substrates. Test results collected from independent LSP studies are often incomparable due to variability in test procedures & applied practices at different organizations, which impairs performance correlations between different LSP data sets. Under a NASA supported contract, The Boeing Company developed technical procedures and documentation as guidance in order to facilitate a test method for conducting universal common practice lightning strike protection test procedures. The procedures obtain conformity in future lightning strike protection evaluations to allow meaningful performance correlations across data sets. This universal common practice guidance provides the manufacturing specifications to fabricate carbon fiber reinforced plastic (CFRP) test panels, including finish, grounding configuration, and acceptable methods for pretest nondestructive inspection (NDI) and posttest destructive inspection. The test operations guidance elaborates on the provisions contained in SAE ARP5416 to address inconsistencies in the generation of damage protection performance data, so as to provide for maximum achievable correlation across capable lab facilities. In addition, the guidance details a direct effects test bed design to aid in quantification of the multi-physical phenomena surrounding a lightning direct attachment supporting validation data requirements for the development of predictive computational modeling. The lightning test bed is designed to accommodate a repeatable installation procedure to secure the test panel and eliminate test installation uncertainty. It also facilitates a means to capture the electrical waveform parameters in 2 dimensions, along with the mechanical displacement and thermal heating parameters which occur during lightning attachment. Following guidance defined in the universal common practice LSP test documents, protected and unprotected CFRP panels were evaluated at 20, 40 and 100KAmps. This report presents analyzed data demonstrating the scientific usefulness of the common practice approach. Descriptions of the common practice CFRP test articles, LSP test bed fixture, and monitoring techniques to capture the electrical, mechanical and thermal parameters during lightning attachment are presented here. Two methods of measuring the electrical currents were evaluated, inductive current probes and a newly developed fiberoptic sensor. Two mechanical displacement methods were also examined, optical laser measurement sensors and a digital imaging correlation camera system. Recommendations are provided to help users implement the common practice test approach and obtain LSP test characterizations comparable across data sets.

Development of new test procedures for measuring fine and coarse aggregates specific gravity.

DOT National Transportation Integrated Search

2009-09-01

The objective of the research is to develop and evaluate new test methods at determining the specific gravity and absorption of both fine and coarse aggregates. Current methods at determining the specific gravity and absorption of fine and coarse agg...

Development of Transit Coach Bonded Brake Lining Test Equipment and Test Procedures--Progress Report

DOT National Transportation Integrated Search

1984-01-01

Bonded brake linings have been introduced in limited quantities at several urban and suburban transit properties. The in-service capabilities of current bonding processes and brake materials are undergoing assessment, and field data on the wear and f...

ADAPTING THE MEDAKA EMBRYO ASSAY TO A HIGH-THROUGHPUT APPROACH FOR DEVELOPMENTAL TOXICITY TESTING.

EPA Science Inventory

Chemical exposure during embryonic development may cause persistent effects, yet developmental toxicity data exist for very few chemicals. Current testing procedures are time consuming and costly, underlining the need for rapid and low cost screening strategies. While in vitro ...

Experience of 12 kA / 16 V SMPS during the HTS Current Leads Test

NASA Astrophysics Data System (ADS)

Panchal, P.; Christian, D.; Panchal, R.; Sonara, D.; Purwar, G.; Garg, A.; Nimavat, H.; Singh, G.; Patel, J.; Tanna, V.; Pradhan, S.

2017-04-01

As a part of up gradation plans in SST-1 Tokamak, one pair of 3.3 kA rated prototype hybrid current leads were developed using Di-BSCCO as High Temperature Superconductors (HTS) and the copper heat exchanger. In order to validate the manufacturing procedure prior to go for series production of such current leads, it was recommended to test these current leads using dedicated and very reliable DC switch mode power supply (SMPS). As part of test facility, 12 kA, 16 VDC programmable SMPS was successfully installed, commissioned and tested. This power supply has special features such as modularity, N+1 redundancy, very low ripple voltage, precise current measurements with Direct Current Current Transformer, CC/CV modes with auto-crossover and auto-sequence programming. As a part of acceptance of this converter, A 5.8 mΩ water-cooled resistive dummy load and PLC based SCADA system is designed, developed for commissioning of power supply. The same power supply was used for the testing of the prototype HTS current leads. The paper describes the salient features and experience of state-of-art of power supply and results obtained from this converter during the HTS current leads test.

Spaceport Command and Control System Automated Testing

NASA Technical Reports Server (NTRS)

Stein, Meriel

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administrations (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This large system requires high quality testing that will properly measure the capabilities of the system. Automating the test procedures would save the project time and money. Therefore, the Electrical Engineering Division at Kennedy Space Center (KSC) has recruited interns for the past two years to work alongside full-time engineers to develop these automated tests, as well as innovate upon the current automation process.

Spaceport Command and Control System Automation Testing

NASA Technical Reports Server (NTRS)

Hwang, Andrew

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administrations (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This large system requires high quality testing that will properly measure the capabilities of the system. Automating the test procedures would save the project time and money. Therefore, the Electrical Engineering Division at Kennedy Space Center (KSC) has recruited interns for the past two years to work alongside full-time engineers to develop these automated tests, as well as innovate upon the current automation process.

Rapid insulin sensitivity test (RIST).

PubMed

Lautt, W W; Wang, X; Sadri, P; Legare, D J; Macedo, M P

1998-12-01

A rapid insulin sensitivity test (RIST) was recently introduced to assess insulin action in vivo (H. Xie, L. Zhu, Y.L. Zhang, D.J. Legare, and W.W. Lautt. J. Pharmacol. Toxicol. Methods, 35: 77-82. 1996). This technical report describes the current recommended standard operating procedure for the use of the RIST in rats based upon additional experience with approximately 100 tests. We describe the manufacture and use of an arterial-venous shunt that allows rapid multiple arterial samples and intravenous administration of drugs. The RIST procedure involves determination of a stable arterial glucose baseline to define the ideal euglycemic level to be maintained following a 5-min infusion of insulin, with the RIST index being the amount of glucose required to be infused to maintain euglycemia over the test period. Insulin administration by a 5-min infusion is preferable to a 30-s bolus administration. No significant difference was determined between the use of Toronto pork-beef or human insulin. Four consecutive RISTs were carried out in the same animal over 4-5 h with no tendency for change with time. The RIST index is sufficiently sensitive and reproducible to permit establishment of insulin dose-response curves and interference of insulin action by elimination of hepatic parasympathetic nerves, using atropine. This technical report provides the current recommended standard operating procedure for the RIST.

A Measurement Plane for Optical Networks to Manage Emergency Events

NASA Astrophysics Data System (ADS)

Tego, E.; Carciofi, C.; Grazioso, P.; Petrini, V.; Pompei, S.; Matera, F.; Attanasio, V.; Nastri, E.; Restuccia, E.

2017-11-01

In this work, we show a wide geographical area optical network test bed, adopting the mPlane measurement plane for monitoring its performance and to manage software defined network approaches, with some specific tests and procedures dedicated to respond to disaster events and to support emergency networks. Such a test bed includes FTTX accesses, and it is currently implemented to support future 5G wireless services with slicing procedures based on Carrier Ethernet. The characteristics of this platform have been experimentally tested in the case of a damage-causing link failure and traffic congestion, showing a fast reactions to these disastrous events, allowing the user to recharge the initial QoS parameters.

Bioaccumulation of toxic substances associated with dredging and dredged material disposal: a literature review

USGS Publications Warehouse

Seelye, James G.; Mac, Michael J.

1984-01-01

A literature review of sediment bioassessment was conducted as the first step in the development of a more standardized and ecologically sound test procedure for evaluating sediment quality. Based on the review, the authors concluded that 1) a standardized laboratory bioassessment test should consist of flowthrough exposure of at least 10 days duration using more than one aquatic organism including at least an infaunal benthic invertebrate and a fish species. 2) Before adoption of a laboratory sediment bioassessment procedure, the laboratory results should be evaluated by comparison with field conditions. 3) Most current sediment bioassessment regulatory tests measure acute toxicity or bioaccumulation. Development of tests to evaluate chronic, sublethal effects is needed.

Sleeve Expansion of Bolt Holes in Railroad Rail : Volume II, Process Parameters and Procedures

DOT National Transportation Integrated Search

1980-02-01

The bolt-hole cold-expansion process has been applied to railroad rail in laboratory tests and has demonstrated a potential for the reduction of rail-bolt-hole-failure incidence. Limited field tests also have been conducted and are currently under lo...

75 FR 4823 - Proposed Data Collections Submitted for Public Comment and Recommendations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-29

... Prevention (CDC). Background and Brief Description Colorectal cancer (CRC) is the second leading cause of... procedures currently recommended as colorectal cancer screening tests, provide direct visualization of the... early cancers. Both of these tests require specialized training. Flexible sigmoidoscopy provides a view...

Variability in the Use of Simulation for Procedural Training in Radiology Residency: Opportunities for Improvement.

PubMed

Matalon, Shanna A; Chikarmane, Sona A; Yeh, Eren D; Smith, Stacy E; Mayo-Smith, William W; Giess, Catherine S

2018-03-19

Increased attention to quality and safety has led to a re-evaluation of the classic apprenticeship model for procedural training. Many have proposed simulation as a supplementary teaching tool. The purpose of this study was to assess radiology resident exposure to procedural training and procedural simulation. An IRB-exempt online survey was distributed to current radiology residents in the United States by e-mail. Survey results were summarized using frequency and percentages. Chi-square tests were used for statistical analysis where appropriate. A total of 353 current residents completed the survey. 37% (n = 129/353) of respondents had never used procedure simulation. Of the residents who had used simulation, most did not do so until after having already performed procedures on patients (59%, n = 132/223). The presence of a dedicated simulation center was reported by over half of residents (56%, n = 196/353) and was associated with prior simulation experience (P = 0.007). Residents who had not had procedural simulation were somewhat likely or highly likely (3 and 4 on a 4-point Likert-scale) to participate if it were available (81%, n = 104/129). Simulation training was associated with higher comfort levels in performing procedures (P < 0.001). Although procedural simulation training is associated with higher comfort levels when performing procedures, there is variable use in radiology resident training and its use is not currently optimized. Given the increased emphasis on patient safety, these results suggest the need to increase procedural simulation use during residency, including an earlier introduction to simulation before patient exposure. Copyright © 2018 Elsevier Inc. All rights reserved.

Operator procedure verification with a rapidly reconfigurable simulator

NASA Technical Reports Server (NTRS)

Iwasaki, Yumi; Engelmore, Robert; Fehr, Gary; Fikes, Richard

1994-01-01

Generating and testing procedures for controlling spacecraft subsystems composed of electro-mechanical and computationally realized elements has become a very difficult task. Before a spacecraft can be flown, mission controllers must envision a great variety of situations the flight crew may encounter during a mission and carefully construct procedures for operating the spacecraft in each possible situation. If, despite extensive pre-compilation of control procedures, an unforeseen situation arises during a mission, the mission controller must generate a new procedure for the flight crew in a limited amount of time. In such situations, the mission controller cannot systematically consider and test alternative procedures against models of the system being controlled, because the available simulator is too large and complex to reconfigure, run, and analyze quickly. A rapidly reconfigurable simulation environment that can execute a control procedure and show its effects on system behavior would greatly facilitate generation and testing of control procedures both before and during a mission. The How Things Work project at Stanford University has developed a system called DME (Device Modeling Environment) for modeling and simulating the behavior of electromechanical devices. DME was designed to facilitate model formulation and behavior simulation of device behavior including both continuous and discrete phenomena. We are currently extending DME for use in testing operator procedures, and we have built a knowledge base for modeling the Reaction Control System (RCS) of the space shuttle as a testbed. We believe that DME can facilitate design of operator procedures by providing mission controllers with a simulation environment that meets all these requirements.

Recent Achievements of the Collaboratory for the Study of Earthquake Predictability

NASA Astrophysics Data System (ADS)

Jordan, T. H.; Liukis, M.; Werner, M. J.; Schorlemmer, D.; Yu, J.; Maechling, P. J.; Jackson, D. D.; Rhoades, D. A.; Zechar, J. D.; Marzocchi, W.

2016-12-01

The Collaboratory for the Study of Earthquake Predictability (CSEP) supports a global program to conduct prospective earthquake forecasting experiments. CSEP testing centers are now operational in California, New Zealand, Japan, China, and Europe with 442 models under evaluation. The California testing center, started by SCEC, Sept 1, 2007, currently hosts 30-minute, 1-day, 3-month, 1-year and 5-year forecasts, both alarm-based and probabilistic, for California, the Western Pacific, and worldwide. Our tests are now based on the hypocentral locations and magnitudes of cataloged earthquakes, but we plan to test focal mechanisms, seismic hazard models, ground motion forecasts, and finite rupture forecasts as well. We have increased computational efficiency for high-resolution global experiments, such as the evaluation of the Global Earthquake Activity Rate (GEAR) model, introduced Bayesian ensemble models, and implemented support for non-Poissonian simulation-based forecasts models. We are currently developing formats and procedures to evaluate externally hosted forecasts and predictions. CSEP supports the USGS program in operational earthquake forecasting and a DHS project to register and test external forecast procedures from experts outside seismology. We found that earthquakes as small as magnitude 2.5 provide important information on subsequent earthquakes larger than magnitude 5. A retrospective experiment for the 2010-2012 Canterbury earthquake sequence showed that some physics-based and hybrid models outperform catalog-based (e.g., ETAS) models. This experiment also demonstrates the ability of the CSEP infrastructure to support retrospective forecast testing. Current CSEP development activities include adoption of the Comprehensive Earthquake Catalog (ComCat) as an authorized data source, retrospective testing of simulation-based forecasts, and support for additive ensemble methods. We describe the open-source CSEP software that is available to researchers as they develop their forecast models. We also discuss how CSEP procedures are being adapted to intensity and ground motion prediction experiments as well as hazard model testing.

Test/score/report: Simulation techniques for automating the test process

NASA Technical Reports Server (NTRS)

Hageman, Barbara H.; Sigman, Clayton B.; Koslosky, John T.

1994-01-01

A Test/Score/Report capability is currently being developed for the Transportable Payload Operations Control Center (TPOCC) Advanced Spacecraft Simulator (TASS) system which will automate testing of the Goddard Space Flight Center (GSFC) Payload Operations Control Center (POCC) and Mission Operations Center (MOC) software in three areas: telemetry decommutation, spacecraft command processing, and spacecraft memory load and dump processing. Automated computer control of the acceptance test process is one of the primary goals of a test team. With the proper simulation tools and user interface, the task of acceptance testing, regression testing, and repeatability of specific test procedures of a ground data system can be a simpler task. Ideally, the goal for complete automation would be to plug the operational deliverable into the simulator, press the start button, execute the test procedure, accumulate and analyze the data, score the results, and report the results to the test team along with a go/no recommendation to the test team. In practice, this may not be possible because of inadequate test tools, pressures of schedules, limited resources, etc. Most tests are accomplished using a certain degree of automation and test procedures that are labor intensive. This paper discusses some simulation techniques that can improve the automation of the test process. The TASS system tests the POCC/MOC software and provides a score based on the test results. The TASS system displays statistics on the success of the POCC/MOC system processing in each of the three areas as well as event messages pertaining to the Test/Score/Report processing. The TASS system also provides formatted reports documenting each step performed during the tests and the results of each step. A prototype of the Test/Score/Report capability is available and currently being used to test some POCC/MOC software deliveries. When this capability is fully operational it should greatly reduce the time necessary to test a POCC/MOC software delivery, as well as improve the quality of the test process.

Instruments for the nondestructive testing of materials and products: Handbook. Volumes 1 & 2 (2nd revised and enlarged edition)

NASA Astrophysics Data System (ADS)

Kliuev, V. V.

Data on the general design and principles of operation of various instruments and systems for the nondestructive testing of materials and products of various kinds are presented, and test procedures are described. Methods discussed include optical, thermal, capillary, RF, and X-ray testing techniques. The discussion also covers magnetic, electromagnetic, eddy-current, acoustic, and combined nondestructive testing methods.

Recent Achievements of the Collaboratory for the Study of Earthquake Predictability

NASA Astrophysics Data System (ADS)

Jackson, D. D.; Liukis, M.; Werner, M. J.; Schorlemmer, D.; Yu, J.; Maechling, P. J.; Zechar, J. D.; Jordan, T. H.

2015-12-01

Maria Liukis, SCEC, USC; Maximilian Werner, University of Bristol; Danijel Schorlemmer, GFZ Potsdam; John Yu, SCEC, USC; Philip Maechling, SCEC, USC; Jeremy Zechar, Swiss Seismological Service, ETH; Thomas H. Jordan, SCEC, USC, and the CSEP Working Group The Collaboratory for the Study of Earthquake Predictability (CSEP) supports a global program to conduct prospective earthquake forecasting experiments. CSEP testing centers are now operational in California, New Zealand, Japan, China, and Europe with 435 models under evaluation. The California testing center, operated by SCEC, has been operational since Sept 1, 2007, and currently hosts 30-minute, 1-day, 3-month, 1-year and 5-year forecasts, both alarm-based and probabilistic, for California, the Western Pacific, and worldwide. We have reduced testing latency, implemented prototype evaluation of M8 forecasts, and are currently developing formats and procedures to evaluate externally-hosted forecasts and predictions. These efforts are related to CSEP support of the USGS program in operational earthquake forecasting and a DHS project to register and test external forecast procedures from experts outside seismology. A retrospective experiment for the 2010-2012 Canterbury earthquake sequence has been completed, and the results indicate that some physics-based and hybrid models outperform purely statistical (e.g., ETAS) models. The experiment also demonstrates the power of the CSEP cyberinfrastructure for retrospective testing. Our current development includes evaluation strategies that increase computational efficiency for high-resolution global experiments, such as the evaluation of the Global Earthquake Activity Rate (GEAR) model. We describe the open-source CSEP software that is available to researchers as they develop their forecast models (http://northridge.usc.edu/trac/csep/wiki/MiniCSEP). We also discuss applications of CSEP infrastructure to geodetic transient detection and how CSEP procedures are being adapted to ground motion prediction experiments.

A Statistical Procedure for Testing Unusually Frequent Exactly Matching Responses and Nearly Matching Responses. Research Report. ETS RR-17-23

ERIC Educational Resources Information Center

Haberman, Shelby J.; Lee, Yi-Hsuan

2017-01-01

In investigations of unusual testing behavior, a common question is whether a specific pattern of responses occurs unusually often within a group of examinees. In many current tests, modern communication techniques can permit quite large numbers of examinees to share keys, or common response patterns, to the entire test. To address this issue,…

Assessment of Second Language Performance.

ERIC Educational Resources Information Center

Lumley, Tom

1996-01-01

A discussion of current second language testing trends and practices in Australia focuses on the use of performance assessment, providing examples of its application in four specific contexts: an occupational English test used for to assess job-related English language skills as part of the certification procedure for health professionals;…

Three studies of biographical factors associated with success in air traffic control specialist screening/training at the FAA Academy.

DOT National Transportation Integrated Search

1983-04-01

The current Air Traffic Control Specialist (ATCS) selection procedure requires that all applicants pass the Office of Personnel Management (OPM) air traffic control aptitude test. In addition to the test scores, applicants may also receive points for...

Intellectual Assessment of Children and Adolescents: The Case of Greece

ERIC Educational Resources Information Center

Bablekou, Zoe; Kazi, Smaragda

2016-01-01

The article reviews the history of intellectual assessment of children and adolescents in Greece, as well as procedures, current practices, and future directions. Although the history of special education is long in Greece, there has been very sporadic and incoherent legislation and decision making on the subject. Currently, intelligence tests are…

242A Distributed Control System Year 2000 Acceptance Test Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

TEATS, M.C.

1999-08-31

This report documents acceptance test results for the 242-A Evaporator distributive control system upgrade to D/3 version 9.0-2 for year 2000 compliance. This report documents the test results obtained by acceptance testing as directed by procedure HNF-2695. This verification procedure will document the initial testing and evaluation of the potential 242-A Distributed Control System (DCS) operating difficulties across the year 2000 boundary and the calendar adjustments needed for the leap year. Baseline system performance data will be recorded using current, as-is operating system software. Data will also be collected for operating system software that has been modified to correct yearmore » 2000 problems. This verification procedure is intended to be generic such that it may be performed on any D/3{trademark} (GSE Process Solutions, Inc.) distributed control system that runs with the VMSTM (Digital Equipment Corporation) operating system. This test may be run on simulation or production systems depending upon facility status. On production systems, DCS outages will occur nine times throughout performance of the test. These outages are expected to last about 10 minutes each.« less

Vehicle Test Procedure Driving Schedules

DOT National Transportation Integrated Search

1977-03-01

This report discusses the salient characteristics of driving schedules which are currently being used to determine automotive fuel economy, exhaust emissions, and component characteristics. The analyses discussed and the results reported highlight th...

The Case for Laboratory Developed Procedures

PubMed Central

Sabatini, Linda M.; Tsongalis, Gregory J.; Caliendo, Angela M.; Olsen, Randall J.; Ashwood, Edward R.; Bale, Sherri; Benirschke, Robert; Carlow, Dean; Funke, Birgit H.; Grody, Wayne W.; Hayden, Randall T.; Hegde, Madhuri; Lyon, Elaine; Pessin, Melissa; Press, Richard D.; Thomson, Richard B.

2017-01-01

An explosion of knowledge and technology is revolutionizing medicine and patient care. Novel testing must be brought to the clinic with safety and accuracy, but also in a timely and cost-effective manner, so that patients can benefit and laboratories can offer testing consistent with current guidelines. Under the oversight provided by the Clinical Laboratory Improvement Amendments, laboratories have been able to develop and optimize laboratory procedures for use in-house. Quality improvement programs, interlaboratory comparisons, and the ability of laboratories to adjust assays as needed to improve results, utilize new sample types, or incorporate new mutations, information, or technologies are positive aspects of Clinical Laboratory Improvement Amendments oversight of laboratory-developed procedures. Laboratories have a long history of successful service to patients operating under Clinical Laboratory Improvement Amendments. A series of detailed clinical examples illustrating the quality and positive impact of laboratory-developed procedures on patient care is provided. These examples also demonstrate how Clinical Laboratory Improvement Amendments oversight ensures accurate, reliable, and reproducible testing in clinical laboratories. PMID:28815200

Pixelated Geiger-Mode Avalanche Photo-Diode Characterization Through Dark Current Measurement

NASA Astrophysics Data System (ADS)

Amaudruz, Pierre-Andre; Bishop, Daryl; Gilhully, Colleen; Goertzen, Andrew; James, Lloyd; Kozlowski, Piotr; Retiere, Fabrice; Shams, Ehsan; Sossi, Vesna; Stortz, Greg; Thiessen, Jonathan D.; Thompson, Christopher J.

2014-06-01

PIXELATED geiger-mode avalanche photodiodes (PPDs), often called silicon photomultipliers (SiPMs) are emerging as an excellent replacement for traditional photomultiplier tubes (PMTs) in a variety of detectors, especially those for subatomic physics experiments, which requires extensive test and operation procedures in order to achieve uniform responses from all the devices. In this paper, we show for two PPD brands, Hamamatsu MPPC and SensL SPM, that at room temperature, the dark noise rate, breakdown voltage and rate of correlated avalanches can be inferred from the sole measure of dark current as a function of operating voltage, hence greatly simplifying the characterization procedure. We introduce a custom electronics system that allows measurement for many devices concurrently, hence allowing rapid testing and monitoring of many devices at low cost. Finally, we show that the dark current of Hamamastu Multi-Pixel Photon Counter (MPPC) is rather independent of temperature at constant operating voltage, hence the current measure cannot be used to probe temperature variations. On the other hand, the MPPC current can be used to monitor light source conditions in DC mode without requiring strong temperature stability, as long as the integrated source brightness is comparable to the dark noise rate.

sFlt-1/PlGF ratio test for pre-eclampsia: an economic assessment for the UK.

PubMed

Vatish, M; Strunz-McKendry, T; Hund, M; Allegranza, D; Wolf, C; Smare, C

2016-12-01

To assess the economic impact of introducing into clinical practice in the UK the soluble fms-like tyrosine kinase (sFlt-1) to placental growth factor (PlGF) ratio test for guiding the management of pre-eclampsia. We used an economic model estimating the incremental value of information, from a UK National Health Service payer's perspective, generated by the sFlt-1/PlGF ratio test, compared with current diagnostic procedures, in guiding the management of women with suspected pre-eclampsia. The economic model estimated costs associated with the diagnosis and management of pre-eclampsia in pregnant women between 24 + 0 and 36 + 6 weeks' gestation, managed in either a 'test' scenario in which the sFlt-1/PlGF test is used in addition to current diagnostic procedures, or a 'no-test' scenario in which clinical decisions are based on current diagnostic procedures alone. Test characteristics and resource use were derived from PROGNOSIS, a non-interventional study in women presenting with clinical suspicion of pre-eclampsia. The main outcome measure from the economic model was the cost per patient per episode of care, from first suspicion of pre-eclampsia to birth. Introduction of the sFlt-1/PlGF ratio test into clinical practice is expected to result in cost savings of £344 per patient compared with a no-test scenario. Savings are generated primarily through an improvement in diagnostic accuracy and subsequent reduction in unnecessary hospitalization. Introducing the sFlt-1/PlGF ratio test into clinical practice in the UK was shown to be cost-saving by reducing unnecessary hospitalization of women at low risk of developing pre-eclampsia. In addition, the test ensures that those women at higher risk are identified and managed appropriately. © 2016 Authors. Ultrasound in Obstetrics & Gynecology published by John Wiley & Sons Ltd on behalf of International Society of Ultrasound in Obstetrics and Gynecology. © 2016 The Authors. Ultrasound in Obstetrics & Gynecology published by John Wiley & Sons Ltd on behalf of the International Society of Ultrasound in Obstetrics and Gynecology.

Mechanistic flexible pavement overlay design program.

DOT National Transportation Integrated Search

2009-07-01

The current Louisiana Department of Transportation and Development (LADOTD) overlay thickness design method follows the Component : Analysis procedure provided in the 1993 AASHTO pavement design guide. Since neither field nor laboratory tests a...

Seismic design verification of LMFBR structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1977-07-01

The report provides an assessment of the seismic design verification procedures currently used for nuclear power plant structures, a comparison of dynamic test methods available, and conclusions and recommendations for future LMFB structures.

An assembly-type master-slave catheter and guidewire driving system for vascular intervention.

PubMed

Cha, Hyo-Jeong; Yi, Byung-Ju; Won, Jong Yun

2017-01-01

Current vascular intervention inevitably exposes a large amount of X-ray to both an operator and a patient during the procedure. The purpose of this study is to propose a new catheter driving system which assists the operator in aspects of less X-ray exposure and convenient user interface. For this, an assembly-type 4-degree-of-freedom master-slave system was designed and tested to verify the efficiency. First, current vascular intervention procedures are analyzed to develop a new robotic procedure that enables us to use conventional vascular intervention devices such as catheter and guidewire which are commercially available in the market. Some parts of the slave robot which contact the devices were designed to be easily assembled and dissembled from the main body of the slave robot for sterilization. A master robot is compactly designed to conduct insertion and rotational motion and is able to switch from the guidewire driving mode to the catheter driving mode or vice versa. A phantom resembling the human arteries was developed, and the master-slave robotic system is tested using the phantom. The contact force of the guidewire tip according to the shape of the arteries is measured and reflected to the user through the master robot during the phantom experiment. This system can drastically reduce radiation exposure by replacing human effort by a robotic system for high radiation exposure procedures. Also, benefits of the proposed robot system are low cost by employing currently available devices and easy human interface.

Issues in the Educational, Psychological Assessment of Visually Impaired Children: Test-Retest Reliability of the Williams Intelligence Test for Children with Defective Vision

ERIC Educational Resources Information Center

Tobin, Michael J.; Hill, Eileen W.

2011-01-01

The article discusses some problems confronting teachers and psychologists when making decisions as to how to use the currently available test procedures. It reports data gathered on three separate occasions on the performance of a group of blind and partially sighted children on the Williams Intelligence Test which is the only specialist IQ test…

Nondestructive examination of the Tropical Rainfall Measuring Mission (TRMM) reaction control subsystem (RCS) propellant tanks

NASA Technical Reports Server (NTRS)

Free, James M.

1993-01-01

This paper assesses the feasibility of using eddy current nondestructive examination to determine flaw sizes in completely assembled hydrazine propellant tanks. The study was performed by the NASA Goddard Space Flight Center for the Tropical Rainfall Measuring Mission (TRMM) project to help determine whether existing propellant tanks could meet the fracture analysis requirements of the current pressure vessel specification, MIL-STD-1522A and, therefore be used on the TRMM spacecraft. After evaluating several nondestructive test methods, eddy current testing was selected as the most promising method for determining flaw sizes on external and internal surfaces of completely assembled tanks. Tests were conducted to confirm the detection capability of the eddy current NDE, procedures were developed to inspect two candidate tanks, and the test support equipment was designed. The non-spherical tank eddy current NDE test program was terminated when the decision was made to procure new tanks for the TRMM propulsion subsystem. The information on the development phase of this test program is presented in this paper as a reference for future investigation on the subject.

Evaluating the Emergency Notification Systems of the NASA White Sands Test

NASA Technical Reports Server (NTRS)

Chavez, Alfred Paul

2004-01-01

The problem was that the NASA Fire and Emergency Services did not know if the current emergency notification systems on the NASA White Sands Test Facility were appropriate for alerting the employees of an emergency. The purpose of this Applied Research Project was to determine if the current emergency notification systems of the White Sands Test Facility are appropriate for alerting the employees of an emergency. This was a descriptive research project. The research questions were: 1) What are similar facilities using to alert the employees of an emergency?; 2) Are the current emergency notification systems suitable for the community hazards on the NASA White Sands Test Facility?; 3) What is the NASA Fire and Emergency Services currently using to measure the effectiveness of the emergency notification systems?; and 4) What are the current training methods used to train personnel to the emergency notification systems at the NASA White Sands Test Facility? The procedures involved were to research other established facilities, research published material from credible sources, survey the facility to determine the facility perception of the emergency notification systems, and evaluate the operating elements of the established emergency notification systems for the facility. The results were that the current systems are suitable for the type of hazards the facility may endure. The emergency notification systems are tested frequently to ensure effectiveness in the event of an emergency. Personnel are trained and participate in a yearly drill to make certain personnel are educated on the established systems. The recommendations based on the results were to operationally improve the existing systems by developing and implementing one system that can overall notify the facility of a hazard. Existing procedures and training should also be improved to ensure that all personnel are educated on what to do when the emergency notification systems are activated.

An optimized implementation of a fault-tolerant clock synchronization circuit

NASA Technical Reports Server (NTRS)

Torres-Pomales, Wilfredo

1995-01-01

A fault-tolerant clock synchronization circuit was designed and tested. A comparison to a previous design and the procedure followed to achieve the current optimization are included. The report also includes a description of the system and the results of tests performed to study the synchronization and fault-tolerant characteristics of the implementation.

An Investigation of Sample Size Splitting on ATFIND and DIMTEST

ERIC Educational Resources Information Center

Socha, Alan; DeMars, Christine E.

2013-01-01

Modeling multidimensional test data with a unidimensional model can result in serious statistical errors, such as bias in item parameter estimates. Many methods exist for assessing the dimensionality of a test. The current study focused on DIMTEST. Using simulated data, the effects of sample size splitting for use with the ATFIND procedure for…

76 FR 33271 - Energy Conservation Program for Consumer Products: Decision and Order Granting a Waiver to...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

... authorizes the Secretary of Energy to prescribe test procedures that are reasonably designed to produce... conditions is met: (1) The petitioner's basic model contains one or more design characteristics that prevent..., BSH asserts, design characteristics of these models prevent testing according to the currently...

29 CFR 1630.3 - Exceptions to the definitions of “Disability” and “Qualified Individual with a Disability.”

Code of Federal Regulations, 2014 CFR

2014-07-01

... procedures, including but not limited to drug testing, designed to ensure that an individual described in...) Drug testing). (d) Disability does not include: (1) Transvestism, transsexualism, pedophilia... do not include individuals currently engaging in the illegal use of drugs, when the covered entity...

29 CFR 1630.3 - Exceptions to the definitions of “Disability” and “Qualified Individual with a Disability.”

Code of Federal Regulations, 2013 CFR

2013-07-01

... procedures, including but not limited to drug testing, designed to ensure that an individual described in...) Drug testing). (d) Disability does not include: (1) Transvestism, transsexualism, pedophilia... do not include individuals currently engaging in the illegal use of drugs, when the covered entity...

29 CFR 1630.3 - Exceptions to the definitions of “Disability” and “Qualified Individual with a Disability.”

Code of Federal Regulations, 2010 CFR

2010-07-01

... procedures, including but not limited to drug testing, designed to ensure that an individual described in...) Drug testing). (d) Disability does not include: (1) Transvestism, transsexualism, pedophilia... do not include individuals currently engaging in the illegal use of drugs, when the covered entity...

29 CFR 1630.3 - Exceptions to the definitions of “Disability” and “Qualified Individual with a Disability.”

Code of Federal Regulations, 2011 CFR

2011-07-01

... procedures, including but not limited to drug testing, designed to ensure that an individual described in...) Drug testing). (d) Disability does not include: (1) Transvestism, transsexualism, pedophilia... do not include individuals currently engaging in the illegal use of drugs, when the covered entity...

29 CFR 1630.3 - Exceptions to the definitions of “Disability” and “Qualified Individual with a Disability.”

Code of Federal Regulations, 2012 CFR

2012-07-01

... procedures, including but not limited to drug testing, designed to ensure that an individual described in...) Drug testing). (d) Disability does not include: (1) Transvestism, transsexualism, pedophilia... do not include individuals currently engaging in the illegal use of drugs, when the covered entity...

Single-Word Intelligibility in Speakers with Repaired Cleft Palate

ERIC Educational Resources Information Center

Whitehill, Tara; Chau, Cynthia

2004-01-01

Many speakers with repaired cleft palate have reduced intelligibility, but there are limitations with current procedures for assessing intelligibility. The aim of this study was to construct a single-word intelligibility test for speakers with cleft palate. The test used a multiple-choice identification format, and was based on phonetic contrasts…

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XVII, LEARNING ABOUT AC GENERATOR (ALTERNATOR) PRINCIPLES (PART II).

ERIC Educational Resources Information Center

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATING PRINCIPLES AND THE SERVICING AND TESTING PROCEDURES FOR ALTERNATING CURRENT (AC) GENERATORS AND REGULATORS USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE REVIEW OF ALTERNATOR PRINCIPLES, ALTERNATOR SERVICING AND TESTING, ALTERNATOR REGULATOR OPERATING…

Application of historical mobility testing to sensor-based robotic performance

NASA Astrophysics Data System (ADS)

Willoughby, William E.; Jones, Randolph A.; Mason, George L.; Shoop, Sally A.; Lever, James H.

2006-05-01

The USA Engineer Research and Development Center (ERDC) has conducted on-/off-road experimental field testing with full-sized and scale-model military vehicles for more than fifty years. Some 4000 acres of local terrain are available for tailored field evaluations or verification/validation of future robotic designs in a variety of climatic regimes. Field testing and data collection procedures, as well as techniques for quantifying terrain in engineering terms, have been developed and refined into algorithms and models for predicting vehicle-terrain interactions and resulting forces or speeds of military-sized vehicles. Based on recent experiments with Matilda, Talon, and Pacbot, these predictive capabilities appear to be relevant to most robotic systems currently in development. Utilization of current testing capabilities with sensor-based vehicle drivers, or use of the procedures for terrain quantification from sensor data, would immediately apply some fifty years of historical knowledge to the development, refinement, and implementation of future robotic systems. Additionally, translation of sensor-collected terrain data into engineering terms would allow assessment of robotic performance a priori deployment of the actual system and ensure maximum system performance in the theater of operation.

Development of a High Accuracy Angular Measurement System for Langley Research Center Hypersonic Wind Tunnel Facilities

NASA Technical Reports Server (NTRS)

Newman, Brett; Yu, Si-bok; Rhew, Ray D. (Technical Monitor)

2003-01-01

Modern experimental and test activities demand innovative and adaptable procedures to maximize data content and quality while working within severely constrained budgetary and facility resource environments. This report describes development of a high accuracy angular measurement capability for NASA Langley Research Center hypersonic wind tunnel facilities to overcome these deficiencies. Specifically, utilization of micro-electro-mechanical sensors including accelerometers and gyros, coupled with software driven data acquisition hardware, integrated within a prototype measurement system, is considered. Development methodology addresses basic design requirements formulated from wind tunnel facility constraints and current operating procedures, as well as engineering and scientific test objectives. Description of the analytical framework governing relationships between time dependent multi-axis acceleration and angular rate sensor data and the desired three dimensional Eulerian angular state of the test model is given. Calibration procedures for identifying and estimating critical parameters in the sensor hardware is also addressed.

EMU processing - A myth dispelled

NASA Technical Reports Server (NTRS)

Peacock, Paul R.; Wilde, Richard C.; Lutz, Glenn C.; Melgares, Michael A.

1991-01-01

The refurbishment-and-checkout 'processing' activities entailed by the Space Shuttle Extravehicular Mobility Units (EMUs) are currently significantly more modest, at 1050 man-hours, than when Space Shuttle services began (involving about 4000 man-hours). This great improvement in hardware efficiency is due to the design or modification of test rigs for simplification of procedures, as well as those procedures' standardization, in conjunction with an increase in hardware confidence which has allowed the extension of inspection, service, and testing intervals. Recent simplification of the hardware-processing sequence could reduce EMU processing requirements to 600 man-hours in the near future.

Solid State Power Controller Fuse Development Program.

DTIC Science & Technology

1983-10-01

4NYP Appendix A nic =,-, ’XW LX, nII4CD1AFam" CC,’AP44 257-290 TABLE I - FAULT CURRENT TRIP TJMWS Fa’ Ii AC Volts Seconds Rema:ks 1. 1.6 100Z 234.0 417.0...calibration date: 12 July 1983 Biddle Power Rheostat, 1000 W, Cat. No. 20 4.2 Procedure Testing was accomplished in two lots, one consisting of the SPC-2A and...Last calibration date: 12 July 1983 Biddle 100dW Power Rheostat, Cat. No. 20 Variac, Environ No. 380-503 4.2 Procedure The test specimens were suspended

Automated Road Closure Gate

DOT National Transportation Integrated Search

2000-05-01

This report presents the procedures involved in the research, design, construction, and testing of an Automated Road Closure Gate. The current road closure gates used in South Dakota are often unsafe and difficult to operate. This report will assist ...

Electrical resistivity measurement of mechanically stabilized Earth wall backfill : technical summary.

DOT National Transportation Integrated Search

2016-06-01

In Kansas, mechanically stabilized earth (MSE) retaining walls are typically : backfilled with coarse aggregate. Current backfill material testing procedures used : by the Kansas Department of Transportation (KDOT) utilize on-site observations for : ...

Continuing challenges for computer-based neuropsychological tests.

PubMed

Letz, Richard

2003-08-01

A number of issues critical to the development of computer-based neuropsychological testing systems that remain continuing challenges to their widespread use in occupational and environmental health are reviewed. Several computer-based neuropsychological testing systems have been developed over the last 20 years, and they have contributed substantially to the study of neurologic effects of a number of environmental exposures. However, many are no longer supported and do not run on contemporary personal computer operating systems. Issues that are continuing challenges for development of computer-based neuropsychological tests in environmental and occupational health are discussed: (1) some current technological trends that generally make test development more difficult; (2) lack of availability of usable speech recognition of the type required for computer-based testing systems; (3) implementing computer-based procedures and tasks that are improvements over, not just adaptations of, their manually-administered predecessors; (4) implementing tests of a wider range of memory functions than the limited range now available; (5) paying more attention to motivational influences that affect the reliability and validity of computer-based measurements; and (6) increasing the usability of and audience for computer-based systems. Partial solutions to some of these challenges are offered. The challenges posed by current technological trends are substantial and generally beyond the control of testing system developers. Widespread acceptance of the "tablet PC" and implementation of accurate small vocabulary, discrete, speaker-independent speech recognition would enable revolutionary improvements to computer-based testing systems, particularly for testing memory functions not covered in existing systems. Dynamic, adaptive procedures, particularly ones based on item-response theory (IRT) and computerized-adaptive testing (CAT) methods, will be implemented in new tests that will be more efficient, reliable, and valid than existing test procedures. These additional developments, along with implementation of innovative reporting formats, are necessary for more widespread acceptance of the testing systems.

[Do Current German-Language Intelligence Tests Take into Consideration the Special Needs of Children with Disabilities?].

PubMed

Mickley, Manfred; Renner, Gerolf

2015-01-01

Do Current German-Language Intelligence Tests Take into Consideration the Special Needs of Children with Disabilities? A review of 23 German intelligence test manuals shows that test-authors do not exclude the use of their tests for children with disabilities. However, these special groups play a minor role in the construction, standardization, and validation of intelligence tests. There is no sufficient discussion and reflection concerning the issue which construct-irrelevant requirements may reduce the validity of the test or which individual test-adaptations are allowed or recommended. Intelligence testing of children with disabilities needs more empirical evidence on objectivity, reliability, and validity of the assessment-procedures employed. Future test construction and validation should systematically analyze construct-irrelevant variance in item format, the special needs of handicapped children, and should give hints for useful test-adaptations.

Chewability testing in the development of a chewable tablet for hyperphosphatemia.

PubMed

Lanz, Michael; Baldischweiler, Jan; Kriwet, Burkhard; Schill, Jutta; Stafford, John; Imanidis, Georgios

2014-12-01

The official Pharmacopeia does not include a test procedure for the in vitro estimation of the chewability of tablets and publications in the scientific literature on this subject are rare. The purpose of this study was to evaluate a number of different test procedures for assessing chewability, starting from standard breaking force and strength testing and progressing to develop new procedures that simulate the actual chewing action on tablets. A further goal was to apply these test procedures to characterize the chewability of the novel phosphate binder PA21 in comparison with a commercially available phosphate binder chewable tablet product based on lanthanum (Fosrenol®) and a chewable tablet product containing calcium (Calcimagon®) - the latter being used as a standard for its very good chewability. For this purpose, a number of development formulations (different batches of PA21) were tested. The radial or diametrical tablet breaking force offers a poor means of assessing chewability while the axial breaking force was concluded to better reflect the effect of chewing on the tablet. Measurement of tablet behavior upon repeated loading afforded the best simulation of the actual chewing action and was found to have a good discriminating power with respect to chewability of the tested tablets, especially when the tablet was moistened with artificial saliva. The developed tests are shown to be more suitable for evaluating chewing properties of tablets than currently used Pharmacopeial tests. Following ICHQ6, which calls for specification of hardness for chewable tablets, these test procedures enabled the optimal chewability features of PA21 tablets in development to be confirmed whilst still maintaining capabilities for robust production and transportation processes.

Measuring Temporal Resolution (Release of Masking) with a Hughson-Westlake Up-Down Instead of a Békèsy-Tracking Procedure.

PubMed

Rhebergen, Koenraad S; van Esch, Thamar E M; Dreschler, Wouter A

2015-06-01

A temporal resolution test in addition to the pure-tone audiogram may be of great clinical interest because of its relevance in speech perception and expected relevance in hearing aid fitting. Larsby and Arlinger developed an appropriate clinical test, but this test uses a Békèsy-tracking procedure for estimating masked thresholds in stationary and interrupted noise to assess release of masking (RoM) for temporal resolution. Generally the Hughson-Westlake up-down procedure is used in the clinic to measure the pure-tone thresholds in quiet. A uniform approach will facilitate clinical application and might be appropriate for RoM measurements as well. Because there is no golden standard for measuring the RoM in the clinic, we examine in the present study the Hughson-Westlake up-down procedure to measure the RoM and compare the results with the Békèsy-tracking procedure. The purpose of the current study was to examine the differences between a Békèsy-tracking procedure and the Hughson-Westlake up-down procedure for estimating masked thresholds in stationary and interrupted noise to assess RoM. RoM is assessed in eight normal-hearing (NH) and ten hearing-impaired (HI) listeners through both methods. Results from both methods are compared with each other and with predicted thresholds from a model. Wilcoxon signed-rank tests, paired t tests. Some differences between the two methods were found. We used a model to quantify the results of the two measurement procedures. The results of the Hughson-Westlake procedure were clearly better in agreement with the model than the results of the Békèsy-tracking procedure. Furthermore, the Békèsy-tracking procedure showed more spread in the results of the NH listeners than the Hughson-Westlake procedure. The Hughson-Westlake procedure seems to be an applicable alternative for measuring RoM for temporal resolution in the clinical audiological practice. American Academy of Audiology.

Analysis of simulated angiographic procedures. Part 2: extracting efficiency data from audio and video recordings.

PubMed

Duncan, James R; Kline, Benjamin; Glaiberman, Craig B

2007-04-01

To create and test methods of extracting efficiency data from recordings of simulated renal stent procedures. Task analysis was performed and used to design a standardized testing protocol. Five experienced angiographers then performed 16 renal stent simulations using the Simbionix AngioMentor angiographic simulator. Audio and video recordings of these simulations were captured from multiple vantage points. The recordings were synchronized and compiled. A series of efficiency metrics (procedure time, contrast volume, and tool use) were then extracted from the recordings. The intraobserver and interobserver variability of these individual metrics was also assessed. The metrics were converted to costs and aggregated to determine the fixed and variable costs of a procedure segment or the entire procedure. Task analysis and pilot testing led to a standardized testing protocol suitable for performance assessment. Task analysis also identified seven checkpoints that divided the renal stent simulations into six segments. Efficiency metrics for these different segments were extracted from the recordings and showed excellent intra- and interobserver correlations. Analysis of the individual and aggregated efficiency metrics demonstrated large differences between segments as well as between different angiographers. These differences persisted when efficiency was expressed as either total or variable costs. Task analysis facilitated both protocol development and data analysis. Efficiency metrics were readily extracted from recordings of simulated procedures. Aggregating the metrics and dividing the procedure into segments revealed potential insights that could be easily overlooked because the simulator currently does not attempt to aggregate the metrics and only provides data derived from the entire procedure. The data indicate that analysis of simulated angiographic procedures will be a powerful method of assessing performance in interventional radiology.

Development and Initial Evaluation of an Acceptance Testing Procedure for Air Supply and Distribution Systems in New Army Facilities

DTIC Science & Technology

1988-09-01

Unfortunately, although current construction practices can produce functional HVAC systems that provide adequate heating and cooling , they do not guarantee...developed by interviewing heating, ventilating, and air-conditioning ( HVAC ) profes- sionals, reviewing technical literature, and consolidating these...for recording this information. A glossary of possibly unfamiliar HVAC terms is included. An informal evaluation of the procedure showed that

NDE detectability of fatigue-type cracks in high-strength alloys: NDI reliability assessments

NASA Technical Reports Server (NTRS)

Christner, Brent K.; Long, Donald L.; Rummel, Ward D.

1988-01-01

This program was conducted to generate quantitative flaw detection capability data for the nondestructive evaluation (NDE) techniques typically practiced by aerospace contractors. Inconel 718 and Haynes 188 alloy test specimens containing fatigue flaws with a wide distribution of sizes were used to assess the flaw detection capabilities at a number of contractor and government facilities. During this program 85 inspection sequences were completed presenting a total of 20,994 fatigue cracks to 53 different inspectors. The inspection sequences completed included 78 liquid penetrant, 4 eddy current, and 3 ultrasonic evaluations. The results of the assessment inspections are presented and discussed. In generating the flaw detection capability data base, procedures for data collection, data analysis, and specimen care and maintenance were developed, demonstrated, and validated. The data collection procedures and methods that evolved during this program for the measurement of flaw detection capabilities and the effects of inspection variables on performance are discussed. The Inconel 718 and Haynes 188 test specimens that were used in conducting this program and the NDE assessment procedures that were demonstrated, provide NASA with the capability to accurately assess the flaw detection capabilities of specific inspection procedures being applied or proposed for use on current and future fracture control hardware program.

A Method of Separation Assurance for Instrument Flight Procedures at Non-Radar Airports

NASA Technical Reports Server (NTRS)

Conway, Sheila R.; Consiglio, Maria

2002-01-01

A method to provide automated air traffic separation assurance services during approach to or departure from a non-radar, non-towered airport environment is described. The method is constrained by provision of these services without radical changes or ambitious investments in current ground-based technologies. The proposed procedures are designed to grant access to a large number of airfields that currently have no or very limited access under Instrument Flight Rules (IFR), thus increasing mobility with minimal infrastructure investment. This paper primarily addresses a low-cost option for airport and instrument approach infrastructure, but is designed to be an architecture from which a more efficient, albeit more complex, system may be developed. A functional description of the capabilities in the current NAS infrastructure is provided. Automated terminal operations and procedures are introduced. Rules of engagement and the operations are defined. Results of preliminary simulation testing are presented. Finally, application of the method to more terminal-like operations, and major research areas, including necessary piloted studies, are discussed.

NASA GRC and MSFC Space-Plasma Arc Testing Procedures

NASA Technical Reports Server (NTRS)

Ferguson, Dale C.; Vayner, Boris V.; Galofaro, Joel T,; Hillard, G. Barry; Vaughn, Jason; Schneider, Todd

2005-01-01

Tests of arcing and current collection in simulated space plasma conditions have been performed at the NASA Glenn Research Center (GRC) in Cleveland, Ohio, for over 30 years and at the Marshall Space Flight Center (MSFC) in Huntsville, Alabama, for almost as long. During this period, proper test conditions for accurate and meaningful space simulation have been worked out, comparisons with actual space performance in spaceflight tests and with real operational satellites have been made, and NASA has achieved our own internal standards for test protocols. It is the purpose of this paper to communicate the test conditions, test procedures, and types of analysis used at NASA GRC and MSFC to the space environmental testing community at large, to help with international space-plasma arcing-testing standardization. To be discussed are: 1.Neutral pressures, neutral gases, and vacuum chamber sizes. 2. Electron and ion densities, plasma uniformity, sample sizes, and Debuy lengths. 3. Biasing samples versus self-generated voltages. Floating samples versus grounded. 4. Power supplies and current limits. Isolation of samples from power supplies during arcs. 5. Arc circuits. Capacitance during biased arc-threshold tests. Capacitance during sustained arcing and damage tests. Arc detection. Prevention sustained discharges during testing. 6. Real array or structure samples versus idealized samples. 7. Validity of LEO tests for GEO samples. 8. Extracting arc threshold information from arc rate versus voltage tests. 9. Snapover and current collection at positive sample bias. Glows at positive bias. Kapon (R) pyrolisis. 10. Trigger arc thresholds. Sustained arc thresholds. Paschen discharge during sustained arcing. 11. Testing for Paschen discharge threshold. Testing for dielectric breakdown thresholds. Testing for tether arcing. 12. Testing in very dense plasmas (ie thruster plumes). 13. Arc mitigation strategies. Charging mitigation strategies. Models. 14. Analysis of test results. Finally, the necessity of testing will be emphasized, not to the exclusion of modeling, but as part of a complete strategy for determining when and if arcs will occur, and preventing them from occurring in space.

NASA GRC and MSFC Space-Plasma Arc Testing Procedures

NASA Technical Reports Server (NTRS)

Ferguson, Dale C.a; Vayner, Boris V.; Galofaro, Joel T.; Hillard, G. Barry; Vaughn, Jason; Schneider, Todd

2005-01-01

Tests of arcing and current collection in simulated space plasma conditions have been performed at the NASA Glenn Research Center (GRC) in Cleveland, Ohio, for over 30 years and at the Marshall Space flight Center (MSFC) for almost as long. During this period, proper test conditions for accurate and meaningful space simulation have been worked out, comparisons with actual space performance in spaceflight tests and with real operational satellites have been made, and NASA has achieved our own internal standards for test protocols. It is the purpose of this paper to communicate the test conditions, test procedures, and types of analysis used at NASA GRC and MSFC to the space environmental testing community at large, to help with international space-plasma arcing testing standardization. To be discussed are: 1. Neutral pressures, neutral gases, and vacuum chamber sizes. 2. Electron and ion densities, plasma uniformity, sample sizes, and Debye lengths. 3. Biasing samples versus self-generated voltages. Floating samples versus grounded. 4. Power supplies and current limits. Isolation of samples from power supplies during arcs. Arc circuits. Capacitance during biased arc-threshold tests. Capacitance during sustained arcing and damage tests. Arc detection. Preventing sustained discharges during testing. 5. Real array or structure samples versus idealized samples. 6. Validity of LEO tests for GEO samples. 7. Extracting arc threshold information from arc rate versus voltage tests. 8 . Snapover and current collection at positive sample bias. Glows at positive bias. Kapton pyrolization. 9. Trigger arc thresholds. Sustained arc thresholds. Paschen discharge during sustained arcing. 10. Testing for Paschen discharge thresholds. Testing for dielectric breakdown thresholds. Testing for tether arcing. 11. Testing in very dense plasmas (ie thruster plumes). 12. Arc mitigation strategies. Charging mitigation strategies. Models. 13. Analysis of test results. Finally, the necessity of testing will be emphasized, not to the exclusion of modeling, but as part of a complete strategy for determining when and if arcs will occur, and preventing them from occurring in space.

Environmental and toxicological planning in polymer production and disposal.

PubMed Central

Levinskas, G J

1975-01-01

There is neither a prescribed format nor a rigid sequence of testing to follow for the assessment of health and environmental effects of chemicals. Conventional animal toxicity tests plus medical surveillance and monitoring of exposed human populations will provide knowledge of the biological effects of chemicals and assurance that they can be handled safely. Useful information also can be derived from other test procedures. These include extraction studies to measure the amounts of additives which can leach from polymers, toxicity tests using aquatic organisms and birds, and determination of the biodegradability of materials and their potential for accumulation and magnification in biological systems. Current concern over pyrolysis products of polymers points up the need for defining the variables involved and development of test procedures by which meaningful evaluations of potential health hazards can be made. PMID:1175554

Promoting clinical and laboratory interaction by harmonization.

PubMed

Plebani, Mario; Panteghini, Mauro

2014-05-15

The lack of interchangeable results in current practice among clinical laboratories has underpinned greater attention to standardization and harmonization projects. Although the focus was mainly on the standardization and harmonization of measurement procedures and their results, the scope of harmonization goes beyond method and analytical results: it includes all other aspects of laboratory testing, including terminology and units, report formats, reference limits and decision thresholds, as well as test profiles and criteria for the interpretation of results. In particular, as evidence collected in last decades demonstrates that pre-pre- and post-post-analytical steps are more vulnerable to errors, harmonization initiatives should be performed to improve procedures and processes at the laboratory-clinical interface. Managing upstream demand, down-stream interpretation of laboratory results, and subsequent appropriate action through close relationships between laboratorians and clinicians remains a crucial issue of the laboratory testing process. Therefore, initiatives to improve test demand management from one hand and to harmonize procedures to improve physicians' acknowledgment of laboratory data and their interpretation from the other hand are needed in order to assure quality and safety in the total testing process. © 2013.

The compartment bag test (CBT) for enumerating fecal indicator bacteria: Basis for design and interpretation of results.

PubMed

Gronewold, Andrew D; Sobsey, Mark D; McMahan, Lanakila

2017-06-01

For the past several years, the compartment bag test (CBT) has been employed in water quality monitoring and public health protection around the world. To date, however, the statistical basis for the design and recommended procedures for enumerating fecal indicator bacteria (FIB) concentrations from CBT results have not been formally documented. Here, we provide that documentation following protocols for communicating the evolution of similar water quality testing procedures. We begin with an overview of the statistical theory behind the CBT, followed by a description of how that theory was applied to determine an optimal CBT design. We then provide recommendations for interpreting CBT results, including procedures for estimating quantiles of the FIB concentration probability distribution, and the confidence of compliance with recognized water quality guidelines. We synthesize these values in custom user-oriented 'look-up' tables similar to those developed for other FIB water quality testing methods. Modified versions of our tables are currently distributed commercially as part of the CBT testing kit. Published by Elsevier B.V.

Ultraviolet Spectrometer and Polarimeter (UVSP) software development and hardware tests for the solar maximum mission

NASA Technical Reports Server (NTRS)

1984-01-01

An analysis of UVSP wavelength drive hardware, problems, and recovery procedures; radiative power loss from solar plasmas; and correlations between observed UV brightness and inferred photospheric currents are given.

Electrical resistivity measurement of mechanically stabilized Earth wall backfill : final report.

DOT National Transportation Integrated Search

2016-06-01

In Kansas, mechanically stabilized earth (MSE) retaining walls are typically backfilled with coarse aggregate. : Current backfill material testing procedures used by the Kansas Department of Transportation (KDOT) utilize on-site : observations for co...

Occupational exposures to human immunodeficiency virus, hepatitis B virus, and hepatitis C virus: risk, prevention, and management.

PubMed

Cleveland, Jennifer L; Cardo, Denise M

2003-10-01

Current data indicate that the risk for transmitting bloodborne pathogens in dental health care settings is low. Pre-exposure hepatitis B vaccination and the use of standard precautions to prevent exposure to blood are the most effective strategies for preventing DHCP from occupational infection with HIV, HBV or HCV. Each dental health care facility should develop a comprehensive written program for preventing and managing occupational exposures to blood that: (1) describes the types of blood exposures that may place DHCP at risk for infection; (2) outlines procedures for promptly reporting and evaluating such exposures; and (3) identifies a health care professional who is qualified to provide counseling and perform all medical evaluations and procedures in accordance with the most current USPHS recommendations. Finally, resources should be available that permit rapid access to clinical care, testing, counseling, and PEP for exposed DHCP and the testing and counseling of source patients.

Automation of Command and Data Entry in a Glovebox Work Volume: An Evaluation of Data Entry Devices

NASA Technical Reports Server (NTRS)

Steele, Marianne K.; Nakamura, Gail; Havens, Cindy; LeMay, Moira

1996-01-01

The present study was designed to examine the human-computer interface for data entry while performing experimental procedures within a glovebox work volume in order to make a recommendation to the Space Station Biological Research Project for a data entry system to be used within the Life Sciences Glovebox. Test subjects entered data using either a manual keypad, similar to a standard computer numerical keypad located within the glovebox work volume, or a voice input system using a speech recognition program with a microphone headset. Numerical input and commands were programmed in an identical manner between the two systems. With both electronic systems, a small trackball was available within the work volume for cursor control. Data, such as sample vial identification numbers, sample tissue weights, and health check parameters of the specimen, were entered directly into procedures that were electronically displayed on a video monitor within the glovebox. A pen and paper system with a 'flip-chart' format for procedure display, similar to that currently in use on the Space Shuttle, was used as a baseline data entry condition. Procedures were performed by a single operator; eight test subjects were used in the study. The electronic systems were tested under both a 'nominal' or 'anomalous' condition. The anomalous condition was introduced into the experimental procedure to increase the probability of finding limitations or problems with human interactions with the electronic systems. Each subject performed five test runs during a test day: two procedures each with voice and keypad, one with and one without anomalies, and one pen and paper procedure. The data collected were both quantitative (times, errors) and qualitative (subjective ratings of the subjects).

Spaceport Command and Control System Software Development

NASA Technical Reports Server (NTRS)

Glasser, Abraham

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administration's (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This large system requires a large amount of intensive testing that will properly measure the capabilities of the system. Automating the test procedures would save the project money from human labor costs, as well as making the testing process more efficient. Therefore, the Exploration Systems Division (formerly the Electrical Engineering Division) at Kennedy Space Center (KSC) has recruited interns for the past two years to work alongside full-time engineers to develop these automated tests, as well as innovate upon the current automation process.

Development and Application of Intelligence Tests for the Blind: A Research Utilization Conference. Final Report.

ERIC Educational Resources Information Center

Curtis, W. Scott

The purpose of this project was to inquire into the current status of development, past use, availability, and future planning of intelligence tests for the visually handicapped in relation to the fields of psychological, educational, and vocational counseling. The project procedure was that of a research utilization conference involving the…

Cultural-Linguistic Test Adaptations: Guidelines for Selection, Alteration, Use, and Review

ERIC Educational Resources Information Center

Krach, S. Kathleen; McCreery, Michael P.; Guerard, Jessika

2017-01-01

In 1991, Bracken and Barona wrote an article for "School Psychology International" focusing on state of the art procedures for translating and using tests across multiple languages. Considerable progress has been achieved in this area over the 25 years between that publication and today. This article seeks to provide a more current set…

A competency based selection procedure for Dutch postgraduate GP training: a pilot study on validity and reliability.

PubMed

Vermeulen, Margit I; Tromp, Fred; Zuithoff, Nicolaas P A; Pieters, Ron H M; Damoiseaux, Roger A M J; Kuyvenhoven, Marijke M

2014-12-01

Abstract Background: Historically, semi-structured interviews (SSI) have been the core of the Dutch selection for postgraduate general practice (GP) training. This paper describes a pilot study on a newly designed competency-based selection procedure that assesses whether candidates have the competencies that are required to complete GP training. The objective was to explore reliability and validity aspects of the instruments developed. The new selection procedure comprising the National GP Knowledge Test (LHK), a situational judgement tests (SJT), a patterned behaviour descriptive interview (PBDI) and a simulated encounter (SIM) was piloted alongside the current procedure. Forty-seven candidates volunteered in both procedures. Admission decision was based on the results of the current procedure. Study participants did hardly differ from the other candidates. The mean scores of the candidates on the LHK and SJT were 21.9 % (SD 8.7) and 83.8% (SD 3.1), respectively. The mean self-reported competency scores (PBDI) were higher than the observed competencies (SIM): 3.7(SD 0.5) and 2.9(SD 0.6), respectively. Content-related competencies showed low correlations with one another when measured with different instruments, whereas more diverse competencies measured by a single instrument showed strong to moderate correlations. Moreover, a moderate correlation between LHK and SJT was found. The internal consistencies (intraclass correlation, ICC) of LHK and SJT were poor while the ICC of PBDI and SIM showed acceptable levels of reliability. Findings on content validity and reliability of these new instruments are promising to realize a competency based procedure. Further development of the instruments and research on predictive validity should be pursued.

Non-animal Replacements for Acute Toxicity Testing.

PubMed

Barker-Treasure, Carol; Coll, Kevin; Belot, Nathalie; Longmore, Chris; Bygrave, Karl; Avey, Suzanne; Clothier, Richard

2015-07-01

Current approaches to predicting adverse effects in humans from acute toxic exposure to cosmetic ingredients still heavily necessitate the use of animals under EU legislation, particularly in the context of the REACH system, when cosmetic ingredients are also destined for use in other industries. These include the LD50 test, the Up-and-Down Procedure and the Fixed Dose Procedure, which are regarded as having notable scientific deficiencies and low transferability to humans. By expanding on previous in vitro tests, such as the animal cell-based 3T3 Neutral Red Uptake (NRU) assay, this project aims to develop a truly animal-free predictive test for the acute toxicity of cosmetic ingredients in humans, by using human-derived cells and a prediction model that does not rely on animal data. The project, funded by Innovate UK, will incorporate the NRU assay with human dermal fibroblasts in animal product-free culture, to generate an in vitro protocol that can be validated as an accepted replacement for the currently available in vivo tests. To date, the project has successfully completed an assessment of the robustness and reproducibility of the method, by using sodium lauryl sulphate (SLS) as a positive control, and displaying analogous results to those of the original studies with mouse 3T3 cells. Currently, the testing of five known ingredients from key groups (a surfactant, a preservative, a fragrance, a colour and an emulsifier) is under way. The testing consists of initial range-finding runs followed by three valid runs of a main experiment with the appropriate concentration ranges, to generate IC50 values. Expanded blind trials of 20 ingredients will follow. Early results indicate that this human cell-based test holds the potential to replace aspects of in vivo animal acute toxicity testing, particularly with reference to cosmetic ingredients. 2015 FRAME.

Container Approval for the Disposal of Radioactive Waste with Negligible Heat Generation in the German Konrad Repository - 12148

DOE Office of Scientific and Technical Information (OSTI.GOV)

Voelzke, Holger; Nieslony, Gregor; Ellouz, Manel

Since the license for the Konrad repository was finally confirmed by legal decision in 2007, the Federal Institute for Radiation Protection (BfS) has been performing further planning and preparation work to prepare the repository for operation. Waste conditioning and packaging has been continued by different waste producers as the nuclear industry and federal research institutes on the basis of the official disposal requirements. The necessary prerequisites for this are approved containers as well as certified waste conditioning and packaging procedures. The Federal Institute for Materials Research and Testing (BAM) is responsible for container design testing and evaluation of quality assurancemore » measures on behalf of BfS under consideration of the Konrad disposal requirements. Besides assessing the container handling stability (stacking tests, handling loads), design testing procedures are performed that include fire tests (800 deg. C, 1 hour) and drop tests from different heights and drop orientations. This paper presents the current state of BAM design testing experiences about relevant container types (box shaped, cylindrical) made of steel sheets, ductile cast iron or concrete. It explains usual testing and evaluation methods which range from experimental testing to analytical and numerical calculations. Another focus has been laid on already existing containers and packages. The question arises as to how they can be evaluated properly especially with respect to lack of completeness of safety assessment and fabrication documentation. At present BAM works on numerous applications for container design testing for the Konrad repository. Some licensing procedures were successfully finished in the past and BfS certified several container types like steel sheet, concrete until cast iron containers which are now available for waste packaging for final disposal. However, large quantities of radioactive wastes had been placed into interim storage using containers which are not already licensed for the Konrad repository. Safety assessment of these so-called 'old' containers is a big challenge for all parties because documentation sheets about container design testing and fabrication often contain gaps or have not yet been completed. Appropriate solution strategies are currently under development and discussion. Furthermore, BAM has successfully initiated and established an information forum, called 'ERFA QM Konrad Containers', which facilitates discussions on various issues of common interest with respect to Konrad container licensing procedures as well as the interpretation of disposal requirements under consideration of operational needs. Thus, it provides additional, valuable supports for container licensing procedures. (authors)« less

Current status of endoluminal grafting for exclusion of abdominal aortic aneurysms. The beauty and the beast.

PubMed Central

Diethrich, E B

1998-01-01

The exclusion of abdominal aortic aneurysms with endoluminal grafts has generated a great deal of interest since the early 1990s, and many centers are currently evaluating the procedure and comparing it to classic surgical exclusion. Although endoluminal grafting procedures show promise, development and clinical testing of devices is a time-consuming process that is influenced greatly by the regulatory climate in the country where the clinical trials take place. Nevertheless, a number of devices are currently under study, and the advantages of 2nd- and 3rd-generation technology are reflected in reduced rates of complications such as endoleaks and thrombosis. Further study will be required to perfect these devices and observe their long-term success in the exclusion of abdominal aortic aneurysms. Images PMID:9566057

Current status of endoluminal grafting for exclusion of abdominal aortic aneurysms. The beauty and the beast.

PubMed

Diethrich, E B

1998-01-01

The exclusion of abdominal aortic aneurysms with endoluminal grafts has generated a great deal of interest since the early 1990s, and many centers are currently evaluating the procedure and comparing it to classic surgical exclusion. Although endoluminal grafting procedures show promise, development and clinical testing of devices is a time-consuming process that is influenced greatly by the regulatory climate in the country where the clinical trials take place. Nevertheless, a number of devices are currently under study, and the advantages of 2nd- and 3rd-generation technology are reflected in reduced rates of complications such as endoleaks and thrombosis. Further study will be required to perfect these devices and observe their long-term success in the exclusion of abdominal aortic aneurysms.

Modelling high frequency phenomena in the rotor of induction motors under no-load test conditions

NASA Astrophysics Data System (ADS)

Boglietti, Aldo; Bottauscio, Oriano; Chiampi, Mario; Lazzari, Mario

2003-01-01

The paper aims to deep the electromagnetic phenomena in the rotor of induction motors produced during the no-load test by the high-order harmonics of the spatial distribution of magnetic flux. The analysis is carried out by a flux driven finite element procedure, which can take into account the hysteresis of magnetic material, the induced currents in rotor cage and the eddy currents in the laminations. The computed results, including losses and local waveforms of electrical and magnetic quantities, are finally discussed.

Crash Certification by Analysis - Are We There Yet?

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Fasanella, Edwin L.; Lyle, Karen H.

2006-01-01

This paper addresses the issue of crash certification by analysis. This broad topic encompasses many ancillary issues including model validation procedures, uncertainty in test data and analysis models, probabilistic techniques for test-analysis correlation, verification of the mathematical formulation, and establishment of appropriate qualification requirements. This paper will focus on certification requirements for crashworthiness of military helicopters; capabilities of the current analysis codes used for crash modeling and simulation, including some examples of simulations from the literature to illustrate the current approach to model validation; and future directions needed to achieve "crash certification by analysis."

Investigation of the effects of external current systems on the MAGSAT data utilizing grid cell modeling techniques

NASA Technical Reports Server (NTRS)

Klumpar, D. M. (Principal Investigator)

1982-01-01

Progress made in reducing MAGSAT data and displaying magnetic field perturbations caused primarily by external currents is reported. A periodic and repeatable perturbation pattern is described that arises from external current effects but appears as unique signatures associated with upper middle latitudes on the Earth's surface. Initial testing of the modeling procedure that was developed to compute the magnetic fields at satellite orbit due to current distributions in the ionosphere and magnetosphere is also discussed. The modeling technique utilizes a linear current element representation of the large scale space current system.

Accelerated testing technique for evaluating performance of chemical air filters for DUV photolithographic equipment

NASA Astrophysics Data System (ADS)

Kishkovich, Oleg P.; Bolgov, Dennis; Goodwin, William

1999-06-01

In this paper, the authors discuss the requirements for chemical air filtration system used in conjunction with modern DUV photolithography equipment. Among the topics addressed are the scope of pollutants, their respective internal and external sources, and an overview of different types of filtration technologies currently in use. Key filtration parameters, including removal efficiency, service life, and spill protection capacity, are discussed and supported by actual data, reflection the total molecular base concentration in operational IC manufacturing facilities. The authors also describe a time-accelerated testing procedure for comparing and evaluating different filtration technologies and designs, and demonstrate how this three-day test procedure can reliably predict an effective filter service life up to ten years.

Uncertainties in Estimates of Fleet Average Fuel Economy : A Statistical Evaluation

DOT National Transportation Integrated Search

1977-01-01

Research was performed to assess the current Federal procedure for estimating the average fuel economy of each automobile manufacturer's new car fleet. Test vehicle selection and fuel economy estimation methods were characterized statistically and so...

Curling and warping of concrete pavement: an investigation and proof of concept study : technical summary.

DOT National Transportation Integrated Search

2016-06-01

In Kansas, mechanically stabilized earth (MSE) retaining walls are typically : backfilled with coarse aggregate. Current backfill material testing procedures used : by the Kansas Department of Transportation (KDOT) utilize on-site observations for : ...

Tested Demonstrations.

ERIC Educational Resources Information Center

Gilbert, George L., Ed.

1985-01-01

List of materials needed, procedures used, and results obtained are provided for two demonstrations. The first is an inexpensive and quick method for demonstrating column chromatography of plant pigments of spinach extract. The second is a demonstration of cathodic protection by impressed current. (JN)

A rapid method for soil cement design : Louisiana slope value method.

DOT National Transportation Integrated Search

1964-03-01

The current procedure used by the Louisiana Department of Highways for laboratory design of cement stabilized soil base and subbase courses is taken from standard AASHO test methods, patterned after Portland Cement Association criteria. These methods...

Mast cells and basophils are essential for allergies: mechanisms of allergic inflammation and a proposed procedure for diagnosis

PubMed Central

He, Shao-heng; Zhang, Hui-yun; Zeng, Xiao-ning; Chen, Dong; Yang, Ping-chang

2013-01-01

The current definition of allergy is a group of IgE-mediated diseases. However, a large portion of patients with clinical manifestations of allergies do not exhibit elevated serum levels of IgE (sIgEs). In this article, three key factors, ie soluble allergens, sIgEs and mast cells or basophils, representing the causative factors, messengers and primary effector cells in allergic inflammation, respectively, were discussed. Based on current knowledge on allergic diseases, we propose that allergic diseases are a group of diseases mediated through activated mast cells and/or basophils in sensitive individuals, and allergic diseases include four subgroups: (1) IgE dependent; (2) other immunoglobulin dependent; (3) non-immunoglobulin mediated; (4) mixture of the first three subgroups. According to our proposed definition, pseudo-allergic-reactions, in which mast cell or basophil activation is not mediated via IgE, or to a lesser extent via IgG or IgM, should be non-IgE-mediated allergic diseases. Specific allergen challenge tests (SACTs) are gold standard tests for diagnosing allergies in vivo, but risky. The identification of surface membrane activation markers of mast cells and basophils (CD203c, CCR3, CD63, etc) has led to development of the basophil activation test (BAT), an in vitro specific allergen challenge test (SACT). Based on currently available laboratory allergy tests, we here propose a laboratory examination procedure for allergy. PMID:23974516

European type-approval test procedure for evaporative emissions from passenger cars against real-world mobility data from two Italian provinces.

PubMed

Martini, Giorgio; Paffumi, Elena; De Gennaro, Michele; Mellios, Giorgos

2014-07-15

This paper presents an evaluation of the European type-approval test procedure for evaporative emissions from passenger cars based on real-world mobility data. The study relies on two large databases of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems in the Italian provinces of Modena and Firenze. Approximately 28,000 vehicles were monitored, corresponding to approximately 36 million kilometres over a period of one month. The driving pattern of each vehicle was processed to derive the relation between trip length and parking duration, and the rate of occurrence of parking events against multiple evaporative cycles, defined on the basis of the type-approval test procedure as 12-hour diurnal time windows. These results are used as input for an emission simulation model, which calculates the total evaporative emissions given the characteristics of the evaporative emission control system of the vehicle and the ambient temperature conditions. The results suggest that the evaporative emission control system, fitted to the vehicles from Euro 3 step and optimised for the current type-approval test procedure, could not efficiently work under real-world conditions, resulting in evaporative emissions well above the type-approval limit, especially for small size vehicles and warm climate conditions. This calls for a revision of the type-approval test procedure in order to address real-world evaporative emissions. Copyright © 2014. Published by Elsevier B.V.

Framework conditions and requirements to ensure the technical functional safety of reprocessed medical devices.

PubMed

Kraft, Marc

2008-09-03

Testing and restoring technical-functional safety is an essential part of medical device reprocessing. Technical functional tests have to be carried out on the medical device in the course of the validation of reprocessing procedures. These ensure (in addition to the hygiene tests) that the reprocessing procedure is suitable for the medical device. Functional tests are, however, also a part of reprocessing procedures. As a stage in the reprocessing, they ensure for the individual medical device that no damage or other changes limit the performance. When determining which technical-functional tests are to be carried out, the current technological standard has to be taken into account in the form of product-specific and process-oriented norms. Product-specific norms primarily define safety-relevant requirements. The risk management method described in DIN EN ISO 14971 is the basis for recognising hazards; the likelihood of such hazards arising can be minimised through additional technical-functional tests, which may not yet have been standardised. Risk management is part of a quality management system, which must be bindingly certified for manufacturers and processors of critical medical devices with particularly high processing demands by a body accredited by the competent authority.

Framework conditions and requirements to ensure the technical functional safety of reprocessed medical devices

PubMed Central

Kraft, Marc

2008-01-01

Testing and restoring technical-functional safety is an essential part of medical device reprocessing. Technical functional tests have to be carried out on the medical device in the course of the validation of reprocessing procedures. These ensure (in addition to the hygiene tests) that the reprocessing procedure is suitable for the medical device. Functional tests are, however, also a part of reprocessing procedures. As a stage in the reprocessing, they ensure for the individual medical device that no damage or other changes limit the performance. When determining which technical-functional tests are to be carried out, the current technological standard has to be taken into account in the form of product-specific and process-oriented norms. Product-specific norms primarily define safety-relevant requirements. The risk management method described in DIN EN ISO 14971 is the basis for recognising hazards; the likelihood of such hazards arising can be minimised through additional technical-functional tests, which may not yet have been standardised. Risk management is part of a quality management system, which must be bindingly certified for manufacturers and processors of critical medical devices with particularly high processing demands by a body accredited by the competent authority. PMID:20204095

Synthesis study of nondestructive testing devices for use in overlay thickness design of flexible pavements

NASA Astrophysics Data System (ADS)

Smith, R. E.; Lytton, R. L.

1984-04-01

A ready reference for highway engineers who are interested in purchasing nondestructive testing (NDT) equipment for use in designing overlays for flexible pavements was prepared. All commercially available equipment is described. Information includes basic descriptions plus current prices quoted by the manufacturers/distributors. To determine user comments, a questionnaire was sent to nine State agencies, and one Federal agency. The responses to these questionnaires are summarized. Overlay thickness design procedures for flexible pavements are reviewed. Important components related to the use of NDT deflection measuremnts in overlay design are identified and addressed. Summary tables of equipment characteristics and overlay design procedures are presented.

Iterative procedures for space shuttle main engine performance models

NASA Technical Reports Server (NTRS)

Santi, L. Michael

1989-01-01

Performance models of the Space Shuttle Main Engine (SSME) contain iterative strategies for determining approximate solutions to nonlinear equations reflecting fundamental mass, energy, and pressure balances within engine flow systems. Both univariate and multivariate Newton-Raphson algorithms are employed in the current version of the engine Test Information Program (TIP). Computational efficiency and reliability of these procedures is examined. A modified trust region form of the multivariate Newton-Raphson method is implemented and shown to be superior for off nominal engine performance predictions. A heuristic form of Broyden's Rank One method is also tested and favorable results based on this algorithm are presented.

Cost-Minimization Analysis of Open and Endoscopic Carpal Tunnel Release.

PubMed

Zhang, Steven; Vora, Molly; Harris, Alex H S; Baker, Laurence; Curtin, Catherine; Kamal, Robin N

2016-12-07

Carpal tunnel release is the most common upper-limb surgical procedure performed annually in the U.S. There are 2 surgical methods of carpal tunnel release: open or endoscopic. Currently, there is no clear clinical or economic evidence supporting the use of one procedure over the other. We completed a cost-minimization analysis of open and endoscopic carpal tunnel release, testing the null hypothesis that there is no difference between the procedures in terms of cost. We conducted a retrospective review using a private-payer and Medicare Advantage database composed of 16 million patient records from 2007 to 2014. The cohort consisted of records with an ICD-9 (International Classification of Diseases, Ninth Revision) diagnosis of carpal tunnel syndrome and a CPT (Current Procedural Terminology) code for carpal tunnel release. Payer fees were used to define cost. We also assessed other associated costs of care, including those of electrodiagnostic studies and occupational therapy. Bivariate comparisons were performed using the chi-square test and the Student t test. Data showed that 86% of the patients underwent open carpal tunnel release. Reimbursement fees for endoscopic release were significantly higher than for open release. Facility fees were responsible for most of the difference between the procedures in reimbursement: facility fees averaged $1,884 for endoscopic release compared with $1,080 for open release (p < 0.0001). Endoscopic release also demonstrated significantly higher physician fees than open release (an average of $555 compared with $428; p < 0.0001). Occupational therapy fees associated with endoscopic release were less than those associated with open release (an average of $237 per session compared with $272; p = 0.07). The total average annual reimbursement per patient for endoscopic release (facility, surgeon, and occupational therapy fees) was significantly higher than for open release ($2,602 compared with $1,751; p < 0.0001). Our data showed that the total average fees per patient for endoscopic release were significantly higher than those for open release, although there currently is no strong evidence supporting better clinical outcomes of either technique. Value-based health-care models that favor delivering high-quality care and improving patient health, while also minimizing costs, may favor open carpal tunnel release.

NASA GRC and MSFC Space-Plasma Arc Testing Procedures

NASA Technical Reports Server (NTRS)

Ferguson, Dale C.; Vayner, Boris V.; Galofaro, Joel T.; Hillard, G. Barry; Vaughn, Jason; Schneider, Todd

2007-01-01

Tests of arcing and current collection in simulated space plasma conditions have been performed at the NASA Glenn Research Center (GRC) in Cleveland, Ohio, for over 30 years and at the Marshall Space Flight Center (MSFC) in Huntsville, Alabama, for almost as long. During this period, proper test conditions for accurate and meaningful space simulation have been worked out, comparisons with actual space performance in spaceflight tests and with real operational satellites have been made, and NASA has achieved our own internal standards for test protocols. It is the purpose of this paper to communicate the test conditions, test procedures, and types of analysis used at NASA GRC and MSFC to the space environmental testing community at large, to help with international space-plasma arcing-testing standardization. Discussed herein are neutral gas conditions, plasma densities and uniformity, vacuum chamber sizes, sample sizes and Debye lengths, biasing samples versus self-generated voltages, floating samples versus grounded samples, test electrical conditions, arc detection, preventing sustained discharges during testing, real samples versus idealized samples, validity of LEO tests for GEO samples, extracting arc threshold information from arc rate versus voltage tests, snapover, current collection, and glows at positive sample bias, Kapton pyrolysis, thresholds for trigger arcs, sustained arcs, dielectric breakdown and Paschen discharge, tether arcing and testing in very dense plasmas (i.e. thruster plumes), arc mitigation strategies, charging mitigation strategies, models, and analysis of test results. Finally, the necessity of testing will be emphasized, not to the exclusion of modeling, but as part of a complete strategy for determining when and if arcs will occur, and preventing them from occurring in space.

Evaluation of variability and quality control procedures for a receptor-binding assay for paralytic shellfish poisoning toxins.

PubMed

Ruberu, S R; Langlois, G W; Masuda, M; Perera, S Kusum

2012-01-01

The receptor-binding assay (RBA) method for determining saxatoxin (STX) and its numerous analogues, which cause paralytic shellfish poisoning (PSP) in humans, was evaluated in a single laboratory study. Each step of the assay preparation procedure including the performance of the multi-detector TopCount® instrument was evaluated for its contribution to method variability. The overall inherent RBA variability was determined to be 17%. Variability within the 12 detectors was observed; however, there was no reproducible pattern in detector performance. This observed variability among detectors could be attributed to other factors, such as pipetting errors. In an attempt to reduce the number of plates rejected due to excessive variability in the method's quality control parameters, a statistical approach was evaluated using either Grubbs' test or the Student's t-test for rejecting outliers in the measurement of triplicate wells. This approach improved the ratio of accepted versus rejected plates, saving cost and time for rerunning the assay. However, the potential reduction in accuracy and the lack of improvement in precision suggests caution when using this approach. The current study has recommended an alternate quality control procedure for accepting or rejecting plates in place of the criteria currently used in the published assay, or the alternative of outlier testing. The recommended procedure involves the development of control charts to monitor the critical parameters identified in the published method (QC sample, EC₅₀, slope of calibration curve), with the addition of a fourth critical parameter which is the top value (100% binding) of the calibration curve.

Imputation of Test Scores in the National Education Longitudinal Study of 1988 (NELS:88). Working Paper Series.

ERIC Educational Resources Information Center

Bokossa, Maxime C.; Huang, Gary G.

This report describes the imputation procedures used to deal with missing data in the National Education Longitudinal Study of 1988 (NELS:88), the only current National Center for Education Statistics (NCES) dataset that contains scores from cognitive tests given the same set of students at multiple time points. As is inevitable, cognitive test…

76 FR 63211 - Energy Efficiency Program: Test Procedures for Residential Water Heaters, Direct Heating...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-12

..., sections 1.7 and 1.12. The definition for ``Storage-type Water Heater of More than 2 Gallons (7.6 Liters) and Less than 20 Gallons (76 Liters)'' is currently reserved. Id. at section 1.12.5. DOE is... another. In addition, these studies suggest that the existing draw pattern in the simulated use test may...

Effect of Surge Current Testing on Reliability of Solid Tantalum Capacitors

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander

2008-01-01

Tantalum capacitors manufactured per military specifications are established reliability components and have less than 0.001% of failures per 1000 hours for grades D or S, thus positioning these parts among electronic components with the highest reliability characteristics. Still, failures of tantalum capacitors do happen and when it occurs it might have catastrophic consequences for the system. To reduce this risk, further development of a screening and qualification system with special attention to the possible deficiencies in the existing procedures is necessary. The purpose of this work is evaluation of the effect of surge current stress testing on reliability of the parts at both steady-state and multiple surge current stress conditions. In order to reveal possible degradation and precipitate more failures, various part types were tested and stressed in the range of voltage and temperature conditions exceeding the specified limits. A model to estimate the probability of post-surge current testing-screening failures and measures to improve the effectiveness of the screening process has been suggested.

Sizing Single Cantilever Beam Specimens for Characterizing Facesheet/Core Peel Debonding in Sandwich Structure

NASA Technical Reports Server (NTRS)

Ratcliffe, James G.

2010-01-01

This paper details part of an effort focused on the development of a standardized facesheet/core peel debonding test procedure. The purpose of the test is to characterize facesheet/core peel in sandwich structure, accomplished through the measurement of the critical strain energy release rate associated with the debonding process. The specific test method selected for the standardized test procedure utilizes a single cantilever beam (SCB) specimen configuration. The objective of the current work is to develop a method for establishing SCB specimen dimensions. This is achieved by imposing specific limitations on specimen dimensions, with the objectives of promoting a linear elastic specimen response, and simplifying the data reduction method required for computing the critical strain energy release rate associated with debonding. The sizing method is also designed to be suitable for incorporation into a standardized test protocol. Preliminary application of the resulting sizing method yields practical specimen dimensions.

MRI-Guided Regional Personalized Electrical Stimulation in Multisession and Home Treatments

PubMed Central

Cancelli, Andrea; Cottone, Carlo; Giordani, Alessandro; Asta, Giampiero; Lupoi, Domenico; Pizzella, Vittorio; Tecchio, Franca

2018-01-01

The shape and position of the electrodes is a key factor for the efficacy of transcranial electrical stimulations (tES). We have recently introduced the Regional Personalized Electrode (RePE), a tES electrode fitting the personal cortical folding, that has been able to differentiate the stimulation of close by regions, in particular the primary sensory (S1) and motor (M1) cortices, and to personalize tES onto such an extended cortical district. However, neuronavigation on individual brain was compulsory for the correct montage. Here, we aimed at developing and testing a neuronavigation-free procedure for easy and quick positioning RePE, enabling multisession RePE-tES at home. We used off-line individual MRI to shape RePE via an ad-hoc computerized procedure, while an ad-hoc developed Adjustable Helmet Frame (AHF) was used to properly position it in multisession treatments, even at home. We used neuronavigation to test the RePE shape and position obtained by the new computerized procedure and the re-positioning obtained via the AHF. Using Finite Element Method (FEM) model, we also estimated the intra-cerebral current distribution induced by transcranial direct current stimulation (tDCS) comparing RePE vs. non-RePE with fixed reference. Additionally, we tested, using FEM, various shapes, and positions of the reference electrode taking into account possible small displacements of RePE, to test feasibility of RePE-tES sessions at home. The new RePE neuronavigation-free positioning relies on brain MRI space distances, and produced a mean displacement of 3.5 ± 0.8 mm, and the re-positioning of 4.8 ± 1.1 mm. Higher electric field in S1 than in M1 was best obtained with the occipital reference electrode, a montage that proved to feature low sensitivity to typical RePE millimetric displacements. Additionally, a new tES accessory was developed to enable repositioning the electrodes over the scalp also at home, with a precision which is acceptable according to the modeling-estimated intracerebral currents. Altogether, we provide here a procedure to simplify and make easily applicable RePE-tDCS, which enables efficacious personalized treatments. PMID:29867308

Design of an x-ray telescope optics for XEUS

NASA Astrophysics Data System (ADS)

Graue, Roland; Kampf, Dirk; Wallace, Kotska; Lumb, David; Bavdaz, Marcos; Freyberg, Michael

2017-11-01

The X-ray telescope concept for XEUS is based on an innovative high performance and light weight Silicon Pore Optics technology. The XEUS telescope is segmented into 16 radial, thermostable petals providing the rigid optical bench structure of the stand alone XRay High Precision Tandem Optics. A fully representative Form Fit Function (FFF) Model of one petal is currently under development to demonstrate the outstanding lightweight telescope capabilities with high optically effective area. Starting from the envisaged system performance the related tolerance budgets were derived. These petals are made from ceramics, i.e. CeSiC. The structural and thermal performance of the petal shall be reported. The stepwise alignment and integration procedure on petal level shall be described. The functional performance and environmental test verification plan of the Form Fit Function Model and the test set ups are described in this paper. In parallel to the running development activities the programmatic and technical issues wrt. the FM telescope MAIT with currently 1488 Tandem Optics are under investigation. Remote controlled robot supported assembly, simultaneous active alignment and verification testing and decentralised time effective integration procedures shall be illustrated.

Load rating and retrofit testing of bridge timber piles subjected to eccentric loading.

DOT National Transportation Integrated Search

2012-11-01

This report first evaluated the load rating procedure currently in use by the Illinois Department of Transportation (IDOT) for rating timber : piles supporting multiple-span, simply supported bridges. For simplicity, these piles are often rated under...

Curling and warping of concrete pavement: an investigation and proof of concept study : final report.

DOT National Transportation Integrated Search

2016-06-01

In Kansas, mechanically stabilized earth (MSE) retaining walls are typically backfilled with coarse aggregate. : Current backfill material testing procedures used by the Kansas Department of Transportation (KDOT) utilize on-site : observations for co...

Evaluation of the Human Host Range of Bovine and Porcine Viruses that may Contaminate Bovine Serum and Porcine Trypsin Used in the Manufacture of Biological Products

PubMed Central

Marcus-Sekura, Carol; Richardson, James C.; Harston, Rebecca K.; Sane, Nandini; Sheets, Rebecca L.

2011-01-01

Current U.S. requirements for testing cell substrates used in production of human biological products for contamination with bovine and porcine viruses are U.S. Department of Agriculture (USDA) 9CFR tests for bovine serum or porcine trypsin. 9CFR requires testing of bovine serum for seven specific viruses in six families (immunofluorescence) and at least 2 additional families non-specifically (cytopathicity and hemadsorption). 9CFR testing of porcine trypsin is for porcine parvovirus. Recent contaminations suggest these tests may not be sufficient. Assay sensitivity was not the issue for these contaminations that were caused by viruses/virus families not represented in the 9CFR screen. A detailed literature search was undertaken to determine which viruses that infect cattle or swine or bovine or porcine cells in culture also have human host range [ability to infect humans or human cells in culture] and to predict their detection by the currently used 9CFR procedures. There are more viruses of potential risk to biological products manufactured using bovine or porcine raw materials than are likely to be detected by 9CFR testing procedures; even within families, not all members would necessarily be detected. Testing gaps and alternative methodologies should be evaluated to continue to ensure safe, high quality human biologicals. PMID:22000165

Improved Use of Satellite Imagery to Forecast Hurricanes

NASA Technical Reports Server (NTRS)

Louis, Jean-Francois

2001-01-01

This project tested a novel method that uses satellite imagery to correct phase errors in the initial state for numerical weather prediction, applied to hurricane forecasts. The system was tested on hurricanes Guillermo (1997), Felicia (1997) and Iniki (1992). We compared the performance of the system with and without phase correction to a procedure that uses bogus data in the initial state, similar to current operational procedures. The phase correction keeps the hurricane on track in the analysis and is far superior to a system without phase correction. Compared to operational procedure, phase correction generates somewhat worse 3-day forecast of the hurricane track, but better forecast of intensity. It is believed that the phase correction module would work best in the context of 4-dimensional variational data assimilation. Very little modification to 4DVar would be required.

A comparison of recovery of virus from wastewaters by beef extract-Celite, ferric chloride, and filter concentration procedures.

PubMed

Dahling, D R; Wright, B A

1988-12-01

An improved concentration method using sample volumes as large as 1500 ml has been developed to monitor for viruses in wastewaters. Non-precipitating dry beef extract powder is added to wastewater samples to give a 3% concentration and mixed until dissolved. This is followed by the addition of Celite as a virus adsorbent. By manipulating pH, viruses are eluted from the Celite in small volumes of phosphate buffer. This procedure was further tested without the aid of the Celite additives using a precipitating beef extract powder and substituting FeCl3 as an alternate reagent for the Celite. Comparison testing was also made with the currently recommended cartridge and disc filter procedures. In all cases, the non-precipitating beef extract-Celite method gave higher recovery rates in highly polluted waters.

Standardization of Solar Mirror Reflectance Measurements - Round Robin Test: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyen, S.; Lupfert, E.; Fernandez-Garcia, A.

2010-10-01

Within the SolarPaces Task III standardization activities, DLR, CIEMAT, and NREL have concentrated on optimizing the procedure to measure the reflectance of solar mirrors. From this work, the laboratories have developed a clear definition of the method and requirements needed of commercial instruments for reliable reflectance results. A round robin test was performed between the three laboratories with samples that represent all of the commercial solar mirrors currently available for concentrating solar power (CSP) applications. The results show surprisingly large differences in hemispherical reflectance (sh) of 0.007 and specular reflectance (ss) of 0.004 between the laboratories. These differences indicate themore » importance of minimum instrument requirements and standardized procedures. Based on these results, the optimal procedure will be formulated and validated with a new round robin test in which a better accuracy is expected. Improved instruments and reference standards are needed to reach the necessary accuracy for cost and efficiency calculations.« less

International Round-Robin Testing of Bulk Thermoelectrics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hsin; Porter, Wallace D; Bottner, Harold

2011-11-01

Two international round-robin studies were conducted on transport properties measurements of bulk thermoelectric materials. The study discovered current measurement problems. In order to get ZT of a material four separate transport measurements must be taken. The round-robin study showed that among the four properties Seebeck coefficient is the one can be measured consistently. Electrical resistivity has +4-9% scatter. Thermal diffusivity has similar +5-10% scatter. The reliability of the above three properties can be improved by standardizing test procedures and enforcing system calibrations. The worst problem was found in specific heat measurements using DSC. The probability of making measurement error ismore » great due to the fact three separate runs must be taken to determine Cp and the baseline shift is always an issue for commercial DSC. It is suggest the Dulong Petit limit be always used as a guide line for Cp. Procedures have been developed to eliminate operator and system errors. The IEA-AMT annex is developing standard procedures for transport properties testing.« less

APEX/SPIN: a free test platform to measure speech intelligibility.

PubMed

Francart, Tom; Hofmann, Michael; Vanthornhout, Jonas; Van Deun, Lieselot; van Wieringen, Astrid; Wouters, Jan

2017-02-01

Measuring speech intelligibility in quiet and noise is important in clinical practice and research. An easy-to-use free software platform for conducting speech tests is presented, called APEX/SPIN. The APEX/SPIN platform allows the use of any speech material in combination with any noise. A graphical user interface provides control over a large range of parameters, such as number of loudspeakers, signal-to-noise ratio and parameters of the procedure. An easy-to-use graphical interface is provided for calibration and storage of calibration values. To validate the platform, perception of words in quiet and sentences in noise were measured both with APEX/SPIN and with an audiometer and CD player, which is a conventional setup in current clinical practice. Five normal-hearing listeners participated in the experimental evaluation. Speech perception results were similar for the APEX/SPIN platform and conventional procedures. APEX/SPIN is a freely available and open source platform that allows the administration of all kinds of custom speech perception tests and procedures.

Validation of alternative methods for toxicity testing.

PubMed Central

Bruner, L H; Carr, G J; Curren, R D; Chamberlain, M

1998-01-01

Before nonanimal toxicity tests may be officially accepted by regulatory agencies, it is generally agreed that the validity of the new methods must be demonstrated in an independent, scientifically sound validation program. Validation has been defined as the demonstration of the reliability and relevance of a test method for a particular purpose. This paper provides a brief review of the development of the theoretical aspects of the validation process and updates current thinking about objectively testing the performance of an alternative method in a validation study. Validation of alternative methods for eye irritation testing is a specific example illustrating important concepts. Although discussion focuses on the validation of alternative methods intended to replace current in vivo toxicity tests, the procedures can be used to assess the performance of alternative methods intended for other uses. Images Figure 1 PMID:9599695

Direct Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

EPA Pesticide Factsheets

This rule will adopt the current voluntary NOx and CO emissions standards of the United Nations International Civil Aviation Organization (ICAO), bringing the United States aircraft standards into alignment with the international standards.

Development of Tasks and Evaluation of a Prototype Forceps for NOTES

PubMed Central

Addis, Matthew; Aguirre, Milton; Haluck, Randy; Matthew, Abraham; Pauli, Eric; Gopal, Jegan

2012-01-01

Background and Objectives: Few standardized testing procedures exist for instruments intended for Natural Orifice Translumenal Endoscopic Surgery. These testing procedures are critical for evaluating surgical skills and surgical instruments to ensure sufficient quality. This need is widely recognized by endoscopic surgeons as a major hurdle for the advancement of Natural Orifice Translumenal Endoscopic Surgery. Methods: Beginning with tasks currently used to evaluate laparoscopic surgeons and instruments, new tasks were designed to evaluate endoscopic surgical forceps instruments. Results: Six tasks have been developed from existing tasks, adapted and modified for use with endoscopic instruments, or newly designed to test additional features of endoscopic forceps. The new tasks include the Fuzzy Ball Task, Cup Drop Task, Ring Around Task, Material Pull Task, Simulated Biopsy Task, and the Force Gauge Task. These tasks were then used to evaluate the performance of a new forceps instrument designed at Pennsylvania State University. Conclusions: The need for testing procedures for the advancement of Natural Orifice Translumenal Endoscopic Surgery has been addressed in this work. The developed tasks form a basis for not only testing new forceps instruments, but also for evaluating individual performance of surgical candidates with endoscopic forceps instruments. PMID:22906337

Solar panel acceptance testing using a pulsed solar simulator

NASA Technical Reports Server (NTRS)

Hershey, T. L.

1977-01-01

Utilizing specific parameters as area of an individual cell, number in series and parallel, and established coefficient of current and voltage temperature dependence, a solar array irradiated with one solar constant at AMO and at ambient temperature can be characterized by a current-voltage curve for different intensities, temperatures, and even different configurations. Calibration techniques include: uniformity in area, depth and time, absolute and transfer irradiance standards, dynamic and functional check out procedures. Typical data are given for individual cell (2x2 cm) to complete flat solar array (5x5 feet) with 2660 cells and on cylindrical test items with up to 10,000 cells. The time and energy saving of such testing techniques are emphasized.

Implementation Considerations for Multisite Clinical Trials with Cognitive Neuroscience Tasks

PubMed Central

Keefe, Richard S. E.; Harvey, Philip D.

2008-01-01

Multisite clinical trials aimed at cognitive enhancement across various neuropsychiatric conditions have employed standard neuropsychological tests as outcome measures. While these tests have enjoyed wide clinical use and have proven reliable and predictive of functional disability, a number of implementation challenges have arisen when these tests are used in clinical trials. These issues are likely to be magnified in future studies when cognitive neuroscience (CN) procedures are explored in these trials, because in their current forms CN procedures are less standardized and more difficult to teach and monitor. For multisite trials, we anticipate that the most challenging issues will include assuring tester competence, monitoring tester performance, specific challenges with complex assessment methods, and having resources available for adequate monitoring of data quality. Suggestions for overcoming these implementation challenges are offered. PMID:18495645

Initial Results from the Third Round of Remediated Nitrate Salt Surrogate Formulation and Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne; Leonard, Philip; Hartline, Ernest Leon

2016-04-20

High explosives science and technology (M-7) is currently working on the third round of formulation and testing of Remediated nitrate salt (RNS) surrogates. This report summarizes the calorimetry results from the 15% sWheat mixtures. All formulation and testing was carried out according to PLAN-TA9-2443 Rev B, "Remediated Nitrate Salt (RNS) surrogate formulation and testing standard procedure", released February 16, 2016. Results from the first and second rounds of formulation and testing were documented in memoranda M7-16-6042 and M7-16-6053.

Examining procedural working memory processing in obsessive-compulsive disorder.

PubMed

Shahar, Nitzan; Teodorescu, Andrei R; Anholt, Gideon E; Karmon-Presser, Anat; Meiran, Nachshon

2017-07-01

Previous research has suggested that a deficit in working memory might underlie the difficulty of obsessive-compulsive disorder (OCD) patients to control their thoughts and actions. However, a recent meta-analyses found only small effect sizes for working memory deficits in OCD. Recently, a distinction has been made between declarative and procedural working memory. Working memory in OCD was tested mostly using declarative measurements. However, OCD symptoms typically concerns actions, making procedural working-memory more relevant. Here, we tested the operation of procedural working memory in OCD. Participants with OCD and healthy controls performed a battery of choice reaction tasks under high and low procedural working memory demands. Reaction-times (RT) were estimated using ex-Gaussian distribution fitting, revealing no group differences in the size of the RT distribution tail (i.e., τ parameter), known to be sensitive to procedural working memory manipulations. Group differences, unrelated to working memory manipulations, were found in the leading-edge of the RT distribution and analyzed using a two-stage evidence accumulation model. Modeling results suggested that perceptual difficulties might underlie the current group differences. In conclusion, our results suggest that procedural working-memory processing is most likely intact in OCD, and raise a novel, yet untested assumption regarding perceptual deficits in OCD. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

JPRS Report, Science & Technology Europe

DTIC Science & Technology

1988-05-10

given environment essentially depends on three parameters ; these are: • the adhesion between the adhesive and the supports; • the cohesion of the...durability/CND J Electric current under high field/Tensile test at 4 degrees K I Synthetic hydroxyapatite /behavior under friction and wear GB NaCl, s...French programs GB Inventory of accelerated test procedures, correlation among parameters FC Influence of experimental parameters 8615 JPRS-EST-88

Test Operations Procedure (TOP) 2-2-650 Engine Cold-Starting and Warm-Up Tests

DTIC Science & Technology

2008-02-12

REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 ...currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1 . REPORT DATE (DD-MM-YYYY) 12-02-2008 2. REPORT...Page Paragraph 1 . SCOPE................................................................................ 2 2. FACILITIES AND INSTRUMENTATION

Portable Body Temperature Conditioner

DTIC Science & Technology

2014-12-01

are homeothermic and require a narrow core body temperature range to maintain normal homeostasis. Currently, the most effective treatments for...for monitoring circulating water and patient body temperature . During breadboard testing the effectiveness of the air coil was found to be...blanket. Bath temperatures were set to 30°C, 15°C, and 10°C respectively. In order to develop a testing procedure for quantifying the effective

Automated processing of endoscopic surgical instruments.

PubMed

Roth, K; Sieber, J P; Schrimm, H; Heeg, P; Buess, G

1994-10-01

This paper deals with the requirements for automated processing of endoscopic surgical instruments. After a brief analysis of the current problems, solutions are discussed. Test-procedures have been developed to validate the automated processing, so that the cleaning results are guaranteed and reproducable. Also a device for testing and cleaning was designed together with Netzsch Newamatic and PCI, called TC-MIC, to automate processing and reduce manual work.

Determination of Mercury in Aqueous and Geologic Materials by Continuous Flow-Cold Vapor-Atomic Fluorescence Spectrometry (CVAFS)

USGS Publications Warehouse

Hageman, Philip L.

2007-01-01

New methods for the determination of total mercury in geologic materials and dissolved mercury in aqueous samples have been developed that will replace the methods currently (2006) in use. The new methods eliminate the use of sodium dichromate (Na2Cr2O7 ?2H2O) as an oxidizer and preservative and significantly lower the detection limit for geologic and aqueous samples. The new methods also update instrumentation from the traditional use of cold vapor-atomic absorption spectrometry to cold vapor-atomic fluorescence spectrometry. At the same time, the new digestion procedures for geologic materials use the same size test tubes, and the same aluminum heating block and hot plate as required by the current methods. New procedures for collecting and processing of aqueous samples use the same procedures that are currently (2006) in use except that the samples are now preserved with concentrated hydrochloric acid/bromine monochloride instead of sodium dichromate/nitric acid. Both the 'old' and new methods have the same analyst productivity rates. These similarities should permit easy migration to the new methods. Analysis of geologic and aqueous reference standards using the new methods show that these procedures provide mercury recoveries that are as good as or better than the previously used methods.

Fault tolerant system based on IDDQ testing

NASA Astrophysics Data System (ADS)

Guibane, Badi; Hamdi, Belgacem; Mtibaa, Abdellatif; Bensalem, Brahim

2018-06-01

Offline test is essential to ensure good manufacturing quality. However, for permanent or transient faults that occur during the use of the integrated circuit in an application, an online integrated test is needed as well. This procedure should ensure the detection and possibly the correction or the masking of these faults. This requirement of self-correction is sometimes necessary, especially in critical applications that require high security such as automotive, space or biomedical applications. We propose a fault-tolerant design for analogue and mixed-signal design complementary metal oxide (CMOS) circuits based on the quiescent current supply (IDDQ) testing. A defect can cause an increase in current consumption. IDDQ testing technique is based on the measurement of power supply current to distinguish between functional and failed circuits. The technique has been an effective testing method for detecting physical defects such as gate-oxide shorts, floating gates (open) and bridging defects in CMOS integrated circuits. An architecture called BICS (Built In Current Sensor) is used for monitoring the supply current (IDDQ) of the connected integrated circuit. If the measured current is not within the normal range, a defect is signalled and the system switches connection from the defective to a functional integrated circuit. The fault-tolerant technique is composed essentially by a double mirror built-in current sensor, allowing the detection of abnormal current consumption and blocks allowing the connection to redundant circuits, if a defect occurs. Spices simulations are performed to valid the proposed design.

Short- and long-term effects of clinical audits on compliance with procedures in CT scanning.

PubMed

Oliveri, Antonio; Howarth, Nigel; Gevenois, Pierre Alain; Tack, Denis

2016-08-01

To test the hypothesis that quality clinical audits improve compliance with the procedures in computed tomography (CT) scanning. This retrospective study was conducted in two hospitals, based on 6950 examinations and four procedures, focusing on the acquisition length in lumbar spine CT, the default tube current applied in abdominal un-enhanced CT, the tube potential selection for portal phase abdominal CT and the use of a specific "paediatric brain CT" procedure. The first clinical audit reported compliance with these procedures. After presenting the results to the stakeholders, a second audit was conducted to measure the impact of this information on compliance and was repeated the next year. Comparisons of proportions were performed using the Chi-square Pearson test. Depending on the procedure, the compliance rate ranged from 27 to 88 % during the first audit. After presentation of the audit results to the stakeholders, the compliance rate ranged from 68 to 93 % and was significantly improved for all procedures (P ranging from <0.001 to 0.031) in both hospitals and remained unchanged during the third audit (P ranging from 0.114 to 0.999). Quality improvement through repeated compliance audits with CT procedures durably improves this compliance. • Compliance with CT procedures is operator-dependent and not perfect. • Compliance differs between procedures and hospitals, even within a unified department. • Compliance is improved through audits followed by communication to the stakeholders. • This improvement is sustainable over a one-year period.

Development of mix design procedures for gap-graded asphalt-rubber asphalt concrete

DOT National Transportation Integrated Search

2007-11-01

A research project was conducted to identify and document current modifications to ARIZONA 815c (75-blow Marshall method) used to develop gap-graded asphalt rubber asphalt concrete (GG AR AC) mix designs, and to develop and test improvements to provi...

Development of a TL-3 deep beam tubular backup bridge rail : executive summary report.

DOT National Transportation Integrated Search

2010-12-01

Ohio Department of Transportation (ODOT)s Office of Structural Engineering has a need to evaluate and, if necessary, improve an existing bridge rail design with a simple retrofitting procedure to meet current or proposed crash testing standards. T...

A unified framework for developing effective hygiene procedures for hands, environmental surfaces and laundry in healthcare, domestic, food handling and other settings

PubMed Central

Bloomfield, Sally F.; Carling, Philip C.; Exner, Martin

2017-01-01

Hygiene procedures for hands, surfaces and fabrics are central to preventing spread of infection in settings including healthcare, food production, catering, agriculture, public settings, and home and everyday life. They are used in situations including hand hygiene, clinical procedures, decontamination of environmental surfaces, respiratory hygiene, food handling, laundry hygiene, toilet hygiene and so on. Although the principles are common to all, approaches currently used in different settings are inconsistent. A concern is the use of inconsistent terminology which is misleading, especially to people we need to communicate with such as the public or cleaning professionals. This paper reviews the data on current approaches, alongside new insights to developing hygiene procedures. Using this data, we propose a more scientifically-grounded framework for developing procedures that maximize protection against infection, based on consistent principles and terminology, and applicable across all settings. A key feature is use of test models which assess the state of surfaces after treatment rather than product performance alone. This allows procedures that rely on removal of microbes to be compared with those employing chemical or thermal inactivation. This makes it possible to ensure that a consistent “safety target level” is achieved regardless of the type of procedure used, and allows us deliver maximum health benefit whilst ensuring prudent usage of antimicrobial agents, detergents, water and energy. PMID:28670508

Immunity to human cytomegalovirus measured and compared by complement fixation, indirect fluorescent-antibody, indirect hemagglutination, and enzyme-linked immunosorbent assays.

PubMed Central

Brandt, J A; Kettering, J D; Lewis, J E

1984-01-01

The complement fixation test is currently the test employed most frequently to determine the presence of antibody to human cytomegalovirus. Several other techniques have been adapted for this purpose. A comparison of cytomegalovirus antibody titers was made between the complement fixation test, a commercially available enzyme-linked immunosorbent assay, an indirect immunofluorescent technique, and a modified indirect hemagglutination test. Forty-three serum samples were tested for antibodies by each of the above procedures. The enzyme-linked immunosorbent, immunofluorescent, and indirect hemagglutination assays were in close agreement on all samples tested; the titers obtained with these methods were all equal to or greater than the complement fixation titer for 38 of the 41 samples (92.6%). Two samples were anticomplementary in the complement fixation test but gave readable results in the other tests. The complement fixation test was the least sensitive of the procedures examined. The commercial enzyme-linked immunosorbent assay system was the most practical method and offered the highest degree of sensitivity in detecting antibodies to cytomegalovirus. PMID:6321544

Investigation of the effects of external current systems on the MAGSAT data utilizing grid cell modeling techniques

NASA Technical Reports Server (NTRS)

Klumpar, D. M. (Principal Investigator)

1982-01-01

Efforts in support of the development of a model of the magnetic fields due to ionospheric and magnetospheric electrical currents are discussed. Specifically, progress made in reading MAGSAT tapes and plotting the deviation of the measured magnetic field components with respect to a spherical harmonic model of the main geomagnetic field is reported. Initial tests of the modeling procedure developed to compute the ionosphere/magnetosphere-induced fields at satellite orbit are also described. The modeling technique utilizes a liner current element representation of the large scale current system.

Laboratory performance evaluation of CIR-emulsion and its comparison against CIR-foam test results from phase III.

DOT National Transportation Integrated Search

2009-12-01

Currently, no standard mix design procedure is available for CIR-emulsion in Iowa. The CIR-foam mix : design process developed during the previous phase is applied for CIR-emulsion mixtures with varying : emulsified asphalt contents. Dynamic modulus ...

Validity and Reliability of the School Physical Activity Environment Questionnaire

ERIC Educational Resources Information Center

Martin, Jeffrey J.; McCaughtry, Nate; Flory, Sara; Murphy, Anne; Wisdom, Kimberlydawn

2011-01-01

The goal of the current study was to establish the factor validity of the Questionnaire Assessing School Physical Activity Environment (Robertson-Wilson, Levesque, & Holden, 2007) using confirmatory factor analysis procedures. Another goal was to establish internal reliability and test-retest reliability. The confirmatory factor analysis…

Non-Destructive Evaluation of Aerospace Composites

DTIC Science & Technology

2009-03-01

security as well as non-invasive epithelial and breast cancer detection [3, 23]. Figure 8 shows a pair of examples of current THz imaging systems...conduction videos; each test lasting approximately 10 seconds. 3.3.2 Thermography Procedure The samples were set flat on two wooden slats to

10 CFR 431.282 - Test Procedures [Reserved

Code of Federal Regulations, 2010 CFR

2010-01-01

..., metal halide, and high-pressure sodium lamps. Mercury vapor lamp means a high intensity discharge lamp..., current, and waveform) for starting and operating. High intensity discharge lamp means an electric... light is produced by radiation from mercury typically operating at a partial vapor pressure in excess of...

A simple randomisation procedure for validating discriminant analysis: a methodological note.

PubMed

Wastell, D G

1987-04-01

Because the goal of discriminant analysis (DA) is to optimise classification, it designedly exaggerates between-group differences. This bias complicates validation of DA. Jack-knifing has been used for validation but is inappropriate when stepwise selection (SWDA) is employed. A simple randomisation test is presented which is shown to give correct decisions for SWDA. The general superiority of randomisation tests over orthodox significance tests is discussed. Current work on non-parametric methods of estimating the error rates of prediction rules is briefly reviewed.

Operational Based Vision Assessment Cone Contrast Test: Description and Operation

DTIC Science & Technology

2016-06-02

Jun 2016. Report contains color . 14. ABSTRACT The work detailed in this report was conducted by the Operational Based Vision Assessment (OBVA...currently used by the Air Force for aircrew color vision screening. The new OBVA CCT is differentiated from the Rabin device primarily by hardware...test procedures, and analysis techniques. Like the Rabin CCT, the OBVA CCT uses colors that selectively stimulate the cone photoreceptors of the

Network-Based Method for Identifying Co-Regeneration Genes in Bone, Dentin, Nerve and Vessel Tissues

PubMed Central

Pan, Hongying; Zhang, Yu-Hang; Feng, Kaiyan; Kong, XiangYin; Cai, Yu-Dong

2017-01-01

Bone and dental diseases are serious public health problems. Most current clinical treatments for these diseases can produce side effects. Regeneration is a promising therapy for bone and dental diseases, yielding natural tissue recovery with few side effects. Because soft tissues inside the bone and dentin are densely populated with nerves and vessels, the study of bone and dentin regeneration should also consider the co-regeneration of nerves and vessels. In this study, a network-based method to identify co-regeneration genes for bone, dentin, nerve and vessel was constructed based on an extensive network of protein–protein interactions. Three procedures were applied in the network-based method. The first procedure, searching, sought the shortest paths connecting regeneration genes of one tissue type with regeneration genes of other tissues, thereby extracting possible co-regeneration genes. The second procedure, testing, employed a permutation test to evaluate whether possible genes were false discoveries; these genes were excluded by the testing procedure. The last procedure, screening, employed two rules, the betweenness ratio rule and interaction score rule, to select the most essential genes. A total of seventeen genes were inferred by the method, which were deemed to contribute to co-regeneration of at least two tissues. All these seventeen genes were extensively discussed to validate the utility of the method. PMID:28974058

Network-Based Method for Identifying Co- Regeneration Genes in Bone, Dentin, Nerve and Vessel Tissues.

PubMed

Chen, Lei; Pan, Hongying; Zhang, Yu-Hang; Feng, Kaiyan; Kong, XiangYin; Huang, Tao; Cai, Yu-Dong

2017-10-02

Bone and dental diseases are serious public health problems. Most current clinical treatments for these diseases can produce side effects. Regeneration is a promising therapy for bone and dental diseases, yielding natural tissue recovery with few side effects. Because soft tissues inside the bone and dentin are densely populated with nerves and vessels, the study of bone and dentin regeneration should also consider the co-regeneration of nerves and vessels. In this study, a network-based method to identify co-regeneration genes for bone, dentin, nerve and vessel was constructed based on an extensive network of protein-protein interactions. Three procedures were applied in the network-based method. The first procedure, searching, sought the shortest paths connecting regeneration genes of one tissue type with regeneration genes of other tissues, thereby extracting possible co-regeneration genes. The second procedure, testing, employed a permutation test to evaluate whether possible genes were false discoveries; these genes were excluded by the testing procedure. The last procedure, screening, employed two rules, the betweenness ratio rule and interaction score rule, to select the most essential genes. A total of seventeen genes were inferred by the method, which were deemed to contribute to co-regeneration of at least two tissues. All these seventeen genes were extensively discussed to validate the utility of the method.

An automatic identification procedure to promote the use of FES-cycling training for hemiparetic patients.

PubMed

Ambrosini, Emilia; Ferrante, Simona; Schauer, Thomas; Ferrigno, Giancarlo; Molteni, Franco; Pedrocchi, Alessandra

2014-01-01

Cycling induced by Functional Electrical Stimulation (FES) training currently requires a manual setting of different parameters, which is a time-consuming and scarcely repeatable procedure. We proposed an automatic procedure for setting session-specific parameters optimized for hemiparetic patients. This procedure consisted of the identification of the stimulation strategy as the angular ranges during which FES drove the motion, the comparison between the identified strategy and the physiological muscular activation strategy, and the setting of the pulse amplitude and duration of each stimulated muscle. Preliminary trials on 10 healthy volunteers helped define the procedure. Feasibility tests on 8 hemiparetic patients (5 stroke, 3 traumatic brain injury) were performed. The procedure maximized the motor output within the tolerance constraint, identified a biomimetic strategy in 6 patients, and always lasted less than 5 minutes. Its reasonable duration and automatic nature make the procedure usable at the beginning of every training session, potentially enhancing the performance of FES-cycling training.

WIPP waste characterization program sampling and analysis guidance manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-01-01

The Waste Isolation Pilot Plant (WIPP) Waste Characterization Program Sampling and Analysis Guidance Manual (Guidance Manual) provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Quality Assurance Program Plan (QAPP) for the WIPP Experimental-Waste Characterization Program (the Program). This Guidance Manual includes all of the sampling and testing methodologies accepted by the WIPP Project Office (DOE/WPO) for use in implementing the Program requirements specified in the QAPP. This includes methods for characterizing representative samples of transuranic (TRU) wastesmore » at DOE generator sites with respect to the gas generation controlling variables defined in the WIPP bin-scale and alcove test plans, as well as waste container headspace gas sampling and analytical procedures to support waste characterization requirements under the WIPP test program and the Resource Conservation and Recovery Act (RCRA). The procedures in this Guidance Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site specific procedures. The use of these procedures is intended to provide the necessary sensitivity, specificity, precision, and comparability of analyses and test results. The solutions to achieving specific program objectives will depend upon facility constraints, compliance with DOE Orders and DOE facilities' operating contractor requirements, and the knowledge and experience of the TRU waste handlers and analysts. With some analytical methods, such as gas chromatography/mass spectrometry, the Guidance Manual procedures may be used directly. With other methods, such as nondestructive/destructive characterization, the Guidance Manual provides guidance rather than a step-by-step procedure.« less

Development of Inspection for Friction Stir Welds for Rocket Fuel Tanks

NASA Technical Reports Server (NTRS)

Russell, Samuel S.

2012-01-01

During development of the Ares I weld processes nondestructive and destructive testing were used to identify and characterize defects that occurred. These defects were named and character noted. This catalogue of defects and characteristics was then used to develop inspection methods for Self Reacting Friction Stir Welds (SR ]FSW) and Conventional Friction Stir Welds (C ]FSW). Dye penetrant, eddy current, x ]radiography, single element ultrasonic, and phased array ultrasonic (PAUT) inspection procedures were developed to target the expected defects. Once the method procedure was developed a comparison was performed to allow for selection of the best inspection method. Tests of the effectiveness of the inspection were performed on purposely fabricated flawed specimens and electrodischarge machined notches. The initial test results prompted a revisit of the PAUT procedure and a redesign of the inspection. Subsequent testing showed that a multi ]angle PAUT inspection resulted in better detection capability. A discussion of the most effective orientations of the PAUT transducer will be presented. Also, the implementation of the inspection on production hardware will be presented. In some cases the weld tool is used as the transducer manipulator and in some cases a portable scanner is used

European guidelines for workplace drug testing in oral fluid.

PubMed

Brcak, Michaela; Beck, Olof; Bosch, Tessa; Carmichael, Duncan; Fucci, Nadia; George, Claire; Piper, Mark; Salomone, Alberto; Schielen, Wim; Steinmeyer, Stefan; Taskinen, Sanna; Weinmann, Wolfgang

2018-03-01

These guidelines for Legally Defensible Workplace Drug Testing have been prepared and updated by the European Workplace Drug Testing Society (EWDTS). The European Guidelines are designed to establish best practice procedures whilst allowing individual countries to operate within the requirements of national customs and legislation. The EWDTS recommends that all European laboratories that undertake legally defensible workplace drug testing should use these guidelines as a template for accreditation. These guidelines are relevant to laboratory-based testing only. These guidelines follow current best practices and are constantly under review. Copyright © 2017 John Wiley & Sons, Ltd.

8s, a numerical simulator of the challenging optical calibration of the E-ELT adaptive mirror M4

NASA Astrophysics Data System (ADS)

Briguglio, Runa; Pariani, Giorgio; Xompero, Marco; Riccardi, Armando; Tintori, Matteo; Lazzarini, Paolo; Spanò, Paolo

2016-07-01

8s stands for Optical Test TOwer Simulator (with 8 read as in italian 'otto'): it is a simulation tool for the optical calibration of the E-ELT deformable mirror M4 on its test facility. It has been developed to identify possible criticalities in the procedure, evaluate the solutions and estimate the sensitivity to environmental noise. The simulation system is composed by the finite elements model of the tower, the analytic influence functions of the actuators, the ray tracing propagation of the laser beam through the optical surfaces. The tool delivers simulated phasemaps of M4, associated with the current system status: actuator commands, optics alignment and position, beam vignetting, bench temperature and vibrations. It is possible to simulate a single step of the optical test of M4 by changing the system parameters according to a calibration procedure and collect the associated phasemap for performance evaluation. In this paper we will describe the simulation package and outline the proposed calibration procedure of M4.

A Procedural Electroencephalogram Simulator for Evaluation of Anesthesia Monitors.

PubMed

Petersen, Christian Leth; Görges, Matthias; Massey, Roslyn; Dumont, Guy Albert; Ansermino, J Mark

2016-11-01

Recent research and advances in the automation of anesthesia are driving the need to better understand electroencephalogram (EEG)-based anesthesia end points and to test the performance of anesthesia monitors. This effort is currently limited by the need to collect raw EEG data directly from patients. A procedural method to synthesize EEG signals was implemented in a mobile software application. The application is capable of sending the simulated signal to an anesthesia depth of hypnosis monitor. Systematic sweeps of the simulator generate functional monitor response profiles reminiscent of how network analyzers are used to test electronic components. Three commercial anesthesia monitors (Entropy, NeuroSENSE, and BIS) were compared with this new technology, and significant response and feature variations between the monitor models were observed; this includes reproducible, nonmonotonic apparent multistate behavior and significant hysteresis at light levels of anesthesia. Anesthesia monitor response to a procedural simulator can reveal significant differences in internal signal processing algorithms. The ability to synthesize EEG signals at different anesthetic depths potentially provides a new method for systematically testing EEG-based monitors and automated anesthesia systems with all sensor hardware fully operational before human trials.

Building a Case for Blocks as Kindergarten Mathematics Learning Tools

ERIC Educational Resources Information Center

Kinzer, Cathy; Gerhardt, Kacie; Coca, Nicole

2016-01-01

Kindergarteners need access to blocks as thinking tools to develop, model, test, and articulate their mathematical ideas. In the current educational landscape, resources such as blocks are being pushed to the side and being replaced by procedural worksheets and academic "seat time" in order to address standards. Mathematics research…

Assessing the Complexity of Students' Knowledge in Chemistry

ERIC Educational Resources Information Center

Bernholt, Sascha; Parchmann, Ilka

2011-01-01

Current reforms in the education policy of various countries are intended to produce a paradigm shift in the educational system towards an outcome orientation. After implementing educational standards as normative objectives, the development of test procedures that adequately reflect these targets and standards is a central problem. This paper…

A Matter of Exposition: Examination and Education

ERIC Educational Resources Information Center

Schröder, Sabrina; Thompson, Christiane

2015-01-01

While current literature on examination and testing mostly engages with the objectivity of exams and their procedural logic, this article is concerned with the 'ethical dimension' of examination: Examinations provoke a particular relation to oneself, possibly self-transformation. The praxis of examination entails self-confrontation in the light of…

Poorly Performing Physicians: Does the Script Concordance Test Detect Bad Clinical Reasoning?

ERIC Educational Resources Information Center

Goulet, Francois; Jacques, Andre; Gagnon, Robert; Charlin, Bernard; Shabah, Abdo

2010-01-01

Introduction: Evaluation of poorly performing physicians is a worldwide concern for licensing bodies. The College des Medecins du Quebec currently assesses the clinical competence of physicians previously identified with potential clinical competence difficulties through a day-long procedure called the Structured Oral Interview (SOI). Two peer…

Tethered acoustic doppler current profiler platforms for measuring streamflow

USGS Publications Warehouse

Rehmel, Michael S.; Stewart, James A.; Morlock, Scott E.

2003-01-01

A tethered-platform design with a trimaran hull and 900-megahertz radio modems is now commercially available. Continued field use has resulted in U.S. Geological Survey procedures for making tethered-platform discharge measurements, including methods for tethered-boat deployment, moving-bed tests, and measurement of edge distances.

Field testing a mobile inelastic neutron scattering system to measure soil carbon

USDA-ARS?s Scientific Manuscript database

Cropping history in conjunction with soil management practices can have a major impact on the amount of organic carbon (C) stored in soil. Current methods of assessing soil C based on soil coring and subsequent processing procedures prior to laboratory analysis are labor intensive and time consuming...

Meta-Analysis of Academic Interventions Derived from Neuropsychological Data

ERIC Educational Resources Information Center

Burns, Matthew K.; Petersen-Brown, Shawna; Haegele, Katherine; Rodriguez, Megan; Schmitt, Braden; Cooper, Maureen; Clayton, Kate; Hutcheson, Shannon; Conner, Cynthia; Hosp, John; VanDerHeyden, Amanda M.

2016-01-01

Several scholars have recommended using data from neuropsychological tests to develop interventions for reading and mathematics. The current study examined the effects of using neuropsychological data within the intervention process with meta-analytic procedures. A total of 1,126 articles were found from an electronic search and compared to…

40 CFR 146.14 - Information to be considered by the Director.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., logging procedures, deviation checks, and a drilling, testing, and coring program; and (16) A certificate... information listed below which are current and accurate in the file. For a newly drilled Class I well, the..., construction, date drilled, location, depth, record of plugging and/or completion, and any additional...

Evaluation of initial subgrade variability on the Ohio SHRP test road : interim report for continued monitoring of instrumented pavement in Ohio.

DOT National Transportation Integrated Search

2000-01-01

The Ohio Department of Transportation (ODOT) currently uses density and moisture measured with a nuclear density gauge as the principal criteria for approving subgrade construction in Ohio. This procedure is time consuming, thereby restricting the nu...

40 CFR Appendix 1 to Subpart A of... - Static Sheen Test

Code of Federal Regulations, 2010 CFR

2010-07-01

... drilling fluids, drill cuttings, produced sand, and well treatment, completion and workover fluids. “Free... drill cuttings or produced sand are introduced into ambient seawater in a container having an air-to... specified. 6. Quality Control Procedures None currently specified. 7. Sample Collection and Handling 7...

Analytic Validation of Immunohistochemistry Assays: New Benchmark Data From a Survey of 1085 Laboratories.

PubMed

Stuart, Lauren N; Volmar, Keith E; Nowak, Jan A; Fatheree, Lisa A; Souers, Rhona J; Fitzgibbons, Patrick L; Goldsmith, Jeffrey D; Astles, J Rex; Nakhleh, Raouf E

2017-09-01

- A cooperative agreement between the College of American Pathologists (CAP) and the United States Centers for Disease Control and Prevention was undertaken to measure laboratories' awareness and implementation of an evidence-based laboratory practice guideline (LPG) on immunohistochemical (IHC) validation practices published in 2014. - To establish new benchmark data on IHC laboratory practices. - A 2015 survey on IHC assay validation practices was sent to laboratories subscribed to specific CAP proficiency testing programs and to additional nonsubscribing laboratories that perform IHC testing. Specific questions were designed to capture laboratory practices not addressed in a 2010 survey. - The analysis was based on responses from 1085 laboratories that perform IHC staining. Ninety-six percent (809 of 844) always documented validation of IHC assays. Sixty percent (648 of 1078) had separate procedures for predictive and nonpredictive markers, 42.7% (220 of 515) had procedures for laboratory-developed tests, 50% (349 of 697) had procedures for testing cytologic specimens, and 46.2% (363 of 785) had procedures for testing decalcified specimens. Minimum case numbers were specified by 85.9% (720 of 838) of laboratories for nonpredictive markers and 76% (584 of 768) for predictive markers. Median concordance requirements were 95% for both types. For initial validation, 75.4% (538 of 714) of laboratories adopted the 20-case minimum for nonpredictive markers and 45.9% (266 of 579) adopted the 40-case minimum for predictive markers as outlined in the 2014 LPG. The most common method for validation was correlation with morphology and expected results. Laboratories also reported which assay changes necessitated revalidation and their minimum case requirements. - Benchmark data on current IHC validation practices and procedures may help laboratories understand the issues and influence further refinement of LPG recommendations.

Statistical analysis of particle trajectories in living cells

NASA Astrophysics Data System (ADS)

Briane, Vincent; Kervrann, Charles; Vimond, Myriam

2018-06-01

Recent advances in molecular biology and fluorescence microscopy imaging have made possible the inference of the dynamics of molecules in living cells. Such inference allows us to understand and determine the organization and function of the cell. The trajectories of particles (e.g., biomolecules) in living cells, computed with the help of object tracking methods, can be modeled with diffusion processes. Three types of diffusion are considered: (i) free diffusion, (ii) subdiffusion, and (iii) superdiffusion. The mean-square displacement (MSD) is generally used to discriminate the three types of particle dynamics. We propose here a nonparametric three-decision test as an alternative to the MSD method. The rejection of the null hypothesis, i.e., free diffusion, is accompanied by claims of the direction of the alternative (subdiffusion or superdiffusion). We study the asymptotic behavior of the test statistic under the null hypothesis and under parametric alternatives which are currently considered in the biophysics literature. In addition, we adapt the multiple-testing procedure of Benjamini and Hochberg to fit with the three-decision-test setting, in order to apply the test procedure to a collection of independent trajectories. The performance of our procedure is much better than the MSD method as confirmed by Monte Carlo experiments. The method is demonstrated on real data sets corresponding to protein dynamics observed in fluorescence microscopy.

A survey of deans and ADEA activities on dental licensure issues.

PubMed

Ranney, Richard R; Haden, N Karl; Weaver, Richard W; Valachovic, Richard W

2003-10-01

A written survey on issues in clinical testing for licensure was sent to the deans of all dental schools in the United States. Response rate was 89 percent. Results indicate that administrative leaders of the country's dental schools think that third-party evaluation of graduates is appropriate, but they do not have confidence in current clinical tests for licensure. More than nine out of ten respondents indicated that change was needed in current testing procedures, and 82 percent thought the tests as currently conducted were not valid for decision purposes. Regional differences existed among the responses, with the least dissatisfaction occurring in the West. The highest-rated and most frequently mentioned reasons for dissatisfaction with clinical tests were the involvement of patients (human subjects) as currently done. Most respondents favored a national level for licensure tests, although the majority also approved of the recently enacted New York law that permits completion of a postgraduate year in an accredited program to substitute for clinical testing. Respondents indicated a belief that a national database on academic measures as compared to outcomes on clinical licensure tests would be useful, with overall grade point average or class rank as the favored academic measure. Informed by the recommendations of its representatives to the AADE-ADEA Innovative Testing and Educational Methodologies Committee and results of the survey of deans, ADEA is pursuing steps to foster change in the clinical licensure process.

Current maternal age recommendations for prenatal diagnosis: a reappraisal using the expected utility theory.

PubMed

Sicherman, N; Bombard, A T; Rappoport, P

1995-01-01

The expected utility theory suggests eliminating an age-specific criterion for recommending prenatal diagnosis to patients. We isolate the factors which patients and physicians need to consider intelligently in prenatal diagnosis, and show that the sole use of a threshold age as a screening device is inadequate. Such a threshold fails to consider adequately patients' attitudes regarding many of the possible outcomes of prenatal diagnosis; in particular, the birth of a chromosomally abnormal child and procedural-related miscarriages. It also precludes testing younger women and encourages testing in patients who do not necessarily require or desire it. All pregnant women should be informed about their prenatal diagnosis options, screening techniques, and diagnostic procedures, including their respective limitations, risks, and benefits.

Concentrator hot-spot testing, phase 1

NASA Technical Reports Server (NTRS)

Gonzalez, C. C.

1987-01-01

Results of a study to determine the hot-spot susceptibility of concentrator cells, to provide a hot-spot qualification test for concentrator modules, and to provide guidelines for reducing hot-spot susceptibility are presented. Hot-spot heating occurs in a photovoltaic module when the short-circuit current of a cell is lower than the string operating current forcing the cell into reverse bias with a concurrent power dissipation. Although the basis for the concentrator module hot-spot qualification test is the test developed for flat-plate modules, issues, such as providing cell illumination, introduce additional complexities into the testing procedure. The same general guidelines apply for protecting concentrator modules from hot-spot stressing as apply to flat-plate modules. Therefore, recommendations are made on the number of bypass diodes required per given number of series cells per module or source circuit. In addition, a new method for determining the cell temperature in the laboratory or in the field is discussed.

Antegrade continence enemas improve quality of life in patients with medically-refractory encopresis.

PubMed

Church, Joseph T; Simha, Sidd; Wild, Laurie C; Teitelbaum, Daniel H; Ehrlich, Peter F

2017-05-01

Fecal incontinence is a socially debilitating problem for many children. We hypothesized that in selected patients with medically-refractory encopresis, placement of an appendicostomy or cecostomy tube for administration of antegrade continence enemas (ACE) would improve quality of life (QOL). We reviewed all patients with encopresis who underwent appendicostomy or cecostomy placement from 2003 to 2014 at our institution. We contacted subjects' parents by phone and administered 3 surveys: a survey reflecting current stooling habits, a disease-specific QOL survey, and the PedsQL™ QOL survey. QOL surveys were completed twice by parents, once reflecting pre-operative QOL, then again reflecting current QOL. Pre-procedure and post-procedure scores were compared by paired t-test. Ten patients underwent appendicostomy/cecostomy for encopresis. Eight completed phone surveys. All procedures were performed laparoscopically. All patients experienced fecal soiling pre-operatively, whereas 5/8 surveyed patients (63%) noted complete resolution of soiling post-procedure (p<0.01). General and disease-specific QOL improved from pre-procedure to post-procedure in the following domains: social habits, physical activity, ability to spend the night elsewhere, feeling, and overall QOL (p<0.05). PedsQL™ scores improved significantly in physical functioning, social functioning, and overall functioning (p<0.05). Antegrade continence enemas significantly improve quality of life in patients with medically-refractory encopresis, likely related to resolution of soiling. 4. Copyright © 2017. Published by Elsevier Inc.

Delayed flap approach procedures for noise abatement and fuel conservation

NASA Technical Reports Server (NTRS)

Edwards, F. G.; Bull, J. S.; Foster, J. D.; Hegarty, D. M.; Drinkwater, F. J., III

1976-01-01

The NASA/Ames Research Center is currently investigating the delayed flap approach during which pilot actions are determined and prescribed by an onboard digital computer. The onboard digital computer determines the proper timing for the deployment of the landing gear and flaps based on the existing winds and airplane gross weight. Advisory commands are displayed to the pilot. The approach is flown along the conventional ILS glide slope but is initiated at a higher airspeed and in a clean aircraft configuration that allows for low thrust and results in reduced noise and fuel consumption. Topics discussed include operational procedures, pilot acceptability of these procedures, and fuel/noise benefits resulting from flight tests and simulation.

Comparing preference assessments: selection- versus duration-based preference assessment procedures.

PubMed

Kodak, Tiffany; Fisher, Wayne W; Kelley, Michael E; Kisamore, April

2009-01-01

In the current investigation, the results of a selection- and a duration-based preference assessment procedure were compared. A Multiple Stimulus With Replacement (MSW) preference assessment [Windsor, J., Piché, L. M., & Locke, P. A. (1994). Preference testing: A comparison of two presentation methods. Research in Developmental Disabilities, 15, 439-455] and a variation of a Free-Operant (FO) preference assessment procedure [Roane, H. S., Vollmer, T. R., Ringdahl, J. E., & Marcus, B. A. (1998). Evaluation of a brief stimulus preference assessment. Journal of Applied Behavior Analysis, 31, 605-620] were conducted with four participants. A reinforcer assessment was conducted to determine which preference assessment procedure identified the item that produced the highest rates of responding. The items identified as most highly preferred were different across preference assessment procedures for all participants. Results of the reinforcer assessment showed that the MSW identified the item that functioned as the most effective reinforcer for two participants.

Subminiature eddy current transducers for studying metal- dielectric junctions

NASA Astrophysics Data System (ADS)

Dmitriev, S.; Katasonov, A.; Malikov, V.; Sagalakov, A.; Davydchenko, M.; Shevtsova, L.; Ishkov, A.

2016-11-01

Based on an eddy current transducer (ECT), a probe has been designed to research metal-dielectric structures. The measurement procedure allowing one to detect defects in laminate composites with a high accuracy is described. The transducer was tested on the layered structure consisting of paper and aluminum layers with a thickness of 100 μm each in which the model defect was placed. The dependences of the ECT signal on the defect in this structure are given.

Fiber optic tracheal detection device

NASA Astrophysics Data System (ADS)

Souhan, Brian E.; Nawn, Corinne D.; Shmel, Richard; Watts, Krista L.; Ingold, Kirk A.

2017-02-01

Poorly performed airway management procedures can lead to a wide variety of adverse events, such as laryngeal trauma, stenosis, cardiac arrest, hypoxemia, or death as in the case of failed airway management or intubation of the esophagus. Current methods for confirming tracheal placement, such as auscultation, direct visualization or capnography, may be subjective, compromised due to clinical presentation or require additional specialized equipment that is not always readily available during the procedure. Consequently, there exists a need for a non-visual detection mechanism for confirming successful airway placement that can give the provider rapid feedback during the procedure. Based upon our previously presented work characterizing the reflectance spectra of tracheal and esophageal tissue, we developed a fiber-optic prototype to detect the unique spectral characteristics of tracheal tissue. Device performance was tested by its ability to differentiate ex vivo samples of tracheal and esophageal tissue. Pig tissue samples were tested with the larynx, trachea and esophagus intact as well as excised and mounted on cork. The device positively detected tracheal tissue 18 out of 19 trials and 1 false positive out of 19 esophageal trials. Our proof of concept device shows great promise as a potential mechanism for rapid user feedback during airway management procedures to confirm tracheal placement. Ongoing studies will investigate device optimizations of the probe for more refined sensing and in vivo testing.

Final Report on Jobin Yvon Contained Inductively Coupled Plasma Emission Spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pennebaker, F.M.

2003-03-17

A new Inductively Coupled Plasma -- Emission Spectrometer (ICP-ES) was recently purchased and installed in Lab B-147/151 at SRTC. The contained JY Model Ultima 170-C ICP-ES has been tested and compared to current ADS ICP-ES instrumentation. The testing has included both performance tests to evaluate instrumental ability, and the measurement of matrix standards commonly analyzed by ICP-ES at Savannah River. In developing operating procedures for this instrument, we have implemented the use of internal standards and off-peak background subtraction. Both of these techniques are recommended by EPA SW-846 ICP-ES methods and are common to current ICP-ES operations. Based on themore » testing and changes, the JY Model Ultima 170-C ICP-ES provides improved performance for elemental analysis of radioactive samples in the Analytical Development Section.« less

Neurophysiological changes associated with implant-associated augmentation procedures in the lower jaw.

PubMed

Hartmann, Amely; Welte-Jzyk, Claudia; Seiler, Marcus; Daubländer, Monika

2017-08-01

Neurophysiological changes after oral and maxillofacial surgery remain one of the topics of current research. This study evaluated if implant placement associated with augmentation procedures increases the possibility of sensory disturbances or result in impaired quality of life during the healing period. Patients who had obtained an implant placement in the lower jaw in combination with augmentation procedures were examined by implementing a comprehensive Quantitative Sensory Testing (QST) protocol for extra- and intraoral use. As augmentation procedures, we used Guided Bone Regeneration (Group A) and Customized Bone Regeneration (Group B) techniques. Patients were tested bilaterally at the chin and mucosal lower lip. Results were compared to a group without augmentation procedures (Group C). Patients' quality of life and psychological comorbidity after the surgical procedures was assessed with the Oral Health Impact Profile and the Hospital Anxiety and Depression Scale. For groups A (n = 20) and B (n = 8), mechanical QST parameters showed no significant differences in all qualities of the inferior alveolar nerve compared to the contralateral side and compared to the nonaugmentation control group (n = 32) as well. Evaluation of quality of life and psychological factors showed no statistical differences. Augmentation procedures did not increase sensory disturbances, indicating no changes in the neurophysiological pathways. Extended augmentation procedures did not lead to sensory changes either or result in an impaired quality of life or modified anxiety and depression scores. © 2017 Wiley Periodicals, Inc.

Application of a Novel DCPD Adjustment Method for the J-R Curve Characterization: A study based on ORNL and ASTM Interlaboratory Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiang; Sokolov, Mikhail A; Nanstad, Randy K

Material fracture toughness in the fully ductile region can be described by a J-integral vs. crack growth resistance curve (J-R curve). As a conventional J-R curve measurement method, the elastic unloading compliance (EUC) method becomes impractical for elevated temperature testing due to relaxation of the material and friction induced back-up shape of the J-R curve. One alternative solution of J-R curve testing applies the Direct Current Potential Drop (DCPD) technique for measuring crack extension. However, besides crack growth, potential drop can also be influenced by plastic deformation, crack tip blunting, etc., and uncertainties exist in the current DCPD methodology especiallymore » in differentiating potential drop due to stable crack growth and due to material deformation. Thus, using DCPD for J-R curve determination remains a challenging task. In this study, a new adjustment procedure for applying DCPD to derive the J-R curve has been developed for conventional fracture toughness specimens, including compact tension, three-point bend, and disk-shaped compact specimens. Data analysis has been performed on Oak Ridge National Laboratory (ORNL) and American Society for Testing and Materials (ASTM) interlaboratory results covering different specimen thicknesses, test temperatures, and materials, to evaluate the applicability of the new DCPD adjustment procedure for J-R curve characterization. After applying the newly-developed procedure, direct comparison between the DCPD method and the normalization method on the same specimens indicated close agreement for the overall J-R curves, as well as the provisional values of fracture toughness near the onset of ductile crack extension, Jq, and of tearing modulus.« less

In Vitro, In Vivo and Post Explantation Testing of Glucose-Detecting Biosensors: Current Methods and Recommendations

PubMed Central

Koschwanez, Heidi E.; Reichert, W. Monty

2007-01-01

To date, there have been a number of cases where glucose sensors have performed well over long periods of implantation; however, it remains difficult to predict whether a given sensor will perform reliably, will exhibit gradual degradation of performance, or will fail outright soon after implantation. Typically, the literature emphasizes the sensor that performed well, while only briefly (if at all) mentioning the failed devices. This leaves open the question of whether current sensor designs are adequate for the hostile in vivo environment, and whether these sensors have been assessed by the proper regimen of testing protocols. This paper reviews the current in vitro and in vivo testing procedures used to evaluate the functionality and biocompatibility of implantable glucose sensors. An overview of the standards and regulatory bodies that govern biomaterials and end-product device testing precedes a discussion of up-to-date invasive and non-invasive technologies for diabetes management. Analysis of current in vitro, in vivo, and then post implantation testing is presented. Given the underlying assumption that the success of the sensor in vivo foreshadows the long-term reliability of the sensor in the human body, the relative merits of these testing methods are evaluated with respect to how representative they are of human models. PMID:17524479

The presence-absence coliform test for monitoring drinking water quality.

PubMed Central

Rice, E W; Geldreich, E E; Read, E J

1989-01-01

The concern for improved monitoring of the sanitary quality of drinking water has prompted interest in alternative methods for the detection of total coliform bacteria. A simplified qualitative presence-absence test has been proposed as an alternate procedure for detecting coliform bacteria in potable water. In this paper data from four comparative studies were analyzed to compare the recovery of total coliform bacteria from drinking water using the presence-absence test, the multiple fermentation tube procedure, and the membrane filter technique. The four studies were of water samples taken from four different geographic areas of the United States: Hawaii, New England (Vermont and New Hampshire), Oregon, and Pennsylvania. Analysis of the results of these studies were compared, based upon the number of positive samples detected by each method. Combined recoveries showed the presence-absence test detected significantly higher numbers of samples with coliforms than either the fermentation tube or membrane filter methods, P less than 0.01. The fermentation tube procedure detected significantly more positive samples than the membrane filter technique, P less than 0.01. Based upon the analysis of the combined data base, it is clear that the presence-absence test is as sensitive as the current coliform methods for the examination of potable water. The presence-absence test offers a viable alternative to water utility companies that elect to use the frequency-of-occurrence approach for compliance monitoring. PMID:2493663

Evaluating rodent motor functions: Which tests to choose?

PubMed

Schönfeld, Lisa-Maria; Dooley, Dearbhaile; Jahanshahi, Ali; Temel, Yasin; Hendrix, Sven

2017-12-01

Damage to the motor cortex induced by stroke or traumatic brain injury (TBI) can result in chronic motor deficits. For the development and improvement of therapies, animal models which possess symptoms comparable to the clinical population are used. However, the use of experimental animals raises valid ethical and methodological concerns. To decrease discomfort by experimental procedures and to increase the quality of results, non-invasive and sensitive rodent motor tests are needed. A broad variety of rodent motor tests are available to determine deficits after stroke or TBI. The current review describes and evaluates motor tests that fall into three categories: Tests to evaluate fine motor skills and grip strength, tests for gait and inter-limb coordination and neurological deficit scores. In this review, we share our thoughts on standardized data presentation to increase data comparability between studies. We also critically evaluate current methods and provide recommendations for choosing the best behavioral test for a new research line. Copyright © 2017 Elsevier Ltd. All rights reserved.

Investigation of electroforming techniques. [fabrication of regeneratively cooled thrust chambers

NASA Technical Reports Server (NTRS)

Malone, G. A.

1975-01-01

Copper and nickel electroforming was examined for the purpose of establishing the necessary processes and procedures for repeatable, successful fabrication of the outer structures of regeneratively cooled thrust chambers. The selection of electrolytes for copper and nickel deposition is described. The development studies performed to refine and complete the processes necessary for successful chamber shell fabrication and the testing employed to verify the applicability of the processes and procedures to small scale hardware are described. Specifications were developed to afford a guideline for the electroforming of high quality outer shells on regeneratively cooled thrust chamber liners. Test results indicated repeatable mechanical properties could be produced in copper deposits from the copper sulfate electrolyte with periodic current reversal and in nickel deposits from the sulfamate solution. Use of inert, removable channel fillers and the conductivizing of such is described. Techniques (verified by test) which produce high integrity bonds to copper and copper alloy liners are discussed.

Development of the Global Measles Laboratory Network.

PubMed

Featherstone, David; Brown, David; Sanders, Ray

2003-05-15

The routine reporting of suspected measles cases and laboratory testing of samples from these cases is the backbone of measles surveillance. The Global Measles Laboratory Network (GMLN) has developed standards for laboratory confirmation of measles and provides training resources for staff of network laboratories, reference materials and expertise for the development and quality control of testing procedures, and accurate information for the Measles Mortality Reduction and Regional Elimination Initiative. The GMLN was developed along the lines of the successful Global Polio Laboratory Network, and much of the polio laboratory infrastructure was utilized for measles. The GMLN has developed as countries focus on measles control activities following successful eradication of polio. Currently more than 100 laboratories are part of the global network and follow standardized testing and reporting procedures. A comprehensive laboratory accreditation process will be introduced in 2002 with six quality assurance and performance indicators.

Development of toughened epoxy polymers for high performance composite and ablative applications

NASA Technical Reports Server (NTRS)

Allen, V. R.

1982-01-01

A survey of current procedures for the assessment of state of cure in epoxy polymers and for the evaluation of polymer toughness as related to nature of the crosslinking agent was made to facilitate a cause-effect study of the chemical modification of epoxy polymers. Various conformations of sample morphology were examined to identify testing variables and to establish optimum conditions for the selected physical test methods. Dynamic viscoelasticity testing was examined in conjunction with chemical analyses to allow observation of the extent of the curing reaction with size of the crosslinking agent the primary variable. Specifically the aims of the project were twofold: (1) to consider the experimental variables associated with development of "extent of cure" analysis, and (2) to assess methodology of fracture energy determination and to prescribe a meaningful and reproducible procedure. The following is separated into two categories for ease of presentation.

Cross-Domain Analogies as Relating Derived Relations among Two Separate Relational Networks

PubMed Central

Ruiz, Francisco J; Luciano, Carmen

2011-01-01

Contemporary behavior analytic research is making headway in analyzing analogy as the establishment of a relation of coordination among common types of trained or derived relations. Previous studies have been focused on within-domain analogy. The current study expands previous research by analyzing cross-domain analogy as relating relations among separate relational networks and by correlating participants' performance with a standard measure of analogical reasoning. In two experiments, adult participants first completed general intelligence and analogical reasoning tests. Subsequently, they were exposed to a computerized conditional discrimination training procedure designed to create two relational networks, each consisting of two 3-member equivalence classes. The critical test was a two-part analogical test in which participants had to relate combinatorial relations of coordination and distinction between the two relational networks. In Experiment 1, combinatorial relations for each network were individually tested prior to analogical testing, but in Experiment 2 they were not. Across both experiments, 65% of participants passed the analogical test on the first attempt. Moreover, results from the training procedure were strongly correlated with the standard measure of analogical reasoning. PMID:21547072

Current Knowledge on Cannabinoids in Oral Fluid

PubMed Central

Lee, Dayong; Huestis, Marilyn A.

2015-01-01

Oral fluid (OF) is a new biological matrix for clinical and forensic drug testing, offering non-invasive and directly observable sample collection reducing adulteration potential, ease of multiple sample collections, lower biohazard risk during collection, recent exposure identification, and stronger correlation with blood than urine concentrations. Because cannabinoids are usually the most prevalent analytes in illicit drug testing, application of OF drug testing requires sufficient scientific data to support sensitive and specific OF cannabinoid detection. This review presents current knowledge on OF cannabinoids, evaluating pharmacokinetic properties, detection windows, and correlation with other biological matrices and impairment from field applications and controlled drug administration studies. In addition, on-site screening technologies, confirmatory analytical methods, drug stability, and effects of sample collection procedure, adulterants, and passive environmental exposure are reviewed. Delta-9-tetrahydrocannabinol OF concentrations could be > 1000 μg/L shortly after smoking, whereas minor cannabinoids are detected at 10-fold and metabolites at 1000-fold lower concentrations. OF research over the past decade demonstrated that appropriate interpretation of test results requires a comprehensive understanding of distinct elimination profiles and detection windows for different cannabinoids, which are influenced by administration route, dose, and drug use history. Thus, each drug testing program should establish cutoff criteria, collection/analysis procedures, and storage conditions tailored to its purposes. Building a scientific basis for OF testing is on-going, with continuing OF cannabinoids research on passive environmental exposure, drug use history, donor physiological conditions, and oral cavity metabolism needed to better understand mechanisms of cannabinoid OF disposition and expand OF drug testing applicability. PMID:23983217

Artificial intelligence and expert systems in-flight software testing

NASA Technical Reports Server (NTRS)

Demasie, M. P.; Muratore, J. F.

1991-01-01

The authors discuss the introduction of advanced information systems technologies such as artificial intelligence, expert systems, and advanced human-computer interfaces directly into Space Shuttle software engineering. The reconfiguration automation project (RAP) was initiated to coordinate this move towards 1990s software technology. The idea behind RAP is to automate several phases of the flight software testing procedure and to introduce AI and ES into space shuttle flight software testing. In the first phase of RAP, conventional tools to automate regression testing have already been developed or acquired. There are currently three tools in use.

Modification to the AOAC Sporicidal Activity of Disinfectants Test (Method 966.04): collaborative study.

PubMed

Tomasino, Stephen F; Hamilton, Martin A

2006-01-01

In an effort to improve AOAC Method 966.04, the Sporicidal Activity of Disinfectants Test, selected modifications to the procedure were evaluated in a collaborative study. Method 966.04 is used to generate efficacy data to support the product registration of sporicides and sterilants. The method is a carrier-based test that provides a qualitative measure of product efficacy against spores of Bacillus subtilis and Clostridium sporogenes. The use of garden soil extract and the lack of standard procedures for the enumeration of spores and neutralization of the test chemicals have been considered problematic for many years. The proposed modifications were limited to the B. subtilis and hard surface carrier (porcelain penicylinder) components of the method. The study included the evaluation of a replacement for soil extract nutrient broth and an establishment of a minimum spore titer per carrier, both considered crucial for the improvement and utilization of the method. Additionally, an alternative hard surface material and a neutralization confirmation procedure were evaluated. To determine the equivalence of the proposed alternatives to the standard method, 3 medium/carrier combinations, (1) soil extract nutrient broth/porcelain carrier (current method), (2) nutrient agar amended with 5 microg/mL manganese sulfate/porcelain carrier, and (3) nutrient agar amended with 5 microg/mL manganese sulfate/stainless steel carrier were analyzed for carrier counts, HCI resistance, efficacy, quantitative efficacy, and spore wash-off. The test chemicals used in the study represent 3 chemical classes and are commercially available antimicrobial liquid products: sodium hypochlorite (bleach), glutaraldehyde, and a combination of peracetic acid and hydrogen peroxide. Four laboratories participated in the study. The results of the spore titer per carrier, HCI resistance, efficacy, and wash-off studies demonstrate that amended nutrient agar in conjunction with the porcelain is comparable to the current method, soil extract nutrient broth/porcelain. The nutrient agar method is simple, inexpensive, reproducible, and provides an ample supply of high quality spores. Due to the current use of porcelain carriers for testing C. sporogenes, it is advisable to retain the use of porcelain carriers until stainless steel can be evaluated as a replacement carrier material for Clostridium. The evaluation of stainless steel for Clostridium has been initiated by the Study Director. Study Director recommendations for First Action revisions are provided in a modified method.

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XV, UNDERSTANDING DC GENERATOR PRINCIPLES (PART II).

ERIC Educational Resources Information Center

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF MAINTENANCE PROCEDURES FOR DIRECT CURRENT GENERATORS USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE SPECIAL GENERATOR CIRCUITS, GENERATOR TESTING, AND GENERATOR POLARITY. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL PROGRAMED TRAINING FILM "DC GENERATORS II--GENERATOR…

78 FR 41265 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

... 750 employees. DOE surveyed the AHRI certification directories for furnaces and boilers, as well as... calculation computer program to account for the new equations. 78 FR 7681, 7690 (Feb. 4, 2013). In the NOPR... quotes obtained from computer programmers familiar with the AFUE calculation program that is currently...

An Extension of IRT-Based Equating to the Dichotomous Testlet Response Theory Model

ERIC Educational Resources Information Center

Tao, Wei; Cao, Yi

2016-01-01

Current procedures for equating number-correct scores using traditional item response theory (IRT) methods assume local independence. However, when tests are constructed using testlets, one concern is the violation of the local item independence assumption. The testlet response theory (TRT) model is one way to accommodate local item dependence.…

More Powerful Tests of Simple Interaction Contrasts in the Two-Way Factorial Design

ERIC Educational Resources Information Center

Hancock, Gregory R.; McNeish, Daniel M.

2017-01-01

For the two-way factorial design in analysis of variance, the current article explicates and compares three methods for controlling the Type I error rate for all possible simple interaction contrasts following a statistically significant interaction, including a proposed modification to the Bonferroni procedure that increases the power of…

Establishing Auditory-Tactile-Visual Equivalence Classes in Children with Autism and Developmental Delays

ERIC Educational Resources Information Center

Mullen, Stuart; Dixon, Mark R.; Belisle, Jordan; Stanley, Caleb

2017-01-01

The current study sought to evaluate the efficacy of a stimulus equivalence training procedure in establishing auditory-tactile-visual stimulus classes with 2 children with autism and developmental delays. Participants were exposed to vocal-tactile (A-B) and tactile-picture (B-C) conditional discrimination training and were tested for the…

NASA reliability preferred practices for design and test

NASA Technical Reports Server (NTRS)

1991-01-01

Given here is a manual that was produced to communicate within the aerospace community design practices that have contributed to NASA mission success. The information represents the best technical advice that NASA has to offer on reliability design and test practices. Topics covered include reliability practices, including design criteria, test procedures, and analytical techniques that have been applied to previous space flight programs; and reliability guidelines, including techniques currently applied to space flight projects, where sufficient information exists to certify that the technique will contribute to mission success.

Management Control Systems in Not-for-Profit Organizations: A Case Study.

DTIC Science & Technology

1982-12-01

UNCLASSIFIED F/G 5/1 NL mhmmhhhhhmhmmum IEIIEEIIIIIEEE EIIIIIIIIIIIIl Diiit 1.1_I220 H- M141116 MICROCOPY RESOLUION4 TEST CHART 14ATIONAL BUREAU Of... test case. C. RESEARCH RET HODS The first phase of the study was a review of current literature on management control procedures and systems in...RESOLUTION TEST CHART NATIONAL BUREAU 0f SIANDARD 96% A I II a U a .1 ii IiU- I! IA i -~ - U I -..................... I I ~ 3 ,’u!nAA~~ -~~j ~; Eu ~ II 8I~ ~B

WE-A-210-00: Educational: Diagnostic Ultrasound QA

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This presentation will focus on the present role of ultrasound medical physics in clinical practices. The first part of the presentation will provide an overview of ultrasound QC methodologies and testing procedures. A brief review of ultrasound phantoms utilized in these testing procedures will be presented. The second part of the presentation will summarize ultrasound imaging technical standards and professional guidelines by American College of Radiology (ACR), American Institute of Ultrasound in Medicine (AIUM), American Association of Physicists in Medicine (AAPM) and International Electrotechnical Commission (IEC). The current accreditation requirements by ACR and AIUM for ultrasound practices will be describedmore » and the practical aspects of implementing QC programs to be compliant with these requirements will be discussed. Learning Objectives: Achieve familiarity with common ultrasound QC test methods and ultrasound phantoms. Understand the coverage of the existing testing standards and professional guidelines on diagnostic ultrasound imaging. Learn what a medical physicist needs to know about ultrasound program accreditation and be able to implement ultrasound QC programs accordingly.« less

Recent developments in nickel electrode analysis

NASA Technical Reports Server (NTRS)

Whiteley, Richard V.; Daman, M. E.; Kaiser, E. Q.

1991-01-01

Three aspects of nickel electrode analysis for Nickel-Hydrogen and Nickel-Cadmium battery cell applications are addressed: (1) the determination of active material; (2) charged state nickel (as NiOOH + CoOOH); and (3) potassium ion content in the electrode. Four deloading procedures are compared for completeness of active material removal, and deloading conditions for efficient active material analyses are established. Two methods for charged state nickel analysis are compared: the current NASA procedure and a new procedure based on the oxidation of sodium oxalate by the charged material. Finally, a method for determining potassium content in an electrode sample by flame photometry is presented along with analytical results illustrating differences in potassium levels from vendor to vendor and the effects of stress testing on potassium content in the electrode. The relevance of these analytical procedures to electrode performance is reviewed.

Finite element design procedure for correcting the coining die profiles

NASA Astrophysics Data System (ADS)

Alexandrino, Paulo; Leitão, Paulo J.; Alves, Luis M.; Martins, Paulo A. F.

2018-05-01

This paper presents a new finite element based design procedure for correcting the coining die profiles in order to optimize the distribution of pressure and the alignment of the resultant vertical force at the end of the die stroke. The procedure avoids time consuming and costly try-outs, does not interfere with the creative process of the sculptors and extends the service life of the coining dies by significantly decreasing the applied pressure and bending moments. The numerical simulations were carried out in a computer program based on the finite element flow formulation that is currently being developed by the authors in collaboration with the Portuguese Mint. A new experimental procedure based on the stack compression test is also proposed for determining the stress-strain curve of the materials directly from the coin blanks.

An IMU-to-Body Alignment Method Applied to Human Gait Analysis.

PubMed

Vargas-Valencia, Laura Susana; Elias, Arlindo; Rocon, Eduardo; Bastos-Filho, Teodiano; Frizera, Anselmo

2016-12-10

This paper presents a novel calibration procedure as a simple, yet powerful, method to place and align inertial sensors with body segments. The calibration can be easily replicated without the need of any additional tools. The proposed method is validated in three different applications: a computer mathematical simulation; a simplified joint composed of two semi-spheres interconnected by a universal goniometer; and a real gait test with five able-bodied subjects. Simulation results demonstrate that, after the calibration method is applied, the joint angles are correctly measured independently of previous sensor placement on the joint, thus validating the proposed procedure. In the cases of a simplified joint and a real gait test with human volunteers, the method also performs correctly, although secondary plane errors appear when compared with the simulation results. We believe that such errors are caused by limitations of the current inertial measurement unit (IMU) technology and fusion algorithms. In conclusion, the presented calibration procedure is an interesting option to solve the alignment problem when using IMUs for gait analysis.

Experimental new automatic tools for robotic stereotactic neurosurgery: towards "no hands" procedure of leads implantation into a brain target.

PubMed

Mazzone, P; Arena, P; Cantelli, L; Spampinato, G; Sposato, S; Cozzolino, S; Demarinis, P; Muscato, G

2016-07-01

The use of robotics in neurosurgery and, particularly, in stereotactic neurosurgery, is becoming more and more adopted because of the great advantages that it offers. Robotic manipulators easily allow to achieve great precision, reliability, and rapidity in the positioning of surgical instruments or devices in the brain. The aim of this work was to experimentally verify a fully automatic "no hands" surgical procedure. The integration of neuroimaging to data for planning the surgery, followed by application of new specific surgical tools, permitted the realization of a fully automated robotic implantation of leads in brain targets. An anthropomorphic commercial manipulator was utilized. In a preliminary phase, a software to plan surgery was developed, and the surgical tools were tested first during a simulation and then on a skull mock-up. In such a way, several tools were developed and tested, and the basis for an innovative surgical procedure arose. The final experimentation was carried out on anesthetized "large white" pigs. The determination of stereotactic parameters for the correct planning to reach the intended target was performed with the same technique currently employed in human stereotactic neurosurgery, and the robotic system revealed to be reliable and precise in reaching the target. The results of this work strengthen the possibility that a neurosurgeon may be substituted by a machine, and may represent the beginning of a new approach in the current clinical practice. Moreover, this possibility may have a great impact not only on stereotactic functional procedures but also on the entire domain of neurosurgery.

Customer Communication Document

NASA Technical Reports Server (NTRS)

2009-01-01

This procedure communicates to the Customers of the Automation, Robotics and Simulation Division (AR&SD) Dynamics Systems Test Branch (DSTB) how to obtain services of the Six-Degrees-Of-Freedom Dynamic Test System (SDTS). The scope includes the major communication documents between the SDTS and its Customer. It established the initial communication and contact points as well as provides the initial documentation in electronic media for the customer. Contact the SDTS Manager (SM) for the names of numbers of the current contact points.

Performance of Children With Developmental Dyslexia on Two Skill Learning Tasks-Serial Reaction Time and Tower of Hanoi Puzzle: A Test of the Specific Procedural Learning Difficulties Theory.

PubMed

Vakil, Eli; Lowe, Michal; Goldfus, Carol

2015-01-01

Among the various theories proposed to explain developmental dyslexia (DD), the theory of specific procedural learning difficulties has gained certain support and is the framework for the current research. This theory claims that an inability to achieve skill automaticity explains the difficulties experienced by individuals with DD. Previous research on automaticity and DD has exhibited methodological issues such as a failure to test a range of skills. The current study broadens previous findings by delineating various reading skills correlated with several aspects of skill acquisition. Furthermore, the study utilizes two nonverbal tasks that reflect distinct types of skills: Serial Reaction Time (SRT) and the Tower of Hanoi Puzzle (TOHP). A total of 53 children aged 11 to 13 participated in the study, of whom 23 were children with DD and 30 were controls. Participants completed a test battery that consisted of reading tests, the SRT, and the TOHP. Results show no differences in learning rate between individuals with or without DD, although individuals with DD performed both tasks at a slower rate. Correlations were identified between a number of reading measures and measures of skill acquisition, expressed primarily in individuals with DD. Implications are examined in the discussion. © Hammill Institute on Disabilities 2013.

Development of an in vitro Assay, Based on the BioFilm Ring Test®, for Rapid Profiling of Biofilm-Growing Bacteria

PubMed Central

Di Domenico, Enea G.; Toma, Luigi; Provot, Christian; Ascenzioni, Fiorentina; Sperduti, Isabella; Prignano, Grazia; Gallo, Maria T.; Pimpinelli, Fulvia; Bordignon, Valentina; Bernardi, Thierry; Ensoli, Fabrizio

2016-01-01

Microbial biofilm represents a major virulence factor associated with chronic and recurrent infections. Pathogenic bacteria embedded in biofilms are highly resistant to environmental and chemical agents, including antibiotics and therefore difficult to eradicate. Thus, reliable tests to assess biofilm formation by bacterial strains as well as the impact of chemicals or antibiotics on biofilm formation represent desirable tools for a most effective therapeutic management and microbiological risk control. Current methods to evaluate biofilm formation are usually time-consuming, costly, and hardly applicable in the clinical setting. The aim of the present study was to develop and assess a simple and reliable in vitro procedure for the characterization of biofilm-producing bacterial strains for future clinical applications based on the BioFilm Ring Test® (BRT) technology. The procedure developed for clinical testing (cBRT) can provide an accurate and timely (5 h) measurement of biofilm formation for the most common pathogenic bacteria seen in clinical practice. The results gathered by the cBRT assay were in agreement with the traditional crystal violet (CV) staining test, according to the κ coefficient test (κ = 0.623). However, the cBRT assay showed higher levels of specificity (92.2%) and accuracy (88.1%) as compared to CV. The results indicate that this procedure offers an easy, rapid and robust assay to test microbial biofilm and a promising tool for clinical microbiology. PMID:27708625

Assessment practices of professionals serving students who are deaf or hard of hearing: an initial investigation.

PubMed

Luckner, John L; Bowen, Sandy

2006-01-01

Assessment currently plays a critical role in American schools and society, in tasks ranging from ranking schools' effectiveness, to determining individual placement, to planning instruction. The purpose of the study was to gather data about the formal and informal assessment instruments and processes used by professionals in deaf education. Respondents indicated that statewide annual assessments are the most frequently used measures, followed by the Stanford Achievement Test series and the Woodcock-Johnson III Test of Achievement. Commonly used assessment instruments and procedures for each academic area are reported in rank order. Issues about current practices are raised, and suggestions for additional research related to assessment practices in deaf education are provided.

Diagnostic procedures for non-small-cell lung cancer (NSCLC): recommendations of the European Expert Group

PubMed Central

Dietel, Manfred; Bubendorf, Lukas; Dingemans, Anne-Marie C; Dooms, Christophe; Elmberger, Göran; García, Rosa Calero; Kerr, Keith M; Lim, Eric; López-Ríos, Fernando; Thunnissen, Erik; Van Schil, Paul E; von Laffert, Maximilian

2016-01-01

Background There is currently no Europe-wide consensus on the appropriate preanalytical measures and workflow to optimise procedures for tissue-based molecular testing of non-small-cell lung cancer (NSCLC). To address this, a group of lung cancer experts (see list of authors) convened to discuss and propose standard operating procedures (SOPs) for NSCLC. Methods Based on earlier meetings and scientific expertise on lung cancer, a multidisciplinary group meeting was aligned. The aim was to include all relevant aspects concerning NSCLC diagnosis. After careful consideration, the following topics were selected and each was reviewed by the experts: surgical resection and sampling; biopsy procedures for analysis; preanalytical and other variables affecting quality of tissue; tissue conservation; testing procedures for epidermal growth factor receptor, anaplastic lymphoma kinase and ROS proto-oncogene 1, receptor tyrosine kinase (ROS1) in lung tissue and cytological specimens; as well as standardised reporting and quality control (QC). Finally, an optimal workflow was described. Results Suggested optimal procedures and workflows are discussed in detail. The broad consensus was that the complex workflow presented can only be executed effectively by an interdisciplinary approach using a well-trained team. Conclusions To optimise diagnosis and treatment of patients with NSCLC, it is essential to establish SOPs that are adaptable to the local situation. In addition, a continuous QC system and a local multidisciplinary tumour-type-oriented board are essential. PMID:26530085

40 CFR 600.111-80 - Test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Test procedures. 600.111-80 Section... Model Year Automobiles-Test Procedures § 600.111-80 Test procedures. (a) The test procedures to be...-78 of this chapter, as applicable. (The evaporative and refueling loss portions of the test procedure...

40 CFR 600.111-93 - Test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Test procedures. 600.111-93 Section... Model Year Automobiles-Test Procedures § 600.111-93 Test procedures. (a) The test procedures to be... loss portion of the test procedure may be omitted unless specifically required by the Administrator...

A novel gel based vehicle for the delivery of acetylcholine in quantitative sudomotor axon reflex testing.

PubMed

Sletten, David M; Kimpinski, Kurt; Weigand, Stephen D; Low, Phillip A

2009-10-05

This study describes a novel gel based vehicle for the delivery of acetylcholine (ACh) during quantitative sudomotor axon reflex testing (QSART). A dose and current response study were undertaken on 20 healthy control participants to characterize the efficiency of a gel based vehicle for the delivery of ACh. Values obtained for total sweat volume and latency to sweat onset with gel iontophoresis of ACh during QSART were comparable to previously published normative data using solution based vehicles. Patient discomfort, utilizing the gel based vehicle during the QSART procedure, was minimal. Improvement in iontophoresis using the gel formulation as a vehicle for ACh delivery has the potential to lower the voltage required to overcome skin resistance during QSART and may result in improved patient comfort during the procedure.

"Turn laterally to the left!". The need for uniform C-arm communication terminology during orthopaedic trauma surgery.

PubMed

De Muinck Keizer, R-J; Klei, D S; Van Koperen, P J; Van Dijk, C N; Goslings, J C

2017-03-01

To avoid disturbed teamwork, unnecessary radiation exposure, and procedural delays, we designed and tested a uniform communication language for use in fluoroscopy-assisted surgical procedures. Input of surgeons and radiographers was used to create a set of commands. The potential benefit of this terminology was explored in an experimental setting. There was a tremendous diversity in the currently used terminology. Use of the newly designed terminology showed a reduction of procedural time and amount of images needed. Our first standardized Dutch language terminology can reduce total fluoroscopy time, number of images acquired, and potentially radiation exposure. For Dutch speaking colleagues, the developed terminology is freely available for use in their OR.

Current insights into the laboratory diagnosis of HIT.

PubMed

Bakchoul, T; Zöllner, H; Greinacher, A

2014-06-01

Heparin-induced thrombocytopenia (HIT) is an adverse drug reaction and prothrombotic disorder caused by immunization against platelet factor 4 (PF4) after complex formation with heparin or other polyanions. After antibody binding to PF4/heparin complexes, HIT antibodies are capable of intravascular platelet activation by cross-linking Fc gamma receptor IIa (FcγRIIa) on the platelet surface leading to a platelet count decrease and/or thrombosis. In contrast to most other immune-mediated disorders, the currently available laboratory tests for anti-PF4/heparin antibodies show a high sensitivity also for clinically irrelevant antibodies. This makes the diagnosis of HIT challenging and bears the risk to substantially overdiagnose HIT. The strength of the antigen assays for HIT is in ruling out HIT when the test is negative. Functional assays have a higher specificity for clinically relevant antibodies, but they are restricted to specialized laboratories. Currently, a Bayesian approach combining the clinical likelihood estimation for HIT with laboratory tests is the most appropriate approach to diagnose HIT. In this review, we give an overview on currently available diagnostic procedures and discuss their limitations. © 2014 John Wiley & Sons Ltd.

40 CFR 600.111-08 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Test procedures. 600.111-08 Section... Emission Test Procedures § 600.111-08 Test procedures. This section describes test procedures for the FTP, highway fuel economy test (HFET), US06, SC03, and the cold temperature FTP tests. Perform testing...

40 CFR 1033.315 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Test procedures. 1033.315 Section 1033... Programs § 1033.315 Test procedures. (a) Test procedures. Use the test procedures described in subpart F of this part, except as specified in this section. (1) You may ask to use other test procedures. We will...

40 CFR 1033.315 - Test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Test procedures. 1033.315 Section 1033... Programs § 1033.315 Test procedures. (a) Test procedures. Use the test procedures described in subpart F of this part, except as specified in this section. (1) You may ask to use other test procedures. We will...

40 CFR 1033.315 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Test procedures. 1033.315 Section 1033... Programs § 1033.315 Test procedures. (a) Test procedures. Use the test procedures described in subpart F of this part, except as specified in this section. (1) You may ask to use other test procedures. We will...

Uptake, outcomes, and costs of implementing non-invasive prenatal testing for Down’s syndrome into NHS maternity care: prospective cohort study in eight diverse maternity units

PubMed Central

Wright, David; Hill, Melissa; Verhoef, Talitha I; Daley, Rebecca; Lewis, Celine; Mason, Sarah; McKay, Fiona; Jenkins, Lucy; Howarth, Abigail; Cameron, Louise; McEwan, Alec; Fisher, Jane; Kroese, Mark; Morris, Stephen

2016-01-01

Objective To investigate the benefits and costs of implementing non-invasive prenatal testing (NIPT) for Down’s syndrome into the NHS maternity care pathway. Design Prospective cohort study. Setting Eight maternity units across the United Kingdom between 1 November 2013 and 28 February 2015. Participants All pregnant women with a current Down’s syndrome risk on screening of at least 1/1000. Main outcome measures Outcomes were uptake of NIPT, number of cases of Down’s syndrome detected, invasive tests performed, and miscarriages avoided. Pregnancy outcomes and costs associated with implementation of NIPT, compared with current screening, were determined using study data on NIPT uptake and invasive testing in combination with national datasets. Results NIPT was prospectively offered to 3175 pregnant women. In 934 women with a Down’s syndrome risk greater than 1/150, 695 (74.4%) chose NIPT, 166 (17.8%) chose invasive testing, and 73 (7.8%) declined further testing. Of 2241 women with risks between 1/151 and 1/1000, 1799 (80.3%) chose NIPT. Of 71 pregnancies with a confirmed diagnosis of Down’s syndrome, 13/42 (31%) with the diagnosis after NIPT and 2/29 (7%) after direct invasive testing continued, resulting in 12 live births. In an annual screening population of 698 500, offering NIPT as a contingent test to women with a Down’s syndrome screening risk of at least 1/150 would increase detection by 195 (95% uncertainty interval −34 to 480) cases with 3368 (2279 to 4027) fewer invasive tests and 17 (7 to 30) fewer procedure related miscarriages, for a non-significant difference in total costs (£−46 000, £−1 802 000 to £2 661 000). The marginal cost of NIPT testing strategies versus current screening is very sensitive to NIPT costs; at a screening threshold of 1/150, NIPT would be cheaper than current screening if it cost less than £256. Lowering the risk threshold increases the number of Down’s syndrome cases detected and overall costs, while maintaining the reduction in invasive tests and procedure related miscarriages. Conclusions Implementation of NIPT as a contingent test within a public sector Down’s syndrome screening programme can improve quality of care, choices for women, and overall performance within the current budget. As some women use NIPT for information only, the Down’s syndrome live birth rate may not change significantly. Future research should consider NIPT uptake and informed decision making outside of a research setting. PMID:27378786

Uptake, outcomes, and costs of implementing non-invasive prenatal testing for Down's syndrome into NHS maternity care: prospective cohort study in eight diverse maternity units.

PubMed

Chitty, Lyn S; Wright, David; Hill, Melissa; Verhoef, Talitha I; Daley, Rebecca; Lewis, Celine; Mason, Sarah; McKay, Fiona; Jenkins, Lucy; Howarth, Abigail; Cameron, Louise; McEwan, Alec; Fisher, Jane; Kroese, Mark; Morris, Stephen

2016-07-04

 To investigate the benefits and costs of implementing non-invasive prenatal testing (NIPT) for Down's syndrome into the NHS maternity care pathway.  Prospective cohort study.  Eight maternity units across the United Kingdom between 1 November 2013 and 28 February 2015.  All pregnant women with a current Down's syndrome risk on screening of at least 1/1000.  Outcomes were uptake of NIPT, number of cases of Down's syndrome detected, invasive tests performed, and miscarriages avoided. Pregnancy outcomes and costs associated with implementation of NIPT, compared with current screening, were determined using study data on NIPT uptake and invasive testing in combination with national datasets.  NIPT was prospectively offered to 3175 pregnant women. In 934 women with a Down's syndrome risk greater than 1/150, 695 (74.4%) chose NIPT, 166 (17.8%) chose invasive testing, and 73 (7.8%) declined further testing. Of 2241 women with risks between 1/151 and 1/1000, 1799 (80.3%) chose NIPT. Of 71 pregnancies with a confirmed diagnosis of Down's syndrome, 13/42 (31%) with the diagnosis after NIPT and 2/29 (7%) after direct invasive testing continued, resulting in 12 live births. In an annual screening population of 698 500, offering NIPT as a contingent test to women with a Down's syndrome screening risk of at least 1/150 would increase detection by 195 (95% uncertainty interval -34 to 480) cases with 3368 (2279 to 4027) fewer invasive tests and 17 (7 to 30) fewer procedure related miscarriages, for a non-significant difference in total costs (£-46 000, £-1 802 000 to £2 661 000). The marginal cost of NIPT testing strategies versus current screening is very sensitive to NIPT costs; at a screening threshold of 1/150, NIPT would be cheaper than current screening if it cost less than £256. Lowering the risk threshold increases the number of Down's syndrome cases detected and overall costs, while maintaining the reduction in invasive tests and procedure related miscarriages.  Implementation of NIPT as a contingent test within a public sector Down's syndrome screening programme can improve quality of care, choices for women, and overall performance within the current budget. As some women use NIPT for information only, the Down's syndrome live birth rate may not change significantly. Future research should consider NIPT uptake and informed decision making outside of a research setting. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The culture of time in neuropsychological assessment: exploring the effects of culture-specific time attitudes on timed test performance in Russian and American samples.

PubMed

Agranovich, Anna V; Panter, A T; Puente, Antonio E; Touradji, Pegah

2011-07-01

Cultural differences in time attitudes and their effect on timed neuropsychological test performance were examined in matched non-clinical samples of 100 Russian and American adult volunteers using 8 tests that were previously reported to be relatively free of cultural bias: Color Trails Test (CTT); Ruff Figural Fluency Test (RFFT); Symbol Digit Modalities Test (SDMT); and Tower of London-Drexel Edition (ToL(Dx)). A measure of time attitudes, the Culture of Time Inventory (COTI-33) was used to assess time attitudes potentially affecting time-limited testing. Americans significantly outscored Russians on CTT, SDMT, and ToL(Dx) (p,.05) while differences in RFFT scores only approached statistical significance. Group differences also emerged in COTI-33 factor scores, which partially mediated differences in performance on CTT-1, SDMT, and ToL(Dx) initiation time, but did not account for the effect of culture on CTT-2. Significant effect of culture was revealed in ratings of familiarity with testing procedures that was negatively related to CTT, ToL(Dx), and SDMT scores. Current findings indicated that attitudes toward time may influence results of time limited testing and suggested that individuals who lack familiarity with timed testing procedures tend to obtain lower scores on timed tests.

Estimating False Discovery Proportion Under Arbitrary Covariance Dependence*

PubMed Central

Fan, Jianqing; Han, Xu; Gu, Weijie

2012-01-01

Multiple hypothesis testing is a fundamental problem in high dimensional inference, with wide applications in many scientific fields. In genome-wide association studies, tens of thousands of tests are performed simultaneously to find if any SNPs are associated with some traits and those tests are correlated. When test statistics are correlated, false discovery control becomes very challenging under arbitrary dependence. In the current paper, we propose a novel method based on principal factor approximation, which successfully subtracts the common dependence and weakens significantly the correlation structure, to deal with an arbitrary dependence structure. We derive an approximate expression for false discovery proportion (FDP) in large scale multiple testing when a common threshold is used and provide a consistent estimate of realized FDP. This result has important applications in controlling FDR and FDP. Our estimate of realized FDP compares favorably with Efron (2007)’s approach, as demonstrated in the simulated examples. Our approach is further illustrated by some real data applications. We also propose a dependence-adjusted procedure, which is more powerful than the fixed threshold procedure. PMID:24729644

A review of the evidence for endocrine disrupting effects of current-use chemicals on wildlife populations.

PubMed

Matthiessen, Peter; Wheeler, James R; Weltje, Lennart

2018-03-01

This review critically examines the data on claimed endocrine-mediated adverse effects of chemicals on wildlife populations. It focuses on the effects of current-use chemicals, and compares their apparent scale and severity with those of legacy chemicals which have been withdrawn from sale or use, although they may still be present in the environment. The review concludes that the effects on wildlife of many legacy chemicals with endocrine activity are generally greater than those caused by current-use chemicals, with the exception of ethinylestradiol and other estrogens found in sewage effluents, which are causing widespread effects on fish populations. It is considered that current chemical testing regimes and risk assessment procedures, at least those to which pesticides and biocides are subjected, are in part responsible for this improvement. This is noteworthy as most ecotoxicological testing for regulatory purposes is currently focused on characterizing apical adverse effect endpoints rather than identifying the mechanism(s) responsible for any observed effects. Furthermore, a suite of internationally standardized ecotoxicity tests sensitive for potential endocrine-mediated effects is now in place, or under development, which should ensure further characterization of substances with these properties so that they can be adequately regulated.

Iterating between lessons on concepts and procedures can improve mathematics knowledge.

PubMed

Rittle-Johnson, Bethany; Koedinger, Kenneth

2009-09-01

Knowledge of concepts and procedures seems to develop in an iterative fashion, with increases in one type of knowledge leading to increases in the other type of knowledge. This suggests that iterating between lessons on concepts and procedures may improve learning. The purpose of the current study was to evaluate the instructional benefits of an iterative lesson sequence compared to a concepts-before-procedures sequence for students learning decimal place-value concepts and arithmetic procedures. In two classroom experiments, sixth-grade students from two schools participated (N=77 and 26). Students completed six decimal lessons on an intelligent-tutoring systems. In the iterative condition, lessons cycled between concept and procedure lessons. In the concepts-first condition, all concept lessons were presented before introducing the procedure lessons. In both experiments, students in the iterative condition gained more knowledge of arithmetic procedures, including ability to transfer the procedures to problems with novel features. Knowledge of concepts was fairly comparable across conditions. Finally, pre-test knowledge of one type predicted gains in knowledge of the other type across experiments. An iterative sequencing of lessons seems to facilitate learning and transfer, particularly of mathematical procedures. The findings support an iterative perspective for the development of knowledge of concepts and procedures.

Prevalidation of an Acute Inhalation Toxicity Test Using the EpiAirway In Vitro Human Airway Model

PubMed Central

Jackson, George R.; Maione, Anna G.; Klausner, Mitchell

2018-01-01

Abstract Introduction: Knowledge of acute inhalation toxicity potential is important for establishing safe use of chemicals and consumer products. Inhalation toxicity testing and classification procedures currently accepted within worldwide government regulatory systems rely primarily on tests conducted in animals. The goal of the current work was to develop and prevalidate a nonanimal (in vitro) test for determining acute inhalation toxicity using the EpiAirway™ in vitro human airway model as a potential alternative for currently accepted animal tests. Materials and Methods: The in vitro test method exposes EpiAirway tissues to test chemicals for 3 hours, followed by measurement of tissue viability as the test endpoint. Fifty-nine chemicals covering a broad range of toxicity classes, chemical structures, and physical properties were evaluated. The in vitro toxicity data were utilized to establish a prediction model to classify the chemicals into categories corresponding to the currently accepted Globally Harmonized System (GHS) and the Environmental Protection Agency (EPA) system. Results: The EpiAirway prediction model identified in vivo rat-based GHS Acute Inhalation Toxicity Category 1–2 and EPA Acute Inhalation Toxicity Category I–II chemicals with 100% sensitivity and specificity of 43.1% and 50.0%, for GHS and EPA acute inhalation toxicity systems, respectively. The sensitivity and specificity of the EpiAirway prediction model for identifying GHS specific target organ toxicity-single exposure (STOT-SE) Category 1 human toxicants were 75.0% and 56.5%, respectively. Corrosivity and electrophilic and oxidative reactivity appear to be the predominant mechanisms of toxicity for the most highly toxic chemicals. Conclusions: These results indicate that the EpiAirway test is a promising alternative to the currently accepted animal tests for acute inhalation toxicity. PMID:29904643

Prevalidation of an Acute Inhalation Toxicity Test Using the EpiAirway In Vitro Human Airway Model.

PubMed

Jackson, George R; Maione, Anna G; Klausner, Mitchell; Hayden, Patrick J

2018-06-01

Introduction: Knowledge of acute inhalation toxicity potential is important for establishing safe use of chemicals and consumer products. Inhalation toxicity testing and classification procedures currently accepted within worldwide government regulatory systems rely primarily on tests conducted in animals. The goal of the current work was to develop and prevalidate a nonanimal ( in vitro ) test for determining acute inhalation toxicity using the EpiAirway™ in vitro human airway model as a potential alternative for currently accepted animal tests. Materials and Methods: The in vitro test method exposes EpiAirway tissues to test chemicals for 3 hours, followed by measurement of tissue viability as the test endpoint. Fifty-nine chemicals covering a broad range of toxicity classes, chemical structures, and physical properties were evaluated. The in vitro toxicity data were utilized to establish a prediction model to classify the chemicals into categories corresponding to the currently accepted Globally Harmonized System (GHS) and the Environmental Protection Agency (EPA) system. Results: The EpiAirway prediction model identified in vivo rat-based GHS Acute Inhalation Toxicity Category 1-2 and EPA Acute Inhalation Toxicity Category I-II chemicals with 100% sensitivity and specificity of 43.1% and 50.0%, for GHS and EPA acute inhalation toxicity systems, respectively. The sensitivity and specificity of the EpiAirway prediction model for identifying GHS specific target organ toxicity-single exposure (STOT-SE) Category 1 human toxicants were 75.0% and 56.5%, respectively. Corrosivity and electrophilic and oxidative reactivity appear to be the predominant mechanisms of toxicity for the most highly toxic chemicals. Conclusions: These results indicate that the EpiAirway test is a promising alternative to the currently accepted animal tests for acute inhalation toxicity.

40 CFR 600.111-08 - Test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Test procedures. 600.111-08 Section... Emission Test Procedures § 600.111-08 Test procedures. This section provides test procedures for the FTP, highway, US06, SC03, and the cold temperature FTP tests. Testing shall be performed according to test...

Recollection and familiarity for words and faces: a study comparing Remember-Know judgements and the Process Dissociation Procedure.

PubMed

Espinosa-García, María; Vaquero, Joaquín M M; Milliken, Bruce; Tudela, Pío

2017-01-01

Measures of recollection and familiarity often differ depending on the paradigm utilised. Remember-Know (R-K) and Process Dissociation Procedure (PDP) methods have been commonly used but rarely compared within a single study. In the current experiments, R-K and PDP were compared by examining the effect of attention at study and time to respond at test on recollection and familiarity using the same experimental procedures for each paradigm. We also included faces in addition to words to test the generality of the findings often obtained using words. The results from the R-K paradigm revealed that recollection and familiarity were similarly affected by attention at study and time to respond at test. However, in the case of PDP, the measures of recollection and familiarity showed a different pattern of results. The effects observed for recollection were similar to those obtained with the R-K method, whereas familiarity was affected by time to respond but not by attention at study. These results are discussed in relation to the controlled-automatic processing distinction and the contribution of each paradigm to research on recognition memory.

Reliability analysis applied to structural tests

NASA Technical Reports Server (NTRS)

Diamond, P.; Payne, A. O.

1972-01-01

The application of reliability theory to predict, from structural fatigue test data, the risk of failure of a structure under service conditions because its load-carrying capability is progressively reduced by the extension of a fatigue crack, is considered. The procedure is applicable to both safe-life and fail-safe structures and, for a prescribed safety level, it will enable an inspection procedure to be planned or, if inspection is not feasible, it will evaluate the life to replacement. The theory has been further developed to cope with the case of structures with initial cracks, such as can occur in modern high-strength materials which are susceptible to the formation of small flaws during the production process. The method has been applied to a structure of high-strength steel and the results are compared with those obtained by the current life estimation procedures. This has shown that the conventional methods can be unconservative in certain cases, depending on the characteristics of the structure and the design operating conditions. The suitability of the probabilistic approach to the interpretation of the results from full-scale fatigue testing of aircraft structures is discussed and the assumptions involved are examined.

Development of an Accelerated Test Method for the Determination of Susceptibility to Atmospheric Corrosion

NASA Technical Reports Server (NTRS)

Ambrose, John R.

1991-01-01

The theoretical rationale is presented for use of a repetitive cyclic current reversal voltammetric technique for characterization of localized corrosion processes, including atmospheric corrosion. Applicability of this proposed experimental protocol is applied to characterization of susceptibility to crevice and pitting corrosion, atmospheric corrosion and stress corrosion cracking. Criteria upon which relative susceptibility is based were determined and tested using two iron based alloys commonly in use at NASA-Kennedy; A36 (a low carbon steel) and 4130 (a low alloy steel). Practicality of the procedure was demonstrated by measuring changes in anodic polarization behavior during high frequency current reversal cycles of 25 cycles per second with 1 mA/sq cm current density amplitude in solutions containing Cl anions. The results demonstrated that, due to excessive polarization which affects conductivity of barrier corrosion product layers, A36 was less resistant to atmospheric corrosion than its 4130 counterpart; behavior which was also demonstrated during exposure tests.

Mixed-Mode Bending Method for Delamination Testing

NASA Technical Reports Server (NTRS)

Reeder, James R.; Crews, John R., Jr.

1990-01-01

A mixed mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate. By loading with a lever, a single applied load simultaneously produces mode I and mode II bending loads on the specimen. This mixed-mode bending (MMB) test was analyzed using both finite-element procedures and beam theory to calculate the mode I and mode II components of strain-energy release rate G(sub I) and G(sub II), respectively. A wide range of G(sub I)/G(sub II) ratios can be produced by varying the load position on the lever. As the delamination extended, the G(sub I)/G(sub II) ratios varied by less than 5%. Beam theory equations agreed closely with the finite-element results and provide a basis for selection of G(sub I)/G(sub II) test ratios and a basis for computing the mode I and mode II components of measured delamination toughness. The MMB test was demonstrated using AS4/PEEK (APC2) unidirectional laminates. The MMB test introduced in this paper is rather simple and is believed to offer several advantages over most current mixed-mode test.

The Production of Polyclonal Antibodies in Laboratory Animals. The Report and Recommendations of ECVAM Workshop 35.

PubMed

Leenaars, P P; Hendriksen, C F; de Leeuw, W A; Carat, F; Delahaut, P; Fischer, R; Halder, M; Hanly, W C; Hartinger, J; Hau, J; Lindblad, E B; Nicklas, W; Outschoorn, I M; Stewart-Tull, D E

1999-01-01

This is the report of the thirty-fifth of a series of workshops organised by the European Centre for the Validation of Alternative Methods (ECVAM). ECVAM's main goal, as defined in 1993 by its Scientific Advisory Committee, is to promote the scientific and regulatory acceptance of alternative methods which are of importance to the biosciences and which reduce, refine or replace the use of laboratory animals. One of the first priorities set by ECVAM was the implementation of procedures which would enable it to become well informed about the state-of-the-art of non-animal test development and validation, and the potential for the possible incorporation of alternative tests into regulatory procedures. It was decided that this would be best achieved by the organisation of ECVAM workshops on specific topics, at which small groups of invited experts would review the current status of various types of in vitro tests and their potential uses, and make recommendations about the best ways forward (1). This joint ECVAM/FELASA (Federation of European Laboratory Animal Science Associations) workshop on The Immunisation of Laboratory Animals for the Production of Polyclonal Antibodies was held in Utrecht (The Netherlands), on 20-22 March 1998, under the co-chairmanship of Coenraad Hendriksen (RIVM, Bilthoven, The Netherlands) and Wim de Leeuw (Inspectorate for Health Protection, The Netherlands). The participants, all experts in the fields of immunology, laboratory animal science, or regulation, came from universities, industry and regulatory bodies. The aims of the workshop were: a) to discuss and evaluate current immunisation procedures for the production of polyclonal antibodies (including route of injection, animal species and adjuvant ); and b) to draft recommendations and guidelines to improve the immunisation procedures, with regard both to animal welfare and to the optimisation of immunisation protocols. This report summarises the outcome of the discussions and includes a number of recommendations and a set of draft guidelines (included in Appendix 1). 1999 FRAME.

WHO Expert Committee on Specifications for Pharmaceutical Preparations.

PubMed

2009-01-01

The Expert Committee on Specifications for Pharmaceutical Preparations works towards clear, independent and practical standards and guidelines for the quality assurance of medicines. Standards are developed by the Committee through worldwide consultation and an international consensus-building process. The following new standards and guidelines were adopted and recommended for use: the current list of available International Chemical Reference Substances and International Infrared Reference Spectra; guidelines on stability testing of active pharmaceutical ingredients and finished pharmaceutical products; procedure for prequalification of pharmaceutical products; and the procedure for assessing the acceptability, in principle, of active pharmaceutical ingredients for use in pharmaceutical products.

Communications processor for C3 analysis and wargaming

NASA Astrophysics Data System (ADS)

Clark, L. N.; Pless, L. D.; Rapp, R. L.

1982-03-01

This thesis developed the software capability to allow the investigation of c3 problems, procedures and methodologies. The resultant communications model, that while independent of a specific wargame, is currently implemented in conjunction with the McClintic Theater Model. It provides a computerized message handling system (C3 Model) which allows simulation of communication links (circuits) with user-definable delays; garble and loss rates; and multiple circuit types, addresses, and levels of command. It is designed to be used for test and evaluation of command and control problems in the areas of organizational relationships, communication networks and procedures, and combat doctrine or tactics.

40 CFR 600.111-08 - Test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Test procedures. 600.111-08 Section... Model Year Automobiles-Test Procedures § 600.111-08 Test procedures. This section provides test procedures for the FTP, highway, US06, SC03, and the cold temperature FTP tests. Testing shall be performed...

Testing coordinate measuring arms with a geometric feature-based gauge: in situ field trials

NASA Astrophysics Data System (ADS)

Cuesta, E.; Alvarez, B. J.; Patiño, H.; Telenti, A.; Barreiro, J.

2016-05-01

This work describes in detail the definition of a procedure for calibrating and evaluating coordinate measuring arms (AACMMs or CMAs). CMAs are portable coordinate measuring machines that have been widely accepted in industry despite their sensitivity to the skill and experience of the operator in charge of the inspection task. The procedure proposed here is based on the use of a dimensional gauge that incorporates multiple geometric features, specifically designed for evaluating the measuring technique when CMAs are used, at company facilities (workshops or laboratories) and by the usual operators who handle these devices in their daily work. After establishing the procedure and manufacturing the feature-based gauge, the research project was complemented with diverse in situ field tests performed with the collaboration of companies that use these devices in their inspection tasks. Some of the results are presented here, not only comparing different operators but also comparing different companies. The knowledge extracted from these experiments has allowed the procedure to be validated, the defects of the methodologies currently used for in situ inspections to be detected, and substantial improvements for increasing the reliability of these portable instruments to be proposed.

IL-6 does not predict current urolithiasis in stone formers.

PubMed

Rieder, Jocelyn M; Nisbet, Alan A; Lesser, Timothy; Franke, Ethan I; Brusky, John P; Parekh, Ashish R; Kaptein, John; Bellman, Gary C

2008-10-01

Interleukin-6 (IL-6), an inflammatory marker, has previously been found to be elevated in the urine of patients with urolithiasis. Oxalate and other stone precursors have been shown to increase IL-6 production in proximal tubular epithelial cells in vitro. We examined whether urinary IL-6 could be used as a screening test to determine current urolithiasis in individuals who are known to form urinary stones. Thirty-five adult patients with current urolithiasis demonstrated on imaging were enrolled in the study. Exclusion criteria included disease known to elevate IL-6. Each patient provided a pre-treatment urine specimen and one month after proven to be stone-free an additional urine specimen was obtained. The urinary IL-6/creatinine ratio was determined for both specimens and compared. Ten patients provided both specimens. The mean pre-operative urinary IL-6/creatinine ratio before the procedure was 1.63 pg/mL. The mean post procedure urinary IL-6/creatinine ratio after the patient was confirmed to be stone-free was 1.81 pg/mL. These were not significantly different (p=0.38). Preoperative urinary IL-6/creatinine ratio did not correlate to stone size (r=0.15) and no correlation was seen between time from treatment and stone free IL-6/creatinine ratio (r=0.48). Urinary IL-6 is not a good screening test for current urolithiasis in stone-forming individuals. It is elevated whether the stone is present or not.

Orion Ammonia Boiler System Preflight Test Preparations

NASA Technical Reports Server (NTRS)

Levitt, Julia L.

2017-01-01

The Environmental Controls and Life Support Systems (ECLSS) branch at Kennedy Space Center (KSC) is currently undergoing preparations for ground testing of the Orion Multi-Purpose Crew Vehicle (MPCV) to prepare its subsystems for EM-1 (Exploration Mission-1). EM-1, Orions second unmanned flight, is a three-week long lunar mission during which the vehicle will complete a 6-day retrograde lunar orbit before returning to Earth. This paper focuses on the work done during the authors 16-week internship with the Mechanical Engineering Branch of KSCs Engineering Directorate. The authors project involved assisting with the preparations for testing the Orion MPCVs ammonia boiler system. The purpose of the ammonia boiler system is to keep the spacecraft sufficiently cool during the reentry portion of its mission, from service module (SM) separation to post-landing. This system is critical for keeping both the spacecraft (avionics and electronics) and crew alive during reentry, thus a successful test of the system is essential to the success of EM-1. XXXX The author was able to draft a detailed outline of the procedure for the ammonia system functional test. More work will need to be done on the vehicle power-up and power-down portions of the procedure, but the ammonia system testing portion of the procedure is thorough and includes vehicle test configurations, vehicle commands, and GSE. The author was able to compile a substantial list of questions regarding the ammonia system functional test with the help of her mentors. A significant number of these questions were answered in the teleconferences with Lockheed Martin.

Noninvasive prenatal screening for fetal aneuploidy, 2016 update: a position statement of the American College of Medical Genetics and Genomics.

PubMed

Gregg, Anthony R; Skotko, Brian G; Benkendorf, Judith L; Monaghan, Kristin G; Bajaj, Komal; Best, Robert G; Klugman, Susan; Watson, Michael S

2016-10-01

This statement is designed primarily as an educational resource for clinicians to help them provide quality medical services. Adherence to this statement is completely voluntary and does not necessarily assure a successful medical outcome. This statement should not be considered inclusive of all proper procedures and tests or exclusive of other procedures and tests that are reasonably directed toward obtaining the same results. In determining the propriety of any specific procedure or test, the clinician should apply his or her own professional judgment to the specific clinical circumstances presented by the individual patient or specimen. Clinicians are encouraged to document the reasons for the use of a particular procedure or test, whether or not it is in conformance with this statement. Clinicians also are advised to take notice of the date this statement was adopted and to consider other medical and scientific information that becomes available after that date. It also would be prudent to consider whether intellectual property interests may restrict the performance of certain tests and other procedures.Noninvasive prenatal screening using cell-free DNA (NIPS) has been rapidly integrated into prenatal care since the initial American College of Medical Genetics and Genomics (ACMG) statement in 2013. New evidence strongly suggests that NIPS can replace conventional screening for Patau, Edwards, and Down syndromes across the maternal age spectrum, for a continuum of gestational age beginning at 9-10 weeks, and for patients who are not significantly obese. This statement sets forth a new framework for NIPS that is supported by information from validation and clinical utility studies. Pretest counseling for NIPS remains crucial; however, it needs to go beyond discussions of Patau, Edwards, and Down syndromes. The use of NIPS to include sex chromosome aneuploidy screening and screening for selected copy-number variants (CNVs) is becoming commonplace because there are no other screening options to identify these conditions. Providers should have a more thorough understanding of patient preferences and be able to educate about the current drawbacks of NIPS across the prenatal screening spectrum. Laboratories are encouraged to meet the needs of providers and their patients by delivering meaningful screening reports and to engage in education. With health-care-provider guidance, the patient should be able to make an educated decision about the current use of NIPS and the ramifications of a positive, negative, or no-call result.Genet Med 18 10, 1056-1065.

Digital enhancement of X-rays for NDT

NASA Technical Reports Server (NTRS)

Butterfield, R. L.

1980-01-01

Report is "cookbook" for digital processing of industrial X-rays. Computer techniques, previously used primarily in laboratory and developmental research, have been outlined and codified into step by step procedures for enhancing X-ray images. Those involved in nondestructive testing should find report valuable asset, particularly is visual inspection is method currently used to process X-ray images.

DETERMINING POTENTIAL RISK TO NATIVE PLANTS FROM HERBICIDE DRIFT: COMPARATIVE RESPONSE OF SELECTED CROP AND NATIVE PLANT SPECIES TO GLYPHOSATE AND SULFOMETURON

EPA Science Inventory

abstract/abstract

While native plant communities may be at risk from herbicide use, current crop-centric test procedures for pesticide registration may not adequately represent the sensitivity of native non-crop plants to herbicides. We are designing a protocol to determi...

Investigation Into The Effectiveness of The JLAB High Pressure Rinse System

DOE Office of Scientific and Technical Information (OSTI.GOV)

John Mammosser; Timothy Rothgeb; Tong Wang

2003-05-01

As part of a study to reduce field emission in Superconducting radio frequency cavities, an investigation into the effectiveness of the Jefferson Lab's High Pressure Rinse (HPR) system is underway. This paper describes discoveries from this investigation, the procedural changes made during this investigation, current vertical test results and further plans for improvements and monitoring.

Introduction to basic solar cell measurements

NASA Technical Reports Server (NTRS)

Brandhorst, H. W., Jr.

1976-01-01

The basic approaches to solar cell performance and diagnostic measurements are described. The light sources, equipment for I-V curve measurement, and the test conditions and procedures for performance measurement are detailed. Solar cell diagnostic tools discussed include analysis of I-V curves, series resistance and reverse saturation current determination, spectral response/quantum yield measurement, and diffusion length/lifetime determination.

Patch testing custom isocyanate materials from the workplace.

PubMed

Burrows, Dianne; Houle, Marie-Claude; Holness, D Linn; DeKoven, Joel; Skotnicki, Sandy

2015-01-01

Patch testing with standard trays of commercially available allergens is the current practice for investigating suspected cases of isocyanate-induced allergic contact dermatitis (ACD). In some facilities, these standard trays are further supplemented with custom preparations of isocyanate-containing materials. The aim was to determine whether added value exists in patch testing patients to custom isocyanate preparations in suspected cases of ACD. We performed a retrospective analysis of 11 patients referred to our specialty clinic between January 2003 and March 2011 for suspected patients of ACD who had custom testing with isocyanate materials from their workplace. In addition to standard trays of allergens, all patients were patch tested with custom isocyanate materials from their workplaces. Three (27%) of 11 patients showed an added value in testing to custom isocyanate allergens. Of these 3 patients, one had a reaction that reinforced positive reactions to the standard isocyanate tray, but the other 2 (18%) had no reactions to any of the commercially available allergens. Because of the high proportion of reactions (27%), we recommend the use of custom testing to workplace isocyanate products as a supplement to current standard patch testing procedures.

Wind tunnel wall interference

NASA Technical Reports Server (NTRS)

Newman, Perry A.; Mineck, Raymond E.; Barnwell, Richard W.; Kemp, William B., Jr.

1986-01-01

About a decade ago, interest in alleviating wind tunnel wall interference was renewed by advances in computational aerodynamics, concepts of adaptive test section walls, and plans for high Reynolds number transonic test facilities. Selection of NASA Langley cryogenic concept for the National Transonic Facility (NTF) tended to focus the renewed wall interference efforts. A brief overview and current status of some Langley sponsored transonic wind tunnel wall interference research are presented. Included are continuing efforts in basic wall flow studies, wall interference assessment/correction procedures, and adaptive wall technology.

Finding Platinum-Coating Gaps On Titanium Anodes

NASA Technical Reports Server (NTRS)

Bodemeijer, Ronnald; Flowers, Cecil E.

1990-01-01

Simple procedure makes gaps visible to eye. New gap-detection method consists of plating thin layer of non-silver-colored metal like copper or gold on anode. Contrast in color between plated metal and bare anode material makes gaps stand out. If anode passes inspection, copper or gold plate removable by reversal of test-plating current. Remains to be determined whether test plating and removal damages anode. New method simpler and more economical than previous attempts to identify gaps in platinum.

Analysis of remote sensing data for evaluating vegetation resources

NASA Technical Reports Server (NTRS)

1971-01-01

Increased utilization studies for current remote sensor and analysis capabilities included: (1) a review of testing procedures for quantifying the accuracy of photointerpretation; (2) field tests of a fully portable spectral data gathering system, both on the ground and from a helicopter; and (3) a comparison of three methods for obtaining ground information necessary for regional agricultural inventories. A version of the LARS point-by-point classification system was upgraded by the addition of routines to analyze spatial data information.

Future Combat System Spinout 1 Technical Field Test - Establishing and Implementing Models and Simulations System of Systems Verification, Validation and Accreditation Practices, Methodologies and Procedures

DTIC Science & Technology

2009-11-24

assisted by the Brigade Combat Team (BCT) Modernization effort, the use of Models and Simulations ( M &S) becomes more crucial in supporting major...in 2008 via a slice of the Current Force (CF) BCT structure. To ensure realistic operational context, a M &S System-of- Systems (SoS) level...messages, and constructive representation of platforms, vehicles, and terrain. The M &S federation also provided test control, data collection, and live

Procedural validity of the AUDADIS-5 depression, anxiety and post-traumatic stress disorder modules: substance abusers and others in the general population*

PubMed Central

Hasin, Deborah S.; Shmulewitz, Dvora; Stohl, Malka; Greenstein, Eliana; Aivadyan, Christina; Morita, Kara; Saha, Tulshi; Aharonovich, Efrat; Jung, Jeesun; Zhang, Haitao; Nunes, Edward V.; Grant, Bridget F.

2016-01-01

Background Little is known about the procedural validity of lay-administered, fully-structured assessments of depressive, anxiety and post-traumatic stress (PTSD) disorders in the general population as determined by comparison to clinical re-appraisal, and whether this differs between current regular substance abusers and others. We evaluated the procedural validity of the Alcohol Use Disorder and Associated Disabilities Interview Schedule, DSM-5 Version (AUDADIS-5) assessment of these disorders through clinician re-interviews. Methods Test-retest design among respondents from the National Epidemiologic Survey on Alcohol and Related Conditions-III (NESARC-III): (264 current regular substance abusers, 447 others). Clinicians blinded to AUDADIS-5 results administered the semi-structured Psychiatric Research Interview for Substance and Mental Disorders, DSM-5 version (PRISM-5). AUDADIS-5/PRISM-5 concordance was indicated by kappa (κ) for diagnoses and intraclass correlation coefficients (ICC) for dimensional measures (DSM-5 symptom or criterion counts). Results were compared between current regular substance abusers and others. Results AUDADIS-5 and PRISM-5 concordance for DSM-5 depressive disorders, anxiety disorders and PTSD was generally fair to moderate (κ =0.24–0.59), with concordance on dimensional scales much better (ICC=0.53–0.81). Concordance differed little between regular substance abusers and others. Conclusions AUDADIS-5/PRISM-5 concordance indicated procedural validity for the AUDADIS-5 among substance abusers and others, suggesting that AUDADIS-5 diagnoses of DSM-5 depressive, anxiety and PTSD diagnoses are informative measures in both groups in epidemiologic studies. The stronger concordance on dimensional measures supports the current movement towards dimensional psychopathology measures, suggesting that such measures provide important information for research in the NESARC-III and other datasets, and possibly for clinical purposes as well. PMID:25939727

Immediate effects of transcutaneous electrical nerve stimulation on six-minute walking test, Borg scale questionnaire and hemodynamic responses in patients with chronic heart failure.

PubMed

Ganguie, Majid Ashraf; Moghadam, Behrouz Attarbashi; Ghotbi, Nastaran; Shadmehr, Azadeh; Masoumi, Mohammad

2017-12-01

[Purpose] This study examined the immediate effects of transcutaneous electrical nerve stimulation on a six-minute walking test, Borg scale questionnaire and hemodynamic responses in patients with chronic heart failure. [Subjects and Methods] Thirty patients with stable systolic chronic heart failure came to the pathophysiology laboratory three times. The tests were randomly performed in three sessions. In one session, current was applied to the quadriceps muscles of both extremities for 30 minutes and a six-minute walking test was performed immediately afterward. In another session, the same procedure was followed except that the current intensity was set to zero. In the third session, the patients walked for six minutes without application of a current. The distance covered in each session was measured. At the end of each session, the subjects completed a Borg scale questionnaire. [Results] The mean distance traveled in the six-minute walking test and the mean score of the Borg scale questionnaire were significantly different across sessions. The mean systolic and diastolic pressures showed no significant differences across sessions. [Conclusion] The increase in distance traveled during the six-minute walking test and decrease in fatigue after the use of current may be due to a decrease in sympathetic overactivity and an increase in peripheral and muscular microcirculation in these patients.

Immediate effects of transcutaneous electrical nerve stimulation on six-minute walking test, Borg scale questionnaire and hemodynamic responses in patients with chronic heart failure

PubMed Central

Ganguie, Majid Ashraf; Moghadam, Behrouz Attarbashi; Ghotbi, Nastaran; Shadmehr, Azadeh; Masoumi, Mohammad

2017-01-01

[Purpose] This study examined the immediate effects of transcutaneous electrical nerve stimulation on a six-minute walking test, Borg scale questionnaire and hemodynamic responses in patients with chronic heart failure. [Subjects and Methods] Thirty patients with stable systolic chronic heart failure came to the pathophysiology laboratory three times. The tests were randomly performed in three sessions. In one session, current was applied to the quadriceps muscles of both extremities for 30 minutes and a six-minute walking test was performed immediately afterward. In another session, the same procedure was followed except that the current intensity was set to zero. In the third session, the patients walked for six minutes without application of a current. The distance covered in each session was measured. At the end of each session, the subjects completed a Borg scale questionnaire. [Results] The mean distance traveled in the six-minute walking test and the mean score of the Borg scale questionnaire were significantly different across sessions. The mean systolic and diastolic pressures showed no significant differences across sessions. [Conclusion] The increase in distance traveled during the six-minute walking test and decrease in fatigue after the use of current may be due to a decrease in sympathetic overactivity and an increase in peripheral and muscular microcirculation in these patients. PMID:29643590

The universal serial bus endoscope: design and initial clinical experience.

PubMed

Hernandez-Zendejas, Gregorio; Dobke, Marek K; Guerrerosantos, Jose

2004-01-01

Endoscopic forehead lift is a well-established procedure in aesthetic plastic surgery. Many agree that currently available video-endoscopic equipment is bulky, multipieced and sometimes cumbersome in the operating theater. A novel system, the Universal Serial Bus Endoscope (USBE) was designed to simplify and reduce the number of necessary equipment pieces in the endoscopic setup. The USBE is attached by a single cable to a Universal Serial Bus (USB) port of a laptop computer. A built-in miniaturized cold light source provides illumination. A built-in digital camera chip enables procedure recording. The real-time images and movies obtained with USBE are displayed on the computer's screen and recorded on the laptop's hard disk drive. In this study, 25 patients underwent endoscopic browlift using the USBE system to test its clinical usefulness, all with good results and without complications or need for revision. The USBE was found to be reliable and easier to use than current video-endoscope equipment. The operative time needed to complete the procedure by the authors was reduced approximately 50%. The design and main technical characteristics of the USBE are presented.

Effects of dividing attention on memory for declarative and procedural aspects of tool use.

PubMed

Roy, Shumita; Park, Norman W

2016-07-01

Tool-related knowledge and skills are supported by a complex set of memory processes that are not well understood. Some aspects of tools are mediated by either declarative or procedural memory, while other aspects may rely on an interaction of both systems. Although motor skill learning is believed to be primarily supported by procedural memory, there is debate in the current literature regarding the role of declarative memory. Growing evidence suggests that declarative memory may be involved during early stages of motor skill learning, although findings have been mixed. In the current experiment, healthy, younger adults were trained to use a set of novel complex tools and were tested on their memory for various aspects of the tools. Declarative memory encoding was interrupted by dividing attention during training. Findings showed that dividing attention during training was detrimental for subsequent memory for tool attributes as well as accurate demonstration of tool use and tool grasping. However, dividing attention did not interfere with motor skill learning, suggesting that declarative memory is not essential for skill learning associated with tools.

Preliminary Human-in-the-Loop Assessment of Procedures for Very-Closely-Spaced Parallel Runways

NASA Technical Reports Server (NTRS)

Verma, Savita; Lozito, Sandra C.; Ballinger, Deborah S.; Trot, Greg; Hardy, Gordon H.; Panda, Ramesh C.; Lehmer, Ronald D.; Kozon, Thomas E.

2010-01-01

Demand in the future air transportation system concept is expected to double or triple by 2025 [1]. Increasing airport arrival rates will help meet the growing demand that could be met with additional runways but the expansion airports is met with environmental challenges for the surrounding communities when using current standards and procedures. Therefore, changes to airport operations can improve airport capacity without adding runways. Building additional runways between current ones, or moving them closer, is a potential solution to meeting the increasing demand, as addressed by the Terminal Area Capacity Enhancing Concept (TACEC). TACEC requires robust technologies and procedures that need to be tested such that operations are not compromised under instrument meteorological conditions. The reduction of runway spacing for independent simultaneous operations dramatically exacerbates the criticality of wake vortex incursion and the calculation of a safe and proper breakout maneuver. The study presented here developed guidelines for such operations by performing a real-time, human-in-the-loop simulation using precision navigation, autopilot-flown approaches, with the pilot monitoring aircraft spacing and the wake vortex safe zone during the approach.

Evaluation of routine depopulation, cleaning, and disinfection procedures in the live bird markets, New York.

PubMed

Trock, Susan C; Gaeta, Michelle; Gonzalez, Annette; Pederson, Janice C; Senne, Dennis A

2008-03-01

During the past years surveillance for avian influenza has been conducted in the live bird markets (LBMs) in New York as well as other states along the east coast. Repeated attempts to eradicate H5 and H7 influenza from the New York markets have focused efforts on the LBMs themselves. Despite repeated mandatory market closures accompanied by cleaning and disinfecting (C/D) procedures, avian influenza virus continued to be isolated. In an effort to assess the adequacy of the C/D procedure, samples were collected in temporal proximity to the depopulation and C/D. Comparison of the pre-C/D (83% virus positive), at C/D approval (1.6% positive) and post-C/D testing (33% positive) indicate that the current procedures of C/D can be effective at eliminating these influenza viruses. However, reinfection via introduction of influenza-virus-positive birds can occur shortly after the market reopens.

Evaluation of Hands-Free Devices for Space Habitat Maintenance Procedures

NASA Technical Reports Server (NTRS)

Hoffman, R. B.; Twyford, E.; Conlee, C. S.; Litaker, H. L.; Solemn, J. A.; Holden

2007-01-01

Currently, International Space Station (ISS) crews use a laptop computer to display procedures for performing onboard maintenance tasks. This approach has been determined to be suboptimal. A heuristic evaluation and two studies have been completed to test commercial off-the-shelf (COTS) "near-eye" heads up displays (HUDs) for support of these types of maintenance tasks. In both studies, subjects worked through electronic procedures to perform simple maintenance tasks. As a result of the Phase I study, three HUDs were down-selected to one. In the Phase II study, the HUD was compared against two other electronic display devices - a laptop computer and an e-book reader. Results suggested that adjustability and stability of the HUD display were the most significant acceptability factors to consider for near-eye displays. The Phase II study uncovered a number of advantages and disadvantages of the HUD relative to the laptop and e-book reader for interacting with electronic procedures.

Hot-spot qualification testing of concentrator modules

NASA Technical Reports Server (NTRS)

Gonzalez, C. C.; Sugimura, R. S.; Ross, R. G., Jr.

1987-01-01

Results of a study to determine the hot-spot susceptibility of concentrator cells, to provide a hot-spot qualification test for concentrator modules, and to provide guidelines for reducing hot-spot susceptibility are presented. Hot-spot heating occurs in a photovoltaic module when the short-circuit current of a cell is lower than the string operating current, forcing the cell into reverse bias with a concurrent power dissipation. Although the basis for the concentrator-module hot-spot qualification test is the test developed for flat-plate modules, issues such as providing cell illumination introduce additional complexities into the testing procedure. The results indicate that the same general guidelines apply to protecting concentrator modules from hot-spot stressing as apply to flat-plate modules, and recommendations are made on the number of bypass diodes required per given number of series cells per module or source circuit. A method for determining the cell temperature in the laboratory or in the field is discussed.

A needle guidance system for biopsy and therapy using two-dimensional ultrasound

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bluvol, Nathan; Sheikh, Allison; Kornecki, Anat

2008-02-15

Image-guided needle biopsies are currently used to provide a definitive diagnosis of breast cancer; however, difficulties in tumor targeting exist as the ultrasound (United States) scan plane and biopsy needle must remain coplanar throughout the procedure to display the actual needle tip position. The additional time associated with aligning and maintaining this coplanar relationship results in increased patient discomfort. Biopsy procedural efficiency is further hindered since needle pathway interpretation is often difficult, especially for needle insertions at large depths that usually require multiple reinsertions. The authors developed a system that would increase the speed and accuracy of current breast biopsymore » procedures using readily available two-dimensional (2D) US technology. This system is composed of a passive articulated mechanical arm that attaches to a 2D US transducer. The arm is connected to a computer through custom electronics and software, which were developed as an interface for tracking the positioning of the mechanical components in real time. The arm couples to the biopsy needle and provides visual guidance for the physician performing the procedure in the form of a real-time projected needle pathway overlay on an US image of the breast. An agar test phantom, with stainless steel targets interspersed randomly throughout, was used to validate needle trajectory positioning accuracy. The biopsy needle was guided by both the software and hardware components to the targets. The phantom, with the needle inserted and device decoupled, was placed in an x-ray stereotactic mammography (SM) machine. The needle trajectory and bead target locations were determined in three dimensions from the SM images. Results indicated a mean needle trajectory accuracy error of 0.75{+-}0.42 mm. This is adequate to sample lesions that are <2 mm in diameter. Chicken tissue test phantoms were used to compare core needle biopsy procedure times between experienced radiologists and inexperienced resident radiologists using free-hand US and the needle guidance system. Cylindrical polyvinyl alcohol cryogel lesions, colored blue, were embedded in chicken tissue. Radiologists identified the lesions, visible as hypoechoic masses in the US images, and performed biopsy using a 14-gauge needle. Procedure times were compared based on experience and the technique performed. Using a pair-wise t test, lower biopsy procedure times were observed when using the guidance system versus the free-hand technique (t=12.59, p<0.001). The authors believe that with this improved biopsy guidance they will be able to reduce the ''false negative'' rate of biopsies, especially in the hands of less experienced physicians.« less

Biodegradability study of high-erucic-acid-rapeseed-oil-based lubricant additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, E.; Crawford, R.L.; Shanahan, A.

1995-12-31

A variety of high-erucic-acid-rapeseed (HEAR)-oil-based lubricants, lubricant additives, and greases were examined for biodegradability at the University of Idaho Center for Hazardous Waste Remediation Research. Two standard biodegradability tests were employed, a currently accepted US Environmental Protection Agency (EPA) protocol and the Sturm Test. As is normal for tests that employ variable inocula such as sewage as a source of microorganisms, these procedures yielded variable results from one repetition to another. However, a general trend of rapid and complete biodegradability of the HEAR-oil-based materials was observed.

Electromagnetic propulsion test facility

NASA Technical Reports Server (NTRS)

Gooder, S. T.

1984-01-01

A test facility for the exploration of electromagnetic propulsion concept is described. The facility is designed to accommodate electromagnetic rail accelerators of various lengths (1 to 10 meters) and to provide accelerating energies of up to 240 kiloJoules. This accelerating energy is supplied as a current pulse of hundreds of kiloAmps lasting as long as 1 millisecond. The design, installation, and operating characteristics of the pulsed energy system are discussed. The test chamber and its operation at pressures down to 1300 Pascals (10 mm of mercury) are described. Some aspects of safety (interlocking, personnel protection, and operating procedures) are included.

BPM Motors in Residential Gas Furnaces: What are theSavings?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutz, James; Franco, Victor; Lekov, Alex

2006-05-12

Residential gas furnaces contain blowers to distribute warm air. Currently, furnace blowers use either a Permanent Split Capacitor (PSC) or a Brushless Permanent Magnet (BPM) motor. Blowers account for the majority of furnace electricity consumption. Therefore, accurate determination of the blower electricity consumption is important for understanding electricity consumption of furnaces. The electricity consumption of blower motors depends on the static pressure across the blower. This paper examines both types of blower motors in non-condensing non-weatherized gas furnaces at a range of static pressures. Fan performance data is based on manufacturer product literature and laboratory tests. We use field-measured staticmore » pressure in ducts to get typical system curves to calculate how furnaces would operate in the field. We contrast this with the electricity consumption of a furnace blower operating under the DOE test procedure and manufacturer rated conditions. Furnace electricity use is also affected by operating modes that happen at the beginning and end of each furnace firing cycle. These operating modes are the pre-purge and post-purge by the draft inducer, the on-delay and off-delay of the blower, and the hot surface ignitor operation. To accurately calculate this effect, we use the number of firing cycles in a typical California house in the Central Valley of California. Cooling hours are not considered in the DOE test procedure. We also account for furnace blower use by the air conditioner and stand-by power. Overall BPM motors outperform PSC motors, but the total electricity savings are significantly less than projected using the DOE test procedure conditions. The performance gains depend on the static pressure of the household ducts, which are typically much higher than in the test procedures.« less

10 CFR 431.154 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Test procedures. 431.154 Section 431.154 Energy DEPARTMENT... EQUIPMENT Commercial Clothers Washers Test Procedures § 431.154 Test procedures. The test procedures for residential clothes washers in Appendix J1 to subpart B of part 430 of this title shall be used to test...

[Modern Diagnosis and Therapy of the rhinitis allergica].

PubMed

Hauswald, B; Yarin, Y M

2015-05-01

The prevalence of allergic diseases is increasing worldwide. The highest increase rate is observed in rhinitis allergica. Apart from the anamnesis, the diagnosis relies mainly on skin tests, laboratory analyses and if necessary provocation tests. Symptomatic and causal therapy with abstention and specific immunotherapy are available as therapeutic means. Specific immunotherapy should be aspired as the method of choice. It is comprised of subcutane and sublingular immunity therapy. Usually native allergens and allergoids are used as therapeutics. Recombinant allergens are currently under development. Modern therapy procedures involving these drugs consist of year-round or pre- and co-seasonal treatment which spans at least 3-4 years. In cases of polyvalent allergy, different types of drugs and therapy procedures can be combined. The future of rhinitis allergica treatment lies in further development of specific immunotherapy. © Georg Thieme Verlag KG Stuttgart · New York.

One normal void and residual following MUS surgery is all that is necessary in most patients.

PubMed

Ballard, Paul; Shawer, Sami; Anderson, Colette; Khunda, Aethele

2018-04-01

There is considerable variation worldwide on how the assessment of voiding function is performed following midurethral sling (MUS) surgery. There is potentially a financial cost, and reduction in efficiency when patient discharge is delayed. Using our current practice of two normal void and residual (V&R) readings before discharge, the aim of this retrospective study was to evaluate the likelihood of an abnormal second V&R test if the first V&R test was normal in order to determine if a policy of discharge after only one satisfactory V&R test is reasonable. Data from 400 patients who had had MUS surgery with or without other procedures were collected. Our unit protocol included two consecutive voids of greater than 200 ml with residuals less than 150 ml before discharge. The patients were divided into the following groups: MUS only, MUS plus anterior colporrhaphy (AR) plus any other procedures (MUS/AR), and MUS with any non-AR procedures (MUS+). Complete datasets were available for 335 patients. Once inadequate tests (low volume voids <200 ml) had been excluded (28% overall), the likelihood of an abnormal second V&R test if the first test was normal was 7.1% overall, but 3.6% for MUS, 11.5% for MUS/AR and 8.6% for MUS+. The findings in the MUS-only group indicate that it is probably safe to discharge patients after one satisfactory V&R test, as long as safety measures such as 'open access' are available so that patients have unhindered readmission if problems arise.

A Soil-free System for Assaying Nematicidal Activity of Chemicals

PubMed Central

Preiser, F. A.; Babu, J. R.; Haidri, A. A.

1981-01-01

A biological assay system for studying the nematicidal activity of chemicals has been devised using a model consisting of cucumber (Cucumis sativus L. cv. Long Marketer) seedlings growing in the diSPo® growth-pouch apparatus. Meloidogyne incognita was used as the test organism. The response was quantified in terms of the numbers of galls produced. Statistical procedures were applied to estimate the ED50 values of currently available nematicides. This system permits accurate quantification of galling and requires much less space and effort than the currently used methods. PMID:19300800

A Soil-free System for Assaying Nematicidal Activity of Chemicals.

PubMed

Preiser, F A; Babu, J R; Haidri, A A

1981-10-01

A biological assay system for studying the nematicidal activity of chemicals has been devised using a model consisting of cucumber (Cucumis sativus L. cv. Long Marketer) seedlings growing in the diSPo(R) growth-pouch apparatus. Meloidogyne incognita was used as the test organism. The response was quantified in terms of the numbers of galls produced. Statistical procedures were applied to estimate the ED(50) values of currently available nematicides. This system permits accurate quantification of galling and requires much less space and effort than the currently used methods.

The antidepressant effect of an antiulcer pentadecapeptide BPC 157 in Porsolt's test and chronic unpredictable stress in rats. A comparison with antidepressants.

PubMed

Sikiric, P; Separovic, J; Buljat, G; Anic, T; Stancic-Rokotov, D; Mikus, D; Marovic, A; Prkacin, I; Duplancic, B; Zoricic, I; Aralica, G; Lovric-Bencic, M; Ziger, T; Perovic, D; Rotkvic, I; Mise, S; Hanzevacki, M; Hahn, V; Seiwerth, S; Turkovic, B; Grabarevic, Z; Petek, M; Rucman, R

2000-01-01

Various antidepressants have antiulcer activity. Likewise, the models currently used in ulcers and depression disorders research have a considerable degree of similarity. Therefore, the possibility that depression disorders could be effectively influenced by a primary antiulcer agent with a cyto/organoprotective activity, such as the novel stomach pentadecapeptide BPC 157, was investigated in two rat depression assays. First, a forced swimming test (a Porsolt's procedure) was used. As a more severe procedure, chronic unpredictable stress (after 5 d of unpredictable stress protocol, once daily drug application during stress procedure, open field-immobility test assessment at fourth or sixth day of medication) was used. In a forced swimming test, a reduction of the immobility time in BPC 157 (10 microg, 10 ng x kg(-1) i.p.) treated rats corresponds to the activity of the 15 mg or 40 mg (i.p.) of conventional antidepressants, imipramine or nialamide, respectively, given according to the original Porsolt's protocol. In chronic unpredictable stress procedure, particular aggravation of experimental conditions markedly affected the conventional antidepressant activity, whereas BPC 157 effectiveness was continuously present. The effect of daily imipramine (30 mg) medication could be seen only after a more prolonged period, but not after a shorter period (i.e., 4-d protocol). In these conditions, no delay in the effectiveness was noted in BPC 157 medication and a reduction of the immobility of chronically stressed rats was noted after both 4 and 6 d of BPC 157 (10 microg, 10 ng) medication.

Radial particle-size segregation during packing of particulates into cylindrical containers

USGS Publications Warehouse

Ripple, C.D.; James, R.V.; Rubin, J.

1973-01-01

In a series of experiments, soil materials were placed in long cylindrical containers, using various packing procedures. Soil columns produced by deposition and simultaneous vibratory compaction were dense and axially uniform, but showed significant radial segregation of particle sizes. Similar results were obtained with deposition and simultaneous impact-type compaction when the impacts resulted in significant container "bouncing". The latter procedure, modified to minimize "bouncing" produced dense, uniform soil columns, showing little radial particle-size segregation. Other procedures tested (deposition alone and deposition followed by compaction) did not result in radial segregation, but produced columns showing either relatively low or axially nonuniform densities. Current data suggest that radial particle-size segregation is mainly due to vibration-induced particle circulation in which particles of various sizes have different circulation rates and paths. ?? 1973.

Synthesis of Sine-on-Random vibration profiles for accelerated life tests based on fatigue damage spectrum equivalence

NASA Astrophysics Data System (ADS)

Angeli, Andrea; Cornelis, Bram; Troncossi, Marco

2018-03-01

In many real life environments, mechanical and electronic systems are subjected to vibrations that may induce dynamic loads and potentially lead to an early failure due to fatigue damage. Thus, qualification tests by means of shakers are advisable for the most critical components in order to verify their durability throughout the entire life cycle. Nowadays the trend is to tailor the qualification tests according to the specific application of the tested component, considering the measured field data as reference to set up the experimental campaign, for example through the so called "Mission Synthesis" methodology. One of the main issues is to define the excitation profiles for the tests, that must have, besides the (potentially scaled) frequency content, also the same damage potential of the field data despite being applied for a limited duration. With this target, the current procedures generally provide the test profile as a stationary random vibration specified by a Power Spectral Density (PSD). In certain applications this output may prove inadequate to represent the nature of the reference signal, and the procedure could result in an unrealistic qualification test. For instance when a rotating part is present in the system the component under analysis may be subjected to Sine-on-Random (SoR) vibrations, namely excitations composed of sinusoidal contributions superimposed to random vibrations. In this case, the synthesized test profile should preserve not only the induced fatigue damage but also the deterministic components of the environmental vibration. In this work, the potential advantages of a novel procedure to synthesize SoR profiles instead of PSDs for qualification tests are presented and supported by the results of an experimental campaign.

Noninvasive imaging systems for gametes and embryo selection in IVF programs: a review.

PubMed

Omidi, Marjan; Faramarzi, Azita; Agharahimi, Azam; Khalili, Mohammad Ali

2017-09-01

Optimizing the efficiency of the in vitro fertilization procedure by improving pregnancy rates and reducing the risks of multiple pregnancies simultaneously are the primary goals of the current assisted reproductive technology program. With the move to single embryo transfers, the need for more cost-effective and noninvasive methods for embryo selection prior to transfer is paramount. These aims require advancement in a more acquire gametes/embryo testing and selection procedures using high-tech devices. Therefore, the aim of the present review is to evaluate the efficacy of noninvasive imaging systems in the current literatures, focusing on the potential clinical application in infertile patients undergoing assisted reproductive technology treatments. In this regards, three advanced imaging systems of motile sperm organelle morphology examination, polarization microscopy and time-lapse monitoring for the best selection of the gametes and preimplantation embryos are introduced in full. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

40 CFR 63.694 - Testing methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 11 2014-07-01 2014-07-01 false Testing methods and procedures. 63.694....694 Testing methods and procedures. (a) This section specifies the testing methods and procedures... this subpart, the testing methods and procedures are specified in paragraph (b) of this section. (2) To...

40 CFR 86.425-78 - Test procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 19 2013-07-01 2013-07-01 false Test procedures. 86.425-78 Section 86... Later New Motorcycles, General Provisions § 86.425-78 Test procedures. (a) Motorcycle emission test procedures are found in subpart F. (b) The Administrator may prescribe emission test procedures for any...

40 CFR 86.425-78 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 19 2014-07-01 2014-07-01 false Test procedures. 86.425-78 Section 86... Later New Motorcycles, General Provisions § 86.425-78 Test procedures. (a) Motorcycle emission test procedures are found in subpart F. (b) The Administrator may prescribe emission test procedures for any...

40 CFR 86.425-78 - Test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 19 2012-07-01 2012-07-01 false Test procedures. 86.425-78 Section 86... Later New Motorcycles, General Provisions § 86.425-78 Test procedures. (a) Motorcycle emission test procedures are found in subpart F. (b) The Administrator may prescribe emission test procedures for any...

40 CFR 600.111-93 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Test procedures. 600.111-93 Section... Emission Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.111-93 Test procedures. (a) The test procedures to be followed for generation of the city fuel economy data are those...

40 CFR 90.508 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Test procedures. 90.508 Section 90.508....508 Test procedures. (a) For nonroad engines subject to the provisions of this subpart, the prescribed test procedures are the appropriate small SI engine test procedures as described in subpart E of this...

40 CFR 89.508 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Test procedures. 89.508 Section 89.508... Test procedures. (a)(1) For nonroad engines subject to the provisions of this subpart, the prescribed test procedures are the nonroad engine 8-mode test procedure as described in subpart E of this part...

40 CFR 600.111-80 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Test procedures. 600.111-80 Section... Emission Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.111-80 Test procedures. (a) The test procedures to be followed for generation of the city fuel economy data are those...

21 CFR 355.70 - Testing procedures for fluoride dentifrice drug products.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Testing procedures for fluoride dentifrice drug... Procedures § 355.70 Testing procedures for fluoride dentifrice drug products. (a) A fluoride dentifrice drug... tests: Enamel solubility reduction or fluoride enamel uptake. The testing procedures for these...

21 CFR 355.70 - Testing procedures for fluoride dentifrice drug products.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Testing procedures for fluoride dentifrice drug... Procedures § 355.70 Testing procedures for fluoride dentifrice drug products. (a) A fluoride dentifrice drug... tests: Enamel solubility reduction or fluoride enamel uptake. The testing procedures for these...

New Rock Abrasivity Test Method for Tool Life Assessments on Hard Rock Tunnel Boring: The Rolling Indentation Abrasion Test (RIAT)

NASA Astrophysics Data System (ADS)

Macias, F. J.; Dahl, F.; Bruland, A.

2016-05-01

The tunnel boring machine (TBM) method has become widely used and is currently an important presence within the tunnelling industry. Large investments and high geological risk are involved using TBMs, and disc cutter consumption has a great influence on performance and cost, especially in hard rock conditions. Furthermore, reliable cutter life assessments facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory tests for rock abrasivity assessments are needed. A new abrasivity test method by rolling disc named Rolling Indentation Abrasion Test (RIAT) has been developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than the traditionally used methods. Wear by rolling contact on intact rock samples is introduced and several rock types, covering a wide rock abrasiveness range, have been tested by RIAT. The RIAT procedure indicates a great ability of the testing method to assess abrasive wear on rolling discs. In addition and to evaluate the newly developed RIAT test method, a comprehensive laboratory testing programme including the most commonly used abrasivity test methods and the mineral composition were carried out. Relationships between the achieved results from conventional testing and RIAT results have been analysed.

Contributions of internationalization to psychology: toward a global and inclusive discipline.

PubMed

van de Vijver, Fons J R

2013-11-01

In this article I define and describe the current state of internationalization in psychology. Internationalization refers here to the approach in which existing or new psychological theories, methods, procedures, or data across cultures are synthesized so as to create a more culture-informed, inclusive, and globally applicable science and profession. This approach is essential to advance psychology beyond its Euro-American context of development and to achieve a more global applicability of its theories and professional procedures. Internationalization already has led to a better integration of cultural aspects in various psychological theories, to more insight into how to deal with methodological aspects of intact group comparisons (such as bias and equivalence), and to the development of guidelines in areas such as test development, test adaptations, ethics codes, and Internet testing. I review systemic and scientific climate factors in psychology that thwart the progress of internationalization, and conclude by suggesting methods of enhancing internationalization, which is essential for developing a truly universal psychology.

Inter-laboratory assessment of a harmonized zebrafish developmental toxicology assay - progress report on phase I.

PubMed

Gustafson, A-L; Stedman, D B; Ball, J; Hillegass, J M; Flood, A; Zhang, C X; Panzica-Kelly, J; Cao, J; Coburn, A; Enright, B P; Tornesi, M B; Hetheridge, M; Augustine-Rauch, K A

2012-04-01

This report provides a progress update of a consortium effort to develop a harmonized zebrafish developmental toxicity assay. Twenty non-proprietary compounds (10 animal teratogens and 10 animal non-teratogens) were evaluated blinded in 4 laboratories. Zebrafish embryos from pond-derived and cultivated strain wild types were exposed to the test compounds for 5 days and subsequently evaluated for lethality and morphological changes. Each of the testing laboratories achieved similar overall concordance to the animal data (60-70%). Subsequent optimization procedures to improve the overall concordance focused on compound formulation and test concentration adjustments, chorion permeation and number of replicates. These optimized procedures were integrated into a revised protocol and all compounds were retested in one lab using embryos from pond-derived zebrafish and achieved 85% total concordance. To further assess assay performance, a study of additional compounds is currently in progress at two laboratories using embryos from pond-derived and cultivated-strain wild type zebrafish. Copyright © 2011 Elsevier Inc. All rights reserved.

Digital avionics susceptibility to high energy radio frequency fields

NASA Astrophysics Data System (ADS)

Larsen, William E.

Generally, noncritical avionic systems for transport category aircraft have been designed to meet radio frequency (RF) susceptibility requirements set forth in RTCA DO 160B, environmental conditions and test procedures for airborne equipment. Section 20 of this document controls the electromagnetic interference (EMI) hardening for avionics equipment to levels of 1 and 2 V/m. Currently, US equipment manufacturers are designing flight-critical fly-by-wire avionics to a much higher level. The US Federal Aviation Administration (FAA) has requested that the RTCA SC-135 high-energy radio frequency (HERF) working group develop appropriate testing procedures for section 20 of RTCA DO 160B for radiated and conducted susceptibility at the box and systems level. The FAA has also requested the SAE AE4R committee to address installed systems testing, airframe shielding effects and RF environment monitoring. Emitters of interest include radar (ground, ship, and aircraft) commercial broadcast and TV station, mobile communication, and other transmitters that could possibly affect commercial aircraft.

75 FR 22577 - Proposed Rule of Agency Procedure No. 1: Procedures for Voting by Circulation Version 2.0

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-29

... deadlines, the current policy limits EAC's ability to address the rare situations that require swift action... Procedure No. 1: Procedures for Voting by Circulation Version 2.0. EAC's current Proposed Rule of Agency...

Prediction of SFL Interruption Performance from the Results of Arc Simulation during High-Current Phase

NASA Astrophysics Data System (ADS)

Lee, Jong-Chul; Lee, Won-Ho; Kim, Woun-Jea

2015-09-01

The design and development procedures of SF6 gas circuit breakers are still largely based on trial and error through testing although the development costs go higher every year. The computation cannot cover the testing satisfactorily because all the real processes arc not taken into account. But the knowledge of the arc behavior and the prediction of the thermal-flow inside the interrupters by numerical simulations are more useful than those by experiments due to the difficulties to obtain physical quantities experimentally and the reduction of computational costs in recent years. In this paper, in order to get further information into the interruption process of a SF6 self-blast interrupter, which is based on a combination of thermal expansion and the arc rotation principle, gas flow simulations with a CFD-arc modeling are performed during the whole switching process such as high-current period, pre-current zero period, and current-zero period. Through the complete work, the pressure-rise and the ramp of the pressure inside the chamber before current zero as well as the post-arc current after current zero should be a good criterion to predict the short-line fault interruption performance of interrupters.

An automated qualification framework for the MeerKAT CAM (Control-And-Monitoring)

NASA Astrophysics Data System (ADS)

van den Heever, Lize; Marais, Neilen; Slabber, Martin

2016-08-01

This paper introduces and discusses the design of an Automated Qualification Framework (AQF) that was developed to automate as much as possible of the formal Qualification Testing of the Control And Monitoring (CAM) subsystem of the 64 dish MeerKAT radio telescope currently under construction in the Karoo region of South Africa. The AQF allows each Integrated CAM Test to reference the MeerKAT CAM requirement and associated verification requirement it covers and automatically produces the Qualification Test Procedure and Qualification Test Report from the test steps and evaluation steps annotated in the Integrated CAM Tests. The MeerKAT System Engineers are extremely happy with the AQF results, but mostly by the approach and process it enforces.

Toddler test or procedure preparation

MedlinePlus

Preparing toddler for test/procedure; Test/procedure preparation - toddler; Preparing for a medical test or procedure - toddler ... Before the test, know that your child will probably cry. Even if you prepare, your child may feel some discomfort or ...

Mechanical grading of round timber beams

Treesearch

David W. Green; Thomas M. Gorman; James W. Evans; Joseph F. Murphy

2006-01-01

Current procedures used to sort round timber beams into structural grades rely on visual grading methods and property assignments based on modification of clear wood properties. This study provides the technical basis for mechanical grading of 228 mm (9 in.) diameter round timbers. Test results on 225 round Engelmann spruce–alpine fir–lodgepole pine beams demonstrate...

Massive Memory Revisited: Limitations on Storage Capacity for Object Details in Visual Long-Term Memory

ERIC Educational Resources Information Center

Cunningham, Corbin A.; Yassa, Michael A.; Egeth, Howard E.

2015-01-01

Previous work suggests that visual long-term memory (VLTM) is highly detailed and has a massive capacity. However, memory performance is subject to the effects of the type of testing procedure used. The current study examines detail memory performance by probing the same memories within the same subjects, but using divergent probing methods. The…

Hydrology for urban land planning - A guidebook on the hydrologic effects of urban land use

USGS Publications Warehouse

Leopold, Luna Bergere

1968-01-01

The application of current knowledge of the hydrologic effects of urbanization to the Brandywine should be viewed as a forecast of conditions which may be expected as urbanization proceeds. By making such forecasts in advance of actual urban development, the methods can be tested, data can be extended, and procedures improved as verification becomes possible.

Roux-en-Y gastric bypass does not affect daily water intake or the drinking response to dipsogenic stimuli in rats.

PubMed

Marshall, Anikó; Santollo, Jessica; Corteville, Caroline; Lutz, Thomas A; Daniels, Derek

2014-07-15

Bariatric surgery is currently the most effective treatment for severe obesity, and Roux-en-Y gastric bypass (RYGB) is the most common approach in the United States and worldwide. Many studies have documented the changes in body weight, food intake, and glycemic control associated with the procedure. Although dehydration is commonly listed as a postoperative complication, little focus has been directed to testing the response to dipsogenic treatments after RYGB. Accordingly, we used a rat model of RYGB to test for procedure-induced changes in daily water intake and in the response to three dipsogenic treatments: central administration of ANG II, peripheral injection of hypertonic saline, and overnight water deprivation. We did not find any systematic differences in daily water intake of sham-operated and RYGB rats, nor did we find any differences in the response to the dipsogenic treatments. The results of these experiments suggest that RYGB does not impair thirst responses and does not enhance any satiating effect of water intake. Furthermore, these data support the current view that feedback from the stomach is unnecessary for the termination of drinking behavior and are consistent with a role of orosensory or postgastric feedback.

Recurrence Quantification Analysis of Sentence-Level Speech Kinematics.

PubMed

Jackson, Eric S; Tiede, Mark; Riley, Michael A; Whalen, D H

2016-12-01

Current approaches to assessing sentence-level speech variability rely on measures that quantify variability across utterances and use normalization procedures that alter raw trajectory data. The current work tests the feasibility of a less restrictive nonlinear approach-recurrence quantification analysis (RQA)-via a procedural example and subsequent analysis of kinematic data. To test the feasibility of RQA, lip aperture (i.e., the Euclidean distance between lip-tracking sensors) was recorded for 21 typically developing adult speakers during production of a simple utterance. The utterance was produced in isolation and in carrier structures differing just in length or in length and complexity. Four RQA indices were calculated: percent recurrence (%REC), percent determinism (%DET), stability (MAXLINE), and stationarity (TREND). Percent determinism (%DET) decreased only for the most linguistically complex sentence; MAXLINE decreased as a function of linguistic complexity but increased for the longer-only sentence; TREND decreased as a function of both length and linguistic complexity. This research note demonstrates the feasibility of using RQA as a tool to compare speech variability across speakers and groups. RQA offers promise as a technique to assess effects of potential stressors (e.g., linguistic or cognitive factors) on the speech production system.

Recurrence Quantification Analysis of Sentence-Level Speech Kinematics

PubMed Central

Tiede, Mark; Riley, Michael A.; Whalen, D. H.

2016-01-01

Purpose Current approaches to assessing sentence-level speech variability rely on measures that quantify variability across utterances and use normalization procedures that alter raw trajectory data. The current work tests the feasibility of a less restrictive nonlinear approach—recurrence quantification analysis (RQA)—via a procedural example and subsequent analysis of kinematic data. Method To test the feasibility of RQA, lip aperture (i.e., the Euclidean distance between lip-tracking sensors) was recorded for 21 typically developing adult speakers during production of a simple utterance. The utterance was produced in isolation and in carrier structures differing just in length or in length and complexity. Four RQA indices were calculated: percent recurrence (%REC), percent determinism (%DET), stability (MAXLINE), and stationarity (TREND). Results Percent determinism (%DET) decreased only for the most linguistically complex sentence; MAXLINE decreased as a function of linguistic complexity but increased for the longer-only sentence; TREND decreased as a function of both length and linguistic complexity. Conclusions This research note demonstrates the feasibility of using RQA as a tool to compare speech variability across speakers and groups. RQA offers promise as a technique to assess effects of potential stressors (e.g., linguistic or cognitive factors) on the speech production system. PMID:27824987

[Quality of the Early Cervical Cancer Detection Program in the State of Nuevo León].

PubMed

Salinas-Martínez, A M; Villarreal-Ríos, E; Garza-Elizondo, M E; Fraire-Gloria, J M; López-Franco, J J; Barboza-Quintana, O

1997-01-01

To determine the quality of the Early Cervical Cancer Detection Program in the state of Nuevo León. A random selection of 4791 cytologic reports were analyzed, emitted by the State Ministry of Health, the University Hospital and the Mexican Institute for Social Security early cervical cancer detection modules. Pap tests of women with hysterectomy, current pregnancy, menopause or positive result were excluded. Quality was measured with previously defined standards. Analysis included, besides univariate statistics, tests of significance for proportions and means. The quality of the program was fairly satisfactory at the level of the State. The quality of the sampling procedure was low; 39.9% of the tests contained endocervical cells. Quality of coverage was low; 15.6% were women 25+years with first time Pap test. Quality of opportunity was high; 8.5 +/- 7 weekdays between the date of the pap smear and the interpretation date. Strategies are needed to increase the impact of the state program, such as improving the sampling procedure and the coverage quality levels.

Using population-based data to predict the impact of introducing noninvasive prenatal diagnosis for Down syndrome.

PubMed

Susman, Marleen R; Amor, David J; Muggli, Evelyne; Jaques, Alice M; Halliday, Jane

2010-05-01

To compare the number and types of chromosome abnormalities prenatally diagnosed and the number of invasive procedures between current prenatal testing pathways and a pathway where noninvasive prenatal diagnosis for Down syndrome replaces Down syndrome screening tests. Numbers and types of chromosome abnormalities for each referral category were extracted from prenatal diagnostic testing reports routinely collected in Victoria, Australia, in 2006 and 2007. These data were then applied to the proposed implementation strategy. If noninvasive prenatal diagnosis for Down syndrome had replaced Down syndrome screening tests in 2006 and 2007, in Victoria, there would have been 25 (7%) additional Down syndrome diagnosed, 6896 (84%) fewer invasive procedures, and 231 (56%) non-Down syndrome chromosome abnormalities no longer detected. These include trisomy 13, trisomy 18, sex chromosome abnormalities, balanced and unbalanced rearrangements, polyploidy, and mosaic results. The potential loss of information about chromosome abnormalities other than Down syndrome with noninvasive prenatal diagnosis compared with full karyotyping with traditional prenatal diagnosis should be considered when planning for the implementation of new technologies.

Building Energy Simulation Test for Existing Homes (BESTEST-EX) (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judkoff, R.; Neymark, J.; Polly, B.

2011-12-01

This presentation discusses the goals of NREL Analysis Accuracy R&D; BESTEST-EX goals; what BESTEST-EX is; how it works; 'Building Physics' cases; 'Building Physics' reference results; 'utility bill calibration' cases; limitations and potential future work. Goals of NREL Analysis Accuracy R&D are: (1) Provide industry with the tools and technical information needed to improve the accuracy and consistency of analysis methods; (2) Reduce the risks associated with purchasing, financing, and selling energy efficiency upgrades; and (3) Enhance software and input collection methods considering impacts on accuracy, cost, and time of energy assessments. BESTEST-EX Goals are: (1) Test software predictions of retrofitmore » energy savings in existing homes; (2) Ensure building physics calculations and utility bill calibration procedures perform up to a minimum standard; and (3) Quantify impact of uncertainties in input audit data and occupant behavior. BESTEST-EX is a repeatable procedure that tests how well audit software predictions compare to the current state of the art in building energy simulation. There is no direct truth standard. However, reference software have been subjected to validation testing, including comparisons with empirical data.« less

The Current Status of Percutaneous Coronary Intervention in Korea: Based on Year 2014 Cohort of Korean Percutaneous Coronary Intervention (K-PCI) Registry

PubMed Central

Jang, Jae-Sik; Han, Kyoo-Rok; Moon, Keon-Woong; Jeon, Dong Woon; Shin, Dong-Ho; Kim, Jung-Sun; Park, Duk-Woo; Kang, Hyun-Jae; Kim, Juhan; Bae, Jang-Whan; Hur, Seung-Ho; Kim, Byung Ok; Choi, Donghoon; Gwon, Hyeon-Cheol

2017-01-01

Background and Objectives Although several multicenter registries have evaluated percutaneous coronary intervention (PCI) procedures in Korea, those databases have been limited by non-standardized data collection and lack of uniform reporting methods. We aimed to collect and report data from a standardized database to analyze PCI procedures throughout the country. Materials and Methods Both clinical and procedural data, as well as clinical outcomes data during hospital stay, were collected based on case report forms that used a standard set of 54 data elements. This report is based on 2014 Korean PCI registry cohort data. Results A total of 92 hospitals offered data on 44967 PCI procedures. The median age was 66.0 interquartile range 57.0-74.0 years, and 70.3% were men. Thirty-eight percent of patients presented with acute myocardial infarction and one-third of all PCI procedures were performed in an urgent or emergency setting. Non-invasive stress tests were performed in 13.9% of cases, while coronary computed tomography angiography was used in 13.7% of cases prior to PCI. Radial artery access was used in 56.1% of all PCI procedures. Devices that used PCI included drug-eluting stent, plain old balloon angioplasty, drug-eluting balloon, and bare-metal stent (around 91%, 19%, 6%, and 1% of all procedures, respectively). The incidences of in-hospital death, non-fatal myocardial infarction, and stroke were 2.3%, 1.6%, and 0.2%, respectively. Conclusion These data may provide an overview of the current PCI practices and in-hospital outcomes in Korea and could be used as a foundation for developing treatment guidelines and nationwide clinical research. PMID:28567083

The Current Status of Percutaneous Coronary Intervention in Korea: Based on Year 2014 Cohort of Korean Percutaneous Coronary Intervention (K-PCI) Registry.

PubMed

Jang, Jae-Sik; Han, Kyoo-Rok; Moon, Keon-Woong; Jeon, Dong Woon; Shin, Dong-Ho; Kim, Jung-Sun; Park, Duk-Woo; Kang, Hyun-Jae; Kim, Juhan; Bae, Jang-Whan; Hur, Seung-Ho; Kim, Byung Ok; Choi, Donghoon; Gwon, Hyeon-Cheol; Kim, Hyo-Soo

2017-05-01

Although several multicenter registries have evaluated percutaneous coronary intervention (PCI) procedures in Korea, those databases have been limited by non-standardized data collection and lack of uniform reporting methods. We aimed to collect and report data from a standardized database to analyze PCI procedures throughout the country. Both clinical and procedural data, as well as clinical outcomes data during hospital stay, were collected based on case report forms that used a standard set of 54 data elements. This report is based on 2014 Korean PCI registry cohort data. A total of 92 hospitals offered data on 44967 PCI procedures. The median age was 66.0 interquartile range 57.0-74.0 years, and 70.3% were men. Thirty-eight percent of patients presented with acute myocardial infarction and one-third of all PCI procedures were performed in an urgent or emergency setting. Non-invasive stress tests were performed in 13.9% of cases, while coronary computed tomography angiography was used in 13.7% of cases prior to PCI. Radial artery access was used in 56.1% of all PCI procedures. Devices that used PCI included drug-eluting stent, plain old balloon angioplasty, drug-eluting balloon, and bare-metal stent (around 91%, 19%, 6%, and 1% of all procedures, respectively). The incidences of in-hospital death, non-fatal myocardial infarction, and stroke were 2.3%, 1.6%, and 0.2%, respectively. These data may provide an overview of the current PCI practices and in-hospital outcomes in Korea and could be used as a foundation for developing treatment guidelines and nationwide clinical research.

40 CFR 86.884-5 - Test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 20 2012-07-01 2012-07-01 false Test procedures. 86.884-5 Section 86... New Diesel Heavy-Duty Engines; Smoke Exhaust Test Procedure § 86.884-5 Test procedures. The procedures described in this and subsequent sections will be the test program to determine the conformity of engines...

40 CFR 86.608-98 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 19 2014-07-01 2014-07-01 false Test procedures. 86.608-98 Section 86... New Light-Duty Vehicles, Light-Duty Trucks, and Heavy-Duty Vehicles § 86.608-98 Test procedures. (a) The prescribed test procedures are the Federal Test Procedure, as described in subpart B of this part...

40 CFR 86.608-98 - Test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 20 2012-07-01 2012-07-01 false Test procedures. 86.608-98 Section 86... Auditing of New Light-Duty Vehicles, Light-Duty Trucks, and Heavy-Duty Vehicles § 86.608-98 Test procedures. (a) The prescribed test procedures are the Federal Test Procedure, as described in subpart B and/or...

14 CFR Appendix F to Part 23 - Test Procedure

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Test Procedure F Appendix F to Part 23...—Test Procedure Part I—Acceptable Test Procedure for Self-Extinguishing Materials for Showing Compliance With §§ 23.853, 23.855, and 23.1359 Acceptable test procedure for self-extinguishing materials for...

40 CFR 600.111-08 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Test procedures. 600.111-08 Section... Emission Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.111-08 Test procedures. This section provides test procedures for the FTP, highway, US06, SC03, and the cold temperature FTP...

14 CFR Appendix F to Part 23 - Test Procedure

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Test Procedure F Appendix F to Part 23...—Test Procedure Part I—Acceptable Test Procedure for Self-Extinguishing Materials for Showing Compliance With §§ 23.853, 23.855, and 23.1359 Acceptable test procedure for self-extinguishing materials for...

40 CFR 86.884-5 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 19 2014-07-01 2014-07-01 false Test procedures. 86.884-5 Section 86... Heavy-Duty Engines; Smoke Exhaust Test Procedure § 86.884-5 Test procedures. The procedures described in this and subsequent sections will be the test program to determine the conformity of engines with the...

40 CFR 51.357 - Test procedures and standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false Test procedures and standards. 51.357... Requirements § 51.357 Test procedures and standards. Written test procedures and pass/fail standards shall be established and followed for each model year and vehicle type included in the program. (a) Test procedure...

An IMU-to-Body Alignment Method Applied to Human Gait Analysis

PubMed Central

Vargas-Valencia, Laura Susana; Elias, Arlindo; Rocon, Eduardo; Bastos-Filho, Teodiano; Frizera, Anselmo

2016-01-01

This paper presents a novel calibration procedure as a simple, yet powerful, method to place and align inertial sensors with body segments. The calibration can be easily replicated without the need of any additional tools. The proposed method is validated in three different applications: a computer mathematical simulation; a simplified joint composed of two semi-spheres interconnected by a universal goniometer; and a real gait test with five able-bodied subjects. Simulation results demonstrate that, after the calibration method is applied, the joint angles are correctly measured independently of previous sensor placement on the joint, thus validating the proposed procedure. In the cases of a simplified joint and a real gait test with human volunteers, the method also performs correctly, although secondary plane errors appear when compared with the simulation results. We believe that such errors are caused by limitations of the current inertial measurement unit (IMU) technology and fusion algorithms. In conclusion, the presented calibration procedure is an interesting option to solve the alignment problem when using IMUs for gait analysis. PMID:27973406

Verification System: First System-Wide Performance Test

NASA Astrophysics Data System (ADS)

Chernobay, I.; Zerbo, L.

2006-05-01

System-wide performance tests are essential for the development, testing and evaluation of individual components of the verification system. In addition to evaluating global readiness it helps establishing the practical and financial requirements for eventual operations. The first system-wide performance test (SPT1) was conducted in three phases: - A preparatory phase in May-June 2004 - A performance testing phase in April-June 2005 - An evaluation phase in the last half of 2005. The preparatory phase was developmental in nature. The main objectives for the performance testing phase included establishment of performance baseline under current provisional mode of operation (CTBT/PC- 19/1/Annex II, CTBT/WGB-21/1), examination of established requirements and procedures for operation and maintenance. To establish a system-wide performance baseline the system configuration was fixed for April-May 2005. The third month (June 2005) was used for implementation of 21 test case scenarios to examine either particular operational procedures or the response of the system components to the failures simulated under controlled conditions. A total of 163 stations and 5 certified radionuclide laboratories of International Monitoring System (IMS) participated in the performance testing phase - about 50% of the eventual IMS network. 156 IMS facilities and 40 National Data Centres (NDCs) were connected to the International Data Centre (IDC) via Global Communication Infrastructure (GCI) communication links. In addition, 12 legacy stations in the auxiliary seismic network sent data to the IDC over the Internet. During the performance testing phase, the IDC produced all required products, analysed more than 6100 seismic events and 1700 radionuclide spectra. Performance of all system elements was documented and analysed. IDC products were compared with results of data processing at the NDCs. On the basis of statistics and information collected during the SPT1 a system-wide performance baseline under current guidelines for provisional Operation and Maintenance was established. The test provided feedback for further development of the draft IMS and IDC Operational Manuals and identified priority areas for further system development.

A Novel Method for In Situ Electromechanical Characterization of Nanoscale Specimens

PubMed Central

Reid, Russell C.; Piqué, Alberto; Kang, Wonmo

2017-01-01

Electrically assisted deformation (EAD) is increasingly being used to improve the formability of metals during processes such as sheet metal rolling and forging. Adoption of this technique is proceeding despite disagreement concerning the underlying mechanism responsible for EAD. The experimental procedure described herein enables a more explicit study compared to previous EAD research by removing thermal effects, which are responsible for disagreement in interpreting previous EAD results. Furthermore, as the procedure described here enables EAD observation in situ and in real time in a transmission electron microscope (TEM), it is superior to existing post-mortem methods that observe EAD effects post-test. Test samples consist of a single crystal copper (SCC) foil having a free-standing tensile test section of nanoscale thickness, fabricated using a combination of laser and ion beam milling. The SCC is mounted to an etched silicon base that provides mechanical support and electrical isolation while serving as a heat sink. Using this geometry, even at high current density (~3,500 A/mm2), the test section experiences a negligible temperature increase (<0.02 °C), thus eliminating Joule heating effects. Monitoring material deformation and identifying the corresponding changes to microstructures, e.g. dislocations, are accomplished by acquiring and analyzing a series of TEM images. Our sample preparation and in situ experiment procedures are robust and versatile as they can be readily utilized to test materials with different microstructures, e.g., single and polycrystalline copper. PMID:28605394

Bon-EV: an improved multiple testing procedure for controlling false discovery rates.

PubMed

Li, Dongmei; Xie, Zidian; Zand, Martin; Fogg, Thomas; Dye, Timothy

2017-01-03

Stability of multiple testing procedures, defined as the standard deviation of total number of discoveries, can be used as an indicator of variability of multiple testing procedures. Improving stability of multiple testing procedures can help to increase the consistency of findings from replicated experiments. Benjamini-Hochberg's and Storey's q-value procedures are two commonly used multiple testing procedures for controlling false discoveries in genomic studies. Storey's q-value procedure has higher power and lower stability than Benjamini-Hochberg's procedure. To improve upon the stability of Storey's q-value procedure and maintain its high power in genomic data analysis, we propose a new multiple testing procedure, named Bon-EV, to control false discovery rate (FDR) based on Bonferroni's approach. Simulation studies show that our proposed Bon-EV procedure can maintain the high power of the Storey's q-value procedure and also result in better FDR control and higher stability than Storey's q-value procedure for samples of large size(30 in each group) and medium size (15 in each group) for either independent, somewhat correlated, or highly correlated test statistics. When sample size is small (5 in each group), our proposed Bon-EV procedure has performance between the Benjamini-Hochberg procedure and the Storey's q-value procedure. Examples using RNA-Seq data show that the Bon-EV procedure has higher stability than the Storey's q-value procedure while maintaining equivalent power, and higher power than the Benjamini-Hochberg's procedure. For medium or large sample sizes, the Bon-EV procedure has improved FDR control and stability compared with the Storey's q-value procedure and improved power compared with the Benjamini-Hochberg procedure. The Bon-EV multiple testing procedure is available as the BonEV package in R for download at https://CRAN.R-project.org/package=BonEV .

Petition to request an exemption from 100 percent identity testing of dietary ingredients: Current Good Manufacturing Practice in Manufacturing, Packaging, Labeling, or Holding Operations for Dietary Supplements. Interim final rule.

PubMed

2007-06-25

The Food and Drug Administration (FDA) is issuing an interim final rule (IFR) that sets forth a procedure for requesting an exemption from the requirement in the final rule "Current Good Manufacturing Practice in Manufacturing, Packaging, Labeling, or Holding Operations for Dietary Supplements," published elsewhere in this issue of the Federal Register, that the manufacturer conduct at least one appropriate test or examination to verify the identity of any component that is a dietary ingredient. This IFR allows for submission to, and review by, FDA of an alternative to the required 100 percent identity testing of components that are dietary ingredients, provided certain conditions are met and establishes a requirement for retention of records relating to the FDA's response to an exemption request.

Calibration procedures for imaging spectrometers: improving data quality from satellite missions to UAV campaigns

NASA Astrophysics Data System (ADS)

Brachmann, Johannes F. S.; Baumgartner, Andreas; Lenhard, Karim

2016-10-01

The Calibration Home Base (CHB) at the Remote Sensing Technology Institute of the German Aerospace Center (DLR-IMF) is an optical laboratory designed for the calibration of imaging spectrometers for the VNIR/SWIR wavelength range. Radiometric, spectral and geometric characterization is realized in the CHB in a precise and highly automated fashion. This allows performing a wide range of time consuming measurements in an efficient way. The implementation of ISO 9001 standards ensures a traceable quality of results. DLR-IMF will support the calibration and characterization campaign of the future German spaceborne hyperspectral imager EnMAP. In the context of this activity, a procedure for the correction of imaging artifacts, such as due to stray light, is currently being developed by DLR-IMF. Goal is the correction of in-band stray light as well as ghost images down to a level of a few digital numbers in the whole wavelength range 420-2450 nm. DLR-IMF owns a Norsk Elektro Optikks HySpex airborne imaging spectrometer system that has been thoroughly characterized. This system will be used to test stray light calibration procedures for EnMAP. Hyperspectral snapshot sensors offer the possibility to simultaneously acquire hyperspectral data in two dimensions. Recently, these rather new spectrometers have arisen much interest in the remote sensing community. Different designs are currently used for local area observation such as by use of small unmanned aerial vehicles (sUAV). In this context the CHB's measurement capabilities are currently extended such that a standard measurement procedure for these new sensors will be implemented.

Processes of conscious and unconscious memory: evidence from current research on dissociation of memories within a test.

PubMed

Cheng, Chao-Ming; Huang, Chin-Lan

2011-01-01

The processes of conscious memory (CM) and unconscious memory (UM) are explored, based on the results of the current and previous studies in which the 2 forms of memory within a test were separated by either the process dissociation or metacognition-based dissociation procedure. The results assessing influences of shallow and deep processing, association, and self-generation on CM in explicit and implicit tests are taken as evidence that CM in a test is driven not only conceptually but also by the driving nature of the test, and CM benefits from an encoding condition to the extent that information processing for CM recapitulates that engaged in the encoding condition.Those influences on UM in explicit and implicit tests are taken to support the view that UM in a test is driven by the nature of the test itself, and UM benefits from an encoding condition to the extent that the cognitive environments at test and at study match to activate the same type of information (e.g., visual, lexical, or semantic) about memory items or the same content of a preexisting association or categorical structure.

The most common mistakes on dermatoscopy of melanocytic lesions

PubMed Central

Kamińska-Winciorek, Grażyna

2015-01-01

Dermatoscopy is a method of in vivo evaluation of the structures within the epidermis and dermis. Currently, it may be the most precise pre-surgical method of diagnosing melanocytic lesions. Diagnostic errors may result in unnecessary removal of benign lesions or what is even worse, they can cause early and very early melanomas to be overlooked. Errors in assessment of dermatoscopy can be divided into those arising from failure to maintain proper test procedures (procedural and technical errors) and knowledge based mistakes related to the lack of sufficient familiarity and experience in dermatoscopy. The article discusses the most common mistakes made by beginner or inexperienced dermatoscopists. PMID:25821425

Tube cutter tool and method of use for coupon removal

DOEpatents

Nachbar, H.D.; Etten, M.P. Jr.; Kurowski, P.A.

1997-05-06

A tube cutter tool is insertable into a tube for cutting a coupon from a damaged site on the exterior of the tube. Prior to using the tool, the damaged site is first located from the interior of the tube using a multi-coil pancake eddy current test probe. The damaged site is then marked. A fiber optic probe is used to monitor the subsequent cutting procedure which is performed using a hole saw mounted on the tube cutter tool. Prior to completion of the cutting procedure, a drill in the center of the hole saw is drilled into the coupon to hold it in place. 4 figs.

Tube cutter tool and method of use for coupon removal

DOEpatents

Nachbar, Henry D.; Etten, Jr., Marvin P.; Kurowski, Paul A.

1997-01-01

A tube cutter tool is insertable into a tube for cutting a coupon from a damaged site on the exterior of the tube. Prior to using the tool, the damaged site is first located from the interior of the tube using a multi-coil pancake eddy current test probe. The damaged site is then marked. A fiber optic probe is used to monitor the subsequent cutting procedure which is performed using a hole saw mounted on the tube cutter tool. Prior to completion of the cutting procedure, a drill in the center of the hole saw is drilled into the coupon to hold it in place.

Some comments upon current optical shop practices.

PubMed

Larmer, J W; Goldstein, E

1966-05-01

The fabrication of optical elements began as an art rather than a science and has tended to remain so throughout its history. Today's methods are largely extensions of the original techniques. With spaceage demands for rapid response as well as quality, some effort is being made to remove optical technology from the realm of wizardry by standardizing fabrication procedures and associated working materials. However, the diversity of problems encountered in modern optical fabrication requires a flexibility of approach which indicates that the artisan will always be with us. Examples of some optical fabrication and testing procedures employed at the Goddard Space Flight Center are presented.

SWI 1.10 Testing Process

NASA Technical Reports Server (NTRS)

Stokes, LeBarian

2009-01-01

This procedure establishes a system for performing testing in the Six-Degree-Of-Freedom Dynamic Test System (SDTS). Testing includes development and verification testing of customer supplied Test Articles (TAs) and other testing requirements, as requested. This procedure applies to all SDTS testing operations and equipment. The procedure provides an overview of testing performed in the SDTS including test identification requirements, test planning and procedure development, test and performance inspection, test data analysis, and test report generation.

Motor current signature analysis for gearbox condition monitoring under transient speeds using wavelet analysis and dual-level time synchronous averaging

NASA Astrophysics Data System (ADS)

Bravo-Imaz, Inaki; Davari Ardakani, Hossein; Liu, Zongchang; García-Arribas, Alfredo; Arnaiz, Aitor; Lee, Jay

2017-09-01

This paper focuses on analyzing motor current signature for fault diagnosis of gearboxes operating under transient speed regimes. Two different strategies are evaluated, extensively tested and compared to analyze the motor current signature in order to implement a condition monitoring system for gearboxes in industrial machinery. A specially designed test bench is used, thoroughly monitored to fully characterize the experiments, in which gears in different health status are tested. The measured signals are analyzed using discrete wavelet decomposition, in different decomposition levels using a range of mother wavelets. Moreover, a dual-level time synchronous averaging analysis is performed on the same signal to compare the performance of the two methods. From both analyses, the relevant features of the signals are extracted and cataloged using a self-organizing map, which allows for an easy detection and classification of the diverse health states of the gears. The results demonstrate the effectiveness of both methods for diagnosing gearbox faults. A slightly better performance was observed for dual-level time synchronous averaging method. Based on the obtained results, the proposed methods can used as effective and reliable condition monitoring procedures for gearbox condition monitoring using only motor current signature.

Free-Operant Avoidance Behavior by Rats after Reinforcer Revaluation Using Opioid Agonists and d-Amphetamine

PubMed Central

Urcelay, Gonzalo; Mar, Adam; Dickinson, Anthony; Robbins, Trevor

2014-01-01

The associative processes that support free-operant instrumental avoidance behavior are still unknown. We used a revaluation procedure to determine whether the performance of an avoidance response is sensitive to the current value of the aversive, negative reinforcer. Rats were trained on an unsignaled, free-operant lever press avoidance paradigm in which each response avoided or escaped shock and produced a 5 s feedback stimulus. The revaluation procedure consisted of noncontingent presentations of the shock in the absence of the lever either paired or unpaired with systemic morphine and in a different cohort with systemic d-amphetamine. Rats were then tested drug free during an extinction test. In both the d-amphetamine and morphine groups, pairing of the drug and shock decreased subsequent avoidance responding during the extinction test, suggesting that avoidance behavior was sensitive to the current incentive value of the aversive negative reinforcer. Experiment 2 used central infusions of D-Ala2, NMe-Phe4, Gly-ol5]-enkephalin (DAMGO), a mu-opioid receptor agonist, in the periacqueductal gray and nucleus accumbens shell to revalue the shock. Infusions of DAMGO in both regions replicated the effects seen with systemic morphine. These results are the first to demonstrate the impact of revaluation of an aversive reinforcer on avoidance behavior using pharmacological agents, thereby providing potential therapeutic targets for the treatment of avoidance behavior symptomatic of anxiety disorders. PMID:24790199

Biopsy Procedures and Molecular Testing Utilization and Related Costs in Patients with Metastatic Lung Cancer.

PubMed

Shinde, Reshma; Cao, Xiting; Kothari, Smita

2016-10-01

Epidermal growth factor receptor (EGFR) gene mutations and anaplastic lymphoma kinase (ALK) gene rearrangements are key therapeutic targets for biomarker-driven treatment with an EGFR or ALK tyrosine kinase inhibitor (TKI) in patients with metastatic non-small cell lung cancer (NSCLC). To appropriately guide treatment decisions, since 2011, the National Comprehensive Cancer Network and the American Society of Clinical Oncology therefore recommend EGFR and ALK analysis in tumor samples obtained at the time of diagnosis in patients with non-squamous NSCLC. Currently, there are limited data on utilization patterns and cost of biopsy procedures and biomarker tests in patients with metastatic NSCLC who receive an EGFR or ALK TKI. To (a) describe utilization patterns and costs associated with biopsy procedures and biomarker testing in patients with NSCLC who received erlotinib or crizotinib between 2009 and 2012 and (b) investigate the timing of these procedures relative to the erlotinib or crizotinib index date. Adult patients with metastatic lung cancer were identified by ICD-9-CM diagnostic codes within the Truven Health Analytic MarketScan database. Patients were included in the analysis if they had an index erlotinib or crizotinib claim between January 1, 2009, and September 30, 2012 (index period) and were continuously enrolled for ≥ 12 months before the index claim. Because there is no specific ICD-9-CM diagnostic code for NSCLC, patients with metastatic lung cancer who received erlotinib or crizotinib were considered to have metastatic NSCLC. Using CPT and ICD-9-CM codes, lung biopsy procedures performed during the 24 months before or 12 months after the index claim date were identified. For every patient, biomarker testing claims for EGFR and ALK were identified using the molecular pathology stacked CPT code during the 2 months before or 1 month after the index date. The frequency of claims for biopsy procedures and biomarker testing was analyzed descriptively. The overall summary measures for biomarker testing, especially frequency of EGFR testing in patients receiving erlotinib, was also described as before and after 2011, the year when biomarker testing became part of the guidelines. Per patient and overall costs for biopsy procedures and biomarker testing were calculated from payer and patient perspectives. Of the 4,926 identified patients, 4,801 (97.5%) received erlotinib, and 125 (2.5%) received crizotinib. Biopsy procedure claims were identified for 3,579 (72.7%) patients, including 3,503 (73.0%) erlotinib recipients and 76 (60.8%) crizotinib recipients. Biomarker testing claims were identified for 675 (13.7%) patients, including 634 (13.2%) erlotinib recipients and 41 (32.8%) crizotinib recipients. Overall, most biomarker testing procedures (476 of 741) were identified in 435 (of 675) patients after year 2011. Also, among erlotinib recipients, percentage of patients receiving EGFR testing was increased over the index period. Per patient mean (SD) numbers of biopsy procedures and biomarker tests were 1.2 (1.1) and 0.2 (0.4), respectively. In the outpatient setting, per patient mean (SD) cost per biopsy procedure was $1,223 ($1,899) from the payer perspective and $60 ($147) from the patient perspective, whereas in the inpatient setting, it was $8,163 ($18,712) and $180 ($691), respectively. Among patients receiving at least 1 biomarker test, the per patient mean (SD) cost for the overall population was $891 ($1,062) and $43 ($229); for erlotinib recipients, it was $906 ($1,084) and $42 ($228); and for crizotinib recipients, it was $664 ($576) and $55 ($243) in payer and patient perspectives, respectively. This study provides insight into the use and cost of biopsy and biomarker testing procedures in patients with metastatic NSCLC. The low frequency of biomarker testing highlights the need for more awareness of testing to guide treatment decisions in these patients. Costs associated with biopsy procedures and biomarker testing provide insight into the economic impact on metastatic NSCLC patients treated with targeted therapy. This study was sponsored by Merck & Co. Shinde is a study manager working for Merck under contract with AllSourcePPS, an Agile 1 company in Huntington Beach, California. Cao and Kothari are employees of Merck & Co., Kenilworth, New Jersey. Study concept and design were contributed primarily by Shinde and Kothari. Data analysis was performed by Cao. Data interpretation was performed by Shinde, Cao, and Kothari. Shinde wrote the manuscript with assistance from Cao and Kothari. The revision was completed primarily by Shinde and Kothari.

75 FR 47817 - Notice of Availability: Test Tools and Test Procedures Approved for the Office of the National...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-09

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Notice of Availability: Test Tools and Test Procedures.... SUMMARY: This notice announces the availability of test tools and test procedures approved by the National... certification program. The approved test tools and test procedures are identified on the ONC Web site at: http...

77 FR 64343 - Notice of Availability: Test Tools and Test Procedures Approved for the Office of the National...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-19

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Notice of Availability: Test Tools and Test Procedures.... SUMMARY: This notice announces the availability of test tools and test procedures approved by the National... test tools and test procedures are identified on the ONC Web site at: http://www.healthit.gov/policy...

A new experimental procedure of outgassing rate measurement to obtain more precise deposition properties of materials

NASA Astrophysics Data System (ADS)

Miyazaki, Eiji; Shimazaki, Kazunori; Numata, Osamu; Waki, Miyuki; Yamanaka, Riyo; Kimoto, Yugo

2016-09-01

Outgassing rate measurement, or dynamic outgassing test, is used to obtain outgassing properties of materials, i.e., Total Mass Loss, "TML," and Collected Volatile Condensed Mass, "CVCM." The properties are used as input parameters for executing contamination analysis, e.g., calculating a prediction of deposition mass on a surface in a spacecraft caused by outgassed substances from contaminant sources onboard. It is likely that results obtained by such calculations are affected by the input parameters. Thus, it is important to get a sufficient experimental data set of outgassing rate measurements for extract good outgassing parameters of materials for calculation. As specified in the standard, ASTM E 1559, TML is measured by a QCM sensor kept at cryogenic temperature; CVCMs are measured at certain temperatures. In the present work, the authors propose a new experimental procedure to obtain more precise VCMs from one run of the current test time with the present equipment. That is, two of four CQCMs in the equipment control the temperature to cool step-by-step during the test run. It is expected that the deposition rate, that is sticking coefficient, with respect to temperature could be discovered. As a result, the sticking coefficient can be obtained directly between -50 and 50 degrees C with 5 degrees C step. It looks like the method could be used as an improved procedure for outgassing rate measurement. The present experiment also specified some issues of the new procedure. It will be considered in future work.

Preschooler test or procedure preparation

MedlinePlus

Preparing preschoolers for test/procedure; Test/procedure preparation - preschooler ... Preparing children for medical tests can reduce their anxiety. It can also make them less likely to cry and resist the procedure. Research shows that ...

77 FR 4203 - Energy Conservation Program: Test Procedures for General Service Fluorescent Lamps, General...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-27

...On September 14, 2011, the U.S. Department of Energy (DOE) issued a notice of proposed rulemaking (NOPR) to amend the test procedures for general service fluorescent lamps (GSFLs), general service incandescent lamps (GSILs), and incandescent reflector lamps (IRLs). That proposed rulemaking serves as the basis for today's action. DOE is amending its test procedures for GSFLs and GSILs established under the Energy Policy and Conservation Act (EPCA). DOE is not amending in this final rule the existing test procedure for IRLs established under EPCA. For GSFLs and GSILs, DOE is updating several references to the industry standards referenced in DOE's test procedures. DOE is also establishing a lamp lifetime test procedure for GSILs. These test procedures also provide the protocols upon which the Federal Trade Commission bases its energy guide label for these products. DOE's review of the GSFL, GSIL, and IRL test procedures fulfills the EPCA requirement that DOE review test procedures for all covered products at least once every seven years.

Test Operations Procedure (TOP) 03-2-827 Test Procedures for Video Target Scoring Using Calibration Lights

DTIC Science & Technology

2016-04-04

Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 03-2-827 Test Procedures for Video Target Scoring Using...ABSTRACT This Test Operations Procedure (TOP) describes typical equipment and procedures to setup and operate a Video Target Scoring System (VTSS) to...lights. 15. SUBJECT TERMS Video Target Scoring System, VTSS, witness screens, camera, target screen, light pole 16. SECURITY

A new instrument to assess physician skill at thoracic ultrasound, including pleural effusion markup.

PubMed

Salamonsen, Matthew; McGrath, David; Steiler, Geoff; Ware, Robert; Colt, Henri; Fielding, David

2013-09-01

To reduce complications and increase success, thoracic ultrasound is recommended to guide all chest drainage procedures. Despite this, no tools currently exist to assess proceduralist training or competence. This study aims to validate an instrument to assess physician skill at performing thoracic ultrasound, including effusion markup, and examine its validity. We developed an 11-domain, 100-point assessment sheet in line with British Thoracic Society guidelines: the Ultrasound-Guided Thoracentesis Skills and Tasks Assessment Test (UGSTAT). The test was used to assess 22 participants (eight novices, seven intermediates, seven advanced) on two occasions while performing thoracic ultrasound on a pleural effusion phantom. Each test was scored by two blinded expert examiners. Validity was examined by assessing the ability of the test to stratify participants according to expected skill level (analysis of variance) and demonstrating test-retest and intertester reproducibility by comparison of repeated scores (mean difference [95% CI] and paired t test) and the intraclass correlation coefficient. Mean scores for the novice, intermediate, and advanced groups were 49.3, 73.0, and 91.5 respectively, which were all significantly different (P < .0001). There were no significant differences between repeated scores. Procedural training on mannequins prior to unsupervised performance on patients is rapidly becoming the standard in medical education. This study has validated the UGSTAT, which can now be used to determine the adequacy of thoracic ultrasound training prior to clinical practice. It is likely that its role could be extended to live patients, providing a way to document ongoing procedural competence.

Hypothesis test of mediation effect in causal mediation model with high-dimensional continuous mediators.

PubMed

Huang, Yen-Tsung; Pan, Wen-Chi

2016-06-01

Causal mediation modeling has become a popular approach for studying the effect of an exposure on an outcome through a mediator. However, current methods are not applicable to the setting with a large number of mediators. We propose a testing procedure for mediation effects of high-dimensional continuous mediators. We characterize the marginal mediation effect, the multivariate component-wise mediation effects, and the L2 norm of the component-wise effects, and develop a Monte-Carlo procedure for evaluating their statistical significance. To accommodate the setting with a large number of mediators and a small sample size, we further propose a transformation model using the spectral decomposition. Under the transformation model, mediation effects can be estimated using a series of regression models with a univariate transformed mediator, and examined by our proposed testing procedure. Extensive simulation studies are conducted to assess the performance of our methods for continuous and dichotomous outcomes. We apply the methods to analyze genomic data investigating the effect of microRNA miR-223 on a dichotomous survival status of patients with glioblastoma multiforme (GBM). We identify nine gene ontology sets with expression values that significantly mediate the effect of miR-223 on GBM survival. © 2015, The International Biometric Society.

The effects of mild and severe traumatic brain injury on speed of information processing as measured by the computerized tests of information processing (CTIP).

PubMed

Tombaugh, Tom N; Rees, Laura; Stormer, Peter; Harrison, Allyson G; Smith, Andra

2007-01-01

In spite of the fact that reaction time (RT) measures are sensitive to the effects of traumatic brain injury (TBI), few RT procedures have been developed for use in standard clinical evaluations. The computerized test of information processing (CTIP) [Tombaugh, T. N., & Rees, L. (2000). Manual for the computerized tests of information processing (CTIP). Ottawa, Ont.: Carleton University] was designed to measure the degree to which TBI decreases the speed at which information is processed. The CTIP consists of three computerized programs that progressively increase the amount of information that is processed. Results of the current study demonstrated that RT increased as the difficulty of the CTIP tests increased (known as the complexity effect), and as severity of injury increased (from mild to severe TBI). The current study also demonstrated the importance of selecting a non-biased measure of variability. Overall, findings suggest that the CTIP is an easy to administer and sensitive measure of information processing speed.

Detection of fatigue cracks by nondestructive testing methods

NASA Technical Reports Server (NTRS)

Anderson, R. T.; Delacy, T. J.; Stewart, R. C.

1973-01-01

The effectiveness was assessed of various NDT methods to detect small tight cracks by randomly introducing fatigue cracks into aluminum sheets. The study included optimizing NDT methods calibrating NDT equipment with fatigue cracked standards, and evaluating a number of cracked specimens by the optimized NDT methods. The evaluations were conducted by highly trained personnel, provided with detailed procedures, in order to minimize the effects of human variability. These personnel performed the NDT on the test specimens without knowledge of the flaw locations and reported on the flaws detected. The performance of these tests was measured by comparing the flaws detected against the flaws present. The principal NDT methods utilized were radiographic, ultrasonic, penetrant, and eddy current. Holographic interferometry, acoustic emission monitoring, and replication methods were also applied on a reduced number of specimens. Generally, the best performance was shown by eddy current, ultrasonic, penetrant and holographic tests. Etching provided no measurable improvement, while proof loading improved flaw detectability. Data are shown that quantify the performances of the NDT methods applied.

Development and verification testing of automation and robotics for assembly of space structures

NASA Technical Reports Server (NTRS)

Rhodes, Marvin D.; Will, Ralph W.; Quach, Cuong C.

1993-01-01

A program was initiated within the past several years to develop operational procedures for automated assembly of truss structures suitable for large-aperture antennas. The assembly operations require the use of a robotic manipulator and are based on the principle of supervised autonomy to minimize crew resources. A hardware testbed was established to support development and evaluation testing. A brute-force automation approach was used to develop the baseline assembly hardware and software techniques. As the system matured and an operation was proven, upgrades were incorprated and assessed against the baseline test results. This paper summarizes the developmental phases of the program, the results of several assembly tests, the current status, and a series of proposed developments for additional hardware and software control capability. No problems that would preclude automated in-space assembly of truss structures have been encountered. The current system was developed at a breadboard level and continued development at an enhanced level is warranted.

40 CFR 92.506 - Test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Test procedures. 92.506 Section 92.506... and Audit Programs § 92.506 Test procedures. (a)(1) For locomotives and locomotive engines subject to the provisions of this subpart, the prescribed test procedures are those procedures described in...

Fuel-Flexible Engines for Portable-Power Applications

DTIC Science & Technology

2009-05-31

military grade, JP8, respectively. Repeated testing procedures elucidated the need for better measurement and control of the glow plug intensity ...different fuels that are currently available for market consumption. While petroleum- based fuels are being tested in this research, the researchers are...0.8 210 15 TA4, TA7 Gasoline C8-H18 0.75 280 15.1 TA7 Light Diesel C8-H18 0.85 210 15 TA7 Medium Diesel C14-H30 0.85 210 15 TA7 Heavy Diesel C21-H44

Application of physical parameter identification to finite-element models

NASA Technical Reports Server (NTRS)

Bronowicki, Allen J.; Lukich, Michael S.; Kuritz, Steven P.

1987-01-01

The time domain parameter identification method described previously is applied to TRW's Large Space Structure Truss Experiment. Only control sensors and actuators are employed in the test procedure. The fit of the linear structural model to the test data is improved by more than an order of magnitude using a physically reasonable parameter set. The electro-magnetic control actuators are found to contribute significant damping due to a combination of eddy current and back electro-motive force (EMF) effects. Uncertainties in both estimated physical parameters and modal behavior variables are given.

Mental rotation - A key to mitigation of motion sickness in the virtual environments?

NASA Technical Reports Server (NTRS)

Parker, Donald E.; Harm, Deborah L.

1992-01-01

If mental rotation is important for the reduction of motion sickness and complement performance in virtual environments (VEs), the use of the Howard (1982) mental rotation test battery may identify individuals with lower susceptibility to VE-induced motion sickness and therefore a greater probability of success as VE operators. An apparatus and its associated procedures are currently under development for astronaut microgravity training aimed at reducing motion sickness; it is hypothesized that this system may be of significance to VE testing and training.

Baseline experimental investigation of an electrohydrodynamically assisted heat pipe

NASA Technical Reports Server (NTRS)

Duncan, A. B.

1995-01-01

The increases in power demand and associated thermal management requirements of future space programs such as potential Lunar/Mars missions will require enhancing the operating efficiencies of thermal management devices. Currently, the use of electrohydrodynamically (EHD) assisted thermal control devices is under consideration as a potential method of increasing thermal management system capacity. The objectives of the currently described investigation included completing build-up of the EHD-Assisted Heat Pipe Test bed, developing test procedures for an experimental evaluation of the unassisted heat pipe, developing an analytical model capable of predicting the performance limits of the unassisted heat pipe, and obtaining experimental data which would define the performance characteristics of the unassisted heat pipe. The information obtained in the currently proposed study will be used in order to provide extensive comparisons with the EHD-assisted performance observations to be obtained during the continuing investigation of EHD-Assisted heat transfer devices. Through comparisons of the baseline test bed data and the EHD assisted test bed data, accurate insight into the performance enhancing characteristics of EHD augmentation may be obtained. This may lead to optimization, development, and implementation of EHD technology for future space programs.

Improving the Sandia Test Protocols with Advanced Inverter Functionality Testing of INV3, VV11, FW21, and L/HVRT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Jay Dean

2013-11-01

Sandia National Laboratories has created a test protocol for IEC TR 61850-90-7 advanced distributed energy resource (DER) functions, titled "Test Protocols for Advanced Inverter Interoperability Functions," often referred to as the Sandia Test Protocols. This document is currently in draft form, but has been shared with stakeholders around the world with the ultimate goal of collaborating to create a consensus set of test protocols which can be then incorporated into an International Electrotechnical Commission (IEC) and/or Underwriters Laboratories (UL) certification standard. The protocols are designed to ensure functional interoperability of DER (primarily photovoltaic (PV) inverters and energy storage systems) asmore » specified by the IEC technical report through communication and electrical tests. In this report, Sandia exercises the electrical characterization portion of the test protocols for four functions: constant power factor (INV3), volt-var (VV11), frequency-watt (FW21), and Low and High Voltage Ride Through (L/HVRT). The goal of the tests reported here was not to characterize the performance of the equipment under test (EUT), but rather to (a) exercise the draft Sandia Test Protocols in order to identify any revisions needed in test procedures, conditions, or equipment and (b) gain experience with state-of-the-art DER equipment to determine if the tests put unrealistic or overly aggressive requirements on EUT operation. In performing the work according to the current versions of the protocols, Sandia was able to identify weaknesses in the current versions and suggest improvements to the test protocols.« less

Procedural justice in children: Preschoolers accept unequal resource distributions if the procedure provides equal opportunities.

PubMed

Grocke, Patricia; Rossano, Federico; Tomasello, Michael

2015-12-01

When it is not possible to distribute resources equitably to everyone, people look for an equitable or just procedure. In the current study, we investigated young children's sense of procedural justice. We tested 32 triads of 5-year-olds in a new resource allocation game. Triads were confronted with three unequal reward packages and then agreed on a procedure to allocate them among themselves. To allocate the rewards, they needed to use a "wheel of fortune." Half of the groups played with a fair wheel (where each child had an equal chance of obtaining each reward package), and the other half played with an unfair wheel. We analyzed children's interactions when using the wheel and conducted an interview with each child after the game was over. Children using the unfair wheel often decided to change the rules of the game, and they also rated it as an unfair procedure in the interview. In contrast, children who played with the fair wheel were mostly accepting of both the outcome and the procedure. Overall, we found that children as young as preschool age are already sensitive not only to distributive justice but to procedural justice as well. Copyright © 2015 Elsevier Inc. All rights reserved.

Impact Testing of a Stirling Converter's Linear Alternator

NASA Technical Reports Server (NTRS)

Suarez, Vicente J.; Goodnight, Thomas W.; Hughes, William O.; Samorezov, Sergey

2002-01-01

The U.S. Department of Energy (DOE), in conjunction with the NASA John H. Glenn Research Center and Stirling Technology Company, are currently developing a Stirling convertor for a Stirling Radioisotope Generator (SRG). NASA Headquarters and DOE have identified the SRG for potential use as an advanced spacecraft power system for future NASA deep-space and Mars surface missions. Low-level dynamic impact tests were conducted at NASA Glenn Research Center's Structural Dynamics Laboratory as part of the development of this technology. The purpose of this test was to identify dynamic structural characteristics of the Stirling Technology Demonstration Convertor (TDC). This paper addresses the test setup, procedure, and results of the impact testing conducted on the Stirling TDC in May 2001.

Impact testing of a Stirling convertor's linear alternator

NASA Astrophysics Data System (ADS)

Suárez, Vicente J.; Goodnight, Thomas W.; Hughes, William O.; Samorezov, Sergey

2002-01-01

The U.S. Department of Energy (DOE), in conjunction with NASA John H. Glenn Research Center and Stirling Technology Company, are currently developing a Stirling convertor for a Stirling Radioisotope Generator (SRG). NASA Headquarters and DOE have identified the SRG for potential use as an advanced spacecraft power system for future NASA deep-space and Mars surface missions. Low-level dynamic impact tests were conducted at NASA Glenn Research Center's Structural Dynamics Laboratory as part of the development of this technology. The purpose of this test was to identify dynamic structural characteristics of the Stirling Technology Demonstration Convertor (TDC). This paper addresses the test setup, procedure and results of the impact testing conducted on the Stirling TDC in May 2001. .

40 CFR 92.125 - Pre-test procedures and preconditioning.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Pre-test procedures and... PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.125 Pre-test procedures and preconditioning. (a) Locomotive testing. (1) Determine engine lubricating...

40 CFR 92.125 - Pre-test procedures and preconditioning.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Pre-test procedures and... PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.125 Pre-test procedures and preconditioning. (a) Locomotive testing. (1) Determine engine lubricating...

40 CFR 92.125 - Pre-test procedures and preconditioning.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Pre-test procedures and... PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.125 Pre-test procedures and preconditioning. (a) Locomotive testing. (1) Determine engine lubricating...

40 CFR 92.125 - Pre-test procedures and preconditioning.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Pre-test procedures and... PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.125 Pre-test procedures and preconditioning. (a) Locomotive testing. (1) Determine engine lubricating...

Current Performance Characteristics of NASA Langley Research Center's Cockpit Motion Base and Standardized Test Procedure for Future Performance Characterization

NASA Technical Reports Server (NTRS)

Cowen, Brandon; Stringer, Mary T.; Hutchinson, Brian K.; Davidson, Paul C.; Gupton, Lawrence E.

2014-01-01

This report documents the updated performance characteristics of NASA Langley Research Center's (LaRC) Cockpit Motion Base (CMB) after recent revisions that were made to its inner-loop, feedback control law. The modifications to the control law will be briefly described. The performance of the Cockpit Motion Facility (CMF) will be presented. A short graphical comparison to the previous control law can be found in the appendix of this report. The revised controller will be shown to yield reduced parasitic accelerations with respect to the previous controller. Metrics based on the AGARD Advisory Report No. 144 are used to assess the overall system performance due to its recent control algorithm modification. This report also documents the standardized simulator test procedure which can be used in the future to evaluate potential updates to the control law.

NASA's Beachside Corrosion Test Site and Current Environmentally Friendly Corrosion Control Initiatives

NASA Technical Reports Server (NTRS)

Russell, Richard W.; Calle, Luz Marina; Johnston, Frederick; Montgomery, Eliza L.; Curran, Jerome P.; Kolody, Mark R.

2013-01-01

NASA began corrosion studies at the Kennedy Space Center (KSC) in 1966 during the Gemini/Apollo Programs with the evaluation of long-term corrosion protective coatings for carbon steel. KSC's Beachside Corrosion Test Site (BCTS), which has been documented by the American Society of Materials (ASM) as one of the most corrosive, naturally occurring, environments in the world, was established at that time. With the introduction of the Space Shuttle in 1981, the already highly corrosive conditions at the launch pad were rendered even more severe by the acid ic exhaust from the solid rocket boosters. In the years that followed, numerous studies have identified materials, coatings, and maintenance procedures for launch hardware and equipment exposed to the highly corrosive environment at the launch pad. This paper presents a historical overview of over 45 years of corrosion and coating evaluation studies and a description of the BCTS's current capabilities. Additionally, current research and testing programs involving chromium free coatings, environmentally friendly corrosion preventative compounds, and alternates to nitric acid passivation will be discussed.

16 CFR 1610.6 - Test procedure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Test procedure. 1610.6 Section 1610.6... FLAMMABILITY OF CLOTHING TEXTILES The Standard § 1610.6 Test procedure. The test procedure is divided into two... according to paragraph (b)(1) of this section. (a) Step 1—Testing in the original state. (1) Tests shall be...

16 CFR 1610.6 - Test procedure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Test procedure. 1610.6 Section 1610.6... FLAMMABILITY OF CLOTHING TEXTILES The Standard § 1610.6 Test procedure. The test procedure is divided into two... according to paragraph (b)(1) of this section. (a) Step 1—Testing in the original state. (1) Tests shall be...

16 CFR 1610.6 - Test procedure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Test procedure. 1610.6 Section 1610.6... FLAMMABILITY OF CLOTHING TEXTILES The Standard § 1610.6 Test procedure. The test procedure is divided into two... according to paragraph (b)(1) of this section. (a) Step 1—Testing in the original state. (1) Tests shall be...

Nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel and stainless steel alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, D.G.; Sorensen, N.R.

1998-02-01

This report presents a nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel alloys from stainless steel alloys as well as an evaluation of cleaning techniques to remove a thermal oxide layer on aircraft exhaust components. The results of this assessment are presented in terms of how effective each technique classifies a known exhaust material. Results indicate that either inspection technique can separate inconel and stainless steel alloys. Based on the experiments conducted, the electrochemical spot test is the optimum for use by airframe and powerplant mechanics. A spot test procedure is proposed for incorporation into themore » Federal Aviation Administration Advisory Circular 65-9A Airframe & Powerplant Mechanic - General Handbook. 3 refs., 70 figs., 7 tabs.« less

40 CFR 63.945 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 11 2014-07-01 2014-07-01 false Test methods and procedures. 63.945...) National Emission Standards for Surface Impoundments § 63.945 Test methods and procedures. (a) Procedure...) The test shall be conducted in accordance with the procedures specified in Method 21 of 40 CFR part 60...

40 CFR 92.125 - Pre-test procedures and preconditioning.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Pre-test procedures and preconditioning... PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.125 Pre-test procedures and preconditioning. (a) Locomotive testing. (1) Determine engine lubricating...

Test Operations Procedure (TOP) 1-2-612 Nuclear Environment Survivability

DTIC Science & Technology

2008-10-24

measurements. The area equal to the area of gamma dose sensitive electronics will be mapped using CaF2 (Mn) TLDs . The selection of each STT...October 2008 8 2.3.3 HEMP / SREMP Instrumentation / Dosimetry . Measurement Parameter Preferred Device Measurement Accuracy Current...Calcium Fluoride Manganese CaF2 (Mn) Thermoluminescent Dosimeter ( TLDs ) and Compton diodes, respectively. The measured gamma dose values will be

Computerized design of speech prostheses.

PubMed

Leonard, R J

1991-08-01

The use of computerized techniques to assist in the design of palatal and/or glossal prostheses is described. Patients with oropharyngeal resection and associated speech impairment are candidates for such prostheses. Procedures discussed allow for the design of some features of the prosthesis, such as shape, location, and tests of its effect on certain speech parameters, prior to actual fabrication. Advantages and current limitations of the techniques are also discussed.

Correlation between Wavelength Dispersive X-ray Fluorescence (WDXRF) analysis of hardened concrete for chlorides vs. Atomic Absorption (AA) analysis in accordance with AASHTO T- 260; sampling and testing for chloride ion in concrete and concrete raw mater

DOT National Transportation Integrated Search

2014-04-01

A correlation between Wavelength Dispersive X-ray Fluorescence(WDXRF) analysis of Hardened : Concrete for Chlorides and Atomic Absorption (AA) analysis (current method AASHTO T-260, procedure B) has been : found and a new method of analysis has been ...

Integrated Eye Tracking and Neural Monitoring for Enhanced Assessment of Mild TBI

DTIC Science & Technology

2015-04-01

virtual reality driving simulator data acquisition. Data collection for the pilot study is nearly complete and data analyses are currently under way...Training for primary study procedures including neuropsychological testing, eye- tracking, virtual reality driving simulator, and EEG data acquisition is...the virtual reality driving simulator. Participants are instructed to drive along a coastal highway while performing the target detection task

An Agent-based Approach to Evaluating the Impact of Technologies on C2

DTIC Science & Technology

2006-06-01

from field experimentation and current military doctrine were identified for the evaluation of SPEYES technologies , which we aligned with field test...and procedures (TTPs). However, the introduction of new technologies to support C2 significantly impacts performance and effectiveness of military ...addressed various challenges of Military Operations in Urban Terrain (MOUT). Our novel approach combined the strengths of field assessment with

Overview of the program to assess the reliability of emerging nondestructive techniques open testing and study of flaw type effect on NDE response

NASA Astrophysics Data System (ADS)

Meyer, Ryan M.; Komura, Ichiro; Kim, Kyung-cho; Zetterwall, Tommy; Cumblidge, Stephen E.; Prokofiev, Iouri

2016-02-01

In February 2012, the U.S. Nuclear Regulatory Commission (NRC) executed agreements with VTT Technical Research Centre of Finland, Nuclear Regulatory Authority of Japan (NRA, former JNES), Korea Institute of Nuclear Safety (KINS), Swedish Radiation Safety Authority (SSM), and Swiss Federal Nuclear Safety Inspectorate (ENSI) to establish the Program to Assess the Reliability of Emerging Nondestructive Techniques (PARENT). The goal of PARENT is to investigate the effectiveness of current emerging and perspective novel nondestructive examination procedures and techniques to find flaws in nickel-alloy welds and base materials. This is done by conducting a series of open and blind international round-robin tests on a set of large-bore dissimilar metal welds (LBDMW), small-bore dissimilar metal welds (SBDMW), and bottom-mounted instrumentation (BMI) penetration weld test blocks. The purpose of blind testing is to study the reliability of more established techniques and included only qualified teams and procedures. The purpose of open testing is aimed at a more basic capability assessment of emerging and novel technologies. The range of techniques applied in open testing varied with respect to maturity and performance uncertainty and were applied to a variety of simulated flaws. This paper will include a brief overview of the PARENT blind and open testing techniques and test blocks and present some of the blind testing results.

Multimodality imaging to plan and guide transcatheter tricuspid valve interventions.

PubMed

Prihadi, Edgard A; Delgado, Victoria; Bax, Jeroen J

2017-10-01

Tricuspid regurgitation (TR) is a highly prevalent valvular heart disease. The natural history of untreated significant TR portends an unfavorable outcome, but only a minority of patients is currently referred for surgical treatment. Organic TR (caused by primary abnormality of the leaflets) is relatively infrequent whereas secondary or functional TR (caused by dilatation of the tricuspid annulus, right ventricle [RV] and right atrium) is the predominant mechanism. The success of transcatheter therapies for left valvular heart disease over the last decade, has fueled similar development of novel transcatheter devices for the treatment of TR. Currently being tested in several clinical trials, each of these devices requires specific needs to define the procedural suitability. In addition, an accurate evaluation of the complex tricuspid anatomy, RV geometry and their relationship with the surrounding structures is mandatory. Therefore, accurate pre-procedural assessment using multimodality imaging techniques will undoubtedly play a pivotal role in achieving procedural success and safety. This review article provides a comprehensive overview on the etiology and different mechanisms of TR, and highlights the role of multimodality imaging techniques in the assessment of TR severity, RV dysfunction and fulfilment of device-specific selection criteria.

Efficiency Benefits Using the Terminal Area Precision Scheduling and Spacing System

NASA Technical Reports Server (NTRS)

Thipphavong, Jane; Swenson, Harry N.; Lin, Paul; Seo, Anthony Y.; Bagasol, Leonard N.

2011-01-01

NASA has developed a capability for terminal area precision scheduling and spacing (TAPSS) to increase the use of fuel-efficient arrival procedures during periods of traffic congestion at a high-density airport. Sustained use of fuel-efficient procedures throughout the entire arrival phase of flight reduces overall fuel burn, greenhouse gas emissions and noise pollution. The TAPSS system is a 4D trajectory-based strategic planning and control tool that computes schedules and sequences for arrivals to facilitate optimal profile descents. This paper focuses on quantifying the efficiency benefits associated with using the TAPSS system, measured by reduction of level segments during aircraft descent and flight distance and time savings. The TAPSS system was tested in a series of human-in-the-loop simulations and compared to current procedures. Compared to the current use of the TMA system, simulation results indicate a reduction of total level segment distance by 50% and flight distance and time savings by 7% in the arrival portion of flight (200 nm from the airport). The TAPSS system resulted in aircraft maintaining continuous descent operations longer and with more precision, both achieved under heavy traffic demand levels.

Operative shortening of the sling as a second-line treatment after TVT failure

PubMed Central

Matuszewski, Marcin; Michajłowski, Jerzy; Krajka, Kazimierz

2011-01-01

Introduction Stress urinary incontinence (SUI) is defined as an involuntary loss of urine during physical exertion, sneezing, coughing, laughing, or other activities that put pressure on the bladder. In some cases, recurrent or persistent SUI after sling operations may be caused by too loose placement of the sling. In the current study, we describe our method of shortening of the sling as a second-line treatment of tension-free vaginal tape (TVT) failure. Materials and methods Four women, aged 46-61, after initial TVT operation were treated for persistent SUI. The severity of SUI was estimated by: physical examinations, cough tests, 24-h pad tests, and King's Health Questionnaire. The shortening procedure, based on excising the fragment of tape and suturing it back, was performed in all patients. Results All cases achieved a good result, which was defined as restoration of full continence. No complications occurred. The 12-month follow-up showed no side-effects. The postoperative control tests: the cough and 24-h pad tests were negative in all women. The general health perceptions increased after the shortening procedure by a mean value 44.25%. The incontinence impact decreased by a mean value 44.6%. In all patients, role and physical limitations significantly decreased (by 88.5% and 80.5%, respectively). The negative emotions connected with SUI significantly decreased after the second procedure. Conclusions The operative shortening of the implanted sling is a simple, cheap, and effective method of second-line treatment in cases of TVT failure and may be offered to the majority of patients with insufficient urethral support after the first procedure. PMID:24578885

Verification of the ODOT overlay design procedure : final report, June 1996.

DOT National Transportation Integrated Search

1996-06-01

The current ODOT overlay design procedure sometimes indicates additional pavement thickness is needed right after the overlay construction. Evaluation of the current procedure reveals that using spreadabiity to back calculate existing pavement modulu...

Robust estimation of the proportion of treatment effect explained by surrogate marker information.

PubMed

Parast, Layla; McDermott, Mary M; Tian, Lu

2016-05-10

In randomized treatment studies where the primary outcome requires long follow-up of patients and/or expensive or invasive obtainment procedures, the availability of a surrogate marker that could be used to estimate the treatment effect and could potentially be observed earlier than the primary outcome would allow researchers to make conclusions regarding the treatment effect with less required follow-up time and resources. The Prentice criterion for a valid surrogate marker requires that a test for treatment effect on the surrogate marker also be a valid test for treatment effect on the primary outcome of interest. Based on this criterion, methods have been developed to define and estimate the proportion of treatment effect on the primary outcome that is explained by the treatment effect on the surrogate marker. These methods aim to identify useful statistical surrogates that capture a large proportion of the treatment effect. However, current methods to estimate this proportion usually require restrictive model assumptions that may not hold in practice and thus may lead to biased estimates of this quantity. In this paper, we propose a nonparametric procedure to estimate the proportion of treatment effect on the primary outcome that is explained by the treatment effect on a potential surrogate marker and extend this procedure to a setting with multiple surrogate markers. We compare our approach with previously proposed model-based approaches and propose a variance estimation procedure based on a perturbation-resampling method. Simulation studies demonstrate that the procedure performs well in finite samples and outperforms model-based procedures when the specified models are not correct. We illustrate our proposed procedure using a data set from a randomized study investigating a group-mediated cognitive behavioral intervention for peripheral artery disease participants. Copyright © 2015 John Wiley & Sons, Ltd.

40 CFR 1066.840 - Highway fuel economy test procedure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Highway fuel economy test procedure... Highway fuel economy test procedure. This section describes the procedure for the highway fuel economy test (HFET). This test involves emission sampling and fuel economy measurement for certain vehicles as...

76 FR 65631 - Energy Conservation Program: Test Procedures for Microwave Ovens

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... Conservation Program: Test Procedures for Microwave Ovens AGENCY: Office of Energy Efficiency and Renewable... (DOE) has initiated a test procedure rulemaking to develop active mode testing methodologies for... Federal Register a final rule for the microwave oven test procedure rulemaking (July TP repeal final rule...

78 FR 63823 - Energy Conservation Program: Test Procedures for Television Sets

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

... Conservation Program: Test Procedures for Television Sets AGENCY: Office of Energy Efficiency and Renewable... Energy (DOE) issued a notice of proposed rulemaking (NOPR) to establish a new test procedure for... additional testing and proposed amendments to the TV test procedure in its March 12, 2013 supplemental notice...

78 FR 38455 - Energy Conservation Program: Test Procedures for Electric Motors

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-26

... Conservation Program: Test Procedures for Electric Motors; Proposed Rule #0;#0;Federal Register / Vol. 78, No... 431 [Docket No. EERE-2012-BT-TP-0043] RIN 1904-AC89 Energy Conservation Program: Test Procedures for... establishing definitions, specifying testing set-up procedures necessary to test, and extending DOE's existing...

76 FR 50145 - Energy Conservation Program: Test Procedures for Residential Clothes Dryers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-12

... EERE-2011-BT-TP-0054] RIN 1904-AC63 Energy Conservation Program: Test Procedures for Residential...: Request for information. SUMMARY: The U.S. Department of Energy (DOE) has initiated a test procedure... clothes dryer test procedure. DOE will address the issues surrounding testing of automatic cycle...

40 CFR 61.304 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false Test methods and procedures. 61.304... Emissions From Benzene Transfer Operations § 61.304 Test methods and procedures. (a) The procedures for... testing equipment shall be prepared and installed as specified in the appropriate test methods. (2) The...

40 CFR 61.304 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false Test methods and procedures. 61.304... Emissions From Benzene Transfer Operations § 61.304 Test methods and procedures. (a) The procedures for... testing equipment shall be prepared and installed as specified in the appropriate test methods. (2) The...

40 CFR 61.304 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false Test methods and procedures. 61.304... Emissions From Benzene Transfer Operations § 61.304 Test methods and procedures. (a) The procedures for... testing equipment shall be prepared and installed as specified in the appropriate test methods. (2) The...

40 CFR 61.304 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Test methods and procedures. 61.304... Emissions From Benzene Transfer Operations § 61.304 Test methods and procedures. (a) The procedures for... testing equipment shall be prepared and installed as specified in the appropriate test methods. (2) The...

40 CFR 61.304 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false Test methods and procedures. 61.304... Emissions From Benzene Transfer Operations § 61.304 Test methods and procedures. (a) The procedures for... testing equipment shall be prepared and installed as specified in the appropriate test methods. (2) The...

40 CFR 86.1227-96 - Test procedures; overview.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Test procedures; overview. 86.1227-96... Emission Test Procedures for New Gasoline-Fueled, Natural Gas-Fueled, Liquefied Petroleum Gas-Fueled and Methanol-Fueled Heavy-Duty Vehicles § 86.1227-96 Test procedures; overview. (a) The overall test consists...

40 CFR 90.411 - Post-test analyzer procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Post-test analyzer procedures. 90.411... Test Procedures § 90.411 Post-test analyzer procedures. (a) Perform a HC hang-up check within 60...), the test is void. (d) Read and record the post-test data specified in § 90.405(e). (e) For a valid...

40 CFR 90.411 - Post-test analyzer procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Post-test analyzer procedures. 90.411... Test Procedures § 90.411 Post-test analyzer procedures. (a) Perform a HC hang-up check within 60...), the test is void. (d) Read and record the post-test data specified in § 90.405(e). (e) For a valid...

40 CFR 90.411 - Post-test analyzer procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Post-test analyzer procedures. 90.411... Test Procedures § 90.411 Post-test analyzer procedures. (a) Perform a HC hang-up check within 60...), the test is void. (d) Read and record the post-test data specified in § 90.405(e). (e) For a valid...

40 CFR 90.411 - Post-test analyzer procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Post-test analyzer procedures. 90.411... Test Procedures § 90.411 Post-test analyzer procedures. (a) Perform a HC hang-up check within 60...), the test is void. (d) Read and record the post-test data specified in § 90.405(e). (e) For a valid...

40 CFR 90.411 - Post-test analyzer procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Post-test analyzer procedures. 90.411... Test Procedures § 90.411 Post-test analyzer procedures. (a) Perform a HC hang-up check within 60...), the test is void. (d) Read and record the post-test data specified in § 90.405(e). (e) For a valid...

Trends in surgical management and pre-operative urodynamics in female medicare beneficiaries with mixed incontinence.

PubMed

Chughtai, Bilal; Hauser, Nicholas; Anger, Jennifer; Asfaw, Tirsit; Laor, Leanna; Mao, Jialin; Lee, Richard; Te, Alexis; Kaplan, Steven; Sedrakyan, Art

2017-02-01

We sought to examine the surgical trends and utilization of treatment for mixed urinary incontinence among female Medicare beneficiaries. Data was obtained from a 5% national random sample of outpatient and carrier claims from 2000 to 2011. Included were female patients 65 and older, diagnosed with mixed urinary incontinence, who underwent surgical treatment identified by Current Procedural Terminology, Fourth Edition (CPT-4) codes. Urodynamics (UDS) before initial and secondary procedure were also identified using CPT-4 codes. Procedural trends and utilization of UDS were analyzed. Utilization of UDS increased during the study period, from 38.4% to 74.0% prior to initial surgical intervention, and from 28.6% to 62.5% preceding re-intervention. Sling surgery (63.0%) and injectable bulking agents (28.0%) were the most common surgical treatments adopted, followed by sacral nerve stimulation (SNS) (4.8%) and Burch (4.0%) procedures. Re-intervention was performed in 4.0% of patients initially treated with sling procedures and 21.3% of patients treated with bulking agents, the majority of whom (51.7% and 76.3%, respectively) underwent injection of a bulking agent. Risk of re-intervention was not different among those who did or did not receive urodynamic tests prior to the initial procedure (8.5% vs. 9.3%) CONCLUSIONS: Sling and bulk agents are the most common treatment for MUI. Preoperative urodynamic testing was not related to risk of re-intervention following surgery for mixed urinary incontinence in this cohort. Neurourol. Urodynam. 36:422-425, 2017. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

'It is Time to Prepare the Next patient' Real-Time Prediction of Procedure Duration in Laparoscopic Cholecystectomies.

PubMed

Guédon, Annetje C P; Paalvast, M; Meeuwsen, F C; Tax, D M J; van Dijke, A P; Wauben, L S G L; van der Elst, M; Dankelman, J; van den Dobbelsteen, J J

2016-12-01

Operating Room (OR) scheduling is crucial to allow efficient use of ORs. Currently, the predicted durations of surgical procedures are unreliable and the OR schedulers have to follow the progress of the procedures in order to update the daily planning accordingly. The OR schedulers often acquire the needed information through verbal communication with the OR staff, which causes undesired interruptions of the surgical process. The aim of this study was to develop a system that predicts in real-time the remaining procedure duration and to test this prediction system for reliability and usability in an OR. The prediction system was based on the activation pattern of one single piece of equipment, the electrosurgical device. The prediction system was tested during 21 laparoscopic cholecystectomies, in which the activation of the electrosurgical device was recorded and processed in real-time using pattern recognition methods. The remaining surgical procedure duration was estimated and the optimal timing to prepare the next patient for surgery was communicated to the OR staff. The mean absolute error was smaller for the prediction system (14 min) than for the OR staff (19 min). The OR staff doubted whether the prediction system could take all relevant factors into account but were positive about its potential to shorten waiting times for patients. The prediction system is a promising tool to automatically and objectively predict the remaining procedure duration, and thereby achieve optimal OR scheduling and streamline the patient flow from the nursing department to the OR.

''Football'' test coil: a simulated service test of internally-cooled, cabled superconductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marston, P.G.; Iwasa, Y.; Thome, R.J.

Internally-cooled, cabled superconductor, (ICCS), appears from small-scale tests to be a viable alternative to pool-boiling cooled superconductors for large superconducting magnets. Potential advantages may include savings in helium inventory, smaller structure and ease of fabrication. Questions remain, however, about the structural performance of these systems. The ''football'' test coil has been designed to simulate the actual ''field-current-stress-thermal'' operating conditions of a 25 ka ICCS in a commercial scale MHD magnet. The test procedure will permit demonstration of the 20 year cyclic life of such a magnet in less than 20 days. This paper describes the design, construction and test ofmore » that coil which is wound of copper-stabilized niobium-titanium cable in steel conduit. 2 refs.« less

Reduction in in vivo testing at the National Veterinary Services Laboratories of the United States Department of Agriculture.

PubMed

Hyde, R L

1986-01-01

Efforts are being made at the National Veterinary Services Laboratories to reduce in vivo testing of USDA licensed veterinary vaccines. A hemagglutination test for determining potency of killed parvovirus vaccine is currently being used for canine and swine adjuvanted and nonadjuvanted products; a serum neutralization inhibition test (SNIT) is being developed for potency testing of killed adjuvanted infectious bovine rhinotracheitis (IBR), bovine virus diarrhea (BVD) and parainfluenza (PI3) vaccines: and a tissue culture titration method for live avian encephalomyelitis virus vaccine is being pursued as a replacement for the old hatch-out chick embryo titration method. Difficulties in separating the antigen from oil emulsion products are preventing significant advances in developing in vitro testing procedures for poultry killed-virus vaccines.

Aerodynamic and hydrodynamic model tests of the Enserch Garden Banks floating production facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, E.W.; Bauer, T.C.; Kelly, P.J.

1995-12-01

This paper presents the results of aerodynamic and hydrodynamic model tests of the Enserch Garden Banks, a semisubmersible Floating Production Facility (FPF) moored in 2,190-ft waters. During the wind tunnel tests, the steady component of wind and current forces/moments at various skew and heel axes were measured. The results were compared and calibrated against analytical calculations using techniques recommended by ABS and API. During the wave basin recommend test the mooring line tensions and vessel motions including the effects of dynamic wind and current were measured. An analytical calculation of the airgap, vessel motions, and mooring line loads were comparedmore » with wave basin model test results. This paper discusses the test objectives, test setups and agendas for wind and wave basin testing of a deepwater permanently moored floating production system. The experience from these tests and the comparison of measured tests results with analytical calculations will be of value to designers and operators contemplating the use of a semisubmersible based floating production system. The analysis procedures are aimed at estimating (1) vessel motions, (2) airgap, and (3) mooring line tensions with reasonable accuracy. Finally, this paper demonstrates how the model test results were interpolated and adapted in the design loop.« less

The Lewis Research Center geomagnetic substorm simulation facility

NASA Technical Reports Server (NTRS)

Berkopec, F. D.; Stevens, N. J.; Sturman, J. C.

1977-01-01

A simulation facility was established to determine the response of typical spacecraft materials to the geomagnetic substorm environment and to evaluate instrumentation that will be used to monitor spacecraft system response to this environment. Space environment conditions simulated include the thermal-vacuum conditions of space, solar simulation, geomagnetic substorm electron fluxes and energies, and the low energy plasma environment. Measurements for spacecraft material tests include sample currents, sample surface potentials, and the cumulative number of discharges. Discharge transients are measured by means of current probes and oscilloscopes and are verified by a photomultiplier. Details of this facility and typical operating procedures are presented.

Fuzzy model-based fault detection and diagnosis for a pilot heat exchanger

NASA Astrophysics Data System (ADS)

Habbi, Hacene; Kidouche, Madjid; Kinnaert, Michel; Zelmat, Mimoun

2011-04-01

This article addresses the design and real-time implementation of a fuzzy model-based fault detection and diagnosis (FDD) system for a pilot co-current heat exchanger. The design method is based on a three-step procedure which involves the identification of data-driven fuzzy rule-based models, the design of a fuzzy residual generator and the evaluation of the residuals for fault diagnosis using statistical tests. The fuzzy FDD mechanism has been implemented and validated on the real co-current heat exchanger, and has been proven to be efficient in detecting and isolating process, sensor and actuator faults.

Sensitivity Study of the Wall Interference Correction System (WICS) for Rectangular Tunnels

NASA Technical Reports Server (NTRS)

Walker, Eric L.; Everhart, Joel L.; Iyer, Venkit

2001-01-01

An off-line version of the Wall Interference Correction System (WICS) has been implemented for the NASA Langley National Transonic Facility. The correction capability is currently restricted to corrections for solid wall interference in the model pitch plane for Mach numbers less than 0.45 due to a limitation in tunnel calibration data. A study to assess output sensitivity to measurement uncertainty was conducted to determine standard operational procedures and guidelines to ensure data quality during the testing process. Changes to the current facility setup and design recommendations for installing the WICS code into a new facility are reported.

Model Scaling of Hydrokinetic Ocean Renewable Energy Systems

NASA Astrophysics Data System (ADS)

von Ellenrieder, Karl; Valentine, William

2013-11-01

Numerical simulations are performed to validate a non-dimensional dynamic scaling procedure that can be applied to subsurface and deeply moored systems, such as hydrokinetic ocean renewable energy devices. The prototype systems are moored in water 400 m deep and include: subsurface spherical buoys moored in a shear current and excited by waves; an ocean current turbine excited by waves; and a deeply submerged spherical buoy in a shear current excited by strong current fluctuations. The corresponding model systems, which are scaled based on relative water depths of 10 m and 40 m, are also studied. For each case examined, the response of the model system closely matches the scaled response of the corresponding full-sized prototype system. The results suggest that laboratory-scale testing of complete ocean current renewable energy systems moored in a current is possible. This work was supported by the U.S. Southeast National Marine Renewable Energy Center (SNMREC).

Collaborative study for the standardisation of the histamine sensitizing test in mice and the CHO cell-based assay for the residual toxicity testing of acellular pertussis vaccines.

PubMed

Xing, D; Maes, A; Behr-Gross, M-E; Costanzo, A; Daas, A; Buchheit, K-H

2010-04-01

The European Pharmacopoeia (Ph. Eur.) and the World Health Organisation (WHO) require the performance of extensive quality and safety control testing before the release on the market of vaccine products for human use. Safety testing with regard to residual pertussis toxin (PT) in acellular pertussis combination vaccines is performed through assessment of fatal sensitisation of mice to histamine challenge by the vaccine product under test. Currently, use of different in-house procedures and no requirement for the inclusion of a standard reference in each assay render comparisons of results obtained for identical vaccine batches between different control laboratories very difficult. At the initiative of the European Directorate for the Quality of Medicines and HealthCare (EDQM), an international collaborative study was organised for the standardization of the Histamine Sensitizing Test (HIST) in mice and the Chinese Hamster Ovary (CHO)-cell-based assay (performed at the bulk product level) for the residual toxicity testing of acellular pertussis vaccines or acellular pertussis-based combination vaccines. The study was run under the aegis of the Biological Standardisation Programme, jointly supported by the Council of Europe and the European Commission under the project code BSP076. Ten (10) laboratories participated in the study and were requested to perform 3 independent Histamine Sensitizing Tests in mice and to report results of the lethal end-point measurement as prescribed by the Ph. Eur. monographs. Some of them also reported data from an in-house validated CHO-cell-based assay. In addition, some of the laboratories reported concomitantly data obtained by measurement of the drop in temperature induced after the histamine challenge, a method currently under investigation to be added as an alternative end-point for the HIST in the Ph. Eur. monographs for acellular pertussis-based combination vaccines in order to alleviate animal suffering (in application of the 3Rs principle). Based on the results of the collaborative study, a potency of 7500 IU/vial (International Units per vial) was assigned to the current Ph. Eur. Biological Reference Preparation (BRP) for PT. The results of the study also show that 1) intra- and inter-laboratory variations can be improved by the use of a validated standard operating procedure; 2) inclusion in each assay of a standard reference sample, calibrated in IU, can increase comparability of results among laboratories and thus help to reduce repeat testing; 3) a correlation between mortality data and temperature data was observed although, due to the limited number of data sets and the lack of a common method for the temperature end-point, further investigation of this point is required; 4) the CHO-cell-based assay did not yield comparable results and further standardisation of the assay procedure may be investigated in a follow-up project.

40 CFR 60.675 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Test methods and procedures. 60.675... Mineral Processing Plants § 60.675 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in...

40 CFR 60.644 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Test methods and procedures. 60.644... Gas Processing: SO2 Emissions § 60.644 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test...

14 CFR Appendix F to Part 23 - Test Procedure

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Test Procedure F Appendix F to Part 23...—Test Procedure Acceptable test procedure for self-extinguishing materials for showing compliance with... as sandwich panels, may not be separated for a test. The specimen thickness must be no thicker than...

40 CFR 94.109 - Test procedures for Category 3 marine engines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Test procedures for Category 3 marine... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES Test Procedures § 94.109 Test procedures for Category 3 marine engines. (a) Gaseous emissions shall be measured using the test...

40 CFR 94.109 - Test procedures for Category 3 marine engines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Test procedures for Category 3 marine... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES Test Procedures § 94.109 Test procedures for Category 3 marine engines. (a) Gaseous emissions shall be measured using the test...

40 CFR 60.503 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Test methods and procedures. 60.503... Terminals § 60.503 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of...

40 CFR 60.503 - Test methods and procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Test methods and procedures. 60.503... Terminals § 60.503 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of...

40 CFR 60.503 - Test methods and procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Test methods and procedures. 60.503... Terminals § 60.503 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of...

40 CFR 60.503 - Test methods and procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Test methods and procedures. 60.503... Terminals § 60.503 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of...

40 CFR 60.503 - Test methods and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Test methods and procedures. 60.503... Terminals § 60.503 Test methods and procedures. (a) In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of...

16 CFR § 1610.6 - Test procedure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Test procedure. § 1610.6 Section § 1610.6... FLAMMABILITY OF CLOTHING TEXTILES The Standard § 1610.6 Test procedure. The test procedure is divided into two... according to paragraph (b)(1) of this section. (a) Step 1—Testing in the original state. (1) Tests shall be...

An adaptive large neighborhood search procedure applied to the dynamic patient admission scheduling problem.

PubMed

Lusby, Richard Martin; Schwierz, Martin; Range, Troels Martin; Larsen, Jesper

2016-11-01

The aim of this paper is to provide an improved method for solving the so-called dynamic patient admission scheduling (DPAS) problem. This is a complex scheduling problem that involves assigning a set of patients to hospital beds over a given time horizon in such a way that several quality measures reflecting patient comfort and treatment efficiency are maximized. Consideration must be given to uncertainty in the length of stays of patients as well as the possibility of emergency patients. We develop an adaptive large neighborhood search (ALNS) procedure to solve the problem. This procedure utilizes a Simulated Annealing framework. We thoroughly test the performance of the proposed ALNS approach on a set of 450 publicly available problem instances. A comparison with the current state-of-the-art indicates that the proposed methodology provides solutions that are of comparable quality for small and medium sized instances (up to 1000 patients); the two approaches provide solutions that differ in quality by approximately 1% on average. The ALNS procedure does, however, provide solutions in a much shorter time frame. On larger instances (between 1000-4000 patients) the improvement in solution quality by the ALNS procedure is substantial, approximately 3-14% on average, and as much as 22% on a single instance. The time taken to find such results is, however, in the worst case, a factor 12 longer on average than the time limit which is granted to the current state-of-the-art. The proposed ALNS procedure is an efficient and flexible method for solving the DPAS problem. Copyright © 2016 Elsevier B.V. All rights reserved.

Colonoscopy Screening in the US Astronaut Corps

NASA Technical Reports Server (NTRS)

Masterova, K.; Van Baalen, M.; Wear, M. L.; Murray, J.; Schaefer, C.

2016-01-01

BACKGROUND: Historically, colonoscopy screenings for astronauts have been conducted to ensure that astronauts are in good health for space missions. Recently this historical data has been identified as being useful for developing an occupational surveillance requirement. It can be used to assess overall colon health and to have a point of reference for future tests in current and former astronauts, as well as to follow-up and track rates of colorectal cancer and polyps. These rates can be compared to military and other terrestrial populations. In 2003, the active astronaut colonoscopy requirements changed to require less frequent colonoscopies. Since polyp removal during a colonoscopy is an intervention that prevents the polyp from potentially developing into cancer, the procedure decreases the individual's risk for colon cancer. The objective of this study is to evaluate the possible effect of increased follow-up times between colonoscopies on the number and severity of polyps identified during the procedures among both current and former NASA astronauts. Initial results and forward work regarding astronaut colonoscopy screenings will be presented. METHODS: A retrospective study of all colonoscopy procedures performed on NASA astronauts between 1962 and 2015 (both during active career and retirement) was conducted by review of the JSC Clinic Electronic Medical Record and Lifetime Surveillance of Astronaut Health (LSAH) database for colonoscopy screening procedures and pathology reports. The timeframe of interest was from the time of selection into the Astronaut Corps through May 2015 or death. For each colonoscopy report, the following data were captured: date of procedure, age at time of procedure, reason for procedure, quality of bowel prep, completion of procedure and/or reason for termination of procedure, findings of procedure, subsequent treatment (if any), recommended follow-up interval, actual follow up interval, family history of polyps or colon cancer, and other significant items or discrepancies. The population consisted of 338 astronauts: 52 females, 286 males. Of these, 56 were deceased, and 11 astronauts had no record of any colonoscopies. Because of a screening requirement change in 2003, analyses were conducted to determine if there were differences between the two time periods. One-sided Wilcoxon rank sum tests were used to identify statistically significant differences between the two time periods. RESULTS: There was a combined total of 1,964 colonoscopy screenings identified. The average follow-up intervals between colonoscopies were indeed longer after the screening requirement change than before the change. The mean follow-up interval pre -2003 was 3.59 years, while post-2003 it increased to 4.35 years. The statistical significance of this difference was confirmed using a one sided Wilcoxon rank sum test which yielded p<.001. Colonoscopies performed after the requirement change tended to have a higher incidence and greater severity of polyps. From pre-2003 to post-2003 the percentage of colonoscopy procedures yielding no polyps decreased from 83.77% to 74.70%. Not only did post-2003 procedures yield more polyp findings, but the polyps recorded were more often of severe pathology. Before 2003 3.62% of colonoscopy findings were polyps of the hyperplastic type (the least severe polyp type) and only 3.35% were of greater severity. Post-2003, 4.21% of findings were hyperplastic polyps while 11.44% were of greater severity. Upon the investigation of other possible contributing factors to these results, we also found that mean age post-2003 was 54.55 years which was significantly higher than during the pre-2003 timeframe (47.32 years). This was observed with a one-sided Wilcoxon rank sum test, resulting in a p<0.001. The increased average age of astronauts could also be a contributing factor to the greater number of polyps found since the risk of developing polyps increases with age. Further work is needed to better understand the increased incidence and greater severity of polyps found in astronaut colonoscopy outcomes.

40 CFR 87.62 - Test procedure (propulsion engines).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Test procedure (propulsion engines). 87.62 Section 87.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) Definitions. Test Procedures § 87.62 Test procedure (propulsion engines). Link to an...

40 CFR 610.65 - Other test procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Other test procedures. 610.65 Section 610.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.65 Other...

40 CFR 610.64 - Track test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Track test procedures. 610.64 Section 610.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.64 Track...

40 CFR 610.65 - Other test procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Other test procedures. 610.65 Section 610.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.65 Other...

40 CFR 610.65 - Other test procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Other test procedures. 610.65 Section 610.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.65 Other...

40 CFR 610.65 - Other test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Other test procedures. 610.65 Section 610.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.65 Other...

49 CFR 581.7 - Test procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Test procedures. 581.7 Section 581.7... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) BUMPER STANDARD § 581.7 Test procedures. (a) Longitudinal impact test procedures. (1) Impact the vehicle's front surface and its rear surface two times each...

49 CFR 581.7 - Test procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Test procedures. 581.7 Section 581.7... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) BUMPER STANDARD § 581.7 Test procedures. (a) Longitudinal impact test procedures. (1) Impact the vehicle's front surface and its rear surface two times each...

40 CFR 610.65 - Other test procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Other test procedures. 610.65 Section 610.65 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria Special Test Procedures § 610.65 Other...