Life cycle assessment of fuel ethanol produced from soluble sugar in sweet sorghum stalks in North China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Ning; Yang, Yang; Cai, Hao

This paper describes the results of a life cycle assessment of sweet sorghum stalk (SSS)-based ethanol in North China. We determined the environmental performance of SSS-based ethanol and examined its advantages and disadvantages, as compared to gasoline, focusing on the life cycle of feedstock production, transportation, ethanol production and distribution, and use. The GREET transportation model and the method developed by the Centre of Environmental Sciences at Leiden University (CML method) were used to compile a life cycle inventory and to assess environmental impacts. Results indicate that SSS-based ethanol has advantages in terms of energy consumption, with a well tomore » wheel decrease of 85% fossil energy and 44% global warming potential, as compared with gasoline. Abiotic depletion potential, acidification potential, and photochemical ozone creation potential were also 50–90% lower than in the case of gasoline, while human health toxic potential was 36% lower. However, SSS-based sorghum did not have advantages over gasoline in terms of life cycle cost, land use, and water consumption. Results indicate that such an evaluation cannot just consider a few types of environmental impacts, researchers should promote systematic and comprehensive life cycle assessment of ethanol to guide the development of an energy strategy for China.« less

ENVIRONMENTAL COMPARISON OF GASOLINE BLENDING OPTIONS USING LIFE CYCLE ASSESSMENT

EPA Science Inventory

A life cycle assessment has been done on various gasoline blends, The purpose of this study is to compare several gasoline blends of 95 and 98 octaine, that meet the vapour pressure upper limit requirement of 60 kPa. This study accounts for the gasoline losses due to evaporation ...

Impact of Accreditation on Public and Private Universities: A Comparative Study

ERIC Educational Resources Information Center

Dattey, Kwame; Westerheijden, Don F.; Hofman, Wiecher H. Adriaan

2014-01-01

Based on two cycles of assessments for accreditation, this study assesses the differential impacts of accreditation on public and private universities in Ghana. Analysis of the evaluator reports indicates no statistically significant difference--improvement or deterioration--between the two cycles of evaluations for both types of institutions. A…

Technical and economic evaluation of a Brayton-Rankine combined cycle solar-thermal power plant

NASA Astrophysics Data System (ADS)

Wright, J. D.; Copeland, R. J.

1981-05-01

An assessment of gas-liquid direct-contact heat exchange and of a new storage-coupled system was conducted. Both technical and economic issues are evaluated. Specifically, the storage-coupled combined cycle is compared with a molten salt system. The open Brayton cycle system is used as a topping cycle, and the reject heat powers the molten salt/Rankine system. In this study the molten salt system is left unmodified, the Brayton cycle is integrated on top of a Marietta description of an existing molten salt plant. This compares a nonoptimized combined cycle with an optimized molten salt system.

Life Cycle Assessment of III-V Precursors for Photovoltaic and Semiconductor Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horowitz, Kelsey A; Smith, Brittany L.; Babbitt, Callie W.

This study provides detailed information on the manufacture of III-V metal organic vapor phase epitaxy precursors through extensive literature and patent research. This data informed a cradle-to-gate life cycle assessment of these chemicals. Reported impacts include cumulative energy demand and greenhouse gas emissions. The results were interpreted to identify sources of environmental burden within the life cycle and were compared to energy demand reported in previous studies.

Comparing the Life Cycle Energy Consumption, Global ...

EPA Pesticide Factsheets

Managing the water-energy-nutrient nexus for the built environment requires, in part, a full system analysis of energy consumption, global warming and eutrophication potentials of municipal water services. As an example, we evaluated the life cycle energy use, greenhouse gas (GHG) emissions and aqueous nutrient releases of the whole anthropogenic municipal water cycle starting from raw water extraction to wastewater treatment and reuse/discharge for five municipal water and wastewater systems. The assessed options included conventional centralized services and four alternative options following the principles of source-separation and water fit-for-purpose. The comparative life cycle assessment identified that centralized drinking water supply coupled with blackwater energy recovery and on-site greywater treatment and reuse was the most energyand carbon-efficient water service system evaluated, while the conventional (drinking water and sewerage) centralized system ranked as the most energy- and carbon-intensive system. The electricity generated from blackwater and food residuals co-digestion was estimated to offset at least 40% of life cycle energy consumption for water/waste services. The dry composting toilet option demonstrated the lowest life cycle eutrophication potential. The nutrients in wastewater effluent are the dominating contributors for the eutrophication potential for the assessed system configurations. Among the parameters for which variability

Power output measurement during treadmill cycling.

PubMed

Coleman, D A; Wiles, J D; Davison, R C R; Smith, M F; Swaine, I L

2007-06-01

The study aim was to consider the use of a motorised treadmill as a cycling ergometry system by assessing predicted and recorded power output values during treadmill cycling. Fourteen male cyclists completed repeated cycling trials on a motorised treadmill whilst riding their own bicycle fitted with a mobile ergometer. The speed, gradient and loading via an external pulley system were recorded during 20-s constant speed trials and used to estimate power output with an assumption about the contribution of rolling resistance. These values were then compared with mobile ergometer measurements. To assess the reliability of measured power output values, four repeated trials were conducted on each cyclist. During level cycling, the recorded power output was 257.2 +/- 99.3 W compared to the predicted power output of 258.2 +/- 99.9 W (p > 0.05). For graded cycling, there was no significant difference between measured and predicted power output, 268.8 +/- 109.8 W vs. 270.1 +/- 111.7 W, p > 0.05, SEE 1.2 %. The coefficient of variation for mobile ergometer power output measurements during repeated trials ranged from 1.5 % (95 % CI 1.2 - 2.0 %) to 1.8 % (95 % CI 1.5 - 2.4 %). These results indicate that treadmill cycling can be used as an ergometry system to assess power output in cyclists with acceptable accuracy.

UTILITY OF A FULL LIFE-CYCLE COPEPOD BIOASSAY APPROACH FOR ASSESSMENT OF SEDIMENT-ASSOCIATED CONTAMINANT MIXTURES. (R825279)

EPA Science Inventory

Abstract

We compared a 21 day full life-cycle bioassay with an existing 14 day partial life-cycle bioassay for two species of meiobenthic copepods, Microarthridion littorale and Amphiascus tenuiremis. We hypothesized that full life-cycle tests would bette...

Life cycle assessment of a packaging waste recycling system in Portugal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferreira, S.; Cabral, M.; Cruz, N.F. da, E-mail: nunocruz@tecnico.ulisboa.pt

Highlights: • We modeled a real packaging waste recycling system. • The analysis was performed using the life cycle assessment methodology. • The 2010 situation was compared with scenarios where the materials were not recycled. • The “Baseline” scenario seems to be more beneficial to the environment. - Abstract: Life Cycle Assessment (LCA) has been used to assess the environmental impacts associated with an activity or product life cycle. It has also been applied to assess the environmental performance related to waste management activities. This study analyses the packaging waste management system of a local public authority in Portugal. Themore » operations of selective and refuse collection, sorting, recycling, landfilling and incineration of packaging waste were considered. The packaging waste management system in operation in 2010, which we called “Baseline” scenario, was compared with two hypothetical scenarios where all the packaging waste that was selectively collected in 2010 would undergo the refuse collection system and would be sent directly to incineration (called “Incineration” scenario) or to landfill (“Landfill” scenario). Overall, the results show that the “Baseline” scenario is more environmentally sound than the hypothetical scenarios.« less

LIFE CYCLE BASED STUDIES ON BIOETHANOL FUEL FOR SUSTAINABLE TRANSPORTATION: A LITERATURE REVIEW

EPA Science Inventory

A literature search was conducted and revealed 45 publications (1996-2005) that compare bio-ethanol systems to conventional fuel on a life-cycle basis, or using life cycle assessment. Feedstocks, such as sugar beets, wheat, potato, sugar cane, and corn, have been investigated in...

Understanding future emissions from low-carbon power systems by integration of life-cycle assessment and integrated energy modelling

NASA Astrophysics Data System (ADS)

Pehl, Michaja; Arvesen, Anders; Humpenöder, Florian; Popp, Alexander; Hertwich, Edgar G.; Luderer, Gunnar

2017-12-01

Both fossil-fuel and non-fossil-fuel power technologies induce life-cycle greenhouse gas emissions, mainly due to their embodied energy requirements for construction and operation, and upstream CH4 emissions. Here, we integrate prospective life-cycle assessment with global integrated energy-economy-land-use-climate modelling to explore life-cycle emissions of future low-carbon power supply systems and implications for technology choice. Future per-unit life-cycle emissions differ substantially across technologies. For a climate protection scenario, we project life-cycle emissions from fossil fuel carbon capture and sequestration plants of 78-110 gCO2eq kWh-1, compared with 3.5-12 gCO2eq kWh-1 for nuclear, wind and solar power for 2050. Life-cycle emissions from hydropower and bioenergy are substantial (˜100 gCO2eq kWh-1), but highly uncertain. We find that cumulative emissions attributable to upscaling low-carbon power other than hydropower are small compared with direct sectoral fossil fuel emissions and the total carbon budget. Fully considering life-cycle greenhouse gas emissions has only modest effects on the scale and structure of power production in cost-optimal mitigation scenarios.

Comparative life cycle assessment of battery storage systems for stationary applications.

PubMed

Hiremath, Mitavachan; Derendorf, Karen; Vogt, Thomas

2015-04-21

This paper presents a comparative life cycle assessment of cumulative energy demand (CED) and global warming potential (GWP) of four stationary battery technologies: lithium-ion, lead-acid, sodium-sulfur, and vanadium-redox-flow. The analyses were carried out for a complete utilization of their cycle life and for six different stationary applications. Due to its lower CED and GWP impacts, a qualitative analysis of lithium-ion was carried out to assess the impacts of its process chains on 17 midpoint impact categories using ReCiPe-2008 methodology. It was found that in general the use stage of batteries dominates their life cycle impacts significantly. It is therefore misleading to compare the environmental performance of batteries only on a mass or capacity basis at the manufacturing outlet ("cradle-to-gate analyses") while neglecting their use stage impacts, especially when they have different characteristic parameters. Furthermore, the relative ranking of batteries does not show a significant dependency on the investigated stationary application scenarios in most cases. Based on the results obtained, the authors go on to recommend the deployment of batteries with higher round-trip efficiency, such as lithium-ion, for stationary grid operation in the first instance.

A fuel cycle assessment guide for utility and state energy planners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-07-01

This guide, one in a series of documents designed to help assess fuel cycles, is a framework for setting parameters, collecting data, and analyzing fuel cycles for supply-side and demand-side management. It provides an automated tool for entering comparative fuel cycle data that are meaningful to state and utility integrated resource planning, collaborative, and regional energy planning activities. It outlines an extensive range of energy technology characteristics and environmental, social, and economic considerations within each stage of a fuel cycle. The guide permits users to focus on specific stages or effects that are relevant to the technology being evaluated andmore » that meet the user`s planning requirements.« less

Automated respiratory cycles selection is highly specific and improves respiratory mechanics analysis.

PubMed

Rigo, Vincent; Graas, Estelle; Rigo, Jacques

2012-07-01

Selected optimal respiratory cycles should allow calculation of respiratory mechanic parameters focusing on patient-ventilator interaction. New computer software automatically selecting optimal breaths and respiratory mechanics derived from those cycles are evaluated. Retrospective study. University level III neonatal intensive care unit. Ten mins synchronized intermittent mandatory ventilation and assist/control ventilation recordings from ten newborns. The ventilator provided respiratory mechanic data (ventilator respiratory cycles) every 10 secs. Pressure, flow, and volume waves and pressure-volume, pressure-flow, and volume-flow loops were reconstructed from continuous pressure-volume recordings. Visual assessment determined assisted leak-free optimal respiratory cycles (selected respiratory cycles). New software graded the quality of cycles (automated respiratory cycles). Respiratory mechanic values were derived from both sets of optimal cycles. We evaluated quality selection and compared mean values and their variability according to ventilatory mode and respiratory mechanic provenance. To assess discriminating power, all 45 "t" values obtained from interpatient comparisons were compared for each respiratory mechanic parameter. A total of 11,724 breaths are evaluated. Automated respiratory cycle/selected respiratory cycle selections agreement is high: 88% of maximal κ with linear weighting. Specificity and positive predictive values are 0.98 and 0.96, respectively. Averaged values are similar between automated respiratory cycle and ventilator respiratory cycle. C20/C alone is markedly decreased in automated respiratory cycle (1.27 ± 0.37 vs. 1.81 ± 0.67). Tidal volume apparent similarity disappears in assist/control: automated respiratory cycle tidal volume (4.8 ± 1.0 mL/kg) is significantly lower than for ventilator respiratory cycle (5.6 ± 1.8 mL/kg). Coefficients of variation decrease for all automated respiratory cycle parameters in all infants. "t" values from ventilator respiratory cycle data are two to three times higher than ventilator respiratory cycles. Automated selection is highly specific. Automated respiratory cycle reflects most the interaction of both ventilator and patient. Improving discriminating power of ventilator monitoring will likely help in assessing disease status and following trends. Averaged parameters derived from automated respiratory cycles are more precise and could be displayed by ventilators to improve real-time fine tuning of ventilator settings.

An attributional life cycle assessment for an Italian residential multifamily building.

PubMed

Vitale, Pierluca; Arena, Umberto

2017-09-06

The study describes an attributional life cycle assessment carried out according to the ISO standards and focused on an Italian multifamily residential building. The aim was developing an exhaustive and reliable inventory of high-quality primary data, comparing the environmental impacts along the three stages of the building life cycle. The pre-use phase takes into account the production of all the construction materials, transportation, and on-site assembling. The use phase quantifies the resource consumptions for 50 years of the building utilization and ordinary maintenance. The end-of-life phase includes the building demolition and the management of generated wastes. The results quantify how the design criteria affect the environmental performances of the residential building along its life cycle. The role of the pre-use phase appears remarkable for global warming potential (GWP), due to the huge impacts of steel and concrete production processes. The use phase gives the largest contributions, which reach 77% and 84% of the total, for the categories of global warming and non-renewable energy. The end-of-life phase provides limited avoided impacts. A comparative analysis quantifies the improvements achievable with an alternative type of partitions and external walls. Acronyms: AC: air conditioning; C&DW: construction and demolition waste; CFL: compact fluorescent lamp; DHW: domestic hot water; EC: European Commission; EU: European Union; GDP: gross domestic product; GHG: greenhouse gases; GWP: global warming potential; LCA: life cycle assessment; LCI: life cycle inventory; LCIA: life cycle impact assessment; MFA: material flow analysis; NREP: non-renewable energy potential; RINP: respiratory inorganics potential; WFD: Waste Framework Directive.

Internal cycle modeling and environmental assessment of multiple cycle consumer products.

PubMed

Tsiliyannis, C A

2012-01-01

Dynamic annual flow models incorporating consumer discard and usage loss and featuring deterministic and stochastic end-of-cycle (EOC) return by the consumer are developed for reused or remanufactured products (multiple cycle products, MCPs), including fast and slow cycling, short and long-lived products. It is shown that internal flows (reuse and overall consumption) increase proportionally to the dimensionless internal cycle factor (ICF) which is related to environmental impact reduction factors. The combined reuse/recycle (or cycle) rate is shown capable for shortcut, albeit effective, monitoring of environmental performance in terms of waste production, virgin material extraction and manufacturing impacts of all MCPs, a task, which physical variables (lifetime, cycling frequency, mean or total number of return trips) and conventional rates, via which environmental policy has been officially implemented (e.g. recycling rate) cannot accomplish. The cycle rate is shown to be an increasing (hyperbolic) function of ICF. The impact of the stochastic EOC return characteristics on total reuse and consumption flows, as well as on eco-performance, is assessed: symmetric EOC return has a small, positive effect on performance compared to deterministic, while early shifted EOC return is more beneficial. In order to be efficient, environmental policy should set higher minimum reuse targets for higher trippage MCPs. The results may serve for monitoring, flow accounting and comparative eco-assessment of MCPs. They may be useful in identifying reachable and efficient reuse/recycle targets for consumer products and in planning return via appropriate labelling and digital coding for enhancing environmental performance, while satisfying consumer demand. Copyright © 2011 Elsevier Ltd. All rights reserved.

The life cycle assessment of alternative fuel chains for urban buses and trolleybuses.

PubMed

Kliucininkas, L; Matulevicius, J; Martuzevicius, D

2012-05-30

This paper describes a comparative analysis of public transport alternatives in the city of Kaunas, Lithuania. An LCA (Life Cycle Assessment) inventory analysis of fuel chains was undertaken using the midi urban bus and a similar type of trolleybus. The inventory analysis of fuel chains followed the guidelines provided by the ISO 14040 and ISO 14044 standards. The ReCiPe Life Cycle Impact Assessment (LCIA) methodology was used to quantify weighted damage originating from five alternative fuel chains. The compressed biogas fuel chain had the lowest weighted damage value, namely 45.7 mPt/km, whereas weighted damage values of the fuel chains based on electricity generation for trolleybuses were 60.6 mPt/km (for natural gas) and 78.9 mPt/km (for heavy fuel oil). The diesel and compressed natural gas fuel chains exhibited considerably higher damage values of 114.2 mPt/km and 132.6 mPt/km, respectively. The comparative life cycle assessment of fuel chains suggested that biogas-powered buses and electric trolleybuses can be considered as the best alternatives to use when modernizing the public transport fleet in Kaunas. Copyright © 2012 Elsevier Ltd. All rights reserved.

Efficacy and safety of the contraceptive vaginal ring (NuvaRing) compared with a combined oral contraceptive in Chinese women: a 1-year randomised trial.

PubMed

Fan, Guang Sheng; Ren, Mulan; Di, Wen; Su, Ping; Chang, Qin; Wu, Shuying; Qin, Yun; Korver, Tjeerd; Marintcheva-Petrova, Maya; Yacik, Carol; McCrary Sisk, Christine; Wang, Guoqin

2016-08-01

The aim of the study was to assess the efficacy and tolerability of the monthly vaginal ring (NuvaRing; 15 μg ethinylestradiol [EE] and 120 μg etonogestrel per day) compared with a monophasic (21/7) combined oral contraceptive (COC) containing 30 μg EE and 3 mg drospirenone in healthy Chinese women aged 18-40 years. This was a phase III, open-label, randomised multicentre trial conducted in China. Participants received NuvaRing or COC for 13 cycles (3 weeks of ring/pill treatment followed by a 1-week ring-free/pill-free period). Contraceptive efficacy was assessed by in-treatment pregnancies and expressed by the Pearl Index (PI; number of pregnancies/100 woman-years of use). Cycle control was assessed by unscheduled (breakthrough) and absence of scheduled (withdrawal) bleeding events. Safety and tolerability were assessed throughout the study. Participants were randomised either to the NuvaRing (n = 732) or to the COC (n = 214); 588 (82.4%) and 182 (78.4%) participants, respectively, completed the study. There were 10 in-treatment pregnancies in the NuvaRing group (PI 1.92; 95% confidence interval [CI] 0.92, 3.53) and five in the COC group (PI 3.12; 95% CI 1.01, 7.29). Breakthrough bleeding/spotting ranged from 18.6% (Cycle 1) to 4.2% (Cycle 11) for NuvaRing and from 21.6% (Cycle 1) to 7.9% (Cycle 11) for COC. Absence of withdrawal bleeding ranged from 8.6% (Cycle 1) to 3.0% (Cycle 11) for NuvaRing and from 14.6% (Cycle 1) to 6.4% (Cycle 5) for COC. For NuvaRing and COC, respectively, 26.6% and 25.0% of participants had treatment-related adverse events, and 7.0% and 9.1% discontinued the study as a result. Once-monthly NuvaRing is efficacious and safe for use in Chinese women.

Evaluation of staff performance and interpretation of the screening program for prevention of thalassemia.

PubMed

Prommetta, Simaporn; Sanchaisuriya, Kanokwan; Fucharoen, Goonnapa; Yamsri, Supawadee; Chaiboonroeng, Attawut; Fucharoen, Supan

2017-06-15

Thalassemia screening program has been implemented for years in Southeast Asia, but no external quality assessment program has been established. We have developed and initiated the proficiency testing (PT) program for the first time in Thailand with the aim to assess the screening performance of laboratory staff and their competency in interpretation of the screening results. Three PT cycles per year were organized. From the first to the third cycle of the PT scheme, a total number of participant laboratories increased from 59 to 67. In each cycle, 2 PT items (assigned as blood samples of the couple) were provided. Performance evaluation was based on the accuracy of screening results, i.e . mean corpuscular volume (MCV), mean corpuscular haemoglobin (MCH) and the dichlorophenolindophenol (DCIP) test for haemoglobin E, including the competency in interpretation of screening results and assessment of foetal risk. Performance was assessed by comparing the participants' result against the assigned value. Of all 3 cycles, most laboratories reported acceptable MCV and MCH values. From the first to the third cycle, incorrect DCIP test and misinterpretation rates were decreased while incorrect risk assessment varied by cycle to cycle. Combining the accuracy of thalassemia screening and the competency in interpretation and risk assessment, approximately half of participants showed excellent performance. Improved performance observed in many laboratories reflects the achievement and benefit of the PT program which should be regularly provided.

Improved access and cycle time with an "in-house" patient-centered teleglaucoma program versus traditional in-person assessment.

PubMed

Arora, Sourabh; Rudnisky, Chris J; Damji, Karim F

2014-05-01

To compare access time and cycle time between an "in-house" teleglaucoma program and in-person glaucoma consultation. This was a prospective comparative study of 71 patients seen through the teleglaucoma program (eligible patients were glaucoma suspects or early-stage open-angle glaucoma) and 63 patients seen via a traditional in-person exam with a physician present. Access time was calculated as the time from the patient being referred to the date of a booked visit for either a teleglaucoma or in-person exam. Cycle time was defined as the time from registration until departure during the visit to the hospital; it was calculated for the subset of patients from each study group who completed activity logs on the day of their visit. The mean access time was significantly shorter for patients seen through teleglaucoma compared with in-person exam: 45±22 days (range, 13-121 days) (n=68) versus 88±47 days (range, 27-214 days) (n=63), respectively (p<0.0001). The cycle time was also reduced for patients seen through teleglaucoma, compared with in-person assessment: 78±20 min (range, 40-130 min) (n=39) versus 115±44 min (range, 51-216 min) (n=39), respectively (p<0.001). The mean percentage time spent in the waiting room was also significantly reduced for patients seen through teleglaucoma versus in-person assessments: 19±13% versus 41±24% (n=39), respectively (p<0.01). Teleglaucoma improves access to care and is a more efficient way of managing glaucoma suspects and patients with early-stage glaucoma compared with in-person assessment.

Carbon-Carbon Recuperators in Closed-Brayton-Cycle Nuclear Space Power Systems: A Feasibility Assessment

NASA Technical Reports Server (NTRS)

Barrett, Michael J.; Johnson, Paul K.

2004-01-01

The feasibility of using carbon-carbon recuperators in closed-Brayton-cycle (CBC) nuclear space power conversion systems (PCS) was assessed. Recuperator performance expectations were forecast based on projected thermodynamic cycle state values for a planetary mission. Resulting thermal performance, mass and volume for a plate-fin carbon-carbon recuperator were estimated and quantitatively compared with values for a conventional offset-strip-fin metallic design. Material compatibility issues regarding carbon-carbon surfaces exposed to the working fluid in the CBC PCS were also discussed.

Benefits of advanced technology in industrial cogeneration

NASA Technical Reports Server (NTRS)

Barna, G. J.; Burns, R. K.

1979-01-01

This broad study is aimed at identifying the most attractive advanced energy conversion systems for industrial cogeneration for the 1985 to 2000 time period and assessing the advantages of advanced technology systems compared to using today's commercially available technology. Energy conversion systems being studied include those using steam turbines, open cycle gas turbines, combined cycles, diesel engines, Stirling engines, closed cycle gas turbines, phosphoric acid and molten carbonate fuel cells and thermionics. Specific cases using today's commercially available technology are being included to serve as a baseline for assessing the advantages of advanced technology.

Air pollution as a risk factor in health impact assessments of a travel mode shift towards cycling

PubMed Central

Raza, Wasif; Forsberg, Bertil; Johansson, Christer; Sommar, Johan Nilsson

2018-01-01

ABSTRACT Background: Promotion of active commuting provides substantial health and environmental benefits by influencing air pollution, physical activity, accidents, and noise. However, studies evaluating intervention and policies on a mode shift from motorized transport to cycling have estimated health impacts with varying validity and precision. Objective: To review and discuss the estimation of air pollution exposure and its impacts in health impact assessment studies of a shift in transport from cars to bicycles in order to guide future assessments. Methods: A systematic database search of PubMed was done primarily for articles published from January 2000 to May 2016 according to PRISMA guidelines. Results: We identified 18 studies of health impact assessment of change in transport mode. Most studies investigated future hypothetical scenarios of increased cycling. The impact on the general population was estimated using a comparative risk assessment approach in the majority of these studies, whereas some used previously published cost estimates. Air pollution exposure during cycling was estimated based on the ventilation rate, the pollutant concentration, and the trip duration. Most studies employed exposure-response functions from studies comparing background levels of fine particles between cities to estimate the health impacts of local traffic emissions. The effect of air pollution associated with increased cycling contributed small health benefits for the general population, and also only slightly increased risks associated with fine particle exposure among those who shifted to cycling. However, studies calculating health impacts based on exposure-response functions for ozone, black carbon or nitrogen oxides found larger effects attributed to changes in air pollution exposure. Conclusion: A large discrepancy between studies was observed due to different health impact assessment approaches, different assumptions for calculation of inhaled dose and different selection of dose-response functions. This kind of assessments would improve from more holistic approaches using more specific exposure-response functions. PMID:29400262

Enhancement of life cycle assessment (LCA) methodology to include the effect of surface albedo on climate change: Comparing black and white roofs.

PubMed

Susca, Tiziana

2012-04-01

Traditionally, life cycle assessment (LCA) does not estimate a key property: surface albedo. Here an enhancement of the LCA methodology has been proposed through the development and employment of a time-dependent climatological model for including the effect of surface albedo on climate. The theoretical findings derived by the time-dependent model have been applied to the case study of a black and a white roof evaluated in the time-frames of 50 and 100 years focusing on the impact on global warming potential. The comparative life cycle impact assessment of the two roofs shows that the high surface albedo plays a crucial role in offsetting radiative forcings. In the 50-year time horizon, surface albedo is responsible for a decrease in CO(2)eq of 110-184 kg and 131-217 kg in 100 years. Furthermore, the white roof compared to the black roof, due to the high albedo, decreases the annual energy use of about 3.6-4.5 kWh/m(2). Copyright © 2011 Elsevier Ltd. All rights reserved.

Using Screening Level Environmental Life Cycle Assessment to Aid Decision Making: A Case Study of a College Annual Report

ERIC Educational Resources Information Center

Ingwersen, Wesley W.; Curran, Mary Ann; Gonzalez, Michael A.; Hawkins, Troy R.

2012-01-01

Purpose: The purpose of this study is to compare the life cycle environmental impacts of the University of Cincinnati College of Engineering and Applied Sciences' current printed annual report to a version distributed via the internet. Design/methodology/approach: Life cycle environmental impacts of both versions of the report are modeled using…

Cradle-to-gate life cycle assessment of composite I-joists produced in the southeast region of the United States

Treesearch

Richard D. Bergman; Sevda Alanya-Rosenbaum

2017-01-01

The goal of this study was to update life-cycle assessment (LCA) data on I-joist production in the southeast (SE) region of the United States. The authors collected primary mill data from I-joist production facilities per Consortium on Research for Renewable Industrial Materials (CORRIM) research guidelines. Comparative assertions were not a goal of this study.

Internal cycle modeling and environmental assessment of multiple cycle consumer products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsiliyannis, C.A., E-mail: anion@otenet.gr

2012-01-15

Highlights: Black-Right-Pointing-Pointer Dynamic flow models are presented for remanufactured, reused or recycled products. Black-Right-Pointing-Pointer Early loss and stochastic return are included for fast and slow cycling products. Black-Right-Pointing-Pointer The reuse-to-input flow ratio (Internal Cycle Factor, ICF) is determined. Black-Right-Pointing-Pointer The cycle rate, which is increasing with the ICF, monitors eco-performance. Black-Right-Pointing-Pointer Early internal cycle losses diminish the ICF, the cycle rate and performance. - Abstract: Dynamic annual flow models incorporating consumer discard and usage loss and featuring deterministic and stochastic end-of-cycle (EOC) return by the consumer are developed for reused or remanufactured products (multiple cycle products, MCPs), including fast andmore » slow cycling, short and long-lived products. It is shown that internal flows (reuse and overall consumption) increase proportionally to the dimensionless internal cycle factor (ICF) which is related to environmental impact reduction factors. The combined reuse/recycle (or cycle) rate is shown capable for shortcut, albeit effective, monitoring of environmental performance in terms of waste production, virgin material extraction and manufacturing impacts of all MCPs, a task, which physical variables (lifetime, cycling frequency, mean or total number of return trips) and conventional rates, via which environmental policy has been officially implemented (e.g. recycling rate) cannot accomplish. The cycle rate is shown to be an increasing (hyperbolic) function of ICF. The impact of the stochastic EOC return characteristics on total reuse and consumption flows, as well as on eco-performance, is assessed: symmetric EOC return has a small, positive effect on performance compared to deterministic, while early shifted EOC return is more beneficial. In order to be efficient, environmental policy should set higher minimum reuse targets for higher trippage MCPs. The results may serve for monitoring, flow accounting and comparative eco-assessment of MCPs. They may be useful in identifying reachable and efficient reuse/recycle targets for consumer products and in planning return via appropriate labelling and digital coding for enhancing environmental performance, while satisfying consumer demand.« less

Is there an environmental benefit from remediation of a contaminated site? Combined assessments of the risk reduction and life cycle impact of remediation.

PubMed

Lemming, Gitte; Chambon, Julie C; Binning, Philip J; Bjerg, Poul L

2012-12-15

A comparative life cycle assessment is presented for four different management options for a trichloroethene-contaminated site with a contaminant source zone located in a fractured clay till. The compared options are (i) long-term monitoring (ii) in-situ enhanced reductive dechlorination (ERD), (iii) in-situ chemical oxidation (ISCO) with permanganate and (iv) long-term monitoring combined with treatment by activated carbon at the nearby waterworks. The life cycle assessment included evaluation of both primary and secondary environmental impacts. The primary impacts are the local human toxic impacts due to contaminant leaching into groundwater that is used for drinking water, whereas the secondary environmental impacts are related to remediation activities such as monitoring, drilling and construction of wells and use of remedial amendments. The primary impacts for the compared scenarios were determined by a numerical risk assessment and remedial performance model, which predicted the contaminant mass discharge over time at a point of compliance in the aquifer and at the waterworks. The combined assessment of risk reduction and life cycle impacts showed that all management options result in higher environmental impacts than they remediate, in terms of person equivalents and assuming equal weighting of all impacts. The ERD and long-term monitoring were the scenarios with the lowest secondary life cycle impacts and are therefore the preferred alternatives. However, if activated carbon treatment at the waterworks is required in the long-term monitoring scenario, then it becomes unfavorable because of large secondary impacts. ERD is favorable due to its low secondary impacts, but only if leaching of vinyl chloride to the groundwater aquifer can be avoided. Remediation with ISCO caused the highest secondary impacts and cannot be recommended for the site. Copyright © 2012 Elsevier Ltd. All rights reserved.

Life Cycle Comparison of Waste-to-Energy to Sanitary Landfill

EPA Science Inventory

Life cycle assessment (LCA) can be used to evaluate the environmental footprint of products, processes, and services. An LCA allows decision makers to compare products and processes through systematic evaluation of supply chains. Also known as a “cradle-to-grave” approach, LCA ev...

Development of a new assessment tool for cervical myelopathy using hand-tracking sensor: Part 1: validity and reliability.

PubMed

Alagha, M Abdulhadi; Alagha, Mahmoud A; Dunstan, Eleanor; Sperwer, Olaf; Timmins, Kate A; Boszczyk, Bronek M

2017-04-01

To assess the reliability and validity of a hand motion sensor, Leap Motion Controller (LMC), in the 15-s hand grip-and-release test, as compared against human inspection of an external digital camera recording. Fifty healthy participants were asked to fully grip-and-release their dominant hand as rapidly as possible for two trials with a 10-min rest in-between, while wearing a non-metal wrist splint. Each test lasted for 15 s, and a digital camera was used to film the anterolateral side of the hand on the first test. Three assessors counted the frequency of grip-and-release (G-R) cycles independently and in a blinded fashion. The average mean of the three was compared with that measured by LMC using the Bland-Altman method. Test-retest reliability was examined by comparing the two 15-s tests. The mean number of G-R cycles recorded was: 47.8 ± 6.4 (test 1, video observer); 47.7 ± 6.5 (test 1, LMC); and 50.2 ± 6.5 (test 2, LMC). Bland-Altman indicated good agreement, with a low bias (0.15 cycles) and narrow limits of agreement. The ICC showed high inter-rater agreement and the coefficient of repeatability for the number of cycles was ±5.393, with a mean bias of 3.63. LMC appears to be valid and reliable in the 15-s grip-and-release test. This serves as a first step towards the development of an objective myelopathy assessment device and platform for the assessment of neuromotor hand function in general. Further assessment in a clinical setting and to gauge healthy benchmark values is warranted.

Influence of driving cycles on unit emissions from passenger cars

NASA Astrophysics Data System (ADS)

Joumard, R.; André, M.; Vidon, R.; Tassel, P.; Pruvost, C.

Small samples of petrol engine or diesel cars, equipped with or without catalysts, were tested over 36 driving cycles divided into four categories - standard cycles and three sets of cycles more representative of real-world driving conditions. The tests addressed standard gaseous pollutants and fuel consumption and also less frequently measured pollutant such as CH 4. In the first part of this paper we examine cold emissions in order to assess the duration of the cold start impact and the representativity of the cold ECE15 cycle. Then unit emissions are compared over the four driving cycle families. As compared to representative cycles, the standardised cycles underestimate hot emissions by almost 50% for petrol engine cars and 30% for diesel vehicles. Conversely, the results obtained for the three representative cycle families are in relatively close agreement with each other - within approximately 10%. However, the cinematic properties of the three families differ. Finally, we demonstrate that weighting all emission data equally, not taking into account the weight of each cycle in overall traffic, introduces significant biases, particularly when plotting emission vs. average speed curves.

[Life cycle assessment of energy consumption and greenhouse gas emissions of cellulosic ethanol from corn stover].

PubMed

Tian, Wang; Liao, Cuiping; Li, Li; Zhao, Daiqing

2011-03-01

Life Cycle Assessment (LCA) is the only standardized tool currently used to assess environmental loads of products and processes. The life cycle analysis, as a part of LCA, is a useful and powerful methodology for studying life cycle energy efficiency and life cycle GHG emission. To quantitatively explain the potential of energy saving and greenhouse gas (GHG) emissions reduction of corn stover-based ethanol, we analyzed life cycle energy consumption and GHG emissions of corn stover-based ethanol by the method of life cycle analysis. The processes are dilute acid prehydrolysis and enzymatic hydrolysis. The functional unit was defined as 1 km distance driven by the vehicle. Results indicated: compared with gasoline, the corn stover-based E100 (100% ethanol) and E10 (a blend of 10% ethanol and 90% gasoline by volume) could reduce life cycle fossil energy consumption by 79.63% and 6.25% respectively, as well as GHG emissions by 53.98% and 6.69%; the fossil energy consumed by biomass stage was 68.3% of total fossil energy input, N-fertilizer and diesel were the main factors which contributed 45.78% and 33.26% to biomass stage; electricity production process contributed 42.06% to the net GHG emissions, the improvement of technology might reduce emissions markedly.

A Comparative Life Cycle Assessment of Recycling the Platinum Group Metals from Automobile Catalytic Converter: An Australian Perspective

NASA Astrophysics Data System (ADS)

Ghodrat, Maryam; Rhamdhani, M. Akbar; Sharafi, Pezhman; Samali, Bijan

2017-12-01

This study provides a comparison between environmental impacts of the recovery of platinum group metals (PGMs) from the end-of-life catalytic converters by hydrometallurgical and pyrometallurgical methods. A gate to grave life cycle assessment of a typical three-way catalytic converter manufactured for an Australian passenger car was carried out using GaBi professional environmental package. Recovery rates, as well as qualities, quantities, losses, and fugitive emissions for all materials and elements used in both methods were calculated based on the developed flowsheets. A life cycle impact assessment was then made by carrying out a mass balance calculation. Inventory data show that the hydrometallurgical route for recycling of the platinum group metals out of catalytic converter scrap has lower impacts on the environment compared with the pyrometallurgical method. In terms of emission effects, the hydrometallurgical process was found to be highly advantageous since it causes insignificant emissions to air, sea water, and fresh water. It is also found that the hydrometallurgical route performs comparatively superior in terms of acidification, eutrophication, fossil depletion, and human toxicity. The obtained results are applicable only to the Australian setting.

Improving the Comparability and Local Usefulness of International Assessments: A Look Back and a Way Forward

ERIC Educational Resources Information Center

Rutkowski, Leslie; Rutkowski, David

2018-01-01

Over time international large-scale assessments have grown in terms of number of studies, cycles, and participating countries, many of which are a heterogeneous mix of economies, languages, cultures, and geography. This heterogeneity has meaningful consequences for comparably measuring both achievement and non-achievement constructs, such as…

Studies on the Growth Effects of the Canaline-Urea Cycle Amino Acids with Lemna minor L. 1

PubMed Central

Rosenthal, Gerald A.; Gulati, Dushyant K.; Sabharwal, P. S.

1975-01-01

The aquatic microphyte, Lemna minor L., was utilized to assess the relative toxicity and general growth effects of canavanine, canaline, ureidohomoserine (UHS), and canavaninosuccinate (CSA). These amino acids are constituents of the canaline-urea cycle and structural analogues of the ornithine-urea cycle amino acids. Comparative growth studies with L. minor revealed that the canaline-urea cycle amino acids are potent antimetabolites. With the exception of CSA, they are extremely toxic at a concentration of 5 μm. Over a concentration range of 1 to 4 μm, canavanine is the most growth-inhibiting of the canaline-urea cycle amino acids. At or above 5 μm, canavanine and canaline possess comparable toxicity. UHS is less growth-inhibiting than canavanine or canaline, and CSA is the least toxic of the canaline-urea cycle intermediates. PMID:16659316

Life cycle assessment of metal alloys for structural applications

NASA Astrophysics Data System (ADS)

Malovrh Rebec, K.; Markoli, B.; Leskovar, B.

2018-03-01

The study compared environmental footprints of two types of Al-alloys: well-known 5083 aluminium alloy with magnesium and traces of manganese and chromium in its composition. This material is highly resistant to seawater corrosion and the influence of industrial chemicals. Furthermore, it retains exceptional strength after welding. The comparisons were made to an innovative alloy where the aluminium based matrix is reinforced by metastable quasicrystals (QC), thus avoiding magnesium in its composition. Furthermore, we checked other aluminium ingots’ footprints and compared European average and Germany country specific production data. Environmental footprints were assessed via cradle to gate life cycle assessment. Our findings normalized to 1 m2 plate suggest, that newly proposed alloy could save around 50 % in value of parameters abiotic resources depletion of fossil fuels, acidification, eutrophication, global warming potential and photochemical ozone creation potential if we compare Qc5 to 6 mm 5083 alloy plate. Only abiotic resources depletion of elements and ozone depletion parameters increase for Qc5 compared to 6 mm 5083 alloy plate.

Power systems for future missions

NASA Technical Reports Server (NTRS)

Gill, S. P.; Frye, P. E.; Littman, Franklin D.; Meisl, C. J.

1994-01-01

A comprehensive scenario of future missions was developed and applicability of different power technologies to these missions was assessed. Detailed technology development roadmaps for selected power technologies were generated. A simple methodology to evaluate economic benefits of current and future power system technologies by comparing Life Cycle Costs of potential missions was developed. The methodology was demonstrated by comparing Life Cycle Costs for different implementation strategies of DIPS/CBC technology to a selected set of missions.

Environmental performance of green building code and certification systems.

PubMed

Suh, Sangwon; Tomar, Shivira; Leighton, Matthew; Kneifel, Joshua

2014-01-01

We examined the potential life-cycle environmental impact reduction of three green building code and certification (GBCC) systems: LEED, ASHRAE 189.1, and IgCC. A recently completed whole-building life cycle assessment (LCA) database of NIST was applied to a prototype building model specification by NREL. TRACI 2.0 of EPA was used for life cycle impact assessment (LCIA). The results showed that the baseline building model generates about 18 thousand metric tons CO2-equiv. of greenhouse gases (GHGs) and consumes 6 terajoule (TJ) of primary energy and 328 million liter of water over its life-cycle. Overall, GBCC-compliant building models generated 0% to 25% less environmental impacts than the baseline case (average 14% reduction). The largest reductions were associated with acidification (25%), human health-respiratory (24%), and global warming (GW) (22%), while no reductions were observed for ozone layer depletion (OD) and land use (LU). The performances of the three GBCC-compliant building models measured in life-cycle impact reduction were comparable. A sensitivity analysis showed that the comparative results were reasonably robust, although some results were relatively sensitive to the behavioral parameters, including employee transportation and purchased electricity during the occupancy phase (average sensitivity coefficients 0.26-0.29).

Secular pattern of aneurismal rupture with the lunar cycle and season.

PubMed

Banfield, Jillian C; Abdolell, Mohamed; Shankar, Jai S

2017-02-01

Background The lunar cycle and seasons may be associated with rates of rupture of intracranial aneurysms, but the literature is mixed. Studies of the association between the lunar cycle and rates of aneurysm rupture used the eight qualitative moon phases. The purpose of this study was to assess any association of aneurysm rupture with the lunar cycle and with the season. Materials and methods We retrospectively reviewed all cases of subarachnoid haemorrhage secondary to ruptured intracranial aneurysm treated with endovascular coiling in our institution over a 10-year period. We included only cases with a known rupture date. We used the degree of illumination of the moon to quantitatively code the lunar cycle. Results A total of 212 cases were included in our analyses. The odds of aneurysm rupture were significantly greater ( p < 0.001) when the moon was least (new moon) and most (full moon) illuminated, as compared to the middle of the lunar cycle. The odds of rupture tended to be higher ( p = 0.059) in the summer, compared to autumn. Conclusions The odds of aneurysm rupture were greater when the moon was least illuminated (new moon) and most illuminated (full moon), compared to the middle of the lunar cycle.

Active cycle of breathing technique for cystic fibrosis.

PubMed

Mckoy, Naomi A; Wilson, Lisa M; Saldanha, Ian J; Odelola, Olaide A; Robinson, Karen A

2016-07-05

People with cystic fibrosis experience chronic airway infections as a result of mucus build up within the lungs. Repeated infections often cause lung damage and disease. Airway clearance therapies aim to improve mucus clearance, increase sputum production, and improve airway function. The active cycle of breathing technique (also known as ACBT) is an airway clearance method that uses a cycle of techniques to loosen airway secretions including breathing control, thoracic expansion exercises, and the forced expiration technique. This is an update of a previously published review. To compare the clinical effectiveness of the active cycle of breathing technique with other airway clearance therapies in cystic fibrosis. We searched the Cochrane Cystic Fibrosis Trials Register, compiled from electronic database searches and handsearching of journals and conference abstract books. We also searched the reference lists of relevant articles and reviews.Date of last search: 25 April 2016. Randomised or quasi-randomised controlled clinical studies, including cross-over studies, comparing the active cycle of breathing technique with other airway clearance therapies in cystic fibrosis. Two review authors independently screened each article, abstracted data and assessed the risk of bias of each study. Our search identified 62 studies, of which 19 (440 participants) met the inclusion criteria. Five randomised controlled studies (192 participants) were included in the meta-analysis; three were of cross-over design. The 14 remaining studies were cross-over studies with inadequate reports for complete assessment. The study size ranged from seven to 65 participants. The age of the participants ranged from six to 63 years (mean age 22.33 years). In 13 studies, follow up lasted a single day. However, there were two long-term randomised controlled studies with follow up of one to three years. Most of the studies did not report on key quality items, and therefore, have an unclear risk of bias in terms of random sequence generation, allocation concealment, and outcome assessor blinding. Due to the nature of the intervention, none of the studies blinded participants or the personnel applying the interventions. However, most of the studies reported on all planned outcomes, had adequate follow up, assessed compliance, and used an intention-to-treat analysis.Included studies compared the active cycle of breathing technique with autogenic drainage, airway oscillating devices, high frequency chest compression devices, conventional chest physiotherapy, and positive expiratory pressure. Preference of technique varied: more participants preferred autogenic drainage over the active cycle of breathing technique; more preferred the active cycle of breathing technique over airway oscillating devices; and more were comfortable with the active cycle of breathing technique versus high frequency chest compression. No significant difference was seen in quality of life, sputum weight, exercise tolerance, lung function, or oxygen saturation between the active cycle of breathing technique and autogenic drainage or between the active cycle of breathing technique and airway oscillating devices. There was no significant difference in lung function and the number of pulmonary exacerbations between the active cycle of breathing technique alone or in conjunction with conventional chest physiotherapy. All other outcomes were either not measured or had insufficient data for analysis. There is insufficient evidence to support or reject the use of the active cycle of breathing technique over any other airway clearance therapy. Five studies, with data from eight different comparators, found that the active cycle of breathing technique was comparable with other therapies in outcomes such as participant preference, quality of life, exercise tolerance, lung function, sputum weight, oxygen saturation, and number of pulmonary exacerbations. Longer-term studies are needed to more adequately assess the effects of the active cycle of breathing technique on outcomes important for people with cystic fibrosis such as quality of life and preference.

A Comparative Analysis of Life-Cycle Assessment Tools for ...

EPA Pesticide Factsheets

We identified and evaluated five life-cycle assessment tools that community decision makers can use to assess the environmental and economic impacts of end-of-life (EOL) materials management options. The tools evaluated in this report are waste reduction mode (WARM), municipal solid waste-decision support tool (MSW-DST), solid waste optimization life-cycle framework (SWOLF), environmental assessment system for environmental technologies (EASETECH), and waste and resources assessment for the environment (WRATE). WARM, MSW-DST, and SWOLF were developed for US-specific materials management strategies, while WRATE and EASETECH were developed for European-specific conditions. All of the tools (with the exception of WARM) allow specification of a wide variety of parameters (e.g., materials composition and energy mix) to a varying degree, thus allowing users to model specific EOL materials management methods even outside the geographical domain they are originally intended for. The flexibility to accept user-specified input for a large number of parameters increases the level of complexity and the skill set needed for using these tools. The tools were evaluated and compared based on a series of criteria, including general tool features, the scope of the analysis (e.g., materials and processes included), and the impact categories analyzed (e.g., climate change, acidification). A series of scenarios representing materials management problems currently relevant to c

Using screening level environmental life cycle assessment to aid decision making: A case study of a college annual report

EPA Science Inventory

Purpose – In this study we compare the life cycle environmental impacts of the University of Cincinnati College of Engineering and Applied Sciences’ current printed annual report to a version distributed via the Internet. This case study demonstrates how a screening level life cy...

Measuring Age-Dependent Myocardial Stiffness across the Cardiac Cycle using MR Elastography: A Reproducibility Study

PubMed Central

Wassenaar, Peter A; Eleswarpu, Chethanya N; Schroeder, Samuel A; Mo, Xiaokui; Raterman, Brian D; White, Richard D; Kolipaka, Arunark

2015-01-01

Purpose To assess reproducibility in measuring left ventricular (LV) myocardial stiffness in volunteers throughout the cardiac cycle using magnetic resonance elastography (MRE) and to determine its correlation with age. Methods Cardiac MRE (CMRE) was performed on 29 normal volunteers, with ages ranging from 21 to 73 years. For assessing reproducibility of CMRE-derived stiffness measurements, scans were repeated per volunteer. Wave images were acquired throughout the LV myocardium, and were analyzed to obtain mean stiffness during the cardiac cycle. CMRE-derived stiffness values were correlated to age. Results Concordance correlation coefficient revealed good inter-scan agreement with rc of 0.77, with p-value<0.0001. Significantly higher myocardial stiffness was observed during end-systole (ES) compared to end-diastole (ED) across all subjects. Additionally, increased deviation between ES and ED stiffness was observed with increased age. Conclusion CMRE-derived stiffness is reproducible, with myocardial stiffness changing cyclically across the cardiac cycle. Stiffness is significantly higher during ES compared to ED. With age, ES myocardial stiffness increases more than ED, giving rise to an increased deviation between the two. PMID:26010456

Selection of euploid blastocysts for cryopreservation with array comparative genomic hybridization (aCGH) results in increased implantation rates in subsequent frozen and thawed embryo transfer cycles

PubMed Central

2013-01-01

Background In assisted reproductive treatments, embryos remaining after fresh embryo transfer are usually selected for cryopreservation based on traditional morphology assessment. Our previous report has demonstrated that array comparative genomic hybridization (aCGH) screening for IVF patients with good prognosis significantly improves clinical and ongoing pregnancy rates in fresh embryo transfer cycles. The current study further investigates the efficiency of applying aCGH in the selection of euploid embryos for cryopreservation as related to pregnancy and implantation outcomes in subsequent frozen embryo transfer (FET) cycles. Methods First-time IVF patients with good prognosis undergoing fresh single embryo transfer and having at least one remaining blastocyst for cryopreservation were prospectively randomized into two groups: 1) Group A patients had embryos assessed by morphology first and then by aCGH screening of trophectoderm cells and 2) Group B patients had embryos evaluated by morphology alone. All patients had at least one blastocyst available for cryopreservation after fresh embryo transfer. There were 15 patients in Group A and 23 patients in Group B who failed to conceive after fresh embryo transfer and completed the FET cycles. Blastocyst survival and implantation rates were compared between the two groups. Results There were no significant differences in blastocyst survival rates between Group A and Group B (90.9% vs. 91.3%, respectively; p >0.05). However, a significantly higher implantation rate was observed in the morphology assessment plus aCGH screening group compared to the morphology assessment alone group (65.0% vs. 33.3%, respectively; p = 0.038). There was no miscarriage observed in Group A while a 16.7% miscarriage rate was recorded in Group B (0% vs. 16.7%, respectively; p >0.05). Conclusions While aCGH screening has been recently applied to select euploid blastocysts for fresh transfer in young, low-risk IVF patients, this is the first prospective study on the impact of aCGH specifically on blastocyst survival and implantation outcomes in the subsequent FET cycles of IVF patients with good prognosis. The present study demonstrates that aCGH screening of blastocysts prior to cryopreservation significantly improves implantation rates and may reduce the risk of miscarriage in subsequent FET cycles. Further randomized clinical studies with a larger sample size are needed to validate these preliminary findings. PMID:23937723

Technological and life cycle assessment of organics processing odour control technologies.

PubMed

Bindra, Navin; Dubey, Brajesh; Dutta, Animesh

2015-09-15

As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. Copyright © 2015 Elsevier B.V. All rights reserved.

Intergenerational considerations affecting the future of nuclear power: equity as a framework for assessing fuel cycles.

PubMed

Taebi, Behnam; Kadak, Andrew C

2010-09-01

Alternative fuel cycles are being considered in an effort to prolong uranium fuel supplies for thousands of years to come and to manage nuclear waste. These strategies bring with them different benefits and burdens for the present generation and for future generations. In this article, we present a method that provides insight into future fuel cycle alternatives and into the conflicts arising between generations within the framework of intergenerational equity. A set of intersubjective values is drawn from the notion of sustainable development. By operationalizing these values and mapping out their impacts, value criteria are introduced for the assessment of fuel cycles, which are based on the distribution of burdens and benefits between generations. The once-through fuel cycle currently deployed in the United States and three future fuel cycles are subsequently assessed according to these criteria. The four alternatives are then compared in an integrated analysis in which we shed light on the implicit tradeoffs made by decisionmakers when they choose a certain fuel cycle. When choosing a fuel cycle, what are the societal costs and burdens accepted for each generation and how can these factors be justified? This article presents an integrated decision-making method, which considers intergenerational aspects of such decisions; this method could also be applied to other technologies. © 2010 Society for Risk Analysis.

The association between commuter cycling and sickness absence.

PubMed

Hendriksen, Ingrid J M; Simons, Monique; Garre, Francisca Galindo; Hildebrandt, Vincent H

2010-08-01

To study the association between commuter cycling and all-cause sickness absence, and the possible dose-response relationship between absenteeism and the distance, frequency and speed of commuter cycling. Cross-sectional data about cycling in 1236 Dutch employees were collected using a self-report questionnaire. Company absenteeism records were checked over a one-year period (May 2007-April 2008). Propensity scores were used to make groups comparable and to adjust for confounders. Zero-inflated Poisson models were used to assess differences in absenteeism between cyclists and non-cyclists. The mean total duration of absenteeism over the study year was more than 1 day shorter in cyclists than in non-cyclists. This can be explained by the higher proportion of people with no absenteeism in the cycling group. A dose-response relationship was observed between the speed and distance of cycling and absenteeism. Compared to people who cycle a short distance (

COMPARISON OF TRUNK AND LOWER EXTREMITY MUSCLE ACTIVITY AMONG FOUR STATIONARY EQUIPMENT DEVICES: UPRIGHT BIKE, RECUMBENT BIKE, TREADMILL, AND ELLIPTIGO®

PubMed Central

Baker, Ryan; Gibson, Chris; Kearney, Andrew; Busemeyer, Tommy

2016-01-01

Background Stationary equipment devices are often used to improve fitness. The ElliptiGO® was recently developed that blends the elements of an elliptical trainer and bicycle, allowing reciprocal lower limb pedaling in an upright position. However, it is unknown whether the muscle activity used for the ElliptiGO® is similar to walking or cycling. To date, there is no information comparing muscle activity for exercise on the treadmill, stationary upright and recumbent bikes, and the ElliptiGO®. Purpose/Hypothesis The purpose of this study was to assess trunk and lower extremity muscle activity among treadmill walking, cycling (recumbent and upright) and the ElliptiGO® cycling. It was hypothesized that the ElliptiGO® and treadmill would elicit similar electromyographic muscle activity responses compared to the stationary bike and recumbent bike during an exercise session. Study Design Cohort, repeated measures Methods Twelve recreationally active volunteers participated in the study and were assigned a random order of exercise for each of the four devices (ElliptiGO®, stationary upright cycle ergometer, recumbent ergometer, and a treadmill). Two-dimensional video was used to monitor the start and stop of exercise and surface electromyography (SEMG) were used to assess muscle activity during two minutes of cycling or treadmill walking at 40-50% heart rate reserve (HRR). Eight muscles on the dominant limb were used for analysis: gluteus maximus (Gmax), gluteus medius (Gmed), biceps femoris (BF), lateral head of the gastrocnemius (LG), tibialis anterior (TA), rectus femoris (RF). Two trunk muscles were assessed on the same side; lumbar erector spinae at L3-4 level (LES) and rectus abdominus (RA). Maximal voluntary isometric contractions (MVIC) were determined for each muscle and SEMG data were expressed as %MVIC in order to normalize outputs. Results The %MVIC for RF during ElliptiGO® cycling was higher than recumbent cycling. The LG muscle activity was highest during upright cycling. The TA was higher during walking compared to recumbent cycling and ElliptiGO® cycling. No differences were found among the the LES and remaining lower limb musculature across devices. Conclusion ElliptiGO® cycling was found to elicit sufficient muscle activity to provide a strengthening stimulus for the RF muscle. The LES, RA, Gmax, Gmed, and BF activity were similar across all devices and ranged from low to moderate strength levels of muscle activation. The information gained from this study may assist clinicians in developing low to moderate strengthening exercise protocols when using these four devices. Level of evidence 3 PMID:27104052

COMPARISON OF TRUNK AND LOWER EXTREMITY MUSCLE ACTIVITY AMONG FOUR STATIONARY EQUIPMENT DEVICES: UPRIGHT BIKE, RECUMBENT BIKE, TREADMILL, AND ELLIPTIGO®.

PubMed

Bouillon, Lucinda; Baker, Ryan; Gibson, Chris; Kearney, Andrew; Busemeyer, Tommy

2016-04-01

Stationary equipment devices are often used to improve fitness. The ElliptiGO® was recently developed that blends the elements of an elliptical trainer and bicycle, allowing reciprocal lower limb pedaling in an upright position. However, it is unknown whether the muscle activity used for the ElliptiGO® is similar to walking or cycling. To date, there is no information comparing muscle activity for exercise on the treadmill, stationary upright and recumbent bikes, and the ElliptiGO®. The purpose of this study was to assess trunk and lower extremity muscle activity among treadmill walking, cycling (recumbent and upright) and the ElliptiGO® cycling. It was hypothesized that the ElliptiGO® and treadmill would elicit similar electromyographic muscle activity responses compared to the stationary bike and recumbent bike during an exercise session. Cohort, repeated measures. Twelve recreationally active volunteers participated in the study and were assigned a random order of exercise for each of the four devices (ElliptiGO®, stationary upright cycle ergometer, recumbent ergometer, and a treadmill). Two-dimensional video was used to monitor the start and stop of exercise and surface electromyography (SEMG) were used to assess muscle activity during two minutes of cycling or treadmill walking at 40-50% heart rate reserve (HRR). Eight muscles on the dominant limb were used for analysis: gluteus maximus (Gmax), gluteus medius (Gmed), biceps femoris (BF), lateral head of the gastrocnemius (LG), tibialis anterior (TA), rectus femoris (RF). Two trunk muscles were assessed on the same side; lumbar erector spinae at L3-4 level (LES) and rectus abdominus (RA). Maximal voluntary isometric contractions (MVIC) were determined for each muscle and SEMG data were expressed as %MVIC in order to normalize outputs. The %MVIC for RF during ElliptiGO® cycling was higher than recumbent cycling. The LG muscle activity was highest during upright cycling. The TA was higher during walking compared to recumbent cycling and ElliptiGO® cycling. No differences were found among the the LES and remaining lower limb musculature across devices. ElliptiGO® cycling was found to elicit sufficient muscle activity to provide a strengthening stimulus for the RF muscle. The LES, RA, Gmax, Gmed, and BF activity were similar across all devices and ranged from low to moderate strength levels of muscle activation. The information gained from this study may assist clinicians in developing low to moderate strengthening exercise protocols when using these four devices. 3.

Serum caffeine and paraxanthine concentrations and menstrual cycle function: correlations with beverage intakes and associations with race, reproductive hormones, and anovulation in the BioCycle Study.

PubMed

Schliep, Karen C; Schisterman, Enrique F; Wactawski-Wende, Jean; Perkins, Neil J; Radin, Rose G; Zarek, Shvetha M; Mitchell, Emily M; Sjaarda, Lindsey A; Mumford, Sunni L

2016-07-01

Clinicians often recommend limiting caffeine intake while attempting to conceive; however, few studies have evaluated the associations between caffeine exposure and menstrual cycle function, and we are aware of no previous studies assessing biological dose via well-timed serum measurements. We assessed the relation between caffeine and its metabolites and reproductive hormones in a healthy premenopausal cohort and evaluated potential effect modification by race. Participants (n = 259) were followed for ≤2 menstrual cycles and provided fasting blood specimens ≤8 times/cycle. Linear mixed models were used to estimate associations between serum caffeine biomarkers and geometric mean reproductive hormones, whereas Poisson regression was used to assess risk of sporadic anovulation. The highest compared with the lowest serum caffeine tertile was associated with lower total testosterone [27.9 ng/dL (95% CI: 26.7, 29.0 ng/dL) compared with 29.1 ng/dL (95% CI: 27.9, 30.3 ng/dL), respectively] and free testosterone [0.178 ng/mL (95% CI: 0.171, 0.185 ng/dL) compared with 0.186 ng/mL (95% CI: 0.179, 0.194 ng/dL), respectively] after adjustment for age, race, percentage of body fat, daily vigorous exercise, perceived stress, depression, dietary factors, and alcohol intake. The highest tertiles compared with the lowest tertiles of caffeine and paraxanthine were also associated with reduced risk of anovulation [adjusted RRs (aRRs): 0.39 (95% CI: 0.18, 0.87) and 0.40 (95% CI: 0.18, 0.87), respectively]. Additional adjustment for self-reported coffee intake did not alter the reproductive hormone findings and only slightly attenuated the results for serum caffeine and paraxanthine and anovulation. Although reductions in the concentrations of total testosterone and free testosterone and decreased risk of anovulation were greatest in Asian women, there was no indication of effect modification by race. Caffeine intake, irrespective of the beverage source, may be associated with reduced testosterone and improved menstrual cycle function in healthy premenopausal women. © 2016 American Society for Nutrition.

Serum caffeine and paraxanthine concentrations and menstrual cycle function: correlations with beverage intakes and associations with race, reproductive hormones, and anovulation in the BioCycle Study12

PubMed Central

Schisterman, Enrique F; Wactawski-Wende, Jean; Perkins, Neil J; Radin, Rose G; Zarek, Shvetha M; Mitchell, Emily M; Sjaarda, Lindsey A; Mumford, Sunni L

2016-01-01

Background: Clinicians often recommend limiting caffeine intake while attempting to conceive; however, few studies have evaluated the associations between caffeine exposure and menstrual cycle function, and we are aware of no previous studies assessing biological dose via well-timed serum measurements. Objectives: We assessed the relation between caffeine and its metabolites and reproductive hormones in a healthy premenopausal cohort and evaluated potential effect modification by race. Design: Participants (n = 259) were followed for ≤2 menstrual cycles and provided fasting blood specimens ≤8 times/cycle. Linear mixed models were used to estimate associations between serum caffeine biomarkers and geometric mean reproductive hormones, whereas Poisson regression was used to assess risk of sporadic anovulation. Results: The highest compared with the lowest serum caffeine tertile was associated with lower total testosterone [27.9 ng/dL (95% CI: 26.7, 29.0 ng/dL) compared with 29.1 ng/dL (95% CI: 27.9, 30.3 ng/dL), respectively] and free testosterone [0.178 ng/mL (95% CI: 0.171, 0.185 ng/dL) compared with 0.186 ng/mL (95% CI: 0.179, 0.194 ng/dL), respectively] after adjustment for age, race, percentage of body fat, daily vigorous exercise, perceived stress, depression, dietary factors, and alcohol intake. The highest tertiles compared with the lowest tertiles of caffeine and paraxanthine were also associated with reduced risk of anovulation [adjusted RRs (aRRs): 0.39 (95% CI: 0.18, 0.87) and 0.40 (95% CI: 0.18, 0.87), respectively]. Additional adjustment for self-reported coffee intake did not alter the reproductive hormone findings and only slightly attenuated the results for serum caffeine and paraxanthine and anovulation. Although reductions in the concentrations of total testosterone and free testosterone and decreased risk of anovulation were greatest in Asian women, there was no indication of effect modification by race. Conclusion: Caffeine intake, irrespective of the beverage source, may be associated with reduced testosterone and improved menstrual cycle function in healthy premenopausal women. PMID:27225433

Life-Cycle Assessment of Biodiesel Produced from Grease Trap Waste.

PubMed

Hums, Megan E; Cairncross, Richard A; Spatari, Sabrina

2016-03-01

Grease trap waste (GTW) is a low-quality waste material with variable lipid content that is an untapped resource for producing biodiesel. Compared to conventional biodiesel feedstocks, GTW requires different and additional processing steps for biodiesel production due to its heterogeneous composition, high acidity, and high sulfur content. Life-cycle assessment (LCA) is used to quantify greenhouse gas emissions, fossil energy demand, and criteria air pollutant emissions for the GTW-biodiesel process, in which the sensitivity to lipid concentration in GTW is analyzed using Monte Carlo simulation. The life-cycle environmental performance of GTW-biodiesel is compared to that of current GTW disposal, the soybean-biodiesel process, and low-sulfur diesel (LSD). The disposal of the water and solid wastes produced from separating lipids from GTW has a high contribution to the environmental impacts; however, the impacts of these processed wastes are part of the current disposal practice for GTW and could be excluded with consequential LCA system boundaries. At lipid concentrations greater than 10%, most of the environmental metrics studied are lower than those of LSD and comparable to soybean biodiesel.

Life cycle assessments of urban water systems: a comparative analysis of selected peer-reviewed literature.

PubMed

Loubet, Philippe; Roux, Philippe; Loiseau, Eleonore; Bellon-Maurel, Veronique

2014-12-15

Water is a growing concern in cities, and its sustainable management is very complex. Life cycle assessment (LCA) has been increasingly used to assess the environmental impacts of water technologies during the last 20 years. This review aims at compiling all LCA papers related to water technologies, out of which 18 LCA studies deals with whole urban water systems (UWS). A focus is carried out on these 18 case studies which are analyzed according to criteria derived from the four phases of LCA international standards. The results show that whereas the case studies share a common goal, i.e., providing quantitative information to policy makers on the environmental impacts of urban water systems and their forecasting scenarios, they are based on different scopes, resulting in the selection of different functional units and system boundaries. A quantitative comparison of life cycle inventory and life cycle impact assessment data is provided, and the results are discussed. It shows the superiority of information offered by multi-criteria approaches for decision making compared to that derived from mono-criterion. From this review, recommendations on the way to conduct the environmental assessment of urban water systems are given, e.g., the need to provide consistent mass balances in terms of emissions and water flows. Remaining challenges for urban water system LCAs are identified, such as a better consideration of water users and resources and the inclusion of recent LCA developments (territorial approaches and water-related impacts). Copyright © 2014 Elsevier Ltd. All rights reserved.

Life cycle assessment of switchgrass- and corn stover-derived ethanol-fueled automobiles.

PubMed

Spatari, Sabrina; Zhang, Yimin; MacLean, Heather L

2005-12-15

Utilizing domestically produced cellulose-derived ethanol for the light-duty vehicle fleet can potentially improve the environmental performance and sustainability of the transport and energy sectors of the economy. A life cycle assessment model was developed to examine environmental implications of the production and use of ethanol in automobiles in Ontario, Canada. The results were compared to those of low-sulfur reformulated gasoline (RFG) in a functionally equivalent automobile. Two time frames were evaluated, one near-term (2010), which examines converting a dedicated energy crop (switchgrass) and an agricultural residue (corn stover) to ethanol; and one midterm (2020), which assumes technological improvements in the switchgrass-derived ethanol life cycle. Near-term results show that, compared to a RFG automobile, life cycle greenhouse gas (GHG) emissions are 57% lower for an E85-fueled automobile derived from switchgrass and 65% lower for ethanol from corn stover, on a grams of CO2 equivalent per kilometer basis. Corn stover ethanol exhibits slightly lower life cycle GHG emissions, primarily due to sharing emissions with grain production. Through projected improvements in crop and ethanol yields, results for the mid-term scenario show that GHG emissions could be 25-35% lower than those in 2010 and that, even with anticipated improvements in RFG automobiles, E85 automobiles could still achieve up to 70% lower GHG emissions across the life cycle.

Elevated Choline-Containing Compound Levels in Rapid Cycling Bipolar Disorder.

PubMed

Cao, Bo; Stanley, Jeffrey A; Passos, Ives Cavalcante; Mwangi, Benson; Selvaraj, Sudhakar; Zunta-Soares, Giovana B; Soares, Jair C

2017-10-01

Previous studies have found increased levels of choline-containing compounds (ie, glycerophosphocholine plus phosphocholine (GPC+PC)) in bipolar disorder using in vivo proton magnetic resonance spectroscopy ( 1 H MRS), especially in bipolar I disorder (BD-I). Increased levels of GPC+PC suggest alterations in the membrane phospholipids metabolism in bipolar disorder. Rapid cycling (RC) bipolar disorder is considered as a severe course of bipolar disorder, but it is unclear whether rapid cycling bipolar disorder is linked to highly altered membrane phospholipid metabolism. The purpose of this study was to investigate whether the regional extent of elevated GPC+PC were greater in BD-I patients with rapid cycling compared to BD-I patients without rapid cycling and healthy controls. Using a multi-voxel 1 H MRS approach at 3 Tesla with high spatial resolution and absolute quantification, GPC+PC levels from the anterior cingulate cortex (ACC), caudate and putamen of 16 RC BD-I, 34 non-RC BD-I and 44 healthy controls were assessed. We found significantly elevated GPC+PC levels in ACC, putamen and caudate of RC BD-I patients compared to healthy controls (P<0.005) and in ACC compared to non-RC BD-I patients (P<0.05). These results suggest greater alteration of membrane phospholipid metabolisms in rapid cycling BD-I compared to non-rapid-cycling BD-I.

Life cycle assessment of the application of nanoclays in wire coating

NASA Astrophysics Data System (ADS)

Tellaetxe, A.; Blázquez, M.; Arteche, A.; Egizabal, A.; Ermini, V.; Rose, J.; Chaurand, P.; Unzueta, I.

2012-09-01

A life cycle assessment (LCA) is carried out to compare nanoclay-reinforced polymer wire coatings with conventional ones. While the conventional wire coatings contain standard halogen free retardants, in reinforced coatings, montmorillonite (nanoclay) is incorporated into electric cable linings as a rheological agent for an increased resistance to fire. In addition, a reduced load of standard halogen free retardants is obtained. The synergistic effect of the montmorillonite on traditional flame retardant additives (by the formation of a three-dimensional char network) can lead to a revolution in wire production. The application of nanoclays contributes also to anti-dripping effect and flexibility increase [1]. Some producers have already started commercializing wire with nanotechnology-based coating; in the short term the use of nanoclay in wire coating production will probably reach a significant market share replacing traditional formulations. The main aim of this study is to compare the environmental impacts along the life cycle of a traditional wire coating (mineral flame retardants like ATH or MDH in a polymer matrix) with the nanoclay-reinforced wire coating, where the montmorillonite replaces a low percentage of the mineral flame retardant. The system boundaries of the study include the following unit processes: nanoclay production, thermoplastic material and mineral flame retardants production, cable coating manufacturing by extrusion and different end of life scenarios (recycling, incineration and landfill disposal). Whereas nanoreinforced composites have shown and increased fire retardance, the addition of nanomaterials seems to have no significant relevance in the environmental assessment. However, the lack of nano-specific characterization factors for nanomaterials and emission rates associated to the different life cycle stages -mainly in the extrusion and use phase, where accidental combustions can take place- still remains a challenge for realistic life cycle assessment modelling.

Life cycle assessment of lignocellulosic ethanol: a review of key factors and methods affecting calculated GHG emissions and energy use.

PubMed

Gerbrandt, Kelsey; Chu, Pei Lin; Simmonds, Allison; Mullins, Kimberley A; MacLean, Heather L; Griffin, W Michael; Saville, Bradley A

2016-04-01

Lignocellulosic ethanol has potential for lower life cycle greenhouse gas emissions compared to gasoline and conventional grain-based ethanol. Ethanol production 'pathways' need to meet economic and environmental goals. Numerous life cycle assessments of lignocellulosic ethanol have been published over the last 15 years, but gaps remain in understanding life cycle performance due to insufficient data, and model and methodological issues. We highlight key aspects of these issues, drawing on literature and a case study of corn stover ethanol. Challenges include the complexity of feedstock/ecosystems and market-mediated aspects and the short history of commercial lignocellulosic ethanol facilities, which collectively have led to uncertainty in GHG emissions estimates, and to debates on LCA methods and the role of uncertainty in decision making. Copyright © 2016 Elsevier Ltd. All rights reserved.

Life cycle design metrics for energy generation technologies: Method, data, and case study

NASA Astrophysics Data System (ADS)

Cooper, Joyce; Lee, Seung-Jin; Elter, John; Boussu, Jeff; Boman, Sarah

A method to assist in the rapid preparation of Life Cycle Assessments of emerging energy generation technologies is presented and applied to distributed proton exchange membrane fuel cell systems. The method develops life cycle environmental design metrics and allows variations in hardware materials, transportation scenarios, assembly energy use, operating performance and consumables, and fuels and fuel production scenarios to be modeled and comparisons to competing systems to be made. Data and results are based on publicly available U.S. Life Cycle Assessment data sources and are formulated to allow the environmental impact weighting scheme to be specified. A case study evaluates improvements in efficiency and in materials recycling and compares distributed proton exchange membrane fuel cell systems to other distributed generation options. The results reveal the importance of sensitivity analysis and system efficiency in interpreting case studies.

Life-Cycle Costing of Food Waste Management in Denmark: Importance of Indirect Effects.

PubMed

Martinez-Sanchez, Veronica; Tonini, Davide; Møller, Flemming; Astrup, Thomas Fruergaard

2016-04-19

Prevention has been suggested as the preferred food waste management solution compared to alternatives such as conversion to animal fodder or to energy. In this study we used societal life-cycle costing, as a welfare economic assessment, and environmental life-cycle costing, as a financial assessment combined with life-cycle assessment, to evaluate food waste management. Both life-cycle costing assessments included direct and indirect effects. The latter are related to income effects, accounting for the marginal consumption induced when alternative scenarios lead to different household expenses, and the land-use-changes effect, associated with food production. The results highlighted that prevention, while providing the highest welfare gains as more services/goods could be consumed with the same income, could also incur the highest environmental impacts if the monetary savings from unpurchased food commodities were spent on goods/services with a more environmentally damaging production than that of the (prevented) food. This was not the case when savings were used, e.g., for health care, education, and insurances. This study demonstrates that income effects, although uncertain, should be included whenever alternative scenarios incur different financial costs. Furthermore, it highlights that food prevention measures should not only demote the purchase of unconsumed food but also promote a low-impact use of the savings generated.

Recurrent implantation failure in IVF: features of cycles that eventually ended in conception.

PubMed

Bord, Ilia; Tamir, Belle; Harlev, Avraham; Har-Vardi, Iris; Lunenfeld, Eitan; Friger, Michael; Levitas, Eliahu

2016-04-01

To evaluate the characteristics of patients and IVF cycles with recurrent implantation failure who eventually succeeded to conceive compared to those who failed to do so. In a retrospective study, we explored our database for patients younger than 35 years old who underwent at least three unsuccessful fresh IVF cycles. The following parameters were analyzed: cause of infertility, FSH level, stimulation cycle characteristics, fertilization rate, the type of luteal support, and cycle outcome. Uterine cavity assessment was also included. The relationship between endometrial scratching and the outcome of the following IVF cycle was assessed for the subsequent pregnancy rate. The study included 184 patients who underwent 854 IVF cycles. There were no statistically significant differences between patients who eventually conceived and those who did not in terms of ovarian reserve and response to gonadotropin treatment. IVF cycles that eventually ended with conception were characterized by shorter stimulation (10.87 ± 2.17 versus 11.34 ± 2.33 days, p < 0.05), higher estrogen level on the day of hCG administration (1661 ± 667 versus 1472 ± 633 pg/ml, p = 0.009), more fertilized oocytes via ICSI (5.04 ± 4.29 versus 3.85 ± 3.45, p = 0.002), and more embryos available for transfer (5.98 ± 3.89 versus 5.12 ± 3.31, p = 0.002). Combined estrogen and progesterone luteal support combined with endometrial scratching prior to the subsequent IVF cycle has been positively related to increased pregnancy rates. Young patients with RIF having a normal ovarian reserve and satisfactory ovarian response to superovulation should be encouraged to pursue IVF, even though the probability to conceive is relatively low compared to the general IVF population.

Atherosclerosis and cardiac function assessment in low-density lipoprotein receptor-deficient mice undergoing body weight cycling.

PubMed

McMillen, T S; Minami, E; Leboeuf, R C

2013-06-24

Obesity has become an epidemic in many countries and is supporting a billion dollar industry involved in promoting weight loss through diet, exercise and surgical procedures. Because of difficulties in maintaining body weight reduction, a pattern of weight cycling often occurs (so called 'yo-yo' dieting) that may result in deleterious outcomes to health. There is controversy about cardiovascular benefits of yo-yo dieting, and an animal model is needed to better understand the contributions of major diet and body weight changes on heart and vascular functions. Our purpose is to determine the effects of weight cycling on cardiac function and atherosclerosis development in a mouse model. We used low-density lipoprotein receptor-deficient mice due to their sensitivity to metabolic syndrome and cardiovascular diseases when fed high-fat diets. Alternating ad libitum feeding of high-fat and low-fat (rodent chow) diets was used to instigate weight cycling during a 29-week period. Glucose tolerance and insulin sensitivity tests were done at 22 and 24 weeks, echocardiograms at 25 weeks and atherosclerosis and plasma lipoproteins assessed at 29 weeks. Mice subjected to weight cycling showed improvements in glucose homeostasis during the weight loss cycle. Weight-cycled mice showed a reduction in the severity of atherosclerosis as compared with high-fat diet-fed mice. However, atherosclerosis still persisted in weight-cycled mice as compared with mice fed rodent chow. Cardiac function was impaired in weight-cycled mice and matched with that of mice fed only the high-fat diet. This model provides an initial structure in which to begin detailed studies of diet, calorie restriction and surgical modifications on energy balance and metabolic diseases. This model also shows differential effects of yo-yo dieting on metabolic syndrome and cardiovascular diseases.

Life cycle assessment comparison of activated sludge, trickling filter, and high-rate anaerobic-aerobic digestion (HRAAD).

PubMed

Postacchini, Leonardo; Lamichhane, Krishna M; Furukawa, Dennis; Babcock, Roger W; Ciarapica, F E; Cooney, Michael J

2016-01-01

This paper conducts a comparative assessment of the environmental impacts of three methods of treating primary clarifier effluent in wastewater treatment plants (WWTPs) through life cycle assessment methodology. The three technologies, activated sludge (AS), high rate anaerobic-aerobic digestion (HRAAD), and trickling filter (TF), were assessed for treatment of wastewater possessing average values of biochemical oxygen demand and total suspended solids of 90 mg L(-1) and 70 mg L(-1), respectively. The operational requirements to process the municipal wastewater to effluent that meets USEPA regulations have been calculated. The data for the AS system were collected from the East Honolulu WWTP (Hawaii, USA) while data for the HRAAD system were collected from a demonstration-scale system at the same plant. The data for the TF system were estimated from published literature. Two different assessment methods have been used in this study: IMPACT 2002+ and TRACI 2. The results show that TF had the smallest environmental impacts and that AS had the largest, while HRAAD was in between the two but with much reduced impacts compared with AS. Additionally, the study shows that lower sludge production is the greatest advantage of HRAAD for reducing environmental impacts compared with AS.

TEF Bibliography

Science.gov Websites

] Cervero, Robert; Kockelman, Kara. (1997). "Travel demand and the 3Ds: Density, diversity, and design efficient design of sustainable goods and services." The International Journal of Life Cycle Assessment . Upper Saddle River, NJ: FT Press. [202] Das, Sujit. (2004). "A Comparative Assessment of

Performance potential of combined cycles integrated with low-Btu gasifiers for future electric utility applications

NASA Technical Reports Server (NTRS)

Nainiger, J. J.; Burns, R. K.

1977-01-01

A comparison and an assessment of 10 advanced utility power systems on a consistent basis and to a common level of detail were analyzed. Substantial emphasis was given to a combined cycle systems integrated with low-Btu gasifiers. Performance and cost results from that study were presented for these combined cycle systems, together with a comparative evaluation. The effect of the gasifier type and performance and the interface between the gasifier and the power system were discussed.

The usefulness of GPS bicycle tracking data for evaluating the impact of infrastructure change on cycling behaviour.

PubMed

Heesch, Kristiann C; Langdon, Michael

2016-02-01

Issue addressed A key strategy to increase active travel is the construction of bicycle infrastructure. Tools to evaluate this strategy are limited. This study assessed the usefulness of a smartphone GPS tracking system for evaluating the impact of this strategy on cycling behaviour. Methods Cycling usage data were collected from Queenslanders who used a GPS tracking app on their smartphone from 2013-2014. 'Heat' and volume maps of the data were reviewed, and GPS bicycle counts were compared with surveillance data and bicycle counts from automatic traffic-monitoring devices. Results Heat maps broadly indicated that changes in cycling occurred near infrastructure improvements. Volume maps provided changes in counts of cyclists due to these improvements although errors were noted in geographic information system (GIS) geo-coding of some GPS data. Large variations were evident in the number of cyclists using the app in different locations. These variations limited the usefulness of GPS data for assessing differences in cycling across locations. Conclusion Smartphone GPS data are useful in evaluating the impact of improved bicycle infrastructure in one location. Using GPS data to evaluate differential changes in cycling across multiple locations is problematic when there is insufficient traffic-monitoring devices available to triangulate GPS data with bicycle traffic count data. So what? The use of smartphone GPS data with other data sources is recommended for assessing how infrastructure improvements influence cycling behaviour.

Life Cycle Assessment of Bio-diesel Production—A Comparative Analysis

NASA Astrophysics Data System (ADS)

Chatterjee, R.; Sharma, V.; Mukherjee, S.; Kumar, S.

2014-04-01

This work deals with the comparative analysis of environmental impacts of bio-diesel produced from Jatropha curcas, Rapeseed and Palm oil by applying the life cycle assessment and eco-efficiency concepts. The environmental impact indicators considered in the present paper include global warming potential (GWP, CO2 equivalent), acidification potential (AP, SO2 equivalent) and eutrophication potential (EP, NO3 equivalent). Different weighting techniques have been used to present and evaluate the environmental characteristics of bio-diesel. With the assistance of normalization values, the eco-efficiency was demonstrated in this work. The results indicate that the energy consumption of bio-diesel production is lowest in Jatropha while AP and EP are more in case of Jatropha than that of Rapeseed and Palm oil.

Anaerobic co-digestion of municipal food waste and sewage sludge: A comparative life cycle assessment in the context of a waste service provision.

PubMed

Edwards, Joel; Othman, Maazuza; Crossin, Enda; Burn, Stewart

2017-01-01

This study used life cycle assessment to evaluate the environmental impact of anaerobic co-digestion (AcoD) and compared it against the current waste management system in two case study areas. Results indicated AcoD to have less environmental impact for all categories modelled excluding human toxicity, despite the need to collect and pre-treat food waste separately. Uncertainty modelling confirmed that AcoD has a 100% likelihood of a smaller global warming potential, and for acidification, eutrophication and fossil fuel depletion AcoD carried a greater than 85% confidence of inducing a lesser impact than the current waste service. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.

Life cycle assessment of greenhouse gas emissions from plug-in hybrid vehicles: implications for policy.

PubMed

Samaras, Constantine; Meisterling, Kyle

2008-05-01

Plug-in hybrid electric vehicles (PHEVs), which use electricity from the grid to power a portion of travel, could play a role in reducing greenhouse gas (GHG) emissions from the transport sector. However, meaningful GHG emissions reductions with PHEVs are conditional on low-carbon electricity sources. We assess life cycle GHG emissions from PHEVs and find that they reduce GHG emissions by 32% compared to conventional vehicles, but have small reductions compared to traditional hybrids. Batteries are an important component of PHEVs, and GHGs associated with lithium-ion battery materials and production account for 2-5% of life cycle emissions from PHEVs. We consider cellulosic ethanol use and various carbon intensities of electricity. The reduced liquid fuel requirements of PHEVs could leverage limited cellulosic ethanol resources. Electricity generation infrastructure is long-lived, and technology decisions within the next decade about electricity supplies in the power sector will affectthe potential for large GHG emissions reductions with PHEVs for several decades.

Differences in physical environmental characteristics between adolescents' actual and shortest cycling routes: a study using a Google Street View-based audit.

PubMed

Verhoeven, Hannah; Van Hecke, Linde; Van Dyck, Delfien; Baert, Tim; Van de Weghe, Nico; Clarys, Peter; Deforche, Benedicte; Van Cauwenberg, Jelle

2018-05-29

The objective evaluation of the physical environmental characteristics (e.g. speed limit, cycling infrastructure) along adolescents' actual cycling routes remains understudied, although it may provide important insights into why adolescents prefer one cycling route over another. The present study aims to gain insight into the physical environmental characteristics determining the route choice of adolescent cyclists by comparing differences in physical environmental characteristics between their actual cycling routes and the shortest possible cycling routes. Adolescents (n = 204; 46.5% boys; 14.4 ± 1.2 years) recruited at secondary schools in and around Ghent (city in Flanders, northern part of Belgium) were instructed to wear a Global Positioning System device in order to identify cycling trips. For all identified cycling trips, the shortest possible route that could have been taken was calculated. Actual cycling routes that were not the shortest possible cycling routes were divided into street segments. Segments were audited with a Google Street View-based tool to assess physical environmental characteristics along actual and shortest cycling routes. Out of 160 actual cycling trips, 73.1% did not differ from the shortest possible cycling route. For actual cycling routes that were not the shortest cycling route, a speed limit of 30 km/h, roads having few buildings with windows on the street side and roads without cycle lane were more frequently present compared to the shortest possible cycling routes. A mixed land use, roads with commercial destinations, arterial roads, cycle lanes separated from traffic by white lines, small cycle lanes and cycle lanes covered by lighting were less frequently present along actual cycling routes compared to the shortest possible cycling routes. Results showed that distance mainly determines the route along which adolescents cycle. In addition, adolescents cycled more along residential streets (even if no cycle lane was present) and less along busy, arterial roads. Local authorities should provide shortcuts free from motorised traffic to meet adolescents' preference to cycle along the shortest route and to avoid cycling along arterial roads.

Comparing the environmental footprints of home-care and personal-hygiene products: the relevance of different life-cycle phases.

PubMed

Koehler, Annette; Wildbolz, Caroline

2009-11-15

An in-depth life-cycle assessment of nine home-care and personal-hygiene products was conducted to determine the ecological relevance of different life-cycle phases and compare the environmental profiles of products serving equal applications. Using detailed data from industry and consumer-behavior studies a broad range of environmental impacts were analyzed to identify the main drivers in each life-cycle stage and potentials for improving the environmental footprints. Although chemical production significantly adds to environmental burdens, substantial impacts are caused in the consumer-use phase. As such, this research provides recommendations for product development, supply chain management, product policies, and consumer use. To reduce environmental burdens products should, for instance, be produced in concentrated form, while consumers should apply correct product dosages and low water temperatures during product application.

Health and safety: Preliminary comparative assessment of the Satellite Power System (SPS) and other energy alternatives

NASA Technical Reports Server (NTRS)

Habegger, L. J.; Gasper, J. R.; Brown, C.

1980-01-01

Data readily available from the literature were used to make an initial comparison of the health and safety risks of a fission power system with fuel reprocessing; a combined-cycle coal power system with a low-Btu gasifier and open-cycle gas turbine; a central-station, terrestrial, solar photovoltaic power system; the satellite power system; and a first-generation fusion system. The assessment approach consists of the identification of health and safety issues in each phase of the energy cycle from raw material extraction through electrical generation, waste disposal, and system deactivation; quantitative or qualitative evaluation of impact severity; and the rating of each issue with regard to known or potential impact level and level of uncertainty.

Life Cycle Impact Assessment for Land Use

EPA Science Inventory

According to the Millennium Assessment: “Over the past 50 years, humans have changed ecosystems more rapidly and extensively than in any comparable period of time in human history, largely to meet rapidly growing demands for food, fresh water, timber, fiber, and fuel. This has ...

Life cycle assessment to compare the environmental impact of seven contemporary food waste management systems.

PubMed

Edwards, Joel; Othman, Maazuza; Crossin, Enda; Burn, Stewart

2018-01-01

Municipal food waste (FW) represents 35-45% of household residual waste in Australia, with the nation generating 1.6Tg annually. It is estimated that 91% of this FW ends up in landfill. This study used life cycle assessment to determine and compare the environmental impact of seven contemporary FW management systems for two real-life jurisdictions; incorporating the complete waste service and expanding the system to include inert and garden waste. Although, no system exhibited a best ranking across all impact categories, FW digestion based systems were all revealed to have a lower global warming potential than composting and landfilling systems. Mechanical biological treatment, anaerobic co-digestion, and home composting all demonstrated the lowest environmental impacts for two or more of the environmental impact categories assessed. The assessment included market and technological specific variables and uncertainties providing a framework for robust decision making at a municipality level. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Increasing synthetic serum substitute (SSS) concentrations in P1 glucose/phosphate-free medium improves implantation rate: a comparative study.

PubMed

Ben-Yosef, D; Yovel, I; Schwartz, T; Azem, F; Lessing, J B; Amit, A

2001-11-01

To assess the comparative efficacy of IVF medium (MediCult, with 5.2 mM glucose) and a glucose/phosphate-free medium, P1 (Irvine Scientific), and to investigate the influence of increasing the serum supplementation (synthetic serum substitute; SSS; Irvine Scientific) to P1 on embryo development and implantation. Patients were randomly assigned to IVF medium (Group 1, cycles n = 172) or P1 supplemented with 10% SSS (Group 2, cycles n = 229) according to the medium scheduled for use on the day of oocyte retrieval. Another 555 IVF consequent cycles (Group 3) were performed using increased SSS concentrations (20%) in P1 medium. In this large series of IVF cycles, we herein demonstrate that significantly higher pregnancy and implantation rates were found when embryos were cultured in glucose/phosphate-free medium P1 supplemented with 20% SSS compared to supplementation with the lower SSS concentration and with IVF medium.

Fresh embryo transfer versus frozen embryo transfer in in vitro fertilization cycles: a systematic review and meta-analysis.

PubMed

Roque, Matheus; Lattes, Karinna; Serra, Sandra; Solà, Ivan; Geber, Selmo; Carreras, Ramón; Checa, Miguel Angel

2013-01-01

To examine the available evidence to assess if cryopreservation of all embryos and subsequent frozen embryo transfer (FET) results in better outcomes compared with fresh transfer. Systematic review and meta-analysis. Centers for reproductive care. Infertility patient(s). An exhaustive electronic literature search in MEDLINE, EMBASE, and the Cochrane Library was performed through December 2011. We included randomized clinical trials comparing outcomes of IVF cycles between fresh and frozen embryo transfers. The outcomes of interest were ongoing pregnancy rate, clinical pregnancy rate, and miscarriage. We included three trials accounting for 633 cycles in women aged 27-33 years. Data analysis showed that FET resulted in significantly higher ongoing pregnancy rates and clinical pregnancy rates. Our results suggest that there is evidence that IVF outcomes may be improved by performing FET compared with fresh embryo transfer. This could be explained by a better embryo-endometrium synchrony achieved with endometrium preparation cycles. Copyright © 2013 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Impact Assessment and Environmental Evaluation of Various Ammonia Production Processes

NASA Astrophysics Data System (ADS)

Bicer, Yusuf; Dincer, Ibrahim; Vezina, Greg; Raso, Frank

2017-05-01

In the current study, conventional resources-based ammonia generation routes are comparatively studied through a comprehensive life cycle assessment. The selected ammonia generation options range from mostly used steam methane reforming to partial oxidation of heavy oil. The chosen ammonia synthesis process is the most common commercially available Haber-Bosch process. The essential energy input for the methods are used from various conventional resources such as coal, nuclear, natural gas and heavy oil. Using the life cycle assessment methodology, the environmental impacts of selected methods are identified and quantified from cradle to gate. The life cycle assessment outcomes of the conventional resources based ammonia production routes show that nuclear electrolysis-based ammonia generation method yields the lowest global warming and climate change impacts while the coal-based electrolysis options bring higher environmental problems. The calculated greenhouse gas emission from nuclear-based electrolysis is 0.48 kg CO2 equivalent while it is 13.6 kg CO2 per kg of ammonia for coal-based electrolysis method.

Impact Assessment and Environmental Evaluation of Various Ammonia Production Processes.

PubMed

Bicer, Yusuf; Dincer, Ibrahim; Vezina, Greg; Raso, Frank

2017-05-01

In the current study, conventional resources-based ammonia generation routes are comparatively studied through a comprehensive life cycle assessment. The selected ammonia generation options range from mostly used steam methane reforming to partial oxidation of heavy oil. The chosen ammonia synthesis process is the most common commercially available Haber-Bosch process. The essential energy input for the methods are used from various conventional resources such as coal, nuclear, natural gas and heavy oil. Using the life cycle assessment methodology, the environmental impacts of selected methods are identified and quantified from cradle to gate. The life cycle assessment outcomes of the conventional resources based ammonia production routes show that nuclear electrolysis-based ammonia generation method yields the lowest global warming and climate change impacts while the coal-based electrolysis options bring higher environmental problems. The calculated greenhouse gas emission from nuclear-based electrolysis is 0.48 kg CO 2 equivalent while it is 13.6 kg CO 2 per kg of ammonia for coal-based electrolysis method.

Evaluating nanotechnology opportunities and risks through integration of life-cycle and risk assessment.

PubMed

Tsang, Michael P; Kikuchi-Uehara, Emi; Sonnemann, Guido W; Aymonier, Cyril; Hirao, Masahiko

2017-08-04

It has been some 15 years since the topics of sustainability and nanotechnologies first appeared together in the scientific literature and became a focus of organizations' research and policy developments. On the one hand, this focus is directed towards approaches and tools for risk assessment and management and on the other hand towards life-cycle thinking and assessment. Comparable to their application for regular chemicals, each tool is seen to serve separate objectives as it relates to evaluating nanotechnologies' safety or resource efficiency, respectively. While nanomaterials may provide resource efficient production and consumption, this must balance any potential hazards they pose across their life-cycles. This Perspective advocates for integrating these two tools at the methodological level for achieving this objective, and it explains what advantages and challenges this offers decision-makers while highlighting what research is needed to further enhance integration.

Environmental characteristics comparison of Li-ion batteries and Ni-MH batteries under the uncertainty of cycle performance.

PubMed

Yu, Yajuan; Wang, Xiang; Wang, Dong; Huang, Kai; Wang, Lijing; Bao, Liying; Wu, Feng

2012-08-30

An environmental impact assessment model for secondary batteries under uncertainty is proposed, which is a combination of the life cycle assessment (LCA), Eco-indicator 99 system and Monte Carlo simulation (MCS). The LCA can describe the environmental impact mechanism of secondary batteries, whereas the cycle performance was simulated through MCS. The composite LCA-MCS model was then carried out to estimate the environmental impact of two kinds of experimental batteries. Under this kind of standard assessment system, a comparison between different batteries could be accomplished. The following results were found: (1) among the two selected batteries, the environmental impact of the Li-ion battery is lower than the nickel-metal hydride (Ni-MH) battery, especially with regards to resource consumption and (2) the lithium ion (Li-ion) battery is less sensitive to cycle uncertainty, its environmental impact fluctuations are small when compared with the selected Ni-MH battery and it is more environmentally friendly. The assessment methodology and model proposed in this paper can also be used for any other secondary batteries and they can be helpful in the development of environmentally friendly secondary batteries. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

Defining Product Intake Fraction to Quantify and Compare Exposure to Consumer Products.

PubMed

Jolliet, Olivier; Ernstoff, Alexi S; Csiszar, Susan A; Fantke, Peter

2015-08-04

There is a growing consciousness that exposure studies need to better cover near-field exposure associated with products use. To consistently and quantitatively compare human exposure to chemicals in consumer products, we introduce the concept of product intake fraction, as the fraction of a chemical within a product that is eventually taken in by the human population. This metric enables consistent comparison of exposures during consumer product use for different product-chemical combinations, exposure duration, exposure routes and pathways and for other life cycle stages. We present example applications of the product intake fraction concept, for two chemicals in two personal care products and two chemicals encapsulated in two articles, showing how intakes of these chemicals can primarily occur during product use. We demonstrate the utility of the product intake fraction and its application modalities within life cycle assessment and risk assessment contexts. The product intake fraction helps to provide a clear interface between the life cycle inventory and impact assessment phases, to identify best suited sentinel products and to calculate overall exposure to chemicals in consumer products, or back-calculate maximum allowable concentrations of substances inside products.

Combinatorial life cycle assessment to inform process design of industrial production of algal biodiesel.

PubMed

Brentner, Laura B; Eckelman, Matthew J; Zimmerman, Julie B

2011-08-15

The use of algae as a feedstock for biodiesel production is a rapidly growing industry, in the United States and globally. A life cycle assessment (LCA) is presented that compares various methods, either proposed or under development, for algal biodiesel to inform the most promising pathways for sustainable full-scale production. For this analysis, the system is divided into five distinct process steps: (1) microalgae cultivation, (2) harvesting and/or dewatering, (3) lipid extraction, (4) conversion (transesterification) into biodiesel, and (5) byproduct management. A number of technology options are considered for each process step and various technology combinations are assessed for their life cycle environmental impacts. The optimal option for each process step is selected yielding a best case scenario, comprised of a flat panel enclosed photobioreactor and direct transesterification of algal cells with supercritical methanol. For a functional unit of 10 GJ biodiesel, the best case production system yields a cumulative energy demand savings of more than 65 GJ, reduces water consumption by 585 m(3) and decreases greenhouse gas emissions by 86% compared to a base case scenario typical of early industrial practices, highlighting the importance of technological innovation in algae processing and providing guidance on promising production pathways.

Environmental impacts of remediation of a trichloroethene-contaminated site: life cycle assessment of remediation alternatives.

PubMed

Lemming, Gitte; Hauschild, Michael Z; Chambon, Julie; Binning, Philip J; Bulle, Cécile; Margni, Manuele; Bjerg, Poul L

2010-12-01

The environmental impacts of remediation of a chloroethene-contaminated site were evaluated using life cycle assessment (LCA). The compared remediation options are (i) in situ bioremediation by enhanced reductive dechlorination (ERD), (ii) in situ thermal desorption (ISTD), and (iii) excavation of the contaminated soil followed by off-site treatment and disposal. The results showed that choosing the ERD option will reduce the life-cycle impacts of remediation remarkably compared to choosing either ISTD or excavation, which are more energy-demanding. In addition to the secondary impacts of remediation, this study includes assessment of local toxic impacts (the primary impact) related to the on-site contaminant leaching to groundwater and subsequent human exposure via drinking water. The primary human toxic impacts were high for ERD due to the formation and leaching of chlorinated degradation products, especially vinyl chloride during remediation. However, the secondary human toxic impacts of ISTD and excavation are likely to be even higher, particularly due to upstream impacts from steel production. The newly launched model, USEtox, was applied for characterization of primary and secondary toxic impacts and combined with a site-dependent fate model of the leaching of chlorinated ethenes from the fractured clay till site.

Life cycle assessment of cellulose nanofibrils production by mechanical treatment and two different pretreatment processes.

PubMed

Arvidsson, Rickard; Nguyen, Duong; Svanström, Magdalena

2015-06-02

Nanocellulose is a bionanomaterial with many promising applications, but high energy use in production has been described as a potential obstacle for future use. In fact, life cycle assessment studies have indicated high life cycle energy use for nanocellulose. In this study, we assess the cradle-to-gate environmental impacts of three production routes for a particular type of nanocellulose called cellulose nanofibrils (CNF) made from wood pulp. The three production routes are (1) the enzymatic production route, which includes an enzymatic pretreatment, (2) the carboxymethylation route, which includes a carboxymethylation pretreatment, and (3) one route without pretreatment, here called the no pretreatment route. The results show that CNF produced via the carboxymethylation route clearly has the highest environmental impacts due to large use of solvents made from crude oil. The enzymatic and no pretreatment routes both have lower environmental impacts, of similar magnitude. A sensitivity analysis showed that the no pretreatment route was sensitive to the electricity mix, and the carboxymethylation route to solvent recovery. When comparing the results to those of other carbon nanomaterials, it was shown that in particular CNF produced via the enzymatic and no pretreatment routes had comparatively low environmental impacts.

Comparative Human Health Impact Assessment of Engineered Nanomaterials in the Framework of Life Cycle Assessment.

PubMed

Fransman, Wouter; Buist, Harrie; Kuijpers, Eelco; Walser, Tobias; Meyer, David; Zondervan-van den Beuken, Esther; Westerhout, Joost; Klein Entink, Rinke H; Brouwer, Derk H

2017-07-01

For safe innovation, knowledge on potential human health impacts is essential. Ideally, these impacts are considered within a larger life-cycle-based context to support sustainable development of new applications and products. A methodological framework that accounts for human health impacts caused by inhalation of engineered nanomaterials (ENMs) in an indoor air environment has been previously developed. The objectives of this study are as follows: (i) evaluate the feasibility of applying the CF framework for NP exposure in the workplace based on currently available data; and (ii) supplement any resulting knowledge gaps with methods and data from the life cycle approach and human risk assessment (LICARA) project to develop a modified case-specific version of the framework that will enable near-term inclusion of NP human health impacts in life cycle assessment (LCA) using a case study involving nanoscale titanium dioxide (nanoTiO 2 ). The intent is to enhance typical LCA with elements of regulatory risk assessment, including its more detailed measure of uncertainty. The proof-of-principle demonstration of the framework highlighted the lack of available data for both the workplace emissions and human health effects of ENMs that is needed to calculate generalizable characterization factors using common human health impact assessment practices in LCA. The alternative approach of using intake fractions derived from workplace air concentration measurements and effect factors based on best-available toxicity data supported the current case-by-case approach for assessing the human health life cycle impacts of ENMs. Ultimately, the proposed framework and calculations demonstrate the potential utility of integrating elements of risk assessment with LCA for ENMs once the data are available. © 2016 Society for Risk Analysis.

Altered levels of sex and stress steroid hormones assessed daily over a 28-day cycle in early abstinent cocaine-dependent females

PubMed Central

Hong, Kwangik A.; Paliwal, Prashni; Morgan, Peter T.; Sinha, Rajita

2009-01-01

Rationale There is growing evidence of alterations in brain stress and reward circuits associated with cocaine dependence. Sex differences are also documented and sex steroid hormones have been linked to cocaine reinforcement. Objectives The current study therefore assessed daily fluctuations in stress and sex hormones in cocaine-dependent females compared with healthy females. Method Daily salivary samples of cortisol, progesterone, and estradiol were collected at waking across 28 days from 12 cocaine-dependent females receiving inpatient treatment and 10 healthy females. Participants also completed mood-rating scales each week corresponding to four phases of the menstrual cycle and cocaine craving was monitored in cocaine patients at each phase. Results Cocaine-dependent females in their first month of abstinence demonstrated significantly higher levels of both cortisol and progesterone across the menstrual cycle and significantly lower estradiol/progesterone (E2/P) ratios compared to healthy controls. They also showed significantly increased negative mood compared with controls, but no variation in cocaine craving across the menstrual cycle. Conclusions Findings indicate altered stress and sex hormones suggestive of an overactive stress system during the first month of cocaine abstinence after chronic cocaine abuse. These increased levels of cortisol and progesterone could impact both abstinence-related symptoms such as negative mood and susceptibility to drug-seeking behavior in cocaine-dependent females. PMID:17891383

Life Cycle Assessment and Costing Methods for Device Procurement: Comparing Reusable and Single-Use Disposable Laryngoscopes.

PubMed

Sherman, Jodi D; Raibley, Lewis A; Eckelman, Matthew J

2018-01-09

Traditional medical device procurement criteria include efficacy and safety, ease of use and handling, and procurement costs. However, little information is available about life cycle environmental impacts of the production, use, and disposal of medical devices, or about costs incurred after purchase. Reusable and disposable laryngoscopes are of current interest to anesthesiologists. Facing mounting pressure to quickly meet or exceed conflicting infection prevention guidelines and oversight body recommendations, many institutions may be electively switching to single-use disposable (SUD) rigid laryngoscopes or overcleaning reusables, potentially increasing both costs and waste generation. This study provides quantitative comparisons of environmental impacts and total cost of ownership among laryngoscope options, which can aid procurement decision making to benefit facilities and public health. We describe cradle-to-grave life cycle assessment (LCA) and life cycle costing (LCC) methods and apply these to reusable and SUD metal and plastic laryngoscope handles and tongue blade alternatives at Yale-New Haven Hospital (YNHH). The US Environmental Protection Agency's Tool for the Reduction and Assessment of Chemical and other environmental Impacts (TRACI) life cycle impact assessment method was used to model environmental impacts of greenhouse gases and other pollutant emissions. The SUD plastic handle generates an estimated 16-18 times more life cycle carbon dioxide equivalents (CO2-eq) than traditional low-level disinfection of the reusable steel handle. The SUD plastic tongue blade generates an estimated 5-6 times more CO2-eq than the reusable steel blade treated with high-level disinfection. SUD metal components generated much higher emissions than all alternatives. Both the SUD handle and SUD blade increased life cycle costs compared to the various reusable cleaning scenarios at YNHH. When extrapolated over 1 year (60,000 intubations), estimated costs increased between $495,000 and $604,000 for SUD handles and between $180,000 and $265,000 for SUD blades, compared to reusables, depending on cleaning scenario and assuming 4000 (rated) uses. Considering device attrition, reusable handles would be more economical than SUDs if they last through 4-5 uses, and reusable blades 5-7 uses, before loss. LCA and LCC are feasible methods to ease interpretation of environmental impacts and facility costs when weighing device procurement options. While management practices vary between institutions, all standard methods of cleaning were evaluated and sensitivity analyses performed so that results are widely applicable. For YNHH, the reusable options presented a considerable cost advantage, in addition to offering a better option environmentally. Avoiding overcleaning reusable laryngoscope handles and blades is desirable from an environmental perspective. Costs may vary between facilities, and LCC methodology demonstrates the importance of time-motion labor analysis when comparing reusable and disposable device options.

OECD/NEA Ongoing activities related to the nuclear fuel cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cornet, S.M.; McCarthy, K.; Chauvin, N.

2013-07-01

As part of its role in encouraging international collaboration, the OECD Nuclear Energy Agency is coordinating a series of projects related to the Nuclear Fuel Cycle. The Nuclear Science Committee (NSC) Working Party on Scientific Issues of the Nuclear Fuel Cycle (WPFC) comprises five different expert groups covering all aspects of the fuel cycle from front to back-end. Activities related to fuels, materials, physics, separation chemistry, and fuel cycles scenarios are being undertaken. By publishing state-of-the-art reports and organizing workshops, the groups are able to disseminate recent research advancements to the international community. Current activities mainly focus on advanced nuclearmore » systems, and experts are working on analyzing results and establishing challenges associated to the adoption of new materials and fuels. By comparing different codes, the Expert Group on Advanced Fuel Cycle Scenarios is aiming at gaining further understanding of the scientific issues and specific national needs associated with the implementation of advanced fuel cycles. At the back end of the fuel cycle, separation technologies (aqueous and pyrochemical processing) are being assessed. Current and future activities comprise studies on minor actinides separation and post Fukushima studies. Regular workshops are also organized to discuss recent developments on Partitioning and Transmutation. In addition, the Nuclear Development Committee (NDC) focuses on the analysis of the economics of nuclear power across the fuel cycle in the context of changes of electricity markets, social acceptance and technological advances and assesses the availability of the nuclear fuel and infrastructure required for the deployment of existing and future nuclear power. The Expert Group on the Economics of the Back End of the Nuclear Fuel Cycle (EBENFC), in particular, is looking at assessing economic and financial issues related to the long term management of spent nuclear fuel. (authors)« less

Determination of the duty cycle of WLAN for realistic radio frequency electromagnetic field exposure assessment.

PubMed

Joseph, Wout; Pareit, Daan; Vermeeren, Günter; Naudts, Dries; Verloock, Leen; Martens, Luc; Moerman, Ingrid

2013-01-01

Wireless Local Area Networks (WLANs) are commonly deployed in various environments. The WLAN data packets are not transmitted continuously but often worst-case exposure of WLAN is assessed, assuming 100% activity and leading to huge overestimations. Actual duty cycles of WLAN are thus of importance for time-averaging of exposure when checking compliance with international guidelines on limiting adverse health effects. In this paper, duty cycles of WLAN using Wi-Fi technology are determined for exposure assessment on large scale at 179 locations for different environments and activities (file transfer, video streaming, audio, surfing on the internet, etc.). The median duty cycle equals 1.4% and the 95th percentile is 10.4% (standard deviation SD = 6.4%). Largest duty cycles are observed in urban and industrial environments. For actual applications, the theoretical upper limit for the WLAN duty cycle is 69.8% and 94.7% for maximum and minimum physical data rate, respectively. For lower data rates, higher duty cycles will occur. Although counterintuitive at first sight, poor WLAN connections result in higher possible exposures. File transfer at maximum data rate results in median duty cycles of 47.6% (SD = 16%), while it results in median values of 91.5% (SD = 18%) at minimum data rate. Surfing and audio streaming are less intensively using the wireless medium and therefore have median duty cycles lower than 3.2% (SD = 0.5-7.5%). For a specific example, overestimations up to a factor 8 for electric fields occur, when considering 100% activity compared to realistic duty cycles. Copyright © 2012 Elsevier Ltd. All rights reserved.

Cycles of Inquiry: Formative Assessment in Service of Learning in Classrooms and in School-Based Professional Communities

ERIC Educational Resources Information Center

Birenbaum, Menucha; Kimron, Helena; Shilton, Hany; Shahaf-Barzilay, Rinat

2009-01-01

The paper reports results of three studies that used a formative assessment (FA) framework to compare schools that vary in their level of functioning as professional learning communities with respect to three processes: classroom assessment (study 1), development and implementation of school-based curriculum (study 2), and pedagogical…

24 CFR Appendix to Part 972 - Methodology of Comparing Cost of Public Housing With the Cost of Tenant-Based Assistance

Code of Federal Regulations, 2014 CFR

2014-04-01

... justified by a newly created property-based needs assessment (a life-cycle physical needs assessments... calculated as the sum of total operating cost, modernization cost, and costs to address accrual needs. Costs... assist PHAs in completing the assessments. The spreadsheet calculator is designed to walk housing...

24 CFR Appendix to Part 972 - Methodology of Comparing Cost of Public Housing With the Cost of Tenant-Based Assistance

Code of Federal Regulations, 2013 CFR

2013-04-01

... justified by a newly created property-based needs assessment (a life-cycle physical needs assessments... calculated as the sum of total operating cost, modernization cost, and costs to address accrual needs. Costs... assist PHAs in completing the assessments. The spreadsheet calculator is designed to walk housing...

Environmental considerations in the selection of isolation gowns: A life cycle assessment of reusable and disposable alternatives.

PubMed

Vozzola, Eric; Overcash, Michael; Griffing, Evan

2018-04-11

Isolation gowns serve a critical role in infection control by protecting healthcare workers, visitors, and patients from the transfer of microorganisms and body fluids. The decision of whether to use a reusable or disposable garment system is a selection process based on factors including sustainability, barrier effectiveness, cost, and comfort. Environmental sustainability is increasingly being used in the decision-making process. Life cycle assessment is the most comprehensive and widely used tool used to evaluate environmental performance. The environmental impacts of market-representative reusable and disposable isolation gown systems were compared using standard life cycle assessment procedures. The basis of comparison was 1,000 isolation gown uses in a healthcare setting. The scope included the manufacture, use, and end-of-life stages of the gown systems. At the healthcare facility, compared to the disposable gown system, the reusable gown system showed a 28% reduction in energy consumption, a 30% reduction in greenhouse gas emissions, a 41% reduction in blue water consumption, and a 93% reduction in solid waste generation. Selecting reusable garment systems may result in significant environmental benefits compared to selecting disposable garment systems. By selecting reusable isolation gowns, healthcare facilities can add these quantitative benefits directly to their sustainability scorecards. Copyright © 2018 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Fasting cycles potentiate the efficacy of gemcitabine treatment in in vitro and in vivo pancreatic cancer models

PubMed Central

Mazza, Tommaso; Panebianco, Concetta; Saracino, Chiara; Pereira, Stephen P.; Graziano, Paolo; Pazienza, Valerio

2015-01-01

Background/aims Pancreatic cancer (PC) is ranked as the fourth leading cause of cancer-related deaths worldwide. Despite recent advances in treatment options, a modest impact on the outcome of the disease is observed so far. Short-term fasting cycles have been shown to potentiate the efficacy of chemotherapy against glioma. The aim of this study was to assess the effect of fasting cycles on the efficacy of gemcitabine, a standard treatment for PC patients, in vitro and in an in vivo pancreatic cancer mouse xenograft model. Materials and Methods BxPC-3, MiaPaca-2 and Panc-1 cells were cultured in standard and fasting mimicking culturing condition to evaluate the effects of gemcitabine. Pancreatic cancer xenograft mice were subjected to 24h starvation prior to gemcitabine injection to assess the tumor volume and weight as compared to mice fed ad libitum. Results Fasted pancreatic cancer cells showed increased levels of equilibrative nucleoside transporter (hENT1), the transporter of gemcitabine across the cell membrane, and decreased ribonucleotide reductase M1 (RRM1) levels as compared to those cultured in standard medium. Gemcitabine was more effective in inducing cell death on fasted cells as compared to controls. Consistently, xenograft pancreatic cancer mice subjected to fasting cycles prior to gemcitabine injection displayed a decrease of more than 40% in tumor growth. Conclusion Fasting cycles enhance gemcitabine effect in vitro and in the in vivo PC xenograft mouse model. These results suggest that restrictive dietary interventions could enhance the efficacy of existing cancer treatments in pancreatic cancer patients. PMID:26176887

Change in women's eating habits during the menstrual cycle.

PubMed

Kammoun, Ines; Ben Saâda, Wafa; Sifaou, Amira; Haouat, Emna; Kandara, Hajer; Ben Salem, Leila; Ben Slama, Claude

2017-02-01

During the menstrual cycle, the influence of hormonal variations on dietary habits in women has been suggested by several studies. In this context, our work aimed to assess the spontaneous food intake and the anthropometric parameters of women at different periods of their menstrual cycles. This prospective study included 30 healthy women with regular periods (28 to 30 days), aged between 18 and 45. We assessed the spontaneous food intake and the anthropometric measurements (weight and waist circumference) of the participants, during the follicular, peri-ovulatory and luteal phases of their menstrual cycles. Our results showed a slight but significant increase in body weight during the luteal phase (P=0.022) and the follicular phase (P=0.017) compared with the peri-ovulatory phase, without any significant change in waist circumference. The caloric intake increased during the peri-ovulatory (P<0.001) and the luteal phases (P<0.001), compared with the follicular phase, with a significant increase in carbohydrate (P<0.001), lipid (P=0.008) and protein (P=0.008) intake. Our study showed a significant decrease in women's weight during the peri-ovulatory phase, with a significant increase in caloric intake during the luteal phase of the menstrual cycle. Divergent results have been reported by other authors and the physiopathology of these changes is still poorly understood. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Comparison of the Environment, Health, And Safety Characteristics of Advanced Thorium- Uranium and Uranium-Plutonium Fuel Cycles

NASA Astrophysics Data System (ADS)

Ault, Timothy M.

The environment, health, and safety properties of thorium-uranium-based (''thorium'') fuel cycles are estimated and compared to those of analogous uranium-plutonium-based (''uranium'') fuel cycle options. A structured assessment methodology for assessing and comparing fuel cycle is refined and applied to several reference fuel cycle options. Resource recovery as a measure of environmental sustainability for thorium is explored in depth in terms of resource availability, chemical processing requirements, and radiological impacts. A review of available experience and recent practices indicates that near-term thorium recovery will occur as a by-product of mining for other commodities, particularly titanium. The characterization of actively-mined global titanium, uranium, rare earth element, and iron deposits reveals that by-product thorium recovery would be sufficient to satisfy even the most intensive nuclear demand for thorium at least six times over. Chemical flowsheet analysis indicates that the consumption of strong acids and bases associated with thorium resource recovery is 3-4 times larger than for uranium recovery, with the comparison of other chemical types being less distinct. Radiologically, thorium recovery imparts about one order of magnitude larger of a collective occupational dose than uranium recovery. Moving to the entire fuel cycle, four fuel cycle options are compared: a limited-recycle (''modified-open'') uranium fuel cycle, a modified-open thorium fuel cycle, a full-recycle (''closed'') uranium fuel cycle, and a closed thorium fuel cycle. A combination of existing data and calculations using SCALE are used to develop material balances for the four fuel cycle options. The fuel cycle options are compared on the bases of resource sustainability, waste management (both low- and high-level waste, including used nuclear fuel), and occupational radiological impacts. At steady-state, occupational doses somewhat favor the closed thorium option while low-level waste volumes slightly favor the closed uranium option, although uncertainties are significant in both cases. The high-level waste properties (radioactivity, decay heat, and ingestion radiotoxicity) all significantly favor the closed fuel cycle options (especially the closed thorium option), but an alternative measure of key fission product inventories that drive risk in a repository slightly favors the uranium fuel cycles due to lower production of iodine-129. Resource requirements are much lower for the closed fuel cycle options and are relatively similar between thorium and uranium. In additional to the steady-state results, a variety of potential transition pathways are considered for both uranium and thorium fuel cycle end-states. For dose, low-level waste, and fission products contributing to repository risk, the differences among transition impacts largely reflected the steady-state differences. However, the HLW properties arrived at a distinctly opposite result in transition (strongly favoring uranium, whereas thorium was strongly favored at steady-state), because used present-day fuel is disposed without being recycled given that uranium-233, rather than plutonium, is the primarily fissile nuclide at the closed thorium fuel cycle's steady-state. Resource consumption was the only metric was strongly influenced by the specific transition pathway selected, favoring those pathways that more quickly arrived at steady-state through higher breeding ratio assumptions regardless of whether thorium or uranium was used.

Comparative life cycle assessments: The case of paper and digital media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bull, Justin G., E-mail: jgbull@gmail.com; Kozak, Robert A., E-mail: rob.kozak@ubc.ca

The consumption of the written word is changing, as media transitions from paper products to digital alternatives. We reviewed the life cycle assessment (LCA) research literature that compared the environmental footprint of digital and paper media. To validate the role of context in influencing LCA results, we assessed LCAs that did not compare paper and print, but focused on a product or component that is part of the Information and Communication Technology (ICT) sector. Using a framework that identifies problems in LCA conduct, we assessed whether the comparative LCAs were accurate expressions of the environmental footprints of paper and print.more » We hypothesized that the differences between the product systems that produce paper and digital media weaken LCA's ability to compare environmental footprints. We also hypothesized that the characteristics of ICT as an industrial sector weaken LCA as an environmental assessment methodology. We found that existing comparative LCAs offered problematic comparisons of paper and digital media for two reasons — the stark material differences between ICT products and paper products, and the unique characteristics of the ICT sector. We suggested that the context of the ICT sector, best captured by the concept of “Moore's Law”, will continuously impede the ability of the LCA methodology to measure ICT products. -- Highlights: • We review the LCA research that compares paper and digital media. • We contrast the comparative LCAs with LCAs that examine only digital products. • Stark differences between paper and digital media weakens LCA findings. • Digital products in general challenge the LCA method's reliability. • Continuous innovation and global nature of digital products impedes LCA methodology.« less

Performance assessment of an irreversible nano Brayton cycle operating with Maxwell-Boltzmann gas

NASA Astrophysics Data System (ADS)

Açıkkalp, Emin; Caner, Necmettin

2015-05-01

In the last decades, nano-technology has been developed very fast. According to this, nano-cycle thermodynamics should improve with a similar rate. In this paper, a nano-scale irreversible Brayton cycle working with helium is evaluated for different thermodynamic criteria. These are maximum work output, ecological function, ecological coefficient of performance, exergetic performance criteria and energy efficiency. Thermodynamic analysis was performed for these criteria and results were submitted numerically. In addition, these criteria are compared with each other and the most convenient methods for the optimum conditions are suggested.

Sex and menstrual cycle influences on three aspects of attention.

PubMed

Pletzer, Belinda; Harris, Ti-Anni; Ortner, Tuulia

2017-10-01

Sex differences and menstrual cycle influences have been investigated in a variety of cognitive abilities, but results regarding attention are comparably sparse. In the present study, 35 men and 32 naturally cycling women completed three attention tasks, which are commonly used in neuropsychological assessment situations. All participants completed two sessions, which were time-locked to the follicular (low progesterone) and luteal cycle phase (high progesterone) in women. The results reveal higher operation speed during sustained attention in men, but no sex differences in selected and divided attention. Menstrual cycle influences were observed on accuracy in all three tasks. During divided and sustained attention, for which a male advantage was previously reported, accuracy was higher during the early follicular compared to the mid-luteal cycle phase. Furthermore, during selected and sustained attention the learning effect from the first to the second test session was higher in women who started the experiment in their luteal cycle phase. These results suggest a possible role of progesterone in modulating the ability to focus on certain stimulus aspects, while inhibiting others and to sustain attention over a longer period of time. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

The life cycle assessment of cellulose pulp from waste cotton via the SaXcell™ process.

NASA Astrophysics Data System (ADS)

Oelerich, Jens; Bijleveld, Marijn; Bouwhuis, Gerrit H.; Brinks, Ger J.

2017-10-01

Recycling of cotton waste into high value products is a longstanding goal in textile research. The SaXcellTM process provides a chemical recycling route towards virgin fibres. In this study a Life cycle assessment (LCA) is conducted to measure the impact of the chemical recycling of cotton waste on the environment. Pure cotton waste and cotton containing 10 % of polyester are elaborated. The results show that chemical recycling via the SaXcellTM process can have a lower impact on climate change and other impact category than comparable pulping technologies.

Accounting for the Variation of Driver Aggression in the Simulation of Conventional and Advanced Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neubauer, J.; Wood, E.

2013-01-01

Hybrid electric vehicles, plug-in hybrid electric vehicles, and battery electric vehicles offer the potential to reduce both oil imports and greenhouse gases, as well as to offer a financial benefit to the driver. However, assessing these potential benefits is complicated by several factors, including the driving habits of the operator. We focus on driver aggression, i.e., the level of acceleration and velocity characteristic of travel, to (1) assess its variation within large, real-world drive datasets, (2) quantify its effect on both vehicle efficiency and economics for multiple vehicle types, (3) compare these results to those of standard drive cycles commonlymore » used in the industry, and (4) create a representative drive cycle for future analyses where standard drive cycles are lacking.« less

Mobile phone use while cycling: incidence and effects on behaviour and safety.

PubMed

de Waard, Dick; Schepers, Paul; Ormel, Wieke; Brookhuis, Karel

2010-01-01

The effects of mobile phone use on cycling behaviour were studied. In study 1, the prevalence of mobile phone use while cycling was assessed. In Groningen 2.2% of cyclists were observed talking on their phone and 0.6% were text messaging or entering a phone number. In study 2, accident-involved cyclists responded to a questionnaire. Only 0.5% stated that they were using their phone at the time of the accident. In study 3, participants used a phone while cycling. The content of the conversation was manipulated and participants also had to enter a text message. Data were compared with just cycling and cycling while listening to music. Telephoning coincided with reduced speed, reduced peripheral vision performance and increased risk and mental effort ratings. Text messaging had the largest negative impact on cycling performance. Higher mental workload and lower speed may account for the relatively low number of people calling involved in accidents. STATEMENT OF RELEVANCE: Although perhaps mainly restricted to flat countries with a large proportion of cyclists, mobile phone use while cycling has increased and may be a threat to traffic safety, similar to phone use while driving a car. In this study, the extent of the problem was assessed by observing the proportion of cyclists using mobile phones, sending questionnaires to accident-involved cyclists and an experimental study was conducted on the effects of mobile phone use while cycling.

Environmental modelling of use of treated organic waste on agricultural land: a comparison of existing models for life cycle assessment of waste systems.

PubMed

Hansen, Trine Lund; Christensen, Thomas Højlund; Schmidt, Sonia

2006-04-01

Modelling of environmental impacts from the application of treated organic municipal solid waste (MSW) in agriculture differs widely between different models for environmental assessment of waste systems. In this comparative study five models were examined concerning quantification and impact assessment of environmental effects from land application of treated organic MSW: DST (Decision Support Tool, USA), IWM (Integrated Waste Management, U.K.), THE IFEU PROJECT (Germany), ORWARE (ORganic WAste REsearch, Sweden) and EASEWASTE (Environmental Assessment of Solid Waste Systems and Technologies, Denmark). DST and IWM are life cycle inventory (LCI) models, thus not performing actual impact assessment. The DST model includes only one water emission (biological oxygen demand) from compost leaching in the results and IWM considers only air emissions from avoided production of commercial fertilizers. THE IFEU PROJECT, ORWARE and EASEWASTE are life cycle assessment (LCA) models containing more detailed land application modules. A case study estimating the environmental impacts from land application of 1 ton of composted source sorted organic household waste was performed to compare the results from the different models and investigate the origin of any difference in type or magnitude of the results. The contributions from the LCI models were limited and did not depend on waste composition or local agricultural conditions. The three LCA models use the same overall approach for quantifying the impacts of the system. However, due to slightly different assumptions, quantification methods and environmental impact assessment, the obtained results varied clearly between the models. Furthermore, local conditions (e.g. soil type, farm type, climate and legal regulation) and waste composition strongly influenced the results of the environmental assessment.

A comparison between the multimedia fate and exposure models CalTOX and uniform system for evaluation of substances adapted for life-cycle assessment based on the population intake fraction of toxic pollutants.

PubMed

Huijbregts, Mark A J; Geelen, Loes M J; Hertwich, Edgar G; McKone, Thomas E; van de Meent, Dik

2005-02-01

In life-cycle assessment (LCA) and comparative risk assessment, potential human exposure to toxic pollutants can be expressed as the population intake fraction (iF), which represents the fraction of the quantity emitted that enters the human population. To assess the influence of model differences in the calculation of the population iF ingestion and inhalation iFs of 365 substances emitted to air, freshwater, and soil were calculated with two commonly applied multimedia fate and exposure models, CalTOX and the uniform system for evaluation of substances adapted for life-cycle assessment (USES-LCA). The model comparison showed that differences in the iFs due to model choices were the lowest after emission to air and the highest after emission to soil. Inhalation iFs were more sensitive to model differences compared to ingestion iFs. The choice for a continental seawater compartment, vertical stratification of the soil compartment, rain and no-rain scenarios, and drinking water purification mainly clarify the relevant model differences found in population iFs. Furthermore, pH correction of chemical properties and aerosol-associated deposition on plants appeared to be important for dissociative organics and metals emitted to air, respectively. Finally, it was found that quantitative structure-activity relationship estimates for superhydrophobics may introduce considerable uncertainty in the calculation of population intake fractions.

Evaluating uncertainty in environmental life-cycle assessment. A case study comparing two insulation options for a Dutch one-family dwelling.

PubMed

Huijbregts, Mark A J; Gilijamse, Wim; Ragas, Ad M J; Reijnders, Lucas

2003-06-01

The evaluation of uncertainty is relatively new in environmental life-cycle assessment (LCA). It provides useful information to assess the reliability of LCA-based decisions and to guide future research toward reducing uncertainty. Most uncertainty studies in LCA quantify only one type of uncertainty, i.e., uncertainty due to input data (parameter uncertainty). However, LCA outcomes can also be uncertain due to normative choices (scenario uncertainty) and the mathematical models involved (model uncertainty). The present paper outlines a new methodology that quantifies parameter, scenario, and model uncertainty simultaneously in environmental life-cycle assessment. The procedure is illustrated in a case study that compares two insulation options for a Dutch one-family dwelling. Parameter uncertainty was quantified by means of Monte Carlo simulation. Scenario and model uncertainty were quantified by resampling different decision scenarios and model formulations, respectively. Although scenario and model uncertainty were not quantified comprehensively, the results indicate that both types of uncertainty influence the case study outcomes. This stresses the importance of quantifying parameter, scenario, and model uncertainty simultaneously. The two insulation options studied were found to have significantly different impact scores for global warming, stratospheric ozone depletion, and eutrophication. The thickest insulation option has the lowest impact on global warming and eutrophication, and the highest impact on stratospheric ozone depletion.

Effect of a puzzle on the process of students' learning about cardiac physiology.

PubMed

Cardozo, Lais Tono; Miranda, Aline Soares; Moura, Maria José Costa Sampaio; Marcondes, Fernanda Klein

2016-09-01

The aim of the present study was to evaluate the effects of using a puzzle to learn about cardiac physiology. Students were divided into control and game groups. In class 1, the control group had a 2-h theoretical class about cardiac physiology, including a detailed description of the phases of the cardiac cycle, whereas the game group had a 50-min theoretical class without the description of the cardiac cycle. In class 2, the control group did an assessment exercise before an activity with the cardiac puzzle and the game group answered questions after the above-mentioned activity. While solving the puzzle, the students had to describe the cardiac cycle by relating the concepts of heart morphology and physiology. To evaluate short-term learning, the number of wrong answers and grades in the assessment exercise were compared between the control and game groups. To evaluate medium-term learning, we compared the grades obtained by students of the control and game groups in questions about cardiac physiology that formed part of the academic exam. In the assessment exercise, the game group presented a lower number of errors and higher score compared with the control group. In the academic exam, applied after both groups had used the puzzle, there was no difference in the scores obtained by the control and game groups in questions about cardiac physiology. These results showed a positive effect of the puzzle on students' learning about cardiac physiology compared with those not using the puzzle. Copyright © 2016 The American Physiological Society.

Life cycle analysis on fossil energy ratio of algal biodiesel: effects of nitrogen deficiency and oil extraction technology.

PubMed

Jian, Hou; Jing, Yang; Peidong, Zhang

2015-01-01

Life cycle assessment (LCA) has been widely used to analyze various pathways of biofuel preparation from "cradle to grave." Effects of nitrogen supply for algae cultivation and technology of algal oil extraction on life cycle fossil energy ratio of biodiesel are assessed in this study. Life cycle fossil energy ratio of Chlorella vulgaris based biodiesel is improved by growing algae under nitrogen-limited conditions, while the life cycle fossil energy ratio of biodiesel production from Phaeodactylum tricornutum grown with nitrogen deprivation decreases. Compared to extraction of oil from dried algae, extraction of lipid from wet algae with subcritical cosolvents achieves a 43.83% improvement in fossil energy ratio of algal biodiesel when oilcake drying is not considered. The outcome for sensitivity analysis indicates that the algal oil conversion rate and energy content of algae are found to have the greatest effects on the LCA results of algal biodiesel production, followed by utilization ratio of algal residue, energy demand for algae drying, capacity of water mixing, and productivity of algae.

Life Cycle Analysis on Fossil Energy Ratio of Algal Biodiesel: Effects of Nitrogen Deficiency and Oil Extraction Technology

PubMed Central

Jian, Hou; Jing, Yang; Peidong, Zhang

2015-01-01

Life cycle assessment (LCA) has been widely used to analyze various pathways of biofuel preparation from “cradle to grave.” Effects of nitrogen supply for algae cultivation and technology of algal oil extraction on life cycle fossil energy ratio of biodiesel are assessed in this study. Life cycle fossil energy ratio of Chlorella vulgaris based biodiesel is improved by growing algae under nitrogen-limited conditions, while the life cycle fossil energy ratio of biodiesel production from Phaeodactylum tricornutum grown with nitrogen deprivation decreases. Compared to extraction of oil from dried algae, extraction of lipid from wet algae with subcritical cosolvents achieves a 43.83% improvement in fossil energy ratio of algal biodiesel when oilcake drying is not considered. The outcome for sensitivity analysis indicates that the algal oil conversion rate and energy content of algae are found to have the greatest effects on the LCA results of algal biodiesel production, followed by utilization ratio of algal residue, energy demand for algae drying, capacity of water mixing, and productivity of algae. PMID:26000338

Greater Reduction of Balance as a Result of Increased Plantar Fascia Elasticity at Ovulation during the Menstrual Cycle.

PubMed

Petrofsky, Jerrold; Lee, Haneul

2015-11-01

One of the sexual hormones, estrogen, increases elasticity of human connective tissue such as the anterior cruciate ligament during the menstrual cycle in women. In the present investigation, the plantar fascia was investigated to see if there is a difference in elasticity with the menstrual cycle. Fifteen young healthy females in the age range of 18-35 years old with a regular menstrual cycle were tested twice throughout one full menstrual cycle; once during the early follicular phases and once at ovulation. Foot length, while standing on both feet and one foot were used to assess plantar fascia elasticity, ultrasound measured plantar fascia thickness while lying and standing, and posture sway and tremor using a balance platform during 8 different balance tests were assessed to see the impact of elasticity changes. Foot length increased significantly at ovulation compared to menstruation when standing on two feet (p = 0.03) and standing on one foot (p < 0.001). There was also a significant increase in plantar fascia in thinning per kilogram weight applied to the foot at ovulation compared to menstruation (p = 0.014). Associated with this increase in elasticity at ovulation, there was a reduction in balance in the most difficult balance tasks and an increase in tremor during ovulation (p < 0.05). Plantar fascia elasticity change during the menstrual cycle might have effects on posture sway and tremor, which could have a potential risk of falling. Therefore, healthy professionals working with young female adults should recognize these physiological effects.

Tubal Factor Infertility and Perinatal Risk After Assisted Reproductive Technology

PubMed Central

Kawwass, Jennifer F.; Crawford, Sara; Kissin, Dmitry M.; Session, Donna R.; Boulet, Sheree; Jamieson, Denise J.

2014-01-01

OBJECTIVE To assess trends of tubal factor infertility and to evaluate risk of miscarriage and delivery of preterm or low birth weight (LBW) neonates among women with tubal factor infertility using assisted reproductive technology (ART). METHODS We assessed trends of tubal factor infertility among all fresh and frozen, donor, and nondonor ART cycles performed annually in the United States between 2000 and 2010 (N=1,418,774) using the National ART Surveillance System. The data set was then limited to fresh, nondonor in vitro fertilization cycles resulting in pregnancy to compare perinatal outcomes for cycles associated with tubal compared with male factor infertility. We performed bivariate and multivariable analyses controlling for maternal characteristics and calculated adjusted risk ratios (RRs) and 95% confidence intervals (CI). RESULTS The percentage of ART cycles associated with tubal factor infertility diagnoses decreased from 2000 to 2010 (26.02–14.81%). Compared with male factor infertility, tubal factor portended an increased risk of miscarriage (14.0% compared with 12.7%, adjusted RR 1.08, 95% CI 1.04–1.12); risk was increased for both early and late miscarriage. Singleton neonates born to women with tubal factor infertility had an increased risk of pre-term birth (15.8% compared with 11.6%, adjusted RR 1.27, 95% CI 1.20–1.34) and LBW (10.9% compared with 8.5%, adjusted RR 1.28, 95% CI 1.20–1.36). Significant increases in risk persisted for early and late preterm delivery and very low and moderately LBW delivery. A significantly elevated risk was also detected for twin, but not triplet, pregnancies. CONCLUSION Tubal factor infertility, which is decreasing in prevalence in the United States, is associated with an increased risk of miscarriage, preterm birth, and LBW delivery as compared with couples with male factor infertility using ART. PMID:23812461

Life Cycle Assessment and Release Studies for 15 Nanosilver-Enabled Consumer Products: Investigating Hotspots and Patterns of Contribution.

PubMed

Pourzahedi, Leila; Vance, Marina; Eckelman, Matthew J

2017-06-20

Increasing use of silver nanoparticles (AgNPs) in consumer products as antimicrobial agents has prompted extensive research toward the evaluation of their potential release to the environment and subsequent ecotoxicity to aquatic organisms. It has also been shown that AgNPs can pose significant burdens to the environment from life cycle emissions associated with their production, but these impacts must be considered in the context of actual products that contain nanosilver. Here, a cradle-to-gate life cycle assessment for the production of 15 different AgNP-enabled consumer products was performed, coupled with release studies of those same products, thus providing a consistent analytical platform for investigation of potential nanosilver impacts across a range of product types and concentrations. Environmental burdens were assessed over multiple impact categories defined by the United States Environmental Protection Agency's Tool for the Reduction and Assessment of Chemical and Other Environmental Impacts (TRACI 2.1) method. Depending on the product composition and silver loading, the contribution of AgNP synthesis to the overall impacts was seen to vary over a wide range from 1% to 99%. Release studies found that solid polymeric samples lost more silver during wash compared to fibrous materials. Estimates of direct ecotoxicity impacts of AgNP releases from those products with the highest leaching rates resulted in lower impact levels compared to cradle-to-gate ecotoxicity from production for those products. Considering both cradle-to-gate production impacts and nanoparticle release studies, in conjunction with estimates of life cycle environmental and health benefits of nanoparticle incorporation, can inform sustainable nanoenabled product design.

NASA welding assessment program

NASA Technical Reports Server (NTRS)

Stofel, E. J.

1984-01-01

A long duration test was conducted for comparing various methods of attaching electrical interconnects to solar cells for near Earth orbit spacecraft. Representative solar array modules were thermally cycled for 36,000 cycles between -80 and +80 C. The environmental stress of more than 6 years on a near Earth spacecraft as it cycles in and out of the earth's shadow was simulated. Evaluations of the integrity of these modules were made by visual and by electrical examinations before starting the cycling and then at periodic intervals during the cycling tests. Modules included examples of parallel gap and of ultrasonic welding, as well as soldering. The materials and fabrication processes are state of the art, suitable for forming large solar arrays of spacecraft quality. The modules survived this extensive cycling without detectable degradation in their ability to generate power under sunlight illumination.

Life cycle assessment of gas atomised sponge nickel for use in alkaline hydrogen fuel cell applications

NASA Astrophysics Data System (ADS)

Wilson, Benjamin P.; Lavery, Nicholas P.; Jarvis, David J.; Anttila, Tomi; Rantanen, Jyri; Brown, Stephen G. R.; Adkins, Nicholas J.

2013-12-01

This paper presents a cradle-to-grave comparative Life Cycle Assessment (LCA) of new gas atomised (GA) sponge nickel catalysts and evaluates their performance against the both cast and crush (CC) sponge nickel and platinum standards currently used in commercial alkaline fuel cells (AFC). The LCA takes into account the energy used and emissions throughout the entire life cycle of sponge nickel catalysts - ranging from the upstream production of materials (mainly aluminium and nickel), to the manufacturing, to the operation and finally to the recycling and disposal. Through this assessment it was found that the energy and emissions during the operational phase associated with a given catalyst considerably outweigh the primary production, manufacturing and recycling. Primary production of the nickel (and to a lesser extent dopant materials) also has a significant environmental impact but this is offset by operational energy savings over the electrode's estimated lifetime and end of life recyclability. From the results it can be concluded that higher activity spongy nickel catalysts produced by gas atomisation could have a significantly lower environmental impact than either CC nickel or platinum. Doped GA sponge nickel in particular showed comparable performance to that of the standard platinum electrode used in AFCs.

Comparative life cycle assessment of lignocellulosic ethanol production: biochemical versus thermochemical conversion.

PubMed

Mu, Dongyan; Seager, Thomas; Rao, P Suresh; Zhao, Fu

2010-10-01

Lignocellulosic biomass can be converted into ethanol through either biochemical or thermochemical conversion processes. Biochemical conversion involves hydrolysis and fermentation while thermochemical conversion involves gasification and catalytic synthesis. Even though these routes produce comparable amounts of ethanol and have similar energy efficiency at the plant level, little is known about their relative environmental performance from a life cycle perspective. Especially, the indirect impacts, i.e. emissions and resource consumption associated with the production of various process inputs, are largely neglected in previous studies. This article compiles material and energy flow data from process simulation models to develop life cycle inventory and compares the fossil fuel consumption, greenhouse gas emissions, and water consumption of both biomass-to-ethanol production processes. The results are presented in terms of contributions from feedstock, direct, indirect, and co-product credits for four representative biomass feedstocks i.e., wood chips, corn stover, waste paper, and wheat straw. To explore the potentials of the two conversion pathways, different technological scenarios are modeled, including current, 2012 and 2020 technology targets, as well as different production/co-production configurations. The modeling results suggest that biochemical conversion has slightly better performance on greenhouse gas emission and fossil fuel consumption, but that thermochemical conversion has significantly less direct, indirect, and life cycle water consumption. Also, if the thermochemical plant operates as a biorefinery with mixed alcohol co-products separated for chemicals, it has the potential to achieve better performance than biochemical pathway across all environmental impact categories considered due to higher co-product credits associated with chemicals being displaced. The results from this work serve as a starting point for developing full life cycle assessment model that facilitates effective decision-making regarding lignocellulosic ethanol production.

Comparative Life Cycle Assessment of Lignocellulosic Ethanol Production: Biochemical Versus Thermochemical Conversion

NASA Astrophysics Data System (ADS)

Mu, Dongyan; Seager, Thomas; Rao, P. Suresh; Zhao, Fu

2010-10-01

Lignocellulosic biomass can be converted into ethanol through either biochemical or thermochemical conversion processes. Biochemical conversion involves hydrolysis and fermentation while thermochemical conversion involves gasification and catalytic synthesis. Even though these routes produce comparable amounts of ethanol and have similar energy efficiency at the plant level, little is known about their relative environmental performance from a life cycle perspective. Especially, the indirect impacts, i.e. emissions and resource consumption associated with the production of various process inputs, are largely neglected in previous studies. This article compiles material and energy flow data from process simulation models to develop life cycle inventory and compares the fossil fuel consumption, greenhouse gas emissions, and water consumption of both biomass-to-ethanol production processes. The results are presented in terms of contributions from feedstock, direct, indirect, and co-product credits for four representative biomass feedstocks i.e., wood chips, corn stover, waste paper, and wheat straw. To explore the potentials of the two conversion pathways, different technological scenarios are modeled, including current, 2012 and 2020 technology targets, as well as different production/co-production configurations. The modeling results suggest that biochemical conversion has slightly better performance on greenhouse gas emission and fossil fuel consumption, but that thermochemical conversion has significantly less direct, indirect, and life cycle water consumption. Also, if the thermochemical plant operates as a biorefinery with mixed alcohol co-products separated for chemicals, it has the potential to achieve better performance than biochemical pathway across all environmental impact categories considered due to higher co-product credits associated with chemicals being displaced. The results from this work serve as a starting point for developing full life cycle assessment model that facilitates effective decision-making regarding lignocellulosic ethanol production.

Life cycle assessment of carbon dioxide for different arboricultural practices in Los Angeles, CA

Treesearch

E. Gregory McPherson; Alissa Kendall; Shannon Albers

2015-01-01

Although the arboriculture industry plants and maintains trees that remove CO2 from the atmosphere, it uses heavy-duty equipment and vehicles that release more CO2 per year than other similar-sized industries in the service sector. This study used lifecycle assessment to compare CO2 emissions...

Illustrative national scale scenarios of environmental and human health impacts of Carbon Capture and Storage.

PubMed

Tzanidakis, Konstantinos; Oxley, Tim; Cockerill, Tim; ApSimon, Helen

2013-06-01

Integrated Assessment, and the development of strategies to reduce the impacts of air pollution, has tended to focus only upon the direct emissions from different sources, with the indirect emissions associated with the full life-cycle of a technology often overlooked. Carbon Capture and Storage (CCS) reflects a number of new technologies designed to reduce CO2 emissions, but which may have much broader environmental implications than greenhouse gas emissions. This paper considers a wider range of pollutants from a full life-cycle perspective, illustrating a methodology for assessing environmental impacts using source-apportioned effects based impact factors calculated by the national scale UK Integrated Assessment Model (UKIAM). Contrasting illustrative scenarios for the deployment of CCS towards 2050 are presented which compare the life-cycle effects of air pollutant emissions upon human health and ecosystems of business-as-usual, deployment of CCS and widespread uptake of IGCC for power generation. Together with estimation of the transboundary impacts we discuss the benefits of an effects based approach to such assessments in relation to emissions based techniques. Copyright © 2013 Elsevier Ltd. All rights reserved.

Variability in Light-Duty Gasoline Vehicle Emission Factors from Trip-Based Real-World Measurements.

PubMed

Liu, Bin; Frey, H Christopher

2015-10-20

Using data obtained with portable emissions measurements systems (PEMS) on multiple routes for 100 gasoline vehicles, including passenger cars (PCs), passenger trucks (PTs), and hybrid electric vehicles (HEVs), variability in tailpipe emission rates was evaluated. Tier 2 emission standards are shown to be effective in lowering NOx, CO, and HC emission rates. Although PTs are larger, heavier vehicles that consume more fuel and produce more CO2 emissions, they do not necessarily produce more emissions of regulated pollutants compared to PCs. HEVs have very low emission rates compared to tier 2 vehicles under real-world driving. Emission factors vary with cycle average speed and road type, reflecting the combined impact of traffic control and traffic congestion. Compared to the slowest average speed and most congested cycles, optimal emission rates could be 50% lower for CO2, as much as 70% lower for NOx, 40% lower for CO, and 50% lower for HC. There is very high correlation among vehicles when comparing driving cycles. This has implications for how many cycles are needed to conduct comparisons between vehicles, such as when comparing fuels or technologies. Concordance between empirical and predicted emission rates using the U.S. Environmental Protection Agency's MOVES model was also assessed.

Comparative analysis of gas and coal-fired power generation in ultra-low emission condition using life cycle assessment (LCA)

NASA Astrophysics Data System (ADS)

Yin, Libao; Liao, Yanfen; Liu, Guicai; Liu, Zhichao; Yu, Zhaosheng; Guo, Shaode; Ma, Xiaoqian

2017-05-01

Energy consumption and pollutant emission of natural gas combined cycle power-generation (NGCC), liquefied natural gas combined cycle power-generation (LNGCC), natural gas combined heat and power generation (CHP) and ultra-supercritical power generation with ultra-low gas emission (USC) were analyzed using life cycle assessment method, pointing out the development opportunity and superiority of gas power generation in the period of coal-fired unit ultra-low emission transformation. The results show that CO2 emission followed the order: USC>LNGCC>NGCC>CHP the resource depletion coefficient of coal-fired power generation was lower than that of gas power generation, and the coal-fired power generation should be the main part of power generation in China; based on sensitivity analysis, improving the generating efficiency or shortening the transportation distance could effectively improve energy saving and emission reduction, especially for the coal-fired units, and improving the generating efficiency had a great significance for achieving the ultra-low gas emission.

Life cycle assessment of nuclear-based hydrogen production via thermochemical water splitting using a copper-chlorine (Cu-Cl) cycle

NASA Astrophysics Data System (ADS)

Ozbilen, Ahmet Ziyaettin

The energy carrier hydrogen is expected to solve some energy challenges. Since its oxidation does not emit greenhouse gases (GHGs), its use does not contribute to climate change, provided that it is derived from clean energy sources. Thermochemical water splitting using a Cu-Cl cycle, linked with a nuclear super-critical water cooled reactor (SCWR), which is being considered as a Generation IV nuclear reactor, is a promising option for hydrogen production. In this thesis, a comparative environmental study is reported of the three-, four- and five-step Cu-Cl thermochemical water splitting cycles with various other hydrogen production methods. The investigation uses life cycle assessment (LCA), which is an analytical tool to identify and quantify environmentally critical phases during the life cycle of a system or a product and/or to evaluate and decrease the overall environmental impact of the system or product. The LCA results for the hydrogen production processes indicate that the four-step Cu-Cl cycle has lower environmental impacts than the three- and five-step Cu-Cl cycles due to its lower thermal energy requirement. Parametric studies show that acidification potentials (APs) and global warming potentials (GWPs) for the four-step Cu-Cl cycle can be reduced from 0.0031 to 0.0028 kg SO2-eq and from 0.63 to 0.55 kg CO2-eq, respectively, if the lifetime of the system increases from 10 to 100 years. Moreover, the comparative study shows that the nuclear-based S-I and the four-step Cu-Cl cycles are the most environmentally benign hydrogen production methods in terms of AP and GWP. GWPs of the S-I and the four-step Cu-Cl cycles are 0.412 and 0.559 kg CO2-eq for reference case which has a lifetime of 60 years. Also, the corresponding APs of these cycles are 0.00241 and 0.00284 kg SO2-eq. It is also found that an increase in hydrogen plant efficiency from 0.36 to 0.65 decreases the GWP from 0.902 to 0.412 kg CO 2-eq and the AP from 0.00459 to 0.00209 kg SO2-eq for the four-step Cu-Cl cycle. Keywords: Hydrogen production, nuclear energy, Cu-Cl cycle, environmental impact, LCA.

Accounting for the Variation of Driver Aggression in the Simulation of Conventional and Advanced Vehicles: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neubauer, J.; Wood, E.

2013-03-01

Hybrid electric vehicles, plug-in hybrid electric vehicles, and battery electric vehicles offer the potential to reduce both oil imports and greenhouse gases, as well as to offer a financial benefit to the driver. However, assessing these potential benefits is complicated by several factors, including the driving habits of the operator. We focus on driver aggression, i.e., the level of acceleration and velocity characteristic of travel, to (1) assess its variation within large, real-world drive datasets, (2) quantify its effect on both vehicle efficiency and economics for multiple vehicle types, (3) compare these results to those of standard drive cycles commonlymore » used in the industry, and (4) create a representative drive cycle for future analyses where standard drive cycles are lacking.« less

Prevention of endometrial apoptosis: randomized prospective comparison of human chorionic gonadotropin versus progesterone treatment in the luteal phase.

PubMed

Lovely, Laurie P; Fazleabas, Asgerally T; Fritz, Marc A; McAdams, Devin G; Lessey, Bruce A

2005-04-01

To study control of apoptosis in human endometrium, we examined late luteal-phase endometrial biopsies obtained in the late luteal phase for evidence of apoptosis and compared the effects of exogenous human chorionic gonadotropin (hCG) and progesterone on this process. Using a controlled, prospective, and randomized study design, 12 healthy, fertile, reproductive-age women (ages 20-34 yr) with regular menstrual cycles (range, 26-32 d) were recruited. Each underwent an endometrial biopsy 12 d after a urinary LH surge in a control and treatment cycle. After biopsy in a natural cycle, subjects were randomized to receive luteal doses of either 200 mg intravaginal progesterone (d 18-27) or a single im injection of 10,000 IU of hCG (d 19) followed by repeat endometrial biopsy and collection of serum on d 26. Apoptosis was assessed by DNA laddering, localizing apoptotic bodies using immunofluorescent labeling of DNA fragments (the terminal deoxynucleotidyl transferase-mediated dUTP nick-end labeling method), and immunohistochemical assessment of apoptosis markers bcl-2, bcl-x, and bax. Serum progesterone levels were compared between treatment groups. Evidence of apoptosis in control cycles was significantly reduced in endometrium after both luteal-phase treatments. The terminal deoxynucleotidyl transferase-mediated dUTP nick-end-labeling results demonstrated significantly less apoptosis in the hCG treatment group compared with controls. Immunostaining for bcl-2 was higher in hCG- and progesterone-treated cycles, whereas bax expression was decreased and bcl-x immunostaining was not different between treatments. Serum progesterone levels were highest in the hCG-treated group, although statistical significance was not reached (P = 0.08). These results demonstrate that signs of apoptosis, already apparent by d 26 of the menstrual cycle can be reduced with either hCG or progesterone treatment. The clinical utility of these findings includes a rational use of luteal-phase support for treatment of women with infertility and/or recurrent pregnancy loss.

Life cycle water consumption and wastewater generation impacts of a Marcellus shale gas well.

PubMed

Jiang, Mohan; Hendrickson, Chris T; VanBriesen, Jeanne M

2014-01-01

This study estimates the life cycle water consumption and wastewater generation impacts of a Marcellus shale gas well from its construction to end of life. Direct water consumption at the well site was assessed by analysis of data from approximately 500 individual well completion reports collected in 2010 by the Pennsylvania Department of Conservation and Natural Resources. Indirect water consumption for supply chain production at each life cycle stage of the well was estimated using the economic input-output life cycle assessment (EIO-LCA) method. Life cycle direct and indirect water quality pollution impacts were assessed and compared using the tool for the reduction and assessment of chemical and other environmental impacts (TRACI). Wastewater treatment cost was proposed as an additional indicator for water quality pollution impacts from shale gas well wastewater. Four water management scenarios for Marcellus shale well wastewater were assessed: current conditions in Pennsylvania; complete discharge; direct reuse and desalination; and complete desalination. The results show that under the current conditions, an average Marcellus shale gas well consumes 20,000 m(3) (with a range from 6700 to 33,000 m(3)) of freshwater per well over its life cycle excluding final gas utilization, with 65% direct water consumption at the well site and 35% indirect water consumption across the supply chain production. If all flowback and produced water is released into the environment without treatment, direct wastewater from a Marcellus shale gas well is estimated to have 300-3000 kg N-eq eutrophication potential, 900-23,000 kg 2,4D-eq freshwater ecotoxicity potential, 0-370 kg benzene-eq carcinogenic potential, and 2800-71,000 MT toluene-eq noncarcinogenic potential. The potential toxicity of the chemicals in the wastewater from the well site exceeds those associated with supply chain production, except for carcinogenic effects. If all the Marcellus shale well wastewater is treated to surface discharge standards by desalination, $59,000-270,000 per well would be required. The life cycle study results indicate that when gas end use is not considered hydraulic fracturing is the largest contributor to the life cycle water impacts of a Marcellus shale gas well.

Data supporting the comparative life cycle assessment of different municipal solid waste management scenarios

PubMed Central

Ali Rajaeifar, Mohammad; Tabatabaei, Meisam; Ghanavati, Hossein

2015-01-01

Environmental assessment of municipal solid waste (MSW) management scenarios would help to select eco-friendly scenarios. In this study, the inventory data in support of life cycle assessment of different MSW are presented. The scenarios were defined as: anaerobic digestion (AD, Sc-0), landfilling combined with composting (Sc-1), incineration (Sc-2), incineration combined with composting (Sc-3), and AD combined with incineration (Sc-4). The current article contains flowcharts of the different scenarios. Additionally, six supplementary files including inventory data on the different scenarios, data on the different damage assessment categories, normalization, and single scores are presented (Supplementary files 1–6). The analysis of the different scenarios revealed that the most eco-friendly scenario to be implemented in the future would be the combination of AD and incineration (Sc-4). PMID:26217743

Effect of perspiration on skin temperature measurements by infrared thermography and contact thermometry during aerobic cycling

NASA Astrophysics Data System (ADS)

Priego Quesada, Jose Ignacio; Martínez Guillamón, Natividad; Cibrián Ortiz de Anda, Rosa M.^a.; Psikuta, Agnes; Annaheim, Simon; Rossi, René Michel; Corberán Salvador, José Miguel; Pérez-Soriano, Pedro; Salvador Palmer, Rosario

2015-09-01

The aim of the present study was to compare infrared thermography and thermal contact sensors for measuring skin temperature during cycling in a moderate environment. Fourteen cyclists performed a 45-min cycling test at 50% of peak power output. Skin temperatures were simultaneously recorded by infrared thermography and thermal contact sensors before and immediately after cycling activity as well as after 10 min cooling-down, representing different skin wetness and blood perfusion states. Additionally, surface temperature during well controlled dry and wet heat exchange (avoiding thermoregulatory responses) using a hot plate system was assessed by infrared thermography and thermal contact sensors. In human trials, the inter-method correlation coefficient was high when measured before cycling (r = 0.92) whereas it was reduced immediately after the cycling (r = 0.82) and after the cooling-down phase (r = 0.59). Immediately after cycling, infrared thermography provided lower temperature values than thermal contact sensors whereas it presented higher temperatures after the cooling-down phase. Comparable results as in human trials were observed for hot plate tests in dry and wet states. Results support the application of infrared thermography for measuring skin temperature in exercise scenarios where perspiration does not form a water film.

Coupled near-field and far-field exposure assessment framework for chemicals in consumer products.

PubMed

Fantke, Peter; Ernstoff, Alexi S; Huang, Lei; Csiszar, Susan A; Jolliet, Olivier

2016-09-01

Humans can be exposed to chemicals in consumer products through product use and environmental emissions over the product life cycle. Exposure pathways are often complex, where chemicals can transfer directly from products to humans during use or exchange between various indoor and outdoor compartments until sub-fractions reach humans. To consistently evaluate exposure pathways along product life cycles, a flexible mass balance-based assessment framework is presented structuring multimedia chemical transfers in a matrix of direct inter-compartmental transfer fractions. By matrix inversion, we quantify cumulative multimedia transfer fractions and exposure pathway-specific product intake fractions defined as chemical mass taken in by humans per unit mass of chemical in a product. Combining product intake fractions with chemical mass in the product yields intake estimates for use in life cycle impact assessment and chemical alternatives assessment, or daily intake doses for use in risk-based assessment and high-throughput screening. Two illustrative examples of chemicals used in personal care products and flooring materials demonstrate how this matrix-based framework offers a consistent and efficient way to rapidly compare exposure pathways for adult and child users and for the general population. This framework constitutes a user-friendly approach to develop, compare and interpret multiple human exposure scenarios in a coupled system of near-field ('user' environment), far-field and human intake compartments, and helps understand the contribution of individual pathways to overall human exposure in various product application contexts to inform decisions in different science-policy fields for which exposure quantification is relevant. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

NASA welding assessment program

NASA Technical Reports Server (NTRS)

Stofel, E. J.

1984-01-01

A long duration test has been conducted for comparing various methods of attaching electrical interconnects to solar cells for near Earth orbit spacecraft. Representative solar array modules have been thermally cycled for 36,000 cycles between -80 and +80 C on this JPL and NASA Lewis Research Center sponsored work. This test simulates the environmental stress of more than 6 years on a near Earth spacecraft as it cycles in and out of the Earth's shadow. Evaluations of the integrity of these modules were made by visual and by electrical examinations before starting the cycling and then at periodic intervals during the cycling tests. Modules included examples of parallel gap and of ultrasonic welding, as well as soldering. The materials and fabrication processes are state of the art, suitable for forming large solar arrays of spacecraft quality. The modules survived his extensive cycling without detectable degradation in their ability to generate power under sunlight illumination.

Evaluation of undeveloped rocket engine cycle applications to advanced transportation

NASA Technical Reports Server (NTRS)

1990-01-01

Undeveloped pump-fed, liquid propellant rocket engine cycles were assessed and evaluated for application to Next Manned Transportation System (NMTS) vehicles, which would include the evolving Space Transportation System (STS Evolution), the Personnel Launch System (PLS), and the Advanced Manned Launch System (AMLS). Undeveloped engine cycles selected for further analysis had potential for increased reliability, more maintainability, reduced cost, and improved (or possibly level) performance when compared to the existing SSME and proposed STME engines. The split expander (SX) cycle, the full flow staged combustion (FFSC) cycle, and a hybrid version of the FFSC, which has a LOX expander drive for the LOX pump, were selected for definition and analysis. Technology requirements and issues were identified and analyses of vehicle systems weight deltas using the SX and FFSC cycles in AMLS vehicles were performed. A strawman schedule and cost estimate for FFSC subsystem technology developments and integrated engine system demonstration was also provided.

Application of Life Cycle Assessment on Electronic Waste Management: A Review.

PubMed

Xue, Mianqiang; Xu, Zhenming

2017-04-01

Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.

Application of Life Cycle Assessment on Electronic Waste Management: A Review

NASA Astrophysics Data System (ADS)

Xue, Mianqiang; Xu, Zhenming

2017-04-01

Electronic waste is a rich source of both valuable materials and toxic substances. Management of electronic waste is one of the biggest challenges of current worldwide concern. As an effective and prevailing environmental management tool, life cycle assessment can evaluate the environmental performance of electronic waste management activities. Quite a few scientific literatures reporting life cycle assessment of electronic waste management with significant outcomes have been recently published. This paper reviewed the trends, characteristics, research gaps, and challenges of these studies providing detailed information for practitioners involved in electronic waste management. The results showed that life cycle assessment studies were most carried out in Europe, followed by Asia and North America. The research subject of the studies mainly includes monitors, waste printed circuit boards, mobile phones, computers, printers, batteries, toys, dishwashers, and light-emitting diodes. CML was the most widely used life cycle impact assessment method in life cycle assessment studies on electronic waste management, followed by EI99. Furthermore, 40% of the reviewed studies combined with other environmental tools, including life cycle cost, material flow analysis, multi-criteria decision analysis, emergy analysis, and hazard assessment which came to more comprehensive conclusions from different aspects. The research gaps and challenges including uneven distribution of life cycle assessment studies, life cycle impact assessment methods selection, comparison of the results, and uncertainty of the life cycle assessment studies were examined. Although life cycle assessment of electronic waste management facing challenges, their results will play more and more important role in electronic waste management practices.

A Methodology for Robust Comparative Life Cycle Assessments Incorporating Uncertainty.

PubMed

Gregory, Jeremy R; Noshadravan, Arash; Olivetti, Elsa A; Kirchain, Randolph E

2016-06-21

We propose a methodology for conducting robust comparative life cycle assessments (LCA) by leveraging uncertainty. The method evaluates a broad range of the possible scenario space in a probabilistic fashion while simultaneously considering uncertainty in input data. The method is intended to ascertain which scenarios have a definitive environmentally preferable choice among the alternatives being compared and the significance of the differences given uncertainty in the parameters, which parameters have the most influence on this difference, and how we can identify the resolvable scenarios (where one alternative in the comparison has a clearly lower environmental impact). This is accomplished via an aggregated probabilistic scenario-aware analysis, followed by an assessment of which scenarios have resolvable alternatives. Decision-tree partitioning algorithms are used to isolate meaningful scenario groups. In instances where the alternatives cannot be resolved for scenarios of interest, influential parameters are identified using sensitivity analysis. If those parameters can be refined, the process can be iterated using the refined parameters. We also present definitions of uncertainty quantities that have not been applied in the field of LCA and approaches for characterizing uncertainty in those quantities. We then demonstrate the methodology through a case study of pavements.

Reporting in vitro fertilization cycles to the Society for Assisted Reproductive Technology database: where have all the cycles gone?

PubMed

Kulak, David; Jindal, Sangita K; Oh, Cheongeun; Morelli, Sara S; Kratka, Scott; McGovern, Peter G

2016-04-01

To assess the relationship between live birth rates (LBRs) and the incidence of under-reported cycles by IVF clinics. Cohort study. Not applicable. All patients undergoing IVF cycles in the aforementioned clinics. Not applicable. The reporting percentage (RP), defined as number of cycles with reported pregnancy rates divided by total cycles performed. Results from cryopreservation cycles are only presented by SART if an embryo transfer occurs. Thus, RP decreases as incidence of embryo or oocyte banking cycles increases. The LBRs in women aged <35 years were compared between clinics. The median RP of all clinics was 93%-97%. Clinics with RP <80% increased from 2 in 2004 to 30 in 2012. Twenty-one clinics had an RP that fell 2 standard deviations below the mean in any year. Over the 9 years, there was a negative correlation between RP and LBR of -0.17, but for the 21 outlier clinics the correlation increased to -0.26. In 2012 alone, in outlier clinics, for every 10% drop in RP there was an associated rise in LBR of 4.3%; some clinics reported 40% fewer cycles than the median. In clinics with very low RP, the cycles that are reported have higher success rates. Regardless of intent, the reduction of reported data to SART makes it increasingly difficult for clinicians and patients to accurately assess a clinic's success rates. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Transportation life cycle assessment (LCA) synthesis : life cycle assessment learning module series.

DOT National Transportation Integrated Search

2015-03-12

The Life Cycle Assessment Learning Module Series is a set of narrated, self-advancing slideshows on : various topics related to environmental life cycle assessment (LCA). This research project produced the first 27 of such modules, which : are freely...

Bleeding pattern and cycle control of a low-dose transdermal contraceptive patch compared with a combined oral contraceptive: a randomized study.

PubMed

Merz, M; Kroll, R; Lynen, R; Bangerter, K

2015-02-01

The aim of this study was to investigate the bleeding pattern and cycle control of a contraceptive patch containing 0.55 mg ethinyl estradiol (EE) and 2.1 mg gestodene (GSD) compared with a combined oral contraceptive (COC) containing 0.02 mg EE and 0.1 mg levonorgestrel (LNG). In this phase III, randomized, controlled, double-blind, double-dummy, multicenter trial, healthy women aged 18-45 years (smokers aged 18-35 years) received either the EE/GSD patch and a placebo tablet (n=171), or a placebo patch and the COC (n=175) for seven 28-day cycles. Bleeding control was assessed in two 90-day reference periods. Mean number of bleeding/spotting days was comparable across treatment groups in both reference periods (p>.05). Mean number of bleeding/spotting episodes was also comparable in reference period 1; however, there were fewer bleeding/spotting episodes for COC in reference period 2 (3.4 versus 3.1; p=.01). Mean length of bleeding/spotting episodes was comparable across treatment groups for both reference periods (p>.05). Withdrawal bleeding occurred consistently in both groups over the entire treatment period, but its absence was more common in the COC group in cycles 4 and 6 of reference period 2 (p<.01). Intracyclic bleeding was comparable between groups. Bleeding pattern and cycle control with the EE/GSD patch was comparable to an EE/LNG-containing COC. The findings suggest that bleeding patterns with the EE/GSD patch are similar to an EE/LNG-containing COC, except for absence of withdrawal bleeding, which was less common in patch users. The EE/GSD patch may constitute an additional contraceptive option for women. Copyright © 2015 Elsevier Inc. All rights reserved.

Episodic inputs of atmospheric nitrogen to the Sargasso Sea: Contributions to new production and phytoplankton blooms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michaels, A.F.; Johnson, R.J.; Siegel, D.A.

1993-06-01

This paper compares a recent atmospheric wet deposition record (including all measurable daily rainfall events between October 1988 and June 1991) with concurrent measurements of nitrogen cycling and biomass at the U.S. Joint Global Ocean Flux Study Bermuda Atlantic Time Series Study station. The two data sets, among the most complete synoptic records of atmospheric nitrogen deposition and ocean nitrogen cycling, provide an opportunity to directly assess the importance of nitrogen deposition in the ocean. The results indicate that individual nitrogen wet deposition events are usually small compared to the ambient nitrogen cycle and that only under sustained calm conditionsmore » following large deposition events will nitrogen deposition processes be an important signal for the understanding of ocean biochemistry. 46 refs., 7 figs.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pirhonen, P.

Life-cycle assessment is usually based on regular discharges that occur at a more or less constant rate. Nevertheless, the more factors that are taken into account in the LCA the better picture it gives on the environmental aspects of a product. In this study an approach to incorporate accidental releases into a products` life-cycle assessment was developed. In this approach accidental releases are divided into two categories. The first category consists of those unplanned releases which occur with a predicted level and frequency. Due to the high frequency and small release size at a time, these accidental releases can bemore » compared to continuous emissions. Their global impacts are studied in this approach. Accidental releases of the second category are sudden, unplanned releases caused by exceptional situations, e.g. technical failure, action error or disturbances in process conditions. These releases have a singular character and local impacts are typical of them. As far as the accidental releases of the second category are concerned, the approach introduced in this study results in a risk value for every stage of a life-cycle, the sum of which is a risk value for the whole life-cycle. Risk value is based on occurrence frequencies of incidents and potential environmental damage caused by releases. Risk value illustrates the level of potential damage caused by accidental releases related to the system under study and is meant to be used for comparison of these levels of two different products. It can also be used to compare the risk levels of different stages of the life-cycle. An approach was illustrated using petrol as an example product. The whole life-cycle of petrol from crude oil production to the consumption of petrol was studied.« less

Life cycle models of conventional and alternative-fueled automobiles

NASA Astrophysics Data System (ADS)

Maclean, Heather Louise

This thesis reports life cycle inventories of internal combustion engine automobiles with feasible near term fuel/engine combinations. These combinations include unleaded gasoline, California Phase 2 Reformulated Gasoline, alcohol and gasoline blends (85 percent methanol or ethanol combined with 15 percent gasoline), and compressed natural gas in spark ignition direct and indirect injection engines. Additionally, I consider neat methanol and neat ethanol in spark ignition direct injection engines and diesel fuel in compression ignition direct and indirect injection engines. I investigate the potential of the above options to have a lower environmental impact than conventional gasoline-fueled automobiles, while still retaining comparable pricing and consumer benefits. More broadly, the objective is to assess whether the use of any of the alternative systems will help to lead to the goal of a more sustainable personal transportation system. The principal tool is the Economic Input-Output Life Cycle Analysis model which includes inventories of economic data, environmental discharges, and resource use. I develop a life cycle assessment framework to assemble the array of data generated by the model into three aggregate assessment parameters; economics, externalities, and vehicle attributes. The first step is to develop a set of 'comparable cars' with the alternative fuel/engine combinations, based on characteristics of a conventional 1998 gasoline-fueled Ford Taurus sedan, the baseline vehicle for the analyses. I calculate the assessment parameters assuming that these comparable cars can attain the potential thermal efficiencies estimated by experts for each fuel/engine combination. To a first approximation, there are no significant differences in the assessment parameters for the vehicle manufacture, service, fixed costs, and the end-of-life for any of the options. However, there are differences in the vehicle operation life cycle components and the state of technology development for the combinations. Overall, none of the alternatives emerges as a clear winner, lowering the externalities and improving sustainability, while considering technology issues and vehicle attributes. The majority of the alternatives are not likely to displace the baseline automobile. However, the attractiveness of the alternatives depends on the focus of future regulations, government priorities, and technology development. If long-term global sustainability is the principal concern, then improvements in fuel economy alone will not provide the level of reduction in impact required. A switch to renewable fuels (e.g., alcohols or diesel produced from biomass) to power the vehicles will likely be necessary. (Abstract shortened by UMI.)

Menstrual cycle characteristics of young females with occult primary ovarian insufficiency at initial diagnosis and one-year follow-up with serum amh level and antral follicle count

PubMed Central

Guzel, Yilmaz; Aba, Yilda Arzu; Yakin, Kayhan

2017-01-01

Occult primary ovarian insufficiency (also known as incipient ovarian failure or diminished ovarian reserve) is defined as serum AMH level ≤1.1ng/mL in women under age 30. Limited data is available regarding the prevalence of occult POI, the preceding menstrual characteristics and its natural course in otherwise healthy young females. We aimed in this prospective observational study to determine the prevalence of occult POI in young females (< age 30) screened with serum AMH measurement; and analyze the patterns of change in their menstruation at initial assessment and one-year follow-up in relation to the changes in ovarian reserve quantitatively assessed with AMH and AFC. 963 young female college students under age 30 voluntarily participated in this study. 43 of them (4.4%) were diagnosed with occult POI as their AMH levels were ≤ 1.1ng/mL. Thirty-eight (83.4%) of them have regular cycles and denied any menstrual irregularity in the last 12 months. This rate was not statistically different from 7.3% of those with AMH>1.1ng/mL who reported at least one abnormal menstrual cycle in the last year (p = 0.36). Cycle length was significantly shorter in females with AMH ≤ 1.1ng/mL compared to those with AMH>1.1ng/mL (25.1±3.2 vs. 31.2±2.8 respectively, p<0.001). Karyotype, FMR-1 mutation analyses and auto-antibody screening returned normal in all. At one-year follow-up AMH, AFC and mean cycle length were further reduced compared to their values at initial assessment. Now, a greater proportion of the participants with occult POI were menstruating regularly at every 21 days compared to the initial evaluation one year ago (39.5% vs. 13.9% respectively, p = 0.013). Twenty-five underwent oocyte cryopreservation. These findings underscore the importance of screening young females with AMH for possible occult POI. It also emphasizes that young females with critically diminished ovarian reserve may continue to menstruate regularly without any characteristic menstrual abnormality other than shortening of cycle length. PMID:29176793

Menstrual cycle characteristics of young females with occult primary ovarian insufficiency at initial diagnosis and one-year follow-up with serum amh level and antral follicle count.

PubMed

Guzel, Yilmaz; Aba, Yilda Arzu; Yakin, Kayhan; Oktem, Ozgur

2017-01-01

Occult primary ovarian insufficiency (also known as incipient ovarian failure or diminished ovarian reserve) is defined as serum AMH level ≤1.1ng/mL in women under age 30. Limited data is available regarding the prevalence of occult POI, the preceding menstrual characteristics and its natural course in otherwise healthy young females. We aimed in this prospective observational study to determine the prevalence of occult POI in young females (< age 30) screened with serum AMH measurement; and analyze the patterns of change in their menstruation at initial assessment and one-year follow-up in relation to the changes in ovarian reserve quantitatively assessed with AMH and AFC. 963 young female college students under age 30 voluntarily participated in this study. 43 of them (4.4%) were diagnosed with occult POI as their AMH levels were ≤ 1.1ng/mL. Thirty-eight (83.4%) of them have regular cycles and denied any menstrual irregularity in the last 12 months. This rate was not statistically different from 7.3% of those with AMH>1.1ng/mL who reported at least one abnormal menstrual cycle in the last year (p = 0.36). Cycle length was significantly shorter in females with AMH ≤ 1.1ng/mL compared to those with AMH>1.1ng/mL (25.1±3.2 vs. 31.2±2.8 respectively, p<0.001). Karyotype, FMR-1 mutation analyses and auto-antibody screening returned normal in all. At one-year follow-up AMH, AFC and mean cycle length were further reduced compared to their values at initial assessment. Now, a greater proportion of the participants with occult POI were menstruating regularly at every 21 days compared to the initial evaluation one year ago (39.5% vs. 13.9% respectively, p = 0.013). Twenty-five underwent oocyte cryopreservation. These findings underscore the importance of screening young females with AMH for possible occult POI. It also emphasizes that young females with critically diminished ovarian reserve may continue to menstruate regularly without any characteristic menstrual abnormality other than shortening of cycle length.

A Comparative of Life Cycle Assessment of a Conventional Van and a Battery Electric Van for an Online Shopping System in Thailand

NASA Astrophysics Data System (ADS)

Koiwanit, J.; Hamontree, C.

2018-05-01

The transportation sector is responsible for one of the main emitters of large quantities of pollutions to the atmosphere, which impacts local, regional or global environment receptors. In Thailand, many retail chains have been trying to launch many campaigns and projects to reduce GHG emissions together with offering the best convenience services to serve customers’ needs. By promoting an online shopping system for the workplace, this will mitigate even more of the air pollutants than the conventional online shopping system, where the products are delivered to customer’s doorsteps. This study aims to investigate and compare the impact of different vehicle technologies for an online shopping using Life Cycle Assessment (LCA) methodology especially in the vehicle use phase. The observed results showed that the electric van has the potential of reducing emissions and consequently showed lower impacts in most impact categories.

Evaluating the transport, health and economic impacts of new urban cycling infrastructure in Sydney, Australia – protocol paper

PubMed Central

2013-01-01

Background There are repeated calls to build better cycling paths in Australian cities if the proportion of people cycling is to increase. Yet the full range of transport, health, environmental and economic impacts of new cycling infrastructure and the extent to which observed changes are sustained is not well understood. The City of Sydney is currently building a new bicycle network, which includes a new bicycle path separated from road traffic in the south Sydney area. This protocol paper describes a comprehensive method to evaluate this new cycling infrastructure. Method A cohort of residents within two kilometres of the new bicycle path will be surveyed at baseline before a new section of bicycle path is built, and again 12 and 24 months later to assess changes in travel behaviour, sense of community, quality of life and health behaviours. Residents in a comparable area of Sydney that will not get a new separated bike path will act as a comparison group. At baseline a sub-set of residents who volunteer will also take a small GPS device with them for one week to assess travel behaviour. Discussion This research should contribute to the advancement in evaluation and appraisal methods for cycling projects. PMID:24131667

Three Cycles of Radiofrequency Ablation Are More Efficacious Than Two in the Management of Morton's Neuroma.

PubMed

Brooks, David; Parr, Adam; Bryceson, William

2018-04-01

Morton's neuroma is a common cause of forefoot pain. Outcomes of conservative therapy are mixed and many patients undergo operative intervention. Radiofrequency ablation has recently gained favor as a treatment option, although the optimal regime is unknown. This study investigates the effectiveness of 2 versus 3 cycles of radiofrequency ablation for the treatment of Morton's neuroma. We surveyed a cohort of patients with Morton's neuroma who had progressed to radiofrequency ablation after failed conservative treatment. Patients received either 2 or 3 cycles of radiofrequency ablation by a single surgeon. We assessed patients based on their change in numerical pain rating scale, symptom improvement, complications, and progression to surgical excision through a series of telephone interviews. Outcomes between the 2 treatment arms were compared by parametric tests. Twenty-eight patients were included in the study. Eighteen patients with 21 neuromas received 2 cycles and 10 patients with 11 neuromas received 3 cycles. Mean time of follow-up was 12.9 months. Overall, 88% of patients were either very or moderately satisfied with their outcome. In patients who received 2 cycles mean numerical pain scores decreased from 7.9 ± 1.1 to 3.4 ± 2.4 postprocedure. Three patients progressed to operative excision. In patients who received 3 cycles, numerical pain scores decreased from 8.0 ± 1.0 to 1.5 ± 2.0 postprocedure. One patient progressed to operative excision. Patients who received 3 cycles had reduced medium-term pain postoperatively compared with 2 cycles (3.4 ± 2.4 vs 1.5 ± 2.0, P = .011). Radiofrequency ablation provides a high rate of patient satisfaction in the treatment of Morton's neuroma with few side effects. It appears that 3 cycles may be superior to 2 cycles but a randomized controlled trial will be required to confirm these results. Intervention, Level III: Comparative study without concurrent controls.

Production cost comparisons of hydrogen from fossil and nuclear fuel and water decomposition

NASA Technical Reports Server (NTRS)

Ekman, K. R.

1981-01-01

The comparative costs entailed in producing hydrogen by major technologies that rely on petroleum, natural gas, coal, thermochemical cycles, and electrolysis are examined. Techniques were developed for comparing these processes by formulating the process data and economic assessments on a uniform and consistent basis. These data were normalized to permit a meaningful comparative analysis of product costs of these processes.

Life cycle assessment of segregating fattening pig urine and feces compared to conventional liquid manure management.

PubMed

De Vries, Jerke W; Aarnink, André J A; Groot Koerkamp, Peter W G; De Boer, Imke J M

2013-02-05

Gaseous emissions from in-house storage of liquid animal manure remain a major contributor to the environmental impact of manure management. Our aim was to assess the life cycle environmental consequences and reduction potential of segregating fattening pig urine and feces with an innovative V-belt system and to compare it to conventional liquid manure management, that is, the reference. Moreover, we aimed at analyzing the uncertainty of the outcomes related to applied emission factors. We compared a reference with two scenarios: segregation with solid, aerobically, stored feces and with liquid, anaerobically, stored feces. Results showed that, compared to the reference, segregation reduced climate change (CC) up to 82%, due to lower methane emission, reduced terrestrial acidification (TA) and particulate matter formation (PMF) up to 49%, through lower ammonia emission, but increased marine eutrophication up to 11% through nitrogen oxide emission from storage and nitrate leaching after field application. Fossil fuel depletion did not change. Segregation with liquid feces revealed lower environmental impact than segregation with solid feces. Uncertainty analysis supported the conclusion that segregating fattening pig urine and feces significantly reduced CC and additionally segregation with liquid feces significantly reduced TA and PMF compared to the reference.

Protection of muscle membrane excitability during prolonged cycle exercise with glucose supplementation.

PubMed

Stewart, R D; Duhamel, T A; Foley, K P; Ouyang, J; Smith, I C; Green, H J

2007-07-01

To determine if exercise-induced depressions in neuromuscular function are altered with oral glucose supplementation, 15 untrained participants (Vo2 peak = 45 +/- 2 ml x kg(-1) x min(-1), mean +/- SE) performed prolonged cycle exercise at approximately 60% Vo2 peak on two occasions: without glucose supplementation (NG) and with oral glucose supplementation (G). The oral G began at 30 min of exercise and was administered every 15 min (total ingested = 1.23 +/- 0.11 g carbohydrate/kg body mass). Quadriceps isometric properties and membrane excitability were assessed prior to exercise, after 90 min of exercise, and at fatigue. Cycle time to fatigue was greater (P < 0.05) in G compared with NG (137 +/- 7 vs. 115 +/- 6 min). Progressive reductions (P < 0.05) in maximal voluntary contraction (MVC, N) were observed for NG at 90 min (441 +/- 29) and at fatigue (344 +/- 33) compared with pre-exercise (666 +/- 30). At fatigue in G, the reduction in MVC was not as pronounced (P < 0.05) as in NG. Motor unit activation assessed with the interpolated twitch technique during an MVC following exercise was not different between conditions. During cycling, the G condition also resulted in a higher (P < 0.05) muscle compound potential (M-wave) amplitude (mV) at both 90 min (+50%) and at fatigue (+87%) compared with NG. Similar effects were also found M-wave area (mV/ms). These results suggest that the ergogenic effect of glucose supplementation occurs not as a result of decreased neural activation but to improved muscle function, possibly as a consequence of protection of muscle membrane excitability.

Conductive plastics: comparing alternative nanotechnologies by performance and life cycle release probability

NASA Astrophysics Data System (ADS)

Neubauer, Nicole; Wohlleben, Wendel; Tomović, Željko

2017-03-01

Nanocomposites can be considered safe during their life cycle as long as the nanofillers remain embedded in the matrix. Therefore, a possible release of nanofillers has to be assessed before commercialization. This report addresses possible life cycle release scenarios for carbon nanotubes (CNT), graphene, and carbon black (CB) from a thermoplastic polyurethane (TPU) matrix. The content of each nanofiller was adjusted to achieve the same conductivity level. The nanofillers reduced the rate of nanoscale releases during mechanical processing with decreasing release in the order neat TPU, TPU-CNT, TPU-graphene, and TPU-CB. Released fragments were dominated by the polymer matrix with embedded or surface-protruding nanofillers. During electron microscopy analysis, free CB was observed, however, there was no free CNT or graphene. Quantitatively, the presence of free nanofillers remained below the detection limit of <0.01% of generated dust. Further, both the production process and type of mechanical processing showed a significant impact with higher release rates for injection-molded compared to extruded and sanded compared to drilled materials. Due to its optimal performance for further development, extruded TPU-CNT was investigated in a combined, stepwise worst case scenario (mechanical processing after weathering). After weathering by simulated sunlight and rain, CNT were visible at the surface of the nanocomposite; after additional sanding, fragments showed protruding CNT, but free CNT were not detected. In summary, this preliminary exposure assessment showed no indication that recommended occupational exposure limits for carbonaceous nanomaterials can be exceeded during the life cycle of the specific TPU nanocomposites and conditions investigated in this study.

Measuring fecundity with standardised estimates of expected pregnancies.

PubMed

Mikolajczyk, Rafael T; Stanford, Joseph B

2006-11-01

Approaches to measuring fecundity include the assessment of time to pregnancy and day-specific probabilities of conception (daily fecundities) indexed to a day of ovulation. In this paper, we develop an additional approach of calculating expected pregnancies based on daily fecundities indexed to the last day of the menstrual cycle. Expected pregnancies can thus be calculated while controlling for frequency and timing of coitus. Comparing observed pregnancies with expected pregnancies allows for a standardised comparison of fecundity between studies or groups within studies, and can be used to assess the effects of categorical covariates on the woman or couple level, and also on the cycle level. This can be accomplished in a minimal data set that does not necessarily require hormonal measurement or the explicit identification of ovulation. We demonstrate this approach by examining the effects of age and parity on fecundity in a data set from women monitoring their fertility cycles with the Creighton Model FertilityCare System.

An economic evaluation of highly purified HMG and recombinant FSH based on a large randomized trial.

PubMed

Wechowski, Jaroslaw; Connolly, Mark; McEwan, Philip; Kennedy, Richard

2007-11-01

Public funding for IVF is increasingly being challenged by health authorities in an attempt to minimize health service costs. In light of treatment rationing, the need to consider costs in relation to outcomes is paramount. To assess the cost implications of gonadotrophin treatment options, an economic evaluation comparing highly purified human menopausal gonadotrophin (HP-HMG) and recombinant FSH (rFSH) has been conducted. The analysis is based on individual patient data from a large randomized controlled trial (n = 731) in a long agonist IVF protocol. The economic evaluation uses a discrete event simulation model to assess treatment costs in relation to live births for both treatments based on published UK costs. After one cycle the mean costs per IVF treatment for HP-HMG and rFSH were pound2396 (95% CI pound2383-2414) and pound2633 ( pound2615-2652), respectively. The average cost-saving of pound237 per IVF cycle using HP-HMG allows one additional cycle to be delivered for every 10 cycles. With maternal and neonatal costs applied, the median cost per IVF baby delivered with HP-HMG was pound8893 compared with pound11,741 for rFSH (P < 0.001). The cost-saving potential of HP-HMG in IVF was still apparent after varying critical cost parameters in the probabilistic sensitivity analysis.

Sex differences in the risk of rapid cycling and other indicators of adverse illness course in patients with bipolar I and II disorder.

PubMed

Erol, Almila; Winham, Stacey J; McElroy, Susan L; Frye, Mark A; Prieto, Miguel L; Cuellar-Barboza, Alfredo B; Fuentes, Manuel; Geske, Jennifer; Mori, Nicole; Biernacka, Joanna M; Bobo, William V

2015-09-01

To examine the independent effects of sex on the risk of rapid cycling and other indicators of adverse illness course in patients with bipolar I disorder (BP-I) or bipolar II disorder (BP-II). We analyzed data from the first 1,225 patients enrolled in the Mayo Clinic Individualized Medicine Biobank for Bipolar Disorder. Demographic and clinical variables were ascertained using standardized questionnaires; height and weight were assessed to determine body mass index (BMI). Rates of rapid cycling, cycle acceleration, and increased severity of mood episodes over time were compared between women and men overall and within subgroups defined by bipolar disorder subtype (BP-I or BP-II). Multiple logistic regression analysis was used to assess the independent effect of sex on the risk of these indicators of adverse illness course. Women had significantly higher rates of rapid cycling than men. Overall rates of rapid cycling were higher in patients with BP-II than BP-I; and sex differences in the rate of rapid cycling were more pronounced in patients with BP-II than BP-I, although the power to detect statistically significant differences was reduced due to the lower sample size of subjects with BP-II. Female sex was a significant predictor of rapid cycling, cycle acceleration, and increased severity of mood episodes over time after adjusting for age, bipolar disorder subtype, BMI, having any comorbid psychiatric disorder, and current antidepressant use. Female sex was associated with significantly higher risk of rapid cycling, cycle acceleration, and increased severity of mood episodes over time in a sample of 1,225 patients with bipolar disorders. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Physical environmental factors related to walking and cycling in older adults: the Belgian aging studies

PubMed Central

2012-01-01

Background Socio-ecological models emphasize the relationship between the physical environment and physical activity (PA). However, knowledge about this relationship in older adults is limited. Therefore, the present study aims to investigate the relationship between area of residence (urban, semi-urban or rural) and older adults' walking and cycling for transportation and recreation. Additionally, relationships between several physical environmental factors and walking and cycling and possible moderating effects of area of residence, age and gender were studied. Methods Data from 48,879 Flemish older adults collected in 2004-2010 through peer research were analyzed. Walking, cycling and environmental perceptions were assessed using self-administered questionnaires. The Study Service of the Flemish Government provided objective data on municipal characteristics. Multilevel logistic regression analyses were applied. Results Urban participants were more likely to walk daily for transportation compared to rural (OR = 1.43; 95% CI = 1.22, 1.67) and semi-urban participants (OR = 1.32; 95% CI = 1.13, 1.54). Urban participants were less likely to cycle daily for transportation compared to semi-urban participants (OR = 0.72; 95% CI = 0.56, 0.92). Area of residence was unrelated to weekly recreational walking/cycling. Perceived short distances to services (ORs ranging from 1.04 to 1.19) and satisfaction with public transport (ORs ranging from 1.07 to 1.13) were significantly positively related to all walking/cycling behaviors. Feelings of unsafety was negatively related to walking for transportation (OR = 0.93, 95% CI = 0.91, 0.95) and recreational walking/cycling (OR = 0.95, 95% CI = 0.92, 0.97). In females, it was also negatively related to cycling for transportation (OR = 0.94, 95% CI = 0.90, 0.98). Conclusions Urban residents were more likely to walk for transportation daily compared to semi-urban and rural residents. Daily cycling for transportation was less prevalent among urban compared to semi-urban residents. Access to destinations appeared to be important for promoting both walking and cycling for transportation and recreation across all demographic subgroups. Additionaly, feelings of unsafety were associated with lower rates of walking for transportation and walking/cycling for recreation in all subgroups and cycling for transportation in females. No clear patterns emerged for other environmental factors. PMID:22361255

Physical environmental factors related to walking and cycling in older adults: the Belgian aging studies.

PubMed

Van Cauwenberg, Jelle; Clarys, Peter; De Bourdeaudhuij, Ilse; Van Holle, Veerle; Verté, Dominique; De Witte, Nico; De Donder, Liesbeth; Buffel, Tine; Dury, Sarah; Deforche, Benedicte

2012-02-23

Socio-ecological models emphasize the relationship between the physical environment and physical activity (PA). However, knowledge about this relationship in older adults is limited. Therefore, the present study aims to investigate the relationship between area of residence (urban, semi-urban or rural) and older adults' walking and cycling for transportation and recreation. Additionally, relationships between several physical environmental factors and walking and cycling and possible moderating effects of area of residence, age and gender were studied. Data from 48,879 Flemish older adults collected in 2004-2010 through peer research were analyzed. Walking, cycling and environmental perceptions were assessed using self-administered questionnaires. The Study Service of the Flemish Government provided objective data on municipal characteristics. Multilevel logistic regression analyses were applied. Urban participants were more likely to walk daily for transportation compared to rural (OR = 1.43; 95% CI = 1.22, 1.67) and semi-urban participants (OR = 1.32; 95% CI = 1.13, 1.54). Urban participants were less likely to cycle daily for transportation compared to semi-urban participants (OR = 0.72; 95% CI = 0.56, 0.92). Area of residence was unrelated to weekly recreational walking/cycling. Perceived short distances to services (ORs ranging from 1.04 to 1.19) and satisfaction with public transport (ORs ranging from 1.07 to 1.13) were significantly positively related to all walking/cycling behaviors. Feelings of unsafety was negatively related to walking for transportation (OR = 0.93, 95% CI = 0.91, 0.95) and recreational walking/cycling (OR = 0.95, 95% CI = 0.92, 0.97). In females, it was also negatively related to cycling for transportation (OR = 0.94, 95% CI = 0.90, 0.98). Urban residents were more likely to walk for transportation daily compared to semi-urban and rural residents. Daily cycling for transportation was less prevalent among urban compared to semi-urban residents. Access to destinations appeared to be important for promoting both walking and cycling for transportation and recreation across all demographic subgroups. Additionaly, feelings of unsafety were associated with lower rates of walking for transportation and walking/cycling for recreation in all subgroups and cycling for transportation in females. No clear patterns emerged for other environmental factors.

Quality-of-life outcomes from a randomized phase III trial of dose-dense weekly paclitaxel and carboplatin compared with conventional paclitaxel and carboplatin as a first-line treatment for stage II-IV ovarian cancer: Japanese Gynecologic Oncology Group Trial (JGOG3016).

PubMed

Harano, K; Terauchi, F; Katsumata, N; Takahashi, F; Yasuda, M; Takakura, S; Takano, M; Yamamoto, Y; Sugiyama, T

2014-01-01

Dose-dense weekly paclitaxel (Taxol) and carboplatin (dd-TC) improved survival compared with conventional tri-weekly paclitaxel and carboplatin (c-TC) as a first-line chemotherapy for newly diagnosed stage II-IV ovarian cancer in the Japanese Gynecologic Oncology Group 3016 trial. We report the quality-of-life (QoL) results from this trial. A total of 637 patients were randomly assigned to receive c-TC or dd-TC (c-TC, n = 319; dd-TC, n = 312) and were asked to complete a QoL assessment at baseline, just after the third and sixth chemotherapy cycles, and at 12 months after randomization. QoL was assessed using Functional Assessment of Cancer Therapy (FACT)-general (FACT-G), FACT-taxane subscale (FACT-T), and FACT-ovary subscale (FACT-Ov). The overall QoL and that according to each subscale were analyzed using mixed-effects models adjusted for treatment and time. Baseline QoL assessment was completed by 204 out of 319 (63.9%) and 200 out of 312 (64.1%) patients in the c-TC and dd-TC groups, respectively. In these groups, the compliance rates with regard to QoL assessment were 74.5% and 73.0%, respectively, after three chemotherapy cycles; 86.8% and 86.9%, respectively, after six chemotherapy cycles; and 74.2% and 71.6%, respectively, at 12 months after randomization. The overall QoL did not differ significantly between the two treatment groups up to 12 months after randomization (P = 0.46). However, QoL according to the FACT-T subscale was significantly lower in the dd-TC group than in the c-TC group (P = 0.02). dd-TC does not decrease overall QoL compared with c-TC.

Engine system assessment study using Martian propellants

NASA Technical Reports Server (NTRS)

Pelaccio, Dennis; Jacobs, Mark; Scheil, Christine; Collins, John

1992-01-01

A top-level feasibility study was conducted that identified and characterized promising chemical propulsion system designs which use two or more of the following propellant combinations: LOX/H2, LOX/CH4, and LOX/CO. The engine systems examined emphasized the usage of common subsystem/component hardware where possible. In support of this study, numerous mission scenarios were characterized that used various combinations of Earth, lunar, and Mars propellants to establish engine system requirements to assess the promising engine system design concept examined, and to determine overall exploration leverage of such systems compared to state-of-the-art cryogenic (LOX/H2) propulsion systems. Initially in the study, critical propulsion system technologies were assessed. Candidate expander and gas generator cycle LOX/H2/CO, LOX/H2/CH4, and LOX/CO/CH4 engine system designs were parametrically evaluated. From this evaluation baseline, tripropellant Mars Transfer Vehicle (MTV) LOX cooled and bipropellant Lunar Excursion Vehicle (LEV) and Mars Excursion Vehicle (MEV) engine systems were identified. Representative tankage designs for a MTV were also investigated. Re-evaluation of the missions using the baseline engine design showed that in general the slightly lower performance, smaller, lower weight gas generator cycle-based engines required less overall mission Mars and in situ propellant production (ISPP) infrastructure support compared to the larger, heavier, higher performing expander cycle engine systems.

Environmental impact analysis of batik natural dyes using life cycle assessment

NASA Astrophysics Data System (ADS)

Rinawati, Dyah Ika; Sari, Diana Puspita; Purwanggono, Bambang; Hermawan, Andy Tri

2017-11-01

The use of natural dyes for batik dyeing is fewer than synthetic dyes because of its limitations in the application such complexity in manufacture and usage. For ease of use, natural dyes need to be processed into instant products. Extract of natural dyes are generally produced in liquid form that are less practical in long-term use. Dye powder obtained by drying the liquid extract using spray dryer. Production process of liquid natural dye is simpler and require less energy but need more energy for transporting. It is important to know which type of natural dyes should be produced based on their environmental impact. This research aim to compare environmental impact between liquid and powder natural dyes and also to find relative contribution of different stage in life cycle to total environmental impact. The appropriate method to analyze and compare the environmental impacts of powder and liquid natural dyes is Life Cycle Assessment (LCA). The "cradle to grave" approach used to assess environmental impact of powder and liquid natural dyes of Jalawe rind throughout production process of natural dyes, distribution and use of natural dyes for coloring batik. Results of this research show that powder natural dyes has lower environmental impacts than liquid natural dyes. It was found that distribution, mordanting and packaging of liquid dyes have big contribution to environmental impact.

Adrenal hyperandrogenism is induced by fetal androgen excess in a rhesus monkey model of polycystic ovary syndrome.

PubMed

Zhou, Rao; Bird, Ian M; Dumesic, Daniel A; Abbott, David H

2005-12-01

Adrenal androgen excess is found in approximately 25-60% of women with polycystic ovary syndrome (PCOS), but the mechanisms underlying PCOS-related adrenal androgen excess are unclear. The objective of this study was to determine whether adrenal androgen excess is manifest in a nonhuman primate model for PCOS. Six prenatally androgenized (PA) and six control female rhesus monkeys of similar age, body weight, and body mass index were studied during d 2-6 of two menstrual cycles or anovulatory 30-d periods. Predexamethasone adrenal steroid levels were assessed in the first cycle (cycle 1). In a subsequent cycle (cycle 2), occurring one to three cycles after cycle 1, adrenal steroids were determined 14.5-16.0 h after an i.m. injection of 0.5 mg/kg dexamethasone (postdexamethasone levels) and after an i.v. injection of 50 microg ACTH-(1-39). Both before and after dexamethasone, serum levels of dehydroepiandrosterone (DHEA) in PA females exceeded those in controls. After ACTH injection, PA females exhibited higher circulating levels of DHEA, androstenedione, and corticosterone but comparable levels of 17alpha-hydroxyprogesterone, cortisol, the sulfoconjugate of DHEA, and testosterone compared with controls. Enhanced basal and ACTH-stimulated adrenal androgen levels in PA female monkeys may reflect up-regulation of 17,20 lyase activity in the adrenal zona reticularis, causing adrenal androgen excess comparable with that found in PCOS women with adrenal androgen excess. These findings open the possibility that PCOS adrenal hyperandrogenism may have its origins in fetal androgen excess reprogramming of adrenocortical function.

Acute effect of cycling intervention on carotid arterial hemodynamics: basketball athletes versus sedentary controls

PubMed Central

2015-01-01

Objective To compare the acute effects of a cycling intervention on carotid arterial hemodynamics between basketball athletes and sedentary controls. Methods Ten young long-term trained male basketball athletes (BA) and nine age-matched male sedentary controls (SC) successively underwent four bouts of exercise on a bicycle ergometer at the same workload. Hemodynamic variables at right common carotid artery were determined at rest and immediately following each bout of exercise. An ANCOVA was used to compare differences between the BA and SC groups at rest and immediately following the cycling intervention. The repeated ANOVA was used to assess differences between baseline and each bout of exercise within the BA or SC group. Results In both groups, carotid hemodynamic variables showed significant differences at rest and immediately after the cycling intervention. At rest, carotid arterial stiffness was significantly decreased and carotid arterial diameter was significantly increased in the BA group as compared to the SC group. Immediately following the cycling intervention, carotid arterial stiffness showed no obvious changes in the BA group but significantly increased in the SC group. It is worth noting that while arterial stiffness was lower in the BA group than in the SC group, the oscillatory shear index (OSI) was significantly higher in the BA group than in the SC group both at rest and immediately following the cycling intervention. Conclusion Long-term basketball exercise had a significant impact on common carotid arterial hemodynamic variables not only at rest but also after a cycling intervention. The role of OSI in the remodeling of arterial structure and function in the BA group at rest and after cycling requires clarification. PMID:25602805

Environmental and economic assessment of a road safety product made with virgin and recycled HDPE: a comparative study.

PubMed

L Simões, Carla; Costa Pinto, Lígia M; Bernardo, C A

2013-01-15

The development of value-added products made from post-consumer plastic recyclates has become an important goal in the quest for a sustainable society. To attain such goal, tools with higher accuracy and wider scope are increasingly necessary. The present work describes the application of a Life Cycle Assessment (LCA)/Life Cycle Costing (LCC) integrated model, with inclusion of externalities (environmental and social costs), to Anti-Glare Lamellae (AGL) made with High Density Polyethylene (HDPE). It compares an AGL currently manufactured from virgin HDPE (current AGL) with an alternative one made with recycled HDPE (optional AGL). The results obtained show that neither the current nor the optional AGL depict the best environmental performance in all impact categories. Nevertheless, there is a clear overall environmental and economic advantage in replacing virgin HDPE with recycled HDPE. The present work also makes evident that the LCA/LCC integrated model allows the identification of economic and environmental win-win and trade-off situations related to the full life cycle of products. As such, its results can be used as valuable guidelines in product development. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

PubMed

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Neuromuscular Fatigue during Prolonged Exercise in Hypoxia.

PubMed

Jubeau, Marc; Rupp, Thomas; Temesi, John; Perrey, Stéphane; Wuyam, Bernard; Millet, Guillaume Y; Verges, Samuel

2017-03-01

Prolonged cycling exercise performance in normoxia is limited because of both peripheral and central neuromuscular impairments. It has been reported that cerebral perturbations are greater during short-duration exercise in hypoxia compared with normoxia. The purpose of this study was to test the hypothesis that central deficits are accentuated in hypoxia compared with normoxia during prolonged (three bouts of 80 min separated by 25 min) whole-body exercise at the same relative intensity. Ten subjects performed two sessions consisting of three 80-min cycling bouts at 45% of their relative maximal aerobic power in normoxia and hypoxia (FiO2 = 0.12). Before exercise and after each bout, maximal voluntary force, voluntary activation assessed with nerve stimulation and transcranial magnetic stimulation, corticospinal excitability (motor evoked potential), intracortical inhibition (cortical silent period), and electrical (M-wave) and contractile (twitch and doublet peak forces) properties of the knee extensors were measured. Prefrontal and motor cortical oxygenation was also recorded during each cycling bout in both conditions. A significant but similar force reduction (≈-22%) was observed at the end of exercise in normoxia and hypoxia. The modifications of voluntary activation assessed with transcranial magnetic stimulation and nerve stimulation, motor evoked potential, cortical silent period, and M-wave were also similar in both conditions. However, cerebral oxygenation was reduced in hypoxia compared with normoxia. These findings show that when performed at the same relative low intensity, prolonged exercise does not induce greater supraspinal fatigue in hypoxia compared with normoxia. Despite lower absolute exercise intensities in hypoxia, reduced brain O2 availability might contribute to similar amounts of central fatigue compared with normoxia.

Cardiorespiratory Kinetics Determined by Pseudo-Random Binary Sequences - Comparisons between Walking and Cycling.

PubMed

Koschate, J; Drescher, U; Thieschäfer, L; Heine, O; Baum, K; Hoffmann, U

2016-12-01

This study aims to compare cardiorespiratory kinetics as a response to a standardised work rate protocol with pseudo-random binary sequences between cycling and walking in young healthy subjects. Muscular and pulmonary oxygen uptake (V̇O 2 ) kinetics as well as heart rate kinetics were expected to be similar for walking and cycling. Cardiac data and V̇O 2 of 23 healthy young subjects were measured in response to pseudo-random binary sequences. Kinetics were assessed applying time series analysis. Higher maxima of cross-correlation functions between work rate and the respective parameter indicate faster kinetics responses. Muscular V̇O 2 kinetics were estimated from heart rate and pulmonary V̇O 2 using a circulatory model. Muscular (walking vs. cycling [mean±SD in arbitrary units]: 0.40±0.08 vs. 0.41±0.08) and pulmonary V̇O 2 kinetics (0.35±0.06 vs. 0.35±0.06) were not different, although the time courses of the cross-correlation functions of pulmonary V̇O 2 showed unexpected biphasic responses. Heart rate kinetics (0.50±0.14 vs. 0.40±0.14; P=0.017) was faster for walking. Regarding the biphasic cross-correlation functions of pulmonary V̇O 2 during walking, the assessment of muscular V̇O 2 kinetics via pseudo-random binary sequences requires a circulatory model to account for cardio-dynamic distortions. Faster heart rate kinetics for walking should be considered by comparing results from cycle and treadmill ergometry. © Georg Thieme Verlag KG Stuttgart · New York.

Mitigation measures to contain the environmental impact of urban areas: a bibliographic review moving from the life cycle approach.

PubMed

Belussi, Lorenzo; Barozzi, Benedetta

2015-12-01

The global environmental impact of urban areas has greatly increased over the years, due to the growth of urbanisation and the associated increase in management costs. There are several measures aimed at mitigating this impact that affect in different ways the environmental, economic and societal spheres. This article has analysed a selection of different mitigation measures, related to the built environment, according to the life cycle approach, aimed at identifying the procedural features chosen by the different authors and defining a common way to deal with this issue. In particular, all the individual single steps of a Life Cycle Assessment/Life Cycle Costing of the different studies are analysed and the results of the individual measures are highlighted. The analysis has shown how the scientific literature is mainly focused on the evaluation of the impact of technological solutions related to individual buildings (cool/green roof). Less interest is shown in the solutions for urban areas, while, as far as the impact on greenhouse gas emissions is concerned, some studies are shifting the target to a global scale. Due to the accuracy whereby the calculation of the impact indicators deals with and structures the life cycle methods, opportunities to compare studies developed by different authors are quite rare and hard to find. Hence the need to find a simple, intuitive and flexible scheme to combine some of the most useful results of the bibliographical studies, in a comparative outline of different technological solutions, which can support the decision-making phase through a rough assessment.

Results of the third reproductive assessment survey of North American Asian (Elephas maximus) and African (Loxodonta africana) female elephants.

PubMed

Dow, T L; Holásková, I; Brown, J L

2011-01-01

A written survey assessed reproductive status of female Asian and African elephants in AZA/SSP facilities in 2008, and data were compared to surveys conducted in 2002 and 2005. Results showed that ovarian acyclicity rates across the surveys remained unchanged for Asian (13.3, 10.9 and 11.1%) and African (22.1, 31.2 and 30.5%) elephants, respectively (P > 0.05), but were higher overall for African compared to Asian elephants (P < 0.05). In 2008, the percentages of Asian and African elephants with irregular cycles (14.3 and 15.8%) and irregular + no cycles (25.4 and 46.4%) was similar to 2005 (7.6 and 11.8%; 18.5 and 43.0%), but were increased compared to 2002 (2.6 and 5.2%; 16.0 and 27.3%), respectively (P < 0.05). For both species, ovarian acyclicity increased with age (P < 0.05). Reproductive tract pathologies did not account for the majority of acyclicity, although rates were higher in noncycling females (P < 0.05). Bull presence was associated with increased cyclicity rates (P < 0.05) for Asian (92.5 vs. 58.3%) and African (64.9 vs. 57.8%) elephants compared to females at facilities with no male, respectively. Cyclicity rates were higher for Asian (86.8 vs. 65.2%) and African (67.9 vs. 56.7%) elephants managed in free compared to protected contact programs (P < 0.05), respectively. Geographical facility location had no effect on cyclicity (P > 0.05). In summary, incidence of ovarian cycle problems continues to predominantly affect African elephants. Although percentages of acyclicity did not increase between 2005 and 2008, 42.2% Asian and 30.2% African females were no longer being hormonally monitored; thus, reproductive cycle abnormalities could be worse than current data suggest. © 2011 Wiley Periodicals, Inc.

Comparative life cycle assessment of disposable and reusable laryngeal mask airways.

PubMed

Eckelman, Matthew; Mosher, Margo; Gonzalez, Andres; Sherman, Jodi

2012-05-01

Growing awareness of the negative impacts from the practice of health care on the environment and public health calls for the routine inclusion of life cycle criteria into the decision-making process of device selection. Here we present a life cycle assessment of 2 laryngeal mask airways (LMAs), a one-time-use disposable Unique™ LMA and a 40-time-use reusable Classic™ LMA. In life cycle assessment, the basis of comparison is called the "functional unit." For this report, the functional unit of the disposable and reusable LMAs was taken to be maintenance of airway patency by 40 disposable LMAs or 40 uses of 1 reusable LMA. This was a cradle-to-grave study that included inputs and outputs for the manufacture, transport, use, and waste phases of the LMAs. The environmental impacts of the 2 LMAs were estimated using SimaPro life cycle assessment software and the Building for Environmental and Economic Sustainability impact assessment method. Sensitivity and simple life cycle cost analyses were conducted to aid in interpretation of the results. The reusable LMA was found to have a more favorable environmental profile than the disposable LMA as used at Yale New Haven Hospital. The most important sources of impacts for the disposable LMA were the production of polymers, packaging, and waste management, whereas for the reusable LMA, washing and sterilization dominated for most impact categories. The differences in environmental impacts between these devices strongly favor reusable devices. These benefits must be weighed against concerns regarding transmission of infection. Health care facilities can decrease their environmental impacts by using reusable LMAs, to a lesser extent by selecting disposable LMA models that are not made of certain plastics, and by ordering in bulk from local distributors. Certain practices would further reduce the environmental impacts of reusable LMAs, such as increasing the number of devices autoclaved in a single cycle to 10 (-25% GHG emissions) and improving the energy efficiency of the autoclaving machines by 10% (-8% GHG emissions). For both environmental and cost considerations, management and operating procedures should be put in place to ensure that reusable LMAs are not discarded prematurely.

A Comparative Analysis of Pre-Equating and Post-Equating in a Large-Scale Assessment, High Stakes Examination

ERIC Educational Resources Information Center

Ojerinde, Dibu; Popoola, Omokunmi; Onyeneho, Patrick; Egberongbe, Aminat

2016-01-01

Statistical procedure used in adjusting test score difficulties on test forms is known as "equating". Equating makes it possible for various test forms to be used interchangeably. In terms of where the equating method fits in the assessment cycle, there are pre-equating and post-equating methods. The major benefits of pre-equating, when…

[Comparative life cycle environmental assessment between electric taxi and gasoline taxi in Beijing].

PubMed

Shi, Xiao-Qing; Sun, Zhao-Xin; Li, Xiao-Nuo; Li, Jin-Xiang; Yang, Jian-Xin

2015-03-01

Tailpipe emission of internal combustion engine vehicle (ICEV) is one of the main sources leading to atmospheric environmental problems such as haze. Substituting electric vehicles for conventional gasoline vehicles is an important solution for reducing urban air pollution. In 2011, as a pilot city of electric vehicle, Beijing launched a promotion plan of electric vehicle. In order to compare the environmental impacts between Midi electric vehicle (Midi EV) and Hyundai gasoline taxi (ICEV), this study created an inventory with local data and well-reasoned assumptions, and contributed a life cycle assessment (LCA) model with GaBi4.4 software and comparative life cycle environmental assessment by Life cycle impact analysis models of CML2001(Problem oriented) and EI99 (Damage oriented), which included the environmental impacts of full life cycle, manufacture phase, use phase and end of life. The sensitivity analysis of lifetime mileage and power structure was also provided. The results indicated that the full life cycle environmental impact of Midi EV was smaller than Hyundai ICEV, which was mainly due to the lower fossil fuel consumption. On the contrary, Midi EV exhibited the potential of increasing the environmental impacts of ecosystem quality influence and Human health influence. By CML2001 model, the results indicated that Midi EV might decrease the impact of Abiotic Depletion Potential, Global Warming Potential, Ozone Layer Depletion Potential and so on. However, in the production phase, the impact of Abiotic Depletion Potential, Acidification Potential, Eutrophication Potential, Global Warming Potential, Photochemical Ozone Creation Potential, Ozone Layer Depletion Potential, Marine Aquatic Ecotoxicity Potential, Terrestric Ecotoxicity Potential, Human Toxicity Potential of Midi EV were increased relative to Hyundai ICEV because of emissions impacts from its power system especially the battery production. Besides, in the use phase, electricity production was the main process leading to the impact of Abiotic Depletion Potential, Acidification Potential, Eutrophication Potential, Global Warming Potential, Photochemical Ozone Creation Potential, Marine Aquatic Ecotoxicity Potential, Freshwater Aquatic Ecotoxicity Potential, Human Toxicity Potential. While for Hyundai ICEV, gasoline production and tailpipe emission were the primary sources of environmental impact in the use phase. Tailpipe emission was a significant cause for increase in Eutrophication Potential and Global Warming Potential, and so forth. On the basis of inventory data analysis and 2010 Beijing electricity mix, the comparative results of haze-induced pollutants emissions showed that the full life cycle emissions of PM2.5, NO(x), SO(x), VOCs of Midi EV were higher than those of Hyundai ICEV, but the emission of NH3 was lower than that of Hyundai ICEV. Different emissions in use phase were the chief reason leading to this trend. In addition, by sensitivity analysis the results indicated that with the increase of lifetime mileage and proportion of cleaning energy, the rate of GHG( Green House Gas) emission reduction per kilometer of Midi EV became higher with respect to Hyundai ICEV. Haze-induced pollutants emission from EV could be significantly reduced using cleaner power energy. According to the assessment results, some management strategies aiming at electric car promotion were proposed.

Life Cycle Assessment of Wall Systems

NASA Astrophysics Data System (ADS)

Ramachandran, Sriranjani

Natural resource depletion and environmental degradation are the stark realities of the times we live in. As awareness about these issues increases globally, industries and businesses are becoming interested in understanding and minimizing the ecological footprints of their activities. Evaluating the environmental impacts of products and processes has become a key issue, and the first step towards addressing and eventually curbing climate change. Additionally, companies are finding it beneficial and are interested in going beyond compliance using pollution prevention strategies and environmental management systems to improve their environmental performance. Life-cycle Assessment (LCA) is an evaluative method to assess the environmental impacts associated with a products' life-cycle from cradle-to-grave (i.e. from raw material extraction through to material processing, manufacturing, distribution, use, repair and maintenance, and finally, disposal or recycling). This study focuses on evaluating building envelopes on the basis of their life-cycle analysis. In order to facilitate this analysis, a small-scale office building, the University Services Building (USB), with a built-up area of 148,101 ft2 situated on ASU campus in Tempe, Arizona was studied. The building's exterior envelope is the highlight of this study. The current exterior envelope is made of tilt-up concrete construction, a type of construction in which the concrete elements are constructed horizontally and tilted up, after they are cured, using cranes and are braced until other structural elements are secured. This building envelope is compared to five other building envelope systems (i.e. concrete block, insulated concrete form, cast-in-place concrete, steel studs and curtain wall constructions) evaluating them on the basis of least environmental impact. The research methodology involved developing energy models, simulating them and generating changes in energy consumption due to the above mentioned envelope types. Energy consumption data, along with various other details, such as building floor area, areas of walls, columns, beams etc. and their material types were imported into Life-Cycle Assessment software called ATHENA impact estimator for buildings. Using this four-stepped LCA methodology, the results showed that the Steel Stud envelope performed the best and less environmental impact compared to other envelope types. This research methodology can be applied to other building typologies.

A cycling workstation to facilitate physical activity in office settings.

PubMed

Elmer, Steven J; Martin, James C

2014-07-01

Facilitating physical activity during the workday may help desk-bound workers reduce risks associated with sedentary behavior. We 1) evaluated the efficacy of a cycling workstation to increase energy expenditure while performing a typing task and 2) fabricated a power measurement system to determine the accuracy and reliability of an exercise cycle. Ten individuals performed 10 min trials of sitting while typing (SIT type) and pedaling while typing (PED type). Expired gases were recorded and typing performance was assessed. Metabolic cost during PED type was ∼ 2.5 × greater compared to SIT type (255 ± 14 vs. 100 ± 11 kcal h(-1), P < 0.01). Typing time and number of typing errors did not differ between PED type and SIT type (7.7 ± 1.5 vs. 7.6 ± 1.6 min, P = 0.51, 3.3 ± 4.6 vs. 3.8 ± 2.7 errors, P = 0.80). The exercise cycle overestimated power by 14-138% compared to actual power but actual power was reliable (r = 0.998, P < 0.01). A cycling workstation can facilitate physical activity without compromising typing performance. The exercise cycle's inaccuracy could be misleading to users. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The role of menstrual cycle phase and anxiety sensitivity in catastrophic misinterpretation of physical symptoms during a CO(2) challenge.

PubMed

Nillni, Yael I; Rohan, Kelly J; Zvolensky, Michael J

2012-12-01

The current study examined the interactive effects of anxiety sensitivity (AS; fear of anxiety and anxiety-related sensations) and menstrual cycle phase (premenstrual phase vs. follicular phase) on panic-relevant responding (i.e., cognitive and physical panic symptoms, subjective anxiety, and skin conductance level). Women completed a baseline session and underwent a 3-min 10 % CO(2)-enriched air biological challenge paradigm during her premenstrual and follicular menstrual cycle phases. Participants were 55 women with no current or past history of panic disorder recruited from the general community (M (age) = 26.18, SD = 8.9) who completed the biological challenge during both the premenstrual and follicular cycle phases. Results revealed that women higher on AS demonstrated increased cognitive panic symptoms in response to the challenge during the premenstrual phase as compared to the follicular phase, and as compared to women lower on AS assessed in either cycle phase. However, the interaction of AS and menstrual cycle phase did not significantly predict physical panic attack symptoms, subjective ratings of anxiety, or skin conductance level in response to the challenge. Results are discussed in the context of premenstrual exacerbations of cognitive, as opposed to physical, panic attack symptoms for high AS women, and the clinical implications of these findings.

Luteal Phase Support in the Intrauterine Insemination (IUI) Cycles: A Randomized Double Blind, Placebo Controlled Study

PubMed Central

Hossein Rashidi, Batool; Davari Tanha, Fatemeh; Rahmanpour, Haleh; Ghazizadeh, Mahya

2014-01-01

Objective: To evaluate the impact of luteal phase support with vaginal progesterone on pregnancy rates in the intrauterine insemination (IUI) cycles, stimulated with clomiphene citrate and human menopausal gonadotropin (hMG), in sub fertile couples. Materials and methods: This prospective, randomized, double blind study was performed in a tertiary infertility center from March 2011 to January 2012. It consisted of 253 sub fertile couples undergoing ovarian stimulation for IUI cycles. They underwent ovarian stimulation with clomiphene citrate (100 mg) and hMG (75 IU) in preparation for the IUI cycle. Study group (n = 127) received luteal phase support in the form of vaginal progesterone (400 mg twice a day), and control group (n = 126) received placebo. Clinical pregnancy and abortion rates were assessed and compared between the two groups. Results: The clinical pregnancy rate was not significantly higher for supported cycles than that for the unsupported ones (15.75% vs. 12.69%, p = 0.3). The abortion rate in the patients with progesterone luteal support compared to placebo group was not statistically different (10% vs. 18.75%, p = 0.45). Conclusion: It seems that luteal phase support with vaginal progesterone was not enhanced the success of IUI cycles outcomes, when clomiphene citrate and hMG were used for ovulation stimulation. PMID:25530766

Relation between Peak Power Output in Sprint Cycling and Maximum Voluntary Isometric Torque Production.

PubMed

Kordi, Mehdi; Goodall, Stuart; Barratt, Paul; Rowley, Nicola; Leeder, Jonathan; Howatson, Glyn

2017-08-01

From a cycling paradigm, little has been done to understand the relationships between maximal isometric strength of different single joint lower body muscle groups and their relation with, and ability to predict PPO and how they compare to an isometric cycling specific task. The aim of this study was to establish relationships between maximal voluntary torque production from isometric single-joint and cycling specific tasks and assess their ability to predict PPO. Twenty male trained cyclists participated in this study. Peak torque was measured by performing maximum voluntary contractions (MVC) of knee extensors, knee flexors, dorsi flexors and hip extensors whilst instrumented cranks measured isometric peak torque from MVC when participants were in their cycling specific position (ISOCYC). A stepwise regression showed that peak torque of the knee extensors was the only significant predictor of PPO when using SJD and accounted for 47% of the variance. However, when compared to ISOCYC, the only significant predictor of PPO was ISOCYC, which accounted for 77% of the variance. This suggests that peak torque of the knee extensors was the best single-joint predictor of PPO in sprint cycling. Furthermore, a stronger prediction can be made from a task specific isometric task. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental assessment of different dewatering and drying methods on the basis of life cycle assessment.

PubMed

Stefaniak, J; Zelazna, A; Pawłowski, A

2014-01-01

Sewage sludge is an inevitable product of wastewater treatment in municipal wastewater plants and its amount has increased dramatically due to the growing number of sewage systems users. This sludge needs to be adequately treated in order to decrease its hazardous properties and any negative influence on the environment. In this paper, gate to gate analysis, on the basis of life cycle assessment (LCA), was carried out in order to compare the environmental impact of alternative ways of sludge processing employing a dewatering press and three different kinds of dryers - belt dryer, container dryer and batch dryer. SimaPro 7.2 software and Ecoinvent 2.2 database were used to estimate the carbon footprint and energy balance of these processes. The main energy consumption in the scenarios analyzed is caused by the drying process. The solution based on application of the batch dryer allows a saving of 39.6% of energy compared with the most energy-consuming solution using a belt dryer. Sludge processing using belt and container dryers cause greater environmental burdens.

A Life Cycle Assessment (LCA) comparison of three management options for waste papers: bioethanol production, recycling and incineration with energy recovery.

PubMed

Wang, Lei; Templer, Richard; Murphy, Richard J

2012-09-01

This study uses Life Cycle Assessment (LCA) to assess the environmental profiles and greenhouse gas (GHG) emissions for bioethanol production from waste papers and to compare them with the alternative waste management options of recycling or incineration with energy recovery. Bioethanol production scenarios both with and without pre-treatments were conducted. It was found that an oxidative lime pre-treatment reduced GHG emissions and overall environmental burdens for a newspaper-to-bioethanol process whereas a dilute acid pre-treatment raised GHG emissions and overall environmental impacts for an office paper-to-bioethanol process. In the comparison of bioethanol production systems with alternative management of waste papers by different technologies, it was found that the environmental profiles of each system vary significantly and this variation affects the outcomes of the specific comparisons made. Overall, a number of configurations of bioethanol production from waste papers offer environmentally favourable or neutral profiles when compared with recycling or incineration. Copyright © 2012 Elsevier Ltd. All rights reserved.

Life cycle assessment of microalgae-based aviation fuel: Influence of lipid content with specific productivity and nitrogen nutrient effects.

PubMed

Guo, Fang; Zhao, Jing; A, Lusi; Yang, Xiaoyi

2016-12-01

The aim of this work is to compare the life cycle assessments of low-N and normal culture conditions for a balance between the lipid content and specific productivity. In order to achieve the potential contribution of lipid content to the life cycle assessment, this study established relationships between lipid content (nitrogen effect) and specific productivity based on three microalgae strains including Chlorella, Isochrysis and Nannochloropsis. For microalgae-based aviation fuel, the effects of the lipid content on fossil fuel consumption and greenhouse gas (GHG) emissions are similar. The fossil fuel consumption (0.32-0.68MJ·MJ -1 MBAF) and GHG emissions (17.23-51.04gCO 2 e·MJ -1 MBAF) increase (59.70-192.22%) with the increased lipid content. The total energy input decreases (2.13-3.08MJ·MJ -1 MBAF, 14.91-27.95%) with the increased lipid content. The LCA indicators increased (0-47.10%) with the decreased nitrogen recovery efficiency (75-50%). Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing the use of assisted reproductive technology in the United States by non-United States residents.

PubMed

Levine, Aaron D; Boulet, Sheree L; Berry, Roberta M; Jamieson, Denise J; Alberta-Sherer, Hillary B; Kissin, Dmitry M

2017-11-01

To study cross-border reproductive care (CBRC) by assessing the frequency and nature of assisted reproductive technology (ART) care that non-U.S. residents receive in the United States. Retrospective study of ART cycles reported to the Centers for Disease Control and Prevention's National ART Surveillance System (NASS) from 2006 to 2013. Private and academic ART clinics. Patients who participated in ART cycles in the United States from 2006 to 2013. None. Frequency and trend of ART use in the U.S. by non-U.S. residents, countries of residence for non-U.S. residents, differences by residence status for specific ART treatments received, and the outcomes of these ART cycles. A total of 1,271,775 ART cycles were reported to NASS from 2006 to 2013. The percentage of ART cycles performed for non-U.S. residents increased from 1.2% (n = 1,683) in 2006 to 2.8% (n = 5,381) in 2013 (P<.001), with treatment delivered to residents of 147 countries. Compared with resident cycles, non-U.S. resident cycles had higher use of oocyte donation (10.6% vs. 42.6%), gestational carriers (1.6% vs. 12.4%), and preimplantation genetic diagnosis or screening (5.3% vs. 19.1%). U.S. resident and non-U.S. resident cycles had similar embryo transfer and multiple birth rates. This analysis showed that non-U.S. resident cycles accounted for a growing share of all U.S. ART cycles and made higher use of specialized treatment techniques. This study provides important baseline data on CBRC in the U.S. and may also prove to be useful to organizations interested in improving access to fertility treatments. Copyright © 2017 American Society for Reproductive Medicine. All rights reserved.

Characterization of alternative electric generation technologies for the SPS comparative assessment. Volume 1: Summary of central station technologies

NASA Astrophysics Data System (ADS)

1980-08-01

The technologies selected for the detailed characterization were: solar technology; terrestrial photovoltaic (200 MWe); coal technologies; conventional high sulfur coal combustion with advanced fine gas desulfurization (1250 MWe), and open cycle gas turbine combined cycle plant with low Btu gasifier (1250 MWe); and nuclear technologies: conventional light water reactor (1250 MWe), liquid metal fast breeder reactor (1250 MWe), and magnetic fusion reactor (1320 MWe). A brief technical summary of each power plant design is given.

Preliminary comparative assessment of land use for the Satellite Power System (SPS) and alternative electric energy technologies

NASA Technical Reports Server (NTRS)

Newsom, D. E.; Wolsko, T.

1980-01-01

A preliminary comparative assessment of land use for the satellite power system (SPS), other solar technologies, and alternative electric energy technologies was conducted. The alternative technologies are coal gasification/combined-cycle, coal fluidized-bed combustion (FBC), light water reactor (LWR), liquid metal fast breeder reactor (LMFBR), terrestrial photovoltaics (TPV), solar thermal electric (STE), and ocean thermal energy conversion (OTEC). The major issues of a land use assessment are the quantity, purpose, duration, location, and costs of the required land use. The phased methodology described treats the first four issues, but not the costs. Several past efforts are comparative or single technology assessment are reviewed briefly. The current state of knowledge about land use is described for each technology. Conclusions are drawn regarding deficiencies in the data on comparative land use and needs for further research.

Quantifying the benefits of the Florida Transit Research Inspection Procurement Services (TRIPS) program.

DOT National Transportation Integrated Search

2013-04-01

This study details the analysis of the Florida Transit Research Inspection Procurement Services (TRIPS) Program. It provides a comparative assessment of the program with respect to out-of-state practice, provides recommendations to improve life cycle...

Validation of different instruments for caffeine measurement among premenopausal women in the BioCycle study.

PubMed

Schliep, Karen C; Schisterman, Enrique F; Mumford, Sunni L; Perkins, Neil J; Ye, Aijun; Pollack, Anna Z; Zhang, Cuilin; Porucznik, Christina A; VanDerslice, James A; Stanford, Joseph B; Wactawski-Wende, Jean

2013-04-01

Effects of caffeine on women's health are inconclusive, in part because of inadequate exposure assessment. In this study we determined 1) validity of a food frequency questionnaire compared with multiple 24-hour dietary recalls (24HDRs) for measuring monthly caffeine and caffeinated beverage intakes; and 2) validity of the 24HDR compared with the prior day's diary record for measuring daily caffeinated coffee intake. BioCycle Study (2005-2007) participants, women (n = 259) aged 18-44 years from western New York State, were followed for 2 menstrual cycles. Participants completed a food frequency questionnaire at the end of each cycle, four 24HDRs per cycle, and daily diaries. Caffeine intakes reported for the food frequency questionnaires were greater than those reported for the 24HDRs (mean = 114.1 vs. 92.6mg/day, P = 0.01) but showed high correlation (r = 0.73, P < 0.001) and moderate agreement (К = 0.51, 95% confidence interval: 0.43, 0.57). Women reported less caffeinated coffee intake in their 24HDRs compared with their corresponding diary days (mean = 0.51 vs. 0.80 cups/day, P < 0.001) (1 cup = 237 mL). Although caffeine and coffee exposures were highly correlated, absolute intakes differed significantly between measurement tools. These results highlight the importance of considering potential misclassification of caffeine exposure.

Validation of Different Instruments for Caffeine Measurement Among Premenopausal Women in the BioCycle Study

PubMed Central

Schliep, Karen C.; Schisterman, Enrique F.; Mumford, Sunni L.; Perkins, Neil J.; Ye, Aijun; Pollack, Anna Z.; Zhang, Cuilin; Porucznik, Christina A.; VanDerslice, James A.; Stanford, Joseph B.; Wactawski-Wende, Jean

2013-01-01

Effects of caffeine on women's health are inconclusive, in part because of inadequate exposure assessment. In this study we determined 1) validity of a food frequency questionnaire compared with multiple 24-hour dietary recalls (24HDRs) for measuring monthly caffeine and caffeinated beverage intakes; and 2) validity of the 24HDR compared with the prior day's diary record for measuring daily caffeinated coffee intake. BioCycle Study (2005–2007) participants, women (n = 259) aged 18–44 years from western New York State, were followed for 2 menstrual cycles. Participants completed a food frequency questionnaire at the end of each cycle, four 24HDRs per cycle, and daily diaries. Caffeine intakes reported for the food frequency questionnaires were greater than those reported for the 24HDRs (mean = 114.1 vs. 92.6mg/day, P = 0.01) but showed high correlation (r = 0.73, P < 0.001) and moderate agreement (К = 0.51, 95% confidence interval: 0.43, 0.57). Women reported less caffeinated coffee intake in their 24HDRs compared with their corresponding diary days (mean = 0.51 vs. 0.80 cups/day, P < 0.001) (1 cup = 237 mL). Although caffeine and coffee exposures were highly correlated, absolute intakes differed significantly between measurement tools. These results highlight the importance of considering potential misclassification of caffeine exposure. PMID:23462965

Comparing the Effect of Auriculotherapy and Vitamin B6 on the Symptoms of Premenstrual Syndrome among the Students who Lived in the Dorm of Isfahan University of Medical Sciences.

PubMed

Koleini, Sharareh; Valiani, Mahboubeh

2017-01-01

Premenstrual syndrome (PMS) is a series of physical and psychological symptoms before menstruation which its prevalence around the world has been reported to be 80%. Consumption of vitamin B6 is a common treatment for this syndrome, and this study was conducted to compare the effect of auriculotherapy and vitamin B6 on the symptoms of premenstrual syndrome. This study was a clinical trial. Eighty-four female students who lived at the university dorm were randomly selected and allocated into two groups of 42. The first group received auriculotherapy (10 sessions) for two menstrual cycles and the second group consumed 40 mg of vitamin B6 daily from a week before their menstruation for two menstrual cycles. The severity of symptoms was recorded for both groups during two cycles before the intervention and two cycles after the intervention. Data gathering tool was a 28-question, questionnaire to assess the severity of symptoms of premenstrual syndrome based on DSM-IV. The mean score of symptoms in the auriculotherapy group in the first and second cycles was 26.70 (19.49) and 24.76 (17.07), respectively, and in the vitamin B6 group, was 22.60 (10.87) and 24.17 (14.15), respectively, which showed a significant difference compared to before the intervention ( P = 0.001). However, comparing the total score of symptoms in the first and second cycles after the intervention between both groups showed no significant difference. Auriculotherapy, similar to vitamin B6, decreases the severity of PMS symptoms.

Chronic sciatic neuropathy in rat reduces voluntary wheel running activity with concurrent chronic mechanical allodynia

PubMed Central

Whitehead, RA; Lam, NL; Sun, MS; Sanchez, JJ; Noor, S; Vanderwall, AG; Petersen, TR; Martin, HB

2016-01-01

BACKGROUND Animal models of peripheral neuropathy produced by a number of manipulations are assessed for the presence of pathological pain states such as allodynia. While stimulus-induced behavioral assays are frequently used and important to examine allodynia (i.e. sensitivity to light mechanical touch; von Frey fiber test) other measures of behavior that reflect overall function are not only complementary to stimulus-induced responsive measures, but are also critical to gain a complete understanding of the effects of the pain model on quality of life, a clinically relevant aspect of pain on general function. Voluntary wheel running activity in rodent models of inflammatory and muscle pain is emerging as a reliable index of general function that extends beyond stimulus-induced behavioral assays. Clinically, reports of increased pain intensity occur at night, a period typically characterized with reduced activity during the diurnal cycle. We therefore examined in rats whether alterations in wheel running activity were more robust during the inactive phase compared to the active phase of their diurnal cycle in a widely used rodent model of chronic peripheral neuropathic pain, the sciatic nerve chronic constriction injury (CCI) model. METHODS In adult male Sprague Dawley rats, baseline (BL) hindpaw threshold responses to light mechanical touch were assessed using the von Frey test prior to measuring BL activity levels using freely accessible running wheels (1 hr/day for 7 sequential days) to quantify distance traveled. Running wheel activity BL values are expressed as total distance traveled (m). The overall experimental design was: following BL measures, rats underwent either sham or CCI surgery followed by repeated behavioral re-assessment of hindpaw thresholds and wheel running activity levels for up to 18 days after surgery. Specifically, separate groups of rats were assessed for wheel running activity levels (1 hr total/trial) during the onset (within first 2 hrs) of either the (1) inactive (n=8/gp) or (2) active (n = 8/gp) phase of the diurnal cycle. An additional group of CCI-treated rats (n = 8/gp) were exposed to a locked running wheel to control for the potential effects of wheel running exercise on allodynia. The 1-hr running wheel trial period was further examined at discrete 20-min intervals to identify possible pattern differences in activity during the first, middle and last portion of the 1-hr trial. The effect of neuropathy on activity levels were assessed by measuring the change from their respective BLs to distance traveled in the running wheels. RESULTS While wheel running distances between groups were not different at BL from rats examined during either the inactive phase of the diurnal cycle or active phase of the diurnal cycle, sciatic nerve CCI reduced running wheel activity levels compared to sham-operated controls during the inactive phase. Additionally, compared to sham controls, bilateral low threshold mechanical allodynia was observed at all time-points after surgical induction of neuropathy in rats with free-wheel and locked-wheel access. Allodynia in CCI compared to shams was replicated in rats whose running wheel activity was examined during the active phase of the diurnal cycle. Conversely, no significant reduction in wheel running activity was observed in CCI-treated rats compared to sham controls at any timepoint when activity levels were examined during the active diurnal phase. Lastly, running wheel activity patterns within the 1 hr trial period during the inactive phase of the diurnal cycle were relatively consistent throughout each 20 min phase. CONCLUSIONS Compared to non-neuropathic sham controls, a profound and stable reduction of running wheel activity was observed in CCI rats during the inactive phase of the diurnal cycle. A concurrent robust allodynia persisted in all rats regardless of when wheel running activity was examined or whether they ran on wheels, suggesting that acute wheel running activity does not alter chronic low intensity mechanical allodynia as measured using the von Frey fiber test. Overall, these data support that acute wheel running exercise with limited repeated exposures does not itself alter allodynia and offers a behavioral assay complementary to stimulus-induced measures of neuropathic pain. PMID:27782944

Life Cycle Water Consumption and Wastewater Generation Impacts of a Marcellus Shale Gas Well

PubMed Central

2013-01-01

This study estimates the life cycle water consumption and wastewater generation impacts of a Marcellus shale gas well from its construction to end of life. Direct water consumption at the well site was assessed by analysis of data from approximately 500 individual well completion reports collected in 2010 by the Pennsylvania Department of Conservation and Natural Resources. Indirect water consumption for supply chain production at each life cycle stage of the well was estimated using the economic input–output life cycle assessment (EIO-LCA) method. Life cycle direct and indirect water quality pollution impacts were assessed and compared using the tool for the reduction and assessment of chemical and other environmental impacts (TRACI). Wastewater treatment cost was proposed as an additional indicator for water quality pollution impacts from shale gas well wastewater. Four water management scenarios for Marcellus shale well wastewater were assessed: current conditions in Pennsylvania; complete discharge; direct reuse and desalination; and complete desalination. The results show that under the current conditions, an average Marcellus shale gas well consumes 20 000 m3 (with a range from 6700 to 33 000 m3) of freshwater per well over its life cycle excluding final gas utilization, with 65% direct water consumption at the well site and 35% indirect water consumption across the supply chain production. If all flowback and produced water is released into the environment without treatment, direct wastewater from a Marcellus shale gas well is estimated to have 300–3000 kg N-eq eutrophication potential, 900–23 000 kg 2,4D-eq freshwater ecotoxicity potential, 0–370 kg benzene-eq carcinogenic potential, and 2800–71 000 MT toluene-eq noncarcinogenic potential. The potential toxicity of the chemicals in the wastewater from the well site exceeds those associated with supply chain production, except for carcinogenic effects. If all the Marcellus shale well wastewater is treated to surface discharge standards by desalination, $59 000–270 000 per well would be required. The life cycle study results indicate that when gas end use is not considered hydraulic fracturing is the largest contributor to the life cycle water impacts of a Marcellus shale gas well. PMID:24380628

Lean methodology improves efficiency in outpatient academic uro-oncology clinics.

PubMed

Skeldon, Sean C; Simmons, Andrea; Hersey, Karen; Finelli, Antonio; Jewett, Michael A; Zlotta, Alexandre R; Fleshner, Neil E

2014-05-01

To determine if lean methodology, an industrial engineering tool developed to optimize manufacturing efficiency, can successfully be applied to improve efficiencies and quality of care in a hospital-based high-volume uro-oncology clinic. Before the lean initiative, baseline data were collected on patient volumes, wait times, cycle times (patient arrival to discharge), nursing assessment time, patient teaching, and physician ergonomics (via spaghetti diagram). Value stream analysis and a rapid improvement event were carried out, and significant changes were made to patient check-in, work areas, and nursing face time. Follow-up data were obtained at 30, 60, and 90 days. The Student t test was used for analysis to compare performance metrics with baseline. The median cycle time before the lean initiative was 46 minutes. This remained stable at 46 minutes at 30 days but improved to 35 minutes at 60 days and 41 minutes at 90 days. Shorter wait times allowed for increased nursing and physician face time. The average length of the physician assessment increased from 7.5 minutes at baseline to 10.6 minutes at 90 days. The average proportion of value-added time compared with the entire clinic visit increased from 30.6% at baseline to 66.3% at 90 days. Using lean methodology, we were able to shorten the patient cycle time and the time to initial assessment as well as integrate both an initial registered nurse assessment and registered nurse teaching to each visit. Lean methodology can effectively be applied to improve efficiency and patient care in an academic outpatient uro-oncology clinic setting. Copyright © 2014 Elsevier Inc. All rights reserved.

Exploring the life cycle management of industrial solid waste in the case of copper slag.

PubMed

Song, Xiaolong; Yang, Jianxin; Lu, Bin; Li, Bo

2013-06-01

Industrial solid waste has potential impacts on soil, water and air quality, as well as human health, during its whole life stages. A framework for the life cycle management of industrial solid waste, which integrates the source reduction process, is presented and applied to copper slag management. Three management scenarios of copper slag are developed: (i) production of cement after electric furnace treatment, (ii) production of cement after flotation, and (iii) source reduction before the recycling process. A life cycle assessment is carried out to estimate the environmental burdens of these three scenarios. Life cycle assessment results showed that the environmental burdens of the three scenarios are 2710.09, 2061.19 and 2145.02 Pt respectively. In consideration of the closed-loop recycling process, the environmental performance of the flotation approach excelled that of the electric furnace approach. Additionally, although flash smelting promotes the source reduction of copper slag compared with bath smelting, it did not reduce the overall environmental burdens resulting from the complete copper slag management process. Moreover, it led to the shifting of environmental burdens from ecosystem quality damage and resources depletion to human health damage. The case study shows that it is necessary to integrate the generation process into the whole life cycle of industrial solid waste, and to make an integrated assessment for quantifying the contribution of source reduction, rather than to simply follow the priority of source reduction and the hierarchy of waste management.

GEOSAT Follow-On (GFO) Altimeter Document Series, Volume 9. GFO and JASON Altimeter Engineering Assessment Report Update: GFO-Acceptance to December 18, 2006, JASON-Acceptance to December 24, 2006. Version 1: June 2007

NASA Technical Reports Server (NTRS)

Hayne, G. S.; Hancock, D. W., III; Brooks, R. L.

2007-01-01

The initial GFO Altimeter Engineering Assessment Report, March 2001 (NASA/TM-2001-209984/Ver.1/Vol.1) covered the GFO performance from Launch to Acceptance (10 February 1998 to 29 November 2000). The second of the series covered the performance from Acceptance to the end of Cycle 20 (29 November 2000 to 21 November 2001). The third of the series covered the performance from Acceptance to the end of Cycle 42 (29 November 2000 to 30 November 2002). The fourth of the series covered the performance from Acceptance to the end of Cycle 64 (29 November 2000 to 17 December 2003). The fifth of the series covered performance from Acceptance to the end of Cycle 86 (29 November 2000 to 17 December 2004). The sixth of the series covered performance from Acceptance to the end of Cycle 109 (29 November 2000 to 26 December 2005). In this year's GFO report, we have begun the inclusion of analyses of the JASON altimeter. In past years, JASON and TOPEX were compared during our assessment of the TOPEX altimeter; however, with the end of the TOPEX mission, we have developed methods to report on JASON as it relates to GFO. We see no change trend between the three altimeters and conclude all three are stable based on our cross comparison analyses.

WaLA, a versatile model for the life cycle assessment of urban water systems: Formalism and framework for a modular approach.

PubMed

Loubet, Philippe; Roux, Philippe; Bellon-Maurel, Véronique

2016-01-01

The emphasis on the sustainable urban water management has increased over the last decades. In this context decision makers need tools to measure and improve the environmental performance of urban water systems (UWS) and their related scenarios. In this paper, we propose a versatile model, named WaLA (Water system Life cycle Assessment), which reduces the complexity of the UWS while ensuring a good representation of water issues and fulfilling life cycle assessment (LCA) requirements. Indeed, LCAs require building UWS models, which can be tedious if several scenarios are to be compared. The WaLA model is based on a framework that uses a "generic component" representing alternately water technology units and water users, with their associated water flows, and the associated impacts due to water deprivation, emissions, operation and infrastructure. UWS scenarios can be built by inter-operating and connecting the technologies and users components in a modular and integrated way. The model calculates life cycle impacts at a monthly temporal resolution for a set of services provided to users, as defined by the scenario. It also provides the ratio of impacts to amount of services provided and useful information for UWS diagnosis or comparison of different scenarios. The model is implemented in a Matlab/Simulink interface thanks to object-oriented programming. The applicability of the model is demonstrated using a virtual case study based on available life cycle inventory data. Copyright © 2015 Elsevier Ltd. All rights reserved.

Reducing impacts from ammunitions: A comparative life-cycle assessment of four types of 9mm ammunitions.

PubMed

Ferreira, Carlos; Ribeiro, José; Almada, Sara; Rotariu, Traian; Freire, Fausto

2016-10-01

Increase of environmental awareness of the population has pressured research activities in the defence area to cover environment and toxicity issues, where have been considered appropriate manners to reduce the environmental and toxicological impacts of ammunition. One of the adopted approaches to achieve such goal involves the replacement of lead and other heavy metals by alternative materials. However, the consequences of using alternative materials in ammunitions manufacturing are uncertain for the other life-cycle phases and trade-offs can occur. The present paper describes the potential benefits from the replacement of lead in the primer and in the projectile of a 9mm calibre ammunition. For that purpose, it is assessed and compared the environmental and toxicological impacts associated with the life-cycle of four ammunitions: combination of two types of projectiles (steel jacket and lead core; copper and nylon composite) with two types of primers (lead primer; non-lead primer). In addition, some potential improvements for the environmental performance of small calibre ammunition are also presented. To assess the impacts two Life-Cycle Impact Assessment methods are applied: CML for six environmental categories and USEtox to three toxicity categories. Results showed that the conclusion drawn for environmental and toxicological impact categories are distinct. In fact, ammunition production phase presents higher impacts for the environmental categories, whilst the operation phase has a higher impact to the toxicity categories. The substitution of lead in the primer and in the projectile provides a suitable alternative from a toxicology perspective; however, the composite projectile still presents some environmental concerns. The conclusions drawn are important for the procurement (and design) of environmental responsible ammunitions, in order to avoid (or decrease) the impacts for their manufacture and the effects on human health (e.g. shooters) and ecosystems near shooting ranges or hunting areas. Copyright © 2016 Elsevier B.V. All rights reserved.

Developing Product Environmental Footprint Category Rules (PEFCR) for shampoos - The basis for comparable Life Cycle Assessments.

PubMed

Golsteijn, Laura; Lessard, Lindsay; Campion, Jean-Florent; Capelli, Alexandre; D'Enfert, Virginie; King, Henry; Kremer, Joachim; Krugman, Michael; Orliac, Hélène; Furnemont, Severine Roullet; Schuh, Werner; Stalmans, Mark; O'Hanlon, Natasha Williams; Coroama, Manuela

2018-06-05

In 2013, the European Commission launched the Environmental Footprint Rules pilot phase. This initiative aims at setting specific rules for life cycle assessment (LCA: raw material sourcing, production, logistics, use- and disposal phase) studies within one product category, so called product environmental footprint category rules (PEFCR), as well as for organisations, so called organisational environmental footprint sector rules (OEFSR). Such specific rules for measuring environmental performance throughout the life cycle should facilitate the comparability between LCA studies, and provide principles for communicating the environmental performance, such as transparency, reliability, completeness, and clarity. Cosmetics Europe, the association representing the cosmetics industry in the EU, completed a voluntary study into the development of PEFCR for shampoo, generally following the guidelines and methodology developed by the European Commission for its own pilot projects. The study assessed the feasibility and relevance of establishing PEFCR for shampoo. Specifically, the study defines a large number of modelling assumptions and default values relevant for shampoo (e.g. for the functional unit, the system boundaries, default transport distances, rinsing water volumes, temperature differences, life cycle inventory data sources etc) that can be modified as appropriate, according to specificities of individual products, manufacturing companies and countries. The results of the study may be used to support internal decision-making (e.g. to identify 'hotspots' with high environmental impact and opportunities for improvement) or to meet information requests from commercial partners, consumers, media or authorities on product environmental characteristics. In addition, the shampoo study also highlighted many of the challenges and limitations of the current PEF methodology, namely its complexity and resource intensiveness. It highlighted two areas where improvements are much needed: (1) data quality and availability, and (2) impact assessment methodologies and robustness. Many of the learnings are applicable to other rinse-off cosmetic products such as shower gels, liquid soaps, bath products and hair conditioners. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Life Cycle Assessment of Solar Photovoltaic Microgrid Systems in Off-Grid Communities.

PubMed

Bilich, Andrew; Langham, Kevin; Geyer, Roland; Goyal, Love; Hansen, James; Krishnan, Anjana; Bergesen, Joseph; Sinha, Parikhit

2017-01-17

Access to a reliable source of electricity creates significant benefits for developing communities. Smaller versions of electricity grids, known as microgrids, have been developed as a solution to energy access problems. Using attributional life cycle assessment, this project evaluates the environmental and energy impacts of three photovoltiac (PV) microgrids compared to other energy options for a model village in Kenya. When normalized per kilowatt hour of electricity consumed, PV microgrids, particularly PV-battery systems, have lower impacts than other energy access solutions in climate change, particulate matter, photochemical oxidants, and terrestrial acidification. When compared to small-scale diesel generators, PV-battery systems save 94-99% in the above categories. When compared to the marginal electricity grid in Kenya, PV-battery systems save 80-88%. Contribution analysis suggests that electricity and primary metal use during component, particularly battery, manufacturing are the largest contributors to overall PV-battery microgrid impacts. Accordingly, additional savings could be seen from changing battery manufacturing location and ensuring end of life recycling. Overall, this project highlights the potential for PV microgrids to be feasible, adaptable, long-term energy access solutions, with health and environmental advantages compared to traditional electrification options.

Life cycle greenhouse gas emissions and freshwater consumption associated with Bakken tight oil

PubMed Central

Laurenzi, Ian J.; Bergerson, Joule A.; Motazedi, Kavan

2016-01-01

In recent years, hydraulic fracturing and horizontal drilling have been applied to extract crude oil from tight reservoirs, including the Bakken formation. There is growing interest in understanding the greenhouse gas (GHG) emissions associated with the development of tight oil. We conducted a life cycle assessment of Bakken crude using data from operations throughout the supply chain, including drilling and completion, refining, and use of refined products. If associated gas is gathered throughout the Bakken well life cycle, then the well to wheel GHG emissions are estimated to be 89 g CO2eq/MJ (80% CI, 87–94) of Bakken-derived gasoline and 90 g CO2eq/MJ (80% CI, 88–94) of diesel. If associated gas is flared for the first 12 mo of production, then life cycle GHG emissions increase by 5% on average. Regardless of the level of flaring, the Bakken life cycle GHG emissions are comparable to those of other crudes refined in the United States because flaring GHG emissions are largely offset at the refinery due to the physical properties of this tight oil. We also assessed the life cycle freshwater consumptions of Bakken-derived gasoline and diesel to be 1.14 (80% CI, 0.67–2.15) and 1.22 barrel/barrel (80% CI, 0.71–2.29), respectively, 13% of which is associated with hydraulic fracturing. PMID:27849573

Is there an ideal stimulation regimen for IVF for poor responders and does it change with age?

PubMed Central

Osianlis, Tiki; Catt, James

2008-01-01

Purpose To determine whether there is a superior treatment modality for ‘poor’ responders. Method Retrospective analysis of three stimulation regimens, with patients stratified based on age, stimulation regime and response in previous cycles (“poor’ responder or “non poor” responder). Fertilisation, embryo utilisation and clinical pregnancy rates were assessed. There were a total of 1,608 cycles in the ‘poor’ responder and 8,489 cycles in the ‘non poor’ responder groups. Results In ‘poor’ responders there was no significant difference in fertilisation rate, nor utilisation rate between the three stimulation regimes and no differences in the pregnancy rate/initiated cycle irrespective of age and stimulation regimen in any of the groups. ‘Non poor’ responders had a significantly greater pregnancy rate/initiated cycle for all stimulation regimens in both age groups compared with ‘poor’ responders. Conclusion This large retrospective study of ‘poor’ responders has not shown a difference in pregnancy rates/initiated cycle between stimulation regimens. PMID:18982442

THE ECONOMICS OF REPROCESSING vs DIRECT DISPOSAL OF SPENT NUCLEAR FUEL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthew Bunn; Steve Fetter; John P. Holdren

This report assesses the economics of reprocessing versus direct disposal of spent nuclear fuel. The breakeven uranium price at which reprocessing spent nuclear fuel from existing light-water reactors (LWRs) and recycling the resulting plutonium and uranium in LWRs would become economic is assessed, using central estimates of the costs of different elements of the nuclear fuel cycle (and other fuel cycle input parameters), for a wide range of range of potential reprocessing prices. Sensitivity analysis is performed, showing that the conclusions reached are robust across a wide range of input parameters. The contribution of direct disposal or reprocessing and recyclingmore » to electricity cost is also assessed. The choice of particular central estimates and ranges for the input parameters of the fuel cycle model is justified through a review of the relevant literature. The impact of different fuel cycle approaches on the volume needed for geologic repositories is briefly discussed, as are the issues surrounding the possibility of performing separations and transmutation on spent nuclear fuel to reduce the need for additional repositories. A similar analysis is then performed of the breakeven uranium price at which deploying fast neutron breeder reactors would become competitive compared with a once-through fuel cycle in LWRs, for a range of possible differences in capital cost between LWRs and fast neutron reactors. Sensitivity analysis is again provided, as are an analysis of the contribution to electricity cost, and a justification of the choices of central estimates and ranges for the input parameters. The equations used in the economic model are derived and explained in an appendix. Another appendix assesses the quantities of uranium likely to be recoverable worldwide in the future at a range of different possible future prices.« less

Validity and reliability of the PowerTap mobile cycling powermeter when compared with the SRM Device.

PubMed

Bertucci, W; Duc, S; Villerius, V; Pernin, J N; Grappe, F

2005-12-01

The SRM power measuring crank system is nowadays a popular device for cycling power output (PO) measurements in the field and in laboratories. The PowerTap (CycleOps, Madison, USA) is a more recent and less well-known device that allows mobile PO measurements of cycling via the rear wheel hub. The aim of this study is to test the validity and reliability of the PowerTap by comparing it with the most accurate (i.e. the scientific model) of the SRM system. The validity of the PowerTap is tested during i) sub-maximal incremental intensities (ranging from 100 to 420 W) on a treadmill with different pedalling cadences (45 to 120 rpm) and cycling positions (standing and seated) on different grades, ii) a continuous sub-maximal intensity lasting 30 min, iii) a maximal intensity (8-s sprint), and iiii) real road cycling. The reliability is assessed by repeating ten times the sub-maximal incremental and continuous tests. The results show a good validity of the PowerTap during sub-maximal intensities between 100 and 450 W (mean PO difference -1.2 +/- 1.3 %) when it is compared to the scientific SRM model, but less validity for the maximal PO during sprint exercise, where the validity appears to depend on the gear ratio. The reliability of the PowerTap during the sub-maximal intensities is similar to the scientific SRM model (the coefficient of variation is respectively 0.9 to 2.9 % and 0.7 to 2.1 % for PowerTap and SRM). The PowerTap must be considered as a suitable device for PO measurements during sub-maximal real road cycling and in sub-maximal laboratory tests.

Selection of alternative central-station technologies for the Satellite Power System (SPS) comparative assessment

NASA Technical Reports Server (NTRS)

Samsa, M.

1980-01-01

An important effort is the Satellite Power System (SPS) comparative Assessment is the selection and characterization of alternative technologies to be compared with the SPS concept. The ground rules, criteria, and screening procedure applied in the selection of those alternative technologies are summarized. The final set of central station alternatives selected for comparison with the SPS concept includes: (1) light water reactor with improved fuel utilization, (2) conventional coal combustion with improved environmental controls, (3) open cycle gas turbine with integral low Btu gasifier, (4) terrestrial photovoltaic, (5) liquid metal fast breeder reactor, and (6) magnetic confinement fusion.

Performance comparison of different thermodynamic cycles for an innovative central receiver solar power plant

NASA Astrophysics Data System (ADS)

Reyes-Belmonte, Miguel A.; Sebastián, Andrés; González-Aguilar, José; Romero, Manuel

2017-06-01

The potential of using different thermodynamic cycles coupled to a solar tower central receiver that uses a novel heat transfer fluid is analyzed. The new fluid, named as DPS, is a dense suspension of solid particles aerated through a tubular receiver used to convert concentrated solar energy into thermal power. This novel fluid allows reaching high temperatures at the solar receiver what opens a wide range of possibilities for power cycle selection. This work has been focused into the assessment of power plant performance using conventional, but optimized cycles but also novel thermodynamic concepts. Cases studied are ranging from subcritical steam Rankine cycle; open regenerative Brayton air configurations at medium and high temperature; combined cycle; closed regenerative Brayton helium scheme and closed recompression supercritical carbon dioxide Brayton cycle. Power cycle diagrams and working conditions for design point are compared amongst the studied cases for a common reference thermal power of 57 MWth reaching the central cavity receiver. It has been found that Brayton air cycle working at high temperature or using supercritical carbon dioxide are the most promising solutions in terms of efficiency conversion for the power block of future generation by means of concentrated solar power plants.

The quality of operative note taking: an audit using the Royal College of Surgeons Guidelines as the gold standard.

PubMed

Shayah, A; Agada, F O; Gunasekaran, S; Jassar, P; England, R J A

2007-04-01

To assess the quality of operative note keeping and compare the results with the Royal College of Surgeons (RCS) of England guidelines 'Good Surgical Practice' as the gold standard. ENT Department at Hull Royal Infirmary, University Hospital. A hundred consecutive operative notes were selected between November 2005 and January 2006. The documentation of the operative notes in each case was compared with the RCS of England guidelines. All surgeons were made aware of the results of the first cycle and the guidelines were made available in all ENT theatres in the form of a printed aide-memoir. A second audit cycle was then carried out prospectively between April and June 2006. The results demonstrated a change in practice in key areas. The 1st cycle results showed the documentation of patient identification (94%), name of surgeon (98%) and clearly written postoperative instructions (94%). However, surgeons performed suboptimally at recording the name of assistant (82%), operative diagnosis (46%), the incision type (87%) and the type of wound closure (83%). After introducing the aide-memoir, the second cycle demonstrated a change in practice with 100% documentation in most of the assessed parameters except that the time of surgery and the type of surgery (emergency or elective) were not adequately recorded. We recommend that all surgical departments should have the RCS guidelines as an aide-memoir in theatres to enhance the quality and standardise operative note recording.

Including exposure variability in the life cycle impact assessment of indoor chemical emissions: the case of metal degreasing.

PubMed

Golsteijn, Laura; Huizer, Daan; Hauck, Mara; van Zelm, Rosalie; Huijbregts, Mark A J

2014-10-01

The present paper describes a method that accounts for variation in indoor chemical exposure settings and accompanying human toxicity in life cycle assessment (LCA). Metal degreasing with dichloromethane was used as a case study to show method in practice. We compared the human toxicity related to the degreasing of 1m(2) of metal surface in different exposure scenarios for industrial workers, professional users outside industrial settings, and home consumers. The fraction of the chemical emission that is taken in by exposed individuals (i.e. the intake fraction) was estimated on the basis of operational conditions (e.g. exposure duration), and protective measures (e.g. local exhaust ventilation). The introduction of a time-dependency and a correction for protective measures resulted in reductions in the intake fraction of up to 1.5 orders of magnitude, compared to application of existing, less advanced models. In every exposure scenario, the life cycle impacts for human toxicity were mainly caused by indoor exposure to metal degreaser (>60%). Emissions released outdoors contributed up to 22% of the life cycle impacts for human toxicity, and the production of metal degreaser contributed up to 19%. These findings illustrate that human toxicity from indoor chemical exposure should not be disregarded in LCA case studies. Particularly when protective measures are taken or in the case of a short duration (1h or less), we recommend the use of our exposure scenario-specific approach. Copyright © 2014 Elsevier Ltd. All rights reserved.

Reliability and validity of four alternative definitions of rapid-cycling bipolar disorder.

PubMed

Maj, M; Pirozzi, R; Formicola, A M; Tortorella, A

1999-09-01

This study tested the reliability and validity of four definitions of rapid cycling. Two trained psychiatrists, using the Schedule for Affective Disorders and Schizophrenia, independently assessed 210 patients with bipolar disorder. They checked whether each patient met four definitions of rapid cycling: one consistent with DSM-IV criteria, one waiving criteria for duration of affective episodes, one waiving such criteria and requiring at least one switch from mania to depression or vice versa during the reference year, and one waiving duration criteria and requiring at least 8 weeks of fully symptomatic affective illness during the reference year. The interrater reliability was calculated by Cohen's kappa statistic. Patients who met each definition according to both psychiatrists were compared to those who did not meet any definition (nonrapid-cycling group) on demographic and clinical variables. All patients were followed up for 1 year. Kappa values were 0.93, 0.73, 0.75, and 0.80, respectively, for the four definitions of rapid cycling. The groups meeting the second and third definitions included significantly more female and bipolar II patients than did the nonrapid-cycling group. Those two groups also had the lowest proportion of patients with a favorable lithium prophylaxis outcome and the highest stability of the rapid-cycling pattern on follow-up. The four groups of rapid-cycling patients did not differ significantly among themselves on any of the assessed variables. The expression "rapid cycling" encompasses a spectrum of conditions. The DSM-IV definition, although quite reliable, covers only part of this spectrum, and the conditions that are excluded are very typical in terms of key validators and are relatively stable over time.

Integrated Assessment of Carbon Dioxide Removal

NASA Astrophysics Data System (ADS)

Rickels, W.; Reith, F.; Keller, D.; Oschlies, A.; Quaas, M. F.

2018-03-01

To maintain the chance of keeping the average global temperature increase below 2°C and to limit long-term climate change, removing carbon dioxide from the atmosphere (carbon dioxide removal, CDR) is becoming increasingly necessary. We analyze optimal and cost-effective climate policies in the dynamic integrated assessment model (IAM) of climate and the economy (DICE2016R) and investigate (1) the utilization of (ocean) CDR under different climate objectives, (2) the sensitivity of policies with respect to carbon cycle feedbacks, and (3) how well carbon cycle feedbacks are captured in the carbon cycle models used in state-of-the-art IAMs. Overall, the carbon cycle model in DICE2016R shows clear improvements compared to its predecessor, DICE2013R, capturing much better long-term dynamics and also oceanic carbon outgassing due to excess oceanic storage of carbon from CDR. However, this comes at the cost of a (too) tight short-term remaining emission budget, limiting the model suitability to analyze low-emission scenarios accurately. With DICE2016R, the compliance with the 2°C goal is no longer feasible without negative emissions via CDR. Overall, the optimal amount of CDR has to take into account (1) the emission substitution effect and (2) compensation for carbon cycle feedbacks.

Carbon-Carbon Recuperators in Closed-Brayton-Cycle Space Power Systems

NASA Technical Reports Server (NTRS)

Barrett, Michael J.; Johnson, Paul K.

2006-01-01

The use of carbon-carbon (C-C) recuperators in closed-Brayton-cycle space power conversion systems was assessed. Recuperator performance was forecast based on notional thermodynamic cycle state values for planetary missions. Resulting thermal performance, mass and volume for plate-fin C-C recuperators were estimated and quantitatively compared with values for conventional offset-strip-fin metallic designs. Mass savings of 40-55% were projected for C-C recuperators with effectiveness greater than 0.9 and thermal loads from 25-1400 kWt. The smaller thermal loads corresponded with lower mass savings; however, at least 50% savings were forecast for all loads above 300 kWt. System-related material challenges and compatibility issues were also discussed.

Hybrid systems for transuranic waste transmutation in nuclear power reactors: state of the art and future prospects

NASA Astrophysics Data System (ADS)

Yurov, D. V.; Prikhod'ko, V. V.

2014-11-01

The features of subcritical hybrid systems (HSs) are discussed in the context of burning up transuranic wastes from the U-Pu nuclear fuel cycle. The advantages of HSs over conventional atomic reactors are considered, and fuel cycle closure alternatives using HSs and fast neutron reactors are comparatively evaluated. The advantages and disadvantages of two HS types with neutron sources (NSs) of widely different natures -- nuclear spallation in a heavy target by protons and nuclear fusion in magnetically confined plasma -- are discussed in detail. The strengths and weaknesses of HSs are examined, and demand for them for closing the U-Pu nuclear fuel cycle is assessed.

Assessment of steam-injected gas turbine systems and their potential application

NASA Technical Reports Server (NTRS)

Stochl, R. J.

1982-01-01

Results were arrived at by utilizing and expanding on information presented in the literature. The results were analyzed and compared with those for simple gas turbine and combined cycles for both utility power generation and industrial cogeneration applications. The efficiency and specific power of simple gas turbine cycles can be increased as much as 30 and 50 percent, respectively, by the injection of steam into the combustor. Steam-injected gas turbines appear to be economically competitive with both simple gas turbine and combined cycles for small, clean-fuel-fired utility power generation and industrial cogeneration applications. For large powerplants with integrated coal gasifiers, the economic advantages appear to be marginal.

Systematic Standardized and Individualized Assessment of Masticatory Cycles Using Electromagnetic 3D Articulography and Computer Scripts

PubMed Central

Arias, Alain; Lezcano, María Florencia; Saravia, Diego; Dias, Fernando José

2017-01-01

Masticatory movements are studied for decades in odontology; a better understanding of them could improve dental treatments. The aim of this study was to describe an innovative, accurate, and systematic method of analyzing masticatory cycles, generating comparable quantitative data. The masticatory cycles of 5 volunteers (Class I, 19 ± 1.7 years) without articular or dental occlusion problems were evaluated using 3D electromagnetic articulography supported by MATLAB software. The method allows the trajectory morphology of the set of chewing cycles to be analyzed from different views and angles. It was also possible to individualize the trajectory of each cycle providing accurate quantitative data, such as number of cycles, cycle areas in frontal view, and the ratio between each cycle area and the frontal mandibular border movement area. There was a moderate negative correlation (−0.61) between the area and the number of cycles: the greater the cycle area, the smaller the number of repetitions. Finally it was possible to evaluate the area of the cycles through time, which did not reveal a standardized behavior. The proposed method provided reproducible, intelligible, and accurate quantitative and graphical data, suggesting that it is promising and may be applied in different clinical situations and treatments. PMID:29075647

Systematic Standardized and Individualized Assessment of Masticatory Cycles Using Electromagnetic 3D Articulography and Computer Scripts.

PubMed

Fuentes, Ramón; Arias, Alain; Lezcano, María Florencia; Saravia, Diego; Kuramochi, Gisaku; Dias, Fernando José

2017-01-01

Masticatory movements are studied for decades in odontology; a better understanding of them could improve dental treatments. The aim of this study was to describe an innovative, accurate, and systematic method of analyzing masticatory cycles, generating comparable quantitative data. The masticatory cycles of 5 volunteers (Class I, 19 ± 1.7 years) without articular or dental occlusion problems were evaluated using 3D electromagnetic articulography supported by MATLAB software. The method allows the trajectory morphology of the set of chewing cycles to be analyzed from different views and angles. It was also possible to individualize the trajectory of each cycle providing accurate quantitative data, such as number of cycles, cycle areas in frontal view, and the ratio between each cycle area and the frontal mandibular border movement area. There was a moderate negative correlation (-0.61) between the area and the number of cycles: the greater the cycle area, the smaller the number of repetitions. Finally it was possible to evaluate the area of the cycles through time, which did not reveal a standardized behavior. The proposed method provided reproducible, intelligible, and accurate quantitative and graphical data, suggesting that it is promising and may be applied in different clinical situations and treatments.

Life cycle assessment part 1: framework, goal and scope definition, inventory analysis, and applications.

PubMed

Rebitzer, G; Ekvall, T; Frischknecht, R; Hunkeler, D; Norris, G; Rydberg, T; Schmidt, W-P; Suh, S; Weidema, B P; Pennington, D W

2004-07-01

Sustainable development requires methods and tools to measure and compare the environmental impacts of human activities for the provision of goods and services (both of which are summarized under the term "products"). Environmental impacts include those from emissions into the environment and through the consumption of resources, as well as other interventions (e.g., land use) associated with providing products that occur when extracting resources, producing materials, manufacturing the products, during consumption/use, and at the products' end-of-life (collection/sorting, reuse, recycling, waste disposal). These emissions and consumptions contribute to a wide range of impacts, such as climate change, stratospheric ozone depletion, tropospheric ozone (smog) creation, eutrophication, acidification, toxicological stress on human health and ecosystems, the depletion of resources, water use, land use, and noise-among others. A clear need, therefore, exists to be proactive and to provide complimentary insights, apart from current regulatory practices, to help reduce such impacts. Practitioners and researchers from many domains come together in life cycle assessment (LCA) to calculate indicators of the aforementioned potential environmental impacts that are linked to products-supporting the identification of opportunities for pollution prevention and reductions in resource consumption while taking the entire product life cycle into consideration. This paper, part 1 in a series of two, introduces the LCA framework and procedure, outlines how to define and model a product's life cycle, and provides an overview of available methods and tools for tabulating and compiling associated emissions and resource consumption data in a life cycle inventory (LCI). It also discusses the application of LCA in industry and policy making. The second paper, by Pennington et al. (Environ. Int. 2003, in press), highlights the key features, summarises available approaches, and outlines the key challenges of assessing the aforementioned inventory data in terms of contributions to environmental impacts (life cycle impact assessment, LCIA).

Optoacoustic Imaging Detects Hormone-Related Physiological Changes of Breast Parenchyma.

PubMed

Abeyakoon, Oshaani; Morscher, Stefan; Dalhaus, Nina; Ford, Steven J; Mendichovszky, Iosif A; Manavaki, Roido; Wallis, Matthew; Moyle, Penelope; Woitek, Ramona; Patterson, Andrew; Torheim, Turid; Joseph, James; Gonzalez, Isabel Quiros; Bohndiek, Sarah; Gilbert, Fiona J

2018-06-07

 Optoacoustic imaging with ultrasound (OPUS) can assess in-vivo perfusion/oxygenation through surrogate measures of oxy, deoxy and total hemoglobin content in tissues. The primary aim of our study was to evaluate the ability of OPUS to detect physiological changes in the breast during the menstrual cycle and to determine qualitative/quantitative metrics of normal parenchymal tissue in pre-/post-menopausal women. The secondary aim was to assess the technique's repeatability.  We performed a prospective ethically approved study in volunteers using OPUS (700, 800 and 850 nm wavelengths) in the proliferative/follicular and secretory phase of the menstrual cycle. Regions of interest (ROIs) were drawn on the most superficial region of fibroglandular tissue and same-day intra-observer repeatability was assessed. We used t-tests to interrogate differences in the OPUS measurements due to hormonal changes and interclass correlation coefficients/Bland-Altman plots to evaluate the repeatability of mean ROI signal intensities.  22 pre-menopausal and 8 post-menopausal volunteers were recruited. 21 participants underwent repeatability examinations. OPUS intensity values were significantly higher (p < 0.0001) at all excitation wavelengths in the secretory compared to the proliferative/follicular phase. Post-menopausal volunteers showed similar optoacoustic values to the proliferative/follicular phase of pre-menopausal volunteers. The repeatability of the technique was comparable to other handheld ultrasound modalities.  OPUS detects changes in perfusion/vascularity related to the menstrual cycle and menopausal status of breast parenchyma. © Georg Thieme Verlag KG Stuttgart · New York.

Technical, hygiene, economic, and life cycle assessment of full-scale moving bed biofilm reactors for wastewater treatment in India.

PubMed

Singh, Anju; Kamble, Sheetal Jaisingh; Sawant, Megha; Chakravarthy, Yogita; Kazmi, Absar; Aymerich, Enrique; Starkl, Markus; Ghangrekar, Makarand; Philip, Ligy

2018-01-01

Moving bed biofilm reactor (MBBR) is a highly effective biological treatment process applied to treat both urban and industrial wastewaters in developing countries. The present study investigated the technical performance of ten full-scale MBBR systems located across India. The biochemical oxygen demand, chemical oxygen demand, total suspended solid, pathogens, and nutrient removal efficiencies were low as compared to the values claimed in literature. Plant 1 was considered for evaluation of environmental impacts using life cycle assessment approach. CML 2 baseline 2000 methodology was adopted, in which 11 impact categories were considered. The life cycle impact assessment results revealed that the main environmental hot spot of this system was energy consumption. Additionally, two scenarios were compared: scenario 1 (direct discharge of treated effluent, i.e., no reuse) and scenario 2 (effluent reuse and tap water replacement). The results showed that scenario 2 significantly reduce the environmental impact in all the categories ultimately decreasing the environmental burden. Moreover, significant economic and environmental benefits can be obtained in scenario 2 by replacing the freshwater demand for non-potable uses. To enhance the performance of wastewater treatment plant (WWTP), there is a need to optimize energy consumption and increase wastewater collection efficiency to maximize the operating capacity of plant and minimize overall environmental footprint. It was concluded that MBBR can be a good alternative for upgrading and optimizing existing municipal wastewater treatment plants with appropriate tertiary treatment. Graphical abstract ᅟ.

Efficacy of a low-dose oral contraceptive containing 20 microg of ethinyl estradiol and 100 microg of levonorgestrel for the treatment of moderate acne: A randomized, placebo-controlled trial.

PubMed

Leyden, James; Shalita, Alan; Hordinsky, Maria; Swinyer, Leonard; Stanczyk, Frank Z; Weber, Margaret E

2002-09-01

Acne is a multifactorial disease in which androgens appear to play an important role. A low-dose oral contraceptive containing 20 microg of ethinyl estradiol and 100 microg of levonorgestrel (EE/LNG) has been shown to improve biochemical markers of androgenicity. Lowering bioavailable androgens may improve acne. The aim of this study was to evaluate the efficacy and safety of a low-dose oral contraceptive containing 20 microg of EE and 100 microg of LNG for the treatment of moderate acne. In a randomized, double-blind, placebo-controlled clinical trial, healthy female subjects (n = 371; >/=14 years old) with regular menstrual cycles and moderate facial acne were randomly assigned to receive EE/LNG or placebo for 6 cycles of 28 days. Acne lesion counts and clinician global assessment were performed at the end of each cycle. Patient self-assessments were collected and biochemical markers of androgenicity were also measured. At the end of the study, the number of inflammatory and total lesions was significantly lower with EE/LNG compared with placebo (P <.05). Patients in the EE/LNG group also had significantly better scores for clinician global and patient self-assessments than those in the placebo group (P <.05). Biochemical markers of androgenicity improved during EE/LNG treatment compared with placebo and baseline values. A low-dose oral contraceptive containing EE/LNG is effective and safe for the treatment of moderate acne.

Cycling to work in London and inhaled dose of black carbon.

PubMed

Nwokoro, Chinedu; Ewin, Clare; Harrison, Clare; Ibrahim, Mubin; Dundas, Isobel; Dickson, Iain; Mushtaq, Naseem; Grigg, Jonathan

2012-11-01

Modelling studies suggest that urban cycling is associated with an increased inhaled dose of fossil fuel-derived black carbon (BC). Using the amount of black material in airway macrophages as a marker of long-term inhaled BC, we sought to compare inhaled BC dose in London (UK) cyclists and non-cyclists. Airway macrophage carbon was assessed in 28 (58%) out of 48 healthy adults (14 cyclists and 14 non-cyclists) who attended for induced sputum. Short-term (24 h) exposure to BC was assessed on a representative working day in 27 out of 28 subjects. Serum interleukin (IL)-1β, IL-2, IL-6, IL-8, granulocyte-macrophage colony-stimulating factor and tumour necrosis factor (TNF)-α were assessed in 26 out of the 28 subjects. Cyclists were found to have increased airway macrophage carbon when compared with non-cyclists (mean ± se 1.81 ± 0.21 versus 1.11 ± 0.07 μm(2); p<0.01). Short-term monitoring showed no difference in 24 h BC exposure between the two groups. However, cyclists were exposed to higher concentrations of BC during commuting (p<0.01). Airway macrophage carbon was associated with monitored commute BC (n=28; r=0.47, p<0.05). TNF-α was found to be increased in cyclists (p<0.05), but no other cytokines were increased. Commuting to work by bicycle in London is associated with increased long-term inhaled dose of BC. Whether cycling per se increases inhaled BC dose remains unclear.

Administrative Preparedness Strategies: Expediting Procurement and Contracting Cycle Times During an Emergency.

PubMed

Hurst, David; Sharpe, Sharon; Yeager, Valerie A

We assessed whether administrative preparedness processes that were intended to expedite the acquisition of goods and services during a public health emergency affect estimated procurement and contracting cycle times. We obtained data from 2014-2015 applications to the Hospital Preparedness Program and Public Health Emergency Preparedness (HPP-PHEP) cooperative agreements. We compared the estimated procurement and contracting cycle times of 61 HPP-PHEP awardees that did and did not have certain administrative processes in place. Certain processes, such as statutes allowing for procuring and contracting on the open market, had an effect on reducing the estimated cycle times for obtaining goods and services. Other processes, such as cooperative purchasing agreements, also had an effect on estimated procurement time. For example, awardees with statutes that permitted them to obtain goods and services in the open market had an average procurement cycle time of 6 days; those without such statutes had a cycle time of 17 days ( P = .04). PHEP awardees should consider adopting these or similar processes in an effort to reduce cycle times.

Sustainable nanotechnology decision support system: bridging risk management, sustainable innovation and risk governance

NASA Astrophysics Data System (ADS)

Subramanian, Vrishali; Semenzin, Elena; Hristozov, Danail; Zabeo, Alex; Malsch, Ineke; McAlea, Eamonn; Murphy, Finbarr; Mullins, Martin; van Harmelen, Toon; Ligthart, Tom; Linkov, Igor; Marcomini, Antonio

2016-04-01

The significant uncertainties associated with the (eco)toxicological risks of engineered nanomaterials pose challenges to the development of nano-enabled products toward greatest possible societal benefit. This paper argues for the use of risk governance approaches to manage nanotechnology risks and sustainability, and considers the links between these concepts. Further, seven risk assessment and management criteria relevant to risk governance are defined: (a) life cycle thinking, (b) triple bottom line, (c) inclusion of stakeholders, (d) risk management, (e) benefit-risk assessment, (f) consideration of uncertainty, and (g) adaptive response. These criteria are used to compare five well-developed nanotechnology frameworks: International Risk Governance Council framework, Comprehensive Environmental Assessment, Streaming Life Cycle Risk Assessment, Certifiable Nanospecific Risk Management and Monitoring System and LICARA NanoSCAN. A Sustainable Nanotechnology Decision Support System (SUNDS) is proposed to better address current nanotechnology risk assessment and management needs, and makes. Stakeholder needs were solicited for further SUNDS enhancement through a stakeholder workshop that included representatives from regulatory, industry and insurance sectors. Workshop participants expressed the need for the wider adoption of sustainability assessment methods and tools for designing greener nanomaterials.

DEVELOPMENT OF THE METHOD AND U.S. NORMALIZATION DATABASE FOR LIFE CYCLE IMPACT ASSESSMENT AND SUSTAINABILITY METRICS

EPA Science Inventory

Normalization is an optional step within Life Cycle Impact Assessment (LCIA) that may be used to assist in the interpretation of life cycle inventory data as well as, life cycle impact assessment results. Normalization transforms the magnitude of LCI and LCIA results into relati...

A Comparative Efficacy of Low-Dose Combined Oral Contraceptives Containing Desogestrel and Drospirenone in Premenstrual Symptoms

PubMed Central

Wichianpitaya, Jirath; Taneepanichskul, Surasak

2013-01-01

Objective. To compare the efficacy of low-dose COC containing desogestrel (DSG) with drospirenone (DRSP) in the changes of premenstrual symptoms. Methods. In an open-label randomized controlled trial, 90 women with premenstrual syndrome who required COC were randomly recruited and allocated equally to receive either 6 cycles of 20 micrograms ethinyl estradiol (EE)/150 micrograms DSG (DSG group) or 20 micrograms EE/3 mg DRSP (DRSP group) in 24/4 extended regimen. Analysis of covariance and repeated analysis of variance were used to determine the difference of mean Women's Health Assessment Questionnaire (WHAQ) scores changes between groups, within group, and in premenstrual, menstrual, and postmenstrual phases. Results. Baseline characteristics and WHAQ scores were comparable. At the ends of the 3rd and the 6th cycles, mean WHAQ scores of all the 3 phases in DRSP group showed significant reduction and were significantly lower than those in DSG group. DSG group showed significant reduction in both premenstrual and menstrual phases after the 6th cycle. Adverse effects were comparable in both groups. In conclusion, low-dose COC containing either DSG or DRSP reduced premenstrual symptoms, but the latter showed greater efficacy and earlier reduction. PMID:23577032

Effects of two combined oral contraceptives containing ethinyl estradiol 20 microg combined with either drospirenone or desogestrel on lipids, hemostatic parameters and carbohydrate metabolism.

PubMed

Klipping, Christine; Marr, Joachim

2005-06-01

To compare the effect of ethinyl estradiol 20 microg/drospirenone 3 mg (EE 20 microg/DRSP 3 mg) administered according to a 24/4 regimen with ethinyl estradiol 20 microg/desogestrel 150 microg (EE 20 microg/DSG 150 microg) administered according to the conventional 21/7 regimen on lipid, carbohydrate and hemostatic parameters. In this open-label study, healthy women were randomized to EE 20 microg/DRSP 3 mg or EE 20 microg/DSG 150 microg for seven cycles. Mean differences in high-density lipoprotein (HDL)- and low-density lipoprotein (LDL)-cholesterol levels at cycle 7 compared to baseline were assessed. Secondary variables included changes in other lipid, hemostatic and carbohydrate parameters. Both treatments increased HDL-cholesterol, but decreased LDL-cholesterol by a comparable extent. Although slightly elevated in both groups, blood glucose and C-peptide levels measured during oral glucose tolerance tests were within normal reference ranges at cycle 7. Overall, the differences in lipid, hemostatic or carbohydrate parameters were not significant between the two treatments. EE 20 microg/DRSP 3 mg has a good safety profile comparable with EE 20 microg/DSG 150 microg.

Holistic impact assessment and cost savings of rainwater harvesting at the watershed scale

EPA Science Inventory

We evaluated the impacts of domestic and agricultural rainwater harvesting (RWH) systems in three watersheds within the Albemarle-Pamlico river basin (southeastern U.S.) using life cycle assessment (LCA) and life cycle cost assessment. Life cycle impact assessment (LCIA) categori...

Bioenergy | National Agricultural Library

Science.gov Websites

Skip to main content Home National Agricultural Library United States Department of Agriculture Ag , graphs), Agricultural Products html Data from: Comparative farm-gate life cycle assessment of oilseed registered trademark of Dries Buytaert. NAL Home | USDA.gov | Agricultural Research Service | Plain Language

Concurrent chemoradiotherapy degrades the quality of life of patients with stage II nasopharyngeal carcinoma as compared to radiotherapy

PubMed Central

Pan, Xin-Bin; Huang, Shi-Ting; Chen, Kai-Hua; Jiang, Yan-Ming; Ma, Jia-Lin; Qu, Song; Li, Ling; Chen, Long; Zhu, Xiao-Dong

2017-01-01

The purpose of this study was to compare the quality of life (QoL) of stage II nasopharyngeal carcinoma (NPC) patients treated with radiotherapy (RT) versus concurrent chemoradiotherapy (CCRT). In a cross-sectional study, these patients were treated with RT (n = 55) or CCRT (n = 51) between June 2008 and June 2013. For all subjects, disease-free survival was more than 3 years. QoL was assessed using the European Organization for Research and Treatment of Cancer Quality of Life Questionnaire-Core 30 (EORTC QLQ-C30) questions and the Head and Neck 35 (EORTC QLQ-H&N35) questions. RT had better outcomes than CCRT for global QoL, functional scales, symptom scales of fatigue and insomnia, financial problems, and weight gain. Survivors receiving 1 cycle of concurrent chemotherapy had worse QoL outcomes than survivors receiving 2 cycles of concurrent chemotherapy. Patients receiving 3 cycles of concurrent chemotherapy had the best QoL outcomes. Thus, CCRT adversely affects the QoL of patients with stage II NPC as compared to radiotherapy. PMID:28152511

IVF with planned single-embryo transfer versus IUI with ovarian stimulation in couples with unexplained subfertility: an economic analysis.

PubMed

van Rumste, Minouche M E; Custers, Inge M; van Wely, Madelon; Koks, Carolien A; van Weering, Hans G I; Beckers, Nicole G M; Scheffer, Gabrielle J; Broekmans, Frank J M; Hompes, Peter G A; Mochtar, Monique H; van der Veen, Fulco; Mol, Ben W J

2014-03-01

Couples with unexplained subfertility are often treated with intrauterine insemination (IUI) with ovarian stimulation, which carries the risk of multiple pregnancies. An explorative randomized controlled trial was performed comparing one cycle of IVF with elective single-embryo transfer (eSET) versus three cycles of IUI-ovarian stimulation in couples with unexplained subfertility and a poor prognosis for natural conception, to assess the economic burden of the treatment modalities. The main outcome measures were ongoing pregnancy rates and costs. This study randomly assigned 58 couples to IVF-eSET and 58 couples to IUI-ovarian stimulation. The ongoing pregnancy rates were 24% in with IVF-eSET versus 21% with IUI-ovarian stimulation, with two and three multiple pregnancies, respectively. The mean cost per included couple was significantly different: €2781 with IVF-eSET and €1876 with IUI-ovarian stimulation (P<0.01). The additional costs per ongoing pregnancy were €2456 for IVF-eSET. In couples with unexplained subfertility, one cycle of IVF-eSET cost an additional €900 per couple compared with three cycles of IUI-ovarian stimulation, for no increase in ongoing pregnancy rates or decrease in multiple pregnancies. When IVF-eSET results in higher ongoing pregnancy rates, IVF would be the preferred treatment. Couples that have been trying to conceive unsuccessfully are often treated with intrauterine insemination (IUI) and medication to improve egg production (ovarian stimulation). This treatment carries the risk of multiple pregnancies like twins. We performed an explorative study among those couples that had a poor prognosis for natural conception. One cycle of IVF with transfer of one selected embryo (elective single-embryo transfer, eSET) was compared with three cycles of IUI-ovarian stimulation. The aim of this study was to assess the economic burden of both treatments. The Main outcome measures were number of good pregnancies above 12weeks and costs. We randomly assigned 58 couples to IVF-eSET and 58 couples to IUI-ovarian stimulation. The ongoing pregnancy rates were comparable: 24% with IVF-eSET versus 21% with IUI-ovarian stimulation. There were two multiple pregnancies with IVF-eSET and three multiple pregnancies with IUI-ovarian stimulation. The mean cost per included couple was significantly different, €2781 with IVF-eSET and €1876 with IUI-ovarian stimulation. The additional costs per ongoing pregnancy were €2456 for IVF-eSET. In couples with unexplained subfertility, one cycle of IVF-eSET costed an additional €900 per couple compared to three cycles of IUI-ovarian stimulation, for no increase in ongoing pregnancy rates or decrease in multiple pregnancies. We conclude that IUI-ovarian stimulation is the preferred treatment to start with. When IVF-eSET results in a higher ongoing pregnancy rate (>38%), IVF would be the preferred treatment. Copyright © 2013 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Life cycle assessment on microalgal biodiesel production using a hybrid cultivation system.

PubMed

Adesanya, Victoria O; Cadena, Erasmo; Scott, Stuart A; Smith, Alison G

2014-07-01

A life cycle assessment (LCA) was performed on a putative biodiesel production plant in which the freshwater alga Chlorella vulgaris, was grown using an existing system similar to a published commercial-scale hybrid cultivation. The hybrid system couples airlift tubular photobioreactors with raceway ponds in a two-stage process for high biomass growth and lipid accumulation. The results show that microalgal biodiesel production would have a significantly lower environmental impact than fossil-derived diesel. Based on the functional unit of 1 ton of biodiesel produced, the hybrid cultivation system and hypothetical downstream process (base case) would have 42% and 38% savings in global warming potential (GWP) and fossil-energy requirements (FER) when compared to fossil-derived diesel, respectively. Sensitivity analysis was performed to identify the most influential process parameters on the LCA results. The maximum reduction in GWP and FER was observed under mixotrophic growth conditions with savings of 76% and 75% when compared to conventional diesel, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Environmental performances of coproducts. Application of Claiming-Based Allocation models to straw and vetiver biorefineries in an Indian context.

PubMed

Gnansounou, Edgard; Raman, Jegannathan Kenthorai

2018-04-24

Among the renewables, non-food and wastelands based biofuels are essential for the transport sector to achieve country's climate mitigation targets. With the growing interest in biorefineries, setting policy requirements for other coproducts along with biofuels is necessary to improve the products portfolio of biorefinery, increase the bioproducts perception by the consumers and push the technology forward. Towards this context, Claiming-Based allocation models were used in comparative life cycle assessment of multiple products from wheat straw biorefinery and vetiver biorefinery. Vetiver biorefinery shows promising Greenhouse gas emission savings (181-213%) compared to the common crop based lignocellulose (wheat straw) biorefinery. Assistance of Claiming-Based Allocation models favors to find out the affordable allocation limit (0-80%) among the coproducts in order to achieve the individual prospective policy targets. Such models show promising application in multiproduct life cycle assessment studies where appropriate allocation is challenging to achieve the individual products emission subject to policy targets. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparative cradle-to-grave life cycle assessment of biogas production from marine algae and cattle manure biorefineries.

PubMed

Giwa, Adewale

2017-11-01

The environmental impacts resulting from the cradle-to-grave life cycles of Enteromorpha prolifera macroalgae and cattle manure biorefineries are assessed and compared. Sensitivity analysis is carried out to evaluate the response of the impacts to changes in biogas application by using Simapro 7.3.3. Three scenarios are considered in the biorefineries. In the first and second scenarios, the biogas produced is considered to be used for electricity production and transportation, respectively. In the third scenario, the biogas is considered to be recycled back to the systems. Process energy requirements and transportation of inputs contribute the largest share of the overall impacts. The cattle manure biorefinery is slightly more eco-friendly than the macroalgae biorefinery in Scenarios 1 and 2 because it requires more eco-friendly inputs. However, the macroalgae biorefinery becomes more eco-friendly than the cattle manure biorefinery in Scenario 3 because macroalgae require less energy and water for biogas production. Copyright © 2017 Elsevier Ltd. All rights reserved.

A case study by life cycle assessment

NASA Astrophysics Data System (ADS)

Li, Shuyun

2017-05-01

This article aims to assess the potential environmental impact of an electrical grinder during its life cycle. The Life Cycle Inventory Analysis was conducted based on the Simplified Life Cycle Assessment (SLCA) Drivers that calculated from the Valuation of Social Cost and Simplified Life Cycle Assessment Model (VSSM). The detailed results for LCI can be found under Appendix II. The Life Cycle Impact Assessment was performed based on Eco-indicator 99 method. The analysis results indicated that the major contributor to the environmental impact as it accounts for over 60% overall SLCA output. In which, 60% of the emission resulted from the logistic required for the maintenance activities. This was measured by conducting the hotspot analysis. After performing sensitivity analysis, it is evidenced that changing fuel type results in significant decrease environmental footprint. The environmental benefit can also be seen from the negative output values of the recycling activities. By conducting Life Cycle Assessment analysis, the potential environmental impact of the electrical grinder was investigated.

Improved Environmental Life Cycle Assessment of Crop Production at the Catchment Scale via a Process-Based Nitrogen Simulation Model.

PubMed

Liao, Wenjie; van der Werf, Hayo M G; Salmon-Monviola, Jordy

2015-09-15

One of the major challenges in environmental life cycle assessment (LCA) of crop production is the nonlinearity between nitrogen (N) fertilizer inputs and on-site N emissions resulting from complex biogeochemical processes. A few studies have addressed this nonlinearity by combining process-based N simulation models with LCA, but none accounted for nitrate (NO3(-)) flows across fields. In this study, we present a new method, TNT2-LCA, that couples the topography-based simulation of nitrogen transfer and transformation (TNT2) model with LCA, and compare the new method with a current LCA method based on a French life cycle inventory database. Application of the two methods to a case study of crop production in a catchment in France showed that, compared to the current method, TNT2-LCA allows delineation of more appropriate temporal limits when developing data for on-site N emissions associated with specific crops in this catchment. It also improves estimates of NO3(-) emissions by better consideration of agricultural practices, soil-climatic conditions, and spatial interactions of NO3(-) flows across fields, and by providing predicted crop yield. The new method presented in this study provides improved LCA of crop production at the catchment scale.

Life cycle assessment of EPS and CPB inserts: design considerations and end of life scenarios.

PubMed

Tan, Reginald B H; Khoo, Hsien H

2005-02-01

Expanded polystyrene (EPS) and corrugated paperboard (CPB) are used in many industrial applications, such as containers, shock absorbers or simply as inserts. Both materials pose two different types of environmental problems. The first is the pollution and resource consumption that occur during the production of these materials; the second is the growing landfills that arise out of the excessive disposal of these packaging materials. Life cycle assessment or LCA will be introduced in this paper as a useful tool to compare the environmental performance of both EPS and CPB throughout their life cycle stages. This paper is divided into two main parts. The first part investigates the environmental impacts of the production of EPS and CPB from 'cradle-to-gate', comparing two inserts--both the original and proposed new designs. In the second part, LCA is applied to investigate various end-of-life cases for the same materials. The study will evaluate the environmental impacts of the present waste management practices in Singapore. Several 'what-if' cases are also discussed, including various percentages of landfilling and incineration. The SimaPro LCA Version 5.0 software's Eco-indicator 99 method is used to investigate the following five environmental impact categories: climate change, acidification/eutrophication, ecotoxicity, fossil fuels and respiratory inorganics.

Disruption of the Glutamate–Glutamine Cycle Involving Astrocytes in an Animal Model of Depression for Males and Females

PubMed Central

Rappeneau, Virginie; Blaker, Amanda; Petro, Jeff R.; Yamamoto, Bryan K.; Shimamoto, Akiko

2016-01-01

Background: Women are twice as likely as men to develop major depression. The brain mechanisms underlying this sex disparity are not clear. Disruption of the glutamate–glutamine cycle has been implicated in psychiatric disturbances. This study identifies sex-based impairments in the glutamate–glutamine cycle involving astrocytes using an animal model of depression. Methods: Male and female adult Long-Evans rats were exposed to chronic social defeat stress (CSDS) for 21 days, using a modified resident-intruder paradigm. Territorial aggression was used for males and maternal aggression was used for females to induce depressive-like deficits for intruders. The depressive-like phenotype was assessed with intake for saccharin solution, weight gain, estrous cycle, and corticosterone (CORT). Behaviors displayed by the intruders during daily encounters with residents were characterized. Rats with daily handling were used as controls for each sex. Ten days after the last encounter, both the intruders and controls were subjected to a no-net-flux in vivo microdialysis to assess glutamate accumulation and extracellular glutamine in the nucleus accumbens (NAc). The contralateral hemispheres were used for determining changes in astrocytic markers, including glial fibrillary acidic protein (GFAP) and glutamate transporter-1 (GLT-1). Results: Both male and female intruders reduced saccharin intake over the course of CSDS, compared to their pre-stress period and to their respective controls. Male intruders exhibited submissive/defensive behaviors to territorial aggression by receiving sideways threats and bites. These males showed reductions in striatal GLT-1 and spontaneous glutamine in the NAc, compared to controls. Female intruders exhibited isolated behaviors to maternal aggression, including immobility, rearing, and selfgrooming. Their non-reproductive days were extended. Also, they showed reductions in prefrontal and accumbal GFAP+ cells and prefrontal GLT-1, compared to controls. When 10 μM of glutamate was infused, these females showed a significant accumulation of glutamate compared to controls. Infusions of glutamate reduced extracellular glutamine for both male and female intruders compared to their respective controls. Conclusion: Twenty-one days of territorial or maternal aggression produced a depressive-like phenotype and impaired astrocytes in both male and female intruders. Disruption of the glutamate–glutamine cycle in the PFC-striatal network may be linked to depressive-like deficits more in females than in males. PMID:28018190

Considering time in LCA: dynamic LCA and its application to global warming impact assessments.

PubMed

Levasseur, Annie; Lesage, Pascal; Margni, Manuele; Deschênes, Louise; Samson, Réjean

2010-04-15

The lack of temporal information is an important limitation of life cycle assessment (LCA). A dynamic LCA approach is proposed to improve the accuracy of LCA by addressing the inconsistency of temporal assessment. This approach consists of first computing a dynamic life cycle inventory (LCI), considering the temporal profile of emissions. Then, time-dependent characterization factors are calculated to assess the dynamic LCI in real-time impact scores for any given time horizon. Although generally applicable to any impact category, this approach is developed here for global warming, based on the radiative forcing concept. This case study demonstrates that the use of global warming potentials for a given time horizon to characterize greenhouse gas emissions leads to an inconsistency between the time frame chosen for the analysis and the time period covered by the LCA results. Dynamic LCA is applied to the US EPA LCA on renewable fuels, which compares the life cycle greenhouse gas emissions of different biofuels with fossil fuels including land-use change emissions. The comparison of the results obtained with both traditional and dynamic LCA approaches shows that the difference can be important enough to change the conclusions on whether or not a biofuel meets some given global warming reduction targets.

HRV Analysis to Identify Stages of Home-based Telerehabilitation Exercise.

PubMed

Jeong, In Cheol; Finkelstein, Joseph

2014-01-01

Spectral analysis of heart rate variability (HRV) has been widely used to investigate activity of autonomous nervous system. Previous studies demonstrated potential of analysis of short-term sequences of heart rate data in a time domain for continuous monitoring of levels of physiological stress however the value of HRV parameters in frequency domain for monitoring cycling exercise has not been established. The goal of this study was to assess whether HRV parameters in frequency domain differ depending on a stage of cycling exercise. We compared major HRV parameters in high, low and very low frequency ranges during rest, height of exercise, and recovery during cycling exercise. Our results indicated responsiveness of frequency-domain indices to different phases of cycling exercise program and their potential in monitoring autonomic balance and stress levels as a part of a tailored home-based telerehabilitation program.

Approach to proliferation risk assessment based on multiple objective analysis framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrianov, A.; Kuptsov, I.; Studgorodok 1, Obninsk, Kaluga region, 249030

2013-07-01

The approach to the assessment of proliferation risk using the methods of multi-criteria decision making and multi-objective optimization is presented. The approach allows the taking into account of the specifics features of the national nuclear infrastructure, and possible proliferation strategies (motivations, intentions, and capabilities). 3 examples of applying the approach are shown. First, the approach has been used to evaluate the attractiveness of HEU (high enriched uranium)production scenarios at a clandestine enrichment facility using centrifuge enrichment technology. Secondly, the approach has been applied to assess the attractiveness of scenarios for undeclared production of plutonium or HEU by theft of materialsmore » circulating in nuclear fuel cycle facilities and thermal reactors. Thirdly, the approach has been used to perform a comparative analysis of the structures of developing nuclear power systems based on different types of nuclear fuel cycles, the analysis being based on indicators of proliferation risk.« less

Illustrating anticipatory life cycle assessment for emerging photovoltaic technologies.

PubMed

Wender, Ben A; Foley, Rider W; Prado-Lopez, Valentina; Ravikumar, Dwarakanath; Eisenberg, Daniel A; Hottle, Troy A; Sadowski, Jathan; Flanagan, William P; Fisher, Angela; Laurin, Lise; Bates, Matthew E; Linkov, Igor; Seager, Thomas P; Fraser, Matthew P; Guston, David H

2014-09-16

Current research policy and strategy documents recommend applying life cycle assessment (LCA) early in research and development (R&D) to guide emerging technologies toward decreased environmental burden. However, existing LCA practices are ill-suited to support these recommendations. Barriers related to data availability, rapid technology change, and isolation of environmental from technical research inhibit application of LCA to developing technologies. Overcoming these challenges requires methodological advances that help identify environmental opportunities prior to large R&D investments. Such an anticipatory approach to LCA requires synthesis of social, environmental, and technical knowledge beyond the capabilities of current practices. This paper introduces a novel framework for anticipatory LCA that incorporates technology forecasting, risk research, social engagement, and comparative impact assessment, then applies this framework to photovoltaic (PV) technologies. These examples illustrate the potential for anticipatory LCA to prioritize research questions and help guide environmentally responsible innovation of emerging technologies.

Evaluating Indicators and Life Cycle Inventories for Processes in Early Stages of Technical Readiness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Eric C; Smith, Raymond; Ruiz-Mercado, Gerardo

This presentation examines different methods for analyzing manufacturing processes in the early stages of technical readiness. Before developers know much detail about their processes, it is valuable to apply various assessments to evaluate their performance. One type of assessment evaluates performance indicators to describe how closely processes approach desirable objectives. Another type of assessment determines the life cycle inventories (LCI) of inputs and outputs for processes, where for a functional unit of product, the user evaluates the resources used and the releases to the environment. These results can be compared to similar processes or combined with the LCI of othermore » processes to examine up-and down-stream chemicals. The inventory also provides a listing of the up-stream chemicals, which permits study of the whole life cycle. Performance indicators are evaluated in this presentation with the U.S. Environmental Protection Agency's GREENSCOPE (Gauging Reaction Effectiveness for ENvironmental Sustainability with a multi-Objective Process Evaluator) methodology, which evaluates processes in four areas: Environment, Energy, Economics, and Efficiency. The method develops relative scores for indicators that allow comparisons across various technologies. In this contribution, two conversion pathways for producing cellulosic ethanol from biomass, via thermochemical and biochemical routes, are studied. The information developed from the indicators and LCI can be used to inform the process design and the potential life cycle effects of up- and down-stream chemicals.« less

Evaluating the Safety Profile of Non-Active Implantable Medical Devices Compared with Medicines.

PubMed

Pane, Josep; Coloma, Preciosa M; Verhamme, Katia M C; Sturkenboom, Miriam C J M; Rebollo, Irene

2017-01-01

Recent safety issues involving non-active implantable medical devices (NAIMDs) have highlighted the need for better pre-market and post-market evaluation. Some stakeholders have argued that certain features of medicine safety evaluation should also be applied to medical devices. Our objectives were to compare the current processes and methodologies for the assessment of NAIMD safety profiles with those for medicines, identify potential gaps, and make recommendations for the adoption of new methodologies for the ongoing benefit-risk monitoring of these devices throughout their entire life cycle. A literature review served to examine the current tools for the safety evaluation of NAIMDs and those for medicines. We searched MEDLINE using these two categories. We supplemented this search with Google searches using the same key terms used in the MEDLINE search. Using a comparative approach, we summarized the new product design, development cycle (preclinical and clinical phases), and post-market phases for NAIMDs and drugs. We also evaluated and compared the respective processes to integrate and assess safety data during the life cycle of the products, including signal detection, signal management, and subsequent potential regulatory actions. The search identified a gap in NAIMD safety signal generation: no global program exists that collects and analyzes adverse events and product quality issues. Data sources in real-world settings, such as electronic health records, need to be effectively identified and explored as additional sources of safety information, particularly in some areas such as the EU and USA where there are plans to implement the unique device identifier (UDI). The UDI and other initiatives will enable more robust follow-up and assessment of long-term patient outcomes. The safety evaluation system for NAIMDs differs in many ways from those for drugs, but both systems face analogous challenges with respect to monitoring real-world usage. Certain features of the drug safety evaluation process could, if adopted and adapted for NAIMDs, lead to better and more systematic evaluations of the latter.

Effect of soil in nutrient cycle assessment at dairy farms

NASA Astrophysics Data System (ADS)

van Leeuwen, Maricke; de Boer, Imke; van Dam, Jos; van Middelaar, Corina; Stoof, Cathelijne

2016-04-01

Annual farm nutrient cycle assessments give valuable insight in the nutrient cycles and nutrient losses at dairy farms. It describes nutrient use efficiencies for the entire farm and for the underlying components cattle, manure, crops and soil. In many modelling studies, soil is kept as a constant factor, while soil quality is vital for soil functioning of the ecosystem. Improving soil quality will improve the nutrient cycle, and will also have positive effect on the soil functions crop production, water cycling and greenhouse gas mitigation. Spatial variation of soil properties within a farm, however, are not included in annual nutrient cycle assessments. Therefore it is impossible to identify fields where most profit can be gained by improving farm management at field level, and it is not possible to identify and to quantify nutrient flow path ways. The aim of this study is to develop a framework to improve the annual nutrient cycle assessment at Dutch dairy farms, by including soil properties and their spatial variation within farms. Soil type and soil quality will be described by visual soil assessment of soil quality characteristics. The visual observations will be linked to the nutrient cycle assessment, using soil-hydrological model SWAP. We will demonstrate how soil quality at field level can impact on crop production, eutrophication potential and greenhouse gas potential at farm level. Also, we will show how this framework can be used by farmers to improve their farm management. This new approach is focusing on annual nutrient cycle assessment, but could also be used in life cycle assessment. It will improve understanding of soil functioning and dairy farm management.

A Life Cycle Assessment Case Study of Coal-Fired Electricity Generation with Humidity Swing Direct Air Capture of CO2 versus MEA-Based Postcombustion Capture.

PubMed

van der Giesen, Coen; Meinrenken, Christoph J; Kleijn, René; Sprecher, Benjamin; Lackner, Klaus S; Kramer, Gert Jan

2017-01-17

Most carbon capture and storage (CCS) envisions capturing CO 2 from flue gas. Direct air capture (DAC) of CO 2 has hitherto been deemed unviable because of the higher energy associated with capture at low atmospheric concentrations. We present a Life Cycle Assessment of coal-fired electricity generation that compares monoethanolamine (MEA)-based postcombustion capture (PCC) of CO 2 with distributed, humidity-swing-based direct air capture (HS-DAC). Given suitable temperature, humidity, wind, and water availability, HS-DAC can be largely passive. Comparing energy requirements of HS-DAC and MEA-PCC, we find that the parasitic load of HS-DAC is less than twice that of MEA-PCC (60-72 kJ/mol versus 33-46 kJ/mol, respectively). We also compare other environmental impacts as a function of net greenhouse gas (GHG) mitigation: To achieve the same 73% mitigation as MEA-PCC, HS-DAC would increase nine other environmental impacts by on average 38%, whereas MEA-PCC would increase them by 31%. Powering distributed HS-DAC with photovoltaics (instead of coal) while including recapture of all background GHG, reduces this increase to 18%, hypothetically enabling coal-based electricity with net-zero life-cycle GHG. We conclude that, in suitable geographies, HS-DAC can complement MEA-PCC to enable CO 2 capture independent of time and location of emissions and recapture background GHG from fossil-based electricity beyond flue stack emissions.

Serum bioactive and immunoreactive luteinizing hormone and follicle-stimulating hormone levels in women with cycle abnormalities, with or without polycystic ovarian disease.

PubMed

Fauser, B C; Pache, T D; Lamberts, S W; Hop, W C; de Jong, F H; Dahl, K D

1991-10-01

Serum steroid, gonadotropin, and alpha-subunit levels were assessed in 35 women with cycle abnormalities [11 with and 24 without polycystic ovarian disease (PCOD) according to strict clinical and biochemical criteria] and 8 regularly cycling women in the early (cycle day 3 or 4) and mid (cycle day 7 or 8) follicular phase. LH and FSH levels were estimated using two immunological techniques [RIA and immunoradiometric assay (IRMA)] and in vitro bioassays (BIO), using mouse Leydig cells and rat granulosa cells, respectively. In PCOD patients mean alpha-subunit, free androgen index [FAI; testosterone x 100/sex hormone-binding globulin (SHBG)], androstenedione, estrone, and estradiol (E2) were significantly elevated compared to levels in the early follicular phase of control cycles and non-PCOD patients. In addition, in PCOD patients mean IRMA-LH and RIA-LH levels were distinctly increased (2.8- to 3.6 fold, respectively; both comparisons, P less than 0.001) compared to control values, but in the same order of magnitude (1.3- to 1.4-fold increments) as that in non-PCOD patients. However, the median BIO-LH level in PCOD patients was 5.9-fold higher than that in non-PCOD patients and 4.0-fold higher than the BIO-LH in the early follicular phase of control women. Consequently, the median BIO/IRMA-LH ratio was 4.8-fold higher in PCOD patients compared to non-PCOD patients. In women with cycle abnormalities, individual BIO/IRMA-LH ratios correlated with BIO-LH (rs = 0.48), FAI (rs = 0.39), free estrogens (E2/SHBG ratios; rs = 0 0.47), and dehydroepiandrosterone sulfate (rs = 0.60) concentrations. Mean IRMA-, RIA-, and BIO-FSH levels and BIO/IRMA-FSH ratios were not significantly different when various groups were compared. Although RIA- and IRMA-LH levels showed good correlation (rs = 0.88), RIA-LH levels were consistently higher, resulting in distinctly higher RIA-LH/FSH ratios (mean, 4.5) compared to IRMA-LH/FSH ratios (median, 1.8) in PCOD patients.(ABSTRACT TRUNCATED AT 400 WORDS)

Impact on hepatic estrogen-sensitive proteins by a 1-year contraceptive vaginal ring delivering Nestorone® and ethinyl estradiol.

PubMed

Archer, D F; Thomas, M A; Conard, J; Merkatz, R B; Creasy, G W; Roberts, K; Plagianos, M; Blithe, D; Sitruk-Ware, R

2016-01-01

Estrogen-sensitive hepatic proteins were assessed in women using a contraceptive vaginal ring (CVR) delivering 150mcg Nestorone® (NES) and 15mcg ethinyl estradiol (EE). A substudy of the Contraceptive Clinical Trials Network of the National Institute of Child Health and Human Development enrolled 129 participants, with assessments of factor VIII, fibrinogen, protein S (PS) and sex hormone binding globulin (SHBG). Thirty-six participants had used combined hormonal contraceptives (CHCs) in the cycle preceding first CVR use (recent users) and 70 had no history of recent use (nonusers). Mean values at baseline were within the normal range for all four proteins but were higher for factor VIII, fibrinogen and SHBG and significantly lower for PS in recent compared to nonusers. During NES/EE CVR use, factor VIII, fibrinogen and PS were within the normal range; however, SHBG levels were increased by nearly 100% at Cycle 13. The change from baseline to final evaluation was statistically significant for all proteins in nonusers. The change in recent users was significant for factor VIII at Cycle 6 and for SHBG at Cycles 6 and 13, but not for PS or fibrinogen. NES/EE CVR for up to 13cycles was associated with changes from baseline in plasma levels of factor VIII, fibrinogen and PS that were within the normal range, with SHBG levels above the normal range by Cycle 6. Nonusers of CHC before CVR showed wider changes in values versus recent users whose baseline values were increased by previous EE exposure. Recent use of CHCs demonstrated significant changes in all four measured hepatic proteins at baseline compared to nonusers. Use of the NES/EE CVR further changed these hepatic protein markers, but values remained within the normal range. Prebaseline exposure to estrogen can obscure interpretation of hepatic proteins changes associated with a second CHC. Copyright © 2016 Elsevier Inc. All rights reserved.

Use of unbalanced laminates as a screening method for microcracking

NASA Technical Reports Server (NTRS)

Papadopoulos, Demetrios S.; Bowles, Kenneth J.

1990-01-01

State-of-the-art, high temperature polyimide matrix composites, reinforced with continuous graphite fibers are known to be susceptible to intraply cracking when thermally cycled over their useful service temperature range. It is believed that the transply cracking, in part, results from residual stresses caused by differences in coefficients of thermal expansion (CTE) between the polymer matrix and the reinforcement. Thermal cycling tests to investigate this phenomenon involve expensive time and energy consuming programs which are not economically feasible for use as a part of a materials screening process. As an alternative to thermal cycling studies, a study of unbalanced crossply graphite fiber reinforcement composites was conducted to assess the effect of the composite ply layup and surface condition on the residual stresses that remain after the processing of these materials. The residual stresses were assessed by measuring the radii of curvature of the types of laminates that were studied. The temperature at which stress-free conditions existed were determined and a dye penetrant method was used to observe surface damage resulting from excessive residual stress buildup. These results are compared with some published results of thermal cycling tests that were previously conducted on balanced polyimide composites.

Hemodynamic and psychological responses to laboratory stressors in women: Assessing the roles of menstrual cycle phase, premenstrual symptomatology, and sleep characteristics

PubMed Central

Lustyk, M. Kathleen B.; Douglas, Haley A.C.; Shilling, Elizabeth A.; Woods, Nancy F.

2016-01-01

This study assessed whether premenstrual symptomatology and/or sleep characteristics explain increased luteal phase psychophysiological reactivity to laboratory stressors. We hypothesized that: (1) premenstrual symptoms and sleep characteristics would explain greater luteal versus follicular phase psychophysiological reactivity, (2) symptoms and sleep characteristics would differentially predict psychophysiological reactivity within each cycle phase, and (3) symptoms and sleep characteristics would interact to affect luteal but not follicular reactivity. Freely cycling women (N=87) completed two laboratory sessions, one follicular (cycle days 5–9) and one luteal (days 7–10 post-ovulation). We employed two stressors: one physical (cold pressor task) and the other cognitive in nature (Paced Auditory Serial Addition Task). During testing, electrocardiography monitored heart rate (HR) while a timed and auto-inflatable sphygmomanometer assessed blood pressure (BP). Participants also completed a one-time self-report measure of sleep characteristics and premenstrual symptomatology as well as a measure of state anxiety pre-post stressor. Results revealed greater luteal HR and systolic BP reactivity compared to follicular reactivity (p<0.001 for both analyses), however neither premenstrual symptoms nor sleep characteristics explained this luteal increase. Within cycle analyses revealed that symptoms and sleep characteristics interacted to affect luteal phase state anxiety reactivity (R2=.32, p=.002) with negative affect being associated with more reactivity when sleep hours were low (β=.333, p=.04). Overall, significant relationships existed during the luteal phase only. Findings are discussed in terms of clinical utility and methodological challenges related to performing laboratory stress testing in women. PMID:23092740

Evaluation of Functional Electrical Stimulation to Assist Cycling in Four Adolescents with Spastic Cerebral Palsy

PubMed Central

Harrington, Ann Tokay; McRae, Calum G. A.; Lee, Samuel C. K.

2012-01-01

Introduction. Adolescents with cerebral palsy (CP) often have difficulty participating in exercise at intensities necessary to improve cardiovascular fitness. Functional electrical stimulation- (FES-) assisted cycling is proposed as a form of exercise for adolescents with CP. The aims of this paper were to adapt methods and assess the feasibility of applying FES cycling technology in adolescents with CP, determine methods of performing cycling tests in adolescents with CP, and evaluate the immediate effects of FES assistance on cycling performance. Materials/Methods. Four participants (12–14 years old; GMFCS levels III-IV) participated in a case-based pilot study of FES-assisted cycling in which bilateral quadriceps muscles were activated using surface electrodes. Cycling cadence, power output, and heart rate were collected. Results. FES-assisted cycling was well tolerated (n = 4) and cases are presented demonstrating increased cadence (2–43 rpm), power output (19–70%), and heart rates (4-5%) and decreased variability (8–13%) in cycling performance when FES was applied, compared to volitional cycling without FES assistance. Some participants (n = 2) required the use of an auxiliary hub motor for assistance. Conclusions. FES-assisted cycling is feasible for individuals with CP and may lead to immediate improvements in cycling performance. Future work will examine the potential for long-term fitness gains using this intervention. PMID:22685479

Comparative Life Cycle Assessment and Cost Analysis of Bath Wastewater Treatment Plant Upgrades - slides

EPA Science Inventory

Many municipalities are facing the call to increase nutrient removal performance of their wastewater treatment plants in order to limit the impacts of eutrophication on the receiving waterbodies. The associated upgrades often demand investment in new technologies and increases in...

Comparison of the influence of age on cycling efficiency and the energy cost of running in well-trained triathletes.

PubMed

Peiffer, Jeremiah; Abbiss, Chris R; Sultana, Frederic; Bernard, Thierry; Brisswalter, Jeanick

2016-01-01

Locomotive efficiency is cited as an important component to endurance performance; however, inconsistent observations of age-related changes in efficiency question its influence in the performance of masters athletes. This study examined locomotive efficiency in young and masters triathletes during both a run and cycle test. Twenty young (28.5 ± 2.6 years) and 20 masters (59.8 ± 1.3 years) triathletes completed an incremental cycling and running test to determine maximal aerobic consumption (VO2max) and the first ventilatory threshold (VT1). Participants then completed 10-min submaximal running and cycling tests at VT1 during which locomotive efficiency was calculated from expired ventilation. Additionally, body fat percentage was determined using skin-fold assessment. During the cycle and run, VO2max was lower in the masters (48.3 ± 5.4 and 49.6 ± 4.8 ml kg(-1) min(-1), respectively) compared with young (61.6 ± 5.7 and 62.4 ± 5.2 ml kg(-1) min(-1), respectively) cohort. Maximal running speed and the cycling power output corresponding to VO2max were also lower in the masters (15.1 ± 0.8 km h(-1) and 318.6 ± 26.0 W) compared with the young (19.5 ± 1.3 km h(-1) and 383.6 ± 35.0 W) cohort. Cycling efficiency was lower (-11.2%) in the masters compared with young cohort. Similar results were observed for the energy cost of running (+10.8%); however, when scaled to lean body mass, changes were more pronounced during the run (+22.1%). Within trained triathletes, ageing can influence efficiency in both the run and cycle discipline. While disregarded in the past, efficiency should be considered in research examining performance in ageing athletes.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be; Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be; Braet, Johan, E-mail: johan.braet@uantwerpen.be

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages,more » e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.« less

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments

NASA Astrophysics Data System (ADS)

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-01

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO2 (GWPbio). In this study we calculated the GWPbio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWPbio factors ranged from 0.13-0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWPbio. Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWPbio and energy conversion efficiency. By considering the GWPbio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWPbio.

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments

PubMed Central

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-01

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO2 (GWPbio). In this study we calculated the GWPbio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWPbio factors ranged from 0.13–0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWPbio. Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWPbio and energy conversion efficiency. By considering the GWPbio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWPbio. PMID:28045111

Analysis of the Global Warming Potential of Biogenic CO2 Emission in Life Cycle Assessments.

PubMed

Liu, Weiguo; Zhang, Zhonghui; Xie, Xinfeng; Yu, Zhen; von Gadow, Klaus; Xu, Junming; Zhao, Shanshan; Yang, Yuchun

2017-01-03

Biomass is generally believed to be carbon neutral. However, recent studies have challenged the carbon neutrality hypothesis by introducing metric indicators to assess the global warming potential of biogenic CO 2 (GWP bio ). In this study we calculated the GWP bio factors using a forest growth model and radiative forcing effects with a time horizon of 100 years and applied the factors to five life cycle assessment (LCA) case studies of bioproducts. The forest carbon change was also accounted for in the LCA studies. GWP bio factors ranged from 0.13-0.32, indicating that biomass could be an attractive energy resource when compared with fossil fuels. As expected, short rotation and fast-growing biomass plantations produced low GWP bio . Long-lived wood products also allowed more regrowth of biomass to be accounted as absorption of the CO 2 emission from biomass combustion. The LCA case studies showed that the total life cycle GHG emissions were closely related to GWP bio and energy conversion efficiency. By considering the GWP bio factors and the forest carbon change, the production of ethanol and bio-power appeared to have higher GHG emissions than petroleum-derived diesel at the highest GWP bio .

Analysis and performance assessment of a new solar-based multigeneration system integrated with ammonia fuel cell and solid oxide fuel cell-gas turbine combined cycle

NASA Astrophysics Data System (ADS)

Siddiqui, Osamah; Dincer, Ibrahim

2017-12-01

In the present study, a new solar-based multigeneration system integrated with an ammonia fuel cell and solid oxide fuel cell-gas turbine combined cycle to produce electricity, hydrogen, cooling and hot water is developed for analysis and performance assessment. In this regard, thermodynamic analyses and modeling through both energy and exergy approaches are employed to assess and evaluate the overall system performance. Various parametric studies are conducted to study the effects of varying system parameters and operating conditions on the energy and exergy efficiencies. The results of this study show that the overall multigeneration system energy efficiency is obtained as 39.1% while the overall system exergy efficiency is calculated as 38.7%, respectively. The performance of this multigeneration system results in an increase of 19.3% in energy efficiency as compared to single generation system. Furthermore, the exergy efficiency of the multigeneration system is 17.8% higher than the single generation system. Moreover, both energy and exergy efficiencies of the solid oxide fuel cell-gas turbine combined cycle are determined as 68.5% and 55.9% respectively.

An 8-Week Low-Intensity Progressive Cycling Training Improves Motor Functions in Patients with Early-Stage Parkinson's Disease.

PubMed

Chang, Hsiu Chen; Lu, Chin Song; Chiou, Wei Da; Chen, Chiung Chu; Weng, Yi Hsin; Chang, Ya Ju

2018-04-01

The effects of high-intensity cycling as an adjuvant therapy for early-stage Parkinson's disease (PD) were highlighted recently. However, patients experience difficulties in maintaining these cycling training programs. The present study investigated the efficacy of cycling at a mild-to-moderate intensity in early-stage PD. Thirteen PD patients were enrolled for 16 serial cycling sessions over a 2-month period. Motor function was assessed using the Unified Parkinson's Disease Rating Scale part III (UPDRS III) and Timed Up and Go (TUG) test as primary outcomes. The Montreal Cognitive Assessment (MoCA), modified Hoehn and Yahr Stage (mHYS), total UPDRS, Falls Efficacy Scale, New Freezing of Gait Questionnaire, Schwab and England Activities of Daily Living, 39-item Parkinson's Disease Questionnaire, Patient Global Impression of Change, and gait performance were assessed as secondary outcomes. The age and the age at onset were 59.67±7.24 and 53.23±10.26 years (mean±SD), respectively. The cycling cadence was 53.27±8.92 revolutions per minute. The UPDRS III score improved significantly after 8 training sessions (p=0.011) and 16 training sessions (T2) (p=0.001) in the off-state, and at T2 (p=0.004) in the on-state compared to pretraining (T0). The TUG duration was significantly shorter at T2 than at T0 (p<0.05). The findings of MoCA, total UPDRS, double limb support time, and mHYS (in both the off- and on-states) also improved significantly at T2. Our pioneer study has demonstrated that a low-intensity progressive cycling exercise can improve motor function in PD, especially akinesia. The beneficial effects were similar to those of high-intensity rehabilitation programs. Copyright © 2018 Korean Neurological Association.

In Vitro Quantification of Gutter Formation and Chimney Graft Compression in Chimney EVAR Stent-Graft Configurations Using Electrocardiography-Gated Computed Tomography.

PubMed

Overeem, Simon P; Donselaar, Esmé J; Boersen, Jorrit T; Groot Jebbink, Erik; Slump, Cornelis H; de Vries, Jean-Paul P M; Reijnen, Michel M P J

2018-03-01

To assess the dynamic behavior of chimney grafts during the cardiac cycle. Three chimney endovascular aneurysm repair (EVAR) stent-graft configurations (Endurant and Advanta V12, Endurant and Viabahn, and Endurant and BeGraft) were placed in silicone aneurysm models and subjected to physiologic flow. Electrocardiography (ECG)-gated contrast-enhanced computed tomography was used to visualize geometric changes during the cardiac cycle. Endograft and chimney graft surface, gutter volume, chimney graft angulation over the center lumen line, and the D-ratio (the ratio between the lengths of the major and minor axes) were independently assessed by 2 observers at 10 time points in the cardiac cycle. Both gutter volumes and chimney graft geometry changed significantly during the cardiac cycle in all 3 configurations (p<0.001). Gutters and endoleaks were observed in all configurations. The largest gutter volume (232.8 mm 3 ) and change in volume (20.7 mm 3 ) between systole and diastole were observed in the Endurant-Advanta configuration. These values were 2.7- and 3.0-fold higher, respectively, compared to the Endurant-Viabahn configuration and 1.7- and 1.6-fold higher as observed in the Endurant-BeGraft configuration. The Endurant-Viabahn configuration had the highest D-ratio (right, 1.26-1.35; left, 1.33-1.48), while the Endurant-BeGraft configuration had the lowest (right, 1.11-1.17; left, 1.08-1.15). Assessment of the interobserver variability showed a high correlation (intraclass correlation >0.935) between measurements. Gutter volumes and stent compression are dynamic phenomena that reshape during the cardiac cycle. Compelling differences were observed during the cardiac cycle in all configurations, with the self-expanding (Endurant-Viabahn) chimney EVAR configurations having smaller gutters and less variation in gutter volume during the cardiac cycle yet more stent compression without affecting the chimney graft surface.

Alternatives Assessment Frameworks: Research Needs for the Informed Substitution of Hazardous Chemicals

PubMed Central

Jacobs, Molly M.; Malloy, Timothy F.; Tickner, Joel A.; Edwards, Sally

2015-01-01

Background Given increasing pressures for hazardous chemical replacement, there is growing interest in alternatives assessment to avoid substituting a toxic chemical with another of equal or greater concern. Alternatives assessment is a process for identifying, comparing, and selecting safer alternatives to chemicals of concern (including those used in materials, processes, or technologies) on the basis of their hazards, performance, and economic viability. Objectives The purposes of this substantive review of alternatives assessment frameworks are to identify consistencies and differences in methods and to outline needs for research and collaboration to advance science policy practice. Methods This review compares methods used in six core components of these frameworks: hazard assessment, exposure characterization, life-cycle impacts, technical feasibility evaluation, economic feasibility assessment, and decision making. Alternatives assessment frameworks published from 1990 to 2014 were included. Results Twenty frameworks were reviewed. The frameworks were consistent in terms of general process steps, but some differences were identified in the end points addressed. Methodological gaps were identified in the exposure characterization, life-cycle assessment, and decision–analysis components. Methods for addressing data gaps remain an issue. Discussion Greater consistency in methods and evaluation metrics is needed but with sufficient flexibility to allow the process to be adapted to different decision contexts. Conclusion Although alternatives assessment is becoming an important science policy field, there is a need for increased cross-disciplinary collaboration to refine methodologies in support of the informed substitution and design of safer chemicals, materials, and products. Case studies can provide concrete lessons to improve alternatives assessment. Citation Jacobs MM, Malloy TF, Tickner JA, Edwards S. 2016. Alternatives assessment frameworks: research needs for the informed substitution of hazardous chemicals. Environ Health Perspect 124:265–280; http://dx.doi.org/10.1289/ehp.1409581 PMID:26339778

Geographical scenario uncertainty in generic fate and exposure factors of toxic pollutants for life-cycle impact assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huijbregts, Mark A.J.; Lundi, Sven; McKone, Thomas E.

In environmental life-cycle assessments (LCA), fate and exposure factors account for the general fate and exposure properties of chemicals under generic environmental conditions by means of 'evaluative' multi-media fate and exposure box models. To assess the effect of using different generic environmental conditions, fate and exposure factors of chemicals emitted under typical conditions of (1) Western Europe, (2) Australia and (3) the United States of America were compared with the multi-media fate and exposure box model USES-LCA. Comparing the results of the three evaluative environments, it was found that the uncertainty in fate and exposure factors for ecosystems and humansmore » due to choice of an evaluative environment, as represented by the ratio of the 97.5th and 50th percentile, is between a factor 2 and 10. Particularly, fate and exposure factors of emissions causing effects in fresh water ecosystems and effects on human health have relatively high uncertainty. This uncertainty i s mainly caused by the continental difference in the average soil erosion rate, the dimensions of the fresh water and agricultural soil compartment, and the fraction of drinking water coming from ground water.« less

Application of a life cycle assessment to compare environmental performance in coal mine tailings management.

PubMed

Adiansyah, Joni Safaat; Haque, Nawshad; Rosano, Michele; Biswas, Wahidul

2017-09-01

This study compares coal mine tailings management strategies using life cycle assessment (LCA) and land-use area metrics methods. Hybrid methods (the Australian indicator set and the ReCiPe method) were used to assess the environmental impacts of tailings management strategies. Several strategies were considered: belt filter press (OPT 1), tailings paste (OPT 2), thickened tailings (OPT 3), and variations of OPT 1 using combinations of technology improvement and renewable energy sources (OPT 1A-D). Electrical energy was found to contribute more than 90% of the environmental impacts. The magnitude of land-use impacts associated with OPT 3 (thickened tailings) were 2.3 and 1.55 times higher than OPT 1 (tailings cake) and OPT 2 (tailings paste) respectively, while OPT 1B (tailings belt filter press with technology improvement and solar energy) and 1D (tailings belt press filter with technology improvement and wind energy) had the lowest ratio of environmental impact to land-use. Further analysis of an economic cost model and reuse opportunities is required to aid decision making on sustainable tailings management and industrial symbiosis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Life Cycle Assessment for Biofuels

EPA Science Inventory

A presentation based on life cycle assessment (LCA) for biofuels is given. The presentation focuses on energy and biofuels, interesting environmental aspects of biofuels, and how to do a life cycle assessment with some examples related to biofuel systems. The stages of a (biofuel...

LIFE CYCLE ASSESSMENT: PRINCIPLES AND PRACTICE

EPA Science Inventory

The following document provides an introductory overview of Life Cycle Assessment (LCA) and describes the general uses and major components of LCA. This document is an update and merger of two previous EPA documents on LCA ("Life Cycle Assessment: Inventory Guidelines and Princip...

A framework for an alternatives assessment dashboard for evaluating chemical alternatives applied to flame retardants for electronic applications.

PubMed

Martin, Todd M

2017-05-01

The goal of alternatives assessment (AA) is to facilitate a comparison of alternatives to a chemical of concern, resulting in the identification of safer alternatives. A two stage methodology for comparing chemical alternatives was developed. In the first stage, alternatives are compared using a variety of human health effects, ecotoxicity, and physicochemical properties. Hazard profiles are completed using a variety of online sources and quantitative structure activity relationship models. In the second stage, alternatives are evaluated utilizing an exposure/risk assessment over the entire life cycle. Exposure values are calculated using screening-level near-field and far-field exposure models. The second stage allows one to more accurately compare potential exposure to each alternative and consider additional factors that may not be obvious from separate binned persistence, bioaccumulation, and toxicity scores. The methodology was utilized to compare phosphate-based alternatives for decabromodiphenyl ether (decaBDE) in electronics applications.

Global and local health burden trade-off through the hybridisation of quantitative microbial risk assessment and life cycle assessment to aid water management.

PubMed

Kobayashi, Yumi; Peters, Greg M; Ashbolt, Nicholas J; Heimersson, Sara; Svanström, Magdalena; Khan, Stuart J

2015-08-01

Life cycle assessment (LCA) and quantitative risk assessment (QRA) are commonly used to evaluate potential human health impacts associated with proposed or existing infrastructure and products. Each approach has a distinct objective and, consequently, their conclusions may be inconsistent or contradictory. It is proposed that the integration of elements of QRA and LCA may provide a more holistic approach to health impact assessment. Here we examine the possibility of merging LCA assessed human health impacts with quantitative microbial risk assessment (QMRA) for waterborne pathogen impacts, expressed with the common health metric, disability adjusted life years (DALYs). The example of a recent large-scale water recycling project in Sydney, Australia was used to identify and demonstrate the potential advantages and current limitations of this approach. A comparative analysis of two scenarios - with and without the development of this project - was undertaken for this purpose. LCA and QMRA were carried out independently for the two scenarios to compare human health impacts, as measured by DALYs lost per year. LCA results suggested that construction of the project would lead to an increased number of DALYs lost per year, while estimated disease burden resulting from microbial exposures indicated that it would result in the loss of fewer DALYs per year than the alternative scenario. By merging the results of the LCA and QMRA, we demonstrate the advantages in providing a more comprehensive assessment of human disease burden for the two scenarios, in particular, the importance of considering the results of both LCA and QRA in a comparative assessment of decision alternatives to avoid problem shifting. The application of DALYs as a common measure between the two approaches was found to be useful for this purpose. Copyright © 2015 Elsevier Ltd. All rights reserved.

Life cycle assessment of fertilization of corn and corn-soybean rotations with Swine manure and synthetic fertilizer in iowa.

PubMed

Griffing, Evan Michael; Schauer, Richard Lynn; Rice, Charles W

2014-03-01

Life cycle assessment is the predominant method to compare energy and environmental impacts of agricultural production systems. In this life cycle study, we focused on the comparison of swine manure to synthetic fertilizer as nutrients for corn production in Iowa. Deep pit (DP) and anaerobic lagoon (AL) treatment systems were compared separately, and urea ammonium nitrate (UAN) was chosen as the representative synthetic fertilizer. The two functional units used were fertilization of 1000 kg of corn in a continuous corn system and fertilization of a crop yielding 1000 kg of corn and a crop yielding 298 kg of soybean in a 2-yr corn-soybean rotation. Iowa-specific versions of emission factors and energy use were used when available and compared with Intergovernmental Panel on Climate Change values. Manure was lower than synthetic fertilizer for abiotic depletion and about equal with respect to eutrophication. Synthetic fertilizer was lower than manure for global warming potential (GWP) and acidification. The choice of allocation method and life cycle boundary were important in understanding the context of these results. In the DP system, methane (CH) from housing was the largest contributor to the GWP, accounting for 60% of the total impact. When storage systems were compared, the DP system had 50% less GWP than the AL system. This comparison was due to reduction in CH emissions from the storage system and conservation of nitrogen. Nitrous oxide emissions were the biggest contributor to the GWP of UAN fertilization and the second biggest contributor to the GWP of manure. Monte Carlo and scenario analyses were used to test the robustness of the results and sensitivity to methodology and important impact factors. The available crop-land and associated plant nutrient needs in Iowa was compared with manure production for the current hog population. On a state- or county-wide level, there was generally an excess of available land. On a farm level, there is often an excess of manure, which necessitates long-distance transport. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

High-resolution assessment of land use impacts on biodiversity in life cycle assessment using species habitat suitability models.

PubMed

de Baan, Laura; Curran, Michael; Rondinini, Carlo; Visconti, Piero; Hellweg, Stefanie; Koellner, Thomas

2015-02-17

Agricultural land use is a main driver of global biodiversity loss. The assessment of land use impacts in decision-support tools such as life cycle assessment (LCA) requires spatially explicit models, but existing approaches are either not spatially differentiated or modeled at very coarse scales (e.g., biomes or ecoregions). In this paper, we develop a high-resolution (900 m) assessment method for land use impacts on biodiversity based on habitat suitability models (HSM) of mammal species. This method considers potential land use effects on individual species, and impacts are weighted by the species' conservation status and global rarity. We illustrate the method using a case study of crop production in East Africa, but the underlying HSMs developed by the Global Mammals Assessment are available globally. We calculate impacts of three major export crops and compare the results to two previously developed methods (focusing on local and regional impacts, respectively) to assess the relevance of the methodological innovations proposed in this paper. The results highlight hotspots of product-related biodiversity impacts that help characterize the links among agricultural production, consumption, and biodiversity loss.

Carbon-Carbon Recuperators in Closed-Brayton-Cycle Space Power Systems

NASA Technical Reports Server (NTRS)

Barrett, Michael J.; Johnson, Paul K.; Naples, Andrew G.

2006-01-01

The feasibility of using carbon-carbon (C-C) recuperators in conceptual closed-Brayton-cycle space power conversion systems was assessed. Recuperator performance expectations were forecast based on notional thermodynamic cycle state values for potential planetary missions. Resulting thermal performance, mass and volume for plate-fin C-C recuperators were estimated and quantitatively compared with values for conventional offset-strip-fin metallic designs. Mass savings of 30 to 60 percent were projected for C-C recuperators with effectiveness greater than 0.9 and thermal loads from 25 to 1400 kWt. The smaller thermal loads corresponded with lower mass savings; however, 60 percent savings were forecast for all loads above 300 kWt. System-related material challenges and compatibility issues were also discussed.

Life Cycle Cost Analysis of Shuttle-Derived Launch Vehicles, Volume 1

NASA Technical Reports Server (NTRS)

1982-01-01

The design, performance, and programmatic definition of shuttle derived launch vehicles (SDLV) established by two different contractors were assessed and the relative life cycle costs of space transportation systems using the shuttle alone were compared with costs for a mix of shuttles and SDLV's. The ground rules and assumptions used in the evaluation are summarized and the work breakdown structure is included. Approaches used in deriving SDLV costs, including calibration factors and historical data are described. Both SDLV cost estimates and SDLV/STS cost comparisons are summarized. Standard formats are used to report comprehensive SDLV life cycle estimates. Hardware cost estimates (below subsystem level) obtained using the RCA PRICE 84 cost model are included along with other supporting data.

Integrating algaculture into small wastewater treatment plants: process flow options and life cycle impacts.

PubMed

Steele, Muriel M; Anctil, Annick; Ladner, David A

2014-05-01

Algaculture has the potential to be a sustainable option for nutrient removal at wastewater treatment plants. The purpose of this study was to compare the environmental impacts of three likely algaculture integration strategies to a conventional nutrient removal strategy. Process modeling was used to determine life cycle inventory data and a comparative life cycle assessment was used to determine environmental impacts. Treatment scenarios included a base case treatment plant without nutrient removal, a plant with conventional nutrient removal, and three other cases with algal unit processes placed at the head of the plant, in a side stream, and at the end of the plant, respectively. Impact categories included eutrophication, global warming, ecotoxicity, and primary energy demand. Integrating algaculture prior to activated sludge proved to be most beneficial of the scenarios considered for all impact categories; however, this scenario would also require primary sedimentation and impacts of that unit process should be considered for implementation of such a system.

Alberta Carpenter | NREL

Science.gov Websites

cycle assessment in industrial by-product management, waste management, biofuels and manufacturing technologies Life cycle inventory database management Research Interests Life cycle assessment Life cycle inventory management Biofuels Advanced manufacturing Supply chain analysis Education Ph.D in environmental

How compliant are in vitro fertilization member clinics in following embryo transfer guidelines? An analysis of 59,689 fresh first in vitro fertilization autologous cycles from 2011 to 2012.

PubMed

Keyhan, Sanaz; Acharya, Kelly S; Acharya, Chaitanya R; Yeh, Jason S; Provost, Meredith P; Goldfarb, James M; Muasher, Suheil J

2016-09-01

To determine whether IVF clinics are compliant with American Society for Reproductive Medicine (ASRM) and Society for Assisted Reproductive Technology (SART) (ASRM/SART) guidelines and assess the multiple pregnancy outcomes according to the number of embryos transferred. Retrospective cohort study. Not applicable. Data from 59,689 fresh first autologous IVF cycles from the 2011-2012 SART registry. None. Percentage of compliant cycles, multiple pregnancy rate (PR). Between 2011 and 2012, a total of 59,689 fresh first autologous cycles were analyzed. Among cleavage-stage ET cycles, the noncompliance rate ranged from 10%-27.4% depending on the age group. The multiple PR was significantly increased in noncompliant cycles involving patients <35 years (38.1% vs. 28.7%) and 35-37 years (35.4% vs. 24.5%) compared with compliant cycles. Among blastocyst-stage ET cycles, the highest rate of noncompliance was seen in patients <35 years old (71%), which resulted in a statistically higher multiple PR (48.3% vs. 2.8%) compared with compliant cycles. Far fewer cycles were noncompliant in patients 35-40 years of age. In a subanalysis of compliant cycles, transferring two blastocyst embryos in patients 35-37 years and 38-40 years resulted in a higher live birth rate compared with the transfer of one embryo (50.4% vs. 40.9% and 42.1% vs. 30.0%, respectively) but the multiple PR was also significantly higher (40.5% vs. 1.7% and 34.0% vs. 2.0%, respectively). Most first fresh autologous IVF cycles performed from 2011-2012 were compliant with ASRM/SART guidelines, except those that involved a blastocyst ET in patients <35 years. Despite compliance, cycles that involved the transfer of >1 embryo resulted in a high multiple PR, whereas noncompliant cycles resulted in an even more remarkable multiple PR for both cleavage and blastocyst-stage embryos. Clinics need to be more compliant with ET limits and ASRM/SART need to consider revising their guidelines to limit the number of blastocyst transfer to one in patients ≤40 years of age undergoing their first IVF cycle. Furthermore, decreasing the number of cleavage-stage embryos transferred in patients ≤40 years of age should also be considered. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Quantified Uncertainties in Comparative Life Cycle Assessment: What Can Be Concluded?

PubMed Central

2018-01-01

Interpretation of comparative Life Cycle Assessment (LCA) results can be challenging in the presence of uncertainty. To aid in interpreting such results under the goal of any comparative LCA, we aim to provide guidance to practitioners by gaining insights into uncertainty-statistics methods (USMs). We review five USMs—discernibility analysis, impact category relevance, overlap area of probability distributions, null hypothesis significance testing (NHST), and modified NHST–and provide a common notation, terminology, and calculation platform. We further cross-compare all USMs by applying them to a case study on electric cars. USMs belong to a confirmatory or an exploratory statistics’ branch, each serving different purposes to practitioners. Results highlight that common uncertainties and the magnitude of differences per impact are key in offering reliable insights. Common uncertainties are particularly important as disregarding them can lead to incorrect recommendations. On the basis of these considerations, we recommend the modified NHST as a confirmatory USM. We also recommend discernibility analysis as an exploratory USM along with recommendations for its improvement, as it disregards the magnitude of the differences. While further research is necessary to support our conclusions, the results and supporting material provided can help LCA practitioners in delivering a more robust basis for decision-making. PMID:29406730

Life cycle assessment of a road safety product made with virgin and recycled HDPE.

PubMed

Simões, Carla L; Xará, Susana M; Bernardo, C A

2011-04-01

The present study aims at evaluating the potential environmental impact of using recycled high-density polyethylene (HDPE) in the production of an anti-glare lamella (AGL), a road safety device currently manufactured from virgin (not recycled) polymer. The impact was evaluated using the life cycle assessment (LCA) technique and comparing two alternative systems: current AGL, manufactured from virgin HDPE, and optional AGL, made with recycled HDPE obtained from post-consumer packages. The AGL manufacturing phase was found to be responsible for most of the impacts in both systems, with the production of the raw material being the largest contributor for that phase. The present study makes a contribution to the problem of developing value-added products made from post-consumer polymeric recyclates.

A Cycle Ergometer Exercise Program Improves Exercise Capacity and Inspiratory Muscle Function in Hospitalized Patients Awaiting Heart Transplantation: a Pilot Study

PubMed Central

Forestieri, Patrícia; Guizilini, Solange; Peres, Monique; Bublitz, Caroline; Bolzan, Douglas W.; Rocco, Isadora S.; Santos, Vinícius B.; Moreira, Rita Simone L.; Breda, João R.; de Almeida, Dirceu R.; Carvalho, Antonio Carlos de C.; Arena, Ross; Gomes, Walter J.

2016-01-01

Objective The purpose of this study was to evaluate the effect of a cycle ergometer exercise program on exercise capacity and inspiratory muscle function in hospitalized patients with heart failure awaiting heart transplantation with intravenous inotropic support. Methods Patients awaiting heart transplantation were randomized and allocated prospectively into two groups: 1) Control Group (n=11) - conventional protocol; and 2) Intervention Group (n=7) - stationary cycle ergometer exercise training. Functional capacity was measured by the six-minute walk test and inspiratory muscle strength assessed by manovacuometry before and after the exercise protocols. Results Both groups demonstrated an increase in six-minute walk test distance after the experimental procedure compared to baseline; however, only the intervention group had a significant increase (P=0.08 and P=0.001 for the control and intervention groups, respectively). Intergroup comparison revealed a greater increase in the intervention group compared to the control (P<0.001). Regarding the inspiratory muscle strength evaluation, the intragroup analysis demonstrated increased strength after the protocols compared to baseline for both groups; statistical significance was only demonstrated for the intervention group, though (P=0.22 and P<0.01, respectively). Intergroup comparison showed a significant increase in the intervention group compared to the control (P<0.01). Conclusion Stationary cycle ergometer exercise training shows positive results on exercise capacity and inspiratory muscle strength in patients with heart failure awaiting cardiac transplantation while on intravenous inotropic support. PMID:27982348

Life Cycle Impact Assessment of a Rainwater Harvesting System Compared with an A/C Condensate System

EPA Science Inventory

This study reviewed U.S. commercial buildings to design a decentralized rooftop rainwater harvesting (RWH) system and air-conditioning (AC) condensate harvesting (ACH) system for non-potable use. RWH systems were designed for one-to multi-story buildings selected from each of th...

COMPARISON OF CHEMICAL SCREENING AND RANKING APPROACHES: THE WASTE MINIMIZATION PRIORITIZATION TOOL VERSUS TOXIC EQUIVALENCY POTENTIALS

EPA Science Inventory

Chemical screening in the United States is often conducted using scoring and ranking methodologies. Linked models accounting for chemical fate, exposure, and toxicological effects are generally preferred in Europe and in product Life Cycle Assessment. For the first time, a compar...

A Review of Environmental Life Cycle Assessments of Liquid Transportation Biofuels in the Pan American Region

NASA Astrophysics Data System (ADS)

Shonnard, David R.; Klemetsrud, Bethany; Sacramento-Rivero, Julio; Navarro-Pineda, Freddy; Hilbert, Jorge; Handler, Robert; Suppen, Nydia; Donovan, Richard P.

2015-12-01

Life-cycle assessment (LCA) has been applied to many biofuel and bioenergy systems to determine potential environmental impacts, but the conclusions have varied. Different methodologies and processes for conducting LCA of biofuels make the results difficult to compare, in-turn making it difficult to make the best possible and informed decision. Of particular importance are the wide variability in country-specific conditions, modeling assumptions, data quality, chosen impact categories and indicators, scale of production, system boundaries, and co-product allocation. This study has a double purpose: conducting a critical evaluation comparing environmental LCA of biofuels from several conversion pathways and in several countries in the Pan American region using both qualitative and quantitative analyses, and making recommendations for harmonization with respect to biofuel LCA study features, such as study assumptions, inventory data, impact indicators, and reporting practices. The environmental management implications are discussed within the context of different national and international regulatory environments using a case study. The results from this study highlight LCA methodology choices that cause high variability in results and limit comparability among different studies, even among the same biofuel pathway, and recommendations are provided for improvement.

A Review of Environmental Life Cycle Assessments of Liquid Transportation Biofuels in the Pan American Region.

PubMed

Shonnard, David R; Klemetsrud, Bethany; Sacramento-Rivero, Julio; Navarro-Pineda, Freddy; Hilbert, Jorge; Handler, Robert; Suppen, Nydia; Donovan, Richard P

2015-12-01

Life-cycle assessment (LCA) has been applied to many biofuel and bioenergy systems to determine potential environmental impacts, but the conclusions have varied. Different methodologies and processes for conducting LCA of biofuels make the results difficult to compare, in-turn making it difficult to make the best possible and informed decision. Of particular importance are the wide variability in country-specific conditions, modeling assumptions, data quality, chosen impact categories and indicators, scale of production, system boundaries, and co-product allocation. This study has a double purpose: conducting a critical evaluation comparing environmental LCA of biofuels from several conversion pathways and in several countries in the Pan American region using both qualitative and quantitative analyses, and making recommendations for harmonization with respect to biofuel LCA study features, such as study assumptions, inventory data, impact indicators, and reporting practices. The environmental management implications are discussed within the context of different national and international regulatory environments using a case study. The results from this study highlight LCA methodology choices that cause high variability in results and limit comparability among different studies, even among the same biofuel pathway, and recommendations are provided for improvement.

Dietary minerals, reproductive hormone levels and sporadic anovulation: associations in healthy women with regular menstrual cycles.

PubMed

Kim, Keewan; Wactawski-Wende, Jean; Michels, Kara A; Schliep, Karen C; Plowden, Torie C; Chaljub, Ellen N; Mumford, Sunni L

2018-04-20

Although minerals are linked to several reproductive outcomes, it is unknown whether dietary minerals are associated with ovulatory function. We hypothesised that low intakes of minerals would be associated with an increased risk of anovulation. We investigated associations between dietary mineral intake and both reproductive hormones and anovulation in healthy women in the BioCycle Study, which prospectively followed up 259 regularly menstruating women aged 18-44 years who were not taking mineral supplements for two menstrual cycles. Intakes of ten selected minerals were assessed through 24-h dietary recalls at up to four times per cycle in each participant. Oestradiol, progesterone, luteinising hormone (LH), follicle-stimulating hormone (FSH), sex-hormone-binding globulin and testosterone were measured in serum up to eight times per cycle. We used weighted linear mixed models to evaluate associations between minerals and hormones and generalised linear models for risk of anovulation. Compared with Na intake ≥1500 mg, Na intake <1500 mg was associated with higher levels of FSH (21·3 %; 95 % CI 7·5, 36·9) and LH (36·8 %; 95 % CI 16·5, 60·5) and lower levels of progesterone (-36·9 %; 95 % CI -56·5, -8·5). Na intake <1500 mg (risk ratio (RR) 2·70; 95 % CI 1·00, 7·31) and Mn intake <1·8 mg (RR 2·00; 95 % CI 1·02, 3·94) were associated with an increased risk of anovulation, compared with higher intakes, respectively. Other measured dietary minerals were not associated with ovulatory function. As essential minerals are mostly obtained via diet, our results comparing insufficient levels with sufficient levels highlight the need for future research on dietary nutrients and their associations with ovulatory cycles.

Changes in skin blood flow during the menstrual cycle: the influence of the menstrual cycle on the peripheral circulation in healthy female volunteers.

PubMed

Bartelink, M L; Wollersheim, H; Theeuwes, A; van Duren, D; Thien, T

1990-05-01

1. It is known that females have a lower skin perfusion than males. In women there are also differences in blood flow at different reproductive stages of their lives. As an initial investigation of the possible contribution of sex hormones to these differences, we studied skin and forearm blood flow during the natural changes in hormone levels which occur during the menstrual cycle. 2. Thirty-one healthy female volunteers were studied. The effect of a standardized finger cooling test (immersion of a gloved hand in a 16 degrees C water bath) on finger skin temperature and on laser Doppler flux in the finger, and forearm blood flow (strain gauge venous occlusion plethysmography) was assessed at four different times during one cycle: during menstruation, 1 day before ovulation, 2 days after ovulation and at the mid-luteal phase. Test days were determined by daily measurements of basal body temperature and were confirmed afterwards by determinations of serum luteinizing hormone, follicle-stimulating hormone, 17 beta-oestradiol and progesterone. 3. Peripheral skin circulation varied significantly within one menstrual cycle. The extremes were a mean finger skin temperature of 25.9 +/- 3.0 degrees C in the luteal phase compared with 28.4 +/- 3.7 degrees C in the pre-ovulatory phase (P = 0.002). The respective values for the mean laser Doppler flux were 18.4 +/- 10.9 compared with 29.2 +/- 16.4 arbitrary units (P = 0.003). 4. Baseline forearm muscle blood flow also varied significantly (P = 0.04) within one menstrual cycle, with low values in the menstrual phase compared with the other phases.(ABSTRACT TRUNCATED AT 250 WORDS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The SPS Concept Development and Evaluation Program includes a comparative assessment. An early first step in the assessment process is the selection and characterization of alternative technologies. This document describes the cost and performance (i.e., technical and environmental) characteristics of six central station energy alternatives: (1) conventional coal-fired powerplant; (2) conventional light water reactor (LWR); (3) combined cycle powerplant with low-Btu gasifiers; (4) liquid metal fast breeder reactor (LMFBR); (5) photovoltaic system without storage; and (6) fusion reactor.

Inducing myoblast re-entry into the cell cycle: a potential mechanism for laser-enhanced skeletal muscle regeneration

NASA Astrophysics Data System (ADS)

Liu, T.; Fang, Y.; Zhang, C. P.; Chen, P.; Wang, C. Z.; Kang, H. X.; Shen, B. J.; Liang, J.; Fu, X. B.

2014-09-01

This study investigated the effect of low-level laser irradiation (LLLI) on the cell cycle and proliferative activity of cultured myoblasts, and sought to elucidate the possible cellular mechanism by which LLLI promotes the regeneration of skeletal muscle in vivo. Primary myoblasts isolated from rat hindlegs were irradiated with helium-neon laser light at different energy densities. Distributions of cell-cycle subpopulations and the expression of cell-cycle regulatory proteins in myoblasts were assessed using flow cytometric analysis and western blot assay. It was found that laser irradiation stimulated cell-cycle entry; induced the expression of cyclin A and cyclin D; and increased cell proliferation index and bromodeoxyuridine incorporation as compared to the unirradiated control cells, indicating LLLI augmented the number of proliferative myoblasts in the S phase and G2/M phase of the cell cycle. These results suggest that LLLI at certain fluxes and wavelengths could activate quiescent myoblasts, leading to cell division and facilitating new myofiber formation. This could contribute to the improvement of skeletal muscle regeneration following trauma and myopathic diseases.

[Do poor-responder patients benefit from increasing the daily gonadotropin dose from 300 to 450 IU during controlled ovarian hyperstimulation for IVF?].

PubMed

Haas, Jigal; Zilberberg, Eran; Kedem, Alon; Dar, Shir; Orvieto, Raoul

2015-02-01

We aim to evaluate the IVF-ET outcome in patients receiving a high daily dose (300 IU) of gonadotropins during controlled ovarian hyperstimulation (COH) for IVF and to assess the role of increasing the daily dose to 450 IU on improving outcome. All consecutive women admitted to our IVF unit during an 11 year period who underwent COH consisting of daily gonadotropin dose of 300 IU were included in the study. The ovarian stimulation characteristics, number of oocytes retrieved, number of embryo transferred and pregnancy rate were assessed. We also evaluated the subsequent cycle, using daily gonadotropin doses of 450 IU, among those patients who did not conceive using the 300 IU daily gonadotropin dose. Nine hundred and forty-nine consecutive IVF cycles were evaluated. Patients who conceived using the daily gonadotropin dose of 300 IU (n = 133, 14% pregnancy rate) had significantly longer stimulation, yielded higher numbers of oocytes retrieved, fertilization rate and number of embryos transferred, compared to those who did not conceive. Moreover, while comparing IVF cycles using daily gonadotropin doses of 300 IU to 450 IU (n = 117), no in-between group differences were observed, except for significantly higher yields of oocytes retrieved. Moreover, cycles using daily gonadotropin doses of 450 IU resulted in a 7.7 live-birth rate. In poor responders undergoing COH with a daily gonadotropin dose of 300 IU, increasing the dose to 450 IU resulted in significantly higher oocyte yields and a reasonable live birth rate.

Energy and cost saving results for advanced technology systems from the Cogeneration Technology Alternatives Study (CTAS)

NASA Technical Reports Server (NTRS)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

An overview of the organization and methodology of the Cogeneration Technology Alternatives Study is presented. The objectives of the study were to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the future and to assess the advantages of advanced technology systems compared to those systems commercially available today. Advanced systems studied include steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics. Steam turbines, open cycle gas turbines, combined cycles, and diesel engines were also analyzed in versions typical of today's commercially available technology to provide a base against which to measure the advanced systems. Cogeneration applications in the major energy consuming manufacturing industries were considered. Results of the study in terms of plant level energy savings, annual energy cost savings and economic attractiveness are presented for the various energy conversion systems considered.

Integrative Application of Life Cycle Assessment and Risk Assessment to Environmental Impacts of Anthropogenic Pollutants at a Watershed Scale.

PubMed

Lin, Xiaodan; Yu, Shen; Ma, Hwongwen

2018-01-01

Intense human activities have led to increasing deterioration of the watershed environment via pollutant discharge, which threatens human health and ecosystem function. To meet a need of comprehensive environmental impact/risk assessment for sustainable watershed development, a biogeochemical process-based life cycle assessment and risk assessment (RA) integration for pollutants aided by geographic information system is proposed in this study. The integration is to frame a conceptual protocol of "watershed life cycle assessment (WLCA) for pollutants". The proposed WLCA protocol consists of (1) geographic and environmental characterization mapping; (2) life cycle inventory analysis; (3) integration of life-cycle impact assessment (LCIA) with RA via characterization factor of pollutant of interest; and (4) result analysis and interpretation. The WLCA protocol can visualize results of LCIA and RA spatially for the pollutants of interest, which might be useful for decision or policy makers for mitigating impacts of watershed development.

Impact on clinical practice of the implementation of guidelines for the toxicity management of targeted therapies in kidney cancer. The protect-2 study.

PubMed

Lainez, Nuria; García-Donas, Jesús; Esteban, Emilio; Puente, Javier; Sáez, M Isabel; Gallardo, Enrique; Pinto-Marín, Álvaro; Vázquez-Estévez, Sergio; León, Luis; García-Carbonero, Icíar; Suárez-Rodríguez, Cristina; Molins, Carmen; Climent-Duran, Miguel A; Lázaro-Quintela, Martín; González Del Alba, Aranzazu; Méndez-Vidal, María José; Chirivella, Isabel; Afonso, Francisco J; López-Brea, Marta; Sala-González, Nuria; Domenech, Montserrat; Basterretxea, Laura; Santander-Lobera, Carmen; Gil-Arnáiz, Irene; Fernández, Ovidio; Caballero-Díaz, Cristina; Mellado, Begoña; Marrupe, David; García-Sánchez, José; Sánchez-Escribano, Ricardo; Fernández Parra, Eva; Villa Guzmán, José C; Martínez-Ortega, Esther; Belén González, María; Morán, Marina; Suarez-Paniagua, Beatriz; Lecumberri, María J; Castellano, Daniel

2016-02-22

The impact of such recommendations after their implementation of guidelines has not usually been evaluated. Herein, we assessed the impact and compliance with the Spanish Oncology Genitourinary Group (SOGUG) Guidelines for toxicity management of targeted therapies in metastatic renal cell carcinoma (mRCC) in daily clinical practice. Data on 407 mRCC patients who initiated first-line targeted therapy during the year before and the year after publication and implementation of the SOGUG guideline program were available from 34 Spanish Hospitals. Adherence to SOGUG Guidelines was assessed in every cycle. Adverse event (AE) management was consistent with the Guidelines as a whole for 28.7% out of 966 post-implementation cycles compared with 23.1% out of 892 pre-implementation cycles (p = 0.006). Analysis of adherence by AE in non-compliant cycles showed significant changes in appropriate management of hypertension (33% pre-implementation vs. 44.5% post-implementation cycles; p < 0.0001), diarrhea (74.0% vs. 80.5%; p = 0.011) and dyslipemia (25.0% vs. 44.6%; p < 0.001). Slight but significant improvements in AE management were detected following the implementation of SOGUG recommendations. However, room for improvement in the management of AEs due to targeted agents still remains and could be the focus for further programs in this direction.

[Influence of stimulation and blockade of α4β2 nicotinic acetylcholine receptors on learning of female rats in basic phases of ovary cycle].

PubMed

Fedotova, Iu O

2014-03-01

The present work was devoted to the comparative analysis of α4β2 nicotinic acetylcholine receptors (nAChRs) in learning/memory processes during ovary cycle in the adult female rats. RJR-2403 (1.0 mg/kg, i. p.), α4β2 nAChRs agonist and mecamylamine (1.0 mg/kg, i. p.), α4β2 nAChRs antagonist were injected chronically during 14 days. The processes of learning/memory were assessed in different models of learning: passive avoidance performance and Morris water maze. Chronic RJR-2403 administration to females improved the passive avoidance performance in proestrous and estrous as compared to the control animals. Also, RJR-2403 restored spatial learning of rats during proestrous phases in Morris water maze, and stimulated the dynamics of spatial learning during estrous phases. On the contrary, the chronic mecamylamine administration impaired non-spatial, and especially, spatial learning in females during key phases of ovary cycle. The results of the study suggest positive effect of α4β2 nAChRs stimulation in learning/memory processes during ovary cycle in the adult female rats.

Geothermal Water Use: Life Cycle Water Consumption, Water Resource Assessment, and Water Policy Framework

DOE Data Explorer

Schroeder, Jenna N.

2014-06-10

This report examines life cycle water consumption for various geothermal technologies to better understand factors that affect water consumption across the life cycle (e.g., power plant cooling, belowground fluid losses) and to assess the potential water challenges that future geothermal power generation projects may face. Previous reports in this series quantified the life cycle freshwater requirements of geothermal power-generating systems, explored operational and environmental concerns related to the geochemical composition of geothermal fluids, and assessed future water demand by geothermal power plants according to growth projections for the industry. This report seeks to extend those analyses by including EGS flash, both as part of the life cycle analysis and water resource assessment. A regional water resource assessment based upon the life cycle results is also presented. Finally, the legal framework of water with respect to geothermal resources in the states with active geothermal development is also analyzed.

LIFE CYCLE ASSESSMENT FOR PC BLEND 2 AIRCRAFT RADOME DEPAINTER

EPA Science Inventory

This report describes the life cycle assessment on a potential replacement solvent blend for aircraft radome depainting at the Oklahoma City Air Logistics Center at Tinker Air Force Base. The life cycle assessment is composed of three separate but interrelated components: life cy...

EDITORIAL: THE INTERNATIONAL CONFERENCE ON LIFE CYCLE ASSESSMENT

EPA Science Inventory

This is a special issue of Journal of Life Cycle Assessment that includes selected papers from the Internatonal Conference and Exhibition on Life Cycle Assessment (InLCA). In April 2000, the EPA, with co-organizer IERE, held the InLCA conferencethat attracted over 265 attendees (...

Differential Interactions between Comorbid Anxiety Disorders and Substance Use Disorder in Rapid Cycling Bipolar I or II Disorder

PubMed Central

Gao, Keming; Tolliver, Bryan; Kemp, David E.; Verduin, Marcia L.; Ganocy, Stephen J.; Bilali, Sarah; Brady, Kathleen; Shim, Seong S.; Findling, Robert; Calabrese, Joseph R.

2008-01-01

Objective Anxiety disorders (AD) and substance use disorders (SUD) commonly co-occur with bipolar disorder. This study was undertaken to assess AD-SUD-bipolar subtype interactions. Methods Extensive clinical interview and MINI were used to ascertain DSM-IV diagnoses of rapid cycling bipolar I (RCBPDI) or II (RCBPDII) disorder, SUDs, and ADs including generalized anxiety disorder (GAD), panic disorder (PD), and obsessive-compulsive disorder (OCD). Data at the initial assessment of four studies was used to compare the prevalence differences in ADs between RCBPDI and RCBPDII by using protocol-defined SUD categories, “Never,” “Lifetime, but not recent,” or “Recent.” Results Five-hundred sixty-six of 568 patients (RCBPDI n=320, RCBPDII n=246) were eligible for analyses. In the “Never” group (n=191), patients with RCBPDI and RCBPDII had similar risk for ADs. In the “Lifetime, but not recent” group (n=195), RCBPDI patients had significantly higher risks for GAD (OR=3.29), PD (OR=2.95), but not OCD, compared with their RCBPDII counterparts. Similarly, in the “Recent” group (n=180), RCBPDI patients also had significantly higher risks for GAD (OR=3.6), PD (OR=3.8), but not OCD, compared with their RCBPDII counterparts. Limitations Data were cross-sectional and not all ADs were included. Conclusion In this large cohort of patients with rapid cycling bipolar disorder, risk for having GAD, PD, but not OCD increased significantly in patients with bipolar I disorder compared to their bipolar II counterparts when a history of SUD was present. However, there were no significant differences in the risk for GAD, PD, or OCD between the subtypes among patients without a history of SUD. PMID:18234350

NEPA, a fixed oral combination of netupitant and palonosetron, improves control of chemotherapy-induced nausea and vomiting (CINV) over multiple cycles of chemotherapy: results of a randomized, double-blind, phase 3 trial versus oral palonosetron.

PubMed

Aapro, Matti; Karthaus, Meinolf; Schwartzberg, Lee; Bondarenko, Igor; Sarosiek, Tomasz; Oprean, Cristina; Cardona-Huerta, Servando; Hansen, Vincent; Rossi, Giorgia; Rizzi, Giada; Borroni, Maria Elisa; Rugo, Hope

2017-04-01

Antiemetic guidelines recommend co-administration of targeted prophylactic medications inhibiting molecular pathways involved in emesis. NEPA is a fixed oral combination of a new NK 1 receptor antagonist (RA), netupitant (NETU 300 mg), and palonosetron (PALO 0.50 mg), a pharmacologically distinct 5-HT 3 RA. NEPA showed superior prevention of chemotherapy-induced nausea and vomiting (CINV) compared with oral PALO in a single chemotherapy cycle; maintenance of efficacy/safety over continuing cycles is the objective of this study. This study is a multinational, double-blind study comparing a single oral dose of NEPA vs oral PALO in chemotherapy-naïve patients receiving anthracycline/cyclophosphamide-based chemotherapy along with dexamethasone 12 mg (NEPA) or 20 mg (PALO) on day 1. The primary efficacy endpoint was delayed (25-120 h) complete response (CR: no emesis, no rescue medication) in cycle 1. Sustained efficacy was evaluated during the multicycle extension by calculating the proportion of patients with overall (0-120 h) CR in cycles 2-4 and by assessing the probability of sustained CR over multiple cycles. Of 1455 patients randomized, 1286 (88 %) participated in the multiple-cycle extension for a total of 5969 cycles; 76 % completed ≥4 cycles. The proportion of patients with an overall CR was significantly greater for NEPA than oral PALO for cycles 1-4 (74.3 vs 66.6 %, 80.3 vs 66.7 %, 83.8 vs 70.3 %, and 83.8 vs 74.6 %, respectively; p ≤ 0.001 each cycle). The cumulative percentage of patients with a sustained CR over all 4 cycles was also greater for NEPA (p < 0.0001). NEPA was well tolerated over cycles. NEPA, a convenient, guideline-consistent, fixed antiemetic combination is effective and safe over multiple cycles of chemotherapy.

78 FR 43870 - Hydrogen Energy California's Integrated Gasification Combined Cycle Project; Preliminary Staff...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-22

... Combined Cycle Project; Preliminary Staff Assessment and Draft Environmental Impact Statement AGENCY... Combined Cycle Project Preliminary Staff Assessment/Draft Environmental Impact Statement (PSA/DEIS) (DOE... Gasification Combined Cycle Project, which would be designed, constructed, and operated by HECA, LLC. HECA's...

Changes in Corticospinal and Spinal Excitability to the Biceps Brachii with a Neutral vs. Pronated Handgrip Position Differ between Arm Cycling and Tonic Elbow Flexion

PubMed Central

Forman, Davis A.; Richards, Mark; Forman, Garrick N.; Holmes, Michael W. R.; Power, Kevin E.

2016-01-01

The purpose of this study was to examine the influence of neutral and pronated handgrip positions on corticospinal excitability to the biceps brachii during arm cycling. Corticospinal and spinal excitability were assessed using motor evoked potentials (MEPs) elicited via transcranial magnetic stimulation (TMS) and cervicomedullary-evoked potentials (CMEPs) elicited via transmastoid electrical stimulation (TMES), respectively. Participants were seated upright in front on arm cycle ergometer. Responses were recorded from the biceps brachii at two different crank positions (6 and 12 o’clock positions relative to a clock face) while arm cycling with neutral and pronated handgrip positions. Responses were also elicited during tonic elbow flexion to compare/contrast the results to a non-rhythmic motor output. MEP and CMEP amplitudes were significantly larger at the 6 o’clock position while arm cycling with a neutral handgrip position compared to pronated (45.6 and 29.9%, respectively). There were no differences in MEP and CMEP amplitudes at the 12 o’clock position for either handgrip position. For the tonic contractions, MEPs were significantly larger with a neutral vs. pronated handgrip position (32.6% greater) while there were no difference in CMEPs. Corticospinal excitability was higher with a neutral handgrip position for both arm cycling and tonic elbow flexion. While spinal excitability was also higher with a neutral handgrip position during arm cycling, no difference was observed during tonic elbow flexion. These findings suggest that not only is corticospinal excitability to the biceps brachii modulated at both the supraspinal and spinal level, but that it is influenced differently between rhythmic arm cycling and tonic elbow flexion. PMID:27826236

Is It Important to Adapt Neoadjuvant Chemotherapy to the Visible Clinical Response? An Open Randomized Phase II Study Comparing Response-Guided and Standard Treatments in HER2-Negative Operable Breast Cancer

PubMed Central

Mouret-Reynier, Marie-Ange; Savoye, Aude-Marie; Abrial, Catherine; Kwiatkowski, Fabrice; Garbar, Christian; DuBray-Longeras, Pascale; Eymard, Jean-Christophe; Lebouedec, Guillaume; Vanpraagh, Isabelle; Penault-Llorca, Frederique; Chollet, Philippe; Cure, Hervé

2015-01-01

Background. Neoadjuvant treatment provides a unique opportunity to evaluate individual tumor sensitivity. This study evaluated whether a response-guided strategy could improve clinical outcome compared with a standard treatment. Methods. Overall, 264 previously untreated stage II–III operable breast cancer patients were randomized to receive either standard treatment (arm A, n = 131), consisting of fluorouracil, epirubicin, and cyclophosphamide (FEC100: 500, 100, and 500 mg/m2, respectively, for 3 cycles) followed by docetaxel (100 mg/m2 for 3 cycles), or adapted treatment (arm B, n = 133), beginning with 2 cycles of FEC100 and switching to docetaxel if tumor size decreased by <30% after 2 cycles or <50% after 4 cycles of FEC100 (ultrasound assessments according to World Health Organization criteria). Otherwise, FEC100 was given for six cycles before surgery. Intent-to-treat analysis was performed. Results. Similar results were observed for clinical response (objective response was 54% vs 56%, p = .18), breast conservation surgery (BCS; 67% vs 68%, p = .97), and pathological complete response rate (Chevallier classification: 14% vs 11%, p = .68; Statloff classification: 16% vs 13%, p = .82) between arms A and B. Similar toxicities were observed, even with unbalanced numbers of FEC100 and docetaxel courses. Conclusion. Adapted and standard treatments had similar results in terms of tumor response, BCS rate, and tolerability. Further survival outcome data are expected. PMID:25637380

Defect propagation in NiTi rotary instruments: a noncontact optical profilometry analysis.

PubMed

Barbosa, I; Ferreira, F; Scelza, P; Neff, J; Russano, D; Montagnana, M; Zaccaro Scelza, M

2018-04-10

To evaluate the presence and propagation of defects and their effects on surfaces of nickel-titanium (NiTi) instruments using noncontact, three-dimensional optical profilometry, and to assess the accuracy of this method of investigation. The flute surface areas of instruments from two commercial instrumentation systems, namely Reciproc R25 (n = 5) and WaveOne Primary (n = 5), were assessed and compared before and after performing two instrumentation cycles in simulated root canals in clear resin blocks. All the analyses were conducted on areas measuring 211 × 211 μm, located 3 mm from the tips of the instruments. A quantitative analysis was conducted before and after the first and second instrumentation cycles, using the Sa (average roughness over the measurement field), Sq (root mean square roughness) and Sz (average height over the measurement field) amplitude parameters. All the data were submitted to statistical analysis at a 5% level of significance. There was a significant increase (P = 0.007) in wear in both groups, especially between baseline and the second instrumentation cycle, with significantly higher wear values being observed on WaveOne instruments (Sz median values = 33.68 and 2.89 μm, respectively, for WO and RP groups). A significant increase in surface roughness (P = 0.016 and P = 0.008, respectively, for Sa and Sq) was observed in both groups from the first to the second instrumentation cycle, mostly in WaveOne specimens. Qualitative analysis revealed a greater number of defects on the flute topography of all the instruments after use. More defects were identified in WaveOne Primary instruments compared to Reciproc R25, irrespective of the evaluation stage. The investigation method provided an accurate, repeatable and reproducible assessment of NiTi instruments at different time-points. © 2018 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Life cycle assessment of integrated solid state anaerobic digestion and composting for on-farm organic residues treatment.

PubMed

Li, Yangyang; Manandhar, Ashish; Li, Guoxue; Shah, Ajay

2018-03-20

Driven by the gradual changes in the structure of energy consumption and improvements of living standards in China, the volume of on-farm organic solid waste is increasing. If untreated, these unutilized on-farm organic solid wastes can cause environmental problems. This paper presents the results of a life cycle assessment to compare the environmental impacts of different on-farm organic waste (which includes dairy manure, corn stover and tomato residue) treatment strategies, including anaerobic digestion (AD), composting, and AD followed by composting. The input life cycle inventory data are specific to China. The potential environmental impacts of different waste management strategies were assessed based on their acidification potential (AP), eutrophication potential (EP), global warming potential (GWP), ecotoxicity potential (ETP), and resource depletion (RD). The results show that the preferred treatment strategy for dairy manure is the one that integrated corn stover and tomato residue utilization and solid state AD technologies into the system. The GWP of integrated solid state AD and composting was the least, which is -2900 kg CO 2 eq/ t of dairy manure and approximately 14.8 times less than that of current status (i.e., liquid AD of dairy manure). Solid state AD of dairy manure, corn stover and tomato residues is the most favorable option in terms of AP, EP and ETP, which are more than 40% lower than that of the current status (i.e., AP: 3.11 kg SO 2 , EP: -0.94 kg N, and ETP: -881 CTUe (Comparative Toxic Units ecotoxicity)). The results also show that there is a significant potential for AP, EP, ETP, and GWP reduction, if AD is used prior to composting. The scenario analysis for transportation distance showed that locating the AD plant and composting facility on the farm was advantageous in terms of all the life cycle impact categories. Copyright © 2018 Elsevier Ltd. All rights reserved.

DNA Damage, Cell Cycle Arrest, and Apoptosis Induction Caused by Lead in Human Leukemia Cells

PubMed Central

Yedjou, Clement G.; Tchounwou, Hervey M.; Tchounwou, Paul B.

2015-01-01

In recent years, the industrial use of lead has been significantly reduced from paints and ceramic products, caulking, and pipe solder. Despite this progress, lead exposure continues to be a significant public health concern. The main goal of this research was to determine the in vitro mechanisms of lead nitrate [Pb(NO3)2] to induce DNA damage, apoptosis, and cell cycle arrest in human leukemia (HL-60) cells. To reach our goal, HL-60 cells were treated with different concentrations of Pb(NO3)2 for 24 h. Live cells and necrotic death cells were measured by the propidium idiode (PI) assay using the cellometer vision. Cell apoptosis was measured by the flow cytometry and DNA laddering. Cell cycle analysis was evaluated by the flow cytometry. The result of the PI demonstrated a significant (p < 0.05) increase of necrotic cell death in Pb(NO3)2-treated cells, indicative of membrane rupture by Pb(NO3)2 compared to the control. Data generated from the comet assay indicated a concentration-dependent increase in DNA damage, showing a significant increase (p < 0.05) in comet tail-length and percentages of DNA cleavage. Data generated from the flow cytometry assessment indicated that Pb(NO3)2 exposure significantly (p < 0.05) increased the proportion of caspase-3 positive cells (apoptotic cells) compared to the control. The flow cytometry assessment also indicated Pb(NO3)2 exposure caused cell cycle arrest at the G0/G1 checkpoint. The result of DNA laddering assay showed presence of DNA smear in the agarose gel with little presence of DNA fragments in the treated cells compared to the control. In summary, Pb(NO3)2 inhibits HL-60 cells proliferation by not only inducing DNA damage and cell cycle arrest at the G0/G1 checkpoint but also triggering the apoptosis through caspase-3 activation and nucleosomal DNA fragmentation accompanied by secondary necrosis. We believe that our study provides a new insight into the mechanisms of Pb(NO3)2 exposure and its associated adverse health effects. PMID:26703663

Muscle Performance Investigated With a Novel Smart Compression Garment Based on Pressure Sensor Force Myography and Its Validation Against EMG.

PubMed

Belbasis, Aaron; Fuss, Franz Konstantin

2018-01-01

Muscle activity and fatigue performance parameters were obtained and compared between both a smart compression garment and the gold-standard, a surface electromyography (EMG) system during high-speed cycling in seven participants. The smart compression garment, based on force myography (FMG), comprised of integrated pressure sensors that were sandwiched between skin and garment, located on five thigh muscles. The muscle activity was assessed by means of crank cycle diagrams (polar plots) that displayed the muscle activity relative to the crank cycle. The fatigue was assessed by means of the median frequency of the power spectrum of the EMG signal; the fractal dimension (FD) of the EMG signal; and the FD of the pressure signal. The smart compression garment returned performance parameters (muscle activity and fatigue) comparable to the surface EMG. The major differences were that the EMG measured the electrical activity, whereas the pressure sensor measured the mechanical activity. As such, there was a phase shift between electrical and mechanical signals, with the electrical signals preceding the mechanical counterparts in most cases. This is specifically pronounced in high-speed cycling. The fatigue trend over the duration of the cycling exercise was clearly reflected in the fatigue parameters (FDs and median frequency) obtained from pressure and EMG signals. The fatigue parameter of the pressure signal (FD) showed a higher time dependency ( R 2 = 0.84) compared to the EMG signal. This reflects that the pressure signal puts more emphasis on the fatigue as a function of time rather than on the origin of fatigue (e.g., peripheral or central fatigue). In light of the high-speed activity results, caution should be exerted when using data obtained from EMG for biomechanical models. In contrast to EMG data, activity data obtained from FMG are considered more appropriate and accurate as an input for biomechanical modeling as they truly reflect the mechanical muscle activity. In summary, the smart compression garment based on FMG is a valid alternative to EMG-garments and provides more accurate results at high-speed activity (avoiding the electro-mechanical delay), as well as clearly measures the progress of muscle fatigue over time.

Muscle Performance Investigated With a Novel Smart Compression Garment Based on Pressure Sensor Force Myography and Its Validation Against EMG

PubMed Central

Belbasis, Aaron; Fuss, Franz Konstantin

2018-01-01

Muscle activity and fatigue performance parameters were obtained and compared between both a smart compression garment and the gold-standard, a surface electromyography (EMG) system during high-speed cycling in seven participants. The smart compression garment, based on force myography (FMG), comprised of integrated pressure sensors that were sandwiched between skin and garment, located on five thigh muscles. The muscle activity was assessed by means of crank cycle diagrams (polar plots) that displayed the muscle activity relative to the crank cycle. The fatigue was assessed by means of the median frequency of the power spectrum of the EMG signal; the fractal dimension (FD) of the EMG signal; and the FD of the pressure signal. The smart compression garment returned performance parameters (muscle activity and fatigue) comparable to the surface EMG. The major differences were that the EMG measured the electrical activity, whereas the pressure sensor measured the mechanical activity. As such, there was a phase shift between electrical and mechanical signals, with the electrical signals preceding the mechanical counterparts in most cases. This is specifically pronounced in high-speed cycling. The fatigue trend over the duration of the cycling exercise was clearly reflected in the fatigue parameters (FDs and median frequency) obtained from pressure and EMG signals. The fatigue parameter of the pressure signal (FD) showed a higher time dependency (R2 = 0.84) compared to the EMG signal. This reflects that the pressure signal puts more emphasis on the fatigue as a function of time rather than on the origin of fatigue (e.g., peripheral or central fatigue). In light of the high-speed activity results, caution should be exerted when using data obtained from EMG for biomechanical models. In contrast to EMG data, activity data obtained from FMG are considered more appropriate and accurate as an input for biomechanical modeling as they truly reflect the mechanical muscle activity. In summary, the smart compression garment based on FMG is a valid alternative to EMG-garments and provides more accurate results at high-speed activity (avoiding the electro-mechanical delay), as well as clearly measures the progress of muscle fatigue over time. PMID:29725306

DNA Damage, Cell Cycle Arrest, and Apoptosis Induction Caused by Lead in Human Leukemia Cells.

PubMed

Yedjou, Clement G; Tchounwou, Hervey M; Tchounwou, Paul B

2015-12-22

In recent years, the industrial use of lead has been significantly reduced from paints and ceramic products, caulking, and pipe solder. Despite this progress, lead exposure continues to be a significant public health concern. The main goal of this research was to determine the in vitro mechanisms of lead nitrate [Pb(NO₃)₂] to induce DNA damage, apoptosis, and cell cycle arrest in human leukemia (HL-60) cells. To reach our goal, HL-60 cells were treated with different concentrations of Pb(NO₃)₂ for 24 h. Live cells and necrotic death cells were measured by the propidium idiode (PI) assay using the cellometer vision. Cell apoptosis was measured by the flow cytometry and DNA laddering. Cell cycle analysis was evaluated by the flow cytometry. The result of the PI demonstrated a significant (p < 0.05) increase of necrotic cell death in Pb(NO₃)₂-treated cells, indicative of membrane rupture by Pb(NO₃)₂ compared to the control. Data generated from the comet assay indicated a concentration-dependent increase in DNA damage, showing a significant increase (p < 0.05) in comet tail-length and percentages of DNA cleavage. Data generated from the flow cytometry assessment indicated that Pb(NO₃)₂ exposure significantly (p < 0.05) increased the proportion of caspase-3 positive cells (apoptotic cells) compared to the control. The flow cytometry assessment also indicated Pb(NO₃)₂ exposure caused cell cycle arrest at the G₀/G₁ checkpoint. The result of DNA laddering assay showed presence of DNA smear in the agarose gel with little presence of DNA fragments in the treated cells compared to the control. In summary, Pb(NO₃)₂ inhibits HL-60 cells proliferation by not only inducing DNA damage and cell cycle arrest at the G₀/G₁ checkpoint but also triggering the apoptosis through caspase-3 activation and nucleosomal DNA fragmentation accompanied by secondary necrosis. We believe that our study provides a new insight into the mechanisms of Pb(NO₃)₂ exposure and its associated adverse health effects.

LCIA framework and cross-cutting issues guidance within the UNEP/SETAC Life Cycle Initiative

EPA Science Inventory

Increasing needs for decision support and advances in scientific knowledge within life cycle assessment (LCA) led to substantial efforts to provide global guidance on environmental life cycle impact assessment (LCIA) indicators under the auspices of the UNEP-SETAC Life Cycle Init...

Identifying built environmental patterns using cluster analysis and GIS: relationships with walking, cycling and body mass index in French adults.

PubMed

Charreire, Hélène; Weber, Christiane; Chaix, Basile; Salze, Paul; Casey, Romain; Banos, Arnaud; Badariotti, Dominique; Kesse-Guyot, Emmanuelle; Hercberg, Serge; Simon, Chantal; Oppert, Jean-Michel

2012-05-23

Socio-ecological models suggest that both individual and neighborhood characteristics contribute to facilitating health-enhancing behaviors such as physical activity. Few European studies have explored relationships between local built environmental characteristics, recreational walking and cycling and weight status in adults. The aim of this study was to identify built environmental patterns in a French urban context and to assess associations with recreational walking and cycling behaviors as performed by middle-aged adult residents. We used a two-step procedure based on cluster analysis to identify built environmental patterns in the region surrounding Paris, France, using measures derived from Geographic Information Systems databases on green spaces, proximity facilities (destinations) and cycle paths. Individual data were obtained from participants in the SU.VI.MAX cohort; 1,309 participants residing in the Ile-de-France in 2007 were included in this analysis. Associations between built environment patterns, leisure walking/cycling data (h/week) and measured weight status were assessed using multinomial logistic regression with adjustment for individual and neighborhood characteristics. Based on accessibility to green spaces, proximity facilities and availability of cycle paths, seven built environmental patterns were identified. The geographic distribution of built environmental patterns in the Ile-de-France showed that a pattern characterized by poor spatial accessibility to green spaces and proximity facilities and an absence of cycle paths was found only in neighborhoods in the outer suburbs, whereas patterns characterized by better spatial accessibility to green spaces, proximity facilities and cycle paths were more evenly distributed across the region. Compared to the reference pattern (poor accessibility to green areas and facilities, absence of cycle paths), subjects residing in neighborhoods characterized by high accessibility to green areas and local facilities and by a high density of cycle paths were more likely to walk/cycle, after adjustment for individual and neighborhood sociodemographic characteristics (OR = 2.5 95%CI 1.4-4.6). Body mass index did not differ across patterns. Built environmental patterns were associated with walking and cycling among French adults. These analyses may be useful in determining urban and public health policies aimed at promoting a healthy lifestyle.

Effect of Repeated Freeze-Thaw Cycles on Beef Quality and Safety

PubMed Central

Rahman, Mohammad Hafizur; Hossain, Mohammad Mujaffar; Rahman, Syed Mohammad Ehsanur; Hashem, Mohammad Abul

2014-01-01

The objectives of this study were to know the effect of repeated freeze-thaw cycles of beef on the sensory, physicochemical quality and microbiological assessment. The effects of three successive freeze-thaw cycles on beef forelimb were investigated comparing with unfrozen fresh beef for 75 d by keeping at −20±1℃. The freeze-thaw cycles were subjected to three thawing methods and carried out to know the best one. As the number of freeze-thaw cycles increased color and odor declined significantly before cook within the cycles and tenderness, overall acceptability also declined among the cycles after cook by thawing methods. The thawing loss increased and dripping loss decreased significantly (p<0.05). Water holding capacity (WHC) increased (p<0.05) until two cycles and then decreased. Cooking loss increased in cycle 1 and 3, but decreased in cycle 2. pH decreased significantly (p<0.05) among the cycles. Moreover, drip loss, cooking loss and WHC were affected (p<0.05) by thawing methods within the cycles. 2-Thiobarbituric acid (TBARS) value increased (p<0.05) gradually within the cycles and among the cycles by thawing methods. Total viable bacteria, total coliform and total yeast-mould count decreased significantly (p<0.05) within and among the cycles in comparison to the initial count in repeated freeze-thaw cycles. As a result, repeated freeze-thaw cycles affected the sensory, physicochemical and microbiological qua- lity of beef, causing the deterioration of beef quality, but improved the microbiological quality. Although repeated freeze-thaw cycles did not affect much on beef quality and safety but it may be concluded that repeated freeze and thaw should be minimized in terms of beef color for commercial value and WHC and tenderness/juiciness for eating quality. PMID:26761286

Environmental impact assessment of european non-ferro mining industries through life-cycle assessment

NASA Astrophysics Data System (ADS)

Hisan Farjana, Shahjadi; Huda, Nazmul; Parvez Mahmud, M. A.

2018-05-01

European mining industries are the vast industrial sector which contributes largely on their economy which constitutes of ferro and non-ferro metals and minerals industries. The non-ferro metals extraction and processing industries require focus of attention due to sustainability concerns as their manufacturing processes are highly energy intensive and impacts globally on environment. This paper analyses major environmental effects caused by European metal industries based on the life-cycle impact analysis technologies. This research work is the first work in considering the comparative environmental impact analysis of European non-ferro metal industries which will reveal their technological similarities and dissimilarities to assess their environmental loads. The life-cycle inventory datasets are collected from the EcoInvent database while the analysis is done using the CML baseline and ReCipe endpoint method using SimaPro software version 8.4. The CML and ReCipe method are chosen because they are specialized impact assessment methods for European continent. The impact categories outlined for discussion here are human health, global warming and ecotoxicity. The analysis results reveal that the gold industry is vulnerable for the environment due to waste emission and similar result retained by silver mines a little bit. But copper, lead, manganese and zinc mining processes and industries are environment friendly in terms of metal extraction technologies and waste emissions.

Modelling of environmental impacts of solid waste landfilling within the life-cycle analysis program EASEWASTE.

PubMed

Kirkeby, Janus T; Birgisdottir, Harpa; Bhander, Gurbakash Singh; Hauschild, Michael; Christensen, Thomas H

2007-01-01

A new computer-based life-cycle assessment model (EASEWASTE) has been developed to evaluate resource and environmental consequences of solid waste management systems. This paper describes the landfilling sub-model used in the life-cycle assessment program EASEWASTE, and examines some of the implications of this sub-model. All quantities and concentrations of leachate and landfill gas can be modified by the user in order to bring them in agreement with the actual landfill that is assessed by the model. All emissions, except the generation of landfill gas, are process specific. The landfill gas generation is calculated on the basis of organic matter in the landfilled waste. A landfill assessment example is provided. For this example, the normalised environmental effects of landfill gas on global warming and photochemical smog are much greater than the environmental effects for landfill leachate or for landfill construction. A sensitivity analysis for this example indicates that the overall environmental impact is sensitive to the gas collection efficiency and the use of the gas, but not to the amount of leachate generated, or the amount of soil or liner material used in construction. The landfill model can be used for evaluating different technologies with different liners, gas and leachate collection efficiencies, and to compare the environmental consequences of landfilling with alternative waste treatment options such as incineration or anaerobic digestion.

A modular Human Exposure Model (HEM) framework to ...

EPA Pesticide Factsheets

Life Cycle Impact Analysis (LCIA) has proven to be a valuable tool for systematically comparing processes and products, and has been proposed for use in Chemical Alternatives Analysis (CAA). The exposure assessment portion of the human health impact scores of LCIA has historically focused on far-field sources (environmentally mediated exposures) while research has shown that use related exposures, (near-field exposures) typically dominate population exposure. Characterizing the human health impacts of chemicals in consumer products over the life cycle of these products requires an evaluation of both near-field as well far-field sources. Assessing the impacts of the near-field exposures requires bridging the scientific and technical gaps that currently prevent the harmonious use of the best available methods and tools from the fields of LCIA and human health exposure and risk assessment. The U.S. EPA’s Chemical Safety and Sustainability LC-HEM project is developing the Human Exposure Model (HEM) to assess near-field exposures to chemicals that occur to various populations over the life cycle of a commercial product. The HEM will be a publically available, web-based, modular system which will allow for the evaluation of chemical/product impacts in a LCIA framework to support CAA. We present here an overview of the framework for the modular HEM system. The framework includes a data flow diagram of in-progress and future planned modules, the definition of each mod

7 CFR 3560.65 - Reserve account.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-year period. The reserve account analysis is based on either a Capital Needs Assessment or life cycle... Assessment or as part of the original life cycle cost analysis. The cost of conducting either a Capital Needs... Needs Assessment or life cycle cost analysis may be included in the loan financing. (b) For ownership...

7 CFR 3560.65 - Reserve account.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-year period. The reserve account analysis is based on either a Capital Needs Assessment or life cycle... Assessment or as part of the original life cycle cost analysis. The cost of conducting either a Capital Needs... Needs Assessment or life cycle cost analysis may be included in the loan financing. (b) For ownership...

Life cycle assessment of a parabolic trough concentrating solar power plant and the impacts of key design alternatives.

PubMed

Burkhardt, John J; Heath, Garvin A; Turchi, Craig S

2011-03-15

Climate change and water scarcity are important issues for today's power sector. To inform capacity expansion decisions, hybrid life cycle assessment is used to evaluate a reference design of a parabolic trough concentrating solar power (CSP) facility located in Daggett, CA, along four sustainability metrics: life cycle (LC) greenhouse gas (GHG) emissions, water consumption, cumulative energy demand (CED), and energy payback time (EPBT). This wet-cooled, 103 MW plant utilizes mined nitrates salts in its two-tank, thermal energy storage (TES) system. Design alternatives of dry-cooling, a thermocline TES, and synthetically derived nitrate salt are evaluated. During its LC, the reference CSP plant is estimated to emit 26 g of CO(2eq) per kWh, consume 4.7 L/kWh of water, and demand 0.40 MJ(eq)/kWh of energy, resulting in an EPBT of approximately 1 year. The dry-cooled alternative is estimated to reduce LC water consumption by 77% but increase LC GHG emissions and CED by 8%. Synthetic nitrate salts may increase LC GHG emissions by 52% compared to mined. Switching from two-tank to thermocline TES configuration reduces LC GHG emissions, most significantly for plants using synthetically derived nitrate salts. CSP can significantly reduce GHG emissions compared to fossil-fueled generation; however, dry-cooling may be required in many locations to minimize water consumption.

Comparative health and safety assessment of the SPS and alternative electrical generation systems

NASA Astrophysics Data System (ADS)

Habegger, L. J.; Gasper, J. R.; Brown, C. D.

1980-07-01

A comparative analysis of health and safety risks is presented for the Satellite Power System and five alternative baseload electrical generation systems: a low-Btu coal gasification system with an open-cycle gas turbine combined with a steam topping cycle; a light water fission reactor system without fuel reprocessing; a liquid metal fast breeder fission reactor system; a central station terrestrial photovoltaic system; and a first generation fusion system with magnetic confinement. For comparison, risk from a decentralized roof-top photovoltaic system with battery storage is also evaluated. Quantified estimates of public and occupational risks within ranges of uncertainty were developed for each phase of the energy system. The potential significance of related major health and safety issues that remain unquantitied are also discussed.

Comparative health and safety assessment of the SPS and alternative electrical generation systems

NASA Technical Reports Server (NTRS)

Habegger, L. J.; Gasper, J. R.; Brown, C. D.

1980-01-01

A comparative analysis of health and safety risks is presented for the Satellite Power System and five alternative baseload electrical generation systems: a low-Btu coal gasification system with an open-cycle gas turbine combined with a steam topping cycle; a light water fission reactor system without fuel reprocessing; a liquid metal fast breeder fission reactor system; a central station terrestrial photovoltaic system; and a first generation fusion system with magnetic confinement. For comparison, risk from a decentralized roof-top photovoltaic system with battery storage is also evaluated. Quantified estimates of public and occupational risks within ranges of uncertainty were developed for each phase of the energy system. The potential significance of related major health and safety issues that remain unquantitied are also discussed.

Life cycle assessment: Existing building retrofit versus replacement

NASA Astrophysics Data System (ADS)

Darabi, Nura

The embodied energy in building materials constitutes a large part of the total energy required for any building (Thormark 2001, 429). In working to make buildings more energy efficient this needs to be considered. Integrating considerations about life cycle assessment for buildings and materials is one promising way to reduce the amount of energy consumption being used within the building sector and the environmental impacts associated with that energy. A life cycle assessment (LCA) model can be utilized to help evaluate the embodied energy in building materials in comparison to the buildings operational energy. This thesis takes into consideration the potential life cycle reductions in energy and CO2 emissions that can be made through an energy retrofit of an existing building verses demolition and replacement with a new energy efficient building. A 95,000 square foot institutional building built in the 1960`s was used as a case study for a building LCA, along with a calibrated energy model of the existing building created as part of a previous Masters of Building Science thesis. The chosen case study building was compared to 10 possible improvement options of either energy retrofit or replacement of the existing building with a higher energy performing building in order to see the life cycle relationship between embodied energy, operational energy, and C02 emissions. As a result of completing the LCA, it is shown under which scenarios building retrofit saves more energy over the lifespan of the building than replacement with new construction. It was calculated that energy retrofit of the chosen existing institutional building would reduce the amount of energy and C02 emissions associated with that building over its life span.

Life cycle assessment of Mexican polymer and high-durability cotton paper banknotes.

PubMed

Luján-Ornelas, Cristina; Mancebo Del C Sternenfels, Uriel; Güereca, Leonor Patricia

2018-07-15

This study compares the environmental performance of Mexican banknotes printed on high-durability cotton paper (HD paper) and thermoplastic polymer (polymer) through a life cycle assessment to appraise the environmental impacts from the extraction of raw materials to the final disposal of the banknotes. The functional unit was defined considering the next parameters: 1) lifespan of the banknotes, stablished in 31.5 and 54months for HD paper and polymer, respectively; 2) denomination, selecting $200 pesos banknotes; 3) a 5year time frame and 4) a defined amount of money, in this case stablished as the monthly cash supply of an average Mexican household, equaling $12,708 pesos. Accordingly, 121 pieces for the HD paper and 71 pieces for the polymer banknotes were analyzed. The results favor the banknotes printed on polymer substrate primarily because of the longer lifespan of this type of material; however, there is a considerable environmental impact in the stages of distribution, followed by the extraction of the raw materials (crude oil) during manufacturing. Regarding the HD cotton paper, the major impact corresponds to extraction of the raw materials, followed by the distribution of the banknotes. The inclusion of the automatic teller machines (ATMs) in the life cycle assessment of banknotes shows that the electricity required by these devices became the largest contributor to the environmental impacts. Additionally, the sensitivity analysis that the average lifetime of the banknotes is a determining factor for the environmental impacts associated with the whole life cycle of this product. The life cycle stages that refer to the extraction of the raw materials, combined with the average lifetime of the banknotes and the electricity required during the usage stage, are determining factors in the total environmental impact associated with Mexican banknotes. Copyright © 2018 Elsevier B.V. All rights reserved.

Cycling infrastructure for reducing cycling injuries in cyclists.

PubMed

Mulvaney, Caroline A; Smith, Sherie; Watson, Michael C; Parkin, John; Coupland, Carol; Miller, Philip; Kendrick, Denise; McClintock, Hugh

2015-12-10

Cycling is an attractive form of transport. It is beneficial to the individual as a form of physical activity that may fit more readily into an individual's daily routine, such as for cycling to work and to the shops, than other physical activities such as visiting a gym. Cycling is also beneficial to the wider community and the environment as a result of fewer motorised journeys. Cyclists are seen as vulnerable road users who are frequently in close proximity to larger and faster motorised vehicles. Cycling infrastructure aims to make cycling both more convenient and safer for cyclists. This review is needed to guide transport planning. To:1. evaluate the effects of different types of cycling infrastructure on reducing cycling injuries in cyclists, by type of infrastructure;2. evaluate the effects of cycling infrastructure on reducing the severity of cycling injuries in cyclists;3. evaluate the effects of cycling infrastructure on reducing cycling injuries in cyclists with respect to age, sex and social group. We ran the most recent search on 2nd March 2015. We searched the Cochrane Injuries Group Specialised Register, CENTRAL (The Cochrane Library), MEDLINE (OvidSP), Embase Classic + Embase(OvidSP), PubMed and 10 other databases. We searched websites, handsearched conference proceedings, screened reference lists of included studies and previously published reviews and contacted relevant organisations. We included randomised controlled trials, cluster randomised controlled trials, controlled before-after studies, and interrupted time series studies which evaluated the effect of cycling infrastructure (such as cycle lanes, tracks or paths, speed management, roundabout design) on cyclist injury or collision rates. Studies had to include a comparator, that is, either no infrastructure or a different type of infrastructure. We excluded studies that assessed collisions that occurred as a result of competitive cycling. Two review authors examined the titles and abstracts of papers obtained from searches to determine eligibility. Two review authors extracted data from the included trials and assessed the risk of bias. We carried out a meta-analysis using the random-effects model where at least three studies reported the same intervention and outcome. Where there were sufficient studies, as a secondary analysis we accounted for changes in cyclist exposure in the calculation of the rate ratios. We rated the quality of the evidence as 'high', 'moderate', 'low' or 'very low' according to the GRADE approach for the installation of cycle routes and networks. We identified 21 studies for inclusion in the review: 20 controlled before-after (CBA) studies and one interrupted time series (ITS) study. These evaluated a range of infrastructure including cycle lanes, advanced stop lines, use of colour, cycle tracks, cycle paths, management of the road network, speed management, cycle routes and networks, roundabout design and packages of measures. No studies reported medically-attended or self-reported injuries. There was no evidence that cycle lanes reduce the rate of cycle collisions (rate ratio 1.21, 95% CI 0.70 to 2.08). Taking into account cycle flow, there was no difference in collisions for cyclists using cycle routes and networks compared with cyclists not using cycle routes and networks (RR 0.40, 95% CI 0.15 to 1.05). There was statistically significant heterogeneity between the studies (I² = 75%, Chi² = 8.00 df = 2, P = 0.02) for the analysis adjusted for cycle flow. We judged the quality of the evidence regarding cycle routes and networks as very low and we are very uncertain about the estimate. These analyses are based on findings from CBA studies.From data presented narratively, the use of 20 mph speed restrictions in urban areas may be effective at reducing cyclist collisions. Redesigning specific parts of cycle routes that may be particularly busy or complex in terms of traffic movement may be beneficial to cyclists in terms of reducing the risk of collision. Generally, the conversion of intersections to roundabouts may increase the number of cycle collisions. In particular, the conversion of intersections to roundabouts with cycle lanes marked as part of the circulating carriageway increased cycle collisions. However, the conversion of intersections with and without signals to roundabouts with cycle paths may reduce the odds of collision. Both continuing a cycle lane across the mouth of a side road with a give way line onto the main road, and cycle tracks, may increase the risk of injury collisions in cyclists. However, these conclusions are uncertain, being based on a narrative review of findings from included studies. There is a lack of evidence that cycle paths or advanced stop lines either reduce or increase injury collisions in cyclists. There is also insufficient evidence to draw any robust conclusions concerning the effect of cycling infrastructure on cycling collisions in terms of severity of injury, sex, age, and level of social deprivation of the casualty.In terms of quality of the evidence, there was little matching of intervention and control sites. In many studies, the comparability of the control area to the intervention site was unclear and few studies provided information on other cycling infrastructures that may be in place in the control and intervention areas. The majority of studies analysed data routinely collected by organisations external to the study team, thus reducing the risk of bias in terms of systematic differences in assessing outcomes between the control and intervention groups. Some authors did not take regression-to-mean effects into account when examining changes in collisions. Longer data collection periods pre- and post-installation would allow for regression-to-mean effects and also seasonal and time trends in traffic volume to be observed. Few studies adjusted cycle collision rates for exposure. Generally, there is a lack of high quality evidence to be able to draw firm conclusions as to the effect of cycling infrastructure on cycling collisions. There is a lack of rigorous evaluation of cycling infrastructure.

RGC-32 is a novel regulator of the T-lymphocyte cell cycle.

PubMed

Tegla, Cosmin A; Cudrici, Cornelia D; Nguyen, Vinh; Danoff, Jacob; Kruszewski, Adam M; Boodhoo, Dallas; Mekala, Armugam P; Vlaicu, Sonia I; Chen, Ching; Rus, Violeta; Badea, Tudor C; Rus, Horea

2015-06-01

We have previously shown that RGC-32 is involved in cell cycle regulation in vitro. To define the in vivo role of RGC-32, we generated RGC-32 knockout mice. These mice developed normally and did not spontaneously develop overt tumors. To assess the effect of RGC-32 deficiency on cell cycle activation in T cells, we determined the proliferative rates of CD4(+) and CD8(+) T cells from the spleens of RGC-32(-/-) mice, as compared to wild-type (WT, RGC-32(+/+)) control mice. After stimulation with anti-CD3/anti-CD28, CD4(+) T cells from RGC-32(-/-) mice displayed a significant increase in [(3)H]-thymidine incorporation when compared to WT mice. In addition, both CD4(+) and CD8(+) T cells from RGC-32(-/-) mice displayed a significant increase in the proportion of proliferating Ki67(+) cells, indicating that in T cells, RGC-32 has an inhibitory effect on cell cycle activation induced by T-cell receptor/CD28 engagement. Furthermore, Akt and FOXO1 phosphorylation induced in stimulated CD4(+) T-cells from RGC-32(-/-) mice were significantly higher, indicating that RGC-32 inhibits cell cycle activation by suppressing FOXO1 activation. We also found that IL-2 mRNA and protein expression were significantly increased in RGC-32(-/-) CD4(+) T cells when compared to RGC-32(+/+) CD4(+) T cells. In addition, the effect of RGC-32 on the cell cycle and IL-2 expression was inhibited by pretreatment of the samples with LY294002, indicating a role for phosphatidylinositol 3-kinase (PI3K). Thus, RGC-32 is involved in controlling the cell cycle of T cells in vivo, and this effect is mediated by IL-2 in a PI3K-dependent fashion. Copyright © 2015 Elsevier Inc. All rights reserved.

An analysis of international nuclear fuel supply options

NASA Astrophysics Data System (ADS)

Taylor, J'tia Patrice

As the global demand for energy grows, many nations are considering developing or increasing nuclear capacity as a viable, long-term power source. To assess the possible expansion of nuclear power and the intricate relationships---which cover the range of economics, security, and material supply and demand---between established and aspirant nuclear generating entities requires models and system analysis tools that integrate all aspects of the nuclear enterprise. Computational tools and methods now exist across diverse research areas, such as operations research and nuclear engineering, to develop such a tool. This dissertation aims to develop methodologies and employ and expand on existing sources to develop a multipurpose tool to analyze international nuclear fuel supply options. The dissertation is comprised of two distinct components: the development of the Material, Economics, and Proliferation Assessment Tool (MEPAT), and analysis of fuel cycle scenarios using the tool. Development of MEPAT is aimed for unrestricted distribution and therefore uses publicly available and open-source codes in its development when possible. MEPAT is built using the Powersim Studio platform that is widely used in systems analysis. MEPAT development is divided into three modules focusing on: material movement; nonproliferation; and economics. The material movement module tracks material quantity in each process of the fuel cycle and in each nuclear program with respect to ownership, location and composition. The material movement module builds on techniques employed by fuel cycle models such as the Verifiable Fuel Cycle Simulation (VISION) code developed at the Idaho National Laboratory under the Advanced Fuel Cycle Initiative (AFCI) for the analysis of domestic fuel cycle. Material movement parameters such as lending and reactor preference, as well as fuel cycle parameters such as process times and material factors are user-specified through a Microsoft Excel(c) data spreadsheet. The material movement module is the largest of the three, and the two other modules that assess nonproliferation and economics of the options are dependent on its output. Proliferation resistance measures from literature are modified and incorporated in MEPAT. The module to assess the nonproliferation of the supply options allows the user to specify defining attributes for the fuel cycle processes, and determines significant quantities of materials as well as measures of proliferation resistance. The measure is dependent on user-input and material information. The economics module allows the user to specify costs associated with different processes and other aspects of the fuel cycle. The simulation tool then calculates economic measures that relate the cost of the fuel cycle to electricity production. The second part of this dissertation consists of an examination of four scenarios of fuel supply option using MEPAT. The first is a simple scenario illustrating the modules and basic functions of MEPAT. The second scenario recreates a fuel supply study reported earlier in literature, and compares MEPAT results with those reported earlier for validation. The third, and a rather realistic, scenario includes four nuclear programs with one program entering the nuclear energy market. The fourth scenario assesses the reactor options available to the Hashemite Kingdom of Jordan, which is currently assessing available options to introduce nuclear power in the country. The methodology developed and implemented in MEPAT to analyze the material, proliferation and economics of nuclear fuel supply options is expected to help simplify and assess different reactor and fuel options available to utilities, government agencies and international organizations.

Ideal cycle analysis of a regenerative pulse detonation engine for power production

NASA Astrophysics Data System (ADS)

Bellini, Rafaela

Over the last few decades, considerable research has been focused on pulse detonation engines (PDEs) as a promising replacement for existing propulsion systems with potential applications in aircraft ranging from the subsonic to the lower hypersonic regimes. On the other hand, very little attention has been given to applying detonation for electric power production. One method for assessing the performance of a PDE is through thermodynamic cycle analysis. Earlier works have adopted a thermodynamic cycle for the PDE that was based on the assumption that the detonation process could be approximated by a constant volume process, called the Humphrey cycle. The Fickett-Jacob cycle, which uses the one--dimensional Chapman--Jouguet (CJ) theory of detonation, has also been used to model the PDE cycle. However, an ideal PDE cycle must include a detonation based compression and heat release processes with a finite chemical reaction rate that is accounted for in the Zeldovich -- von Neumann -- Doring model of detonation where the shock is considered a discontinuous jump and is followed by a finite exothermic reaction zone. This work presents a thermodynamic cycle analysis for an ideal PDE cycle for power production. A code has been written that takes only one input value, namely the heat of reaction of a fuel-oxidizer mixture, based on which the program computes all the points on the ZND cycle (both p--v and T--s plots), including the von Neumann spike and the CJ point along with all the non-dimensionalized state properties at each point. In addition, the program computes the points on the Humphrey and Brayton cycles for the same input value. Thus, the thermal efficiencies of the various cycles can be calculated and compared. The heat release of combustion is presented in a generic form to make the program usable with a wide variety of fuels and oxidizers and also allows for its use in a system for the real time monitoring and control of a PDE in which the heat of reaction can be obtained as a function of fuel-oxidizer ratio. The Humphrey and ZND cycles are studied in comparison with the Brayton cycle for different fuel-air mixtures such as methane, propane and hydrogen. The validity and limitations of the ZND and Humphrey cycles related to the detonation process are discussed and the criteria for the selection of the best model for the PDE cycle are explained. It is seen that the ZND cycle is a more appropriate representation of the PDE cycle. Next, the thermal and electrical power generation efficiencies for the PDE are compared with those of the deflagration based Brayton cycle. While the Brayton cycle shows an efficiency of 0 at a compressor pressure ratio of 1, the thermal efficiency for the ZND cycle starts out at 42% for hydrogen--air and then climbs to a peak of 66% at a compression ratio of 7 before falling slowly for higher compression ratios. The Brayton cycle efficiency rises above the PDEs for compression ratios above 23. This finding supports the theoretical advantage of PDEs over the gas turbines because PDEs only require a fan or only a few compressor stages, thereby eliminating the need for heavy compressor machinery, making the PDEs less complex and therefore more cost effective than other engines. Lastly, a regeneration study is presented to analyze how the use of exhaust gases can improve the performance of the system. The thermal efficiencies for the regenerative ZND cycle are compared with the efficiencies for the non--regenerative cycle. For a hydrogen--air mixture the thermal efficiency increases from 52%, for a cycle without regeneration, to 78%, for the regenerative cycle. The efficiency is compared with the Carnot efficiency of 84% which is the maximum possible theoretical efficiency of the cycle. When compared to the Brayton cycle thermal efficiencies, the regenerative cycle shows efficiencies that are always higher for the pressure ratio studied of 5 ≤ pic ≤ 25, where pi c the compressor pressure ratio of the cycle. This observation strengthens the idea of using regeneration on PDEs.

Oral contraceptives positively affect mood in healthy PMS-free women: A longitudinal study.

PubMed

Hamstra, Danielle A; de Kloet, E Ronald; de Rover, Mischa; Van der Does, Willem

2017-12-01

Menstrual cycle phase and oral contraceptives (OC) use influence mood and cognition and these effects may be moderated by the mineralocorticoid receptor (MR) genotype. The effect of menstrual cycle phase on mood may be increased if participants know that this is the focus of study. We assessed aspects associated with reproductive depression such as mood, interpersonal sensitivity, affect lability and depressive cognitions in MR-genotyped OC-users and naturally cycling (NC) women in a carefully masked design. A homogenous sample of healthy, PMS-free, pre-menopausal MR-genotyped women (n=92) completed online questionnaires eight times during two consecutive cycles. The masking of the research question was successful. OC-users did not differ significantly from NC women in positive and negative affect at the time of assessment, personality characteristics (e.g. neuroticism) or mental and physical health. Both groups reported more shifts in anger in the first cycle week (p<0.001; η p 2 =0.08). Compared to NC women, OC-users reported fewer mood-shifts between depression and elation in the mid-luteal phase of the menstrual cycle (p=0.002; η p 2 =0.10) and had fewer ruminating thoughts at all phases (p=0.003; η p 2 =0.11). Effects of MR-genotype were not significant after correction for multiple comparisons. OC users scored more favorably on measures associated with reproductive depression. OC users also showed a decreased affect variability possibly indicating an emotional blunting effect, which is in line with previous reports on affect-stabilizing effects of OC. Limitations were loss of cases due to irregularities in the menstrual cycle length and possible confounding by the 'survivor effect', since almost all OC-users took OC for more than a year. Copyright © 2017 Elsevier Inc. All rights reserved.

Assessment of Musculoskeletal Strength and Levels of Fatigue during Different Phases of Menstrual Cycle in Young Adults

PubMed Central

D Souza, Urban John; Shivaprakash, G

2017-01-01

Introduction Some of the physiological factors and athletic performance might show variation along the phases of menstrual cycle. The alterations seen in these physiological parameters of various systems relating to oscillations in hormonal levels do affect the autonomic nervous system and metabolic functions. Former studies heave inconclusively about the influence of hormones on exercise performance, predominantly muscle strength and rate of fatigue during different phases of the menstrual cycle. Studies regarding influence of these variations during bleeding phase were not done. Aim To evaluate the muscle strength variations and also the rate of fatigue during various phases of the menstrual cycle in young adults. Materials and Methods This was a prospective study conducted among 100 healthy adult female volunteers aged 18-24 years, with normal regular menstrual cycles persistent between 26- 32 days (average of 28 days), for a minimum of last 6 months. Muscle strength was assessed by calculating the work done and fatigue rate using Mosso’s ergograph and by handgrip dynamometer strength. Each subject was evaluated consecutively for two menstrual cycles in all three phases which were classified as Phase 1- Menstrual phase, Phase 2- Follicular phase and Phase 3- Luteal phase. The data obtained was analysed by statistical tool One-way ANOVA followed by a post-hoc Tukeys test. A p-value of ≤ 0.05 was considered significant. Results The amount of work done and handgrip strength was significantly higher in phase 2 (p<0.001) and relatively reduced in phase 1 and 3 (p<0.001) of menstrual cycle. In terms of fatigue rate percentage, phase 2 showed significantly lesser values (p<0.001) as compared to phase 1 and 3 of menstrual cycle. Conclusion We conclude that the cyclical variation in endogenous reproductive hormones increases the muscle strength in follicular phase of the menstrual cycle. Thus provide support for the influence of these hormones in regulation of these parameters in the premenopausal age group. PMID:28384857

Advanced tracking systems design and analysis

NASA Technical Reports Server (NTRS)

Potash, R.; Floyd, L.; Jacobsen, A.; Cunningham, K.; Kapoor, A.; Kwadrat, C.; Radel, J.; Mccarthy, J.

1989-01-01

The results of an assessment of several types of high-accuracy tracking systems proposed to track the spacecraft in the National Aeronautics and Space Administration (NASA) Advanced Tracking and Data Relay Satellite System (ATDRSS) are summarized. Tracking systems based on the use of interferometry and ranging are investigated. For each system, the top-level system design and operations concept are provided. A comparative system assessment is presented in terms of orbit determination performance, ATDRSS impacts, life-cycle cost, and technological risk.

Environmental Assessment for Routine and Recurring Unmanned Aerial Vehicle Flight Operations at Edwards Air Force Base, California

DTIC Science & Technology

2006-11-01

grounds, spawning 28 sites, feeding sites, seasonal wetlands or drylands, water quality or quantity, host species or plant 29 pollinators , geological...cycles, and biotic interactions . As a 28 practical matter the guidance suggests that [environmental] assessments should focus on ecological 29...potential impacts were compared to the ten ecological 17 processes identified by the U.S. EPA and were found to be less than significant because of the

Prognostic indicators of assisted reproduction technology outcomes of cycles with ultralow serum antimüllerian hormone: a multivariate analysis of over 5,000 autologous cycles from the Society for Assisted Reproductive Technology Clinic Outcome Reporting System database for 2012-2013.

PubMed

Seifer, David B; Tal, Oded; Wantman, Ethan; Edul, Preeti; Baker, Valerie L

2016-02-01

To assess cycle outcomes when antimüllerian hormone (AMH) is ultralow (≤0.16 ng/mL) and to determine which parameters contribute to the probability of cycle cancellation and/or outcome. Retrospective analysis. Not applicable. 5,087 (7.3%) fresh and 243 (1.5%) thawed cycles with ultralow AMH values. Linear and logistic regression, comparison with age-matched cycles with normal AMH concentrations. Cancellation rate; number of retrieved oocytes, embryos, transferred embryos, and cryopreserved embryos; clinical pregnancy, live-birth, and multiple birth rates. The total cancellation rate per cycle start for fresh cycles was 54%. Of these, 38.6% of the cycles were canceled before retrieval, and 3.3% of cycles obtained no oocytes at time of retrieval. Of all retrieval attempts, 50.7% had three oocytes or fewer retrieved, and 25.1% had no embryo transfer. The live-birth rates were 9.5% per cycle start. Cycles with ultralow AMH levels compared with age-matched normal AMH cycles demonstrated more than a fivefold greater pre-retrieval cancellation rate, a twofold less live-birth rate per cycle and a 4.5-fold less embryo cryopreservation rate. Refusing treatment solely on the basis of ultralow AMH levels is not advisable, but patients should be counseled appropriately about the prognostic factors for cancellation and outcomes. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Ethanol or bioelectricity? Life cycle assessment of lignocellulosic bioenergy use in light-duty vehicles.

PubMed

Luk, Jason M; Pourbafrani, Mohammad; Saville, Bradley A; MacLean, Heather L

2013-09-17

Our study evaluates life cycle energy use and GHG emissions of lignocellulosic ethanol and bioelectricity use in U.S. light-duty vehicles. The well-to-pump, pump-to-wheel, and vehicle cycle stages are modeled. All ethanol (E85) and bioelectricity pathways have similar life cycle fossil energy use (~ 100 MJ/100 vehicle kilometers traveled (VKT)) and net GHG emissions (~5 kg CO2eq./100 VKT), considerably lower (65-85%) than those of reference gasoline and U.S. grid-electricity pathways. E85 use in a hybrid vehicle and bioelectricity use in a fully electric vehicle also have similar life cycle biomass and total energy use (~ 350 and ~450 MJ/100 VKT, respectively); differences in well-to-pump and pump-to-wheel efficiencies can largely offset each other. Our energy use and net GHG emissions results contrast with findings in literature, which report better performance on these metrics for bioelectricity compared to ethanol. The primary source of differences in the studies is related to our development of pathways with comparable vehicle characteristics. Ethanol or vehicle electrification can reduce petroleum use, while bioelectricity may displace nonpetroleum energy sources. Regional characteristics may create conditions under which either ethanol or bioelectricity may be the superior option; however, neither has a clear advantage in terms of GHG emissions or energy use.

Bithermal Low-Cycle Fatigue Evaluation of Automotive Exhaust System Alloy SS409

NASA Technical Reports Server (NTRS)

Lu, Gui-Ying; Behling, Mike B.; Halford, Gary R.

2000-01-01

This investigation provides, for the first time, cyclic strainrange-controlled, thermomechanical fatigue results for the ferritic stainless steel alloy SS409. The alloy has seen extensive application for automotive exhaust system components. The data were generated to calibrate the Total Strain Version of the Strainrange Partitioning (TS-SRP) method for eventual application to the design and durability assessment of automotive exhaust systems. The thermomechanical cyclic lifetime and cyclic stress-strain constitutive behavior for alloy SS409 were measured using bithermal tests cycling between isothermal extremes of 400 and 800 C. Lives ranged up to 10,000 cycles to failure with hold-times of 0.33 to 2.0 minutes. The bithermal fatigue behavior is compared to isothermal, strain-controlled fatigue behavior at both 400 and 800 C. Thermomechanical cycling was found to have a profound detrimental influence on the fatigue failure resistance of SS409 compared to isothermal cycling. Supplementary bithermal cyclic stress-strain constitutive tests with hold-times ranging from 40 seconds up to 1.5 hours were conducted to calibrate the TS-SRP equation for extrapolation to longer lifetime predictions. Observed thermomechanical (bithermal) fatigue lives correlated well with lives calculated using the calibrated TS-SRP equations: 70% of the bithermal fatigue data fall within a factor of 1.2 of calculated life; 85% within a factor of 1.4; and 100% within a factor of 1.8.

Advanced vehicle systems assessment. Volume 3: Systems assessment

NASA Technical Reports Server (NTRS)

Hardy, K.

1985-01-01

The systems analyses integrate the advanced component and vehicle characteristics into conceptual vehicles with identical performance (for a given application) and evaluates the vehicles in typical use patterns. Initial and life-cycle costs are estimated and compared to conventional reference vehicles with comparable technological advances, assuming the vehicles will be in competition in the early 1990s. Electric vans, commuter vehicles, and full-size vehicles, in addition to electric/heat-engine hybrid and fuel-cell powered vehicles, are addressed in terms of performance and economics. System and subsystem recommendations for vans and two-passenger commuter vehicles are based on the economic analyses in this volume.

Evaluating the Environmental Impacts of a Nano-Enhanced Field Emission Display Using Life Cycle Assessment: A Screening-Level Study

EPA Science Inventory

Carbon nanotube (CNT) field emission displays (FEDs) are currently in the product development stage and are expected to be commercialized in the near future because they offer image quality and viewing angles comparable to a cathode ray tube (CRT) while using a thinner structure,...

Economic and Environmental Assessment of Natural Gas Plants with Carbon Capture and Storage (NGCC-CCS)

EPA Science Inventory

The CO2 intensity of electricity produced by state-of-the-art natural gas combined-cycle turbines (NGCC) isapproximately one-third that of the U.S. fleet of existing coal plants. Compared to new nuclear plants and coal plantswith integrated carbon capture, NGCC has a lower invest...

A modular Human Exposure Model (HEM) framework to characterize near-field chemical exposure in LCIA and CAA

EPA Science Inventory

Life Cycle Impact Analysis (LCIA) has proven to be a valuable tool for systematically comparing processes and products, and has been proposed for use in Chemical Alternatives Analysis (CAA). The exposure assessment portion of the human health impact scores of LCIA has historicall...

A sutureless aortic stent-graft based on a nitinol scaffold bonded to a compliant nanocomposite polymer is durable for 10 years in a simulated in vitro model.

PubMed

Desai, Mital; Bakhshi, Raheleh; Zhou, Xiang; Odlyha, Marianne; You, Zhong; Seifalian, Alexander M; Hamilton, George

2012-06-01

To physiologically test the durability of a sutureless aortic stent-graft based on nitinol bonded to polyhedral oligomeric silsesquioxane (POSS) and poly(carbonate-urea) urethane (PCU) for 10 years according to Food and Drug Administration guidelines. Aortic stent-grafts (n = 4) were tested in 37°C distilled water using simulated in vivo hydrodynamic pulse loading. After 400 million cycles, surface topography was assessed by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. Dynamic compliance was measured using a pulsatile flow phantom. Mechanical and elastic properties were determined by stress-strain studies and elastic deformation tests. Dynamic scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to assess thermal resistance. Comparison was made with a zero-cycled control. All stent-grafts successfully completed accelerated pulsatile fatigue at 94±14-mmHg pulse pressure. SEM images confirmed uniform surface topography without any fractures. FTIR showed increased intensity of -NHCO- bonds, but there was no significant sign of biodegradation. Tensile stress of fatigue-tested polymer compared favorably with the zero-cycled control at 50% to 500% strain (p = 0.69). At a mean pressure range of 60 to 120 mmHg, overall compliance of the fatigue-tested grafts was 3.48±1.27%mmHg(-1)×10(-2) with no significant difference compared to control (3.26±0.65%mmHg(-1)×10(-2); p = 0.47). DSC and TMA showed comparable thermotropic transition. Simulated physiological in vivo hydrodynamic loading has no significant degradative effect on an innovative sutureless stent-graft made from POSS-PCU nanocomposite polymer. Sutureless technology incorporating nitinol stents proved to be robust, with no separation over an accelerated 10-year cycle, which may allow development of durable stent-grafts with better compliance.

Life cycle study of different constructive solutions for building enclosures.

PubMed

Garcia-Ceballos, Luz; de Andres-Díaz, Jose Ramon; Contreras-Lopez, Miguel A

2018-06-01

The construction sector must advance in a more sustainable way and to achieve this goal, the application of global methodologies is needed. These methodologies should take into account all life stages of a building: planning, design, construction, use and demolition. The quantity and variety of the materials used in building construction condition the buildings' environmental and energy impacts. Life Cycle Assessment offers a standardized framework to evaluate the environmental loads of a product, process or activity. This work aims to demonstrate the feasibility of using Life Cycle Assessment (LCA) to select facilities in the construction sector, which minimize environmental and energy impacts. To facilitate the understanding of the proposed methodology, a comparative LCA is performed, to determine the type of thermal insulating material in a double sheet ceramic façade and its thickness, which allows reducing the environmental impacts associated to the enclosure. The three most used enclosure types used in the city of Malaga (Spain) have been selected for this study. The results show the adequacy of the procedure used. Copyright © 2018 Elsevier B.V. All rights reserved.

Suppression of ovarian activity with a low-dose 21/7-day regimen oral contraceptive containing ethinylestradiol 20 mcg/drospirenone 3 mg in Japanese and Caucasian women.

PubMed

Anzai, Yuzuru; Heger-Mahn, Doris; Schellschmidt, Ilka; Marr, Joachim

2012-07-01

Two studies assessed the effect of a low-estrogen-dose 21/7-day oral contraceptive containing ethinylestradiol and drospirenone (EE 20 mcg/drsp 3 mg) on ovarian activity in Japanese and Caucasian women. Study 1 was conducted in Japanese women (20-35 years), and Study 2 was conducted in Caucasian women (18-35 years). All women received EE 20 mcg/drsp 3 mg in a 21-day active pill regimen. The primary endpoint was the proportion of women with ovulation inhibition (Hoogland score <6; as assessed by transvaginal ultrasonography) during treatment cycle 2. Japanese (n=23) and Caucasian (n=30) women received two cycles of study treatment. During treatment cycle 2, ovulation was inhibited in 100% and 92.9% of Japanese and Caucasian women, respectively. EE 20 mcg/drsp 3 mg in a 21/7-day regimen provides comparable ovarian suppression in Japanese and Caucasian women, with normal ovarian function resuming shortly after treatment end in both populations. Copyright © 2012 Elsevier Inc. All rights reserved.

Matrix approaches to assess terrestrial nitrogen scheme in CLM4.5

NASA Astrophysics Data System (ADS)

Du, Z.

2017-12-01

Terrestrial carbon (C) and nitrogen (N) cycles have been commonly represented by a series of balance equations to track their influxes into and effluxes out of individual pools in earth system models (ESMs). This representation matches our understanding of C and N cycle processes well but makes it difficult to track model behaviors. To overcome these challenges, we developed a matrix approach, which reorganizes the series of terrestrial C and N balance equations in the CLM4.5 into two matrix equations based on original representation of C and N cycle processes and mechanisms. The matrix approach would consequently help improve the comparability of models and data, evaluate impacts of additional model components, facilitate benchmark analyses, model intercomparisons, and data-model fusion, and improve model predictive power.

Quantifying the environmental impact of a Li-rich high-capacity cathode material in electric vehicles via life cycle assessment.

PubMed

Wang, Yuqi; Yu, Yajuan; Huang, Kai; Chen, Bo; Deng, Wensheng; Yao, Ying

2017-01-01

A promising Li-rich high-capacity cathode material (xLi 2 MnO 3 ·(1-x)LiMn 0.5 Ni 0.5 O 2 ) has received much attention with regard to improving the performance of lithium-ion batteries in electric vehicles. This study presents an environmental impact evaluation of a lithium-ion battery with Li-rich materials used in an electric vehicle throughout the life cycle of the battery. A comparison between this cathode material and a Li-ion cathode material containing cobalt was compiled in this study. The battery use stage was found to play a large role in the total environmental impact and high greenhouse gas emissions. During battery production, cathode material manufacturing has the highest environmental impact due to its complex processing and variety of raw materials. Compared to the cathode with cobalt, the Li-rich material generates fewer impacts in terms of human health and ecosystem quality. Through the life cycle assessment (LCA) results and sensitivity analysis, we found that the electricity mix and energy efficiency significantly influence the environmental impacts of both battery production and battery use. This paper also provides a detailed life cycle inventory, including firsthand data on lithium-ion batteries with Li-rich cathode materials.

Estimating net changes in life-cycle emissions from adoption of emerging civil infrastructure technologies.

PubMed

Amponsah, Isaac; Harrison, Kenneth W; Rizos, Dimitris C; Ziehl, Paul H

2008-01-01

There is a net emissions change when adopting new materials for use in civil infrastructure design. To evaluate the total net emissions change, one must consider changes in manufacture and associated life-cycle emissions, as well as changes in the quantity of material required. In addition, in principle one should also consider any differences in costs of the two designs because cost savings can be applied to other economic activities with associated environmental impacts. In this paper, a method is presented that combines these considerations to permit an evaluation of the net change in emissions when considering the adoption of emerging technologies/materials for civil infrastructure. The method factors in data on differences between a standard and new material for civil infrastructure, material requirements as specified in designs using both materials, and price information. The life-cycle assessment approach known as economic input-output life-cycle assessment (EIO-LCA) is utilized. A brief background on EIO-LCA is provided because its use is central to the method. The methodology is demonstrated with analysis of a switch from carbon steel to high-performance steel in military bridge design. The results are compared with a simplistic analysis that accounts for the weight reduction afforded by use of the high-performance steel but assuming no differences in manufacture.

Fuel Cycle Analysis Framework Base Cases for the IAEA/INPRO GAINS Collaborative Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brent Dixon

Thirteen countries participated in the Collaborative Project GAINS “Global Architecture of Innovative Nuclear Energy Systems Based on Thermal and Fast Reactors Including a Closed Fuel Cycle”, which was the primary activity within the IAEA/INPRO Program Area B: “Global Vision on Sustainable Nuclear Energy” for the last three years. The overall objective of GAINS was to develop a standard framework for assessing future nuclear energy systems taking into account sustainable development, and to validate results through sample analyses. This paper details the eight scenarios that constitute the GAINS framework base cases for analysis of the transition to future innovative nuclear energymore » systems. The framework base cases provide a reference for users of the framework to start from in developing and assessing their own alternate systems. Each base case is described along with performance results against the GAINS sustainability evaluation metrics. The eight cases include four using a moderate growth projection and four using a high growth projection for global nuclear electricity generation through 2100. The cases are divided into two sets, addressing homogeneous and heterogeneous scenarios developed by GAINS to model global fuel cycle strategies. The heterogeneous world scenario considers three separate nuclear groups based on their fuel cycle strategies, with non-synergistic and synergistic cases. The framework base case analyses results show the impact of these different fuel cycle strategies while providing references for future users of the GAINS framework. A large number of scenario alterations are possible and can be used to assess different strategies, different technologies, and different assumptions about possible futures of nuclear power. Results can be compared to the framework base cases to assess where these alternate cases perform differently versus the sustainability indicators.« less

Bicycle Trains, Cycling, and Physical Activity: A Pilot Cluster RCT.

PubMed

Mendoza, Jason A; Haaland, Wren; Jacobs, Maya; Abbey-Lambertz, Mark; Miller, Josh; Salls, Deb; Todd, Winifred; Madding, Rachel; Ellis, Katherine; Kerr, Jacqueline

2017-10-01

Increasing children's cycling to school and physical activity are national health goals. The objective was to conduct an RCT of a bicycle train program to assess impact on students' school travel mode and moderate-to-vigorous physical activity (MVPA). Pilot cluster RCT with randomization at the school level and N=54 participants. Fourth-fifth graders from four public schools serving low-income families in Seattle, WA in 2014 with analyses in 2015-2016. All participants were provided and fitted with bicycles, safety equipment (helmets, locks, and lights), and a 2- to 3-hour bicycle safety course. The intervention was a bicycle train offered daily (i.e., students volunteered to cycle with study staff to and from school). Time 1 assessments occurred prior to randomization. Time 2 assessments occurred after 3-5 weeks of the intervention (i.e., during Weeks 4-6 of the intervention period). The primary outcome was the percentage of daily commutes to school by cycling measured by validated survey. MVPA, measured by accelerometry and GPS units and processed by machine learning algorithms, was a secondary outcome. For two separate adjusted repeated measures linear mixed effects models in which students (N=54) were nested within schools (N=4), intervention participants had: (1) an absolute increase in mean percentage of daily commutes by cycling of 44.9%, (95% CI=26.8, 63.0) and (2) an increase in mean MVPA of 21.6 minutes/day, (95% CI=8.7, 34.6) from Time 1 to Time 2 compared with controls. A pilot bicycle train intervention increased cycling to school and daily MVPA in the short term among diverse, inner-city elementary school students. The bicycle train intervention appears promising and warrants further experimental trials among large, diverse samples with longer follow-up. This study is registered at www.clinicaltrials.gov NCT02006186. Copyright © 2017 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Systematic Review of Life Cycle Greenhouse Gas Emissions from Geothermal Electricity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eberle, Annika; Heath, Garvin A.; Carpenter Petri, Alberta C.

The primary goal of this work was to assess the magnitude and variability of published life cycle greenhouse gas (GHG) emission estimates for three types of geothermal electricity generation technologies: enhanced geothermal systems (EGS) binary, hydrothermal (HT) flash, and HT binary. These technologies were chosen to align the results of this report with technologies modeled in National Renewable Energy Laboratory's (NREL's) Regional Energy Deployment Systems (ReEDs) model. Although we did gather and screen life cycle assessment (LCA) literature on hybrid systems, dry steam, and two geothermal heating technologies, we did not analyze published GHG emission estimates for these technologies. Inmore » our systematic literature review of the LCA literature, we screened studies in two stages based on a variety of criteria adapted from NREL's Life Cycle Assessment (LCA) Harmonization study (Heath and Mann 2012). Of the more than 180 geothermal studies identified, only 29 successfully passed both screening stages and only 26 of these included estimates of life cycle GHG emissions. We found that the median estimate of life cycle GHG emissions (in grams of carbon dioxide equivalent per kilowatt-hour generated [g CO2eq/kWh]) reported by these studies are 32.0, 47.0, and 11.3 for EGS binary, HT flash, and HT binary, respectively (Figure ES-1). We also found that the total life cycle GHG emissions are dominated by different stages of the life cycle for different technologies. For example, the GHG emissions from HT flash plants are dominated by the operations phase owing to the flash cycle being open loop whereby carbon dioxide entrained in the geothermal fluids is released to the atmosphere. This is in contrast to binary plants (using either EGS or HT resources), whose GHG emissions predominantly originate in the construction phase, owing to its closed-loop process design. Finally, by comparing this review's literature-derived range of HT flash GHG emissions to data from currently operating geothermal plants, we found that emissions from operational plants exhibit more variability and the median of emissions from operational plants is twice the median of operational emissions reported by LCAs. Further investigation is warranted to better understand the cause of differences between published LCAs and estimates from operational plants and to develop LCA analytical approaches that can yield estimates closer to actual emissions.« less

Direct and indirect generation of waste in the Spanish paper industry.

PubMed

Ruiz Peñalver, Soraya María; Rodríguez Molina, Mercedes; Camacho Ballesta, José Antonio

2014-01-01

The paper industry has a relatively high degree of reliance on suppliers when compared to other industries. Exploring the role of the paper industry in terms of consumption of intermediate inputs from other industries may help to understand how the production of paper does not only generate waste by itself but also affects the amount of waste generated by other industries. The product Life Cycle Assessment (LCA) is a useful analytical tool to examine and assess environmental impacts over the entire life cycle of a product "from cradle to grave" but it is costly and time intensive. In contrast, Economic Input Output Life Cycle Assessment Models (IO-LCA) that combine LCA with Input-Output analysis (IO) are more accurate and less expensive, as they employ publicly available data. This paper represents one of the first Spanish studies aimed at estimating the waste generated in the production of paper by applying IO-LCA. One of the major benefits is the derivation of the contribution of direct and indirect suppliers to the paper industry. The results obtained show that there was no direct relationship between the impact on output and the impact on waste generation exerted by the paper industry. The major contributors to waste generation were the mining industry and the forestry industry. Copyright © 2013 Elsevier Ltd. All rights reserved.

Assessment and comparison of three high-aluminum fly ash utilization scenarios in Inner Mongolia, China using an eco-efficiency indicator.

PubMed

Yang, Shuo; Lin, Ling; Li, Shao Peng; Li, Qiang; Wang, Xiu Teng; Sun, Liang

2017-05-01

Utilization of fly ash is of great importance in China in the context of resource and environmental crises. Different fly ash utilization processes are proposed, and some have been practically applied. However, none of these fly ash utilization pathways has been evaluated comprehensively by integrating both environmental and economic perspectives. In this study, three high-aluminum fly ash utilization methods in Mongolia were assessed and compared based on the concept of eco-efficiency. The environmental assessment was conducted in accordance with life-cycle assessment principles, and a monetization-weighting approach was applied to obtain social willingness-to-pay as a reflection of environmental impact. The environmental assessment results revealed that the reuse of fly ash had significant advantage for saving primary resource, while solid waste, depletion of water, and global warming were the three highest environmental impacts from the life cycle perspective. The economic performance assessment showed positive net profits for fly ash utilization, but high value-added products were not necessarily indicative of better economic performance due to the relatively high operation cost. Comparison of the eco-efficiency indicators (EEIs) implied that the process of scenario 1#, which produced mullite ceramic and active calcium silicate, was the most recommended out of the three scenarios on the present scale. This judgment was consistent with the evaluation of the resource utilization rate. The present study showed that the EEI could be used to compare different fly ash utilization processes in a comprehensive and objective manner, thus providing definitive and insightful suggestions for decision-making and technical improvement.

Ovarian acyclicity in zoo African elephants (Loxodonta africana) is associated with high body condition scores and elevated serum insulin and leptin.

PubMed

Morfeld, Kari A; Brown, Janine L

2016-04-01

The purpose of the present study was to determine whether excessive body fat and altered metabolic hormone concentrations in the circulation were associated with ovarian acyclicity in the world's largest land mammal, the African elephant. We compared body condition, glucose, insulin and leptin concentrations and the glucose-to-insulin ratio (G:I) between cycling (n=23; normal 14-16 week cycles based on serum progestagens for at least 2 years) and non-cycling (n=23; consistent baseline progestagen concentrations for at least 2 years) females. A validated body condition score (BCS) index (five-point scale; 1=thinnest, 5=fattest) was used to assess the degree of fatness of the study elephants. The mean BCS of non-cycling elephants was higher than that of their cycling counterparts. There were differences in concentrations of serum metabolic biomarkers, with non-cycling elephants in the BCS 5 category having higher leptin and insulin concentrations and a lower G:I ratio than cycling BCS 5 females. Using 'non-cycling' as the outcome variable in regression models, high BCS was a strong predictor of a non-cycling status. This study provides the first evidence that ovarian acyclicity in zoo African elephants is associated with body condition indicative of obesity, as well as elevated, perturbed biomarkers of metabolic status.

Prolonged menstrual cycles in female workers exposed to ethylene glycol ethers in the semiconductor manufacturing industry.

PubMed

Hsieh, G-Y; Wang, J-D; Cheng, T-J; Chen, P-C

2005-08-01

It has been shown that female workers exposed to ethylene glycol ethers (EGEs) in the semiconductor industry have higher risks of spontaneous abortion, subfertility, and menstrual disturbances, and prolonged waiting time to pregnancy. To examine whether EGEs or other chemicals are associated with long menstrual cycles in female workers in the semiconductor manufacturing industry. Cross-sectional questionnaire survey during the annual health examination at a wafer manufacturing company in Taiwan in 1997. A three tiered exposure-assessment strategy was used to analyse the risk. A short menstrual cycle was defined to be a cycle less than 24 days and a long cycle to be more than 35 days. There were 606 valid questionnaires from 473 workers in fabrication jobs and 133 in non-fabrication areas. Long menstrual cycles were associated with workers in fabrication areas compared to those in non-fabrication areas. Using workers in non-fabrication areas as referents, workers in photolithography and diffusion areas had higher risks for long menstrual cycles. Workers exposed to EGEs and isopropanol, and hydrofluoric acid, isopropanol, and phosphorous compounds also showed increased risks of a long menstrual cycle. Exposure to multiple chemicals, including EGEs in photolithography, might be associated with long menstrual cycles, and may play an important role in a prolonged time to pregnancy in the wafer manufacturing industry; however, the prevalence in the design, possible exposure misclassification, and chance should be considered.

Effects of visceral adiposity on glycerol pathways in gluconeogenesis.

PubMed

Neeland, Ian J; Hughes, Connor; Ayers, Colby R; Malloy, Craig R; Jin, Eunsook S

2017-02-01

To determine the feasibility of using oral 13 C labeled glycerol to assess effects of visceral adiposity on gluconeogenic pathways in obese humans. Obese (BMI ≥30kg/m 2 ) participants without type 2 diabetes underwent visceral adipose tissue (VAT) assessment and stratification by median VAT into high VAT-fasting (n=3), low VAT-fasting (n=4), and high VAT-refed (n=2) groups. Participants ingested [U- 13 C 3 ] glycerol and blood samples were subsequently analyzed at multiple time points over 3h by NMR spectroscopy. The fractions of plasma glucose (enrichment) derived from [U- 13 C 3 ] glycerol via hepatic gluconeogenesis, pentose phosphate pathway (PPP), and tricarboxylic acid (TCA) cycle were assessed using 13 C NMR analysis of glucose. Mixed linear models were used to compare 13 C enrichment in glucose between groups. Mean age, BMI, and baseline glucose were 49years, 40.1kg/m 2 , and 98mg/dl, respectively. Up to 20% of glycerol was metabolized in the TCA cycle prior to gluconeogenesis and PPP activity was minor (<1% of total glucose) in all participants. There was a 21% decrease in 13 C enrichment in plasma glucose in the high VAT-fasting compared with low VAT-fasting group (p=0.03), suggesting dilution by endogenous glycerol. High VAT-refed participants had 37% less 13 C enrichment in glucose compared with high VAT-fasting (p=0.02). There was a trend toward lower [1,2- 13 C 2 ] (via PPP) and [5,6- 13 C 2 ]/[4,5,6- 13 C 3 ] (via TCA cycle) glucose in high VAT versus low VAT groups. We applied a simple method to detect gluconeogenesis from glycerol in obese humans. Our findings provide preliminary evidence that excess visceral fat disrupts multiple pathways in hepatic gluconeogenesis from glycerol. Copyright © 2016 Elsevier Inc. All rights reserved.

Effects of Visceral Adiposity on Glycerol Pathways in Gluconeogenesis

PubMed Central

Neeland, Ian J.; Hughes, Connor; Ayers, Colby R.; Malloy, Craig R.; Jin, Eunsook S.

2016-01-01

Objective To determine the feasibility of using oral 13C labeled glycerol at assess effects of visceral adiposity on gluconeogenic pathways in obese humans. Research Design and Methods Obese (BMI ≥30 kg/m2) participants without type 2 diabetes underwent visceral adipose tissue (VAT) assessment and stratification by median VAT into high VAT-fasting (n=3), low VAT-fasting (n=4), and high VAT-refed (n=2) groups. Participants ingested [U-13C3] glycerol and blood samples were subsequently analyzed at multiple time points over 3 hours by NMR spectroscopy. The fractions of plasma glucose (enrichment) derived from [U-13C3] glycerol via hepatic gluconeogenesis, pentose phosphate pathway (PPP), and tricarboxylic acid (TCA) cycle were assessed using 13C NMR analysis of glucose. Mixed linear models were used to compare 13C enrichment in glucose between groups. Results Mean age, BMI, and baseline glucose were 49 years, 40.1 kg/m2, and 98 mg/dl, respectively. Up to 20% of glycerol was metabolized in the TCA cycle prior to gluconeogenesis and PPP activity was minor (<1% of total glucose) in all participants. There was a 21% decrease in 13C enrichment in plasma glucose in the high VAT-fasting compared with low VAT-fasting group (p=0.03), suggesting dilution by endogenous glycerol. High VAT-refed participants had 37% less 13C enrichment in glucose compared with high VAT-fasting (p=0.02). There was a trend toward lower [1,2-13C2] (via PPP) and [5,6-13C2]/[4,5,6-13C3] (via TCA cycle) glucose in high VAT versus low VAT groups. Conclusions We applied a simple method to detect gluconeogenesis from glycerol in obese humans. Our findings provide preliminary evidence that excess visceral fat disrupts multiple pathways in hepatic gluconeogenesis from glycerol. PMID:28081781

Health impact assessment of cycling network expansions in European cities.

PubMed

Mueller, Natalie; Rojas-Rueda, David; Salmon, Maëlle; Martinez, David; Ambros, Albert; Brand, Christian; de Nazelle, Audrey; Dons, Evi; Gaupp-Berghausen, Mailin; Gerike, Regine; Götschi, Thomas; Iacorossi, Francesco; Int Panis, Luc; Kahlmeier, Sonja; Raser, Elisabeth; Nieuwenhuijsen, Mark

2018-04-01

We conducted a health impact assessment (HIA) of cycling network expansions in seven European cities. We modeled the association between cycling network length and cycling mode share and estimated health impacts of the expansion of cycling networks. First, we performed a non-linear least square regression to assess the relationship between cycling network length and cycling mode share for 167 European cities. Second, we conducted a quantitative HIA for the seven cities of different scenarios (S) assessing how an expansion of the cycling network [i.e. 10% (S1); 50% (S2); 100% (S3), and all-streets (S4)] would lead to an increase in cycling mode share and estimated mortality impacts thereof. We quantified mortality impacts for changes in physical activity, air pollution and traffic incidents. Third, we conducted a cost-benefit analysis. The cycling network length was associated with a cycling mode share of up to 24.7% in European cities. The all-streets scenario (S4) produced greatest benefits through increases in cycling for London with 1,210 premature deaths (95% CI: 447-1,972) avoidable annually, followed by Rome (433; 95% CI: 170-695), Barcelona (248; 95% CI: 86-410), Vienna (146; 95% CI: 40-252), Zurich (58; 95% CI: 16-100) and Antwerp (7; 95% CI: 3-11). The largest cost-benefit ratios were found for the 10% increase in cycling networks (S1). If all 167 European cities achieved a cycling mode share of 24.7% over 10,000 premature deaths could be avoided annually. In European cities, expansions of cycling networks were associated with increases in cycling and estimated to provide health and economic benefits. Copyright © 2018 Elsevier Inc. All rights reserved.

The Impact of Preexisting Chronic Kidney Disease on the Severity and Recovery of Acute Kidney Injury.

PubMed

Lim, Sung Yoon; Ko, Yoon Sook; Lee, Hee Young; Yang, Ji Hyun; Kim, Myung Gyu; Jo, Sang Kyung; Cho, Won Yong

2018-04-12

Recent observational studies have shown that in chronic kidney disease (CKD) patients, a significantly smaller percentage of patients with an episode of acute kidney injury (AKI) have full recovery of renal function compared to those without CKD. However, precise mechanisms involved in the incomplete repair after AKI with preexisting CKD have not been completely ascertained. Here, we assessed the impact of preexisting CKD on the severity and recovery of AKI in a mouse model of 5/6 nephrectomy. Male CD-1 mice underwent 5/6 nephrectomy (Nx). Six weeks post surgery, ischemia reperfusion injury (IRI) or a sham operation was performed and functional, histological, and various molecular parameters were compared between them. Serum creatinine level on day 1 after IRI was comparable between control and Nx mice. However, serum creatinine remained significantly higher throughout the recovery phase in Nx mice compared to control mice. mRNA and protein expression of the cell cycle regulatory proteins were persistently elevated in Nx mice and this was associated with significantly increased levels of the G1 cell cycle arrest markers. Treatment with a p53 inhibitor following IRI resulted in not only decreased expression of G1 arrest markers but also decreased fibrosis, suggesting that prolonged epithelial G1 cell cycle arrest might be partially responsible for impaired recovery from superimposed AKI on CKD. Taken together, reduced nephron mass have a negative effect on the repair process that is partially mediated by the disruption of the cell cycle regulation. © 2018 S. Karger AG, Basel.

Life cycle assessment and economic analysis of a low concentrating photovoltaic system.

PubMed

De Feo, G; Forni, M; Petito, F; Renno, C

2016-10-01

Many new photovoltaic (PV) applications, such as the concentrating PV (CPV) systems, are appearing on the market. The main characteristic of CPV systems is to concentrate sunlight on a receiver by means of optical devices and to decrease the solar cells area required. A low CPV (LCPV) system allows optimizing the PV effect with high increase of generated electric power as well as decrease of active surface area. In this paper, an economic analysis and a life cycle assessment (LCA) study of a particular LCPV scheme is presented and its environmental impacts are compared with those of a PV traditional system. The LCA study was performed with the software tool SimaPro 8.0.2, using the Econinvent 3.1 database. A functional unit of 1 kWh of electricity produced was chosen. Carbon Footprint, Ecological Footprint and ReCiPe 2008 were the methods used to assess the environmental impacts of the LCPV plant compared with a corresponding traditional system. All the methods demonstrated the environmental convenience of the LCPV system. The innovative system allowed saving 16.9% of CO2 equivalent in comparison with the traditional PV plant. The environmental impacts saving was 17% in terms of Ecological Footprint, and, finally, 15.8% with the ReCiPe method.

Effect of bright light therapy on delayed sleep/wake cycle and reaction time of athletes participating in the Rio 2016 Olympic Games.

PubMed

Rosa, João Paulo P; Silva, Andressa; Rodrigues, Dayane F; Simim, Mário Antônio; Narciso, Fernanda V; Tufik, Sergio; Bichara, Jorge J; Pereira, Sebastian Rafael D; Da Silva, Sidney C; de Mello, Marco Tulio

2018-04-16

This study investigated the effect of using an artificial bright light on the entrainment of the sleep/wake cycle as well as the reaction times of athletes before the Rio 2016 Olympic Games. A total of 22 athletes from the Brazilian Olympic Swimming Team were evaluated, with the aim of preparing them to compete at a time when they would normally be about to go to bed for the night. During the 8-day acclimatization period, their sleep/wake cycles were assessed by actigraphy, with all the athletes being treated with artificial light therapy for between 30 and 45 min (starting at day 3). In addition, other recommendations to improve sleep hygiene were made to the athletes. In order to assess reaction times, the Psychomotor Vigilance Test was performed before (day 1) and after (day 8) the bright light therapy. As a result of the intervention, the athletes slept later on the third (p = 0.01), seventh (p = 0.01) and eighth (p = 0.01) days after starting bright light therapy. Regarding reaction times, when tested in the morning the athletes showed improved average (p = 0.01) and minimum reaction time (p = 0.03) when comparing day 8 to day 1. When tested in the evening, they showed improved average (p = 0.04), minimum (p = 0.03) and maximum reaction time (p = 0.02) when comparing day 8 to day 1. Light therapy treatment delayed the sleep/wake cycles and improved reaction times of members of the swimming team. The use of bright light therapy was shown to be effective in modulating the sleep/wake cycles of athletes who had to perform in competitions that took place late at night.

Assessing the Role of Dissolved Organic Phosphate on Rates of Microbial Phosphorus Cycling

NASA Astrophysics Data System (ADS)

Gonzalez, A. C.; Popendorf, K. J.; Duhamel, S.

2016-02-01

Phosphorus (P) is an element crucial to life, and it is limiting in many parts of the ocean. In oligotrophic environments, the dissolved P pool is cycled rapidly through the activity of microbes, with turnover times of several hours or less. The overarching aim of this study was to assess the flux of P from picoplankton to the dissolved pool and the role this plays in fueling rapid P cycling. To determine if specific microbial groups are responsible for significant return of P to the dissolved pool during cell lifetime, we compared the rate of cellular P turnover (cell-Pτ, the rate of cellular P uptake divided by cellular P content) to the rate of cellular biomass turnover (cellτ). High rates of P return to the dissolved pool during cell lifetime (high cell-Pτ/cellτ) indicate significant P regeneration, fueling more rapid turnover of the dissolved P pool. We hypothesized that cell-Pτ/cellτ varies widely across picoplankton groups. One factor influencing this variation may be each microbial group's relative uptake of dissolved organic phosphorus (DOP) versus dissolved inorganic phosphorus (DIP). As extracellular hydrolysis is necessary for P incorporation from DOP, this process may return more P to the dissolved pool than DIP incorporation. This leads to the question: does a picoplankton's relative uptake of DOP (versus DIP) affect the rate at which it returns phosphorus to the dissolved pool? To address this question, we compared the rate of cellular P turnover based on uptake of DOP and uptake DIP using cultured representatives of three environmentally significant picoplankton groups: Prochlorococcus, Synechococcus, and heterotrophic bacteria. These different picoplankton groups are known to take up different ratios of DOP to DIP, and may in turn make significantly different contributions to the regeneration and cycling phosphorus. These findings have implications towards our understanding of the timeframes of biogeochemical cycling of phosphorus in the ocean.

A case-control pilot study of low-intensity IVF in good-prognosis patients.

PubMed

Gleicher, Norbert; Weghofer, Andrea; Barad, David H

2012-04-01

Low-intensity IVF (LI-IVF) is rapidly gaining in popularity. Yet studies comparing LI-IVF to standard IVF are lacking. This is a case-control pilot study, reporting on 14 first LI-IVF and 14 standard IVF cycles in women with normal age-specific ovarian reserve under age 38, matched for age, laboratory environment, staff and time of cycle. LI-IVF cycles underwent mild ovarian stimulation, utilizing clomiphene citrate, augmented by low-dose gonadotrophin stimulation. Control patients underwent routine ovarian stimulation. LI-IVF and regular IVF patients were similar in age, body mass index, FSH and anti-Müllerian hormone. Standard IVF utilized more gonadotrophins (P<0.001), yielded more oocytes (P<0.001) and cryopreserved more embryos (P<0.001). With similar embryo numbers transferred, after ethnicity adjustments, standard IVF demonstrated better odds for pregnancy (OR 7.07; P=0.046) and higher cumulative pregnancy rates (63.3% versus 21.4%; OR 6.6; P=0.02). Adjustments for age, ethnicity and diagnosis maintained significance but oocyte adjustment did not. Cost assessments failed to reveal differences between LI-IVF and standard IVF. In this small study, LI-IVF reduced pregnancy chances without demonstrating cost advantages, raising questions about its utility. In the absence of established clinical and/or economic foundations, LI-IVF should be considered an experimental procedure. Low-intensity IVF (LI-IVF) is increasingly propagated as an alternative to standard IVF. LI-IVF has, however, never been properly assessed in comparison to standard IVF. Such a comparison is presented in the format of a small pilot study, matching LI-IVF cycles with regular IVF cycles and comparing outcomes as well as costs. The study suggests that LI-IVF, at least in this setting, is clinically inferior and economically at best similar to standard IVF. LI-IVF should, therefore, as of this point not be offered as routine IVF treatment but only as an experimental procedure. Copyright © 2012 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Cycle ergometer and inspiratory muscle training offer modest benefit compared with cycle ergometer alone: a comprehensive assessment in stable COPD patients

PubMed Central

Luo, Yu-wen; Wang, Mei; Hu, Yu-he; Xu, Wen-hui; Zhou, Lu-qian; Chen, Rong-chang; Chen, Xin

2017-01-01

Background Cycle ergometer training (CET) has been shown to improve exercise performance of the quadriceps muscles in patients with COPD, and inspiratory muscle training (IMT) may improve the pressure-generating capacity of the inspiratory muscles. However, the effects of combined CET and IMT remain unclear and there is a lack of comprehensive assessment. Materials and methods Eighty-one patients with COPD were randomly allocated to three groups: 28 received 8 weeks of CET + IMT (combined training group), 27 received 8 weeks of CET alone (CET group), and 26 only received 8 weeks of free walking (control group). Comprehensive assessment including respiratory muscle strength, exercise capacity, pulmonary function, dyspnea, quality of life, emotional status, nutritional status, and body mass index, airflow obstruction, and exercise capacity index were measured before and after the pulmonary rehabilitation program. Results Respiratory muscle strength, exercise capacity, inspiratory capacity, dyspnea, quality of life, depression and anxiety, and nutritional status were all improved in the combined training and CET groups when compared with that in the control group (P<0.05) after pulmonary rehabilitation program. Inspiratory muscle strength increased significantly in the combined training group when compared with that in the CET group (ΔPImax [maximal inspiratory pressure] 5.20±0.89 cmH2O vs 1.32±0.91 cmH2O; P<0.05). However, there were no significant differences in the other indices between the two groups (P>0.05). Patients with weakened respiratory muscles in the combined training group derived no greater benefit than those without respiratory muscle weakness (P>0.05). There were no significant differences in these indices between the patients with malnutrition and normal nutrition after pulmonary rehabilitation program (P>0.05). Conclusion Combined training is more effective than CET alone for increasing inspiratory muscle strength. IMT may not be useful when combined with CET in patients with weakened inspiratory muscles. Nutritional status had slight impact on the effects of pulmonary rehabilitation. A comprehensive assessment approach can be more objective to evaluate the effects of combined CET and IMT. PMID:28919733

Cycle ergometer and inspiratory muscle training offer modest benefit compared with cycle ergometer alone: a comprehensive assessment in stable COPD patients.

PubMed

Wang, Kai; Zeng, Guang-Qiao; Li, Rui; Luo, Yu-Wen; Wang, Mei; Hu, Yu-He; Xu, Wen-Hui; Zhou, Lu-Qian; Chen, Rong-Chang; Chen, Xin

2017-01-01

Cycle ergometer training (CET) has been shown to improve exercise performance of the quadriceps muscles in patients with COPD, and inspiratory muscle training (IMT) may improve the pressure-generating capacity of the inspiratory muscles. However, the effects of combined CET and IMT remain unclear and there is a lack of comprehensive assessment. Eighty-one patients with COPD were randomly allocated to three groups: 28 received 8 weeks of CET + IMT (combined training group), 27 received 8 weeks of CET alone (CET group), and 26 only received 8 weeks of free walking (control group). Comprehensive assessment including respiratory muscle strength, exercise capacity, pulmonary function, dyspnea, quality of life, emotional status, nutritional status, and body mass index, airflow obstruction, and exercise capacity index were measured before and after the pulmonary rehabilitation program. Respiratory muscle strength, exercise capacity, inspiratory capacity, dyspnea, quality of life, depression and anxiety, and nutritional status were all improved in the combined training and CET groups when compared with that in the control group ( P <0.05) after pulmonary rehabilitation program. Inspiratory muscle strength increased significantly in the combined training group when compared with that in the CET group (ΔPI max [maximal inspiratory pressure] 5.20±0.89 cmH 2 O vs 1.32±0.91 cmH 2 O; P <0.05). However, there were no significant differences in the other indices between the two groups ( P >0.05). Patients with weakened respiratory muscles in the combined training group derived no greater benefit than those without respiratory muscle weakness ( P >0.05). There were no significant differences in these indices between the patients with malnutrition and normal nutrition after pulmonary rehabilitation program ( P >0.05). Combined training is more effective than CET alone for increasing inspiratory muscle strength. IMT may not be useful when combined with CET in patients with weakened inspiratory muscles. Nutritional status had slight impact on the effects of pulmonary rehabilitation. A comprehensive assessment approach can be more objective to evaluate the effects of combined CET and IMT.

Life cycle analysis of pistachio production in Greece.

PubMed

Bartzas, Georgios; Komnitsas, Kostas

2017-10-01

In the present paper, a life cycle assessment (LCA) study regarding pistachio (Pistacia vera L.) cultivation in Aegina island, Greece, was performed to evaluate the energy use footprint and the associated environmental impacts. In this context, a detailed life cycle inventory was created based on site-survey data and used for a holistic cradle-to-farm gate LCA analysis using the GaBi 6.5 software. The main impact categories assessed were acidification potential (AP), eutrophication potential (EP), global warming potential (GWP), ozone depletion potential (ODP), photochemical ozone creation potential (POCP) and cumulative energy demand (CED). In order to reveal the main environmental concerns pertinent to pistachio production and in turn propose measures for the reduction of environmental and energetic impacts, three scenarios were compared, namely the Baseline scenario (BS) that involves current cultivation practices, the Green Energy (GE) scenario that involves the use of biological fertilizers i.e. compost, and the Waste Utilization (WU) scenario that involves the production of biochar from pistachio and other agricultural wastes and its subsequent soil application to promote carbon sequestration and improve soil quality. Based on the results of this study, the use of compost for fertilization (GE scenario), which results in approximately 9% savings in terms of energy consumption and the five environmental impact categories studied compared to BS scenario, is considered a promising alternative cultivation strategy. Slightly higher savings (10% on average) in terms of the five calculated environmental impact categories, compared to the BS scenario, were indicated when the WU scenario was considered. Regarding energy consumption, the WU scenario results in minor increase, 3%, compared to the BS scenario. Results of uncertainty analysis performed using the Monte Carlo technique and contribution analysis showed that GE and WU scenarios offer reliable and significant eco-profile improvements for pistachio production in the study area compared to the current situation. Copyright © 2017 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampert, David J.; Cai, Hao; Wang, Zhichao

The production of all forms of energy consumes water. To meet increased energy demands, it is essential to quantify the amount of water consumed in the production of different forms of energy. By analyzing the water consumed in different technologies, it is possible to identify areas for improvement in water conservation and reduce water stress in energy-producing regions. The transportation sector is a major consumer of energy in the United States. Because of the relationships between water and energy, the sustainability of transportation is tied to management of water resources. Assessment of water consumption throughout the life cycle of amore » fuel is necessary to understand its water resource implications. To perform a comparative life cycle assessment of transportation fuels, it is necessary first to develop an inventory of the water consumed in each process in each production supply chain. The Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model is an analytical tool that can used to estimate the full life-cycle environmental impacts of various transportation fuel pathways from wells to wheels. GREET is currently being expanded to include water consumption as a sustainability metric. The purpose of this report was to document data sources and methodologies to estimate water consumption factors (WCF) for the various transportation fuel pathways in GREET. WCFs reflect the quantity of freshwater directly consumed per unit production for various production processes in GREET. These factors do not include consumption of precipitation or low-quality water (e.g., seawater) and reflect only water that is consumed (i.e., not returned to the source from which it was withdrawn). The data in the report can be combined with GREET to compare the life cycle water consumption for different transportation fuels.« less

Conceptual Framework To Extend Life Cycle Assessment Using Near-Field Human Exposure Modeling and High-Throughput Tools for Chemicals

EPA Science Inventory

Life Cycle Assessment (LCA) is a decision-making tool that accounts for multiple impacts across the life cycle of a product or service. This paper presents a conceptual framework to integrate human health impact assessment with risk screening approaches to extend LCA to include n...

Nitrogen Cycle Evaluation (NiCE) Chip for the Simultaneous Analysis of Multiple N-Cycle Associated Genes.

PubMed

Oshiki, Mamoru; Segawa, Takahiro; Ishii, Satoshi

2018-02-02

Various microorganisms play key roles in the Nitrogen (N) cycle. Quantitative PCR (qPCR) and PCR-amplicon sequencing of the N cycle functional genes allow us to analyze the abundance and diversity of microbes responsible in the N transforming reactions in various environmental samples. However, analysis of multiple target genes can be cumbersome and expensive. PCR-independent analysis, such as metagenomics and metatranscriptomics, is useful but expensive especially when we analyze multiple samples and try to detect N cycle functional genes present at relatively low abundance. Here, we present the application of microfluidic qPCR chip technology to simultaneously quantify and prepare amplicon sequence libraries for multiple N cycle functional genes as well as taxon-specific 16S rRNA gene markers for many samples. This approach, named as N cycle evaluation (NiCE) chip, was evaluated by using DNA from pure and artificially mixed bacterial cultures and by comparing the results with those obtained by conventional qPCR and amplicon sequencing methods. Quantitative results obtained by the NiCE chip were comparable to those obtained by conventional qPCR. In addition, the NiCE chip was successfully applied to examine abundance and diversity of N cycle functional genes in wastewater samples. Although non-specific amplification was detected on the NiCE chip, this could be overcome by optimizing the primer sequences in the future. As the NiCE chip can provide high-throughput format to quantify and prepare sequence libraries for multiple N cycle functional genes, this tool should advance our ability to explore N cycling in various samples. Importance. We report a novel approach, namely Nitrogen Cycle Evaluation (NiCE) chip by using microfluidic qPCR chip technology. By sequencing the amplicons recovered from the NiCE chip, we can assess diversities of the N cycle functional genes. The NiCE chip technology is applicable to analyze the temporal dynamics of the N cycle gene transcriptions in wastewater treatment bioreactors. The NiCE chip can provide high-throughput format to quantify and prepare sequence libraries for multiple N cycle functional genes. While there is a room for future improvement, this tool should significantly advance our ability to explore the N cycle in various environmental samples. Copyright © 2018 American Society for Microbiology.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The purpose of this analysis is to provide information necessary for the Department of Energy (DOE) to evaluate the practical utility of the Nitrate to Ammonia and Ceramic or Glass (NAC/NAG/NAX) process, which is under development in the Oak Ridge National Laboratory. The NAC/NACx/NAX process can convert aqueous radioactive nitrate-laden waste to a glass, ceramic, or grout solid waste form. The tasks include, but are not limited to, the following: Identify current commercial technologies to meet hazardous and radiological waste disposal requirements. The technologies may be thermal or non-thermal but must be all inclusive (i.e., must convert a radionuclide-containing nitratemore » waste with a pH around 12 to a stable form that can be disposed at permitted facilities); evaluate and compare DOE-sponsored vitrification, grouting, and minimum additive waste stabilization projects for life-cycle costs; compare the technologies above with respect to material costs, capital equipment costs, operating costs, and operating efficiencies. For the NAC/NAG/NAX process, assume aluminum reactant is government furnished and ammonia gas may be marketed; compare the identified technologies with respect to frequency of use within DOE for environmental management applications with appropriate rationale for use; Assess the potential size of the DOE market for the NAC/NAG/NAX process; assess and off-gas issues; and compare with international technologies, including life-cycle estimates.« less

Capecitabine in addition to anthracycline- and taxane-based neoadjuvant treatment in patients with primary breast cancer: phase III GeparQuattro study.

PubMed

von Minckwitz, Gunter; Rezai, Mahdi; Loibl, Sibylle; Fasching, Peter A; Huober, Jens; Tesch, Hans; Bauerfeind, Ingo; Hilfrich, Jörn; Eidtmann, Holger; Gerber, Bernd; Hanusch, Claus; Kühn, Thorsten; du Bois, Andreas; Blohmer, Jens-Uwe; Thomssen, Christoph; Dan Costa, Serban; Jackisch, Christian; Kaufmann, Manfred; Mehta, Keyur; Untch, Michael

2010-04-20

PURPOSE Capecitabine can be integrated either concomitantly or sequentially to anthracycline-plus-taxane-based regimens. PATIENTS AND METHODS Patients with large operable or locally advanced tumors, with hormone receptor-negative tumors, or with receptor-positive tumors but also clinically node-positive disease were recruited to receive preoperatively four cycles of epirubicin plus cyclophosphamide (EC; epirubicin 90 mg/m(2) and cyclophosphamide 600 mg/m(2)). Patients were then randomly assigned to four cycles of docetaxel (100 mg/m(2)), four cycles of docetaxel + capecitabine (TX; docetaxel 75 mg/m(2) plus capecitabine 1,800 mg/m(2)), or four cycles of docetaxel (75 mg/m(2)) followed by four cycles of capecitabine (1,800 mg/m(2); T-X). Patients with human epidermal growth factor receptor 2 (HER-2) -positive tumors received trastuzumab concomitantly with all cycles. Primary objectives were to assess the effect of docetaxel by comparing EC plus docetaxel versus EC plus TX and to assess the effect of duration by comparing EC plus TX versus EC plus T-X on pathologic complete response (pCR, without invasive/noninvasive breast tumor, regardless of nodal status) at surgery, irrespective of trastuzumab treatment. Results Of 1,509 patients starting EC, 1,421 were randomly assigned to docetaxel (n = 471), TX (n = 471), or T-X (n = 479). At surgery, pCR rates were 22.3%, 19.5%, and 22.3%, respectively; the difference for docetaxel (EC plus docetaxel v EC plus TX) was 2.8% (95% CI, -2.4% to 8.0%; P = .298).The difference for duration was -2.8% (95% CI, -8.0% to 2.4%; P = .298). Breast conservation rates were 70.1%, 68.4%, and 65.3%, respectively (P = .781 for docetaxel; P = .270 for duration). Concomitant but not sequential treatment with docetaxel was associated with more diarrhea; nail changes, and hand-foot-syndrome, but it was associated with less edema. CONCLUSION Adding capecitabine to or prolonging duration of neoadjuvant EC plus docetaxel does not result in higher efficacy at surgery.

Decreased pregnancy and live birth rates after vitrification of in vitro matured oocytes.

PubMed

Cohen, Yoni; St-Onge-St-Hilaire, Alexandra; Tannus, Samer; Younes, Grace; Dahan, Michael H; Buckett, William; Son, Weon-Young

2018-06-04

To assess effects on fertilization rate, embryo quality, pregnancy, and live birth rates of vitrification and warming of oocytes that matured in vitro (vIVM) compared to fresh in vitro maturation (fIVM) cycles. A retrospective cohort study conducted at a university hospital-affiliated IVF unit. Fifty-six cycles of vIVM cycles and 263 fIVM in women diagnosed with polycystic ovarian syndrome (PCOS) ovaries were included in the analysis. The study group included PCOS patients who failed ovulation induction with intrauterine insemination and were offered IVM cycle followed by oocyte vitrification and warming. The embryological aspects and clinical outcomes were compared to those of controls undergoing fresh IVM cycles during the same period. The main outcome measure was live birth rate. One thousand seventy oocytes were collected from 56 patients and underwent vitrification and warming. In the control group, 4781 oocytes were collected from 219 patients who had undergone a fresh IVM cycle. Oocyte maturation rates were similar between the groups (mean ± SD: 0.7 ± 0.2 vs. 0.6 ± 0.2, for vIVM and fIVM, respectively). Survival rate after warming was 59.8%. Fertilization and embryo cleavage rates per oocyte were significantly lower in the vIVM group. Clinical pregnancy (10.7 vs. 36.1%) and live birth rates (8.9 vs. 25.9%) per cycle were significantly lower in the vIVM group than those in the fIVM group (P = 0.005 and P < 0.001, respectively). Five healthy babies were born in the vIVM group. The reproductive potential of vitrified IVM oocytes is impaired. This injury likely occurs through vitrification and warming.

Mechanistic mathematical modelling of mercaptopurine effects on cell cycle of human acute lymphoblastic leukaemia cells

PubMed Central

Panetta, J C; Evans, W E; Cheok, M H

2006-01-01

The antimetabolite mercaptopurine (MP) is widely used to treat childhood acute lymphoblastic leukaemia (ALL). To study the dynamics of MP on the cell cycle, we incubated human T-cell leukaemia cell lines (Molt-4 sensitive and resistant subline and P12 resistant) with 10 μM MP and measured total cell count, cell cycle distribution, percent viable, percent apoptotic, and percent dead cells serially over 72 h. We developed a mathematical model of the cell cycle dynamics after treatment with MP and used it to show that the Molt-4 sensitive controls had a significantly higher rate of cells entering apoptosis (2.7-fold, P<0.00001) relative to the resistant cell lines. Additionally, when treated with MP, the sensitive cell line showed a significant increase in the rate at which cells enter apoptosis compared to its controls (2.4-fold, P<0.00001). Of note, the resistant cell lines had a higher rate of antimetabolite incorporation into the DNA of viable cells (>1.4-fold, P<0.01). Lastly, in contrast to the other cell lines, the Molt-4 resistant subline continued to cycle, though at a rate slower relative to its control, rather than proceed to apoptosis. This led to a larger S-phase block in the Molt-4 resistant cell line, but not a higher rate of cell death. Gene expression of apoptosis, cell cycle, and repair genes were consistent with mechanistic dynamics described by the model. In summary, the mathematical model provides a quantitative assessment to compare the cell cycle effects of MP in cells with varying degrees of MP resistance. PMID:16333308

Perfluoroalkyl Chemicals, Menstrual Cycle Length, and Fecundity: Findings from a Prospective Pregnancy Study

PubMed Central

Lum, Kirsten J.; Sundaram, Rajeshwari; Barr, Dana Boyd; Louis, Thomas A.; Louis, Germaine M. Buck

2016-01-01

Background Perfluoroalkyl substances have been associated with changes in menstrual cycle characteristics and fecundity, when modeled separately. However, these outcomes are biologically related, and we evaluate their joint association with exposure to perfluoroalkyl substances. Methods We recruited 501 couples from Michigan and Texas in 2005-2009 upon their discontinuing contraception and followed them until pregnancy or 12 months of trying. Female partners provided a serum sample upon enrollment and completed daily journals on menstruation, intercourse, and pregnancy test results. We measured seven perfluoroalkyl substances in serum using liquid-chromatography-tandem mass spectrometry. We assessed the association between perfluoroalkyl substances and menstrual cycle length using accelerated failure time models and between perfluoroalkyl substances and fecundity using a Bayesian joint modeling approach to incorporate cycle length. Results Menstrual cycles were 3% longer comparing women in the second versus first tertile of perfluorodecanoate (PFDeA; acceleration factor [AF]=1.03, 95% credible interval [CrI]=[1.00, 1.05]), but 2% shorter for women in the highest versus lowest tertile of perfluorooctanoic acid (PFOA) (AF=0.98, 95% CrI=[0.96, 1.00]). When accounting for cycle length, relevant covariates and remaining perfluoroalkyl substances, the probability of pregnancy was lower for women in second versus first tertile of PFNA (odds ratio [OR]=0.6, 95% CrI=[0.4, 1.0]) though not when comparing the highest versus lowest (OR=0.7, 95% CrI=[0.3, 1.1]) tertile. Conclusions In this prospective cohort study, we observed associations between two perfluoroalkyl substances and menstrual cycle length changes, and between select perfluoroalkyl substances and diminished fecundity at some (but not all) concentrations. PMID:27541842

Broadening GHG accounting with LCA: application to a waste management business unit.

PubMed

Fallaha, Sophie; Martineau, Geneviève; Bécaert, Valérie; Margni, Manuele; Deschênes, Louise; Samson, Réjean; Aoustin, Emmanuelle

2009-11-01

In an effort to obtain the most accurate climate change impact assessment, greenhouse gas (GHG) accounting is evolving to include life-cycle thinking. This study (1) identifies similarities and key differences between GHG accounting and life-cycle assessment (LCA), (2) compares them on a consistent basis through a case study on a waste management business unit. First, GHG accounting is performed. According to the GHG Protocol, annual emissions are categorized into three scopes: direct GHG emissions (scope 1), indirect emissions related to electricity, heat and steam production (scope 2) and other indirect emissions (scope 3). The LCA is then structured into a comparable framework: each LCA process is disaggregated into these three scopes, the annual operating activities are assessed, and the environmental impacts are determined using the IMPACT2002+ method. By comparing these two approaches it is concluded that both LCA and GHG accounting provide similar climate change impact results as the same major GHG contributors are determined for scope 1 emissions. The emissions from scope 2 appear negligible whereas emissions from scope 3 cannot be neglected since they contribute to around 10% of the climate change impact of the waste management business unit. This statement is strengthened by the fact that scope 3 generates 75% of the resource use damage and 30% of the ecosystem quality damage categories. The study also shows that LCA can help in setting up the framework for a annual GHG accounting by determining the major climate change contributors.

Assessing heterogeneity in soil nitrogen cycling: a plot-scale approach

Treesearch

Peter Baas; Jacqueline E. Mohan; David Markewitz; Jennifer D. Knoepp

2014-01-01

The high level of spatial and temporal heterogeneity in soil N cycling processes hinders our ability to develop an ecosystem-wide understanding of this cycle. This study examined how incorporating an intensive assessment of spatial variability for soil moisture, C, nutrients, and soil texture can better explain ecosystem N cycling at the plot scale. Five sites...

Ultrasonic Structural Health Monitoring to Assess the Integrity of Spinal Growing Rods In Vitro.

PubMed

Oetgen, Matthew E; Goodley, Addison; Yoo, Byungseok; Pines, Darryll J; Hsieh, Adam H

2016-01-01

Rod fracture is a common complication of growing rods and can result in loss of correction, patient discomfort, and unplanned revision surgery. The ability to quantitate rod integrity at each lengthening would be advantageous to avoid this complication. We investigate the feasibility of applying structural health monitoring to evaluate the integrity of growing rods in vitro. Single-rod titanium 4.5-mm growing rod constructs (n = 9), one screw proximally and one distally connected by in-line connectors, were assembled with pedicle screws fixed in polyethylene blocks. Proximal and distal ends were loaded and constructs subjected to cyclic axial compression (0-100 N at 1 Hz), with incrementally increasing maximum compressive loads of 10 N every 9k cycles until failure. Four piezoceramic transducers (PZTs) were mounted along the length the constructs to interrogate the integrity of the rods with an ultrasonic, guided lamb wave approach. Every 9k cycles, an 80 V excitatory voltage was applied to a PZT to generate high-frequency vibrations, which, after propagating through the construct, was detected by the remaining PZTs. Amplitude differences between pre- and postload waveform signals were calculated until rod failure. Average construct lifetime was 88,991 ± 13,398 cycles. All constructs failed due to rod fracture within 21 mm (mean = 15 ± 4.5 mm) of a screw or connector. Amplitude differences between pre- and postload increased in a stepwise fashion as constructs were cycled. Compared to baseline, we found a 1.8 ± 0.6-fold increase in amplitude 18k cycles before failure, a 2.2 ± 1.0-fold increase in amplitude 9k cycles before failure, and a 2.75 ± 1.5-fold increase in amplitude immediately before rod fracture. We describe a potential method for assessing the structural integrity of growing rods using ultrasonic structural health monitoring. These preliminary data demonstrate the ability of periodic rod assessment to detect structural changes in cycled growing rods, which appear to correspond to subclinical rod fatigue before rod fracture. Copyright © 2016 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.

Does gravidity influence the success of in vitro fertilization-embryo transfer cycles?

PubMed

Rabinson, Jacob; Bar-Hava, Itai; Meltcer, Simion; Zohav, Efraim; Anteby, Eyal; Orvieto, Raoul

2006-04-01

To evaluate the influence of gravidity on the results of in vitro fertilization (IVF)-embryo transfer (ET) cycles. All consecutive women aged <35 years admitted to our IVF unit from January 2002 to December 2004 were enrolled in the study. Only patients undergoing one of their first three IVF cycle attempts were included. Gravidity, ovarian stimulation characteristics, number of oocytes retrieved, number of embryo transferred and clinical pregnancy rate were assessed. Three hundred and forty-two consecutive IVF cycles were evaluated. One hundred and sixty-one cycles were from nulligravidas and 181 from women with a history of at least one previous clinical pregnancy. Forty-eight (29.8%) clinical pregnancies were observed in the nulligravida group and 56 (30.9%) in the gravida group. There were no differences between nulligravidas and gravidas in causes of infertility, length of ovarian stimulation, peak estradiol and progesterone levels, number of oocytes retrieved, fertilization rate and number of embryos transferred. Gravidas were significantly older (30.4 vs. 27.6 years, p < 0.001) and used more gonadotropin ampoules (36.1 vs. 31.8, p < 0.004) compared with the nulligravidas. Patient gravidity has no influence on the likelihood of achieving pregnancy in IVF-ET cycles.

Life Cycle Impact Assessment Research Developments and Needs

EPA Science Inventory

Life Cycle Impact Assessment (LCIA) developments are explained along with key publications which record discussions which comprised ISO 14042 and SETAC document development, UNEP SETAC Life Cycle Initiative research, and research from public and private research institutions. It ...

Maximal force and tremor changes across the menstrual cycle.

PubMed

Tenan, Matthew S; Hackney, Anthony C; Griffin, Lisa

2016-01-01

Sex hormones have profound effects on the nervous system in vitro and in vivo. The present study examines the effect of the menstrual cycle on maximal isometric force (MVC) and tremor during an endurance task. Nine eumenorrheic females participated in five study visits across their menstrual cycle. In each menstrual phase, an MVC and an endurance task to failure were performed. Tremor across the endurance task was quantified as the coefficient of variation in force and was assessed in absolute time and relative percent time to task failure. MVC decreases 23% from ovulation to the mid luteal phase of the menstrual cycle. In absolute time, the mid luteal phase has the highest initial tremor, though the early follicular phase has substantially higher tremor than other phases after 150 s of task performance. In relative time, the mid luteal phase has the highest level of tremor throughout the endurance task. Both MVC and tremor during an endurance task are modified by the menstrual cycle. Performance of tasks and sports which require high force and steadiness to exhaustion may be decreased in the mid luteal phase compared to other menstrual phases.

South Asian women with polycystic ovary syndrome exhibit greater sensitivity to gonadotropin stimulation with reduced fertilization and ongoing pregnancy rates than their Caucasian counterparts.

PubMed

Palep-Singh, M; Picton, H M; Vrotsou, K; Maruthini, D; Balen, A H

2007-10-01

Polycystic ovary syndrome (PCOS) is a heterogeneous syndrome. In vitro fertilization (IVF)/intracytoplasmic sperm injection (ICSI) is required for PCOS cases that are refractory to standard ovulation induction or have co-existing infertility factors in women with PCOS and Tubal factor subfertility. Assess ethnic variations in response to IVF/ICSI treatment. Observational Comparative study in a University hospital fertility clinic in women with PCOS and Tubal factor subfertility. Women with PCOS (Asians: AP=104; Caucasians: CP=220) and those with tubal factor infertility seeking fertility treatment were assessed (Asians: AC=84; Caucasians: CC=200). Six hundred and eight fresh IVF or ICSI cycles using long protocol of GnRHa suppression and resulting in a fresh embryo transfer were compared. The primary endpoint was to assess the dose of gonadotropins used in the cycles. The secondary outcomes were: total number of oocytes retrieved, fertilization and ongoing clinical pregnancy rates. We found that the South Asian women presented at a younger age for the management of sub-fertility. An extended stimulation phase and Caucasian ethnicity showed an inverse correlation with the number of oocytes retrieved in the PCOS subgroup. Caucasian ethnicity was associated with a higher fertilization rate however increase in body mass index (BMI) and the laboratory technique of IVF appeared to have a negative impact on fertilization rates in the PCOS subgroup. Commencing down regulation on day 1 of the cycles was negatively associated with fertilization rates in the tubal group. In terms of clinical pregnancy rates, the Caucasian PCOS had a 2.5 times (95% CI: 1.25-5) higher chance of an ongoing clinical pregnancy as compared with their Asian counterpart. Also, a unit increase in the basal FSH concentration reduced the odds of pregnancy by 18.6% (95% CI: 1.8-32.6%) in the PCOS group. The Asian PCOS have a greater sensitivity to gonadotropin stimulation with lower fertilization and ongoing clinical pregnancy rates as compared with their Caucasian counterparts.

Environmental implications of United States coal exports: a comparative life cycle assessment of future power system scenarios.

PubMed

Bohnengel, Barrett; Patiño-Echeverri, Dalia; Bergerson, Joule

2014-08-19

Stricter emissions requirements on coal-fired power plants together with low natural gas prices have contributed to a recent decline in the use of coal for electricity generation in the United States. Faced with a shrinking domestic market, many coal companies are taking advantage of a growing coal export market. As a result, U.S. coal exports hit an all-time high in 2012, fueled largely by demand in Asia. This paper presents a comparative life cycle assessment of two scenarios: a baseline scenario in which coal continues to be burned domestically for power generation, and an export scenario in which coal is exported to Asia. For the coal export scenario we focus on the Morrow Pacific export project being planned in Oregon by Ambre Energy that would ship 8.8 million tons of Powder River Basin (PRB) coal annually to Asian markets via rail, river barge, and ocean vessel. Air emissions (SOx, NOx, PM10 and CO2e) results assuming that the exported coal is burned for electricity generation in South Korea are compared to those of a business as usual case in which Oregon and Washington's coal plants, Boardman and Centralia, are retrofitted to comply with EPA emissions standards and continue their coal consumption. Findings show that although the environmental impacts of shipping PRB coal to Asia are significant, the combination of superior energy efficiency among newer South Korean coal-fired power plants and lower emissions from U.S. replacement of coal with natural gas could lead to a greenhouse gas reduction of 21% in the case that imported PRB coal replaces other coal sources in this Asian country. If instead PRB coal were to replace natural gas or nuclear generation in South Korea, greenhouse gas emissions per unit of electricity generated would increase. Results are similar for other air emissions such as SOx, NOx and PM. This study provides a framework for comparing energy export scenarios and highlights the importance of complete life cycle assessment in determining net emissions effects resulting from energy export projects and related policy decisions.

A framework for an alternatives assessment dashboard for evaluating chemical alternatives applied to flame retardants for electronic applications

PubMed Central

Martin, Todd M.

2017-01-01

The goal of alternatives assessment (AA) is to facilitate a comparison of alternatives to a chemical of concern, resulting in the identification of safer alternatives. A two stage methodology for comparing chemical alternatives was developed. In the first stage, alternatives are compared using a variety of human health effects, ecotoxicity, and physicochemical properties. Hazard profiles are completed using a variety of online sources and quantitative structure activity relationship models. In the second stage, alternatives are evaluated utilizing an exposure/risk assessment over the entire life cycle. Exposure values are calculated using screening-level near-field and far-field exposure models. The second stage allows one to more accurately compare potential exposure to each alternative and consider additional factors that may not be obvious from separate binned persistence, bioaccumulation, and toxicity scores. The methodology was utilized to compare phosphate-based alternatives for decabromodiphenyl ether (decaBDE) in electronics applications. PMID:29333139

Environmental Performance of Kettle Production: Product Life Cycle Assessment

NASA Astrophysics Data System (ADS)

Marcinkowski, Andrzej; Zych, Krzysztof

2017-12-01

The main objective of this paper is to compare the environmental impact caused by two different types of water boiling processes. The aim was achieved thanks to product life cycle assessment (LCA) conducted for stovetop and electric kettles. A literature review was carried out. A research model was worked out on the basis of data available in literature as well as additional experiments. In order to have a better opportunity to compare LCA results with reviewed literature, eco-indicator 99 assessment method was chosen. The functional unit included production, usage and waste disposal of each product (according to from cradle to grave approach) where the main function is boiling 3360 l of water during 4-year period of time. A very detailed life cycle inventory was carried out. The mass of components was determined with accuracy of three decimal places (0.001 g). The majority of environmental impact is caused by electricity or natural gas consumption during usage stage: 92% in case of the electric and kettle and 99% in case of stovetop one. Assembly stage contributed in 7% and 0.8% respectively. Uncertainty and sensitivity analyses took into consideration various waste scenario patterns as well as demand for transport. Environmental impact turned out to be strongly sensitive to a chosen pattern of energy delivery (electricity mix) which determined final comparison results. Basing on LCA results, some improvements of products were suggested. The boiling time optimization was pointed out for electric kettle's efficiency improvement. Obtained results can be used by manufacturers in order to improve their eco-effectiveness. Moreover, conclusions following the research part can influence the future choices of home appliances users.

Biomass pyrolysis for biochar or energy applications? A life cycle assessment.

PubMed

Peters, Jens F; Iribarren, Diego; Dufour, Javier

2015-04-21

The application of biochar as a soil amendment is a potential strategy for carbon sequestration. In this paper, a slow pyrolysis system for generating heat and biochar from lignocellulosic energy crops is simulated and its life-cycle performance compared with that of direct biomass combustion. The use of the char as biochar is also contrasted with alternative use options: cofiring in coal power plants, use as charcoal, and use as a fuel for heat generation. Additionally, the influence on the results of the long-term stability of the biochar in the soil, as well as of biochar effects on biomass yield, is evaluated. Negative greenhouse gas emissions are obtained for the biochar system, indicating a significant carbon abatement potential. However, this is achieved at the expense of lower energy efficiency and higher impacts in the other assessed categories when compared to direct biomass combustion. When comparing the different use options of the pyrolysis char, the most favorable result is obtained for char cofiring substituting fossil coal, even assuming high long-term stability of the char. Nevertheless, a high sensitivity to biomass yield increase is found for biochar systems. In this sense, biochar application to low-quality soils where high yield increases are expected would show a more favorable performance in terms of global warming.

Food waste minimization from a life-cycle perspective.

PubMed

Bernstad Saraiva Schott, A; Andersson, T

2015-01-01

This article investigates potentials and environmental impacts related to household food waste minimization, based on a case study in Southern Sweden. In the study, the amount of avoidable and unavoidable food waste currently being disposed of by households was assessed through waste composition analyses and the different types of avoidable food waste were classified. Currently, both avoidable and unavoidable food waste is either incinerated or treated through anaerobic digestion. A hypothetical scenario with no generation of avoidable food waste and either anaerobic digestion or incineration of unavoidable food waste was compared to the current situation using the life-cycle assessment method, limited to analysis of global warming potential (GWP). The results from the waste composition analyses indicate that an average of 35% of household food waste is avoidable. Minimization of this waste could result in reduction of greenhouse gas emissions of 800-1400 kg/tonne of avoidable food waste. Thus, a minimization strategy would result in increased avoidance of GWP compared to the current situation. The study clearly shows that although modern alternatives for food waste treatment can result in avoidance of GWP through nutrient and energy recovery, food waste prevention yields far greater benefits for GWP compared to both incineration and anaerobic digestion. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sleep homeostasis in the female rat during the estrous cycle.

PubMed

Schwierin, B; Borbély, A A; Tobler, I

1998-11-16

To investigate whether sleep homeostasis in the female rat is modulated by the estrous cycle, the vigilance states, EEG power spectra and cortical temperature (TCRT) were assessed on the basis of 4-day continuous recordings. A regulatory response was elicited by 6-h sleep deprivation (SD) during the proestrous (PRO) and the estrous (EST) day and compared to the baseline recordings. The vigilance states varied across the estrous cycle. In the PRO dark period the amount of sleep was reduced. The decrease in rapid-eye-movement (REM) sleep was already evident towards the end of the preceding light period, and an increased fragmentation of sleep was present throughout PRO. Compared to the other days of the estrous cycle, slow-wave activity (SWA; EEG power density 0.75-4.75 Hz) in nonREM (NREM) sleep was lower in PRO at the end of the light period and in the beginning of the dark period. High-frequency activity (HFA; EEG power density 10.25-25.0 Hz) was increased in the dark period of PRO. The SD performed during the first 6 h of the light period of PRO and EST enhanced SWA in NREM sleep and reduced sleep fragmentation during the subsequent 6 h. The extent and time course of the response to SD did not differ between the two phases of the estrous cycle. It is concluded that despite the marked baseline variations of the vigilance states and the EEG, homeostatic regulation is little affected by the estrous cycle. Copyright 1998 Elsevier Science B.V.

Embryonic development in human oocytes fertilized by split insemination

PubMed Central

Kim, Myo Sun; Kim, Jayeon; Youm, Hye Won; Park, Jung Yeon; Choi, Hwa Young

2015-01-01

Objective To compare the laboratory outcomes of intracytoplasmic sperm injection (ICSI) and conventional insemination using sibling oocytes in poor prognosis IVF cycles where ICSI is not indicated. Methods Couples undergoing IVF with following conditions were enrolled: history of more than 3 years of unexplained infertility, history of ≥3 failed intrauterine insemination, leukocytospermia or wide variation in semen analysis, poor oocyte quality, or ≥50% of embryos had poor quality in previous IVF cycle(s). Couples with severe male factor requiring ICSI were excluded. Oocytes were randomly assigned to the conventional insemination (conventional group) or ICSI (ICSI group). Fertilization rate (FR), total fertilization failure, and embryonic development at day 3 and day 5 were assessed. Results A total of 309 mature oocytes from 37 IVF cycles (32 couples) were obtained: 161 were assigned to conventional group and 148 to ICSI group. FR was significantly higher in the ICSI group compared to the conventional group (90.5% vs. 72.7%, P<0.001). Total fertilization failure occurred in only one cycle in conventional group. On day 3, the percentage of cleavage stage embryos was higher in ICSI group however the difference was marginally significant (P=0.055). In 11 cycles in which day 5 culture was attempted, the percentage of blastocyst (per cleaved embryo) was significantly higher in the ICSI group than the conventional group (55.9% vs. 25.9%, P=0.029). Conclusion Higher FR and more blastocyst could be achieved by ICSI in specific circumstances. Fertilization method can be tailored accordingly to improve IVF outcomes. PMID:26023671

Boron neutron capture therapy induces cell cycle arrest and cell apoptosis of glioma stem/progenitor cells in vitro.

PubMed

Sun, Ting; Zhang, Zizhu; Li, Bin; Chen, Guilin; Xie, Xueshun; Wei, Yongxin; Wu, Jie; Zhou, Youxin; Du, Ziwei

2013-08-06

Glioma stem cells in the quiescent state are resistant to clinical radiation therapy. An almost inevitable glioma recurrence is due to the persistence of these cells. The high linear energy transfer associated with boron neutron capture therapy (BNCT) could kill quiescent and proliferative cells. The present study aimed to evaluate the effects of BNCT on glioma stem/progenitor cells in vitro. The damage induced by BNCT was assessed using cell cycle progression, apoptotic cell ratio and apoptosis-associated proteins expression. The surviving fraction and cell viability of glioma stem/progenitor cells were decreased compared with differentiated glioma cells using the same boronophenylalanine pretreatment and the same dose of neutron flux. BNCT induced cell cycle arrest in the G2/M phase and cell apoptosis via the mitochondrial pathway, with changes in the expression of associated proteins. Glioma stem/progenitor cells, which are resistant to current clinical radiotherapy, could be effectively killed by BNCT in vitro via cell cycle arrest and apoptosis using a prolonged neutron irradiation, although radiosensitivity of glioma stem/progenitor cells was decreased compared with differentiated glioma cells when using the same dose of thermal neutron exposure and boronophenylalanine pretreatment. Thus, BNCT could offer an appreciable therapeutic advantage to prevent tumor recurrence, and may become a promising treatment in recurrent glioma.

Circadian Rhythm Shapes the Gut Microbiota Affecting Host Radiosensitivity.

PubMed

Cui, Ming; Xiao, Huiwen; Luo, Dan; Zhang, Xin; Zhao, Shuyi; Zheng, Qisheng; Li, Yuan; Zhao, Yu; Dong, Jiali; Li, Hang; Wang, Haichao; Fan, Saijun

2016-10-26

Modern lifestyles, such as shift work, nocturnal social activities, and jet lag, disturb the circadian rhythm. The interaction between mammals and the co-evolved intestinal microbiota modulates host physiopathological processes. Radiotherapy is a cornerstone of modern management of malignancies; however, it was previously unknown whether circadian rhythm disorder impairs prognosis after radiotherapy. To investigate the effect of circadian rhythm on radiotherapy, C57BL/6 mice were housed in different dark/light cycles, and their intestinal bacterial compositions were compared using high throughput sequencing. The survival rate, body weight, and food intake of mice in diverse cohorts were measured following irradiation exposure. Finally, the enteric bacterial composition of irradiated mice that experienced different dark/light cycles was assessed using 16S RNA sequencing. Intriguingly, mice housed in aberrant light cycles harbored a reduction of observed intestinal bacterial species and shifts of gut bacterial composition compared with those of the mice kept under 12 h dark/12 h light cycles, resulting in a decrease of host radioresistance. Moreover, the alteration of enteric bacterial composition of mice in different groups was dissimilar. Our findings provide novel insights into the effects of biological clocks on the gut bacterial composition, and underpin that the circadian rhythm influences the prognosis of patients after radiotherapy in a preclinical setting.

Three cycles of water deficit from seed to young plants of Moringa oleifera woody species improves stress tolerance.

PubMed

Rivas, Rebeca; Oliveira, Marciel T; Santos, Mauro G

2013-02-01

The main objective of this study was to assess whether recurring water stress occurring from seed germination to young plants of Moringa oleifera Lam. are able to mitigate the drought stress effects. Germination, gas exchange and biochemical parameters were analysed after three cycles of water deficit. Young plants were used 50 days after germination under three osmotic potentials (0.0, -0.3 and -0.4 MPa). For each germination treatment, control (irrigated) and stressed (10% of water control) plants were compared for a total of six treatments. There were two cycles of drought interspersed with 10 days of rehydration. The young plants of M. oleifera showed increased tolerance to repeated cycles of drought, maintaining high relative water content (RWC), high water use efficiency (WUE), increased photosynthetic pigments and increased activity of antioxidant enzymes. There was rapid recovery of the photosynthetic rate during the rehydration period. The stressed plants from the -0.3 and -0.4 MPa treatments showed higher tolerance compared to the control plants. The results suggest that seeds of M. oleifera subjected to mild water deficit have had increased the ability for drought tolerance when young plant. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

Changes in skeletal and cardiac muscle enzymes during the Scottish Coast to Coast Triathlon.

PubMed

Denvir, M A; Galloway, P J; Meighan, A S; Blyth, M; Alexander, C; Fleming, C; Frame, F

1999-04-01

While skeletal muscle injury is common after prolonged exercise, evidence in the literature supporting cardiac muscle injury is conflicting. Creatine kinase and cardiac troponin-I were measured, in 31 amateur athletes (25 male) before, and 12-24 hours after, a 300 km cycling/running/canoe triathlon event. A short questionnaire was used to assess level of fitness, training and previous experience. Creatine kinase levels were greater after the 45 km cross-country run compared with after a 155 km road cycle (60.5 +/- 62.8 iu/L/kg vs 19.3 +/- 9.6 iu/kg, P = 0.03). Individuals performing running and cycling events consecutively had creatine kinase similar to those observed after running alone (50.2 +/- 53.8 iu/L/kg vs 60.5 +/- 62.8 iu/L/kg, P = 0.55). Cardiac troponin-I was elevated above the normal range (0.1 ng/L) in six athletes (four in running and cycling events, one in the running and one in the cycling event). We conclude that running produces significantly more skeletal muscle injury than cycling and that strenuous endurance exercise involving running and cycling in amateur trained athletes is associated with release of cardiac specific enzymes. The functional and longer term consequences of this require further study.

Life cycle greenhouse gas emissions and freshwater consumption of Marcellus shale gas.

PubMed

Laurenzi, Ian J; Jersey, Gilbert R

2013-05-07

We present results of a life cycle assessment (LCA) of Marcellus shale gas used for power generation. The analysis employs the most extensive data set of any LCA of shale gas to date, encompassing data from actual gas production and power generation operations. Results indicate that a typical Marcellus gas life cycle yields 466 kg CO2eq/MWh (80% confidence interval: 450-567 kg CO2eq/MWh) of greenhouse gas (GHG) emissions and 224 gal/MWh (80% CI: 185-305 gal/MWh) of freshwater consumption. Operations associated with hydraulic fracturing constitute only 1.2% of the life cycle GHG emissions, and 6.2% of the life cycle freshwater consumption. These results are influenced most strongly by the estimated ultimate recovery (EUR) of the well and the power plant efficiency: increase in either quantity will reduce both life cycle freshwater consumption and GHG emissions relative to power generated at the plant. We conclude by comparing the life cycle impacts of Marcellus gas and U.S. coal: The carbon footprint of Marcellus gas is 53% (80% CI: 44-61%) lower than coal, and its freshwater consumption is about 50% of coal. We conclude that substantial GHG reductions and freshwater savings may result from the replacement of coal-fired power generation with gas-fired power generation.

Reproductive Health Assessment of Female Elephants in North American Zoos and Association of Husbandry Practices with Reproductive Dysfunction in African Elephants (Loxodonta africana)

PubMed Central

Meehan, Cheryl L.; Hogan, Jennifer N.; Morfeld, Kari A.; Carlstead, Kathy

2016-01-01

As part of a multi-institutional study of zoo elephant welfare, we evaluated female elephants managed by zoos accredited by the Association of Zoos and Aquariums and applied epidemiological methods to determine what factors in the zoo environment are associated with reproductive problems, including ovarian acyclicity and hyperprolactinemia. Bi-weekly blood samples were collected from 95 African (Loxodonta africana) and 75 Asian (Elephas maximus) (8–55 years of age) elephants over a 12-month period for analysis of serum progestogens and prolactin. Females were categorized as normal cycling (regular 13- to 17-week cycles), irregular cycling (cycles longer or shorter than normal) or acyclic (baseline progestogens, <0.1 ng/ml throughout), and having Low/Normal (<14 or 18 ng/ml) or High (≥14 or 18 ng/ml) prolactin for Asian and African elephants, respectively. Rates of normal cycling, acyclicity and irregular cycling were 73.2, 22.5 and 4.2% for Asian, and 48.4, 37.9 and 13.7% for African elephants, respectively, all of which differed between species (P < 0.05). For African elephants, univariate assessment found that social isolation decreased and higher enrichment diversity increased the chance a female would cycle normally. The strongest multi-variable models included Age (positive) and Enrichment Diversity (negative) as important factors of acyclicity among African elephants. The Asian elephant data set was not robust enough to support multi-variable analyses of cyclicity status. Additionally, only 3% of Asian elephants were found to be hyperprolactinemic as compared to 28% of Africans, so predictive analyses of prolactin status were conducted on African elephants only. The strongest multi-variable model included Age (positive), Enrichment Diversity (negative), Alternate Feeding Methods (negative) and Social Group Contact (positive) as predictors of hyperprolactinemia. In summary, the incidence of ovarian cycle problems and hyperprolactinemia predominantly affects African elephants, and increases in social stability and feeding and enrichment diversity may have positive influences on hormone status. PMID:27416141

Reproductive Health Assessment of Female Elephants in North American Zoos and Association of Husbandry Practices with Reproductive Dysfunction in African Elephants (Loxodonta africana).

PubMed

Brown, Janine L; Paris, Stephen; Prado-Oviedo, Natalia A; Meehan, Cheryl L; Hogan, Jennifer N; Morfeld, Kari A; Carlstead, Kathy

2016-01-01

As part of a multi-institutional study of zoo elephant welfare, we evaluated female elephants managed by zoos accredited by the Association of Zoos and Aquariums and applied epidemiological methods to determine what factors in the zoo environment are associated with reproductive problems, including ovarian acyclicity and hyperprolactinemia. Bi-weekly blood samples were collected from 95 African (Loxodonta africana) and 75 Asian (Elephas maximus) (8-55 years of age) elephants over a 12-month period for analysis of serum progestogens and prolactin. Females were categorized as normal cycling (regular 13- to 17-week cycles), irregular cycling (cycles longer or shorter than normal) or acyclic (baseline progestogens, <0.1 ng/ml throughout), and having Low/Normal (<14 or 18 ng/ml) or High (≥14 or 18 ng/ml) prolactin for Asian and African elephants, respectively. Rates of normal cycling, acyclicity and irregular cycling were 73.2, 22.5 and 4.2% for Asian, and 48.4, 37.9 and 13.7% for African elephants, respectively, all of which differed between species (P < 0.05). For African elephants, univariate assessment found that social isolation decreased and higher enrichment diversity increased the chance a female would cycle normally. The strongest multi-variable models included Age (positive) and Enrichment Diversity (negative) as important factors of acyclicity among African elephants. The Asian elephant data set was not robust enough to support multi-variable analyses of cyclicity status. Additionally, only 3% of Asian elephants were found to be hyperprolactinemic as compared to 28% of Africans, so predictive analyses of prolactin status were conducted on African elephants only. The strongest multi-variable model included Age (positive), Enrichment Diversity (negative), Alternate Feeding Methods (negative) and Social Group Contact (positive) as predictors of hyperprolactinemia. In summary, the incidence of ovarian cycle problems and hyperprolactinemia predominantly affects African elephants, and increases in social stability and feeding and enrichment diversity may have positive influences on hormone status.

Clinical Course of Oxaliplatin-Induced Neuropathy: Results From the Randomized Phase III Trial N08CB (Alliance)

PubMed Central

Pachman, Deirdre R.; Qin, Rui; Seisler, Drew K.; Smith, Ellen M.L.; Beutler, Andreas S.; Ta, Lauren E.; Lafky, Jacqueline M.; Wagner-Johnston, Nina D.; Ruddy, Kathryn J.; Dakhil, Shaker; Staff, Nathan P.; Grothey, Axel; Loprinzi, Charles L.

2015-01-01

Purpose Given that the clinical course of oxaliplatin-induced neuropathy is not well defined, the current study was performed to better understand clinical parameters associated with its presentation. Methods Acute and chronic neuropathy was evaluated in patients receiving adjuvant FOLFOX (fluorouracil, leucovorin, and oxaliplatin) on study N08CB (North Central Cancer Treatment Group, Alliance). Acute neuropathy was assessed by having patients complete daily questionnaires for 6 days with each cycle of FOLFOX. Before each dose of FOLFOX and as long as 18 months after chemotherapy cessation, chronic neurotoxicity was assessed with use of the 20-item, European Organisation for Research and Treatment of Cancer quality-of-life questionnaire for patients with chemotherapy-induced peripheral neuropathy. Results Three hundred eight (89%) of the 346 patients had at least one symptom of acute neuropathy with the first cycle of FOLFOX; these symptoms included sensitivity to touching cold items (71%), sensitivity to swallowing cold items (71%), throat discomfort (63%), or muscle cramps (42%). Acute symptoms peaked at day 3 and improved, although they did not always resolve completely between treatments. These symptoms were about twice as severe in cycles 2 through 12 as they were in cycle 1. For chronic neurotoxicity, tingling was the most severe symptom, followed by numbness and then pain. During chemotherapy, symptoms in the hands were more prominent than they were in the feet; by 18 months, symptoms were more severe in the feet than they were in the hands. Patients with more severe acute neuropathy during the first cycle of therapy experienced more chronic sensory neurotoxicity (P < .0001). Conclusion Acute oxaliplatin-induced neuropathy symptoms do not always completely resolve between treatment cycles and are only half as severe on the first cycle as compared with subsequent cycles. There is a correlation between the severities of acute and chronic neuropathies. PMID:26282635

Comparative analysis of economic models in selected solar energy computer programs

NASA Astrophysics Data System (ADS)

Powell, J. W.; Barnes, K. A.

1982-01-01

The economic evaluation models in five computer programs widely used for analyzing solar energy systems (F-CHART 3.0, F-CHART 4.0, SOLCOST, BLAST, and DOE-2) are compared. Differences in analysis techniques and assumptions among the programs are assessed from the point of view of consistency with the Federal requirements for life cycle costing (10 CFR Part 436), effect on predicted economic performance, and optimal system size, case of use, and general applicability to diverse systems types and building types. The FEDSOL program developed by the National Bureau of Standards specifically to meet the Federal life cycle cost requirements serves as a basis for the comparison. Results of the study are illustrated in test cases of two different types of Federally owned buildings: a single family residence and a low rise office building.

The influence of the menstrual cycle on energy balance and taste preference in Asian Chinese women.

PubMed

Elliott, Sarah A; Ng, Janet; Leow, Melvin Khee-Shing; Henry, Christiani J K

2015-12-01

In Caucasian women, research has shown that energy balance and taste preference change throughout the menstrual cycle. However, the contributory role of the menstrual cycle to obesity and insulin resistance among Asian women remains unclear. We investigate the impact of the menstrual cycle on energy balance and taste preference in Singaporean Chinese females. Thirty-one healthy young Chinese female subjects with regular menstrual cycles were recruited. Anthropometrics, body composition, energy intake, resting metabolic rate, premenstrual syndrome (PMS) severity and taste preference to sucrose were assessed during three phases (menses, follicular and luteal), over one (N = 18) to two (N = 13) menstrual cycles. For all subjects (N = 31), we found significant reductions in energy, fat intake (p < 0.05) and taste preference for sucrose (p < 0.05) in the luteal phase compared to early follicular phase as far as Cycle 1 is concerned. No significant differences were observed for carbohydrate and protein intake as well as PMS score. In those evaluated for two full cycles (N = 13), we found that taste preference for sucrose and PMS score were significantly higher in the menstrual phase in Cycle 2 (p < 0.05). No significant differences were observed in energy and macronutrient intake throughout Cycle 2. RMR was similar across the three phases. However, non-significant cyclic variations were noted within and between the cycles. Cyclic variations in energy intake and expenditure contributed by sensory and behavioural changes occur during the menstrual cycle. Whether this contributes to cyclic weight gain is speculative and remains to be proven. Further research in non-Caucasians spanning more than one menstrual cycle is needed to establish the impact of the menstrual cycle on taste preference and energy balance.

The Impact of Continuous and Interval Cycle Exercise on Affect and Enjoyment

ERIC Educational Resources Information Center

Kilpatrick, Marcus W.; Greeley, Samuel J.; Collins, Larry H.

2015-01-01

Rates of physical activity remain low despite public health efforts. One form of physical activity that provides significant physiological benefit but has not been evaluated in terms of affective and enjoyment responses is interval exercise. Purpose: The purpose of this study was to compare affect and enjoyment assessed before, during, and after…

Using Performance Tasks to Improve Quantitative Reasoning in an Introductory Mathematics Course

ERIC Educational Resources Information Center

Kruse, Gerald; Drews, David

2013-01-01

A full-cycle assessment of our efforts to improve quantitative reasoning in an introductory math course is described. Our initial iteration substituted more open-ended performance tasks for the active learning projects than had been used. Using a quasi-experimental design, we compared multiple sections of the same course and found non-significant…

Comparative durability of timber bridges in the USA

Treesearch

James P. Wacker; Brian K. Brashaw

2017-01-01

As engineers begin to utilize life-cycle-cost design approaches for timber bridges, there is a necessity for more reliable data about their durability and expected service life. This paper summarizes a comprehensive effort to assess the current condition of more than one hundred timber highway bridge superstructures throughout the United States. This national study was...

The cleaner, the greener? Product sustainability assessment of the biomimetic façade paint Lotusan® in comparison to the conventional façade paint Jumbosil®

PubMed Central

Antony, Florian; Grießhammer, Rainer; Speck, Thomas

2016-01-01

Background: The debate on the question whether biomimetics has a specific potential to contribute to sustainability is discussed among scientists, business leaders, politicians and those responsible for project funding. The objective of this paper is to contribute to this controversial debate by presenting the sustainability assessment of one of the most well-known and most successful biomimetic products: the façade paint Lotusan®. Results: As a first step it has been examined and verified that the façade paint Lotusan® is correctly defined as a biomimetic product. Secondly, Lotusan® has been assessed and compared to a conventional façade paint within the course of a detailed product sustainability assessment (PROSA). For purposes of comparison, the façade paint Jumbosil® was chosen as reference for a conventional paint available on the market. The benefit analysis showed that both paints fulfil equally well the requirements of functional utility. With respect to the symbolic utility, Lotusan® has a particular added aesthetic value by the preservation of the optical quality over the life cycle. Within the social analysis no substantial differences between the two paints could be found regarding the handling and disposal of the final products. Regarding the life-cycle cost, Lotusan® is the more expensive product. However, the higher investment cost for a Lotusan®-based façade painting are more than compensated by the longer life time, resulting in both reduced overall material demand and lower labour cost. In terms of the life-cycle impact assessment, it can be ascertained that substantial differences between the paints arise from the respective service life, which are presented in terms of four scenario analyses. Conclusion: In summary, the biomimetic façade paint Lotusan® has been identified as a cost-effective and at the same time resource-saving product. Based on the underlying data and assumptions it could be demonstrated that Lotusan®-based façade paintings have a comparatively low overall impact on the environment. Summarizing our results, it can be emphasized that Lotusan® is the more favourable product compared to Jumbosil® according to sustainability aspects. PMID:28144557

The cleaner, the greener? Product sustainability assessment of the biomimetic façade paint Lotusan® in comparison to the conventional façade paint Jumbosil®.

PubMed

Antony, Florian; Grießhammer, Rainer; Speck, Thomas; Speck, Olga

2016-01-01

Background: The debate on the question whether biomimetics has a specific potential to contribute to sustainability is discussed among scientists, business leaders, politicians and those responsible for project funding. The objective of this paper is to contribute to this controversial debate by presenting the sustainability assessment of one of the most well-known and most successful biomimetic products: the façade paint Lotusan ® . Results: As a first step it has been examined and verified that the façade paint Lotusan ® is correctly defined as a biomimetic product. Secondly, Lotusan ® has been assessed and compared to a conventional façade paint within the course of a detailed product sustainability assessment (PROSA). For purposes of comparison, the façade paint Jumbosil ® was chosen as reference for a conventional paint available on the market. The benefit analysis showed that both paints fulfil equally well the requirements of functional utility. With respect to the symbolic utility, Lotusan ® has a particular added aesthetic value by the preservation of the optical quality over the life cycle. Within the social analysis no substantial differences between the two paints could be found regarding the handling and disposal of the final products. Regarding the life-cycle cost, Lotusan ® is the more expensive product. However, the higher investment cost for a Lotusan ® -based façade painting are more than compensated by the longer life time, resulting in both reduced overall material demand and lower labour cost. In terms of the life-cycle impact assessment, it can be ascertained that substantial differences between the paints arise from the respective service life, which are presented in terms of four scenario analyses. Conclusion: In summary, the biomimetic façade paint Lotusan ® has been identified as a cost-effective and at the same time resource-saving product. Based on the underlying data and assumptions it could be demonstrated that Lotusan ® -based façade paintings have a comparatively low overall impact on the environment. Summarizing our results, it can be emphasized that Lotusan ® is the more favourable product compared to Jumbosil ® according to sustainability aspects.

Is objective and accurate cognitive assessment across the menstrual cycle possible? A feasibility study

PubMed Central

Neill, Jo; Scally, Andy; Tuffnell, Derek; Marshall, Kay

2015-01-01

Objectives: Variation in plasma hormone levels influences the neurobiology of brain regions involved in cognition and emotion processing. Fluctuations in hormone levels across the menstrual cycle could therefore alter cognitive performance and wellbeing; reports have provided conflicting results, however. The aim of this study was to assess whether objective assessment of cognitive performance and self-reported wellbeing during the follicular and luteal phases of the menstrual cycle is feasible and investigate the possible reasons for variation in effects previously reported. Methods: The Cambridge Neuropsychological Test Automated Battery and Edinburgh Postnatal Depression Scale were used to assess the cognitive performance and wellbeing of 12 women. Data were analysed by self-reported and hormone-estimated phases of the menstrual cycle. Results: Recruitment to the study and assessment of cognition and wellbeing was without issue. Plasma hormone and peptide estimation showed substantial individual variation and suggests inaccuracy in self-reported menstrual phase estimation. Conclusion: Objective assessment of cognitive performance and self-assessed wellbeing across the menstrual cycle is feasible. Grouping data by hormonal profile rather by self-reported phase estimation may influence phase-mediated results. Future studies should use plasma hormone and peptide profiles to estimate cycle phase and group data for analyses. PMID:26770760

Menstrual cycle phase and single tablet antiretroviral medication adherence in women with HIV.

PubMed

Hessol, Nancy A; Holman, Susan; Minkoff, Howard; Cohen, Mardge H; Golub, Elizabeth T; Kassaye, Seble; Karim, Roksana; Sosanya, Oluwakemi; Shaheen, Christopher; Merhi, Zaher

2016-01-01

Suboptimal adherence to antiretroviral (ARV) therapy among HIV-infected individuals is associated with increased risk of progression to AIDS and the development of HIV resistance to ARV medications. To examine whether the luteal phase of the menstrual cycle is independently associated with suboptimal adherence to single tablet regimen (STR) ARV medication, data were analyzed from a multicenter cohort study of HIV-infected women who reported regular menstrual cycles and were taking an STR. In a cross-sectional analysis, suboptimal adherence to an STR among women in their follicular phase was compared with suboptimal adherence among women in their luteal phase. In two-way crossover analyses, whereby the same woman was assessed for STR medication adherence in both her follicular and luteal phases, the estimated exact conditional odds of non-adherence to an STR was measured. In adjusted logistic regression analysis of the cross-sectional data (N=327), women with ≤12 years of education were more than three times more likely to have suboptimal adherence (OR=3.6, p=.04) compared to those with >12 years of education. Additionally, women with Center for Epidemiological Studies Depression Scale (CES-D) scores ≥23 were 2.5-times more likely to have suboptimal adherence (OR=2.6, p=.02) compared to those with CES-D scores <23. In conditional logistic regression analyses of the crossover data (N=184), having childcare responsibilities was associated with greater odds of ≤95% adherence. Menstrual cycle phase was not associated with STR adherence in either the cross-sectional or crossover analyses. The lack of association between phase of the menstrual cycle and adherence to an STR in HIV-infected women means attention can be given to other more important risk factors for suboptimal adherence, such as depression, level of education, and childcare responsibilities.

Development and application of basis database for materials life cycle assessment in china

NASA Astrophysics Data System (ADS)

Li, Xiaoqing; Gong, Xianzheng; Liu, Yu

2017-03-01

As the data intensive method, high quality environmental burden data is an important premise of carrying out materials life cycle assessment (MLCA), and the reliability of data directly influences the reliability of the assessment results and its application performance. Therefore, building Chinese MLCA database is the basic data needs and technical supports for carrying out and improving LCA practice. Firstly, some new progress on database which related to materials life cycle assessment research and development are introduced. Secondly, according to requirement of ISO 14040 series standards, the database framework and main datasets of the materials life cycle assessment are studied. Thirdly, MLCA data platform based on big data is developed. Finally, the future research works were proposed and discussed.

Assessment of Material Solutions of Multi-level Garage Structure Within Integrated Life Cycle Design Process

NASA Astrophysics Data System (ADS)

Wałach, Daniel; Sagan, Joanna; Gicala, Magdalena

2017-10-01

The paper presents an environmental and economic analysis of the material solutions of multi-level garage. The construction project approach considered reinforced concrete structure under conditions of use of ordinary concrete and high-performance concrete (HPC). Using of HPC allowed to significant reduction of reinforcement steel, mainly in compression elements (columns) in the construction of the object. The analysis includes elements of the methodology of integrated lice cycle design (ILCD). By making multi-criteria analysis based on established weight of the economic and environmental parameters, three solutions have been evaluated and compared within phase of material production (information modules A1-A3).

Use of life cycle assessments to evaluate the environmental footprint of contaminated sediment remediation.

PubMed

Sparrevik, Magnus; Saloranta, Tuomo; Cornelissen, Gerard; Eek, Espen; Fet, Annik Magerholm; Breedveld, Gijs D; Linkov, Igor

2011-05-15

Ecological and human risks often drive the selection of remedial alternatives for contaminated sediments. Traditional human and ecological risk assessment (HERA) includes assessing risk for benthic organisms and aquatic fauna associated with exposure to contaminated sediments before and after remediation as well as risk for human exposure but does not consider the environmental footprint associated with implementing remedial alternatives. Assessment of environmental effects over the whole life cycle (i.e., Life Cycle Assessment, LCA) could complement HERA and help in selecting the most appropriate sediment management alternative. Even though LCA has been developed and applied in multiple environmental management cases, applications to contaminated sediments and marine ecosystems are in general less frequent. This paper implements LCA methodology for the case of the polychlorinated dibenzo-p-dioxins and -furans (PCDD/F)-contaminated Grenland fjord in Norway. LCA was applied to investigate the environmental footprint of different active and passive thin-layer capping alternatives as compared to natural recovery. The results showed that capping was preferable to natural recovery when analysis is limited to effects related to the site contamination. Incorporation of impacts related to the use of resources and energy during the implementation of a thin layer cap increase the environmental footprint by over 1 order of magnitude, making capping inferior to the natural recovery alternative. Use of biomass-derived activated carbon, where carbon dioxide is sequestered during the production process, reduces the overall environmental impact to that of natural recovery. The results from this study show that LCA may be a valuable tool for assessing the environmental footprint of sediment remediation projects and for sustainable sediment management.

Crash Attenuator Data Collection and Life Cycle Tool Development

DOT National Transportation Integrated Search

2014-06-14

This research study was aimed at data collection and development of a decision support tool for life cycle cost assessment of crash attenuators. Assessing arrenuator life cycle costs based on in-place expected costs and not just the initial cost enha...

Garvin Heath | NREL

Science.gov Websites

& Impacts Analysis Group in the Strategic Energy Analysis Center. Areas of Expertise Life cycle environmental impacts of energy technologies, including externalities Life cycle assessment Sustainability ;Life Cycle Assessment of a Parabolic Trough Concentrating Solar Power Plant and the Impacts of Key

Fatigue of reinforcing bars during hydro-demolition

NASA Astrophysics Data System (ADS)

Hyland, C. W. K.; Ouwejan, A.

2017-05-01

Reinforcing steel fractured during hydro-demolition of a reinforced concrete pier head due to low cycle flexural fatigue from vibration caused by impact of the high pressure water jet on the exposed length of the bars. Research into the fatigue performance of steel reinforcing steel tends to focus on the high cycle axial performance in reinforced concrete members and re-bending behaviour. However with the increasing use of hydro-demolition of concrete structures as part of remediation works care is required to ensure the steel reinforcement exposed to the high pressure jet of water is not going to suffer relatively low cycle flexural damage that may compromise the designed performance of the completed reinforced concrete structure. This paper describes the failure assessment, fatigue analysis, and metallographic examination that was undertaken. It was found that the rib to flank transition radius on the reinforcement steel was small enough to cause a significant stress concentration effect and was the location of fatigue crack growth. A relatively simple analysis using the maximum unrestrained cantilevered bar length and force exerted by the water jet was used to calculate the maximum expected bending moment. This was compared to the bending capacity at initiation of yielding at the rib flank transition accounting for stress concentration effects. This showed that the observed cyclic reversing ductile crack growth and fracture of the H25 bars was consistent with the loading applied. A method is proposed based on these observations to assess suitable limits for unrestrained bar lengths or maximum working offset of the water jet from the point of bar restraint when undertaking hydro-demolition work. The fatigue critical performance requirements of AS/NZS4671 500E bars are also therefore compared with those of BS4449:2005 and PN EN/ISO 15630-1:2011 for comparable 500C bars

Application of force-velocity cycle ergometer test and vertical jump tests in the functional assessment of karate competitor.

PubMed

Ravier, G; Grappe, F; Rouillon, J D

2004-12-01

The aim of this study was to analyze the links between tests performances (vertical jump and force-velocity sprint on cycle ergometer) and 2 different karate level groups in order to propose a test battery adjusted to karate. Twenty-two karate competitors (10 national junior team (IJ) and 12 national competition level (NL)) performed 4 maximal squat jumps (SJ), 4 maximal counter movement jumps (CMJ) on an ergojump and 3 8-s sprints on a friction braked cycle ergometer (friction loads of 0.5, 0.7, 0.9 N x kg(-1)). The maximal theoretical force (F(0)) and velocity (V(0)), the maximal power output (P(max)) and the optimal pedalling velocity (V(opt)) were derived from both the force -- velocity and the power -- velocity relationships plotted from all the 3 friction loads data. V(0), F(0), V(opt), P(max) and the best SJ and CMJ, were compared between IJ and NL groups. The IJ group was characterised by significantly higher values of V(0) (+13%) and SJ (+14.3%) compared to NL group, whereas no significant difference was observed between groups for F(0). Thus, karate performance would depend on maximal velocity and explosive strength. In addition, V(opt) was significantly higher in IJ group compared to NL group (135.4 rpm vs 119.2 rpm, p<0.001). Although based upon indirect evidence, these results accounted for mechanical functional capabilities of experts which could be particularly valuable when monitoring training of karate competitor. A force-velocity and a vertical jump tests may be applied in the functional assessment of karate competitor.

Environmental assessment of biofuel pathways in Ile de France based on ecosystem modeling.

PubMed

Gabrielle, Benoît; Gagnaire, Nathalie; Massad, Raia Silvia; Dufossé, Karine; Bessou, Cécile

2014-01-01

The objective of the work reported here was to reduce the uncertainty on the greenhouse gas balances of biofuels using agro-ecosystem modeling at a high resolution over the Ile-de-France region in Northern France. The emissions simulated during the feedstock production stage were input to a life-cycle assessment of candidate biofuel pathways: bioethanol from wheat, sugar-beet and miscanthus, and biodiesel from oilseed rape. Compared to the widely-used methodology based on fixed emission factors, ecosystem modeling lead to 55-70% lower estimates for N2O emissions, emphasizing the importance of regional factors. The life-cycle GHG emissions of first-generation biofuels were 50-70% lower than fossil-based equivalents, and 85% lower for cellulosic ethanol. When including indirect land-use change effects, GHG savings became marginal for biodiesel and wheat ethanol, but were positive due to direct effects for cellulosic ethanol. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparative life cycle assessment and financial analysis of mixed culture polyhydroxyalkanoate production.

PubMed

Gurieff, Nicholas; Lant, Paul

2007-12-01

A life cycle assessment and financial analysis of mixed culture PHA (PHA(MC)) and biogas production was undertaken based on treating an industrial wastewater. Internal rate of return (IRR) and non-renewable CO(2)eq emissions were used to quantify financial viability and environmental impact. PHA(MC) was preferable to biogas production for treating the specified industrial effluent. PHA(MC) was also financially attractive in comparison to pure culture PHA production. Both PHA production processes had similar environmental impacts that were significantly lower than HDPE production. A large potential for optimisation exists for the PHA(MC) process as financial and environmental costs were primarily due to energy use for downstream processing. Under the conditions used in this work PHA(MC) was shown to be a viable biopolymer production process and an effective industrial wastewater treatment technology. This is the first study of its kind and provides valuable insight into the PHA(MC) process.

An Assessment of Alternate Thermal Protection Systems for the Space Shuttle Orbiter. Volume 1; Executive Summary

NASA Technical Reports Server (NTRS)

Hays, D.

1982-01-01

Alternate thermal protection system (TPS) concepts to the Space Shuttle Orbiter were assessed. Metallic, ablator, and carbon-carbon concepts which are the result of some previous design, manufacturing and testing effort were considered. Emphasis was placed on improved TPS durability, which could potentially reduce life cycle costs and improve Orbiter operational characteristics. Integrated concept/orbiter point designs were generated and analyzed on the basis of Shuttle design environments and criteria. A merit function evaluation methodology based on mission impact, life cycle costs, and risk was developed to compare the candidate concepts and to identify the best alternate. Voids and deficiencies in the technology were identified, along with recommended activities to overcome them. Finally, programmatic plans, including ROM costs and schedules, were developed for all activities required to bring the selected alternate system up to operational readiness.

Life Cycle Assessment of high ligno-cellulosic biomass pyrolysis coupled with anaerobic digestion.

PubMed

Righi, Serena; Bandini, Vittoria; Marazza, Diego; Baioli, Filippo; Torri, Cristian; Contin, Andrea

2016-07-01

A Life Cycle Assessment is conducted on pyrolysis coupled to anaerobic digestion to treat corn stovers and to obtain bioenergy and biochar. The analysis takes into account the feedstock treatment process, the fate of products and the indirect effects due to crop residue removal. The biochar is considered to be used as solid fuel for coal power plants or as soil conditioner. All results are compared with a corresponding fossil-fuel-based scenario. It is shown that the proposed system always enables relevant primary energy savings of non-renewable sources and a strong reduction of greenhouse gases emissions without worsening the abiotic resources depletion. Conversely, the study points out that the use of corn stovers for mulch is critical when considering acidification and eutrophication impacts. Therefore, removal of corn stovers from the fields must be planned carefully. Copyright © 2016. Published by Elsevier Ltd.

Consistency of seven different GNSS global ionospheric mapping techniques during one solar cycle

NASA Astrophysics Data System (ADS)

Roma-Dollase, David; Hernández-Pajares, Manuel; Krankowski, Andrzej; Kotulak, Kacper; Ghoddousi-Fard, Reza; Yuan, Yunbin; Li, Zishen; Zhang, Hongping; Shi, Chuang; Wang, Cheng; Feltens, Joachim; Vergados, Panagiotis; Komjathy, Attila; Schaer, Stefan; García-Rigo, Alberto; Gómez-Cama, José M.

2018-06-01

In the context of the International GNSS Service (IGS), several IGS Ionosphere Associated Analysis Centers have developed different techniques to provide global ionospheric maps (GIMs) of vertical total electron content (VTEC) since 1998. In this paper we present a comparison of the performances of all the GIMs created in the frame of IGS. Indeed we compare the classical ones (for the ionospheric analysis centers CODE, ESA/ESOC, JPL and UPC) with the new ones (NRCAN, CAS, WHU). To assess the quality of them in fair and completely independent ways, two assessment methods are used: a direct comparison to altimeter data (VTEC-altimeter) and to the difference of slant total electron content (STEC) observed in independent ground reference stations (dSTEC-GPS). The main conclusion of this study, performed during one solar cycle, is the consistency of the results between so many different GIM techniques and implementations.

Towards life cycle sustainability assessent of cities. A review of background knowledge.

PubMed

Albertí, Jaume; Balaguera, Alejandra; Brodhag, Christian; Fullana-I-Palmer, Pere

2017-12-31

This article analyses whether existing LCA and sustainability methods can be used in the assessment of a city or an urban region. The approach is performed through the review of current existing LCA-based and sustainability standards and guidelines. A focus is put into those LCA-based standards specially designed for the built environment. Moreover, a review of non-LCA based standards, indices and guides for the assessment of the sustainability of countries, cities or urban regions is done. The purpose is to check if these assessment tools can provide good results in the absence of LCA-based assessments for cities and urban regions. This review demonstrates the lack of consensus in the definition of both, the city and its boundaries, which hinders the development of useful sustainability standards. Furthermore, it is concluded that current sustainability assessment tools miss, at least, one of these aspects: (i) holistic point of view, (ii) focus on various environmental impacts, (iii) a Life Cycle (LC) perspective, and (iv) the possibility to compare the results among different cities or urban regions. From the LCA perspective, the deficiencies found also include the need for a definition of the function, functional unit (FU), and reference flow (RF) of neighbourhoods, cities, and urban regions. Copyright © 2017 Elsevier B.V. All rights reserved.

Correlates of walking and cycling for transport and recreation: factor structure, reliability and behavioural associations of the perceptions of the environment in the neighbourhood scale (PENS)

PubMed Central

2013-01-01

Background Emerging evidence suggests that walking and cycling for different purposes such as transport or recreation may be associated with different attributes of the physical environment. Few studies to date have examined these behaviour-specific associations, particularly in the UK. This paper reports on the development, factor structure and test-retest reliability of a new scale assessing perceptions of the environment in the neighbourhood (PENS) and the associations between perceptions of the environment and walking and cycling for transport and recreation. Methods A new 13-item scale was developed for assessing adults’ perceptions of the environment in the neighbourhood (PENS). Three sets of analyses were conducted using data from two sources. Exploratory and confirmatory factor analyses were used to identify a set of summary environmental variables using data from the iConnect baseline survey (n = 3494); test-retest reliability of the individual and summary environmental items was established using data collected in a separate reliability study (n = 166); and multivariable logistic regression was used to determine the associations of the environmental variables with walking for transport, walking for recreation, cycling for transport and cycling for recreation, using iConnect baseline survey data (n = 2937). Results Four summary environmental variables (traffic safety, supportive infrastructure, availability of local amenities and social order), one individual environmental item (street connectivity) and a variable encapsulating general environment quality were identified for use in further analyses. Intraclass correlations of these environmental variables ranged from 0.44 to 0.77 and were comparable to those seen in other similar scales. After adjustment for demographic and other environmental factors, walking for transport was associated with supportive infrastructure, availability of local amenities and general environment quality; walking for recreation was associated with supportive infrastructure; and cycling for transport was associated only with street connectivity. There was limited evidence of any associations between environmental attributes and cycling for recreation. Conclusion PENS is acceptable as a short instrument for assessing perceptions of the urban environment. Previous findings that different attributes of the environment may be associated with different behaviours are confirmed. Policy action to create supportive environments may require a combination of environmental improvements to promote walking and cycling for different purposes. PMID:23815872

Preliminary assessment of a potassium-steam-gas vapor cycle for better fuel economy and reduced thermal pollution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fraas, A.P.

1971-08-01

The facts of fuel supply limitations, environmental quality demands, and spiraling electric generating costs strongly favor development of electric power plants that simultaneously run at higher efficiency, i.e., higher temperature, use to advantage clean fuels, and have as low a capital cost as possible. Both fuel supply and thermal pollution considerations that are becoming progressively more important strongly favor the development of a higher temperature, and more efficient, thermodynamic cycle for electric power plants. About 200,000 hr of operation of boiling potassium systems, including over 15,000 hr of potassium vapor turbine operation under the space power plant program, suggest thatmore » a potassium vapor topping cycle with a turbine inlet temperature of approximately 1500/sup 0/F merits consideration. A design study has been carried out to indicate the size, cost, and development problems of the new types of equipment required. The results indicate that a potassium vapor cycle superimposed on a conventional 1050/sup 0/F steam cycle would give an overall thermal efficiency of about 54% as compared to only 40% from a conventional steam cycle. Thus the proposed system would have a fuel consumption only 75% and a heat rejection rate only 50% that of a conventional plant. The system requires clean fuel, and takes advantage of the present trend toward eliminating SO/sub 2/, NO/sub x/ and ash emissions. Surprisingly, at first sight, the assessment at this stage shows that the capital cost may be less than that of a conventional plant. The main reason for this is use of pressurized combustion, which leads to a much smaller combustor, and thin tube walls to contain potassium at about the same pressure.« less

Chasing Perfection: Should We Reduce Model Uncertainty in Carbon Cycle-Climate Feedbacks

NASA Astrophysics Data System (ADS)

Bonan, G. B.; Lombardozzi, D.; Wieder, W. R.; Lindsay, K. T.; Thomas, R. Q.

2015-12-01

Earth system model simulations of the terrestrial carbon (C) cycle show large multi-model spread in the carbon-concentration and carbon-climate feedback parameters. Large differences among models are also seen in their simulation of global vegetation and soil C stocks and other aspects of the C cycle, prompting concern about model uncertainty and our ability to faithfully represent fundamental aspects of the terrestrial C cycle in Earth system models. Benchmarking analyses that compare model simulations with common datasets have been proposed as a means to assess model fidelity with observations, and various model-data fusion techniques have been used to reduce model biases. While such efforts will reduce multi-model spread, they may not help reduce uncertainty (and increase confidence) in projections of the C cycle over the twenty-first century. Many ecological and biogeochemical processes represented in Earth system models are poorly understood at both the site scale and across large regions, where biotic and edaphic heterogeneity are important. Our experience with the Community Land Model (CLM) suggests that large uncertainty in the terrestrial C cycle and its feedback with climate change is an inherent property of biological systems. The challenge of representing life in Earth system models, with the rich diversity of lifeforms and complexity of biological systems, may necessitate a multitude of modeling approaches to capture the range of possible outcomes. Such models should encompass a range of plausible model structures. We distinguish between model parameter uncertainty and model structural uncertainty. Focusing on improved parameter estimates may, in fact, limit progress in assessing model structural uncertainty associated with realistically representing biological processes. Moreover, higher confidence may be achieved through better process representation, but this does not necessarily reduce uncertainty.

The role of circulating sex hormones in menstrual cycle dependent modulation of pain-related brain activation

PubMed Central

Veldhuijzen, Dieuwke S.; Keaser, Michael L.; Traub, Deborah S.; Zhuo, Jiachen; Gullapalli, Rao P.; Greenspan, Joel D.

2013-01-01

Sex differences in pain sensitivity have been consistently found but the basis for these differences is incompletely understood. The present study assessed how pain-related neural processing varies across the menstrual cycle in normally cycling, healthy females, and whether menstrual cycle effects are based on fluctuating sex hormone levels. Fifteen subjects participated in four test sessions during their menstrual, mid-follicular, ovulatory, and midluteal phases. Brain activity was measured while nonpainful and painful stimuli were applied with a pressure algometer. Serum hormone levels confirmed that scans were performed at appropriate cycle phases in 14 subjects. No significant cycle phase differences were found for pain intensity or unpleasantness ratings of stimuli applied during fMRI scans. However, lower pressure pain thresholds were found for follicular compared to other phases. Pain-specific brain activation was found in several regions traditionally associated with pain processing, including the medial thalamus, anterior and mid-insula, mid-cingulate, primary and secondary somatosensory cortices, cerebellum, and frontal regions. The inferior parietal lobule, occipital gyrus, cerebellum and several frontal regions demonstrated interaction effects between stimulus level and cycle phase, indicating differential processing of pain-related responses across menstrual cycle phases. Correlational analyses indicated that cycle-related changes in pain sensitivity measures and brain activation were only partly explained by varying sex hormone levels. These results show that pain-related cerebral activation varies significantly across the menstrual cycle, even when perceived pain intensity and unpleasantness remain constant. The involved brain regions suggest that cognitive pain or more general bodily awareness systems are most susceptible to menstrual cycle effects. PMID:23528204

Identifying built environmental patterns using cluster analysis and GIS: Relationships with walking, cycling and body mass index in French adults

PubMed Central

2012-01-01

Background Socio-ecological models suggest that both individual and neighborhood characteristics contribute to facilitating health-enhancing behaviors such as physical activity. Few European studies have explored relationships between local built environmental characteristics, recreational walking and cycling and weight status in adults. The aim of this study was to identify built environmental patterns in a French urban context and to assess associations with recreational walking and cycling behaviors as performed by middle-aged adult residents. Methods We used a two-step procedure based on cluster analysis to identify built environmental patterns in the region surrounding Paris, France, using measures derived from Geographic Information Systems databases on green spaces, proximity facilities (destinations) and cycle paths. Individual data were obtained from participants in the SU.VI.MAX cohort; 1,309 participants residing in the Ile-de-France in 2007 were included in this analysis. Associations between built environment patterns, leisure walking/cycling data (h/week) and measured weight status were assessed using multinomial logistic regression with adjustment for individual and neighborhood characteristics. Results Based on accessibility to green spaces, proximity facilities and availability of cycle paths, seven built environmental patterns were identified. The geographic distribution of built environmental patterns in the Ile-de-France showed that a pattern characterized by poor spatial accessibility to green spaces and proximity facilities and an absence of cycle paths was found only in neighborhoods in the outer suburbs, whereas patterns characterized by better spatial accessibility to green spaces, proximity facilities and cycle paths were more evenly distributed across the region. Compared to the reference pattern (poor accessibility to green areas and facilities, absence of cycle paths), subjects residing in neighborhoods characterized by high accessibility to green areas and local facilities and by a high density of cycle paths were more likely to walk/cycle, after adjustment for individual and neighborhood sociodemographic characteristics (OR = 2.5 95%CI 1.4-4.6). Body mass index did not differ across patterns. Conclusions Built environmental patterns were associated with walking and cycling among French adults. These analyses may be useful in determining urban and public health policies aimed at promoting a healthy lifestyle. PMID:22620266

Different postconditioning cycles affect prognosis of aged patients undergoing primary percutaneous coronary intervention.

PubMed

Zhang, Jie; Zhang, Xin; Cui, Yuqi; Ferdous, Misbahul; Cui, Lianqun; Zhao, Peng

2017-07-17

Postconditioning can affect the infarct size in acute myocardial infarction (AMI). However, few studies show an effect of different postconditioning cycles on AMI aged patients. This study sought to assess the effect of different postconditioning cycles on prognosis in aged patients with AMI who underwent primary percutaneous coronary intervention (PCI). 74 aged patients were randomly assigned to three groups. Control group; PC-1 group accepted postconditioning 4 cycles of 30 s inflation and 30 s deflation; PC-2 group accepted postconditioning 4 cycles of 60 s. Creatine kinase MB (CK-MB), troponin I (cTnI), high-sensitive C-reactive protein (hs-CRP) and corrected Thrombolysis in Myocardial Infarction (TIMI) frame counts (CTFC) were analyzed before andafter treatment. All patients received an echocardiographic examination for whole heart function, wall motion score index (WMSI) and single-photon emission computed tomography (SPECT) examination at 7 days and 6 months after treatment. S: The peak of CK-MB, postoperative 72 h cTnI and CTFC were significantly attenuated by postconditioning when compared with the control group. The hs-CRP of the postconditioning group was lower than the control group 24 h postoperative. No difference was observed between PC-1 and PC-2 group about the effect described above. At 7 days, heart function in the postconditioning group was improved when compared with the control group. At 6 months, the WMSI and SPECT score significantly reduced in the PC-2 group compared with the control and PC-1 groups, but there was no difference among the three groups about echo data except the left ventricular end-systolic diameter. Postconditioning is significantly beneficial to prognosis in aged patients with AMI. The cardiac protective effect of 4 cycles of 60 s procedure was observed in WMSI and SPECT. It is favorable to implement this procedure in aged patients with AMI in clinic.

LIFE CYCLE DESIGN OF AMORPHOUS SILICON PHOTOVOLTAIC MODULES

EPA Science Inventory

The life cycle design framework was applied to photovoltaic module design. The primary objective of this project was to develop and evaluate design metrics for assessing and guiding the Improvement of PV product systems. Two metrics were used to assess life cycle energy perform...

PRODUCT LIFE-CYCLE ASSESSMENT: INVENTORY GUIDELINES AND PRINCIPLES

EPA Science Inventory

The Life Cycle Assessment (LCA) can be used as an objective technical tool to evaluate the environmental consequences of a product, process, or activity holistically, across its entire life cycle. omplete LCA can be viewed as consisting of three complementary components (1) the i...

Assisted reproductive technology with donor sperm: national trends and perinatal outcomes.

PubMed

Gerkowicz, Sabrina A; Crawford, Sara B; Hipp, Heather S; Boulet, Sheree L; Kissin, Dmitry M; Kawwass, Jennifer F

2018-04-01

Information regarding the use of donor sperm in assisted reproductive technology, as well as subsequent treatment and perinatal outcomes, remains limited. Outcome data would aid patient counseling and clinical decision making. The objectives of the study were to report national trends in donor sperm utilization and live birth rates of donor sperm-assisted reproductive technology cycles in the United States and to compare assisted reproductive technology treatment and perinatal outcomes between cycles using donor and nondonor sperm. We hypothesize these outcomes to be comparable between donor and nondonor sperm cycles. This was a retrospective cohort study using data from all US fertility centers reporting to the Centers for Disease Control and Prevention's National Assisted Reproductive Technology Surveillance System, accounting for ∼98% of assisted reproductive technology cycles (definition excludes intrauterine insemination). The number and percentage of assisted reproductive technology cycles using donor sperm and rates of pregnancy, live birth, preterm birth (<37 weeks), and low birthweight (<2500 g) were the primary outcomes measured. Treatments assessed include use of donor vs nondonor sperm. The trends analysis included all banking and fresh assisted reproductive technology cycles using donor and autologous oocytes performed between 1996 and 2014 (n = 1,710,034). The outcomes analysis was restricted to include only fresh autologous cycles performed between 2010 and 2014 (n = 437,569) to focus on cycles with a potential outcome and cycles reflective of current practice, thereby improving the clinical relevance. Cycles canceled prior to retrieval were excluded. Statistical analysis included linear regression to explore polynomial trends and log-binomial regression to estimate relative risk for outcomes among cycles using donor and nondonor sperm. Of all banking and fresh donor and autologous oocyte assisted reproductive technology cycles performed between 1996 and 2014, 74,892 (4.4%) used donor sperm. In 2014, 7351 assisted reproductive technology cycles using donor sperm were performed, as compared with 1763 in 1996 (6.2% vs 3.8% of all cycles). Among all autologous oocyte cycles performed between 2010 and 2014, the live birth rate was lower for donor sperm (27.9%) than nondonor sperm cycles (32.5%); however, after adjustment for maternal age, donor sperm use was associated with an increased likelihood of live birth (adjusted relative risk, 1.06, 95% confidence interval, 1.01-1.10). Per transfer, there was no significant difference in live birth rates for donor vs nondonor sperm (31.9% vs 36.8%; adjusted relative risk, 1.04, 95% confidence interval, 0.998-1.09). Per singleton live birth, there was no significant difference in preterm birth (11.5% vs 11.8%; adjusted relative risk, 0.98, 95% confidence interval, 0.90-1.06); however, low birthweight delivery was slightly lower in donor sperm cycles (8.8% vs 9.4%; adjusted relative risk, 0.91, 95% confidence interval, 0.83-0.99). Donor sperm use in assisted reproductive technology has increased in the United States, accounting for approximately 6% of all assisted reproductive technology cycles in 2014. Assisted reproductive technology treatment and perinatal outcomes were clinically similar in donor and nondonor sperm cycles. Copyright © 2018 Elsevier Inc. All rights reserved.

Life cycle and economic assessment of source-separated MSW collection with regard to greenhouse gas emissions: a case study in China.

PubMed

Dong, Jun; Ni, Mingjiang; Chi, Yong; Zou, Daoan; Fu, Chao

2013-08-01

In China, the continuously increasing amount of municipal solid waste (MSW) has resulted in an urgent need for changing the current municipal solid waste management (MSWM) system based on mixed collection. A pilot program focusing on source-separated MSW collection was thus launched (2010) in Hangzhou, China, to lessen the related environmental loads. And greenhouse gas (GHG) emissions (Kyoto Protocol) are singled out in particular. This paper uses life cycle assessment modeling to evaluate the potential environmental improvement with regard to GHG emissions. The pre-existing MSWM system is assessed as baseline, while the source separation scenario is compared internally. Results show that 23 % GHG emissions can be decreased by source-separated collection compared with the base scenario. In addition, the use of composting and anaerobic digestion (AD) is suggested for further optimizing the management of food waste. 260.79, 82.21, and -86.21 thousand tonnes of GHG emissions are emitted from food waste landfill, composting, and AD, respectively, proving the emission reduction potential brought by advanced food waste treatment technologies. Realizing the fact, a modified MSWM system is proposed by taking AD as food waste substitution option, with additional 44 % GHG emissions saved than current source separation scenario. Moreover, a preliminary economic assessment is implemented. It is demonstrated that both source separation scenarios have a good cost reduction potential than mixed collection, with the proposed new system the most cost-effective one.

A comparison of bleeding patterns and cycle control using two transdermal contraceptive systems: a multicenter, open-label, randomized study.

PubMed

Gruber, D; Skřivánek, A; Serrani, M; Lanius, V; Merz, M

2015-02-01

To investigate the bleeding pattern and cycle control parameters of a contraceptive patch containing 0.55 mg ethinyl estradiol (EE) and 2.1 mg gestodene (GSD) compared with a patch containing 0.6 mg EE and 6 mg norelgestromin (NGMN). In this phase III, open-label, randomized, parallel-group trial, healthy women aged 18-35 years (smokers aged 18-30 years) received either the EE/GSD patch (n=200) or the EE/NGMN patch (n=198). Treatment consisted of one patch per week for 3 weeks followed by a 7-day, patch-free interval for seven cycles. Bleeding control was assessed in two 90-day reference periods. In reference period 1, mean number of bleeding/spotting days was comparable across treatment groups (p>0.05). However, in reference period 2, there were fewer bleeding/spotting days in the EE/GSD patch group (15.7 versus 18.4; p<0.0001). Mean number of bleeding/spotting episodes was comparable across groups for both reference periods, but bleeding/spotting episodes were shorter for the EE/GSD patch than the EE/NGMN patch during reference period 1 (5.13 days versus 5.53 days, respectively; p<0.05) and reference period 2 (5.07 versus 5.66; p=0.0001). Both treatment groups showed a similar frequency of withdrawal bleeding episodes; however, across all seven cycles, the length of these episodes was consistently shorter with the EE/GSD patch (p<0.01). There were no notable treatment differences in intracyclic bleeding. Bleeding pattern and cycle control achieved with the EE/GSD patch was similar to that of the EE/NGMN patch. The paper presents data on the bleeding pattern and cycle control parameters of an investigational transdermal contraceptive patch containing EE and GSD compared with an approved contraceptive patch containing EE and NGMN. This descriptive study found that bleeding patterns associated with the EE/GSD patch were similar to those of an EE/NGMN patch providing higher EE exposure. Copyright © 2015 Elsevier Inc. All rights reserved.

Tribological assessment of a flexible carbon-fibre-reinforced poly(ether-ether-ketone) acetabular cup articulating against an alumina femoral head.

PubMed

Scholes, S C; Inman, I A; Unsworth, A; Jones, E

2008-04-01

New material combinations have been introduced as the bearing surfaces of hip prostheses in an attempt to prolong their life by overcoming the problems of failure due to wear-particle-induced osteolysis. This will hopefully reduce the need for revision surgery. The study detailed here used a hip simulator to assess the volumetric wear rates of large-diameter carbon-fibre-reinforced pitch-based poly(ether-ether-ketone) (CFR-PEEK) acetabular cups articulating against alumina femoral heads. The joints were tested for 25 x 10(6) cycles. Friction tests were also performed on these joints to determine the lubrication regime under which they operate. The average volumetric wear rate of the CFR-PEEK acetabular component of 54 mm diameter was 1.16 mm(3)/10(6) cycles, compared with 38.6 mm(3)/10(6) cycles for an ultra-high-molecular-weight polyethylene acetabular component of 28 mm diameter worn against a ceramic head. This extremely low wear rate was sustained over 25 x 10(6) cycles (the equivalent of up to approximately 25 years in vivo). The frictional studies showed that the joints worked under the mixed-boundary lubrication regime. The low wear produced by these joints showed that this novel joint couple offers low wear rates and therefore may be an alternative material choice for the reduction of osteolysis.

Life cycle assessment of a power tower concentrating solar plant and the impacts of key design alternatives.

PubMed

Whitaker, Michael B; Heath, Garvin A; Burkhardt, John J; Turchi, Craig S

2013-06-04

A hybrid life cycle assessment (LCA) is used to evaluate four sustainability metrics over the life cycle of a power tower concentrating solar power (CSP) facility: greenhouse gas (GHG) emissions, water consumption, cumulative energy demand (CED), and energy payback time (EPBT). The reference design is for a dry-cooled, 106 MW(net) power tower facility located near Tucson, AZ that uses a mixture of mined nitrate salts as the heat transfer fluid and storage medium, a two-tank thermal energy storage system designed for six hours of full load-equivalent storage, and receives auxiliary power from the local electric grid. A thermocline-based storage system, synthetically derived salts, and natural gas auxiliary power are evaluated as design alternatives. Over its life cycle, the reference plant is estimated to have GHG emissions of 37 g CO2eq/kWh, consume 1.4 L/kWh of water and 0.49 MJ/kWh of energy, and have an EPBT of 15 months. Using synthetic salts is estimated to increase GHG emissions by 12%, CED by 7%, and water consumption by 4% compared to mined salts. Natural gas auxiliary power results in greater than 10% decreases in GHG emissions, water consumption, and CED. The thermocline design is most advantageous when coupled with the use of synthetic salts.

The Effects of ISM1 Medium on Embryo Quality and Outcomes of IVF/ICSI Cycles.

PubMed

Hassani, Fatemeh; Eftekhari-Yazdi, Poopak; Karimian, Leila; Rezazadeh Valojerdi, Mojtaba; Movaghar, Bahar; Fazel, Mohammad; Fouladi, Hamid Reza; Shabani, Fatemeh; Johansson, Lars

2013-07-01

The aim of this study is to investigate the effect of ISM1 culture medium on embryo development, quality and outcomes of in vitro fertilization/intracytoplasmic sperm injection (IVF/ICSI) cycles. This study compares culture medium commonly used in the laboratory setting for oocyte recovery and embryo development with a medium from MediCult. We have assessed the effects of these media on embryo development and newborn characteristics. In this prospective randomized study, fertilized oocytes from patients were randomly assigned to culture in ISM1 (MediCult, cycles: n=293) or routine lab culture medium (G-1TM v5; Vitrolife, cycles: n=290) according to the daily media schedule for oocyte retrieval. IVF or ICSI and embryo transfer were performed with either MediCult media or routine lab media. Embryo quality on days 2/3, cleavage, pregnancy and implantation rates, baby take home rate (BTHR), in addition to the weight and length of newborns were compared between groups. There were similar cleavage rates for ISM1 (86%) vs. G-1TM v5 (88%). We observed a significantly higher percentage of excellent embryos in ISM1 (42.7%) compared to G-1TM v5 (39%, p<0.05). Babies born after culture in ISM1 had both higher birth weight (3.03 kg) and length (48.8 cm) compared to G-1TM v5 babies that had a birth weight of 2.66 kg and a length of 46.0 cm (p<0.001 for both). This study suggests that ISM1 is a more effective culture medium in generating higher quality embryos, which may be reflected in the characteristics of babies at birth.

The Effects of ISM1 Medium on Embryo Quality and Outcomes of IVF/ICSI Cycles

PubMed Central

Hassani, Fatemeh; Eftekhari-Yazdi, Poopak; Karimian, Leila; Rezazadeh Valojerdi, Mojtaba; Movaghar, Bahar; Fazel, Mohammad; Fouladi, Hamid Reza; Shabani, Fatemeh; Johansson, Lars

2013-01-01

Background: The aim of this study is to investigate the effect of ISM1 culture medium on embryo development, quality and outcomes of in vitro fertilization/intracytoplasmic sperm injection (IVF/ICSI) cycles. This study compares culture medium commonly used in the laboratory setting for oocyte recovery and embryo development with a medium from MediCult. We have assessed the effects of these media on embryo development and newborn characteristics. Materials and Methods: In this prospective randomized study, fertilized oocytes from patients were randomly assigned to culture in ISM1 (MediCult, cycles: n=293) or routine lab culture medium (G-1TM v5; Vitrolife, cycles: n=290) according to the daily media schedule for oocyte retrieval. IVF or ICSI and embryo transfer were performed with either MediCult media or routine lab media. Embryo quality on days 2/3, cleavage, pregnancy and implantation rates, baby take home rate (BTHR), in addition to the weight and length of newborns were compared between groups. Results: There were similar cleavage rates for ISM1 (86%) vs. G-1TM v5 (88%). We observed a significantly higher percentage of excellent embryos in ISM1 (42.7%) compared to G-1TM v5 (39%, p<0.05). Babies born after culture in ISM1 had both higher birth weight (3.03 kg) and length (48.8 cm) compared to G-1TM v5 babies that had a birth weight of 2.66 kg and a length of 46.0 cm (p<0.001 for both). Conclusion: This study suggests that ISM1 is a more effective culture medium in generating higher quality embryos, which may be reflected in the characteristics of babies at birth. PMID:24520472

LIFE CYCLE IMPACT ASSESSMENT AN INTRODUCTION AND INTERNATIONAL UPDATE

EPA Science Inventory

Research within the field of Life Cycle Impact Assessment (LCIA) has greatly improved since the work of Heijungs and Guinee in 1992. Within the UNEP / SETAC Life Cycle Initiative an effort is underway to provide recommendations about the direction of research and selection of LC...

Dealing with Emergy Algebra in the Life Cycle Assessment Framework

EPA Science Inventory

The Life Cycle Inventory (LCI) represents one of the four steps of the Life Cycle Assessment (LCA) methodology, which is a standardized procedure (ISO 14040:2006) to estimate the environmental impacts generated by the production, use and disposal of goods and services. In this co...

Comparison of energy-based indicators used in life cycle assessment tools for buildings

EPA Science Inventory

Traditionally, building rating systems focused on, among others, energy used during operational stage. Recently, there is a strong push by these rating systems to include the life cycle energy use of buildings, particularly using Life Cycle Assessment (LCA), by offering credits t...

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE BGU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyrotechnic (PEP) materials of interest to the U.S. Department of Defense (DoD)...

Integrated Metrics for Improving the Life Cycle Approach to Assessing Product System Sustainability

EPA Science Inventory

Life cycle approaches are critical for identifying and managing to reduce burdens in the sustainability of product systems. While these methods can indicate potential environmental impacts of a product, current Life Cycle Assessment (LCA) methods fail to integrate the multiple im...

Real-world experience of women using extended-cycle vs monthly-cycle combined oral contraception in the United States: the National Health and Wellness Survey.

PubMed

Nappi, Rossella E; Lete, Iñaki; Lee, Lulu K; Flores, Natalia M; Micheletti, Marie-Christine; Tang, Boxiong

2018-01-18

The real-world experience of women receiving extended-cycle combined oral contraception (COC) versus monthly-cycle COC has not been reported. Data were from the United States 2013 National Health and Wellness Survey. Eligible women (18-50 years old, premenopausal, without hysterectomy) currently using extended-cycle COC (3 months between periods) were compared with women using monthly-cycle COC. Treatment satisfaction (1 "extremely dissatisfied" to 7 "extremely satisfied"), adherence (8-item Morisky Medication Adherence Scale © ), menstrual cycle-related symptoms, health-related quality of life (HRQOL) and health state utilities (Medical Outcomes Short Form Survey-36v2®), depression (9-item Patient Health Questionnaire), sleep difficulties, Work Productivity and Activity Impairment-General Health, and healthcare resource use were assessed using one-way analyses of variance, chi-square tests, and generalized linear models (adjusted for covariates). Participants included 260 (6.7%) women using extended-cycle and 3616 (93.3%) using monthly-cycle COC. Women using extended-cycle COC reported significantly higher treatment satisfaction (P = 0.001) and adherence (P = 0.04) and reduced heavy menstrual bleeding (P = 0.029). A non-significant tendency toward reduced menstrual pain (39.5% versus 47.3%) and menstrual cycle-related symptoms (40.0% versus 48.7%) was found in women using extended-cycle versus monthly-cycle COC. Significantly more women using extended-cycle COC reported health-related diagnoses, indicating preferential prescription for extended-cycle COC among women reporting more health problems. Consistent with this poorer health, more women using extended-cycle COC reported fatigue, headache, and activity impairment (P values < 0.05). There were no other significant differences between groups. This real-world observational study supports extended-cycle COC as a valuable treatment option with high satisfaction, high adherence, and reduced heavy menstrual bleeding.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuenge, Jason R.; Hollomon, Brad; Dillon, Heather E.

This report covers the third part of a larger U.S. Department of Energy (DOE) project to assess the life-cycle environmental and resource impacts in the manufacturing, transport, use, and disposal of light-emitting diode (LED) lighting products in relation to incumbent lighting technologies. All three reports are available on the DOE website (www.ssl.energy.gov/tech_reports.html). • Part 1: Review of the Life-Cycle Energy Consumption of Incandescent, Compact Fluorescent and LED Lamps; • Part 2: LED Manufacturing and Performance; • Part 3: LED Environmental Testing. Parts 1 and 2 were published in February and June 2012, respectively. The Part 1 report included a summarymore » of the life-cycle assessment (LCA) process and methodology, provided a literature review of more than 25 existing LCA studies of various lamp types, and performed a meta-analysis comparing LED lamps with incandescent and compact fluorescent lamps (CFLs). Drawing from the Part 1 findings, Part 2 performed a more detailed assessment of the LED manufacturing process and used these findings to provide a comparative LCA taking into consideration a wider range of environmental impacts. Both reports concluded that the life-cycle environmental impact of a given lamp is dominated by the energy used during lamp operation—the upstream generation of electricity drives the total environmental footprint of the product. However, a more detailed understanding of end-of-life disposal considerations for LED products has become increasingly important as their installation base has grown. The Part 3 study (reported herein) was undertaken to augment the LCA findings with chemical analysis of a variety of LED, CFL, and incandescent lamps using standard testing procedures. A total of 22 samples, representing 11 different models, were tested to determine whether any of 17 elements were present at levels exceeding California or Federal regulatory thresholds for hazardous waste. Key findings include: • The selected models were generally found to be below thresholds for Federally regulated elements; • All CFLs and LED lamps and most incandescent lamps exceeded California thresholds for Copper; • Most CFL samples exceeded California thresholds for Antimony and Nickel, and half of the LED samples exceeded California thresholds for Zinc; • The greatest contributors were the screw bases, drivers, ballasts, and wires or filaments; • Overall concentrations in LED lamps were comparable to cell phones and other types of electronic devices, and were generally attributable to components other than the internal LED light sources; • Although the life-cycle environmental impact of the LED lamps is favorable when compared to CFLs and incandescent lamps, recycling will likely gain importance as consumer adoption increases. This study was exploratory in nature and was not intended to provide a definitive indication of regulatory compliance for any specific lamp model or technology. Further study would be needed to more broadly characterize the various light source technologies; to more accurately and precisely characterize a specific model; or to determine whether product redesign would be appropriate.« less

Ore grade decrease as life cycle impact indicator for metal scarcity: the case of copper.

PubMed

Vieira, Marisa D M; Goedkoop, Mark J; Storm, Per; Huijbregts, Mark A J

2012-12-04

In the life cycle assessment (LCA) of products, the increasing scarcity of metal resources is currently addressed in a preliminary way. Here, we propose a new method on the basis of global ore grade information to assess the importance of the extraction of metal resources in the life cycle of products. It is shown how characterization factors, reflecting the decrease in ore grade due to an increase in metal extraction, can be derived from cumulative ore grade-tonnage relationships. CFs were derived for three different types of copper deposits (porphyry, sediment-hosted, and volcanogenic massive sulfide). We tested the influence of the CF model (marginal vs average), mathematical distribution (loglogistic vs loglinear), and reserve estimate (ultimate reserve vs reserve base). For the marginal CFs, the statistical distribution choice and the estimate of the copper reserves introduce a difference of a factor of 1.0-5.0 and a factor of 1.2-1.7, respectively. For the average CFs, the differences are larger for these two choices, i.e. respectively a factor of 5.7-43 and a factor of 2.1-3.8. Comparing the marginal CFs with the average CFs, the differences are higher (a factor 1.7-94). This paper demonstrates that cumulative grade-tonnage relationships for metal extraction can be used in LCA to assess the relative importance of metal extractions.

Cumulative exergy extraction from the natural environment (CEENE): a comprehensive life cycle impact assessment method for resource accounting.

PubMed

Dewulf, J; Bösch, M E; De Meester, B; Van der Vorst, G; Van Langenhove, H; Hellweg, S; Huijbregts, M A J

2007-12-15

The objective of the paper is to establish a comprehensive resource-based life cycle impact assessment (LCIA) method which is scientifically sound and that enables to assess all kinds of resources that are deprived from the natural ecosystem, all quantified on one single scale, free of weighting factors. The method is based on the exergy concept. Consistent exergy data on fossils, nuclear and metal ores, minerals, air, water, land occupation, and renewable energy sources were elaborated, with well defined system boundaries. Based on these data, the method quantifies the exergy "taken away" from natural ecosystems, and is thus called the cumulative exergy extraction from the natural environment (CEENE). The acquired data set was coupled with a state-of-the art life cycle inventory database, ecoinvent. In this way, the method is able to quantitatively distinguish eight categories of resources withdrawn from the natural environment: renewable resources, fossil fuels, nuclear energy, metal ores, minerals, water resources, land resources, and atmospheric resources. Third, the CEENE method is illustrated for a number of products that are available in ecoinvent, and results are compared with common resource oriented LCIA methods. The application to the materials in the ecoinvent database showed that fossil resources and land use are of particular importance with regard to the total CEENE score, although the other resource categories may also be significant.

RISK ASSESSMENT AND LIFE CYCLE IMPACT ASSESSMENT (LCIA) FOR HUMAN HEALTH CANCEROUS AND NONCANCEROUS EMISSIONS: INTEGRATED AND COMPLEMENTARY WITH CONSISTENCY WITHIN THE USEPA

EPA Science Inventory

The historical parallels, complementary roles, and potential for integration of human health risk assessment (RA) and Life-Cycle Impact Assessment (LCIA) are explored. Previous authors have considered the comparison of LCA and risk assessment recognizing the inherent differences ...

Life cycle assessment of domestic and agricultural rainwater harvesting systems.

PubMed

Ghimire, Santosh R; Johnston, John M; Ingwersen, Wesley W; Hawkins, Troy R

2014-04-01

To further understanding of the environmental implications of rainwater harvesting and its water savings potential relative to conventional U.S. water delivery infrastructure, we present a method to perform life cycle assessment of domestic rainwater harvesting (DRWH) and agricultural rainwater harvesting (ARWH) systems. We also summarize the design aspects of DRWH and ARWH systems adapted to the Back Creek watershed, Virginia. The baseline design reveals that the pump and pumping electricity are the main components of DRWH and ARWH impacts. For nonpotable uses, the minimal design of DRWH (with shortened distribution distance and no pump) outperforms municipal drinking water in all environmental impact categories except ecotoxicity. The minimal design of ARWH outperforms well water in all impact categories. In terms of watershed sustainability, the two minimal designs reduced environmental impacts, from 58% to 78% energy use and 67% to 88% human health criteria pollutants, as well as avoiding up to 20% blue water (surface/groundwater) losses, compared to municipal drinking water and well water. We address potential environmental and human health impacts of urban and rural RWH systems in the region. The Building for Environmental and Economic Sustainability (BEES) model-based life cycle inventory data were used for this study.

An evidential reasoning-based AHP approach for the selection of environmentally-friendly designs

DOE Office of Scientific and Technical Information (OSTI.GOV)

NG, C.Y., E-mail: ng.cy@cityu.edu.hk

Due to the stringent environmental regulatory requirements being imposed by cross-national bodies in recent years, manufacturers have to minimize the environmental impact of their products. Among those environmental impact evaluation tools available, Life Cycle Assessment (LCA) is often employed to quantify the product's environmental impact throughout its entire life cycle. However, owing to the requirements of expert knowledge in environmental science and vast effort for data collection in carrying out LCA, as well as the common absence of complete product information during product development processes, there is a need to develop a more suitable tool for product designers. An evidentialmore » reasoning-based approach, which aims at providing a fast-track method to perform design alternative evaluations for non-LCA experts, is therefore introduced as a new initiative to deal with the incomplete or uncertain information. The proposed approach also enables decision makers to quantitatively assess the life cycle phases and design alternatives by comparing their potential environmental impacts, thus effectively and efficiently facilitates the identification of greener designs. A case application is carried out to demonstrate the applicability of the proposed approach.« less

Trophic Ecology of Benthic Marine Invertebrates with Bi-Phasic Life Cycles: What Are We Still Missing?

PubMed

Calado, Ricardo; Leal, Miguel Costa

2015-01-01

The study of trophic ecology of benthic marine invertebrates with bi-phasic life cycles is critical to understand the mechanisms shaping population dynamics. Moreover, global climate change is impacting the marine environment at an unprecedented level, which promotes trophic mismatches that affect the phenology of these species and, ultimately, act as drivers of ecological and evolutionary change. Assessing the trophic ecology of marine invertebrates is critical to understanding maternal investment, larval survival to metamorphosis, post-metamorphic performance, resource partitioning and trophic cascades. Tools already available to assess the trophic ecology of marine invertebrates, including visual observation, gut content analysis, food concentration, trophic markers, stable isotopes and molecular genetics, are reviewed and their main advantages and disadvantages for qualitative and quantitative approaches are discussed. The challenges to perform the partitioning of ingestion, digestion and assimilation are discussed together with different approaches to address each of these processes for short- and long-term fingerprinting. Future directions for research on the trophic ecology of benthic marine invertebrates with bi-phasic life cycles are discussed with emphasis on five guidelines that will allow for systematic study and comparative meta-analysis to address important unresolved questions. © 2015 Elsevier Ltd. All rights reserved.

Prospective environmental life cycle assessment of nanosilver T-shirts.

PubMed

Walser, Tobias; Demou, Evangelia; Lang, Daniel J; Hellweg, Stefanie

2011-05-15

A cradle-to-grave life cycle assessment (LCA) is performed to compare nanosilver T-shirts with conventional T-shirts with and without biocidal treatment. For nanosilver production and textile incorporation, we investigate two processes: flame spray pyrolysis (FSP) and plasma polymerization with silver co-sputtering (PlaSpu). Prospective environmental impacts due to increased nanosilver T-shirt commercialization are estimated with six scenarios. Results show significant differences in environmental burdens between nanoparticle production technologies: The "cradle-to-gate" climate footprint of the production of a nanosilver T-shirt is 2.70 kg of CO(2)-equiv (FSP) and 7.67-166 kg of CO(2)-equiv (PlaSpu, varying maturity stages). Production of conventional T-shirts with and without the biocide triclosan has emissions of 2.55 kg of CO(2)-equiv (contribution from triclosan insignificant). Consumer behavior considerably affects the environmental impacts during the use phase. Lower washing frequencies can compensate for the increased climate footprint of FSP nanosilver T-shirt production. The toxic releases from washing and disposal in the life cycle of T-shirts appear to be of minor relevance. By contrast, the production phase may be rather significant due to toxic silver emissions at the mining site if high silver quantities are required.

Soil and foliar nutrient and nitrogen isotope composition (δ(15)N) at 5 years after poultry litter and green waste biochar amendment in a macadamia orchard.

PubMed

Bai, Shahla Hosseini; Xu, Cheng-Yuan; Xu, Zhihong; Blumfield, Timothy J; Zhao, Haitao; Wallace, Helen; Reverchon, Frédérique; Van Zwieten, Lukas

2015-03-01

This study aimed to evaluate the improvement in soil fertility and plant nutrient use in a macadamia orchard following biochar application. The main objectives of this study were to assess the effects of poultry litter and green waste biochar applications on nitrogen (N) cycling using N isotope composition (δ(15)N) and nutrient availability in a soil-plant system at a macadamia orchard, 5 years following application. Biochar was applied at 10 t ha(-1) dry weight but concentrated within a 3-m diameter zone when trees were planted in 2007. Soil and leaf samples were collected in 2012, and both soil and foliar N isotope composition (δ(15)N) and nutrient concentrations were assessed. Both soil and foliar δ(15)N increased significantly in the poultry litter biochar plots compared to the green waste biochar and control plots. A significant relationship was observed between soil and plant δ(15)N. There was no influence of either biochars on foliar total N concentrations or soil NH4 (+)-N and NO3 (-)-N, which suggested that biochar application did not pose any restriction for plant N uptake. Plant bioavailable phosphorus (P) was significantly higher in the poultry litter biochar treatment compared to the green waste biochar treatment and control. We hypothesised that the bioavailability of N and P content of poultry litter biochar may play an important role in increasing soil and plant δ(15)N and P concentrations. Biochar application affected soil-plant N cycling and there is potential to use soil and plant δ(15)N to investigate N cycling in a soil-biochar-tree crop system. The poultry litter biochar significantly increased soil fertility compared to the green waste biochar at 5 years following biochar application which makes the poultry litter a better feedstock to produce biochar compared to green waste for the tree crops.

Life cycle assessment of construction and demolition waste management.

PubMed

Butera, Stefania; Christensen, Thomas H; Astrup, Thomas F

2015-10-01

Life cycle assessment (LCA) modelling of construction and demolition waste (C&DW) management was carried out. The functional unit was management of 1 Mg mineral, source separated C&DW, which is either utilised in road construction as a substitute for natural aggregates, or landfilled. The assessed environmental impacts included both non-toxic and toxic impact categories. The scenarios comprised all stages of the end-of-life management of C&DW, until final disposal of all residues. Leaching of inorganic contaminants was included, as was the production of natural aggregates, which was avoided because of the use of C&DW. Typical uncertainties related to contaminant leaching were addressed. For most impact categories, utilisation of C&DW in road construction was preferable to landfilling; however, for most categories, utilisation resulted in net environmental burdens. Transportation represented the most important contribution for most nontoxic impacts, accounting for 60-95 per cent of these impacts. Capital goods contributed with negligible impacts. Leaching played a critical role for the toxic categories, where landfilling had lower impacts than utilisation because of the lower levels of leachate per ton of C&DW reaching the groundwater over a 100-year perspective. Leaching of oxyanions (As, V and Sb) was critical with respect to leaching. Typical experimental uncertainties in leaching data did not have a pivotal influence on the results; however, accounting for Cr immobilisation in soils as part of the impact assessment was critical for modelling the leaching impacts. Compared with the overall life cycle of building and construction materials, leaching emissions were shown to be potentially significant for toxicity impacts, compared with contributions from production of the same materials, showing that end-of-life impacts and leaching should not be disregarded when assessing environmental impacts from construction products and materials. CO2 uptake in the C&DW corresponding to 15 per cent carbonation could out-balance global warming impacts from transportation; however, carbonation would also likely result in increased toxicity impacts due to higher leaching of oxyanions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Water quality in New Zealand's planted forests: A review

Treesearch

Brenda R. Baillie; Daniel G. Neary

2015-01-01

This paper reviewed the key physical, chemical and biological water quality attributes of surface waters in New Zealand’s planted forests. The purpose was to: a) assess the changes in water quality throughout the planted forestry cycle from afforestation through to harvesting; b) compare water quality from planted forests with other land uses in New Zealand; and c)...

An Evaluation of Two Hands-On Lab Styles for Plant Biodiversity in Undergraduate Biology

ERIC Educational Resources Information Center

Basey, John M.; Maines, Anastasia P.; Francis, Clinton D.; Melbourne, Brett

2014-01-01

We compared learning cycle and expository formats for teaching about plant biodiversity in an inquiry-oriented university biology lab class (n = 465). Both formats had preparatory lab activities, a hands-on lab, and a postlab with reflection and argumentation. Learning was assessed with a lab report, a practical quiz in lab, and a multiple-choice…

Environmental consequences of future biogas technologies based on separated slurry.

PubMed

Hamelin, Lorie; Wesnæs, Marianne; Wenzel, Henrik; Petersen, Bjørn M

2011-07-01

This consequential life cycle assessment study highlights the key environmental aspects of producing biogas from separated pig and cow slurry, a relatively new but probable scenario for future biogas production, as it avoids the reliance on constrained carbon cosubstrates. Three scenarios involving different slurry separation technologies have been assessed and compared to a business-as-usual reference slurry management scenario. The results show that the environmental benefits of such biogas production are highly dependent upon the efficiency of the separation technology used to concentrate the volatile solids in the solid fraction. The biogas scenario involving the most efficient separation technology resulted in a dry matter separation efficiency of 87% and allowed a net reduction of the global warming potential of 40%, compared to the reference slurry management. This figure comprises the whole slurry life cycle, including the flows bypassing the biogas plant. This study includes soil carbon balances and a method for quantifying the changes in yield resulting from increased nitrogen availability as well as for quantifying mineral fertilizers displacement. Soil carbon balances showed that between 13 and 50% less carbon ends up in the soil pool with the different biogas alternatives, as opposed to the reference slurry management.

Environmental Impact of Buildings--What Matters?

PubMed

Heeren, Niko; Mutel, Christopher L; Steubing, Bernhard; Ostermeyer, York; Wallbaum, Holger; Hellweg, Stefanie

2015-08-18

The goal of this study was to identify drivers of environmental impact and quantify their influence on the environmental performance of wooden and massive residential and office buildings. We performed a life cycle assessment and used thermal simulation to quantify operational energy demand and to account for differences in thermal inertia of building mass. Twenty-eight input parameters, affecting operation, design, material, and exogenic building properties were sampled in a Monte Carlo analysis. To determine sensitivity, we calculated the correlation between each parameter and the resulting life cycle inventory and impact assessment scores. Parameters affecting operational energy demand and energy conversion are the most influential for the building's total environmental performance. For climate change, electricity mix, ventilation rate, heating system, and construction material rank the highest. Thermal inertia results in an average 2-6% difference in heat demand. Nonrenewable cumulative energy demand of wooden buildings is 18% lower, compared to a massive variant. Total cumulative energy demand is comparable. The median climate change impact is 25% lower, including end-of-life material credits and 22% lower, when credits are excluded. The findings are valid for small offices and residential buildings in Switzerland and regions with similar building culture, construction material production, and climate.

Characterization factors for thermal pollution in freshwater aquatic environments.

PubMed

Verones, Francesca; Hanafiah, Marlia Mohd; Pfister, Stephan; Huijbregts, Mark A J; Pelletier, Gregory J; Koehler, Annette

2010-12-15

To date the impact of thermal emissions has not been addressed in life cycle assessment despite the narrow thermal tolerance of most aquatic species. A method to derive characterization factors for the impact of cooling water discharges on aquatic ecosystems was developed which uses space and time explicit integration of fate and effects of water temperature changes. The fate factor is calculated with a 1-dimensional steady-state model and reflects the residence time of heat emissions in the river. The effect factor specifies the loss of species diversity per unit of temperature increase and is based on a species sensitivity distribution of temperature tolerance intervals for various aquatic species. As an example, time explicit characterization factors were calculated for the cooling water discharge of a nuclear power plant in Switzerland, quantifying the impact on aquatic ecosystems of the rivers Aare and Rhine. The relative importance of the impact of these cooling water discharges was compared with other impacts in life cycle assessment. We found that thermal emissions are relevant for aquatic ecosystems compared to other stressors, such as chemicals and nutrients. For the case of nuclear electricity investigated, thermal emissions contribute between 3% and over 90% to Ecosystem Quality damage.

Sustainability Analysis | Energy Analysis | NREL

Science.gov Websites

environmental, life-cycle, climate, and other impacts of renewable energy technologies. Photo of a man viewing a energy choices within the complex web of connections between energy and water. Life Cycle Assessment Harmonization Our life cycle assessment harmonization provides lenders, utility executives, and lawmakers with

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE GBU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyro-technic (PEP) materials of interest to the U.S. Department of Defense (DoD...

LCACCESS: A GLOBAL DIRECTORY OF LIFE CYCLE ASSESSMENT RESOURCES

EPA Science Inventory

LCAccess is an EPA-sponsored website intended to promote the use of Life Cycle Assessment (LCA) in business decision-making by faciliatating access to data sources that are useful in developing a life cycle inventory (LCI). While LCAccess does not itself contain data, it is a sea...

Towards a more sustainable transport infrastructure: how spatial geological data can be utilized to improve early stage Life cycle assessment of road infrastructure

NASA Astrophysics Data System (ADS)

Karlsson, Caroline; Miliutenko, Sofiia; Björklund, Anna; Mörtberg, Ulla; Olofsson, Bo; Toller, Susanna

2017-04-01

Environmental impacts during the life cycle stages of transport infrastructure are substantial, including among other greenhouse gas (GHG) emissions, as well as resource and energy use. For transport infrastructure to be sustainable, such issues need to be integrated in the planning process. Environmental Impact Assessment (EIA) is required by the European Union (EU) in order to ensure that all environmental aspects are considered during planning of road infrastructure projects. As a part of this process, the European Commission has suggested the use of the tool life cycle assessment (LCA) for assessing life cycle energy use and GHG emissions. When analyzing life cycle impacts of the road infrastructure itself, it was shown that earthworks and materials used for the road construction have a big share in the total energy use and GHG emissions. Those aspects are largely determined by the geological conditions at the site of construction: parameters such as soil thickness, slope, bedrock quality and soil type. The geological parameters determine the amounts of earthworks (i.e. volumes of soil and rock that will be excavated and blasted), transportation need for excavated materials as well as the availability of building materials. The study presents a new geographic information system (GIS)-based approach for utilizing spatial geological data in three dimensions (i.e. length, width and depth) in order to improve estimates on earthworks during the early stages of road infrastructure planning. Three main methodological steps were undertaken: mass balance calculation, life cycle inventory analysis and spatial mapping of greenhouse gas (GHG) emissions and energy use. The proposed GIS-based approach was later evaluated by comparing with the actual values of extracted material of a real road construction project. The results showed that the estimate of filling material was the most accurate, while the estimate for excavated soil and blasted rock had a wide variation from the actual values. It was also found that the total volume of excavated and ripped soils did not change when accounting for geological stratigraphy. The proposed GIS-based approach shows promising results for usage in LCA at an early stage of road infrastructure planning, and by providing better data quality, GIS in combination with LCA can enable planning for a more sustainable transport infrastructure.

The impact of different cross-training modalities on performance and injury-related variables in high school cross country runners.

PubMed

Paquette, Max R; Peel, Shelby A; Smith, Ross E; Temme, Mark; Dwyer, Jeffrey N

2017-11-29

There are many different types of aerobic cross-training modalities currently available. It is important to consider the effects that these different modalities have on running performance and injury risks. The purpose of this study was to compare movement quality, running economy and performance, injury-related biomechanical variables and, hip muscle strength before and after training with different cross-training modalities in high school runners. Thirty-one high school male runners trained for four weeks in one of three cross-training modalities, in addition to a running-only (RUN, n=9) group, for which training sessions replaced two easy runs per week: cycling (CYCLE; n=6), indoor elliptical (ELLIP; n=7) and, outdoor elliptical bike (EBIKE; n=9). Functional movement screen (FMS), running economy (RE), 3,000m performance, hip kinematics, hip muscle strength were assessed. Paired t-tests and Cohen's d effect sizes were used to assess mean differences for each variable before and after training within each group. EBIKE training was the only modality that improved FMS scores (d = 1.36) and RE before and after training (d = 0.48). All groups showed improvements in 3,000m performance but large effects were only found for the CYCLE (d = 1.50) and EBIKE (d = 1.41) groups. RUN (d = 1.25), CYCLE (d = 1.17) and, EBIKE (d = 0.82) groups showed improvements in maximal hip extensor strength. Outdoor cycling and elliptical bike cross-training may be the most effective cross-training modalities to incorporate in early season training to improve running performance in high school runners.

Population pharmacokinetic model of lithium and drug compliance assessment.

PubMed

Pérez-Castelló, Isabel; Mangas-Sanjuan, Víctor; González-García, Ignacio; Gonzalez-Alvarez, Isabel; Bermejo, Marival; Marco-Garbayo, Jose Luis; Trocóniz, Iñaki F

2016-12-01

Population pharmacokinetic analysis of lithium during therapeutic drug monitoring and drug compliance assessment was performed in 54 patients and 246 plasma concentrations levels were included in this study. Patients received several treatment cycles (1-9) and one plasma concentration measurement for each patient was obtained always before starting next cycle (pre-dose) at steady state. Data were analysed using the population approach with NONMEM version 7.2. Lithium measurements were described using a two-compartment model (CL/F=0.41Lh -1 , V 1 /F=15.3L, Q/F=0.61Lh -1 , and V 2 /F = 15.8L) and the most significant covariate on lithium CL was found to be creatinine clearance (reference model). Lithium compliance was analysed using inter-occasion variability or Markovian features (previous lithium measurement as ordered categorical covariate) on bioavailability parameter. Markov-type model predicted the lithium compliance in the next cycle with higher success rate (79.8%) compared to IOV model (65.2%) and reference model (43.2%). This model becomes an efficient tool, not only being able to adequately describe the observed outcome, but also to predict the individual drug compliance in the next cycle. Therefore, Bipolar disorder patients can be classified regarding their probability to become extensive or poor compliers in the next cycle and then, individual probabilities lower than 0.5 highlight the need of intensive monitoring, as well as other pharmaceutical care measurements that might be applied to enhance drug compliance for a better and safer lithium treatment. Copyright © 2016 Elsevier B.V. and ECNP. All rights reserved.

Reinforcing properties of an intermittent, low dose of ketamine in rats: effects of sex and cycle.

PubMed

Wright, Katherine N; Strong, Caroline E; Addonizio, Marjorie N; Brownstein, Naomi C; Kabbaj, Mohamed

2017-02-01

Repeated intermittent exposure to ketamine has rapid and long-lasting antidepressant effects, but the abuse potential has only been assessed at high doses. Furthermore, while females are more susceptible to depression and more sensitive to ketamine's antidepressant-like effects, the abuse potential for ketamine in females is unknown. The objectives of this study are to determine the reinforcing properties of low-dose intermittent ketamine in adult rats of both sexes and determine whether cycling gonadal hormones influence females' response to ketamine. In male rats, we also aimed to determine whether reinstatement to intermittent ketamine is comparable to intermittent cocaine. Male rats intravenously self-administered cocaine (0.75 mg/kg/infusion) or ketamine (0.1 mg/kg/infusion) once every fourth day, while intact cycling female rats self-administered ketamine only during preidentified stages of their 4-day estrus cycle, when gonadal hormones are either high (proestrus) or low (diestrus). After acquiring self-administration, rats underwent daily extinction training followed by cue-primed and drug-primed reinstatement to assess drug-seeking behavior. Diestrus-trained females fail to maintain ketamine self-administration and did not display reinstatement to ketamine-paired cues. Males and proestrus-trained females reinstated to ketamine-paired cues. Ketamine-primed reinstatement was dependent on simultaneous cue presentation. Male rats reinstated to cocaine priming independent of cue presentation. These findings indicate that females's responsivity to this dose of ketamine depends on stage of cycle, as only proestrus-trained females and males respond to ketamine's reinforcing effects under this treatment paradigm.

Sleep-wake Cycle Assessment in Type 2 Diabetes and Salivary Melatonin Correlates

NASA Astrophysics Data System (ADS)

Cavalcanti, Paula Regina Aguiar

The aim of this study was to analyze the sleep-wake cycle of T2DM subjects and compare it to healthy controls using the nonparametric approach and to assess the changes in the circadian and homeostatic control of the sleep-wake cycle in type 2 diabetic (T2DM) and correlate it with melatonin concentration. The sample consisted of 21 subjects with diagnosis of T2DM for more than a year and 21 healthy controls matched for gender and age. Subjects were assessed using the Beck's Depression Inventory (BDI), the Apnea Risk Evaluation System (ARES), hemoglobin A1c (HbA1c), actigraphy and melatonin levels. The findings revealed that T2DM subjects demonstrate lower IS (p=.03), higher IV (p=.046) and lower rhythm amplitude (p=.02) when compared to healthy controls. Mean melatonin concentrations collected at bed time were significantly lower in the diabetic subjects than that of controls (11.7+/-7.27 pg/ml vs. 24.13+/-10.80pg/ml; p<.01). Actigraphic analysis during the wake phase demonstrated that diabetic subjects showed lower levels of activity (p=.02). Additionally, there was a significant difference decrease in sleep duration (p=.03), efficiency (p=.02); and higher activity counts during the sleep phase (p=.02) in the diabetic group. Sleep efficiency was significantly correlated with melatonin collected two hours before bed time (rho=.61; p=.047). Additionally, there were significant inverse relationships between melatonin collected at two hours before bed time and latency (rho=-.87; p=.001), wake after sleep onset (rho=-.69; p=.02) and nocturnal activity (rho=-.67; p=.03). Latency was inversely correlated with melatonin collected at bed time (rho=-.69; p=.02). These findings suggest that T2DM presents disturbances in the homeostatic and circadian drives, mainly characterized by less consistency across days of the daily circadian signal, higher rhythm fragmentation and lower rhythm amplitude. In addition to the lower melatonin levels, the decrease in the amplitude of the activity rhythm may also be involved in circadian alterations of the sleep-wake cycle.

Association between sleep duration and menstrual cycle irregularity in Korean female adolescents.

PubMed

Nam, Ga Eun; Han, Kyungdo; Lee, Gyungjoo

2017-07-01

The association between sleep and the menstrual cycle in the adolescent population has been scarcely studied. This study aimed to investigate the association between sleep duration and menstrual cycle irregularity among female adolescents using nationwide representative data from the South Korean population. This population-based, cross-sectional study used the data collected from Korea National Health and Nutrition Examination Survey 2010-2012, and the data from 801 female adolescents were analyzed. Hierarchical multivariable logistic regression analysis was performed to assess the risk of menstrual cycle irregularity in relation to sleep duration. Subjects with menstrual cycle irregularity accounted for 15% (N = 120). The mean sleep duration in subjects with menstrual cycle irregularity was significantly shorter than that in those without (p = 0.003). Menstrual cycle irregularity prevalence tended to decrease as sleep duration increased (p for trend = 0.004), which was significantly different based on sleep duration and presence of depressive mood (p = 0.011). Sleep duration ≤5 h per day was significantly associated with increased risk of menstrual cycle irregularity compared with that in the subjects whose sleep duration is ≥8 h per day even after adjusting for confounding variables. The odds ratios of menstrual cycle irregularity tended to increase for shorter sleep duration in all adjusted models. This study found a significant inverse association between sleep duration and menstrual cycle irregularity among Korean female adolescents. Increasing sleep duration is required to improve the reproductive health of female adolescents. Copyright © 2017 Elsevier B.V. All rights reserved.

DETECTING PLANETARY GEOCHEMICAL CYCLES ON EXOPLANETS: ATMOSPHERIC SIGNATURES AND THE CASE OF SO{sub 2}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaltenegger, L.; Sasselov, D., E-mail: lkaltene@cfa.harvard.ed

2010-01-10

We study the spectrum of a planetary atmosphere to derive detectable features in low resolution of different global geochemical cycles on exoplanets-using the sulfur cycle as our example. We derive low-resolution detectable features for first generation space- and ground-based telescopes as a first step in comparative planetology. We assume that the surfaces and atmospheres of terrestrial exoplanets (Earth-like and super-Earths) will most often be dominated by a specific geochemical cycle. Here we concentrate on the sulfur cycle driven by outgassing of SO{sub 2} and H{sub 2}S followed by their transformation to other sulfur-bearing species, which is clearly distinguishable from themore » carbon cycle, which is driven by outgassing of CO{sub 2}. Due to increased volcanism, the sulfur cycle is potentially the dominant global geochemical cycle on dry super-Earths with active tectonics. We calculate planetary emission, reflection, and transmission spectrum from 0.4 mum to 40 mum with high and low resolution to assess detectable features using current and Archean Earth models with varying SO{sub 2} and H{sub 2}S concentrations to explore reducing and oxidizing habitable environments on rocky planets. We find specific spectral signatures that are observable with low resolution in a planetary atmosphere with high SO{sub 2} and H{sub 2}S concentration. Therefore, first generation space- and ground-based telescopes can test our understanding of geochemical cycles on rocky planets and potentially distinguish planetary environments dominated by the carbon and sulfur cycles.« less

A study of characteristics of intercity transportation systems. Phase 1: Definition of transportation comparison methodology

NASA Technical Reports Server (NTRS)

English, J. M.; Smith, J. L.; Lifson, M. W.

1978-01-01

Decision making in early transportation planning must be responsive to complex value systems representing various policies and objectives. The assessment of alternative transportation concepts during the early initial phases of the system life cycle, when supportive research and technology development activities are defined, requires estimates of transportation, environmental, and socio-economic impacts throughout the system life cycle, which is a period of some 40 or 50 years. A unified methodological framework for comparing intercity passenger and freight transportation systems is described and is extended to include the comparison of long term transportation trends arising from implementation of the various R & D programs. The attributes of existing and future transportation systems are reviewed in order to establish measures for comparison, define value functions, and attribute weightings needed for comparing alternative policy actions for furthering transportation goals. Comparison criteria definitions and an illustrative example are included.

Short-term effects of salinity reduction and drainage on salt-marsh biogeochemical cycling and Spartina (Cordgrass) production

USGS Publications Warehouse

Portnoy, J.W.; Valiela, I.

1997-01-01

To assess the biogeochemical effects of tidal restrictions on salt-marsh sulfur cycling and plant growth, cores of short-form Spartina alterniflora peat were desalinated and kept either waterlogged or drained in greenhouse microcosms. Changes in net Spartina production, and porewater and solid phase chemistry of treated cores were compared to natural conditions in the field collection site over a 21-mo period. Net production among treatments increased significantly in drained and waterlogged peat compared to field conditions during the first growing season. Constantly high sulfide in waterlogged cores accompanied reduced plant growth. Aeration invigorated growth in drained cores but led to oxidization of sulfide minerals and to lowered pH. During the second growing season, growth declined in the drained treatment, probably because of acidification and decreased dissolved inorganic nitrogen. Results are pertinent to the success of current wetland protection and restoration activities in the coastal zone.

Is it better to remove pharmaceuticals in decentralized or conventional wastewater treatment plants? A life cycle assessment comparison.

PubMed

Igos, Elorri; Benetto, Enrico; Venditti, Silvia; Kohler, Christian; Cornelissen, Alex; Moeller, Ruth; Biwer, Arno

2012-11-01

After ingestion, pharmaceuticals are excreted unchanged or metabolized. They subsequently arrive in conventional wastewater treatment plants and are then released into the environment, often without undergoing any degradation. Conventional treatment plants can be upgraded with post treatment, alternatively the removal of pharmaceuticals could be achieved directly at point sources. In the European project PILLS, several solutions for decentralized treatment of pharmaceuticals at hospitals were investigated at both pilot plant and full scale, and were then compared to conventional and upgraded centralized treatment plants using Life Cycle Assessment (LCA). Within the scope of the study, pharmaceuticals were found to have a comparatively minor environmental impact. As a consequence, an additional post treatment does not provide significant benefits. In the comparison of post treatment technologies, ozonation and activated carbon performed better than UV. These results suffer however from high uncertainties due to the assessment models of the toxicity of pharmaceuticals in LCA. Our results should therefore be interpreted with caution. LCA is a holistic approach and does not cover effects or issues on a local level, which may be highly relevant. We should therefore apply the precautionary ALARA principle (As Low As Reasonably Achievable) and not conclude that the effect of pharmaceuticals is negligible in the environment. Copyright © 2012 Elsevier B.V. All rights reserved.

Children's GPS-determined versus self-reported transport in leisure time and associations with parental perceptions of the neighborhood environment.

PubMed

Vanwolleghem, Griet; Schipperijn, Jasper; Gheysen, Freja; Cardon, Greet; De Bourdeaudhuij, Ilse; Van Dyck, Delfien

2016-05-05

This study aimed to examine both GPS-determined and self-reported walking, cycling and passive transport in leisure time during week- and weekend-days among 10 to 12-year old children. Comparisons between GPS-determined and self-reported transport in leisure time were investigated. Second, associations between parental perceptions of the neighborhood environment and GPS-determined walking, cycling and passive transport in leisure time were studied. Children (10 to 12-years old; n = 126) wore a GPS device and an accelerometer for 7 consecutive days to assess objectively measured transport in leisure time and filled out a diary to assess self-reported transport in leisure time. Parents completed a questionnaire to assess parental perceptions of the neighborhood environment. Pearson correlations and t-tests were used to test for concurrent validity and differences between GPS-determined and self-reported transport in leisure time. Generalized linear models were used to determine the associations between the parental perceptions of the neighborhood environment and GPS-determined transport in leisure time. Overall, children under-reported their walking and cycling in leisure time, compared to GPS-determined measures (all p values <0.001). However, children reported their passive transport in leisure time during weekend days quite accurate. GPS-determined measures revealed that children walked most during weekdays (M = 3.96 trips/day; 26.10 min/day) and used passive transport more frequently during weekend days (M = 2.12 trips/day; 31.39 min/day). Only a few parental perceived environmental attributes of the neighborhood (i.e. residential density, land use mix access, quality and availability of walking and cycling facilities, and aesthetics) were significantly associated with children's GPS-determined walking, cycling or passive transport in leisure time. To accurately assess children's active transport in leisure time, GPS measures are recommended over self-reports. More research using GPS with a focus on children's transport in leisure time and investigating the associations with parental perceptions of the neighborhood environment is needed to confirm the results of the present study.

A Methodology for Integrated, Multiregional Life Cycle Assessment Scenarios under Large-Scale Technological Change.

PubMed

Gibon, Thomas; Wood, Richard; Arvesen, Anders; Bergesen, Joseph D; Suh, Sangwon; Hertwich, Edgar G

2015-09-15

Climate change mitigation demands large-scale technological change on a global level and, if successfully implemented, will significantly affect how products and services are produced and consumed. In order to anticipate the life cycle environmental impacts of products under climate mitigation scenarios, we present the modeling framework of an integrated hybrid life cycle assessment model covering nine world regions. Life cycle assessment databases and multiregional input-output tables are adapted using forecasted changes in technology and resources up to 2050 under a 2 °C scenario. We call the result of this modeling "technology hybridized environmental-economic model with integrated scenarios" (THEMIS). As a case study, we apply THEMIS in an integrated environmental assessment of concentrating solar power. Life-cycle greenhouse gas emissions for this plant range from 33 to 95 g CO2 eq./kWh across different world regions in 2010, falling to 30-87 g CO2 eq./kWh in 2050. Using regional life cycle data yields insightful results. More generally, these results also highlight the need for systematic life cycle frameworks that capture the actual consequences and feedback effects of large-scale policies in the long term.

Energy-containing beverages: reproductive hormones and ovarian function in the BioCycle Study123

PubMed Central

Schliep, Karen C; Mumford, Sunni L; Pollack, Anna Z; Perkins, Neil J; Ye, Aijun; Zhang, Cuilin J; Stanford, Joseph B; Porucznik, Christina A; Hammoud, Ahmad O; Wactawski-Wende, Jean

2013-01-01

Background: Energy-containing beverages are widely consumed among premenopausal women, but their association with reproductive hormones is not well understood. Objective: The objective was to assess the association of energy-containing beverages, added sugars, and total fructose intake with reproductive hormones among ovulatory cycles and sporadic anovulation in healthy premenopausal women. Design: Women (n = 259) in the BioCycle Study were followed for up to 2 menstrual cycles; they provided fasting blood specimens during up to 8 visits/cycle and four 24-h dietary recalls/cycle. Results: Women who consumed ≥1 cup (1 cup = 237 mL) sweetened soda/d had 16.3% higher estradiol concentrations compared with women who consumed less sweetened soda (86.5 pg/mL compared with 74.4 pg/mL, P = 0.01) after adjustment for age, BMI, race, dietary factors, and physical activity. Similarly elevated estradiol concentrations were found for ≥1 cup cola/d and noncola soda intake. Neither artificially sweetened soda nor fruit juice intake ≥1 cup/d was significantly associated with reproductive hormones. Added sugar above the average US woman's intake (≥73.2 g/d) or above the 66th percentile in total fructose intake (≥41.5 g/d) was associated with significantly elevated estradiol but not consistently across all models. No associations were found between beverages, added sugars, or total fructose intake and anovulation after multivariate adjustment. Conclusions: Even at moderate consumption amounts, sweetened soda is associated with elevated follicular estradiol concentrations among premenopausal women but does not appear to affect ovulatory function. Further research into the mechanism driving the association between energy-containing beverages and reproductive hormones, and its potential implications for women's health, is warranted. PMID:23364018

Energy-containing beverages: reproductive hormones and ovarian function in the BioCycle Study.

PubMed

Schliep, Karen C; Schisterman, Enrique F; Mumford, Sunni L; Pollack, Anna Z; Perkins, Neil J; Ye, Aijun; Zhang, Cuilin J; Stanford, Joseph B; Porucznik, Christina A; Hammoud, Ahmad O; Wactawski-Wende, Jean

2013-03-01

Energy-containing beverages are widely consumed among premenopausal women, but their association with reproductive hormones is not well understood. The objective was to assess the association of energy-containing beverages, added sugars, and total fructose intake with reproductive hormones among ovulatory cycles and sporadic anovulation in healthy premenopausal women. Women (n = 259) in the BioCycle Study were followed for up to 2 menstrual cycles; they provided fasting blood specimens during up to 8 visits/cycle and four 24-h dietary recalls/cycle. Women who consumed ≥1 cup (1 cup = 237 mL) sweetened soda/d had 16.3% higher estradiol concentrations compared with women who consumed less sweetened soda (86.5 pg/mL compared with 74.4 pg/mL, P = 0.01) after adjustment for age, BMI, race, dietary factors, and physical activity. Similarly elevated estradiol concentrations were found for ≥1 cup cola/d and noncola soda intake. Neither artificially sweetened soda nor fruit juice intake ≥1 cup/d was significantly associated with reproductive hormones. Added sugar above the average US woman's intake (≥73.2 g/d) or above the 66th percentile in total fructose intake (≥41.5 g/d) was associated with significantly elevated estradiol but not consistently across all models. No associations were found between beverages, added sugars, or total fructose intake and anovulation after multivariate adjustment. Even at moderate consumption amounts, sweetened soda is associated with elevated follicular estradiol concentrations among premenopausal women but does not appear to affect ovulatory function. Further research into the mechanism driving the association between energy-containing beverages and reproductive hormones, and its potential implications for women's health, is warranted.

Low-dose levonorgestrel and ethinyl estradiol patch and pill: a randomized controlled trial.

PubMed

Kaunitz, Andrew M; Portman, David; Westhoff, Carolyn L; Archer, David F; Mishell, Daniel R; Rubin, Arkady; Foegh, Marie

2014-02-01

To compare a new low-dose levonorgestrel and ethinyl estradiol contraceptive patch (Patch) with a combination oral contraceptive (Pill; 100 micrograms levonorgestrel, 20 micrograms ethinyl estradiol) regarding efficacy, safety, compliance, and unscheduled uterine bleeding. Women (17-40 years; body mass index 16-60) were randomized in a 3:1 ratio to one of two groups: Patch only (13 cycles) or Pill (six cycles) followed by Patch (seven cycles). Investigators evaluated adverse events during cycles 2, 4, 6, 9, and 13. Participants recorded drug administration and uterine bleeding on daily diary cards. Compliance was assessed by measuring levonorgestrel and ethinyl estradiol plasma levels. Pearl Index (pregnancies per 100 woman-years) was calculated to evaluate efficacy. Participants (N=1,504) were randomized to Patch (n=1,129) or Pill (n=375). Approximately 30% were obese, more than 40% were racial or ethnic minorities, and more than 55% were new users of hormonal contraceptives. Laboratory-verified noncompliance (undetectable plasma drug levels) was 11% of Patch and 12.6% of Pill users at cycle 6. Pearl Indices (95% confidence intervals) for the intention-to-treat population (cycles 1-6) were 4.45 (2.34-6.57) for Patch and 4.02 (0.50-7.53) for Pill; excluding laboratory-verified noncompliant participants, Pearl Indices were 2.82 (0.98-4.67) for Patch and 3.80 (0.08-7.52) for Pill (differences not statistically significant). Incidence of unscheduled bleeding and incidence and severity of adverse events were similar for both contraceptives (no statistically significant difference). Efficacy and safety of the new contraceptive Patch are comparable to those of a Pill. Laboratory-verified noncompliance and bleeding profile are similar between the two treatments. The Patch was well tolerated. ClinicalTrials.gov, www.clinicaltrials.gov, NCT01181479. I.

Job enlargement and mechanical exposure variability in cyclic assembly work.

PubMed

Möller, Therése; Mathiassen, Svend Erik; Franzon, Helena; Kihlberg, Steve

2004-01-15

Cyclic assembly work is known to imply a high risk for musculoskeletal disorders. To have operators rotate between work tasks is believed to be one way of decreasing this risk, since it is expected to increase variation in mechanical and psychological exposures (physical and mental loads). This assumption was investigated by assessing mechanical exposure variability in three assembly tasks in an electronics assembly plant, each on a separate workstation, as well as in a 'job enlargement' scenario combining all three stations. Five experienced operators worked for 1 h on each station. Data on upper trapezius and forearm extensor muscle activity were obtained by means of electromyography (EMG), and working postures of the head and upper arms were assessed by inclinometry. The cycle-to-cycle variance of parameters representing the three exposure dimensions: level, frequency and duration was estimated using ANOVA algorithms for each workstation separately as well as for a balanced combination of all three. For a particular station, the variability of trapezius EMG activity levels relative to the mean was higher than for extensor EMG: between-cycles coefficients of variation (CV) about 0.15 and 0.10, respectively. A similar relationship between CV applied to the parameter describing frequency of EMG activity. Except for head inclination levels, the between-cycles CV was larger for posture parameters than for EMG. The between-cycles variance increased up to six fold in the job enlargement scenario, as compared to working at only one station. The difference in mean exposure between workstations was larger for trapezius EMG parameters than for forearm extensor EMG and postures, and hence the effect of job enlargement on exposure variability was more pronounced for the trapezius. For some stations, job enlargement even implied less cycle-to-cycle variability in forearm extensor EMG parameters than working at that station only. Whether the changes in exposure variability associated with job enlargement were sufficient to imply a decreased risk for musculoskeletal disorders is not known.

Cradle-to-gate life-cycle assessment of laminated veneer lumber produced in the southeast region of the United States

Treesearch

Richard D. Bergman; Sevda Alanya-Rosenbaum

2017-01-01

The goal of the present study was to develop life-cycle impact assessment (LCIA) data associated with gate-to-gate laminated veneer lumber (LVL) production in the southeast (SE) region of the U.S. with the ultimate aim of constructing an updated cradle-to-gate mill output life-cycle assessment (LCA). The authors collected primary (survey) mill data from LVL production...

Life Cycle Assessment Perspectives on Delivering an Infant in the US

PubMed Central

Campion, Nicole; Thiel, Cassandra L.; DeBlois, Justin; Woods, Noe C.; Landis, Amy E.; Bilec, Melissa M.

2012-01-01

This study introduces life cycle assessment as a tool to analyze one aspect of sustainability in healthcare: the birth of a baby. The process life cycle assessment case study presented evaluates two common procedures in a hospital, a cesarean section and a vaginal birth. This case study was conducted at Magee-Womens Hospital of the University of Pittsburgh Medical Center, which delivers over 10,000 infants per year. The results show that heating, ventilation, and air conditioning (HVAC), waste disposal, and the production of the disposable custom packs comprise a large percentage of the environmental impacts. Applying the life cycle assessment tool to medical procedures allows hospital decision makers to target and guide efforts to reduce the environmental impacts of healthcare procedures. PMID:22482785

Influence of number of dental autoclave treatment cycles on rotational performance of commercially available air-turbine handpieces.

PubMed

Nagai, Masahiro; Takakuda, Kazuo

2006-06-01

The influence of number of autoclave treatment cycles (N) on rotational speed and total indicated run-out of commercially available air-turbine handpieces from five manufacturers was investigated at N=0, 50, 100, 150, 200, 250 and 300 cycles, and the significance in the test results was assessed by Dunnett's multiple comparison test. Some air-turbine handpieces showed the significant differences in rotational speed at N=300 cycles, however, the decreases of the rotational speeds were only 1 to 3.5 percent. Some air-turbine handpieces showed the significant differences in total indicated run-out, however, the respective values were smaller than that at N=0 cycle. Accordingly, it can be considered that the ball bearing in the air-turbine handpieces is not affected significantly by autoclave. To further evaluate rotational performance, this study focused on the rotational vibration of the ball bearing components of the air-turbine, as measured by Fast Fourier Transform (FFT) analysis; the power spectra of frequency of the ball's revolution, frequency of the cage's rotation and frequency of the ball's rotation were comparatively investigated at N=0, 150 and 300 cycles, and the influence of autoclave was evaluated qualitatively. No abnormalities in the ball bearings were recognized.

A life cycle assessment and economic analysis of the Scum-to-Biodiesel technology in wastewater treatment plants.

PubMed

Mu, Dongyan; Addy, Min; Anderson, Erik; Chen, Paul; Ruan, Roger

2016-03-01

This study used life cycle assessment and technical economic analysis tools in evaluating a novel Scum-to-Biodiesel technology and compares the technology with scum digestion and combustion processes. The key variables that control environmental and economic performance are identified and discussed. The results show that all impacts examined for the Scum-to-Biodiesel technology are below zero indicating significant environmental benefits could be drawn from it. Of the three technologies examined, the Scum-to-Biodiesel technology has the best environmental performance in fossil fuel depletion, GHG emissions, and eutrophication, whereas combustion has the best performance on acidification. Of all process inputs assessed, process heat, glycerol, and methanol uses had the highest impacts, much more than any other inputs considered. The Scum-to-Biodiesel technology also makes higher revenue than other technologies. The diesel price is a key variable for its economic performance. The research demonstrates the feasibility and benefits in developing Scum-to-Biodiesel technology in wastewater treatment facilities. Copyright © 2015 Elsevier Ltd. All rights reserved.

Human circadian pacemaker is sensitive to light throughout subjective day without evidence of transients

NASA Technical Reports Server (NTRS)

Jewett, M. E.; Rimmer, D. W.; Duffy, J. F.; Klerman, E. B.; Kronauer, R. E.; Czeisler, C. A.

1997-01-01

Fifty-six resetting trials were conducted across the subjective day in 43 young men using a three-cycle bright-light (approximately 10,000 lx). The phase-response curve (PRC) to these trials was assessed for the presence of a "dead zone" of photic insensitivity and was compared with another three-cycle PRC that had used a background of approximately 150 lx. To assess possible transients after the light stimulus, the trials were divided into 43 steady-state trials, which occurred after several baseline days, and 13 consecutive trials, which occurred immediately after a previous resetting trial. We found that 1) bright light induces phase shifts throughout subjective day with no apparent dead zone; 2) there is no evidence of transients in constant routine assessments of the fitted temperature minimum 1-2 days after completion of the resetting stimulus; and 3) the timing of background room light modulates the resetting response to bright light. These data indicate that the human circadian pacemaker is sensitive to light at virtually all circadian phases, implying that the entire 24-h pattern of light exposure contributes to entrainment.

A case study of packaging waste collection systems in Portugal - Part II: Environmental and economic analysis.

PubMed

Pires, Ana; Sargedas, João; Miguel, Mécia; Pina, Joaquim; Martinho, Graça

2017-03-01

An understanding of the environmental impacts and costs related to waste collection is needed to ensure that existing waste collection schemes are the most appropriate with regard to both environment and cost. This paper is Part II of a three-part study of a mixed packaging waste collection system (curbside plus bring collection). Here, the mixed collection system is compared to an exclusive curbside system and an exclusive bring system. The scenarios were assessed using life cycle assessment and an assessment of costs to the waste management company. The analysis focuses on the collection itself so as to be relevant to waste managers and decision-makers who are involved only in this step of the packaging life cycle. The results show that the bring system has lower environmental impacts and lower economic costs, and is capable of reducing the environmental impacts of the mixed system. However, a sensitivity analysis shows that these results could differ if the curbside collection were to be optimized. From economic and environmental perspectives, the mixed system has few advantages. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison between fluorescent in-situ hybridisation and array comparative genomic hybridisation in preimplantation genetic diagnosis in translocation carriers.

PubMed

Lee, Vivian C Y; Chow, Judy F C; Lau, Estella Y L; Yeung, William S B; Ho, P C; Ng, Ernest H Y

2015-02-01

To compare the pregnancy outcome of the fluorescent in-situ hybridisation and array comparative genomic hybridisation in preimplantation genetic diagnosis of translocation carriers. Historical cohort. A teaching hospital in Hong Kong. All preimplantation genetic diagnosis treatment cycles performed for translocation carriers from 2001 to 2013. Overall, 101 treatment cycles for preimplantation genetic diagnosis in translocation were included: 77 cycles for reciprocal translocation and 24 cycles for Robertsonian translocation. Fluorescent in-situ hybridisation and array comparative genomic hybridisation were used in 78 and 11 cycles, respectively. The ongoing pregnancy rate per initiated cycle after array comparative genomic hybridisation was significantly higher than that after fluorescent in-situ hybridisation in all translocation carriers (36.4% vs 9.0%; P=0.010). The miscarriage rate was comparable with both techniques. The testing method (array comparative genomic hybridisation or fluorescent in-situ hybridisation) was the only significant factor affecting the ongoing pregnancy rate after controlling for the women's age, type of translocation, and clinical information of the preimplantation genetic diagnosis cycles by logistic regression (odds ratio=1.875; P=0.023; 95% confidence interval, 1.090-3.226). This local retrospective study confirmed that comparative genomic hybridisation is associated with significantly higher pregnancy rates versus fluorescent in-situ hybridisation in translocation carriers. Array comparative genomic hybridisation should be the technique of choice in preimplantation genetic diagnosis cycles in translocation carriers.

Isolation of Mitochondrial DNA from Single, Short Hairs without Roots Using Pressure Cycling Technology.

PubMed

Harper, Kathryn A; Meiklejohn, Kelly A; Merritt, Richard T; Walker, Jessica; Fisher, Constance L; Robertson, James M

2018-02-01

Hairs are commonly submitted as evidence to forensic laboratories, but standard nuclear DNA analysis is not always possible. Mitochondria (mt) provide another source of genetic material; however, manual isolation is laborious. In a proof-of-concept study, we assessed pressure cycling technology (PCT; an automated approach that subjects samples to varying cycles of high and low pressure) for extracting mtDNA from single, short hairs without roots. Using three microscopically similar donors, we determined the ideal PCT conditions and compared those yields to those obtained using the traditional manual micro-tissue grinder method. Higher yields were recovered from grinder extracts, but yields from PCT extracts exceeded the requirements for forensic analysis, with the DNA quality confirmed through sequencing. Automated extraction of mtDNA from hairs without roots using PCT could be useful for forensic laboratories processing numerous samples.

The actions of dihydroxyphenylalanine and dihydroxyphenylserine on the sleep-wakefulness cycle of the rat after peripheral decarboxylase inhibition.

PubMed Central

Altier, H; Moldes, M; Monti, J M

1975-01-01

1. The actions of dihydroxyphenylalanine (DOPA) and dihydroxyphenylserine (DOPS) were assessed on the sleep-wakefulness cycle of male Wistar rats. 2. In comparative studies the extracerebral decarboxylase was inhibited with serinetrihydroxybenzylhydrazide (RO 4-4602) before injection of DOPA or DOPS. 3. DOPA (80-160 mg/kg, i.p.) with or without previous inhibition of the peripheral decarboxylase gave rise to an initial significant increase of slow wave activity, which may be related to a release of 5-hydroxytryptamine. 4. During the subsequent 8 h sessions, DOPA significantly decreased slow wave sleep and rapid eye movement sleep (REM) and increased wakefulness. 5. DOPS (80-160 mg/kg, i.p.) did not significantly modify the sleep-wakefulness cycle apart from a decrease of the latency for the first REM episode after 160 mg/kg in the RO 4-4602 pretreated animals. PMID:166716

Prospects for energy efficiency improvement and reduction of emissions and life cycle costs for natural gas vehicles

NASA Astrophysics Data System (ADS)

Kozlov, A. V.; Terenchenko, A. S.; Luksho, V. A.; Karpukhin, K. E.

2017-01-01

This work is devoted to the experimental investigation of the possibilities to reduce greenhouse gas emissions and to increase energy efficiency of engines that use natural gas as the main fuel and the analysis of economic efficiency of use of dual fuel engines in vehicles compared to conventional diesel. The results of experimental investigation of a 190 kW dual-fuel engine are presented; it is shown that quantitative and qualitative working process control may ensure thermal efficiency at the same level as that of the diesel engine and in certain conditions 5...8% higher. The prospects for reduction of greenhouse gas emissions have been assessed. The technical and economic evaluation of use of dual fuel engines in heavy-duty vehicles has been performed, taking into account the total life cycle. It is shown that it is possible to reduce life cycle costs by two times.

INVO procedure: minimally invasive IVF as an alternative treatment option for infertile couples.

PubMed

Lucena, Elkin; Saa, Angela M; Navarro, Doris E; Pulido, Carlos; Lombana, Oscar; Moran, Abby

2012-01-01

Intravaginal culture (IVC), also called INVO (intravaginal culture of oocytes), is an assisted reproduction procedure where oocyte fertilization and early embryo development are carried out within a gas permeable air-free plastic device, placed into the maternal vaginal cavity for incubation. In the present study we assessed the outcome of the INVO procedure, using the recently designed INVOcell device, in combination with a mild ovarian stimulation protocol. A total of 125 cycles were performed. On average 6.5 oocytes per cycle were retrieved, and a mean of 4.2 were placed per INVOcell device. The cleavage rate obtained after the INVO culture was 63%. The procedure yielded 40%, 31.2%, and 24% of clinical pregnancy, live birth, and single live birth rates per cycle, respectively. Our results suggest that the INVO procedure is an effective alternative treatment option in assisted reproduction that shows comparable results to those reported for existing IVF techniques.

INVO Procedure: Minimally Invasive IVF as an Alternative Treatment Option for Infertile Couples

PubMed Central

Lucena, Elkin; Saa, Angela M.; Navarro, Doris E.; Pulido, Carlos; Lombana, Oscar; Moran, Abby

2012-01-01

Intravaginal culture (IVC), also called INVO (intravaginal culture of oocytes), is an assisted reproduction procedure where oocyte fertilization and early embryo development are carried out within a gas permeable air-free plastic device, placed into the maternal vaginal cavity for incubation. In the present study we assessed the outcome of the INVO procedure, using the recently designed INVOcell device, in combination with a mild ovarian stimulation protocol. A total of 125 cycles were performed. On average 6.5 oocytes per cycle were retrieved, and a mean of 4.2 were placed per INVOcell device. The cleavage rate obtained after the INVO culture was 63%. The procedure yielded 40%, 31.2%, and 24% of clinical pregnancy, live birth, and single live birth rates per cycle, respectively. Our results suggest that the INVO procedure is an effective alternative treatment option in assisted reproduction that shows comparable results to those reported for existing IVF techniques. PMID:22645435

Fluctuation-driven mechanotransduction regulates mitochondrial-network structure and function

NASA Astrophysics Data System (ADS)

Bartolák-Suki, Erzsébet; Imsirovic, Jasmin; Parameswaran, Harikrishnan; Wellman, Tyler J.; Martinez, Nuria; Allen, Philip G.; Frey, Urs; Suki, Béla

2015-10-01

Cells can be exposed to irregular mechanical fluctuations, such as those arising from changes in blood pressure. Here, we report that ATP production, assessed through changes in mitochondrial membrane potential, is downregulated in vascular smooth muscle cells in culture exposed to monotonous stretch cycles when compared with cells exposed to a variable cyclic stretch that incorporates physiological levels of cycle-by-cycle variability in stretch amplitude. Variable stretch enhances ATP production by increasing the expression of ATP synthase’s catalytic domain, cytochrome c oxidase and its tyrosine phosphorylation, mitofusins and PGC-1α. Such a fluctuation-driven mechanotransduction mechanism is mediated by motor proteins and by the enhancement of microtubule-, actin- and mitochondrial-network complexity. We also show that, in aorta rings isolated from rats, monotonous stretch downregulates--whereas variable stretch maintains--physiological vessel-wall contractility through mitochondrial ATP production. Our results have implications for ATP-dependent and mechanosensitive intracellular processes.

The two-stroke poppet valve engine. Part 1: Intake and exhaust ports flow experimental assessments

NASA Astrophysics Data System (ADS)

Kamili Zahidi, M.; Razali Hanipah, M.; Ramasamy, D.; Noor, M. M.; Kadirgama, K.; Rahman, M. M.

2017-10-01

A two-stroke poppet valve engine is developed to overcome the common problems in conventional two-stroke engine designs. However, replacing piston control port with poppet valve will resulted different flow behaviour. This paper is looking at experimental assessment on a two-stroke poppet valve engine configuration to investigate the port flow performance. The aims are to evaluate the intake and exhaust coefficient of discharge and assess the twostroke capability of the cylinder head. The results has shown comparable coefficient of discharge values as production engine for the intake while the exhaust has higher values which is favourable for the two-stroke cycle operation.

A comparative life cycle assessment of material handling systems for sustainable mining.

PubMed

Erkayaoğlu, M; Demirel, N

2016-06-01

In this comprehensive LCA comparison study, main objectives are to investigate life cycle environmental impacts of off-highway mining trucks and belt conveyors in surface mining. The research methodology essentially entails determination of the functional unit as 20,000 tons/day coal production transported for 5 km distance. After the system boundary was selected as the entire life cycle of material handling systems including pre-manufacturing of steel parts and plastic components, manufacturing, transportation, and utilization data was compiled from equipment manufacturers and the Eco-invent database. Life cycle impact categories for both material-handling systems were identified and the developed model was implemented using SIMAPRO 7.3. Climate change and acidification were selected as major impact categories as they were considered to be major concerns in mining industry. Although manufacturing stage had a significant impact on all of the environmental parameters, utilization stage was the hotspot for the selected impact categories. The results of this study revealed that belt conveyors have a greater environmental burden in climate change impact category when compared to the trucks. On the other hand, trucks have a greater environmental burden in acidification impact category when compared to the belt conveyors. This study implied that technological improvement in fuel combustion and electricity generation is crucial for the improvement of environmental profiles of off-highway trucks and belt conveyors in the mining industry. The main novelty of this study is that it is the first initiative in applying LCA in the Turkish mining industry. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing the greenhouse gas emissions of Brazilian soybean biodiesel production.

PubMed

Cerri, Carlos Eduardo Pellegrino; You, Xin; Cherubin, Maurício Roberto; Moreira, Cindy Silva; Raucci, Guilherme Silva; Castigioni, Bruno de Almeida; Alves, Priscila Aparecida; Cerri, Domingos Guilherme Pellegrino; Mello, Francisco Fujita de Castro; Cerri, Carlos Clemente

2017-01-01

Soybean biodiesel (B100) has been playing an important role in Brazilian energy matrix towards the national bio-based economy. Greenhouse gas (GHG) emissions is the most widely used indicator for assessing the environmental sustainability of biodiesels and received particular attention among decision makers in business and politics, as well as consumers. Former studies have been mainly focused on the GHG emissions from the soybean cultivation, excluding other stages of the biodiesel production. Here, we present a holistic view of the total GHG emissions in four life cycle stages for soybean biodiesel. The aim of this study was to assess the GHG emissions of Brazilian soybean biodiesel production system with an integrated life cycle approach of four stages: agriculture, extraction, production and distribution. Allocation of mass and energy was applied and special attention was paid to the integrated and non-integrated industrial production chain. The results indicated that the largest source of GHG emissions, among four life cycle stages, is the agricultural stage (42-51%) for B100 produced in integrated systems and the production stage (46-52%) for B100 produced in non-integrated systems. Integration of industrial units resulted in significant reduction in life cycle GHG emissions. Without the consideration of LUC and assuming biogenic CO2 emissions is carbon neutral in our study, the calculated life cycle GHG emissions for domestic soybean biodiesel varied from 23.1 to 25.8 gCO2eq. MJ-1 B100 and those for soybean biodiesel exported to EU ranged from 26.5 to 29.2 gCO2eq. MJ-1 B100, which represent reductions by 65% up to 72% (depending on the delivery route) of GHG emissions compared with the EU benchmark for diesel fuel. Our findings from a life cycle perspective contributed to identify the major GHG sources in Brazilian soybean biodiesel production system and they can be used to guide mitigation priority for policy and decision-making. Projected scenarios in this study would be taken as references for accounting the environmental sustainability of soybean biodiesel within a domestic and global level.

A novel colourimetric technique to assess chewing function using two-coloured specimens: Validation and application.

PubMed

Schimmel, Martin; Christou, Panagiotis; Miyazaki, Hideo; Halazonetis, Demetrios; Herrmann, François R; Müller, Frauke

2015-08-01

Chewing efficiency may be evaluated using cohesive specimen, especially in elderly or dysphagic patients. The aim of this study was to evaluate three two-coloured chewing gums for a colour-mixing ability test and to validate a new purpose built software (ViewGum©). Dentate participants (dentate-group) and edentulous patients with mandibular two-implant overdentures (IOD-group) were recruited. First, the dentate-group chewed three different types of two-coloured gum (gum1-gum3) for 5, 10, 20, 30 and 50 chewing cycles. Subsequently the number of chewing cycles with the highest intra- and inter-rater agreement was determined visually by applying a scale (SA) and opto-electronically (ViewGum©, Bland-Altman analysis). The ViewGum© software determines semi-automatically the variance of hue (VOH); inadequate mixing presents with larger VOH than complete mixing. Secondly, the dentate-group and the IOD-group were compared. The dentate-group comprised 20 participants (10 female, 30.3±6.7 years); the IOD-group 15 participants (10 female, 74.6±8.3 years). Intra-rater and inter-rater agreement (SA) was very high at 20 chewing cycles (95.00-98.75%). Gums 1-3 showed different colour-mixing characteristics as a function of chewing cycles, gum1 showed a logarithmic association; gum2 and gum3 demonstrated more linear behaviours. However, the number of chewing cycles could be predicted in all specimens from VOH (all p<0.0001, mixed linear regression models). Both analyses proved discriminative to the dental state. ViewGum© proved to be a reliable and discriminative tool to opto-electronically assess chewing efficiency, given an elastic specimen is chewed for 20 cycles and could be recommended for the evaluation of chewing efficiency in a clinical and research setting. Chewing is a complex function of the oro-facial structures and the central nervous system. The application of the proposed assessments of the chewing function in geriatrics or special care dentistry could help visualising oro-functional or dental comorbidities in dysphagic patients or those suffering from protein-energy malnutrition. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Assessing the greenhouse gas emissions of Brazilian soybean biodiesel production

PubMed Central

You, Xin; Cherubin, Maurício Roberto; Moreira, Cindy Silva; Raucci, Guilherme Silva; Castigioni, Bruno de Almeida; Alves, Priscila Aparecida; Cerri, Domingos Guilherme Pellegrino; Mello, Francisco Fujita de Castro; Cerri, Carlos Clemente

2017-01-01

Soybean biodiesel (B100) has been playing an important role in Brazilian energy matrix towards the national bio-based economy. Greenhouse gas (GHG) emissions is the most widely used indicator for assessing the environmental sustainability of biodiesels and received particular attention among decision makers in business and politics, as well as consumers. Former studies have been mainly focused on the GHG emissions from the soybean cultivation, excluding other stages of the biodiesel production. Here, we present a holistic view of the total GHG emissions in four life cycle stages for soybean biodiesel. The aim of this study was to assess the GHG emissions of Brazilian soybean biodiesel production system with an integrated life cycle approach of four stages: agriculture, extraction, production and distribution. Allocation of mass and energy was applied and special attention was paid to the integrated and non-integrated industrial production chain. The results indicated that the largest source of GHG emissions, among four life cycle stages, is the agricultural stage (42–51%) for B100 produced in integrated systems and the production stage (46–52%) for B100 produced in non-integrated systems. Integration of industrial units resulted in significant reduction in life cycle GHG emissions. Without the consideration of LUC and assuming biogenic CO2 emissions is carbon neutral in our study, the calculated life cycle GHG emissions for domestic soybean biodiesel varied from 23.1 to 25.8 gCO2eq. MJ-1 B100 and those for soybean biodiesel exported to EU ranged from 26.5 to 29.2 gCO2eq. MJ-1 B100, which represent reductions by 65% up to 72% (depending on the delivery route) of GHG emissions compared with the EU benchmark for diesel fuel. Our findings from a life cycle perspective contributed to identify the major GHG sources in Brazilian soybean biodiesel production system and they can be used to guide mitigation priority for policy and decision-making. Projected scenarios in this study would be taken as references for accounting the environmental sustainability of soybean biodiesel within a domestic and global level. PMID:28493965

The effects of engine operating conditions on CCD chemistry and morphology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeh, S.W.; Moore, S.M.; Sabourin, E.T.

1996-10-01

The effects of engine driving cycle and engine coolant temperature on combustion chamber deposit (CCD) surface chemistry and morphology were assessed by the use of XPS and scanning electron micrographs. A 3.1L V6 test cell engine was used to generate a six test matrix that compared deposit surface chemistry and morphology under two distinctly different driving cycles, each cycle being evaluated at three separate engine coolant temperatures. Deposit material for each respective test was collected by removable combustion chamber sample probes that were subjected to XPS surface analysis and SEM evaluation. Discernible trends were observed in surface chemistry and depositmore » amounts with respect to changes in both driving cycle and coolant temperature. However, much more pronounced were deposit morphological changes recorded by SEM in different engine coolant temperature regimes for both of the utilized driving cycles. Deposit nodules formed in one temperature regime were seen to be typically much larger in size, highly irregular in shape, and appeared to be porous in structure. At a different operating temperature, the deposit nodules were observed to be extremely uniform and more tightly packed.« less

Life Cycle Assessment Harmonization | Energy Analysis | NREL

Science.gov Websites

change are excluded from this analysis. The data showed that life cycle greenhouse gas (GHG) emissions Sensitivity Analysis of Biopower Life-Cycle Assessments and Greenhouse Gas Emission, Electric Power Research hydropower, ocean, geothermal, biopower, solar, wind, nuclear, coal, and natural gas technologies. See the

Toward Automated Inventory Modeling in Life Cycle Assessment: The Utility of Semantic Data Modeling to Predict Real-WorldChemical Production

EPA Science Inventory

A set of coupled semantic data models, i.e., ontologies, are presented to advance a methodology towards automated inventory modeling of chemical manufacturing in life cycle assessment. The cradle-to-gate life cycle inventory for chemical manufacturing is a detailed collection of ...

Developing Students' Understanding of Industrially Relevant Economic and Life Cycle Assessments

ERIC Educational Resources Information Center

Bode, Claudia J.; Chapman, Clint; Pennybaker, Atherly; Subramaniam, Bala

2017-01-01

Training future leaders to understand life cycle assessment data is critical for effective research, business, and sociopolitical decision-making. However, the technical nature of these life cycle reports often makes them challenging for students and other nonexperts to comprehend. Therefore, we outline here the key takeaways from recent economic…

Life cycle assessment part 2: current impact assessment practice.

PubMed

Pennington, D W; Potting, J; Finnveden, G; Lindeijer, E; Jolliet, O; Rydberg, T; Rebitzer, G

2004-07-01

Providing our society with goods and services contributes to a wide range of environmental impacts. Waste generation, emissions and the consumption of resources occur at many stages in a product's life cycle-from raw material extraction, energy acquisition, production and manufacturing, use, reuse, recycling, through to ultimate disposal. These all contribute to impacts such as climate change, stratospheric ozone depletion, photooxidant formation (smog), eutrophication, acidification, toxicological stress on human health and ecosystems, the depletion of resources and noise-among others. The need exists to address these product-related contributions more holistically and in an integrated manner, providing complimentary insights to those of regulatory/process-oriented methodologies. A previous article (Part 1, Rebitzer et al., 2004) outlined how to define and model a product's life cycle in current practice, as well as the methods and tools that are available for compiling the associated waste, emissions and resource consumption data into a life cycle inventory. This article highlights how practitioners and researchers from many domains have come together to provide indicators for the different impacts attributable to products in the life cycle impact assessment (LCIA) phase of life cycle assessment (LCA).

Choosing the best image processing method for masticatory performance assessment when using two-coloured specimens.

PubMed

Vaccaro, G; Pelaez, J I; Gil, J A

2016-07-01

Objective masticatory performance assessment using two-coloured specimens relies on image processing techniques; however, just a few approaches have been tested and no comparative studies are reported. The aim of this study was to present a selection procedure of the optimal image analysis method for masticatory performance assessment with a given two-coloured chewing gum. Dentate participants (n = 250; 25 ± 6·3 years) chewed red-white chewing gums for 3, 6, 9, 12, 15, 18, 21 and 25 cycles (2000 samples). Digitalised images of retrieved specimens were analysed using 122 image processing methods (IPMs) based on feature extraction algorithms (pixel values and histogram analysis). All IPMs were tested following the criteria of: normality of measurements (Kolmogorov-Smirnov), ability to detect differences among mixing states (anova corrected with post hoc Bonferroni) and moderate-to-high correlation with the number of cycles (Spearman's Rho). The optimal IPM was chosen using multiple criteria decision analysis (MCDA). Measurements provided by all IPMs proved to be normally distributed (P < 0·05), 116 proved sensible to mixing states (P < 0·05), and 35 showed moderate-to-high correlation with the number of cycles (|ρ| > 0·5; P < 0·05). The variance of the histogram of the Hue showed the highest correlation with the number of cycles (ρ = 0·792; P < 0·0001) and the highest MCDA score (optimal). The proposed procedure proved to be reliable and able to select the optimal approach among multiple IPMs. This experiment may be reproduced to identify the optimal approach for each case of locally available test foods. © 2016 John Wiley & Sons Ltd.

Passive hind-limb cycling improves cardiac function and reduces cardiovascular disease risk in experimental spinal cord injury.

PubMed

West, Christopher R; Crawford, Mark A; Poormasjedi-Meibod, Malihe-Sadat; Currie, Katharine D; Fallavollita, Andre; Yuen, Violet; McNeill, John H; Krassioukov, Andrei V

2014-04-15

Spinal cord injury (SCI) causes altered autonomic control and severe physical deconditioning that converge to drive maladaptive cardiac remodelling. We used a clinically relevant experimental model to investigate the cardio-metabolic responses to SCI and to establish whether passive hind-limb cycling elicits a cardio-protective effect. Initially, 21 male Wistar rats were evenly assigned to three groups: uninjured control (CON), T3 complete SCI (SCI) or T3 complete SCI plus passive hind-limb cycling (SCI-EX; 2 × 30 min day(-1), 5 days week(-1) for 4 weeks beginning 6 days post-SCI). On day 32, cardio-metabolic function was assessed using in vivo echocardiography, ex vivo working heart assessments, cardiac histology/molecular biology and blood lipid profiles. Twelve additional rats (n = 6 SCI and n = 6 SCI-EX) underwent in vivo echocardiography and basal haemodynamic assessments pre-SCI and at days 7, 14 and 32 post-SCI to track temporal cardiovascular changes. Compared with CON, SCI exhibited a rapid and sustained reduction in left ventricular dimensions and function that ultimately manifested as reduced contractility, increased myocardial collagen deposition and an up-regulation of transforming growth factor beta-1 (TGFβ1) and mothers against decapentaplegic homolog 3 (Smad3) mRNA. For SCI-EX, the initial reduction in left ventricular dimensions and function at day 7 post-SCI was completely reversed by day 32 post-SCI, and there were no differences in myocardial contractility between SCI-EX and CON. Collagen deposition was similar between SCI-EX and CON. TGFβ1 and Smad3 were down-regulated in SCI-EX. Blood lipid profiles were improved in SCI-EX versus SCI. We provide compelling novel evidence that passive hind-limb cycling prevents cardiac dysfunction and reduces cardiovascular disease risk in experimental SCI.

Boron neutron capture therapy induces cell cycle arrest and cell apoptosis of glioma stem/progenitor cells in vitro

PubMed Central

2013-01-01

Background Glioma stem cells in the quiescent state are resistant to clinical radiation therapy. An almost inevitable glioma recurrence is due to the persistence of these cells. The high linear energy transfer associated with boron neutron capture therapy (BNCT) could kill quiescent and proliferative cells. Methods The present study aimed to evaluate the effects of BNCT on glioma stem/progenitor cells in vitro. The damage induced by BNCT was assessed using cell cycle progression, apoptotic cell ratio and apoptosis-associated proteins expression. Results The surviving fraction and cell viability of glioma stem/progenitor cells were decreased compared with differentiated glioma cells using the same boronophenylalanine pretreatment and the same dose of neutron flux. BNCT induced cell cycle arrest in the G2/M phase and cell apoptosis via the mitochondrial pathway, with changes in the expression of associated proteins. Conclusions Glioma stem/progenitor cells, which are resistant to current clinical radiotherapy, could be effectively killed by BNCT in vitro via cell cycle arrest and apoptosis using a prolonged neutron irradiation, although radiosensitivity of glioma stem/progenitor cells was decreased compared with differentiated glioma cells when using the same dose of thermal neutron exposure and boronophenylalanine pretreatment. Thus, BNCT could offer an appreciable therapeutic advantage to prevent tumor recurrence, and may become a promising treatment in recurrent glioma. PMID:23915425

Nitrogen fluxes in the forests of the Congo Basin

NASA Astrophysics Data System (ADS)

Bauters, Marijn; Verbeeck, Hans; Cizungu, Landry; Makelele, Isaac; Boeckx, Pascal

2017-04-01

The tropical forest of the Congo basin remains very poorly investigated and understood; mainly because of logistic, political and research capacity constraints. Nevertheless, characterization and monitoring of fundamental processes in this biome is vital to understand future responses and to correctly parameterize Earth system models. Nutrient fluxes are key in these processes for the functioning of tropical forests, since CO2 uptake by terrestrial ecosystems strongly depends on site fertility, i.e. nutrient availability. Accurate projections of future net forest growth and terrestrial CO2 uptake thus necessitate an improved understanding on nutrient cycles and how these are coupled to the carbon (C) cycle in forests. Research in the Congo Basin region should combine assessments of both carbon fluxes and the underlying nutrient cycles which directly impact the forest productivity. We set up a monitoring network for nitrogen fluxes in four different forest types in the Congo Basin, resulting in a unique and integrate dataset. The questions to be answered: How do the N-budgets of four different forest types in the Congo Basin compare? How do these fluxes compare to fluxes in the Amazon forest? What is the influence from the strong slash-and-burn regimes on the N-cycle in the natural forests? We answer these questions with our empirical dataset of one hydrological year, combined with satellite and modeling data.

The compatibility of concurrent high intensity interval training and resistance training for muscular strength and hypertrophy: a systematic review and meta-analysis.

PubMed

Sabag, Angelo; Najafi, Abdolrahman; Michael, Scott; Esgin, Tuguy; Halaki, Mark; Hackett, Daniel

2018-04-16

The purpose of this systematic review and meta-analysis is to assess the effect of concurrent high intensity interval training (HIIT) and resistance training (RT) on strength and hypertrophy. Five electronic databases were searched using terms related to HIIT, RT, and concurrent training. Effect size (ES), calculated as standardised differences in the means, were used to examine the effect of concurrent HIIT and RT compared to RT alone on muscle strength and hypertrophy. Sub-analyses were performed to assess region-specific strength and hypertrophy, HIIT modality (cycling versus running), and inter-modal rest responses. Compared to RT alone, concurrent HIIT and RT led to similar changes in muscle hypertrophy and upper body strength. Concurrent HIIT and RT resulted in a lower increase in lower body strength compared to RT alone (ES = -0.248, p = 0.049). Sub analyses showed a trend for lower body strength to be negatively affected by cycling HIIT (ES = -0.377, p = 0.074) and not running (ES = -0.176, p = 0.261). Data suggests concurrent HIIT and RT does not negatively impact hypertrophy or upper body strength, and that any possible negative effect on lower body strength may be ameliorated by incorporating running based HIIT and longer inter-modal rest periods.

Real Time Fatigue Damage Growth Assessment of a Composite Three-Stringer Panel Using Passive Thermography

NASA Technical Reports Server (NTRS)

Zalameda, Joseph N.; Burke, Eric R.; Horne, Michael R.; Bly, James B.

2015-01-01

Fatigue testing of advanced composite structures is critical to validate both structural designs and damage prediction models. In-situ inspection methods are necessary to track damage onset and growth as a function of load cycles. Passive thermography is a large area, noncontact inspection technique that is used to detect composite damage onset and growth in real time as a function of fatigue cycles. The thermal images are acquired in synchronicity to the applied compressive load using a dual infrared camera acquisition system for full (front and back) coverage. Image processing algorithms are investigated to increase defect contrast areas. The thermal results are compared to non-immersion ultrasound inspections and acoustic emission data.

Life cycle thinking in impact assessment—Current practice and LCA gains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bidstrup, Morten, E-mail: Bidstrup@plan.aau.dk

It has been advocated that life cycle thinking (LCT) should be applied in impact assessment (IA) to a greater extent, since some development proposals pose a risk of significant impacts throughout the interconnected activities of product systems. Multiple authors have proposed the usage of life cycle assessment (LCA) for such analytical advancement, but little to no research on this tool application has been founded in IA practice so far. The aim of this article is to elaborate further on the gains assigned to application of LCA. The research builds on a review of 85 Danish IA reports, which were analysedmore » for analytical appropriateness and application of LCT. Through a focus on the non-technical summary, the conclusion and the use of specific search words, passages containing LCT were searched for in each IA report. These passages were then analysed with a generic framework. The results reveal that LCT is appropriate for most of the IAs, but that LCA is rarely applied to provide such a perspective. Without LCA, the IAs show mixed performance in regard to LCT. Most IAs do consider the product provision of development proposals, but they rarely relate impacts to this function explicitly. Many IAs do consider downstream impacts, but assessments of upstream, distant impacts are generally absent. It is concluded that multiple analytical gains can be attributed to greater application of LCA in IA practice, though some level of LCT already exists. - Highlights: • Life cycle thinking is appropriate across the types and topics of impact assessment. • Yet, life cycle assessment is rarely used for adding such perspective. • Impact assessment practice does apply some degree of life cycle thinking. • However, application of life cycle assessment could bring analytical gains.« less

First insights into cryoballoon-based pulmonary vein isolation taking the individual time-to-isolation into account.

PubMed

Reissmann, Bruno; Wissner, Erik; Deiss, Sebastian; Heeger, Christian; Schlueter, Michael; Wohlmuth, Peter; Lemes, Christine; Mathew, Shibu; Maurer, Tilman; Sohns, Christian; Saguner, Ardan; Santoro, Francesco; Hayashi, Kentaro; Riedl, Johannes; Ouyang, Feifan; Kuck, Karl-Heinz; Metzner, Andreas

2017-10-01

Cryoballoon (CB)-based pulmonary vein isolation (PVI) is an established treatment for symptomatic atrial fibrillation (AF). In the present study, we sought to assess the efficacy and safety of CB-based PVI taking the individual time-to-isolation (TTI) into account. Sixty consecutive patients with drug-refractory paroxysmal atrial fibrillation [n = 49 (82%)] or short-standing persistent atrial fibrillation [n = 11 (18%)] underwent ablation with a 28-mm second-generation CB. The TTI was assessed by spiral mapping-catheter recordings and subsequently followed by an additional freeze-time of 120 s. No bonus freeze-cycle was applied. If the TTI could not be assessed, a fixed freeze-cycle duration of 240 s was applied and successful PVI confirmed thereafter. Clinical follow-up (FU) included 12-lead ECGs and 24 h Holter-ECGs at 3, 6, and 12 months. A blanking period of 3 months was defined. A total of 239 pulmonary veins (PVs) were identified and successfully isolated. The mean TTI assessed in 170/239 (71%) PVs was 52 ± 32 s. The mean number of CB applications was 1.2 ± 0.5; mean freeze-cycle duration was 192 ± 41 s. Mean procedure and fluoroscopy times were 80 ± 24 min and 16 ± 7 min, respectively. Transient phrenic nerve palsy occurred in one patient (2%). During a mean FU of 405 ± 67 days, 43 patients (72%) remained in stable sinus rhythm. Integrating an individual TTI protocol to CB-based PVI results in shorter freeze-cycle applications in a substantial portion of targeted PVs and an arrhythmia-free survival comparable to conventional ablation protocols. The complication rate is low. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2017. For permissions please email: journals.permissions@oup.com.