Science.gov

Sample records for darbs ekonomikas doktora

  1. Upper Paleocene-Lower Eocene biostratigraphy of Darb Gaga, Southeastern Kharga Oasis Western Desert, Egypt

    NASA Astrophysics Data System (ADS)

    Ouda, Khaled; Berggren, William A.; Abdel Sabour, Ayman

    2016-06-01

    Paleontological studies on the Upper Paleocene-Lower Eocene succession at Darb Gaga, southeastern Kharga Oasis, Western Desert, Egypt document the changes associated with the Paleocene-Eocene Thermal Maximum (PETM), such as 1) a radical alteration of the relative and absolute abundance of planktonic foraminifera; 2) a massive occurrence of the excursion planktonic foraminiferal taxa; 3) a widespread deposition of calcarenite yielding atypical (extremely high) faunal abundance associated with the younger phase of warming; and 4) a concentration of coprolites associated with the middle phase of warming. We also document the Lowest Occurrence (LO) of dimorphic larger benthic and excursion foraminifera during the earlier phase of warming at Darb Gaga, as recorded in Bed 1 of the Dababiya Quarry Member. The absence of these faunas in Bed 1 at Dababiya (the GSSP for the P/E Boundary) is likely to be due to both intense deficiency in dissolved oxygen and massive carbonate dissolution. Only remains (fish remains) of faunas that can tolerate the toxicity produced by low oxygen conditions are found in the stratigraphic record of this (oldest) phase at Dababiya. The Dababiya Quarry Member (DQM) at Darb Gaga reflects the unfolding of the sedimentary and biotic changes associated with the PETM global warming at, and following, the Paleocene/Eocene boundary on the southern Tethys platform. The changes began with a rapid increase in bottom and "intermediate" water temperature. The temperature increase was accompanied by removal of oxygen during the early and middle stages of warming. This led to the absence of both subbotinids and calcareous benthic foraminifera in the early and second coprolite-bearing phases (Beds 2 and 3 of the DQM). Dissolution seems to have no role during these stages as shown by the unusual abundance and good preservation of the warm-tolerant Ac. sibaiyaensis. This species reaches its maximum abundance in Bed 2 where it exhibits a broad range of size (63

  2. Geology and origin of the late Proterozoic Darb Zubaydah ophiolite, Kingdom of Saudi Arabia

    USGS Publications Warehouse

    Quick, J.E.

    1990-01-01

    The Darb Zubaydah ophiolite, north-central Arabian Shield, preserves a largely intact section consisting of ultramafic rocks, gabbro, diabase, granodiorite, and interbedded volcanic and sedimentary rocks. Formation of these rocks within or near an island arc is indicated by the absence of pelagic sediments and the abundance of pillow basalt, turbiditic sediments, lahar deposits, and basaltic to rhyolitic tuff. The oldest extrusive rocks formed in a young, relatively unevolved island arc or in a back-arc basin sufficiently close to an arc to receive calc-alkaline lava flows and coarse-grained, arc-derived detritus. Overlying turbidites and lahar deposits of the Kaffan sandstone point to the initiation of a rifting event. High-Ti basalts, which erupted above the Kaffan sandstone, and related diabase are interpreted to be magmatic products of incipient intra-arc rifting. Renewed arc volcanism produced calc-alkaline volcanic rocks that interfingered with the high-Ti basalt and later dominated the section as the volcanic apron of the arc prograded basinward. Extrusion of voluminous calc-alkaline tuff may have been contemporaneous with intrusion of granodiorite and gravity-driven landsliding. -from Author

  3. Reconnaissance geochemical exploration for gold in the Ad Darb area, Kingdom of Saudi Arabia

    USGS Publications Warehouse

    Samater, R.M.; Christian, R.P.; Johnson, P.R.; Bookstrom, A.A.

    1990-01-01

    Overall, metal values in the wadi-sediment samples are low. The known kyanite mineral occurrence is marked by anomalous gold and tin in three minus-80-mesh samples. The low values of the metals do not justify further exploration for the sought deposit type in the immediate vicinity, although the signature of anomalous elements in the wider region is comparable to the signature known in the Carolina Slate Belt, and is permissive of the interpretation that a diffuse hydrothermal system operated in the region during the late Proterozoic. A large concentration of polymetallic anomalies (gold, arsenic, copper, antimony, tin, tungsten, and lead) is outlined in the northeastern part of the survey area on the basis of panned-concentrate samples. The source of the concentration is unknown, and further investigations are recommended. Recommended low-priority investigation of the source of lead and zinc anomalies in the western part of the survey area would be justified as part of a larger program designed to evaluate the mineral potential of the entire belt of Sabya formation rock.

  4. Cutter-Skidder Operator. Competency-Based Training Standards = Conducteur de Debusqueuse-Abatteur d'Arbes. Normes de formation professionnelle basees sur les aptitudes.

    ERIC Educational Resources Information Center

    Ontario Ministry of Skills Development, Toronto.

    This bilingual document contains standards that are based on industry-specific skills identified by labor and management representatives of the forest products industry, successful achievement of which results in issuance of a cutter operator, skidder operator, or cutter-skidder operator Canadian certificate of qualification. With French on all…

  5. Deoxyarbutin Possesses a Potent Skin-Lightening Capacity with No Discernible Cytotoxicity against Melanosomes

    PubMed Central

    Fan, Zhi-Feng; Jiang, Shan; Xu, Shi-Zheng; Lei, Tie-Chi

    2016-01-01

    Safe and effective ingredients capable of removing undesired hyperpigmentation from facial skin are urgently needed for both pharmaceutical and cosmetic purposes. Deoxyarbutin (4-[(tetrahydro-2H-pyran-2-yl) oxy] phenol, D-Arb) is a glucoside derivative of hydroquinone. Here, we investigated the toxicity and efficacy of D-Arb at the sub-cellular level (directly on melanosomes) and skin pigmentation using in vivo and in vitro models to compare with its parent compound hydroquinone (1,4-benzenediol, HQ). At first, we examined the ultrastructural changes of melanosomes in hyperpigmented guinea pig skin induced by 308-nm monochromatic excimer lightand/or treated with HQ and D-Arb using transmission electron microscopy. The results showed that prominent changes in the melanosomal membrane, such as bulb-like structure and even complete rupture of the outer membranes, were found in the skin after topical application of 5% HQ for 10 days. These changes were barely observed in the skin treated with D-Arb. To further clarify whether membrane toxicity of HQ was a direct result of the compound treatment, we also examinedultrastructural changes of individual melanosomes purified from MNT1 human melanoma cells. Similar observations were obtained from the naked melanosome model in vitro. Finally, we determined the effects of melanosomal fractions exposed to HQ or D-Arb on hydroxyl radical generation in the Fenton reaction utilizing an electron spin resonance assay. D-Arb-treated melanosomesexhibit a moderate hydroxyl radical-scavenging activity, whereas HQ-treated melanosomessignificantly generate more hydroxyl free radicals. This study suggests that D-Arb possesses a potent ability in skin lightening and antioxidation with less melanosome cytotoxicity. PMID:27776184

  6. Darbepoetin Administration in Term and Preterm Neonates.

    PubMed

    Patel, Shrena; Ohls, Robin K

    2015-09-01

    Erythropoiesis-stimulating agents (ESAs) such as erythropoietin have been studied as red cell growth factors in preterm and term infants for more than 20 years. Recent studies have evaluated darbepoetin (Darbe, a long-acting ESA) for both erythropoietic effects and potential neuroprotection. We review clinical trials of Darbe in term and preterm infants, which have reported significant erythropoietic uses and neuroprotective effects. ESAs show great promise in decreasing or eliminating transfusions, and in preventing and treating brain injury in term and preterm infants. PMID:26250917

  7. Getting into hot water Problematizing hot water service demand: The case of Old Cairo

    NASA Astrophysics Data System (ADS)

    Culhane, Thomas Henry

    This dissertation analyzes hot water demand and service infrastructure in two neighboring but culturally distinct communities of the urban poor in the inner-city area of central Cairo. The communities are the Historic Islamic Cairo neighborhood of Darb Al Ahmar at the foot of Al-Azhar park, and the Zurayib neighborhood of Manshiyat Nasser where the Coptic Zabaleen Recyclers live. The study focuses on the demand side of the hot water issue and involves consideration of built-environment infrastructures providing piped water, electricity, bottled gas, sewage, and the support structures (wiring and plumbing) for consumer durables (appliances such as hot water heaters, stoves, refrigerators, air conditioners) as well as water pumps and water storage tanks. The study asks the questions "How do poor communities in Cairo value hot water" and "How do cost, infrastructure and cultural preferences affect which attributes of hot water service are most highly preferred?". To answer these questions household surveys based primarily on the World Bank LSMS modules were administered by professional survey teams from Darb Al Ahmar's Aga Khan Trust for Culture and the Zabaleen's local NGO "Spirit of Youth" in their adjacent conununities in and surrounding historic Cairo. In total 463 valid surveys were collected, (231 from Darb Al Ahmar, 232 from the Zabaleen). The surveys included a contingent valuation question to explore Willingness to Pay for improved hot water service; the surveys queried household assets as proxies for income. The dissertation's findings reveal that one quarter of the residents of Darb Al Ahmar and two-thirds of the residents of Manshiyet Nasser's Zabaleen lack conventional water heating service. Instead they employ various types of stoves and self-built contraptions to heat water, usually incurring considerable risk and opportunity costs. However the thesis explores the notion that this is rational "satisficing" behavior; despite the shortcomings of such self

  8. Groundwater Numerical Modeling, An Application of Remote Sensing, and GIS Techniquies in El Shab area, Western Desert, Egypt

    NASA Astrophysics Data System (ADS)

    Faid, Abdalla; Ismail, Esam

    2016-04-01

    El Shab region is located in south Darb El Arbaieen, western desert of Egypt. It occupies the area between latitudes 22o 00/ and 22o 30/ North and Longitudes 29o 30/ and 30o 00/ East, from southern border of Egypt to the area north Bir Kuraiym and from the area east of east Owienat to the area west Tushka district, its area about 2750 Km2. The famous features; southern part of Darb El Arbaieen road, G Baraqat El Scab El Qarra, Bir Dibis, Bir El Shab and Bir Kuraiym, Interpretation of soil stratification shows layers that are related to Quaternary and Upper-Lower Cretaceous eras. It is dissected by a series of NE-SW striking faults. The regional groundwater flow direction is in SW-NE direction with a hydraulic gradient is 1m / 2km. Mathematical model program has been applied for evaluation of groundwater potentials in the main Aquifer -Nubian Sandstone- in the area of study. Total period of simulation is 100 years. After steady state calibration, two different scenarios are simulated for groundwater development. 21 production wells are installed at the study area and used in the model, with the total discharge for the two scenarios were 105000m3/d, 210000m3/d. The drawdown was 11.8 m and 23.7 m for the two scenarios in the end of 100 year. Contour maps for water heads and drawdown and hydrographs for piezometric head are represented. The drawdown was less than the half of the saturated thickness (the safe yield case).

  9. Small Hydropower in Latvia and Intellectualization of its Operating Systems / Par Mazo HIDROENERĢĒTIKU LATVIJĀ un TĀS Staciju VADĪBAS SISTĒMAS INTELEKTUALIZĀCIJU

    NASA Astrophysics Data System (ADS)

    Mahnitko, A.; Gerhards, J.; Linkevics, O.; Varfolomejeva, R.; Umbrasko, I.

    2013-12-01

    The authors estimate the potential for power generation from water resources of small and medium-sized rivers, which are abundant in Latvia. They propose the algorithm for optimal operation of a small-scale hydropower plant (SHPP) at the chosen optimality criterion in view of the plant's participation in the market. The choice of SHPP optimization algorithm is made based on two mathematical programming methods - dynamic and generalized reduced gradient ones. Approbation of the algorithm is illustrated by an example of optimized SHPP operation. Darbā analizētas tradicionālo un pieejamo vietējo atjaunojamo energoresursu - mazo un vidējo upju hidroresursa izmantošanas iespējas Latvijas enerģētikā. Tiek sniegts faktiskais materiāls šajā jautājumā, kas iegūts, balstoties uz oficiālos avotos publicētiem citu autoru iepriekš veiktajiem pētījumiem. Tiek atzīmēts, ka teritoriju, kas atrodas mazo upju tuvumā un nav ietvertas centralizētās elektroapgādes sistēmā, saimnieciskā apgūšana rada apstākļus patērētāju stimulēšanai izmantot autonomus vietējos energoresursus, ieskaitot hidroenerģiju, izmantojošas mazas jaudas energoiekārtas. Atjaunojamās enerģijas tehnoloģiju un iekārtu pastāvīga attīstība un pilnveidošanās veicinās mazo upju plūsmas izmantošanas elektroenerģijas ražošanas efektivitātes paaugstināšanos. Mūsdienu enerģētikas attīstības koncepcija, kas balstīta uz viedo tīklu (smart grids) izveidi, ļauj paaugstināt mazās hidroenerģētikas darbības efektivitāti, integrējot to elektroenerģētiskajā sistēmā. Mazo hidroelektrostaciju (MHES) darbības vadības sistēmas intelektualizācijas pamatā jābūt kompleksam algoritmam un programmām, kas ļauj tiešsaistes (online) režīmā nodrošināt izdevīgu MHES darbības grafiku (režīmu) maksimālā ienākuma gūšanai, balstoties uz zināmu elektroenerģijas cenas prognozi attiecīgajam laika periodam (diennaktij). MHES darbības optimiz

  10. Identity of Innovative Multifunctional Material Manufacturing Business in Latvia / Inovatīvu Daudzfunkcionālo Materiālu Ražotāju Identitāte Latvijā

    NASA Astrophysics Data System (ADS)

    Geipele, I.; Staube, T.; Ciemleja, G.; Zeltins, N.; Ekmanis, Yu.

    2015-08-01

    The publication comprises the results from the practical scientific investigation to define the profile and distinctions of the Latvian innovative multifunctional material manufacturing industry. The research is carried out by a holistic approach, including expert interviews, qualitative analysis of the official register data, practical survey, and financial data analysis. The paper seeks to give the detailed data on a technological profile of the mentioned representative companies, if there is a synergy or tough competition in the Latvian market. The current research is topical, because it is unique and does not have analogues in Latvia, and the research is timely due to correspondence with recently stated Research and Innovation Strategies for Smart Specialisation in Latvia. The main findings are associated with recognition of the factors that make impact on commercialisation of the finished goods, obtained financial results and planned directions of development of the respondent companies. Publikācija sniedz veiktā zinātniski praktiskā pētījuma rezultātus, kura ietvaros tika noteikts Latvijas inovatīvu daudzfunkcionālo materiālu ražotāju darbības profils un identitāte. Pētījumā tika izmantota kompleksās analīzes metode, kas ietvēra ekspertu intervijas, uzņēmumu oficiāli reģistrēto datu kvalitatīvo analīzi, zinātniski praktisko aptauju, kā arī pētāmo uzņēmumu finanšu darbības rezultātu analīzi. Zinātniskais darbs sniedz izsmeļošu informāciju par mērķa uzņēmumu tehnoloģisko profilu un pēta, vai Latvijas mērķa ražošanas nozarē ir sinerģijas vai sīvās konkurences pazīmes. Šim zinātniskajam pētījumam ir noteikta aktualitāte saskaņā ar tā unikalitāti Latvijas valsts mērogā un atbilstība Viedās specializācijas stratēģijai. Pētījuma galvenie secinājumi ir saistīti ar uzņēmumu produkcijas komercializācijas ietekmējošo faktoru apzināšanu, sasniegtajiem finansiālajiem rezultātiem un pl

  11. Heat-flow measurements at shot points along the 1978 Saudi Arabia seismic deep-refraction line; Part II, Discussion and interpretation

    USGS Publications Warehouse

    Gettings, M.E.

    1982-01-01

    The heat-flow profile across the Arabian Shield from Ar Riyad to Ad Darb and across the Red Sea is examined for compatibility with the lithospheric structure of the area as deduced from geologic and other geophysical data. Broad continental uplift associated with Red Sea rifting is symmetric about the Red Sea axis, and geologic and geochronologic evidence indicate that uplift has occurred mainly in the interval 25-13 Ma (mega-annum) ago. Thermal-profile changes in the upper mantle resulting from an influx of hot material associated with rifting yield the correct order of magnitude of uplift, and this mechanism is suggested as the explanation for the regional doming. A lithospheric section, constructed from seismic refraction, gravity, and regional geologic data, provides the framework for construction of thermal models. Thermal gradient measurements were made in drill holes at five shot points. Geotherms for the Shield, which assume a radiogenic heat-source distribution that decreases exponentially with depth, yield temperatures of about 450?C at a depth of 40 km (base of the crust) for shot points 2 (Sabhah) and 3. The geotherm for shot point 4 (near Bishah) yields a distinctly higher temperature (about 580?C) for the same depth. Static models used to model the heat flow in the oceanic crust of the Red Sea shelf and coastal plain either yield too small a heat flow to match the observed heat flow or give lithosphere thicknesses that are so thin as to be improbable. Dynamic (solid-state accretion) models, which account for mantle flow at the base of the lithosphere, adequately match the observed heat-flow values. In the deep-water trough of the Red Sea, which is presently undergoing active sea-floor spreading, classical models of heat flow for a moving slab with accretion at the spreading center are adequate to explain the average heat-flow level. At shot point 5 (Ad Darb), the anomalous heat flow of 2 HFU (heat-flow units) can be explained in terms of a Shield

  12. Getting into hot water Problematizing hot water service demand: The case of Old Cairo

    NASA Astrophysics Data System (ADS)

    Culhane, Thomas Henry

    This dissertation analyzes hot water demand and service infrastructure in two neighboring but culturally distinct communities of the urban poor in the inner-city area of central Cairo. The communities are the Historic Islamic Cairo neighborhood of Darb Al Ahmar at the foot of Al-Azhar park, and the Zurayib neighborhood of Manshiyat Nasser where the Coptic Zabaleen Recyclers live. The study focuses on the demand side of the hot water issue and involves consideration of built-environment infrastructures providing piped water, electricity, bottled gas, sewage, and the support structures (wiring and plumbing) for consumer durables (appliances such as hot water heaters, stoves, refrigerators, air conditioners) as well as water pumps and water storage tanks. The study asks the questions "How do poor communities in Cairo value hot water" and "How do cost, infrastructure and cultural preferences affect which attributes of hot water service are most highly preferred?". To answer these questions household surveys based primarily on the World Bank LSMS modules were administered by professional survey teams from Darb Al Ahmar's Aga Khan Trust for Culture and the Zabaleen's local NGO "Spirit of Youth" in their adjacent conununities in and surrounding historic Cairo. In total 463 valid surveys were collected, (231 from Darb Al Ahmar, 232 from the Zabaleen). The surveys included a contingent valuation question to explore Willingness to Pay for improved hot water service; the surveys queried household assets as proxies for income. The dissertation's findings reveal that one quarter of the residents of Darb Al Ahmar and two-thirds of the residents of Manshiyet Nasser's Zabaleen lack conventional water heating service. Instead they employ various types of stoves and self-built contraptions to heat water, usually incurring considerable risk and opportunity costs. However the thesis explores the notion that this is rational "satisficing" behavior; despite the shortcomings of such self

  13. Evaluation of the Uniform Field Distortions Produced by a Toroidal Dielectric Body / Novērtējums Viendabīga Elektriskā Lauka Izkropļojumiem, Kurus Rada Toroīda Formas Dielektrisks Ķermenis

    NASA Astrophysics Data System (ADS)

    Krasnitsky, Y. A.; Popov, A. E.; Kalnacs, A.

    2015-08-01

    Distortions of the structure of a uniform electric field when a dielectric body with a toroidal shape is placed in it are considered in the quasi-static approximation. The rate of distortion is proposed to estimate through the effective permittivity of toroid determined by solving the corresponding boundary value problem. Some numerical estimates obtained using specially developed software in the language of Matlab are given. Darbā apskatīts kvazi-statisks tuvinājums viendabīga elektriskā lauka izkropļojumiem gadījumos, kad tajā tiek ievietots dielektrisks toroīda formas ķermenis. Izkropļojumu apmēru tiek piedāvāts novērtēt ar toroīda efektīvo caurlaidību, kas tiek noteikta, atrisinot atbilstošo robežvērtību uzdevumu. Tiek doti skaitliski novērtējumi, kas iegūti, lietojot speciāli valodā Matlab izstrādātu programmatūru.

  14. Effects of Using Channelling Devices to Increase Efficiency of Hydrokinetic Devices

    NASA Astrophysics Data System (ADS)

    Kalnacs, A.; Kalnacs, J.; Mutule, A.; Entins, V.

    2015-04-01

    /vai virzienu, maina spiedienu straumē, minimizē turbulenci. Šajā darbā apskatītas iespējas palielināt hidrokinētisko iekārtu efektivitāti, lietojot šādas ierīces, ka arī metode, kā novērtēt sagaidāmo ieguvumu no minēto ierīču lietošanas. Darbā ir aprēķināts, ka vadotņu izmantošana var palielināt hidrokinētisko iekārtu efektivitāti par vismaz 110%, neradot ne lielas izmaksas, nedz arī būtisku negatīvu ietekmi.

  15. Undercar Electrical Generator for Railway Passenger Cars: Improvement of Efficiency / Dzelzceļa Pasažieru Zemvagona Elektriskā Ģeneratora Efektivitātes Uzlabošana

    NASA Astrophysics Data System (ADS)

    Levin, N.; Kamolins, E.; Gusakov, A.; Pugachev, V.

    2013-04-01

    Passenger cars of the railway transport are being constantly improved, thus becoming ever more comfortable for public conveyance. These cars are fitted with air conditioners, installations for heating and forced ventilation, heaters, refrigerators; lighting, radio and TV sets; communication equipment, etc. All the listed fittings need continuous and secure electricity supply from a primary independent source. The paper considers the possibilities of meeting requirements for particular power supply systems - first of all for undercar generators. At operation of such a high-power generator under rugged conditions it should be highly reliable, possessing a reasonable mass and high efficiency. The existing designs of these generators still do not meet the listed requirements in full measure. To improve the efficiency of the undercar generator it is proposed to integrate its excitation winding into the armature one, thus reducing the copper consumption, losses and mass, while - which is the most important - considerably raising reliability of the generator and its availability factor. Dzelzceļa transporta pasažieru vilcienu vagoni nepārtraukti tiek pilnveidoti ar mērķi paaugstināt pasažieru komforta līmeni pārvadājumu laikā. Šādi pasažieru vagoni aprīkoti ar gaisa kondicionēšanas, apsildes, ventilācijas, ūdens uzsildīšanas, saldēšanas, apgaismes, radio, televīzijas, sakaru u.c. iekārtām. Visām pieminētajām iekārtām to darbības laikā ir nepieciešama nepārtraukta un droša elektroenerģijas apgāde no primāra neatkarīga avota. Darbā tiek izskatīta elektroapgādes sistēma, kura spētu nodrošināt izvirzītās prasības. Pie šīs sistēmas, pirmkārt, pieder zemvagona ģenerators. Tam ir jābūt paaugstinātas jaudas, smagos darba apstākļos jānodrošina augsts drošums, ar pieņemamu masu un augstu lietderības koeficientu. Šādu ģeneratoru esošās konstrukcijas pilnā mērā nespēj nodrošināt iepriekš minētās pras

  16. Multi-Objective Optimization of Transmission Lines / Elektropārvades Līnijas Daudzkriteriālā Optimizācija

    NASA Astrophysics Data System (ADS)

    Berjozkina, S.; Sauhats, A.; Neimane, V.

    2013-10-01

    Introduction of new advanced electrical connections into a transmission grid reduces the capacity of existing overhead lines (OHLs). At the same time, designing & building of new OHLs and substations involves considerable technical, environmental and economical problems. The authors propose a concept of the multi-objective optimization for selection of transmission line routes, towers (their type, placement and geometry), of conductors, insulators, dampers, earthing and lightning protection systems, span lengths, etc.. The optimization is organized in five stages. At the first and second stages a search for optimum solutions is performed along with determination of the main impacting factors. The next two stages present a two-objective optimization based on Pareto's approach. At the last stage (exemplified by a case study), the probability of the restriction removal conditions is assessed, and preventive measures are identified. The presented approach uses a real line design and is intended for minimizing the total invested capital and maximizing the net present value. In the framework of this approach 20 alternatives have been elaborated, which can successfully be applied in the cases described in the paper. Elektropārvades tīklam rodas nepieciešamība pēc jauniem elektriskajiem pieslēgumiem, kas noved pie esošo gaisvadu līniju jaudas nepietiekamības. Viens no iespējamajiem pastāvošās problēmas risinājumiem ir jaunu gaisvadu līniju un apakšstacijas būvniecība. Gaisvadu līniju projektēšana ir saistīta ar ievērojamām tehniskām, vides un ekonomiskām problēmām. Darbā aprakstīta elektropārvades līnijas optimālās trases izvēles daudzkritēriju optimizācijas koncepcija, ieskaitot balstu tipa, balstu izvietojuma koordināšu, balstu ģeometrijas, vadu tipu un parametru, izolatoru tipu, vibroslāpētāju tipu, zibensaizsardzības un zemēšanas sistēmu, kā arī laidumu garumu izvēles optimizāciju. Optimizācijas uzdevums tiek organiz

  17. Assessing the Impact of a Community-Based Health and Nutrition Education on the Management of Diarrhea in an Urban District, Cairo, Egypt.

    PubMed

    Abdel-Aziz, Shaimaa B; Mowafy, Maha A; Galal, Yasmine S

    2016-01-01

    Diarrhea is considered as a major cause of mortality in children aged less than five years old. This pre/post interventional study was designed to assess maternal knowledge about diarrhea and implement a community-based health and nutrition education messages. The study was held in Al-Darb Al-Ahamar (ADAA) district, Cairo, Egypt and targeted a random sample of 600 mothers having at least one child under-five years old and complained of at least one previous attack of diarrhea. The study was conducted in three phases. The pre-intervention phase included a base line survey for the mothers and training activities for the community health workers (CHWs). Intervention phase included health and nutrition education sessions; performance evaluation for the CHWs during providing the message. In phase three, the mothers had no instructions for 3 months then the post- intervention interview and feedback sessions were conducted. Results showed that knowledge of mothers about diarrhea (etiological factors and preventive measures) had improved significantly after the intervention. During observation CHWs' scored 50% of the required tasks in education and communication skills. In the feedback sessions, all the mothers declared that nutrition education sessions were highly valuable, and asked for on-going support and training programs. The current study found that health and nutrition education sessions were successful in improving mothers' knowledge regarding preventive measures and management of diarrhea. CHWs are effective health education providers especially in household based intervention. Thus, health services should support community based interventions to reinforce mothers' knowledge and practices towards their sick children.

  18. Electric Machines with Non-Radially Mounted Rectangular Permanent Magnets / Elektriskās Mašīnas Ar Prizmatiskiem Neradiāli Novietotiem Pastāvīgajiem Magnētiem

    NASA Astrophysics Data System (ADS)

    Levin, N.; Pugachev, V.; Dirba, J.; Lavrinovicha, L.

    2013-04-01

    The authors analyze the advantages and disadvantages of brushless synchronous electric machines with radially and non-radially mounted rectangular permanent magnets. The results show that the proposed nonradial mounting of permanent magnets considered in the paper, in several cases (e.g. multi-pole brushless generators with tooth windings of the armature) allows achievement of the following advantages: better technology of manufacturing the electric machine owing to simple packing of the stator winding in the stator open slots, which also increases the copper slot fillfactor; reduction in the mass-and-size of permanent magnets at least twice; significantly lower cost of the electric machine; and, finally, its greater specific power. Darbā tiek analizētas priekšrocības un trūkumi sinhronām bezkontaktu mašīnām ar radiāli un neradiāli novietotiem prizmatiskiem pastāvīgajiem magnētiem. Parādīts, ka vairākos gadījumos, piemēram, daudzpolu bezkontaktu sinhronajos ģeneratoros ar zobu tinumiem, neradiāls pastāvīgo magnētu izvietojums nodrošina vairākas priekšrocības: uzlabojas mašīnas izgatavošanas tehnoloģija, jo statora atvērtajās rievās vieglāk novietot tinumus un iespējams sasniegt augstāku rievas aizpildījuma koeficientu; samazinās pastāvīgo magnētu masa un izmaksas; palielinās mašīnas īpatnēja jauda.

  19. Satellite Communications. SDPSK Modulator for Radiation Tolerant Satellite Modem / SDPSK Modulators Radiācijas Noturīgam Satelīta Modēmam

    NASA Astrophysics Data System (ADS)

    Skorodumovs, A.

    2013-02-01

    After a satellite has been launched, it is impossible to reprogram the hardware modulator. Therefore, a nanoRTU FPGA-based controller (AAC Microtec) in a modified modulation scheme may be programmed as a modem backend for softwaredefined radio (SDR) in the satellite communication system in order to adjust the balance of data rate vs. link reliability, enable coding or encryption system, change communication protocols, etc. For this purpose, a low-power radiation-tolerant reprogrammable satellite modem back-end has been realized for the satellite-to-Earth communication. This paper describes realization of a low data rate modulator based on a robust and reliable symmetric differential phase shift keying (SDPSK) modulation scheme combined with a raised cosine pulse shaping filter in nanoRTU, and presents results of its testing Kosmiskajās misijās iespējamas situācijas, kad rodas nepieciešamība pārkonfigurēt satelīta komunikācijas kanāla parametrus - izmantojamo modulācijas shēmu, pārraides protokolu, dekodēšanas algoritmu utt. Šajā rakstā izklāstīta SDPSK modulatora struktūra, kas optimizēta izmantošanai nanoRTU radiācijas noturīgajam aparatūras risinājumam, kā arī apskatītas modulatora darbības pārbaudes shēmas un izklāstīti iegūtie rezultāti

  20. Biorefinery Technologies for Biomass Conversion Into Chemicals and Fuels Towards Zero Emissions (Review) / Nulles Emisiju Princips Biomasas Konversijas Tehnoloģijās Aizstājot Fosilos Resursus (Pārskata Raksts)

    NASA Astrophysics Data System (ADS)

    Gravitis, J.; Abolins, J.

    2013-10-01

    Exhausting of world resources, increasing pollution, and climate change are compelling the shift of the world economy from continuous growth to a kind of economy based on integration of technologies into zero emissions production systems. Transition from non-renewable fossil resources to renewable resources provided by solar radiation and the current processes in biosphere is seen in the bio-refinery approach - replacing crude oil refineries by biomass refineries. Biotechnology and nano-technologies are getting accepted as important players along with conventional biomass refinery technologies. Systems design is a significant element in the integration of bio-refinery technologies in clusters. A number of case-studies, steam explosion auto-hydrolysis (SEA) in particular, are reviewed to demonstrate conversion of biomass into value-added chemicals and fuels. Analysis of energy flows is made as part of modelling the SEA processes, the eMergy (energy memory) approach and sustainability indices being applied to assess environmental impacts. Resursu izsīkums, vides piesārņojums un globāla mēroga klimatiskās izmaiņas ir civilizācijas izdzīvošanai būtiski faktori, kas virza pasaules ekonomikas pārmaiņas, atsakoties no nepārtrauktas izaugsmes idejas par labu tādai ekonomikai, kas balstās uz atjaunojošamies resursiem un dažādu tehnoloģiju integrācijemisiju principam atbilstošās ražošanas sistēmās. Saules radiācijas ierosinātajos planētas biosfērā notiekošajos procesos radīto organisko vielu pārstrādes kompleksi, kas operē ievērojot sabalansētu nulles emisiju principu, tiek uzlūkoti kā tās ekonomiskās (ražošanas) struktūras, kurām jānodrošina pāreja uz atjaunojošos resursu izmantošanu, aizstājot esošās fosilo resursu (naftas, ogļu) pārstrādes rūpnīcas. Līdzās jau apgūtajām biomasas rafinēšanas tehnoloģijām svarīga un pieaugoša loma ekonomiskās sistēmas resursu bāzes nomaiņā ir bio- un nanotehnolo

  1. Biorefinery Technologies for Biomass Conversion Into Chemicals and Fuels Towards Zero Emissions (Review) / Nulles Emisiju Princips Biomasas Konversijas Tehnoloģijās Aizstājot Fosilos Resursus (Pārskata Raksts)

    NASA Astrophysics Data System (ADS)

    Gravitis, J.; Abolins, J.

    2013-10-01

    Exhausting of world resources, increasing pollution, and climate change are compelling the shift of the world economy from continuous growth to a kind of economy based on integration of technologies into zero emissions production systems. Transition from non-renewable fossil resources to renewable resources provided by solar radiation and the current processes in biosphere is seen in the bio-refinery approach - replacing crude oil refineries by biomass refineries. Biotechnology and nano-technologies are getting accepted as important players along with conventional biomass refinery technologies. Systems design is a significant element in the integration of bio-refinery technologies in clusters. A number of case-studies, steam explosion auto-hydrolysis (SEA) in particular, are reviewed to demonstrate conversion of biomass into value-added chemicals and fuels. Analysis of energy flows is made as part of modelling the SEA processes, the eMergy (energy memory) approach and sustainability indices being applied to assess environmental impacts. Resursu izsīkums, vides piesārņojums un globāla mēroga klimatiskās izmaiņas ir civilizācijas izdzīvošanai būtiski faktori, kas virza pasaules ekonomikas pārmaiņas, atsakoties no nepārtrauktas izaugsmes idejas par labu tādai ekonomikai, kas balstās uz atjaunojošamies resursiem un dažādu tehnoloģiju integrācijemisiju principam atbilstošās ražošanas sistēmās. Saules radiācijas ierosinātajos planētas biosfērā notiekošajos procesos radīto organisko vielu pārstrādes kompleksi, kas operē ievērojot sabalansētu nulles emisiju principu, tiek uzlūkoti kā tās ekonomiskās (ražošanas) struktūras, kurām jānodrošina pāreja uz atjaunojošos resursu izmantošanu, aizstājot esošās fosilo resursu (naftas, ogļu) pārstrādes rūpnīcas. Līdzās jau apgūtajām biomasas rafinēšanas tehnoloģijām svarīga un pieaugoša loma ekonomiskās sistēmas resursu bāzes nomaiņā ir bio- un nanotehnolo

  2. Lapse time and frequency-dependent attenuation of coda waves in the Zagros continental collision zone in Southwestern Iran

    NASA Astrophysics Data System (ADS)

    Rahimi, H.; Hamzehloo, H.

    2008-06-01

    The coda Q, Qc, were estimated for the Zagros continental collision zone in southwestern Iran by analyzing the coda waves of 51 local earthquakes recorded on the three stations of the Iranian National Seismic Network (INSN) with magnitudes of between 3.1 and 4.9 recorded in the region during March and April 2006. Most of the analyzed events are foreshocks and aftershocks of the Darb-e-Astane earthquake which occurred on 31 March 2006 with a magnitude of 6.1 (IIEES). The earthquakes had an epicentral distance of between 120 and 200 km and a focal depth of about 18 km. The Qc values were computed at nine central frequencies of 1.5, 2.0, 3.0, 4.0, 6.0, 8.0, 12.0, 16.0 and 20.0 Hz through eight lapse time windows from 25 to 60 s starting at double the time of the primary S-wave from the origin time using the time-domain coda-decay method of a single backscattering model. In this study the collected data were compared between the events that occurred before and after the main event (foreshocks and aftershocks). The analysis showed a significant variation in the value of coda, Q, for the study region in different lapse times and frequencies. The variation of the quality factor, Qc, before and after the main event was estimated at different lapse time windows to observe its effect with depth. The estimated average frequency-dependent relation of Qc for foreshocks varies from Qc = (144 ± 24)f(0.42 ± 0.23) at 25 s to Qc = (85 ± 10)f(0.92 ± 0.11) at 60 s lapse window time length, respectively. For aftershocks, it varies from Qc = (121 ± 55)f(0.97 ± 0.26) at 25 s to Qc = (212 ± 59)f(0.82 ± 0.15) at 60 s. The averages of Qc in all stations and lapse times window are obtained as Qc = 99f0.84 and Qc = 178f0.86 for foreshocks and aftershocks, respectively. The Q frequency relationship for foreshocks is similar to that for the South Carolina, Koyna, western Anatolia and Aleutian earthquakes, whereas for aftershocks it is similar to the Kumaun, NW Himalaya and Parkfield

  3. High-Temperature Nuclear Reactors (Overview. Part 1) / Augstas Temperatūras Kodolreaktori (Pārskata raksts) 1. daļa

    NASA Astrophysics Data System (ADS)

    Ekmanis, J.; Tomsons, E.; Zeltiņš, N.

    2013-02-01

    At the Generation IV International Forum (GIF) of 2001 the measures were approved which are necessary for the development of future generation nuclear reactors (NRs). Six best high-temperature NR technologies were selected, with the main criteria being the safe and economically profitable operation, long-term use, protection against the employment of nuclear material for military purposes and terroristic attacks as well as technologies of fuel close cycle in order to increase the amount of fission material and decrease the amount of highly radioactive waste. In four of the technologies, apart from electricity production also hydrogen is obtained. Part 1 presents a generalized description of the high-temperature NRs, their comparative characteristics and history, with the stopped and operational HTNRs outlined. The properties of different type nuclear fuels are described in detail Ceturtās paaudzes kodolreaktoru starptautiskā forumā 2001.gadā nolēma par nepieciešamiem pasākumiem nākamās paaudzes kodolreaktoru izstrādei. Ir atlasītas sešas reaktoru tehnoloģijas, kuras lietderīgi turpmāk izstrādāt. Tās atlasītas ņemot vērā to drošu un ekonomiski izdevīgu darbību, ilgtspējīgu izmantošanu, aizsardzību pret materiālu izmantošanu militārām vajadzībām un teroristu uzbrukumiem, slēgtā degvielas cikla izmantošanu, lai palielinātu kodoldalīšanās materiālu daudzumu un samazinātu augstas aktivitātes atkritumu daudzumu, kurus būs jāapglabā. Četras no plānotām tehnoloģijām bez elektroenerģijas ieguves varēs ražot ūdeņradi. 1. daļā ietverts vispārīgs apraksts par augstas temperatūras kodolreaktoriem, to salīdzinājums pēc raksturlielumiem, pēc attīstības vēstures. Apskatīti gan apturētie, gan strādājošie reaktori, to kodoldegvielas

  4. Effect of dissimilatory iron and sulfate reduction on arsenic dynamics in the wetland rhizosphere and its bioaccumulation in plants

    NASA Astrophysics Data System (ADS)

    Jaffe, P. R.; Zhang, Z.; Moon, H. S.; Myneni, S.

    2015-12-01

    The mobility of arsenic in soils is linked to biogeochemical redox processes. The presence of wetland plants in riparian wetlands has a significant impact on the biogeochemical dynamics of the soil/sediment-redoxcline due to the release of root exudates and root turnover and oxygen transfer from the roots into the surrounding sediment. Micro-environmental redox conditions in the rhizosphere affect As, Fe, and S speciation as well as Fe(III) plaque deposition, which affects arsenic transport and uptake by plants. To investigate the dynamics of As coupled to S and Fe cycling in wetlands, mesocosms were operated in a greenhouse under various conditions (high and low Fe, high and low sulfate, with plant and without plants) for four months. Results show that the presence of plants, high Fe, and high SO42- levels enhanced As sequestration in these soils. We hypothesize that this compounding effect is because plants release biodegradable organic carbon, which is used by microorganism to reduce ferrihydrite and SO42- to generate FeS, FeS2, and/or orpiment (As2S3). Over the concentration range studied, As immobilization in soil and uptake by Scirpus actus was mainly controlled by SO42- rather than Fe levels. Under high sulfate levels, As immobilization in soil increased by 50% and As concentrations in plant roots increased by 97%, whereas no significant changes in plant As levels were seen for varying Fe concentrations. More than 80% of As was sequestrated in soils rather than plant uptake. Pore water As speciation analyses indicate that 20% more As(V) was reduced to As(III) under high sulfate as than low sulfate levels and that low Fe was more favorable to the As dissimilatory reduction. More dissimilatory arsenate-respiring bacteria (DARB) under high sulfate were confirmed by quantitative PCR. Arsenic distribution in plant leafs and roots after 30 days of exposure to As was analyzed via Synchrotron X-ray fluorescence analyses. The uptake of As by plants was distributed

  5. Wireless Inter-Crane Communication Method for Multi-Crane Scheduling in Maritime Container Terminals / Bezvadu Komunikācijas Tīkla Pielietojums Ostas Darba Efektivitātes Uzlabošanai

    NASA Astrophysics Data System (ADS)

    Černeckytė, M.; Kurmis, M.; Andziulis, A.; Gaigals, G.

    2013-10-01

    One of the main problems in the maritime container terminals is inefficient use of technical (quay cranes, yard cranes, mobile cranes) and human resources. All this affects negatively the scheduling of transportation and storage processes in the terminals. A new method proposed for the multicrane scheduling in maritime container terminals is based on the wireless inter-crane communication networks and dynamical localization of the mobile cranes using the Differential Global Positioning System (DGPS) technologies. It is shown that this method outperforms significantly the currently used owing to better time dependence of the crane traveling distance which allows for saving time resources. Industrija un zinātnes kopiena ir pievērsusi ļoti lielu uzmanību, lai jūras transporta sistēmās iekļautu mākslīgā intelekta komponentes, jo tās var sniegt dažādas priekšrocības. Viens no interesantākajiem tematiem šajā jomā ir konteineru transportēšanas un uzglabāšanas plānošanas metodes. Šajā darbā tiek piedāvāta jauna metode vairāku celtņa darba plānošanai jūras konteineru terminālos. Tā kā viena no galvenajām problēmām šajos terminālos ir neefektīva resursu - piestātņu celtņu, pacēlāju un autoceltņu izmantošana, metodes pamatā ir bezvadu datu pārraides tīkli komunikācijas starp celtņiem nodrošināšanai un celtņu dinamiska lokalizācija, izmantojot DGPS tehnoloģiju. Optimizēta iekārtu izmantošana nodrošina efektīvāku cilvēkresursu izmantošanu, kā arī uzlabo visu konteineru termināla procesu ātrdarbību.

  6. Reduction of Electric Breakdown Voltage in LC Switching Shutters / Elektriskās Caursites Sprieguma Samazināšana Šķidro Kristālu Šūnās

    NASA Astrophysics Data System (ADS)

    Mozolevskis, G.; Ozols, A.; Nitiss, E.; Linina, E.; Tokmakov, A.; Rutkis, M.

    2015-10-01

    ātes dēļ ir liela varbūtība šķidro kristālu (LC) šūnā novērot elektrisko caursiti, kuras laikā LC šūna tiek sabojāta. Šis ir viens no galvenajiem iemesliem, kāpēc šāda tipa ekrāni pagaidām vēl nav komerciāli plaši pieejami. Šajā darbā mēs skaidrojam rezultātus, kas iegūti, veicot LC šūnu caursites pētījumus. Elektrisko caursiti LC šūnā novēro brīdī, kad strāva tajā pārsniedz noteiktu sliekšņa vērtību. Strāvas stipruma sliekšņa vērtību nosaka šķidrā kristāla īpatnējā vadītspējā, kā arī punktu defekti LC šūnā, piemēram, putekļi, elektrodu raupjums, caurumi u.c. Strāvas stipruma ierobežošanai šūnā šajā darbā tika izmantotas dažādas metodes - buferslāņu iekļaušana, elektroda izlīdzinošā slāņa iekļaušana, kā arī elektroda sadalīšana ar lāzera ablācijas metodi. Tiek demonstrēts, ka elektrisko lauku, pie kura novēro caursiti šūnās, ir iespējams būtiski palielināt, šūnā iekļaujot elektriskos izolējošus buferslāņus un sadalot elektrodu.

  7. Ni-Al Protective Coating of Steel Electrodes in Dc Electrolysis for Hydrogen Production / Ni-Al Pārklājuma Ietekme Uz Tērauda Elektrodiem Līdzstrāvas Elektrolīzē Ūdeņraža Ražošanai

    NASA Astrophysics Data System (ADS)

    Aizpurietis, P.; Vanags, M.; Kleperis, J.; Bajars, G.

    2013-04-01

    Hydrogen can be a good alternative to fossil fuels under the conditions of world's crisis as an effective energy carrier derived from renewable resources. Among all the known methods of hydrogen production, water electrolysis gives the ecologically purest hydrogen, so it is of importance to maximize the efficiency of this process. The authors consider the influence of plasma sprayed Ni-Al protective coating of 316L steel anode-cathode electrodes in DC electrolysis. In a long-term (24 h) process the anode corrodes strongly, losing Cr and Ni ions which are transferred to the electrolyte, while only minor corrosion of the cathode occurs. At the same time, the composition of anode and cathode electrodes protected by Ni-Al coating changes only slightly during a prolonged electrolysis. As the voltammetry and Tafel plots evidence, the Ni-Al coating protects both the anode and cathode from the corrosion and reduces the potential of hydrogen evolution. The results obtained show that such a coating works best in the case of steel electrodes. Darbā pētīts, kā līdzstrāvas elektrolīzē tērauda 316L elektrodus (anods un katods) ietekmē ar plazmas izputināšanas metodi iegūts Ni-Al pārklājums. Tikko uznestam pārklājumam ir mikrostrukturēta virsma, kas kodināšanas laikā mainās, gan pēc reljefa, gan elementu sastāva. Veicot ilgstošu (24 stundas elektrolīzi), atrasts, ka tikai tērauda elektrods anoda lomā intensīvi korodē un zaudē hroma un niķeļa jonus, kas pāriet elektrolītā, turpretī katods mainās relatīvi maz. Pārklājums Ni-Al pēc uznešanas tiek kodināts karstā sārmā, kad tiek izšķīdināta daļa sastāvā esošo elementu (Al, Si, Cd), bet ilgstošas elektrolīzes laikā pārklājuma sastāvs mainās maz gan anodam, gan katodam. Elektrodu elektroķīmiskie raksturlielumi noteikti ar voltamperometrijas un Tāfeļa līkņu analīzes metodēm. Atrasts, ka Ni-Al pārklājums aizsargā gan anodu, gan katodu no korozijas un samazina

  8. Developed Design for Humeral Head Replacement Using 3D Surface Mapping

    NASA Astrophysics Data System (ADS)

    Salah, H. R.

    2014-12-01

    Assessment of dimensional and geometrical data on the humeral head replacement (HHR) objects is essential for solving the relevant designing problems in the physics of reverse engineering (RE). In this work, 2D-assessment for human humerus was performed using the computed tomography (CT) technique within the RE plan, after which the 2D images of humeral objects were converted into 3D images. The conversion was successful and indicated a clear difference in the 2D and 3D estimates of sizes and geometry of the humerus. The authors have analyzed and confirmed experimentally the statistical information on the relevant anatomical objects. The results of finite-element simulation of the compressive stresses affecting the geometry of 3D surface mapping were analyzed using SolidWorks software. For developing the biomechanical design of an HHR object suitable biomaterials were selected, and different metal-based biomaterials are discussed as applied at various loads. New methodology is presented for the size estimation of humeral head - both anatomical and artificial - in 3D-shape. A detailed interpretation is given for the results of CT D-measurements. Izmēru un ģeometrisko datu novērtējums, kas attiecas uz pleca kaula galviņas nomaiņas (PKGN) objektiem, nepieciešams, lai risinātu virkni reversīvās inženierijas (RI) problēmu. Šajā darbā cilvēka pleca kaula galviņas divdimensiju novērtējums tika veikts ar datortomogrāfijas palīdzību (RI) ietvaros, un pēc tam objekta divdimensiju attēlojums tika pārveidots trīsdimensiju. Pārveidojums bija sekmīgs, parādot pleca kaula galviņas izmēru un ģeometrijas atšķirības starp 2D un 3D novērtējumiem. Autori izanalizēja un eksperimentāli apstiprināja statistisko informāciju pēc dotā veida anatomiskiem objektiem. Saspiešanas sasprindzinājumi, kuri ietekmē trīsdimensiju virsmas attēlojuma ģeometriju, tika analizēti ar gala-elementu simulācijas metodi, lietojot programmu Solid

  9. Obtaining a Well-Aligned ZnO Nanotube Array Using the Hydrothermal Growth Method / Labi Sakārtotu Zno Nanocauruļu Kopu Iegūšana, Izmantojot Hidrotermālo Metodi

    NASA Astrophysics Data System (ADS)

    Krasovska, M.; Gerbreders, V.; Paskevics, V.; Ogurcovs, A.; Mihailova, I.

    2015-10-01

    Optimal growing parameters have been found using the hydrothermal method to obtain well-aligned vertical ZnO nanorod and nanotube arrays. The influence of different growing factors (such as temperature, growing solution concentration, method of obtaining seed layer and condition) on nanotube morphology and size is described in the paper. Well-structured ZnO nanotubes have been obtained by using a selfselective etching method with lowering temperatures of growth during the hydrothermal process. It is shown that the optical properties of the nanostructure arrays obtained are sensitive to the medium in which they are placed, which is why they can be used as sensors for pure substance detection and in different solutions for impurity determination. Dotajā darbā tika noteikti optimāli parametri labi sakārtotu ZnO nanocaurulīšu kopu iegūšanai, izmantojot hidrotermālo metodi ar temperatūras pazemināšanu, jeb t.s. selektīvu pa\\vskodināšanas metodi (self-selective etching), ir uzsvērtas šās metodes priekšrocības salīdzinājumā ar ķīmiskās kodināšanas metodi, kā arī tika aprakstīta dažādu augšanas faktora (tādu, ka darba šķīduma koncentrācija, augšanas temperatūra un laiks, iedīgļu slāņa iegūšanas veids un iegūšanas parametri) ietekme uz iegūtu nanostraktūra morfoloģiju. Tika konstatēts, ka noteicošu lomu ZnO nanocaurulīšu audzēšanas procesā spēlē iedīgļu slāņa graudu izmēri, kas savā staipā nosaka augošu nanostieņu izmērus un to tendenci pie pa\\vskodināšanas. Rentgenogrannnas parāda, ka iegūtām pie noteiktiem parametriem ZnO nanostruktūrām piemīt augsta kristāliskuma pakāpe un sakārtotība vertikālā virzienā. Optiskie mērījumi parāda, ka ZnO nanocauralītes ir jutīgas gan pret tīrām vielām (ūdens, spirts), gan pret dažādiem šķīdumiem, kas ļauj izmantot tos kā pie­jaukumu sensora. Salīdzinājumā ar ZnO nanostieņiem caurulīšu jūtība pieaug, jo pieaug nanostrakt

  10. Sail-Type Wind Turbine for Autonomous Power Supplay: Possible Use in Latvia

    NASA Astrophysics Data System (ADS)

    Sakipova, S.; Jakovics, A.

    2014-12-01

    Under the conditions of continuous increase in the energy consumption, sharply rising prices of basic energy products (gas, oil, coal), deterioration of environment, etc., it is of vital importance to develop methods and techniques for heat and power generation from renewables. The paper considers the possibility to use a sail-type wind turbine for autonomous power supply in Latvia, taking into account its climatic conditions. The authors discuss the problems of developing a turbine of the type that would operate efficiently at low winds, being primarily designed to supply power to small buildings and farms distant from centralized electricity networks. The authors consider aerodynamic characteristics of such a turbine and the dependence of the thrust moment of its pilot model on the airflow rate at different angles of attack. The pilot model with a changeable blade shape has been tested and shows a good performance. Darbs veltīts vienam no atjaunojamo enerģiju veidiem - vēja enerģijai, analizētas tās izmantošanas iespējas. Vispirms īsi raksturota vēja enerģijas izmantošana pasaulē, kā arī vērtētas izmantošanas perspektīvas no inženiertehniskā un klimatisko apstākļu viedokļa. Turpinājumā raksturota situācija Latvijā, t. sk., arī vēja potenciāla pieejamība dažādos reģionos, kā arī vēja enerģijas izmantošanas efektivitāti raksturojošie lielumi. Konstatējot problēmu, rast vēja turbīnu risinājumus Latvijas apstākļiem ar maziem vidējiem vēja ātrumiem, izveidots buras tipa turbīnas modelis. Šī modeļa raksturlielumu izpēte veikta vēja tunelī Karagandas universitātē, konstatējot relatīvi labus efektivitātes rādītājus tiešai un pretējai vēja plūsmai. Izmantojot mērījumu rezultātus, ierosināti sistēmas uzlabojumi, kurus plānots pētīt turpmāk. Šādas sistēmas potenciāli var rast lietojumu tur, kur nepieciešami autonomi enerģijas avoti.

  11. Fused Deposition Modelling as Rapid Prototyping for Structural Material Improvement: Analytical Solution / Ātrās Prototipēšanas Ar Kausēšanas Metodi Strukturālā Uzlabojuma Analītisks Risinājums

    NASA Astrophysics Data System (ADS)

    Brensons, I.; Polukoshko, S.

    2013-10-01

    Fused deposition modelling (FDM) is one of the most effective rapid prototyping (RP) techniques due to its low cost, available materials and versatility. In FDM, a part of material (usually plastic) is made by heating this material to the molten state, and from the melt it is extruded through a nozzle and deposited on a surface. In the article, an alternative RP method is considered for improvement of the mechanical properties of a rapid prototype. The authors propose an analytical solution which allows for achievement of this purpose via advanced technologies. The base materials applied in RP technology can be combined with liquid resin which solidifies after a definite time. This makes it possible to create a channel through the prototype and fill it with another material having better mechanical properties. The optimal channel sizes can be chosen in order to raise the strength of material parts. Darbā tiek apskatīts ātrās prototipēšanas veids, kura pamatā ir detaļas veidošana, izmantojot kausētu materiālu parasti plastmasu. Šī detaļu veidošanas metode ir kļuvusi par vienu no visizplatītākajām tās zemo izmaksu, pieejamo materiālu un daudzpusības dēļ. Šī raksta mērķis ir izpētīt alternatīvu veidu, kā uzlabot prototipu mehāniskās īpašības, tādējādi palielinot printētu detaļu izmantošanu kā gala produktu. Raksts piedāvā analītisku risinājumu, kā uzlabot ātro prototipu mehāniskās īpašības, uzlabojot tehnoloģiskos procesus, kas iesaistīti detaļu izgatavošanā. Darba pamatā tiek izmantota 3D printēšanas tehnoloģijas iespēja veidot iekšējus kanālus bez ģeometriskiem ierobežojumiem, kā rezultātā ir iespējams izveidot iekšēju kanālu shēmu, ko pēc tam piepilda ar citu materiālu, kam ir labākas mehāniskās īpašības kā pamata materiālam. Pildīšanai izmantotais materiāls ir epoksīda sveķi, kas pieļauj vieglu iepildīšanu šķidrā fāzē, un sniedz labas mehāniskās īpašības p

  12. Development of Solar Powered Feeding Scheme for Wireless Sensor Networks in low Solar Density Conditions / Bezvadu Sensoru Tīklu Elektroapgādes Sistēmas Izstrāde, Kas Izmanto Saules Paneļus Un Darbojas Pazeminātas Saules Radiācijas Apstākļos

    NASA Astrophysics Data System (ADS)

    Kondratjevs, K.; Zabasta, A.; Selmanovs-Pless, V.

    2015-08-01

    kontekstā ar reģionālajiem apstākļiem un aprēķināt darba režīmus bezvadu tīkla komponentēm vai pieņemt lēmumus par to funkcionalitātes pielāgošanu. Izstrādātais vadības modulis sastāv no saules paneļa fotoelementu moduļa, uzglabāšanas risinājuma (litija vai līdzvērtīgas baterijas) un elektroapgādes pārvaldības moduļa. Pētījuma novitāte ir elektroapgādes pārvaldības modulis, kas nodrošina stabilu un nepārtrauktu elektronisko iekārto darbību dažādos barošanas režīmos, dažādās situācijās, vienlaikus nodrošinot enerģijas saglabāšanu un moduļa sastāvdaļu ilgtspēju. Izstrādātais risinājums nodrošina nepārtrauktu 5V barošanu elektronikas shēmām bez strāvas pārtraukuma, kad notiek komutācija starp barošanas avotiem un enerģijas plūsmām dažādos virzienos. Elektroapgādes pārvaldības modulis nodrošina stabilu spriegumu mainīgos saules radiācijas apstākļos.

  13. Determination of Two-Liquid Mixture Composition by Assessing Dielectric Parameters 1. Precise Measuring System / Divu Šķidrumu Maisījuma Sastāva Noteikšana, Izvērtējot to Dielektriskos Parametrus 1. Precīza Mērīšanas Sistēma

    NASA Astrophysics Data System (ADS)

    Vilitis, O.; Shipkovs, P.; Merkulovs, D.

    2013-08-01

    ,01%. Šajā darbā piedāvātajā jaunajā mērīšanas sistēmas struktūras risinājumā iekļautas divas tiešas signālu digitālās sintēzes mikrosistēmas, kas ar augstu precizitāti ģenerē mērīšanai nepieciešamās formas, fāzes un amplitūdas signālus ar 100,000 kHz frekvenci un tiek vadītas no mikrokontrolera. Mērīšanas sistēmā izmantota mērsignālu sinhronizētās detektēšanas tehnika. Izstrādātās sistēmas konigurācija, mērīšanas režīma uzstādījums un vadība automātiski praktiski izslēdz virkni mērīšanas signālu parazītisko fāzes nobīžu un fāzes uzstādījumu kļūdas. Izstrādātā mērīšanas sistēma ērti piemērojama vispārējai izmantošanai kapacitātes vai impedances mērierīcēs. Samērā nelielā prognozējamā mērīšanas sistēmas pašizmaksa un kompaktā, portatīvā konstrukcija, kā arī iepriekš minētās priekšrocības paplašina sistēmas lietojumu ne tikai etanola koncentrācijas mērīanai bioetanola ražošanas procesā, bet šī sistēma var tikt izmantota arī eļļas, benzīna un citu degvielu testēšanai, ķīmiskajā, farmācijas un pārtikas industrijā, mikrobioloģijā un medicīnā, lai noteiktu glikozes, antigēnu, antivielu, proteīna, DNS fragmentu un citu vielu saturu šķīdumos u.c.

  14. Greenhouse Gas Emission Reduction Due to Improvement of Biodegradable Waste Management System

    NASA Astrophysics Data System (ADS)

    Bendere, R.; Teibe, I.; Arina, D.; Lapsa, J.

    2014-12-01

    ārdāmo atkritumu apsaimniekošanas statistikas datu novērtējums atbilstoši likumdošanas prasībām. Izmantojot matemātisko modelēšanas programmu WAMPS, analizēti trīs dažādi bioloģisko noārdāmo atkritumu apsaimniekošanas scenāriji, kuriem veikts vides ietekmes novērtējums, kas izteikts klimata pārmaiņu potenciālā - tonnas CO2 ekv. Darbā secināts, ka lielākais siltumnīcefektu (SEG) avots atkritumu apsaimniekošanas ir atkritumu poligoni (Bāzes scenārijs), ko galvenokārt ietekmē CH4 rašanās, organiskajiem atkritumiem sadaloties anaerobos apstākļos. Būtisku pozitīvo efektu SEG emisiju samazināšanā dod atkritumu pārstrāde otrreizējās izejvielās un sadedzināšana cementa ražotnē, kas ļauj samazināt dabīgo izejmateriālu un fosilo enerģijas resursu patēriņu. Attīstot pārtikas atkritumu pārstrādi biogāzē, lietderīgi veidot alternatīvās vai izmantot esošās sistēmas, kas nodrošina iegūtās enerģijas un digestāta patēriņu, t.i lauksaimniecība, transports vai komunālie pakalpojumi. Lai no zaļajiem dārza atkritumiem iegūtu augstvērtīgu kompostu, valstī jārada tam nepieciešami likumdošanas un ekonomiskie instrumenti, kas veicina komposta tirgus attīstību.

  15. Development and Experimental Study of Phantoms for Mapping Skin Chromophores

    NASA Astrophysics Data System (ADS)

    Silapetere, A.; Spigulis, J.; Saknite, I.

    2014-06-01

    Skin chromophore phantoms are widely used for better understanding of the light interaction with tissue and for calibration of skin diagnostic imaging techniques. In this work, different phantoms were examined and compared in order to find biologically equivalent substances that are the most promising for this purpose. For mimicking the skin medium and layered structure, a fibrin matrix with epidermal and dermal cell inclusion was used. Synthesized bilirubin, red blood cells and nigrosin were taken as absorbers. For spectral analysis of the developed phantoms a computer-aided multispectral imaging system Nuance 2.4 (Cambridge Research & Instrumentation, Inc., USA) was used. In this study, skin phantoms were created using such substances as bilirubin, melanin, haemoglobin and nigrosin Mūsdienās multispektrālās attēlošanas iekārtas izmanto ādas parametru un fizioloģisko procesu aprakstīšanai gan pētniecības, gan diagnostikas nolūkiem. Iekārtu darbības uzlabošanai ir nepieciešams labāk saprast gaismas mijiedarbību ar audiem, kā arī veikt šo iekārtu kalibrēšanu ar ādas maketu. Redzamā un tuvā infrasarkanā optiskā diapazona spektroskopijā ir svarīgi ādas maketi, kas simulē audu slāņaino struktūru un ķīmiskās īpašības, kā arī maketi, kas ir bioloģiski līdzvērtīgi. Šajā pētījumā tika izveidots ādas makets no bioloģiskām un ķīmiski sintezētām struktūrām. Ādas maketa izveidei tika izmantota fibrīna matrica ar dermālo un epidermālo šūnu piejaukumu, lai imitētu ādas slāņaino struktūru. Fibrīna matrica tiek veidota no 0,47 ml asins plazmas, 0,4 ml fizioloģiskā šķīduma, 0,8 μl treneksāmskābes un 89,4 μl kalcija glukanāta. Izveidoto matricu ievieto šūnu inkubatorā, lai tā polimerizētos. Nākošais slānis tiek veidots ar dermālo šūnu piejaukumu (180-270 šūnas), un pēdējais fibrīna matriksa slānis tiek veidots ar epidermālo šūnu piejaukumu (270 šūnas) un šūnu aug