Identification and Analysis of Partial Shading Breakdown Sites in CuIn xGa (1-x)Se 2 Modules

DOE PAGES

Palmiotti, Elizabeth; Johnston, Steven; Gerber, Andreas; ...

2017-12-20

In this paper, CuIn xGa (1-x) (CIGS) mini-modules are stressed under reverse bias, resembling partial shading conditions, to predict and characterize where failures occur. Partial shading can cause permanent damage in the form of 'wormlike' defects on thin-film modules due to thermal runaway. This results in module-scale power losses. We have used dark lock-in thermography (DLIT) to spatially observe localized heating when reverse-bias breakdown occurs on various CIGS mini-modules. For better understanding of how and where these defects originated and propagated, we have developed techniques where the current is limited during reverse-bias stressing. This allows for DLIT-based detection and detailedmore » studying of the region where breakdown is initiated before thermal runaway leads to permanent damage. Statistics of breakdown sites using current-limited conditions has allowed for reasonable identification of the as-grown defects where permanent breakdown will likely originate. Scanning electron microscope results and wormlike defect analysis show that breakdown originates in defects such as small pits, craters, or cracks in the CIGS layer, and the wormlike defects propagate near the top CIGS interface.« less

Tooth shade measurements under standard and nonstandard illumination and their agreement with skin color.

PubMed

Al-Dwairi, Ziad; Shaweesh, Ashraf; Kamkarfar, Sohrab; Kamkarfar, Shahrzad; Borzabadi-Farahani, Ali; Lynch, Edward

2014-01-01

The purpose of this study was to examine the relationship between skin color (shade) and tooth shade under standard and nonstandard illumination sources. Four hundred Jordanian participants (200 males, 200 females, 20 to 50 years of age) were studied. Skin colors were assessed and categorized using the L'Oreal and Revlon foundation shade guides (light, medium, dark). The Vita Pan Classical Shade Guide (VPCSG; Vident) and digital Vita EasyShade Intraoral Dental Spectrophotometer (VESIDS; Vident) were used to select shades in the middle thirds of maxillary central incisors; tooth shades were classified into four categories (highest, high, medium, low). Significant gender differences were observed for skin colors (P = .000) and tooth shade guide systems (P = .001 and .050 for VPCSG and VESIDS, respectively). The observed agreement was 100% and 93% for skin and tooth shade guides, respectively. The corresponding kappa statistic values were 1.00 and 0.79, respectively (substantial agreement, P < .001). The observed agreement between skin color and tooth shades (VPCSG and VESIDS) was approximately 50%. The digital tooth shade guide system can be a satisfactory substitute for classical tooth shade guides and clinical shade matching. There was only moderate agreement between skin color and tooth shade.

Ozonation of exhausted dark shade reactive dye bath for reuse.

PubMed

Sundrarajan, M; Vishnu, G; Joseph, Kurian

2006-10-01

Exhausted reactive dye bath of dark shades were collected from cotton knit wear dyeing units in Tirupur. Ozonation was conducted in a column reactor system fed with ozone at the rate of 0.16 g/min to assess its efficiency in reducing the color, chemical oxygen demand and total organic carbon. The potential of the decolorized dye bath for its repeated reuse was also analyzed. The results from the reusability studies indicate that the dyeing quality was not affected by the reuse of decolorized dye bath for two successive cycles. Complete decolorization of the effluent was achieved in 60 minutes contact time at an ozone consumption of 183 mg/L for Red, 175 for Navy Blue and 192 for Green shades respectively. The corresponding COD removal was 60%, 54% and 63% for the three shades while TOC removal efficiency was 59%, 55% and 62% respectively. It is concluded that ozonation is efficient in decolorization of exhausted dye bath effluents containing conventional reactive dyes. However, the corresponding removal of COD from the textile effluent was not significant.

Dark Energy Survey finds more celestial neighbors | News

Science.gov Websites

Energy Survey finds more celestial neighbors August 17, 2015 icon icon icon New dwarf galaxy candidates could mean our sky is more crowded than we thought The Dark Energy Survey has now mapped one-eighth of Survey Collaboration The Dark Energy Survey has now mapped one-eighth of the full sky (red shaded region

NICMOS status and plans

NASA Technical Reports Server (NTRS)

Thompson, Rodger I.

1997-01-01

Near Infrared Camera and Multi-Object Spectrometer (NICMOS) has been in orbit for about 8 months. This is a report on its current status and future plans. Also included are some comments on particular aspects of data analysis concerning dark subtraction, shading, and removal of cosmic rays. At present NICMOS provides excellent images of high scientific content. Most of the observations utilize cameras 1 and 2 which are in excellent focus. Camera 3 is not yet within the range of the focus adjustment mechanism, but its current images are still quite excellent. In this paper we will present the status of various aspects of the NICMOS instrument.

The Beauty of the Beasts in Chalk Pastels

ERIC Educational Resources Information Center

Skophammer, Karen

2010-01-01

In this article, the author describes how her seventh-grade art students captured an image of a stuffed animal in the "whole-to-part" drawing technique using chalk pastels. Shading with chalk pastels can give a gradual change in value from dark to light. The shading and color changes the mood of the original drawing, and adds texture, too. Chalk…

Crassulacean acid metabolism in the shade. Studies on an epiphytic fern, Pyrrosia longifolia, and other rainforest species from Australia.

PubMed

Winter, K; Osmond, C B; Hubick, K T

1986-01-01

Crassulacean acid metabolism (CAM) was studied in a tropical epiphytic fern, Pyrrosia longifolia, from a fully sun-exposed and from a very shaded site in Northern Queensland, Australia. Measurements of instantaneous net CO 2 exchange showed carbon gain via CO 2 dark fixation with some net CO 2 uptake also occuring during late afternoon, in both sun and shade fronds. Maximum rates of net CO 2 uptake and the nocturnal increase in titratable acidity were lower in shade than in sun fronds. δ 13 C values of sun and shade fronds were not significantly different, and ranged between-14 and-15‰ suggesting that, in the long term, carbon gain was mainly via CO 2 dark fixation. Sun fronds had a higher light compensation point of photosynthesis than shade fronds but the same quantum yield. Yet there was no acclimation of photosynthetic O 2 evolution, (measured at 5% CO 2 ) in sun and shade fronds and photosynthesis saturated at between 200 and 400 μmol quanta m -2 s -1 . Use of higher light intensities for photosynthesis of sun fronds was probably precluded by low nutrient availability. Total nitrogen was less than 1% of dry weight in fully expanded sun and shade fronds. Exposure of shade fronds to full sunlight for 6 h led to a 60% decline in the quantum yield of photosynthesis and to a decline in variable fluorescence measured at room temperature. Photoinhibition by high light was also observed in Hoya nicholsoniae, a rainforest climber growing in deep shade. This species also exhibited CAM as demonstrated by nocturnal net CO 2 uptake, nocturnal acidification and a δ 13 C value of-14‰. Photosynthetic O 2 evolution in this species was saturated at 2.5% of full sunlight. Two species of Dendrobium (Orchidaceae) from sun-exposed sites, one species exhibiting CAM and the other one exhibiting net CO 2 uptake exclusively during daytime via conventional C 3 photosynthesis, showed similar light response curves and the same quantum yield for photosynthetic O 2 evolution.

Dying piece by piece: carbohydrate dynamics in aspen (Populus tremuloides) seedlings under severe carbon stress.

PubMed

Wiley, Erin; Hoch, Günter; Landhäusser, Simon M

2017-11-02

Carbon starvation as a mechanism of tree mortality is poorly understood. We exposed seedlings of aspen (Populus tremuloides) to complete darkness at 20 or 28 °C to identify minimum non-structural carbohydrate (NSC) concentrations at which trees die and to see if these levels vary between organs or with environmental conditions. We also first grew seedlings under different shade levels to determine if size affects survival time under darkness due to changes in initial NSC concentration and pool size and/or respiration rates. Darkness treatments caused a gradual dieback of tissues. Even after half the stem had died, substantial starch reserves were still present in the roots (1.3-3% dry weight), indicating limitations to carbohydrate remobilization and/or transport during starvation in the absence of water stress. Survival time decreased with increased temperature and with increasing initial shade level, which was associated with smaller biomass, higher respiration rates, and initially smaller NSC pool size. Dead tissues generally contained no starch, but sugar concentrations were substantially above zero and differed between organs (~2% in stems up to ~7.5% in leaves) and, at times, between temperature treatments and initial, pre-darkness shade treatments. Minimum root NSC concentrations were difficult to determine because dead roots quickly began to decompose, but we identify 5-6% sugar as a potential threshold for living roots. This variability may complicate efforts to identify critical NSC thresholds below which trees starve. © Society for Experimental Biology 2017.

Adaptive Criterion Setting in Perceptual Decision Making

ERIC Educational Resources Information Center

Stuttgen, Maik C.; Yildiz, Ali; Gunturkun, Onur

2011-01-01

Pigeons responded in a perceptual categorization task with six different stimuli (shades of gray), three of which were to be classified as "light" or "dark", respectively. Reinforcement probability for correct responses was varied from 0.2 to 0.6 across blocks of sessions and was unequal for correct light and dark responses. Introduction of a new…

Evaluation of the Efficacy and Color Stability of Two Different At-Home Bleaching Systems on Teeth of Different Shades: A Randomized Controlled Clinical Trial.

PubMed

Aka, Betül; Celik, Esra Uzer

2017-09-01

This randomized controlled clinical trial compared the bleaching efficacy of two different at-home bleaching systems on teeth of different shades and their color stability after a 6-month follow-up. Ninety-two patients (777 teeth) were randomly divided into three groups: (a) negative control, (b) patients treated with a custom-made tray containing 10% carbamide peroxide (10% CP/PF) (Opalescence PF), and (c) patients treated with a pre-loaded tray containing 6% hydrogen peroxide (6% HP/Go) (Opalescence Go). Teeth in all groups were divided into three sub-groups according to the VITA Classic Shade Guide: light (A1-C1), medium dark (C2-B3), and dark (A3.5-C4). Bleaching systems were performed in accordance with manufacturers' instructions for 14 days. The color values were measured at the baseline, 10 days and 14 days of bleaching, 2 weeks, and 6 months after bleaching. Three-way ANOVA and Mann-Whitney U tests were used for statistical analysis (α = 0.05). Irrespective of original shade, both bleaching groups showed significantly higher ΔE* values than the control groups, and the ΔE* values were significantly higher in the 10% CP/PF groups than those in the 6% HP/Go groups (p < 0.05). In both bleaching systems, the dark teeth showed higher ΔE* values than the light teeth (p < 0.05). The ΔE* values decreased significantly only in the 10% CP/PF groups after 6 months (p < 0.05). Both bleaching agents produced a bleaching effect, but 10% CP/PF was more effective. A pre-loaded tray system may be used for dental bleaching, but it is still less effective than conventional a 10% carbamide peroxide system, irrespective of the initial shade. (J Esthet Restor Dent 29:325-338, 2017). © 2017 Wiley Periodicals, Inc.

The impact of translucent fabric shades and control strategies on energy savings and visual quality

NASA Astrophysics Data System (ADS)

Wankanapon, Pimonmart

Translucent fabric shades provide opportunities for building occupants to control sunlight penetration for heat reduction, thermal comfort, and visual quality. Regulating shades affects building energy and can potentially reduce the size of mechanical cooling systems. Shades are not normally included in energy model studies during the design process, even though shades potential impact energy use. This is because the occupants normally leave shades closed a large fraction of the time, but models are generally performed with no shades. Automatic shade control is now available, so it is necessary to understand the impact of shades on visual quality and their energy saving potential in order to optimize their overall performance. There are very limited studies that have address shades and their integrated performance on energy consumption and visual quality. Most of these do not reflected modern shade types and their application. The goals of this study are: First, to determine the impact of shades on total, heating, cooling and lighting energy savings with different design and operation parameters. Second, to study and develop different automatic shade control strategies to promote and optimize energy savings and visual quality. A simulation-based approach using EnergyPlus in a parametric study provide better understanding energy savings under different shade conditions. The parametric runs addressed various building parameters such as geometry, orientation, site climate, glazing/shade properties, and shade control strategies with integrated lighting control. The impact of shades was determined for total building and space heating, cooling and lighting energy savings. The effect of shades on visual quality was studied using EnergyPlus, AGI32 and DAYSIM for several indices such as daylight glare index (DGI), work plane illuminance, luminance ratios and view. Different shade control strategies and integrated lighting control were considered with two translucent fabric shade colors. The results clearly show the benefit of automatic shade control strategies with integrated lighting control over a condition when shades are closed all day. The main contributor to the total energy savings is from lighting energy savings, followed by cooling energy savings. Shades provide greater benefit in a hot climate and in a moderate climate than in a cold climate. Different control strategies provide savings in the range of 7-35% for annual total space energy with higher savings with light colored shades. Control strategies of shades should be selected and optimized based on climate, orientation, window area, and window/shade properties. High performance glazings, when equipped with shades, show lower energy savings when compared to standard glazings. High transmittance/reflectance shades, such as white shades, perform better than dark shades in most of the cases due to higher lighting energy savings obtained with the automatic electric lighting control and the resulting cooling energy savings from rejection of some solar energy and a reduction in the heat from lights. A South orientation showed the least benefit of automatic control of shades when compare to other orientations due to the large fraction of time shades are required to provide visual comfort. Under automatic shade control, energy savings are higher the more often the shades can be raised. The different automatic control strategies present tradeoffs between energy savings and comfort. With regard to visual quality, daylight quality assessments on view, glare, luminance ratios, and UDI can be used to assess shade control strategies. Automatic shade control can increase the number of view hours while controlling sunlight penetration. With automatic shade control, more daylight hours can be provided within the beneficial range of 100-2000 lux compared to shades that are closed all day. For a person facing the window, discomfort glare is likely to increase the more often the shades are raised. Keeping the shades down ensures an acceptable glare condition, but limits energy savings. Luminance ratios are another metric that can be used to assess shade performance. With white shades, the luminance ratios between the task and proximate surfaces are improved. Dark shades help improve the luminance ratios between the task and distant surfaces. When the shades are left open, even with no direct sunlight in the space, task to window luminance ratios will often exceed 1:10.

[In vivo model to evaluate the accuracy of complete-tooth spectrophotometer for dental clinics].

PubMed

Liu, Feng; Yang, Jian; Xu, Tong-Kai; Xu, Ming-Ming; Ma, Yu

2011-02-01

To test ΔE between measured value and right value from the Crystaleye complete-tooth spectrophotometer, and to evaluate the accuracy rate of the spectrophotometer. Twenty prosthodontists participated in the study. Each of them used Vita 3D-Master shadeguide to do the shade matching, and used Crystaleye complete-tooth spectrophotometer (before and after the test training) tested the middle of eight fixed tabs from shadeguide in the dark box. The results of shade matching and spectrophotometer were recorded. The accuracy rate of shade matching and the spectrophotometer before and after training were calculated. The average accuracy rate of shade matching was 49%. The average accuracy rate of the spectrophotometer before and after training was 83% and 99%. The accuracy of the spectrophotometer was significant higher than that in shade matching, and training can improve the accuracy rate.

Estimating Canopy Dark Respiration for Crop Models

NASA Technical Reports Server (NTRS)

Monje Mejia, Oscar Alberto

2014-01-01

Crop production is obtained from accurate estimates of daily carbon gain.Canopy gross photosynthesis (Pgross) can be estimated from biochemical models of photosynthesis using sun and shaded leaf portions and the amount of intercepted photosyntheticallyactive radiation (PAR).In turn, canopy daily net carbon gain can be estimated from canopy daily gross photosynthesis when canopy dark respiration (Rd) is known.

Mapping Geological Units on Mars by Analyzing the Spectral Properties of the Surface from the Mars-Express High Resolution Stereo Camera (HRSC)

NASA Astrophysics Data System (ADS)

Combe, J.; Adams, J. B.; McCord, T. B.

2006-12-01

Geological units at the surface of Mars can be investigated through the analysis of spatial changes of both its composition and its superficial structural properties. The color images provided by the High Resolution Stereo Camera (HRSC) are a multispectral dataset with an unprecedented high spatial resolution. We focused this study on the western chasmas of Valles Marineris with the neighboring plateau. Using the four-wavelength spectra of HRSC, the two types of surface color units (bright red and dark bluish material) plus a shade/shadow component can explain most of the variations [1]. An objective is to provide maps of the relative abundances that are independent of shade [2]. The spectral shape of the shade spectrum is calculated from the data. Then, Spectral Mixture Analysis of the two main materials and shade is performed. The shade gives us indications about variations in the surface roughness in the context of the mixtures of spectral/mineralogical materials. For mapping the different geological units at the surface at high spatial resolution, a correspondence between the color and the mineralogy is needed, aided by direct and more precise identifications of the composition of Mars. The joint analysis of HRSC and results from the OMEGA imaging spectrometer makes the most of their respective abilities [1]. Ferric oxides are present in bright red materials both in the chasmas and on the plateau [1] and they are often mixed with dark materials identified as basalts containing pyroxenes [4]. In Valles Marineris, salt deposits (bright) have been reported by using OMEGA [3], along with ferric oxides [4, 5] that appear relatively dark. The detailed spatial distribution of these materials is a key to understand the geology. Examples will be presented. [1] McCord T. B., et al. 2006, JGR, submitted. [2] Adams J. B. And Gillespie A. R., 2006, Cambridge University Press, 362 pp. [3] Le Mouelic S. et al., 2006, LPSC #1409. [4] Gendrin et al. (2005), LPSC #1858. [5] Gendrin A. et al., 2005, Science, 307, 1587-1591. [6] Le Deit et al., 2006, LPSC #2115.

The first batteryless, solar-powered cardiac pacemaker.

PubMed

Haeberlin, Andreas; Zurbuchen, Adrian; Walpen, Sébastien; Schaerer, Jakob; Niederhauser, Thomas; Huber, Christoph; Tanner, Hildegard; Servatius, Helge; Seiler, Jens; Haeberlin, Heinrich; Fuhrer, Juerg; Vogel, Rolf

2015-06-01

Contemporary pacemakers (PMs) are powered by primary batteries with a limited energy-storing capacity. PM replacements because of battery depletion are common and unpleasant and bear the risk of complications. Batteryless PMs that harvest energy inside the body may overcome these limitations. The goal of this study was to develop a batteryless PM powered by a solar module that converts transcutaneous light into electrical energy. Ex vivo measurements were performed with solar modules placed under pig skin flaps exposed to different irradiation scenarios (direct sunlight, shade outdoors, and indoors). Subsequently, 2 sunlight-powered PMs featuring a 4.6-cm(2) solar module were implanted in vivo in a pig. One prototype, equipped with an energy buffer, was run in darkness for several weeks to simulate a worst-case scenario. Ex vivo, median output power of the solar module was 1963 μW/cm(2) (interquartile range [IQR] 1940-2107 μW/cm(2)) under direct sunlight exposure outdoors, 206 μW/cm(2) (IQR 194-233 μW/cm(2)) in shade outdoors, and 4 μW/cm(2) (IQR 3.6-4.3 μW/cm(2)) indoors (current PMs use approximately 10-20 μW). Median skin flap thickness was 4.8 mm. In vivo, prolonged SOO pacing was performed even with short irradiation periods. Our PM was able to pace continuously at a rate of 125 bpm (3.7 V at 0.6 ms) for 1½ months in darkness. Tomorrow's PMs might be batteryless and powered by sunlight. Because of the good skin penetrance of infrared light, a significant amount of energy can be harvested by a subcutaneous solar module even indoors. The use of an energy buffer allows periods of darkness to be overcome. Copyright © 2015 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Optimizing countershading camouflage.

PubMed

Cuthill, Innes C; Sanghera, N Simon; Penacchio, Olivier; Lovell, Paul George; Ruxton, Graeme D; Harris, Julie M

2016-11-15

Countershading, the widespread tendency of animals to be darker on the side that receives strongest illumination, has classically been explained as an adaptation for camouflage: obliterating cues to 3D shape and enhancing background matching. However, there have only been two quantitative tests of whether the patterns observed in different species match the optimal shading to obliterate 3D cues, and no tests of whether optimal countershading actually improves concealment or survival. We use a mathematical model of the light field to predict the optimal countershading for concealment that is specific to the light environment and then test this prediction with correspondingly patterned model "caterpillars" exposed to avian predation in the field. We show that the optimal countershading is strongly illumination-dependent. A relatively sharp transition in surface patterning from dark to light is only optimal under direct solar illumination; if there is diffuse illumination from cloudy skies or shade, the pattern provides no advantage over homogeneous background-matching coloration. Conversely, a smoother gradation between dark and light is optimal under cloudy skies or shade. The demonstration of these illumination-dependent effects of different countershading patterns on predation risk strongly supports the comparative evidence showing that the type of countershading varies with light environment.

NASA Spacecraft Images Continued Thailand Flooding

NASA Image and Video Library

2011-10-28

On Oct. 25, 2011, the Chao Phraya River was in flood stage as NASA Terra spacecraft imaged flooded agricultural fields and villages depicted here in dark blue, and the sediment-laden water in shades of tan.

Modeling shade tree use by beef cattle as a function of black globe temperature and time of day

NASA Astrophysics Data System (ADS)

Foust, Amanda M.; Headlee, William L.

2017-12-01

Increasing temperatures associated with global climate change threaten to disrupt agricultural systems such as beef production, yet relatively little is known about the use of natural tree shade to mitigate the negative effects of heat stress on beef cattle. In this study, we evaluated how temperature and time of day influenced the utilization of tree shade in relation to coloration, orientation, and behavior of beef cattle in a pasture system. Temperatures in shade and direct sunlight were measured using black globe temperature (BGT) data loggers. Time-lapse images from game cameras were used to obtain counts of shade usage, coloration, orientation, and behavior of cattle throughout the daytime hours. In general, we found that shade utilization and most of the predominating orientations and behaviors differed significantly ( P < 0.05) by both time of day (Hour) and BGT in direct sunlight (BGTsun), while interactions between these two effects (Hour × BGTsun) were often nonsignificant. The mean percentage of the herd using shade was highest in mid-morning (87-96%) and early afternoon (97%), but also increased with BGTsun regardless of the time of day; these trends were similar for both dark- and light-colored cattle. Lying down was the dominant behavior exhibited in the shade, while foraging was the most prevalent behavior in the sun. When herd shade usage was lowest in mid- to late-afternoon (<1%) we also observed an increase in the use of heat-mitigating orientations in the sun (37-47%). We discuss some practical implications of these results, including the potential use of temperature thresholds to interpret cattle behaviors and shade usage.

Modeling shade tree use by beef cattle as a function of black globe temperature and time of day.

PubMed

Foust, Amanda M; Headlee, William L

2017-12-01

Increasing temperatures associated with global climate change threaten to disrupt agricultural systems such as beef production, yet relatively little is known about the use of natural tree shade to mitigate the negative effects of heat stress on beef cattle. In this study, we evaluated how temperature and time of day influenced the utilization of tree shade in relation to coloration, orientation, and behavior of beef cattle in a pasture system. Temperatures in shade and direct sunlight were measured using black globe temperature (BGT) data loggers. Time-lapse images from game cameras were used to obtain counts of shade usage, coloration, orientation, and behavior of cattle throughout the daytime hours. In general, we found that shade utilization and most of the predominating orientations and behaviors differed significantly (P < 0.05) by both time of day (Hour) and BGT in direct sunlight (BGT sun ), while interactions between these two effects (Hour × BGT sun ) were often nonsignificant. The mean percentage of the herd using shade was highest in mid-morning (87-96%) and early afternoon (97%), but also increased with BGT sun regardless of the time of day; these trends were similar for both dark- and light-colored cattle. Lying down was the dominant behavior exhibited in the shade, while foraging was the most prevalent behavior in the sun. When herd shade usage was lowest in mid- to late-afternoon (<1%) we also observed an increase in the use of heat-mitigating orientations in the sun (37-47%). We discuss some practical implications of these results, including the potential use of temperature thresholds to interpret cattle behaviors and shade usage.

Real-time Supervised Detection of Pink Areas in Dermoscopic Images of Melanoma: Importance of Color Shades, Texture and Location

PubMed Central

Kaur, Ravneet; Albano, Peter P.; Cole, Justin G.; Hagerty, Jason; LeAnder, Robert W.; Moss, Randy H.; Stoecker, William V.

2015-01-01

Background/Purpose Early detection of malignant melanoma is an important public health challenge. In the USA, dermatologists are seeing more melanomas at an early stage, before classic melanoma features have become apparent. Pink color is a feature of these early melanomas. If rapid and accurate automatic detection of pink color in these melanomas could be accomplished, there could be significant public health benefits. Methods Detection of three shades of pink (light pink, dark pink, and orange pink) was accomplished using color analysis techniques in five color planes (red, green, blue, hue and saturation). Color shade analysis was performed using a logistic regression model trained with an image set of 60 dermoscopic images of melanoma that contained pink areas. Detected pink shade areas were further analyzed with regard to the location within the lesion, average color parameters over the detected areas, and histogram texture features. Results Logistic regression analysis of a separate set of 128 melanomas and 128 benign images resulted in up to 87.9% accuracy in discriminating melanoma from benign lesions measured using area under the receiver operating characteristic curve. The accuracy in this model decreased when parameters for individual shades, texture, or shade location within the lesion were omitted. Conclusion Texture, color, and lesion location analysis applied to multiple shades of pink can assist in melanoma detection. When any of these three details: color location, shade analysis, or texture analysis were omitted from the model, accuracy in separating melanoma from benign lesions was lowered. Separation of colors into shades and further details that enhance the characterization of these color shades are needed for optimal discrimination of melanoma from benign lesions. PMID:25809473

Real-time supervised detection of pink areas in dermoscopic images of melanoma: importance of color shades, texture and location.

PubMed

Kaur, R; Albano, P P; Cole, J G; Hagerty, J; LeAnder, R W; Moss, R H; Stoecker, W V

2015-11-01

Early detection of malignant melanoma is an important public health challenge. In the USA, dermatologists are seeing more melanomas at an early stage, before classic melanoma features have become apparent. Pink color is a feature of these early melanomas. If rapid and accurate automatic detection of pink color in these melanomas could be accomplished, there could be significant public health benefits. Detection of three shades of pink (light pink, dark pink, and orange pink) was accomplished using color analysis techniques in five color planes (red, green, blue, hue, and saturation). Color shade analysis was performed using a logistic regression model trained with an image set of 60 dermoscopic images of melanoma that contained pink areas. Detected pink shade areas were further analyzed with regard to the location within the lesion, average color parameters over the detected areas, and histogram texture features. Logistic regression analysis of a separate set of 128 melanomas and 128 benign images resulted in up to 87.9% accuracy in discriminating melanoma from benign lesions measured using area under the receiver operating characteristic curve. The accuracy in this model decreased when parameters for individual shades, texture, or shade location within the lesion were omitted. Texture, color, and lesion location analysis applied to multiple shades of pink can assist in melanoma detection. When any of these three details: color location, shade analysis, or texture analysis were omitted from the model, accuracy in separating melanoma from benign lesions was lowered. Separation of colors into shades and further details that enhance the characterization of these color shades are needed for optimal discrimination of melanoma from benign lesions. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Shaded Relief of Rio Sao Francisco, Brazil

NASA Image and Video Library

2000-02-14

This topographic image acquired by SRTM shows an area south of the Sao Francisco River in Brazil. The scrub forest terrain shows relief of about 400 meters (1300 feet). Areas such as these are difficult to map by traditional methods because of frequent cloud cover and local inaccessibility. This region has little topographic relief, but even subtle changes in topography have far-reaching effects on regional ecosystems. The image covers an area of 57 km x 79 km and represents one quarter of the 225 km SRTM swath. Colors range from dark blue at water level to white and brown at hill tops. The terrain features that are clearly visible in this image include tributaries of the Sao Francisco, the dark-blue branch-like features visible from top right to bottom left, and on the left edge of the image, and hills rising up from the valley floor. The San Francisco River is a major source of water for irrigation and hydroelectric power. Mapping such regions will allow scientists to better understand the relationships between flooding cycles, forestation and human influences on ecosystems. This shaded relief image was generated using topographic data from the Shuttle Radar Topography Mission. A computer-generated artificial light source illuminates the elevation data to produce a pattern of light and shadows. Slopes facing the light appear bright, while those facing away are shaded. On flatter surfaces, the pattern of light and shadows can reveal subtle features in the terrain. Shaded relief maps are commonly used in applications such as geologic mapping and land use planning. http://photojournal.jpl.nasa.gov/catalog/PIA02700

Growth, biomass allocation and photosynthesis of invasive and native Hawaiian rainforest species.

PubMed

Pattison, R R; Goldstein, G; Ares, A

1998-12-01

Growth, biomass allocation, and photosynthetic characteristics of seedlings of five invasive non-indigenous and four native species grown under different light regimes were studied to help explain the success of invasive species in Hawaiian rainforests. Plants were grown under three greenhouse light levels representative of those found in the center and edge of gaps and in the understory of Hawaiian rainforests, and under an additional treatment with unaltered shade. Relative growth rates (RGRs) of invasive species grown in sun and partial shade were significantly higher than those for native species, averaging 0.25 and 0.17 g g -1 week -1 , respectively, while native species averaged only 0.09 and 0.06 g g -1 week -1 , respectively. The RGR of invasive species under the shade treatment was 40% higher than that of native species. Leaf area ratios (LARs) of sun and partial-shade-grown invasive and native species were similar but the LAR of invasive species in the shade was, on average, 20% higher than that of native species. There were no differences between invasive and native species in biomass allocation to shoots and roots, or in leaf mass per area across light environments. Light-saturated photosynthetic rates (Pmax) were higher for invasive species than for native species in all light treatments. Pmax of invasive species grown in the sun treatment, for example, ranged from 5.5 to 11.9 μmol m -2 s -1 as compared with 3.0-4.5 μmol m -2 s -1 for native species grown under similar light conditions. The slope of the linear relationship between Pmax and dark respiration was steeper for invasive than for native species, indicating that invasive species assimilate more CO 2 at a lower respiratory cost than native species. These results suggest that the invasive species may have higher growth rates than the native species as a consequence of higher photosynthetic capacities under sun and partial shade, lower dark respiration under all light treatments, and higher LARs when growing under shade conditions. Overall, invasive species appear to be better suited than native species to capturing and utilizing light resources, particularly in high-light environments such as those characterized by relatively high levels of disturbance.

Light compensation points in shade-grown seedlings of deciduous broadleaf tree species with different successional traits raised under elevated CO2.

PubMed

Kitao, M; Hida, T; Eguchi, N; Tobita, H; Utsugi, H; Uemura, A; Kitaoka, S; Koike, T

2016-01-01

We measured leaf photosynthetic traits in shade-grown seedlings of four tree species native to northern Japan, raised under an elevated CO2 condition, to investigate the effects of elevated CO2 on shade tolerance of deciduous broadleaf tree species with different successional traits. We considered Betula platyphylla var. japonica and Betula maximowicziana as pioneer species, Quercus mongolica var. crispula as a mid-successional species, and Acer mono as a climax species. The plants were grown under shade conditions (10% of full sunlight) in a CO2 -regulated phytotron. Light compensation points (LCPs) decreased in all tree species when grown under elevated CO2 (720 μmol·mol(-1) ), which were accompanied by higher apparent quantum yields but no photosynthetic down-regulation. LCPs in Q. mongolica and A. mono grown under elevated CO2 were lower than those in the two pioneer birch species. The LCP in Q. mongolica seedlings was not different from that of A. mono in each CO2 treatment. However, lower dark respiration rates were observed in A. mono than in Q. mongolica, suggesting higher shade tolerance in A. mono as a climax species in relation to carbon loss at night. Thus, elevated CO2 may have enhanced shade tolerance by lowering LCPs in all species, but the ranking of shade tolerance related to successional traits did not change among species under elevated CO2 , i.e. the highest shade tolerance was observed in the climax species (A. mono), followed by a gap-dependent species (Q. mongolica), while lower shade tolerance was observed in the pioneer species (B. platyphylla and B. maximowicziana). © 2015 German Botanical Society and The Royal Botanical Society of the Netherlands.

North Dakota Floods

NASA Image and Video Library

2009-04-19

The Spring, 2009 floods along the Red River between North Dakota and Minnesota affected cities in the two states, especially Fargo and Whitehead. NASA Terra spacecraft acquired this image on April 9, 2009. This image shows the flood waters north of the towns spilling over into farmlands. Residents were on constant flood alert, filling sandbags, and hoping that the water level would finally recede. Standing water appears in shades of dark green and brown, wet ground is dark grey, and snow is white. http://photojournal.jpl.nasa.gov/catalog/PIA11989

NASA Spacecraft Monitors Continuing Burn of Arizona Largest-Ever Wildfire

NASA Image and Video Library

2011-06-22

NASA Terra spacecraft acquired this image of the Wallow fire in Arizona on June 21, 2011; vegetation appears in red, bare ground in shades of tan, burned areas in black and very-dark red; and smoke from the active fire front appears gray.

Effects of Solar Ultraviolet Radiation on the Potential Efficiency of Photosystem II in Leaves of Tropical Plants1

PubMed Central

Krause, G. Heinrich; Schmude, Claudia; Garden, Hermann; Koroleva, Olga Y.; Winter, Klaus

1999-01-01

The effects of solar ultraviolet (UV)-B and UV-A radiation on the potential efficiency of photosystem II (PSII) in leaves of tropical plants were investigated in Panama (9°N). Shade-grown tree seedlings or detached sun leaves from the outer crown of mature trees were exposed for short periods (up to 75 min) to direct sunlight filtered through plastic or glass filters that absorbed either UV-B or UV-A+B radiation, or transmitted the complete solar spectrum. Persistent changes in potential PSII efficiency were monitored by means of the dark-adapted ratio of variable to maximum chlorophyll a fluorescence. In leaves of shade-grown tree seedlings, exposure to the complete solar spectrum resulted in a strong decrease in potential PSII efficiency, probably involving protein damage. A substantially smaller decline in the dark-adapted ratio of variable to maximum chlorophyll a fluorescence was observed when UV-B irradiation was excluded. The loss in PSII efficiency was further reduced by excluding both UV-B and UV-A light. The photoinactivation of PSII was reversible under shade conditions, but restoration of nearly full activity required at least 10 d. Repeated exposure to direct sunlight induced an increase in the pool size of xanthophyll cycle pigments and in the content of UV-absorbing vacuolar compounds. In sun leaves of mature trees, which contained high levels of UV-absorbing compounds, effects of UV-B on PSII efficiency were observed in several cases and varied with developmental age and acclimation state of the leaves. The results show that natural UV-B and UV-A radiation in the tropics may significantly contribute to photoinhibition of PSII during sun exposure in situ, particularly in shade leaves exposed to full sunlight. PMID:10594122

Mobile Bay, Alabama area seen in Skylab 4 Earth Resources Experiment Package

NASA Image and Video Library

1974-02-01

SL4-92-300 (February 1974) --- A near vertical view of the Mobile Bay, Alabama area is seen in this Skylab 4 Earth Resources Experiments Package S190-B (five-inch earth terrain camera) photograph taken from the Skylab space station in Earth orbit. North of Mobile the Tombigbee and Alabama Rivers join to form the Mobile River. Detailed configuration of the individual stream channels and boundaries can be defined as the Mobile River flows into Mobile Bay, and thence into the Gulf of Mexico. The Mobile River Valley with its numerous stream channels is a distinct light shade in contrast to the dark green shade of the adjacent areas. The red coloration of Mobile Bay reflects the sediment load carried into the Bay by the rivers. Variations in red color indicate sediment load and the current paths within Mobile Bay. The waterly movement of the along shore currents at the mouth of Mobile Bay is shown by the contrasting light blue of the sediment-laden current and the blue of the Gulf predominately. Agricultural areas east and west of Mobile Bay are characterized by a rectangular pattern in green to white shades. Color variations may reflect the type and growth cycle of crops. Agricultural areas (light gray-greens) are also clearly visible in other parts of the photograph. Interstate 10 extends from near Pascagoula, Mississippi eastward through Mobile to the outskirts of Pensacola, Florida. Analysis of the EREP photographic data will be undertaken by the U.S. Corps of Engineers to determine bay dynamic processes. Federal agencies participating with NASA on the EREP project are the Departments of Agriculture, Commerce, Interior, the Environmental Protection Agency and the Corps of Engineers. All EREP photography is available to the public through the Department of Interior's Earth Resources Observations Systems Data Center, Sioux Falls, South Dakota. 57198 Photo credit: NASA

Visual performance with sport-tinted contact lenses in natural sunlight.

PubMed

Erickson, Graham B; Horn, Fraser C; Barney, Tyler; Pexton, Brett; Baird, Richard Y

2009-05-01

The use of tinted and clear contact lenses (CLs) in all aspects of life is becoming a more popular occurrence, particularly in athletic activities. This study broadens previous research regarding performance-tinted CLs and their effects on measures of visual performance. Thirty-three subjects (14 male, 19 female) were fitted with clear B&L Optima 38, 50% visible light transmission Amber and 36% visible light transmission Gray-Green Nike Maxsight CLs in an individualized randomized sequence. Subjects were dark-adapted with welding goggles before testing and in between subtests involving a Bailey-Lovie chart and the Haynes Distance Rock test. The sequence of testing was repeated for each lens modality. The Amber and Gray-Green lenses enabled subjects to recover vision faster in bright sunlight compared with clear lenses. Also, subjects were able to achieve better visual recognition in bright sunlight when compared with clear lenses. Additionally, the lenses allowed the subjects to alternate fixation between a bright and shaded target at a more rapid rate in bright sunlight as compared with clear lenses. Subjects preferred both the Amber and Gray-Green lenses over clear lenses in the bright and shadowed target conditions. The results of the current study show that Maxsight Amber and Gray-Green lenses provide better contrast discrimination in bright sunlight, better contrast discrimination when alternating between bright and shaded target conditions, better speed of visual recovery in bright sunlight, and better overall visual performance in bright and shaded target conditions compared with clear lenses.

4. View of Clovelley Farm tenant house, back side (east) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. View of Clovelley Farm tenant house, back side (east) area of two room addition. Note dark metal heating oil tank against rear wall and silver maple trees to shade house from south and east. - Clovelley Farm Tenant House, 4958 Paris Road (east side), Paris, Bourbon County, KY

Functional traits and plasticity in response to light in seedlings of four Iberian forest tree species.

PubMed

Sánchez-Gómez, David; Valladares, Fernando; Zavala, Miguel A

2006-11-01

We investigated the differential roles of physiological and morphological features on seedling survivorship along an experimental irradiance gradient in four dominant species of cool temperate-Mediterranean forests (Quercus robur L., Quercus pyrenaica Willd., Pinus sylvestris L. and Pinus pinaster Ait.). The lowest photochemical efficiency (F(v)/F(m) in dark-adapted leaves) was reached in deep shade (1% of full sunlight) in all species except Q. robur, which had the lowest photochemical efficiency in both deep shade and 100% of full sunlight. Species differed significantly in their survival in 1% of full sunlight but exhibited similar survivorship in 6, 20 and 100% of full sunlight. Shade-tolerant oaks had lower leaf area ratios, shoot to root ratios, foliage allocation ratios and higher rates of allocation to structural biomass (stem plus thick roots) than shade-intolerant pines. Overall phenotypic plasticity for each species, estimated as the difference between the minimum and the maximum mean values of the ecophysiological variables studied at the various irradiances divided by the maximum mean value of those variables, was inversely correlated with shade tolerance. Observed morphology, allocation and plasticity conformed to a conservative resource-use strategy, although observed differences in specific leaf area, which was higher in shade-tolerant species, supported a carbon gain maximization strategy. Lack of a congruent suite of traits underlying shade tolerance in the studied species provides evidence of adaptation to multiple selective forces. Although the study was based on only four species, the importance of ecophysiological variables as determinants of interspecific differences in survival in limiting light was demonstrated.

Ecological filtering by a dominant herb selects for shade tolerance in the tree seedling community of coastal dune forest.

PubMed

Tsvuura, Zivanai; Griffiths, Megan E; Gunton, Richard M; Franks, Peter J; Lawes, Michael J

2010-12-01

The regeneration niche is commonly partitioned along a gradient from shade-tolerant to shade-intolerant species to explain plant community assembly in forests. We examined the shade tolerance of tree seedlings in a subtropical coastal forest to determine whether the ecological filtering effect of a dominant, synchronously monocarpic herb (Isoglossa woodii) selects for species at either end of the light response continuum during the herb's vegetative and reproductive phases. Photosynthetic characteristics of seedlings of 20 common tree species and the herb were measured. Seedlings were grown in the greenhouse at 12-14% irradiance, and their light compensation points measured using an open-flow gas exchange system. The light compensation points for the tree species were low, falling within a narrow range from 2.1 ± 0.8 μmol m(-2) s(-1) in Celtis africana to 6.4 ± 0.7 μmol m(-2) s(-1) in Allophylus natalensis, indicating general shade tolerance, consistent with a high and narrow range of apparent quantum yield among species (0.078 ± 0.002 mol CO(2) mol(-1) photon). Rates of dark respiration were significantly lower in a generalist pioneer species (Acacia karroo) than in a forest pioneer (C. africana), or in late successional phase forest species. We argue that the general shade tolerance, and phenotypic clustering of shade tolerance, in many tree species from several families in this system, is a result of ecological filtering by the prevailing low light levels beneath the I. woodii understorey, which excludes most light-demanding species from the seedling community.

Karrikins delay soybean seed germination by mediating abscisic acid and gibberellin biogenesis under shaded conditions

PubMed Central

Meng, Yongjie; Chen, Feng; Shuai, Haiwei; Luo, Xiaofeng; Ding, Jun; Tang, Shengwen; Xu, Shuanshuan; Liu, Jianwei; Liu, Weiguo; Du, Junbo; Liu, Jiang; Yang, Feng; Sun, Xin; Yong, Taiwen; Wang, Xiaochun; Feng, Yuqi; Shu, Kai; Yang, Wenyu

2016-01-01

Karrikins (KAR) are a class of signal compounds, discovered in wildfire smoke, which affect seed germination. Currently, numerous studies have focused on the model plant Arabidopsis in the KAR research field, rather than on crops. Thus the regulatory mechanisms underlying KAR regulation of crop seed germination are largely unknown. Here, we report that KAR delayed soybean seed germination through enhancing abscisic acid (ABA) biosynthesis, while impairing gibberellin (GA) biogenesis. Interestingly, KAR only retarded soybean seed germination under shaded conditions, rather than under dark and white light conditions, which differs from in Arabidopsis. Phytohormone quantification showed that KAR enhanced ABA biogenesis while impairing GA biosynthesis during the seed imbibition process, and subsequently, the ratio of active GA4 to ABA was significantly reduced. Further qRT-PCR analysis showed that the transcription pattern of genes involved in ABA and GA metabolic pathways are consistent with the hormonal measurements. Finally, fluridone, an ABA biogenesis inhibitor, remarkably rescued the delayed-germination phenotype of KAR-treatment; and paclobutrazol, a GA biosynthesis inhibitor, inhibited soybean seed germination. Taken together, these evidences suggest that KAR inhibit soybean seed germination by mediating the ratio between GA and ABA biogenesis. PMID:26902640

Karrikins delay soybean seed germination by mediating abscisic acid and gibberellin biogenesis under shaded conditions.

PubMed

Meng, Yongjie; Chen, Feng; Shuai, Haiwei; Luo, Xiaofeng; Ding, Jun; Tang, Shengwen; Xu, Shuanshuan; Liu, Jianwei; Liu, Weiguo; Du, Junbo; Liu, Jiang; Yang, Feng; Sun, Xin; Yong, Taiwen; Wang, Xiaochun; Feng, Yuqi; Shu, Kai; Yang, Wenyu

2016-02-23

Karrikins (KAR) are a class of signal compounds, discovered in wildfire smoke, which affect seed germination. Currently, numerous studies have focused on the model plant Arabidopsis in the KAR research field, rather than on crops. Thus the regulatory mechanisms underlying KAR regulation of crop seed germination are largely unknown. Here, we report that KAR delayed soybean seed germination through enhancing abscisic acid (ABA) biosynthesis, while impairing gibberellin (GA) biogenesis. Interestingly, KAR only retarded soybean seed germination under shaded conditions, rather than under dark and white light conditions, which differs from in Arabidopsis. Phytohormone quantification showed that KAR enhanced ABA biogenesis while impairing GA biosynthesis during the seed imbibition process, and subsequently, the ratio of active GA4 to ABA was significantly reduced. Further qRT-PCR analysis showed that the transcription pattern of genes involved in ABA and GA metabolic pathways are consistent with the hormonal measurements. Finally, fluridone, an ABA biogenesis inhibitor, remarkably rescued the delayed-germination phenotype of KAR-treatment; and paclobutrazol, a GA biosynthesis inhibitor, inhibited soybean seed germination. Taken together, these evidences suggest that KAR inhibit soybean seed germination by mediating the ratio between GA and ABA biogenesis.

Initial characterization of shade avoidance response suggests functional diversity between Populus phytochrome B genes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karve, Abhijit A; Weston, David; Jawdy, Sara

2012-01-01

Shade avoidance signaling in higher plants involves perception of the incident red/far-red (R/FR) light by phytochromes and the modulation of downstream transcriptional networks to regulate developmental plasticity in relation to heterogeneous light environments. In this study, we characterized the expression and functional features of Populus phytochrome (PHY) gene family as well as the transcriptional responses of Populus to the changes in R/FR light. Expression data indicated that PHYA is the predominant PHY in the dark grown Populus seedling whereas PHYBs are most abundant in mature tissue types. Out of three Populus PHYs, PHYA is light labile and localized to cytosolmore » in dark whereas both PHYB1 and PHYB2 are light stable and are localized to nucleus in mesophyll protoplasts. When expressed in Arabidopsis, PHYB1 rescued Arabidopsis phyB mutant phenotype whereas PHYB2 did not, suggesting functional diversification between these two gene family members. However, phenotypes of transgenic Populus lines with altered expression of PHYB1, PHYB2 or both and the expression of candidate shade response genes in these transgenic lines suggest that PHYB1 and PHYB2 may have distinct yet overlapping functions. The RNAseq results and analysis of Populus exposed to enriched-FR light indicate that genes associated in cell wall modification and brassinosteroid signaling were induced under far red light. Overall our data indicate that Populus transcriptional responses are at least partially conserved with Arabidopsis.« less

Kubelka-Munk reflectance theory applied to porcelain veneer systems using a colorimeter.

PubMed

Davis, B K; Johnston, W M; Saba, R F

1994-01-01

The purpose of this study was to demonstrate the ability of Kubelka-Munk reflectance theory to predict color parameters of veneer porcelain on various backings using colorimetric measurements. Tristimulus absorption and scattering coefficients were used to predict the respective tristimulus reflectance values of A1, D3, and translucent porcelain samples after they had been bonded to light and dark substrates using universal, opaque, and untinted shades of bonding resin. Observed and predicted reflectance values exhibited high correlation (r2 > or = 0.93 for each porcelain shade). Kubelka-Munk theory offers an accurate prediction for the resultant colorimetric reflectance parameters of veneer porcelain bonded to variously colored backings.

The genetics of colour in fat-tailed sheep: a review.

PubMed

Lundie, Roger S

2011-10-01

Fat-tailed sheep come in various colours-most are either brown (tan) or black. In some, most of the body is white with the tan or black colour restricted to the front portion of the body or to just around the eyes, muzzle and parts of the legs. The Karakul breed is important for the production of lamb skins of various colours for the fashion industry. As well as the black and tan colours there are Karakuls bred for grey or roan shades, a white colour or one of the numerous Sur shades. In the Sur shades, the base of the birthcoat fibre is one of a number of dark shades and the tip a lighter or white shade. All these colours and many others are the result of the interaction of various genes that determine the specifics of the coat colour of the sheep. A number of sets of nomenclature and symbols have been used to represent the various loci and their alleles that are involved. In the 1980s and 1990s, a standardised set, based closely on those of the mouse and other species was developed. Using this as the framework, the alleles of the Extension, Agouti, Brown, Spotting, Pigmented Head and Roan loci are described using fat-tailed sheep (mainly Damara, Karakul and Persian) as examples. Further discussion includes other types of "white markings," the Ticking locus and the Sur loci.

From Dark to Light: Skin Color and Wages among African-Americans

ERIC Educational Resources Information Center

Goldsmith, Arthur H.; Hamilton, Darrick; Darity, William, Jr.

2007-01-01

This paper develops and tests a theory, referred to as "preference for whiteness," which predicts that the interracial (white-black) and intraracial wage gap widens as the skin shade of the black worker darkens. Using data drawn from the Multi City Study of Urban Inequality and the National Survey of Black Americans, we report evidence…

7 CFR 51.1860 - Color classification.

Code of Federal Regulations, 2010 CFR

2010-01-01

... variety: (1) Green. “Green” means that the surface of the tomato is completely green in color. The shade of green color may vary from light to dark; (2) Breakers. “Breakers” means that there is a definite break in color from green to tannish-yellow, pink or red on not more than 10 percent of the surface; (3...

Spectral determination of concentrations of functionally diverse pigments in increasingly complex arctic tundra canopies.

PubMed

Boelman, Natalie T; Magney, Troy S; Logan, Barry A; Griffin, Kevin L; Eitel, Jan U H; Greaves, Heather; Prager, Case M; Vierling, Lee A

2016-09-01

As the Arctic warms, tundra vegetation is becoming taller and more structurally complex, as tall deciduous shrubs become increasingly dominant. Emerging studies reveal that shrubs exhibit photosynthetic resource partitioning, akin to forests, that may need accounting for in the "big leaf" net ecosystem exchange models. We conducted a lab experiment on sun and shade leaves from S. pulchra shrubs to determine the influence of both constitutive (slowly changing bulk carotenoid and chlorophyll pools) and facultative (rapidly changing xanthophyll cycle) pigment pools on a suite of spectral vegetation indices, to devise a rapid means of estimating within canopy resource partitioning. We found that: (1) the PRI of dark-adapted shade leaves (PRIo) was double that of sun leaves, and that PRIo was sensitive to variation among sun and shade leaves in both xanthophyll cycle pool size (V + A + Z) (r (2) = 0.59) and Chla/b (r (2) = 0.64); (2) A corrected PRI (difference between dark and illuminated leaves, ΔPRI) was more sensitive to variation among sun and shade leaves in changes to the epoxidation state of their xanthophyll cycle pigments (dEPS) (r (2) = 0.78, RMSE = 0.007) compared to the uncorrected PRI of illuminated leaves (PRI) (r (2) = 0.34, RMSE = 0.02); and (3) the SR680 index was correlated with each of (V + A + Z), lutein, bulk carotenoids, (V + A + Z)/(Chla + b), and Chla/b (r (2) range = 0.52-0.69). We suggest that ΔPRI be employed as a proxy for facultative pigment dynamics, and the SR680 for the estimation of constitutive pigment pools. We contribute the first Arctic-specific information on disentangling PRI-pigment relationships, and offer insight into how spectral indices can assess resource partitioning within shrub tundra canopies.

Solid perception mechanism by a shading pattern: spatial frequency components in a corrugated wave pattern.

PubMed

Nameda, N

1988-01-01

Illumination allows solid object perception to be obtained and depicted by a shading pattern produced by lighting. The shading cue, as one of solid perception cues (Gibson 1979), was investigated in regard to a white corrugated wave shape, using computer graphic device: Tospix-2. The reason the corrugated wave was chosen, is that an alternately bright and dark pattern, produced by shading, can be conveniently analyzed into contained spatial frequencies. This paper reports spatial frequency properties contained in the shading pattern. The shading patterns, input into the computer graphic device, are analyzed by Fourier Transformation by the same device. After the filtration by various spatial frequency low and high pass filters, Inverse Fourier Transformation is carried out for the residual components. The result of the analysis indicates that the third through higher harmonics components are important in regard to presenting a solid reality feeling in solid perception. Sakata (1983) also reported that an edged pattern, superimposed onto a lower sinusoidal pattern, was important in solid perception. The third through higher harmonics components express the changing position of luminance on the pattern, and a slanted plane relating to the light direction. Detection of a solid shape, constructed with flat planes, is assumed to be on the bottom of the perfect curved solid perception mechanism. Apparent evidence for this assumption, in difficult visual conditions, is that a flat paneled solid is seen before the curved solid. This mechanism is explained by two spatial frequency neural network systems, assumed as having correspondence with higher spatial frequency detection and lower spatial frequency detection.

Species-Independent Down-Regulation of Leaf Photosynthesis and Respiration in Response to Shading: Evidence from Six Temperate Tree Species

PubMed Central

Chen, Anping; Lichstein, Jeremy W.; Osnas, Jeanne L. D.; Pacala, Stephen W.

2014-01-01

The ability to down-regulate leaf maximum net photosynthetic capacity (Amax) and dark respiration rate (Rdark) in response to shading is thought to be an important adaptation of trees to the wide range of light environments that they are exposed to across space and time. A simple, general rule that accurately described this down-regulation would improve carbon cycle models and enhance our understanding of how forest successional diversity is maintained. In this paper, we investigated the light response of Amax and Rdark for saplings of six temperate forest tree species in New Jersey, USA, and formulated a simple model of down-regulation that could be incorporated into carbon cycle models. We found that full-sun values of Amax and Rdark differed significantly among species, but the rate of down-regulation (proportional decrease in Amax or Rdark relative to the full-sun value) in response to shade was not significantly species- or taxon-specific. Shade leaves of sun-grown plants appear to follow the same pattern of down-regulation in response to shade as leaves of shade-grown plants. Given the light level above a leaf and one species-specific number (either the full-sun Amax or full-sun Rdark), we provide a formula that can accurately predict the leaf's Amax and Rdark. We further show that most of the down regulation of per unit area Rdark and Amax is caused by reductions in leaf mass per unit area (LMA): as light decreases, leaves get thinner, while per unit mass Amax and Rdark remain approximately constant. PMID:24727745

78 FR 24701 - Endangered and Threatened Wildlife; 90-Day Finding on Petitions To List the Great Hammerhead...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

... ``may be'' warranted. As a general matter, these decisions hold that a petition need not establish a... dorsal side colored dark brown to light grey or olive that shades to white on the ventral side (Compagno... this region lack the resources to provide effective or, for that matter, any enforcement, with some...

[Preparation and chromaticity properties of colored dental 3Y-TZP ceramics].

PubMed

Yi, Yuan-fu; Wang, Chen; Tian, Jie-mo; Liu, Hong-chen; Wen, Ning

2008-10-01

To obtain and investigate the chromaticity properties of colored dental 3Y-TZP ceramics with different colorant combinations. Colorant combinations were mixed with TZ-3Y-S powder, then the mixtures were compacted at 200 MPa using cold isostatic pressure, densely sintered at 1500 degrees C for 2 h forming 5 graded colored dental zirconia ceramics. Specimen were sectioned into 10 mm x 10 mm x 0.5 mm and 10 mm x l0 mmx 1 mm slices from the sintered blocks. Color measurement was performed under black background using spectrophotometer. The chromaticity properties were compared with that of the VITA In-Ceram YZ shade guide. Five colored dental zirconia ceramics were obtained. The lightness decreased gradually, and the chroma value increased gradually. The color differences of the two thickness specimens were little. The parameters of the color space were L*: 67.76-77.78; a*: -2.19-3.80; b*: 12.13-25.01, which was similar with that of the VITA In-Ceram YZ shade guide, while the lowest value of lightness was relatively higher than that of the VITA In-Ceram YZ shade guide. Colored 3Y-TZP dental ceramics are suitable for clinical use. There is a need to develop more darkness shaded zirconia dental ceramics.

Colour stability of denture teeth submitted to different cleaning protocols and accelerated artificial aging.

PubMed

Freire, T S; Aguilar, F G; Garcia, L da Fonseca Roberti; Pires-de-Souza, F de Carvalho Panzeri

2014-03-01

Acrylic resin is widely used for artificial teeth manufacturing due to several important characteristics; however, this material do not present acceptable colour stability over the course of time. This study evaluated the effect of different cleaning protocols and accelerated artificial aging on colour stability of denture teeth made of acrylic resin. Sixty denture teeth in dark and light shades were used, and separated according to the treatment to which they were submitted. Results demonstrated that colour stability of artificial teeth is influenced by the cleaning solution and artificial aging, being dark teeth more susceptible to colour alteration than lighter ones.

Shade effects on growth, flowering, and fruit of apple

USDA-ARS?s Scientific Manuscript database

Light is a critical resource needed by plants for growth and reproduction. A major portion of the apple (Malus xdomestica Borkh.) tree’s canopy is subjected to shade during most daylight hours each day and such shade may affect productivity. The current research determined effects of morning, afte...

SU-E-J-17: Evaluation of Metal Artifact Reduction in MVCTs Using a Model Based Image Reconstruction Method.

PubMed

Paudel, M; MacKenzie, M; Fallone, B; Rathee, S

2012-06-01

To evaluate the performance of a model based image reconstruction in reducing metal artifacts in MVCT systems, and to compare with filtered-back projection (FBP) technique. Iterative maximum likelihood polychromatic algorithm for CT (IMPACT) is used with pair/triplet production process and the energy dependent response of detectors. The beam spectra for in-house bench-top and TomotherapyTM MVCT are modelled for use in IMPACT. The energy dependent gain of detectors is calculated using a constrained optimization technique and measured attenuation produced by 0 - 24 cm thick solid water slabs. A cylindrical (19 cm diameter) plexiglass phantom containing various central cylindrical inserts (relative electron density of 0.28-1.69) between two steel rods (2 cm diameter) is scanned in the bench-top [the bremsstrahlung radiation from 6 MeV electron beam passed through 4 cm solid water on the Varian Clinac 2300C] and TomotherapyTM MVCTs. The FBP reconstructs images from raw signal normalised to air scan and corrected for beam hardening using a uniform plexi-glass cylinder (20 cm diameter). IMPACT starts with FBP reconstructed seed image and reconstructs final image at 1.25 MeV in 150 iterations. FBP produces a visible dark shading in the image between two steel rods that becomes darker with higher density central insert causing 5-8 % underestimation of electron density compared to the case without the steel rods. In the IMPACT image the dark shading connecting the steel rods is nearly removed and the uniform background restored. The average attenuation coefficients of the inserts and the background are very close to the corresponding theoretical values at 1.25 MeV. The dark shading metal artifact due to beam hardening can be removed in MVCT using the iterative reconstruction algorithm such as IMPACT. However, the accurate modelling of detectors' energy dependent response and physical processes are crucial for successful implementation. Funding support for the research is obtained from "Vanier Canada Graduate Scholarship" and "Canadian Institute of Health Research". © 2012 American Association of Physicists in Medicine.

World Globes, Shaded Relief and Colored Height

NASA Image and Video Library

2003-08-21

These images of the world were generated with data from the Shuttle Radar Topography Mission (SRTM). The SRTM Project has recently released a new global data set called SRTM30, where the original one arcsecond of latitude and longitude resolution (about 30 meters, or 98 feet, at the equator) was reduced to 30 arcseconds (about 928 meters, or 1496 feet.) These images were created from that data set and show the Earth as it would be viewed from a point in space centered over the Americas, Africa and the western Pacific. Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. http://photojournal.jpl.nasa.gov/catalog/PIA03394

Crassulacean acid metabolism (CAM) in an epiphytic ant-plant, Myrmecodia beccarii Hook.f. (Rubiaceae).

PubMed

Tsen, Edward W J; Holtum, Joseph A M

2012-09-01

This study demonstrates unequivocally the presence of crassulacean acid metabolism (CAM) in a species of the Rubiaceae, the fourth largest angiosperm plant family. The tropical Australian endemic epiphytic ant-plant, Myrmecodia beccarii Hook.f., exhibits net CO(2) uptake in the dark and a concomitant accumulation of titratable acidity in plants in the field and in cultivation. Plants growing near Cardwell, in a north Queensland coastal seasonally dry forest of Melaleuca viridiflora Sol. ex Gaertn., accumulated ~50 % of their 24 h carbon gain in the dark during the warm wet season. During the transition from the wet season to the dry season, 24 h carbon gain was reduced whilst the proportion of carbon accumulated during the dark increased. By mid dry season many plants exhibited zero net carbon uptake over 24 h, but CO(2) uptake in the dark was observed in some plants following localised rainfall. In a shade-house experiment, droughted plants in which CO(2) uptake in the light was absent and dark CO(2) uptake was reduced, were able to return to relatively high rates of CO(2) uptake in the light and dark within 12 h of rewatering.

Quantifying Discretization Effects on Brain Trauma Simulations

DTIC Science & Technology

2016-01-01

arbitrarily formed meshes can propagate error when resolving interactions among the skull , cerebrospinal fluid, and brain. We compared Lagrangian, pure...embedded methods from top to bottom. ......3 Fig. 2 Loading node-set for Eulerian rotational problem. The dark shaded area around the skull is the area to...and top inner edges of the skull . The example shown is a Lagrangian rotational model. The red and green materials represent the brain and skull

Evaluation of an optimized shade guide made from porcelain powder mixtures.

PubMed

Wang, Peng; Wei, Jiaqiang; Li, Qing; Wang, Yining

2014-12-01

Color errors associated with current shade guides and problems with color selection and duplication are still challenging for restorative dentists. The purpose of this study was to evaluate an optimized shade guide for visual shade duplication. Color distributions (L*, a*, and b*) of the maxillary left central incisors of 236 participants, whose ages ranged from 20 to 60, were measured with a spectrophotometer. Based on this color map, an optimized shade guide was designed with 14 shade tabs evenly distributed within the given color range of the natural incisors. The shade tabs were fabricated with porcelain powder mixtures and conventional laboratory procedures. A comparison of shade duplication by using the optimized and Vitapan Classical shade guides was conducted. Thirty Chinese participants were involved, and the colors of the left maxillary incisors were selected by using 2 shade guides. Metal ceramic crowns were fabricated according to the results of the shade selection. The colors of the shade tabs, natural teeth, and the ceramic crowns were measured with a spectrophotometer. The color differences among the natural teeth, the shade tabs, and the corresponding metal ceramic crowns were calculated and analyzed (α=.017). Significant differences were found in both phases of shade determination and shade duplication (P<.017). The total number of color errors with the optimized shade guide was 3.5, which was significantly less than that of Vitapan, 5.1 (P<.001). The optimized shade guide system improved performance not only in the color selection phase but also in the color of the fabricated crowns. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Shade avoidance components and pathways in adult plants revealed by phenotypic profiling.

PubMed

Nozue, Kazunari; Tat, An V; Kumar Devisetty, Upendra; Robinson, Matthew; Mumbach, Maxwell R; Ichihashi, Yasunori; Lekkala, Saradadevi; Maloof, Julin N

2015-04-01

Shade from neighboring plants limits light for photosynthesis; as a consequence, plants have a variety of strategies to avoid canopy shade and compete with their neighbors for light. Collectively the response to foliar shade is called the shade avoidance syndrome (SAS). The SAS includes elongation of a variety of organs, acceleration of flowering time, and additional physiological responses, which are seen throughout the plant life cycle. However, current mechanistic knowledge is mainly limited to shade-induced elongation of seedlings. Here we use phenotypic profiling of seedling, leaf, and flowering time traits to untangle complex SAS networks. We used over-representation analysis (ORA) of shade-responsive genes, combined with previous annotation, to logically select 59 known and candidate novel mutants for phenotyping. Our analysis reveals shared and separate pathways for each shade avoidance response. In particular, auxin pathway components were required for shade avoidance responses in hypocotyl, petiole, and flowering time, whereas jasmonic acid pathway components were only required for petiole and flowering time responses. Our phenotypic profiling allowed discovery of seventeen novel shade avoidance mutants. Our results demonstrate that logical selection of mutants increased success of phenotypic profiling to dissect complex traits and discover novel components.

Gravity-dependent regulation of red light induced moss protonemata branching and gametophore bud formation

NASA Astrophysics Data System (ADS)

Ripetskyj, R. T.; Kit, N. A.

Isolated leafy shoots of the moss Pottia intermedia positioned horizontally on the agar surface in vertically oriented petri dishes regenerate unbranching negatively gravitropic protonemata on upper side of the regenerant. Gravity determines the site of regeneration not the process itself. White light of low intensity unsufficient to induce positive phototropism of dark-grown protonemata can, however, provoke their branching and gametophore bud formation (Ripetskyj et al., 1998; 1999). The presented experiments have been carried out with red light in Biological Research in Canisters/Light Emitting Diode (BRIC/LED) hardware developed at Kennedy Space Center, USA. Seven-day-old dark-grown negatively gravitropic secondary P. intermedia protonemata were positioned differently with respect to gravity vector and to the source of red light of low, 1 or 2 μ mol\\cdot m-2\\cdot s-1, intensities. The light induced intensive branching of the protonemata and gametophore bud formation initiation site of both processes as well as the direction of growth of branches and buds being depent on the position of protonemata with respect to gravity and light vectors. Vertically positioned, i.e. ungravistimulated, dark grown protonemata illuminated from one side with red light of 2 μ mol\\cdot m-2\\cdot s-1 intensity produced 96,9 ± 2,2% of side branches and buds growing directly towards the light source from the lit protonema side. Horizontally disposed protonemata irradiated from below with red light of the same intensity regenerate 31,7 ± 3,9% of branches and buds on the upper, i.e. shaded protonemata side, the upward growth of which should undoubtedly be determined by gravity. In vertically disposed protonemata illuminated with red light of 1 μ mol\\cdot m-2\\cdot s-1 intensity from aside 31,9 ± 5,5% of side branches and buds arised on shaded protonema side and grew away from the light. Illumination of the protonemata in horizontal position from below increased the number of upgrowing branches and buds on upper shaded protonemata side to 76,9 ± 2,4%. The results convincingly speak for stimulating effect of the interaction of gravity and red light of low intensity. Characteristically, the number of side branches and buds on upper side of horizontally disposed protonemata illuminated from below (76,9 ± 2,4%) or parallely to protonemata length from their tips (86,0 ± 5,3%) were slightly, however, statistically significantly, greater than in the case of illumination from above (62,9 ± 3,1%). The effect may be probably be explained by some intensification of gravity action with red light of low intensity from shading of upper cell side or from lighting parallelly with respect to the cell surface. This research was supported by NASA grant NN-09(R).

Advanced MCT technologies at LETI for space applications

NASA Astrophysics Data System (ADS)

Durand, A.; Destefanis, G.; Gravrand, O.; Rothmann, J.

This document is a recap of an oral presentation made at Nice during the INSU Astrophysics Detector Workshop 2008. It aims at giving an overview of the achievements and ongoing developments presently carried out at CEA-LETI in the field of Infrared focal plane array. Although most of the research actually performed at LETI is not driven by space oriented application, the excellence and the cutting edge of the outcome is or can be applied to space-dedicated components. This paper focus on features and developments from which astrophysics observation would benefit in the near future on the European market. This encompassed “traditionnal” developments such as format enlargement, low dark current technology such as p/n structure but it also shade light on promising and thrilling development such as avalanche photodiode array. It eventually gives some hints of none MCT technologies processed at LETI.

Technical Progress of the New Worlds Observer Mission

NASA Astrophysics Data System (ADS)

Lo, Amy; Noecker, C.; Cash, W.; NWO Study Team

2009-01-01

We report on the technical progress of the New Worlds Observer (NWO) mission concept. NWO is a two spacecraft mission that is capable of detecting and characterizing extra-solar, terrestrial planets and planetary systems. NWO consists of an external starshade and an UV-optical space telescope, flying in tandem. The starshade is a petal-shaped, opaque screen that creates an extremely dark shadow large enough to shade the telescope aperture from the target star. The NWO team has been addressing the top technology challenges of the concept, and report here our progress. We will present the current mission configuration best suited to address Terrestrial Planet Finding requirements, and highlight the technological breakthroughs that we have achieved this year. In particular, we will report on progress made in precision deployables for the large starshade, and the trajectory & alignment control system for NWO. We will also briefly highlight advances in understanding the starshade optical performance.

Tracking the global maximum power point of PV arrays under partial shading conditions

NASA Astrophysics Data System (ADS)

Fennich, Meryem

This thesis presents the theoretical and simulation studies of the global maximum power point tracking (MPPT) for photovoltaic systems under partial shading. The main goal is to track the maximum power point of the photovoltaic module so that the maximum possible power can be extracted from the photovoltaic panels. When several panels are connected in series with some of them shaded partially either due to clouds or shadows from neighboring buildings, several local maxima appear in the power vs. voltage curve. A power increment based MPPT algorithm is effective in identifying the global maximum from the several local maxima. Several existing MPPT algorithms are explored and the state-of-the-art power increment method is simulated and tested for various partial shading conditions. The current-voltage and power-voltage characteristics of the PV model are studied under different partial shading conditions, along with five different cases demonstrating how the MPPT algorithm performs when shading switches from one state to another. Each case is supplemented with simulation results. The method of tracking the Global MPP is based on controlling the DC-DC converter connected to the output of the PV array. A complete system simulation including the PV array, the direct current to direct current (DC-DC) converter and the MPPT is presented and tested using MATLAB software. The simulation results show that the MPPT algorithm works very well with the buck converter, while the boost converter needs further changes and implementation.

High-Fidelity Geometric Modeling and Mesh Generation for Mechanics Characterization of Polycrystalline Materials

DTIC Science & Technology

2015-01-07

and anisotropic quadrilateral meshes, which can be used as the control mesh for high-order T- spline surface modeling. Archival publications (published...anisotropic T-meshes for the further T- spline surface construction. Finally, a gradient flow-based method is developed to improve the T-mesh quality...shade-off. Halos are bright or dark thin regions around the boundary of the sample. These false edges around the object make many segmentation

Decreased photochemical efficiency of photosystem II following sunlight exposure of shade-grown leaves of avocado: because of, or in spite of, two kinetically distinct xanthophyll cycles?

PubMed

Jia, Husen; Förster, Britta; Chow, Wah Soon; Pogson, Barry James; Osmond, C Barry

2013-02-01

This study resolved correlations between changes in xanthophyll pigments and photosynthetic properties in attached and detached shade-grown avocado (Persea americana) leaves upon sun exposure. Lutein epoxide (Lx) was deepoxidized to lutein (L), increasing the total pool by ΔL over 5 h, whereas violaxanthin (V) conversion to antheraxanthin (A) and zeaxanthin (Z) ceased after 1 h. During subsequent dark or shade recovery, de novo synthesis of L and Z continued, followed by epoxidation of A and Z but not of L. Light-saturated nonphotochemical quenching (NPQ) was strongly and linearly correlated with decreasing [Lx] and increasing [L] but showed a biphasic correlation with declining [V] and increasing [A+Z] separated when V deepoxidation ceased. When considering [ΔL+Z], the monophasic linear correlation was restored. Photochemical efficiency of photosystem II (PSII) and photosystem (PSI; deduced from the delivery of electrons to PSI in saturating single-turnover flashes) showed a strong correlation in their continuous decline in sunlight and an increase in NPQ capacity. This decrease was also reflected in the initial reduction of the slope of photosynthetic electron transport versus photon flux density. Generally longer, stronger sun exposures enhanced declines in both slope and maximum photosynthetic electron transport rates as well as photochemical efficiency of PSII and PSII/PSI more severely and prevented full recovery. Interestingly, increased NPQ capacity was accompanied by slower relaxation. This was more prominent in detached leaves with closed stomata, indicating that photorespiratory recycling of CO(2) provided little photoprotection to avocado shade leaves. Sun exposure of these shade leaves initiates a continuum of photoprotection, beyond full engagement of the Lx and V cycle in the antenna, but ultimately photoinactivated PSII reaction centers.

Decreased Photochemical Efficiency of Photosystem II following Sunlight Exposure of Shade-Grown Leaves of Avocado: Because of, or in Spite of, Two Kinetically Distinct Xanthophyll Cycles?1[W

PubMed Central

Jia, Husen; Förster, Britta; Chow, Wah Soon; Pogson, Barry James; Osmond, C. Barry

2013-01-01

This study resolved correlations between changes in xanthophyll pigments and photosynthetic properties in attached and detached shade-grown avocado (Persea americana) leaves upon sun exposure. Lutein epoxide (Lx) was deepoxidized to lutein (L), increasing the total pool by ΔL over 5 h, whereas violaxanthin (V) conversion to antheraxanthin (A) and zeaxanthin (Z) ceased after 1 h. During subsequent dark or shade recovery, de novo synthesis of L and Z continued, followed by epoxidation of A and Z but not of L. Light-saturated nonphotochemical quenching (NPQ) was strongly and linearly correlated with decreasing [Lx] and increasing [∆L] but showed a biphasic correlation with declining [V] and increasing [A+Z] separated when V deepoxidation ceased. When considering [ΔL+∆Z], the monophasic linear correlation was restored. Photochemical efficiency of photosystem II (PSII) and photosystem (PSI; deduced from the delivery of electrons to PSI in saturating single-turnover flashes) showed a strong correlation in their continuous decline in sunlight and an increase in NPQ capacity. This decrease was also reflected in the initial reduction of the slope of photosynthetic electron transport versus photon flux density. Generally longer, stronger sun exposures enhanced declines in both slope and maximum photosynthetic electron transport rates as well as photochemical efficiency of PSII and PSII/PSI more severely and prevented full recovery. Interestingly, increased NPQ capacity was accompanied by slower relaxation. This was more prominent in detached leaves with closed stomata, indicating that photorespiratory recycling of CO2 provided little photoprotection to avocado shade leaves. Sun exposure of these shade leaves initiates a continuum of photoprotection, beyond full engagement of the Lx and V cycle in the antenna, but ultimately photoinactivated PSII reaction centers. PMID:23213134

The Ratio of Leaf to Total Photosynthetic Area Influences Shade Survival and Plastic Response to Light of Green‐stemmed Leguminous Shrub Seedlings

PubMed Central

VALLADARES, FERNANDO; HERNÁNDEZ, LIBERTAD G.; DOBARRO, IKER; GARCÍA‐PÉREZ, CRISTINA; SANZ, RUBÉN; PUGNAIRE, FRANCISCO I.

2003-01-01

Different plant species and organs within a plant differ in their plastic response to light. These responses influence their performance and survival in relation to the light environment, which may range from full sunlight to deep shade. Plasticity, especially with regard to physiological features, is linked to a greater capacity to exploit high light and is usually low in shade‐tolerant species. Among photosynthetic organs, green stems, which represent a large fraction of the total photosynthetic area of certain species, are hypothesized to be less capable of adjustment to light than leaves, because of biomechanical and hydraulic constraints. The response to light by leaves and stems of six species of leguminous, green‐stemmed shrubs from dry and high‐light environments was studied by growing seedlings in three light environments: deep shade, moderate shade and sun (3, 30 and 100 % of full sunlight, respectively). Survival in deep shade ranged from 2 % in Retama sphaerocarpa to 74 % in Ulex europaeus. Survival was maximal at moderate shade in all species, ranging from 80 to 98 %. The six species differed significantly in their ratio of leaf to total photosynthetic area, which influenced their light response. Survival in deep shade increased significantly with increasing ratio of leaf to total photosynthetic area, and decreased with increasing plasticity in net photosynthesis and dark respiration. Responses to light differed between stems and leaves within each species. Mean phenotypic plasticity for the variables leaf or stem specific mass, chlorophyll content, chlorophyll a/b ratio, and carotenoid to chlorophyll ratio of leaves, was inversely related to that of stems. Although mean plasticity of stems increased with the ratio of leaf to total photosynthetic area, the mean plasticity of leaves decreased. Shrubs with green stems and a low ratio of leaf to total photosynthetic area are expected to be restricted to well‐lit habitats, at least during the seedling stage, owing to their inefficient light capture and the low plasticity of their stems. PMID:12646502

Sacramento's parking lot shading ordinance: environmental and economic costs of compliance

Treesearch

E.G. McPherson

2001-01-01

A survey of 15 Sacramento parking lots and computer modeling were used to evaluate parking capacity and compliance with the 1983 ordinance requiring 50% shade of paved areas (PA) 15 years after development. There were 6% more parking spaces than required by ordinance, and 36% were vacant during peak use periods. Current shade was 14% with 44% of this amount provided by...

Portrayal of tanning, clothing fashion and shade use in Australian women's magazines, 1987-2005.

PubMed

Dixon, Helen; Dobbinson, Suzanne; Wakefield, Melanie; Jamsen, Kris; McLeod, Kim

2008-10-01

To examine modelling of outcomes relevant to sun protection in Australian women's magazines, content analysis was performed on 538 spring and summer issues of popular women's magazines from 1987 to 2005. A total of 4949 full-colour images of Caucasian females were coded for depth of tan, extent of clothing cover, use of shade and setting. Logistic regression using robust standard errors to adjust for clustering on magazine was used to assess the relationship between these outcomes and year, setting and model's physical characteristics. Most models portrayed outdoors did not wear hats (89%) and were not in shade (87%). Between 1987 and 2005, the proportion of models depicted wearing hats decreased and the proportion of models portrayed with moderate to dark tans declined and then later increased. Younger women were more likely to be portrayed with a darker tan and more of their body exposed. Models with more susceptible phenotypes (paler hair and eye colour) were less likely to be depicted with a darker tan. Darker tans and poor sun-protective behaviour were most common among models depicted at beaches/pools. Implicit messages about sun protection in popular Australian women's magazines contradict public health messages concerning skin cancer prevention.

Characterization of cocoa production, income diversification and shade tree management along a climate gradient in Ghana.

PubMed

Abdulai, Issaka; Jassogne, Laurence; Graefe, Sophie; Asare, Richard; Van Asten, Piet; Läderach, Peter; Vaast, Philippe

2018-01-01

Reduced climatic suitability due to climate change in cocoa growing regions of Ghana is expected in the coming decades. This threatens farmers' livelihood and the cocoa sector. Climate change adaptation requires an improved understanding of existing cocoa production systems and farmers' coping strategies. This study characterized current cocoa production, income diversification and shade tree management along a climate gradient within the cocoa belt of Ghana. The objectives were to 1) compare existing production and income diversification between dry, mid and wet climatic regions, and 2) identify shade trees in cocoa agroforestry systems and their distribution along the climatic gradient. Our results showed that current mean cocoa yield level of 288kg ha-1yr-1 in the dry region was significantly lower than in the mid and wet regions with mean yields of 712 and 849 kg ha-1 yr-1, respectively. In the dry region, farmers diversified their income sources with non-cocoa crops and off-farm activities while farmers at the mid and wet regions mainly depended on cocoa (over 80% of annual income). Two shade systems classified as medium and low shade cocoa agroforestry systems were identified across the studied regions. The medium shade system was more abundant in the dry region and associated to adaptation to marginal climatic conditions. The low shade system showed significantly higher yield in the wet region but no difference was observed between the mid and dry regions. This study highlights the need for optimum shade level recommendation to be climatic region specific.

Characterization of cocoa production, income diversification and shade tree management along a climate gradient in Ghana

PubMed Central

Jassogne, Laurence; Graefe, Sophie; Asare, Richard; Van Asten, Piet; Läderach, Peter; Vaast, Philippe

2018-01-01

Reduced climatic suitability due to climate change in cocoa growing regions of Ghana is expected in the coming decades. This threatens farmers’ livelihood and the cocoa sector. Climate change adaptation requires an improved understanding of existing cocoa production systems and farmers’ coping strategies. This study characterized current cocoa production, income diversification and shade tree management along a climate gradient within the cocoa belt of Ghana. The objectives were to 1) compare existing production and income diversification between dry, mid and wet climatic regions, and 2) identify shade trees in cocoa agroforestry systems and their distribution along the climatic gradient. Our results showed that current mean cocoa yield level of 288kg ha-1yr-1 in the dry region was significantly lower than in the mid and wet regions with mean yields of 712 and 849 kg ha-1 yr-1, respectively. In the dry region, farmers diversified their income sources with non-cocoa crops and off-farm activities while farmers at the mid and wet regions mainly depended on cocoa (over 80% of annual income). Two shade systems classified as medium and low shade cocoa agroforestry systems were identified across the studied regions. The medium shade system was more abundant in the dry region and associated to adaptation to marginal climatic conditions. The low shade system showed significantly higher yield in the wet region but no difference was observed between the mid and dry regions. This study highlights the need for optimum shade level recommendation to be climatic region specific. PMID:29659629

Lutein from Deepoxidation of Lutein Epoxide Replaces Zeaxanthin to Sustain an Enhanced Capacity for Nonphotochemical Chlorophyll Fluorescence Quenching in Avocado Shade Leaves in the Dark1

PubMed Central

Förster, Britta; Pogson, Barry James; Osmond, Charles Barry

2011-01-01

Leaves of avocado (Persea americana) that develop and persist in deep shade canopies have very low rates of photosynthesis but contain high concentrations of lutein epoxide (Lx) that are partially deepoxidized to lutein (L) after 1 h of exposure to 120 to 350 μmol photons m−2 s−1, increasing the total L pool by 5% to 10% (ΔL). Deepoxidation of Lx to L was near stoichiometric and similar in kinetics to deepoxidation of violaxanthin (V) to antheraxanthin (A) and zeaxanthin (Z). Although the V pool was restored by epoxidation of A and Z overnight, the Lx pool was not. Depending on leaf age and pretreatment, the pool of ΔL persisted for up to 72 h in the dark. Metabolism of ΔL did not involve epoxidation to Lx. These contrasting kinetics enabled us to differentiate three states of the capacity for nonphotochemical chlorophyll fluorescence quenching (NPQ) in attached and detached leaves: ΔpH dependent (NPQΔpH) before deepoxidation; after deepoxidation in the presence of ΔL, A, and Z (NPQΔLAZ); and after epoxidation of A+Z but with residual ΔL (NPQΔL). The capacity of both NPQΔLAZ and NPQΔL was similar and 45% larger than NPQΔpH, but dark relaxation of NPQΔLAZ was slower. The enhanced capacity for NPQ was lost after metabolism of ΔL. The near equivalence of NPQΔLAZ and NPQΔL provides compelling evidence that the small dynamic pool ΔL replaces A+Z in avocado to “lock in” enhanced NPQ. The results are discussed in relation to data obtained with other Lx-rich species and in mutants of Arabidopsis (Arabidopsis thaliana) with increased L pools. PMID:21427278

[Measurement and comparison of the spectral transmittance of cerinate porcelain and human enamel].

PubMed

Chen, Ji-Hua; Zhou, Guo-Feng; Wei, Zhang-Rui; Wang, Hui; Zhao, San-Jun

2006-12-01

To measure the spectral transmittance of Cerinate porcelain veneer and enamel in different color and different thickness. Samples of Cerinate porcelain veneers were prepared in different thickness (0.50 mm, 0.75 mm, 1.00 mm) and different Vita shade (A1, A2, A3). Enamel samples in shade A2 were made with three thickness (0.50 mm, 0.75 mm, 1.00 mm). A spectrophotometer with spectra range (380-800 nm) was employed to measure the spectral transmittance. Spectral transmittance decreased with the increasing in the thickness of specimens and decreasing in the color darkness. The transmittance of Cerinate porcelain veneer material and enamel in the same color and same thickness hadn't significant difference. The key factor to spectral transmittance of porcelain veneer materials is veneer's thickness, and the color of the materials has also some influence on it. Cerinate porcelain veneers can properly recover the transparency of teeth.

Plant Strategies for Enhancing Access to Sunlight.

PubMed

Fiorucci, Anne-Sophie; Fankhauser, Christian

2017-09-11

Light is a vital resource for plants, which compete for it particularly in dense communities. Plants have multiple photosensory receptors to detect the presence of competitors and thereby adjust their growth and developmental strategies accordingly. Broadly speaking, plants fall into two categories depending on their response to shading by leaves: shade tolerant or shade avoiding. Here, we describe the photoperception mechanisms and the growth responses elicited by the neighboring vegetation in shade-avoiding plants, focusing on Arabidopsis thaliana, where these responses are best understood. The type of response depends on plant density, ranging from neighbor detection modulating growth in anticipation of future shading to the response to canopy shade where light resources are limiting. These diverse environments are sensed by various photoreceptors, and we will describe our current understanding of signal integration triggered by distinct light cues in diverse light conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Shaded Relief of Rio Sao Francisco, Brazil

NASA Technical Reports Server (NTRS)

2000-01-01

This topographic image acquired by SRTM shows an area south of the Sao Francisco River in Brazil. The scrub forest terrain shows relief of about 400 meters (1300 feet). Areas such as these are difficult to map by traditional methods because of frequent cloud cover and local inaccessibility. This region has little topographic relief, but even subtle changes in topography have far-reaching effects on regional ecosystems. The image covers an area of 57 km x 79 km and represents one quarter of the 225 km SRTM swath. Colors range from dark blue at water level to white and brown at hill tops. The terrain features that are clearly visible in this image include tributaries of the Sao Francisco, the dark-blue branch-like features visible from top right to bottom left, and on the left edge of the image, and hills rising up from the valley floor. The San Francisco River is a major source of water for irrigation and hydroelectric power. Mapping such regions will allow scientists to better understand the relationships between flooding cycles, forestation and human influences on ecosystems.

This shaded relief image was generated using topographic data from the Shuttle Radar Topography Mission. A computer-generated artificial light source illuminates the elevation data to produce a pattern of light and shadows. Slopes facing the light appear bright, while those facing away are shaded. On flatter surfaces, the pattern of light and shadows can reveal subtle features in the terrain. Shaded relief maps are commonly used in applications such as geologic mapping and land use planning.

The Shuttle Radar Topography Mission (SRTM), launched on February 11, 2000, uses the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. The mission is designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, an additional C-band imaging antenna and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA) and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Effect of light on growth, intracellular and extracellular pigment production by five pigment-producing filamentous fungi in synthetic medium.

PubMed

Velmurugan, Palanivel; Lee, Yong Hoon; Venil, Chidambaram Kulandaisamy; Lakshmanaperumalsamy, Perumalsamy; Chae, Jong-Chan; Oh, Byung-Taek

2010-04-01

The competence of the living creatures to sense and respond to light is well known. The effect of darkness and different color light quality on biomass, extracellular and intracellular pigment yield of five potent pigment producers Monascus purpureus, Isaria farinosa, Emericella nidulans, Fusarium verticillioides and Penicillium purpurogenum, with different color shades such as red, pink, reddish brown and yellow, were investigated. Incubation in total darkness increased the biomass, extracellular and intracellular pigment production in all the fungi. Extracellular red pigment produced by M. purpureus resulted maximum in darkness 36.75 + or - 2.1 OD and minimum in white unscreened light 5.90 + or - 1.1 OD. Similarly, intracellular red pigment produced by M. purpureus resulted maximum in darkness 18.27 + or - 0.9 OD/g and minimum in yellow light 8.03 + or - 0.6 OD/g of substrate. The maximum biomass production was also noticed in darkness 2.51 g/L and minimum in yellow light 0.5 g/L of dry weight. In contrast, growth of fungi in green and yellow wavelengths resulted in low biomass and pigment yield. It was found that darkness, (red 780-622 nm, blue 492-455 nm) and white light influenced pigment and biomass yield. Copyright 2009 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Influence of illuminants on the color distribution of shade guides.

PubMed

Park, Ji-Hoon; Lee, Yong-Keun; Lim, Bum-Soon

2006-12-01

Although a shade tab in a shade guide is matched to a natural tooth in the order of value, hue, and chroma, there are limited data on the color distribution of currently available shade guides sorted by these 3 parameters. Furthermore, spectrophotometric color measurements of shade tabs differ depending on the standard illuminant employed. The purpose of this study was to determine the color distributions of 2 shade guides in value (CIE L( *)), chroma (C( *)(ab)) and hue angle (h(o)) scale relative to the standard illuminants D(65), A, and F2. Color of shade tabs (n=36) from 2 shade guides (Vita Lumin and Chromascop) were measured, and the distributions for CIE L( *), C( *)(ab) and h(o) values were compared. Color differences of shade tabs depending on the illuminant were calculated. The distributions of the ratios of CIE L( *) and C( *)(ab) values of each shade tab compared with the lowest value tab or the lowest chroma tab were determined. The data for the value, chroma, and hue angle within each shade guide were analyzed with a 2-way ANOVA with the factors of shade designation and type of illuminant (alpha=.05). Color difference caused by change of illuminant was analyzed with a 2-way ANOVA with the factors of shade designation and pair of illuminants compared (alpha=.05). The Scheffe multiple comparison test was performed as a post hoc test. CIE L( *), C( *)(ab) and h(o) values were influenced by shade designation and type of illuminant in both shade guides. Color difference caused by change of the illuminant was influenced by the shade designation and pair of illuminants compared. The order of mean color differences of 16 Vita Lumin shade tabs by pairs of illuminants compared was as follows: DeltaE( *)(ab) (D(65)/F2) = 1.63 3.7). Color distribution of 2 shade guides by the value and chroma was not logical.

Conservation in Brazil's Chocolate Forest: The Unlikely Persistence of the Traditional Cocoa Agroecosystem.

PubMed

JOHNS

1999-01-01

/ In southern Bahia, Brazil, the traditional cocoa agroecosystem with a dense shade canopy of native trees is now recognized as a secondary conservation route for highly endangered Atlantic Rainforest species. This "chocolate forest" of the densely shaded farms persists despite a massive 20-year Brazilian government modernization program in which shade was seen as a chief impediment to raising cocoa production. The objective of this study was to determine how this traditional agroecosystem endured. Although dense shade limits cocoa yield, it provides several agroecological benefits: control of insect pests and weeds, microclimate stability, and soil fertility maintenance. A keycomponent of modernization efforts was a shade-tree removal program designed to maximize cocoa production by using low shade and fertilizer while substituting agrochemicals for many beneficial roles of the overhead trees. This research found that many farmers rejected, or only partially accepted, the shade reduction process although it promised much higher cocoa yield and profit. Farmers employing a wide range of shading were interviewed, and it was found that decisions to remove or maintain the shade trees were linked to both agroecological and risk-minimization factors. Farmers' perceptions of the agroecological functions of the shade trees and individual willingness to entertain the economic risk associated with substituting agrochemicals for these were important. A less-profitable, but lower-risk approach of occasional fertilizer and agrochemical use with the traditional shade intact was a rational and widespread choice. Policies designed to maintain the traditional agroecosystem through the current economic crisis should heed the multiple functions of the overhead trees. KEY WORDS: Conservation; Brazil; Atlantic Rainforest; Cocoa; Agroecology; Risk; Agroforestry

Partial shading of lateral branches affects growth, and foliage nitrogen- and water-use efficiencies in the conifer Cunninghamia lanceolata growing in a warm monsoon climate.

PubMed

Dong, Tingfa; Li, Junyu; Zhang, Yuanbin; Korpelainen, Helena; Niinemets, Ülo; Li, Chunyang

2015-06-01

The degree to which branches are autonomous in their acclimation responses to alteration in light environment is still poorly understood. We investigated the effects of shading of the sapling crown of Cunninghamia lanceolata (Lamb.) Hook on the whole-tree and mid-crown branch growth and current-year foliage structure and physiology. Four treatments providing 0, 50, 75 and 90% shading compared with full daylight (denoted as Treatment(0), Treatment(50%), Treatment(75%) and Treatment(90%), and Shaded(0), Shaded(50%), Shaded(75%) and Shaded(90%) for the shaded branches and Sunlit(0), Sunlit(50%), Sunlit(75%) and Sunlit(90%) for the opposite sunlit branches under natural light conditions, respectively), were applied over two consecutive growing seasons. Shading treatments decreased the growth of basal stem diameter, leaf dry mass per unit leaf area, stomatal conductance, transpiration rate, the ratio of water-soluble to structural leaf nitrogen content, photosynthetic nitrogen-use efficiency and instantaneous and long-term (estimated from carbon isotope composition) water-use efficiency in shaded branches. Differences between shaded and sunlit branches increased with increasing severity and duration of shading. A non-autonomous, partly compensatory behavior of non-shaded branches was observed for most traits, thus reflecting the dependence between the traits of sunlit branches and the severity of shading of the opposite crown half. The results collectively indicated that tree growth and branch and leaf acclimation responses of C. lanceolata are not only affected by the local light environment, but also by relative within-crown light conditions. We argue that such a non-autonomous branch response to changes in light conditions can improve whole-tree resource optimization. These results contribute to better understanding of tree growth and utilization of water and nitrogen under heterogeneous light conditions within tree canopies. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Partial Shade Stress Test for Thin-Film Photovoltaic Modules: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silverman, Timothy J.; Deceglie, Michael G.; Deline, Chris

2015-09-02

Partial shade of monolithic thin-film PV modules can cause reverse-bias conditions leading to permanent damage. In this work, we propose a partial shade stress test for thin-film PV modules that quantifies permanent performance loss. We designed the test with the aid of a computer model that predicts the local voltage, current and temperature stress that result from partial shade. The model predicts the module-scale interactions among the illumination pattern, the electrical properties of the photovoltaic material and the thermal properties of the module package. The test reproduces shading and loading conditions that may occur in the field. It accounts formore » reversible light-induced performance changes and for additional stress that may be introduced by light-enhanced reverse breakdown. We present simulated and experimental results from the application of the proposed test.« less

Modeling and simulation of the shading effect on the performance of a photovoltaic module in the presence of the bypass diode.

NASA Astrophysics Data System (ADS)

Zebiri, Mohamed; Mediouni, Mohamed; Idadoub, Hicham

2018-05-01

In photovoltaic renewable energy production systems where production is dependent on weather conditions, maintaining production at a suitable level is more than essential. The shading effect in photovoltaic panels affects the production of electrical energy by reducing it or even causing the destruction of some or all of the panels. To circumvent this problem, among the solutions proposed in the literature we find the use of by-pass diode and anti-return diode to minimize these consequences.In this paper we present a simulation under Matlab-Simulink of the shading effect and we compare the current voltages characteristics (I-V) and power voltage (P-V) of a photovoltaic system for different irradiations in the presence and absence of diode by -pass. For modeling, we will use the diode model and the Lambert W-function to solve the implicit equation of the output current. This method allows you to analyze the performance of a panel at different shading levels.

On Award to Crichton

NASA Astrophysics Data System (ADS)

Corbett, Kevin

2006-10-01

The recent Eos Forum article from the Council of the American Quaternary Association (AMQUA) attacking the American Association of Petroleum Geologists (AAPG)(Eos, 87(36), 364, 2006) goes beyond the pale of reasonable promotion or defense of AGU's position regarding global climate change and is a lamentable low for AGU in overarching political demagoguery. It is certainly within the purview of AGU to adopt a position concerning anthropogenic forcing of current global warming, as the association did in 2003. However, to challenge the competency, integrity, and intent of another scientific organization whose council and members read the data differently is truly reprehensible. The tone of the letter and AGU' position in promoting this view are nothing short of evangelical environmentalism with a dark shade of inquisitional environmental repression. Truly, the credibility, impartiality, and integrity of AGU are at question in the debate over climate science. Evidently, AMQUA believes its position to be so righteous that it should sit in judgment on all other professional scientific societies. Such a poorly reasoned and self-justifying position screams political bias.

Photosynthetic potential and accumulation of assimilates in the developing chloroembryos of Cyamposis tetragonoloba (L. ) Taub

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaladharan, P.; Vivekanandan, M.

1990-02-01

The photosynthetic potential of leaves and chloroembryos of Cyamopsis tetragonoloba (L.) Taub as measured by {sup 14}C-bicarbonate fixation, Hill activity, and in vivo fluorescence transients is compared. On a chlorophyll basis, dark fixation of NaH{sup 14}CO{sub 3} in chloroembryos was 1.5 times higher than that of the leaf, whereas carbon fixation under illumination was threefold higher in the leaf than in the embryos. Rates of O{sub 2} evolution were four times more in embryo than in leaf chloroplasts. Shading of developing fruits on the day of anthesis for 10 days induced a 65% reduction in dry matter accumulation in themore » etiolated embryos, as compared to the normal green embryos of the same fruit half covered by a transparent Polythene sheet. The reduction in dry weight, size of the embryos, and levels of assimilates after shading the developing fruits may be ascribed to partial autotrophy of the chloroembryos.« less

Uranus in True and False Color

NASA Image and Video Library

1996-08-01

These two pictures of Uranus -- one in true color (left) and the other in false color -- were compiled from images returned Jan. 17, 1986, by the narrow-angle camera of Voyager 2. The spacecraft was 9.1 million kilometers (5.7 million miles) from the planet, several days from closest approach. The picture at left has been processed to show Uranus as human eyes would see it from the vantage point of the spacecraft. The picture is a composite of images taken through blue, green and orange filters. The darker shadings at the upper right of the disk correspond to the day-night boundary on the planet. Beyond this boundary lies the hidden northern hemisphere of Uranus, which currently remains in total darkness as the planet rotates. The blue-green color results from the absorption of red light by methane gas in Uranus' deep, cold and remarkably clear atmosphere. The picture at right uses false color and extreme contrast enhancement to bring out subtle details in the polar region of Uranus. Images obtained through ultraviolet, violet and orange filters were respectively converted to the same blue, green and red colors used to produce the picture at left. The very slight contrasts visible in true color are greatly exaggerated here. In this false-color picture, Uranus reveals a dark polar hood surrounded by a series of progressively lighter concentric bands. One possible explanation is that a brownish haze or smog, concentrated over the pole, is arranged into bands by zonal motions of the upper atmosphere. The bright orange and yellow strip at the lower edge of the planet's limb is an artifact of the image enhancement. In fact, the limb is dark and uniform in color around the planet. http://photojournal.jpl.nasa.gov/catalog/PIA00032

ARC-1986-AC86-7009

NASA Image and Video Library

1986-01-17

Range : 9.1 million miles (5.7 million miles) P-29478C These two images pictures of Uranus, one in true color and the other in false color, were shot by Voyager 2's narrow angle camera. The picture at left has been processed to show Uranus as the human eye would see from the vantage point of the spacecraft. The image is a composite of shots taken through blue, green, and orange filters. The darker shadings on the upper right of the disk correspond to day-night boundaries on the planet. Beyond this boundary lies the hidden northern hemisphere of Uranus, which currently remains in total darkness as the planet rotates. The blue-green color results from the aborption of red light by methane gas in Uranus' deep, cold, and remarkably clear atmosphere. The picture at right uses false color and extreme contrast to bring out subtle details in the polar region of Uranus. Images obtained through ultraviolet, violet, and orange filters were respectively converted to the same blue, green, and red colors used to produce the picture at left. The very slight contrasts visible in true color are greatly exaggerated here. In this false colr picture, Uranus reveals a dark polar hood surrounded by aseries of progressively lighter concentric bands. One possible explanation is that a brownish haze or smog, concentrated around the pole, is arranged into bands of zonal motions of the upper atmosphere. Several artifacts of the optics and processing are visible. The occasional donut shapes are shadows cast by dust in the camera optics;the processing needed to bring ot faint features also bring out camera blemishes. in addition, the bright pink strip at the lower edge of the planets limb is an artifact of the image enhancement. In fact, the limb is dark and uniform in color around the planet.

Lutein from deepoxidation of lutein epoxide replaces zeaxanthin to sustain an enhanced capacity for nonphotochemical chlorophyll fluorescence quenching in avocado shade leaves in the dark.

PubMed

Förster, Britta; Pogson, Barry James; Osmond, Charles Barry

2011-05-01

Leaves of avocado (Persea americana) that develop and persist in deep shade canopies have very low rates of photosynthesis but contain high concentrations of lutein epoxide (Lx) that are partially deepoxidized to lutein (L) after 1 h of exposure to 120 to 350 μmol photons m(-2) s(-1), increasing the total L pool by 5% to 10% (ΔL). Deepoxidation of Lx to L was near stoichiometric and similar in kinetics to deepoxidation of violaxanthin (V) to antheraxanthin (A) and zeaxanthin (Z). Although the V pool was restored by epoxidation of A and Z overnight, the Lx pool was not. Depending on leaf age and pretreatment, the pool of ΔL persisted for up to 72 h in the dark. Metabolism of ΔL did not involve epoxidation to Lx. These contrasting kinetics enabled us to differentiate three states of the capacity for nonphotochemical chlorophyll fluorescence quenching (NPQ) in attached and detached leaves: ΔpH dependent (NPQ(ΔpH)) before deepoxidation; after deepoxidation in the presence of ΔL, A, and Z (NPQ(ΔLAZ)); and after epoxidation of A+Z but with residual ΔL (NPQ(ΔL)). The capacity of both NPQ(ΔLAZ) and NPQ(ΔL) was similar and 45% larger than NPQ(ΔpH), but dark relaxation of NPQ(ΔLAZ) was slower. The enhanced capacity for NPQ was lost after metabolism of ΔL. The near equivalence of NPQ(ΔLAZ) and NPQ(ΔL) provides compelling evidence that the small dynamic pool ΔL replaces A+Z in avocado to "lock in" enhanced NPQ. The results are discussed in relation to data obtained with other Lx-rich species and in mutants of Arabidopsis (Arabidopsis thaliana) with increased L pools.

Influence of Forest-Canopy Morphology and Relief on Spectral Characteristics of Taiga Forests

NASA Astrophysics Data System (ADS)

Zhirin, V. M.; Knyazeva, S. V.; Eydlina, S. P.

2017-12-01

The article deals with the results of a statistical analysis reflecting tendencies (trends) of the relationship between spectral characteristics of taiga forests, indicators of the morphological structure of forest canopy and illumination of the territory. The study was carried out on the example of the model forest territory of the Priangarskiy taiga region of Eastern Siberia (Krasnoyarsk krai) using historical data (forest inventory 1992, Landsat 5 TM 16.06.1989) and the digital elevation model. This article describes a method for determining the quantitative indicator of morphological structure of forest canopy based on taxation data, and the authors propose to subdivide the morphological structure into high complexity, medium complexity, and relatively simple. As a result of the research, dependences of average values of spectral brightness in near and short-wave infrared channels of a Landsat 5 TM image for dark-coniferous, light-coniferous and deciduous forests from the degree of complexity of the forest-canopy structure are received. A high level of variance and maximum brightness average values are marked in green moss (hilocominosa) dark-coniferous and various-grass (larioherbosa) dark-coniferous forests and light-coniferous forests with a complex structure of canopy. The parvifoliate forests are characterized by high values of brightness in stands with a relatively simple structure of the canopy and by a small variance in brightness of any degree of the structure of the canopy complexity. The increase in brightness for the lit slopes in comparison with shaded ones in all stands with a difficult morphological canopy structure is revealed. However, the brightness values of the lit and shaded slopes do not differ for stands with a medium complexity of the structure. It is noted that, in addition to the indicator of the forest-canopy structure, the possible impact on increasing the variance of spectral brightness for the taxation plot has a variability of the slope ratio of "microslopes" inside the forest plot if it exceeds 60%.

Translucency and masking ability of various composite resins at different thicknesses.

PubMed

Darabi, Farideh; Radafshar, Golpar; Tavangar, Maryam; Davaloo, Reza; Khosravian, Aref; Mirfarhadi, Nastaran

2014-09-01

Optical properties of the composite resins, concerning their translucency and thickness, are affected by discolored tooth structure or inherent darkness of the oral cavity. This study aimed to compare the translucency parameter (TP) of five different composite resins in different thicknesses and to evaluate their masking ability in black backgrounds. Five brands of composite resins; Gradia (GC) and Crystalline (Confi-dental) in opaque A2 (OA2), Vit-l-escence (Ultradent) in opaque snow (OS), Herculite XRV (Kerr) and Opallis (FGM) in dentin A2 (DA2) shades were selected to enroll the study. Color coordinates of each composite were determined at 0.5, 1, and 1.5 mm thicknesses on a white backing, the backing of material itself and a black backing were calculated by using a spectrophotometer to evaluate the translucency parameter (TP) of the study materials. The masking ability was also calculated from the specimens on the material itself and on black backing. The values under 2 were estimated as imperceptible. One-way ANOVA, T-test and Tukey HSD were employed for statistical analysis. The masking ability values, recorded for the 1.5 mm-thick specimens, were in the range of imperceptible except for the Herculite. There was no difference in TP values of the materials at 1.5 mm thickness. Opaque snow shade of Vit-l-escence and opaque A2 shade of Gradia showed lower TP values in comparison with the other 1 and 0.5 mm-thick materials and this difference was statistically significant (p< 0.05). In relatively thin thicknesses (≤1mm), these opaque/dentin shade composite resins could not mask the black background color.

Patients' perspective on dental aesthetics in a South-Eastern European community.

PubMed

Dudea, Diana; Lasserre, Jean-François; Alb, Camelia; Culic, Bogdan; Pop Ciutrila, Ioana Sofia; Colosi, Horatiu

2012-07-01

To assess the importance attributed to dental aesthetics by subjects from a Romanian community. In addition, the role played by dental color, the group-distributions based on the self-evaluation of dental color and the previous experience regarding whitening treatments are analysed. A multiple-choice questionnaire was administered to 540 patients in dental offices in Cluj-Napoca, Romania; the subjects were also asked to self-evaluate their dental shade, using a set of images as a comparison. Answers to the questionnaires were statistically analysed using Microsoft Excel and SPSS 13.00 (Pearson's chi-square test, Fisher's exact test, Kendall's tau b). From the participants, 17.96% were motivated by aesthetic reasons to ask for treatment; most of the patients evaluated their smile as "acceptable" (38.51%) or "having some defects" (29.44%) and were self-included in groups of medium and dark shades (33.7% and 33.89%, respectively). Whilst 22.40% of the subjects considered the dental color as being the most evident defect of their dentition, 39.07% indicated a self-perception of "an abnormal dental shade". A strong correlation between darker self-assessed tooth color-groups and the self-perception of an abnormal tooth color was found (Chi square p≪0.001, Kendall's tau-c=0.44, with p≪0.001). Previous whitening treatments were reported by 8.88% of the subjects. Among patients who wanted to improve one of their oral functions, the majority requested changes in aesthetics. Dental shade is one of the aspects recognized as problematic by the participants, but nonetheless the percentage of patients who had previously benefited by whitening treatments was moderate. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Effect of Luting Agents and Ceramic Thickness on the Color Variation of Different Ceramics against a Chromatic Background

PubMed Central

de Azevedo Cubas, Gloria Beatriz; Camacho, Guilherme Brião; Demarco, Flávio Fernando; Pereira-Cenci, Tatiana

2011-01-01

Objectives: The aim of this study was to assess the influence of various ceramic thicknesses and luting agents on color variation in five ceramic systems. Methods: Fifteen disc-shaped ceramic specimens (11 mm diameter; shade A3) were fabricated with each of the six veneering ceramics tested, with 1, 1.5, or 2 mm thickness (n=5). Resin composite discs (Z-250, shade C4) were used as bases to simulate a chromatic background. The cementation of the veneers was carried out with an opaque resin-based cement (Enforce, shade C4), a resin-based cement (Enforce, shade A3), or without cement (C4, control group). Color differences (ΔE*) were determined using a colorimeter. Three-way ANOVA was used to analyze the data, followed by a Tukey post-hoc test (α=.05). Results: The L*a*b* values of the ceramic systems were affected by both the luting agent and the ceramic thickness (P<.05). In general, there was no difference between the control group and the group using the resin-based cement. The use of an opaque luting agent resulted in an increase of the color coordinates a*, b*, L*, producing differences in ΔE* values for all ceramics tested, regardless of the thickness (P<.05). For the 2-mm thick veneers, higher values in the color parameters were obtained for all ceramics and were independent of the luting agent used. Conclusions: The association of 2-mm thickness with opaque cement presented the strongest masking ability of a dark colored background when compared to a non- opaque luting agent and the other thicknesses tested. PMID:21769264

Earthshots: Satellite images of environmental change – Lake Urmia, Iran

USGS Publications Warehouse

Adamson, Thomas

2015-01-01

The lake’s southern basin is shallower than its northern basin, so recent images show the water disappearing from the southern basin first. These Landsat images use the shortwave-infrared, near-infrared, and green wavelengths of light. Because water absorbs infrared light, water (dark blue to black) contrasts with the surrounding land areas. As the water becomes shallower, light is reflected off of the lakebed in shades of light blue. Lighter blue and bright areas immediately surrounding the lake are where the receding shoreline has exposed the lake bottom.

Photosynthesis, photoinhibition, and nitrogen use efficiency in native and invasive tree ferns in Hawaii.

PubMed

Durand, Leilani Z; Goldstein, Guillermo

2001-02-01

Photosynthetic gas exchange, chlorophyll fluorescence, nitrogen use efficiency, and related leaf traits of native Hawaiian tree ferns in the genus Cibotium were compared with those of the invasive Australian tree fern Sphaeropteris cooperi in an attempt to explain the higher growth rates of S. cooperi in Hawaii. Comparisons were made between mature sporophytes growing in the sun (gap or forest edge) and in shady understories at four sites at three different elevations. The invasive tree fern had 12-13 cm greater height increase per year and approximately 5 times larger total leaf surface area per plant compared to the native tree ferns. The maximum rates of photosynthesis of S. cooperi in the sun and shade were significantly higher than those of the native Cibotium spp (for example, 11.2 and 7.1 µmol m -2  s -1 , and 5.8 and 3.6 µmol m -2  s -1 respectively for the invasive and natives at low elevation). The instantaneous photosynthetic nitrogen use efficiency of the invasive tree fern was significantly higher than that of the native tree ferns, but when integrated over the life span of the frond the differences were not significant. The fronds of the invasive tree fern species had a significantly shorter life span than the native tree ferns (approximately 6 months and 12 months, respectively), and significantly higher nitrogen content per unit leaf mass. The native tree ferns growing in both sun and shade exhibited greater photoinhibition than the invasive tree fern after being experimentally subjected to high light levels. The native tree ferns recovered only 78% of their dark-acclimated quantum yield (F v /F m ), while the invasive tree fern recovered 90% and 86% of its dark-acclimated F v /F m when growing in sun and shade, respectively. Overall, the invasive tree fern appears to be more efficient at capturing and utilizing light than the native Cibotium species, particularly in high-light environments such as those associated with high levels of disturbance.

The Art of Being Flexible: How to Escape from Shade, Salt, and Drought1

PubMed Central

Pierik, Ronald; Testerink, Christa

2014-01-01

Environmental stresses, such as shading of the shoot, drought, and soil salinity, threaten plant growth, yield, and survival. Plants can alleviate the impact of these stresses through various modes of phenotypic plasticity, such as shade avoidance and halotropism. Here, we review the current state of knowledge regarding the mechanisms that control plant developmental responses to shade, salt, and drought stress. We discuss plant hormones and cellular signaling pathways that control shoot branching and elongation responses to shade and root architecture modulation in response to drought and salinity. Because belowground stresses also result in aboveground changes and vice versa, we then outline how a wider palette of plant phenotypic traits is affected by the individual stresses. Consequently, we argue for a research agenda that integrates multiple plant organs, responses, and stresses. This will generate the scientific understanding needed for future crop improvement programs aiming at crops that can maintain yields under variable and suboptimal conditions. PMID:24972713

The dark side of gloss.

PubMed

Kim, Juno; Marlow, Phillip J; Anderson, Barton L

2012-11-01

Our visual system relies on the image structure generated by the interaction of light with objects to infer their material properties. One widely studied surface property is gloss, which can provide information that an object is smooth, shiny or wet. Studies have historically focused on the role of specular highlights in modulating perceived gloss. Here we show in human observers that glossy surfaces can generate both bright specular highlights and dark specular 'lowlights', and that the presence of either is sufficient to generate compelling percepts of gloss. We show that perceived gloss declines when the image structure generated by specular lowlights is blurred or misaligned with surrounding surface shading and that perceived gloss can arise from the presence of lowlights in surface regions isolated from highlights. These results suggest that the image structure generated by specular highlights and lowlights is used to construct our experience of surface gloss.

Snake velvet black: Hierarchical micro- and nanostructure enhances dark colouration in Bitis rhinoceros

NASA Astrophysics Data System (ADS)

Spinner, Marlene; Kovalev, Alexander; Gorb, Stanislav N.; Westhoff, Guido

2013-05-01

The West African Gaboon viper (Bitis rhinoceros) is a master of camouflage due to its colouration pattern. Its skin is geometrically patterned and features black spots that purport an exceptional spatial depth due to their velvety surface texture. Our study shades light on micromorphology, optical characteristics and principles behind such a velvet black appearance. We revealed a unique hierarchical pattern of leaf-like microstructures striated with nanoridges on the snake scales that coincides with the distribution of black colouration. Velvet black sites demonstrate four times lower reflectance and higher absorbance than other scales in the UV - near IR spectral range. The combination of surface structures impeding reflectance and absorbing dark pigments, deposited in the skin material, provides reflecting less than 11% of the light reflected by a polytetrafluoroethylene diffuse reflectance standard in any direction. A view-angle independent black structural colour in snakes is reported here for the first time.

Snake velvet black: hierarchical micro- and nanostructure enhances dark colouration in Bitis rhinoceros.

PubMed

Spinner, Marlene; Kovalev, Alexander; Gorb, Stanislav N; Westhoff, Guido

2013-01-01

The West African Gaboon viper (Bitis rhinoceros) is a master of camouflage due to its colouration pattern. Its skin is geometrically patterned and features black spots that purport an exceptional spatial depth due to their velvety surface texture. Our study shades light on micromorphology, optical characteristics and principles behind such a velvet black appearance. We revealed a unique hierarchical pattern of leaf-like microstructures striated with nanoridges on the snake scales that coincides with the distribution of black colouration. Velvet black sites demonstrate four times lower reflectance and higher absorbance than other scales in the UV-near IR spectral range. The combination of surface structures impeding reflectance and absorbing dark pigments, deposited in the skin material, provides reflecting less than 11% of the light reflected by a polytetrafluoroethylene diffuse reflectance standard in any direction. A view-angle independent black structural colour in snakes is reported here for the first time.

Reverse bias protected solar array with integrated bypass battery

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A (Inventor)

2012-01-01

A method for protecting the photovoltaic cells in a photovoltaic (PV) array from reverse bias damage by utilizing a rechargeable battery for bypassing current from a shaded photovoltaic cell or group of cells, avoiding the need for a bypass diode. Further, the method mitigates the voltage degradation of a PV array caused by shaded cells.

SRTM Colored Height and Shaded Relief: Near Zapala, Argentina

NASA Technical Reports Server (NTRS)

2001-01-01

Topographic data provided by the Shuttle Radar Topography Mission can provide many clues to geologic history and processes. This view of an area southwest of Zapala, Argentina, shows a wide diversity of geologic features. The highest peaks (left) appear to be massive (un-layered)crystalline rocks, perhaps granites. To their right (eastward) are tilted and eroded layered rocks, perhaps old lava flows, forming prominent ridges. Farther east and south, more subtle and curvilinear ridges show that the rock layers have not only been tilted but also folded. At the upper right, plateaus that cap the underlying geologic complexities are more recent lava flows - younger than the folding, but older than the current erosional pattern. Landforms in the southeast (lower right) and south-central areas appear partially wind sculpted.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark, as would be the case at noon at this latitude in the southern hemisphere. Color-coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard Space Shuttle Endeavour, launched on February 11,2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar that flew twice on Space Shuttle Endeavour in 1994. Shuttle Radar Topography Mission was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration, the National Imagery and Mapping Agency of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Size: 45.9 by 36.0 kilometers ( 28.5 by 22.3 miles) Location: 39.4 deg. South lat., 70.3 deg. West lon. Orientation: North toward the top Image Data: Shaded and colored Shuttle Radar Topography Mission elevation model Date Acquired: February 2000

High Performance CMOS Light Detector with Dark Current Suppression in Variable-Temperature Systems.

PubMed

Lin, Wen-Sheng; Sung, Guo-Ming; Lin, Jyun-Long

2016-12-23

This paper presents a dark current suppression technique for a light detector in a variable-temperature system. The light detector architecture comprises a photodiode for sensing the ambient light, a dark current diode for conducting dark current suppression, and a current subtractor that is embedded in the current amplifier with enhanced dark current cancellation. The measured dark current of the proposed light detector is lower than that of the epichlorohydrin photoresistor or cadmium sulphide photoresistor. This is advantageous in variable-temperature systems, especially for those with many infrared light-emitting diodes. Experimental results indicate that the maximum dark current of the proposed current amplifier is approximately 135 nA at 125 °C, a near zero dark current is achieved at temperatures lower than 50 °C, and dark current and temperature exhibit an exponential relation at temperatures higher than 50 °C. The dark current of the proposed light detector is lower than 9.23 nA and the linearity is approximately 1.15 μA/lux at an external resistance R SS = 10 kΩ and environmental temperatures from 25 °C to 85 °C.

High Performance CMOS Light Detector with Dark Current Suppression in Variable-Temperature Systems

PubMed Central

Lin, Wen-Sheng; Sung, Guo-Ming; Lin, Jyun-Long

2016-01-01

This paper presents a dark current suppression technique for a light detector in a variable-temperature system. The light detector architecture comprises a photodiode for sensing the ambient light, a dark current diode for conducting dark current suppression, and a current subtractor that is embedded in the current amplifier with enhanced dark current cancellation. The measured dark current of the proposed light detector is lower than that of the epichlorohydrin photoresistor or cadmium sulphide photoresistor. This is advantageous in variable-temperature systems, especially for those with many infrared light-emitting diodes. Experimental results indicate that the maximum dark current of the proposed current amplifier is approximately 135 nA at 125 °C, a near zero dark current is achieved at temperatures lower than 50 °C, and dark current and temperature exhibit an exponential relation at temperatures higher than 50 °C. The dark current of the proposed light detector is lower than 9.23 nA and the linearity is approximately 1.15 μA/lux at an external resistance RSS = 10 kΩ and environmental temperatures from 25 °C to 85 °C. PMID:28025530

Shade-grown coffee in Puerto Rico: Opportunities to preserve biodiversity while reinvigorating a struggling agricultural commodity

USGS Publications Warehouse

Borkhataria, R.; Collazo, J.A.; Groom, Martha J.; Jordan-Garcia, A.

2012-01-01

Shade-grown coffee contributes to biodiversity conservation and has many ecological benefits. We reviewed historical trends in coffee production and interviewed 100 coffee growers in 1999 to determine current management practices and attitudes toward the cultivation of sun and shade coffee in Puerto Rico. We discuss the outlook for the coffee industry in the 21st century and implications for biodiversity conservation, hoping lessons from Puerto Rico will apply to the international coffee industry. Throughout the 20th century, government intervention, including subsidies and technical assistance, supported coffee farming in Puerto Rico. In an effort to modernize coffee production and increase yields, the conversion from shade to sun coffee plantations was encouraged. Despite government support, the amount of land devoted to this once dominant agricultural commodity declined markedly between 1982 and 2007 (84%), due to labor shortages, low income, and catastrophic hurricanes. We found that a return to shaded plantations would be embraced by most farmers. Growers of shaded coffee were generally happier with their cultivation practices (89.3% satisfied) than growers of sun coffee (60.9% satisfied), valued biodiversity, and were willing to cultivate coffee under shade if given similar incentives to those received for farming sun coffee. The future of the coffee industry in Puerto Rico may depend on government programs that capitalize upon emerging markets for sustainably produced, shade-grown coffee. We conclude that where governments have close ties to the coffee industry, they should strive to wed economic development with the conservation of biodiversity and associated ecological services by providing support and incentives for the production of shade coffee. ?? 2011 Elsevier B.V.

Reduction of front-metallization grid shading in concentrator cells through laser micro-grooved cover glass

DOE Office of Scientific and Technical Information (OSTI.GOV)

García-Linares, Pablo, E-mail: pablo.garcia-linares@cea.fr; Voarino, Philippe; Besson, Pierre

2015-09-28

Concentrator solar cell front-grid metallizations are designed so that the trade-off between series resistance and shading factor (SF) is optimized for a particular irradiance. High concentrator photovoltaics (CPV) typically requires a metallic electrode pattern that covers up to 10% of the cell surface. The shading effect produced by this front electrode results in a significant reduction in short-circuit current (I{sub SC}) and hence, in a significant efficiency loss. In this work we present a cover glass (originally meant to protect the cell surface) that is laser-grooved with a micrometric pattern that redirects the incident solar light towards interfinger regions andmore » away from the metallic electrodes, where they would be wasted in terms of photovoltaic generation. Quantum efficiency (QE) and current (I)-voltage (V) characterization under concentration validate the proof-of-concept, showing great potential for CPV applications.« less

Group selection - problems and possibilities and for the more shade-intolerant species

Treesearch

Paul A. Murphy; Michael G. Shelton; David L. Graney

1993-01-01

The group selection method is a hybrid, drawing key elements from both even- and uneven-aged silviculture. It is perhaps the least used and understood of all the reproductive cutting methods, but it is gaining popularity because of the current disfavor of even-aged silviculture. The group selection method appears promising for regenerating shade-intolerant and...

Group selection - problems and possibilities and for the more shade-intolerant species

Treesearch

Paul A. Murphy; Michael G. Shelton; David L. Graney

1993-01-01

The group selection method is a hybrid, drawing key elements from both even- and uneven-aged silviculture. It is perhaps the least used and understood of all reproductive cutting methods, but it is gaining popularity because of the current disfavor of even-aged silviculture. The group selection method appears promising for regenerating shade-intolerant and intermediate...

Improving detection tools for the emerald ash borer (Coleoptera: Buprestidae): comparison of prism and multifunnel traps at varying population densities.

PubMed

Francese, Joseph A; Rietz, Michael L; Crook, Damon J; Fraser, Ivich; Lance, David R; Mastro, Victor C

2013-12-01

The current emerald ash borer survey trap used in the United States is a prism trap constructed from a stock purple corrugated plastic. In recent years, several colors (particularly shades of green and purple) have been shown to be more attractive to the emerald ash borer than this stock color. Our goal was to determine if plastics produced with these colors and incorporated into prism traps can improve and serve as a new alternative to plastics already in use for the emerald ash borer survey. The plastics were tested in moderate to heavily infested areas in Michigan in two initial studies to test their effectiveness at catching the emerald ash borer. Because results from studies performed in heavily infested sites may not always correspond with what is found along the edges of the infestation, we compared trap catch and detection rates (recording at least one catch on a trap over the course of the entire trapping season) of several trap types and colors at sites outside the core of the currently known emerald ash borer infestation in a nine-state detection tool comparison study. Two of the new plastics, a (Sabic) purple and a medium-dark (Sabic) green were incorporated into prism traps and tested alongside a standard purple prism trap and a green multifunnel trap. In areas with lower emerald ash borer density, the new purple (Sabic) corrugated plastic caught more beetles than the current purple prism trap, as well as more than the medium-dark green (Sabic) prism and green multifunnel traps. Sabic purple traps in the detection tools comparison study recorded a detection rate of 86% compared with 73, 66, and 58% for the standard purple, Sabic green, and green multifunnel traps, respectively. These detection rates were reduced to 80, 63, 55, and 46%, respectively, at low emerald ash borer density sites.

Calculating the Effect of External Shading on the Solar Heat Gain Coefficient of Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kohler, Christian; Shukla, Yash; Rawal, Rajan

Current prescriptive building codes have limited ways to account for the effect of solar shading, such as overhangs and awnings, on window solar heat gains. We propose two new indicators, the adjusted Solar Heat Gain Coefficient (aSHGC) which accounts for external shading while calculating the SHGC of a window, and a weighted SHGC (SHGCw) which provides a seasonal SHGC weighted by solar intensity. We demonstrate a method to calculate these indices using existing tools combined with additional calculations. The method is demonstrated by calculating the effect of an awning on a clear double glazing in New Delhi.

Unravelling the nocturnal appearance of bogue Boops boops shoals in the anthropogenically modified shallow littoral.

PubMed

Mavraki, N; Georgiadis, M; Koutsikopoulos, C; Tzanatos, E

2016-05-01

In the present study the role of the nocturnal migration of bogue Boops boops shoals to anthropogenically modified shallow littoral locations was examined, evaluating four alternative hypotheses: (1) feeding, (2) reproduction, (3) attraction of B. boops to artificial light and (4) concealment in the darkness related to predation avoidance. All hypotheses apart from predation avoidance were rejected, as B. boops tended to concentrate in shaded locations of wider illuminated areas, a finding not only important concerning fish behaviour, but also with significant management implications. © 2016 The Fisheries Society of the British Isles.

Damage in Monolithic Thin-Film Photovoltaic Modules Due to Partial Shade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silverman, Timothy J.; Mansfield, Lorelle; Repins, Ingrid

2016-09-01

The typical configuration of monolithic thin-film photovoltaic modules makes it possible for partial shade to place one or more cells in such a module in reverse bias. Reverse bias operation leads to high voltage, current density, and power density conditions, which can act as driving forces for failure. We showed that a brief outdoor shadow event can cause a 7% permanent loss in power. We applied an indoor partial shade durability test that moves beyond the standard hot spot endurance test by using more realistic mask and bias conditions and by carefully quantifying the permanent change in performance due tomore » the stress. With the addition of a pass criterion based on change in maximum power, this procedure will soon be proposed as a part of the module-type qualification test. All six commercial copper indium gallium diselenide and cadmium telluride modules we tested experienced permanent damage due to the indoor partial shade test, ranging from 4% to 14% loss in maximum power. We conclude by summarizing ways to mitigate partial shade stress at the cell, module, and system levels.« less

Computation of dark frames in digital imagers

NASA Astrophysics Data System (ADS)

Widenhorn, Ralf; Rest, Armin; Blouke, Morley M.; Berry, Richard L.; Bodegom, Erik

2007-02-01

Dark current is caused by electrons that are thermally exited into the conduction band. These electrons are collected by the well of the CCD and add a false signal to the chip. We will present an algorithm that automatically corrects for dark current. It uses a calibration protocol to characterize the image sensor for different temperatures. For a given exposure time, the dark current of every pixel is characteristic of a specific temperature. The dark current of every pixel can therefore be used as an indicator of the temperature. Hot pixels have the highest signal-to-noise ratio and are the best temperature sensors. We use the dark current of a several hundred hot pixels to sense the chip temperature and predict the dark current of all pixels on the chip. Dark current computation is not a new concept, but our approach is unique. Some advantages of our method include applicability for poorly temperature-controlled camera systems and the possibility of ex post facto dark current correction.

Prediction of large negative shaded-side spacecraft potentials

NASA Technical Reports Server (NTRS)

Prokopenko, S. M. L.; Laframboise, J. G.

1977-01-01

A calculation by Knott, for the floating potential of a spherically symmetric synchronous-altitude satellite in eclipse, was adapted to provide simple calculations of upper bounds on negative potentials which may be achieved by electrically isolated shaded surfaces on spacecraft in sunlight. Large (approximately 60 percent) increases in predicted negative shaded-side potentials are obtained. To investigate effective potential barrier or angular momentum selection effects due to the presence of less negative sunlit-side or adjacent surface potentials, these expressions were replaced by the ion random current, which is a lower bound for convex surfaces when such effects become very severe. Further large increases in predicted negative potentials were obtained, amounting to a doubling in some cases.

Space Radar Image of Moscow, Russia

NASA Image and Video Library

1999-05-01

This is a vertically polarized L-band image of the southern half of Moscow, an area which has been inhabited for 2,000 years. The image covers a diameter of approximately 50 kilometers (31 miles) and was taken on September 30, 1994 by the Spaceborne Imaging Radar-C/X-band Synthetic Aperture Radar aboard the space shuttle Endeavour. The city of Moscow was founded about 750 years ago and today is home to about 8 million residents. The southern half of the circular highway (a road that looks like a ring) can easily be identified as well as the roads and railways radiating out from the center of the city. The city was named after the Moskwa River and replaced Russia's former capital, St. Petersburg, after the Russian Revolution in 1917. The river winding through Moscow shows up in various gray shades. The circular structure of many city roads can easily be identified, although subway connections covering several hundred kilometers are not visible in this image. The white areas within the ring road and outside of it are buildings of the city itself and it suburban towns. Two of many airports are located in the west and southeast of Moscow, near the corners of the image. The Kremlin is located north just outside of the imaged city center. It was actually built in the 16th century, when Ivan III was czar, and is famous for its various churches. In the surrounding area, light gray indicates forests, while the dark patches are agricultural areas. The various shades from middle gray to dark gray indicate different stages of harvesting, ploughing and grassland. http://photojournal.jpl.nasa.gov/catalog/PIA01752

The Photochemical Reflectance Index from Directional Cornfield Reflectances: Observations and Simulations

NASA Technical Reports Server (NTRS)

Cheng, Yen-Ben; Middleton, Elizabeth M.; Zhang, Qingyuan; Corp, Lawrence A.; Dandois, Jonathan; Kustas, William P.

2012-01-01

The two-layer Markov chain Analytical Canopy Reflectance Model (ACRM) was linked with in situ hyperspectral leaf optical properties to simulate the Photochemical Reflectance Index (PRI) for a corn crop canopy at three different growth stages. This is an extended study after a successful demonstration of PRI simulations for a cornfield previously conducted at an early vegetative growth stage. Consistent with previous in situ studies, sunlit leaves exhibited lower PRI values than shaded leaves. Since sunlit (shaded) foliage dominates the canopy in the reflectance hotspot (coldspot), the canopy PRI derived from field hyperspectral observations displayed sensitivity to both view zenith angle and relative azimuth angle at all growth stages. Consequently, sunlit and shaded canopy sectors were most differentiated when viewed along the azimuth matching the solar principal plane. These directional PRI responses associated with sunlit/shaded foliage were successfully reproduced by the ACRM. As before, the simulated PRI values from the current study were closer to in situ values when both sunlit and shaded leaves were utilized as model input data in a two-layer mode, instead of a one-layer mode with sunlit leaves only. Model performance as judged by correlation between in situ and simulated values was strongest for the mature corn crop (r = 0.87, RMSE = 0.0048), followed by the early vegetative stage (r = 0.78; RMSE = 0.0051) and the early senescent stage (r = 0.65; RMSE = 0.0104). Since the benefit of including shaded leaves in the scheme varied across different growth stages, a further analysis was conducted to investigate how variable fractions of sunlit/shaded leaves affect the canopy PRI values expected for a cornfield, with implications for 20 remote sensing monitoring options. Simulations of the sunlit to shaded canopy ratio near 50/50 +/- 10 (e.g., 60/40) matching field observations at all growth stages were examined. Our results suggest in the importance of the sunlit/shaded fraction and canopy structure in understanding and interpreting PRI.

Shade compromises the photosynthetic efficiency of NADP-ME less than that of PEP-CK and NAD-ME C4 grasses.

PubMed

Sonawane, Balasaheb V; Sharwood, Robert E; Whitney, Spencer; Ghannoum, Oula

2018-05-25

The high energy cost and apparently low plasticity of C4 photosynthesis compared with C3 photosynthesis may limit the productivity and distribution of C4 plants in low light (LL) environments. C4 photosynthesis evolved numerous times, but it remains unclear how different biochemical subtypes perform under LL. We grew eight C4 grasses belonging to three biochemical subtypes [NADP-malic enzyme (NADP-ME), NAD-malic enzyme (NAD-ME), and phosphoenolpyruvate carboxykinase (PEP-CK)] under shade (16% sunlight) or control (full sunlight) conditions and measured their photosynthetic characteristics at both low and high light. We show for the first time that LL (during measurement or growth) compromised the CO2-concentrating mechanism (CCM) to a greater extent in NAD-ME than in PEP-CK or NADP-ME C4 grasses by virtue of a greater increase in carbon isotope discrimination (∆P) and bundle sheath CO2 leakiness (ϕ), and a greater reduction in photosynthetic quantum yield (Φmax). These responses were partly explained by changes in the ratios of phosphoenolpyruvate carboxylase (PEPC)/initial Rubisco activity and dark respiration/photosynthesis (Rd/A). Shade induced a greater photosynthetic acclimation in NAD-ME than in NADP-ME and PEP-CK species due to a greater Rubisco deactivation. Shade also reduced plant dry mass to a greater extent in NAD-ME and PEP-CK relative to NADP-ME grasses. In conclusion, LL compromised the co-ordination of the C4 and C3 cycles and, hence, the efficiency of the CCM to a greater extent in NAD-ME than in PEP-CK species, while CCM efficiency was less impacted by LL in NADP-ME species. Consequently, NADP-ME species are more efficient at LL, which could explain their agronomic and ecological dominance relative to other C4 grasses.

Shade compromises the photosynthetic efficiency of NADP-ME less than that of PEP-CK and NAD-ME C4 grasses

PubMed Central

2018-01-01

Abstract The high energy cost and apparently low plasticity of C4 photosynthesis compared with C3 photosynthesis may limit the productivity and distribution of C4 plants in low light (LL) environments. C4 photosynthesis evolved numerous times, but it remains unclear how different biochemical subtypes perform under LL. We grew eight C4 grasses belonging to three biochemical subtypes [NADP-malic enzyme (NADP-ME), NAD-malic enzyme (NAD-ME), and phosphoenolpyruvate carboxykinase (PEP-CK)] under shade (16% sunlight) or control (full sunlight) conditions and measured their photosynthetic characteristics at both low and high light. We show for the first time that LL (during measurement or growth) compromised the CO2-concentrating mechanism (CCM) to a greater extent in NAD-ME than in PEP-CK or NADP-ME C4 grasses by virtue of a greater increase in carbon isotope discrimination (∆P) and bundle sheath CO2 leakiness (ϕ), and a greater reduction in photosynthetic quantum yield (Φmax). These responses were partly explained by changes in the ratios of phosphoenolpyruvate carboxylase (PEPC)/initial Rubisco activity and dark respiration/photosynthesis (Rd/A). Shade induced a greater photosynthetic acclimation in NAD-ME than in NADP-ME and PEP-CK species due to a greater Rubisco deactivation. Shade also reduced plant dry mass to a greater extent in NAD-ME and PEP-CK relative to NADP-ME grasses. In conclusion, LL compromised the co-ordination of the C4 and C3 cycles and, hence, the efficiency of the CCM to a greater extent in NAD-ME than in PEP-CK species, while CCM efficiency was less impacted by LL in NADP-ME species. Consequently, NADP-ME species are more efficient at LL, which could explain their agronomic and ecological dominance relative to other C4 grasses. PMID:29659931

The trehalose pathway in maize: conservation and gene regulation in response to the diurnal cycle and extended darkness

PubMed Central

Henry, Clémence; Bledsoe, Samuel W.; Siekman, Allison; Kollman, Alec; Waters, Brian M.; Feil, Regina; Stitt, Mark; Lagrimini, L. Mark

2014-01-01

Energy resources in plants are managed in continuously changing environments, such as changes occurring during the day/night cycle. Shading is an environmental disruption that decreases photosynthesis, compromises energy status, and impacts on crop productivity. The trehalose pathway plays a central but not well-defined role in maintaining energy balance. Here, we characterized the maize trehalose pathway genes and deciphered the impacts of the diurnal cycle and disruption of the day/night cycle on trehalose pathway gene expression and sugar metabolism. The maize genome encodes 14 trehalose-6-phosphate synthase (TPS) genes, 11 trehalose-6-phosphate phosphatase (TPP) genes, and one trehalase gene. Transcript abundance of most of these genes was impacted by the day/night cycle and extended dark stress, as were sucrose, hexose sugars, starch, and trehalose-6-phosphate (T6P) levels. After extended darkness, T6P levels inversely followed class II TPS and sucrose non-fermenting-related protein kinase 1 (SnRK1) target gene expression. Most significantly, T6P no longer tracked sucrose levels after extended darkness. These results showed: (i) conservation of the trehalose pathway in maize; (ii) that sucrose, hexose, starch, T6P, and TPS/TPP transcripts respond to the diurnal cycle; and(iii) that extended darkness disrupts the correlation between T6P and sucrose/hexose pools and affects SnRK1 target gene expression. A model for the role of the trehalose pathway in sensing of sucrose and energy status in maize seedlings is proposed. PMID:25271261

SHADE: A Shape-Memory-Activated Device Promoting Ankle Dorsiflexion

NASA Astrophysics Data System (ADS)

Pittaccio, S.; Viscuso, S.; Rossini, M.; Magoni, L.; Pirovano, S.; Villa, E.; Besseghini, S.; Molteni, F.

2009-08-01

Acute post-stroke rehabilitation protocols include passive mobilization as a means to prevent contractures. A device (SHADE) that provides repetitive passive motion to a flaccid ankle by using shape memory alloy actuators could be of great help in providing this treatment. A suitable actuator was designed as a cartridge of approximately 150 × 20 × 15 mm, containing 2.5 m of 0.25 mm diameter NiTi wire. This actuator was activated by Joule’s effect employing a 7 s current input at 0.7 A, which provided 10 N through 76 mm displacement. Cooling and reset by natural convection took 30 s. A prototype of SHADE was assembled with two thermoplastic shells hinged together at the ankle and strapped on the shin and foot. Two actuators were fixed on the upper shell while an inextensible thread connected each NiTi wire to the foot shell. The passive ankle motion (passive range of motion, PROM) generated by SHADE was evaluated optoelectronically on three flaccid patients (58 ± 5 years old); acceptability was assessed by a questionnaire presented to further three flaccid patients (44 ± 11.5 years old) who used SHADE for 5 days, 30 min a day. SHADE was well accepted by all patients, produced good PROM, and caused no pain. The results prove that suitable limb mobilization can be produced by SMA actuators.

Dark Current Degradation of Near Infrared Avalanche Photodiodes from Proton Irradiation

NASA Technical Reports Server (NTRS)

Becker, Heidi N.; Johnston, Allan H.

2004-01-01

InGaAs and Ge avalanche photodiodes (APDs) are examined for the effects of 63-MeV protons on dark current. Dark current increases were large and similar to prior results for silicon APDs, despite the smaller size of InGaAs and Ge devices. Bulk dark current increases from displacement damage in the depletion regions appeared to be the dominant contributor to overall dark current degradation. Differences in displacement damage factors are discussed as they relate to structural and material differences between devices.

Color difference thresholds in dentistry.

PubMed

Paravina, Rade D; Ghinea, Razvan; Herrera, Luis J; Bona, Alvaro D; Igiel, Christopher; Linninger, Mercedes; Sakai, Maiko; Takahashi, Hidekazu; Tashkandi, Esam; Perez, Maria del Mar

2015-01-01

The aim of this prospective multicenter study was to determine 50:50% perceptibility threshold (PT) and 50:50% acceptability threshold (AT) of dental ceramic under simulated clinical settings. The spectral radiance of 63 monochromatic ceramic specimens was determined using a non-contact spectroradiometer. A total of 60 specimen pairs, divided into 3 sets of 20 specimen pairs (medium to light shades, medium to dark shades, and dark shades), were selected for psychophysical experiment. The coordinating center and seven research sites obtained the Institutional Review Board (IRB) approvals prior the beginning of the experiment. Each research site had 25 observers, divided into five groups of five observers: dentists-D, dental students-S, dental auxiliaries-A, dental technicians-T, and lay persons-L. There were 35 observers per group (five observers per group at each site ×7 sites), for a total of 175 observers. Visual color comparisons were performed using a viewing booth. Takagi-Sugeno-Kang (TSK) fuzzy approximation was used for fitting the data points. The 50:50% PT and 50:50% AT were determined in CIELAB and CIEDE2000. The t-test was used to evaluate the statistical significance in thresholds differences. The CIELAB 50:50% PT was ΔEab  = 1.2, whereas 50:50% AT was ΔEab  = 2.7. Corresponding CIEDE2000 (ΔE00 ) values were 0.8 and 1.8, respectively. 50:50% PT by the observer group revealed differences among groups D, A, T, and L as compared with 50:50% PT for all observers. The 50:50% AT for all observers was statistically different than 50:50% AT in groups T and L. A 50:50% perceptibility and ATs were significantly different. The same is true for differences between two color difference formulas ΔE00 /ΔEab . Observer groups and sites showed high level of statistical difference in all thresholds. Visual color difference thresholds can serve as a quality control tool to guide the selection of esthetic dental materials, evaluate clinical performance, and interpret visual and instrumental findings in clinical dentistry, dental research, and subsequent standardization. The importance of quality control in dentistry is reinforced by increased esthetic demands of patients and dental professionals. © 2015 Wiley Periodicals, Inc.

Analysis on design and performance of a solar rotary house

NASA Astrophysics Data System (ADS)

Fan, Xuhong; Zhang, Zhaochang; Yang, Fan; Cao, Lilin; Xu, Jing; Yuan, Mingyang

2017-04-01

A solar rotary house is designed, composed of rotating main structure, fixed cylinder, rotating drive system, solar photovoltaic system and so on, to achieve 360° rotation. Thus it can change the dark and humid situation of the traditional fixed house shade. Its bearing capacity, driving force and safety are analyzed. Rotary driving force and living energy are provided by solar photovoltaic system on roofs and walls. The Phonenics, Ecotect simulation analysis conclude that the rotating house indoor has better natural ventilation effect, more uniform lighting, better the sunshine time compared with traditional houses, becoming a green, energy-saving, comfortable building model.

Lower-Dark-Current, Higher-Blue-Response CMOS Imagers

NASA Technical Reports Server (NTRS)

Pain, Bedabrata; Cunningham, Thomas; Hancock, Bruce

2008-01-01

Several improved designs for complementary metal oxide/semiconductor (CMOS) integrated-circuit image detectors have been developed, primarily to reduce dark currents (leakage currents) and secondarily to increase responses to blue light and increase signal-handling capacities, relative to those of prior CMOS imagers. The main conclusion that can be drawn from a study of the causes of dark currents in prior CMOS imagers is that dark currents could be reduced by relocating p/n junctions away from Si/SiO2 interfaces. In addition to reflecting this conclusion, the improved designs include several other features to counteract dark-current mechanisms and enhance performance.

Physiological asymmetry in etiolated pea epicotyls: relation to patterns of auxin distribution and phototropic behavior

NASA Technical Reports Server (NTRS)

Kuhn, H.; Galston, A. W.

1992-01-01

Etiolated pea seedlings require transformation of Pr phytochrome to Pfr before they display optimal phototropic response to unilateral blue light. This study investigates the possible role of auxin transport in explaining these phenomena. Labeled [2-14C]IAA applied to the intact terminal buds of dark-grown and red light-treated pea seedlings was measured 210 min later on the shaded and illuminated sides of the epicotyl as a function of direction and duration of irradiation with blue light. Totally darkened epicotyls show an asymmetry in distribution of radioactivity in the upper growth zone of the epicotyl, in favor of the side under the concave part of the apical hook. Red light, which greatly potentiates curvature toward subsequent unilateral blue light, lowers this asymmetry. Blue light directed to the epicotyl of red-pretreated plants in a plane parallel to the hook and from the side bearing the convex portion of the hook induces positive phototropic curvature as well as a surplus of radioactivity on the illuminated side of the upper epicotyl and on the shaded side of the lower growth zone of the epicotyl. Light directed to the side bearing the concave part of the hook also causes an accumulation of counts in the upper part of the lighted side but produces neither curvature of the epicotyl nor accumulation of counts in the lower shaded side. Because of this built-in physiological asymmetry in the growth zone just below the apical hook, it is difficult to explain the effects of red and blue light on curvature in terms of patterns of auxin distribution alone.

Impacts of sediments on coral energetics: partitioning the effects of turbidity and settling particles.

PubMed

Junjie, Reef K; Browne, Nicola K; Erftemeijer, Paul L A; Todd, Peter A

2014-01-01

Sediment loads have long been known to be deleterious to corals, but the effects of turbidity and settling particles have not previously been partitioned. This study provides a novel approach using inert silicon carbide powder to partition and quantify the mechanical effects of sediment settling versus reduced light under a chronically high sedimentary regime on two turbid water corals commonly found in Singapore (Galaxea fascicularis and Goniopora somaliensis). Coral fragments were evenly distributed among three treatments: an open control (30% ambient PAR), a shaded control (15% ambient PAR) and sediment treatment (15% ambient PAR; 26.4 mg cm(-2) day(-1)). The rate of photosynthesis and respiration, and the dark-adapted quantum yield were measured once a week for four weeks. By week four, the photosynthesis to respiration ratio (P/R ratio) and the photosynthetic yield (Fv/Fm) had fallen by 14% and 3-17% respectively in the shaded control, contrasting with corals exposed to sediments whose P/R ratio and yield had declined by 21% and 18-34% respectively. The differences in rates between the shaded control and the sediment treatment were attributed to the mechanical effects of sediment deposition. The physiological response to sediment stress differed between species with G. fascicularis experiencing a greater decline in the net photosynthetic yield (13%) than G. somaliensis (9.5%), but a smaller increase in the respiration rates (G. fascicularis = 9.9%, G. somaliensis  = 14.2%). These different physiological responses were attributed, in part, to coral morphology and highlighted key physiological processes that drive species distribution along high to low turbidity and depositional gradients.

Physiological asymmetry in etiolated pea epicotyls: relation to patterns of auxin distribution and phototropic behavior.

PubMed

Kuhn, H; Galston, A W

1992-01-01

Etiolated pea seedlings require transformation of Pr phytochrome to Pfr before they display optimal phototropic response to unilateral blue light. This study investigates the possible role of auxin transport in explaining these phenomena. Labeled [2-14C]IAA applied to the intact terminal buds of dark-grown and red light-treated pea seedlings was measured 210 min later on the shaded and illuminated sides of the epicotyl as a function of direction and duration of irradiation with blue light. Totally darkened epicotyls show an asymmetry in distribution of radioactivity in the upper growth zone of the epicotyl, in favor of the side under the concave part of the apical hook. Red light, which greatly potentiates curvature toward subsequent unilateral blue light, lowers this asymmetry. Blue light directed to the epicotyl of red-pretreated plants in a plane parallel to the hook and from the side bearing the convex portion of the hook induces positive phototropic curvature as well as a surplus of radioactivity on the illuminated side of the upper epicotyl and on the shaded side of the lower growth zone of the epicotyl. Light directed to the side bearing the concave part of the hook also causes an accumulation of counts in the upper part of the lighted side but produces neither curvature of the epicotyl nor accumulation of counts in the lower shaded side. Because of this built-in physiological asymmetry in the growth zone just below the apical hook, it is difficult to explain the effects of red and blue light on curvature in terms of patterns of auxin distribution alone.

Low-dark current 1024×1280 InGaAs PIN arrays

NASA Astrophysics Data System (ADS)

Yuan, Ping; Chang, James; Boisvert, Joseph C.; Karam, Nasser

2014-06-01

Photon counting imaging applications requires low noise from both detector and readout integrated circuit (ROIC) arrays. In order to retain the photon-counting-level sensitivity, a long integration time has to be employed and the dark current has to be minimized. It is well known that the PIN dark current is sensitive to temperature and a dark current density of 0.5 nA/cm2 was demonstrated at 7 °C previously. In order to restrain the size, weight, and power consumption (SWaP) of cameras for persistent large-area surveillance on small platforms, it is critical to develop large format PIN arrays with small pitch and low dark current density at higher operation temperatures. Recently Spectrolab has grown, fabricated and tested 1024x1280 InGaAs PIN arrays with 12.5 μm pitch and achieved 0.7 nA/cm2 dark current density at 15 °C. Based on our previous low-dark-current PIN designs, the improvements were focused on 1) the epitaxial material design and growth control; and 2) PIN device structure to minimize the perimeter leakage current and junction diffusion current. We will present characterization data and analyses that illustrate the contribution of various dark current mechanisms.

Masking properties of ceramics for veneer restorations.

PubMed

Skyllouriotis, Andreas L; Yamamoto, Hideo L; Nathanson, Dan

2017-10-01

The translucency and opacity of ceramics play a significant role in emulating the natural color of teeth, but studies of the masking properties and limitations of dental ceramics when used as monolayer restorations are lacking. The purpose of this in vitro study was to determine the translucency of 6 materials used for veneer restorations by assessing their translucency parameters (TPs), contrast ratios (CRs), and potential to mask dark tooth colors. Ten square- or disk-shaped specimens (0.5-mm thickness, shade A2) were fabricated from Vitablocks Mark II (VMII; Vita Zahnfabrik), IPS e.max CAD LT (EMXC LT; Ivoclar Vivadent AG), IPS e.max CAD HT (EMXC HT; Ivoclar Vivadent AG), IPS Empress CAD LT (EMP LT; Ivoclar Vivadent AG), IPS e.max Press LT (EMXP LT; Ivoclar Vivadent AG), and CZR (CZR; Kuraray Noritake Dental Inc). Their luminance (Y) values over black and over white tiles were measured, followed by their color (CIELab) over black tiles and white tiles and shaded A2 (control group), A3.5, A4, and B4 acrylic resin blocks. All measurements were performed using a spectrophotometer in 2 different areas on each specimen. Then CRs, TPs, and color differences (over shaded backgrounds) were determined. Data were subjected to 1-way and 2-way ANOVA (α=.05) for analysis. Mean CR values of EMXP LT were significantly higher than those of the other tested materials, whereas VMII and EMXC HT had the lowest values (P<.001). Mean TP values over black and over white backgrounds of VMII and EMXC HT were significantly higher than those of the other tested materials, while EMXP LT and EMXC LT revealed the lowest values (P<.001). Background shade A4 displayed the highest mean effect (expressed in ΔE* values) on the color of the ceramic materials, whereas shade B4 demonstrated the lowest mean background effect (P<.001). Significant differences in translucency among the tested ceramics were revealed (P<.001). The EMXC LT and EMXP LT groups were the least translucent under the conditions of this study (P<.001). All tested ceramics exhibited poor masking properties against the A4 background. The color differences of most tested ceramics were more acceptable when tested against the B4 background (ΔE*≤3.3). Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Leaf turnover and growth responses of shade-grown saplings of four Shorea rain forest species to a sudden increase in light.

PubMed

Shimizu, Michiru; Ishida, Atsushi; Tange, Takeshi; Yagi, Hisayoshi

2006-04-01

We tested the hypothesis that sapling growth following a sudden increase in solar irradiance is related to recovery from photoinhibition and the balance between rate of production of new leaves and rate of abscision of old leaves. Leaf gas exchange, chlorophyll fluorescence and relative growth rate (RGR) of stem basal area were measured following the sudden exposure of shade-grown (7% of full sunlight) saplings of four Shorea species to full sunlight. Sudden exposure to full sunlight resulted in an immediate and substantial reduction in dark-adapted quantum yield of photosystem II (Fv/Fm), followed by a gradual recovery in all species. Near light-saturated net assimilation rate (A max) and area-based leaf chlorophyll concentration ([Chl area]) also declined immediately after exposure. Eleven days after exposure, A max had recovered to pre-exposure values in all species, whereas [Chl area] had not recovered. Across species, RGR of stem basal area increased with increasing RGR of the number of leaves following exposure to full sunlight. The interspecific variations in RGR of stem basal area suggest that new leaf production is crucial for determining the potential growth of saplings following gap formation.

Melanins in Fossil Animals: Is It Possible to Infer Life History Traits from the Coloration of Extinct Species?

PubMed Central

Negro, Juan J.; Finlayson, Clive; Galván, Ismael

2018-01-01

Paleo-colour scientists have recently made the transition from describing melanin-based colouration in fossil specimens to inferring life-history traits of the species involved. Two such cases correspond to counter-shaded dinosaurs: dark-coloured due to melanins dorsally, and light-coloured ventrally. We believe that colour reconstruction of fossils based on the shape of preserved microstructures—the majority of paleo-colour studies involve melanin granules—is not without risks. In addition, animals with contrasting dorso-ventral colouration may be under different selection pressures beyond the need for camouflage, including, for instance, visual communication or ultraviolet (UV) protection. Melanin production is costly, and animals may invest less in areas of the integument where pigments are less needed. In addition, melanocytes exposed to UV radiation produce more melanin than unexposed melanocytes. Pigment economization may thus explain the colour pattern of some counter-shaded animals, including extinct species. Even in well-studied extant species, their diversity of hues and patterns is far from being understood; inferring colours and their functions in species only known from one or few specimens from the fossil record should be exerted with special prudence. PMID:29360744

Using microabrasive material to remove fluorosis stains.

PubMed

Allen, Kenneth; Agosta, Claudine; Estafan, Denise

2004-03-01

Increased public access to fluoride has decreased the prevalence of caries and increased the prevalence of fluorosis staining. This article provides a case report involving a conservative method of removing fluorosis stain, as well as describes an in vitro test of the method. A healthy man sought treatment at New York University College of Dentistry for removal of severe, dark brown fluorosis staining on his anterior teeth. To remove the stain, the treating clinician used a microabrasive material, which leaves enamel intact, instead of a tooth-whitening agent, which requires removal of all affected enamel. To demonstrate that enamel structure is not disturbed by the microabrasive material, the authors performed a study using scanning electron microscopy, or SEM. They viewed enamel structure under SEM at x1,000 magnification. They viewed untreated microabraded enamel and compared it with enamel that had been treated for 20 seconds with 37 percent phosphoric acid. An etch pattern was not discernible on the tooth treated with the microabrasive material. The enamel prisms remained intact and the cores were not exposed. Microabrasion removes intrinsic fluorosis stain effectively while protecting enamel. In this case, an enamel shade of brown not in the range of any tooth color shade guide was reduced.

The trehalose pathway in maize: conservation and gene regulation in response to the diurnal cycle and extended darkness.

PubMed

Henry, Clémence; Bledsoe, Samuel W; Siekman, Allison; Kollman, Alec; Waters, Brian M; Feil, Regina; Stitt, Mark; Lagrimini, L Mark

2014-11-01

Energy resources in plants are managed in continuously changing environments, such as changes occurring during the day/night cycle. Shading is an environmental disruption that decreases photosynthesis, compromises energy status, and impacts on crop productivity. The trehalose pathway plays a central but not well-defined role in maintaining energy balance. Here, we characterized the maize trehalose pathway genes and deciphered the impacts of the diurnal cycle and disruption of the day/night cycle on trehalose pathway gene expression and sugar metabolism. The maize genome encodes 14 trehalose-6-phosphate synthase (TPS) genes, 11 trehalose-6-phosphate phosphatase (TPP) genes, and one trehalase gene. Transcript abundance of most of these genes was impacted by the day/night cycle and extended dark stress, as were sucrose, hexose sugars, starch, and trehalose-6-phosphate (T6P) levels. After extended darkness, T6P levels inversely followed class II TPS and sucrose non-fermenting-related protein kinase 1 (SnRK1) target gene expression. Most significantly, T6P no longer tracked sucrose levels after extended darkness. These results showed: (i) conservation of the trehalose pathway in maize; (ii) that sucrose, hexose, starch, T6P, and TPS/TPP transcripts respond to the diurnal cycle; and(iii) that extended darkness disrupts the correlation between T6P and sucrose/hexose pools and affects SnRK1 target gene expression. A model for the role of the trehalose pathway in sensing of sucrose and energy status in maize seedlings is proposed. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Earth Observing-1 Advanced Imager Flight Performance Assessment: Investigating Dark Current Stability Over One-Half Orbit Period during the First 60 Days

NASA Technical Reports Server (NTRS)

Mendenhall, J. A.

2001-01-01

The stability of the EO-1 Advanced Land Imager dark current levels over the period of one-half orbit is investigated. A series of two-second dark current collections, over the course of 40 minutes, was performed during the first sixty days the instrument was in orbit. Analysis of this data indicates only two dark current reference periods, obtained entering and exiting eclipse, are required to remove ALI dark current offsets for 99.9% of the focal plane to within 1.5 digital numbers for any observation on the solar illuminated portion of the orbit.

Reliability and accuracy of four dental shade-matching devices.

PubMed

Kim-Pusateri, Seungyee; Brewer, Jane D; Davis, Elaine L; Wee, Alvin G

2009-03-01

There are several electronic shade-matching instruments available for clinical use, but the reliability and accuracy of these instruments have not been thoroughly investigated. The purpose of this in vitro study was to evaluate the reliability and accuracy of 4 dental shade-matching instruments in a standardized environment. Four shade-matching devices were tested: SpectroShade, ShadeVision, VITA Easyshade, and ShadeScan. Color measurements were made of 3 commercial shade guides (Vitapan Classical, Vitapan 3D-Master, and Chromascop). Shade tabs were placed in the middle of a gingival matrix (Shofu GUMY) with shade tabs of the same nominal shade from additional shade guides placed on both sides. Measurements were made of the central region of the shade tab positioned inside a black box. For the reliability assessment, each shade tab from each of the 3 shade guide types was measured 10 times. For the accuracy assessment, each shade tab from 10 guides of each of the 3 types evaluated was measured once. Differences in reliability and accuracy were evaluated using the Standard Normal z test (2 sided) (alpha=.05) with Bonferroni correction. Reliability of devices was as follows: ShadeVision, 99.0%; SpectroShade, 96.9%; VITA Easyshade, 96.4%; and ShadeScan, 87.4%. A significant difference in reliability was found between ShadeVision and ShadeScan (P=.008). All other comparisons showed similar reliability. Accuracy of devices was as follows: VITA Easyshade, 92.6%; ShadeVision, 84.8%; SpectroShade, 80.2%; and ShadeScan, 66.8%. Significant differences in accuracy were found between all device pairs (P<.001) for all comparisons except for SpectroShade versus ShadeVision (P=.033). Most devices had similar high reliability (over 96%), indicating predictable shade values from repeated measurements. However, there was more variability in accuracy among devices (67-93%), and differences in accuracy were seen with most device comparisons.

Effects of shade tab arrangement on the repeatability and accuracy of shade selection.

PubMed

Yılmaz, Burak; Yuzugullu, Bulem; Cınar, Duygu; Berksun, Semih

2011-06-01

Appropriate and repeatable shade matching using visual shade selection remains a challenge for the restorative dentist. The purpose of this study was to evaluate the effect of different arrangements of a shade guide on the repeatability and accuracy of visual shade selection by restorative dentists. Three Vitapan Classical shade guides were used for shade selection. Seven shade tabs from one shade guide were used as target shades for the testing (A1, A4, B2, B3, C2, C4, and D3); the other 2 guides were used for shade selection by the subjects. One shade guide was arranged according to hue and chroma and the second was arranged according to value. Thirteen male and 22 female restorative dentists were asked to match the target shades using shade guide tabs arranged in the 2 different orders. The sessions were performed twice with each guide in a viewing booth. Collected data were analyzed with Fisher's exact test to compare the accuracy and repeatability of the shade selection (α=.05). There were no significant differences observed in the accuracy or repeatability of the shade selection results obtained with the 2 different arrangements. When the hue/chroma-ordered shade guide was used, 58% of the shade selections were accurate. This ratio was 57.6% when the value-ordered shade guide was used. The observers repeated 55.5% of the selections accurately with the hue/chroma-ordered shade guide and 54.3% with the value-ordered shade guide. The accuracy and repeatability of shade selections by restorative dentists were similar when different arrangements (hue/chroma-ordered and value-ordered) of the Vitapan Classical shade guide were used. Copyright © 2011 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Simple and effective method to lock buoy position to ocean currents

NASA Technical Reports Server (NTRS)

Vachon, W. A.; Dahlen, J. M.

1975-01-01

Window-shade drogue, used with drifting buoys to keep them moving with current at speed as close to that of current as possible, has drag coefficient of 1.93 compared to maximum of 1.52 for previous drogues. It is remarkably simple to construct, use, and store.

First Monthly CERES Global Longwave and Shortwave Radiation

NASA Technical Reports Server (NTRS)

2002-01-01

Clouds and the Earth's Radiant Energy System, CERES, monitors solar energy reflected from the Earth and heat energy emitted from the Earth. In this image, heat energy radiated from the earth is shown in varying shades of yellow, red, blue and white. The brightest yellow areas, such as the Sahara Desert and Arabian Peninsula, are emitting the most energy out to space, while the dark blue polar regions and bright white clouds are the coldest areas on Earth, and are emitting the least energy. The animation (1.5MB) (high-res (4MB)) shows roughly a week of CERES data. For more information: CERES images through Visible Earth. CERES web site Image courtesy of the CERES instrument team

CERES Detects Earth's Heat and Energy

NASA Technical Reports Server (NTRS)

2002-01-01

Clouds and the Earth's Radiant Energy System, CERES, monitors solar energy reflected from the Earth and heat energy emitted from the Earth. In this image, heat energy radiated from the earth is shown in varying shades of yellow, red, blue and white. The brightest yellow areas, such as the Sahara Desert and Arabian Peninsula, are emitting the most energy out to space, while the dark blue polar regions and bright white clouds are the coldest areas on Earth, and are emitting the least energy. The animation (1.5MB) (high-res (4MB)) shows roughly a week of CERES data. For more information: CERES images through Visible Earth. CERES web site Image courtesy of the CERES instrument team

Development of Low Parasitic Light Sensitivity and Low Dark Current 2.8 μm Global Shutter Pixel †

PubMed Central

Yokoyama, Toshifumi; Tsutsui, Masafumi; Suzuki, Masakatsu; Nishi, Yoshiaki; Mizuno, Ikuo; Lahav, Assaf

2018-01-01

We developed a low parasitic light sensitivity (PLS) and low dark current 2.8 μm global shutter pixel. We propose a new inner lens design concept to realize both low PLS and high quantum efficiency (QE). 1/PLS is 7700 and QE is 62% at a wavelength of 530 nm. We also propose a new storage-gate based memory node for low dark current. P-type implants and negative gate biasing are introduced to suppress dark current at the surface of the memory node. This memory node structure shows the world smallest dark current of 9.5 e−/s at 60 °C. PMID:29370146

Development of Low Parasitic Light Sensitivity and Low Dark Current 2.8 μm Global Shutter Pixel.

PubMed

Yokoyama, Toshifumi; Tsutsui, Masafumi; Suzuki, Masakatsu; Nishi, Yoshiaki; Mizuno, Ikuo; Lahav, Assaf

2018-01-25

Abstract : We developed a low parasitic light sensitivity (PLS) and low dark current 2.8 μm global shutter pixel. We propose a new inner lens design concept to realize both low PLS and high quantum efficiency (QE). 1/PLS is 7700 and QE is 62% at a wavelength of 530 nm. We also propose a new storage-gate based memory node for low dark current. P-type implants and negative gate biasing are introduced to suppress dark current at the surface of the memory node. This memory node structure shows the world smallest dark current of 9.5 e - /s at 60 °C.

Effect of cross infection control barriers used on the light-curing device tips on the cure depth of a resin composite

PubMed Central

de Moraes Porto, Isabel Cristina Celerino; Ramos de Brito, Andréia Cristina; Parolia, Abhishek

2013-01-01

Background: Among the advice on prevent cross-infection was included usage of mechanical barriers on tips of photoactivation units. However, questions about the use of protective barriers placed on the light-curing unit's tips and the possibility of interference with the ability of guaranteeing an effective polymerization of composite resins need to be clarified. Aims: The aim of this study was to evaluate the effect of cross infection control barriers used on the light-curing device tips on the cure depth of composite resin. Materials and Methods: Power density measurements from the light-cure unit were recorded with a radiometer on ten separate occasions with different types and placement modes of each barrier (low-density polyethylene and polyvinyl chloride (PVC) film – smooth and folds) and no-barrier (control). Cure depth of TPH™ Spectrum™ resin, A2-A4, was evaluated by the scraping test. Statistical Analysis: The data were analyzed using Student's t-test or ANOVA one-way with Tukey's test (α =0.05). Results: Same type of barrier and different shades (A2, A4) of composite exhibited significant difference in the cure depth among all groups (P < 0.05). Both low-density polyethylene and PVC film folded barriers produced a significant reduction in the light intensity (P < 0.05). Conclusions: Regarding the resin shade, there was a significant reduction in the cure depth of A4 composite resin (dark shade) but this reduction is not enough to cause any adverse effect on the material's clinical performance. Therefore, disposable barriers can be recommended for use over the end of the light guide. PMID:23833455

Leaf variations in Elaeagnus angustifolia related to environmental heterogeneity.

PubMed

Klich

2000-11-01

Elaeagnus angustifolia (Russian olive) is a Eurasian tree that has become naturalized and has invaded zones along watercourses in many arid and semiarid regions of the world. These habitats are characterized by vertical environmental gradients, thus trees must develop some plasticity to adapt to the wide range of site conditions. This study was undertaken to test the hypothesis that variations in leaf anatomy and morphology of E. angustifolia reflect their adaptability to the differences in the microclimate that occur within the canopy of single trees. Foliar architecture, blade and petiole epidermal and internal anatomy were examined in leaves at different canopy positions and related to environmental conditions. Upper sun-leaves are exposed to higher solar irradiance and lower air humidity and are smaller, more slender and thicker than the lower, half-exposed and shade-leaves. Color varies between the leaves at different levels, from silvery grey-green in the upper strata, to dark green in the lower one. Bicolor is more evident in half-exposed and shaded leaves. When compared with the lower half-exposed and shade-leaves, the upper leaves of E. angustifolia have a greater areole density, a higher mesophyll proportion and stomatal density. Trichomes are multicellular, pedestalled, stellate-branched or peltate and their form and density can be associated with leaf color and appearance. The slender petioles of the upper leaves have proportionally more epidermis, collenchyma and phloem and less parenchyma and xylem than those of lower leaves, when observed in transverse sections. Foliar morphological and anatomical variability in E. angustifolia may be considered an adaptive advantage that enables leaves to develop and function in habitats marked by strong variations of solar radiation, air temperature and humidity.

Influence of abutment material and luting cements color on the final color of all ceramics.

PubMed

Dede, Dogu Ömür; Armaganci, Arzu; Ceylan, Gözlem; Cankaya, Soner; Celik, Ersan

2013-11-01

The purpose of this study is to evaluate the effects of different abutment materials and luting cements color on the final color of implant-supported all-ceramic restorations. Ten A2 shade IPS e.max Press disc shape all-ceramic specimens were prepared (11 × 1.5 mm). Three different shades (translucent, universal and white opaque) of disc shape luting cement specimens were prepared (11 × 0.2 mm). Three different (zirconium, gold-palladium and titanium) implant abutments and one composite resin disc shape background specimen were prepared at 11 mm diameter and appropriate thicknesses. All ceramic specimens colors were measured with each background and luting cement samples on a teflon mold. A digital spectrophotometer used for measurements and data recorded as CIE L*a*b* color co-ordinates. An optical fluid applied on to the samples to provide a good optical connection and measurements on the composite resin background was saved as the control group. ΔE values were calculated from the ΔL, Δa and Δb values between control and test groups and data were analyzed with one-way variance analysis (ANOVA) and mean values were compared by the Tukey HSD test (α = 0.05). One-way ANOVA of ΔL, Δa, Δb and ΔE values of control and test groups revealed significant differences for backgrounds and seldom for cement color groups (p the 0.05). Only zirconium implant abutment groups and gold palladium abutment with universal shade cement group were found to be clinically acceptable (ΔE ≤ 3.0). Using titanium or gold-palladium abutments for implant supported all ceramics will be esthetically questionable and white opaque cement will be helpful to mask the dark color of titanium abutment.

Impacts of Sediments on Coral Energetics: Partitioning the Effects of Turbidity and Settling Particles

PubMed Central

Junjie, Reef K.; Browne, Nicola K.; Erftemeijer, Paul L. A.; Todd, Peter A.

2014-01-01

Sediment loads have long been known to be deleterious to corals, but the effects of turbidity and settling particles have not previously been partitioned. This study provides a novel approach using inert silicon carbide powder to partition and quantify the mechanical effects of sediment settling versus reduced light under a chronically high sedimentary regime on two turbid water corals commonly found in Singapore (Galaxea fascicularis and Goniopora somaliensis). Coral fragments were evenly distributed among three treatments: an open control (30% ambient PAR), a shaded control (15% ambient PAR) and sediment treatment (15% ambient PAR; 26.4 mg cm−2 day−1). The rate of photosynthesis and respiration, and the dark-adapted quantum yield were measured once a week for four weeks. By week four, the photosynthesis to respiration ratio (P/R ratio) and the photosynthetic yield (Fv/Fm) had fallen by 14% and 3–17% respectively in the shaded control, contrasting with corals exposed to sediments whose P/R ratio and yield had declined by 21% and 18–34% respectively. The differences in rates between the shaded control and the sediment treatment were attributed to the mechanical effects of sediment deposition. The physiological response to sediment stress differed between species with G. fascicularis experiencing a greater decline in the net photosynthetic yield (13%) than G. somaliensis (9.5%), but a smaller increase in the respiration rates (G. fascicularis = 9.9%, G. somaliensis = 14.2%). These different physiological responses were attributed, in part, to coral morphology and highlighted key physiological processes that drive species distribution along high to low turbidity and depositional gradients. PMID:25197883

American Samoa, Shaded Relief and Colored Height

NASA Image and Video Library

2009-10-01

The topography of Tutuila, largest of the islands of American Samoa, is well shown in this color-coded perspective view generated with digital elevation data from the Shuttle Radar Topography Mission (SRTM.) The total area of Tutuila is about 141.8 square kilometers (54.8 square miles), slightly larger than San Francisco. The large bay near the center in this view is Pago Pago Harbor, actually a submerged volcanic crater whose south wall collapsed millions of years ago. Adjacent to the harbor is Pago Pago, the capital of American Samoa, and to the left (west) of the harbor in this view is Matafao Peak, Tutuila’s highest point at 653 meters (2,142 feet). On September 29, 2009, a tsunami generated by a major undersea earthquake located about 200 kilometers (120 miles) southwest of Tutuila inundated the more heavily populated southern coast of the island with an ocean surge more than 3 meters (10 feet) deep, causing scores of casualties. Digital topographic data such as those produced by SRTM aid researchers and planners in predicting which coastal regions are at the most risk from such waves, as well as from the more common storm surges caused by tropical storms and even sea level rise. Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shaded image was derived by computing topographic slope in the northeast-southwest direction, so that northeast slopes appear bright and southwest slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. The image was then projected using the elevation data to produce this perspective view, with the topography exaggerated by a factor of two. http://photojournal.jpl.nasa.gov/catalog/PIA11965

Faster photosynthetic induction in tobacco by expressing cyanobacterial flavodiiron proteins in chloroplasts.

PubMed

Gómez, Rodrigo; Carrillo, Néstor; Morelli, María P; Tula, Suresh; Shahinnia, Fahimeh; Hajirezaei, Mohammad-Reza; Lodeyro, Anabella F

2018-05-01

Plants grown in the field experience sharp changes in irradiation due to shading effects caused by clouds, other leaves, etc. The excess of absorbed light energy is dissipated by a number of mechanisms including cyclic electron transport, photorespiration, and Mehler-type reactions. This protection is essential for survival but decreases photosynthetic efficiency. All phototrophs except angiosperms harbor flavodiiron proteins (Flvs) which relieve the excess of excitation energy on the photosynthetic electron transport chain by reducing oxygen directly to water. Introduction of cyanobacterial Flv1/Flv3 in tobacco chloroplasts resulted in transgenic plants that showed similar photosynthetic performance under steady-state illumination, but displayed faster recovery of various photosynthetic parameters, including electron transport and non-photochemical quenching during dark-light transitions. They also kept the electron transport chain in a more oxidized state and enhanced the proton motive force of dark-adapted leaves. The results indicate that, by acting as electron sinks during light transitions, Flvs contribute to increase photosynthesis protection and efficiency under changing environmental conditions as those found by plants in the field.

Effects of shade on physiological changes, oxidative stress, and total antioxidant power in Thai Brahman cattle.

PubMed

Aengwanich, Worapol; Kongbuntad, Watee; Boonsorn, Thongchai

2011-09-01

The purpose of this study was to assess the effects of artificial shade, tree shade, and no shade on physiological changes, oxidative stress, and total antioxidant power in Thai Brahman cattle. Twenty-one cattle were divided into three groups: cattle maintained under artificial shade, under tree shade, and without shade. On days 1, 7, 14, 21, and 28 of the experimental period, after the cattle were set in individual stalls for 2 h, physiological changes, thiobarbituric acid reactive substances (TBARS), and total antioxidant power were investigated. The results revealed that the respiratory rate, heart rate, sweat rate and the neutrophil/lymphocyte ratio of the no-shade cattle were significantly higher than those of cattle maintained under artificial shade and tree shade (P < 0.05). During the early period of heat exposure, the total antioxidant power of the no-shade cattle was lower than those of cattle maintained under artificial shade and tree shade, but the total antioxidant power of cattle maintained under artificial shade and tree shade were not different (P > 0.05). However, rectal temperature and packed cell volume of the cattle in all groups did not differ (P > 0.05). These results showed that artificial shade and tree shade can protect cattle from sunlight compared to no shade, and that the effectiveness of tree shade for sunlight protection is at an intermediate level.

40 shades of black: regional differences in vegetation response to a changing human influence in the Low Countries during the Dark Ages (AD 300-1000).

NASA Astrophysics Data System (ADS)

Gouw-Bouman, Marjolein T. I. J.; Donders, Timme H.; Hoek, Wim Z.

2016-04-01

During the Dark Ages, which includes the Late Roman Period (LRP, AD 300-500) and the Early Middle Ages (EMA, AD 500-1000), large scale vegetation development in Northwestern Europe is generally characterized by a forest regeneration. This forest redevelopment phase was not uniformous across the Netherlands. A comparison between existing pollen records shows that forest redevelopment started earlier and was more severe in the southern part of the Netherlands than in the northeastern Netherlands. The prevailing view advocates that the forest redevelopment is the result of a diminishing human influence on the landscape due to the collapse of the Roman Empire. Following this view, regional changes in forest regeneration are explained by varying population densities. However, existing climate-records indicate a colder and wetter climate during the Dark Ages and the geomorphological record points to a changing landscape. How and to what extent these climatic and environmental changes contributed to the changes in vegetation development or even to the decline of the Roman Empire is largely unknown. To understand the relative importance of the factors (climate, environment, economy and demography) influencing vegetation development it is important to accurately map regional differences in vegetation both on a regional and extra-regional scale. For an extra-regional overview all available pollen records in the Netherlands from this period are compiled to show differences in amplitude of the vegetation development during the Dark Ages. On a regional scale, vegetation reconstruction maps have been produced reflecting the influence of geological/geomorphological factors.

Mt. Elgon, Africa, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

The striking contrast of geologic structures in Africa is shown in this shaded relief image of Mt. Elgon on the left and a section of the Great Rift Valley on the right.

Mt. Elgon is a solitary extinct volcano straddling the border between Uganda and Kenya, and at 4,321 meters (14,178 feet) tall is the eighth highest mountain in Africa. It is positioned on the Pre-Cambriam bedrock of the Trans Nzoia Plateau, and is similar to other such volcanoes in East Africa in that it is associated with the formation of the Rift Valley. However one thing that sets Mt. Elgon apart is its age.

Although there is no verifiable evidence of its earliest volcanic activity, Mt. Elgon is estimated to be at least 24 million years old, making it the oldest extinct volcano in East Africa. This presents a striking comparison to Mt. Kilimanjaro, the highest mountain in Africa at 5,895 meters (19,341 feet), which is just over one million years old. Judging by the diameter of its base, it is a common belief among geological experts that Mt. Elgon was once the highest mountains in Africa, however erosion has played a significant role in reducing the height to its present value.

Juxtaposed with this impressive mountain is a section of the Great Rift Valley, a geological fault system that extends for about 4,830 kilometers (2,995 miles) from Syria to central Mozambique. Erosion has concealed some sections, but in some sections like that shown here, there are sheer cliffs several thousand feet high. The present configuration of the valley, which dates from the mid-Pleistocene epoch, results from a rifting process associated with thermal currents in the Earth's mantle.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Location: 1 degree north latitude, 35 degrees east longitude Orientation: North toward the top, Mercator projection Size: 223 by 223 kilometers (138 by 138 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Simulating glories and cloudbows in color.

PubMed

Gedzelman, Stanley D

2003-01-20

Glories and cloudbows are simulated in color by use of the Mie scattering theory of light upwelling from small-droplet clouds of finite optical thickness embedded in a Rayleigh scattering atmosphere. Glories are generally more distinct for clouds of droplets of as much as approximately 10 microm in radius. As droplet radius increases, the glory shrinks and becomes less prominent, whereas the cloudbow becomes more distinct and eventually colorful. Cloudbows typically consist of a broad, almost white band with a slightly orange outer edge and a dark inner band. Multiple light and dark bands that are related to supernumerary rainbows first appear inside the cloudbow as droplet radius increases above approximately 10 microm and gradually become more prominent when all droplets are the same size. Bright glories with multiple rings and high color purity are simulated when all droplets are the same size and every light beam is scattered just once. Color purity decreases and outer rings fade as the range of droplet sizes widens and when skylight, reflected light from the ground or background, and multiply scattered light from the cloud are included. Consequently, the brightest and most colorful glories and bows are seen when the observer is near a cloud or a rain swath with optical thickness of approximately 0.25 that consists of uniform-sized drops and when a dark or shaded background lies a short distance behind the cloud.

Twenty-Two Years of Warming, Fertilisation and Shading of Subarctic Heath Shrubs Promote Secondary Growth and Plasticity but Not Primary Growth

PubMed Central

Campioli, Matteo; Leblans, Niki; Michelsen, Anders

2012-01-01

Most manipulation experiments simulating global change in tundra were short-term or did not measure plant growth directly. Here, we assessed the growth of three shrubs (Cassiope tetragona, Empetrum hermaphroditum and Betula nana) at a subarctic heath in Abisko (Northern Sweden) after 22 years of warming (passive greenhouses), fertilisation (nutrients addition) and shading (hessian fabric), and compare this to observations from the first decade of treatment. We assessed the growth rate of current-year leaves and apical stem (primary growth) and cambial growth (secondary growth), and integrated growth rates with morphological measurements and species coverage. Primary- and total growth of Cassiope and Empetrum were unaffected by manipulations, whereas growth was substantially reduced under fertilisation and shading (but not warming) for Betula. Overall, shrub height and length tended to increase under fertilisation and warming, whereas branching increased mostly in shaded Cassiope. Morphological changes were coupled to increased secondary growth under fertilisation. The species coverage showed a remarkable increase in graminoids in fertilised plots. Shrub response to fertilisation was positive in the short-term but changed over time, likely because of an increased competition with graminoids. More erected postures and large, canopies (requiring enhanced secondary growth for stem reinforcement) likely compensated for the increased light competition in Empetrum and Cassiope but did not avoid growth reduction in the shade intolerant Betula. The impact of warming and shading on shrub growth was more conservative. The lack of growth enhancement under warming suggests the absence of long-term acclimation for processes limiting biomass production. The lack of negative effects of shading on Cassiope was linked to morphological changes increasing the photosynthetic surface. Overall, tundra shrubs showed developmental plasticity over the longer term. However, such plasticity was associated clearly with growth rate trends only in fertilised plots. PMID:22511968

Dark current of organic heterostructure devices with insulating spacer layers

NASA Astrophysics Data System (ADS)

Yin, Sun; Nie, Wanyi; Mohite, Aditya D.; Saxena, Avadh; Smith, Darryl L.; Ruden, P. Paul

2015-03-01

The dark current density at fixed voltage bias in donor/acceptor organic planar heterostructure devices can either increase or decrease when an insulating spacer layer is added between the donor and acceptor layers. The dominant current flow process in these systems involves the formation and subsequent recombination of an interfacial exciplex state. If the exciplex formation rate limits current flow, the insulating interface layer can increase dark current whereas, if the exciplex recombination rate limits current flow, the insulating interface layer decreases dark current. We present a device model to describe this behavior and illustrate it experimentally for various donor/acceptor systems, e.g. P3HT/LiF/C60.

SRTM Colored Height and Shaded Relief: Corral de Piedra, Argentina

NASA Technical Reports Server (NTRS)

2001-01-01

Volcanism and erosion are prominently seen in this view of the eastern flank of the Andes Mountains taken by Shuttle Radar Topography Mission (SRTM). The area is southeast of San Martin de Los Andes, Argentina. Eroded peaks up to 2,210-meter-high (7,260-foot) are seen on the west (left), but much of the scene consists of lava plateaus that slope gently eastward. These lava flows were most likely derived from volcanic sources in the high mountains. However, younger and more localized volcanic activity is evident in the topographic data as a cone surrounding oval-shaped flow near the center of the scene.

The plateaus are extensively eroded by the Rio Limay (bottom of the image) and the Rio Collon Cura and its tributaries (upper half). The larger stream channels have reached a stable level and are now cutting broad valleys. Few terraces between the levels of the high plateaus and lower valleys (bottom center and upper right of the volcanic cone) indicate that stream erosion had once temporarily reached a higher stable level before eroding down to its current level. In general, depositional surfaces like lava flows are progressively younger with increasing elevation, while erosional surfaces are progressively younger with decreasing elevation.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark, as would be the case at noon at this latitude in the southern hemisphere. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red and magenta to white at the highest elevations.

Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on February 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Size: 57.6 x 40.5 kilometers ( 35.7 x 25.1 miles) Location: 40.4 deg. South lat., 70.8 deg. West lon. Orientation: North toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

Dark Currents and Their Effect on the Primary Beam in an X-band Linac

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bane, K.L.F.; Dolgashev, V.A.; Raubenheimer, T.

2005-05-27

We numerically study properties of primary dark currents in an X-band accelerating structure. For the H60VG3 structure considered for the Next Linear Collider (NLC) we first perform a fairly complete (with some approximations) calculation of dark current trajectories. These results are used to study properties of the dark current leaving the structure. For example, at accelerating gradient of 65 MV/m, considering two very different assumptions about dark current emission around the irises, we find that the fraction of emitted current leaving the structure to be a consistent {approx} 1%. Considering that {approx} 1 mA outgoing dark current is seen inmore » measurement, this implies that {approx} 100 mA (or 10 pC per period) is emitted within the structure itself. Using the formalism of the Lienard-Wiechert potentials, we then perform a systematic calculation of the transverse kick of dark currents on a primary linac bunch. The result is {approx} 1 V kick per mA (or per 0.1 pC per period) dark current emitted from an iris. For an entire structure we estimate the total kick on a primary bunch to be {approx} 15 V. For the NLC linac this translates to a ratio of (final) vertical beam offset to beam size of about 0.2. However, with the assumptions that needed to be made--particularly the number of emitters and their distribution within a structure--the accuracy of this result may be limited to the order of magnitude.« less

In vitro model to evaluate reliability and accuracy of a dental shade-matching instrument.

PubMed

Kim-Pusateri, Seungyee; Brewer, Jane D; Dunford, Robert G; Wee, Alvin G

2007-11-01

There are several electronic shade-matching instruments available for clinical use; unfortunately, there are limited acceptable in vitro models to evaluate their reliability and accuracy. The purpose of this in vitro study was to evaluate the reliability and accuracy of a dental clinical shade-matching instrument. Using the shade-matching instrument (ShadeScan), color measurements were made of 3 commercial shade guides (VITA Classical, VITA 3D-Master, and Chromascop). Shade tabs were selected and placed in the middle of a gingival matrix (Shofu Gummy), with tabs of the same nominal shade from additional shade guides placed on both sides. Measurements were made of the central region of the shade tab inside a black box. For the reliability assessment, each shade tab from each of the 3 shade guide types was measured 10 times. For the accuracy assessment, each shade tab from 10 guides of each of the 3 types evaluated was measured once. Reliability, accuracy, and 95% confidence intervals were calculated for each shade tab. Differences were determined by 1-way ANOVA followed by the Bonferroni multiple comparison procedure. Reliability of ShadeScan was as follows: VITA Classical = 95.0%, VITA 3D-Master = 91.2%, and Chromascop = 76.5%. Accuracy of ShadeScan was as follows: VITA Classical = 65.0%, VITA 3D-Master = 54.2%, Chromascop = 84.5%. This in vitro study showed a varying degree of reliability and accuracy for ShadeScan, depending on the type of shade guide system used.

Controls on declining carbon balance with leaf age among 10 woody species in Australian woodland: do leaves have zero daily net carbon balances when they die?

PubMed

Reich, Peter B; Falster, Daniel S; Ellsworth, David S; Wright, Ian J; Westoby, Mark; Oleksyn, Jacek; Lee, Tali D

2009-01-01

* Here, we evaluated how increased shading and declining net photosynthetic capacity regulate the decline in net carbon balance with increasing leaf age for 10 Australian woodland species. We also asked whether leaves at the age of their mean life-span have carbon balances that are positive, zero or negative. * The net carbon balances of 2307 leaves on 53 branches of the 10 species were estimated. We assessed three-dimensional architecture, canopy openness, photosynthetic light response functions and dark respiration rate across leaf age sequences on all branches. We used YPLANT to estimate light interception and to model carbon balance along the leaf age sequences. * As leaf age increased to the mean life-span, increasing shading and declining photosynthetic capacity each separately reduced daytime carbon gain by approximately 39% on average across species. Together, they reduced daytime carbon gain by 64% on average across species. * At the age of their mean life-span, almost all leaves had positive daytime carbon balances. These per leaf carbon surpluses were of a similar magnitude to the estimated whole-plant respiratory costs per leaf. Thus, the results suggest that a whole-plant economic framework, including respiratory costs, may be useful in assessing controls on leaf longevity.

Autofluorescence study and selected cyanidin quantification in the Jewel orchids Anoectochilus sp. and Ludisia discolor.

PubMed

Poobathy, Ranjetta; Zakaria, Rahmad; Murugaiyah, Vikneswaran; Subramaniam, Sreeramanan

2018-01-01

Anoectochilus sp. and Ludisia discolor are known as Jewel orchids. Both species are terrestrial wild orchids that grow in shaded areas of forests. The Jewel orchids are renowned for the beauty of their leaves, which are dark-green laced with silvery or golden veins. The orchids are used as a cure in various parts of Asia. Overharvesting and anthropogenic disturbances threaten the existence of the Jewel orchids in the wild, necessitating human intervention in their survival. An understanding of the structure and adaptations of a plant may assist in its survival when propagated outside of its habitat. In this study, ex vitro leaves of Anoectochilus sp. and L. discolor were subjected to freehand sectioning, and then inspected through brightfield and fluorescence microscopy. The study indicated that all parts of both plants presented typical monocotyledonous characteristics except the leaves. The leaves displayed dorsiventrality with distinct palisade and spongy mesophyll layers. The spongy mesophyll layer contained cells which fluoresced a bright red when exposed to ultraviolet, blue, and green light wavelengths, hinting at the presence of anthocyanins for photoprotection. Cyanidin was detected in the leaves of L. discolor, as enumerated through high performance liquid chromatography (HPLC). The observations indicated that Anoectochilus sp. and L. discolor are well-adapted to live under shaded conditions with minimal exposure to light.

The handedness of Leonardo da Vinci: a tale of the complexities of lateralisation.

PubMed

McManus, I C; Drury, Helena

2004-07-01

The handedness of Leonardo da Vinci is controversial. Although there is little doubt that many of his well-attributed drawings were drawn with the left hand, the hatch marks of the shading going downwards from left to right, it is not clear that he was a natural left-hander, there being some suggestion that he may have become left-handed as the result of an injury to his right hand in early adulthood. Leonardo's lateralisation may be illuminated by an obscure passage in his notebooks in which he describes crouching down to look into a dark cave, putting his left hand on his knee, and shading his eyes with his right hand. We carried out a questionnaire survey, using 33 written and photographic items, to find whether this behaviour was typical of right handers or left handers. In fact the 'Leonardo task' showed almost no direct association with handedness, meaning that it contributes little to the immediate problem of elucidating Leonardo's handedness. However, the lateralisation of the task did relate to other aspects of behavioural laterality in surprisingly complex ways. This suggests that individual differences in handedness, and behavioural laterality in general, have a structural complexity which is not fully encompassed by simple measures of direction or degree of handedness.

Light-mediated polarization of the PIN3 auxin transporter for the phototropic response in Arabidopsis.

PubMed

Ding, Zhaojun; Galván-Ampudia, Carlos S; Demarsy, Emilie; Łangowski, Łukasz; Kleine-Vehn, Jürgen; Fan, Yuanwei; Morita, Miyo T; Tasaka, Masao; Fankhauser, Christian; Offringa, Remko; Friml, Jiří

2011-04-01

Phototropism is an adaptation response, through which plants grow towards the light. It involves light perception and asymmetric distribution of the plant hormone auxin. Here we identify a crucial part of the mechanism for phototropism, revealing how light perception initiates auxin redistribution that leads to directional growth. We show that light polarizes the cellular localization of the auxin efflux carrier PIN3 in hypocotyl endodermis cells, resulting in changes in auxin distribution and differential growth. In the dark, high expression and activity of the PINOID (PID) kinase correlates with apolar targeting of PIN3 to all cell sides. Following illumination, light represses PINOID transcription and PIN3 is polarized specifically to the inner cell sides by GNOM ARF GTPase GEF (guanine nucleotide exchange factor)-dependent trafficking. Thus, differential trafficking at the shaded and illuminated hypocotyl side aligns PIN3 polarity with the light direction, and presumably redirects auxin flow towards the shaded side, where auxin promotes growth, causing hypocotyls to bend towards the light. Our results imply that PID phosphorylation-dependent recruitment of PIN proteins into distinct trafficking pathways is a mechanism to polarize auxin fluxes in response to different environmental and endogenous cues. © 2011 Macmillan Publishers Limited. All rights reserved

Bali, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

The volcanic nature of the island of Bali is evident in this shaded relief image generated with data from the Shuttle Radar Topography Mission (SRTM).

Bali, along with several smaller islands, make up one of the 27 Provinces of Indonesia. It lies over a major subduction zone where the Indo-Australian tectonic plate collides with the Sunda plate, creating one of the most volcanically active regions on the planet.

The most significant feature on Bali is Gunung Agung, the symmetric, conical mountain at the right-center of the image. This 'stratovolcano,' 3,148 meters (10,308 feet) high, is held sacred in Balinese culture, and last erupted in 1963 after being dormant and thought inactive for 120 years. This violent event resulted in over 1,000 deaths, and coincided with a purification ceremony called Eka Dasa Rudra, meant to restore the balance between nature and man. This most important Balinese rite is held only once per century, and the almost exact correspondence between the beginning of the ceremony and the eruption is though to have great religious significance.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Location: 8.33 degrees South latitude, 115.17 degrees East longitude Orientation: North toward the top, Mercator projection Size: 153 by 112 kilometers (95 by 69 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Sinai Peninsula, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

The Sinai Peninsula, located between Africa and Asia, is a result of those two continents pulling apart from each other. Earth's crust is cracking, stretching, and lowering along the two northern branches of the Red Sea, namely the Gulf of Suez, seen here on the west (left), and the Gulf of Aqaba, seen to the east (right). This color-coded shaded relief image shows the triangular nature of the peninsula, with the coast of the Mediterranean Sea forming the northern side of the triangle. The Suez Canal can be seen as the narrow vertical blue line in the upper left connecting the Red Sea to the Mediterranean.

The peninsula is divided into three distinct parts; the northern region consisting chiefly of sandstone, plains and hills, the central area dominated by the Tih Plateau, and the mountainous southern region where towering peaks abound. Much of the Sinai is deeply dissected by river valleys, or wadis, that eroded during an earlier geologic period and break the surface of the plateau into a series of detached massifs with a few scattered oases.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise,Washington, D.C.

Location: 30 degrees north latitude, 34 degrees east longitude Orientation: North toward the top, Mercator projection Size: 289 by 445 kilometers (180 by 277 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Earth Observing-1 Advanced Land Imager: Dark Current and Noise Characterization and Anomalous Detectors

NASA Technical Reports Server (NTRS)

Mendenhall, J. A.

2001-01-01

The dark current and noise characteristics of the Earth Observing-1 Advanced Land Imager measured during ground calibration at MIT Lincoln Laboratory are presented. Data were collected for the nominal focal plane operating temperature of 220 K as well as supplemental operating temperatures (215 and 225 K). Dark current baseline values are provided, and noise characterization includes the evaluation of white, coherent, low frequency, and high frequency components. Finally, anomalous detectors, characterized by unusual dark current, noise, gain, or cross-talk properties are investigated.

Relationships between ambient conditions, thermal status, and feed intake of cattle during summer heat stress with access to shade.

PubMed

Curtis, A K; Scharf, B; Eichen, P A; Spiers, D E

2017-01-01

Heat stress in feedlot cattle is known to reduce their performance. The challenge comes in determining reliable predictors of current and near-future changes in thermal status and performance. A 42-d study, using crossbred (Bos taurus) steers was conducted during summer months (July through August) to identify best environmental determinants of rumen temperature (T rumen ) and feed intake (FI) in feedlot cattle with access to shade. A further goal was to define the relationship between T rumen and FI. Shade coverage was approximately 50%, and all animals were provided standard feedlot diets and water ad libitum. Intraruminal telemetric boluses recorded T rumen several times each hour. Ear tags, telemetrically connected to a feed monitoring system, provided FI data using RFID technology. Data loggers recorded ambient conditions in sun and shade, along with black globe temperature. Regression analyses identified daylight black globe and air temperatures in shade, with one hour delays, as the best predictors of T rumen . Prediction of FI was much less reliable. Unexpectedly, T rumen was not superior to ambient variables in predicting FI. Maximum daily temperature humidity index, calculated using BG in sun with a 5-d lag, was the best significant predictor of FI. These results indicate for feedlot cattle that although air temperature alone in the shade may be the best predictor of T rumen in the heat, black globe temperature in the sun may be a better determinant of feed intake over time. Additional studies are needed to verify the delayed FI response which seems unusually long. Copyright © 2016 Elsevier Ltd. All rights reserved.

Accounting for Dark Current Accumulated during Readout of Hubble's ACS/WFC Detectors

NASA Astrophysics Data System (ADS)

Ryon, Jenna E.; Grogin, Norman A.; Coe, Dan A.; ACS Team

2018-06-01

We investigate the properties of excess dark current accumulated during the 100-second full-frame readout of the Advanced Camera for Surveys (ACS) Wide Field Channel (WFC) detectors. This excess dark current, called "readout dark", gives rise to ambient background gradients and hot columns in each ACS/WFC image. While readout dark signal is removed from science images during the bias correction step in CALACS, the additional noise from the readout dark is currently not taken into account. We develop a method to estimate the readout dark noise properties in ACS/WFC observations. We update the error (ERR) extensions of superbias images to include the appropriate noise from the ambient readout dark gradient and stable hot columns. In recent data, this amounts to about 5 e-/pixel added variance in the rows farthest from the WFC serial registers, and about 7 to 30 e-/pixel added variance along the stable hot columns. We also flag unstable hot columns in the superbias data quality (DQ) extensions. The new reference file pipeline for ACS/WFC implements these updates to our superbias creation process.

An Exploration of WFC3/IR Dark Current Variation

NASA Astrophysics Data System (ADS)

Sunnquist, B.; Baggett, S.; Long, K. S.

2017-02-01

We use a collection of darks spanning September 2009 to June 2016 to study variations in the dark current in the IR detector on WFC3. Although the darks possess a similar signal pattern across the detector, we find that their median dark rates vary by as much as 0.014 DN/s (0.032 e-/s). The distribution of these median values has a triangular shape with a mean and standard deviation of 0.021 ± 0.0029 DN/s (0.049 ± 0.0069 e-/s). We observe a long term time-dependence in the inboard vertical reference pixel and zeroth read signals; however, these differences do not noticeably affect the calibrated dark signals, and we conclude that the WFC3/IR dark current levels continue to remain stable since launch. The inboard reference pixel signals exhibit a unique, but consistent, pattern around the detector, but this pattern does not evolve noticeably with the median of the science pixels, and a quadrant or row-based reference pixel subtraction strategy does not reduce the spread between the median dark rates. We notice a slight drift in the inboard reference pixel signals up the dark ramps, and the intensity of this drift is related to the median dark current in the science pixels. This holds true using either the horizontal or vertical reference pixels and for darks with a variety of sample sequences.

Tradeoffs between income, biodiversity, and ecosystem functioning during tropical rainforest conversion and agroforestry intensification

PubMed Central

Steffan-Dewenter, Ingolf; Kessler, Michael; Barkmann, Jan; Bos, Merijn M.; Buchori, Damayanti; Erasmi, Stefan; Faust, Heiko; Gerold, Gerhard; Glenk, Klaus; Gradstein, S. Robbert; Guhardja, Edi; Harteveld, Marieke; Hertel, Dietrich; Höhn, Patrick; Kappas, Martin; Köhler, Stefan; Leuschner, Christoph; Maertens, Miet; Marggraf, Rainer; Migge-Kleian, Sonja; Mogea, Johanis; Pitopang, Ramadhaniel; Schaefer, Matthias; Schwarze, Stefan; Sporn, Simone G.; Steingrebe, Andrea; Tjitrosoedirdjo, Sri S.; Tjitrosoemito, Soekisman; Twele, André; Weber, Robert; Woltmann, Lars; Zeller, Manfred; Tscharntke, Teja

2007-01-01

Losses of biodiversity and ecosystem functioning due to rainforest destruction and agricultural intensification are prime concerns for science and society alike. Potentially, ecosystems show nonlinear responses to land-use intensification that would open management options with limited ecological losses but satisfying economic gains. However, multidisciplinary studies to quantify ecological losses and socioeconomic tradeoffs under different management options are rare. Here, we evaluate opposing land use strategies in cacao agroforestry in Sulawesi, Indonesia, by using data on species richness of nine plant and animal taxa, six related ecosystem functions, and on socioeconomic drivers of agroforestry expansion. Expansion of cacao cultivation by 230% in the last two decades was triggered not only by economic market mechanisms, but also by rarely considered cultural factors. Transformation from near-primary forest to agroforestry had little effect on overall species richness, but reduced plant biomass and carbon storage by ≈75% and species richness of forest-using species by ≈60%. In contrast, increased land use intensity in cacao agroforestry, coupled with a reduction in shade tree cover from 80% to 40%, caused only minor quantitative changes in biodiversity and maintained high levels of ecosystem functioning while doubling farmers' net income. However, unshaded systems further increased income by ≈40%, implying that current economic incentives and cultural preferences for new intensification practices put shaded systems at risk. We conclude that low-shade agroforestry provides the best available compromise between economic forces and ecological needs. Certification schemes for shade-grown crops may provide a market-based mechanism to slow down current intensification trends. PMID:17360392

Tradeoffs between income, biodiversity, and ecosystem functioning during tropical rainforest conversion and agroforestry intensification.

PubMed

Steffan-Dewenter, Ingolf; Kessler, Michael; Barkmann, Jan; Bos, Merijn M; Buchori, Damayanti; Erasmi, Stefan; Faust, Heiko; Gerold, Gerhard; Glenk, Klaus; Gradstein, S Robbert; Guhardja, Edi; Harteveld, Marieke; Hertel, Dietrich; Höhn, Patrick; Kappas, Martin; Köhler, Stefan; Leuschner, Christoph; Maertens, Miet; Marggraf, Rainer; Migge-Kleian, Sonja; Mogea, Johanis; Pitopang, Ramadhaniel; Schaefer, Matthias; Schwarze, Stefan; Sporn, Simone G; Steingrebe, Andrea; Tjitrosoedirdjo, Sri S; Tjitrosoemito, Soekisman; Twele, André; Weber, Robert; Woltmann, Lars; Zeller, Manfred; Tscharntke, Teja

2007-03-20

Losses of biodiversity and ecosystem functioning due to rainforest destruction and agricultural intensification are prime concerns for science and society alike. Potentially, ecosystems show nonlinear responses to land-use intensification that would open management options with limited ecological losses but satisfying economic gains. However, multidisciplinary studies to quantify ecological losses and socioeconomic tradeoffs under different management options are rare. Here, we evaluate opposing land use strategies in cacao agroforestry in Sulawesi, Indonesia, by using data on species richness of nine plant and animal taxa, six related ecosystem functions, and on socioeconomic drivers of agroforestry expansion. Expansion of cacao cultivation by 230% in the last two decades was triggered not only by economic market mechanisms, but also by rarely considered cultural factors. Transformation from near-primary forest to agroforestry had little effect on overall species richness, but reduced plant biomass and carbon storage by approximately 75% and species richness of forest-using species by approximately 60%. In contrast, increased land use intensity in cacao agroforestry, coupled with a reduction in shade tree cover from 80% to 40%, caused only minor quantitative changes in biodiversity and maintained high levels of ecosystem functioning while doubling farmers' net income. However, unshaded systems further increased income by approximately 40%, implying that current economic incentives and cultural preferences for new intensification practices put shaded systems at risk. We conclude that low-shade agroforestry provides the best available compromise between economic forces and ecological needs. Certification schemes for shade-grown crops may provide a market-based mechanism to slow down current intensification trends.

High-quality remote interactive imaging in the operating theatre

NASA Astrophysics Data System (ADS)

Grimstead, Ian J.; Avis, Nick J.; Evans, Peter L.; Bocca, Alan

2009-02-01

We present a high-quality display system that enables the remote access within an operating theatre of high-end medical imaging and surgical planning software. Currently, surgeons often use printouts from such software for reference during surgery; our system enables surgeons to access and review patient data in a sterile environment, viewing real-time renderings of MRI & CT data as required. Once calibrated, our system displays shades of grey in Operating Room lighting conditions (removing any gamma correction artefacts). Our system does not require any expensive display hardware, is unobtrusive to the remote workstation and works with any application without requiring additional software licenses. To extend the native 256 levels of grey supported by a standard LCD monitor, we have used the concept of "PseudoGrey" where slightly off-white shades of grey are used to extend the intensity range from 256 to 1,785 shades of grey. Remote access is facilitated by a customized version of UltraVNC, which corrects remote shades of grey for display in the Operating Room. The system is successfully deployed at Morriston Hospital, Swansea, UK, and is in daily use during Maxillofacial surgery. More formal user trials and quantitative assessments are being planned for the future.

Prevalence of Tooth Shade and its Correlation with Skin Colour - A Cross-sectional Study.

PubMed

Vadavadagi, Suneel V; Kumari, K V Halini; Choudhury, Gopal Krishna; Vilekar, Abhishek Madhukar; Das, Sitansu Sekhar; Jena, Debkant; Kataraki, Bharat; B L, Bhavana

2016-02-01

Aesthetics has become an important issue in modern society. Tooth shade is one of the factors in determining aesthetics. Studies have revealed that tooth shade is influenced by age, gender, eye colour, skin colour and other factors. The present study was aimed to assess the prevalence of tooth shade and its correlation with skin colour. A total of 300 subjects aged 18-20 years were evaluated for tooth shade using Vitapan - 3D shade guide. Anterior teeth were checked under natural light and facial skin colour by Lakme liquid foundation make up as a shade guide. Data was analysed using chi square test and spearman's correlation. Out of 300 students, 114 (38.00%) had A2 tooth shade; the least prevalent tooth shade among Chitradurga population was C1 (4.00%). There was a positive correlation between tooth shade and skin colour which was found to be statistically significant (p <0.05). The most prevalent tooth shade among Chitradurga population was A2 and least was C1. There was a significant correlation between tooth shade and skin colour with lighter skin tone subjects having lighter tooth shade hence skin colour can be used as a guide for shade selection.

Effect of individual shades on reliability and validity of observers in colour matching.

PubMed

Lagouvardos, P E; Diamanti, H; Polyzois, G

2004-06-01

The effect of individual shades in shade guides, on the reliability and validity of measurements in a colour matching process is very important. Observer's agreement on shades and sensitivity/specificity of shades, can give us an estimate of shade's effect on observer's reliability and validity. In the present study, a group of 16 students, matched 15 shades of a Kulzer's guide and 10 human incisors to Kulzer's and/or Vita's shade tabs, in 4 different tests. The results showed shades I, B10, C40, A35 and A10 were those with the highest reliability and validity values. In conclusion, a) the matching process with shades of different materials was not accurate enough, b) some shades produce a more reliable and valid match than others and c) teeth are matched with relative difficulty.

Shade guide optimization--a novel shade arrangement principle for both ceramic and composite shade guides when identifying composite test objects.

PubMed

Østervemb, Niels; Jørgensen, Jette Nedergaard; Hørsted-Bindslev, Preben

2011-02-01

The most widely used shade guide for composite materials is made of ceramic and arranged according to a non-proven method. There is a need for a composite shade guide using a scientifically based arrangement principle. To compare the shade tab arrangement of the Vitapan Classical shade guide and an individually made composite shade guide using both the originally proposed arrangement principle and arranged according to ΔE2000 values with hue group division. An individual composite shade guide made from Filtek Supreme XT body colors was compared to the Vitapan Classical shade guide. Twenty-five students matched color samples made from Filtek Supreme XT body colors using the two shade guides arranged after the two proposed principles--four shade guides in total. Age, sequence, gender, time, and number of correct matches were recorded. The proposed visually optimal composite shade guide was both fastest and had the highest number of correct matches. Gender was significantly associated with time used for color sampling but not regarding the number of correct shade matches. A composite shade guide is superior compared to the ceramic Vitapan Classical guide when using composite test objects. A rearrangement of the shade guide according to hue, subdivided according to ΔE2000, significantly reduces the time needed to take a color sample and increases the number of correct shade matches. Total color difference in relation to the lightest tab with hue group division is recommended as a possible and universally applicable mode of tab arrangement in dental color standards. Moreover, a shade guide made of the composite materials itself is to be preferred as both a faster and more accurate method of determining color. © 2011, COPYRIGHT THE AUTHORS. JOURNAL COMPILATION © 2011, WILEY PERIODICALS, INC.

EXAMINING THE PREFERENCE FOR SHADE STRUCTURES IN FARMED GREEN SEA TURTLES (CHELONIA MYDAS) AND SHADE'S EFFECT ON GROWTH AND TEMPERATURES.

PubMed

Keller, Martha; Mustin, Walter

2017-03-01

The Cayman Turtle Farm raises thousands of green sea turtles ( Chelonia mydas ) annually under aquaculture conditions. Historically, the turtles have been raised in tanks without routine access to a shade structure. The purpose of this study was to determine the effects of adding a shade structure on curved carapace length (CCL) and weight gain of green sea turtles. In addition, water and cloacal temperatures were compared across treatment groups and shade cover preferences observed. Ninety turtles were split equally into three treatment groups for this 8-wk study. In the first group turtles were kept in tanks in full sun, the second group in half-shaded tanks, and the third group in tanks completely covered with shade cloth. Time-lapse cameras mounted above half-shaded tanks were used to determine turtle shade structure preferences throughout the day. There were no differences in CCL among treatment groups. Significant increases in weights were noted in turtles kept in full sun and half-shaded tanks versus the fully shaded tanks. Significantly higher water and cloacal turtle temperatures were noted in the full-sun tank compared with the half-shaded or completely shaded tanks. A significantly lower number of turtles was observed in the sun in the half-shaded tanks, indicating a possible preference by turtles for a shade structure. Results suggest that providing shade structures for sea turtles results in a significant decrease in both overall water temperature as well as a reduction in maximum high daily temperatures. Results also suggest that turtles exhibit a preference for shade structures when it is provided as an option. From these results, we recommend that a shade structure be provided when housing green sea turtles in outdoor enclosures.

Dark current reduction of Ge photodetector by GeO₂ surface passivation and gas-phase doping.

PubMed

Takenaka, Mitsuru; Morii, Kiyohito; Sugiyama, Masakazu; Nakano, Yoshiaki; Takagi, Shinichi

2012-04-09

We have investigated the dark current of a germanium (Ge) photodetector (PD) with a GeO₂ surface passivation layer and a gas-phase-doped n+/p junction. The gas-phase-doped PN diodes exhibited a dark current of approximately two orders of magnitude lower than that of the diodes formed by a conventional ion implantation process, indicating that gas-phase doping is suitable for low-damage PN junction formation. The bulk leakage (Jbulk) and surface leakage (Jsurf) components of the dark current were also investigated. We have found that GeO₂ surface passivation can effectively suppress the dark current of a Ge PD in conjunction with gas-phase doping, and we have obtained extremely low values of Jbulk of 0.032 mA/cm² and Jsurf of 0.27 μA/cm.

Detection of free liquid in drums of radioactive waste. [Patent application

DOEpatents

Not Available

1979-10-16

A nondestructive thermal imaging method for detecting the presence of a liquid such as water within a sealed container is described. The process includes application of a low amplitude heat pulse to an exterior surface area of the container, terminating the heat input and quickly mapping the resulting surface temperatures. The various mapped temperature values can be compared with those known to be normal for the container material and substances in contact. The mapped temperature values show up in different shades of light or darkness that denote different physical substances. The different substances can be determined by direct observation or by comparison with known standards. The method is particularly applicable to the detection of liquids above solidified radioactive wastes stored in sealed containers.

Location of Sites Within 'Cryptic Terrain'

NASA Technical Reports Server (NTRS)

2007-01-01

A regional landscape near Mars' south pole is called 'cryptic terrain' because it once defied explanation, but new observations bolster and refine interpretations of how springtime outbursts of carbon-dioxide gas there sculpt intricate patterns and paint seasonal splotches. This map indicates locations of three sites that have been examined within the area of cryptic terrain, informally designated 'Manhattan,' 'Giza' and 'Ithaca.'

The underlying map offers context of brightness measurements from the Thermal Emission Spectrometer instrument draped over a shaded relief map based on data from the Mars Orbiter Laser Altimeter instrument. Cool colors are areas with a low albedo (dark) and warm colors are areas which have high albedo (bright). Both of those instruments flew on NASA's Mars Global Surveyor orbiter.

Evaluation of Dental Shade Guide Variability Using Cross-Polarized Photography.

PubMed

Gurrea, Jon; Gurrea, Marta; Bruguera, August; Sampaio, Camila S; Janal, Malvin; Bonfante, Estevam; Coelho, Paulo G; Hirata, Ronaldo

2016-01-01

This study evaluated color variability in the A hue between the VITA Classical (VITA Zahnfabrik) shade guide and four other VITA-coded ceramic shade guides using a Canon EOS 60D camera and software (Photoshop CC, Adobe). A total of 125 photographs were taken, 5 per shade tab for each of 5 shades (A1 to A4) from the following shade guides: VITA Classical (control), IPS e.max Ceram (Ivoclar Vivadent), IPS d.SIGN (Ivoclar Vivadent), Initial ZI (GC), and Creation CC (Creation Willi Geller). Photos were processed with Adobe Photoshop CC to allow standardized evaluation of hue, chroma, and value between shade tabs. None of the VITA-coded shade tabs fully matched the VITA Classical shade tab for hue, chroma, or value. The VITA-coded shade guides evaluated herein showed an overall unmatched shade in all tabs when compared with the control, suggesting that shade selection should be made using the guide produced by the manufacturer of the ceramic intended for the final restoration.

Hot spots and dark current in advanced plasma wakefield accelerators

DOE PAGES

Manahan, G. G.; Deng, A.; Karger, O.; ...

2016-01-29

Dark current can spoil witness bunch beam quality and acceleration efficiency in particle beam-driven plasma wakefield accelerators. In advanced schemes, hot spots generated by the drive beam or the wakefield can release electrons from higher ionization threshold levels in the plasma media. Likewise, these electrons may be trapped inside the plasma wake and will then accumulate dark current, which is generally detrimental for a clear and unspoiled plasma acceleration process. The strategies for generating clean and robust, dark current free plasma wake cavities are devised and analyzed, and crucial aspects for experimental realization of such optimized scenarios are discussed.

Intrarater repeatability of shade selections with two shade guides.

PubMed

Hammad, Ihab A

2003-01-01

Color research has shown that shade guides do not always represent the color of natural teeth. Moreover, visual evaluation has been found to be unreliable and inconsistent. This investigation evaluated the effects of 2 shade guides on the intrarater repeatability (reliability) of prosthodontists and general practitioners with regard to shade selection. Ten prosthodontists and ten general practitioners (all men, 35-45 years old) with an average practice experience of 14 years participated in this study. Examiners were tested to eliminate color blindness. Each clinician used Vita Lumin Vacuum and Vitapan 3D-Master shade guides to determine the shades of the maxillary right canines of 20 patients following a standard protocol. The identification codes of the shade tabs were masked to prevent shade memory. All teeth were polished before each shade selection, and the selection process was standardized for controlled lighting and procedures. Shade selections were randomly repeated 1 month later by the same practitioners on the same group of patients in accordance with the same shade-selection protocol. Analysis of variance and t tests for individual comparisons among means were performed (P<.05). Significant interactions were found between the effects of shade guide system and specialty training on intrarater repeatability (P<.0001, analysis of variance). The intrarater repeatability of prosthodontists was significantly higher than that of general practitioners when the Vita Lumin Vacuum shade guide was used (P<.0001, t test). Use of the Vitapan 3D-Master shade guide significantly improved the intrarater repeatability of general practitioners compared with the Vita Lumin Vacuum shade guide (P<.0005). This improvement was not significant, however, among prosthodontists (P=.2861). Within the limitations of this study, the prosthodontists demonstrated superior intrarater repeatability in shade selection, especially when the Vita Lumin Vacuum shade guide was used. Use of the Vitapan 3D-Master shade guide notably improved intrarater repeatability among the general practitioners.

Evaluation of a standard shade guide for color change after disinfection.

PubMed

Pohjola, Randall M; Hackman, Steven T; Browning, William D

2007-09-01

To determine if surface disinfectants cause a change in the shade perception of a standard Classic Vitapan shade guide. Consistency in shade selection for dental restorations involves many factors, and one of the most important is the shade tabs used in the selection process. Ten shade tabs each of shades B2, D2, C1, and A3.5 were selected from the Classic Vitapan shade guide (Vident). All tabs were measured with the EasyShade shade device (Vident) at baseline. Three tabs of each shade were set aside as controls. The other 7 tabs of each shade were treated with the surface disinfectant Cavicide (Metrex Research) for 480 cycles to simulate a year's usage. After each 480 cycles, all the tabs were again measured with the EasyShade. This process was repeated to simulate 2 and 3 years of use. The data were analyzed to calculate the delta E 2000 for any change. A statistically significant increase was observed in the value (L*) and chroma (C*) after 2 and 3 years of simulated treatments. These changes were not perceptible to the clinician. The authors suggest that 1 standard shade guide be set aside to compare against those in clinical use to determine when they should be replaced.

Dark Current Reduction of IR Detectors

DTIC Science & Technology

2017-10-19

demonstrating a novel dark current reduction approach for dense infrared detector arrays. This technique is based on the diffusion control junction (DCJ...fabricate and test detector arrays with and without DCJs on the same wafer and demonstrate the effectiveness of the DCJ approach in reducing dark current...subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE

Effects of elevated atmospheric CO2 concentration on leaf dark respiration of Xanthium strumarium in light and in darkness

PubMed Central

Wang, Xianzhong; Lewis, James D.; Tissue, David T.; Seemann, Jeffrey R.; Griffin, Kevin L.

2001-01-01

Leaf dark respiration (R) is an important component of plant carbon balance, but the effects of rising atmospheric CO2 on leaf R during illumination are largely unknown. We studied the effects of elevated CO2 on leaf R in light (RL) and in darkness (RD) in Xanthium strumarium at different developmental stages. Leaf RL was estimated by using the Kok method, whereas leaf RD was measured as the rate of CO2 efflux at zero light. Leaf RL and RD were significantly higher at elevated than at ambient CO2 throughout the growing period. Elevated CO2 increased the ratio of leaf RL to net photosynthesis at saturated light (Amax) when plants were young and also after flowering, but the ratio of leaf RD to Amax was unaffected by CO2 levels. Leaf RN was significantly higher at the beginning but significantly lower at the end of the growing period in elevated CO2-grown plants. The ratio of leaf RL to RD was used to estimate the effect of light on leaf R during the day. We found that light inhibited leaf R at both CO2 concentrations but to a lesser degree for elevated (17–24%) than for ambient (29–35%) CO2-grown plants, presumably because elevated CO2-grown plants had a higher demand for energy and carbon skeletons than ambient CO2-grown plants in light. Our results suggest that using the CO2 efflux rate, determined by shading leaves during the day, as a measure for leaf R is likely to underestimate carbon loss from elevated CO2-grown plants. PMID:11226264

Effects of elevated atmospheric CO2 concentration on leaf dark respiration of Xanthium strumarium in light and in darkness.

PubMed

Wang, X; Lewis, J D; Tissue, D T; Seemann, J R; Griffin, K L

2001-02-27

Leaf dark respiration (R) is an important component of plant carbon balance, but the effects of rising atmospheric CO(2) on leaf R during illumination are largely unknown. We studied the effects of elevated CO(2) on leaf R in light (R(L)) and in darkness (R(D)) in Xanthium strumarium at different developmental stages. Leaf R(L) was estimated by using the Kok method, whereas leaf R(D) was measured as the rate of CO(2) efflux at zero light. Leaf R(L) and R(D) were significantly higher at elevated than at ambient CO(2) throughout the growing period. Elevated CO(2) increased the ratio of leaf R(L) to net photosynthesis at saturated light (A(max)) when plants were young and also after flowering, but the ratio of leaf R(D) to A(max) was unaffected by CO(2) levels. Leaf R(N) was significantly higher at the beginning but significantly lower at the end of the growing period in elevated CO(2)-grown plants. The ratio of leaf R(L) to R(D) was used to estimate the effect of light on leaf R during the day. We found that light inhibited leaf R at both CO(2) concentrations but to a lesser degree for elevated (17-24%) than for ambient (29-35%) CO(2)-grown plants, presumably because elevated CO(2)-grown plants had a higher demand for energy and carbon skeletons than ambient CO(2)-grown plants in light. Our results suggest that using the CO(2) efflux rate, determined by shading leaves during the day, as a measure for leaf R is likely to underestimate carbon loss from elevated CO(2)-grown plants.

Dark current in multilayer stabilized amorphous selenium based photoconductive x-ray detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frey, Joel B.; Belev, George; Kasap, Safa O.

2012-07-01

We report on experimental results which show that the dark current in n-i-p structured, amorphous selenium films is independent of i-layer thickness in samples with consistently thick blocking layers. We have observed, however, a strong dependence on the n-layer thickness and positive contact metal chosen. These results indicate that the dominant source of the dark current is carrier injection from the contacts and any contribution from carriers thermally generated in the bulk of the photoconductive layer is negligible. This conclusion is supported by a description of the dark current transients at different applied fields by a model which assumes onlymore » carrier emission over a Schottky barrier. This model also predicts that while hole injection is initially dominant, some time after the application of the bias, electron injection may become the dominant source of dark current.« less

Sun shield

NASA Technical Reports Server (NTRS)

Frank, Arthur M. (Inventor); Derespinis, Silvio F. (Inventor); Mockovciak, John, Jr. (Inventor)

1987-01-01

A shading device which is capable of compactly storing a flexible shade on a biased, window shade type spring roller is disclosed. It is controlled to deliver the shade selectively to either its operative shading or compact storage orientation.

Shade determination using camouflaged visual shade guides and an electronic spectrophotometer.

PubMed

Kvalheim, S F; Øilo, M

2014-03-01

The aim of the present study was to compare a camouflaged visual shade guide to a spectrophotometer designed for restorative dentistry. Two operators performed analyses of 66 subjects. One central upper incisor was measured four times by each operator; twice with a camouflaged visual shade guide and twice with a spectrophotometer Both methods had acceptable repeatability rates, but the electronic shade determination showed higher repeatability. In general, the electronically determined shades were darker than the visually determined shades. The use of a camouflaged visual shade guide seems to be an adequate method to reduce operator bias.

Shaded-Color Picture Generation of Computer-Defined Arbitrary Shapes

NASA Technical Reports Server (NTRS)

Cozzolongo, J. V.; Hermstad, D. L.; Mccoy, D. S.; Clark, J.

1986-01-01

SHADE computer program generates realistic color-shaded pictures from computer-defined arbitrary shapes. Objects defined for computer representation displayed as smooth, color-shaded surfaces, including varying degrees of transparency. Results also used for presentation of computational results. By performing color mapping, SHADE colors model surface to display analysis results as pressures, stresses, and temperatures. NASA has used SHADE extensively in sign and analysis of high-performance aircraft. Industry should find applications for SHADE in computer-aided design and computer-aided manufacturing. SHADE written in VAX FORTRAN and MACRO Assembler for either interactive or batch execution.

Nonlinear time dependence of dark current in charge-coupled devices

NASA Astrophysics Data System (ADS)

Dunlap, Justin C.; Bodegom, Erik; Widenhorn, Ralf

2011-03-01

It is generally assumed that charge-coupled device (CCD) imagers produce a linear response of dark current versus exposure time except near saturation. We found a large number of pixels with nonlinear dark current response to exposure time to be present in two scientific CCD imagers. These pixels are found to exhibit distinguishable behavior with other analogous pixels and therefore can be characterized in groupings. Data from two Kodak CCD sensors are presented for exposure times from a few seconds up to two hours. Linear behavior is traditionally taken for granted when carrying out dark current correction and as a result, pixels with nonlinear behavior will be corrected inaccurately.

Low dark current InGaAs detector arrays for night vision and astronomy

NASA Astrophysics Data System (ADS)

MacDougal, Michael; Geske, Jon; Wang, Chad; Liao, Shirong; Getty, Jonathan; Holmes, Alan

2009-05-01

Aerius Photonics has developed large InGaAs arrays (1K x 1K and greater) with low dark currents for use in night vision applications in the SWIR regime. Aerius will present results of experiments to reduce the dark current density of their InGaAs detector arrays. By varying device designs and passivations, Aerius has achieved a dark current density below 1.0 nA/cm2 at 280K on small-pixel, detector arrays. Data is shown for both test structures and focal plane arrays. In addition, data from cryogenically cooled InGaAs arrays will be shown for astronomy applications.

Ultra-Fast Image Sensor Using Ge on Insulator MIS/Schottky Detectors

DTIC Science & Technology

2008-05-28

electronic system. The noise equivalent power is defined as in /R, where in is the current noise and R is the responsivity. At 1 V, the current noise ...is limited by the dark current and can be approximated as the shot noise 2eIdf1/2, where Id is the measured dark current. At 0 V, the dark current...approaches zero, and the current noise should be approximated as Johnson noise 4kTGf1/2, where G is the measured conductance. Therefore, D* can be

Identifying outdoor thermal risk areas and evaluation of future thermal comfort concerning shading orientation in a traditional settlement.

PubMed

Huang, Kuo-Tsang; Yang, Shing-Ru; Matzarakis, Andreas; Lin, Tzu-Ping

2018-06-01

The outdoor thermal environment is expected to be deteriorated under climate change. An approach of risk identification including assessment from aspects of thermal stress effect, people's exposure, and local's vulnerability were adopted to study a hot-and-humid traditional rural community located at Tainan, Taiwan. Layers of each aspect were either constructed by in-situ measurements or simulations. To evaluate the future thermal comfort changes by simulations, the prerequisite hourly climate data of three future time slices were produced. Prognostic simulation model, ENVI-met, in combination with diagnostic model, RayMan, were respectively used for identifying current spatial distribution of thermal stress and for assessing the future thermal comfort changes. High thermal risk area was identified by superimposing layers of hazard, exposure and vulnerability. It revealed that because of the tourists' vulnerability to adapt local climate and the inflexibleness of choosing visiting time, it exhibited a high thermal stress at the Main Courtyard where its thermal comfort conditions will be deteriorated due to climate change. Furthermore, the thermal comfort conditions in various shading orientation were analyzed based on the changing climate in three future time slices, i.e. 2011-2040, 2041-2070, and 2071-2100. The results show the area with shading in the East and West side is more comfort than in the North side. In hot season, shading in the West side contributes less PET increasing, especially in the afternoon period. The severest overheat problem (the physiological equivalent temperature, PET>40°C) at the Main Courtyard will increase from current 10% to 28% in 2071-2100 in terms of overheating occurrence frequency. The results of this study can be used as the guidelines for environment analysis before planning or redesign community. Copyright © 2018 Elsevier B.V. All rights reserved.

In Situ observation of dark current emission in a high gradient rf photocathode gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shao, Jiahang; Shi, Jiaru; Antipov, Sergey P.

Undesirable electron field emission (also known as dark current) in high gradient rf photocathode guns deteriorates the quality of the photoemission current and limits the operational gradient. To improve the understanding of dark current emission, a high-resolution (~100 μm) dark current imaging experiment has been performed in an L-band photocathode gun operating at ~100 MV/m of surface gradient. Scattered strong emission areas with high current have been observed on the cathode. The field enhancement factor β of selected regions on the cathode has been measured. Finally, the postexaminations with scanning electron microscopy and white light interferometry reveal the origins ofmore » ~75% strong emission areas overlap with the spots where rf breakdown has occurred.« less

In Situ observation of dark current emission in a high gradient rf photocathode gun

DOE PAGES

Shao, Jiahang; Shi, Jiaru; Antipov, Sergey P.; ...

2016-08-15

Undesirable electron field emission (also known as dark current) in high gradient rf photocathode guns deteriorates the quality of the photoemission current and limits the operational gradient. To improve the understanding of dark current emission, a high-resolution (~100 μm) dark current imaging experiment has been performed in an L-band photocathode gun operating at ~100 MV/m of surface gradient. Scattered strong emission areas with high current have been observed on the cathode. The field enhancement factor β of selected regions on the cathode has been measured. Finally, the postexaminations with scanning electron microscopy and white light interferometry reveal the origins ofmore » ~75% strong emission areas overlap with the spots where rf breakdown has occurred.« less

Response of the Fine Root Production, Phenology, and Turnover Rate of Six Shrub Species from a Subtropical Forest to a Soil Moisture Gradient and Shading

NASA Astrophysics Data System (ADS)

Fu, X.; Dai, X.; Wang, H.

2015-12-01

Knowledge of the fine root dynamics of different life forms in forest ecosystems is critical to understanding how the overall belowground carbon cycling is affected by climate change. However, our current knowledge regarding how endogenous or exogenous factors regulate the root dynamics of understory vegetation is limited. We selected a suite of study sites representing different habitats with gradients of soil moisture and solar radiation (shading or no shading). We assessed the fine root production phenology, the total fine root production, and the turnover among six understory shrub species in a subtropical climate, and examined the responses of the fine root dynamics to gradients in the soil moisture and solar radiation. The shrubs included three evergreen species, Loropetalum chinense, Vaccinium bracteatum, and Adinandra millettii, and three deciduous species, Serissa serissoides, Rubus corchorifolius, and Lespedeza davidii. We observed that variations in the annual fine root production and turnover among species were significant in the deciduous group but not in the evergreen group. Notably, V. bracteatum and S. serissoides presented the greatest responses in terms of root phenology to gradients in the soil moisture and shading: high-moisture habitat led to a decrease and shade led to an increase in fine root production during spring. Species with smaller fine roots of the 1st+2nd-order diameter presented more sensitive responses in terms of fine root phenology to a soil moisture gradient. Species with a higher fine root nitrogen-to -carbon ratio exhibited more sensitive responses in terms of fine root annual production to shading. Soil moisture and shading did not change the annual fine root production as much as the turnover rate. The fine root dynamics of some understory shrubs varied significantly with soil moisture and solar radiation status and may be different from tree species. Our results emphasize the need to study the understory fine root dynamics in the achievement of a complete understanding of the overall belowground carbon cycling in a forest ecosystem, particularly ecosystems in which the understory fine root highly contributes to the belowground biomass.

Evaluation of reliability and validity of three dental color-matching devices.

PubMed

Tsiliagkou, Aikaterini; Diamantopoulou, Sofia; Papazoglou, Efstratios; Kakaboura, Afrodite

2016-01-01

To assess the repeatability and accuracy of three dental color-matching devices under standardized and freehand measurement conditions. Two shade guides (Vita Classical A1-D4, Vita; and Vita Toothguide 3D-Master, Vita), and three color-matching devices (Easyshade, Vita; SpectroShade, MHT Optic Research; and ShadeVision, X-Rite) were used. Five shade tabs were selected from the Vita Classical A1-D4 (A2, A3.5, B1, C4, D3), and five from the Vita Toothguide 3D-Master (1M1, 2R1.5, 3M2, 4L2.5, 5M3) shade guides. Each shade tab was recorded 15 continuous, repeated times with each device under two different measurement conditions (standardized, and freehand). Both qualitative (color shade) and quantitative (L, a, and b) color characteristics were recorded. The color difference (ΔE) of each recorded value with the known values of the shade tab was calculated. The repeatability of each device was evaluated by the coefficient of variance. The accuracy of each device was determined by comparing the recorded values with the known values of the reference shade tab (one sample t test; α = 0.05). The agreement between the recorded shade and the reference shade tab was calculated. The influence of the parameters (devices and conditions) on the parameter ΔE was investigated (two-way ANOVA). Comparison of the devices was performed with Bonferroni pairwise post-hoc analysis. Under standardized conditions, repeatability of all three devices was very good, except for ShadeVision with Vita Classical A1-D4. Accuracy ranged from good to fair, depending on the device and the shade guide. Under freehand conditions, repeatability and accuracy for Easyshade and ShadeVision were negatively influenced, but not for SpectroShade, regardless of the shade guide. Based on the total of the color parameters assessed per device, SpectroShade was the most reliable of the three color-matching devices studied.

Stainless steel in coastal seawater: sunlight counteracts biologically enhanced cathodic kinetics.

PubMed

Eashwar, M; Lakshman Kumar, A; Sreedhar, G; Kennedy, J; Suresh Bapu, R H

2014-09-01

The influence of sunlight of varying intensity on the performance of UNS S30400 stainless steel (SS) was explored under conditions of natural biofilm development in coastal seawater. In a series of tests performed outdoors under an opaque roof, a range of shades were fashioned to impart varied amounts of diurnal light. These were an ambient level where the underwater illumination was ~ 5% of full sunlight, two intermediate ranges of lighting with ~ 2.5% and ~ 1% of the daylight, and a condition of full darkness. In comparison with the dark, increments of sunlight rendered the SS progressively less aggressive as cathodes in galvanic couples with UNS C70600 alloy. Likewise, welded SS with pre-initiated localized corrosion sites exhibited substantially lower rates of propagation with light. Thus, biofilms and sunlight affected cathodic kinetics in opposite ways. Surface analytical tests showed that the accumulation of manganese (Mn) within the biofilms was small relative to reports from waters of lower salinity. These results not only reveal that extremely low amounts of sunlight are adequate to offset the microbial effect, but also highlight the lack of convincing evidence for Mn cycling as a potent mechanism for enhanced cathodic kinetics in full-strength seawater.

Heat stress in cows at pasture and benefit of shade in a temperate climate region

NASA Astrophysics Data System (ADS)

Veissier, Isabelle; Van laer, Eva; Palme, Rupert; Moons, Christel P. H.; Ampe, Bart; Sonck, Bart; Andanson, Stéphane; Tuyttens, Frank A. M.

2017-11-01

Under temperate climates, cattle are often at pasture in summer and are not necessarily provided with shade. We aimed at evaluating in a temperate region (Belgium) to what extent cattle may suffer from heat stress (measured through body temperature, respiration rate and panting score, cortisol or its metabolites in milk, and feces on hot days) and at assessing the potential benefits of shade. During the summer of 2012, 20 cows were kept on pasture without access to shade. During the summer of 2011, ten cows had access to shade (young trees with shade cloth hung between them), whereas ten cows had no access. Climatic conditions were quantified by the Heat Load Index (HLI). In animals without access to shade respiration rates, panting scores, rectal temperatures, and milk cortisol concentrations increased as HLI increased in both 2011 and 2012. Fecal cortisol metabolites varied with HLI in 2011 only. When cattle had access to shade, their use of shade increased as the HLI increased. This effect was more pronounced during the last part of the summer, possibly due to better acquaintance with the shade construction. In this case, shade use increased to 65% at the highest HLI (79). Shade tempered the effects on respiration, rectal temperature, and fecal cortisol metabolites. Milk cortisol was not influenced by HLI for cows using shade for > 10% of the day. Therefore, even in temperate areas, cattle may suffer from heat when they are at pasture in summer and providing shade can reduce such stress.

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2010-11-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m by 6.0 m by 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2009-11-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m by 6.0 m by 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Shade material evaluation using a cattle response model and meteorological instrumentation.

PubMed

Eigenberg, Roger A; Brown-Brandl, Tami M; Nienaber, John A

2010-09-01

Shade structures are often considered as one method of reducing stress in feedlot cattle. Selection of a suitable shade material can be difficult without data that quantify material effectiveness for stress reduction. A summer study was conducted during 2007 using instrumented shade structures in conjunction with meteorological measurements to estimate relative effectiveness of various shade materials. Shade structures were 3.6 m x 6.0 m x 3.0 m high at the peak and 2.0 m high at the sides. Polyethylene shade cloth was used in three of the comparisons and consisted of effective coverings of 100%, 60% with a silver reflective coating, and 60% black material with no reflective coating. Additionally, one of the structures was fitted with a poly snow fence with an effective shade of about 30%. Each shade structure contained a solar radiation meter and a black globe thermometer to measure radiant energy received under the shade material. Additionally, meteorological data were collected as a non-shaded treatment and included temperature, humidity, wind speed, and solar radiation. Data analyses was conducted using a physiological model based on temperature, humidity, solar radiation and wind speed; a second model using black globe temperatures, relative humidity, and wind speed was used as well. Analyses of the data revealed that time spent in the highest stress category was reduced by all shade materials. Moreover, significant differences (P < 0.05) existed between all shade materials (compared to no-shade) for hourly summaries during peak daylight hours and for 'full sun' days.

Role of riparian shade on the fish assemblage of a reservoir littoral

USGS Publications Warehouse

Raines, C. D.; Miranda, Leandro E.

2016-01-01

Research into the effects of shade on reservoir fish assemblages is lacking, with most investigations focused on streams. Unlike many streams, the canopy in a reservoir shades only a narrow fringe of water adjacent to the shoreline, and may not have the influential effect on the aquatic environment reported in streams. We compared fish assemblages between shaded and unshaded sites in a shallow reservoir. Overall species richness (gamma diversity) was higher in shaded sites, and fish assemblage composition differed between shaded and unshaded sites. Average light intensity was 66 % lower in shaded sites, and differences in average temperature and dissolved oxygen were small. Unlike streams where shade can have large effects on water physicochemistry, in reservoirs shade-related differences in fish assemblages seemed to be linked principally to differences in light intensity. Diversity in light intensity in shaded and unshaded sites in reservoirs can create various mosaics of light-based habitats that enable diversity of species assemblages. Managing to promote the habitat diversity provided by shade may require coping with the artificial nature of reservoir riparian zones and water level fluctuations.

WFC3/UVIS Dark Calibration: Monitoring Results and Improvements to Dark Reference Files

NASA Astrophysics Data System (ADS)

Bourque, M.; Baggett, S.

2016-04-01

The Wide Field Camera 3 (WFC3) UVIS detector possesses an intrinsic signal during exposures, even in the absence of light, known as dark current. A daily monitor program is employed every HST cycle to characterize and measure this current as well as to create calibration files which serve to subtract the dark current from science data. We summarize the results of the daily monitor program for all on-orbit data. We also introduce a new algorithm for generating the dark reference files that provides several improvements to their overall quality. Key features to the new algorithm include correcting the dark frames for Charge Transfer Efficiency (CTE) losses, using an anneal-cycle average value to measure the dark current, and generating reference files on a daily basis. This new algorithm is part of the release of the CALWF3 v3.3 calibration pipeline on February 23, 2016 (also known as "UVIS 2.0"). Improved dark reference files have been regenerated and re-delivered to the Calibration Reference Data System (CRDS) for all on-orbit data. Observers with science data taken prior to the release of CALWF3 v3.3 may request their data through the Mikulski Archive for Space Telescopes (MAST) to obtain the improved products.

Radiometric and Radiation Response of Visible FPAs

NASA Technical Reports Server (NTRS)

Hubbs, John

2007-01-01

The readout integrated circuit (ROIC) used in these devices was originally developed for use in space based infrared systems operating at deep cryogenic temperatures and was selected because of its proven tolerance to total ionizing radiation? The detectors are a 128 x 128 array of 60 pm x 60 pm pixel elements that have been anti-reflection (AR) coated to improve the response at very short wavelengths. These visible focal plane arrays were operated at -40 C (233 K). Two focal planes were characterized using cobalt-60 radiation to produce ionizing total dose damage in the VFPAs. Both operational and performance data were obtained as functions of total dose. The first device tested showed no appreciable change in responsivity or noise up to 300 krad(Si). However, at the next dose level of 600 krad(Si), the readout was non-operational due to failure in the digital circuitry. The second device was characterized to a total dose of 750 krad(Si) with no observed change in responsivity. An increase dark current was observed in both devices, and in the second device, the dark current caused an increase in noise at low irradiance at 400 krad(Si) and above. The increase in dark current was somewhat un-expected for visible PIN detectors. The median dark current increased more than two orders of magnitude at 300 krad(Si) for the first device and a factor of 350 at 750 krad(Si) for pixels near the edge for the second device. The dark current was found to be a strong function of detector bias, with pixels near the edge of the array showing a greater increase in dark current with bias than those near the center. Since the optical response was not a function of bias, it is hypothesized that the dark current is a surface effect and that the variation in dark current with location is due to a variation in pixel bias, caused by a voltage drop across the pixel common lead. As the total dose increased, the dark current and the voltage drop increased

Shade improves survival rate of outplanted 2-0 red fir seedlings

Treesearch

Donald T. Gordon

1970-01-01

Effect of shade on 2-0 red fir seedlings outplanted on the Tahoe National Forest, central California, was studied by comparing five treatments: no shade, low shade for 1 year and for 2 years, and high shade for 1 year and for 2 years. Seedlings benefited from shading-even under apparently excellent survival conditions in the first season. The extra cost of artificial...

Influence of sky view factor on outdoor thermal environment and physiological equivalent temperature

NASA Astrophysics Data System (ADS)

He, Xiaodong; Miao, Shiguang; Shen, Shuanghe; Li, Ju; Zhang, Benzhi; Zhang, Ziyue; Chen, Xiujie

2015-03-01

Sky view factor (SVF), which is an indicator of urban canyon geometry, affects the surface energy balance, local air circulation, and outdoor thermal comfort. This study focused on a continuous and long-term meteorological observation system to investigate the effects of SVF on outdoor thermal conditions and physiological equivalent temperature (PET) in the central business district (CBD) of Beijing (which is located within Chaoyang District), specifically addressed current knowledge gaps for SVF-PET relationships in cities with typical continental/microthermal climates. An urban sub-domain scale model and the RayMan model were used to diagnose wind fields and to calculate SVF and long-term PET, respectively. Analytical results show that the extent of shading contributes to variations in thermal perception distribution. Highly shaded areas (SVF <0.3) typically exhibit less frequent hot conditions during summer, while enduring longer periods of cold discomfort in winter than moderately shaded areas (0.3< SVF <0.5) and slightly shaded areas (SVF >0.5), and vice versa. Because Beijing has a monsoon-influenced humid continental climate with hot summers and long, cold, windy, and dry winters, a design project that ideally provides moderate shading should be planned to balance hot discomfort in summer and cold discomfort in winter, which effectively prolongs the comfort periods in outdoor spaces throughout the entire year. This research indicate that climate zone characteristics, urban environmental conditions, and thermal comfort requirements of residents must be accounted for in local-scale scientific planning and design, i.e., for urban canyon streets and residential estates.

Multitrait successional forest dynamics enable diverse competitive coexistence

PubMed Central

Brännström, Åke; Westoby, Mark; Dieckmann, Ulf

2017-01-01

To explain diversity in forests, niche theory must show how multiple plant species coexist while competing for the same resources. Although successional processes are widespread in forests, theoretical work has suggested that differentiation in successional strategy allows only a few species stably to coexist, including only a single shade tolerant. However, this conclusion is based on current niche models, which encode a very simplified view of plant communities, suggesting that the potential for niche differentiation has remained unexplored. Here, we show how extending successional niche models to include features common to all vegetation—height-structured competition for light under a prevailing disturbance regime and two trait-mediated tradeoffs in plant function—enhances the diversity of species that can be maintained, including a diversity of shade tolerants. We identify two distinct axes of potential niche differentiation, corresponding to the traits leaf mass per unit leaf area and height at maturation. The first axis allows for coexistence of different shade tolerances and the second axis for coexistence among species with the same shade tolerance. Addition of this second axis leads to communities with a high diversity of shade tolerants. Niche differentiation along the second axis also generates regions of trait space wherein fitness is almost equalized, an outcome we term “evolutionarily emergent near-neutrality.” For different environmental conditions, our model predicts diverse vegetation types and trait mixtures, akin to observations. These results indicate that the outcomes of successional niche differentiation are richer than previously thought and potentially account for mixtures of traits and species observed in forests worldwide. PMID:28283658

2016 Resembles Past Global Dust Storm Years on Mars

NASA Image and Video Library

2016-10-05

This graphic indicates a similarity between 2016 (dark blue line) and five past years in which Mars has experienced a global dust storm (orange lines and band), compared to years with no global dust storm (blue-green lines and band). The arrow nearly midway across in the dark blue line indicates the Mars time of year in late September 2016. A key factor in the graph is the orbital angular momentum of Mars, which would be steady in a system of only one planet orbiting the sun, but varies due to relatively small effects of having other planets in the solar system. The horizontal scale is time of year on Mars, starting at left with the planet's farthest distance from the sun in each orbit. This point in the Mars year, called "Mars aphelion," corresponds to late autumn in the southern hemisphere. Numeric values on the horizontal axis are in Earth years; each Mars year lasts for about 1.9 Earth years. The vertical scale bar at left applies only to the black-line curve on the graph. The amount of solar energy entering Mars' atmosphere (in watts per square meter) peaks at the time of year when Mars is closest to the sun, corresponding to late spring in the southern hemisphere. The duration of Mars' dust storm season, as indicated, brackets the time of maximum solar input to the atmosphere. The scale bar at right, for orbital angular momentum, applies to the blue, brown and blue-green curves on the graph. The values are based on mass, velocity and distance from the gravitational center of the solar system. Additional information on the units is in a 2015 paper in the journal Icarus, from which this graph is derived. The band shaded in orange is superimposed on the curves of angular momentum for five Mars years that were accompanied by global dust storms in 1956, 1971, 1982, 1994 and 2007. Brown diamond symbols on the curves for these years in indicate the times when the global storms began. The band shaded blue-green lies atop angular momentum curves for six years when no global dust storms occurred: 1939, 1975, 1988, 1998, 2000 and 2011. Note that in 2016, as in the pattern of curves for years with global dust storms, the start of the dust storm season corresponded to a period of increasing orbital angular momentum. In years with no global storm, angular momentum was declining at that point. Observations of whether dust from regional storms on Mars spreads globally in late 2016 or early 2017 will determine whether this correspondence holds up for the current Mars year. http://photojournal.jpl.nasa.gov/catalog/PIA20855

Effects of a shade-matching light and background color on reliability in tooth shade selection.

PubMed

Najafi-Abrandabadi, Siamak; Vahidi, Farhad; Janal, Malvin N

2018-01-01

The purpose of this study was to evaluate the effects of a shade-matching light (Rite-Lite-2, AdDent) and different viewing backgrounds on reliability in a test of shade tab matching. Four members of the Prosthodontic faculty matched 10 shade tabs selected for a range of shades against the shade guide. All raters were tested for color blindness and were calibrated prior to the study. Matching took place under four combinations of conditions: with operatory light or the shade-matching light, and using either a pink or a blue background. Reliability was quantified with the kappa statistic, separately for agreement of value, hue, and chroma for each shade tab. In general, raters showed fair to moderate levels of agreement when judging the value of the shade tabs, but could not agree on the hue and chroma of the stimuli. The pink background led to higher levels of agreement than the blue background, and the shade-matching light improved agreement when used in conjunction with the pink but not the blue background. Moderate levels of agreement were found in matching shade tab value. Agreement was generally better when using the pink rather than the blue background, regardless of light source. The use of the shade-matching light tended to amplify the advantage of the pink background.

Shading effect on generative characters of upland red rice of Southeast Sulawesi, Indonesia

NASA Astrophysics Data System (ADS)

Muhidin; Syam’un, E.; Kaimuddin; Musa, Y.; Sadimantara, G. R.; Usman; Leomo, S.; Rakian, T. C.

2018-05-01

Upland red rice (Oryza sativa) contains anthocyanin, a phenolic compounds that can act as antioxidants and functional food for human dietary. The content of functional food on upland red rice is influenced by shading condition, but the production is also influenced by environmental condition, especially the availability of light. The study aims is to assess and analyze the effect of shade on the growth and production of upland red rice. The research was conducted using the quantitative method to obtain the optimal shading condition that can increase the rice anthocyanin content and relatively high production. The research was arranged in split plot design, with shade as main plot and the different of cultivar as sub plot with three replications. The shading treatment consist of 4 levels as follows: n1=shade level < 25 %, n2=shade level 25-50%, n3=shade level 50-75% and n4=shade level > 75%. The cultivar tested were (v1) = Labandiri, (v2) = Jangkobembe, (v3) = Ranggohitam, and (v4) = Paedara. The rice planted in between teak wood trees with different age and level of canopy. The research reveals that shades had an effect in decreasing plant production (the higher level of shade, the higher the decrease level of production), but the shades can improve the quality of red rice through the increase of anthocyanin content.

Plasticity in seedling morphology, biomass allocation and physiology among ten temperate tree species in response to shade is related to shade tolerance and not leaf habit.

PubMed

Chmura, D J; Modrzyński, J; Chmielarz, P; Tjoelker, M G

2017-03-01

Mechanisms of shade tolerance in tree seedlings, and thus growth in shade, may differ by leaf habit and vary with ontogeny following seed germination. To examine early responses of seedlings to shade in relation to morphological, physiological and biomass allocation traits, we compared seedlings of 10 temperate species, varying in their leaf habit (broadleaved versus needle-leaved) and observed tolerance to shade, when growing in two contrasting light treatments - open (about 20% of full sunlight) and shade (about 5% of full sunlight). We analyzed biomass allocation and its response to shade using allometric relationships. We also measured leaf gas exchange rates and leaf N in the two light treatments. Compared to the open treatment, shading significantly increased traits typically associated with high relative growth rate (RGR) - leaf area ratio (LAR), specific leaf area (SLA), and allocation of biomass into leaves, and reduced seedling mass and allocation to roots, and net assimilation rate (NAR). Interestingly, RGR was not affected by light treatment, likely because of morphological and physiological adjustments in shaded plants that offset reductions of in situ net assimilation of carbon in shade. Leaf area-based rates of light-saturated leaf gas exchange differed among species groups, but not between light treatments, as leaf N concentration increased in concert with increased SLA in shade. We found little evidence to support the hypothesis of a increased plasticity of broadleaved species compared to needle-leaved conifers in response to shade. However, an expectation of higher plasticity in shade-intolerant species than in shade-tolerant ones, and in leaf and plant morphology than in biomass allocation was supported across species of contrasting leaf habit. © 2016 German Botanical Society and The Royal Botanical Society of the Netherlands.

Uniform versus Asymmetric Shading Mediates Crown Recession in Conifers

PubMed Central

Schoonmaker, Amanda L.; Lieffers, Victor J.; Landhäusser, Simon M.

2014-01-01

In this study we explore the impact of asymmetrical vs. uniform crown shading on the mortality and growth of upper and lower branches within tree crowns, for two conifer species: shade intolerant lodgepole pine (Pinus contorta) and shade tolerant white spruce (Picea glauca). We also explore xylem hydraulics, foliar nutrition, and carbohydrate status as drivers for growth and expansion of the lower and upper branches in various types of shading. This study was conducted over a two-year period across 10 regenerating forest sites dominated by lodgepole pine and white spruce, in the lower foothills of Alberta, Canada. Trees were assigned to one of four shading treatments: (1), complete uniform shading of the entire tree, (2) light asymmetric shading where the lower 1/4–1/3 of the tree crown was shaded, (3) heavy asymmetric shading as in (2) except with greater light reduction and (4) control in which no artificial shading occurred and most of the entire crown was exposed to full light. Asymmetrical shading of only the lower crown had a larger negative impact on the bud expansion and growth than did uniform shading, and the effect was stronger in pine relative to spruce. In addition, lower branches in pine also had lower carbon reserves, and reduced xylem-area specific conductivity compared to spruce. For both species, but particularly the pine, the needles of lower branches tended to store less C than upper branches in the asymmetric shade, which could suggest a movement of reserves away from the lower branches. The implications of these findings correspond with the inherent shade tolerance and self-pruning behavior of these conifers and supports a carbon based mechanism for branch mortality – mediated by an asymmetry in light exposure of the crown. PMID:25136823

Uniform versus asymmetric shading mediates crown recession in conifers.

PubMed

Schoonmaker, Amanda L; Lieffers, Victor J; Landhäusser, Simon M

2014-01-01

In this study we explore the impact of asymmetrical vs. uniform crown shading on the mortality and growth of upper and lower branches within tree crowns, for two conifer species: shade intolerant lodgepole pine (Pinus contorta) and shade tolerant white spruce (Picea glauca). We also explore xylem hydraulics, foliar nutrition, and carbohydrate status as drivers for growth and expansion of the lower and upper branches in various types of shading. This study was conducted over a two-year period across 10 regenerating forest sites dominated by lodgepole pine and white spruce, in the lower foothills of Alberta, Canada. Trees were assigned to one of four shading treatments: (1), complete uniform shading of the entire tree, (2) light asymmetric shading where the lower 1/4-1/3 of the tree crown was shaded, (3) heavy asymmetric shading as in (2) except with greater light reduction and (4) control in which no artificial shading occurred and most of the entire crown was exposed to full light. Asymmetrical shading of only the lower crown had a larger negative impact on the bud expansion and growth than did uniform shading, and the effect was stronger in pine relative to spruce. In addition, lower branches in pine also had lower carbon reserves, and reduced xylem-area specific conductivity compared to spruce. For both species, but particularly the pine, the needles of lower branches tended to store less C than upper branches in the asymmetric shade, which could suggest a movement of reserves away from the lower branches. The implications of these findings correspond with the inherent shade tolerance and self-pruning behavior of these conifers and supports a carbon based mechanism for branch mortality--mediated by an asymmetry in light exposure of the crown.

Local auxin production underlies a spatially restricted neighbor-detection response in Arabidopsis

PubMed Central

Michaud, Olivier

2017-01-01

Competition for light triggers numerous developmental adaptations known as the “shade-avoidance syndrome” (SAS). Important molecular events underlying specific SAS responses have been identified. However, in natural environments light is often heterogeneous, and it is currently unknown how shading affecting part of a plant leads to local responses. To study this question, we analyzed upwards leaf movement (hyponasty), a rapid adaptation to neighbor proximity, in Arabidopsis. We show that manipulation of the light environment at the leaf tip triggers a hyponastic response that is restricted to the treated leaf. This response is mediated by auxin synthesized in the blade and transported to the petiole. Our results suggest that a strong auxin response in the vasculature of the treated leaf and auxin signaling in the epidermis mediate leaf elevation. Moreover, the analysis of an auxin-signaling mutant reveals signaling bifurcation in the control of petiole elongation versus hyponasty. Our work identifies a mechanism for a local shade response that may pertain to other plant adaptations to heterogeneous environments. PMID:28652343

Masking ability of bi- and tri- laminate all-ceramic veneers on tooth-colored ceramic discs.

PubMed

Farhan, Daniel; Sukumar, Smitha; von Stein-Lausnitz, Axel; Aarabi, Ghazal; Alawneh, Ahmad; Reissmann, Daniel R

2014-01-01

A predictable esthetic outcome is imperative when placing ceramic veneers. Discolored teeth pose a major challenge as sufficient material thickness is required to achieve a good esthetic result. There is limited evidence in the literature that compares the masking ability of multi-laminate veneers. The aim of this in-vitro study was to compare the masking ability of bi-laminate (BL) and tri-laminate (TL) all-ceramic veneers cemented on tooth-colored ceramic discs. A total of 40 veneers (shade A1, 10-mm diameter, 0.8-mm thick) were manufactured-20 BL veneers (0.4-mm pressable ceramic coping veneered with 0.4-mm thick enamel layer) and 20 TL veneers (0.4-mm coping veneered with 0.2-mm thick opaque interlayer and 0.2-mm thick enamel layer). A bonding apparatus was utilized to adhesively cement all veneers on the ceramic discs (shade A1), simulating teeth of light and dark color. The resulting groups (N = 10 each) were the reference groups (shade A1 ceramic base) BL-1 and TL-1 veneers, and the test groups (shade A4 ceramic base) BL-4 and TL-4 veneers. The color of the cemented veneers was measured using a spectrophotometer. The data were converted to CIE L*a*b* coordinates, and ΔE* were calculated to allow for statistical analysis. The color differences between the samples with the A1 and A4 ceramic bases were significantly lower when covered with TL veneers (mean ΔE*: 3.2 units) than with BL veneers (mean ΔE*: 4.0 units: p < 0.001), indicating a better masking ability of the TL veneers. The 0.8-mm thick TL veneer was able to mask darker tooth-colored ceramic disc within clinically acceptable limits. Increased understanding of the masking ability of ceramics and of color science is necessary in these esthetically aware times. Providing tri-laminate veneers for darker colored teeth seems to result in more predictable esthetical results than when using bi-laminate veneers. Patients with discolored/darker teeth may benefit from a more predictable esthetic result when teeth restored with tri-laminate rather than bi-laminate veneers. © 2014 Wiley Periodicals, Inc.

SRTM Colored Height and Shaded Relief: Sredinnyy Khrebet, Kamchatka Peninsula, Russia

NASA Technical Reports Server (NTRS)

2001-01-01

The Kamchatka Peninsula in eastern Russia is shown in this scene created from a preliminary elevation model derived from the first data collected during the Shuttle Radar Topography Mission (SRTM) on February 12, 2000. Sredinnyy Khrebet, the mountain range that makes up the spine of the peninsula, is a chain of active volcanic peaks. Pleistocene and recent glaciers have carved the broad valleys and jagged ridges that are common here. The relative youth of the volcanism is revealed by the topography as infilling and smoothing of the otherwise rugged terrain by lava, ash, and pyroclastic flows, particularly surrounding the high peaks in the south central part of the image. Elevations here range from near sea level up to 2,618 meters (8,590 feet).

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to white at the highest elevations.

Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard Space Shuttle Endeavour, launched on February 11,2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on Space Shuttle Endeavour in 1994. SRTM was designed to collect three-dimensional measurements of Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Size: 93.0 x 105.7 kilometers ( 57.7 x 65.6 miles) Location: 58.3 deg. North lat., 160.9 deg. East lon. Orientation: North toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 12, 2000

Ambae Island, Vanuatu (South Pacific)

NASA Technical Reports Server (NTRS)

2005-01-01

The recently active volcano Mt. Manaro is the dominant feature in this shaded relief image of Ambae Island, part of the Vanuatu archipelago located 1400 miles northeast of Sydney, Australia. About 5000 inhabitants, half the island's population, were evacuated in early December from the path of a possible lahar, or mud flow, when the volcano started spewing clouds of steam and toxic gases 10,000 feet into the atmosphere.

Last active in 1996, the 1496 meter (4908 ft.) high Hawaiian-style basaltic shield volcano features two lakes within its summit caldera, or crater. The ash and gas plume is actually emerging from a vent at the center of Lake Voui (at left), which was formed approximately 425 years ago after an explosive eruption.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise,Washington, D.C.

Location: 15.4 degree south latitude, 167.9 degrees east longitude Orientation: North toward the top, Mercator projection Size: 36.8 by 27.8 kilometers (22.9 by 17.3 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Ireland, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2005-01-01

The island of Ireland comprises a large central lowland of limestone with a relief of hills surrounded by a discontinuous border of coastal mountains which vary greatly in geological structure. The mountain ridges of the south are composed of old red sandstone separated by limestone river valleys. Granite predominates in the mountains of Galway, Mayo and Donegal in the west and north-west and in Counties Down and Wicklow on the east coast, while a basalt plateau covers much of the north-east of the country. The central plain, which is broken in places by low hills, is extensively covered with glacial deposits of clay and sand. It has considerable areas of bog and numerous lakes. The island has seen at least two general glaciations and everywhere ice-smoothed rock, mountain lakes, glacial valleys and deposits of glacial sand, gravel and clay mark the passage of the ice.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Location: 53.5 degrees North latitude, 8 degrees West longitude Orientation: North toward the top, Mercator projection Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

TRUE MASSES OF RADIAL-VELOCITY EXOPLANETS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Robert A., E-mail: rbrown@stsci.edu

We study the task of estimating the true masses of known radial-velocity (RV) exoplanets by means of direct astrometry on coronagraphic images to measure the apparent separation between exoplanet and host star. Initially, we assume perfect knowledge of the RV orbital parameters and that all errors are due to photon statistics. We construct design reference missions for four missions currently under study at NASA: EXO-S and WFIRST-S, with external star shades for starlight suppression, EXO-C and WFIRST-C, with internal coronagraphs. These DRMs reveal extreme scheduling constraints due to the combination of solar and anti-solar pointing restrictions, photometric and obscurational completeness,more » image blurring due to orbital motion, and the “nodal effect,” which is the independence of apparent separation and inclination when the planet crosses the plane of the sky through the host star. Next, we address the issue of nonzero uncertainties in RV orbital parameters by investigating their impact on the observations of 21 single-planet systems. Except for two—GJ 676 A b and 16 Cyg B b, which are observable only by the star-shade missions—we find that current uncertainties in orbital parameters generally prevent accurate, unbiased estimation of true planetary mass. For the coronagraphs, WFIRST-C and EXO-C, the most likely number of good estimators of true mass is currently zero. For the star shades, EXO-S and WFIRST-S, the most likely numbers of good estimators are three and four, respectively, including GJ 676 A b and 16 Cyg B b. We expect that uncertain orbital elements currently undermine all potential programs of direct imaging and spectroscopy of RV exoplanets.« less

Responses of legumes and grasses to non-, moderate, and dense shade in Missouri, USA. I. Forage yield and its species-level plasticity

Treesearch

Kejia Pang; J.W. Van Sambeek; Nadia E. Navarrete-Tindall; Chung-Ho Lin; Shibu Jose; H. E. Garrett

2017-01-01

Annual screenings of forage grasses and legumes for shade tolerance were conducted from 1996 to 2001 in the outdoor Shade Tolerance Screening Laboratory at the Horticulture and Agroforestry Research Center, University of Missouri. Forty-three forages were grown under non-shade (100% of full sunlight), moderate shade (45%), and dense shade (20%) without competition for...

Consistency in color parameters of a commonly used shade guide.

PubMed

Tashkandi, Esam

2010-01-01

The use of shade guides to assess the color of natural teeth subjectively remains one of the most common means for dental shade assessment. Any variation in the color parameters of the different shade guides may lead to significant clinical implications. Particularly, since the communication between the clinic and the dental laboratory is based on using the shade guide designation. The purpose of this study was to investigate the consistency of the L∗a∗b∗ color parameters of a sample of a commonly used shade guide. The color parameters of a total of 100 VITAPAN Classical Vacuum shade guide (VITA Zahnfabrik, Bad Säckingen, Germany(were measured using a X-Rite ColorEye 7000A Spectrophotometer (Grand Rapids, Michigan, USA). Each shade guide consists of 16 tabs with different designations. Each shade tab was measured five times and the average values were calculated. The ΔE between the average L∗a∗b∗ value for each shade tab and the average of the 100 shade tabs of the same designation was calculated. Using the Student t-test analysis, no significant differences were found among the measured sample. There is a high consistency level in terms of color parameters of the measured VITAPAN Classical Vacuum shade guide sample tested.

A scaleable methodology for assessing the impacts of urban shade on the summer electricity use of residential homes

NASA Astrophysics Data System (ADS)

Taylor, Robert Vanderlei

Our cities are experiencing unprecedented growth while net global temperatures continue to trend warmer making sustainable urban development and energy conservation pressing public issues. This research explores how urban landscaping -- in particular trees and buildings -- affect summer electricity use in residential homes. I studied the interactions of urban shade and temperature to explore how vegetation distribution and intensity could play a meaningful role in heat mitigation in urban environments. Only a few studies have reconciled modeled electricity savings from tree shade with actual electricity consumption data. This research proposes a methodology for modeling the isolated effects of urban shade (tree shade vs building shade) on buildings' summertime electricity consumption from micro to mesoscales, empirically validating the modeled shade with actual electricity billing data, and comparing the electric energetic impact of tree shade effects with building shade effects. This proposed methodology seeks to resolve three primary research questions: 1) What are the modeled quantities of urban shade associated with the area of interest (AOI)? 2) To what extent do the effects of shading from trees and buildings mitigate summertime heat in the AOI? 2) To what extent do the shade effects from trees and buildings reduce summertime electricity consumption in the AOI?

Autofluorescence study and selected cyanidin quantification in the Jewel orchids Anoectochilus sp. and Ludisia discolor

PubMed Central

Poobathy, Ranjetta; Zakaria, Rahmad; Murugaiyah, Vikneswaran

2018-01-01

Anoectochilus sp. and Ludisia discolor are known as Jewel orchids. Both species are terrestrial wild orchids that grow in shaded areas of forests. The Jewel orchids are renowned for the beauty of their leaves, which are dark-green laced with silvery or golden veins. The orchids are used as a cure in various parts of Asia. Overharvesting and anthropogenic disturbances threaten the existence of the Jewel orchids in the wild, necessitating human intervention in their survival. An understanding of the structure and adaptations of a plant may assist in its survival when propagated outside of its habitat. In this study, ex vitro leaves of Anoectochilus sp. and L. discolor were subjected to freehand sectioning, and then inspected through brightfield and fluorescence microscopy. The study indicated that all parts of both plants presented typical monocotyledonous characteristics except the leaves. The leaves displayed dorsiventrality with distinct palisade and spongy mesophyll layers. The spongy mesophyll layer contained cells which fluoresced a bright red when exposed to ultraviolet, blue, and green light wavelengths, hinting at the presence of anthocyanins for photoprotection. Cyanidin was detected in the leaves of L. discolor, as enumerated through high performance liquid chromatography (HPLC). The observations indicated that Anoectochilus sp. and L. discolor are well-adapted to live under shaded conditions with minimal exposure to light. PMID:29649288

A software package to improve image quality and isolation of objects of interest for quantitative stereology studies of rat hepatocarcinogenesis.

PubMed

Xu, Yihua; Pitot, Henry C

2006-03-01

In the studies of quantitative stereology of rat hepatocarcinogenesis, we have used image analysis technology (automatic particle analysis) to obtain data such as liver tissue area, size and location of altered hepatic focal lesions (AHF), and nuclei counts. These data are then used for three-dimensional estimation of AHF occurrence and nuclear labeling index analysis. These are important parameters for quantitative studies of carcinogenesis, for screening and classifying carcinogens, and for risk estimation. To take such measurements, structures or cells of interest should be separated from the other components based on the difference of color and density. Common background problems seen on the captured sample image such as uneven light illumination or color shading can cause severe problems in the measurement. Two application programs (BK_Correction and Pixel_Separator) have been developed to solve these problems. With BK_Correction, common background problems such as incorrect color temperature setting, color shading, and uneven light illumination background, can be corrected. With Pixel_Separator different types of objects can be separated from each other in relation to their color, such as seen with different colors in immunohistochemically stained slides. The resultant images of such objects separated from other components are then ready for particle analysis. Objects that have the same darkness but different colors can be accurately differentiated in a grayscale image analysis system after application of these programs.

Space Radar Image of Belgrade, Serbia

NASA Technical Reports Server (NTRS)

1994-01-01

This spaceborne radar image of Belgrade, Serbia, illustrates the variety of land use patterns that can be observed with a multiple wavelength radar system. Belgrade, the capital of Serbia and former capital of Yugoslavia, is the bright area in the center of the image. The Danube River flows from the top to the bottom of the image, and the Sava River flows into the Danube from the left. Agricultural fields appear in shades of dark blue, purple and brown in outlying areas. Vegetated areas along the rivers appear in light blue-green, while dense forests in hillier areas in the lower left appear in a darker shade of green. The image was acquired by the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) onboard the space shuttle Endeavour on October 2, 1994. The image is centered at 44.5 degrees north latitude and 20.5 degrees east longitude. North is toward the upper right. The image shows an area 36 kilometers by 32 kilometers 22 miles by 20 miles). The colors are assigned to different frequencies and polarizations of the radar as follows: red is L-band, horizontally transmitted, horizontally received; green is L-band, horizontally transmitted, vertically received; blue is C-band, horizontally transmitted, vertically received. SIR-C/X-SAR, a joint mission of the German, Italian and United States space agencies, is part of NASA's Mission to Planet Earth program.

Heat stress in cows at pasture and benefit of shade in a temperate climate region.

PubMed

Veissier, Isabelle; Van Laer, Eva; Palme, Rupert; Moons, Christel P H; Ampe, Bart; Sonck, Bart; Andanson, Stéphane; Tuyttens, Frank A M

2018-04-01

Under temperate climates, cattle are often at pasture in summer and are not necessarily provided with shade. We aimed at evaluating in a temperate region (Belgium) to what extent cattle may suffer from heat stress (measured through body temperature, respiration rate and panting score, cortisol or its metabolites in milk, and feces on hot days) and at assessing the potential benefits of shade. During the summer of 2012, 20 cows were kept on pasture without access to shade. During the summer of 2011, ten cows had access to shade (young trees with shade cloth hung between them), whereas ten cows had no access. Climatic conditions were quantified by the Heat Load Index (HLI). In animals without access to shade respiration rates, panting scores, rectal temperatures, and milk cortisol concentrations increased as HLI increased in both 2011 and 2012. Fecal cortisol metabolites varied with HLI in 2011 only. When cattle had access to shade, their use of shade increased as the HLI increased. This effect was more pronounced during the last part of the summer, possibly due to better acquaintance with the shade construction. In this case, shade use increased to 65% at the highest HLI (79). Shade tempered the effects on respiration, rectal temperature, and fecal cortisol metabolites. Milk cortisol was not influenced by HLI for cows using shade for > 10% of the day. Therefore, even in temperate areas, cattle may suffer from heat when they are at pasture in summer and providing shade can reduce such stress.

Assessment of microclimate conditions under artificial shades in a ginseng field.

PubMed

Lee, Kyu Jong; Lee, Byun-Woo; Kang, Je Yong; Lee, Dong Yun; Jang, Soo Won; Kim, Kwang Soo

2016-01-01

Knowledge on microclimate conditions under artificial shades in a ginseng field would facilitate climate-aware management of ginseng production. Weather data were measured under the shade and outside the shade at two fields located in Gochang-gun and Jeongeup-si, Korea, in 2011 and 2012 seasons to assess temperature and humidity conditions under the shade. An empirical approach was developed and validated for the estimation of leaf wetness duration (LWD) using weather measurements outside the shade as inputs to the model. Air temperature and relative humidity were similar between under the shade and outside the shade. For example, temperature conditions favorable for ginseng growth, e.g., between 8°C and 27°C, occurred slightly less frequently in hours during night times under the shade (91%) than outside (92%). Humidity conditions favorable for development of a foliar disease, e.g., relative humidity > 70%, occurred slightly more frequently under the shade (84%) than outside (82%). Effectiveness of correction schemes to an empirical LWD model differed by rainfall conditions for the estimation of LWD under the shade using weather measurements outside the shade as inputs to the model. During dew eligible days, a correction scheme to an empirical LWD model was slightly effective (10%) in reducing estimation errors under the shade. However, another correction approach during rainfall eligible days reduced errors of LWD estimation by 17%. Weather measurements outside the shade and LWD estimates derived from these measurements would be useful as inputs for decision support systems to predict ginseng growth and disease development.

Assessment of microclimate conditions under artificial shades in a ginseng field

PubMed Central

Lee, Kyu Jong; Lee, Byun-Woo; Kang, Je Yong; Lee, Dong Yun; Jang, Soo Won; Kim, Kwang Soo

2015-01-01

Background Knowledge on microclimate conditions under artificial shades in a ginseng field would facilitate climate-aware management of ginseng production. Methods Weather data were measured under the shade and outside the shade at two fields located in Gochang-gun and Jeongeup-si, Korea, in 2011 and 2012 seasons to assess temperature and humidity conditions under the shade. An empirical approach was developed and validated for the estimation of leaf wetness duration (LWD) using weather measurements outside the shade as inputs to the model. Results Air temperature and relative humidity were similar between under the shade and outside the shade. For example, temperature conditions favorable for ginseng growth, e.g., between 8°C and 27°C, occurred slightly less frequently in hours during night times under the shade (91%) than outside (92%). Humidity conditions favorable for development of a foliar disease, e.g., relative humidity > 70%, occurred slightly more frequently under the shade (84%) than outside (82%). Effectiveness of correction schemes to an empirical LWD model differed by rainfall conditions for the estimation of LWD under the shade using weather measurements outside the shade as inputs to the model. During dew eligible days, a correction scheme to an empirical LWD model was slightly effective (10%) in reducing estimation errors under the shade. However, another correction approach during rainfall eligible days reduced errors of LWD estimation by 17%. Conclusion Weather measurements outside the shade and LWD estimates derived from these measurements would be useful as inputs for decision support systems to predict ginseng growth and disease development. PMID:26843827

Organic-inorganic hybrid inverted photodiode with planar heterojunction for achieving low dark current and high detectivity

NASA Astrophysics Data System (ADS)

Ha, JaeUn; Yoon, Seongwon; Lee, Jong-Soo; Chung, Dae Sung

2016-03-01

In this study, the strategy of using an organic-inorganic hybrid planar heterojunction consisting of polymeric semiconductors and inorganic nanocrystals is introduced to realize a high-performance hybrid photodiode (HPD) with low dark current and high detectivity. To prevent undesired charge injection under the reverse bias condition, which is the major dark current source of the photodiode, a well-defined planar heterojunction is strategically constructed via smart solution process techniques. The optimized HPD renders a low dark current of ˜10-5 mA cm-2 at -5 V and ˜10-6 mA cm-2 at -1 V, as well as a high detectivity ˜1012 Jones across the entire visible wavelength range. Furthermore, excellent photocurrent stability is demonstrated under continuous light exposure. We believe that the solution-processed planar heterojunction with inverted structure can be an attractive alternative diode structure for fabricating high-performance HPDs, which usually suffer from high dark current issues.

Dark Current Characterization of SW HgCdTe IRFPAs Detectors on Si Substrate with Long Time Integration

NASA Astrophysics Data System (ADS)

Song, P. Y.; Ye, Z. H.; Huang, A. B.; Chen, H. L.; Hu, X. N.; Ding, R. J.; He, L.

2016-09-01

The dark currents of two short wave (SW) HgCdTe infrared focal plane arrays (IRFPA) detectors hybridized with direct injection (DI) readout and capacitance transimpedance amplifier (CTIA) with long time integration were investigated. The cutoff wavelength of the two SW IRFPAs is about 2.6 μm at 84 K. The dark current densities of DI and CTIA samples are approximately 8.0 × 10-12 A/cm2 and 7.2 × 10-10 A/cm2 at 110 K, respectively. The large divergence of the dark current density might arise from the injection efficiency difference of the two readouts. The low injection efficiency of the DI readout, compared with the high injection efficiency of the CTIA readout at low temperature, makes the dark current density of the DI sample much lower than that of the CTIA sample. The experimental value of injection efficiency of the DI sample was evaluated as 1.1% which is consistent with its theoretical value.

Improving representation of riparian vegetation shading in a regional stream temperature model using LiDAR data.

PubMed

Loicq, Pierre; Moatar, Florentina; Jullian, Yann; Dugdale, Stephen J; Hannah, David M

2018-05-15

Modelling river temperature at the catchment scale is needed to understand how aquatic communities may adapt to current and projected climate change. In small and medium rivers, riparian vegetation can greatly reduce maximum water temperature by providing shade. It is thus important that river temperature models are able to correctly characterise the impact of this riparian shading. In this study, we describe the use of a spatially-explicit method using LiDAR-derived data for computing the riparian shading on direct and diffuse solar radiation. The resulting data are used in the T-NET one-dimensional stream temperature model to simulate water temperature from August 2007 to July 2014 for 270km of the Loir River, an indirect tributary of the Loire River (France). Validation is achieved with 4 temperature monitoring stations spread along the Loir River. The vegetation characterised with the LiDAR approach provides a cooling effect on maximum daily temperature (T max ) ranging from 3.0°C (upstream) to 1.3°C (downstream) in late August 2009. Compared to two other riparian shading routines that are less computationally-intensive, the use of our LiDAR-based methodology improves the bias of T max simulated by the T-NET model by 0.62°C on average between April and September. However, difference between the shading routines reaches up to 2°C (monthly average) at the upstream-most station. Standard deviation of errors on T max is not improved. Computing the impact of riparian vegetation at the hourly timescale using reach-averaged parameters provides results close to the LiDAR-based approach, as long as it is supplied with accurate vegetation cover data. Improving the quality of riparian vegetation data should therefore be a priority to increase the accuracy of stream temperature modelling at the regional scale. Copyright © 2017 Elsevier B.V. All rights reserved.

Polar Lunar Regions: Exploiting Natural and Augmented Thermal Environments

NASA Technical Reports Server (NTRS)

Ryan, Robert E.; McKellip, Rodney; Brannon, David P.; Underwood, Lauren; Russell, Kristen J.

2007-01-01

In polar regions of the Moon, some areas within craters are permanently shadowed from solar illumination and can reach temperatures of 100 K or less. These regions could serve as cold traps, capturing ice and other volatile compounds. These potential ice stores have many applications for lunar exploration. Within double-shaded craters, even colder regions exist, with temperatures never exceeding 50 K in many cases. Observed temperatures suggest that these regions could enable equivalent liquid nitrogen cryogenic functions. These permanently shaded polar craters also offer unprecedented high-vacuum cryogenic environments, which in their current state could support cryogenic applications. Besides ice stores, the unique conditions at the lunar poles harbor an environment that provides an opportunity to reduce the power, weight, and total mass that needs to be carried from the Earth to the Moon for lunar exploration and research. Reducing the heat flux of geothermal, black body radiation can have significant impacts on the achievable temperature. With a few manmade augmentations, permanently shaded craters located near the lunar poles achieve temperatures even lower than those that naturally exist. Our analysis reveals that lightweight thermal shielding within shaded craters could create an environment several Kelvin above absolute zero. The temperature ranges of both naturally shaded and thermally augmented craters could enable the long-term storage of most gases, low-temperature superconductors for large magnetic fields, devices and advanced high-speed computing instruments. Augmenting thermal conditions in these craters could then be used as a basis for the development of an advanced thermal management architecture that would support a wide variety of cryogenically based applications. Lunar exploration and habitation capabilities would significantly benefit if permanently shaded craters, augmented with thermal shielding, were used to facilitate the operation of near absolute zero instruments, including a wide variety of cryogenically based propulsion, energy, communication, sensing, and computing devices. The required burden of carrying massive life-supporting components from the Earth to the Moon for lunar exploration and research potentially could be reduced.

Observation of dark pulses in 10 nm thick YBCO nanostrips presenting hysteretic current voltage characteristics

NASA Astrophysics Data System (ADS)

Ejrnaes, M.; Parlato, L.; Arpaia, R.; Bauch, T.; Lombardi, F.; Cristiano, R.; Tafuri, F.; Pepe, G. P.

2017-12-01

We have fabricated several 10 nm thick and 65 nm wide YBa2Cu3O7-δ (YBCO) nanostrips. The nanostrips with the highest critical current densities are characterized by hysteretic current voltage characteristics (IVCs) with a direct bistable switch from the zero-voltage to the finite voltage state. The presence of hysteretic IVCs allowed the observation of dark pulses due to fluctuations phenomena. The key role of the bistable behavior is its ability to transform a small disturbance (e.g. an intrinsic fluctuation) into a measurable transient signal, i.e. a dark pulse. On the contrary, in devices characterized by lower critical current density values, the IVCs are non-hysteretic and dark pulses have not been observed. To investigate the physical origin of the dark pulses, we have measured the bias current dependence of the dark pulse rate: the observed exponential increase with the bias current is compatible with mechanisms based on thermal activation of magnetic vortices in the nanostrip. We believe that the successful amplification of small fluctuation events into measurable signals in nanostrips of ultrathin YBCO is a milestone for further investigation of YBCO nanostrips for superconducting nanostrip single photon detectors and other quantum detectors for operation at higher temperatures.

Spectral response, dark current, and noise analyses in resonant tunneling quantum dot infrared photodetectors.

PubMed

Jahromi, Hamed Dehdashti; Mahmoodi, Ali; Sheikhi, Mohammad Hossein; Zarifkar, Abbas

2016-10-20

Reduction of dark current at high-temperature operation is a great challenge in conventional quantum dot infrared photodetectors, as the rate of thermal excitations resulting in the dark current increases exponentially with temperature. A resonant tunneling barrier is the best candidate for suppression of dark current, enhancement in signal-to-noise ratio, and selective extraction of different wavelength response. In this paper, we use a physical model developed by the authors recently to design a proper resonant tunneling barrier for quantum infrared photodetectors and to study and analyze the spectral response of these devices. The calculated transmission coefficient of electrons by this model and its dependency on bias voltage are in agreement with experimental results. Furthermore, based on the calculated transmission coefficient, the dark current of a quantum dot infrared photodetector with a resonant tunneling barrier is calculated and compared with the experimental data. The validity of our model is proven through this comparison. Theoretical dark current by our model shows better agreement with the experimental data and is more accurate than the previously developed model. Moreover, noise in the device is calculated. Finally, the effect of different parameters, such as temperature, size of quantum dots, and bias voltage, on the performance of the device is simulated and studied.

Phototropin and light-signaling in phototropism.

PubMed

Kimura, Mitsuhiro; Kagawa, Takatoshi

2006-10-01

Blue-light-induced phototropism in higher plants is regulated by phototropin, which is a photoreceptor kinase that contains a flavin mononucleotide (FMN). Recently, it was found that this kinase is inhibited by the binding of the LOV2 (light-oxygen-voltage2) domain in the dark but that its activity is increased in the light by the release of the LOV2 domain. Phototropin-associated proteins have been identified, although the proteins that are phosphorylated by phototropin are still unknown. The asymmetrical auxin distribution caused by unilateral irradiation suggests that differential growth is induced by a difference in auxin-regulated gene expression between the shaded and illuminated sides of plant organs. Transcription-related factors, such as NPH4/ARF7, MSG2/IAA19 and SCF(TIR1), play key roles in this process.

ARC-1979-AC79-7081

NASA Image and Video Library

1979-07-08

P-21747 C Range: 2,200,000 miles This image shows a region of the Jovian atmosphere from approximately 25° N to the equatorial region. The north temperate jet, at approximately 23° N, where the wind speed is about 150 meters per second, is seen as a dark brown line from the left-hand edge to the right-hand corner of the picture. The wispy clouds of the north equatorial belt appear as shades of brown. The lower right-hand corner of the image shows the brighter (white) clouds of the equatorial region. A small blue area is apparent near the lower edge, which corresponds to a region free of the upper clouds, where it is possible to penetrate to cloud layers approximately 60 kilometers below the visible surface.

ARC-1979-A79-7081

NASA Image and Video Library

1979-07-08

P-21747 BW Range: 2,200,000 miles This image shows a region of the Jovian atmosphere from approximately 25° N to the equatorial region. The north temperate jet, at approximately 23° N, where the wind speed is about 150 meters per second, is seen as a dark brown line from the left-hand edge to the right-hand corner of the picture. The wispy clouds of the north equatorial belt appear as shades of brown. The lower right-hand corner of the image shows the brighter (white) clouds of the equatorial region. A small blue area is apparent near the lower edge, which corresponds to a region free of the upper clouds, where it is possible to penetrate to cloud layers approximately 60 kilometers below the visible surface.

Prospects of direct search for dark photon and dark Higgs in SeaQuest/E1067 experiment at the Fermilab main injector

NASA Astrophysics Data System (ADS)

Liu, Ming Xiong

2017-03-01

In this review, we present the current status and prospects of the dark sector physics search program of the SeaQuest/E1067 fixed target dimuon experiment at Fermilab Main Injector. There has been tremendous excitement and progress in searching for new physics in the dark sector in recent years. Dark sector refers to a collection of currently unknown particles that do not directly couple with the Standard Model (SM) strong and electroweak (EW) interactions but assumed to carry gravitational force, thus could be candidates of the missing Dark Matter (DM). Such particles may interact with the SM particles through “portal” interactions. Two of the simple possibilities are being investigated in our initial search: (1) dark photon and (2) dark Higgs. They could be within immediate reach of current or near future experimental search. We show there is a unique opportunity today at Fermilab to directly search for these particles in a highly motivated but uncharted parameter space in high-energy proton-nucleus collisions in the beam-dump mode using the 120 GeV proton beam from the Main Injector. Our current search window covers the mass range 0.2-10 GeV/c2, and in the near future, by adding an electromagnetic calorimeter (EMCal) to the spectrometer, we can further explore the lower mass region down to about ˜1 MeV/c2 through the di-electron channel. If dark photons (and/or dark Higgs) were observed, they would revolutionize our understanding of the fundamental structures and interactions of our universe.

Responses of legumes and grasses to non-, moderate, and dense shade in Missouri, USA. II. Forage quality and its species-level plasticity

Treesearch

Kejia Pang; J.W. Van Sambeek; Nadia E. Navarrete-Tindall; Chung-Ho Lin; Shibu Jose; H. E. Garrett

2017-01-01

From a series of shade tolerance screening trials conducted in an outdoor Shade Tolerance Screening Laboratory, 22 forages (16 grasses and 6 legumes) were selected for quality evaluation. The forages were grown under non-shade (100% of full sun, the control), moderate shade (45%), and dense shade (20%) with adequate water and nutrients and free of competition from...

Shade-induced nuclear localization of PIF7 is regulated by phosphorylation and 14-3-3 proteins in Arabidopsis.

PubMed

Huang, Xu; Zhang, Qian; Jiang, Yupei; Yang, Chuanwei; Wang, Qianyue; Li, Lin

2018-06-21

Shade avoidance syndrome enables shaded plants to grow and compete effectively against their neighbors. In Arabidopsis , the shade-induced de-phosphorylation of the transcription factor PIF7 (PHYTOCHROME-INTERACTING FACTOR 7) is the key event linking light perception to stem elongation. However, the mechanism through which phosphorylation regulates the activity of PIF7 is unclear. Here, we show that shade light induces the de-phosphorylation and nuclear accumulation of PIF7. Phosphorylation-resistant site mutations in PIF7 result in increased nuclear localization and shade-induced gene expression, and consequently augment hypocotyl elongation. PIF7 interacts with 14-3-3 proteins. Blocking the interaction between PIF7 and 14-3-3 proteins or reducing the expression of 14-3-3 proteins accelerates shade-induced nuclear localization and de-phosphorylation of PIF7, and enhances the shade phenotype. By contrast, the 14-3-3 overexpressing line displays an attenuated shade phenotype. These studies demonstrate a phosphorylation-dependent translocation of PIF7 when plants are in shade and a novel mechanism involving 14-3-3 proteins, mediated by the retention of PIF7 in the cytoplasm that suppresses the shade response. © 2018, Huang et al.

A Critical Evaluation of the Influence of the Dark Exchange Current on the Performance of Dye-Sensitized Solar Cells

PubMed Central

García-Rodríguez, Rodrigo; Villanueva-Cab, Julio; Anta, Juan A.; Oskam, Gerko

2016-01-01

The influence of the thickness of the nanostructured, mesoporous TiO2 film on several parameters determining the performance of a dye-sensitized solar cell is investigated both experimentally and theoretically. We pay special attention to the effect of the exchange current density in the dark, and we compare the values obtained by steady state measurements with values extracted from small perturbation techniques. We also evaluate the influence of exchange current density, the solar cell ideality factor, and the effective absorption coefficient of the cell on the optimal film thickness. The results show that the exchange current density in the dark is proportional to the TiO2 film thickness, however, the effective absorption coefficient is the parameter that ultimately defines the ideal thickness. We illustrate the importance of the exchange current density in the dark on the determination of the current–voltage characteristics and we show how an important improvement of the cell performance can be achieved by decreasing values of the total series resistance and the exchange current density in the dark. PMID:28787833

Effects of sunlight on behavior and 25-hydroxyvitamin D levels in two species of Old World fruit bats

PubMed Central

Southworth, Lizabeth O.; Holick, Michael F.; Chen, Tai C.; Kunz, Thomas H.

2013-01-01

It has long been accepted that most vertebrate animals meet their vitamin D requirements from exposure of skin to UV-B (UV-B) radiation. Many factors affect this endogenous synthesis of vitamin D, including season, latitude, time of day, age, presence of hair, and degree of skin pigmentation. Most bats roost in dark places by day and forage at night, and thus have little or no potential for sunlight exposure. Notwithstanding, some tropical species are diurnal and are known to roost in the canopy of trees where they may be exposed to sunlight for up to 12 h each day. In this study, two species of captive tropical bats (both species are active at night but one, Rousettus aegyptiacus, roosts in caves, tombs, and buildings, whereas the other, Pteropus hypomelanus, roosts in trees) were evaluated for their ability to endogenously synthesize vitamin D. Following timed periods of sunlight exposure, blood plasma was analyzed using a competitive protein binding assay (CPBA) to determine concentrations of 25-hydroxyvitamin D [25(OH)D], the major circulating vitamin D metabolite. The ability to photoconvert provitamin D (7-dehydrocholesterol, 7-DHC) in the sub-tropical winter was determined using sunlight exposed borosilicate samples of 7-DHC in hourly increments. Finally, both species were evaluated in their preference for a roost site by the release of individuals into sunlight or shade in timed trials. Our results support the hypotheses: (1) when exposed to natural sunlight, both species exhibited an ability to endogenously synthesize vitamin D, although significant differences were found between the two, (2) photoconversion of 7-DHC to previtamin D3 is possible during the mid-day hours of a sub-tropical winter day and (3) captive, cave roosting R. aegyptiacus will choose shaded roost sites while captive P. hypomelanus will show no preference for either shade or sun. PMID:24494054

Comparative life history and physiology of two understory Neotropical herbs.

PubMed

Mulkey, Stephen S; Smith, Alan P; Wright, S Joseph

1991-10-01

Demography and physiology of two broad-leaved understory tropical herbs (Marantaceae) were studied in gaps and shaded understory in large-scale irrigated and control treatments during the dry season at Barro Colorado Island (BCI), Panama. Because photosynthetic acclimation potential may not predict light environments where tropical species are found, we studied a suite of physiological features to determine if they uniquely reflect the distribution of each species. Calathea inocephala and Pleiostachya pruinosa grow and reproduce in gaps, persist in shade, and have equivalent rates of leaf production. Calathea leaves survived 2 to 3 times as long as leaves of Pleiostachya and plants of Pleiostachya were 6 to 8 times more likely to die as plants of Calathea during 3.5 years of study. Pleiostachya had lowest survival in shade and when not irrigated during the dry season, while Calathea survived well in both habitats and both treatments. Pleiostachya had higher photosynthetic capacity and stomatal conductance than Calathea and acclimated to gaps by producing leaves with higher photosynthetic capacity. Calathea had lower mesophyll CO 2 concentrations than Pleiostachya. Both species had similar dark respiration rates and light compensation points, and water-use and nitrogen-use efficiencies were inversely related between species. Species showed no differences in leaf osmotic potentials at full turgor. Calathea roots were deeper and had tuberous swellings.Leaf-level assimilation and potential water loss are consistent with where these species are found, but photosynthetic acclimation to high light does not reflect both species' abilities to grow and reproduce in gaps. Pleiostachya's gap-dependent, rapid growth and reproduction require high rates of carbon gain in short-lived leaves, which can amortize their cost quickly. High rates of water loss are associated with reduced longevity during drought. Calathea's roots may confer greater capacitance, while its leaves are durable, long-lived and have lower water loss, permitting persistence long after gap closure.

Southern Florida, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

The very low topography of southern Florida is evident in this color-coded shaded relief map generated with data from the Shuttle Radar Topography Mission. The image on the left is a standard view, with the green colors indicating low elevations, rising through yellow and tan, to white at the highest elevations. In this exaggerated view even those highest elevations are only about 60 meters (197 feet) above sea level.

For the view on the right, elevations below 5 meters (16 feet) above sea level have been colored dark blue, and lighter blue indicates elevations below 10 meters (33 feet). This is a dramatic demonstration of how Florida's low topography, especially along the coastline, make it especially vulnerable to flooding associated with storm surges. Planners can use data like these to predict which areas are in the most danger and help develop mitigation plans in the event of particular flood events.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Science Mission Directorate, Washington, D.C.

Location: 27 degrees north latitude, 81 degrees west longitude Orientation: North toward the top, Mercator projection Size: 397 by 445 kilometers (246 by 276 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Resin cement color stability and its influence on the final shade of all-ceramics.

PubMed

Kilinc, Evren; Antonson, Sibel A; Hardigan, Patrick C; Kesercioglu, Atilla

2011-07-01

Adhesive resin cements may go through internal discoloration, which may show-through and affect the appearance of translucent all-ceramic restorations. This in vitro study evaluated the amount of resin cement color change and its effect on the final shade of the all-ceramics. Three different resin cements in both light and dual-cure forms were included in the study (Nexus-2/Kerr; Appeal/Ivoclar Vivadent; Calibra/Dentsply). All resin cements contained veneered (IPS Empress Esthetic, ETC1 shade, 20 mm × 1 mm ingot discs) and uncovered groups (n=10/group), all luted on white backgrounds (acetalpolyoxymethylene/Delrin(®)). Curing was performed according to ISO standards with a calibrated LED curing-light (Flashlite 1401). Samples were stored in 37°C distilled water at dark. Spectrophotometric baseline color measurements (Color Eye 7000A) were performed from the samples' top surfaces at 24h (D65 illuminator). Samples were subjected to 65 h of accelerated ageing (Atlas Ci4000). Further color measurements from the same areas were recorded in CIEL*a*b* coordinates where a ΔE data above 3 was accepted as visible discoloration (OptiviewLite-1.9software). Statistical analysis was performed using a nested random effects model and Tukey's post hoc analysis. Light-cure groups showed better color stability in all three resins but only in Appeal resin cement, the dual-cure group discolored significantly more (p<0.001). More discoloration was recorded on uncovered cement groups that represented the exposed cement at the margins. There was no visible color change (ΔE>3) through the ceramic surface on any veneered group. All resin cements showed varying degrees of discoloration after accelerated ageing however their actual color change was partially masked by the ceramic. Dual-cure resin cements may affect aesthetics on restoration margins if directly exposed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Rapid photosynthetic acclimation of Shorea johorensis seedlings after logging disturbance in Central Kalimantan.

PubMed

Clearwater, M J; Susilawaty, R; Effendi, R; van Gardingen, P R

1999-12-01

This study examined the photosynthetic acclimation of pre-existing Shorea johorensis (Dipterocarpaceae) seedlings to the change in conditions that occurs at the time of logging in Central Kalimantan, Indonesia. The hypothesis was that the seedlings would be unable to acclimate beyond partially open conditions after canopy disturbance caused by logging, therefore limiting the potential for regeneration in the most open areas. Bleaching and reductions in the predawn ratio of variable to maximum fluorescence (F v /F m ) indicated chronic photoinhibition and damage to the previously shade-adapted leaves of seedlings in an area logged 2 weeks earlier. The majority of seedlings in partially open and open environments of an area logged 3 months earlier were already growing fast. Leaves that had developed in the new environment showed only small reductions in predawn F v /F m and large increases in the light saturated rate of photosynthesis (A max ) per unit area when compared to shaded seedlings. Leaves in the most open environments had higher but more variable nitrogen concentrations, A max per unit area and A max per unit mass when compared to seedlings in partially open environments. Increases in dark respiration were disproportionately large compared to increases in A max , and may have been the result of increased investment in photoprotective mechanisms. The response of stomatal conductance to the vapour pressure deficit and leaf temperature was examined, but it suggested only a 10% reduction in daily leaf level carbon gain in open environments. The ratio of leaf area to fine root mass was highest in shade-suppressed and newly exposed seedlings, suggesting a potential hydraulic limitation to transpiration during acclimation. However, rainfall during this period was high and leaf water potentials did not differ between disturbed and undisturbed environments. S. johorensis seedlings were capable of significant acclimation to conditions more extreme than partial canopy opening. Low seedling density after logging during the wet season cannot be explained by a limited potential for photosynthetic acclimation.

Influence of light source, polarization, education, and training on shade matching quality.

PubMed

Clary, Jacqueline A; Ontiveros, Joe C; Cron, Stanley G; Paravina, Rade D

2016-07-01

Many factors influence the quality of shade selection, and isolating how significantly each of these factors influences results is difficult. The purpose of this in vitro study was to compare results of shade matching using handheld lights with or without a polarizing filter with results obtained using a professional viewing booth and to analyze the influence of education and training on shade selection outcome. A total of 96 third-year dental students (evaluators) were randomly separated into 4 groups. Each group was assigned 1 of 2 handheld shade-matching devices (lights) with or without a polarizing filter. Each group performed a shade matching exercise using the handheld light or a professional viewing booth. The exercise consisted of matching shade tabs placed in a typodont to a commercial shade guide. Each group repeated this procedure 4 times over a 9-week period. A lecture on shade matching was presented at the fifth week of the study, between "before" and "after" shade matching procedures. Shade matching scores with handheld lights (7.8) were higher than scores of shade matching with the viewing booth (7.2). The mean scores for before (7.2) and after (7.8) shade matching (with education and training in between) were significantly different. The combined effect of light and education and training improved the shade matching score by 1.2, from 6.8 in the before sessions using the viewing booth to 8.0 in the after sessions using handheld lights. A 21% increase in the number of evaluators who selected 1 of 4 best matches was recorded, 10% for handheld lights versus viewing booth after education and training versus before sessions and 11% between after sessions using handheld lights versus before sessions using viewing booth. Within the limits of the study, the shade matching scores with handheld lights were significantly better than the results obtained using a viewing booth (P<.01). Using a handheld light with or without a polarizing filter did not influence shade matching results. Mean shade matching scores were significantly better after education and training (P<.01). Light combined with education and training resulted in the greatest increase in shade matching quality. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Achieving the desired colour in discoloured teeth, using leucite-based CAD-CAM laminate systems.

PubMed

Turgut, Sedanur; Bagis, Bora; Ayaz, Elif Aydogan

2014-01-01

To evaluate the cumulative effect of the abutment tooth and resin cement colour on the resultant optical properties of porcelain laminate veneers (PLVs) fabricated with leucite-based CAD/CAM blocks with different shades and thicknesses. A total of 224 ceramic specimens were prepared from the IPS Empress CAD with four different shades of HT-A1, LT-A1, MT-A1 and Bl-1. Resin composite discs were prepared with shade A3.5. For the cementation, 4 different shades of light-cure resin cements were chosen. L*, a*, and b* values, as well as the chroma (C) and hue (h) values of each cemented ceramic and the A1 shade table, were recorded. L*, Cab* and hab* values of the cemented ceramics were influenced by ceramic shade, ceramic thickness, cement shade, and interaction terms of the three variables. There were significant differences between the 1-mm-thick ceramic veneers that exhibited higher L* and lower Cab* values compared with veneers that were 0.5mm in thickness. Using the Tr shade cement resulted in lower L* and higher Cab* values for all thicknesses and ceramic shades, whereas the WO shade cement resulted in higher values. The selected colour of a laminate restoration is significantly affected by the ceramic shade, ceramic thickness and resin cement shade. Using the WO shade resin cement seems to be more effective in masking the discoloured abutment tooth. Clinicians should also select the translucency level of the ceramic block with the shade when a leucite-based CAD/CAM system is chosen to treat a discoloured tooth. Copyright © 2013 Elsevier Ltd. All rights reserved.

Genotype x shade effects for western hemlock.

Treesearch

G.R. Johnson; C. Cartwright

2005-01-01

Western hemlock (Tsuga heterophylla (Raf.) Sarg.) families were grown under different levels of shade for 2 or 3 years at two nursery sites to determine whether families performed differently relative to one another in the different shade environments. Differences were found both for levels of shade and families, but no family x shade interaction...

Dental Shade Guide Variability for Hues B, C, and D Using Cross-Polarized Photography.

PubMed

Sampaio, Camila S; Gurrea, Jon; Gurrea, Marta; Bruguera, August; Atria, Pablo J; Janal, Malvin; Bonfante, Estevam A; Coelho, Paulo G; Hirata, Ronaldo

2018-04-20

This study evaluated the color variability of hues B, C, and D between the VITA Classical shade guide (Vita Zahnfabrik) and four other VITA-coded ceramic shade guides using a digital camera (Canon EOS 60D) and computer software (Adobe Photoshop CC). A cross-polarizing filter was used to standardize external light sources influencing color match. A total of 275 pictures were taken, 5 per shade tab, for 11 shades (B1, B2, B3, B4, C1, C2, C3, C4, D2, D3, and D4), from the following shade guides: VITA Classical (control); IPS e.max Ceram (Ivoclar Vivadent); IPS d.SIGN (Ivoclar Vivadent); Initial ZI (GC); and Creation CC (Creation Willi Geller). Pictures were evaluated using Adobe Photoshop CC for standardization of hue, chroma, and value between shade tabs. The VITA-coded shade guides evaluated here showed an overall unmatched shade in all their tabs when compared to the control, suggesting that shade selection should be made with the corresponding manufacturer guide of the ceramic intended for the final restoration.

Defect Related Dark Currents in III-V MWIR nBn Detectors

DTIC Science & Technology

2014-01-01

theory indicates a thermal activation energy of half the bandgap, and a direct proportionality between dark current density and defect density. 2.2...density due to defects maintains a full bandgap thermal activation energy , and is proportional to the square root of the defect density. Although neutral...photodiodes, and cooling is more efficient in reducing nBn’s dark current due to the full bandgap activation energy . Downloaded From: http

WIMP dark matter candidates and searches-current status and future prospects.

PubMed

Roszkowski, Leszek; Sessolo, Enrico Maria; Trojanowski, Sebastian

2018-06-01

We review several current aspects of dark matter theory and experiment. We overview the present experimental status, which includes current bounds and recent claims and hints of a possible signal in a wide range of experiments: direct detection in underground laboratories, gamma-ray, cosmic ray, x-ray, neutrino telescopes, and the LHC. We briefly review several possible particle candidates for a weakly interactive massive particle (WIMP) and dark matter that have recently been considered in the literature. We pay particular attention to the lightest neutralino of supersymmetry as it remains the best motivated candidate for dark matter and also shows excellent detection prospects. Finally we briefly review some alternative scenarios that can considerably alter properties and prospects for the detection of dark matter obtained within the standard thermal WIMP paradigm.

WIMP dark matter candidates and searches—current status and future prospects

NASA Astrophysics Data System (ADS)

Roszkowski, Leszek; Sessolo, Enrico Maria; Trojanowski, Sebastian

2018-06-01

We review several current aspects of dark matter theory and experiment. We overview the present experimental status, which includes current bounds and recent claims and hints of a possible signal in a wide range of experiments: direct detection in underground laboratories, gamma-ray, cosmic ray, x-ray, neutrino telescopes, and the LHC. We briefly review several possible particle candidates for a weakly interactive massive particle (WIMP) and dark matter that have recently been considered in the literature. We pay particular attention to the lightest neutralino of supersymmetry as it remains the best motivated candidate for dark matter and also shows excellent detection prospects. Finally we briefly review some alternative scenarios that can considerably alter properties and prospects for the detection of dark matter obtained within the standard thermal WIMP paradigm.

Evaluation of different shades to improve dairy cattle well-being in Argentina

NASA Astrophysics Data System (ADS)

Valtorta, S. E.; Leva, Perla E.; Gallardo, Miriam R.

Two tree shades (TS1 and TS2) and an artificial shade structure (AS) were evaluated using black globe temperatures (BGTs) to assess their effectiveness in reducing heat load. The artificial structure consisted of a black woven polypropylene cloth providing 80% shade, mounted on 2.5-m-high eucalyptus posts. The work was carried out at Rafaela Experimental Station, Argentina, during the summer (January and February) 1994. BGTs and floor temperatures were measured in concrete floor holding pens with and without artifical shade. The results showed no difference between TS1, TS2 and AS, their average BGTs being 30.2 (SD 0.58), 29.0 (SD 0.70) and 30.2 (SD 0.74)°C, respectively. BGTs under all three shades were significantly lower (P<0.01) than the average BGT recorded outside: 35.5 (SD 1.12)°C. Average BGTs in holding pens were 32.4 (SD 1.38) and 39.9 (SD 1.91)°C for shaded and non-shaded areas (P<0.01). The corresponding average floor temperatures were 27.8 (SD 0.68)°C and 47.7 (SD 2.13)°C (P<0.01). To assess the effects of shade on animal well-being, afternoon rectal temperatures (RT) and respiratory rate (respirations per minute, RR) of lactating cows were recorded twice a week. Rectal temperatures were significantly higher for non-shaded cows (P<0.01), mean RT being 40.1 (SD 0.65)°C vs 39.3 (SD 0.42)°C for the shaded animals. Corresponding RRs were 78.9 (SD 18.0) and 60.7 (SD 10.6) (P<0.05). It was concluded that: (1) tree and artificial shades produced similar effects, (2) shading the holding pen with an 80% shading cloth was effective in reducing heat load and floor temperatures, and (3) access to shade in our pasture-based system improved animal well-being.

A Novel Two-Step Method for Screening Shade Tolerant Mutant Plants via Dwarfism

PubMed Central

Li, Wei; Katin-Grazzini, Lorenzo; Krishnan, Sanalkumar; Thammina, Chandra; El-Tanbouly, Rania; Yer, Huseyin; Merewitz, Emily; Guillard, Karl; Inguagiato, John; McAvoy, Richard J.; Liu, Zongrang; Li, Yi

2016-01-01

When subjected to shade, plants undergo rapid shoot elongation, which often makes them more prone to disease and mechanical damage. Shade-tolerant plants can be difficult to breed; however, they offer a substantial benefit over other varieties in low-light areas. Although perennial ryegrass (Lolium perenne L.) is a popular species of turf grasses because of their good appearance and fast establishment, the plant normally does not perform well under shade conditions. It has been reported that, in turfgrass, induced dwarfism can enhance shade tolerance. Here we describe a two-step procedure for isolating shade tolerant mutants of perennial ryegrass by first screening for dominant dwarf mutants, and then screening dwarf plants for shade tolerance. The two-step screening process to isolate shade tolerant mutants can be done efficiently with limited space at early seedling stages, which enables quick and efficient isolation of shade tolerant mutants, and thus facilitates development of shade tolerant new cultivars of turfgrasses. Using the method, we isolated 136 dwarf mutants from 300,000 mutagenized seeds, with 65 being shade tolerant (0.022%). When screened directly for shade tolerance, we recovered only four mutants from a population of 150,000 (0.003%) mutagenized seeds. One shade tolerant mutant, shadow-1, was characterized in detail. In addition to dwarfism, shadow-1 and its sexual progeny displayed high degrees of tolerance to both natural and artificial shade. We showed that endogenous gibberellin (GA) content in shadow-1 was higher than wild-type controls, and shadow-1 was also partially GA insensitive. Our novel, simple and effective two-step screening method should be applicable to breeding shade tolerant cultivars of turfgrasses, ground covers, and other economically important crop plants that can be used under canopies of existing vegetation to increase productivity per unit area of land. PMID:27752260

Evaluation of different shades to improve dairy cattle well-being in Argentina.

PubMed

Valtorta, S E; Leva, P E; Gallardo, M R

1997-11-01

Two tree shades (TS1 and TS2) and an artificial shade structure (AS) were evaluated using black globe temperatures (BGTs) to assess their effectiveness in reducing heat load. The artificial structure consisted of a black woven polypropylene cloth providing 80% shade, mounted on 2.5-m-high eucalyptus posts. The work was carried out at Rafaela Experimental Station, Argentina, during the summer (January and February) 1994. BGTs and floor temperatures were measured in concrete floor holding pens with and without artificial shade. The results showed no difference between TS1, TS2 and AS, their average BGTs being 30.2 (SD 0.58), 29.0 (SD 0.70) and 30.2 (SD 0.74) degrees C, respectively. BGTs under all three shades were significantly lower (P < 0.01) than the average BGT recorded outside: 35.5 (SD 1.12) degrees C. Average BGTs in holding pens were 32.4 (SD 1.38) and 39.9 (SD 1.91) degrees C for shaded and non-shaded areas (P < 0.01). The corresponding average floor temperatures were 27.8 (SD 0.68) degrees C and 47.7 (SD 2.13) degrees C (P < 0.01). To assess the effects of shade on animal well-being, afternoon rectal temperatures (RT) and respiratory rate (respirations per minute, RR) of lactating cows were recorded twice a week. Rectal temperatures were significantly higher for non-shaded cows (P < 0.01), mean RT being 40.1 (SD 0.65) degrees C vs 39.3 (SD 0.42) degrees C for the shaded animals. Corresponding RRs were 78.9 (SD 18.0) and 60.7 (SD 10.6) (P < 0.05). It was concluded that: (1) tree and artificial shades produced similar effects, (2) shading the holding pen with an 80% shading cloth was effective in reducing heat load and floor temperatures, and (3) access to shade in our pasture-based system improved animal well-being.

[Response of photosynthetic characteristics of peanut seedlings leaves to low light].

PubMed

Zhang, Kun; Wan, Yong-shan; Liu, Feng-zhen; Zhang, Er-qun; Wang, Su

2009-12-01

To investigate the effects of shading and light recovery on the photosynthetic characteristics of peanut seedlings leaves, different shading treatments including no shading, 27% shading, 43% shading, and 77% shading were performed with black sunshade net at the seedling stage of two peanut cultivars Fenghua 1 and Fenghua 2, with related parameters determined. It was shown that with the increase of shading degree, the leaf chlorophyll content, actual PSII photochemical efficiency under irradiance (phi(PS II)), and maximum PS II photochemical efficiency (Fv/Fm) of test cultivars increased, while the Chl a/b ratio and photosynthetic rate (Pn) decreased. On the first day after light recovery, the Pn and stomatal conductance (Gs) decreased while the intercellular CO2 concentration (Ci) increased with increasing shading degree when measured under high light, but the Pn increased and the Gs and Ci decreased with increasing shading degree when measured under low light. The ratio of Pn measured under low light to that measured under high light increased significantly. With increasing shading degree, the light compensation point, light saturation point, CO2 compensation point, CO2 saturation point, and carboxylation efficiency decreased, while the apparent quantum yield increased. After the removal of shading, the Pn, phi(PS II), and Fv/Fm under natural light decreased immediately, but increased gradually 3-5 days after. 15 days after light recovery, the Pn, phi(PS II) and Fv/Fm in treatment 27% shading recovered to the level of no shading. As for the other treatments, the restored extent differed with shading degree and test variety. In the same treatments, the leaf chlorophyll content, Pn and phi(PS II) of Fenghua 1 were higher than those of Fenghua 2. The results demonstrated that shading at seedling stage improved the capabilities of test varieties in using low light, but reduced the capabilities in using high light.

Comparison of accuracies of an intraoral spectrophotometer and conventional visual method for shade matching using two shade guide systems.

PubMed

Parameswaran, Vidhya; Anilkumar, S; Lylajam, S; Rajesh, C; Narayan, Vivek

2016-01-01

This in vitro study compared the shade matching abilities of an intraoral spectrophotometer and the conventional visual method using two shade guides. The results of previous investigations between color perceived by human observers and color assessed by instruments have been inconclusive. The objectives were to determine accuracies and interrater agreement of both methods and effectiveness of two shade guides with either method. In the visual method, 10 examiners with normal color vision matched target control shade tabs taken from the two shade guides (VITAPAN Classical™ and VITAPAN 3D Master™) with other full sets of the respective shade guides. Each tab was matched 3 times to determine repeatability of visual examiners. The spectrophotometric shade matching was performed by two independent examiners using an intraoral spectrophotometer (VITA Easyshade™) with five repetitions for each tab. Results revealed that visual method had greater accuracy than the spectrophotometer. The spectrophotometer; however, exhibited significantly better interrater agreement as compared to the visual method. While VITAPAN Classical shade guide was more accurate with the spectrophotometer, VITAPAN 3D Master shade guide proved better with visual method. This in vitro study clearly delineates the advantages and limitations of both methods. There were significant differences between the methods with the visual method producing more accurate results than the spectrophotometric method. The spectrophotometer showed far better interrater agreement scores irrespective of the shade guide used. Even though visual shade matching is subjective, it is not inferior and should not be underrated. Judicious combination of both techniques is imperative to attain a successful and esthetic outcome.

Observational constraints on variable equation of state parameters of dark matter and dark energy after Planck

NASA Astrophysics Data System (ADS)

Kumar, Suresh; Xu, Lixin

2014-10-01

In this paper, we study a cosmological model in general relativity within the framework of spatially flat Friedmann-Robertson-Walker space-time filled with ordinary matter (baryonic), radiation, dark matter and dark energy, where the latter two components are described by Chevallier-Polarski-Linder equation of state parameters. We utilize the observational data sets from SNLS3, BAO and Planck + WMAP9 + WiggleZ measurements of matter power spectrum to constrain the model parameters. We find that the current observational data offer tight constraints on the equation of state parameter of dark matter. We consider the perturbations and study the behavior of dark matter by observing its effects on CMB and matter power spectra. We find that the current observational data favor the cold dark matter scenario with the cosmological constant type dark energy at the present epoch.

Minority carrier lifetime and dark current measurements in mid-wavelength infrared InAs 0.91Sb 0.09 alloy nBn photodetectors

DOE PAGES

Olson, B. V.; Kim, J. K.; Kadlec, E. A.; ...

2015-11-03

Carrier lifetime and dark current measurements are reported for a mid-wavelength infrared InAs 0.91Sb 0.09 alloy nBn photodetector. Minority carrier lifetimes are measured using a non-contact time-resolved microwave technique on unprocessed portions of the nBn wafer and the Auger recombination Bloch function parameter is determined to be |F 1F 2|=0.292. Moreover, the measured lifetimes are also used to calculate the expected diffusion dark current of the nBn devices and are compared with the experimental dark current measured in processed photodetector pixels from the same wafer. As a result, excellent agreement is found between the two, highlighting the important relationship betweenmore » lifetimes and diffusion currents in nBn photodetectors.« less

New entrance shade design for SIRTF

NASA Technical Reports Server (NTRS)

Davis, Paul K.

1989-01-01

A new design for the entrance shade for the Space Infrared Telescope Facility (SIRTF) is presented. The evolution of the entrance shade began with a simple frustum, symmetrical about the telescope axis, when SIRTF was expected to be Shuttle-attached. With the change to a free-flying SIRTF this frustum was cut off at an angle. The telescope will be operated so that whenever not in the earth's shadow the high side is kept toward the sun. However, the entrance shade interior itself will be so warm that the optics, including the secondary mirror and its mechanisms and support structure, will be restricted to the rear part of the barrel, termed the aftbaffle, which is shaded from the interior of the entrance shade by the forebaffle. This is best accomplished by the most recent design in which the axis of the entrance shade is offset from the telescope axis. This results in a shorter entrance shade, shorter forebaffle, and a shaded region within the barrel which is symmetrical about the telescope axis. All of these are advantageous.

Prospects of direct search for dark photon and dark Higgs in SeaQuest/E1067 experiment at the Fermilab main injector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Ming Xiong

In this study, we present the current status and prospects of the dark sector physics search program of the SeaQuest/E1067 fixed target dimuon experiment at Fermilab Main Injector. There has been tremendous excitement and progress in searching for new physics in the dark sector in recent years. Dark sector refers to a collection of currently unknown particles that do not directly couple with the Standard Model (SM) strong and electroweak (EW) interactions but assumed to carry gravitational force, thus could be candidates of the missing Dark Matter (DM). Such particles may interact with the SM particles through “portal” interactions. Twomore » of the simple possibilities are being investigated in our initial search: (1) dark photon and (2) dark Higgs. They could be within immediate reach of current or near future experimental search. We show there is a unique opportunity today at Fermilab to directly search for these particles in a highly motivated but uncharted parameter space in high-energy proton–nucleus collisions in the beam-dump mode using the 120 GeV proton beam from the Main Injector. Our current search window covers the mass range 0.2–10 GeV/c 2, and in the near future, by adding an electromagnetic calorimeter (EMCal) to the spectrometer, we can further explore the lower mass region down to about ~1 MeV/c 2 through the di-electron channel. If dark photons (and/or dark Higgs) were observed, they would revolutionize our understanding of the fundamental structures and interactions of our universe.« less

Prospects of direct search for dark photon and dark Higgs in SeaQuest/E1067 experiment at the Fermilab main injector

DOE PAGES

Liu, Ming Xiong

2017-03-14

In this study, we present the current status and prospects of the dark sector physics search program of the SeaQuest/E1067 fixed target dimuon experiment at Fermilab Main Injector. There has been tremendous excitement and progress in searching for new physics in the dark sector in recent years. Dark sector refers to a collection of currently unknown particles that do not directly couple with the Standard Model (SM) strong and electroweak (EW) interactions but assumed to carry gravitational force, thus could be candidates of the missing Dark Matter (DM). Such particles may interact with the SM particles through “portal” interactions. Twomore » of the simple possibilities are being investigated in our initial search: (1) dark photon and (2) dark Higgs. They could be within immediate reach of current or near future experimental search. We show there is a unique opportunity today at Fermilab to directly search for these particles in a highly motivated but uncharted parameter space in high-energy proton–nucleus collisions in the beam-dump mode using the 120 GeV proton beam from the Main Injector. Our current search window covers the mass range 0.2–10 GeV/c 2, and in the near future, by adding an electromagnetic calorimeter (EMCal) to the spectrometer, we can further explore the lower mass region down to about ~1 MeV/c 2 through the di-electron channel. If dark photons (and/or dark Higgs) were observed, they would revolutionize our understanding of the fundamental structures and interactions of our universe.« less

Impacts of Topographic Shading on Surface Energy Balance of High Mountain Asia Glaciers

NASA Astrophysics Data System (ADS)

Olson, M.; Rupper, S.

2016-12-01

Topographic shading plays an important role in the energy balance of valley glaciers. While previous studies incorporate shading of varying complexity in surface energy balance models, to date, no large-scale studies have explored in depth the effects of topographic shading on glacier surface energy balance, and how these vary geographically within High Mountain Asia (HMA). Here we develop a model to examine the variability in potential insolation during the summer melt season using the ASTER GDEM and multi-hour solar geometry to simulate topographic shading on an idealized glacier. Shading is calculated in simulations utilizing a range of slopes, aspects, and latitudes. We test glacier mass balance sensitivity to these parameters for a suite of glaciers throughout HMA. Our results show that shading impacts on glaciers in HMA are highly variable across different geographic regions, but that they are largely predictable based on topographic characteristics such as slope and aspect. For example, we find in regions with steep topography and high relief that shading frequently dominates in the ablation zone rather than the accumulation zone, contrary to the findings of some previous studies. In these regions, topographic shading may play a more significant role in glacier energy balance. These results will better define the effects of topographic shading on surface energy balance, and improve model accuracy within HMA. Additionally, this topographic shading model provides a framework to quantify how shading effects vary for advancing or retreating glaciers as they respond to fluctuations in climate across HMA.

Optical properties of current ceramics systems for laminate veneers.

PubMed

Bagis, Bora; Turgut, Sedanur

2013-08-01

Full-ceramic systems can be produced by different techniques (layering, heatpressing, CAD/CAM) and have various compositions with different crystalline contents that may affect the optical properties of laminate restorations. A total of 60 specimens were prepared from e.max Press, e.max CAD, Empress Esthetic, e.max Ceram, Inline, and ZirPress systems (A1 shade; diameter 10mm; thickness 0.5 ± 0.05mm). The L*, a*, and b* values, chroma and translucency (TP) of each system were recorded before and after ageing. The statistical analyses were performed by ANOVA, Tukey's tests and the paired sample t-test (p<0.05). The L* value of the shade guide was significantly different from those of the full-ceramic systems; however, there were no significant differences between the a* values of Ceram, Esthetic, Inline and Zirpress. There were significant differences between the b* values of the shade guide compared with the full-ceramics except for e.max Press. The L* values decreased, and the a* and b* values increased after the ageing process for all groups. There were no significant differences between the ΔE values of the ceramic systems (p>0.05). The TP values decreased, and the chroma value increased significantly after the ageing process (p>0.05). The chroma of the shade guide was found to be the highest. None of the full-ceramic systems was able to match the color of the shade guide. The chemical structures of the ceramic systems were more effective for determining the optical parameters than the fabrication techniques. Ageing caused full-ceramics to become more opaque, darker, reddish and yellowish. Copyright © 2012 Elsevier Ltd. All rights reserved.

Shade selection performed by novice dental professionals and colorimeter.

PubMed

Klemetti, E; Matela, A-M; Haag, P; Kononen, M

2006-01-01

The objective of this study was to test inter-observer variability in shade selection for porcelain restorations, using three different shade guides: Vita Lumin Vacuum, Vita 3D-Master and Procera. Nineteen young dental professionals acted as observers. The results were also compared with those of a digital colorimeter (Shade Eye Ex; Shofu, Japan). Regarding repeatability, no significant differences were found between the three shade guides, although repeatability was relatively low (33-43%). Agreement with the colorimetric results was also low (8-34%). In conclusion, shade selection shows moderate to great inter-observer variation. In teaching and standardizing the shade selection procedure, a digital colorimeter may be a useful educational tool.

Proposed shade guide for human facial skin and lip: a pilot study.

PubMed

Wee, Alvin G; Beatty, Mark W; Gozalo-Diaz, David J; Kim-Pusateri, Seungyee; Marx, David B

2013-08-01

Currently, no commercially available facial shade guide exists in the United States for the fabrication of facial prostheses. The purpose of this study was to measure facial skin and lip color in a human population sample stratified by age, gender, and race. Clustering analysis was used to determine optimal color coordinates for a proposed facial shade guide. Participants (n=119) were recruited from 4 racial/ethnic groups, 5 age groups, and both genders. Reflectance measurements of participants' noses and lower lips were made by using a spectroradiometer and xenon arc lamp with a 45/0 optical configuration. Repeated measures ANOVA (α=.05), to identify skin and lip color differences, resulting from race, age, gender, and location, and a hierarchical clustering analysis, to identify clusters of skin colors) were used. Significant contributors to L*a*b* facial color were race and facial location (P<.01). b* affected all factors (P<.05). Age affected only b* (P<.001), while gender affected only L* (P<.05) and b* (P<.05). Analyses identified 5 clusters of skin color. The study showed that skin color caused by age and gender primarily occurred within the yellow-blue axis. A significant lightness difference between gender groups was also found. Clustering analysis identified 5 distinct skin shade tabs. Copyright © 2013 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Cacao Cultivation under Diverse Shade Tree Cover Allows High Carbon Storage and Sequestration without Yield Losses

PubMed Central

Abou Rajab, Yasmin; Leuschner, Christoph; Barus, Henry; Tjoa, Aiyen; Hertel, Dietrich

2016-01-01

One of the main drivers of tropical forest loss is their conversion to oil palm, soy or cacao plantations with low biodiversity and greatly reduced carbon storage. Southeast Asian cacao plantations are often established under shade tree cover, but are later converted to non-shaded monocultures to avoid resource competition. We compared three co-occurring cacao cultivation systems (3 replicate stands each) with different shade intensity (non-shaded monoculture, cacao with the legume Gliricidia sepium shade trees, and cacao with several shade tree species) in Sulawesi (Indonesia) with respect to above- and belowground biomass and productivity, and cacao bean yield. Total biomass C stocks (above- and belowground) increased fivefold from the monoculture to the multi-shade tree system (from 11 to 57 Mg ha-1), total net primary production rose twofold (from 9 to 18 Mg C ha-1 yr-1). This increase was associated with a 6fold increase in aboveground biomass, but only a 3.5fold increase in root biomass, indicating a clear shift in C allocation to aboveground tree organs with increasing shade for both cacao and shade trees. Despite a canopy cover increase from 50 to 93%, cacao bean yield remained invariant across the systems (variation: 1.1–1.2 Mg C ha-1 yr-1). The monocultures had a twice as rapid leaf turnover suggesting that shading reduces the exposure of cacao to atmospheric drought, probably resulting in greater leaf longevity. Thus, contrary to general belief, cacao bean yield does not necessarily decrease under shading which seems to reduce physical stress. If planned properly, cacao plantations under a shade tree cover allow combining high yield with benefits for carbon sequestration and storage, production system stability under stress, and higher levels of animal and plant diversity. PMID:26927428

In response to partial plant shading, the lack of phytochrome A does not directly induce leaf senescence but alters the fine-tuning of chlorophyll biosynthesis

PubMed Central

Brouwer, Bastiaan; Gardeström, Per; Keech, Olivier

2014-01-01

Phytochrome is thought to control the induction of leaf senescence directly, however, the signalling and molecular mechanisms remain unclear. In the present study, an ecophysiological approach was used to establish a functional connection between phytochrome signalling and the physiological processes underlying the induction of leaf senescence in response to shade. With shade it is important to distinguish between complete and partial shading, during which either the whole or only a part of the plant is shaded, respectively. It is first shown here that, while PHYB is required to maintain chlorophyll content in a completely shaded plant, only PHYA is involved in maintaining the leaf chlorophyll content in response to partial plant shading. Second, it is shown that leaf yellowing associated with strong partial shading in phyA-mutant plants actually correlates to a decreased biosynthesis of chlorophyll rather than to an increase of its degradation. Third, it is shown that the physiological impact of this decreased biosynthesis of chlorophyll in strongly shaded phyA-mutant leaves is accompanied by a decreased capacity to adjust the Light Compensation Point. However, the increased leaf yellowing in phyA-mutant plants is not accompanied by an increase of senescence-specific molecular markers, which argues against a direct role of PHYA in inducing leaf senescence in response to partial shade. In conclusion, it is proposed that PHYA, but not PHYB, is essential for fine-tuning the chlorophyll biosynthetic pathway in response to partial shading. In turn, this mechanism allows the shaded leaf to adjust its photosynthetic machinery to very low irradiances, thus maintaining a positive carbon balance and repressing the induction of leaf senescence, which can occur under prolonged periods of shade. PMID:24604733

Cacao Cultivation under Diverse Shade Tree Cover Allows High Carbon Storage and Sequestration without Yield Losses.

PubMed

Abou Rajab, Yasmin; Leuschner, Christoph; Barus, Henry; Tjoa, Aiyen; Hertel, Dietrich

2016-01-01

One of the main drivers of tropical forest loss is their conversion to oil palm, soy or cacao plantations with low biodiversity and greatly reduced carbon storage. Southeast Asian cacao plantations are often established under shade tree cover, but are later converted to non-shaded monocultures to avoid resource competition. We compared three co-occurring cacao cultivation systems (3 replicate stands each) with different shade intensity (non-shaded monoculture, cacao with the legume Gliricidia sepium shade trees, and cacao with several shade tree species) in Sulawesi (Indonesia) with respect to above- and belowground biomass and productivity, and cacao bean yield. Total biomass C stocks (above- and belowground) increased fivefold from the monoculture to the multi-shade tree system (from 11 to 57 Mg ha-1), total net primary production rose twofold (from 9 to 18 Mg C ha-1 yr-1). This increase was associated with a 6fold increase in aboveground biomass, but only a 3.5fold increase in root biomass, indicating a clear shift in C allocation to aboveground tree organs with increasing shade for both cacao and shade trees. Despite a canopy cover increase from 50 to 93%, cacao bean yield remained invariant across the systems (variation: 1.1-1.2 Mg C ha-1 yr-1). The monocultures had a twice as rapid leaf turnover suggesting that shading reduces the exposure of cacao to atmospheric drought, probably resulting in greater leaf longevity. Thus, contrary to general belief, cacao bean yield does not necessarily decrease under shading which seems to reduce physical stress. If planned properly, cacao plantations under a shade tree cover allow combining high yield with benefits for carbon sequestration and storage, production system stability under stress, and higher levels of animal and plant diversity.

Satisfaction of Dental Students, Faculty, and Patients with Tooth Shade-Matching Using a Spectrophotometer.

PubMed

Ballard, Erin; Metz, Michael J; Harris, Bryan T; Metz, Cynthia J; Chou, Jang-Ching; Morton, Dean; Lin, Wei-Shao

2017-05-01

The aims of this study were to evaluate dental students' clinical shade-matching outcomes (from subjective use of shade guide) with an objective electronic shade-matching tool (spectrophotometer); to assess patients', students', and supervising faculty members' satisfaction with the clinical shade-matching outcomes; and to assess clinicians' support for use of the spectrophotometer to improve esthetic outcomes. A total of 103 volunteer groups, each consisting of patient, dental student, and supervising faculty member at the University of Louisville, were recruited to participate in the study in 2015. Using the spectrophotometer, clinical shade-matching outcome (ΔE clinical ) and laboratory shade-matching outcome (ΔE laboratory ) were calculated. Two five-point survey items were used to assess the groups' satisfaction with the clinical shade-matching outcome and support for an objective electronic shade-matching tool in the student clinic. The results showed that both ΔE clinical (6.5±2.4) and ΔE laboratory (4.3±2.0) were outside the clinical acceptability threshold ΔE values of 2.7, when visual shade-matching method (subjective usage of shade guide) was used to fabricate definitive restorations. Characteristics of the patients, dental students, supervising faculty members, and restorations had minimal to no effect on the ΔE clinical The patients, dental students, and supervising faculty members generally had positive opinions about the clinical shade-matching outcome, despite the increased ΔE clinical observed. Overall, clinical shade-matching outcomes in this school need further improvement, but the patients' positive opinions may indicate the need to revisit the acceptability threshold ΔE value of 2.7 in the academic setting.

Comparison of accuracies of an intraoral spectrophotometer and conventional visual method for shade matching using two shade guide systems

PubMed Central

Parameswaran, Vidhya; Anilkumar, S.; Lylajam, S.; Rajesh, C.; Narayan, Vivek

2016-01-01

Background and Objectives: This in vitro study compared the shade matching abilities of an intraoral spectrophotometer and the conventional visual method using two shade guides. The results of previous investigations between color perceived by human observers and color assessed by instruments have been inconclusive. The objectives were to determine accuracies and interrater agreement of both methods and effectiveness of two shade guides with either method. Methods: In the visual method, 10 examiners with normal color vision matched target control shade tabs taken from the two shade guides (VITAPAN Classical™ and VITAPAN 3D Master™) with other full sets of the respective shade guides. Each tab was matched 3 times to determine repeatability of visual examiners. The spectrophotometric shade matching was performed by two independent examiners using an intraoral spectrophotometer (VITA Easyshade™) with five repetitions for each tab. Results: Results revealed that visual method had greater accuracy than the spectrophotometer. The spectrophotometer; however, exhibited significantly better interrater agreement as compared to the visual method. While VITAPAN Classical shade guide was more accurate with the spectrophotometer, VITAPAN 3D Master shade guide proved better with visual method. Conclusion: This in vitro study clearly delineates the advantages and limitations of both methods. There were significant differences between the methods with the visual method producing more accurate results than the spectrophotometric method. The spectrophotometer showed far better interrater agreement scores irrespective of the shade guide used. Even though visual shade matching is subjective, it is not inferior and should not be underrated. Judicious combination of both techniques is imperative to attain a successful and esthetic outcome. PMID:27746599

Pixel pitch and particle energy influence on the dark current distribution of neutron irradiated CMOS image sensors.

PubMed

Belloir, Jean-Marc; Goiffon, Vincent; Virmontois, Cédric; Raine, Mélanie; Paillet, Philippe; Duhamel, Olivier; Gaillardin, Marc; Molina, Romain; Magnan, Pierre; Gilard, Olivier

2016-02-22

The dark current produced by neutron irradiation in CMOS Image Sensors (CIS) is investigated. Several CIS with different photodiode types and pixel pitches are irradiated with various neutron energies and fluences to study the influence of each of these optical detector and irradiation parameters on the dark current distribution. An empirical model is tested on the experimental data and validated on all the irradiated optical imagers. This model is able to describe all the presented dark current distributions with no parameter variation for neutron energies of 14 MeV or higher, regardless of the optical detector and irradiation characteristics. For energies below 1 MeV, it is shown that a single parameter has to be adjusted because of the lower mean damage energy per nuclear interaction. This model and these conclusions can be transposed to any silicon based solid-state optical imagers such as CIS or Charged Coupled Devices (CCD). This work can also be used when designing an optical imager instrument, to anticipate the dark current increase or to choose a mitigation technique.

Waveguide-integrated vertical pin photodiodes of Ge fabricated on p+ and n+ Si-on-insulator layers

NASA Astrophysics Data System (ADS)

Ito, Kazuki; Hiraki, Tatsurou; Tsuchizawa, Tai; Ishikawa, Yasuhiko

2017-04-01

Vertical pin structures of Ge photodiodes (PDs) integrated with Si optical waveguides are fabricated by depositing Ge epitaxial layers on Si-on-insulator (SOI) layers, and the performances of n+-Ge/i-Ge/p+-SOI PDs are compared with those of p+-Ge/i-Ge/n+-SOI PDs. Both types of PDs show responsivities as high as 1.0 A/W at 1.55 µm, while the dark leakage current is different, which is consistent with previous reports on free-space PDs formed on bulk Si wafers. The dark current of the p+-Ge/i-Ge/n+-SOI PDs is higher by more than one order of magnitude. Taking into account the activation energies for dark current as well as the dependence on PD area, the dark current of the n+-Ge/i-Ge/p+-SOI PDs is dominated by the thermal generation of carriers via mid-gap defect levels in Ge, while for the p+-Ge/i-Ge/n+-SOI PDs, the dark current is ascribed to not only thermal generation but also other mechanisms such as locally formed conduction paths.

Increased growth of young citrus trees under reduced radiation load in a semi-arid climate.

PubMed

Raveh, E; Cohen, S; Raz, T; Yakir, D; Grava, A; Goldschmidt, E E

2003-01-01

This study investigated the effects of radiation heat-load reduction by shading on the growth and development of citrus trees in a warm subtropical region. The experiment was conducted from mid-June until late October when daily maximal air temperature averaged 29.3 degrees C. Two-year-old de-fruited Murcott tangor (Citrus reticulata BlancoxCitrus sinensis (L.) Osb.) trees were grown under 30% or 60% shade tunnels, or 60% flat shade (providing midday shade only), using highly reflective aluminized nets. Non-shaded trees were used as the control. Shading reduced direct more than diffuse radiation. Daily radiation was reduced by 35% for the 30% Tunnel and 60% Flat treatments, and by 55% for the 60% Tunnel. Two days of intensive measurement showed that shading increased average sunlit leaf conductance by 44% and photosynthesis by 29%. Shading did not significantly influence root and stem dry weight growth, but it increased the increment in leaf dry weight during the three month period by an average of 28% relative to the control, while final tree height in the 30% Tunnel treatment exceeded the control by 35%. Shoot to root and shoot mass ratios increased and root mass ratio decreased due to shading because of the increase in leaf dry weight. Shading increased starch concentration in leaves while the shadiest treatment, 60% Tunnel, decreased starch concentration in the roots. Carbon isotope ratio (delta(13)C) of exposed leaves that developed under shading was significantly reduced by 1.9 per thousand in the 60% Tunnel, indicating that shading increased CO(2) concentrations at the chloroplasts (C(c)), as would be expected from increased conductance. Substomatal CO(2) concentrations, C(i), computed from leaf net CO(2) assimilation rate and conductance values, also indicate that shading increases internal CO(2) concentrations. Based on tree dry mass, tree height, and total carbohydrates fractions, the 30% Tunnel and the 60% Flat were the optimal shade treatments.

Dark matter and dark energy interactions: theoretical challenges, cosmological implications and observational signatures.

PubMed

Wang, B; Abdalla, E; Atrio-Barandela, F; Pavón, D

2016-09-01

Models where dark matter and dark energy interact with each other have been proposed to solve the coincidence problem. We review the motivations underlying the need to introduce such interaction, its influence on the background dynamics and how it modifies the evolution of linear perturbations. We test models using the most recent observational data and we find that the interaction is compatible with the current astronomical and cosmological data. Finally, we describe the forthcoming data sets from current and future facilities that are being constructed or designed that will allow a clearer understanding of the physics of the dark sector.

Spiral MRI on a 9.4T Vertical-bore Superconducting Magnet Using Unshielded and Self-shielded Gradient Coils

PubMed Central

Kodama, Nao; Setoi, Ayana; Kose, Katsumi

2018-01-01

Spiral MRI sequences were developed for a 9.4T vertical standard bore (54 mm) superconducting magnet using unshielded and self-shielded gradient coils. Clear spiral images with 64-shot scan were obtained with the self-shielded gradient coil, but severe shading artifacts were observed for the spiral-scan images acquired with the unshielded gradient coil. This shading artifact was successfully corrected with a phase-correction technique using reference scans that we developed based on eddy current field measurements. We therefore concluded that spiral imaging sequences can be installed even for unshielded gradient coils if phase corrections are performed using the reference scans. PMID:28367906

Spiral MRI on a 9.4T Vertical-bore Superconducting Magnet Using Unshielded and Self-shielded Gradient Coils.

PubMed

Kodama, Nao; Setoi, Ayana; Kose, Katsumi

2018-04-10

Spiral MRI sequences were developed for a 9.4T vertical standard bore (54 mm) superconducting magnet using unshielded and self-shielded gradient coils. Clear spiral images with 64-shot scan were obtained with the self-shielded gradient coil, but severe shading artifacts were observed for the spiral-scan images acquired with the unshielded gradient coil. This shading artifact was successfully corrected with a phase-correction technique using reference scans that we developed based on eddy current field measurements. We therefore concluded that spiral imaging sequences can be installed even for unshielded gradient coils if phase corrections are performed using the reference scans.

13. VIEW OF CONTROL CONSOLE CURRENTLY USED ON OCCASION FOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW OF CONTROL CONSOLE CURRENTLY USED ON OCCASION FOR AMATUER RADIO AND TO PERIODICALLY ACTIVE STATION KPS. NOTE CLOCK ON WALL. SHADED PORTIONS ON 24HR CLOCK (15-18 AND 45-48 MINUTES) INDICATED MINUTES EACH HOUR WHEN STATIONS WOULD NOT TRANSMIT AND LISTEN FOR WEAK DISTRESS SIGNALS. - Marconi Radio Sites, Receiving, Point Reyes Station, Marin County, CA

Tweed Extinct Volcano, Australia, Stereo Pair of SRTM Shaded Relief and Colored Height

NASA Image and Video Library

2005-01-06

Australia is the only continent without any current volcanic activity, but it hosts one of the world largest extinct volcanoes, the Tweed Volcano. Rock dating methods indicate that eruptions here lasted about three million years.

Properly placed shade trees reduce summertime electricity bills in Sacramento, California

Treesearch

Geoffery H. Donovan; David R. Butry

2009-01-01

The discovery that shade trees can reduce home cooling costs is hardly surprising. Anybody who has sat under a tree on a warm summer day understands the shade benefit of trees. However, quantifying the effect a shade tree has on home energy use and carbon footprint, and identifying the optimal location for a shade tree, is less straightforward. Past studies that have...

Light-Induced Indeterminacy Alters Shade-Avoiding Tomato Leaf Morphology1[OPEN

PubMed Central

Chitwood, Daniel H.; Kumar, Ravi; Ranjan, Aashish; Pelletier, Julie M.; Townsley, Brad T.; Ichihashi, Yasunori; Martinez, Ciera C.; Zumstein, Kristina; Harada, John J.; Maloof, Julin N.; Sinha, Neelima R.

2015-01-01

Plants sense the foliar shade of competitors and alter their developmental programs through the shade-avoidance response. Internode and petiole elongation, and changes in overall leaf area and leaf mass per area, are the stereotypical architectural responses to foliar shade in the shoot. However, changes in leaf shape and complexity in response to shade remain incompletely, and qualitatively, described. Using a meta-analysis of more than 18,000 previously published leaflet outlines, we demonstrate that shade avoidance alters leaf shape in domesticated tomato (Solanum lycopersicum) and wild relatives. The effects of shade avoidance on leaf shape are subtle with respect to individual traits but are combinatorially strong. We then seek to describe the developmental origins of shade-induced changes in leaf shape by swapping plants between light treatments. Leaf size is light responsive late into development, but patterning events, such as stomatal index, are irrevocably specified earlier. Observing that shade induces increases in shoot apical meristem size, we then describe gene expression changes in early leaf primordia and the meristem using laser microdissection. We find that in leaf primordia, shade avoidance is not mediated through canonical pathways described in mature organs but rather through the expression of KNOTTED1-LIKE HOMEOBOX and other indeterminacy genes, altering known developmental pathways responsible for patterning leaf shape. We also demonstrate that shade-induced changes in leaf primordium gene expression largely do not overlap with those found in successively initiated leaf primordia, providing evidence against classic hypotheses that shaded leaf morphology results from the prolonged production of juvenile leaf types. PMID:26381315

[Effects of shading in summer and autumn on physiological and biochemical characteristics of 'Huangjinya' in Shandong Province, China].

PubMed

Tian, Yue Yue; Zhang, Li Xia; Zhang, Zheng Qun; Qiao, Ming Ming; Fan, Yan Gen

2017-03-18

In order to ensure the suitable shade model for 'Huangjinya' tea plant in Shandong Province, black or blue shading net at 55%, 70% or 85% shading rates was selected to recover tea garden in summer and autumn, then micro-climate of tea garden, leaf color, chlorophyll fluorescence parameters, growth status and biochemical composition of tea shoots were investigated.The results showed that compared with the control, light intensity and air temperature in tea garden, leaf temperature of tea plants in different shading treatments significantly decreased, while air humidity in tea garden increased. The contents of chlorophyll in the tea leaves were obviously increased with increasing the shading rate, which resulted in the leaf color becoming green. The yellowing characteristics and biochemical quality of 'Huangjinya' tea plants could be well kept in 55% shading treatments. In 70% shading treatments, 'Huangjinya' tea plants had better growth situation and higher yield with no photo-inhibition. Compared with the blue shading treatments, black shading treatments could obviously promote the growth of 'Huangjinya' tea plants, keep yellowing characteristics, and improve the quality. Therefore, the 70% black shading treatment (daily PAR values of 1.2-3.5 ten thousand lx) was appropriate for promoting the growth of 'Huangjinya' tea plants at the seedling stage. For mature tea plants, the 55% black shading treatment (daily PAR values of 1.8-5.5 ten thousand lx) could be used to keep the yellowing characteristics and to improve biochemical quality effectively, so as to give full play to its variety characteristics, to achieve goal of high quality and high yield.

Effects of shading on plant growth, flower quality and photosynthetic capacity of Rosa hybrida

NASA Astrophysics Data System (ADS)

Hou, Wei; Luo, Ya; Wang, Xiaorong; Chen, Qing; Sun, Bo; Wang, Yan; Liu, Zejing; Tang, Haoru; Zhang, Yong

2018-04-01

With the acceleration of the urbanization process, numbers of garden plants are grown in shaded environment. Rose (Rosa hybrida) is one of the most important ornamental plants used in urban green spaces. In the present study, effects of shading on plant growth, flower quality and photosynthetic capacity of R. hybrida were investigated. The results showed that shade not only delayed the initial flowering date, but also prolonged the flowering time. The physiological indices, including flower fresh weight, total anthocyanins and flavonoids contents, were lower in plants grown with shade compared with those grown in sun exposure. Overall, R. hybrida seemed to be a shade adapted plant which could be successfully grown in urban green spaces or understory with slight shade.

Current–voltage characteristics of organic heterostructure devices with insulating spacer layers

DOE PAGES

Yin, Sun; Nie, Wanyi; Mohite, Aditya D.; ...

2015-05-14

The dark current density in donor/acceptor organic planar heterostructure devices at a given forward voltage bias can either increase or decrease when an insulating spacer layer is added between the donor and acceptor layers. The dominant current flow process in these systems involves the formation and subsequent recombination of interfacial exciplex states. If the exciplex recombination rate limits current flow, an insulating interface layer decreases the dark current. However, if the exciplex formation rate limits the current, an insulating interface layer may increase the dark current. As a result, we present a device model to describe this behavior, and wemore » discuss relevant experimental data.« less

Color-Matching and Blending-Effect of Universal Shade Bulk-Fill-Resin-Composite in Resin-Composite-Models and Natural Teeth.

PubMed

Abdelraouf, Rasha M; Habib, Nour A

2016-01-01

Objectives . To assess visually color-matching and blending-effect (BE) of a universal shade bulk-fill-resin-composite placed in resin-composite-models with different shades and cavity sizes and in natural teeth (extracted and patients' teeth). Materials and Methods . Resin-composite-discs (10 mm × 1 mm) were prepared of universal shade composite and resin-composite of shades: A1, A2, A3, A3.5, and A4. Spectrophotometric-color-measurement was performed to calculate color-difference (Δ E ) between the universal shade and shaded-resin-composites discs and determine their translucency-parameter (TP). Visual assessment was performed by seven normal-color-vision-observers to determine the color-matching between the universal shade and each shade, under Illuminant D65. Color-matching visual scoring (VS) values were expressed numerically (1-5): 1: mismatch/totally unacceptable, 2: Poor-Match/hardly acceptable, 3: Good-Match/acceptable, 4: Close-Match/small-difference, and 5: Exact-Match/no-color-difference. Occlusal cavities of different sizes were prepared in teeth-like resin-composite-models with shades A1, A2, A3, A3.5, and A4. The cavities were filled by the universal shade composite. The same scale was used to score color-matching between the fillings and composite-models. BE was calculated as difference in mean-visual-scores in models and that of discs. Extracted teeth with two different class I-cavity sizes as well as ten patients' lower posterior molars with occlusal caries were prepared, filled by universal shade composite, and assessed similarly. Results . In models, the universal shade composite showed close matching in the different cavity sizes and surrounding shades (4 ≤ VS < 5) (BE = 0.6-2.9 in small cavities and 0.5-2.8 in large cavities). In extracted teeth, there was good-to-close color-matching (VS = 3.7-4.4 in small cavities, BE = 2.5-3.2) (VS = 3-3.5, BE = 1.8-2.3 in large cavities). In patients' molars, the universal shade composite showed good-matching (VS = 3-3.3, BE = -0.9-2.1). Conclusions . Color-matching of universal shade resin-composite was satisfactory rather than perfect in patients' teeth.

Viking Lander 2 Anniversary

NASA Image and Video Library

2002-12-13

This portion of NASA Mars Odyssey image covers NASA Viking 2 landing site shown with the X. The second landing on Mars took place September 3, 1976 in Utopia Planitia. The exact location of Lander 2 is not as well established as Lander 1 because there were no clearly identifiable features in the lander images as there were for the site of Lander 1. The Utopia landing site region contains pedestal craters, shallow swales and gentle ridges. The crater Goldstone was named in honor of the Tracking Station in the desert of California. The two Viking Landers operated for over 6 years (nearly four martian years) after landing. This one band IR (band 9 at 12.6 microns) image shows bright and dark textures, which are primarily due to differences in the abundance of rocks on the surface. The relatively cool (dark) regions during the day are rocky or indurated materials, fine sand and dust are warmer (bright). Many of the temperature variations are due to slope effects, with sun-facing slopes warmer than shaded slopes. The dark rings around several of the craters are due to the presence of rocky (cool) material ejected from the crater. These rocks are well below the resolution of any existing Mars camera, but THEMIS can detect the temperature variations they produce. Daytime temperature variations are produced by a combination of topographic (solar heating) and thermophysical (thermal inertia and albedo) effects. Due to topographic heating the surface morphologies seen in THEMIS daytime IR images are similar to those seen in previous imagery and MOLA topography. http://photojournal.jpl.nasa.gov/catalog/PIA04023

Large Synoptic Survey Telescope: From Science Drivers to Reference Design

DTIC Science & Technology

2008-01-01

faint time domain. The LSST design is driven by four main science themes: constraining dark energy and dark matter , taking an inventory of the Solar...Energy and Dark Matter (2) Taking an Inventory of the Solar System (3) Exploring the Transient Optical Sky (4) Mapping the Milky Way Each of these four...Constraining Dark Energy and Dark Matter Current models of cosmology require the exis- tence of both dark matter and dark energy to match observational

Reconciling species-level vs plastic responses of evergreen leaf structure to light gradients: shade leaves punch above their weight.

PubMed

Lusk, Christopher H; Onoda, Yusuke; Kooyman, Robert; Gutiérrez-Girón, Alba

2010-04-01

*When grown in a common light environment, the leaves of shade-tolerant evergreen trees have a larger leaf mass per unit area (LMA) than their light-demanding counterparts, associated with differences in lifespan. Yet plastic responses of LMA run counter to this pattern: shade leaves have smaller LMA than sun leaves, despite often living longer. *We measured LMA and cell wall content, and conducted punch and shear tests, on sun and shade leaves of 13 rainforest evergreens of differing shade tolerance, in order to understand adaptation vs plastic responses of leaf structure and biomechanics to shade. *Species shade tolerance and leaf mechanical properties correlated better with cell wall mass per unit area than with LMA. Growth light environment had less effect on leaf mechanics than on LMA: shade leaves had, on average, 40% lower LMA than sun leaves, but differences in work-to-shear, and especially force-to-punch, were smaller. This was associated with a slightly larger cell wall fraction in shade leaves. *The persistence of shade leaves might reflect unattractiveness to herbivores because they yield smaller benefits (cell contents per area) per unit fracture force than sun leaves. In forest trees, cell wall fraction and force-to-punch are more robust correlates of species light requirements than LMA.

Exoplanet Coronagraph Shaped Pupil Masks and Laboratory Scale Star Shade Masks: Design, Fabrication and Characterization

NASA Technical Reports Server (NTRS)

Balasubramanian, Kunjithapatha; White, Victor; Yee, Karl; Echternach, Pierre; Muller, Richard; Dickie, Matthew; Cady, Eric; Mejia Prada, Camilo; Ryan, Daniel; Poberezhskiy, Ilya;

Exoplanet coronagraph shaped pupil masks and laboratory scale star shade masks: design, fabrication and characterization

NASA Astrophysics Data System (ADS)

Balasubramanian, Kunjithapatham; White, Victor; Yee, Karl; Echternach, Pierre; Muller, Richard; Dickie, Matthew; Cady, Eric; Mejia Prada, Camilo; Ryan, Daniel; Poberezhskiy, Ilya; Zhou, Hanying; Kern, Brian; Riggs, A. J.; Zimmerman, Neil T.; Sirbu, Dan; Shaklan, Stuart; Kasdin, Jeremy

2015-09-01

Star light suppression technologies to find and characterize faint exoplanets include internal coronagraph instruments as well as external star shade occulters. Currently, the NASA WFIRST-AFTA mission study includes an internal coronagraph instrument to find and characterize exoplanets. Various types of masks could be employed to suppress the host star light to about 10-9 level contrast over a broad spectrum to enable the coronagraph mission objectives. Such masks for high contrast internal coronagraphic imaging require various fabrication technologies to meet a wide range of specifications, including precise shapes, micron scale island features, ultra-low reflectivity regions, uniformity, wave front quality, achromaticity, etc. We present the approaches employed at JPL to produce pupil plane and image plane coronagraph masks by combining electron beam, deep reactive ion etching, and black silicon technologies with illustrative examples of each, highlighting milestone accomplishments from the High Contrast Imaging Testbed (HCIT) at JPL and from the High Contrast Imaging Lab (HCIL) at Princeton University. We also present briefly the technologies applied to fabricate laboratory scale star shade masks.

GeV-scale dark matter: Production at the main injector

DOE PAGES

Dobrescu, Bogdan A.; Frugiuele, Claudia

2015-02-03

In this study, assuming that dark matter particles interact with quarks via a GeV-scale mediator, we study dark matter production in fixed target collisions. The ensuing signal in a neutrino near detector consists of neutral-current events with an energy distribution peaked at higher values than the neutrino background. We find that for a Z' boson of mass around a few GeV that decays to dark matter particles, the dark matter beam produced by the Main Injector at Fermilab allows the exploration of a range of values for the gauge coupling that currently satisfy all experimental constraints. The NOνA near detectormore » is well positioned for probing the presence of a dark matter beam, and future LBNF near detectors would provide more sensitive probes.« less

Does gender and experience influence shade matching quality?

PubMed

Haddad, Helene J; Jakstat, Holger A; Arnetzl, Gerwin; Borbely, Judit; Vichi, Alessandro; Dumfahrt, Herbert; Renault, Patrick; Corcodel, Nicoleta; Pohlen, Bostjan; Marada, Gyula; de Parga, Juan A Martinez Vazquez; Reshad, Mamaly; Klinke, Thomas U; Hannak, Wolfgang B; Paravina, Rade D

2009-01-01

To evaluate the influence of gender and level of experience on shade matching quality. A study was simultaneously performed at 15 universities located in 9 countries. A total of 614 color normal participants completed all phases of the experiment. Among them, there were 305 females and 309 males, 319 dental students and 295 dental professionals. A lecture on color matching in dentistry was given to all participants. Initial training was performed using Toothguide Trainer software (TT), while Toothguide Training Box (TTB) was used for both training and testing of participants' shade matching results. The test task was to successively match 15 shade guide tabs with the corresponding shade guide. The shade matching score for each participant was computed as a sum of color differences (SigmaDeltaE(ab)(*) score) between target tabs and selected tabs. Lower scores corresponded to better shade matching results and vice versa. Means and standard deviations were calculated. Mann-Whitney U test was used for statistical analysis of the data (alpha=0.05). The mean shade matching score (S.D.) for all participants was 41 (21). The score for female and male participants was 38 (20) and 44 (21), respectfully (p<0.001). The difference in scores between dental students, 42 (20), and dental professionals, 39 (21), was not statistically significant. Within the limitations of this study, females achieved significantly better shade matching results than males, indicating that gender plays an important role in shade matching. The level of experience was not found to be significant factor in shade matching.

Comparison of dark energy models after Planck 2015

NASA Astrophysics Data System (ADS)

Xu, Yue-Yao; Zhang, Xin

2016-11-01

We make a comparison for ten typical, popular dark energy models according to their capabilities of fitting the current observational data. The observational data we use in this work include the JLA sample of type Ia supernovae observation, the Planck 2015 distance priors of cosmic microwave background observation, the baryon acoustic oscillations measurements, and the direct measurement of the Hubble constant. Since the models have different numbers of parameters, in order to make a fair comparison, we employ the Akaike and Bayesian information criteria to assess the worth of the models. The analysis results show that, according to the capability of explaining observations, the cosmological constant model is still the best one among all the dark energy models. The generalized Chaplygin gas model, the constant w model, and the α dark energy model are worse than the cosmological constant model, but still are good models compared to others. The holographic dark energy model, the new generalized Chaplygin gas model, and the Chevalliear-Polarski-Linder model can still fit the current observations well, but from an economically feasible perspective, they are not so good. The new agegraphic dark energy model, the Dvali-Gabadadze-Porrati model, and the Ricci dark energy model are excluded by the current observations.

Assessment of the influence of gender and skin color on the preference of tooth shade in Saudi population.

PubMed

Labban, Nawaf; Al-Otaibi, Hanan; Alayed, Abdulaziz; Alshankiti, Khaled; Al-Enizy, Mohammad A

2017-07-01

The aim of the study was to evaluate the influence of gender and skin color on the preference of different teeth shades in general population. Two standardized frontal smile photographs of male and female subjects were manipulated using photoshop to represent 4 skin colors [(type II, III, IV, and V) (Fitzpatrick scale)]. The teeth shades under each skin color were digitally manipulated to represent one of 6 teeth shades (BL1, BL2, BL3, BL4, B1 and A1). A questionnaire assessed demographic characteristics (age, nationality, gender, education level, occupation, and income) along with the satisfaction of their smiles. Male and female set of pictures with combination of skin colors and teeth shades were presented and participants were asked to select the most esthetically pleasing teeth shade with regard to gender and skin color. Cross-tabulations and chi-squared tests were used to perform the statistical analyses ( α  = 0.05). Three hundred and thirty-six (60.4% male; 39.6% female) individuals participated in the study. The difference in the preferred teeth shades was significant among the male and female photographs across all skin colors ( p  < 0.05). Lighter teeth shades were preferred among female subjects compared to male subjects with the same skin color. In addition, lighter teeth shades were preferred among subjects with a lighter skin color and vice versa ( p  < 0.05). Gender and skin color influences the perception of teeth shades among general population. Therefore, lighter tooth shades (BL1, BL2) for lighter skin color and comparatively darker tooth shades (BL4, B1, A1) for darker skin individuals should be prescribed as these are perceived as natural among Saudi population.

Dark current suppression of MgZnO metal-semiconductor-metal solar-blind ultraviolet photodetector by asymmetric electrode structures.

PubMed

Wang, Ping; Zheng, Qinghong; Tang, Qing; Yang, Yintang; Guo, Lixin; Huang, Feng; Song, Zhenjie; Zhang, Zhiyong

2014-01-15

The application of asymmetric Schottky barrier and electrode area in an MgZnO metal-semiconductor-metal (MSM) solar-blind ultraviolet photodetector has been investigated by a physical-based numerical model in which the electron mobility is obtained by an ensemble Monte Carlo simulation combined with first principle calculations using the density functional theory. Compared with the experimental data of symmetric and asymmetric MSM structures based on ZnO substrate, the validity of this model is verified. The asymmetric Schottky barrier and electrode area devices exhibit reductions of 20 times and 1.3 times on dark current, respectively, without apparent photocurrent scarification. The plots of photo-to-dark current ratio (PDR) indicate that the asymmetric MgZnO MSM structure has better dark current characteristic than that of the symmetric one.

Using dark current data to estimate AVIRIS noise covariance and improve spectral analyses

NASA Technical Reports Server (NTRS)

Boardman, Joseph W.

1995-01-01

Starting in 1994, all AVIRIS data distributions include a new product useful for quantification and modeling of the noise in the reported radiance data. The 'postcal' file contains approximately 100 lines of dark current data collected at the end of each data acquisition run. In essence this is a regular spectral-image cube, with 614 samples, 100 lines and 224 channels, collected with a closed shutter. Since there is no incident radiance signal, the recorded DN measure only the DC signal level and the noise in the system. Similar dark current measurements, made at the end of each line are used, with a 100 line moving average, to remove the DC signal offset. Therefore, the pixel-by-pixel fluctuations about the mean of this dark current image provide an excellent model for the additive noise that is present in AVIRIS reported radiance data. The 61,400 dark current spectra can be used to calculate the noise levels in each channel and the noise covariance matrix. Both of these noise parameters should be used to improve spectral processing techniques. Some processing techniques, such as spectral curve fitting, will benefit from a robust estimate of the channel-dependent noise levels. Other techniques, such as automated unmixing and classification, will be improved by the stable and scene-independence noise covariance estimate. Future imaging spectrometry systems should have a similar ability to record dark current data, permitting this noise characterization and modeling.

Smart glass based on electrochromic polymers

NASA Astrophysics Data System (ADS)

Xu, Chunye; Kong, Xiangxing; Liu, Lu; Su, Fengyu; Kim, Sooyeun; Taya, Minoru

2006-03-01

Five-layer-structured electrochromic glass (window), containing a transparent conductive layer, an electrochromic layer, an ionic conductive layer, an ionic storage layer and a second conductive transparent layer, was fabricated. The electrochromic glass adopts the conjugated polymer, poly[3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine] (PProDOT-Me2), as a blue electrochromic active layer, vanadium pentaoxide film as an ion storage layer and polymer gel electrolyte as the ionic transport layer. Dimension of smart glass up to 12 x 20 inch was developed. UV curable sealant was applied for the sealing devices. Color changing or switching speed of 12 x 20 inch smart glass from dark state to the transparent state (or vise versa) is less than 15 seconds under applied 1.5 voltages. Besides the long open circuit memory (the colored state or transparent state remains the same state after the power is off), the smart window can be adjusted easily into the intermediate state between the dark state and the transparent state by just simply turn the power on or off. No space consuming or dirt collecting shades, curtains or blinds are needed. The applications of the smart window, e.g. in the aircrafts, automobiles and architectures were discussed as well.

Earth Observations taken by Expedition 38 crewmember

NASA Image and Video Library

2014-02-22

ISS038-E-057979 (22 Feb. 2014) --- This image, photographed by one of the Expedition 38 crew members aboard the International Space Station, shows the city of Green Bay, Wisconsin at the southern end of icebound Green Bay. This arm of Lake Michigan is six miles wide as seen in this view. The heavy snowfalls of the winter of 2014 cover the landscape. Combined with low sun illumination of a winter day, all surfaces appear as shades of gray. Fields appear brighter (top right, lower right), the cityscape (lower half of the image) appears as a checkerboard of grays, and forests (top left) appear dark. The center of the city lies on the Fox River, one of the few larger rivers in the United States that flow north. Open water appears as dark patches at the mouth of the river where a power station emits warm water. Thinner (grayer) ice can be detected where slightly warmer water extends from the river mouth towards Long Tail Point, an ancient shoreline of the bay. Crews aboard the space station do not usually take such detailed photographs because of the difficulty of getting sharp images with long lenses (in this case a 1000mm lens). Streets and bridges crossing the Fox River appear quite clearly.

Coral lipids and environmental stress.

PubMed

Harriott, V J

1993-04-01

Environmental monitoring of coral reefs is presently limited by difficulties in recognising coral stress, other than by monitoring coral mortality over time. A recent report described an experiment demonstrating that a measured lipid index declined in shaded corals. The technique described might have application in monitoring coral health, with a decline in coral lipid index as an indicator of coral stress. The application of the technique as a practical monitoring tool was tested for two coral species from the Great Barrier Reef. Consistent with the previous results, lipid index for Pocillopora damicornis initially declined over a period of three weeks in corals maintained in filtered seawater in the dark, indicating possible utilization of lipid stored as energy reserves. However, lipid index subsequently rose to near normal levels. In contrast, lipid index of Acropora formosa increased after four weeks in the dark in filtered seawater. The results showed considerable variability in lipid content between samples from the same colony. Results were also found to be dependent on fixation times and sample weight, introducing potential error into the practical application of the technique. The method as described would be unsuitable for monitoring environmental stress in corals, but the search for a practical method to monitor coral health should continue, given its importance in coral reef management.

[Effect of ceramic thickness and resin cement shades on final color of heat-pressed ceramic veneers].

PubMed

Ren, D F; Zhan, K R; Chen, X D; Xing, W Z

2017-02-09

Objective: To analyze the effect of ceramic materials thickness and resin cement shades on the final color of ceramic veneers in the discolored teeth, and to investigate the color agreement of try-in pastes to the corresponding resin cements. Methods: Sixty artificial maxillary central incisor teeth (C2 shade) were used to simulate the natural discolored teeth and prepared according to veneer tooth preparation protocol. Veneers of different thickness in the body region (0.50 and 0.75 mm) were fabricated using ceramic materials (LT A2 shade, IPS e.max Press). The ceramic veneer specimens were bonded to the artificial teeth using the 6 shades of resin cements (Variolink Veneer: shades of LV-3, LV-2, HV+3; RelyX™ Veneer: shades of TR, A3, WO) ( n= 5). A clinical spectrophotometer was used to measure the color parameters of ceramic veneers at the cervical, body and incisal regions. Color changes of veneers before and after cementation were calculated and registered as ΔE1, and the changes between try-in paste and the corresponding resin cements were registered as ΔE2. Results: Three-way ANOVA indicated that ΔE1 and ΔE2 values were significantly affected by the ceramic thickness, resin cement shades and measuring regions ( P< 0.05). The ΔE1 values of six shades ranged from 0.59-8.27. The ΔE1 values were more than 2.72 when the ceramic veneers were cemented with resin cements in shades of HV+3 and WO. The ΔE2 values of six shades ranged from 0.60-2.56. The shades of HV+3, WO and A3 resin cements were more than 1.60. Conclusions: Different thickness of ceramic materials, resin cement shades and measuring regions could affect the final color of ceramic veneers. The color differences of some resin cements and corresponding try-in pastes might be observed in clinical practice.

Lightness, chroma and hue differences on visual shade matching.

PubMed

Pecho, Oscar E; Pérez, María M; Ghinea, Razvan; Della Bona, Alvaro

2016-11-01

To analyze the influence of lightness, chroma and hue differences on visual shade matching performed by dental students. 100 dental students (DS) volunteers with normal vision participated in the study. A spectroradiometer (SP) was used to measure the spectral reflectance of 4 extracted human upper central incisors (UCI 1-4) and shade tabs from Vita Classical (VC) and Vita Toothguide 3D-Master (3D) shade guides. Measurements were performed over a gray background, inside a viewing booth and under D65 illuminant (diffuse/0° geometry). Color parameters (L*, a*, b*, C* and h°) were calculated. DS used VC and 3D to visually select the best shade match for each UCI. CIE metric differences (Δa * ,Δb * ,ΔL ' , ΔC ' and ΔH ' ) and CIEDE2000(2:1:1) lightness (ΔE L ), chroma (ΔE C ) and hue (ΔE H ) differences were obtained from each UCI and the first three shades selected by DS and the first option using CIELAB, CIEDE2000(1:1:1) and CIEDE2000(2:1:1) color difference metrics. The closest CIELAB color-discrimination ellipsoid (from RIT-DuPont visual color-difference data) to each UCI was selected for the analysis of visual shade matching. DS showed a preference for shades with lower chroma (ΔC ' and ΔE C ) and/or hue (ΔH ' and ΔE H ) values instead of shades with lower lightness values (ΔL ' and ΔE L ). Most best visual matches were near the tolerance ellipsoid centered on tooth shade. This study is an attempt to partially explain the inconsistencies between visual and instrumental shade matching and the limitations of shade guides. Visual shade matching was driven by color differences with lower chroma and hue values. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Influence of Different Enamel Shades and Thickness on Chroma and Value of Dentin Vita Shade: An in vitro Comparative Assessment Study.

PubMed

Hajira, Noor Saira Wajid Najma; Mehta, Deepak; Ashwini, P; Meena, N; Usha, H L

2015-04-01

The aim of the present study is to determine the influence of different enamel shades of various thickness on chroma and value of vita shade of dentin. Three enamel composite resin shades (Enamel white, grey and neutral) and one dentin shade (A 2) from A melogen Plus (Ultradent) was used. Ninety Enamel disk specimens of 0.5, 0.75 and 1 mm thickness and 10 mm in diameter for each shade and 90 dentin disk specimens of 2 mm in thickness and 10 mm in diameter was used for the study. The spectrophotometric values of the dentin shade with and without enamel specimens were recorded and the values were converted to CIEL*a*b values. Statistical analysis was done using Pearson correlation coefficients to verify the effect of thickness on Chroma and value, and the significance was evaluated by one-way ANOVA and Tukey post hoc test. Two way ANOVA and Tukey post hoc was done to verify the variation within the groups. Results revealed a significant positive correlation between thickness and chroma and a negative correlation between thickness and value. There was a statistically significant variation in between the groups. All groups produced a significant increase in chroma with increase in thickness of enamel shade upto a thickness of 0.75 mm after which the behavior of each shade was erratic. Hence, the optimum thickness would be 0.75 mm. All groups produced a significant decrease in value with increase in thickness of enamel shade. Enamel white produced the greatest reduction in value, enamel neutral the least and enamel grey demonstrated an intermediate result. There is a need to have a knowledge of the effect on chroma and value when dentin is layered with different enamel shades, it is also important to understand the effect of these enamel shades at different thicknesses to better control the color and reproduce esthetic simulating natural teeth.

[Studies on the shade-endurance capacity of Glycyrrhiza uralensis].

PubMed

Wei, Sheng-li; Wang, Wen-quan; Chen, Xiu-hua; Qin, Shu-ying; Chen, Xiu-tian

2005-01-01

To study the shade-endurance property of Glycyrrhiza uralensis and provide rationale for the practice of inter-cropping G. uralensis with trees. Black shading nets were used to provide five different environments of light intensities (light penetration rates of 100%, 75%, 65%, 50% and 25%, respectively). To assess the shade-endurance capacity of G. uralensis, several aspects were evaluated, including growth characters, physiological and ecological characters, biomass, and chemical contents. G. uralensis is a light-favored plant. The growth indices such as plant height, stem diameter, leaves number, root diameter, biomass, and daily average photosynthetic rate (Pn) are highest when light permeation rate is 100%. All these indices decrease when light intensity decreases. However, G. uralensis possesses shade-endurance capacity to some degree; it adapts to the shading environment by increasing the leaf area and chlorophyll contents. Shading has no obvious effect on the absolute light energy utilization rate (Eu) or Fv/Fm ratio. The influence of shading on the chemical contents of G. uralensis is obvious.

Environmental constraints on the invasion of Triadica sebifera in the eastern United States: an experimental field assessment.

PubMed

Pattison, Robert R; Mack, Richard N

2009-01-01

Identifying the environmental constraints that affect the distribution of an invasive species is fundamental to its effective control. Triadica sebifera (Chinese tallow tree) has invaded the southeastern United States, but its potential for further range and habitat extension has been unresolved. We explored experimentally environmental factors in macro- and microhabitats that affect its persistence at five widely separated sites along the Atlantic seaboard of the United States and at two sites inland; three sites occur well beyond the tree's current range. At each site, seeds and young vegetative plants (0.5-0.65 m tall) of T. sebifera were placed in four microhabitats (closed-canopy upland, closed-canopy lowland, open-canopy upland, and open-canopy lowland). Plant growth, leaf CO(2) assimilation rates, leaf N concentrations and delta(13)C ratios, and stem water potential were measured for two growing seasons. Percent seed germination was consistently higher in open-canopy microhabitats and lowest at northern and inland sites. T. sebifera grew in all open-canopy microhabitats, even 300-500 km beyond its current distribution. Plant growth in closed-canopy habitats was lower, attributable to lower carbon gain per unit leaf area in shaded compared with open-canopy environments, especially at northern and inland sites. Neither competition, other than canopy shade, nor grazing was a key constraint on distribution at any scale. Our results demonstrate that T. sebifera is dispersal limited at landscape scales but limited locally by dispersal and overstory shade; it has yet to occupy the full extent of its new range in North America. Quantifying environmental factors both within and well beyond a species' current range can effectively highlight the limits on its distribution.

Effects of Electrostatic Environment on Charged Particle Transport near Lunar Holes

NASA Astrophysics Data System (ADS)

Miyake, Y.; Nishino, M. N.

2017-12-01

The Moon has neither dense atmosphere nor intrinsic magnetic field, and solar wind interactions with lunar surfaces are one of major plasma processes. The near-surface, dayside electrostatic environment is governed mainly by volume charges of solar wind plasma and photoelectrons as well as charged lunar surfaces. In fact, the electric environment strongly depends on surface topologies, as it will produce a shaded region, the electric environment of which can be very different from that in a sunlit condition. As one of high-profile terrains on the Moon, we have been focusing on the lunar vertical holes (or lunar pits), identified by the KAGUYA satellite and the Lunar Reconnaissance Orbiter. In order to model the distinctive electric and dust environments near the holes, we have started three-dimensional particle simulation analysis. The present study addresses the plasma environment of a lunar hole that is accompanied with a subsurface cavern. Besides the topographical effect of having a cavern, an investigation is focused on the following points. The first point is how deeply the solar wind protons are accessible into the hole and cavern. This point is relevant not only to an electric environment but also to possible existence of volatiles at permanently shaded regions of the hole. In order to examine the possibility, we implemented a proton scattering process at lunar surfaces into the simulation model. The other is the role of some minor current components such as secondary electrons, scattered protons, and charged dust grains at the lunar surface. Such minor currents become important for the charging of shaded surfaces, as major current components (solar wind plasma and photoelectrons) are not accessible there. We address these points based on kinetic model descriptions.

Polar Lunar Regions: Exploiting Natural and Augmented Thermal Environments

NASA Astrophysics Data System (ADS)

Ryan, R. E.; McKellip, R. C.; Brannon, D. P.; Underwood, L. W.; Russell, K. J.

2007-12-01

In polar regions of the Moon, there are areas within craters that are permanently shadowed from solar illumination, which can reach temperatures of 100K or less. These regions could serve as cold traps, capturing ice and other volatile compounds. These potential ice stores have many applications for lunar exploration. Within double-shaded craters, even colder regions exist, with temperatures never exceeding 50K in many cases. Temperatures observed in theses regions suggest that they could enable equivalent liquid nitrogen cryogenic functions. These permanently shaded polar craters also offer unprecedented high vacuum cryogenic environments, which in their current state could support cryogenic applications. The unique conditions at the lunar poles, besides ice stores, harbor an environment that provides an opportunity to reduce the power, weight and total mass that needs to be carried from the Earth to the moon for lunar exploration and research. Reducing the heat flux of geothermal, black body radiation can have significant impacts on the achievable temperature. With a few man-made augmentations, permanently shaded craters located near the lunar poles achieve temperatures even lower than those that naturally exist there. Our analysis reveals that lightweight thermal shielding, within shaded craters, could create an environment several Kelvin above absolute zero. The temperature ranges of naturally shaded craters and thermally augmented ones could enable the long-term storage of most gases, low temperature superconductors for large magnetic fields, devices and advanced high speed computing instruments. Augmenting thermal conditions in these craters could then be used as a basis for the development of an advanced thermal management architecture that would support a wide variety of cryogenically based applications. Lunar exploration and habitation capabilities would significantly benefit if permanently shaded craters, augmented with thermal shielding, were to be used to facilitate the operation of near absolute zero instruments, including wide variety of cryogenically based propulsion, energy, communication, sensing and computing devices. Potentially, the required burden of carrying massive life-supporting components from the Earth to the moon for lunar exploration and research could be reduced.

[Study on the matching of the shade between beverage and modifying porcelain shade guide].

PubMed

Yao, Jiang-wu; Li, Shui-gen; Lin, Jin-ying

2007-10-01

To evaluate the matching of the shade between beverage and modifying porcelain shade guide according to Munsell color order system, thus to provide the reference basis for selecting modifying porcelain to mimic the stain of natural tooth by technician. The shade of Vita Akzent, Vita Interno, Shofu Vintage & Unibond and Noritake Super Porcelain EX-3 shade tabs as well as 15 kinds of beverage were measured according to Munsell color order system on Color-Eye 7000A spectrophotometer. The difference of the frequency of approximate hue, value, and chroma between shade tabs and beverage were compared by calculating the Fisher exact probabilities. The frequency of approximate hue between 4 kinds of shade tabs and 15 kinds of bev-erage was significant different (P<0.05), while the frequency of approximate value, and chroma was not significant different (P>0.05). Except the hue, the color distribution of 4 kinds of shade tabs was similar to that of 15 kinds of beverage. But the color of beverage also can be approximately matched by any kind of modifying porcelain by mixing porcelain powder of appropriate hue, value, and chroma.

Color reproduction for advanced manufacture of soft tissue prostheses.

PubMed

Xiao, Kaida; Zardawi, Faraedon; van Noort, Richard; Yates, Julian M

2013-11-01

The objectives of this study were to develop a color reproduction system in advanced manufacture technology for accurate and automatic processing of soft tissue prostheses. The manufacturing protocol was defined to effectively and consistently produce soft tissue prostheses using a 3D printing system. Within this protocol printer color profiles were developed using a number of mathematical models for the proposed 3D color printing system based on 240 training colors. On this basis, the color reproduction system was established and their system errors including accuracy of color reproduction, performance of color repeatability and color gamut were evaluated using 14 known human skin shades. The printer color profile developed using the third-order polynomial regression based on least-square fitting provided the best model performance. The results demonstrated that by using the proposed color reproduction system, 14 different skin colors could be reproduced and excellent color reproduction performance achieved. Evaluation of the system's color repeatability revealed a demonstrable system error and this highlighted the need for regular evaluation. The color gamut for the proposed 3D printing system was simulated and it was demonstrated that the vast majority of skin colors can be reproduced with the exception of extreme dark or light skin color shades. This study demonstrated that the proposed color reproduction system can be effectively used to reproduce a range of human skin colors for application in advanced manufacture of soft tissue prostheses. Copyright © 2013 Elsevier Ltd. All rights reserved.

Spectral CT metal artifact reduction with an optimization-based reconstruction algorithm

NASA Astrophysics Data System (ADS)

Gilat Schmidt, Taly; Barber, Rina F.; Sidky, Emil Y.

2017-03-01

Metal objects cause artifacts in computed tomography (CT) images. This work investigated the feasibility of a spectral CT method to reduce metal artifacts. Spectral CT acquisition combined with optimization-based reconstruction is proposed to reduce artifacts by modeling the physical effects that cause metal artifacts and by providing the flexibility to selectively remove corrupted spectral measurements in the spectral-sinogram space. The proposed Constrained `One-Step' Spectral CT Image Reconstruction (cOSSCIR) algorithm directly estimates the basis material maps while enforcing convex constraints. The incorporation of constraints on the reconstructed basis material maps is expected to mitigate undersampling effects that occur when corrupted data is excluded from reconstruction. The feasibility of the cOSSCIR algorithm to reduce metal artifacts was investigated through simulations of a pelvis phantom. The cOSSCIR algorithm was investigated with and without the use of a third basis material representing metal. The effects of excluding data corrupted by metal were also investigated. The results demonstrated that the proposed cOSSCIR algorithm reduced metal artifacts and improved CT number accuracy. For example, CT number error in a bright shading artifact region was reduced from 403 HU in the reference filtered backprojection reconstruction to 33 HU using the proposed algorithm in simulation. In the dark shading regions, the error was reduced from 1141 HU to 25 HU. Of the investigated approaches, decomposing the data into three basis material maps and excluding the corrupted data demonstrated the greatest reduction in metal artifacts.

Pixelated Geiger-Mode Avalanche Photo-Diode Characterization Through Dark Current Measurement

NASA Astrophysics Data System (ADS)

Amaudruz, Pierre-Andre; Bishop, Daryl; Gilhully, Colleen; Goertzen, Andrew; James, Lloyd; Kozlowski, Piotr; Retiere, Fabrice; Shams, Ehsan; Sossi, Vesna; Stortz, Greg; Thiessen, Jonathan D.; Thompson, Christopher J.

2014-06-01

PIXELATED geiger-mode avalanche photodiodes (PPDs), often called silicon photomultipliers (SiPMs) are emerging as an excellent replacement for traditional photomultiplier tubes (PMTs) in a variety of detectors, especially those for subatomic physics experiments, which requires extensive test and operation procedures in order to achieve uniform responses from all the devices. In this paper, we show for two PPD brands, Hamamatsu MPPC and SensL SPM, that at room temperature, the dark noise rate, breakdown voltage and rate of correlated avalanches can be inferred from the sole measure of dark current as a function of operating voltage, hence greatly simplifying the characterization procedure. We introduce a custom electronics system that allows measurement for many devices concurrently, hence allowing rapid testing and monitoring of many devices at low cost. Finally, we show that the dark current of Hamamastu Multi-Pixel Photon Counter (MPPC) is rather independent of temperature at constant operating voltage, hence the current measure cannot be used to probe temperature variations. On the other hand, the MPPC current can be used to monitor light source conditions in DC mode without requiring strong temperature stability, as long as the integrated source brightness is comparable to the dark noise rate.

Performance Simulation of Unipolar InAs/InAs1-x Sb x Type-II Superlattice Photodetector

NASA Astrophysics Data System (ADS)

Singh, Anand; Pal, Ravinder

2018-05-01

This paper reports performance simulation of a unipolar tunable band gap InAs-InAsSb type-II superlattice (T2SL) infrared photodetector. The generation-recombination and surface leakage currents limit the performance of T2SL photodiodes. Unipolar nBn device design incorporating a suitable barrier layer in the diode structure is taken to suppress the Auger recombination and tunneling currents. At low reverse bias, the generation-recombination current is negligible in the absence of a depletion region, but the dark current is dominated by the diffusion current at higher operation temperatures. The composition, band alignment, barrier width, doping level and thickness of the absorber region are optimized here to achieve low dark current and high quantum efficiency at elevated operating temperatures. Thin unipolar T2SL absorbers are placed in a resonant cavity to enhance photon-material interaction, thus allowing complete absorption in a thinner detector element. It leads to the reduction in the detector volume for lower dark current without affecting the quantum efficiency. It shows an improvement in the quantum efficiency and reduction in the dark current. Dark current density ˜ 10-5 A/cm2 is achievable with low absorber thickness of 2 μm and effective lifetime of 250 ns in the InAs/InAs0.6Sb0.4/B-AlAs1-x Sb x long wave length T2SL detector at 110 K.

Dark Signal Characterization of 1.7 micron cutoff devices for SNAP

NASA Astrophysics Data System (ADS)

Smith, R. M.; SNAP Collaboration

2004-12-01

We report initial progress characterizing non-photometric sources of error -- dark current, noise, and zero point drift -- for 1.7 micron cutoff HgCdTe and InGaAs detectors under development by Raytheon, Rockwell, and Sensors Unlimited for SNAP. Dark current specifications can already be met with several detector types. Changes to the manufacturing process are being explored to improve the noise reduction available through multiple sampling. In some cases, a significant number of pixels suffer from popcorn noise, with a few percent of all pixels exhibiting a ten fold noise increase. A careful study of zero point drifts is also under way, since these errors can dominate dark current, and may contribute to the noise degradation seen in long exposures.

Electronic transport in a long wavelength infrared quantum cascade detector under dark condition

NASA Astrophysics Data System (ADS)

Li, L.; Zhou, X. H.; Lin, T.; Li, N.; Zhu, Z. Q.; Liu, F. Q.

2016-09-01

We present a joint experimental and theoretical investigation on a long wavelength infrared quantum cascade detector to reveal its dark current paths. The temperature dependence of the dark current is measured. It is shown that there are two different transport mechanisms, namely resonant tunneling at low temperatures and thermal excitation at higher temperature, dominate the carrier flow, respectively. Moreover, the experimental intersubband transition energies obtained by the magneto-transport measurements matches the theoretical predictions well. With the aid of the calculated band structures, we can explain the observed oscillation phenomena of the dark current under the magnetic field very well. The obtained results provide insight into the transport properties of quantum cascade detectors thus providing a useful tool for device optimization.

External shading devices for energy efficient building

NASA Astrophysics Data System (ADS)

Shahdan, M. S.; Ahmad, S. S.; Hussin, M. A.

2018-02-01

External shading devices on a building façade is an important passive design strategy as they reduce solar radiation. Although studies have proven the benefits of external shading devices, many are designed solely for aesthetic purposes without fully considering its high potential to reduce solar radiation and glare. Furthermore, explorations into shading devices by the design team are mostly left too late in the design development phases. Hence, the paper looks into the effectiveness of external shading devices on a building towards more energy efficient building. The study aims to analyse the effects of various configurations of external shading devices towards the energy consumption of a case study building based on computer simulations. This study uses Building Information Modelling (BIM) through Autodesk Revit software as simulation tool. The constant variables for the simulation are the orientation of the building, types of glazing used by the building and the internal loads of the building. Whereas, the manipulated variable is the types of shading device used. The data were sorted according to the categories and translated into a chart. Analysis of the findings indicate that shading devices with different configurations show significant results in the energy consumption and the best configuration is the egg-crate shading devices. The study recommends that the consideration for shading device as a passive design strategy needs to be developed at the early stage of the building design.

An experimental and theoretical study of the dark current and x-ray sensitivity of amorphous selenium x-ray photoconductors

NASA Astrophysics Data System (ADS)

Frey, Joel Brandon

Recently, the world of diagnostic radiography has seen the integration of digital flat panel x-ray image detectors into x-ray imaging systems, replacing analog film screens. These flat panel x-ray imagers (FPXIs) have been shown to produce high quality x-ray images and provide many advantages that are inherent to a fully digital technology. Direct conversion FPXIs based on a photoconductive layer of stabilized amorphous selenium (a-Se) have been commercialized and have proven particularly effective in the field of mammography. In the operation of these detectors, incident x-ray photons are converted directly to charge carriers in the a-Se layer and drifted to electrodes on either side of the layer by a large applied field (10 V/microm). The applied field causes a dark current to flow which is not due to the incident radiation and this becomes a source of noise which can reduce the dynamic range of the detector. The level of dark current in commercialized detectors has been reduced by the deposition of thin n- and p- type blocking layers between the electrodes and the bulk of the a-Se. Despite recent research into the dark current in metal/a-Se/metal sandwich structures, much is still unknown about the true cause and nature of this phenomenon. The work in this Ph.D. thesis describes an experimental and theoretical study of the dark current in these structures. Experiments have been performed on five separate sets of a-Se samples which approximate the photoconductive layer in an FPXI. The dark current has been measured as a function of time, sample structure, applied field, sample thickness and contact metal used. This work has conclusively shown that the dark current is almost entirely due to the injection of charge carriers from the contacts and the contribution of Poole-Frenkel enhanced bulk thermal generation is negligible. There is also evidence that while the dark current is initially controlled by the injection of holes from the positive contact, several minutes after the application of the bias, the dark current due to hole injection may decay to the point where the electron current becomes significant and even dominant. These conclusions are supported by numerical calculations of the dark current transients which have been calibrated to match experimental results. Work detailed in this Ph.D. thesis also focuses on Monte Carlo modeling of the x-ray sensitivity of a-Se FPXIs. The higher the x-ray sensitivity of a detector, the lower the radiation dose required to acquire an acceptable image. FPXIs can experience a decrease in the x-ray sensitivity of the photoconductive layer with accumulating exposure, leading to a phenomenon known as "ghosting". Modeling this decrease in sensitivity can uncover the reasons behind it. The Monte Carlo model described in this thesis is a continuation of a previous model which now considers the effects of the n- and p-like blocking layers and the flow of dark current between x-ray exposures. The simulation results explain how deep trapping of photogenerated charge carriers, and the resulting effect on the electric field distribution, contribute to sensitivity loss. The model has shown excellent agreement with experimental data and has accurately predicted a sensitivity recovery once exposure has ceased which is due to primarily to the relaxation of metastable x-ray-induced carrier trap states.

Relationship between natural tooth shade and skin colour.

PubMed

Nourbakhsh, M; Mousavinejad, N; Adli, A R; Harati, M

2013-06-01

The purpose of this study was to assess the correlation of skin colour and tooth shade. One hundred and twenty six individuals aging between 18 to 25 years participated in this study. Colour of the maxillary central incisors was examined by VITA easy shade. Tooth shades were assigned to four ordinal values. Nivea Beauty Protect Foundation shade sample was used as a guide to assess facial skin colour Shin colours were also assigned to four ordinal values. Spearman test revealed that there was a significant relationship between tooth shade and skin colour Total co-relation factor was 51.6% (p <0 .01). Co-relation factors were 57% for women and 27% for men (p <0 .01). The highest tooth shade prevalence belonged to the second group and the highest skin colour prevalence was also in the second skin colour group.

Hubble Chases a Small Stellar Galaxy in the Hunting Dog

NASA Image and Video Library

2017-12-08

On a clear evening in April of 1789, the renowned astronomer William Herschel continued his unrelenting survey of the night sky, hunting for new cosmic objects — and found cause to celebrate! He spotted this bright spiral galaxy, named NGC 4707, lurking in the constellation of Canes Venatici or The Hunting Dog. NGC 4707 lies roughly 22 million light-years from Earth. Over two centuries later, the NASA/ESA Hubble Space Telescope is able to "chase down" and view the same galaxy in far greater detail than Herschel could, allowing us to appreciate the intricacies and characteristics of NGC 4707 as never before. This striking image comprises observations from Hubble’s Advanced Camera for Surveys (ACS), one of a handful of high-resolution instruments currently aboard the space telescope. Herschel himself reportedly described NGC 4707 as a “small, stellar” galaxy; while it is classified as a spiral (type Sm), its overall shape, center, and spiral arms are very loose and undefined, and its central bulge is either very small or non-existent. It instead appears as a rough sprinkling of stars and bright flashes of blue on a dark canvas. The blue smudges seen across the frame highlight regions of recent or ongoing star formation, with newborn stars glowing in bright, intense shades of cyan and turquoise. Image credit: ESA/Hubble & NASA

Using Google Earth to Assess Shade for Sun Protection in Urban Recreation Spaces: Methods and Results.

PubMed

Gage, R; Wilson, N; Signal, L; Barr, M; Mackay, C; Reeder, A; Thomson, G

2018-05-16

Shade in public spaces can lower the risk of and sun burning and skin cancer. However, existing methods of auditing shade require travel between sites, and sunny weather conditions. This study aimed to evaluate the feasibility of free computer software-Google Earth-for assessing shade in urban open spaces. A shade projection method was developed that uses Google Earth street view and aerial images to estimate shade at solar noon on the summer solstice, irrespective of the date of image capture. Three researchers used the method to separately estimate shade cover over pre-defined activity areas in a sample of 45 New Zealand urban open spaces, including 24 playgrounds, 12 beaches and 9 outdoor pools. Outcome measures included method accuracy (assessed by comparison with a subsample of field observations of 10 of the settings) and inter-rater reliability. Of the 164 activity areas identified in the 45 settings, most (83%) had no shade cover. The method identified most activity areas in playgrounds (85%) and beaches (93%) and was accurate for assessing shade over these areas (predictive values of 100%). Only 8% of activity areas at outdoor pools were identified, due to a lack of street view images. Reliability for shade cover estimates was excellent (intraclass correlation coefficient of 0.97, 95% CI 0.97-0.98). Google Earth appears to be a reasonably accurate and reliable and shade audit tool for playgrounds and beaches. The findings are relevant for programmes focused on supporting the development of healthy urban open spaces.

Reliability of conventional shade guides in teeth color determination.

PubMed

Todorović, Ana; Todorović, Aleksandar; Gostović, Aleksandra Spadijer; Lazić, Vojkan; Milicić, Biljana; Djurisić, Slobodan

2013-10-01

Color matching in prosthodontic therapy is a very important task because it influences the esthetic value of dental restorations. Visual shade matching represents the most frequently applied method in clinical practice. Instrumental measurements provide objective and quantified data in color assessment of natural teeth and restorations. In instrumental shade analysis, the goal is to achieve the smallest deltaE value possible, indicating the most accurate shade match. The aim of this study was to evaluate the reliability of commercially available ceramic shade guides. VITA Easyshade spectrophotometer (VITA, Germany) was used for instrumental color determination. Utilizing this device, color samples of ten VITA Classical and ten VITA 3D - Master shade guides were analyzed. Each color sample from all shade guides was measured three times and the basic parameters of color quality were examined: deltaL, deltaC, deltaH, deltaE, deltaElc. Based on these parameters spectrophotometer marks the shade matching as good, fair or adjust. After performing 1,248 measurements of ceramic color samples, frequency of evaluations adjust, fair and good were statistically significantly different between VITA Classical and VITA 3D Master shade guides (p = 0.002). There were 27.1% cases scored as adjust, 66.3% as fair and 6.7% as good. In VITA 3D - Master shade guides 30.9% cases were evaluated as adjust, 66.4% as fair and 2.7% cases as good. Color samples from different shade guides, produced by the same manufacturer, show variability in basic color parameters, which once again proves the lack of precision and nonuniformity of the conventional method.

Measured and estimated performance of a fleet of shaded photovoltaic systems with string and module-level inverters

DOE PAGES

MacAlpine, Sara; Deline, Chris; Dobos, Aron

2017-03-16

Shade obstructions can significantly impact the performance of photovoltaic (PV) systems. Although there are many models for partially shaded PV arrays, there is a lack of information available regarding their accuracy and uncertainty when compared with actual field performance. This work assesses the recorded performance of 46 residential PV systems, equipped with either string-level or module-level inverters, under a variety of shading conditions. We compare their energy production data to annual PV performance predictions, with a focus on the practical models developed here for National Renewable Energy Laboratory's system advisor model software. This includes assessment of shade extent on eachmore » PV system by using traditional onsite surveys and newer 3D obstruction modelling. The electrical impact of shade is modelled by either a nonlinear performance model or assumption of linear impact with shade extent, depending on the inverter type. When applied to the fleet of residential PV systems, performance is predicted with median annual bias errors of 2.5% or less, for systems with up to 20% estimated shading loss. The partial shade models are not found to add appreciable uncertainty to annual predictions of energy production for this fleet of systems but do introduce a monthly root-mean-square error of approximately 4%-9% due to seasonal effects. Here the use of a detailed 3D model results in similar or improved accuracy over site survey methods, indicating that, with proper description of shade obstructions, modelling of partially shaded PV arrays can be done completely remotely, potentially saving time and cost.« less

Detecting Subtle Shifts in Ecosystem Functioning in a Dynamic Estuarine Environment

PubMed Central

Pratt, Daniel R.; Lohrer, Andrew M.; Thrush, Simon F.; Hewitt, Judi E.; Townsend, Michael; Cartner, Katie; Pilditch, Conrad A.; Harris, Rachel J.; van Colen, Carl; Rodil, Iván F.

2015-01-01

Identifying the effects of stressors before they impact ecosystem functioning can be challenging in dynamic, heterogeneous ‘real-world’ ecosystems. In aquatic systems, for example, reductions in water clarity can limit the light available for photosynthesis, with knock-on consequences for secondary consumers, though in naturally turbid wave-swept estuaries, detecting the effects of elevated turbidity can be difficult. The objective of this study was to investigate the effects of shading on ecosystem functions mediated by sandflat primary producers (microphytobenthos) and deep-dwelling surface-feeding macrofauna (Macomona liliana; Bivalvia, Veneroida, Tellinidae). Shade cloths (which reduced incident light intensity by ~80%) were deployed on an exposed, intertidal sandflat to experimentally stress the microphytobenthic community associated with the sediment surface. After 13 weeks, sediment properties, macrofauna and fluxes of oxygen and inorganic nutrients across the sediment-water interface were measured. A multivariate metric of ecosystem function (MF) was generated by combining flux-based response variables, and distance-based linear models were used to determine shifts in the drivers of ecosystem function between non-shaded and shaded plots. No significant differences in MF or in the constituent ecosystem function variables were detected between the shaded and non-shaded plots. However, shading reduced the total explained variation in MF (from 64% in non-shaded plots to 15% in shaded plots) and affected the relative influence of M. liliana and other explanatory variables on MF. This suggests that although shade stress may shift the drivers of ecosystem functioning (consistent with earlier investigations of shading effects on sandflat interaction networks), ecosystem functions appear to have a degree of resilience to those changes. PMID:26214854

Shaded Relief and Radar Image with Color as Height, Madrid, Spain

NASA Technical Reports Server (NTRS)

2002-01-01

The white, mottled area in the right-center of this image from NASA's Shuttle Radar Topography Mission (SRTM) is Madrid, the capital of Spain. Located on the Meseta Central, a vast plateau covering about 40 percent of the country, this city of 3 million is very near the exact geographic center of the Iberian Peninsula. The Meseta is rimmed by mountains and slopes gently to the west and to the series of rivers that form the boundary with Portugal. The plateau is mostly covered with dry grasslands, olive groves and forested hills.

Madrid is situated in the middle of the Meseta, and at an elevation of 646 meters (2,119 feet) above sea level is the highest capital city in Europe. To the northwest of Madrid, and visible in the upper left of the image, is the Sistema Central mountain chain that forms the 'dorsal spine' of the Meseta and divides it into northern and southern subregions. Rising to about 2,500 meters (8,200 feet), these mountains display some glacial features and are snow-capped for most of the year. Offering almost year-round winter sports, the mountains are also important to the climate of Madrid.

Three visualization methods were combined to produce this image: shading and color coding of topographic height and radar image intensity. The shade image was derived by computing topographic slope in the northwest-southeast direction. North-facing slopes appear bright and south-facing slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and brown to white at the highest elevations. The shade image was combined with the radar intensity image in the flat areas.

Elevation data used in this image was acquired by the SRTM aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 172 by 138 kilometers (107 by 86 miles) Location: 40.43 degrees North latitude, 3.70 degrees West longitude Orientation: North toward the top Image Data: shaded and colored SRTM elevation model, with SRTM radar intensity added Original Data Resolution: SRTM 1 arcsecond (about 30 meters or 98 feet) Date Acquired: February 2000

NICMOS Temperature-specific Darks

NASA Astrophysics Data System (ADS)

Monroe, B.; Bergeron, E.

1999-11-01

The various components of NICMOS dark images have been modeled and combined to make synthetic dark calibration files which are intended for use with observations in a temperature range from 61 to ~75 K, currently available only for camera 2, with cameras 1 and 3 to follow in a few months. The amplifier glow and the true linear dark current have been constructed as temperature-independent quantities, while the “shading” component of the darks has been modeled as temperature-dependent. The data used to construct these models was taken with NIC 2, in a temperature range of 61 to 80 K during the recent warm-up of NICMOS due to cryogen exhaustion. The resulting synthetic darks are available through a web-based tool on the STScI NICMOS website http://www.stsci.edu/instruments/nicmos/NICMOS_tools/syndark.html.

A novel two-step method for screening shade tolerant mutant plants via dwarfism

USDA-ARS?s Scientific Manuscript database

When subjected to shade, plants undergo rapid shoot elongation, which often makes them more prone to disease and mechanical damage. It has been reported that, in turfgrass, induced dwarfism can enhance shade tolerance. Here, we describe a two-step procedure for isolating shade tolerant mutants of ...

Retractable Sun Shade

NASA Technical Reports Server (NTRS)

Frank, A.; Derespinis, S. F.; Mockovciak, John, Jr.

1986-01-01

Window-shade type spring roller contains blanket, taken up by rotating cylindrical frame and held by frame over area to be shaded. Blanket made of tough, opaque polyimide material. Readily unfurled by mechanism to protect space it encloses from Sun. Blanket forms arched canopy over space and allows full access to it from below. When shading not needed, retracted mechanism stores blanket compactly. Developed for protecting sensitive Space Shuttle payloads from direct sunlight while cargo-bay doors open. Adapted to shading of greenhouses, swimming pools, and boats.

Aerosol Optical Depth Retrievals From High-Resolution Commercial Satellite Imagery Over Areas of High Surface Reflectance

NASA Astrophysics Data System (ADS)

Vincent, D. A.; Nielsen, K. E.; Durkee, P. A.; Reid, J. S.

2005-12-01

The advancement and proliferation of high-resolution commercial imaging satellites presents a new opportunity for overland aerosol characterization. Current aerosol optical depth retrieval methods typically fail over areas with high surface reflectance, such as urban areas and deserts, since the upwelling radiance due to scattering by aerosols is small compared to the radiance resulting from surface reflection. The method proposed here uses shadows cast on the surface to exploit the differences between radiance from the adjacent shaded and unshaded areas of the scene. Shaded areas of the scene are primarily illuminated by diffuse irradiance that is scattered downward from the atmosphere, while unshaded areas are illuminated by both diffuse and direct solar irradiance. The first-order difference between the shaded and unshaded areas is the direct component. Given uniform surface reflectance for the shaded and unshaded areas, the difference in reflected radiance measured by a satellite sensor is related to the direct transmission of solar radiation and inversely proportional to total optical depth. Using an iterative approach, surface reflectance and mean aerosol reflectance can be partitioned to refine the retrieved total optical depth. Aerosol optical depth can then be determined from its contribution to the total atmospheric optical depth (following correction for molecular Rayleigh scattering). Intitial results based on QuickBird imagery and AERONET data collected during the United Arab Emirates Unified Aerosol Experiment (UAE2) indicate that aerosol optical depth retrievals are possible in the visible and near-infrared region with an accuracy of ~0.04.

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials

PubMed Central

2018-01-01

PURPOSE The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TPSCI), surface gloss (ΔE*SCE-SCI), and surface roughness (Ra) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)]. MATERIALS AND METHODS The specimens (N = 225) were prepared into square-shaped (12 × 12 mm2) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry. RESULTS Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness (P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TPSCI results demonstrated a significant difference in terms of material types and material thicknesses (P ≤ .001). TPSCI values of the tested materials were ordered as LU > CS > VE. ΔE*SCE-SCI and Ra results were significantly varied amongst the materials (P < .001) and amongst the shades (P < .05). The order of ΔE*SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of Ra was CS ≥ VE > LU. CONCLUSION Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters. PMID:29503712

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials.

PubMed

Egilmez, Ferhan; Ergun, Gulfem; Cekic-Nagas, Isil; Vallittu, Pekka Kalevi; Lassila, Lippo Veli Juhana

2018-02-01

The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TP SCI ), surface gloss (ΔE * SCE-SCI ), and surface roughness (R a ) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)]. The specimens (N = 225) were prepared into square-shaped (12 × 12 mm 2 ) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry. Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness ( P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TP SCI results demonstrated a significant difference in terms of material types and material thicknesses ( P ≤ .001). TP SCI values of the tested materials were ordered as LU > CS > VE. ΔE * SCE-SCI and R a results were significantly varied amongst the materials ( P < .001) and amongst the shades ( P < .05). The order of ΔE * SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of R a was CS ≥ VE > LU. Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters.

Thermal and Electrical Effects of Partial Shade in Monolithic Thin-Film Photovoltaic Modules: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silverman, Timothy J.; Deceglie, Michael G.; Sun, Xingshu

2015-09-02

Photovoltaic cells can be damaged by reverse bias stress, which arises during service when a monolithically integrated thin-film module is partially shaded. We introduce a model for describing a module's internal thermal and electrical state, which cannot normally be measured. Using this model and experimental measurements, we present several results with relevance for reliability testing and module engineering: Modules with a small breakdown voltage experience less stress than those with a large breakdown voltage, with some exceptions for modules having light-enhanced reverse breakdown. Masks leaving a small part of the masked cells illuminated can lead to very high temperature andmore » current density compared to masks covering entire cells.« less

Thermal and Electrical Effects of Partial Shade in Monolithic Thin-Film Photovoltaic Modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silverman, Timothy J.; Deceglie, Michael G.; Sun, Xingshu

2015-06-14

Photovoltaic cells can be damaged by reverse bias stress, which arises during service when a monolithically integrated thin-film module is partially shaded. We introduce a model for describing a module's internal thermal and electrical state, which cannot normally be measured. Using this model and experimental measurements, we present several results with relevance for reliability testing and module engineering: Modules with a small breakdown voltage experience less stress than those with a large breakdown voltage, with some exceptions for modules having light-enhanced reverse breakdown. Masks leaving a small part of the masked cells illuminated can lead to very high temperature andmore » current density compared to masks covering entire cells.« less

Effects of 1- and 2-MeV electrons on photomultiplier tubes

NASA Technical Reports Server (NTRS)

Beatty, M. E., III; Debnam, W. J., Jr.; Meredith, B. D.

1976-01-01

Various types of photomultiplier tubes useful for space applications were irradiated with 1- and 2-MeV electrons at Van Allen radiation belt fluxes of 100,000 to 10 millions electrons/sq cm-sec. The increase in the dark current due to electron irradiation was observed at various bias voltages under worst-case conditions (no shielding). Results were presented in the form of dark current plotted against electron flux. All the tubes tested showed extremely large increases in dark current. Tube types 541A, 6217, 6199, and 6903 exhibited the largest increases under irradiation, whereas type 1P22 was affected the least. All the damage observed was transient. The luminescence produced in the optical window probably accounts for a large part of the dark-current increases, but there were some effects possibly due to direct irradiation of the photocathode and dynode chain.

Mts. Agung and Batur, Bali, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

This perspective view shows the major volcanic group of Bali, one 13,000 islands comprising the nation of Indonesia. The conical mountain to the left is Gunung Agung, at 3,148 meters (10,308 feet) the highest point on Bali and an object of great significance in Balinese religion and culture. Agung underwent a major eruption in 1963 after more than 100 years of dormancy, resulting in the loss of over 1,000 lives.

In the center is the complex structure of Batur volcano, showing a caldera (volcanic crater) left over from a massive catastrophic eruption about 30,000 years ago. Judging from the total volume of the outer crater and the volcano, that once lay above it, approximately 140 cubic kilometers(33.4 cubic miles) of material must have been produced by this eruption, making it one of the largest known volcanic events on Earth. Batur is still active and has erupted at least 22 times since the 1800's.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Location: 8.33 degrees South latitude, 115.17 degrees East longitude Orientation: Looking southwest Size: scale varies in this perspective image Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Shenandoah National Park, Virginia, Shaded Relief with Height as Color

NASA Technical Reports Server (NTRS)

2003-01-01

Shenandoah National Park lies astride part of the Blue Ridge Mountains, which form the southeastern range of the greater Appalachian Mountains in Virginia. The park is well framed by this one-degree of latitude (38-39 north) by one-degree of longitude (78-79 west) cell of Shuttle Radar Topography Mission data, and it appears here as the most prominent ridge trending diagonally across the scene. Skyline Drive, a 169-kilometer (105-mile) road that winds along the crest of the mountains through the length the park, provides vistas of the surrounding landscape. The Shenandoah River flows through the valley to the west, with Massanutten Mountain standing between the river's north and south forks. Unusually pronounced meanders of both river forks are very evident near the top center of this scene. Massanutten Mountain itself is an unusually distinctive landform also, consisting of highly elongated looping folds of sedimentary rock. The rolling Piedmont country lies to the southeast of the park, with Charlottesville located at the bottom center of the scene.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to bluish-white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on February 11, 2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar that flew twice on the Space Shuttle Endeavour in 1994. The Shuttle Radar Topography Mission was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, DC.

Size: 111 by 87 kilometers (69 by 54 miles) Location: 38-39 degrees North latitude, 78-79 degrees West longitude Orientation: North toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

SRTM Colored Height and Shaded Relief: Las Bayas, Argentina

NASA Technical Reports Server (NTRS)

2001-01-01

The interplay of volcanism, stream erosion and landslides is evident in this Shuttle Radar Topography Mission view of the eastern flank of the Andes Mountains, southeast of San Carlos de Bariloche, Argentina. Older lava flows emanating from the Andes once covered much of this area. Younger, local volcanoes (seen here as small peaks) then covered parts of the area with fresh, erosion resistant flows (seen here as very smooth surfaces). Subsequent erosion has created fine patterns on the older surfaces (bottom of the image) and bolder, irregular patterns through and around the younger surfaces (upper center and right center). Meanwhile, where a large stream immediately borders the resistant plateau (center of the image), lateral erosion has undercut the resistant plateau causing slivers of it to fall into the stream channel. This scene well illustrate show topographic data alone can reveal some aspects of recent geologic history.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark, as would be the case at noon at this latitude in the southern hemisphere. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on February 11, 2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar that flew twice on the Space Shuttle Endeavour in 1994. The Shuttle Radar Topography Mission was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Size: 54.3 x 36.4 kilometers ( 33.7 x 22.6 miles) Location: 41.4 deg. South lat., 70.8 deg. West lon. Orientation: North toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

SRTM Perspective of Colored Height and Shaded Relief Laguna Mellquina, Andes Mountains, Argentina

NASA Technical Reports Server (NTRS)

2001-01-01

This depiction of an area south of San Martin de Los Andes, Argentina, is the first Shuttle Radar Topography Mission (SRTM)view of the Andes Mountains, the tallest mountain chain in the western hemisphere. This particular site does not include the higher Andes peaks, but it does include steep-sided valleys and other distinctive landforms carved by Pleistocene glaciers. Elevations here range from about 700 to 2,440 meters (2,300 to 8,000 feet). This region is very active tectonically and volcanically, and the landforms provide a record of the changes that have occurred over many thousands of years. Large lakes fill the broad mountain valleys, and the spectacular scenery here makes this area a popular resort destination for Argentinians.

Three visualization methods were combined to produce this image: shading, color coding of topographic height and a perspective view. The shade image was derived by computing topographic slope in the north-south direction. Northern slopes appear bright and southern slopes appear dark, as would be the case at noon at this latitude in the southern hemisphere. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to white at the highest elevations. The perspective is toward the west, 20 degrees off horizontal with 2X vertical exaggeration. The back (west) edge of the data set forms a false skyline within the Andes Range.

Elevation data used in this image was acquired by the Shuttle Radar Topography Mission aboard Space Shuttle Endeavour, launched on February 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on Space Shuttle Endeavour in 1994. SRTM was designed to collect three-dimensional measurements of Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 55.0 x 37.2 kilometers ( 34.1 x 23.1 miles) Location: 40.4 deg. South lat., 71.3 deg. West lon. Orientation: West toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

Dilaton-assisted dark matter.

PubMed

Bai, Yang; Carena, Marcela; Lykken, Joseph

2009-12-31

A dilaton could be the dominant messenger between standard model fields and dark matter. The measured dark matter relic abundance relates the dark matter mass and spin to the conformal breaking scale. The dark matter-nucleon spin-independent cross section is predicted in terms of the dilaton mass. We compute the current constraints on the dilaton from LEP and Tevatron experiments, and the gamma-ray signal from dark matter annihilation to dilatons that could be observed by Fermi Large Area Telescope.

Weak mixing below the weak scale in dark-matter direct detection

NASA Astrophysics Data System (ADS)

Brod, Joachim; Grinstein, Benjamin; Stamou, Emmanuel; Zupan, Jure

2018-02-01

If dark matter couples predominantly to the axial-vector currents with heavy quarks, the leading contribution to dark-matter scattering on nuclei is either due to one-loop weak corrections or due to the heavy-quark axial charges of the nucleons. We calculate the effects of Higgs and weak gauge-boson exchanges for dark matter coupling to heavy-quark axial-vector currents in an effective theory below the weak scale. By explicit computation, we show that the leading-logarithmic QCD corrections are important, and thus resum them to all orders using the renormalization group.

Australia, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2004-01-01

Australia is the world's smallest, flattest, and (after Antarctica) driest continent, but at 7.7 million square kilometers (3.0 million square miles) it is also the sixth largest country. Its low average elevation (300 meters, or less than 1000 feet) is caused by its position near the center of a tectonic plate, where there are no volcanic or other geologic forces of the type that raise the topography of other continents. In fact Australia is the only continent without any current volcanic activity at all - the last eruption took place 1400 years ago at Mt. Gambier.

The Australian continent is also one of the oldest land masses, with some of its erosion-exposed bedrock age dated at more than 3 billion years. More than one-fifth of the land area is desert, with more than two-thirds being classified as arid or semi-arid and unsuitable for settlement. The coldest regions are in the highlands and tablelands of Tasmania and the Australian Alps at the southeastern corner of the continent, location of Australia's highest point, Mt. Kosciusko (2228 meters, or 7310 feet.)

Prominent features of Australia include the Lake Eyre basin, the darker green region visible in the center-right. At 16 meters (52 feet) below sea level this depression is one of the largest inland drainage systems in the world, covering more than 1.3 million square kilometers (500,000 square miles). The mountain range near the east coast is called the Great Dividing Range, forming a watershed between east and west flowing rivers. Erosion has created deep valleys, gorges and waterfalls in this range where rivers tumble over escarpments on their way to the sea.

The crescent shaped uniform green region in the south, just left of center, is the Nullarbor Plain, a low-lying limestone plateau which is so flat that the Trans-Australian Railway runs through it in a straight line for more than 483 kilometers (300 miles).

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Location: 45 to 10 degrees South latitude, 112 to 155 degrees East longitude Orientation: North toward the top, Mercator projection Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

Influence of shading on ornamental and physiological characteristics during flower development of groundcover rose (Rosa hybrida L.)

NASA Astrophysics Data System (ADS)

Hou, Wei; Luo, Ya; Wang, Xiaorong; Chen, Qing; Sun, Bo; Wang, Yan; Liu, Zejing; Tang, Haoru; Zhang, Yong

2018-04-01

The objective of the present investigation was to study the effect of shading on flower quality during flower development and photosynthetic capacity of groundcover rose (Rosa hybrida L.). The results showed that shade significantly increased flower diameter, levels of soluble protein and soluble sugar, total carotenoids content and superoxide dismutase (SOD) activity, while contents of malondialdehyde (MDA) and total anthocyanins in shaded flowers were significantly decreased as compared to sun-exposed flowers. However, no significant changes were observed in petal color parameters L*, a*, b* and C* between sun exposure and shade treatment plants at each flower developmental stage. Therefore, groundcover rose seemed to have the capacity to shade condition through auto-regulation. These results could provide us with a theoretical basis for further application of groundcover rose in the greening of urban spaces and an understanding of the mechanisms behind the changes induced by shade.

An in vitro study to evaluate the difference in shade between commercially available shade guides and glazed porcelain.

PubMed

Manimaran, P; Sadan, D Sai

2016-10-01

Smile is one of the most important interactive communication skills of a person. A smile is the key factor for an aesthetic appearance. Hence aesthetics is one of the motivating factor for the patients to seek dental care. Correction of unaesthetic appearance gives a positive effect to the self esteem of the patient. The aim of this study was to compare the difference in the shade between the commercially available shade guides namely Vita Classical And Ivoclar Chromascop and the fired porcelain samples fabricated using Vita Zahnfabrik VMK 95 and Ivoclar Classic Materials respectively. The objective of this study was to obtain a matching brand of material that has a particular shade tab among the brands used. To conclude, Ivoclar material matched the chromascop shade guide better than the vita material matched the vita classic shade guide.

Global limits and interference patterns in dark matter direct detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Catena, Riccardo; Gondolo, Paolo

2015-08-13

We compare the general effective theory of one-body dark matter nucleon interactions to current direct detection experiments in a global multidimensional statistical analysis. We derive exclusion limits on the 28 isoscalar and isovector coupling constants of the theory, and show that current data place interesting constraints on dark matter-nucleon interaction operators usually neglected in this context. We characterize the interference patterns that can arise in dark matter direct detection from pairs of dark matter-nucleon interaction operators, or from isoscalar and isovector components of the same operator. We find that commonly neglected destructive interference effects weaken standard direct detection exclusion limitsmore » by up to one order of magnitude in the coupling constants.« less

Global limits and interference patterns in dark matter direct detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Catena, Riccardo; Gondolo, Paolo, E-mail: riccardo.catena@theorie.physik.uni-goettingen.de, E-mail: paolo.gondolo@utah.edu

2015-08-01

We compare the general effective theory of one-body dark matter nucleon interactions to current direct detection experiments in a global multidimensional statistical analysis. We derive exclusion limits on the 28 isoscalar and isovector coupling constants of the theory, and show that current data place interesting constraints on dark matter-nucleon interaction operators usually neglected in this context. We characterize the interference patterns that can arise in dark matter direct detection from pairs of dark matter-nucleon interaction operators, or from isoscalar and isovector components of the same operator. We find that commonly neglected destructive interference effects weaken standard direct detection exclusion limitsmore » by up to one order of magnitude in the coupling constants.« less

Shading reduces growth of longleaf and loblolly pine seedlings in containers

Treesearch

James P. Barnett

1989-01-01

Development of longleaf (Pinus palustris Mill.) and loblolly (P. taeda L.) pine seediings growing under three light conditions--full sunlight, 30% shade, and 50% shade--was evaluated. Although there was little difference between development of seedlings in 30% and 50% shade, those grown is full sunlight were signiticantly larger...

The effect of shade on chlorophyll and anthocyanin content of upland red rice

NASA Astrophysics Data System (ADS)

Muhidin; Syam'un, E.; Kaimuddin; Musa, Y.; Sadimantara, G. R.; Usman; Leomo, S.; Rakian, T. C.

2018-02-01

Upland red rice (Oryza sativa) is a staple food and contains anthocyanin, which can act as antioxidants, plays an important role both for the plant itself and for human health. Levels of antioxidants in rice can be affected by the availability of light. The results showed that the difference of shade, cultivar, and interaction both significantly affect the content of chlorophyll a, chlorophyll b and total chlorophyll. The results also showed that shade could increase chlorophyll in all cultivars tested. The highest levels of chlorophyll a were present in the moderate shade level (n2), then decreased at the shelter level (n3) and increased again at high levels (n4). While on chlorophyll content b, it appears that shade increased chlorophyll b in all cultivars tested and this increase was linear to the increase of shade. The shade treatment may increase the anthocyanin content and the increase depending on the type of cultivar. Increased levels of anthocyanin highest due to shade occurred on Jangkobembe cultivar. The original level of anthocyanin on Jangkobembe cultivar averaged 0.096 mg g-1 increased to 2.487 mg g-1 or increased 26 fold. It is concluded that the shade had a significant effect on the chlorophyll and anthocyanin content.

[Research on the designing method of a special shade guide for tooth whitening].

PubMed

Xu, Yingxin

2015-10-01

To investigate a method of designing an accurate and scientific shade guide, especially used for judging the effect of tooth whitening, by analyzing the colorimetric values of discolored teeth statistically. One hundred thirty-six pictures of patients who had been receiving the Beyond cold light whitening treatment from February 2009 to July 2014 were analyzed, including 25 tetracycline teeth, 61 mottled-enamel teeth, and 50 yellow teeth. The colorimetric values of discolored teeth were measured. The L* values of shade tabs were calculated by hierarchical clustering of those of discolored teeth. The a* and b* values of shade tabs were the mean of those observed for discolored teeth. Accordingly, different shade guides were designed for each type of discolored teeth, and the effects were evaluated. A statistically significant difference in colorimetric values was found among the three types of discolored teeth. Compared with the Vitapan Classical shade guide, the shade guides designed through the present method were more scientific and accurate in judging the effect of tooth whitening. Moreover, the arrangement of shade tabs was more logical, and the color difference between shade tabs and discolored teeth was smaller. The proposed designing method is theoretically feasible, although its clinical effect has yet to be proven.

The effect of shade and vermicompost application on yield and flavonoid levels of Tempuyung (Sonchus arvensis)

NASA Astrophysics Data System (ADS)

Putri, D. P.; Widyastuti, Y.; Dewi, W. S.; Yunus, A.

2018-03-01

This study aims to determine the effect of shade and vermicompost on yield and level of flavonoids in Tempuyung (Sonchus arvensis). The study was conducted in May- August 2016, in Tegal Gede Village, Kab. Karanganyar. Secondary metabolite content analysis was performed in B2P2TOOT laboratory, Tawangmangu. This study used a Completely Randomized Design (CRD) arranged in a split plot. Treatment consists of shade as main plot and the dose of vermicompost as sub plot. Shade treatments are 0% (without shade), 50% and 75%. The dose of vermicompost are 0 g / polybag (control), 250 g / polybag, 500 g / polybag and 750 g / polybag. Each treatment was repeated 3 times and each in experimental unit consist of 2 sample plants. The results showed that the higher levels of shade tend to decrease vegetative growth of plants. Moreover, vermicompost give significant effect on leaf weight, l number, wet and dry weight. The combination of 0% shade and 750 gram vermicompost gave the highest value (P <0.05) to leaf weight ± 186.68 g, wet weight ± 252.08 g and dry weight ± 30,76 gTempuyung. The combination of 50% shade with 0 g vermicompost and 75% shade with 250 g vermicompost show to increasing the content of flavonoid compounds.

Segmentation-based retrospective shading correction in fluorescence microscopy E. coli images for quantitative analysis

NASA Astrophysics Data System (ADS)

Mai, Fei; Chang, Chunqi; Liu, Wenqing; Xu, Weichao; Hung, Yeung S.

2009-10-01

Due to the inherent imperfections in the imaging process, fluorescence microscopy images often suffer from spurious intensity variations, which is usually referred to as intensity inhomogeneity, intensity non uniformity, shading or bias field. In this paper, a retrospective shading correction method for fluorescence microscopy Escherichia coli (E. Coli) images is proposed based on segmentation result. Segmentation and shading correction are coupled together, so we iteratively correct the shading effects based on segmentation result and refine the segmentation by segmenting the image after shading correction. A fluorescence microscopy E. Coli image can be segmented (based on its intensity value) into two classes: the background and the cells, where the intensity variation within each class is close to zero if there is no shading. Therefore, we make use of this characteristics to correct the shading in each iteration. Shading is mathematically modeled as a multiplicative component and an additive noise component. The additive component is removed by a denoising process, and the multiplicative component is estimated using a fast algorithm to minimize the intra-class intensity variation. We tested our method on synthetic images and real fluorescence E.coli images. It works well not only for visual inspection, but also for numerical evaluation. Our proposed method should be useful for further quantitative analysis especially for protein expression value comparison.

Growth and production of new superior rice varieties in the shade intensity

NASA Astrophysics Data System (ADS)

Alridiwirsah; Harahap, E. M.; Akoeb, E. N.; Hanum, H.

2018-02-01

Shade intensity is one of the most important requirements for plant growth, affecting growth, development, survival, and crop productivity. This study aims to evaluate the growth and productiom of New Superior Rice Varieties In The shade Intensity. This study was conducted in Balai Pengkajian Teknologi Pertanian, Pagar Merbau, Deli Serdang, North Sumatra. The research used completely randomized design with twofactors. The shade intensity (N) were 25%, 50% and no shade intensity as a control. Whereas new superior rice varieties were V1: Inpara 2, V2: Suluttan Unsrat 2, V3: Inpari Mugibat, V4: Inpari Sidenuk, V5: Mekongga, V6: Ciherang, V7:Inpari 10, V8: Inpari 3, V9: Inpari 4, V10: Inpari 30, dan V11: Cibogo. The result indicated that new superior rice varietiesshowedsignificant effectonthe growth and productionvariablesuch as leaf area, where Inpari Sidenuk variety was the highest among the varieties. Total chorophyll, the highest was found on Inpari variety. Number of tillers and plant height where the highest was found on Ciherang variety. The shade intensity showed significant effect on leaf area, where 25% shade intensity was the highest. Total chlorophyll, the highest was found on 50% shade intensity, number of tillers, the highest was found on no shade intensity.

Shading decreases the abundance of the herbivorous California horn snail, Cerithidea californica

USGS Publications Warehouse

Lorda, Julio; Lafferty, Kevin D.

2012-01-01

Most of the intertidal zone in estuaries of California, USA and Baja California, Mexico is covered with vascular vegetation. Shading by these vascular plants influences abiotic and biotic processes that shape benthic community assemblages. We present data on the effects of shading on the California horn snail, Cerithidea californica. This species is important because it is the most common benthic macrofaunal species in these systems and acts as an obligate intermediate host of several species of rematode parasites that infect several other species. Using observational and experimental studies, we found a negative effect of shade on the distribution and abundance of the California horn snail. We hypothesized that shading reduces the abundance of the epipelic diatoms that the snails feeds on, causing snails to leave haded areas. We observed a negative relationship between vascular plant cover, sub-canopy light levels, and snail density in Mugu Lagoon. Then we experimentally manipulated light regimes, by clipping vegetation and adding shade structures, and found higher snail densities at higher light levels. In Goleta Slough, we isolated the effect of shade from vegetation by documenting a negative relationship between the shade created by two bridges and diatom and snail densities. We also found that snails moved the greatest distances over shaded channel banks compared to unshaded channel banks. Further, we documented the effect of water depth and channel bank orientation on shading in this system. An additional effect of shading is the reduction of temperature, providing an alternative explanation for some of our results. These results broaden our knowledge of how variation in the light environment influences the ecology of estuarine ecosystems.

Could digital imaging be an alternative for digital colorimeters?

PubMed

Caglar, Alper; Yamanel, Kivanc; Gulsahi, Kamran; Bagis, Bora; Ozcan, Mutlu

2010-12-01

This study evaluated the colour parameters of composite and ceramic shade guides determined using a colorimeter and digital imaging method with illuminants at different colour temperatures. Two different resin composite shade guides, namely Charisma (Heraeus Kulzer) and Premise (Kerr Corporation), and two different ceramic shade guides, Vita Lumin Vacuum (VITA Zahnfabrik) and Noritake (Noritake Co.), were evaluated at three different colour temperatures (2,700 K, 2,700-6,500 K, and 6500 K) of illuminants. Ten shade tabs were selected (A1, A2, A3, A3,5, A4, B1, B2, B3, C2 and C3) from each shade guide. CIE Lab values were obtained using digital imaging and a colorimeter (ShadeEye NCC Dental Chroma Meter, Shofu Inc.). The data were analysed using two-way ANOVA, and Pearson's correlation. While mean L* values of both composite and ceramic shade guides were not affected from the colour temperature, L* values obtained with the colorimeter showed significantly lower values than those of the digital imaging (p < 0.01). At combined 2,700-6500 K colour temperature, the means of a* values obtained from colorimeter and digital imaging did not show significant differences (p > 0.05). For both composite and ceramic shade guides, L* and b* values obtained from colorimeter and digital imaging method presented a high level of correlation. High-level correlations were also acquired for a* values in all shade guides except for the Charisma composite shade guide. Digital imaging method could be an alternative for the colorimeters unless the proper object-camera distance, digital camera settings and suitable illumination conditions could be supplied. However, variations in shade guides, especially for composites, may affect the correlation.

Shade matching assisted by digital photography and computer software.

PubMed

Schropp, Lars

2009-04-01

To evaluate the efficacy of digital photographs and graphic computer software for color matching compared to conventional visual matching. The shade of a tab from a shade guide (Vita 3D-Master Guide) placed in a phantom head was matched to a second guide of the same type by nine observers. This was done for twelve selected shade tabs (tests). The shade-matching procedure was performed visually in a simulated clinic environment and with digital photographs, and the time spent for both procedures was recorded. An alternative arrangement of the shade tabs was used in the digital photographs. In addition, a graphic software program was used for color analysis. Hue, chroma, and lightness values of the test tab and all tabs of the second guide were derived from the digital photographs. According to the CIE L*C*h* color system, the color differences between the test tab and tabs of the second guide were calculated. The shade guide tab that deviated least from the test tab was determined to be the match. Shade matching performance by means of graphic software was compared with the two visual methods and tested by Chi-square tests (alpha= 0.05). Eight of twelve test tabs (67%) were matched correctly by the computer software method. This was significantly better (p < 0.02) than the performance of the visual shade matching methods conducted in the simulated clinic (32% correct match) and with photographs (28% correct match). No correlation between time consumption for the visual shade matching methods and frequency of correct match was observed. Shade matching assisted by digital photographs and computer software was significantly more reliable than by conventional visual methods.

Effect of abutment shade, ceramic thickness, and coping type on the final shade of zirconia all-ceramic restorations: in vitro study of color masking ability.

PubMed

Oh, Seon-Hee; Kim, Seok-Gyu

2015-10-01

The aim of the study was to evaluate the effect of abutment shade, ceramic thickness, and coping type on the final shade of zirconia all-ceramic restorations. Three different types of disk-shaped zirconia coping specimens (Lava, Cercon, Zirkonzahn: ø10 mm × 0.4 mm) were fabricated and veneered with IPS e.max Press Ceram (shade A2), for total thicknesses of 1 and 1.5 mm. A total of sixty zirconia restoration specimens were divided into six groups based on their coping types and thicknesses. The abutment specimens (ø10 mm × 7 mm) were prepared with gold alloy, base metal (nickel-chromium) alloy, and four different shades (A1, A2, A3, A4) of composite resins. The average L*, a*, b* values of the zirconia specimens on the six abutment specimens were measured with a dental colorimeter, and the statistical significance in the effects of three variables was analyzed by using repeated measures analysis of variance (α=.05).The average shade difference (ΔE) values of the zirconia specimens between the A2 composite resin abutment and other abutments were also evaluated. The effects of zirconia specimen thickness (P<.001), abutment shade (P<.001), and type of zirconia copings (P<.003) on the final shade of the zirconia restorations were significant. The average ΔE value of Lava specimens (1 mm) between the A2 composite resin and gold alloy abutments was higher (close to the acceptability threshold of 5.5 ΔE) than th ose between the A2 composite resin and other abutments. This in-vitro study demonstrated that abutment shade, ceramic thickness, and coping type affected the resulting shade of zirconia restorations.

Potential energy savings with exterior shades in large office buildings and the impact of discomfort glare

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffmann, Sabine; Lee, Eleanor

Exterior shades are highly efficient for reducing solar load in commercial buildings. Their impact on net energy use depends on the annual energy balance of heating, cooling, fan and lighting energy. This paper discusses the overall energy use intensity of various external shading systems for a prototypical large office building split into the different types of energy use and for different orientations and window sizes. Lighting energy was calculated for a constant lighting power as well as for dimmed lighting fixtures (daylighting control). In Section 3, slat angles and solar cut-off angles were varied for fixed exterior slat shading systems.more » While the most light-blocking shades performed best for the case without daylighting controls, the optimum cut-off angle with daylighting controls was found to be 30 deg for the office building prototype used in Chicago and Houston. For large window-to-wall (WWR) ratios, window related annual energy use could be reduced by at least 70 % without daylighting control and by a minimum of 86 % with daylighting control in average over all orientations. The occurrence of discomfort glare was is considered in Section 4 of the paper, which looks at the performance of commercially available exterior shading systems when an interior shade is used in addition to the exterior shade during hours when occupants would experience discomfort glare. Glare control impacts overall energy use intensity significantly for exterior shades with high transmittance, especially when daylighting controls are used. In these cases, exterior shades are only beneficial for window-to-wall areas ≥ 45% in the hot Houston climate. For smaller windows and in a heating/cooling climate like Chicago, exterior shades can increase energy consumption« less

Dirac dark matter and b →s ℓ+ℓ- with U(1) gauge symmetry

NASA Astrophysics Data System (ADS)

Celis, Alejandro; Feng, Wan-Zhe; Vollmann, Martin

2017-02-01

We revisit the possibility of a Dirac fermion dark matter candidate in the light of current b →s ℓ+ℓ- anomalies by investigating a minimal extension of the Standard Model with a horizontal U(1 ) ' local symmetry. Dark matter stability is protected by a remnant Z2 symmetry arising after spontaneous symmetry breaking of U(1 ) '. The associated Z' gauge boson can accommodate current hints of new physics in b →s ℓ+ℓ- decays, and acts as a vector portal between dark matter and the visible sector. We find that the model is severely constrained by a combination of precision measurements at flavor factories, LHC searches for dilepton resonances, as well as direct and indirect dark matter searches. Despite this, viable regions of the parameter space accommodating the observed dark matter relic abundance and the b →s ℓ+ℓ-anomalies still persist for dark matter and Z ' masses in the TeV range.

Assessment of color parameters of composite resin shade guides using digital imaging versus colorimeter.

PubMed

Yamanel, Kivanc; Caglar, Alper; Özcan, Mutlu; Gulsah, Kamran; Bagis, Bora

2010-12-01

This study evaluated the color parameters of resin composite shade guides determined using a colorimeter and digital imaging method. Four composite shade guides, namely: two nanohybrid (Grandio [Voco GmbH, Cuxhaven, Germany]; Premise [KerrHawe SA, Bioggio, Switzerland]) and two hybrid (Charisma [Heraeus Kulzer, GmbH & Co. KG, Hanau, Germany]; Filtek Z250 [3M ESPE, Seefeld, Germany]) were evaluated. Ten shade tabs were selected (A1, A2, A3, A3,5, A4, B1, B2, B3, C2, C3) from each shade guide. CIE Lab values were obtained using digital imaging and a colorimeter (ShadeEye NCC Dental Chroma Meter, Shofu Inc., Kyoto, Japan). The data were analyzed using two-way analysis of variance and Bonferroni post hoc test. Overall, the mean ΔE values from different composite pairs demonstrated statistically significant differences when evaluated with the colorimeter (p < 0.001) but there was no significant difference with the digital imaging method (p = 0.099). With both measurement methods in total, 80% of the shade guide pairs from different composites (97/120) showed color differences greater than 3.7 (moderately perceptible mismatch), and 49% (59/120) had obvious mismatch (ΔE > 6.8). For all shade pairs evaluated, the most significant shade mismatches were obtained between Grandio-Filtek Z250 (p = 0.021) and Filtek Z250-Premise (p = 0.01) regarding ΔE mean values, whereas the best shade match was between Grandio-Charisma (p = 0.255) regardless of the measurement method. The best color match (mean ΔE values) was recorded for A1, A2, and A3 shade pairs in both methods. When proper object-camera distance, digital camera settings, and suitable illumination conditions are provided, digital imaging method could be used in the assessment of color parameters. Interchanging use of shade guides from different composite systems should be avoided during color selection. © 2010, COPYRIGHT THE AUTHORS. JOURNAL COMPILATION © 2010, WILEY PERIODICALS, INC.

Lightness, chroma, and hue distributions of a shade guide as measured by a spectroradiometer.

PubMed

Lee, Yong-Keun; Yu, Bin; Lim, Ho-Nam

2010-09-01

The color attributes of commercially available shade guides have been measured by spectrophotometers (SP), which are designed to measure flat surfaces. However, there is limited information on the color distribution of shade guides as measured by spectroradiometers (SR), which are capable of measuring the color of curved surfaces. The purpose of this study was to determine the distributions of lightness (CIE L*) and chroma (C*(ab)) step intervals between adjacent shade tabs of a shade guide based on the lightness, chroma, and hue attributes measured by an SR. Lightness, chroma, hue angle, and CIE a* and b* values of the shade tabs (n=26) from a shade guide (Vitapan 3D-Master) were measured by an SR under daylight conditions. The distributions of the ratios in lightness and chroma of each tab compared with the lowest lightness tab or the lowest chroma tab were determined. The values for each color parameter were analyzed by a 3-way ANOVA with the factors of lightness, chroma, and hue designations of the shade tabs (alpha=.05). The chroma and CIE a* and b* values were influenced by the lightness, chroma, and hue designations of the shade tabs (P<.001); however, the lightness and hue angle were influenced by the lightness and hue designations, but not by the chroma designation. Distributions for the CIE a* and b* values, in each lightness group, corresponded with the chroma designation. However, the intervals in the lightness and chroma scales between adjacent tabs were not uniform. The intervals in the color parameters between adjacent shade tabs were not uniform based on SR measurements. Therefore, a shade guide in which shade tabs are more equally spaced by the color attributes, based on the values as measured by an SR along with observers' responses with respect to the equality of the intervals, should be devised. Copyright © 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Evaluating factors that affect the shade-matching ability of dentists, dental staff members and laypeople.

PubMed

Capa, Nuray; Malkondu, Ozlem; Kazazoglu, Ender; Calikkocaoglu, Senih

2010-01-01

The authors conducted a study to evaluate the influence of dentists' and nondentists' experience, age, sex, eye color and use of eyeglasses or contact lenses on tooth shade-matching ability. The authors included 120 participants in this study conducted in Istanbul (periodontists, oral and maxillofacial surgeons, orthodontists, endodontists, pediatric dentists, prosthodontists, restorative dentists, general dentists in private practice, dental technicians, dental assistants, dental assistant students and laypeople). The authors assigned participants to one of three groups: group 1 was composed of prosthodontists, restorative dentists and dental technicians; group 2 consisted of other dental specialists and general dentists; and group 3 included dental assistants, dental assistant students and laypeople. The authors asked participants to match the shades of three artificial maxillary right central incisors (Vitapan acrylic teeth [shades 2L1.5, 1M2, 2R1.5], Vita Zahnfabrik, Bad Säckingen, Germany) by using a shade guide system (Vita Toothguide 3D-Master, Vita Zahnfabrik). They calculated shade matching for the three color components (value, hue, chroma) and analyzed the results by using a chi(2) test. The rate of success in matching the shade for IM2 was 53.3 percent for participants in group 1, 30 percent for participants in group 2 and 20 percent for participants in group 3 (P = .017). However, there were no significant differences between the three groups for shades 2L1.5 and 2R1.5. Professional experience (P = .003) and age (P = .027) were associated with shade-matching success for tooth shade 2L1.5 only. The results showed no statistically significant differences with respect to sex, eye color or use of eyeglasses or contact lenses. Dental care professionals who routinely performed restorative procedures matched the shades better than did participants in other groups. Professional experience was associated positively with the outcome, while sex, eye color and use of eyeglasses or contact lenses did not have any effect on shade-matching results. To improve shade-matching skills, clinicians should participate in hands-on courses, continuing education classes and other training programs.

Colour parameters and shade correspondence of CAD-CAM ceramic systems.

PubMed

Della Bona, Alvaro; Pecho, Oscar E; Ghinea, Razvan; Cardona, Juan C; Pérez, María M

2015-06-01

To evaluate colour differences between (1) CAD-CAM ceramic systems considering shades A1, A2 and A3 and the corresponding nominal shade of VC (Vita Classical shade guide) and (2) shades A1-A2, A2-A3 and A1, A2 and A3 within the same ceramic system. Samples of shades A1, A2 and A3 were fabricated (n=5) from CAD-CAM ceramic blocks (IPS e.max(®) CAD LT and HT, IPS Empress(®) CAD LT and HT, Paradigm™ C, and VITABLOCS(®) Mark II) and polished to 1.0±0.01mm in thickness. Spectral reflectance and colour coordinates were measured using a spectroradiometer inside a viewing booth using the CIE D65 illuminant and the d/0° geometry. Spectral reflectance curves were compared using VAF coefficient and were statistically analyzed using Kruskal-Wallis and the Mann-Whitney U test (α=0.05). Colour coordinates were statistically analyzed using one-way ANOVA, Tukey's test with Bonferroni correction (α=0.001). All colour differences (ΔEab(*) and ΔE00) were analyzed through comparisons with the PT - perceptibility and AT - acceptability thresholds for dental ceramics. ΔE between ceramic systems and its corresponding shade ranged from 6.32 to 13.42 (ΔEab(*)) and 4.48 to 9.30 (ΔE00). ΔE between shades A1-A2, A2-A3 and A1, A2 and A3 ranged, respectively, 1.93-4.82, 1.22-5.59 and 3.63-8.84 (ΔEab(*)); 1.54-3.87, 1.03-3.90 and 2.95-6.51 (ΔE00). Considering the corresponding nominal shade from VC, none of the ceramic systems showed colour differences below the AT. In addition, some ceramic systems showed colour differences below AT (shades A1-A2 and A2-A3) and below PT (shades A2-A3). Careful adjustments should be made to the final shade of CAD-CAM ceramic restorations to reach a clinically acceptable shade match. Copyright © 2015 Elsevier Ltd. All rights reserved.

Color distribution of a shade guide in the value, chroma, and hue scale.

PubMed

Ahn, Jin-Soo; Lee, Yong-Keun

2008-07-01

Shade tabs in a shade guide are matched to teeth in the order of value, hue, and chroma; therefore, information on the distribution of shade tabs is essential for clinical application of a shade guide. However, there is limited information on the color distribution as sorted by these 3 parameters of a recently introduced shade guide. The purposes of this study were to determine the color distributions of tabs from a shade guide in the value (CIE L*), chroma (C*(ab)), and hue scale, and to determine the distribution of step intervals between adjacent tabs by value and chroma. The color of shade tabs (n=29) from a shade guide (Vitapan 3D-Master) was measured to determine the distribution of shade tabs by the value, chroma, hue angle, and CIE a* and b* values. The distribution of the ratios of the value and the chroma of each tab, when compared with the lowest value tab or the lowest chroma tab, was also determined. The data for each color parameter were analyzed by a 3-way ANOVA with the factors of value, chroma, and hue designations of the tabs (alpha=.05). The value, chroma, hue angle, and CIE a* and b* values were influenced by the value, chroma, and hue designations of shade tabs (P<.001). The distributions of the chroma of the tabs within the same value group were relatively ordered, but the values of different value groups overlapped in several instances. Distributions for the CIE a* and b* values reflected the chroma designations in each value group. In the same value group, L, M, and R hue designations corresponded with the manufacturer's stated hue, such as a yellow hue for the L designation and a red hue for the R designation. The distance in the value and chroma scales between adjacent tabs was not uniform. The color distribution of the Vitapan 3D-Master shade guide was more ordered than previously reported color distributions of other, traditional shade guides. However, the interval in the color parameters between adjacent tabs was not uniform; therefore, shade tabs spaced equally, according to the color parameters, should be studied based on the observer's response data.

Sprinklers and shade cool cows and reduce insect-avoidance behavior in pasture-based dairy systems.

PubMed

Kendall, P E; Verkerk, G A; Webster, J R; Tucker, C B

2007-08-01

The body temperature of dairy cows in pastoral systems during summer reaches a peak during and following the p.m. milking. Shade and sprinklers can be used separately or in combination at the milking parlor to reduce heat load. Farmers anecdotally report that the use of sprinklers reduces irritation from insects that occurs while cows are waiting for milking. Once daily, we assessed the effectiveness of short-term exposure to shade and sprinklers for cooling cows [via respiration rate and body (vaginal) temperature] and reducing insect-avoidance behaviors before the p.m. milking in a pasture-based dairy system. Head position was measured as an indicator of whether cattle were avoiding water from the sprinklers. Forty-eight Holstein-Friesian dairy cows were divided into 12 groups (4 cows per group, n = 3 groups/treatment) and were exposed to 1 of 4 treatments for 90 min before the p.m. milking: 1) shade, 2) sprinklers, 3) shade and sprinklers, or 4) uncooled control. Respiration rate was reduced by 30% with shade alone compared with controls [54 vs. 78 +/- 2.3 ( +/- SED) breaths/min, respectively]. Sprinklers alone (30 +/- 2.3 breaths/min) and the combined effects of shade and sprinklers (24 +/- 2.3 breaths/min) reduced the respiration rate by 60 and 67%, respectively, compared with controls. Shaded cows had lower body temperatures during the 90-min treatment period compared with controls (shade: 38.6 degrees C; shade and sprinklers: 38.6 degrees C; control: 38.9 +/- 0.09 degrees C). The decrease in body temperature of cows under sprinklers was more marked than for shade alone and remained lower for at least 4 h after milking (sprinklers: 38.7 degrees C; shade and sprinklers: 38.6 degrees C; shade: 38.9 degrees C; control: 39.2 +/- 0.10 degrees C). The sprinkler treatment reduced the number of tail flicks (control: 12.6 vs. sprinklers: 6.6 +/- 2.4 flicks/min) and hoof stamps (control: 4.4 vs. sprinkler: 2.2 +/- 0.5 stamps/min). Cows exposed to sprinklers spent more time with their heads lowered compared with cows in the shaded and control treatments. The reductions in body temperature and respiration rate attributable to shade and sprinklers were greatest when the temperature-humidity index and heat-load index were > or = 69 and 77, respectively, and cows benefited from cooling when these levels were exceeded.

Chlorophyll fluorescence kinetics, photosynthetic activity, and pigment composition of blue-shade and half-shade leaves as compared to sun and shade leaves of different trees.

PubMed

Lichtenthaler, Hartmut K; Babani, Fatbardha; Navrátil, Martin; Buschmann, Claus

2013-11-01

The chlorophyll (Chl) fluorescence induction kinetics, net photosynthetic CO2 fixation rates P N, and composition of photosynthetic pigments of differently light exposed leaves of several trees were comparatively measured to determine the differences in photosynthetic activity and pigment adaptation of leaves. The functional measurements were carried out with sun, half-shade and shade leaves of seven different trees species. These were: Acer platanoides L., Ginkgo biloba L., Fagus sylvatica L., Platanus x acerifolia Willd., Populus nigra L., Quercus robur L., Tilia cordata Mill. In three cases (beech, ginkgo, and oak), we compared the Chl fluorescence kinetics and photosynthetic rates of blue-shade leaves of the north tree crown receiving only blue sky light but no direct sunlight with that of sun leaves. In these cases, we also determined in detail the pigment composition of all four leaf types. In addition, we determined the quantum irradiance and spectral irradiance of direct sunlight, blue skylight as well as the irradiance in half shade and full shade. The results indicate that sun leaves possess significantly higher mean values for the net CO2 fixation rates P N (7.8-10.7 μmol CO2 m(-2) s(-1) leaf area) and the Chl fluorescence ratio R Fd (3.85-4.46) as compared to shade leaves (mean P N of 2.6-3.8 μmol CO2 m(-2) s(-1) leaf area.; mean R Fd of 1.94-2.56). Sun leaves also exhibit higher mean values for the pigment ratio Chl a/b (3.14-3.31) and considerably lower values for the weight ratio total chlorophylls to total carotenoids, (a + b)/(x + c), (4.07-4.25) as compared to shade leaves (Chl a/b 2.62-2.72) and (a + b)/(x + c) of 5.18-5.54. Blue-shade and half-shade leaves have an intermediate position between sun and shade leaves in all investigated parameters including the ratio F v/F o (maximum quantum yield of PS2 photochemistry) and are significantly different from sun and shade leaves but could not be differentiated from each other. The mean values of the Chl fluorescence decrease ratio R Fd of blue-shade and half-shade leaves fit well into the strong linear correlation with the net photosynthetic rates P N of sun and shade leaves, thus unequivocally indicating that the determination of the Chl fluorescence decrease ratio R Fd is a fast and indirect measurement of the photosynthetic activity of leaves. The investigations clearly demonstrate that the photosynthetic capacity and pigment composition of leaves and chloroplasts strongly depend on the amounts and quality of light received by the leaves.

Dynamics of domain coverage of the protein sequence universe.

PubMed

Rekapalli, Bhanu; Wuichet, Kristin; Peterson, Gregory D; Zhulin, Igor B

2012-11-16

The currently known protein sequence space consists of millions of sequences in public databases and is rapidly expanding. Assigning sequences to families leads to a better understanding of protein function and the nature of the protein universe. However, a large portion of the current protein space remains unassigned and is referred to as its "dark matter". Here we suggest that true size of "dark matter" is much larger than stated by current definitions. We propose an approach to reducing the size of "dark matter" by identifying and subtracting regions in protein sequences that are not likely to contain any domain. Recent improvements in computational domain modeling result in a decrease, albeit slowly, in the relative size of "dark matter"; however, its absolute size increases substantially with the growth of sequence data.

Exploring the effects of overburden on the sublimation and transport of H2O on Iapetus

NASA Astrophysics Data System (ADS)

Rivera-Valentin, Edgard G.; Blackburn, David G.; Ulrich, Richard K.

2012-08-01

It has been shown through both measurements and simulations that there exists a measurable ice-free, porous, overburden overlaying water ice on Cassini Regio. Mass transfer through this porous media in a vacuum would occur in the Knudsen regime, which provides sublimation rates orders of magnitude smaller than Hertz-Langmuir sublimation. The availability of water ice for transport from this region is thus currently controlled by mass transfer through the dark material overburden. Thermal segregation suggests that Iapetus' polar regions have been brightened via ballistic transport of water and its subsequent cold trapping since exogenic deposition models predict dark high latitudes on the leading hemisphere. The limiting effect of the dark material on transport of water ice may thus greatly impact the current mass balance at the poles. The effects of the overburden on the global stability and transport of H2O is addressed in order to gain insight into its influence on the polar albedo distribution and current state of thermal segregation within the dark terrain. Results indicate that thermal segregation is currently an inactive or weak process within Cassini Regio, though it is an ongoing process at the inter-terrain regions. Modeling of polar accumulation suggests that even accounting for the current dark material cover within Cassini Regio there exists sufficient ballistically inbound water to overcome exogenic darkening mechanisms. Topographic effects on local albedo differences are also simulated to provide a more complete water stability study of Iapetus. Results suggest that topographically induced changes in heat flux may be sufficient to create the observed local albedo contrasts and also support ongoing dark exogenic deposition within Cassini Regio to explain the lack of bright slopes deep within the dark terrain.

A CLIMATE-RESPONSIVE ADAPTIVE CONTROL FOR A COMBINATION PASSIVE SOLAR SHADING AND NATURAL VENTILATION

EPA Science Inventory

Currently, nations around the globe are facing striking concerns regarding energy consumption. In the United States, we face increasing demands that will cause increasing fuel prices thus ultimately higher-energy cost. The future could be eased by reduce energy consumption ...

The least-squares mixing models to generate fraction images derived from remote sensing multispectral data

NASA Technical Reports Server (NTRS)

Shimabukuro, Yosio Edemir; Smith, James A.

1991-01-01

Constrained-least-squares and weighted-least-squares mixing models for generating fraction images derived from remote sensing multispectral data are presented. An experiment considering three components within the pixels-eucalyptus, soil (understory), and shade-was performed. The generated fraction images for shade (shade image) derived from these two methods were compared by considering the performance and computer time. The derived shade images are related to the observed variation in forest structure, i.e., the fraction of inferred shade in the pixel is related to different eucalyptus ages.

Evolution of separate screening soliton pairs in a biased series photorefractive crystal circuit.

PubMed

Liu, Jinsong; Hao, Zhonghua

2002-06-01

This paper presents calculations for an idea in photorefractive spatial soliton, namely, screening solitons form in a biased series photorefractive crystal circuit consisting of two photorefractive crystals connected electronically by electrode leads in a chain with a voltage source. A system of two coupled equations is derived under appropriate conditions for two-beam propagation in the crystal circuit. The possibility of obtaining steady-state bright and dark screening soliton solutions is investigated in one dimension and, the existence of dark-dark, bright-dark, and bright-bright separate screening soliton pairs in such a circuit is proved. The numerical results show that the two solitons in a soliton pair can affect each other by the light-induced current and their coupling can affect their spatial profiles, dynamical evolutions, stabilities, and self-deflection. Under the limit in which the optical wave has a spatial extent much less than the width of the crystal, only the dark soliton can affect the other soliton by the light-induced current, but the bright soliton cannot. For a bright-dark or dark-dark soliton pair, the dark soliton in a weak input intensity can be obtained for a larger nonlinearity than for a stronger input intensity. For a bright-dark soliton pair, increasing the input intensity of the dark soliton can increase the bending angle of the bright soliton. Some potential applications are discussed.

Electronic Properties of Grain Boundaries in GaAs: A Study of Oriented Bicrystals Prepared by Epitaxial Lateral Overgrowth.

DTIC Science & Technology

1984-05-10

overgrowth from a spoke 90 pattern of radial stripe openings at 1 intervals on an Si0 2 coated (110) surface. Bright regions are GaAs and dark regions are Si0...the dark current for such an ideal device is given by Idark - Io[exp(eVbi/AokT) - 1] , (11-l) where Io is a proportionality constant describing the...recombination and leakage currents which contribute to an increased dark current. The value of Voc is determined by the built-in junction barrier height and the

Stressed Ge:Ga photoconductors for space-based astronomy. (Is there life beyond 120 micron)

NASA Technical Reports Server (NTRS)

Beeman, J. W.; Haller, E. E.; Hansen, W. L.; Luke, P. N.; Richards, P. L.

1989-01-01

Information is given in viewgraph form. Information is given on the characteristics of stressed Ge:Ga, a spring type stress cavity, mounting hardware, materials parameters affecting dark current, and the behavior of low dark current stressed Ge:Ga. It is concluded that detectors exist today for background-limited detection at 200 microns, that researchers are narrowing in on the significant parameters that effect dark current in stressed photoconductors, that these findings may be applied to other photoconductor materials, and that some creative problem solving for an ionizing effect reset mechanism is needed.

Theoretical analysis of nBn infrared photodetectors

NASA Astrophysics Data System (ADS)

Ting, David Z.; Soibel, Alexander; Khoshakhlagh, Arezou; Gunapala, Sarath D.

2017-09-01

The depletion and surface leakage dark current suppression properties of unipolar barrier device architectures such as the nBn have been highly beneficial for III-V semiconductor-based infrared detectors. Using a one-dimensional drift-diffusion model, we theoretically examine the effects of contact doping, minority carrier lifetime, and absorber doping on the dark current characteristics of nBn detectors to explore some basic aspects of their operation. We found that in a properly designed nBn detector with highly doped excluding contacts the minority carriers are extracted to nonequilibrium levels under reverse bias in the same manner as the high operating temperature (HOT) detector structure. Longer absorber Shockley-Read-Hall (SRH) lifetimes result in lower diffusion and depletion dark currents. Higher absorber doping can also lead to lower diffusion and depletion dark currents, but the benefit should be weighted against the possibility of reduced diffusion length due to shortened SRH lifetime. We also briefly examined nBn structures with unintended minority carrier blocking barriers due to excessive n-doping in the unipolar electron barrier, or due to a positive valence band offset between the barrier and the absorber. Both types of hole blocking structures lead to higher turn-on bias, although barrier n-doping could help suppress depletion dark current.

UV detector based on InAlN/GaN-on-Si HEMT stack with photo-to-dark current ratio > 107

NASA Astrophysics Data System (ADS)

kumar, Sandeep; Pratiyush, Anamika Singh; Dolmanan, Surani B.; Tripathy, Sudhiranjan; Muralidharan, Rangarajan; Nath, Digbijoy N.

2017-12-01

We demonstrate an InAlN/GaN-on-Si high electron mobility transistor based UV detector with a photo-to-dark current ratio of >107. The Ti/Al/Ni/Au metal stack was evaporated and thermal annealed rapidly for Ohmic contacts to the 2D electron gas (2DEG) at the InAlN/GaN interface, while the channel + barrier was recess etched to a depth of 20 nm to pinch-off the 2DEG between Source-Drain pads. A spectral responsivity (SR) of 32.9 A/W at 367 nm was measured at 5 V. A very high photo-to-dark current ratio of >107 was measured at a bias of 20 V. The photo-to-dark current ratio at a fixed bias was found to be decreasing with an increase in the recess length of photodetectors. The fabricated devices were found to exhibit a UV-to-visible rejection ratio of >103 with a low dark current of < 32 pA at 5 V. Transient measurements showed rise and fall times in the range of 3-4 ms. The gain mechanism was investigated, and carrier lifetimes were estimated which matched well with those reported elsewhere.

Comparison of Measured Dark Current Distributions with Calculated Damage Energy Distributions in HgCdTe

NASA Technical Reports Server (NTRS)

Marshall, C. J.; Marshall, P. W.; Howe, C. L.; Reed, R. A.; Weller, R. A.; Mendenhall, M.; Waczynski, A.; Ladbury, R.; Jordan, T. M.

2007-01-01

This paper presents a combined Monte Carlo and analytic approach to the calculation of the pixel-to-pixel distribution of proton-induced damage in a HgCdTe sensor array and compares the results to measured dark current distributions after damage by 63 MeV protons. The moments of the Coulombic, nuclear elastic and nuclear inelastic damage distributions were extracted from Monte Carlo simulations and combined to form a damage distribution using the analytic techniques first described in [1]. The calculations show that the high energy recoils from the nuclear inelastic reactions (calculated using the Monte Carlo code MCNPX [2]) produce a pronounced skewing of the damage energy distribution. While the nuclear elastic component (also calculated using the MCNPX) contributes only a small fraction of the total nonionizing damage energy, its inclusion in the shape of the damage across the array is significant. The Coulombic contribution was calculated using MRED [3-5], a Geant4 [4,6] application. The comparison with the dark current distribution strongly suggests that mechanisms which are not linearly correlated with nonionizing damage produced according to collision kinematics are responsible for the observed dark current increases. This has important implications for the process of predicting the on-orbit dark current response of the HgCdTe sensor array.

Lateral amorphous selenium metal-insulator-semiconductor-insulator-metal photodetectors using ultrathin dielectric blocking layers for dark current suppression

NASA Astrophysics Data System (ADS)

Chang, Cheng-Yi; Pan, Fu-Ming; Lin, Jian-Siang; Yu, Tung-Yuan; Li, Yi-Ming; Chen, Chieh-Yang

2016-12-01

We fabricated amorphous selenium (a-Se) photodetectors with a lateral metal-insulator-semiconductor-insulator-metal (MISIM) device structure. Thermal aluminum oxide, plasma-enhanced chemical vapor deposited silicon nitride, and thermal atomic layer deposited (ALD) aluminum oxide and hafnium oxide (ALD-HfO2) were used as the electron and hole blocking layers of the MISIM photodetectors for dark current suppression. A reduction in the dark current by three orders of magnitude can be achieved at electric fields between 10 and 30 V/μm. The effective dark current suppression is primarily ascribed to electric field lowering in the dielectric layers as a result of charge trapping in deep levels. Photogenerated carriers in the a-Se layer can be transported across the blocking layers to the Al electrodes via Fowler-Nordheim tunneling because a high electric field develops in the ultrathin dielectric layers under illumination. Since the a-Se MISIM photodetectors have a very low dark current without significant degradation in the photoresponse, the signal contrast is greatly improved. The MISIM photodetector with the ALD-HfO2 blocking layer has an optimal signal contrast more than 500 times the contrast of the photodetector without a blocking layer at 15 V/μm.

Origin of large dark current increase in InGaAs/InP avalanche photodiode

NASA Astrophysics Data System (ADS)

Wen, J.; Wang, W. J.; Chen, X. R.; Li, N.; Chen, X. S.; Lu, W.

2018-04-01

The large dark current increase near the breakdown voltage of an InGaAs/InP avalanche photodiode is observed and analyzed from the aspect of bulk defects in the device materials. The trap level information is extracted from the temperature-dependent electrical characteristics of the device and the low temperature photoluminescence spectrum of the materials. Simulation results with the extracted trap level taken into consideration show that the trap is in the InP multiplication layer and the trap assisted tunneling current induced by the trap is the main cause of the large dark current increase with the bias from the punch-through voltage to 95% breakdown voltage.

Proton radiation effect on performance of InAs/GaSb complementary barrier infrared detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soibel, Alexander; Rafol, Sir B.; Khoshakhlagh, Arezou

In this work, we investigated the effect of proton irradiation on the performance of long wavelength infrared InAs/GaSb photodiodes (λ{sub c} = 10.2 μm), based on the complementary barrier infrared detector design. We found that irradiation with 68 MeV protons causes a significant increase of the dark current from j{sub d} = 5 × 10{sup −5} A/cm{sup 2} to j{sub d} = 6 × 10{sup −3} A/cm{sup 2}, at V{sub b} = 0.1 V, T = 80 K and fluence 19.2 × 10{sup 11 }H{sup +}/cm{sup 2}. Analysis of the dark current as a function of temperature and bias showed that the dominant contributor to the dark current in these devices changes from diffusion current to tunneling current after proton irradiation.more » This change in the dark current mechanism can be attributed to the onset of surface leakage current, generated by trap-assisted tunneling processes in proton displacement damage areas located near the device sidewalls.« less

Seeing the landscape for the trees: Metrics to guide riparian shade management in river catchments

NASA Astrophysics Data System (ADS)

Johnson, Matthew F.; Wilby, Robert L.

2015-05-01

Rising water temperature (Tw) due to anthropogenic climate change may have serious consequences for river ecosystems. Conservation and/or expansion of riparian shade could counter warming and buy time for ecosystems to adapt. However, sensitivity of river reaches to direct solar radiation is highly heterogeneous in space and time, so benefits of shading are also expected to be site specific. We use a network of high-resolution temperature measurements from two upland rivers in the UK, in conjunction with topographic shade modeling, to assess the relative significance of landscape and riparian shade to the thermal behavior of river reaches. Trees occupy 7% of the study catchments (comparable with the UK national average) yet shade covers 52% of the area and is concentrated along river corridors. Riparian shade is most beneficial for managing Tw at distances 5-20 km downstream from the source of the rivers where discharge is modest, flow is dominated by near-surface hydrological pathways, there is a wide floodplain with little landscape shade, and where cumulative solar exposure times are sufficient to affect Tw. For the rivers studied, we find that approximately 0.5 km of complete shade is necessary to off-set Tw by 1°C during July (the month with peak Tw) at a headwater site; whereas 1.1 km of shade is required 25 km downstream. Further research is needed to assess the integrated effect of future changes in air temperature, sunshine duration, direct solar radiation, and downward diffuse radiation on Tw to help tree planting schemes achieve intended outcomes.

Porcelain thickness and cement shade effects on the colour and translucency of porcelain veneering materials.

PubMed

Kürklü, Duygu; Azer, Shereen S; Yilmaz, Burak; Johnston, William M

2013-11-01

Purposes of this in vitro study include evaluating colour changes in combinations of feldspathic porcelain and cement resulting from different thicknesses of porcelain and different shades of composite luting agent, and evaluating relative translucency parameter (RTP) values. Porcelain discs of shade A1 at nominal thicknesses of 0.5 and 1.0mm were bonded to cements of three shades in a factorial design. Colours were calculated for CIE D65 Illuminant and Standard Human Observer on black, grey and white backings. A colour difference (CD) was calculated of each possible pair of different porcelain thickness values for the same cement shade and each possible pair of different cement shades for the same porcelain thickness. RTP was analyzed by ANOVA and selected pairwise comparisons. All mean CDs studied were perceptible and most were at or greater than the clinical acceptability threshold, with the notable exception that the mean CDs and their confidence limits were below the clinical acceptability threshold for a change in porcelain thickness when utilizing the Clear cement shade. Variation in the shade of the resin luting cement will result in CDs which are near or beyond clinical acceptability. A decrease in porcelain thickness did significantly increase RTP when bonded to the resin cement shades studied. Changes in porcelain thickness or cement shade may adversely affect basic aesthetic properties of these materials. Development of methods for analyzing aesthetic effects over greater ranges of thickness for these materials would improve the prognosis for using these materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

Tanning Shade Gradations of Models in Mainstream Fitness and Muscle Enthusiast Magazines: Implications for Skin Cancer Prevention in Men.

PubMed

Basch, Corey H; Hillyer, Grace Clarke; Ethan, Danna; Berdnik, Alyssa; Basch, Charles E

2015-07-01

Tanned skin has been associated with perceptions of fitness and social desirability. Portrayal of models in magazines may reflect and perpetuate these perceptions. Limited research has investigated tanning shade gradations of models in men's versus women's fitness and muscle enthusiast magazines. Such findings are relevant in light of increased incidence and prevalence of melanoma in the United States. This study evaluated and compared tanning shade gradations of adult Caucasian male and female model images in mainstream fitness and muscle enthusiast magazines. Sixty-nine U.S. magazine issues (spring and summer, 2013) were utilized. Two independent reviewers rated tanning shade gradations of adult Caucasian male and female model images on magazines' covers, advertisements, and feature articles. Shade gradations were assessed using stock photographs of Caucasian models with varying levels of tanned skin on an 8-shade scale. A total of 4,683 images were evaluated. Darkest tanning shades were found among males in muscle enthusiast magazines and lightest among females in women's mainstream fitness magazines. By gender, male model images were 54% more likely to portray a darker tanning shade. In this study, images in men's (vs. women's) fitness and muscle enthusiast magazines portrayed Caucasian models with darker skin shades. Despite these magazines' fitness-related messages, pro-tanning images may promote attitudes and behaviors associated with higher skin cancer risk. To date, this is the first study to explore tanning shades in men's magazines of these genres. Further research is necessary to identify effects of exposure to these images among male readers. © The Author(s) 2014.

[Effects of shading at different phases of grain-filling on wheat grain protein components contents and processing quality].

PubMed

Shi, Yu; Chen, Mao-xue; Yu, Zhen-wen; Xu, Zhen-zhu

2011-10-01

Taking three wheat cultivars Jimai 20 (strong gluten), Taishan 23 (medium gluten), and Ningmai 9 (weak gluten) as test materials, a field experiment was conducted to examine the effects of shading at different phases of grain-filling on the grain protein components contents and processing quality. Four treatments were installed, i. e., no shading (S0), shading at early grain-filling phase (from 0 day after anthesis (DAA) to 11 DAA; S1), shading at medium grain-filling phase (from 12 DAA to 23 DAA; S2), and shading at late grain-filling phase (from 24 DAA to 35 DAA; S3). No significant differences were observed in the grain albumin+globulin contents of the three cultivars among the four treatments. Shading increased the grain HMW-GS, LMW-GS, gluten, glutenin, and total protein contents of Jimai 20 and Taishan 23 significantly, and the increments were higher in treatment S2 than in other shading treatments. Treatments S2 and S3 increased the grain protein components contents of Ningmai 9 significantly. Comparing with the control, shading decreased the grain yield significantly, but increased the dough development time, dough stability time, and sedimentation volume, especially for treatment S2, which suggested that the wheat grain quality had a close relationship with the light intensity at medium phase of grain-filling. Overall, the regulation effect of shading at grain-filling stage on the wheat grain yield, grain protein components contents, and indices values of grain processing quality for the test cultivars was in the order of Jimai 20 > Taishan 23 > Ningmai 9.

Effects of shading on starch pasting characteristics of indica hybrid rice (Oryza sativa L.).

PubMed

Wang, Li; Deng, Fei; Ren, Wan-Jun; Yang, Wen-Yu

2013-01-01

Rice is an important staple crop throughout the world, but environmental stress like low-light conditions can negatively impact crop yield and quality. Using pot experiments and field experiments, we studied the effects of shading on starch pasting viscosity and starch content with six rice varieties for three years, using the Rapid Visco Analyser to measure starch pasting viscosity. Shading at different growth stages and in different rice varieties all affected the starch pasting characteristics of rice. The effects of shading on starch pasting viscosity at middle and later growth stages were greater than those at earlier stages. Shading enhanced breakdown but reduced hold viscosity and setback at tillering-elongation stage. Most pasting parameters changed significantly with shading after elongation stage. Furthermore, the responses of different varieties to shading differed markedly. The change scope of starch pasting viscosity in Dexiang 4103 was rather small after heading, while that in IIyou 498 and Gangyou 906 was small before heading. We observed clear tendencies in peak viscosity, breakdown, and pasting temperature of the five rice varieties with shading in 2010 and 2011. Correlation analysis indicated that the rice amylose content was negatively correlated with breakdown, but was positively correlated with setback. Based on our results, IIyou 498, Gangyou 906, and Dexiang 4103 had higher shade endurance, making these varieties most suitable for high-quality rice cultivation in low-light regions.

Effects of Shading on Starch Pasting Characteristics of Indica Hybrid Rice (Oryza sativa L.)

PubMed Central

Ren, Wan-Jun; Yang, Wen-Yu

2013-01-01

Rice is an important staple crop throughout the world, but environmental stress like low-light conditions can negatively impact crop yield and quality. Using pot experiments and field experiments, we studied the effects of shading on starch pasting viscosity and starch content with six rice varieties for three years, using the Rapid Visco Analyser to measure starch pasting viscosity. Shading at different growth stages and in different rice varieties all affected the starch pasting characteristics of rice. The effects of shading on starch pasting viscosity at middle and later growth stages were greater than those at earlier stages. Shading enhanced breakdown but reduced hold viscosity and setback at tillering-elongation stage. Most pasting parameters changed significantly with shading after elongation stage. Furthermore, the responses of different varieties to shading differed markedly. The change scope of starch pasting viscosity in Dexiang 4103 was rather small after heading, while that in IIyou 498 and Gangyou 906 was small before heading. We observed clear tendencies in peak viscosity, breakdown, and pasting temperature of the five rice varieties with shading in 2010 and 2011. Correlation analysis indicated that the rice amylose content was negatively correlated with breakdown, but was positively correlated with setback. Based on our results, IIyou 498, Gangyou 906, and Dexiang 4103 had higher shade endurance, making these varieties most suitable for high-quality rice cultivation in low-light regions. PMID:23861872

[Effects of soil moisture content and light intensity on the plant growth and leaf physiological characteristics of squash].

PubMed

Du, She-ni; Bai, Gang-shuan; Liang, Yin-li

2011-04-01

A pot experiment with artificial shading was conducted to study the effects of soil moisture content and light intensity on the plant growth and leaf physiological characteristics of squash variety "Jingyingyihao". Under all test soil moisture conditions, 30% shading promoted the growth of "Jingyingyihao", with the highest yield at 70% - 80% soil relative moisture contents. 70% shading inhibited plant growth severely, only flowering and not bearing fruits, no economic yield produced. In all treatments, there was a similar water consumption trend, i. e., both the daily and the total water consumption decreased with increasing shading and decreasing soil moisture content. Among all treatments, 30% shading and 70% - 80% soil relative moisture contents had the highest water use efficiency (2.36 kg mm(-1) hm(-2)) and water output rate (1.57 kg mm(-1) hm(-2)). The net photosynthetic rate, transpiration rate, stomatal conductance, and chlorophyll content of squash leaves decreased with increasing shading, whereas the intercellular CO2 concentration was in adverse. The leaf protective enzyme activity and proline content decreased with increasing shading, and the leaf MAD content decreased in the order of 70% shading, natural radiation, and 30% shading. Under the three light intensities, the change characteristics of squash leaf photosynthesis, protective enzyme activity, and proline and MAD contents differed with the increase of soil relative moisture content.

A 4MP high-dynamic-range, low-noise CMOS image sensor

NASA Astrophysics Data System (ADS)

Ma, Cheng; Liu, Yang; Li, Jing; Zhou, Quan; Chang, Yuchun; Wang, Xinyang

2015-03-01

In this paper we present a 4 Megapixel high dynamic range, low dark noise and dark current CMOS image sensor, which is ideal for high-end scientific and surveillance applications. The pixel design is based on a 4-T PPD structure. During the readout of the pixel array, signals are first amplified, and then feed to a low- power column-parallel ADC array which is already presented in [1]. Measurement results show that the sensor achieves a dynamic range of 96dB, a dark noise of 1.47e- at 24fps speed. The dark current is 0.15e-/pixel/s at -20oC.

Stream shading, summer streamflow and maximum water temperature following intense wildfire in headwater streams

Treesearch

Michael Amaranthus; Howard Jubas; David Arthur

1989-01-01

Adjacent headwater streams were monitored for postfire shade, summer streamflow and maximum water temperature following the 40,000 ha Silver Complex fire in southern Oregon. Average postfire shade (30 percent) for the three streams was considerably less than prefire shade (est.>90 percent). Dramatic increases in direct solar radiation resulted in large but variable...

Effects of street tree shade on asphalt concrete pavement performance

Treesearch

E.G. McPherson; J. Muchnick

2005-01-01

Forty-eight street segments were paired into 24 high-and low-shade pairs in Modesto, California, U.S. Field data were collected to calculate a Pavement Condition Index (PCI) and Tree Shade Index (TSI) for each segment. Statistical analyses found that greater PCI was associated with greater TSI, indicating that tree shade was partially responsible for reduced pavement...

An appraisal of the classic forest succession paradigm with the shade tolerance index.

PubMed

Lienard, Jean; Florescu, Ionut; Strigul, Nikolay

2015-01-01

In this paper we revisit the classic theory of forest succession that relates shade tolerance and species replacement and assess its validity to understand patch-mosaic patterns of forested ecosystems of the USA. We introduce a macroscopic parameter called the "shade tolerance index" and compare it to the classic continuum index in southern Wisconsin forests. We exemplify shade tolerance driven succession in White Pine-Eastern Hemlock forests using computer simulations and analyzing approximated chronosequence data from the USDA FIA forest inventory. We describe this parameter across the last 50 years in the ecoregions of mainland USA, and demonstrate that it does not correlate with the usual macroscopic characteristics of stand age, biomass, basal area, and biodiversity measures. We characterize the dynamics of shade tolerance index using transition matrices and delimit geographical areas based on the relevance of shade tolerance to explain forest succession. We conclude that shade tolerance driven succession is linked to climatic variables and can be considered as a primary driving factor of forest dynamics mostly in central-north and northeastern areas in the USA. Overall, the shade tolerance index constitutes a new quantitative approach that can be used to understand and predict succession of forested ecosystems and biogeographic patterns.

Comparison of shade matching by visual observation and an intraoral dental colorimeter.

PubMed

Li, Q; Wang, Y N

2007-11-01

The purpose of this study was to compare the applicability of two shade-matching approaches: Vintage Halo shade guide (visual method) and Shofu ShadeEye NCC colorimeter (instrumental method). Twenty participants' maxillary left central incisors were evaluated. Corresponding metal ceramic crowns were fabricated with each shade-matching approach. The colour distributions (L*, a* and b*) of the middle third region of each tooth and corresponding metal ceramic crowns were spectrophotometrically assessed. The colour difference (DeltaE) and colour distributions (DeltaL*, Deltaa* and Deltab*) between the tooth and the corresponding crowns were calculated. We found that the colour differences of both groups fell within the clinical unacceptable range (DeltaE > 2.75). Regarding DeltaE and the three colour distributions, no significant difference was found, expect for a* (P < 0.01). The shade matching difficulty degree was analysed through the agreements of visual shade selection. Within easy matching cases, the instrumental method achieved better results (P = 0.041). In conclusion, it is suggested that the reliability of shade matching can be ensured by neither the colorimeter nor the visual approach. However, the colorimeter can achieve better results within easy matching cases.

Response of Artemisia annua L. to shade and manure fertilizer application in lowland altitude

NASA Astrophysics Data System (ADS)

Permana, H. H.; Widyastuti, Y.; Samanhudi; Yunus, A.

2018-03-01

Artemisia is a plant producing artemisinin substance which is the main compound in the treatment of malaria. Artemisia comes from China, usually grows wild in native habitats in the plains with an altitude of 1,000-1,500 meters above the sea level. Artemisia development efforts in Indonesia hampered by limited land with the required altitude due to their competition with vegetable crops. Based on this reason, this research is conducted to observe the growth of artemisia planted in lowland with the help of shade and manure. This study aims to determine the level of shade and best manure on the growth of Artemisia. Research conducted at the Laboratory of the Faculty of Agriculture UNS Jumantono using nested design with two factors, shade as main factor and manure fertilizer as sub factor. The data analysis used F test with confidence level of 5%, if significant, then continued with DMRT (Duncan Multiple Range Test). The results showed the treatment of shade gave no difference in growth within 50% shade, 75% shade as well as without shade treatment. Goat manure fertilizer gave the highest result and able to increase plant height, number of branches, flower weight and root volume.

Applied photo interpretation for airbrush cartography

NASA Technical Reports Server (NTRS)

Inge, J. L.; Bridges, P. M.

1976-01-01

Lunar and planetary exploration has required the development of new techniques of cartographic portrayal. Conventional photo-interpretive methods employing size, shape, shadow, tone, pattern, and texture are applied to computer-processed satellite television images. Comparative judgements are affected by illumination, resolution, variations in surface coloration, and transmission or processing artifacts. The portrayal of tonal densities in a relief illustration is performed using a unique airbrush technique derived from hill-shading of contour maps. The control of tone and line quality is essential because the mid-gray to dark tone densities must be finalized prior to the addition of highlights to the drawing. This is done with an electric eraser until the drawing is completed. The drawing density is controlled with a reflectance-reading densitometer to meet certain density guidelines. The versatility of planetary photo-interpretive methods for airbrushed map portrayals is demonstrated by the application of these techniques to the synthesis of nonrelief data.

Smart photovoltaics based on dye-sensitized solar cells using photochromic spiropyran derivatives as photosensitizers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Shengbo; Ting, Hungkit; Ma, Yingzhuang

2015-05-15

In this paper, smart photovoltaic (SPV) devices, integrating both functions of solar cells and smart windows, was fabricated based on dye-sensitized solar cells using photochromic spiropyran derivatives SIBT as photosensitizers. SPV devices have self-regulated power conversion efficiency (PCE) and light transmission responding to the incident spectra due to the photoisomerization of SIBT. SIBT isomerize from closed-ring form to open-ring form under UV illumination, accompanied with enhanced visible light absorption and electron delocalization. Therefore, increased PCE and absorption in SPV devices were observed under UV treatment and the devices can be restored gradually to the initial status when kept in dark.more » The SPV devices have self-regulation of PCE and sunlight transmission responding to the changing sun spectra in different times of a day, providing a proper energy usage and a better sun-shading.« less

Dynamics of Photosystem II and Its Light Harvesting System in Response to Light Changes in the Halotolerant Alga Dunaliella salina1

PubMed Central

Pick, Uri; Gounaris, Kleoniki; Barber, James

1987-01-01

A photosystem two (PSII) core complex consisting of five major polypeptides (47, 40, 32, 30, and 10 kilodaltons) and a light harvesting chlorophyll a/b complex (LHC-2) have been isolated from the halotolerant alga Dunaliella salina. The chlorophyll and polypeptide composition of both complexes were compared in illuminated and dark-adapted cultures. Dark adaptation is accompanied by a decrease in the chlorophyll a to chlorophyll b (Chl a/Chl b) ratio of intact thylakoids without any change in total chlorophyll. These changes occur with a half-time of 3 hours and are reversed upon reillumination. Analyses of PSII enriched membrane fragments suggest that the decrease in the Chl a/Chl b is due partly to an increase in the Chl b content of LHC-2 and partly to changes in the relative levels of the two complexes. Apparently during dark adaptation there is: (a) a net synthesis of chlorophyll b, (b) removal of PSII core complexes resulting in a 2-fold drop in the PSII cores to LHC-2 chlorophyll ratio. These changes should dramatically increase the light harvesting capacity of the remaining PSII reaction centers. Presumably this adjustment of antenna size and composition is a physiological mechanism necessary for responding to shade conditions. Also detected, using 32P, are light-induced phosphorylation of the LHC-2 (consistent with the ability to undergo State transitions) and of the 40 and 30 kilodalton subunits of the PSII core complex. These observations indicate that additional mechanisms may also exist to help optimize the interception of quanta during rapid changes in illumination conditions. Images Fig. 4 PMID:16665656

Figures of merit for present and future dark energy probes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mortonson, Michael J.; Huterer, Dragan; Hu, Wayne

2010-09-15

We compare current and forecasted constraints on dynamical dark energy models from Type Ia supernovae and the cosmic microwave background using figures of merit based on the volume of the allowed dark energy parameter space. For a two-parameter dark energy equation of state that varies linearly with the scale factor, and assuming a flat universe, the area of the error ellipse can be reduced by a factor of {approx}10 relative to current constraints by future space-based supernova data and CMB measurements from the Planck satellite. If the dark energy equation of state is described by a more general basis ofmore » principal components, the expected improvement in volume-based figures of merit is much greater. While the forecasted precision for any single parameter is only a factor of 2-5 smaller than current uncertainties, the constraints on dark energy models bounded by -1{<=}w{<=}1 improve for approximately 6 independent dark energy parameters resulting in a reduction of the total allowed volume of principal component parameter space by a factor of {approx}100. Typical quintessence models can be adequately described by just 2-3 of these parameters even given the precision of future data, leading to a more modest but still significant improvement. In addition to advances in supernova and CMB data, percent-level measurement of absolute distance and/or the expansion rate is required to ensure that dark energy constraints remain robust to variations in spatial curvature.« less

Reversing legacy effects in the understory of an oak-dominated forest

Treesearch

Melissa Thomas-Van Gundy; James Rentch; Mary Beth Adams; Walter Carson

2014-01-01

Current forests developed under conditions different from original forests, with higher deer densities, reduced fire frequency, denser canopies, and smaller canopy gaps. These alterations have led to understories dominated by species simultaneously browse tolerant, shade tolerant, and fire sensitive leading to difficulties in the regeneration of oak species (...

Raman Spectroscopic Online Investigation of Respiratory Quotients in Pinus Sylvestris and Picea Abies during Drought and Shading

NASA Astrophysics Data System (ADS)

Hanf, S.; Fischer, S.; Hartmann, H.; Trumbore, S.; Popp, J.; Frosch, T.

2014-12-01

Drought and heat waves have been linked to forest mortality event across the globe. The underlying physiological processes are still not elucidated but both tree carbon and water relations have been identified as the driving forces. While studies on tree hydraulics are straightforward, studies on the tree carbon balance are not. For example, the use of different carbon compounds for maintenance respiration during drought cannot be assessed with measurements of carbon pools but requires real-time analyses of respiration stoichiometry. However, so far there were no technical solutions for such applications. Here we introduce cavity-enhanced Raman spectrometry (CERS) for simultaneous real-time monitoring of O2 and CO2 and rapid and continuous quantification of dark respiration rates and the respiratory quotient (RQ), i.e. the ratio of CO2 produced over O2 consumed during respiration. This ratio indicates the proportions of different substrates (carbohydrates [COH], lipids, proteins) used during respiration and allows fundamental insights into tree physiology. CERS combines high temporal resolution with a high dynamic concentration range for all important gases, ranging from few ppm to 100 vol. % with a single measurement every few seconds. The respiration analysis of tree branches was performed in a closed chamber for two species of different drought tolerance, Pinus sylvestris and Picea abies. We applied not only drought but also a shading treatment because both cause reductions in carbon assimilation rates but have different effects on tree hydraulics. Declines in RQ during shading in both species indicate a switch from pure COH metabolism to a mixture of COH, lipids and proteins. During drought such declines occurred only in the drought-tolerant pine but not in spruce and the underlying more dynamic carbon use strategy in pine may provide a physiological basis for its drought tolerance, more detailed investigation still pending. Our study highlights the suitability of CERS for applications in plant ecophysiology. This technology can contribute to significant advances in research on the causes and mechanisms of tree and forest mortality.

Derivation of planetary topography using multi-image shape-from-shading

USGS Publications Warehouse

Lohse, V.; Heipke, C.; Kirk, R.L.

2006-01-01

In many cases, the derivation of high-resolution digital terrain models (DTMs) from planetary surfaces using conventional digital image matching is a problem. The matching methods need at least one stereo pair of images with sufficient texture. However, many space missions provide only a few stereo images and planetary surfaces often possess insufficient texture. This paper describes a method for the generation of high-resolution DTMs from planetary surfaces, which has the potential to overcome the described problem. The suggested method, developed by our group, is based on shape-from-shading using an arbitrary number of digital optical images, and is termed "multi-image shape-from-shading" (MI-SFS). The paper contains an explanation of the theory of MI-SFS, followed by a presentation of current results, which were obtained using images from NASA's lunar mission Clementine, and constitute the first practical application with our method using extraterrestrial imagery. The lunar surface is reconstructed under the assumption of different kinds of reflectance models (e.g. Lommel-Seeliger and Lambert). The represented results show that the derivation of a high-resolution DTM of real digital planetary images by means of MI-SFS is feasible. ?? 2006 Elsevier Ltd. All rights reserved.

Dynamics of domain coverage of the protein sequence universe

PubMed Central

2012-01-01

Background The currently known protein sequence space consists of millions of sequences in public databases and is rapidly expanding. Assigning sequences to families leads to a better understanding of protein function and the nature of the protein universe. However, a large portion of the current protein space remains unassigned and is referred to as its “dark matter”. Results Here we suggest that true size of “dark matter” is much larger than stated by current definitions. We propose an approach to reducing the size of “dark matter” by identifying and subtracting regions in protein sequences that are not likely to contain any domain. Conclusions Recent improvements in computational domain modeling result in a decrease, albeit slowly, in the relative size of “dark matter”; however, its absolute size increases substantially with the growth of sequence data. PMID:23157439

Effects of adsorbed pyridine derivatives and ultrathin atomic-layer-deposited alumina coatings on the conduction band-edge energy of TiO2 and on redox-shuttle-derived dark currents.

PubMed

Katz, Michael J; Vermeer, Michael J D; Farha, Omar K; Pellin, Michael J; Hupp, Joseph T

2013-01-15

Both the adsorption of t-butylpyridine and the atomic-layer deposition of ultrathin conformal coatings of insulators (such as alumina) are known to boost open-circuit photovoltages substantially for dye-sensitized solar cells. One attractive interpretation is that these modifiers significantly shift the conduction-edge energy of the electrode, thereby shifting the onset potential for dark current arising from the interception of injected electrons by solution-phase redox shuttle components such as Co(phenanthroline)(3)(3+) and triiodide. For standard, high-area, nanoporous photoelectrodes, band-edge energies are difficult to measure directly. In contrast, for flat electrodes they are readily accessible from Mott-Schottky analyses of impedance data. Using such electrodes (specifically TiO(2)), we find that neither organic nor inorganic electrode-surface modifiers shift the conduction-band-edge energy sufficiently to account fully for the beneficial effects on electrode behavior (i.e., the suppression of dark current). Additional experiments reveal that the efficacy of ultrathin coatings of Al(2)O(3) arises chiefly from the passivation of redox-catalytic surface states. In contrast, adsorbed t-butylpyridine appears to suppress dark currents mainly by physically blocking access of shuttle molecules to the electrode surface. Studies with other derivatives of pyridine, including sterically and/or electronically diverse derivatives, show that heterocycle adsorption and the concomitant suppression of dark current does not require the coordination of surface Ti(IV) or Al(III) atoms. Notably, the favorable (i.e., negative) shifts in onset potential for the flow of dark current engendered by organic and inorganic surface modifiers are additive. Furthermore, they appear to be largely insensitive to the identity of shuttle molecules.

The effects of providing portable shade at pasture on dairy cow behavior and physiology.

PubMed

Palacio, S; Bergeron, R; Lachance, S; Vasseur, E

2015-09-01

Access to pasture has advantages for cows such as reduced lameness and improved udder health, but also may expose cows to stressors such as extreme heat. The objective of this study was to understand how portable shade affected physiological and behavioral responses of pastured dairy cows in a Canadian summer. Over 8wk, a total of 24 lactating Holstein cows were separated into 2 treatments, one with access to shade and a control without access to shade. The cows were pastured in groups of 4, with 3 field sections per treatment. Instantaneous scan sampling of behaviors (drinking, lying, grazing, other) performed in the shade or not were recorded every 5min for 3h/d during the hottest part of the day (peak hours: 1130-1530h) 3d/wk. Ambient temperature, humidity, and vaginal temperature were recorded at 10-min intervals. Daily milk production was also recorded. Differences between treatments by week were analyzed using the generalized linear mixed model with group as random effect and treatment as fixed effect. Cows with shade access were observed at the water trough up to 6.42 times less and lying down up to 1.75 times more. Cows with shade access grazed up to 1.5 times more but only when the temperature-humidity index was above their comfort threshold (≥72) during the hottest part of the day (wk 2). Cows sought shade when it was made available, but spent less than half of their time observed (%) in the shade (40.8±4.67) with the exception of wk 2 when most of the time was spent under the shade (74.3±4.77). Daily lying time was highest during peak hours for cows with shade access. However, no overall difference in total lying time between the 2 treatments was observed. No differences were found in vaginal temperature or milk production between treatments with the exception of wk 1 for daily milk production, which was higher for cows in the control treatment. In conclusion, cows sought shade when it was provided at pasture, whereas cows without access to shade seemed to alter their behavior to cope with heat stress, as seen from the lack of physiological differences between treatments. The results indicate that providing cows with access to pasture under a temperate climate does not seem to have any detrimental physiological or production effects and providing them with shade can potentially decrease production costs and help with water conservation strategies as fewer cows were observed at the water when shade was provided. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The effect of irradiance on the carbon balance and tissue characteristics of five herbaceous species differing in shade-tolerance

PubMed Central

Pons, Thijs L.; Poorter, Hendrik

2014-01-01

The carbon balance is defined here as the partitioning of daily whole-plant gross CO2 assimilation (A) in C available for growth and C required for respiration (R). A scales positively with growth irradiance and there is evidence for an irradiance dependence of R as well. Here we ask if R as a fraction of A is also irradiance dependent, whether there are systematic differences in C-balance between shade-tolerant and shade-intolerant species, and what the causes could be. Growth, gas exchange, chemical composition and leaf structure were analyzed for two shade-tolerant and three shade-intolerant herbaceous species that were hydroponically grown in a growth room at five irradiances from 20 μmol m−2 s−1 (1.2 mol m−2 day−1) to 500 μmol m−2 s−1 (30 mol m−2 day−1). Growth analysis showed little difference between species in unit leaf rate (dry mass increase per unit leaf area) at low irradiance, but lower rates for the shade-tolerant species at high irradiance, mainly as a result of their lower light-saturated rate of photosynthesis. This resulted in lower relative growth rates in these conditions. Daily whole-plant R scaled with A in a very tight manner, giving a remarkably constant R/A ratio of around 0.3 for all but the lowest irradiance. Although some shade-intolerant species showed tendencies toward a higher R/A and inefficiencies in terms of carbon and nitrogen investment in their leaves, no conclusive evidence was found for systematic differences in C-balance between the shade-tolerant and intolerant species at the lowest irradiance. Leaf tissue of the shade-tolerant species was characterized by high dry matter percentages, C-concentration and construction costs, which could be associated with a better defense in shade environments where leaf longevity matters. We conclude that shade-intolerant species have a competitive advantage at high irradiance due to superior potential growth rates, but that shade-tolerance is not necessarily associated with a better C-balance at low irradiance. Under those conditions tolerance to other stresses is probably more important for the performance of shade-tolerant species. PMID:24550922

75 FR 52724 - Procurement List Additions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-27

...: 8405-00-FAB-0201--Man's, S/S, Air Force Shade 1550, Size 13\\1/ 2\\ NSN: 8405-00-FAB-0202--Man's, S/S, Air Force Shade 1550, Size 14 NSN: 8405-00-FAB-0203--Man's, S/S, Air Force Shade 1550, Size 14 \\1/ 2\\ NSN: 8405-00-FAB-0204--Man's, S/S, Air Force Shade 1550, Size 15 NSN: 8405-00-FAB-0212--Man's, S/S...

Ranking the shade tolerance of forty-five candidate groundcovers for agroforestry plantings

Treesearch

J.W. Van Sambeek; N.E. Navarrete-Tindall; H.E. Garrett; C.-H. Lin; R.L. McGraw; D.C. Wallace

2007-01-01

Several large-scale screening trials evaluating native and introduced herbaceous ground covers have been conducted in the last half century. Most trials have used shade cloth to evaluate growth of potted plants under moderate shade (45 to 55 percent of full sunlight) similar to what might be found in many agroforestry practices and heavy shade (20 to 30 percent of full...

An appraisal of the classic forest succession paradigm with the shade tolerance index

Treesearch

Jean Lienard; Ionut Florescu; Nikolay Strigul

2015-01-01

We revisit the classic theory of forest succession that relates shade tolerance and species replacement and assess its validity to understand patch-mosaic patterns of forested ecosystems of the USA. We introduce a macroscopic parameter called the “shade tolerance index” and compare it to the classic continuum index in southern Wisconsin forests. We exemplify shade...

Numerical Device Modeling, Analysis, and Optimization of Extended-SWIR HgCdTe Infrared Detectors

NASA Astrophysics Data System (ADS)

Schuster, J.; DeWames, R. E.; DeCuir, E. A.; Bellotti, E.; Dhar, N.; Wijewarnasuriya, P. S.

2016-09-01

Imaging in the extended short-wavelength infrared (eSWIR) spectral band (1.7-3.0 μm) for astronomy applications is an area of significant interest. However, these applications require infrared detectors with extremely low dark current (less than 0.01 electrons per pixel per second for certain applications). In these detectors, sources of dark current that may limit the overall system performance are fundamental and/or defect-related mechanisms. Non-optimized growth/device processing may present material point defects within the HgCdTe bandgap leading to Shockley-Read-Hall dominated dark current. While realizing contributions to the dark current from only fundamental mechanisms should be the goal for attaining optimal device performance, it may not be readily feasible with current technology and/or resources. In this regard, the U.S. Army Research Laboratory performed physics-based, two- and three-dimensional numerical modeling of HgCdTe photovoltaic infrared detectors designed for operation in the eSWIR spectral band. The underlying impetus for this capability and study originates with a desire to reach fundamental performance limits via intelligent device design.

Reliability of visual and instrumental color matching.

PubMed

Igiel, Christopher; Lehmann, Karl Martin; Ghinea, Razvan; Weyhrauch, Michael; Hangx, Ysbrand; Scheller, Herbert; Paravina, Rade D

2017-09-01

The aim of this investigation was to evaluate intra-rater and inter-rater reliability of visual and instrumental shade matching. Forty individuals with normal color perception participated in this study. The right maxillary central incisor of a teaching model was prepared and restored with 10 feldspathic all-ceramic crowns of different shades. A shade matching session consisted of the observer (rater) visually selecting the best match by using VITA classical A1-D4 (VC) and VITA Toothguide 3D Master (3D) shade guides and the VITA Easyshade Advance intraoral spectrophotometer (ES) to obtain both VC and 3D matches. Three shade matching sessions were held with 4 to 6 weeks between sessions. Intra-rater reliability was assessed based on the percentage of agreement for the three sessions for the same observer, whereas the inter-rater reliability was calculated as mean percentage of agreement between different observers. The Fleiss' Kappa statistical analysis was used to evaluate visual inter-rater reliability. The mean intra-rater reliability for the visual shade selection was 64(11) for VC and 48(10) for 3D. The corresponding ES values were 96(4) for both VC and 3D. The percentages of observers who matched the same shade with VC and 3D were 55(10) and 43(12), respectively, while corresponding ES values were 88(8) for VC and 92(4) for 3D. The results for visual shade matching exhibited a high to moderate level of inconsistency for both intra-rater and inter-rater comparisons. The VITA Easyshade Advance intraoral spectrophotometer exhibited significantly better reliability compared with visual shade selection. This study evaluates the ability of observers to consistently match the same shade visually and with a dental spectrophotometer in different sessions. The intra-rater and inter-rater reliability (agreement of repeated shade matching) of visual and instrumental tooth color matching strongly suggest the use of color matching instruments as a supplementary tool in everyday dental practice to enhance the esthetic outcome. © 2017 Wiley Periodicals, Inc.

Effect of abutment shade, ceramic thickness, and coping type on the final shade of zirconia all-ceramic restorations: in vitro study of color masking ability

PubMed Central

Oh, Seon-Hee

2015-01-01

PURPOSE The aim of the study was to evaluate the effect of abutment shade, ceramic thickness, and coping type on the final shade of zirconia all-ceramic restorations. MATERIALS AND METHODS Three different types of disk-shaped zirconia coping specimens (Lava, Cercon, Zirkonzahn: ø10 mm × 0.4 mm) were fabricated and veneered with IPS e.max Press Ceram (shade A2), for total thicknesses of 1 and 1.5 mm. A total of sixty zirconia restoration specimens were divided into six groups based on their coping types and thicknesses. The abutment specimens (ø10 mm × 7 mm) were prepared with gold alloy, base metal (nickel-chromium) alloy, and four different shades (A1, A2, A3, A4) of composite resins. The average L*, a*, b* values of the zirconia specimens on the six abutment specimens were measured with a dental colorimeter, and the statistical significance in the effects of three variables was analyzed by using repeated measures analysis of variance (α=.05).The average shade difference (ΔE) values of the zirconia specimens between the A2 composite resin abutment and other abutments were also evaluated. RESULTS The effects of zirconia specimen thickness (P<.001), abutment shade (P<.001), and type of zirconia copings (P<.003) on the final shade of the zirconia restorations were significant. The average ΔE value of Lava specimens (1 mm) between the A2 composite resin and gold alloy abutments was higher (close to the acceptability threshold of 5.5 ΔE) than th ose between the A2 composite resin and other abutments. CONCLUSION This in-vitro study demonstrated that abutment shade, ceramic thickness, and coping type affected the resulting shade of zirconia restorations. PMID:26576252

The effect of enamel porcelain thickness on color and the ability of a shade guide to prescribe chroma.

PubMed

Jarad, F D; Moss, B W; Youngson, C C; Russell, M D

2007-04-01

To test the null hypothesis that there is no color change when enamel porcelain thickness is changed and to evaluate the ability of a shade guide to prescribe chroma. Three shades (3M1, 3M2 and 3M3) were selected from a Vitapan 3D master shade guide. Five disk specimens were prepared for each shade, consisting of three layers (opacious dentin, dentin and enamel) at thicknesses of 0.6, 0.8 and 0.6mm, respectively. The color of each disk was measured using a spectrophotometer. Enamel porcelain was reduced in thickness to 0.3mm and porcelain disks were remeasured. Reducing the enamel thickness of porcelain disk specimens significantly increased L) (p<0.05), b*, metric chroma and hue angle (p<0.001). For the three shades studied (3M1, 3M2 and 3M3) L* values were not significantly different (p>0.05) and chroma increased for 3M1 with the lowest chroma to 3M3 with the highest chroma, which is in line with the shade guide specifications. Although statistically significant (p<0.001) changes in hue angle between the three shades were small (less than 3 degrees overall). The difference in chroma between the three shades 3M1, 3M2 and 3M3 was greatest for the thin enamel layer than the thick enamel layer. A change in enamel thickness from 0.6 to 0.3mm resulted in a three-unit change in L* and metric chroma and a 4 degrees change in hue angle. A change in enamel porcelain thickness will have a greater effect on higher chromatic shades than those with lower chroma. The ability of the shade guide to prescribe chroma was demonstrated but this could be offset by an anomalous enamel thickness.

Searching for dark matter-dark energy interactions: Going beyond the conformal case

NASA Astrophysics Data System (ADS)

van de Bruck, Carsten; Mifsud, Jurgen

2018-01-01

We consider several cosmological models which allow for nongravitational direct couplings between dark matter and dark energy. The distinguishing cosmological features of these couplings can be probed by current cosmological observations, thus enabling us to place constraints on these specific interactions which are composed of the conformal and disformal coupling functions. We perform a global analysis in order to independently constrain the conformal, disformal, and mixed interactions between dark matter and dark energy by combining current data from: Planck observations of the cosmic microwave background radiation anisotropies, a combination of measurements of baryon acoustic oscillations, a supernova type Ia sample, a compilation of Hubble parameter measurements estimated from the cosmic chronometers approach, direct measurements of the expansion rate of the Universe today, and a compilation of growth of structure measurements. We find that in these coupled dark-energy models, the influence of the local value of the Hubble constant does not significantly alter the inferred constraints when we consider joint analyses that include all cosmological probes. Moreover, the parameter constraints are remarkably improved with the inclusion of the growth of structure data set measurements. We find no compelling evidence for an interaction within the dark sector of the Universe.

Compositional changes in 'Bartlett' pear ( Pyrus communis L.) cell wall polysaccharides as affected by sunlight conditions.

PubMed

Raffo, María D; Ponce, Nora M A; Sozzi, Gabriel O; Vicente, Ariel R; Stortz, Carlos A

2011-11-23

Preharvest conditions can have a great impact on fruit quality attributes and postharvest responses. Firmness is an important quality attribute in pear, and excessive softening increases susceptibility to bruising and decay, thus limiting fruit postharvest life. Textural characteristics of fruits are determined at least in part by cell wall structure and disassembly. Few studies have analyzed the influence of fruit preharvest environment in softening, cell wall composition, and degradation. In the current work 'Bartlett' pears grown either facing the sun (S) or in the shade (H) were harvested and stored for 13 days at 20 °C. An evaluation of fruit soluble solids, acidity, color, starch degradation, firmness, cell wall yield, pectin and matrix glycan solubilization, depolymerization, and monosaccharide composition was carried out. Sun-exposed pears showed more advanced color development and similar levels of starch degradation, sugars, and acids than shaded fruit. Sunlight-grown pears were at harvest firmer than shade-grown pears. Both fruit groups softened during storage at 20 °C, but even after ripening, sun-exposed pears remained firmer. Sunlight exposure did not have a great impact on pectin molecular weight. Instead, at harvest a higher proportion of water-solubilized uronic acids and alkali-solubilized neutral sugars and a larger mean molecular size of tightly bound glycans was found in sun-exposed pears. During ripening cell wall catabolism took place in both sun- and shade-grown pears, but pectin solubilization was clearly delayed in sun-exposed fruit. This was associated with decreased removal of RG I-arabinan side chains rather than with reduced depolymerization.

Health impacts of ultraviolet radiation in urban ecosystems: a review

NASA Astrophysics Data System (ADS)

Heisler, Gordon M.

2005-08-01

This paper explores the literature on ultraviolet irradiance (UV) in urban ecosystems with respect to the likely effects on human health. The focus was the question of whether the health effects of UV radiation should be included in planning of landscape elements such as trees and shading structures. In examining the literature, special attention was given to seeking information on the question of whether it is important that shade be provided for elementary school play areas, and if so, how should it be accomplished? Before such practical questions could be dealt with, it became obvious that answers to several pertinent secondary questions had to be sought. Foremost of these was, what are the negative and positive health effects of UV exposure? Recent epidemiological findings of apparent benefits of sunlight because of vitamin-D photosynthesis and resulting anti-cancer effects make this highly relevant. Another basic question is that of trends in ozone depletion, which leads to interesting questions of long-term trends, short-term extremes, and urban influences on UV irradiance. A host of these and other pertinent questions, such as, "What is the relationship between climate of a location and dress," i.e., "How much exposure will people receive during time spent outdoors?" require much more study. Judging from current knowledge of typical spectra of solar radiation in tree shade and the difference between the action spectra for vitamin D synthesis and erythema in human skin, exposure to solar radiation in tree shade for a short period of time can be somewhat more beneficial for vitamin D synthesis and regulation than detrimental in producing sunburn.

The shady side of solar protection.

PubMed

Parsons, P G; Neale, R; Wolski, P; Green, A

1998-04-06

To determine the value of shade in protecting humans from solar ultraviolet (UV) radiation. Measurement with photometers of protection factors for ultraviolet B radiation (UVB) and for total solar radiation for different types of trees and other structures during the summer months (1995-1997) in south-east Queensland. (The protection ratio is the ratio of the intensity of UVB or total solar radiation in direct sunlight to that in shade.) For summer sun at midday, the mean (SD) UV protection ratio for the shade of trees (n = 65) was 4.21 (1.36) on a horizontal surface and 1.33 (0.30) on a vertical surface. In contrast, the mean (SD) protection ratio for total solar energy (primarily infrared) was much higher (12.1 [1.4]). Trees common in recreational areas in Australia (eucalypts: UV protection ratio, 3.52 [0.79]; Norfolk Island pines: UV protection ratio, 3.72 [0.98]) offered reduced protection compared with trees with more dense foliage (UV protection ratio, 5.48 [1.44]). Over a whole day, measurement of shade by trees and other structures showed that the UV protection ratio was lower in the morning and afternoon. Shade from awnings, buildings and hats gave similar results to those for trees. Both at midday and over a whole day satisfactory protection (UV protection ratio > 15) was obtained only in shade which eliminated exposure to the sky as well as to direct sunlight; for example, in thickly wooded areas and under low, widely overhanging structures. Most forms of shade, while useful, offer people insufficient protection from solar UV. A fair-skinned person sheltering under a tree could suffer sunburn after less than one hour. There is a need for appropriate design of structural shade, use of other solar protection measures in conjunction with shade, and research on behavioural responses to shade.

Accurate shade image matching by using a smartphone camera.

PubMed

Tam, Weng-Kong; Lee, Hsi-Jian

2017-04-01

Dental shade matching by using digital images may be feasible when suitable color features are properly manipulated. Separating the color features into feature spaces facilitates favorable matching. We propose using support vector machines (SVM), which are outstanding classifiers, in shade classification. A total of 1300 shade tab images were captured using a smartphone camera with auto-mode settings and no flash. The images were shot at angled distances of 14-20cm from a shade guide at a clinic equipped with light tubes that produced a 4000K color temperature. The Group 1 samples comprised 1040 tab images, for which the shade guide was randomly positioned in the clinic, and the Group 2 samples comprised 260 tab images, for which the shade guide had a fixed position in the clinic. Rectangular content was cropped manually on each shade tab image and further divided into 10×2 blocks. The color features extracted from the blocks were described using a feature vector. The feature vectors in each group underwent SVM training and classification by using the "leave-one-out" strategy. The top one and three accuracies of Group 1 were 0.86 and 0.98, respectively, and those of Group 2 were 0.97 and 1.00, respectively. This study provides a feasible technique for dental shade classification that uses the camera of a mobile device. The findings reveal that the proposed SVM classification might outperform the shade-matching results of previous studies that have performed similarity measurements of ΔE levels or used an S, a*, b* feature set. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Shade tree diversity and aboveground carbon stocks in Theobroma cacao agroforestry systems: implications for REDD+ implementation in a West African cacao landscape.

PubMed

Dawoe, Evans; Asante, Winston; Acheampong, Emmanuel; Bosu, Paul

2016-12-01

The promotion of cacao agroforestry is one of the ways of diversifying farmer income and creating incentives through their inclusion in REDD+ interventions. We estimated the aboveground carbon stocks in cacao and shade trees, determined the floristic diversity of shade trees and explored the possibility of implementing REDD+ interventions in cacao landscapes. Using replicated multi-site transect approach, data were collected from nine 1-ha plots established on 5 km long transects in ten cacao growing districts in Ghana West Africa. Biomass of cacao and shade trees was determined using allometric equations. One thousand four hundred and one (1401) shade trees comprising 109 species from 33 families were recorded. Total number of species ranged from 34 to 49. Newbouldia laevis (Bignoniacea) was the most frequently occurring specie and constituted 43.2 % of all shade trees. The most predominant families were Sterculiaceae and Moraceae (10 species each), followed by Meliaceae and Mimosaceae (8 species each) and Caesalpiniacaea (6 species). Shannon diversity indices (H', H max and J') and species richness were low compared to other similar studies. Shade tree densities ranged from 16.2 ± 3.0 to 22.8 ± 1.7 stems ha -1 and differed significantly between sites. Carbon stocks of shade trees differed between sites but were similar in cacao trees. The average C stock in cacao trees was 7.45 ± 0.41 Mg C ha -1 compared with 8.32 ± 1.15 Mg C ha -1 in the shade trees. Cacao landscapes in Ghana have the potential of contributing to forest carbon stocks enhancement by increasing the stocking density of shade trees to recommended levels.

A Custom Made Intrinsic Silicone Shade Guide for Indian Population

PubMed Central

Behanam, Mohammed; Ahila, S.C.; Jei, J. Brintha

2016-01-01

Introduction Replication of natural skin colour in maxillofacial prosthesis has been traditionally done using trial and error method, as concrete shade guides are unavailable till date. Hence a novel custom made intrinsic silicone shade guide has been attempted for Indian population. Aim Reconstruction of maxillofacial defects is challenging, as achieving an aesthetic result is not always easy. A concoction of a novel intrinsic silicone shade guide was contemplated for the study and its reproducibility in clinical practice was analysed. Materials and Methods Medical grade room temperature vulcanising silicone was used for the fabrication of shade tabs. The shade guide consisted of three main groups I, II and III which were divided based upon the hues yellow, red and blue respectively. Five distinct intrinsic pigments were added in definite proportions to subdivide each group of different values from lighter to darker shades. A total number of 15 circular shade tabs comprised the guide. To validate the usage of the guide, visual assessment of colour matching was done by four investigators to investigate the consent of perfect colour correspondence. Data was statistically analysed using kappa coefficients. Results The kappa values were found to be 0.47 to 0.78 for yellow based group I, 0.13 to 0.65 for red based group II, and 0.07 to 0.36 for blue based group III. This revealed that the shade tabs of yellow and red based hues matched well and showed a statistically good colour matching. Conclusion This intrinsic silicone shade guide can be effectively utilised for fabrication of maxillofacial prosthesis with silicone in Indian population. A transparent colour formula with definite proportioning of intrinsic pigments is provided for obtaining an aesthetic match to skin tone. PMID:27190946

Proposal for Axion Dark Matter Detection Using an L C Circuit

DOE PAGES

Sikivie, P.; Sullivan, N.; Tanner, D. B.

2014-03-01

Here, we show that dark matter axions cause an oscillating electric current to flow along magnetic field lines. The oscillating current induced in a strong magnetic field B → 0 produces a small magnetic field B → a. We propose to amplify and detect B → a using a cooled LC circuit and a very sensitive magnetometer. This appears to be a suitable approach to searching for axion dark matter in the 10 –7 to 10 –9 eV mass range.

Comparison of dark energy models: A perspective from the latest observational data

NASA Astrophysics Data System (ADS)

Li, Miao; Li, Xiaodong; Zhang, Xin

2010-09-01

We compare some popular dark energy models under the assumption of a flat universe by using the latest observational data including the type Ia supernovae Constitution compilation, the baryon acoustic oscillation measurement from the Sloan Digital Sky Survey, the cosmic microwave background measurement given by the seven-year Wilkinson Microwave Anisotropy Probe observations and the determination of H 0 from the Hubble Space Telescope. Model comparison statistics such as the Bayesian and Akaike information criteria are applied to assess the worth of the models. These statistics favor models that give a good fit with fewer parameters. Based on this analysis, we find that the simplest cosmological constant model that has only one free parameter is still preferred by the current data. For other dynamical dark energy models, we find that some of them, such as the α dark energy, constant w, generalized Chaplygin gas, Chevalliear-Polarski-Linder parametrization, and holographic dark energy models, can provide good fits to the current data, and three of them, namely, the Ricci dark energy, agegraphic dark energy, and Dvali-Gabadadze-Porrati models, are clearly disfavored by the data.

Automated analysis of hypocotyl growth dynamics during shade avoidance in Arabidopsis.

PubMed

Cole, Benjamin; Kay, Steve A; Chory, Joanne

2011-03-01

Plants that are adapted to environments where light is abundant are especially sensitive to competition for light from neighboring vegetation. As a result, these plants initiate a series of changes known as the shade avoidance syndrome, during which plants elongate their stems and petioles at the expense of leaf development. Although the developmental outcomes of exposure to prolonged shade are known, the signaling dynamics during the initial exposure of seedlings to shade is less well studied. Here, we report the development of a new software-based tool, called HyDE (Hypocotyl Determining Engine) to measure hypocotyl lengths of time-resolved image stacks of Arabidopsis wild-type and mutant seedlings. We show that Arabidopsis grows rapidly in response to the shade stimulus, with measurable growth after just 45 min shade exposure. Similar to other mustard species, this growth response occurs in multiple distinct phases, including two phases of rapid growth and one phase of slower growth. Using mutants affected in shade avoidance phenotypes, we demonstrate that most of this early growth requires new auxin biosynthesis via the indole-3-pyruvate pathway. When activity of this pathway is reduced, the first phase of elongation growth is absent, and this is correlated with reduced activity of auxin-regulated genes. Finally, we show that varying shade intensity and duration can affect the shape and magnitude of the growth response, indicating a broad range of the elongation response to shade. © 2011 The Authors. The Plant Journal © 2011 Blackwell Publishing Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Zhenyu, E-mail: jiangzhenyu1201@hotmail.com, E-mail: jianxu@engr.psu.edu; Liu, Yan; Mo, Chen

In an attempt to suppress the dark current, the barrier layer engineer for solution-processed PbSe colloidal quantum-dot (CQD) photodetectors has been investigated in the present study. It was found that the dark current can be significantly suppressed by implementing two types of carrier blocking layers, namely, hole blocking layer and electron blocking layer, sandwiched in between two active PbSe CQD layers. Meanwhile no adverse impact has been observed for the photo current. Our study suggests that this improvement resides on the transport pathway created via carrier recombination at intermediate layer, which provides wide implications for the suppression of dark currentmore » for infrared photodetectors.« less

Novel Drift Structures for Silicon and Compound Semiconductor X-Ray and Gamma-Ray Detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley E. Patt; Jan S. Iwanczyk

Recently developed silicon- and compound-semiconductor-based drift detector structures have produced excellent performance for charged particles, X rays, and gamma rays and for low-signal visible light detection. The silicon drift detector (SDD) structures that we discuss relate to direct X-ray detectors and scintillation photon detectors coupled with scintillators for gamma rays. Recent designs include several novel features that ensure very low dark current (both bulk silicon dark current and surface dark current) and hence low noise. In addition, application of thin window technology ensures a very high quantum efficiency entrance window on the drift photodetector.

Effects of Displacement Damage on the Time-Resolved Gain and Bandwidth of a Low Breakdown Voltage Si Avalanche Photodiode

NASA Technical Reports Server (NTRS)

Laird, Jamie S.; Onoda, Shinobu; Hirao, Toshio; Becker, Heidi; Johnston, Allan; Laird, Jamie S.; Itoh, Hisayoshi

2006-01-01

Effects of displacement damage and ionization damage induced by gamma irradiation on the dark current and impulse response of a high-bandwidth low breakdown voltage Si Avalanche Photodiode has been investigated using picosecond laser microscopy. At doses as high as 10Mrad (Si) minimal alteration in the impulse response and bandwidth were observed. However, dark current measurements also performed with and without biased irradiation exhibit anomalously large damage factors for applied biases close to breakdown. The absence of any degradation in the impulse response is discussed as are possible mechanisms for higher dark current damage factors observed for biased irradiation.

Direct Search for Dark Matter with DarkSide

NASA Astrophysics Data System (ADS)

Agnes, P.; Alexander, T.; Alton, A.; Arisaka, K.; Back, H. O.; Baldin, B.; Biery, K.; Bonfini, G.; Bossa, M.; Brigatti, A.; Brodsky, J.; Budano, F.; Cadonati, L.; Calaprice, F.; Canci, N.; Candela, A.; Cao, H.; Cariello, M.; Cavalcante, P.; Chavarria, A.; Chepurnov, A.; Cocco, A. G.; Crippa, L.; D'Angelo, D.; D'Incecco, M.; Davini, S.; De Deo, M.; Derbin, A.; Devoto, A.; Di Eusanio, F.; Di Pietro, G.; Edkins, E.; Empl, A.; Fan, A.; Fiorillo, G.; Fomenko, K.; Forster, G.; Franco, D.; Gabriele, F.; Galbiati, C.; Goretti, A.; Grandi, L.; Gromov, M.; Guan, M. Y.; Guardincerri, Y.; Hackett, B.; Herner, K.; Hungerford, E. V.; Ianni, Al; Ianni, An; Jollet, C.; Keeter, K.; Kendziora, C.; Kidner, S.; Kobychev, V.; Koh, G.; Korablev, D.; Korga, G.; Kurlej, A.; Li, P. X.; Loer, B.; Lombardi, P.; Love, C.; Ludhova, L.; Luitz, S.; Ma, Y. Q.; Machulin, I.; Mandarano, A.; Mari, S.; Maricic, J.; Marini, L.; Martoff, C. J.; Meregaglia, A.; Meroni, E.; Meyers, P. D.; Milincic, R.; Montanari, D.; Montuschi, M.; Monzani, M. E.; Mosteiro, P.; Mount, B.; Muratova, V.; Musico, P.; Nelson, A.; Odrowski, S.; Okounkova, M.; Orsini, M.; Ortica, F.; Pagani, L.; Pallavicini, M.; Pantic, E.; Papp, L.; Parmeggiano, S.; Parsells, R.; Pelczar, K.; Pelliccia, N.; Perasso, S.; Pocar, A.; Pordes, S.; Pugachev, D.; Qian, H.; Randle, K.; Ranucci, G.; Razeto, A.; Reinhold, B.; Renshaw, A.; Romani, A.; Rossi, B.; Rossi, N.; Rountree, S. D.; Sablone, D.; Saggese, P.; Saldanha, R.; Sands, W.; Sangiorgio, S.; Segreto, E.; Semenov, D.; Shields, E.; Skorokhvatov, M.; Smirnov, O.; Sotnikov, A.; Stanford, C.; Suvorov, Y.; Tartaglia, R.; Tatarowicz, J.; Testera, G.; Tonazzo, A.; Unzhakov, E.; Vogelaar, R. B.; Wada, M.; Walker, S.; Wang, H.; Wang, Y.; Watson, A.; Westerdale, S.; Wojcik, M.; Wright, A.; Xiang, X.; Xu, J.; Yang, C. G.; Yoo, J.; Zavatarelli, S.; Zec, A.; Zhu, C.; Zuzel, G.

2015-11-01

The DarkSide experiment is designed for the direct detection of Dark Matter with a double phase liquid Argon TPC operating underground at Laboratori Nazionali del Gran Sasso. The TPC is placed inside a 30 tons liquid organic scintillator sphere, acting as a neutron veto, which is in turn installed inside a 1 kt water Cherenkov detector. The current detector is running since November 2013 with a 50 kg atmospheric Argon fill and we report here the first null results of a Dark Matter search for a (1422 ± 67) kg.d exposure. This result correspond to a 90% CL upper limit on the WIMP-nucleon cross section of 6.1 × 10-44 cm2 (for a WIMP mass of 100 GeV/c2) and it's currently the most sensitive limit obtained with an Argon target.

The DarkSide direct dark matter search with liquid argon

NASA Astrophysics Data System (ADS)

Edkins, E.; Agnes, P.; Alexander, T.; Alton, A.; Arisaka, K.; Back, H. O.; Baldin, B.; Biery, K.; Bonfini, G.; Bossa, M.; Brigatti, A.; Brodsky, J.; Budano, F.; Cadonati, L.; Calaprice, F.; Canci, N.; Candela, A.; Cao, H.; Cariello, M.; Cavalcante, P.; Chavarria, A.; Chepurnov, A.; Cocco, A. G.; Crippa, L.; D'Angelo, D.; D'Incecco, M.; Davini, S.; De Deo, M.; Derbin, A.; Devoto, A.; Di Eusanio, F.; Di Pietro, G.; Empl, A.; Fan, A.; Fiorillo, G.; Fomenko, K.; Forster, G.; Franco, D.; Gabriele, F.; Galbiati, C.; Goretti, A.; Grandi, L.; Gromov, M.; Guan, M. Y.; Guardincerri, Y.; Hackett, B.; Herner, K.; Humble, P.; Hungerford, E. V.; Ianni, Al.; Ianni, An.; Jollet, C.; Keeter, K.; Kendziora, C.; Kobychev, V.; Koh, G.; Korablev, D.; Korga, G.; Kurlej, A.; Li, P. X.; Loer, B.; Lombardi, P.; Love, C.; Ludhova, L.; Luitz, S.; Ma, Y. Q.; Machulin, I.; Mandarano, A.; Mari, S.; Maricic, J.; Marini, L.; Martoff, C. J.; Meregaglia, A.; Meroni, E.; Meyers, P. D.; Milincic, R.; Montanari, D.; Montuschi, M.; Monzani, M. E.; Mosteiro, P.; Mount, B.; Muratova, V.; Musico, P.; Nelson, A.; Odrowski, S.; Okounkova, M.; Orsini, M.; Ortica, F.; Pagani, L.; Pallavicini, M.; Pantic, E.; Papp, L.; Parmeggiano, S.; Parsells, R.; Pelczar, K.; Pelliccia, N.; Perasso, S.; Pocar, A.; Pordes, S.; Pugachev, D.; Qian, H.; Randle, K.; Ranucci, G.; Razeto, A.; Reinhold, B.; Renshaw, A.; Romani, A.; Rossi, B.; Rossi, N.; Rountree, S. D.; Sablone, D.; Saggese, P.; Saldanha, R.; Sands, W.; Sangiorgio, S.; Segreto, E.; Semenov, D.; Shields, E.; Skorokhvatov, M.; Smirnov, O.; Sotnikov, A.; Stanford, C.; Suvorov, Y.; Tartaglia, R.; Tatarowicz, J.; Testera, G.; Tonazzo, A.; Unzhakov, E.; Vogelaar, R. B.; Wada, M.; Walker, S.; Wang, H.; Wang, Y.; Watson, A.; Westerdale, S.; Wojcik, M.; Wright, A.; Xiang, X.; Xu, J.; Yang, C. G.; Yoo, J.; Zavatarelli, S.; Zec, A.; Zhu, C.; Zuzel, G.

2017-11-01

The DarkSide-50 direct dark matter detector is a liquid argon time projection chamber (TPC) surrounded by a liquid scintillator neutron veto (LSV) and a water Cerenkov muon veto (WCV). Located under 3800 m.w.e. at the Laboratori Nazionali del Gran Sasso, Italy, it is the only direct dark matter experiment currently operating background free. The atmospheric argon target was replaced with argon from underground sources in April, 2015. The level of 39Ar, a β emitter present in atmospheric argon (AAr), has been shown to have been reduced by a factor of (1.4 ± 0.2) x 103. The combined spin-independent WIMP exclusion limit of 2.0 x 10-44 cm2 (mχ = 100 GeV/c2) is currently the best limit on a liquid argon target.

VALIDATING the Accuracy of Sighten's Automated Shading Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solar companies - including installers, financiers, and distributors - leverage Sighten software to deliver accurate shading calculations and solar proposals. Sighten recently partnered with Google Project Sunroof to provide automated remote shading analysis directly within the Sighten platform. The National Renewable Energy Laboratory (NREL), in partnership with Sighten, independently verified the accuracy of Sighten's remote-shading solar access values (SAVs) on an annual basis for locations in Los Angeles, California, and Denver, Colorado.

An Appraisal of the Classic Forest Succession Paradigm with the Shade Tolerance Index

PubMed Central

Lienard, Jean; Florescu, Ionut; Strigul, Nikolay

2015-01-01

In this paper we revisit the classic theory of forest succession that relates shade tolerance and species replacement and assess its validity to understand patch-mosaic patterns of forested ecosystems of the USA. We introduce a macroscopic parameter called the “shade tolerance index” and compare it to the classic continuum index in southern Wisconsin forests. We exemplify shade tolerance driven succession in White Pine-Eastern Hemlock forests using computer simulations and analyzing approximated chronosequence data from the USDA FIA forest inventory. We describe this parameter across the last 50 years in the ecoregions of mainland USA, and demonstrate that it does not correlate with the usual macroscopic characteristics of stand age, biomass, basal area, and biodiversity measures. We characterize the dynamics of shade tolerance index using transition matrices and delimit geographical areas based on the relevance of shade tolerance to explain forest succession. We conclude that shade tolerance driven succession is linked to climatic variables and can be considered as a primary driving factor of forest dynamics mostly in central-north and northeastern areas in the USA. Overall, the shade tolerance index constitutes a new quantitative approach that can be used to understand and predict succession of forested ecosystems and biogeographic patterns. PMID:25658092

Adolescents’ use of purpose built shade in secondary schools: cluster randomised controlled trial

PubMed Central

White, Vanessa; Wakefield, Melanie A; Jamsen, Kris M; White, Victoria; Livingston, Patricia M; English, Dallas R; Simpson, Julie A

2009-01-01

Objective To examine whether students use or avoid newly shaded areas created by shade sails installed at schools. Design Cluster randomised controlled trial with secondary schools as the unit of randomisation. Setting 51 secondary schools with limited available shade, in Australia, assessed over two spring and summer terms. Participants Students outside at lunch times. Intervention Purpose built shade sails were installed in winter 2005 at full sun study sites to increase available shade for students in the school grounds. Main outcome measure Mean number of students using the primary study sites during weekly observations at lunch time. Results Over the study period the mean change in students using the primary study site from pre-test to post-test was 2.63 (95% confidence interval 0.87 to 4.39) students in intervention schools and −0.03 (−1.16 to 1.09) students in control schools. The difference in mean change between groups was 2.67 (0.65 to 4.68) students (P=0.011). Conclusions Students used rather than avoided newly shaded areas provided by purpose built shade sails at secondary schools in this trial, suggesting a practical means of reducing adolescents’ exposure to ultraviolet radiation. Trial registration Exempt. PMID:19223344

Interior shadings for office indoor visual comfort in humid climate region

NASA Astrophysics Data System (ADS)

Dinapradipta, Asri; Sudarma, Erwin; Defiana, Ima; Erwindi, Collinthia

2018-03-01

As part of the fenestration system, the interior shadings have also a role to control the indoor environment to maintain indoor visual comfort. As the occupants have personal access to control these, their control behavior then, might enhance or even worsen indoor comfort performance. The controlling behavior might not only influence indoor comfort performance but can also indicate the success or failure of interior shading as a control device element. This paper is intended to report control behavior patterns, as represented by the variety of the slats’ openings of two types of interior shading i.e. Venetian and Vertical blinds and to analyze these on the concurrent impacts to indoor office building’s indoor illuminance and luminance distribution. The purpose of this research is to figure out the shading control patterns as well as to examine the effectiveness of these two types of interior shadings to control indoor visual environment. This study is a quantitative research using experimentation on the slats’ opening of two types of shadings at two identical office rooms. The research results suggested that both types of blinds seem unsuitable for gaining proper illumination values at work planes in humid tropics area. However, these shadings demonstrate good performance for luminance distribution except for that of the closed Venetian blinds.

Photojunction field-effect transistor based on a colloidal quantum dot absorber channel layer.

PubMed

Adinolfi, Valerio; Kramer, Illan J; Labelle, André J; Sutherland, Brandon R; Hoogland, S; Sargent, Edward H

2015-01-27

The performance of photodetectors is judged via high responsivity, fast speed of response, and low background current. Many previously reported photodetectors based on size-tuned colloidal quantum dots (CQDs) have relied either on photodiodes, which, since they are primary photocarrier devices, lack gain; or photoconductors, which provide gain but at the expense of slow response (due to delayed charge carrier escape from sensitizing centers) and an inherent dark current vs responsivity trade-off. Here we report a photojunction field-effect transistor (photoJFET), which provides gain while breaking prior photoconductors' response/speed/dark current trade-off. This is achieved by ensuring that, in the dark, the channel is fully depleted due to a rectifying junction between a deep-work-function transparent conductive top contact (MoO3) and a moderately n-type CQD film (iodine treated PbS CQDs). We characterize the rectifying behavior of the junction and the linearity of the channel characteristics under illumination, and we observe a 10 μs rise time, a record for a gain-providing, low-dark-current CQD photodetector. We prove, using an analytical model validated using experimental measurements, that for a given response time the device provides a two-orders-of-magnitude improvement in photocurrent-to-dark-current ratio compared to photoconductors. The photoJFET, which relies on a junction gate-effect, enriches the growing family of CQD photosensitive transistors.

Quantum Dot Detector Enhancement for Narrow Band Multispectral Applications

DTIC Science & Technology

2012-10-01

19 2.4.3 Dark Current and Noise Current Measurement of QDIPs.................................21 3 References...20 Figure 19: Dark Current of QDIPs Measured by Source Meter…………………………………………21 Figure 20: Schematic View of Noise Current Setup...temperature, higher photoconductive gain, carrier lifetimes 10-100 times longer than Quantum Well Infrared Photodetectors ( QWIPs ), and giving rise to a

Shading Vita In-ceram YZ substructures: influence on value and chroma, part II.

PubMed

Devigus, A; Lombardi, G

2004-10-01

In this study, the influence of differently shaded substructures made of Y-TZP from different manufacturers (without, with 0.5 mm or 1.0 mm ceramic veneer with Vita VM9 Base Dentin) on the lightness, the saturation, and the color shade (= value, chroma, and hue) was measured and assessed with a spectral photometer (Easy Shade, Vita) on a clinical case in the mouth and on models of different color. Shading substructures made of Y-TZP facilitated adaptation to the basic shade and reduced the layer thickness of the veneer ceramic required to achieve the desired color. This should be done in the future as a matter of routine. In this way, tooth substance can be better conserved when preparing the teeth, and the esthetic result is not diminished. The material used for the production of the working models (plaster or plastic) should be tooth colored and in terms of lightness--analogous to the shading of the substructure--in order to facilitate clinical color measurement and quality control in the laboratory.

The effects of shade on performance, carcass classes and behaviour of heat-stressed feedlot cattle at the finisher phase.

PubMed

Blaine, K L; Nsahlai, Ignatius Verla

2011-03-01

The study aimed to determine the impact of shade on the performance, carcass class and behaviour using 146 crossbred steers and bulls during the finishing phase on a commercial feedlot in February. Treatments were (1) shade and (2) no shade. Average daily gain (ADG), DMI, and feed efficiency were measured, and hot carcass weight (HCW) and grades were collected at slaughter. The proportion of animals within a pen engaged in various behavioural activities (standing, lying, feeding and panting) was recorded. Five randomly selected individual animals per treatment were monitored every 2 min between 0700 and 1600 hours to determine the time spent on each of the above activities. Shade improved the final body weight (P < 0.0001), ADG (P = 0.079), and HCW by 8.33 kg (P < 0.05). Shade increased (P < 0.05) the feeding activity but decreased (P < 0.05) panting behaviour. Shade conferred an economic benefit of R2.03 head(-1)week(-1), and thus would reduce heat stress and increase the feedlot profitability.

Improved color matching of metal ceramic restorations. Part II: Procedures for visual communication.

PubMed

Sorensen, J A; Torres, T J

1987-12-01

Most ceramic restorations are fabricated in a location remote from the dental office. Successful fabrication of matching life-like ceramic restorations necessitates a collaborative effort between the dentist and the ceramist. To meet the demands for visual communication of shade and surface texture, the following steps are recommended. 1. A means of communicating and recording surface texture that facilitates blending the restorations with the natural dentition should be used. 2. The system should use an esthetics prescription form that functions with the Shade Indicator Chart system to relate the shade of opaque, body, and incisal porcelains and their arrangement to the ceramist. 3. An easily made identification mold to form shade tabs is needed. 4. Identification shade tabs should be made to verify and document shade formulations selected with the Shade Indicator Chart system. 5. Methods for precisely mapping and reproducing individual characterization patterns are needed. This information permits the visualization of the end result, allowing the artistic expression of the ceramist to create vital-appearing restorations intrinsically and in harmony with the natural dentition.

Dark respiration rate increases with plant size in saplings of three temperate tree species despite decreasing tissue nitrogen and nonstructural carbohydrates.

PubMed

Machado, José-Luis; Reich, Peter B

2006-07-01

In shaded environments, minimizing dark respiration during growth could be an important aspect of maintaining a positive whole-plant net carbon balance. Changes with plant size in both biomass distribution to different tissue types and mass-specific respiration rates (R(d)) of those tissues would have an impact on whole-plant respiration. In this paper, we evaluated size-related variation in R(d), biomass distribution, and nitrogen (N) and total nonstructural carbohydrate (TNC) concentrations of leaves, stems and roots of three cold-temperate tree species (Abies balsamea (L.) Mill, Acer rubrum L. and Pinus strobus L.) in a forest understory. We sampled individuals varying in age (6 to 24 years old) and in size (from 2 to 500 g dry mass), and growing across a range of irradiances (from 1 to 13% of full sun) in northern Minnesota, USA. Within each species, we found small changes in R(d), N and TNC when comparing plants growing across this range of light availability. Consistent with our hypotheses, as plants grew larger, whole-plant N and TNC concentrations in all species declined as a result of a combination of changes in tissue N and shifts in biomass distribution patterns. However, contrary to our hypotheses, whole-plant and tissue R(d) increased with plant size in the three species.

Broadband and Resonant Approaches to Axion Dark Matter Detection.

PubMed

Kahn, Yonatan; Safdi, Benjamin R; Thaler, Jesse

2016-09-30

When ultralight axion dark matter encounters a static magnetic field, it sources an effective electric current that follows the magnetic field lines and oscillates at the axion Compton frequency. We propose a new experiment to detect this axion effective current. In the presence of axion dark matter, a large toroidal magnet will act like an oscillating current ring, whose induced magnetic flux can be measured by an external pickup loop inductively coupled to a SQUID magnetometer. We consider both resonant and broadband readout circuits and show that a broadband approach has advantages at small axion masses. We estimate the reach of this design, taking into account the irreducible sources of noise, and demonstrate potential sensitivity to axionlike dark matter with masses in the range of 10^{-14}-10^{-6}  eV. In particular, both the broadband and resonant strategies can probe the QCD axion with a GUT-scale decay constant.

Low dark current MCT-based focal plane detector arrays for the LWIR and VLWIR developed at AIM

NASA Astrophysics Data System (ADS)

Gassmann, Kai Uwe; Eich, Detlef; Fick, Wolfgang; Figgemeier, Heinrich; Hanna, Stefan; Thöt, Richard

2015-10-01

For nearly 40 years AIM develops, manufactures and delivers photo-voltaic and photo-conductive infrared sensors and associated cryogenic coolers which are mainly used for military applications like pilotage, weapon sights, UAVs or vehicle platforms. In 2005 AIM started to provide the competences also for space applications like IR detector units for the SLSTR instrument on board of the Sentinel 3 satellite, the hyperspectral SWIR Imager for EnMAP or pushbroom detectors for high resolution Earth observation satellites. Meanwhile AIM delivered more than 25 Flight Models for several customers. The first European pulse-tube cooler ever operating on-board of a satellite is made by AIM. AIM homes the required infrared core capabilities such as design and manufacturing of focal plane assemblies, detector housing technologies, development and manufacturing of cryocoolers and also data processing for thermal IR cameras under one roof which enables high flexibility to react to customer needs and assures economical solutions. Cryogenically cooled Hg(1-x)CdxTe (MCT) quantum detectors are unequalled for applications requiring high imaging as well as high radiometric performance in the infrared spectral range. Compared with other technologies, they provide several advantages, such as the highest quantum efficiency, lower power dissipation compared to photoconductive devices and fast response times, hence outperforming micro-bolometer arrays. However, achieving an excellent MCT detector performance at long (LWIR) and very long (VLWIR) infrared wavelengths is challenging due to the exponential increase in the thermally generated photodiode dark current with increasing cut-off wavelength and / or operating temperature. Dark current is a critical design driver, especially for LWIR / VLWIR multi-spectral imagers with moderate signal levels or hyper-spectral Fourier spectrometers operating deep into the VLWIR spectral region. Consequently, low dark current (LDC) technologies are the prerequisite for future scientific space and earth observation missions. Aiming, for example at exoplanet or earth atmospheric spectral analysis, significant improvement in LWIR / VLWIR detector material performance is mandatory. LDC material optimization can target different directions of impact: (i) reduction of dark current for a given operational temperature to increase SNR and reduce thermally induced signal offset variations. (ii) operation at elevated temperatures at a given dark current level to reduce mass and power budget of the required cryocooler and to reduce cryostat complexity. (iii) increase the accessible cut-off wavelength at constant detector temperature and dark current level. This paper presents AIM's latest results on n-on-p as well as p-on-n low dark current planar MCT photodiode focal plane detector arrays at cut-off wavelengths >11 μm at 80 K. Dark current densities below Tennant's `Rule07'1 have been demonstrated for n-on-p and p-on-n devices. This work has been carried out under ESA contract ESTEC 4000107414/13/NL/SFe².

One dark matter mystery: halos in the cosmic web

NASA Astrophysics Data System (ADS)

Gaite, Jose

2015-01-01

The current cold dark matter cosmological model explains the large scale cosmic web structure but is challenged by the observation of a relatively smooth distribution of matter in galactic clusters. We consider various aspects of modeling the dark matter around galaxies as distributed in smooth halos and, especially, the smoothness of the dark matter halos seen in N-body cosmological simulations. We conclude that the problems of the cold dark matter cosmology on small scales are more serious than normally admitted.

Quantum field theory of interacting dark matter and dark energy: Dark monodromies

DOE PAGES

D’Amico, Guido; Hamill, Teresa; Kaloper, Nemanja

2016-11-28

We discuss how to formulate a quantum field theory of dark energy interacting with dark matter. We show that the proposals based on the assumption that dark matter is made up of heavy particles with masses which are very sensitive to the value of dark energy are strongly constrained. Quintessence-generated long-range forces and radiative stability of the quintessence potential require that such dark matter and dark energy are completely decoupled. However, if dark energy and a fraction of dark matter are very light axions, they can have significant mixings which are radiatively stable and perfectly consistent with quantum field theory.more » Such models can naturally occur in multi-axion realizations of monodromies. The mixings yield interesting signatures which are observable and are within current cosmological limits but could be constrained further by future observations« less

Quantum field theory of interacting dark matter and dark energy: Dark monodromies

DOE Office of Scientific and Technical Information (OSTI.GOV)

D’Amico, Guido; Hamill, Teresa; Kaloper, Nemanja

We discuss how to formulate a quantum field theory of dark energy interacting with dark matter. We show that the proposals based on the assumption that dark matter is made up of heavy particles with masses which are very sensitive to the value of dark energy are strongly constrained. Quintessence-generated long-range forces and radiative stability of the quintessence potential require that such dark matter and dark energy are completely decoupled. However, if dark energy and a fraction of dark matter are very light axions, they can have significant mixings which are radiatively stable and perfectly consistent with quantum field theory.more » Such models can naturally occur in multi-axion realizations of monodromies. The mixings yield interesting signatures which are observable and are within current cosmological limits but could be constrained further by future observations« less

Design of a radiator shade for testing in a simulated lunar environment

NASA Technical Reports Server (NTRS)

Huff, Jaimi; Remington, Randy; Tang, Toan

1992-01-01

The National Aeronautics and Space Administration (NASA) and The Universities Space Research Association (USRA) have chosen the parabolic/catenary concept from their sponsored Fall 1991 lunar radiation shade project for further testing and development. NASA asked the design team to build a shading device and support structure for testing in a vacuum chamber. Besides the support structure for the catenary shading device, the design team was asked to develop a system for varying the shade shape so that the device can be tested at different focal lengths. The design team developed concept variants and combined the concept variants to form overall designs. Using a decision matrix, an overall design was selected by the team from several overall design alternatives. Concept variants were developed for three primary functions. The three functions were structural support, shape adjustments, and end shielding. The shade adjustment function was divided into two sub-functions, arc length adjustment, and width adjustment.

Maintenance of eastern hemlock forests: Factors associated with hemlock vulnerability to hemlock woolly adelgid

Treesearch

Mary Ann Fajvan; Petra Bohall Wood

2010-01-01

Eastern hemlock (Tsuga canadensis [L.]) is the most shade-tolerant and long-lived tree species in eastern North America. The hemlock woolly adelgid (Adelges tsugae) (HWA), is a nonnative invasive insect that feeds on eastern hemlock and Carolina hemlock (Tsuga caroliniana Engelm.). HWA currently is established in...

What Does Creativity Mean in English Education?

ERIC Educational Resources Information Center

Compton, Ashley

2007-01-01

Creativity is seen as important to society by the current Prime Minister and the Department for Education and Skills and is present in curriculum documents applying from birth to 16 years old but with various shades of meaning. Unfortunately, the term creativity is used in English education and the larger society without a clear definition. The…

Computer Ethics: A Slow Fade from Black and White to Shades of Gray

ERIC Educational Resources Information Center

Kraft, Theresa A.; Carlisle, Judith

2011-01-01

The expanded use of teaching case based analysis based on current events and news stories relating to computer ethics improves student engagement, encourages creativity and fosters an active learning environment. Professional ethics standards, accreditation standards for computer curriculum, ethics theories, resources for ethics on the internet,…

Regenerating uneven-aged stands of loblolly and shortleaf pines: the current state of knowledge

Treesearch

Michael G. Shelton; Michael D. Cain

2000-01-01

Periodic regeneration is crucial to creating or sustaining uneven-aged (UEA) stands of loblolly (Pinus taeda L.) and shortleaf (P. echinata Mill.) pines. Although both species are shade intolerant, they have silvical characteristics that are conducive to natural regeneration in UEA stands. Their seed production is fairly consistent...

Asian Shades of Spirituality: Implications for Multicultural School Counseling

ERIC Educational Resources Information Center

Hanna, Fred J.; Green, Alan

2004-01-01

In the current practice of school counseling, little consideration is given to the spiritual background of students of Asian cultures. Although there is a body of literature on Asian culture in counseling, the authors could find remarkably few articles pertaining to counseling students in the context of Asian religious and spiritual traditions. In…

High-Intensity Fires May Be Unnecessary For Stand Replacement Of Table Mountain Pine: An Overview Of Current Research

Treesearch

Thomas A. Waldrop; Patrick H. Brose; Nicole Turrill Welch; Helen H. Mohr; Ellen A. Gray; Frank H. Tainter; Lisa E. Ellis

2002-01-01

Abstract - After several decades of fire suppression, ridgetop pine communities of the Southern Appalachians are entering later seral stages and beginning to disappear. They typically have an overstory of Table Mountain pine (Pinus pungens), which is being replaced by shade-tolerant chestnut oaks (Quercus prinus...

Gravitational Waves from Binary Mergers of Subsolar Mass Dark Black Holes

NASA Astrophysics Data System (ADS)

Shandera, Sarah; Jeong, Donghui; Gebhardt, Henry S. Grasshorn

2018-06-01

We explore the possible spectrum of binary mergers of subsolar mass black holes formed out of dark matter particles interacting via a dark electromagnetism. We estimate the properties of these dark black holes by assuming that their formation process is parallel to Population-III star formation, except that dark molecular cooling can yield a smaller opacity limit. We estimate the binary coalescence rates for the Advanced LIGO and Einstein telescope, and find that scenarios compatible with all current constraints could produce dark black holes at rates high enough for detection by Advanced LIGO.

In vitro and in vivo evaluations of three computer-aided shade matching instruments.

PubMed

Yuan, Kun; Sun, Xiang; Wang, Fu; Wang, Hui; Chen, Ji-hua

2012-01-01

This study evaluated the accuracy and reliability of three computer-aided shade matching instruments (Shadepilot, VITA Easyshade, and ShadeEye NCC) using both in vitro and in vivo models. The in vitro model included the measurement of five VITA Classical shade guides. The in vivo model utilized three instruments to measure the central region of the labial surface of maxillary right central incisors of 85 people. The accuracy and reliability of the three instruments in these two evaluating models were calculated. Significant differences were observed in the accuracy of instruments both in vitro and in vivo. No significant differences were found in the reliability of instruments between and within the in vitro and the in vivo groups. VITA Easyshade was significantly different in accuracy between in vitro and in vivo models, while no significant difference was found for the other two instruments. Shadepilot was the only instrument tested in the present study that showed high accuracy and reliability both in vitro and in vivo. Significant differences were observed in the L*a*b* values of the 85 natural teeth measured using three instruments in the in vivo assessment. The pair-agreement rates of shade matching among the three instruments ranged from 37.7% to 48.2%, and the incidence of identical shade results shared by all three instruments was 25.9%. As different L*a*b* values and shade matching results were reported for the same tooth, a combination of the evaluated shade matching instruments and visual shade confirmation is recommended for clinical use.

A field measure of the shade fraction

NASA Technical Reports Server (NTRS)

Gillespie, Alan R.; Smith, Milton O.; Sabol, Donald E.

1992-01-01

'Shade' has a technical definition peculiar to linear spectral mixture analysis of imaging spectrometer data: it is the reduction in radiance from a surface due to lighting conditions and geometry, and includes topographic shading described by photometric functions as well as shadowing at all scales. 'Shade' is an important constituent of nearly all remotely sensed images, and is one endmember resolved in spectral mixture analysis, where it is represented as a fraction of the measured radiance and a characteristic spectrum. This spectrum is typically the null vector, provided the data have been corrected for atmospheric and instrument effects: i.e., 'shade' is the radiance from an ideal black surface. In topographic shading, irradiance is reduced - typically in proportion to cos(i), where i (incidence angle) is the angle between the sun and the local surface normal vectors. Therefore, the radiance is lowered by a multiplicative factor. Shadowing occurs when i is greater than 90 deg, or when sunlight is blocked by adjacent high terrain; the only irradiance is down-welling skylight and bounce light from adjacent terrain. In spectral mixture analysis, 'shade' is regarded as an additive term. In this regard, it is an accurate description of the proportion of a scene that consists of ideal shadows ('checkerboard mixing'); however, 'shade' represents the multiplicative cos(i) factor as well, as here it should be interpreted as the proportion of shadow that would darken the scene an equivalent amount. In either case, the 'shade' fraction is lessened by adjacency effects, because the scene has a non-zero reflectivity instead of the ideal black surface generally assumed.

Differential responses of double petal and multi petal jasmine to shading: I. Photosynthetic characteristics and chloroplast ultrastructure.

PubMed

Deng, Yanming; Li, Congcong; Shao, Qingsong; Ye, Xiaoqing; She, Jianming

2012-06-01

A double petal (DP) and a multi petal (MP) type jasmine (Jasminum sambac Ait.) growth and flowering was known largely affected by different levels of irradiance. Here, our objective was to determine the effects of shade on photosynthesis related characteristics and chloroplast ultrastructure of these two types. In both types, net photosynthetic rate (Pn), stomatal conductance (g(s)) and transpiration rate increased with decreasing irradiance from 100% to 20%, while both maximum and variable fluorescence showed a steady increase, and photochemical and nonphotochemical quenching indexes declined. At each conducted time, chlorophyll a, b and carotenoids contents in DP type shaded leaves increased whereas those in MP type decreased at 5% irradiance (considered as extreme shade). The maximum photochemical efficiency of photosystem II of DP plants showed subtle changes but that of MP plants declined by shading thereafter 21 days of treatment. Observation of chloroplast ultrastructure showed its best development in the leaves of DP and MP types mostly from 50% to 20% irradiance (considered as weak and moderate shade, respectively). At each shade treatment, Pn, g(s) and water use efficiency of DP-jasmine were always higher than those of MP-jasmine, thus the shade tolerance ability of the former was higher than that of the latter. The results showed that full sunlight and 5% natural irradiance caused photoinhibition and light deficiency of jasmine plants respectively, and modulating chloroplast development by the more numbers of thylakoids and grana to contain more photosynthetic pigments is an important shade tolerance mechanism of DP type. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

Dark sequential Z ' portal: Collider and direct detection experiments

NASA Astrophysics Data System (ADS)

Arcadi, Giorgio; Campos, Miguel D.; Lindner, Manfred; Masiero, Antonio; Queiroz, Farinaldo S.

2018-02-01

We revisit the status of a Majorana fermion as a dark matter candidate when a sequential Z' gauge boson dictates the dark matter phenomenology. Direct dark matter detection signatures rise from dark matter-nucleus scatterings at bubble chamber and liquid xenon detectors, and from the flux of neutrinos from the Sun measured by the IceCube experiment, which is governed by the spin-dependent dark matter-nucleus scattering. On the collider side, LHC searches for dilepton and monojet + missing energy signals play an important role. The relic density and perturbativity requirements are also addressed. By exploiting the dark matter complementarity we outline the region of parameter space where one can successfully have a Majorana dark matter particle in light of current and planned experimental sensitivities.

Status and perspective of the DarkSide experiment at LNGS

DOE PAGES

Agnes, P.

2018-09-01

The DarkSide experiment aims to perform a background-free direct search for dark matter with a dual-phase argon TPC. The current phase of the experiment, DarkSide-50, is acquiring data at Laboratori Nazionali del Gran Sasso and produced the most sensitive limit on the WIMP-nucleon cross section ever obtained with a liquid argon target (2.0 × 10 -44 cm2 for a WIMP mass of 100 GeV/c 2). The future phase of the experiment will be a 20 t fiducial mass detector, designed to reach a sensitivity of ~1 × 10 -47 cm2 (at 1 TeV/c 2 WIMP mass) with a background-free exposuremore » of 100 ty. Here, this work contains a discussion of the current status of the DarkSide-50 WIMP search and of the results which are more relevant for the construction of the future detector.« less

Direct search for dark matter with DarkSide

DOE PAGES

Agnes, P.

2015-11-16

Here, the DarkSide experiment is designed for the direct detection of Dark Matter with a double phase liquid Argon TPC operating underground at Laboratori Nazionali del Gran Sasso. The TPC is placed inside a 30 tons liquid organic scintillator sphere, acting as a neutron veto, which is in turn installed inside a 1 kt water Cherenkov detector. The current detector is running since November 2013 with a 50 kg atmospheric Argon fill and we report here the first null results of a Dark Matter search for a (1422 ± 67) kg.d exposure. This result correspond to a 90% CL uppermore » limit on the WIMP-nucleon cross section of 6.1 × 10 -44 cm 2 (for a WIMP mass of 100 GeV/c 2) and it's currently the most sensitive limit obtained with an Argon target.« less

Status and perspective of the DarkSide experiment at LNGS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agnes, P.

The DarkSide experiment aims to perform a background-free direct search for dark matter with a dual-phase argon TPC. The current phase of the experiment, DarkSide-50, is acquiring data at Laboratori Nazionali del Gran Sasso and produced the most sensitive limit on the WIMP-nucleon cross section ever obtained with a liquid argon target (2.0 × 10 -44 cm2 for a WIMP mass of 100 GeV/c 2). The future phase of the experiment will be a 20 t fiducial mass detector, designed to reach a sensitivity of ~1 × 10 -47 cm2 (at 1 TeV/c 2 WIMP mass) with a background-free exposuremore » of 100 ty. Here, this work contains a discussion of the current status of the DarkSide-50 WIMP search and of the results which are more relevant for the construction of the future detector.« less

Clinical evaluation of a new 10% carbamide peroxide tooth-whitening agent.

PubMed

Barnes, D M; Kihn, P W; Romberg, E; George, D; DePaola, L; Medina, E

1998-10-01

NUPRO Gold Tooth Whitening System was evaluated for efficacy according to the proposed ADA guidelines for acceptance. Sixty participants with discolored anterior teeth participated in a 14-day, double-blind, clinical trial. The participants were matched for age, gender, and oral health status and were given either a placebo gel without the active agent or the NUPRO Gold active gel, which they wore in a custom-fabricated mouth guard for home use. The shade of each participant's maxillary anterior teeth was evaluated using a value-oriented Vita Lumin Vacuum Shade Guide before the study. The same shade guide was used to determine shade changes. Time of use of the agent and potential side effects, such as tooth and gingival hypersensitivity and tissue irritation, were assessed at all recall examinations and were recorded by participants in daily diaries. The average shade change for the placebo users was less than one shade. The average shade change for the NUPRO Gold users was 6.96 shades. Tooth hypersensitivity varied from none to severe. Tissue irritation was minimal. The results of these evaluations indicate that NUPRO Gold is effective as a tooth-whitening system, when administered properly under the supervision of a dentist, with commonly reported side effects of transient tooth sensitivity and minimal gingival sensitivity. Little or no change in tissue health was noted. This study was supported by Dentsply Preventive Care (York, Pennsylvania).

Leaf traits show different relationships with shade tolerance in moist versus dry tropical forests.

PubMed

Poorter, Lourens

2009-03-01

Shade tolerance is the central paradigm for understanding forest succession and dynamics, but there is considerable debate as to what the salient features of shade tolerance are, whether adult leaves show similar shade adaptations to seedling leaves, and whether the same leaf adaptations are found in forests under different climatic control. Here, adult leaf and metamer traits were measured for 39 tree species from a tropical moist semi-evergreen forest (1580 mm rain yr(-1)) and 41 species from a dry deciduous forest (1160 mm yr(-1)) in Bolivia. Twenty-six functional traits were measured and related to species regeneration light requirements.Adult leaf traits were clearly associated with shade tolerance. Different, rather than stronger, shade adaptations were found for moist compared with dry forest species. Shade adaptations exclusively found in the evergreen moist forest were related to tough and persistent leaves, and shade adaptations in the dry deciduous forest were related to high light interception and water use.These results suggest that, for forests differing in rainfall seasonality, there is a shift in the relative importance of functional leaf traits and performance trade-offs that control light partitioning. In the moist evergreen forest leaf traits underlying the growth-survival trade-off are important, whereas in the seasonally deciduous forest leaf traits underlying the growth trade-off between low and high light might become important.

Effects of shade on welfare and meat quality of grazing sheep under high ambient temperature.

PubMed

Liu, H W; Cao, Y; Zhou, D W

2012-12-01

This study was conducted to evaluate the effects of providing shade on growth performance, welfare, and meat quality of grazing sheep under high ambient temperature. A total of 120 healthy male Ujumqin wool sheep (a local breed; BW = 18.7 ± 1.27 kg; 14 wk old) were randomly and equally divided into shaded and unshaded treatments with 3 pens per treatment. Sheep were grazed on an unshaded pastureland from 0600 to 1000 h and 1400 to 1800 h. During other times, sheep were confined in shaded or unshaded pens. Body weight was recorded on d 1 and 42 of the experiment. Rectal temperature and respiration rate were recorded on d 7, 14, 21, 28, 35, and 42. At end of the trial, sheep were blood sampled and slaughtered to collect meat samples. Respiration rate was greater (P < 0.05) in the unshaded sheep than shaded sheep on d 14, 21, 28, 35, and 42 of the trial whereas no significant differences were found on d 7. Moreover, no differences were observed in final BW, ADG, or rectal temperature throughout the trial. The pH at 24 h postmortem (pH(24)) and cooking loss were greater (P < 0.01) in unshaded than shaded sheep. On the contrary, lightness (L*), redness (a*) and yellowness (b*) values at 24 h postmortem were lower (P < 0.05) in unshaded versus shaded sheep. The sheep in the unshaded group had a greater (P < 0.05) cortisol concentration compared with the shaded group. Sheep in the shaded group had lower creatine kinase activity (P < 0.01) as well as observed for glucose (P < 0.05), triiodothyronine (P < 0.01), and thyroxine (P < 0.05) concentrations and white blood cell count (P < 0.05). Compared with the unshaded group, sheep in the shaded group had a greater lymphocytes (LYM) count (P < 0.05). In contrast, the opposite was true for neutrophils (NEU) count (P < 0.01) and NEU:LYM ratio (P < 0.01). In conclusion, the shade cloth, although not enhancing ADG, improved meat quality traits and certain stress parameters in grazing sheep reared under high ambient temperature.

Seedling growth and biomass allocation in relation to leaf habit and shade tolerance among 10 temperate tree species.

PubMed

Modrzyński, Jerzy; Chmura, Daniel J; Tjoelker, Mark G

2015-08-01

Initial growth of germinated seeds is an important life history stage, critical for establishment and succession in forests. Important questions remain regarding the differences among species in early growth potential arising from shade tolerance. In addition, the role of leaf habit in shaping relationships underlying shade tolerance-related differences in seedling growth remains unresolved. In this study we examined variation in morphological and physiological traits among seedlings of 10 forest tree species of the European temperate zone varying in shade tolerance and leaf habit (broadleaved winter-deciduous species vs needle-leaved conifers) during a 10-week period. Seeds were germinated and grown in a controlled environment simulating an intermediate forest understory light environment to resolve species differences in initial growth and biomass allocation. In the high-resource experimental conditions during the study, seedlings increased biomass allocation to roots at the cost of leaf biomass independent of shade tolerance and leaf habit. Strong correlations between relative growth rate (RGR), net assimilation rate (NAR), leaf area ratio (LAR), specific leaf area (SLA) and leaf mass fraction (LMF) indicate that physiology and biomass allocation were equally important determinants of RGR as plant structure and leaf morphology among these species. Our findings highlight the importance of seed mass- and seed size-related root morphology (specific root length-SRL) for shade tolerance during early ontogeny. Leaf and plant morphology (SLA, LAR) were more successful in explaining variation among species due to leaf habit than shade tolerance. In both broadleaves and conifers, shade-tolerant species had lower SRL and greater allocation of biomass to stems (stem mass fraction). Light-seeded shade-intolerant species with greater SRL had greater RGR in both leaf habit groups. However, the greatest plant mass was accumulated in the group of heavy-seeded shade-tolerant broadleaves. The results of our study suggest that the combinations of plant attributes enhancing growth under high light vary with shade tolerance, but differ between leaf habit groups. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Enhanced low-noise gain from InAs avalanche photodiodes with reduced dark current and background doping

NASA Astrophysics Data System (ADS)

Maddox, S. J.; Sun, W.; Lu, Z.; Nair, H. P.; Campbell, J. C.; Bank, S. R.

2012-10-01

We reduced the room temperature dark current in an InAs avalanche photodiode by increasing the p-type contact doping, resulting in an increased energetic barrier to minority electron injection into the p-region, which is a significant source of dark current at room temperature. In addition, by improving the molecular beam epitaxy growth conditions, we reduced the background doping concentration and realized depletion widths as wide as 5 μm at reverse biases as low as 1.5 V. These improvements culminated in low-noise InAs avalanche photodiodes exhibiting a room temperature multiplication gain of ˜80, at a record low reverse bias of 12 V.

DarkBit: a GAMBIT module for computing dark matter observables and likelihoods

NASA Astrophysics Data System (ADS)

Bringmann, Torsten; Conrad, Jan; Cornell, Jonathan M.; Dal, Lars A.; Edsjö, Joakim; Farmer, Ben; Kahlhoefer, Felix; Kvellestad, Anders; Putze, Antje; Savage, Christopher; Scott, Pat; Weniger, Christoph; White, Martin; Wild, Sebastian

2017-12-01

We introduce DarkBit, an advanced software code for computing dark matter constraints on various extensions to the Standard Model of particle physics, comprising both new native code and interfaces to external packages. This release includes a dedicated signal yield calculator for gamma-ray observations, which significantly extends current tools by implementing a cascade-decay Monte Carlo, as well as a dedicated likelihood calculator for current and future experiments ( gamLike). This provides a general solution for studying complex particle physics models that predict dark matter annihilation to a multitude of final states. We also supply a direct detection package that models a large range of direct detection experiments ( DDCalc), and that provides the corresponding likelihoods for arbitrary combinations of spin-independent and spin-dependent scattering processes. Finally, we provide custom relic density routines along with interfaces to DarkSUSY, micrOMEGAs, and the neutrino telescope likelihood package nulike. DarkBit is written in the framework of the Global And Modular Beyond the Standard Model Inference Tool ( GAMBIT), providing seamless integration into a comprehensive statistical fitting framework that allows users to explore new models with both particle and astrophysics constraints, and a consistent treatment of systematic uncertainties. In this paper we describe its main functionality, provide a guide to getting started quickly, and show illustrative examples for results obtained with DarkBit (both as a stand-alone tool and as a GAMBIT module). This includes a quantitative comparison between two of the main dark matter codes ( DarkSUSY and micrOMEGAs), and application of DarkBit 's advanced direct and indirect detection routines to a simple effective dark matter model.

Genome-wide survey of B-box proteins in potato (Solanum tuberosum)-Identification, characterization and expression patterns during diurnal cycle, etiolation and de-etiolation.

PubMed

Talar, Urszula; Kiełbowicz-Matuk, Agnieszka; Czarnecka, Jagoda; Rorat, Tadeusz

2017-01-01

Plant B-box domain proteins (BBX) mediate many light-influenced developmental processes including seedling photomorphogenesis, seed germination, shade avoidance and photoperiodic regulation of flowering. Despite the wide range of potential functions, the current knowledge regarding BBX proteins in major crop plants is scarce. In this study, we identify and characterize the StBBX gene family in potato, which is composed of 30 members, with regard to structural properties and expression profiles under diurnal cycle, etiolation and de-etiolations. Based on domain organization and phylogenetic relationships, StBBX genes have been classified into five groups. Using real-time quantitative PCR, we found that expression of most of them oscillates following a 24-h rhythm; however, large differences in expression profiles were observed between the genes regarding amplitude and position of the maximal and minimal expression levels in the day/night cycle. On the basis of the time-of-day/time-of-night, we distinguished three expression groups specifically expressed during the light and two during the dark phase. In addition, we showed that the expression of several StBBX genes is under the control of the circadian clock and that some others are specifically associated with the etiolation and de-etiolation conditions. Thus, we concluded that StBBX proteins are likely key players involved in the complex diurnal and circadian networks regulating plant development as a function of light conditions and day duration.

Comparison of Measured Leakage Current Distributions with Calculated Damage Energy Distributions in HgCdTe

NASA Technical Reports Server (NTRS)

Marshall, C. J.; Ladbury, R.; Marshall, P. W.; Reed, R. A.; Howe, C.; Weller, B.; Mendenhall, M.; Waczynski, A.; Jordan, T. M.; Fodness, B.

2006-01-01

This paper presents a combined Monte Carlo and analytic approach to the calculation of the pixel-to-pixel distribution of proton-induced damage in a HgCdTe sensor array and compares the results to measured dark current distributions after damage by 63 MeV protons. The moments of the Coulombic, nuclear elastic and nuclear inelastic damage distribution were extracted from Monte Carlo simulations and combined to form a damage distribution using the analytic techniques first described in [I]. The calculations show that the high energy recoils from the nuclear inelastic reactions (calculated using the Monte Car10 code MCNPX [2]) produce a pronounced skewing of the damage energy distribution. The nuclear elastic component (also calculated using the MCNPX) has a negligible effect on the shape of the damage distribution. The Coulombic contribution was calculated using MRED [3,4], a Geant4 [4,5] application. The comparison with the dark current distribution strongly suggests that mechanisms which are not linearly correlated with nonionizing damage produced according to collision kinematics are responsible for the observed dark current increases. This has important implications for the process of predicting the on-orbit dark current response of the HgCdTe sensor array.

Influence of resin cement shade on the color and translucency of ceramic veneers

PubMed Central

HERNANDES, Daiana Kelly Lopes; ARRAIS, Cesar Augusto Galvão; de LIMA, Erick; CESAR, Paulo Francisco; RODRIGUES, José Augusto

2016-01-01

ABSTRACT Objective This in vitro study evaluated the effect of two different shades of resin cement (RC- A1 and A3) layer on color change, translucency parameter (TP), and chroma of low (LT) and high (HT) translucent reinforced lithium disilicate ceramic laminates. Material and Methods One dual-cured RC (Variolink II, A1- and A3-shade, Ivoclar Vivadent) was applied to 1-mm thick ceramic discs to create thin RC films (100 µm thick) under the ceramics. The RC was exposed to light from a LED curing unit. Color change (ΔE) of ceramic discs was measured according to CIEL*a*b* system with a standard illuminant D65 in reflectance mode in a spectrophotometer, operating in the light range of 360-740 nm, equipped with an integrating sphere. The color difference between black (B) and white (W) background readings was used for TP analysis, while chroma was calculated by the formula C* ab=(a*2+b*2)½. ΔE of 3.3 was set as the threshold of clinically unacceptable. The results were evaluated by two-way ANOVA followed by Tukey's post hoc test. Results HT ceramics showed higher ΔE and higher TP than LT ceramics. A3-shade RC promoted higher ΔE than A1-shade cement, regardless of the ceramic translucency. No significant difference in TP was noted between ceramic discs with A1- and those with A3-shade cement. Ceramic with underlying RC showed lower TP than discs without RC. HT ceramics showed lower chroma than LT ceramics, regardless of the resin cement shade. The presence of A3-shade RC resulted in higher chroma than the presence of A1-shade RC. Conclusions Darker underlying RC layer promoted more pronounced changes in ceramic translucency, chroma, and shade of high translucent ceramic veneers. These differences may not be clinically differentiable. PMID:27556211

Influence of resin cement shade on the color and translucency of ceramic veneers.

PubMed

Hernandes, Daiana Kelly Lopes; Arrais, Cesar Augusto Galvão; Lima, Erick de; Cesar, Paulo Francisco; Rodrigues, José Augusto

2016-01-01

This in vitro study evaluated the effect of two different shades of resin cement (RC- A1 and A3) layer on color change, translucency parameter (TP), and chroma of low (LT) and high (HT) translucent reinforced lithium disilicate ceramic laminates. One dual-cured RC (Variolink II, A1- and A3-shade, Ivoclar Vivadent) was applied to 1-mm thick ceramic discs to create thin RC films (100 µm thick) under the ceramics. The RC was exposed to light from a LED curing unit. Color change (ΔE) of ceramic discs was measured according to CIEL*a*b* system with a standard illuminant D65 in reflectance mode in a spectrophotometer, operating in the light range of 360-740 nm, equipped with an integrating sphere. The color difference between black (B) and white (W) background readings was used for TP analysis, while chroma was calculated by the formula C*ab=(a*2+b*2)½. ΔE of 3.3 was set as the threshold of clinically unacceptable. The results were evaluated by two-way ANOVA followed by Tukey's post hoc test. HT ceramics showed higher ΔE and higher TP than LT ceramics. A3-shade RC promoted higher ΔE than A1-shade cement, regardless of the ceramic translucency. No significant difference in TP was noted between ceramic discs with A1- and those with A3-shade cement. Ceramic with underlying RC showed lower TP than discs without RC. HT ceramics showed lower chroma than LT ceramics, regardless of the resin cement shade. The presence of A3-shade RC resulted in higher chroma than the presence of A1-shade RC. Darker underlying RC layer promoted more pronounced changes in ceramic translucency, chroma, and shade of high translucent ceramic veneers. These differences may not be clinically differentiable.

Prevalence of Colour Vision Anomalies Amongst Dental Professionals and its Effect on Shade Matching of Teeth.

PubMed

Khosla, Amrit; Maini, Anuj Paul; Wangoo, Anuj; Singh, Sukhman; Mehar, Damanpreet Kaur

2017-01-01

The success of a restoration is dependent on accurate shade matching of teeth leading to studies evaluating the factors affecting the perception of shades. Colour vision anomalies including colour blindness have been found to exist in the population and it has been thought to be a potential factor affecting the colour perception ability. The present study was done to evaluate the prevalence of colour vision anomalies and its effect on matching of shades of teeth. A total of 147 dental professionals were randomly selected for the study and were first tested for visual acuity using the Snellen's Eye Chart so as to carry on the study with only those operators who had a vision of 6/6. Then, the Ishihara's colour charts were used to test the operators for colour vision handicap. In the last stage of the study, test for accuracy of shade selection was done using the Vitapan Classical shade guide. The shade guide tabs were covered to avoid bias. Percentage was used to calculate the prevalence of colour vision handicap and its effect on matching of shades of teeth as compared to normal vision, which was evaluated using Chi square test. Nineteen operators had colour vision anomalies out of hundred operators and only two operators presented with colour blindness. Colour vision anomaly was more prevalent than colour blindness and it was also found that it was more prevalent in males than females. The difference between the accuracy of shade matching between the operators with normal vision and colour vision defect and operators with normal vision and colour blindness was statistically not significant. Colour blindness and colour vision handicap are rare conditions, with the latter being more common in the population. According to our study, it was concluded that no statistically significant difference existed amongst the operators with normal vision and colour vision anomaly or operators with normal vision and colour blindness during the matching of shades of teeth.

Species abundance and potential biological control services in shade vs. sun coffee in Puerto Rico

USGS Publications Warehouse

Borkhataria, Rena R.; Collazo, Jaime A.; Groom, Martha J.

2012-01-01

Birds, lizards and insects were surveyed in three sun and three shade coffee plantations in Puerto Rico to provide a comprehensive comparison of biodiversity between plantations types and to identify potential interrelationships (e.g., biological or natural control services) between members of each taxon and coffee pests. Abundance of avian species, including insectivorous species, was significantly higher in shade coffee. Anolis cristatellus and A. stratulus were significantly more abundant in sun plantations whereas A. gundlachi and A. evermanni were detected more frequently in shade plantations. Insects in the orders Coleoptera, Diptera, Hemiptera, Hymenoptera, Lepidoptera, Neuroptera, and Psocoptera were significantly more abundant in shade coffee, while orthopterans were more abundant in sun. The coffee leaf miner (Leucoptera coffeela) and the flatid planthopper (Petrusa epilepsis) did not differ significantly between plantation types, nor did the abundance of the wasp complex that parasitizes the coffee leaf miner. These findings confirmed that shade plantations harbor a wide array of elements of biodiversity; but sun plantations may also harbor many elements of biodiversity, and in some cases, in higher abundance than in shade plantations.

Seasonal contrasts in the response of coffee ants to agroforestry shade-tree management.

PubMed

Teodoro, A V; Sousa-Souto, L; Klein, A-M; Tscharntke, T

2010-12-01

In many tropical landscapes, agroforestry systems are the last forested ecosystems, providing shade, having higher humidity, mitigating potential droughts, and possessing more species than any other crop system. Here, we tested the hypothesis that higher levels of shade and associated humidity in agroforestry enhance coffee ant richness more during the dry than rainy season, comparing ant richness in 22 plots of three coffee agroforestry types in coastal Ecuador: simple-shade agroforests (intensively managed with low tree species diversity), complex-shade agroforests (extensively managed with intermediate tree species diversity) and abandoned coffee agroforests (abandoned for 10-15 yr and resembling secondary forests). Seasonality affected responses of ant richness but not composition to agroforestry management, in that most species were observed in abandoned coffee agroforests in the dry season. In the rainy season, however, most species were found in simple-shade agroforests, and complex agroforestry being intermediate. Foraging coffee ants species composition did not change differently according to agroforestry type and season. Results show that shade appears to be most important in the dry seasons, while a mosaic of different land-use types may provide adequate environmental conditions to ant species, maximizing landscape-wide richness throughout the year. © 2010 Entomological Society of America

Effect of shade on Arabica coffee berry disease development: Toward an agroforestry system to reduce disease impact.

PubMed

Mouen Bedimo, J A; Njiayouom, I; Bieysse, D; Ndoumbè Nkeng, M; Cilas, C; Nottéghem, J L

2008-12-01

Coffee berry disease (CBD), caused by Colletotrichum kahawae, is a major constraint for Arabica coffee cultivation in Africa. The disease is specific to green berries and can lead to 60% harvest losses. In Cameroon, mixed cropping systems of coffee with other crops, such as fruit trees, are very widespread agricultural practices. Fruit trees are commonly planted at random on coffee farms, providing a heterogeneous shading pattern for coffee trees growing underneath. Based on a recent study of CBD, it is known that those plants can reduce disease incidence. To assess the specific effect of shade, in situ and in vitro disease development was compared between coffee trees shaded artificially by a net and trees located in full sunlight. In the field, assessments confirmed a reduction in CBD on trees grown under shade compared with those grown in full sunlight. Artificial inoculations in the laboratory showed that shade did not have any effect on the intrinsic susceptibility of coffee berries to CBD. Coffee shading mainly acts on environmental parameters in limiting disease incidence. In addition to reducing yield losses, agroforestry system may also be helpful in reducing chemical control of the disease and in diversifying coffee growers' incomes.

Dark sector shining through 750 GeV dark Higgs boson at the LHC

NASA Astrophysics Data System (ADS)

Ko, P.; Nomura, Takaaki

2016-07-01

We consider a dark sector with SU(3)C × U(1)Y × U(1)X and three families of dark fermions that are chiral under dark U(1)X gauge symmetry, whereas scalar dark matter X is the SM singlet. U(1)X dark symmetry is spontaneously broken by nonzero VEV of dark Higgs field 〈 Φ 〉, generating the masses of dark fermions and dark photon Z‧. The resulting dark Higgs boson ϕ can be produced at the LHC by dark quark loop (involving 3 generations) and will decay into a pair of photon through charged dark fermion loop. Its decay width can be easily ∼ 45 GeV due to its possible decays into a pair of dark photon, which is not strongly constrained by the current LHC searches pp → ϕ →Z‧Z‧ followed by Z‧ decays into the SM fermion pairs. The scalar DM can achieve thermal relic density without conflict with direct detection bound or the invisible ϕ decay into a pair of DM.

Proton effects on low noise and high responsivity silicon-based photodiodes for space environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pedroza, Guillaume; Gilard, Olivier; Bourqui, Marie-Lise

A series of proton irradiations has been carried out on p-n silicon photodiodes for the purpose of assessing the suitability of these devices for the European Galileo space mission. The irradiations were performed at energies of 60, 100, and 150 MeV with proton fluences ranging from 1.7x10{sup 10} to 1x10{sup 11} protons/cm{sup 2}. Dark current, spectral responsivity, and dark current noise were measured before and after each irradiation step. We observed an increase in both dark current, dark current noise, and noise equivalent power and a drop of the spectral responsivity with increasing displacement damage dose. An analytical model hasmore » been developed to investigate proton damage effects through the modeling of the electro-optical characteristics of the photodiode. Experimental degradations were successfully explained taking into account the degradation of the minority carrier diffusion length in the N-region of the photodiode. The degradation model was then applied to assess the end-of-life performance of these devices in the framework of the Galileo mission.« less

Analysis of Dark Current in BRITE Nanostellite CCD Sensors †

PubMed Central

Popowicz, Adam

2018-01-01

The BRightest Target Explorer (BRITE) is the pioneering nanosatellite mission dedicated for photometric observations of the brightest stars in the sky. The BRITE charge coupled device (CCD) sensors are poorly shielded against extensive flux of energetic particles which constantly induce defects in the silicon lattice. In this paper we investigate the temporal evolution of the generation of the dark current in the BRITE CCDs over almost four years after launch. Utilizing several steps of image processing and employing normalization of the results, it was possible to obtain useful information about the progress of thermal activity in the sensors. The outcomes show a clear and consistent linear increase of induced damage despite the fact that only about 0.14% of CCD pixels were probed. By performing the analysis of temperature dependencies of the dark current, we identified the observed defects as phosphorus-vacancy (PV) pairs, which are common in proton irradiated CCD matrices. Moreover, the Meyer-Neldel empirical rule was confirmed in our dark current data, yielding EMN=24.8 meV for proton-induced PV defects. PMID:29415471

France, Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2003-01-01

This image of France was generated with data from the Shuttle Radar Topography Mission (SRTM). For this broad view the resolution of the data was reduced to 6 arcseconds (about 185 meters north-south and 127 meters east-west), resampled to a Mercator projection, and the French border outlined. Even at this decreased resolution the variety of landforms comprising the country is readily apparent.

The upper central part of this scene is dominated by the Paris Basin, which consists of a layered sequence of sedimentary rocks. Fertile soils over much of the area make good agricultural land. The Normandie coast to the upper left is characterized by high, chalk cliffs, while the Brittany coast (the peninsula to the left) is highly indented where deep valleys were drowned by the sea, and the Biscay coast to the southwest is marked by flat, sandy beaches.

To the south, the Pyrenees form a natural border between France and Spain, and the south-central part of the country is dominated by the ancient Massif Central. Subject to volcanism that has only subsided in the last 10,000 years, these central mountains are separated from the Alps by the north-south trending Rhone River Basin.

Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise,Washington, D.C.

Location: 42 to 51.5 degrees North latitude, 5.5 West to 8 degrees East longitude Orientation: North toward the top, Mercator projection Image Data: shaded and colored SRTM elevation model Original Data Resolution: SRTM 1 arcsecond (about 30 meters or 98 feet) Date Acquired: February 2000

Alpine Fault, New Zealand, SRTM Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2005-01-01

The Alpine fault runs parallel to, and just inland of, much of the west coast of New Zealand's South Island. This view was created from the near-global digital elevation model produced by the Shuttle Radar Topography Mission (SRTM) and is almost 500 kilometers (just over 300 miles) wide. Northwest is toward the top. The fault is extremely distinct in the topographic pattern, nearly slicing this scene in half lengthwise.

In a regional context, the Alpine fault is part of a system of faults that connects a west dipping subduction zone to the northeast with an east dipping subduction zone to the southwest, both of which occur along the juncture of the Indo-Australian and Pacific tectonic plates. Thus, the fault itself constitutes the major surface manifestation of the plate boundary here. Offsets of streams and ridges evident in the field, and in this view of SRTM data, indicate right-lateral fault motion. But convergence also occurs across the fault, and this causes the continued uplift of the Southern Alps, New Zealand's largest mountain range, along the southeast side of the fault.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast (image top to bottom) direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 495 kilometers (307 miles) by 162 kilometers (100 miles) Location: 43.2 degrees South latitude, 170.5 degrees East longitude Orientation: Northwest toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

Davenport Ranges, Northern Territory, Australia, SRTM Shaded Relief and Colored Height

NASA Technical Reports Server (NTRS)

2005-01-01

The Davenport Ranges of central Australia have been inferred to be among the oldest persisting landforms on Earth, founded on the belief that the interior of Australia has been tectonically stable for at least 700 million years. New rock age dating techniques indicate that substantial erosion has probably occurred over that time period and that the landforms are not nearly that old, but landscape evolution certainly occurs much slower here (at least now) than is typical across Earth's surface.

Regardless of their antiquity, the Davenport Ranges exhibit a striking landform pattern as shown in this display of elevation data from the Shuttle Radar Topography Mission (SRTM). Quartzites and other erosion resistant strata form ridges within anticlinal (arched up) and synclinal (arched down) ovals and zigzags. These structures, if not the landforms, likely date back at least hundreds of millions of years, to a time when tectonic forces were active. Maximum local relief is only about 60 meters (about 200 feet), which is enough to contrast greatly with the extremely low relief surrounding terrain.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northeast-southwest (image top to bottom) direction, so that northeast slopes appear bright and southwest slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 270 kilometers (168 miles) by 145 kilometers (90 miles) Location: 20.9 degrees South latitude, 134.9 degrees East longitude Orientation: Northeast toward the top Image Data: Shaded and colored SRTM elevation model Date Acquired: February 2000

SRTM Colored Height and Shaded Relief: Pinon Canyon region, Colorado

NASA Technical Reports Server (NTRS)

2001-01-01

Erosional features are prominent in this view of southern Colorado taken by the Shuttle Radar Topography Mission (SRTM). The area covers about 20,000 square kilometers and is located about 50 kilometers south of Pueblo, Colorado. The prominent mountains near the left edge of the image are the Spanish Peaks, remnants of a 20 million year old volcano. Rising 2,100 meters (7,000 ft) above the plains to the east, these igneous rock formations with intrusions of eroded sedimentary rock historically served as guiding landmarks for travelers on the Mountain Branch of the Santa Fe Trail.

Near the center of the image is the Pinon Canyon Maneuver Site, a training area for soldiers of the U.S. Army from nearby Fort Carson. The site supports a diverse ecosystem with large numbers of big and small game, fisheries, non-game wildlife, forest, range land and mineral resources. It is bounded on the east by the dramatic topography of the Purgatoire River Canyon, a 100 meter (328 foot) deep scenic red canyon with flowing streams, sandstone formations, and exposed geologic processes.

Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction. Southern slopes appear bright and northern slopes appear dark. Color coding is directly related to topographic height, with blue and green at the lower elevations, rising through yellow and brown to white at the highest elevations.

Elevation data used in this image was acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on February 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR)that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter-long (200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between the National Aeronautics and Space Administration (NASA), the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense, and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Earth Science Enterprise, Washington, DC.

Size: 177.8 x 111.3 kilometers ( 110.5 x 69.2 miles) Location: 37.5 deg. North lat., 104 deg. West lon. Orientation: North toward the top Image Data: Shaded and colored SRTM elevation model Original Data Resolution: SRTM 1 arcsecond (30 meters or 99 feet) Date Acquired: February 2000

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domengie, F., E-mail: florian.domengie@st.com; Morin, P.; Bauza, D.

We propose a model for dark current induced by metallic contamination in a CMOS image sensor. Based on Shockley-Read-Hall kinetics, the expression of dark current proposed accounts for the electric field enhanced emission factor due to the Poole-Frenkel barrier lowering and phonon-assisted tunneling mechanisms. To that aim, we considered the distribution of the electric field magnitude and metal atoms in the depth of the pixel. Poisson statistics were used to estimate the random distribution of metal atoms in each pixel for a given contamination dose. Then, we performed a Monte-Carlo-based simulation for each pixel to set the number of metalmore » atoms the pixel contained and the enhancement factor each atom underwent, and obtained a histogram of the number of pixels versus dark current for the full sensor. Excellent agreement with the dark current histogram measured on an ion-implanted gold-contaminated imager has been achieved, in particular, for the description of the distribution tails due to the pixel regions in which the contaminant atoms undergo a large electric field. The agreement remains very good when increasing the temperature by 15 °C. We demonstrated that the amplification of the dark current generated for the typical electric fields encountered in the CMOS image sensors, which depends on the nature of the metal contaminant, may become very large at high electric field. The electron and hole emissions and the resulting enhancement factor are described as a function of the trap characteristics, electric field, and temperature.« less

Relevant optical properties for direct restorative materials.

PubMed

Pecho, Oscar E; Ghinea, Razvan; do Amaral, Erika A Navarro; Cardona, Juan C; Della Bona, Alvaro; Pérez, María M

2016-05-01

To evaluate relevant optical properties of esthetic direct restorative materials focusing on whitened and translucent shades. Enamel (E), body (B), dentin (D), translucent (T) and whitened (Wh) shades for E (WhE) and B (WhB) from a restorative system (Filtek Supreme XTE, 3M ESPE) were evaluated. Samples (1 mm thick) were prepared. Spectral reflectance (R%) and color coordinates (L*, a*, b*, C* and h°) were measured against black and white backgrounds, using a spectroradiometer, in a viewing booth, with CIE D65 illuminant and d/0° geometry. Scattering (S) and absorption (K) coefficients and transmittance (T%) were calculated using Kubelka-Munk's equations. Translucency (TP) and opalescence (OP) parameters and whiteness index (W*) were obtained from differences of CIELAB color coordinates. R%, S, K and T% curves from all shades were compared using VAF (Variance Accounting For) coefficient with Cauchy-Schwarz inequality. Color coordinates and optical parameters were statistically analyzed using one-way ANOVA, Tukey's test with Bonferroni correction (α=0.0007). Spectral behavior of R% and S were different for T shades. In addition, T shades showed the lowest R%, S and K values, as well as the highest T%, TP an OP values. In most cases, WhB shades showed different color and optical properties (including TP and W*) than their corresponding B shades. WhE shades showed similar mean W* values and higher mean T% and TP values than E shades. When using whitened or translucent composites, the final color is influenced not only by the intraoral background but also by the color and optical properties of multilayers used in the esthetic restoration. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effects of combining ozone and hydrogren peroxide on tooth bleaching: A clinical study.

PubMed

Al-Omiri, Mahmoud K; Hassan, Ra'ed S Abul; AlZarea, Bader K; Lynch, Edward

2016-10-01

The purpose of this study was to evaluate the efficiency of bleaching after combining ozone and 38% H2O2 in comparison to the sole use of 38% H2O2. Consecutive 26 participants (13 males and 13 females) were recruited into this study. They were randomly allocated into 2 groups (n=13 for each group). In group 1 (test group); the participants' upper anterior teeth were treated with 38% H2O2 for 20min then the teeth were exposed to ozone for 60s (healOzone(®) X4, KaVo Dental, Biberach, Germany). In group 2 (controls); the upper anterior teeth were treated with 20min of 38% H2O2 only. The shade of teeth was evaluated by recording the L* a* b* values and Vita Classic shades at study baseline and after bleaching in both groups. The statistically significant changes were set at P≤0.05. Tooth sensitivity and teeth shades were comparable between groups at study baseline (p>0.05). Controls reported more tooth sensitivity following bleaching (p<0.001). Teeth achieved better Vita shades, higher L* values (lighter shades), and lower a* and b* values (lighter shades) after bleaching in both groups (P≤0.05). However, teeth bleached with H2O2 and ozone achieved better Vita shades, higher L* values and lower a* values (lighter shades) than those bleached with H2O2 alone (p<0.001). Changes in b* values were not significantly different between groups. Bleaching with 38% H2O2 for 20min followed by 60s of ozone application would result in teeth with lighter shades than bleaching with 38% H2O2 alone. Copyright © 2016 Elsevier Ltd. All rights reserved.

Is shade beneficial for mediterranean shrubs experiencing periods of extreme drought and late-winter frosts?

PubMed

Valladares, Fernando; Zaragoza-Castells, Joana; Sánchez-Gómez, David; Matesanz, Silvia; Alonso, Beatriz; Portsmuth, Angelika; Delgado, Antonio; Atkin, Owen K

2008-12-01

Plants are naturally exposed to multiple, frequently interactive stress factors, most of which are becoming more severe due to global change. Established plants have been reported to facilitate the establishment of juvenile plants, but net effects of plant-plant interactions are difficult to assess due to complex interactions among environmental factors. An investigation was carried out in order to determine how two dominant evergreen shrubs (Quercus ilex and Arctostaphylos uva-ursi) co-occurring in continental, Mediterranean habitats respond to multiple abiotic stresses and whether the shaded understorey conditions ameliorate the negative effects of drought and winter frosts on the physiology of leaves. Microclimate and ecophysiology of sun and shade plants were studied at a continental plateau in central Spain during 2004-2005, with 2005 being one of the driest and hottest years on record; several late-winter frosts also occurred in 2005. Daytime air temperature and vapour pressure deficit were lower in the shade than in the sun, but soil moisture was also lower in the shade during the spring and summer of 2005, and night-time temperatures were higher in the shade. Water potential, photochemical efficiency, light-saturated photosynthesis, stomatal conductance and leaf 13C composition differed between sun and shade individuals throughout the seasons, but differences were species specific. Shade was beneficial for leaf-level physiology in Q. ilex during winter, detrimental during spring for both species, and of little consequence in summer. The results suggest that beneficial effects of shade can be eclipsed by reduced soil moisture during dry years, which are expected to be more frequent in the most likely climate change scenarios for the Mediterranean region.

Is Shade Beneficial for Mediterranean Shrubs Experiencing Periods of Extreme Drought and Late-winter Frosts?

PubMed Central

Valladares, Fernando; Zaragoza-Castells, Joana; Sánchez-Gómez, David; Matesanz, Silvia; Alonso, Beatriz; Portsmuth, Angelika; Delgado, Antonio; Atkin, Owen K.

2008-01-01

Background and Aims Plants are naturally exposed to multiple, frequently interactive stress factors, most of which are becoming more severe due to global change. Established plants have been reported to facilitate the establishment of juvenile plants, but net effects of plant–plant interactions are difficult to assess due to complex interactions among environmental factors. An investigation was carried out in order to determine how two dominant evergreen shrubs (Quercus ilex and Arctostaphylos uva-ursi) co-occurring in continental, Mediterranean habitats respond to multiple abiotic stresses and whether the shaded understorey conditions ameliorate the negative effects of drought and winter frosts on the physiology of leaves. Methods Microclimate and ecophysiology of sun and shade plants were studied at a continental plateau in central Spain during 2004–2005, with 2005 being one of the driest and hottest years on record; several late-winter frosts also occurred in 2005. Key Results Daytime air temperature and vapour pressure deficit were lower in the shade than in the sun, but soil moisture was also lower in the shade during the spring and summer of 2005, and night-time temperatures were higher in the shade. Water potential, photochemical efficiency, light-saturated photosynthesis, stomatal conductance and leaf 13C composition differed between sun and shade individuals throughout the seasons, but differences were species specific. Shade was beneficial for leaf-level physiology in Q. ilex during winter, detrimental during spring for both species, and of little consequence in summer. Conclusions The results suggest that beneficial effects of shade can be eclipsed by reduced soil moisture during dry years, which are expected to be more frequent in the most likely climate change scenarios for the Mediterranean region. PMID:18819947

Rationale, design, and baseline data of a cross-national randomized trial on the effect of built shade in public parks for sun protection.

PubMed

Buller, David B; Dobbinson, Suzanne; English, Dallas R; Wakefield, Melanie; Buller, Mary Klein

2017-04-01

Environments can be structured to reduce solar ultraviolet radiation (UV) exposure to prevent skin cancer. A prospective randomized trial is being conducted to test whether introducing shade sails in passive recreation areas (PRAs) in public parks will increase use and decrease UV exposure in the shaded compared to unshaded PRAs. Shade effects will be compared between Melbourne, Australia and Denver, USA. The trial enrolled 145 public parks with PRAs suitable for shade construction and randomized parks to intervention or control in a 1:3 ratio. Use of PRAs and UV levels were recorded at each park by trained observers during 30-minute periods on four weekend days in each of two summers (pretest and posttest). Shade sails were constructed between the summers. Given low numbers of users at pretest, the outcome measure was modified to use of the PRA (use vs. no use) and unit of analysis to the individual observation. Observations (n=580) occurred on average 29days from the summer solstice and 55min from solar noon in warm weather (mean=26.2°C) with some cloud cover but only slight or no wind. Typically, PRAs had benches and picnic tables and were located near playgrounds. PRAs were in use during 13.3% of observations (mean=0.41 users). UV over 30-minutes at the PRA boundary (mean=3.2 standard erythemal dose [SED]) and center (mean=3.3 SED) was high. Shade for skin cancer prevention has been understudied. This study will address this gap by determining whether purpose-built shade structures promote greater use of shaded areas within public parks. Copyright © 2017 Elsevier Inc. All rights reserved.

Analysis of Shade Matching in Natural Dentitions Using Intraoral Digital Spectrophotometer in LED and Filtered LED Light Sources.

PubMed

Chitrarsu, Vijai Krishnan; Chidambaranathan, Ahila Singaravel; Balasubramaniam, Muthukumar

2017-10-31

To evaluate the shade matching capabilities in natural dentitions using Vita Toothguide 3D-Master and an intraoral digital spectrophotometer (Vita Easyshade Advance 4.0) in various light sources. Participants between 20 and 40 years old with natural, unrestored right maxillary central incisors, no history of bleaching, orthodontic treatment, or malocclusion and no rotations were included. According to their shades, subjects were randomly selected and grouped into A1, A2, and A3. A total of 100 participants (50 male and 50 female) in each group were chosen for this study. Shade selection was made between 10 am and 2 pm for all light sources. The same examiner selected the shade of natural teeth with Vita Toothguide 3D-Master under natural light within 2 minutes. Once the Vita Toothguide 3D-Masterwas matched with the maxillary right central incisor, the L*, a*, and b* values, chroma, and hue were recorded with Vita Easyshade Advance 4.0 by placing it on the shade tab under the same light source. The values were statistically analyzed using one-way ANOVA and Tukey's HSD post hoc test with SPSS v22.0 software. The mean ∆E* ab values for shades A1, A2, and A3 for groups 1, 2, and 3 were statistically significantly different from each other (p < 0.001). The intraoral digital spectrophotometer showed statistically significant differences in shade matching compared to Vita Toothguide 3D-Master. Incandescent light showed more accurate shade matching than the filtered LED, LED, and daylight. © 2017 by the American College of Prosthodontists.

Rationale, Design, and Baseline Data of a Cross-national Randomized Trial on the Effect of Built Shade in Public Parks for Sun Protection

PubMed Central

Buller, David B.; Dobbinson, Suzanne; English, Dallas R.; Wakefield, Melanie; Buller, Mary Klein

2017-01-01

Environments can be structured to reduce solar ultraviolet radiation (UV) exposure to prevent skin cancer. A prospective randomized trial is being conducted to test whether introducing shade sales in passive recreation areas (PRAs) in public parks will increase use and decrease UV exposure in the shaded compared to unshaded PRAs. Shade effects will be compared between Melbourne, Australia and Denver, USA. The trial enrolled 144 public parks with PRAs suitable for shade construction and randomized parks to intervention or control in a 1:3 ratio. Use of PRAs and UV levels were recorded at each park by trained observers during 30-minute periods on four weekend days in each of two summers (pretest and posttest). Shade sails were constructed between the summers. Given low numbers of users at pretest, the outcome measure was modified to use of the PRA (use v. no use) and unit of analysis to the individual observation. Observations (n=580) occurred on average 29 days from the summer solstice and 55 minutes from solar noon in warm weather (mean=26.2°C) with some cloud cover but only slight or no wind. Typically, PRAs had benches and picnic tables and were located near playgrounds. PRAs were in use during 13.3% of observations (mean=0.41 users). UV over 30-minutes at the PRA boundary (mean=3.2 standard erythemal dose [SED]) and center (mean=3.3 SED) was high. Shade for skin cancer prevention has been understudied. This study will address this gap by determining whether purpose-built shade structures promote greater use of shaded areas within public parks. PMID:28185996

Modeling Hydrological Services in Shade Grown Coffee Systems: Case Study of the Pico Duarte Region of the Dominican Republic

NASA Astrophysics Data System (ADS)

Erickson, J. D.; Gross, L.; Agosto Filion, N.; Bagstad, K.; Voigt, B. G.; Johnson, G.

2010-12-01

The modification of hydrologic systems in coffee-dominated landscapes varies widely according to the degree of shade trees incorporated in coffee farms. Compared to mono-cropping systems, shade coffee can produce both on- and off-farm benefits in the form of soil retention, moderation of sediment transport, and lower hydropower generating costs. The Pico Duarte Coffee Region and surrounding Madres de Las Aguas (Mother of Waters) Conservation Area in the Dominican Republic is emblematic of the challenges and opportunities of ecosystem service management in coffee landscapes. Shade coffee poly-cultures in the region play an essential role in ensuring ecosystem function to conserve water resources, as well as provide habitat for birds, sequester carbon, and provide consumptive resources to households. To model the provision, use, and flow of ecosystem services from coffee farms in the region, an application of the Artificial Intelligence for Ecosystem Services (ARIES) model was developed with particular focus on sediment regulation. ARIES incorporates an array of techniques from data mining, image analysis, neural networks, Bayesian statistics, information theory, and expert systems to model the production, delivery, and demand for ecosystem services. Geospatial data on slope, soils, and vegetation cover is combined with on-farm data collection of coffee production, tree diversity, and intercropping of household food. Given hydropower production and river recreation in the region, the management of sedimentation through on-farm practices has substantial, currently uncompensated value that has received recent attention as the foundation for a payment for ecosystem services system. Scenario analysis of the implications of agro-forestry management choices on farmer livelihoods and the multiple beneficiaries of farm-provided hydrological services provide a foundation for ongoing discussions in the region between local, national, and international interests.

Hypothenemus hampei (Coleoptera: Curculionidae) and its interactions with Azteca instabilis and Pheidole synanthropica (Hymenoptera: Formicidae) in a shade coffee agroecosystem.

PubMed

Jiménez-Soto, Estelí; Cruz-Rodríguez, Juan A; Vandermeer, John; Perfecto, Ivette

2013-10-01

The coffee berry borer is currently the most important insect pest of coffee worldwide. In shaded coffee farms such as Finca Irlanda in Chiapas, Mexico, natural enemies limit coffee berry borer and potentially prevent outbreaks. This research aimed to determine the effect of ants on coffee berry borer damage and to describe behaviors of Azteca instabilis F. Smith and Pheidole synanthropica (Longino 2009) when encountering the coffee berry borer. To these ends, an ant survey was conducted in a 2,500-m(2) plot within the farm. A 4- by 4-m coordinate system was established, and the coffee plant or shade tree closest to the coordinate point was sampled using tuna fish for a total of 168 coffee plants and 46 shade trees sampled. In addition, up to 100 berries were harvested from 138 coffee plants to measure damage and verify the presence of the coffee berry borer. Behavior was determined in the field by placing live coffee berry borer adults on berries and video recording all attacks. Results showed that plants with ants had less percentage of damaged berries and shorter coffee berry borer galleries than plants without ants. However, the length of galleries in plants with A. instabilis showed no significant differences from plants without ants. P. synanthropica was observed carrying coffee berry borer to the nest in 50% of the cases, whereas A. instabilis threw coffee berry borer off of the coffee plant in 79% of the cases. Results indicate that the presence of these species of ants reduce coffee berry borer damage and suggest that different behaviors could explain the pattern of coffee berry borer attack in this agroecosystem.

Hydrocarbon emissions from twelve urban shade trees of the Los Angeles, California, Air Basin

NASA Astrophysics Data System (ADS)

Corchnoy, Stephanie B.; Arey, Janet; Atkinson, Roger

The large-scale planting of shade trees in urban areas to counteract heat-island effects and to minimize energy use is currently being discussed. Among the costs to be considered in a cost/benefit analysis of such a program is the potential for additional reactive organic compounds in the atmosphere due to emissions from these trees. In this program, 15 species of potential shade trees for the Los Angeles Air Basin were studied and emission rates were determined for 11 of these trees, with one further tree (Crape myrtle) exhibiting no detectable emissions. The emission rates normalized to dry leaf weight and corrected to 30°C were (in μg g -1 h -1), ranked from lowest to highest emission rate: Crape myrtle, none detected; Camphor, 0.03; Aleppo pine, 0.15; Deodar cedar, 0.29; Italian Stone pine, 0.42; Monterey pine, 0.90; Brazilian pepper, 1.3; Canary Island pine, 1.7; Ginkgo, 3.0; California pepper, 3.7; Liquidambar, 37; Carrotwood, 49. In addition to the emission rates per unit biomass, the biomass per tree must be factored into any assessment of the relative merits of the various trees, since some trees have higher biomass constants than others. The present data shows that there are large differences in emission rates among different tree species and this should be factored into decision-making as to which shade trees to plant. Based solely on the presently determined emission rates, the Crape myrtle and Camphor tree are good choices for large-scale planting, while the Carrotwood tree and Liquidambar are poor choices due to their high isoprene emission rates.

Growth, allometry and shade tolerance of understory saplings of four subalpine conifers in central Japan.

PubMed

Takahashi, Koichi; Obata, Yoshiko

2014-03-01

The conifers Abies veitchii, A. mariesii, Picea jezoensis var. hondoensis, Tsuga diversifolia dominate in subalpine forests in central Japan. We expected that species differences in shade tolerance and in aboveground and belowground architecture are important for their coexistence. We examined net production and carbon allocation of understory saplings. Although the four species allocated similar amounts of biomass to roots at a given trunk height, the root-zone area of T. diversifolia was greater than that of the three other species. T. diversifolia often dominates shallow soil sites, such as ridge and rocky slopes, and, therefore, a wide spread of lateral roots would be an adaptation to such edaphic conditions. Crown width and leaf and branch mass were greatest for T. diversifolia and A. mariesii, followed in order by A. veitchii and P. jezoensis var. hondoensis. Although leaf mass of P. jezoensis var. hondoensis was lowest among the four species, species differences were not found in the net production per sapling because net production per leaf mass was greatest for P. jezoensis var. hondoensis. The leaf lifespan was longer in the order A. mariesii, T. diversifolia, P. jezoensis var. hondoensis and A. veitchii. The minimum rate of net production per leaf mass required to maintain the current sapling leaf mass (MRNP(LM)) was lowest in A. mariesii and T. diversifolia, and increased in the order of A. veitchii and P. jezoensis var. hondoensis. A. mariesii and T. diversifolia may survive in shade conditions by a lower MRNP(LM) than the two other species. Therefore, species differences in aboveground and belowground architecture and MRNPLM reflected their shade tolerance and regeneration strategies, which contribute to their coexistence.

Shade images of forested areas obtained from Landsat MSS data

NASA Technical Reports Server (NTRS)

Shimabukuro, Yosio Edemir; Smith, James A.

1989-01-01

The objective of this report is to generate a shade (shadow) image of forested areas from Landsat MSS data by implementing a linear mixing model, where shadow is considered as one of the primary components in a pixel. The shade images are related to the observed variation in forest structure; i.e., the proportion of inferred shadow in a pixel is related to different forest ages, forest types, and tree crown cover. The constrained least-squares method is used to generate shade images for forest of eucalyptus and vegetation of 'cerrado' over the Itapeva study area in Brazil. The resulted shade images may explain the difference on ages for forest of eucalyptus and the difference on tree crown cover for vegetation of cerrado.

[Effects of shading on two Sphagnum species growth and their interactions].

PubMed

Ma, Jin-Ze; Bu, Zhao-Jun; Zheng, Xing-Xing; Li, Shan-Lin; Zeng, Jing; Zhao, Gao-Lin

2012-02-01

Taking Sphagnum palustre and S. fallax as test materials, this paper studied their growth and interactions under shading. In monoculture, shading promoted the height growth of S. palustre markedly, but had no effect on the growth of S. fallax and the biomass and branching of S. palustre. In mixed culture, S. fallax suppressed the increase of biomass and branching of S. palustre, while S. palustre had no effects on S. fallax. With the increase of shading stress, the competition of neighbour on S. fallax intensified. When the stress increased further, neighbor effect on S. fallax tended to be positive. However, the effect of neighbour on S. palustre was always competitive and did not change with the increase of shading stress.

SU-F-T-554: Dark Current Effect On CyberKnife Beam Dosimetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, H; Chang, A

Purpose: All RF linear accelerators produce dark current to varying degrees when an accelerating voltage and RF input is applied in the absence of electron gun injection. This study is to evaluate how dark current from the linear accelerator of CyberKnife affect the dose in the reference dosimetry. Methods: The G4 CyberKnife system with 6MV photon beam was used in this study. Using the ion chamber and the diode detector, the dose was measured in water with varying time delay between acquiring charges and staring beam-on after applying high-voltage into the linear accelerator. The dose was measured after the timemore » delay with over the range of 0 to 120 seconds in the accelerating high-voltage mode without beam-on, applying 0, 10, 50, 100, and 200 MUs. For the measurements, the collimator of 60 mm was used and the detectors were placed at the depths of 10 cm with the source-to-surface distance of 80 cm. Results: The dark current was constant over time regardless of MU. The dose due to the dark current increased over time linearly with the R-squared value of 0.9983 up to 4.4 cGy for the time 120 seconds. In the dose rate setting of 720 MU/min, the relative dose when applying the accelerating voltage without beam-on was increased over time up to 0.6% but it was less than the leakage radiation resulted from the accelerated head. As the reference dosimetry condition, when 100 MU was delivered after 10 seconds time delay, the relative dose increased by 0.7% but 6.7% for the low MU (10 MU). Conclusion: In the dosimetry using CyberKnife system, the constant dark current affected to the dose. Although the time delay in the accelerating high-voltage mode without beam-on is within 10 seconds, the dose less than 100 cGy can be overestimated more than 1%.« less

Dark gauge bosons: LHC signatures of non-abelian kinetic mixing

DOE PAGES

Argüelles, Carlos A.; He, Xiao-Gang; Ovanesyan, Grigory; ...

2017-04-20

We consider non-abelian kinetic mixing between the Standard Model and a dark sector gauge group associated with the presence of a scalar triplet. The magnitude of the resulting dark photon coupling ϵ is determined by the ratio of the triplet vacuum expectation value, constrained to by by electroweak precision tests, to the scale Λ of the effective theory. The corresponding effective operator Wilson coefficient can be while accommodating null results for dark photon searches, allowing for a distinctive LHC dark photon phenomenology. After outlining the possible LHC signatures, we illustrate by recasting current ATLAS dark photon results into the non-abelianmore » mixing context.« less

Dark matter and the equivalence principle

NASA Technical Reports Server (NTRS)

Frieman, Joshua A.; Gradwohl, Ben-Ami

1993-01-01

A survey is presented of the current understanding of dark matter invoked by astrophysical theory and cosmology. Einstein's equivalence principle asserts that local measurements cannot distinguish a system at rest in a gravitational field from one that is in uniform acceleration in empty space. Recent test-methods for the equivalence principle are presently discussed as bases for testing of dark matter scenarios involving the long-range forces between either baryonic or nonbaryonic dark matter and ordinary matter.

Effect of shade on animal welfare, growth performance, and carcass characteristics in large pens of beef cattle fed a beta agonist in a commercial feedlot.

PubMed

Hagenmaier, J A; Reinhardt, C D; Bartle, S J; Thomson, D U

2016-12-01

Feedlot cattle ( = 1,395; BW = 568 ± 43 kg) were used to evaluate the effects of shade on animal welfare, growth performance, and carcass quality during the summer of 2013 in a Kansas commercial feedlot. Seven lots of predominately black steers and heifers (4 and 3, respectively) visually determined to be approaching the final mo on feed were identified, randomly gate-sorted, and allocated to pens located across the feed alley from each other to receive 1 of 2 treatments: 1) Shade (mean shade area = 1.5 m/ animal) or 2) No shade. Shade was provided using a 13-ounce polyethylene fabric and pens were oriented northwest to southeast. The mean starting date was June 13 and the mean days on feed for lots while on the study was 38 d. Cattle were fed a 77.67% DM steam-flaked corn-based diet and had ad libitum access to water throughout the duration of the trial. Zilpaterol hydrochloride (ZIL) was included in the finishing ration at an inclusion rate of 8.3 mg/kg of DM for the last 20 d on feed with a 3 d withdrawal period. Pen floor temperatures (PFT) were measured using an infrared thermometer and prevalence of cattle open-mouth breathing (OMB) was recorded on a pen basis. In addition to shade treatment, the effect of temperature humidity index (THI) on PFT and OMB was analyzed by classifying days as either "Alert" (THI < 79) or "Danger" (THI > 79). On the day of slaughter, pens within a replicate were kept separate through all stages of the marketing channel from loading at the feedlot until stunning at the plant. Pen served as the experimental unit for all measurements. There was a THI × shade treatment interaction for PFT and OMB ( < 0.001) where days classified as "Danger" increased PFT and prevalence of OMB compared to "Alert" days in unshaded but not shaded cattle. Shaded cattle had greater DMI ( = 0.01); however, unshaded cattle had greater G:F ( = 0.05) and therefore no differences were observed in ADG ( = 0.39). Shaded cattle had greater dressing percentage ( = 0.01), although HCW, LM area, fat thickness, marbling score, and quality grade did not differ between treatments ( > 0.05). Heat stress, a significant animal welfare concern and cause of reduced performance in feedlot cattle during the final phase of the feeding period, was alleviated in shaded cattle and illustrates the importance of shade provision as 1 tool to protect the welfare and increase feed consumption in large pens of feedlot cattle during hot summer months.

76 FR 70190 - Self-Regulatory Organizations; Financial Industry Regulatory Authority, Inc.; Order Approving...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... concern about dark pools and their potential impact on the fairness and transparency of the national market system.\\12\\ One of these commenters suggested that dark pools be prohibited entirely.\\13\\ FINRA... transparency that currently exists.\\14\\ FINRA stated that all trades executed on an ATS, including a dark pool...

Dinosaur demise in light of their alleged perennial polar residency

NASA Astrophysics Data System (ADS)

Lewy, Zeev

2017-10-01

The end-Cretaceous biological crisis is represented by the demise of the non-avian dinosaurs. However, most crucial biologically was the elimination of the photosynthesizing marine phyto- and zooplankton forming the base of the marine food chain. Their abrupt demise attests to sunlight screening darkening the atmosphere for a few years. Alvarez et al. (Science 208:1095-1108, 1980. doi: 10.1126/science.208.44) noticed in deep marine end-Cretaceous sediments an anomalous rise in the chemical element iridium (Ir), which is rare on planet Earth and thus suggests an extraterrestrial origin through an impact of a large asteroid. This impact would have ejected enormous quantities of particles and aerosols, shading the solar illumination as attested to by the elimination of the marine photosynthesizing plankton. Such a dark period must have affected life on land. The apparent cold-blooded non-avian dinosaurs, which were used to living in open terrains to absorb the solar illumination, became inactive during the dark period and were incapable of withstanding predators. This was in contrast to cold-blooded crocodilians, turtles and lizards that could hide in refuge sites on land and in the water. Dinosaur relics discovered in Cretaceous Polar Regions were attributed to perennial residents, surviving the nearly half-year-long dark winter despite their ability to leave. The polar concentrations of disarticulated dinosaur bones were suggested as having resulted from a catastrophic burial of a population by floods. However, this should have fossilized complete skeletons. Alternatively, herds of dinosaurs living in high latitudes might have been sexually driven to spend the half year of continuously illuminated polar summer for mating rather than for nourishment, in which the lower latitudes provided as well. The aggressive mating competitions would have left victims among the rivals and of young ones incidentally trampled over, all being consumed and their skeletons disarticulated. Accordingly, the alleged `polar dinosaurs' do not challenge the logical conclusion that the non-avian dinosaurs were cold-blooded, as a result of which they became inactive and subjected to predation during the end-Cretaceous dark period.