Signal to noise ratio of energy selective x-ray photon counting systems with pileup

PubMed Central

Alvarez, Robert E.

2014-01-01

Purpose: To derive fundamental limits on the effect of pulse pileup and quantum noise in photon counting detectors on the signal to noise ratio (SNR) and noise variance of energy selective x-ray imaging systems. Methods: An idealized model of the response of counting detectors to pulse pileup is used. The model assumes a nonparalyzable response and delta function pulse shape. The model is used to derive analytical formulas for the noise and energy spectrum of the recorded photons with pulse pileup. These formulas are first verified with a Monte Carlo simulation. They are then used with a method introduced in a previous paper [R. E. Alvarez, “Near optimal energy selective x-ray imaging system performance with simple detectors,” Med. Phys. 37, 822–841 (2010)] to compare the signal to noise ratio with pileup to the ideal SNR with perfect energy resolution. Detectors studied include photon counting detectors with pulse height analysis (PHA), detectors that simultaneously measure the number of photons and the integrated energy (NQ detector), and conventional energy integrating and photon counting detectors. The increase in the A-vector variance with dead time is also computed and compared to the Monte Carlo results. A formula for the covariance of the NQ detector is developed. The validity of the constant covariance approximation to the Cramèr–Rao lower bound (CRLB) for larger counts is tested. Results: The SNR becomes smaller than the conventional energy integrating detector (Q) SNR for 0.52, 0.65, and 0.78 expected number photons per dead time for counting (N), two, and four bin PHA detectors, respectively. The NQ detector SNR is always larger than the N and Q SNR but only marginally so for larger dead times. Its noise variance increases by a factor of approximately 3 and 5 for the A1 and A2 components as the dead time parameter increases from 0 to 0.8 photons per dead time. With four bin PHA data, the increase in variance is approximately 2 and 4 times. The constant covariance approximation to the CRLB is valid for larger counts such as those used in medical imaging. Conclusions: The SNR decreases rapidly as dead time increases. This decrease places stringent limits on allowable dead times with the high count rates required for medical imaging systems. The probability distribution of the idealized data with pileup is shown to be accurately described as a multivariate normal for expected counts greater than those typically utilized in medical imaging systems. The constant covariance approximation to the CRLB is also shown to be valid in this case. A new formula for the covariance of the NQ detector with pileup is derived and validated. PMID:25370642

Statistical Parameter Study of the Time Interval Distribution for Nonparalyzable, Paralyzable, and Hybrid Dead Time Models

NASA Astrophysics Data System (ADS)

Syam, Nur Syamsi; Maeng, Seongjin; Kim, Myo Gwang; Lim, Soo Yeon; Lee, Sang Hoon

2018-05-01

A large dead time of a Geiger Mueller (GM) detector may cause a large count loss in radiation measurements and consequently may cause distortion of the Poisson statistic of radiation events into a new distribution. The new distribution will have different statistical parameters compared to the original distribution. Therefore, the variance, skewness, and excess kurtosis in association with the observed count rate of the time interval distribution for well-known nonparalyzable, paralyzable, and nonparalyzable-paralyzable hybrid dead time models of a Geiger Mueller detector were studied using Monte Carlo simulation (GMSIM). These parameters were then compared with the statistical parameters of a perfect detector to observe the change in the distribution. The results show that the behaviors of the statistical parameters for the three dead time models were different. The values of the skewness and the excess kurtosis of the nonparalyzable model are equal or very close to those of the perfect detector, which are ≅2 for skewness, and ≅6 for excess kurtosis, while the statistical parameters in the paralyzable and hybrid model obtain minimum values that occur around the maximum observed count rates. The different trends of the three models resulting from the GMSIM simulation can be used to distinguish the dead time behavior of a GM counter; i.e. whether the GM counter can be described best by using the nonparalyzable, paralyzable, or hybrid model. In a future study, these statistical parameters need to be analyzed further to determine the possibility of using them to determine a dead time for each model, particularly for paralyzable and hybrid models.

SU-E-I-88: The Effect of System Dead Time On Real-Time Plastic and GOS Based Fiber-Optic Dosimetry Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoerner, M; Hintenlang, D

Purpose: A methodology is presented to correct for measurement inaccuracies at high detector count rates using a plastic and GOS scintillation fibers coupled to a photomultiplier tube with digital readout. This system allows temporal acquisition and manipulation of measured data. Methods: The detection system used was a plastic scintillator and a separate gadolinium scintillator, both (0.5 diameter) coupled to an optical fiber with a Hamamatsu photon counter with a built-in microcontroller and digital interface. Count rate performance of the system was evaluated using the nonparalzable detector model. Detector response was investigated across multiple radiation sources including: orthovoltage x-ray system, colbat-60more » gamma rays, proton therapy beam, and a diagnostic radiography x-ray tube. The dead time parameter was calculated by measuring the count rate of the system at different exposure rates using a reference detector. Results: The system dead time was evaluated for the following sources of radiation used clinically: diagnostic energy x-rays, cobalt-60 gamma rays, orthovoltage xrays, particle proton accelerator, and megavoltage x-rays. It was found that dead time increased significantly when exposing the detector to sources capable of generating Cerenkov radiation, all of the sources sans the diagnostic x-rays, with increasing prominence at higher photon energies. Percent depth dose curves generated by a dedicated ionization chamber and compared to the detection system demonstrated that correcting for dead time improves accuracy. On most sources, nonparalzable model fit provided an improved system response. Conclusion: Overall, the system dead time was variable across the investigated radiation particles and energies. It was demonstrated that the system response accuracy was greatly improved by correcting for dead time effects. Cerenkov radiation plays a significant role in the increase in the system dead time through transient absorption effects attributed to electron hole-pair creations within the optical waveguide.« less

Avalanche photodiode photon counting receivers for space-borne lidars

NASA Technical Reports Server (NTRS)

Sun, Xiaoli; Davidson, Frederic M.

1991-01-01

Avalanche photodiodes (APD) are studied for uses as photon counting detectors in spaceborne lidars. Non-breakdown APD photon counters, in which the APD's are biased below the breakdown point, are shown to outperform: (1) conventional APD photon counters biased above the breakdown point; (2) conventional APD photon counters biased above the breakdown point; and (3) APD's in analog mode when the received optical signal is extremely weak. Non-breakdown APD photon counters were shown experimentally to achieve an effective photon counting quantum efficiency of 5.0 percent at lambda = 820 nm with a dead time of 15 ns and a dark count rate of 7000/s which agreed with the theoretically predicted values. The interarrival times of the counts followed an exponential distribution and the counting statistics appeared to follow a Poisson distribution with no after pulsing. It is predicted that the effective photon counting quantum efficiency can be improved to 18.7 percent at lambda = 820 nm and 1.46 percent at lambda = 1060 nm with a dead time of a few nanoseconds by using more advanced commercially available electronic components.

A high dynamic range pulse counting detection system for mass spectrometry.

PubMed

Collings, Bruce A; Dima, Martian D; Ivosev, Gordana; Zhong, Feng

2014-01-30

A high dynamic range pulse counting system has been developed that demonstrates an ability to operate at up to 2e8 counts per second (cps) on a triple quadrupole mass spectrometer. Previous pulse counting detection systems have typically been limited to about 1e7 cps at the upper end of the systems dynamic range. Modifications to the detection electronics and dead time correction algorithm are described in this paper. A high gain transimpedance amplifier is employed that allows a multi-channel electron multiplier to be operated at a significantly lower bias potential than in previous pulse counting systems. The system utilises a high-energy conversion dynode, a multi-channel electron multiplier, a high gain transimpedance amplifier, non-paralysing detection electronics and a modified dead time correction algorithm. Modification of the dead time correction algorithm is necessary due to a characteristic of the pulse counting electronics. A pulse counting detection system with the capability to count at ion arrival rates of up to 2e8 cps is described. This is shown to provide a linear dynamic range of nearly five orders of magnitude for a sample of aprazolam with concentrations ranging from 0.0006970 ng/mL to 3333 ng/mL while monitoring the m/z 309.1 → m/z 205.2 transition. This represents an upward extension of the detector's linear dynamic range of about two orders of magnitude. A new high dynamic range pulse counting system has been developed demonstrating the ability to operate at up to 2e8 cps on a triple quadrupole mass spectrometer. This provides an upward extension of the detector's linear dynamic range by about two orders of magnitude over previous pulse counting systems. Copyright © 2013 John Wiley & Sons, Ltd.

Counting-loss correction for X-ray spectroscopy using unit impulse pulse shaping.

PubMed

Hong, Xu; Zhou, Jianbin; Ni, Shijun; Ma, Yingjie; Yao, Jianfeng; Zhou, Wei; Liu, Yi; Wang, Min

2018-03-01

High-precision measurement of X-ray spectra is affected by the statistical fluctuation of the X-ray beam under low-counting-rate conditions. It is also limited by counting loss resulting from the dead-time of the system and pile-up pulse effects, especially in a high-counting-rate environment. In this paper a detection system based on a FAST-SDD detector and a new kind of unit impulse pulse-shaping method is presented, for counting-loss correction in X-ray spectroscopy. The unit impulse pulse-shaping method is evolved by inverse deviation of the pulse from a reset-type preamplifier and a C-R shaper. It is applied to obtain the true incoming rate of the system based on a general fast-slow channel processing model. The pulses in the fast channel are shaped to unit impulse pulse shape which possesses small width and no undershoot. The counting rate in the fast channel is corrected by evaluating the dead-time of the fast channel before it is used to correct the counting loss in the slow channel.

Digital instrumentation and management of dead time: first results on a NaI well-type detector setup.

PubMed

Censier, B; Bobin, C; Bouchard, J; Aubineau-Lanièce, I

2010-01-01

The LNE-LNHB is engaged in a development program on digital instrumentation, the first step being the instrumentation of a NaI well-type detector set-up. The prototype acquisition card and its technical specifications are presented together with the first comparison with the classical NIM-based acquisition chain, for counting rates up to 100 kcps. The digital instrumentation is shown to be counting-loss free in this range. This validates the main option adopted in this project, namely the implementation of an extending dead time with live-time measurement already successfully used in the MTR2 NIM module developed at LNE-LNHB. Copyright 2010. Published by Elsevier Ltd.

Extension of the Dytlewski-style dead time correction formalism for neutron multiplicity counting to any order

NASA Astrophysics Data System (ADS)

Croft, Stephen; Favalli, Andrea

2017-10-01

Neutron multiplicity counting using shift-register calculus is an established technique in the science of international nuclear safeguards for the identification, verification, and assay of special nuclear materials. Typically passive counting is used for Pu and mixed Pu-U items and active methods are used for U materials. Three measured counting rates, singles, doubles and triples are measured and, in combination with a simple analytical point-model, are used to calculate characteristics of the measurement item in terms of known detector and nuclear parameters. However, the measurement problem usually involves more than three quantities of interest, but even in cases where the next higher order count rate, quads, is statistically viable, it is not quantitatively applied because corrections for dead time losses are currently not available in the predominant analysis paradigm. In this work we overcome this limitation by extending the commonly used dead time correction method, developed by Dytlewski, to quads. We also give results for pents, which may be of interest for certain special investigations. Extension to still higher orders, may be accomplished by inspection based on the sequence presented. We discuss the foundations of the Dytlewski method, give limiting cases, and highlight the opportunities and implications that these new results expose. In particular there exist a number of ways in which the new results may be combined with other approaches to extract the correlated rates, and this leads to various practical implementations.

Extension of the Dytlewski-style dead time correction formalism for neutron multiplicity counting to any order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Croft, Stephen; Favalli, Andrea

Here, neutron multiplicity counting using shift-register calculus is an established technique in the science of international nuclear safeguards for the identification, verification, and assay of special nuclear materials. Typically passive counting is used for Pu and mixed Pu-U items and active methods are used for U materials. Three measured counting rates, singles, doubles and triples are measured and, in combination with a simple analytical point-model, are used to calculate characteristics of the measurement item in terms of known detector and nuclear parameters. However, the measurement problem usually involves more than three quantities of interest, but even in cases where themore » next higher order count rate, quads, is statistically viable, it is not quantitatively applied because corrections for dead time losses are currently not available in the predominant analysis paradigm. In this work we overcome this limitation by extending the commonly used dead time correction method, developed by Dytlewski, to quads. We also give results for pents, which may be of interest for certain special investigations. Extension to still higher orders, may be accomplished by inspection based on the sequence presented. We discuss the foundations of the Dytlewski method, give limiting cases, and highlight the opportunities and implications that these new results expose. In particular there exist a number of ways in which the new results may be combined with other approaches to extract the correlated rates, and this leads to various practical implementations.« less

Extension of the Dytlewski-style dead time correction formalism for neutron multiplicity counting to any order

DOE PAGES

Croft, Stephen; Favalli, Andrea

2017-07-16

Here, neutron multiplicity counting using shift-register calculus is an established technique in the science of international nuclear safeguards for the identification, verification, and assay of special nuclear materials. Typically passive counting is used for Pu and mixed Pu-U items and active methods are used for U materials. Three measured counting rates, singles, doubles and triples are measured and, in combination with a simple analytical point-model, are used to calculate characteristics of the measurement item in terms of known detector and nuclear parameters. However, the measurement problem usually involves more than three quantities of interest, but even in cases where themore » next higher order count rate, quads, is statistically viable, it is not quantitatively applied because corrections for dead time losses are currently not available in the predominant analysis paradigm. In this work we overcome this limitation by extending the commonly used dead time correction method, developed by Dytlewski, to quads. We also give results for pents, which may be of interest for certain special investigations. Extension to still higher orders, may be accomplished by inspection based on the sequence presented. We discuss the foundations of the Dytlewski method, give limiting cases, and highlight the opportunities and implications that these new results expose. In particular there exist a number of ways in which the new results may be combined with other approaches to extract the correlated rates, and this leads to various practical implementations.« less

The relationship between tree growth patterns and likelihood of mortality: A study of two tree species in the Sierra Nevada

USGS Publications Warehouse

Das, A.J.; Battles, J.J.; Stephenson, N.L.; van Mantgem, P.J.

2007-01-01

We examined mortality of Abies concolor (Gord. & Glend.) Lindl. (white fir) and Pinus lambertiana Dougl. (sugar pine) by developing logistic models using three growth indices obtained from tree rings: average growth, growth trend, and count of abrupt growth declines. For P. lambertiana, models with average growth, growth trend, and count of abrupt declines improved overall prediction (78.6% dead trees correctly classified, 83.7% live trees correctly classified) compared with a model with average recent growth alone (69.6% dead trees correctly classified, 67.3% live trees correctly classified). For A. concolor, counts of abrupt declines and longer time intervals improved overall classification (trees with DBH ???20 cm: 78.9% dead trees correctly classified and 76.7% live trees correctly classified vs. 64.9% dead trees correctly classified and 77.9% live trees correctly classified; trees with DBH <20 cm: 71.6% dead trees correctly classified and 71.0% live trees correctly classified vs. 67.2% dead trees correctly classified and 66.7% live trees correctly classified). In general, count of abrupt declines improved live-tree classification. External validation of A. concolor models showed that they functioned well at stands not used in model development, and the development of size-specific models demonstrated important differences in mortality risk between understory and canopy trees. Population-level mortality-risk models were developed for A. concolor and generated realistic mortality rates at two sites. Our results support the contention that a more comprehensive use of the growth record yields a more robust assessment of mortality risk. ?? 2007 NRC.

Designing primers and evaluation of the efficiency of propidium monoazide - Quantitative polymerase chain reaction for counting the viable cells of Lactobacillus gasseri and Lactobacillus salivarius.

PubMed

Lai, Chieh-Hsien; Wu, Sih-Rong; Pang, Jen-Chieh; Ramireddy, Latha; Chiang, Yu-Cheng; Lin, Chien-Ku; Tsen, Hau-Yang

2017-07-01

The purpose of this study is to evaluate the efficiency of using propidium monoazide (PMA) real-time quantitative polymerase chain reaction (qPCR) to count the viable cells of Lactobacillus gasseri and Lactobacillus salivarius in probiotic products. Based on the internal transcription spacer and 23S rRNA genes, two primer sets specific for these two Lactobacillus species were designed. For a probiotic product, the total deMan Rogosa Sharpe plate count was 8.65±0.69 log CFU/g, while for qPCR, the cell counts of L. gasseri and L. salivarius were 8.39±0.14 log CFU/g and 8.57±0.24 log CFU/g, respectively. Under the same conditions, for its heat-killed product, qPCR counts for L. gasseri and L. salivarius were 6.70±0.16 log cells/g and 7.67±0.20 log cells/g, while PMA-qPCR counts were 5.33±0.18 log cells/g and 5.05±0.23 log cells/g, respectively. For cell dilutions with a viable cell count of 8.5 log CFU/mL for L. gasseri and L. salivarius, after heat killing, the PMA-qPCR count for both Lactobacillus species was near 5.5 log cells/mL. When the PMA-qPCR counts of these cell dilutions were compared before and after heat killing, although some DNA might be lost during the heat killing, significant qPCR signals from dead cells, i.e., about 4-5 log cells/mL, could not be reduced by PMA treatment. Increasing PMA concentrations from 100 μM to 200 μM or light exposure time from 5 minutes to 15 minutes had no or, if any, only minor effect on the reduction of qPCR signals from their dead cells. Thus, to differentiate viable lactic acid bacterial cells from dead cells using the PMA-qPCR method, the efficiency of PMA to reduce the qPCR signals from dead cells should be notable. Copyright © 2016. Published by Elsevier B.V.

Note: Fully integrated active quenching circuit achieving 100 MHz count rate with custom technology single photon avalanche diodes.

PubMed

Acconcia, G; Labanca, I; Rech, I; Gulinatti, A; Ghioni, M

2017-02-01

The minimization of Single Photon Avalanche Diodes (SPADs) dead time is a key factor to speed up photon counting and timing measurements. We present a fully integrated Active Quenching Circuit (AQC) able to provide a count rate as high as 100 MHz with custom technology SPAD detectors. The AQC can also operate the new red enhanced SPAD and provide the timing information with a timing jitter Full Width at Half Maximum (FWHM) as low as 160 ps.

Risk assessment of false-positive quantitative real-time PCR results in food, due to detection of DNA originating from dead cells.

PubMed

Wolffs, Petra; Norling, Börje; Rådström, Peter

2005-03-01

Real-time PCR technology is increasingly used for detection and quantification of pathogens in food samples. A main disadvantage of nucleic acid detection is the inability to distinguish between signals originating from viable cells and DNA released from dead cells. In order to gain knowledge concerning risks of false-positive results due to detection of DNA originating from dead cells, quantitative PCR (qPCR) was used to investigate the degradation kinetics of free DNA in four types of meat samples. Results showed that the fastest degradation rate was observed (1 log unit per 0.5 h) in chicken homogenate, whereas the slowest rate was observed in pork rinse (1 log unit per 120.5 h). Overall results indicated that degradation occurred faster in chicken samples than in pork samples and faster at higher temperatures. Based on these results, it was concluded that, especially in pork samples, there is a risk of false-positive PCR results. This was confirmed in a quantitative study on cell death and signal persistence over a period of 28 days, employing three different methods, i.e. viable counts, direct qPCR, and finally floatation, a recently developed discontinuous density centrifugation method, followed by qPCR. Results showed that direct qPCR resulted in an overestimation of up to 10 times of the amount of cells in the samples compared to viable counts, due to detection of DNA from dead cells. However, after using floatation prior to qPCR, results resembled the viable count data. This indicates that by using of floatation as a sample treatment step prior to qPCR, the risk of false-positive PCR results due to detection of dead cells, can be minimized.

Discrimination of shot-noise-driven Poisson processes by external dead time - Application of radioluminescence from glass

NASA Technical Reports Server (NTRS)

Saleh, B. E. A.; Tavolacci, J. T.; Teich, M. C.

1981-01-01

Ways in which dead time can be used to constructively enhance or diminish the effects of point processes that display bunching in the shot-noise-driven doubly stochastic Poisson point process (SNDP) are discussed. Interrelations between photocount bunching arising in the SNDP and the antibunching character arising from dead-time effects are investigated. It is demonstrated that the dead-time-modified count mean and variance for an arbitrary doubly stochastic Poisson point process can be obtained from the Laplace transform of the single-fold and joint-moment-generating functions for the driving rate process. The theory is in good agreement with experimental values for radioluminescence radiation in fused silica, quartz, and glass, and the process has many applications in pulse, particle, and photon detection.

The Feynman-Y Statistic in Relation to Shift-Register Neutron Coincidence Counting: Precision and Dead Time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Croft, Stephen; Santi, Peter A.; Henzlova, Daniela

The Feynman-Y statistic is a type of autocorrelation analysis. It is defined as the excess variance-to-mean ratio, Y = VMR - 1, of the number count distribution formed by sampling a pulse train using a series of non-overlapping gates. It is a measure of the degree of correlation present on the pulse train with Y = 0 for Poisson data. In the context of neutron coincidence counting we show that the same information can be obtained from the accidentals histogram acquired using the multiplicity shift-register method, which is currently the common autocorrelation technique applied in nuclear safeguards. In the casemore » of multiplicity shift register analysis however, overlapping gates, either triggered by the incoming pulse stream or by a periodic clock, are used. The overlap introduces additional covariance but does not alter the expectation values. In this paper we discuss, for a particular data set, the relative merit of the Feynman and shift-register methods in terms of both precision and dead time correction. Traditionally the Feynman approach is applied with a relatively long gate width compared to the dieaway time. The main reason for this is so that the gate utilization factor can be taken as unity rather than being treated as a system parameter to be determined at characterization/calibration. But because the random trigger interval gate utilization factor is slow to saturate this procedure requires a gate width many times the effective 1/e dieaway time. In the traditional approach this limits the number of gates that can be fitted into a given assay duration. We empirically show that much shorter gates, similar in width to those used in traditional shift register analysis can be used. Because the way in which the correlated information present on the pulse train is extracted is different for the moments based method of Feynman and the various shift register based approaches, the dead time losses are manifested differently for these two approaches. The resulting estimates for the dead time corrected first and second order reduced factorial moments should be independent of the method however and this allows the respective dead time formalism to be checked. We discuss how to make dead time corrections in both the shift register and the Feynman approaches.« less

Live/Dead Bacterial Spore Assay Using DPA-Triggered Tb Luminescence

NASA Technical Reports Server (NTRS)

Ponce, Adrian

2003-01-01

A method of measuring the fraction of bacterial spores in a sample that remain viable exploits DPA-triggered luminescence of Tb(3+) and is based partly on the same principles as those described earlier. Unlike prior methods for performing such live/dead assays of bacterial spores, this method does not involve counting colonies formed by cultivation (which can take days), or counting of spores under a microscope, and works whether or not bacterial spores are attached to other small particles (i.e., dust), and can be implemented on a time scale of about 20 minutes.

NO TIME FOR DEAD TIME: TIMING ANALYSIS OF BRIGHT BLACK HOLE BINARIES WITH NuSTAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bachetti, Matteo; Barret, Didier; Harrison, Fiona A.

Timing of high-count-rate sources with the NuSTAR Small Explorer Mission requires specialized analysis techniques. NuSTAR was primarily designed for spectroscopic observations of sources with relatively low count rates rather than for timing analysis of bright objects. The instrumental dead time per event is relatively long (∼2.5 msec) and varies event-to-event by a few percent. The most obvious effect is a distortion of the white noise level in the power density spectrum (PDS) that cannot be easily modeled with standard techniques due to the variable nature of the dead time. In this paper, we show that it is possible to exploitmore » the presence of two completely independent focal planes and use the cospectrum, the real part of the cross PDS, to obtain a good proxy of the white-noise-subtracted PDS. Thereafter, one can use a Monte Carlo approach to estimate the remaining effects of dead time, namely, a frequency-dependent modulation of the variance and a frequency-independent drop of the sensitivity to variability. In this way, most of the standard timing analysis can be performed, albeit with a sacrifice in signal-to-noise ratio relative to what would be achieved using more standard techniques. We apply this technique to NuSTAR observations of the black hole binaries GX 339–4, Cyg X-1, and GRS 1915+105.« less

A bismuth activation counter for high sensitivity pulsed 14 MeV neutrons

NASA Astrophysics Data System (ADS)

Burns, E. J. T.; Thacher, P. D.; Hassig, G. J.; Decker, R. D.; Romero, J. A.; Barrett, K. P.

2011-08-01

We have built a fast neutron bismuth activation counter that measures activation counts from pulsed 14-MeV neutron generators for incident neutron fluences between 30 and 300 neutrons/cm2 at 15.2 cm (6 in.). The activation counter consists of a large bismuth germanate (BGO) detector surrounded by a bismuth metal shield in front of and concentric with the cylindrical detector housing. The 14 MeV neutrons activate the 2.6-millisecond (ms) isomer in the shield and the detector by the reaction 209Bi (n,2nγ) 208mBi. The use of millisecond isomers and activation counting times minimizes the background from other activated materials and the environment. In addition to activation, the bismuth metal shields against other outside radiation sources. We have tested the bismuth activation counter, simultaneously, with two data acquisition systems (DASs) and both give similar results. The two-dimensional (2D) DAS and three dimensional (3D) DAS both consist of pulse height analysis (PHA) systems that can be used to discriminate against gamma radiations below 300 keV photon energy, so that the detector can be used strictly as a counter. If the counting time is restricted to less than 25 ms after the neutron pulse, there are less than 10 counts of background for single pulse operation in all our operational environments tested so far. High-fluence neutron generator operations are restricted by large dead times and pulse height saturation. When we operate our 3D DAS PHA system in list mode acquisition (LIST), real-time corrections to dead time or live time can be made on the scale of 1 ms time windows or dwell times. The live time correction is consistent with nonparalyzable models for dead time of 1.0±0.2 μs for our 3D DAS and 1.5±0.3 μs for our 2D DAS dominated by our fixed time width analog to digital converters (ADCs). With the same solid angle, we have shown that the bismuth activation counter has a factor of 4 increase in sensitivity over our lead activation counter, because of higher counts and negligible backgrounds.

A general dead-time correction method based on live-time stamping. Application to the measurement of short-lived radionuclides.

PubMed

Chauvenet, B; Bobin, C; Bouchard, J

2017-12-01

Dead-time correction formulae are established in the general case of superimposed non-homogeneous Poisson processes. Based on the same principles as conventional live-timed counting, this method exploits the additional information made available using digital signal processing systems, and especially the possibility to store the time stamps of live-time intervals. No approximation needs to be made to obtain those formulae. Estimates of the variances of corrected rates are also presented. This method is applied to the activity measurement of short-lived radionuclides. Copyright © 2017 Elsevier Ltd. All rights reserved.

Gigahertz-gated InGaAs/InP single-photon detector with detection efficiency exceeding 55% at 1550 nm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comandar, L. C.; Engineering Department, Cambridge University, 9 J J Thomson Ave, Cambridge CB3 0FA; Fröhlich, B.

We report on a gated single-photon detector based on InGaAs/InP avalanche photodiodes (APDs) with a single-photon detection efficiency exceeding 55% at 1550 nm. Our detector is gated at 1 GHz and employs the self-differencing technique for gate transient suppression. It can operate nearly dead time free, except for the one clock cycle dead time intrinsic to self-differencing, and we demonstrate a count rate of 500 Mcps. We present a careful analysis of the optimal driving conditions of the APD measured with a dead time free detector characterization setup. It is found that a shortened gate width of 360 ps together with anmore » increased driving signal amplitude and operation at higher temperatures leads to improved performance of the detector. We achieve an afterpulse probability of 7% at 50% detection efficiency with dead time free measurement and a record efficiency for InGaAs/InP APDs of 55% at an afterpulse probability of only 10.2% with a moderate dead time of 10 ns.« less

Electronic strain-level counter

NASA Technical Reports Server (NTRS)

Pitts, F. L.; Spencer, J. L. (Inventor)

1973-01-01

An electronic strain level counter for obtaining structural strain data on in-flight aircraft is described. The device counts the number of times the strain at a point on an aircraft structural member exceeds each of several preset levels. A dead band is provided at each level to prohibit the counting of small strain variations around a given preset level.

A study of pile-up in integrated time-correlated single photon counting systems

NASA Astrophysics Data System (ADS)

Arlt, Jochen; Tyndall, David; Rae, Bruce R.; Li, David D.-U.; Richardson, Justin A.; Henderson, Robert K.

2013-10-01

Recent demonstration of highly integrated, solid-state, time-correlated single photon counting (TCSPC) systems in CMOS technology is set to provide significant increases in performance over existing bulky, expensive hardware. Arrays of single photon single photon avalanche diode (SPAD) detectors, timing channels, and signal processing can be integrated on a single silicon chip with a degree of parallelism and computational speed that is unattainable by discrete photomultiplier tube and photon counting card solutions. New multi-channel, multi-detector TCSPC sensor architectures with greatly enhanced throughput due to minimal detector transit (dead) time or timing channel dead time are now feasible. In this paper, we study the potential for future integrated, solid-state TCSPC sensors to exceed the photon pile-up limit through analytic formula and simulation. The results are validated using a 10% fill factor SPAD array and an 8-channel, 52 ps resolution time-to-digital conversion architecture with embedded lifetime estimation. It is demonstrated that pile-up insensitive acquisition is attainable at greater than 10 times the pulse repetition rate providing over 60 dB of extended dynamic range to the TCSPC technique. Our results predict future CMOS TCSPC sensors capable of live-cell transient observations in confocal scanning microscopy, improved resolution of near-infrared optical tomography systems, and fluorescence lifetime activated cell sorting.

A study of pile-up in integrated time-correlated single photon counting systems.

PubMed

Arlt, Jochen; Tyndall, David; Rae, Bruce R; Li, David D-U; Richardson, Justin A; Henderson, Robert K

2013-10-01

Recent demonstration of highly integrated, solid-state, time-correlated single photon counting (TCSPC) systems in CMOS technology is set to provide significant increases in performance over existing bulky, expensive hardware. Arrays of single photon single photon avalanche diode (SPAD) detectors, timing channels, and signal processing can be integrated on a single silicon chip with a degree of parallelism and computational speed that is unattainable by discrete photomultiplier tube and photon counting card solutions. New multi-channel, multi-detector TCSPC sensor architectures with greatly enhanced throughput due to minimal detector transit (dead) time or timing channel dead time are now feasible. In this paper, we study the potential for future integrated, solid-state TCSPC sensors to exceed the photon pile-up limit through analytic formula and simulation. The results are validated using a 10% fill factor SPAD array and an 8-channel, 52 ps resolution time-to-digital conversion architecture with embedded lifetime estimation. It is demonstrated that pile-up insensitive acquisition is attainable at greater than 10 times the pulse repetition rate providing over 60 dB of extended dynamic range to the TCSPC technique. Our results predict future CMOS TCSPC sensors capable of live-cell transient observations in confocal scanning microscopy, improved resolution of near-infrared optical tomography systems, and fluorescence lifetime activated cell sorting.

Evaluation of dead-time corrections for post-radionuclide-therapy (177)Lu quantitative imaging with low-energy high-resolution collimators.

PubMed

Celler, Anna; Piwowarska-Bilska, Hanna; Shcherbinin, Sergey; Uribe, Carlos; Mikolajczak, Renata; Birkenfeld, Bozena

2014-01-01

Dead-time (DT) effects rarely cause problems in diagnostic single-photon emission computed tomography (SPECT) studies; however, in post-radionuclide-therapy imaging, DT can be substantial. Therefore, corrections may be necessary if quantitative images are used in image-based dosimetry or for evaluation of therapy outcomes. This task is particularly challenging if low-energy collimators are used. Our goal was to design a simple method to determine the dead-time correction factor (DTCF) without the need for phantom experiments and complex calculations. Planar and SPECT/CT scans of a water phantom containing a 70 ml bottle filled with lutetium-177 (Lu) were acquired over 60 days. Two small Lu markers were used in all scans. The DTCF based on the ratio of observed to true count rates measured over the entire spectrum and using photopeak primary photons only was estimated for phantom (DT present) and marker (no DT) scans. In addition, variations in counts in SPECT projections (potentially caused by varying bremsstrahlung and scatter) were investigated. For count rates that were about two-fold higher than typically seen in post-therapy Lu scans, the maximum DTCF reached a level of about 17%. The DTCF values determined directly from the phantom experiments using the total energy spectrum and photopeak counts only were equal to 13 and 16%, respectively. They were closely matched by those from the proposed marker-based method, which uses only two energy windows and measures photopeak primary photons (15-17%). A simple, marker-based method allowing for determination of the DTCF in high-activity Lu imaging studies has been proposed and validated using phantom experiments.

NEMA count-rate evaluation of the first and second generation of the Ecat Exact and Ecat Exact HR family of scanners

NASA Astrophysics Data System (ADS)

Eriksson, L.; Wienhard, K.; Eriksson, M.; Casey, M. E.; Knoess, C.; Bruckbauer, T.; Hamill, J.; Mulnix, T.; Vollmar, S.; Bendriem, B.; Heiss, W. D.; Nutt, R.

2002-06-01

The first and second generation of the Exact and Exact HR family of scanners has been evaluated in terms of noise equivalent count rate (NEC) and count-rate capabilities. The new National Electrical Manufacturers Association standard was used for the evaluation. In spite of improved electronics and improved count-rate capabilities, the peak NEC was found to be fairly constant between the generations. The results are discussed in terms of the different electronic solutions for the two generations and its implications on system dead time and NEC count-rate capability.

Six orders of magnitude dynamic range in capillary electrophoresis with ultrasensitive laser-induced fluorescence detection

PubMed Central

Whitmore, Colin D.; Essaka, David; Dovichi, Norman J.

2009-01-01

An ultrasensitive laser-induced fluorescence detector was used with capillary electrophoresis for the study of 5-carboxy-tetramethylrhodamine. The raw signal from the detector provided roughly three orders of magnitude dynamic range. The signal saturated at high analyte concentrations due to the dead time associated with the single-photon counting avalanche photodiode employed in the detector. The signal can be corrected for the detector dead time, providing an additional order of magnitude dynamic range. To further increase dynamic range, two fiber-optic beam-splitters were cascaded to generate a primary signal and two attenuated signals, each monitored by a single-photon counting avalanche photodiode. The combined signals from the three photodiodes are reasonably linear from the concentration detection limit of 3 pM to 10 μM, the maximum concentration investigated, a range of 3,000,000. Mass detection limits were 150 yoctomoles injected onto the capillary. PMID:19836546

Implementation and Initial Testing of Advanced Processing and Analysis Algorithms for Correlated Neutron Counting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santi, Peter Angelo; Cutler, Theresa Elizabeth; Favalli, Andrea

In order to improve the accuracy and capabilities of neutron multiplicity counting, additional quantifiable information is needed in order to address the assumptions that are present in the point model. Extracting and utilizing higher order moments (Quads and Pents) from the neutron pulse train represents the most direct way of extracting additional information from the measurement data to allow for an improved determination of the physical properties of the item of interest. The extraction of higher order moments from a neutron pulse train required the development of advanced dead time correction algorithms which could correct for dead time effects inmore » all of the measurement moments in a self-consistent manner. In addition, advanced analysis algorithms have been developed to address specific assumptions that are made within the current analysis model, namely that all neutrons are created at a single point within the item of interest, and that all neutrons that are produced within an item are created with the same energy distribution. This report will discuss the current status of implementation and initial testing of the advanced dead time correction and analysis algorithms that have been developed in an attempt to utilize higher order moments to improve the capabilities of correlated neutron measurement techniques.« less

Monte Carlo simulation of the neutron monitor yield function

NASA Astrophysics Data System (ADS)

Mangeard, P.-S.; Ruffolo, D.; Sáiz, A.; Madlee, S.; Nutaro, T.

2016-08-01

Neutron monitors (NMs) are ground-based detectors that measure variations of the Galactic cosmic ray flux at GV range rigidities. Differences in configuration, electronics, surroundings, and location induce systematic effects on the calculation of the yield functions of NMs worldwide. Different estimates of NM yield functions can differ by a factor of 2 or more. In this work, we present new Monte Carlo simulations to calculate NM yield functions and perform an absolute (not relative) comparison with the count rate of the Princess Sirindhorn Neutron Monitor (PSNM) at Doi Inthanon, Thailand, both for the entire monitor and for individual counter tubes. We model the atmosphere using profiles from the Global Data Assimilation System database and the Naval Research Laboratory Mass Spectrometer, Incoherent Scatter Radar Extended model. Using FLUKA software and the detailed geometry of PSNM, we calculated the PSNM yield functions for protons and alpha particles. An agreement better than 9% was achieved between the PSNM observations and the simulated count rate during the solar minimum of December 2009. The systematic effect from the electronic dead time was studied as a function of primary cosmic ray rigidity at the top of the atmosphere up to 1 TV. We show that the effect is not negligible and can reach 35% at high rigidity for a dead time >1 ms. We analyzed the response function of each counter tube at PSNM using its actual dead time, and we provide normalization coefficients between count rates for various tube configurations in the standard NM64 design that are valid to within ˜1% for such stations worldwide.

Submillisecond X-ray photon correlation spectroscopy from a pixel array detector with fast dual gating and no readout dead-time

DOE PAGES

Zhang, Qingteng; Dufresne, Eric M.; Grybos, Pawel; ...

2016-04-19

Small-angle scattering X-ray photon correlation spectroscopy (XPCS) studies were performed using a novel photon-counting pixel array detector with dual counters for each pixel. Each counter can be read out independently from the other to ensure there is no readout dead-time between the neighboring frames. A maximum frame rate of 11.8 kHz was achieved. Results on test samples show good agreement with simple diffusion. Lastly, the potential of extending the time resolution of XPCS beyond the limit set by the detector frame rate using dual counters is also discussed.

Submillisecond X-ray photon correlation spectroscopy from a pixel array detector with fast dual gating and no readout dead-time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Qingteng; Dufresne, Eric M.; Grybos, Pawel

Small-angle scattering X-ray photon correlation spectroscopy (XPCS) studies were performed using a novel photon-counting pixel array detector with dual counters for each pixel. Each counter can be read out independently from the other to ensure there is no readout dead-time between the neighboring frames. A maximum frame rate of 11.8 kHz was achieved. Results on test samples show good agreement with simple diffusion. Lastly, the potential of extending the time resolution of XPCS beyond the limit set by the detector frame rate using dual counters is also discussed.

Submillisecond X-ray photon correlation spectroscopy from a pixel array detector with fast dual gating and no readout dead-time.

PubMed

Zhang, Qingteng; Dufresne, Eric M; Grybos, Pawel; Kmon, Piotr; Maj, Piotr; Narayanan, Suresh; Deptuch, Grzegorz W; Szczygiel, Robert; Sandy, Alec

2016-05-01

Small-angle scattering X-ray photon correlation spectroscopy (XPCS) studies were performed using a novel photon-counting pixel array detector with dual counters for each pixel. Each counter can be read out independently from the other to ensure there is no readout dead-time between the neighboring frames. A maximum frame rate of 11.8 kHz was achieved. Results on test samples show good agreement with simple diffusion. The potential of extending the time resolution of XPCS beyond the limit set by the detector frame rate using dual counters is also discussed.

Dead-time optimized time-correlated photon counting instrument with synchronized, independent timing channels

NASA Astrophysics Data System (ADS)

Wahl, Michael; Rahn, Hans-Jürgen; Gregor, Ingo; Erdmann, Rainer; Enderlein, Jörg

2007-03-01

Time-correlated single photon counting is a powerful method for sensitive time-resolved fluorescence measurements down to the single molecule level. The method is based on the precisely timed registration of single photons of a fluorescence signal. Historically, its primary goal was the determination of fluorescence lifetimes upon optical excitation by a short light pulse. This goal is still important today and therefore has a strong influence on instrument design. However, modifications and extensions of the early designs allow for the recovery of much more information from the detected photons and enable entirely new applications. Here, we present a new instrument that captures single photon events on multiple synchronized channels with picosecond resolution and over virtually unlimited time spans. This is achieved by means of crystal-locked time digitizers with high resolution and very short dead time. Subsequent event processing in programmable logic permits classical histogramming as well as time tagging of individual photons and their streaming to the host computer. Through the latter, any algorithms and methods for the analysis of fluorescence dynamics can be implemented either in real time or offline. Instrument test results from single molecule applications will be presented.

Characterization of 3-Dimensional PET Systems for Accurate Quantification of Myocardial Blood Flow.

PubMed

Renaud, Jennifer M; Yip, Kathy; Guimond, Jean; Trottier, Mikaël; Pibarot, Philippe; Turcotte, Eric; Maguire, Conor; Lalonde, Lucille; Gulenchyn, Karen; Farncombe, Troy; Wisenberg, Gerald; Moody, Jonathan; Lee, Benjamin; Port, Steven C; Turkington, Timothy G; Beanlands, Rob S; deKemp, Robert A

2017-01-01

Three-dimensional (3D) mode imaging is the current standard for PET/CT systems. Dynamic imaging for quantification of myocardial blood flow with short-lived tracers, such as 82 Rb-chloride, requires accuracy to be maintained over a wide range of isotope activities and scanner counting rates. We proposed new performance standard measurements to characterize the dynamic range of PET systems for accurate quantitative imaging. 82 Rb or 13 N-ammonia (1,100-3,000 MBq) was injected into the heart wall insert of an anthropomorphic torso phantom. A decaying isotope scan was obtained over 5 half-lives on 9 different 3D PET/CT systems and 1 3D/2-dimensional PET-only system. Dynamic images (28 × 15 s) were reconstructed using iterative algorithms with all corrections enabled. Dynamic range was defined as the maximum activity in the myocardial wall with less than 10% bias, from which corresponding dead-time, counting rates, and/or injected activity limits were established for each scanner. Scatter correction residual bias was estimated as the maximum cavity blood-to-myocardium activity ratio. Image quality was assessed via the coefficient of variation measuring nonuniformity of the left ventricular myocardium activity distribution. Maximum recommended injected activity/body weight, peak dead-time correction factor, counting rates, and residual scatter bias for accurate cardiac myocardial blood flow imaging were 3-14 MBq/kg, 1.5-4.0, 22-64 Mcps singles and 4-14 Mcps prompt coincidence counting rates, and 2%-10% on the investigated scanners. Nonuniformity of the myocardial activity distribution varied from 3% to 16%. Accurate dynamic imaging is possible on the 10 3D PET systems if the maximum injected MBq/kg values are respected to limit peak dead-time losses during the bolus first-pass transit. © 2017 by the Society of Nuclear Medicine and Molecular Imaging.

5nsec Dead time multichannel scaling system for Mössbauer spectrometer

NASA Astrophysics Data System (ADS)

Verrastro, C.; Trombetta, G.; Pita, A.; Saragovi, C.; Duhalde, S.

1991-11-01

A PC programmable and fast multichannel scaling module has been designed to use a commercial Mössbauer spectrometer. This module is based on a 10 single chip 8 bits microcomputer (MC6805) and on a 35 fast ALU, which allows a high performance and low cost system. The module can operate in a stand-alone mode. Data analysis are performed in real time display, on XT/AT IBM PC or compatibles. The channels are ranged between 256 and 4096, the maximum number of counts is 232-1 per channel, the dwell time is 3 μsec and the dead time between channels is 5 nsec. A friendly software display the real time spectrum and offers menues with different options at each state.

Validation of a Monte Carlo simulation of the Philips Allegro/GEMINI PET systems using GATE

NASA Astrophysics Data System (ADS)

Lamare, F.; Turzo, A.; Bizais, Y.; Cheze LeRest, C.; Visvikis, D.

2006-02-01

A newly developed simulation toolkit, GATE (Geant4 Application for Tomographic Emission), was used to develop a Monte Carlo simulation of a fully three-dimensional (3D) clinical PET scanner. The Philips Allegro/GEMINI PET systems were simulated in order to (a) allow a detailed study of the parameters affecting the system's performance under various imaging conditions, (b) study the optimization and quantitative accuracy of emission acquisition protocols for dynamic and static imaging, and (c) further validate the potential of GATE for the simulation of clinical PET systems. A model of the detection system and its geometry was developed. The accuracy of the developed detection model was tested through the comparison of simulated and measured results obtained with the Allegro/GEMINI systems for a number of NEMA NU2-2001 performance protocols including spatial resolution, sensitivity and scatter fraction. In addition, an approximate model of the system's dead time at the level of detected single events and coincidences was developed in an attempt to simulate the count rate related performance characteristics of the scanner. The developed dead-time model was assessed under different imaging conditions using the count rate loss and noise equivalent count rates performance protocols of standard and modified NEMA NU2-2001 (whole body imaging conditions) and NEMA NU2-1994 (brain imaging conditions) comparing simulated with experimental measurements obtained with the Allegro/GEMINI PET systems. Finally, a reconstructed image quality protocol was used to assess the overall performance of the developed model. An agreement of <3% was obtained in scatter fraction, with a difference between 4% and 10% in the true and random coincidence count rates respectively, throughout a range of activity concentrations and under various imaging conditions, resulting in <8% differences between simulated and measured noise equivalent count rates performance. Finally, the image quality validation study revealed a good agreement in signal-to-noise ratio and contrast recovery coefficients for a number of different volume spheres and two different (clinical level based) tumour-to-background ratios. In conclusion, these results support the accurate modelling of the Philips Allegro/GEMINI PET systems using GATE in combination with a dead-time model for the signal flow description, which leads to an agreement of <10% in coincidence count rates under different imaging conditions and clinically relevant activity concentration levels.

GUMAP: A GUPIXWIN-compatible code for extracting regional spectra from nuclear microbeam list mode files

NASA Astrophysics Data System (ADS)

Russell, John L.; Campbell, John L.; Boyd, Nicholas I.; Dias, Johnny F.

2018-02-01

The newly developed GUMAP software creates element maps from OMDAQ list mode files, displays these maps individually or collectively, and facilitates on-screen definitions of specified regions from which a PIXE spectrum can be built. These include a free-hand region defined by moving the cursor. The regional charge is entered automatically into the spectrum file in a new GUPIXWIN-compatible format, enabling a GUPIXWIN analysis of the spectrum. The code defaults to the OMDAQ dead time treatment but also facilitates two other methods for dead time correction in sample regions with count rates different from the average.

FPGA-based photon-counting phase-modulation fluorometer and a brief comparison with that operated in a pulsed-excitation mode

NASA Astrophysics Data System (ADS)

Iwata, Tetsuo; Taga, Takanori; Mizuno, Takahiko

2018-02-01

We have constructed a high-efficiency, photon-counting phase-modulation fluorometer (PC-PMF) using a field-programmable gate array, which is a modified version of the photon-counting fluorometer (PCF) that works in a pulsed-excitation mode (Iwata and Mizuno in Meas Sci Technol 28:075501, 2017). The common working principle for both is the simultaneous detection of the photoelectron pulse train, which covers 64 ns with a 1.0-ns resolution time (1.0 ns/channel). The signal-gathering efficiency was improved more than 100 times over that of conventional time-correlated single-photon-counting at the expense of resolution time depending on the number of channels. The system dead time for building a histogram was eliminated, markedly shortening the measurement time for fluorescent samples with moderately high quantum yields. We describe the PC-PMF and make a brief comparison with the pulsed-excitation PCF in precision, demonstrating the potential advantage of PC-PMF.

Swift J1822.3-1606: pre-outburst ROSAT limits (plus erratum)

NASA Astrophysics Data System (ADS)

Esposito, P.; Rea, N.; Israel, G. L.; Tieng, A.

2011-07-01

We report on a pre-outburst ROSAT PSPC observation of the new SGR discovered by Swift-BAT on 2011 July 14 (Cummings et al. Atel #3488). The PSPC observation was performed on 1993 September 12 for ~6.7ks. We find a source at: RA (2000) = 18 22 18.1 and Dec (2000)= -16 04 26.4, with a 5sigma detection significance. The count-rate (corrected for the PSPC PSF, sampling dead time, and vignetting) is about 0.012 counts/s.

Half-life determination for {sup 108}Ag and {sup 110}Ag

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zahn, Guilherme S.; Genezini, Frederico A.

2014-11-11

In this work, the half-life of the short-lived silver radionuclides {sup 108}Ag and {sup 110}Ag were measured by following the activity of samples after they were irradiated in the IEA-R1 reactor. The results were then fitted using a non-paralizable dead time correction to the regular exponential decay and the individual half-life values obtained were then analyzed using both the Normalized Residuals and the Rajeval techniques, in order to reach the most exact and precise final values. To check the validity of dead-time correction, a second correction method was also employed by means of counting a long-lived {sup 60}Co radioactive sourcemore » together with the samples as a livetime chronometer. The final half-live values obtained using both dead-time correction methods were in good agreement, showing that the correction was properly assessed. The results obtained are partially compatible with the literature values, but with a lower uncertainty, and allow a discussion on the last ENSDF compilations' values.« less

Accurate live and dead bacterial cell enumeration using flow cytometry (Conference Presentation)

NASA Astrophysics Data System (ADS)

Ou, Fang; McGoverin, Cushla; Swift, Simon; Vanholsbeeck, Frédérique

2017-03-01

Flow cytometry (FCM) is based on the detection of scattered light and fluorescence to identify cells with particular characteristics of interest. However most FCM cannot precisely control the flow through its interrogation point and hence the volume and concentration of the sample cannot be immediately obtained. The easiest, most reliable and inexpensive way of obtaining absolute counts with FCM is by using reference beads. We investigated a method of using FCM with reference beads to measure live and dead bacterial concentration over the range of 106 to 108 cells/mL and ratio varying from 0 to 100%. We believe we are the first to use this method for such a large cell concentration range while also establishing the effect of varying the live/dead bacteria ratios. Escherichia coli solutions with differing ratios of live:dead cells were stained with fluorescent dyes SYTO 9 and propidium iodide (PI), which label live and dead cells, respectively. Samples were measured using a LSR II Flow Cytometer (BD Biosciences); using 488 nm excitation with 20 mW power. Both SYTO 9 and PI fluorescence were collected and threshold was set to side scatter. Traditional culture-based plate count was done in parallel to the FCM analysis. The concentration of live bacteria from FCM was compared to that obtained by plate counts. Preliminary results show that the concentration of live bacteria obtained by FCM and plate counts correlate well with each other and indicates this may be extended to a wider concentration range or for studying other cell characteristics.

Advanced active quenching circuit for ultra-fast quantum cryptography.

PubMed

Stipčević, Mario; Christensen, Bradley G; Kwiat, Paul G; Gauthier, Daniel J

2017-09-04

Commercial photon-counting modules based on actively quenched solid-state avalanche photodiode sensors are used in a wide variety of applications. Manufacturers characterize their detectors by specifying a small set of parameters, such as detection efficiency, dead time, dark counts rate, afterpulsing probability and single-photon arrival-time resolution (jitter). However, they usually do not specify the range of conditions over which these parameters are constant or present a sufficient description of the characterization process. In this work, we perform a few novel tests on two commercial detectors and identify an additional set of imperfections that must be specified to sufficiently characterize their behavior. These include rate-dependence of the dead time and jitter, detection delay shift, and "twilighting". We find that these additional non-ideal behaviors can lead to unexpected effects or strong deterioration of the performance of a system using these devices. We explain their origin by an in-depth analysis of the active quenching process. To mitigate the effects of these imperfections, a custom-built detection system is designed using a novel active quenching circuit. Its performance is compared against two commercial detectors in a fast quantum key distribution system with hyper-entangled photons and a random number generator.

The determination of the pulse pile-up reject (PUR) counting for X and gamma ray spectrometry

NASA Astrophysics Data System (ADS)

Karabıdak, S. M.; Kaya, S.

2017-02-01

The collection the charged particles produced by the incident radiation on a detector requires a time interval. If this time interval is not sufficiently short compared with the peaking time of the amplifier, a loss in the recovered signal amplitude occurs. Another major constraint on the throughput of modern x or gamma-ray spectrometers is the time required for the subsequent the pulse processing by the electronics. Two above-mentioned limitations are cause of counting losses resulting from the dead time and the pile-up. The pulse pile-up is a common problem in x and gamma ray radiation detection systems. The pulses pile-up in spectroscopic analysis can cause significant errors. Therefore, inhibition of these pulses is a vital step. A way to reduce errors due to the pulse pile-up is a pile-up inspection circuitry (PUR). Such a circuit rejects some of the pulse pile-up. Therefore, this circuit leads to counting losses. Determination of these counting losses is an important problem. In this work, a new method is suggested for the determination of the pulse pile-up reject.

Characterizing energy dependence and count rate performance of a dual scintillator fiber-optic detector for computed tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoerner, Matthew R., E-mail: mrh5038@ufl.edu; Stepusin, Elliott J.; Hyer, Daniel E.

Purpose: Kilovoltage (kV) x-rays pose a significant challenge for radiation dosimetry. In the kV energy range, even small differences in material composition can result in significant variations in the absorbed energy between soft tissue and the detector. In addition, the use of electronic systems in light detection has demonstrated measurement losses at high photon fluence rates incident to the detector. This study investigated the feasibility of using a novel dual scintillator detector and whether its response to changes in beam energy from scatter and hardening is readily quantified. The detector incorporates a tissue-equivalent plastic scintillator and a gadolinium oxysulfide scintillator,more » which has a higher sensitivity to scatter x-rays. Methods: The detector was constructed by coupling two scintillators: (1) small cylindrical plastic scintillator, 500 μm in diameter and 2 mm in length, and (2) 100 micron sheet of gadolinium oxysulfide 500 μm in diameter, each to a 2 m long optical fiber, which acts as a light guide to transmit scintillation photons from the sensitive element to a photomultiplier tube. Count rate linearity data were obtained from a wide range of exposure rates delivered from a radiological x-ray tube by adjusting the tube current. The data were fitted to a nonparalyzable dead time model to characterize the time response. The true counting rate was related to the reference free air dose air rate measured with a 0.6 cm{sup 3} Radcal{sup ®} thimble chamber as described in AAPM Report No. 111. Secondary electron and photon spectra were evaluated using Monte Carlo techniques to analyze ionization quenching and photon energy-absorption characteristics from free-in-air and in phantom measurements. The depth/energy dependence of the detector was characterized using a computed tomography dose index QA phantom consisting of nested adult head and body segments. The phantom provided up to 32 cm of acrylic with a compatible 0.6 cm{sup 3} calibrated ionization chamber to measure the reference air kerma. Results: Each detector exhibited counting losses of 5% when irradiated at a dose rate of 26.3 mGy/s (Gadolinium) and 324.3 mGy/s (plastic). The dead time of the gadolinium oxysulfide detector was determined to be 48 ns, while the dead time of the plastic scintillating detector was unable to accurately be calculated due to poor counting statistics from low detected count rates. Noticeable depth/energy dependence was observed for the plastic scintillator for depths greater than 16 cm of acrylic that was not present for measurements using the gadolinium oxysulfide scintillator, leading us to believe that quenching may play a larger role in the depth dependence of the plastic scintillator than the incident x-ray energy spectrum. When properly corrected for dead time effects, the energy response of the gadolinium oxysulfide scintillator is consistent with the plastic scintillator. Using the integrated dual detector method was superior to each detector individually as the depth-dependent measure of dose was correctable to less than 8% between 100 and 135 kV. Conclusions: The dual scintillator fiber-optic detector accommodates a methodology for energy dependent corrections of the plastic scintillator, improving the overall accuracy of the dosimeter across the range of diagnostic energies.« less

Characterizing energy dependence and count rate performance of a dual scintillator fiber-optic detector for computed tomography.

PubMed

Hoerner, Matthew R; Stepusin, Elliott J; Hyer, Daniel E; Hintenlang, David E

2015-03-01

Kilovoltage (kV) x-rays pose a significant challenge for radiation dosimetry. In the kV energy range, even small differences in material composition can result in significant variations in the absorbed energy between soft tissue and the detector. In addition, the use of electronic systems in light detection has demonstrated measurement losses at high photon fluence rates incident to the detector. This study investigated the feasibility of using a novel dual scintillator detector and whether its response to changes in beam energy from scatter and hardening is readily quantified. The detector incorporates a tissue-equivalent plastic scintillator and a gadolinium oxysulfide scintillator, which has a higher sensitivity to scatter x-rays. The detector was constructed by coupling two scintillators: (1) small cylindrical plastic scintillator, 500 μm in diameter and 2 mm in length, and (2) 100 micron sheet of gadolinium oxysulfide 500 μm in diameter, each to a 2 m long optical fiber, which acts as a light guide to transmit scintillation photons from the sensitive element to a photomultiplier tube. Count rate linearity data were obtained from a wide range of exposure rates delivered from a radiological x-ray tube by adjusting the tube current. The data were fitted to a nonparalyzable dead time model to characterize the time response. The true counting rate was related to the reference free air dose air rate measured with a 0.6 cm(3) Radcal(®) thimble chamber as described in AAPM Report No. 111. Secondary electron and photon spectra were evaluated using Monte Carlo techniques to analyze ionization quenching and photon energy-absorption characteristics from free-in-air and in phantom measurements. The depth/energy dependence of the detector was characterized using a computed tomography dose index QA phantom consisting of nested adult head and body segments. The phantom provided up to 32 cm of acrylic with a compatible 0.6 cm(3) calibrated ionization chamber to measure the reference air kerma. Each detector exhibited counting losses of 5% when irradiated at a dose rate of 26.3 mGy/s (Gadolinium) and 324.3 mGy/s (plastic). The dead time of the gadolinium oxysulfide detector was determined to be 48 ns, while the dead time of the plastic scintillating detector was unable to accurately be calculated due to poor counting statistics from low detected count rates. Noticeable depth/energy dependence was observed for the plastic scintillator for depths greater than 16 cm of acrylic that was not present for measurements using the gadolinium oxysulfide scintillator, leading us to believe that quenching may play a larger role in the depth dependence of the plastic scintillator than the incident x-ray energy spectrum. When properly corrected for dead time effects, the energy response of the gadolinium oxysulfide scintillator is consistent with the plastic scintillator. Using the integrated dual detector method was superior to each detector individually as the depth-dependent measure of dose was correctable to less than 8% between 100 and 135 kV. The dual scintillator fiber-optic detector accommodates a methodology for energy dependent corrections of the plastic scintillator, improving the overall accuracy of the dosimeter across the range of diagnostic energies.

Indirect measurement of three-photon correlation in nonclassical light sources

NASA Astrophysics Data System (ADS)

Ann, Byoung-moo; Song, Younghoon; Kim, Junki; Yang, Daeho; An, Kyungwon

2016-06-01

We observe the three-photon correlation in nonclassical light sources by using an indirect measurement scheme based on the dead-time effect of photon-counting detectors. We first develop a general theory which enables us to extract the three-photon correlation from the two-photon correlation of an arbitrary light source measured with detectors with finite dead times. We then confirm the validity of our measurement scheme in experiments done with a cavity-QED microlaser operating with a large intracavity mean photon number exhibiting both sub- and super-Poissonian photon statistics. The experimental results are in good agreement with the theoretical expectation. Our measurement scheme provides an alternative approach for N -photon correlation measurement employing (N -1 ) detectors and thus a reduced measurement time for a given signal-to-noise ratio, compared to the usual scheme requiring N detectors.

Scatter Fraction, Count Rates, and Noise Equivalent Count Rate of a Single-Bed Position RPC TOF-PET System Assessed by Simulations Following the NEMA NU2-2001 Standards

NASA Astrophysics Data System (ADS)

Couceiro, Miguel; Crespo, Paulo; Marques, Rui F.; Fonte, Paulo

2014-06-01

Scatter Fraction (SF) and Noise Equivalent Count Rate (NECR) of a 2400 mm wide axial field-of-view Positron Emission Tomography (PET) system based on Resistive Plate Chamber (RPC) detectors with 300 ps Time Of Flight (TOF) resolution were studied by simulation using Geant4. The study followed the NEMA NU2-2001 standards, using the standard 700 mm long phantom and an axially extended one with 1800 mm, modeling the foreseeable use of this PET system. Data was processed based on the actual RPC readout, which requires a 0.2 μs non-paralyzable dead time for timing signals and a paralyzable dead time (τps) for position signals. For NECR, the best coincidence trigger consisted of a multiple time window coincidence sorter retaining single coincidence pairs (involving only two photons) and all possible coincidence pairs obtained from Multiple coincidences, keeping only those for which the direct TOF-reconstructed point falls inside a tight region surrounding the phantom. For the 700 mm phantom, the SF was 51.8% and, with τps = 3.0 μs, the peak NECR was 167 kcps at 7.6 kBq/cm3. Using τps = 1.0 μs the NECR was 349 kcps at 7.6 kBq/cm3, and no peak was found. For the 1800 mm phantom, the SF was slightly higher, and the NECR curves were identical to those obtained with the standard phantom, but shifted to lower activity concentrations. Although the higher SF, the values obtained for NECR allow concluding that the proposed scanner is expected to outperform current commercial PET systems.

Mercury and drought along the lower Carson River, Nevada: IV. Snowy egret post-fledging dispersal, timing of migration and survival, 2002–2004

USGS Publications Warehouse

Henny, Charles J.; Hill, Elwood F.; Grove, Robert A.; Chelgren, Nathan; Haggerty, Patricia K.

2017-01-01

This telemetry study is an extension of our 1997–2006 research on historical mercury contamination on snowy egrets (Egretta thula) up to ~ 20 days of age. Findings from initial studies at the mercury-contaminated Carson River colony at Lahontan Reservoir (LR) and a similar-sized reference (REF) colony on the Humboldt River included mercury-related physiological, biochemical, histopathological and reproductive effects up to ~20 days of age; with poor water years (2000–04), i.e., reduced prey availability, exacerbating effects. Herein, we compare timing of dispersal and migration at LR vs. REF, but the primary question now addressed is “whether survival of young mercury-exposed snowy egrets from LR would be further compromised beyond ~20 days of age? ” Based upon telemetry signals until 90–110 days of age (including dead bird counts and survival rate estimates), we conclude that mercury did not further compromise survival. Dead bird counts and survival rate estimates included time in the colony when fed by adults, plus the critical period when young dispersed from the colony to forage independently. The extended drought during this 3-year study was most critical in 2002 when production of ~20 d old egrets at LR was only 0.24 young/nest. In 2002, survival rates were low at both colonies and we documented the highest counts of dead egrets for both colonies. We suggest the losses in 2002 beyond 20 days of age were more a function of prey availability influenced by drought than exposure to mercury, especially at LR, because higher mercury concentrations, higher survival rates and fewer dead birds were documented at LR in 2003 when water conditions improved. Furthermore, total mercury (THg) in blood in 2003 was more than double 2002 (geometric mean, 3.39 vs 1.47 µg/g wet weight (ww). This higher THg exposure at LR in 2003 was associated with a redistribution of parent and post-dispersal feeding activities upstream (where there was higher mercury from historic mining) related to slightly improved water levels. When comparing the 3-year telemetry findings based upon ~20 d old young at LR (blood THg, geo. means 1.47, 3.39 and 1.89 µg/g ww), we found no evidence that age at dispersal, Julian date at dispersal, timing of migration, or pre-migration survival (~20 to ~100 days post-hatch) were adversely affected by elevated mercury.

Mercury and drought along the lower Carson River, Nevada: IV. Snowy egret post-fledging dispersal, timing of migration and survival, 2002-2004.

PubMed

Henny, Charles J; Hill, Elwood F; Grove, Robert A; Chelgren, Nathan D; Haggerty, Patricia K

2017-01-01

This telemetry study is an extension of our 1997-2006 research on historical mercury contamination on snowy egrets (Egretta thula) up to ~ 20 days of age. Findings from initial studies at the mercury-contaminated Carson River colony at Lahontan Reservoir (LR) and a similar-sized reference (REF) colony on the Humboldt River included mercury-related physiological, biochemical, histopathological and reproductive effects up to ~20 days of age; with poor water years (2000-04), i.e., reduced prey availability, exacerbating effects. Herein, we compare timing of dispersal and migration at LR vs. REF, but the primary question now addressed is "whether survival of young mercury-exposed snowy egrets from LR would be further compromised beyond ~20 days of age? " Based upon telemetry signals until 90-110 days of age (including dead bird counts and survival rate estimates), we conclude that mercury did not further compromise survival. Dead bird counts and survival rate estimates included time in the colony when fed by adults, plus the critical period when young dispersed from the colony to forage independently. The extended drought during this 3-year study was most critical in 2002 when production of ~20d old egrets at LR was only 0.24 young/nest. In 2002, survival rates were low at both colonies and we documented the highest counts of dead egrets for both colonies. We suggest the losses in 2002 beyond 20 days of age were more a function of prey availability influenced by drought than exposure to mercury, especially at LR, because higher mercury concentrations, higher survival rates and fewer dead birds were documented at LR in 2003 when water conditions improved. Furthermore, total mercury (THg) in blood in 2003 was more than double 2002 (geometric mean, 3.39 vs 1.47µg/g wet weight (ww). This higher THg exposure at LR in 2003 was associated with a redistribution of parent and post-dispersal feeding activities upstream (where there was higher mercury from historic mining) related to slightly improved water levels. When comparing the 3-year telemetry findings based upon ~20d old young at LR (blood THg, geo. means 1.47, 3.39 and 1.89µg/g ww), we found no evidence that age at dispersal, Julian date at dispersal, timing of migration, or pre-migration survival (~20 to ~100 days post-hatch) were adversely affected by elevated mercury. Published by Elsevier Inc.

Advantageous Direct Quantification of Viable Closely Related Probiotics in Petit-Suisse Cheeses under In Vitro Gastrointestinal Conditions by Propidium Monoazide - qPCR

PubMed Central

Villarreal, Martha Lissete Morales; Padilha, Marina; Vieira, Antonio Diogo Silva; Franco, Bernadette Dora Gombossy de Melo; Martinez, Rafael Chacon Ruiz; Saad, Susana Marta Isay

2013-01-01

Species-specific Quantitative Real Time PCR (qPCR) alone and combined with the use of propidium monoazide (PMA) were used along with the plate count method to evaluate the survival of the probiotic strains Lactobacillus acidophilus La-5 and Bifidobacterium animalis subsp. lactis Bb-12, and the bacteriocinogenic and potentially probiotic strain Lactobacillus sakei subsp. sakei 2a in synbiotic (F1) and probiotic (F2) petit-suisse cheeses exposed throughout shelf-life to in vitro simulated gastrointestinal tract conditions. The three strains studied showed a reduction in their viability after the 6 h assay. Bb-12 displayed the highest survival capacity, above 72.6 and 74.6% of the initial populations, respectively, by plate count and PMA-qPCR, maintaining population levels in the range or above 6 log CFU/g. The prebiotic mix of inulin and FOS did not offer any additional protection for the strains against the simulated gastrointestinal environment. The microorganisms' populations were comparable among the three methods at the initial time of the assay, confirming the presence of mainly viable and culturable cells. However, with the intensification of the stress induced throughout the various stages of the in vitro test, the differences among the methods increased. The qPCR was not a reliable enumeration method for the quantification of intact bacterial populations, mixed with large numbers of injured and dead bacteria, as confirmed by the scanning electron microscopy results. Furthermore, bacteria plate counts were much lower (P<0.05) than with the PMA-qPCR method, suggesting the accumulation of stressed or dead microorganisms unable to form colonies. The use of PMA overcame the qPCR inability to differentiate between dead and alive cells. The combination of PMA and species-specific qPCR in this study allowed a quick and unequivocal way of enumeration of viable closely related species incorporated into probiotic and synbiotic petit-suisse cheeses and under stress conditions. PMID:24358142

Monte Carlo simulation of Ray-Scan 64 PET system and performance evaluation using GATE toolkit

NASA Astrophysics Data System (ADS)

Li, Suying; Zhang, Qiushi; Vuletic, Ivan; Xie, Zhaoheng; Yang, Kun; Ren, Qiushi

2017-02-01

In this study, we aimed to develop a GATE model for the simulation of Ray-Scan 64 PET scanner and model its performance characteristics. A detailed implementation of system geometry and physical process were included in the simulation model. Then we modeled the performance characteristics of Ray-Scan 64 PET system for the first time, based on National Electrical Manufacturers Association (NEMA) NU-2 2007 protocols and validated the model against experimental measurement, including spatial resolution, sensitivity, counting rates and noise equivalent count rate (NECR). Moreover, an accurate dead time module was investigated to simulate the counting rate performance. Overall results showed reasonable agreement between simulation and experimental data. The validation results showed the reliability and feasibility of the GATE model to evaluate major performance of Ray-Scan 64 PET system. It provided a useful tool for a wide range of research applications.

Molecular Probes: A Tool for Studying Toxicity of VOCs to P.Putida F1

NASA Astrophysics Data System (ADS)

Singh, R.; Olson, M. S.

2007-12-01

Volatile Organic Compounds (VOCs) are of great concern in ground water remediation, and are generally present in the form of NAPLs in subsurface environments. Among the various treatment technologies, in situ bioremediation is one of the most effective and low-cost treatment options. Many soil bacteria are reported to degrade these organic contaminants via metabolism (using them as a source of carbon to derive energy) or co- metabolism up to certain concentrations. However, larger concentrations of these contaminants are toxic to bacteria. Thus, in order to achieve successful bioremediation, it is important to determine the optimal concentrations of various contaminants that is beneficial for the activity and survival of degrading bacteria. The purpose of this study is to develop a novel method for toxicity analyses of VOC contaminants to the soil bacteria that degrade them. The present study is based on a two-color fluorescence assay of bacterial viability which facilitates actual counting of live and dead bacteria. Pseudomonas putida F1 cells were labeled with a LIVE/DEAD® BacLightTM bacterial viability kit (Invitrogen), which consists of a mixture of two dyes, SYTO 9 and propidium iodide, each with a different ability to penetrate healthy bacterial cells. Live cells stain green whereas propidium iodide (red dye) only penetrates cells with compromised membranes that are considered dead or dying. Stained cells were exposed to different concentrations of trichloroethylene (TCE) and toluene in sealed vials. Change in the concentrations of green and red cells were monitored over the time using fluorescence microscopy. UTHSCSA ImageTool software was used to count the live and dead cells in the images. It was observed that live (green) cell concentrations decreased and dead/damaged (red) cell concentrations increased over time when cells were exposed to TCE. No significant changes were observed in control experiments. Death rate constants calculated based on live cell disappearance and dead/damaged cell appearance were found to be approximately equal for TCE. Results will be presented in terms of dose response and death rate curves. Death rate constants and minimum inhibitory concentrations for survival of P. Putida F1 exposed to TCE and toluene will be compared.

Effects on birds of fenthion aerial application for mosquito control

USGS Publications Warehouse

DeWeese, L.R.; McEwen, L.C.; Settimi, L.A.; Deblinger, R.D.

1983-01-01

Effects on birds of an aerial application of fenthion, a potent organophosphorus cholinesterase (ChE)-inhibiting insecticide, were assessed on four study sites 1.8 to 3.6 km2 in size. These sites were located within 121.5 km2 of wet meadows treated with 47 g of fenthion (AI) per ha in ultralow- volume formulation. Assessment methods were searches for sick or dead birds, measurements of brain ChE activity in specimens found dead or collected alive at different time intervals, and counts of bird populations. After treatment, 99 birds and 15 mammals were found sick or dead; 106 of these were on one site. Brain ChE activity in dead birds was depressed sufficiently to indicate that death was caused by an anti-ChE substance. Brain ChE activity in three common bird species collected alive showed the greatest reduction 2 days postspray. Two of these species had ChE activity that was still significantly (P<0.05) depressed 15 days postspray. Bird populations declined most where mortality was heaviest. Fenthion sprayed for mosquito control was life threatening to many birds inhabiting treated meadows.

Neutron counting with cameras

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Esch, Patrick; Crisanti, Marta; Mutti, Paolo

2015-07-01

A research project is presented in which we aim at counting individual neutrons with CCD-like cameras. We explore theoretically a technique that allows us to use imaging detectors as counting detectors at lower counting rates, and transits smoothly to continuous imaging at higher counting rates. As such, the hope is to combine the good background rejection properties of standard neutron counting detectors with the absence of dead time of integrating neutron imaging cameras as well as their very good spatial resolution. Compared to Xray detection, the essence of thermal neutron detection is the nuclear conversion reaction. The released energies involvedmore » are of the order of a few MeV, while X-ray detection releases energies of the order of the photon energy, which is in the 10 KeV range. Thanks to advances in camera technology which have resulted in increased quantum efficiency, lower noise, as well as increased frame rate up to 100 fps for CMOS-type cameras, this more than 100-fold higher available detection energy implies that the individual neutron detection light signal can be significantly above the noise level, as such allowing for discrimination and individual counting, which is hard to achieve with X-rays. The time scale of CMOS-type cameras doesn't allow one to consider time-of-flight measurements, but kinetic experiments in the 10 ms range are possible. The theory is next confronted to the first experimental results. (authors)« less

PET Performance Evaluation of an MR-Compatible PET Insert

PubMed Central

Wu, Yibao; Catana, Ciprian; Farrell, Richard; Dokhale, Purushottam A.; Shah, Kanai S.; Qi, Jinyi; Cherry, Simon R.

2010-01-01

A magnetic resonance (MR) compatible positron emission tomography (PET) insert has been developed in our laboratory for simultaneous small animal PET/MR imaging. This system is based on lutetium oxyorthosilicate (LSO) scintillator arrays with position-sensitive avalanche photodiode (PSAPD) photodetectors. The PET performance of this insert has been measured. The average reconstructed image spatial resolution was 1.51 mm. The sensitivity at the center of the field of view (CFOV) was 0.35%, which is comparable to the simulation predictions of 0.40%. The average photopeak energy resolution was 25%. The scatter fraction inside the MRI scanner with a line source was 12% (with a mouse-sized phantom and standard 35 mm Bruker 1H RF coil), 7% (with RF coil only) and 5% (without phantom or RF coil) for an energy window of 350–650 keV. The front-end electronics had a dead time of 390 ns, and a trigger extension dead time of 7.32 μs that degraded counting rate performance for injected doses above ~0.75 mCi (28 MBq). The peak noise-equivalent count rate (NECR) of 1.27 kcps was achieved at 290 μCi (10.7 MBq). The system showed good imaging performance inside a 7-T animal MRI system; however improvements in data acquisition electronics and reduction of the coincidence timing window are needed to realize improved NECR performance. PMID:21072320

Heterosigma bloom and associated fish kill

USGS Publications Warehouse

Hershberger, P.K.; Rensel, J.E.; Postel, J.R.; Taub, F.B.

1997-01-01

A bloom of the harmful marine phytoplankton, Heterosigma carterae occurred in upper Case Inlet, south Puget Sound, Washington in late September, 1994, correlating with the presence of at least 35 dead salmon. This marks the first time that this alga has been closely correlated with a wild fish kill; in the past it was thought to be associated with kills of penned fish at fish farms only. We were informed of the presence of a possible harmful algal bloom and dead salinois Ilear the town of Allyn on 27 September and a team was formed to investigate. We arrived at the Allyn waterfront at 17:30 hours the same day. Prior to our arrival, state agency personnel walked approximatcly two miles of shoreline from the powerlines north of the dock, to the mouth of Sherwood Creek and conducted the only official count of dead fish present along the shore consisting of 12 coho salmon (Oncorhynchus kisutch), 11 chum salmon (Oncorhynchus keta), 12 chinook salmon (Oncorhynchus tschawytscha), one flat fish, and one sculpin on the morning of 9/27. Since previous harmful blooms of Heterosigma have resultedin the majority of net penreared salmon sinking to the bottom of pens, and only approximately two miles of shoreline were sampled, it is suspected that many more exposed fish may have succumbed than were counted. Witnesses who explored the east side of the bay reported seeing many dead salmon there as well, but no counts were made. State agency personnel who observed the fish kill reported seeing “dying fish coming to the beach, gulping at the surface, trying to get out of the water” Scavengers were seen consuming the salmon carcasses; these included two harbor seals, a house cat, and Hymenopteran insects. None suffered any noticeable acute ill effects. Although precise cause of death has not been ascertained, visual inspection of the reproductive organs from a deceased male chum salmon found on the shore at Allyn confirmed that the fish was not yet reproductively mature and therefore did not die from completion of the spawning process.

A nonstationary Poisson point process describes the sequence of action potentials over long time scales in lateral-superior-olive auditory neurons.

PubMed

Turcott, R G; Lowen, S B; Li, E; Johnson, D H; Tsuchitani, C; Teich, M C

1994-01-01

The behavior of lateral-superior-olive (LSO) auditory neurons over large time scales was investigated. Of particular interest was the determination as to whether LSO neurons exhibit the same type of fractal behavior as that observed in primary VIII-nerve auditory neurons. It has been suggested that this fractal behavior, apparent on long time scales, may play a role in optimally coding natural sounds. We found that a nonfractal model, the nonstationary dead-time-modified Poisson point process (DTMP), describes the LSO firing patterns well for time scales greater than a few tens of milliseconds, a region where the specific details of refractoriness are unimportant. The rate is given by the sum of two decaying exponential functions. The process is completely specified by the initial values and time constants of the two exponentials and by the dead-time relation. Specific measures of the firing patterns investigated were the interspike-interval (ISI) histogram, the Fano-factor time curve (FFC), and the serial count correlation coefficient (SCC) with the number of action potentials in successive counting times serving as the random variable. For all the data sets we examined, the latter portion of the recording was well approximated by a single exponential rate function since the initial exponential portion rapidly decreases to a negligible value. Analytical expressions available for the statistics of a DTMP with a single exponential rate function can therefore be used for this portion of the data. Good agreement was obtained among the analytical results, the computer simulation, and the experimental data on time scales where the details of refractoriness are insignificant.(ABSTRACT TRUNCATED AT 250 WORDS)

Dead-time correction for high-throughput fluorescence lifetime imaging microscopy (Conference Presentation)

NASA Astrophysics Data System (ADS)

Enderlein, Joerg; Ruhlandt, Daja; Chithik, Anna; Ebrecht, René; Wouters, Fred S.; Gregor, Ingo

2016-02-01

Fluorescence lifetime microscopy has become an important method of bioimaging, allowing not only to record intensity and spectral, but also lifetime information across an image. One of the most widely used methods of FLIM is based on Time-Correlated Single Photon Counting (TCSPC). In TCSPC, one determines this curve by exciting molecules with a periodic train of short laser pulses, and then measuring the time delay between the first recorded fluorescence photon after each exciting laser pulse. An important technical detail of TCSPC measurements is the fact that the delay times between excitation laser pulses and resulting fluorescence photons are always measured between a laser pulse and the first fluorescence photon which is detected after that pulse. At high count rates, this leads to so-called pile-up: ``early'' photons eclipse long-delay photons, resulting in heavily skewed TCSPC histograms. To avoid pile-up, a rule of thumb is to perform TCSPC measurements at photon count rates which are at least hundred times smaller than the laser-pulse excitation rate. The downside of this approach is that the fluorescence-photon count-rate is restricted to a value below one hundredth of the laser-pulse excitation-rate, reducing the overall speed with which a fluorescence signal can be measured. We present a new data evaluation method which provides pile-up corrected fluorescence decay estimates from TCSPC measurements at high count rates, and we demonstrate our method on FLIM of fluorescently labeled cells.

Design and characterization of a dead-time regime enhanced early photon projection imaging system

NASA Astrophysics Data System (ADS)

Sinha, L.; Fogarty, M.; Zhou, W.; Giudice, A.; Brankov, J. G.; Tichauer, K. M.

2018-04-01

Scattering of visible and near-infrared light in biological tissue reduces spatial resolution for imaging of tissues thicker than 100 μm. In this study, an optical projection imaging system is presented and characterized that exploits the dead-time characteristics typical of photon counting modules based on single photon avalanche diodes (SPADs). With this system, it is possible to attenuate the detection of more scattered late-arriving photons, such that detection of less scattered early-arriving photons can be enhanced with increased light intensity, without being impeded by the maximum count rate of the SPADs. The system has the potential to provide transmittance-based anatomical information or fluorescence-based functional information (with slight modification in the instrumentation) of biological samples with improved resolution in the mesoscopic domain (0.1-2 cm). The system design, calibration, stability, and performance were evaluated using simulation and experimental phantom studies. The proposed system allows for the detection of very-rare early-photons at a higher frequency and with a better signal-to-noise ratio. The experimental results demonstrated over a 3.4-fold improvement in the spatial resolution using early photon detection vs. conventional detection, and a 1000-fold improvement in imaging time using enhanced early detection vs. conventional early photon detection in a 4-mm thick phantom with a tissue-equivalent absorption coefficient of μa = 0.05 mm-1 and a reduced scattering coefficient of μs' = 5 mm-1.

Automated detection of sperm whale sounds as a function of abrupt changes in sound intensity

NASA Astrophysics Data System (ADS)

Walker, Christopher D.; Rayborn, Grayson H.; Brack, Benjamin A.; Kuczaj, Stan A.; Paulos, Robin L.

2003-04-01

An algorithm designed to detect abrupt changes in sound intensity was developed and used to identify and count sperm whale vocalizations and to measure boat noise. The algorithm is a MATLAB routine that counts the number of occurrences for which the change in intensity level exceeds a threshold. The algorithm also permits the setting of a ``dead time'' interval to prevent the counting of multiple pulses within a single sperm whale click. This algorithm was used to analyze digitally sampled recordings of ambient noise obtained from the Gulf of Mexico using near bottom mounted EARS buoys deployed as part of the Littoral Acoustic Demonstration Center experiment. Because the background in these data varied slowly, the result of the application of the algorithm was automated detection of sperm whale clicks and creaks with results that agreed well with those obtained by trained human listeners. [Research supported by ONR.

Age determination in manatees using growth-layer-group counts in bone

USGS Publications Warehouse

Marmontel, M.; O'Shea, T.J.; Kochman, H.I.; Humphrey, S.R.

1996-01-01

Growth layers were observed in histological preparations of bones of known-age, known minimum-age, and tetracycline-marked free-ranging and captive Florida manatees (Trichechus manatus latirostris), substantiating earlier preliminary findings of other studies. Detailed analysis of 17 new case histories showed that growth-layer group (GLG) counts in the periotic bone were consistent with known age, or time since tetracycline administration, but were less reliable in other bones. GLG counts were also made in periotic bones of 1,196 Florida manatees of unknown age found dead from 1974 through 1991. These counts were conducted in order to assess variability and to determine relationships among estimated age, size, sex, and degree of bone resorption. Resorption can interfere with accuracy of GLG counts. This effect does not occur until ages greater than about 15 yr and body lengths greater than 300 cm are attained. GLGs were also observed in periotic bones of Antillean manatees (Trichechus manatus manatus) but were not validated against known-age specimens. Use of GLG counts in the periotic bone is suitable for application to studies of population dynamics and other age-related aspects of manatee biology.

Research on Advanced NDE Methods for Aerospace Structures

DTIC Science & Technology

1989-09-01

IS RELEASABLE TO THE NATIONAL TECHNICAL INFORMATION SERVICE (NTIS), AT NTIS, IT WILL BE AVAILABLE TO THE GENERAL PUBLIC, INCLUDING FOREIGN NATIONS...Karpur, M.J. Ruddell, J.A.Fox, E.L. Klosterman and M.L. PaDD 13a. TYPE OF REPORT 13b. TIME COVERED 114. DATE OF REPORT (Year, Month, Day) 115. PAGE COUNT...spaced planes in advanced composite materials. That technique was used to simultaneously generate C-scan images of: (1) material defects in the "dead zones

Rapid quantification of live/dead lactic acid bacteria in probiotic products using high-sensitivity flow cytometry

NASA Astrophysics Data System (ADS)

He, Shengbin; Hong, Xinyi; Huang, Tianxun; Zhang, Wenqiang; Zhou, Yingxing; Wu, Lina; Yan, Xiaomei

2017-06-01

A laboratory-built high-sensitivity flow cytometer (HSFCM) was employed for the rapid and accurate detection of lactic acid bacteria (LAB) and their viability in probiotic products. LAB were stained with both the cell membrane-permeable SYTO 9 green-fluorescent nucleic acid stain and the red-fluorescent nucleic acid stain, propidium iodide, which penetrates only bacteria with compromised membranes. The side scatter and dual-color fluorescence signals of single bacteria were detected simultaneously by the HSFCM. Ultra-high temperature processing milk and skim milk spiked with Lactobacillus casei were used as the model systems for the optimization of sample pretreatment and staining. The viable LAB counts measured by the HSFCM were in good agreement with those of the plate count method, and the measured ratios between the live and dead LAB matched well with the theoretical ratios. The established method was successfully applied to the rapid quantification of live/dead LAB in yogurts and fermented milk beverages of different brands. Moreover, the concentration and viability status of LAB in ambient yogurt, a relatively new yet popular milk product in China, are also reported.

EIGER detector: application in macromolecular crystallography.

PubMed

Casanas, Arnau; Warshamanage, Rangana; Finke, Aaron D; Panepucci, Ezequiel; Olieric, Vincent; Nöll, Anne; Tampé, Robert; Brandstetter, Stefan; Förster, Andreas; Mueller, Marcus; Schulze-Briese, Clemens; Bunk, Oliver; Wang, Meitian

2016-09-01

The development of single-photon-counting detectors, such as the PILATUS, has been a major recent breakthrough in macromolecular crystallography, enabling noise-free detection and novel data-acquisition modes. The new EIGER detector features a pixel size of 75 × 75 µm, frame rates of up to 3000 Hz and a dead time as low as 3.8 µs. An EIGER 1M and EIGER 16M were tested on Swiss Light Source beamlines X10SA and X06SA for their application in macromolecular crystallography. The combination of fast frame rates and a very short dead time allows high-quality data acquisition in a shorter time. The ultrafine ϕ-slicing data-collection method is introduced and validated and its application in finding the optimal rotation angle, a suitable rotation speed and a sufficient X-ray dose are presented. An improvement of the data quality up to slicing at one tenth of the mosaicity has been observed, which is much finer than expected based on previous findings. The influence of key data-collection parameters on data quality is discussed.

Micron2 Lab: Microfluidic Microbiology Lab Project

NASA Technical Reports Server (NTRS)

Burton, Aaron; Botkin, Douglas; Castro, Sarah; Crucian, Brian

2015-01-01

Microbial monitoring during spaceflight is crucial to maintain crew health and ensure water purifications systems are functioning properly. Current protocols for in-flight enumeration of bacteria in potable water systems require culture based methods. In this project, we aim to develop a flight- and microgravity-compatible flow cytometer capable of counting total microbial counts in the water supply and differentiating live from dead bacteria.

The natural history of fetal cells in postpartum murine maternal lung and bone marrow: a two-stage phenomenon.

PubMed

Pritchard, Stephanie; Peter, Inga; Johnson, Kirby L; Bianchi, Diana W

2012-01-01

During pregnancy, fetal cells cross into the maternal organs where they reside postpartum. Evidence from multiple laboratories suggests that these microchimeric fetal cells contribute to maternal tissue repair after injury. In mouse models, most injury experiments are performed during pregnancy; however, in a clinical setting most injuries or diseases occur postpartum. Therefore, experiments using animal models should be designed to address questions in the time period following delivery. In order to provide a baseline for such experiments, we analyzed the natural history of fetal cells in the postpartum maternal organs. Female C57BL/6J mice were mated to males homozygous for the enhanced green fluorescent protein gene. Fetal cells in the maternal lungs and bone marrow were identified by their green fluorescence using in a high-speed flow cytometer and their counts were compared between the lung and bone marrow. Spearman correlation analysis was used to identify relationships between the duration of time postpartum and the cell counts and ratio of live and dead cells. Our results show that fetal cells persist in these organs until at least three months postpartum in healthy female mice. We show a two-stage decline, with an initial two and a half-week rapid clearance followed by a trend of gradual decrease. Additionally, an increase in the ratio of live to dead cells within the lung over time suggests that these cells may replicate in vivo. The results presented here will inform the design of future experiments and may have implications for women's health.

Performance evaluation of the Ingenuity TF PET/CT scanner with a focus on high count-rate conditions

NASA Astrophysics Data System (ADS)

Kolthammer, Jeffrey A.; Su, Kuan-Hao; Grover, Anu; Narayanan, Manoj; Jordan, David W.; Muzic, Raymond F.

2014-07-01

This study evaluated the positron emission tomography (PET) imaging performance of the Ingenuity TF 128 PET/computed tomography (CT) scanner which has a PET component that was designed to support a wider radioactivity range than is possible with those of Gemini TF PET/CT and Ingenuity TF PET/MR. Spatial resolution, sensitivity, count rate characteristics and image quality were evaluated according to the NEMA NU 2-2007 standard and ACR phantom accreditation procedures; these were supplemented by additional measurements intended to characterize the system under conditions that would be encountered during quantitative cardiac imaging with 82Rb. Image quality was evaluated using a hot spheres phantom, and various contrast recovery and noise measurements were made from replicated images. Timing and energy resolution, dead time, and the linearity of the image activity concentration, were all measured over a wide range of count rates. Spatial resolution (4.8-5.1 mm FWHM), sensitivity (7.3 cps kBq-1), peak noise-equivalent count rate (124 kcps), and peak trues rate (365 kcps) were similar to those of the Gemini TF PET/CT. Contrast recovery was higher with a 2 mm, body-detail reconstruction than with a 4 mm, body reconstruction, although the precision was reduced. The noise equivalent count rate peak was broad (within 10% of peak from 241-609 MBq). The activity measured in phantom images was within 10% of the true activity for count rates up to those observed in 82Rb cardiac PET studies.

Viability PCR, a Culture-Independent Method for Rapid and Selective Quantification of Viable Legionella pneumophila Cells in Environmental Water Samples▿

PubMed Central

Delgado-Viscogliosi, Pilar; Solignac, Lydie; Delattre, Jean-Marie

2009-01-01

PCR-based methods have been developed to rapidly screen for Legionella pneumophila in water as an alternative to time-consuming culture techniques. However, these methods fail to discriminate between live and dead bacteria. Here, we report a viability assay (viability PCR [v-PCR]) for L. pneumophila that combines ethidium monoazide bromide with quantitative real-time PCR (qPCR). The ability of v-PCR to differentiate viable from nonviable L. pneumophila cells was confirmed with permeabilizing agents, toluene, or isopropanol. v-PCR suppressed more than 99.9% of the L. pneumophila PCR signal in nonviable cultures and was able to discriminate viable cells in mixed samples. A wide range of physiological states, from culturable to dead cells, was observed with 64 domestic hot-water samples after simultaneous quantification of L. pneumophila cells by v-PCR, conventional qPCR, and culture methods. v-PCR counts were equal to or higher than those obtained by culture and lower than or equal to conventional qPCR counts. v-PCR was used to successfully monitor in vitro the disinfection efficacy of heating to 70°C and glutaraldehyde and chlorine curative treatments. The v-PCR method appears to be a promising and rapid technique for enumerating L. pneumophila bacteria in water and, in comparison with conventional qPCR techniques used to monitor Legionella, has the advantage of selectively amplifying only viable cells. PMID:19363080

The use of flow cytometry to accurately ascertain total and viable counts of Lactobacillus rhamnosus in chocolate.

PubMed

Raymond, Yves; Champagne, Claude P

2015-04-01

The goals of this study were to evaluate the precision and accuracy of flow cytometry (FC) methodologies in the evaluation of populations of probiotic bacteria (Lactobacillus rhamnosus R0011) in two commercial dried forms, and ascertain the challenges in enumerating them in a chocolate matrix. FC analyses of total (FC(T)) and viable (FC(V)) counts in liquid or dried cultures were almost two times more precise (reproducible) than traditional direct microscopic counts (DCM) or colony forming units (CFU). With FC, it was possible to ascertain low levels of dead cells (FC(D)) in fresh cultures, which is not possible with traditional CFU and DMC methodologies. There was no interference of chocolate solids on FC counts of probiotics when inoculation was above 10(7) bacteria per g. Addition of probiotics in chocolate at 40 °C resulted in a 37% loss in viable cells. Blending of the probiotic powder into chocolate was not uniform which raised a concern that the precision of viable counts could suffer. FCT data can serve to identify the correct inoculation level of a sample, and viable counts (FCV or CFU) can subsequently be better interpreted. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

Optimization, validation, and application of a real-time PCR protocol for quantification of viable bacterial cells in municipal sewage sludge and biosolids using reporter genes and Escherichia coli.

PubMed

van Frankenhuyzen, Jessica K; Trevors, Jack T; Flemming, Cecily A; Lee, Hung; Habash, Marc B

2013-11-01

Biosolids result from treatment of sewage sludge to meet jurisdictional standards, including pathogen reduction. Once government regulations are met, materials can be applied to agricultural lands. Culture-based methods are used to enumerate pathogen indicator microorganisms but may underestimate cell densities, which is partly due to bacteria existing in a viable but non-culturable physiological state. Viable indicators can also be quantified by realtime polymerase chain reaction (qPCR) used with propidium monoazide (PMA), a dye that inhibits amplification of DNA found extracellularly or in dead cells. The objectives of this study were to test an optimized PMA-qPCR method for viable pathogen detection in wastewater solids and to validate it by comparing results to data obtained by conventional plating. Reporter genes from genetically marked Pseudomonas sp. UG14Lr and Agrobacterium tumefaciens 542 cells were spiked into samples of primary sludge, and anaerobically digested and Lystek-treated biosolids as cell-free DNA, dead cells, viable cells, and mixtures of live and dead cells, followed by DNA extraction with and without PMA, and qPCR. The protocol was then used for Escherichia coli quantification in the three matrices, and results compared to plate counts. PMA-qPCR selectively detected viable cells, while inhibiting signals from cell-free DNA and DNA found in membrane-compromised cells. PMA-qPCR detected 0.5-1 log unit more viable E. coli cells in both primary solids and dewatered biosolids than plate counts. No viable E. coli was found in Lystek-treated biosolids. These data suggest PMA-qPCR may more accurately estimate pathogen cell numbers than traditional culture methods.

Multiplicity counting from fission detector signals with time delay effects

NASA Astrophysics Data System (ADS)

Nagy, L.; Pázsit, I.; Pál, L.

2018-03-01

In recent work, we have developed the theory of using the first three auto- and joint central moments of the currents of up to three fission chambers to extract the singles, doubles and triples count rates of traditional multiplicity counting (Pázsit and Pál, 2016; Pázsit et al., 2016). The objective is to elaborate a method for determining the fissile mass, neutron multiplication, and (α, n) neutron emission rate of an unknown assembly of fissile material from the statistics of the fission chamber signals, analogous to the traditional multiplicity counting methods with detectors in the pulse mode. Such a method would be an alternative to He-3 detector systems, which would be free from the dead time problems that would be encountered in high counting rate applications, for example the assay of spent nuclear fuel. A significant restriction of our previous work was that all neutrons born in a source event (spontaneous fission) were assumed to be detected simultaneously, which is not fulfilled in reality. In the present work, this restriction is eliminated, by assuming an independent, identically distributed random time delay for all neutrons arising from one source event. Expressions are derived for the same auto- and joint central moments of the detector current(s) as in the previous case, expressed with the singles, doubles, and triples (S, D and T) count rates. It is shown that if the time-dispersion of neutron detections is of the same order of magnitude as the detector pulse width, as they typically are in measurements of fast neutrons, the multiplicity rates can still be extracted from the moments of the detector current, although with more involved calibration factors. The presented formulae, and hence also the performance of the proposed method, are tested by both analytical models of the time delay as well as with numerical simulations. Methods are suggested also for the modification of the method for large time delay effects (for thermalised neutrons).

2016 NIST (133Xe) and Transfer (131mXe, 133mXe, 135Xe) Calibration Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, Troy A.

A significantly improved calibration of the High Purity Germanium detectors used by the Idaho National Laboratory Noble Gas Laboratory was performed during the annual NIST calibration. New sample spacers provide reproducible and secure support of samples at distances of 4, 12, 24, 50 and 100 cm. Bean, 15mL and 50mL Schlenk tube geometries were calibrated. Also included in this year’s calibration was a correlation of detector dead-time with sample activity that can be used to predict the schedule of counting the samples at each distance for each geometry. This schedule prediction will help staff members set calendar reminders so thatmore » collection of calibration data at each geometry will not be missed. This report also correlates the counting efficiencies between detectors, so that if the counting efficiency on one detector is not known, it can be estimated from the same geometry on another detector.« less

Real-Time Microfluidic Blood-Counting System for PET and SPECT Preclinical Pharmacokinetic Studies.

PubMed

Convert, Laurence; Lebel, Réjean; Gascon, Suzanne; Fontaine, Réjean; Pratte, Jean-François; Charette, Paul; Aimez, Vincent; Lecomte, Roger

2016-09-01

Small-animal nuclear imaging modalities have become essential tools in the development process of new drugs, diagnostic procedures, and therapies. Quantification of metabolic or physiologic parameters is based on pharmacokinetic modeling of radiotracer biodistribution, which requires the blood input function in addition to tissue images. Such measurements are challenging in small animals because of their small blood volume. In this work, we propose a microfluidic counting system to monitor rodent blood radioactivity in real time, with high efficiency and small detection volume (∼1 μL). A microfluidic channel is built directly above unpackaged p-i-n photodiodes to detect β-particles with maximum efficiency. The device is embedded in a compact system comprising dedicated electronics, shielding, and pumping unit controlled by custom firmware to enable measurements next to small-animal scanners. Data corrections required to use the input function in pharmacokinetic models were established using calibrated solutions of the most common PET and SPECT radiotracers. Sensitivity, dead time, propagation delay, dispersion, background sensitivity, and the effect of sample temperature were characterized. The system was tested for pharmacokinetic studies in mice by quantifying myocardial perfusion and oxygen consumption with (11)C-acetate (PET) and by measuring the arterial input function using (99m)TcO4 (-) (SPECT). Sensitivity for PET isotopes reached 20%-47%, a 2- to 10-fold improvement relative to conventional catheter-based geometries. Furthermore, the system detected (99m)Tc-based SPECT tracers with an efficiency of 4%, an outcome not possible through a catheter. Correction for dead time was found to be unnecessary for small-animal experiments, whereas propagation delay and dispersion within the microfluidic channel were accurately corrected. Background activity and sample temperature were shown to have no influence on measurements. Finally, the system was successfully used in animal studies. A fully operational microfluidic blood-counting system for preclinical pharmacokinetic studies was developed. Microfluidics enabled reliable and high-efficiency measurement of the blood concentration of most common PET and SPECT radiotracers with high temporal resolution in small blood volume. © 2016 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

Enhanced ν-optical time domain reflectometry using gigahertz sinusoidally gated InGaAs/InP single-photon avalanche detector

NASA Astrophysics Data System (ADS)

Zhang, Xuping; Shi, Yuanlei; Shan, Yuanyuan; Sun, Zhenhong; Qiao, Weiyan; Zhang, Yixin

2016-09-01

Optical time domain reflectometry (OTDR) is one of the most successful diagnostic tools for nondestructive attenuation measurement of a fiber link. To achieve better sensitivity, spatial resolution, and avoid dead-zone in conversional OTDR, a single-photon detector has been introduced to form the photon-counting OTDR (ν-OTDR). We have proposed a ν-OTDR system using a gigahertz sinusoidally gated InGaAs/InP single-photon avalanche detector (SPAD). Benefiting from the superior performance of a sinusoidal gated SPAD on dark count probability, gating frequency, and gate duration, our ν-OTDR system has achieved a dynamic range (DR) of 33.4 dB with 1 μs probe pulse width after an equivalent measurement time of 51 s. This obtainable DR corresponds to a sensing length over 150 km. Our system has also obtained a spatial resolution of 5 cm at the end of a 5-km standard single-mode fiber. By employing a sinusoidal gating technique, we have improved the ν-OTDR spatial resolution and significantly reduced the measurement time.

A new application of a sodium deoxycholate-propidium monoazide-quantitative PCR assay for rapid and sensitive detection of viable Cronobacter sakazakii in powdered infant formula.

PubMed

Zhou, Baoqing; Chen, Bolu; Wu, Xin; Li, Fan; Yu, Pei; Aguilar, Zoraida P; Wei, Hua; Xu, Hengyi

2016-12-01

A rapid, reliable, and sensitive method for the detection of Cronobacter sakazakii, a common foodborne pathogen that may cause serious neonatal disease, has been developed. In this study, a rapid real-time quantitative PCR (qPCR) assay combined with sodium deoxycholate (SD) and propidium monoazide (PMA) was developed to detect C. sakazakii contamination in powdered infant formula (PIF). This method could eliminate the interference from dead or injured bacteria. Optimization studies indicated that SD and PMA at 0.08% (wt/vol) and 5µg/mL, respectively, were the most appropriate. In addition, qPCR, PMA-qPCR, SD-PMA-qPCR, and plate count assays were used to account for the number of viable bacteria in cell suspensions that were exposed to a 55°C water bath at different length of time. As a result, the viable number by PMA-qPCR showed significantly higher than of the number from SD-PMA-qPCR or plate counts. The number of viable bacteria was consistent between SD-PMA-qPCR and traditional plate counts, which indicated that SD treatment could eliminate the interference from dead or injured cells. Using the optimized parameters, the limit of detection with the SD-PMA-qPCR assay was 3.3×10 2 cfu/mL and 4.4×10 2 cfu/g in pure culture and in spiked PIF, respectively. A similar detection limit of 5.6×10 2 cfu/g was obtained in the presence of the Staphylococcus aureus (10 7 cfu/mL). The combined SD-PMA-qPCR assay holds promise for the rapid detection of viable C. sakazakii in PIF. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Multilevel joint competing risk models

NASA Astrophysics Data System (ADS)

Karunarathna, G. H. S.; Sooriyarachchi, M. R.

2017-09-01

Joint modeling approaches are often encountered for different outcomes of competing risk time to event and count in many biomedical and epidemiology studies in the presence of cluster effect. Hospital length of stay (LOS) has been the widely used outcome measure in hospital utilization due to the benchmark measurement for measuring multiple terminations such as discharge, transferred, dead and patients who have not completed the event of interest at the follow up period (censored) during hospitalizations. Competing risk models provide a method of addressing such multiple destinations since classical time to event models yield biased results when there are multiple events. In this study, the concept of joint modeling has been applied to the dengue epidemiology in Sri Lanka, 2006-2008 to assess the relationship between different outcomes of LOS and platelet count of dengue patients with the district cluster effect. Two key approaches have been applied to build up the joint scenario. In the first approach, modeling each competing risk separately using the binary logistic model, treating all other events as censored under the multilevel discrete time to event model, while the platelet counts are assumed to follow a lognormal regression model. The second approach is based on the endogeneity effect in the multilevel competing risks and count model. Model parameters were estimated using maximum likelihood based on the Laplace approximation. Moreover, the study reveals that joint modeling approach yield more precise results compared to fitting two separate univariate models, in terms of AIC (Akaike Information Criterion).

Biodiversity of Cryptofauna (Decapods) and Their Correlation with Dead Coral Pocillopora sp. Volume at Bunaken Island, North Sulawesi

NASA Astrophysics Data System (ADS)

Malik, Muhammad Danie Al; Kholilah, Nenik; Kurniasih, Eka Maya; Sembiring, Andrianus; Pertiwi, Ni Putu Dian; Ambariyanto, Ambariyanto; Munasik, Munasik; Meyer, Christopher

2018-02-01

Decapod is known as cryptofauna which is also important component of coral reef biodiversity. Dead corals are one of the area which usually used by decapods to live. This research aims to observe the diversity of cryptofauna (decapods) and the correlation between the number of decapods with the volume of dead corals. Ten dead corals, Pocillopora sp., were collected at 5 m depth at Bunaken Island. These dead corals were measured their volume and all decapods found were counted and identified up to family level. The richness and abundance were analyzed using ACE (Abundance-Based Coverage Estimates) and Chao 1. The results show that there were in total 474 decapods from 13 families found within all ten dead corals. Xanthidae was showed as the most abundance family among all, with 161 individual. Diversity index of decapods was found at medium category with value of 2.01. Rarefaction curve based on richness and abundance showed an estimation of 13 families. The result also indicated that the asymptote stage was reached on the 10th dead coral samples. The correlation between decapod with the volume of dead coral were showed significant positive correlation (r = 0.673, p<0.05). This result provides benefits to basic knowledge about diversity of decapod which one of cryptofauna as component fauna have a habitat on coral reef ecosystem.

Improved methods for the enumeration of heterotrophic bacteria in bottled mineral waters.

PubMed

Ramalho, R; Cunha, J; Teixeira, P; Gibbs, P A

2001-03-01

At this time the European Union regulations require that the heterotrophic plate counts (HPC) of mineral waters be assessed at two recovery temperatures: 22 degrees C for 72 h and 37 degrees C for 24 h. This procedure is time consuming and expensive. Development of new rapid methods for microbiological assessment of the microbial flora in the bottled water is an industry-driven need. The objectives of this work were to develop a method for the HPC that utilises only one recovery temperature and one incubation period and evaluate the use of, the LIVE/DEAD(R) BacLight Bacterial Viability Kit, 5-cyano-2,3-ditotyl tetrazolium chloride (CTC) and impedance methods to enumerate viable bacteria in bottled mineral water. Results showed that incubation at 30 degrees C could be used instead of incubation at 22 degrees C and 37 degrees C. Good correlation exists between counts at 30 degrees C and counts at 22 degrees C (r>0.90) and all the pathogens important in mineral water analyses grow similarly at 30 degrees C and 37 degrees C during 24 h. It was demonstrated that impedance methods might be useful to the mineral water industry as a rapid indicator of microbiological quality of the water. Results obtained with BacLight and CTC were similar to those obtained with plate counts.

Label-Free in Situ Discrimination of Live and Dead Bacteria by Surface-Enhanced Raman Scattering.

PubMed

Zhou, Haibo; Yang, Danting; Ivleva, Natalia P; Mircescu, Nicoleta E; Schubert, Sören; Niessner, Reinhard; Wieser, Andreas; Haisch, Christoph

2015-07-07

Techniques to distinguish between live and dead bacteria in a quantitative manner are in high demand in numerous fields including medical care, food safety, and public security as well as basic science research. This work demonstrates new nanostructures (silver nanoparticles coating bacteria structure, Bacteria@AgNPs) and their utility for rapid counting of live and dead bacteria by surface-enhanced Raman scattering (SERS). We found that suspensions containing Gram-negative organisms as well as AgNPs give strong SERS signals of live bacteria when generated selectively on the particle surface. However, almost no SERS signals can be detected from Bacteria@AgNPs suspensions containing dead bacteria. We demonstrate successful quantification of different percentages of dead bacteria both in bulk liquid and on glass surfaces by using SERS mapping on a single cell basis. Furthermore, different chemicals have been used to elucidate the mechanism involved in this observation. Finally, we used the Bacteria@AgNPs method to detect antibiotic resistance of E. coli strains against several antibiotics used in human medicine.

40 CFR Appendix II to Part 1068 - Emission-Related Parameters and Specifications

Code of Federal Regulations, 2014 CFR

2014-07-01

... valve lash dimension. 4. Camshaft timing. a. Valve opening—intake exhaust (degrees from top-dead center or bottom-dead center). b. Valve closing—intake exhaust (degrees from top-dead center or bottom-dead.... Opening timing (degrees from top-dead center or bottom-dead center). c. Closing timing (degrees from top...

40 CFR Appendix II to Part 1068 - Emission-Related Parameters and Specifications

Code of Federal Regulations, 2012 CFR

2012-07-01

... valve lash dimension. 4. Camshaft timing. a. Valve opening—intake exhaust (degrees from top-dead center or bottom-dead center). b. Valve closing—intake exhaust (degrees from top-dead center or bottom-dead.... Opening timing (degrees from top-dead center or bottom-dead center). c. Closing timing (degrees from top...

40 CFR Appendix II to Part 1068 - Emission-Related Parameters and Specifications

Code of Federal Regulations, 2013 CFR

2013-07-01

... valve lash dimension. 4. Camshaft timing. a. Valve opening—intake exhaust (degrees from top-dead center or bottom-dead center). b. Valve closing—intake exhaust (degrees from top-dead center or bottom-dead.... Opening timing (degrees from top-dead center or bottom-dead center). c. Closing timing (degrees from top...

An important step forward in continuous spectroscopic imaging of ionising radiations using ASICs

NASA Astrophysics Data System (ADS)

Fessler, P.; Coffin, J.; Eberlé, H.; de Raad Iseli, C.; Hilt, B.; Huss, D.; Krummenacher, F.; Lutz, J. R.; Prévot, G.; Renouprez, A.; Sigward, M. H.; Schwaller, B.; Voltolini, C.

1999-01-01

Characterization results are given for an original ASIC allowing continuous acquisition of ionising radiation images in spectroscopic mode. Ionising radiation imaging in general and spectroscopic imaging in particular must primarily be guided by the attempt to decrease statistical noise, which requires detection systems designed to allow very high counting rates. Any source of dead time must therefore be avoided. Thus, the use of on-line corrections of the inevitable dispersion of characteristics between the large number of electronic channels of the detection system, shall be precluded. Without claiming to achieve ultimate noise levels, the work described is focused on how to prevent good individual acquisition channel noise performance from being totally destroyed by the dispersion between channels without introducing dead times. With this goal, we developed an automatic charge amplifier output voltage offset compensation system which operates regardless of the cause of the offset (detector or electronic). The main performances of the system are the following: the input equivalent noise charge is 190 e rms (input non connected, peaking time 500 ns), the highest gain is 255 mV/fC, the peaking time is adjustable between 200 ns and 2 μs and the power consumption is 10 mW per channel. The agreement between experimental data and theoretical simulation results is excellent.

A physics investigation of deadtime losses in neutron counting at low rates with Cf252

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Louise G; Croft, Stephen

2009-01-01

{sup 252}Cf spontaneous fission sources are used for the characterization of neutron counters and the determination of calibration parameters; including both neutron coincidence counting (NCC) and neutron multiplicity deadtime (DT) parameters. Even at low event rates, temporally-correlated neutron counting using {sup 252}Cf suffers a deadtime effect. Meaning that in contrast to counting a random neutron source (e.g. AmLi to a close approximation), DT losses do not vanish in the low rate limit. This is because neutrons are emitted from spontaneous fission events in time-correlated 'bursts', and are detected over a short period commensurate with their lifetime in the detector (characterizedmore » by the system die-away time, {tau}). Thus, even when detected neutron events from different spontaneous fissions are unlikely to overlap in time, neutron events within the detected 'burst' are subject to intrinsic DT losses. Intrinsic DT losses for dilute Pu will be lower since the multiplicity distribution is softer, but real items also experience self-multiplication which can increase the 'size' of the bursts. Traditional NCC DT correction methods do not include the intrinsic (within burst) losses. We have proposed new forms of the traditional NCC Singles and Doubles DT correction factors. In this work, we apply Monte Carlo neutron pulse train analysis to investigate the functional form of the deadtime correction factors for an updating deadtime. Modeling is based on a high efficiency {sup 3}He neutron counter with short die-away time, representing an ideal {sup 3}He based detection system. The physics of dead time losses at low rates is explored and presented. It is observed that new forms are applicable and offer more accurate correction than the traditional forms.« less

Escherichia coli viability determination using dynamic light scattering: a comparison with standard methods.

PubMed

Loske, Achim M; Tello, Elba M; Vargas, Susana; Rodriguez, Rogelio

2014-08-01

To determine the concentration of bacteria in a sample is important in the food industry, medicine and biotechnology. A disadvantage of the plate-counting method is that a microorganism colony could arise from one cell or from many cells. The other standard methodology, known as optical density determination, is based on the turbidity of a suspension and registers all bacteria, dead and alive. In this article, dynamic light scattering is proposed as a fast and reliable method to determine bacterial viability and, consequently, time evolution. Escherichia coli was selected because this microorganism is well known and easy to handle. A correlation between the data from these three techniques was obtained. We were able to calculate the growth rate, usually determined by plate counting or optical density measurement, using dynamic light scattering and to predict bacterial behavior. An analytical relationship between the colony forming units and the light scattered intensity was also deduced.

40 CFR Appendix II to Part 1068 - Emission-Related Parameters and Specifications

Code of Federal Regulations, 2011 CFR

2011-07-01

... dimension. 4. Camshaft timing. a. Valve opening—intake exhaust (degrees from top-dead center or bottom-dead center). b. Valve closing—intake exhaust (degrees from top-dead center or bottom-dead center). c. Valve... (degrees from top-dead center or bottom-dead center). c. Closing timing (degrees from top-dead center or...

40 CFR Appendix II to Part 1068 - Emission-Related Parameters and Specifications

Code of Federal Regulations, 2010 CFR

2010-07-01

... dimension. 4. Camshaft timing. a. Valve opening—intake exhaust (degrees from top-dead center or bottom-dead center). b. Valve closing—intake exhaust (degrees from top-dead center or bottom-dead center). c. Valve... (degrees from top-dead center or bottom-dead center). c. Closing timing (degrees from top-dead center or...

Bunch mode specific rate corrections for PILATUS3 detectors

DOE PAGES

Trueb, P.; Dejoie, C.; Kobas, M.; ...

2015-04-09

PILATUS X-ray detectors are in operation at many synchrotron beamlines around the world. This article reports on the characterization of the new PILATUS3 detector generation at high count rates. As for all counting detectors, the measured intensities have to be corrected for the dead-time of the counting mechanism at high photon fluxes. The large number of different bunch modes at these synchrotrons as well as the wide range of detector settings presents a challenge for providing accurate corrections. To avoid the intricate measurement of the count rate behaviour for every bunch mode, a Monte Carlo simulation of the counting mechanismmore » has been implemented, which is able to predict the corrections for arbitrary bunch modes and a wide range of detector settings. This article compares the simulated results with experimental data acquired at different synchrotrons. It is found that the usage of bunch mode specific corrections based on this simulation improves the accuracy of the measured intensities by up to 40% for high photon rates and highly structured bunch modes. For less structured bunch modes, the instant retrigger technology of PILATUS3 detectors substantially reduces the dependency of the rate correction on the bunch mode. The acquired data also demonstrate that the instant retrigger technology allows for data acquisition up to 15 million photons per second per pixel.« less

Measuring partial fluorescence yield using filtered detectors.

PubMed

Boyko, T D; Green, R J; Moewes, A; Regier, T Z

2014-07-01

Typically, X-ray absorption near-edge structure measurements aim to probe the linear attenuation coefficient. These measurements are often carried out using partial fluorescence yield techniques that rely on detectors having photon energy discrimination improving the sensitivity and the signal-to-background ratio of the measured spectra. However, measuring the partial fluorescence yield in the soft X-ray regime with reasonable efficiency requires solid-state detectors, which have limitations due to the inherent dead-time while measuring. Alternatively, many of the available detectors that are not energy dispersive do not suffer from photon count rate limitations. A filter placed in front of one of these detectors will make the energy-dependent efficiency non-linear, thereby changing the responsivity of the detector. It is shown that using an array of filtered X-ray detectors is a viable method for measuring soft X-ray partial fluorescence yield spectra without dead-time. The feasibility of this technique is further demonstrated using α-Fe2O3 as an example and it is shown that this detector technology could vastly improve the photon collection efficiency at synchrotrons and that these detectors will allow experiments to be completed with a much lower photon flux reducing X-ray-induced damage.

No Time for Dead Time: Use the Fourier Amplitude Differences to Normalize Dead-time-affected Periodograms

NASA Astrophysics Data System (ADS)

Bachetti, Matteo; Huppenkothen, Daniela

2018-02-01

Dead time affects many of the instruments used in X-ray astronomy, by producing a strong distortion in power density spectra. This can make it difficult to model the aperiodic variability of the source or look for quasi-periodic oscillations. Whereas in some instruments a simple a priori correction for dead-time-affected power spectra is possible, this is not the case for others such as NuSTAR, where the dead time is non-constant and long (∼2.5 ms). Bachetti et al. (2015) suggested the cospectrum obtained from light curves of independent detectors within the same instrument as a possible way out, but this solution has always only been a partial one: the measured rms was still affected by dead time because the width of the power distribution of the cospectrum was modulated by dead time in a frequency-dependent way. In this Letter, we suggest a new, powerful method to normalize dead-time-affected cospectra and power density spectra. Our approach uses the difference of the Fourier amplitudes from two independent detectors to characterize and filter out the effect of dead time. This method is crucially important for the accurate modeling of periodograms derived from instruments affected by dead time on board current missions like NuSTAR and Astrosat, but also future missions such as IXPE.

Biological object recognition in μ-radiography images

NASA Astrophysics Data System (ADS)

Prochazka, A.; Dammer, J.; Weyda, F.; Sopko, V.; Benes, J.; Zeman, J.; Jandejsek, I.

2015-03-01

This study presents an applicability of real-time microradiography to biological objects, namely to horse chestnut leafminer, Cameraria ohridella (Insecta: Lepidoptera, Gracillariidae) and following image processing focusing on image segmentation and object recognition. The microradiography of insects (such as horse chestnut leafminer) provides a non-invasive imaging that leaves the organisms alive. The imaging requires a high spatial resolution (micrometer scale) radiographic system. Our radiographic system consists of a micro-focus X-ray tube and two types of detectors. The first is a charge integrating detector (Hamamatsu flat panel), the second is a pixel semiconductor detector (Medipix2 detector). The latter allows detection of single quantum photon of ionizing radiation. We obtained numerous horse chestnuts leafminer pupae in several microradiography images easy recognizable in automatic mode using the image processing methods. We implemented an algorithm that is able to count a number of dead and alive pupae in images. The algorithm was based on two methods: 1) noise reduction using mathematical morphology filters, 2) Canny edge detection. The accuracy of the algorithm is higher for the Medipix2 (average recall for detection of alive pupae =0.99, average recall for detection of dead pupae =0.83), than for the flat panel (average recall for detection of alive pupae =0.99, average recall for detection of dead pupae =0.77). Therefore, we conclude that Medipix2 has lower noise and better displays contours (edges) of biological objects. Our method allows automatic selection and calculation of dead and alive chestnut leafminer pupae. It leads to faster monitoring of the population of one of the world's important insect pest.

ASNC upgrade for nuclear material accountancy of ACPF

NASA Astrophysics Data System (ADS)

Seo, Hee; Ahn, Seong-Kyu; Lee, Chaehun; Oh, Jong-Myeong; Yoon, Seonkwang

2018-02-01

A safeguards neutron coincidence counter for nuclear material accountancy of the Advanced spent-fuel Conditioning Process Facility (ACPF), known as the ACP Safeguards Neutron Counter (ASNC), was upgraded to improve its remote-handling and maintenance capabilities. Based on the results of the previous design study, the neutron counter was completely rebuilt, and various detector parameters for neutron coincidence counting (i.e., high-voltage plateau, efficiency profile, dead time, die-away time, gate length, doubles gate fraction, and stability) were experimentally determined. The measurement data showed good agreement with the MCNP simulation results. To the best of the authors' knowledge, the ASNC is the only safeguards neutron coincidence counter in the world that is installed and operated in a hot-cell. The final goals to be achieved were (1) to evaluate the uncertainty level of the ASNC in nuclear material accountancy of the process materials of the oxide-reduction process for spent fuels and (2) to evaluate the applicability of the neutron coincidence counting technique within a strong radiation field (e.g., in a hot-cell environment).

Effect of Cypermethrin on the Growth of Ciliate Protozoan Paramecium caudatum.

PubMed

Dutta, Joydeep

2015-01-01

The objective of this study is to assess the effect of cypermethrin on the growth of ciliate protozoan Paramecium caudatum. Monoxenic culture of P. caudatum, were exposed to different doses (0.01, 0.05, 0.1, 0.15, and 0.2 µg/L) of cypermethrin along with control for 24, 48, 72, and 96 h time interval. The total numbers of live and dead cells were counted after trypan blue staining in Neubauer hemocytometer. Marked decrease in the number of living cells with the increase in the concentration of cypermethrin and with increasing exposure time intervals was recorded. The results indicate that cypermethrin is toxic to P. caudatum even at low concentrations when it enters in the aquatic system through runoff.

High-speed multi-exposure laser speckle contrast imaging with a single-photon counting camera

PubMed Central

Dragojević, Tanja; Bronzi, Danilo; Varma, Hari M.; Valdes, Claudia P.; Castellvi, Clara; Villa, Federica; Tosi, Alberto; Justicia, Carles; Zappa, Franco; Durduran, Turgut

2015-01-01

Laser speckle contrast imaging (LSCI) has emerged as a valuable tool for cerebral blood flow (CBF) imaging. We present a multi-exposure laser speckle imaging (MESI) method which uses a high-frame rate acquisition with a negligible inter-frame dead time to mimic multiple exposures in a single-shot acquisition series. Our approach takes advantage of the noise-free readout and high-sensitivity of a complementary metal-oxide-semiconductor (CMOS) single-photon avalanche diode (SPAD) array to provide real-time speckle contrast measurement with high temporal resolution and accuracy. To demonstrate its feasibility, we provide comparisons between in vivo measurements with both the standard and the new approach performed on a mouse brain, in identical conditions. PMID:26309751

Active quench and reset integrated circuit with novel hold-off time control logic for Geiger-mode avalanche photodiodes.

PubMed

Deng, Shijie; Morrison, Alan P

2012-09-15

This Letter presents an active quench-and-reset circuit for Geiger-mode avalanche photodiodes (GM-APDs). The integrated circuit was fabricated using a conventional 0.35 μm complementary metal oxide semiconductor process. Experimental results show that the circuit is capable of linearly setting the hold-off time from several nanoseconds to microseconds with a resolution of 6.5 ns. This allows the selection of the optimal afterpulse-free hold-off time for the GM-APD via external digital inputs or additional signal processing circuitry. Moreover, this circuit resets the APD automatically following the end of the hold-off period, thus simplifying the control for the end user. Results also show that a minimum dead time of 28.4 ns is achieved, demonstrating a saturated photon-counting rate of 35.2 Mcounts/s.

Detection of E. coli O157:H7 from ground beef using Fourier transform infrared (FT-IR) spectroscopy and chemometrics.

PubMed

Davis, Reeta; Irudayaraj, Joseph; Reuhs, Bradley L; Mauer, Lisa J

2010-08-01

FT-IR spectroscopy methods for detection, differentiation, and quantification of E. coli O157:H7 strains separated from ground beef were developed. Filtration and immunomagnetic separation (IMS) were used to extract live and dead E. coli O157:H7 cells from contaminated ground beef prior to spectral acquisition. Spectra were analyzed using chemometric techniques in OPUS, TQ Analyst, and WinDAS software programs. Standard plate counts were used for development and validation of spectral analyses. The detection limit based on a selectivity value using the OPUS ident test was 10(5) CFU/g for both Filtration-FT-IR and IMS-FT-IR methods. Experiments using ground beef inoculated with fewer cells (10(1) to 10(2) CFU/g) reached the detection limit at 6 h incubation. Partial least squares (PLS) models with cross validation were used to establish relationships between plate counts and FT-IR spectra. Better PLS predictions were obtained for quantifying live E. coli O157:H7 strains (R(2)> or = 0.9955, RMSEE < or = 0.17, RPD > or = 14) and different ratios of live and dead E. coli O157:H7 cells (R(2)= 0.9945, RMSEE = 2.75, RPD = 13.43) from ground beef using Filtration-FT-IR than IMS-FT-IR methods. Discriminant analysis and canonical variate analysis (CVA) of the spectra differentiated various strains of E. coli O157:H7 from an apathogenic control strain. CVA also separated spectra of 100% dead cells separated from ground beef from spectra of 0.5% live cells in the presence of 99.5% dead cells of E. coli O157:H7. These combined separation and FT-IR methods could be useful for rapid detection and differentiation of pathogens in complex foods.

Array-scale performance of TES X-ray Calorimeters Suitable for Constellation-X

NASA Technical Reports Server (NTRS)

Kilbourne, C. A.; Bandler, S. R.; Brown, A. D.; Chervenak, J. A.; Eckart, M. E.; Finkbeiner, F. M.; Iyomoto, N.; Kelley, R. L.; Porter, F. S.; Smith, S. J.;

Effect of Detector Dead Time on the Performance of Optical Direct-Detection Communication Links

NASA Technical Reports Server (NTRS)

Chen, C.-C.

1988-01-01

Avalanche photodiodes (APDs) operating in the Geiger mode can provide a significantly improved single-photon detect ion sensitivity over conventional photodiodes. However, the quenching circuit required to remove the excess charge carriers after each photon event can introduce an undesirable dead time into the detection process. The effect of this detector dead time on the performance of a binary pulse-position-modulted (PPM) channel is studied by analyzing the error probability. It is shown that, when back- ground noise is negligible, the performance of the detector with dead time is similar to that o f a quantum-limited receiver. For systems with increasing background intensities, the error rate of the receiver starts to degrade rapidly with increasing dead time. The power penalty due to detector dead time is also evaluated and shown to depend critically on background intensity as well as dead time. Given the expected background strength in an optical channel, therefore, a constraint must be placed on the bandwidth of the receiver to limit the amount of power penalty due to detector dead time.

Effect of detector dead time on the performance of optical direct-detection communication links

NASA Astrophysics Data System (ADS)

Chen, C.-C.

1988-05-01

Avalanche photodiodes (APDs) operating in the Geiger mode can provide a significantly improved single-photon detection sensitivity over conventional photodiodes. However, the quenching circuit required to remove the excess charge carriers after each photon event can introduce an undesirable dead time into the detection process. The effect of this detector dead time on the performance of a binary pulse-position-modulated (PPM) channel is studied by analyzing the error probability. It is shown that, when background noise is negligible, the performance of the detector with dead time is similar to that of a quantum-limited receiver. For systems with increasing background intensities, the error rate of the receiver starts to degrade rapidly with increasing dead time. The power penalty due to detector dead time is also evaluated and shown to depend critically on badkground intensity as well as dead time. Given the expected background strength in an optical channel, therefore, a constraint must be placed on the bandwidth of the receiver to limit the amount of power penalty due to detector dead time.

Blocking Losses With a Photon Counter

NASA Technical Reports Server (NTRS)

Moision, Burce E.; Piazzolla, Sabino

2012-01-01

It was not known how to assess accurately losses in a communications link due to photodetector blocking, a phenomenon wherein a detector is rendered inactive for a short time after the detection of a photon. When used to detect a communications signal, blocking leads to losses relative to an ideal detector, which may be measured as a reduction in the communications rate for a given received signal power, or an increase in the signal power required to support the same communications rate. This work involved characterizing blocking losses for single detectors and arrays of detectors. Blocking may be mitigated by spreading the signal intensity over an array of detectors, reducing the count rate on any one detector. A simple approximation was made to the blocking loss as a function of the probability that a detector is unblocked at a given time, essentially treating the blocking probability as a scaling of the detection efficiency. An exact statistical characterization was derived for a single detector, and an approximation for multiple detectors. This allowed derivation of several accurate approximations to the loss. Methods were also derived to account for a rise time in recovery, and non-uniform illumination due to diffraction and atmospheric distortion of the phase front. It was assumed that the communications signal is intensity modulated and received by an array of photon-counting photodetectors. For the purpose of this analysis, it was assumed that the detectors are ideal, in that they produce a signal that allows one to reproduce the arrival times of electrons, produced either as photoelectrons or from dark noise, exactly. For single detectors, the performance of the maximum-likelihood (ML) receiver in blocking is illustrated, as well as a maximum-count (MC) receiver, that, when receiving a pulse-position-modulated (PPM) signal, selects the symbol corresponding to the slot with the largest electron count. Whereas the MC receiver saturates at high count rates, the ML receiver may not. The loss in capacity, symbol-error-rate (SER), and count-rate were numerically computed. It was shown that the capacity and symbol-error-rate losses track, whereas the count-rate loss does not generally reflect the SER or capacity loss, as the slot-statistics at the detector output are no longer Poisson. It is also shown that the MC receiver loss may be accurately predicted for dead times on the order of a slot.

RPA Data Wiz users guide, version 1.0

Treesearch

Scott A. Pugh

2004-01-01

RPA Data Wiz is a computer application use to create summary tables, graphs, and maps of Resource Planning Act (RPA) Assessment forest information (English or metric units). Volumes for growing stock, live cull, dead salvable, netgrowth, and mortality can be estimated. Acreage, biomass, and tree count estimates are also available.

Time and position sensitive single photon detector for scintillator read-out

NASA Astrophysics Data System (ADS)

Schössler, S.; Bromberger, B.; Brandis, M.; Schmidt, L. Ph H.; Tittelmeier, K.; Czasch, A.; Dangendorf, V.; Jagutzki, O.

2012-02-01

We have developed a photon counting detector system for combined neutron and γ radiography which can determine position, time and intensity of a secondary photon flash created by a high-energy particle or photon within a scintillator screen. The system is based on a micro-channel plate photomultiplier concept utilizing image charge coupling to a position- and time-sensitive read-out anode placed outside the vacuum tube in air, aided by a standard photomultiplier and very fast pulse-height analyzing electronics. Due to the low dead time of all system components it can cope with the high throughput demands of a proposed combined fast neutron and dual discrete energy γ radiography method (FNDDER). We show tests with different types of delay-line read-out anodes and present a novel pulse-height-to-time converter circuit with its potential to discriminate γ energies for the projected FNDDER devices for an automated cargo container inspection system (ACCIS).

Perturbative search for dead-end CFTs

DOE PAGES

Nakayama, Yu

2015-05-08

To explore the possibility of self-organized criticality, we look for CFTs without any relevant scalar deformations (a.k.a. dead-end CFTs) within power-counting renormalizable quantum field theories with a weakly coupled Lagrangian description. In three dimensions, the only candidates are pure (Abelian) gauge theories, which may be further deformed by Chern-Simons terms. In four dimensions, we show that there are infinitely many non-trivial candidates based on chiral gauge theories. Using the three-loop beta functions, we compute the gap of scaling dimensions above the marginal value, and it can be as small as O(10 –5) and robust against the perturbative corrections. These classesmore » of candidates are very weakly coupled and our perturbative conclusion seems difficult to refute. Furthermore, the hypothesis that non-trivial dead-end CFTs do not exist is likely to be false in four dimensions.« less

Perturbative search for dead-end CFTs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakayama, Yu

To explore the possibility of self-organized criticality, we look for CFTs without any relevant scalar deformations (a.k.a. dead-end CFTs) within power-counting renormalizable quantum field theories with a weakly coupled Lagrangian description. In three dimensions, the only candidates are pure (Abelian) gauge theories, which may be further deformed by Chern-Simons terms. In four dimensions, we show that there are infinitely many non-trivial candidates based on chiral gauge theories. Using the three-loop beta functions, we compute the gap of scaling dimensions above the marginal value, and it can be as small as O(10 –5) and robust against the perturbative corrections. These classesmore » of candidates are very weakly coupled and our perturbative conclusion seems difficult to refute. Furthermore, the hypothesis that non-trivial dead-end CFTs do not exist is likely to be false in four dimensions.« less

Unified dead-time compensation structure for SISO processes with multiple dead times.

PubMed

Normey-Rico, Julio E; Flesch, Rodolfo C C; Santos, Tito L M

2014-11-01

This paper proposes a dead-time compensation structure for processes with multiple dead times. The controller is based on the filtered Smith predictor (FSP) dead-time compensator structure and it is able to control stable, integrating, and unstable processes with multiple input/output dead times. An equivalent model of the process is first computed in order to define the predictor structure. Using this equivalent model, the primary controller and the predictor filter are tuned to obtain an internally stable closed-loop system which also attempts some closed-loop specifications in terms of set-point tracking, disturbance rejection, and robustness. Some simulation case studies are used to illustrate the good properties of the proposed approach. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

77 FR 64373 - Culturally Significant Objects Imported for Exhibition Determinations: “The Dead Sea Scrolls...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-19

... Determinations: ``The Dead Sea Scrolls: Life and Faith in Ancient Times,'' Formerly Titled ``The Dead Sea Scrolls... the Department of State pertaining to the exhibition ``The Dead Sea Scrolls: Life and Faith in Biblical Times.'' The referenced notice is corrected here to change the exhibition name to ``The Dead Sea...

78 FR 62354 - Culturally Significant Objects Imported for Exhibition Determinations: “The Dead Sea Scrolls...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-18

... Determinations: ``The Dead Sea Scrolls: Life and Faith in Ancient Times'' Formerly Titled ``The Dead Sea Scrolls... Department of State pertaining to the exhibition ``The Dead Sea Scrolls: Life and Faith in Biblical Times... of the Federal Register (volume 77, number 203) to change the exhibition name to ``The Dead Sea...

78 FR 24462 - Culturally Significant Objects Imported for Exhibition; Determinations: “The Dead Sea Scrolls...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-25

...; Determinations: ``The Dead Sea Scrolls: Life and Faith in Ancient Times'' Formerly Titled ``The Dead Sea Scrolls... Department of State pertaining to the exhibition ``The Dead Sea Scrolls: Life and Faith in Biblical Times... of the Federal Register (volume 77, number 203) to change the exhibition name to ``The Dead Sea...

78 FR 16565 - Culturally Significant Objects Imported for Exhibition Determinations: “The Dead Sea Scrolls...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-15

... Determinations: ``The Dead Sea Scrolls: Life and Faith in Ancient Times'' Formerly Titled ``The Dead Sea Scrolls... Department of State pertaining to the exhibition ``The Dead Sea Scrolls: Life and Faith in Biblical Times... of the Federal Register (volume 77, number 203) to change the exhibition name to ``The Dead Sea...

CD4 Count in HIV- Brain-Dead Donors: Insight into Donor Risk Assessment for HIV+ Donors.

PubMed

Serrano, Oscar Kenneth; Kerwin, Scott; Payne, William D; Pruett, Timothy L

2017-04-01

The Human Immunodeficiency Virus (HIV) Organ Policy Equity Act allows for transplantation of organs from HIV-infected individuals (HIV+), provided it is performed under a research protocol. The safety assessment of an organ for transplantation is an essential element of the donation process. The risk for HIV-associated opportunistic infections increases as circulating CD4+ lymphocytes decrease to less than 200 cells/μL; however, the numbers of circulating CD4+ cells in the HIV-negative (HIV-) brain-dead donor (BDD) is not known. Circulating T-lymphocyte subset profiles in conventional HIV- BDD were measured in 20 BDD in a clinical laboratory. The mean age of the BDD cohort was 48.7 years, 95% were white and 45% were women. The average body mass index was 29.2 kg/m. Cerebrovascular accident (40%) was the most prevalent cause of death. Sixteen (80%) subjects had a CD4 count ≤441 cells/μL (lower limit of normal) and 11 (55%) had a CD4 count less than 200 cells/μL; 11 (55%) subjects had a CD8 count ≤125 cells/μL (lower limit of normal). CD4/CD8 ratio was below normal in 3 patients (normal, 1.4-2.6). No recipient had a recognized donor-associated adverse event. Absolute numbers of CD4 and CD8 T-lymphocytes are commonly reduced after brain death in HIV- individuals. Thus, CD4 absolute numbers are an inconsistent metric for assessing organ donor risk, irrespective of HIV status.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, Steve; Haji-Sheikh, Michael; Huntington, Andrew

The Voxtel VX-798 is a prototype X-ray pixel array detector (PAD) featuring a silicon sensor photodiode array of 48 x 48 pixels, each 130 mu m x 130 mu m x 520 mu m thick, coupled to a CMOS readout application specific integrated circuit (ASIC). The first synchrotron X-ray characterization of this detector is presented, and its ability to selectively count individual X-rays within two independent arrival time windows, a programmable energy range, and localized to a single pixel is demonstrated. During our first trial run at Argonne National Laboratory's Advance Photon Source, the detector achieved a 60 ns gatingmore » time and 700 eV full width at half-maximum energy resolution in agreement with design parameters. Each pixel of the PAD holds two independent digital counters, and the discriminator for X-ray energy features both an upper and lower threshold to window the energy of interest discarding unwanted background. This smart-pixel technology allows energy and time resolution to be set and optimized in software. It is found that the detector linearity follows an isolated dead-time model, implying that megahertz count rates should be possible in each pixel. Measurement of the line and point spread functions showed negligible spatial blurring. When combined with the timing structure of the synchrotron storage ring, it is demonstrated that the area detector can perform both picosecond time-resolved X-ray diffraction and fluorescence spectroscopy measurements.« less

Effect of Cypermethrin on the Growth of Ciliate Protozoan Paramecium caudatum

PubMed Central

Dutta, Joydeep

2015-01-01

Objective: The objective of this study is to assess the effect of cypermethrin on the growth of ciliate protozoan Paramecium caudatum. Materials and Methods: Monoxenic culture of P. caudatum, were exposed to different doses (0.01, 0.05, 0.1, 0.15, and 0.2 µg/L) of cypermethrin along with control for 24, 48, 72, and 96 h time interval. The total numbers of live and dead cells were counted after trypan blue staining in Neubauer hemocytometer. Results: Marked decrease in the number of living cells with the increase in the concentration of cypermethrin and with increasing exposure time intervals was recorded. Conclusion: The results indicate that cypermethrin is toxic to P. caudatum even at low concentrations when it enters in the aquatic system through runoff. PMID:26862268

Assessing Honey Bee (Hymenoptera: Apidae) Foraging Populations and the Potential Impact of Pesticides on Eight U.S. Crops

PubMed Central

Frazier, Maryann T.; Mullin, Chris A.; Frazier, Jim L.; Ashcraft, Sara A.; Leslie, Tim W.; Mussen, Eric C.; Drummond, Frank A.

2015-01-01

Beekeepers who use honey bees (Apis mellifera L.) for crop pollination services, or have colonies making honey on or in close proximity to agricultural crops, are concerned about the reductions of colony foragers and ultimate weakening of their colonies. Pesticide exposure is a potential factor in the loss of foragers. During 2009–2010, we assessed changes in the field force populations of 9–10 colonies at one location per crop on each of the eight crops by counting departing foragers leaving colonies at regular intervals during the respective crop blooming periods. The number of frames of adult bees was counted before and after bloom period. For pesticide analysis, we collected dead and dying bees near the hives, returning foragers, crop flowers, trapped pollen, and corn-flowers associated with the cotton crop. The number of departing foragers changed over time in all crops except almonds; general patterns in foraging activity included declines (cotton), noticeable peaks and declines (alfalfa, blueberries, cotton, corn, and pumpkins), and increases (apples and cantaloupes). The number of adult bee frames increased or remained stable in all crops except alfalfa and cotton. A total of 53 different pesticide residues were identified in samples collected across eight crops. Hazard quotients (HQ) were calculated for the combined residues for all crop-associated samples and separately for samples of dead and dying bees. A decrease in the number of departing foragers in cotton was one of the most substantial crop-associated impacts and presented the highest pesticide risk estimated by a summed pesticide residue HQ. PMID:26453703

Absolute Enumeration of Probiotic Strains Lactobacillus acidophilus NCFM® and Bifidobacterium animalis subsp. lactis Bl-04 ® via Chip-Based Digital PCR.

PubMed

Hansen, Sarah J Z; Morovic, Wesley; DeMeules, Martha; Stahl, Buffy; Sindelar, Connie W

2018-01-01

The current standard for enumeration of probiotics to obtain colony forming units by plate counts has several drawbacks: long time to results, high variability and the inability to discern between bacterial strains. Accurate probiotic cell counts are important to confirm the delivery of a clinically documented dose for its associated health benefits. A method is described using chip-based digital PCR (cdPCR) to enumerate Bifidobacterium animalis subsp. lactis Bl-04 and Lactobacillus acidophilus NCFM both as single strains and in combination. Primers and probes were designed to differentiate the target strains against other strains of the same species using known single copy, genetic differences. The assay was optimized to include propidium monoazide pre-treatment to prevent amplification of DNA associated with dead probiotic cells as well as liberation of DNA from cells with intact membranes using bead beating. The resulting assay was able to successfully enumerate each strain whether alone or in multiplex. The cdPCR method had a 4 and 5% relative standard deviation (RSD) for Bl-04 and NCFM, respectively, making it more precise than plate counts with an industry accepted RSD of 15%. cdPCR has the potential to replace traditional plate counts because of its precision, strain specificity and the ability to obtain results in a matter of hours.

Development of Fast Measurement System of Neutron Emission Profile Using a Digital Signal Processing Technique in JT-60U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishikawa, M.; Shinohara, K.; Itoga, T.

2008-03-12

Neutron emission profiles are routinely measured in JT-60U Tokamak. Stinbene neuron detectors (SNDs), which combine a Stilbene organic crystal scintillation detector (Stilbene detector) with an analog neutron-gamma pulse shape discrimination (PSD) circuit, have been used to measure neutron flux efficiently. Although the SND has many advantages as a neutron detector, the maximum count rate is limited up to {approx}1x 10{sup 5} counts/s due to the dead time of the analog PSD circuit. To overcome this issue, a digital signal processing (DSP) system using a Flash-ADC has been developed. In this system, anode signals from the photomultiplier of the Stilbene detectormore » are fed to the Flash ADC and digitized. Then, the PSD between neutrons and gamma-rays are performed using software. The photomultiplier tube is also modified to suppress and correct gain fluctuation of the photomultiplier. The DSP system has been installed in the center channel of the vertical neutron collimator system in JT-60U and applied to measurements of neutron flux in JT-60U experiments. Neutron flux are successfully measured with count rate up to {approx}1x 10{sup 6} counts/s without the effect of pile up of detected pulses. The performance of the DSP system as a neutron detector is demonstrated.« less

A comparison of methods to assess the antimicrobial activity of nanoparticle combinations on bacterial cells.

PubMed

Bankier, Claire; Cheong, Yuen; Mahalingam, Suntharavathanan; Edirisinghe, Mohan; Ren, Guogang; Cloutman-Green, Elaine; Ciric, Lena

2018-01-01

Bacterial cell quantification after exposure to antimicrobial compounds varies widely throughout industry and healthcare. Numerous methods are employed to quantify these antimicrobial effects. With increasing demand for new preventative methods for disease control, we aimed to compare and assess common analytical methods used to determine antimicrobial effects of novel nanoparticle combinations on two different pathogens. Plate counts of total viable cells, flow cytometry (LIVE/DEAD BacLight viability assay) and qPCR (viability qPCR) were used to assess the antimicrobial activity of engineered nanoparticle combinations (NPCs) on Gram-positive (Staphylococcus aureus) and Gram-negative (Pseudomonas aeruginosa) bacteria at different concentrations (0.05, 0.10 and 0.25 w/v%). Results were analysed using linear models to assess the effectiveness of different treatments. Strong antimicrobial effects of the three NPCs (AMNP0-2) on both pathogens could be quantified using the plate count method and flow cytometry. The plate count method showed a high log reduction (>8-log) for bacteria exposed to high NPC concentrations. We found similar antimicrobial results using the flow cytometry live/dead assay. Viability qPCR analysis of antimicrobial activity could not be quantified due to interference of NPCs with qPCR amplification. Flow cytometry was determined to be the best method to measure antimicrobial activity of the novel NPCs due to high-throughput, rapid and quantifiable results.

Optimal whole-body PET scanner configurations for different volumes of LSO scintillator: a simulation study.

PubMed

Poon, Jonathan K; Dahlbom, Magnus L; Moses, William W; Balakrishnan, Karthik; Wang, Wenli; Cherry, Simon R; Badawi, Ramsey D

2012-07-07

The axial field of view (AFOV) of the current generation of clinical whole-body PET scanners range from 15-22 cm, which limits sensitivity and renders applications such as whole-body dynamic imaging or imaging of very low activities in whole-body cellular tracking studies, almost impossible. Generally, extending the AFOV significantly increases the sensitivity and count-rate performance. However, extending the AFOV while maintaining detector thickness has significant cost implications. In addition, random coincidences, detector dead time, and object attenuation may reduce scanner performance as the AFOV increases. In this paper, we use Monte Carlo simulations to find the optimal scanner geometry (i.e. AFOV, detector thickness and acceptance angle) based on count-rate performance for a range of scintillator volumes ranging from 10 to 93 l with detector thickness varying from 5 to 20 mm. We compare the results to the performance of a scanner based on the current Siemens Biograph mCT geometry and electronics. Our simulation models were developed based on individual components of the Siemens Biograph mCT and were validated against experimental data using the NEMA NU-2 2007 count-rate protocol. In the study, noise-equivalent count rate (NECR) was computed as a function of maximum ring difference (i.e. acceptance angle) and activity concentration using a 27 cm diameter, 200 cm uniformly filled cylindrical phantom for each scanner configuration. To reduce the effect of random coincidences, we implemented a variable coincidence time window based on the length of the lines of response, which increased NECR performance up to 10% compared to using a static coincidence time window for scanners with a large maximum ring difference values. For a given scintillator volume, the optimal configuration results in modest count-rate performance gains of up to 16% compared to the shortest AFOV scanner with the thickest detectors. However, the longest AFOV of approximately 2 m with 20 mm thick detectors resulted in performance gains of 25-31 times higher NECR relative to the current Siemens Biograph mCT scanner configuration.

Optimal whole-body PET scanner configurations for different volumes of LSO scintillator: a simulation study

PubMed Central

Poon, Jonathan K; Dahlbom, Magnus L; Moses, William W; Balakrishnan, Karthik; Wang, Wenli; Cherry, Simon R; Badawi, Ramsey D

2013-01-01

The axial field of view (AFOV) of the current generation of clinical whole-body PET scanners range from 15–22 cm, which limits sensitivity and renders applications such as whole-body dynamic imaging, or imaging of very low activities in whole-body cellular tracking studies, almost impossible. Generally, extending the AFOV significantly increases the sensitivity and count-rate performance. However, extending the AFOV while maintaining detector thickness has significant cost implications. In addition, random coincidences, detector dead time, and object attenuation may reduce scanner performance as the AFOV increases. In this paper, we use Monte Carlo simulations to find the optimal scanner geometry (i.e. AFOV, detector thickness and acceptance angle) based on count-rate performance for a range of scintillator volumes ranging from 10 to 90 l with detector thickness varying from 5 to 20 mm. We compare the results to the performance of a scanner based on the current Siemens Biograph mCT geometry and electronics. Our simulation models were developed based on individual components of the Siemens Biograph mCT and were validated against experimental data using the NEMA NU-2 2007 count-rate protocol. In the study, noise-equivalent count rate (NECR) was computed as a function of maximum ring difference (i.e. acceptance angle) and activity concentration using a 27 cm diameter, 200 cm uniformly filled cylindrical phantom for each scanner configuration. To reduce the effect of random coincidences, we implemented a variable coincidence time window based on the length of the lines of response, which increased NECR performance up to 10% compared to using a static coincidence time window for scanners with large maximum ring difference values. For a given scintillator volume, the optimal configuration results in modest count-rate performance gains of up to 16% compared to the shortest AFOV scanner with the thickest detectors. However, the longest AFOV of approximately 2 m with 20 mm thick detectors resulted in performance gains of 25–31 times higher NECR relative to the current Siemens Biograph mCT scanner configuration. PMID:22678106

Optimal whole-body PET scanner configurations for different volumes of LSO scintillator: a simulation study

NASA Astrophysics Data System (ADS)

Poon, Jonathan K.; Dahlbom, Magnus L.; Moses, William W.; Balakrishnan, Karthik; Wang, Wenli; Cherry, Simon R.; Badawi, Ramsey D.

2012-07-01

The axial field of view (AFOV) of the current generation of clinical whole-body PET scanners range from 15-22 cm, which limits sensitivity and renders applications such as whole-body dynamic imaging or imaging of very low activities in whole-body cellular tracking studies, almost impossible. Generally, extending the AFOV significantly increases the sensitivity and count-rate performance. However, extending the AFOV while maintaining detector thickness has significant cost implications. In addition, random coincidences, detector dead time, and object attenuation may reduce scanner performance as the AFOV increases. In this paper, we use Monte Carlo simulations to find the optimal scanner geometry (i.e. AFOV, detector thickness and acceptance angle) based on count-rate performance for a range of scintillator volumes ranging from 10 to 93 l with detector thickness varying from 5 to 20 mm. We compare the results to the performance of a scanner based on the current Siemens Biograph mCT geometry and electronics. Our simulation models were developed based on individual components of the Siemens Biograph mCT and were validated against experimental data using the NEMA NU-2 2007 count-rate protocol. In the study, noise-equivalent count rate (NECR) was computed as a function of maximum ring difference (i.e. acceptance angle) and activity concentration using a 27 cm diameter, 200 cm uniformly filled cylindrical phantom for each scanner configuration. To reduce the effect of random coincidences, we implemented a variable coincidence time window based on the length of the lines of response, which increased NECR performance up to 10% compared to using a static coincidence time window for scanners with a large maximum ring difference values. For a given scintillator volume, the optimal configuration results in modest count-rate performance gains of up to 16% compared to the shortest AFOV scanner with the thickest detectors. However, the longest AFOV of approximately 2 m with 20 mm thick detectors resulted in performance gains of 25-31 times higher NECR relative to the current Siemens Biograph mCT scanner configuration.

Multi-Rate Acquisition for Dead Time Reduction in Magnetic Resonance Receivers: Application to Imaging With Zero Echo Time.

PubMed

Marjanovic, Josip; Weiger, Markus; Reber, Jonas; Brunner, David O; Dietrich, Benjamin E; Wilm, Bertram J; Froidevaux, Romain; Pruessmann, Klaas P

2018-02-01

For magnetic resonance imaging of tissues with very short transverse relaxation times, radio-frequency excitation must be immediately followed by data acquisition with fast spatial encoding. In zero-echo-time (ZTE) imaging, excitation is performed while the readout gradient is already on, causing data loss due to an initial dead time. One major dead time contribution is the settling time of the filters involved in signal down-conversion. In this paper, a multi-rate acquisition scheme is proposed to minimize dead time due to filtering. Short filters and high output bandwidth are used initially to minimize settling time. With increasing time since the signal onset, longer filters with better frequency selectivity enable stronger signal decimation. In this way, significant dead time reduction is accomplished at only a slight increase in the overall amount of output data. Multi-rate acquisition was implemented with a two-stage filter cascade in a digital receiver based on a field-programmable gate array. In ZTE imaging in a phantom and in vivo, dead time reduction by multi-rate acquisition is shown to improve image quality and expand the feasible bandwidth while increasing the amount of data collected by only a few percent.

Effect of antibacterial dental adhesive on multispecies biofilms formation.

PubMed

Zhang, K; Wang, S; Zhou, X; Xu, H H K; Weir, M D; Ge, Y; Li, M; Wang, S; Li, Y; Xu, X; Zheng, L; Cheng, L

2015-04-01

Antibacterial adhesives have favorable prospects to inhibit biofilms and secondary caries. The objectives of this study were to investigate the antibacterial effect of dental adhesives containing dimethylaminododecyl methacrylate (DMADDM) on different bacteria in controlled multispecies biofilms and its regulating effect on development of biofilm for the first time. Antibacterial material was synthesized, and Streptococcus mutans, Streptococcus gordonii, and Streptococcus sanguinis were chosen to form multispecies biofilms. Lactic acid assay and pH measurement were conducted to study the acid production of controlled multispecies biofilms. Anthrone method and exopolysaccharide (EPS):bacteria volume ratio measured by confocal laser scanning microscopy were performed to determine the EPS production of biofilms. The colony-forming unit counts, scanning electron microscope imaging, and dead:live volume ratio decided by confocal laser scanning microscopy were used to study the biomass change of controlled multispecies biofilms. The TaqMan real-time polymerase chain reaction and fluorescent in situ hybridization imaging were used to study the proportion change in multispecies biofilms of different groups. The results showed that DMADDM-containing adhesive groups slowed the pH drop and decreased the lactic acid production noticeably, especially lactic acid production in the 5% DMADDM group, which decreased 10- to 30-fold compared with control group (P < 0.05). EPS was reduced significantly in 5% DMADDM group (P < 0.05). The DMADDM groups reduced the colony-forming unit counts significantly (P < 0.05) and had higher dead:live volume ratio in biofilms compared with control group (P < 0.05). The proportion of S. mutans decreased steadily in DMADDM-containing groups and continually increased in control group, and the biofilm had a more healthy development tendency after the regulation of DMADDM. In conclusion, the adhesives containing DMADDM had remarkable antimicrobial properties to serve as "bioactive" adhesive materials and revealed its potential value for antibiofilm and anticaries clinical applications. © International & American Associations for Dental Research 2015.

[Spatial pattern of land surface dead combustible fuel load in Huzhong forest area in Great Xing'an Mountains].

PubMed

Liu, Zhi-Hua; Chang, Yu; Chen, Hong-Wei; Zhou, Rui; Jing, Guo-Zhi; Zhang, Hong-Xin; Zhang, Chang-Meng

2008-03-01

By using geo-statistics and based on time-lag classification standard, a comparative study was made on the land surface dead combustible fuels in Huzhong forest area in Great Xing'an Mountains. The results indicated that the first level land surface dead combustible fuel, i. e., 1 h time-lag dead fuel, presented stronger spatial auto-correlation, with an average of 762.35 g x m(-2) and contributing to 55.54% of the total load. Its determining factors were species composition and stand age. The second and third levels land surface dead combustible fuel, i. e., 10 h and 100 h time-lag dead fuels, had a sum of 610.26 g x m(-2), and presented weaker spatial auto-correlation than 1 h time-lag dead fuel. Their determining factor was the disturbance history of forest stand. The complexity and heterogeneity of the factors determining the quality and quantity of forest land surface dead combustible fuels were the main reasons for the relatively inaccurate interpolation. However, the utilization of field survey data coupled with geo-statistics could easily and accurately interpolate the spatial pattern of forest land surface dead combustible fuel loads, and indirectly provide a practical basis for forest management.

Flexible ultrathin-body single-photon avalanche diode sensors and CMOS integration.

PubMed

Sun, Pengfei; Ishihara, Ryoichi; Charbon, Edoardo

2016-02-22

We proposed the world's first flexible ultrathin-body single-photon avalanche diode (SPAD) as photon counting device providing a suitable solution to advanced implantable bio-compatible chronic medical monitoring, diagnostics and other applications. In this paper, we investigate the Geiger-mode performance of this flexible ultrathin-body SPAD comprehensively and we extend this work to the first flexible SPAD image sensor with in-pixel and off-pixel electronics integrated in CMOS. Experimental results show that dark count rate (DCR) by band-to-band tunneling can be reduced by optimizing multiplication doping. DCR by trap-assisted avalanche, which is believed to be originated from the trench etching process, could be further reduced, resulting in a DCR density of tens to hundreds of Hertz per micrometer square at cryogenic temperature. The influence of the trench etching process onto DCR is also proved by comparison with planar ultrathin-body SPAD structures without trench. Photon detection probability (PDP) can be achieved by wider depletion and drift regions and by carefully optimizing body thickness. PDP in frontside- (FSI) and backside-illumination (BSI) are comparable, thus making this technology suitable for both modes of illumination. Afterpulsing and crosstalk are negligible at 2µs dead time, while it has been proved, for the first time, that a CMOS SPAD pixel of this kind could work in a cryogenic environment. By appropriate choice of substrate, this technology is amenable to implantation for biocompatible photon-counting applications and wherever bended imaging sensors are essential.

Inventory of forest and rangeland resources, including forest stress. [Atlanta, Georgia, Black Hills, and Manitou, Colorado test sites

NASA Technical Reports Server (NTRS)

Heller, R. C.; Aldrich, R. C.; Weber, F. P.; Driscoll, R. S. (Principal Investigator)

1974-01-01

The author has identified the following significant results. Some current beetle-killed ponderosa pine can be detected on S190-B photography imaged over the Bear Lodge mountains in the Black Hills National Forest. Detections were made on SL-3 imagery (September 13, 1973) using a zoom lens microscope to view the photography. At this time correlations have not been made to all of the known infestation spots in the Bear Lodge mountains; rather, known infestations have been located on the SL-3 imagery. It was determined that the beetle-killed trees were current kills by stereo viewing of SL-3 imagery on one side and SL-2 on the other. A successful technique was developed for mapping current beetle-killed pine using MSS imagery from mission 247 flown by the C-130 over the Black Hills test site in September 1973. Color enhancement processing on the NASA/JSC, DAS system using three MSS channels produced an excellent quality detection map for current kill pine. More importantly it provides a way to inventory the dead trees by relating PCM counts to actual numbers of dead trees.

Simulation of Simple Controlled Processes with Dead-Time.

ERIC Educational Resources Information Center

Watson, Keith R.; And Others

1985-01-01

The determination of closed-loop response of processes containing dead-time is typically not covered in undergraduate process control, possibly because the solution by Laplace transforms requires the use of Pade approximation for dead-time, which makes the procedure lengthy and tedious. A computer-aided method is described which simplifies the…

How dead is dead? Qualitative findings from participants of combined traditional and lead-time time trade-off valuations.

PubMed

Al Sayah, Fatima; Mladenovic, Ana; Gaebel, Kathryn; Xie, Feng; Johnson, Jeffrey A

2016-01-01

The EuroQol Valuation Technology (EQ-VT) uses traditional time trade-off (tTTO) for health states better than dead and lead-time TTO (LT-TTO) for states worse than dead to elicit a value (-1.0 to +1.0) for each health state. In the Canadian EQ-5D-5L Valuation study which used the EQVT platform, we observed an unexpected peak in frequency of "0" values and few negative values, particularly in the range of 0 to -0.5. To better understand this finding, we sought to explore respondents' thought processes while valuing a health state, and their understanding of the tTTO and LT-TTO exercises. Qualitative semi-structured interviews were conducted with EQVT task respondents. Questions focused on valuations of health states as: (a) Same as dead in tTTO, (b) Worse than dead in tTTO but changed to same as dead in LT-TTO, (c) Worse than dead in LT-TTO, and (d) Worse than dead in LT-TTO with trading off all 10 years. Data were analyzed using content and thematic analysis. Mean age of participants (N = 70) was 40 ± 18.1 years, 60% female, and 76% Caucasian. Participants provided similar reasons for valuing a health state same as or worse than dead. Many participants expressed confusion about worse than dead valuations, distinction between same as and worse than dead, and the transition from tTTO to LT-TTO. A few indicated that the addition of 10 years of full health in the LT-TTO influenced their valuations. The transition from tTTO to LT-TTO in the EQVT was confusing to participants, whereby some health state valuations around this transition appeared to be arbitrary.

X-ray characterization of a multichannel smart-pixel array detector.

PubMed

Ross, Steve; Haji-Sheikh, Michael; Huntington, Andrew; Kline, David; Lee, Adam; Li, Yuelin; Rhee, Jehyuk; Tarpley, Mary; Walko, Donald A; Westberg, Gregg; Williams, George; Zou, Haifeng; Landahl, Eric

2016-01-01

The Voxtel VX-798 is a prototype X-ray pixel array detector (PAD) featuring a silicon sensor photodiode array of 48 × 48 pixels, each 130 µm × 130 µm × 520 µm thick, coupled to a CMOS readout application specific integrated circuit (ASIC). The first synchrotron X-ray characterization of this detector is presented, and its ability to selectively count individual X-rays within two independent arrival time windows, a programmable energy range, and localized to a single pixel is demonstrated. During our first trial run at Argonne National Laboratory's Advance Photon Source, the detector achieved a 60 ns gating time and 700 eV full width at half-maximum energy resolution in agreement with design parameters. Each pixel of the PAD holds two independent digital counters, and the discriminator for X-ray energy features both an upper and lower threshold to window the energy of interest discarding unwanted background. This smart-pixel technology allows energy and time resolution to be set and optimized in software. It is found that the detector linearity follows an isolated dead-time model, implying that megahertz count rates should be possible in each pixel. Measurement of the line and point spread functions showed negligible spatial blurring. When combined with the timing structure of the synchrotron storage ring, it is demonstrated that the area detector can perform both picosecond time-resolved X-ray diffraction and fluorescence spectroscopy measurements.

Arraycount, an algorithm for automatic cell counting in microwell arrays.

PubMed

Kachouie, Nezamoddin; Kang, Lifeng; Khademhosseini, Ali

2009-09-01

Microscale technologies have emerged as a powerful tool for studying and manipulating biological systems and miniaturizing experiments. However, the lack of software complementing these techniques has made it difficult to apply them for many high-throughput experiments. This work establishes Arraycount, an approach to automatically count cells in microwell arrays. The procedure consists of fluorescent microscope imaging of cells that are seeded in microwells of a microarray system and then analyzing images via computer to recognize the array and count cells inside each microwell. To start counting, green and red fluorescent images (representing live and dead cells, respectively) are extracted from the original image and processed separately. A template-matching algorithm is proposed in which pre-defined well and cell templates are matched against the red and green images to locate microwells and cells. Subsequently, local maxima in the correlation maps are determined and local maxima maps are thresholded. At the end, the software records the cell counts for each detected microwell on the original image in high-throughput. The automated counting was shown to be accurate compared with manual counting, with a difference of approximately 1-2 cells per microwell: based on cell concentration, the absolute difference between manual and automatic counting measurements was 2.5-13%.

Half-life of 51Mn

NASA Astrophysics Data System (ADS)

Graves, Stephen A.; Ellison, Paul A.; Valdovinos, Hector F.; Barnhart, Todd E.; Nickles, Robert J.; Engle, Jonathan W.

2017-07-01

The half-life of 51Mn was measured by serial gamma spectrometry of the 511-keV annihilation photon following decay by β+ emission. Data were collected every 100 seconds for 100,000-230,000 seconds within each measurement (n =4 ). The 511-keV incidence rate was calculated from the 511-keV spectral peak area and count duration, corrected for detector dead time and radioactive decay. Least-squares regression analysis was used to determine the half-life of 51Mn while accounting for the presence of background contaminants, notably 55Co. The result was 45.59 ±0.07 min, which is the highest precision measurement to date and disagrees with the current Nuclear Data Sheets value by over 6 σ .

Feasibility of a high-speed gamma-camera design using the high-yield-pileup-event-recovery method.

PubMed

Wong, W H; Li, H; Uribe, J; Baghaei, H; Wang, Y; Yokoyama, S

2001-04-01

Higher count-rate gamma cameras than are currently used are needed if the technology is to fulfill its promise in positron coincidence imaging, radionuclide therapy dosimetry imaging, and cardiac first-pass imaging. The present single-crystal design coupled with conventional detector electronics and the traditional Anger-positioning algorithm hinder higher count-rate imaging because of the pileup of gamma-ray signals in the detector and electronics. At an interaction rate of 2 million events per second, the fraction of nonpileup events is < 20% of the total incident events. Hence, the recovery of pileup events can significantly increase the count-rate capability, increase the yield of imaging photons, and minimize image artifacts associated with pileups. A new technology to significantly enhance the performance of gamma cameras in this area is introduced. We introduce a new electronic design called high-yield-pileup-event-recovery (HYPER) electronics for processing the detector signal in gamma cameras so that the individual gamma energies and positions of pileup events, including multiple pileups, can be resolved and recovered despite the mixing of signals. To illustrate the feasibility of the design concept, we have developed a small gamma-camera prototype with the HYPER-Anger electronics. The camera has a 10 x 10 x 1 cm NaI(Tl) crystal with four photomultipliers. Hot-spot and line sources with very high 99mTc activities were imaged. The phantoms were imaged continuously from 60,000 to 3,500,000 counts per second to illustrate the efficacy of the method as a function of counting rates. At 2-3 million events per second, all phantoms were imaged with little distortion, pileup, and dead-time loss. At these counting rates, multiple pileup events (> or = 3 events piling together) were the predominate occurrences, and the HYPER circuit functioned well to resolve and recover these events. The full width at half maximum of the line-spread function at 3,000,000 counts per second was 1.6 times that at 60,000 counts per second. This feasibility study showed that the HYPER electronic concept works; it can significantly increase the count-rate capability and dose efficiency of gamma cameras. In a larger clinical camera, multiple HYPER-Anger circuits may be implemented to further improve the imaging counting rates that we have shown by multiple times. This technology would facilitate the use of gamma cameras for radionuclide therapy dosimetry imaging, cardiac first-pass imaging, and positron coincidence imaging and the simultaneous acquisition of transmission and emission data using different isotopes with less cross-contamination between transmission and emission data.

NATALIE: A 32 detector integrated acquisition system to characterize laser produced energetic particles with nuclear techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tarisien, M.; Plaisir, C.; Gobet, F.

2011-02-15

We present a stand-alone system to characterize the high-energy particles emitted in the interaction of ultrahigh intensity laser pulses with matter. According to the laser and target characteristics, electrons or protons are produced with energies higher than a few mega electron volts. Selected material samples can, therefore, be activated via nuclear reactions. A multidetector, named NATALIE, has been developed to count the {beta}{sup +} activity of these irradiated samples. The coincidence technique used, designed in an integrated system, results in very low background in the data, which is required for low activity measurements. It, therefore, allows a good precision onmore » the nuclear activation yields of the produced radionuclides. The system allows high counting rates and online correction of the dead time. It also provides, online, a quick control of the experiment. Geant4 simulations are used at different steps of the data analysis to deduce, from the measured activities, the energy and angular distributions of the laser-induced particle beams. Two applications are presented to illustrate the characterization of electrons and protons.« less

Fully Integrated Linear Single Photon Avalanche Diode (SPAD) Array with Parallel Readout Circuit in a Standard 180 nm CMOS Process

NASA Astrophysics Data System (ADS)

Isaak, S.; Bull, S.; Pitter, M. C.; Harrison, Ian.

2011-05-01

This paper reports on the development of a SPAD device and its subsequent use in an actively quenched single photon counting imaging system, and was fabricated in a UMC 0.18 μm CMOS process. A low-doped p- guard ring (t-well layer) encircling the active area to prevent the premature reverse breakdown. The array is a 16×1 parallel output SPAD array, which comprises of an active quenched SPAD circuit in each pixel with the current value being set by an external resistor RRef = 300 kΩ. The SPAD I-V response, ID was found to slowly increase until VBD was reached at excess bias voltage, Ve = 11.03 V, and then rapidly increase due to avalanche multiplication. Digital circuitry to control the SPAD array and perform the necessary data processing was designed in VHDL and implemented on a FPGA chip. At room temperature, the dark count was found to be approximately 13 KHz for most of the 16 SPAD pixels and the dead time was estimated to be 40 ns.

High speed superconducting nanowire single-photon detector with nine interleaved nanowires

NASA Astrophysics Data System (ADS)

Huang, Jia; Zhang, Weijun; You, Lixing; Zhang, Chengjun; Lv, Chaolin; Wang, Yong; Liu, Xiaoyu; Li, Hao; Wang, Zhen

2018-07-01

Count rate (CR) is one of the key parameters of superconducting nanowire single-photon detectors (SNSPDs). The practical SNSPDs usually have a CR of a few MHz to a few tens of MHz owing to the large kinetic inductance originating from the long nanowire, which is necessary for effectively coupling the photons. A feasible approach to decrease the kinetic inductance and consequently increase the detection speed is to replace a long single nanowire with multiple individual nanowires in an array. In this study, we report an SNSPD of nine interleaved nanowires with 70% system detection efficiency (SDE) and 200 Hz dark count rate at the low-photon-flux limit of 1550 nm. Owing to the small dead time (<6 ns) of each nanowire, the SNSPD achieved a maximum CR of 0.93 GHz at a photon flux of 1.26 × 1010 photons s‑1 with an SDE of ∼7.4%, and a CR of 200 MHz with an SDE of over 50%. Furthermore, a photon number resolvability of up to nine photons was also demonstrated.

Reproductive indices in natural nests of giant Amazon river turtles Podocnemis expansa (Schweigger, 1812) (Testudines, Podocnemididae) in the Environmental Protection Area Meanders of the Araguaia River.

PubMed

Alves-Júnior, J R F; Lustosa, A P G; Bosso, A C S; Balestra, R A M; Bastos, L F; Miranda, L B; Santos, A L Q

2012-02-01

A count was made of unhatched eggs and hatchling live and dead Podocnemis expansa turtles in 327 natural nests located on the beaches of the Environmental Protection Area (EPA) Meanders of the Araguaia River, to determine the percentage of hatching (94.63%), non-hatching (5.37%), survival (94.24%) and hatchling mortality (5.76%), and the average percentage of dead hatchlings during the 15 days in the nursery (0.97%). The mean number of hatchlings per nest was determined from the sum of the number of live and dead hatchlings divided by the total number of nests, while the mean number of eggs per nest was determined from the sum of live and dead hatchlings and unhatched eggs divided by the number of nests. These calculations yielded the following mean values: live hatchlings (88.98 ± 23.94), dead hatchlings (0.37 ± 0.93), unhatched eggs (5.07 ± 9.57), and total number of eggs (94.42 ± 21.30). The reproductive efficiency of the wild population of P. expansa can be affected by many environmental factors such as temperature, humidity and rainfall. In addition, man-made factors like the presence of chemicals in the water and the potential for infectious disease also have significant impact. The reproductive indices data obtained from this study are indispensable for future investigations of hatching anomalies.

Correction for the detector-dead-time effect on the second-order correlation of stationary sub-Poissonian light in a two-detector configuration

NASA Astrophysics Data System (ADS)

Ann, Byoung-moo; Song, Younghoon; Kim, Junki; Yang, Daeho; An, Kyungwon

2015-08-01

Exact measurement of the second-order correlation function g(2 )(t ) of a light source is essential when investigating the photon statistics and the light generation process of the source. For a stationary single-mode light source, the Mandel Q factor is directly related to g(2 )(0 ) . For a large mean photon number in the mode, the deviation of g(2 )(0 ) from unity is so small that even a tiny error in measuring g(2 )(0 ) would result in an inaccurate Mandel Q . In this work, we address the detector-dead-time effect on g(2 )(0 ) of stationary sub-Poissonian light. It is then found that detector dead time can induce a serious error in g(2 )(0 ) and thus in Mandel Q in those cases even in a two-detector configuration. Utilizing the cavity-QED microlaser, a well-established sub-Poissonian light source, we measured g(2 )(0 ) with two different types of photodetectors with different dead times. We also introduced prolonged dead time by intentionally deleting the photodetection events following a preceding one within a specified time interval. We found that the observed Q of the cavity-QED microlaser was underestimated by 19% with respect to the dead-time-free Q when its mean photon number was about 600. We derived an analytic formula which well explains the behavior of the g(2 )(0 ) as a function of the dead time.

Influence of Asellus aquaticus on Escherichia coli, Klebsiella pneumoniae, Campylobacter jejuni and naturally occurring heterotrophic bacteria in drinking water.

PubMed

Christensen, Sarah C B; Nissen, Erling; Arvin, Erik; Albrechtsen, Hans-Jørgen

2012-10-15

Water lice, Asellus aquaticus (isopoda), frequently occur in drinking water distribution systems where they are a nuisance to consumers and water utilities. Whether they are solely an aesthetic problem or also affect the microbial water quality is a matter of interest. We studied the influence of A. aquaticus on microbial water quality in non-chlorinated drinking water in controlled laboratory experiments. Pure cultures of the indicator organisms Escherichia coli and Klebsiella pneumoniae and the pathogen Campylobacter jejuni as well as naturally occurring heterotrophic drinking water bacteria (measured as heterotrophic plate counts, HPC) were investigated in microcosms at 7 °C, containing non-sterilised drinking water, drinking water sediment and A. aquaticus collected from a non-chlorinated ground water based drinking water supply system. Concentrations of E. coli, K. pneumoniae and C. jejuni decreased over time, following a first order decay with half lives of 5.3, 18.4 and 1.3 days, respectively. A. aquaticus did not affect survival of indicators and pathogens substantially whereas HPC were influenced by presence of dead A. aquaticus. Growth rates increased with an average of 48% for bacteria grown on R-2A agar and an average of 83% for bacteria grown on yeast extract agar when dead A. aquaticus were present compared to no and living A. aquaticus present. A. aquaticus associated E. coli, K. pneumoniae and C. jejuni were measured (up to 25 per living and 500 per dead A. aquaticus) and so were A. aquaticus associated heterotrophic bacteria (>1.8*10(4) CFU per living and >6*10(4) CFU per dead A. aquaticus). A. aquaticus did not serve as an optimised habitat that increased survival of indicators and pathogens, since A. aquaticus associated E. coli, K. pneumoniae and C. jejuni were only measured as long as the bacteria were also present in the water and sediment. Copyright © 2012 Elsevier Ltd. All rights reserved.

24-hour evaluation of dental plaque bacteria and halitosis after consumption of a single placebo or dental treat by dogs.

PubMed

Jeusette, Isabelle C; Román, Aurora Mateo; Torre, Celina; Crusafont, Josep; Sánchez, Nuria; Sánchez, Maria C; Pérez-Salcedo, Leire; Herrera, David

2016-06-01

OBJECTIVE To determine whether consumption of a single dental treat with specific mechanical properties and active ingredients would provide a 24-hour effect on dental plaque bacteria and halitosis in dogs. ANIMALS 10 dogs of various breeds from a privately owned colony that had received routine dental scaling and polishing 4 weeks before the study began. PROCEDURES Dogs were randomly assigned to receive 1 placebo or dental treat first. A 4-week washout period was provided, and then dogs received the opposite treatment. Oral plaque and breath samples were collected before and 0.5, 3, 12, and 24 hours after treat consumption. Volatile sulfur compounds (VSCs) concentration was measured in breath samples. Total aerobic, total anaerobic, Porphyromonas gulae, Prevotella intermedia-like, Tannerella forsythia, and Fusobacterium nucleatum bacterial counts (measured via bacterial culture) and total live bacterial counts, total live and dead bacterial counts, and bacterial vitality (measured via quantitative real-time PCR assay) were assessed in plaque samples. RESULTS Compared with placebo treat consumption, dental treat consumption resulted in a significant decrease in breath VSCs concentration and all plaque bacterial counts, without an effect on bacterial vitality. Effects of the dental treat versus the placebo treat persisted for 12 hours for several bacterial counts and for 24 hours for breath VSCs concentration. CONCLUSIONS AND CLINICAL RELEVANCE Although clinical benefits should be investigated in larger scale, longer-term studies, results of this study suggested that feeding the evaluated dental treat may help to decrease oral bacterial growth in dogs for 12 hours and oral malodor for 24 hours. A feeding interval of 12 hours is therefore recommended.

Fully industrialised single photon avalanche diodes

NASA Astrophysics Data System (ADS)

Pellegrini, S.; Rae, B.

2017-05-01

Single Photon Avalanche diodes (SPADs) were first realized more than five decades ago[1][1], and have now been industrialized for mass production in the 130 nm CMOS technology node by STMicroelectronics (STM). In this paper we present the latest STM SPAD with an excellent NIR photon detection probability (>5% at 850nm), a dark count rate median of 100 cps at room temperature and a low breakdown voltage of 14.2V. The dead time of the SPAD is approximately 25 ns, leading to a maximum count rate of 40 Mcps. Thanks to the 130 nm gate length of the CMOS technology used and the associated high digital gate density, complex digital signal processing can be implemented allowing fully integrated systems to be realized. The low bias required by the SPAD makes it possible for voltage generation to be achieved on-chip (e.g. charge pumped). We introduce our first generation time-of-flight system (VL6180) based on the STM SPAD technology, which is capable of ranging up to 60 cm in 60 ms. Ranging capabilities and accuracy are measured using a set of moving targets with reflectance of 5%, 17% and 88% in a fully automated test bed. To the best of our knowledge this was the first high volume SPAD-based device. To our knowledge this is the first time details of SPAD performance over production volumes and lifetime have been presented.

Smith predictor-based multiple periodic disturbance compensation for long dead-time processes

NASA Astrophysics Data System (ADS)

Tan, Fang; Li, Han-Xiong; Shen, Ping

2018-05-01

Many disturbance rejection methods have been proposed for processes with dead-time, while these existing methods may not work well under multiple periodic disturbances. In this paper, a multiple periodic disturbance rejection is proposed under the Smith predictor configuration for processes with long dead-time. One feedback loop is added to compensate periodic disturbance while retaining the advantage of the Smith predictor. With information of the disturbance spectrum, the added feedback loop can remove multiple periodic disturbances effectively. The robust stability can be easily maintained through the rigorous analysis. Finally, simulation examples demonstrate the effectiveness and robustness of the proposed method for processes with long dead-time.

Dealing with the health state 'dead' when using discrete choice experiments to obtain values for EQ-5D-5L heath states.

PubMed

Ramos-Goñi, Juan Manuel; Rivero-Arias, Oliver; Errea, María; Stolk, Elly A; Herdman, Michael; Cabasés, Juan Manuel

2013-07-01

To evaluate two different methods to obtain a dead (0)--full health (1) scale for EQ-5D-5L valuation studies when using discrete choice (DC) modeling. The study was carried out among 400 respondents from Barcelona who were representative of the Spanish population in terms of age, sex, and level of education. The DC design included 50 pairs of health states in five blocks. Participants were forced to choose between two EQ-5D-5L states (A and B). Two extra questions concerned whether A and B were considered worse than dead. Each participant performed ten choice exercises. In addition, values were collected using lead-time trade-off (lead-time TTO), for which 100 states in ten blocks were selected. Each participant performed five lead-time TTO exercises. These consisted of DC models offering the health state 'dead' as one of the choices--for which all participants' responses were used (DCdead)--and a model that included only the responses of participants who chose at least one state as worse than dead (WTD) (DCWTD). The study also estimated DC models rescaled with lead-time TTO data and a lead-time TTO linear model. The DC(dead) and DCWTD models produced relatively similar results, although the coefficients in the DCdead model were slightly lower. The DC model rescaled with lead-time TTO data produced higher utility decrements. Lead-time TTO produced the highest utility decrements. The incorporation of the state 'dead' in the DC models produces results in concordance with DC models that do not include 'dead'.

Factors affecting ultraviolet-A photon emission from β-irradiated human keratinocyte cells.

PubMed

Le, M; Mothersill, C E; Seymour, C B; Ahmad, S B; Armstrong, A; Rainbow, A J; McNeill, F E

2015-08-21

The luminescence intensity of 340±5 nm photons emitted from HaCaT (human keratinocyte) cells was investigated using a single-photon-counting system during cellular exposure to (90)Y β-particles. Multiple factors were assessed to determine their influence upon the quantity and pattern of photon emission from β-irradiated cells. Exposure of 1 x 10(4) cells/5 mL to 703 μCi resulted in maximum UVA photoemission at 44.8 x 10(3)±2.5 x 10(3) counts per second (cps) from live HaCaT cells (background: 1-5 cps); a 16-fold increase above cell-free controls. Significant biophoton emission was achieved only upon stimulation and was also dependent upon presence of cells. UVA luminescence was measured for (90)Y activities 14 to 703 μCi where a positive relationship between photoemission and (90)Y activity was observed. Irradiation of live HaCaT cells plated at various densities produced a distinct pattern of emission whereby luminescence increased up to a maximum at 1 x 10(4) cells/5 mL and thereafter decreased. However, this result was not observed in the dead cell population. Both live and dead HaCaT cells were irradiated and were found to demonstrate different rates of photon emission at low β activities (⩽400 μCi). Dead cells exhibited greater photon emission rates than live cells which may be attributable to metabolic processes taking place to modulate the photoemissive effect. The results indicate that photon emission from HaCaT cells is perturbed by external stimulation, is dependent upon the activity of radiation delivered, the density of irradiated cells, and cell viability. It is postulated that biophoton emission may be modulated by a biological or metabolic process.

Assessment of bacterial endospore viability with fluorescent dyes.

PubMed

Laflamme, C; Lavigne, S; Ho, J; Duchaine, C

2004-01-01

To validate three fluorescence viability assays designed primarily for vegetative cells on pure Bacillus endospores. Purified fresh and gamma-irradiated Bacillus endospores (Bacillus cereus, B. coagulans and two strains of B. subtilis) were used. The viability assays were: 5-cyano-2,3-diotolyl tetrazolium chloride (CTC) to test respiratory activity and early germination, DiBAC4(3) and Live/Dead BacLight to measure membrane energization and permeabilization, respectively. Gamma irradiation treatment completely eliminated spore culturability and was used as negative control. The untreated spores showed respiratory activity after 1 h of incubation and this was characteristic of almost 100% of spores after 24 h. The membrane potential assessment gave no answer about spore viability. A lower proportion of untreated spores had permeabilized membrane compared with gamma-irradiated spores using Live/Dead BacLight (P < 0.02). It is possible to use CTC and Live/Dead BacLight to rapidly test endospore viability and evaluate the proportion of spores in a preparation that could not be recovered with plate count. This study shows that fluorescence tests could be applied to assess viability in potentially pathogenic Bacillus spore preparations within 1 h.

International Humanitarian Law: The legal framework for humanitarian forensic action.

PubMed

Gaggioli, Gloria

2018-01-01

In armed conflicts, death is not an exceptional occurrence, but becomes the rule and occurs on a daily basis. Dead bodies are sometimes despoiled, mutilated, abandoned without any funeral rite and without a decent burial. Unidentified remains may be counted by hundreds or thousands. As a result, families look for years for missing relatives, ignorant of the fate of their loved ones. International Humanitarian Law, also called the laws of war or the law of armed conflict, is an international law branch, which has been developed to regulate and, as far as possible, to humanize armed conflicts. It contains a number of clear and concrete obligations incumbent to belligerent parties on the management of dead bodies, which provide the legal framework for humanitarian forensic action. The purpose of this article is to present, in a simple and concise manner, these rules with a view to extrapolate some key legal principles, such as the obligation to respect the dignity of the dead or the right to know the fate of relatives, which shall guide anyone dealing with human remains. Copyright © 2017 Elsevier B.V. All rights reserved.

Can dead bacterial cells be defined and are genes expressed after cell death?

PubMed

Trevors, J T

2012-07-01

There is a paucity of knowledge on gene expression in dead bacterial cells. Why would this knowledge be useful? The cells are dead. However, the time duration of gene expression following cell death is often unknown, and possibly in the order of minutes. In addition, it is a challenge to determine if bacterial cells are dead, or viable but non-culturable (VBNC), and what is an agreed upon correct definition of dead bacteria. Cells in the bacterial population or community may die at different rates or times and this complicates both the viability and gene expression analysis. In this article, the definition of dead bacterial cells is discussed and its significance in continued gene expression in cells following death. The definition of living and dead has implications for possible, completely, synthetic bacterial cells that may be capable of growth and division. Copyright © 2012 Elsevier B.V. All rights reserved.

Survival of Staphylococcus pseudintermedius in modified Romanowsky staining solutions.

PubMed

Misan, Angus; Chan, Wei Yee; Trott, Darren; Hill, Peter B

2017-08-01

Stains that are used regularly for patient-side diagnosis to rapidly identify bacterial and fungal infections could become contaminated by common pathogens, such as Staphylococcus pseudintermedius, during slide immersion. To determine whether the inoculation of S. pseudintermedius into modified Romanowsky type stains (Quick Dip ® ) results in viable bacterial contamination and whether this is influenced by the addition of organic debris (canine hair and skin). A clinical isolate of S. pseudintermedius was inoculated into clean and organically contaminated Quick Dip ® solutions (methanol fixative, eosin, methylene blue), and positive (broth) and negative (bleach) controls. Each solution was tested for the presence of viable bacteria by counting the number of colony forming units (CFU/mL) at various time points. Solutions also were examined under high power microscopy to count the number of visible bacteria at each time point. Staphylococcus pseudintermedius was able to survive in the clean and contaminated Quick Dip ® stains for at least one hour, but by 24 h no viable bacteria remained. Survival of the bacteria was not supported in the fixative at any time point. Staphylococcus pseudintermedius remained visible under high power microscopy for up to 2 weeks in all organically contaminated solutions of the Quick Dip ® set. Staphylococcus pseudintermedius only remains viable in eosin and methylene blue for short periods of time, but the prolonged visibility of dead organisms could theoretically lead to the misdiagnosis of cytology samples. © 2017 ESVD and ACVD.

24 CFR 3280.401 - Structural load tests.

Code of Federal Regulations, 2013 CFR

2013-04-01

... sustaining its dead load plus superimposed live loads equal to 1.75 times the required live loads for a... in 1/4 design live load increments at 10-minute intervals until 1.25 times design live load plus dead... load plus dead load has been reached. Assembly failure shall be considered as design live load...

76 FR 63341 - Culturally Significant Objects Imported for Exhibition Determinations: “The Dead Sea Scrolls...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-12

... DEPARTMENT OF STATE [Public Notice 7644] Culturally Significant Objects Imported for Exhibition Determinations: ``The Dead Sea Scrolls: Life and Faith in Biblical Times'' SUMMARY: Notice is hereby given of the... exhibition ``The Dead Sea Scrolls: Life and Faith in Biblical Times'' imported from abroad for temporary...

24 CFR 3280.401 - Structural load tests.

Code of Federal Regulations, 2010 CFR

2010-04-01

... sustaining its dead load plus superimposed live loads equal to 1.75 times the required live loads for a... in 1/4 design live load increments at 10-minute intervals until 1.25 times design live load plus dead... load plus dead load has been reached. Assembly failure shall be considered as design live load...

24 CFR 3280.401 - Structural load tests.

Code of Federal Regulations, 2014 CFR

2014-04-01

... sustaining its dead load plus superimposed live loads equal to 1.75 times the required live loads for a... in 1/4 design live load increments at 10-minute intervals until 1.25 times design live load plus dead... load plus dead load has been reached. Assembly failure shall be considered as design live load...

24 CFR 3280.401 - Structural load tests.

Code of Federal Regulations, 2012 CFR

2012-04-01

... sustaining its dead load plus superimposed live loads equal to 1.75 times the required live loads for a... in 1/4 design live load increments at 10-minute intervals until 1.25 times design live load plus dead... load plus dead load has been reached. Assembly failure shall be considered as design live load...

24 CFR 3280.401 - Structural load tests.

Code of Federal Regulations, 2011 CFR

2011-04-01

... sustaining its dead load plus superimposed live loads equal to 1.75 times the required live loads for a... in 1/4 design live load increments at 10-minute intervals until 1.25 times design live load plus dead... load plus dead load has been reached. Assembly failure shall be considered as design live load...

Delay time correction of the gas analyzer in the calculation of anatomical dead space of the lung.

PubMed

Okubo, T; Shibata, H; Takishima, T

1983-07-01

By means of a mathematical model, we have studied a way to correct the delay time of the gas analyzer in order to calculate the anatomical dead space using Fowler's graphical method. The mathematical model was constructed of ten tubes of equal diameter but unequal length, so that the amount of dead space varied from tube to tube; the tubes were emptied sequentially. The gas analyzer responds with a time lag from the input of the gas signal to the beginning of the response, followed by an exponential response output. The single breath expired volume-concentration relationship was examined with three types of expired flow patterns of which were constant, exponential and sinusoidal. The results indicate that the time correction by the lag time plus time constant of the exponential response of the gas analyzer gives an accurate estimation of anatomical dead space. Time correction less inclusive than this, e.g. lag time only or lag time plus 50% response time, gives an overestimation, and a correction larger than this results in underestimation. The magnitude of error is dependent on the flow pattern and flow rate. The time correction in this study is only for the calculation of dead space, as the corrected volume-concentration curves does not coincide with the true curve. Such correction of the output of the gas analyzer is extremely important when one needs to compare the dead spaces of different gas species at a rather faster flow rate.

Deciphering The Fall And Rise Of The Dead Sea In Relation To Solar Forcing

NASA Astrophysics Data System (ADS)

Yousef, Shahinaz M.

2005-03-01

Solar Forcing on closed seas and Lakes is space time dependent. The Cipher of the Dead Sea level variation since 1200 BC is solved in the context of millenium and Wolf-Gleissberg solar cycles time scales. It is found that the pattern of Dead Sea level variation follows the pattern of major millenium solar cycles. The 70 m rise of Dead Sea around 1AD is due to the forcing of the maximum millenium major solar cycle. Although the pattern of the Dead Sea level variation is almost identical to major solar cycles pattern between 1100 and 1980 AD, there is a dating problem of the Dead Sea time series around 1100-1300 AD that time. A discrepancy that should be corrected for the solar and Dead Sea series to fit. Detailed level variations of the Dead Sea level for the past 200 years are solved in terms of the 80-120 years solar Wolf-Gliessberg magnetic cycles. Solar induced climate changes do happen at the turning points of those cycles. Those end-start and maximum turning points are coincident with the change in the solar rotation rate due to the presence of weak solar cycles. Such weak cycles occur in series of few cycles between the end and start of those Wolf-Gleissberg cycles. Another one or two weak r solar cycle occur following the maximum of those Wolf-Gleissberg cycles. Weak cycles induce drop in the energy budget emitted from the sun and reaching the Earth thus causing solar induced climate change. An 8 meter sudden rise of Dead Sea occur prior 1900 AD due to positive solar forcing of the second cycle of the weak cycles series on the Dead Sea. The same second weak cycle induced negative solar forcing on Lake Chad. The first weak solar cycle forced Lake Victoria to rise abruptly in 1878. The maximum turning point of the solar Wolf-Gleissberg cycle induced negative forcing on both the Aral Sea and the Dead Sea causing their shrinkage to an alarming reduced area ever since. On the other hand, few years delayed positive forcing caused Lake Chad and the Equatorial African lakes to rise abruptly by several meters. Since the present solar cycle number 23 is the first weak cycle of a series, and since it caused 1.6 m sharp rise in Lake Victoria in 1997, then there is a high probability that the Dead Sea will rise by the beginning of the second weak cycle in few years time. And since both the Aral Sea and the Dead Sea are very much in coherence since the late 1950s, then it is rather likely that the Aral Sea will rise with God's wish in the near future. However it is also demanded that Israel should allow more water of the Jordan River to feed the Dead Sea before its real death. Plans for joining the Dead sea to the Red and or to the Mediterranean Seas should be cancelled owing the damaging harm it will cause the Dead Sea as a perfect indicator of solar induced climate change on one hand. On the other hand, the Dead Sea time series always show abrupt changes that can be as high as 70 m; if we add to this a planned artificial rise of the Dead Sea to its level of the thirties, then a damaging flooding effect will ruin the establishments and environment greatly.

Evaluating the Toxicity/Fixation Balance for Corneal Cross-Linking With Sodium Hydroxymethylglycinate (SMG) and Riboflavin-UVA (CXL) in an Ex Vivo Rabbit Model Using Confocal Laser Scanning Fluorescence Microscopy.

PubMed

Kim, Su-Young; Babar, Natasha; Munteanu, Emilia Laura; Takaoka, Anna; Zyablitskaya, Mariya; Nagasaki, Takayuki; Trokel, Stephen L; Paik, David C

2016-04-01

To develop methods to delineate the relationship between endothelial cell toxicity and tissue fixation (toxicity/fixation) using sodium hydroxymethylglycinate (SMG), a formaldehyde releaser, and riboflavin-UVA photochemical corneal cross-linking (CXL) for therapeutic tissue cross-linking of the cornea. Eleven fresh cadaveric rabbit heads were used for ex vivo corneal cross-linking simulation. After epithelial debridement, the tissue was exposed to 1/4 max (9.8 mM) or 1/3 max (13 mM) SMG at pH 8.5 for 30 minutes or riboflavin-UVA (CXL). The contralateral cornea served as a paired control. Postexposure, cross-linking efficacy was determined by thermal denaturation temperature (Tm) and endothelial damage was assessed using calcein AM and ethidium homodimer staining (The Live/Dead Kit). Confocal laser scanning fluorescence microscopy was used to generate live/dead cell counts using a standardized algorithm. The ΔTm after CXL, 1/3 SMG, and 1/4 SMG was 2.2 ± 0.9°C, 1.3 ± 0.5°C, and 1.1 ± 0.5°C, respectively. Endothelial cell damage was expressed as the percent of dead cells/live + dead cells counted per high-power field. The values were 3 ± 1.7% (control) and 8.9 ± 11.1% (CXL) (P = 0.390); 1 ± 0.2% (control) and 19.5 ± 32.2% (1/3 max SMG) (P = 0.426); and 2.7 ± 2.4% (control) and 2.8 ± 2.2% (1/4 max SMG) (P = 0.938). The values for endothelial toxicity were then indexed over the shift in Tm to yield a toxicity/fixation index. The values were as follows: 2.7 for CXL, 14 for 1/3 max, and 0.1 for 1/4 max. Quarter max (1/4 max = 9.8 mM) SMG effectively cross-linked tissue and was nontoxic to endothelial cells. Thus, SMG is potentially a compound that could achieve both desired effects.

Counting the DEAD: Did the Dinosaurs and Their Contemporaries Die Out with a Bang or a Whimper?

ERIC Educational Resources Information Center

Monastersky, Richard

1992-01-01

Researchers who study the fossil record are seeking to determine whether the impact made by a comet or meteor really did decimate up to half of the life on this planet at the end of the Cretaceous period. Questions whether the extinction of plant and animal life was abrupt, started before the impact, or was a gradual change. (KR)

Examining the Impact of External Influences on Police Use of Deadly Force over Time.

ERIC Educational Resources Information Center

White, Michael D.

2002-01-01

Used interrupted time-series analysis (ARIMA) to study the impact of legislation and judicial intervention on the use of deadly force by police officers in Philadelphia, Pennsylvania. Findings generally suggest that dynamic changes in the internal working environment can outweigh the influence of external mechanisms on deadly force use. Findings…

Model-Based Dead Time Optimization for Voltage-Source Converters Utilizing Silicon Carbide Semiconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zheyu; Lu, Haifeng; Costinett, Daniel J.

Dead time significantly affects the reliability, power quality, and efficiency of voltage-source converters. For silicon carbide (SiC) devices, considering the high sensitivity of turn-off time to the operating conditions (> 5× difference between light load and full load) and characteristics of inductive loads (> 2× difference between motor load and inductor), as well as large additional energy loss induced by the freewheeling diode conduction during the superfluous dead time (~15% of the switching loss), then the traditional fixed dead time setting becomes inappropriate. This paper introduces an approach to adaptively regulate the dead time considering the current operating condition andmore » load characteristics via synthesizing online monitored turn-off switching parameters in the microcontroller with an embedded preset optimization model. Here, based on a buck converter built with 1200-V SiC MOSFETs, the experimental results show that the proposed method is able to ensure reliability and reduce power loss by 12% at full load and 18.2% at light load (8% of the full load in this case study).« less

Model-Based Dead Time Optimization for Voltage-Source Converters Utilizing Silicon Carbide Semiconductors

DOE PAGES

Zhang, Zheyu; Lu, Haifeng; Costinett, Daniel J.; ...

2016-12-29

Dead time significantly affects the reliability, power quality, and efficiency of voltage-source converters. For silicon carbide (SiC) devices, considering the high sensitivity of turn-off time to the operating conditions (> 5× difference between light load and full load) and characteristics of inductive loads (> 2× difference between motor load and inductor), as well as large additional energy loss induced by the freewheeling diode conduction during the superfluous dead time (~15% of the switching loss), then the traditional fixed dead time setting becomes inappropriate. This paper introduces an approach to adaptively regulate the dead time considering the current operating condition andmore » load characteristics via synthesizing online monitored turn-off switching parameters in the microcontroller with an embedded preset optimization model. Here, based on a buck converter built with 1200-V SiC MOSFETs, the experimental results show that the proposed method is able to ensure reliability and reduce power loss by 12% at full load and 18.2% at light load (8% of the full load in this case study).« less

A SPAD-based 3D imager with in-pixel TDC for 145ps-accuracy ToF measurement

NASA Astrophysics Data System (ADS)

Vornicu, I.; Carmona-Galán, R.; Rodríguez-Vázquez, Á.

2015-03-01

The design and measurements of a CMOS 64 × 64 Single-Photon Avalanche-Diode (SPAD) array with in-pixel Time-to-Digital Converter (TDC) are presented. This paper thoroughly describes the imager at architectural and circuit level with particular emphasis on the characterization of the SPAD-detector ensemble. It is aimed to 2D imaging and 3D image reconstruction in low light environments. It has been fabricated in a standard 0.18μm CMOS process, i. e. without high voltage or low noise features. In these circumstances, we are facing a high number of dark counts and low photon detection efficiency. Several techniques have been applied to ensure proper functionality, namely: i) time-gated SPAD front-end with fast active-quenching/recharge circuit featuring tunable dead-time, ii) reverse start-stop scheme, iii) programmable time resolution of the TDC based on a novel pseudo-differential voltage controlled ring oscillator with fast start-up, iv) a global calibration scheme against temperature and process variation. Measurements results of individual SPAD-TDC ensemble jitter, array uniformity and time resolution programmability are also provided.

Coding for Communication Channels with Dead-Time Constraints

NASA Technical Reports Server (NTRS)

Moision, Bruce; Hamkins, Jon

2004-01-01

Coding schemes have been designed and investigated specifically for optical and electronic data-communication channels in which information is conveyed via pulse-position modulation (PPM) subject to dead-time constraints. These schemes involve the use of error-correcting codes concatenated with codes denoted constrained codes. These codes are decoded using an interactive method. In pulse-position modulation, time is partitioned into frames of Mslots of equal duration. Each frame contains one pulsed slot (all others are non-pulsed). For a given channel, the dead-time constraints are defined as a maximum and a minimum on the allowable time between pulses. For example, if a Q-switched laser is used to transmit the pulses, then the minimum allowable dead time is the time needed to recharge the laser for the next pulse. In the case of bits recorded on a magnetic medium, the minimum allowable time between pulses depends on the recording/playback speed and the minimum distance between pulses needed to prevent interference between adjacent bits during readout. The maximum allowable dead time for a given channel is the maximum time for which it is possible to satisfy the requirement to synchronize slots. In mathematical shorthand, the dead-time constraints for a given channel are represented by the pair of integers (d,k), where d is the minimum allowable number of zeroes between ones and k is the maximum allowable number of zeroes between ones. A system of the type to which the present schemes apply is represented by a binary- input, real-valued-output channel model illustrated in the figure. At the transmitting end, information bits are first encoded by use of an error-correcting code, then further encoded by use of a constrained code. Several constrained codes for channels subject to constraints of (d,infinity) have been investigated theoretically and computationally. The baseline codes chosen for purposes of comparison were simple PPM codes characterized by M-slot PPM frames separated by d-slot dead times.

Dead-time Corrected Disdrometer Data

DOE Data Explorer

Bartholomew, Mary Jane

2008-03-05

Original and dead-time corrected disdrometer results for observations made at SGP and TWP. The correction is based on the technique discussed in Sheppard and Joe, 1994. In addition, these files contain calculated radar reflectivity factor, mean Doppler velocity and attenuation for every measurement for both the original and dead-time corrected data at the following wavelengths: 0.316, 0.856, 3.2, 5, and 10cm (W,K,X,C,S bands). Pavlos Kollias provided the code to do these calculations.

Characteristic of fermented spinach (Amaranthus spp.) polyphenol by kombucha culture for antioxidant compound

NASA Astrophysics Data System (ADS)

Aspiyanto, Susilowati, Agustine; Iskandar, Jeti M.; Melanie, Hakiki; Maryati, Yati; Lotulung, Puspa D.

2017-01-01

Fermentation on spinach (Amaranthus sp.) vegetable by kombucha culture as an effort to get poliphenol as antioxidant compound had been done. Purification of fermented spinach extract suspension was carried out through microfiltration (MF) membrane (pore size 0.15 µm) fitted in dead-end Stirred Ultrafiltration Cell (SUFC) mode at fixed condition (stirrer rotation 400 rpm, room temperature, pressure 40 psia). Result of the experimental activity showed that long fermentation time increased total acids, total polyphenol and Total Plate Count (TPC), and decreased total solids and reducing sugar in biomass. The optimal fermentation time was reached for 2 weeks with total polyphenol recovery increasing of 92.76 % from before and after fermentation. On this optimal fermentation time, biomass had identified galic acid with relative intensity of 8 %, while as polyphenol monomer was resulted 5 kinds of polyphenol compounds with total intensity 27.97 % and molecular weight (MW) 191.1736, 193.1871 and 194.2170 at T2.5, T2.86 and T3.86. Long fermentation time increased functional properties of polyphenol as antioxidant.

Evaluation of trypan blue stain in a haemocytometer for rapid detection of cerebrospinal fluid sterility in HIV patients with cryptococcal meningitis.

PubMed

Kwizera, Richard; Akampurira, Andrew; Kandole, Tadeo K; Nielsen, Kirsten; Kambugu, Andrew; Meya, David B; Boulware, David R; Rhein, Joshua

2017-08-22

Quantitative culture is the most common method to determine the fungal burden and sterility of cerebrospinal fluid (CSF) among persons with cryptococcal meningitis. A major drawback of cultures is a long turnaround-time. Recent evidence demonstrates that live and dead Cryptococcus yeasts can be distinguished using trypan blue staining. We hypothesized that trypan blue staining combined with haemocytometer counting may provide a rapid estimation of quantitative culture count and detection of CSF sterility. To test this, we evaluated 194 CSF specimens from 96 HIV-infected participants with cryptococcal meningitis in Kampala, Uganda. Cryptococcal meningitis was diagnosed by CSF cryptococcal antigen (CRAG). We stained CSF with trypan blue and quantified yeasts using a haemocytometer. We compared the haemocytometer readings versus quantitative Cryptococcus CSF cultures. Haemocytometer counting with trypan blue staining had a sensitivity of 98% (64/65), while CSF cultures had a sensitivity of 95% (62/65) with reference to CSF CRAG for diagnostic CSF specimens. For samples that were positive in both tests, the haemocytometer had higher readings compared to culture. For diagnostic specimens, the median of log 10 transformed counts were 5.59 (n = 64, IQR = 5.09 to 6.05) for haemocytometer and 4.98 (n = 62, IQR = 3.75 to 5.79) for culture; while the overall median counts were 5.35 (n = 189, IQR = 4.78-5.84) for haemocytometer and 3.99 (n = 151, IQR = 2.59-5.14) for cultures. The percentage agreement with culture sterility was 2.4% (1/42). Counts among non-sterile follow-up specimens had a median of 5.38 (n = 86, IQR = 4.74 to 6.03) for haemocytometer and 2.89 (n = 89, IQR = 2.11 to 4.38) for culture. At diagnosis, CSF quantitative cultures correlated with haemocytometer counts (R 2  = 0.59, P < 0.001). At 7-14 days, quantitative cultures did not correlate with haemocytometer counts (R 2  = 0.43, P = 0.4). Despite a positive correlation, the haemocytometer counts with trypan blue staining did not predict the outcome of quantitative cultures in patients receiving antifungal therapy.

Using palynology to re-assess the Dead Sea laminated sediments - Indeed varves?

NASA Astrophysics Data System (ADS)

Bookman, Revital; Lopez-Merino, Lourdes; Belmaker, Reuven; Eshel, Amram; Epshtein Epshtein, Valentina; Leroy, Suzanne

2017-04-01

Lacustrine laminated sediments are often varves representing annual rhythmic deposition. The Dead Sea high-stand laminated sections consist of mm-scale alternating detrital and authigenic aragonite laminae. Previous studies assumed these laminae were varves; detritus deposition during the winter and aragonite in the summer. These sequences were used for varve counting and chronology, however this assumption has never been robustly validated. Here, we report an examination of the seasonal deposition of detrital and aragonite couplets from two well-known Late Holocene laminated sections at the Ze'elim fan-delta using palynology and grain-size distribution analyses. These analyses are complemented by the study of contemporary flash-flood samples and multivariate statistical analysis. Because transport affects the pollen preservation state, well-preserved (mostly) air-borne transported pollen was analysed separately from badly-preserved pollen and fungal spores, which are more indicative of water transport and reworking from soils. Our results indicate that (i) both detrital and aragonite laminae were deposited during the rainy season; (ii) aragonite laminae have significantly lower reworked pollen and fungal spore concentrations than detrital and flash-flood samples; and (iii) detrital laminae are composed of recycling of local and distal sources, with coarser particles that were initially deposited in the Dead Sea watershed and later transported via run-off to the lake. The conclusions suggest that detrital and aragonite couplets in the Dead Sea laminated sediments are most likely not varves and that the laminae deposition is related to the occurrence of flash-flood events. Consequently, at least for the Holocene sequences, laminated sediments cannot be considered as varves and Quaternary laminated sequences should be re-evaluated. The Dead Sea Basin laminated sequences (as the ICDP Dead Sea Deep Drilling Project record) should be used for the reconstruction of palaeo-flash flood records that will have a significant impact on understanding the palaeo-hydrology of the DSB and its implication to high-resolution climatic interpretation.

Optimization of PET instrumentation for brain activation studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahlbom, M.; Cherry, S.R.; Hoffman, E.J.

By performing cerebral blood flow studies with positron emission tomography (PET), and comparing blood flow images of different states of activation, functional mapping of the brain is possible. The ability of current commercial instruments to perform such studies is investigated in this work, based on a comparison of noise equivalent count (NEC) rates. Differences in the NEC performance of the different scanners in conjunction with scanner design parameters, provide insights into the importance of block design (size, dead time, crystal thickness) and overall scanner design (sensitivity and scatter fraction) for optimizing data from activation studies. The newer scanners with removablemore » septa, operating with 3-D acquisition, have much higher sensitivity, but require new methodology for optimized operation. Only by administering multiple low doses (fractionation) of the flow tracer can the high sensitivity be utilized.« less

Optimization of single photon detection model based on GM-APD

NASA Astrophysics Data System (ADS)

Chen, Yu; Yang, Yi; Hao, Peiyu

2017-11-01

One hundred kilometers high precision laser ranging hopes the detector has very strong detection ability for very weak light. At present, Geiger-Mode of Avalanche Photodiode has more use. It has high sensitivity and high photoelectric conversion efficiency. Selecting and designing the detector parameters according to the system index is of great importance to the improvement of photon detection efficiency. Design optimization requires a good model. In this paper, we research the existing Poisson distribution model, and consider the important detector parameters of dark count rate, dead time, quantum efficiency and so on. We improve the optimization of detection model, select the appropriate parameters to achieve optimal photon detection efficiency. The simulation is carried out by using Matlab and compared with the actual test results. The rationality of the model is verified. It has certain reference value in engineering applications.

Two-degree-of-freedom fractional order-PID controllers design for fractional order processes with dead-time.

PubMed

Li, Mingjie; Zhou, Ping; Zhao, Zhicheng; Zhang, Jinggang

2016-03-01

Recently, fractional order (FO) processes with dead-time have attracted more and more attention of many researchers in control field, but FO-PID controllers design techniques available for the FO processes with dead-time suffer from lack of direct systematic approaches. In this paper, a simple design and parameters tuning approach of two-degree-of-freedom (2-DOF) FO-PID controller based on internal model control (IMC) is proposed for FO processes with dead-time, conventional one-degree-of-freedom control exhibited the shortcoming of coupling of robustness and dynamic response performance. 2-DOF control can overcome the above weakness which means it realizes decoupling of robustness and dynamic performance from each other. The adjustable parameter η2 of FO-PID controller is directly related to the robustness of closed-loop system, and the analytical expression is given between the maximum sensitivity specification Ms and parameters η2. In addition, according to the dynamic performance requirement of the practical system, the parameters η1 can also be selected easily. By approximating the dead-time term of the process model with the first-order Padé or Taylor series, the expressions for 2-DOF FO-PID controller parameters are derived for three classes of FO processes with dead-time. Moreover, compared with other methods, the proposed method is simple and easy to implement. Finally, the simulation results are given to illustrate the effectiveness of this method. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

75 FR 34064 - Manufactured Home Construction and Safety Standards, Test Procedures for Roof Trusses

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-16

... dead load, or to 1.75 times the uplift load, minus the dead load in the upright position. [See Figure... 1/32-inch. Dead load must be applied to the top and bottom chord, and live load must be applied to... procedure. (i) Dead load. Measure and record initial elevation of the truss or trusses in the test position...

Adaptive NN tracking control of uncertain nonlinear discrete-time systems with nonaffine dead-zone input.

PubMed

Liu, Yan-Jun; Tong, Shaocheng

2015-03-01

In the paper, an adaptive tracking control design is studied for a class of nonlinear discrete-time systems with dead-zone input. The considered systems are of the nonaffine pure-feedback form and the dead-zone input appears nonlinearly in the systems. The contributions of the paper are that: 1) it is for the first time to investigate the control problem for this class of discrete-time systems with dead-zone; 2) there are major difficulties for stabilizing such systems and in order to overcome the difficulties, the systems are transformed into an n-step-ahead predictor but nonaffine function is still existent; and 3) an adaptive compensative term is constructed to compensate for the parameters of the dead-zone. The neural networks are used to approximate the unknown functions in the transformed systems. Based on the Lyapunov theory, it is proven that all the signals in the closed-loop system are semi-globally uniformly ultimately bounded and the tracking error converges to a small neighborhood of zero. Two simulation examples are provided to verify the effectiveness of the control approach in the paper.

Testing of RPMI-1640 as a Nutrient Medium for Fresh Semilunar Valve Storage.

DTIC Science & Technology

1979-01-01

familiarization with cage life, canine distemper and hepatitis vaccinations, worming for internal parasites, and obtain one normal complete blood count. Atropine...human valves. If these results are similar to this canine study, a more realistic evaluation can be made as to whether the best tissue for heart valve...replacement is from live tissue of human allografts or dead tissue of procine xenografts. I SUMMARY The medium selected to store canine heart valves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldhaber, M.K.; Staub, S.L.; Tokuhata, G.K.

A study was conducted to determine whether the incidence of spontaneous abortion was greater than expected near the Three Mile Island (TMI) nuclear power plant during the months following the March 28, 1979 accident. All persons living within five miles of TMI were registered shortly after the accident, and information on pregnancy at the time of the accident was collected. After one year, all pregnancy cases were followed up and outcomes ascertained. Using the life table method, it was found that, given pregnancies after four completed weeks of gestation counting from the first day of the last menstrual period, themore » estimated incidence of spontaneous abortion (miscarriage before completion of 16 weeks of gestation) was 15.1 per cent for women pregnant at the time of the TMI accident. Combining spontaneous abortions and stillbirths (delivery of a dead fetus after 16 weeks of gestation), the estimated incidence was 16.1 per cent for pregnancies after four completed weeks of gestation. Both incidences are comparable to baseline studies of fetal loss.« less

Spontaneous abortions after the Three Mile Island nuclear accident: a life table analysis.

PubMed

Goldhaber, M K; Staub, S L; Tokuhata, G K

1983-07-01

A study was conducted to determine whether the incidence of spontaneous abortion was greater than expected near the Three Mile Island (TMI) nuclear power plant during the months following the March 28, 1979 accident. All persons living within five miles of TMI were registered shortly after the accident, and information on pregnancy at the time of the accident was collected. After one year, all pregnancy cases were followed up and outcomes ascertained. Using the life table method, it was found that, given pregnancies after four completed weeks of gestation counting from the first day of the last menstrual period, the estimated incidence of spontaneous abortion (miscarriage before completion of 16 weeks of gestation) was 15.1 per cent for women pregnant at the time of the TMI accident. Combining spontaneous abortions and stillbirths (delivery of a dead fetus after 16 weeks of gestation), the estimated incidence was 16.1 per cent for pregnancies after four completed weeks of gestation. Both incidences are comparable to baseline studies of fetal loss.

The use of multiple indices of physiological activity to access viability in chlorine disinfected Escherichia coli O157:H7

NASA Technical Reports Server (NTRS)

Lisle, J. T.; Pyle, B. H.; McFeters, G. A.

1999-01-01

A suite of fluorescent intracellular stains and probes was used, in conjunction with viable plate counts, to assess the effect of chlorine disinfection on membrane potential (rhodamine 123; Rh123 and bis-(1,3-dibutylbarbituric acid) trimethine oxonol; DiBAC4(3)), membrane integrity (LIVE/DEAD BacLight kit), respiratory activity (5-cyano-2,3-ditolyl tetrazolium chloride; CTC) and substrate responsiveness (direct viable counts; DVC) in the commensal pathogen Escherichia coli O157:H7. After a 5 min exposure to the disinfectant, physiological indices were affected in the following order: viable plate counts > substrate responsiveness > membrane potential > respiratory activity > membrane integrity. In situ assessment of physiological activity by examining multiple targets, as demonstrated in this study, permits a more comprehensive determination of the site and extent of injury in bacterial cells following sublethal disinfection with chlorine. This approach to assessing altered bacterial physiology has application in various fields where detection of stressed bacteria is of interest.

Detection of Only Viable Bacterial Spores Using a Live/Dead Indicator in Mixed Populations

NASA Technical Reports Server (NTRS)

Behar, Alberto E.; Stam, Christina N.; Smiley, Ronald

2013-01-01

This method uses a photoaffinity label that recognizes DNA and can be used to distinguish populations of bacterial cells from bacterial spores without the use of heat shocking during conventional culture, and live from dead bacterial spores using molecular-based methods. Biological validation of commercial sterility using traditional and alternative technologies remains challenging. Recovery of viable spores is cumbersome, as the process requires substantial incubation time, and the extended time to results limits the ability to quickly evaluate the efficacy of existing technologies. Nucleic acid amplification approaches such as PCR (polymerase chain reaction) have shown promise for improving time to detection for a wide range of applications. Recent real-time PCR methods are particularly promising, as these methods can be made at least semi-quantitative by correspondence to a standard curve. Nonetheless, PCR-based methods are rarely used for process validation, largely because the DNA from dead bacterial cells is highly stable and hence, DNA-based amplification methods fail to discriminate between live and inactivated microorganisms. Currently, no published method has been shown to effectively distinguish between live and dead bacterial spores. This technology uses a DNA binding photoaffinity label that can be used to distinguish between live and dead bacterial spores with detection limits ranging from 109 to 102 spores/mL. An environmental sample suspected of containing a mixture of live and dead vegetative cells and bacterial endospores is treated with a photoaffinity label. This step will eliminate any vegetative cells (live or dead) and dead endospores present in the sample. To further determine the bacterial spore viability, DNA is extracted from the spores and total population is quantified by real-time PCR. The current NASA standard assay takes 72 hours for results. Part of this procedure requires a heat shock step at 80 degC for 15 minutes before the sample can be plated. Using a photoaffinity label would remove this step from the current assay as the label readily penetrates both live and dead bacterial cells. Secondly, the photoaffinity label can only penetrate dead bacterial spores, leaving behind the viable spore population. This would allow for rapid bacterial spore detection in a matter of hours compared to the several days that it takes for the NASA standard assay.

A Unified Approach to Adaptive Neural Control for Nonlinear Discrete-Time Systems With Nonlinear Dead-Zone Input.

PubMed

Liu, Yan-Jun; Gao, Ying; Tong, Shaocheng; Chen, C L Philip

2016-01-01

In this paper, an effective adaptive control approach is constructed to stabilize a class of nonlinear discrete-time systems, which contain unknown functions, unknown dead-zone input, and unknown control direction. Different from linear dead zone, the dead zone, in this paper, is a kind of nonlinear dead zone. To overcome the noncausal problem, which leads to the control scheme infeasible, the systems can be transformed into a m -step-ahead predictor. Due to nonlinear dead-zone appearance, the transformed predictor still contains the nonaffine function. In addition, it is assumed that the gain function of dead-zone input and the control direction are unknown. These conditions bring about the difficulties and the complicacy in the controller design. Thus, the implicit function theorem is applied to deal with nonaffine dead-zone appearance, the problem caused by the unknown control direction can be resolved through applying the discrete Nussbaum gain, and the neural networks are used to approximate the unknown function. Based on the Lyapunov theory, all the signals of the resulting closed-loop system are proved to be semiglobal uniformly ultimately bounded. Moreover, the tracking error is proved to be regulated to a small neighborhood around zero. The feasibility of the proposed approach is demonstrated by a simulation example.

Modeling decay rates of dead wood in a neotropical forest.

PubMed

Hérault, Bruno; Beauchêne, Jacques; Muller, Félix; Wagner, Fabien; Baraloto, Christopher; Blanc, Lilian; Martin, Jean-Michel

2010-09-01

Variation of dead wood decay rates among tropical trees remains one source of uncertainty in global models of the carbon cycle. Taking advantage of a broad forest plot network surveyed for tree mortality over a 23-year period, we measured the remaining fraction of boles from 367 dead trees from 26 neotropical species widely varying in wood density (0.23-1.24 g cm(-3)) and tree circumference at death time (31.5-272.0 cm). We modeled decay rates within a Bayesian framework assuming a first order differential equation to model the decomposition process and tested for the effects of forest management (selective logging vs. unexploited), of mode of death (standing vs. downed) and of topographical levels (bottomlands vs. hillsides vs. hilltops) on wood decay rates. The general decay model predicts the observed remaining fraction of dead wood (R2 = 60%) with only two biological predictors: tree circumference at death time and wood specific density. Neither selective logging nor local topography had a differential effect on wood decay rates. Including the mode of death into the model revealed that standing dead trees decomposed faster than downed dead trees, but the gain of model accuracy remains rather marginal. Overall, these results suggest that the release of carbon from tropical dead trees to the atmosphere can be simply estimated using tree circumference at death time and wood density.

Influence of fuel injection timing and pressure on in-flame soot particles in an automotive-size diesel engine.

PubMed

Zhang, Renlin; Kook, Sanghoon

2014-07-15

The current understanding of soot particle morphology in diesel engines and their dependency on the fuel injection timing and pressure is limited to those sampled from the exhaust. In this study, a thermophoretic sampling and subsequent transmission electron microscope imaging were applied to the in-flame soot particles inside the cylinder of a working diesel engine for various fuel injection timings and pressures. The results show that the number count of soot particles per image decreases by more than 80% when the injection timing is retarded from -12 to -2 crank angle degrees after the top dead center. The late injection also results in over 90% reduction of the projection area of soot particles on the TEM image and the size of soot aggregates also become smaller. The primary particle size, however, is found to be insensitive to the variations in fuel injection timing. For injection pressure variations, both the size of primary particles and soot aggregates are found to decrease with increasing injection pressure, demonstrating the benefits of high injection velocity and momentum. Detailed analysis shows that the number count of soot particles per image increases with increasing injection pressure up to 130 MPa, primarily due to the increased small particle aggregates that are less than 40 nm in the radius of gyration. The fractal dimension shows an overall decrease with the increasing injection pressure. However, there is a case that the fractal dimension shows an unexpected increase between 100 and 130 MPa injection pressure. It is because the small aggregates with more compact and agglomerated structures outnumber the large aggregates with more stretched chain-like structures.

A new single-photon avalanche diode in 90nm standard CMOS technology.

PubMed

Karami, Mohammad Azim; Gersbach, Marek; Yoon, Hyung-June; Charbon, Edoardo

2010-10-11

We report on the first implementation of a single-photon avalanche diode (SPAD) in 90nm complementary metal oxide semiconductor (CMOS) technology. The detector features an octagonal multiplication region and a guard ring to prevent premature edge breakdown using a standard mask set exclusively. The proposed structure emerged from a systematic study aimed at miniaturization, while optimizing overall performance. The guard ring design is the result of an extensive modeling effort aimed at constraining the multiplication region within a well-defined area where the electric field exceeds the critical value for impact ionization. The device exhibits a dark count rate of 8.1 kHz, a maximum photon detection probability of 9% and the jitter of 398ps at a wavelength of 637nm, all of them measured at room temperature and 0.13V of excess bias voltage. An afterpulsing probability of 32% is achieved at the nominal dead time. Applications include time-of-flight 3D vision, fluorescence lifetime imaging microscopy, fluorescence correlation spectroscopy, and time-resolved gamma/X-ray imaging. Standard characterization of the SPAD was performed in different bias voltages and temperatures.

The ICDP Dead Sea deep drill cores: records of climate change and tectonics in the Levant

NASA Astrophysics Data System (ADS)

Goldstein, S. L.; Stein, M.; Ben-Avraham, Z.; Agnon, A.; Ariztegui, D.; Brauer, A.; Haug, G. H.; Ito, E.; Kitagawa, H.; Torfstein, A.

2012-12-01

The Dead Sea drainage basin sits at the boundary of the Mediterranean and the Saharan climate zones, and the basin is formed by the Dead Sea transform fault. The ICDP-funded Dead Sea Deep Drilling Project recovered the longest and most complete paleo-environmental and paleo-seismic record in the Middle East, drilling holes of ~450 and ~350 meters in deep (~300 m below the lake level) and shallow sites (~3 m), respectively, and. The sediments record the evolving environmental conditions (e.g. droughts, rains, floods, dust-storms), as well as tectonics (earthquake layers). The core can be dated using 14C on organic materials, U-Th on inorganic aragonite, stable isotopes, and layer counting. They were opened, described, and XRF-scanned during June to November 2011, the first sampling party took place in July 2012, and study is now underway. Some important conclusions can already be drawn. The stratigraphy reflects the climate conditions. During wet climate intervals the lithology is typically varve-like laminated aragonite and detritus (aad), reflecting summer and winter seasons, respectively, and sequences of mud. Gypsum layers reflect more arid climate, and salt (halite) indicates extreme aridity. The Dead Sea expands during glacials, and the portion of the core that corresponds to the last glacial Lisan Formation above the shoreline is easily recognized in the core based on the common lithological sequence, and this allows us to infer a broad scale age model. Interglacials show all the lithologic facies (aad, mud, gypsum, salt), reflecting extreme climate variability, while glacials contain the aad, mud, and gypsum but lack salt layers. Thus we estimate that the deep site hole extends into MIS 7 (to ~200,000 years). Thin (up to several cm thick) seismic layers occur throughout the core, but thick (up to several meters) landslide deposits only occur during glacial intervals. The most dramatic discovery is evidence of an extreme dry interval during MIS 5 at the deep site. There is a ~40 cm thick interval of partly rounded pebbles in the core at ~235 m below the lake floor. It is the only clean pebbly unit in the core, and resembles a beach deposit. Below the layer there is ~45 meters of mainly salt. These observations indicate a severe dry interval during MIS 5. This observation has implications for the Middle East today, where the Dead Sea level is dropping at rates >1m/year, as all the countries in the area are using all the runoff. GCM models indicate a more arid future in the region. The core shows that the runoff nearly stopped during the last interglacial without human intervention. Dating is underway to constrain the timing of the extreme drydown.

Inhomogeneous Poisson process rate function inference from dead-time limited observations.

PubMed

Verma, Gunjan; Drost, Robert J

2017-05-01

The estimation of an inhomogeneous Poisson process (IHPP) rate function from a set of process observations is an important problem arising in optical communications and a variety of other applications. However, because of practical limitations of detector technology, one is often only able to observe a corrupted version of the original process. In this paper, we consider how inference of the rate function is affected by dead time, a period of time after the detection of an event during which a sensor is insensitive to subsequent IHPP events. We propose a flexible nonparametric Bayesian approach to infer an IHPP rate function given dead-time limited process realizations. Simulation results illustrate the effectiveness of our inference approach and suggest its ability to extend the utility of existing sensor technology by permitting more accurate inference on signals whose observations are dead-time limited. We apply our inference algorithm to experimentally collected optical communications data, demonstrating the practical utility of our approach in the context of channel modeling and validation.

Studies of ZVS soft switching of dual-active-bridge isolated bidirectional DC-DC converters

NASA Astrophysics Data System (ADS)

Xu, Fei; Zhao, Feng; Shi, Qibiao; Wen, Xuhui

2018-05-01

To operate dual-active-bridge isolated bidirectional dc- dc converter (DAB) at high efficiency, the two bridge switches must operate with Zero-Voltage-Switching (ZVS) over as wide an operating range as possible. This paper proposes a new perspective on realizing ZVS in dead-time. An exact theoretical analysis and mathematical mode is built to explain the process of ZVS switching in dead-time under Single Phase Shift (SPS) control strategy. In order to assure the two bridge switches operate on soft switching, every SPS switching point is analyzed. Generally, dead-time will be determined when the power electronic devices is selected. The key factor to realizing ZVS is the size of the end time of resonance comparing to dead-time. Through detailed analysis, it can obtain the conditions of all switches achieving ZVS turn-on and turn-off. Finally, simulation validates the theoretical analysis and some advice are given to realize the ZVS soft switching.

A rapid detection method using flow cytometry to monitor the risk of Legionella in bath water.

PubMed

Taguri, Toshitsugu; Oda, Yasunori; Sugiyama, Kanji; Nishikawa, Toru; Endo, Takuro; Izumiyama, Shinji; Yamazaki, Masayuki; Kura, Fumiaki

2011-07-01

Legionella species are the causative agents of human legionellosis, and bathing facilities have been identified as the sources of infection in several outbreaks in Japan. Researchers in Japan have recently reported evidence of significant associations between bacterial counts and the occurrence of Legionella in bathing facilities and in a hot tub model. A convenient and quantitative bacterial enumeration method is therefore required as an indicator of Legionella contamination or disinfection to replace existing methods such as time-consuming Legionella culture and expensive Legionella-DNA amplification. In this study, we developed a rapid detection method (RDM) to monitor the risk of Legionella using an automated microbial analyzing device based on flow cytometry techniques to measure the total number of bacteria in water samples within two minutes, by detecting typical patterns of scattered light and fluorescence. We first compared the results of our RDM with plate counting results for five filtered hot spring water samples spiked with three species of bacteria, including Legionella. Inactivation of these samples by chlorine was also assessed by the RDM, a live/dead bacterial fluorescence assay and plate counting. Using the RDM, the lower limit of quantitative bacterial counts in the spiked samples was determined as 3.0×10(3)(3.48log)counts mL(-1). We then used a laboratory model of a hot tub and found that the RDM could monitor the growth curve of naturally occurring heterotrophic bacteria with 1 and 2 days' delayed growth of amoeba and Legionella, respectively, and could also determine the killing curve of these bacteria by chlorination. Finally, samples with ≥3.48 or <3.48log total bacterial counts mL(-1) were tested using the RDM from 149 different hot tubs, and were found to be significantly associated with the positive or negative detection of Legionella with 95% sensitivity and 84% specificity. These findings indicated that the RDM can be used for Legionella control at bathing facilities, especially those where the effectiveness of chlorine is reduced by the presence of Fe(2+), Mn(2+), NH(4)(+), skin debris, and/or biofilms in the water. Copyright © 2011 Elsevier B.V. All rights reserved.

SU-E-I-20: Dead Time Count Loss Compensation in SPECT/CT: Projection Versus Global Correction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siman, W; Kappadath, S

Purpose: To compare projection-based versus global correction that compensate for deadtime count loss in SPECT/CT images. Methods: SPECT/CT images of an IEC phantom (2.3GBq 99mTc) with ∼10% deadtime loss containing the 37mm (uptake 3), 28 and 22mm (uptake 6) spheres were acquired using a 2 detector SPECT/CT system with 64 projections/detector and 15 s/projection. The deadtime, Ti and the true count rate, Ni at each projection, i was calculated using the monitor-source method. Deadtime corrected SPECT were reconstructed twice: (1) with projections that were individually-corrected for deadtime-losses; and (2) with original projections with losses and then correcting the reconstructed SPECTmore » images using a scaling factor equal to the inverse of the average fractional loss for 5 projections/detector. For both cases, the SPECT images were reconstructed using OSEM with attenuation and scatter corrections. The two SPECT datasets were assessed by comparing line profiles in xyplane and z-axis, evaluating the count recoveries, and comparing ROI statistics. Higher deadtime losses (up to 50%) were also simulated to the individually corrected projections by multiplying each projection i by exp(-a*Ni*Ti), where a is a scalar. Additionally, deadtime corrections in phantoms with different geometries and deadtime losses were also explored. The same two correction methods were carried for all these data sets. Results: Averaging the deadtime losses in 5 projections/detector suffices to recover >99% of the loss counts in most clinical cases. The line profiles (xyplane and z-axis) and the statistics in the ROIs drawn in the SPECT images corrected using both methods showed agreement within the statistical noise. The count-loss recoveries in the two methods also agree within >99%. Conclusion: The projection-based and the global correction yield visually indistinguishable SPECT images. The global correction based on sparse sampling of projections losses allows for accurate SPECT deadtime loss correction while keeping the study duration reasonable.« less

Dead wood biomass and turnover time, measured by radiocarbon, along a subalpine elevation gradient.

PubMed

Kueppers, Lara M; Southon, John; Baer, Paul; Harte, John

2004-12-01

Dead wood biomass can be a substantial fraction of stored carbon in forest ecosystems, and coarse woody debris (CWD) decay rates may be sensitive to climate warming. We used an elevation gradient in Colorado Rocky Mountain subalpine forest to examine climate and species effects on dead wood biomass, and on CWD decay rate. Using a new radiocarbon approach, we determined that the turnover time of lodgepole pine CWD (340+/-130 years) was roughly half as long in a site with 2.5-3 degrees C warmer air temperature, as that of pine (630+/-400 years) or Engelmann spruce CWD (800+/-960 and 650+/-410 years) in cooler sites. Across all sites and both species, CWD age ranged from 2 to 600 years, and turnover time was 580+/-180 years. Total standing and fallen dead wood biomass ranged from 4.7+/-0.2 to 54+/-1 Mg ha(-1), and from 2.8 to 60% of aboveground live tree biomass. Dead wood biomass increased 75 kg ha(-1) per meter gain in elevation and decreased 13 Mg ha(-1) for every degree C increase in mean air temperature. Differences in biomass and decay rates along the elevation gradient suggest that climate warming will lead to a loss of dead wood carbon from subalpine forest.

Characterizations of double pulsing in neutron multiplicity and coincidence counting systems

DOE PAGES

Koehler, Katrina E.; Henzl, Vladimir; Croft, Stephen; ...

2016-06-29

Passive neutron coincidence/multiplicity counters are subject to non-ideal behavior, such as double pulsing and dead time. It has been shown in the past that double-pulsing exhibits a distinct signature in a Rossi-alpha distribution, which is not readily noticed using traditional Multiplicity Shift Register analysis. But, it has been assumed that the use of a pre-delay in shift register analysis removes any effects of double pulsing. Here, we use high-fidelity simulations accompanied by experimental measurements to study the effects of double pulsing on multiplicity rates. By exploiting the information from the double pulsing signature peak observable in the Rossi-alpha distribution, themore » double pulsing fraction can be determined. Algebraic correction factors for the multiplicity rates in terms of the double pulsing fraction have been developed. We also discuss the role of these corrections across a range of scenarios.« less

Lessons to be learned: a case study approach. Unseasonal severe poisoning of two adults by deadly nightside (Atropa belladonna).

PubMed

Southgate, H J; Egerton, M; Dauncey, E A

2000-06-01

Unseasonal, mid-winter, severe poisoning by deadly nightshade is reported in two adults who simultaneously ate from a pie made of frozen deadly nightshade berries, mistaken at the time of picking for bilberries. Atropine levels are reported in the urine. Physostigmine treatment was ineffective.

Monte Carlo simulations versus experimental measurements in a small animal PET system. A comparison in the NEMA NU 4-2008 framework

NASA Astrophysics Data System (ADS)

Popota, F. D.; Aguiar, P.; España, S.; Lois, C.; Udias, J. M.; Ros, D.; Pavia, J.; Gispert, J. D.

2015-01-01

In this work a comparison between experimental and simulated data using GATE and PeneloPET Monte Carlo simulation packages is presented. All simulated setups, as well as the experimental measurements, followed exactly the guidelines of the NEMA NU 4-2008 standards using the microPET R4 scanner. The comparison was focused on spatial resolution, sensitivity, scatter fraction and counting rates performance. Both GATE and PeneloPET showed reasonable agreement for the spatial resolution when compared to experimental measurements, although they lead to slight underestimations for the points close to the edge. High accuracy was obtained between experiments and simulations of the system’s sensitivity and scatter fraction for an energy window of 350-650 keV, as well as for the counting rate simulations. The latter was the most complicated test to perform since each code demands different specifications for the characterization of the system’s dead time. Although simulated and experimental results were in excellent agreement for both simulation codes, PeneloPET demanded more information about the behavior of the real data acquisition system. To our knowledge, this constitutes the first validation of these Monte Carlo codes for the full NEMA NU 4-2008 standards for small animal PET imaging systems.

Monte Carlo simulations versus experimental measurements in a small animal PET system. A comparison in the NEMA NU 4-2008 framework.

PubMed

Popota, F D; Aguiar, P; España, S; Lois, C; Udias, J M; Ros, D; Pavia, J; Gispert, J D

2015-01-07

In this work a comparison between experimental and simulated data using GATE and PeneloPET Monte Carlo simulation packages is presented. All simulated setups, as well as the experimental measurements, followed exactly the guidelines of the NEMA NU 4-2008 standards using the microPET R4 scanner. The comparison was focused on spatial resolution, sensitivity, scatter fraction and counting rates performance. Both GATE and PeneloPET showed reasonable agreement for the spatial resolution when compared to experimental measurements, although they lead to slight underestimations for the points close to the edge. High accuracy was obtained between experiments and simulations of the system's sensitivity and scatter fraction for an energy window of 350-650 keV, as well as for the counting rate simulations. The latter was the most complicated test to perform since each code demands different specifications for the characterization of the system's dead time. Although simulated and experimental results were in excellent agreement for both simulation codes, PeneloPET demanded more information about the behavior of the real data acquisition system. To our knowledge, this constitutes the first validation of these Monte Carlo codes for the full NEMA NU 4-2008 standards for small animal PET imaging systems.

Scientific evidence of the therapeutic effects of dead sea treatments: a systematic review.

PubMed

Katz, Uriel; Shoenfeld, Yehuda; Zakin, Varda; Sherer, Yaniv; Sukenik, Shaul

2012-10-01

The Dead Sea, the deepest and most saline lake on earth, has been known from biblical times for its healing properties. The aim of this systematic review was to present critically the level of evidence for the claims of therapeutic effects of Dead Sea treatments in several rheumatologic diseases and psoriasis as well as to review these treatments' safety. All articles cited in MEDLINE under the query, "Dead Sea," were reviewed. We found bona fide evidence that Dead Sea treatments are especially effective in psoriasis due to both the special characteristics of solar ultraviolet radiation in the Dead Sea and the Dead Sea water balneotherapy. Dead Sea mud and Dead Sea balneotherapy have been found to be beneficial in rheumatologic diseases, including rheumatoid arthritis, psoriatic arthritis, ankylosing spondylitis, and knee osteoarthritis. In the safety analysis, we found no evidence for an increase in skin neoplasia, although skin actinic damage seems to be increased in patients treated in the Dead Sea. Dead Sea treatments do not lead to worsening of blood pressure. Substantial ingestion of Dead Sea water (generally in unusual near-drowning cases) is toxic and can result in cardiac rhythm disturbances because of electrolyte concentration abnormalities. Laboratory analysis of Dead Sea mud did not reveal mineral concentrations that could represent a health concern for their intended use. Dead Sea treatments are beneficial in several rheumatologic diseases and psoriasis and have a good safety profile. Copyright © 2012 Elsevier Inc. All rights reserved.

Impact of high 131I-activities on quantitative 124I-PET

NASA Astrophysics Data System (ADS)

Braad, P. E. N.; Hansen, S. B.; Høilund-Carlsen, P. F.

2015-07-01

Peri-therapeutic 124 I-PET/CT is of interest as guidance for radioiodine therapy. Unfortunately, image quality is complicated by dead time effects and increased random coincidence rates from high 131 I-activities. A series of phantom experiments with clinically relevant 124 I/131 I-activities were performed on a clinical PET/CT-system. Noise equivalent count rate (NECR) curves and quantitation accuracy were determined from repeated scans performed over several weeks on a decaying NEMA NU-2 1994 cylinder phantom initially filled with 25 MBq 124 I and 1250 MBq 131 I. Six spherical inserts with diameters 10-37 mm were filled with 124 I (0.45 MBq ml-1 ) and 131 I (22 MBq ml-1 ) and placed inside the background of the NEMA/IEC torso phantom. Contrast recovery, background variability and the accuracy of scatter and attenuation corrections were assessed at sphere-to-background activity ratios of 20, 10 and 5. Results were compared to pure 124 I-acquisitions. The quality of 124 I-PET images in the presence of high 131 I-activities was good and image quantification unaffected except at very high count rates. Quantitation accuracy and contrast recovery were uninfluenced at 131 I-activities below 1000 MBq, whereas image noise was slightly increased. The NECR peaked at 550 MBq of 131 I, where it was 2.8 times lower than without 131 I in the phantom. Quantitative peri-therapeutic 124 I-PET is feasible.

Determination of mammalian cell counts, cell size and cell health using the Moxi Z mini automated cell counter.

PubMed

Dittami, Gregory M; Sethi, Manju; Rabbitt, Richard D; Ayliffe, H Edward

2012-06-21

Particle and cell counting is used for a variety of applications including routine cell culture, hematological analysis, and industrial controls(1-5). A critical breakthrough in cell/particle counting technologies was the development of the Coulter technique by Wallace Coulter over 50 years ago. The technique involves the application of an electric field across a micron-sized aperture and hydrodynamically focusing single particles through the aperture. The resulting occlusion of the aperture by the particles yields a measurable change in electric impedance that can be directly and precisely correlated to cell size/volume. The recognition of the approach as the benchmark in cell/particle counting stems from the extraordinary precision and accuracy of its particle sizing and counts, particularly as compared to manual and imaging based technologies (accuracies on the order of 98% for Coulter counters versus 75-80% for manual and vision-based systems). This can be attributed to the fact that, unlike imaging-based approaches to cell counting, the Coulter Technique makes a true three-dimensional (3-D) measurement of cells/particles which dramatically reduces count interference from debris and clustering by calculating precise volumetric information about the cells/particles. Overall this provides a means for enumerating and sizing cells in a more accurate, less tedious, less time-consuming, and less subjective means than other counting techniques(6). Despite the prominence of the Coulter technique in cell counting, its widespread use in routine biological studies has been prohibitive due to the cost and size of traditional instruments. Although a less expensive Coulter-based instrument has been produced, it has limitations as compared to its more expensive counterparts in the correction for "coincidence events" in which two or more cells pass through the aperture and are measured simultaneously. Another limitation with existing Coulter technologies is the lack of metrics on the overall health of cell samples. Consequently, additional techniques must often be used in conjunction with Coulter counting to assess cell viability. This extends experimental setup time and cost since the traditional methods of viability assessment require cell staining and/or use of expensive and cumbersome equipment such as a flow cytometer. The Moxi Z mini automated cell counter, described here, is an ultra-small benchtop instrument that combines the accuracy of the Coulter Principle with a thin-film sensor technology to enable precise sizing and counting of particles ranging from 3-25 microns, depending on the cell counting cassette used. The M type cassette can be used to count particles from with average diameters of 4 - 25 microns (dynamic range 2 - 34 microns), and the Type S cassette can be used to count particles with and average diameter of 3 - 20 microns (dynamic range 2 - 26 microns). Since the system uses a volumetric measurement method, the 4-25 microns corresponds to a cell volume range of 34 - 8,180 fL and the 3 - 20 microns corresponds to a cell volume range of 14 - 4200 fL, which is relevant when non-spherical particles are being measured. To perform mammalian cell counts using the Moxi Z, the cells to be counted are first diluted with ORFLO or similar diluent. A cell counting cassette is inserted into the instrument, and the sample is loaded into the port of the cassette. Thousands of cells are pulled, single-file through a "Cell Sensing Zone" (CSZ) in the thin-film membrane over 8-15 seconds. Following the run, the instrument uses proprietary curve-fitting in conjunction with a proprietary software algorithm to provide coincidence event correction along with an assessment of overall culture health by determining the ratio of the number of cells in the population of interest to the total number of particles. The total particle counts include shrunken and broken down dead cells, as well as other debris and contaminants. The results are presented in histogram format with an automatic curve fit, with gates that can be adjusted manually as needed. Ultimately, the Moxi Z enables counting with a precision and accuracy comparable to a Coulter Z2, the current gold standard, while providing additional culture health information. Furthermore it achieves these results in less time, with a smaller footprint, with significantly easier operation and maintenance, and at a fraction of the cost of comparable technologies.

Note: An improved 3D imaging system for electron-electron coincidence measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Yun Fei; Lee, Suk Kyoung; Adhikari, Pradip

We demonstrate an improved imaging system that can achieve highly efficient 3D detection of two electrons in coincidence. The imaging system is based on a fast frame complementary metal-oxide semiconductor camera and a high-speed waveform digitizer. We have shown previously that this detection system is capable of 3D detection of ions and electrons with good temporal and spatial resolution. Here, we show that with a new timing analysis algorithm, this system can achieve an unprecedented dead-time (<0.7 ns) and dead-space (<1 mm) when detecting two electrons. A true zero dead-time detection is also demonstrated.

Note: An improved 3D imaging system for electron-electron coincidence measurements

NASA Astrophysics Data System (ADS)

Lin, Yun Fei; Lee, Suk Kyoung; Adhikari, Pradip; Herath, Thushani; Lingenfelter, Steven; Winney, Alexander H.; Li, Wen

2015-09-01

We demonstrate an improved imaging system that can achieve highly efficient 3D detection of two electrons in coincidence. The imaging system is based on a fast frame complementary metal-oxide semiconductor camera and a high-speed waveform digitizer. We have shown previously that this detection system is capable of 3D detection of ions and electrons with good temporal and spatial resolution. Here, we show that with a new timing analysis algorithm, this system can achieve an unprecedented dead-time (<0.7 ns) and dead-space (<1 mm) when detecting two electrons. A true zero dead-time detection is also demonstrated.

Monitoring the Dead Sea Region by Multi-Parameter Stations

NASA Astrophysics Data System (ADS)

Mohsen, A.; Weber, M. H.; Kottmeier, C.; Asch, G.

2015-12-01

The Dead Sea Region is an exceptional ecosystem whose seismic activity has influenced all facets of the development, from ground water availability to human evolution. Israelis, Palestinians and Jordanians living in the Dead Sea region are exposed to severe earthquake hazard. Repeatedly large earthquakes (e.g. 1927, magnitude 6.0; (Ambraseys, 2009)) shook the whole Dead Sea region proving that earthquake hazard knows no borders and damaging seismic events can strike anytime. Combined with the high vulnerability of cities in the region and with the enormous concentration of historical values this natural hazard results in an extreme earthquake risk. Thus, an integration of earthquake parameters at all scales (size and time) and their combination with data of infrastructure are needed with the specific aim of providing a state-of-the-art seismic hazard assessment for the Dead Sea region as well as a first quantitative estimate of vulnerability and risk. A strong motivation for our research is the lack of reliable multi-parameter ground-based geophysical information on earthquakes in the Dead Sea region. The proposed set up of a number of observatories with on-line data access will enable to derive the present-day seismicity and deformation pattern in the Dead Sea region. The first multi-parameter stations were installed in Jordan, Israel and Palestine for long-time monitoring. All partners will jointly use these locations. All stations will have an open data policy, with the Deutsches GeoForschungsZentrum (GFZ, Potsdam, Germany) providing the hard and software for real-time data transmission via satellite to Germany, where all partners can access the data via standard data protocols.

Avian community responses to post-fire forest structure: Implications for fire management in mixed conifer forests

USGS Publications Warehouse

White, Angela M.; Manley, Patricia N.; Tarbill, Gina; Richardson, T.L.; Russell, Robin E.; Safford, Hugh D.; Dobrowski, Solomon Z.

2015-01-01

Fire is a natural process and the dominant disturbance shaping plant and animal communities in many coniferous forests of the western US. Given that fire size and severity are predicted to increase in the future, it has become increasingly important to understand how wildlife responds to fire and post-fire management. The Angora Fire burned 1243 hectares of mixed conifer forest in South Lake Tahoe, California. We conducted avian point counts for the first 3 years following the fire in burned and unburned areas to investigate which habitat characteristics are most important for re-establishing or maintaining the native avian community in post-fire landscapes. We used a multi-species occurrence model to estimate how avian species are influenced by the density of live and dead trees and shrub cover. While accounting for variations in the detectability of species, our approach estimated the occurrence probabilities of all species detected including those that were rare or observed infrequently. Although all species encountered in this study were detected in burned areas, species-specific modeling results predicted that some species were strongly associated with specific post-fire conditions, such as a high density of dead trees, open-canopy conditions or high levels of shrub cover that occur at particular burn severities or at a particular time following fire. These results indicate that prescribed fire or managed wildfire which burns at low to moderate severity without at least some high-severity effects is both unlikely to result in the species assemblages that are unique to post-fire areas or to provide habitat for burn specialists. Additionally, the probability of occurrence for many species was associated with high levels of standing dead trees indicating that intensive post-fire harvest of these structures could negatively impact habitat of a considerable proportion of the avian community.

Dead bacteria reverse antibiotic-induced host defense impairment in burns.

PubMed

Chen, Lee-Wei; Chen, Pei-Hsuan; Fung, Chang-Phone; Hsu, Ching-Mei

2014-10-01

Burn patients can incur high rates of hospital-acquired infections. The mechanism of antibiotic exposure on inducing infection vulnerability has not been determined. This study aimed to examine the effects of antibiotic treatment on host defense mechanisms. First we treated C57/BL6 mice with combined antibiotic treatment after 30% to 35% total body surface area burn. Animals were sacrificed at 48 hours after sham or thermal injury treatment. Bacterial counts in intestinal lumen and mucosa were measured. Next, we treated animals with or without oral dead Escherichia coli or Staphylococcus aureus supplementation to stimulate Toll-like receptor in the intestinal mucosa. Toll-like receptor 4, antibacterial protein expression, nuclear factor (NF)-κB DNA-binding activity, and bacteria-killing activity in the intestinal mucosa; intestinal permeability; bacterial translocation to mesenteric lymph nodes; Klebsiella pneumoniae translocation; interleukin-6 in the blood; and phagocytic activity of alveolar macrophages, were assessed. Thermal injury increased microflora and NF-κB DNA-binding activity of the intestine. Systemic antibiotic treatment decreased gut microflora and increased bacterial translocation to mesenteric lymph nodes, intestinal permeability, and interleukin-6 levels in the blood. Antibiotic treatment also decreased bacteria-killing activity in intestinal mucosa and phagocytic activity of alveolar macrophages. Oral dead E coli and S aureus supplementation induced NF-κB DNA-binding activity, Toll-like receptor 4, and antibacterial protein expression of the intestinal mucosa. Taken together with the fact that dead bacteria reversed antibiotic-induced K pneumoniae translocation and intestinal and pulmonary defense impairment, we conclude that combined antibiotic treatment results in systemic host defense impairment in burns through the decrease in intestinal flora. We suggest that dead bacteria supplementation could induce nondefensin protein expression and reverse antibiotic-induced gut and lung defense impairment in burn patients. Copyright © 2014 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

[Morphological characteristics of inflammation in HIV-associated pulmonary tuberculosis with regard to the expression of myeloperoxidase].

PubMed

Bykhalov, L S; Smirnov, A V

2015-01-01

to characterize the morphological features of inflammation and the degree of myeloperoxidase expression in the lung of patients who died from HIV-associated tuberculosis (TB). Autopsy lung tissue specimens from 229 patients with HIV-associated TB were examined. A comparison group consisted of dead TB mono-infected patients (n = 30). Dead HIV/TB co-infected patients were divided into subgroups: 1) 50 patients with Stage 4A-4B and a CD4(+)-lymphocyte count of more than 200 cells/µl; 2) 54 with Stage 4B-4C and a CD4(+)-lymphocyte count of 100 to 200 cells/µl; 3) 125 with Stage 4C-5 and a CD4(+)-lymphocyte count of less than 100 cells/µl. Histological and immunohistochemical examinations of lung slices were performed using antibodies to myeloperoxidase (MPO). The predominant types of an inflammatory response were revealed according to the level of CD4+ lymphocytes. The lungs in Subgroup 1 showed a predominant typical granulomatous response (82%). Subgroup 2 exhibited an exudative-productive inflammatory response (57.4%) while Subgroup 3 displayed an alterative necrotic type (92.8%). Subgroup 3 showed the most marked reduction in lymphocyte numbers in the areas of inflammation, which was accompanied by a significant increase in the relative density and other morphometric parameters of MPO-positive macrophages and granulocytes in the inflammatory infiltration zones and alveolar walls. The identified changes in the lungs suggest that there is a decline in the magnitude of a delayed type hypersensitivity reaction, a progression of alterative necrotic processes as CD4(+) lymphocytes decrease in the systemic blood flow, and an increase in the proportion of functionally immature macrophages in the areas of inflammation, which reflects a substantially impaired local immune response to the persistence of M. tuberculosis in HIV infection.

Performance revaluation of a N-type coaxial HPGe detector with front edges crystal using MCNPX.

PubMed

Azli, Tarek; Chaoui, Zine-El-Abidine

2015-03-01

The MCNPX code was used to determine the efficiency of a N-type HPGe detector after two decades of operation. Accounting for the roundedness of the crystal`s front edges and an inhomogeneous description of the detector's dead layers were shown to achieve better agreement between measurements and simulation efficiency determination. The calculations were experimentally verified using point sources in the energy range from 50keV to 1400keV, and an overall uncertainty less than 2% was achieved. In order to use the detector for different matrices and geometries in radioactivity, the suggested model was validated by changing the counting geometry and by using multi-gamma disc sources. The introduced simulation approach permitted the revaluation of the performance of an HPGe detector in comparison of its initial condition, which is a useful tool for precise determination of the thickness of the inhomogeneous dead layer. Copyright © 2014 Elsevier Ltd. All rights reserved.

Growth responses of mature loblolly pine to dead wood manipulations

Treesearch

Michael D. Ulyshen; Scott Horn; James L. Hanula

2012-01-01

Large-scale manipulations of dead wood in mature Pinus taeda L. stands in the southeastern United States included a major one-time input of logs (fivefold increase in log volume) created by felling trees onsite, annual removals of all dead wood above ≥10 cm in diameter and ≥60 cm in length, and a reference in which no...

Controls on terrestrial carbon feedbacks by productivity versus turnover in the CMIP5 Earth System Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koven, C. D.; Chambers, J. Q.; Georgiou, K.

To better understand sources of uncertainty in projections of terrestrial carbon cycle feedbacks, we present an approach to separate the controls on modeled carbon changes. We separate carbon changes into four categories using a linearized, equilibrium approach: those arising from changed inputs (productivity-driven changes), and outputs (turnover-driven changes), of both the live and dead carbon pools. Using Coupled Model Intercomparison Project Phase 5 (CMIP5) simulations for five models, we find that changes to the live pools are primarily explained by productivity-driven changes, with only one model showing large compensating changes to live carbon turnover times. For dead carbon pools, themore » situation is more complex as all models predict a large reduction in turnover times in response to increases in productivity. This response arises from the common representation of a broad spectrum of decomposition turnover times via a multi-pool approach, in which flux-weighted turnover times are faster than mass-weighted turnover times. This leads to a shift in the distribution of carbon among dead pools in response to changes in inputs, and therefore a transient but long-lived reduction in turnover times. Since this behavior, a reduction in inferred turnover times resulting from an increase in inputs, is superficially similar to priming processes, but occurring without the mechanisms responsible for priming, we call the phenomenon "false priming", and show that it masks much of the intrinsic changes to dead carbon turnover times as a result of changing climate. These patterns hold across the fully coupled, biogeochemically coupled, and radiatively coupled 1 % yr −1 increasing CO 2 experiments. We disaggregate inter-model uncertainty in the globally integrated equilibrium carbon responses to initial turnover times, initial productivity, fractional changes in turnover, and fractional changes in productivity. For both the live and dead carbon pools, inter-model spread in carbon changes arising from initial conditions is dominated by model disagreement on turnover times, whereas inter-model spread in carbon changes from fractional changes to these terms is dominated by model disagreement on changes to productivity in response to both warming and CO 2 fertilization. However, the lack of changing turnover time control on carbon responses, for both live and dead carbon pools, in response to the imposed forcings may arise from a common lack of process representation behind changing turnover times (e.g., allocation and mortality for live carbon; permafrost, microbial dynamics, and mineral stabilization for dead carbon), rather than a true estimate of the importance of these processes.« less

Controls on terrestrial carbon feedbacks by productivity versus turnover in the CMIP5 Earth System Models

DOE PAGES

Koven, C. D.; Chambers, J. Q.; Georgiou, K.; ...

2015-09-07

To better understand sources of uncertainty in projections of terrestrial carbon cycle feedbacks, we present an approach to separate the controls on modeled carbon changes. We separate carbon changes into four categories using a linearized, equilibrium approach: those arising from changed inputs (productivity-driven changes), and outputs (turnover-driven changes), of both the live and dead carbon pools. Using Coupled Model Intercomparison Project Phase 5 (CMIP5) simulations for five models, we find that changes to the live pools are primarily explained by productivity-driven changes, with only one model showing large compensating changes to live carbon turnover times. For dead carbon pools, themore » situation is more complex as all models predict a large reduction in turnover times in response to increases in productivity. This response arises from the common representation of a broad spectrum of decomposition turnover times via a multi-pool approach, in which flux-weighted turnover times are faster than mass-weighted turnover times. This leads to a shift in the distribution of carbon among dead pools in response to changes in inputs, and therefore a transient but long-lived reduction in turnover times. Since this behavior, a reduction in inferred turnover times resulting from an increase in inputs, is superficially similar to priming processes, but occurring without the mechanisms responsible for priming, we call the phenomenon "false priming", and show that it masks much of the intrinsic changes to dead carbon turnover times as a result of changing climate. These patterns hold across the fully coupled, biogeochemically coupled, and radiatively coupled 1 % yr −1 increasing CO 2 experiments. We disaggregate inter-model uncertainty in the globally integrated equilibrium carbon responses to initial turnover times, initial productivity, fractional changes in turnover, and fractional changes in productivity. For both the live and dead carbon pools, inter-model spread in carbon changes arising from initial conditions is dominated by model disagreement on turnover times, whereas inter-model spread in carbon changes from fractional changes to these terms is dominated by model disagreement on changes to productivity in response to both warming and CO 2 fertilization. However, the lack of changing turnover time control on carbon responses, for both live and dead carbon pools, in response to the imposed forcings may arise from a common lack of process representation behind changing turnover times (e.g., allocation and mortality for live carbon; permafrost, microbial dynamics, and mineral stabilization for dead carbon), rather than a true estimate of the importance of these processes.« less

Photon-Counting Multikilohertz Microlaser Altimeters for Airborne and Spaceborne Topographic Measurements

NASA Technical Reports Server (NTRS)

Degnan, John J.; Smith, David E. (Technical Monitor)

2000-01-01

We consider the optimum design of photon-counting microlaser altimeters operating from airborne and spaceborne platforms under both day and night conditions. Extremely compact Q-switched microlaser transmitters produce trains of low energy pulses at multi-kHz rates and can easily generate subnanosecond pulse-widths for precise ranging. To guide the design, we have modeled the solar noise background and developed simple algorithms, based on Post-Detection Poisson Filtering (PDPF), to optimally extract the weak altimeter signal from a high noise background during daytime operations. Practical technology issues, such as detector and/or receiver dead times, have also been considered in the analysis. We describe an airborne prototype, being developed under NASA's instrument Incubator Program, which is designed to operate at a 10 kHz rate from aircraft cruise altitudes up to 12 km with laser pulse energies on the order of a few microjoules. We also analyze a compact and power efficient system designed to operate from Mars orbit at an altitude of 300 km and sample the Martian surface at rates up to 4.3 kHz using a 1 watt laser transmitter and an 18 cm telescope. This yields a Power-Aperture Product of 0.24 W-square meter, corresponding to a value almost 4 times smaller than the Mars Orbiting Laser Altimeter (0. 88W-square meter), yet the sampling rate is roughly 400 times greater (4 kHz vs 10 Hz) Relative to conventional high power laser altimeters, advantages of photon-counting laser altimeters include: (1) a more efficient use of available laser photons providing up to two orders of magnitude greater surface sampling rates for a given laser power-telescope aperture product; (2) a simultaneous two order of magnitude reduction in the volume, cost and weight of the telescope system; (3) the unique ability to spatially resolve the source of the surface return in a photon counting mode through the use of pixellated or imaging detectors; and (4) improved vertical and transverse spatial resolution resulting from both (1) and (3). Furthermore, because of significantly lower laser pulse energies, the microaltimeter is inherently more eyesafe to observers on the ground and less prone to internal optical damage, which can terminate a space mission prematurely.

The effects of sodium hypochlorite and chlorhexidine irrigants on the antibacterial activities of alkaline media against Enterococcus faecalis.

PubMed

Ma, Jinglei; Tong, Zhongchun; Ling, Junqi; Liu, Hongyan; Wei, Xi

2015-07-01

Sodium hypochlorite (NaOCl), chlorhexidine (CHX) and calcium hydroxide are common intracanal medicaments. The present study aimed to evaluate the effects of NaOCl and CHX on the antibacterial activities of alkaline media against Enterococcus faecalis. The survival rates of planktonic and biofilm E. faecalis were evaluated by plate counts after 1 min of pretreatment with NaOCl and CHX, and time-kill assays were then used to assess subsequent pH alkaline challenges. Dead and living cells in the E. faecalis biofilm were assessed with SYTO 9 and PI staining in combination with confocal laser scanning microscopy following exposure to NaOCl or CHX and subsequent alkaline challenges by common root canal irrigation and dressing procedures. One minute of pretreatment with 2% CHX, 0.2% CHX, or 5.25% NaOCl in combination with a subsequent alkaline challenge significantly decreased planktonic E. faecalis survival rates, but pretreatment with 1% NaOCl did not. The E. faecalis biofilm survival rates were reduced in the subsequent alkaline challenge following CHX pretreatment but gradually increased following NaOCl pretreatment. Similarly, CLSM analysis revealed that the greatest proportions of dead E. faecalis cells in the biofilms were presented in the CHX and alkaline treatment group. CHX might be more effective in improving the antibacterial activities of alkaline root canal medicaments against E. faecalis than NaOCl during routine root canal therapy procedures. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Biological Activity of alpha-Mangostin, a Larvicidal Botanic Mosquito Sterol Carrier Protein-2 Inhibitor

DTIC Science & Technology

2010-01-01

were then hatched in aluminum trays Þlled with deionized water. The larvae were provided a diet of VitaPro Plus Þsh food and brewerÕs yeast at a 2:1...deionized water, left overnight, and transferred to a plastic tray containing distilled water. A powdered diet (2:1 pot belly pig chow:brewerÕs yeast... powdered diet every other day. DMSO equivalents were used as the con- trol. The number of living and dead larvae was counted 72 h after the start of

Integrated WiFi/PDR/Smartphone Using an Unscented Kalman Filter Algorithm for 3D Indoor Localization.

PubMed

Chen, Guoliang; Meng, Xiaolin; Wang, Yunjia; Zhang, Yanzhe; Tian, Peng; Yang, Huachao

2015-09-23

Because of the high calculation cost and poor performance of a traditional planar map when dealing with complicated indoor geographic information, a WiFi fingerprint indoor positioning system cannot be widely employed on a smartphone platform. By making full use of the hardware sensors embedded in the smartphone, this study proposes an integrated approach to a three-dimensional (3D) indoor positioning system. First, an improved K-means clustering method is adopted to reduce the fingerprint database retrieval time and enhance positioning efficiency. Next, with the mobile phone's acceleration sensor, a new step counting method based on auto-correlation analysis is proposed to achieve cell phone inertial navigation positioning. Furthermore, the integration of WiFi positioning with Pedestrian Dead Reckoning (PDR) obtains higher positional accuracy with the help of the Unscented Kalman Filter algorithm. Finally, a hybrid 3D positioning system based on Unity 3D, which can carry out real-time positioning for targets in 3D scenes, is designed for the fluent operation of mobile terminals.

Integrated WiFi/PDR/Smartphone Using an Unscented Kalman Filter Algorithm for 3D Indoor Localization

PubMed Central

Chen, Guoliang; Meng, Xiaolin; Wang, Yunjia; Zhang, Yanzhe; Tian, Peng; Yang, Huachao

2015-01-01

Because of the high calculation cost and poor performance of a traditional planar map when dealing with complicated indoor geographic information, a WiFi fingerprint indoor positioning system cannot be widely employed on a smartphone platform. By making full use of the hardware sensors embedded in the smartphone, this study proposes an integrated approach to a three-dimensional (3D) indoor positioning system. First, an improved K-means clustering method is adopted to reduce the fingerprint database retrieval time and enhance positioning efficiency. Next, with the mobile phone’s acceleration sensor, a new step counting method based on auto-correlation analysis is proposed to achieve cell phone inertial navigation positioning. Furthermore, the integration of WiFi positioning with Pedestrian Dead Reckoning (PDR) obtains higher positional accuracy with the help of the Unscented Kalman Filter algorithm. Finally, a hybrid 3D positioning system based on Unity 3D, which can carry out real-time positioning for targets in 3D scenes, is designed for the fluent operation of mobile terminals. PMID:26404314

Graphene Josephson Junction Single Photon Detector

NASA Astrophysics Data System (ADS)

Walsh, Evan D.; Lee, Gil-Ho; Efetov, Dmitri K.; Heuck, Mikkel; Crossno, Jesse; Taniguchi, Takashi; Watanabe, Kenji; Ohki, Thomas A.; Kim, Philip; Englund, Dirk; Fong, Kin Chung

Single photon detectors (SPDs) have found use across a wide array of applications depending on the wavelength to which they are sensitive. Graphene, because of its linear, gapless dispersion near the Dirac point, has a flat, wide bandwidth absorption that can be enhanced to near 100 % through the use of resonant structures making it a promising candidate for broadband SPDs. Upon absorbing a photon in the optical to mid-infrared range, a small (~10 μm2) sheet of graphene at cryogenic temperatures can experience a significant increase in electronic temperature due to its extremely low heat capacity. At 1550 nm, for example, calculations show that the temperature could rise by as much as 500 %. This temperature increase could be detected with near perfect quantum efficiency by making the graphene the weak link in a Josephson junction (JJ). We present a theoretical model demonstrating that such a graphene JJ SPD could operate at the readily achievable temperature of 3 K with near zero dark count, sub-50 ps timing jitter, and sub-5 ns dead time and report on the progress toward experimentally realizing the device.

Spontaneous abortions after the Three Mile Island nuclear accident: a life table analysis.

PubMed Central

Goldhaber, M K; Staub, S L; Tokuhata, G K

1983-01-01

A study was conducted to determine whether the incidence of spontaneous abortion was greater than expected near the Three Mile Island (TMI) nuclear power plant during the months following the March 28, 1979 accident. All persons living within five miles of TMI were registered shortly after the accident, and information on pregnancy at the time of the accident was collected. After one year, all pregnancy cases were followed up and outcomes ascertained. Using the life table method, it was found that, given pregnancies after four completed weeks of gestation counting from the first day of the last menstrual period, the estimated incidence of spontaneous abortion (miscarriage before completion of 16 weeks of gestation) was 15.1 per cent for women pregnant at the time of the TMI accident. Combining spontaneous abortions and stillbirths (delivery of a dead fetus after 16 weeks of gestation), the estimated incidence was 16.1 per cent for pregnancies after four completed weeks of gestation. Both incidences are comparable to baseline studies of fetal loss. PMID:6859357

Role of More Active Identification of Brain-Dead Cases in Increasing Organ Donation.

PubMed

Sadegh Beigee, Farahnaz; Mohsenzadeh, Mojtaba; Shahryari, Shagin; Mojtabaee, Meysam

2017-02-01

Organ donor shortage is a worldwide problem, resulting in 10% to 30% mortality rates for patients on wait lists for organ transplant. For brain-dead patients in Iran, it is mandatory for intensive care unit patients with Glasgow Coma Scale below 5/15 to be reported to an organ procurement unit. However, this process has not been functioning effectively. Here, we present the effects of changing the strategies on detecting brain-dead cases on the organ donor pool. From March 2015 to March 2016, we changed our strategy in active detection of brain-dead cases. Since March 2015, our newly established protocol for active detection of brain-dead cases includes the following changes: (1) instead of calling high-volume intensive care units 3 times per week, we switched to calling every day in the morning; (2) instead of calling low-volume intensive care units 1 time per week, we switched to calling 3 times per week; (3) we included intensive care units (cardiac and general), neurosurgery, and emergency departments, as well as nursing supervisor offices, in our call and visit lists; and (4) we increased visits to wards by our trained staff as inspectors. From March 2015 to March 2016, the number of reported suspected brain-dead cases has increased from 224 to 460 per year, with proven brain death increasing from 180 to 306 cases. The actual number of donors has also increased, from 116 to 165 donations (53% increase) over 1 year. More proactive strategies have had significant effects on brain-dead detection, resulting in significantly increased donor pools and organ donations. In countries with low cooperation of hospital staff, more proactive engagement in detecting brain-dead cases is a good solution to prevent loss of potential organ donors, with a final result of decreasing wait list mortality.

Quantitative Detection of Viable Bifidobacterium bifidum BF-1 Cells in Human Feces by Using Propidium Monoazide and Strain-Specific Primers

PubMed Central

Fujimoto, Junji

2013-01-01

We developed a PCR-based method to detect and quantify viable Bifidobacterium bifidum BF-1 cells in human feces. This method (PMA-qPCR) uses propidium monoazide (PMA) to distinguish viable from dead cells and quantitative PCR using a BF-1-specific primer set designed from the results of randomly amplified polymorphic DNA analysis. During long-term culture (10 days), the number of viable BF-1 cells detected by counting the number of CFU on modified MRS agar, by measuring the ATP contents converted to CFU, and by using PMA-qPCR decreased from about 1010 to 106 cells/ml; in contrast, the total number of (viable and dead) BF-1 cells detected by counting 4′,6-diamidino-2-phenylindolee (DAPI)-stained cells and by using qPCR without PMA and reverse transcription-qPCR remained constant. The number of viable BF-1 cells in fecal samples detected by using PMA-qPCR was highly and significantly correlated with the number of viable BF-1 cells added to the fecal samples, within the range of 105.3 to 1010.3 cells/g feces (wet weight) (r > 0.99, P < 0.001). After 12 healthy subjects ingested 1010.3 to 1011.0 CFU of BF-1 in a fermented milk product daily for 28 days, 104.5 ± 1.5 (mean ± standard deviation [SD]) BF-1 CFU/g was detected in fecal samples by using strain-specific selective agar; in contrast, 106.2 ± 0.4 viable BF-1 cells/g were detected by using PMA-qPCR, and a total of 107.6 ± 0.7 BF-1 cells/g were detected by using qPCR without PMA. Thus, the number of viable BF-1 cells detected by PMA-qPCR was about 50 times higher (P < 0.01) than that detected by the culture-dependent method. We conclude that strain-specific PMA-qPCR can be used to quickly and accurately evaluate viable BF-1 in feces. PMID:23354719

SOLARTRAK. Solar Array Tracking Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manish, A.B.; Dudley, J.

1995-06-01

SolarTrak used in conjunction with various versions of 68HC11-based SolarTrack hardware boards provides control system for one or two axis solar tracking arrays. Sun position is computed from stored position data and time from an on-board clock/calendar chip. Position feedback can be by one or two offset motor turn counter square wave signals per axis, or by a position potentiometer. A limit of 256 counts resolution is imposed by the on-board analog to digital (A/D) convertor. Control is provided for one or two motors. Numerous options are provided to customize the controller for specific applications. Some options are imposed atmore » compile time, some are setable during operation. Software and hardware board designs are provided for Control Board and separate User Interface Board that accesses and displays variables from Control Board. Controller can be used with range of sensor options ranging from a single turn count sensor per motor to systems using dual turn-count sensors, limit sensors, and a zero reference sensor. Dual axis trackers oriented azimuth elevation, east west, north south, or polar declination can be controlled. Misalignments from these orientations can also be accommodated. The software performs a coordinate transformation using six parameters to compute sun position in misaligned coordinates of the tracker. Parameters account for tilt of tracker in two directions, rotation about each axis, and gear ration errors in each axis. The software can even measure and compute these prameters during an initial setup period if current from a sun position sensor or output from photovoltaic array is available as an anlog voltage to the control board`s A/D port. Wind or emergency stow to aj present position is available triggered by digital or analog signals. Night stow is also available. Tracking dead band is adjustable from narrow to wide. Numerous features of the hardware and software conserve energy for use with battery powered systems.« less

Solar Array Tracking Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maish, Alexander

1995-06-22

SolarTrak used in conjunction with various versions of 68HC11-based SolarTrack hardware boards provides control system for one or two axis solar tracking arrays. Sun position is computed from stored position data and time from an on-board clock/calendar chip. Position feedback can be by one or two offset motor turn counter square wave signals per axis, or by a position potentiometer. A limit of 256 counts resolution is imposed by the on-board analog to digital (A/D) convertor. Control is provided for one or two motors. Numerous options are provided to customize the controller for specific applications. Some options are imposed atmore » compile time, some are setable during operation. Software and hardware board designs are provided for Control Board and separate User Interface Board that accesses and displays variables from Control Board. Controller can be used with range of sensor options ranging from a single turn count sensor per motor to systems using dual turn-count sensors, limit sensors, and a zero reference sensor. Dual axis trackers oriented azimuth elevation, east west, north south, or polar declination can be controlled. Misalignments from these orientations can also be accommodated. The software performs a coordinate transformation using six parameters to compute sun position in misaligned coordinates of the tracker. Parameters account for tilt of tracker in two directions, rotation about each axis, and gear ration errors in each axis. The software can even measure and compute these prameters during an initial setup period if current from a sun position sensor or output from photovoltaic array is available as an anlog voltage to the control board''s A/D port. Wind or emergency stow to aj present position is available triggered by digital or analog signals. Night stow is also available. Tracking dead band is adjustable from narrow to wide. Numerous features of the hardware and software conserve energy for use with battery powered systems.« less

On the decades-long stability of the interstellar wind through the solar system

NASA Astrophysics Data System (ADS)

Lallement, R.; Bertaux, J. L.

2014-05-01

We have revisited the series of observations recently used to infer a temporal variation in the interstellar helium flow over the past forty years. Concerning the recent IBEX-Lo direct detection of helium neutrals, there are two types of precise and unambiguous measurements that do not rely on the exact response of the instrument: the count rate maxima as a function of the spin angle, which determines the ecliptic latitude of the flow, and the count rate maxima as a function of IBEX longitude, which determines a tight relationship between the ecliptic longitude of the flow and its velocity far from the Sun. These measurements provide parameters (and couples of parameters in the second case) that are remarkably similar to the canonical, old values. In contrast, the preferred choice of a lower velocity and higher longitude reported before from IBEX data is only based on the count rate variation (at each spin phase maximum) as a function of the satellite longitude, when drifting across the region of high fluxes. We have examined the consequences of dead-time counting effects and conclude that including them at a realistic level is sufficient to reconcile the data with the old parameters, calling for further investigations. We discuss the analyses of the STEREO pickup ion data and argue that the statistical method that has been preferred to infer the neutral flow longitude (instead of the more direct method based on the pickup ion maximum flux directions) is not appropriate. Moreover, transport effects may have been significant at the very weak solar activity level of 2007-2009, in which case the longitudes of the pickup ion maxima are only upper limits on the flow longitude. Finally, we found that using some flow longitude determinations based on UV glow data is not adequate. Based on this global study, and at variance with recent conclusions, we find no evidence for a temporal variability of the interstellar helium flow. This has implications for inner and outer heliosphere studies.

Seasonal prevalence and intensity of hookworms (Uncinaria spp.) in California sea lion (Zalophus californianus) pups born in 2002 on San Miguel Island, California.

PubMed

Lyons, E T; Delong, R L; Spraker, T R; Melin, S R; Laake, J L; Tolliver, S C

2005-05-01

Intestines of California sea lion (Zalophus californianus) pups (n= 204), born in 2002 on San Miguel Island, California, were examined for hookworms (Uncinaria spp.) as part of a seasonal mortality study from June through December 2002 and January 2003. The investigation was planned to coincide with most of the previously established hookworm infection period of the pups. Prevalence of hookworms in dead pups was 100% for each month of the study. The geometric mean intensity of infections per month was: 94.03 (n=30) for June, 629.09 (n=50) for July, 319.90 (n=31) for August, 159.90 (n=30) for October, 109.03 (n=30) for November, 37.84 (n=24) for December 2002 and 11.05 (n=9) for January 2003. In addition to the temporal pattern, the infection intensity was higher for pups in good condition and for male pups. An inter-year comparison of hookworm counts from dead pups collected in July of 1996, 2000, and 2002 also demonstrated higher intensity in pups in better condition but sex-differences in intensity were inconsistent across years. The inter-year comparison also demonstrated higher intensities in dead pups collected from portions of the rookery with sandy substrate versus rocky substrate. No annual differences in intensity were found after adjusting for substrate and condition.

Hardware solution for continuous time-resolved burst detection of single molecules in flow

NASA Astrophysics Data System (ADS)

Wahl, Michael; Erdmann, Rainer; Lauritsen, Kristian; Rahn, Hans-Juergen

1998-04-01

Time Correlated Single Photon Counting (TCSPC) is a valuable tool for Single Molecule Detection (SMD). However, existing TCSPC systems did not support continuous data collection and processing as is desirable for applications such as SMD for e.g. DNA-sequencing in a liquid flow. First attempts at using existing instrumentation in this kind of operation mode required additional routing hardware to switch between several memory banks and were not truly continuous. We have designed a hard- and software system to perform continuous real-time TCSPC based upon a modern solid state Time to Digital Converter (TDC). Short dead times of the fully digital TDC design combined with fast Field Programmable Gay Array logic permit a continuous data throughput as high as 3 Mcounts/sec. The histogramming time may be set as short as 100 microsecond(s) . Every histogram or every single fluorescence photon can be real-time tagged at 200 ns resolution in addition to recording its arrival time relative to the excitation pulse. Continuous switching between memory banks permits concurrent histogramming and data read-out. The instrument provides a time resolution of 60 ps and up to 4096 histogram channels. The overall instrument response function in combination with a low cost picosecond diode laser and an inexpensive photomultiplier tube was found to be 180 ps and well sufficient to measure sub-nanosecond fluorescence lifetimes.

Assessing the role of natural disturbance and forest management on dead wood dynamics in mixed-species stands of central Maine, USA

Treesearch

Joshua J. Puhlick; Aaron R. Weiskittel; Shawn Fraver; Matthew B. Russell; Laura S. Kenefic

2016-01-01

Dead wood pools are strongly influenced by natural disturbance events, stand development processes, and forest management activities. However, the relative importance of these influences can vary over time. In this study, we evaluate the role of these factors on dead wood biomass pools across several forest management alternatives after 60 years of treatment on the...

A seamless acquisition digital storage oscilloscope with three-dimensional waveform display

NASA Astrophysics Data System (ADS)

Yang, Kuojun; Tian, Shulin; Zeng, Hao; Qiu, Lei; Guo, Lianping

2014-04-01

In traditional digital storage oscilloscope (DSO), sampled data need to be processed after each acquisition. During data processing, the acquisition is stopped and oscilloscope is blind to the input signal. Thus, this duration is called dead time. With the rapid development of modern electronic systems, the effect of infrequent events becomes significant. To capture these occasional events in shorter time, dead time in traditional DSO that causes the loss of measured signal needs to be reduced or even eliminated. In this paper, a seamless acquisition oscilloscope without dead time is proposed. In this oscilloscope, three-dimensional waveform mapping (TWM) technique, which converts sampled data to displayed waveform, is proposed. With this technique, not only the process speed is improved, but also the probability information of waveform is displayed with different brightness. Thus, a three-dimensional waveform is shown to the user. To reduce processing time further, parallel TWM which processes several sampled points simultaneously, and dual-port random access memory based pipelining technique which can process one sampling point in one clock period are proposed. Furthermore, two DDR3 (Double-Data-Rate Three Synchronous Dynamic Random Access Memory) are used for storing sampled data alternately, thus the acquisition can continue during data processing. Therefore, the dead time of DSO is eliminated. In addition, a double-pulse test method is adopted to test the waveform capturing rate (WCR) of the oscilloscope and a combined pulse test method is employed to evaluate the oscilloscope's capture ability comprehensively. The experiment results show that the WCR of the designed oscilloscope is 6 250 000 wfms/s (waveforms per second), the highest value in all existing oscilloscopes. The testing results also prove that there is no dead time in our oscilloscope, thus realizing the seamless acquisition.

A seamless acquisition digital storage oscilloscope with three-dimensional waveform display

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Kuojun, E-mail: kuojunyang@gmail.com; Guo, Lianping; School of Electrical and Electronic Engineering, Nanyang Technological University

In traditional digital storage oscilloscope (DSO), sampled data need to be processed after each acquisition. During data processing, the acquisition is stopped and oscilloscope is blind to the input signal. Thus, this duration is called dead time. With the rapid development of modern electronic systems, the effect of infrequent events becomes significant. To capture these occasional events in shorter time, dead time in traditional DSO that causes the loss of measured signal needs to be reduced or even eliminated. In this paper, a seamless acquisition oscilloscope without dead time is proposed. In this oscilloscope, three-dimensional waveform mapping (TWM) technique, whichmore » converts sampled data to displayed waveform, is proposed. With this technique, not only the process speed is improved, but also the probability information of waveform is displayed with different brightness. Thus, a three-dimensional waveform is shown to the user. To reduce processing time further, parallel TWM which processes several sampled points simultaneously, and dual-port random access memory based pipelining technique which can process one sampling point in one clock period are proposed. Furthermore, two DDR3 (Double-Data-Rate Three Synchronous Dynamic Random Access Memory) are used for storing sampled data alternately, thus the acquisition can continue during data processing. Therefore, the dead time of DSO is eliminated. In addition, a double-pulse test method is adopted to test the waveform capturing rate (WCR) of the oscilloscope and a combined pulse test method is employed to evaluate the oscilloscope's capture ability comprehensively. The experiment results show that the WCR of the designed oscilloscope is 6 250 000 wfms/s (waveforms per second), the highest value in all existing oscilloscopes. The testing results also prove that there is no dead time in our oscilloscope, thus realizing the seamless acquisition.« less

Analysis of dead zone sources in a closed-loop fiber optic gyroscope.

PubMed

Chong, Kyoung-Ho; Choi, Woo-Seok; Chong, Kil-To

2016-01-01

Analysis of the dead zone is among the intensive studies in a closed-loop fiber optic gyroscope. In a dead zone, a gyroscope cannot detect any rotation and produces a zero bias. In this study, an analysis of dead zone sources is performed in simulation and experiments. In general, the problem is mainly due to electrical cross coupling and phase modulation drift. Electrical cross coupling is caused by interference between modulation voltage and the photodetector. The cross-coupled signal produces spurious gyro bias and leads to a dead zone if it is larger than the input rate. Phase modulation drift as another dead zone source is due to the electrode contamination, the piezoelectric effect of the LiNbO3 substrate, or to organic fouling. This modulation drift lasts for a short or long period of time like a lead-lag filter response and produces gyro bias error, noise spikes, or dead zone. For a more detailed analysis, the cross-coupling effect and modulation phase drift are modeled as a filter and are simulated in both the open-loop and closed-loop modes. The sources of dead zone are more clearly analyzed in the simulation and experimental results.

Single-Photon-Sensitive HgCdTe Avalanche Photodiode Detector

NASA Technical Reports Server (NTRS)

Huntington, Andrew

2013-01-01

The purpose of this program was to develop single-photon-sensitive short-wavelength infrared (SWIR) and mid-wavelength infrared (MWIR) avalanche photodiode (APD) receivers based on linear-mode HgCdTe APDs, for application by NASA in light detection and ranging (lidar) sensors. Linear-mode photon-counting APDs are desired for lidar because they have a shorter pixel dead time than Geiger APDs, and can detect sequential pulse returns from multiple objects that are closely spaced in range. Linear-mode APDs can also measure photon number, which Geiger APDs cannot, adding an extra dimension to lidar scene data for multi-photon returns. High-gain APDs with low multiplication noise are required for efficient linear-mode detection of single photons because of APD gain statistics -- a low-excess-noise APD will generate detectible current pulses from single photon input at a much higher rate of occurrence than will a noisy APD operated at the same average gain. MWIR and LWIR electron-avalanche HgCdTe APDs have been shown to operate in linear mode at high average avalanche gain (M > 1000) without excess multiplication noise (F = 1), and are therefore very good candidates for linear-mode photon counting. However, detectors fashioned from these narrow-bandgap alloys require aggressive cooling to control thermal dark current. Wider-bandgap SWIR HgCdTe APDs were investigated in this program as a strategy to reduce detector cooling requirements.

Fast and simple method for determination of fatty acid methyl esters (FAME) in biodiesel blends using X-ray spectrometry.

PubMed

Sitko, Rafal; Zawisza, Beata; Kowalewska, Zofia; Kocot, Karina; Polowniak, Marzena

2011-09-30

The determination of fatty acid methyl esters (FAME) in diesel fuel blends is an important aspect of production and blending process as well as quality control of distribution operations. In this study, energy-dispersive X-ray fluorescence spectrometer (EDXRF) is used for the first time for determination of FAME in biodiesel blends. The principle of the method is based on intensity difference of X-ray radiation scattered from hydrocarbons and from FAME. The experiment shows that coherent and incoherent radiation, commonly applied for evaluation of the average atomic number of the sample with light matrix, cannot be applied for FAME determination. However, the application of scattered continuous radiation gives excellent correlation between FAME concentration and intensity of scattered radiation. The best results are obtained if continuum is collected in the range of energy between 10.5 and 15.0 keV for rhodium X-ray tube, operated at 35 kV. Linear relationship between the FAME concentration and the inverse of scattered continuous radiation is obtained with the correlation coefficients of 0.999. Standard deviation of measurement is ca. 0.46% (v/v) of FAME and detection limit is 1.2% (v/v) for 600 s counting time and 50% dead-time loss using Si-PIN detector. The investigation shows that crucial issue in determination of FAME in biodiesel blends using EDXRF spectrometer is the precision of measurements resulting from the counting statistics. Therefore, much better results (0.20% (v/v) standard deviation and 0.52% (v/v) detection limit) can be expected if higher intensity of primary radiation is applied and X-ray spectrum is collected by silicon drift detector of high input count rate. For concentration of FAME from 10 to 100% (v/v), the differences between reference method (Fourier transform infrared spectrometry) and the proposed method usually do not exceed 1% (v/v) of FAME. The proposed method is fast, simple and enables FAME determination in wide range of concentration up to 100% of FAME without any sample treatment. Copyright © 2011 Elsevier B.V. All rights reserved.

The dead donor rule: can it withstand critical scrutiny?

PubMed

Miller, Franklin G; Truog, Robert D; Brock, Dan W

2010-06-01

Transplantation of vital organs has been premised ethically and legally on "the dead donor rule" (DDR)-the requirement that donors are determined to be dead before these organs are procured. Nevertheless, scholars have argued cogently that donors of vital organs, including those diagnosed as "brain dead" and those declared dead according to cardiopulmonary criteria, are not in fact dead at the time that vital organs are being procured. In this article, we challenge the normative rationale for the DDR by rejecting the underlying premise that it is necessarily wrong for physicians to cause the death of patients and the claim that abandoning this rule would exploit vulnerable patients. We contend that it is ethical to procure vital organs from living patients sustained on life support prior to treatment withdrawal, provided that there is valid consent for both withdrawing treatment and organ donation. However, the conservatism of medical ethics and practical concerns make it doubtful that the DDR will be abandoned in the near future. This leaves the current practice of organ transplantation based on the "moral fiction" that donors are dead when vital organs are procured.

The effects of a western spruce budworm outbreak on the dead wood component in relation to ownership in forests of eastern Oregon

Treesearch

David Azuma

2010-01-01

Forest Inventory and Analysis data were used to investigate the effects of a severe western spruce budworm outbreak on the dead wood component of forests in 11 counties of eastern Oregon for two time periods. The ownership and the level of damage (as assessed by aerial surveys) affected the resulting down woody material and standing dead trees. The pattern of coarse...

33 CFR 183.105 - Quantity of flotation required.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the dead weight; and (3) A weight in pounds that, when submerged, equals 62.4 times the volume in... of this section, “dead weight” means the maximum weight capacity marked on the boat minus the persons...

33 CFR 183.105 - Quantity of flotation required.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of the dead weight; and (3) A weight in pounds that, when submerged, equals 62.4 times the volume in... of this section, “dead weight” means the maximum weight capacity marked on the boat minus the persons...

33 CFR 183.105 - Quantity of flotation required.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of the dead weight; and (3) A weight in pounds that, when submerged, equals 62.4 times the volume in... of this section, “dead weight” means the maximum weight capacity marked on the boat minus the persons...

33 CFR 183.105 - Quantity of flotation required.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the dead weight; and (3) A weight in pounds that, when submerged, equals 62.4 times the volume in... of this section, “dead weight” means the maximum weight capacity marked on the boat minus the persons...

33 CFR 183.105 - Quantity of flotation required.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of the dead weight; and (3) A weight in pounds that, when submerged, equals 62.4 times the volume in... of this section, “dead weight” means the maximum weight capacity marked on the boat minus the persons...

77 FR 12244 - Proposed Information Collection; Comment Request; Report of Whaling Operations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

... American whaling organization about strikes on and catch of whales. Anyone retrieving a dead whale is also... Respondents: 51. Estimated Time Per Response: 30 minutes for reports on whales struck or on recovery of dead...

Maia Mapper: high definition XRF imaging in the lab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryan, Chris G.; Kirkham, R.; Moorhead, G. F.

Here, Maia Mapper is a laboratory μXRF mapping system for efficient elemental imaging of drill core sections serving minerals research and industrial applications. It targets intermediate spatial scales, with imaging of up to ~80 M pixels over a 500×150 mm 2 sample area. It brings together (i) the Maia detector and imaging system, with its large solid-angle, event-mode operation, millisecond pixel transit times in fly-scan mode and real-time spectral deconvolution and imaging, (ii) the high brightness MetalJet D2 liquid metal micro-focus X-ray source from Excillum, and (iii) an efficient XOS polycapillary lens with a flux gain ~15,900 at 21 keVmore » into a ~32 μm focus, and (iv) a sample scanning stage engineered for standard drill-core sections. Count-rates up to ~3 M/s are observed on drill core samples with low dead-time up to ~1.5%. Automated scans are executed in sequence with display of deconvoluted element component images accumulated in real-time in the Maia detector. Application images on drill core and polished rock slabs illustrate Maia Mapper capabilities as part of the analytical workflow of the Advanced Resource Characterisation Facility, which spans spatial dimensions from ore deposit to atomic scales.« less

Maia Mapper: high definition XRF imaging in the lab

DOE PAGES

Ryan, Chris G.; Kirkham, R.; Moorhead, G. F.; ...

2018-03-13

Here, Maia Mapper is a laboratory μXRF mapping system for efficient elemental imaging of drill core sections serving minerals research and industrial applications. It targets intermediate spatial scales, with imaging of up to ~80 M pixels over a 500×150 mm 2 sample area. It brings together (i) the Maia detector and imaging system, with its large solid-angle, event-mode operation, millisecond pixel transit times in fly-scan mode and real-time spectral deconvolution and imaging, (ii) the high brightness MetalJet D2 liquid metal micro-focus X-ray source from Excillum, and (iii) an efficient XOS polycapillary lens with a flux gain ~15,900 at 21 keVmore » into a ~32 μm focus, and (iv) a sample scanning stage engineered for standard drill-core sections. Count-rates up to ~3 M/s are observed on drill core samples with low dead-time up to ~1.5%. Automated scans are executed in sequence with display of deconvoluted element component images accumulated in real-time in the Maia detector. Application images on drill core and polished rock slabs illustrate Maia Mapper capabilities as part of the analytical workflow of the Advanced Resource Characterisation Facility, which spans spatial dimensions from ore deposit to atomic scales.« less

Maia Mapper: high definition XRF imaging in the lab

NASA Astrophysics Data System (ADS)

Ryan, C. G.; Kirkham, R.; Moorhead, G. F.; Parry, D.; Jensen, M.; Faulks, A.; Hogan, S.; Dunn, P. A.; Dodanwela, R.; Fisher, L. A.; Pearce, M.; Siddons, D. P.; Kuczewski, A.; Lundström, U.; Trolliet, A.; Gao, N.

2018-03-01

Maia Mapper is a laboratory μXRF mapping system for efficient elemental imaging of drill core sections serving minerals research and industrial applications. It targets intermediate spatial scales, with imaging of up to ~80 M pixels over a 500×150 mm2 sample area. It brings together (i) the Maia detector and imaging system, with its large solid-angle, event-mode operation, millisecond pixel transit times in fly-scan mode and real-time spectral deconvolution and imaging, (ii) the high brightness MetalJet D2 liquid metal micro-focus X-ray source from Excillum, and (iii) an efficient XOS polycapillary lens with a flux gain ~15,900 at 21 keV into a ~32 μm focus, and (iv) a sample scanning stage engineered for standard drill-core sections. Count-rates up to ~3 M/s are observed on drill core samples with low dead-time up to ~1.5%. Automated scans are executed in sequence with display of deconvoluted element component images accumulated in real-time in the Maia detector. Application images on drill core and polished rock slabs illustrate Maia Mapper capabilities as part of the analytical workflow of the Advanced Resource Characterisation Facility, which spans spatial dimensions from ore deposit to atomic scales.

Spatio-temporal development of sinkholes on the eastern shore of the Dead Sea

NASA Astrophysics Data System (ADS)

Holohan, Eoghan; Saberi, Leila; Al-Halbouni, Djamil; Sawarieh, Ali; Closson, Damien; Alrshdan, Hussam; Walter, Thomas; Dahm, Torsten

2017-04-01

The ongoing, largely anthropogenically-forced decline of the Dead Sea is associated with the most prolific development of sinkholes worldwide. The fall in hydrological base level since the 1960s is thought to enable relatively fresh ground waters to dissolve underground salt deposits that were previously in equilibrium with hypersaline Dead Sea brine. Sinkhole development in response to this dissolution began in the 1980s and is still ongoing; it represents a significant geohazard in the Dead Sea region. We present new research undertaken within the Dead Sea Research Venue (DESERVE) on the spatio-temporal evolution of the main sinkhole-affected site on the Eastern shore of the Dead Sea, at Ghor Al-Haditha in Jordan. Our data set includes optical satellite imagery, aerial survey photographs and drone-based photogrammetric surveys with high spatial (< 1 m2 - 0.05 m per pixel) and temporal (decadal from 1970-2010, annual from 2004-2016) resolution. These enable new quantitative insights into this, the largest of all the Dead Sea sinkhole sites. Our analysis shows that there are now over 800 sinkholes at Ghor al-Haditha. Sinkholes initiated as spatially distinct clusters in the late 1980's to early 1990s. While some clusters have since become inactive, most have expanded and merged with time. New clusters have also developed, mainly in the more recently exposed north of the area. With the retreat of the Dead Sea, the roughly coastline-parallel zone of sinkhole formation has expanded unevenly but systematically seawards. Such a seaward migration of sinkhole formation is predicted from hydrogeological theory, but as yet not consistently observed elsewhere at the Dead Sea. The rate of sinkhole formation at Ghor Haditha accelerated markedly during the late 2000s to a peak of about 100 per year in 2009. Similar accelerations are observed on the western shore, but differ in timing. The rate of sinkhole formation on the Eastern shore has since declined to about 50 per year. Such differences in the overall spatio-temporal evolution of sinkholes on the eastern and western shores of the Dead Sea likely highlights the important role of local hydrogeological conditions and processes in governing sinkhole development.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fahim, Farah; Deptuch, Grzegorz; Shenai, Alpana

The Vertically Integrated Photon Imaging Chip - Large, (VIPIC-L), is a large area, small pixel (65μm), 3D integrated, photon counting ASIC with zero-suppressed or full frame dead-time-less data readout. It features data throughput of 14.4 Gbps per chip with a full frame readout speed of 56kframes/s in the imaging mode. VIPIC-L contain 192 x 192 pixel array and the total size of the chip is 1.248cm x 1.248cm with only a 5μm periphery. It contains about 120M transistors. A 1.3M pixel camera module will be developed by arranging a 6 x 6 array of 3D VIPIC-L’s bonded to a largemore » area silicon sensor on the analog side and to a readout board on the digital side. The readout board hosts a bank of FPGA’s, one per VIPIC-L to allow processing of up to 0.7 Tbps of raw data produced by the camera.« less

The 124Sb activity standardization by gamma spectrometry for medical applications

NASA Astrophysics Data System (ADS)

de Almeida, M. C. M.; Iwahara, A.; Delgado, J. U.; Poledna, R.; da Silva, R. L.

2010-07-01

This work describes a metrological activity determination of 124Sb, which can be used as radiotracer, applying gamma spectrometry methods with hyper pure germanium detector and efficiency curves. This isotope with good activity and high radionuclidic purity is employed in the form of meglumine antimoniate (Glucantime) or sodium stibogluconate (Pentostam) to treat leishmaniasis. 124Sb is also applied in animal organ distribution studies to solve some questions in pharmacology. 124Sb decays by β-emission and it produces several photons (X and gamma rays) with energy varying from 27 to 2700 keV. Efficiency curves to measure point 124Sb solid sources were obtained from a 166mHo standard that is a multi-gamma reference source. These curves depend on radiation energy, sample geometry, photon attenuation, dead time and sample-detector position. Results for activity determination of 124Sb samples using efficiency curves and a high purity coaxial germanium detector were consistent in different counting geometries. Also uncertainties of about 2% ( k=2) were obtained.

Rapid Bead-Based Antimicrobial Susceptibility Testing by Optical Diffusometry

PubMed Central

Chung, Chih-Yao; Wang, Jhih-Cheng; Chuang, Han-Sheng

2016-01-01

This study combined optical diffusometry and bead-based immunoassays to develop a novel technique for quantifying the growth of specific microorganisms and achieving rapid AST. Diffusivity rises when live bacteria attach to particles, resulting in additional energy from motile microorganisms. However, when UV-sterilized (dead) bacteria attach to particles, diffusivity declines. The experimental data are consistent with the theoretical model predicted according to the equivalent volume diameter. Using this diffusometric platform, the susceptibility of Pseudomonas aeruginosa to the antibiotic gentamicin was tested. The result suggests that the proliferation of bacteria is effectively controlled by gentamicin. This study demonstrated a sensitive (one bacterium on single particles) and time-saving (within 2 h) platform with a small sample volume (~0.5 μL) and a low initial bacteria count (50 CFU per droplet ~ 105 CFU/mL) for quantifying the growth of microorganisms depending on Brownian motion. The technique can be applied further to other bacterial strains and increase the success of treatments against infectious diseases in the near future. PMID:26863001

PID tuning rules for SOPDT systems: review and some new results.

PubMed

Panda, Rames C; Yu, Cheng-Ching; Huang, Hsiao-Ping

2004-04-01

PID controllers are widely used in industries and so many tuning rules have been proposed over the past 50 years that users are often lost in the jungle of tuning formulas. Moreover, unlike PI control, different control laws and structures of implementation further complicate the use of the PID controller. In this work, five different tuning rules are taken for study to control second-order plus dead time systems with wide ranges of damping coefficients and dead time to time constant ratios (D/tau). Four of them are based on IMC design with different types of approximations on dead time and the other on desired closed-loop specifications (i.e., specified forward transfer function). The method of handling dead time in the IMC type of design is important especially for systems with large D/tau ratios. A systematic approach was followed to evaluate the performance of controllers. The regions of applicability of suitable tuning rules are highlighted and recommendations are also given. It turns out that IMC designed with the Maclaurin series expansion type PID is a better choice for both set point and load changes for systems with D/tau greater than 1. For systems with D/tau less than 1, the desired closed-loop specification approach is favored.

The politics of grief and continuing bonds with the dead: the cases of Maoist China and Wahhabi Islam.

PubMed

Klass, Dennis; Goss, Robert

2003-11-01

The article is a contribution to a cross-cultural theory of grief. It examines the relationship between individual/family continuing bonds with the dead and cultural narratives that legitimize political power. The dead are collective representations (Dirkheim) that mediate the larger culture to individuals and to smaller communities and that reinforce social solidarity and identity. The political question is which collective--family, community, church, party, nation--owns the dead and controls the rituals by which bonds with the dead are maintained or relinquished? The article discusses one historical condition: times of rapid change in power arrangements. Bonds with the dead have a power in individual, family, or tribal life that can threaten the narrative that legitimizes the new political power holders. Ancestor rituals that support identity as a family or tribal member are surpressed and replaced by allegiance to collective representations of the new political order. Two historical examples are given: China under Chairman Mao and the Wahhabi reform in Arabic Islam.

Novel analysis of 4DCT imaging quantifies progressive increases in anatomic dead space during mechanical ventilation in mice.

PubMed

Kim, Elizabeth H; Preissner, Melissa; Carnibella, Richard P; Samarage, Chaminda R; Bennett, Ellen; Diniz, Marcio A; Fouras, Andreas; Zosky, Graeme R; Jones, Heather D

2017-09-01

Increased dead space is an important prognostic marker in early acute respiratory distress syndrome (ARDS) that correlates with mortality. The cause of increased dead space in ARDS has largely been attributed to increased alveolar dead space due to ventilation/perfusion mismatching and shunt. We sought to determine whether anatomic dead space also increases in response to mechanical ventilation. Mice received intratracheal lipopolysaccharide (LPS) or saline and mechanical ventilation (MV). Four-dimensional computed tomography (4DCT) scans were performed at onset of MV and after 5 h of MV. Detailed measurements of airway volumes and lung tidal volumes were performed using image analysis software. The forced oscillation technique was used to obtain measures of airway resistance, tissue damping, and tissue elastance. The ratio of airway volumes to total tidal volume increased significantly in response to 5 h of mechanical ventilation, regardless of LPS exposure, and airways demonstrated significant variation in volumes over the respiratory cycle. These findings were associated with an increase in tissue elastance (decreased lung compliance) but without changes in tidal volumes. Airway volumes increased over time with exposure to mechanical ventilation without a concomitant increase in tidal volumes. These findings suggest that anatomic dead space fraction increases progressively with exposure to positive pressure ventilation and may represent a pathological process. NEW & NOTEWORTHY We demonstrate that anatomic dead space ventilation increases significantly over time in mice in response to mechanical ventilation. The novel functional lung-imaging techniques applied here yield sensitive measures of airway volumes that may have wide applications. Copyright © 2017 the American Physiological Society.

Biosorption Potential of Bacillus salmalaya Strain 139SI for Removal of Cr(VI) from Aqueous Solution.

PubMed

Dadrasnia, Arezoo; Chuan Wei, Kelvin Swee; Shahsavari, Nasser; Azirun, Mohd Sofian; Ismail, Salmah

2015-12-03

The present study investigated the biosorption capacity of live and dead cells of a novel Bacillus strain for chromium. The optimum biosorption condition was evaluated in various analytical parameters, including initial concentration of chromium, pH, and contact time. The Langmuir isotherm model showed an enhanced fit to the equilibrium data. Live and dead biomasses followed the monolayer biosorption of the active surface sites. The maximum biosorption capacity was 20.35 mg/g at 25 °C, with pH 3 and contact time of 50 min. Strain 139SI was an excellent host to the hexavalent chromium. The biosorption kinetics of chromium in the dead and live cells of Bacillus salmalaya (B. salmalaya) 139SI followed the pseudo second-order mechanism. Scanning electron microscopy and fourier transform infrared indicated significant influence of the dead cells on the biosorption of chromium based on cell morphological changes. Approximately 92% and 70% desorption efficiencies were achieved using dead and live cells, respectively. These findings demonstrated the high sorption capacity of dead biomasses of B. salmalaya 139SI in the biosorption process. Thermodynamic evaluation (ΔG⁰, ΔH⁰, and ΔS⁰) indicated that the mechanism of Cr(VI) adsorption is endothermic; that is, chemisorption. Results indicated that chromium accumulation occurred in the cell wall of B. salmalaya 139SI rather than intracellular accumulation.

Biosorption Potential of Bacillus salmalaya Strain 139SI for Removal of Cr(VI) from Aqueous Solution

PubMed Central

Dadrasnia, Arezoo; Chuan Wei, Kelvin Swee; Shahsavari, Nasser; Azirun, Mohd Sofian; Ismail, Salmah

2015-01-01

The present study investigated the biosorption capacity of live and dead cells of a novel Bacillus strain for chromium. The optimum biosorption condition was evaluated in various analytical parameters, including initial concentration of chromium, pH, and contact time. The Langmuir isotherm model showed an enhanced fit to the equilibrium data. Live and dead biomasses followed the monolayer biosorption of the active surface sites. The maximum biosorption capacity was 20.35 mg/g at 25 °C, with pH 3 and contact time of 50 min. Strain 139SI was an excellent host to the hexavalent chromium. The biosorption kinetics of chromium in the dead and live cells of Bacillus salmalaya (B. salmalaya) 139SI followed the pseudo second-order mechanism. Scanning electron microscopy and fourier transform infrared indicated significant influence of the dead cells on the biosorption of chromium based on cell morphological changes. Approximately 92% and 70% desorption efficiencies were achieved using dead and live cells, respectively. These findings demonstrated the high sorption capacity of dead biomasses of B. salmalaya 139SI in the biosorption process. Thermodynamic evaluation (ΔG0, ΔH0, and ΔS0) indicated that the mechanism of Cr(VI) adsorption is endothermic; that is, chemisorption. Results indicated that chromium accumulation occurred in the cell wall of B. salmalaya 139SI rather than intracellular accumulation. PMID:26633454

Biocompatibility of austenite and martensite phases in NiTi-based alloys

NASA Astrophysics Data System (ADS)

Danilov, A.; Kapanen, A.; Kujala, S.; Saaranen, J.; Ryhänen, J.; Pramila, A.; Jämsä, T.; Tuukkanen, J.

2003-10-01

The effect of surface phase composition on the biocompatibility of NiTi-based shape memory alloys was studied. The biocompatibility characteristics of parent β-phase (austenite) in binary NiTi and of martensite in ternary NiTiCu alloys after similar surface mechanical treatment were compared. The martensitic phase as a result of surface mechanical treatment (strain-induced martensite) was shown to decrease the biocompatibility of material in comparison to fully austenite state. The cytotoxicity (amount of dead cells / 1000 cells) and cell attachent (paxillin count / frame) were found to be linear functions of structural stresses in austenite.

On the game of life: population and its diversity

NASA Astrophysics Data System (ADS)

Sales, T. M.; Garcia, J. B. C.; Jyh, T. I.; Ren, T. I.; Gomes, M. A. F.

1993-08-01

One of the most important features of biological life in all levels is its astounding diversity. In this work we study the well-known game “Life” due to Conway analysing the statistics of cluster population, N( t), and cluster diversity, D( t). We have performed simulations on “Life” for dimensions d = 1 and 2 starting with an uncorrelated distribution of live and dead sites at t = 0. For d = 2 we study the effect of different neighbourhood relations in identifying and counting clusters. An interesting scaling relation connecting the maxima of N( t) and D( t) is found.

Surface Bacterial-Spore Assay Using Tb3+/DPA Luminescence

NASA Technical Reports Server (NTRS)

Ponce, Adrian

2007-01-01

Equipment and a method for rapidly assaying solid surfaces for contamination by bacterial spores are undergoing development. The method would yield a total (nonviable plus viable) spore count of a surface within minutes and a viable-spore count in about one hour. In this method, spores would be collected from a surface by use of a transparent polymeric tape coated on one side with a polymeric adhesive that would be permeated with one or more reagent(s) for detection of spores by use of visible luminescence. The sticky side of the tape would be pressed against a surface to be assayed, then the tape with captured spores would be placed in a reader that illuminates the sample with ultraviolet light and counts the green luminescence spots under a microscope to quantify the number of bacterial spores per unit area. The visible luminescence spots seen through the microscope would be counted to determine the concentration of spores on the surface. This method is based on the chemical and physical principles of methods described in several prior NASA Tech Briefs articles, including Live/Dead Spore Assay Using DPA-Triggered Tb Luminescence (NPO-30444), Vol. 27, No. 3 (March 2003), page 7a. To recapitulate: The basic idea is to exploit the observations that (1) dipicolinic acid (DPA) is present naturally only in bacterial spores; and (2) when bound to Tb3+ ions, DPA triggers intense green luminescence of the ions under ultraviolet excitation; (3) DPA can be released from the viable spores by using L-alanine to make them germinate; and (4) by autoclaving, microwaving, or sonicating the sample, one can cause all the spores (non-viable as well as viable) to release their DPA. One candidate material for use as the adhesive in the present method is polydimethysiloxane (PDMS). In one variant of the method for obtaining counts of all (viable and nonviable) spores the PDMS would be doped with TbCl3. After collection of a sample, the spores immobilized on the sticky tape surface would be lysed by heating or microwaving to release their DPA. Tb3+ ions from the TbCl3 would become bound to the released DPA. The tape would then be irradiated with ultraviolet and examined as described above. In another variant of the method - for obtaining counts of viable spores only - the PDMS would be doped with L-alanine in addition to TbCl3. As now envisioned, a fully developed apparatus for implementing this method would include a pulsed source of ultraviolet light and a time-gated electronic camera to record the images seen through the microscope during a prescribed exposure interval at a prescribed short time after an ultraviolet pulse. As in the method of the second-mentioned prior article, the pulsing and time-gating would be used to discriminate between the longer-lived Tb3+/DPA luminescence and the shorter-lived background luminescence in the same wavelength range. In a time-gated image, the bright luminescence from bacterial spores could easily be seen against a dark background.

Effects of hydrogen peroxide on vestibular hair cells in the guinea pig: importance of cell membrane impairment preceding cell death.

PubMed

Tanigawa, Tohru; Tanaka, Hirokazu; Hayashi, Ken; Nakayama, Meiho; Iwasaki, Satoshi; Banno, Shinya; Takumida, Masaya; Brodie, Hirally; Inafuku, Shigeru

2008-11-01

Our findings indicate that oxidative stress induces morphological changes in vestibular hair cells and subsequently leads to cell death after 2.5 h. The aim of this study was to confirm the direct effects of oxidative stress on vestibular hair cells. Vestibular hair cells isolated from guinea pigs were loaded with 1 or 10 mM H2O2, and morphological changes were observed. In addition, in a viability/cytotoxicity assay system, the numbers of dead cells in isolated cristae ampullares were counted 1, 3, and 5 h after loading with H2O2 or artificial perilymph (control). Reactive oxygen, in the form of H2O2, directly affects the cell membrane of isolated vestibular hair cells and causes swelling of the cell body, bleb formation, and shortening of the neck region. Morphological changes occur within 30 min after loading with H2O2, but a significant increase in the number of dead cells is noted only after 3 h.

An unusual mortality event in Johnstone River snapping turtles Elseya irwini (Johnstone) in Far North Queensland, Australia.

PubMed

Ariel, E; Freeman, A B; Elliott, E; Wirth, W; Mashkour, N; Scott, J

2017-10-01

An unusual mortality event in Johnstone River snapping turtles (Elseya irwini) in Far North Queensland, Australia, occurred during the summer months of December 2014 and January 2015. We report the data collected during the mortality event, including counts of sick and dead animals, clinical appearance and one necropsy. Moribund animals appeared lethargic with variable degrees of necrotising dermatitis. Postmortem investigation of one freshly dead animal revealed bacterial and fungal involvement in the skin lesions as well as multifocal fibrinous hepatitis and splenitis and necrotising enteritis with vascular thrombosis. Aeromonas hydrophila was isolated from liver, spleen and skin lesions. All samples tested negative for ranavirus, and water and soil testing for environmental contaminants were negative. All affected E. irwini either died or were euthanased and no other species of animals in the river were affected. Aeromonas hydrophila is ubiquitous in the freshwater environment and although it caused septicaemia in the one individual that was submitted for laboratory diagnosis, the primary aetiology of the outbreak may not have been identified. © 2017 Australian Veterinary Association.

Reduction of Endotracheal Tube Connector Dead Space Improves Ventilation: A Bench Test on a Model Lung Simulating an Extremely Low Birth Weight Neonate.

PubMed

Ivanov, Vadim A

2016-02-01

The reduction of instrumental dead space is a recognized approach to preventing ventilation-induced lung injury in premature infants. However, there are no published data regarding the effectiveness of instrumental dead-space reduction in endotracheal tube (ETT) connectors. We tested the impact of the Y-piece/ETT connector pairs with reduced instrumental dead space on CO2 elimination in a model of the premature neonate lung. The standard ETT connector was compared with a low-dead-space ETT connector and with a standard connector equipped with an insert. We compared the setups by measuring the CO2 elimination rate in an artificial lung ventilated via the connectors. The lung was connected to a ventilator via a standard circuit, a 2.5-mm ETT, and one of the connectors under investigation. The ventilator was run in volume-controlled continuous mandatory ventilation mode. The low-dead-space ETT connector/Y-piece and insert-equipped standard connector/Y-piece pairs had instrumental dead space reduced by 36 and 67%, respectively. With set tidal volumes (VT) of 2.5, 5, and 10 mL, in comparison with the standard ETT connector, the low-dead-space connector reduced CO2 elimination time by 4.5% (P < .05), 4.4% (P < .01), and 7.1% (not significant), respectively. The insert-equipped standard connector reduced CO2 elimination time by 13.5, 25.1, and 16.1% (all P < .01). The low-dead-space connector increased inspiratory resistance by 17.8% (P < .01), 9.6% (P < .05), and 5.0% (not significant); the insert-equipped standard connector increased inspiratory resistance by 9.1, 8.4, and 5.9% (all not significant). The low-dead-space connector decreased expiratory resistance by 6.8% (P < .01) and 1.8% (not significant) and increased it by 1.4% (not significant); the insert-equipped standard connector decreased expiratory resistance by 1.5 and 1% and increased it by 1% (all not significant). The low-dead-space connector increased work of breathing by 4.7% (P < .01), 3.8% (P < .01), and 2.5% (not significant); the insert-equipped standard connector increased it by 0.8% (not significant), 2.5% (P < .01), and 2.8% (P < .01). Both methods of instrumental dead-space reduction led to improvements in artificial lung ventilation. Negative effects on resistance and work of breathing appeared minimal. Further testing in vivo should be performed to confirm the lung model results and, if successful, translated into clinical practice. Copyright © 2016 by Daedalus Enterprises.

Pulmonary Dead Space Fraction and Extubation Success in Children After Cardiac Surgery.

PubMed

Devor, Renee L; Kang, Paul; Wellnitz, Chasity; Nigro, John J; Velez, Daniel A; Willis, Brigham C

2018-04-01

1) Determine the correlation between pulmonary dead space fraction and extubation success in postoperative pediatric cardiac patients; and 2) document the natural history of pulmonary dead space fractions, dynamic compliance, and airway resistance during the first 72 hours postoperatively in postoperative pediatric cardiac patients. A retrospective chart review. Cardiac ICU in a quaternary care free-standing children's hospital. Twenty-nine with balanced single ventricle physiology, 61 with two ventricle physiology. None. We collected data for all pediatric patients undergoing congenital cardiac surgery over a 14-month period during the first 72 hours postoperatively as well as prior to extubation. Overall, patients with successful extubations had lower preextubation dead space fractions and shorter lengths of stay. Single ventricle patients had higher initial postoperative and preextubation dead space fractions. Two-ventricle physiology patients had higher extubation failure rates if the preextubation dead space fraction was greater than 0.5, whereas single ventricle patients had similar extubation failure rates whether preextubation dead space fractions were less than or equal to 0.5 or greater than 0.5. Additionally, increasing initial dead space fraction values predicted prolonged mechanical ventilation times. Airway resistance and dynamic compliance were similar between those with successful extubations and those who failed. Initial postoperative dead space fraction correlates with the length of mechanical ventilation in two ventricle patients but not in single ventricle patients. Lower preextubation dead space fractions are a strong predictor of successful extubation in two ventricle patients after cardiac surgery, but may not be as useful in single ventricle patients.

Are major reductions in new HIV infections possible with people who inject drugs? The case for low dead-space syringes in highly affected countries.

PubMed

Zule, William A; Cross, Harry E; Stover, John; Pretorius, Carel

2013-01-01

Circumstantial evidence from laboratory studies, mathematical models, ecological studies and bio behavioural surveys, suggests that injection-related HIV epidemics may be averted or reversed if people who inject drugs (PWID) switch from using high dead-space to using low dead-space syringes. In laboratory experiments that simulated the injection process and rinsing with water, low dead space syringes retained 1000 times less blood than high dead space syringes. In mathematical models, switching PWID from high dead space to low dead space syringes prevents or reverses injection-related HIV epidemics. No one knows if such an intervention is feasible or what effect it would have on HIV transmission among PWID. Feasibility studies and randomized controlled trials (RCTs) will be needed to answer these questions definitively, but these studies will be very expensive and take years to complete. Rather than waiting for them to be completed, we argue for an approach similar to that used with needle and syringe programs (NSP), which were promoted and implemented before being tested more rigorously. Before implementation, rapid assessments that involve PWID will need to be conducted to ensure buy-in from PWID and other local stakeholders. This commentary summarizes the existing evidence regarding the protective effects of low dead space syringes and estimates potential impacts on HIV transmission; it describes potential barriers to transitioning PWID from high dead space to low dead space needles and syringes; and it presents strategies for overcoming these barriers. Copyright © 2012 Elsevier B.V. All rights reserved.

Effects of detector dead-time on quantitative analyses involving boron and multi-hit detection events in atom probe tomography.

PubMed

Meisenkothen, Frederick; Steel, Eric B; Prosa, Ty J; Henry, Karen T; Prakash Kolli, R

2015-12-01

In atom probe tomography (APT), some elements tend to field evaporate preferentially in multi-hit detection events. Boron (B) is one such element. It is thought that a large fraction of the B signal may be lost during data acquisition and is not reported in the mass spectrum or in the 3-D APT reconstruction. Understanding the relationship between the field evaporation behavior of B and the limitations for detecting multi-hit events can provide insight into the signal loss mechanism for B and may suggest ways to improve B detection accuracy. The present work reports data for nominally pure B and for B-implanted silicon (Si) (NIST-SRM2137) at dose levels two-orders of magnitude lower than previously studied by Da Costa, et al. in 2012. Boron concentration profiles collected from SRM2137 specimens qualitatively confirmed a signal loss mechanism is at work in laser pulsed atom probe measurements of B in Si. Ion correlation analysis was used to graphically demonstrate that the detector dead-time results in few same isotope, same charge-state (SISCS) ion pairs being properly recorded in the multi-hit data, explaining why B is consistently under-represented in quantitative analyses. Given the important role of detector dead-time as a signal loss mechanism, the results from three different methods of estimating the detector dead-time are presented. The findings of this study apply to all quantitative analyses that involve multi-hit data, but the dead-time will have the greatest effect on the elements that have a significant quantity of ions detected in multi-hit events. Published by Elsevier B.V.

MONITORING RANAVIRUS-ASSOCIATED MORTALITY IN A DUTCH HEATHLAND IN THE AFTERMATH OF A RANAVIRUS DISEASE OUTBREAK.

PubMed

Sluijs, Annemarieke Spitzen-van der; van den Broek, Jan; Kik, Marja; Martel, An; Janse, Jöran; van Asten, Fons; Pasmans, Frank; Gröne, Andrea; Rijks, Jolianne M

2016-10-01

The ranaviruses are an emerging group of viruses that infect amphibians, fish, and reptiles. Although ranaviruses have not been linked to extinctions, emergence in amphibian communities has resulted in population declines for some species. We present the results of ranavirus-associated mortality in a Dutch national park in the aftermath of an outbreak associated with a common midwife toad virus (CMTV)-like ranavirus. We monitored five bodies of water across Dwingelderveld National Park, the Netherlands, in 2011-13. Dead and live amphibians were counted weekly July-September and every 2 wk in June and October. Dead amphibians were collected and tested for ranavirus infection. In addition, we measured biologic, chemical, and physical site characteristics to test for a correlation with ranavirus-associated mortality. Ranavirus infection was widespread in our study area and we observed nearly continuous presence of dead, ranavirus-infected amphibians in the presence of asymptomatic, live amphibians throughout our study. Fatalities occurred in larval, subadult, and adult amphibians. Ranavirus infection prevalence (based on fatal cases) was significantly associated with increasing fractions of adults and subadults compared to juveniles and larvae in the population, but was unrelated to any other measured site characteristics. Our findings showed that a CMTV-like ranavirus can persist long term in an ecosystem, affecting a diversity of amphibian species and life stages for a prolonged period. This study illustrates the importance of monitoring the modes of spread for ranaviruses and their impact on amphibian populations.

Optimization of integrated impeller mixer via radiotracer experiments.

PubMed

Othman, N; Kamarudin, S K; Takriff, M S; Rosli, M I; Engku Chik, E M F; Adnan, M A K

2014-01-01

Radiotracer experiments are carried out in order to determine the mean residence time (MRT) as well as percentage of dead zone, V dead (%), in an integrated mixer consisting of Rushton and pitched blade turbine (PBT). Conventionally, optimization was performed by varying one parameter and others were held constant (OFAT) which lead to enormous number of experiments. Thus, in this study, a 4-factor 3-level Taguchi L9 orthogonal array was introduced to obtain an accurate optimization of mixing efficiency with minimal number of experiments. This paper describes the optimal conditions of four process parameters, namely, impeller speed, impeller clearance, type of impeller, and sampling time, in obtaining MRT and V dead (%) using radiotracer experiments. The optimum conditions for the experiments were 100 rpm impeller speed, 50 mm impeller clearance, Type A mixer, and 900 s sampling time to reach optimization.

A Delayed Neutron Counting System for the Analysis of Special Nuclear Materials

NASA Astrophysics Data System (ADS)

Sellers, Madison Theresa

Nuclear forensic analysis is a modem science that uses numerous analytical techniques to identify and attribute nuclear materials in the event of a nuclear explosion, radiological terrorist attack or the interception of illicit nuclear material smuggling. The Canadian Department of National Defence has participated in recent international exercises that have highlighted the Nation's requirement to develop nuclear forensics expertise, protocol and capabilities, specifically pertaining to the analysis of special nuclear materials (SNM). A delayed neutron counting (DNC) system has been designed and established at the Royal Military College of Canada (RMC) to enhance the Government's SNM analysis capabilities. This analytical technique complements those already at RMC by providing a rapid and non-destructive method for the analysis of the fissile isotopes of both uranium (U) and plutonium (Pu). The SLOWPOKE-2 reactor at RMC produces a predominately thermal neutron flux. These neutrons induce fission in the SNM isotopes 233U, 235U and 239Pu releasing prompt fast neutrons, energy and radioactive fission fragments. Some of these fission fragments undergo beta - decay and subsequently emit neutrons, which can be recorded by an array of sensitive 3He detectors. The significant time period between the fission process and the release of these neutrons results in their identification as 'delayed neutrons'. The recorded neutron spectrum varies with time and the count rate curve is unique to each fissile isotope. In-house software, developed by this project, can analyze this delayed neutron curve and provides the fissile mass in the sample. Extensive characterization of the DNC system has been performed with natural U samples with 235 U content ranging from 2--7 microg. The system efficiency and dead time behaviour determined by the natural uranium sample analyses were validated by depleted uranium samples with similar quantities of 235 U resulting in a typical relative error of 3.6%. The system has accurately determined 235U content over three orders of magnitude with 235U amounts as low as 10 ng. The results have also been proven to be independent of small variations in total analyte volume and geometry, indicating that it is an ideal technique for the analysis of samples containing SNM in a variety of different matrices. The Analytical Sciences Group at RMC plans to continue DNC system development to include 233U and 239pu analysis and mixtures of SNM isotopes. Keywords: delayed neutron counting, special nuclear materials, nuclear forensics.

Neural-adaptive control of single-master-multiple-slaves teleoperation for coordinated multiple mobile manipulators with time-varying communication delays and input uncertainties.

PubMed

Li, Zhijun; Su, Chun-Yi

2013-09-01

In this paper, adaptive neural network control is investigated for single-master-multiple-slaves teleoperation in consideration of time delays and input dead-zone uncertainties for multiple mobile manipulators carrying a common object in a cooperative manner. Firstly, concise dynamics of teleoperation systems consisting of a single master robot, multiple coordinated slave robots, and the object are developed in the task space. To handle asymmetric time-varying delays in communication channels and unknown asymmetric input dead zones, the nonlinear dynamics of the teleoperation system are transformed into two subsystems through feedback linearization: local master or slave dynamics including the unknown input dead zones and delayed dynamics for the purpose of synchronization. Then, a model reference neural network control strategy based on linear matrix inequalities (LMI) and adaptive techniques is proposed. The developed control approach ensures that the defined tracking errors converge to zero whereas the coordination internal force errors remain bounded and can be made arbitrarily small. Throughout this paper, stability analysis is performed via explicit Lyapunov techniques under specific LMI conditions. The proposed adaptive neural network control scheme is robust against motion disturbances, parametric uncertainties, time-varying delays, and input dead zones, which is validated by simulation studies.

Biofilm formation on stainless steel and gold wires for bonded retainers in vitro and in vivo and their susceptibility to oral antimicrobials.

PubMed

Jongsma, Marije A; Pelser, Floris D H; van der Mei, Henny C; Atema-Smit, Jelly; van de Belt-Gritter, Betsy; Busscher, Henk J; Ren, Yijin

2013-05-01

Bonded retainers are used in orthodontics to maintain treatment result. Retention wires are prone to biofilm formation and cause gingival recession, bleeding on probing and increased pocket depths near bonded retainers. In this study, we compare in vitro and in vivo biofilm formation on different wires used for bonded retainers and the susceptibility of in vitro biofilms to oral antimicrobials. Orthodontic wires were exposed to saliva, and in vitro biofilm formation was evaluated using plate counting and live/dead staining, together with effects of exposure to toothpaste slurry alone or followed by antimicrobial mouthrinse application. Wires were also placed intra-orally for 72 h in human volunteers and undisturbed biofilm formation was compared by plate counting and live/dead staining, as well as by denaturing gradient gel electrophoresis for compositional differences in biofilms. Single-strand wires attracted only slightly less biofilm in vitro than multi-strand wires. Biofilms on stainless steel single-strand wires however, were much more susceptible to antimicrobials from toothpaste slurries and mouthrinses than on single-strand gold wires and biofilms on multi-strand wires. Also, in vivo significantly less biofilm was found on single-strand than on multi-strand wires. Microbial composition of biofilms was more dependent on the volunteer involved than on wire type. Biofilms on single-strand stainless steel wires attract less biofilm in vitro and are more susceptible to antimicrobials than on multi-strand wires. Also in vivo, single-strand wires attract less biofilm than multi-strand ones. Use of single-strand wires is preferred over multi-strand wires, not because they attract less biofilm, but because biofilms on single-strand wires are not protected against antimicrobials as in crevices and niches as on multi-strand wires.

Water Quality Modeling in the Dead End Sections of Drinking Water Distribution Networks

EPA Science Inventory

Dead-end sections of drinking water distribution networks are known to be problematic zones in terms of water quality degradation. Extended residence time due to water stagnation leads to rapid reduction of disinfectant residuals allowing the regrowth of microbial pathogens. Wate...

A Micro Fluorescent Activated Cell Sorter for Astrobiology Applications

NASA Technical Reports Server (NTRS)

Platt, Donald W.; Hoover, Richard B.

2009-01-01

A micro-scale Fluorescent Activated Cell Sorter (microFACS) for astrobiology applications is under development. This device is designed to have a footprint of 7 cm x 7 cm x 4 cm and allow live-dead counts and sorting of cells that have fluorescent characteristics from staining. The FACS system takes advantage of microfluidics to create a cell sorter that can fit in the palm of the hand. A micron-scale channel allows cells to pass by a blue diode which causes emission of marker-expressed cells which are detected by a filtered photodetector. A small microcontroller then counts cells and operates high speed valves to select which chamber the cell is collected in (a collection chamber or a waste chamber). Cells with the expressed characteristic will be collected in the collection chamber. This system has been built and is currently being tested. We are also designing a system with integrated MEMS-based pumps and valves for a small and compact unit to fly on small satellite-based biology experiments.

Fluoro-luminometric real-time measurement of bacterial viability and killing.

PubMed

Lehtinen, Janne; Virta, Marko; Lilius, Esa Matti

2003-10-01

The viability and killing of Escherichia coli was measured on a real-time basis using a fluoro-luminometric device, which allows successive measurements of fluorescence and bioluminescence without user intervention. Bacteria were made fluorescent and bioluminescent by expression of gfp and insect luciferase (lucFF) genes. The green fluorescent protein (GFP) is a highly fluorescent, extremely stable protein, which accumulates in cells during growth, and therefore the measured fluorescence signal was proportional to the total number of cells. The luciferase reaction is dependent of ATP produced by living cells, so that the bioluminescence level was a direct measure of the viable cells. In contrast to the bacterial luciferase, the insect luciferase uses a water-soluble and nonvolatile substrate, which makes automated multi-well microplate assay possible. For the validation of the assay, the proportion of living and dead cell populations was experimentally modified by incubating E. coli cells in the presence of various ethanol concentrations. Bacterial viability and killing measured by a fluoro-luminometric assay correlated fairly well with the reference methods: conventional plate counting, optical density measurement and various flow cytometric analyses. The real-time assay described here allows following the changes in bacterial cultures and assessing the bactericidal and other effects of various chemical, immunological and physical agents simultaneously in large numbers of samples.

Rigor mortis in an unusual position: Forensic considerations.

PubMed

D'Souza, Deepak H; Harish, S; Rajesh, M; Kiran, J

2011-07-01

We report a case in which the dead body was found with rigor mortis in an unusual position. The dead body was lying on its back with limbs raised, defying gravity. Direction of the salivary stains on the face was also defying the gravity. We opined that the scene of occurrence of crime is unlikely to be the final place where the dead body was found. The clues were revealing a homicidal offence and an attempt to destroy the evidence. The forensic use of 'rigor mortis in an unusual position' is in furthering the investigations, and the scientific confirmation of two facts - the scene of death (occurrence) is different from the scene of disposal of dead body, and time gap between the two places.

Rigor mortis in an unusual position: Forensic considerations

PubMed Central

D’Souza, Deepak H; Harish, S; Rajesh, M.; Kiran, J

2011-01-01

We report a case in which the dead body was found with rigor mortis in an unusual position. The dead body was lying on its back with limbs raised, defying gravity. Direction of the salivary stains on the face was also defying the gravity. We opined that the scene of occurrence of crime is unlikely to be the final place where the dead body was found. The clues were revealing a homicidal offence and an attempt to destroy the evidence. The forensic use of ‘rigor mortis in an unusual position’ is in furthering the investigations, and the scientific confirmation of two facts - the scene of death (occurrence) is different from the scene of disposal of dead body, and time gap between the two places. PMID:23776792

Hydroxyapatite promotes superior keratocyte adhesion and proliferation in comparison with current keratoprosthesis skirt materials.

PubMed

Mehta, J S; Futter, C E; Sandeman, S R; Faragher, R G A F; Hing, K A; Tanner, K E; Allan, B D S

2005-10-01

Published clinical series suggest the osteoodontokeratoprosthesis (OOKP) may have a lower extrusion rate than current synthetic keratoprostheses. The OOKP is anchored in the eye wall by autologous tooth. The authors' aim was to compare adhesion, proliferation, and morphology for telomerase transformed keratocytes seeded on calcium hydroxyapatite (the principal mineral constituent of tooth) and materials used in the anchoring elements of commercially available synthetic keratoprostheses. Test materials were hydroxyapatite, polytetrafluoroethylene (PTFE), polyhydroxyethyl methacrylate (HEMA), and glass (control). Cell adhesion and viability were quantified at 4 hours, 24 hours, and 1 week using a calcein-AM/EthD-1 viability/cytotoxicity assay. Focal contact expression and cytoskeletal organisation were studied at 24 hours by confocal microscopy with immunoflourescent labelling. Further studies of cell morphology were performed using light and scanning electron microscopy. Live cell counts were significantly greater on hydroxyapatite surfaces at each time point (p<0.04). Dead cell counts were significantly higher for PTFE at 7 days (p<0.002). ss(1) integrin expression was highest on hydroxyapatite. Adhesion structures were well expressed in flat, spread out keratocytes on both HA and glass. Keratocytes tended to be thinner and spindle shaped on PTFE. The relatively few keratocytes visible on HEMA test surfaces were rounded and poorly adherent. Keratocyte adhesion, spreading, and viability on hydroxyapatite test surfaces is superior to that seen on PTFE and HEMA. Improving the initial cell adhesion environment in the skirt element of keratoprostheses may enhance tissue integration and reduce device failure rates.

Bleaching response of Symbiodinium (zooxanthellae): determination by flow cytometry.

PubMed

Lee, Co Sin; Yeo, Yin Sheng Wilson; Sin, Tsai Min

2012-10-01

Coral bleaching is of increasing concern to reef management and stakeholders. Thus far, quantification of coral bleaching tends to be heavily reliant on the enumeration of zooxanthellae, with less emphasis on assessment of photosynthetic or physiological condition, these being often assessed separately by techniques such as liquid chromatography. Traditional methods of enumeration using microscopy are time consuming, subjected to low precision and great observer error. In this study, we presented a method for the distinction of physoiological condition and rapid enumeration of zooxanthellae using flow cytometry (FCM). Microscopy verified that healthy looking/live versus damaged/dead zooxanthellae could be reliably and objectively distinguished and counted by FCM on the basis of red and green fluorescence and light scatter. Excellent correlations were also determined between FCM and microscopy estimates of cell concentrations of fresh zooxanthellae isolates from Pocillopora damicornis. The relative intensities of chlorophyll and β-carotene fluorescences were shown to be important in understanding the results of increased cell counts in freshly isolated zooxanthellae experimentally exposed to high temperatures (34, 36, and 38°C) over 24 h, with ambient temperature (29°C) used as controls. The ability to simultaneously identify and enumerate subpopulations of different physiological states in the same sample provides an enormous advantage in not just determining bleaching responses, but elucidating adaptive response and mechanisms for tolerance. Therefore, this approach might provide a rapid, convenient, and reproducible methodology for climate change studies and reef management programs. Copyright © 2012 International Society for Advancement of Cytometry.

Water Quality Modeling in the Dead End Sections of Drinking Water Distribution Networks -journal article

EPA Science Inventory

Dead-end sections of drinking water distribution networks are known to be problematic zones in terms of water quality degradation. Extended residence time due to water stagnation leads to rapid reduction of disinfectant residuals allowing the regrowth of microbial pathogens. Wate...

[Antibacterial effect of self-etching adhesive systems on Streptococcus mutans].

PubMed

Zhang, Lu; Yuan, Chong-yang; Tian, Fu-cong; Wang, Xiao-yan; Gao, Xue-jun

2016-02-18

To investigate the antibacterial effect of different self-etching adhesive systems against Streptococcus mutans (S. mutans). Six reagents Clearfil(TM) SE Bond primer (SP), Clearfil(TM) SE Bond adhesive (SA),Clearfil(TM) Protect Bond primer (PP), which contained antibacterial monomer methacryloyloxydodecylpyridinium bromide (MDPB), ClearfilTM Protect Bond adhesive (PA), positive control chlorhexidine acetate [CHX, 1% (mass fraction)], and negative control phosphate buffer solution (PBS) were selected. They were mixed with S. mutans for 30 s respectively, then colony-forming units (CFU) were counted after incubated for 48 h on brain heart infusion (BHI) agar medium. The 6 reagents were applied to the sterile paper discs, and distributed onto the BHI agar medium with S. mutans and incubated for 24 h, then the inhibition zones were observed. CHX, PBS, PP, and SP were added on the dentin with artificial caries induced by S. mutans and kept for 30 s, then confocal laser scanning microscope (CLSM) was used to observe the live and dead bacteria after staining. The ratio of live to dead bacteria was calculated. PP+PA and SP+SA were applied on the dentin according to the manual and light cured. S. mutans were incubated on the samples for 2 h, ultrasonically treated and incubated on BHI agar medium for 48 h, then CFU was counted. The data were analyzed by non-parametric analysis and one-way ANOVA. Compared with PBS, the PP, SP, PA, SA and CHX showed the antibacterial effect on free S. mutans (P<0.05); SP and PP showed stronger antibacterial effect than PA, SA and CHX (P<0.05). CHX, SP and PP presented inhibition zones, while PBS, SA and PA did not. Compared with PBS, the CHX, SP and PP could lower the ratio of the live to dead bacteria significantly (P<0.05). Cured self-etching adhesive systems did not show any antibacterial effect on the free S. mutans. The primer of self-etching adhesives Clearfil(TM) SE Bond and Clearfil(TM) Protect Bond showed significant antibacterial effect on free and attached S. mutans. The adhesive only showed antibacterial effect on free S. mutans before light-cured polymerization. After being cured, the self-etching adhesive systems did not show antibacterial effect anymore.

Rapid and direct detection of Invivo kinetics of pathogenic bacterial infection from mouse blood and urine.

PubMed

Gopal, Judy; Lee, Chia-Hsun; Wu, Hui-Fen

2012-06-06

This study demonstrates the first use of matrix assisted laser desorption/ionization mass spectrometry (MALDI-MS) to trace the Invivo infection kinetics of the well known deadly pathogen Staphylococcus aureus in Swiss albino mice. The growth curve of the bacteria from the point of injection (200μL of bacterial suspension (10(8)cfu/mL)) into the mouse blood till mortality (death) was periodically analyzed using the plate counting method and MALDI-MS. Bacterial counts of 10(3)cfu/mL were observed in the log phase of the growth curve in the blood and 10(2)cfu/mL were observed in the urine samples. Death occurred in the log phase of the growth curve, where the bacterial counts showed steady increase. In other cases, the bacteria counts started decreasing after 48h and by 96h the bacteria got totally eliminated from the mouse and these mice survived. Direct MALDI-MS was not feasible for tracking the bacteria in the infected blood. However, ionic liquid 1-Butyl-3-methylimidazolium tetrafluoroborate was successful in enabling bacterial detection amidst the strong blood peaks. But, in the case of the urine analysis, it was observed that direct MALDI-MS was adequate to enable detection. The results obtained prove the efficacy of MALDI-MS for analyzing pathogenic bacteria in clinical samples. This article is part of a Special Issue entitled: Proteomics: The clinical link. Copyright © 2011 Elsevier B.V. All rights reserved.

A novel digital pulse processing architecture for nuclear instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moline, Yoann; Thevenin, Mathieu; Corre, Gwenole

The field of nuclear instrumentation covers a wide range of applications, including counting, spectrometry, pulse shape discrimination and multi-channel coincidence. These applications are the topic of many researches, new algorithms and implementations are constantly proposed thanks to advances in digital signal processing. However, these improvements are not yet implemented in instrumentation devices. This is especially true for neutron-gamma discrimination applications which traditionally use charge comparison method while literature proposes other algorithms based on frequency domain or wavelet theory which show better performances. Another example is pileups which are generally rejected while pileup correction algorithms also exist. These processes are traditionallymore » performed offline due to two issues. The first is the Poissonian characteristic of the signal, composed of random arrival pulses which requires to current architectures to work in data flow. The second is the real-time requirement, which implies losing pulses when the pulse rate is too high. Despite the possibility of treating the pulses independently from each other, current architectures paralyze the acquisition of the signal during the processing of a pulse. This loss is called dead-time. These two issues have led current architectures to use dedicated solutions based on re-configurable components like Field Programmable Gate Arrays (FPGAs) to overcome the need of performance necessary to deal with dead-time. However, dedicated hardware algorithm implementations on re-configurable technologies are complex and time-consuming. For all these reasons, a programmable Digital pulse Processing (DPP) architecture in a high level language such as Cor C++ which can reduce dead-time would be worthwhile for nuclear instrumentation. This would reduce prototyping and test duration by reducing the level of hardware expertise to implement new algorithms. However, today's programmable solutions do not meet the need of performance to operate online and not allow scaling with the increase in the number of measurement channel. That is why an innovative DPP architecture is proposed in this paper. This architecture is able to overcome dead-time while being programmable and is flexible with the number of measurement channel. Proposed architecture is based on an innovative execution model for pulse processing applications which can be summarized as follow. The signal is not composed of pulses only, consequently, pulses processing does not have to operate on the entire signal. Therefore, the first step of our proposal is pulse extraction by the use of dedicated components named pulse extractors. The triggering step can be achieved after the analog-to-digital conversion without any signal shaping or filtering stages. Pileup detection and accurate pulse time stamping are done at this stage. Any application downstream this step can work on adaptive variable-sized array of samples simplifying pulse processing methods. Then, once the data flow is broken, it is possible to distribute pulses on Functional Units (FUs) which perform processing. As the date of each pulse is known, they can be processed individually out-of-order to provide the results. To manage the pulses distribution, a scheduler and an interconnection network are used. pulses are distributed on the first FU which is not busy without congesting the interconnection network. For this reason, the process duration does not result anymore in dead-time if there are enough FUs. FUs are designed to be standalone and to comprises at least a programmable general purpose processor (ARM, Microblaze) allowing the implementation of complex algorithms without any modification of the hardware. An acquisition chain is composed of a succession of algorithms which lead to organize our FUs as a software macro-pipeline, A simple approach consists in assigning one algorithm per FU. Consequently, the global latency becomes the worst latency of algorithms execution on FU. Moreover, as algorithms are executed locally - i.e. on a FU - this approach limits shared memory requirement. To handle multichannel, we propose FUs sharing, this approach maximize the chance to find a non-busy FU to process an incoming pulse. This is possible since each channel receive random event independently, the pulse extractors associated to them do not necessarily need to access simultaneously to all Computing resources at the same time to distribute their pulses. The major contribution of this paper is the proposition of an execution model and its associated hardware programmable architecture for digital pulse processing that can handle multiple acquisition channels while maintaining the scalability thanks to the use of shared resources. This execution model and associated architecture are validated by simulation of a cycle accurate architecture SystemC model. Proposed architecture shows promising results in terms of scalability while maintaining zero dead-time. This work also permit the sizing of hardware resources requirement required for a predefined set of applications. Future work will focus on the interconnection network and a scheduling policy that can exploit the variable-length of pulses. Then, the hardware implementation of this architecture will be performed and tested for a representative set of application.« less

Online Robot Dead Reckoning Localization Using Maximum Relative Entropy Optimization With Model Constraints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Urniezius, Renaldas

2011-03-14

The principle of Maximum relative Entropy optimization was analyzed for dead reckoning localization of a rigid body when observation data of two attached accelerometers was collected. Model constraints were derived from the relationships between the sensors. The experiment's results confirmed that accelerometers each axis' noise can be successfully filtered utilizing dependency between channels and the dependency between time series data. Dependency between channels was used for a priori calculation, and a posteriori distribution was derived utilizing dependency between time series data. There was revisited data of autocalibration experiment by removing the initial assumption that instantaneous rotation axis of a rigidmore » body was known. Performance results confirmed that such an approach could be used for online dead reckoning localization.« less

Airborne laser scanning based quantification of dead-ice melting in recently deglaciated terrain

NASA Astrophysics Data System (ADS)

Klug, C.; Sailer, R.; Schümberg, M.; Stötter, J.

2012-04-01

Dead-ice is explained as stagnant glacial ice, not influenced by glacier flow anymore. Whenever glaciers have negative mass balances and an accumulation of debris-cover on the surface, dead-ice may form. Although, there are numerous conceptual process-sediment-landform models for the melt-out of dead-ice bodies and areas of dead-ice environments at glacier margins are easily accessible, just a few quantitative studies of dead-ice melting have been carried out so far. Processes and rates of dead-ice melting are commonly believed to be controlled by climate and debris-cover properties, but there is still a lack of knowledge about this fact. This study has a focus on the quantification of process induced volumetric changes caused by dead-ice melting. The research for this project was conducted at Hintereisferner (Ötztal Alps, Austria), Gepatschferner (Ötztal Alps, Austria) and Schrankar (Stubai Alps, Austria), areas for which a good data basis of ALS (Airborne Laser Scanning) measurements is available. 'Hintereisferner' can be characterized as a typical high alpine environment in mid-latitudes, which ranges between approximately 2250 m and 3740 m a.s.l.. The Hintereisferner region has been investigated intensively since many decades. Two dead ice bodies at the orographic right side and one at the orographic left side of the Hintereisferner glacier terminus (approx. at 2500 m to 2550 m a.s.l.) were identified. Since 2001, ALS measurements have been carried out regularly at Hintereisferner resulting in a unique data record of 21 ALS flight campaigns, allowing long-term explorations of the two dead-ice areas. The second study area of 'Gepatschferner' in the Kaunertal ranges between 2060 m and 3520 m a.s.l. and is the second largest glacier of Austria. Near the glacier tongue at the orographic right side a significant dead ice body has formed. The ALS data used for quantification include a period of time of 4 years (2006 - 2010). 'Schrankar' is located in the Western Stubai Alps in a north to south aligned valley, with 12 rockglaciers of different activities between elevations of 2400 m and 2800 m a.s.l.. Beside the rockglaciers, a big dead ice body (approx. at 2800 m to 2850 m a.s.l.) next to the terminus of the southern Schrankarferner was identified. For the quantification of dead-ice melting, ALS data was used from 2006 - 2009. Additionally, a time series of digital elevation models (DEM) derived from aerial images of different periods (1953 -2003) were integrated in the analysis. In recent years, high-accuracy DEMs from ALS altimetry are emerging as an additional data source to existing field measurements. We present inter annual and annual trends of topographic changes caused by dead-ice melting. These trends are determined from multitemporal DEM differencing. The DEMs are generated from aerial images and ALS data. First results on the three dead-ice bodies of Hintereisferner show significant changes (-0.48 m and -2.24 m respectively per year). The derived melt rates are discussed, summarized and assessed in relation to climate parameters, like mean annual air temperature, mean summer air temperature, mean annual precipitation, mean summer precipitation, and annual sum of positive degree days.

HST FUV monitoring of TW Hya

NASA Astrophysics Data System (ADS)

Guenther, Hans; Brickhouse, N. S.; Dupree, A. K.; Luna, G.; Schneider, P. C.; Wolk, S. J.

2014-01-01

Classical T Tauri stars (CTTS) show strong, broad and asymmetric FUV emission lines. Neither the width, nor the line profile is understood. Likely, different mechanisms influence the line profile; the best candidates are accretion, winds and stellar activity. We monitored the C IV 1548/1550 Å doublet in the nearby, bright CTTS TW Hya to correlate it with i) the cool wind, as seen in COS NUV Mg II line profiles, ii) the photometric period from joint ground-based monitoring, iii) the accretion rate as determined from the UV continuum and iv) the Ha line profile from independent ground-based observations. The observations span 10 orbits distributed over a few weeks to cover the typical time scales of stellar rotation, accretion and winds. On short time scales (seconds) the variability in the data is compatible with counting statistics when we take certain instrumental effects (the detector dead-time fraction increases when the wavelength calibration lamps are switched on). This rules out any type of coherent accretion shock fluctuation as predicted in some simulations. On longer time scales (days) variability of a factor of 3 in the continuum and similarly massive changes in the line shape are seen. The ratio of the two lines of the doublet indicates that the lines are optically thick, calling into question the idea that the blue-shifted components of the C IV lines are formed in the pre-shock region.

Literary Genres in Poetic Texts from the Dead Sea Scrolls

ERIC Educational Resources Information Center

Pickut, William Douglas

2017-01-01

Among the texts of the Dead Sea Scrolls, there are four literary compositions that bear the superscriptional designations shir and mizmor. These designations correspond directly to superscriptional designations provided many times in both the now-canonical Psalter and the various witnesses to those texts unearthed at Qumran. On its face, this fact…

A note on the effects of replenishment of depleted cells on HIV infection dynamics: A graph-theoretic approach

NASA Astrophysics Data System (ADS)

Mukwembi, Simon

2008-02-01

We study the effects of the rate of replacement of dead cells by either healthy cells or by infected cells on HIV infection dynamics through a graph-theoretic approach. Our framework takes into account a reasonable amount of the immune action to any pathogen and the local cell interactions that occur in the lymph nodes. Our results, in an extremal case where dead cells are highly likely to be replaced by healthy cells, show that all cells become healthy in a finite number of steps of given order and infection stops propagating. Further, for this extremal case, we give an algebraic formula for the number of infected cells at any given time in the HIV progression. We also find a sufficient condition, determined by dead cell replacement rate, which guarantees that an infected patient is continually positive, and give bounds on the number of infected, healthy and dead cells at any given time. We apply our theoretical results to a recently proposed model of the HIV infection dynamics.

ON HYDRODYNAMIC MOTIONS IN DEAD ZONES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oishi, Jeffrey S.; Mac Low, Mordecai-Mark, E-mail: jsoishi@astro.berkeley.ed, E-mail: mordecai@amnh.or

We investigate fluid motions near the midplane of vertically stratified accretion disks with highly resistive midplanes. In such disks, the magnetorotational instability drives turbulence in thin layers surrounding a resistive, stable dead zone. The turbulent layers in turn drive motions in the dead zone. We examine the properties of these motions using three-dimensional, stratified, local, shearing-box, non-ideal, magnetohydrodynamical simulations. Although the turbulence in the active zones provides a source of vorticity to the midplane, no evidence for coherent vortices is found in our simulations. It appears that this is because of strong vertical oscillations in the dead zone. By analyzingmore » time series of azimuthally averaged flow quantities, we identify an axisymmetric wave mode particular to models with dead zones. This mode is reduced in amplitude, but not suppressed entirely, by changing the equation of state from isothermal to ideal. These waves are too low frequency to affect sedimentation of dust to the midplane, but may have significance for the gravitational stability of the resulting midplane dust layers.« less

Predominant bacteria isolated from moribund Fusconaia ebena ebonyshells experiencing die-offs in Pickwick Reservoir, Tennessee River, Alabama

USGS Publications Warehouse

Starliper, C.E.; Powell, J.; Garner, J.T.; Schill, W.B.

2011-01-01

Mussel die-offs have been noted in recent years in Pickwick Reservoir, Tennessee River, Alabama. The primary affected species was Fusconaia ebena, but also affected to lesser degrees were Ellipsaria lineolata, Quadrula pustulosa, and Quadrula quadrula. These events were characterized by large numbers of empty shells—fresh-dead and live individuals that were presumed to be diseased because of weak and slow valve closure responses to external stimuli. Anecdotal evidence suggested the possible involvement of an etiological agent, such as a bacterial pathogen. The die-offs have occurred in Pickwick Reservoir (river miles 236–256) in sequential years during the past approximately 10 y. These timeframes have coincided with reduced basin inflows and warmer water temperatures. The majority of the moribund and freshly dead F. ebena were females possibly predisposed to infection and disease from ongoing reproductive activity. Affected and healthy-cohort mussels were collected to characterize the bacterial flora prior to, during, and after a July 2006 die-off, and during a subsequent die-off in September 2008. The numbers of total bacteria from both the 2006 and 2008 die-offs were significantly greater from the diseased specimens. For example, from the September 2008 die-off, the mean count from diseased F. ebena soft tissues was 9.75 × 106 cfu/g, which was more than 100 times greater (P = 0.025) than the mean from healthy cohorts (6.74 × 104 cfu/g). The predominant bacteria from affected F. ebena from July 2006 were Hafnia alvei and Aeromonas sobria, whereas from September 2008 the predominant bacteria were Enterobacter spp., Aeromonas schubertii, Aeromonas veronii bv. veronii, and Aeromonas veronii bv. sobria.

Protective and Anti-Pathology Effects of Sm Fructose-1,6-Bisphosphate Aldolase-Based DNA Vaccine against Schistosoma mansoni by Changing Route of Injection

PubMed Central

Saber, Mohamed; Hammam, Olft; Karim, Amr; Medhat, Amina; Khela, Mamdouh; El-Dabaa, Ehab

2013-01-01

This study aimed to evaluate the efficacy of fructose-1,6-bis phosphate aldolase (SMALDO) DNA vaccination against Schistosoma mansoni infection using different routes of injection. The SMALDO has been cloned into the eukaryotic expression vector pcDNA3.1/V5-His TOPO-TA and was used in injecting Swiss albino mice intramuscularly (IM), subcutaneously (SC), or intraperitoneally (IP) (50 µg/mouse). Mice vaccinated with non-recombinant pcDNA3.1 served as controls. Each group was immunized 4 times at weeks 0, 2, 4, and 6. Two weeks after the last booster dose, all mice groups were infected with 80 S. mansoni cercariae via tail immersion. At week 8 post-infection, animals were sacrificed for assessment of parasitological and histopathological parameters. High anti-SMALDO IgG antibody titers were detected in sera of all vaccinated groups (P<0.01) compared to the control group. Both the IP and SC vaccination routes resulted in a significant reduction in worm burden (46.2% and 28.9%, respectively, P<0.01). This was accompanied by a significant reduction in hepatic and intestinal egg counts (41.7% and 40.2%, respectively, P<0.01) in the IP group only. The number of dead eggs was significantly increased in both IP and IM groups (P<0.01). IP vaccination recorded the highest significant reduction in granuloma number and diameter (54.7% and 29.2%, respectively, P<0.01) and significant increase in dead miracidia (P<0.01). In conclusion, changing the injection route of SMALDO DNA vaccination significantly influenced the efficacy of vaccination. SMALDO DNA vaccination via IP route could be a promising protective and anti-pathology vaccine candidate against S. mansoni infection. PMID:23710082

Application of EMA-qPCR as a complementary tool for the detection and monitoring of Legionella in different water systems.

PubMed

Qin, Tian; Tian, Zhengan; Ren, Hongyu; Hu, Guangchun; Zhou, Haijian; Lu, Jinxing; Luo, Chengwang; Liu, Zunyu; Shao, Zhujun

2012-05-01

Legionella are prevalent in human-made water systems and cause legionellosis in humans. Conventional culturing and polymerase chain reaction (PCR) techniques are not sufficiently accurate for the quantitative analysis of live Legionella bacteria in water samples because of the presence of viable but nonculturable cells and dead cells. Here, we report a rapid detection method for viable Legionella that combines ethidium monoazide (EMA) with quantitative real-time PCR (qPCR) and apply this method to detect Legionella in a large number of water samples from different sources. Results yielded that samples treated with 5 μg/ml EMA for 10 min and subsequently exposed to light irradiation for 5 min were optimal for detecting Legionella. EMA treatment before qPCR could block the signal from approximately 4 log(10) of dead cells. When investigating environmental water samples, the percent-positive rate obtained by EMA-qPCR was significantly higher than conventional PCR and culture methods, and slightly lower than qPCR. The bacterial count of Legionella determined by EMA-qPCR were mostly greater than those determined by culture assays and lower than those determined by qPCR. Acceptable correlations were found between the EMA-qPCR and qPCR results for cooling towers, piped water and hot spring water samples (r = 0.849, P < 0.001) and also found between the EMA-qPCR and culture results for hot spring water samples (r = 0.698, P < 0.001). The results indicate that EMA-qPCR could be used as a complementary tool for the detection and monitoring of Legionella in water systems, especially in hot spring water samples.

Protective and anti-pathology effects of Sm fructose-1,6-bisphosphate aldolase-based DNA vaccine against schistosoma mansoni by changing route of injection.

PubMed

Saber, Mohamed; Diab, Tarek; Hammam, Olft; Karim, Amr; Medhat, Amina; Khela, Mamdouh; El-Dabaa, Ehab

2013-04-01

This study aimed to evaluate the efficacy of fructose-1,6-bis phosphate aldolase (SMALDO) DNA vaccination against Schistosoma mansoni infection using different routes of injection. The SMALDO has been cloned into the eukaryotic expression vector pcDNA3.1/V5-His TOPO-TA and was used in injecting Swiss albino mice intramuscularly (IM), subcutaneously (SC), or intraperitoneally (IP) (50 µg/mouse). Mice vaccinated with non-recombinant pcDNA3.1 served as controls. Each group was immunized 4 times at weeks 0, 2, 4, and 6. Two weeks after the last booster dose, all mice groups were infected with 80 S. mansoni cercariae via tail immersion. At week 8 post-infection, animals were sacrificed for assessment of parasitological and histopathological parameters. High anti-SMALDO IgG antibody titers were detected in sera of all vaccinated groups (P<0.01) compared to the control group. Both the IP and SC vaccination routes resulted in a significant reduction in worm burden (46.2% and 28.9%, respectively, P<0.01). This was accompanied by a significant reduction in hepatic and intestinal egg counts (41.7% and 40.2%, respectively, P<0.01) in the IP group only. The number of dead eggs was significantly increased in both IP and IM groups (P<0.01). IP vaccination recorded the highest significant reduction in granuloma number and diameter (54.7% and 29.2%, respectively, P<0.01) and significant increase in dead miracidia (P<0.01). In conclusion, changing the injection route of SMALDO DNA vaccination significantly influenced the efficacy of vaccination. SMALDO DNA vaccination via IP route could be a promising protective and anti-pathology vaccine candidate against S. mansoni infection.

Effect of amorphous calcium phosphate and silver nanocomposites on dental plaque microcosm biofilms.

PubMed

Cheng, Lei; Weir, Michael D; Xu, Hockin H K; Antonucci, Joseph M; Lin, Nancy J; Lin-Gibson, Sheng; Xu, Sarah M; Zhou, Xuedong

2012-07-01

A dental composite containing amorphous calcium phosphate nanoparticles (NACP) was developed that released calcium (Ca) and phosphate (PO(4)) ions and possessed acid-neutralization capability. There has been little study on incorporation of antibacterial agents into calcium phosphate composites. The objective of this study was to investigate the effect of silver nanoparticle (NAg) mass fraction in NACP nanocomposite on mechanical properties and dental plaque microcosm biofilm for the first time. NACP nanoparticles of 116 nm were synthesized via a spray-drying technique. NAg nanoparticles were synthesized using Ag 2-ethylhexanoate and 2-(tert-butylamino)ethyl methacrylate, yielding NAg of particle size of 2.7 nm that were well-dispersed in the resin. Five NACP nanocomposites were fabricated with NAg mass fractions of 0, 0.028, 0.042, 0.088, and 0.175%, respectively. Mechanical properties of NACP nanocomposites containing 0-0.042% of NAg matched those of a commercial composite without antibacterial activity. Live/dead assay of dental plaque microcosm biofilms showed complete coverage with live bacteria on commercial composite. However, there were increasingly more dead bacteria with higher NAg content in the NACP nanocomposite. Colony-forming unit (CFU) counts for total microorganisms, total streptococci, and mutans streptococci for NACP nanocomposite with 0.042% NAg were about 1/4 those of commercial composite. Lactic acid production on NACP nanocomposite with 0.042% NAg was 1/3 that on commercial composite. In conclusion, novel NACP-NAg nanocomposites were developed which possessed good mechanical properties and potent antibacterial properties, with substantially reduced biofilm viability and lactic acid production. Hence, the NACP-NAg nanocomposites are promising for dental restorations with remineralizing and antibacterial capabilities. Copyright © 2012 Wiley Periodicals, Inc.

Effect of amorphous calcium phosphate and silver nanocomposites on dental plaque microcosm biofilms

PubMed Central

Cheng, Lei; Weir, Michael D.; Xu, Hockin H. K.; Antonucci, Joseph M.; Lin, Nancy J.; Lin-Gibson, Sheng; Xu, Sarah M.; Zhou, Xuedong

2012-01-01

A dental composite containing amorphous calcium phosphate nanoparticles (NACP) was developed that released calcium (Ca) and phosphate (PO4) ions and possessed acid-neutralization capability. There has been little study on incorporation of antibacterial agents into calcium phosphate composites. The objective of this study was to investigate the effect of silver nanoparticle (NAg) mass fraction in NACP nanocomposite on mechanical properties and dental plaque microcosm biofilm for the first time. NACP nanoparticles of 116 nm were synthesized via a spray-drying technique. NAg nanoparticles were synthesized using Ag 2-ethylhexanoate and 2-(tert-butylamino)ethyl methacrylate, yielding NAg of particle size of 2.7 nm that were well-dispersed in the resin. Five NACP nanocomposites were fabricated with NAg mass fractions of 0, 0.028, 0.042, 0.088, and 0.175%, respectively. Mechanical properties of NACP nanocomposites containing 0–0.042% of NAg matched those of a commercial composite without antibacterial activity. Live/dead assay of dental plaque microcosm biofilms showed complete coverage with live bacteria on commercial composite. However, there were increasingly more dead bacteria with higher NAg content in the NACP nanocomposite. Colony-forming unit (CFU) counts for total microorganisms, total Streptococci, and mutans Streptococci for NACP nanocomposite with 0.042% NAg were about 1/4 those of commercial composite. Lactic acid production on NACP nanocomposite with 0.042% NAg was 1/3 that on commercial composite. In conclusion, novel NACP–NAg nanocomposites were developed which possessed good mechanical properties and potent antibacterial properties, with substantially reduced biofilm viability and lactic acid production. Hence, the NACP–NAg nanocomposites are promising for dental restorations with remineralizing and antibacterial capabilities. PMID:22566464

Quantification of viable Legionella pneumophila cells using propidium monoazide combined with quantitative PCR.

PubMed

Yáñez, M Adela; Nocker, Andreas; Soria-Soria, Elena; Múrtula, Raquel; Martínez, Lorena; Catalán, Vicente

2011-05-01

One of the greatest challenges of implementing fast molecular detection methods as part of Legionella surveillance systems is to limit detection to live cells. In this work, a protocol for sample treatment with propidium monoazide (PMA) in combination with quantitative PCR (qPCR) has been optimized and validated for L. pneumophila as an alternative of the currently used time-consuming culture method. Results from PMA-qPCR were compared with culture isolation and traditional qPCR. Under the conditions used, sample treatment with 50 μM PMA followed by 5 min of light exposure were assumed optimal resulting in an average reduction of 4.45 log units of the qPCR signal from heat-killed cells. When applied to environmental samples (including water from cooling water towers, hospitals, spas, hot water systems in hotels, and tap water), different degrees of correlations between the three methods were obtained which might be explained by different matrix properties, but also varying degrees of non-culturable cells. It was furthermore shown that PMA displayed substantially lower cytotoxicity with Legionella than the alternative dye ethidium monoazide (EMA) when exposing live cells to the dye followed by plate counting. This result confirmed the findings with other species that PMA is less membrane-permeant and more selective for the intact cells. In conclusion, PMA-qPCR is a promising technique for limiting detection to intact cells and makes Legionella surveillance data substantially more relevant in comparison with qPCR alone. For future research it would be desirable to increase the method's capacity to exclude signals from dead cells in difficult matrices or samples containing high numbers of dead cells. Copyright © 2011 Elsevier B.V. All rights reserved.

The Dead Donor Rule: Can It Withstand Critical Scrutiny?

PubMed Central

Miller, Franklin G.; Truog, Robert D.; Brock, Dan W.

2010-01-01

Transplantation of vital organs has been premised ethically and legally on “the dead donor rule” (DDR)—the requirement that donors are determined to be dead before these organs are procured. Nevertheless, scholars have argued cogently that donors of vital organs, including those diagnosed as “brain dead” and those declared dead according to cardiopulmonary criteria, are not in fact dead at the time that vital organs are being procured. In this article, we challenge the normative rationale for the DDR by rejecting the underlying premise that it is necessarily wrong for physicians to cause the death of patients and the claim that abandoning this rule would exploit vulnerable patients. We contend that it is ethical to procure vital organs from living patients sustained on life support prior to treatment withdrawal, provided that there is valid consent for both withdrawing treatment and organ donation. However, the conservatism of medical ethics and practical concerns make it doubtful that the DDR will be abandoned in the near future. This leaves the current practice of organ transplantation based on the “moral fiction” that donors are dead when vital organs are procured. PMID:20439355

Persistence of bacterial DNA in orthopedic infections.

PubMed

Kaplan, Heidi B; Miranda, Justin A; Gogola, Gloria R; Gomez, Karen; Ambrose, Catherine G

2018-06-01

Polymerase chain reaction (PCR) has been proposed as a method to identify bacteria in clinical samples because it is more sensitive than culture techniques and can produce results rapidly. However, PCR can detect DNA from dead cells and thus cannot distinguish between live and dead cells in a tissue sample. Killed Staphylococcus aureus cells were implanted into the femurs and knee joints of rats to determine the length of time that DNA from dead cells is detectable in a living animal under conditions similar to common orthopedic infections. In the joint infection model studied here, the DNA from the dead planktonic bacteria was detected using PCR immediately after injection or 24 h later, but was undetectable 48 and 72 h after injection. In the biofilm implanted-device model studied, the DNA from these dead biofilm cells was detected by PCR immediately after implantation and at 24 h, but not at 48 or 72 h. Thus, our results indicate that DNA from dead cells does not persist in these animal model systems for more than 2 days, which should reduce concerns about possible false positive results using molecular DNA-based techniques for the detection of pathogens. Copyright © 2018. Published by Elsevier Inc.

Cicada Wing Surface Topography: An Investigation into the Bactericidal Properties of Nanostructural Features.

PubMed

Kelleher, S M; Habimana, O; Lawler, J; O' Reilly, B; Daniels, S; Casey, E; Cowley, A

2016-06-22

Recently, the surface of the wings of the Psaltoda claripennis cicada species has been shown to possess bactericidal properties and it has been suggested that the nanostructure present on the wings was responsible for the bacterial death. We have studied the surface-based nanostructure and bactericidal activity of the wings of three different cicadas (Megapomponia intermedia, Ayuthia spectabile and Cryptotympana aguila) in order to correlate the relationship between the observed surface topographical features and their bactericidal properties. Atomic force microscopy and scanning electron microscopy performed in this study revealed that the tested wing species contained a highly uniform, nanopillar structure on the surface. The bactericidal properties of the cicada wings were investigated by assessing the viability of autofluorescent Pseudomonas fluorescens cells following static adhesion assays and targeted dead/live fluorescence staining through direct microscopic counting methods. These experiments revealed a 20-25% bacterial surface coverage on all tested wing species; however, significant bactericidal properties were observed in the M. intermedia and C. aguila species as revealed by the high dead:live cell ratio on their surfaces. The combined results suggest a strong correlation between the bactericidal properties of the wings and the scale of the nanotopography present on the different wing surfaces.

Demographic patterns of the shrub Ceanothus megacarpus in an old stand of chaparral in the Santa Monica Mountains

USGS Publications Warehouse

Montygierd-Loyba, T. M.; Keeley, J.E.; DeVries, J.J.

1986-01-01

Wildfires have had a major influence on the structural and functional adaptations that have evolved in Mediterranean-type ecosystems. Some chaparral shrubs sprout after fires while others produce serotinous cones or seeds refractory to germination until they are cued by a fire. Ceanothus megacarpus is a sclerophylous shrub commonly found in California in either pure of mixed stands which does not survive fires but whose seeds germinate following a fire. Because in recent decades man-made fires have become frequent, few older stands remain, and they have been described as "decadent" or "senescent." Since data on older chaparral stands are scarce, a stand of chaparral in the Santa Monica Mountains of southern California, which last burned in 1929 was studied in an effort to elucidate the survivorship patterns and community structure of Ceanothus megacarpus as it ages. Ceanothus is responsible for 68 percent of the basal coverage at this mixed stand, and one-eighth of the Ceanothus were found to be dead. Over 130 such dead individuals were cut at ground level and aged by ring counts to establish the survivorship curve for this species in this chaparral community in the absence of fires.

Cell tracking using iron oxide fails to distinguish dead from living transplanted cells in the infarcted heart.

PubMed

Winter, E M; Hogers, B; van der Graaf, L M; Gittenberger-de Groot, A C; Poelmann, R E; van der Weerd, L

2010-03-01

Recently, debate has arisen about the usefulness of cell tracking using iron oxide-labeled cells. Two important issues in determining the usefulness of cell tracking with MRI are generally overlooked; first, the effect of graft rejection in immunocompetent models, and second, the necessity for careful histological confirmation of the fate of the labeled cells in the presence of iron oxide. Therefore, both iron oxide-labeled living as well as dead epicardium-derived cells (EPDCs) were investigated in ischemic myocardium of immunodeficient non-obese diabetic (NOD)/acid: non-obese diabetic severe combined immunodeficient (NOD/scid) mice with 9.4T MRI until 6 weeks after surgery, at which time immunohistochemical analysis was performed. In both groups, voids on MRI scans were observed that did not change in number, size, or localization over time. Based on MRI, no distinction could be made between living and dead injected cells. Prussian blue staining confirmed that the hypointense spots on MRI corresponded to iron-loaded cells. However, in the dead-EPDC recipients, all iron-positive cells appeared to be macrophages, while the living-EPDC recipients also contained engrafted iron-loaded EPDCs. Iron labeling is inadequate for determining the fate of transplanted cells in the immunodeficient host, since dead cells produce an MRI signal indistinguishable from incorporated living cells. (c) 2010 Wiley-Liss, Inc.

Radiocarbon Records of Fossil Fuel Emissions From Urban Trees in the Greater Salt Lake Valley From Mid-Century to Present.

NASA Astrophysics Data System (ADS)

Chritz, K.; Buchert, M.; Walker, J. C.; Mendoza, D.; Pataki, D. E.; Xu, X.; Lin, J. C.

2017-12-01

Generating long term records of fossil fuel emissions of urban environments is complicated by the fact that direct observations of emissions and urban atmospheric CO2 concentrations were only collected in the recent past. Radiocarbon (14C) in tree rings from urban trees can provide archives of fossil fuel emissions that may track population growth over time, as higher population density is typically correlated with increased vehicular traffic and associated CO2 emissions, which are radiocarbon dead. We present radiocarbon measurements (n=125) from five roadside green ash trees (Fraxinus pennsylvanica) located in three cities of northern Utah - Salt Lake City (urban, 2016 population: 193,744), Logan City (agricultural, 2016 population: 49,110) and Heber (rural, 2016 population: 14,969). Urban trees were cored in four cardinal directions and ring widths were measured and counted to establish a chronology. One ring from every third year in a single core from each tree was removed and holocellulose was extracted from bulk wood of individual rings for 14C analysis. Fraction CO2 from fossil fuel burning (CO2-ff) was calculated using a simple mass-balance calculation from measured 14C values and remote background atmospheric 14CO2 values for NH Zone 2. The data from all three cities indicate a general trend of increasing CO2-ff uptake by the trees from 1980s to present, as expected with increased population growth and vehicular traffic. However, records in all three cities show unique elevated CO2-ff prior to the 1980s, assuming similar climate patterns through time, diverging from historic population size. We employed atmospheric simulations from the STILT (Stochastic Time-Inverted Lagrangian Transport) models for each of these trees to create footprints to determine source areas for CO2. These footprints reveal that atmospheric sampling areas can be large for certain trees, and other sources of 14C dead carbon, such as coal and natural gas from industrial emissions, should also be considered when building these records.

Tectonic evolution of the Qumran Basin from high-resolution 3.5-kHz seismic profiles and its implication for the evolution of the northern Dead Sea Basin

NASA Astrophysics Data System (ADS)

Lubberts, Ronald K.; Ben-Avraham, Zvi

2002-02-01

The Dead Sea Basin is a morphotectonic depression along the Dead Sea Transform. Its structure can be described as a deep rhomb-graben (pull-apart) flanked by two block-faulted marginal zones. We have studied the recent tectonic structure of the northwestern margin of the Dead Sea Basin in the area where the northern strike-slip master fault enters the basin and approaches the western marginal zone (Western Boundary Fault). For this purpose, we have analyzed 3.5-kHz seismic reflection profiles obtained from the northwestern corner of the Dead Sea. The seismic profiles give insight into the recent tectonic deformation of the northwestern margin of the Dead Sea Basin. A series of 11 seismic profiles are presented and described. Although several deformation features can be explained in terms of gravity tectonics, it is suggested that the occurrence of strike-slip in this part of the Dead Sea Basin is most likely. Seismic sections reveal a narrow zone of intensely deformed strata. This zone gradually merges into a zone marked by a newly discovered tectonic depression, the Qumran Basin. It is speculated that both structural zones originate from strike-slip along right-bending faults that splay-off from the Jordan Fault, the strike-slip master fault that delimits the active Dead Sea rhomb-graben on the west. Fault interaction between the strike-slip master fault and the normal faults bounding the transform valley seems the most plausible explanation for the origin of the right-bending splays. We suggest that the observed southward widening of the Dead Sea Basin possibly results from the successive formation of secondary right-bending splays to the north, as the active depocenter of the Dead Sea Basin migrates northward with time.

Single and multiple streamer DBD micro-discharges for testing inactivation of biologically contaminated surfaces

NASA Astrophysics Data System (ADS)

Prukner, Vaclav; Dolezalova, Eva; Simek, Milan

2014-10-01

Highly reactive environment produced by atmospheric-pressure, non-equilibrium plasmas generated by surface dielectric barrier discharges (SDBDs) may be used for inactivation of biologically contaminated surfaces. We investigated decontamination efficiency of reactive environment produced by single/multiple surface streamer micro-discharge driven by amplitude-modulated AC power in coplanar electrode geometry on biologically contaminated surface by Escherichia coli. The discharges were fed by synthetic air with water vapor admixtures at atmospheric pressure, time of treatment was set from 10 second to 10 minutes, diameters of used SDBD electrodes (single and multiple streamer) and homogeneously contaminated disc samples were equal (25 mm), the distance between the electrode and contaminated surface was 2 mm. Both a conventional cultivation and fluorescent method LIVE/DEAD Bacterial Viability kit were applied to estimate counts of bacteria after the plasma treatment. Inactivation was effective and bacteria partly lost ability to grow and became injured and viable/active but non-cultivable (VBNC/ABNC). Work was supported by the MEYS under Project LD13010, VES13 COST CZ (COST Action MP 1101).

Ascaris lumbricoides egg die-off in an experimental excreta storage system and public health implication in Vietnam.

PubMed

Vu-Van, Tu; Pham-Duc, Phuc; Winkler, Mirko S; Zurbrügg, Christian; Zinsstag, Jakob; Le Thi Thanh, Huong; Bich, Tran Huu; Nguyen-Viet, Hung

2017-02-01

We studied the influence of different additive materials (lime, and rice husk) and aeration conditions on Ascaris lumbricoides egg die-off in 24 vaults of an experimental excreta storage unit. Excreta samples were collected once every two weeks over a 181-day period. Temperature, pH, and moisture content were recorded. A. lumbricoides eggs were quantitatively analyzed by the Romanenko method, which identified and counted live and dead eggs. From the first sampling (0 storage day) to the final sampling (181 storage days) the average percentage of viable A. lumbricoides eggs decreased gradually from 76.72 ± 11.23% (mean ± SD) to 8.26 ± 5.20%. The storage time and the high pH value significantly increased the die-off of helminth eggs. Over 181 storage days, all vaults option effectively reduced A. lumbricoides eggs die-off. The best vault option, with aeration and 10% lime per total weight, met the WHO standard for excreta treatment on the 111th storage day.

Interaction between loggerhead sea turtles (Caretta caretta) and marine litter in Sardinia (Western Mediterranean Sea).

PubMed

Camedda, Andrea; Marra, Stefano; Matiddi, Marco; Massaro, Giorgio; Coppa, Stefania; Perilli, Angelo; Ruiu, Angelo; Briguglio, Paolo; de Lucia, G Andrea

2014-09-01

Anthropogenic debris in the environment affects many species that accidentally ingest it. The aim of this study is to evaluate the quantity and composition of marine litter ingested by loggerheads in Sardinia, thus supplying for the lack of data in the existing literature for this area. Seventeen of the 121 (14.04%) monitored turtles presented debris in their digestive tracts. Litter in faecal pellet of alive individuals (n = 91) and in gastro-intestinal contents of dead ones (n = 30) was categorized, counted and weighed. User plastic was the main category of ingested debris with a frequency of occurrence of 13.22% of the total sample, while sheet (12.39%) and fragments (9.09%) were the most relevant sub-categories. This study highlights for the first time the incidence of litter in alive turtles in Sardinia. This contribution improves the knowledge about marine litter interaction on Caretta caretta as bio-indicator. Results will be useful for the Marine Strategy implementation. Copyright © 2013 Elsevier Ltd. All rights reserved.

A study of nonflammable ArCO 2-hydrocarbon gas mixtures for limited streamer tubes

NASA Astrophysics Data System (ADS)

Cartwright, S.; Schneekloth, U.; Alpat, B.; Artemi, C.; Battiston, R.; Bilei, G.; Italiani, M.; Pauluzzi, M.; Servoli, L.; Messner, R.; Wyss, J.; Zdarko, R.; Johnson, J.

1989-04-01

The gas mixtures generally used until now in limited streamer tube detectors (Ar+C 4H 10 or Ar+CO 2+C 5H 12) are very flammable when leaked into air. The safety issues are therefore very relevant for large-volume underground experiments. We have found a set of completely safe (i.e. nonflammable) ternary mixtures of the kind Ar + hydrocarbon + CO 2 containing less than ˜ 5% of Ar and less than ˜ 10% of hydrocarbon. We tested C 4H 10, C 5H 12 and C 6H 14 as quenching agents. The main characteristics of the various mixtures have been measured: singles (untriggered) counting rate versus high voltage and with different dead times, and average charge. The stability of these mixtures is good, and their spurious streamer activity is compared with the standard binary or ternary mixture. We studied in particular the combination Ar(2.5%) + C 4H 10(9.5%) + CO 2(88%). All the data suggest that this or a similar gas mixture can successfully replace standard flammable mixtures both in tracking devices and hadron calorimeters.

On the interaction of vortices and internal waves in the dead-water problem

NASA Astrophysics Data System (ADS)

Hester, Eric

2017-11-01

Dead water refers to a mysterious increase in resistance experienced by boats in density-stratified waters. The problem has been documented since ancient times, and studied scientifically for over a century. These investigations have revealed the role of internal waves in generating drag. However, analytical approaches neglect important vortex dynamics, which experiments fail to visualise. For the first time, we study the phenomenon using state-of-the-art numerical simulations. We reproduce the effect and show it is greatest in strongly nonlinear regimes poorly modelled by current theory. The most exciting development found a new trailing vortex coupled to the boat. This robust structure is consistent with sailors accounts, but has been missed in previous scientific studies. We expect these results to lead to actionable ways to mitigate dead water in the real world.

Foehn-induced effects on local dust pollution, frontal clouds and solar radiation in the Dead Sea valley

NASA Astrophysics Data System (ADS)

Kishcha, Pavel; Starobinets, Boris; Savir, Amit; Alpert, Pinhas; Kaplan, Michael

2018-06-01

Despite the long history of investigation of foehn phenomena, there are few studies of the influence of foehn winds on air pollution and none in the Dead Sea valley. For the first time the foehn phenomenon and its effects on local dust pollution, frontal cloudiness and surface solar radiation were analyzed in the Dead Sea valley, as it occurred on 22 March 2013. This was carried out using both numerical simulations and observations. The foehn winds intensified local dust emissions, while the foehn-induced temperature inversion trapped dust particles beneath this inversion. These two factors caused extreme surface dust concentration in the western Dead Sea valley. The dust pollution was transported by west winds eastward, to the central Dead Sea valley, where the speed of these winds sharply decreased. The transported dust was captured by the ascending airflow contributing to the maximum aerosol optical depth (AOD) over the central Dead Sea valley. On the day under study, the maximum surface dust concentration did not coincide with the maximum AOD: this being one of the specific effects of the foehn phenomenon on dust pollution in the Dead Sea valley. Radar data showed a passage of frontal cloudiness through the area of the Dead Sea valley leading to a sharp drop in noon solar radiation. The descending airflow over the downwind side of the Judean Mountains led to the formation of a cloud-free band followed by only the partial recovery of solar radiation because of the extreme dust pollution caused by foehn winds.

Dead sea asphalts: historical aspects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nissenbaum, A.

1978-05-01

Asphalts are present in the Dead Sea basin in three forms: (1) huge blocks, up to 100 tons in weight, composed of extremely pure (>99.99%) solid asphalt occasionally found floating on the lake, (2) veins, seepages, and cavity and fissure fillings in Lower Cretaceous to Holocene rocks, and (3) ozocerite veins on the eastern shore of the lake. Dead Sea asphalts probably have been documented over a longer period of time than any other hydrocarbon deposit--from antiquity to the 19th century. Major uses of asphalt from the Dead Sea have been as an ingredient in the embalming process, for medicinalmore » purposes, for fumigation, and for agriculture. The first known war for control of a hydrocarbon deposit was in the Dead Sea area in 312 B.C. between the Seleucid Syrians and the Nabatean Arabs who lived around the lake. Surface manifestations of asphalt are linked closely to tectonic activity. In the lake itself, the asphalt is associated with diapirs During certain historic periods, tectonic and diapiric activity caused frequent liberation to the Dead Sea surface of semiliquid asphalt associated with large amounts of hydrogen sulfide gas. When the tectonic activity was attenuated, as in the 19th and 20th centuries, the rate of asphalt seepage to the bottom sediments of the Dead Sea was much slower and the asphalt solidified on the lake bottom. The release of asphalt to the surface became much more sporadic, and may have resulted in part from earthquakes. Thus, future asphalt prospecting in the Dead Sea area should be conducted along the boundaries of diapirs or their associated faults.« less

Relationship between 'live' and dead benthic foraminiferal assemblages in the abyssal NE Atlantic

NASA Astrophysics Data System (ADS)

Stefanoudis, Paris V.; Bett, Brian J.; Gooday, Andrew J.

2017-03-01

Dead foraminiferal assemblages within the sediment mixed layer provide an integrated, time-averaged view of the foraminiferal fauna, while the relationship between dead and live assemblages reflects the population dynamics of different species together with taphonomic processes operating over the last few hundred years. Here, we analysed four samples for 'live' (Rose-Bengal-stained) and dead benthic foraminifera (0-1 cm sediment layer, >150 μm) from four sites in the area of the Porcupine Abyssal Plain Sustained Observatory (PAP-SO; NE Atlantic, 4850 m water depth). Two sites were located on abyssal hills and two on the adjacent abyssal plain. Our results indicate that the transition from live to dead benthic foraminiferal assemblages involved a dramatic loss of delicate agglutinated and organic-walled tests (e.g. Lagenammina, Nodellum, Reophax) with poor preservation potential, and to a lesser extent that of some relatively fragile calcareous tests (mostly miliolids), possibly a result of dissolution. Other processes, such as the transport of tests by bottom currents and predation, are unlikely to have substantially altered the composition of dead faunas. Positive live to dead ratios suggest that some species (notably Epistominella exigua and Bolivina spathulata) may have responded to recent phytodetritus input. Although the composition of live assemblages seemed to be influenced by seafloor topography (abyssal hills vs. plain), no such relation was found for dead assemblages. We suggest that PAP-SO fossil assemblages are likely to be comparable across topographically contrasting sites, and dominated by calcareous and some robust agglutinated forms with calcitic cement (e.g. Eggerella).

Finding the global minimum: a fuzzy end elimination implementation

NASA Technical Reports Server (NTRS)

Keller, D. A.; Shibata, M.; Marcus, E.; Ornstein, R. L.; Rein, R.

1995-01-01

The 'fuzzy end elimination theorem' (FEE) is a mathematically proven theorem that identifies rotameric states in proteins which are incompatible with the global minimum energy conformation. While implementing the FEE we noticed two different aspects that directly affected the final results at convergence. First, the identification of a single dead-ending rotameric state can trigger a 'domino effect' that initiates the identification of additional rotameric states which become dead-ending. A recursive check for dead-ending rotameric states is therefore necessary every time a dead-ending rotameric state is identified. It is shown that, if the recursive check is omitted, it is possible to miss the identification of some dead-ending rotameric states causing a premature termination of the elimination process. Second, we examined the effects of removing dead-ending rotameric states from further considerations at different moments of time. Two different methods of rotameric state removal were examined for an order dependence. In one case, each rotamer found to be incompatible with the global minimum energy conformation was removed immediately following its identification. In the other, dead-ending rotamers were marked for deletion but retained during the search, so that they influenced the evaluation of other rotameric states. When the search was completed, all marked rotamers were removed simultaneously. In addition, to expand further the usefulness of the FEE, a novel method is presented that allows for further reduction in the remaining set of conformations at the FEE convergence. In this method, called a tree-based search, each dead-ending pair of rotamers which does not lead to the direct removal of either rotameric state is used to reduce significantly the number of remaining conformations. In the future this method can also be expanded to triplet and quadruplet sets of rotameric states. We tested our implementation of the FEE by exhaustively searching ten protein segments and found that the FEE identified the global minimum every time. For each segment, the global minimum was exhaustively searched in two different environments: (i) the segments were extracted from the protein and exhaustively searched in the absence of the surrounding residues; (ii) the segments were exhaustively searched in the presence of the remaining residues fixed at crystal structure conformations. We also evaluated the performance of the method for accurately predicting side chain conformations. We examined the influence of factors such as type and accuracy of backbone template used, and the restrictions imposed by the choice of potential function, parameterization and rotamer database. Conclusions are drawn on these results and future prospects are given.

Stratigraphy, climate and downhole logging data - an example from the ICDP Dead Sea deep drilling project

NASA Astrophysics Data System (ADS)

Coianiz, Lisa; Ben-Avraham, Zvi; Lazar, Michael

2017-04-01

During the late Quaternary a series of lakes occupied the Dead Sea tectonic basin. The sediments that accumulated within these lakes preserved the environmental history (tectonic and climatic) of the basin and its vicinity. Most of the information on these lakes was deduced from exposures along the marginal terraces of the modern Dead Sea, e.g. the exposures of the last glacial Lake Lisan and Holocene Dead Sea. The International Continental Drilling Program (ICDP) project conducted in the Dead Sea during 2010-2011 recovered several cores that were drilled in the deep depocenter of the lake (water depth of 300 m) and at the margin (depth of 3 m offshore Ein Gedi spa). New high resolution logging data combined with a detailed lithological description and published age models for the deep 5017-1-A borehole were used to establish a sequence stratigraphic framework for the Lakes Amora, Samra, Lisan and Zeelim strata. This study presents a stratigraphic timescale for reconstructing the last ca 225 ka. It provides a context within which the timing of key sequence surfaces identified in the distal part of the basin can be mapped on a regional and stratigraphic time frame. In addition, it permitted the examination of depositional system tracts and related driving mechanisms controlling their formation. The sequence stratigraphic model developed for the Northern Dead Sea Basin is based on the identification of sequence bounding surfaces including: sequence boundary (SB), transgressive surface (TS) and maximum flooding surface (MFS). They enabled the division of depositional sequences into a Lowstand systems tracts (LST), Transgressive systems tracts (TST) and Highstand systems tracts (HST), which can be interpreted in terms of relative lake level changes. The analysis presented here show that system tract stacking patterns defined for the distal 5017-1-A borehole can be correlated to the proximal part of the basin, and widely support the claim that changes in relative lake levels were synchronous across the northern Dead Sea, although differences do exist. These discrepancies can possibly be explained in part by the tectonic nature of the basin. Within the 5017-1-A section, the interpreted changes in depositional environments derived primarily from the gamma ray log patterns show a good correlation in time with sequence-chronostratigraphic framework, extracted lake level curves and paleohydrological records of other areas worldwide. Sequence stratigraphic analysis presented here allows for a detailed, high resolution examination of the sedimentary sequences in the Northern Dead Sea Basin together with an independent proxy that is an indirect indicator of changes in relative lake level.

SU-D-BRA-04: Fractal Dimension Analysis of Edge-Detected Rectal Cancer CTs for Outcome Prediction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong, H; Wang, J; Hu, W

2015-06-15

Purpose: To extract the fractal dimension features from edge-detected rectal cancer CTs, and to examine the predictability of fractal dimensions to outcomes of primary rectal cancer patients. Methods: Ninety-seven rectal cancer patients treated with neo-adjuvant chemoradiation were enrolled in this study. CT images were obtained before chemoradiotherapy. The primary lesions of the rectal cancer were delineated by experienced radiation oncologists. These images were extracted and filtered by six different Laplacian of Gaussian (LoG) filters with different filter values (0.5–3.0: from fine to coarse) to achieve primary lesions in different anatomical scales. Edges of the original images were found at zero-crossingsmore » of the filtered images. Three different fractal dimensions (box-counting dimension, Minkowski dimension, mass dimension) were calculated upon the image slice with the largest cross-section of the primary lesion. The significance of these fractal dimensions in survival, recurrence and metastasis were examined by Student’s t-test. Results: For a follow-up time of two years, 18 of 97 patients had experienced recurrence, 24 had metastasis, and 18 were dead. Minkowski dimensions under large filter values (2.0, 2.5, 3.0) were significantly larger (p=0.014, 0.006, 0.015) in patients with recurrence than those without. For metastasis, only box-counting dimensions under a single filter value (2.5) showed differences (p=0.016) between patients with and without. For overall survival, box-counting dimensions (filter values = 0.5, 1.0, 1.5), Minkowski dimensions (filter values = 0.5, 1.5, 2.0, 2,5) and mass dimensions (filter values = 1.5, 2.0) were all significant (p<0.05). Conclusion: It is feasible to extract shape information by edge detection and fractal dimensions analysis in neo-adjuvant rectal cancer patients. This information can be used to prognosis prediction.« less

Growth responses of mature loblolly pine to dead wood.manipulations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulyshen, Michael D.; Horn, Scott; Hanula, James L.

Large-scale manipulations of dead wood in mature Pinus taeda L. stands in the southeastern United States included a major one-time input of logs (fivefold increase in log volume) created by felling trees onsite, annual removals of all dead wood above >10 cm in diameter and >60 cm in length, and a reference in which no manipulations took place. We returned over a decade later to determine how these treatments affected tree growth using increment cores. There were no significant differences in tree density, basal area or tree diameters among treatments at the time of sampling. Although tree growth was consistentlymore » higher in the log-input plots and lower in the removal plots, this was true even during the 5 year period before the experiment began. When growth data from this initial period were included in the model as a covariate, no differences in post-treatment tree growth were detected. It is possible that treatment effects will become apparent after more time has passed, however.« less

Analysis of single ion channel data incorporating time-interval omission and sampling

PubMed Central

The, Yu-Kai; Timmer, Jens

2005-01-01

Hidden Markov models are widely used to describe single channel currents from patch-clamp experiments. The inevitable anti-aliasing filter limits the time resolution of the measurements and therefore the standard hidden Markov model is not adequate anymore. The notion of time-interval omission has been introduced where brief events are not detected. The developed, exact solutions to this problem do not take into account that the measured intervals are limited by the sampling time. In this case the dead-time that specifies the minimal detectable interval length is not defined unambiguously. We show that a wrong choice of the dead-time leads to considerably biased estimates and present the appropriate equations to describe sampled data. PMID:16849220

Anthropogenic-enhanced erosion following the Neolithic Revolution in the Southern Levant: Records from the Dead Sea deep drilling core

NASA Astrophysics Data System (ADS)

Lu, Yin; Waldmann, Nicolas; Nadel, Dani; Marco, Shmuel

2017-04-01

In addition to tectonics and climatic changes, humans have exerted a significant impact on surface erosion over timescales ranging from years to centuries. However, such kind of impact over millennial timescales remains unsubstantiated. The Dead Sea drainage basin offers a rare combination of well-documented substantial climate change, intense tectonics and abundant archaeological evidence for past human activity in the Southern Levant. It serves as a natural laboratory for understanding how sedimentation rates in a deep basin are related to climate change, tectonics, and anthropogenic impacts on the landscape. Here we show how basin-wide erosion rates are recorded by thicknesses of rhythmic detritus laminae and clastic sediment accumulation rates in a long core retrieved by the Dead Sea Deep Drilling Project in the Dead Sea depocenter. During the last 11.5 kyr the average detrital accumulation rate is 3-4 times that during the last two glacial cycles (MIS 7c-2), and the average thickness of detritus laminae in the last 11.6 kyr is 4.5 times that between 21.7 and 11.6 ka, implying an increased erosion rate on the surrounding slopes during the Holocene. We estimate that this intensified erosion is incompatible with tectonic and climatic regimes during the corresponding time interval and further propose a close association with the Neolithic Revolution in the Levant (beginning at 11.5 ka). We thus suggest that human impact on the landscape was the primary driver causing the intensified erosion and that the Dead Sea sedimentary record serves as a reliable recorder of this impact since the Neolithic Revolution.

A high-resolution and intelligent dead pixel detection scheme for an electrowetting display screen

NASA Astrophysics Data System (ADS)

Luo, ZhiJie; Luo, JianKun; Zhao, WenWen; Cao, Yang; Lin, WeiJie; Zhou, GuoFu

2018-02-01

Electrowetting display technology is realized by tuning the surface energy of a hydrophobic surface by applying a voltage based on electrowetting mechanism. With the rapid development of the electrowetting industry, how to analyze efficiently the quality of an electrowetting display screen has a very important significance. There are two kinds of dead pixels on the electrowetting display screen. One is that the oil of pixel cannot completely cover the display area. The other is that indium tin oxide semiconductor wire connecting pixel and foil was burned. In this paper, we propose a high-resolution and intelligent dead pixel detection scheme for an electrowetting display screen. First, we built an aperture ratio-capacitance model based on the electrical characteristics of electrowetting display. A field-programmable gate array is used as the integrated logic hub of the system for a highly reliable and efficient control of the circuit. Dead pixels can be detected and displayed on a PC-based 2D graphical interface in real time. The proposed dead pixel detection scheme reported in this work has promise in automating electrowetting display experiments.

Down dead wood statistics for Maine timberlands, 1995

Treesearch

Linda S. Heath; David C. Chojnacky; David C. Chojnacky

2001-01-01

Down dead wood (DDW) is important for its role in carbon and nutrient cycling, carbon sequestration, wildfire behavior, plant reproduction, and wildlife habitat. DDW was measured for the first time during a forest inventory of Maine by the USDA Forest Service in 1994-1996. Pieces greater than 3 feet long and greater than 3 inches in diameter at point of intersection...

The Roles of Beaconing and Dead Reckoning in Human Virtual Navigation

ERIC Educational Resources Information Center

Bodily, Kent D.; Daniel, Thomas A.; Sturz, Bradley R.

2012-01-01

Beaconing is a process in which the distance between a visual landmark and current position is reduced in order to return to a location. In contrast, dead reckoning is a process in which vestibular, kinesthetic and/or optic flow cues are utilized to update speed of movement, elapsed time of movement, and direction of movement to return to a…

Dia de los Muertos: An Illustrated Essay and Bibliography.

ERIC Educational Resources Information Center

California Univ., Santa Barbara. University Library.

Among Mexico's most original traditions is the holiday dedicated to honoring the dead, Dia de los Muertos, November 2. This tradition combines aspects that define the national spirit. At the same time that it is a solemn festivity to remember the dead, it becomes a fiesta in its own right. Death, more than a thing to be feared, becomes the motif…

Increased sedimentation following the Neolithic Revolution in the Southern Levant

NASA Astrophysics Data System (ADS)

Lu, Yin; Waldmann, Nicolas; Nadel, Dani; Marco, Shmuel

2017-05-01

The Dead Sea drainage basin offers a rare combination of well-documented substantial climate change, intense tectonics and abundant archaeological evidence for past human activity in the Southern Levant. It serves as a natural laboratory for understanding how sedimentation rates in a deep basin are related to climate change, tectonics, and anthropogenic impacts on the landscape. Here we show how basin-wide erosion rates are recorded by thicknesses of rhythmic detritus laminae and clastic sediment accumulation rates in a long core retrieved by the Dead Sea Deep Drilling Project in the Dead Sea depocenter. During the last 11.5 kyr the average detrital accumulation rate is 3-4 times that during the last two glacial cycles (MIS 7c-2), and the average thickness of detritus laminae in the last 11.6 kyr is 4.5 times that between 21.7 and 11.6 ka, implying an increased erosion rate on the surrounding slopes during the Holocene. We estimate that this intensified erosion is incompatible with tectonic and climatic regimes during the corresponding time interval and further propose a close association with the Neolithic Revolution in the Levant (beginning at 11.5 ka). We thus suggest that human impact on the landscape was the primary driver causing the intensified erosion and that the Dead Sea sedimentary record serves as a reliable recorder of this impact since the Neolithic Revolution.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jull, A.J.T.

Since 1981 we have operated an NSF Accelerator Mass Spectrometry (AMS) Facility at the University of Arizona. The AMS method allows us to use very small samples of carbon, <1 mg for radiocarbon dating in contrast to earlier counting techniques. This has opened a vast array of applications of radiocarbon dating that was difficult to do before AMS because of sample size limitations of decay counting. Some of the many applications of AMS include paleoclimatic studies, archaeological research and the age of first settlement of North America by man, dating of art works and artifacts, fall times and terrestrial residencemore » ages of meteorites, production of {sup 14}C in lunar samples by galactic and solar cosmic rays, studies of in situ {sup 14}C produced by cosmic ray spallation in rocks and ice, and studies of {sup 14}C in groundwater dissolved inorganic carbon and dissolved organic carbon. At our laboratory, we have also successfully applied AMS {sup 14}C to dating of many types of textiles, including silks and linens, art works, documents and artifacts fabricated from wood, parchment, ivory, and bone. The results for many of these samples are often important in questions of the authenticity of these works of art and artifacts. Our studies have encompassed a wide range of art works ranging from the Dead Sea Scrolls, the Shroud of Turin, and the Chinese silk trade to the works of Raphael, Rembrandt, and Picasso. Recently, we also dated the Vinland Map, a controversial document that shows the eastern coast of North America apparently using information from Viking voyages.« less

Characterization of gallium arsenide X-ray mesa p-i-n photodiodes at room temperature

NASA Astrophysics Data System (ADS)

Lioliou, G.; Meng, X.; Ng, J. S.; Barnett, A. M.

2016-03-01

Two GaAs mesa p+-i-n+ photodiodes intended for photon counting X-ray spectroscopy, having an i layer thickness of 7 μm and diameter of 200 μm, have been characterized electrically, for their responsivity at the wavelength range 580 nm to 980 nm and one of them for its performance at detection of soft X-rays, at room temperature. Dark current and capacitance measurements as a function of applied forward and reverse bias are presented. The results show low leakage current densities, in the range of nA/cm2 at the maximum internal electric field (22 kV/cm). The unintentional doping concentration of the i layer, calculated from capacitance measurements, was found to be <1014 cm-3. Photocurrent measurements were performed under visible and near infrared light illumination for both diodes. The analysis of these measurements suggests the presence of a non-active (dead) layer (0.16 μm thickness) at the p+ side top contact interface, where the photogenerated carriers do not contribute to the photocurrent, possibly due to recombination. One of the diodes, D1, was also characterized as detector for room temperature photon counting X-ray spectroscopy; the best energy resolution achieved (FWHM) at 5.9 keV was 745 eV. The noise analysis of the system, based on spectra obtained at different shaping times and applied reverse biases, showed that the dominant source of noise is the dielectric noise. It was also calculated that there was at least (165±24) eV charge trapping noise at 0 V.

NuSTAR Observations of X-Ray Bursts from the Magnetar 1E 1048.1-5937

NASA Technical Reports Server (NTRS)

An, Hongjun; Kaspi, Victoria M.; Beloborodov, Andrei M.; Kouveliotou, Chryssa; Archibald, Robert T.; Boggs, Steven E.; Christensen, Finn E.; Craig, William W.; Gotthelf, Eric V.; Stern, Daniel;

[Cloning and law in Hungary].

PubMed

Julesz, Máté

2015-03-01

Reproductive human cloning is prohibited in Hungary, as in many other countries. Therapeutic human cloning is not prohibited, just like in many other countries. Stem cell therapy is also allowed. Article III, paragraph (3) of the Hungarian basic law (constitution) strictly forbids total human cloning. Article 1 of the Additional Protocol to the Oviedo Convention, on the Prohibition of Cloning Human Beings (1998) stipulates that any intervention seeking to create a human being genetically identical to another human being, whether living or dead, is prohibited. In Hungary, according to Article 174 of the Criminal Code, total human cloning constitutes a crime. Article 180, paragraph (3) of the Hungarian Act on Health declares that embryos shall not be brought about for research purposes; research shall be conducted only on embryos brought about for reproductive purposes when this is authorized by the persons entitled to decide upon its disposal, or when the embryo is damaged. Article 180, paragraph (5) of the Hungarian Act on Health stipulates that multiple individuals who genetically conform to one another shall not be brought about. According to Article 181, paragraph (1) of the Hungarian Act on Health, an embryo used for research shall be kept alive for not longer than 14 days, not counting the time it was frozen for storage and the time period of research.

A new structure design and the basic radiation characteristics test of the intense current tube

NASA Astrophysics Data System (ADS)

Li, Zhiyuan; Ai, Xianyun; Fu, Li; Cui, Hui

2018-02-01

As a kind of special G-M counter, the intense current tube (ICT) is characterized by small ratio of cathode to anode radius, high working current or count rate, and can be used as the detection units of ultra-high range radiation instruments. In this paper, a new design of ICT structure is introduced, not only does it have a minimum ratio of cathode to anode but it also has a cathode which directly sticks out from the sensitive gas. Using COMSOL Multiphysics, we simulated the electric field between the anode and cathode and finalized the optimal structure. The results of processes and experiments show that the structure has better properties, with plateau slope reaching up to 7.4% within 100V, and it also has a wider range of dose rate. The linear data between the bottom limit of 0.2mGy/h and the upper limit of 1Gy/h is quite accurate but it becomes less reliable beyond 1Gy/h. By using Paralyzable model, we deduce that the dead time of the said ICT is less than 13.4 µs, and we will further optimize the readout circuit in order to reduce the resolution time of the circuit in the near future.

Intraperitoneal insemination and retrograde sperm transport in dairy cows.

PubMed

López-Gatius, F; Yániz, J

2000-03-01

To examine the efficiency of retrograde sperm transport following intraperitoneal insemination, live and dead spermatozoa were used at different concentrations, and sperm recovery from cervical mucus (0.5 ml) 2, 6, 12 and 24 h following insemination was evaluated. Forty lactating Friesian cows, in their second to fourth lactation period, were used in this experiment. Thirty-six cows received intraperitoneally either live or dead spermatozoa. Each group of six cows received one of three total sperm numbers of 30, 45 and 90 million. Four cows were inseminated with 90 million spermatozoa into the uterus and served as a control group. All cows were inseminated towards the end of oestrus. After intrauterine insemination sperm recovery declined, but motile and/or immotile spermatozoa were recovered from all cows at any time. In cows inseminated intraperitoneally, sperm was recovered from the cervix at 6-24 h when 90 million were inseminated. A greater number of spermatozoa was recovered after dead rather than after live sperm inseminations. Only immotile, intact or broken spermatozoa and tail-less heads were recovered after intraperitioneal insemination using either live or dead spermatozoa. No sperm was recovered for 30 and 45 million inseminations. Our results show that, following intraperitoneal insemination, there is passive sperm transport from the peritoneal cavity to the genital tract close to the time of ovulation, and suggest a higher sperm retention in the genital tract when live as opposed to dead spermatozoa are used.

Smith predictor with sliding mode control for processes with large dead times

NASA Astrophysics Data System (ADS)

Mehta, Utkal; Kaya, İbrahim

2017-11-01

The paper discusses the Smith Predictor scheme with Sliding Mode Controller (SP-SMC) for processes with large dead times. This technique gives improved load-disturbance rejection with optimum input control signal variations. A power rate reaching law is incorporated in the sporadic part of sliding mode control such that the overall performance recovers meaningfully. The proposed scheme obtains parameter values by satisfying a new performance index which is based on biobjective constraint. In simulation study, the efficiency of the method is evaluated for robustness and transient performance over reported techniques.

Improved marine reservoir age estimation and palaeoclimate synchronisation of the early Holocene Levantine/NW-Arabian region based on identification of the S1 tephra in Dead Sea and Tayma palaeolake sediments

NASA Astrophysics Data System (ADS)

Neugebauer, Ina; Wulf, Sabine; Schwab, Markus J.; Serb, Johanna; Plessen, Birgit; Appelt, Oona; Brauer, Achim

2017-04-01

Due to a lack of tephras identified in marine and terrestrial palaeoclimate records from the Levantine-Arabian area, this region is still not sufficiently connected to the eastern Mediterranean tephrostratigraphical lattice. Here we report on the first finding of cryptotephra in the Holocene lacustrine sediment records of the Dead Sea and the Tayma palaeolake (NW Arabian Peninsula). The major elemental chemistry of the rhyolitic glass shards proves this tephra identical to the distal 'S1 tephra' identified in the Yammoûneh palaeolake, Lebanon (Develle et al, 2009), in a marine sediment record from the SE Levantine basin (Hamann et al., 2010) and in the Sodmein Cave archaeological site in Egypt (Barton et al., 2015). The 'S1 tephra', most likely corresponding to the early Holocene 'Dikkartın' dome eruption of the Erciyes Daǧ volcano in central Anatolia, Turkey, has been dated in the marine record at 8830 ± 140 cal yr BP. We present new age estimates of the 'S1 tephra' based on radiocarbon dating of terrestrial plant remains (Migowski et al., 2004) and pollen concentrates (Dinies et al., 2015), which reveal modelled ages of 8939 ± 83 cal yr BP in the Dead Sea sediments and 9041 ± 254 cal yr BP in Tayma. This allows the estimation of an early Holocene marine reservoir age of ca. 320 years in the SE Levantine Sea. The timing of the volcanic eruption during the early Holocene humid period, which led to the formation of sapropel S1 in the Mediterranean Sea, and the identification of the 'S1 tephra' more than 1200 km to the south are crucial for the synchronisation of marine and terrestrial palaeoclimate records in the eastern Mediterranean region. References: Barton et al., 2015. The role of cryptotephra in refining the chronology of Late Pleistocene human evolution and cultural change in North Africa. Quaternary Sci. Rev. 118, 151-169. Develle et al., 2009. Early Holocene volcanic ash fallout in the Yammoûneh lacustrine basin (Lebanon): Tephrochronological implications for the Near East. Journal of Volcanology and Geothermal Research 186, 416-425. Dinies et al., 2015. When the desert was green: Grassland expansion during the early Holocene in northwestern Arabia. Quatern. Int. 382, 293-302. Hamann et al., 2010. First evidence of a distal early Holocene ash layer in Eastern Mediterranean deep-sea sediments derived from the Anatolian volcanic province. Quaternary Res. 73, 497-506. Migowski et al., 2004. Recurrence pattern of Holocene earthquakes along the Dead Sea transform revealed by varve-counting and radiocarbon dating of lacustrine sediments. Earth Planet. Sc. Lett. 222, 301-314.

Improved confidence intervals when the sample is counted an integer times longer than the blank.

PubMed

Potter, William Edward; Strzelczyk, Jadwiga Jodi

2011-05-01

Past computer solutions for confidence intervals in paired counting are extended to the case where the ratio of the sample count time to the blank count time is taken to be an integer, IRR. Previously, confidence intervals have been named Neyman-Pearson confidence intervals; more correctly they should have been named Neyman confidence intervals or simply confidence intervals. The technique utilized mimics a technique used by Pearson and Hartley to tabulate confidence intervals for the expected value of the discrete Poisson and Binomial distributions. The blank count and the contribution of the sample to the gross count are assumed to be Poisson distributed. The expected value of the blank count, in the sample count time, is assumed known. The net count, OC, is taken to be the gross count minus the product of IRR with the blank count. The probability density function (PDF) for the net count can be determined in a straightforward manner.

Multi-parameter flow cytometry as a process analytical technology (PAT) approach for the assessment of bacterial ghost production.

PubMed

Langemann, Timo; Mayr, Ulrike Beate; Meitz, Andrea; Lubitz, Werner; Herwig, Christoph

2016-01-01

Flow cytometry (FCM) is a tool for the analysis of single-cell properties in a cell suspension. In this contribution, we present an improved FCM method for the assessment of E-lysis in Enterobacteriaceae. The result of the E-lysis process is empty bacterial envelopes-called bacterial ghosts (BGs)-that constitute potential products in the pharmaceutical field. BGs have reduced light scattering properties when compared with intact cells. In combination with viability information obtained from staining samples with the membrane potential-sensitive fluorescent dye bis-(1,3-dibutylarbituric acid) trimethine oxonol (DiBAC4(3)), the presented method allows to differentiate between populations of viable cells, dead cells, and BGs. Using a second fluorescent dye RH414 as a membrane marker, non-cellular background was excluded from the data which greatly improved the quality of the results. Using true volumetric absolute counting, the FCM data correlated well with cell count data obtained from colony-forming units (CFU) for viable populations. Applicability of the method to several Enterobacteriaceae (different Escherichia coli strains, Salmonella typhimurium, Shigella flexneri 2a) could be shown. The method was validated as a resilient process analytical technology (PAT) tool for the assessment of E-lysis and for particle counting during 20-l batch processes for the production of Escherichia coli Nissle 1917 BGs.

Differential enumeration of subpopulations in concentrated frozen and lyophilized cultures of Lactobacillus delbrueckii ssp. bulgaricus.

PubMed

Shao, Yuyu; Wang, Zhaoxia; Bao, Qiuhua; Zhang, Heping

2017-11-01

Differential enumeration of subpopulations in concentrated frozen and lyophilized cultures of Lactobacillus delbrueckii ssp. bulgaricus ND02 derived from 2 propagation procedures was determined. The subpopulations consisted of 3 categories (physiological states): viable cells capable of forming colonies on agar plates (VC+), viable cells incapable of forming colonies on agar plates (VC-), widely referred to as viable but nonculturable (VBNC) cells, and nonviable or dead cells (NVC). Counts of VC+ were recorded using a conventional plate count procedure. A fluorescent vital staining procedure that discriminates between viable (VC+ and VC-) and NVC cells was used to determine the number of viable and nonviable cells. Both propagation procedures had 2 variables: in procedure (P)1, the propagation medium was rich in yeast extract (4.0%) and the pH was maintained at 5.7; in P2, the medium was devoid of yeast extract and the pH was maintained at 5.1. The results showed that post-propagation operations-concentration of cells by centrifugation and subsequent freezing or lyophilization of cell concentrate-induced different degrees of transience from VC+ to VC- states in cells derived from P1 and P2. Compared with cells derived from P2, cells from P1 were more labile to stress associated with centrifugation, freezing, and lyophilization, as revealed by differential counting. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Behaviour of nitinol in osteoblast-like ROS-17 cell cultures.

PubMed

Kapanen, A; Ilvesaro, J; Danilov, A; Ryhänen, J; Lehenkari, P; Tuukkanen, J

2002-02-01

Nickel titanium shape memory metal alloy Nitinol (NiTi) has been used in dental wares and in gastrointestinal surgery. Nitinol is a promising implant material in orthopedics, but its biocompatibility, especially in long-term implantation is not confirmed yet. We studied Nitinol's effect on a cell culture model. Comparisons to stainless steel, pure titanium and pure nickel were performed. The effects of Nitinol on cell death rate, the apoptosis rate and the formation of local contacts were studied on rat osteosarcoma cell line ROS-17 in 48-h cultures. The cell death rate was assessed with combined calcein-ethidium-homodimer labelling. The amount of dead cells 1000 cells were as follows: four in the NiTi, 21 in the Stst, 4.8 in the Ti and 51 in the Ni group. In the NiTi and Ti groups, the number of dead cells was significantly lower (p < or = 0.01) than in Ni group. The rate of apoptosis was detected with TUNEL-assay. The assay results were: 1.93 apoptotic cells 1000 cells in the NiTi, 1.1 in the Stst, 2.98 in the Ti and 0.62 in the Ni group. A comparison of these two results shows that 48% of the dead cells were apoptotic in the NiTi, 56.6 in the Stst, 62% in the Ti and only 1.8% in the Ni group. The focal contacts were stained with a paxillin antibody and counted. There were marked differences in the number of focal contacts per unit area compared to NiTi (774 focal contacts): 335 in Stst (p < or = 0.01), 462 in Ti (p < or = 0.01) and 261 in Ni (p < or = 0.005). Our results show that NiTi is well tolerated by the osteoblastic type ROS-17 cells.

Landsat time series and lidar as predictors of live and dead basal area across five bark beetle-affected forests

Treesearch

Benjamin C. Bright; Andrew T. Hudak; Robert E. Kennedy; Arjan J. H. Meddens

2014-01-01

Bark beetle-caused tree mortality affects important forest ecosystem processes. Remote sensing methodologies that quantify live and dead basal area (BA) in bark beetle-affected forests can provide valuable information to forest managers and researchers. We compared the utility of light detection and ranging (lidar) and the Landsat-based detection of trends in...

A path reconstruction method integrating dead-reckoning and position fixes applied to humpback whales.

PubMed

Wensveen, Paul J; Thomas, Len; Miller, Patrick J O

2015-01-01

Detailed information about animal location and movement is often crucial in studies of natural behaviour and how animals respond to anthropogenic activities. Dead-reckoning can be used to infer such detailed information, but without additional positional data this method results in uncertainty that grows with time. Combining dead-reckoning with new Fastloc-GPS technology should provide good opportunities for reconstructing georeferenced fine-scale tracks, and should be particularly useful for marine animals that spend most of their time under water. We developed a computationally efficient, Bayesian state-space modelling technique to estimate humpback whale locations through time, integrating dead-reckoning using on-animal sensors with measurements of whale locations using on-animal Fastloc-GPS and visual observations. Positional observation models were based upon error measurements made during calibrations. High-resolution 3-dimensional movement tracks were produced for 13 whales using a simple process model in which errors caused by water current movements, non-location sensor errors, and other dead-reckoning errors were accumulated into a combined error term. Positional uncertainty quantified by the track reconstruction model was much greater for tracks with visual positions and few or no GPS positions, indicating a strong benefit to using Fastloc-GPS for track reconstruction. Compared to tracks derived only from position fixes, the inclusion of dead-reckoning data greatly improved the level of detail in the reconstructed tracks of humpback whales. Using cross-validation, a clear improvement in the predictability of out-of-set Fastloc-GPS data was observed compared to more conventional track reconstruction methods. Fastloc-GPS observation errors during calibrations were found to vary by number of GPS satellites received and by orthogonal dimension analysed; visual observation errors varied most by distance to the whale. By systematically accounting for the observation errors in the position fixes, our model provides a quantitative estimate of location uncertainty that can be appropriately incorporated into analyses of animal movement. This generic method has potential application for a wide range of marine animal species and data recording systems.

Can dead zones create structures like a transition disk?

NASA Astrophysics Data System (ADS)

Pinilla, Paola; Flock, Mario; Ovelar, Maria de Juan; Birnstiel, Til

2016-12-01

Context. Regions of low ionisation where the activity of the magneto-rotational instability is suppressed, the so-called dead zones, have been suggested to explain gaps and asymmetries of transition disks. Dead zones are therefore a potential cause for the observational signatures of transition disks without requiring the presence of embedded planets. Aims: We investigate the gas and dust evolution simultaneously assuming simplified prescriptions for a dead zone and a magnetohydrodynamic (MHD) wind acting on the disk. We explore whether the resulting gas and dust distribution can create signatures similar to those observed in transition disks. Methods: We imposed a dead zone and/or an MHD wind in the radial evolution of gas and dust in protoplanetary disks. For the dust evolution, we included the transport, growth, and fragmentation of dust particles. To compare with observations, we produced synthetic images in scattered optical light and in thermal emission at mm wavelengths. Results: In all models with a dead zone, a bump in the gas surface density is produced that is able to efficiently trap large particles (≳ 1 mm) at the outer edge of the dead zone. The gas bump reaches an amplitude of a factor of 5, which can be enhanced by the presence of an MHD wind that removes mass from the inner disk. While our 1D simulations suggest that such a structure can be present only for 1 Myr, the structure may be maintained for a longer time when more realistic 2D/3D simulations are performed. In the synthetic images, gap-like low-emission regions are seen at scattered light and in thermal emission at mm wavelengths, as previously predicted in the case of planet-disk interaction. Conclusions: Main signatures of transition disks can be reproduced by assuming a dead zone in the disk, such as gap-like structure in scattered light and millimetre continuum emission, and a lower gas surface density within the dead zone. Previous studies showed that the Rossby wave instability can also develop at the edge of such dead zones, forming vortices and also creating asymmetries.

Purifying, Separating, and Concentrating Cells From a Sample Low in Biomass

NASA Technical Reports Server (NTRS)

Benardini, James N.; LaDuc, Myron T.; Diamond, Rochelle

2012-01-01

Frequently there is an inability to process and analyze samples of low biomass due to limiting amounts of relevant biomaterial in the sample. Furthermore, molecular biological protocols geared towards increasing the density of recovered cells and biomolecules of interest, by their very nature, also concentrate unwanted inhibitory humic acids and other particulates that have an adversarial effect on downstream analysis. A novel and robust fluorescence-activated cell-sorting (FACS)-based technology has been developed for purifying (removing cells from sampling matrices), separating (based on size, density, morphology), and concentrating cells (spores, prokaryotic, eukaryotic) from a sample low in biomass. The technology capitalizes on fluorescent cell-sorting technologies to purify and concentrate bacterial cells from a low-biomass, high-volume sample. Over the past decade, cell-sorting detection systems have undergone enhancements and increased sensitivity, making bacterial cell sorting a feasible concept. Although there are many unknown limitations with regard to the applicability of this technology to environmental samples (smaller cells, few cells, mixed populations), dogmatic principles support the theoretical effectiveness of this technique upon thorough testing and proper optimization. Furthermore, the pilot study from which this report is based proved effective and demonstrated this technology capable of sorting and concentrating bacterial endospore and bacterial cells of varying size and morphology. Two commercial off-the-shelf bacterial counting kits were used to optimize a bacterial stain/dye FACS protocol. A LIVE/DEAD BacLight Viability and Counting Kit was used to distinguish between the live and dead cells. A Bacterial Counting Kit comprising SYTO BC (mixture of SYTO dyes) was employed as a broad-spectrum bacterial counting agent. Optimization using epifluorescence microscopy was performed with these two dye/stains. This refined protocol was further validated using varying ratios and mixtures of cells to ensure homogenous staining compared to that of individual cells, and were utilized for flow analyzer and FACS labeling. This technology focuses on the purification and concentration of cells from low-biomass spacecraft assembly facility samples. Currently, purification and concentration of low-biomass samples plague planetary protection downstream analyses. Having a capability to use flow cytometry to concentrate cells out of low-biomass, high-volume spacecraft/ facility sample extracts will be of extreme benefit to the fields of planetary protection and astrobiology. Successful research and development of this novel methodology will significantly increase the knowledge base for designing more effective cleaning protocols, and ultimately lead to a more empirical and true account of the microbial diversity present on spacecraft surfaces. Refined cleaning and an enhanced ability to resolve microbial diversity may decrease the overall cost of spacecraft assembly and/or provide a means to begin to assess challenging planetary protection missions.

Simulating Silicon Photomultiplier Response to Scintillation Light

PubMed Central

Jha, Abhinav K.; van Dam, Herman T.; Kupinski, Matthew A.; Clarkson, Eric

2015-01-01

The response of a Silicon Photomultiplier (SiPM) to optical signals is affected by many factors including photon-detection efficiency, recovery time, gain, optical crosstalk, afterpulsing, dark count, and detector dead time. Many of these parameters vary with overvoltage and temperature. When used to detect scintillation light, there is a complicated non-linear relationship between the incident light and the response of the SiPM. In this paper, we propose a combined discrete-time discrete-event Monte Carlo (MC) model to simulate SiPM response to scintillation light pulses. Our MC model accounts for all relevant aspects of the SiPM response, some of which were not accounted for in the previous models. We also derive and validate analytic expressions for the single-photoelectron response of the SiPM and the voltage drop across the quenching resistance in the SiPM microcell. These analytic expressions consider the effect of all the circuit elements in the SiPM and accurately simulate the time-variation in overvoltage across the microcells of the SiPM. Consequently, our MC model is able to incorporate the variation of the different SiPM parameters with varying overvoltage. The MC model is compared with measurements on SiPM-based scintillation detectors and with some cases for which the response is known a priori. The model is also used to study the variation in SiPM behavior with SiPM-circuit parameter variations and to predict the response of a SiPM-based detector to various scintillators. PMID:26236040

Effects of dietary supplementation of organic chromium (picolinate) on physical and biochemical characteristics of semen and carcass traits of male turkeys.

PubMed

Biswas, Avishek; Divya, Sharma; Mandal, A B; Majumdar, S; Singh, Ram

2014-12-30

This experiment investigated the effect of dietary chromium (Cr as picolinate) on physical and biochemical characteristics of semen and carcass traits of adult male turkey. Seventy-two (72) male turkeys (16 weeks old) were randomly distributed into four dietary treatment groups (4×3×6) for a period of 24 weeks. Three experimental diets were supplemented with 250, 500 and 750μg Cr/kg (T2, T3 and T4 respectively) in basal diet (T1 considered as control). Semen physical characteristics viz. sperm concentration, progressive motility, live and dead count of spermatozoa and fertility differed significantly (P<0.05). Sperm concentration, progressive motility and fertility were higher and dead count was lower in T4 (750μg) group than control (T1) or other dietary treatments (T2 or T3) group. Semen biochemical parameters like creatinine, acid phosphatase (ACP) and alkaline phosphatase (ALP) concentration did not differ significantly among the dietary treatment groups, whereas, total protein, glucose, malondialdehyde (MAD) and cholesterol concentration differed significantly (P<0.05) amongst the treatment groups. Protein and MAD were higher while glucose and cholesterol concentrations were lower in T3 and T4 group than control or T1 group. The shrinkage loss, eviscerated yield, relative weight (as percent of body weight) of breast, thigh and liver improved on supplementation of Cr leading to significantly higher in T4 group in comparison to control. From this study, it could be concluded that supplementation of chromium as chromium picolinate, at 750μg/kg level in diet was beneficial for improving physical characteristics of semen, carcass yield and breast yield of adult male turkeys. However, Cr levels of 500 or 750μg/kg in diet were beneficial for semen biochemical parameters of adult male turkeys. Copyright © 2014 Elsevier B.V. All rights reserved.

An Improved Flow Cytometry Method For Precise Quantitation Of Natural-Killer Cell Activity

NASA Technical Reports Server (NTRS)

Crucian, Brian; Nehlsen-Cannarella, Sandra; Sams, Clarence

2006-01-01

The ability to assess NK cell cytotoxicity using flow cytometry has been previously described and can serve as a powerful tool to evaluate effector immune function in the clinical setting. Previous methods used membrane permeable dyes to identify target cells. The use of these dyes requires great care to achieve optimal staining and results in a broad spectral emission that can make multicolor cytometry difficult. Previous methods have also used negative staining (the elimination of target cells) to identify effector cells. This makes a precise quantitation of effector NK cells impossible due to the interfering presence of T and B lymphocytes, and the data highly subjective to the variable levels of NK cells normally found in human peripheral blood. In this study an improved version of the standard flow cytometry assay for NK activity is described that has several advantages of previous methods. Fluorescent antibody staining (CD45FITC) is used to positively identify target cells in place of membranepermeable dyes. Fluorescent antibody staining of target cells is less labor intensive and more easily reproducible than membrane dyes. NK cells (true effector lymphocytes) are also positively identified by fluorescent antibody staining (CD56PE) allowing a simultaneous absolute count assessment of both NK cells and target cells. Dead cells are identified by membrane disruption using the DNA intercalating dye PI. Using this method, an exact NK:target ratio may be determined for each assessment, including quantitation of NK target complexes. Backimmunoscatter gating may be used to track live vs. dead Target cells via scatter properties. If desired, NK activity may then be normalized to standardized ratios for clinical comparisons between patients, making the determination of PBMC counts or NK cell percentages prior to testing unnecessary. This method provides an exact cytometric determination of NK activity that highly reproducible and may be suitable for routine use in the clinical setting.

A new screening test for toxicity testing of dental materials.

PubMed

Pelka, M; Danzl, C; Distler, W; Petschelt, A

2000-07-01

The development of a micro plate assay for cytotoxicity testing of dental materials based on a bioassay using brine shrimp larvae (artemia salina) as sensitive organisms. Brine shrimp larvae are commonly used for cytotoxicity assays in pharmacology. These larvae are sensitive to toxic substances. The ratio between dead larvae (no motility) and living larvae (high motility) in comparison to a control without any toxic substances is used to estimate the toxicity of the test solutions. The test materials (Arabesk((R)), Solitaire((R)), Pertac((R)) II, Tetric((R)), Herculite((R)) and the compomer materials Dyract((R)), Hytac((R)), Compoglass((R))) were polymerized and consecutively milled. After incubation of 1g in 4ml distilled water at 37 degrees C for 48h, the solid materials were separated by centrifugation. The solutions were equibrilated with NaCl to a salt content of 25g/l. Aliquots of 200microl were distributed in eight micro wells and 50microl of a artemia salina containing (n=8-14) solution were added to each well. As controls eight wells with 250microl salt solution containing a comparable number of brine shrimp were used. At baseline, after 2, 5, 24 and 48h, the dead shrimp were counted using a stereo microscope. Finally all shrimps were sacrificed using Na-acid (5%) and counted to get the number of shrimps per well. All compomers and Solitaire caused 100% brine shrimp lethality after 24h and showed significantly (p<0.01, signed rank test) higher toxicities than the remaining composites. With the exception of Pertac II, all composites showed significantly higher toxic values than the control. Pertac II did not show any differences from the controls used. This new technique has some advantages for toxicity testing of restorative materials, because it can quickly be carried out at low costs. The disadvantage is the high quantity of material used and the low sensitivity.

Are vent crab behavioral preferences adaptations for habitat choice?

PubMed

Dahms, Hans-Uwe; Tseng, Li-Chun; Hwang, Jiang-Shiou

2017-01-01

Hydrothermal vent organisms are adapted to their extreme and patchily distributed habitats. They are expected to have evolved mechanisms that keep them in their specific habitation. Since little is known about the recruitment or habitat selection of HV organisms such as brachyurans, we examined the properties of several hydrothermal vent-associated cues on the behavior of the hydrothermal vent (HV) crab Xenograpsus testudinatus in the laboratory that were contrasted by the offering of non-vent cues. This crab species is endemic and dominates the vent fauna of Turtle Island off the NE coast of Taiwan. HV crabs were separately and in combination offered the following vent-specific cues: (1) sulfuric sediment, (3) air-bubbling, (4) elevated temperature, (5) dead settled zooplankton, (7) other crabs, and (8) shade. The non-vent-specific cues were: (2) quarz sediment, (6) dead fish, (8) light. These cues were provided on either side of a two-choice chamber. The movement of individual crabs was monitored: as initial and final choices, and as the proportion of time the crabs spent in each compartment (resident time). Cues were offered alone and no such cue as a control in the same set-up. Sulfuric sediments and dead fish were significantly more attractive to females, and other crabs irrespective of gender were significantly more attractive to males. When compared to expected distributions, crabs, irrespective of gender, significantly avoided light and tended to select other crabs, air-bubbling, sulfuric sediment, elevated temperature, dead fish, dead zooplankton, and quarz sediments in the order of decreasing importance. Data do not support the hypothesis that dead settled zooplankton was particularly attractive nor that the other gender was selected. A combination of several vent-associated cues (sulfuric sediment, elevated temperature, air-bubbling) facilitated the strongest attraction to the crabs as reflected by all response variables. The 'first choice' responses were always consistent with the side of the choice compartment in which they spent the longest amount of time (resident time), but not with the 'final choice' of crabs, suggesting that the 'resident time' in addition to their 'first choice' is more reliable than just the 'final choice'. The present results provide the first indication that several vent-associated habitat cues function as attractors for HV crabs. Habitat choice is also reflected by crab larval distribution in the field which tend to stay near the bottom not to be carried away from their specific habitat.

[Bacterial biofilms on PVC tubing's inner surface of hemodialysis water treatment system].

PubMed

Yang, Sha; Jia, Ke; Peng, Youming; Liu, Hong; Liu, Yinghong; Chen, Xing; Liu, Fuyou

2009-10-01

To determine the morphology, bacteria and endotoxin content of biofilms on the inner surface of PVC tubes in hemodialysis water treatment system. We dissolved biofilms of segments before and after reverse osmosis machine for bacterial count and identification. We studied biofilm structure of segments before and after reverse osmosis machine with eyes and scanning electron microscope. Biofilms of all 7 segments were dissolved for qualitative and quantitative assay of endotoxin. The inner surface of segment before reverse osmosis machine was homogeneously distributed with activated carbon powder deposition. The segment after reverse osmosis machine was normal. With scanning electron microscope, biofilm with successive surface and sandwich was found on the inner surface of segment before reverse osmosis machine, formed by clustering bacillus, activated carbon powder and some coccus. Bacteria of the same shape and length were found on segment after reverse osmosis machine, but fewer and looser. Bacterial culture and identification showed the former was mostly gram-negative bacillus, the latter was only a few micrococcus. Endotoxin of biofilm was between 2.0 EU/mL and 4.0 EU/mL. Quantitative assay showed: segment after softener (2.821+/-0.807) EU/mL; segment after active charcoal canister(3.635+/-0.427) EU/mL; segment before reverse osmosis machine (3.687+/-0.271) EU/mL; segment after reverse osmosis machine (2.041+/-0.295) EU/mL; exit of power pump (1.983+/-0.390)EU/mL;the 1st dead space (2.373+/-0.535) EU/mL; and the 2nd dead space (2.858+/-0.690)EU/mL. Biofilms are found on the inner surface of segment before and after reverse osmosis machine. Endotoxin level from high to low is as follows: segment before reverse osmosis machine, segment after active charcoal canister, the 2nd dead space, segment after softener, the 1st dead space, segment after reverse osmosis machine, exit of power pump. The character of the bacteria and endotoxin of the biofilm can help us find better ways to control them.

New perspectives on interdisciplinary earth science at the Dead Sea: The DESERVE project.

PubMed

Kottmeier, Christoph; Agnon, Amotz; Al-Halbouni, Djamil; Alpert, Pinhas; Corsmeier, Ulrich; Dahm, Torsten; Eshel, Adam; Geyer, Stefan; Haas, Michael; Holohan, Eoghan; Kalthoff, Norbert; Kishcha, Pavel; Krawczyk, Charlotte; Lati, Joseph; Laronne, Jonathan B; Lott, Friederike; Mallast, Ulf; Merz, Ralf; Metzger, Jutta; Mohsen, Ayman; Morin, Efrat; Nied, Manuela; Rödiger, Tino; Salameh, Elias; Sawarieh, Ali; Shannak, Benbella; Siebert, Christian; Weber, Michael

2016-02-15

The Dead Sea region has faced substantial environmental challenges in recent decades, including water resource scarcity, ~1m annual decreases in the water level, sinkhole development, ascending-brine freshwater pollution, and seismic disturbance risks. Natural processes are significantly affected by human interference as well as by climate change and tectonic developments over the long term. To get a deep understanding of processes and their interactions, innovative scientific approaches that integrate disciplinary research and education are required. The research project DESERVE (Helmholtz Virtual Institute Dead Sea Research Venue) addresses these challenges in an interdisciplinary approach that includes geophysics, hydrology, and meteorology. The project is implemented by a consortium of scientific institutions in neighboring countries of the Dead Sea (Israel, Jordan, Palestine Territories) and participating German Helmholtz Centres (KIT, GFZ, UFZ). A new monitoring network of meteorological, hydrological, and seismic/geodynamic stations has been established, and extensive field research and numerical simulations have been undertaken. For the first time, innovative measurement and modeling techniques have been applied to the extreme conditions of the Dead Sea and its surroundings. The preliminary results show the potential of these methods. First time ever performed eddy covariance measurements give insight into the governing factors of Dead Sea evaporation. High-resolution bathymetric investigations reveal a strong correlation between submarine springs and neo-tectonic patterns. Based on detailed studies of stratigraphy and borehole information, the extension of the subsurface drainage basin of the Dead Sea is now reliably estimated. Originality has been achieved in monitoring flash floods in an arid basin at its outlet and simultaneously in tributaries, supplemented by spatio-temporal rainfall data. Low-altitude, high resolution photogrammetry, allied to satellite image analysis and to geophysical surveys (e.g. shear-wave reflections) has enabled a more detailed characterization of sinkhole morphology and temporal development and the possible subsurface controls thereon. All the above listed efforts and scientific results take place with the interdisciplinary education of young scientists. They are invited to attend joint thematic workshops and winter schools as well as to participate in field experiments. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

DNA-carbon nano onion aggregate: triangle, hexagon, six-petal flower to dead-end network

NASA Astrophysics Data System (ADS)

Babar, Dipak Gorakh; Pakhira, Bholanath; Sarkar, Sabyasachi

2017-08-01

The interaction between calf-thymus (CT) dsDNA and water soluble carbon nano onion (wsCNO) in water follows denaturation of dsDNA (double stranded) to ssDNA (single stranded) as monitored by optical spectroscopy. The ssDNA concomitantly wraps the spiky surface of wsCNO to create triangular aggregate as the building block as observed by time-dependent SEM images. These triangles further aggregate leading to six-petal flower arrangement via hexagon and finally reach a dead end network as imaged by SEM and optical fluorescence microscopy. The dead-end network aggregate lost the intrinsic optical property of DNA suggesting complete loss of its activity.

Stabilization and analytical tuning rule of double-loop control scheme for unstable dead-time process

NASA Astrophysics Data System (ADS)

Ugon, B.; Nandong, J.; Zang, Z.

2017-06-01

The presence of unstable dead-time systems in process plants often leads to a daunting challenge in the design of standard PID controllers, which are not only intended to provide close-loop stability but also to give good performance-robustness overall. In this paper, we conduct stability analysis on a double-loop control scheme based on the Routh-Hurwitz stability criteria. We propose to use this unstable double-loop control scheme which employs two P/PID controllers to control first-order or second-order unstable dead-time processes typically found in process industries. Based on the Routh-Hurwitz stability necessary and sufficient criteria, we establish several stability regions which enclose within them the P/PID parameter values that guarantee close-loop stability of the double-loop control scheme. A systematic tuning rule is developed for the purpose of obtaining the optimal P/PID parameter values within the established regions. The effectiveness of the proposed tuning rule is demonstrated using several numerical examples and the result are compared with some well-established tuning methods reported in the literature.

Comparison of the performance of different instruments in the stray neutron field around the CERN Proton Synchrotron.

PubMed

Aza, Eleni; Caresana, Marco; Cassell, Christopher; Colombo, Valeria; Damjanovic, Sanja; Gilardoni, Simone; Manessi, Giacomo Paolo; Pangallo, Michel; Perrin, Daniel; Silari, Marco

2014-10-01

This paper discusses an intercomparison campaign carried out in several locations around the CERN Proton Synchrotron. The locations were selected in order to perform the measurements in different stray field conditions. Various neutron detectors were employed: ionisation chambers, conventional and extended range rem counters, both commercial and prototype ones, including a novel instrument called LUPIN, specifically conceived to work in pulsed fields. The attention was focused on the potential differences in the instrument readings due to dead-time losses that are expected to affect most commercial units. The results show that the ionisation chambers and LUPIN agree well with the expected H*(10) values, as derived from FLUKA simulations, showing no relevant underestimations even in strongly pulsed fields. On the contrary, the dead-time losses of the other rem counters induced an underestimation in pulsed fields that was more important for instruments characterised by a higher dead time. © The Author 2013. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

MAGNETIZED ACCRETION AND DEAD ZONES IN PROTOSTELLAR DISKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dzyurkevich, Natalia; Henning, Thomas; Turner, Neal J.

The edges of magnetically dead zones in protostellar disks have been proposed as locations where density bumps may arise, trapping planetesimals and helping form planets. Magneto-rotational turbulence in magnetically active zones provides both accretion of gas on the star and transport of mass to the dead zone. We investigate the location of the magnetically active regions in a protostellar disk around a solar-type star, varying the disk temperature, surface density profile, and dust-to-gas ratio. We also consider stellar masses between 0.4 and 2 M{sub Sun }, with corresponding adjustments in the disk mass and temperature. The dead zone's size andmore » shape are found using the Elsasser number criterion with conductivities including the contributions from ions, electrons, and charged fractal dust aggregates. The charged species' abundances are found using the approach proposed by Okuzumi. The dead zone is in most cases defined by the ambipolar diffusion. In our maps, the dead zone takes a variety of shapes, including a fish tail pointing away from the star and islands located on and off the midplane. The corresponding accretion rates vary with radius, indicating locations where the surface density will increase over time, and others where it will decrease. We show that density bumps do not readily grow near the dead zone's outer edge, independently of the disk parameters and the dust properties. Instead, the accretion rate peaks at the radius where the gas-phase metals freeze out. This could lead to clearing a valley in the surface density, and to a trap for pebbles located just outside the metal freezeout line.« less

The deeper structure of the southern Dead Sea basin derived from neural network analysis of velocity and attenuation tomography

NASA Astrophysics Data System (ADS)

Braeuer, Benjamin; Haberland, Christian; Bauer, Klaus; Weber, Michael

2014-05-01

The Dead Sea basin is a pull-apart basin at the Dead Sea transform fault, the boundary between the African and the Arabian plates. Though the DSB has been studied for a long time, the available knowledge - based mainly on surface geology, drilling and seismic reflection surveys - gives only a partial picture of its shallow structure. Therefore, within the framework of the international DESIRE (DEad Sea Integrated REsearch) project, a dense temporary local seismological network was operated in the southern Dead Sea area. Within 18 month of recording 650 events were detected. In addition to an already published tomography study revealing the distribution of P velocities and the Vp/Vs ratios a 2D P-wave attenuation tomography (parameter Qp) was performed. The neural network technique of Self-organizing maps (SOM) is used for the joint interpretation of these three parameters (Vp, Vp/Vs, Qp). The resulting clusters in the petrophysical parameter space are assigned to the main lithological units below the southern part of the Dead Sea basin: (1) The basin sediments characterized by strong attenuation, high vp/vs ratios and low P velocities. (2) The pre-basin sediments characterized by medium to strong attenuation, low Vp/Vs ratios and medium P velocities. (3) The basement characterized by low to moderate attenuation, medium vp/vs ratios and high P velocities. Thus, the asymmetric southern Dead Sea basin is filled with basin sediments down to depth of 7 to 12 km. Below the basin sediments, the pre-basin sediments are extending to a depth between 13 and 18 km.

Count-doubling time safety circuit

DOEpatents

Rusch, Gordon K.; Keefe, Donald J.; McDowell, William P.

1981-01-01

There is provided a nuclear reactor count-factor-increase time monitoring circuit which includes a pulse-type neutron detector, and means for counting the number of detected pulses during specific time periods. Counts are compared and the comparison is utilized to develop a reactor scram signal, if necessary.

Morphological observation and analysis using automated image cytometry for the comparison of trypan blue and fluorescence-based viability detection method.

PubMed

Chan, Leo Li-Ying; Kuksin, Dmitry; Laverty, Daniel J; Saldi, Stephanie; Qiu, Jean

2015-05-01

The ability to accurately determine cell viability is essential to performing a well-controlled biological experiment. Typical experiments range from standard cell culturing to advanced cell-based assays that may require cell viability measurement for downstream experiments. The traditional cell viability measurement method has been the trypan blue (TB) exclusion assay. However, since the introduction of fluorescence-based dyes for cell viability measurement using flow or image-based cytometry systems, there have been numerous publications comparing the two detection methods. Although previous studies have shown discrepancies between TB exclusion and fluorescence-based viability measurements, image-based morphological analysis was not performed in order to examine the viability discrepancies. In this work, we compared TB exclusion and fluorescence-based viability detection methods using image cytometry to observe morphological changes due to the effect of TB on dead cells. Imaging results showed that as the viability of a naturally-dying Jurkat cell sample decreased below 70 %, many TB-stained cells began to exhibit non-uniform morphological characteristics. Dead cells with these characteristics may be difficult to count under light microscopy, thus generating an artificially higher viability measurement compared to fluorescence-based method. These morphological observations can potentially explain the differences in viability measurement between the two methods.

Transportation impacts to wildlife on state route 37 in northern San Pablo Bay, California

USGS Publications Warehouse

Winton, Bryan R.; Takekawa, John Y.

2002-01-01

State Route 37 bisects conservation lands managed by San Pablo Bay National Wildlife Refuge (U.S. Fish & Wildlife Service) and Napa-Sonoma Marshes Wildlife Area (California Department of Fish and Game) in Solano and Sonoma Counties. The 2-lane highway connects Interstates 101 and 80 in northern San Francisco Bay and experiences ~26,000 vehicles per day. Road-killed wildlife between Napa River and Tolay Creek bridges (14.7 km) were counted in 2000 to ascertain species composition, relative abundance, and relative occurence (animal fatality interval). The primary objectives of the study were to determine if endangered salt marsh harvest mice (Reithrodontomys raviventris), California clapper rails (Rallus longirostris), or other species of concern were represented, and to collect baseline data on transportation impacts to wildlife in the area. During 51 surveys, 291 dead birds (54.6%) and mammals (45.4%) were observed. Endangered species were not positively identified dead on the highway. In total, 28 bird, 10 mammal and 1 reptile species were positively identified along this section of highway that traverses tidal marsh and diked baylands (i.e., salt ponds, seasonal wetlands, and oat-hay agriculture fields). The mean animal fatality interval for both lanes was one road-kill every 2.1km (2.1 km SD).

Estimation of lactic acid bacterial cell number by DNA quantification.

PubMed

Ishii, Masaki; Matsumoto, Yasuhiko; Sekimizu, Kazuhisa

2018-01-01

Lactic acid bacteria are provided by fermented foods, beverages, medicines, and supplements. Because the beneficial effects of medicines and supplements containing functional lactic acid bacteria are related to the bacterial cell number, it is important to establish a simple method for estimating the total number of lactic acid bacterial cells in the products for quality control. Almost all of the lactic acid bacteria in the products are dead, however, making it difficult to estimate the total number of lactic acid bacterial cells in the products using a standard colony-counting method. Here we estimated the total lactic acid bacterial cell number in samples containing dead bacteria by quantifying the DNA. The number of viable Enterococcus faecalis 0831-07 cells decreased to less than 1 × 10 -8 by 15 min of heat treatment at 80°C. The amount of extracted DNA from heat-treated cells was 78% that of non-heated cells. The number of viable Lactobacillus paraplantarum 11-1 cells decreased to 1 × 10 -4 after 4 days culture. The amount of extracted DNA of the long-cultured cells, however, was maintained at 97%. These results suggest that cell number of lactic acid bacteria killed by heat-treatment or long-term culture can be estimated by DNA quantification.

Antimicrobial Effects of Dental Luting Glass Ionomer Cements on Streptococcus mutans

PubMed Central

Altenburger, Markus; Spitzmüller, Bettina; Anderson, Annette; Hellwig, Elmar

2014-01-01

Objective. To reduce secondary caries, glass ionomer luting cements are often used for cementing of indirect restorations. This is because of their well-known antimicrobial potential through the release of fluoride ions. The aim of this in vitro study was to investigate the antimicrobial effect of five dental luting cements which were based on glass ionomer cement technology. Methods. Five different glass ionomer based luting cements were tested for their antimicrobial effects on Streptococcus mutans in two different experimental setups: (i) determination of colony-forming units (CFUs) in a plate-counting assay; (ii) live/dead staining (LDS) and fluorescence microscopy. All experiments were conducted with or without prior treatment of the materials using sterilized human saliva. Antimicrobial effects were evaluated for adherent and planktonic bacteria. Bovine enamel slabs (BES) were used as negative control. BES covered with 0.2% chlorhexidine (CHX) served as positive control. Results. Each of the tested materials significantly reduced the number of initially adhered CFUs; this reduction was even more pronounced after prior incubation in saliva. Antimicrobial effects on adherent bacteria were confirmed by live-dead staining. Conclusion. All five luting cements showed an antimicrobial potential which was increased by prior incubation with human saliva, suggesting an enhanced effect in vivo. PMID:24795539

Confocal microscopy and 3-D distribution of dead cells in cryopreserved pancreatic islets

NASA Astrophysics Data System (ADS)

Merchant, Fatima A.; Aggarwal, Shanti J.; Diller, Kenneth R.; Bartels, Keith A.; Bovik, Alan C.

1992-06-01

Our laboratory is involved in studies of changes in shape and size of biological specimens under osmotic stress at ambient and sub-zero temperatures. This paper describes confocal microscopy, image processing and analysis of 3-D distribution of cells in acridine orange/propidium iodide (AO/PI) fluorescent stained frozen-thawed islet of Langerhans. Isolated and cultured rat pancreatic islets were frozen and thawed in 2 M dimethylsulfoxide and examined under a Zeiss laser scanning confocal microscope. Two micrometers to five micrometers serial sections of the islets were obtained and processed to obtain high contrast images which were later processed in two steps. The first step consisted of the isolation of the region of interest by template masking followed by grey level thresholding to obtain a binary image. Three-dimensional blob coloring algorithm was applied and the number of voxels in each region and the number of regions were counted. The volumetric distribution of the dead cells in the islets was computed by calculating the distance from the center of each blob to the centroid of the 3-D image. An increase in the number of blobs moving from the center toward the periphery of the islet was observed indicating that the freeze damage was more concentrated in the outer edges of the islet.

One life ends, another begins: Management of a brain-dead pregnant mother-A systematic review-

PubMed Central

2010-01-01

Background An accident or a catastrophic disease may occasionally lead to brain death (BD) during pregnancy. Management of brain-dead pregnant patients needs to follow special strategies to support the mother in a way that she can deliver a viable and healthy child and, whenever possible, also be an organ donor. This review discusses the management of brain-dead mothers and gives an overview of recommendations concerning the organ supporting therapy. Methods To obtain information on brain-dead pregnant women, we performed a systematic review of Medline, EMBASE and the Cochrane Central Register of Controlled Trials (CENTRAL). The collected data included the age of the mother, the cause of brain death, maternal medical complications, gestational age at BD, duration of extended life support, gestational age at delivery, indication of delivery, neonatal outcome, organ donation of the mothers and patient and graft outcome. Results In our search of the literature, we found 30 cases reported between1982 and 2010. A nontraumatic brain injury was the cause of BD in 26 of 30 mothers. The maternal mean age at the time of BD was 26.5 years. The mean gestational age at the time of BD and the mean gestational age at delivery were 22 and 29.5 weeks, respectively. Twelve viable infants were born and survived the neonatal period. Conclusion The management of a brain-dead pregnant woman requires a multidisciplinary team which should follow available standards, guidelines and recommendations both for a nontraumatic therapy of the fetus and for an organ-preserving treatment of the potential donor. PMID:21087498

Which Donor for Uterus Transplants: Brain-Dead Donor or Living Donor? A Systematic Review.

PubMed

Lavoué, Vincent; Vigneau, Cécile; Duros, Solène; Boudjema, Karim; Levêque, Jean; Piver, Pascal; Aubard, Yves; Gauthier, Tristan

2017-02-01

The aim of this systematic review was to evaluate and compare the pros and cons of using living donors or brain-dead donors in uterus transplantation programs, 2 years after the first worldwide live birth after uterus transplantation. The Medline database and the Central Cochrane Library were used to locate uterine transplantation studies carried out in human or nonhuman primates. All types of articles (case reports, original studies, meta-analyses, reviews) in English or French were considered for inclusion. Overall, 92 articles were screened and 44 were retained for review. Proof of concept for human uterine transplantation was demonstrated in 2014 with a living donor. Compared with a brain-dead donor strategy, a living donor strategy offers greater possibilities for planning surgery and also decreases cold ischemia time, potentially translating into a higher success rate. However, this approach poses ethical problems, given that the donor is exposed to surgery risks but does not derive any direct benefit. A brain-dead donor strategy is more acceptable from an ethical viewpoint, but its feasibility is currently unproven, potentially owing to a lack of compatible donors, and is associated with a longer cold ischemia time and a potentially higher rejection rate. The systematic review demonstrates that uterine transplantation is a major surgical innovation for the treatment of absolute uterine factor infertility. Living and brain-dead donor strategies are not mutually exclusive and, in view of the current scarcity of uterine grafts and the anticipated future rise in demand, both will probably be necessary.

Did the ever dead outnumber the living and when? A birth-and-death approach

NASA Astrophysics Data System (ADS)

Avan, Jean; Grosjean, Nicolas; Huillet, Thierry

2015-02-01

This paper is an attempt to formalize analytically the question raised in 'World Population Explained: Do Dead People Outnumber Living, Or Vice Versa?' Huffington Post, Howard (2012). We start developing simple deterministic Malthusian growth models of the problem (with birth and death rates either constant or time-dependent) before running into both linear birth and death Markov chain models and age-structured models.

Quantifying surface water runoff from Wadi Arogut towards the Dead Sea

NASA Astrophysics Data System (ADS)

Geyer, Stefan; Khayat, Saed; Marei, Amer

2015-04-01

The surrounded area of the Dead Sea, especially the west side suffers from many hydrological problems. While the Dead Sea level drop considered a major problem that affect the quality of the surrounded freshwater resources, a lot of the surface water flood from the adjacent Wadi are lost through direct run off without any exploitation. Therefore, it is necessary to maintain a type of balance between surface water exploitation through the Wadi and at the same time allow a sufficient amount of flow to the Dead Sea to ensure its sustainability. In this study, we choose one of the larger tributaries in the western side of the Dead Sea basin. The stream was modelled for runoff response to different rainfall amount and climate conditions (dry, normal, and wet seasons) which were chosen from the rainy seasons in the previous 30 years. Finally, the amount of surface water contribution from each of the three seasons of the Dead Sea was quantified. The outcome of the model shows the results from the normal rainy season, which is frequently reoccurs and common in the region. The model data show that such events normally contribute with about 18-22 MCM annually to the Dead Sea. The problem is with the recurrence of dry season such as 2005/2006, by which the amount of the surface water decrease and consequently has adverse effect on the Dead Sea. However, the presence of less frequent thunder storm season such as that one in 1991/1992 has also a positive effect on the Dead Sea level. In the rainy season 1991/1992 there was a higher amount of rainfall over the study area that reaches around 155 MCM. Despite the presence of this high amount most of the recharge lost to the ground as groundwater recharge. The high amount of rain increases the amount of inundated surface water out of the Wadi banks and covers more surfaces all over the study area, which in role promote more water loss to the ground. That is why the total loss (rather than surface runoff) was much higher (77%). Moreover, 50% less precipitation in 2006 decrease the Dead Sea five metres within five years, and 60% 1992 increase of precipitation raise the water level two metre only for two to three next years. How can we balance the groundwater needs and the Dead Sea survival with those 40% surface water? By no mean: preventing the Dead Sea decline by increasing runoff will not only preventing the fresh water deterioration, but also it will be in the account of groundwater recharge in the surrounding aquifers of the Dead Sea. These conclusions suggest strongly the need of an integrated groundwater model, in order to quantify all scenarios.

A dual mode breath sampler for the collection of the end-tidal and dead space fractions.

PubMed

Salvo, P; Ferrari, C; Persia, R; Ghimenti, S; Lomonaco, T; Bellagambi, F; Di Francesco, F

2015-06-01

This work presents a breath sampler prototype automatically collecting end-tidal (single and multiple breaths) or dead space air fractions (multiple breaths). This result is achieved by real time measurements of the CO2 partial pressure and airflow during the expiratory and inspiratory phases. Suitable algorithms, used to control a solenoid valve, guarantee that a Nalophan(®) bag is filled with the selected breath fraction even if the subject under test hyperventilates. The breath sampler has low pressure drop (<0.5 kPa) and uses inert or disposable components to avoid bacteriological risk for the patients and contamination of the breath samples. A fully customisable software interface allows a real time control of the hardware and software status. The performances of the breath sampler were evaluated by comparing (a) the CO2 partial pressure calculated during the sampling with the CO2 pressure measured off-line within the Nalophan(®) bag; (b) the concentrations of four selected volatile organic compounds in dead space, end-tidal and mixed breath fractions. Results showed negligible deviations between calculated and off-line CO2 pressure values and the distributions of the selected compounds into dead space, end-tidal and mixed breath fractions were in agreement with their chemical-physical properties. Copyright © 2015. Published by Elsevier Ltd.

Age depth model construction of the upper section of ICDP Dead Sea Deep Drilling Project based on the high-resolution 14C dating

NASA Astrophysics Data System (ADS)

Kitagawa, H.; Nakamura, T.; Neugebauer, I.; Schwab, M. J.; Brauer, A.; Goldstein, S. L.; Stein, M.

2014-12-01

To reconstruct environmental, climatic and tectonic histories of the Levant, a deep drilling has been accomplished in the northern basin of the Dead Sea during the fall winter of 2010-2011 by the Dead Sea Deep Drilling Project (DSDDP) in the framework of the ICDP program. The sediment cores from site 5017-1 (water depth of ~300 m) recorded the paleoenvironmental and paleohydrological changes in the Dead Sea and the Levant during the last two glacial-interglacial cycles (Neugebauer et al., QSR in press). To provide precise timing of sedimentological - limnological events in the lake and its watershed, and more critically the relative timing of these events, radiocarbon dating of >70 well-preserved terrestrial plants and some carbonate deposits from the upper 150 m long section of the sediment core were performed. Based on the high-resolution radiocarbon dating, a statistical age-depth model was constructed with assumptions on the deposition condition and the radiocarbon age offset of carbonate samples. We discuss the practicality and the limitation of the age-depth model toward interpreting the high-resolution records of environmental, climatic and tectonic events recorded in the long sediment cores from site 5017-1.

Wavelet-based tracking of bacteria in unreconstructed off-axis holograms.

PubMed

Marin, Zach; Wallace, J Kent; Nadeau, Jay; Khalil, Andre

2018-03-01

We propose an automated wavelet-based method of tracking particles in unreconstructed off-axis holograms to provide rough estimates of the presence of motion and particle trajectories in digital holographic microscopy (DHM) time series. The wavelet transform modulus maxima segmentation method is adapted and tailored to extract Airy-like diffraction disks, which represent bacteria, from DHM time series. In this exploratory analysis, the method shows potential for estimating bacterial tracks in low-particle-density time series, based on a preliminary analysis of both living and dead Serratia marcescens, and for rapidly providing a single-bit answer to whether a sample chamber contains living or dead microbes or is empty. Copyright © 2017 Elsevier Inc. All rights reserved.

A study on evaluation of the dependences of the function and the shape in a 99 m Tc-DMSA renal scan on the difference in acquisition count

NASA Astrophysics Data System (ADS)

Dong, Kyung-Rae; Shim, Dong-Oh; Kim, Ho-Sung; Park, Yong-Soon; Chung, Woon-Kwan; Cho, Jae-Hwan

2013-02-01

In a nuclear medicine examination, methods to acquire a static image include the preset count method and the preset time method. The preset count method is used mainly in a static renal scan that utilizes 99 m Tc-DMSA (dimoercaptosuccinic acid) whereas the preset time method is used occasionally. When the preset count method is used, the same number of acquisition counts is acquired for each time, but the scan time varies. When the preset time method is used, the scan time is constant, but the number of counts acquired is not the same. Therefore, this study examined the dependence of the difference in information on the function and the shape of both sides of the kidneys on the counts acquired during a renal scan that utilizes 99 m Tc-DMSA. The study involved patients who had 40-60% relative function of one kidney among patients who underwent a 99 m Tc-DMSA renal scan in the Nuclear Medicine Department during the period from January 11 to March 31, 2012. A gamma camera was used to obtain the acquisition count continuously using 100,000 counts and 300,000 counts, and an acquisition time of 7 minutes (exceeding 300,000 counts). The function and the shape of the kidney were evaluated by measuring the relative function of both sides of the kidneys, the geometric mean, and the size of kidney before comparative analysis. According to the study results, neither the relative function nor the geometric mean of both sides of the kidneys varied significantly with the acquisition count. On the other hand, the size of the kidney tended to be larger with increasing acquisition count.

Responses to the 2800 years BP climatic oscillation in shallow- and deep-basin sediments from the Dead Sea

NASA Astrophysics Data System (ADS)

Neugebauer, Ina; Brauer, Achim; Schwab, Markus; Dulski, Peter; Frank, Ute; Hadzhiivanova, Elitsa; Kitagawa, Hiroyuki; Litt, Thomas; Schiebel, Vera; Taha, Nimer; Waldmann, Nicolas

2015-04-01

Laminated lake sediments from the Dead Sea basin provide high-resolution records of climatic variability in the eastern Mediterranean region, which is considered being especially sensitive to changing climatic conditions. In the study presented here, we aim to reconstruct palaeoclimatic changes and their relation to the frequency of flood/erosion and dust deposition events as archived in the Dead Sea basin for the time interval from ca 3700 to 1700 years BP. A ca 4 m thick, mostly annually laminated (varved) sediment section from the western margin of the Dead Sea (shallow-water DSEn - Ein Gedi profile) was analysed and correlated to the new ICDP Dead Sea Deep Drilling Project core 5017-1 from the deep basin. To detect even single event layers, we applied a multi-proxy approach of high-resolution microscopic thin section analyses, µXRF element scanning and magnetic susceptibility measurements, supported by grain size and palynological analyses. Based on radiocarbon and varve dating two pronounced dry periods were detected at ~3500-3300 yrs BP and ~2900-2400 yrs BP that are characterized by a sand deposit during the older dry period and enhanced frequency of coarse detrital layers during the younger dry period in the shallow-water DSEn core, both interpreted as increased erosion processes. In the 5017-1 deep-basin core these dry periods are depicted by halite deposits. The timing of the younger dry period broadly coincides with the Homeric Minimum of solar activity at ca 2800 yrs BP. Our results suggest that during this period the Dead Sea region experienced a change in synoptic weather patterns leading to an increased occurrence of flash-flood events, overprinting the overall dry climatic conditions. Following this dry spell, a 250-yrs period of increased dust deposition is observed, coinciding with more regular aragonite precipitation during less arid climatic conditions.

Bio-removal of Nickel ions by Sporosarcina pasteurii and Bacillus megaterium, A Comparative Study

NASA Astrophysics Data System (ADS)

Gheethi, AA; Efaq, AN; Mohamed, RM; Abdel-Monem, MO; Halid Abdullah, Abd; Hashim, M. Amir

2017-08-01

The aim of this work was to study the potential of Sporosarcina pasteurii 586S and Bacillus megaterium 1295S isolated from sewage treatment plants (STPs) in removing of nickel ions from the aqueous solution. The bacterial cells were used as living and dead cell biomass. The efficiency of bio-removal process was investigated as a response for nickel and biomass concentrations, time, pH and temperature. The bio-removal capacity (Qmax) of both strains were compared. The highest bio-removal percentage was recorded by dead cells in comparison to living cells. Dead cell biomass of B. megaterium 1295S exhibited higher efficiency for bio-removing of Ni2+ than S. pasteurii 586S at196.4 and 200.2 mg Ni2+ g-1, respectively. It can be concluded that both bacterial strains have high potential to be applied in the biotechnology for removing of Ni2+ ions, however, dead cells of B. megaterium 1295S is the most potent.

Development of PMA real-time PCR method to quantify viable cells of Pantoea agglomerans CPA-2, an antagonist to control the major postharvest diseases on oranges.

PubMed

Soto-Muñoz, Lourdes; Teixidó, Neus; Usall, Josep; Viñas, Inmaculada; Crespo-Sempere, Ana; Torres, Rosario

2014-06-16

Dilution plating is the quantification method commonly used to estimate the population level of postharvest biocontrol agents, but this method does not permit a distinction among introduced and indigenous strains. Recently, molecular techniques based on DNA amplification such as quantitative real-time PCR (qPCR) have been successfully applied for their high strain-specific detection level. However, the ability of qPCR to distinguish viable and nonviable cells is limited. A promising strategy to avoid this issue relies on the use of nucleic acid intercalating dyes, such as propidium monoazide (PMA), as a sample pretreatment prior to the qPCR. The objective of this study was to optimize a protocol based on PMA pre-treatment samples combined with qPCR to distinguish and quantify viable cells of the biocontrol agent P. agglomerans CPA-2 applied as a postharvest treatment on orange. The efficiency of PMA-qPCR method under the established conditions (30μM PMA for 20min of incubation followed by 30min of LED light exposure) was evaluated on an orange matrix. Results showed no difference in CFU or cells counts of viable cells between PMA-qPCR and dilution plating. Samples of orange matrix inoculated with a mixture of viable/dead cells showed 5.59log10 CFU/ml by dilution plating, 8.25log10 cells/ml by qPCR, and 5.93log10 cells/ml by PMA-qPCR. Furthermore, samples inoculated with heat-killed cells were not detected by dilution plating and PMA-qPCR, while by qPCR was of 8.16log10 cells/ml. The difference in quantification cycles (Cq) among qPCR and PMA-qPCR was approximately 16cycles, which means a reduction of 65,536 fold of the dead cells detected. In conclusion, PMA-qPCR method is a suitable tool for quantify viable CPA-2 cells, which could be useful to estimate the ability of this antagonist to colonize the orange surface. Copyright © 2014 Elsevier B.V. All rights reserved.

Factors affecting fall down rates of dead aspen (Populus tremuloides) biomass following severe drought in west-central Canada.

PubMed

Ted Hogg, Edward H; Michaelian, Michael

2015-05-01

Increases in mortality of trembling aspen (Populus tremuloides Michx.) have been recorded across large areas of western North America following recent periods of exceptionally severe drought. The resultant increase in standing, dead tree biomass represents a significant potential source of carbon emissions to the atmosphere, but the timing of emissions is partially driven by dead-wood dynamics which include the fall down and breakage of dead aspen stems. The rate at which dead trees fall to the ground also strongly influences the period over which forest dieback episodes can be detected by aerial surveys or satellite remote sensing observations. Over a 12-year period (2000-2012), we monitored the annual status of 1010 aspen trees that died during and following a severe regional drought within 25 study areas across west-central Canada. Observations of stem fall down and breakage (snapping) were used to estimate woody biomass transfer from standing to downed dead wood as a function of years since tree death. For the region as a whole, we estimated that >80% of standing dead aspen biomass had fallen after 10 years. Overall, the rate of fall down was minimal during the year following stem death, but thereafter fall rates followed a negative exponential equation with k = 0.20 per year. However, there was high between-site variation in the rate of fall down (k = 0.08-0.37 per year). The analysis showed that fall down rates were positively correlated with stand age, site windiness, and the incidence of decay fungi (Phellinus tremulae (Bond.) Bond. and Boris.) and wood-boring insects. These factors are thus likely to influence the rate of carbon emissions from dead trees following periods of climate-related forest die-off episodes. © 2014 Her Majesty the Queen in Right of Canada Global Change Biology © 2014 John Wiley & Sons Ltd Reproduced with the permission of the Minister of Natural Resources Canada.

An ever-changing ecological battlefield: marijuana cultivation and toxicant use in western forests

Treesearch

Craig M. Thompson; Mourad W  Gabriel; Kathryn L. Purcell

2017-01-01

Frozen in the act of scavenging dinner, the vulture’s head lay on the fox’s abdomen, covering the hole it had been attempting to enlarge. When biologists pulled the bird away, they found not only a healthy looking, though dead, fox underneath, but also scores of insects scattered around. Less than a mile away the scene was repeated. This time the dead animal...

Comparison of capnovolumetry-derived dead space parameters with pulmonary function test in normal adults using histamine provocation.

PubMed

Sun, Xiaoli; Zhang, Yan; Yang, Wenlan; Liu, Jinming

2015-04-01

This study in healthy adults was conducted to explore the clinical application of capnovolumetric indices as compared to lung function parameters using histamine provocation. Forty healthy subjects received aerosol histamine or salbutamol in an automatic stimulation system with escalating doses of histamine. Dead space volumes of capnovolumetry and lung function parameters were examined with increased concentrations of histamine at a fixed time interval. The doses of histamine were selected from 0.0562 mg-2.2 mg and 0.1 mg salbutamol was inhaled when a maximal dose of histamine was reached. Baseline values in each group were calculated prior to histamine inhalation. Fowler dead space (VDF), Wolff dead space (VDW), threshold dead space (VDT), Bohr dead space (VDB), forced expiratory volume in 1 s (FEV1 ) and peak expiratory flow (PEF) showed a dose-dependent reduction following histamine provocation, but there were no statistical differences in the measurements at baseline and post S6 provocation. The value of dC3/DV at the maximal dose was significantly increased over its baseline value (P < 0.05). VDF, VDT and VDW were significantly increased after bronchodilator use (P < 0.05 or <0.01). The changes in capnovolumetry did not correspond with the results of lung function test. The dC3/DV and airway dead spaces of capnovolumetry in healthy adults are significantly increased compared to lung function parameters before or after bronchodilator use, suggesting that capnovolumetry is feasible in diagnostic evaluation of airway reactivity, especially for persons who are unable to undertake lung function test. © 2014 John Wiley & Sons Ltd.

Live/Dead Comparisons of Ostracodes in Temperate Lakes Reveal Evidence of Human Impact and Provides a Tool to Measure the Progress of Remediation Efforts

NASA Astrophysics Data System (ADS)

Spergel, J.; Kimball, K. C.; Fitzpatrick, S. A.; Michelson, A. V.; Leonard-Pingel, J.

2015-12-01

Lake ecosystems face a multitude of environmental threats including: eutrophication, overfishing, and heavy metal pollution. Tools to identify lakes impacted by human activity and quantify that impact are needed to combat their environmental degradation. One such promising tool has been the comparison between living communities and associated time-averaged death assemblages of mollusks in marine environments. Here we extend the reach of such live/dead comparisons using ostracodes in temperate lakes. We sampled six lakes in Wisconsin for living communities and associated death assemblages of ostracodes: two lakes impacted by human activity, two relatively "pristine" lakes, and two remediated lakes. We took sixteen grab samples of the upper centimeter of sediment in each lake, capturing simultaneously living benthic ostracodes and discarded valves of dead ostracodes. We found that impacted lakes had lower live/dead fidelity in taxonomic composition and rank-order abundance distributions and greater within-lake variation in death assemblages than "pristine" lakes. Additionally, the living communities in the impacted lakes tended to be lower in species richness and have lower evenness than "pristine" lakes. Remediated lakes displayed similar live/dead fidelity in taxonomic composition and rank-abundance distributions to "pristine" lakes and had lower within-lake variation in death assemblages than impacted lakes. Remediated lakes also contained living communities that tended to be richer and more even than impacted lakes. The lower live/dead fidelity of ostracodes in impacted lakes indicate live/dead ostracode comparisons can provide a tool to identify lake ecosystems impacted by humans. The similar results of remediated and "pristine" lakes indicate remediation efforts in these lakes have been successful in alleviating environmental impact detrimental to ostracode communities. This result indicates live/dead comparisons of ostracodes can be a useful tool to monitor the progress of remediation efforts already underway. Further work will focus on dating the upper centimeter of sediment in these lakes to provide an estimate of how long it takes for death assemblages to accumulate and thus how long it will take to regain high live/dead fidelity in impacted lakes undergoing remediation.

An experimental test of the habitat-amount hypothesis for saproxylic beetles in a forested region.

PubMed

Seibold, Sebastian; Bässler, Claus; Brandl, Roland; Fahrig, Lenore; Förster, Bernhard; Heurich, Marco; Hothorn, Torsten; Scheipl, Fabian; Thorn, Simon; Müller, Jörg

2017-06-01

The habitat-amount hypothesis challenges traditional concepts that explain species richness within habitats, such as the habitat-patch hypothesis, where species number is a function of patch size and patch isolation. It posits that effects of patch size and patch isolation are driven by effects of sample area, and thus that the number of species at a site is basically a function of the total habitat amount surrounding this site. We tested the habitat-amount hypothesis for saproxylic beetles and their habitat of dead wood by using an experiment comprising 190 plots with manipulated patch sizes situated in a forested region with a high variation in habitat amount (i.e., density of dead trees in the surrounding landscape). Although dead wood is a spatio-temporally dynamic habitat, saproxylic insects have life cycles shorter than the time needed for habitat turnover and they closely track their resource. Patch size was manipulated by adding various amounts of downed dead wood to the plots (~800 m³ in total); dead trees in the surrounding landscape (~240 km 2 ) were identified using airborne laser scanning (light detection and ranging). Over 3 yr, 477 saproxylic species (101,416 individuals) were recorded. Considering 20-1,000 m radii around the patches, local landscapes were identified as having a radius of 40-120 m. Both patch size and habitat amount in the local landscapes independently affected species numbers without a significant interaction effect, hence refuting the island effect. Species accumulation curves relative to cumulative patch size were not consistent with either the habitat-patch hypothesis or the habitat-amount hypothesis: several small dead-wood patches held more species than a single large patch with an amount of dead wood equal to the sum of that of the small patches. Our results indicate that conservation of saproxylic beetles in forested regions should primarily focus on increasing the overall amount of dead wood without considering its spatial arrangement. This means dead wood should be added wherever possible including in local landscapes with low or high dead-wood amounts. For species that have disappeared from most forests owing to anthropogenic habitat degradation, this should, however, be complemented by specific conservation measures pursued within their extant distributional ranges. © 2017 by the Ecological Society of America.

Discordance between living and death assemblages as evidence for anthropogenic ecological change

PubMed Central

Kidwell, Susan M.

2007-01-01

Mismatches between the composition of a time-averaged death assemblage (dead remains sieved from the upper mixed-zone of the sedimentary column) and the local living community are typically attributed to natural postmortem processes. However, statistical analysis of 73 molluscan data sets from estuaries and lagoons reveals significantly poorer average “live-dead agreement” in settings of documented anthropogenic eutrophication (AE) than in areas where AE and other human impacts are negligible. Taxonomic similarity of paired live and dead species lists declines steadily among areas as a function of AE severity, and, for data sets comprising only adults, rank-order agreement in species abundance drops where AE is suspected. The observed live-dead differences in composition are consistent with eutrophication (anomalous abundance of seagrass-dwellers and/or scarcity of organic-loving species in the death assemblage), suggesting compositional inertia of death assemblages to recent environmental change. Molluscan data sets from open shelf settings (n = 34) also show higher average live-dead discordance in areas of AE. These results indicate that (i) live-dead discordance in surficial grab samples provides valuable evidence for strong anthropogenic modification of benthic communities, (ii) actualistic estimates of the ecological fidelity of molluscan death assemblages tend to be erroneously pessimistic when conducted in nonpristine settings, and (iii) based on their high fidelity in pristine study areas, death assemblages are a promising means of reconstructing otherwise elusive preimpact ecological baselines from sedimentary records. PMID:17965231

Crucial parameter of the outcome in Crimean Congo hemorrhagic fever: Viral load.

PubMed

Hasanoglu, Imran; Guner, Rahmet; Carhan, Ahmet; Kocak Tufan, Zeliha; Yagci-Caglayik, Dilek; Guven, Tumer; Yilmaz, Gul Ruhsar; Tasyaran, Mehmet A

2016-02-01

Crimean Congo hemorrhagic fever (CCHF) is a fatal disease with a mortality rate of 5-30%. CCHF can be asymptomatic or it may progress with bleeding and cause mortality. To evaluate relation of viral load with mortality, clinical and laboratory findings in CCHF. A total of 126 CCHF patients were included. Serum samples obtained from all patients on admission for measurement of viral load. In our study, mortality rate was 11.1%. The most important prognostic factor was viral load. Mean viral load was 8.3×10(7)copy/ml and 4.6×10(9)copy/ml in survived and dead patients, respectively (p<0.005). Probability of survival is found to be significantly reduced where AST >1130U/l, ALT >490U/l, CPK >505U/l, LDH >980U/l, platelet count <23×10(3)/l, creatinine >1.4mg/dl, INR >1.3, d-dimer >7100ng/dl, and viral load >1.03×10(8)copy/ml. Patients with 10(8)copy/ml or higher viral load had diarrhea, headache, unconsciousness, bleeding, and seizure significantly more frequently (p<0.05). WBC, hemoglobin, platelet counts were significantly lower whereas AST, ALT, CPK, LDH, creatinine levels, PT and aPTT time, d-dimer levels, and INR were found to be significantly higher in these group. There are several severity criteria for prognosis of CCHF. In addition to these parameters, we introduce creatinine as a predictive factor for prognosis. Our study, which has the largest number of patients among studies that evaluate viral load on CCHF shows that viral load is the most effective parameter on mortality. Copyright © 2015 Elsevier B.V. All rights reserved.

Planting of neonicotinoid-coated corn raises honey bee mortality and sets back colony development.

PubMed

Samson-Robert, Olivier; Labrie, Geneviève; Chagnon, Madeleine; Fournier, Valérie

2017-01-01

Worldwide occurrences of honey bee colony losses have raised concerns about bee health and the sustainability of pollination-dependent crops. While multiple causal factors have been identified, seed coating with insecticides of the neonicotinoid family has been the focus of much discussion and research. Nonetheless, few studies have investigated the impacts of these insecticides under field conditions or in commercial beekeeping operations. Given that corn-seed coating constitutes the largest single use of neonicotinoid, our study compared honey bee mortality from commercial apiaries located in two different agricultural settings, i.e. corn-dominated areas and corn-free environments, during the corn planting season. Data was collected in 2012 and 2013 from 26 bee yards. Dead honey bees from five hives in each apiary were counted and collected, and samples were analyzed using a multi-residue LC-MS/MS method. Long-term effects on colony development were simulated based on a honey bee population dynamic model. Mortality survey showed that colonies located in a corn-dominated area had daily mortality counts 3.51 times those of colonies from corn crop-free sites. Chemical analyses revealed that honey bees were exposed to various agricultural pesticides during the corn planting season, but were primarily subjected to neonicotinoid compounds (54% of analysed samples contained clothianidin, and 31% contained both clothianidin and thiamethoxam). Performance development simulations performed on hive populations' show that increased mortality during the corn planting season sets back colony development and bears contributions to collapse risk but, most of all, reduces the effectiveness and value of colonies for pollination services. Our results also have implications for the numerous large-scale and worldwide-cultivated crops that currently rely on pre-emptive use of neonicotinoid seed treatments.

Response of breeding birds to aerial sprays of trichlorfon (Dylox) and carbaryl (Sevin-4-Oil) in Montana forests

USGS Publications Warehouse

DeWeese, L.R.; Henny, C.J.; Floyd, R.L.; Bobal, K.A.; Schultz, A.W.

1979-01-01

Breeding density, food, nesting success, and mortality of 20 bird species were monitored at Beaverhead National Forest, Montana, in 1975 in conjunction with experimental applications of trichlorfon (Dylox) and carbaryl (Sevin-4-oil) to western budworms (Choristoneura occidentalis). Bird species on nine 350- to 550-ha forested plots (three controls and three treated with each pesticide) were studied before and for 14 days after the spraying of trichlorfon at 1.1 kg in?9.4 L of Panasol AN3 per ha (1 pound active ingredient in 1.0 gallon/acre) and of carbaryl at 1.1 kg in 4.7 L of diesel oil per ha (l pound active ingredient in 0.5 gallon/acre). No significant decrease in bird numbers was detected from breeding-pair estimates or live bird counts after the spraying. Of the breeding pairs present before spraying, 92% remained on control plots, 89% on trichlorfon plots, and 92% on carbaryl plots. Counts of live birds made before and after spraying in three types of habitat supported the. results of the breeding-pair estimates. Nests with eggs or with young at the time of spraying were 74 and 97% successful, respectively, in control plots, 83 and 100% in plots sprayed with trichlorfon, and 86 and 100% in plots sprayed with carbaryl. No sick or dead birds were found after the spraying, although budworms were found in bird stomachs, and tracer-dye from the pesticide occurred on the feathers or feet of 74% of the 202 birds collected. Species dwelling in the tree canopy encountered the dye (and thus the pesticide) at a slightly higher rate (80%) than did species below the treetops (71 %) or near the ground and in open areas (70%).

Development of a quantitative PCR for detection of Lactobacillus plantarum starters during wine malolactic fermentation.

PubMed

Cho, Gyu-Sung; Krauss, Sabrina; Huch, Melanie; Du Toit, Maret; Franz, Charles M A P

2011-12-01

A quantitative, real-time PCR method was developed to enumerate Lactobacillus plantarum IWBT B 188 during the malolactic fermentation (MLF) in Grauburgunder wine. The qRT-PCR was strain-specific, as it was based on primers targeting a plasmid DNA sequence, or it was L. plantarum-specific, as it targeted a chromosomally located plantaricin gene sequence. Two 50 l wine fermentations were prepared. One was inoculated with 15 g/hl Saccharomyces cerevisiae, followed by L. plantarum IWBT B 188 at 3.6 × 10(6) CFU/ml, whereas the other was not inoculated (control). Viable cell counts were performed for up to 25 days on MRS agar, and the same cells were enumerated by qRT-PCR with both the plasmid or chromosomally encoded gene primers. The L. plantarum strain survived under the harsh conditions in the wine fermentation at levels above 10(5)/ml for approx. 10 days, after which cell numbers decreased to levels of 10(3) CFU/ml at day 25, and to below the detection limit after day 25. In the control, no lactic acid bacteria could be detected throughout the fermentation, with the exception of two sampling points where ca. 1 × 10(2) CFU/ml was detected. The minimum detection level for quantitative PCR in this study was 1 × 10(2) to 1 × 10(3) CFU/ml. The qRT-PCR results determined generally overestimated the plate count results by about 1 log unit, probably as a result of the presence of DNA from dead cells. Overall, qRT-PCR appeared to be well suited for specifically enumerating Lactobacillus plantarum starter cultures in the MLF in wine.

Planting of neonicotinoid-coated corn raises honey bee mortality and sets back colony development

PubMed Central

Samson-Robert, Olivier; Labrie, Geneviève; Chagnon, Madeleine

2017-01-01

Worldwide occurrences of honey bee colony losses have raised concerns about bee health and the sustainability of pollination-dependent crops. While multiple causal factors have been identified, seed coating with insecticides of the neonicotinoid family has been the focus of much discussion and research. Nonetheless, few studies have investigated the impacts of these insecticides under field conditions or in commercial beekeeping operations. Given that corn-seed coating constitutes the largest single use of neonicotinoid, our study compared honey bee mortality from commercial apiaries located in two different agricultural settings, i.e. corn-dominated areas and corn-free environments, during the corn planting season. Data was collected in 2012 and 2013 from 26 bee yards. Dead honey bees from five hives in each apiary were counted and collected, and samples were analyzed using a multi-residue LC-MS/MS method. Long-term effects on colony development were simulated based on a honey bee population dynamic model. Mortality survey showed that colonies located in a corn-dominated area had daily mortality counts 3.51 times those of colonies from corn crop-free sites. Chemical analyses revealed that honey bees were exposed to various agricultural pesticides during the corn planting season, but were primarily subjected to neonicotinoid compounds (54% of analysed samples contained clothianidin, and 31% contained both clothianidin and thiamethoxam). Performance development simulations performed on hive populations’ show that increased mortality during the corn planting season sets back colony development and bears contributions to collapse risk but, most of all, reduces the effectiveness and value of colonies for pollination services. Our results also have implications for the numerous large-scale and worldwide-cultivated crops that currently rely on pre-emptive use of neonicotinoid seed treatments. PMID:28828265

5000 yr of paleoseismicity along the southern Dead Sea fault

NASA Astrophysics Data System (ADS)

Klinger, Y.; Le Béon, M.; Al-Qaryouti, M.

2015-07-01

The 1000-km-long left-lateral Dead Sea fault is a major tectonic structure of the oriental Mediterranean basin, bounding the Arabian Plate to the west. The fault is located in a region with an exceptionally long and rich historical record, allowing to document historical seismicity catalogues with unprecedented level of details. However, if the earthquake time series is well documented, location and lateral extent of past earthquakes remain often difficult to establish, if only based on historical testimonies. We excavated a palaeoseismic trench in a site located in a kilometre-size extensional jog, south of the Dead Sea, in the Wadi Araba. Based on the stratigraphy exposed in the trench, we present evidence for nine earthquakes that produced surface ruptures during a time period spanning 5000 yr. Abundance of datable material allows us to tie the five most recent events to historical earthquakes with little ambiguities, and to constrain the possible location of these historical earthquakes. The events identified at our site are the 1458 C.E., 1212 C.E., 1068 C.E., one event during the 8th century crisis, and the 363 C.E. earthquake. Four other events are also identified, which correlation with historical events remains more speculative. The magnitude of earthquakes is difficult to assess based on evidence at one site only. The deformation observed in the excavation, however, allows discriminating between two classes of events that produced vertical deformation with one order of amplitude difference, suggesting that we could distinguish earthquakes that started/stopped at our site from earthquakes that potentially ruptured most of the Wadi Araba fault. The time distribution of earthquakes during the past 5000 yr is uneven. The early period shows little activity with return interval of ˜500 yr or longer. It is followed by a ˜1500-yr-long period with more frequent events, about every 200 yr. Then, for the past ˜550 yr, the fault has switched back to a quieter mode with no significant earthquake along the entire southern part of the Dead Sea fault, between the Dead Sea and the Gulf of Aqaba. We computed the Coefficient of Variation for our site and three other sites along the Dead Sea fault, south of Lebanon, to compare time distribution of earthquakes at different locations along the fault. With one exception at a site located next to Lake Tiberias, the three other sites are consistent to show some temporal clustering at the scale of few thousands years.

The Immune Interaction between HIV-1 Infection and Mycobacterium tuberculosis.

PubMed

Du Bruyn, Elsa; Wilkinson, Robert John

2016-12-01

The modulation of tuberculosis (TB)-induced immunopathology caused by human immunodeficiency virus (HIV)-1 coinfection remains incompletely understood but underlies the change seen in the natural history, presentation, and prognosis of TB in such patients. The deleterious combination of these two pathogens has been dubbed a "deadly syndemic," with each favoring the replication of the other and thereby contributing to accelerated disease morbidity and mortality. HIV-1 is the best-recognized risk factor for the development of active TB and accounts for 13% of cases globally. The advent of combination antiretroviral therapy (ART) has considerably mitigated this risk. Rapid roll-out of ART globally and the recent recommendation by the World Health Organization (WHO) to initiate ART for everyone living with HIV at any CD4 cell count should lead to further reductions in HIV-1-associated TB incidence because susceptibility to TB is inversely proportional to CD4 count. However, it is important to note that even after successful ART, patients with HIV-1 are still at increased risk for TB. Indeed, in settings of high TB incidence, the occurrence of TB often remains the first presentation of, and thereby the entry into, HIV care. As advantageous as ART-induced immune recovery is, it may also give rise to immunopathology, especially in the lower-CD4-count strata in the form of the immune reconstitution inflammatory syndrome. TB-immune reconstitution inflammatory syndrome will continue to impact the HIV-TB syndemic.

Active cancellation - A means to zero dead-time pulse EPR.

PubMed

Franck, John M; Barnes, Ryan P; Keller, Timothy J; Kaufmann, Thomas; Han, Songi

2015-12-01

The necessary resonator employed in pulse electron paramagnetic resonance (EPR) rings after the excitation pulse and creates a finite detector dead-time that ultimately prevents the detection of signal from fast relaxing spin systems, hindering the application of pulse EPR to room temperature measurements of interesting chemical or biological systems. We employ a recently available high bandwidth arbitrary waveform generator (AWG) to produce a cancellation pulse that precisely destructively interferes with the resonant cavity ring-down. We find that we can faithfully detect EPR signal at all times immediately after, as well as during, the excitation pulse. This is a proof of concept study showcasing the capability of AWG pulses to precisely cancel out the resonator ring-down, and allow for the detection of EPR signal during the pulse itself, as well as the dead-time of the resonator. However, the applicability of this approach to conventional EPR experiments is not immediate, as it hinges on either (1) the availability of low-noise microwave sources and amplifiers to produce the necessary power for pulse EPR experiment or (2) the availability of very high conversion factor micro coil resonators that allow for pulse EPR experiments at modest microwave power. Copyright © 2015 Elsevier Inc. All rights reserved.

Options for reducing HIV transmission related to the dead space in needles and syringes.

PubMed

Zule, William A; Pande, Poonam G; Otiashvili, David; Bobashev, Georgiy V; Friedman, Samuel R; Gyarmathy, V Anna; Des Jarlais, Don C

2018-01-15

When shared by people who inject drugs, needles and syringes with different dead space may affect the probability of HIV and hepatitis C virus (HCV) transmission differently. We measured dead space in 56 needle and syringe combinations obtained from needle and syringe programs across 17 countries in Europe and Asia. We also calculated the amounts of blood and HIV that would remain in different combinations following injection and rinsing. Syringe barrel capacities ranged from 0.5 to 20 mL. Needles ranged in length from 8 to 38 mm. The average dead space was 3 μL in low dead space syringes with permanently attached needles, 13 μL in high dead space syringes with low dead space needles, 45 μL in low dead space syringes with high dead space needles, and 99 μL in high dead space syringes with high dead space needles. Among low dead space designs, calculated volumes of blood and HIV viral burden were lowest for low dead space syringes with permanently attached needles and highest for low dead space syringes with high dead space needles. The dead space in different low dead space needle and syringe combinations varied substantially. To reduce HIV transmission related to syringe sharing, needle and syringe programs need to combine this knowledge with the needs of their clients.

[Studies on antimicrobial concentrations of flomoxef in serum, pelvic dead space exudate, and pelvic organs/tissues].

PubMed

Obata, T; Koishi, K; Sasaki, J; Eguchi, M; Yamamoto, Y

1987-10-01

To women undergoing radical and total hysterectomy, flomoxef (FMOX, 6315-S) in a dose of 2 g was administered by intravenous drip infusion over 1 hour and drug concentrations in serum and pelvic dead space exudate as well as pelvic organs/tissues were determined over time. The following results were obtained: 1. Serum concentrations of FMOX after intravenous infusion showed the peak value of 92.86 +/- 17.05 micrograms/ml at the end of infusion and then gradually decreased to 29.00 +/- 10.49 micrograms/ml in 1 hour and 1.16 +/- 1.08 micrograms/ml in 6 hours. 2. Concentrations in pelvic dead space exudate, which were 6.54 +/- 3.21 micrograms/ml at the end of intravenous infusion, gradually increased to 31.28 +/- 12.69 micrograms/ml in 30 minutes, and the peak of 35.21 +/- 13.29 micrograms/ml in 1 hour. Exudate concentrations gradually decreased to 11.10 +/- 6.64 micrograms/ml at 6 hours after infusion. 3. The serum concentration at the ligature of uterine artery was 103.21 +/- 51.69 micrograms/ml. Among concentrations in pelvic organ/tissues 37.17 +/- 18.20 micrograms/ml in uterine cervix was the highest, followed by 35.77 +/- 7.68 micrograms/g in portio vaginalis, 26.35 +/- 14.15 micrograms/g in tube, 21.62 +/- 12.15 micrograms/g in ovary, 20.56 +/- 9.82 micrograms/g in myometrium, and 16.45 +/- 8.10 micrograms/g in endometrium, in this order. 4. From an analysis of the two-compartment model, the maximum serum concentration was 92.81 micrograms/ml, which was very high. The time of 50% reduction of concentration in beta phase was 1.21 hours. In the pelvic dead space exudate, the maximum concentration was 32.38 micrograms/ml and the time of 50% reduction was 2.44 hours. The AUC was 147 micrograms.hr/ml in serum and 201 micrograms.hr/ml in the pelvic dead space. The shift to the pelvic dead space was 137% when AUC's were used as the basis of the comparison. 5. Clinically, FMOX was excellently effective against adnexitis caused by Peptostreptococcus asaccharolyticus, intrauterine infection caused by Staphylococcus aureus, cystitis caused by Klebsiella and Escherichia coli, vaginal stump infection caused by Streptococcus and E. coli and many other infections.

Environmental contaminant studies by the Patuxent Wildlife Research Center

USGS Publications Warehouse

Heinz, G.H.; Hill, E.F.; Stickel, W.H.; Stickel, L.F.; Kenaga, E.E.

1979-01-01

Evaluation of the effects of environmental contaminants on wildlife is geared to interpreting events in the field, especially population effects, and both field and laboratory studies are planned for this purpose; procedures are adapted to specific problems and therefore do not include strict protocols or routine testing. Field evaluations include measurements of cholinesterase inhibition in brain or blood, search for dead or disabled animals, study of nesting success of birds, and general ecological observations. Residue analyses are used in evaluating organochlorine chemicals; samples may include whole bodies for determining level of exposure, brains for mortality diagnosis, whole blood for certain special studies, and eggs to help in evaluation of possible reproductive effects. Bird counts, singing-male census counts, small mammal trapping, and cage-in-field tests have proven to be ineffective or misleading and are not considered suitable for field evaluations under most circumstances. Usefulness of simulated field trials is limited to very special situations. Experimental studies that help predict and interpret field effects include determinations of lethal diagnostic levels, comparative lethal dietary toxicity tests, tests of secondary poisoning, measurement of residue loss rates, measurement of blood enzymes, tests of behavioral effects, and studies of reproductive effects.

Study on spoilage capability and VBNC state formation and recovery of Lactobacillus plantarum.

PubMed

Liu, Junyan; Li, Lin; Li, Bing; Peters, Brian M; Deng, Yang; Xu, Zhenbo; Shirtliff, Mark E

2017-09-01

The present study aimed at investigating the capability of L. plantarum strain BM-LP14723 to enter into and recover from the viable but nonculturable (VBNC) state and to cause beer spoilage. VBNC state was induced by incubating in beer with subculturing or low temperature treatment. Culturable, total, and viable cells numbers were assessed by MRS agar plate counting, acridine orange direct counting, and Live/Dead BacLight bacterial viability kit, respectively. Organic acids concentrations were measured by reversed-phase high performance liquid chromatography. VBNC L. plantarum cells were detected after 189 ± 1.9 days low temperature treatment or 29 ± 0.7 subcultures in beer. The VBNC L. plantarum retained spoilage capability. Addition of catalase is an effective method for the recovery of the VBNC L. plantarum cells. L. plantarum strain BM-LP14723 is capable of entering into and recovery from the VBNC state and maintained spoilage capability. The current study presented that beer-spoilage L. plantarum can hide both in breweries and during transporting and marketing process and thus lead to beer-spoilage incidents. Copyright © 2017 Elsevier Ltd. All rights reserved.

Label-Free, Flow-Imaging Methods for Determination of Cell Concentration and Viability.

PubMed

Sediq, A S; Klem, R; Nejadnik, M R; Meij, P; Jiskoot, Wim

2018-05-30

To investigate the potential of two flow imaging microscopy (FIM) techniques (Micro-Flow Imaging (MFI) and FlowCAM) to determine total cell concentration and cell viability. B-lineage acute lymphoblastic leukemia (B-ALL) cells of 2 different donors were exposed to ambient conditions. Samples were taken at different days and measured with MFI, FlowCAM, hemocytometry and automated cell counting. Dead and live cells from a fresh B-ALL cell suspension were fractionated by flow cytometry in order to derive software filters based on morphological parameters of separate cell populations with MFI and FlowCAM. The filter sets were used to assess cell viability in the measured samples. All techniques gave fairly similar cell concentration values over the whole incubation period. MFI showed to be superior with respect to precision, whereas FlowCAM provided particle images with a higher resolution. Moreover, both FIM methods were able to provide similar results for cell viability as the conventional methods (hemocytometry and automated cell counting). FIM-based methods may be advantageous over conventional cell methods for determining total cell concentration and cell viability, as FIM measures much larger sample volumes, does not require labeling, is less laborious and provides images of individual cells.

Design of fast signal processing readout front-end electronics implemented in CMOS 40 nm technology

NASA Astrophysics Data System (ADS)

Kleczek, Rafal

2016-12-01

The author presents considerations on the design of fast readout front-end electronics implemented in a CMOS 40 nm technology with an emphasis on the system dead time, noise performance and power dissipation. The designed processing channel consists of a charge sensitive amplifier with different feedback types (Krummenacher, resistive and constant current blocks), a threshold setting block, a discriminator and a counter with logic circuitry. The results of schematic and post-layout simulations with randomly generated input pulses in a time domain according to the Poisson distribution are presented and analyzed. Dead time below 20 ns is possible while keeping noise ENC ≈ 90 e- for a detector capacitance CDET = 160 fF.

Compact pulse width modulation circuitry for silicon photomultiplier readout.

PubMed

Bieniosek, M F; Olcott, P D; Levin, C S

2013-08-07

The adoption of solid-state photodetectors for positron emission tomography (PET) system design and the interest in 3D interaction information from PET detectors has lead to an increasing number of readout channels in PET systems. To handle these additional readout channels, PET readout electronics should be simplified to reduce the power consumption, cost, and size of the electronics for a single channel. Pulse-width modulation (PWM), where detector pulses are converted to digital pulses with width proportional to the detected photon energy, promises to simplify PET readout by converting the signals to digital form at the beginning of the processing chain, and allowing a single time-to-digital converter to perform the data acquisition for many channels rather than routing many analogue channels and digitizing in the back end. Integrator based PWM systems, also known as charge-to-time converters (QTCs), are especially compact, reducing the front-end electronics to an op-amp integrator with a resistor discharge, and a comparator. QTCs, however, have a long dead-time during which dark count noise is integrated, reducing the output signal-to-noise ratio. This work presents a QTC based PWM circuit with a gated integrator that shows performance improvements over existing QTC based PWM. By opening and closing an analogue switch on the input of the integrator, the circuit can be controlled to integrate only the portions of the signal with a high signal-to-noise ratio. It also allows for multiplexing different detectors into the same PWM circuit while avoiding uncorrelated noise propagation between photodetector channels. Four gated integrator PWM circuits were built to readout the spatial channels of two position sensitive solid-state photomultiplier (PS-SSPM). Results show a 4 × 4 array 0.9 mm × 0.9 mm × 15 mm of LYSO crystals being identified on the 5 mm × 5 mm PS-SSPM at room temperature with no degradation for twofold multiplexing. In principle, much larger multiplexing ratios are possible, limited only by count rate issues.

Brought in Dead: An Avoidable Delay in Maternal Deaths.

PubMed

Kumar, Aruna; Agrawal, Neha

2016-10-01

Maternal brought in dead are the patient who dies in the need of adequate medical care. These deaths are often not analyzed sincerely as they are not institutional deaths. Our aim is to find out actual life threatening cause of delay leading to death. Patients brought dead to casualty were seen by the doctors on duty in Department of Obstetrics and Gynaecology,Gandhi Medical College, Bhopal round the clock. Cause of death was analyzed by verbal autopsy of attendants and referral letter from the institute. In this analytical study a complete evaluation of brought deaths from January 2011 to Decmeber 2014 was done. A total of 64 brought in deaths were reported in this 4 year duration. Most common cause of death was postpartum hemorrhage (54.68 %) followed by hypertension (15.62 %) and the most common cause of delay was delay in getting adequate treatment (56.25 %). The brought in dead are the indicator of the three delays in getting health care. Challenges appear to be enormous to be tackled. Timely management proves to be critical in preventing maternal death. Thus it appears that community education about pregnancy and its complications, EmOC training at FRU and strict adherence to referral protocol may help us to reduce the brought dead burden.

Changes of mercury contamination in red-crowned cranes, Grus japonensis, in East Hokkaido, Japan.

PubMed

Teraoka, Hiroki; Tagami, Yukari; Kudo, Moe; Miura, Yoshiaki; Okamoto, Erika; Matsumoto, Fumio; Koga, Kimiya; Uebayashi, Akiko; Shimura, Ryoji; Inoue, Masako; Momose, Kunikazu; Masatomi, Hiroyuki; Kitazawa, Takio; Hiraga, Takeo; Subramanian, Annamalai

2012-07-01

Red-crowned cranes (Grus japonensis) are native to eastern Hokkaido (island population), in contrast to the mainland, which migrates between the Amur River basin and eastern China-Korea peninsula. During the 1990s we found that Red-crowned cranes in Hokkaido were highly contaminated with mercury: however, the source was unknown. We investigated the time trend of mercury contamination in Red-crowned cranes. Total mercury levels in the livers and kidneys from cranes dead in the 2000s were lower than those dead in the 1990s. Feather is a major pathway of mercury excretion for many bird species and is used as an indicator of blood mercury level during feather growth. As internal organs from the specimens collected before 1988 were not available, we analyzed the flight feather shavings from stuffed Red-crowned cranes dead in 1959-1987 and found that the mercury level of feathers from cranes dead in the 1960s and 1970s was not more than those from the cranes dead in the 2000s. These results suggest that mercury contamination in Red-crowned cranes in Hokkaido decreased temporally during the 1990s-2000s. This indicates the possible occurrence of some mercury pollution in Red-crowned cranes' habitat in this region in the 1990s or before.

Self-accelerated development of salt karst during flash floods along the Dead Sea Coast, Israel

NASA Astrophysics Data System (ADS)

Avni, Yoav; Lensky, Nadav; Dente, Elad; Shviro, Maayan; Arav, Reuma; Gavrieli, Ittai; Yechieli, Yoseph; Abelson, Meir; Lutzky, Hallel; Filin, Sagi; Haviv, Itai; Baer, Gidon

2016-01-01

We document and analyze the rapid development of a real-time karst system within the subsurface salt layers of the Ze'elim Fan, Dead Sea, Israel by a multidisciplinary study that combines interferometric synthetic aperture radar and light detection and ranging measurements, sinkhole mapping, time-lapse camera monitoring, groundwater level measurements and chemical and isotopic analyses of surface runoff and groundwater. The >1 m/yr drop of Dead Sea water level and the subsequent change in the adjacent groundwater system since the 1960s resulted in flushing of the coastal aquifer by fresh groundwater, subsurface salt dissolution, gradual land subsidence and formation of sinkholes. Since 2010 this process accelerated dramatically as flash floods at the Ze'elim Fan were drained by newly formed sinkholes. During and immediately after these flood events the dissolution rates of the subsurface salt layer increased dramatically, the overlying ground surface subsided, a large number of sinkholes developed over short time periods (hours to days), and salt-saturated water resurged downstream. Groundwater flow velocities increased by more than 2 orders of magnitudes compared to previously measured velocities along the Dead Sea. The process is self-accelerating as salt dissolution enhances subsidence and sinkhole formation, which in turn increase the ponding areas of flood water and generate additional draining conduits to the subsurface. The rapid terrain response is predominantly due to the highly soluble salt. It is enhanced by the shallow depth of the salt layer, the low competence of the newly exposed unconsolidated overburden and the moderate topographic gradients of the Ze'elim Fan.

Increased dead space in face mask continuous positive airway pressure in neonates.

PubMed

Hishikawa, Kenji; Fujinaga, Hideshi; Ito, Yushi

2017-01-01

Continuous positive airway pressure (CPAP) by face mask is commonly performed in newborn resuscitation. We evaluated the effect of face mask CPAP on system dead space. Face mask CPAP increases dead space. A CPAP model study. We estimated the volume of the inner space of the mask. We devised a face mask CPAP model, in which the outlet of the mask was covered with plastic; and three modified face mask CPAP models, in which holes were drilled near to the cushion of the covered face mask to alter the air exit. We passed a continuous flow of 21% oxygen through each model and we controlled the inner pressure to 5 cmH 2 O by adjusting the flow-relief valve. To evaluate the ventilation in the inner space of each model, we measured the oxygen concentration rise time, that is, the time needed for the oxygen concentration of each model to reach 35% after the oxygen concentration of the continuous flow was raised from 21% to 40%. The volume of inner space of the face mask was 38.3 ml. Oxygen concentration rise time in the face mask CPAP model was significantly longer at various continuous flow rates and points of the inner space of the face mask compared with that of the modified face mask CPAP model. Our study indicates that face mask CPAP leads to an increase in dead space and a decrease in ventilation efficiency under certain circumstances. Pediatr Pulmonol. 2017;52:107-111. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Erratum to “Estimating the effective system dead time parameter for correlated neutron counting” [Nucl. Instrum. Methods Phys. Res. A 871 (2017) 154–160

DOE PAGES

Croft, S.; Cleveland, S.; Favalli, A.; ...

2018-02-23

The expressions given for φ, the ratio of effective system dead time to gate width, are wrong for the case of the third and fourth order forms because the simple square root is used when the 3rd and 4th roots, respectively, are required. We failed to notice during proof reading that this change from the submitted manuscript had crept in. The correct form should, however, be clear from the steps of the derivations outlined in the text; and so we hope our mistake has not misled anyone.

Design and Test of a 65nm CMOS Front-End with Zero Dead Time for Next Generation Pixel Detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaioni, L.; Braga, D.; Christian, D.

This work is concerned with the experimental characterization of a synchronous analog processor with zero dead time developed in a 65 nm CMOS technology, conceived for pixel detectors at the HL-LHC experiment upgrades. It includes a low noise, fast charge sensitive amplifier with detector leakage compensation circuit, and a compact, single ended comparator able to correctly process hits belonging to two consecutive bunch crossing periods. A 2-bit Flash ADC is exploited for digital conversion immediately after the preamplifier. A description of the circuits integrated in the front-end processor and the initial characterization results are provided

Erratum to “Estimating the effective system dead time parameter for correlated neutron counting” [Nucl. Instrum. Methods Phys. Res. A 871 (2017) 154–160

DOE Office of Scientific and Technical Information (OSTI.GOV)

Croft, S.; Cleveland, S.; Favalli, A.

The expressions given for φ, the ratio of effective system dead time to gate width, are wrong for the case of the third and fourth order forms because the simple square root is used when the 3rd and 4th roots, respectively, are required. We failed to notice during proof reading that this change from the submitted manuscript had crept in. The correct form should, however, be clear from the steps of the derivations outlined in the text; and so we hope our mistake has not misled anyone.

Moessbauer spectrometer based on UNO-4096-90 accumulator and Elektronika D3-28 microcomputer for simultaneous recording of four spectra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romanov, E.S.; Ivoilov, N.G.

A buffer memory unit and an interface for the UNO-4096-90 accumulator with an Elektronika D3-28 microcomputer are described that allow simultaneous recording of four Moessbauer spectra with zero dead time. For complete elimination of dead time, the pulses from each detector are fed to two buffer counters units, which operate alternately in the write and interrogate modes. This organization of the buffer memory also completely eliminates the effect of the sensors on one another. The use of these circuits does not require any modifications of the computer or accumulator.

The North Caucasus Insurgency: Dead or Alive

DTIC Science & Technology

2017-02-01

Shvedov, a liberal Rus- sian journalist and expert on the North Caucasus, stat- ed at the time that “the number of bombings , terrorist attacks and murders...crowded subway stations in Mos- cow were targeted by suicide bombers, resulting in 3 the deaths of 40 civilians. In January 2011, a bomb ex- ploded in...Moscow’s busy Domodedovo International Airport, leaving 37 dead. In 2013, three suicide bomb - ings on October 21, December 29, and December 30, shook

[Studies on the persistence of the infectivity of Trypanosoma cruzi. II. Persistence of infectivity of T. cruzi in dead bugs (author's transl)].

PubMed

Soares, V A; Marsden, P D

1979-12-01

Investigations into the viability time of T. cruzi in dead bugs experimentally infected with "Peru" strain showed a maximum of 9 days for Dipetalogaster maximus and 8 for Triatoma infestans maintained at ambient temperature (26 degrees C). On refrigeration survival was increased to 60 days. In routine xenodiagnosis in the refrigerator 90 day survival was noted of both T. cruzi and the vector bug.

The Slope Imaging Multi-polarization Photon-counting Lidar: an Advanced Technology Airborne Laser Altimeter

NASA Astrophysics Data System (ADS)

Dabney, P.; Harding, D. J.; Huss, T.; Valett, S.; Yu, A. W.; Zheng, Y.

2009-12-01

The Slope Imaging Multi-polarization Photon-counting Lidar (SIMPL) is an airborne laser altimeter developed through the NASA Earth Science Technology Office Instrument Incubator Program with a focus on cryopshere remote sensing. The SIMPL instrument incorporates a variety of advanced technologies in order to demonstrate measurement approaches of potential benefit for improved airborne laser swath mapping and spaceflight laser altimeter missions. SIMPL incorporates beam splitting, single-photon ranging and polarimetry technologies at green and near-infrared wavelengths in order to achieve simultaneous sampling of surface elevation, slope, roughness and scattering properties, the latter used to differentiate surface types. The transmitter is a 1 nsec pulse width, 11 kHz, 1064 nm microchip laser, frequency doubled to 532 nm and split into four plane-polarized beams using birefringent calcite crystal in order to maintain co-alignment of the two colors. The 16 channel receiver splits the received energy for each beam into the two colors and each color is split into energy parallel and perpendicular to the transmit polarization plane thereby proving a measure of backscatter depolarization. The depolarization ratio is sensitive to the proportions of specular reflection and surface and volume scattering, and is a function of wavelength. The ratio can differentiate, for example, water, young translucent ice, older granular ice and snow. The solar background count rate is controlled by spatial filtering using a pinhole array and by spectral filtering using temperature-controlled narrow bandwidth filters. The receiver is fiber coupled to 16 Single Photon Counting Modules (SPCMs). To avoid range biases due to the long dead time of these detectors the probability of detection per laser fire on each channel is controlled to be below 30%, using mechanical irises and flight altitude. Event timers with 0.1 nsec resolution in combination the narrow transmit pulse yields single photon ranging precision of 8 cm. The high speed, high throughput data system is capable of recording 22 million time-tagged photon detection events per second. At typical aircraft flight speeds, each of the 16 channels acquires a single photon range every 5 to 15 cm along the four profiles providing a highly sampled measure of surface roughness. The nominal flight altitude is 5 km yielding 10 m spacing between the four beam profiles, providing a measure of surface slope at 10 m length scales. The altitude is currently constrained by the low signal level of the NIR cross-polarized channels. SIMPL’s measurement capabilities provide information about surface elevation, roughness, slope and type of value in characterizing ice sheet surfaces and sea ice, including their melt state. Capabilities will be illustrated using data acquired over Lake Erie ice cover in February, 2009.

The Effects of the Mountain Pine Beetle on Snow Accumulation and Melt Timing in the Headwaters of the Colorado River

NASA Astrophysics Data System (ADS)

Pugh, E. T.; Small, E. E.

2010-12-01

The high-elevation forests that are a primary source for Colorado’s domestic and agricultural water needs are changing rapidly due to an infestation by the mountain pine beetle (MPB). MPB are native to Colorado’s high elevation forests. However, the frequency of MPB infestation and resulting tree death has increased dramatically over the past 15 years. In Colorado, over 8,000 km2 of Lodgepole (Pinus contorta) and Ponderosa Pine (Pinus ponderosa) forest have been infested by MPB since 1996. It is predicted that the current epidemic will kill most of the pines in these areas; MPB are very destructive to forest canopies, often killing all of the overhead trees within lodgepole pine stands. Current widespread MPB outbreaks are not limited to Colorado; they are also impacting forests in much of the Western US and British Columbia, Canada. This study is focused on quantifying the impacts of widespread tree death on Colorado’s mountain snowpack. The data were collected one to three years after beetle infestation, at various stages of tree mortality. During the winters of 2009 and 2010, snowpack and meteorological properties were measured at eight pairs of dead and living lodgepole pine stands. All stands are located at an elevation of 2720 ± 32m, in a subalpine region along the headwaters of the Colorado River. Trees in living stands were generally smaller in diameter and more densely populated than trees in dead stands. In the red phase of tree death, snowpack accumulated equally beneath living and dead tree stands. Additionally, snow under all tree stands became isothermal on the same date regardless of mortality. However, the snow was depleted as much as one week earlier beneath red phase dead stands. Canopy transmission of solar radiation was not consistently different between living and red phase dead stands. We noted more ground litter in red phase dead stands which would decrease snowpack albedo and lead to the snowmelt differences observed. We also performed an albedo experiment to quantify the impact of surface litter on snow albedo. Results are also reported for more advanced grey phase dead stands. Lastly, we present a conceptual model of how the primary snow processes change with time as tree mortality progresses through various stages and introduce future work.

Microbial nitrogen sinks in the water column of a large coastal hypoxic area, the Gulf of Mexico "Dead Zone"

NASA Astrophysics Data System (ADS)

Rogener, M. K.; Roberts, B. J.; Rabalais, N. N.; Stewart, F. J.; Joye, S. B.

2016-02-01

Excess nitrogen in coastal environments leads to eutrophication, harmful algal blooms, habitat loss, oxygen depletion and reductions in biodiversity. As such, biological nitrogen (N) removal through the microbially-mediated process of denitrification is a critical ecosystem function that can mitigate the negative consequences of excess nitrogen loading. However, denitrification can produce nitrous oxide, a potent greenhouse gas, as a byproduct under some environmental conditions. To understand how excess nitrogen loading impacts denitrification, we measured rates of this process in the water column of the Gulf of Mexico "Dead Zone" three times over the summer of 2015. The Dead Zone is generated by excessive nitrogen loading from the Mississippi River co-occurring with strong water column stratification, which leads to a large summer-time hypoxic/anoxic area at the mouth of the river and along the coast of Louisiana. Rates of denitrification ranged from 31 to 153 nmol L-1 d-1. Dead Zone waters are also enriched in methane and aerobic methane oxidation rates ranged from 0.1 to 4.3 nmol L-1 d-1. Maximal denitrification rates were observed at stations with the lowest oxygen concentrations and highest methane oxidation rates, suggesting a potential coupling between nitrate reduction and methane oxidation which both scrubs reactive N and methane from the system, thus performing a duel ecosystem service.

Integrated microfluidic technology for sub-lethal and behavioral marine ecotoxicity biotests

NASA Astrophysics Data System (ADS)

Huang, Yushi; Reyes Aldasoro, Constantino Carlos; Persoone, Guido; Wlodkowic, Donald

2015-06-01

Changes in behavioral traits exhibited by small aquatic invertebrates are increasingly postulated as ethically acceptable and more sensitive endpoints for detection of water-born ecotoxicity than conventional mortality assays. Despite importance of such behavioral biotests, their implementation is profoundly limited by the lack of appropriate biocompatible automation, integrated optoelectronic sensors, and the associated electronics and analysis algorithms. This work outlines development of a proof-of-concept miniaturized Lab-on-a-Chip (LOC) platform for rapid water toxicity tests based on changes in swimming patterns exhibited by Artemia franciscana (Artoxkit M™) nauplii. In contrast to conventionally performed end-point analysis based on counting numbers of dead/immobile specimens we performed a time-resolved video data analysis to dynamically assess impact of a reference toxicant on swimming pattern of A. franciscana. Our system design combined: (i) innovative microfluidic device keeping free swimming Artemia sp. nauplii under continuous microperfusion as a mean of toxin delivery; (ii) mechatronic interface for user-friendly fluidic actuation of the chip; and (iii) miniaturized video acquisition for movement analysis of test specimens. The system was capable of performing fully programmable time-lapse and video-microscopy of multiple samples for rapid ecotoxicity analysis. It enabled development of a user-friendly and inexpensive test protocol to dynamically detect sub-lethal behavioral end-points such as changes in speed of movement or distance traveled by each animal.

Solanaceae IV: Atropa belladonna, deadly nightshade.

PubMed

Lee, M R

2007-03-01

The Deadly Nightshade, Atropa belladonna, is a plant surrounded by myth, fear and awe. In antiquity, the Greeks and the Romans knew that it contained a deadly poison. In medieval times, it was widely used by witches, sorcerors and professional poisoners. Linnaeus later codified its remarkable properties as the genus Atropa, the Fate that slits the thin spun life and the species belladonna because of its power to dilate the pupils. In the 1830s, the pure alkaloid I-atropine was isolated from the plant. This proved to be a significant tool in the study of the autonomic nervous system leading to the identification of acetylcholine as an important neurotransmitter in mammals. When pure atropine became available, it caused a large number of deaths, whether by accident, suicide or homicide.

Measurement of temperature changes in cooling dead rats using magnetic resonance thermometry.

PubMed

Kuribayashi, Hideto; Cui, Fanlai; Hirakawa, Keiko; Kanawaku, Yoshimasa; Ohno, Youkichi

2011-11-01

Magnetic resonance imaging thermometry has been introduced as a technique for measurement of temperature changes in cooling dead rats. Rat pelvic magnetic resonance images were acquired sequentially more than 2h after euthanasia by halothane overdose. A series of temperature difference maps in cooling dead rats was obtained with calculating imaging phase changes induced by the water proton frequency shift caused by temperature changes. Different cooling processes were monitored by the temperature difference maps in the rats. Magnetic resonance imaging thermometry applied in the study of laboratory animals could theoretically reproduce a variety of causes of death with different environmental conditions. Outcomes from experimental animal studies could be translated into a temperature-based time of death estimation in forensics. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Microbial Characterization Space Solid Wastes Treated with a Heat Melt Compactor

NASA Technical Reports Server (NTRS)

Strayer, Richard F.; Hummerick, Mary E.; Richards, Jeffrey T.; McCoy LaShelle E.; Roberts, Michael S.; Wheeler, Raymond M.

2012-01-01

The on going purpose of the project efforts was to characterize and determine the fate of microorganisms in space-generated solid wastes before and after processing by candidate solid waste processing. For FY 11, the candidate technology that was assessed was the Heat Melt Compactor (HMC). The scope included five HMC. product disks produced at ARC from either simulated space-generated trash or from actual space trash, Volume F compartment wet waste, returned on STS 130. This project used conventional microbiological methods to detect and enumerate microorganisms in heat melt compaction (HMC) product disks as well as surface swab samples of the HMC hardware before and after operation. In addition, biological indicators were added to the STS trash prior to compaction in order to determine if these spore-forming bacteria could survive the HMC processing conditions, i.e., high temperature (160 C) over a long duration (3 hrs). To ensure that surface dwelling microbes did not contaminate HMC product disk interiors, the disk surfaces were sanitized with 70% alcohol. Microbiological assays were run before and after sanitization and found that sanitization greatly reduced the number of identified isolates but did not totally eliminate them. To characterize the interior of the disks, ten 1.25 cm diameter core samples were aseptically obtained for each disk. These were run through the microbial characterization analyses. Low counts of bacteria, on the order of 5 to 50 per core, were found, indicating that the HMC operating conditions might not be sufficient for waste sterilization. However, the direct counts were 6 to 8 orders of magnitude greater, indicating that the vast majority of microbes present in the wastes were dead or non-cultivable. An additional indication that the HMC was sterilizing the wastes was the results from the added commercial spore test strips to the wastes prior to HMC operation. Nearly all could be recovered from the HMC disks post-operation and all were showed negative growth when run through the manufacturer's protocol, meaning that the 106 or so spores impregnated into the strips were dead. Control test strips, i.e., not exposed to the HMC conditions were all strongly positive. One area of concern is that the identities of isolates from the cultivable counts included several human pathogens, namely Staphylococcus aureus. The project reported here provides microbial characterization support to the Waste Management Systems element of the Life Support and Habitation Systems program.

9 CFR 82.6 - Interstate movement of dead birds and dead poultry from a quarantined area.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Interstate movement of dead birds and... (END) § 82.6 Interstate movement of dead birds and dead poultry from a quarantined area. (a) Except as provided in paragraph (b) of this section for dressed carcasses, dead birds and dead poultry, including any...

9 CFR 82.6 - Interstate movement of dead birds and dead poultry from a quarantined area.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Interstate movement of dead birds and... (END) § 82.6 Interstate movement of dead birds and dead poultry from a quarantined area. (a) Except as provided in paragraph (b) of this section for dressed carcasses, dead birds and dead poultry, including any...

In vivo photoacoustic flow cytometry for early malaria diagnosis.

PubMed

Cai, Chengzhong; Carey, Kai A; Nedosekin, Dmitry A; Menyaev, Yulian A; Sarimollaoglu, Mustafa; Galanzha, Ekaterina I; Stumhofer, Jason S; Zharov, Vladimir P

2016-06-01

In vivo photoacoustic (PA) flow cytometry (PAFC) has already demonstrated a great potential for the diagnosis of deadly diseases through ultrasensitive detection of rare disease-associated circulating markers in whole blood volume. Here, we demonstrate the first application of this powerful technique for early diagnosis of malaria through label-free detection of malaria parasite-produced hemozoin in infected red blood cells (iRBCs) as high-contrast PA agent. The existing malaria tests using blood smears can detect the disease at 0.001-0.1% of parasitemia. On the contrary, linear PAFC showed a potential for noninvasive malaria diagnosis at an extremely low level of parasitemia of 0.0000001%, which is ∼10(3) times better than the existing tests. Multicolor time-of-flight PAFC with high-pulse repetition rate lasers at wavelengths of 532, 671, and 820 nm demonstrated rapid spectral and spatial identification and quantitative enumeration of individual iRBCs. Integration of PAFC with fluorescence flow cytometry (FFC) provided real-time simultaneous detection of single iRBCs and parasites expressing green fluorescence proteins, respectively. A combination of linear and nonlinear nanobubble-based multicolor PAFC showed capability to real-time control therapy efficiency by counting of iRBCs before, during, and after treatment. Our results suggest that high-sensitivity, high-resolution ultrafast PAFC-FFC platform represents a powerful research tool to provide the insight on malaria progression through dynamic study of parasite-cell interactions directly in bloodstream, whereas portable hand-worn PAFC device could be broadly used in humans for early malaria diagnosis. © 2016 International Society for Advancement of Cytometry. © 2016 International Society for Advancement of Cytometry.

Time Evolving Fission Chain Theory and Fast Neutron and Gamma-Ray Counting Distributions

DOE PAGES

Kim, K. S.; Nakae, L. F.; Prasad, M. K.; ...

2015-11-01

Here, we solve a simple theoretical model of time evolving fission chains due to Feynman that generalizes and asymptotically approaches the point model theory. The point model theory has been used to analyze thermal neutron counting data. This extension of the theory underlies fast counting data for both neutrons and gamma rays from metal systems. Fast neutron and gamma-ray counting is now possible using liquid scintillator arrays with nanosecond time resolution. For individual fission chains, the differential equations describing three correlated probability distributions are solved: the time-dependent internal neutron population, accumulation of fissions in time, and accumulation of leaked neutronsmore » in time. Explicit analytic formulas are given for correlated moments of the time evolving chain populations. The equations for random time gate fast neutron and gamma-ray counting distributions, due to randomly initiated chains, are presented. Correlated moment equations are given for both random time gate and triggered time gate counting. There are explicit formulas for all correlated moments are given up to triple order, for all combinations of correlated fast neutrons and gamma rays. The nonlinear differential equations for probabilities for time dependent fission chain populations have a remarkably simple Monte Carlo realization. A Monte Carlo code was developed for this theory and is shown to statistically realize the solutions to the fission chain theory probability distributions. Combined with random initiation of chains and detection of external quanta, the Monte Carlo code generates time tagged data for neutron and gamma-ray counting and from these data the counting distributions.« less

Diurnal Course of Evaporation From the Dead Sea in Summer: A Distinct Double Peak Induced by Solar Radiation and Night Sea Breeze

NASA Astrophysics Data System (ADS)

Lensky, N. G.; Lensky, I. M.; Peretz, A.; Gertman, I.; Tanny, J.; Assouline, S.

2018-01-01

Partitioning between the relative effects of the radiative and aerodynamic components of the atmospheric forcing on evaporation is challenging since diurnal distributions of wind speed and solar radiation typically overlap. The Dead Sea is located about a 100 km off the Eastern Mediterranean coast, where and the Mediterranean Sea breeze front reaches it after sunset. Therefore, in the Dead Sea the peaks of solar radiation and wind speed diurnal cycles in the Dead Sea are distinctly separated in time, offering a unique opportunity to distinguish between their relative impacts on evaporation. We present mid-summer eddy covariance and meteorological measurements of evaporation rate and surface energy fluxes over the Dead Sea. The evaporation rate is characterized by a clear diurnal cycle with a daytime peak, few hours after solar radiation peak, and a nighttime peak coincident with wind speed peak. Evaporation rate is minimum during sunrise and sunset. Measurements of evaporation rate from two other water bodies that are closer to the Mediterranean coast, Eshkol Reservoir, and Lake Kinneret, present a single afternoon peak, synchronous with the sea breeze. The inland diurnal evaporation rate cycle varies with the distance from the Mediterranean coast, following the propagation of sea breeze front: near the coast, wind speed, and radiation peaks are close and consequently a single daily evaporation peak appears in the afternoon; at the Dead Sea, about a 100 km inland, the sea breeze front arrives at sunset, resulting in a diurnal evaporation cycle characterized by a distinct double peak.

Somatic survival and organ donation among brain-dead patients in the state of Qatar.

PubMed

George, Saibu; Thomas, Merlin; Ibrahim, Wanis H; Abdussalam, Ahmed; Chandra, Prem; Ali, Husain Shabbir; Raza, Tasleem

2016-10-31

The Qatari law, as in many other countries, uses brain death as the main criteria for organ donation and cessation of medical support. By contrast, most of the public in Qatar do not agree with the limitation or withdrawal of medical care until the time of cardiac death. The current study aims to examine the duration of somatic survival after brain death, organ donation rate in brain-dead patients as well as review the underlying etiologies and level of support provided in the state of Qatar. This is a retrospective study of all patients diagnosed with brain death over a 10-year period conducted at the largest tertiary center in Qatar (Hamad General Hospital). Among the 53 patients who were diagnosed with brain death during the study period, the median and mean somatic survivals of brain-dead patients in the current study were 3 and 4.5 days respectively. The most common etiology was intracranial hemorrhage (45.3 %) followed by ischemic stroke (17 %). Ischemic stroke patients had a median survival of 11 days. Organ donation was accepted by only two families (6.6 %) of the 30 brain dead patients deemed suitable for organ donation. The average somatic survival of brain-dead patients is less than one week irrespective of supportive measures provided. Organ donation rate was extremely low among brain-dead patients in Qatar. Improved public education may lead to significant improvement in resource utilization as well as organ transplant donors and should be a major target area of future health care policies.

Water input requirements of the rapidly shrinking Dead Sea

NASA Astrophysics Data System (ADS)

Abu Ghazleh, Shahrazad; Hartmann, Jens; Jansen, Nils; Kempe, Stephan

2009-05-01

The deepest point on Earth, the Dead Sea level, has been dropping alarmingly since 1978 by 0.7 m/a on average due to the accelerating water consumption in the Jordan catchment and stood in 2008 at 420 m below sea level. In this study, a terrain model of the surface area and water volume of the Dead Sea was developed from the Shuttle Radar Topography Mission data using ArcGIS. The model shows that the lake shrinks on average by 4 km2/a in area and by 0.47 km3/a in volume, amounting to a cumulative loss of 14 km3 in the last 30 years. The receding level leaves almost annually erosional terraces, recorded here for the first time by Differential Global Positioning System field surveys. The terrace altitudes were correlated among the different profiles and dated to specific years of the lake level regression, illustrating the tight correlation between the morphology of the terrace sequence and the receding lake level. Our volume-level model described here and previous work on groundwater inflow suggest that the projected Dead Sea-Red Sea channel or the Mediterranean-Dead Sea channel must have a carrying capacity of >0.9 km3/a in order to slowly re-fill the lake to its former level and to create a sustainable system of electricity generation and freshwater production by desalinization. Moreover, such a channel will maintain tourism and potash industry on both sides of the Dead Sea and reduce the natural hazard caused by the recession.

Potential of Staphylococcus xylosus strain for recovering nickel ions from aqueous solutions

NASA Astrophysics Data System (ADS)

Al-Gheethi, A.; Efaq, A. N.; Mohamed, R. M.; Abdel-Monem, M.; Amir Hashim, M.

2017-10-01

The potential of bacterial biomass for the biosorption of heavy metals has investigated extensively. However, the bacterial species exhibited different affinities toward the heavy metals ions based on their differences in cell wall characteristics, structure and physiological status (living or dead cells). In this study, the potential of living and dead cells of Staphylococcus xylosus 222W for removal nickel ions from aqueous solution as a function for physiological status, nickel and biomass concentrations, time, pH and temperature was investigated. The pre-treatment of bacterial cells was performed by the heating at 100 °C for 15 min. The removal experiments were conducted in the lab scale. The results revealed that the dead cells exhibited more efficiency in removing nickel ions than living cells at all investigated concentrations (2 to 10 mM). The biosorption efficiency (E %) increased with increasing in biomass cells to limit concentrations (0.1 to 1 g dry wt L-1). The maximum removal of nickel was 81.41 vs. 77.10 % by living and dead cells, respectively achieved after 9 and 10 hrs of the incubation period, respectively. The acidic conditions decrease the efficiency of metal removal, while the optimal removal was recorded at pH 8 for both biomass (living and dead cells). The maximum uptake capacity of S. xylosus 222W (living and dead cells) was recorded at 37oC, the percentage removed being 75.90 vs. 84.92 %, respectively. It can be concluded that S. xylosus 222W exhibited high potential and affinity to remove of nickel ions from aqueous solution.

DEAD ZONE IN THE POLAR-CAP ACCELERATOR OF PULSARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Alexander Y.; Beloborodov, Andrei M.

We study plasma flows above pulsar polar caps using time-dependent simulations of plasma particles in the self-consistent electric field. The flow behavior is controlled by the dimensionless parameter {alpha} = j/c{rho}{sub GJ}, where j is the electric current density and {rho}{sub GJ} is the Goldreich-Julian charge density. The region of the polar cap where 0 < {alpha} < 1 is a {sup d}ead zone{sup -}in this zone, particle acceleration is inefficient and pair creation is not expected even for young, rapidly rotating pulsars. Pulsars with polar caps near the rotation axis are predicted to have a hollow-cone structure of radiomore » emission, as the dead zone occupies the central part of the polar cap. Our results apply to charge-separated flows of electrons (j < 0) or ions (j > 0). In the latter case, we consider the possibility of a mixed flow consisting of different ion species, and observe the development of two-stream instability. The dead zone at the polar cap is essential for the development of an outer gap near the null surface {rho}{sub GJ} = 0.« less

Foraging behavior of pileated woodpeckers in partial cut and uncut bottomland hardwood forest

USGS Publications Warehouse

Newell, P.; King, Sammy L.; Kaller, Michael D.

2009-01-01

In bottomland hardwood forests, partial cutting techniques are increasingly advocated and used to create habitat for priority wildlife like Louisiana black bear (Ursus americanus luteolus), white-tailed deer (Odocoileus virginianus), and Neotropical migrants. Although partial cutting may be beneficial to some species, those that use dead wood may be negatively affected since large diameter and poor quality trees (deformed, moribund, or dead) are rare, but normally targeted for removal. On the other hand, partial cutting can create dead wood if logging slash is left on-site. We studied foraging behavior of pileated woodpeckers (Dryocopus pileatus) in one- and two-year-old partial cuts designed to benefit priority species and in uncut forest during winter, spring, and summer of 2006 and 2007 in Louisiana. Males and females did not differ in their use of tree species, dbh class, decay class, foraging height, use of foraging tactics or substrate types; however, males foraged on larger substrates than females. In both partial cut and uncut forest, standing live trees were most frequently used (83% compared to 14% for standing dead trees and 3% for coarse woody debris); however, dead trees were selected (i.e. used out of proportion to availability). Overcup oak (Quercus lyrata) and bitter pecan (Carya aquatica) were also selected and sugarberry (Celtis laevigata) avoided. Pileated woodpeckers selected trees >= 50 cm dbh and avoided trees in smaller dbh classes (10-20 cm). Density of selected foraging substrates was the same in partial cut and uncut forest. Of the foraging substrates, woodpeckers spent 54% of foraging time on live branches and boles, 37% on dead branches and boles, and 9% on vines. Of the foraging tactics, the highest proportion of foraging time was spent excavating (58%), followed by pecking (14%), gleaning (14%), scaling (7%), berry-eating (4%), and probing (3%). Woodpecker use of foraging tactics and substrates, and foraging height and substrate diameter did not differ between recent partial cut and uncut forest. Partial cutting designed to improve or maintain habitat for priority wildlife did not affect pileated woodpecker foraging behavior or availability of selected trees compared to uncut forest in the short term.

Foraging behavior of pileated woodpeckers in partial cut and uncut bottomland hardwood forest

USGS Publications Warehouse

Newell, P.; King, S.; Kaller, M.

2009-01-01

In bottomland hardwood forests, partial cutting techniques are increasingly advocated and used to create habitat for priority wildlife like Louisiana black bear (Ursus americanus luteolus), white-tailed deer (Odocoileus virginianus), and Neotropical migrants. Although partial cutting may be beneficial to some species, those that use dead wood may be negatively affected since large diameter and poor quality trees (deformed, moribund, or dead) are rare, but normally targeted for removal. On the other hand, partial cutting can create dead wood if logging slash is left on-site. We studied foraging behavior of pileated woodpeckers (Dryocopus pileatus) in one- and two-year-old partial cuts designed to benefit priority species and in uncut forest during winter, spring, and summer of 2006 and 2007 in Louisiana. Males and females did not differ in their use of tree species, dbh class, decay class, foraging height, use of foraging tactics or substrate types; however, males foraged on larger substrates than females. In both partial cut and uncut forest, standing live trees were most frequently used (83% compared to 14% for standing dead trees and 3% for coarse woody debris); however, dead trees were selected (i.e. used out of proportion to availability). Overcup oak (Quercus lyrata) and bitter pecan (Carya aquatica) were also selected and sugarberry (Celtis laevigata) avoided. Pileated woodpeckers selected trees ???50 cm dbh and avoided trees in smaller dbh classes (10-20 cm). Density of selected foraging substrates was the same in partial cut and uncut forest. Of the foraging substrates, woodpeckers spent 54% of foraging time on live branches and boles, 37% on dead branches and boles, and 9% on vines. Of the foraging tactics, the highest proportion of foraging time was spent excavating (58%), followed by pecking (14%), gleaning (14%), scaling (7%), berry-eating (4%), and probing (3%). Woodpecker use of foraging tactics and substrates, and foraging height and substrate diameter did not differ between recent partial cut and uncut forest. Partial cutting designed to improve or maintain habitat for priority wildlife did not affect pileated woodpecker foraging behavior or availability of selected trees compared to uncut forest in the short term. ?? 2009 Elsevier B.V.

Whale and dolphin behavioural responses to dead conspecifics.

PubMed

Bearzi, Giovanni; Kerem, Dan; Furey, Nathan B; Pitman, Robert L; Rendell, Luke; Reeves, Randall R

2018-06-01

The scientific study of death across animal taxa-comparative thanatology-investigates how animals respond behaviourally, physiologically and psychologically to dead conspecifics, and the processes behind such responses. Several species of cetaceans have been long known to care for, attend to, be aroused by, or show interest in dead or dying individuals. We investigated patterns and variation in cetacean responses to dead conspecifics across cetacean taxa based on a comprehensive literature review. We analysed 78 records reported between 1970 and 2016, involving 20 of the 88 extant cetacean species. We adopted a weighted comparative approach to take observation effort into account and found that odontocetes (toothed cetaceans) were much more likely than mysticetes (baleen whales) to attend to dead conspecifics. Dolphins (Delphinidae) had the greatest occurrence of attentive behaviour (92.3% of all records), with a weighed attendance index 18 times greater than the average of all other cetacean families. Two dolphin genera, Sousa and Tursiops, constituted 55.1% of all cetacean records (N=43) and showed the highest incidence of attentive behaviour. Results of analyses intended to investigate the reasons behind these differences suggested that encephalisation may be an important predictor, consistent with the "social brain" hypothesis. Among attending individuals or groups of known sex (N=28), the majority (75.0%) were adult females with dead calves or juveniles (possibly their own offspring, with exceptions), consistent with the strong mother-calf bond, or, in a few cases, with the bond between mothers and other females in the group. The remaining records (25.0%) involved males either showing sexual interest in a dead adult or subadult, or carrying a dead calf in the presence of females. Because an inanimate individual is potentially rescuable, responses to dead conspecifics-especially by females-can be explained at least in part by attempts to revive and protect, having a clear adaptive value. In some cases such responses are followed by apparently maladaptive behaviour such as the long-term carrying of, or standing by, a decomposed carcass, similar to observations of certain terrestrial mammals. Among the possible explanations for the observed cetacean behavioural responses to dead conspecifics are strong attachment resulting in a difficulty of "letting go"-possibly related to grieving-or perhaps individuals failing to recognise or accept that an offspring or companion has died. Our current understanding is challenged by small sample size, incomplete descriptions, and lack of information on the physiology and neural processes underpinning the observed behaviour. We provide research recommendations that would improve such understanding. Copyright © 2018 Elsevier GmbH. All rights reserved.

Self-Interaction Chromatography of mAbs: Accurate Measurement of Dead Volumes.

PubMed

Hedberg, S H M; Heng, J Y Y; Williams, D R; Liddell, J M

2015-12-01

Measurement of the second virial coefficient B22 for proteins using self-interaction chromatography (SIC) is becoming an increasingly important technique for studying their solution behaviour. In common with all physicochemical chromatographic methods, measuring the dead volume of the SIC packed column is crucial for accurate retention data; this paper examines best practise for dead volume determination. SIC type experiments using catalase, BSA, lysozyme and a mAb as model systems are reported, as well as a number of dead column measurements. It was observed that lysozyme and mAb interacted specifically with Toyopearl AF-Formyl dead columns depending upon pH and [NaCl], invalidating their dead volume usage. Toyopearl AF-Amino packed dead columns showed no such problems and acted as suitable dead columns without any solution condition dependency. Dead volume determinations using dextran MW standards with protein immobilised SIC columns provided dead volume estimates close to those obtained using Toyopearl AF-Amino dead columns. It is concluded that specific interactions between proteins, including mAbs, and select SIC support phases can compromise the use of some standard approaches for estimating the dead volume of SIC columns. Two other methods were shown to provide good estimates for the dead volume.

VHDL implementation of feature-extraction algorithm for the PANDA electromagnetic calorimeter

NASA Astrophysics Data System (ADS)

Guliyev, E.; Kavatsyuk, M.; Lemmens, P. J. J.; Tambave, G.; Löhner, H.; Panda Collaboration

2012-02-01

A simple, efficient, and robust feature-extraction algorithm, developed for the digital front-end electronics of the electromagnetic calorimeter of the PANDA spectrometer at FAIR, Darmstadt, is implemented in VHDL for a commercial 16 bit 100 MHz sampling ADC. The source-code is available as an open-source project and is adaptable for other projects and sampling ADCs. Best performance with different types of signal sources can be achieved through flexible parameter selection. The on-line data-processing in FPGA enables to construct an almost dead-time free data acquisition system which is successfully evaluated as a first step towards building a complete trigger-less readout chain. Prototype setups are studied to determine the dead-time of the implemented algorithm, the rate of false triggering, timing performance, and event correlations.

Driving at Night Can Be Deadly

DOT National Transportation Integrated Search

1996-06-17

Efficient Commercial Vehicle Operations (CVO) is imperative as manufacturers and distributors move to new technologies, faster production methods and "Just in Time" delivery. CVO must offer more reliable travel times, as well as safety and flexibilit...

49 CFR 236.55 - Dead section; maximum length.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Dead section; maximum length. 236.55 Section 236... Instructions: All Systems Track Circuits § 236.55 Dead section; maximum length. Where dead section exceeds 35... over such dead section is less than 35 feet, the maximum length of the dead section shall not exceed...

49 CFR 236.55 - Dead section; maximum length.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Dead section; maximum length. 236.55 Section 236... Instructions: All Systems Track Circuits § 236.55 Dead section; maximum length. Where dead section exceeds 35... over such dead section is less than 35 feet, the maximum length of the dead section shall not exceed...

9 CFR 82.12 - Other interstate movements and special permits.

Code of Federal Regulations, 2014 CFR

2014-01-01

... for the disposal of dead birds or dead poultry that are infected with Newcastle disease, or dead birds or dead poultry from flocks infected with Newcastle disease, or manure generated by or eggs from... following: (i) The address of the place where the dead birds, dead poultry, manure, or eggs are located; and...

49 CFR 236.55 - Dead section; maximum length.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Dead section; maximum length. 236.55 Section 236... Instructions: All Systems Track Circuits § 236.55 Dead section; maximum length. Where dead section exceeds 35... over such dead section is less than 35 feet, the maximum length of the dead section shall not exceed...

49 CFR 236.55 - Dead section; maximum length.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Dead section; maximum length. 236.55 Section 236... Instructions: All Systems Track Circuits § 236.55 Dead section; maximum length. Where dead section exceeds 35... over such dead section is less than 35 feet, the maximum length of the dead section shall not exceed...

49 CFR 236.55 - Dead section; maximum length.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Dead section; maximum length. 236.55 Section 236... Instructions: All Systems Track Circuits § 236.55 Dead section; maximum length. Where dead section exceeds 35... over such dead section is less than 35 feet, the maximum length of the dead section shall not exceed...

Statistical aspects of point count sampling

USGS Publications Warehouse

Barker, R.J.; Sauer, J.R.; Ralph, C.J.; Sauer, J.R.; Droege, S.

1995-01-01

The dominant feature of point counts is that they do not census birds, but instead provide incomplete counts of individuals present within a survey plot. Considering a simple model for point count sampling, we demon-strate that use of these incomplete counts can bias estimators and testing procedures, leading to inappropriate conclusions. A large portion of the variability in point counts is caused by the incomplete counting, and this within-count variation can be confounded with ecologically meaningful varia-tion. We recommend caution in the analysis of estimates obtained from point counts. Using; our model, we also consider optimal allocation of sampling effort. The critical step in the optimization process is in determining the goals of the study and methods that will be used to meet these goals. By explicitly defining the constraints on sampling and by estimating the relationship between precision and bias of estimators and time spent counting, we can predict the optimal time at a point for each of several monitoring goals. In general, time spent at a point will differ depending on the goals of the study.

Assessing the living and dead proportions of cold-water coral colonies: implications for deep-water Marine Protected Area monitoring in a changing ocean.

PubMed

Vad, Johanne; Orejas, Covadonga; Moreno-Navas, Juan; Findlay, Helen S; Roberts, J Murray

2017-01-01

Coral growth patterns result from an interplay of coral biology and environmental conditions. In this study colony size and proportion of live and dead skeletons in the cold-water coral (CWC) Lophelia pertusa (Linnaeus, 1758) were measured using video footage from Remotely Operated Vehicle (ROV) transects conducted at the inshore Mingulay Reef Complex (MRC) and at the offshore PISCES site (Rockall Bank) in the NE Atlantic. The main goal of this paper was to explore the development of a simple method to quantify coral growth and its potential application as an assessment tool of the health of these remote habitats. Eighteen colonies were selected and whole colony and dead/living layer size were measured. Live to dead layer ratios for each colony were then determined and analysed. The age of each colony was estimated using previously published data. Our paper shows that: (1) two distinct morphotypes can be described: at the MRC, colonies displayed a 'cauliflower-shaped' morphotype whereas at the PISCES site, colonies presented a more flattened 'bush-shaped' morphotype; (2) living layer size was positively correlated with whole colony size; (3) live to dead layer ratio was negatively correlated to whole colony size; (4) live to dead layer ratio never exceeded 0.27. These results suggest that as a colony develops and its growth rate slows down, the proportion of living polyps in the colony decreases. Furthermore, at least 73% of L. pertusa colonies are composed of exposed dead coral skeleton, vulnerable to ocean acidification and the associated shallowing of the aragonite saturation horizon, with significant implications for future deep-sea reef framework integrity. The clear visual contrast between white/pale living and grey/dark dead portions of the colonies also gives a new way by which they can be visually monitored over time. The increased use of marine autonomous survey vehicles offers an important new platform from which such a surveying technique could be applied to monitor deep-water marine protected areas in the future.

Abrupt aridities in the Levant-Sahel linked with solar activities

NASA Astrophysics Data System (ADS)

Stein, M.; Kushnir, Y.

2012-04-01

Observations of 19th and 20th century precipitation in the Dead Sea watershed region display a multidecadal, anti-phase relationship to North Atlantic (NAtl) sea surface temperature (SST) variability, such that when the NAtl is relatively cold, Jerusalem experiences higher than normal precipitation and vice versa. This association is underlined by a negative correlation to precipitation in the sub-Saharan Sahel and a positive correlation to precipitation in western North America, areas that are also affected by multidecadal NAtl SST variability. These observations are consistent with broad range of Holocene hydroclimatic fluctuations from the epochal, to the millennial and centennial time scales, as displayed by the Dead Sea and Sahelian lake levels and by direct and indirect proxy indicators of NAtl SSTs. On the epochal time scale, the gradual cooling of NAtl SSTs throughout the Holocene in response to precession-driven reduction of summer insolation is associated with previously well-studied wet-to-dry transition in the Sahel and with a general increase in Dead Sea lake levels from low stands after the Younger Dryas to higher stands in the mid- to late-Holocene. On the millennial and centennial time scales there is also evidence for an antiphase relationship between Holocene variations in the Dead Sea and Sahelian lake levels and with proxy indicators of NAtl SSTs. However, the records are punctuated by abrupt lake-level drops and extensive expansion of the desert belt at ~8.1, 5.7, 3.3 and 1.4 ka cal BP, which appear to be in-phase and which occur during previously documented abrupt major cooling events in the Northern Hemisphere. We link these cooling to solar activity variations that were identified in the North Atlantic IRD and cosmogenic isotopes records.

Biosorption of Cd(II) by live and dead cells of Bacillus cereus RC-1 isolated from cadmium-contaminated soil.

PubMed

Huang, Fei; Dang, Zhi; Guo, Chu-Ling; Lu, Gui-Ning; Gu, Roy R; Liu, Hong-Juan; Zhang, Hui

2013-07-01

The present study investigated the biosorption capacity of live and dead cells of Bacillus cereus RC-1 for Cd(II). The biosorption characteristics were investigated as a function of initial pH, contact time, and initial cadmium concentration. Equilibrium biosorption was modeled using Langmuir, Freundlich and Redlich-Peterson isotherm equations. It was found that the maximum biosorption capacities calculated from Langmuir isotherm were 31.95 mg/g and 24.01 mg/g for dead cells and live cells, respectively. The kinetics of the biosorption was better described by pseudo-second order kinetic model. Desorption efficiency of biosorbents was investigated at various pH values. These results indicated that dead cells have higher Cd(II) biosorption capacity than live cells. Furthermore, zeta potential, transmission electron microscopy (TEM), scanning electron microscopy (SEM) coupled with energy dispersive X-ray (EDX), and Fourier transform infrared spectroscopy (FTIR) studies were carried out to understand the differences in the Cd(II) biosorption behavior for the both biosorbents. The bioaccumulation of Cd(II) by B. cereus RC-1 was found to depend largely on extracellular biosorption rather than intracellular accumulation. Based on the above studies, dead biomass appears to be a more efficient biosorbent for the removal of Cd(II) from aqueous solution. Copyright © 2013 Elsevier B.V. All rights reserved.

Bacteria associated with decomposing dead wood in a natural temperate forest.

PubMed

Tláskal, Vojtech; Zrustová, Petra; Vrška, Tomáš; Baldrian, Petr

2017-12-01

Dead wood represents an important pool of organic matter in forests and is one of the sources of soil formation. It has been shown to harbour diverse communities of bacteria, but their roles in this habitat are still poorly understood. Here, we describe the bacterial communities in the dead wood of Abies alba, Picea abies and Fagus sylvatica in a temperate natural forest in Central Europe. An analysis of environmental factors showed that decomposing time along with pH and water content was the strongest drivers of community composition. Bacterial biomass positively correlated with N content and increased with decomposition along with the concurrent decrease in the fungal/bacterial biomass ratio. Rhizobiales and Acidobacteriales were abundant bacterial orders throughout the whole decay process, but many bacterial taxa were specific either for young (<15 years) or old dead wood. During early decomposition, bacterial genera able to fix N2 and to use simple C1 compounds (e.g. Yersinia and Methylomonas) were frequent, while wood in advanced decay was rich in taxa typical of forest soils (e.g. Bradyrhizobium and Rhodoplanes). Although the bacterial contribution to dead wood turnover remains unclear, the community composition appears to reflect the changing conditions of the substrate and suggests broad metabolic capacities of its members. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Evolution of genomic diversity and sex at extreme environments: Fungal life under hypersaline Dead Sea stress

PubMed Central

Kis-Papo, Tamar; Kirzhner, Valery; Wasser, Solomon P.; Nevo, Eviatar

2003-01-01

We have found that genomic diversity is generally positively correlated with abiotic and biotic stress levels (1–3). However, beyond a high-threshold level of stress, the diversity declines to a few adapted genotypes. The Dead Sea is the harshest planetary hypersaline environment (340 g·liter–1 total dissolved salts, ≈10 times sea water). Hence, the Dead Sea is an excellent natural laboratory for testing the “rise and fall” pattern of genetic diversity with stress proposed in this article. Here, we examined genomic diversity of the ascomycete fungus Aspergillus versicolor from saline, nonsaline, and hypersaline Dead Sea environments. We screened the coding and noncoding genomes of A. versicolor isolates by using >600 AFLP (amplified fragment length polymorphism) markers (equal to loci). Genomic diversity was positively correlated with stress, culminating in the Dead Sea surface but dropped drastically in 50- to 280-m-deep seawater. The genomic diversity pattern paralleled the pattern of sexual reproduction of fungal species across the same southward gradient of increasing stress in Israel. This parallel may suggest that diversity and sex are intertwined intimately according to the rise and fall pattern and adaptively selected by natural selection in fungal genome evolution. Future large-scale verification in micromycetes will define further the trajectories of diversity and sex in the rise and fall pattern. PMID:14645702

9 CFR 82.12 - Other interstate movements and special permits.

Code of Federal Regulations, 2012 CFR

2012-01-01

... required for the disposal of dead birds or dead poultry that are infected with END, or dead birds or dead..., the special permit will also include the following: (i) The address of the place where the dead birds, dead poultry, manure, or eggs are located; and (ii) The number and type of birds, poultry, or other...

9 CFR 82.12 - Other interstate movements and special permits.

Code of Federal Regulations, 2010 CFR

2010-01-01

... required for the disposal of dead birds or dead poultry that are infected with END, or dead birds or dead..., the special permit will also include the following: (i) The address of the place where the dead birds, dead poultry, manure, or eggs are located; and (ii) The number and type of birds, poultry, or other...

9 CFR 82.12 - Other interstate movements and special permits.

Code of Federal Regulations, 2013 CFR

2013-01-01

... required for the disposal of dead birds or dead poultry that are infected with END, or dead birds or dead..., the special permit will also include the following: (i) The address of the place where the dead birds, dead poultry, manure, or eggs are located; and (ii) The number and type of birds, poultry, or other...

9 CFR 82.12 - Other interstate movements and special permits.

Code of Federal Regulations, 2011 CFR

2011-01-01

... required for the disposal of dead birds or dead poultry that are infected with END, or dead birds or dead..., the special permit will also include the following: (i) The address of the place where the dead birds, dead poultry, manure, or eggs are located; and (ii) The number and type of birds, poultry, or other...

Avian mortality events in the United States caused by anticholinesterase pesticides: A retrospective summary of National Wildlife Health Center records from 1980 to 2000

USGS Publications Warehouse

Fleischli, Margaret A.; Franson, J.C.; Thomas, N.J.; Finley, D.L.; Riley, Walter

2004-01-01

We reviewed the U.S. Geological Survey National Wildlife Health Center (NWHC) mortality database from 1980 to 2000 to identify cases of poisoning caused by organophosphorus and carbamate pesticides. From the 35,022 cases from which one or more avian carcasses were submitted to the NWHC for necropsy, we identified 335 mortality events attributed to anticholinesterase poisoning, 119 of which have been included in earlier reports. Poisoning events were classified as confirmed (n = 205) when supported by findings of ≥50% inhibition of cholinesterase (ChE) activity in brain tissue and the detection of a specific pesticide in the gastrointestinal contents of one or more carcasses. Suspected poisonings (n = 130) were defined as cases where brain ChE activity was ≥50% inhibited or a specific pesticide was identified in gastrointestinal contents. The 335 avian mortality events occurred in 42 states. Washington, Virginia, and Ohio had the highest frequency of events, with 24 (7.2%), 21 (6.3%), and 20 (6.0%) events, respectively. A total of 8877 carcasses of 103 avian species in 12 orders was recovered. Because carcass counts underestimate total mortality, this represents the minimum actual mortality. Of 24 different pesticides identified, the most frequent were famphur (n = 59; 18%), carbofuran (n = 52; 15%), diazinon (n = 40; 12%), and fenthion (n = 17; 5.1%). Falconiformes were reported killed most frequently (49% of all die-offs) but Anseriformes were found dead in the greatest numbers (64% of 8877 found dead). The majority of birds reported killed by famphur were Passeriformes and Falconiformes, with the latter found dead in 90% of famphur-related poisoning events. Carbofuran and famphur were involved in mortality of the greatest variety of species (45 and 33, respectively). Most of the mortality events caused by diazinon involved waterfowl.

Towards the establishment of a general rate law for gypsum nucleation

NASA Astrophysics Data System (ADS)

Reznik, Itay J.; Ganor, Jiwchar; Gruber, Chen; Gavrieli, Ittai

2012-05-01

Gypsum nucleation kinetics from a wide range of chemical compositions (1.45 < Ca2+/SO42- < 115), ionic strengths (I = 2.5-10 m) and saturation state with respect to gypsum (Ωgyp = 1.07-8.4) were examined in batch experiments containing mixtures of Ca2+-rich Dead Sea brine and SO42-rich seawater with or without addition of extra Na2SO4 and CaCl2·2H2O. The induction times attained in the present study were compiled together with literature values from experiments carried out under significantly different conditions (synthetic NaCl solutions; I = 0.09-6.3 m; Ca2+/SO42- = 1; Ωgyp:1.59-7.76). Despite the variability in the experimental solutions, a single rate law based on classic nucleation theory was formulated to describe the induction times from more than 80 experiments: logT=log{1}/{3.17·Cs·exp{-}7.08ln2Ω}+0.072·Cs·exp-{1.426}/{ln2Ω} where Tind is the induction time, Cs is the solubility of gypsum and Ω is the saturation state with respect to gypsum. The rate law provides Tind for gypsum precipitation from aqueous solutions at 25 °C, containing no synthetic antiscalants or catalysts, within a 95% confidence interval within a factor of 5. Based on this rate law, we show that at present most of the precipitation of gypsum from the Dead Sea brine occurs following significant evaporation in the industrial evaporation ponds and not in the Dead Sea itself. Whereas Tind in Dead Sea brines is very long (on the order of 3 years), the evaporation of brine in the industrial ponds leads to increased Ω values, and thus to short Tind in the order of a few days. However, if seawater or reject brine from seawater desalinization will be introduced to the Dead Sea to restore its declining level, Tind will be significantly reduced and gypsum nucleation and precipitation will occur. For evaporated seawater, the proposed rate law predicts that even though saturation is obtained when seawater is evaporated by a factor of 2.8, gypsum will nucleate at reasonable times (few years) only when seawater are evaporated by a factor of ˜3.3.

Detection of viable Salmonella in ice cream by TaqMan real-time polymerase chain reaction assay combining propidium monoazide.

PubMed

Wang, Yuexia; Yang, Ming; Liu, Shuchun; Chen, Wanyi; Suo, Biao

2015-09-01

Real-time polymerase chain reaction (PCR) allows rapid detection of Salmonella in frozen dairy products, but it might cause a false positive detection result because it might amplify DNA from dead target cells as well. In this study, Salmonella-free frozen ice cream was initially inoculated with heat-killed Salmonella Typhimurium cells and stored at -18°C. Bacterial DNA extracted from the sample was amplified using TaqMan probe-based real-time PCR targeting the invA gene. Our results indicated that DNA from the dead cells remained stable in frozen ice cream for at least 20 days, and could produce fluorescence signal for real-time PCR as well. To overcome this limitation, propidium monoazide (PMA) was combined with real-time PCR. PMA treatment can effectively prevent PCR amplification from heat-killed Salmonella cells in frozen ice cream. The PMA real-time PCR assay can selectively detect viable Salmonella at as low as 10 3  CFU/mL. Combining 18 hours of pre-enrichment with the assay allows for the detection of viable Salmonella at 10 0  CFU/mL and avoiding the false-positive result of dead cells. The PMA real-time PCR assay provides an alternative specifically for detection of viable Salmonella in ice cream. However, when the PMA real-time PCR assay was evaluated in ice cream subjected to frozen storage, it obviously underestimated the contamination situation of viable Salmonella, which might lead to a false negative result. According to this result, the use of enrichment prior to PMA real-time PCR analysis remains as the more appropriate approach. Copyright © 2015. Published by Elsevier B.V.

Modeling and simulation of count data.

PubMed

Plan, E L

2014-08-13

Count data, or number of events per time interval, are discrete data arising from repeated time to event observations. Their mean count, or piecewise constant event rate, can be evaluated by discrete probability distributions from the Poisson model family. Clinical trial data characterization often involves population count analysis. This tutorial presents the basics and diagnostics of count modeling and simulation in the context of pharmacometrics. Consideration is given to overdispersion, underdispersion, autocorrelation, and inhomogeneity.

The ATP/DNA Ratio Is a Better Indicator of Islet Cell Viability Than the ADP/ATP Ratio

PubMed Central

Suszynski, T.M.; Wildey, G.M.; Falde, E.J.; Cline, G.W.; Maynard, K. Stewart; Ko, N.; Sotiris, J.; Naji, A.; Hering, B.J.; Papas, K.K.

2009-01-01

Real-time, accurate assessment of islet viability is critical for avoiding transplantation of nontherapeutic preparations. Measurements of the intracellular ADP/ATP ratio have been recently proposed as useful prospective estimates of islet cell viability and potency. However, dead cells may be rapidly depleted of both ATP and ADP, which would render the ratio incapable of accounting for dead cells. Since the DNA of dead cells is expected to remain stable over prolonged periods of time (days), we hypothesized that use of the ATP/DNA ratio would take into account dead cells and may be a better indicator of islet cell viability than the ADP/ATP ratio. We tested this hypothesis using mixtures of healthy and lethally heat-treated (HT) rat insulinoma cells and human islets. Measurements of ATP/DNA and ADP/ATP from the known mixtures of healthy and HT cells and islets were used to evaluate how well these parameters correlated with viability. The results indicated that ATP and ADP were rapidly (within 1 hour) depleted in HT cells. The fraction of HT cells in a mixture correlated linearly with the ATP/DNA ratio, whereas the ADP/ADP ratio was highly scattered, remaining effectively unchanged. Despite similar limitations in both ADP/ADP and ATP/DNA ratios, in that ATP levels may fluctuate significantly and reversibly with metabolic stress, the results indicated that ATP/DNA was a better measure of islet viability than the ADP/ATP ratio. PMID:18374063

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, K. S.; Nakae, L. F.; Prasad, M. K.

Here, we solve a simple theoretical model of time evolving fission chains due to Feynman that generalizes and asymptotically approaches the point model theory. The point model theory has been used to analyze thermal neutron counting data. This extension of the theory underlies fast counting data for both neutrons and gamma rays from metal systems. Fast neutron and gamma-ray counting is now possible using liquid scintillator arrays with nanosecond time resolution. For individual fission chains, the differential equations describing three correlated probability distributions are solved: the time-dependent internal neutron population, accumulation of fissions in time, and accumulation of leaked neutronsmore » in time. Explicit analytic formulas are given for correlated moments of the time evolving chain populations. The equations for random time gate fast neutron and gamma-ray counting distributions, due to randomly initiated chains, are presented. Correlated moment equations are given for both random time gate and triggered time gate counting. There are explicit formulas for all correlated moments are given up to triple order, for all combinations of correlated fast neutrons and gamma rays. The nonlinear differential equations for probabilities for time dependent fission chain populations have a remarkably simple Monte Carlo realization. A Monte Carlo code was developed for this theory and is shown to statistically realize the solutions to the fission chain theory probability distributions. Combined with random initiation of chains and detection of external quanta, the Monte Carlo code generates time tagged data for neutron and gamma-ray counting and from these data the counting distributions.« less

A dual near-infrared and dielectric spectroscopies strategy to monitor populations of Chinese hamster ovary cells in bioreactor.

PubMed

Courtès, Franck; Ebel, Bruno; Guédon, Emmanuel; Marc, Annie

2016-05-01

to develop a new strategy combining near-infrared (NIR) and dielectric spectroscopies for real-time monitoring and in-depth characterizing populations of Chinese hamster ovary cells throughout cultures performed in bioreactors. Spectral data processing was based on off-line analyses of the cells, including trypan blue exclusion method, and lactate dehydrogenase activity (LDH). Viable cell density showed a linear correlation with permittivity up to 6 × 10(6) cells ml(-1), while a logarithmic correlation was found between non-lysed dead cell density and conductivity up to 10(7) cells ml(-1). Additionally, partial least square technique was used to develop a calibration model of the supernatant LDH activity based on online NIR spectra with a RMSEC of 55 U l(-1). Considering the LDH content of viable cells measured to be 110 U per 10(9) cells, the lysed dead cell density could be then estimated. These calibration models provided real-time prediction accuracy (R(2) ≥ 0.95) for the three types of cell populations. The high potential of a dual spectroscopy strategy to enhance the online bioprocesses characterization is demonstrated since it allows the simultaneous determination of viable, dead and lysed cell populations in real time.

SlDEAD31, a Putative DEAD-Box RNA Helicase Gene, Regulates Salt and Drought Tolerance and Stress-Related Genes in Tomato.

PubMed

Zhu, Mingku; Chen, Guoping; Dong, Tingting; Wang, Lingling; Zhang, Jianling; Zhao, Zhiping; Hu, Zongli

2015-01-01

The DEAD-box RNA helicases are involved in almost every aspect of RNA metabolism, associated with diverse cellular functions including plant growth and development, and their importance in response to biotic and abiotic stresses is only beginning to emerge. However, none of DEAD-box genes was well characterized in tomato so far. In this study, we reported on the identification and characterization of two putative DEAD-box RNA helicase genes, SlDEAD30 and SlDEAD31 from tomato, which were classified into stress-related DEAD-box proteins by phylogenetic analysis. Expression analysis indicated that SlDEAD30 was highly expressed in roots and mature leaves, while SlDEAD31 was constantly expressed in various tissues. Furthermore, the expression of both genes was induced mainly in roots under NaCl stress, and SlDEAD31 mRNA was also increased by heat, cold, and dehydration. In stress assays, transgenic tomato plants overexpressing SlDEAD31 exhibited dramatically enhanced salt tolerance and slightly improved drought resistance, which were simultaneously demonstrated by significantly enhanced expression of multiple biotic and abiotic stress-related genes, higher survival rate, relative water content (RWC) and chlorophyll content, and lower water loss rate and malondialdehyde (MDA) production compared to wild-type plants. Collectively, these results provide a preliminary characterization of SlDEAD30 and SlDEAD31 genes in tomato, and suggest that stress-responsive SlDEAD31 is essential for salt and drought tolerance and stress-related gene regulation in plants.

Effects of Point Count Duration, Time-of-Day, and Aural Stimuli on Detectability of Migratory and Resident Bird Species in Quintana Roo, Mexico

Treesearch

James F. Lynch

1995-01-01

Effects of count duration, time-of-day, and aural stimuli were studied in a series of unlimited-radius point counts conducted during winter in Quintana Roo, Mexico. The rate at which new species were detected was approximately three times higher during the first 5 minutes of each 15- minute count than in the final 5 minutes. The number of individuals and species...

North Atlantic influence on 19th-20th century rainfall in the Dead Sea watershed, teleconnections with the Sahel, and implication for Holocene climate fluctuations

NASA Astrophysics Data System (ADS)

Kushnir, Yochanan; Stein, Mordechai

2010-12-01

The importance of understanding processes that govern the hydroclimate of the Mediterranean Basin is highlighted by the projected significant drying of the region in response to the increase in greenhouse gas concentrations. Here we study the long-term hydroclimatic variability of the central Levant region, situated in the eastern boundary of the Basin, as reveled by instrumental observations and the Holocene record of Dead Sea level variations. Observations of 19th and 20th century precipitation in the Dead Sea watershed region display a multidecadal, anti-phase relationship to North Atlantic (NAtl) sea surface temperature (SST) variability, such that when the NAtl is relatively cold, Jerusalem experiences higher than normal precipitation and vice versa. This association is underlined by a negative correlation to precipitation in the sub-Saharan Sahel and a positive correlation to precipitation in western North America, areas that are also affected by multidecadal NAtl SST variability. These observations are consistent with a broad range of Holocene hydroclimatic fluctuations from the epochal, to the millennial and centennial time scales, as displayed by the Dead Sea lake level, by lake levels in the Sahel, and by direct and indirect proxy indicators of NAtl SSTs. On the epochal time scale, the gradual cooling of NAtl SSTs throughout the Holocene in response to precession-driven reduction of summer insolation is associated with previously well-studied wet-to-dry transition in the Sahel and with a general increase in Dead Sea lake levels from low stands after the Younger Dryas to higher stands in the mid- to late-Holocene. On the millennial and centennial time scales there is also evidence for an anti-phase relationship between Holocene variations in the Dead Sea and Sahelian lake levels and with proxy indicators of NAtl SSTs. However the records are punctuated by abrupt lake-level drops, which appear to be in-phase and which occur during previously documented abrupt major cooling events in the Northern Hemisphere. We propose that the mechanisms by which NAtl SSTs affect precipitation in the central Levant is related to the tendency for high (low) pressure anomalies to persist over the eastern North Atlantic/Western Mediterranean region when the Basin is cold (warm). This, in turn, affects the likelihood of cold air outbreaks and cyclogenesis in the Eastern Mediterranean and, consequently, rainfall in the central Levant region. Depending on its phase, this natural mechanism can alleviate or exacerbate the anthropogenic impact on the regions' hydroclimatic future.

A new modelling and identification scheme for time-delay systems with experimental investigation: a relay feedback approach

NASA Astrophysics Data System (ADS)

Pandey, Saurabh; Majhi, Somanath; Ghorai, Prasenjit

2017-07-01

In this paper, the conventional relay feedback test has been modified for modelling and identification of a class of real-time dynamical systems in terms of linear transfer function models with time-delay. An ideal relay and unknown systems are connected through a negative feedback loop to bring the sustained oscillatory output around the non-zero setpoint. Thereafter, the obtained limit cycle information is substituted in the derived mathematical equations for accurate identification of unknown plants in terms of overdamped, underdamped, critically damped second-order plus dead time and stable first-order plus dead time transfer function models. Typical examples from the literature are included for the validation of the proposed identification scheme through computer simulations. Subsequently, the comparisons between estimated model and true system are drawn through integral absolute error criterion and frequency response plots. Finally, the obtained output responses through simulations are verified experimentally on real-time liquid level control system using Yokogawa Distributed Control System CENTUM CS3000 set up.

Ultraviolet radiation properties as applied to photoclimatherapy at the Dead Sea.

PubMed

Kudish, A I; Abels, D; Harari, M

2003-05-01

The Dead Sea basin, the lowest terrestrial point on earth, is recognized as a natural treatment center for patients with various cutaneous and rheumatic diseases. Psoriasis is the major skin disease treated at the Dead Sea with excellent improvement to complete clearance exceeding 85% after 4 weeks of treatment. These results were postulated to be associated with a unique spectrum of ultraviolet radiation present in the Dead Sea area. The UVB and UVA radiation at two sites is measured continuously by identical sets of broad-band Solar Light Co. Inc. meters (Philadelphia, PA). The spectral selectivity within the UVB and UVA spectrum was determined using a narrow-band spectroradiometer, UV-Optronics 742 (Orlando, FL). The optimum exposure time intervals for photoclimatherapy, defined as the minimum ratio of erythema to therapeutic radiation intensities, were also determined using a Solar Light Co. Inc. Microtops II, Ozone Monitor-Sunphotometer. The ultraviolet radiation at the Dead Sea is attenuated relative to Beer Sheva as a result of the increased optical path length and consequent enhanced scattering. The UVB radiation is attenuated to a greater extent than UVA and the shorter erythema UVB spectral range decreased significantly compared with the longer therapeutic UVB wavelengths. It was demonstrated that the relative attenuation within the UVB spectral range is greatest for the shorter erythema rays and less for the longer therapeutic UVB wavelengths, thus producing a greater proportion of the longer therapeutic UVB wavelengths in the ultraviolet spectrum. These measurements can be utilized to minimize the exposure to solar radiation by correlating the cumulative UVB radiation dose to treatment efficacy and by formulating a patient sun exposure treatment protocol for Dead Sea photoclimatherapy.

A comparative study on the anti-schistosomal and hepatoprotective effects of vinpocetine and isosorbide-5-mononitrate on Schistosoma mansoni-infected mice.

PubMed

Alhusseiny, Samar M; El-Beshbishi, Samar N; Hashim, Maha M Abu; El-Nemr, Hosam El-Dein E; Handoussa, Aya E

2017-12-01

Schistosomiasis is a remarkable public health problem in developing countries. Presently, praziquantel is the optional drug for all human schistosomiasis. Owing to the increased praziquantel resistance, there is an urgent need to develop new alternatives. This study aims at determining the anti-schistosomal and/or the hepatoprotective effects of the anti-inflammatory drug; vinpocetine, and the vasodilator and the nitric oxide donor; isosorbide-5-mononitrate, in comparison to praziquantel. In the present research, the therapeutic efficacies of these drugs were assessed in Swiss albino female mice (CD-I strain) experimentally infected with an Egyptian strain of Schistosoma mansoni, using some general, parasitological, and histopathological parameters. In this work, praziquantel significantly reduced worm burden and hepatic egg load, increased the percentage of dead eggs in the small intestine and decreased granuloma count, but did not reduce granuloma diameter. While, either vinpocetine or isosorbide-5-mononitrate monotherapy did not induce significant reduction in the worm count, hepatic egg load or shift in the oogram pattern, but significantly reduced granuloma count and diameter. Moreover, isosorbide-5-mononitrate significantly reduced hepatic inflammation and necrosis. The best results were obtained in the mice groups treated with isosorbide-5-mononitrate combined with praziquantel or vinpocetine. Our results point to vinpocetine and isosorbide-5-mononitrate as a convenient and promising adjuvant to praziquantel for ameliorating schistosomal liver pathology. Further studies are recommended to reveal the actual pathways responsible for the different activities of vinpocetine and isosorbide-5-mononitrate. Copyright © 2017 Elsevier B.V. All rights reserved.

9 CFR 82.6 - Interstate movement of dead birds and dead poultry from a quarantined area.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Interstate movement of dead birds and dead poultry from a quarantined area. 82.6 Section 82.6 Animals and Animal Products ANIMAL AND PLANT... (END) § 82.6 Interstate movement of dead birds and dead poultry from a quarantined area. (a) Except as...

9 CFR 82.6 - Interstate movement of dead birds and dead poultry from a quarantined area.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Interstate movement of dead birds and dead poultry from a quarantined area. 82.6 Section 82.6 Animals and Animal Products ANIMAL AND PLANT... movement of dead birds and dead poultry from a quarantined area. (a) Except as provided in paragraph (b) of...

9 CFR 82.6 - Interstate movement of dead birds and dead poultry from a quarantined area.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Interstate movement of dead birds and dead poultry from a quarantined area. 82.6 Section 82.6 Animals and Animal Products ANIMAL AND PLANT... (END) § 82.6 Interstate movement of dead birds and dead poultry from a quarantined area. (a) Except as...

Bayesian analyses of time-interval data for environmental radiation monitoring.

PubMed

Luo, Peng; Sharp, Julia L; DeVol, Timothy A

2013-01-01

Time-interval (time difference between two consecutive pulses) analysis based on the principles of Bayesian inference was investigated for online radiation monitoring. Using experimental and simulated data, Bayesian analysis of time-interval data [Bayesian (ti)] was compared with Bayesian and a conventional frequentist analysis of counts in a fixed count time [Bayesian (cnt) and single interval test (SIT), respectively]. The performances of the three methods were compared in terms of average run length (ARL) and detection probability for several simulated detection scenarios. Experimental data were acquired with a DGF-4C system in list mode. Simulated data were obtained using Monte Carlo techniques to obtain a random sampling of the Poisson distribution. All statistical algorithms were developed using the R Project for statistical computing. Bayesian analysis of time-interval information provided a similar detection probability as Bayesian analysis of count information, but the authors were able to make a decision with fewer pulses at relatively higher radiation levels. In addition, for the cases with very short presence of the source (< count time), time-interval information is more sensitive to detect a change than count information since the source data is averaged by the background data over the entire count time. The relationships of the source time, change points, and modifications to the Bayesian approach for increasing detection probability are presented.

Ultrafast time measurements by time-correlated single photon counting coupled with superconducting single photon detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shcheslavskiy, V., E-mail: vis@becker-hickl.de; Becker, W.; Morozov, P.

Time resolution is one of the main characteristics of the single photon detectors besides quantum efficiency and dark count rate. We demonstrate here an ultrafast time-correlated single photon counting (TCSPC) setup consisting of a newly developed single photon counting board SPC-150NX and a superconducting NbN single photon detector with a sensitive area of 7 × 7 μm. The combination delivers a record instrument response function with a full width at half maximum of 17.8 ps and system quantum efficiency ∼15% at wavelength of 1560 nm. A calculation of the root mean square value of the timing jitter for channels withmore » counts more than 1% of the peak value yielded about 7.6 ps. The setup has also good timing stability of the detector–TCSPC board.« less

The Influence of Osmolytes on the Antimicrobial Activity of Silver Nanoparticles

NASA Astrophysics Data System (ADS)

Reed-Jones, Neiunna L.

Silver nanoparticles (Ag-NPs) are gaining popularity as antimicrobial agents due to their broad- spectrum activity and lower propensity to develop resistance in bacteria. However, with increased frequency of use, there remains a possibility for bacteria to develop resistance or adaptive mechanisms against Ag-NPs overtime. Mechanisms used by bacteria to resist antimicrobial agents include efflux pumps, heat shock proteins (Hsp) and accumulation of compatible solutes, generally referred to as osmolytes. The latter mechanism is typically employed when bacteria are under osmotic stress they accumulate osmolytes either through de novo synthesis or exogenously. Osmolytes act to stabilize the bacterial cell membrane by maintaining the native protein structure, while at the same time, ensuring compatibility with other cellular structures and functions. The most common osmolytes accumulated by bacteria are glycine betaine, proline, carnitine, choline, trehalose and glutamate. Since Ag-NPs target the cell membrane it is conceivable that osmolytes may suppress its bactericidal activity. In the present study, we assess the antimicrobial efficacy of Ag-NPs in the presence of glycine betaine and proline. Exponential phase cultures (106 cfu/ml) of Escherichia coli O157:H7, Listeria monocytogenes, Pseudomonas aeruginosa and Staphylococcus aureus were exposed to a predetermined the minimum inhibitory concentration (MIC) of 0.4 mM of citrate-stabilized Ag-NPs and incubated at 37°C for 48 h. This was replicated with the addition of 1 mM of either glycine betaine or proline. Growth was monitored by optical density, standard plate count, resazurin assay and LIVE/DEAD analyses. The result showed that Ag-NPs had no detectable effect on osmolyte treated cells. The average plate count of cultures supplemented with either glycine betaine or proline ranged from 108 to 109 cfu/ml after 48 h. Resazurin assay also showed that there was a significant increase in the cells supplemented with glycine betaine, 90% for E.coli O157:H7 and 44.3% for L. monocytogenes. No detectable metabolic activity was observed in the cells exposed to Ag-NPs alone. These results were corroborated by LIVE/DEAD analyses, which revealed over 86% cell viability in L. monocytogenes and E.coli O157:H7 treated with the osmolytes compared to 0.3% viability in those treated with Ag-NPs alone. SDS-PAGE analysis of the periplasmic proteins of the cells treated with Ag-NP and glycine betaine showed no qualitative difference in the protein profiles compared to the control cells grown in Trypticase Soy Broth alone. However, protein bands of cells treated with proline showed detectable difference relative to the control. The present findings suggest that glycine betaine and proline can suppress the antimicrobial activity of Ag-NPs.

Transducer Workshop (17th) Held in San Diego, California on June 22-24, 1993

DTIC Science & Technology

1993-06-01

weight in a drop tower, such as the primer tester shown in figure 1. The calibration procedure must be repeated for each lot of copper inserts, and small...force vs. time curve (i.e impulse = area unxer the curve). The FPyF can be used in the primer tester (shown in figure 1) as well as in a weapon...microphones. Plstonphone Output 124 dB, 250 Hz DEAD WEIGHT TESTIER USED AS A PRESSURE RELEASE CALIBRATOR The dead weight tester is designed and most

Organochlorine residues and reproduction in the big brown bat

USGS Publications Warehouse

Clark, D.R.; Lamont, T.G.

1976-01-01

Twenty-six pregnant big brown bats (Eptesicus fuscus) were collected at Montpelier Barn, Laurel, Maryland, and kept in individual cages until parturition. Seven young in 5 litters were born dead; 21 litters contained only living young. Polychlorinated bipbenyl (PCB, Aroclor 1260) crossed the placenta two to three times more readily than did DDE. Concentrations of PCB were significantly greater in litters with dead young than in litters where both young were born alive. The concentration of PCB in adult females plus their litters declined with increasing age of the female.

Jack Rabbit Pretest 2021E PT6 Photonic Doppler Velocimetry Data Volume 6 Section 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, M M; Strand, O T; Bosson, S T

The Jack Rabbit Pretest (PT) 2021E PT6 experiment was fired on April 1, 2008 at the Contained Firing Facility, Site 300, Lawrence Livermore National Laboratory. This experiment is part of an effort to determine the properties of LX-17 in a regime where corner-turning behavior and dead-zone formation are not well understood. Photonic Doppler Velocimetry (PDV) measured diagnostic plate velocities confirming the presence of a persistent LX-17 dead-zone formation and the resultant impulse gradient applied under the diagnostic plate. The Jack Rabbit Pretest 2021E PT6, 160 millimeter diameter experiment returned data on all eight PDV probes. The probes measured on themore » central axis and at 20, 30, 35, 45, 55, 65, 75 millimeters from the central axis. The experiment was shot at an ambient room temperature of 65 degrees Fahrenheit. The earliest PDV signal extinction was 54.2 microseconds at 30 millimeters. The latest PDV signal extinction time was 64.5 microseconds at the central axis. The measured velocity ranged from meters per second to thousands of meters per second. First detonation wave induced jump-off was measured at 55 millimeters at 14.1 microseconds. The PDV data provided an unambiguous indication of dead-zone formation and an impulse gradient applied to the diagnostic plate. The central axis had a last measured velocity of 1860 meters per second. At 55 millimeters the last measured velocity was 2408 meters per second. The low-to-high velocity ratio was 0.77. Velocity data was integrated to compute diagnostic plate cross section profiles. Velocity data was differentiated to compute a peak pressure under the diagnostic plate at the central axis of 227 kilobars at 20.1 microseconds, indicating a late time chemical reaction in the LX-17 dead-zone. Substantial motion (>1 m/s) of the diagnostic plate over the dead-zone is followed by detonation region motion within approximately 1.7 microseconds.« less

The death assemblage as a marker for habitat and an indicator of climate change: Georges Bank, surfclams and ocean quahogs

NASA Astrophysics Data System (ADS)

Powell, Eric N.; Kuykendall, Kelsey M.; Moreno, Paula

2017-06-01

A comprehensive dataset for the Georges Bank region is used to directly compare the distribution of the death assemblage and the living community at large spatial scales and to assess the application of the death assemblage in tracking changes in species' distributional pattern as a consequence of climate change. Focus is placed on the biomass-dominant clam species of the northwest Atlantic continental shelf: the surfclam Spisula solidissima and the ocean quahog Arctica islandica, for which extensive datasets exist on the distributions of the living population and the death assemblage. For both surfclams and ocean quahogs, the distribution of dead shells, in the main, tracked the distribution of live animals relatively closely. Thus, for both species, the presence of dead shells was a positive indicator of present, recent, or past occupation by live animals. Shell dispersion within habitat was greater for surfclams than for ocean quahogs either due to spatial time averaging, animals not living in all habitable areas all of the time, or parautochthonous redistribution of shell. The regional distribution of dead shell differed from the distribution of live animals, for both species, in a systematic way indicative of range shifts due to climate change. In each case the differential distribution was consistent with warming of the northwest Atlantic. Present-day overlap of live surfclams with live ocean quahogs was consistent with the expectation that the surfclam's range is shifting into deeper water in response to the recent warming trend. The presence of locations devoid of dead shells where live surfclams nevertheless were collected measures the recentness of this event. The presence of dead ocean quahog shells at shallower depths than live ocean quahogs offers good evidence that a range shift has occurred in the past, but prior to the initiation of routine surveys in 1980. Possibly, this range shift tracks initial colonization at the end of the Little Ice Age.

Digital computing cardiotachometer

NASA Technical Reports Server (NTRS)

Smith, H. E.; Rasquin, J. R.; Taylor, R. A. (Inventor)

1973-01-01

A tachometer is described which instantaneously measures heart rate. During the two intervals between three succeeding heart beats, the electronic system: (1) measures the interval by counting cycles from a fixed frequency source occurring between the two beats; and (2) computes heat rate during the interval between the next two beats by counting the number of times that the interval count must be counted to zero in order to equal a total count of sixty times (to convert to beats per minute) the frequency of the fixed frequency source.

Detector Development for the abBA Experiment.

PubMed

Seo, P-N; Bowman, J D; Mitchell, G S; Penttila, S I; Wilburn, W S

2005-01-01

We have developed a new type of field-expansion spectrometer to measure the neutron beta decay correlations (a, b, B, and A). A precision measurement of these correlations places stringent requirements on charged particle detectors. The design employs large area segmented silicon detectors to detect both protons and electrons in coincidence. Other requirements include good energy resolution (< 5 keV), a thin dead layer to allow observation of 30-keV protons, fast timing resolution (~1 ns) to reconstruct electron-backscattering events, and nearly unity efficiency. We report results of testing commercially available surface-barrier silicon detectors for energy resolution and timing performance, and measurement of the dead-layer thickness of ion-implanted silicon detectors with a 3.2 MeV alpha source.

Proceedings of the symposium on the ecology and management of dead wood in western forests

Treesearch

William F. Laudenslayer; Patrick J. Shea; Bradley E. Valentine; C. Phillip Weatherspoon; Thomas E. Lisle

2002-01-01

Dead trees, both snags (standing dead trees) and logs (downed dead trees), are critical elements of healthy and productive forests. The “Symposium on the Ecology and Management of Dead Wood in Western Forests” was convened to bring together forest researchers and managers to share the current state of knowledge relative to the values and interactions of dead wood to...

Adaptive engine injection for emissions reduction

DOEpatents

Reitz, Rolf D. : Sun, Yong

2008-12-16

NOx and soot emissions from internal combustion engines, and in particular compression ignition (diesel) engines, are reduced by varying fuel injection timing, fuel injection pressure, and injected fuel volume between low and greater engine loads. At low loads, fuel is injected during one or more low-pressure injections occurring at low injection pressures between the start of the intake stroke and approximately 40 degrees before top dead center during the compression stroke. At higher loads, similar injections are used early in each combustion cycle, in addition to later injections which preferably occur between about 90 degrees before top dead center during the compression stroke, and about 90 degrees after top dead center during the expansion stroke (and which most preferably begin at or closely adjacent the end of the compression stroke). These later injections have higher injection pressure, and also lower injected fuel volume, than the earlier injections.

WHY ARE PULSAR PLANETS RARE?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, Rebecca G.; Livio, Mario; Palaniswamy, Divya

Pulsar timing observations have revealed planets around only a few pulsars. We suggest that the rarity of these planets is due mainly to two effects. First, we show that the most likely formation mechanism requires the destruction of a companion star. Only pulsars with a suitable companion (with an extreme mass ratio) are able to form planets. Second, while a dead zone (a region of low turbulence) in the disk is generally thought to be essential for planet formation, it is most probably rare in disks around pulsars, because of the irradiation from the pulsar. The irradiation strongly heats themore » inner parts of the disk, thus pushing the inner boundary of the dead zone out. We suggest that the rarity of pulsar planets can be explained by the low probability for these two requirements to be satisfied: a very low-mass companion and a dead zone.« less

Optimization of a Viability PCR Method for the Detection of Listeria monocytogenes in Food Samples.

PubMed

Agustí, Gemma; Fittipaldi, Mariana; Codony, Francesc

2018-06-01

Rapid detection of Listeria and other microbial pathogens in food is an essential part of quality control and it is critical for ensuring the safety of consumers. Culture-based methods for detecting foodborne pathogens are time-consuming, laborious and cannot detect viable but non-culturable microorganism, whereas viability PCR methodology provides quick results; it is able to detect viable but non-culturable cells, and allows for easier handling of large amount of samples. Although the most critical point to use viability PCR technique is achieving the complete exclusion of dead cell amplification signals, many improvements are being introduced to overcome this. In the present work, the yield of dead cell DNA neutralization was enhanced by incorporating two new sample treatment strategies: tube change combined with a double light treatment. This procedure was successfully tested using artificially contaminated food samples, showing improved neutralization of dead cell DNA.

All Eyes on Egypt: Islam and the Medical Use of Dead Bodies Amidst Cairo's Political Unrest.

PubMed

Hamdy, Sherine

2016-01-01

Using dead bodies for medical purposes has long been considered taboo in Egypt. Public health campaigns, physicians' pleas, and the urgings of religious scholars all failed to alter public opinion regarding the donation of dead bodies either for instructional material or for therapeutic treatments. Yet in 2011, amid revolutionary turmoil in Egypt, a campaign was launched for people to donate their eyes upon death; this time, people readily signed up to be donors. Focusing on mass eye trauma that occurred in Egypt amid the political uprisings of 2011, I raise questions about when and why Islam can explain people's attitudes and behaviors, particularly toward death and medicine. The case of mass eye trauma in Egypt and citizens' reformulations of questions once jealously controlled by state-aligned doctors, politicians, and religious scholars unsettles the boundaries between 'religion' and 'secularism' in medical practice. [Formula: see text].

The Prevalence and Control of Bacillus and Related Spore-Forming Bacteria in the Dairy Industry.

PubMed

Gopal, Nidhi; Hill, Colin; Ross, Paul R; Beresford, Tom P; Fenelon, Mark A; Cotter, Paul D

2015-01-01

Milk produced in udder cells is sterile but due to its high nutrient content, it can be a good growth substrate for contaminating bacteria. The quality of milk is monitored via somatic cell counts and total bacterial counts, with prescribed regulatory limits to ensure quality and safety. Bacterial contaminants can cause disease, or spoilage of milk and its secondary products. Aerobic spore-forming bacteria, such as those from the genera Sporosarcina, Paenisporosarcina, Brevibacillus, Paenibacillus, Geobacillus and Bacillus, are a particular concern in this regard as they are able to survive industrial pasteurization and form biofilms within pipes and stainless steel equipment. These single or multiple-species biofilms become a reservoir of spoilage microorganisms and a cycle of contamination can be initiated. Indeed, previous studies have highlighted that these microorganisms are highly prevalent in dead ends, corners, cracks, crevices, gaskets, valves and the joints of stainless steel equipment used in the dairy manufacturing plants. Hence, adequate monitoring and control measures are essential to prevent spoilage and ensure consumer safety. Common controlling approaches include specific cleaning-in-place processes, chemical and biological biocides and other novel methods. In this review, we highlight the problems caused by these microorganisms, and discuss issues relating to their prevalence, monitoring thereof and control with respect to the dairy industry.

The Prevalence and Control of Bacillus and Related Spore-Forming Bacteria in the Dairy Industry

PubMed Central

Gopal, Nidhi; Hill, Colin; Ross, Paul R.; Beresford, Tom P.; Fenelon, Mark A.; Cotter, Paul D.

2015-01-01

Milk produced in udder cells is sterile but due to its high nutrient content, it can be a good growth substrate for contaminating bacteria. The quality of milk is monitored via somatic cell counts and total bacterial counts, with prescribed regulatory limits to ensure quality and safety. Bacterial contaminants can cause disease, or spoilage of milk and its secondary products. Aerobic spore-forming bacteria, such as those from the genera Sporosarcina, Paenisporosarcina, Brevibacillus, Paenibacillus, Geobacillus and Bacillus, are a particular concern in this regard as they are able to survive industrial pasteurization and form biofilms within pipes and stainless steel equipment. These single or multiple-species biofilms become a reservoir of spoilage microorganisms and a cycle of contamination can be initiated. Indeed, previous studies have highlighted that these microorganisms are highly prevalent in dead ends, corners, cracks, crevices, gaskets, valves and the joints of stainless steel equipment used in the dairy manufacturing plants. Hence, adequate monitoring and control measures are essential to prevent spoilage and ensure consumer safety. Common controlling approaches include specific cleaning-in-place processes, chemical and biological biocides and other novel methods. In this review, we highlight the problems caused by these microorganisms, and discuss issues relating to their prevalence, monitoring thereof and control with respect to the dairy industry. PMID:26733963

A Smartphone Step Counter Using IMU and Magnetometer for Navigation and Health Monitoring Applications

PubMed Central

Khedr, Maan; El-Sheimy, Nasser

2017-01-01

The growing market of smart devices make them appealing for various applications. Motion tracking can be achieved using such devices, and is important for various applications such as navigation, search and rescue, health monitoring, and quality of life-style assessment. Step detection is a crucial task that affects the accuracy and quality of such applications. In this paper, a new step detection technique is proposed, which can be used for step counting and activity monitoring for health applications as well as part of a Pedestrian Dead Reckoning (PDR) system. Inertial and Magnetic sensors measurements are analyzed and fused for detecting steps under varying step modes and device pose combinations using a free-moving handheld device (smartphone). Unlike most of the state of the art research in the field, the proposed technique does not require a classifier, and adaptively tunes the filters and thresholds used without the need for presets while accomplishing the task in a real-time operation manner. Testing shows that the proposed technique successfully detects steps under varying motion speeds and device use cases with an average performance of 99.6%, and outperforms some of the state of the art techniques that rely on classifiers and commercial wristband products. PMID:29117143

Dead Sea deep cores: A window into past climate and seismicity

NASA Astrophysics Data System (ADS)

Stein, Mordechai; Ben-Avraham, Zvi; Goldstein, Steven L.

2011-12-01

The area surrounding the Dead Sea was the locus of humankind's migration out of Africa and thus has been the home of peoples since the Stone Age. For this reason, understanding the climate and tectonic history of the region provides valuable insight into archaeology and studies of human history and helps to gain a better picture of future climate and tectonic scenarios. The deposits at the bottom of the Dead Sea are a geological archive of the environmental conditions (e.g., rains, floods, dust storms, droughts) during ice ages and warm ages, as well as of seismic activity in this key region. An International Continental Scientific Drilling Program (ICDP) deep drilling project was performed in the Dead Sea between November 2010 and March 2011. The project was funded by the ICDP and agencies in Israel, Germany, Japan, Norway, Switzerland, and the United States. Drilling was conducted using the new Large Lake Drilling Facility (Figure 1), a barge with a drilling rig run by DOSECC, Inc. (Drilling, Observation and Sampling of the Earth's Continental Crust), a nonprofit corporation dedicated to advancing scientific drilling worldwide. The main purpose of the project was to recover a long, continuous core to provide a high resolution record of the paleoclimate, paleoenvironment, paleoseismicity, and paleomagnetism of the Dead Sea Basin. With this, scientists are beginning to piece together a record of the climate and seismic history of the Middle East during the past several hundred thousand years in millennial to decadal to annual time resolution.

Effects of acid and metal solutions on seedling foliage of two western conifers. Forest Service research note

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobs, J.; Weaver, T.; Cole, D.M.

1994-11-01

A greenhouse study tested the effects of three acids and five metals on foliage of lodgepole pine (Pinus contorta var. latifolia) and Douglas-fir (Pseudotsugs menziesii) seedlings. The seedlings were treated with a single immersion of foliage into solutions of three acids (HCL, H2S04, and HN3) and five metal chlorides (ZnC12, CdC12, HgC12, CuC12, and PbC12) each at five different concentration levels. Injury to the foliage was recorded after 5 weeks by counting needles that were chlorotic (yellow) or dead. Statistically significant (p < 0.05) effects were observed for both acids and metals. The effects of metals were far greater thanmore » the effects of acids for both species.« less

46 CFR 171.117 - Dead covers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Dead covers. 171.117 Section 171.117 Shipping COAST... Dead covers. (a) Except as provided in paragraph (b) of this section, each port light with the sill located below the margin line must have a hinged, inside dead cover. (b) The dead cover on a port light...

46 CFR 171.117 - Dead covers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Dead covers. 171.117 Section 171.117 Shipping COAST... Dead covers. (a) Except as provided in paragraph (b) of this section, each port light with the sill located below the margin line must have a hinged, inside dead cover. (b) The dead cover on a port light...

46 CFR 171.117 - Dead covers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Dead covers. 171.117 Section 171.117 Shipping COAST... Dead covers. (a) Except as provided in paragraph (b) of this section, each port light with the sill located below the margin line must have a hinged, inside dead cover. (b) The dead cover on a port light...

46 CFR 171.117 - Dead covers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Dead covers. 171.117 Section 171.117 Shipping COAST... Dead covers. (a) Except as provided in paragraph (b) of this section, each port light with the sill located below the margin line must have a hinged, inside dead cover. (b) The dead cover on a port light...

46 CFR 171.117 - Dead covers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Dead covers. 171.117 Section 171.117 Shipping COAST... Dead covers. (a) Except as provided in paragraph (b) of this section, each port light with the sill located below the margin line must have a hinged, inside dead cover. (b) The dead cover on a port light...

Whose body is it anyway?: trading the dead poor, coroner's disputes, and the business of anatomy at Oxford University, 1885-1929.

PubMed

Hurren, Elizabeth T

2008-01-01

This article examines the application of the Anatomy Act (1832) at Oxford University, circa 1885-1929. For the first time it retraces the economy of supply in dead bodies, sold by various black-market intermediaries and welfare agencies, transported on the railway to Oxford. Both pauper cadavers and body parts were used to train doctors in human anatomy at a time when student demand always exceeded the economy of supply. An added problem was that the trade in dead bodies was disrupted by a city coroner for Oxford in a bid to improve his professional standing. Disputes about medico-legal authority over the pauper corpse meant that the Anatomy Department failed to convince the local poor in the city center to sell their loved ones' remains for dissection on a regular basis. Adverse publicity was a constant financial headache for anatomists. Consistently, they had to pay higher prices for cadavers than their competitors did. Often bodies were purchased in surrounding Midlands towns. This context explains why the Anatomy Department at Oxford failed at the business of anatomy in the late Victorian and early Edwardian eras.

PMA-PhyloChip DNA Microarray to Elucidate Viable Microbial Community Structure

NASA Technical Reports Server (NTRS)

Venkateswaran, Kasthuri J.; Stam, Christina N.; Andersen, Gary L.; DeSantis, Todd

2011-01-01

Since the Viking missions in the mid-1970s, traditional culture-based methods have been used for microbial enumeration by various NASA programs. Viable microbes are of particular concern for spacecraft cleanliness, for forward contamination of extraterrestrial bodies (proliferation of microbes), and for crew health/safety (viable pathogenic microbes). However, a "true" estimation of viable microbial population and differentiation from their dead cells using the most sensitive molecular methods is a challenge, because of the stability of DNA from dead cells. The goal of this research is to evaluate a rapid and sensitive microbial detection concept that will selectively estimate viable microbes. Nucleic acid amplification approaches such as the polymerase chain reaction (PCR) have shown promise for reducing time to detection for a wide range of applications. The proposed method is based on the use of a fluorescent DNA intercalating agent, propidium monoazide (PMA), which can only penetrate the membrane of dead cells. The PMA-quenched reaction mixtures can be screened, where only the DNA from live cells will be available for subsequent PCR reaction and microarray detection, and be identified as part of the viable microbial community. An additional advantage of the proposed rapid method is that it will detect viable microbes and differentiate from dead cells in only a few hours, as opposed to less comprehensive culture-based assays, which take days to complete. This novel combination approach is called the PMA-Microarray method. DNA intercalating agents such as PMA have previously been used to selectively distinguish between viable and dead bacterial cells. Once in the cell, the dye intercalates with the DNA and, upon photolysis under visible light, produces stable DNA adducts. DNA cross-linked in this way is unavailable for PCR. Environmental samples suspected of containing a mixture of live and dead microbial cells/spores will be treated with PMA, and then incubated in the dark. Thereafter, the sample is exposed to visible light for five minutes, so that the DNA from dead cells will be cross-linked. Following this PMA treatment step, the sample is concentrated by centrifugation and washed (to remove excessive PMA) before DNA is extracted. The 16S rRNA gene fragments will be amplified by PCR to screen the total microbial community using PhyloChip DNA microarray analysis. This approach will detect only the viable microbial community since the PMA intercalated DNA from dead cells would be unavailable for PCR amplification. The total detection time including PCR reaction for low biomass samples will be a few hours. Numerous markets may use this technology. The food industry uses spore detection to validate new alternative food processing technologies, sterility, and quality. Pharmaceutical and medical equipment companies also detect spores as a marker for sterility. This system can be used for validating sterilization processes, water treatment systems, and in various public health and homeland security applications.

The EIGER detector for low-energy electron microscopy and photoemission electron microscopy.

PubMed

Tinti, G; Marchetto, H; Vaz, C A F; Kleibert, A; Andrä, M; Barten, R; Bergamaschi, A; Brückner, M; Cartier, S; Dinapoli, R; Franz, T; Fröjdh, E; Greiffenberg, D; Lopez-Cuenca, C; Mezza, D; Mozzanica, A; Nolting, F; Ramilli, M; Redford, S; Ruat, M; Ruder, Ch; Schädler, L; Schmidt, Th; Schmitt, B; Schütz, F; Shi, X; Thattil, D; Vetter, S; Zhang, J

2017-09-01

EIGER is a single-photon-counting hybrid pixel detector developed at the Paul Scherrer Institut, Switzerland. It is designed for applications at synchrotron light sources with photon energies above 5 keV. Features of EIGER include a small pixel size (75 µm × 75 µm), a high frame rate (up to 23 kHz), a small dead-time between frames (down to 3 µs) and a dynamic range up to 32-bit. In this article, the use of EIGER as a detector for electrons in low-energy electron microscopy (LEEM) and photoemission electron microscopy (PEEM) is reported. It is demonstrated that, with only a minimal modification to the sensitive part of the detector, EIGER is able to detect electrons emitted or reflected by the sample and accelerated to 8-20 keV. The imaging capabilities are shown to be superior to the standard microchannel plate detector for these types of applications. This is due to the much higher signal-to-noise ratio, better homogeneity and improved dynamic range. In addition, the operation of the EIGER detector is not affected by radiation damage from electrons in the present energy range and guarantees more stable performance over time. To benchmark the detector capabilities, LEEM experiments are performed on selected surfaces and the magnetic and electronic properties of individual iron nanoparticles with sizes ranging from 8 to 22 nm are detected using the PEEM endstation at the Surface/Interface Microscopy (SIM) beamline of the Swiss Light Source.

Entropy is more resistant to artifacts than bispectral index in brain-dead organ donors.

PubMed

Wennervirta, Johanna; Salmi, Tapani; Hynynen, Markku; Yli-Hankala, Arvi; Koivusalo, Anna-Maria; Van Gils, Mark; Pöyhiä, Reino; Vakkuri, Anne

2007-01-01

To evaluate the usefulness of entropy and the bispectral index (BIS) in brain-dead subjects. A prospective, open, nonselective, observational study in the university hospital. 16 brain-dead organ donors. Time-domain electroencephalography (EEG), spectral entropy of the EEG, and BIS were recorded during solid organ harvest. State entropy differed significantly from 0 (isoelectric EEG) 28%, response entropy 29%, and BIS 68% of the total recorded time. The median values during the operation were state entropy 0.0, response entropy 0.0, and BIS 3.0. In four of 16 organ donors studied the EEG was not isoelectric, and nonreactive rhythmic activity was noted in time-domain EEG. After excluding the results from subjects with persistent residual EEG activity state entropy, response entropy, and BIS values differed from zero 17%, 18%, and 62% of the recorded time, respectively. Median values were 0.0, 0.0, and 2.0 for state entropy, response entropy, and BIS, respectively. The highest index values in entropy and BIS monitoring were recorded without neuromuscular blockade. The main sources of artifacts were electrocauterization, 50-Hz artifact, handling of the donor, ballistocardiography, electromyography, and electrocardiography. Both entropy and BIS showed nonzero values due to artifacts after brain death diagnosis. BIS was more liable to artifacts than entropy. Neither of these indices are diagnostic tools, and care should be taken when interpreting EEG and EEG-derived indices in the evaluation of brain death.

Evaluation of automated time-lapse microscopy for assessment of in vitro activity of antibiotics.

PubMed

Ungphakorn, Wanchana; Malmberg, Christer; Lagerbäck, Pernilla; Cars, Otto; Nielsen, Elisabet I; Tängdén, Thomas

2017-01-01

This study aimed to evaluate the potential of a new time-lapse microscopy based method (oCelloScope) to efficiently assess the in vitro antibacterial effects of antibiotics. Two E. coli and one P. aeruginosa strain were exposed to ciprofloxacin, colistin, ertapenem and meropenem in 24-h experiments. Background corrected absorption (BCA) derived from the oCelloScope was used to detect bacterial growth. The data obtained with the oCelloScope were compared with those of the automated Bioscreen C method and standard time-kill experiments and a good agreement in results was observed during 6-24h of experiments. Viable counts obtained at 1, 4, 6 and 24h during oCelloScope and Bioscreen C experiments were well correlated with the corresponding BCA and optical density (OD) data. Initial antibacterial effects during the first 6h of experiments were difficult to detect with the automated methods due to their high detection limits (approximately 10 5 CFU/mL for oCelloScope and 10 7 CFU/mL for Bioscreen C), the inability to distinguish between live and dead bacteria and early morphological changes of bacteria during exposure to ciprofloxacin, ertapenem and meropenem. Regrowth was more frequently detected in time-kill experiments, possibly related to the larger working volume with an increased risk of pre-existing or emerging resistance. In comparison with Bioscreen C, the oCelloScope provided additional information on bacterial growth dynamics in the range of 10 5 to 10 7 CFU/mL and morphological features. In conclusion, the oCelloScope would be suitable for detection of in vitro effects of antibiotics, especially when a large number of regimens need to be tested. Copyright © 2016 Elsevier B.V. All rights reserved.

Patterns of mortality in a montane mixed-conifer forest in San Diego County, California.

PubMed

Freeman, Mary Pyott; Stow, Douglas A; An, Li

2017-10-01

We examine spatial patterns of conifer tree mortality and their changes over time for the montane mixed-conifer forests of San Diego County. These forest areas have recently experienced extensive tree mortality due to multiple factors. A spatial contextual image processing approach was utilized with high spatial resolution digital airborne imagery to map dead trees for the years 1997, 2000, 2002, and 2005 for three study areas: Palomar, Volcan, and Laguna mountains. Plot-based fieldwork was conducted to further assess mortality patterns. Mean mortality remained static from 1997 to 2002 (4, 2.2, and 4.2 trees/ha for Palomar, Volcan, and Laguna) and then increased by 2005 to 10.3, 9.7, and 5.2 trees/ha, respectively. The increase in mortality between 2002 and 2005 represents the temporal pattern of a discrete disturbance event, attributable to the 2002-2003 drought. Dead trees are significantly clustered for all dates, based on spatial cluster analysis, indicating that they form distinct groups, as opposed to spatially random single dead trees. Other tests indicate no directional shift or spread of mortality over time, but rather an increase in density. While general temporal and spatial mortality processes are uniform across all study areas, the plot-based species and quantity distribution of mortality, and diameter distributions of dead vs. living trees, vary by study area. The results of this study improve our understanding of stand- to landscape-level forest structure and dynamics, particularly by examining them from the multiple perspectives of field and remotely sensed data. © 2017 by the Ecological Society of America.

The "New Deadly Quartet" for cardiovascular disease in the 21st century: obesity, metabolic syndrome, inflammation and climate change: how does statin therapy fit into this equation?

PubMed

Clearfield, Michael; Pearce, Melissa; Nibbe, Yasmin; Crotty, David; Wagner, Alesia

2014-01-01

Despite population-based improvements in cardiovascular risk factors, such as blood pressure, cholesterol and smoking, cardiovascular disease still remains the number-one cause of mortality in the United States. In 1989, Kaplan coined the term "Deadly Quartet" to represent a combination of risk factors that included upper body obesity, glucose intolerance, hypertriglyceridemia and hypertension [Kaplan in Arch Int Med 7:1514-1520, 1989]. In 2002, the third report of the National Cholesterol Education Program Adult Treatment Panel (NCEP-ATP III) essentially added low HDL-C criteria and renamed this the "metabolic syndrome." [The National Cholesterol Education Program (NCEP) in JAMA 285:2486-2497, 2001] However, often forgotten was that a pro-inflammatory state and pro-thrombotic state were also considered components of the syndrome, albeit the panel did not find enough evidence at the time to recommend routine screening for these risk factors [The National Cholesterol Education Program (NCEP) in JAMA 285:2486-2497, 2001]. Now over a decade later, it may be time to reconsider this deadly quartet by reevaluating the roles of obesity and subclinical inflammation as they relate to the metabolic syndrome. To complete this new quartet, the addition of increased exposure to elevated levels of particulate matter in the atmosphere may help elucidate why this cardiovascular pandemic continues, despite our concerted efforts. In this article, we will summarize the evidence, focusing on how statin therapy may further impact this new version of the "deadly quartet".

AUTOMATIC COUNTING APPARATUS

DOEpatents

Howell, W.D.

1957-08-20

An apparatus for automatically recording the results of counting operations on trains of electrical pulses is described. The disadvantages of prior devices utilizing the two common methods of obtaining the count rate are overcome by this apparatus; in the case of time controlled operation, the disclosed system automatically records amy information stored by the scaler but not transferred to the printer at the end of the predetermined time controlled operations and, in the case of count controlled operation, provision is made to prevent a weak sample from occupying the apparatus for an excessively long period of time.

Bayesian analysis of energy and count rate data for detection of low count rate radioactive sources.

PubMed

Klumpp, John; Brandl, Alexander

2015-03-01

A particle counting and detection system is proposed that searches for elevated count rates in multiple energy regions simultaneously. The system analyzes time-interval data (e.g., time between counts), as this was shown to be a more sensitive technique for detecting low count rate sources compared to analyzing counts per unit interval (Luo et al. 2013). Two distinct versions of the detection system are developed. The first is intended for situations in which the sample is fixed and can be measured for an unlimited amount of time. The second version is intended to detect sources that are physically moving relative to the detector, such as a truck moving past a fixed roadside detector or a waste storage facility under an airplane. In both cases, the detection system is expected to be active indefinitely; i.e., it is an online detection system. Both versions of the multi-energy detection systems are compared to their respective gross count rate detection systems in terms of Type I and Type II error rates and sensitivity.

Advanced readout methods for superheated emulsion detectors

NASA Astrophysics Data System (ADS)

d'Errico, F.; Di Fulvio, A.

2018-05-01

Superheated emulsions develop visible vapor bubbles when exposed to ionizing radiation. They consist in droplets of a metastable liquid, emulsified in an inert matrix. The formation of a bubble cavity is accompanied by sound waves. Evaporated bubbles also exhibit a lower refractive index, compared to the inert gel matrix. These two physical phenomena have been exploited to count the number of evaporated bubbles and thus measure the interacting radiation flux. Systems based on piezoelectric transducers have been traditionally used to acquire the acoustic (pressure) signals generated by bubble evaporation. Such systems can operate at ambient noise levels exceeding 100 dB; however, they are affected by a significant dead time (>10 ms). An optical readout technique relying on the scattering of light by neutron-induced bubbles has been recently improved in order to minimize measurement dead time and ambient noise sensitivity. Beams of infra-red light from light-emitting diode (LED) sources cross the active area of the detector and are deflected by evaporated bubbles. The scattered light correlates with bubble density. Planar photodiodes are affixed along the detector length in optimized positions, allowing the detection of scattered light from the bubbles and minimizing the detection of direct light from the LEDs. A low-noise signal-conditioning stage has been designed and realized to amplify the current induced in the photodiodes by scattered light and to subtract the background signal due to intrinsic scattering within the detector matrix. The proposed amplification architecture maximizes the measurement signal-to-noise ratio, yielding a readout uncertainty of 6% (±1 SD), with 1000 evaporated bubbles in a detector active volume of 150 ml (6 cm detector diameter). In this work, we prove that the intensity of scattered light also relates to the bubble size, which can be controlled by applying an external pressure to the detector emulsion. This effect can be exploited during the readout procedure to minimize shadowing effects between bubbles, which become severe when the latter are several thousands. The detector we used in this work is based on superheated C-318 (octafluorocyclobutane), emulsified in 100 μm ± 10% (1 SD) diameter drops in an inert matrix of approximately 150 ml. The detector was operated at room temperature and ambient pressure.

Data processing for the Active Particle-induced X-ray Spectrometer and initial scientific results from Chang'e-3 mission

NASA Astrophysics Data System (ADS)

Fu, Xiao-Hui; Li, Chun-Lai; Zhang, Guang-Liang; Zou, Yong-Liao; Liu, Jian-Jun; Ren, Xin; Tan, Xu; Zhang, Xiao-Xia; Zuo, Wei; Wen, Wei-Bin; Peng, Wen-Xi; Cui, Xing-Zhu; Zhang, Cheng-Mo; Wang, Huan-Yu

2014-12-01

The Active Particle-induced X-ray Spectrometer (APXS) is an important payload mounted on the Yutu rover, which is part of the Chang'e-3 mission. The scientific objective of APXS is to perform in-situ analysis of the chemical composition of lunar soil and rock samples. The radioactive sources, 55Fe and 109Cd, decay and produce α-particles and X-rays. When X-rays and α-particles interact with atoms in the surface material, they knock electrons out of their orbits, which release energy by emitting X-rays that can be measured by a silicon drift detector (SDD). The elements and their concentrations can be determined by analyzing their peak energies and intensities. APXS has analyzed both the calibration target and lunar soil once during the first lunar day and again during the second lunar day. The total detection time lasted about 266 min and more than 2000 frames of data records have been acquired. APXS has three operating modes: calibration mode, distance sensing mode and detection mode. In detection mode, work distance can be calculated from the X-ray counting rate collected by SDD. Correction for the effect of temperature has been performed to convert the channel number for each spectrum to X-ray energy. Dead time correction is used to eliminate the systematic error in quantifying the activity of an X-ray pulse in a sample and derive the real count rate. We report APXS data and initial results during the first and second lunar days for the Yutu rover. In this study, we analyze the data from the calibration target and lunar soil on the first lunar day. Seven major elements, including Mg, Al, Si, K, Ca, Ti and Fe, have been identified. Comparing the peak areas and ratios of calibration basalt and lunar soil the landing site was found to be depleted in K, and have lower Mg and Al but higher Ca, Ti, and Fe. In the future, we will obtain the elemental concentrations of lunar soil at the Chang'e-3 landing site using APXS data.

45 CFR 46.206 - Research involving, after delivery, the placenta, the dead fetus or fetal material.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., the dead fetus or fetal material. 46.206 Section 46.206 Public Welfare DEPARTMENT OF HEALTH AND HUMAN... placenta, the dead fetus or fetal material. (a) Research involving, after delivery, the placenta; the dead fetus; macerated fetal material; or cells, tissue, or organs excised from a dead fetus, shall be...

45 CFR 46.206 - Research involving, after delivery, the placenta, the dead fetus or fetal material.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., the dead fetus or fetal material. 46.206 Section 46.206 Public Welfare DEPARTMENT OF HEALTH AND HUMAN... placenta, the dead fetus or fetal material. (a) Research involving, after delivery, the placenta; the dead fetus; macerated fetal material; or cells, tissue, or organs excised from a dead fetus, shall be...

45 CFR 46.206 - Research involving, after delivery, the placenta, the dead fetus or fetal material.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., the dead fetus or fetal material. 46.206 Section 46.206 Public Welfare DEPARTMENT OF HEALTH AND HUMAN... placenta, the dead fetus or fetal material. (a) Research involving, after delivery, the placenta; the dead fetus; macerated fetal material; or cells, tissue, or organs excised from a dead fetus, shall be...

45 CFR 46.206 - Research involving, after delivery, the placenta, the dead fetus or fetal material.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., the dead fetus or fetal material. 46.206 Section 46.206 Public Welfare Department of Health and Human... placenta, the dead fetus or fetal material. (a) Research involving, after delivery, the placenta; the dead fetus; macerated fetal material; or cells, tissue, or organs excised from a dead fetus, shall be...

45 CFR 46.206 - Research involving, after delivery, the placenta, the dead fetus or fetal material.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., the dead fetus or fetal material. 46.206 Section 46.206 Public Welfare DEPARTMENT OF HEALTH AND HUMAN... placenta, the dead fetus or fetal material. (a) Research involving, after delivery, the placenta; the dead fetus; macerated fetal material; or cells, tissue, or organs excised from a dead fetus, shall be...

More Dead than Dead: Perceptions of Persons in the Persistent Vegetative State

ERIC Educational Resources Information Center

Gray, Kurt; Knickman, T. Anne; Wegner, Daniel M.

2011-01-01

Patients in persistent vegetative state (PVS) may be biologically alive, but these experiments indicate that people see PVS as a state curiously more dead than dead. Experiment 1 found that PVS patients were perceived to have less mental capacity than the dead. Experiment 2 explained this effect as an outgrowth of afterlife beliefs, and the…

T1 weighted fat/water separated PROPELLER acquired with dual bandwidths.

PubMed

Rydén, Henric; Berglund, Johan; Norbeck, Ola; Avventi, Enrico; Skare, Stefan

2018-04-24

To describe a fat/water separated dual receiver bandwidth (rBW) spin echo PROPELLER sequence that eliminates the dead time associated with single rBW sequences. A nonuniform noise whitening by regularization of the fat/water inverse problem is proposed, to enable dual rBW reconstructions. Bipolar, flyback, and dual spin echo sequences were developed. All sequences acquire two echoes with different rBW without dead time. Chemical shift displacement was corrected by performing the fat/water separation in k-space, prior to gridding. The proposed sequences were compared to fat saturation, and single rBW sequences, in terms of SNR and CNR efficiency, using clinically relevant acquisition parameters. The impact of motion was investigated. Chemical shift correction greatly improved the image quality, especially at high resolution acquired with low rBW, and also improved motion estimates. SNR efficiency of the dual spin echo sequence was up to 20% higher than the single rBW acquisition, while CNR efficiency was 50% higher for the bipolar acquisition. Noise whitening was deemed necessary for all dual rBW acquisitions, rendering high image quality with strong and homogenous fat suppression. Dual rBW sequences eliminate the dead time present in single rBW sequences, which improves SNR efficiency. In combination with the proposed regularization, this enables highly efficient T1-weighted PROPELLER images without chemical shift displacement. © 2018 International Society for Magnetic Resonance in Medicine.

9 CFR 82.4 - General provisions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... following articles may not be moved interstate from a quarantined area: (1) Dead birds and dead poultry...) Dressed carcasses of birds and poultry, and other dead birds and dead poultry, including any parts of the...

9 CFR 82.4 - General provisions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... following articles may not be moved interstate from a quarantined area: (1) Dead birds and dead poultry...) Dressed carcasses of birds and poultry, and other dead birds and dead poultry, including any parts of the...

9 CFR 82.4 - General provisions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... following articles may not be moved interstate from a quarantined area: (1) Dead birds and dead poultry...) Dressed carcasses of birds and poultry, and other dead birds and dead poultry, including any parts of the...