Improvements in purification of silver nanowires by decantation and fabrication of flexible transparent electrodes. Application to capacitive touch sensors.

PubMed

Mayousse, Céline; Celle, Caroline; Moreau, Eléonore; Mainguet, Jean-François; Carella, Alexandre; Simonato, Jean-Pierre

2013-05-31

Transparent flexible electrodes made of metallic nanowires, and in particular silver nanowires (AgNWs), appear as an extremely promising alternative to transparent conductive oxides for future optoelectronic devices. Though significant progresses have been made the last few years, there is still some room for improvement regarding the synthesis of high quality silver nanowire solutions and fabrication process of high performance electrodes. We show that the commonly used purification process can be greatly simplified through decantation. Using this process it is possible to fabricate flexible electrodes by spray coating with sheet resistance lower than 25 Ω sq⁻¹ at 90% transparency in the visible spectrum. These electrodes were used to fabricate an operative transparent flexible touch screen. To our knowledge this is the first reported AgNW based touch sensor relying on capacitive technology.

Recovery and reuse of cellulase catalyst in an exzymatic cellulose hydrolysis process

DOEpatents

Woodward, Jonathan

1989-01-01

A process for recovering cellulase from the hydrolysis of cellulose, and reusing it in subsequent hydrolyois procedures. The process utilizes a commercial adsorbent that efficiently removes cellulase from reaction products which can be easily removed by simple decantation.

Ultra scale-down device to predict dewatering levels of solids recovered in a continuous scroll decanter centrifuge.

PubMed

Lopes, A G; Keshavarz-Moore, E

2013-01-01

During centrifugation operation, the major challenge in the recovery of extracellular proteins is the removal of the maximum liquid entrapped within the spaces between the settled solids-dewatering level. The ability of the scroll decanter centrifuge (SDC) to process continuously large amounts of feed material with high concentration of solids without the need for resuspension of feeds, and also to achieve relatively high dewatering, could be of great benefit for future use in the biopharmaceutical industry. However, for reliable prediction of dewatering in such a centrifuge, tests using the same kind of equipment at pilot-scale are required, which are time consuming and costly. To alleviate the need of pilot-scale trials, a novel USD device, with reduced amounts of feed (2 mL) and to be used in the laboratory, was developed to predict the dewatering levels of a SDC. To verify USD device, dewatering levels achieved were plotted against equivalent compression (Gtcomp ) and decanting (Gtdec ) times, obtained from scroll rates and feed flow rates operated at pilot-scale, respectively. The USD device was able to successfully match dewatering trends of the pilot-scale as a function of both Gtcomp and Gtdec , particularly for high cell density feeds, hence accounting for all key variables that influenced dewatering in a SDC. In addition, it accurately mimicked the maximum dewatering performance of the pilot-scale equipment. Therefore the USD device has the potential to be a useful tool at early stages of process development to gather performance data in the laboratory thus minimizing lengthy and costly runs with pilot-scale SDC. © 2013 American Institute of Chemical Engineers.

Enhancing soil infiltration reduces gaseous emissions and improves N uptake from applied dairy slurry.

PubMed

Bhandral, R; Bittman, S; Kowalenko, G; Buckley, K; Chantigny, M H; Hunt, D E; Bounaix, F; Friesen, A

2009-01-01

Rapid infiltration of liquid manure into the soil reduces emissions of ammonia (NH(3)) into the atmosphere. This study was undertaken to assess the effects of two low-cost methods of assisting infiltration of applied dairy slurry on emissions of NH(3), nitrous oxide (N(2)O), and on crop N uptake. The two methods were removing of solids by settling-decantation to make the manure less viscous and mechanically aerating the soil. Ammonia emissions were measured with wind tunnels as percentage of applied total ammoniacal nitrogen (TAN) while emissions of N(2)O were measured with vented chambers. Mechanically aerating the soil before manure application significantly reduced emissions of NH(3) relative to the nonaerated soil in spring (38.6 to 20.3% of applied TAN), summer (41.1 to 26.4% of applied TAN) and fall (27.7 to 13.6% of applied TAN) trials. Decantation of manure had no effect on NH(3) emissions in spring, tended to increase emissions in summer and significantly decreased emissions in fall (30.3 to 11.1% of applied TAN). Combining the two abatement techniques reduced NH(3) emission by 82% in fall, under cool weather conditions typical of manure spreading. The two abatement techniques generally did not significantly affect N(2)O emissions. Uptake of applied N by Italian ryegrass (Lolium multiflorum Lam.) was generally significantly greater with decanted than from whole manure but the effect of aeration was generally small and not significant. The study shows that low cost methods that assist manure infiltration into the soil may be used to greatly reduce ammonia loss without increasing N(2)O emissions, but efficacy of abatement methods is affected by weather conditions.

Evolution of efficient methods to sample lead sources, such as house dust and hand dust, in the homes of children

DOE Office of Scientific and Technical Information (OSTI.GOV)

Que Hee, S.S.; Peace, B.; Clark, C.S.

Efficient sampling methods to recover lead-containing house dust and hand dust have been evolved so that sufficient lead is collected for analysis and to ensure that correlational analyses linking these two parameters to blood lead are not dependent on the efficiency of sampling. Precise collection of loose house dust from a 1-unit area (484 cmS) with a Tygon or stainless steel sampling tube connected to a portable sampling pump (1.2 to 2.5 liters/min) required repetitive sampling (three times). The Tygon tube sampling technique for loose house dust <177 m in diameter was around 72% efficient with respect to dust weightmore » and lead collection. A representative house dust contained 81% of its total weight in this fraction. A single handwipe for applied loose hand dust was not acceptably efficient or precise, and at least three wipes were necessary to achieve recoveries of >80% of the lead applied. House dusts of different particle sizes <246 m adhered equally well to hands. Analysis of lead-containing material usually required at least three digestions/decantations using hot plate or microwave techniques to allow at least 90% of the lead to be recovered. It was recommended that other investigators validate their handwiping, house dust sampling, and digestion techniques to facilitate comparison of results across studies. The final methodology for the Cincinnati longitudinal study was three sampling passes for surface dust using a stainless steel sampling tube; three microwave digestion/decantations for analysis of dust and paint; and three wipes with handwipes with one digestion/decantation for the analysis of six handwipes together.« less

A case of Dipylidium caninum infection in a child from the southeastern Poland.

PubMed

Szwaja, Bogusława; Romański, Leszek; Zabczyk, Michał

2011-01-01

Dipylidium caninum is a common intestinal tapeworm of dogs, cats and foxes. However, it occasionally infects also humans. We present a case of D. caninum infection in a 2-year-old child living in the Subcarpathian province. The infection was asymptomatic in the first months. The symptoms of abdominal pains, sleep disorders, loss of appetite, hyperactivity and occasional slimy stools appeared later. Proglottids on the underwear, in water while bathing and mobile proglottids passed with the stool were also observed. Prior to appropriate diagnosis the child was treated with pyrantelum (Pyrantelum) and albendazolum (Zentel). However, proglottids were found again in the stool after a few days. We examined stool samples and perianal smears collected from the child and his family. The stool samples were tested by coproscopic methods. Direct methods (direct preparation in 0.9% sodium chloride and in Lugol's solution, Kato thick smear) and concentration methods (decantation with distilled water and Faust's zinc sulphate centrifugal flotation) were used. In the stool samples taken from the child, we observed D. caninum proglottids demonstrating lateral genital pores and many packets of eggs containing from one to a few, mostly 3 to 4 eggs. In the direct preparations in 0.9% sodium chloride and in Lugol's solution single packets with D. caninum eggs were detected. In decantation preparations many D. caninum egg packets were observed. It has to be reported that the child's mother was infected with Giardia intestinalis. Dipylidiasis in humans is a rarely encountered infection in Poland and the diagnosis may be difficult. For these reasons we reported clinical case presentation, diagnostics, treatment and epidemiology of D. caninum infection. We have shown that concentration methods such as decantation might be very helpful in the diagnosis of dipylidiasis.

Potential Functional Byproducts from Guava Purée Processing.

PubMed

Lim, Si Yi; Tham, Paik Yean; Lim, Hilary Yi Ler; Heng, Wooi Shin; Chang, Ying Ping

2018-05-10

The valorization of guava waste requires compositional and functional studies. We tested three byproducts of guava purée processing, namely refiner, siever, and decanter. We analyzed the chemical composition and quantified the prebiotic activity score and selected carbohydrates; we also determined the water holding (WHC), oil holding (OHC), cation exchange capacities, bile acid binding, and glucose dialysis retardation (GDR) of the solid fraction and the antioxidative and α-amylase inhibitory capacities (AIC) of the ethanolic extract. Refiner contained 7.7% lipid, 7.08% protein and a relatively high phytate content; it had a high prebiotic activity score and possessed the highest binding capacity with deoxycholic acid. Siever contained high levels of low molecular weight carbohydrates and total tannin but relatively low crude fiber and cellulose contents. It had the highest binding with chenodeoxycholic acid (74.8%), and exhibited the highest 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity. Decanter was rich in cellulose and had a high prebiotic activity score. The WHC and OHC values of decanter were within a narrow range and also exhibited the highest binding with cholic acid (86.6%), and the highest values of GDR and AIC. The refiner waste could be included in animal feed but requires further processing to reduce the high phytate levels. All three guava byproducts had the potential to be a source of antioxidant dietary fiber (DF), a finding that warrants further in vivo study. To differing extents, the guava byproducts exhibited useful physicochemical binding properties and so possessed the potential for health-promoting activity. These byproducts could also be upgraded to other marketable products so the manufacturers of processed guava might be able to develop their businesses sustainably by making better use of them. © 2018 Institute of Food Technologists®.

HIGH PERFORMANCE SIDE-STREAM NITRIFICATION OF MUNICIPAL BIOSOLIDS TREATMENT DECANTS

EPA Science Inventory

Nutrient (i.e. nitrogen) contamination of surface waters constitutes one of the most pervasive problems facing wastewater treatment works across the country. Nitrogen discharge to surface water occurs mostly in the form of ammonia which is identified as the most toxic nitrogen sp...

Ames Lab 101: Lanthanum Decanting

ScienceCinema

Riedemann, Trevor

2018-04-27

Ames Laboratory scientist Trevor Riedemann explains the process that allows Ames Laboratory to produce some of the purest lanthanum in the world. This and other high-purity rare-earth elements are used to create alloys used in various research projects and play a crucial role in the Planck satellite mission.

Recovery and reuse of cellulase catalyst in an enzymatic cellulose hydrolysis process

DOEpatents

Woodward, J.

1987-09-18

A process for recovering cellulase from the hydrolysis of cellulose, and reusing it in subsequent hydrolyois procedures. The process utilizes a commercial adsorbent that efficiently removes cellulase from reaction products which can be easily removed by simple decantation. 1 fig., 4 tabs.

40 CFR 61.131 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... circulation tank means any vessel that functions to store or contain flushing liquor that is separated from... that functions to condense benzene-containing vapors. Light-oil decanter means any vessel, tank, or other type of device in the light-oil recovery operation that functions to separate light oil from water...

40 CFR 61.131 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... circulation tank means any vessel that functions to store or contain flushing liquor that is separated from... that functions to condense benzene-containing vapors. Light-oil decanter means any vessel, tank, or other type of device in the light-oil recovery operation that functions to separate light oil from water...

40 CFR 61.131 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... circulation tank means any vessel that functions to store or contain flushing liquor that is separated from... that functions to condense benzene-containing vapors. Light-oil decanter means any vessel, tank, or other type of device in the light-oil recovery operation that functions to separate light oil from water...

Osage orange (Maclura pomifera L) seed oil poly(alpha-hydroxydibutylamine) triglycerides: Synthesis and characterization

USDA-ARS?s Scientific Manuscript database

Milled Osage orange seeds (Maclura pomifera (Raf.) Schneid) were Soxhlet extracted with hexane, and portions of the extract were treated with activated carbon before solvent removal. The crude oil was winterized and degummed by centrifugation at low temperature. Decantation of the centrifuge gave an...

27 CFR 31.232 - Wine bottling.

Code of Federal Regulations, 2010 CFR

2010-04-01

.... The decanting of wine by caterers or other retail dealers for table or room service, banquets, and... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Wine bottling. 31.232... OF THE TREASURY LIQUORS ALCOHOL BEVERAGE DEALERS Miscellaneous § 31.232 Wine bottling. Each person...

40 CFR 61.130 - Applicability, designation of sources, and delegation of authority.

Code of Federal Regulations, 2012 CFR

2012-07-01

... National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.130... each of the following sources at furnace and foundry coke by-product recovery plants: tar decanters... tanks, light-oil storage tanks, and excess ammonia-liquor storage tanks at furnace coke by-product...

40 CFR 61.130 - Applicability, designation of sources, and delegation of authority.

Code of Federal Regulations, 2013 CFR

2013-07-01

... National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.130... each of the following sources at furnace and foundry coke by-product recovery plants: tar decanters... tanks, light-oil storage tanks, and excess ammonia-liquor storage tanks at furnace coke by-product...

40 CFR 61.130 - Applicability, designation of sources, and delegation of authority.

Code of Federal Regulations, 2011 CFR

2011-07-01

... National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.130... each of the following sources at furnace and foundry coke by-product recovery plants: tar decanters... tanks, light-oil storage tanks, and excess ammonia-liquor storage tanks at furnace coke by-product...

40 CFR 61.130 - Applicability, designation of sources, and delegation of authority.

Code of Federal Regulations, 2014 CFR

2014-07-01

... National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.130... each of the following sources at furnace and foundry coke by-product recovery plants: tar decanters... tanks, light-oil storage tanks, and excess ammonia-liquor storage tanks at furnace coke by-product...

40 CFR 61.130 - Applicability, designation of sources, and delegation of authority.

Code of Federal Regulations, 2010 CFR

2010-07-01

... National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.130... each of the following sources at furnace and foundry coke by-product recovery plants: tar decanters... tanks, light-oil storage tanks, and excess ammonia-liquor storage tanks at furnace coke by-product...

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2011 CFR

2011-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2014 CFR

2014-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2012 CFR

2012-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

30 CFR 715.18 - Dams constructed of or impounding waste material.

Code of Federal Regulations, 2010 CFR

2010-07-01

... point on the embankment crest and the maximum water elevation shall be at least 3 feet to avoid... facility to be evacuated by spillways or decants of 90 percent of the volume of water stored during the..., existing storage capacity of impounding structures, any fires occurring in the material over the past year...

Assessing the Toxicity and Bioavailability of 2,4-Dinitroanisole in Acute and Sub-Chronic Exposures Using the Earthworm, Eisenia fetida

DTIC Science & Technology

2010-06-01

different methods, 2nd method chosen for final study: ► Coelomocytes collected in 2 ml Guaiacol Glyceryl Ether ( GGE ) solution, centrifuged, decanted...worm to GGE t= 2mins collect coelomocyte solution 1 row per worm/treatment, obtain measurements through spectrophotometer NRRT analysis 1) 2) BUILDING

Use of frit-disc crucibles for routine and exploratory solution growth of single crystalline samples

DOE PAGES

Canfield, Paul C.; Kong, Tai; Kaluarachchi, Udhara S.; ...

2016-01-05

Solution growth of single crystals from high temperature solutions often involves the separation of residual solution from the grown crystals. For many growths of intermetallic compounds, this separation has historically been achieved with the use of plugs of silica wool. Whereas this is generally efficient in a mechanical sense, it leads to a significant contamination of the decanted liquid with silica fibres. In this paper, we present a simple design for frit-disc alumina crucible sets that has made their use in the growth single crystals from high temperature solutions both simple and affordable. An alumina frit-disc allows for the cleanmore » separation of the residual liquid from the solid phase. This allows for the reuse of the decanted liquid, either for further growth of the same phase, or for subsequent growth of other, related phases. In this article, we provide examples of the growth of isotopically substituted TbCd 6 and icosahedral i-RCd quasicrystals, as well as the separation of (i) the closely related Bi 2Rh 3S 2 and Bi 2Rh 3.5S 2 phases and (ii) and PrZn 11 and PrZn 17.« less

La Meme Chose: How Mathematics Can Explain the Thinking of Children and the Thinking of Children Can Illuminate Mathematical Philosophy

ERIC Educational Resources Information Center

Cable, John

2014-01-01

This article offers a new interpretation of Piaget's decanting experiments, employing the mathematical notion of equivalence instead of conservation. Some reference is made to Piaget's theories and to his educational legacy, but the focus in on certain of the experiments. The key to the new analysis is the abstraction principle, which…

Polymeric Microelectronics.

DTIC Science & Technology

1981-06-01

Swelling Procedure For Crosslinked Gel 2A.1 Materials: Spectral grade hexane Petri dish with glass plate cover Planchette Balance Vacuum oven 2A.2...Uncrosslinked Material) To determine the amount of uncrosslinked material decant the dupernatant hexane into a weighed planchette . Wash the gel and...swelling flask or dish with hexane again and pour into planchette . Place the planchette and its contents into a vacuum oven at 350C until the contents

Dense Medium Ore Concentrates of Bois-Noirs; MINERAIS DES BOIS NOIRS CONCENTRES DE MILIEU DENSE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Bris, J.; Leduc, M.

1959-01-01

The chemical treatment of uranium concentrates of BoisNoirs ore obtained by heavy medium are discussed. The first part deals with sulfuric acid attack on the concentrate, and the second part with the separation of the solution from residues by filtration. A third part deals with this separation by decantation. The fourth part deals with the carbonation of the pickling solutions obtained. (auth)

Thermal decomposition and kinetic evaluation of decanted 2,4,6-trinitrotoluene (TNT) for reutilization as composite material

NASA Astrophysics Data System (ADS)

Ahmed, M. F.; Hussain, A.; Malik, A. Q.

2016-08-01

Use of energetic materials has long been considered for only military purposes. However, it is very recent that their practical applications in wide range of commercial fields such as mining, road building, under water blasting and rocket propulsion system have been considered. About 5mg of 2,4,6-trinitrotoluene (TNT) in serviceable (Svc) as well as unserviceable (Unsvc) form were used for their thermal decomposition and kinetic parameters investigation. Thermogravimetric/ differential thermal analysis (TG/DTA), X-ray diffraction (XRD) and Scanning electron microscope (SEM) were used to characterize two types of TNT. Arrhenius kinetic parameters like activation energy (E) and enthalpy (AH) of both TNT samples were determined using TG curves with the help of Horowitz and Metzger method. Simultaneously, thermal decomposition range was evaluated from DTA curves. Distinct diffraction peaks showing crystalline nature were obtained from XRD analysis. SEM results indicated that Unsvc TNT contained a variety of defects like cracks and porosity. Similarly, it is observed that thermal as well as kinetic behavior of both TNT samples vary to a great extent. Likewise, a prominent change in the activation energies (E) of both samples is observed. This in-depth study provides a way forward in finding solutions for the safe reutilization of decanted TNT.

Effect of feeding palm oil by-products based diets on total bacteria, cellulolytic bacteria and methanogenic archaea in the rumen of goats.

PubMed

Abubakr, Abdelrahim; Alimon, Abdul Razak; Yaakub, Halimatun; Abdullah, Norhani; Ivan, Michael

2014-01-01

Rumen microorganisms are responsible for digestion and utilization of dietary feeds by host ruminants. Unconventional feed resources could be used as alternatives in tropical areas where feed resources are insufficient in terms of quality and quantity. The objective of the present experiment was to evaluate the effect of diets based on palm oil (PO), decanter cake (DC) or palm kernel cake (PKC) on rumen total bacteria, selected cellulolytic bacteria, and methanogenic archaea. Four diets: control diet (CD), decanter cake diet (DCD), palm kernel cake diet (PKCD) and CD plus 5% PO diet (CPOD) were fed to rumen cannulated goats and rumen samples were collected at the start of the experimental diets (day 0) and on days 4, 6, 8, 12, 18, 24 and 30 post dietary treatments. Feeding DCD and PKCD resulted in significantly higher (P<0.05) DNA copy number of total bacteria, Fibrobacter succinogenes, Ruminococcus flavefeciens, and Ruminococcus albus. Rumen methanogenic archaea was significantly lower (P<0.05) in goats fed PKCD and CPOD and the trend showed a severe reduction on days 4 and 6 post experimental diets. In conclusion, results indicated that feeding DCD and PKC increased the populations of cellulolytic bacteria and decreased the density of methanogenic archaea in the rumen of goats.

Effect of feeding palm oil by-products based diets on muscle fatty acid composition in goats.

PubMed

Abubakr, Abdelrahim; Alimon, Abdul Razak; Yaakub, Halimatun; Abdullah, Norhani; Ivan, Michael

2015-01-01

The present study aims to evaluate the effects of feeding palm oil by-products based diets on different muscle fatty acid profiles in goats. Thirty-two Cacang × Boer goats were randomly assigned to four dietary treatments: (1) control diet (CD), (2) 80% decanter cake diet (DCD), (3) 80% palm kernel cake diet (PKCD) and (4) CD plus 5% palm oil (PO) supplemented diet (CPOD). After 100 days of feeding, four goats from each group were slaughtered and longissimus dorsi (LD), infraspinatus (IS) and biceps femoris (BF) were sampled for analysis of fatty acids. Goats fed the PKCD had higher (P<0.05) concentration of lauric acid (C12:0) than those fed the other diets in all the muscles tested. Compared to the other diets, the concentrations of palmitic acid (C16:0) and stearic acid (C18:0) were lower (P<0.05) and that of linoleic acid (C18:2 n-6) was higher (P<0.05) in the muscles from goats fed the CD. It was concluded that palm kernel cake and decanter cake can be included in the diet of goats up to 80% with more beneficial than detrimental effects on the fatty acid profile of their meat.

Influence of extraction techniques on physical-chemical characteristics and volatile compounds of extra virgin olive oil.

PubMed

Volpe, Maria Grazia; De Cunzo, Fausta; Siano, Francesco; Paolucci, Marina; Barbarisi, Costantina; Cammarota, Giancarlo

2014-01-01

The purpose of this study was to investigate three types of extraction methods of extra virgin olive oil (EVOO) from the same cultivar (Ortice olive cultivar): traditional or pressing (T) system, decanter centrifugation (DC) system and a patented horizontal axis decanter centrifugation (HADC) system. Oil samples were subjected to chemical analyses: free acidity, peroxide value, ultraviolet light absorption K232 and K270, total polyphenols, antioxidant capacity, volatile compounds and olfactory characteristics by electronic nose. The two centrifugation systems showed better free acidity and peroxides value but total polyphenol content was particularly high in extra virgin olive oil produced by patented HADC system. Same volatile substances that positively characterize the oil aroma were found in higher amount in the two centrifugation systems, although some differences have been detected between DC and HADC system, other were found in higher amount in extra virgin olive oil produced by T system. The electronic nose analysis confirmed these results, principal component analysis (PCA) and correlation matrix showed the major differences between EVOO produced by T and HADC system. Taken together the results showed that DC and HADC systems produce EVOO with better characteristics than T system and patented HADC is the best extraction system.

Synthesis and Characterization of Dipolar Organic Molecules for Nonlinear Optical Materials

DTIC Science & Technology

1992-05-08

BH3, THF; then, aqueous NaOH; ii. pyridinium chlorochromate , methylene chloride; iii. lithium diisopropylamide, THF 50 effective. After purification... pyridinium chlorochromate (1.5 g, 6.96 mmol) was added. The solution was stirred at room temperature for 48 hours. The organic solution was decanted from...the alcohol was oxidized to the aldehyde. Swern oxidation5 was first attempted but gave very low yield in our hands. Alternatively, pyridinium chloro

Photodissociation Dye Laser Studies and High Pressure Discharge Conditioning Studies

DTIC Science & Technology

1976-11-01

overnight to complete the formation of the Grignard reagent . The mixture was then cooled to room temperature and the solution was decanted ’.rom the...the Grignard reagent . A solution of the commercially available bromodiphenyl- methane (12.35 g) in the minimum quantity of dry benzene was then added...fairly rapidly into the reformed Hrignard reagent . A moderate exotherm was noted during this addition. The mixture was refluxed for two hours

Sedimentology, stratigraphy and chronology of a decantation tank in the sewer network of Orléans (France).

NASA Astrophysics Data System (ADS)

Jacob, Jérémy; Thibault, Alexandre; Simonneau, Anaëlle; Le Milbeau, Claude; DiGiovanni, Christian; Sabatier, Pierre; Reyss, Jean-Louis; Ardito, Luigi; Morio, Cédric

2017-04-01

Current debates on the status of the Anthropocene convey geologists and palaeoenvironmentalists toward new spatial and temporal targets. One of the most emblematic socio-ecosystem of the Anthropocene is urban areas in which the dynamics of materials are mainly controlled by human activities. This brings unprecedented elemental, molecular and isotopic concentrations and distributions that lead Norra (2009) to propose a new geological sphere: the Astysphere. Here we propose that sediments accumulated in sewer networks can provide original, integrated, and multi-thematic archives for the recent history of cities by considering urban systems as any catchment where materials are produced, transported and sedimented. The study site is a decantation tank that collects stormwater and wastewater from the north of Orléans city, upstream wastewater plants in Orléans. Sediments accumulated since 1942 over 17 m depth and were never cleaned out until 2015. Two sedimentary cores of 70 (A) and 250 cm long (B) were collected before clean out and then a third of 150 cm (C) after. Sediments are organized into layers constituted by sands and gravels alternating with silts and organic layers. Sharp contacts between those layers indicate evenemential sedimentation, as expected in sewer networks. We formulate the hypothesis that organic/mineral alternations result from a seasonal dynamic. 7Be presence in topmost sample from core A confirms it was deposited within the last 6 months. In core C, only the upper half core, mostly mineral, displays significant 7Be levels whereas 7Be is absent from the lower half, which is mostly organic. This would confirm that our hypothesis of a seasonal alternation, with organic facies deposited during spring- summer and mineral facies deposited during fall-winter. 30 14C dates measured on cores A and B by postbomb method are logically distributed with depth, the most ancient (beginning of the eighties) being recorder at 2.5m depth. This study shows that sediments accumulated in a decantation tank constitute sedimentary archives comparable to more natural ones, thus allowing palaeoenvironmental reconstructions for the Anthropocene. We are currently examining the mineral and organic content of this archive to provide a detailed chronology of the history of man-made materials (drugs, plastics, pesticides…) in urban contexts.

Constraints on JP-900 Jet Fuel Production Concepts

DTIC Science & Technology

2007-01-01

most of this research effort has focused on a coal-tar blending process. Penn State currently plans to build a one-barrel- per-day pilot plant and...which a mixture of solid coal and a refinery intermediate, decant oil, is used to pro- duce a combination of liquid fuels and coke. The findings and...petroleum refinery intermedi- ate (specifically, light cycle oil). More recently, attention has been directed toward a co-coking process, in which a

Effect of Feeding Palm Oil By-Products Based Diets on Total Bacteria, Cellulolytic Bacteria and Methanogenic Archaea in the Rumen of Goats

PubMed Central

Abubakr, Abdelrahim; Alimon, Abdul Razak; Yaakub, Halimatun; Abdullah, Norhani; Ivan, Michael

2014-01-01

Rumen microorganisms are responsible for digestion and utilization of dietary feeds by host ruminants. Unconventional feed resources could be used as alternatives in tropical areas where feed resources are insufficient in terms of quality and quantity. The objective of the present experiment was to evaluate the effect of diets based on palm oil (PO), decanter cake (DC) or palm kernel cake (PKC) on rumen total bacteria, selected cellulolytic bacteria, and methanogenic archaea. Four diets: control diet (CD), decanter cake diet (DCD), palm kernel cake diet (PKCD) and CD plus 5% PO diet (CPOD) were fed to rumen cannulated goats and rumen samples were collected at the start of the experimental diets (day 0) and on days 4, 6, 8, 12, 18, 24 and 30 post dietary treatments. Feeding DCD and PKCD resulted in significantly higher (P<0.05) DNA copy number of total bacteria, Fibrobacter succinogenes, Ruminococcus flavefeciens, and Ruminococcus albus. Rumen methanogenic archaea was significantly lower (P<0.05) in goats fed PKCD and CPOD and the trend showed a severe reduction on days 4 and 6 post experimental diets. In conclusion, results indicated that feeding DCD and PKC increased the populations of cellulolytic bacteria and decreased the density of methanogenic archaea in the rumen of goats. PMID:24756125

Carbothermic Aluminum Production Using Scrap Aluminum As A Coolant

DOEpatents

LaCamera, Alfred F.

2002-11-05

A process for producing aluminum metal by carbothermic reduction of alumina ore. Alumina ore is heated in the presence of carbon at an elevated temperature to produce an aluminum metal body contaminated with about 10-30% by wt. aluminum carbide. Aluminum metal or aluminum alloy scrap then is added to bring the temperature to about 900-1000.degree. C. and precipitate out aluminum carbide. The precipitated aluminum carbide is filtered, decanted, or fluxed with salt to form a molten body having reduced aluminum carbide content.

Application of thermogravimetric studies for optimization of lithium hexafluorophosphate production

NASA Astrophysics Data System (ADS)

Smagin, A. A.; Matyukha, V. A.; Korobtsev, V. P.

Lithium hexafluorophosphate, isolated from hydrogen fluoride solution (anhydrous) by decanting and filtering, is an adduct of composition LiPF 6*HF. By thermogravimetric investigations the dynamics of HF removal from LiPF 6 by LiPF 6*HF thermal decomposition was studied. Based on the experimental data the constants entering into the equations as C = C0*exp( t*K0* exp(- E/RT)) were calculated, explaining the thermal decomposition processes of LiPF 6*HF and LiPF 6.

Lead poisoning from drinking Kombucha tea brewed in a ceramic pot.

PubMed

Phan, T G; Estell, J; Duggin, G; Beer, I; Smith, D; Ferson, M J

Kombucha tea is an alternative therapy that is gaining popularity as a remedy for a diverse range of ailments. We report two cases of symptomatic lead poisoning requiring chelation therapy in a married couple who had been drinking Kombucha tea for six months, brewing the tea in a ceramic pot. We postulate that acids in the tea eluted lead from the glaze pigment used in the ceramic pot, in a manner analogous to elution of lead from crystal decanters by wine and spirits.

Liquid encapsulated crystal growth

NASA Technical Reports Server (NTRS)

Morrison, Andrew D. (Inventor)

1989-01-01

Low-defect crystals are grown in a closed ampoule under a layer of encapsulant. After crystal growth, the crystal is separated from the melt and moved into the layer of encapsulant and cooled to a first temperature at which crystal growth stops. The crystal is then moved into the inert gas ambient in the ampoule and further cooled. The crystal can be separated from the melt by decanting the melt into an adjacent reservoir or by rotating the ampoule to rotate the crystal into the encapsulant layer.

Liquid encapsulated crystal growth

NASA Technical Reports Server (NTRS)

Morrison, Andrew D. (Inventor)

1987-01-01

Low-defect crystals are grown in a closed ampoule under a layer of encapsulant. After crystal growth, the crystal is separated from the melt and moved into the layer of encapsulant and cooled to a first temperature at which crystal growth stops. The crystal is then moved into the inert gas ambient in the ampoule and further cooled. The crystal can be separated from the melt by decanting the melt into and adjacent reservoir or by rotating the ampoule to rotate the crystal into the encapsulant layer.

Compatibility and Decontamination of High-Density Polyethylene Exposed to Sulfur Mustard

DTIC Science & Technology

2014-05-01

HD in accordance with (IAW) the Environmental Monitoring Laboratory ([ EML ) Internal Operating Procedure (IOP) MT-60.1...60 oC. h. After 1 h, MEA was decanted into another 40 mL VOA vial. i. The MEA neutralent was extracted and analyzed for HD IAW EML IOP MT-60.1 j...procedures found in EML IOP MT-60.1 n. The coupon was vapor washed in a sample bottle with nitrogen for 15 min and placed in a 10 × 10 in. plastic bag

Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karnofsky, G. B.

1980-12-16

A process for solvent extraction of oil from oil bearing diatomite ore and an apparatus for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent, solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom, and solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure.

Esterification of oil adsorbed on palm decanter cake into methyl ester using sulfonated rice husk ash as heterogeneous acid catalyst

NASA Astrophysics Data System (ADS)

Hindryawati, Noor; Erwin, Maniam, Gaanty Pragas

2017-02-01

Palm Decanter cake (PDC) which is categorized as the waste from palm oil mill has been found to contain residual crude palm oil. The oil adsorbed on the PDC (PDC-oil) can be extracted and potentially used as feedstock for biodiesel production. Feedstock from waste like PDC-oil is burdened with high free fatty acids (FFAs) which make the feedstock difficult to be converted into biodiesel using basic catalyst. Therefore, in this study, a solid acid, RHA-SO3H catalyst was synthesized by sulfonating rice husk ash (RHA) with concentrated sulfuric acid. The RHA-SO3H prepared was characterized with TGA, FTIR, BET, XRD, FE-SEM, and Hammett indicators (methyl red, bromophenol blue, and crystal violet). PDC was found to have about 11.3 wt. % oil recovered after 1 hour extraction using ultrasound method. The presence of sulfonate group was observed in IR spectrum, and the surface area of RHA-SO3H was reduced to 37 m2.g-1 after impregnation of sulfonate group. The RHA-SO3H catalyst showed that it can work for both esterification of free fatty acid which is present in PDC-oil, and transesterification of triglycerides into methyl ester. The results showed highest methyl ester content of 70.2 wt.% at optimal conditions, which was 6 wt.% catalyst amount, methanol to oil molar ratio of 17:1 for 5 hours at 120 °C.

Extraction process for removing metallic impurities from alkalide metals

DOEpatents

Royer, L.T.

1987-03-20

A development is described for removing metallic impurities from alkali metals by employing an extraction process wherein the metallic impurities are extracted from a molten alkali metal into molten lithium metal due to the immiscibility of the alkali metals in lithium and the miscibility of the metallic contaminants or impurities in the lithium. The purified alkali metal may be readily separated from the contaminant-containing lithium metal by simple decanting due to the differences in densities and melting temperatures of the alkali metals as compared to lithium.

Protocol for the Meningococcal Control Programme - Canadian Forces Base Cornwallis and Canadian Forces Base St. Jean 1980/81,

DTIC Science & Technology

1980-11-01

hours, then overnight in a refrigerator or cold room at 40C. Fol- lowing clot retraction , the serum may be decanted and spun, or the whole sample spun...Drogram. The SIMP programme may involve one or all of the following: collection of post nasal swabs, blood sera samples, air samples and surface samples...outlined in para 16. 16. Culturing of Swabs Swabs shall be placed on Columbia Blood Agar (4 or 5% sheep RBC’s) supplemented with IsoVitalex (Baltimore

A Computer Compatible System for the Categorization, Enumeration, and Retrieval of Nineteenth and Early Twentieth Century Archaeological Material Culture. Part 2. Manual for Identification and Classification.

DTIC Science & Technology

1983-12-01

process, when aged and subject to archaeological conditions, often blackens. (14) Jewelry set This category includes all cut or ground glass insets used to...individually ground to fit, and in fact the ground glass stoppers are still in use for decanters and perfume bottles. After this date, bottle openings...hollow ground and heavier at one end. Safety razors using separate blades did not appear commercially until the first . decade of the twentieth century

Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karnofsky, G.B.

1979-09-11

A process is described for solvent extraction of oil-bearing diatomite ore. An apparatus is provided for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent. The solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom. The solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure. 17 claims.

Continuous chemical operations and modifications on magnetic γ-Fe2O3 nanoparticles confined in nanoliter droplets for the assembly of fluorescent and magnetic SiO2@γ-Fe2O3.

PubMed

Ferraro, D; Lin, Y; Teste, B; Talbot, D; Malaquin, L; Descroix, S; Abou-Hassan, A

2015-12-11

We present a microfluidic platform that allows undergoing different chemical operations in a nanoliter droplet starting from the colloidal suspension of magnetic iron oxide (γ-Fe2O3) nanoparticles "NPs" (ferrofluid). These operations include: mixing, flocculation, magnetic decantation, colloidal redispersion, washing, surface functionalization, heating and colloidal assembly. To prove the platform capabilities, we produced fluorescent and magnetic nanoassemblies composed of fluorescent silica and magnetic NPs.

Roll, Spin, Wash, or Filter? Processing of Lipoaspirate for Autologous Fat Grafting: An Updated, Evidence-Based Review of the Literature.

PubMed

Cleveland, Emily C; Albano, Nicholas J; Hazen, Alexes

2015-10-01

The use of autologous adipose tissue harvested through liposuction techniques for soft-tissue augmentation has become commonplace among cosmetic and reconstructive surgeons alike. Despite its longstanding use in the plastic surgery community, substantial controversy remains regarding the optimal method of processing harvested lipoaspirate before grafting. This evidence-based review builds on prior examinations of the literature to evaluate both established and novel methods for lipoaspirate processing. A comprehensive, systematic review of the literature was conducted using Ovid MEDLINE in January of 2015 to identify all relevant publications subsequent to the most recent review on this topic. Randomized controlled trials, clinical trials, and comparative studies comparing at least two of the following techniques were included: decanting, cotton gauze (Telfa) rolling, centrifugation, washing, filtration, and stromal vascular fraction isolation. Nine articles comparing various methods of processing human fat for autologous grafting were selected based on inclusion and exclusion criteria. Five compared established processing techniques (i.e., decanting, cotton gauze rolling, centrifugation, and washing) and four publications evaluated newer proprietary technologies, including washing, filtration, and/or methods to isolate stromal vascular fraction. The authors failed to find compelling evidence to advocate a single technique as the superior method for processing lipoaspirate in preparation for autologous fat grafting. A paucity of high-quality data continues to limit the clinician's ability to determine the optimal method for purifying harvested adipose tissue. Novel automated technologies hold promise, particularly for large-volume fat grafting; however, extensive additional research is required to understand their true utility and efficiency in clinical settings.

SLUDGE TREATMENT PROJECT COST COMPARISON BETWEEN HYDRAULIC LOADING AND SMALL CANISTER LOADING CONCEPTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

GEUTHER J; CONRAD EA; RHOADARMER D

2009-08-24

The Sludge Treatment Project (STP) is considering two different concepts for the retrieval, loading, transport and interim storage of the K Basin sludge. The two design concepts under consideration are: (1) Hydraulic Loading Concept - In the hydraulic loading concept, the sludge is retrieved from the Engineered Containers directly into the Sludge Transport and Storage Container (STSC) while located in the STS cask in the modified KW Basin Annex. The sludge is loaded via a series of transfer, settle, decant, and filtration return steps until the STSC sludge transportation limits are met. The STSC is then transported to T Plantmore » and placed in storage arrays in the T Plant canyon cells for interim storage. (2) Small Canister Concept - In the small canister concept, the sludge is transferred from the Engineered Containers (ECs) into a settling vessel. After settling and decanting, the sludge is loaded underwater into small canisters. The small canisters are then transferred to the existing Fuel Transport System (FTS) where they are loaded underwater into the FTS Shielded Transfer Cask (STC). The STC is raised from the basin and placed into the Cask Transfer Overpack (CTO), loaded onto the trailer in the KW Basin Annex for transport to T Plant. At T Plant, the CTO is removed from the transport trailer and placed on the canyon deck. The CTO and STC are opened and the small canisters are removed using the canyon crane and placed into an STSC. The STSC is closed, and placed in storage arrays in the T Plant canyon cells for interim storage. The purpose of the cost estimate is to provide a comparison of the two concepts described.« less

Chemical Data for Precipitate Samples

USGS Publications Warehouse

Foster, Andrea L.; Koski, Randolph A.

2008-01-01

During studies of sulfide oxidation in coastal areas of Prince William Sound in 2005, precipitate samples were collected from onshore and intertidal locations near the Ellamar, Threeman, and Beatson mine sites (chapter A, fig. 1; table 7). The precipitates include jarosite and amorphous Fe oxyhydroxide from Ellamar, amorphous Fe oxyhydroxide from Threeman, and amorphous Fe oxyhydroxide, ferrihydrite, and schwertmannite from Beatson. Precipitates occurring in the form of loose, flocculant coatings were harvested using a syringe and concentrated in the field by repetitive decanting. Thicker accumulations were either scraped gently from rocks using a stainless steel spatula or were scooped directly into receptacles (polyethylene jars or plastic heavy-duty zippered bags). Most precipitate samples contain small amounts of sedimentary detritus. With three jarosite-bearing samples from Ellamar, an attempt was made to separate the precipitate from the heavy-mineral fraction of the sediment. In this procedure, the sample was stirred in a graduated cylinder containing deionized water. The jarosite-rich suspension was decanted onto analytical filter paper and air dried before analysis. Eleven precipitate samples from the three mine sites were analyzed in laboratories of the U.S. Geological Survey (USGS) in Denver, Colorado (table 8). Major and trace elements were determined by inductively coupled plasma-mass spectrometry following multiacid (HCl-HNO3-HClO4-HF) digestion (Briggs and Meier, 2002), except for mercury, which was analyzed by cold-vapor atomic absorption spectroscopy (Brown and others, 2002a). X-ray diffraction (XRD) analyses were performed on powdered samples (<200 mesh) by S. Sutley of the USGS. Additional details regarding sample preparation and detection limits are found in Taggert (2002). Discussions of the precipitate chemistry and associated microbial communities are presented in Koski and others (2008) and Foster and others (2008), respectively.

Vapor Corrosion Response of Low Carbon Steel Exposed to Simulated High Level Radioactive Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiersma, B

2006-01-26

A program to resolve the issues associated with potential vapor space corrosion and liquid/air interface corrosion in the Type III high level waste tanks is in place. The objective of the program is to develop understanding of vapor space (VSC) and liquid/air interface (LAIC) corrosion to ensure a defensible technical basis to provide accurate corrosion evaluations with regard to vapor space and liquid/air interface corrosion. The results of the FY05 experiments are presented here. The experiments are an extension of the previous research on the corrosion of tank steel exposed to simple solutions to corrosion of the steel when exposedmore » to complex high level waste simulants. The testing suggested that decanting and the consequent residual species on the tank wall is the predominant source of surface chemistry on the tank wall. The laboratory testing has shown that at the boundary conditions of the chemistry control program for solutions greater than 1M NaNO{sub 3}{sup -}. Minor and isolated pitting is possible within crevices in the vapor space of the tanks that contain stagnant dilute solution for an extended period of time, specifically when residues are left on the tank wall during decanting. Liquid/air interfacial corrosion is possible in dilute stagnant solutions, particularly with high concentrations of chloride. The experimental results indicate that Tank 50 would be most susceptible to the potential for liquid/air interfacial corrosion or vapor space corrosion, with Tank 49 and 41 following, since these tanks are nearest to the chemistry control boundary conditions. The testing continues to show that the combination of well-inhibited solutions and mill-scale sufficiently protect against pitting in the Type III tanks.« less

FORMATION OF URANIUM PRECIPITATES

DOEpatents

Googin, J.M. Jr.

1959-03-17

A method is described for precipitation of uranium peroxide from uranium- containing solutions so as to obtain larger aggregates which facilitates washings decantations filtrations centrifugations and the like. The desired larger aggregate form is obtained by maintaining the pH of the solution in the approximate range of 1 to 3 and the temperature at about 25 deg C or below while carrytng out the precipitation. Then prior to removal of the precipitate a surface active sulfonated bicarboxyacids such as di-octyl sodium sulfo-succinates is incorporated in an anount of the order of 0.01 to 0.05 percent by weights and the slurry is allowed to ripen for about one-half hour at a temperatare below 10 deg C.

Chemical treatment of low-grade uranium ores. Extraction of uranium from tricalcium phosphate; TRAITEMENT CHIMIQUE DES MINERAIS PAUVRES D'URANIUM. EXTRACTION DE L'URANIUM DU PHOSPHATE TRICALCIQUE (in French)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mechelynck, Ph.

1958-07-15

After an examination of the different processes for the treatment of uranium minerals, it is concluded that the extraction of uranium by ion exchange is not applicable to hydrochloric acid solutions of phosphates. A sulfuric or phosphoric solution can be used. For solvent extraction of uranium, sulfuric or phosphoric solutions are the best, but hydrochloric solutions can be used. The cost of the solvents used would determine the cost of the operation. It is necessary, in the case of liquid-liquid extraction, to filter or decant the solution before extraction. (tr-auth)

Entrapping of fullerenes, nanotubes, and inorganic nanoparticles by a DNA-chitosan complex: a method for nanomaterials removal.

PubMed

Zinchenko, Anatoly A; Maeda, Noriko; Pu, Shengyan; Murata, Shizuaki

2013-05-07

We report a protocol for entrapping of various water-dispersed nanomaterials: fullerenes, multiwall carbon nanotubes, quantum dots (semiconductor nanoparticles), and gold nanorods, into a DNA-chitosan complex. In contrast to small-size nanomaterial particles, the bulky DNA-chitosan interpolyelectrolyte complex incorporating the dispersed nanomaterials can be easily separated from aqueous media by centrifugation, filtration, or decantation. While the removal of nanoparticles by centrifugation is equally efficient for every type of nanoparticles and reaches 100%, the higher efficiency of the nanomaterials removal by other two methods is favored by larger size of nanoparticles. The application of this entrapping protocol for removal of nanomaterials from water is discussed.

Technology for the production of Zero Q.I pitch from coal tar

NASA Astrophysics Data System (ADS)

Karthik, K.; Kumar, K. Rajesh; Rao, C. V. Nageswara; Kumar, B. Vinod; Murty, J. V. S.

2013-06-01

Zero Quinoline Insolubles (Q.I) pitch is a special type of pitch obtained from pre-treatment of coal tar, which is converted into pitch. This is used for impregnation of electrodes for improving the strength, electrical properties and also used as a pre-cursor for Mesophase pitch for producing Mesophase pitch based carbon fibers, carbon foam, and Meso carbon micro beads. This paper discusses the technology of Q.I separation from Coal Tar by using decantation of Coal Tar mixed with Heavy Creosote Oil (HC Oil) at different temperatures. By this method we were able to produce the Zero Q.I pitch with a Q.I value of 0.1%.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herman, D.

The Savannah River Site (SRS) Actinide Removal Process has been processing salt waste since 2008. This process includes a filtration step in the 512-S facility. Initial operations included the addition, or strike, of monosodium titanate (MST) to remove soluble actinides and strontium. The added MST and any entrained sludge solids were then separated from the supernate by cross flow filtration. During this time, the filter operations have, on many occasions, been the bottleneck process limiting the rate of salt processing. Recently, 512-S- has started operations utilizing “No-MST” where the MST actinide removal strike was not performed and the supernate wasmore » simply pre-filtered prior to Cs removal processing. Direct filtration of decanted tank supernate, as demonstrated in 512-S, is the proposed method of operation for the Hanford Low Activity Waste Pretreatment System (LAWPS) facility. Processing decanted supernate without MST solids has been demonstrated for cross flow filtration to provide a significant improvement in production with the SRS Salt Batches 8 and 9 feed chemistries. The average filtration rate for the first 512-S batch processing cycle using No-MST has increased filtrate production by over 35% of the historical average. The increase was sustained for more than double the amount of filtrate batches processed before cleaning of the filter was necessary. While there are differences in the design of the 512-S and Hanford filter systems, the 512-S system should provide a reasonable indication of LAWPS filter performance with similar feed properties. Based on the data from the 512-S facility and with favorable feed properties, the LAWPS filter, as currently sized at over twice the size of the 512-S filter (532 square feet filtration area versus 235 square feet), has the potential to provide sustained filtrate production at the upper range of the planned LAWPS production rate of 17 gpm.« less

Process for Making Single-Domain Magnetite Crystals

NASA Technical Reports Server (NTRS)

Golden, D. C.; Ming, Douglas W.; Morris, Richard V.; Lofgren, Gary E.; McKay, Gordan A.; Schwandt, Craig S.; Lauer, Howard V., Jr.; Socki, Richard A.

2004-01-01

A process for making chemically pure, single-domain magnetite crystals substantially free of structural defects has been invented as a byproduct of research into the origin of globules in a meteorite found in Antarctica and believed to have originated on Mars. The globules in the meteorite comprise layers of mixed (Mg, Fe, and Ca) carbonates, magnetite, and iron sulfides. Since the discovery of the meteorite was announced in August 1996, scientists have debated whether the globules are of biological origin or were formed from inorganic materials by processes that could have taken place on Mars. While the research that led to the present invention has not provided a definitive conclusion concerning the origin of the globules, it has shown that globules of a different but related chemically layered structure can be grown from inorganic ingredients in a multistep precipitation process. As described in more detail below, the present invention comprises the multistep precipitation process plus a subsequent heat treatment. The multistep precipitation process was demonstrated in a laboratory experiment on the growth of submicron ankerite crystals, overgrown by submicron siderite and pyrite crystals, overgrown by submicron magnesite crystals, overgrown by submicron siderite and pyrite. In each step, chloride salts of appropriate cations (Ca, Fe, and Mg) were dissolved in deoxygenated, CO2- saturated water. NaHCO3 was added as a pH buffer while CO2 was passed continuously through the solution. A 15-mL aliquot of the resulting solution was transferred into each of several 20 mL, poly(tetrafluoroethylene)-lined hydrothermal pressure vessels. The vessels were closed in a CO2 atmosphere, then transferred into an oven at a temperature of 150 C. After a predetermined time, the hydrothermal vessels were removed from the oven and quenched in a freezer. Supernatant solutions were decanted, and carbonate precipitates were washed free of soluble salts by repeated decantations with deionized water.

Life cycle assessment of pig slurry treatment technologies for nutrient redistribution in Denmark.

PubMed

ten Hoeve, Marieke; Hutchings, Nicholas J; Peters, Gregory M; Svanström, Magdalena; Jensen, Lars S; Bruun, Sander

2014-01-01

Animal slurry management is associated with a range of impacts on fossil resource use and the environment. The impacts are greatest when large amounts of nutrient-rich slurry from livestock production cannot be adequately utilised on adjacent land. To facilitate nutrient redistribution, a range of different technologies are available. This study comprised a life cycle assessment of the environmental impacts from handling 1000 kg of pig slurry ex-animal. Application of untreated pig slurry onto adjacent land was compared with using four different treatment technologies to enable nutrient redistribution before land application: (a) separation by mechanical screw press, (b) screw press separation with composting of the solid fraction, (c) separation by decanter centrifuge, and (d) decanter centrifuge separation with ammonia stripping of the liquid fraction. Emissions were determined based on a combination of values derived from the literature and simulations with the Farm-N model for Danish agricultural and climatic conditions. The environmental impact categories assessed were climate change, freshwater eutrophication, marine eutrophication, terrestrial acidification, natural resource use, and soil carbon, nitrogen and phosphorus storage. In all separation scenarios, the liquid fraction was applied to land on the pig-producing (donor) farm and the solid fraction transported to a recipient farm and utilised for crop production. Separation, especially by centrifuge, was found to result in a lower environmental impact potential than application of untreated slurry to adjacent land. Composting and ammonia stripping either slightly increased or slightly decreased the environmental impact potential, depending on the impact category considered. The relative ranking of scenarios did not change after a sensitivity analysis in which coefficients for field emissions of nitrous oxide, ammonia and phosphorus were varied within the range cited in the literature. Therefore, the best technology to implement in a given situation depends on the environmental problem in question, local policy, cost and practicality. Copyright © 2013 Elsevier Ltd. All rights reserved.

Engineered river flow-through to improve mine pit lake and river values.

PubMed

McCullough, Cherie D; Schultze, Martin

2018-05-30

Mine pit lakes may develop at mine closure when mining voids extend below groundwater levels and fill with water. Acid and metalliferous drainage (AMD) and salinity are common problems for pit lake water quality. Contaminated pit lake waters can directly present significant risk to both surrounding and regional communities and natural environmental values and limit beneficial end use opportunities. Pit lake waters can also discharge into surface and groundwater; or directly present risks to wildlife, stock and human end users. Riverine flow-through is increasingly proposed to mitigate or remediate pit lake water contamination using catchment scale processes. This paper presents the motivation and key processes and considerations for a flow-through pit lake closure strategy. International case studies as precedent and lessons for future application are described from pit lakes that use or propose flow-through as a key component of their mine closure design. Chemical and biological processes including dilution, absorption and flocculation and sedimentation can sustainably reduce pit lake contaminant concentrations to acceptable levels for risk and enable end use opportunities to be realised. Flow-through may be a valid mine closure strategy for pit lakes with poor water quality. However, maintenance of existing riverine system values must be foremost. We further suggest that decant river water quality may, in some circumstances, be improved; notably in examples of meso-eutrophic river waters flowing through slightly acidic pit lakes. Flow-through closure strategies must be scientifically justifiable and risk-based for both lake and receptors potentially affected by surface and groundwater transport. Due to the high-uncertainty associated with this complex strategy, biotic and physico-chemical attributes of both inflow and decant river reaches as well as lake should be well monitored. Monitoring should directly feed into an adaptive management framework discussed with key stakeholders with validation of flow-through as a sustainable strategy prior to mine relinquishment. Copyright © 2018 Elsevier B.V. All rights reserved.

A sample-to-result system for blood coagulation tests on a microfluidic disk analyzer

PubMed Central

Lin, Chia-Hui; Liu, Cheng-Yuan; Shih, Chih-Hsin; Lu, Chien-Hsing

2014-01-01

In this report, we describe in detail a microfluidic analyzer, which is able to conduct blood coagulation tests using whole blood samples. Sample preparation steps, such as whole blood aliquoting and metering, plasma separation, decanting, and mixing with reagents were performed in sequence through microfluidic functions integrated on a disk. Both prothrombin time (PT) and activated partial thromboplastin time (aPTT) were carried out on the same platform and the test results can be reported in 5 min. Fifty clinical samples were tested for both PT and aPTT utilizing the microfluidic disk analyzer and the instrument used in hospitals. The test results showed good correlation and agreement between the two instruments. PMID:25332733

Synthesis and characterization of ionic liquid immobilized on magnetic nanoparticles: A recyclable heterogeneous organocatalyst for the acetylation of alcohols

NASA Astrophysics Data System (ADS)

Ghorbani-Choghamarani, Arash; Norouzi, Masoomeh

2016-03-01

Herein, we describe a simple and efficient procedure for the preparation of 3-((3-(trisilyloxy)propyl)propionamide)-1-methylimidazolium chloride ionic liquid supported on magnetic nanoparticle (TPPA-IL-Fe3O4). The structure of this magnetic ionic liquid is fully characterized by FT-IR, TGA, XRD, VSM, SEM, EDX and DLS techniques. TPPA-IL-Fe3O4 is employed as a catalyst for the acetylation of alcohols with acetic anhydride under mild and heterogeneous conditions at room temperature with good to excellent yields. The magnetic catalyst could be readily separate from the reaction media by simple magnetic decantation, and reused several times without significant loss of its catalytic activity.

Ancient Martian valley genesis and paleoclimatic inference: The present as a key to the past

NASA Technical Reports Server (NTRS)

Brakenridge, G. R.

1993-01-01

I offer here the speculative genetic hypothesis that the flat-floored landforms represent episodically active, sediment-laden valley glaciers formed by localized geothermal melting of abundant interstitial ice (permafrost) in a fine-grained sedimentary terrain. Geothermal melting may also localize spring heads for the narrow deep, high-gradient valleys, or the collapse process itself may result in the generation of decanted, relatively sediment-poor overland water flows (some local evidence of fluid overtopping of the localized depressions exists). Whatever the generic mechanisms for the suite of valley landforms, perhaps the most interesting observation is simply their youth. In aggregate, the morphologies are similar to the ancient valley systems cited as evidence for a previously much denser atmosphere on Mars.

[Detection of pathogenic leptospira in the waste water and sewage sludge of large pig breeding sites].

PubMed

Mînzat, R M; Tomescu, V

1975-01-01

Sewage effluent and sludge from the purification plant of 8 large piggeries was examined for the presence of pathogenic leptospires. By using the methods of Appelman and Van Thiel it was found that 43.1% of samples of effluent were contaminated with L. pomona and O. tarassovi. Altogether 33 strains of pomona and three mixed cultures of pomona and tarassovi were obtained. The isolated strains were shown to be pathogenic by experimental infection of guinea-pigs, rabbits and pregnant and non-pregnant sows. The average period of survival of pathogenic leptospires in sewage effluent was 24 to 48 hours, with a maximum of 96 hours. Leptospires were killed within 24 hours in decanted sludge, owing to its strong acidity.

Hyperthermia in low aspect-ratio magnetic nanotubes for biomedical applications

NASA Astrophysics Data System (ADS)

Gutierrez-Guzman, D. F.; Lizardi, L. I.; Otálora, J. A.; Landeros, P.

2017-03-01

A simple model for the magnetization reversal process of low aspect-ratio ferromagnetic nanotubes (MNTs) is presented. Because of advantages over other geometries, these structures are interesting for biomedical applications, such as magnetic hyperthermia cancer therapy, where the heat released during magnetic reversal is used to destroy tumors. For example, the tubular geometry provides two independent functional surfaces that may be selectively manipulated and also gives a storage cavity. Owing to their large surface to weight ratio and low mass density, MNTs are not decanted by gravity. We calculated magnetic phase diagrams, energy barriers, nucleation fields, and the amount of dissipated heat and specific absorption rate for magnetite nanotubes. The geometrical parameters were varied, and simple formulae were used to optimize the tube response under alternating excitation, as required for magnetic hyperthermia applications.

La Meme Chose: How Mathematics Can Explain the Thinking of Children and the Thinking of Children Can Illuminate Mathematical Philosophy

NASA Astrophysics Data System (ADS)

Cable, John

2014-01-01

This article offers a new interpretation of Piaget's decanting experiments, employing the mathematical notion of equivalence instead of conservation. Some reference is made to Piaget's theories and to his educational legacy, but the focus in on certain of the experiments. The key to the new analysis is the abstraction principle, which has been formally enunciated in mathematical philosophy but has universal application. It becomes necessary to identity fluid objects (both configured and unconfigured) and configured and unconfigured sets-of-objects. Issues emerge regarding the conflict between philosophic realism and anti-realism, including constructivism. Questions are asked concerning mathematics and mathematical philosophy, particularly over the nature of sets, the wisdom of the axiomatic method and aspects of the abstraction principle itself.

The Resin-in-pulp Process and Its Application to Ores from Brosses "BRS 10"; LE PROCEDE "RESIN IN PULP" ET SON APPLICATION AUX MINERAIS DES BROSSES "BRS 10"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kremer, M.

1959-03-01

The resin-in-pulp process is a technical variant of the recovery process of uranium in dilute solution by means of ion exchange resins. An anion resin, XE 123, of a welldefined grain size is placed in direct contact with the pulp produced by sulfuric acid attack on ore with a low uranium content. This process is of particular value in the treatment of pulps that cannot be filtered or decanted, such as those obtained with ore from Brosses. The preparation of the pulp, the elution of the uranium, and its fixation, as well as the various factors encountered in these operations,more » are discussed. (auth)« less

Decarbonization process for carbothermically produced aluminum

DOEpatents

Bruno, Marshall J.; Carkin, Gerald E.; DeYoung, David H.; Dunlap, Sr., Ronald M.

2015-06-30

A method of recovering aluminum is provided. An alloy melt having Al.sub.4C.sub.3 and aluminum is provided. This mixture is cooled and then a sufficient amount of a finely dispersed gas is added to the alloy melt at a temperature of about 700.degree. C. to about 900.degree. C. The aluminum recovered is a decarbonized carbothermically produced aluminum where the step of adding a sufficient amount of the finely dispersed gas effects separation of the aluminum from the Al.sub.4C.sub.3 precipitates by flotation, resulting in two phases with the Al.sub.4C.sub.3 precipitates being the upper layer and the decarbonized aluminum being the lower layer. The aluminum is then recovered from the Al.sub.4C.sub.3 precipitates through decanting.

SLUDGE TREATMENT PROJECT ENGINEERED CONTAINER RETRIEVAL AND TRANSFER SYSTEM PRELMINARY DESIGN HAZARD AND OPERABILITY STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

CARRO CA

2011-07-15

This Hazard and Operability (HAZOP) study addresses the Sludge Treatment Project (STP) Engineered Container Retrieval and Transfer System (ECRTS) preliminary design for retrieving sludge from underwater engineered containers located in the 105-K West (KW) Basin, transferring the sludge as a sludge-water slurry (hereafter referred to as 'slurry') to a Sludge Transport and Storage Container (STSC) located in a Modified KW Basin Annex, and preparing the STSC for transport to T Plant using the Sludge Transport System (STS). There are six, underwater engineered containers located in the KW Basin that, at the time of sludge retrieval, will contain an estimated volumemore » of 5.2 m{sup 3} of KW Basin floor and pit sludge, 18.4 m{sup 3} of 105-K East (KE) Basin floor, pit, and canister sludge, and 3.5 m{sup 3} of settler tank sludge. The KE and KW Basin sludge consists of fuel corrosion products (including metallic uranium, and fission and activation products), small fuel fragments, iron and aluminum oxide, sand, dirt, operational debris, and biological debris. The settler tank sludge consists of sludge generated by the washing of KE and KW Basin fuel in the Primary Clean Machine. A detailed description of the origin of sludge and its chemical and physical characteristics can be found in HNF-41051, Preliminary STP Container and Settler Sludge Process System Description and Material Balance. In summary, the ECRTS retrieves sludge from the engineered containers and hydraulically transfers it as a slurry into an STSC positioned within a trailer-mounted STS cask located in a Modified KW Basin Annex. The slurry is allowed to settle within the STSC to concentrate the solids and clarify the supernate. After a prescribed settling period the supernate is decanted. The decanted supernate is filtered through a sand filter and returned to the basin. Subsequent batches of slurry are added to the STSC, settled, and excess supernate removed until the prescribed quantity of sludge is collected. The sand filter is then backwashed into the STSC. The STSC and STS cask are then inerted and transported to T Plant.« less

Non-whole beat correlation method for the identification of an unbalance response of a dual-rotor system with a slight rotating speed difference

NASA Astrophysics Data System (ADS)

Zhang, Z. X.; Wang, L. Z.; Jin, Z. J.; Zhang, Q.; Li, X. L.

2013-08-01

The efficient identification of the unbalanced responses in the inner and outer rotors from the beat vibration is the key step in the dynamic balancing of a dual-rotor system with a slight rotating speed difference. This paper proposes a non-whole beat correlation method to identify the unbalance responses whose integral time is shorter than the whole beat correlation method. The principle, algorithm and parameter selection of the proposed method is emphatically demonstrated in this paper. From the numerical simulation and balancing experiment conducted on horizontal decanter centrifuge, conclusions can be drawn that the proposed approach is feasible and practicable. This method makes important sense in developing the field balancing equipment based on portable Single Chip Microcomputer (SCMC) with low expense.

Apparatus and methods for purifying lead

DOEpatents

Tunison, Harmon M.

2016-01-12

Disclosed is an exemplary method of purifying lead which includes the steps of placing lead and a fluoride salt blend in a container; forming a first fluid of molten lead at a first temperature; forming a second fluid of the molten fluoride salt blend at a second temperature higher than the first temperature; mixing the first fluid and the second fluid together; separating the two fluids; solidifying the molten fluoride salt blend at a temperature above a melting point of the lead; and removing the molten lead from the container. In certain exemplary methods the molten lead is removed from the container by decanting. In still other exemplary methods the molten salt blend is a Lewis base fluoride eutectic salt blend, and in yet other exemplary methods the molten salt blend contains sodium fluoride, lithium fluoride, and potassium fluoride.

Settling and survival profile of enteric pathogens in the swine effluent for water reuse purpose.

PubMed

Fongaro, G; Kunz, A; Magri, M E; Schissi, C D; Viancelli, A; Philippi, L S; Barardi, C R M

2016-11-01

The present study evaluated the pathogens persistence and settling profile in swine effluent. We determined the enteric pathogens settling characteristics, their survival and inactivation profile in swine effluent (for water reuse purpose) and in sludge (generated after aerobic treatment - during secondary settling process). The study was performed in laboratorial-scale and in full-scale (manure treatment plant). Enteric viruses and enteric bacteria were used as biomarkers. Results showed that these enteric pathogens were significantly reduced from swine effluent during secondary settling process, and enteric viruses removal was correlated with the suspended solids decantation. The design of secondary settlers can be adapted to improve pathogens removal, by diminishing the solids loading rate per area and time, ending in higher hydraulic retention times. Copyright © 2016 Elsevier GmbH. All rights reserved.

Mass Transfer And Hydraulic Testing Of The V-05 And V-10 Contactors With The Next Generation Solvent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herman, D. T.; Duignan, M. R.; Williams, M. R.

The Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) facility is actively pursuing the transition from the current BOBCalixC6 based solvent to the Next Generation Solvent (NGS)-MCU solvent. To support this integration of NGS into the MCU facilities, Savannah River Remediation (SRR) requested that Savannah River National Laboratory (SRNL) perform testing of a blend of the NGS (MaxCalix based solvent) with the current solvent (BOBCalixC6 based solvent) for the removal of cesium (Cs) from the liquid salt waste stream. This testing differs from prior testing by utilizing a blend of BOBCalixC6 based solvent and the NGS with the full (0.05more » M) concentration of the MaxCalix as well as a new suppressor, tris(3,7dimethyloctyl) guanidine. Single stage tests were conducted using the full size V-05 and V-10 centrifugal contactors installed at SRNL. These tests were designed to determine the mass transfer and hydraulic characteristics with the NGS solvent blended with the projected heel of the BOBCalixC6 based solvent that will exist in MCU at time of transition. The test program evaluated the amount of organic carryover and the droplet size of the organic carryover phases using several analytical methods. Stage efficiency and mass distribution ratios were determined by measuring Cs concentration in the aqueous and organic phases during single contactor testing. The nominal cesium distribution ratio, D(Cs) measured for extraction ranged from 37-60. The data showed greater than 96% stage efficiency for extraction. No significant differences were noted for operations at 4, 8 or 12 gpm aqueous salt simulant feed flow rates. The first scrub test (contact with weak caustic solution) yielded average scrub D(Cs) values of 3.3 to 5.2 and the second scrub test produced an average value of 1.8 to 2.3. For stripping behavior, the “first stage” D Cs) values ranged from 0.04 to 0.08. The efficiency of the low flow (0.27 gpm aqueous) was calculated to be 82.7%. The Spreadsheet Algorithm for Stagewise Solvent Extraction (SASSE) predicted equivalent DF for MCU from this testing is greater than 3,500 assuming 95% efficiency during extraction and 80% efficiency during scrub and strip. Hydraulically, the system performed very well in all tests. Target flows were easily obtained and stable throughout testing. Though some issues were encountered with plugging in the coalescer, they were not related to the solvent. No hydraulic upsets due to the solvent were experienced during any of the tests conducted. The first extraction coalescer element used in testing developed high pressure drop that made it difficult to maintain the target flow rates. Analysis showed an accumulation of sodium aluminosilicate solids. The coalescer was replaced with one from the same manufacturer’s lot and pressure drop was no longer an issue. Concentrations of Isopar™ L and Modifier were measured using semi-volatile organic analysis (SVOA) and high performance liquid chromatography (HPLC) to determine the amount of solvent carryover. For low-flow (0.27 gpm aqueous) conditions in stripping, SVOA measured the Isopar™ L post-contactor concentration to be 25 mg/L, HPLC measured 39 mg/L of Modifier. For moderate-flow (0.54 gpm aqueous) conditions, SVOA measured the Isopar™ L postcontactor to be ~69 mg/L, while the HPLC measured 56 mg/L for Modifier. For high-flow (0.8 gpm aqueous) conditions, SVOA measured the Isopar™ L post-contactor to be 39 mg/L. The post-coalescer (pre-decanter) measurements by SVOA for Isopar™ L were all less than the analysis detection limit of 10 mg/L. The HPLC measured 18, 22 and 20 mg/L Modifier for the low, medium, and high-low rates respectively. In extraction, the quantity of pre-coalescer Isopar™ L carryover measured by SVOA was ~280-410 mg/L at low flow (4 gpm aqueous), ~400-450 mg/L at moderate flow (8 gpm aqueous), and ~480 mg/L at high flow (12 gpm aqueous). The amount of post coalescer (pre-decanter) Isopar™ L carryover measured by SVOA was less than 45 mg/L for all flow rates. HPLC results for Modifier were 182, 217 and 222 mg/L for the post-contactor low, medium and high flow rates. The post-coalescer (pre-decanter) samples were measured to contain 12, 10 and 22 mg/L Modifier for the low, medium, and high flow rates. The carryover results and droplet size measurements were used to determine the decanter performance utilizing the decanter model developed by the ARES Corporation. Results show for the targeted salt flow rate of approximately 8 gpm, that over 93% of the solvent carryover from stripping is predicted to be recovered and over 96% solvent carryover from extraction is predicted to be recovered. This translates to a predicted solvent carryover of <3 ppm from stripping and <20 ppm solvent carryover from extraction. This projected performance at MCU is expected to be well within the operating limits and the historical performance for the baseline BOBCalixC6 based solvent. Droplet-size data obtained by MicroTrac™ S3400 analyzer consistently shows that the droplet size post-oalescer is significantly greater than the post-contactor or pre-coalescer samples. Increased flow rates did not show a consistent impact to the droplet size results. For the extraction testing, droplet size analysis showed that the post-contactor and pre-coalescer samples were essentially the same. The mean droplet sizes post-coalescer were less than the mean droplet sizes pre-coalescer with a very slight upward trend in the mean droplet size as the flow rate was increased. This result is probably due to the method of sampling. The larger post-coalescer drops immediately rise to the surface after leaving the coalescer element. The downstream sampling point was horizontally in-line with the element and therefore would only capture those organic droplets well mixed in the flowing aqueous stream.« less

Polyethyleneimine-modified superparamagnetic Fe3O4 nanoparticles: An efficient, reusable and water tolerance nanocatalyst

NASA Astrophysics Data System (ADS)

Khoobi, Mehdi; Delshad, Tayebeh Modiri; Vosooghi, Mohsen; Alipour, Masoumeh; Hamadi, Hosein; Alipour, Eskandar; Hamedani, Majid Pirali; Sadat ebrahimi, Seyed Esmaeil; Safaei, Zahra; Foroumadi, Alireza; Shafiee, Abbas

2015-02-01

A novel magnetically separable catalyst was prepared based on surface modification of Fe3O4 magnetic nanoparticle (MNPs) with polyethyleneimine (PEI) via covalent bonding. [3-(2,3-Epoxypropoxy)propyl]trimethoxysilane (EPO) was used as cross linker to bond PEI on the surface of MNPs with permanent stability in contrast to PEI coating via electrostatic interactions. The synthesized catalyst was characterized by Fourier transform infrared (FT-IR), thermogravimetric analysis (TGA), X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and vibrating sample magnetometry (VSM). The catalyst show high efficiency for one-pot synthesis of 2-amino-3-cyano-4H-pyran derivatives via multi-component reaction (MCR). This procedure offers the advantages of green reaction media, high yield, short reaction time, easy purification of the products and simple recovery and reuse of the catalyst by simple magnetic decantation without significant loss of catalytic activity.

Methane potential of sterilized solid slaughterhouse wastes.

PubMed

Pitk, Peep; Kaparaju, Prasad; Vilu, Raivo

2012-07-01

The aim of the current study was to determine chemical composition and methane potential of Category 2 and 3 solid slaughterhouse wastes rendering products (SSHWRP) viz. melt, decanter sludge, meat and bone meal (MBM), technical fat and flotation sludge from wastewater treatment. Chemical analyses showed that SSHWRP were high in protein and lipids with total solids (TS) content of 96-99%. Methane yields of the SSHWRP were between 390 and 978 m(3) CH(4)/t volatile solids (VS)(added). Based on batch experiments, anaerobic digestion of SSHWRP from the dry rendering process could recover 4.6 times more primary energy than the energy required for the rendering process. Estonia has technological capacity to sterilize all the produced Category 2 and 3 solid slaughterhouse wastes (SSHW) and if separated from Category 1 animal by-products (ABP), it could be further utilized as energy rich input material for anaerobic digestion. Copyright © 2012 Elsevier Ltd. All rights reserved.

Crystals seen on CSF microscopy in a case of suspected subarachnoid haemorrhage

PubMed Central

Weiand, Daniel; Hanning, Ian; Mouhamadou, Moussa; Wearmouth, Debbie

2015-01-01

Although crystals are rarely identified on cerebrospinal fluid (CSF) microscopy, their presence can be of significant diagnostic value. We report a case of oxalate crystals seen on CSF microscopy of a 43-year-old woman. The patient presented with headaches, nausea and vomiting. CT of the head showed a small focus of hyper-density, suspicious of haemorrhage, in the right side of the pontine cistern. CSF cell count was within the normal range. Although no organisms were seen on microscopy, copious oxalate crystals were seen. The same crystals were seen on microscopy of CSF collected in a fluoride oxalate container used for glucose analysis. A follow-up contrast-enhanced CT angiogram did not demonstrate any abnormalities. It transpired that excess CSF had been collected into a fluoride oxalate container. This had subsequently been decanted into a plain container for microbiological analysis. Correct specimen collection should be emphasised when teaching lumbar puncture technique. PMID:26139652

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bunster, Claudio; Max-Planck-Institut fuer Gravitationsphysik; Henneaux, Marc

There exists a formulation of the Maxwell theory in terms of two vector potentials, one electric and one magnetic. The action is then manifestly invariant under electric-magnetic duality transformations, which are rotations in the two-dimensional internal space of the two potentials, and local. We ask the question: Can duality be gauged? The only known and battle-tested method of accomplishing the gauging is the Noether procedure. In its decanted form, it amounts to turning on the coupling by deforming the Abelian gauge group of the free theory, out of whose curvatures the action is built, into a non-Abelian group which becomesmore » the gauge group of the resulting theory. In this article, we show that the method cannot be successfully implemented for electric-magnetic duality. We thus conclude that, unless a radically new idea is introduced, electric-magnetic duality cannot be gauged. The implication of this result for supergravity is briefly discussed.« less

Protein Concentrate Production from Thin Stillage.

PubMed

Ratanapariyanuch, Kornsulee; Shim, Youn Young; Emami, Shahram; Reaney, Martin J T

2016-12-21

Two-stage fermentation (TSF) of saccharified wheat with a consortium of endemic lactobacilli produced CO 2 and induced colloid separation of fermented solution to produce a protein concentrate (PC). Protein-rich slurry (50%, db) was obtained by decanting solution or skimming floating material during or after TSF. Washing and drying processes were explored to improve protein content, extend storage life of slurry, and yield converted stillage for compound recovery. Centrifuging and washing slurry afforded a PC and clarified solution. PC protein content increased to 60% (w/w, db). The PC was dried in a spray dryer or drum dryer or tray dryer. Dried PC water activity ranged 0.23-0.30. The dried PC lysine content was low, but lysine availability (95%) was excellent. Liquid from TSF and washing was readily microfiltered. Mass recovery of protein, glycerol, 1,3-propanediol, lactic acid, acetic acid, and glycerylphosphorylcholine from combined TSF, washing, and filtration were 66, 76, 72, 77, 74, and 84%, respectively.

Detection of mast cell secretion by using surface enhanced Raman scattering

NASA Astrophysics Data System (ADS)

Li, Juan; Li, Ren; Zheng, Liqin; Wang, Yuhua; Xie, Shusen; Lin, Juqiang

2016-10-01

Acupuncture can cause a remarkable increase in degranulation of the mast cells, which has attracted the interest of researchers since the 1980s. Surface-enhanced Raman scattering (SERS) could obtain biochemical information with high sensitivity and specificity. In this study, SERS was used to detect the degree of degranulation of mast cells according to different incubate time. Mast cells was incubated with culture medium for 0 h, 12 h and 24 h, then centrifuge the culture medium, decant the supernatant, and discard the mast cell. SERS was performed to obtain the biochemical fingerprinting signatures of the centrifuged medium. The spectra data are then analyzed by spectral peaks attribution and the principal component analysis (PCA). The measured Raman spectra of the two groups were separated well by PCA. It indicated that mast cells had secreted some substances into cultured medium though degranulation did not happen.

Method of producing a colloidal fuel from coal and a heavy petroleum fraction

DOEpatents

Longanbach, James R.

1983-08-09

A method is provided for combining coal as a colloidal suspension within a heavy petroleum fraction. The coal is broken to a medium particle size and is formed into a slurry with a heavy petroleum fraction such as a decanted oil having a boiling point of about 300.degree.-550.degree. C. The slurry is heated to a temperature of 400.degree.-500.degree. C. for a limited time of only about 1-5 minutes before cooling to a temperature of less than 300.degree. C. During this limited contact time at elevated temperature the slurry can be contacted with hydrogen gas to promote conversion. The liquid phase containing dispersed coal solids is filtered from the residual solids and recovered for use as a fuel or feed stock for other processes. The residual solids containing some carbonaceous material are further processed to provide hydrogen gas and heat for use as required in this process.

Evaluation of co-cokes from bituminous coal with vacuum resid or decant oil, and evaluation of anthracites, as precursors to graphite

NASA Astrophysics Data System (ADS)

Nyathi, Mhlwazi S.

2011-12-01

Graphite is utilized as a neutron moderator and structural component in some nuclear reactor designs. During the reactor operaction the structure of graphite is damaged by collision with fast neutrons. Graphite's resistance to this damage determines its lifetime in the reactor. On neutron irradiation, isotropic or near-isotropic graphite experiences less structural damage than anisotropic graphite. The degree of anisotropy in a graphite artifact is dependent on the structure of its precursor coke. Currently, there exist concerns over a short supply of traditional precursor coke, primarily due to a steadily increasing price of petroleum. The main goal of this study was to study the anisotropic and isotropic properties of graphitized co-cokes and anthracites as a way of investigating the possibility of synthesizing isotropic or near-isotropic graphite from co-cokes and anthracites. Demonstrating the ability to form isotropic or near-isotropic graphite would mean that co-cokes and anthracites have a potential use as filler material in the synthesis of nuclear graphite. The approach used to control the co-coke structure was to vary the reaction conditions. Co-cokes were produced by coking 4:1 blends of vacuum resid/coal and decant oil/coal at temperatures of 465 and 500 °C for reaction times of 12 and 18 hours under autogenous pressure. Co-cokes obtained were calcined at 1420 °C and graphitized at 3000 °C for 24 hours. Optical microscopy, X-ray diffraction, temperature-programmed oxidation and Raman spectroscopy were used to characterize the products. It was found that higher reaction temperature (500 °C) or shorter reaction time (12 hours) leads to an increase in co-coke structural disorder and an increase in the amount of mosaic carbon at the expense of textural components that are necessary for the formation of anisotropic structure, namely, domains and flow domains. Characterization of graphitized co-cokes showed that the quality, as expressed by the degree of graphitization and crystallite dimensions, of the final product is dependent on the nature of the precursor co-coke. The methodology for studying anthracites was to select two anthracites on basis of rank, PSOC1515 being semi-anthracite and DECS21 anthracite. The selected anthracites were graphitized, in both native and demineralized states, under the same conditions as co-cokes. Products obtained from DECS21 showed higher degrees of graphitization and larger crystallite dimensions than products obtained from PSOC1515. Demineralization of anthracites served to increase the degree of graphitization, indicating that the minerals contained in these anthracites have no graphitization-enhancing ability. A larger crystallite length for products obtained from native versions, compared to demineralized versions, was attributed to a formation and decomposition of a silicon carbide during graphitization of native versions. In order to examine the anisotropic and isotropic properties, nuclear-grade graphite samples obtained from Oak Ridge National Laboratory (ORNL) and commercial graphite purchased from Fluka were characterized under similar conditions as graphitized co-cokes and anthracites. These samples served as representatives of "two extremes", with ORNL samples being the isotropic end and commercial graphite being the anisotropic end. Through evaluating relationships between structural parameters, it was observed that graphitized co-cokes are situated, structurally, somewhere between the "two extremes", whereas graphitized anthracites are closer to the anisotropic end. Basically, co-cokes have a better potential than anthracites to transform to isotropic or near-isotropic graphite upon graphitization. By co-coking vacuum resid/coal instead of decant oil/coal or using 500 °C instead of 465 °C, a shift away from commercial graphite towards ORNL samples was attained. Graphitizing a semi-anthracite or demineralizing anthracites before graphitization also caused a shift towards ORNL samples.

Method of producing a colloidal fuel from coal and a heavy petroleum fraction. [partial liquefaction of coal in slurry, filtration and gasification of residue

DOEpatents

Longanbach, J.R.

1981-11-13

A method is provided for combining coal as a colloidal suspension within a heavy petroleum fraction. The coal is broken to a medium particle size and is formed into a slurry with a heavy petroleum fraction such as a decanted oil having a boiling point of about 300 to 550/sup 0/C. The slurry is heated to a temperature of 400 to 500/sup 0/C for a limited time of only about 1 to 5 minutes before cooling to a temperature of less than 300/sup 0/C. During this limited contact time at elevated temperature the slurry can be contacted with hydrogen gas to promote conversion. The liquid phase containing dispersed coal solids is filtered from the residual solids and recovered for use as a fuel or feed stock for other processes. The residual solids containing some carbonaceous material are further processed to provide hydrogen gas and heat for use as required in this process.

Sealed-bladdered chemical processing method and apparatus

DOEpatents

Harless, D. Phillip

1999-01-01

A method and apparatus which enables a complete multi-stepped chemical treatment process to occur within a single, sealed-bladdered vessel 31. The entire chemical process occurs without interruption of the sealed-bladdered vessel 31 such as opening the sealed-bladdered vessel 31 between various steps of the process. The sealed-bladdered vessel 31 is loaded with a batch to be dissolved, treated, decanted, rinsed and/or dried. A pressure filtration step may also occur. The self-contained chemical processing apparatus 32 contains a sealed-bladder 32, a fluid pump 34, a reservoir 20, a compressed gas inlet, a vacuum pump 24, and a cold trap 23 as well as the associated piping 33, numerous valves 21,22,25,26,29,30,35,36 and other controls associated with such an apparatus. The claimed invention allows for dissolution and/or chemical treatment without the operator of the self-contained chemical processing apparatus 38 coming into contact with any of the process materials.

Concentrations and forms of heavy metals around two ore processing sites in Katanga, Democratic Republic of Congo

NASA Astrophysics Data System (ADS)

Mees, F.; Masalehdani, M. N. N.; De Putter, T.; D'Hollander, C.; Van Biezen, E.; Mujinya, B. B.; Potdevin, J. L.; Van Ranst, E.

2013-01-01

The concentration of heavy metals and the forms in which they occur were determined for tailings and derived deposits of two major processing sites of Cu-Co and Cu-Zn-(Pb) ores in the Katanga Copperbelt (Kipushi, Likasi). They were studied by a combination of methods, focussed on the nature of water- and EDTA-extractable compounds, the mineralogical composition of tailings and associated secondary minerals, and textural features of metal-bearing efflorescences. For the Kipushi area, sulfide minerals in tailings of decantation basins are identified as the source of extractable metals they contain, but input from an external source rather than local oxidation of substrate components is responsible for high levels of contamination in the Likasi area. Contaminated areas around Likasi are characterized by an abundance of Mg-sulfate efflorescences with high concentrations of cobalt and other metals, acting as an important vector for further dispersion of contaminants by wind and water.

Old wine in new bottles: decanting systemic family process research in the era of evidence-based practice.

PubMed

Rohrbaugh, Michael J

2014-09-01

Social cybernetic (systemic) ideas from the early Family Process era, though emanating from qualitative clinical observation, have underappreciated heuristic potential for guiding quantitative empirical research on problem maintenance and change. The old conceptual wines we have attempted to repackage in new, science-friendly bottles include ironic processes (when "solutions" maintain problems), symptom-system fit (when problems stabilize relationships), and communal coping (when we-ness helps people change). Both self-report and observational quantitative methods have been useful in tracking these phenomena, and together the three constructs inform a team-based family consultation approach to working with difficult health and behavior problems. In addition, a large-scale, quantitatively focused effectiveness trial of family therapy for adolescent drug abuse highlights the importance of treatment fidelity and qualitative approaches to examining it. In this sense, echoing the history of family therapy research, our experience with juxtaposing quantitative and qualitative methods has gone full circle-from qualitative to quantitative observation and back again. © 2014 FPI, Inc.

Old Wine in New Bottles: Decanting Systemic Family Process Research in the Era of Evidence-Based Practice†

PubMed Central

Rohrbaugh, Michael J.

2015-01-01

Social cybernetic (systemic) ideas from the early Family Process era, though emanating from qualitative clinical observation, have underappreciated heuristic potential for guiding quantitative empirical research on problem maintenance and change. The old conceptual wines we have attempted to repackage in new, science-friendly bottles include ironic processes (when “solutions” maintain problems), symptom-system fit (when problems stabilize relationships), and communal coping (when we-ness helps people change). Both self-report and observational quantitative methods have been useful in tracking these phenomena, and together the three constructs inform a team-based family consultation (FAMCON) approach to working with difficult health and behavior problems. In addition, a large-scale, quantitatively focused effectiveness trial of family therapy for adolescent drug abuse highlights the importance of treatment fidelity and qualitative approaches to examining it. In this sense, echoing the history of family therapy research, our experience with juxtaposing quantitative and qualitative methods has gone full circle – from qualitative to quantitative observation and back again. PMID:24905101

Pig slurry acidification and separation techniques affect soil N and C turnover and N2O emissions from solid, liquid and biochar fractions.

PubMed

Gómez-Muñoz, B; Case, S D C; Jensen, L S

2016-03-01

The combined effects of pig slurry acidification, subsequent separation techniques and biochar production from the solid fraction on N mineralisation and N2O and CO2 emissions in soil were investigated in an incubation experiment. Acidification of pig slurry increased N availability from the separated solid fractions in soil, but did not affect N2O and CO2 emissions. However acidification reduced soil N and C turnover from the liquid fraction. The use of more advanced separation techniques (flocculation and drainage > decanting centrifuge > screw press) increased N mineralisation from acidified solid fractions, but also increased N2O and CO2 emissions in soil amended with the liquid fraction. Finally, the biochar production from the solid fraction of pig slurry resulted in a very recalcitrant material, which reduced N and C mineralisation in soil compared to the raw solid fractions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Target guided synthesis using DNA nano-templates for selectively assembling a G-quadruplex binding c-MYC inhibitor

NASA Astrophysics Data System (ADS)

Panda, Deepanjan; Saha, Puja; Das, Tania; Dash, Jyotirmayee

2017-07-01

The development of small molecules is essential to modulate the cellular functions of biological targets in living system. Target Guided Synthesis (TGS) approaches have been used for the identification of potent small molecules for biological targets. We herein demonstrate an innovative example of TGS using DNA nano-templates that promote Huisgen cycloaddition from an array of azide and alkyne fragments. A G-quadruplex and a control duplex DNA nano-template have been prepared by assembling the DNA structures on gold-coated magnetic nanoparticles. The DNA nano-templates facilitate the regioselective formation of 1,4-substituted triazole products, which are easily isolated by magnetic decantation. The G-quadruplex nano-template can be easily recovered and reused for five reaction cycles. The major triazole product, generated by the G-quadruplex inhibits c-MYC expression by directly targeting the c-MYC promoter G-quadruplex. This work highlights that the nano-TGS approach may serve as a valuable strategy to generate target-selective ligands for drug discovery.

Mesophilic co-digestion of dairy manure and lipid rich solid slaughterhouse wastes: process efficiency, limitations and floating granules formation.

PubMed

Pitk, Peep; Palatsi, Jordi; Kaparaju, Prasad; Fernández, Belén; Vilu, Raivo

2014-08-01

Lipid and protein rich solid slaughterhouse wastes are attractive co-substrates to increase volumetric biogas production in co-digestion with dairy manure. Addition of decanter sludge (DS), containing 42.2% of lipids and 35.8% of proteins (total solids basis), up to 5% of feed mixture resulted in a stable process without any indication of long chain fatty acids (LCFA) or free ammonia (NH3) inhibition and in 3.5-fold increase of volumetric biogas production. Contrary, only lipids addition as technical fat (TF) at over 2% of feed mixture resulted in formation of floating granules (FG) and process efficiency decrease. Formed FG had low biodegradability and its organic part was composed of lipids and calcium salts of LCFAs. Anaerobic digestion process intentionally directed to FG formation, could be a viable option for mitigation and control of lipids overload and derived LCFA inhibition. Copyright © 2014 Elsevier Ltd. All rights reserved.

Electricity production and microbial biofilm characterization in cellulose-fed microbial fuel cells.

PubMed

Ren, Z; Steinberg, L M; Regan, J M

2008-01-01

Converting biodegradable materials into electricity, microbial fuel cells (MFCs) present a promising technology for renewable energy production in specific applications. Unlike typical soluble substrates that have been used as electron donors in MFC studies, cellulose is unique because it requires a microbial consortium that can metabolize both an insoluble electron donor (cellulose) and electron acceptor (electrode). In this study, electricity generation and the microbial ecology of cellulose-fed MFCs were analyzed using a defined co-culture of Clostridium cellulolyticum and Geobacter sulfurreducens. Fluorescent in situ hybridization and quantitative PCR showed that when particulate MN301 cellulose was used as sole substrate, most Clostridium cells were found adhered to cellulose particles in suspension, while most Geobacter cells were attached to the electrode. By comparison, both bacteria resided in suspension and biofilm samples when soluble carboxymethyl cellulose was used. This distinct function-related distribution of the bacteria suggests an opportunity to optimize reactor operation by settling cellulose and decanting supernatant to extend cellulose hydrolysis and improve cellulose-electricity conversion. (c) IWA Publishing 2008.

Disinfection By-Product Formation and Mitigation Strategies in Point-of-Use Chlorination with Sodium Dichloroisocyanurate in Tanzania

PubMed Central

Lantagne, Daniele S.; Cardinali, Fred; Blount, Ben C.

2010-01-01

Almost a billion persons lack access to improved drinking water, and diarrheal diseases cause an estimated 1.87 million deaths per year. Sodium dichloroisocyanurate (NaDCC) tablets are widely recommended for household water treatment to reduce diarrhea. Because NaDCC is directly added to untreated water sources, concerns have been raised about the potential health impact of disinfection by-products. This study investigated trihalomethane (THM) production in water from six sources used for drinking (0.6–888.5 nephelometric turbidity units) near Arusha, Tanzania. No sample collected at 1, 8, and 24 hours after NaDCC addition exceeded the World Health Organization guideline values for either individual or total THMs. Ceramic filtration, sand filtration, cloth filtration, and settling and decanting were not effective mitigation strategies to reduce THM formation. Chlorine residual and THM formation were not significantly different in NaDCC and sodium hypochlorite treatment. Household chlorination of turbid and non-turbid waters did not create THM concentrations that exceeded health risk guidelines. PMID:20595492

Polyelectrolyte flocculation of grain stillage for improved clarification and water recovery within bioethanol production facilities.

PubMed

Menkhaus, Todd J; Anderson, Jason; Lane, Samuel; Waddell, Evan

2010-04-01

Polyelectrolytes were investigated for flocculation of a corn whole stillage stream to improve solid-liquid clarification operations and reduce downstream utility requirements for evaporation and drying within a bioethanol process. Despite a negative zeta potential for the stillage solids, an anionic polyelectrolyte was found to provide the best flocculation. At the optimal dosage of 1.1mg polymer/g dry suspended solids, an anionic flocculant provided a clarified stream with only 0.15% w/w suspended solids (equivalent to a total dissolved solid to total suspended solid ratio greater than 40, and a viscosity reduction of 39% compared to an unflocculated "clarified" stream). The resulting solids cake had greater than 40% w/w solids, and more than 80% water recovery was found in the clarified stream. Addition of flocculant improved filtration flux by six fold and/or would allow for up to a 4-times higher flow rate if using a decanting centrifuge for clarification of corn stillage. Copyright 2009 Elsevier Ltd. All rights reserved.

Study of virgin olive oil clarification by settling under dynamic conditions.

PubMed

Gila, Abraham; Bejaoui, Mohamed Aymen; Beltrán, Gabriel; Aguilera, María Paz; Jiménez, Antonio

2018-04-16

Vertical centrifugation is the main method for virgin olive oil (VOO) clarification. However, in recent years, settling tanks are also being used to clarify the oils from decanters. They can operate under static or dynamic conditions. In this work, vertical centrifugation and settling under dynamic conditions for VOO clarification and their effects on VOO characteristics were compared. VOO quality parameters were not affected by the clarification systems studied. The vertical centrifugal separator (VCS) showed higher clarification efficiency, giving clarified oils with higher phenol content and better sensory characteristics. VOOs clarified by dynamic settling showed notable losses of phenols and worse sensory characteristics, since the tank purge system was not efficient, with most of the impurities remaining in the tanks. The VCS with minimal water addition is a quick operation with low water consumption and is a better option to produce VOOs of improved quality, especially in terms of longer shelf life and preservation of positive sensory notes. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Influence of vegetation on the infilling of a macrotidal embayment: examples from salt marshes and shingle spit of the Baie de Somme (North France)

NASA Astrophysics Data System (ADS)

Le Bot, Sophie; Forey, Estelle; Lafite, Robert; Langlois, Estelle

2015-04-01

As many estuaries in the English Channel, the Baie de Somme is currently filling with a mean seabed elevation between 1.3 and 1.8 cm/yr. Embankments and polders, as well as sea level rise, increase this natural accretion process, which leads to important modifications of environment uses. Interactions between vegetation and sediment dynamics constitute a key-point to consider, in order to better understand the infilling processes in estuaries. To estimate the effect of vegetation on these processes, two particular environments have been studied in the bay: (i) the mid salt marsh covered with Halimione portulacoides, associated with a silty sedimentation, and (ii) the shingle spit, that closes the bay from the South, on which the sea kale (Crambe maritime), a protected pioneer species, develops. Salt marshes progress with a rate of 5-10 m/yr (mean value calculated on the 1947-2011 period). Sedimentological analysis have been conducted on 9 cores (50cm long) collected in three Halimione communities of the bay. They are associated with a silty-dominated (38-84 micrometer) sedimentation under the influence of decantation processes. Rhythmicity is observed in the sedimentation, due to the repetition of a two-layer pattern, that includes a dark layer composed of vegetal rests and that would represent annual sedimentation. Annual sedimentation rates (0.7 to 5.8 cm/yr) are consistent with mean values previously recorded. The shingle spit progresses to the North under the influence of the littoral drift at a rate of 7 m/yr (mean value calculated on the 1947-2011 period). Sea kales are observed on parts formed since several years, above the level of the highest astronomical tides. TLS surveys and sedimentation bars have allowed to measure erosion/sedimentation volumes at the scale of the spit and of sea kale individuals, during spring 2013. Individuals of this species facilitate the trapping of sand, transported by winds from the intertidal flats. Sea kale thus contributes to the maintenance of sand at the surface of the spit during spring (development period of sea kales) and, probably to the progressive silting up of the spit on a longer-term. Thus, sea kale indirectly favours the filling of the bay through the building up and consolidation of the spit that, in turn, enhances sheltered conditions increasing the part of decantation processes in the sedimentation in the bay. (financial support by Région Haute-Normandie and Réseau d'Observation du Littoral Normand et Picard, ROLNP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raszewski, F; Tommy Edwards, T; David Peeler, D

Sludge Batch 4 (SB4) is currently being processed in the Defense Waste Processing Facility (DWPF) using Frit 510. The slurry pumps in Tank 40 are experiencing in-leakage of bearing water, which is causing the sludge slurry feed in Tank 40 to become dilute at a rapid rate. Currently, the DWPF is removing this dilution water by performing caustic boiling during the Sludge Receipt and Adjustment Tank (SRAT) cycle. In order to alleviate prolonged SRAT cycle times that may eventually impact canister production rates, decant scenarios of 100, 150, and 200 kilogallons of supernate were proposed for Tank 40 during themore » DWPF March outage. Based on the results of the preliminary assessment issued by the Savannah River National Laboratory (SRNL), the Liquid Waste Organization (LWO) issued a Technical Task Request (TTR) for SRNL to (1) perform a more detailed evaluation using updated SB4 compositional information and (2) assess the viability of Frit 510 and determine any potential impacts on the SB4 system. As defined in the TTR, LWO requested that SRNL validate the sludge--only SB4 flowsheet and the coupled operations flowsheet using the 100K gallon decant volume as well as the addition of 3 wt% sodium on a calcined oxide basis. Approximately 12 historical glasses were identified during a search of the ComProTM database that are located within at least one of the five glass regions defined by the proposed SB4 flowsheet options. While these glasses meet the requirements of a variability study there was some concern that the compositional coverage did not adequately bound all cases. Therefore, SRNL recommended that a supplemental experimental variability study be performed to support the various SB4 flowsheet options that may be implemented for future SB4 operations in DWPF. Eighteen glasses were selected based on nominal sludge projections representing the current as well as the proposed flowsheets over a WL interval of interest to DWPF (32-42%). The intent of the experimental portion of the variability study is to demonstrate that the glasses of the Frit 510-modified SB4 compositional region (Cases No.1-5) are both acceptable relative to the Environmental Assessment (EA) reference glass and predictable by the current DWPF process control models for durability. Frit 510 is a viable option for the processing of SB4 after a Tank 40 decant and the addition of products from the Actinide Removal Process (ARP). The addition of ARP did not have any negative impacts on the acceptability and predictability of the variability study glasses. The results of the variability study indicate that all of the study glasses (both quenched and centerline canister cooled (ccc)) have normalized releases for boron that are well below the reference EA glass (16.695 g/L). The durabilities of all of the study glasses are predictable using the current Product Composition Control System (PCCS) durability models with the exception of SB4VAR24ccc (Case No.2 at 41%). PCCS is not applicable to non-homogeneous glasses (i.e. glasses containing crystals such as acmite and nepheline), thus SB4VAR24ccc should not be predictable as it contains nepheline. The presence of nepheline has been confirmed in both SB4VAR13ccc and SB4VAR24ccc by X-ray diffraction (XRD). These two glasses are the first results which indicate that the current nepheline discriminator value of 0.62 is not conservative. The nepheline discriminator was implemented into PCCS for SB4 based on the fact that all of the historical glasses evaluated with nepheline values of 0.62 or greater did not contain nepheline via XRD analysis. Although these two glasses do cause some concern over the use of the 0.62 nepheline value for future DWPF glass systems, the impact to the current SB4 system is of little concern. More specifically, the formation of nepheline was observed in glasses targeting 41 or 42% WL. Current processing of the Frit 510-SB4 system in DWPF has nominally targeted 34% WL. For the SB4 variability study glasses targeting these lower WLs, nepheline formation was not observed and the minimal difference in PCT response between quenched and ccc versions supported its absence.« less

Remediation of coal mining wastewaters using chitosan microspheres.

PubMed

Geremias, R; Pedrosa, R C; Benassi, J C; Fávere, V T; Stolberg, J; Menezes, C T B; Laranjeira, M C M

2003-12-01

This study aimed to evaluate the potential use of chitosan and chitosan/poly(vinylalcohol) microspheres incorporating with tetrasulphonated copper (II) phthalocyanine (CTS/PVA/TCP) in the remediation of coal mining wastewaters. The process was monitored by toxicity tests both before and after adsorption treatments with chitosan and microspheres. Physicochemical parameters, including pH and trace-metal concentration, as well as bioindicators of water pollution were used to that end. Wastewater samples colleted from drainage of underground coal mines, decantation pools, and contaminated rivers were scrutinized. Acute toxicity tests were performed using the Brine Shrimp Test (BST) in order to evaluate the remediation efficiency of different treatments. The results showed that the pH of treated wastewater samples were improved to values close to neutrality. Chitosan treatments were also effective in removing trace-metals. Pre-treatment with chitosan followed by microsphere treatment (CTS/PVA/TCP) was more effective in decreasing toxicity than the treatment using only chitosan. This was probably due to the elimination of pollutants other than trace-metals. Thus, the use of chitosan and microspheres is an adequate alternative towards remediation of water pollution from coal mining.

Effects of intermittent aeration periods on a structured-bed reactor continuously fed on the post-treatment of sewage anaerobic effluent.

PubMed

Silva, Bruno Garcia; Damianovic, Márcia Helena Rissato Zamariolli; Foresti, Eugenio

2018-04-20

This study assessed the simultaneous nitrification and denitrification processes and remaining organic matter removal from anaerobic reactor effluent treating wastewater in a single reactor. A structured-bed reactor, with polyurethane foam as support media, was subjected to intermittent aeration and effluent recirculation. Aerated/non-aerated periods varied in the range of 2/1-1/3 h. The chemical oxygen demand (COD) in the effluent remained between 26 and 42 mg L -1 throughout all the aeration conditions. Aeration periods of 1/2 h removed 80 and 26% of Total Kjeldahl Nitrogen and Total Nitrogen, respectively. A low solid production was observed during the 300 days of operation, resulting in a solid retention time of 139 days. The results indicate that the non-aerated periods generated alkalinity that favored nitrification, maintaining low COD concentrations in the effluent. The structured bed reactor presented a low solid production and effluent loss below 20 mgSSV L -1 , similar to concentrations obtained in secondary decanters.

Method for the recovery of silver from waste photographic fixer solutions

DOEpatents

Posey, F.A.; Palko, A.A.

The method of the present invention is directed to the recovery of silver from spent photographic fixer solutions and for providing an effluent essentially silver-free that is suitable for discharge into commercial sewage systems. The present method involves the steps of introducing the spent photographic fixer solution into an alkaline hypochlorite solution. The oxidizing conditions of the alkaline hypochlorite solution are maintained during the addition of the fixer solution so that the silver ion complexing agents of thiosulfate and sulfite ions are effectively destroyed. Hydrazine monohydrate is then added to the oxidizing solution to form a reducing solution to effect the formation of a precipitate of silver which can be readily removed by filtration of decanting. Experimental tests indicate that greater than 99.99% of the original silver in the spent photographic fixer can be efficiently removed by practicing the present method. Also, the chemical and biological oxygen demand of the remaining effluent is significantly reduced so as to permit the discharge thereof into sewage systems at levels in compliance with federal and state environmental standards.

Synthesis and characterization of the NiFe2O4@TEOS-TPS@Ag nanocomposite and investigation of its antibacterial activity

NASA Astrophysics Data System (ADS)

Allafchian, Ali R.; Jalali, S. A. H.; Amiri, R.; Shahabadi, Sh.

2016-11-01

In this study, the NiFe2O4 was embedded in (3-mercaptopropyl) trimethoxysilane (TPS) and tetraethyl orthosilicate (TEOS) using the sol-gel method. These compounds were used as the support of Ag nanoparticles (Ag NPs). The NiFe2O4@TEOS-TPS@Ag nanocomposites were obtained with the development of bonding between the silver atoms of Ag NPs and the sulfur atoms of TPS molecule. Field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) were used for the characterization of the Ag nanocomposites. Also, the magnetic properties of these nanocomposites were studied by using a vibrating sample magnetometer (VSM) technique. The disk diffusion, minimum inhibition concentration (MIC) and minimum bactericidal concentrations (MBC) tests were used for the investigation of the antibacterial effect of this nanocomposite against bacterial strains. The synthesized nanocomposite presented high reusability and good antibacterial activity against gram-positive and gram-negative bacteria. Remarkably, this nanocomposite could be easily removed from the disinfected media by magnetic decantation.

Membrane thickening aerobic digestion processes.

PubMed

Woo, Bryen

2014-01-01

Sludge management accounts for approximately 60% of the total wastewater treatment plant expenditure and laws for sludge disposal are becoming increasingly stringent, therefore much consideration is required when designing a solids handling process. A membrane thickening aerobic digestion process integrates a controlled aerobic digestion process with pre-thickening waste activated sludge using membrane technology. This process typically features an anoxic tank, an aerated membrane thickener operating in loop with a first-stage digester followed by second-stage digestion. Membrane thickening aerobic digestion processes can handle sludge from any liquid treatment process and is best for facilities obligated to meet low total phosphorus and nitrogen discharge limits. Membrane thickening aerobic digestion processes offer many advantages including: producing a reusable quality permeate with minimal levels of total phosphorus and nitrogen that can be recycled to the head works of a plant, protecting the performance of a biological nutrient removal liquid treatment process without requiring chemical addition, providing reliable thickening up to 4% solids concentration without the use of polymers or attention to decanting, increasing sludge storage capacities in existing tanks, minimizing the footprint of new tanks, reducing disposal costs, and providing Class B stabilization.

Radiation treatment of molasses

NASA Astrophysics Data System (ADS)

Rodríguez, A. S.; Serrano G., J.; Lara R., O.; Reyes L., J.

Molasses are a by-product of the sugar industry. Their annual production in México in around 1 million tons and are mainly used as a complement for animal feeding and for the production of alcohols. Their value is relatively low compared with another chemicals. When molasses are irradiated with gamma radiation or accelerated electrons, in presence of nitric acid and oxygen, it is obtained oxalic acid and several polymeric compounds. In both cases, the same products are obtained, but the yield is greater with electrons. It has been studied the effect of dose and dose rate in the yields. As example, when mixtures of molasses-nitric acid, with an initial concentration of 26% of total sugar reductors, are irradiated with 1.0 MeV electrons, in a continuous flow reactor, at 0.11 {Gy}/{sec} to a total dose of 30 KGy, the oxalic acid yield is around 44% of the total chemical reductors used. The separations of the radiolytic products was made by successive decantations and concentrations, and purified by recristallizations. From the analytical information, the minimal formula were calculated for the acid product and the polymeric compounds.

Method for the recovery of silver from waste photographic fixer solutions

DOEpatents

Posey, Franz A.; Palko, Aloysius A.

1984-01-01

The method of the present invention is directed to the recovery of silver from spent photographic fixer solutions and for providing an effluent essentially silver-free that is suitable for discharge into commercial sewage systems. The present method involves the steps of introducing the spent photographic fixer solution into an alkaline hypochlorite solution. The oxidizing conditions of the alkaline hypochlorite solution are maintained during the addition of the fixer solution so that the silver ion complexing agents of thiosulfate and sulfite ions are effectively destroyed. Hydrazine monohydrate is then added to the oxidizing solution to form a reducing solution to effect the formation of a precipitate of silver which can be readily removed by filtration or decanting. Experimental tests indicate that greater than 99.99% of the original silver in the spent photographic fixer can be efficiently removed by practicing the present method. Also, the chemical and biological oxygen demand of the remaining effluent is significantly reduced so as to permit the discharge thereof into sewage systems at levels in compliance with federal and state environmental standards.

A simple method for collecting eggs of taeniid cestodes from fresh, frozen or ethanol-fixed segments.

PubMed

Takemoto, Y; Negita, T; Ohnishi, K; Suzuki, M; Ito, A

1995-04-01

A simple method was devised for collecting eggs of Taenia taeniaeformis and T. saginata. All gravid segments, either fresh or frozen or 70% ethanol-fixed, were gently scraped using a pestle on a 150 mesh stainless steel sieve. Eggs and tissue debris were washed out all together with mouse tonicity phosphate buffered saline (MTPBS) through the 150 mesh sieve into a glass beaker. Egg suspension with a huge amount of tissue debris in MTPBS was centrifuged 5 min at 3000 r.p.m. (x 1600 g) and the pellet of eggs and tissue debris was resuspended with 1 vol. of MTPBS and 2 vol. of Percoll (Pharmacia) and centrifuged 60 min at 3000 r.p.m. More than 90% of eggs sedimented in the pellet. The supernatant covered with tissue debris was decanted, and the egg pellet was resuspended and centrifuged several times with MTPBS to remove Percoll. It is suggested that this simple method may prove useful for preparation of eggs of biohazardous taeniid cestodes, such as Taenia solium and Echinococcus spp.

Treatment of crystallized-fruit wastewater by UV-A LED photo-Fenton and coagulation-flocculation.

PubMed

Rodríguez-Chueca, Jorge; Amor, Carlos; Fernandes, José R; Tavares, Pedro B; Lucas, Marco S; Peres, José A

2016-02-01

This work reports the treatment of crystallized-fruit effluents, characterized by a very low biodegradability (BOD5/COD <0.19), through the application of a UV-A LED photo-Fenton process. Firstly, a Box-Behnken design of Response Surface Methodology was applied to achieve the optimal conditions for the UV-A LED photo-Fenton process, trying to maximize the efficiency by saving chemicals and time. Under the optimal conditions ([H2O2] = 5459 mg/L; [Fe(3+)] = 286 mg/L; time >180 min), a COD removal of 45, 64 and 74% was achieved after 360 min, using an irradiance of 23, 70 and 85 W/m(2) respectively. Then a combination of UV-A LED photo-Fenton with coagulation-flocculation-decantation attained a higher COD removal (80%), as well as almost total removal of turbidity (99%) and total suspended solids (95%). Subsequent biodegradability of treated effluents increased, allowing the application of a biological treatment step after the photochemical/CFD with 85 W/m(2). Copyright © 2015 Elsevier Ltd. All rights reserved.

Decomposition Mechanism and Decomposition Promoting Factors of Waste Hard Metal for Zinc Decomposition Process (ZDP)

NASA Astrophysics Data System (ADS)

Pee, J. H.; Kim, Y. J.; Kim, J. Y.; Seong, N. E.; Cho, W. S.; Kim, K. J.

2011-10-01

Decomposition promoting factors and decomposition mechanism in the zinc decomposition process of waste hard metals which are composed mostly of tungsten carbide and cobalt were evaluated. Zinc volatility amount was suppressed and zinc steam pressure was produced in the reaction graphite crucible inside an electric furnace for ZDP. Reaction was done for 2 hrs at 650 °C, which 100 % decomposed the waste hard metals that were over 30 mm thick. As for the separation-decomposition of waste hard metals, zinc melted alloy formed a liquid composed of a mixture of γ-β1 phase from the cobalt binder layer (reaction interface). The volume of reacted zone was expanded and the waste hard metal layer was decomposed-separated horizontally from the hard metal. Zinc used in the ZDP process was almost completely removed-collected by decantation and volatilization-collection process at 1000 °C. The small amount of zinc remaining in the tungsten carbide-cobalt powder which was completely decomposed was fully removed by using phosphate solution which had a slow cobalt dissolution speed.

Influence of convection on microstructure

NASA Technical Reports Server (NTRS)

Wilcox, William R.; Eisa, Gaber Faheem; Chandrasekhar, S.; Larrousse, Mark; Banan, Mohsen

1988-01-01

The influence was studied of convection during directional solidification on the resulting microstructure of eutectics, specifically lead/tin and manganese/bismuth. A theory was developed for the influence of convection on the microstructure of lamellar and fibrous eutectics, through the effect of convection on the concentration field in the melt in front of the growing eutectic. While the theory agrees with the experimental spin-up spin-down results, it predicts that the weak convection expected due to buoyancy will not produce a measurable change in eutectic microstructure. Thus, this theory does not explain the two fold decrease in MnBi fiber size and spacing observed when MnBi-Bi is solidified in space or on Earth with a magnetic field applied. Attention was turned to the morphology of the MnBi-Bi interface and to the generation of freezing rate fluctuations by convection. Decanting the melt during solidification of MnBi-Bi eutectic showed that the MnBi phase projects into the melt ahead of the Bi matrix. Temperature measurements in a Bi melt in the vertical Bridgman-Stockbarger configuration showed temperature variations of up to 25 C. Conclusions are drawn and discussed.

Ozone disintegration of excess biomass and application to nitrogen removal.

PubMed

Park, Ki Young; Lee, Jae Woo; Ahn, Kyu-Hong; Maeng, Sung Kyu; Hwang, Jong Hyuk; Song, Kyung-Guen

2004-01-01

A pilot-scale facility integrated with an ozonation unit was built to investigate the feasibility of using ozone-disintegration byproducts of wasted biomass as a carbon source for denitrification. Ozonation of biomass resulted in mass reduction by mineralization as well as by ozone-disintegrated biosolids recycling. Approximately 50% of wasted solids were recovered as available organic matter (ozonolysate), which included nonsettleable microparticles and soluble fractions. Microparticles were observed in abundance at relatively low levels of ozone doses, while soluble fractions became dominant at higher levels of ozone doses in ozone-disintegrated organics. Batch denitrification experiments showed that the ozonolysate could be used as a carbon source with a maximum denitrification rate of 3.66 mg nitrogen (N)/g volatile suspended solids (VSS) x h. Ozonolysate was also proven to enhance total nitrogen removal efficiency in the pilot-scale treatment facility. An optimal chemical oxygen demand (COD)-to-nitrogen ratio for complete denitrification was estimated as 5.13 g COD/g N. The nitrogen-removal performance of the modified intermittently decanted extended aeration process dependent on an external carbon supply could be described as a function of solids retention time.

Plant observation report and evaluation, Pennwalt Corporation, secondary and tertiary aliphatic monoamines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-08-27

A site visit was made to the amine manufacturing facility of the Pennwalt Corporation, Wyandotte, Michigan, to evaluate the facility in regard to the Secondary and Tertiary Aliphatic Monoamines Criteria Document. A total of 21 people were directly in contact with the amine production process. Two to four of the maintenance personnel may also come in contact with the process. Maintenance workers ran the risk of exposure not only to primary, secondary and tertiary amine compounds, but also to several other chemicals being used in the process. The processes used to unload raw materials are described, along with reactor operations,more » decanter and recycling operations, distillation operations, product storage and shipping. Medical monitoring at the facility included chest x-ray, respiratory function tests, sight screening, urinalysis, and back x-rays. Restricted and potentially hazardous area signs were clearly posted. Employees wore hard hats and safety glasses on the job as well as gloves, rubber boots, face shields, goggles, and respirators as necessary. Emergency procedures are described, including fire protection. Sanitation and personal hygiene are discussed, along with monitoring of the workplace conditions.« less

Cellular Response to Doping of High Porosity Foamed Alumina with Ca, P, Mg, and Si.

PubMed

Soh, Edwin; Kolos, Elizabeth; Ruys, Andrew J

2015-03-13

Foamed alumina was previously synthesised by direct foaming of sulphate salt blends varying ammonium mole fraction (AMF), foaming heating rate and sintering temperature. The optimal product was produced with 0.33AMF, foaming at 100 °C/h and sintering at 1600 °C. This product attained high porosity of 94.39%, large average pore size of 300 µm and the highest compressive strength of 384 kPa. To improve bioactivity, doping of porous alumina by soaking in dilute or saturated solutions of Ca, P, Mg, CaP or CaP + Mg was done. Saturated solutions of Ca, P, Mg, CaP and CaP + Mg were made with excess salt in distilled water and decanted. Dilute solutions were made by diluting the 100% solution to 10% concentration. Doping with Si was done using the sol gel method at 100% concentration only. Cell culture was carried out with MG63 osteosarcoma cells. Cellular response to the Si and P doped samples was positive with high cell populations and cell layer formation. The impact of doping with phosphate produced a result not previously reported. The cellular response showed that both Si and P doping improved the biocompatibility of the foamed alumina.

Buttock augmentation: case studies of fat injection monitored by magnetic resonance imaging.

PubMed

Murillo, William L

2004-11-01

This article examines the injection of megavolumes of autologous fat cells as a means of buttock augmentation in 162 patients over a 7-year period. The author documents the use of magnetic resonance imaging in six patients to visualize the intramuscular location, integration, and duration of the injected fat. With the patient under epidural or general anesthesia, fat cells were harvested with a 5-mm blunt cannula and then stored in an empty sterile intravenous bag or bottle trap. Decantation was the only process used to separate the fat cells from the saline and serosanguineous components. Up to 1260 cc of fat cells were been injected into each buttock, the largest amount of fat grafting ever reported. Clinical assessment estimated a 20 percent loss of augmentation effect during the first 4 months. Patients were generally pleased with the final shape and volume of the buttock contour. In follow-up evaluation, magnetic resonance imaging supported the clinical indicators that the injection of large quantities of fat cells appears to be a safe and effective method for buttock enhancement. This process has inherent advantages; nevertheless, further research is required to clarify our understanding of the predictability and longevity of this technique.

Lab on a CD.

PubMed

Madou, Marc; Zoval, Jim; Jia, Guangyao; Kido, Horacio; Kim, Jitae; Kim, Nahui

2006-01-01

In this paper, centrifuge-based microfluidic platforms are reviewed and compared with other popular microfluidic propulsion methods. The underlying physical principles of centrifugal pumping in microfluidic systems are presented and the various centrifuge fluidic functions, such as valving, decanting, calibration, mixing, metering, heating, sample splitting, and separation, are introduced. Those fluidic functions have been combined with analytical measurement techniques, such as optical imaging, absorbance, and fluorescence spectroscopy and mass spectrometry, to make the centrifugal platform a powerful solution for medical and clinical diagnostics and high throughput screening (HTS) in drug discovery. Applications of a compact disc (CD)-based centrifuge platform analyzed in this review include two-point calibration of an optode-based ion sensor, an automated immunoassay platform, multiple parallel screening assays, and cellular-based assays. The use of modified commercial CD drives for high-resolution optical imaging is discussed as well. From a broader perspective, we compare technical barriers involved in applying microfluidics for sensing and diagnostic use and applying such techniques to HTS. The latter poses less challenges and explains why HTS products based on a CD fluidic platform are already commercially available, whereas we might have to wait longer to see commercial CD-based diagnostics.

The impact of fruit maturation on bioactive microconstituents, inhibition of serum oxidation and inflammatory markers in stimulated PBMCs and sensory characteristics of Koroneiki virgin olive oils from Messenia, Greece.

PubMed

Kaliora, Andriana C; Artemiou, Anna; Giogios, Ioannis; Kalogeropoulos, Nick

2013-08-01

Olive fruits from the Koroneiki cultivar (Olea europaea L.) grown in Messenia, Greece, were hand-picked from the same trees in progressive maturity stages, covering three months, and processed identically with a commercial olive mill and a three-phase decanter. Data on quality parameters, and antioxidant activity of the obtained oils were collected by employing the conventional analytical methods set by European Union Commission Regulation no. 61/2011. Additionally, the potential of oils' polar extract to inhibit total serum lipid oxidation and inflammatory markers in stimulated human mononuclear cells was assayed. The results showed that ripening caused an increase in monounsaturated and decrease in polyunsaturated fatty acids, as well as an increase in phenolic compounds - mainly hydroxytyrosol - and in squalene. The extracts' ferric reducing power was in line with the increase of phenolic compounds. In later stages of maturation, lipoprotein oxidation was less potent and the decrease of inflammatory markers in stimulated human mononuclear cells was more powerful. Sensory evaluation detected differences in oils' "bitter" attributes, while the analysis of oils' volatiles revealed quantitative differences.

Late Quaternary megafloods from Glacial Lake Atna, Southcentral Alaska, U.S.A.

NASA Astrophysics Data System (ADS)

Wiedmer, Michael; Montgomery, David R.; Gillespie, Alan R.; Greenberg, Harvey

2010-05-01

Geomorphic, stratigraphic, geotechnical, and biogeographic evidence indicate that failure of a Pleistocene ice dam between 15.5 and 26 ka generated a megaflood from Glacial Lake Atna down the Matanuska Valley. While it has long been recognized that Lake Atna occupied ≥ 9000 km 2 of south-central Alaska's Copper River Basin, little attention has focused on the lake's discharge locations and behaviors. Digital elevation model and geomorphic analyses suggest that progressive lowering of the lake level by decanting over spillways exposed during glacial retreat led to sequential discharges down the Matanuska, Susitna, Tok, and Copper river valleys. Lake Atna's size, ˜ 50 ka duration, and sequential connection to four major drainages likely made it a regionally important late Pleistocene freshwater refugium. We estimate a catastrophic Matanuska megaflood would have released 500-1400 km 3 at a maximum rate of ≥ 3 × 10 6 m 3 s - 1 . Volumes for the other outlets ranged from 200 to 2600 km 3 and estimated maximum discharges ranged from 0.8 to 11.3 × 10 6 m 3 s - 1 , making Lake Atna a serial generator of some of the largest known freshwater megafloods.

Effects of chilled storage and cryopreservation on sperm characteristics, antioxidant enzyme activities, and lipid peroxidation in Pacific cod Gadus microcephalus

NASA Astrophysics Data System (ADS)

Wang, Xueying; Shi, Xuehui; Liu, Yifan; Yu, Daode; Guan, Shuguang; Liu, Qinghua; Li, Jun

2016-07-01

The present study evaluated the effects of chilled storage and cryopreservation on sperm motion characteristics, antioxidant enzyme activities, and lipid peroxidation in the Pacific cod Gadus macrocephalus. Sperm motility and the activities of superoxide dismutase (SOD), catalase (CAT), glutathione peroxidase (GPx), glutathione reductase (Gr), and lipid peroxidation (measured via malondialdehyde (MDA) content) were determined after the milt was stored at 4°C for 12 h, cryopreserved without cryoprotectant in 12% propylene glycol (PG), cryopreserved in 12% PG+0.1 mol/L trehalose, or cryopreserved in 12% PG spermatozoa but centrifuged to decant the supernatant prior to cryopreservation (only sperm cells were cryopreserved). After chilled storage or cryopreservation, the SOD, CAT and GPx activities were reduced in sperm cells and increased in seminal plasma in almost all treatments; sperm motility parameters were also decreased. However, the addition of trehalose into the cryoprotectant could significantly improve the postthaw sperm quality as revealed by the sperm average path velocity. This improvement might be attributed to the function of trehalose in scavenging reactive oxygen species. Chilled storage and cryopreservation had significant effects on sperm motion characteristics, antioxidant enzyme activities, and lipid peroxidation in the Pacific cod.

Extraction of Oleic Acid from Moroccan Olive Mill Wastewater

PubMed Central

Elkacmi, Reda; Kamil, Noureddine; Bennajah, Mounir; Kitane, Said

2016-01-01

The production of olive oil in Morocco has recently grown considerably for its economic and nutritional importance favored by the country's climate. After the extraction of olive oil by pressing or centrifuging, the obtained liquid contains oil and vegetation water which is subsequently separated by decanting or centrifugation. Despite its treatment throughout the extraction process, this olive mill wastewater, OMW, still contains a very important oily residue, always regarded as a rejection. The separated oil from OMW can not be intended for food because of its high acidity of 3.397% which exceeds the international standard for human consumption defined by the standard of the Codex Alimentarius, proving its poor quality. This work gives value addition to what would normally be regarded as waste by the extraction of oleic acid as a high value product, using the technique of inclusion with urea for the elimination of saturated and unsaturated fatty acids through four successive crystallizations at 4°C and 20°C to have a final phase with oleic acid purity of 95.49%, as a biodegradable soap and a high quality glycerin will be produced by the reaction of saponification and transesterification. PMID:26933663

Mechanisms of post-supply contamination of drinking water in Bagamoyo, Tanzania.

PubMed

Harris, Angela R; Davis, Jennifer; Boehm, Alexandria B

2013-09-01

Access to household water connections remains low in sub-Saharan Africa, representing a public health concern. Previous studies have shown water stored in the home to be more contaminated than water at the source; however, the mechanisms of post-supply contamination remain unclear. Using water quality measurements and structured observations of households in Bagamoyo, Tanzania, this study elucidates the causal mechanisms of the microbial contamination of drinking water after collection from a communal water source. The study identifies statistically significant loadings of fecal indicator bacteria (FIB) occurring immediately after filling the storage container at the source and after extraction of the water from the container in the home. Statistically significant loadings of FIB also occur with various water extraction methods, including decanting from the container and use of a cup or ladle. Additionally, pathogenic genes of Escherichia coli were detected in stored drinking water but not in the source from which it was collected, highlighting the potential health risks of post-supply contamination. The results of the study confirm that storage containers and extraction utensils introduce microbial contamination into stored drinking water, and suggest that further research is needed to identify methods of water extraction that prevent microbial contamination of drinking water.

State of the art of produced water treatment.

PubMed

Jiménez, S; Micó, M M; Arnaldos, M; Medina, F; Contreras, S

2018-02-01

Produced water (PW) is the wastewater generated when water from underground reservoirs is brought to the surface during oil or gas extraction. PW is generated in large amounts and has a complex composition, containing various toxic organic and inorganic compounds. PW is currently treated in conventional trains that include phase separators, decanters, cyclones and coarse filters in order to comply with existing regulation for discharge. These treatment trains do not achieve more restrictive limitations related to the reuse of the effluent (reinjection into extraction wells) or other beneficial uses (e.g., irrigation). Therefore, and to prevent environmental pollution, further polishing processes need to be carried out. Characterization of the PW to determine major constituents is the first step to select the optimum treatment for PW, coupled with environmental factors, economic considerations, and local regulatory framework. This review tries to provide an overview of different treatments that are being applied to polish this type of effluents. These technologies include membranes, physical, biological, thermal or chemical treatments, where special emphasis has been made on advanced oxidation processes due to the advantages offered by these processes. Commercial treatments, based on the combination, modification and improvement of simpler treatments, were also discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enrichment of rare earth elements as environmental tracers of contamination by acid mine drainage in salt marshes: a new perspective.

PubMed

Delgado, Joaquín; Pérez-López, Rafael; Galván, Laura; Nieto, José Miguel; Boski, Tomasz

2012-09-01

Rare earth elements (REE) were analyzed in surface sediments from the Guadiana Estuary (SW Iberian Pyrite Belt). NASC (North American Shale Composite) normalized REE patterns show clearly convex curvatures in middle-REE (MREE) with respect to light- and heavy-REE, indicating acid-mixing processes between fluvial waters affected by acid mine drainage (AMD) and seawater. However, REE distributions in the mouth (closer to the coastal area) show slightly LREE-enriched and flat patterns, indicating saline-mixing processes typical of the coastal zone. NASC-normalized ratios (La/Gd and La/Yb) do not discriminate between both mixing processes in the estuary. Instead, a new parameter (E(MREE)) has been applied to measure the curvature in the MREE segment. The values of E(MREE)>0 are indicative of acid signatures and their spatial distribution reveal the existence of two decantation zones from flocculation processes related to drought periods and flood events. Studying REE fractionation through the E(MREE) may serve as a good proxy for AMD-pollution in estuarine environments in relation to the traditional methods. Copyright © 2012 Elsevier Ltd. All rights reserved.

SIMPL: A Simplified Model-Based Program for the Analysis and Visualization of Groundwater Rebound in Abandoned Mines to Prevent Contamination of Water and Soils by Acid Mine Drainage

PubMed Central

Kim, Sung-Min

2018-01-01

Cessation of dewatering following underground mine closure typically results in groundwater rebound, because mine voids and surrounding strata undergo flooding up to the levels of the decant points, such as shafts and drifts. SIMPL (Simplified groundwater program In Mine workings using the Pipe equation and Lumped parameter model), a simplified lumped parameter model-based program for predicting groundwater levels in abandoned mines, is presented herein. The program comprises a simulation engine module, 3D visualization module, and graphical user interface, which aids data processing, analysis, and visualization of results. The 3D viewer facilitates effective visualization of the predicted groundwater level rebound phenomenon together with a topographic map, mine drift, goaf, and geological properties from borehole data. SIMPL is applied to data from the Dongwon coal mine and Dalsung copper mine in Korea, with strong similarities in simulated and observed results. By considering mine workings and interpond connections, SIMPL can thus be used to effectively analyze and visualize groundwater rebound. In addition, the predictions by SIMPL can be utilized to prevent the surrounding environment (water and soil) from being polluted by acid mine drainage. PMID:29747480

Extraction of Oleic Acid from Moroccan Olive Mill Wastewater.

PubMed

Elkacmi, Reda; Kamil, Noureddine; Bennajah, Mounir; Kitane, Said

2016-01-01

The production of olive oil in Morocco has recently grown considerably for its economic and nutritional importance favored by the country's climate. After the extraction of olive oil by pressing or centrifuging, the obtained liquid contains oil and vegetation water which is subsequently separated by decanting or centrifugation. Despite its treatment throughout the extraction process, this olive mill wastewater, OMW, still contains a very important oily residue, always regarded as a rejection. The separated oil from OMW can not be intended for food because of its high acidity of 3.397% which exceeds the international standard for human consumption defined by the standard of the Codex Alimentarius, proving its poor quality. This work gives value addition to what would normally be regarded as waste by the extraction of oleic acid as a high value product, using the technique of inclusion with urea for the elimination of saturated and unsaturated fatty acids through four successive crystallizations at 4°C and 20°C to have a final phase with oleic acid purity of 95.49%, as a biodegradable soap and a high quality glycerin will be produced by the reaction of saponification and transesterification.

Analysis of Possibility of Yeast Production Increase at Maintained Carbon Dioxide Emission Level

NASA Astrophysics Data System (ADS)

Włodarczyk, Barbara; Włodarczyk, Paweł P.

2016-12-01

Main parameters polluting of technological wastewater (dregs from decantation and thicken of the wort) from yeast industry are: nitrogen, potassium and COD. Such wastewater are utilized mostly on agricultural fields. Unfortunately, these fields can only accept a limited amount of wastes. The basic parameter limiting there the amount of wastewater is nitrogen. When capacity of the production is large sewages are often pretreated at an evaporator station. However, due to the fairly high running costs of the evaporator station currently such a solution is applied only to a small amount of wastes (just to meet legal requirements). Replacement of the earth gas with a biomass being supplied to the evaporator station from the agricultural fields will both allow to maintain the carbon dioxide emission level and enable the production growth. Moreover, the biomass growing on the agricultural fields being fertilized with the wastewater coming from the yeast production allows consequently to utilize the greater volume of wastewater. Theoretically, the possible increase in the yeasts production, with maintaining the carbon dioxide emission level, can reach even 70%. Therefore, the solution presented in this paper combines both intensification of the yeasts production and maintaining the carbon dioxide emission level.

Characterisation and optimisation of flexible transfer lines for liquid helium. Part II: Thermohydraulic modelling

NASA Astrophysics Data System (ADS)

Dittmar, N.; Haberstroh, Ch.; Hesse, U.; Krzyzowski, M.

2016-10-01

In part one of this publication experimental results for a single-channel transfer line used at liquid helium (LHe) decant stations are presented. The transfer of LHe into mobile dewars is an unavoidable process since the places of storage and usage are generally located apart from each other. The experimental results have shown that reasonable amounts of LHe evaporate due to heat leak and pressure drop. Thus, generated helium cold gas has to be collected and reliquefied, demanding a huge amount of electrical energy. Although this transfer process is common in cryogenic laboratories, no existing code could be found to model it. Therefore, a thermohydraulic model has been developed to model the LHe flow at operating conditions using published heat transfer and pressure drop correlations. This paper covers the basic equations used to calculate heat transfer and pressure drop, as well as the validation of the thermohydraulic code, and its application within the optimisation process. The final transfer line design features reduced heat leak and pressure drop values based on a combined measurement and modelling campaign in the range of 0.112 < pin < 0.148 MPa, 190 < G < 450 kg/(m2 s), and 0.04 < xout < 0.12.

Faecal indicator bacteria enumeration in beach sand: a comparison study of extraction methods in medium to coarse sands.

PubMed

Boehm, A B; Griffith, J; McGee, C; Edge, T A; Solo-Gabriele, H M; Whitman, R; Cao, Y; Getrich, M; Jay, J A; Ferguson, D; Goodwin, K D; Lee, C M; Madison, M; Weisberg, S B

2009-11-01

The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Method standardization will improve the understanding of how sands affect surface water quality.

Biogas and biohydrogen production potential of high strength automobile industry wastewater during anaerobic degradation.

PubMed

Bajaj, Mini; Winter, Josef

2013-10-15

High strength automobile industry wastewater, collected from decanters (DECA) of the pre-treatment plant after oil, grease and sludge separation, was investigated for production of methane in the absence and presence of glucose or excess aerobic sludge (AS) from a lab scale suspension reactor as co-substrates. The highest methane production from DECA wastewater was 335.4 L CH4/kg CODsoluble removal which decreased in the presence of the co-substrates to 232.5 (with 2 g/L glucose) and to 179 (with 40% AS) L CH4/kg CODsoluble removal, respectively. Around 95% of total methane was produced within 5 days of incubation of DECA at 37 °C when no co-substrate was added. Addition of co-substrates did not improve biodegradation of DECA but overall methane production from DECA + co-substrates was increased due to co-substrate biodegradation. The anaerobic inoculum, capable of producing 2.4 mol of hydrogen/mol of glucose under zinc induced inhibitory conditions, was unable to produce hydrogen from DECA as substrate under the same conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Implications of exposure to dextran-coated and uncoated iron oxide nanoparticles to developmental toxicity in zebrafish

NASA Astrophysics Data System (ADS)

de Oliveira, Giovanna Medeiros Tavares; de Oliveira, Elisa Magno Nunes; Pereira, Talita Carneiro Brandão; Papaléo, Ricardo Meurer; Bogo, Maurício Reis

2017-12-01

Iron oxide nanoparticles (IONPS) have been widely investigated as a platform for a new class of multifunctional theranostic agents. They are considered biocompatible, and some formulations are already available in the market for clinical use. However, contradictory results regarding toxicity of IONPs raise a concern about the potential harm of these nanoparticles. Changes in the nanoparticle (NP) physicochemical properties or exposure media can significantly alter their behavior and, as a consequence, their toxic effects. Here, behavior and two-step RT-qPCR were employed to access the potential toxicological effects of dextran-coated IONPs (CLIO-NH2) and uncoated IONPs (UCIO) in zebrafish larvae. Animals were exposed for 7 days to NP solutions ranging from 0.1-100 μg/mL directly mixed to the system water. UCIO showed high decantation and instability in solution, altering zebrafish mortality but showing no alterations in behavior and molecular expression analysis. CLIO-NH2 exposure did not cause significant mortality or changes in hatching rate of zebrafish larvae; however, behavior and expression profiles of the group exposed to lower concentration (1 μg/mL) presented a tendency to decrease the locomotor activity and apoptotic pathway activation.

Effects of vegetation on chemical and mineralogical characteristics of soils developed on a decantation bank from a copper mine.

PubMed

Cerqueira, Beatriz; Vega, Flora A; Silva, Luis F O; Andrade, Luisa

2012-04-01

Open cast mining has a strong impact on the environment, the intensity depending on the morphology of the deposit and on the nature of the minerals. At Touro mine (NW Spain) there is a large area covered by tailings, one of which, called the "sedimentation bank", was used to deposit sludge resulting from the extraction of copper in the flotation plant. Three zones were selected and the soils were sampled to analyse the changes brought about by vegetation on the chemical and mineralogical properties of the soils developed over the sedimentation bank and its development over time. The vegetation increased the pH, contents of organic material, nitrogen, clay and free oxides of Fe and Al, and the cationic exchange capacity of the soils. The decrease in the sulphide content, benefited by the vegetation process, led to a reduction in the total content of Cr and Cu. The vegetation also contributed towards the alteration of the primary minerals. The transformation of jarosite, the formation of nanocrystals of hematite, goethite, hydroxypolymers, and amorphous minerals that contained Cu, Cr and Pb were observed. Nevertheless the high Cu and Cr contents indicate that it is advisable to change the restoration process. Copyright © 2012 Elsevier B.V. All rights reserved.

Faecal indicator bacteria enumeration in beach sand: A comparison study of extraction methods in medium to coarse sands

USGS Publications Warehouse

Boehm, A.B.; Griffith, J.; McGee, C.; Edge, T.A.; Solo-Gabriele, H. M.; Whitman, R.; Cao, Y.; Getrich, M.; Jay, J.A.; Ferguson, D.; Goodwin, K.D.; Lee, C.M.; Madison, M.; Weisberg, S.B.

2009-01-01

Aims: The absence of standardized methods for quantifying faecal indicator bacteria (FIB) in sand hinders comparison of results across studies. The purpose of the study was to compare methods for extraction of faecal bacteria from sands and recommend a standardized extraction technique. Methods and Results: Twenty-two methods of extracting enterococci and Escherichia coli from sand were evaluated, including multiple permutations of hand shaking, mechanical shaking, blending, sonication, number of rinses, settling time, eluant-to-sand ratio, eluant composition, prefiltration and type of decantation. Tests were performed on sands from California, Florida and Lake Michigan. Most extraction parameters did not significantly affect bacterial enumeration. anova revealed significant effects of eluant composition and blending; with both sodium metaphosphate buffer and blending producing reduced counts. Conclusions: The simplest extraction method that produced the highest FIB recoveries consisted of 2 min of hand shaking in phosphate-buffered saline or deionized water, a 30-s settling time, one-rinse step and a 10 : 1 eluant volume to sand weight ratio. This result was consistent across the sand compositions tested in this study but could vary for other sand types. Significance and Impact of the Study: Method standardization will improve the understanding of how sands affect surface water quality. ?? 2009 The Society for Applied Microbiology.

Multi-step process for concentrating magnetic particles in waste sludges

DOEpatents

Watson, John L.

1990-01-01

This invention involves a multi-step, multi-force process for dewatering sludges which have high concentrations of magnetic particles, such as waste sludges generated during steelmaking. This series of processing steps involves (1) mixing a chemical flocculating agent with the sludge; (2) allowing the particles to aggregate under non-turbulent conditions; (3) subjecting the mixture to a magnetic field which will pull the magnetic aggregates in a selected direction, causing them to form a compacted sludge; (4) preferably, decanting the clarified liquid from the compacted sludge; and (5) using filtration to convert the compacted sludge into a cake having a very high solids content. Steps 2 and 3 should be performed simultaneously. This reduces the treatment time and increases the extent of flocculation and the effectiveness of the process. As partially formed aggregates with active flocculating groups are pulled through the mixture by the magnetic field, they will contact other particles and form larger aggregates. This process can increase the solids concentration of steelmaking sludges in an efficient and economic manner, thereby accomplishing either of two goals: (a) it can convert hazardous wastes into economic resources for recycling as furnace feed material, or (b) it can dramatically reduce the volume of waste material which must be disposed.

Multi-step process for concentrating magnetic particles in waste sludges

DOEpatents

Watson, J.L.

1990-07-10

This invention involves a multi-step, multi-force process for dewatering sludges which have high concentrations of magnetic particles, such as waste sludges generated during steelmaking. This series of processing steps involves (1) mixing a chemical flocculating agent with the sludge; (2) allowing the particles to aggregate under non-turbulent conditions; (3) subjecting the mixture to a magnetic field which will pull the magnetic aggregates in a selected direction, causing them to form a compacted sludge; (4) preferably, decanting the clarified liquid from the compacted sludge; and (5) using filtration to convert the compacted sludge into a cake having a very high solids content. Steps 2 and 3 should be performed simultaneously. This reduces the treatment time and increases the extent of flocculation and the effectiveness of the process. As partially formed aggregates with active flocculating groups are pulled through the mixture by the magnetic field, they will contact other particles and form larger aggregates. This process can increase the solids concentration of steelmaking sludges in an efficient and economic manner, thereby accomplishing either of two goals: (a) it can convert hazardous wastes into economic resources for recycling as furnace feed material, or (b) it can dramatically reduce the volume of waste material which must be disposed. 7 figs.

Influence of prefermentary clarification on the composition of apple musts.

PubMed

Hubert, Bertrand; Baron, Alain; Le Quere, Jean-Michel; Renard, Catherine M G C

2007-06-27

The polyphenol contents and colors of cider apple juices were compared before (NCM, not clarified must) and after five clarification treatments: enzymatic depectinization by pectinases followed by (i) sedimentation (depectinized and decanted juice), (ii) tangential microfiltration (microfiltered juice) or (iii) fining using gelatin (gelatin-treated juice); (iv) enzymatic gelification of pectin by pectin methylesterase followed by natural keeving by a cider manufacturer (producer keeved juice), or (v) flotation (floated with nitrogen gas juice). The pressing of the apples led to the highly selective extraction of the flavan-3-ols with the lowest molecular weights: In the apples, the number average degree of polymerization of the flavanols was 14.7, and it dropped to 2.2 in the NCM. Keeving had the highest impact on the reduction of both flavanol content and number average degree of polymerization. The flavanol concentrations were decreased in the permeate by fining (30%) much more than by depectinization. The clarification step led to a further decrease of the number average degree of polymerization. Hydroxycinnamic acids were less affected by the extraction process (with extraction yields >50%) and not affected by clarification. The color evolved with all treatments: L*, a*, b*, and chromaticity distance index measures indicated a reduction of orange-yellow saturation except after sedimentation.

Removal of Total Coliforms, Thermotolerant Coliforms, and Helminth Eggs in Swine Production Wastewater Treated in Anaerobic and Aerobic Reactors

PubMed Central

Zacarias Sylvestre, Silvia Helena; Lux Hoppe, Estevam Guilherme; de Oliveira, Roberto Alves

2014-01-01

The present work evaluated the performance of two treatment systems in reducing indicators of biological contamination in swine production wastewater. System I consisted of two upflow anaerobic sludge blanket (UASB) reactors, with 510 and 209 L in volume, being serially arranged. System II consisted of a UASB reactor, anaerobic filter, trickling filter, and decanter, being also organized in series, with volumes of 300, 190, 250, and 150 L, respectively. Hydraulic retention times (HRT) applied in the first UASB reactors were 40, 30, 20, and 11 h in systems I and II. The average removal efficiencies of total and thermotolerant coliforms in system I were 92.92% to 99.50% and 94.29% to 99.56%, respectively, and increased in system II to 99.45% to 99.91% and 99.52% to 99.93%, respectively. Average removal rates of helminth eggs in system I were 96.44% to 99.11%, reaching 100% as in system II. In reactor sludge, the counts of total and thermotolerant coliforms ranged between 105 and 109 MPN (100 mL)−1, while helminth eggs ranged from 0.86 to 9.27 eggs g−1 TS. PMID:24812560

Comparing centralised and decentralised anaerobic digestion of stillage from a large-scale bioethanol plant to animal feed production.

PubMed

Drosg, B; Wirthensohn, T; Konrad, G; Hornbachner, D; Resch, C; Wäger, F; Loderer, C; Waltenberger, R; Kirchmayr, R; Braun, R

2008-01-01

A comparison of stillage treatment options for large-scale bioethanol plants was based on the data of an existing plant producing approximately 200,000 t/yr of bioethanol and 1,400,000 t/yr of stillage. Animal feed production--the state-of-the-art technology at the plant--was compared to anaerobic digestion. The latter was simulated in two different scenarios: digestion in small-scale biogas plants in the surrounding area versus digestion in a large-scale biogas plant at the bioethanol production site. Emphasis was placed on a holistic simulation balancing chemical parameters and calculating logistic algorithms to compare the efficiency of the stillage treatment solutions. For central anaerobic digestion different digestate handling solutions were considered because of the large amount of digestate. For land application a minimum of 36,000 ha of available agricultural area would be needed and 600,000 m(3) of storage volume. Secondly membrane purification of the digestate was investigated consisting of decanter, microfiltration, and reverse osmosis. As a third option aerobic wastewater treatment of the digestate was discussed. The final outcome was an economic evaluation of the three mentioned stillage treatment options, as a guide to stillage management for operators of large-scale bioethanol plants. Copyright IWA Publishing 2008.

Engineered ecosystem for on-site wastewater treatment in tropical areas.

PubMed

de Sá Salomão, André Luis; Marques, Marcia; Severo, Raul Gonçalves; da Cruz Roque, Odir Clécio

2012-01-01

There is a worldwide demand for decentralized wastewater treatment options. An on-site engineered ecosystem (EE) treatment plant was designed with a multistage approach for small wastewater generators in tropical areas. The array of treatment units included a septic tank, a submersed aerated filter, and a secondary decanter followed by three vegetated tanks containing aquatic macrophytes intercalated with one tank of algae. During 11 months of operation with a flow rate of 52 L h(-1), the system removed on average 93.2% and 92.9% of the chemical oxygen demand (COD) and volatile suspended solids (VSS) reaching final concentrations of 36.3 ± 12.7 and 13.7 ± 4.2 mg L(-1), respectively. Regarding ammonia-N (NH(4)-N) and total phosphorus (TP), the system removed on average 69.8% and 54.5% with final concentrations of 18.8 ± 9.3 and 14.0 ± 2.5 mg L(-1), respectively. The tanks with algae and macrophytes together contributed to the overall nutrient removal with 33.6% for NH(4)-N and 26.4% for TP. The final concentrations for all parameters except TP met the discharge threshold limits established by Brazilian and EU legislation. The EE was considered appropriate for the purpose for which it was created.

Modeling of a complex, polar system with a modified Soave-Redlich-Kwong equation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sturnfield, E.A.; Matherne, J.L.

1988-01-01

It is computationally feasible to use a simple equation of state (like a Redlich-Kwong) to calculate liquid fugacity but the simpler equations work well only for moderately non-ideal systems. More complex equations (like Ghemling-Lui-Prausnitz) predict system behavior more accurately but are much more complicated to use and can require fitting many parameters to data. This paper illustrates success in using a modified Redlich-Kwong to model a complex system including water, hydrogen, sub and supercritical ammonia, and amines. The binary interaction parameter ({Kappa}/sub ij/) of the Soave-Redlich-Kwong equation has been modified to be both asymmetric and temperature dependent. Further, the aimore » constant was determined by fitting vapor pressure data. Predicted model results are compared to literature (example 1) or plant data (examples 2-4) for four systems: 1. The ammonia-water binary over a wide range of pressure and temperature including ammonia above its critical. 2. A multicomponent Vapor-Liquid equilibrium flash tank and condenser containg hydrogen, amonia, water, and other heavier compounds. 3. A multicomponent vapor-liquid equilibrium flash tank containing water, heavier mines, and the amine salts. 4. A Liquid-Liquid-Vapor equilibrium decanter system containing water, ammonia, and an organic chloride.« less

Determination of rhodium in metallic alloy and water samples using cloud point extraction coupled with spectrophotometric technique

NASA Astrophysics Data System (ADS)

Kassem, Mohammed A.; Amin, Alaa S.

2015-02-01

A new method to estimate rhodium in different samples at trace levels had been developed. Rhodium was complexed with 5-(4‧-nitro-2‧,6‧-dichlorophenylazo)-6-hydroxypyrimidine-2,4-dione (NDPHPD) as a complexing agent in an aqueous medium and concentrated by using Triton X-114 as a surfactant. The investigated rhodium complex was preconcentrated with cloud point extraction process using the nonionic surfactant Triton X-114 to extract rhodium complex from aqueous solutions at pH 4.75. After the phase separation at 50 °C, the surfactant-rich phase was heated again at 100 °C to remove water after decantation and the remaining phase was dissolved using 0.5 mL of acetonitrile. Under optimum conditions, the calibration curve was linear for the concentration range of 0.5-75 ng mL-1 and the detection limit was 0.15 ng mL-1 of the original solution. The enhancement factor of 500 was achieved for 250 mL samples containing the analyte and relative standard deviations were ⩽1.50%. The method was found to be highly selective, fairly sensitive, simple, rapid and economical and safely applied for rhodium determination in different complex materials such as synthetic mixture of alloys and environmental water samples.

Enumeration and rapid identification of yeasts during extraction processes of extra virgin olive oil in Tuscany.

PubMed

Mari, Eleonora; Guerrini, Simona; Granchi, Lisa; Vincenzini, Massimo

2016-06-01

The aim of this study was to evaluate the occurrence of yeast populations during different olive oil extraction processes, carried out in three consecutive years in Tuscany (Italy), by analysing crushed pastes, kneaded pastes, oil from decanter and pomaces. The results showed yeast concentrations ranging between 10(3) and 10(5) CFU/g or per mL. Seventeen dominant yeast species were identified by random amplified polymorphic DNA with primer M13 and their identification was confirmed by restriction fragments length polymorphism of ribosomal internal transcribed spacer and sequencing rRNA genes. The isolation frequencies of each species in the collected samples pointed out that the occurrence of the various yeast species in olive oil extraction process was dependent not only on the yeasts contaminating the olives but also on the yeasts colonizing the plant for oil extraction. In fact, eleven dominant yeast species were detected from the washed olives, but only three of them were also found in oil samples at significant isolation frequency. On the contrary, the most abundant species in oil samples, Yamadazyma terventina, did not occur in washed olive samples. These findings suggest a phenomenon of contamination of the plant for oil extraction that selects some yeast species that could affect the quality of olive oil.

Petroleum hydrocarbon contamination, plant identity and arbuscular mycorrhizal fungal (AMF) community determine assemblages of the AMF spore-associated microbes.

PubMed

Iffis, Bachir; St-Arnaud, Marc; Hijri, Mohamed

2016-09-01

The root-associated microbiome is a key determinant of pollutant degradation, soil nutrient availability and plant biomass productivity, but could not be examined in depth prior to recent advances in high-throughput sequencing. Arbuscular mycorrhizal fungi (AMF) form symbioses with the majority of vascular plants. They are known to enhance mineral uptake and promote plant growth and are postulated to influence the processes involved in phytoremediation. Amplicon sequencing approaches have previously shown that petroleum hydrocarbon pollutant (PHP) concentration strongly influences AMF community structure in in situ phytoremediation experiments. We examined how AMF communities and their spore-associated microbiomes were structured within the rhizosphere of three plant species growing spontaneously in three distinct waste decantation basins of a former petrochemical plant. Our results show that the AMF community was only affected by PHP concentrations, while the AMF-associated fungal and bacterial communities were significantly affected by both PHP concentrations and plant species identity. We also found that some AMF taxa were either positively or negatively correlated with some fungal and bacterial groups. Our results suggest that in addition to PHP concentrations and plant species identity, AMF community composition may also shape the community structure of bacteria and fungi associated with AMF spores. © 2016 Society for Applied Microbiology and John Wiley & Sons Ltd.

Retention of membrane charge attributes by cryopreserved-thawed sperm and zeta selection.

PubMed

Kam, Tricia L; Jacobson, John D; Patton, William C; Corselli, Johannah U; Chan, Philip J

2007-09-01

Mature sperm can be selected based on their negative zeta electrokinetic potential. The zeta selection of cryopreserved sperm is unknown. The objective was to study the effect of zeta processing on the morphology and kinematic parameters of cryopreserved-thawed sperm. Colloid-washed sperm (N = 9 cases) were cryopreserved for 24 h, thawed and diluted in serum-free medium in positive-charged tubes. After centrifugation, the tubes were decanted, serum-supplemented medium was added and the resuspended sperm were analyzed. Untreated sperm and fresh sperm served as the controls. There were improvements in strict normal morphology in fresh (11.8 +/- 0.3 versus control 8.8 +/- 0.3 %, mean +/- SEM) and thawed (8.7 +/- 0.2 versus control 5.4 +/- 0.2%) sperm after zeta processing. Percent sperm necrosis was reduced after zeta processing (66.0 +/- 0.6 versus unprocessed 74.6 +/- 0.3%). Progression decreased by 50% but not total motility after zeta processing of thawed sperm. The results suggested that the cryopreservation process did not impact the sperm membrane net zeta potential and higher percentages of sperm with normal strict morphology, acrosome integrity and reduced necrosis were recovered. The zeta method was simple and improved the selection of quality sperm after cryopreservation but more studies would be needed before routine clinical application.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carnahan, T.G.; Kazonich, G.; Raddatz, A.E.

The U.S. Bureau of Mines conducted a bench-scale study to delineate the important parameters in a three-step process to produce commercial-quality tungsten carbide (WC) directly from tungsten minerals. In the process, tungsten concentrates of wolframite or wolframite and scheelite are decomposed at 1,050{sup 0}C in a molten mixture of NcCl and Na{sub 2}SiO{sub 3} that forms two immiscible phases. Tungsten, as sodium tungstate, reports to the halide phase and is separated from the gangue constituents, which report to the silicate phase. After decanting to separate the two phases, natural gas is sparged into the molten halide phase a 1,070{sup 0}C.more » Submicrometer crystals of WC are initially produced. These crystals grow into thin triangular-shaped plates up to 100 {mu}m on a side or into popcorn-shaped conglomerates. Sparged WC was examined for its suitability for use in sintered carbide products. In physical evaluations, sparged WC ground to an average particle size of 1.52 {mu}m and compacted with 10 pct Co binder into standard 6-by 22-mm test bars had a density of 14.35 and a Rockwell A hardness of 89.6. This compared favorably with 14.39 and 89.7 respectively, for test bars made from a standard commercial 1.52-{mu}m WC powder. Test bars made from Bureau of Mines WC had no C'' porosity or eta phase.« less

First Reports, Morphological, and Molecular Characterization of Longidorus caespiticola and Longidorus poessneckensis (Nematoda: Longidoridae) from Ukraine

PubMed Central

Susulovska, Solomia; Castillo, Pablo; Archidona-Yuste, Antonio

2017-01-01

Seven needle nematode species of the genus Longidorus have been reported in Ukraine. Nematological surveys for needle nematodes were carried out in Ukraine between 2016 and 2017 and two nematode species of Longidorus (L. caespiticola and L. poessneckensis) were collected from natural and anthropogenically altered habitats on the territory of Opillia and Zakarpattia in Ukraine. Nematodes were extracted from 500 cm3 of soil by modified sieving and decanting method. Extracted specimens were processed to glycerol and mounted on permanent slides and subsequently identified morphologically and molecularly. Nematode DNA was extracted from single individuals and PCR assays were conducted as previously described for D2–D3 expansion segments of 28S rRNA. Sequence alignments for D2–D3 from L. caespiticola showed 97%–99% similarity to other sequences of L. caespiticola deposited in GenBank from Belgium, Bulgaria, Czech Republic, Russia, Slovenia, and Scotland. Similarly, D2–D3 sequence alignments from L. poessneckensis, showed 99% to other sequences of L. poessneckensis deposited in GenBank from Slovakia and Czech Republic. Morphology, morphometry, and molecular data obtained from these samples were consistent with L. caespiticola and L. poessneckensis identification. To our knowledge, these are the first reports of L. caespiticola and L. poessneckensis in Ukraine, extending the geographical distribution of these species. PMID:29353928

Crystal growth and annealing study of fragile, non-bulk superconductivity in YFe 2Ge 2

DOE PAGES

Kim, H.; Ran, S.; Mun, E. D.; ...

2015-02-05

In this study, we investigated the occurrence and nature of superconductivity in single crystals of YFe 2Ge 2 grown out of Sn flux by employing X-ray diffraction, electrical resistivity and specific heat measurements. We found that the residual resistivity ratio (RRR) of single crystals can be greatly improved, reaching as high as ~60, by decanting the crystals from the molten Sn at ~350°C and/or by annealing at temperatures between 550°C and 600°C. We found that the samples with RRR ≳ 34 showed resistive signatures of superconductivity with the onset of the superconducting transition T c ≈ 1.4K. RRR values varymore » between 35 and 65 with, on average, no systematic change in value T c, indicating that the systematic changes in RRR do not lead to comparable changes in T c. Specific heat measurements on samples that showed the clear resistive signatures of a superconducting transition did not show any signature of a superconducting phase transition, which suggests that the superconductivity observed in this compound is either some sort of filamentary, strain-stabilized superconductivity associated with small amounts of stressed YFe 2Ge 2 (perhaps at twin boundaries or dislocations) or is a second crystallographic phase that is present at level below detection capability of conventional powder X-ray techniques.« less

Upland and wetland vegetation establishment on coal slurry in northern Missouri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skeel, V.A.; Nawrot, J.R.

Since the Cooperative Wildlife Research Laboratory`s (CWRL) Mined Land Reclamation Program`s first establishment of a wetland on slurry in 1976, industry, state, and federal agency interest in reclamation alternatives for inactive slurry has increased. CWRL has been involved in pre-reclamation site characterization and monitoring for inactive slurry impoundments throughout Illinois, Indiana, Kansas, Kentucky, Missouri, and Washington. Geochemical site characterization of three slurry impoundments at the AECI Bee Veer Mine located near Macon, Missouri began in April 1990. A substrate sampling grid was established for all slurry impoundments with a centerline orientated parallel to the discharge to decant flow pattern. Surfacemore » (0--6 in.) and subsurface (30--36 in.) slurry samples were collected annually and analyzed for acid-base balance, immediate acidity macro- and micro-nutrients, potential phytotoxic metallic ions and salts, and texture. Water table elevations and water quality were monitored quarterly from shallow ({le}12 ft.) piezometers. General reclamation plans included annual (3 years) incremental limestone amendments (35--50 tons/acre) and direct vegetation establishment. Cool and warm season grasses dominate vegetation cover in upland habitats (slurry cell RDA1) while wetland habitats (palustrine emergent seasonally-permanently inundated) have been established in slurry cells (RDA2 and RDA3). Isolated hot spots continue to be amended with limestone and supplemental vegetation establishment is scheduled.« less

Variations in the Rate of Infestations of Dogs with Zoonotic Nematodes and the Contamination of Soil in Different Environments

PubMed Central

Demkowska-Kutrzepa, Marta; Borecka, Anna; Meisner, Michał; Tomczuk, Krzysztof; Roczeń-Karczmarz, Monika; Kłapeć, Teresa; Abbass, Zahrai; Cholewa, Alicja

2017-01-01

Companion animals are an important aspect in human life. However, they may also be considered a source of pathogens. An example of zoonotic parasitoses is toxocarosis or cutaneous larva migrans (CLM). The aim of the study was to detect zoonotic nematodes of dogs living in different areas and the intensity of contamination in parasite polluted environments that are hazardous to human health. The fecal samples were examined using standard flotation and decantation methods as well as McMaster’s quantitative technique. The soil samples in urban and rural areas were examined using a modified flotation method as described by Quinn et al. Statistical analyses were performed by IBM SPSS Statistics Version 23. The overall prevalence of parasites in dogs was 38%, 17.02% and 56.60% from urban and rural areas, respectively. The percentage values of nematodes important for human health (Toxocara canis, Ancylostomatidae, Trichuris vulpis) remained at the same level (16%). The infected dogs were dominated by a single parasite species, the main was T. canis (28.95%). In total, 54.30% of the soil samples were contaminated with parasite eggs. The contamination of urban and rural sandpits was 40% and 60%, respectively. The molecular examinations of soil samples using LAMP (loop-mediated isothermal amplification) confirmed the presence of nematode eggs of the species T. canis in all samples previously classified as positive PMID:28862690

Impact of paint shop decanter effluents on biological treatability of automotive industry wastewater.

PubMed

Güven, Didem; Hanhan, Oytun; Aksoy, Elif Ceren; Insel, Güçlü; Çokgör, Emine

2017-05-15

A lab-scale Sequencing Batch Reactor (SBR) was implemented to investigate biological treatability and kinetic characteristics of paint shop wastewater (PSW) together with main stream wastewater (MSW) of a bus production factory. Readily biodegradable and slowly biodegradable COD fractions of MWS were determined by respirometric analysis: 4.2% (S S ), 10.4% (S H ) and 59.3% (X S ). Carbon and nitrogen removal performance of the SBR feeding with MSW alone were obtained as 89% and 58%, respectively. When PSW was introduced to MSW, both carbon and nitrogen removal were deteriorated. Model simulation indicated that maximum heterotrophic growth rate decreased from 7.2 to 5.7day -1 , maximum hydrolysis rates were reduced from 6 to 4day -1 (k hS ) and 4 to 1day -1 (k hX ). Based on the dynamic model simulation for the evaluation of nitrogen removal, a maximum specific nitrifier growth rate was obtained as 0.45day -1 for MSW feeding alone. When PSW was introduced, nitrification was completely inhibited and following the termination of PSW addition, nitrogen removal performance was recovered in about 100 days, however with a much lower nitrifier growth rate (0.1day -1 ), possibly due to accumulation of toxic compounds in the sludge. Obviously, a longer recovery period is required to ensure an active nitrifier community. Copyright © 2017 Elsevier B.V. All rights reserved.

The ManureEcoMine pilot installation: advanced integration of technologies for the management of organics and nutrients in livestock waste.

PubMed

Pintucci, Cristina; Carballa, Marta; Varga, Sam; Sarli, Jimena; Peng, Lai; Bousek, Johannes; Pedizzi, Chiara; Ruscalleda, Maël; Tarragó, Elena; Prat, Delphine; Colica, Giovanni; Picavet, Merijn; Colsen, Joop; Benito, Oscar; Balaguer, Marilos; Puig, Sebastià; Lema, Juan M; Colprim, Jesús; Fuchs, Werner; Vlaeminck, Siegfried E

2017-03-01

Manure represents an exquisite mining opportunity for nutrient recovery (nitrogen and phosphorus), and for their reuse as renewable fertilisers. The ManureEcoMine proposes an integrated approach of technologies, operated in a pilot-scale installation treating swine manure (83.7%) and Ecofrit ® (16.3%), a mix of vegetable residues. Thermophilic anaerobic digestion was performed for 150 days, the final organic loading rate was 4.6 kgCOD m -3 d -1 , with a biogas production rate of 1.4 Nm 3 m -3 d -1 . The digester was coupled to an ammonia side-stream stripping column and a scrubbing unit for free ammonia inhibition reduction in the digester, and nitrogen recovery as ammonium sulphate. The stripped digestate was recirculated daily in the digester for 15 days (68% of the digester volume), increasing the gas production rate by 27%. Following a decanter centrifuge, the digestate liquid fraction was treated with an ultrafiltration membrane. The filtrate was fed into a struvite reactor, with a phosphorus recovery efficiency of 83% (as orthophosphate). Acidification of digestate could increment the soluble orthophosphate concentration up to four times, enhancing phosphorus enrichment in the liquid fraction and its recovery via struvite. A synergistic combination of manure processing steps was demonstrated to be technologically feasible to upgrade livestock waste into refined, concentrated fertilisers.

Development of a vinasse nutritive solution for hydroponics.

PubMed

dos Santos, José Darcy; Lopes da Silva, André Luís; da Luz Costa, Jefferson; Scheidt, Gessiel Newton; Novak, Alessandra Cristine; Sydney, Eduardo Bittencourt; Soccol, Carlos Ricardo

2013-01-15

Vinasse is a residue that originates from the distillation of fuel alcohol. However, it contains a relative amount of nutrients. The aim of this work was to develop a nutritive solution using vinasse and to compare it with a commercial solution for the cultivation of lettuce, watercress and rocket. Vinasse obtained from juice must was decanted and filtered, followed by chemical analyses of the nutrients. A nutritive solution composed of 10% vinasse supplemented with nutrients was in agreement with the results of the chemical analyses (a similar amount of Furlani's solution). Experiments were then performed in an NFT (Nutrient film technique) system. The treatments used the vinasse solution and a commercial solution constituted from a Yara Fertilizantes(®) product. The height of the aerial part and the number of leaves of the crops were evaluated at 7, 14, 21, 28, 35 and 42 days. In most crops, the results were very similar. The vinasse solution promoted a larger number of leaves in lettuce and the highest aerial part in watercress. For the rocket, there were no significant differences between the two solutions. In conclusion, a nutritive solution was developed using vinasse, and this solution provided suitable growth, which was higher in some cases, for the crops studied herein. This study shows the great potential of this technology as a rational alternative to vinasse disposal. Copyright © 2012 Elsevier Ltd. All rights reserved.

Bioprocess considerations for expanded-bed chromatography of crude canola extract: sample preparation and adsorbent reuse.

PubMed

Bai, Yun; Glatz, Charles E

2003-03-30

Compared to the conventional microbial and mammalian systems, transgenic plants produce proteins in a different matrix. This provides opportunities and challenges for downstream processing. In the context of the plant host Brassica napus (canola), this work addresses the bioprocessing challenges of solid fractionation, resin fouling by native plant components (e.g., oil, phenolics, etc.), hydrodynamic stability, and resin reuse for expanded bed adsorption for product capture. Plant tissue processing and subsequent protein extraction typically result in an extract with a high content of solids containing a wide particle-size distribution. Without removal of larger particles, the column inlet distributor plugged. The larger particles (> 50 microm) were easily removed through centrifugal settling comparable to that attainable with a scroll decanter. The remaining solids did not affect the column performance. Less than 4% of the lipids and phenolics in the fed extract bound to STREAMLINE trade mark DEAE resin, and this small proportion could be satisfactorily removed using recommended clean-in-place (CIP) procedures. Hydrodynamic expansion and adsorption kinetics of the STREAMLINE trade mark DEAE resin were maintained throughout 10 cycles of reuse, as was the structural integrity of the resin beads. No significant accumulation of N-rich (e.g., proteins) and C/O-rich components (e.g., oil and phenolics) occurred over the same period. Copyright 2003 Wiley Periodicals Inc. Biotechnol Bioeng 81: 775-782, 2003.

Using Helicopter Electromagnetic Surveys to Identify Potential Hazards at Mine Waste Impoundments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammack, R.W.

2008-01-01

In July 2003, helicopter electromagnetic surveys were conducted at 14 coal waste impoundments in southern West Virginia. The purpose of the surveys was to detect conditions that could lead to impoundment failure either by structural failure of the embankment or by the flooding of adjacent or underlying mine works. Specifically, the surveys attempted to: 1) identify saturated zones within the mine waste, 2) delineate filtrate flow paths through the embankment or into adjacent strata and receiving streams, and 3) identify flooded mine workings underlying or adjacent to the waste impoundment. Data from the helicopter surveys were processed to generate conductivity/depthmore » images. Conductivity/depth images were then spatially linked to georeferenced air photos or topographic maps for interpretation. Conductivity/depth images were found to provide a snapshot of the hydrologic conditions that exist within the impoundment. This information can be used to predict potential areas of failure within the embankment because of its ability to image the phreatic zone. Also, the electromagnetic survey can identify areas of unconsolidated slurry in the decant basin and beneath the embankment. Although shallow, flooded mineworks beneath the impoundment were identified by this survey, it cannot be assumed that electromagnetic surveys can detect all underlying mines. A preliminary evaluation of the data implies that helicopter electromagnetic surveys can provide a better understanding of the phreatic zone than the piezometer arrays that are typically used.« less

Variations in the Rate of Infestations of Dogs with Zoonotic Nematodes and the Contamination of Soil in Different Environments.

PubMed

Studzińska, Maria Bernadeta; Demkowska-Kutrzepa, Marta; Borecka, Anna; Meisner, Michał; Tomczuk, Krzysztof; Roczeń-Karczmarz, Monika; Kłapeć, Teresa; Abbass, Zahrai; Cholewa, Alicja

2017-09-01

Companion animals are an important aspect in human life. However, they may also be considered a source of pathogens. An example of zoonotic parasitoses is toxocarosis or cutaneous larva migrans (CLM). The aim of the study was to detect zoonotic nematodes of dogs living in different areas and the intensity of contamination in parasite polluted environments that are hazardous to human health. The fecal samples were examined using standard flotation and decantation methods as well as McMaster's quantitative technique. The soil samples in urban and rural areas were examined using a modified flotation method as described by Quinn et al. Statistical analyses were performed by IBM SPSS Statistics Version 23. The overall prevalence of parasites in dogs was 38%, 17.02% and 56.60% from urban and rural areas, respectively. The percentage values of nematodes important for human health ( Toxocara canis , Ancylostomatidae, Trichuris vulpis ) remained at the same level (16%). The infected dogs were dominated by a single parasite species, the main was T. canis (28.95%). In total, 54.30% of the soil samples were contaminated with parasite eggs. The contamination of urban and rural sandpits was 40% and 60%, respectively. The molecular examinations of soil samples using LAMP (loop-mediated isothermal amplification) confirmed the presence of nematode eggs of the species T. canis in all samples previously classified as positive.

Determination of rhodium in metallic alloy and water samples using cloud point extraction coupled with spectrophotometric technique.

PubMed

Kassem, Mohammed A; Amin, Alaa S

2015-02-05

A new method to estimate rhodium in different samples at trace levels had been developed. Rhodium was complexed with 5-(4'-nitro-2',6'-dichlorophenylazo)-6-hydroxypyrimidine-2,4-dione (NDPHPD) as a complexing agent in an aqueous medium and concentrated by using Triton X-114 as a surfactant. The investigated rhodium complex was preconcentrated with cloud point extraction process using the nonionic surfactant Triton X-114 to extract rhodium complex from aqueous solutions at pH 4.75. After the phase separation at 50°C, the surfactant-rich phase was heated again at 100°C to remove water after decantation and the remaining phase was dissolved using 0.5mL of acetonitrile. Under optimum conditions, the calibration curve was linear for the concentration range of 0.5-75ngmL(-1) and the detection limit was 0.15ngmL(-1) of the original solution. The enhancement factor of 500 was achieved for 250mL samples containing the analyte and relative standard deviations were ⩽1.50%. The method was found to be highly selective, fairly sensitive, simple, rapid and economical and safely applied for rhodium determination in different complex materials such as synthetic mixture of alloys and environmental water samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Clarification of olive mill and winery wastewater by means of clay-polymer nanocomposites.

PubMed

Rytwo, Giora; Lavi, Roy; Rytwo, Yuval; Monchase, Hila; Dultz, Stefan; König, Tom N

2013-01-01

Highly polluted effluents from olive mills and wineries, among others, are unsuitable for discharge into standard sewage-treatment plants due to the large amounts of organic and suspended matter. Efficiency of all management practices for such effluents depends on an effective pretreatment that lowers the amount of suspended solids. Such pretreatments are usually based on three separate stages, taking a total of 2 to 6h: coagulation-neutralizing the colloids, flocculation-aggregating the colloids into larger particles, and separation via filtration or decanting. Previous studies have presented the concept of coagoflocculation based on the use of clay-polymer nanocomposites. This process adds a higher density clay particle to the flocs, accelerating the process to between 15 and 60 min. This study examined suitable nanocomposites based on different clays and polymers. The charge of the compounds increased proportionally to the polymer-to-clay ratio. X-ray diffraction (XRD) measurements indicated that in sepiolite-based nanocomposites there is no change in the structure of the mineral, whereas in smectite-based nanocomposites, the polymer intercalates between the clay layers and increases the spacing depending on the polymer-to-clay ratio. Efficiency of the coagoflocculation process was studied with a dispersion analyzer. Sequential addition of olive mill or winery effluents with a boosting dose of nanocomposites may yield a very efficient and rapid clarification pretreatment. Copyright © 2012 Elsevier B.V. All rights reserved.

Physicochemical characterization of coke-plant soil for the assessment of polycyclic aromatic hydrocarbon availability and the feasibility of phytoremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahn, S.; Werner, D.; Luthy, R.G.

Coke oven site soil was characterized to assess the particle association and availability of polycyclic aromatic hydrocarbons (PAHs). We identified various carbonaceous materials including coal, coke, pitch, and tar decanter sludge. Most of the PAHs were associated with the polymeric matrix of tar sludge or hard pitch as discrete particles, coatings on soil mineral particles, or complex aggregates. The PAH availability from these particles was very low due to hindered diffusive release from solid tar or pitch with apparent diffusivities of 6 x 10{sup -15} for phenanthrene, 3 x 10{sup -15} for pyrene, and 1 x 10{sup -15} cm{sup 2}/smore » for benzo(a)pyrene. Significant concentrations of PAHs were observed in the interior of solid tar aggregates with up to 40,000 mg/kg total PAHs. The release of PAHs from the interior of such particles requires diffusion over a substantial distance, and semipermeable membrane device tests confirmed a very limited availability of PAHs. These findings explain the results from three years of phytoremediation of the site soil, for which no significant changes in the total PAH concentrations were observed in the test plot samples. The observed low bioavailability of PAHs probably inhibited PAH phytoremediation, as diffusion-limited mass transfer would limit the release of PAHs to the aqueous phase.« less

Recovery of Rare Earth Elements and Yttrium from Passive-Remediation Systems of Acid Mine Drainage.

PubMed

Ayora, Carlos; Macías, Francisco; Torres, Ester; Lozano, Alba; Carrero, Sergio; Nieto, José-Miguel; Pérez-López, Rafael; Fernández-Martínez, Alejandro; Castillo-Michel, Hiram

2016-08-02

Rare earth elements and yttrium (REY) are raw materials of increasing importance for modern technologies, and finding new sources has become a pressing need. Acid mine drainage (AMD) is commonly considered an environmental pollution issue. However, REY concentrations in AMD can be several orders of magnitude higher than in naturally occurring water bodies. With respect to shale standards, the REY distribution pattern in AMD is enriched in intermediate and valuable REY, such as Tb and Dy. The objective of the present work is to study the behavior of REY in AMD passive-remediation systems. Traditional AMD passive remediation systems are based on the reaction of AMD with calcite-based permeable substrates followed by decantation ponds. Experiments with two columns simulating AMD treatment demonstrate that schwertmannite does not accumulate REY, which, instead, are retained in the basaluminite residue. The same observation is made in two field-scale treatments from the Iberian Pyrite Belt (IPB, southwest Spain). On the basis of the amplitude of this process and on the extent of the IPB, our findings suggest that the proposed AMD remediation process can represent a modest but suitable REY source. In this sense, the IPB could function as a giant heap-leaching process of regional scale in which rain and oxygen act as natural driving forces with no energy investment. In addition to having environmental benefits of its treatment, AMD is expected to last for hundreds of years, and therefore, the total reserves are practically unlimited.

Limitations of the removal of cyanide from coking wastewater by ozonation and by the hydrogen peroxide-ozone process.

PubMed

Pueyo, N; Miguel, N; Ovelleiro, J L; Ormad, M P

The purpose of this study is to compare the efficiency of ozonation and the hydrogen peroxide-ozone process for the removal of cyanide from coking wastewater. The most efficient oxidation process is combined with coagulation-flocculation-decantation and lime-soda ash softening pretreatments. The oxidation in aqueous solution and industrial wastewater (at pH 9.5-12.3) by O3 was carried out using a range of concentration of consumed O3 from 10 to 290 mg/L. A molar ratio of H2O2/O3 from 0.1 to 5.2 with different concentrations of O3 constants was used for the H2O2-O3 process. The maximum cyanide removal obtained in coking wastewater was 90% using a mass ratio of O3/CN(-) of 9.5. Using lower concentrations of O3, cyanide is not removed and can even be generated due to the presence of other cyanide precursor organic micropollutants in the industrial matrix. The concentration of O3 is reduced to half for the same cyanide removal efficiency if the pretreatments are applied to reduce the carbonate and bicarbonate ions. The cyanide removal efficiency in coking wastewater is not improved if the O3 is combined with the H2O2. However, the preliminary cyanide removal treatment in aqueous solution showed an increase in the cyanide removal efficiency for the H2O2-O3 process.

Natural hazard management high education: laboratory of hydrologic and hydraulic risk management and applied geomorphology

NASA Astrophysics Data System (ADS)

Giosa, L.; Margiotta, M. R.; Sdao, F.; Sole, A.; Albano, R.; Cappa, G.; Giammatteo, C.; Pagliuca, R.; Piccolo, G.; Statuto, D.

2009-04-01

The Environmental Engineering Faculty of University of Basilicata have higher-level course for students in the field of natural hazard. The curriculum provides expertise in the field of prediction, prevention and management of earthquake risk, hydrologic-hydraulic risk, and geomorphological risk. These skills will contribute to the training of specialists, as well as having a thorough knowledge of the genesis and the phenomenology of natural risks, know how to interpret, evaluate and monitor the dynamic of environment and of territory. In addition to basic training in the fields of mathematics and physics, the course of study provides specific lessons relating to seismic and structural dynamics of land, environmental and computational hydraulics, hydrology and applied hydrogeology. In particular in this course there are organized two connected examination arguments: Laboratory of hydrologic and hydraulic risk management and Applied geomorphology. These course foresee the development and resolution of natural hazard problems through the study of a real natural disaster. In the last year, the work project has regarded the collapse of two decantation basins of fluorspar, extracted from some mines in Stava Valley, 19 July 1985, northern Italy. During the development of the course, data and event information has been collected, a guided tour to the places of the disaster has been organized, and finally the application of mathematical models to simulate the disaster and analysis of the results has been carried out. The student work has been presented in a public workshop.

Ryanodine receptors decant internal Ca2+ store in human and bovine airway smooth muscle.

PubMed

Tazzeo, T; Zhang, Y; Keshavjee, S; Janssen, L J

2008-08-01

Several putative roles for ryanodine receptors (RyR) were investigated in human and bovine airway smooth muscle. Changes in intracellular Ca2+ concentration ([Ca2+]i) and membrane current were investigated in single cells by confocal fluorimetry and patch-clamp electrophysiology, respectively, whereas mechanical activity was monitored in intact strips with force transducers. RyR released Ca2+ from the sarcoplasmic reticulum in a ryanodine- and chloroethyl phenol (CEP)-sensitive fashion. Neither ryanodine nor CEP inhibited responses to KCl, cholinergic agonists or serotonin, indicating no direct role for RyR in contraction; in fact, there was some augmentation of these responses. In tissues pre-contracted with carbachol, the concentration-response relationships for isoproterenol and salmeterol were unaffected by ryanodine; relaxations due to a nitric oxide donor were also largely unaffected. Finally, it was examined whether RyR were involved in regulating [Ca2+]i within the subplasmalemmal space using patch-clamp electrophysiology as well as Ca2+ fluorimetry: isoproterenol increased [Ca2+]i- and Ca2+-dependent K+ current activity in a ryanodine-sensitive fashion. In conclusion, ryanodine receptors in airway smooth muscle are not important in directly mediating contraction or relaxation. The current authors speculate instead that these allow the sarcoplasmic reticulum to release Ca2+ towards the plasmalemma (to unload an overly full Ca2+ store and/or increase the Ca2+-buffering capacity of the sarcoplasmic reticulum) without affecting bronchomotor tone.

Effect of the corn breaking method on oil distribution between stillage phases of dry-grind corn ethanol production.

PubMed

Wang, H; Wang, T; Johnson, L A; Pometto, A L

2008-11-12

The majority of fuel ethanol in the United States is produced by using the dry-grind corn ethanol process. The corn oil that is contained in the coproduct, distillers' dried grains with solubles (DDGS), can be recovered for use as a biodiesel feedstock. Oil removal will also improve the feed quality of DDGS. The most economical way to remove oil is considered to be at the centrifugation step for separating thin stillage (liquid) from coarse solids after distilling the ethanol. The more oil there is in the liquid, the more it can be recovered by centrifugation. Therefore, we studied the effects of corn preparation and grinding methods on oil distribution between liquid and solid phases. Grinding the corn to three different particle sizes, flaking, flaking and grinding, and flaking and extruding were used to break up the corn kernel before fermentation, and their effects on oil distribution between the liquid and solid phases were examined by simulating an industrial decanter centrifuge. Total oil contents were measured in the liquid and solids after centrifugation. Dry matter yield and oil partitioning in the thin stillage were highly positively correlated. Flaking slightly reduced bound fat. The flaked and then extruded corn meal released the highest amount of free oil, about 25% compared to 7% for the average of the other treatments. The freed oil from flaking, however, became nonextractable after the flaked corn was ground. Fine grinding alone had little effect on oil partitioning.

POTENTIAL IMPACT OF TANK F FLUSH SOLUTION ON H-CANYON EVAPORATOR OPERATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyser, E.; Fondeur, F.; Fink, S.

2010-09-13

Previous chemical analysis of a sample from the liquid heel found in Tank F of the High Activity Drain (HAD) system in F/H laboratory revealed the presence of n-paraffin, tributyl phosphate (TBP), Modifier from the Modular Caustic-Side Solvent Extraction Unit (MCU) process and a vinyl ester resin that is very similar to the protective lining on Tank F. Subsequent analyses detected the presence of a small amount of diisopropylnaphthalene (DIN) (major component of Ultima Gold{trademark} AB liquid scintillation cocktail). Indications are that both vinyl ester resin and DIN are present in small amounts in the flush solution. The flush solutionmore » currently in the LR-56S trailer likely has an emulsion which is believed to contain a mixture of the reported organic species dominated by TBP. An acid treatment similar to that proposed to clear the HAD tank heel in F/H laboratory was found to allow separation of an organic phase from the cloudy sample tested by SRNL. Mixing of that clear sample did re-introduce some cloudiness that did not immediately clear but that cloudiness is attributed to the DIN in the matrix. An organic phase does quickly separate from the cloudy matrix allowing separation by a box decanter in H-Canyon prior to transfer to the evaporator feed tank. This separation should proceed normally as long as the emulsion is broken-up by acidification.« less

A quick and simple method, usable in the field, for collecting parasites in suitable condition for both morphological and molecular studies.

PubMed

Justine, Jean-Lou; Briand, Marine J; Bray, Rodney A

2012-07-01

Many methods have been proposed for collecting and fixing parasites, but most were written before the molecular age, and were intended to be practised by experienced parasitologists in well-equipped laboratories. We describe here a very simple method, illustrated by photographs, for collecting helminths from the digestive tract of vertebrates. It only requires a few plastic vials, some ethanol and a means to heat water. Basically, the method consists of: (a) the extraction of all organs from the abdominal cavity; (b) opening the digestive system longitudinally; (c) agitate gut and contents in a saline solution (i.e. ca. 9% NaCl or 1/4 sea water in tap water); (d) decant in saline as many times as needed to clean contents; (e) immediately fix parasites in near-boiling saline; (f) discard saline and keep specimens in 95% ethanol. Additional information is given for collecting parasites from fish gills with a similar process. The method will collect most helminths (digeneans, larval cestodes, nematodes, acanthocephalans) from the digestive tract, and monogeneans and isopod and copepod crustaceans from fish gills. The specimens will be suitable for both morphological study and DNA sequencing. The method is simple, fast, inexpensive and can be used by untrained personnel, even in the field without electricity and without a binocular microscope. It can also be used by trained parasitologists who need to expedite treatment of abundant samples.

Diffusion-regulated phase-transfer catalysis for atom transfer radical polymerization of methyl methacrylate in an aqueous/organic biphasic system.

PubMed

Ding, Mingqiang; Jiang, Xiaowu; Peng, Jinying; Zhang, Lifen; Cheng, Zhenping; Zhu, Xiulin

2015-03-01

A concept based on diffusion-regulated phase-transfer catalysis (DRPTC) in an aqueous-organic biphasic system with copper-mediated initiators for continuous activator regeneration is successfully developed for atom transfer radical polymerization (ICAR ATRP) (termed DRPTC-based ICAR ATRP here), using methyl methacrylate (MMA) as a model monomer, ethyl α-bromophenylacetate (EBrPA) as an initiator, and tris(2-pyridylmethyl)amine (TPMA) as a ligand. In this system, the monomer and initiating species in toluene (organic phase) and the catalyst complexes in water (aqueous phase) are simply mixed under stirring at room temperature. The trace catalyst complexes transfer into the organic phase via diffusion to trigger ICAR ATRP of MMA with ppm level catalyst content once the system is heated to the polymerization temperature (75 °C). It is found that well-defined PMMA with controlled molecular weights and narrow molecular weight distributions can be obtained easily. Furthermore, the polymerization can be conducted in the presence of limited amounts of air without using tedious degassed procedures. After cooling to room temperature, the upper organic phase is decanted and the lower aqueous phase is reused for another 10 recycling turnovers with ultra low loss of catalyst and ligand loading. At the same time, all the recycled catalyst complexes retain nearly perfect catalytic activity and controllability, indicating a facile and economical strategy for catalyst removal and recycling. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficacy and toxicity of formalin solutions containing paraformaldehyde for fish and egg treatments

USGS Publications Warehouse

Howe, G.E.; Marking, L.L.; Bills, T.D.; Schreier, Theresa M.

1995-01-01

Formalin used for fish and egg treatments at hatcheries often develops a white precipitate called paraformaldehyde when stored at low temperatures. This presents a problem for hatchery managers because most of the literature and treatment procedures claim that formalin containing paraformaldehyde is more toxic than pure formalin and is not safe for fish or egg treatments. Acute toxicity tests with rainbow trout (Oncorhynchus mykiss) and channel catfish (Ictalurus punctatus) showed that the toxicity of formalin solutions containing a moderate amount of fine paraformaldehyde was similar to that of pure formalin. In efficacy tests on fish eggs, the bottom fraction of a formalin solution containing paraformaldehyde and a sample from the clear top fraction were equally effective in controlling fungal infection on rainbow trout eggs and caused no treatment-related mortality. Chemical assays found on average a 3% difference in formaldehyde concentration between top and bottom fractions of a formalin solution containing paraformaldehyde. We recommend normal use of formalin solutions containing light to moderate amounts of fine paraformaldehyde. Allowing solutions to warm to room temperature may resolubilize moderate amounts of paraformaldehyde if the exposure to cold was not prolonged. If precipitation is heavier, clear top fractions can be decanted and used as normal because paraformaldehyde settles to the bottom of containers. Formalin solutions that have been exposed to freezing temperatures for long periods (more than 6 weeks) and have developed large amounts of paraformaldehyde solids should not be used and resolubilization by warming is not possible. Formation of paraformaldehyde in formalin solutions can be easily avoided by storing formalin at room temperature.

Acetone-butanol fermentation of lignocellulosic hydrolysates for the butanol production

NASA Astrophysics Data System (ADS)

Morozova, Tatyana; Semyonov, Sergey

2017-11-01

It is known that the use of lignocellulosic hydrolysates reduces the production cost of biofuel such as biobutanol and bioethanol. But for the most successful application of the hydrolysates for the biofuel production, it is necessary to apply an inexpensive and effective detoxification method and to use of cost-effective growth factors. In the present study, we evaluated the use of an acid hydrolysate of spruce and an enzymatic hydrolysate of miscanthus cellulose for the biobutanol production. To remove inhibitors from the hydrolysates, we applied the traditional physicochemical method with overliming and the biodetoxification method based on the use of the specially adapted activated sludge. Calcium hydroxide (150 g/L) was used for the neutralization. The biological method of detoxification of lignocellulosic hydrolysates was carried out under non-sterile conditions at room temperature by the specially adapted activated sludge of the urban wastewater treatment plants. The acetone-butanol fermentation was carried out by a strain of bacteria Clostridium acetobutylicum ATCC 824. The treatment by overliming removed 84-85 % and 83-86% of 5-hydroxymethylfurfural (5-HMF) and furfural from the hydrolysates respectively. Using the method of biodetoxification the content of furfural decreased by 98% and concentration of 5-HMF - by 97-99%. In the present study as an inexpensive source of growth substances for the fermentation of the hydrolysates it has been suggested to use decantate of the brewer's spent grain. The obtained results showed that the brewer's spent grain can be used in the biofuel production as efficiently as the synthetic growth substances.

Evaluation of the toxic potential of coffee wastewater on seeds, roots and meristematic cells of Lactuca sativa L.

PubMed

Aguiar, Luara Louzada; Andrade-Vieira, Larissa Fonseca; de Oliveira David, José Augusto

2016-11-01

Coffee wastewater (CWW) is an effluent produced through wet processing of coffee containing high concentration of organic matter, nutrients, salts and also agrochemicals. It is released directly into the argillaceous soil or into decantation tanks for later disposal into soils, by fertigation, subsurface infiltration or superficial draining. However, this practice is not followed by the monitoring the toxicity potential of this effluent. In this sense, the present work aimed to evaluate the phytotoxic, cytogenotoxic and mutagenic potential of CWW on seed germination, root elongation and cell cycle alterations in the plant model Lactuca sativa L. The effluent (CWW) collected was diluted in distilled water into six concentrations solutions (1.25%, 1.66%, 2.5%, 5.0%, 10%, 20%). A solution of raw CWW (100%) was also applied. Distilled water was used as negative control), and the DNA alkylating agent, metilmetano sulfonate (4×10(-4)M) as positive control. Physico-chemical parameters of the CWW was accessed and it was found that the effluent contained total phenols and inorganic matter in amounts within the limits established by the National Environment Council (CONAMA). Nevertheless, the biologicals assays performed demonstrated the phytotoxicity and cytogenotoxicty of CWW. Seed germination was totally inhibited after exposure of raw CWW. In addition, a decrease in seed germination speed as well as in root growth dose-dependently manner was noticed. Moreover, nuclear and chromosomal alterations were observed in the cell cycle, mostly arising from aneugenic action. Copyright © 2016 Elsevier Inc. All rights reserved.

Barriers to mesalamine adherence in patients with inflammatory bowel disease: a qualitative analysis.

PubMed

Devlen, Jennifer; Beusterien, Kathleen; Yen, Linnette; Ahmed, Awais; Cheifetz, Adam S; Moss, Alan C

2014-03-01

The causes for nonadherence to mesalamine in patients with inflammatory bowel disease (IBD) have been characterized using mostly indirect methods. Patient-reported barriers are lacking in this population. To identify patient-reported barriers to mesalamine adherence through direct interviews. Focus groups and one-on-one interviews were undertaken in adult patients with IBD. Transcripts from the focus groups and interviews were analyzed to identify themes and links between these themes, assisted by qualitative data software MaxQDA. Of 27 patients participating, 21 (78%) had ulcerative colitis, and 6 (22%) had Crohn's disease. Their self-reported adherence ranged from complete adherence (n = 3) to intermittent nonadherence (n = 24). Patients frequently indicated that they were resistant to taking medications for their condition. The barriers to adherence that emerged from interviews could be categorized under a number of themes: competing priorities, social stigma, refill inconvenience, costs, efficacy values, side effects, and pill characteristics. Efficacy values reported to influence adherence included doubts about efficacy, consequences of missed doses, and doubts about need for maintenance medication. Pill characteristics reported as barriers included pill size and pill frequency. Despite use of electronic prescribing, obtaining refills was reported as an obstacle to adherence in this cohort. Decanting of pills to multiple containers to increase accessibility was also reported. Patients with both ulcerative colitis and Crohn's disease report a number of common barriers to mesalamine adherence. Factors in medication-taking behavior and beliefs were reported in this study that may have implications for strategies to improve adherence by health care providers.

Glacial origin for cave rhythmite during MIS 5d-c in a glaciokarst landscape, Picos de Europa (Spain)

NASA Astrophysics Data System (ADS)

Ballesteros, Daniel; Jiménez-Sánchez, Montserrat; Giralt, Santiago; DeFelipe, Irene; García-Sansegundo, Joaquín

2017-06-01

Laminated slackwater deposits have been identified in many karst caves related to fluvial and lacustrine sedimentation. However, sedimentological evidence rarely supports a glacial origin for these deposits, which was proposed by previous studies. The Torca La Texa shaft is located in a glaciokarst area that comprises numerous slackwater-type deposits, piled up in fining-upward sequences. A basal sandy erosive layer and millimeter-sized laminated rhythmite with interbedded flowstone characterize these sequences. Fining-upward layers of carbonate silt, clay, and minor quartz sand deposited in flooded conduits define the rhythmite lamination. The presence of allochthonous minerals indicates that the rhythmite sediment comes from the glacial erosion of nearby carbonate mountains. Two 234U/230Th radiometric ages dated the rhythmite deposits around 109 and 95 ka, coinciding with relative cold periods included in the MIS 5d-c. These cold periods were marked by a high annual seasonality, immediately after the glacial local maximum extension, in agreement with a varve-type deposit. The combination of these sedimentological mineralogical, geomorphological and paleoclimate information indicates that the rhythmite should be introduced into the studied cave during the summer melting of the glaciers, which produced the recharge of the karst aquifer, triggering cave floods. In addition, punctual glacier collapses would also have their imprint in the slackwater sequences with thicker, coarser and erosive sand deposits and the spring blocking by glaciers may have promoted floods inside the cave. Therefore, the studied rhythmite can be interpreted as glacial varves decanted during the relatively cold climate conditions.

Selective enrichment of a methanol-utilizing consortium using pulp & paper mill waste streams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregory R. Mockos; William A. Smith; Frank J. Loge

Efficient utilization of carbon inputs is critical to the economic viability of the current forest products sector. Input carbon losses occur in various locations within a pulp mill, including losses as volatile organics and wastewater . Opportunities exist to capture this carbon in the form of value-added products such as biodegradable polymers. Waste activated sludge from a pulp mill wastewater facility was enriched for 80 days for a methanol-utilizing consortium with the goal of using this consortium to produce biopolymers from methanol-rich pulp mill waste streams. Five enrichment conditions were utilized: three high-methanol streams from the kraft mill foul condensatemore » system, one methanol-amended stream from the mill wastewater plant, and one methanol-only enrichment. Enrichment reactors were operated aerobically in sequencing batch mode at neutral pH and 25°C with a hydraulic residence time and a solids retention time of four days. Non-enriched waste activated sludge did not consume methanol or reduce chemical oxygen demand. With enrichment, however, the chemical oxygen demand reduction over 24 hour feed/decant cycles ranged from 79 to 89 %, and methanol concentrations dropped below method detection limits. Neither the non-enriched waste activated sludge nor any of the enrichment cultures accumulated polyhydroxyalkanoates (PHAs) under conditions of nitrogen sufficiency. Similarly, the non-enriched waste activated sludge did not accumulate PHAs under nitrogen limited conditions. By contrast, enriched cultures accumulated PHAs to nearly 14% on a dry weight basis under nitrogen limited conditions. This indicates that selectively-enriched pulp mill waste activated sludge can serve as an inoculum for PHA production from methanol-rich pulp mill effluents.« less

Managing ochratoxin A risk in the grape-wine food chain.

PubMed

Visconti, Angelo; Perrone, Giancarlo; Cozzi, Giuseppe; Solfrizzo, Michele

2008-02-01

The main source of ochratoxin A (OTA) in the wine food chain is the infection of grapes by "black aspergilli" in the field. OTA-producing black aspergilli include principally Aspergillus carbonarius, followed by A. niger and possibly A. tubingensis. They are opportunistic fungi that develop particularly on damaged berries at ripening, although they may occur and form OTA on grapes from veraison to harvest. Climatic conditions (high humidity and temperature) and geographical location are important factors favouring OTA accumulation in grape berries. The severity of aspergillus rot is influenced by excessive irrigation and rainfall prior to harvest, which causes berry splitting. In addition, berry wounds caused by insect attack provide preferential entries for black aspergilli. High OTA levels occur in grapes severely damaged by the grape moth, Lobesia botrana, particularly in Mediterranean areas. Some grape varieties display greater susceptibility to aspergillus rot due to intrinsic genetic characteristics and bunch conformation (i.e. compact>sparse). Control measures for toxigenic mycoflora in the vineyards must consider these critical control points. Proper fungicidal and insecticidal treatments can reduce OTA contamination. Nevertheless, knowledge about the fate of OTA and its distribution in wine and winery by-products is important to manage OTA risk in contaminated stock. In our wine-making experiments, only 4% of the OTA present in grapes remained in the wine--the majority is retained in pressed grape pomaces. OTA concentration remained unchanged in wine after a 1-year aging as well as in all liquid fractions collected during vinification (i.e. must, free run wine, and wine after first and second decantation). Activated carbon can reduce OTA levels in wine but negatively affects wine quality.

Comparative Toxicity of Preservatives on Immortalized Corneal and Conjunctival Epithelial Cells

PubMed Central

Ahdoot, Michael; Marcus, Edward; Asbell, Penny A.

2009-01-01

Abstract Purpose Nearly all eye drops contain preservatives to decrease contamination. Nonpreservatives such as disodium-ethylene diamine tetra-acetate (EDTA) and phosphate-buffered saline are also regularly added as buffering agents. These components can add to the toxicity of eye drops and cause ocular surface disease. To evaluate the potential toxicity of these common components and their comparative effects on the ocular surface, a tissue culture model utilizing immortalized corneal and conjunctival epithelial cells was utilized. Methods Immortalized human conjunctival and corneal epithelial cells were grown. At confluency, medium was replaced with 100 μL of varying concentrations of preservatives: benzalkonium chloride (BAK), methyl paraben (MP), sodium perborate (SP), chlorobutanol (Cbl), and stabilized thimerosal (Thi); varying concentrations of buffer: EDTA; media (viable control); and formalin (dead control). After 1 h, solutions were replaced with 150 μL of MTT (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl tetrazonium bromide). After 4 h, solutions decanted, 100 μL of acid isopropanol added, and the optical density determined at 572 nm to evaluate cell viability. Results Conjunctival and corneal cell toxicity was seen with all preservatives. Depending upon concentration, BAK exhibited from 56% to 89% toxicity. In comparison, Cbl exhibited from 50% to 86%, MP from 30% to 76%, SP from 23% to 59%, and Thi from 70% to 95%. EDTA with minimal toxicity (from 6% to 59%) was indistinguishable from SP. Conclusions Generally, the order of decreasing toxicity at the most commonly used concentrations: Thi (0.0025%) > BAK (0.025%) > Cbl (0.25%) > MP (0.01%) > SP (0.0025%) ≈ EDTA (0.01%). Even at low concentration, these agents will cause some degree of ocular tissue damage. PMID:19284328

New sorbent in the dispersive solid phase extraction step of quick, easy, cheap, effective, rugged, and safe for the extraction of organic contaminants in drinking water treatment sludge.

PubMed

Cerqueira, Maristela B R; Caldas, Sergiane S; Primel, Ednei G

2014-04-04

Recent studies have shown a decrease in the concentration of pesticides, pharmaceuticals and personal care products (PCPs) in water after treatment. A possible explanation for this phenomenon is that these compounds may adhere to the sludge; however, investigation of these compounds in drinking water treatment sludge has been scarce. The sludge generated by drinking water treatment plants during flocculation and decantation steps should get some special attention not only because it has been classified as non-inert waste but also because it is a very complex matrix, consisting essentially of inorganic (sand, argil and silt) and organic (humic substances) compounds. In the first step of this study, three QuEChERS methods were used, and then compared, for the extraction of pesticides (atrazine, simazine, clomazone and tebuconazole), pharmaceuticals (amitriptyline, caffeine, diclofenac and ibuprofen) and PCPs (methylparaben, propylparaben, triclocarban and bisphenol A) from drinking water treatment sludge. Afterwards, the study of different sorbents in the dispersive solid phase extraction (d-SPE) step was evaluated. Finally, a new QuEChERS method employing chitin, obtained from shrimp shell waste, was performed in the d-SPE step. After having been optimized, the method showed limits of quantification (LOQ) between 1 and 50 μg kg(-1) and the analytical curves showed r values higher than 0.98, when liquid chromatography tandem mass spectrometry was employed. Recoveries ranged between 50 and 120% with RSD≤15%. The matrix effect was evaluated and compensated with matrix-matched calibration. The method was applied to drinking water treatment sludge samples and methylparaben and tebuconazole were found in concentration

Low-energy route for alcohol/gasohol recovery from fermentor beer. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mix, T.W.

1982-03-01

The production of gasohol directly from fermentor beer and gasoline is feasible and will enable a major reduction in the energy requirements for gasohol production. The fermentor beer is first enriched in a beer still to a 69 mol % ethanol, 31 mol % water product which is then dehydrated by extractive distillation with gasoline as the extractive agent. Gasohol is produced directly. In one version of the process, a heavy cut of gasoline, presumed available at a refinery before blending in of light components, is used as the extractive agent. The enriching column overhead vapors are used to reboilmore » the extractive distillation and steam stripping columns and to contribute to the preheating of the fermentor beer feed. Light components are blended into the heavy cut-ethanol bottom product from the extractive distillation column to form the desired gasohol. Energy requirements, including feed preheat, are 11,000 Btu per gallon of ethanol in the product gasohol. One hundred and fifty pound steam is required. In a second version, full range gasoline is used as the extractive agent. The enriching column overhead vapors are again used to reboil the extractive distillation and steam stripping columns and to contribute to the preheating of the fermentor beer feed. Light gasoline components recovered from the decanter following the overhead condenser of the extractive distillation column are blended in with the gasoline-ethanol product leaving the bottom of the extractive distillation column to form the desired gasohol. Energy requirements in this case are 13,000 Btu/gallon of ethanol in the product gasohol. In both of the above cases it is energy-conservative and desirable from a process standpoint to feed the enriched alcohol to the extractive distillation column as a liquid rather than as a vapor.« less

Plant-available and water-soluble phosphorus in soils amended with separated manure solids.

PubMed

Gasser, M-O; Chantigny, M H; Angers, D A; Bittman, S; Buckley, K E; Rochette, P; Massé, D

2012-01-01

Physical, chemical, or biological treatment of animal liquid manure generally produces a dry-matter rich fraction (DMF) that contains most of the initial phosphorus (P). Our objective was to assess the solubility and plant availability of P from various DMFs as a function of soil P status. Eight different DMFs were obtained from liquid swine (LSM) and dairy cattle (LDC) manures treated by natural decantation, anaerobic digestion, chemical flocculation, composting, or mechanical separation. The DMFs were compared with mineral P fertilizer in a pot experiment with oat ( L.) grown in four soils with varied P-fixing capacities and P saturation levels. The DMFs were added at a rate of 50 mg P kg soil and incubated 14 d before seeding. Soil water-extractable P (P) at all water:soil extraction ratios (2:1, 20:1, and 200:1) was slightly higher when DMFs were derived from LDC rather than LSM. Soil P at the 2:1 ratio was lower with anaerobically digested LSM. At the 2:1 extraction ratio, DMF P was less soluble than mineral P as P saturation in soils increased. In soils with a lower P-fixing capacity, DMF P appeared less water soluble than mineral P under 20:1 and 200:1 extraction ratios. After 72 d of plant growth, DMFs produced yields comparable to mineral P fertilizer. Although the plant availability of P from DMFs was comparable to mineral P fertilizer, P from DMFs could be less vulnerable to leaching or runoff losses in soils with a high P saturation level or low P-fixing capacity. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buzra, Urim, E-mail: rimibuzra@yahoo.com; Berberi, Pellumb; Mitrushi, Driada

Change of irradiative properties of the atmosphere during clear days is an indicator, among others, of existence of atmospheric aerosols and can be used as an indicator for assessment both air pollution and local modifications of solar energy potentials. The main objective of this study is estimation of influence of anthropogenic aerosols on solar energy falling in a horizontal surface during a cloudless day. We have analyzed and quantified the effect of aerosols on reducing the amount of solar energy that falls on the horizontal ground surface in cloudless sky conditions, estimating temporal evolution, both in daily and hour scale,more » considering also, side effects caused by relative humidity of the air wind speed and geometric factor. As an indicator of concentration of aerosols in atmosphere, we agreed to use the attenuation of solar radiation after the last rainy day. All data were corrected by factors such as, variations of relative humidity, wind speed and daily change of incident angle of solar radiation. We studied the change of solar insolation in three sites with different traffic intensity, one in city of Shkodra and two in city of Tirana. Fifteen days after last rainy day, approximate time needed to achieve saturation, the insolation drops only 3.1% in the city of Shkodra, while in two sites in city of Tirana are 8.5 % and 18.4%. These data show that reduction of solar insolation is closely related with anthropogenic activity, mainly traffic around the site of the meteorological station. The day to day difference tends to decrease with increasing of number of days passed from the last rainy day, which is an evidence of a trend toward a dynamic equilibrium between decantation process of aerosols during the night and their generation during the day.« less

Developing procedures for the large-scale purification of human serum butyrylcholinesterase.

PubMed

Saxena, Ashima; Luo, Chunyuan; Doctor, Bhupendra P

2008-10-01

Human serum butyrylcholinesterase (Hu BChE) is the most viable candidate for the prophylactic treatment of organophosphate poisoning. A dose of 200 mg/70 kg is predicted to protect humans against 2x LD(50) of soman. Therefore, the aim of this study was to develop procedures for the purification of gram quantities of this enzyme from outdated human plasma or Cohn Fraction IV-4. The purification of Hu BChE was accomplished by batch adsorption on procainamide-Sepharose-CL-4B affinity gel followed by ion-exchange chromatography on a DEAE-Sepharose column. For the purification of enzyme from Cohn Fraction IV-4, it was resuspended in 25 mM sodium phosphate buffer, pH 8.0, and fat was removed by decantation, prior to batch adsorption on procainamide-Sepharose gel. In both cases, the procainamide gel was thoroughly washed with 25 mM sodium phosphate buffer, pH 8.0, containing 0.05 M NaCl, and the enzyme was eluted with the same buffer containing 0.1 M procainamide. The enzyme was dialyzed and the pH was adjusted to 4.0 before loading on the DEAE column equilibrated in sodium acetate buffer, pH 4.0. The column was thoroughly washed with 25 mM sodium phosphate buffer, pH 8.0 containing 0.05 M NaCl before elution with a gradient of 0.05-0.2M NaCl in the same buffer. The purity of the enzyme following these steps ranged from 20% to 40%. The purity of the enzyme increased to >90% by chromatography on an analytical procainamide affinity column. Results show that Cohn Fraction IV-4 is a much better source than plasma for the large-scale isolation of purified Hu BChE.

Detection limit of Mycobacterium chimaera in water samples for monitoring medical device safety: insights from a pilot experimental series.

PubMed

Schreiber, P W; Köhler, N; Cervera, R; Hasse, B; Sax, H; Keller, P M

2018-07-01

A growing number of Mycobacterium chimaera infections after cardiosurgery have been reported by several countries. These potentially fatal infections were traced back to contaminated heater-cooler devices (HCDs), which use water as a heat transfer medium. Aerosolization of water contaminated with M. chimaera from HCDs enables airborne transmission to patients undergoing open chest surgery. Infection control teams test HCD water samples for mycobacterial growth to guide preventive measures. The detection limit of M. chimaera in water samples, however, has not previously been investigated. To determine the detection limit of M. chimaera in water samples using laboratory-based serial dilution tests. An M. chimaera strain representative of the international cardiosurgery-associated M. chimaera outbreak was used to generate a logarithmic dilution series. Two different water volumes, 50 and 1000mL, were inoculated, and, after identical processing (centrifugation, decantation, and decontamination), seeded on mycobacteria growth indicator tube (MGIT) and Middlebrook 7H11 solid media. MGIT consistently showed a lower detection limit than 7H11 solid media, corresponding to a detection limit of ≥1.44 × 10 4 cfu/mL for 50mL and ≥2.4cfu/mL for 1000mL water samples. Solid media failed to detect M. chimaera in 50mL water samples. Depending on water volume and culture method, major differences exist in the detection limit of M. chimaera. In terms of sensitivity, 1000mL water samples in MGIT media performed best. Our results have important implications for infection prevention and control strategies in mitigation of the M. chimaera outbreak and healthcare water safety in general. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Clinical Evaluation of a Safety-device to Prevent Urinary Catheter Inflation Related Injuries.

PubMed

Davis, Niall F; Cunnane, Eoghan M; Mooney, Rory O'C; Forde, James C; Walsh, Michael T

2018-05-01

To evaluate the feasibility of a novel "safety-valve" device for preventing catheter related urethral trauma during urethral catheterization (UC). To assess the opinions of clinicians on the performance of the safety-valve device. A validated prototype "safety-valve" device for preventing catheter balloon inflation related urethral injuries was prospectively piloted in male patients requiring UC in a tertiary referral teaching hospital (n = 100). The device allows fluid in the catheter system to decant through an activated safety threshold pressure valve if the catheter anchoring balloon is misplaced. Users evaluated the "safety-valve" with an anonymous questionnaire. The primary outcome measurement was prevention of anchoring balloon inflation in the urethra. Secondary outcome measurement was successful inflation of urinary catheter anchoring balloon in the bladder. Patient age was 76 ± 12 years and American Society of Anaesthesiologists grade was 3 ± 1.4. The "safety-valve" was utilized by 34 clinicians and activated in 7% (n = 7/100) patients during attempted UC, indicating that the catheter anchoring balloon was incorrectly positioned in the patient's urethra. In these 7 cases, the catheter was successfully manipulated into the urinary bladder and inflated. 31 of 34 (91%) clinicians completed the questionnaire. Ten percent (n = 3/31) of respondents had previously inflated a urinary catheter anchoring balloon in the urethra and 100% (n = 31) felt that a safety mechanism for preventing balloon inflation in the urethra should be compulsory for all UCs. The safety-valve device piloted in this clinical study offers an effective solution for preventing catheter balloon inflation related urethral injuries. Copyright © 2018 Elsevier Inc. All rights reserved.

ICU-acquired candidemia within selective digestive decontamination studies: a meta-analysis.

PubMed

Hurley, James C

2015-11-01

To estimate the direct and indirect (contextual) effects of the factorized constituents of selective digestive decontamination and selective oropharyngeal decontamination (SDD/SOD), being topical antibiotic (TA) and protocolized antifungal prophylaxis (PAFP), on ICU-acquired candidemia. A broad range of ICU candidemia incidence studies were sourced to serve as points of reference. The candidemia incidence was extracted from component (control and intervention) groups decanted from studies of various designs (concurrent or non-concurrent) and whether investigating SDD/SOD versus non-TA methods of ICU infection prevention. The candidemia incidences were summarized in regression models using generalized estimating equation (GEE) methods. Groups derived from observational studies (no prevention method under study) provided an overarching external benchmark candidemia incidence for calibration. Within studies investigating SDD/SOD, the mean (and 95% confidence interval) candidemia incidence among concurrent component groups (40 control; 2.4%; 1.7-3.2% and 43 intervention groups; 2.4%; 1.6-3.1%), but not non-concurrent control groups (11 groups; 1.6%; 0.1-2.7%), is higher than that of the benchmark candidemia incidence derived from 54 observational groups (1.5%; 1.2-1.9%). The TA constituent within SDD/SOD has significant direct and indirect (contextual) effects in GEE models even after adjusting for the publication year and the group-wide presence of either candidemia risk factors or PAFP use. The TA constituent of SDD/SOD is associated with a contextual effect on candidemia incidence which is similar in magnitude to that of the conventional candidemia risk factors and against which PAFP partially attenuates. This increase is inapparent within individual SDD/SOD studies examined in isolation.

Chemistry of a low temperature geothermal reservoir: The Triassic sandstone aquifer at Melleray, FR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuataz, Francois-David; Fouillac, Christian; Detoc, Aylvie

1988-01-01

The Triassic sandstone aquifer offers on a regional scale, a large potential for low-temperature geothermal exploitation in the Paris Basin. The Na-Cl water n the aquifer has highly variable mineralization (TDS = 4 to 110 g/l) and a wide range of temperature (50º to >100ºC). Chemical studies have been carried out on the Melleray site near Orléans, where a single wel was producing a Na-Cl geothermal water (TDS = 35 g/l) at a wellhead temperature of 72ºC to provide heat for greenhouses. The purpose of these studies is to understand the chemical phenomena occurring in the geothermal loop and tomore » determine the treatment of the fluid and the exploitation procedures necessary for proper reinjection conditions to be achieved. During the tests performed after the drilling operations, chemical variations in the fluid were noticed between several producing zones in the aquifer. Daily geochemical monitoring of the fluid was carried out during two periods of differing exploitation conditions, respectively pumping at 148 m{sup 3}/h and artesian flow at 36 m{sup 3}/h. Vertical heterogeneities of the aquifer can explain the variations observed for the high flowrate. Filtration experiments revealed that the particle load varies with the discharge rate and that over 95 weight % of the particles are smaller than 1 micrometer. The chemistry of the particles varies greatly, according to their origin as corrosion products from the well casing, particles drawn out of the rock or minerals newly formed through water-rock reactions. Finally, small-scale oxidation experiments were carried out on the geothermal fluid to observe the behavior of Fe and SiO{sub 2} and to favour particle aggregates for easier filtration or decantation processes.« less

Selective Enrichment of a Methanol-Utilizing Consortium Using Pulp and Paper Mill Waste Streams

NASA Astrophysics Data System (ADS)

Mockos, Gregory R.; Smith, William A.; Loge, Frank J.; Thompson, David N.

Efficient utilization of carbon inputs is critical to the economic viability of the current forest products sector. Input carbon losses occur in various locations within a pulp mill, including losses as volatile organics and wastewater. Opportunities exist to capture this carbon in the form of value-added products such as biodegradable polymers. Wasteactivated sludge from a pulp mill wastewater facility was enriched for 80 days for a methanol-utilizing consortium with the goal of using this consortium to produce biopolymers from methanol-rich pulp mill waste streams. Five enrichment conditions were utilized: three high-methanol streams from the kraft mill foul condensate system, one methanol-amended stream from the mill wastewater plant, and one methanol-only enrichment. Enrichment reactors were operated aerobically in sequencing batch mode at neutral pH and 25°C with a hydraulic residence time and a solids retention time of 4 days. Non-enriched waste activated sludge did not consume methanol or reduce chemical oxygen demand. With enrichment, however, the chemical oxygen demand reduction over 24-h feed/ decant cycles ranged from 79 to 89%, and methanol concentrations dropped below method detection limits. Neither the non-enriched waste-activated sludge nor any of the enrichment cultures accumulated polyhydroxyalkanoates (PHAs) under conditions of nitrogen sufficiency. Similarly, the non-enriched waste activated sludge did not accumulate PHAs under nitrogen-limited conditions. By contrast, enriched cultures accumulated PHAs to nearly 14% on a dry weight basis under nitrogen-limited conditions. This indicates that selectively enriched pulp mill waste activated sludge can serve as an inoculum for PHA production from methanol-rich pulp mill effluents.

Diclofenac degradation by heterogeneous photocatalysis with Fe3O4/Ti x O y /activated carbon fiber composite synthesized by ultrasound irradiation

NASA Astrophysics Data System (ADS)

Moreno-Valencia, E. I.; Paredes-Carrera, S. P.; Sánchez-Ochoa, J. C.; Flores-Valle, S. O.; Avendaño-Gómez, J. R.

2017-11-01

In this work, a photocatalytic system to degrade diclofenac was developed using a composite Fe3O4/Ti x O y on an activated carbon fiber. Diclofenac is widely used as an anti-inflammatory compound worldwide and it is constantly being added as waste in the environment (Heberer 2002 J. Hydrol. 266 175-89), exceeding the permissible maximum concentration in the wastewater (GEO-3 2002 Programa de las Naciones Unidas para el Medio Ambiente; Golet et al 2003 Environ. Sci. Technol. 37 3243-9 Oviedo et al 2010 Environ. Toxicol. Pharmacol. 29 9-43 Le-Minh et al 2010 Water Res. 44 4295-323 Legrini et al 1993 Chem. Rev. 1093 671-98). The composite was synthesized by sol-gel technique with and without ultrasound irradiation (Singh and Nakate 2014 J. Nanopart. 2014 326747). The solids were deposited by ultrasound irradiation on active carbon fiber in order to optimize the diclofenac degradation. The solids were characterized by x-ray diffraction (XRD), nitrogen physisorption (BET), and scanning electron microscopy with EDS microanalysis (SEM-EDS). The crystal size was calculated with the Debye-Scherrer equation, and the band gap values by the diffuse reflectance method. The evaluation process was studied by UV-vis spectroscopy (Rizzoa et al 2009 Water Res. 43 979-88). It was found that in this synthesis method (ultrasound), textural properties such as porosity, specific surface area and morphology depend on the ultrasound irradiation. The proposed system, Fe3O4/titanium oxide hydrate showed better degradation profile than TiO2 anatase phase; the increase of diclofenac degradation was attributed to the textural properties of the composite, it avoids the filtering process since the separation can be achieved by magnetizing and/or decantation.

Continuous production of granular or powder Ti, Zr and Hf or their alloy products

DOEpatents

White, Jack C.; Oden, Laurance L.

1993-01-01

A continuous process for producing a granular metal selected from the group consisting of Ti, Zr or Hf under conditions that provide orderly growth of the metal free of halide inclusions comprising: a) dissolving a reducing metal selected from the group consisting of Na, Mg, Li or K in their respective halide salts to produce a reducing molten salt stream; b) preparing a second molten salt stream containing the halide salt of Ti, Zr or Hf; c) mixing and reacting the two molten streams of steps a) and b) in a continuous stirred tank reactor; d) wherein steps a) through c) are conducted at a temperature range of from about 800.degree. C. to about 1100.degree. C. so that a weight percent of equilibrium solubility of the reducing metal in its respective halide salt varies from about 1.6 weight percent at about 900.degree. C. to about 14.4 weight percent at about 1062.degree. C.; and wherein a range of concentration of the halide salt of Ti, Zn or Hf in molten halides of Na, Mg, Li or K is from about 1 to about 5 times the concentration of Na, Mg, Li or K; e) placing the reacted molten stream from step c) in a solid-liquid separator to recover an impure granular metal product by decantation, centrifugation, or filtration; and f) removing residual halide salt impurity by vacuum evaporator or inert gas sweep at temperatures from about 850.degree. C. to 1000.degree. C. or cooling the impure granular metal product to ambient temperature and water leaching off the residual metal halide salt.

The silent salesman: an observational study of personal tobacco pack display at outdoor café strips in Australia.

PubMed

Wakefield, Melanie A; Zacher, Meghan; Bayly, Megan; Brennan, Emily; Dono, Joanne; Miller, Caroline; Durkin, Sarah J; Scollo, Michelle M

2014-07-01

We sought to determine the relative frequency and nature of personal display of cigarette packs by smokers in two Australian cities where 30% front-of-pack and 90% back-of-pack health warnings have been used since 2006 and comprehensive tobacco marketing restrictions apply. An observational study counted patrons, active smokers and tobacco packs at cafés, restaurants and bars with outdoor seating. Pack orientation and use of cigarette cases were also noted. Overall, 18954 patrons, 1576 active smokers and 2153 packs were observed, meaning that one out of every 12.0 patrons was actively smoking, and one of every 8.8 patrons displayed a pack. Packs were more frequently observed in lower socio-economic neighbourhoods, reflecting the higher prevalence of smoking in those regions. Packs were displayed less often in venues where children were present, suggesting a greater tendency not to smoke around children. Most packs (81.4%) were oriented face-up, permitting prominent brand display. Only 1.5% of observed packs were cigarette cases, and 4.2% of packs were concealed by another item, such as a phone or wallet. Tobacco packs are frequently seen on table-tops in café strips, providing many opportunities for other patrons and passers-by to be incidentally exposed to cigarette brand names and imagery. Use of cigarette cases is rare, suggesting that smokers eventually habituate to pictorial warnings on branded packs and/or find repeated decanting of each newly purchased branded pack into a case to be inconvenient. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Biological treatment of produced water in a sequencing batch reactor by a consortium of isolated halophilic microorganisms.

PubMed

Pendashteh, A R; Fakhru'l-Razi, A; Chuah, T G; Radiah, A B Dayang; Madaeni, S S; Zurina, Z A

2010-10-01

Produced water or oilfield wastewater is the largest volume ofa waste stream associated with oil and gas production. The aim of this study was to investigate the biological pretreatment of synthetic and real produced water in a sequencing batch reactor (SBR) to remove hydrocarbon compounds. The SBR was inoculated with isolated tropical halophilic microorganisms capable of degrading crude oil. A total sequence of 24 h (60 min filling phase; 21 h aeration; 60 min settling and 60 min decant phase) was employed and studied. Synthetic produced water was treated with various organic loading rates (OLR) (0.9 kg COD m(-3) d(-1), 1.8 kg COD m(-3) d(-1) and 3.6 kg COD m(-3) d(-1)) and different total dissolved solids (TDS) concentration (35,000 mg L(-1), 100,000 mg L(-1), 150,000 mg L(-1), 200,000 mg L(-1) and 250,000 mg L(-1)). It was found that with an OLR of 0.9 kg COD m(-3) d(-1) and 1.8 kg COD m(-3) d(-1), average oil and grease (O&G) concentrations in the effluent were 7 mg L(-1) and 12 mg L(-1), respectively. At TDS concentration of 35,000 mg L(-1) and at an OLR of 1.8 kg COD m(-3)d(-1), COD and O&G removal efficiencies were more than 90%. However, with increase in salt content to 250,000 mg L(-1), COD and O&G removal efficiencies decreased to 74% and 63%, respectively. The results of biological treatment of real produced water showed that the removal rates of the main pollutants of wastewater, such as COD, TOC and O&G, were above 81%, 83%, and 85%, respectively.

Biomarkers and bioindicators of the environmental condition using a fish species (Pimelodus maculatus Lacepède, 1803) in a tropical reservoir in Southeastern Brazil.

PubMed

Araújo, F G; Morado, C N; Parente, T T E; Paumgartten, F J R; Gomes, I D

2018-05-01

The Funil Reservoir receives a large amount of xenobiotics from the Paraíba do Sul River (PSR) from large number of industries and municipalities in the watershed. This study aimed to assess environmental quality along the longitudinal profile of the Paraíba do Sul River-Funil Reservoir system, by using biomarkers and bioindicators in a selected fish species. The raised hypothesis is that Funil Reservoir acts as a filter for the xenobiotics of the PSR waters, improving river water quality downstream the dam. Two biomarkers, the ethoxyresorufin-O-deethylase activity (EROD), measured as fluorimetricly in S9 hepatic fraction, and the micronuclei frequency (MN), observed in erythrocytes of the cytoplasm, and three bioindicators, the hepatosomatic index (HSI), gonadosomatic index (GSI) and condition factor (CF) were used in Pimelodus maculatus, a fish species widely distributed in the system. Four zones were searched through a longitudinal gradient: 1, river upstream from the reservoir; 2, upper reservoir; 3, lower reservoir; 4, river downstream of the reservoir. EROD activity and HSI and GSI had significant differences among the zones (P<0.05). The upper reservoir had the lowest EROD activity and HSI, whereas the river downstream of the reservoir had the highest EROD and lowest GSI. The river upstream from the reservoir showed the highest HSI and GSI. It is suggested that the lowest environmental condition occur at the river downstream of the reservoir, where it seems to occur more influence of xenobiotics, which could be associated with hydroelectric plant operation. The hypothesis that Funil reservoir acts as a filter decanting pollution from the Paraíba do Sul River waters was rejected. These results are novel information on this subject for a native fish species and could be useful for future comparisons with other environments.

Mutagenicity and genotoxicity of drinking water in Guelma region, Algeria.

PubMed

Abda, Ahlem; Benouareth, Djamel E; Tabet, Mouna; Liman, Recep; Konuk, Muhsin; Khallef, Messaouda; Taher, Ali

2015-02-01

In this study, a battery of genotoxicity assays for monitoring drinking water was performed to assess the quality of the water resulting from the treatment plants. Five different types of samples were collected: raw water (P1), treated after pre-chlorination (P2), treated after decantation (P3), treated post-chlorination (P4), and consumers' taps (P5-P12). This study aims to evaluate the formation/occurrence of mutagenic and/or genotoxic compounds in surface drinking waters treated with chlorine disinfectant, during four seasonal experiments: summer, autumn, winter, and spring between 2012 and 2013 by bacterial reverse mutation assay in both Salmonella typhimurium TA98 and TA100 strains with or without metabolic activation system (S9 mix) and Allium cepa root meristematic cells, respectively. All of water samples, except at P1, P2, and P5 in summer; P1 in autumn; and P1 and P3-P12 in spring without S9 mix, and at P1 and P2 in summer and P6 and P8-P12 in spring with S9 mix, were found to be mutagenic in S. typhimurium TA98. However, only P11 and P12 in winter were found to be mutagenic for TA100 without S9 mix. The tested preparations in Allium anaphase-telophase test revealed a significant decrease in mitotic index (MI) and a simultaneous increase in chromosome aberrations (CAs) compared to the control. The bridge, stickiness, vagrant chromosomes, and disturbed chromosome aberrations were observed in anaphase-telophase cells. Physicochemical analysis, trihalomethanes (THMs), romoform (CHBr3), chloroform (CHCl3), bromodichloromethane (CHBrCl2), and dibromochloromethane (CHBr2Cl) levels in water samples were also determined. The results show also that this short-term battery tests are applicable in the routine monitoring of drinking water quality before and after distribution.

The flexural stiffness and tension state of basalt filter

NASA Astrophysics Data System (ADS)

Khalmuradovich, Sattarov Laziz; Ahmedovich, Kurbanov Abdirahim

2017-03-01

In recent years, there is a growing demand in Uzbekistan for new, cheap and competitive products from local raw materials, the demand being directly connected with the expansion and development opportunities of the mining, metallurgical and processing industries. In such conditions, the need for providing a solution of the problems faced by these industries is a very urgent one and requires further comprehensive studies. One of these tasks includes assessment of the force parameters and bending stiffness of basalt fibre filters, aimed at further improving the efficiency of local basalt raw materials and aiding in the manufacture of new, long-lasting, reliable and high-quality products. In this case, we studied the interaction of basalt fibre filter with a gas or liquid medium, the deformed state of the fibres under the action force of the gas or liquid, and the filter recovery process after removal of the load, all of which occur during mechanical filtration. These tasks are of interest because during the mechanical filtration of a gas or liquid (hereinafter, mechanical filtration) from solids, all attention is paid to the quality of the filtering process. The filtering quality, as known, is determined by the degree of contamination in the liquid undergoing treatment, duration of separation of the pulp into solid and liquid phases during the decantation process of the mixture and the amount of gas/ liquid released into the atmosphere along with carbon monoxide and toxic impurities. At the same time, the state and behaviour of the filtering material remain as minor factors, the consideration of which can play a decisive role in the establishment of filter life and work capacity. Solutions to these problems are very urgent and allow one to create new technologies for the production of basalt filters based on force parameters and bending stiffness, wherein the purification occurs without the intervention of chemicals.

Quantification of total dinutuximab concentrations in neuroblastoma patients with liquid chromatography tandem mass spectrometry.

PubMed

El Amrani, Mohsin; Szanto, Celina L; Hack, C Erik; Huitema, Alwin D R; Nierkens, Stefan; van Maarseveen, Erik M

2018-06-25

Neuroblastoma is one of the most commonly found solid tumors in children. The monoclonal antibody dinutuximab (DNX) targets the sialic acid-containing glycosphingolipid GD2 expressed on almost all neuroblastoma tumor cells and induces cell lysis. However, the expression of GD2 is not limited to tumor cells only, but is also present on central nerve tissue and peripheral nerve cells explaining dinutuximab toxicity. The most common adverse reactions are pain and discomfort, which may lead to discontinuation of the treatment. Furthermore, there is little to no data available on exposure and effect relationships of dinutuximab. We, therefore, developed an easy method in order to quantify dinutuximab levels in human plasma. Ammonium sulfate (AS) was used to precipitate all immunoglobulins (IgGs) in human plasma. After centrifugation, supernatant containing albumin was decanted and the precipitated IgG fraction was re-dissolved in a buffer containing 0.5% sodium dodecyl sulfate (SDS). Samples were then reduced, alkylated, and digested with trypsin. Finally, a signature peptide in complementarity determining region 1 of DNX heavy chain was quantified on LC-MS/MS using a stable isotopically labeled peptide as internal standard. AS purification efficiently removed 97.5% of the albumin fraction in the supernatant layer. The validation performed on DNX showed that within-run and between-run coefficients of variation (CV) for lower limit of quantification (LLOQ) were 5.5 and 1.4%, respectively. The overall CVs for quality control (QC) low, QC med, and QC high levels were < 5%. Linearity in the range 1-32 mg/L was excellent (r 2  > 0.999). Selectivity, stability, and matrix effect were in concordance with EMA guidelines. In conclusion, a method to quantify DNX in human plasma was successfully developed. In addition, the high and robust process efficiency enabled the utilization of a stable isotopically labeled (SIL) peptide instead of SIL DNX, which was commercially unavailable. Graphical abstract.

Detection of Giardia intestinalis infections in Polish soldiers deployed to Afghanistan.

PubMed

Korzeniewski, Krzysztof; Konior, Monika; Augustynowicz, Alina; Lass, Anna; Kowalska, Ewa

2016-01-01

Members of the Polish Military Contingent (PMC) have been stationed in Afghanistan since 2002. They typically serve in areas characterised by low standards of sanitation which often leads to the development of food- and waterborne diseases. The aim of the study was to evaluate the prevalence of Giardia intestinalis infections among Polish soldiers deployed to Afghanistan. The research study was conducted as part of a programme for prevention of parasitic diseases of the gastrointestinal tract run by the Polish Armed Forces. The study was carried out in August 2011; it involved 630 asymptomatic Polish soldiers serving in the Forward Operational Base (FOB) Ghazni in eastern Afghanistan. Stool specimens obtained from members of the PMC were first tested in FOB Ghazni (detection of Giardia intestinalis by Rida Quick Giardia immunochromatographic tests and Ridascreen Giardia immunoenzymatic tests - single samples). Next, the same biological material and two other faecal specimens fixed in 10% formalin were transported to the Military Institute of Medicine in Poland, where they were tested for Giardia intestinalis under light microscopy (direct smear, decantation in distilled water). Parasitological tests performed under light microscopy showed that 2.7% (17/630) of the study group were infected with Giardia intestinalis. Some of these results were confirmed by immunochromatographic tests (6/630). In contrast, immunoenzymatic tests (ELISA) demonstrated a significantly higher detection rate reaching 18.1% (114/630). Immunoenzymatic tests confirmed all the positive results given by light microscopy and by immunochromatographic tests. The prevalence rate of Giardia intestinalis infections in Polish soldiers deployed to Afghanistan was found to be high. Microscopic methods exhibit low sensitivity and therefore may result in the underestimation of the true parasite prevalence. Immunoenzymatic tests (ELISA) showing a much higher sensitivity in comparison to light microscopy and immunochromatographic tests ought to be applied in screening for intestinal protozoan infections in areas characterised by harsh environmental conditions.

Chitosan Coagulation to Improve Microbial and Turbidity Removal by Ceramic Water Filtration for Household Drinking Water Treatment.

PubMed

Abebe, Lydia S; Chen, Xinyu; Sobsey, Mark D

2016-02-27

The use of porous ceramic filters is promoted globally for household water treatment, but these filters are ineffective in removing viruses from water. In order to increase virus removal, we combine a promising natural coagulant, chitosan, as a pretreatment for ceramic water filters (CWFs) and evaluate the performance of this dual barrier water treatment system. Chitosan is a non-toxic and biodegradable organic polymer derived by simple chemical treatments from chitin, a major source of which is the leftover shells of crustacean seafoods, such as shrimp, prawns, crabs, and lobsters. To determine the effectiveness of chitosan, model test water was contaminated with Escherichia coli K011 and coliphage MS2 as a model enteric bacterium and virus, respectively. Kaolinite clay was used to model turbidity. Coagulation effectiveness of three types of modified chitosans was determine at various doses ranging from 5 to 30 mg/L, followed by flocculation and sedimentation. The pre-treated supernatant water was then decanted into the CWF for further treatment by filtration. There were appreciable microbial removals by chitosan HCl, acetate, and lactate pretreatment followed by CWF treatment, with mean reductions (95% CI) between 4.7 (± 1.56) and 7.5 (± 0.02) log10 for Escherichia coli, and between 2.8 (± 0.10) and 4.5 (± 1.04) log10 for MS2. Turbidity reduction with chitosan treatment and filtration consistently resulted in turbidities < 1 NTU, which meet turbidity standards of the US EPA and guidance by the World Health Organization (WHO). According to WHO health-based microbial removal targets for household water treatment technology, chitosan coagulation achieved health protective targets for both viruses and bacteria. Therefore, the results of this study support the use of chitosan to improve household drinking water filtration processes by increasing virus and bacteria reductions.

Simple and rapid purification of pediocin PA-1 from Pediococcus pentosaceous NCDC 273 suitable for industrial application.

PubMed

Vijay Simha, B; Sood, S K; Kumariya, Rashmi; Garsa, Anita Kumari

2012-10-12

The use of pediocins as food additives or drugs requires a simple and rapid method by which large quantities of homogeneous pediocin are produced at industrial level. Two centrifugation steps required during initial stages of purification i.e. separation of cells from fermentation broth and collection of precipitates after ammonium sulphate precipitation are the major bottlenecks for their large scale purification. In the present work, pediocin production by a new a dairy strain, Pediococcus pentosaceous NCDC 273 (identical to pediocin PA-1 at nucleotide sequence level), was found to be optimum at initial pH of 6.0 and 7.0 of basal MRS supplemented with 20 g/l of glucose or lactose at 20 and 24 h, respectively. Immobilization of cells through entrapment in alginate-xanthan gum gel beads with chitosan coating resulted in negligible cell release during fermentation. Thus, the cell free extract was directly collected through decantation, avoiding the need of centrifugation step at this stage. Subsequent ammonium sulphate precipitation at isoelectric point of pediocin PA-1 (8.85), using magnetic stirrer at high speed (approx. 1200 rpm), resulted in forceful deposition of precipitates on the wall of precipitation beaker allowing their collection using a spatula, avoiding centrifugation step at this stage also. Further purification using cation-exchange chromatography resulted in yield of 134.4% with more than 320 fold purification with the specific activity of 19×10⁵ AU/mg. The collection of single peak of pediocin at 41.9min in RP-HPLC, overlapping with standard pediocin PA-1, resulted in yield of 1.15 μg from 20 μl of sample applied. The overlapping of RP-HPLC peak and SDS-PAGE band corresponding to 4.6 kDa, confirmed the purity and identity of pediocin 273 as pediocin PA-1. Copyright © 2012 Elsevier GmbH. All rights reserved.

Effects of drying-wetting and freezing-thawing cycle on leachability of metallic elements in mine soils

NASA Astrophysics Data System (ADS)

Bang, H.; Kim, J.; Hyun, S.

2016-12-01

Mine leachate derived from contaminated mine sites with metallic elements can pose serious risks on human society and environment. Only labile fraction of metallic elements in mine soils is subject to leaching and movement by rainfall. Lability of metallic element in soil is a function of bond strengths between metal and soil surfaces, which is influenced by environmental condition (e.g., rainfall intensity, duration, temperature, etc.) The purpose of this study was to elucidate the effects of various climate conditions on the leaching patterns and lability of metallic elements in mine soils. To do this, two mine soils were sampled from two abandoned mine sites located in Korea. Leaching test were conducted using batch decant-refill method. Various climatic conditions were employed in leaching test such as (1) oven drying (40oC) - wetting cycles, (2) air drying (20oC) - wetting cycle, and (3) freezing (-40oC) - thawing cycles. Duration of drying and freezing were varied from 4 days to 2 weeks. Concentration of metallic elements, pH, Eh and concentration of dissolved iron and sulfate in leachate from each leaching process was measured. To identify the changes of labile fraction in mine soils after each of drying or freezing period, sequential extraction procedure (five fraction) was used to compare labile fraction (i.e., F1 + F2) of metallic elements. The concentration of metallic elements in mine leachate was increased after drying and freezing procedure. The amounts of released metallic element from mine soils was changed depending on their drying or freezing period. In addition, labile fraction of metallic elements in soil was also changed after drying and freezing. The changes in labile fraction after drying and freezing might be due to the increased soil surface area by pore water volume expansion. Further study is therefore needed to evaluate the impact of altered physical properties of soils such as hydration of soil surface area and shrinking by drying and freezing cycles.

Alginate microencapsulation technology for the percutaneous delivery of adipose-derived stem cells.

PubMed

Moyer, Hunter R; Kinney, Ramsey C; Singh, Kimberly A; Williams, Joseph K; Schwartz, Zvi; Boyan, Barbara D

2010-11-01

Autologous fat is the ideal soft-tissue filler; however, its widespread application is limited because of variable clinical results and poor survival. Engineered fillers have the potential to maximize survival. Alginate is a hydrogel copolymer that can be engineered into spheres of <200 μm, thus facilitating mass transfer, allowing for subcutaneous injection, and protecting cells from shearing forces. Alginate powder was dissolved in saline, and adipose-derived stem cells (ADSCs) were encapsulated (1 million cells/mL) in alginate using an electrostatic bead generator. To assess effects of injection on cell viability, microspheres containing ADSCs were separated into 2 groups: the control group was decanted into culture wells and the injection group was mixed with basal media and injected through a 21-gauge needle into culture wells. Microbeads were cultured for 3 weeks, and cell number and viability were measured weekly using electron and confocal microscopy. To assess effects of percutaneous injection in vivo, twenty-four male nude mice were randomly separated into 2 groups and injected with either empty microcapsules or ADSC-laden microcapsules. Mice were harvested at 1 and 3 months, and the implants were examined microscopically to assess bead and cell viability. A flow rate of 5 mL/h and an electrostatic potential of 7 kV produced viable ADSC-laden microbeads of <200 μm. There were no differences in bead morphology and ADSC viability between microcapsules placed versus injected into tissue culture plates for up to 3 weeks. Microspheres implanted in a nude mouse model show durability up to 3 months with a host response around each individual sphere. ADSCs remained viable and showed signs of mitosis. ADSCs can be readily cultured, encapsulated, and injected in alginate microspheres. Stem cells suspended in alginate microspheres survive in vivo and are seen to replicate in vitro.

Avian plasma chemistry analysis using diluted samples.

PubMed

Waldoch, Jennifer; Wack, Raymund; Christopher, Mary

2009-12-01

Clinical chemistry tests are essential for the diagnosis and monitoring of disease in birds. The small volume of blood that can be obtained from many avian species limits the use of routine in-house chemistry analyzers. The aim of this study was to examine the accuracy and precision of avian plasma chemistry values obtained by use of a benchtop analyzer in samples diluted with sterile water, as compared with undiluted samples. Whole blood samples were collected from 13 clinically healthy thick-billed parrots (Rhynchopsitta pachyrhyncha). The samples were placed in lithium heparin tubes and centrifuged and the plasma decanted. One aliquot was analyzed immediately using a VetScan benchtop analyzer with an avian-reptile-specific rotor that included 12 analytes. The remainder of the plasma was divided into two aliquots and stored at -80 degrees C until analysis. One of these aliquots was diluted 1:1, 1:1.5, 1:2, and 1:2.5 with sterile water to give final dilutions of 1:2, 1:2.5, 1:3, and 1:3.5, respectively. The other aliquot was pooled with the 12 other samples to create a plasma pool. The undiluted plasma pool and two final dilutions (1:2 and 1:3) of the pooled plasma were analyzed in replicate (n = 20) to determine intra- and interassay imprecision. Each dilution was analyzed using the avian-reptile rotor and the results multiplied by the appropriate dilution factor to obtain the final result. Significant differences were observed in clinical chemistry results obtained from diluted plasma samples for all analytes except aspartate aminotransferase, creatine kinase, and glucose. Uric acid concentration was not significantly different at dilutions of up to 1:3. Bile acids, globulins, and sodium concentrations were below the limit of detection in all diluted samples and were not statistically analyzed. Based on these results, dilution with sterile water is not recommended for biochemical analysis of avian plasma using the VetScan benchtop analyzer.

Thermo-chemical extraction of fuel oil from waste lubricating grease.

PubMed

Pilusa, Tsietsi Jefrey; Muzenda, Edison; Shukla, Mukul

2013-06-01

This study investigated the recovery of oil from waste grease through the process of thermal degradation in an aqueous solution of potassium hydroxide (KOH) followed by solvent extraction. Waste high temperature metal bearing grease was dissolved in a 15 w/w% KOH solution at 80°C while being agitated at 2000 rpm using a shear action agitator for a period of 15 min. Two distinct layers were observed after 8 min of settling time. The top layer being of dark brown oil and the bottom layer was a heterogeneous mixture. The two layers were separated by decantation. The bottom layer was cooled down to 45°C followed by slow addition of toluene (C7H8) while agitating at 1200 rpm for 15 min to prevent solids settling and minimise rapid volatilisation of the organic compounds in the mixture. Two distinct layers were also formed, the top homogeneous mixture of light brown oil-toluene mixture and the bottom sludge layer. The solvent was recovered from the oil for re-use by fractional distillation of the homogenous mixture. It was observed that 15 w/w% potassium hydroxide solution can chemically degrade the soap matrix in the grease and extract up to 49 w/w% of the fuel oil when subjected to high shear stress at a temperature of 80°C. The 26 w/w% extraction of oil in the remaining sludge was obtained by solvent extraction process with mass ratios of sludge to solvent of 2:1. Solvent recovery of 88% by mass was obtained via fractional distillation method. The combined extraction processes brought an overall oil yield of 75 w/w% from the waste grease. The fuel oil obtained from this process has similar properties to paraffin oil and can be blended with other oils as an alternative energy source. Copyright © 2013 Elsevier Ltd. All rights reserved.

Chitosan Coagulation to Improve Microbial and Turbidity Removal by Ceramic Water Filtration for Household Drinking Water Treatment

PubMed Central

Abebe, Lydia S.; Chen, Xinyu; Sobsey, Mark D.

2016-01-01

The use of porous ceramic filters is promoted globally for household water treatment, but these filters are ineffective in removing viruses from water. In order to increase virus removal, we combine a promising natural coagulant, chitosan, as a pretreatment for ceramic water filters (CWFs) and evaluate the performance of this dual barrier water treatment system. Chitosan is a non-toxic and biodegradable organic polymer derived by simple chemical treatments from chitin, a major source of which is the leftover shells of crustacean seafoods, such as shrimp, prawns, crabs, and lobsters. To determine the effectiveness of chitosan, model test water was contaminated with Escherichia coli K011 and coliphage MS2 as a model enteric bacterium and virus, respectively. Kaolinite clay was used to model turbidity. Coagulation effectiveness of three types of modified chitosans was determine at various doses ranging from 5 to 30 mg/L, followed by flocculation and sedimentation. The pre-treated supernatant water was then decanted into the CWF for further treatment by filtration. There were appreciable microbial removals by chitosan HCl, acetate, and lactate pretreatment followed by CWF treatment, with mean reductions (95% CI) between 4.7 (±1.56) and 7.5 (±0.02) log10 for Escherichia coli, and between 2.8 (±0.10) and 4.5 (±1.04) log10 for MS2. Turbidity reduction with chitosan treatment and filtration consistently resulted in turbidities < 1 NTU, which meet turbidity standards of the US EPA and guidance by the World Health Organization (WHO). According to WHO health-based microbial removal targets for household water treatment technology, chitosan coagulation achieved health protective targets for both viruses and bacteria. Therefore, the results of this study support the use of chitosan to improve household drinking water filtration processes by increasing virus and bacteria reductions. PMID:26927152

Enzymatic added extraction and clarification of fruit juices-A review.

PubMed

Sharma, Harsh P; Patel, Hiral; Sugandha

2017-04-13

Enzymatic treatment for juice extraction is most commonly used now a days. The enzymatic process is claimed to offer a number of advantages over mechanical-thermal comminution of several fruit pulps. Enzymes are an integral component of modern fruit juice manufacturing and are highly suitable for optimizing processes. Their main purposes are: increase extraction of juice from raw material, increase processing efficiency (pressing, solid settling or removal), and generate a final product that is clear and visually attractive. Juice extraction can be done by using various mechanical processes, which may be achieved through diffusion extraction, decanter centrifuge, screw type juice extractor, fruit pulper and by different types of presses. Enzymatic treatment prior to mechanical extraction significantly improves juice recovery compared to any other extraction process. Enzymatic hydrolysis of the cell walls increases the extraction yield, reducing sugars, soluble dry matter content and galacturonic acid content and titrable acidity of the products. Enzymatic degradation of the biomaterial depends upon the type of enzyme, incubation time, incubation temperature, enzyme concentration, agitation, pH and use of different enzyme combinations. We can conclude from the technical literature that use of the enzymes i.e. cellulases, pectinases, amylases and combination of these enzymes can give better juice yield with superior quality of the fruit juice. Pectinase enzyme can give maximum juice yield i.e. 92.4% at 360 minutes incubation time, 37°C incubation temperature and 5 mg/100 g of enzyme concentration. Whereas the combination of two enzymes i.e. pectin methyl esterase (PME) and polygalacturonase (PG) at 120 minutes of incubation time, 50°C of incubation temperature and 0.05 mg/100 gm of enzymatic concentration can give the maximum yield of 96.8% for plum fruits. This paper discusses the use of enzymes in fruit juice production focusing on the juice recovery, clarity and effect of the particular enzyme on the biochemical properties of the fruit juices.

The study of potable water treatment process in Algeria (boudouaou station) -by the application of life cycle assessment (LCA).

PubMed

Mohamed-Zine, Messaoud-Boureghda; Hamouche, Aksas; Krim, Louhab

2013-12-19

Environmental impact assessment will soon become a compulsory phase in future potable water production projects, in algeria, especially, when alternative treatment processes such sedimentation ,coagulation sand filtration and Desinfection are considered. An impact assessment tool is therefore developed for the environmental evaluation of potable water production. in our study The evaluation method used is the life cycle assessment (LCA) for the determination and evaluation of potential impact of a drink water station ,near algiers (SEAL-Boudouaoua).LCA requires both the identification and quantification of materials and energy used in all stages of the product's life, when the inventory information is acquired, it will then be interpreted into the form of potential impact " eco-indicators 99" towards study areas covered by LCA, using the simapro6 soft ware for water treatment process is necessary to discover the weaknesses in the water treatment process in order for it to be further improved ensuring quality life. The main source shown that for the studied water treatment process, the highest environmental burdens are coagulant preparation (30% for all impacts), mineral resource and ozone layer depletion the repartition of the impacts among the different processes varies in comparison with the other impacts. Mineral resources are mainly consumed during alumine sulfate solution preparation; Ozone layer depletion originates mostly from tetrachloromethane emissions during alumine sulfate production. It should also be noted that, despite the small doses needed, ozone and active Carbone treatment generate significant impacts with a contribution of 10% for most of the impacts.Moreover impacts of energy are used in producing pumps (20-25 GHC) for plant operation and the unitary processes (coagulation, sand filtration decantation) and the most important impacts are localized in the same equipment (40-75 GHC) and we can conclude that:- Pre-treatment, pumping and EDR (EDR: 0.-6 0 kg CO2 eq. /produced m3) are the process-units with higher environmental impacts.- Energy consumption is the main source of impacts on climate change.- Chemicals consumption (e.g. coagulants, oxidants) are the principle cause of impacts on the ozone layer depletion.- Conventional plants: pre-treatment has high GHG emissions due to chemicals consumption.

Use of an anaerobic sequencing batch reactor for parameter estimation in modelling of anaerobic digestion.

PubMed

Batstone, D J; Torrijos, M; Ruiz, C; Schmidt, J E

2004-01-01

The model structure in anaerobic digestion has been clarified following publication of the IWA Anaerobic Digestion Model No. 1 (ADM1). However, parameter values are not well known, and uncertainty and variability in the parameter values given is almost unknown. Additionally, platforms for identification of parameters, namely continuous-flow laboratory digesters, and batch tests suffer from disadvantages such as long run times, and difficulty in defining initial conditions, respectively. Anaerobic sequencing batch reactors (ASBRs) are sequenced into fill-react-settle-decant phases, and offer promising possibilities for estimation of parameters, as they are by nature, dynamic in behaviour, and allow repeatable behaviour to establish initial conditions, and evaluate parameters. In this study, we estimated parameters describing winery wastewater (most COD as ethanol) degradation using data from sequencing operation, and validated these parameters using unsequenced pulses of ethanol and acetate. The model used was the ADM1, with an extension for ethanol degradation. Parameter confidence spaces were found by non-linear, correlated analysis of the two main Monod parameters; maximum uptake rate (k(m)), and half saturation concentration (K(S)). These parameters could be estimated together using only the measured acetate concentration (20 points per cycle). From interpolating the single cycle acetate data to multiple cycles, we estimate that a practical "optimal" identifiability could be achieved after two cycles for the acetate parameters, and three cycles for the ethanol parameters. The parameters found performed well in the short term, and represented the pulses of acetate and ethanol (within 4 days of the winery-fed cycles) very well. The main discrepancy was poor prediction of pH dynamics, which could be due to an unidentified buffer with an overall influence the same as a weak base (possibly CaCO3). Based on this work, ASBR systems are effective for parameter estimation, especially for comparative wastewater characterisation. The main disadvantages are heavy computational requirements for multiple cycles, and difficulty in establishing the correct biomass concentration in the reactor, though the last is also a disadvantage for continuous fixed film reactors, and especially, batch tests.

Water: from the source to the treatment plan

NASA Astrophysics Data System (ADS)

Baude, I.; Marquet, V.

2012-04-01

Isabelle BAUDE isa.baude@free.fr Lycee français de Vienne Liechtensteinstrasse 37AVienna As a physics and chemistry teacher, I have worked on water from the source to the treatment plant with 27 pupils between 14 and 15 years old enrolled in the option "Science and laboratory". The objectives of this option are to interest students in science, to introduce them to practical methods of laboratory analyses, and let them use computer technology. Teaching takes place every two weeks and lasts 1.5 hours. The theme of water is a common project with the biology and geology teacher, Mrs. Virginie Marquet. Lesson 1: Introduction: The water in Vienna The pupils have to consider why the water is so important in Vienna (history, economy etc.) and where tap water comes from. Activities: Brainstorming about where and why we use water every day and why the water is different in Vienna. Lesson 2: Objectives of the session: What are the differences between mineral waters? Activities: Compare water from different origins (France: Evian, Vittel, Contrex. Austria: Vöslauer, Juvina, Gasteiner and tap water from Vienna) by tasting and finding the main ions they contain. Testing ions: Calcium, magnesium, sulphate, chloride, sodium, and potassium Lesson 3: Objectives of the session: Build a hydrometer Activities: Producing a range of calibration solutions, build and calibrate the hydrometer with different salt-water solutions. Measure the density of the Dead Sea's water and other mineral waters. Lesson 4: Objectives of the session: How does a fountain work? Activities: Construction of a fountain as Heron of Alexandria with simple equipment and try to understand the hydrostatic principles. Lesson 5: Objectives of the session: Study of the physical processes of water treatment (decantation, filtration, screening) Activities: Build a natural filter with sand, stone, carbon, and cotton wool. Retrieve the filtered water to test it during lesson 7. Lesson 6: Visit of the biggest treatment plant of Europe in Vienna. Lesson 7: Objectives of the session: Water Quality Monitoring: Biochemical Oxygen Demand (chemical analysis) in common with my colleague.

Pre-digestion to enhance volatile fatty acids (VFAs) concentration as a carbon source for denitrification in treatment of liquid swine manure.

PubMed

Wu, Sarah Xiao; Chen, Lide; Zhu, Jun; Walquist, McKenzie; Christian, David

2018-04-30

Insufficient denitrification in biological treatment is often a result of the lack of a carbon source. In this study, use of the volatile fatty acids (VFAs) generated via pre-digestion as a carbon source to improve denitrification in sequencing batch reactor (SBR) treatment of liquid swine manure was investigated. The pre-digestion of swine manure was realized by storing the manure in a sealed container in room temperature and samples were taken periodically from the container to determine the VFA levels. The results showed that after 14 days of pre-digestion, the VFA level in the digested liquid was increased by 200%. A polynomial relationship for the VFA level in the digested manure with the digestion time was observed with a correlation coefficient being 0.9748. Two identical SBRs were built and operated on 8-h cycles in parallel, with one fed with pre-digested and the other raw swine manure. There were five phases included in each cycle, i.e., anaerobic (90 min), anoxic (150 min), anoxic/anaerobic (90 min), anoxic/aerobic (120 min), and settle/decant (30 min), and the feeding was split to 600 mL/200 mL and performed at the beginning of and 240 min into the cycle. The SBR fed on pre-digested swine manure achieved successful denitrification with only 0.35 mg/L nitrate left in the effluent, compared to 15.9 mg/L found in the effluent of the other SBR. Nitrite was not detected in the effluent from both SBRs. The results also indicated that there was no negative impact of feeding SBRs with the pre-digested liquid swine manure for treatment on the removal of other constituents such as total solids (TS), volatile solids (VS), suspended solids (SS), volatile suspended solids (VSS), and soluble chemical oxygen demand (COD). Therefore, anaerobic digestion as a pretreatment can be an effective way to condition liquid swine manure for SBR treatment to achieve sufficient nitrate removal.

Arsenic in groundwaters of rural India: its geochemistry and mitigation approaches

NASA Astrophysics Data System (ADS)

Chatterjee, Debashis; Majumder, Santanu; Kundu, Amit; Barman, Sandipan; Chatterjee, Debankur; Bhattacharya, Prosun

2016-04-01

During the last few decades, arsenic (As) has been recognized as the most threatening contaminant in natural waters (especially groundwater). It has become a menace to the health of millions of people worldwide. Many large and small communities experience As contamination in groundwater and/or drinking water supplies in south-east Asia and the problem is grave in West Bengal and Bangladesh (Bengal Delta Plain, BDP) both in terms of human exposure as well as spatial coverage. It is frequently observed that As concentration in contaminated wells exceeds both WHO guideline value (10 mg/l) and stipulated National standard (50 mg/l) for both Bangladesh and India. Dissolved forms of As in the BDP water include arsenite (~50-70%), arsenate (~30-50%) and ultra-trace amount of monomethylarsonic acid and dimethylarsinic acid. Arsenite and arsenate species can interchange depending on redox potential (Eh), pH and biological processes. The prevailing local geomorphological features (surface water, sanitation, agricultural activity) can also influence the mobilization of As in addition to the dominant geological factors. Therefore, the local sedimentology and hydrogeology should also be given importance prior to implement or consider any policy to mitigate the As contamination of groundwater. Conventional treatment techniques to remove As from groundwater are costly and difficult to practice in rural areas of the BDP. There are several techniques available for groundwater As removal. Iron and Alum coagulation, softening [mediated by calcite or Mg(OH)2 formation], by reverse osmosis, using zero-valent iron and nanoparticulate zero-valent iron, several natural/synthetic metal oxides, naturally found minerals like siderite, hematite, using iron doped activated carbons, development of bio-physicochemical techniques, using granular TiO2 adsorbent are some of the many proposed removal techniques investigated by various researchers. Instead of using hazardous chemicals (e.g. chlorine, ozone in conventional method) As from groundwater can also be removed by exposure to sunlight (solar oxidation) in presence of dissolved iron (Fe) and a chelating agent (citrate, naturally available) followed by filtration with cloth or simple decantation. The technique is user friendly, low cost and easy to perform by the rural mass of the BDP.

Stratigraphic distribution, taphonomy and paleoenvironments of Spinicaudata in the Triassic and Jurassic of the Paraná Basin

NASA Astrophysics Data System (ADS)

Jenisch, Alan Gregory; Lehn, Ilana; Gallego, Oscar Florencio; Monferran, Mateo Daniel; Horodyski, Rodrigo Scalise; Faccini, Ubiratan Ferrucio

2017-12-01

Due to the chitino-phosphatic nature of Spinicaudata conchostracan exoskeletons, their carapaces exhibit a low preservational potential compared to other bivalve groups. However, the recent studies point towards the increased tolerance of the carapace against the physical processes. Due to this peculiar characteristic, conchostracan carapace have been utilized as precise temporal markers in estimating stratigraphic and taphonomic parameters. The same characteristic also makes the spinicaudatans useful in evaluating the depositional processes and environments. The present work aims at providing a paleoenvironmental and stratigraphic analysis of conchostracans (Spinicaudata) from the Triassic-Jurassic of the Paraná Basin (Santa Maria and Caturrita formations) in terms of the sedimentary facies analysis, depositional system characterization, and analysis of the taphonomic signatures of the fossiliferous horizons within these formations. The results from the taphonomic study delineates the presence of 4 distinct fossil assemblages based on the causative mechanism and fundamental characteristics of the fossil concentrations: two taphonomic assemblages in the laminated mudstone beds deposited from the decanting fine-grained sediments in floodplains; the sandstone beds with plane parallel laminations and dune- and ripple-cross-stratifications deposited from the flooding-related overflow in the floodplains; and the association of laminated mudstone and massive sandstone beds deposited as the river mouth bars. The results show that the taphonomic signatures, e.g., closed valves, may indicate the various patterns of autochthony and allochthony. In the fine-grained floodplain assemblages, the high degree of preservation can be attributed to autochthony in the conchostracans, whereas the preservational condition of floodplain sandstone sheet and mouth bar assemblages point toward parautochthony and even allochthony. Therefore, the preservational quality of conchostracan exoskeletons is likely a function of parameters, e.g., the transport duration, the distance from life position, and the magnitude of events causing their final burial. Within the observed species, the recognition of Eustheria minuta in the stratigraphic level of the Passo das Tropas creek corroborates an age for these deposits between the late Middle Triassic and early Upper Triassic. The presence of a new form, likely related to the family Fushunograptidae in sediments from the Caturrita Formation, suggests a Jurassic age for these deposits.

Service Learning Course in Which Undergraduates and Middle School Students Investigate Levels of Pathogen Indicating Bacteria in Beach Sand

NASA Astrophysics Data System (ADS)

Imamura, G.; Mika, K.; Lin, T.; Lee, C.; Lin, C.; Jay, J.

2007-12-01

Service-learning is a pedagogy that combines academic rigor with activities that address human and community needs. Over the past three years, we have developed a service-learning course that involves UCLA students working with 6th graders in an economically disadvantaged neighborhood to address issues of environmental science and health. This past year UCLA students conducted a research project in collaboration with a middle school class to investigate levels of pathogen-indicating organisms in beach sand near the Santa Monica pier. All students were taught necessary methods in class by the UCLA professor, and then met at the field site. Fieldwork involved collection of water and sand samples from various locations, extraction of bacteria from sand by shaking with buffer and decanting, and addition of sample to growth media that allow quantification of two organisms, Escherichia coli and enterococci. These organisms are typically used to indicate fecal contamination of water. Methods were straightforward and were accomplished by the 6th graders with only modest supervision by the UCLA students. Results showed extremely high levels of pathogen indicating organisms in the vicinity of a diverted stormdrain, indicating a continuing problem with the diversion. Levels decreased with distance away from the stormdrain, indicating migration of the organisms from the site of the diversion. UCLA students then visited the sixth grade classroom to help the sixth graders create Powerpoint posters including statement of hypotheses, graphs of the results, pictures of the entire process, and conclusions. Middle school students then visited UCLA to tour the campus and present their posters at a poster session hosted by the Center for Embedded Networked Sensing at UCLA. Desired outcomes at the 6th grade level included: 1) increased interest in science; 2) greater knowledge of and interest in attending college; and 3) enhanced knowledge of and feeling of political empowerment concerning environmental health issues. Outcomes for the UCLA students included: 1) gains in learning through the action of teaching; 2) awareness of education justice issues in Los Angeles; and 3) enhanced feeling of personal commitment to community and political advocacy work.

Activities of Combined Sewer Overflows: A Comparison of Measured and Computed Data

NASA Astrophysics Data System (ADS)

Ostrowski, M. W.; Koch, J.; Wetzstein, A.

In order to relieve sewerage systems of excess stormwaters during heavy rainfalls overflow structures are necessary for a safe operation of urban drainage and wastew- ater treatment facilities. Overflow tanks have storage effects while pure overflows di- vide the discharges and route the excess water in the next watercourse. The outflows from combined sewage overflows can evoke significant effects on the receiving waters. Hydraulic effects ("hydraulic stress") result from the additional discharges, which are generally introduced at a single point. Toxic effects are caused by the pollutant load of the decanted discharges. In awareness of these effects an immission based consid- eration is required. The lack of reliable, measurement based data is obvious, although the generally accepted necessity of those is noted in recent research projects and regu- lations of public authorities. An immission based view necessitates data regarding the amount, number and duration of the overflows. Particularly with regard to the storm overflows this data is mostly achieved by means of computational simulations. The lack of measured data is the consequence of the adverse conditions in sewer pipes and the complex hydraulic situation at the overflow structures. Reliable data is necessary for the verification, the validation and the improvement of hydrological models. Within the scope of a research project, carried out in the section for Hydrology and Water Management of the Technical University of Darmstadt, a storm overflow was equipped with measuring devices. Aims of the investigations were to discover the limiting boundary conditions in measuring sewer discharges and to record reliable data, concerning the overflow activities of the observed structure. The measured data should be compared with the results of the model SMUSI, which is an evaluation model of the public authorities in the federal state of Hesse, Germany. It is the objective of the presentation to - specify the implementation and the perfor- mance of the measurement site - describe the processing and evaluation of the mea- suring data - compare the measured data with the computed data based on SMUSI simulations - discuss the opportunities and boundaries of measuring in urban hydro- logical systems regarding new approaches (measuring, modelling, managing) as well as the attainable accurracies of measurement.

Predominant Leptospiral Serogroups Circulating among Humans, Livestock and Wildlife in Katavi-Rukwa Ecosystem, Tanzania

PubMed Central

Assenga, Justine A.; Matemba, Lucas E.; Muller, Shabani K.; Mhamphi, Ginethon G.; Kazwala, Rudovick R.

2015-01-01

Background Leptospirosis is a worldwide zoonotic disease and a serious, under-reported public health problem, particularly in rural areas of Tanzania. In the Katavi-Rukwa ecosystem, humans, livestock and wildlife live in close proximity, which exposes them to the risk of a number of zoonotic infectious diseases, including leptospirosis. Methodology/Principal Findings A cross-sectional epidemiological study was carried out in the Katavi region, South-west Tanzania, to determine the seroprevalence of Leptospira spp in humans, domestic ruminants and wildlife. Blood samples were collected from humans (n = 267), cattle (n = 1,103), goats (n = 248), buffaloes (n = 38), zebra (n = 2), lions (n = 2), rodents (n = 207) and shrews (n = 11). Decanted sera were tested using the Microscopic Agglutination Test (MAT) for antibodies against six live serogroups belonging to the Leptospira spp, with a cutoff point of ≥ 1:160. The prevalence of leptospiral antibodies was 29.96% in humans, 30.37% in cattle, 8.47% in goats, 28.95% in buffaloes, 20.29% in rodents and 9.09% in shrews. Additionally, one of the two samples in lions was seropositive. A significant difference in the prevalence P<0.05 was observed between cattle and goats. No significant difference in prevalence was observed with respect to age and sex in humans or any of the sampled animal species. The most prevalent serogroups with antibodies of Leptospira spp were Sejroe, Hebdomadis, Grippotyphosa, Icterohaemorrhagie and Australis, which were detected in humans, cattle, goats and buffaloes; Sejroe and Grippotyphosa, which were detected in a lion; Australis, Icterohaemorrhagie and Grippotyphosa, which were detected in rodents; and Australis, which was detected in shrews. Antibodies to serogroup Ballum were detected only in humans. Conclusions The results of this study demonstrate that leptospiral antibodies are widely prevalent in humans, livestock and wildlife from the Katavi-Rukwa ecosystem. The disease poses a serious economic and public health threat in the study area. This epidemiological study provides information on circulating serogroups, which will be essential in designing intervention measures to reduce the risk of disease transmission. PMID:25806825

DOE Office of Scientific and Technical Information (OSTI.GOV)

Addy, Susan Amrose

Arsenic in drinking water is a major public health problem threatening the lives of over 140 million people worldwide. In Bangladesh alone, up to 57 million people drink arsenic-laden water from shallow wells. ElectroChemical Arsenic Remediation(ECAR) overcomes many of the obstacles that plague current technologies and can be used affordably and on a small-scale, allowing for rapid dissemination into Bangladesh to address this arsenic crisis. In this work, ECAR was shown to effectively reduce 550 - 580 μg=L arsenic (including both As[III]and As[V]in a 1:1 ratio) to below the WHO recommended maximum limit of 10 μg=L in synthetic Bangladesh groundwatermore » containing relevant concentrations of competitive ions such as phosphate, silicate, and bicarbonate. Arsenic removal capacity was found to be approximately constant within certain ranges of current density, but was found to change substantially between ranges. In order of decreasing arsenic removal capacity, the pattern was: 0.02 mA=cm 2> 0.07 mA=cm 2> 0.30 - 1.1 mA=cm 2> 5.0 - 100 mA=cm 2. Current processing time was found to effect arsenic removal capacity independent of either charge density or current density. Electrode polarization studies showed no passivation of the electrode in the tested range (up to current density 10 mA=cm 2) and ruled out oxygen evolution as the cause of decreasing removal capacity with current density. Simple settling and decantation required approximately 3 days to achieve arsenic removal comparable to filtration with a 0.1 mu m membrane. X-ray Absorption Spectroscopy (XAS) showed that (1) there is no significant difference in the arsenic removal mechanism of ECAR during operation at different current densities and (2) the arsenic removal mechanism in ECAR is consistent with arsenate adsorption onto a homogenous Fe(III)oxyhydroxide similar in structure to 2-line ferrihydrite. ECAR effectively reduced high arsenic concentrations (100 - 500 mu g=L) in real Bangladesh tube well water collected from three regions to below the WHO limit of 10 mu g=L. Prototype fabrication and field testing are currently underway.« less

The study of potable water treatment process in Algeria (boudouaou station) -by the application of life cycle assessment (LCA)

PubMed Central

2013-01-01

Environmental impact assessment will soon become a compulsory phase in future potable water production projects, in algeria, especially, when alternative treatment processes such sedimentation ,coagulation sand filtration and Desinfection are considered. An impact assessment tool is therefore developed for the environmental evaluation of potable water production. in our study The evaluation method used is the life cycle assessment (LCA) for the determination and evaluation of potential impact of a drink water station ,near algiers (SEAL-Boudouaoua). LCA requires both the identification and quantification of materials and energy used in all stages of the product’s life, when the inventory information is acquired, it will then be interpreted into the form of potential impact “ eco-indicators 99” towards study areas covered by LCA, using the simapro6 soft ware for water treatment process is necessary to discover the weaknesses in the water treatment process in order for it to be further improved ensuring quality life. The main source shown that for the studied water treatment process, the highest environmental burdens are coagulant preparation (30% for all impacts), mineral resource and ozone layer depletion the repartition of the impacts among the different processes varies in comparison with the other impacts. Mineral resources are mainly consumed during alumine sulfate solution preparation; Ozone layer depletion originates mostly from tetrachloromethane emissions during alumine sulfate production. It should also be noted that, despite the small doses needed, ozone and active Carbone treatment generate significant impacts with a contribution of 10% for most of the impacts. Moreover impacts of energy are used in producing pumps (20-25 GHC) for plant operation and the unitary processes (coagulation, sand filtration decantation) and the most important impacts are localized in the same equipment (40-75 GHC) and we can conclude that: – Pre-treatment, pumping and EDR (EDR: 0.-6 0 kg CO2 eq. /produced m3) are the process-units with higher environmental impacts. – Energy consumption is the main source of impacts on climate change. – Chemicals consumption (e.g. coagulants, oxidants) are the principle cause of impacts on the ozone layer depletion. – Conventional plants: pre-treatment has high GHG emissions due to chemicals consumption. PMID:24355378

Separation of Single-Walled Carbon Nanotubes with DEP-FFF

NASA Technical Reports Server (NTRS)

Schmidt, Howard K.; Peng, Haiqing; Alvarez, Noe; Mendes, Manuel; Pasquali, Matteo

2011-01-01

A process using a modified dielectrophoresis device separates single-walled carbon nanotubes (SWNTs) according to their polarizability in electric fields. This depends on the size and dielectric constant of individual nanotubes and easily separates metallic from semiconducting nanotubes. Separation by length has also been demonstrated. Partial separation (enrichment) according to bandgap (which is linked to polarizability) has also been shown and can be improved to full separation of individual types of semiconducting SWNTs with better control over operational parameters and the length of SWNT starting material. This process and device can be scaled affordably to generate useful amounts of semiconducting SWNTs for electronic device development and production. In this study, a flow injection dielectrophoresis technique was used with a modified dielectrophoresis device. The length, width, and height of the modified chamber were 28, 2.5, and 0.025 cm, respectively. On the bottom of the chamber, there are two arrays of 50-m-wide, 2-m-thick gold electrodes, which are connected to an AC voltage generator and are alternately arranged so that every electrode is adjacent to two electrodes of the opposite polar. There is an additional plate electrode on the top of the chamber that is negatively biased. During the experiment, a syringe pump constantly pumps in the mobile phase, 1-percent sodium dodecylbenzene sulfonate (SDBS) solution, into the chamber. The frequency and voltage are set to 1 MHz and 10 V peak-to-peak, respectively. About 150 micro-L of SWNTs in 1- percent SDBS decanted solution are injected to the mobile phase through a septum near the entrance of the chamber. The flow rate of the mobile phase is set to 0.02 cu cm/min. The injected SWNTs sample flows through the chamber before it is lead into a fluorescence flow-through cell and collected for further analysis. The flow-through cell has three windows, thus allowing the fluorometer to collect fluorescence spectrum and visible absorption spectrums simultaneously. Dielectrophoresis field-flow fractionation (DEP-FFF) generally depends on interaction of a sedimentation force and DEP force for particle separation, and SWNTs are neutrally buoyant in water. In this innovation, the third electrode was added to create a sedimentation force based on DC electrophoresis. This makes this particular device applicable to separations on any neutrally buoyant particles in solution and a more general process for a broad range of nanomaterials sorting and separations.

Glass ionomer cements functionalised with a concentrated paste of chlorhexidine hexametaphosphate provides dose-dependent chlorhexidine release over at least 14 months.

PubMed

Bellis, Candice A; Nobbs, Angela H; O'Sullivan, Dominic J; Holder, James A; Barbour, Michele E

2016-02-01

The aim of this study was to create prototype glass ionomer cements (GICs) incorporating a concentrated paste of chlorhexidine-hexametaphosphate (CHX-HMP), and to investigate the long-term release of soluble chlorhexidine and the mechanical properties of the cements. The purpose is the design of a glass ionomer with sustained anticaries efficacy. CHX-HMP paste was prepared by mixing equimolar solutions of chlorhexidine digluconate and sodium hexametaphosphate, adjusting ionic strength, decanting and centrifuging. CHX-HMP paste was incorporated into a commercial GIC in substitution for glass powder at 0.00, 0.17, 0.34, 0.85 and 1.70% by mass CHX-HMP. Soluble chlorhexidine release into artificial saliva was observed over 436 days using absorbance at 255nm. Diametral tensile and compressive strength were measured after 7 days' setting (37°C, 100% humidity) and tensile strength after 436 days' aging in artificial saliva. 0.34% CHX-HMP GICs were tested for their ability to inhibit growth of Streptococcus mutans in vitro. GICs supplemented with CHX-HMP exhibited a sustained dose-dependent release of soluble chlorhexidine. Diametral tensile strength of new specimens was unaffected up to and including 0.85% CHX-HMP, and individual values of tensile strength were unaffected by aging, but the proportion of CHX-HMP required to adversely affect tensile strength was lower after aging, at 0.34%. Compressive strength was adversely affected by CHX-HMP at substitutions of 0.85% CHX-HMP and above. Supplementing a GIC with CHX-HMP paste resulted in a cement which released soluble chlorhexidine for over 14 months in a dose dependent manner. 0.17% and 0.34% CHX-HMP did not adversely affect strength at baseline, and 0.17% CHX-HMP did not affect strength after aging. 0.34% CHX-HMP GICs inhibited growth of S. mutans at a mean distance of 2.34mm from the specimen, whereas control (0%) GICs did not inhibit bacterial growth. Although GICs release fluoride in vivo, there is inconclusive evidence regarding any clinical anticaries effect. In this study, GICs supplemented with a paste of chlorhexidine-hexametaphosphate (CHX-HMP) exhibited a sustained release of chlorhexidine over at least 14 months, and small additions of CHX-HMP did not adversely affect strength. Copyright © 2016 Elsevier Ltd. All rights reserved.

Removal of organic micropollutants in an artificial recharge system

NASA Astrophysics Data System (ADS)

Valhondo, C.; Nödler, K.; Köck-Schulmeyer, M.; Hernandez, M.; Licha, T.; Ayora, C.; Carrera, J.

2012-04-01

Emerging contaminants including pharmaceutically active compounds (PhACs), personal care products (PCPs) and pesticides are increasingly being identified in the environment. Emerging pollutants and their transformation products show low concentration in the environment (ng/L), but the effects of the mixtures and lifelong exposure to humans are currently unknown. Many of these contaminants are removed under aerobic conditions in water treatment plants. However, several pharmaceuticals and metabolites present in wastewater are not eliminated by conventional treatment processes. Several lab studies, however, show that the behaviour of many of these micropollutants is affected by the dominant redox conditions. However, data from field experiments are limited and sometimes contradictory. Artificial recharge is a widespread technology to increase the groundwater resources. In this study we propose a design to enhance the natural remediation potential of the aquifer with the installation of a reactive layer at the bottom of the infiltration pond. This layer is a mixture of compost, aquifer material, clay and iron oxide. This layer is intended to provide an extra amount of DOC to the recharge water and to promote biodegradation by means of the development of different redox zones along the travel path through the unsaturated zone and within the aquifer. Moreover, compost, clay and iron oxide of the layer are assumed to increase sorption surfaces for neutral, cationic and anionic compounds, respectively. The infiltration system is sited in Sant Vicenç dels Horts (Barcelona, Spain). It consists of a decantation pond, receiving raw water from the Llobregat River (highly affected from treatment plant effluents), and an infiltration pond (5600 m2). The infiltration rate is around 1 m3/m2/day. The system is equipped with a network of piezometers, suction cups and tensiometers. Infiltration periods have been performed before and after the installation of the reactive layer. Water from the Infiltration pond, the unsaturated zone and groundwater have been sampled and analyzed in order to elucidate the effect of the reactive layer. First results of micropollutants under natural conditions show significant removal rates of atenolol and Ibuprofen as well as the recalcitrant behaviour of carbamazepine. Once the layer was installed, carbamazepine concentration in groundwater samples was lower than the concentration in the infiltration water. These preliminary results are promising but, however, they need to be confirmed by further analysis, which will be conducted during the next weeks.

Morphology and sediment dynamics of the Capbreton canyon (Bay of Biscay, SW France)

NASA Astrophysics Data System (ADS)

Gaudin, M.; Umr 5805; Ifremer Team

2003-04-01

The Canyon of Capbreton extending in the Bay of Biscay (SW France) is the deepest canyon in the world. Its structure and morphology was studied using new multibeam bathymetry, acoustic imagery and high-resolution seismic data. The canyon head appears only 250 m away from the coast line and runs westward parallel to the north coast of Spain for 160 km due to structural control, then turns northward, widens and abruptly disappears in the continental rise by 3500 m water depth. Its northern margin is flat and progrades clearly westward. Conversely the southern margin is steep and progrades towards the north (i.e. towards the canyon). Down to 800 m water depth, the canyon deeply incises the continental shelf and the axial channel is meandering (sinuosity of 1.9). The canyon shows both major and minor stream beds, perched tributary valleys, nested terraces and abandoned meanders. The terraces have three morphologies: (1) flat, (2) with a raised side or (3) with a horseshoe structure. These morphologies have been interpreted as overbank deposits or nested levees (1 and 2) or as the result of meander abandon (3). Terraces of types (1) and (2) contain mainly fine deposits resulting from decantation of the top of turbulent surges that flow in the canyon. Westward (800 to 2000 m water depth) the main talweg remains sinuous (1.7). On the southern margin, several straight or slightly sinuous S-N tributary valleys are followed by alignments of pockmarks that also indicate a structural control. On the northern margin, a single large tributary valley with a sinuous central talweg, flowing from the upper Aquitaine continental slope, is interpreted as a giant slump scar due to sediment instability. This valley is bordered to the west by a topographic high with sediment waves on the external flank that might be interpreted as a sedimentary levee. The canyon recorded a recent turbidite activity. An 18 cm-thick turbidite was deposited at 650 m water depth by a turbidity current triggered by the storm which affected the French Atlantic coast on 27.12.1999. These present sedimentary processes contribute to maintain the freshness of the canyon morphology. However, the present frequency (in the range of one event every ten years) of gravity processes is too low to explain the incision. This suggests an increased activity when the canyon head was connected to the Adour River (previous to 1310 AD).

Tracking natural and anthropogenic origins of dissolved arsenic during surface and groundwater interaction in a post-closure mining context: Isotopic constraints.

PubMed

Khaska, Mahmoud; Le Gal La Salle, Corinne; Verdoux, Patrick; Boutin, René

2015-01-01

Arsenic contamination of stream waters and groundwater is a real issue in Au-As mine environments. At the Salsigne Au-As mine, southern France, arsenic contamination persists after closure and remediation of the site. In this study, natural and anthropogenic arsenic inputs in surface water and groundwater are identified based on (87)Sr/(86)Sr, and δ(18)O and δ(2)H isotopic composition of water. In the wet season, downstream of the remediated zone, the arsenic contents in stream water and alluvial aquifer groundwater are high, with values in the order of 36 μg/L and 40 μg/L respectively, while upstream natural background average concentrations are around 4 μg/L. Locally down-gradient of the reclaimed area, arsenic concentrations in stream water showed 2 peaks, one during an important rainy event (101 mm) in the wet season in May, and a longer one over the dry period, reaching 120 and 110 μg/L respectively. The temporal variations in arsenic content in stream water can be explained i) during the dry season, by release of arsenic stored in the alluvial sediments through increased contribution from base flow and decreased stream flow and ii) during major rainy events, by mobilization of arsenic associated with important surface runoff. The (87)Sr/(86)Sr ratios associated with increasing arsenic content in stream waters downstream of the reclaimed area are significantly lower than that of the natural Sr inherited from Variscan formations. These low (87)Sr/(86)Sr ratios are likely to be associated with the decontaminating water treatment processes, used in the past and still at present, where CaO, produced from marine limestone and therefore showing a low (87)Sr/(86)Sr ratios, is used to precipitate Ca3(AsO4)2. The low Sr isotope signatures will then impact on the Sr isotope ratio of (1) the Ca-arsenate stored in tailing dams, (2) effluent currently produced by water treatment process and (3) groundwater draining from the overall site. Furthermore, Δ(2)H shows that the low (87)Sr/(86)Sr ratio, arsenic rich water is characterized by an evaporated signature suggesting a potential influence of water impacted by evaporation during storage in decantation lagoons. This study shows the suitability of Sr and stable isotopes of water as tracers to differentiate natural and anthropogenic sources of arsenic release or other trace elements from mining context where CaO is used for water treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

Tracking natural and anthropogenic origins of dissolved arsenic during surface and groundwater interaction in a post-closure mining context: Isotopic constraints

NASA Astrophysics Data System (ADS)

Khaska, Mahmoud; Le Gal La Salle, Corinne; Verdoux, Patrick; Boutin, René

2015-06-01

Arsenic contamination of stream waters and groundwater is a real issue in Au-As mine environments. At the Salsigne Au-As mine, southern France, arsenic contamination persists after closure and remediation of the site. In this study, natural and anthropogenic arsenic inputs in surface water and groundwater are identified based on 87Sr/86Sr, and δ18O and δ2H isotopic composition of water. In the wet season, downstream of the remediated zone, the arsenic contents in stream water and alluvial aquifer groundwater are high, with values in the order of 36 μg/L and 40 μg/L respectively, while upstream natural background average concentrations are around 4 μg/L. Locally down-gradient of the reclaimed area, arsenic concentrations in stream water showed 2 peaks, one during an important rainy event (101 mm) in the wet season in May, and a longer one over the dry period, reaching 120 and 110 μg/L respectively. The temporal variations in arsenic content in stream water can be explained i) during the dry season, by release of arsenic stored in the alluvial sediments through increased contribution from base flow and decreased stream flow and ii) during major rainy events, by mobilization of arsenic associated with important surface runoff. The 87Sr/86Sr ratios associated with increasing arsenic content in stream waters downstream of the reclaimed area are significantly lower than that of the natural Sr inherited from Variscan formations. These low 87Sr/86Sr ratios are likely to be associated with the decontaminating water treatment processes, used in the past and still at present, where CaO, produced from marine limestone and therefore showing a low 87Sr/86Sr ratios, is used to precipitate Ca3(AsO4)2. The low Sr isotope signatures will then impact on the Sr isotope ratio of (1) the Ca-arsenate stored in tailing dams, (2) effluent currently produced by water treatment process and (3) groundwater draining from the overall site. Furthermore, Δ2H shows that the low 87Sr/86Sr ratio, arsenic rich water is characterized by an evaporated signature suggesting a potential influence of water impacted by evaporation during storage in decantation lagoons. This study shows the suitability of Sr and stable isotopes of water as tracers to differentiate natural and anthropogenic sources of arsenic release or other trace elements from mining context where CaO is used for water treatment.

BICAPA case study of natural hazards that trigger technological disasters

NASA Astrophysics Data System (ADS)

Boca, Gabriela; Ozunu, Alexandru; Nicolae Vlad, Serban

2010-05-01

Industrial facilities are vulnerable to natural disasters. Natural disasters and technological accidents are not always singular or isolated events. The example in this paper show that they can occur in complex combinations and/or in rapid succession, known as NaTech disasters, thereby triggering multiple impacts. This analysis indicates that NaTech disasters have the potential to trigger hazmat releases and other types of technological accidents. Climate changes play an important role in prevalence and NATECH triggering mechanisms. Projections under the IPCC IS92 a scenario (similar to SRES A1B; IPCC, 1992) and two GCMs indicate that the risk of floods increases in central and eastern Europe. Increase in intense short-duration precipitation is likely to lead to increased risk of flash floods. (Lehner et al., 2006). It is emergent to develop tools for the assessment of risks due to NATECH events in the industrial processes, in a framework starting with the characterization of frequency and severity of natural disasters and continuing with complex analysis of industrial processes, to risk assessment and residual functionality analysis. The Ponds with dangerous technological residues are the most vulnerable targets of natural hazards. Technological accidents such as those in Baia Mare, (from January to March 2000) had an important international echo. Extreme weather phenomena, like those in the winter of 2000 in Baia Mare, and other natural disasters such as floods or earthquakes, can cause a similar disaster at Târnăveni in Transylvania Depression. During 1972 - 1978 three decanting ponds were built on the Chemical Platform Târnăveni, now SC BICAPA SA, for disposal of the hazardous-wastes resulting from the manufacture of sodium dichromate, inorganic salts, sludge from waste water purification and filtration, wet gas production from carbide. The ponds are located on the right bank of the river Târnava at about 35-50m from the flooding defense dam. The total amount of toxic waste stored in the three ponds is about 2500 tons, equivalent at 128 tons expressed in hexavalent chromium. The ponds contour dikes are strongly damaged in many places, their safety is jeopardized by leakages, sliding slopes and ravens. The upstream dike has an increased failure risk. The upstream dike has an increased failure risk. In that section the coefficients of safety are under the allowable limit, both in static applications, and the earthquake. The risk of failure is very high also due to the dikes slopes. The risk becomes higher in case of heavy rainfall, floods or an earthquake.

Metal-organic cooperative catalysis in C-H and C-C bond activation and its concurrent recovery.

PubMed

Park, Young Jun; Park, Jung-Woo; Jun, Chul-Ho

2008-02-01

The development of an efficient catalytic activation (cleavage) system for C-H and C-C bonds is an important challenge in organic synthesis, because these bonds comprise a variety of organic molecules such as natural products, petroleum oils, and polymers on the earth. Among many elegant approaches utilizing transition metals to activate C-H and C-C bonds facilely, chelation-assisted protocols based on the coordinating ability of an organic moiety have attracted great attention, though they have often suffered from the need for an intact coordinating group in a substrate. In this Account, we describe our entire efforts to activate C-H or C-C bonds adjacent to carbonyl groups by employing a new concept of metal-organic cooperative catalysis (MOCC), which enables the temporal installation of a 2-aminopyridyl group into common aldehydes or ketones in a catalytic way. Consequently, a series of new catalytic reactions such as alcohol hydroacylation, oxo-ester synthesis, C-C triple bond cleavage, hydrative dimerization of alkynes, and skeletal rearrangements of cyclic ketones was realized through MOCC. In particular, in the quest for an optimized MOCC system composed of a Wilkinson's catalyst (Ph 3P) 3RhCl and an organic catalyst (2-amino-3-picoline), surprising efficiency enhancements could be achieved when benzoic acid and aniline were introduced as promoters for the aldimine formation process. Furthermore, a notable accomplishment of C-C bond activation has been made using 2-amino-3-picoline as a temporary chelating auxiliary in the reactions of unstrained ketones with various terminal olefins and Wilkinson's catalyst. In the case of seven-membered cyclic ketones, an interesting ring contraction to five- or six-membered ones takes place through skeletal rearrangements initiated by the C-C bond activation of MOCC. On the other hand, the fundamental advances of these catalytic systems into recyclable processes could be achieved by immobilizing both metal and organic components using a hydrogen-bonded self-assembled system as a catalyst support. This catalyst-recovery system provides a homogeneous phase at high temperature during the reaction and a heterogeneous phase at room temperature after the reaction. The product could be separated conveniently from the self-assembly support system by decanting the upper layer. The immobilized catalysts of both 2-aminopyridine and rhodium metal species sustained high catalytic activity for up to the eight catalytic reactions. In conclusion, the successful incorporation of an organocatalytic cycle into a transition metal catalyzed reaction led us to find MOCC for C-H and C-C bond activation. In addition, the hydrogen-bonded self-assembled support has been developed for an efficient and effective recovery system of homogeneous catalysts and could be successful in immobilizing both metal and organic catalysts.

A review on anthropogenic impact to the Micro Prespa lake and its damages

NASA Astrophysics Data System (ADS)

Frasheri, N.; Pano, N.; Frasheri, A.; Beqiraj, G.; Bushati, S.; Taska, E.

2012-04-01

Paper presents the results of the integrated and multidisciplinary studies for investigation of the anthropogenic damages to Albanian part of the transborder Micro Prespa Lake. Remote sensing with Landsat images was used for identification of environmental changes in time for the period 1970 - 2010. Micro Prespa Lake is lake with international status, as Ramsar Convection, International Park and Special Protection Area-79/409/EEC. According to the studies, investigations and analyses, the following were concluded: Devolli River- Micro Prespa Lake irrigation system was not scientifically supported by environmental engineering, hydroeconomy and International Rights principles. It does work according to the projected parameters, and also, doesn't supply the agricultural needs. About of 10 % of the water volume, discharges by Devolli River in Micro Prespa Lake during the winter, is taken from this lake for the irrigation in summer. Great surface of Albanian part of Micro Prespa Lake is destroyed. The other part of the lake is atrophied and the habitat and biodiversity are damaged. Important and unique species of fish, birds and plants of national and international values are risked. The underground karstic connection ways for water circulation are blocked. There are ruining the historic values of the area, such the encient Treni cave from the Bronze Age. The Albanian part of the Micro Prespa Lake has been damaged by the human activities. A huge amount of 1,2 million cubic meters alluvium has been deposited on the lake bottom and lakeshore, which was transported by the Devolli River waters, since 1974. This river waters, rich in alluvium and organic coal material from outcropped geological formations, also absorbed free chemical toxic remains by the drainage of Devolli farm ground, which have changed the chemical features of the lake water and degrading it. Micro Prespa Lake communicates with Macro Prespa Lake, and together with Ohrid Lake. Blockage of underground karstic connection ways has diminished not only the components of the lake water balance, but also the decreasing yield of the underground springs, that supply the Ohrid lake and drinkable water springs. The Albanian part of the Micro Prespa Lake plays the role of a gigantic decanter. This is an unprecedented case, not only in Albanian but also in Balkan and World hydrography. Devolli river alluvium deposited in Micro Prespa Lake caused the otherwise of territory of Republic of Albania in this area. Albania will not have any part in this lake after some years. The social and public opinion in Albania, must be conscious for the otherwise of Albanian territory, which in the case of Micro Prespa Lake has a national and international negative effect on destructions of a transborder lake, defendey by Europian Convents.

A review of agricultural pesticide incidents in man in England and Wales, 1952-71

PubMed Central

Hearn, C. E. D.

1973-01-01

Hearn, C. E. D. (1973).British Journal of Industrial Medicine,30, 253-258. A review of agricultural pesticide incidents in man in England and Wales, 1952-71. An analysis was carried out of the poisoning incidents attributed to pesticides in England and Wales investigated by the Safety Inspectorate of the Pesticides Branch of the Ministry of Agriculture, Fisheries, and Food from 1952 to 1971. All poisoning incidents attributed to pesticides which are reported to the Safety Inspectorate are recorded and separated into reported and confirmed incidents. The confirmed incidents are classified into fatal and non-fatal. The non-fatal incidents are subdivided into four categories, systemic poisoning, eye injuries, dermatitis, and chemical burns. There were nine fatal cases of poisoning due to pesticides between 1952 and 1971, of which only three were occupational in origin. The remaining six were non-occupational but were investigated by the Safety Inspectorate only because the incident happened to arise on, or in connection with, a farm. The details of all the cases are recorded. There were 222 non-fatal confirmed incidents during the period, affecting a total of 296 persons. There has been an increased frequency of incidents since 1966 largely attributable to more complete and comprehensive recording by the Safety Inspectorate. Out of a total of 250 recorded pesticide effects, 121 (48·5%) were systemic poisoning, 57 (22·8%) were eye injuries, 54 (21·6%) were dermatitis, and 18 (7·1%) were chemical burns. Of the 121 incidents of non-fatal systemic poisoning, usually of a mild character, 34 were due to organophosphates, 26 to a single incident involving chloropicrin, 15 to arsenites, eight to dinitro compounds, three to nicotine, two to fungicides, one to cyanide, and one to an organomercury compound. Thirty-one incidents were not classified because the symptoms were non-specific in character and the worker had been exposed to a large number of different chemicals. In some instances the relationship of the symptoms to previous exposure to pesticides was extremely uncertain. Eye injuries and dermatitis were attributable to a wide variety of different chemicals and in the majority of instances were mild. Sulphuric acid, used for potato haulm destruction, was the commonest recorded cause of chemical burns. The main problems in the use of pesticides in England and Wales today are (1) the illicit decanting of concentrate from the manufacturer's labelled containers, (2) the hoarding of incompletely used containers, (3) the disposal of empty containers, and (4) the importation of pesticides in inadequately labelled containers. These defined practical problems of safety in application and accident control are perhaps of greater importance than the long-term theoretical toxicological effects of pesticides which may be attracting too much attention today. PMID:4737427

Iodine Standard Materials: Preparation and Inter-Laboratory Comparisons

DOE Office of Scientific and Technical Information (OSTI.GOV)

D D Jenson; M L Adamic; J E Olson

The Idaho National Laboratory is preparing to enter the community of AMS practioners who analyze for 129Iodine. We expect to take delivery of a 0.5 MV compact accelerator mass spectrometry system, built by NEC, in the early summer of 2014. The primary mission for this instrument is iodine; it is designed to analyze iodine in the +3 charge state. As part of the acceptance testing for this instrument, both at NEC and on-site in our laboratory, some sort of standard or reference material is needed to verify performance. Appropriate standard materials are not readily available in the commercial marketplace. Smallmore » quantities can sometimes be acquired from other laboratories already engaged in iodine analyses. In the longer-term, meaningful quantities of standard materials are needed for routine use in analyses, and for quality control functions1. We have prepared some standard materials, starting with elemental Woodward iodine and NIST SRM 3231 [Iodine-129 Isotopic Standard (high level)] 10-6 solution. The goal was to make mixtures at the 5x10-10, 5x10-11, 5x10-12 ratio levels, along with some unmodified Woodward, in the chemical form of silver iodide. Approximately twenty grams of each of these mixtures were prepared. The elemental Woodward iodine was dissolved in chloroform, then reduced to iodide using sodium bisulfite in water. At this point the NIST spike material was added, in the form of sodium iodide. The mixed iodides were oxidized back to iodine in chloroform using hydrogen peroxide. This oxidation step was essential for isotopic equilibration of the 127 and 129 atoms. The iodine was reduced to iodide using sodium bisulfite as before. Excess sulfites and sulfates were precipitated with barium nitrate. After decanting, silver nitrate was used to precipitate the desired silver iodide. Once the silver iodide was produced, the material was kept in darkness as much as possible to minimize photo-oxidation. The various mixtures were synthesized independently of each other; there were no serial dilutions involved. Aliquots of these four materials have been submitted to five established AMS laboratories where iodine analyses are routinely performed: ETH (Zurich), CNA (Seville), PRIME (Purdue), LLNL (California), and Isotrace (Toronto.) Results from four of these laboratories have been received; in general they indicate that the desired 129/127 ratios have been achieved. We will discuss the results of this informal round-robin exercise. If the installation of the instrument in Idaho goes well, we may have some very preliminary results from the new system. An integral part of data reporting is the approach to data reduction. Accordingly, there will also be some discussion of various philosophies of data handling in regard to the use of standards to adjust data, and background subtraction.« less

Pedo-sedimentary record of human-environment interaction in ditches and waterlogged depressions on tableland (roman and early medieval period) : micromorphological cases studies from Marne-la-Vallée area (Paris Basin, France)

NASA Astrophysics Data System (ADS)

Cammas, C.; Blanchard, J.; Broutin, P.; Berga, A.

2012-04-01

On lœss derived soils located on the Stampien plateau from the Paris Basin (France), archaeological anthroposols and ancient cultivated soils are only preserved in very few places. Recent archaeological excavations showed the presence of a pattern of roman ditches and waterlogged depressions (« mares ») under the actual cultivated horizon (Ap). This presence strongly suggests extensive past agricultural practices and water management. An original system of ditches was found Near Marne-la-Vallée (France). It is composed of two parts, one being large ditches characterized by flat bottom and sometimes water layered deposits, called « fossés collecteurs » by the archaeologists, and the orher being smaller ditches with colluvial deposits. Our objectives was to use archaeological and micromorphological studies in order to study i) the agricultural function of these ditches and depressions, ii) their evolution with time. Observations conducted on the infilling of a « fossé collecteur » at Bussy-Saint-Georges suggest that it was not part of a drainage system, but that it was a linear water controlled system, with a ramp in one part, and a basin or a tank in another, and that it was used for others anthropic activities. In the same area, a large waterlogged depression was studied, and micromorphological analysis helped to elucidate its pedo-sedimentary formation processes. At the bottom, massive silty clayey matrix retained water. Thin layers composed of silt and clay (indicating low energy flows and decantation), sometimes impregnated and hardened by iron, alternated with silty deposit (indicating higher ernergy water layered deposits). The thin, non porous and iron impregnated crusts helped to raise the depression level, as well as, most likely the water table during roman period, maintaining waterlogging conditions. At the beginning of the early medival period, a slightly peaty event was discriminated. Higher in the profile, in more redoxic conditions, ferruginous infilling of the microporosity and some vertic pedo-features alternated with higher energy deposits (fine sands). Some other important results are to be considered. The sedimentary matrix characteristics succession, a more calcareaous and lœss like sediments for the roman period and the beginning of the early medieval period, and a decarbonated matrix with clay, probably coming from the erosion of a luvisol, at the end of early medieval period. As a conclusion these elements show that two differents areas of the plateau were successively exploited. Furthermore, in all the profile, sedimentary and pedological features indicate successive water flows of variable intensity, wich could have been influenced by meteorological / climatical events, but our results suggest that they were more likely to have been controlled mainly by human activities, in connection with soils and ditch system management, especially during the early medieval period.

SCIX IMPACT ON DWPF CPC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, D.

2011-07-14

A program was conducted to systematically evaluate potential impacts of the proposed Small Column Ion Exchange (SCIX) process on the Defense Waste Processing Facility (DWPF) Chemical Processing Cell (CPC). The program involved a series of interrelated tasks. Past studies of the impact of crystalline silicotitanate (CST) and monosodium titanate (MST) on DWPF were reviewed. Paper studies and material balance calculations were used to establish reasonable bounding levels of CST and MST in sludge. Following the paper studies, Sludge Batch 10 (SB10) simulant was modified to have both bounding and intermediate levels of MST and ground CST. The SCIX flow sheetmore » includes grinding of the CST which is larger than DWPF frit when not ground. Nominal ground CST was not yet available, therefore a similar CST ground previously in Savannah River National Laboratory (SRNL) was used. It was believed that this CST was over ground and that it would bound the impact of nominal CST on sludge slurry properties. Lab-scale simulations of the DWPF CPC were conducted using SB10 simulants with no, intermediate, and bounding levels of CST and MST. Tests included both the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles. Simulations were performed at high and low acid stoichiometry. A demonstration of the extended CPC flowsheet was made that included streams from the site interim salt processing operations. A simulation using irradiated CST and MST was also completed. An extensive set of rheological measurements was made to search for potential adverse consequences of CST and MST and slurry rheology in the CPC. The SCIX CPC impact program was conducted in parallel with a program to evaluate the impact of SCIX on the final DWPF glass waste form and on the DWPF melter throughput. The studies must be considered together when evaluating the full impact of SCIX on DWPF. Due to the fact that the alternant flowsheet for DWPF has not been selected, this study did not consider the impact of proposed future alternative DWPF CPC flowsheets. The impact of the SCIX streams on DWPF processing using the selected flowsheet need to be considered as part of the technical baseline studies for coupled processing with the selected flowsheet. In addition, the downstream impact of aluminum dissolution on waste containing CST and MST has not yet been evaluated. The current baseline would not subject CST to the aluminum dissolution process and technical concerns with performing the dissolution with CST have been expressed. Should this option become feasible, the downstream impact should be considered. The main area of concern for DWPF from aluminum dissolution is an impact on rheology. The SCIX project is planning for SRNL to complete MST, CST, and sludge rheology testing to evaluate any expected changes. The impact of ground CST transport and flush water on the DWPF CPC feed tank (and potential need for decanting) has not been defined or studied.« less

First Report of the Carolina Spiral Nematode, Scutellonema brachyurus, from Soil of a Garden in Crete, Greece.

PubMed

Tzortzakakis, Emmanuel A; Cantalapiedra-Navarrete, Carolina; Archidona-Yuste, Antonio; Palomares-Rius, Juan E; Castillo, Pablo

2016-03-01

Members of the genus Scutellonema can cause substantial crop losses to ornamental and cultivated plants directly by feeding ectoparasitically on plant roots (Bridge et al., 2005; Coyne et al., 2006). In May 2015, a soil sample from a house garden from Heraklion city in Crete, Greece, was sent for diagnosis of plant-parasitic nematodes. In this place, there had been cactus (Opuntia sp.) plants (probably imported), which were uprooted 3 to 4 years earlier. After that, the area was cropped with cucumber (Cucumis sativus L.) in spring-summer and leaf vegetables such as spinach (Spinacia oleracea L.) and chicory (Cichorium intybus L.) in autumn-winter. The soil was collected 1 mon after the end of chicory crop. A population density (ca. 30 individuals/100 cm(3) of soil) of spiral nematodes (Scutellonema sp.) was found by extracting soil with the wet sieving and decanting method (Cobb, 1918). Morphological and molecular analyses of females identified the species as Scutellonema brachyurus (Steiner, 1938) Andrássy, 1958. The morphology of females was characterized by a hemispherical lip region with four to six annuli, morphometric data for 12 females were L, 640 to 760 μm; a, 24.6 to 30.6; b, 5.8 to 7.4; c, 69.1 to 99.3; c´ 0.5 to 0.6; stylet, 24.5 to 27.5 μm with anterior part shorter than posterior; and spermatheca nonfunctional and male absent. The morphology agreed with the description of S. brachyurus (van den Berg et al., 2013). Alignment indicated that the D2-D3 and ITS sequences (KU059494 and KU059495, respectively) showed 99% and 100% to 99% similarity, respectively, to other sequences of S. brachyurus (type A) deposited in GenBank from the United States, Italy, and Korea (JX472037-JX472046, DQ328753, FJ485643; and JX472069, JX472070, JX472071, respectively), differing from one to six nucleotides. Phylogenetic analyses using Bayesian inference of these sequences placed the Scutellonema sp. in a highly supported (100%) clade that included all S. brachyurus (type A) sequences deposited in GenBank (van den Berg et al., 2013). All identification methods were consistent with S. brachyurus. To our knowledge, this is the first report of S. brachyurus for Greece. As the cucumbers and the leaf vegetables cultivated in the area were seed planted, we consider that the nematode originated most probably from the cactus plants which had been previously root ball planted. Scutellonema brachyurus may represent a threat for ornamental and cultivated plants production in Crete, Greece. The nematode has been already reported, mainly in greenhouses of six European countries (CABI and EPPO, 2006). In most of these cases, it is hypothesized that the nematode was introduced by imported plant material.

Water - an inexhaustible resource?

NASA Astrophysics Data System (ADS)

Le Divenah, C.; Esperou, E.

2012-04-01

We have chosen to present the topic "Water", by illustrating problems that will give better opportunities for interdisciplinary work between Natural Science (Physics, Chemistry, Biology and Geology) teachers at first, but also English teachers and maybe others. Water is considered in general, in all its shapes and states. The question is not only about drinking water, but we would like to demonstrate that water can both be a fragile and short-lived resource in some ways, and an unlimited energy resource in others. Water exists on Earth in three states. It participates in a large number of chemical and physical processes (dissolution, dilution, biogeochemical cycles, repartition of heat in the oceans and the atmosphere, etc.), helping to maintain the homeostasis of the entire planet. It is linked to living beings, for which water is the major compound. The living beings essentially organized themselves into or around water, and this fact is also valid for human kind (energy, drinking, trade…). Water can also be a destroying agent for living beings (tsunamis, mud flows, collapse of electrical dams, pollution...) and for the solid earth (erosion, dissolution, fusion). I) Water, an essential resource for the human kind After having highlighted the disparities and geopolitical problems, the pupils will study the chemistry of water with its components and their origins (isotopes, water trip). Then the ways to make it drinkable will be presented (filtration, decantation, iceberg carrying…) II) From the origin of water... We could manage an activity where different groups put several hypotheses to the test, with the goal to understand the origin(s?) of water on Earth. Example: Isotopic signature of water showing its extraterrestrial origin.. Once done, we'll try to determine the origin of drinking water, as a fossil resource. Another use of isotopes will allow them to evaluate the drinking water age, to realize how precious it can be. III) Water as a sustainable energy resource Water is used to produce energy under different processes like ancient tamed energy such as water mills, locks or more recently tidal energy, marine current power, generators based on swell or osmotic gradients. The pupils will work in groups to present different techniques to the class. We could try to determine if all these energy resources could replace the actual major energy source in France: nuclear. Conclusion: Liquid water is probably the cradle of life. Since the birth of human kind, its history is closely linked to the presence of water: drinking, fishing, hygiene, and also transport or business is strictly depending on this resource. Described as a fragile and limited resource when it is used for human consumption, we realize that water is also an uneven resource of energy for the next generations. The challenge will then be to reconcile these different aspects: respecting this nourishing resource and preserving it from pollution, overexploitation or wasting, and at the same time, using water as energy for a world that has a growing population.

SLUDGE WASHING AND DEMONSTRATION OF THE DWPF FLOWSHEET IN THE SRNL SHIELDED CELLS FOR SLUDGE BATCH 7A QUALIFICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.; Billings, A.; Click, D.

2011-07-08

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry (Sludge Batch 7a*) be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are oftenmore » added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). Sludge Batch 7a (SB7a) is composed of portions of Tanks 4, 7, and 12; the Sludge Batch 6 heel in Tank 51; and a plutonium stream from H Canyon. SRNL received the Tank 51 qualification sample (sample ID HTF-51-10-125) following sludge additions to Tank 51. This report documents: (1) The washing (addition of water to dilute the sludge supernate) and concentration (decanting of supernate) of the SB7a - Tank 51 qualification sample to adjust sodium content and weight percent insoluble solids to Tank Farm projections. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the washed Tank 51 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a non-radioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the initial slurry samples and samples after each phase of CPC processing. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7a related data together in a single permanent record and to discuss the overall aspects of SB7a processing.« less

Prevalence of intestinal parasitic infections in the population of Central Asia on the example of inhabitants of Eastern Afghanistan

PubMed

Korzeniewski, Krzysztof

Parasitic diseases of the gastrointestinal tract are a major health problem worldwide, especially in the Third World countries, where poor standards of hygiene and sanitation as well as the lack of medical care facilitate the spread of food and waterborne infections. To estimate the prevalence of intestinal parasitic infections in Central Asia on the example of the population inhabiting the Ghazni Province in eastern part of the country and to assess the validity of the WHO recommended mass deworming campaign carried out in Afghanistan. Taking into consideration the fact that hundreds of thousands of immigrants from Asia and Africa have recently been flooding into Europe, it has become necessary to investigate the epidemiology of intestinal parasitoses in areas characterized by different climatic conditions and poor standards of sanitation. The study was conducted in eastern Afghanistan between November 2011 and April 2014. Parasitological examination was performed on 3 different study groups: 110 soldiers from the Afghan National Army (adults), 1,167 patients hospitalized at the Ghazni Provincial Hospital (807 children and adolescents aged 1–18 and 360 adults), and 1,869 students (7–18 years) frequenting local schools. The study involved 3,146 people including: 2,248 females and 898 males; 2,676 children and adolescents (1–18 years) and 460 adults (19–85 years). Three stool samples were collected from each study subject at the intervals of 2 to 3 days. The samples were fixed in 10% formalin and then transported by air to the Department of Epidemiology and Tropical Medicine (Military Institute of Medicine) in Poland, where they were examined by light microscopy using 3 different diagnostic methods (direct smear in Lugol’s solution, decantation with distilled water, Fülleborn’s flotation). In total, 1,220 Afghans were found to be infected with pathogenic intestinal parasites (38.8%): 44/110 soldiers (40.0%), 322/807 hospitalized children and adolescents (39.9%), 102/360 hospitalized adults (28.3%) and 752/1869 children and adolescents frequenting local schools (40.2%). Higher infection rates were observed in children and adolescents (40.1% vs. 31.1% adults), in boys (40.8% vs. 39.9% girls), and in the adult population – in women (31.2% vs. 31.0% men). The most commonly detected intestinal parasites in all study groups were: Ascaris lumbricoides (619/3146, 19.7%), Giardia intestinalis (489/3146, 15.5%) and Hymenolepis nana (206/3146, 6.5%). The prevalence and diversity of intestinal parasitic infections is high in the population of Central Asia. The infections caused by a wide range of nematodes, cestodes and protozoa are common among inhabitants of eastern Afghanistan. This fact suggests that the WHO-recommended deworming strategy (a single dose of 500 mg mebendazole or 400 mg albendazole) needs to be reviewed and should be replaced by targeted antiparasitic chemotherapy (albendazole, metronidazole, praziquantel), following mass screening of the local population.

Monitoring induced denitrification in an artificial aquifer recharge system.

NASA Astrophysics Data System (ADS)

Grau-Martinez, Alba; Torrentó, Clara; Folch, Albert; Domènech, Cristina; Otero, Neus; Soler, Albert

2014-05-01

As demands on groundwater increase, artificial recharge is becoming a common method for enhancing groundwater supply. The Llobregat River is a strategic water supply resource to the Barcelona metropolitan area (Catalonia, NE Spain). Aquifer overexploitation has leaded to both a decrease of groundwater level and seawater intrusion, with the consequent deterioration of water quality. In the middle section of the aquifer, in Sant Vicenç del Horts, decantation and infiltration ponds recharged by water from the Llobregat River (highly affected from wastewater treatment plant effluents), were installed in 2007, in the framework of the ENSAT Life+ project. At the bottom of the infiltration pond, a vegetal compost layer was installed to promote the growth of bacteria, to induce denitrification and to create favourable conditions for contaminant biodegradation. This layer consists on a mixture of compost, aquifer material, clay and iron oxide. Understanding the fate of contaminants, such as nitrate, during artificial aquifer recharge is required to evaluate the impact of artificial recharge in groundwater quality. In order to distinguish the source of nitrate and to evaluate the capability of the organic reactive layer to induce denitrification, a multi-isotopic approach coupled with hydrogeochemical data was performed. Groundwater samples, as well as river samples, were sampled during artificial and natural recharge periods. The isotopic analysis included: δ15N and δ18O of dissolved nitrate, δ34S and δ18O of dissolved sulphate, δ13C of dissolved inorganic carbon, and δ2H and δ18O of water. Dissolved nitrate isotopic composition (δ15NNO3 from +9 to +21 o and δ18ONO3 from +3 to +16 ) demonstrated that heterotrophic denitrification induced by the reactive layer was taking place during the artificial recharge periods. An approximation to the extent of nitrate attenuation was calculated, showing a range between 95 and 99% or between 35 and 45%, by using the extreme literature ɛN values of -4o and -22o respectively (Aravena and Robertson, 1998; Pauwels et al., 2000). Ongoing denitrification batch experiments will allow us to determine the specific nitrogen and oxygen isotopic fractionation induced by the organic reactive layer, in order to estimate more precisely the extent of denitrification during artificial aquifer recharge. These results confirmed that the reactive layer induces denitrification in the recharge ponds area, proving the usefulness of an isotopic approach to characterize water quality improvement occurring during artificial aquifer recharge. References 1. Aravena, R., Robertson, W.D., 1998. Use of multiple isotope tracers to evaluate denitrification in ground water: Study of nitrate from a large-flux septic system plume. Ground Water, 36(6): 975-982. 2. Pauwels, H., J.C., Kloppmann, W., 2000. Denitrification and mixing in a schist aquifer: Influence on water chemistry and isotopes. Chemical Geology, 168(3-4): 307-324. Acknowledgment This study was supported by the projects CGL2011-29975-C04-01 from the Spanish Government, 2009SGR-00103 from the Catalan Government and ENPI/2011/280-008 from the European Commission. Please fill in your abstract text.

An Evaluation of Partial Digestion Protocols for the Extraction and Measurement of Trace Metals of Environmental Concern in Marine and Estuarine Sediments

NASA Astrophysics Data System (ADS)

Winters, S. J.; Krahforst, C.; Sherman, L.; Kehm, K.

2013-12-01

As part of a broad study of the fate and transport of trace metals in estuarine sediments (Krahforst et al., 2013), the efficacy of commonly-used partial digestion protocols, including ISO 11466 (treatment with aqua regia), EPA 3050B (nitric acid followed by H2O2) and a modified rock digestion method ('RD' method- H2O2 followed by nitric), were evaluated for two NIST SRM materials, marine sediment 2702 and estuarine sediment 1646a. Unlike so-called total sediment digestions, the methods studied in this work do not employ hydrofluoric acid and are thought to leave silicates substantially or wholly intact. These methods can in principle compliment studies based on total digestions by providing information about trace metals in phases that are potentially more labile in the marine environment. Samples were digested in ~150 mg aliquots. Application of ISO 11466 and EPA 3050B followed published protocols except that digestions were carried out in trace-metal clean 15 mL capped Teflon vessels in an Al block digester and, at the end of the procedure, the supernatant was decanted from undigested material following repeated centrifugation in 2% nitric acid. Digested solutions were analyzed for Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Ag, Cd, Sn and Pb content by ICPMS. All elements were analyzed in collision reaction cell mode to minimize isobaric interferences, except Cd and Ag, which were analyzed in standard mode. Instrument performance was monitored in-run by analyzing the SRM 1643e and several quality-check standards. Two repeated digestions of SRM 2702 and SRM 1646a using EPA 3050B produced identical yields, within the standard deviation of repeated analyses (0 - 5%), for all analyzed elements except Cu, which varied by 30% for SRM 2702. The same was true for ISO 11466, although the standard deviation of repeated analyses for this digestion series tended to be larger (< ~15%). The RD method, which consists of pre-treatment with H2O2 followed by repeated treatments with nitric acid, produced the highest average yields for all elements, ranging from 50% of the Al in SRM 2702 up to ~100% for Cd and Pb. The higher recoveries for the RD method may indicate that pre-treatment with H2O2 more effectively removes organics compared with the conventional methods. Yields for ISO 11466 digestions typically range from 5 - 15% higher than EPA 3050B for all studied elements. Comparisons between the two sediments demonstrated that the acid-extractable fraction differs for several elements. For example results from all three digestion methods confirm a ~40% difference in yield for Mn between SRM 2702 and SRM 1646a. Overall, the results indicate that yields for trace element analyses of marine and estuarine sediments resulting from partial digestion are sensitive to the digestion technique, and in particular the methods employed for removal of organic phases. This work was supported by NSF Grant EAR-0922733 and a Maryland Sea Grant Program Development Award.

Measuring turbidity, and indicator to evaluate drinkability of waters in Southern countries? Approaches from Burkina Faso, Sudan and Argentina case studies

NASA Astrophysics Data System (ADS)

Lavie, Emilie; Robert, Elodie

2013-04-01

The relationship between proportion of suspended solids, dissolved oxygen and bacteriology has long been proven (Brock, 1966; Lechevallier et al., 1985; Bustina and Levallois, 2003; Chang and Liao, 2012), bacteria need coarse elements to hang on and develop. However, water bacteriology analyses are difficult to implement in southern countries. They are expensive and require sterile equipment, transport in cold conditions and a nearby laboratory, which remains difficult in remote areas under these hot latitudes. Yet, simple measurement devices allow to know in a few minutes the water turbidity. Is turbidity an efficient tool to evaluate the drinkability of water when no bacteriological analyses are possible? The results proposed here are taken from three different studies whose purposes were to measure different physical, chemical and bacteriological parameters of water used for human and/or animal consumption. One of the finalities was to propose a method, at lower cost, to evaluate the drinkability of water for consumption. Four case studies were chosen: the basin of the Doubegue River in Burkina Faso is a rural area of a developing country, where drinking water is taken from the alluvial aquifer close to the surface. Furthermore, the laundry is washed and the children play in running streams. Major expansion of the cultivated lands since 1980s has brought important soils losses, thus a chronicle contamination of surface water with suspended solids (Robert, 2012). The Mendoza and Tunuyán Rivers Basins in Argentina, an emerging country, have snow-glaciar regimes with naturally turbid waters. They supply drinking water to two towns, Mendoza and Tunuyán cities, respectively 1 million and 40,000 inhabitants. However, these two streams -whose watersheds are common- do not present the same managements: the Mendoza River has been equipped with large hydraulic infrastructures, moving the turbid waters into clear and erosive ones (Lavie, 2009), while the Tunuyán River and its tributaries were not transformed upstream our sample points (Lavie et al., 2013, under press). Finally, we studied an urban drinking waters network, in Khartoum, the capital of Sudan, one of the least developed countries, with chronic political crises. The nearly 6 million inhabitants of this settlement suffer many cuts and bad pressure at tap. Furthermore, Nile's waters that feed the network are summarily treated and then quite turbid, especially in summer during Nile's floods. This situation obliges the population to store and to decant water, transforming it into clear ones (Lavie and Hamza, 2013, under press). The results of our studies demonstrate that, generally, we can observe a correlation between increasing turbidity and bacteriology, and decreasing oximetry. This assumption is disproven in many cases: (1) the stagnant waters of Khartoum and (2) the clarified Mendoza River waters. Finally, (3) the seasonal anthropogenic uses of soil and waters in the Doubegue and Tunuyán Rivers have more impact on the bacteriological quality than the natural seasonality of the suspended solids because soil erosion has increased.

SLUDGE BATCH 4 BASELINE MELT RATE FURNACE AND SLURRY-FED MELT RATE FURNACE TESTS WITH FRITS 418 AND 510 (U)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M. E.; Jones, T. M.; Miller, D. H.

Several Slurry-Fed Melt Rate Furnace (SMRF) tests with earlier projections of the Sludge Batch 4 (SB4) composition have been performed.1,2 The first SB4 SMRF test used Frits 418 and 320, however it was found after the test that the REDuction/OXidation (REDOX) correlation at that time did not have the proper oxidation state for manganese. Because the manganese level in the SB4 sludge was higher than previous sludge batches tested, the impact of the higher manganese oxidation state was greater. The glasses were highly oxidized and very foamy, and therefore the results were inconclusive. After resolving this REDOX issue, Frits 418,more » 425, and 503 were tested in the SMRF with the updated baseline SB4 projection. Based on dry-fed Melt Rate Furnace (MRF) tests and the above mentioned SMRF tests, two previous frit recommendations were made by the Savannah River National Laboratory (SRNL) for processing of SB4 in the Defense Waste Processing Facility (DWPF). The first was Frit 503 based on the June 2006 composition projections.3 The recommendation was changed to Frit 418 as a result of the October 2006 composition projections (after the Tank 40 decant was implemented as part of the preparation plan). However, the start of SB4 processing was delayed due to the control room consolidation outage and the repair of the valve box in the Tank 51 to Tank 40 transfer line. These delays resulted in changes to the projected SB4 composition. Due to the slight change in composition and based on preliminary dry-fed MRF testing, SRNL believed that Frit 510 would increase throughput in processing SB4 in DWPF. Frit 418, which was used in processing Sludge Batch 3 (SB3), was a viable candidate and available in DWPF. Therefore, it was used during the initial SB4 processing. Due to the potential for higher melt rates with Frit 510, SMRF tests with the latest SB4 composition (1298 canisters) and Frits 510 and 418 were performed at a targeted waste loading (WL) of 35%. The '1298 canisters' describes the number of equivalent canisters that would be produced from the beginning of the current contract period before SB3 is blended with SB4. The melt rate for the SMRF SB4/Frit 510 test was 14.6 grams/minute. Due to cold cap mounding problems with the SMRF SB4/Frit 418 feed at 50 weight % solids that prevented a melt rate determination, this feed was diluted to 45 weight % solids. The melt rate for this diluted feed was 8.9 grams/minute. A correction factor of 1.2 for estimating the melt rate at 50 weight % solids from 45 weight % solids test results (based on previous SMRF testing5) was then used to estimate a melt rate of 10.7 grams/minute for SB4/Frit 418 at 50 weight % solids. Therefore, the use of Frit 510 versus Frit 418 with SB4 resulted in a higher melt rate (14.6 versus an estimated 10.7 grams/minute). For reference, a previous SMRF test with SB3/Frit 418 feed at 35% waste loading and 50 weight % solids resulted in a melt rate of 14.1 grams/minute. Therefore, depending on the actual feed rheology, the use of Frit 510 with SB4 could result in similar melt rates as experienced with SB3/Frit 418 feed in the DWPF.« less

Process Optimization for Solid Extraction, Flavor Improvement and Fat Removal in the Production of Soymilk From Full Fat Soy Flakes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prawiradjaja, Stanley

Traditionally soymilk has been made with whole soybeans; however, there are other alternative raw ingredients for making soymilk, such as soy flour or full-fat soy flakes. US markets prefer soymilk with little or no beany flavor. modifying the process or using lipoxygenase-free soybeans can be used to achieve this. Unlike the dairy industry, fat reduction in soymilk has been done through formula modification instead of by conventional fat removal (skimming). This project reports the process optimization for solids and protein extraction, flavor improvement and fat removal in the production of 5, 8 and 12 °Brix soymilk from full fat soymore » flakes and whole soybeans using the Takai soymilk machine. Proximate analyses, and color measurement were conducted in 5, 8 and 12 °Brix soymilk. Descriptive analyses with trained panelists (n = 9) were conducted using 8 and 12 °Brix lipoxygenase-free and high protein blend soy flake soymilks. Rehydration of soy flakes is necessary to prevent agglomeration during processing and increase extractability. As the rehydration temperature increases from 15 to 50 to 85 C, the hexanal concentration was reduced. Enzyme inactivation in soy flakes milk production (measured by hexanal levels) is similar to previous reports with whole soybeans milk production; however, shorter rehydration times can be achieved with soy flakes (5 to 10 minutes) compared to whole beans (8 to 12 hours). Optimum rehydration conditions for a 5, 8 and 12 °Brix soymilk are 50 C for 5 minutes, 85 C for 5 minutes and 85 C for 10 minutes, respectively. In the flavor improvement study of soymilk, the hexanal date showed differences between undeodorized HPSF in contrast to triple null soymilk and no differences between deodorized HPSF in contrast to deodorized triple null. The panelists could not differentiate between the beany, cereal, and painty flavors. However, the panelists responded that the overall aroma of deodorized 8 °Brix triple null and HPSF soymilk are lower than the undeodorized triple null and HPSF soymilk. The triple null soymilk was perceived to be more bitter than the HPSF soymilk by the sensory panel due to oxidation on the triple null soy flakes. This oxidation may produce other aroma that was not analyzed using the GC but noticed by the panelists. The sensory evaluation results did show that the deodorizer was able to reduce the soymilk aroma in HPSF soymilk so it would be similar to triple null soymilk at 8 °Brix level. Regardless of skimming method and solids levels, the fat from the whole soybean milk was removed less efficiently than soy flake milk (7 to 30% fat extraction in contrast to 50 to 80% fat extraction respectively). In soy flake milk, less fat was removed as the % solid increases regardless of the processing method. In whole soybean milk, the fat was removed less efficiently at lower solids level milk using the commercial dairy skimmer and more efficient at lower solids level using the centrifuge-decant method. Based on the Hunter L, a, b measurement, the color of the reduced fat soy flake milk yielded a darker, greener and less yellow colored milk than whole soymilk (α < 0.05), whereas no differences were noticed in reduced fat soybean milk (α < 0.05). Color comparison of whole and skim cow's milk showed the same the same trend as in the soymilk.« less

Ionic composition and greenhouse gases evaluation in Tietê River sediment and mud landfill

NASA Astrophysics Data System (ADS)

La-Scalea, M. A.; Fornaro, A.; Abreu, E. L.; Mendonça, C. A.

2012-04-01

There are 39 cities composing the Metropolitan Area of São Paulo (MASP) which has grown seven times during the last sixty years, reaching, in 2011, 19.3 million inhabitants. This fact associated with a strong industrial development provoked, among other consequences, a disordered urbanization along the most important river of the region: Tietê. About 100 Km of its 1,150 Km full extension crosses MASP and, during the 60's, Marginal Tietê roadway was constructed, occupying the river banks as access routes. Tietê River was straightened and several landfills were created with its deposit (sediment and mud). EACH-USP (46.50 W, 23.48 S) lies nowadays in one of these areas, where this work has been developed. Therefore, the goal is to evaluate the chemical composition (ionic and gases) and its variability in function of the depth levels using three wells, from 0.60 to 9.0 m of depth. The wells were perforated in September 2011, end of the dry weather. Each well owns a homemade multiport sampling device (HMSD), being possible to push gas and/or water up from 15 available ports. The gases measurements were carried out using a GEM-2000 plus (Landtec) portable analyzer. Aqueous samples containing solid material were taken at each level depth from ports of the HMSD. However, no water was found in some levels. All samples were kept cooled until analysis procedures. After decantation of the solid material, the supernatant liquid was divided in two portions, being its conductivity (Micronal conductimeter) and pH (pH-meter Metrohm 654 with combined glass electrode) measured with the former and ionic analysis with the latter, in which all samples were filtered (Millex 0.22 micrometer pores) before each ionic chromatographic analysis, using Metrohm 850 System, for the ions: sodium, ammonium, potassium, calcium, magnesium, chloride, nitrate and sulfate. The first sampling stage was carried out during November and December 2011 in the beginning of rainy season in the mid Spring. From all the analysis performed, a large variability of the results may be observed for both gases and ionic composition not only among the wells, but also among the different depth levels. Vertically, one of the wells (W2) showed the same percentage of gases, methane 55% and carbon dioxide 45%, at all depth levels, while the other two wells (W1 and W3) presented these gases percentages only under 5.0 m deep. Concerning oxygen, 25% of this gas was detected at 1.0 m under the surface in W1 and W3. In relation to aqueous samples, the most acidity was observed near the surface (0.60 m deep, W1), pH 4.65, while pH 7.88 was obtained under 5.0 m deep (W3). For ionic concentrations a large range was observed considering all wells, being the lowest values for sulfate, from 0.60 to 20 mg/l, and the highest values for ammonium, between 14 and 53 mg/l. These results variability can be associated to the different soil composition layers, as well as to the biodegradation process and the time confinement of the river material deposit.

Cross-Validation of Suspended Sediment Concentrations Derived from Satellite Imagery and Numerical Modeling of the 1997 New Year's Flood on the Feather River, CA

NASA Astrophysics Data System (ADS)

Kilham, N. E.

2009-12-01

Image analysis was applied to assess suspended sediment concentrations (SSC) predicted by a numerical model of 2D hydraulics and sediment transport (Telemac-2D), coupled to a solver for the advection-diffusion equation (SISYPHE) and representing 18 days of flooding over 70 kilometers of the lower Feather-Yuba Rivers. Sisyphe treats the suspended load as a tracer, removed from the flow if the bed shear velocity, u* is lower than an empirically derived threshold (ud* = 7.8E-3 m s-1). Agreement between model (D50 = 0.03 mm) and image-derived SSC (mg L-1) suggests that image interpretation could prove to be a viable approach for verifying spatially-distributed models of floodplain sediment transport if imagery is acquired for a particular flood and at a sufficient spatial and radiometric resolution. However, remotely derived SSC represents the integrated concentration of suspended sediment at the water surface. Hence, comparing SSC magnitudes derived from imagery and numerical modeling requires that a relationship is first established between the total suspended load and the portion of this load suspended within the optical range of the sensor (e.g., Aalto, 1995). Using the optical depth (0.5 m) determined from radiative transfer modeling, surface SSC measured from a 1/14/97 Landsat TM5 image (30 m) were converted to depth-integrated SSC with the Rouse (1937) equation. Surface concentrations were derived using a look-up table for the sensor to convert endmember fractions obtained from a spectral mixture analysis of the image. A two-endmember model (2.0 and 203 mg L-1) was used, with synthetic endmembers derived from optical and radiative transfer modeling and inversion of field spectra collected from the Sacramento and Feather Rivers and matched to measured SSC values. Remotely sensed SSC patterns were then compared to the Telemac results for the same day and time. Modeled concentrations are a function of both the rating curve boundary conditions, and the transport and deposition calculations. At each of three upstream channel boundaries, hourly SSC was derived from instantaneous discharge and SSC records at USGS gages for winter months (December-April) following dam closure on the Feather, Yuba, and Bear Rivers (r2 = 0.61; r2 = 0.81; r2 = 0.55). Model channel concentrations declined downstream from about 90 mg L-1 to 40 mg L-1 as sediment input was depleted through decanting of river water overbank, advection through floodplain channels, and deposition onto the floodplain. Similar downstream declines in the image values suggest that bed and bank erosion downstream of the major gages did not contribute much new sediment two weeks following the flood peak. Model predicted concentrations agree with image derived concentrations to within 10 mg L-1, although the model predicts a more rapid drawdown of floodplain flow than is apparent from the image. Aalto, R., 1995. Discordance between suspended sediment diffusion theory and observed sediment concentration profiles in rivers. M.S., University of Washington, Seattle, WA. Rouse, H.R., 1937. Modern conceptions of the mechanics of turbulence. Transactions, American Society of Civil Engineers, 102: 463-543.

SLUDGE BATCH 7B QUALIFICATION ACTIVITIES WITH SRS TANK FARM SLUDGE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.; Click, D.; Lambert, D.

2011-11-16

Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry - Sludge Batch 7b (SB7b) - be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from Hmore » Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL typically simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). With the tight schedule constraints for SB7b and the potential need for caustic addition to allow for an acceptable glass processing window, the qualification for SB7b was approached differently than past batches. For SB7b, SRNL prepared a Tank 51 and a Tank 40 sample for qualification. SRNL did not receive the qualification sample from Tank 51 nor did it simulate all of the Tank Farm washing and decanting operations. Instead, SRNL prepared a Tank 51 SB7b sample from samples of Tank 7 and Tank 51, along with a wash solution to adjust the supernatant composition to the final SB7b Tank 51 Tank Farm projections. SRNL then prepared a sample to represent SB7b in Tank 40 by combining portions of the SRNL-prepared Tank 51 SB7b sample and a Tank 40 Sludge Batch 7a (SB7a) sample. The blended sample was 71% Tank 40 (SB7a) and 29% Tank 7/Tank 51 on an insoluble solids basis. This sample is referred to as the SB7b Qualification Sample. The blend represented the highest projected Tank 40 heel (as of May 25, 2011), and thus, the highest projected noble metals content for SB7b. Characterization was performed on the Tank 51 SB7b samples and SRNL performed DWPF simulations using the Tank 40 SB7b material. This report documents: (1) The preparation and characterization of the Tank 51 SB7b and Tank 40 SB7b samples. (2) The performance of a DWPF Chemical Process Cell (CPC) simulation using the SB7b Tank 40 sample. The simulation included a Sludge Receipt and Adjustment Tank (SRAT) cycle, where acid was added to the sludge to destroy nitrite and reduce mercury, and a Slurry Mix Evaporator (SME) cycle, where glass frit was added to the sludge in preparation for vitrification. The SME cycle also included replication of five canister decontamination additions and concentrations. Processing parameters were based on work with a nonradioactive simulant. (3) Vitrification of a portion of the SME product and characterization and durability testing (as measured by the Product Consistency Test (PCT)) of the resulting glass. (4) Rheology measurements of the SRAT receipt, SRAT product, and SME product. This program was controlled by a Task Technical and Quality Assurance Plan (TTQAP), and analyses were guided by an Analytical Study Plan. This work is Technical Baseline Research and Development (R&D) for the DWPF. It should be noted that much of the data in this document has been published in interoffice memoranda. The intent of this technical report is bring all of the SB7b related data together in a single permanent record and to discuss the overall aspects of SB7b processing.« less

Cosmic Dust in ~50 KG Blocks of Blue Ice from Cap-Prudhomme and Queen Alexandra Range, Antarctica

NASA Astrophysics Data System (ADS)

Maurette, M.; Cragin, J.; Taylor, S.

1992-07-01

Favorable Antarctic blue ice fields have produced a large number of meteorite finds because of the ice ablation concentration process (Cassidy et al., 1982). Such ice fields should also concentrate cosmic dust grains including both spherules and unmelted micrometeorites. Here we present preliminary results of concentrations of cosmic dust grains in ice from two very different Antarctic blue ice fields. The first sample (~60 kg) was collected in January 1987 from the surface of the blue ice field at Cap-Prudhomme (CP), near the French station of Dumont d'Urville, by a team from the "Laboratoire de Glaciologie du CNRS" (A. Barnola). The second sample (~50 kg), was retrieved from a meteorite stranding surface near the Queen Alexandra range (QUE) by a team (M. Burger, W. Cassidy, and R.Walker) of the ANSMET 1990 field expedition in Antarctica. Both samples were transported frozen to the laboratory where they were subdivided and processed. The CP sample was cut with a stainless steel saw into 4 pieces while the QUE sample, which had the top surface identified, was cut into three equal (~15 cm) horizontal layers to provide constituent variability with depth. All subsequent work on both samples was performed in a class 100 clean room using procedures developed by M. de Angelis and M. Maurette aimed at minimizing the loss of extraterrestrial particles. Pieces of both samples were cleaned by rinsing thoroughly with ultrapure water (Milli-O) and then melted in polyethylene containers in a microwave oven. Aliquots were decanted for chemical analysis and the remaining meltwater was filtered through stainless steel sieves for collection of large (>30 micrometers) particles. Using a 30X binocular microscope particles were hand picked for subsequent SEM/EDX analyses. Our initial objective was to compare the cosmic dust concentration in ice from the two locations. But this comparison was only partial because in the CP-ice, only magnetic spherules of >50 micrometers were studied whereas the QUE-ice studies included measurements of the depth variation of various characteristics, such as the size distribution and concentration of both cosmic spherules and unmelted chondritic micrometeorites (AMMs), the concentrations of grains in the ~1-10-micrometer size range, and the concentration of trace elements in the ice. In addition both magnetic and nonmagnetic particles were collected from the QUE-ice. The concentration of chondritic spherules 50 micrometers in size is similar at both locations: in the CP-ice 5 spherules were found in 40 kg of residual ice (after cleaning), and 7 spherules (including a nonmagnetic one) were recovered from 50kg of QUE-ice. The QUE sample contained 11 AMMs (including 3 grains with sizes ~30-50 micrometers) resulting in a ratio of unmelted to melted micrometeorites with sizes >50 micrometers (~1), which is much lower than the CP ratio of >5 (obtained for particles subsequently recovered from 360 tons of CP-ice). The QUE sample showed that particles >100 micrometers in size are found primarily within the top 15 m of ice while smaller particles are found in the bottom layers (30-50 cm). In contrast to CP-ice, QUE-ice contains many annealed stress cracks, that etch very quickly in water. Despite the very different glaciological and climatological regimes at the CP and QUE ice fields, concentrations of cosmic spherules are surprisingly similar. The ratio of AMMs to spherules does vary, however. The depth variations of the characteristics of cosmic dust grains trapped in the ~50-cm-thick top layer of a blue ice field are already very useful to select favorable zones to collect micrometeorites. In addition, they might provide insight into both climatic and ice flow parameters. Acknowledgements. We thank W.A. Cassidy and G. Crozaz for comments and R.M. Walker for his support and interest. REFERENCES. Cassidy W.A. and Rancitelli L.A. (1982) Am. Scientist 70, 156-164.

Isotopic evidence for dead fish maintenance of Florida red tides, with implications for coastal fisheries over both source regions of the West Florida shelf and within downstream waters of the South Atlantic Bight

NASA Astrophysics Data System (ADS)

Walsh, J. J.; Weisberg, R. H.; Lenes, J. M.; Chen, F. R.; Dieterle, D. A.; Zheng, L.; Carder, K. L.; Vargo, G. A.; Havens, J. A.; Peebles, E.; Hollander, D. J.; He, R.; Heil, C. A.; Mahmoudi, B.; Landsberg, J. H.

2009-01-01

Toxic Florida red tides of the dinoflagellate Kareniabrevis have downstream consequences of 500-1000 km spatial extent. Fish stocks, shellfish beds, and harmful algal blooms of similar species occupy the same continental shelf waters of the southeastern United States, amounting to economic losses of more than 25 million dollars in some years. Under the aegis of the Center for Prediction of Red tides, we are now developing coupled biophysical models of the conditions that lead to red tides and impacted coastal fisheries, from the Florida Panhandle to Cape Hatteras. Here, a nitrogen isotope budget of the coastal food web of the West Florida shelf (WFS) and the downstream South Atlantic Bight (SAB) reaffirms that diazotrophs are the initial nutrient source for onset of red tides and now identifies clupeid fish as the major recycled nutrient source for their maintenance. The recent isotope budget of WFS and SAB coastal waters during 1998-2001 indicates that since prehistoric times of Timacua Indian settlements along the Georgia coast during 1075, ∼50% of the nutrients required for large red tides of >1 μg chl l -1 of K.brevis have been derived from nitrogen-fixers, with the other half from decomposing dead sardines and herrings. During 2001, >90% of the harvest of WFS clupeids was by large ichthyotoxic red tides of >10 μg chl l -1 of K.brevis, rather than by fishermen. After onset of the usual red tides in summer of 2006 and 2007, the simulated subsequent fall exports of Florida red tides in September 2007 to North Carolina shelf waters replicate observations of just ∼1 μg chl l -1 on the WFS that year. In contrast, the earlier red tides of >10 μg chl l -1 left behind off West Florida during 2006, with less physical export, are instead 10-fold larger than those of 2007. Earlier, 55 fish kills were associated with these coastal red tides during September 2006, between Tampa and Naples. Yet, only six fish kills were reported there in September 2007. With little export of red tides and their fish prey during the former year, the computed larger nutrient-sated, fish-fed growth rates of the model’s dinoflagellates also replicate satellite-observed daily increments of K.brevis during fall maintenance in 2006, compared to simulated smaller fish-starved growth rates of decanted red tides during fall 2007. During the last few decades, K.brevis has remained a “prudent predator” of some clupeids, i.e. Spanish sardine, whereas humans have now overfished other Florida stocks of both thread herring and Atlantic shad. Thus, future operational forecasts of the land falls and durations of Florida red tides, from Louisiana to North Carolina, as well as prudent management of regional fisheries of the southeastern United States, require consideration of negelected fish losses, at intermediate trophic levels, to algal predators. Some clupeids are harvested by K.brevis, but these fish are separately supported by a longer parallel diatom-based food chain of calanoid copepods, feeding the zooplanktivores and thence other piscivore fish predators, while intersecting the shorter food chain of just diazotrophs and red tide dinoflagellates, poorly grazed in turn by harpactacoid copepods. The distinct phytoplankton functional groups, different herbivores, as well as zoophagous and piscivore fishes, must all be formulated as explicit state variables of the next set of complex ecological models, cued by satellite data and driven by nested circulation models, within an ecosystem-based management paradigm of commercial and sport harvests of biotic marine resources at higher trophic levels of the WFS and SAB.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caroline Clifford; Andre Boehman; Chunshan Song

2008-03-31

The final report summarizes the accomplishments toward project goals during length of the project. The goal of this project was to integrate coal into a refinery in order to produce coal-based jet fuel, with the major goal to examine the products other than jet fuel. These products are in the gasoline, diesel and fuel oil range and result from coal-based jet fuel production from an Air Force funded program. The main goal of Task 1 was the production of coal-based jet fuel and other products that would need to be utilized in other fuels or for non-fuel sources, using knownmore » refining technology. The gasoline, diesel fuel, and fuel oil were tested in other aspects of the project. Light cycle oil (LCO) and refined chemical oil (RCO) were blended, hydrotreated to removed sulfur, and hydrogenated, then fractionated in the original production of jet fuel. Two main approaches, taken during the project period, varied where the fractionation took place, in order to preserve the life of catalysts used, which includes (1) fractionation of the hydrotreated blend to remove sulfur and nitrogen, followed by a hydrogenation step of the lighter fraction, and (2) fractionation of the LCO and RCO before any hydrotreatment. Task 2 involved assessment of the impact of refinery integration of JP-900 production on gasoline and diesel fuel. Fuel properties, ignition characteristics and engine combustion of model fuels and fuel samples from pilot-scale production runs were characterized. The model fuels used to represent the coal-based fuel streams were blended into full-boiling range fuels to simulate the mixing of fuel streams within the refinery to create potential 'finished' fuels. The representative compounds of the coal-based gasoline were cyclohexane and methyl cyclohexane, and for the coal-base diesel fuel they were fluorine and phenanthrene. Both the octane number (ON) of the coal-based gasoline and the cetane number (CN) of the coal-based diesel were low, relative to commercial fuels ({approx}60 ON for coal-based gasoline and {approx}20 CN for coal-based diesel fuel). Therefore, the allowable range of blending levels was studied where the blend would achieve acceptable performance. However, in both cases of the coal-based fuels, their ignition characteristics may make them ideal fuels for advanced combustion strategies where lower ON and CN are desirable. Task 3 was designed to develop new approaches for producing ultra clean fuels and value-added chemicals from refinery streams involving coal as a part of the feedstock. It consisted of the following three parts: (1) desulfurization and denitrogenation which involves both new adsorption approach for selective removal of nitrogen and sulfur and new catalysts for more effective hydrotreating and the combination of adsorption denitrogenation with hydrodesulfurization; (2) saturation of two-ring aromatics that included new design of sulfur resistant noble-metal catalysts for hydrogenation of naphthalene and tetralin in middle distillate fuels, and (3) value-added chemicals from naphthalene and biphenyl, which aimed at developing value-added organic chemicals from refinery streams such as 2,6-dimethylnaphthalene and 4,4{prime}-dimethylbiphenyl as precursors to advanced polymer materials. Major advances were achieved in this project in designing the catalysts and sorbent materials, and in developing fundamental understanding. The objective of Task 4 was to evaluate the effect of introducing coal into an existing petroleum refinery on the fuel oil product, specifically trace element emissions. Activities performed to accomplish this objective included analyzing two petroleum-based commercial heavy fuel oils (i.e., No. 6 fuel oils) as baseline fuels and three co-processed fuel oils, characterizing the atomization performance of a No. 6 fuel oil, measuring the combustion performance and emissions of the five fuels, specifically major, minor, and trace elements when fired in a watertube boiler designed for natural gas/fuel oil, and determining the boiler performance when firing the five fuels. Two different co-processed fuel oils were tested: one that had been partially hydrotreated, and the other a product of fractionation before hydrotreating. Task 5 focused on examining refining methods that would utilize coal and produce thermally stable jet fuel, included delayed coking and solvent extraction. Delayed coking was done on blends of decant oil and coal, with the goal to produce a premium carbon product and liquid fuels. Coking was done on bench scale and large laboratory scale cokers. Two coals were examined for co-coking, using Pittsburgh seam coal and Marfork coal product. Reactions in the large, laboratory scaled coker were reproducible in yields of products and in quality of products. While the co-coke produced from both coals was of sponge coke quality, minerals left in the coke made it unacceptable for use as anode or graphite grade filler.« less

First Report of the Fig Cyst Nematode, Heterodera fici Kirjanova, on Fig Tree, Ficus carica, in Ontario, Canada.

PubMed

Sun, Fengcheng; Henry, Neil; Yu, Qing

2017-06-01

Although fig trees are a popular ornamental fruit tree in subtropical regions, some hardy species, such as Ficus carica , have been grown in the west coast of British Columbia and southern Ontario in Canada. The fig cyst nematode, Heterodera fici Kirjanova, is a pest on fig plants, and the heavy infestation can cause retarded growth and yellowing of leaves (Maqbool et al., 1987). In the spring of 2016, a sample of rhizosphere from a potted fig ( F. carica ) seedling was submitted to the Nematology Laboratory, Canadian Food Inspection Agency. The sample was collected from a nursery in Niagara-on-the-Lake, Ontario, Canada, during an inspection to support export certification. The fig trees in the nursery had been grown in the outside fields during the growing seasons and potted and moved to indoor during the winters for last 3 years. The sample was subjected to a nematode extraction process, including decanting and sieving and misting, and lemon-shaped cysts and second-stage juveniles of Heterodera sp. were recovered from the sample examined. The morphological and molecular analyses of the cysts, vulval cone, and second-stage juveniles from both the roots and the crushed cysts identified the species as Heterodera fici Kirjanova. The cysts were characterized by their dark brown color and lemon shape, as well as distinct necks and vulval cones. The vulval cones were observed having an ambifenestrate fenestra (Fig. 1AFig. 1Photomicrographs of Heterodera fici on fig tree from Ontario, Canada. A, B. Cyst vulval cones with the ambifenestrate fenestra in A) and well-developed underbridge and bullae in B). C-E. The second-stage juveniles from a crushed cyst with the whole body in C), the anterior region in D) and the posterior region in E).), dome-shaped bullae scattered around the underbridge plane (Fig. 1B), well-developed underbridge (Fig. 1B), and coarse zig-zag ridges surrounding the fenestra on the surface. The cyst measurements ( n = 3) were length 608.7 ± 91.6 (506-682) µm, width = 395.3 ± 40.9 (366-442) µm, and length/width ratio = 1.3 ± 0.2 (1.3-1.7) µm. The morphometric characters of the vulval cone were fenestral length = 57.3 ± 2.9 (54-59) µm, fenestral width = 35.3 ± 4 (33-40) µm, and vulval slit = 50.7 ± 1.2 (50-52) µm. Second-stage juveniles tapering posteriorly (Fig. 1C). Stylet well developed, basal knobs rounded, directed slightly anteriorly (Fig. 1D). Tail tapering, with hyaline terminal about half of tail length (Fig. 1E). Second-stage juveniles ( n = 16) showed the following morphometric characters: body length = 440.9 ± 20 (408-470) µm, a = 20.3 ± 2.3 (16.9-24), b = 2.7 ± 0.3 (2.3-3.3), c = 8.1 ± 0.6 (7.3-9.3), c' = 3.8 ± 0.3 (3.1-4.3), stylet length = 23.2 ± 0.4 (23-24) µm, anterior end to median bulb = 71.8 ± 4.5 (65-79) µm; maximum body width = 21.9 ± 2 (17-25) µm; body width at anus = 14.4 ± 1.5 (12-17) µm, tail length = 54.6 ± 2.9 (50-60) µm, and hyaline part of tail = 23.7 ± 2.9 (19-28) µm. These observations conform to the published descriptions of Heterodera fici Kirjanova (Kirjanova, 1954; Golden et al., 1988). The slides of the cyst vulval cone and juveniles were deposited in the Canadian National collection of Insects, Arachnids, and Nematodes (Accession no. 14851 to 14853 for the second stage juveniles and 14854-14855 for the cyst cones). For molecular analysis, DNA was extracted from individual juvenile ( n = 4) from different cysts. A 1,151-bp fragment of ribosomal DNA containing ITS1-5.8S-ITS2 region was amplified and sequenced using primers 18S (5'-TTGATTACGTCCCTGCCCTTT-3') and 26S (5'- TTTCACTCGCCGTTACTAAGG-3') (Vrain et al., 1992). The sequence was deposited into the GenBank database (Accession no. KY635986 and KY635987) and was compared with published sequences by means of BLAST search in the database (November 2016). The comparison revealed 99.0% to 100% similarity to the sequences of the same genomic region of H. fici from Iran (AF498385) and Georgia (AF274409). Subbotin et al. (2010) summarized the known occurrence of the fig cyst nematode from Belarus, Belgium, Estonia, France, Germany, Greece, Hungary, Italy, The Netherlands, Norway, Poland, Portugal, Russia, Spain, Yugoslavia, China, Georgia, Iran, Turkey, Uzbekistan, Australia, New Zealand, United States (California, Florida, Louisiana, Maryland, and Virginia), Brazil, Algeria, and South Africa. It is an exotic pest to Canada. To our knowledge, this is the first evidence of the occurrence of H. fici in Canada.

Sediment transport and deposition in the lower Missouri River during the 2011 flood

USGS Publications Warehouse

Alexander, Jason S.; Jacobson, Robert B.; Rus, David L.

2013-01-01

Floodwater in the Missouri River in 2011 originated in upper-basin regions and tributaries, and then travelled through a series of large flood-control reservoirs, setting records for total runoff volume entering all six Missouri River main-stem reservoirs. The flooding lasted as long as 3 months. The U.S Geological Survey (USGS) examined sediment transport and deposition in the lower Missouri River in 2011 to investigate how the geography of floodwater sources, in particular the decanting effects of the Missouri River main-stem reservoir system, coupled with the longitudinal characteristics of civil infrastructure and valley-bottom topography, affected sediment transport and deposition in this large, regulated river system. During the flood conditions in 2011, the USGS, in cooperation with the U.S. Army Corps of Engineers, monitored suspended-sediment transport at six primary streamgages along the length of the lower Missouri River. Measured suspended-sediment concentration (SSC) in the lower Missouri River varied from approximately 150 milligrams per liter (mg/L) to 2,000 mg/L from January 1 to September 30, 2011. Median SSC increased in the downstream direction from 355 mg/L at Sioux City, Iowa, to 490 mg/L at Hermann, Missouri. The highest SSCs were measured downstream from Omaha, Nebraska, in late February when snowmelt runoff from tributaries, which were draining zones of high-sediment production, was entering the lower Missouri River, and releases of water at Gavins Point Dam were small. The combination of dilute releases of water at Gavins Point Dam and low streamflows in lower Missouri River tributaries caused sustained lowering of SSC at all streamgages from early July through late August. Suspended-sediment ranged from 5 percent washload (PW; percent silt and clay) to as much as 98 percent in the lower Missouri River from January 1 to September 30, 2011. Median PW increased in the downstream direction from 24 percent at Sioux City, Iowa, to 78 percent at Hermann, Missouri. Measurements made in early January, when SSC was low, indicate that suspended sediment mostly was composed of bed material, but by mid-February, runoff from the plains caused PW to increase at most streamgages. Total suspended-sediment discharge (SSD) during water year 2011 at the selected streamgages in the lower Missouri River ranged from approximately 29 to 64 million tons. Total estimated SSD had the lowest exceedance frequencies in the reaches between Gavins Point Dam and Nebraska City, Nebraska, but exceedance frequencies increased substantially downstream. In 2011, total SSD with low exceedance frequencies were reported at Sioux City, Iowa, Omaha, Nebraska, and Nebraska City, Nebraska, despite moderate-to-high exceedance frequencies for annual average SSC, indicating that the duration of high-magnitude flooding was the primary driver of total SSD. Comparison of median SSC for samples from water year 2011 with samples in the 20 years prior indicated that median SSC for high-action streamflows (streamflows likely to produce a stage exceeding the National Weather Service’s “action stage”) in 2011 were lower than those typical for high-action streamflows. Multiple-comparison analysis indicated that median SSC values for low-action streamflows (streamflows likely to produce stages lower than the National Weather Service’s “action stage”) and high-action streamflows sampled in 2011 at 4 of 6 streamgages were not significantly distinguishable from median SSC values for low-action streamflows in the previous 20 years. Longitudinal comparison of streamflow and SSD exceedance frequencies for 2011 with corresponding frequencies for 2008 and 1993 indicated the important role of tributary contributions to total SSD in the lower Missouri River. In 1993 and 2008, tributaries were the primary source of floodwater in the lower Missouri River, which resulted in a 20-fold increase in total SSD from Sioux City, Iowa, to Hermann, Missouri. In 2011, releases at Gavins Point Dam were the primary source of floodwater in the lower Missouri River, and total SSD at Hermann, Missouri, was only twice that estimated for Sioux City, Iowa. Sand deposition was estimated using analysis of multispectral satellite imagery collected in October and November 2011. Distributions of sand in the flood plain of the lower Missouri River also were quantified in relation to distance from the banks of the main channel for seven discrete river segments bounded by Gavins Point Dam and selected downstream tributaries. The areal extent of overbank flooding and flood-plain sand deposits increased downstream from Sioux City, Iowa to a broad peak near Rulo, Nebraska, and then decreased to levels near the lower limit of quantification downstream from Kansas City, Missouri. Most of the flood plain inundation and sediment-deposition damage to agricultural fields was observed between river miles 480 and 700, where 2011 peak streamflows had low exceedance frequencies, and the lower Missouri River channel was less incised or had aggraded recently. As channel capacity increased in the downstream direction, the relative magnitude of the flood decreased downstream, and overbank flooding was less extensive. In the constricted reaches, flood-plain sand deposits mainly were observed in association with levee breaks.

Pulsed Laser Annealing of Carbon

NASA Astrophysics Data System (ADS)

Abrahamson, Joseph P.

This dissertation investigates laser heating of carbon materials. The carbon industry has been annealing carbon via traditional furnace heating since at least 1800, when Sir Humphry Davy produced an electric arc with carbon electrodes made from carbonized wood. Much knowledge has been accumulated about carbon since then and carbon materials have become instrumental both scientifically and technologically. However, to this day the kinetics of annealing are not known due to the slow heating and cooling rates of furnaces. Additionally, consensus has yet to be reached on the cause of nongraphitizability. Annealing trajectories with respect to time at temperature are observed from a commercial carbon black (R250), model graphitizable carbon (anthracene coke) and a model nongraphitizable carbon (sucrose char) via rapid laser heating. Materials were heated with 1064 nm and 10.6 im laser radiation from a Q-switched Nd:YAG laser and a continuous wave CO2 laser, respectively. A pulse generator was used reduce the CO2 laser pulse width and provide high temporal control. Time-temperature-histories with nanosecond temporal resolution and temperature reproducibility within tens of degrees Celsius were determined by spectrally resolving the laser induced incandescence signal and applying multiwavelength pyrometry. The Nd:YAG laser fluences include: 25, 50, 100, 200, 300, and 550 mJ/cm2. The maximum observed temperature ranged from 2,400 °C to the C2 sublimation temperature of 4,180 °C. The CO2 laser was used to collect a series of isothermal (1,200 and 2,600 °C) heat treatments versus time (100 milliseconds to 30 seconds). Laser heated samples are compared to furnace annealing at 1,200 and 2,600 °C for 1 hour. The material transformation trajectory of Nd:YAG laser heated carbon is different than traditional furnace heating. The traditional furnace annealing pathway is followed for CO2 laser heating as based upon equivalent end structures. The nanostructure of sucrose char after 5 seconds of isothermal annealing at 2,600 °C is comprised almost entirely of quasi-spherical closed shell particles that are free of sp3 and oxygen content. With additional time at temperature the particles unravel and propagative particle opening occurs throughout the material. The irregular pore structure found in the end product is a result of particle unraveling. The structures found in heat treated sucrose char believed to contain odd membered rings are not manufactured during the annealing process due to impinging growth of stacks. Thus, odd membered rings are likely present in the starting non-graphitizable char. Furnace annealing of cokes and chars produced from: oxygen containing compounds (polyfurfuryl alcohol and anthanthrone), from a five membered ring containing polyaromatic hydrocarbon (fluorene), and from sulfur containing decant oil and a blend of anthracene-dibenzothiophene were compared to furnace annealed anthracene coke and sucrose char. The majority of initial oxygen content evolved out during low temperature carbonization. The intermediate species formed after oxygen evolution dictated the resulting carbon skeleton and thus the graphitizability. Carbonization of anthanthrone resulted in a graphitizable coke. It is proposed that carbon monoxide loss from anthanthrone results in the formation of perylene. An obvious resemblance was observed in structure between heat treated sucrose and polyfurfuryl alcohol char as compared to heated treated char embedded with 5 membered rings via carbonization of fluorene. Thus, providing evidence that 5 membered rings are present in the virgin chars and are the cause of non-graphitizability. The heteroatom sulfur effects carbon structure in a different way as compared to oxygen. Sulfur is thermally stable in carbon up to ˜ 1,000 °C and thus plays little role in the initial low temperature (500 °C) carbonization. As such it imparts a relatively unobservable impact on nanostructure, but rather acts to cause micro-cracks upon rapid evolution in the form of H2S and CS2, upon subsequent heat treatment. Laboratory generated synthetic soot from benzene and benzene-thiophene were Nd:YAG laser and furnace annealed. Furnace annealing of sulfur doped synthetic soot results in cracks and rupturing due to the high pressures caused by explosive sulfur evolution at elevated temperature. Whereas Nd:YAG laser heating of the sulfur doped sample acted to induce curvature. The observed curvature is owed to annealing occurring simultaneously with sulfur evolution. The unset lamellae are strongly influenced by the defect formed upon sulfur evolution. Coke and char samples were prepared via carbonization in sealed tubing reactors. The extent of mesophase development was assessed by measuring the materials optical anisotropy with a polarized light microscope. Physical and chemical transformations from annealing were measured with electron microscopy, energy dispersive X-ray spectroscopy, selected area electron diffraction, and electron energy loss spectroscopy. Virgin samples and traditional furnace annealed samples available in bulk were analyzed with X-ray diffraction. The potential technological importance of laser annealing carbon is demonstrated as annealing can be performed continuously and rapidly. Examples of material processing and synthesis not possible via traditional furnace annealing are provided.

Aquifer recharge with reclaimed water in the Llobregat Delta. Laboratory batch experiments and field test site.

NASA Astrophysics Data System (ADS)

Tobella, J.

2010-05-01

Summary Spain, as most other Mediterranean countries, faces near future water shortages, generalized pollution and loss of water dependent ecosystems. Aquifer recharge represents a promising option to become a source for indirect potable reuse purposes but presence of pathogens as well as organic and inorganic pollutants should be avoided. To this end, understanding the processes of biogeochemical degradation occurring within the aquifer during infiltration is capital. A set of laboratory batch experiments has been assembled in order to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. Data collected during laboratory experiments and monitoring activities at the Sant Vicenç dels Horts test site will be used to build and calibrate a numerical model (i) of the physical-chemical-biochemical processes occurring in the batches and (ii) of multicomponent reactive transport in the unsaturated/saturated zone at the test site. Keywords Aquifer recharge, batch experiments, emerging micropollutants, infiltration, numerical model, reclaimed water, redox conditions, Soil Aquifer Treatment (SAT). 1. Introduction In Spain, the Llobregat River and aquifers, which supply water to Barcelona, have been overexploited for years and therefore, suffer from serious damages: the river dries up on summer, riparian vegetation has disappeared and seawater has intruded the aquifer. In a global context, solutions to water stress problems are urgently needed yet must be sustainable, economical and safe. Recent developments of analytical techniques detect the presence of the so-called "emerging" organic micropollutants in water and soils. Such compounds may affect living organisms when occurring in the environment at very low concentrations (microg/l or ng/l). In wastewater and drinking water treatment plants, a remarkable removal of these chemicals from water can be obtained only using advanced and costly treatments. Nevertheless, a number of studies are demonstrating that physical, chemical and biochemical processes associated with water movement within the subsoil represent a natural alternative way to reduce the presence of these contaminants. This processes are called Soil Aquifer Treatment (SAT). Aquifer recharge will become a source for indirect potable reuse purposes as long as the presence of pathogens and organic and inorganic pollutants is avoided. To this end, understanding the biogeochemical degradation processes occurring within the aquifer during infiltration is capital. 2. Laboratory batch experiments A set of laboratory batch experiments has been assembled to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. The setup of the experiments consists of glass bottles containing 120 g of soil and 240 ml of synthetic water spiked with the mix of micropollutants. A source of easily degradable organic carbon and, depending on the type of test, electron acceptors are added in order to yield aerobic respiration and nitrate/iron/manganese/sulphate reduction conditions. The evolution of the processes is monitored by sacrificing duplicate bottles according to a defined schedule and analysing water for major and minor components as well as for micropollutants. Results from biotic tests are compared with abiotic ones in order to discern biodegradation from other chemical processes. The soil, the synthetic water and the micropollutants selected for the experiments are representative of a test site in the nearby of Barcelona (Spain) where artificial recharge of groundwater through ponds is going to be performed using river water or tertiary effluent from a waste water treatment plant. The results of the experiments improve the knowledge on the behaviour of the selected micropollutants under different redox conditions and provide with useful information on the conditions to develop at the test site during artificial recharge. The data collected during the laboratory experiments and in the test site will be used to build and calibrate a numerical model of the physical-chemical-biochemical processes developing in the batches and of multicomponent reactive transport in the unsaturated/saturated zone in the test site area. 3. Field test site The infiltration site of Sant Vicenç dels Horts has been selected to assessing the biogeochemical processes occurring during SAT. The system consists of two ponds that have been built as compensatory measure for the reduction in natural recharge caused by the construction of the High Speed Train Line. The first pond acts as a decantation pond while the second one acts as an infiltration basin (Figure 1). Recharge water comes from the tertiary treatment plant of the El Prat de Llobregat WWTP and the river (?). The CUADLL (Lower Llobregat Aquifer End-Users Community) is now managing the system operation. Tasks that are currently being carried out at this Test Site aims at (i) improving the local experience on MAR through infiltration ponds operational aspects and (ii) monitoring the changes in water quality during the recharge processes (unsaturated and saturated zone). Special attention is being paid to the fate of emerging organic pollutants (pharmaceuticals, surfactants, pesticides, etc.). The yielding of the monitoring will be compared with the results from the laboratory batch experiments on the behaviour of selected emerging organic pollutants. To this end, observation wells have been constructed, pressure / temperature / electrical conductivity transducers have been installed and the vadose zone under the infiltration pond has been instrumented (tensiometers, water content probes and suction cups). In addition double ring and infiltration tests have been performed in order to forecast the infiltration capacity of the basin.

Proceedings of the 25th Annual Stirling Physics Meeting 1999

NASA Astrophysics Data System (ADS)

McVey, Michael

1999-09-01

The 25th Annual Stirling Physics meeting took place on Thursday 20 May on a warm sunny day when the country setting of Stirling Campus could be seen at its best. A total of 225 participants from all sectors of physics education attended. There was an opportunity to view and discuss with exhibitors a wide range of state-of-the-art equipment and teaching materials both before and after the meeting. The theme of the meeting was `Maintaining Standards'. Gemmel Millar, Scottish Branch Secretary acting as Chairperson for the morning session and in anticipation of the first speaker, wondered if a new unit qualification, the `Planck' might be introduced. Half units would then be `Short Plancks' and how many Short Plancks must there be in a unit? Great stuff. Scottish Qualifications Authority Hugh McGill began with a brief history and description of the Scottish Qualifications Authority. Born on 1 April 1997 (a light frisson of amusement swept through the audience) it was a unification between SEB and SCOTVEC and has a range of responsibilities covering schools, further and higher education. It oversees Standard and Higher grades, HNC and HND and SVQs, and it has 500 full-time employees as well as some 13500 appointees who act as examiners, assessors and verifiers etc, without whom its remit could not be carried out. The committee structure of the Board was outlined, one each for national and higher national qualifications and a third for Scottish vocational qualifications. These will be served by a proposed 19 Advisory Groups. The Science Advisory Group will be the key body for advising SQA on strategic developments to ensure that qualifications meet the needs of both client groups and end users. A consultation paper `Added Value To Learning' was referred to, in which all qualifications available in Scotland are given parity of esteem on a rising 11-point scale. Mr McGill stated that standards would be best maintained by ensuring continuity in procedures developed over many years. The Physics Sub-panel would still exist. Nominees from this would serve on the Science Advisory Group. An Assessment Panel for physics would be created and a Principal Assessor would be appointed for three years to oversee both Higher and Advanced Higher. There would be continuity in retaining Arrangements Documents. National Physical Laboratory Metrology, the science of measurement, was the subject of a fascinating and wide-ranging talk by Dr Keith Berry. He described the origins of NPL, established in 1900 in Bushy House, a Royal property donated by Queen Victoria and not far from Hampton Court. Added to over the years, it now covers 60 acres and employs 700 staff, of whom 500 have professional qualifications in Metrology. NPL holds over 100 standards. Dr Berry, in addressing the fundamental units of mass, length and time, described the evolution of the standard metre, defined originally 200 years ago as one ten-millionth of the polar quadrant running through Paris but in reality referenced to a standard platinum bar. The bar and its variants survived until 1960 when the metre was referenced to the wavelength of light from 86Kr. It is currently defined in relation to the speed of 633 nm light emitted through a vacuum from a stabilized HeNeI laser (1983). Research was under way to redefine the standard kilogram with something more reliable than the current platinum iridium standard kg, accurate to only 1 part in 107, possibly by counting the number of Si atoms in a standard macroscopic sample. Refinements in the standard second led to the development of the atomic clock with an accuracy of 1 part in 1013. This will vary by no more than 1 second in 300000 years. It is now widely used in GPS satellite technology. All measurements have to be traceable back to a national standard but each step in the calibration chain results in a loss of accuracy. Towards the middle of the 19th century, anomalies in national standards (the UK for example had a different length standard for imports and exports!) resulted in the establishment of the Convention Du Mètre, an agreement on the definition of a standard metre to which all signatories would adhere. This now has 48 signatories and has given rise to the International Bureau of Weights and Measures located near Paris but technically not in France (merely surrounded by it). The French Government has accorded its couple of acres international status. The Bureau is the Secretariat to the International Committee on Weights and Measures and it is this committee which has overall responsibility for international standards. Dr Berry described a proposed international agreement which all national standards institutions will be required to sign. This will result in the production of a database listing the standards being used in all the participating countries and will be totally transparent. Uncertainties were touched on. A draft NPL document entitled `A Beginner's Guide to The Uncertainty of Measurement' already exists and will be made available to the profession in due course. The Scottish Branch was invited to have an input to this publication. Dr Berry concluded by describing a number of interesting everyday examples in which measurement was critically important. These ranged from calibration of aircraft altimeters by pressure measurement to the equalisation of National Lottery balls to a paltry 1/1000 inch (more non-SI units!). The audience was left with much to take back to the classroom from a valuable and entertaining presentation. Advancing Physics Philip Britton set the scene in a light-hearted and often hilarious introduction, e.g. `when you're in a room full of physicists you don't feel so awkward because everybody else is weird'. The Advancing Physics initiative, he explained, was an Institute of Physics response to a deteriorating situation within physics education in England and Wales, particularly in the following areas:

• too few young people south of the border are choosing to study physics;
• the ratio of boys to girls taking physics is too high;
• a restricted framework of A-level qualifications currently exists;
• there is a crisis in recruitment of physics teachers with only 60 signed up to train for next year.

Endovascular Laser Therapy for Varicose Veins

PubMed Central

2010-01-01

Executive Summary Objective The objective of the MAS evidence review was to conduct a systematic review of the available evidence on the safety, effectiveness, durability and cost–effectiveness of endovascular laser therapy (ELT) for the treatment of primary symptomatic varicose veins (VV). Background The Ontario Health Technology Advisory Committee (OHTAC) met on November 27, 2009 to review the safety, effectiveness, durability and cost-effectiveness of ELT for the treatment of primary VV based on an evidence-based review by the Medical Advisory Secretariat (MAS). Clinical Condition VV are tortuous, twisted, or elongated veins. This can be due to existing (inherited) valve dysfunction or decreased vein elasticity (primary venous reflux) or valve damage from prior thrombotic events (secondary venous reflux). The end result is pooling of blood in the veins, increased venous pressure and subsequent vein enlargement. As a result of high venous pressure, branch vessels balloon out leading to varicosities (varicose veins). Symptoms typically affect the lower extremities and include (but are not limited to): aching, swelling, throbbing, night cramps, restless legs, leg fatigue, itching and burning. Left untreated, venous reflux tends to be progressive, often leading to chronic venous insufficiency (CVI). A number of complications are associated with untreated venous reflux: including superficial thrombophlebitis as well as variceal rupture and haemorrhage. CVI often results in chronic skin changes referred to as stasis dermatitis. Stasis dermatitis is comprised of a spectrum of cutaneous abnormalities including edema, hyperpigmentation, eczema, lipodermatosclerosis and stasis ulceration. Ulceration represents the disease end point for severe CVI. CVI is associated with a reduced quality of life particularly in relation to pain, physical function and mobility. In severe cases, VV with ulcers, QOL has been rated to be as bad or worse as other chronic diseases such as back pain and arthritis. Lower limb VV is a common disease affecting adults and estimated to be the seventh most common reason for physician referral in the US. There is a strong familial predisposition to VV with the risk in offspring being 90% if both parents affected, 20% when neither is affected, and 45% (25% boys, 62% girls) if one parent is affected. Globally, the prevalence of VV ranges from 5% to 15% among men and 3% to 29% among women varying by the age, gender and ethnicity of the study population, survey methods and disease definition and measurement. The annual incidence of VV estimated from the Framingham Study was reported to be 2.6% among women and 1.9% among men and did not vary within the age range (40-89 years) studied. Approximately 1% of the adult population has a stasis ulcer of venous origin at any one time with 4% at risk. The majority of leg ulcer patients are elderly with simple superficial vein reflux. Stasis ulcers are often lengthy medical problems and can last for several years and, despite effective compression therapy and multilayer bandaging are associated with high recurrence rates. Recent trials involving surgical treatment of superficial vein reflux have resulted in healing and significantly reduced recurrence rates. Endovascular Laser Therapy for VV ELT is an image-guided, minimally invasive treatment alternative to surgical stripping of superficial venous reflux. It does not require an operating room or general anesthesia and has been performed in outpatient settings by a variety of medical specialties including surgeons (vascular or general), interventional radiologists and phlebologists. Rather than surgically removing the vein, ELT works by destroying, cauterizing or ablating the refluxing vein segment using heat energy delivered via laser fibre. Prior to ELT, colour-flow Doppler ultrasonography is used to confirm and map all areas of venous reflux to devise a safe and effective treatment plan. The ELT procedure involves the introduction of a guide wire into the target vein under ultrasound guidance followed by the insertion of an introducer sheath through which an optical fibre carrying the laser energy is advanced. A tumescent anesthetic solution is injected into the soft tissue surrounding the target vein along its entire length. This serves to anaesthetize the vein so that the patient feels no discomfort during the procedure. It also serves to insulate the heat from damaging adjacent structures, including nerves and skin. Once satisfactory positioning has been confirmed with ultrasound, the laser is activated. Both the laser fibre and the sheath are simultaneously, slowly and continuously pulled back along the length of the target vessel. At the end of the procedure, homeostasis is then achieved by applying pressure to the entry point. Adequate and proper compression stockings and bandages are applied after the procedure to reduce the risk of venous thromboembolism, and to reduce postoperative bruising and tenderness. Patients are encouraged to walk immediately after the procedure and most patients return to work or usual activity within a few days. Follow-up protocols vary, with most patients returning 1-3 weeks later for an initial follow-up visit. At this point, the initial clinical result is assessed and occlusion of the treated vessels is confirmed with ultrasound. Patients often have a second follow-up visit 1-3 months following ELT at which time clinical evaluation and ultrasound are repeated. If required, sclerotherapy may be performed during the ELT procedure or at any follow-up visits. Regulatory Status Endovascular laser for the treatment of VV was approved by Health Canada as a class 3 device in 2002. The treatment has been an insured service in Saskatchewan since 2007 and is the only province to insure ELT. Although the treatment is not an insured service in Ontario, it has been provided by various medical specialties since 2002 in over 20 private clinics. Methods Literature Search The MAS evidence-based review was performed as an update to the 2007 health technology review performed by the Australian Medical Services Committee (MSAC) to support public financing decisions. The literature search was performed on August 18, 2009 using standard bibliographic databases for studies published from January 1, 2007 to August 15, 2009. Search alerts were generated and reviewed for additional relevant literature up until October 1, 2009. Inclusion Criteria English language full-reports and human studies Original reports with defined study methodology Reports including standardized measurements on outcome events such as technical success, safety, effectiveness, durability, quality of life or patient satisfaction Reports involving ELT for VV (great or small saphenous veins) Randomized controlled trials (RCTs), systematic reviews and meta-analyses Cohort and controlled clinical studies involving > 1 month ultrasound imaging follow-up Exclusion Criteria Non systematic reviews, letters, comments and editorials Reports not involving outcome events such as safety, effectiveness, durability, or patient satisfaction following an intervention with ELT Reports not involving interventions with ELT for VV Pilot studies or studies with small samples ( < 50 subjects) Summary of Findings The MAS evidence search identified 14 systematic reviews, 29 cohort studies on safety and effectiveness, four cost studies and 12 randomized controlled trials involving ELT, six of these comparing endovascular laser with surgical ligation and saphenous vein stripping. Since 2007, 22 cohort studies involving 10,883 patients undergoing ELT of the great saphenous vein (GSV) have been published. Imaging defined treatment effectiveness of mean vein closure rates were reported to be greater than 90% (range 93%- 99%) at short term follow-up. Longer than one year follow-up was reported in five studies with life table analysis performed in four but the follow up was still limited at three and four years. The overall pooled major adverse event rate, including DVT, PE, skin burns or nerve damage events extracted from these studies, was 0.63% (69/10,883). The overall level of evidence of randomized trials comparing ELT with surgical ligation and vein stripping (n= 6) was graded as moderate to high. Recovery after treatment was significantly quicker after ELT (return to work median number of days, 4 vs. 17; p= .005). Major adverse events occurring after surgery were higher [(1.8% (n=4) vs. 0.4% (n = 1) 1 but not significantly. Treatment effectiveness as measured by imaging vein absence or closure, symptom relief or quality of life similar in the two treatment groups and both treatments resulted in statistically significantly improvements in these outcomes. Recurrence was low after both treatments at follow up but neovascularization (growth of new vessels, a key predictor of long term recurrence was significantly more common (18% vs. 1%; p = .001) after surgery. Although patient satisfaction was reported to be high (>80%) with both treatments, patient preferences evaluated through recruitment process, physician reports and consumer groups were strongly in favour of ELT. For patients minimal complications, quick recovery and dependability of outpatient scheduling were key considerations. As clinical effectiveness of the two treatments was similar, a cost-analysis was performed to compare differences in resources and costs between the two procedures. A budget impact analysis for introducing ELT as an insured service was also performed. The average case cost (based on Ontario hospital costs and medical resources) for surgical vein stripping was estimated to be $1,799. Because of the uncertainties with resources associated with ELT, in addition to the device related costs, hospital costs were varied and assumed to be the same as or less than (40%) those for surgery resulting in an average ELT case cost of $2,025 or $1,602. Based on the historical pattern of surgical vein stripping for varices a 5-year projection was made for annual volumes and costs. In Ontario in 2007/2008, 3481 surgical vein stripping procedures were performed, 28% for repeat procedures. Annual volumes of ELT currently being performed in the province in over 20 private clinics were estimated to be approximately 840. If ELT were publicly reimbursed, it was assumed that it would capture 35% of the vein stripping market in the first year and increase to 55% in subsequent years. Based on these assumptions if ELT were not publicly reimbursed, the province would be paying approximately $5.9 million and if ELT were reimbursed the province would pay $8.2 million if the hospital costs for ELT were the same as surgery and $7.1 million if the hospital costs were less (40%) than surgery. The conclusions on the comparative outcomes between laser ablation and surgical ligation and saphenous vein stripping are summarized in the table below (ES Table 1). ES Table 1: Outcome comparisons of ELT vs. surgery for VV Outcomes Comparisons Post procedural pain, minor complications ELT < Surgery Recovery ELT < Surgery Major adverse events ELT < Surgery Effectiveness - Imaging vein occlusion/ absence ELT ~ Surgery Effectiveness-Vein symptom improvement ELT ~ Surgery Effectiveness - Quality Of Life ELT ~ Surgery Recurrence ELT ~ Surgery Patient satisfaction ELT ~ Surgery Patient preference ELT > Surgery Procedure costs ELT ~ < Surgery Budget impact ELT > Surgery The outcomes of the evidence-based review on these treatments based on three different perspectives are summarized below: Patient Outcomes – ELT vs. Surgery ELT has a quicker recovery attributable to the decreased pain, lower minor complications, use of local anesthesia with immediate ambulation. ELT is as effective as surgery in the short term as assessed by imaging anatomic outcomes, symptomatic relief and HRQOL outcomes. Recurrence is similar but neovascularization, a key predictor of long term recurrence, is significantly higher with surgery. Patient satisfaction is equally high after both treatments but patient preference is much more strongly for ELT. Surgeons performing ELT are satisfied with treatment outcomes and regularly offer ELT as a treatment alternative to surgery. Clinical or Technical Advantages – ELT Over Surgery An endovascular approach can more easily and more precisely treat multilevel disease and difficult to treat areas ELT is an effective and a less invasive treatment for the elderly with VV and those with venous leg ulcers. System Outcomes – ELT Replacing Surgery ELT may offer system advantages in that the treatment can be offered by several medical specialties in outpatient settings and because it does not require an operating theatre or general anesthesia. The treatment may result in ↓ pre-surgical investigations, decanting of patients from OR, ↓ demand on anesthetists time, ↓ hospital stay, ↓decrease wait time for VV treatment and provide more reliable outpatient scheduling. Depending on the reimbursement mechanism for the treatment, however, it may also result in closure of outpatient clinics with an increasingly centralization of procedures in selected hospitals with large capital budgets resulting in larger and longer waiting lists. Procedure costs may be similar for the two treatments but the budget impact may be greater with insurance of ELT because of the transfer of the cases from the private market to the public payer system. PMID:23074409

Endovascular Radiofrequency Ablation for Varicose Veins

PubMed Central

2011-01-01

Executive Summary Objective The objective of the MAS evidence review was to conduct a systematic review of the available evidence on the safety, effectiveness, durability and cost–effectiveness of endovascular radiofrequency ablation (RFA) for the treatment of primary symptomatic varicose veins. Background The Ontario Health Technology Advisory Committee (OHTAC) met on August 26th, 2010 to review the safety, effectiveness, durability, and cost-effectiveness of RFA for the treatment of primary symptomatic varicose veins based on an evidence-based review by the Medical Advisory Secretariat (MAS). Clinical Condition Varicose veins (VV) are tortuous, twisted, or elongated veins. This can be due to existing (inherited) valve dysfunction or decreased vein elasticity (primary venous reflux) or valve damage from prior thrombotic events (secondary venous reflux). The end result is pooling of blood in the veins, increased venous pressure and subsequent vein enlargement. As a result of high venous pressure, branch vessels balloon out leading to varicosities (varicose veins). Symptoms typically affect the lower extremities and include (but are not limited to): aching, swelling, throbbing, night cramps, restless legs, leg fatigue, itching and burning. Left untreated, venous reflux tends to be progressive, often leading to chronic venous insufficiency (CVI). A number of complications are associated with untreated venous reflux: including superficial thrombophlebitis as well as variceal rupture and haemorrhage. CVI often results in chronic skin changes referred to as stasis dermatitis. Stasis dermatitis is comprised of a spectrum of cutaneous abnormalities including edema, hyperpigmentation, eczema, lipodermatosclerosis and stasis ulceration. Ulceration represents the disease end point for severe CVI. CVI is associated with a reduced quality of life particularly in relation to pain, physical function and mobility. In severe cases, VV with ulcers, QOL has been rated to be as bad or worse as other chronic diseases such as back pain and arthritis. Lower limb VV is a very common disease affecting adults – estimated to be the 7th most common reason for physician referral in the US. There is a very strong familial predisposition to VV. The risk in offspring is 90% if both parents affected, 20% when neither affected and 45% (25% boys, 62% girls) if one parent affected. The prevalence of VV worldwide ranges from 5% to 15% among men and 3% to 29% among women varying by the age, gender and ethnicity of the study population, survey methods and disease definition and measurement. The annual incidence of VV estimated from the Framingham Study was reported to be 2.6% among women and 1.9% among men and did not vary within the age range (40-89 years) studied. Approximately 1% of the adult population has a stasis ulcer of venous origin at any one time with 4% at risk. The majority of leg ulcer patients are elderly with simple superficial vein reflux. Stasis ulcers are often lengthy medical problems and can last for several years and, despite effective compression therapy and multilayer bandaging are associated with high recurrence rates. Recent trials involving surgical treatment of superficial vein reflux have resulted in healing and significantly reduced recurrence rates. Endovascular Radiofrequency Ablation for Varicose Veins RFA is an image-guided minimally invasive treatment alternative to surgical stripping of superficial venous reflux. RFA does not require an operating room or general anaesthesia and has been performed in an outpatient setting by a variety of medical specialties including surgeons and interventional radiologists. Rather than surgically removing the vein, RFA works by destroying or ablating the refluxing vein segment using thermal energy delivered through a radiofrequency catheter. Prior to performing RFA, color-flow Doppler ultrasonography is used to confirm and map all areas of venous reflux to devise a safe and effective treatment plan. The RFA procedure involves the introduction of a guide wire into the target vein under ultrasound guidance followed by the insertion of an introducer sheath through which the RFA catheter is advanced. Once satisfactory positioning has been confirmed with ultrasound, a tumescent anaesthetic solution is injected into the soft tissue surrounding the target vein along its entire length. This serves to anaesthetize the vein, insulate the heat from damaging adjacent structures, including nerves and skin and compresses the vein increasing optimal contact of the vessel wall with the electrodes or expanded prongs of the RF device. The RF generator is then activated and the catheter is slowly pulled along the length of the vein. At the end of the procedure, hemostasis is then achieved by applying pressure to the vein entry point. Adequate and proper compression stockings and bandages are applied after the procedure to reduce the risk of venous thromboembolism and to reduce postoperative bruising and tenderness. Patients are encouraged to walk immediately after the procedure. Follow-up protocols vary, with most patients returning 1 to 3 weeks later for an initial follow-up visit. At this point, the initial clinical result is assessed and occlusion of the treated vessels is confirmed with ultrasound. Patients often have a second follow-up visit 1 to 3 months following RFA at which time clinical evaluation and ultrasound are repeated. If required, additional procedures such as phlebectomy or sclerotherapy may be performed during the RFA procedure or at any follow-up visits. Regulatory Status The Closure System® radiofrequency generator for endovascular thermal ablation of varicose veins was approved by Health Canada as a class 3 device in March 2005, registered under medical device license 67865. The RFA intravascular catheter was approved by Health Canada in November 2007 for the ClosureFast catheter, registered under medical device license 16574. The Closure System® also has regulatory approvals in Australia, Europe (CE Mark) and the United States (FDA clearance). In Ontario, RFA is not an insured service and is currently being introduced in private clinics. Methods Literature Search The MAS evidence–based review was performed to support public financing decisions. The literature search was performed on March 9th, 2010 using standard bibliographic databases for studies published up until March, 2010. Inclusion Criteria English language full-reports and human studies Original reports with defined study methodologyReports including standardized measurements on outcome events such as technical success, safety, effectiveness, durability, quality of life or patient satisfaction Reports involving RFA for varicose veins (great or small saphenous veins)Randomized controlled trials (RCTs), systematic reviews and meta-analysesCohort and controlled clinical studies involving ≥ 1 month ultrasound imaging follow-up Exclusion Criteria Non systematic reviews, letters, comments and editorials Reports not involving outcome events such as safety, effectiveness, durability, or patient satisfaction following an intervention with RFAReports not involving interventions with RFA for varicose veinsPilot studies or studies with small samples (< 50 subjects) Summary of Findings The MAS evidence search on the safety and effectiveness of endovascular RFA ablation of VV identified the following evidence: three HTAs, nine systematic reviews, eight randomized controlled trials (five comparing RFA to surgery and three comparing RFA to ELT), five controlled clinical trials and fourteen cohort case series (four were multicenter registry studies). The majority (12⁄14) of the cohort studies (3,664) evaluating RFA for VV involved treatment with first generation RFA catheters and the great saphenous vein (GSV) was the target vessel in all studies. Major adverse events were uncommonly reported and the overall pooled major adverse event rate extracted from the cohort studies was 2.9% (105⁄3,664). Imaging defined treatment effectiveness of vein closure rates were variable ranging from 68% to 96% at post-operative follow-up. Vein ablation rate at 6-month follow-up was reported in four studies with rates close to 90%. Only one study reported vein closure rates at 2 years but only for a minority of the eligible cases. The two studies reporting on RFA ablation with the more efficient second generation catheters involved better follow-up and reported higher ablation rates close to 100% at 6-month follow-up with no major adverse events. A large prospective registry trial that recruited over 1,000 patients at thirty-four largely European centers reported on treatment success in six overlapping reports on selected patient subgroups at various follow-up points up to 5 year. However, the follow-up for eligible recruited patients at all time points was low resulting in inadequate estimates of longer term treatment efficacy. The overall level of evidence of randomized trials comparing RFA with surgical ligation and vein stripping (n = 5) was graded as low to moderate. In all trials RFA ablation was performed with first generation catheters in the setting of the operating theatre under general anaesthesia, usually without tumescent anaesthesia. Procedure times were significantly longer after RFA than surgery. Recovery after treatment was significantly quicker after RFA both with return to usual activity and return to work with on average a one week less of work loss. Major adverse events occurring after surgery were higher [(1.8% (n=4) vs. 0.4% (n = 1) than after RFA but not significantly. Treatment effectiveness measured by imaging defined vein absence or vein closure was comparable in the two treatment groups. Significant improvements in vein symptoms and quality of life over baseline were reported for both treatment groups. Improvements in these outcomes were significantly greater in the RFA group than the surgery group in the peri-operative period but not in later follow-up. Follow-up in these trials was inadequate to evaluate longer term recurrence for either treatment. Patient satisfaction was reported to be high for both treatments but was higher for RFA. The studies comparing endovascular treatment approaches for VV (RFA and ELT) were more limited. Three RCT studies compared RFA (two with the second generation catheter) with ELT but mainly focused on peri-procedural outcomes such as pain, complications and recovery. Vein ablation rates were not evaluated in the trials, except for one small trial involving bilateral VV. Pain responses in patients undergoing ablation were extremely variable and up to 2 weeks, mean pain levels were significantly less with RFA than ELT ablation but differences were not significant at one month. Recovery, evaluated as return to usual activity or return to work, however, was similar in the treatment groups. Vein symptom and QOL improvements were improved in both groups but were significantly better in the RFA group than the ELT group at 2 weeks, but not at one month. Vein ablation rates were evaluated in several controlled clinical studies comparing the treatments between centers or within centers between individuals or over time. Comparisons in these studies were inconsistent with vein ablation rates for RFA reported to be similar to, higher than and lower than those with ELT. Economic Analysis RFA and surgical vein stripping, the main comparator reimbursed by the public system, are comparable in clinical benefits. Hence a cost-analysis was conducted to identify the differences in resources and costs between both procedures and a budgetary impact analysis (BIA) was conducted to project costs over a 5- year period in the province of Ontario. The target population of this economic analysis was patients with symptomatic varicose veins and the primary analytic perspective was that of the Ministry of Health and Long-Term Care. The average case cost (based on Ontario hospital costs and medical resources) for surgical vein stripping was estimated to be $1,799. In order to calculate a procedural cost for RFA it was assumed that the hospital cost and physician labour fees, excluding anaesthesia and surgical assistance, were the same as vein stripping surgery. The manufacturer also provided details on the generator with a capital cost of $27,500 and a lifespan of 5 years and the disposables (catheter, sheath, guidewire) with a cost of $673 per case. The average case cost for RFA was therefore estimated to be $1,356. One-way sensitivity analysis was also conducted with hospital cost of RFA varied to 60% that of vein stripping surgery (average cost per case = $627.08) to calculate an impact to the province. Historical volumes of vein stripping surgeries in Ontario were used to project surgeries in a linear fashion up to five years into the future. Volumes for RFA and ELT were calculated based on share capture from the surgery market based on discussion with clinical expert opinion and existing private data based on discussion with the manufacturer. RFA is expected to compete with ELT and capture some of the market. If ELT is reimbursed by the public sector then numbers will continue to increase from previous private data and share capture from the conventional surgical treatment market. Therefore, RFA cases will also increase since it will be capturing a share of the ELT market. A budget impact to the province was then calculated by multiplying volumes by the cost of the procedure. RFA is comparable in clinical benefits to vein stripping surgery. It has the extra upfront cost of the generator and cost per case for disposables but does not require an operating theater, anaesthetist or surgical assistant fees. The impact to the province is expected to be 5 M by Year 5 with the introduction of new ELT and RFA image guided endovascular technologies and existing surgery for varicose veins. Conclusion The conclusions on the comparative outcomes between endovascular RFA and surgical ligation and saphenous vein stripping and between endovascular RFA and laser ablation for VV treatment are summarized in the table below (ES Table 1). ES Table 1 Outcome comparisons of RFA vs. surgery and RFA vs ELT for varicose veins Outcome Comparisons RFA vs Surgery RFA vs ELT Post procedural pain, minor complications RFA < Surgery RFA < ELT Recovery RFA < Surgery RFA ~ ELT Major adverse events RFA < Surgery RFA ~ ELT Effectiveness - Imaging vein occlusion/ absence RFA ~ Surgery RFA ? ELT Effectiveness -Vein symptom improvement RFA ~ Surgery RFA ~ ELT Effectiveness - Quality Of Life RFA ~ Surgery RFA ~ ELT Recurrence RFA ? Surgery RFA ? ELT Patient satisfaction RFA > Surgery RFA ? ELT Patient preference RFA > Surgery RFA ? ELT Procedure costs RFA < Surgery RFA ~ ELT Budget impact RFA < Surgery RFA ~ ELT ELT refers to endovascular laser ablation; RFA, radiofrequency ablation The outcomes of the evidence-based review on these treatments for VV based on different perspectives are summarized below: RFA First versus Second Generation Catheters and Segmental Ablation Ablation with second generation catheters and segmental ablation offered technical advantages with improved ease and significant decreases in procedure time. RFA ablation with second generation catheters is also no longer restricted to smaller (< 12 mm diameter) saphenous veins. The safety profile with the new device and method of energy delivery is as good as or improved over the first generation device. No major adverse events were reported in two multicenter prospective cohort studies in 6 month follow-up with over 500 patients. Post-operative complications such as bruising and pain were significantly less with RFA ablation with second generation catheters than ELT in two RCT trials.RFA treatment with second generation catheters has ablation rates that are higher than with first generation catheters and are more comparable with the consistently high rates of ELT. Endovascular RFA versus Surgery RFA has a quicker recovery attributable to decreased pain and lower minor complications.RFA, in the short term was comparable to surgery in treatment effectiveness as assessed by imaging defined anatomic outcomes such as vein closure, flow or reflux. Other treatment outcomes such as symptomatic relief and HRQOL were significantly improved in both groups and between group differences in the early peri-operative period were likely influenced by pain experiences. Longer term follow-up was inadequate to evaluate recurrence after either treatment.Patient satisfaction was high after both treatments but was higher for RFA than surgery. Endovascular RFA versus ELT RFA has significantly less post-operative pain than ELT but differences were not significant when pain was adjusted for analgesic use and pain differences between groups did not persist at 1 month follow-up.Treatment effectiveness, measured as symptom relief and QOL improvement were similar between the endovascular treatments in the short term (within 1 month) Treatment effectiveness measured as imaging defined vein ablation was not measured in any RCT trials (only for bilateral VV disease) and results were inconsistently reported in observational trials.Longer term follow-up was not available to assess recurrence after either treatment. System Outcomes – RFA Replacing Surgery or Competing with ELT RFA may offer system advantages in that the treatment can be offered by several medical specialties in outpatient settings and because it does not require an operating theatre or general anaesthesia. The treatment may result in decanting of patients from OR with decreased pre-surgical investigations, demand on anaesthetists’ time, hospital stay and wait time for VV treatment. It may also provide more reliable outpatient scheduling. Procedure costs may be less for endovascular approaches than surgery but the budget impact may be greater with insurance of RFA because of the transfer of cases from the private market to the public payer system.Competition between RFA and ELT endovascular approaches is likely to continue to stimulate innovation and technical changes to advance patient care and result in competitive pricing. PMID:23074413

An Integrated Biochemistry Laboratory, Including Molecular Modeling

NASA Astrophysics Data System (ADS)

Hall, Adele J. Wolfson Mona L.; Branham, Thomas R.

1996-11-01

The dilemma of designing an advanced undergraduate laboratory lies in the desire to teach and reinforce basic principles and techniques while at the same time exposing students to the excitement of research. We report here on a one-semester, project-based biochemistry laboratory that combines the best features of a cookbook approach (high success rate, achievement of defined goals) with those of an investigative, discovery-based approach (student involvement in the experimental design, excitement of real research). Individual modules may be selected and combined to meet the needs of different courses and different institutions. The central theme of this lab is protein purification and design. This laboratory accompanies the first semester of biochemistry (Structure and Function of Macromolecules, a course taken mainly by junior and senior chemistry and biological chemistry majors). The protein chosen as the object of study is the enzyme lysozyme, which is utilized in all projects. It is suitable for a student lab because it is easily and inexpensively obtained from egg white and is extremely stable, and its high isoelectric point (pI = 11) allows for efficient separation from other proteins by ion-exchange chromatography. Furthermore, a literature search conducted by the resourceful student reveals a wealth of information, since lysozyme has been the subject of numerous studies. It was the first enzyme whose structure was determined by crystallography (1). Hendrickson et al. (2) have previously described an intensive one-month laboratory course centered around lysozyme, although their emphasis is on protein stability rather than purification and engineering. Lysozyme continues to be the focus of much exciting new work on protein folding and dynamics, structure and activity (3 - 5). This lab course includes the following features: (i) reinforcement of basic techniques, such as preparation of buffers, simple enzyme kinetics, and absorption spectroscopy; (ii) experience with methods of protein purification; (iii) incorporation of appropriate controls into experiments; (iv) use of basic statistics in data analysis; (v) writing papers and grant proposals in accepted scientific style; (vi) peer review; (vii) oral presentation of results and proposals; and (viii) introduction to molecular modeling. Figure 1 illustrates the modular nature of the lab curriculum. Elements from each of the exercises can be separated and treated as stand-alone exercises, or combined into short or long projects. We have been able to offer the opportunity to use sophisticated molecular modeling in the final module through funding from an NSF-ILI grant. However, many of the benefits of the research proposal can be achieved with other computer programs, or even by literature survey alone. Figure 1.Design of project-based biochemistry laboratory. Modules (projects, or portions of projects) are indicated as boxes. Each of these can be treated independently, or used as part of a larger project. Solid lines indicate some suggested paths from one module to the next. The skills and knowledge required for protein purification and design are developed in three units: (i) an introduction to critical assays needed to monitor degree of purification, including an evaluation of assay parameters; (ii) partial purification by ion-exchange techniques; and (iii) preparation of a grant proposal on protein design by mutagenesis. Brief descriptions of each of these units follow, with experimental details of each project at the end of this paper. Assays for Lysozyme Activity and Protein Concentration (4 weeks) The assays mastered during the first unit are a necessary tool for determining the purity of the enzyme during the second unit on purification by ion exchange. These assays allow an introduction to the concept of specific activity (units of enzyme activity per milligram of total protein) as a measure of purity. In this first sequence, students learn a turbidimetric assay for lysozyme activity and a colorimetric one for protein concentration. Familiarity with the assays is reinforced by an independently designed project to modify a variable in one of these assays. The assay for lysozyme activity is that of Shugar (6), based on hydrolysis of a cell-wall suspension from the bacterium Micrococcus lysodeikticus, a substrate that is particularly sensitive to lysozyme. As the cell walls are broken down by the enzyme, the turbidity of the sample decreases. This decrease can be conveniently measured by following the decrease in absorbance at a wavelength of 450 nm, using a spectrophotometer or other device for measuring light scattering. The Bradford method (7), a standard assay, is used to determine protein concentration. Using the data from both lysozyme activity assays and protein concentration assays, students can calculate the specific activity for commercial lysozyme and an egg- white solution. These calculations clearly demonstrate the increase in specific activity with increasing purity, since the purified (commercial) preparation has a specific activity approximately 20-fold higher than that of the crude egg-white solution. Lysozyme Purification by Ion-Exchange Chromatography (5 weeks) As suggested by Strang (8), students can design a rational purification of lysozyme using ion-exchange chromatography when presented with information on the isoelectric point of the enzyme and the properties of ion- exchange resins. One week is spent discussing protein purification and the relative advantages and disadvantages of different resins. Each group has a choice of anion-exchange (DEAE) or cation-exchange (CM) resins. Because lysozyme is positively charged below a pH of 11, it will not be adsorbed to an anion-exchange resin, but will be adsorbed to the cation-exchange resin. Therefore, for the cation-exchange protocols, there are further options for methods of collecting and eluting the desired protein. A purification table, including information on yield, specific activity, and degree of purification, is constructed. As described by both Strang (8) and Hurst et al. (9), excellent purifications can be obtained by cation-exchange chromatography, especially when elution is carried out with a salt gradient. Even a stepwise elution yields a highly purified fraction. Students' results for degrees of purification using cation exchange range from 15- to 50-fold. Anion-exchange has been less successful, with purification factors less than 5, although the principle that the positively charged lysozyme will not be adsorbed to the resin is still noted. During the last lab for this project, the crude and purified fractions are analyzed by SDS - polyacrylamide gel electrophoresis. The results of electrophoresis correlate well with calculated purification results. It is very clear that for preparations with high degrees of purification, a single band corresponding to standard lysozyme is observed, whereas for the anion-exchange procedures, multiple contaminating bands are still present. Allowing the students to choose and plan their own purification scheme in consultation with the instructor not only gives them experience in experimental design, but also introduces some flexibility in the level of work expected from each student. Those students who have had much previous lab experience in other courses or who have done independent research can choose to carry out a complex purification scheme, giving them exposure to techniques they may not have used before, whereas students with less experience can be guided to a less demanding purification procedure. Grant Proposal on Protein Design (4 weeks) The culminating exercise is a library/computer project on protein design and engineering. The students propose mutational studies of lysozyme to study stability or mechanism, based on the enzyme's known structure. Perhaps the most exciting area in protein biochemistry today is protein design and engineering. This is an appropriate final project, since by then the students have an appreciation for the complexities of dealing with proteins and should be capable of planning an extension of the project. The students by this point are familiar with the structure of hen egg-white lysozyme (1). The structure of the corresponding enzyme from bacteriophage T4 has also been established (10) and rational site-directed mutagenesis has been carried out to answer specific questions about the factors that affect protein stability (11). The relationship between the two lysozymes can provide a starting point for the students' manipulations of the enzyme from hen egg white, especially since there are many amino acids conserved in the two structures (12). Many mutations for the hen enzyme have also been described (13), and students are expected to carry out literature searches beyond the references supplied. The students examine structure - function relationships and decide on changes they would like to make in the lysozyme molecule, based on energy calculations and the scientific literature describing previous mutations in this and similar proteins. Several potential mutation sites are illustrated in Figure 2. Figure 2.The active site of hen egg-white lysozyme. The back-bone structure of lysozyme is illustrated as a ribbon model, with side-chains for tryptophan 62, 63, and 108 as stick models. Atomic coordinates for lysozyme were obtained from the Protein Data Bank. The molecule was displayed and manipulated using Quanta (MSI) on an Iris Indigo Workstation (Silicon Graphics). The active site of the enzyme is depicted, with side-chains of three tryptophan residues indicated. These residues have been implicated in lysozyme's mechanism of action, although not in actual catalysis. Tryptophan residues 62 and 63 participate in hydrogen bonding to substrate, and steric hindrance with Trp 108 has been thought to induce conformational strain in the substrate, favoring the transition state (reviewed in ref 13). In order to evaluate the importance of these interactions, students have proposed conservative or radical mutations at these sites. Once they have changed the amino acid residue and allowed the model to reach a new minimum energy, they can measure interatomic distances to determine whether or not a substrate can fit into the active site and/or form hydrogen bonds. A subtle variation on mutation of Trp 108 was a proposal to mutate an adjacent alanine residue, such as to displace the Trp further toward the helix and open up the active site. Other mutations, outside of the active site, have been proposed to change the overall stability of the protein (e.g., Gly to Ala within an a-helix, or loss of a disulfide bond). This exercise illustrates the possibilities of modeling proteins. Because it requires that the students set certain parameters and defaults for structural prediction, it helps them to understand the limitations of modeling. The final paper takes the form of a grant proposal. It presents the purification results, rationale for the desired mutation, relevance to previous studies, an overview of techniques applicable to the study of the mutant, predictions as to the characteristics of the engineered protein, and a plan for its purification. These proposals pass through at least one stage of peer review, and each student gives an oral presentation. This project serves to tie together many concepts learned during both the lecture and laboratory portions of the course. As noted above, we have been able to acquire workstations and software for modeling through funding from an NSF-ILI grant. However, the research proposal exercise can be modified, depending on facilities available and the goals of a particular course. A literature survey alone yields a wealth of information on this enzyme, and students can design experiments in biochemistry or molecular biology to follow up on the papers they have read. Some recent textbooks are accompanied by diskettes that allow visualization of proteins on computer monitors, although not manipulation of the structures. Computer programs such as Hyperchem (Autodesk, Sausalito CA) and Nanovision (ACS Software) allow display of proteins using PDB coordinates, and students can make decisions about which residues to mutate based on their position in the natural structure or in analogous proteins. Peer review of student work is incorporated into many writing courses (14), as well other courses that require multiple drafts of papers. We have found it to be a useful exercise for students in this laboratory course, both for the short paper and the grant proposal, although some care must be taken that students do not reinforce one another's misconceptions about scientific writing. There are many advantages to the students to this two-stage writing process. Most superficial, but not unimportant, is that it forces them to have their ideas in some written form one week before the final assignment is due. More significantly, it is a part of their professional training. The peer reviews are, in general, full of thoughtful and useful advice to their colleagues. They also learn a good deal from reading other drafts - about styles of writing, effective use of figures and tables, and references that might be useful to their own projects. Feedback from students indicates that they particularly enjoy devising their own experimental plans and that they appreciate the chance to work under the different conditions of small groups and as individuals. Not all of the exercises described here will be appropriate for every undergraduate biochemistry laboratory. However, the principle of projects that take several weeks to develop, beginning with basic concepts and working up to independently designed experiments, can be adapted to many settings. Experimental Details for Each Project Enzyme Assay The substrate, Micrococcus lysodeikticus, is obtained from Sigma (St. Louis). A suspension (0.3 mg/mL) is prepared fresh in 0.1 M phosphate buffer, pH 6.24, each day. Commercial lysozyme (also from Sigma), 2 mg/mL, as well as a 1:5 dilution of egg white, both in the same phosphate buffer, are used as a source of enzyme. From the change in absorbance over the time of assay, students calculate the activity of each enzyme preparation in terms of units per milliliter. A unit of lysozyme activity is defined as the amount of enzyme that will produce a DeltaA450 of 0.001 per min at pH 6.24 at 25 oC. Linearity of the enzyme-catalyzed reaction over the course of 5 min is the criterion used to choose an appropriate dilution of each enzyme preparation. Although the activity of the enzyme is sensitive to effects of pH and ionic strength (15), if these variables are held constant, the assay is quite reproducible and is, in general, very suitable for monitoring purification procedures (16). Protein Assay Students are supplied with a standard solution of lysozyme at a concentration of 2 mg/mL and the Coomassie blue reagent, obtained from BioRad (Hercules, CA), from which they prepare standards over the range 75 to 1500 mg/mL. Unknowns (in this case, the egg-white solution) are diluted appropriately. A standard curve is prepared by plotting the average absorbance at 595 nm for each set of duplicate readings. Using this standard curve, students determine the protein concentration for each unknown sample. Independent Assay Project Working in pairs or groups of three, the students design an experiment in which they vary one condition in the enzyme assay for lysozyme or in the Bradford assay for total protein and determine the effects on the assay. Examples of conditions to be varied for the enzyme assay are enzyme concentration, time of incubation, substrate concentration, addition of salts, change in pH or ionic strength of buffer, and addition of sulfhydryl reagent. Examples of conditions to be varied for the protein assay are identity of the protein used as standard (e.g., bovine serum albumin rather than lysozyme), time of incubation, wavelength of measurement, addition of salts, and addition of detergent. In these independent projects, students sometimes discover ways to improve the methodology for the assays, and these improvements are incorporated into the suggested procedures for the rest of the semester. The results of this project are written up as a short paper in a style appropriate for a rapid communication in a scientific journal. The papers go through a round of peer review and revision. Ion-Exchange Chromatography Once each group has decided on a project and discussed the details with the instructor, they prepare their own buffers and equilibrate the resins. DEAE-Sephacel and CM-Sepharose, both from Pharmacia/LKB (Piscataway, NJ) are supplied, about 20 mL of packed resin for each egg-white preparation. (These resins can be regenerated and reused many times.) Each group uses one egg white for the entire purification project. The egg white is filtered through one layer of cheesecloth and diluted 5-fold with the starting buffer. The first step is done batchwise because of the viscosity of the sample. The diluted egg white is mixed with the resin for approximately 15 min, then centrifuged at 1500 μ g for 15 min. The supernatant, containing those proteins not adsorbed to the resin, is decanted. Subsequent washing and elution can then be carried out batchwise or by transferring to a column [1.5 - 20 cm Econocolumns (BioRad)]. The options for recovery of the enzyme from the CM resin include a batch or column method, elution by change in pH or ionic strength, and gradient or stepwise elution. Those carrying out elutions from a column use an automatic fraction collector; gradient formers are available for those who choose to elute with a linear salt gradient. When elution is carried out by a change in pH, it should be noted that lysozyme may precipitate near its isoelectric point, especially at low ionic strength. SDS - polyacrylamide gel electrophoresis is used to monitor purity of the final preparation. Using mini-gels (BioRad Mini-Protean II apparatus), each group can pour, run, and stain their own 8 7.3-cm gel within the lab period; destaining can be carried out at any time afterward. The main contaminating band observed is ovalbumin, at a molecular weight of 46,000. Computer Modeling Using the program Quanta (MSI, Burlington, MA) on Indigo workstations (Silicon Graphics, Hudson, MA), the students retrieve coordinates from an MSI version of the Protein Data Bank, display the structure, and rationalize what changes would occur with a mutated form of the protein. Even for those who do not have Quanta or analogous programs, structural coordinates are available through the Internet. Students are prepared for their independent use of the molecular modeling workstations through a series of tutorials during the course of the semester. These exercises require that the students become familiar with specific applications of Quanta, including setting secondary conformation and hydrogen bonds, energy calculations, selectively displaying parts of molecules, measuring interatomic distances, and editing existing proteins. This introduction to macromolecular modeling is comparable to that suggested by Harvey and Tan (17) as a brief introduction to the field. Peer Review For each writing assignment (short paper and grant proposal), one week of lab is devoted to the peer review process. Students are to come to lab with a draft of their paper and a cover letter to their reviewers, which states how far they believe they are in the writing process; what they like and don't like about their work at this stage; and in what specific areas they need help (e.g., audience level, organization, use of references). They exchange papers, reading two or three during the course of the lab period. For each paper, they fill out a peer review form, which requires that they summarize the paper; look for clarity of presentation, appropriate citations, and use of others' work; point out any problems in organization or grammar; and suggest the steps necessary to complete the paper. They then go over the peer review form with the writer, referring any questions or disagreements to the instructor. It is most helpful if the instructor can also read and comment on the draft. General comments on the level of detail included and any problems with the reasoning come more appropriately from the instructor than from peers. The paper is then revised and handed in on the following week. The final draft is accompanied by a summary of revisions and copies of all peer reviews. Students are graded on peer reviews and summaries of revisions and cover letters, as well as on the final paper. Acknowledgments The molecular modeling workstations and associated software were purchased with funding from NSF, Instrumentation and Laboratory Improvement program, grant DUE-9350843 to AJW, with matching funds from Wellesley College. Some of the equipment for protein purification was funded by a grant from the Howard Hughes Medical Institute to Wellesley College. The authors are grateful to Paul Reisberg for helpful discussions in the early stages of this project and to Margaret Merritt for a critical review of the manuscript. Literature Cited 1. Blake, C. C. F.; Jonhson, L. N.; Mair, G. A.; North, A. C. T.; Phillips. D. C.; Sarma, V. R. Proc. Roy. Soc. London Ser. B 1967, 167, 378 - 388. 2. Hendrickson, H. S.; Giannini, J. L.; Bergstrom, J. P.; Johnson, S. N.; Leland, P. A. Biochem. Educ. 1995, 23, 14 - 17. 3. Miranker, A., Robinson, C. V.; Radford, S. E.; Aplin, R. T.; Dobson, C. M. Science 1993, 262, 896 - 900. 4. Turner, M. A.; Howell, P. L. Prot. Sci. 1995, 4, 442 - 449. 5. Radmacher, M.; Fritz, M.; Hansma, H. G.; Hansma, P. Science 1994, 265, 1577 - 1579. 6. Shugar, D. Biochim. Biophys. Acta 1952, 8, 302 - 309. 7. Bradford, M. M. Anal. Biochem. 1976, 72, 248 - 254. 8. Strang, R. H. C. In Practical Biochemistry for Colleges; Wood, E. J., Ed.; Pergamon: Oxford, 1989; pp 43 - 44. 9. Hurst, M. O.; Keenan, M. V.; Son, C. C. J. Chem. Educ. 1992, 69, 850 - 851. 10. Matthews, B. W.; Remington, S. J. Proc. Natl. Acad. Sci. USA 1974, 71, 4178 - 4182. 11. Matthews, B. W.; Nicholson, H.; Becktel, W. J. Proc. Natl. Acad. Sci. USA 1987, 84, 6663 - 6667. 12. Matthews, B. W.; Remington, S. J.; Grutter, M. G.; Anderson, W. F. J. Mol. Biol. 1981, 147, 545 - 558. 13. Imoto, T.; Johnson, L; North, A.; Phillips, D.; Rupley, J. In The Enzymes, 3rd ed.; Boyer, P., Ed.; Academic: London, 1972; Vol. VII, Chapter 21. 14. Walvoord, B. Helping Students Write Well; MLA: New York, 1986; Chapter 4. 15. Davies, R. C.; Neuberger, A.; Wilson, B. M. Biochim. Biophys. Acta 1969, 178, 294 - 305. 16. Jolles, P. Meth. Enzymol 1962, 5, 137 - 140. 17. Harvey, S. C.; Tan, R. K.-Z. Biophys. J. 1992, 63, 1683 - 1688.