Electronic transport of bilayer graphene with asymmetry line defects

NASA Astrophysics Data System (ADS)

Zhao, Xiao-Ming; Wu, Ya-Jie; Chen, Chan; Liang, Ying; Kou, Su-Peng

2016-11-01

In this paper, we study the quantum properties of a bilayer graphene with (asymmetry) line defects. The localized states are found around the line defects. Thus, the line defects on one certain layer of the bilayer graphene can lead to an electric transport channel. By adding a bias potential along the direction of the line defects, we calculate the electric conductivity of bilayer graphene with line defects using the Landauer-Büttiker theory, and show that the channel affects the electric conductivity remarkably by comparing the results with those in a perfect bilayer graphene. This one-dimensional line electric channel has the potential to be applied in nanotechnology engineering. Project supported by the National Basic Research Program of China (Grant Nos. 2011CB921803 and 2012CB921704), the National Natural Science Foundation of China (Grant Nos. 11174035, 11474025, 11504285, and 11404090), the Specialized Research Fund for the Doctoral Program of Higher Education, China, the Fundamental Research Funds for the Central Universities, China, the Scientific Research Program Fund of the Shaanxi Provincial Education Department, China (Grant No. 15JK1363), and the Young Talent Fund of University Association for Science and Technology in Shaanxi Province, China.

Construction Productivity Advancement Research (CPAR) Program: Improved Materials and Processes for Sealing and Resealing Joints in Portland Cement Concrete Pavements - Field Evaluation

DTIC Science & Technology

1993-10-01

sealant was determined by noting the type and number of defects each sealant incurred. Figure 4 provides a sample evaluation sheet used dur- ing the field...was conducted by visually inspect- ing the mater~al for defects . If any defects were noted, the type of defect was described and the quant~ty of that... defect was measured. The quantity of the defect was dividted by the total quantity of sealant and the result reported as percent defect . Adhesion and

40 CFR 85.1903 - Emissions defect information report.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Emissions defect information report. 85.1903 Section 85.1903 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements...

Seven Q-Tracks monitors of laboratory quality drive general performance improvement: experience from the College of American Pathologists Q-Tracks program 1999-2011.

PubMed

Meier, Frederick A; Souers, Rhona J; Howanitz, Peter J; Tworek, Joseph A; Perrotta, Peter L; Nakhleh, Raouf E; Karcher, Donald S; Bashleben, Christine; Darcy, Teresa P; Schifman, Ron B; Jones, Bruce A

2015-06-01

Many production systems employ standardized statistical monitors that measure defect rates and cycle times, as indices of performance quality. Clinical laboratory testing, a system that produces test results, is amenable to such monitoring. To demonstrate patterns in clinical laboratory testing defect rates and cycle time using 7 College of American Pathologists Q-Tracks program monitors. Subscribers measured monthly rates of outpatient order-entry errors, identification band defects, and specimen rejections; median troponin order-to-report cycle times and rates of STAT test receipt-to-report turnaround time outliers; and critical values reporting event defects, and corrected reports. From these submissions Q-Tracks program staff produced quarterly and annual reports. These charted each subscriber's performance relative to other participating laboratories and aggregate and subgroup performance over time, dividing participants into best and median performers and performers with the most room to improve. Each monitor's patterns of change present percentile distributions of subscribers' performance in relation to monitoring durations and numbers of participating subscribers. Changes over time in defect frequencies and the cycle duration quantify effects on performance of monitor participation. All monitors showed significant decreases in defect rates as the 7 monitors ran variously for 6, 6, 7, 11, 12, 13, and 13 years. The most striking decreases occurred among performers who initially had the most room to improve and among subscribers who participated the longest. All 7 monitors registered significant improvement. Participation effects improved between 0.85% and 5.1% per quarter of participation. Using statistical quality measures, collecting data monthly, and receiving reports quarterly and yearly, subscribers to a comparative monitoring program documented significant decreases in defect rates and shortening of a cycle time for 6 to 13 years in all 7 ongoing clinical laboratory quality monitors.

Evaluating practical vs. theoretical inspection system capability with a new programmed defect test mask designed for 3X and 4X technology nodes

NASA Astrophysics Data System (ADS)

Glasser, Joshua; Pratt, Tim

2008-10-01

Programmed defect test masks serve the useful purpose of evaluating inspection system sensitivity and capability. It is widely recognized that when evaluating inspection system capability, it is important to understand the actual sensitivity of the inspection system in production; yet unfortunately we have observed that many test masks are a more accurate judge of theoretical sensitivity rather than real-world usable capability. Use of ineffective test masks leave the purchaser of inspection equipment open to the risks of over-estimating the capability of their inspection solution and overspecifying defect sensitivity to their customers. This can result in catastrophic yield loss for device makers. In this paper we examine some of the lithography-related technology advances which place an increasing burden on mask inspection complexity, such as MEEF, defect printability estimation, aggressive OPC, double patterning, and OPC jogs. We evaluate the key inspection system component contributors to successful mask inspection, including what can "go wrong" with these components. We designed and fabricated a test mask which both (a) more faithfully represents actual production use cases; and (b) stresses the key components of the inspection system. This mask's patterns represent 32nm, 36nm, and 45nm logic and memory technology including metal and poly like background patterns with programmed defects. This test mask takes into consideration requirements of advanced lithography, such as MEEF, defect printability, assist features, nearly-repetitive patterns, and data preparation. This mask uses patterns representative of 32nm, 36nm, and 45nm logic, flash, and DRAM technology. It is specifically designed to have metal and poly like background patterns with programmed defects. The mask is complex tritone and was designed for annular immersion lithography.

Establishing of National Birth Defects Registry in Thailand.

PubMed

Pangkanon, Suthipong; Sawasdivorn, Siraporn; Kuptanon, Chulaluck; Chotigeat, Uraiwan; Vandepitte, Warunee

2014-06-01

Deaths attributed to birth defects are a major cause of infant and under-five mortality as well as lifetime disabilities among those who survive. In Thailand, birth defects contribute to 21% of neonatal deaths. There is currently no systematic registry for congenital anomalies in Thailand. Queen Sirikit National Institute of Child Health has initiated a Thailand Birth Defects Registry to capture birth defects among newborn infants. To establish the national birth defects registry in order to determine the burden of birth defects in Thailand. The birth defects data come from four main sources: National Birth Registry Database; National Health Security Office's reimbursement database; Online Birth Defect Registry Database designed to capture new cases that were detected later; and birth defects data from 20 participated hospitals. All data are linked by unique 13-digit national identification number and International Classification of Diseases (ICD)-10 codes. This registry includes 19 common structural birth defects conditions and pilots in 20 hospitals. The registry is hospital-based, hybrid reporting system, including only live births whose information was collected up to 1 year of age. 3,696 infants out of 67,813 live births (8.28% of total live births in Thailand) were diagnosed with congenital anomalies. The prevalence rate of major anomalies was 26.12 per 1,000 live births. The five most common birth defects were congenital heart defects, limb anomalies, cleft lip/cleft palate, Down syndrome, and congenital hydrocephalus respectively. The present study established the Birth Defects Registry by collecting data from four databases in Thailand. Information obtained from this registry and surveillance is essential in the planning for effective intervention programs for birth defects. The authors suggest that this program should be integrated in the existing public health system to ensure sustainability.

38 CFR 21.8012 - Vocational training program for certain children of Vietnam veterans-spina bifida and covered...

Code of Federal Regulations, 2010 CFR

2010-07-01

... program for certain children of Vietnam veterans-spina bifida and covered birth defects. 21.8012 Section... REHABILITATION AND EDUCATION Vocational Training and Rehabilitation for Certain Children of Vietnam Veterans... children of Vietnam veterans—spina bifida and covered birth defects. VA will provide an evaluation to an...

A 2011 Risk/Benefit Analysis of the Anthrax Vaccine Immunization Program

DTIC Science & Technology

2011-06-10

filled with botulinum toxin, 10 with anthrax, and 2 with aflatoxin.‖18 In 1992, Ken Alibek, a senior Russian bioweapons program manager defected...William K. Honner, Rosha A. Loach , Cynthia A. Moore, and J. David Erickson. ―Birth Defects Among Infants Born to Women Who Received Anthrax Vaccine In

Defect printability of ArF alternative phase-shift mask: a critical comparison of simulation and experiment

NASA Astrophysics Data System (ADS)

Ozawa, Ken; Komizo, Tooru; Ohnuma, Hidetoshi

2002-07-01

An alternative phase shift mask (alt-PSM) is a promising device for extending optical lithography to finer design rules. There have been few reports, however, on the mask's ability to identify phase defects. We report here an alt-PSM of a single-trench type with undercut for ArF exposure, with programmed phase defects used to evaluate defect printability by measuring aerial images with a Zeiss MSM193 measuring system. The experimental results are simulated using the TEMPEST program. First, a critical comparison of the simulation and the experiment is conducted. The actual measured topographies of quartz defects are used in the simulation. Moreover, a general simulation study on defect printability using an alt-PSM for ArF exposure is conducted. The defect dimensions, which produce critical CD errors, are determined by simulation that takes into account the full 3-dimensional structure of phase defects as well as a simplified structure. The critical dimensions of an isolated bump defect identified by the alt-PSM of a single-trench type with undercut for ArF exposure are 300 nm in bottom dimension and 74 degrees in height (phase) for the real shape, where the depth of wet-etching is 100 nm and the CD error limit is +/- 5 percent.

Defect printability of alternating phase-shift mask: a critical comparison of simulation and experiment

NASA Astrophysics Data System (ADS)

Ozawa, Ken; Komizo, Tooru; Kikuchi, Koji; Ohnuma, Hidetoshi; Kawahira, Hiroichi

2002-07-01

An alternative phase shift mask (alt-PSM) is a promising device for extending optical lithography to finer design rules. There have been few reports, however, on the mask's ability to identify phase defects. We report here an alt-PSM of a dual-trench type for KrF exposure, with programmed quartz defects used to evaluate defect printability by measuring aerial images with a Zeiss MSM100 measuring system. The experimental results are simulated using the TEMPEST program. First, a critical comparison of the simulation and the experiment is conducted. The actual measured topography of quartz defects are used in the simulation. Moreover, a general simulation study on defect printability using an alt-PSM for ArF exposure is conducted. The defect dimensions, which produce critical CD errors are determined by simulation that takes into account the full 3-dimensional structure of phase defects as well as a simplified structure. The critical dimensions of an isolated defect identified by the alt-PSM of a single-trench type for ArF exposure are 240 nm in bottom diameter and 50 degrees in height (phase) for the cylindrical shape and 240 nm in bottom diameter and 90 degrees in height (phase) for the rotating trapezoidal shape, where the CD error limit is +/- 5%.

40 CFR 1068.501 - How do I report emission-related defects?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Electronic control units, aftertreatment devices, fuel-metering components, EGR-system components, crankcase...) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR HIGHWAY, STATIONARY, AND NONROAD PROGRAMS Reporting Defects and Recalling Engines/Equipment § 1068.501 How do I report emission-related defects? This...

40 CFR 1068.501 - How do I report emission-related defects?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Electronic control units, aftertreatment devices, fuel-metering components, EGR-system components, crankcase...) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR HIGHWAY, STATIONARY, AND NONROAD PROGRAMS Reporting Defects and Recalling Engines/Equipment § 1068.501 How do I report emission-related defects? This...

40 CFR 1068.501 - How do I report emission-related defects?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Electronic control units, aftertreatment devices, fuel-metering components, EGR-system components, crankcase...) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR HIGHWAY, STATIONARY, AND NONROAD PROGRAMS Reporting Defects and Recalling Engines/Equipment § 1068.501 How do I report emission-related defects? This...

HgCdTe Surface and Defect Study Program.

DTIC Science & Technology

1986-03-01

different potential for Hg and Cd and hence be reflected in the electronic structure. The techniques of PES and ARPES available to our research group ...D-A166 795 HOME SURFCE ND DEFECT STUDY PROQRN(U) SATA / BARBRA RESEARCH CENTER GOLETA CALXF J A WILSON ET AL. USI FE MAR 86 SBRC-60411 ND93-63-C...0168 FO2/2 N L6 ILO 1.5 1. 11111 .6 .ICnrnp CHR HgCdTo SURFACE AND DEFECT STUDY PROGRAM J. A. Wilson and V. A. Cotton Santa Barbara Research Center

STARL -- a Program to Correct CCD Image Defects

NASA Astrophysics Data System (ADS)

Narbutis, D.; Vanagas, R.; Vansevičius, V.

We present a program tool, STARL, designed for automatic detection and correction of various defects in CCD images. It uses genetic algorithm for deblending and restoring of overlapping saturated stars in crowded stellar fields. Using Subaru Telescope Suprime-Cam images we demonstrate that the program can be implemented in the wide-field survey data processing pipelines for production of high quality color mosaics. The source code and examples are available at the STARL website.

Inspection of imprint lithography patterns for semiconductor and patterned media

NASA Astrophysics Data System (ADS)

Resnick, Douglas J.; Haase, Gaddi; Singh, Lovejeet; Curran, David; Schmid, Gerard M.; Luo, Kang; Brooks, Cindy; Selinidis, Kosta; Fretwell, John; Sreenivasan, S. V.

2010-03-01

Imprint lithography has been shown to be an effective technique for replication of nano-scale features. Acceptance of imprint lithography for manufacturing will require demonstration that it can attain defect levels commensurate with the requirements of cost-effective device production. This work summarizes the results of defect inspections of semiconductor masks, wafers and hard disks patterned using Jet and Flash Imprint Lithography (J-FILTM). Inspections were performed with optical and e-beam based automated inspection tools. For the semiconductor market, a test mask was designed which included dense features (with half pitches ranging between 32 nm and 48 nm) containing an extensive array of programmed defects. For this work, both e-beam inspection and optical inspection were used to detect both random defects and the programmed defects. Analytical SEMs were then used to review the defects detected by the inspection. Defect trends over the course of many wafers were observed with another test mask using a KLA-T 2132 optical inspection tool. The primary source of defects over 2000 imprints were particle related. For the hard drive market, it is important to understand the defectivity of both the template and the imprinted disk. This work presents a methodology for automated pattern inspection and defect classification for imprint-patterned media. Candela CS20 and 6120 tools from KLA-Tencor map the optical properties of the disk surface, producing highresolution grayscale images of surface reflectivity, scattered light, phase shift, etc. Defects that have been identified in this manner are further characterized according to the morphology

Making Use of a Decade of Widely Varying Historical Data: SARP Project - "Full Life-Cycle Defect Management"

NASA Technical Reports Server (NTRS)

Shull, Forrest; Godfrey, Sally; Bechtel, Andre; Feldmann, Raimund L.; Regardie, Myrna; Seaman, Carolyn

2008-01-01

A viewgraph presentation describing the NASA Software Assurance Research Program (SARP) project, with a focus on full life-cycle defect management, is provided. The topics include: defect classification, data set and algorithm mapping, inspection guidelines, and tool support.

A comprehensive defect data bank for no. 2 common oak lumber

Treesearch

Edwin L. Lucas; Leathern R.R. Catron; Leathern R.R. Catron

1973-01-01

Computer simulation of rough mill cut-up operations allows lowcost evaluation of furniture rough mill cut-up procedures. The defect data bank serves as input to such simulation programs. The data bank contains a detailed accounting of defect data taken from 637 No. 2 Common oak boards. Included is a description of each defect (location, size, and type), as well as the...

38 CFR 21.8282 - Termination of a vocational training program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for Certain Children of Vietnam Veterans-Spina Bifida and Covered Birth Defects Vocational Training..., administrative error, or finding that the child no longer has a covered birth defect. An eligible child for whom... covered birth defect. The effective date of termination will be the earliest of the following applicable...

Printability and inspectability of programmed pit defects on teh masks in EUV lithography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, I.-Y.; Seo, H.-S.; Ahn, B.-S.

2010-03-12

Printability and inspectability of phase defects in ELlVL mask originated from substrate pit were investigated. For this purpose, PDMs with programmed pits on substrate were fabricated using different ML sources from several suppliers. Simulations with 32-nm HP L/S show that substrate pits with below {approx}20 nm in depth would not be printed on the wafer if they could be smoothed by ML process down to {approx}1 nm in depth on ML surface. Through the investigation of inspectability for programmed pits, minimum pit sizes detected by KLA6xx, AIT, and M7360 depend on ML smoothing performance. Furthermore, printability results for pit defectsmore » also correlate with smoothed pit sizes. AIT results for pattemed mask with 32-nm HP L/S represents that minimum printable size of pits could be {approx}28.3 nm of SEVD. In addition, printability of pits became more printable as defocus moves to (-) directions. Consequently, printability of phase defects strongly depends on their locations with respect to those of absorber patterns. This indicates that defect compensation by pattern shift could be a key technique to realize zero printable phase defects in EUVL masks.« less

Enhancement of the Computer Lumber Grading Program to Support Polygonal Defects

Treesearch

Powsiri Klinkhachorn; R. Kathari; D. Yost; Philip A. Araman

1993-01-01

Computer grading of hardwood lumber promises to avoid regrading of the same lumber because of disagreements between the buyer and the seller. However, the first generation of computer programs for hardwood lumber grading simplify the process by modeling defects on the board as rectangles. This speeds up the grading process buy can inadvertently put a board into a lower...

National Newborn Screening and Genetics Resource Center

MedlinePlus

... GENERAL INFORMATION Conditions Screened by US Programs General Resources Genetics Birth Defects Hearing Screening FOR PROFESSIONALS ACT Sheets(ACMG) General Resources Newborn Screening Genetics Birth Defects FOR FAMILIES FAQs ...

A study of irradiation-induced defects in silicon using low temperature photoluminescence

NASA Technical Reports Server (NTRS)

Streetman, B. G.

1971-01-01

Irradiation-induced defects in silicon, using low temperature photoluminescence as a probe of defect properties were investigated. The goal of this research was to gain new understanding of defects which degrade solar cell characteristics in a radiation environment. In this regard, an important aspect of this program was a study of radiation damage and annealing in lithium doped silicon, which is useful in reducing solar cell degradation. Luminescence was used to study defects because this property reveals electron transitions through a number of defect energy levels at any given annealing stage; the luminescence spectra give excellent resolution of many defect energy levels, and these measurements can be used to give defect symmetry in the lattice, impurity dependence, and annealing properties.

Technique for writing of fiber Bragg gratings over or near preliminary formed macro-structure defects in silica optical fibers

NASA Astrophysics Data System (ADS)

Evtushenko, Alexander S.; Faskhutdinov, Lenar M.; Kafarova, Anastasia M.; Kazakov, Vadim S.; Kuznetzov, Artem A.; Minaeva, Alina Yu.; Sevruk, Nikita L.; Nureev, Ilnur I.; Vasilets, Alexander A.; Andreev, Vladimir A.; Morozov, Oleg G.; Burdin, Vladimir A.; Bourdine, Anton V.

2017-04-01

This work presents method for performing precision macro-structure defects "tapers" and "up-tapers" written in conventional silica telecommunication multimode optical fibers by commercially available field fusion splicer with modified software settings and following writing fiber Bragg gratings over or near them. We developed technique for macrodefect geometry parameters estimation via analysis of photo-image performed after defect writing and displayed on fusion splicer screen. Some research results of defect geometry dependence on fusion current and fusion time values re-set in splicer program are represented that provided ability to choose their "the best" combination. Also experimental statistical researches concerned with "taper" and "up-taper" diameter stability as well as their insertion loss values during their writing under fixed corrected splicer program parameters were performed. We developed technique for FBG writing over or near macro-structure defect. Some results of spectral response measurements produced for short-length samples of multimode optical fiber with fiber Bragg gratings written over and near macro-defects prepared by using proposed technique are presented.

Amelia: A Multi-Center Descriptive Epidemiologic Study in a Large Dataset from the International Clearinghouse for Birth Defects Surveillance and Research, and Overview of the Literature

PubMed Central

BERMEJO-SÁNCHEZ, EVA; CUEVAS, LOURDES; AMAR, EMMANUELLE; BAKKER, MARIAN K.; BIANCA, SEBASTIANO; BIANCHI, FABRIZIO; CANFIELD, MARK A.; CASTILLA, EDUARDO E.; CLEMENTI, MAURIZIO; COCCHI, GUIDO; FELDKAMP, MARCIA L.; LANDAU, DANIELLE; LEONCINI, EMANUELE; LI, ZHU; LOWRY, R. BRIAN; MASTROIACOVO, PIERPAOLO; MUTCHINICK, OSVALDO M.; RISSMANN, ANKE; RITVANEN, ANNUKKA; SCARANO, GIOACCHINO; SIFFEL, CSABA; SZABOVA, ELENA; MARTÍNEZ-FRÍAS, MARÍA-LUISA

2015-01-01

This study describes the epidemiology of congenital amelia (absence of limb/s), using the largest series of cases known to date. Data were gathered by 20 surveillance programs on congenital anomalies, all International Clearinghouse for Birth Defects Surveillance and Research members, from all continents but Africa, from 1968 to 2006, depending on the program. Reported clinical information on cases was thoroughly reviewed to identify those strictly meeting the definition of amelia. Those with amniotic bands or limb-body wall complex were excluded. The primary epidemiological analyses focused on isolated cases and those with multiple congenital anomalies (MCA). A total of 326 amelia cases were ascertained among 23,110,591 live births, stillbirths and (for some programs) elective terminations of pregnancy for fetal anomalies. The overall total prevalence was 1.41 per 100,000 (95% confidence interval: 1.26–1.57). Only China Beijing and Mexico RYVEMCE had total prevalences, which were significantly higher than this overall total prevalence. Some under-registration could influence the total prevalence in some programs. Liveborn cases represented 54.6% of total. Among monomelic cases (representing 65.2% of nonsyndromic amelia cases), both sides were equally involved, and the upper limbs (53.9%) were slightly more frequently affected. One of the most interesting findings was a higher prevalence of amelia among offspring of mothers younger than 20 years. Sixty-nine percent of the cases had MCA or syndromes. The most frequent defects associated with amelia were other types of musculoskeletal defects, intestinal, some renal and genital defects, oral clefts, defects of cardiac septa, and anencephaly. PMID:22002956

Simulation based mask defect repair verification and disposition

NASA Astrophysics Data System (ADS)

Guo, Eric; Zhao, Shirley; Zhang, Skin; Qian, Sandy; Cheng, Guojie; Vikram, Abhishek; Li, Ling; Chen, Ye; Hsiang, Chingyun; Zhang, Gary; Su, Bo

2009-10-01

As the industry moves towards sub-65nm technology nodes, the mask inspection, with increased sensitivity and shrinking critical defect size, catches more and more nuisance and false defects. Increased defect counts pose great challenges in the post inspection defect classification and disposition: which defect is real defect, and among the real defects, which defect should be repaired and how to verify the post-repair defects. In this paper, we address the challenges in mask defect verification and disposition, in particular, in post repair defect verification by an efficient methodology, using SEM mask defect images, and optical inspection mask defects images (only for verification of phase and transmission related defects). We will demonstrate the flow using programmed mask defects in sub-65nm technology node design. In total 20 types of defects were designed including defects found in typical real circuit environments with 30 different sizes designed for each type. The SEM image was taken for each programmed defect after the test mask was made. Selected defects were repaired and SEM images from the test mask were taken again. Wafers were printed with the test mask before and after repair as defect printability references. A software tool SMDD-Simulation based Mask Defect Disposition-has been used in this study. The software is used to extract edges from the mask SEM images and convert them into polygons to save in GDSII format. Then, the converted polygons from the SEM images were filled with the correct tone to form mask patterns and were merged back into the original GDSII design file. This merge is for the purpose of contour simulation-since normally the SEM images cover only small area (~1 μm) and accurate simulation requires including larger area of optical proximity effect. With lithography process model, the resist contour of area of interest (AOI-the area surrounding a mask defect) can be simulated. If such complicated model is not available, a simple optical model can be used to get simulated aerial image intensity in the AOI. With built-in contour analysis functions, the SMDD software can easily compare the contour (or intensity) differences between defect pattern and normal pattern. With user provided judging criteria, this software can be easily disposition the defect based on contour comparison. In addition, process sensitivity properties, like MEEF and NILS, can be readily obtained in the AOI with a lithography model, which will make mask defect disposition criteria more intelligent.

Defective TFH Cell Function and Increased TFR Cells Contribute to Defective Antibody Production in Aging.

PubMed

Sage, Peter T; Tan, Catherine L; Freeman, Gordon J; Haigis, Marcia; Sharpe, Arlene H

2015-07-14

Defective antibody production in aging is broadly attributed to immunosenescence. However, the precise immunological mechanisms remain unclear. Here, we demonstrate an increase in the ratio of inhibitory T follicular regulatory (TFR) cells to stimulatory T follicular helper (TFH) cells in aged mice. Aged TFH and TFR cells are phenotypically distinct from those in young mice, exhibiting increased programmed cell death protein-1 expression but decreased ICOS expression. Aged TFH cells exhibit defective antigen-specific responses, and programmed cell death protein-ligand 1 blockade can partially rescue TFH cell function. In contrast, young and aged TFR cells have similar suppressive capacity on a per-cell basis in vitro and in vivo. Together, these studies reveal mechanisms contributing to defective humoral immunity in aging: an increase in suppressive TFR cells combined with impaired function of aged TFH cells results in reduced T-cell-dependent antibody responses in aged mice. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Detection of incipient defects in cables by partial discharge signal analysis

NASA Astrophysics Data System (ADS)

Martzloff, F. D.; Simmon, E.; Steiner, J. P.; Vanbrunt, R. J.

1992-07-01

As one of the objectives of a program aimed at assessing test methods for in-situ detection of incipient defects in cables due to aging, a laboratory test system was implemented to demonstrate that the partial discharge analysis method can be successfully applied to low-voltage cables. Previous investigations generally involved cables rated 5 kV or higher, while the objective of the program focused on the lower voltages associated with the safety systems of nuclear power plants. The defect detection system implemented for the project was based on commercially available signal analysis hardware and software packages, customized for the specific purposes of the project. The test specimens included several cables of the type found in nuclear power plants, including artificial defects introduced at various points of the cable. The results indicate that indeed, partial discharge analysis is capable of detecting incipient defects in low-voltage cables. There are, however, some limitations of technical and non-technical nature that need further exploration before this method can be accepted in the industry.

Ontological Modeling of Transformation in Heart Defect Diagrams

PubMed Central

Viswanath, Venkatesh; Tong, Tuanjie; Dinakarpandian, Deendayal; Lee, Yugyung

2006-01-01

The accurate portrayal of a large volume data of variable heart defects is crucial to providing good patient care in pediatric cardiology. Our research aims to span the universe of congenital heart defects by generating illustrative diagrams that enhance data interpretation. To accommodate the range and severity of defects to be represented, we base our diagrams on transformation models applied to a normal heart rather than a static set of defects. These models are based on a domain-specific ontology, clustering, association rule mining and the use of parametric equations specified in a mathematical programming language. PMID:17238451

This Issue: Correlates of a Defective School.

ERIC Educational Resources Information Center

Gilman, David Alan

1992-01-01

Describes correlates of defective schools: perks for very few; faulty communication; adult-centered programs; special interest group indulgence; poor professional relationships; personnel warehousing; incompetent consultants; literal interpretation of technicalities; imperial leadership; intimate relationships among personnel; incoherent…

Prevalence of birth defects among American-Indian births in California, 1983-2010.

PubMed

Aggarwal, Deepa; Warmerdam, Barbara; Wyatt, Katrina; Ahmad, Shabbir; Shaw, Gary M

2015-02-01

Approximately 6.3 million live births and fetal deaths occurred during the ascertainment period in the California Birth Defects Monitoring Program registry. American-Indian and non-Hispanic white women delivered 40,268 and 2,044,118 births, respectively. While much information has been published about non-Hispanic white infants, little is known regarding the risks of birth defects among infants born to American-Indian women. This study used data from the California Birth Defects Monitoring Program to explore risks of selected birth defects in offspring of American-Indian relative to non-Hispanic white women in California. The study population included all live births and fetal deaths 20 weeks or greater from 1983 to 2010. Prevalence ratios and corresponding 95% confidence intervals (CI) were computed using Poisson regression for 51 groupings of birth defects. Prevalence ratios were estimated for 51 groupings of birth defects. Of the 51, nine had statistically precise results ranging from 0.78 to 1.85. The eight groups with elevated risks for American-Indian births were reduction deformities of brain, anomalies of anterior segments, specified anomalies of ear, ostium secundum type atrial septal defect, specified anomalies of heart, anomalies of the aorta, anomalies of great veins, and cleft lip with cleft palate. Our results suggest that American-Indian women having babies in California may be at higher risk for eight birth defect phenotypes compared with non-Hispanic whites. Further research is needed to determine whether these risks are observed among other populations of American-Indian women or when adjusted for potential covariates. © 2015 Wiley Periodicals, Inc.

Self-passivation Rule and the Effect of Post-treatment in GBs of Solar Cell Materials

NASA Astrophysics Data System (ADS)

Liu, Chengyan; Chen, Shiyou; Xiang, Hongjun; Gong, Xingao

Grain boundaries (GBs) existing in polycrystalline semiconductors alloys inducing a great deal of deep defect levels are usually harmful to cells' photovoltaic performance. Experimental and theoretical investigations verified that these defect levels come from the GBs' dangling bonds. We find that, the defect levels in anion core of GB can be passivated by its cations, called by self-passivation. For instance, the post-treated by CdCl2, Cd can eliminate the defect levels by saturating Te dangling bonds in the grain boundary of CdTe. We verify that the idea of self-passivation rule can perfectly explain the benign GBs of CISe and CZTS by sodium treatment. The present work reveals a general mechanism about how dopants in GBs eliminate the defect states through passivating the dangling bonds in covalent polycrystalline semiconductors, and sheds light on how to passivate dangling bonds in GBs with alterative processes. National Science Foundation of China, international collaboration project of MOST, Pujiang plan, Program for Professor of Special Appointment (Eastern Scholar), and Shanghai Rising-star program.

On-line high-speed rail defect detection, phase III : research results.

DOT National Transportation Integrated Search

2005-10-01

The Federal Railroad Administration (FRA) Office of Research and Developments Track and Structures Program sponsored a study for developing and testing a rail defect detection system based on ultrasonic guided waves and non-contact probing. Curren...

Massively parallel E-beam inspection: enabling next-generation patterned defect inspection for wafer and mask manufacturing

NASA Astrophysics Data System (ADS)

Malloy, Matt; Thiel, Brad; Bunday, Benjamin D.; Wurm, Stefan; Mukhtar, Maseeh; Quoi, Kathy; Kemen, Thomas; Zeidler, Dirk; Eberle, Anna Lena; Garbowski, Tomasz; Dellemann, Gregor; Peters, Jan Hendrik

2015-03-01

SEMATECH aims to identify and enable disruptive technologies to meet the ever-increasing demands of semiconductor high volume manufacturing (HVM). As such, a program was initiated in 2012 focused on high-speed e-beam defect inspection as a complement, and eventual successor, to bright field optical patterned defect inspection [1]. The primary goal is to enable a new technology to overcome the key gaps that are limiting modern day inspection in the fab; primarily, throughput and sensitivity to detect ultra-small critical defects. The program specifically targets revolutionary solutions based on massively parallel e-beam technologies, as opposed to incremental improvements to existing e-beam and optical inspection platforms. Wafer inspection is the primary target, but attention is also being paid to next generation mask inspection. During the first phase of the multi-year program multiple technologies were reviewed, a down-selection was made to the top candidates, and evaluations began on proof of concept systems. A champion technology has been selected and as of late 2014 the program has begun to move into the core technology maturation phase in order to enable eventual commercialization of an HVM system. Performance data from early proof of concept systems will be shown along with roadmaps to achieving HVM performance. SEMATECH's vision for moving from early-stage development to commercialization will be shown, including plans for development with industry leading technology providers.

Neural Tube Defects in Costa Rica, 1987–2012: Origins and Development of Birth Defect Surveillance and Folic Acid Fortification

PubMed Central

de la Paz Barboza-Argüello, María; Umaña-Solís, Lila M.; Azofeifa, Alejandro; Valencia, Diana; Flores, Alina L.; Rodríguez-Aguilar, Sara; Alfaro-Calvo, Thelma; Mulinare, Joseph

2015-01-01

Our aim was to provide a descriptive overview of how the birth defects surveillance and folic acid fortification programs were implemented in Costa Rica—through the establishment of the Registry Center for Congenital Anomalies (Centro de Registro de Enfermedades Congénitas—CREC), and fortification legislation mandates. We estimated the overall prevalence of neural tube defects (i.e., spina bifida, anencephaly and encephalocele) before and after fortification captured by CREC. Prevalence was calculated by dividing the total number of infants born with neural tube defects by the total number of live births in the country (1987–2012).A total of 1,170 newborns with neural tube defects were identified from 1987 to 2012 (1992–1995 data excluded); 628 were identified during the baseline pre-fortification period (1987–1991; 1996–1998); 191 during the fortification period (1999–2002); and 351 during the post-fortification time period (2003–2012). The overall prevalence of neural tube defects decreased from 9.8 per 10,000 live-births (95 % CI 9.1–10.5) for the pre-fortification period to 4.8 per 10,000 live births (95 % CI 4.3–5.3) for the post–fortification period. Results indicate a statistically significant (P < 0.05) decrease of 51 % in the prevalence of neural tube defects from the pre-fortification period to the post-fortification period. Folic acid fortification via several basic food sources has shown to be a successful public health intervention for Costa Rica. Costa Rica’s experience can serve as an example for other countries seeking to develop and strengthen both their birth defects surveillance and fortification programs. PMID:24952876

Neural tube defects in Costa Rica, 1987-2012: origins and development of birth defect surveillance and folic acid fortification.

PubMed

Barboza-Argüello, María de la Paz; Umaña-Solís, Lila M; Azofeifa, Alejandro; Valencia, Diana; Flores, Alina L; Rodríguez-Aguilar, Sara; Alfaro-Calvo, Thelma; Mulinare, Joseph

2015-03-01

Our aim was to provide a descriptive overview of how the birth defects surveillance and folic acid fortification programs were implemented in Costa Rica-through the establishment of the Registry Center for Congenital Anomalies (Centro de Registro de Enfermedades Congénitas-CREC), and fortification legislation mandates. We estimated the overall prevalence of neural tube defects (i.e., spina bifida, anencephaly and encephalocele) before and after fortification captured by CREC. Prevalence was calculated by dividing the total number of infants born with neural tube defects by the total number of live births in the country (1987-2012).A total of 1,170 newborns with neural tube defects were identified from 1987 to 2012 (1992-1995 data excluded); 628 were identified during the baseline pre-fortification period (1987-1991; 1996-1998); 191 during the fortification period (1999-2002); and 351 during the post-fortification time period (2003-2012). The overall prevalence of neural tube defects decreased from 9.8 per 10,000 live-births (95 % CI 9.1-10.5) for the pre-fortification period to 4.8 per 10,000 live births (95 % CI 4.3-5.3) for the post-fortification period. Results indicate a statistically significant (P < 0.05) decrease of 51 % in the prevalence of neural tube defects from the pre-fortification period to the post-fortification period. Folic acid fortification via several basic food sources has shown to be a successful public health intervention for Costa Rica. Costa Rica's experience can serve as an example for other countries seeking to develop and strengthen both their birth defects surveillance and fortification programs.

Phocomelia: a worldwide descriptive epidemiologic study in a large series of cases from the International Clearinghouse for Birth Defects Surveillance and Research, and overview of the literature.

PubMed

Bermejo-Sánchez, Eva; Cuevas, Lourdes; Amar, Emmanuelle; Bianca, Sebastiano; Bianchi, Fabrizio; Botto, Lorenzo D; Canfield, Mark A; Castilla, Eduardo E; Clementi, Maurizio; Cocchi, Guido; Landau, Danielle; Leoncini, Emanuele; Li, Zhu; Lowry, R Brian; Mastroiacovo, Pierpaolo; Mutchinick, Osvaldo M; Rissmann, Anke; Ritvanen, Annukka; Scarano, Gioacchino; Siffel, Csaba; Szabova, Elena; Martínez-Frías, María-Luisa

2011-11-15

Epidemiologic data on phocomelia are scarce. This study presents an epidemiologic analysis of the largest series of phocomelia cases known to date. Data were provided by 19 birth defect surveillance programs, all members of the International Clearinghouse for Birth Defects Surveillance and Research. Depending on the program, data corresponded to a period from 1968 through 2006. A total of 22,740,933 live births, stillbirths and, for some programs, elective terminations of pregnancy for fetal anomaly (ETOPFA) were monitored. After a detailed review of clinical data, only true phocomelia cases were included. Descriptive data are presented and additional analyses compared isolated cases with those with multiple congenital anomalies (MCA), excluding syndromes. We also briefly compared congenital anomalies associated with nonsyndromic phocomelia with those presented with amelia, another rare severe congenital limb defect. A total of 141 phocomelia cases registered gave an overall total prevalence of 0.62 per 100,000 births (95% confidence interval: 0.52-0.73). Three programs (Australia Victoria, South America ECLAMC, Italy North East) had significantly different prevalence estimates. Most cases (53.2%) had isolated phocomelia, while 9.9% had syndromes. Most nonsyndromic cases were monomelic (55.9%), with an excess of left (64.9%) and upper limb (64.9%) involvement. Most nonsyndromic cases (66.9%) were live births; most isolated cases (57.9%) weighed more than 2,499 g; most MCA (60.7%) weighed less than 2,500 g, and were more likely stillbirths (30.8%) or ETOPFA (15.4%) than isolated cases. The most common associated defects were musculoskeletal, cardiac, and intestinal. Epidemiological differences between phocomelia and amelia highlighted possible differences in their causes. Copyright © 2011 Wiley Periodicals, Inc.

Phocomelia: A Worldwide Descriptive Epidemiologic Study in a Large Series of Cases From the International Clearinghouse for Birth Defects Surveillance and Research, and Overview of the Literature

PubMed Central

Bermejo-Sánchez, Eva; Cuevas, Lourdes; Amar, Emmanuelle; Bianca, Sebastiano; Bianchi, Fabrizio; Botto, Lorenzo D.; Canfield, Mark A.; Castilla, Eduardo E.; Clementi, Maurizio; Cocchi, Guido; Landau, Danielle; Leoncini, Emanuele; Li, Zhu; Lowry, R. Brian; Mastroiacovo, Pierpaolo; Mutchinick, Osvaldo M.; Rissmann, Anke; Ritvanen, Annukka; Scarano, Gioacchino; Siffel, Csaba; Szabova, Elena; Martínez-Frías, María-Luisa

2015-01-01

Epidemiologic data on phocomelia are scarce. This study presents an epidemiologic analysis of the largest series of phocomelia cases known to date. Data were provided by 19 birth defect surveillance programs, all members of the International Clearinghouse for Birth Defects Surveillance and Research. Depending on the program, data corresponded to a period from 1968 through 2006. A total of 22,740,933 live births, stillbirths and, for some programs, elective terminations of pregnancy for fetal anomaly (ETOPFA) were monitored. After a detailed review of clinical data, only true phocomelia cases were included. Descriptive data are presented and additional analyses compared isolated cases with those with multiple congenital anomalies (MCA), excluding syndromes. We also briefly compared congenital anomalies associated with nonsyndromic phocomelia with those presented with amelia, another rare severe congenital limb defect. A total of 141 phocomelia cases registered gave an overall total prevalence of 0.62 per 100,000 births (95% confidence interval: 0.52–0.73). Three programs (Australia Victoria, South America ECLAMC, Italy North East) had significantly different prevalence estimates. Most cases (53.2%) had isolated phocomelia, while 9.9% had syndromes. Most nonsyndromic cases were monomelic (55.9%), with an excess of left (64.9%) and upper limb (64.9%) involvement. Most nonsyndromic cases (66.9%) were live births; most isolated cases (57.9%) weighed more than 2,499 g; most MCA (60.7%) weighed less than 2,500 g, and were more likely stillbirths (30.8%) or ETOPFA (15.4%) than isolated cases. The most common associated defects were musculoskeletal, cardiac, and intestinal. Epidemiological differences between phocomelia and amelia highlighted possible differences in their causes. PMID:22002800

A set-associative, fault-tolerant cache design

NASA Technical Reports Server (NTRS)

Lamet, Dan; Frenzel, James F.

1992-01-01

The design of a defect-tolerant control circuit for a set-associative cache memory is presented. The circuit maintains the stack ordering necessary for implementing the Least Recently Used (LRU) replacement algorithm. A discussion of programming techniques for bypassing defective blocks is included.

How Do Health Care Providers Diagnose Birth Defects?

MedlinePlus

... NICHD Contacts for Funding Information Peer Review Small Business Programs About the Programs NICHD Priorities Funding Opportunities ... Opportunities Grants Process, Policies & Strategies Peer Review Small Business Programs Training & Career Development For Applicants Sample Applications ...

Study of critical defects in ablative heat shield systems for the space shuttle

NASA Technical Reports Server (NTRS)

Miller, C. C.; Rummel, W. D.

1974-01-01

Experimental results are presented for a program conducted to determine the effects of fabrication-induced defects on the performance of an ablative heat shield material. Exposures representing a variety of space shuttle orbiter mission environments-humidity acoustics, hot vacuum and cold vacuum-culuminating in entry heating and transonic acoustics, were simulated on large panels containing intentional defects. Nondestructive methods for detecting the defects, were investigated. The baseline materials were two honeycomb-reinforced low density, silicone ablators, MG-36 and SS-41. Principal manufacturing-induced defects displaying a critical potential included: off-curing of the ablator, extreme low density, undercut (or crushed) honeycomb reinforcements, and poor wet-coating of honeycomb.

Benefit from NASA

NASA Image and Video Library

2004-04-15

Technology derived by NASA for monitoring control gyros in the Skylab program is directly applicable to the problems of fault detection of railroad wheel bearings. Marhsall Space Flight Center's scientists have developed a detection concept based on the fact that bearing defects excite resonant frequency of rolling elements of the bearing as they impact the defect. By detecting resonant frequency and subsequently analyzing the character of this signal, bearing defects may be detected and identified as to source.

Characterizing and Targeting Replication Stress Response Defects in Breast Cancer

DTIC Science & Technology

2015-08-01

1 AD_________________ Award Number: W81XWH-10-1-0558 TITLE: Characterizing and Targeting Replication Stress Response Defects in Breast Cancer ...PRINCIPAL INVESTIGATOR: Shiaw-Yih Lin, Ph.D. CONTRACTING ORGANIZATION: University of Texas M. D. Anderson Cancer Center Houston, TX 77030 REPORT...Response Defects in Breast Cancer 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Betty Diamond 5d. PROJECT NUMBER Chun-Jen Lin, Hui Dai

Defect Detection in Superconducting Radiofrequency Cavity Surface Using C + + and OpenCV

NASA Astrophysics Data System (ADS)

Oswald, Samantha; Thomas Jefferson National Accelerator Facility Collaboration

2014-03-01

Thomas Jefferson National Accelerator Facility (TJNAF) uses superconducting radiofrequency (SRF) cavities to accelerate an electron beam. If theses cavities have a small particle or defect, it can degrade the performance of the cavity. The problem at hand is inspecting the cavity for defects, little bubbles of niobium on the surface of the cavity. Thousands of pictures have to be taken of a single cavity and then looked through to see how many defects were found. A C + + program with Open Source Computer Vision (OpenCV) was constructed to reduce the number of hours searching through the images and finds all the defects. Using this code, the SRF group is now able to use the code to identify defects in on-going tests of SRF cavities. Real time detection is the next step so that instead of taking pictures when looking at the cavity, the camera will detect all the defects.

The effect of simulated altitude on the visual fields of glaucoma patients and the elderly.

DOT National Transportation Integrated Search

1991-01-01

This study tests whether mild hypoxia, that is typically encountered in civilian aircraft, causes temporary visual field defects in elderly persons or temporarily increases pre-existing defects in persons with glaucoma. The central 24-2 program on th...

Eliminating "Hotspots" in Digital Image Processing

NASA Technical Reports Server (NTRS)

Salomon, P. M.

1984-01-01

Signals from defective picture elements rejected. Image processing program for use with charge-coupled device (CCD) or other mosaic imager augmented with algorithm that compensates for common type of electronic defect. Algorithm prevents false interpretation of "hotspots". Used for robotics, image enhancement, image analysis and digital television.

40 CFR 1068.501 - How do I report emission-related defects?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Reporting Defects and... components or systems containing the following components: (i) Electronic control units, aftertreatment... control information labels. Note however, that § 1068.101(a)(1) prohibits the sale of engines/equipment...

Three-dimensional interactive Molecular Dynamics program for the study of defect dynamics in crystals

NASA Astrophysics Data System (ADS)

Patriarca, M.; Kuronen, A.; Robles, M.; Kaski, K.

2007-01-01

The study of crystal defects and the complex processes underlying their formation and time evolution has motivated the development of the program ALINE for interactive molecular dynamics experiments. This program couples a molecular dynamics code to a Graphical User Interface and runs on a UNIX-X11 Window System platform with the MOTIF library, which is contained in many standard Linux releases. ALINE is written in C, thus giving the user the possibility to modify the source code, and, at the same time, provides an effective and user-friendly framework for numerical experiments, in which the main parameters can be interactively varied and the system visualized in various ways. We illustrate the main features of the program through some examples of detection and dynamical tracking of point-defects, linear defects, and planar defects, such as stacking faults in lattice-mismatched heterostructures. Program summaryTitle of program:ALINE Catalogue identifier:ADYJ_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADYJ_v1_0 Program obtainable from: CPC Program Library, Queen University of Belfast, N. Ireland Computer for which the program is designed and others on which it has been tested: Computers:DEC ALPHA 300, Intel i386 compatible computers, G4 Apple Computers Installations:Laboratory of Computational Engineering, Helsinki University of Technology, Helsinki, Finland Operating systems under which the program has been tested:True64 UNIX, Linux-i386, Mac OS X 10.3 and 10.4 Programming language used:Standard C and MOTIF libraries Memory required to execute with typical data:6 Mbytes but may be larger depending on the system size No. of lines in distributed program, including test data, etc.:16 901 No. of bytes in distributed program, including test data, etc.:449 559 Distribution format:tar.gz Nature of physical problem:Some phenomena involving defects take place inside three-dimensional crystals at times which can be hardly predicted. For this reason they are difficult to detect and track even within numerical experiments, especially when one is interested in studying their dynamical properties and time evolution. Furthermore, traditional simulation methods require the storage of a huge amount of data which in turn may imply a long work for their analysis. Method of solution:Simplifications of the simulation work described above strongly depend also on the computer performance. It has now become possible to realize some of such simplifications thanks to the real possibility of using interactive programs. The solution proposed here is based on the development of an interactive graphical simulation program both for avoiding large storage of data and the subsequent elaboration and analysis as well as for visualizing and tracking many phenomena inside three-dimensional samples. However, the full computational power of traditional simulation programs may not be available in general in programs with graphical user interfaces, due to their interactive nature. Nevertheless interactive programs can still be very useful for detecting processes difficult to visualize, restricting the range or making a fine tuning of the parameters, and tailoring the faster programs toward precise targets. Restrictions on the complexity of the problem:The restrictions on the applicability of the program are related to the computer resources available. The graphical interface and interactivity demand computational resources that depend on the particular numerical simulation to be performed. To preserve a balance between speed and resources, the choice of the number of atoms to be simulated is critical. With an average current computer, simulations of systems with more than 10 5 atoms may not be easily feasible on an interactive scheme. Another restriction is related to the fact that the program was originally designed to simulate systems in the solid phase, so that problems in the simulation may occur if some particular physical quantities are computed beyond the melting point. Typical running time:It depends on the machine architecture, system size, and user needs. Unusual features of the program:In the program, besides the window in which the system is represented in real space, an additional graphical window presenting the real time distribution histogram for different physical variables (such as kinetic or potential energy) is included. Such tool is very interesting for making demonstrative numerical experiments for teaching purposes as well as for research, e.g., for detecting and tracking crystal defects. The program includes: an initial condition builder, an interactive display of the simulation, a set of tools which allow the user to filter through different physical quantities the information—either displayed in real time or printed in the output files—and to perform an efficient search of the interesting regions of parameter space.

TV programs that denounce unfair advantage impact women's sensitivity to defection in the public goods game.

PubMed

Park, Seongmin A; Jeong, Soyeong; Jeong, Jaeseung

2013-01-01

We explore the neural underpinnings of gender differences in cooperation and their modulation by intensive media watching. We compared cooperative decisions and electroencephalograph data between genders from who participated in repeated rounds of the public goods game (PGG) and investigated within groups changes that occurred after watching a TV program known as "investigative reporting" that denounces unfair advantages taken by free-riders against the public. Women tended to be more cooperative than men during early rounds of PGG, mostly because they react differently to the defection of others; women also had greater β and γ band activity in regions estimated to be associated with social cognition. These gender differences disappeared after participants watched the TV programs: women were more likely to choose free-riding in response to the defection of others that elicits significant increases in γ band activities that were estimated to be right insula. Greater activity in social cognition leads women to make decisions considering the motives of others, while men tend to make a decision by complying with the social norm. Watching the investigative TV reports produced a greater negative emotion to the defection and led women, in a similar manner as men, to opt for a "tit-for-tat" strategy.

Mating programs including genomic relationships

USDA-ARS?s Scientific Manuscript database

Computer mating programs have helped breeders minimize pedigree inbreeding and avoid recessive defects by mating animals with parents that have fewer common ancestors. With genomic selection, breed associations, AI organizations, and on-farm software providers could use new programs to minimize geno...

AACSD: An atomistic analyzer for crystal structure and defects

NASA Astrophysics Data System (ADS)

Liu, Z. R.; Zhang, R. F.

2018-01-01

We have developed an efficient command-line program named AACSD (Atomistic Analyzer for Crystal Structure and Defects) for the post-analysis of atomic configurations generated by various atomistic simulation codes. The program has implemented not only the traditional filter methods like the excess potential energy (EPE), the centrosymmetry parameter (CSP), the common neighbor analysis (CNA), the common neighborhood parameter (CNP), the bond angle analysis (BAA), and the neighbor distance analysis (NDA), but also the newly developed ones including the modified centrosymmetry parameter (m-CSP), the orientation imaging map (OIM) and the local crystallographic orientation (LCO). The newly proposed OIM and LCO methods have been extended for all three crystal structures including face centered cubic, body centered cubic and hexagonal close packed. More specially, AACSD can be easily used for the atomistic analysis of metallic nanocomposite with each phase to be analyzed independently, which provides a unique pathway to capture their dynamic evolution of various defects on the fly. In this paper, we provide not only a throughout overview on various theoretical methods and their implementation into AACSD program, but some critical evaluations, specific testing and applications, demonstrating the capability of the program on each functionality.

The verification of printability about marginal defects and the detectability at the inspection tool in sub 50nm node

NASA Astrophysics Data System (ADS)

Lee, Hyemi; Jeong, Goomin; Seo, Kangjun; Kim, Sangchul; kim, changreol

2008-05-01

Since mask design rule is smaller and smaller, Defects become one of the issues dropping the mask yield. Furthermore controlled defect size become smaller while masks are manufactured. According to ITRS roadmap on 2007, controlled defect size is 46nm in 57nm node and 36nm in 45nm node on a mask. However the machine development is delayed in contrast with the speed of the photolithography development. Generally mask manufacturing process is divided into 3 parts. First part is patterning on a mask and second part is inspecting the pattern and repairing the defect on the mask. At that time, inspection tools of transmitted light type are normally used and are the most trustful as progressive type in the developed inspection tools until now. Final part is shipping the mask after the qualifying the issue points and weak points. Issue points on a mask are qualified by using the AIMS (Aerial image measurement system). But this system is including the inherent error possibility, which is AIMS measures the issue points based on the inspection results. It means defects printed on a wafer are over the specific size detected by inspection tools and the inspection tool detects the almost defects. Even though there are no tools to detect the 46nm and 36nm defects suggested by ITRS roadmap, this assumption is applied to manufacturing the 57nm and 45nm device. So we make the programmed defect mask consisted with various defect type such as spot, clear extension, dark extension and CD variation on L/S(line and space), C/H(contact hole) and Active pattern in 55nm and 45nm node. And the programmed defect mask was inspected by using the inspection tool of transmitted light type and was measured by using AIMS 45-193i. Then the marginal defects were compared between the inspection tool and AIMS. Accordingly we could verify whether defect size is proper or not, which was suggested to be controlled on a mask by ITRS roadmap. Also this result could suggest appropriate inspection tools for next generation device among the inspection tools of transmitted light type, reflected light type and aerial image type.

Application of data screening to drug exposure in large risk factor studies of birth defects.

PubMed

Louik, Carol; Werler, Martha; Anderka, Marlene; Mitchell, Allen A

2015-08-01

Birth defects are the leading cause of infant death. While causes of most are unknown, those that might be due to medication use are among the most preventable. This study describes an approach to identifying those medications that most warrant attention by using a "screen" program that calculates odds ratios for pairs of exposures and specific birth defects. We discuss the development of this tool and illustrate its application to two large risk factor studies, the Slone Epidemiology Center's Birth Defects Study and the Centers for Disease Control and Prevention's National Birth Defects Prevention Study, ideal settings for the systematic study of risks and relative safety of drugs in relation to birth defects while recognizing the inherent limitations of such an approach. Suggestions for establishing criteria for exposures and outcomes that balance the need for specific details with the practical considerations of sample size and volume of output are presented. Selection of appropriate exposure reference categories and control groups is also discussed, as well as the need to address potential confounding. An example that motivated a detailed investigation of possible associations between a medication (butalbital) and selected specific birth defects is provided. While screening programs such as the one described can be a valuable tool for exploring potential associations in large data bases, they must be applied with caution. The issue of multiple testing and chance findings is a major concern. While statistics are a necessary component, human judgment must be an integral part of the process. © 2015 Wiley Periodicals, Inc.

49 CFR 573.14 - Accelerated remedy program.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Accelerated remedy program. 573.14 Section 573.14... § 573.14 Accelerated remedy program. (a) An accelerated remedy program is one in which the manufacturer expands the sources of replacement parts needed to remedy the defect or noncompliance, or expands the...

49 CFR 573.14 - Accelerated remedy program.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Accelerated remedy program. 573.14 Section 573.14... § 573.14 Accelerated remedy program. (a) An accelerated remedy program is one in which the manufacturer expands the sources of replacement parts needed to remedy the defect or noncompliance, or expands the...

Debugging a high performance computing program

DOEpatents

Gooding, Thomas M.

2014-08-19

Methods, apparatus, and computer program products are disclosed for debugging a high performance computing program by gathering lists of addresses of calling instructions for a plurality of threads of execution of the program, assigning the threads to groups in dependence upon the addresses, and displaying the groups to identify defective threads.

Debugging a high performance computing program

DOEpatents

Gooding, Thomas M.

2013-08-20

Methods, apparatus, and computer program products are disclosed for debugging a high performance computing program by gathering lists of addresses of calling instructions for a plurality of threads of execution of the program, assigning the threads to groups in dependence upon the addresses, and displaying the groups to identify defective threads.

Multiscale Materials Science - A Mathematical Approach to the Role of Defects and Uncertainty

DTIC Science & Technology

2016-10-28

AFRL-AFOSR-UK-TR-2016-0034 Multiscale materials science - a mathematical approach to the role of defects and uncertainty Claude Le Bris ECOLE...science - a mathematical approach to the role of defects and uncertainty 5a.  CONTRACT NUMBER 5b.  GRANT NUMBER FA8655-13-1-3061 5c.  PROGRAM ELEMENT...1FORM SF 298 10/31/2016https://livelink.ebs.afrl.af.mil/livelink/llisapi.dll Contract FA 8655-13-1-3061 Multiscale materials science: a mathematical

Evaluation of anti-sticking layers performances for 200mm wafer scale Smart NILTM process through surface and defectivity characterizations

NASA Astrophysics Data System (ADS)

Delachat, F.; Phillipe, J.-C.; Larrey, V.; Fournel, F.; Bos, S.; Teyssèdre, H.; Chevalier, Xavier; Nicolet, Célia; Navarro, Christophe; Cayrefourcq, Ian

2018-03-01

In this work, an evaluation of various ASL processes for 200 mm wafer scale in the HERCULES® NIL equipment platform available at the CEA-Leti through the INSPIRE program is reported. The surface and adherence energies were correlated to the AFM and defectivity results in order to select the most promising ASL process for high resolution etch mask applications. The ASL performances of the selected process were evaluated by multiple working stamp fabrication using unpatterned and patterned masters though defectivity monitoring on optical based-inspection tools. Optical and SEM defect reviews were systematically performed. Multiple working stamps fabrication without degradation of the master defectivity was witnessed. This evaluation enabled to benchmark several ASL solutions based on the grafted technology develop by ARKEMA in order to reduce and optimize the soft stamp defectivity prior to its replication and therefore considerably reduce the final imprint defectivity for the Smart NIL process.

Mating programs including genomic relationships and dominance effects

USDA-ARS?s Scientific Manuscript database

Computer mating programs have helped breeders minimize pedigree inbreeding and avoid recessive defects by mating animals with parents that have fewer common ancestors. With genomic selection, breed associations, AI organizations, and on-farm software providers could use new programs to minimize geno...

The Correlation Between Dislocations and Vacancy Defects Using Positron Annihilation Spectroscopy

NASA Astrophysics Data System (ADS)

Pang, Jinbiao; Li, Hui; Zhou, Kai; Wang, Zhu

2012-07-01

An analysis program for positron annihilation lifetime spectra is only applicable to isolated defects, but is of no use in the presence of defective correlations. Such limitations have long caused problems for positron researchers in their studies of complicated defective systems. In order to solve this problem, we aim to take a semiconductor material, for example, to achieve a credible average lifetime of single crystal silicon under plastic deformation at different temperatures using positron life time spectroscopy. By establishing reasonable positron trapping models with defective correlations and sorting out four lifetime components with multiple parameters, as well as their respective intensities, information is obtained on the positron trapping centers, such as the positron trapping rates of defects, the density of the dislocation lines and correlation between the dislocation lines, and the vacancy defects, by fitting with the average lifetime with the aid of Matlab software. These results give strong grounds for the existence of dislocation-vacancy correlation in plastically deformed silicon, and lay a theoretical foundation for the analysis of positron lifetime spectra when the positron trapping model involves dislocation-related defects.

Programmed Application of Transforming Growth Factor β3 and Rac1 Inhibitor NSC23766 Committed Hyaline Cartilage Differentiation of Adipose-Derived Stem Cells for Osteochondral Defect Repair.

PubMed

Zhu, Shouan; Chen, Pengfei; Wu, Yan; Xiong, Si; Sun, Heng; Xia, Qingqing; Shi, Libing; Liu, Huanhuan; Ouyang, Hong Wei

2014-10-01

Hyaline cartilage differentiation is always the challenge with application of stem cells for joint repair. Transforming growth factors (TGFs) and bone morphogenetic proteins can initiate cartilage differentiation but often lead to hypertrophy and calcification, related to abnormal Rac1 activity. In this study, we developed a strategy of programmed application of TGFβ3 and Rac1 inhibitor NSC23766 to commit the hyaline cartilage differentiation of adipose-derived stem cells (ADSCs) for joint cartilage repair. ADSCs were isolated and cultured in a micromass and pellet culture model to evaluate chondrogenic and hypertrophic differentiation. The function of Rac1 was investigated with constitutively active Rac1 mutant and dominant negative Rac1 mutant. The efficacy of ADSCs with programmed application of TGFβ3 and Rac1 inhibitor for cartilage repair was studied in a rat model of osteochondral defects. The results showed that TGFβ3 promoted ADSCs chondro-lineage differentiation and that NSC23766 prevented ADSC-derived chondrocytes from hypertrophy in vitro. The combination of ADSCs, TGFβ3, and NSC23766 promoted quality osteochondral defect repair in rats with much less chondrocytes hypertrophy and significantly higher International Cartilage Repair Society macroscopic and microscopic scores. The findings have illustrated that programmed application of TGFβ3 and Rac1 inhibitor NSC23766 can commit ADSCs to chondro-lineage differentiation and improve the efficacy of ADSCs for cartilage defect repair. These findings suggest a promising stem cell-based strategy for articular cartilage repair. ©AlphaMed Press.

Developing a database management system to support birth defects surveillance in Florida.

PubMed

Salemi, Jason L; Hauser, Kimberlea W; Tanner, Jean Paul; Sampat, Diana; Correia, Jane A; Watkins, Sharon M; Kirby, Russell S

2010-01-01

The value of any public health surveillance program is derived from the ways in which data are managed and used to improve the public's health. Although birth defects surveillance programs vary in their case volume, budgets, staff, and objectives, the capacity to operate efficiently and maximize resources remains critical to long-term survival. The development of a fully-integrated relational database management system (DBMS) can enrich a surveillance program's data and improve efficiency. To build upon the Florida Birth Defects Registry--a statewide registry relying solely on linkage of administrative datasets and unconfirmed diagnosis codes-the Florida Department of Health provided funding to the University of South Florida to develop and pilot an enhanced surveillance system in targeted areas with a more comprehensive approach to case identification and diagnosis confirmation. To manage operational and administrative complexities, a DBMS was developed, capable of managing transmission of project data from multiple sources, tracking abstractor time during record reviews, offering tools for defect coding and case classification, and providing reports to DBMS users. Since its inception, the DBMS has been used as part of our surveillance projects to guide the receipt of over 200 case lists and review of 12,924 fetuses and infants (with associated maternal records) suspected of having selected birth defects in over 90 birthing and transfer facilities in Florida. The DBMS has provided both anticipated and unexpected benefits. Automation of the processes for managing incoming case lists has reduced clerical workload considerably, while improving accuracy of working lists for field abstraction. Data quality has improved through more effective use of internal edits and comparisons with values for other data elements, while simultaneously increasing abstractor efficiency in completion of case abstraction. We anticipate continual enhancement to the DBMS in the future. While we have focused on enhancing the capacity of our DBMS for birth defects surveillance, many of the tools and approaches we have developed translate directly to other public health and clinical registries.

Clinical differentiation of patent foramen ovale and secundum atrial septal defect: a survey of pediatric cardiologists in Dallas, Texas, USA.

PubMed

Scheuerle, Angela

2011-01-01

Public health birth defect surveillance registries rely on health care provider diagnosis and definition of congenital anomalies. Major anomalies are likely to have consistent diagnoses across providers; however, definition of some more common, often minor, defects can be problematic. Of particular frustration are the transient neonatal heart findings: patent ductus arteriosus, patent foramen ovale, and pulmonary artery branch stenosis. Under certain circumstances these findings may be considered true anomalies-patent foramen ovale (PFO) as a clinical finding overlaps significantly with atrial septal defect (ASD) of secundum type, the latter being considered a true congenital malformation. Some criteria must be established to separate these conditions in case ascertainment. It is therefore helpful to understand the clinical definitions of patent foramen ovale and secundum atrial septal defect. Pediatric cardiologists in the greater Dallas, Texas metropolitan area were surveyed by telephone, fax, and/or email and asked what criteria they use to distinguish a PFO from a secundum ASD. This was an open-ended question. No baseline parameters were suggested or introduced by the interviewer. Pediatric cardiology fellowship training was identified for each physician to examine the hypothesis that graduates of a given program would use the same diagnostic criteria. Responses were obtained from 22 of 23 pediatric cardiologists. Four measurement criteria were identified: size of the opening, presence or absence of a flap of septal tissue, appearance of the defect on echocardiogram and presence/absence/amount of blood shunting across through the opening. Though there was overlap, diagnostic criteria differentiating PFO and secundum ASD varied among pediatric cardiologists. Two fellowship programs were well represented by the respondent population. Eight respondents were trained at Fellowship 1 and 5 at Fellowship 2. Place of fellowship training was not a strong indicator of which diagnostic criteria were used, even when graduates were in practice together. Physicians in private practice were more likely to report objective measurements as bases for their diagnostic decision. The pronounced variability in clinical definitions will be a problem for birth defect surveillance and research based upon the resultant database. When different physicians use different diagnostic criteria for borderline defects, it is impossible to know whether a defect ascertained and coded with a standard protocol is the same across the population. Since it is unlikely that consistent diagnostic criteria can be put in place, the surveillance program is burdened with compensating for the variability.

CASTING DEFECT MODELING IN AN INTEGRATED COMPUTATIONAL MATERIALS ENGINEERING APPROACH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabau, Adrian S

2015-01-01

To accelerate the introduction of new cast alloys, the simultaneous modeling and simulation of multiphysical phenomena needs to be considered in the design and optimization of mechanical properties of cast components. The required models related to casting defects, such as microporosity and hot tears, are reviewed. Three aluminum alloys are considered A356, 356 and 319. The data on calculated solidification shrinkage is presented and its effects on microporosity levels discussed. Examples are given for predicting microporosity defects and microstructure distribution for a plate casting. Models to predict fatigue life and yield stress are briefly highlighted here for the sake ofmore » completion and to illustrate how the length scales of the microstructure features as well as porosity defects are taken into account for modeling the mechanical properties. Thus, the data on casting defects, including microstructure features, is crucial for evaluating the final performance-related properties of the component. ACKNOWLEDGEMENTS This work was performed under a Cooperative Research and Development Agreement (CRADA) with the Nemak Inc., and Chrysler Co. for the project "High Performance Cast Aluminum Alloys for Next Generation Passenger Vehicle Engines. The author would also like to thank Amit Shyam for reviewing the paper and Andres Rodriguez of Nemak Inc. Research sponsored by the U. S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office, as part of the Propulsion Materials Program under contract DE-AC05-00OR22725 with UT-Battelle, LLC. Part of this research was conducted through the Oak Ridge National Laboratory's High Temperature Materials Laboratory User Program, which is sponsored by the U. S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Program.« less

Elimination of Mental Defect Due to Iodine Deficiency by the Year 2000.

ERIC Educational Resources Information Center

Hetzel, Basil S.

1993-01-01

This paper reviews the effects of iodine deficiency across the lifespan, with special reference to mental defect; discusses the magnitude of the problem; describes available iodine technology to control iodine deficiency disorders (IDD); and notes the status of national IDD control programs, to assess the likelihood of eliminating IDD by the year…

Evaluation of the Effectiveness and Efficiency of Preventive Dentistry Programs: Assessment of the Relationship between Past Dental Experience and Dental Sick Call in the Field

DTIC Science & Technology

1981-09-01

of the emergencies (41.2%) followed by third molar /pericoronitis (15.9%), defective filling or fractured tooth (11.0%), gingival and periodcntal...cause of the emergencies (41.2%J followed by third molar /pericoronitis (15.9%), defective filling or fractured tooth (11.0%), gingival and periodontal...EXERCISES AT FORt IRWIN, CA 1981 CONDITION FREQUENCY PERCENT CARIES 75 41.2 THIRD MOLARS /PERICORONITIS 29 15.9 DEFECTIVE FILLING/FRACTURED TOOTH 20 11.0

The Depth Limits of Eddy Current Testing for Defects: A Computational Investigation and Smooth-Shaped Defect Synthesis from Finite Element Optimization

DTIC Science & Technology

2015-04-22

AND SUBTITLE 5a. CONTRACT NUMBER W56HZV-07-2-0001 W56HZV-08- C - 0236 The Depth Limits of Eddy Current Testing for Defects: A...Unlimited b. ABSTRACT Unlimited c . THIS PAGE Unlimited Unlimited 12 19b. TELEPHONE NUMBER (include area code) 586-282-6471 Standard Form 298...Dave Gunter, Acting Associate Director, Analytics, US Army TARDEC  Dr. Dave Horner, Director, DoD HPC Mod Program  Mr. Steve Knott , Deputy

Phase measurements of EUV mask defects

DOE PAGES

Claus, Rene A.; Wang, Yow-Gwo; Wojdyla, Antoine; ...

2015-02-22

Extreme Ultraviolet (EUV) Lithography mask defects were examined on the actinic mask imaging system, SHARP, at Lawrence Berkeley National Laboratory. Also, a quantitative phase retrieval algorithm based on the Weak Object Transfer Function was applied to the measured through-focus aerial images to examine the amplitude and phase of the defects. The accuracy of the algorithm was demonstrated by comparing the results of measurements using a phase contrast zone plate and a standard zone plate. Using partially coherent illumination to measure frequencies that would otherwise fall outside the numerical aperture (NA), it was shown that some defects are smaller than themore » conventional resolution of the microscope. We found that the programmed defects of various sizes were measured and shown to have both an amplitude and a phase component that the algorithm is able to recover.« less

Defect inspection and printability study for 14 nm node and beyond photomask

NASA Astrophysics Data System (ADS)

Seki, Kazunori; Yonetani, Masashi; Badger, Karen; Dechene, Dan J.; Akima, Shinji

2016-10-01

Two different mask inspection techniques are developed and compared for 14 nm node and beyond photomasks, High resolution and Litho-based inspection. High resolution inspection is the general inspection method in which a 19x nm wavelength laser is used with the High NA inspection optics. Litho-based inspection is a new inspection technology. This inspection uses the wafer lithography information, and as such, this method has automatic defect classification capability which is based on wafer printability. Both High resolution and Litho-based inspection methods are compared using 14 nm and 7 nm node programmed defect and production design masks. The defect sensitivity and mask inspectability is compared, in addition to comparing the defect classification and throughput. Additionally, the Cost / Infrastructure comparison is analyzed and the impact of each inspection method is discussed.

Evaluation of nondestructive testing techniques for the space shuttle nonmetallic thermal protection system

NASA Technical Reports Server (NTRS)

Tiede, D. A.

1972-01-01

A program was conducted to evaluate nondestructive analysis techniques for the detection of defects in rigidized surface insulation (a candidate material for the Space Shuttle thermal protection system). Uncoated, coated, and coated and bonded samples with internal defects (voids, cracks, delaminations, density variations, and moisture content), coating defects (holes, cracks, thickness variations, and loss of adhesion), and bondline defects (voids and unbonds) were inspected by X-ray radiography, acoustic, microwave, high-frequency ultrasonic, beta backscatter, thermal, holographic, and visual techniques. The detectability of each type of defect was determined for each technique (when applicable). A possible relationship between microwave reflection measurements (or X-ray-radiography density measurements) and the tensile strength was established. A possible approach for in-process inspection using a combination of X-ray radiography, acoustic, microwave, and holographic techniques was recommended.

Racial/ethnic variations in the prevalence of selected major birth defects, metropolitan Atlanta, 1994-2005.

PubMed

Kucik, James E; Alverson, Clinton J; Gilboa, Suzanne M; Correa, Adolfo

2012-01-01

Birth defects are the leading cause of infant mortality and are responsible for substantial child and adult morbidity. Documenting the variation in prevalence of birth defects among racial/ethnic subpopulations is critical for assessing possible variations in diagnosis, case ascertainment, or risk factors among such groups. We used data from the Metropolitan Atlanta Congenital Defects Program, a population-based birth defects registry with active case ascertainment. We estimated the racial/ethnic variation in prevalence of 46 selected major birth defects among live births, stillbirths, and pregnancy terminations at >20 weeks gestation among mothers residing in the five central counties of metropolitan Atlanta between 1994 and 2005, adjusting for infant sex, maternal age, gravidity, and socioeconomic status (SES). We also explored SES as a potential effect measure modifier. Compared with births to non-Hispanic white women, births to non-Hispanic black women had a significantly higher prevalence of five birth defects and a significantly lower prevalence of 10 birth defects, while births to Hispanic women had a significantly higher prevalence of four birth defects and a significantly lower prevalence of six birth defects. The racial/ethnic disparities in the prevalence of some defects varied by SES, but no clear pattern emerged. Racial/ethnic disparities were suggested in 57% of included birth defects. Disparities in the prevalence of birth defects may result from different underlying genetic susceptibilities; exposure to risk factors; or variability in case diagnosis, ascertainment, or reporting among the subpopulations examined. Policies that improve early diagnosis of birth defects could reduce associated morbidity and mortality.

Level of Service Program for INDOT Operations : APPENDIX E Activity Defect Assignment

DOT National Transportation Integrated Search

2012-01-01

INDOT has used an inspection program named Maintenance Quality Survey (MQS) to perform a statewide inspection of their roadway assets, rightofway to rightofway. This inspection requires two twoperson teams approximately 18 months to...

Acquired color vision and visual field defects in patients with ocular hypertension and early glaucoma.

PubMed

Papaconstantinou, Dimitris; Georgalas, Ilias; Kalantzis, George; Karmiris, Efthimios; Koutsandrea, Chrysanthi; Diagourtas, Andreas; Ladas, Ioannis; Georgopoulos, Gerasimos

2009-01-01

To study acquired color vision and visual field defects in patients with ocular hypertension (OH) and early glaucoma. In a prospective study we evaluated 99 eyes of 56 patients with OH without visual field defects and no hereditary color deficiencies, followed up for 4 to 6 years (mean = 4.7 +/- 0.6 years). Color vision defects were studied using a special computer program for Farnsworth-Munsell 100 hue test and visual field tests were performed with Humphrey analyzer using program 30-2. Both tests were repeated every six months. In fifty-six eyes, glaucomatous defects were observed during the follow-up period. There was a statistically significant difference in total error score (TES) between eyes that eventually developed glaucoma (157.89 +/- 31.79) and OH eyes (75.51 +/- 31.57) at the first examination (t value 12.816, p < 0.001). At the same time visual field indices were within normal limits in both groups. In the glaucomatous eyes the earliest statistical significant change in TES was identified at the first year of follow-up and was -20.62 +/- 2.75 (t value 9.08, p < 0.001) while in OH eyes was -2.11 +/- 4.36 (t value 1.1, p = 0.276). Pearson's coefficient was high in all examinations and showed a direct correlation between TES and mean deviation and corrected pattern standard deviation in both groups. Quantitative analysis of color vision defects provides the possibility of follow-up and can prove a useful means for detecting early glaucomatous changes in patients with normal visual fields.

West Virginia yellow-poplar lumber defect database

Treesearch

Lawrence E. Osborn; Charles J. Gatchell; Curt C. Hassler; Curt C. Hassler

1992-01-01

Describes the data collection methods and the format of the new West Virginia yellow-poplar lumber defect database that was developed for use with computer simulation programs. The database contains descriptions of 627 boards, totaling approximately 3,800 board. feet, collected in West Virginia in grades FAS, FASlF, No. 1 Common, No. 2A Common, and No. 2B Common. The...

Actinic inspection of EUV reticles with arbitrary pattern design

NASA Astrophysics Data System (ADS)

Mochi, Iacopo; Helfenstein, Patrick; Rajeev, Rajendran; Fernandez, Sara; Kazazis, Dimitrios; Yoshitake, Shusuke; Ekinci, Yasin

2017-10-01

The re ective-mode EUV mask scanning lensless imaging microscope (RESCAN) is being developed to provide actinic mask inspection capabilities for defects and patterns with high resolution and high throughput, for 7 nm node and beyond. Here we, will report on our progress and present the results on programmed defect detection on random, logic-like patterns. The defects we investigated range from 200 nm to 50 nm size on the mask. We demonstrated the ability of RESCAN to detect these defects in die-to-die and die-to-database mode with a high signal to noise ratio. We also describe future plans for the upgrades to increase the resolution, the sensitivity, and the inspection speed of the demo tool.

Computer simulation of electrical characteristics of singlewalled carbon nanotube (9,0) with Stone-Wales defect

NASA Astrophysics Data System (ADS)

Sergeyev, D.; Zhanturina, N.

2018-05-01

In the framework of the density functional theory, using the method of nonequilibrium Green's functions and in the local density approximation, the electrical characteristics of different configurations of a single-walled carbon nanotube with Stone-Wales defects are investigated. The calculation is implemented in the Atomistix ToolKit with Virtual NanoLab program. The current-voltage, dI/dV-characteristics and the density of states of the nanostructures under consideration were calculated. It is shown that the nature of the current flowing through defective carbon nanotubes depends on the extent of the Stone-Wales defects. It was found that a carbon nanotube with two consecutively connected Stone-Wales defects at a bias voltage of ± 2.6 V has a negative differential conductivity of -170 μS. The obtained results can be useful for calculations of new promising electronic devices of nanoelectronics based on a carbon nanotube.

Development Of Ultrasonic Testing Based On Delphi Program As A Learning Media In The Welding Material Study Of Detection And Welding Disables In The Environment Of Vocational Education

NASA Astrophysics Data System (ADS)

Dwi Cahyono, Bagus; Ainur, Chandra

2018-04-01

The development of science and technology has a direct impact on the preparation of qualified workers, including the preparation of vocational high school graduates. Law Number 20 the Year 2003 on National Education System explains that the purpose of vocational education is to prepare learners to be ready to work in certain fields. One of the learning materials in Vocational High School is welding and detecting welding defects. Introduction of welding and detecting welding defects, one way that can be done is by ultrasonic testing will be very difficult if only capitalize the book only. Therefore this study aims to adopt ultrasonic testing in a computer system. This system is called Delphi Program-based Ultrasonic Testing Expert System. This system is used to determine the classification and type of welding defects of the welded defect indicator knew. In addition to the system, there is a brief explanation of the notion of ultrasonic testing, calibration procedures and inspection procedures ultrasonic testing. In this system, ultrasonic input data testing that shows defects entered into the computer manually. This system is built using Delphi 7 software and Into Set Up Compiler as an installer. The method used in this research is Research and Development (R & D), with the following stages: (1) preliminary research; (2) manufacture of software design; (3) materials collection; (4) early product development; (5) validation of instructional media experts; (6) product analysis and revision; (8) media trials in learning; And (9) result of end product of instructional media. The result of the research shows that: (1) the result of feasibility test according to ultrasonic material testing expert that the system is feasible to be used as instructional media in welding material subject and welding defect detection in vocational education environment, because it contains an explanation about detection method of welding defect using method Ultrasonic testing in detail; (2) feasibility test results according to media experts, that this system has a very attractive visual, user friendly, compatible with windows and Linux and media size that is not too large; And (3) result of test by using data of indication of welding defect in PT PAL Surabaya, obtained classification data of welding defect in accordance with calculation of welding defect classification.

Moral Relativism on the Ropes.

ERIC Educational Resources Information Center

Gabler, Mel; Gabler, Norma

1987-01-01

Finds that most current public school sex education programs and all values clarification programs are based on moral relativism and are intellectually indefensible because they are (1) methodologically defective, (2) present tautologies instead of values, (3) depend on circular reasoning, and (4) undemocratic. (NKA)

Use of Family History Information for Neural Tube Defect Prevention: Integration into State-Based Recurrence Prevention Programs

ERIC Educational Resources Information Center

Green, Ridgely Fisk; Ehrhardt, Joan; Ruttenber, Margaret F.; Olney, Richard S.

2011-01-01

A family history of neural tube defects (NTDs) can increase the risk of a pregnancy affected by an NTD. Periconceptional folic acid use decreases this risk. Purpose: Our objective was to determine whether second-degree relatives of NTD-affected children showed differences in folic acid use compared with the general population and to provide them…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skupov, A. V., E-mail: skav10@mail.ru

TRISQD software is developed for the computer simulation of processes in which radiation defects are formed under the corpuscular irradiation of semiconductor heterostructures with lenticular nanoinclusions of various shapes. The computer program is used to study defect-formation processes in p-i-n diodes with the i region having a built-in 20-period lattice of self-assembled Ge(Si) nanoislands formed under irradiation with high-energy neutrons. It is found that the fraction of Ge(Si) nanoislands in which point radiation defects are formed under the impact of atomic-displacement cascades is ≤3% of their total number in the lattice. More than 94% of the defects are localized inmore » the bulk of the p, n, and i regions of the diode and in silicon layers that separate sheets of Ge(Si) nanoislands.« less

Is Bendectin a teratogen?

PubMed

Cordero, J F; Oakley, G P; Greenberg, F; James, L M

1981-06-12

We studied the first-trimester exposure to Bendectin for several major categories of birth defects among infants ascertained through the Metropolitan Atlanta Congenital Defects Program from 1968 to 1978. No associations were found between any of these defect categories and Bendectin exposure. An association, however, was found for the amniotic bands cases--a subgroup of limb reductions. We stratified our data to reflect the 1976 change in formulation when one of the three ingredients was removed. An association was found between esophageal atresia and the three-ingredient product and another between encephalocele and the two ingredient product. These statistical associations do not establish a causal relationship between Bendectin and the birth defects we studied. Furthermore, even if the associations are causal, the implied risk is extremely low, approximately one in 1,000 births.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claus, Rene A.; Wang, Yow-Gwo; Wojdyla, Antoine

Extreme Ultraviolet (EUV) Lithography mask defects were examined on the actinic mask imaging system, SHARP, at Lawrence Berkeley National Laboratory. Also, a quantitative phase retrieval algorithm based on the Weak Object Transfer Function was applied to the measured through-focus aerial images to examine the amplitude and phase of the defects. The accuracy of the algorithm was demonstrated by comparing the results of measurements using a phase contrast zone plate and a standard zone plate. Using partially coherent illumination to measure frequencies that would otherwise fall outside the numerical aperture (NA), it was shown that some defects are smaller than themore » conventional resolution of the microscope. We found that the programmed defects of various sizes were measured and shown to have both an amplitude and a phase component that the algorithm is able to recover.« less

Simple intrinsic defects in GaP and InP

NASA Astrophysics Data System (ADS)

Schultz, Peter A.

2012-02-01

To faithfully simulate evolution of defect chemistry and electrical response in irradiated semiconductor devices requires accurate defect reaction energies and energy levels. In III-Vs, good data is scarce, theory hampered by band gap and supercell problems. I apply density functional theory (DFT) to intrinsic defects in GaP and InP, predicting stable charge states, ground state configurations, defect energy levels, and identifying mobile species. The SeqQuest calculations incorporate rigorous charge boundary conditions removing supercell artifacts, demonstrated converged to the infinite limit. Computed defect levels are not limited by a band gap problem, despite Kohn-Sham gaps much smaller than the experimental gap. As in GaAs, [P.A. Schultz and O.A. von Lilienfeld, Modeling Simul. Mater. Sci. Eng. 17, 084007 (2009)], defects in GaP and InP exhibit great complexity---multitudes of charge states, bistabilities, and negative U systems---but show similarities to each other (and to GaAs). Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Basic research for the geodynamics program

NASA Technical Reports Server (NTRS)

1991-01-01

The mathematical models of space very long base interferometry (VLBI) observables suitable for least squares covariance analysis were derived and estimatability problems inherent in the space VLBI system were explored, including a detailed rank defect analysis and sensitivity analysis. An important aim is to carry out a comparative analysis of the mathematical models of the ground-based VLBI and space VLBI observables in order to describe the background in detail. Computer programs were developed in order to check the relations, assess errors, and analyze sensitivity. In order to investigate the estimatability of different geodetic and geodynamic parameters from the space VLBI observables, the mathematical models for time delay and time delay rate observables of space VLBI were analytically derived along with the partial derivatives with respect to the parameters. Rank defect analysis was carried out both by analytical and numerical testing of linear dependencies between the columns of the normal matrix thus formed. Definite conclusions were formed about the rank defects in the system.

Acquired color vision and visual field defects in patients with ocular hypertension and early glaucoma

PubMed Central

Papaconstantinou, Dimitris; Georgalas, Ilias; Kalantzis, George; Karmiris, Efthimios; Koutsandrea, Chrysanthi; Diagourtas, Andreas; Ladas, Ioannis; Georgopoulos, Gerasimos

2009-01-01

Purpose: To study acquired color vision and visual field defects in patients with ocular hypertension (OH) and early glaucoma. Methods: In a prospective study we evaluated 99 eyes of 56 patients with OH without visual field defects and no hereditary color deficiencies, followed up for 4 to 6 years (mean = 4.7 ± 0.6 years). Color vision defects were studied using a special computer program for Farnsworth–Munsell 100 hue test and visual field tests were performed with Humphrey analyzer using program 30–2. Both tests were repeated every six months. Results: In fifty-six eyes, glaucomatous defects were observed during the follow-up period. There was a statistically significant difference in total error score (TES) between eyes that eventually developed glaucoma (157.89 ± 31.79) and OH eyes (75.51 ± 31.57) at the first examination (t value 12.816, p < 0.001). At the same time visual field indices were within normal limits in both groups. In the glaucomatous eyes the earliest statistical significant change in TES was identified at the first year of follow-up and was −20.62 ± 2.75 (t value 9.08, p < 0.001) while in OH eyes was −2.11 ± 4.36 (t value 1.1, p = 0.276). Pearson’s coefficient was high in all examinations and showed a direct correlation between TES and mean deviation and corrected pattern standard deviation in both groups. Conclusion: Quantitative analysis of color vision defects provides the possibility of follow-up and can prove a useful means for detecting early glaucomatous changes in patients with normal visual fields. PMID:19668575

Area of ischemia assessed by physicians and software packages from myocardial perfusion scintigrams

PubMed Central

2014-01-01

Background The European Society of Cardiology recommends that patients with >10% area of ischemia should receive revascularization. We investigated inter-observer variability for the extent of ischemic defects reported by different physicians and by different software tools, and if inter-observer variability was reduced when the physicians were provided with a computerized suggestion of the defects. Methods Twenty-five myocardial perfusion single photon emission computed tomography (SPECT) patients who were regarded as ischemic according to the final report were included. Eleven physicians in nuclear medicine delineated the extent of the ischemic defects. After at least two weeks, they delineated the defects again, and were this time provided a suggestion of the defect delineation by EXINI HeartTM (EXINI). Summed difference scores and ischemic extent values were obtained from four software programs. Results The median extent values obtained from the 11 physicians varied between 8% and 34%, and between 9% and 16% for the software programs. For all 25 patients, mean extent obtained from EXINI was 17.0% (± standard deviation (SD) 14.6%). Mean extent for physicians was 22.6% (± 15.6%) for the first delineation and 19.1% (± 14.9%) for the evaluation where they were provided computerized suggestion. Intra-class correlation (ICC) increased from 0.56 (95% confidence interval (CI) 0.41-0.72) to 0.81 (95% CI 0.71-0.90) between the first and the second delineation, and SD between physicians were 7.8 (first) and 5.9 (second delineation). Conclusions There was large variability in the estimated ischemic defect size obtained both from different physicians and from different software packages. When the physicians were provided with a suggested delineation, the inter-observer variability decreased significantly. PMID:24479846

The Scientific Stature of Counseling Psychology Training Programs: A Still Picture of a Shifting Scene.

ERIC Educational Resources Information Center

Hanish, Christine; And Others

1995-01-01

Previous attempts to rank doctoral programs in counseling psychology suffered from methodological flaws, such as the "Matthew effect." To offset such defects, this study examines citations in two data bases for 488 counseling psychology faculty. The authors list leading programs on the basis of 11 adjusted and unadjusted measures of scientific…

Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

NASA Astrophysics Data System (ADS)

Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

2015-10-01

Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

Collection, use, and protection of population-based birth defects surveillance data in the united states.

PubMed

Mai, Cara T; Law, David J; Mason, Craig A; McDowell, Bradley D; Meyer, Robert E; Musa, Debra

2007-12-01

Birth defects surveillance systems collect population-based birth defects data from multiple sources to track trends in prevalence, identify risk factors, refer affected families to services, and evaluate prevention efforts. Strong state and federal public health and legal mandates are in place to govern the collection and use of these data. Despite the prima facie appeal of "opt-in" and similar strategies to those who view data collection as a threat to privacy, the use of these strategies in lieu of population-based surveillance can severely limit the ability of public health agencies to accurately access the health status of a group within a defined geographical area. With the need for population-based data central to their mission, birth defects programs around the country take their data stewardship role seriously, recognizing both moral and legal obligations to protect the data by employing numerous safeguards. Birth defects surveillance systems are shaped by the needs of the community they are designed to serve, with the goal of preventing birth defects or alleviating the burdens associated with them. (c) 2007 Wiley-Liss, Inc.

Stability of concentration-related self-interstitial atoms in fusion material tungsten

NASA Astrophysics Data System (ADS)

Hong, Zhang; Shu-Long, Wen; Min, Pan; Zheng, Huang; Yong, Zhao; Xiang, Liu; Ji-Ming, Chen

2016-05-01

Based on the density functional theory, we calculated the structures of the two main possible self-interstitial atoms (SIAs) as well as the migration energy of tungsten (W) atoms. It was found that the difference of the <110> and <111> formation energies is 0.05-0.3 eV. Further analysis indicated that the stability of SIAs is closely related to the concentration of the defect. When the concentration of the point defect is high, <110> SIAs are more likely to exist, <111> SIAs are the opposite. In addition, the vacancy migration probability and self-recovery zones for these SIAs were researched by making a detailed comparison. The calculation provided a new viewpoint about the stability of point defects for self-interstitial configurations and would benefit the understanding of the control mechanism of defect behavior for this novel fusion material. Project supported by the Fundamental Research Funds for the Central Universities of Ministry of Education of China (Grant Nos. A0920502051411-5 and 2682014ZT30), the Program of International Science and Technology Cooperation, China (Grant No. 2013DFA51050), the National Magnetic Confinement Fusion Science Program, China (Grant Nos. 2011GB112001 and 2013GB110001), the National High Technology Research and Development Program of China (Grant No. 2014AA032701), the National Natural Science Foundation of China (Grant No. 11405138), the Southwestern Institute of Physics Funds, China, the Western Superconducting Technologies Company Limited, China, the Qingmiao Plan of Southwest Jiaotong University, China (Grant No. A0920502051517-6), and the China Postdoctoral Science Foundation (Grant No. 2014M560813).

Identifying environmental risk factors for human neural tube defects before and after folic acid supplementation

PubMed Central

Liao, Yilan; Wang, Jinfeng; Li, Xinhu; Guo, Yaoqin; Zheng, Xiaoying

2009-01-01

Background Birth defects are a major cause of infant mortality and disability in many parts of the world. Neural tube defects (NTDs) are one of the most common types of birth defects. In 2001, the Chinese population and family planning commission initiated a national intervention program for the prevention of birth defects. A key step in the program was the introduction of folic acid supplementation. Of interest in the present study was to determine whether folic acid supplementation has the same protective effect on NTDs under various geographical and socioeconomic conditions within the Chinese population and the nature in which the influence of environmental factors varied after folic acid supplementation. Methods In this study, Heshun was selected as the region of interest as a surrogate for helping to answer some of the questions raised in this study on the impact of the intervention program. Spatial filtering in combination with GIS software was used to detect annual potential clusters from 1998 to 2005 in Heshun, and Kruskal-wallis test and multivariate regression were applied to identify the environmental risk factors for NTDs among various regions. Results In 1998, a significant (p < 0.100) NTDs cluster was detected in the west of Heshun. After folic acid supplementation, the significant clusters gradually moved from west to east. However, during the study period, most of the clusters appeared in the middle region of Heshun where more than 95 percent of the coal mines of Heshun are located. For the analysis, buffer regions of the coal mine zone were built in a GIS environment. It was found that the correlations between environmental risk factors and NTDs vary among the buffer regions. Conclusion This suggests that the government needs to adapt the intervention measures according to local conditions. More attention needs to be paid to the poor and to people living in areas near coal mines. PMID:19835574

Fetal programming of appetite and obesity.

PubMed

Breier, B H; Vickers, M H; Ikenasio, B A; Chan, K Y; Wong, W P

2001-12-20

Obesity and related metabolic disorders are prevalent health issues in modern society and are commonly attributed to lifestyle and dietary factors. However, the mechanisms by which environmental factors modulate the physiological systems that control weight regulation and the aetiology of metabolic disorders, which manifest in adult life, may have their roots before birth. The 'fetal origins' or 'fetal programming' paradigm is based on the observation that environmental changes can reset the developmental path during intrauterine development leading to obesity and cardiovascular and metabolic disorders later in life. The pathogenesis is not based on genetic defects but on altered genetic expression as a consequence of an adaptation to environmental changes during fetal development. While many endocrine systems can be affected by fetal programming recent experimental studies suggest that leptin and insulin resistance are critical endocrine defects in the pathogenesis of programming-induced obesity and metabolic disorders. However, it remains to be determined whether postnatal obesity is a consequence of programming of appetite regulation and whether hyperphagia is the main underlying cause of the increased adiposity and the development of metabolic disorders.

Quantum metrology with a single spin-3/2 defect in silicon carbide

NASA Astrophysics Data System (ADS)

Soykal, Oney O.; Reinecke, Thomas L.

We show that implementations for quantum sensing with exceptional sensitivity and spatial resolution can be made using the novel features of semiconductor high half-spin multiplet defects with easy-to-implement optical detection protocols. To achieve this, we use the spin- 3 / 2 silicon monovacancy deep center in hexagonal silicon carbide based on our rigorous derivation of this defect's ground state and of its electronic and optical properties. For a single VSi- defect, we obtain magnetic field sensitivities capable of detecting individual nuclear magnetic moments. We also show that its zero-field splitting has an exceptional strain and temperature sensitivity within the technologically desirable near-infrared window of biological systems. Other point defects, i.e. 3d transition metal or rare-earth impurities in semiconductors, may also provide similar opportunities in quantum sensing due to their similar high spin (S >= 3 / 2) configurations. This work was supported in part by ONR and by the Office of Secretary of Defense, Quantum Science and Engineering Program.

Printability of 1 x reticle defects for submicron design rules

NASA Astrophysics Data System (ADS)

Schurz, Dan L.; Flack, Warren W.; Newman, Gary

1997-02-01

As the push for improved resolution in wafer lithography intensifies and 0.18 micrometer devices are nearing production, the potential impact of subhalf micron reticle defects has become a growing concern. There have been several studies on the printability of subhalf-micron defects on high resolution reduction photolithography equipment. These studies have been extended to 1X lithography systems and more recently to advanced sub-micron 1X steppers. Previous studies have indicated that 0.20 micrometer opaque and 0.25 micrometer clear pinhole defects were at the margins of adversely impacting 0.65 micrometer lithography on a 1X stepper. However, due to the limited number of defects at these sizes on the reticle, definitive conclusions on printability could not be drawn. An additional study, using a three dimensional (3D) optical lithography simulation program, has shown defect size, proximity to an adjacent feature, and feature pitch to be significant factors contributing to reticle defect printability. Using the simulation findings as a guide, a new reticle was designed to contain an increased number of clear pinhole and opaque defects in the 0.15 to 0.30 micrometer range located in multiple pitches of both horizontal and vertical line/space pairs. Defect printability was determined using a 1X i-line projection stepper with focus and exposure optimized for nominal critical dimensions of 0.65 micrometer. The reticle and wafer defects were measured using low voltage SEM metrology. Simulation and experimental results have shown that pitch is the most significant contributor in the printability of clear pinhole, opaque, square and aspect ratio defects. In general, the impact of defect proximity to an adjacent feature is less extreme than the effect of pitch, but is more pronounced for clear pinhole defects. This study suggests that simulation can be a useful tool to help lithographers understand the behavior of reticle defects for particular layout design parameters. Consequently, simulation can be used to develop realistic reticle defect specifications with mask vendors, and improve cost-effectiveness. Defect printability simulation can also be used to predict the effect of known defects on existing reticles to determine if these reticles should be used for manufacturing.

Defect Proliferation in Active Nematic Suspensions

NASA Astrophysics Data System (ADS)

Mishra, Prashant; Bowick, Mark J.; Giomi, Luca; Marchetti, M. Cristina

2014-03-01

The rich structure of equilibrium nematic suspensions, with their characteristic disclination defects, is modified when active forces come into play. The uniform nematic state is known to be unstable to splay (extensile) or bend (contractile) deformations above a critical activity. At even higher activity the flow becomes oscillatory and eventually turbulent. Using hydrodynamics, we classify the active flow regimes as functions of activity and order parameter friction for both contractile and extensile systems. The turbulent regime is marked by a non-zero steady state density of mobile defect pairs. The defect density itself scales with an ``active Ericksen number,'' defined as the ratio of the rate at which activity is injected into the system to the relaxation rate of orientational deformations. The work at Syracuse University was supported by the NSF on grant DMR-1004789 and by the Syracuse Soft Matter Program.

NASA Small Business Innovation Research program

NASA Technical Reports Server (NTRS)

Johnson, Harry W.

1985-01-01

NASA activities in the framework of the 11-agency federal Small Business Innovation Research program are outlined in tables and graphs and briefly characterized. Statistics on the program are given; the technical topics covered are listed; and the procedures involved in evaluating applications for support are discussed. A number of typical defects in proposals are indicated, and recommendations for avoiding them are provided.

ALPS yield optimization cutting program

Treesearch

P. Klinkhachorn; J.P. Franklin; Charles W. McMillin; H.A. Huber

1989-01-01

This paper reports ongoing work on a series of computer programs developed to automate hardwood lumber processing in a furniture roughmill. The program computes the placement of cuttings on lumber, based on a description of each board in terms of shape and defect location, and a cutting bill. These results are suitable for use with a high-power laser to cut the parts...

Prenatal Care Training.

ERIC Educational Resources Information Center

Hagen, Michael

Described is the development and evaluation of a prenatal instructional program designed to prevent birth defects. It is explained that the program, composed of five slide tape units on such topics as nutrition and environmental factors, was field tested and found effective with 97 participants (pregnant high school students, nursing students, and…

Developmental Programming: Postnatal Estradiol Modulation of Prenatally Organized Reproductive Neuroendocrine Function in Sheep

PubMed Central

Puttabyatappa, Muraly; Cardoso, Rodolfo C.; Herkimer, Carol; Veiga-Lopez, Almudena; Padmanabhan, Vasantha

2016-01-01

Gestational testosterone (T) excess, acting via both the androgenic and estrogenic pathways, advances puberty and disrupts the neuroendocrine estradiol (E) feedback and periovulatory hormonal dynamics in female sheep. These prenatally programmed defects may be subject to postnatal modifications by continued organizational and/or activational effects of steroids. The present study investigated 1) the organizational contribution of prenatal estrogen excess and 2) the impact of postnatal exposure to E in modulating the effects of prenatal androgen excess (T and dihydrotestosterone [DHT]) on puberty, neuroendocrine feedback mechanisms, and periovulatory hormonal dynamics in sheep. Pregnant Suffolk sheep were treated with T, DHT, E, or E plus DHT (ED) from days 30 to 90 of gestation. A subset of the control (C), T, and DHT female offspring received a constant-release E implant postnatally. Findings revealed that 1) prenatal E-treatment failed to reproduce the neuroendocrine disruptions predicted to be programmed by the estrogenic pathway and 2) prenatal ED-treatment did not adequately replicate the reproductive neuroendocrine defects induced by prenatal T excess. More importantly, continuous postnatal E-treatment, while delaying the onset of puberty and reducing the inhibitory effects of E on tonic luteinizing hormone (LH) release, failed to amplify the E positive feedback and periovulatory defects induced by prenatal T-treatment. Our results indicate that disruptions in E positive feedback mechanisms and periovulatory gonadotropin secretion induced by prenatal T-treatment are programmed predominantly during the prenatal life with postnatal exposure to E excess not contributing further to these disruptions. PMID:27222598

Alternating phase-shifting masks: phase determination and impact of quartz defects--theoretical and experimental results

NASA Astrophysics Data System (ADS)

Griesinger, Uwe A.; Dettmann, Wolfgang; Hennig, Mario; Heumann, Jan P.; Koehle, Roderick; Ludwig, Ralf; Verbeek, Martin; Zarrabian, Mardjan

2002-07-01

In optical lithography balancing the aerial image of an alternating phase shifting mask (alt. PSM) is a major challenge. For the exposure wavelengths (currently 248nm and 193nm) an optimum etching method is necessary to overcome imbalance effects. Defects play an important role in the imbalances of the aerial image. In this contribution defects will be discussed by using the methodology of global phase imbalance control also for local imbalances which are a result of quartz defects. The effective phase error can be determined with an AIMS-system by measuring the CD width between the images of deep- and shallow trenches at different focus settings. The AIMS results are analyzed in comparison to the simulated and lithographic print results of the alternating structures. For the analysis of local aerial image imbalances it is necessary to investigate the capability of detecting these phase defects with state of the art inspection systems. Alternating PSMs containing programmed defects were inspected with different algorithms to investigate the capture rate of special phase defects in dependence on the defect size. Besides inspection also repair of phase defects is an important task. In this contribution we show the effect of repair on the optical behavior of phase defects. Due to the limited accuracy of the repair tools the repaired area still shows a certain local phase error. This error can be caused either by residual quartz material or a substrate damage. The influence of such repair induced phase errors on the aerial image were investigated.

Magnetic resonance imaging study of eye congenital birth defects in mouse model

PubMed Central

Tucker, Zachary; Mongan, Maureen; Meng, Qinghang; Xia, Ying

2017-01-01

Purpose Embryonic eyelid closure is a well-documented morphogenetic episode in mammalian eye development. Detection of eyelid closure defect in humans is a major challenge because eyelid closure and reopen occur entirely in utero. As a consequence, congenital eye defects that are associated with failure of embryonic eyelid closure remain unknown. To fill the gap, we developed a mouse model of defective eyelid closure. This preliminary work demonstrates that the magnetic resonance imaging (MRI) approach can be used for the detection of extraocular muscle abnormalities in the mouse model. Methods Mice with either normal (Map3k1+/−) or defective (Map3k1−/−) embryonic eyelid closure were used in this study. Images of the extraocular muscles were obtained with a 9.4 T high resolution microimaging MRI system. The extraocular muscles were identified, segmented, and measured in each imaging slice using an in-house program. Results In agreement with histological findings, the imaging data show that mice with defective embryonic eyelid closure develop less extraocular muscle than normal mice. In addition, the size of the eyeballs was noticeably reduced in mice with defective embryonic eyelid closure. Conclusions We demonstrated that MRI can potentially be used for the study of extraocular muscle in the mouse model of the eye open-at-birth defect, despite the lack of specificity of muscle group provided by the current imaging resolution. PMID:28848319

RADC (Rome Air Development Center) Guide to Environmental Stress Screening

DTIC Science & Technology

1986-08-01

and the processes which are used in their manufacture. ESS is the vehicle by which latent defects are accelerated to early failure in the factory. ESS...structured as part of a production 2 reliability assurance program, is the vehicle through which product reliability in manufacture can be maintained...mechanical, electrical and/or thermal stresses to an equipment item for the purpose of precipitating latent part and workmanship defects to early failure

Littoral Combat Ship and Frigate: Slowing Planned Frigate Acquisition Would Enable Better Informed Decisions

DTIC Science & Technology

2016-12-08

States Government Accountability Office United States Government Accountability Office Highlights of GAO-17-279T, a testimony before the...million in defects for each ship. Time will tell whether this amount is sufficient to account for discovered defects.6 Turning to cost and schedule...279T Year GAO recommendation DOD response 2010 • Update the LCS acquisition strategy to account for operational testing delays in the program

Formation of social and household skills in children with hand defects.

PubMed

Klimon, Nataly; Koryukov, Alexander; Loseva, Nina; Starobina, Elena

2015-08-01

The aim of this study was to consider the peculiarities of forming social and household skills, and the criteria for their evaluation, as well as an assessment of functional capacity, in children with hand defects both before and after surgical treatment and rehabilitation courses using a system of games. We elaborated and implemented a program of social rehabilitation of preschool children with congenital and acquired hand defects for the development of their functional capabilities and the formation of social and household skills after surgical treatment and prosthetics using play therapy methods. As part of this work, 140 preschool children aged 3-7 years underwent social rehabilitation. Most of the children had congenital hand defects-122 children (87 %): 96 children (79 %) with ectrodactylia, adactylia, hypoplasia, aplasia, hand splitting, club hand, or partial gigantism; 26 children (21 %) with congenital syndactylism and constricted bonds and 18 children (13 %) with acquired defects (burn deformity, amputation). 110 children (79 %) had reached the stage of surgical correction; 30 children (21 %) reached the stage of prosthetics. Most of the children participating in the experiment (78 children, 56 %) had defects of fingers on one hand. The program aimed at solving specific rehabilitation tasks: formation and improvement of all possible types of grip under the existing defect including those after surgery and prosthetics; development of tactile sensations in fingers; development of fine motor skills; increase in range of motion in all joints of the damaged hand; development of attention and concentration; formation of social and household skills appropriate to age; and development of the ability to achieve the set task. Analysis of the level of social and household skills of children with hand defects undergoing rehabilitation treatment at the hospital depending on the age prior to medical and social rehabilitation showed that preschool children with hand defects in the age category of 3 years demonstrated the highest results in the level of social and household skills (31 %) as compared with children in other age categories. The indicators for children aged 4 and 5 years were slightly lower, 25 and 26 %, respectively. The lowest values were recorded among children aged 6: 20 %. Statistically significant parameters of the level of functional capacity of hand grip and social and household skills in children with hand defects obtained in the course of the investigation indicated that the use of play therapy measures significantly increased the effect of medical treatment irrespective of the type of defect. These data indicate that play therapy measures given immediately after surgery or prosthetics can significantly increase the efficiency of rehabilitation even in its early stages.

Density Functional Theory Calculations of Activation Energies for Carrier Capture by Defects in Semiconductors

NASA Astrophysics Data System (ADS)

Modine, Normand; Wright, Alan; Lee, Stephen

2015-03-01

Carrier recombination due to defects can have a major impact on device performance. The rate of defect-induced recombination is determined by both defect levels and carrier capture cross-sections. Density functional theory (DFT) has been widely and successfully used to predict defect levels, but only recently has work begun to focus on using DFT to determine carrier capture cross-sections. Lang and Henry worked out the fundamental theory of carrier-capture by multiphonon emission in the 1970s and showed that, above the Debye temperature, carrier-capture cross-sections differ between defects primarily due to differences in their carrier capture activation energies. We present an approach to using DFT to calculate carrier capture activation energies that does not depend on an assumed configuration coordinate and that fully accounts for anharmonic effects, which can substantially modify carrier activation energies. We demonstrate our approach for the -3/-2 level of the Ga vacancy in wurtzite GaN. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Density Functional Theory Calculations of Activation Energies for Carrier Capture by Defects in Semiconductors

NASA Astrophysics Data System (ADS)

Modine, N. A.; Wright, A. F.; Lee, S. R.

The rate of defect-induced carrier recombination is determined by both defect levels and carrier capture cross-sections. Density functional theory (DFT) has been widely and successfully used to predict defect levels, but only recently has work begun to focus on using DFT to determine carrier capture cross-sections. Lang and Henry developed the theory of carrier-capture by multiphonon emission in the 1970s and showed that carrier-capture cross-sections differ between defects primarily due to differences in their carrier capture activation energies. We present an approach to using DFT to calculate carrier capture activation energies that does not depend on an assumed configuration coordinate and that fully accounts for anharmonic effects, which can substantially modify carrier activation energies. We demonstrate our approach for intrinisic defects in GaAs and GaN and discuss how our results depend on the choice of exchange-correlation functional and the treatment of spin polarization. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

Discriminating a deep defect from shallow acceptors in supercell calculations: gallium antisite in GaAs

NASA Astrophysics Data System (ADS)

Schultz, Peter

To make reliable first principles predictions of defect energies in semiconductors, it is crucial to discriminate between effective-mass-like defects--for which existing supercell methods fail--and deep defects--for which density functional theory calculations can yield reliable predictions of defect energy levels. The gallium antisite GaAs is often associated with the 78/203 meV shallow double acceptor in Ga-rich gallium arsenide. Within a framework of level occupation patterns, analyses of structure and spin stabilization can be used within a supercell approach to distinguish localized deep defect states from shallow acceptors such as BAs. This systematic analysis determines that the gallium antisite is inconsistent with a shallow state, and cannot be the 78/203 shallow double acceptor. The properties of the Ga antisite in GaAs are described, predicting that the Ga antisite is a deep double acceptor and has two donor states, one of which might be accidentally shallow. -- Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

[Three-dimensional finite element analysis of three conjunctive methods of free iliac bone graft for established mandibular body defects].

PubMed

Wang, Dong; Yang, Zhuang-qun; Hu, Xiao-yi

2007-08-01

To analyze the stress and displacement distribution of 3D-FE models in three conjunctive methods of vascularized iliac bone graft for established mandibular body defects. Using computer image process technique, a series of spiral CT images were put into Ansys preprocess programe to establish three 3D-FE models of different conjunctions. The three 3D-FE models of established mandibular body defects by vascularized iliac bone graft were built up. The distribution of Von Mises stress and displacement around mandibular segment, grafted ilium, plates and screws was obtained. It may be determined successfully that the optimal conjunctive shape be the on-lay conjunction.

Scanning Electron Microscope Mapping System Developed for Detecting Surface Defects in Fatigue Specimens

NASA Technical Reports Server (NTRS)

Bonacuse, Peter J.; Kantzos, Peter T.

2002-01-01

An automated two-degree-of-freedom specimen positioning stage has been developed at the NASA Glenn Research Center to map and monitor defects in fatigue specimens. This system expedites the examination of the entire gauge section of fatigue specimens so that defects can be found using scanning electron microscopy (SEM). Translation and rotation stages are driven by microprocessor-based controllers that are, in turn, interfaced to a computer running custom-designed software. This system is currently being used to find and record the location of ceramic inclusions in powder metallurgy materials. The mapped inclusions are periodically examined during interrupted fatigue experiments. The number of cycles to initiate cracks from these inclusions and the rate of growth of initiated cracks can then be quantified. This information is necessary to quantify the effect of this type of defect on the durability of powder metallurgy materials. This system was developed with support of the Ultra Safe program.

Self-Healing Composite of Thermoset Polymer and Programmed Super Contraction Fibers

NASA Technical Reports Server (NTRS)

Li, Guoqiang (Inventor); Meng, Harper (Inventor)

2016-01-01

A composition comprising thermoset polymer, shape memory polymer to facilitate macro scale damage closure, and a thermoplastic polymer for molecular scale healing is disclosed; the composition has the ability to resolve structural defects by a bio-mimetic close-then heal process. In use, the shape memory polymer serves to bring surfaces of a structural defect into approximation, whereafter use of the thermoplastic polymer for molecular scale healing allowed for movement of the thermoplastic polymer into the defect and thus obtain molecular scale healing. The thermoplastic can be fibers, particles or spheres which are used by heating to a level at or above the thermoplastic's melting point, then cooling of the composition below the melting temperature of the thermoplastic. Compositions of the invention have the ability to not only close macroscopic defects, but also to do so repeatedly even if another wound/damage occurs in a previously healed/repaired area.

Early prenatal exposure to air pollution and its associations with birth defects in a state-wide birth cohort from North Carolina.

PubMed

Vinikoor-Imler, Lisa C; Davis, J Allen; Meyer, Robert E; Luben, Thomas J

2013-10-01

Few studies have examined the potential relationship between air pollution and birth defects. The objective of this study was to investigate whether maternal exposure to particulate matter (PM2.5 ) and ozone (O3 ) during pregnancy is associated with birth defects among women living throughout North Carolina. Information on maternal and infant characteristics was obtained from North Carolina birth certificates and health service data (2003-2005) and linked with information on birth defects from the North Carolina Birth Defects Monitoring Program. The 24-hr PM2.5 and O3 concentrations were estimated using a hierarchical Bayesian model of air pollution generated by combining modeled air pollution predictions from the U.S. Environmental Protection Agency's Community Multi-Scale Air Quality model with air monitor data from the Environmental Protection Agency's Air Quality System. Maternal residence was geocoded and assigned pollutant concentrations averaged over weeks 3 to 8 of gestation. Binomial regression was performed and adjusted for potential confounders. No association was observed between either PM2.5 or O3 concentrations and most birth defects. Positive effect estimates were observed between air pollution and microtia/anotia and lower limb deficiency defects, but the 95% confidence intervals were wide and included the null. Overall, this study suggested a possible relationship between air pollution concentration during early pregnancy and certain birth defects (e.g., microtia/anotia, lower limb deficiency defects), although this study did not have the power to detect such an association. The risk for most birth defects does not appear to be affected by ambient air pollution. Copyright © 2013 Wiley Periodicals, Inc.

Increasing reticle inspection efficiency and reducing wafer printchecks at 14nm using automated defect classification and simulation

NASA Astrophysics Data System (ADS)

Paracha, Shazad; Goodman, Eliot; Eynon, Benjamin G.; Noyes, Ben F.; Ha, Steven; Kim, Jong-Min; Lee, Dong-Seok; Lee, Dong-Heok; Cho, Sang-Soo; Ham, Young M.; Vacca, Anthony D.; Fiekowsky, Peter J.; Fiekowsky, Daniel I.

2014-10-01

IC fabs inspect critical masks on a regular basis to ensure high wafer yields. These requalification inspections are costly for many reasons including the capital equipment, system maintenance, and labor costs. In addition, masks typically remain in the "requal" phase for extended, non-productive periods of time. The overall "requal" cycle time in which reticles remain non-productive is challenging to control. Shipping schedules can slip when wafer lots are put on hold until the master critical layer reticle is returned to production. Unfortunately, substituting backup critical layer reticles can significantly reduce an otherwise tightly controlled process window adversely affecting wafer yields. One major requal cycle time component is the disposition process of mask inspections containing hundreds of defects. Not only is precious non-productive time extended by reviewing hundreds of potentially yield-limiting detections, each additional classification increases the risk of manual review techniques accidentally passing real yield limiting defects. Even assuming all defects of interest are flagged by operators, how can any person's judgment be confident regarding lithographic impact of such defects? The time reticles spend away from scanners combined with potential yield loss due to lithographic uncertainty presents significant cycle time loss and increased production costs An automatic defect analysis system (ADAS), which has been in fab production for numerous years, has been improved to handle the new challenges of 14nm node automate reticle defect classification by simulating each defect's printability under the intended illumination conditions. In this study, we have created programmed defects on a production 14nm node critical-layer reticle. These defects have been analyzed with lithographic simulation software and compared to the results of both AIMS optical simulation and to actual wafer prints.

Maternal residential exposure to agricultural pesticides and birth defects in a 2003 to 2005 North Carolina birth cohort.

PubMed

Rappazzo, Kristen M; Warren, Joshua L; Meyer, Robert E; Herring, Amy H; Sanders, Alison P; Brownstein, Naomi C; Luben, Thomas J

2016-04-01

Birth defects are responsible for a large proportion of disability and infant mortality. Exposure to a variety of pesticides have been linked to increased risk of birth defects. We conducted a case-control study to estimate the associations between a residence-based metric of agricultural pesticide exposure and birth defects. We linked singleton live birth records for 2003 to 2005 from the North Carolina (NC) State Center for Health Statistics to data from the NC Birth Defects Monitoring Program. Included women had residence at delivery inside NC and infants with gestational ages from 20 to 44 weeks (n = 304,906). Pesticide exposure was assigned using a previously constructed metric, estimating total chemical exposure (pounds of active ingredient) based on crops within 500 meters of maternal residence, specific dates of pregnancy, and chemical application dates based on the planting/harvesting dates of each crop. Logistic regression was used to estimate odds ratios (ORs) and 95% confidence intervals for four categories of exposure (<10(th) , 10-50(th) , 50-90(th) , and >90(th) percentiles) compared with unexposed. Models were adjusted for maternal race, age at delivery, education, marital status, and smoking status. We observed elevated ORs for congenital heart defects and certain structural defects affecting the gastrointestinal, genitourinary and musculoskeletal systems (e.g., OR [95% confidence interval] [highest exposure vs. unexposed] for tracheal esophageal fistula/esophageal atresia = 1.98 [0.69, 5.66], and OR for atrial septal defects: 1.70 [1.34, 2.14]). Our results provide some evidence of associations between residential exposure to agricultural pesticides and several birth defects phenotypes. Birth Defects Research (Part A) 106:240-249, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Combining DFT, Cluster Expansions, and KMC to Model Point Defects in Alloys

NASA Astrophysics Data System (ADS)

Modine, N. A.; Wright, A. F.; Lee, S. R.; Foiles, S. M.; Battaile, C. C.; Thomas, J. C.; van der Ven, A.

In an alloy, defect energies are sensitive to the occupations of nearby atomic sites, which leads to a distribution of defect properties. When radiation-induced defects diffuse from their initially non-equilibrium locations, this distribution becomes time-dependent. The defects can become trapped in energetically favorable regions of the alloy leading to a diffusion rate that slows dramatically with time. Density Functional Theory (DFT) allows the accurate determination of ground state and transition state energies for a defect in a particular alloy environment but requires thousands of processing hours for each such calculation. Kinetic Monte-Carlo (KMC) can be used to model defect diffusion and the changing distribution of defect properties but requires energy evaluations for millions of local environments. We have used the Cluster Expansion (CE) formalism to ``glue'' together these seemingly incompatible methods. The occupation of each alloy site is represented by an Ising-like variable, and products of these variables are used to expand quantities of interest. Once a CE is fit to a training set of DFT energies, it allows very rapid evaluation of the energy for an arbitrary configuration, while maintaining the accuracy of the underlying DFT calculations. These energy evaluations are then used to drive our KMC simulations. We will demonstrate the application of our DFT/MC/KMC approach to model thermal and carrier-induced diffusion of intrinsic point defects in III-V alloys. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE.

Relating the defect band gap and the density functional band gap

NASA Astrophysics Data System (ADS)

Schultz, Peter; Edwards, Arthur

2014-03-01

Density functional theory (DFT) is an important tool to probe the physics of materials. The Kohn-Sham (KS) gap in DFT is typically (much) smaller than the observed band gap for materials in nature, the infamous ``band gap problem.'' Accurate prediction of defect energy levels is often claimed to be a casualty--the band gap defines the energy scale for defect levels. By applying rigorous control of boundary conditions in size-converged supercell calculations, however, we compute defect levels in Si and GaAs with accuracies of ~0.1 eV, across the full gap, unhampered by a band gap problem. Using GaAs as a theoretical laboratory, we show that the defect band gap--the span of computed defect levels--is insensitive to variations in the KS gap (with functional and pseudopotential), these KS gaps ranging from 0.1 to 1.1 eV. The defect gap matches the experimental 1.52 eV gap. The computed defect gaps for several other III-V, II-VI, I-VII, and other compounds also agree with the experimental gap, and show no correlation with the KS gap. Where, then, is the band gap problem? This talk presents these results, discusses why the defect gap and the KS gap are distinct, implying that current understanding of what the ``band gap problem'' means--and how to ``fix'' it--need to be rethought. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the U.S. Department of Energy's NNSA under contract DE-AC04-94AL85000.

Computer simulation analysis of normal and abnormal development of the mammalian diaphragm

PubMed Central

Fisher, Jason C; Bodenstein, Lawrence

2006-01-01

Background Congenital diaphragmatic hernia (CDH) is a birth defect with significant morbidity and mortality. Knowledge of diaphragm morphogenesis and the aberrations leading to CDH is limited. Although classical embryologists described the diaphragm as arising from the septum transversum, pleuroperitoneal folds (PPF), esophageal mesentery and body wall, animal studies suggest that the PPF is the major, if not sole, contributor to the muscular diaphragm. Recently, a posterior defect in the PPF has been identified when the teratogen nitrofen is used to induce CDH in fetal rodents. We describe use of a cell-based computer modeling system (Nudge++™) to study diaphragm morphogenesis. Methods and results Key diaphragmatic structures were digitized from transverse serial sections of paraffin-embedded mouse embryos at embryonic days 11.5 and 13. Structure boundaries and simulated cells were combined in the Nudge++™ software. Model cells were assigned putative behavioral programs, and these programs were progressively modified to produce a diaphragm consistent with the observed anatomy in rodents. Homology between our model and recent anatomical observations occurred under the following simulation conditions: (1) cell mitoses are restricted to the edge of growing tissue; (2) cells near the chest wall remain mitotically active; (3) mitotically active non-edge cells migrate toward the chest wall; and (4) movement direction depends on clonal differentiation between anterior and posterior PPF cells. Conclusion With the PPF as the sole source of mitotic cells, an early defect in the PPF evolves into a posteromedial diaphragm defect, similar to that of the rodent nitrofen CDH model. A posterolateral defect, as occurs in human CDH, would be more readily recreated by invoking other cellular contributions. Our results suggest that recent reports of PPF-dominated diaphragm morphogenesis in the rodent may not be strictly applicable to man. The ability to recreate a CDH defect using a combination of experimental data and testable hypotheses gives impetus to simulation modeling as an adjunct to experimental analysis of diaphragm morphogenesis. PMID:16483386

Computer simulation analysis of normal and abnormal development of the mammalian diaphragm.

PubMed

Fisher, Jason C; Bodenstein, Lawrence

2006-02-17

Congenital diaphragmatic hernia (CDH) is a birth defect with significant morbidity and mortality. Knowledge of diaphragm morphogenesis and the aberrations leading to CDH is limited. Although classical embryologists described the diaphragm as arising from the septum transversum, pleuroperitoneal folds (PPF), esophageal mesentery and body wall, animal studies suggest that the PPF is the major, if not sole, contributor to the muscular diaphragm. Recently, a posterior defect in the PPF has been identified when the teratogen nitrofen is used to induce CDH in fetal rodents. We describe use of a cell-based computer modeling system (Nudge++) to study diaphragm morphogenesis. Key diaphragmatic structures were digitized from transverse serial sections of paraffin-embedded mouse embryos at embryonic days 11.5 and 13. Structure boundaries and simulated cells were combined in the Nudge++ software. Model cells were assigned putative behavioral programs, and these programs were progressively modified to produce a diaphragm consistent with the observed anatomy in rodents. Homology between our model and recent anatomical observations occurred under the following simulation conditions: (1) cell mitoses are restricted to the edge of growing tissue; (2) cells near the chest wall remain mitotically active; (3) mitotically active non-edge cells migrate toward the chest wall; and (4) movement direction depends on clonal differentiation between anterior and posterior PPF cells. With the PPF as the sole source of mitotic cells, an early defect in the PPF evolves into a posteromedial diaphragm defect, similar to that of the rodent nitrofen CDH model. A posterolateral defect, as occurs in human CDH, would be more readily recreated by invoking other cellular contributions. Our results suggest that recent reports of PPF-dominated diaphragm morphogenesis in the rodent may not be strictly applicable to man. The ability to recreate a CDH defect using a combination of experimental data and testable hypotheses gives impetus to simulation modeling as an adjunct to experimental analysis of diaphragm morphogenesis.

Introduction of English Immersion in China: A Transplant with Modifications

ERIC Educational Resources Information Center

Qiang, Haiyan; Siegel, Linda S.

2012-01-01

This article presents an overview of replicating the French immersion model used in Canada to English immersion programs in China. It provides the Chinese context of this program highlighting the importance of English education and the defect of traditional English teaching and learning. The paper explains the borrowable features of the French…

75 FR 78725 - Recreational Boating Safety Projects, Programs and Activities Funded Under Provisions of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-16

... defect. ($17,335). Web-based Document Management System: Funding was provided to continue to provide a web-based document management system to better enable the handling of thousands of recreational... program strategy support to the nation-wide RBS effort. The goal is to coordinate the RBS outreach...

Preparation for Parenthood. Evaluation Plan and Program Evaluation.

ERIC Educational Resources Information Center

Blackmon, Michael E.

Preparation for Parenthood is a city-wide program designed for the purpose of: (1) decreasing the complication of pregnancy for school-age girls due to poor nutrition and poor prenatal care, and consequently reducing infant mortality, mental retardation, and birth defects; and (2) enabling the girls to continue their educational ambitions, thus…

THE SCHOOL HEALTH AND SAFETY PROGRAM.

ERIC Educational Resources Information Center

1963

INVOLVING INDIVIDUALS AS WELL AS ORGANIZATIONS, THE PROGRAM AIMED AT THE OPTIMUM HEALTH OF ALL CHILDREN, AND IMPROVEMENT OF HEALTH AND SAFETY STANDARDS WITHIN THE COMMUNITY. EACH OF THE CHILDREN WAS URGED TO HAVE A SUCCESSFUL VACCINATION FOR SMALL POX, THE DPT SERIES AND BOOSTER, THE POLIO SERIES, AND CORRECTIONS OF ALL DENTAL DEFECTS AND…

Maternal SENP7 programs meiosis architecture and embryo survival in mouse.

PubMed

Huang, Chun-Jie; Wu, Di; Jiao, Xiao-Fei; Khan, Faheem Ahmed; Xiong, Cheng-Liang; Liu, Xiao-Ming; Yang, Jing; Yin, Tai-Lang; Huo, Li-Jun

2017-07-01

Understanding the mechanisms underlying abnormal egg production and pregnancy loss is significant for human fertility. SENP7, a SUMO poly-chain editing enzyme, has been regarded as a mitotic regulator of heterochromatin integrity and DNA repair. Herein, we report the roles of SENP7 in mammalian reproductive scenario. Mouse oocytes deficient in SENP7 experienced meiotic arrest at prophase I and metaphase I stages, causing a substantial decrease of mature eggs. Hyperaceylation and hypomethylation of histone H3 and up-regulation of Cdc14B/C accompanied by down-regulation of CyclinB1 and CyclinB2 were further recognized as contributors to defective M-phase entry and spindle assembly in oocytes. The spindle assembly checkpoint activated by defective spindle morphogenesis, which was also caused by mislocalization and ubiquitylation-mediated proteasomal degradation of γ-tubulin, blocked oocytes at meiosis I stage. SENP7-depleted embryos exhibited severely defective maternal-zygotic transition and progressive degeneration, resulting in nearly no blastocyst production. The disrupted epigenetic landscape on histone H3 restricted Rad51C loading onto DNA lesions due to elevated HP1α euchromatic deposition, and reduced DNA 5hmC challenged the permissive status for zygotic DNA repair, which induce embryo death. Our study pinpoints SENP7 as a novel determinant in epigenetic programming and major pathways that govern oocyte and embryo development programs in mammals. Copyright © 2017 Elsevier B.V. All rights reserved.

Digital volume tomography in the diagnosis of peri-implant defects: an in vitro study on native pig mandibles.

PubMed

Mengel, Reiner; Kruse, Björn; Flores-de-Jacoby, Lavin

2006-07-01

The aim of this study of native pig mandibles was to investigate the accuracy and quality of the representation of peri-implant defects by intraoral radiography (IR), panoramic radiography (PR), computer tomography (CT), and digital volume tomography (DVT). The examination was carried out on 19 native pig mandibles. In the toothless sections of the mandibles, one or two implants were inserted. Following the standardized preparation of peri-implant defects (11 each of dehiscences, fenestrations, and 2- to 3-walled intrabony defects), IR, PR, CT, and DVT were performed. The peri-implant defects were measured using appropriate software on the digitized IR and PR image programs. As a control method, the peri-implant bone defects were measured directly using a reflecting stereomicroscope with measuring ocular. The statistical comparison between the measurements of the radiographic scans and those of the direct readings of the peri-implant defects was performed with Pearson's correlation coefficient. The quality of the radiographic scans was determined through the subjective perception and detectability of the peri-implant defects by five independent observers. In the DVT and CT scans, it was possible to measure all the bone defects in three planes. Comparison with the direct peri-implant defect measurements yielded a mean deviation of 0.17+/-0.11 mm for the DVT scans and 0.18+/-0.12 mm for the CT scans. On the IR and PR images, the defects could be detected only in the mesio-distal and cranio-caudal planes. In comparison with the direct measurements of the peri-implant defects, the IR images revealed a mean deviation of 0.34+/-0.30 mm, and the PR images revealed a mean deviation of 0.41+/-0.35 mm. The quality rating of the radiographic images was highest for the DVT scans. Overall, the CT and DVT scans displayed only a slight deviation in the extent of the peri-implant defects. Both radiographic imaging techniques permitted imaging of peri-implant defects in three planes, true to scale, and without overlay or distortion. The DVT scans showed the best imaging quality.

Developmental programming: postnatal estradiol modulation of prenatally organized reproductive neuroendocrine function in sheep.

PubMed

Puttabyatappa, Muraly; Cardoso, Rodolfo C; Herkimer, Carol; Veiga-Lopez, Almudena; Padmanabhan, Vasantha

2016-08-01

Gestational testosterone (TS) excess, acting via both the androgenic and estrogenic pathways, advances puberty and disrupts the neuroendocrine estradiol (E2) feedback and periovulatory hormonal dynamics in female sheep. These prenatally programmed defects may be subject to postnatal modifications by continued organizational and/or activational effects of steroids. This study investigated (1) the organizational contribution of prenatal estrogen excess and (2) the impact of postnatal exposure to E2 in modulating the effects of prenatal androgen excess (TS and dihydrotestosterone (DHT)) on puberty, neuroendocrine feedback mechanisms, and periovulatory hormonal dynamics in sheep. Pregnant Suffolk sheep were treated with TS, DHT, E2, or E2 plus DHT (ED) from days 30 to 90 of gestation. A subset of the control (C), TS, and DHT female offspring received a constant-release E2 implant postnatally. Findings revealed that (1) prenatal E2-treatment failed to reproduce the neuroendocrine disruptions predicted to be programmed by the estrogenic pathway and (2) prenatal E2D-treatment did not adequately replicate the reproductive neuroendocrine defects induced by prenatal TS excess. More importantly, continuous postnatal E2-treatment, while delaying the onset of puberty and reducing the inhibitory effects of E2 on tonic luteinizing hormone (LH) release, failed to amplify the E2-positive feedback and periovulatory defects induced by prenatal TS-treatment. Our results indicate that disruptions in E2-positive feedback mechanisms and periovulatory gonadotropin secretion induced by prenatal TS-treatment are programmed predominantly during the prenatal life with postnatal exposure to E2 excess not contributing further to these disruptions. © 2016 Society for Reproduction and Fertility.

Defense Small Business Innovation Research Program (SBIR). Volume 3. Air Force Abstracts of Phase 1 Awards

DTIC Science & Technology

1990-01-01

THERE WILL BE A CONTINUING NEED FOR A SENSITIVE, RAPID, AND ECONOMICAL TESTING PROCEDURE CAPABLE OF DETECTING DEFECTS AND PROVIDING FEEDBACK FOR QUALITY...SOLUTIONS. THE DKF METHOD PROVIDES OPTIMAL OR NEAR-OPTIMAL ACCURACY, REDUCE PROCESSING BURDEN, AND IMPROVE FAULT TOLERANCE. THE DKF/MMAE ( DMAE ) TECHNIQUES...DEVICES FOR B-SiC IS TO BE ABLE TO CONSISTENTLY PRODUCE INTRINSIC FILMS WITH VERY LOW DEFECTS AND TO DEVELOP SCHOTTKY AND OHMIC CONTACT MATERIALS THAT WILL

Cost-Sensitive Radial Basis Function Neural Network Classifier for Software Defect Prediction

PubMed Central

Venkatesan, R.

2016-01-01

Effective prediction of software modules, those that are prone to defects, will enable software developers to achieve efficient allocation of resources and to concentrate on quality assurance activities. The process of software development life cycle basically includes design, analysis, implementation, testing, and release phases. Generally, software testing is a critical task in the software development process wherein it is to save time and budget by detecting defects at the earliest and deliver a product without defects to the customers. This testing phase should be carefully operated in an effective manner to release a defect-free (bug-free) software product to the customers. In order to improve the software testing process, fault prediction methods identify the software parts that are more noted to be defect-prone. This paper proposes a prediction approach based on conventional radial basis function neural network (RBFNN) and the novel adaptive dimensional biogeography based optimization (ADBBO) model. The developed ADBBO based RBFNN model is tested with five publicly available datasets from the NASA data program repository. The computed results prove the effectiveness of the proposed ADBBO-RBFNN classifier approach with respect to the considered metrics in comparison with that of the early predictors available in the literature for the same datasets. PMID:27738649

Cost-Sensitive Radial Basis Function Neural Network Classifier for Software Defect Prediction.

PubMed

Kumudha, P; Venkatesan, R

Effective prediction of software modules, those that are prone to defects, will enable software developers to achieve efficient allocation of resources and to concentrate on quality assurance activities. The process of software development life cycle basically includes design, analysis, implementation, testing, and release phases. Generally, software testing is a critical task in the software development process wherein it is to save time and budget by detecting defects at the earliest and deliver a product without defects to the customers. This testing phase should be carefully operated in an effective manner to release a defect-free (bug-free) software product to the customers. In order to improve the software testing process, fault prediction methods identify the software parts that are more noted to be defect-prone. This paper proposes a prediction approach based on conventional radial basis function neural network (RBFNN) and the novel adaptive dimensional biogeography based optimization (ADBBO) model. The developed ADBBO based RBFNN model is tested with five publicly available datasets from the NASA data program repository. The computed results prove the effectiveness of the proposed ADBBO-RBFNN classifier approach with respect to the considered metrics in comparison with that of the early predictors available in the literature for the same datasets.

Bendectin and birth defects. II: Ecological analyses.

PubMed

Kutcher, Jeffrey S; Engle, Arnold; Firth, Jacqueline; Lamm, Steven H

2003-02-01

Bendectin was the primary pharmaceutical treatment of nausea and vomiting of pregnancy (NVP) in the United States until the early 1980s. Its manufacture was then discontinued after public allegations that it was causing birth defects. Subsequently, meta-analyses of the many epidemiological cohort and case/control studies used to examine that hypothesis have demonstrated the absence of a detectable teratogenic effect. This study presents an ecological analysis of the same hypothesis that examines specific malformations. Annual birth defect prevalence data for the 1970s to the 1990s have been obtained for specific birth defects from the Center for Disease Control's nationwide Birth Defect Monitoring Program. These data for the US have been compared graphically to the annual US Bendectin sales for the treatment of NVP. Data have also been obtained for annual US rates for hospitalization for NVP. The three data sets have been temporally compared in graphic analysis. The temporal trends in prevalence rates for specific birth defects examined from 1970 through 1992 did not show changes that reflected the cessation of Bendectin use over the 1980-84 period. Further, the NVP hospitalization rate doubled when Bendectin use ceased. The population results of the ecological analyses complement the person-specific results of the epidemiological analyses in finding no evidence of a teratogenic effect from the use of Bendectin.

Congenital Heart Defects and Receipt of Special Education Services.

PubMed

Riehle-Colarusso, Tiffany; Autry, Andrew; Razzaghi, Hilda; Boyle, Coleen A; Mahle, William T; Van Naarden Braun, Kim; Correa, Adolfo

2015-09-01

We investigated the prevalence of receipt of special education services among children with congenital heart defects (CHDs) compared with children without birth defects. Children born from 1982 to 2004 in metropolitan Atlanta with CHDs (n = 3744) were identified from a population-based birth defect surveillance program; children without birth defects (n = 860 715) were identified from birth certificates. Cohorts were linked to special education files for the 1992-2012 school years to identify special education services. Children with noncardiac defects or genetic syndromes were excluded; children with CHDs were classified by presence or absence of critical CHDs (ie, CHDs requiring intervention by age one year). We evaluated the prevalence of receipt of special education services and prevalence rate ratios using children without birth defects as a reference. Compared with children without birth defects, children with CHDs were 50% more likely to receive special education services overall (adjusted prevalence rate ratio [aPRR] = 1.5; 95% confidence interval [CI]: 1.4-1.7). Specifically, they had higher prevalence of several special education categories including: intellectual disability (aPRR = 3.8; 95% CI: 2.8-5.1), sensory impairment (aPRR = 3.0; 95% CI: 1.8-5.0), other health impairment (aPRR = 2.8; 95% CI: 2.2-3.5), significant developmental delay (aPRR = 1.9; 95% CI: 1.3-2.8), and specific learning disability (aPRR = 1.4; 95% CI: 1.1-1.7). For most special education services, the excess prevalence did not vary by presence of critical CHDs. Children with CHDs received special education services more often than children without birth defects. These findings highlight the need for special education services and the importance of developmental screening for all children with CHDs. Copyright © 2015 by the American Academy of Pediatrics.

Surface Inspection Tool for Optical Detection of Surface Defects

NASA Technical Reports Server (NTRS)

Nurge, Mark; Youngquist, Robert; Dyer, Dustin

2013-01-01

The Space Shuttle Orbiter windows were damaged both by micrometeor impacts and by handling, and required careful inspection before they could be reused. The launch commit criteria required that no defect be deeper than a critical depth. The shuttle program used a refocus microscope to perform a quick pass/fail determination, and then followed up with mold impressions to better quantify any defect. However, the refocus microscope is slow and tedious to use due to its limited field of view, only focusing on one small area of glass at a time. Additionally, the unit is bulky and unable to be used in areas with tight access, such as defects near the window frame or on the glass inside the Orbiter due to interference with the dashboard. The surface inspection tool is a low-profile handheld instrument that provides two digital video images on a computer for monitoring surface defects. The first image is a wide-angle view to assist the user in locating defects. The second provides an enlarged view of a defect centered in the window of the first image. The focus is adjustable for each of the images. However, the enlarged view was designed to have a focal plane with a short depth. This allows the user to get a feel for the depth of different parts of the defect under inspection as the focus control is varied. A light source is also provided to illuminate the defect, precluding the need for separate lighting tools. The software provides many controls to adjust image quality, along with the ability to zoom digitally the images and to capture and store them for later processing.

Comparison of binary mask defect printability analysis using virtual stepper system and aerial image microscope system

NASA Astrophysics Data System (ADS)

Phan, Khoi A.; Spence, Chris A.; Dakshina-Murthy, S.; Bala, Vidya; Williams, Alvina M.; Strener, Steve; Eandi, Richard D.; Li, Junling; Karklin, Linard

1999-12-01

As advanced process technologies in the wafer fabs push the patterning processes toward lower k1 factor for sub-wavelength resolution printing, reticles are required to use optical proximity correction (OPC) and phase-shifted mask (PSM) for resolution enhancement. For OPC/PSM mask technology, defect printability is one of the major concerns. Current reticle inspection tools available on the market sometimes are not capable of consistently differentiating between an OPC feature and a true random defect. Due to the process complexity and high cost associated with the making of OPC/PSM reticles, it is important for both mask shops and lithography engineers to understand the impact of different defect types and sizes to the printability. Aerial Image Measurement System (AIMS) has been used in the mask shops for a number of years for reticle applications such as aerial image simulation and transmission measurement of repaired defects. The Virtual Stepper System (VSS) provides an alternative method to do defect printability simulation and analysis using reticle images captured by an optical inspection or review system. In this paper, pre- programmed defects and repairs from a Defect Sensitivity Monitor (DSM) reticle with 200 nm minimum features (at 1x) will be studied for printability. The simulated resist lines by AIMS and VSS are both compared to SEM images of resist wafers qualitatively and quantitatively using CD verification.Process window comparison between unrepaired and repaired defects for both good and bad repair cases will be shown. The effect of mask repairs to resist pattern images for the binary mask case will be discussed. AIMS simulation was done at the International Sematech, Virtual stepper simulation at Zygo and resist wafers were processed at AMD-Submicron Development Center using a DUV lithographic process for 0.18 micrometer Logic process technology.

Application of Terahertz Imaging and Backscatter Radiography to Space Shuttle Foam Inspection

NASA Technical Reports Server (NTRS)

Ussery, Warren

2008-01-01

Two state of the art technologies have been developed for External Fuel Tank foam inspections. Results of POD tests have shown Backscatter Radiography and Terahertz imaging detect critical defects with no false positive issue. These techniques are currently in use on the External Tank program as one component in the foam quality assurance program.

38 CFR 21.8012 - Vocational training program for certain children of Vietnam veterans and veterans with covered...

Code of Federal Regulations, 2014 CFR

2014-07-01

... program for certain children of Vietnam veterans and veterans with covered service in Korea-spina bifida... Rehabilitation for Certain Children of Vietnam Veterans and Veterans with Covered Service in Korea-Spina Bifida... Vietnam veterans and veterans with covered service in Korea—spina bifida and covered birth defects. VA...

38 CFR 21.8012 - Vocational training program for certain children of Vietnam veterans and veterans with covered...

Code of Federal Regulations, 2013 CFR

2013-07-01

... program for certain children of Vietnam veterans and veterans with covered service in Korea-spina bifida... Rehabilitation for Certain Children of Vietnam Veterans and Veterans with Covered Service in Korea-Spina Bifida... Vietnam veterans and veterans with covered service in Korea—spina bifida and covered birth defects. VA...

38 CFR 21.8012 - Vocational training program for certain children of Vietnam veterans and veterans with covered...

Code of Federal Regulations, 2012 CFR

2012-07-01

... program for certain children of Vietnam veterans and veterans with covered service in Korea-spina bifida... Rehabilitation for Certain Children of Vietnam Veterans and Veterans with Covered Service in Korea-Spina Bifida... Vietnam veterans and veterans with covered service in Korea—spina bifida and covered birth defects. VA...

38 CFR 21.8012 - Vocational training program for certain children of Vietnam veterans and veterans with covered...

Code of Federal Regulations, 2011 CFR

2011-07-01

... program for certain children of Vietnam veterans and veterans with covered service in Korea-spina bifida... Rehabilitation for Certain Children of Vietnam Veterans and Veterans with Covered Service in Korea-Spina Bifida... Vietnam veterans and veterans with covered service in Korea—spina bifida and covered birth defects. VA...

CROMAX : a crosscut-first computer simulation program to determine cutting yield

Treesearch

Pamela J. Giese; Jeanne D. Danielson

1983-01-01

CROMAX simulates crosscut-first, then rip operations as commonly practiced in furniture manufacture. This program calculates cutting yields from individual boards based on board size and defect location. Such information can be useful in predicting yield from various grades and grade mixes thereby allowing for better management decisions in the rough mill. The computer...

Test program for transmitter experiment package and heat pipe system for the communications technology satellite

NASA Technical Reports Server (NTRS)

Depauw, J. F.; Reader, K. E.; Staskus, J. V.

1976-01-01

The test program is described for the 200 watt transmitter experiment package and the variable conductance heat pipe system which are components of the high-power transponder aboard the Communications Technology Satellite. The program includes qualification tests to demonstrate design adequacy, acceptance tests to expose latent defects in flight hardware, and development tests to integrate the components into the transponder system and to demonstrate compatibility.

Relationship between progression of visual field defect and intraocular pressure in primary open-angle glaucoma.

PubMed

Naito, Tomoko; Yoshikawa, Keiji; Mizoue, Shiro; Nanno, Mami; Kimura, Tairo; Suzumura, Hirotaka; Shiraga, Fumio

2015-01-01

To analyze the relationship between intraocular pressure (IOP) and the progression of visual field defects in Japanese primary open-angle glaucoma (POAG) and normal-tension glaucoma (NTG) patients. The subjects of the study were patients undergoing treatment for POAG or NTG who had performed visual field tests at least ten times with a Humphrey field analyzer (Swedish interactive thresholding algorithm standard, C30-2 program). The progression of visual field defects was defined by a significantly negative value of the mean deviation slope at the final visual field test during the follow-up period. The relationships between the progression of visual field defects and IOP, as well as other clinical factors, were retrospectively analyzed. A total of 156 eyes of 156 patients were included in the analysis. Significant progression of visual field defects was observed in 70 eyes of 70 patients (44.9%), while no significant progression was evident in 86 eyes of 86 patients (55.1%). The eyes with visual field defect progression had significantly lower baseline IOP (P<0.05), as well as significantly lower IOP reduction rate (P<0.01). The standard deviation of IOP values during follow-up was significantly greater in the eyes with visual field defect progression than in eyes without (P<0.05). Reducing IOP is thought to be useful for Japanese POAG or NTG patients to suppress the progression of visual field defects. In NTG, IOP management should take into account not only achieving the target IOP, but also minimizing the fluctuation of IOP during follow-up period.

Specific Location of Disc Hemorrhage is Linked to Nerve Fiber Layer Defects.

PubMed

Yoo, Young Cheol; Kim, Joon Mo; Park, Han Seok; Yoo, Chungkwon; Shim, Seong Hee; Won, Yu Sam; Park, Ki Ho; Chang, Robert T

2017-06-01

To investigate the relationship between retinal nerve fiber layer (RNFL) defects and the quadrant and proximal location of disc hemorrhages (DHs) in a large population examined for health screening. A total of 168,044 subjects older than 20 years underwent a single screening ophthalmic examination with color fundus photography as part of a comprehensive health screening program. The presence and location of DHs and RNFL defects were assessed. The DH locations were defined according to the quadrant location (inferotemporal, superotemporal, inferonasal, or superonasal) and the most proximal end of DHs relative to the disc center (cup base, cup margin, disc rim, or extrapapillary region). Using these two location descriptors as independent variables, a logistic regression analysis was conducted to explore the effects of DH location on RNFL defects. Two hundred twenty-six eyes had DH and 120 (53.1%) of them had RNFL defects. After adjusting for proximal location, DHs located in the inferotemporal quadrant accompanied RFNL defects 12 times more frequently than those in the superonasal quadrant (odds ratio [OR], 11.81; P = .004). Conversely, after adjusting for quadrant location, the ORs for an associated RNFL defect were 3.73 (P < .001), 16.54 (P < .001), and 8.91 (P = .002) for DHs with the proximal end at the disc rim, cup margin, and cup base, respectively. Among the four quadrants and four proximal locations, DHs were identified most frequently in the inferotemporal quadrant and outside the disc, respectively. Some DH locations, such as the inferotemporal quadrant and the cup margin, were associated with RNFL defects, whereas others were not.

Photomask quality assessment solution for 90-nm technology node

NASA Astrophysics Data System (ADS)

Ohira, Katsumi; Chung, Dong Hoon P.; Nobuyuki, Yoshioka; Tateno, Motonari; Matsumura, Kenichi; Chen, Jiunn-Hung; Luk-Pat, Gerard T.; Fukui, Norio; Tanaka, Yoshio

2004-08-01

As 90 nm LSI devices are about to enter pre-production, the cost and turn-around time of photomasks for such devices will be key factors for success in device production. Such devices will be manufactured with state-of-the-art 193nm photolithography systems. Photomasks for these devices are being produced with the most advanced equipment, material and processing technologies and yet, quality assurance still remains an issue for volume production. These issues include defect classification and disposition due to the insufficient resolution of the defect inspection system at conventional review and classification processes and to aggressive RETs, uncertainty of the impact the defects have on the printed feature as well as inconsistencies of classical defect specifications as applied in the sub-wavelength era are becoming a serious problem. Simulation-based photomask qualification using the Virtual Stepper System is widely accepted today as a reliable mask quality assessment tool of mask defects for both the 180 nm and 130 nm technology nodes. This study examines the extendibility of the Virtual Stepper System to 90nm technology node. The proposed method of simulation-based mask qualification uses aerial image defect simulation in combination with a next generation DUV inspection system with shorter wavelength (266nm) and small pixel size combined with DUV high-resolution microscope for some defect cases. This paper will present experimental results that prove the applicability for enabling 90nm technology nodes. Both contact and line/space patterns with varies programmed defects on ArF Attenuated PSM will be used. This paper will also address how to make the strategy production-worthy.

Chemicalome and metabolome profiling of polymethoxylated flavonoids in Citri Reticulatae Pericarpium based on an integrated strategy combining background subtraction and modified mass defect filter in a Microsoft Excel Platform.

PubMed

Zeng, Su-Ling; Duan, Li; Chen, Bai-Zhong; Li, Ping; Liu, E-Hu

2017-07-28

Detection of metabolites in complex biological matrixes is a great challenge because of the background noise and endogenous components. Herein, we proposed an integrated strategy that combined background subtraction program and modified mass defect filter (MMDF) data mining in a Microsoft Excel platform for chemicalome and metabolome profiling of the polymethoxylated flavonoids (PMFs) in Citri Reticulatae Pericarpium (CRP). The exogenously-sourced ions were firstly filtered out by the developed Visual Basic for Applications (VBA) program incorporated in the Microsoft Office. The novel MMDF strategy was proposed for detecting both target and untarget constituents and metabolites based on narrow, well-defined mass defect ranges. The approach was validated to be powerful, and potentially useful for the metabolite identification of both single compound and homologous compound mixture. We successfully identified 30 and 31 metabolites from rat biosamples after oral administration of nobiletin and tangeretin, respectively. A total of 56 PMFs compounds were chemically characterized and 125 metabolites were captured. This work demonstrated the feasibility of the integrated approach for reliable characterization of the constituents and metabolites in herbal medicines. Copyright © 2017 Elsevier B.V. All rights reserved.

A coverage and slicing dependencies analysis for seeking software security defects.

PubMed

He, Hui; Zhang, Dongyan; Liu, Min; Zhang, Weizhe; Gao, Dongmin

2014-01-01

Software security defects have a serious impact on the software quality and reliability. It is a major hidden danger for the operation of a system that a software system has some security flaws. When the scale of the software increases, its vulnerability has becoming much more difficult to find out. Once these vulnerabilities are exploited, it may lead to great loss. In this situation, the concept of Software Assurance is carried out by some experts. And the automated fault localization technique is a part of the research of Software Assurance. Currently, automated fault localization method includes coverage based fault localization (CBFL) and program slicing. Both of the methods have their own location advantages and defects. In this paper, we have put forward a new method, named Reverse Data Dependence Analysis Model, which integrates the two methods by analyzing the program structure. On this basis, we finally proposed a new automated fault localization method. This method not only is automation lossless but also changes the basic location unit into single sentence, which makes the location effect more accurate. Through several experiments, we proved that our method is more effective. Furthermore, we analyzed the effectiveness among these existing methods and different faults.

Density functional calculations of multiphonon capture cross sections at defects in semiconductors

NASA Astrophysics Data System (ADS)

Barmparis, Georgios D.; Puzyrev, Yevgeniy S.; Zhang, X.-G.; Pantelides, Sokrates T.

2014-03-01

The theory of electron capture cross sections by multiphonon processes in semiconductors has a long and controversial history. Here we present a comprehensive theory and describe its implementation for realistic calculations. The Born-Oppenheimer and the Frank-Condon approximations are employed. The transition probability of an incoming electron is written as a product of an instantaneous electronic transition in the initial defect configuration and the line shape function (LSF) that describes the multiphonon processes that lead to lattice relaxation. The electronic matrix elements are calculated using the Projector Augmented Wave (PAW) method which yields the true wave functions while still employing a plane-wave basis. The LSF is calculated by employing a Monte Carlo method and the real phonon modes of the defect, calculated using density functional theory in the PAW scheme. Initial results of the capture cross section for a prototype system, namely a triply hydrogenated vacancy in Si are presented. The results are relevant for modeling device degradation by hot electron effects. This work is supported in part by the Samsung Advanced Institute of Technology (SAIT)'s Global Research Outreach (GRO) Program and by the LDRD program at ORNL.

Gastric pentadecapeptide BPC 157 promotes corneal epithelial defects healing in rats.

PubMed

Lazić, Ratimir; Gabrić, Nikica; Dekaris, Iva; Bosnar, Damir; Boban-Blagaić, Alenka; Sikirić, Predrag

2005-06-01

We evaluated the role of human gastric pentadecapeptide BPC 157 in corneal epithelial defects healing in rats. 48 rats, in 4 groups (N=12). Total debridement of corneal epithelium preformed unilaterally and lesions stained and photographed. Animals medicated as follows: distilled water (control group) or BPC 157 2 pg/ml, 2 ng/ml, 2 microg/ml, 2 drops/rat eye started immediately after injury induction, every 8 hours up to 40 hours (i.e., at 0, 8, 16, 24, 32, 40 h). Lesions were photographed before application or sacrifice (at 48 h). Defect area was analyzed using a special program. Through 48 hour period a steady recovery is noted in controls. Recovery was markedly accelerated in eyes on microg- or ng-topical regimen of BPC 157 (p < 0.05). Of note, unlike control lesion present also after 48 h, these lesions disappeared already following 40 h (microg) or 48 h (ng) post-injury. BPC 157 was shown to be effective in promoting corneal defects healing in rats. Results were dose dependent.

Uses of available record systems in epidemiologic studies of reproductive toxicology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Polednak, A.P.; Janerich, D.T.

The uses of available record systems in epidemiologic studies of reproductive toxicology are described with reference to New York State. The available record systems (and relevant reproductive end points) described include: a newborn screening program for metabolic diseases and hemoglobinopathies (relevant to point mutations); chromosome registries and prenatal cytogenetics (for chromosome anomalies); live birth certificates (for birth defects, birthweight, sex ratio, etc); fetal death certificates (for spontaneous fetal deaths); and a statewide cancer registry (for childhood cancers and transplacental carcinogenesis). The uses and limitations of these record systems are discussed, along with examples of their use in descriptive and analyticmore » epidemiologic studies. Descriptive studies outlined include investigations of temporal and geographic trends in birth defects, birth weight, and fetal deaths, with reference to environmental questions (eg, Love Canal, nuclear power plants). Analytic studies described concern parental occupation in relation to specific birth defects (neural tube defects and Down syndrome) and maternal use of contraceptive drugs.« less

Pattern Inspection of EUV Masks Using DUV Light

NASA Astrophysics Data System (ADS)

Liang, Ted; Tejnil, Edita; Stivers, Alan R.

2002-12-01

Inspection of extreme ultraviolet (EUV) lithography masks requires reflected light and this poses special challenges for inspection tool suppliers as well as for mask makers. Inspection must detect all the printable defects in the absorber pattern as well as printable process-related defects. Progress has been made under the NIST ATP project on "Intelligent Mask Inspection Systems for Next Generation Lithography" in assessing the factors that impact the inspection tool sensitivity. We report in this paper the inspection of EUV masks with programmed absorber defects using 257nm light. All the materials of interests for masks are highly absorptive to EUV light as compared to deep ultraviolet (DUV) light. Residues and contamination from mask fabrication process and handling are prone to be printable. Therefore, it is critical to understand their EUV printability and optical inspectability. Process related defects may include residual buffer layer such as oxide, organic contaminants and possible over-etch to the multilayer surface. Both simulation and experimental results will be presented in this paper.

Measurement Variability of Vertical Scanning Interferometry Tool Used for Orbiter Window Defect Assessment

NASA Technical Reports Server (NTRS)

Padula, Santo, II

2009-01-01

The ability to sufficiently measure orbiter window defects to allow for window recertification has been an ongoing challenge for the orbiter vehicle program. The recent Columbia accident has forced even tighter constraints on the criteria that must be met in order to recertify windows for flight. As a result, new techniques are being investigated to improve the reliability, accuracy and resolution of the defect detection process. The methodology devised in this work, which is based on the utilization of a vertical scanning interferometric (VSI) tool, shows great promise for meeting the ever increasing requirements for defect detection. This methodology has the potential of a 10-100 fold greater resolution of the true defect depth than can be obtained from the currently employed micrometer based methodology. An added benefit is that it also produces a digital elevation map of the defect, thereby providing information about the defect morphology which can be utilized to ascertain the type of debris that induced the damage. However, in order to successfully implement such a tool, a greater understanding of the resolution capability and measurement repeatability must be obtained. This work focused on assessing the variability of the VSI-based measurement methodology and revealed that the VSI measurement tool was more repeatable and more precise than the current micrometer based approach, even in situations where operator variation could affect the measurement. The analysis also showed that the VSI technique was relatively insensitive to the hardware and software settings employed, making the technique extremely robust and desirable

Holographic Techniques for Nondestructive Testing of Tires

DOT National Transportation Integrated Search

1972-04-01

Holographic interferometric techniques were used in a development program to evaluate the feasibility of the technique in the nondestructive testing (NDT) of commercial automobile tires. Passenger tires with built-in defects were holographically insp...

March of Dimes Birth Defects Foundation

MedlinePlus

... the loop I'M IN 2017 Premature Birth Report Cards See how prematurity affects your state and ... premature birth: The Prematurity Campaign About us Annual report Our work Community impact Global programs Research Need ...

Does Defection Matter The Impact of the Chieu Hoi Program in Vietnam

DTIC Science & Technology

2012-06-08

previous few years. Pacification Pacification began as a national initiative to improve economic, health , and educational conditions within South...the program and emphasized the importance of strengthening government politics in the village. New focus in the living conditions included health ...reforms and educational advancements: In health and education, the effort concentrated on eliminating illiteracy, making primary and secondary

Responsibility Factors of Reducing Inefficiencies in Information System Processes and Their Role on Intention to Acquire Six Sigma Certification

ERIC Educational Resources Information Center

Hejazi, Sara

2009-01-01

Organizations worldwide have been turning to Six Sigma program (SSP) to eliminate the defects in their products or drive out the variability in their processes to attain a competitive advantage in their marketplace. An effective certification program has been touted as a major contributor to successful implementation of SSP. An effective…

Maternal Residential Exposure to Agricultural Pesticides and ...

EPA Pesticide Factsheets

Birth defects are responsible for a large proportion of disability and infant mortality. Exposure to a variety of pesticides have been linked to increased risk of birth defects. We conducted a case-control study to estimate the associations between a residence-based metric of agricultural pesticide exposure and birth defects. We linked singleton live birth records for 2003-2005 from the North Carolina (NC) State Center for Health Statistics to data from the NC Birth Defects Monitoring Program. Included women had residence at delivery inside NC and infants with gestational ages from 20-44 weeks (n=304,906). Pesticide exposure was assigned using a previously constructed metric, estimating total chemical exposure (pounds of active ingredient) based on crops within 500 meters of maternal residence, specific dates of pregnancy, and chemical application dates based on the planting/harvesting dates of each crop. Logistic regression was used to estimate odds ratios (OR) and 95% confidence intervals (CI) for four categories of exposure (90th percentiles) compared to unexposed. Models were adjusted for maternal race, age at delivery, education, marital status, and smoking status. We observed elevated ORs for congenital heart defects and certain structural defects affecting the gastrointestinal, genitourinary and musculoskeletal systems (e.g., OR (95% CI) (highest exposure vs. unexposed) for tracheal esophageal fistula/esophageal atresia = 1.98 (0.69, 5.66), and OR for atr

Interface effects on calculated defect levels for oxide defects

NASA Astrophysics Data System (ADS)

Edwards, Arthur; Barnaby, Hugh; Schultz, Peter; Pineda, Andrew

2014-03-01

Density functional theory (DFT) has had impressive recent success predicting defect levels in insulators and semiconductors [Schultz and von Lillienfeld, 2009]. Such success requires care in accounting for long-range electrostatic effects. Recently, Komsa and Pasquarello have started to address this problem in systems with interfaces. We report a multiscale technique for calculating electrostatic energies for charged defects in oxide of the metal-oxide-silicon (MOS) system, but where account is taken of substrate doping density, oxide thickness, and gate bias. We use device modeling to calculate electric fields for a point charge a fixed distance from the interface, and used the field to numerically calculate the long-range electrostatic interactions. We find, for example, that defect levels in the oxide do depend on both the magnitude and the polarity the substrate doping density. Furthermore, below 20 Å, oxide thickness also has significant effects. So, transferring results directly from bulk calculations leads to inaccuracies up to 0.5 eV- half of the silicon band gap. We will present trends in defect levels as a function of device parameters. We show that these results explain previous experimental results, and we comment on their potential impact on models for NBTI. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the United States Department of Energy's National Nuclear Security Administration under co.

Take a byte out of MEEF: VAMPIRE: Vehicle for Advanced Mask Pattern Inspection Readiness Evaluations

NASA Astrophysics Data System (ADS)

Badger, Karen D.; Rankin, Jed; Turley, Christina; Seki, Kazunori; Dechene, Dan J.; Abdelghany, Hesham

2016-09-01

MEEF, or Mask Error Enhancement Factor, is simply defined as the ratio of the change in printed wafer feature width to the change in mask feature width scaled to wafer level. It is important in chip manufacturing that leads to the amplification of mask errors, creating challenges with both achieving dimensional control tolerances and ensuring defect free masks, as measured by on-wafer image quality. As lithographic imaging continues to be stressed, using lower and lower k1 factor resolution enhancement techniques, the high MEEF areas present on advanced optical masks creates an environment where the need for increased mask defect sensitivity in high-MEEF areas becomes more and more critical. There are multiple approaches to mask inspection that may or may not provide enough sensitivity to detect all wafer-printable defects; the challenge in the application of these techniques is simultaneously maintaining an acceptable level of mask inspectability. The higher the MEEF, the harder the challenge will be to achieve and appropriate level of sensitivity while maintaining inspectability…and to do so on the geometries that matter. The predominant photomask fabrication inspection approach in use today compares the features on the reticle directly with the design database using high-NA optics. This approach has the ability to detect small defects, however, when inspecting aggressive OPC, it can lead to the over-detection of inconsequential, or nuisance defects. To minimize these nuisance detections, changing the sensitivity of the inspection can improve the inspectability of a mask inspected in high-NA mode, however, it leads to the inability to detect subtle, yet wafer-printable defects in High-MEEF geometry, due to the fact that this `desense' must be applied globally. There are also `lithography-emulating' approaches to inspection that use various means to provide high defect sensitivity and the ability to tolerate inconsequential, non-printing defects by using scanner-like conditions to determine which defects are wafer printable. This inspection technique is commonly referred to as being `lithography plane' or `litho plane,' since it's assessing the mask quality based on how the mask appears to the imaging optics during use, as proposed to traditional `reticle plane' inspection which is comparing the mask only with its target design. Regardless of how the defects are detected, the real question is when should they be detected? For larger technology nodes, defects are considered `statistical risks'…i.e., first they have to occur, and then they have to fall in high-MEEF areas in order to be of concern, and be below the detection limits of traditional reticle-plane inspection. In short, the `perfect storm' has to happen in order to miss printable defects using well-optimized traditional inspection approaches. The introduction of lithographic inspection techniques has revealed this statistical game is a much higher risk than originally estimated, in that very subtle waferprintable CD errors typically fall into the desense band for traditional reticle plane inspection. Because printability is largely influenced by MEEF, designs with high-MEEF values are at greater risk of traditional inspection missing printable CD errors. The question is… how high is high… and at what MEEF is optical inspection at the reticle plane sufficient? This paper will provide evaluation results for both reticle-plane and litho-plane inspections as they pertain to varying degrees of MEEF. A newly designed high-MEEF programmed defect test mask, named VAMPIRE, will be introduced. This test mask is based on 7 nm node technology and contains intentionally varying degrees of MEEF as well as a variety of programmed defects in high-MEEF environments…all of which have been verified for defect lithographic significance on a Zeiss AIMS system.

Increasing reticle inspection efficiency and reducing wafer print-checks using automated defect classification and simulation

NASA Astrophysics Data System (ADS)

Ryu, Sung Jae; Lim, Sung Taek; Vacca, Anthony; Fiekowsky, Peter; Fiekowsky, Dan

2013-09-01

IC fabs inspect critical masks on a regular basis to ensure high wafer yields. These requalification inspections are costly for many reasons including the capital equipment, system maintenance, and labor costs. In addition, masks typically remain in the "requal" phase for extended, non-productive periods of time. The overall "requal" cycle time in which reticles remain non-productive is challenging to control. Shipping schedules can slip when wafer lots are put on hold until the master critical layer reticle is returned to production. Unfortunately, substituting backup critical layer reticles can significantly reduce an otherwise tightly controlled process window adversely affecting wafer yields. One major requal cycle time component is the disposition process of mask inspections containing hundreds of defects. Not only is precious non-productive time extended by reviewing hundreds of potentially yield-limiting detections, each additional classification increases the risk of manual review techniques accidentally passing real yield limiting defects. Even assuming all defects of interest are flagged by operators, how can any person's judgment be confident regarding lithographic impact of such defects? The time reticles spend away from scanners combined with potential yield loss due to lithographic uncertainty presents significant cycle time loss and increased production costs. Fortunately, a software program has been developed which automates defect classification with simulated printability measurement greatly reducing requal cycle time and improving overall disposition accuracy. This product, called ADAS (Auto Defect Analysis System), has been tested in both engineering and high-volume production environments with very successful results. In this paper, data is presented supporting significant reduction for costly wafer print checks, improved inspection area productivity, and minimized risk of misclassified yield limiting defects.

Heterogeneous Metal-Free Hydrogenation over Defect-Laden Hexagonal Boron Nitride

DOE PAGES

Nash, David J.; Restrepo, David T.; Parra, Natalia S.; ...

2016-12-21

Catalytic hydrogenation is an important process used for the production of everything from foods to fuels. Current heterogeneous implementations of this process utilize metals as the active species. Until recently, catalytic heterogeneous hydrogenation over a metal-free solid was unknown; implementation of such a system would eliminate the health, environmental, and economic concerns associated with metal-based catalysts. We report good hydrogenation rates and yields for a metal-free heterogeneous hydrogenation catalyst as well as its unique hydrogenation mechanism. We achieved catalytic hydrogenation of olefins over defect-laden h-BN (dh-BN) in a reactor designed to maximize the defects in h-BN sheets. Good yields (>90%)more » and turnover frequencies (6 × 10 –5–4 × 10 –3) were obtained for the hydrogenation of propene, cyclohexene, 1,1-diphenylethene, (E)- and (Z)-1,2-diphenylethene, octadecene, and benzylideneacetophenone. Temperature-programmed desorption of ethene over processed h-BN indicates the formation of a highly defective structure. Solid-state NMR (SSNMR) measurements of dh-BN with high and low propene surface coverages show four different binding modes. The introduction of defects into h-BN creates regions of electronic deficiency and excess. Density functional theory calculations show that both the alkene and hydrogen-bond order are reduced over four specific defects: boron substitution for nitrogen (B N), vacancies (V B and V N), and Stone–Wales defects. SSNMR and binding-energy calculations show that V N are most likely the catalytically active sites. Our work shows that catalytic sites can be introduced into a material previously thought to be catalytically inactive through the production of defects.« less

Selected birth defects among males following the United States terrorist attacks of 11 September 2001.

PubMed

Singh, Parvati; Yang, Wei; Shaw, Gary M; Catalano, Ralph; Bruckner, Tim A

2017-10-02

The terrorist attacks of 11 September 2001 (hereafter referred to as 9/11) preceded an increase in male fetal deaths and reduced male live births among exposed gestational cohorts across several geographic locations in the United States, including California. We analyze whether the extreme stressor of 9/11 may have selected against frail males in utero by testing if the prevalence of male births with selected defects in California fell among cohorts exposed to the stressor during gestation. We used data from the California Birth Defects Monitoring Program from July 1985 to January 2004 (223 conception cohorts). We included six birth defects that as a group of phenotypes disproportionately affect males. We applied time-series methods and defined as "exposed to 9/11" the cohorts conceived in February, March, April, May, June, July, and August 2001. Three of the seven monthly conception cohorts exposed to 9/11 in utero show lower than expected odds of live born males with the studied defects: February 2001 (odds ratio [OR] = 0.39; 95% confidence interval [CI], 0.21-0.71), May 2001 (OR = 0.36; 95% CI, 0.16-0.81), and August 2001 (OR = 0.51; 95% CI, 0.28-0.93). The population-wide stressor of 9/11 precedes a reduction in the risk of live born males with selected birth defects. Our analysis contributes to the understanding of adaptation to stress among pregnant women exposed to large and unexpected ambient stressors. Results further support the notion that the prevalence of live born defects may reflect temporal variation in cohort selection in utero against frail males. Birth Defects Research 109:1277-1283, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

The effects of opt-out legislation on data collection and surveillance of birth defects by the New Hampshire Birth Conditions Program, New Hampshire, United States, 2007-2009.

PubMed

Gill, Simerpal; Miller, Stephanie; Broussard, Cheryl; Reefhuis, Jennita

2012-01-01

The New Hampshire Birth Conditions Program (NHBCP) is a population-based, active case ascertainment surveillance system that monitors the occurrence of 45 birth defects across the state. A 2008 law requires a new opt-out procedure whereby legal guardians can choose whether or not to have identifiable information retained in the NHBCP database. The purpose of this study was to determine the effects of implementing this opt-out legislation on data collection and surveillance of birth defects by the NHBCP. Using surveillance data collected following implementation of the opt out legislation for the period January 1, 2007, through December 31, 2009, 2 opt-out groups were created: the identifiable information retained (IIR) group, consisting of families who did not choose to opt out, and the de-identified information retained group (DIIR), consisting of those who either chose to opt out or were treated as opt-out birth defect cases because their opt-out package was undeliverable. Descriptive statistics were calculated for each group, and chi-square or Fisher's exact tests were used to compare the proportion of select sociodemographic and medical characteristics between the 2 opt-out groups. Of 776 infants, 120 (15.5%) fell into the DIIR group. Differences were observed by race/ethnicity (among non-Hispanic whites, 15% were in the DIIR group and among Hispanics, 33% were in the DIIR group; p=0.01) and by maternal age (among women 30-34 years of age, 11% were in the DIIR group, and among those 25 years of age or younger, 22% were in the DIIR group; p=0.05). Birth outcomes, payer source, county of residence, and common birth defect diagnoses did not differ between the opt-out groups. This study demonstrated that there were significant differences in race/ethnicity and maternal age between parents who had de-identified information included in the NHBCP compared with those who did not choose to opt out. Although the surveillance of birth defects is not affected, the opportunities for certain types of research will be limited.

Restoration of Motor Defects Caused by Loss of Drosophila TDP-43 by Expression of the Voltage-Gated Calcium Channel, Cacophony, in Central Neurons.

PubMed

Lembke, Kayly M; Scudder, Charles; Morton, David B

2017-09-27

Defects in the RNA-binding protein, TDP-43, are known to cause a variety of neurodegenerative diseases, including amyotrophic lateral sclerosis and frontotemporal lobar dementia. A variety of experimental systems have shown that neurons are sensitive to TDP-43 expression levels, yet the specific functional defects resulting from TDP-43 dysregulation have not been well described. Using the Drosophila TDP-43 ortholog TBPH, we previously showed that TBPH-null animals display locomotion defects as third instar larvae. Furthermore, loss of TBPH caused a reduction in cacophony , a Type II voltage-gated calcium channel, expression and that genetically restoring cacophony in motor neurons in TBPH mutant animals was sufficient to rescue the locomotion defects. In the present study, we examined the relative contributions of neuromuscular junction physiology and the motor program to the locomotion defects and identified subsets of neurons that require cacophony expression to rescue the defects. At the neuromuscular junction, we showed mEPP amplitudes and frequency require TBPH. Cacophony expression in motor neurons rescued mEPP frequency but not mEPP amplitude. We also showed that TBPH mutants displayed reduced motor neuron bursting and coordination during crawling and restoring cacophony selectively in two pairs of cells located in the brain, the AVM001b/2b neurons, also rescued the locomotion and motor defects, but not the defects in neuromuscular junction physiology. These results suggest that the behavioral defects associated with loss of TBPH throughout the nervous system can be associated with defects in a small number of genes in a limited number of central neurons, rather than peripheral defects. SIGNIFICANCE STATEMENT TDP-43 dysfunction is a common feature in neurodegenerative diseases, including amyotrophic lateral sclerosis, frontotemporal lobar dementia, and Alzheimer's disease. Loss- and gain-of-function models have shown that neurons are sensitive to TDP-43 expression levels, but the specific defects caused by TDP-43 loss of function have not been described in detail. A Drosophila loss-of-function model displays pronounced locomotion defects that can be reversed by restoring the expression levels of a voltage-gated calcium channel, cacophony. We show these defects can be rescued by expression of cacophony in motor neurons and by expression in two pairs of neurons in the brain. These data suggest that loss of TDP-43 can disrupt the central circuitry of the CNS, opening up identification of alternative therapeutic targets for TDP-43 proteinopathies. Copyright © 2017 the authors 0270-6474/17/379486-12$15.00/0.

Engine environmental effects on composite behavior

NASA Technical Reports Server (NTRS)

Chamis, C. C.; Smith, G. T.

1980-01-01

A series of programs were conducted to investigate and develop the application of composite materials to turbojet engines. A significant part of that effort was directed to establishing the impact resistance and defect growth chracteristics of composite materials over the wide range of environmental conditions found in commercial turbojet engine operations. Both analytical and empirical efforts were involved. The experimental programs and the analytical methodology development as well as an evaluation program for the use of composite materials as fan exit guide vanes are summarized.

The Chromatin Remodeler BPTF Activates a Stemness Gene-Expression Program Essential for the Maintenance of Adult Hematopoietic Stem Cells.

PubMed

Xu, Bowen; Cai, Ling; Butler, Jason M; Chen, Dongliang; Lu, Xiongdong; Allison, David F; Lu, Rui; Rafii, Shahin; Parker, Joel S; Zheng, Deyou; Wang, Gang Greg

2018-03-13

Self-renewal and differentiation of adult stem cells are tightly regulated partly through configuration of chromatin structure by chromatin remodelers. Using knockout mice, we here demonstrate that bromodomain PHD finger transcription factor (BPTF), a component of the nucleosome remodeling factor (NURF) chromatin-remodeling complex, is essential for maintaining the population size of hematopoietic stem/progenitor cells (HSPCs), including long-term hematopoietic stem cells (HSCs). Bptf-deficient HSCs are defective in reconstituted hematopoiesis, and hematopoietic-specific knockout of Bptf caused profound defects including bone marrow failure and anemia. Genome-wide transcriptome profiling revealed that BPTF loss caused downregulation of HSC-specific gene-expression programs, which contain several master transcription factors (Meis1, Pbx1, Mn1, and Lmo2) required for HSC maintenance and self-renewal. Furthermore, we show that BPTF potentiates the chromatin accessibility of key HSC "stemness" genes. These results demonstrate an essential requirement of the chromatin remodeler BPTF and NURF for activation of "stemness" gene-expression programs and proper function of adult HSCs. Copyright © 2018 The Author(s). Published by Elsevier Inc. All rights reserved.

When does mass screening for open neural tube defects in low-risk pregnancies result in cost savings?

PubMed Central

Tosi, L L; Detsky, A S; Roye, D P; Morden, M L

1987-01-01

Using a decision analysis model, we estimated the savings that might be derived from a mass prenatal screening program aimed at detecting open neural tube defects (NTDs) in low-risk pregnancies. Our baseline analysis showed that screening v. no screening could be expected to save approximately $8 per pregnancy given a cost of $7.50 for the maternal serum alpha-feto-protein (MSAFP) test and a cost of $42,507 for hospital and rehabilitation services for the first 10 years of life for a child with spina bifida. When a more liberal estimate of the costs of caring for such a child was used, the savings with the screening program were more substantial. We performed extensive sensitivity analyses, which showed that the savings were somewhat sensitive to the cost of the MSAFP test and highly sensitive to the specificity (but not the sensitivity) of the test. A screening program for NTDs in low-risk pregnancies may result in substantial savings in direct health care costs if the screening protocol is followed rigorously and efficiently. PMID:2433011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nash, David J.; Restrepo, David T.; Parra, Natalia S.

Catalytic hydrogenation is an important process used for the production of everything from foods to fuels. Current heterogeneous implementations of this process utilize metals as the active species. Until recently, catalytic heterogeneous hydrogenation over a metal-free solid was unknown; implementation of such a system would eliminate the health, environmental, and economic concerns associated with metal-based catalysts. We report good hydrogenation rates and yields for a metal-free heterogeneous hydrogenation catalyst as well as its unique hydrogenation mechanism. We achieved catalytic hydrogenation of olefins over defect-laden h-BN (dh-BN) in a reactor designed to maximize the defects in h-BN sheets. Good yields (>90%)more » and turnover frequencies (6 × 10 –5–4 × 10 –3) were obtained for the hydrogenation of propene, cyclohexene, 1,1-diphenylethene, (E)- and (Z)-1,2-diphenylethene, octadecene, and benzylideneacetophenone. Temperature-programmed desorption of ethene over processed h-BN indicates the formation of a highly defective structure. Solid-state NMR (SSNMR) measurements of dh-BN with high and low propene surface coverages show four different binding modes. The introduction of defects into h-BN creates regions of electronic deficiency and excess. Density functional theory calculations show that both the alkene and hydrogen-bond order are reduced over four specific defects: boron substitution for nitrogen (B N), vacancies (V B and V N), and Stone–Wales defects. SSNMR and binding-energy calculations show that V N are most likely the catalytically active sites. Our work shows that catalytic sites can be introduced into a material previously thought to be catalytically inactive through the production of defects.« less

77 FR 49001 - Center for Scientific Review; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-15

...: Stem Cells, Heart Regeneration, Congenital Heart Defect and Cardiac Valve Disease. Date: September 10... Program Nos. 93.306, Comparative Medicine; 93.333, Clinical Research, 93.306, 93.333, 93.337, 93.393-93...

7 CFR 97.100 - Examination of applications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) COMMODITY LABORATORY TESTING PROGRAMS... if there are fundamental defects in the application, as determined by the examiner, the examination...

What Are the Types of Birth Defects?

MedlinePlus

... NICHD News Videos OUTREACH Safe to Sleep® National Child & Maternal Health Education Program RELATED WEBSITES NIH.gov HHS.gov USA.gov ClinicalTrials.gov WEBSITE POLICIES Disclaimer FOIA Privacy Policy Accessibility NIH...Turning Discovery Into Health ®

Loss of maintenance DNA methylation results in abnormal DNA origin firing during DNA replication.

PubMed

Haruta, Mayumi; Shimada, Midori; Nishiyama, Atsuya; Johmura, Yoshikazu; Le Tallec, Benoît; Debatisse, Michelle; Nakanishi, Makoto

2016-01-22

The mammalian maintenance methyltransferase DNMT1 [DNA (cytosine-5-)-methyltransferase 1] mediates the inheritance of the DNA methylation pattern during replication. Previous studies have shown that depletion of DNMT1 causes a severe growth defect and apoptosis in differentiated cells. However, the detailed mechanisms behind this phenomenon remain poorly understood. Here we show that conditional ablation of Dnmt1 in murine embryonic fibroblasts (MEFs) resulted in an aberrant DNA replication program showing an accumulation of late-S phase replication and causing severely defective growth. Furthermore, we found that the catalytic activity and replication focus targeting sequence of DNMT1 are required for a proper DNA replication program. Taken together, our findings suggest that the maintenance of DNA methylation by DNMT1 plays a critical role in proper regulation of DNA replication in mammalian cells. Copyright © 2015 Elsevier Inc. All rights reserved.

Comparison of standard automated perimetry with matrix frequency-doubling technology in patients with resolved optic neuritis.

PubMed

Sakai, Tsutomu; Matsushima, Masato; Shikishima, Keigo; Kitahara, Kenji

2007-05-01

To examine performance characteristics of frequency-doubling perimetry (FDP) in comparison with standard automated perimetry (SAP) in patients with resolved optic neuritis in a short-term follow-up study. Comparative consecutive case series. Twenty patients with resolved optic neuritis and 20 healthy volunteers participated in this study. The subjects were patients who recovered normal vision (1.0 or better) after optic neuritis. The Swedish interactive thresholding algorithm 30-2 program was used for SAP and a full-threshold 30-2 program was used for FDP. Using both forms of perimetry, the mean deviation (MD), pattern standard deviation (PSD), and the percentage of abnormal points significantly depressed <0.5% in the total deviation probability plot were compared. The visual fields were divided into 5 zones, and the mean sensitivity in each zone in affected eyes was compared with that in healthy eyes of the volunteers within 2 weeks of vision recovery and in follow-up after 2 weeks and 2 and 5 months. Standard automated perimetry and FDP showed general depression in the fovea and extrafoveal areas. Correlations between SAP and FDP were statistically significant for MD (Pearson r>0.75; P<0.001) and PSD (r>0.6; P<0.005). Defects detected with FDP were larger than with SAP in 14 eyes (70 %). In follow-up after 2 weeks and again after 2 and 5 months, FDP indicated slower improvement in visual field defects in the fovea and extrafoveal areas, whereas SAP indicated rapid improvement in these defects. Frequency-doubling perimetry is at least comparable with and potentially more sensitive than SAP in detecting visual field defects in resolved optic neuritis. This short-term follow-up study in patients with resolved optic neuritis suggests that FDP detects characteristics of slower recovery more effectively than SAP in the fovea and extrafoveal areas. These properties may allow more accurate detection of visual field defects and may prove advantageous for monitoring of patients with resolved optic neuritis.

Highly Efficient Defect Emission from ZnO:Zn and ZnO:S Powders

NASA Astrophysics Data System (ADS)

Everitt, Henry

2013-03-01

Bulk Zinc Oxide (ZnO) is a wide band gap semiconductor with an ultraviolet direct band gap energy of 3.4 eV and a broad, defect-related visible wavelength emission band centered near 2 eV. We have shown that the external quantum efficiency can exceed 50% for this nearly white emission band that closely matches the human dark-adapted visual response. To explore the potential of ZnO as a rare earth-free white light phosphor, we investigated the mechanism of efficient defect emission in three types of ZnO powders: unannealed, annealed, and sulfur-doped. Annealing and sulfur-doping of ZnO greatly increase the strength of defect emission while suppressing the UV band edge emission. Continuous wave and ultrafast one- and two-photon excitation spectroscopy are used to examine the defect emission mechanism. Low temperature photoluminescence (PL) and PL excitation (PLE) spectra were measured for all three compounds, and it was found that bound excitons mediate the defect emission. Temperature-dependent PLE spectra for the defect and band edge emission were measured to estimate trapping and activation energies of the bound excitons and clarify the role they play in the defect emission. Time-resolved techniques were used to ascertain the role of exciton diffusion, the effects of reabsorption, and the spatial distributions of radiative and non-radiative traps. In unannealed ZnO we find that defect emission is suppressed and UV band edge emission is inefficient (< 2%) because of reabsorption and non-radiative recombination due to a high density of non-radiative bulk traps. By annealing ZnO, bulk trap densities are reduced, and a high density of defects responsible for the broad visible emission are created near the surface. Interestingly, nearly identical PLE spectra are found for both the band edge and the defect emission, one of many indications that the defect emission is deeply connected to bound excitons. Quantum efficiency, also measured as a function of excitation wavelength, closely mirrors the PLE spectra for both emission bands. Sulfur-doped ZnO exhibits additional PLE and X-ray features indicative of a ZnS-rich surface shell that correlates with even more efficient defect emission. The results presented here offer hope that engineering defects in ZnO materials may significantly improve the quantum efficiency for white light phosphor applications. This work was supported by the Army's in-house laboratory innovative research program.

Fragile X Mental Retardation Protein is Required for Programmed Cell Death and Clearance of Developmentally-Transient Peptidergic Neurons

PubMed Central

Gatto, Cheryl L.; Broadie, Kendal

2011-01-01

Fragile X syndrome (FXS), caused by loss of fragile X mental retardation 1 (FMR1) gene function, is the most common heritable cause of intellectual disability and autism spectrum disorders. The FMR1 product (FMRP) is an RNA-binding protein best established to function in activity-dependent modulation of synaptic connections. In the Drosophila FXS disease model, loss of functionally-conserved dFMRP causes synaptic overgrowth and overelaboration in pigment dispersing factor (PDF) peptidergic neurons in the adult brain. Here, we identify a very different component of PDF neuron misregulation in dfmr1 mutants: the aberrant retention of normally developmentally-transient PDF tritocerebral (PDF-TRI) neurons. In wild-type animals, PDF-TRI neurons in the central brain undergo programmed cell death and complete, processive clearance within days of eclosion. In the absence of dFMRP, a defective apoptotic program leads to constitutive maintenance of these peptidergic neurons. We tested whether this apoptotic defect is circuit-specific by examining crustacean cardioactive peptide (CCAP) and bursicon circuits, which are similarly developmentally-transient and normally eliminated immediately post-eclosion. In dfmr1 null mutants, CCAP/bursicon neurons also exhibit significantly delayed clearance dynamics, but are subsequently eliminated from the nervous system, in contrast to the fully persistent PDF-TRI neurons. Thus, the requirement of dFMRP for the retention of transitory peptidergic neurons shows evident circuit specificity. The novel defect of impaired apoptosis and aberrant neuron persistence in the Drosophila FXS model suggests an entirely new level of “pruning” dysfunction may contribute to the FXS disease state. PMID:21596027

In situ simulated cardiac arrest exercises to detect system vulnerabilities.

PubMed

Barbeito, Atilio; Bonifacio, Alberto; Holtschneider, Mary; Segall, Noa; Schroeder, Rebecca; Mark, Jonathan

2015-06-01

Sudden cardiac arrest is the leading cause of death in the United States. Despite new therapies, progress in this area has been slow, and outcomes remain poor even in the hospital setting, where providers, drugs, and devices are readily available. This is partly attributed to the quality of resuscitation, which is an important determinant of survival for patients who experience cardiac arrest. Systems problems, such as deficiencies in the physical space or equipment design, hospital-level policies, work culture, and poor leadership and teamwork, are now known to contribute significantly to the quality of resuscitation provided. We describe an in situ simulation-based quality improvement program that was designed to continuously monitor the cardiac arrest response process for hazards and defects and to detect opportunities for system optimization. A total of 72 simulated unannounced cardiac arrest exercises were conducted between October 2010 and September 2013 at various locations throughout our medical center and at different times of the day. We detected several environmental, human-machine interface, culture, and policy hazards and defects. We used the Systems Engineering Initiative for Patient Safety (SEIPS) model to understand the structure, processes, and outcomes related to the hospital's emergency response system. Multidisciplinary solutions were crafted for each of the hazards detected, and the simulation program was used to iteratively test the redesigned processes before implementation in real clinical settings. We describe an ongoing program that uses in situ simulation to identify and mitigate latent hazards and defects in the hospital emergency response system. The SEIPS model provides a framework for describing and analyzing the structure, processes, and outcomes related to these events.

Corticosteroid therapy in patients with non-arteritic anterior ischemic optic neuropathy.

PubMed

Vidović, Tomislav; Cerovski, Branimir; Perić, Sanja; Kordić, Rajko; Mrazovac, Danijela

2015-03-01

Non-arteritic anterior ischemic optic neuropathy is one of the most common conditions affecting the optic nerve in the elderly. It may lead to severe visual loss. Typical symptoms are painless impairment of visual function accompanied by relative afferent pupillary defect, edema of the optic disc and visual field defects. Aim is to present 38 patients with nonarteritic anterior ischemic optic neuropathy who were treated with corticosteroid therapy. This prospective study involved 38 patients, 20 men and 18 women aged 60-75 years who were treated with corticosteroid therapy. The study included patients with visual acuity in the affected eye from 0.1 to 0.8 according to Snellen. Every patient underwent clinical examination, the Octopus 900 perimetry in G program, laboratory testing, while the compressive optic neuropathy was rule out with MSCT of the brain and orbits. The most common forms of visual field defect are altitudinal defect and diffuse depression. Corticosteroid therapy led to recovery in 65% of patient, in 30% of patients did not change, while the deterioration occurred in 5% of patients.

Mouse Models for Investigating the Developmental Bases of Human Birth Defects

PubMed Central

MOON, ANNE M.

2006-01-01

Clinicians and basic scientists share an interest in discovering how genetic or environmental factors interact to perturb normal development and cause birth defects and human disease. Given the complexity of such interactions, it is not surprising that 4% of human infants are born with a congenital malformation, and cardiovascular defects occur in nearly 1%. Our research is based on the fundamental hypothesis that an understanding of normal and abnormal development will permit us to generate effective strategies for both prevention and treatment of human birth defects. Animal models are invaluable in these efforts because they allow one to interrogate the genetic, molecular and cellular events that distinguish normal from abnormal development. Several features of the mouse make it a particularly powerful experimental model: it is a mammalian system with similar embryology, anatomy and physiology to humans; genes, proteins and regulatory programs are largely conserved between human and mouse; and finally, gene targeting in murine embryonic stem cells has made the mouse genome amenable to sophisticated genetic manipulation currently unavailable in any other model organism. PMID:16641221

Patent ductus arteriosus in mice with smooth muscle-specific Jag1 deletion

PubMed Central

Feng, Xuesong; Krebs, Luke T.; Gridley, Thomas

2010-01-01

The ductus arteriosus is an arterial vessel that shunts blood flow away from the lungs during fetal life, but normally occludes after birth to establish the adult circulation pattern. Failure of the ductus arteriosus to close after birth is termed patent ductus arteriosus and is one of the most common congenital heart defects. Mice with smooth muscle cell-specific deletion of Jag1, which encodes a Notch ligand, die postnatally from patent ductus arteriosus. These mice exhibit defects in contractile smooth muscle cell differentiation in the vascular wall of the ductus arteriosus and adjacent descending aorta. These defects arise through an inability to propagate the JAG1-Notch signal via lateral induction throughout the width of the vascular wall. Both heterotypic endothelial smooth muscle cell interactions and homotypic vascular smooth muscle cell interactions are required for normal patterning and differentiation of the ductus arteriosus and adjacent descending aorta. This new model for a common congenital heart defect provides novel insights into the genetic programs that underlie ductus arteriosus development and closure. PMID:21068062

Exploring the effects of defects on DT burn, the DIME experiment and measuring capsule zero-order hydrodynamics using Polar direct drive

NASA Astrophysics Data System (ADS)

Magelssen, G. R.; Bradley, P. A.; Tregillis, I. L.; Schmitt, M. J.; Dodd, E. S.; Wysocki, F. J.; Hsu, S. C.; Cobble, J.; Batha, S. H.; Defriend Obrey, K. A.

2010-11-01

Small capsule perturbations may impact our ability to achieve high yields on NIF. Diagnosing the hydrodynamic development and the effect of defects on burn will be difficult. Los Alamos is developing a program to better understand the hydrodynamics of defects and how they influence burn. Our first effort to study the effects of defects was on Omega. Both thin-shelled (exploding pusher) and thick-shelled capsules were shot and the results published [1]. In this work we add experimental shots done recently on Omega. These shots were to complete the study of how the width and depth of the defect affects DT yield. Our AMR code is used to predict the yield. Comparisons between capsule and experimental yields will be given. Experiments are also being designed for Polar direct drive. Our first experiments are being designed to understand the zero-order hydrodynamics with Polar direct drive. Capsules about a millimeter in radius are being designed with one to two dopants in the CH shell for radiograph and MMI usage. Also, to minimize the effect of mix on the radius versus time trajectory, some capsules will replace the DT with Xe.[0pt] [1] Magelssen G. R. et al., to be published in the 2009 IFSA proceedings.

Design of an aid to visual inspection workstation

NASA Astrophysics Data System (ADS)

Tait, Robert; Harding, Kevin

2016-05-01

Visual Inspection is the most common means for inspecting manufactured parts for random defects such as pits, scratches, breaks, corrosion or general wear. The reason for the need for visual inspection is the very random nature of what might be a defect. Some defects may be very rare, being seen once or twice a year, but May still be critical to part performance. Because of this random and rare nature, even the most sophisticated image analysis programs have not been able to recognize all possible defects. Key to any future automation of inspection is obtaining good sample images of what might be a defect. However, most visual check take no images and consequently generate no digital data or historical record beyond a simple count. Any additional tool to captures such images must be able to do so without taking addition time. This paper outlines the design of a potential visual inspection station that would be compatible with current visual inspection methods, but afford the means for reliable digital imaging and in many cases augmented capabilities to assist the inspection. Considerations in this study included: resolution, depth of field, feature highlighting, and ease of digital capture, annotations and inspection augmentation for repeatable registration as well as operator assistance and training.

Engineering the Mechanical Properties of Polymer Networks with Precise Doping of Primary Defects.

PubMed

Chan, Doreen; Ding, Yichuan; Dauskardt, Reinhold H; Appel, Eric A

2017-12-06

Polymer networks are extensively utilized across numerous applications ranging from commodity superabsorbent polymers and coatings to high-performance microelectronics and biomaterials. For many applications, desirable properties are known; however, achieving them has been challenging. Additionally, the accurate prediction of elastic modulus has been a long-standing difficulty owing to the presence of loops. By tuning the prepolymer formulation through precise doping of monomers, specific primary network defects can be programmed into an elastomeric scaffold, without alteration of their resulting chemistry. The addition of these monomers that respond mechanically as primary defects is used both to understand their impact on the resulting mechanical properties of the materials and as a method to engineer the mechanical properties. Indeed, these materials exhibit identical bulk and surface chemistry, yet vastly different mechanical properties. Further, we have adapted the real elastic network theory (RENT) to the case of primary defects in the absence of loops, thus providing new insights into the mechanism for material strength and failure in polymer networks arising from primary network defects, and to accurately predict the elastic modulus of the polymer system. The versatility of the approach we describe and the fundamental knowledge gained from this study can lead to new advancements in the development of novel materials with precisely defined and predictable chemical, physical, and mechanical properties.

The relationship between the retinal image quality and the refractive index of defects arising in IOL: numerical analysis

NASA Astrophysics Data System (ADS)

Geniusz, Malwina

2017-09-01

The best treatment for cataract patients, which allows to restore clear vision is implanting an artificial intraocular lens (IOL). The image quality of the lens has a significant impact on the quality of patient's vision. After a long exposure the implant to aqueous environment some defects appear in the artificial lenses. The defects generated in the IOL have different refractive indices. For example, glistening phenomenon is based on light scattering on the oval microvacuoles filled with an aqueous humor which refractive index value is about 1.34. Calcium deposits are another example of lens defects and they can be characterized by the refractive index 1.63. In the presented studies it was calculated how the difference between the refractive indices of the defect and the refractive index of the lens material affects the quality of image. The OpticStudio Professional program (from Radiant Zemax, LLC) was used for the construction of the numerical model of the eye with IOL and to calculate the characteristics of the retinal image. Retinal image quality was described in such characteristics as Point Spread Function (PSF) and the Optical Transfer Function with amplitude and phase. The results show a strong correlation between the refractive indices difference and retinal image quality.

48 CFR 2115.402 - Policy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... NEGOTIATION Contract Pricing 2115.402 Policy. Pricing of FEGLI Program premium rates is governed by 5 U.S.C... for pricing, such estimates will be deemed acceptable and, if inaccurate, will not constitute defective pricing. [70 FR 41151, July 18, 2005] ...

METROPOLITAN ATLANTA DEVELOPMENTAL DISABILITIES PROGRAM (MADDSP)

EPA Science Inventory

To address the problem of developmental disabilities among children, CDC, the former Division of Birth Defects and Developmental Disabilities, which was funded by the Agency for Toxic Substances and Disease Registry (ATSDR), and the Georgia Department of Human Resources, initiate...

Device Performance and Reliability Improvements of AlGaN/GaN/Si MOSFET Using Defect-Free Gate Recess and Laser Annealing

DTIC Science & Technology

2015-02-15

currently valid OMB control number . PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) 20-04-2015 2. REPORT TYPE...of AlGaN/GaN/Si MOSFET Using Defect-Free Gate Recess and Laser Annealing 5a. CONTRACT NUMBER FA2386-11-1-4077 5b. GRANT NUMBER Grant AOARD...114077 5c. PROGRAM ELEMENT NUMBER 61102F 6. AUTHOR(S) Prof. Robert Wallace 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7

How voluntary prenatal diagnosis and selective abortion increase the abnormal human gene pool.

PubMed

Boss, J A

1990-06-01

It is often assumed that prenatal diagnosis followed by the selective abortion of "defective" fetuses has a positive eugenic effect. Although mandatory selective abortion of "defective" fetuses and, more important, carriers would tend to reduce the number of deleterious genes in the gene pool, the present program of voluntary prenatal diagnosis and selective abortion actually increases the number of deleterious genes. This raises the issue of freedom of choice regarding selective abortion and societal pressure on parents to undergo prenatal testing and to abort their fetus should it have a genetic disorder or be a carrier of one.

Electrical and mechanical tuning of a silicon vacancy defect in SiC for quantum information technology

NASA Astrophysics Data System (ADS)

Soykal, Oney O.; Reinecke, Thomas L.

We develop coherent control via Stark effect over the optical transition energies of silicon monovacancy deep center in hexagonal silicon carbide. We show that this defect's unique asymmetry properties of its piezoelectric tensor and Kramer's degenerate high-spin ground/excited state configurations can be used to create new possibilities in quantum information technology ranging from photonic networks to quantum key distribution. We also give examples of its qubit implementations via precise electric field control. This work was supported in part by ONR and by the Office of Secretary of Defense, Quantum Science and Engineering Program.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konyashov, Vadim V.; Krasnov, Alexander M.

Results are provided of the experimental investigation of radioactive fission product (RFP) release, i.e., krypton, xenon, and iodine radionuclides from fuel elements with initial defects during long-term (3 to 5 yr) irradiation under low linear power (5 to 12 kW/m) and during special experiments in the VK-50 vessel-type boiling water reactor.The calculation model for the RFP release from the fuel-to-cladding gap of the defective fuel element into coolant was developed. It takes into account the convective transport in the fuel-to-cladding gap and RFP sorption on the internal cladding surface and is in good agreement with the available experimental data. Anmore » approximate analytical solution of the transport equation is given. The calculation dependencies of the RFP release coefficients on the main parameters such as defect size, fuel-to-cladding gap, temperature of the internal cladding surface, and radioactive decay constant were analyzed.It is shown that the change of the RFP release from the fuel elements with the initial defects during long-term irradiation is, mainly, caused by fuel swelling followed by reduction of the fuel-to-cladding gap and the fuel temperature. The calculation model for the RFP release from defective fuel elements applicable to light water reactors (LWRs) was developed. It takes into account the change of the defective fuel element parameters during long-term irradiation. The calculation error according to the program does not exceed 30% over all the linear power change range of the LWR fuel elements (from 5 to 26 kW/m)« less

The assessment of orthodontic bonding defects: optical coherence tomography followed by three-dimensional reconstruction

NASA Astrophysics Data System (ADS)

Rominu, R.; Sinescu, C.; Rominu, M.; Negrutiu, M.; Petrescu, E.; Pop, D.; Podoleanu, A. Gh.

2011-10-01

Orthodontic bonding is a simple yet important procedure that can influence the outcome of treatment in case it is performed incorrectly. An orthodontic treatment shadowed by repeated bonding failures can become unduly long and will decrease patient trust and compliance. Optical coherence tomography has been widely used in ophtalmology but is relatively new to dentistry. Using OCT one can detect aerial inclusions within the orthodontic adhesive or even identify incongruence between the bracket base and the tooth surface. The aim of our study was to identify bonding defects and reconstruct them three-dimensionally in order to be able to characterize them more accurately. We bonded 30 sound human permanent teeth with ceramic orthodontic brackets using a no-mix self-curing orthodontic adhesive. Prior to bonding all teeth were stored in tap water at 4°C and then professionally cleaned with rotary brushes and pumice. The samples were processed by the same person and the rotary brushes were changed after every fifth tooth. All interfaces were investigated by means of OCT and 4 defects were found. Subsequently, the defects were reconstructed threedimensionally using an open-source program. By identifying and reconstructing bonding defects we could assess the quality of the bonding procedure. Since bonding tends to be more accurate in vitro where the environmental conditions are close to ideal, it is probable that defects found in vivo be even greater in number, which leads to the conclusion that this type of investigation is potentially valuable.

Thin-film reliability and engineering overview

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.

1984-01-01

The reliability and engineering technology base required for thin film solar energy conversions modules is discussed. The emphasis is on the integration of amorphous silicon cells into power modules. The effort is being coordinated with SERI's thin film cell research activities as part of DOE's Amorphous Silicon Program. Program concentration is on temperature humidity reliability research, glass breaking strength research, point defect system analysis, hot spot heating assessment, and electrical measurements technology.

Thin-film reliability and engineering overview

NASA Astrophysics Data System (ADS)

Ross, R. G., Jr.

1984-10-01

The reliability and engineering technology base required for thin film solar energy conversions modules is discussed. The emphasis is on the integration of amorphous silicon cells into power modules. The effort is being coordinated with SERI's thin film cell research activities as part of DOE's Amorphous Silicon Program. Program concentration is on temperature humidity reliability research, glass breaking strength research, point defect system analysis, hot spot heating assessment, and electrical measurements technology.

Great Institutions in Cardiothoracic Surgery: The University of Minnesota.

PubMed

Huddleston, Stephen J; Shumway, Sara

2016-01-01

With the loyal support of the chair of Surgery, Dr. Owen H. Wangensteen, the University of Minnesota cardiac surgery program led the way at the dawn of cardiac surgery when Dr F. John Lewis performed the first open heart surgery in the world using hypothermia while repairing an atrial septal defect on September 2, 1952. Soon after, Dr C. Walt Lillehei performed the first repair of a ventriculoseptal defect in the world using cross-circulation on March 26, 1954. Collaborating with Dr Richard DeWall in 1955, they developed the DeWall-Lillehei bubble oxygentor which was used at the University of Minnesota and many other centers worldwide for years to come, making open heart surgery safe and tractable. Dr Vincent Gott, a resident working in the laboratory of Lillehei, developed a method to treat complete heart block using ventricular pacing with a Grass physiological stimulator, and this led to a collaboration with Earl Bakken, founder of the Medtronic Corporation, to develop a temporary pacemaker. The program was fertile ground for many notable trainees, including Dr Norman Shumway, the "Father of Heart Transplant", and Dr Christiaan Barnard who performed the first heart transplant in the world. The collegial and forward thinking nature of the cardiac surgery program continues in the current training program today. Copyright © 2016 Elsevier Inc. All rights reserved.

Quantitative determination of anti-structured defects applied to alloys of a wide chemical range

NASA Astrophysics Data System (ADS)

Zhang, Jing; Chen, Zheng; Wang, Yongxin; Lu, Yanli

2016-11-01

Anti-structured defects bridge atom migration among heterogeneous sublattices facilitating diffusion but could also result in the collapse of ordered structure. Component distribution Ni75Al x V25-x alloys are investigated using a microscopic phase field model to illuminate relations between anti-structured defects and composition, precipitate order, precipitate type, and phase stability. The Ni75Al x V25-x alloys undergo single Ni3V (stage I), dual Ni3Al and Ni3V (stage II with Ni3V prior; and stage III with Ni3Al prior), and single Ni3Al (stage IV) with enhanced aluminum level. For Ni3V phase, anti-structured defects (VNi1, NiV, except VNi2) and substitution defects (AlNi1, AlNi2, AlV) exhibit a positive correlation to aluminum in stage I, the positive trend becomes to negative correlation or smooth during stage II. For Ni3Al phase, anti-structured defects (AlNi, NiAl) and substitution defects (VNi, VAl) have a positive correlation to aluminum in stage II, but NiAl goes down since stage III and lasts to stage IV. VNi and VAl fluctuate when Ni3Al precipitates prior, but go down drastically in stage IV. Precipitate type conversion of single Ni3V/dual (Ni3V+Ni3Al) affects Ni3V defects, while dual (Ni3V+Ni3Al)/single Ni3Al has little effect on Ni3Al defects. Precipitate order swap occurred in the dual phase region affects on Ni3Al defects but not on Ni3V. Project supported by the Natural Science Basic Research Plan in Shaanxi Province of China (Grant No. 2016JQ5014), the Fundamental Research Funds for the Central Universities, China (Grant No. 3102014JCQ01024), the Research Fund of the State Key Laboratory of Solidification Processing (NWPU), China (Grant No. 114-QP-2014), the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20136102120021), and the National Natural Science Foundation of China (Grant Nos. 51474716 and 51475378).

Digital volume tomography in the diagnosis of periodontal defects: an in vitro study on native pig and human mandibles.

PubMed

Mengel, Reiner; Candir, Muhsin; Shiratori, Kiyoshi; Flores-de-Jacoby, Lavin

2005-05-01

The aim of this study of native pig and human mandibles was to investigate the accuracy and quality of the representation of periodontal defects by intraoral radiography (IR), panoramic radiography (PR), computed tomography (CT), and digital volume tomography (DVT) in comparison with histologic specimens. Following the standardized preparation of periodontal defects (14 dehiscences, fenestrations, 2- to 3-walled intrabony defects, respectively; Class I, II, and III furcation involvement) in six pig and seven human mandibles, IR, PR, CT, and DVT were performed. The histologic specimens were produced by cutting blocks with the individual defects out of the mandibles, embedding them in acrylic, and producing sagittal and axial microsections. The intrabony defects were measured using appropriate software on the digitized IR and PR images programs. The histologic sections were measured by reflecting stereomicroscopy. The statistical comparison between the measurements of the radiographic images and those of the histologic specimens was performed with Pearson's correlation coefficient. The quality of the radiographic images was determined through the subjective perception and detectability of the intrabony defects by five independent observers. All intrabony defects could be measured in three planes in the CT and DVT scans. Comparison with the histologic specimens yielded a mean deviation of 0.16 +/- 0.10 mm for the CT scans and 0.19 +/- 0.11 mm for the DVT scans. On the IR and PR images, the defects could be detected only in the mesio-distal and craniocaudal planes. In comparison with the histologic specimens, the IR images revealed a mean deviation of 0.33 +/- 0.18 mm and the PR images a mean deviation of 1.07 +/- 0.62 mm. The quality rating of the radiographic images was highest for the DVT scans. Overall, the CT and DVT scans displayed only a slight deviation in the extent of the periodontal defects in comparison with the histologic specimens. Both radiographic imaging techniques permitted imaging of anatomic osseous structures in three planes, true to scale, and without overlay or distortion. The DVT scans showed the best imaging quality.

Silicon Carbide Epitaxial Films Studied by Atomic Force Microscopy

NASA Technical Reports Server (NTRS)

1996-01-01

Silicon carbide (SiC) holds great potential as an electronic material because of its wide band gap energy, high breakdown electric field, thermal stability, and resistance to radiation damage. Possible aerospace applications of high-temperature, high-power, or high-radiation SiC electronic devices include sensors, control electronics, and power electronics that can operate at temperatures up to 600 C and beyond. Commercially available SiC devices now include blue light-emitting diodes (LED's) and high-voltage diodes for operation up to 350 C, with other devices under development. At present, morphological defects in epitaxially grown SiC films limit their use in device applications. Research geared toward reducing the number of structural inhomogeneities can benefit from an understanding of the type and nature of problems that cause defects. The Atomic Force Microscope (AFM) has proven to be a useful tool in characterizing defects present on the surface of SiC epitaxial films. The in-house High-Temperature Integrated Electronics and Sensors (HTIES) Program at the NASA Lewis Research Center not only extended the dopant concentration range achievable in epitaxial SiC films, but it reduced the concentration of some types of defects. Advanced structural characterization using the AFM was warranted to identify the type and structure of the remaining film defects and morphological inhomogeneities. The AFM can give quantitative information on surface topography down to molecular scales. Acquired, in part, in support of the Advanced High Temperature Engine Materials Technology Program (HITEMP), the AFM had been used previously to detect partial fiber debonding in composite material cross sections. Atomic force microscopy examination of epitaxial SiC film surfaces revealed molecular-scale details of some unwanted surface features. Growth pits propagating from defects in the substrate, and hillocks due, presumably, to existing screw dislocations in the substrates, were imaged. Away from local defects, step bunching was observed to yield step heights of hundreds of angstroms, with possible implications for the uniformity of dopants incorporated in SiC devices during fabrication. The quantitative topographic data from the AFM allow the relevant defect information to be extracted, such as the size and distribution of step bunching and the Burgers vector of screw dislocations. These atomic force microscopy results have furthered the understanding of the dynamic epitaxial SiC growth process. A model describing the observed hillock step bunching has been proposed. This cooperation between researchers involved in crystal growth, electronic device fabrication, and surface structural characterization is likely to continue as atomic force microscopy is used to improve SiC films for high-temperature electronic devices for NASA's advanced turbine engines and space power devices, as well as for future applications in the automotive industry.

Parametric study using modal analysis of a bi-material plate with defects

NASA Astrophysics Data System (ADS)

Esola, S.; Bartoli, I.; Horner, S. E.; Zheng, J. Q.; Kontsos, A.

2015-03-01

Global vibrational method feasibility as a non-destructive inspection tool for multi-layered composites is evaluated using a simulated parametric study approach. A finite element model of a composite consisting of two, isotropic layers of dissimilar materials and a third, thin isotropic layer of adhesive is constructed as the representative test subject. Next, artificial damage is inserted according to systematic variations of the defect morphology parameters. A free-vibrational modal analysis simulation is executed for pristine and damaged plate conditions. Finally, resultant mode shapes and natural frequencies are extracted, compared and analyzed for trends. Though other defect types may be explored, the focus of this research is on interfacial delamination and its effects on the global, free-vibrational behavior of a composite plate. This study is part of a multi-year research effort conducted for the U.S. Army Program Executive Office - Soldier.

Strategy For Yield Control And Enhancement In VLSI Wafer Manufacturing

NASA Astrophysics Data System (ADS)

Neilson, B.; Rickey, D.; Bane, R. P.

1988-01-01

In most fully utilized integrated circuit (IC) production facilities, profit is very closely linked with yield. In even the most controlled manufacturing environments, defects due to foreign material are a still major contributor to yield loss. Ideally, an IC manufacturer will have ample engineering resources to address any problem that arises. In the real world, staffing limitations require that some tasks must be left undone and potential benefits left unrealized. Therefore, it is important to prioritize problems in a manner that will give the maximum benefit to the manufacturer. When offered a smorgasbord of problems to solve, most people (engineers included) will start with what is most interesting or the most comfortable to work on. By providing a system that accurately predicts the impact of a wide variety of defect types, a rational method of prioritizing engineering effort can be made. To that effect, a program was developed to determine and rank the major yield detractors in a mixed analog/digital FET manufacturing line. The two classical methods of determining yield detractors are chip failure analysis and defect monitoring on drop in test die. Both of these methods have short comings: 1) Chip failure analysis is painstaking and very time consuming. As a result, the sample size is very small. 2) Drop in test die are usually designed for device parametric analysis rather than defect analysis. To provide enough wafer real estate to do meaningful defect analysis would render the wafer worthless for production. To avoid these problems, a defect monitor was designed that provided enough area to detect defects at the same rate or better than the NMOS product die whose yield was to be optimized. The defect monitor was comprehensive and electrically testable using such equipment as the Prometrix LM25 and other digital testers. This enabled the quick accumulation of data which could be handled statistically and mapped individually. By scaling the defect densities found on the monitors to the known sensitivities of the product wafer, the defect types were ranked by defect limiting yield. (Limiting yield is the resultant product yield if there were no other failure mechanisms other than the type being considered.) These results were then compared to the product failure analysis results to verify that the monitor was finding the same types of defects in the same proportion which were troubling our product. Finally, the major defect types were isolated and reduced using the short loop capability of the monitor.

38 CFR 21.8286 - Training resources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Training resources. 21...) VOCATIONAL REHABILITATION AND EDUCATION Vocational Training and Rehabilitation for Certain Children of Vietnam Veterans-Spina Bifida and Covered Birth Defects Vocational Training Program Entrance, Termination...

Genotypes are useful for more than genomic evaluation

USDA-ARS?s Scientific Manuscript database

New services that provide pedigree discovery, breed composition, mating programs, genomic inbreeding, fertility defects, and inheritance tracking all are possible from low-cost genotyping in addition to genomic evaluation. Genetic markers let breeders select among sibs before their phenotypes became...

Small Portable Analyzer Diagnostic Equipment (SPADE) Program -- Diagnostic Software Validation

DTIC Science & Technology

1984-07-01

Electronic Equipment Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference Electromagnetic...ONLY. ORIENTATION OF DEFECT LOOKING HHO QIlILL: t -ed’-o· Significant efforts were expended to simulate spalling failures associated with naturally

7 CFR 1924.259 - Handling dwelling construction complaints.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Handling dwelling construction complaints. 1924.259... OF AGRICULTURE PROGRAM REGULATIONS CONSTRUCTION AND REPAIR Complaints and Compensation for Construction Defects § 1924.259 Handling dwelling construction complaints. This section describes the procedure...

40 CFR 85.1901 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Applicability. 85.1901 Section 85.1901 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1901 Applicability. The...

WaveOne Rotary Instruments after Clinical Use.

PubMed

Shen, Ya; Coil, Jeffrey M; Mo, Anthony John; Wang, Zhejun; Hieawy, Ahmed; Yang, Yan; Haapasalo, Markus

2016-02-01

The purpose of this study was to evaluate the incidence and mode of WaveOne (Dentsply Tulsa Dental Specialties, Tulsa, OK) instrument defects after single use at different endodontic clinics. A total of 438 WaveOne instruments were collected after clinical use from the 4 specialist clinics over a 12-month period and from 1 graduate program over a 20-month period. The incidence and type of instrument defects were analyzed. The lateral surfaces of part of the defective instruments and fracture surfaces of fractured files were examined using scanning electron microscopy. Unused and clinically used files were examined by a nanoindentation test. Of the 438 WaveOne instruments collected, 42 (9.6%) had defects: 40 (9.1%) were distorted and 2 (0.5%) files had fractured, 1 Small and 1 Primary file. Clear differences in the frequency of defects were found among the 3 file sizes; the occurrence of distortion and fracture were highest with the Small file (21.2% and 0.7%, respectively) followed by the Primary file (4.4% and 0.4%, respectively) (P < .05). No defects were detected on the Large file. The cause of the 2 fractures was shear stress. Instruments from various clinics showed no significantly different occurrence of instrument deformation. Unwinding occurred at 1.2-3.1 mm from the tip. No significant difference in nanohardness was detected among unused and used instruments. The risk of WaveOne fracture is very low when files are singly used by endodontists and residents. Unwinding of the files occurred most frequently in the Small file. The frequency of defects of WaveOne instruments were not influenced by the operator. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Validation of birth outcomes from the Society for Assisted Reproductive Technology Clinic Outcome Reporting System (SART CORS): population-based analysis from the Massachusetts Outcome Study of Assisted Reproductive Technology (MOSART).

PubMed

Stern, Judy E; Gopal, Daksha; Liberman, Rebecca F; Anderka, Marlene; Kotelchuck, Milton; Luke, Barbara

2016-09-01

To assess the validity of outcome data reported to the Society for Assisted Reproductive Technology Clinic Outcome Reporting System (SART CORS) compared with data from vital records and the birth defects registry in Massachusetts. Longitudinal cohort. Not applicable. A total of 342,035 live births and fetal deaths from Massachusetts mothers giving birth in the state from July 1, 2004, to December 31, 2008; 9,092 births and fetal deaths were from mothers who had conceived with the use of assisted reproductive technology (ART) and whose cycle data had been reported to the SART CORS. Not applicable. Percentage agreement between maternal race and ethnicity, delivery outcome (live birth or fetal death), plurality (singleton, twin, or triplet+), delivery date, and singleton birth weight reported in the SART CORS versus vital records; sensitivity and specificity for birth defects among singletons as reported in the SART CORS versus the Massachusetts Birth Defects Monitoring Program (BDMP). There was >95% agreement between the SART CORS and vital records for fields of maternal race/ethnicity, live birth/fetal death, and plurality; birth outcome date was within 1 day with 94.9% agreement and birth weight was within 100 g with 89.6% agreement. In contrast, sensitivity for report of any birth defect was 38.6%, with a range of 18.4%-50.0%, for specific birth defect categories. Although most SART CORS outcome fields are accurately reported, birth defect variables showed poor sensitivity compared with the gold standard data from the BDMP. We suggest that reporting of birth defects be discontinued. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

The influence of artificial scotomas on eye movements during visual search.

PubMed

Cornelissen, Frans W; Bruin, Klaas J; Kooijman, Aart C

2005-01-01

Fixation durations are normally adapted to the difficulty of the foveal analysis task. We examine to what extent artificial central and peripheral visual field defects interfere with this adaptation process. Subjects performed a visual search task while their eye movements were registered. The latter were used to drive a real-time gaze-dependent display that was used to create artificial central and peripheral visual field defects. Recorded eye movements were used to determine saccadic amplitude, number of fixations, fixation durations, return saccades, and changes in saccade direction. For central defects, although fixation duration increased with the size of the absolute central scotoma, this increase was too small to keep recognition performance optimal, evident from an associated increase in the rate of return saccades. Providing a relatively small amount of visual information in the central scotoma did substantially reduce subjects' search times but not their fixation durations. Surprisingly, reducing the size of the tunnel also prolonged fixation duration for peripheral defects. This manipulation also decreased the rate of return saccades, suggesting that the fixations were prolonged beyond the duration required by the foveal task. Although we find that adaptation of fixation duration to task difficulty clearly occurs in the presence of artificial scotomas, we also find that such field defects may render the adaptation suboptimal for the task at hand. Thus, visual field defects may not only hinder vision by limiting what the subject sees of the environment but also by limiting the visual system's ability to program efficient eye movements. We speculate this is because of how visual field defects bias the balance between saccade generation and fixation stabilization.

Microdefects and self-interstitial diffusion in crystalline silicon

NASA Astrophysics Data System (ADS)

Knowlton, William Barthelemy

In this thesis, a study is presented of D-defects and self-interstitial diffusion in silicon using Li ion (Lisp+) drifting in an electric field and transmission electron microscopy (TEM). Obstruction of Lisp+ drifting has been found in wafers from certain but not all FZ p-type Si. Incomplete Lisp+ drifting always occurs in the central region of the wafers. This work established that interstitial oxygen is not responsible for hindering Lisp+ drifting. The Osb i concentration was measured ({˜}2× 10sp{15}\\ cmsp{-3}) by local vibrational mode Fourier transform infrared spectroscopy and did not vary radially across the wafer. TEM was performed on a samples from the partially Lisp+ drifted area and compared to regions without D-defects. Precipitates were found only in the region containing D-defects that had partially Lisp+ drifted. This result indicates D-defects are responsible for the precipitation that halts the Lisp+ drift process. The precipitates were characterized using selected area diffraction (SAD) and image contrast analysis. The results suggested that the precipitates may cause stacking faults and their identity may be lithium silicides such as Lisb{21}Sisb5\\ and\\ Lisb{13}Sisb4. TEM revealed a decreasing distribution of Li precipitates as a function of Lisp+ drift depth along the growth direction. A preliminary model is presented that simulates Lisp+ drifting. The objective of the model is to incorporate the Li precipitate density distribution and Lisp+ drift depth to extract the size and capture cross-section of the D-defects. Nitrogen (N) doping has been shown to eliminate D-defects as measured by conventional techniques. However, Lisp+ drifting has shown that D-defects are indeed still present. Lisp+ drifting is able to detect D-defects at concentrations lower than conventional techniques. Lisp+ drifting and D-defects provide a useful means to study Si self-interstitial diffusion. The process modeling program SUPREM-IV was used to simulate the results of Si self-interstitial diffusion obtained from Lisp+ drifting experiments. Anomalous results from the Si self-interstitial diffusion experiments forced a re-examination of the possibility of thermal dissociation of D-defects. Thermal annealing experiments that were performed support this possibility. A review of the current literature illustrates the need for more research on the effects of thermal processing on FZ Si to understand the dissolution kinetics of D-defects.

Experimental investigation of defect criticality in FRP laminate composites

NASA Astrophysics Data System (ADS)

Joyce, Peter James

1999-11-01

This work examines the defect criticality of fiber reinforced polymer Composites. The objective is to determine the sensitivity of the finished composite to various process-induced defects. This work focuses on two different classes of process-induced defects; (1) fiber waviness in high performance carbon-fiber reinforced unidirectional composites and (2) void volume in low cost glass-fabric reinforced composites. The role of fiber waviness in the compressive response of unidirectional composites has been studied by a number of other investigators. Because of difficulties associated with producing real composites with varying levels of fiber waviness, most experimental studies of fiber waviness have evaluated composites with artificially induced fiber waviness. Furthermore, most experimental studies have been concentrated on the effects of out-of-plane fiber waviness. The objective of this work is to evaluate the effects of in-plane fiber waviness naturally occurring in autoclave consolidated thermoplastic laminates. The first phase of this project involved the development of a simple technique for measuring the resulting fiber waviness levels. An experimental investigation of the compression strength reduction in composites with in-plane fiber waviness followed. The experimental program included carbon-fiber reinforced thermoplastic composites manufactured from prepreg tape by hand layup, and carbon-fiber and glass-fiber reinforced composites manufactured from an experimental powder towpreg by filament winding and autoclave consolidation. The compression specimens exhibited kink band failure in the prepreg composite and varying amounts of longitudinal splitting and kink banding in the towpreg composites. The compression test results demonstrated the same trend as predicted by microbudding theory but the overall quantitative correlation was poor. The second thrust of this research evaluated void effects in resin transfer molded composites. Much of the existing literature in this area has focused on composites with unidirectional fiber reinforcement. In this program, the influence of void volume on the mechanical behavior of RTM composites with plain weave reinforcement was investigated. The experimental program demonstrated that the effects of void volume are negligible in terms of the fiber dominated properties. Interlaminar shear strength tests on the other hand demonstrated a linear dependence on void volume in the range tested.

Effectiveness of spacecraft testing programs

NASA Technical Reports Server (NTRS)

Krausz, A.

1980-01-01

The need for testing under simulated mission operational conditions is discussed and the results of such tests are reviewed from the point of view of the user. A brief overview of the usal test sequences for high reliability long life spacecraft is presented and the effectiveness of the testing program is analyzed in terms of the defects which are discovered by such tests. The need for automation, innovative mechanical test procedures, and design for testability is discussed.

40 CFR 92.404 - Voluntary emissions recall reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Voluntary emissions recall reporting... Defect Reporting Requirements, Voluntary Emission Recall Program § 92.404 Voluntary emissions recall reporting. (a) When any manufacturer or remanufacturer initiates a voluntary emissions recall campaign...

76 FR 55655 - Notice of Submission for OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-08

... to the Office of Information and Regulatory Affairs, Attention: Education Desk Officer, Office of... Education Program (MEP) allocations based on reported defect rates. Copies of the information collection... DEPARTMENT OF EDUCATION Notice of Submission for OMB Review AGENCY: Department of Education...

40 CFR 85.1909 - Treatment of confidential information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Treatment of confidential information. 85.1909 Section 85.1909 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements...

40 CFR 85.1905 - Alternative report formats.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Alternative report formats. 85.1905 Section 85.1905 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1905...

Folic Acid Food Fortification—Its History, Effect, Concerns, and Future Directions

PubMed Central

Crider, Krista S.; Bailey, Lynn B.; Berry, Robert J.

2011-01-01

Periconceptional intake of folic acid is known to reduce a woman’s risk of having an infant affected by a neural tube birth defect (NTD). National programs to mandate fortification of food with folic acid have reduced the prevalence of NTDs worldwide. Uncertainty surrounding possible unintended consequences has led to concerns about higher folic acid intake and food fortification programs. This uncertainty emphasizes the need to continually monitor fortification programs for accurate measures of their effect and the ability to address concerns as they arise. This review highlights the history, effect, concerns, and future directions of folic acid food fortification programs. PMID:22254102

Loss of maintenance DNA methylation results in abnormal DNA origin firing during DNA replication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haruta, Mayumi; Shimada, Midori, E-mail: midorism@med.nagoya-cu.ac.jp; Nishiyama, Atsuya

The mammalian maintenance methyltransferase DNMT1 [DNA (cytosine-5-)-methyltransferase 1] mediates the inheritance of the DNA methylation pattern during replication. Previous studies have shown that depletion of DNMT1 causes a severe growth defect and apoptosis in differentiated cells. However, the detailed mechanisms behind this phenomenon remain poorly understood. Here we show that conditional ablation of Dnmt1 in murine embryonic fibroblasts (MEFs) resulted in an aberrant DNA replication program showing an accumulation of late-S phase replication and causing severely defective growth. Furthermore, we found that the catalytic activity and replication focus targeting sequence of DNMT1 are required for a proper DNA replication program.more » Taken together, our findings suggest that the maintenance of DNA methylation by DNMT1 plays a critical role in proper regulation of DNA replication in mammalian cells. - Highlights: • DNMT1 depletion results in an abnormal DNA replication program. • Aberrant DNA replication is independent of the DNA damage checkpoint in DNMT1cKO. • DNMT1 catalytic activity and RFT domain are required for proper DNA replication. • DNMT1 catalytic activity and RFT domain are required for cell proliferation.« less

First-principles study of defect formation in a photovoltaic semiconductor Cu2ZnGeSe4

NASA Astrophysics Data System (ADS)

Nishihara, Hironori; Maeda, Tsuyoshi; Wada, Takahiro

2018-02-01

The formation energies of neutral Cu, Zn, Ge, and Se vacancies in kesterite-type Cu2ZnGeSe4 were evaluated by first-principles pseudopotential calculations using plane-wave basis functions. The calculations were performed at typical points in Cu-(Zn1/2Ge1/2)-Se and Cu3Se2-ZnSe-GeSe2 pseudoternary phase diagrams for Cu2ZnGeSe4. The results were compared with those for Cu2ZnSnSe4, Cu2ZnGeS4, and Cu2ZnSnS4 calculated using the same version of the CASTEP program code. The results indicate that Cu vacancies are easily formed in Cu2ZnGeSe4 under the Cu-poor condition as in the above compounds and CuInSe2, suggesting that Cu2ZnGeSe4 is also a preferable p-type absorber material for thin-film solar cells. The formation energies of possible antisite defects, such as CuZn and CuGe, and of possible complex defects, such as CuZn+ZnCu, were also calculated and compared within the above materials. The antisite defect of CuZn, which has the smallest formation energy within the possible defects, is concluded to be the most hardly formed in Cu2ZnGeSe4 among the compounds.

The management of defective resin composite restorations: current trends in dental school teaching in Japan.

PubMed

Lynch, C D; Hayashi, M; Seow, L L; Blum, I R; Wilson, N H F

2013-01-01

The aim of this article is to investigate the contemporary teaching of the management of defective direct resin composite restorations in dental schools in Japan. A questionnaire relating to the teaching of the management of defective resin composite restorations was developed and e-mailed to 29 dental schools in Japan in 2010. Completed responses were received from 19 of the 29 invited schools (response rate = 66%). Eighteen schools (95%) report that they included the teaching of repair of direct defective resin composite restorations in their dental school programs. Thirteen schools reported that they included both clinical and didactic instruction on the repair of direct resin composite restorations. Fourteen schools did not teach any mechanical roughening of the exposed resin composite restoration surface before undertaking a repair. The most commonly reported treatment was acid etching with phosphoric acid (12 schools). The most commonly taught material for completing repairs was a flowable resin composite (16 schools). The teaching of repair of defective resin composite restorations is well established within many Japanese dental schools, to a greater extent than in some other regions of the world. The impact of this teaching on subsequent clinical practices in Japan should be investigated. Furthermore, it is concluded that there is a need for much stronger leadership in operative and conservative dentistry, ideally at the global level, to resolve differences in key aspects of operative procedures such as repairs.

Folic acid supplementation and the occurrence of congenital heart defects, orofacial clefts, multiple births, and miscarriage.

PubMed

Bailey, Lynn B; Berry, Robert J

2005-05-01

Key research findings relative to the question of whether maternal use of folic acid before and during pregnancy reduces the chance that offspring will be born with a congenital heart defect or an orofacial cleft are reviewed in this paper. Observational studies in general support an association between maternal use of multivitamins containing folic acid and a reduction in the occurrence of congenital heart defects and orofacial clefts. Results from one randomized controlled trial (RCT) provide the strongest evidence that multivitamins prevent congenital heart defects, but this RCT did not provide evidence that multivitamins prevent orofacial clefts. In addition, most observational and interventional studies are not designed to detect an independent effect from folic acid. Early studies suggested that periconceptional multivitamin use was associated with an increased occurrence of both miscarriages and multiple births, which has resulted in a great deal of controversy about the safety of folic acid use during pregnancy. We also review reports that were designed to answer these questions with more definitive data. When more substantial evidence about the effect of periconceptional folic acid on the occurrence of congenital heart defects and orofacial clefts is reported, we will have additional support for promoting folic acid intervention programs. All women capable of becoming pregnant should continue to consume 400 mug/d of folic acid in addition to a healthy diet as advised.

Strengthening of defected beam-column joints using CFRP.

PubMed

Mahmoud, Mohamed H; Afefy, Hamdy M; Kassem, Nesreen M; Fawzy, Tarek M

2014-01-01

This paper presents an experimental study for the structural performance of reinforced concrete (RC) exterior beam-column joints rehabilitated using carbon-fiber-reinforced polymer (CFRP). The present experimental program consists of testing 10 half-scale specimens divided into three groups covering three possible defects in addition to an adequately detailed control specimen. The considered defects include the absence of the transverse reinforcement within the joint core, insufficient bond length for the beam main reinforcement and inadequate spliced implanted column on the joint. Three different strengthening schemes were used to rehabilitate the defected beam-column joints including externally bonded CFRP strips and sheets in addition to near surface mounted (NSM) CFRP strips. The failure criteria including ultimate capacity, mode of failure, initial stiffness, ductility and the developed ultimate strain in the reinforcing steel and CFRP were considered and compared for each group for the control and the CFRP-strengthened specimens. The test results showed that the proposed CFRP strengthening configurations represented the best choice for strengthening the first two defects from the viewpoint of the studied failure criteria. On the other hand, the results of the third group showed that strengthening the joint using NSM strip technique enabled the specimen to outperform the structural performance of the control specimen while strengthening the joints using externally bonded CFRP strips and sheets failed to restore the strengthened joints capacity.

Effectiveness of the critical congenital heart disease screening program for early diagnosis of cardiac abnormalities in newborn infants.

PubMed

Almawazini, Abdulmajid M; Hanafi, Hamdi K; Madkhali, Hasan A; Majrashi, Noura B

2017-10-01

To evaluate the effectiveness of critical congenital heart disease (CCHD) screening program for early diagnosis of cardiac anomalies in newborn infants.  Methods: This is a hospital-based prospective cross-sectional study conducted in the Pediatric and Neonatology Department, King Fahad Hospital at  Albaha, Saudi Arabia, between February 2016 and February 2017. Results: We screened 2961 (95.4%) of 3103 patients in a nursery unit; 142 (4.6%) patients were not screened. The test was positive in 114 (3.9%) patients and negative in 2847 (96.1%). There were 94 (3.2%) false positives and 20 (0.7%) true positives. Critical cardiac defects were diagnosed in 7 (0.2%) patients of all screened infants, and severe pulmonary hypertension was diagnosed in 13 (0.4%) patients. True negative results were found in 2841(96%) patients, and no cardiac defect was diagnosed, whereas false negative results were seen in 6 (0.2%) patients diagnosed with ventricular septal defect. The sensitivity was 77%, and the specificity was very high at 97%, with a positive predictive value of 18%, and a negative predictive value of 99.8% (95% confidence interval 13.78-19.18, p=0.0001). Conclusion: Pulse oximetry was found to be easy, safe, sensitive, and highly specific for diagnosis of CCHD.

Simulation approach for optimization of ZnO/c-WSe{}_{2} heterojunction solar cells

NASA Astrophysics Data System (ADS)

Huang, Shihua; Li, Qiannan; Chi, Dan; Meng, Xiuqing; He, Lü

2017-04-01

Taking into account defect density in WSe{}2, interface recombination between ZnO and WSe{}2, we presented a simulation study of ZnO/crystalline WSe{}2 heterojunction (HJ) solar cell using wxAMPS simulation software. The optimal conversion efficiency 39.07% for n-ZnO/p-c-WSe{}2 HJ solar cell can be realized without considering the impact of defects. High defect density (> 1.0× {10}11 cm{}-2) in c-WSe{}2 and large trap cross-section (> 1.0 × 10{}-10 cm{}2) have serious impact on solar cell efficiency. A thin p-WSe{}2 layer is intentionally inserted between ZnO layer and c-WSe{}2 to investigate the effect of the interface recombination. The interface properties are very crucial to the performance of ZnO/c-WSe{}2HJ solar cell. The affinity of ZnO value range between 3.7-4.5 eV gives the best conversion efficiency. Project supported by the Natural Science Foundation of Zhejiang Province (No. LY17F040001), the Open Project Program of Surface Physics Laboratory (National Key Laboratory) of Fudan University (No. KF2015_02), the Open Project Program of National Laboratory for Infrared Physics, Chinese Academy of Sciences (No. M201503), the Zhejiang Provincial Science and Technology Key Innovation Team (No. 2011R50012), and the Zhejiang Provincial Key Laboratory (No. 2013E10022).

Fundamental Studies and Development of III-N Visible LEDs for High-Power Solid-State Lighting Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dupuis, Russell

The goal of this program is to understand in a fundamental way the impact of strain, defects, polarization, and Stokes loss in relation to unique device structures upon the internal quantum efficiency (IQE) and efficiency droop (ED) of III-nitride (III-N) light-emitting diodes (LEDs) and to employ this understanding in the design and growth of high-efficiency LEDs capable of highly-reliable, high-current, high-power operation. This knowledge will be the basis for our advanced device epitaxial designs that lead to improved device performance. The primary approach we will employ is to exploit new scientific and engineering knowledge generated through the application of amore » set of unique advanced growth and characterization tools to develop new concepts in strain-, polarization-, and carrier dynamics-engineered and low-defect materials and device designs having reduced dislocations and improved carrier collection followed by efficient photon generation. We studied the effects of crystalline defect, polarizations, hole transport, electron-spillover, electron blocking layer, underlying layer below the multiplequantum- well active region, and developed high-efficiency and efficiency-droop-mitigated blue LEDs with a new LED epitaxial structures. We believe new LEDs developed in this program will make a breakthrough in the development of high-efficiency high-power visible III-N LEDs from violet to green spectral region.« less

Friction pull plug welding: dual chamfered plate hole

NASA Technical Reports Server (NTRS)

Coletta, Edmond R. (Inventor); Cantrell, Mark A. (Inventor)

2001-01-01

Friction Pull Plug Welding (FPPW) is a solid state repair process for defects up to one inch in length, only requiring single sided tooling (OSL) for usage on flight hardware. Early attempts with FPPW followed the matching plug/plate geometry precedence of the successful Friction Push Plug Welding program, however no defect free welds were achieved due to substantial plug necking and plug rotational stalling. The dual chamfered hole has eliminated plug rotational stalling, both upon initial plug/plate contact and during welding. Also, the necking of the heated plug metal under a tensile heating/forging load has been eliminated through the usage of the dual chamfered plate hole.

The National Birth Defects Prevention Study: a review of the methods

PubMed Central

Reefhuis, Jennita; Gilboa, Suzanne M.; Anderka, Marlene; Browne, Marilyn L.; Feldkamp, Marcia L.; Hobbs, Charlotte A.; Jenkins, Mary M.; Langlois, Peter H.; Newsome, Kimberly B.; Olshan, Andrew F.; Romitti, Paul A.; Shapira, Stuart K.; Shaw, Gary M.; Tinker, Sarah C.; Honein, Margaret A.

2015-01-01

Background The National Birth Defects Prevention Study (NBDPS) is a large population-based multi-center case-control study of major birth defects in the United States. Methods Data collection took place from 1998 through 2013 on pregnancies ending between October 1997 and December 2011. Cases could be live born, stillborn or induced terminations, and were identified from birth defects surveillance programs in Arkansas, California, Georgia, Iowa, Massachusetts, New Jersey, New York, North Carolina, Texas and Utah. Controls were live born infants without major birth defects identified from the same geographical regions and time periods as cases via either vital records or birth hospitals. Computer-assisted telephone interviews were completed with women between 6 weeks and 24 months after the estimated date of delivery. After completion of interviews, families received buccal cell collection kits for the mother, father and infant (if living). Results There were 47,832 eligible cases and 18,272 eligible controls. Among these, 32,187 (67%) and 11,814 (65%) respectively, provided interview information about their pregnancies. Buccal cell collection kits with a cytobrush for at least one family member were returned by 19,065 case and 6,211 control families (65% and 59% of those who were sent a kit). More than 500 projects have been proposed by the collaborators and over 200 manuscripts published using data from the NBDPS through December 2014. Conclusion The NBDPS has made substantial contributions to the field of birth defects epidemiology through its rigorous design, including case classification, detailed questionnaire and specimen collection, large study population, and collaborative activities across Centers. PMID:26033852

The National Birth Defects Prevention Study: A review of the methods.

PubMed

Reefhuis, Jennita; Gilboa, Suzanne M; Anderka, Marlene; Browne, Marilyn L; Feldkamp, Marcia L; Hobbs, Charlotte A; Jenkins, Mary M; Langlois, Peter H; Newsome, Kimberly B; Olshan, Andrew F; Romitti, Paul A; Shapira, Stuart K; Shaw, Gary M; Tinker, Sarah C; Honein, Margaret A

2015-08-01

The National Birth Defects Prevention Study (NBDPS) is a large population-based multicenter case-control study of major birth defects in the United States. Data collection took place from 1998 through 2013 on pregnancies ending between October 1997 and December 2011. Cases could be live born, stillborn, or induced terminations, and were identified from birth defects surveillance programs in Arkansas, California, Georgia, Iowa, Massachusetts, New Jersey, New York, North Carolina, Texas, and Utah. Controls were live born infants without major birth defects identified from the same geographical regions and time periods as cases by means of either vital records or birth hospitals. Computer-assisted telephone interviews were completed with women between 6 weeks and 24 months after the estimated date of delivery. After completion of interviews, families received buccal cell collection kits for the mother, father, and infant (if living). There were 47,832 eligible cases and 18,272 eligible controls. Among these, 32,187 (67%) and 11,814 (65%), respectively, provided interview information about their pregnancies. Buccal cell collection kits with a cytobrush for at least one family member were returned by 19,065 case and 6,211 control families (65% and 59% of those who were sent a kit). More than 500 projects have been proposed by the collaborators and over 200 manuscripts published using data from the NBDPS through December 2014. The NBDPS has made substantial contributions to the field of birth defects epidemiology through its rigorous design, including case classification, detailed questionnaire and specimen collection, large study population, and collaborative activities across Centers. © 2015 Wiley Periodicals, Inc.

Periodontal repair in dogs: examiner reproducibility in the supraalveolar periodontal defect model.

PubMed

Koo, Ki-Tae; Polimeni, Giuseppe; Albandar, Jasim M; Wikesjö, Ulf M E

2004-06-01

Histometric assessments are routinely used to evaluate biologic events ascertained in histologic sections acquired from animal and human studies. The objective of this study was to evaluate the intra- and inter-examiner reproducibility of histometric assessments in the supraalveolar periodontal defect model. Histometric analysis using incandescent and polarized light microscopy, an attached digital camera system, and a PC-based image analysis system including a custom program for the supraalveolar periodontal defect model was performed on histologic sections acquired from one jaw quadrant in each of 12 dogs. The animals had received an experimental protocol including implantation of a coral biomaterial and guided tissue regeneration (GTR) barrier devices, and were evaluated following a 4-week healing interval. Histometric parameters were recorded and repeated within a 3-month interval by two examiners following brief training. Intra- and inter-examiner reproducibility was assessed using the intra-class correlation coefficient (ICC). Most parameters showed high intra-examiner ICCs. Parameters including defect height, connective tissue repair, bone regeneration (height/area), formation of a junctional epithelium, positioning of the GTR device, ankylosis, root resorption, and defect area yielded an ICC> or 0..9. The ICCs for bone density and biomaterial density were somewhat lower (0.8 and 0.7, respectively). The inter-examiner reproducibility was somewhat lower compared to the intra-examiner reproducibility. Nevertheless, the ICCs were generally high (ICC range: 0.6-0.9). Histometric evaluations in the supraalveolar periodontal defect model yield highly reproducible results, in particular when a single examiner performs the histometric measurements, even when the examiner was exposed to limited training.

Hemianopic and Quadrantanopic Field Loss, Eye and Head Movements, and Driving

PubMed Central

McGwin, Gerald; Elgin, Jennifer; Vaphiades, Michael S.; Braswell, Ronald A.; DeCarlo, Dawn K.; Kline, Lanning B.; Owsley, Cynthia

2011-01-01

Purpose. To compare eye and head movements, lane keeping, and vehicle control of drivers with hemianopic and quadrantanopic field defects with controls, and to identify differences in these parameters between hemianopic and quadrantanopic drivers rated safe to drive by a clinical driving rehabilitation specialist compared with those rated as unsafe. Methods. Eye and head movements and lane keeping were rated in 22 persons with homonymous hemianopic defects and 8 with quadrantanopic defects (mean age, 53 years) who were ≥6 months post-injury and 30 persons with normal fields (mean age, 53 years). All were licensed to drive and were current drivers or aimed to resume driving. Participants drove a 6.3-mile route along non-interstate city roads under in-traffic conditions. Vehicle control was assessed objectively by vehicle instrumentation for speed, braking, acceleration, and cornering. Results. As a group, drivers with hemianopic or quadrantanopic defects drove slower, exhibited less excessive cornering or acceleration, and executed more shoulder movements than the controls. Those drivers with hemianopic or quadrantanopic defects rated as safe also made more head movements into their blind field, received superior ratings regarding eye movement extent and lane position stability, and exhibited less sudden braking and drove faster than those rated unsafe. Conclusions. Persons with hemianopic and quadrantanopic defects rated as safe to drive compensated by making more head movements into their blind field, combined with more stable lane keeping and less sudden braking. Future research should evaluate whether these characteristics could be trained in rehabilitation programs aimed at improving driving safety in this population. PMID:21367969

Patterned mask inspection technology with Projection Electron Microscope (PEM) technique for 11 nm half-pitch (hp) generation EUV masks

NASA Astrophysics Data System (ADS)

Hirano, Ryoichi; Iida, Susumu; Amano, Tsuyoshi; Watanabe, Hidehiro; Hatakeyama, Masahiro; Murakami, Takeshi; Yoshikawa, Shoji; Suematsu, Kenichi; Terao, Kenji

2015-07-01

High-sensitivity EUV mask pattern defect detection is one of the major issues in order to realize the device fabrication by using the EUV lithography. We have already designed a novel Projection Electron Microscope (PEM) optics that has been integrated into a new inspection system named EBEYE-V30 ("Model EBEYE" is an EBARA's model code), and which seems to be quite promising for 16 nm hp generation EUVL Patterned mask Inspection (PI). Defect inspection sensitivity was evaluated by capturing an electron image generated at the mask by focusing onto an image sensor. The progress of the novel PEM optics performance is not only about making an image sensor with higher resolution but also about doing a better image processing to enhance the defect signal. In this paper, we describe the experimental results of EUV patterned mask inspection using the above-mentioned system. The performance of the system is measured in terms of defect detectability for 11 nm hp generation EUV mask. To improve the inspection throughput for 11 nm hp generation defect detection, it would require a data processing rate of greater than 1.5 Giga- Pixel-Per-Second (GPPS) that would realize less than eight hours of inspection time including the step-and-scan motion associated with the process. The aims of the development program are to attain a higher throughput, and enhance the defect detection sensitivity by using an adequate pixel size with sophisticated image processing resulting in a higher processing rate.

Dendrites are dispensable for basic motoneuron function but essential for fine tuning of behavior.

PubMed

Ryglewski, Stefanie; Kadas, Dimitrios; Hutchinson, Katie; Schuetzler, Natalie; Vonhoff, Fernando; Duch, Carsten

2014-12-16

Dendrites are highly complex 3D structures that define neuronal morphology and connectivity and are the predominant sites for synaptic input. Defects in dendritic structure are highly consistent correlates of brain diseases. However, the precise consequences of dendritic structure defects for neuronal function and behavioral performance remain unknown. Here we probe dendritic function by using genetic tools to selectively abolish dendrites in identified Drosophila wing motoneurons without affecting other neuronal properties. We find that these motoneuron dendrites are unexpectedly dispensable for synaptic targeting, qualitatively normal neuronal activity patterns during behavior, and basic behavioral performance. However, significant performance deficits in sophisticated motor behaviors, such as flight altitude control and switching between discrete courtship song elements, scale with the degree of dendritic defect. To our knowledge, our observations provide the first direct evidence that complex dendrite architecture is critically required for fine-tuning and adaptability within robust, evolutionarily constrained behavioral programs that are vital for mating success and survival. We speculate that the observed scaling of performance deficits with the degree of structural defect is consistent with gradual increases in intellectual disability during continuously advancing structural deficiencies in progressive neurological disorders.

38 CFR 21.8370 - Authorization of transportation services.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Birth Defects Transportation Services § 21.8370 Authorization of transportation services. (a) General... VA and non-VA programs; or (3) Can commute to school with family, friends, or fellow students... Budget has approved the information collection requirements in this section under control number 2900...

38 CFR 21.8370 - Authorization of transportation services.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Birth Defects Transportation Services § 21.8370 Authorization of transportation services. (a) General... VA and non-VA programs; or (3) Can commute to school with family, friends, or fellow students... Budget has approved the information collection requirements in this section under control number 2900...

38 CFR 21.8370 - Authorization of transportation services.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Birth Defects Transportation Services § 21.8370 Authorization of transportation services. (a) General... VA and non-VA programs; or (3) Can commute to school with family, friends, or fellow students... Budget has approved the information collection requirements in this section under control number 2900...

38 CFR 21.8370 - Authorization of transportation services.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Birth Defects Transportation Services § 21.8370 Authorization of transportation services. (a) General... VA and non-VA programs; or (3) Can commute to school with family, friends, or fellow students... Budget has approved the information collection requirements in this section under control number 2900...

14 CFR 91.1025 - Program operating manual contents.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional Ownership... flight; (f) Procedures to be followed by the pilot in command for determining that mechanical irregularities or defects reported for previous flights have been corrected or that correction of certain...

14 CFR 91.1025 - Program operating manual contents.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional Ownership... flight; (f) Procedures to be followed by the pilot in command for determining that mechanical irregularities or defects reported for previous flights have been corrected or that correction of certain...

14 CFR 91.1025 - Program operating manual contents.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional Ownership... flight; (f) Procedures to be followed by the pilot in command for determining that mechanical irregularities or defects reported for previous flights have been corrected or that correction of certain...

14 CFR 91.1025 - Program operating manual contents.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional Ownership... flight; (f) Procedures to be followed by the pilot in command for determining that mechanical irregularities or defects reported for previous flights have been corrected or that correction of certain...

14 CFR 91.1025 - Program operating manual contents.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional Ownership... flight; (f) Procedures to be followed by the pilot in command for determining that mechanical irregularities or defects reported for previous flights have been corrected or that correction of certain...

40 CFR 85.1906 - Report filing: Record retention.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Report filing: Record retention. 85.1906 Section 85.1906 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1906...

40 CFR 85.1907 - Responsibility under other legal provisions preserved.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Responsibility under other legal provisions preserved. 85.1907 Section 85.1907 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting...

40 CFR 85.1908 - Disclaimer of production warranty applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Disclaimer of production warranty applicability. 85.1908 Section 85.1908 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements...

40 CFR 85.1902 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1902 Definitions. Link to an...: (a) Act shall mean the Clean Air Act, 42 U.S.C. 1857, as amended. (b) The phrase emission-related...

Control of Suspect/Counterfeit and Defective Items

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheriff, Marnelle L.

2013-09-03

This procedure implements portions of the requirements of MSC-MP-599, Quality Assurance Program Description. It establishes the Mission Support Alliance (MSA) practices for minimizing the introduction of and identifying, documenting, dispositioning, reporting, controlling, and disposing of suspect/counterfeit and defective items (S/CIs). employees whose work scope relates to Safety Systems (i.e., Safety Class [SC] or Safety Significant [SS] items), non-safety systems and other applications (i.e., General Service [GS]) where engineering has determined that their use could result in a potential safety hazard. MSA implements an effective Quality Assurance (QA) Program providing a comprehensive network of controls and verification providing defense-in-depth by preventingmore » the introduction of S/CIs through the design, procurement, construction, operation, maintenance, and modification of processes. This procedure focuses on those safety systems, and other systems, including critical load paths of lifting equipment, where the introduction of S/CIs would have the greatest potential for creating unsafe conditions.« less

Activities of the Solid State Physics Research Institute

NASA Technical Reports Server (NTRS)

1984-01-01

Three research programs are reviewed. These programs are muon spin rotation, studies of annealing in gallium arsenide and Hall effect studies in semiconductors. The muon spin rotation work centers around the development of a facility at the Alternating Gradient Synchrotron of BNL. Studies of annealing in GaAs concerns itself with the measurement of depolarization in GaAs. The Hall effect studies of proton damaged semiconductors provide new information on the nature of defects and dislocations in GaAs.

Software Development Projects: Estimation of Cost and Effort (A Manager’s Digest).

DTIC Science & Technology

1982-12-01

it later when changes need to be made to it. Various levels of difficulty are experiencel .4 due to the skill level of the programmer, poor Orcaram...impurities that if eliminatel 4 reduce the level of complexity of the program. They are as follows: 16 1. Complementary Operations: unreduced expressions 2...greater quality than that to support standard business applications. Remus defines quality as "...the number of program defects normalized by size over

Hydrogen-bond Specific Materials Modification in Group IV Semiconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolk, Norman H.; Feldman, L. C.; Luepke, G.

Executive summary Semiconductor dielectric crystals consist of two fundamental components: lattice atoms and electrons. The former component provides a crystalline structure that can be disrupted by various defects or the presence of an interface, or by transient oscillations known as phonons. The latter component produces an energetic structure that is responsible for the optical and electronic properties of the material, and can be perturbed by lattice defects or by photo-excitation. Over the period of this project, August 15, 1999 to March 31, 2015, a persistent theme has been the elucidation of the fundamental role of defects arising from the presencemore » of radiation damage, impurities (in particular, hydrogen), localized strain or some combination of all three. As our research effort developed and evolved, we have experienced a few title changes, which reflected this evolution. Throughout the project, ultrafast lasers usually in a pump-probe configuration provided the ideal means to perturb and study semiconductor crystals by both forms of excitation, vibrational (phonon) and electronic (photon). Moreover, we have found in the course of this research that there are many interesting and relevant scientific questions that may be explored when phonon and photon excitations are controlled separately. Our early goals were to explore the dynamics of bond-selective vibrational excitation of hydrogen from point defects and impurities in crystalline and amorphous solids, initiating an investigation into the behavior of hydrogen isotopes utilizing a variety of ultrafast characterization techniques, principally transient bleaching spectroscopy to experimentally obtain vibrational lifetimes. The initiative could be divided into three related areas: (a) investigation of the change in electronic structure of solids due to the presence of hydrogen defect centers, (b) dynamical studies of hydrogen in materials and (c) characterization and stability of metastable hydrogen impurity states under transient compression. This research focused on the characterization of photon and ion stimulated hydrogen related defect and impurity reactions and migration in solid state matter, which requires a detailed understanding of the rates and pathways of vibrational energy flow, of the transfer channels and of the coupling mechanisms between local vibrational modes (LVMs) and phonon bath as well as the electronic system of the host material. It should be stressed that researchers at Vanderbilt and William and Mary represented a unique group with a research focus and capabilities for low temperature creation and investigation of such material systems. Later in the program, we carried out a vigorous research effort addressing the roles of defects, interfaces, and dopants on the optical and electronic characteristics of semiconductor crystals, using phonon generation by means of ultrafast coherent acoustic phonon (CAP) spectroscopy, nonlinear characterization using second harmonic generation (SHG), and ultrafast pump-and-probe reflectivity and absorption measurements. This program featured research efforts from hydrogen defects in silicon alone to other forms of defects such as interfaces and dopant layers, as well as other important semiconducting systems. Even so, the emphasis remains on phenomena and processes far from equilibrium, such as hot electron effects and travelling localized phonon waves. This program relates directly to the mission of the Department of Energy. Knowledge of the rates and pathways of vibrational energy flow in condensed matter is critical for understanding dynamical processes in solids including electronically, optically and thermally stimulated defect and impurity reactions and migration. The ability to directly probe these pathways and rates allows tests of theory and scaling laws at new levels of precision. Hydrogen embedded in model crystalline semiconductors and metal oxides is of particular interest, since the associated local mode can be excited cleanly, and is usually well-separated in energy from the phonon bath. These basic dynamical studies have provided new insights for example into the fundamental mechanisms that control proton diffusion in these oxides. This area of materials science has largely fulfilled its promise to identify degradation mechanisms in electronic and optoelectronic devices, and to advance solid oxide proton conductors for fuel cells, gas sensors and proton-exchange membrane applications. It also provides the basis for innovations in materials synthesis involving atomic-selective diffusion and desorption.« less

40 CFR 90.808 - Ordered recall provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-Related Defect Reporting Requirements, Voluntary Emission Recall Program, Ordered Recalls § 90.808 Ordered... manufacturer shall comply in all respects with the requirements of this subpart. (2) Any notification required... regulations at § 90.804. Such manufacturer is subject to the reporting and recordkeeping requirements of § 90...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2012 CFR

2012-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR § 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2013 CFR

2013-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2014 CFR

2014-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2010 CFR

2010-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2011 CFR

2011-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

Quantitative software models for the estimation of cost, size, and defects

NASA Technical Reports Server (NTRS)

Hihn, J.; Bright, L.; Decker, B.; Lum, K.; Mikulski, C.; Powell, J.

2002-01-01

The presentation will provide a brief overview of the SQI measurement program as well as describe each of these models and how they are currently being used in supporting JPL project, task and software managers to estimate and plan future software systems and subsystems.

38 CFR 21.8014 - Application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Vietnam Veterans-Spina Bifida and Covered Birth Defects General § 21.8014 Application. (a) Filing an application. To participate in a vocational training program, the child of a Vietnam veteran (or the child's... Vietnam veteran's full name and Social Security number or VA claim number, if any; and (3) Clearly...

38 CFR 21.8370 - Authorization of transportation services.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Certain Children of Vietnam Veterans-Spina Bifida and Covered Birth Defects Transportation Services § 21... non-VA programs; or (3) Can commute to school with family, friends, or fellow students. (Authority: 38... has approved the information collection requirements in this section under control number 2900-0580...

Field Demonstration of Electro-Scan Defect Location Technology for Condition Assessment of Wastewater Collection Systems

EPA Science Inventory

The purpose of the field demonstration program is to gather technically reliable cost and performance information on selected condition assessment technologies under defined field conditions. The selected technologies include zoom camera, electro-scan (FELL-41), and a multi-sens...

Report of Apollo 204 Review Board

NASA Technical Reports Server (NTRS)

1967-01-01

The Nation's space program requires that man and machine achieve the highest capability to pursue the exploration of space. The Apollo 204 Review Board was charged with the responsibility of reviewing the circumstances surrounding the accident, reporting its findings relating to the cause of the accident, and formulating recommendations so that inherent hazards are reduced to a minimum. The Board is very concerned that its description of the defects in the Apollo Program that led to the condition existing at the time of the Apollo 204 accident will be interpreted as an indictment of the entire manned space flight program and a castigation of the many people associated with that program. This report, rather than presenting a total picture of that program, is concerned with the deficiencies uncovered.

Orbital Wall Reconstruction with Two-Piece Puzzle 3D Printed Implants: Technical Note

PubMed Central

Mommaerts, Maurice Y.; Büttner, Michael; Vercruysse, Herman; Wauters, Lauri; Beerens, Maikel

2015-01-01

The purpose of this article is to describe a technique for secondary reconstruction of traumatic orbital wall defects using titanium implants that act as three-dimensional (3D) puzzle pieces. We present three cases of large defect reconstruction using implants produced by Xilloc Medical B.V. (Maastricht, the Netherlands) with a 3D printer manufactured by LayerWise (3D Systems; Heverlee, Belgium), and designed using the biomedical engineering software programs ProPlan and 3-Matic (Materialise, Heverlee, Belgium). The smaller size of the implants allowed sequential implantation for the reconstruction of extensive two-wall defects via a limited transconjunctival incision. The precise fit of the implants with regard to the surrounding ledges and each other was confirmed by intraoperative 3D imaging (Mobile C-arm Systems B.V. Pulsera, Philips Medical Systems, Eindhoven, the Netherlands). The patients showed near-complete restoration of orbital volume and ocular motility. However, challenges remain, including traumatic fat atrophy and fibrosis. PMID:26889349

Instabilities and patterns in an active nematic film

NASA Astrophysics Data System (ADS)

Srivastava, Pragya; Marchetti, Cristina

2015-03-01

Experiments on microtubule bundles confined to an oil-water interface have motivated extensive theoretical studies of two-dimensional active nematics. Theoretical models taking into account the interplay between activity, flow and order have remarkably reproduced several experimentally observed features of the defect-dynamics in these ``living'' nematics. Here, we derive minimal description of a two-dimensional active nematic film confined between walls. At high friction, we eliminate the flow to obtain closed equations for the nematic order parameter, with renormalized Frank elastic constants. Active processes can render the ``Frank'' constants negative, resulting in the instability of the uniformly ordered nematic state. The minimal model yields emergent patterns of growing complexity with increasing activity, including bands and turbulent dynamics with a steady density of topological defects, as obtained with the full hydrodynamic equations. We report on the scaling of the length scales of these patterns and of the steady state number of defects with activity and system size. National Science Foundation grant DMR-1305184 and Syracuse Soft Matter Program.

Visualization and quantification of deformation processes controlling the mechanical response of alloys in aggressive environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, Ian M.

The overall objective of this program was to develop the technique of electron tomography for studies of defects and to couple it with real time dynamic experiments such that four-dimensional (time and three spatial dimensions) characterization of dislocation interactions with defects is feasible and apply it to discovery of the fundamental unit processes of dislocation-defect interactions in metallic systems. Strategies to overcome the restrictions normally associated with electron tomography and to make it practical within the constraints of conducting a dynamic experiment in the transmission electron microscope were developed. These methods were used to determine the mechanism controlling the transfermore » of slip across grain boundaries in FCC and HCP metals, dislocation precipitate interactions in Al alloys, and dislocation-dislocation interactions in HCP Ti. In addition, preliminary investigations of slip transfer across cube-on-cube and incoherent twin interfaces in a multi-layered system, thermal stability of grains in nanongrained Ni and Fe, and on corrosion of Fe films were conducted.« less

Understanding Tort Liability and Its Relationship to Extension Professionals.

ERIC Educational Resources Information Center

Long, Norman D.; And Others

This study focuses on tort liability and its relationship to extension professionals working with 4-H programs. Tort liability as related to extension professionals consists of ten components: due care, physical defects (inspection of premises), instruction and supervision, first aid and medical treatment, foreseeability, causation, defamation,…

Field Demonstration of Electro-Scan Defect Location Technology for Condition Assessment of Wastewater Collection Systems - Paper

EPA Science Inventory

A USEPA-sponsored field demonstration program was conducted to gather technically reliable cost and performance information on the electro-scan (FELL -41) pipeline condition assessment technology. Electro-scan technology can be used to estimate the magnitude and location of pote...

School Security and Safety.

ERIC Educational Resources Information Center

Licht, Kenneth F.

The author contends that safety and accident prevention should be given primary consideration in a school system's risk management program. He argues that accidents and losses are symptoms of defects in the management system. Two classes of loss discussed are (1) accidental -- injury/loss resulting from unintended events; and (2) purposeful --…

Neurocognitive Defects and Their Impact on Substance Abuse Treatment.

ERIC Educational Resources Information Center

Fals-Stewart, William

1993-01-01

Examined prevalence of cognitive deficits in substance abusers (n=108) referred by criminal justice system to complete treatment in drug-free therapeutic community. Findings revealed that substance abusers with neuropsychological deficits were more likely to be removed from program for failure to follow rules and ultimately stayed in residence…

Cross-Cultural Training in the Community College Curriculum.

ERIC Educational Resources Information Center

Coller, Richard W.; Summers, John Mark

While technological advances have transformed man's social and cultural environment and increased the interconnection between individuals and cultures, they have not in themselves led to a deeper understanding of other cultures. Educational programs can play an important role in remedying this defect and in developing students' sensitivity to…

Imrovement of the cold forming technology of the parts such as longeron

NASA Astrophysics Data System (ADS)

Kashapova, L. R.; Pankratov, D. L.; Bilyalova, A. A.

2014-12-01

As a result of modeling in LS-PREPOST preprocessor of the program LS-DYNA a range of radii of curvature edge transition matrix (27,5 ° <= R <= 48 °) is obtained, which allows to produce defect-free stamping slots for longeron shock absorbers of tractors KAMAZ-5460.

Application of superalloy powder metallurgy for aircraft engines

NASA Technical Reports Server (NTRS)

Dreshfield, R. L.; Miner, R. V., Jr.

1980-01-01

The results of the Materials for Advanced Turbine Engines (MATE) program initiated by NASA are presented. Mechanical properties comparisons are made for superalloy parts produced by as-HIP powder consolidation and by forging of HIP consolidated billets. The effect of various defects on the mechanical properties of powder parts are shown.

Computational Simulation of Containment Influence on Defect Generation During Growth of GeSi

NASA Technical Reports Server (NTRS)

Motakef, Shariar; Yesilyurt, S.; Vujisic, L.

2001-01-01

This report contains results of theoretical work in conjunction with the NASA RDGS program. It is specifically focused on factors controlling the stability of detachment and the sensitivity of the detachment process to the processing and geometric parameters of the crystal growth process.

Positron Annihilation Gamma Ray Lineshape Studies of Defects in Solids.

DTIC Science & Technology

1980-06-24

of R. Waki in the development of anneal probably polygonized the zinc more completely the computer programs and for other experimental than did the...positron lifetime measurements. The assistance of R. Waki was greatly appreciated. References /1/ B.D. BOGGS and J.G. BYRNE, Metallurg.Trans. 4, 2153

29 CFR 1953.6 - Review and approval of plan supplements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 1953.6 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION...) OSHA shall review a supplement to determine whether it is at least as effective as the Federal program.... If the review reveals any defect in the supplement, or if more information is needed, OSHA shall...

29 CFR 1953.6 - Review and approval of plan supplements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 1953.6 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION...) OSHA shall review a supplement to determine whether it is at least as effective as the Federal program.... If the review reveals any defect in the supplement, or if more information is needed, OSHA shall...

Understanding Risk Management in the DoD

DTIC Science & Technology

2003-01-01

contract law that government specifications in a con- tract are accurate. Therefore, if a specifi- cation proves to be defective, a contactor is...accurate. THE ROLE OF THE CONTRACTING OFFICER Given the subtleties of the contract law that could impact the success of a Project’s risk management program

7 CFR 1924.266 - Purposes for which claims may be approved.

Code of Federal Regulations, 2010 CFR

2010-01-01

... OF AGRICULTURE PROGRAM REGULATIONS CONSTRUCTION AND REPAIR Complaints and Compensation for Construction Defects § 1924.266 Purposes for which claims may be approved. (a) Eligible purposes. A claim may... 7 Agriculture 12 2010-01-01 2010-01-01 false Purposes for which claims may be approved. 1924.266...

40 CFR 85.1904 - Voluntary emissions recall report; quarterly reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 19 2012-07-01 2012-07-01 false Voluntary emissions recall report; quarterly reports. 85.1904 Section 85.1904 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1904 Voluntary emissions...

40 CFR 85.1904 - Voluntary emissions recall report; quarterly reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 19 2014-07-01 2014-07-01 false Voluntary emissions recall report; quarterly reports. 85.1904 Section 85.1904 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1904 Voluntary emissions...

40 CFR 85.1904 - Voluntary emissions recall report; quarterly reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 18 2011-07-01 2011-07-01 false Voluntary emissions recall report; quarterly reports. 85.1904 Section 85.1904 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1904 Voluntary emissions...

40 CFR 85.1904 - Voluntary emissions recall report; quarterly reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 19 2013-07-01 2013-07-01 false Voluntary emissions recall report; quarterly reports. 85.1904 Section 85.1904 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Emission Defect Reporting Requirements § 85.1904 Voluntary emissions...

Defect Reduction in GaAs/Si Films with the a-Si Buffer Layer Grown by Metalorganic Chemical Vapor Deposition

NASA Astrophysics Data System (ADS)

Wang, Jun; Hu, Hai-Yang; He, Yun-Rui; Deng, Can; Wang, Qi; Duan, Xiao-Feng; Huang, Yong-Qing; Ren, Xiao-Min

2015-08-01

Not Available Supported by the Fund of State Key Laboratory of Information Photonics and Optical Communications of Beijing University of Posts and Telecommunications, the National Basic Research Program of China under Grant No 2010CB327601, the Natural Science Foundational Science and Technology Cooperation Projects under Grant No 2011RR000100, the 111 Project of China under Grant No B07005, and the Doctoral Program of Higher Specialized Research Fund under Grant No 20130005130001.

Antihistamine Use in Early Pregnancy and Risk of Birth Defects

PubMed Central

Li, Qian; Mitchell, Allen A.; Werler, Martha M.; Yau, Wai-Ping; Hernández-Díaz, Sonia

2014-01-01

Background Several studies have reported an association between use of specific antihistamines in early pregnancy and certain specific birth defects. Objective To test 16 previously-hypothesized associations between specific antihistamines and specific birth defects, and identify possible new associations. Methods We used 1998-2010 data from the Slone Epidemiology Center Birth Defects Study, a multicenter case-control surveillance program of birth defects in North America. Mothers were interviewed within six months of delivery about demographic, reproductive, medical, and behavioral factors, and details on use of prescription and non-prescription medications. We compared 1st trimester exposure to specific antihistamines between 13,213 infants with specific malformations and 6,982 non-malformed controls, using conditional logistic regression to estimate odds ratios (ORs) and 95% confidence intervals (CIs), with adjustment for potential confounders, including indication for use. Results Overall, 13.7% of controls were exposed to antihistamines during the 1st trimester. The most commonly-used medications were diphenhydramine (4.2%), loratadine (3.1%), doxylamine (1.9%), and chlorpheniramine (1.7%). Where estimates were stable, none supported the previously-hypothesized associations. Among over 100 exploratory comparisons of other specific antihistamine/defect pairs, 14 had ORs ≥1.5 of which 6 had 95% CI bounds excluding 1.0 before but not after adjustment for multiple comparisons. Conclusion Our findings do not provide meaningful support for previously-posited associations between antihistamines and major congenital anomalies; at the same time, we identified associations that had not been previously suggested. We suspect that previous associations may be chance findings in the context of multiple comparisons, a situation which may also apply to our new findings. PMID:24565715

Emerging topics in cutaneous wound repair.

PubMed

Valacchi, Giuseppe; Zanardi, Iacopo; Sticozzi, Claudia; Bocci, Velio; Travagli, Valter

2012-07-01

The intervention strategies in various types of skin wounds include several treatment programs that depend on the identified disease. Several factors such as aging, defective nutrition, traumatism, atherosclerosis, and diabetes may contribute to the formation of a wound that has no tendency to heal due to a defective and complicated repair process. The numerous advances in the understanding of the wound-healing process in both acute and chronic lesions have been recently described. The purpose of this paper is to describe relatively new approaches as viable alternatives to current wound-healing therapies. The future challenges for both the best targeting and optimization of these potential treatments are also described. © 2012 New York Academy of Sciences.

Meeting the challenge: using policy to improve children's health.

PubMed

Brush, Charles Adam; Kelly, Maggie M; Green, Denise; Gaffney, Marcus; Kattwinkel, John; French, Molly

2005-11-01

We reflect on the proceedings of a symposium at a conference of the Centers for Disease Control and Prevention National Center on Birth Defects and Developmental Disabilities. We present examples of bridging the gap between science and policy to achieve improvements in children's health through case studies in early hearing detection and intervention, folic acid fortification to prevent birth defects, sleep positioning recommendations to reduce infant mortality, and workplace lactation support programs. We discuss case studies that present different policy strategies (public health law and voluntary practices) for improving public health. These case studies demonstrate both the power of policy as a tool for improving children's health and the challenges of communicating public health research to policy decisionmakers.

Feasibility of a Team Approach to Complex Congenital Heart Defect Neurodevelopmental Follow-Up: Early Experience of a Combined Cardiology/Neonatal Intensive Care Unit Follow-Up Program.

PubMed

Chorna, Olena; Baldwin, H Scott; Neumaier, Jamie; Gogliotti, Shirley; Powers, Deborah; Mouvery, Amanda; Bichell, David; Maitre, Nathalie L

2016-07-01

Infants with complex congenital heart disease are at high risk for poor neurodevelopmental outcomes. However, implementation of dedicated congenital heart disease follow-up programs presents important infrastructure, personnel, and resource challenges. We present the development, implementation, and retrospective review of 1- and 2-year outcomes of a Complex Congenital Heart Defect Neurodevelopmental Follow-Up program. This program was a synergistic approach between the Pediatric Cardiology, Cardiothoracic Surgery, Pediatric Intensive Care, and Neonatal Intensive Care Unit Follow-Up teams to provide a feasible and responsible utilization of existing infrastructure and personnel, to develop and implement a program dedicated to children with congenital heart disease. Trained developmental testers administered the Ages and Stages Questionnaire-3 over the phone to the parents of all referred children at least once between 6 and 12 months' corrected age. At 18 months' corrected age, all children were scheduled in the Neonatal Intensive-Care Unit Follow-Up Clinic for a visit with standardized neurological exams, Bayley III, multidisciplinary therapy evaluations and continued follow-up. Of the 132 patients identified in the Cardiothoracic Surgery database and at discharge from the hospital, a total number of 106 infants were reviewed. A genetic syndrome was identified in 23.4% of the population. Neuroimaging abnormalities were identified in 21.7% of the cohort with 12.8% having visibly severe insults. As a result, 23 (26.7%) received first-time referrals for early intervention services, 16 (13.8%) received referrals for new services in addition to their existing ones. We concluded that utilization of existing resources in collaboration with established programs can ensure targeted neurodevelopmental follow-up for all children with complex congenital heart disease. © 2016 American Heart Association, Inc.

Developmental programming: postnatal estradiol amplifies ovarian follicular defects induced by fetal exposure to excess testosterone and dihydrotestosterone in sheep.

PubMed

Veiga-Lopez, A; Wurst, A K; Steckler, T L; Ye, W; Padmanabhan, V

2014-04-01

Excess of prenatal testosterone (T) induces reproductive defects including follicular persistence. Comparative studies with T and dihydrotestosterone (DHT) have suggested that follicular persistence is programmed via estrogenic actions of T. This study addresses the androgenic and estrogenic contributions in programming follicular persistence. Because humans are exposed to estrogenic environmental steroids from various sources throughout their life span and postnatal insults may also induce organizational and/or activational changes, we tested whether continuous postnatal exposure to estradiol (E) will amplify effects of prenatal steroids on ovarian function. Pregnant sheep were treated with T, DHT, E, or ED (E and DHT) from days 30 to 90 of gestation. Postnatally, a subset of the vehicle (C), T, and DHT females received an E implant. Transrectal ultrasonography was performed in the first breeding season during a synchronized cycle to monitor ovarian follicular dynamics. As expected, number of ≥8 mm follicles was higher in the T versus C group. Postnatal E reduced the number of 4 to 8 mm follicles in the DHT group. Percentage of females bearing luteinized follicles and the number of luteinized follicles differed among prenatal groups. Postnatal E increased the incidence of subluteal cycles in the prenatal T-treated females. Findings from this study confirm previous findings of divergences in programming effects of prenatal androgens and estrogens. They also indicate that some aspects of follicular dynamics are subject to postnatal modulation as well as support the existence of an extended organizational period or the need for a second insult to uncover the previously programmed event.

Adaptation of Lean Six Sigma Methodologies for the Evaluation of Veterans Choice Program at 3 Urban Veterans Affairs Medical Centers.

PubMed

Ball, Sherry L; Stevenson, Lauren D; Ladebue, Amy C; McCreight, Marina S; Lawrence, Emily C; Oestreich, Taryn; Lambert-Kerzner, Anne C

2017-07-01

The Veterans Health Administration (VHA) is adapting to meet the changing needs of our Veterans. VHA leaders are promoting quality improvement strategies including Lean Six Sigma (LSS). This study used LSS tools to evaluate the Veterans Choice Program (VCP), a program that aims to improve access to health care services for eligible Veterans by expanding health care options to non-VHA providers. LSS was utilized to assess the current process and efficiency patterns of the VCP at 3 VHA Medical Centers. LSS techniques were used to assess data obtained through semistructured interviews with Veterans, staff, and providers to describe and evaluate the VCP process by identifying wastes and defects. The LSS methodology facilitated the process of targeting priorities for improvement and constructing suggestions to close identified gaps and inefficiencies. Identified key process wastes included inefficient exchange of clinical information between stakeholders in and outside of the VHA; poor dissemination of VCP programmatic information; shortages of VCP-participating providers; duplication of appointments; declines in care coordination; and lack of program adaptability to local processes. Recommendations for improvement were formulated using LSS. This evaluation illustrates how LSS can be utilized to assess a nationally mandated health care program. By focusing on stakeholder, staff, and Veteran perspectives, process defects in the VCP were identified and improvement recommendations were made. However, the current LSS language used is not intuitive in health care and similar applications of LSS may consider using new language and goals adapted specifically for health care.

Biomechanical characteristics of hemi-hamate reconstruction versus volar plate arthroplasty in the treatment of dorsal fracture dislocations of the proximal interphalangeal joint.

PubMed

Tyser, Andrew R; Tsai, Michael A; Parks, Brent G; Means, Kenneth R

2015-02-01

To compare stability and range of motion after hemi-hamate reconstruction versus volar plate arthroplasty in a biomechanical proximal interphalangeal (PIP) joint fracture-dislocation model. Eighteen digits from 6 cadaver hands were tested. We created defects of 40%, 60%, and 80% in the palmar base of each digit's middle phalanx, simulating an acute PIP joint fracture-dislocation. Each defect scenario was reconstructed with a hemi-hamate arthroplasty followed by a volar plate arthroplasty. A computer-controlled mechanism was used to bring each digit's PIP joint from full extension to full flexion via the digital tendons in each testing state, and in the intact state. During each testing scenario we collected PIP joint cinedata in a true lateral projection using mini-fluoroscopy. A digital radiography program was used to measure the amount of middle phalanx dorsal translation (subluxation) in full PIP joint extension. We recorded the angle at which subluxation, if present, occurred during each testing scenario. Average dorsal displacement of the middle phalanx in relation to the proximal phalanx was 0.01 mm for the hemi-hamate reconstructed joints and -0.03 mm for the volar plate arthroplasty, compared with the intact state. Flexion contractures were noted in each of the specimens reconstructed with volar plate arthroplasty. Degree of contracture was directly correlated with defect size, averaging 20° for 40% defects, 35° for 60% defects, and 60° for 80% defects. We observed no flexion contractures in the hemi-hamate reconstructions. Surgeons can use both hemi-hamate and volar plate arthroplasty to restore PIP joint stability following a fracture dislocation with a large middle phalanx palmar base defect. Use of volar plate arthroplasty led to an increasing flexion contracture as the middle phalanx palmar base defect increased. Clinicians can use the information from this study to help with surgical decision-making and patient education. Copyright © 2015 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Mass extraction container closure integrity physical testing method development for parenteral container closure systems.

PubMed

Yoon, Seung-Yil; Sagi, Hemi; Goldhammer, Craig; Li, Lei

2012-01-01

Container closure integrity (CCI) is a critical factor to ensure that product sterility is maintained over its entire shelf life. Assuring the CCI during container closure (C/C) system qualification, routine manufacturing and stability is important. FDA guidance also encourages industry to develop a CCI physical testing method in lieu of sterility testing in a stability program. A mass extraction system has been developed to check CCI for a variety of container closure systems such as vials, syringes, and cartridges. Various types of defects (e.g., glass micropipette, laser drill, wire) were created and used to demonstrate a detection limit. Leakage, detected as mass flow in this study, changes as a function of defect length and diameter. Therefore, the morphology of defects has been examined in detail with fluid theories. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water, placebo, or drug product (3 mg/mL concentration) solution. Also, it has been verified that the method was robust, and capable of determining the acceptance limit using 3σ for syringes and 6σ for vials. Sterile products must maintain their sterility over their entire shelf life. Container closure systems such as those found in syringes and vials provide a seal between rubber and glass containers. This seal must be ensured to maintain product sterility. A mass extraction system has been developed to check container closure integrity for a variety of container closure systems such as vials, syringes, and cartridges. In order to demonstrate the method's capability, various types of defects (e.g., glass micropipette, laser drill, wire) were created in syringes and vials and were tested. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water, placebo, or drug product (3 mg/mL concentration) solution. Also, it was verified that the method showed consistent results, and was able to determine the acceptance limit using 3σ for syringes and 6σ for vials.

Surveillance metrics sensitivity study.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamada, Michael S.; Bierbaum, Rene Lynn; Robertson, Alix A.

2011-09-01

In September of 2009, a Tri-Lab team was formed to develop a set of metrics relating to the NNSA nuclear weapon surveillance program. The purpose of the metrics was to develop a more quantitative and/or qualitative metric(s) describing the results of realized or non-realized surveillance activities on our confidence in reporting reliability and assessing the stockpile. As a part of this effort, a statistical sub-team investigated various techniques and developed a complementary set of statistical metrics that could serve as a foundation for characterizing aspects of meeting the surveillance program objectives. The metrics are a combination of tolerance limit calculationsmore » and power calculations, intending to answer level-of-confidence type questions with respect to the ability to detect certain undesirable behaviors (catastrophic defects, margin insufficiency defects, and deviations from a model). Note that the metrics are not intended to gauge product performance but instead the adequacy of surveillance. This report gives a short description of four metrics types that were explored and the results of a sensitivity study conducted to investigate their behavior for various inputs. The results of the sensitivity study can be used to set the risk parameters that specify the level of stockpile problem that the surveillance program should be addressing.« less

Surveillance Metrics Sensitivity Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bierbaum, R; Hamada, M; Robertson, A

2011-11-01

In September of 2009, a Tri-Lab team was formed to develop a set of metrics relating to the NNSA nuclear weapon surveillance program. The purpose of the metrics was to develop a more quantitative and/or qualitative metric(s) describing the results of realized or non-realized surveillance activities on our confidence in reporting reliability and assessing the stockpile. As a part of this effort, a statistical sub-team investigated various techniques and developed a complementary set of statistical metrics that could serve as a foundation for characterizing aspects of meeting the surveillance program objectives. The metrics are a combination of tolerance limit calculationsmore » and power calculations, intending to answer level-of-confidence type questions with respect to the ability to detect certain undesirable behaviors (catastrophic defects, margin insufficiency defects, and deviations from a model). Note that the metrics are not intended to gauge product performance but instead the adequacy of surveillance. This report gives a short description of four metrics types that were explored and the results of a sensitivity study conducted to investigate their behavior for various inputs. The results of the sensitivity study can be used to set the risk parameters that specify the level of stockpile problem that the surveillance program should be addressing.« less

Investigation of 3C-SiC/SiO2 interfacial point defects from ab initio g-tensor calculations and electron paramagnetic resonance measurements

NASA Astrophysics Data System (ADS)

Nugraha, T. A.; Rohrmueller, M.; Gerstmann, U.; Greulich-Weber, S.; Stellhorn, A.; Cantin, J. L.; von Bardeleben, J.; Schmidt, W. G.; Wippermann, S.

SiC is widely used in high-power, high-frequency electronic devices. Recently, it has also been employed as a building block in nanocomposites used as light absorbers in solar energy conversion devices. Analogous to Si, SiC features SiO2 as native oxide that can be used for passivation and insulating layers. However, a significant number of defect states are reported to form at SiC/SiO2 interfaces, limiting mobility and increasing recombination of free charge carriers. We investigated the growth of oxide on different 3C-SiC surfaces from first principles. Carbon antisite Csi defects are found to be strongly stabilized in particular at the interface, because carbon changes its hybridization from sp3 in the SiC-bulk to sp2 at the interface, creating a dangling bond inside a porous region of the SiO2 passivating layer. Combining ab initio g-tensor calculations and electron paramagnetic resonance (EPR) measurements, we show that Csi defects explain the measured EPR signatures, while the hyperfine structure allows to obtain local structural information of the oxide layer. Financial support from BMBF NanoMatFutur Grant 13N12972 and DFG priority program SPP-1601 is gratefully acknowledged.

PHYSICAL THERAPY INTERVENTION FOR A FORMER POWER LIFTER AFTER ARTHROSCOPIC MICROFRACTURE PROCEDURE FOR GRADE IV GLENOHUMERAL CHONDRAL DEFECTS

PubMed Central

Sum, Jonathan

2011-01-01

Background: Power lifting places the shoulder complex at risk for injury. Microfracture is a relatively new procedure for chondral defects of the glenohumeral joint and is not well described in the literature. Objectives: The purpose of this case report is to describe the post-operative rehabilitation used with a power lifter who underwent a microfracture procedure to address glenoid and humeral chondral defects, debridement of type I superior labral anterior-posterior lesion, and a subacromial decompression. Case Description: The patient was a 46 year-old male who was evaluated nine weeks status-post arthroscopic microfracture procedure for glenoid and humeral chondral defects, debridement of superior labral anterior-posterior (SLAP) lesion, and subacromial decompression. Rehabilitation consisted of postural education, manual therapy, rotator cuff and scapular strengthening, dynamic stabilization, weightbearing exercises, and weight training over nine weeks (24 sessions). Lifting modifications were addressed. Outcomes: Results of the QuickDASH indicate that activities of daily living (ADLs), work, and sports modules all improved significantly, and the patient was able to return to recreational power lifting with limited discomfort or restrictions. Discussion: A structured post-operative physical therapy treatment program allowed this patient to return to recreational power lifting while restoring independent function for work-related activities and ADLs. PMID:21655454

Developmental programming: Impact of prenatal exposure to bisphenol-A and methoxychlor on steroid feedbacks in sheep

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abi Salloum, Bachir; Steckler, Teresa L.; Herkimer, Carol

Bisphenol-A (BPA), a polymer used in plastics manufacturing, and methoxychlor (MXC), a pesticide, are endocrine disrupting compounds with estrogenic and anti-androgenic properties. Prenatal BPA or MXC treatment induces reproductive defects in sheep with BPA causing prepubertal luteinizing hormone (LH) hypersecretion and dampening of periovulatory LH surges and MXC lengthening follicular phase and delaying the LH surge. In this study, we addressed the underlying neuroendocrine defects by testing the following hypotheses: 1) prenatal BPA, but not MXC reduces sensitivity to estradiol and progesterone negative feedback, 2) prenatal BPA, but not MXC increases pituitary responsiveness to gonadotropin releasing hormone (GnRH), and 3)more » prenatal BPA dampens LH surge response to estradiol positive feedback challenge while prenatal MXC delays the timing of the LH surge. Pregnant sheep were treated with either 1) 5 mg/kg/day BPA (produces approximately twice the level found in human circulation, n = 8), 2) 5 mg/kg/day MXC (the lowest observed effect level stated in the EPA National Toxicology Program's Report; n = 6), or 3) vehicle (cotton seed oil: C: n = 6) from days 30 to 90 of gestation. Female offspring of these ewes were ovariectomized at 21 months of age and tested for progesterone negative, estradiol negative, estradiol positive feedback sensitivities and pituitary responsiveness to GnRH. Results revealed that sensitivity to all 3 feedbacks as well as pituitary responsiveness to GnRH were not altered by either of the prenatal treatments. These findings suggest that the postpubertal reproductive defects seen in these animals may have stemmed from ovarian defects and the steroidal signals emanating from them. - Highlights: ► Prenatal BPA/MXC does not affect reproductive neuroendocrine steroid feedbacks. ► Prenatal BPA or MXC treatment failed to alter pituitary sensitivity to GnRH. ► LH excess in BPA-treated sheep may be due to reduced ovarian feedback signals.« less

TREEGRAD: a grading program for eastern hardwoods

Treesearch

J.W. Stringer; D.W. Cremeans

1991-01-01

Assigning tree grades to eastern hardwoods is often a difficult task for neophyte graders. Recently several "dichotomous keys" have been developed for training graders in the USFS hardwood tree grading system. TREEGRAD uses the Tree Grading Algorithm (TGA) for determining grades from defect location data and is designed to be used as a teaching aid.

HgCdTe Surface and Defect Study Program.

DTIC Science & Technology

1985-07-01

a! Td . - a,+ - , are the bonding and antibonding one electron energy states "- "𔃾 owing only to covalent and ionic interactions, . = T . . (U6 II .1...Group Meeting. Boulder CO. 1983; T. W. Jamet atid B. Fandvacncyforatin eerg) t inreae popotioal o a Ziack. 4bd . low inverse power of the average bond

Computer optimization of cutting yield from multiple ripped boards

Treesearch

A.R. Stern; K.A. McDonald

1978-01-01

RIPYLD is a computer program that optimizes the cutting yield from multiple-ripped boards. Decisions are based on automatically collected defect information, cutting bill requirements, and sawing variables. The yield of clear cuttings from a board is calculated for every possible permutation of specified rip widths and both the maximum and minimum percent yield...

40 CFR 1068.510 - How do I prepare and apply my remedial plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) AIR POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Reporting Defects and Recalling Engines/Equipment § 1068.510 How do I prepare and apply my remedial plan? (a) In your remedial plan, describe all of the following: (1) The class or category of engines/equipment to be recalled...

Proceedings of the 2016 National Toxicology Program Satellite Symposium

PubMed Central

Elmore, Susan A.; Chen, Vivian S.; Hayes-Bouknight, Schantel; Hoane, Jessica S.; Janardhan, Kyathanahalli; Kooistra, Linda H.; Nolte, Thomas; Szabo, Kathleen A.; Willson, Gabrielle A.; Wolf, Jeffrey C.; Malarkey, David E.

2016-01-01

The 2016 annual National Toxicology Program (NTP) Satellite Symposium, entitled “Pathology Potpourri” was held in San Diego, California, at the Society of Toxicologic Pathology’s (STP) 35th annual meeting. The goal of this symposium was to present and discuss challenging diagnostic pathology and/or nomenclature issues. This article presents summaries of the speakers’ talks, along with select images that were used by the audience for voting and discussion. Some lesions and topics covered during the symposium included malignant glioma and histiocytic sarcoma in the rodent brain; a new statistical method designed for histopathology data evaluation; uterine stromal/glandular polyp in a rat; malignant plasma cell tumor in a mouse brain; Schwann cell proliferative lesions in rat hearts; axillary schwannoma in a cat; necrosis and granulomatous inflammation in a rat brain; adenoma/carcinoma in a rat adrenal gland; hepatocyte maturation defect and liver/spleen hematopoietic defects in an embryonic mouse; distinguishing malignant glioma, malignant mixed glioma and malignant oligodendroglioma in the rat; comparison of mammary gland whole mounts and histopathology from mice; and discussion of the International Harmonization of Nomenclature and Diagnostic Criteria (INHAND) collaborations. PMID:27821709

Proceedings of the 2016 National Toxicology Program Satellite Symposium.

PubMed

Elmore, Susan A; Chen, Vivian S; Hayes-Bouknight, Schantel; Hoane, Jessica S; Janardhan, Kyathanahalli; Kooistra, Linda H; Nolte, Thomas; Szabo, Kathleen A; Willson, Gabrielle A; Wolf, Jeffrey C; Malarkey, David E

2017-01-01

The 2016 annual National Toxicology Program Satellite Symposium, entitled "Pathology Potpourri" was held in San Diego, CA, at the Society of Toxicologic Pathology's (STP) 35th annual meeting. The goal of this symposium was to present and discuss challenging diagnostic pathology and/or nomenclature issues. This article presents summaries of the speakers' talks, along with select images that were used by the audience for voting and discussion. Some lesions and topics covered during the symposium included malignant glioma and histiocytic sarcoma in the rodent brain; a new statistical method designed for histopathology data evaluation; uterine stromal/glandular polyp in a rat; malignant plasma cell tumor in a mouse brain; Schwann cell proliferative lesions in rat hearts; axillary schwannoma in a cat; necrosis and granulomatous inflammation in a rat brain; adenoma/carcinoma in a rat adrenal gland; hepatocyte maturation defect and liver/spleen hematopoietic defects in an embryonic mouse; distinguishing malignant glioma, malignant mixed glioma, and malignant oligodendroglioma in the rat; comparison of mammary gland whole mounts and histopathology from mice; and discussion of the International Harmonization of Nomenclature and Diagnostic Criteria collaborations.

Cux1 and Cux2 regulate dendritic branching, spine morphology and synapses of the upper layer neurons of the cortex

PubMed Central

Cubelos, Beatriz; Sebastián-Serrano, Alvaro; Beccari, Leonardo; Calcagnotto, Maria Elisa; Cisneros, Elsa; Kim, Seonhee; Dopazo, Ana; Alvarez-Dolado, Manuel; Redondo, Juan Miguel; Bovolenta, Paola; Walsh, Christopher A.; Nieto, Marta

2010-01-01

Summary Dendrite branching and spine formation determines the function of morphologically distinct and specialized neuronal subclasses. However, little is known about the programs instructing specific branching patterns in vertebrate neurons and whether such programs influence dendritic spines and synapses. Using knockout and knockdown studies combined with morphological, molecular and electrophysiological analysis we show that the homeobox Cux1 and Cux2 are intrinsic and complementary regulators of dendrite branching, spine development and synapse formation in layer II–III neurons of the cerebral cortex. Cux genes control the number and maturation of dendritic spines partly through direct regulation of the expression of Xlr3b and Xlr4b, chromatin remodeling genes previously implicated in cognitive defects. Accordingly, abnormal dendrites and synapses in Cux2−/− mice correlate with reduced synaptic function and defects in working memory. These demonstrate critical roles of Cux in dendritogenesis and highlight novel subclass-specific mechanisms of synapse regulation that contribute to the establishment of cognitive circuits. PMID:20510857

Adsorption and Reaction of Acetaldehyde on Shape-Controlled CeO2 Nanocrystals: Elucidation of Structure-function Relationships

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mann, Amanda K; Wu, Zili; Calaza, Florencia

2014-01-01

CeO2 cubes with {100} facets, octahedra with {111} facets, and wires with highly defective structures were utilized to probe the structure-dependent reactivity of acetaldehyde. Using temperature-programmed desorption (TPD), temperature-programmed surface reactions (TPSR), and in situ infrared spectroscopy it was found that acetaldehyde desorbs unreacted or undergoes reduction, coupling, or C-C bond scission reactions depending on the surface structure of CeO2. Room temperature FTIR indicates that acetaldehyde binds primarily as 1-acetaldehyde on the octahedra, in a variety of conformations on the cubes, including coupling products and acetate and enolate species, and primarily as coupling products on the wires. The percent consumptionmore » of acetaldehyde follows the order of wires > cubes > octahedra. All the nanoshapes produce the coupling product crotonaldehyde; however, the selectivity to produce ethanol follows the order wires cubes >> octahedra. The selectivity and other differences can be attributed to the variation in the basicity of the surfaces, defects densities, coordination numbers of surface atoms, and the reducibility of the nanoshapes.« less

Study of interaction among silicon, lithium, oxygen and radiation-induced defects for radiation-hardened solar cells

NASA Technical Reports Server (NTRS)

Berman, P. A.

1973-01-01

In order to improve reliability and the useful lifetime of solar cell arrays for space use, a program was undertaken to develop radiation-hardened lithium-doped silicon solar cells. These cells were shown to be significantly more resistant to degradation by ionized particles than the presently used n-p nonlithium-doped silicon solar cells. The results of various analyses performed to develop a more complete understanding of the physics of the interaction among lithium, silicon, oxygen, and radiation-induced defects are presented. A discussion is given of those portions of the previous model of radiation damage annealing which were found to be in error and those portions which were upheld by these extensive investigations.

ProFile Vortex and Vortex Blue Nickel-Titanium Rotary Instruments after Clinical Use.

PubMed

Shen, Ya; Zhou, Huimin; Coil, Jeffrey M; Aljazaeri, Bassim; Buttar, Rene; Wang, Zhejun; Zheng, Yu-feng; Haapasalo, Markus

2015-06-01

The aim of this study was to analyze the incidence and mode of ProFile Vortex and Vortex Blue instrument defects after clinical use in a graduate endodontic program and to examine the impact of clinical use on the instruments' metallurgical properties. A total of 330 ProFile Vortex and 1136 Vortex Blue instruments from the graduate program were collected after each had been used in 3 teeth. The incidence and type of instrument defects were analyzed. The lateral surfaces and fracture surfaces of the fractured files were examined by using scanning electron microscopy. Unused and used instruments were examined by full and partial differential scanning calorimetry. No fractures were observed in the 330 ProFile Vortex instruments, whereas 20 (6.1%) revealed bent or blunt defects. Only 2 of the 1136 Vortex Blue files fractured during clinical use. The cause of fracture was shear stress. The fractures occurred at the tip end of the spirals. Only 1.8% (21 of 1136) of the Vortex Blue files had blunt tips. Austenite-finish temperatures were very similar for unused and used ProFile Vortex files and were all greater than 50°C. The austenite-finish temperatures of used and unused Vortex Blue files (38.5°C) were lower than those in ProFile Vortex instruments (P < .001). However, the transformation behavior of Vortex Blue files had an obvious 2-stage transformation, martensite-to-R phase and R-to-austenite phase. The trends of differential scanning calorimetry plots of unused Vortex Blue instruments and clinically used instruments were very similar. The risk of ProFile Vortex and Vortex Blue instrument fracture is very low when instruments are discarded after clinical use in the graduate endodontic program. The Vortex Blue files have metallurgical behavior different from ProFile Vortex instruments. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Evidence That Masking of Synapsis Imperfections Counterbalances Quality Control to Promote Efficient Meiosis

PubMed Central

Mlynarczyk-Evans, Susanna; Roelens, Baptiste; Villeneuve, Anne M.

2013-01-01

Reduction in ploidy to generate haploid gametes during sexual reproduction is accomplished by the specialized cell division program of meiosis. Pairing between homologous chromosomes and assembly of the synaptonemal complex at their interface (synapsis) represent intermediate steps in the meiotic program that are essential to form crossover recombination-based linkages between homologs, which in turn enable segregation of the homologs to opposite poles at the meiosis I division. Here, we challenge the mechanisms of pairing and synapsis during C. elegans meiosis by disrupting the normal 1∶1 correspondence between homologs through karyotype manipulation. Using a combination of cytological tools, including S-phase labeling to specifically identify X chromosome territories in highly synchronous cohorts of nuclei and 3D rendering to visualize meiotic chromosome structures and organization, our analysis of trisomic (triplo-X) and polyploid meiosis provides insight into the principles governing pairing and synapsis and how the meiotic program is “wired” to maximize successful sexual reproduction. We show that chromosomes sort into homologous groups regardless of chromosome number, then preferentially achieve pairwise synapsis during a period of active chromosome mobilization. Further, comparisons of synapsis configurations in triplo-X germ cells that are proficient or defective for initiating recombination suggest a role for recombination in restricting chromosomal interactions to a pairwise state. Increased numbers of homologs prolong markers of the chromosome mobilization phase and/or boost germline apoptosis, consistent with triggering quality control mechanisms that promote resolution of synapsis problems and/or cull meiocytes containing synapsis defects. However, we also uncover evidence for the existence of mechanisms that “mask” defects, thus allowing resumption of prophase progression and survival of germ cells despite some asynapsis. We propose that coupling of saturable masking mechanisms with stringent quality controls maximizes meiotic success by making progression and survival dependent on achieving a level of synapsis sufficient for crossover formation without requiring perfect synapsis. PMID:24339786

DEFECTIVE TRAFFICKING OF CONE PHOTORECEPTOR CNG CHANNELS INDUCES THE UNFOLDED PROTEIN RESPONSE AND ER STRESS-ASSOCIATED CELL DEATH

PubMed Central

Duricka, Deborah L.; Brown, R. Lane; Varnum, Michael D.

2011-01-01

SYNOPSIS Mutations that perturb the function of photoreceptor cyclic nucleotide-gated (CNG) channels are associated with several human retinal disorders, but the molecular and cellular mechanisms leading to photoreceptor dysfunction and degeneration remain unclear. Many loss-of-function mutations result in intracellular accumulation of CNG channel subunits. Accumulation of proteins in the endoplasmic reticulum (ER) is known to cause ER stress and trigger the unfolded protein response (UPR), an evolutionarily conserved cellular program that results in either adaptation via increased protein processing capacity or apoptotic cell death. We hypothesize that defective trafficking of cone photoreceptor CNG channels can induce UPR-mediated cell death. To test this idea, CNGA3 subunits bearing the R563H and Q655X mutations were expressed in photoreceptor-derived 661W cells with CNGB3 subunits. Compared to wild type, R563H and Q655X subunits displayed altered degradation rates and/or were retained in the ER. ER retention was associated with increased expression of UPR-related markers of ER stress and with decreased cell viability. Chemical and pharmacological chaperones (TUDCA, 4PBA, and the cGMP analog CPT-cGMP) differentially reduced degradation and/or promoted plasma-membrane localization of defective subunits. Improved subunit maturation was concordant with reduced expression of ER stress markers and improved viability of cells expressing localization-defective channels. These results indicate that ER stress can arise from expression of localization defective CNG channels, and may represent a contributing factor for photoreceptor degeneration. PMID:21992067

Shared molecular networks in orofacial and neural tube development.

PubMed

Kousa, Youssef A; Mansour, Tamer A; Seada, Haitham; Matoo, Samaneh; Schutte, Brian C

2017-01-30

Single genetic variants can affect multiple tissues during development. Thus it is possible that disruption of shared gene regulatory networks might underlie syndromic presentations. In this study, we explore this idea through examination of two critical developmental programs that control orofacial and neural tube development and identify shared regulatory factors and networks. Identification of these networks has the potential to yield additional candidate genes for poorly understood developmental disorders and assist in modeling and perhaps managing risk factors to prevent morbidly and mortality. We reviewed the literature to identify genes common between orofacial and neural tube defects and development. We then conducted a bioinformatic analysis to identify shared molecular targets and pathways in the development of these tissues. Finally, we examine publicly available RNA-Seq data to identify which of these genes are expressed in both tissues during development. We identify common regulatory factors in orofacial and neural tube development. Pathway enrichment analysis shows that folate, cancer and hedgehog signaling pathways are shared in neural tube and orofacial development. Developing neural tissues differentially express mouse exencephaly and cleft palate genes, whereas developing orofacial tissues were enriched for both clefting and neural tube defect genes. These data suggest that key developmental factors and pathways are shared between orofacial and neural tube defects. We conclude that it might be most beneficial to focus on common regulatory factors and pathways to better understand pathology and develop preventative measures for these birth defects. Birth Defects Research 109:169-179, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Program Manager: The Journal of the Defense Systems Management College. Volume 13, Number 2, March-April 1984,

DTIC Science & Technology

1984-04-01

tractor’s price proposal and ag - I am in almost complete agreement gressively negotiate a fair and o with Commander Sellers’ counter- reasonable price. point...systems is reflected nance passes to the government, ex- .’, " in a shift of policy toward in- cept for latent defects, meaning those .- P creased use...T-bills, and the rate has Therefore, NPV cannot be used by it- I would recommend that program hovered around 10 percent lately. self , but must be

Population-Based Microcephaly Surveillance in the United States, 2009 to 2013: An Analysis of Potential Sources of Variation

PubMed Central

Cragan, Janet D.; Isenburg, Jennifer L.; Parker, Samantha E.; Alverson, C.J.; Meyer, Robert E.; Stallings, Erin B.; Kirby, Russell S.; Lupo, Philip J.; Liu, Jennifer S.; Seagroves, Amanda; Ethen, Mary K.; Cho, Sook Ja; Evans, MaryAnn; Liberman, Rebecca F.; Fornoff, Jane; Browne, Marilyn L.; Rutkowski, Rachel E.; Nance, Amy E.; Anderka, Marlene; Fox, Deborah J.; Steele, Amy; Copeland, Glenn; Romitti, Paul A.; Mai, Cara T.

2017-01-01

Background Congenital microcephaly has been linked to maternal Zika virus infection. However, ascertaining infants diagnosed with microcephaly can be challenging. Methods Thirty birth defects surveillance programs provided data on infants diagnosed with microcephaly born 2009 to 2013. The pooled prevalence of microcephaly per 10,000 live births was estimated overall and by maternal/infant characteristics. Variation in prevalence was examined across case finding methods. Nine programs provided data on head circumference and conditions potentially contributing to microcephaly. Results The pooled prevalence of microcephaly was 8.7 per 10,000 live births. Median prevalence (per 10,000 live births) was similar among programs using active (6.7) and passive (6.6) methods; the interdecile range of prevalence estimates was wider among programs using passive methods for all race/ethnicity categories except Hispanic. Prevalence (per 10,000 live births) was lowest among non-Hispanic Whites (6.5) and highest among non-Hispanic Blacks and Hispanics (11.2 and 11.9, respectively); estimates followed a U-shaped distribution by maternal age with the highest prevalence among mothers <20 years (11.5) and ≥40 years (13.2). For gestational age and birth weight, the highest prevalence was among infants <32 weeks gestation and infants <1500 gm. Case definitions varied; 41.8% of cases had an HC ≥ the 10th percentile for sex and gestational age. Conclusion Differences in methods, population distribution of maternal/infant characteristics, and case definitions for microcephaly can contribute to the wide range of observed prevalence estimates across individual birth defects surveillance programs. Addressing these factors in the setting of Zika virus infection can improve the quality of prevalence estimates. PMID:27891783

Progress Toward Modeling Spectroscopic Signatures of Mix on Omega and NIF

NASA Astrophysics Data System (ADS)

Tregillis, I. L.; Schmitt, M. J.; Hsu, S. C.; Wysocki, F. J.; Cobble, J. A.; Murphy, T. J.

2011-10-01

Defect-induced mix processes may degrade the performance of ICF and ICF-like targets at Omega and NIF. An improved understanding of the relevant physics requires an experimental program built on a foundation of radiation-hydrodynamic simulations plus reliable synthetic diagnostic outputs. To that end, the Applications of Ignition (AoI) and Defect Implosion Experiment (DIME) efforts at LANL have focused on directly driven plastic capsules containing high-Z dopants and manufactured with an equatorial ``trench'' defect. One of the key diagnostic techniques for detecting and diagnosing the migration of dopant material into the hot core is Multi-Monochromatic X-ray Imaging (MMI). This talk will focus on recent efforts to model spectroscopic signatures of mix processes in AoI/DIME capsules via simulated MMI-type diagnostic instruments. It will also include data from recent Omega shots and calculations in support of Tier 1 experiments at NIF in FY2012. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Application of pattern recognition techniques to acousto-ultrasonic testing of Kevlar composite panels

NASA Astrophysics Data System (ADS)

Hinton, Yolanda L.

An acousto-ultrasonic evaluation of panels fabricated from woven Kevlar and PVB/phenolic resin is being conducted. The panels were fabricated with various simulated defects. They were examined by pulsing with one acoustic emission sensor, and detecting the signal with another sensor, on the same side of the panel at a fixed distance. The acoustic emission signals were filtered through high (400-600 KHz), low (100-300 KHz) and wide (100-1200 KHz) bandpass filters. Acoustic emission signal parameters, including amplitude, counts, rise time, duration, 'energy', rms, and counts to peak, were recorded. These were statistically analyzed to determine which of the AE parameters best characterize the simulated defects. The wideband filtered acoustic emission signal was also digitized and recorded for further processing. Seventy-one features of the signals in both the time and frequency domains were calculated and compared to determine which subset of these features uniquely characterize the defects in the panels. The objective of the program is to develop a database of AE signal parameters and features to be used in pattern recognition as an inspection tool for material fabricated from these materials.

Nutrition and growth in congenital heart disease: a challenge in children.

PubMed

Medoff-Cooper, Barbara; Ravishankar, Chitra

2013-03-01

Growth failure secondary to feeding problems after complex neonatal cardiac surgery is well documented, but not well understood. The purpose of this review is to describe feeding and growth pattern in children with congenital heart defects. Nearly half of the infants with univentricular heart defects require supplementation with nasogastric or gastrostomy tube at discharge from neonatal surgery. Feeding challenges contribute to parental stress, and persist beyond infancy. These infants are 'stunted' with both weight and height being below normal. Nearly a quarter of these infants meet the definition of 'failure to thrive' in the first year of life. Short stature is a significant problem for many of these children, and has an impact on neurodevelopmental outcomes. A structured nutritional program can have a positive impact on growth in the interstage period prior to the superior cavopulmonary connection. Optimizing nutritional intake has been targeted as a key component of the National Pediatric Cardiology Quality Improvement Collaborative. This initiative has enabled the development of best practices that have the potential to mitigate poor growth in children with congenital heart defects.

High-frequency EPR of surface impurities on nanodiamond

NASA Astrophysics Data System (ADS)

Peng, Zaili; Stepanov, Viktor; Takahashi, Susumu

Diamond is a fascinating material, hosting nitrogen-vacancy (NV) defect centers with unique magnetic and optical properties. There have been many reports that suggest the existence of paramagnetic impurities near surface of various kinds of diamonds. Electron paramagnetic resonance (EPR) investigation of mechanically crushed nanodiamonds (NDs) as well as detonation NDs revealed g 2 like signals that are attributed to structural defects and dangling bonds near the diamond surface. In this presentation, we investigate paramagnetic impurities in various sizes of NDs using high-frequency (HF) continuous wave (cw) and pulsed EPR spectroscopy. Strong size dependence on the linewidth of HF cw EPR spectra reveals the existence of paramagnetic impurities in the vicinity of the diamond surface. We also study the size dependence of the spin-lattice and spin-spin relaxation times (T1 and T2) of single substitutional nitrogen defects in NDs Significant deviations from the temperature dependence of the phonon-assisted T1 process were observed in the ND samples, and were attributed to the contribution from the surface impurities. This work was supported by the Searle Scholars Program and the National Science Foundation (DMR-1508661 and CHE-1611134).

High-throughput behavioral screening method for detecting auditory response defects in zebrafish.

PubMed

Bang, Pascal I; Yelick, Pamela C; Malicki, Jarema J; Sewell, William F

2002-08-30

We have developed an automated, high-throughput behavioral screening method for detecting hearing defects in zebrafish. Our assay monitors a rapid escape reflex in response to a loud sound. With this approach, 36 adult zebrafish, restrained in visually isolated compartments, can be simultaneously assessed for responsiveness to near-field 400 Hz sinusoidal tone bursts. Automated, objective determinations of responses are achieved with a computer program that obtains images at precise times relative to the acoustic stimulus. Images taken with a CCD video camera before and after stimulus presentation are subtracted to reveal a response to the sound. Up to 108 fish can be screened per hour. Over 6500 fish were tested to validate the reliability of the assay. We found that 1% of these animals displayed hearing deficits. The phenotypes of non-responders were further assessed with radiological analysis for defects in the gross morphology of the auditory system. Nearly all of those showed abnormalities in conductive elements of the auditory system: the swim bladder or Weberian ossicles. Copyright 2002 Elsevier Science B.V.

Fracture resistance of welded thick-walled high-pressure vessels in power plants. Report No. 2. Approach to evaluating static strength

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorynin, I.V.; Filatov, V.M.; Ignatov, V.A.

1986-07-01

The authors examine data on the effect of defects on the fracture resistance of high-pressure vessels and their models obtained within the framework of the HSST program. Results of internal-pressure tests of two types of vessels with a wall thickness of 152 mm made from forgings of steels SA508 and SA533, as well as small vessels with a wall thickness of 11.5 and 23mm made of steel SA533 are shown. The authors state that testing thick-walled welded high-pressure vessels and thin-walled vessels with surface defects of different sizes has demonstrated that there are substantial static-strength reserves in structures designed bymore » existing domestic and foreign standards on the strength of power-plant equipment. A correction was proposed for the presently used method of calculating the resistance of highpressure vessels to brittle fracture that allows for the dimensions of the defects in relation to the type of vessel, the manufacturing technology, and the method of inspection.« less

Electronic and energetics properties of oxygen defects in La2-xSrxCuO4 in relation to doping and strain

NASA Astrophysics Data System (ADS)

Park, Sohee; Park, Changwon; Yoon, Mina

The level of oxygen defects in La2-xSrxCuO4 (LSCO), a high temperature superconductor, is known to drastically change LSCO's structural and electronic properties. However, the atomistic understanding of the role of oxygen defects is far from being complete. Using first-principles calculations, we investigated the electronic and energetic properties of oxygen vacancies in LSCO in relation to external parameters such as degree of Sr doping amount and external strain. We find that the relative stabilities between the equatorial vacancy induced in the CuO2 layer and the apical vacancy in the LaO layer can be altered by strain. In addition, Sr doping plays a crucial role in their relative stabilities. Therefore, the complex interplay between those key parameters essentially determines the overall oxygen density. Our finding can be instrumental in the experimental development of LSCO with desired oxygen density. Work supported by the LDRD Program of ORNL managed by UT-Battle, LLC, for the U.S. DOE.

Study on electrical defects level in single layer two-dimensional Ta2O5

NASA Astrophysics Data System (ADS)

Dahai, Li; Xiongfei, Song; Linfeng, Hu; Ziyi, Wang; Rongjun, Zhang; Liangyao, Chen; David, Wei Zhang; Peng, Zhou

2016-04-01

Two-dimensional atomic-layered material is a recent research focus, and single layer Ta2O5 used as gate dielectric in field-effect transistors is obtained via assemblies of Ta2O5 nanosheets. However, the electrical performance is seriously affected by electronic defects existing in Ta2O5. Therefore, spectroscopic ellipsometry is used to calculate the transition energies and corresponding probabilities for two different charged oxygen vacancies, whose existence is revealed by x-ray photoelectron spectroscopy analysis. Spectroscopic ellipsometry fitting also calculates the thickness of single layer Ta2O5, exhibiting good agreement with atomic force microscopy measurement. Nondestructive and noncontact spectroscopic ellipsometry is appropriate for detecting the electrical defects level of single layer Ta2O5. Project supported by the National Natural Science Foundation of China (Grant Nos. 11174058 and 61376093), the Fund from Shanghai Municipal Science and Technology Commission (Grant No. 13QA1400400), the National Science and Technology Major Project, China (Grant No. 2011ZX02707), and the Innovation Program of Shanghai Municipal Education Commission (Grant No. 12ZZ010).

The ATM signaling network in development and disease.

PubMed

Stracker, Travis H; Roig, Ignasi; Knobel, Philip A; Marjanović, Marko

2013-01-01

The DNA damage response (DDR) rapidly recognizes DNA lesions and initiates the appropriate cellular programs to maintain genome integrity. This includes the coordination of cell cycle checkpoints, transcription, translation, DNA repair, metabolism, and cell fate decisions, such as apoptosis or senescence (Jackson and Bartek, 2009). DNA double-strand breaks (DSBs) represent one of the most cytotoxic DNA lesions and defects in their metabolism underlie many human hereditary diseases characterized by genomic instability (Stracker and Petrini, 2011; McKinnon, 2012). Patients with hereditary defects in the DDR display defects in development, particularly affecting the central nervous system, the immune system and the germline, as well as aberrant metabolic regulation and cancer predisposition. Central to the DDR to DSBs is the ataxia-telangiectasia mutated (ATM) kinase, a master controller of signal transduction. Understanding how ATM signaling regulates various aspects of the DDR and its roles in vivo is critical for our understanding of human disease, its diagnosis and its treatment. This review will describe the general roles of ATM signaling and highlight some recent advances that have shed light on the diverse roles of ATM and related proteins in human disease.

The ATM signaling network in development and disease

PubMed Central

Stracker, Travis H.; Roig, Ignasi; Knobel, Philip A.; Marjanović, Marko

2013-01-01

The DNA damage response (DDR) rapidly recognizes DNA lesions and initiates the appropriate cellular programs to maintain genome integrity. This includes the coordination of cell cycle checkpoints, transcription, translation, DNA repair, metabolism, and cell fate decisions, such as apoptosis or senescence (Jackson and Bartek, 2009). DNA double-strand breaks (DSBs) represent one of the most cytotoxic DNA lesions and defects in their metabolism underlie many human hereditary diseases characterized by genomic instability (Stracker and Petrini, 2011; McKinnon, 2012). Patients with hereditary defects in the DDR display defects in development, particularly affecting the central nervous system, the immune system and the germline, as well as aberrant metabolic regulation and cancer predisposition. Central to the DDR to DSBs is the ataxia-telangiectasia mutated (ATM) kinase, a master controller of signal transduction. Understanding how ATM signaling regulates various aspects of the DDR and its roles in vivo is critical for our understanding of human disease, its diagnosis and its treatment. This review will describe the general roles of ATM signaling and highlight some recent advances that have shed light on the diverse roles of ATM and related proteins in human disease. PMID:23532176

Predicting neutron damage using TEM with in situ ion irradiation and computer modeling

NASA Astrophysics Data System (ADS)

Kirk, Marquis A.; Li, Meimei; Xu, Donghua; Wirth, Brian D.

2018-01-01

We have constructed a computer model of irradiation defect production closely coordinated with TEM and in situ ion irradiation of Molybdenum at 80 °C over a range of dose, dose rate and foil thickness. We have reexamined our previous ion irradiation data to assign appropriate error and uncertainty based on more recent work. The spatially dependent cascade cluster dynamics model is updated with recent Molecular Dynamics results for cascades in Mo. After a careful assignment of both ion and neutron irradiation dose values in dpa, TEM data are compared for both ion and neutron irradiated Mo from the same source material. Using the computer model of defect formation and evolution based on the in situ ion irradiation of thin foils, the defect microstructure, consisting of densities and sizes of dislocation loops, is predicted for neutron irradiation of bulk material at 80 °C and compared with experiment. Reasonable agreement between model prediction and experimental data demonstrates a promising direction in understanding and predicting neutron damage using a closely coordinated program of in situ ion irradiation experiment and computer simulation.

NRC/AMRMC Resident Research Associateship Program

DTIC Science & Technology

2015-03-01

antimicrobials (and antiseptics) as well as to evaluate the effectiveness of various biofilm dispersal agents utilizing a number of bacterial species as...combat related wounds. 3 Demonstrated the utility of combinations of biofilm dispersal agents and antimicrobials as an alternate therapy for...alone or in combination with antimicrobials ) to reduce infection in contaminated femoral segmental defects. 5 Characterized host responses of

Interdisciplinary Program for Quantitative Flaw Definition.

DTIC Science & Technology

1978-01-01

Ceramics .................... 284 UNIT C, TASK 4 - Microfocus X-Ray and Image Enhance- ment of Radiographic Data ....................... 292 UNIT C, TASK 5...Conventional Ultrasonic Inspection Methods Applied to Ceramics ..................... 294 iii 7! SC595.32SA OVERVIEW PROJECT I - QUANTITATIVE...parameters. Unit C was initiated in October of 1977 following encouraging nondestructive defect detectability studies in structural ceramics , using

Apollo experience report environmental acceptance testing

NASA Technical Reports Server (NTRS)

Laubach, C. H. M.

1976-01-01

Environmental acceptance testing was used extensively to screen selected spacecraft hardware for workmanship defects and manufacturing flaws. The minimum acceptance levels and durations and methods for their establishment are described. Component selection and test monitoring, as well as test implementation requirements, are included. Apollo spacecraft environmental acceptance test results are summarized, and recommendations for future programs are presented.

CARES/Life Ceramics Durability Evaluation Software Used for Mars Microprobe Aeroshell

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.

1998-01-01

The CARES/Life computer program, which was developed at the NASA Lewis Research Center, predicts the probability of a monolithic ceramic component's failure as a function of time in service. The program has many features and options for materials evaluation and component design. It couples commercial finite element programs-which resolve a component's temperature and stress distribution-to-reliability evaluation and fracture mechanics routines for modeling strength-limiting defects. These routines are based on calculations of the probabilistic nature of the brittle material's strength. The capability, flexibility, and uniqueness of CARES/Life has attracted many users representing a broad range of interests and has resulted in numerous awards for technological achievements and technology transfer.

Pharmacological correction of a defect in PPAR-gamma signaling ameliorates disease severity in Cftr-deficient mice.

PubMed

Harmon, Gregory S; Dumlao, Darren S; Ng, Damian T; Barrett, Kim E; Dennis, Edward A; Dong, Hui; Glass, Christopher K

2010-03-01

Cystic fibrosis is caused by mutations in the cystic fibrosis transmembrane conductance regulator (encoded by Cftr) that impair its role as an apical chloride channel that supports bicarbonate transport. Individuals with cystic fibrosis show retained, thickened mucus that plugs airways and obstructs luminal organs as well as numerous other abnormalities that include inflammation of affected organs, alterations in lipid metabolism and insulin resistance. Here we show that colonic epithelial cells and whole lung tissue from Cftr-deficient mice show a defect in peroxisome proliferator-activated receptor-gamma (PPAR-gamma, encoded by Pparg) function that contributes to a pathological program of gene expression. Lipidomic analysis of colonic epithelial cells suggests that this defect results in part from reduced amounts of the endogenous PPAR-gamma ligand 15-keto-prostaglandin E(2) (15-keto-PGE(2)). Treatment of Cftr-deficient mice with the synthetic PPAR-gamma ligand rosiglitazone partially normalizes the altered gene expression pattern associated with Cftr deficiency and reduces disease severity. Rosiglitazone has no effect on chloride secretion in the colon, but it increases expression of the genes encoding carbonic anhydrases 4 and 2 (Car4 and Car2), increases bicarbonate secretion and reduces mucus retention. These studies reveal a reversible defect in PPAR-gamma signaling in Cftr-deficient cells that can be pharmacologically corrected to ameliorate the severity of the cystic fibrosis phenotype in mice.

Failure Analysis of Cracked FS-85 Tubing and ASTAR-811C End Caps

DOE Office of Scientific and Technical Information (OSTI.GOV)

ME Petrichek

2006-02-09

Failure analyses were performed on cracked FS-85 tubing and ASTAR-811C and caps which had been fabricated as components of biaxial creep specimens meant to support materials testing for the NR Space program. During the failure analyses of cracked FS-85 tubing, it was determined that the failure potentially could be due to two effects: possible copper contamination from the EDM (electro-discharge machined) recast layer and/or an insufficient solution anneal. to prevent similar failures in the future, a more formal analysis should be done after each processing step to ensure the quality of the material before further processing. During machining of themore » ASTAR-811FC rod to form end caps for biaxial creep specimens, linear defects were observed along the center portion of the end caps. These defects were only found in material that was processed from the top portion of the ingot. The linear defects were attributed to a probable residual ingot pipe that was not removed from the ingot. During the subsequent processing of the ingot to rod, the processing temperatures were not high enough to allow self healing of the ingot's residual pipe defect. To prevent this from occurring in the future, it is necessary to ensure that complete removal of the as-melted ingot pipe is verified by suitable non-destructive evaluation (NDE).« less

Arabidopsis ribosomal proteins control vacuole trafficking and developmental programs through the regulation of lipid metabolism.

PubMed

Li, Ruixi; Sun, Ruobai; Hicks, Glenn R; Raikhel, Natasha V

2015-01-06

The vacuole is the most prominent compartment in plant cells and is important for ion and protein storage. In our effort to search for key regulators in the plant vacuole sorting pathway, ribosomal large subunit 4 (rpl4d) was identified as a translational mutant defective in both vacuole trafficking and normal development. Polysome profiling of the rpl4d mutant showed reduction in polysome-bound mRNA compared with wild-type, but no significant change in the general mRNA distribution pattern. Ribsomal profiling data indicated that genes in the lipid metabolism pathways were translationally down-regulated in the rpl4d mutant. Live imaging studies by Nile red staining suggested that both polar and nonpolar lipid accumulation was reduced in meristem tissues of rpl4d mutants. Pharmacological evidence showed that sterol and sphingolipid biosynthetic inhibitors can phenocopy the defects of the rpl4d mutant, including an altered vacuole trafficking pattern. Genetic evidence from lipid biosynthetic mutants indicates that alteration in the metabolism of either sterol or sphingolipid biosynthesis resulted in vacuole trafficking defects, similar to the rpl4d mutant. Tissue-specific complementation with key enzymes from lipid biosynthesis pathways can partially rescue both vacuole trafficking and auxin-related developmental defects in the rpl4d mutant. These results indicate that lipid metabolism modulates auxin-mediated tissue differentiation and endomembrane trafficking pathways downstream of ribosomal protein function.

Improving Stability of Zeolites in Aqueous Phase via Selective Removal of Structural Defects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prodinger, Sebastian; Derewinski, Miroslaw A.; Vjunov, Aleksei

2016-03-13

This work reports significant improvement in the hydrothermal stability of a well-characterized BEA zeolite via the selective removal of structural defects. Recent work suggests that the presence of silanol defects destabilizes the framework integrity of most zeolites and makes them susceptible to hydrolysis of the siloxy bonds by hot liquid water. The described approach allows for a key removal of silanols as shown with 29Si-MAS-NMR. Subsequently, the material stability in hot liquid water, measured by retention of its crystallinity with X-ray diffraction (XRD), is found to be superior to defective zeolites. In addition, N2-sorption measurements (BET) and transmission electron microscopymore » (TEM) show the formation of different types of mesoporosity for water-treated stabilized and unmodified materials. While the sorption capacity for untreated materials drops, related to re-precipitation of dissolved silica and pore blocking, the stabilized material retains its microporosity and improves its overall sorption capacity. The authors would like to thank B. W. Arey (PNNL) for HIM measurements and I. Arslan for TEM imaging. This work was supported by the U. S. Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. SP and MD acknowledge support by the Materials Synthesis and Simulation Across Scales (MS3 Initiative) conducted under Laboratory Directed Research & Development Program at PNNL.« less

Acceleration of Alveolar Ridge Augmentation Using a Low Dose of Recombinant Human Bone Morphogenetic Protein-2 Loaded on a Resorbable Bioactive Ceramic.

PubMed

Fahmy, Rania A; Mahmoud, Naguiba; Soliman, Samia; Nouh, Samir R; Cunningham, Larry; El-Ghannam, Ahmed

2015-12-01

The aim of the present study was to evaluate the effect of a porous silica-calcium phosphate composite (SCPC50) loaded with and without recombinant human bone morphogenetic protein-2 (rhBMP-2) on alveolar ridge augmentation in saddle-type defects. Micro-granules of SCPC50 resorbable bioactive ceramic were coated with rhBMP-2 10 mg and then implanted into a saddle-type defect (12 × 7 mm) in a dog mandible and covered with a collagen membrane. Control groups included defects grafted with SCPC50 granules without rhBMP-2 and un-grafted defects. Bone healing was evaluated at 8 and 16 weeks using histologic and histomorphometric techniques. The increase in bone height and total defect fill were assessed for each specimen using the ImageJ 1.46 program. The release kinetics of rhBMP-2 was determined in vitro. The height of the bone in the grafted defects and the total defect fill were statistically analyzed. SCPC50 enhanced alveolar ridge augmentation as indicated by the increased vertical bone height, bone surface area, and bone volume after 16 weeks. SCPC50-rhBMP-2 provided a sustained release profile of a low effective dose (BMP-2 4.6 ± 1.34 pg/mL per hour) during the 1- to 21-day period. The slow rate of release of rhBMP-2 from SCPC50 accelerated synchronized complete bone regeneration and graft material resorption in 8 weeks. Successful rapid reconstruction of the alveolar ridge by SCPC50 and SCPC50-rhBMP-2 occurred without any adverse excessive bone formation, inflammation, or fluid-filled voids. Results of this study suggest that SCPC50 is an effective graft material to preserve the alveolar ridge after tooth extraction. Coating SCPC50-rhBMP-2 further accelerated bone regeneration and a considerable increase in vertical bone height. These findings make SCPC50 the primary choice as a carrier for rhBMP-2. SCPC50-rhBMP-2 can serve as an alternative to autologous bone grafting. Published by Elsevier Inc.

Defect printability for high-exposure dose advanced packaging applications

NASA Astrophysics Data System (ADS)

Mikles, Max; Flack, Warren; Nguyen, Ha-Ai; Schurz, Dan

2003-12-01

Pellicles are used in semiconductor lithography to minimize printable defects and reduce reticle cleaning frequency. However, there are a growing number of microlithography applications, such as advanced packaging and nanotechnology, where it is not clear that pellicles always offer a significant benefit. These applications have relatively large critical dimensions and require ultra thick photoresists with extremely high exposure doses. Given that the lithography is performed in Class 100 cleanroom conditions, it is possible that the risk of defects from contamination is sufficiently low that pellicles would not be required on certain process layer reticles. The elimination of the pellicle requirement would provide a cost reduction by saving the original pellicle cost and eliminating future pellicle replacement and repair costs. This study examines the imaging potential of defects with reticle patterns and processes typical for gold-bump and solder-bump advanced packaging lithography. The test reticle consists of 30 to 90 μm octagonal contact patterns representative of advanced packaging reticles. Programmed defects are added that represent the range of particle sizes (3 to 30 μm) normally protected by the pellicle and that are typical of advanced packaging lithography cleanrooms. The reticle is exposed using an Ultratech Saturn Spectrum 300e2 1X stepper on wafers coated with a variety of ultra thick (30 to 100 μm) positive and negative-acting photoresists commonly used in advanced packaging. The experimental results show that in many cases smaller particles continue to be yield issues for the feature size and density typical of advanced packaging processes. For the two negative photoresists studied it appears that a pellicle is not required for protection from defects smaller than 10 to 15 μm depending on the photoresist thickness. Thus the decision on pellicle usage for these materials would need to be made based on the device fabrication process and the cleanliness of a fabrication facility. For the two positive photoresists studied it appears that a pellicle is required to protect from defects down to 3 μm defects depending on the photoresist thickness. This suggests that a pellicle should always be used for these materials. Since a typical fabrication facility would use both positive and negative photoresists it may be advantageous to use pellicles on all reticles simply to avoid confusion. The cost savings of not using a pellicle could easily be outweighed by the yield benefits of using one.

Development of Educational Support System for Learning Image Processing Enabling Client-Side Programming Aided by Java Servlet Technology

NASA Astrophysics Data System (ADS)

Furukawa, Tatsuya; Aoki, Noriyuki; Ohchi, Masashi; Nakao, Masaki

The image proccessing has become a useful and important technology in various reserch and development fields. According to such demands for engineering problems, we have designed and implemented the educational support system for that using a Java Applet technology. However in the conventional system, it required the tedious procedure for the end user to code his own programs. Therefore, in this study, we have improved the defect in the previous system by using a Java Servlet technology. The new system will make it possible for novice user to experience a practical digital image proccessing and an advanced programming with ease. We will describe the architecture of the proposed system function, that has been introduced to facilitate the client-side programming.

Total quality management - It works for aerospace information services

NASA Technical Reports Server (NTRS)

Erwin, James; Eberline, Carl; Colquitt, Wanda

1993-01-01

Today we are in the midst of information and 'total quality' revolutions. At the NASA STI Program's Center for AeroSpace Information (CASI), we are focused on using continuous improvements techniques to enrich today's services and products and to ensure that tomorrow's technology supports the TQM-based improvement of future STI program products and services. The Continuous Improvements Program at CASI is the foundation for Total Quality Management in products and services. The focus is customer-driven; its goal, to identify processes and procedures that can be improved and new technologies that can be integrated with the processes to gain efficiencies, provide effectiveness, and promote customer satisfaction. This Program seeks to establish quality through an iterative defect prevention approach that is based on the incorporation of standards and measurements into the processing cycle.

DPL-1 DP, LIN-35 Rb and EFL-1 E2F act with the MCD-1 zinc-finger protein to promote programmed cell death in Caenorhabditis elegans.

PubMed

Reddien, Peter W; Andersen, Erik C; Huang, Michael C; Horvitz, H Robert

2007-04-01

The genes egl-1, ced-9, ced-4, and ced-3 play major roles in programmed cell death in Caenorhabditis elegans. To identify genes that have more subtle activities, we sought mutations that confer strong cell-death defects in a genetically sensitized mutant background. Specifically, we screened for mutations that enhance the cell-death defects caused by a partial loss-of-function allele of the ced-3 caspase gene. We identified mutations in two genes not previously known to affect cell death, dpl-1 and mcd-1 (modifier of cell death). dpl-1 encodes the C. elegans homolog of DP, the human E2F-heterodimerization partner. By testing genes known to interact with dpl-1, we identified roles in cell death for four additional genes: efl-1 E2F, lin-35 Rb, lin-37 Mip40, and lin-52 dLin52. mcd-1 encodes a novel protein that contains one zinc finger and that is synthetically required with lin-35 Rb for animal viability. dpl-1 and mcd-1 act with efl-1 E2F and lin-35 Rb to promote programmed cell death and do so by regulating the killing process rather than by affecting the decision between survival and death. We propose that the DPL-1 DP, MCD-1 zinc finger, EFL-1 E2F, LIN-35 Rb, LIN-37 Mip40, and LIN-52 dLin52 proteins act together in transcriptional regulation to promote programmed cell death.

The Spreading of Social Energy: How Exposure to Positive and Negative Social News Affects Behavior.

PubMed

Yao, Ziqing; Yu, Rongjun

2016-01-01

Social news, unlike video games or TV programs, conveys real-life interactions. Theoretically, social news in which people help or harm each other and violate rules should influence both prosocial and violation behaviors. In two experiments, we demonstrated the spreading effects of social news in a social interaction context emphasizing social conventions and a nonsocial interaction context emphasizing moral norms. Across the two studies, the results showed that positive social news increased cooperation (decreased defection) but had no effect on cheating, whereas negative social news increased cheating but with no change in cooperation (or defection). We conclude that there is a spreading impact of positive social news in the conventional norm domain and of negative social news in the moral norm domain.

The Spreading of Social Energy: How Exposure to Positive and Negative Social News Affects Behavior

PubMed Central

Yao, Ziqing; Yu, Rongjun

2016-01-01

Social news, unlike video games or TV programs, conveys real-life interactions. Theoretically, social news in which people help or harm each other and violate rules should influence both prosocial and violation behaviors. In two experiments, we demonstrated the spreading effects of social news in a social interaction context emphasizing social conventions and a nonsocial interaction context emphasizing moral norms. Across the two studies, the results showed that positive social news increased cooperation (decreased defection) but had no effect on cheating, whereas negative social news increased cheating but with no change in cooperation (or defection). We conclude that there is a spreading impact of positive social news in the conventional norm domain and of negative social news in the moral norm domain. PMID:27253877

Academic Outcomes in Children With Congenital Heart Defects: A Population-Based Cohort Study.

PubMed

Oster, Matthew E; Watkins, Stephanie; Hill, Kevin D; Knight, Jessica H; Meyer, Robert E

2017-02-01

Most studies evaluating neurocognitive outcomes in children with congenital heart defects (CHD) have focused on high-risk patients or used specialized, resource-intensive testing. To determine the association of CHD with academic outcomes and compare outcomes according to the severity of CHD, we linked state educational records with a birth defects registry and birth certificates. We performed a retrospective cohort study using data from the North Carolina Birth Defects Monitoring Program, North Carolina Department of Public Instruction, and North Carolina Department of Health and Human Services vital records. We performed logistic regression, adjusting for maternal education, race/ethnicity, enrollment in public pre-Kindergarten, and gestational age, to determine the association of CHD with not meeting standards on reading and math end-of-grade examinations in third grade in 2006 to 2012. Of 5624 subjects with CHD and 10 832 with no structural birth defects, 2807 (50%) and 6355 (59%) were linked, respectively. Children with CHD had 1.24× the odds of not meeting standards in either reading or math (95% confidence interval, 1.12-1.37), with 44.6% of children with CHD not meeting standards in at least one of these areas compared with 37.5% without CHD. Although children with both critical and noncritical CHD had poorer outcomes, those with critical CHD were significantly more likely to receive exceptional services compared with the noncritical group (adjusted odds ratio, 1.46; 95% confidence interval, 1.15-1.86). Children with all types of CHD have poorer academic outcomes compared with their peers. Evaluation for exceptional services should be considered in children with any type of CHD. © 2017 American Heart Association, Inc.

Intrinsic SiO{sub x}-based unipolar resistive switching memory. II. Thermal effects on charge transport and characterization of multilevel programing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Yao-Feng, E-mail: yfchang@utexas.edu; Chen, Ying-Chen; Chen, Yen-Ting

2014-07-28

Multilevel programing and charge transport characteristics of intrinsic SiO{sub x}-based resistive switching memory are investigated using TaN/SiO{sub x}/n{sup ++}Si (MIS) and TiW/SiO{sub x}/TiW (MIM) device structures. Current transport characteristics of high- and low-resistance states (HRS and LRS) are studied in both device structures during multilevel operation. Analysis of device thermal response demonstrates that the effective electron energy barrier is strongly dependent on the resistance of the programed state, with estimates of 0.1 eV in the LRS and 0.6 eV in the HRS. Linear data fitting and conductance analyses indicate Poole-Frenkel emission or hopping conductance in the low-voltage region, whereas Fowler-Nordheim (F-N) ormore » trap-assisted tunneling (TAT) is indicated at moderate voltage. Characterizations using hopping transport lead to hopping distance estimates of ∼1 nm in the LRS for both device structures. Relative permittivity values (ε{sub r}) were extracted using the Poole-Frenkel formulism and estimates of local filament temperature, where ε{sub r} values were ∼80 in the LRS and ∼4 in the HRS, suggesting a strongly polarized medium in the LRS. The onset of F-N tunneling or TAT corresponds to an observed “overshoot” in the I-V response with an estimated threshold of 1.6 ± 0.2 V, in good agreement with reported electro-luminescence results for LRS devices. Resistive switching is discussed in terms of electrochemical reactions between common SiO{sub 2} defects, and specific defect energy levels are assigned to the dominant transitions in the I-V response. The overshoot response in the LRS is consistent with TAT through either the Eγ' oxygen vacancy or the hydrogen bridge defect, both of which are reported to have an effective bandgap of 1.7 eV. The SET threshold at ∼2.5 V is modeled as hydrogen release from the (Si-H){sub 2} defect to generate the hydrogen bridge, and the RESET transition is modeled as an electrochemical reaction that re-forms (SiH){sub 2}. The results provide further insights into charge transport and help identify potential switching mechanisms in SiO{sub x}-based unipolar resistive switching memory.« less

Preliminary Full-Scale Tests of the Center for Automated Processing of Hardwoods' Auto-Image

Treesearch

Philip A. Araman; Janice K. Wiedenbeck

1995-01-01

Automated lumber grading and yield optimization using computer controlled saws will be plausible for hardwoods if and when lumber scanning systems can reliably identify all defects by type. Existing computer programs could then be used to grade the lumber, identify the best cut-up solution, and control the sawing machines. The potential value of a scanning grading...

HgCdTe Surface and Defect Study Program.

DTIC Science & Technology

1984-07-01

double layer heterojunction (DLHJ) devices. There are however many complications on this once we consider implanted junctions, LWIR devices or even the...It is not possible from this measurement to discriminate between real interface states and charge nonuniformities . Admittance spectroscopy (discussed...earlier) and deep level transient spectroscopy (DLTS) are not usually affected by these nonuniformities due to their observation of a speci- fic

NRC/AMRMC Resident Research Associateship Program

DTIC Science & Technology

2015-03-01

antimicrobials (and antiseptics) as well as to evaluate the effectiveness of various biofilm dispersal agents utilizing a number of bacterial species as well...combat related wounds. 3 Demonstrated the utility of combinations of biofilm dispersal agents and antimicrobials as an alternate therapy for targeting...alone or in combination with antimicrobials ) to reduce infection in contaminated femoral segmental defects. 5 Characterized host responses of

Medical Services: Veterinary/Medical Food Inspection and Laboratory Service

DTIC Science & Technology

1997-11-06

cosmetics. (2) Laboratory diagnosis of communicable and zoonotic diseases and conditions of military interest. (3) Management of laboratory animal...veterinary food inspection service. (b) Prevention and control of communicable diseases of animals and zoonotic diseases and conditions. (c...Development of command zoonotic disease control programs. (2) Advise the MACOM of sanitary defects or epizootics that may be detected through the laboratory

75 FR 17333 - Addition of National Toxicology Program Carcinogens; Community Right-to-Know Toxic Chemical...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-06

... encryption, and be free of any defects or viruses. Docket: All documents in the docket are listed in the www... Community Right-to-Know Hotline, toll free at (800) 424-9346 or (703) 412-9810 in Virginia and Alaska or toll free, TDD (800) 553-7672, http://www.epa.gov/epaoswer/hotline/ . SUPPLEMENTARY INFORMATION: I...

29 CFR Appendix V to Part 1918 - Basic Elements of a First Aid Training Program (Non-mandatory)

Code of Federal Regulations, 2011 CFR

2011-07-01

...-mandatory) V Appendix V to Part 1918 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND...) Side Stress on Boom .66(b)(3)(i) Vessel's Permanent Equipment .55 Visible Defects .66(b)(3)(ii) Cups... Related Employments .2 River Towboat .2 Small Trimming Hatch .2 Vessel .2 Vessel's Cargo Handling Gear .2...

29 CFR Appendix V to Part 1918 - Basic Elements of a First Aid Training Program (Non-mandatory)

Code of Federal Regulations, 2012 CFR

2012-07-01

...-mandatory) V Appendix V to Part 1918 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND...) Side Stress on Boom .66(b)(3)(i) Vessel's Permanent Equipment .55 Visible Defects .66(b)(3)(ii) Cups... Related Employments .2 River Towboat .2 Small Trimming Hatch .2 Vessel .2 Vessel's Cargo Handling Gear .2...

Magnetic Domain Strain Sensor Program

DTIC Science & Technology

1990-08-01

metallic glass onto quartz and the CVD coated titanium were received from XiMagnetics. The coatings received from Damaskos initially appeared to be...successful but later proved defective in repeata- bility and reliability testing. The 8-inch-diameter metallic glass target that Damaskos was using...the backing plate. Scanning Electron Microscope (SEM) evaluations were done to confirm and evaluate the Damaskos coatings. 33 P-1121 :0313

Development of a 3D log sawing optimization system for small sawmills in central Appalachia, US

Treesearch

Wenshu Lin; Jingxin Wang; Edward Thomas

2011-01-01

A 3D log sawing optimization system was developed to perform log generation, opening face determination, sawing simulation, and lumber grading using 3D modeling techniques. Heuristic and dynamic programming algorithms were used to determine opening face and grade sawing optimization. Positions and shapes of internal log defects were predicted using a model developed by...

A Machine Vision System for Automatically Grading Hardwood Lumber - (Proceedings)

Treesearch

Richard W. Conners; Tai-Hoon Cho; Chong T. Ng; Thomas H. Drayer; Joe G. Tront; Philip A. Araman; Robert L. Brisbon

1990-01-01

Any automatic system for grading hardwood lumber can conceptually be divided into two components. One of these is a machine vision system for locating and identifying grading defects. The other is an automatic grading program that accepts as input the output of the machine vision system and, based on these data, determines the grade of a board. The progress that has...

A Demonstration Project of Speech Training for the Preschool Cleft Palate Child. Final Report.

ERIC Educational Resources Information Center

Harrison, Robert J.

To ascertain the efficacy of a program of language and speech stimulation for the preschool cleft palate child, a research and demonstration project was conducted using 137 subjects (ages 18 to 72 months) with defects involving the soft palate. Their language and speech skills were matched with those of a noncleft peer group revealing that the…

Integration of Computer-Based Virtual Check Ride System--Pre-Trip Inspection in Commercial Driver License Training Program

ERIC Educational Resources Information Center

Makwana, Alpesh P.

2009-01-01

"Pre-Trip Inspection" of the truck and trailer is one of the components of the current Commercial Driver's License (CDL) test. This part of the CDL test checks the ability of the student to identify the important parts of the commercial vehicle and their potential defects. The "Virtual Check Ride System" (VCRS), a…

Improvement of program to calculate electronic properties of narrow band gap materials

NASA Technical Reports Server (NTRS)

Patterson, James D.; Abdelhakiem, Wafaa

1991-01-01

The program was improved by reprogramming it so it will run on both a SUN and a VAX. Also it is easily transportable as it is on a disk for use on a SUN. A computer literature search resulted in some improved parameters for Hg(1-x)Cd(x)Te and a table of parameters for Hg(1-x)Zn(x)Te. The effects of neutral defects were added to the program, and it was found, as expected, that they contribute very little to the mobility at temperatures of interest. The effect were added of varying the following parameters: dielectric constants, screening parameters, disorder energies, donor and acceptor concentrations, momentum matrix element, different expressions for energy gap, and transverse effective charge.

Proximity to Pediatric Cardiac Surgical Care among Adolescents with Congenital Heart Defects in 11 New York Counties.

PubMed

Sommerhalter, Kristin M; Insaf, Tabassum Z; Akkaya-Hocagil, Tugba; McGarry, Claire E; Farr, Sherry L; Downing, Karrie F; Lui, George K; Zaidi, Ali N; Van Zutphen, Alissa R

2017-11-01

Many individuals with congenital heart defects (CHDs) discontinue cardiac care in adolescence, putting them at risk of adverse health outcomes. Because geographic barriers may contribute to cessation of care, we sought to characterize geographic access to comprehensive cardiac care among adolescents with CHDs. Using a population-based, 11-county surveillance system of CHDs in New York, we characterized proximity to the nearest pediatric cardiac surgical care center among adolescents aged 11 to 19 years with CHDs. Residential addresses were extracted from surveillance records documenting 2008 to 2010 healthcare encounters. Addresses were geocoded using ArcGIS and the New York State Street and Address Maintenance Program, a statewide address point database. One-way drive and public transit time from residence to nearest center were calculated using R packages gmapsdistance and rgeos with the Google Maps Distance Matrix application programming interface. A marginal model was constructed to identify predictors associated with one-way travel time. We identified 2522 adolescents with 3058 corresponding residential addresses and 12 pediatric cardiac surgical care centers. The median drive time from residence to nearest center was 18.3 min, and drive time was 30 min or less for 2475 (80.9%) addresses. Predicted drive time was longest for rural western addresses in high poverty census tracts (68.7 min). Public transit was available for most residences in urban areas but for few in rural areas. We identified areas with geographic barriers to surgical care. Future research is needed to determine how these barriers influence continuity of care among adolescents with CHDs. Birth Defects Research 109:1494-1503, 2017.© 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Prevention of birth defects in the pre-conception period: knowledge and practice of health care professionals (nurses and doctors) in a city of Southern Brazil

PubMed Central

Ferreira, Flávia Romariz; Russo Akiba, Heloisa Regina; Júnior, Edward Araujo; Figueiredo, Elisabeth Niglio; Abrahão, Anelise Riedel

2015-01-01

Background: Some congenital defects can be prevented in the pregestational stage. However, many health professionals are not prepared to provide counselling to couples regarding the same. Objective: This study aimed to assess the performance of doctors and nurses from a primary health-care unit in Florianopolis, Brazil, in preventing birth defects in the preconception period based on the recommendations of the Control Center of Disease Prevention. Materials and Methods: This descriptive cross sectional study was performed at a tertiary referral center. In this study, a semi-structured questionnaire was provided to 160 health professionals comprising doctors and nurses who were actively involved in providing primary health care in family health programs. The non-parametric Chi-square (χ2) test was used to analyse the data obtained through multiple choice questions. Results: Our results showed that although 81.9% of health professionals provided health-care assistance based on protocols, and only 46.2% professionals were aware of the presence of the topic in the protocol. Of the recommendations provided by the Control Center of Disease Prevention, the use of folic acid was the most prescribed. However, this prescription was not statistically different between nurses and doctors (P=0.85). Conclusion: This study identified the fragile nature in these professional’s knowledge about the prevention of birth defects in pre-conception period, as evidenced by the inconsistency in their responses. PMID:26644794

Arabidopsis ribosomal proteins control vacuole trafficking and developmental programs through the regulation of lipid metabolism

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Ruixi; Sun, Ruobai; Hicks, Glenn R.

The vacuole is the most prominent compartment in plant cells and is important for ion and protein storage. In our effort to search for key regulators in the plant vacuole sorting pathway, ribosomal large subunit 4 (rpl4d) was identified as a translational mutant defective in both vacuole trafficking and normal development. Polysome profiling of the rpl4d mutant showed reduction in polysome-bound mRNA compared with wild-type, but no significant change in the general mRNA distribution pattern. Ribsomal profiling data indicated that genes in the lipid metabolism pathways were translationally down-regulated in the rpl4d mutant. Live imaging studies by Nile red stainingmore » suggested that both polar and nonpolar lipid accumulation was reduced in meristem tissues of rpl4d mutants. Pharmacological evidence showed that sterol and sphingolipid biosynthetic inhibitors can phenocopy the defects of the rpl4d mutant, including an altered vacuole trafficking pattern. Genetic evidence from lipid biosynthetic mutants indicates that alteration in the metabolism of either sterol or sphingolipid biosynthesis resulted in vacuole trafficking defects, similar to the rpl4d mutant. Tissue-specific complementation with key enzymes from lipid biosynthesis pathways can partially rescue both vacuole trafficking and auxin-related developmental defects in the rpl4d mutant. These results indicate that lipid metabolism modulates auxin-mediated tissue differentiation and endomembrane trafficking pathways downstream of ribosomal protein function.« less

Arabidopsis ribosomal proteins control vacuole trafficking and developmental programs through the regulation of lipid metabolism

DOE PAGES

Li, Ruixi; Sun, Ruobai; Hicks, Glenn R.; ...

2014-12-22

The vacuole is the most prominent compartment in plant cells and is important for ion and protein storage. In our effort to search for key regulators in the plant vacuole sorting pathway, ribosomal large subunit 4 (rpl4d) was identified as a translational mutant defective in both vacuole trafficking and normal development. Polysome profiling of the rpl4d mutant showed reduction in polysome-bound mRNA compared with wild-type, but no significant change in the general mRNA distribution pattern. Ribsomal profiling data indicated that genes in the lipid metabolism pathways were translationally down-regulated in the rpl4d mutant. Live imaging studies by Nile red stainingmore » suggested that both polar and nonpolar lipid accumulation was reduced in meristem tissues of rpl4d mutants. Pharmacological evidence showed that sterol and sphingolipid biosynthetic inhibitors can phenocopy the defects of the rpl4d mutant, including an altered vacuole trafficking pattern. Genetic evidence from lipid biosynthetic mutants indicates that alteration in the metabolism of either sterol or sphingolipid biosynthesis resulted in vacuole trafficking defects, similar to the rpl4d mutant. Tissue-specific complementation with key enzymes from lipid biosynthesis pathways can partially rescue both vacuole trafficking and auxin-related developmental defects in the rpl4d mutant. These results indicate that lipid metabolism modulates auxin-mediated tissue differentiation and endomembrane trafficking pathways downstream of ribosomal protein function.« less

Apoptosis and Molecular Targeting Therapy in Cancer

PubMed Central

Hassan, Mohamed; Watari, Hidemichi; AbuAlmaaty, Ali; Ohba, Yusuke; Sakuragi, Noriaki

2014-01-01

Apoptosis is the programmed cell death which maintains the healthy survival/death balance in metazoan cells. Defect in apoptosis can cause cancer or autoimmunity, while enhanced apoptosis may cause degenerative diseases. The apoptotic signals contribute into safeguarding the genomic integrity while defective apoptosis may promote carcinogenesis. The apoptotic signals are complicated and they are regulated at several levels. The signals of carcinogenesis modulate the central control points of the apoptotic pathways, including inhibitor of apoptosis (IAP) proteins and FLICE-inhibitory protein (c-FLIP). The tumor cells may use some of several molecular mechanisms to suppress apoptosis and acquire resistance to apoptotic agents, for example, by the expression of antiapoptotic proteins such as Bcl-2 or by the downregulation or mutation of proapoptotic proteins such as BAX. In this review, we provide the main regulatory molecules that govern the main basic mechanisms, extrinsic and intrinsic, of apoptosis in normal cells. We discuss how carcinogenesis could be developed via defective apoptotic pathways or their convergence. We listed some molecules which could be targeted to stimulate apoptosis in different cancers. Together, we briefly discuss the development of some promising cancer treatment strategies which target apoptotic inhibitors including Bcl-2 family proteins, IAPs, and c-FLIP for apoptosis induction. PMID:25013758

The inclusion of ADA-SCID in expanded newborn screening by tandem mass spectrometry.

PubMed

la Marca, Giancarlo; Giocaliere, Elisa; Malvagia, Sabrina; Funghini, Silvia; Ombrone, Daniela; Della Bona, Maria Luisa; Canessa, Clementina; Lippi, Francesca; Romano, Francesca; Guerrini, Renzo; Resti, Massimo; Azzari, Chiara

2014-01-01

Severe combined immunodeficiency due to adenosine-deaminase defect (ADA-SCID) is usually deadly in childhood because of severe recurrent infections. When clinical diagnosis is done, permanent damages due to infections or metabolite accumulation are often present. Gene therapy, bone marrow transplantation or enzyme replacement therapy may be effective if started early. The aim of this study was to set-up a robust method suitable for screening with a minimized preparation process and with inexpensive running costs, for diagnosing ADA-SCID by tandem mass spectrometry. ADA-SCID satisfies all the criteria for inclusion in a newborn screening program. We describe a protocol revised to incorporate adenosine and 2-deoxyadenosine testing into an expanded newborn screening program. We assessed the effectiveness of this approach testing dried blood spots from 4 genetically confirmed early-onset and 5 delayed-onset ADA-SCID patients. Reference values were established on 50,000 healthy newborns (deoxyadenosine <0.09μmol/L, adenosine <1.61μmol/L). We also developed a second tier test to distinguish true positives from false positives and improve the positive predictive value of an initial abnormal result. In the first 18 months, the pilot project has identified a newborn with a genetically confirmed defect in adenosine deaminase (ADA) gene. The results show that the method having great simplicity, low cost and low process preparations can be fully applicable to a mass screening program. Copyright © 2013 Elsevier B.V. All rights reserved.

Steroidogenic versus Metabolic Programming of Reproductive Neuroendocrine, Ovarian and Metabolic Dysfunctions.

PubMed

Cardoso, Rodolfo C; Puttabyatappa, Muraly; Padmanabhan, Vasantha

2015-01-01

The susceptibility of the reproductive system to early exposure to steroid hormones has become a major concern in our modern societies. Human fetuses are at risk of abnormal programming via exposure to endocrine disrupting chemicals, inadvertent use of contraceptive pills during pregnancy, as well as from excess exposure to steroids due to disease states. Animal models provide an unparalleled resource to understand the developmental origin of diseases. In female sheep, prenatal exposure to testosterone excess results in an array of adult reproductive disorders that recapitulate those seen in women with polycystic ovary syndrome (PCOS), including disrupted neuroendocrine feedback mechanisms, increased pituitary sensitivity to gonadotropin-releasing hormone, luteinizing hormone excess, functional hyperandrogenism, and multifollicular ovarian morphology culminating in early reproductive failure. Prenatal testosterone treatment also leads to fetal growth retardation, insulin resistance, and hypertension. Mounting evidence suggests that developmental exposure to an improper steroidal/metabolic environment may mediate the programming of adult disorders in prenatal testosterone-treated females, and these defects are maintained or amplified by the postnatal sex steroid and metabolic milieu. This review addresses the steroidal and metabolic contributions to the development and maintenance of the PCOS phenotype in the prenatal testosterone-treated sheep model, including the effects of prenatal and postnatal treatment with an androgen antagonist or insulin sensitizer as potential strategies to prevent/ameliorate these dysfunctions. Insights obtained from these intervention strategies on the mechanisms underlying these defects are likely to have translational relevance to human PCOS. © 2015 S. Karger AG, Basel.

Plasma folate levels in early to mid pregnancy after a nation-wide folic acid supplementation program in areas with high and low prevalence of neural tube defects in China.

PubMed

Liu, Jufen; Gao, Lili; Zhang, Yali; Jin, Lei; Li, Zhiwen; Zhang, Le; Meng, Qinqin; Ye, Rongwei; Wang, Linlin; Ren, Aiguo

2015-06-01

Folic acid supplementation is recommended for all women of child-bearing age to prevent neural tube defects (NTDs). A nation-wide folic acid supplementation program was implemented in rural areas of China since 2009; however, changes in plasma folate levels in pregnant women were unknown. A cross-sectional survey was conducted in 2011 to 2012, with 1736 pregnant women enrolled, and results were compared with a previous survey in 2002 to 2004. A microbiological method was used to determine plasma folate levels. Preprogram and postprogram median plasma folate concentrations were compared while stratified by prevalence of NTDs and residence. In the high NTD prevalence population, plasma folate concentration increased to 33.4 (18.7, 58.4) nmol/L in the postprogram sample, which is 2.9 times of the preprogram. In the low NTD prevalence population, plasma folate increased to 67.9 (44.5, 101.9) nmol/L, which is 1.9 times of the preprogram. Gaps remained in plasma folate levels with respect to prevalence of NTDs and residence. Folic acid supplementation has a strong impact on plasma folate concentrations. Earlier supplementation (before the last menstrual period), increased supplementation frequency and more total days of supplementation were associated with a higher plasma folate concentration as demonstrated in both the high- and low-prevalence populations. Plasma folate levels among pregnant Chinese women increased dramatically after the nation-wide folic acid supplementation program in both rural and urban areas, and in populations of high and low NTD prevalence. The nation-wide program should have a component to ensure that supplementation begins before pregnancy. © 2015 Wiley Periodicals, Inc.

Developmental Programming: Prenatal and Postnatal Androgen Antagonist and Insulin Sensitizer Interventions Prevent Advancement of Puberty and Improve LH Surge Dynamics in Prenatal Testosterone-Treated Sheep

PubMed Central

Veiga-Lopez, Almudena; Herkimer, Carol; Abi Salloum, Bachir; Moeller, Jacob; Beckett, Evan; Sreedharan, Rohit

2015-01-01

Prenatal T excess induces maternal hyperinsulinemia, early puberty, and reproductive/metabolic defects in the female similar to those seen in women with polycystic ovary syndrome. This study addressed the organizational/activational role of androgens and insulin in programming pubertal advancement and periovulatory LH surge defects. Treatment groups included the following: 1) control; 2) prenatal T; 3) prenatal T plus prenatal androgen antagonist, flutamide; 4) prenatal T plus prenatal insulin sensitizer, rosiglitazone; 5) prenatal T and postnatal flutamide; 6) prenatal T and postnatal rosiglitazone; and 7) prenatal T and postnatal metformin. Prenatal treatments spanned 30–90 days of gestation and postnatal treatments began at approximately 8 weeks of age and continued throughout. Blood samples were taken twice weekly, beginning at approximately 12 weeks of age to time puberty. Two-hour samples after the synchronization with prostaglandin F2α were taken for 120 hours to characterize LH surge dynamics at 7 and 19 months of age. Prenatal T females entered puberty earlier than controls, and all interventions prevented this advancement. Prenatal T reduced the percentage of animals having LH surge, and females that presented LH surge exhibited delayed timing and dampened amplitude of the LH surge. Prenatal androgen antagonist, but not other interventions, restored LH surges without normalizing the timing of the surge. Normalization of pubertal timing with prenatal/postnatal androgen antagonist and insulin sensitizer interventions suggests that pubertal advancement is programmed by androgenic actions of T involving insulin as a mediary. Restoration of LH surges by cotreatment with androgen antagonist supports androgenic programming at the organizational level. PMID:25919188

Developmental Programming: Prenatal and Postnatal Androgen Antagonist and Insulin Sensitizer Interventions Prevent Advancement of Puberty and Improve LH Surge Dynamics in Prenatal Testosterone-Treated Sheep.

PubMed

Padmanabhan, Vasantha; Veiga-Lopez, Almudena; Herkimer, Carol; Abi Salloum, Bachir; Moeller, Jacob; Beckett, Evan; Sreedharan, Rohit

2015-07-01

Prenatal T excess induces maternal hyperinsulinemia, early puberty, and reproductive/metabolic defects in the female similar to those seen in women with polycystic ovary syndrome. This study addressed the organizational/activational role of androgens and insulin in programming pubertal advancement and periovulatory LH surge defects. Treatment groups included the following: 1) control; 2) prenatal T; 3) prenatal T plus prenatal androgen antagonist, flutamide; 4) prenatal T plus prenatal insulin sensitizer, rosiglitazone; 5) prenatal T and postnatal flutamide; 6) prenatal T and postnatal rosiglitazone; and 7) prenatal T and postnatal metformin. Prenatal treatments spanned 30-90 days of gestation and postnatal treatments began at approximately 8 weeks of age and continued throughout. Blood samples were taken twice weekly, beginning at approximately 12 weeks of age to time puberty. Two-hour samples after the synchronization with prostaglandin F2α were taken for 120 hours to characterize LH surge dynamics at 7 and 19 months of age. Prenatal T females entered puberty earlier than controls, and all interventions prevented this advancement. Prenatal T reduced the percentage of animals having LH surge, and females that presented LH surge exhibited delayed timing and dampened amplitude of the LH surge. Prenatal androgen antagonist, but not other interventions, restored LH surges without normalizing the timing of the surge. Normalization of pubertal timing with prenatal/postnatal androgen antagonist and insulin sensitizer interventions suggests that pubertal advancement is programmed by androgenic actions of T involving insulin as a mediary. Restoration of LH surges by cotreatment with androgen antagonist supports androgenic programming at the organizational level.

A New Tool for Quality Control

NASA Technical Reports Server (NTRS)

1988-01-01

Diffracto, Ltd. is now offering a new product inspection system that allows detection of minute flaws previously difficult or impossible to observe. Called D-Sight, it represents a revolutionary technique for inspection of flat or curved surfaces to find such imperfections as dings, dents and waviness. System amplifies defects, making them highly visible to simplify decision making as to corrective measures or to identify areas that need further study. CVA 3000 employs a camera, high intensity lamps and a special reflective screen to produce a D- Sight image of light reflected from a surface. Image is captured and stored in a computerized vision system then analyzed by a computer program. A live image of surface is projected onto a video display and compared with a stored master image to identify imperfections. Localized defects measuring less than 1/1000 of an inch are readily detected.

49 CFR Appendix A to Part 238 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2014 CFR

2014-10-01

....15Movement of power brake defects: (b) Improper movement from Class I or IA brake test 5,000 7,500 (c... required design features 5,000 7,500 (e) Failure to comply with hardware and software safety program 5,000... test previously used equipment 7,500 11,000 (b)(1) Failure to develop plan 7,500 11,000 (b)(2) Failure...

49 CFR Appendix A to Part 238 - Schedule of Civil Penalties 1

Code of Federal Regulations, 2010 CFR

2010-10-01

....15Movement of power brake defects: (b) Improper movement from Class I or IA brake test 5,000 7,500 (c... required design features 5,000 7,500 (e) Failure to comply with hardware and software safety program 5,000... test previously used equipment 7,500 11,000 (b)(1) Failure to develop plan 7,500 11,000 (b)(2) Failure...

Data bank for short-length red oak lumber

Treesearch

Janice K. Wiedenbeck; Charles J. Gatchell; Elizabeth S. Walker

1994-01-01

This data bank for short-length lumber (less than 8 feet long) contains information on board outlines and defect size and quality for 426 414-inch-thick red oak boards. The Selects, 1 Common, 2A Common, and 3A Common grades are represented in the data bank. The data bank provides the kind of detailed lumber description that is required as input by computer programs...

Parts, Materials, and Processes Control Program for Expendable Launch Vehicles

DTIC Science & Technology

2015-07-31

burn-in, electrical tests (DWV, room and hot IR, partial discharge when in corona region); perform DPA with SEM/EDX analysis of dielectric...life test; x-ray and vicinal illumination inspection; electrical tests (DWV, room and hot IR, partial discharge when in corona region) Termination...defects; proper voltage derating. Partial discharge testing, corona inception testing up to 60% of rated voltage; CSAM screening; voltage burn

Development of a computer method for predicting lumber cutting yields.

Treesearch

Daniel E. Dunmire; George H. Englerth

1967-01-01

A system of locating defects in a board by intersecting coordinate points was developed and a computer program devised that used these points to locate all possible clear areas in the board. The computer determined the yields by placing any given size or sizes of cuttings in these clear areas, and furthermore stated the type, location, and number of saw cuts. The...

A Machine Vision System for Automatically Grading Hardwood Lumber - (Industrial Metrology)

Treesearch

Richard W. Conners; Tai-Hoon Cho; Chong T. Ng; Thomas T. Drayer; Philip A. Araman; Robert L. Brisbon

1992-01-01

Any automatic system for grading hardwood lumber can conceptually be divided into two components. One of these is a machine vision system for locating and identifying grading defects. The other is an automatic grading program that accepts as input the output of the machine vision system and, based on these data, determines the grade of a board. The progress that has...

Temperature Distribution Within a Defect-Free Silicon Carbide Diode Predicted by a Computational Model

NASA Technical Reports Server (NTRS)

Kuczmarski, Maria A.; Neudeck, Philip G.

2000-01-01

Most solid-state electronic devices diodes, transistors, and integrated circuits are based on silicon. Although this material works well for many applications, its properties limit its ability to function under extreme high-temperature or high-power operating conditions. Silicon carbide (SiC), with its desirable physical properties, could someday replace silicon for these types of applications. A major roadblock to realizing this potential is the quality of SiC material that can currently be produced. Semiconductors require very uniform, high-quality material, and commercially available SiC tends to suffer from defects in the crystalline structure that have largely been eliminated in silicon. In some power circuits, these defects can focus energy into an extremely small area, leading to overheating that can damage the device. In an effort to better understand the way that these defects affect the electrical performance and reliability of an SiC device in a power circuit, the NASA Glenn Research Center at Lewis Field began an in-house three-dimensional computational modeling effort. The goal is to predict the temperature distributions within a SiC diode structure subjected to the various transient overvoltage breakdown stresses that occur in power management circuits. A commercial computational fluid dynamics computer program (FLUENT-Fluent, Inc., Lebanon, New Hampshire) was used to build a model of a defect-free SiC diode and generate a computational mesh. A typical breakdown power density was applied over 0.5 msec in a heated layer at the junction between the p-type SiC and n-type SiC, and the temperature distribution throughout the diode was then calculated. The peak temperature extracted from the computational model agreed well (within 6 percent) with previous first-order calculations of the maximum expected temperature at the end of the breakdown pulse. This level of agreement is excellent for a model of this type and indicates that three-dimensional computational modeling can provide useful predictions for this class of problem. The model is now being extended to include the effects of crystal defects. The model will provide unique insights into how high the temperature rises in the vicinity of the defects in a diode at various power densities and pulse durations. This information also will help researchers in understanding and designing SiC devices for safe and reliable operation in high-power circuits.

Single-Cell Resolution of Temporal Gene Expression during Heart Development.

PubMed

DeLaughter, Daniel M; Bick, Alexander G; Wakimoto, Hiroko; McKean, David; Gorham, Joshua M; Kathiriya, Irfan S; Hinson, John T; Homsy, Jason; Gray, Jesse; Pu, William; Bruneau, Benoit G; Seidman, J G; Seidman, Christine E

2016-11-21

Activation of complex molecular programs in specific cell lineages governs mammalian heart development, from a primordial linear tube to a four-chamber organ. To characterize lineage-specific, spatiotemporal developmental programs, we performed single-cell RNA sequencing of >1,200 murine cells isolated at seven time points spanning embryonic day 9.5 (primordial heart tube) to postnatal day 21 (mature heart). Using unbiased transcriptional data, we classified cardiomyocytes, endothelial cells, and fibroblast-enriched cells, thus identifying markers for temporal and chamber-specific developmental programs. By harnessing these datasets, we defined developmental ages of human and mouse pluripotent stem-cell-derived cardiomyocytes and characterized lineage-specific maturation defects in hearts of mice with heterozygous mutations in Nkx2.5 that cause human heart malformations. This spatiotemporal transcriptome analysis of heart development reveals lineage-specific gene programs underlying normal cardiac development and congenital heart disease. Copyright © 2016 Elsevier Inc. All rights reserved.

At the Edge of Translation – Materials to Program Cells for Directed Differentiation

PubMed Central

Arany, Praveen R; Mooney, David J

2010-01-01

The rapid advancement in basic biology knowledge, especially in the stem cell field, has created new opportunities to develop biomaterials capable of orchestrating the behavior of transplanted and host cells. Based on our current understanding of cellular differentiation, a conceptual framework for the use of materials to program cells in situ is presented, namely a domino versus a switchboard model, to highlight the use of single versus multiple cues in a controlled manner to modulate biological processes. Further, specific design principles of material systems to present soluble and insoluble cues that are capable of recruiting, programming and deploying host cells for various applications are presented. The evolution of biomaterials from simple inert substances used to fill defects, to the recent development of sophisticated material systems capable of programming cells in situ is providing a platform to translate our understanding of basic biological mechanisms to clinical care. PMID:20860763

Modeling of rolling element bearing mechanics. Computer program user's manual

NASA Technical Reports Server (NTRS)

Greenhill, Lyn M.; Merchant, David H.

1994-01-01

This report provides the user's manual for the Rolling Element Bearing Analysis System (REBANS) analysis code which determines the quasistatic response to external loads or displacement of three types of high-speed rolling element bearings: angular contact ball bearings, duplex angular contact ball bearings, and cylindrical roller bearings. The model includes the defects of bearing ring and support structure flexibility. It is comprised of two main programs: the Preprocessor for Bearing Analysis (PREBAN) which creates the input files for the main analysis program, and Flexibility Enhanced Rolling Element Bearing Analysis (FEREBA), the main analysis program. This report addresses input instructions for and features of the computer codes. A companion report addresses the theoretical basis for the computer codes. REBANS extends the capabilities of the SHABERTH (Shaft and Bearing Thermal Analysis) code to include race and housing flexibility, including such effects as dead band and preload springs.

[Tailored cranioplasty using CAD-CAM technology].

PubMed

Vitanovics, Dusán; Major, Ottó; Lovas, László; Banczerowski, Péter

2014-11-30

The majority of cranial defects are results of surgical intervention. The defect must be covered within resonable period of time usually after 4-6 week given the fact that the replacement of bone improve the brain circulation. Number of surgical techniques and materials are available to perform cranioplasty. Due to favorable properties we chosed ultra high molecular weight polyethylene as material. In this paper the authors show a procedure which allows tailored artificial bone replacement using state of art medical and engineering techniques. between 2004 and 2012, 19 patients were operated on cranial bone defect and a total of 22 3D custom-designed implants were implanted. The average age of patients was 35.4 years. In 12 patients we performed primary cranioplasty, while seven patients had the replacement at least once. Later the implants had to be removed due to infection or other causes (bone necrosis, fracture). All patients had native and bone-windowed 1 mm resolution CT. The 3D design was made using the original CT images and with design program. Computer controlled lathe was used to prepare a precise-fitting model. During surgery, the defect was exposed and the implant was fixed to normal bone using mini titanium plates and screws. All of our patients had control CT at 3, 6 and 12 months after surgery and at the same time neurological examination. Twenty-one polyethylene and one titanium implants were inserted. The average follow-up of the patients was 21.5 months, ranged from two to 96 months. We follow 12 patients (63.15%) more than one year. No intraoperative implant modifications had to be made. Each of the 22 implant exactly matched the bone defect proved by CT scan. No one of our patients reported aesthetic problems and we did not notice any kind of aesthetic complication. We had short term complication in three cases due to cranioplasty, subdural, epidural haemorrhage and skin defect. Polyethylene is in all respects suitable for primary and secondary cranioplasty. Combined with 3D CAD- CAM method excellent aesthetic and functional result was achieved. In our study no case of infection occured. Proper preoperative preparation is important.

Analysis of a link of embrittlement mechanisms and neutron flux effect as applied to reactor pressure vessel materials of WWER

NASA Astrophysics Data System (ADS)

Margolin, B. Z.; Yurchenko, E. V.; Morozov, A. M.; Pirogova, N. E.; Brumovsky, M.

2013-03-01

The effect of neutron flux on embrittlement of WWER RPV materials is analyzed for cases when different radiation defects prevail. Data bases on the ductile-brittle transition temperature shifts obtained in the surveillance specimens programs and the research programs are used. The material embrittlement mechanisms for which the flux effect is practically absent and for which the flux effect is remarkable are determined. For case when the phosphorus segregation mechanism dominates the theoretical justification of the absence of the flux effect is performed on the basis of the theory of radiation-enhanced diffusion.

Repair, Evaluation, Maintenance, and Rehabilitation Research Program. Inspection of the Engineering Condition of Underwater Concrete Structures.

DTIC Science & Technology

1989-04-01

corrosion of rebar Spalling of concrete surface IIl Detect hidden and beginning Location of rebar damage Beginning corrosion of rebar ...honeycombs MD Moderate defects: spalling of concrete minor corrosion of exposed rebar rust stains along rebar with or without visible cracking softening of...velocity. . Replenishment of the attacking chemical hgents. h. Higher temperatures. i. Corrosion of reinforcing steel. 46. Note that concrete which

Test of the Center for Automated Processing of Hardwoods' Auto-Image Detection and Computer-Based Grading and Cutup System

Treesearch

Philip A. Araman; Janice K. Wiedenbeck

1995-01-01

Automated lumber grading and yield optimization using computer controlled saws will be plausible for hardwoods if and when lumber scanning systems can reliably identify all defects by type. Existing computer programs could then be used to grade the lumber, identify the best cut-up solution, and control the sawing machines. The potential value of a scanning grading...

Mining Program Source Code for Improving Software Quality

DTIC Science & Technology

2013-01-01

conduct static verification on the software application under analysis to detect defects around APIs. (a) Papers published in peer-reviewed journals...N/A for none) Enter List of papers submitted or published that acknowledge ARO support from the start of the project to the date of this printing...List the papers , including journal references, in the following categories: Received Paper 05/06/2013 21.00 Tao Xie, Suresh Thummalapenta, David Lo

Parts, Materials, and Processes Control Program for Expendable Launch Vehicles

DTIC Science & Technology

2015-05-21

CSAM, thermal shock, voltage burn-in, electrical tests (DWV, room and hot IR, partial discharge when in corona region); perform DPA with SEM/EDX...controls to eliminate dielectric defects; proper voltage derating. Partial discharge testing, corona inception testing up to 60% of rated voltage...voltage burn-in; DWV; room and hot IR; life test; partial discharge when in corona region B-7 Table B-5. Metallized Plastic Capacitors

Identifying Acquisition Patterns of Failure Using Systems Archetypes

DTIC Science & Technology

2008-04-02

OF PAGES 18 19a. NAME OF RESPONSIBLE PERSON a. REPORT unclassified b . ABSTRACT unclassified c. THIS PAGE unclassified Standard Form 298 (Rev...any but the smallest programs, complete path coverage for defect detection is impractical. Adapted from Pressman , R.S., Software Engineering: A...Firefighting” concept from “Past the Tipping Point” Fix S O B Problem Symptom R “Fixes That Fail” – Systems Archetype S Unintended Consequences S

Defense Logistics Agency Can Improve Its Product Quality Deficiency Report Processing

DTIC Science & Technology

2015-07-01

Contracts for M2 Machine Gun Spare Parts in Support of Operations in Southwest Asia,” January 11, 2010 Appendixes DODIG-2015-140 │ 29 Appendix B...personnel are adequately processing product quality deficiency reports and identifying the root cause for defective spare parts . This is the first...quality deficiency report program and prevents meaningful analysis of the primary causes of spare- part quality deficiencies. In addition, the

Environmental and High-Strain Rate effects on composites for engine applications

NASA Technical Reports Server (NTRS)

Chamis, C. C.; Smith, G. T.

1982-01-01

The Lewis Research Center is conducting a series of programs intended to investigate and develop the application of composite materials to structural components for turbojet engines. A significant part of that effort is directed to establishing resistance, defect growth, and strain rate characteristics of composite materials over the wide range of environmental and load conditions found in commercial turbojet engine operations. Both analytical and experimental efforts are involved.

The GTPase SPAG-1 orchestrates meiotic program by dictating meiotic resumption and cytoskeleton architecture in mouse oocytes

PubMed Central

Huang, Chunjie; Wu, Di; Khan, Faheem Ahmed; Jiao, Xiaofei; Guan, Kaifeng; Huo, Lijun

2016-01-01

In mammals, a finite population of oocytes is generated during embryogenesis, and proper oocyte meiotic divisions are crucial for fertility. Sperm-associated antigen 1 (SPAG-1) has been implicated in infertility and tumorigenesis; however, its relevance in cell cycle programs remains rudimentary. Here we explore a novel role of SPAG-1 during oocyte meiotic progression. SPAG-1 associated with meiotic spindles and its depletion severely compromised M-phase entry (germinal vesicle breakdown [GVBD]) and polar body extrusion. The GVBD defect observed was due to an increase in intraoocyte cAMP abundance and decrease in ATP production, as confirmed by the activation of AMP-dependent kinase (AMPK). SPAG-1 RNA interference (RNAi)–elicited defective spindle morphogenesis was evidenced by the dysfunction of γ-tubulin, which resulted from substantially reduced phosphorylation of MAPK and irregularly dispersed distribution of phospho-MAPK around spindles instead of concentration at spindle poles. Significantly, actin expression abruptly decreased and formation of cortical granule–free domains, actin caps, and contractile ring disrupted by SPAG-1 RNAi. In addition, the spindle assembly checkpoint remained functional upon SPAG-1 depletion. The findings broaden our knowledge of SPAG-1, showing that it exerts a role in oocyte meiotic execution via its involvement in AMPK and MAPK signaling pathways. PMID:27053660

Drosophila nemo is an essential gene involved in the regulation of programmed cell death.

PubMed

Mirkovic, Ivana; Charish, Kristi; Gorski, Sharon M; McKnight, Kristen; Verheyen, Esther M

2002-11-01

Nemo-like kinases define a novel family of serine/threonine kinases that are involved in integrating multiple signaling pathways. They are conserved regulators of Wnt/Wingless pathways, which may coordinate Wnt with TGFbeta-mediated signaling. Drosophila nemo was identified through its involvement in epithelial planar polarity, a process regulated by a non-canonical Wnt pathway. We have previously found that ectopic expression of Nemo using the Gal4-UAS system resulted in embryonic lethality associated with defects in patterning and head development. In this study we present our analyses of the phenotypes of germline clone-derived embryos. We observe lethality associated with head defects and reduction of programmed cell death and conclude that nmo is an essential gene. We also present data showing that nmo is involved in regulating apoptosis during eye development, based on both loss of function phenotypes and on genetic interactions with the pro-apoptotic gene reaper. Finally, we present genetic data from the adult wing that suggest the activity of ectopically expressed Nemo can be modulated by Jun N-terminal kinase (JNK) signaling. Such an observation supports the model that there is cross-talk between Wnt, TGFbeta and JNK signaling at multiple stages of development. Copyright 2002 Elsevier Science Ireland Ltd.

In-camera video-stream processing for bandwidth reduction in web inspection

NASA Astrophysics Data System (ADS)

Jullien, Graham A.; Li, QiuPing; Hajimowlana, S. Hossain; Morvay, J.; Conflitti, D.; Roberts, James W.; Doody, Brian C.

1996-02-01

Automated machine vision systems are now widely used for industrial inspection tasks where video-stream data information is taken in by the camera and then sent out to the inspection system for future processing. In this paper we describe a prototype system for on-line programming of arbitrary real-time video data stream bandwidth reduction algorithms; the output of the camera only contains information that has to be further processed by a host computer. The processing system is built into a DALSA CCD camera and uses a microcontroller interface to download bit-stream data to a XILINXTM FPGA. The FPGA is directly connected to the video data-stream and outputs data to a low bandwidth output bus. The camera communicates to a host computer via an RS-232 link to the microcontroller. Static memory is used to both generate a FIFO interface for buffering defect burst data, and for off-line examination of defect detection data. In addition to providing arbitrary FPGA architectures, the internal program of the microcontroller can also be changed via the host computer and a ROM monitor. This paper describes a prototype system board, mounted inside a DALSA camera, and discusses some of the algorithms currently being implemented for web inspection applications.

Kex1 protease is involved in yeast cell death induced by defective N-glycosylation, acetic acid, and chronological aging.

PubMed

Hauptmann, Peter; Lehle, Ludwig

2008-07-04

N-glycosylation in the endoplasmic reticulum is an essential protein modification and highly conserved in evolution from yeast to humans. The key step of this pathway is the transfer of the lipid-linked core oligosaccharide to the nascent polypeptide chain, catalyzed by the oligosaccharyltransferase complex. Temperature-sensitive oligosaccharyltransferase mutants of Saccharomyces cerevisiae at the restrictive temperature, such as wbp1-1, as well as wild-type cells in the presence of the N-glycosylation inhibitor tunicamycin display typical apoptotic phenotypes like nuclear condensation, DNA fragmentation, phosphatidylserine translocation, caspase-like activity, and reactive oxygen species accumulation. Since deletion of the yeast metacaspase YCA1 did not abrogate this death pathway, we postulated a different proteolytic process to be responsible. Here, we show that Kex1 protease is involved in the programmed cell death caused by defective N-glycosylation. Its disruption decreases caspase-like activity, production of reactive oxygen species, and fragmentation of mitochondria and, conversely, improves growth and survival of cells. Moreover, we demonstrate that Kex1 contributes also to the active cell death program induced by acetic acid stress or during chronological aging, suggesting that Kex1 plays a more general role in cellular suicide of yeast.

Genes Important for Schizosaccharomyces pombe Meiosis Identified Through a Functional Genomics Screen

PubMed Central

Blyth, Julie; Makrantoni, Vasso; Barton, Rachael E.; Spanos, Christos; Rappsilber, Juri; Marston, Adele L.

2018-01-01

Meiosis is a specialized cell division that generates gametes, such as eggs and sperm. Errors in meiosis result in miscarriages and are the leading cause of birth defects; however, the molecular origins of these defects remain unknown. Studies in model organisms are beginning to identify the genes and pathways important for meiosis, but the parts list is still poorly defined. Here we present a comprehensive catalog of genes important for meiosis in the fission yeast, Schizosaccharomyces pombe. Our genome-wide functional screen surveyed all nonessential genes for roles in chromosome segregation and spore formation. Novel genes important at distinct stages of the meiotic chromosome segregation and differentiation program were identified. Preliminary characterization implicated three of these genes in centrosome/spindle pole body, centromere, and cohesion function. Our findings represent a near-complete parts list of genes important for meiosis in fission yeast, providing a valuable resource to advance our molecular understanding of meiosis. PMID:29259000

The role of defects in the electrical properties of NbO2thin film vertical devices

NASA Astrophysics Data System (ADS)

Joshi, Toyanath; Borisov, Pavel; Lederman, David

Epitaxial NbO2 thin films were grown on Si:GaN layers deposited on Al2O3 substrates using pulsed laser deposition. Pulsed current-voltage (IV) curves and self-sustained current oscillations were measured across a 31 nm NbO2 film and compared with a similar device made from polycrystalline NbO2 film grown on TiN-coated SiO2/Si substrate. Crystal quality of the as grown films was determined from x-ray diffractometric, x-ray photoelectron spectroscopy and atomic force microscopy data. The epitaxial film device was found to be more stable than the defect-rich polycrystalline sample in terms of current switching and oscillation behaviors. This work was supported in part by FAME, one of six centers of STARnet, a Semiconductor Research Corporation program sponsored by MARCO and DARPA (Contract 2013-MA-2382), and the WVU Shared Research Facilities.

Age-dependent epigenetic control of differentiation inhibitors is critical for remyelination efficiency

PubMed Central

Shen, Siming; Sandoval, Juan; Swiss, Victoria A; Li, Jiadong; Dupree, Jeff; Franklin, Robin J M; Casaccia-Bonnefil, Patrizia

2009-01-01

The efficiency of remyelination decreases with age, but the molecular mechanisms responsible for this decline remain only partially understood. In this study, we show that remyelination is regulated by age-dependent epigenetic control of gene expression. In demyelinated young brains, new myelin synthesis is preceded by downregulation of oligodendrocyte differentiation inhibitors and neural stem cell markers, and this is associated with recruitment of histone deacetylases (HDACs) to promoter regions. In demyelinated old brains, HDAC recruitment is inefficient, and this allows the accumulation of transcriptional inhibitors and prevents the subsequent surge in myelin gene expression. Defective remyelination can be recapitulated in vivo in mice receiving systemic administration of pharmacological HDAC inhibitors during cuprizone treatment and is consistent with in vitro results showing defective differentiation of oligodendrocyte progenitors after silencing specific HDAC isoforms. Thus, we suggest that inefficient epigenetic modulation of the oligodendrocyte differentiation program contributes to the age-dependent decline in remyelination efficiency. PMID:19160500

Correlation Between Hot Spots and 3-d Defect Structure in Single and Polycrystalline High-explosive Materials

NASA Astrophysics Data System (ADS)

Hawkins, Cameron; Tschuaner, Oliver; Fussell, Zachary; Smith, Jesse

2017-06-01

A novel approach that spatially identifies inhomogeneities from microscale (defects, con-formational disorder) to mesoscale (voids, inclusions) is developed using synchrotron x-ray methods: tomography, Lang topography, and micro-diffraction mapping. These techniques pro-vide a non-destructive method for characterization of mm-sized samples prior to shock experiments. These characterization maps can be used to correlate continuum level measurements in shock compression experiments to the mesoscale and microscale structure. Specifically examined is a sample of C4. We show extensive conformational disorder in gamma-RDX, which is the main component. Further, we observe that the minor HMX-component in C4 contains at least two different phases: alpha- and beta-HMX. This work supported by National Security Technologies, LLC, under Contract No. DE-AC52-06NA25946 with the U.S. Department of Energy and by the Site-Directed Research and Development Program. DOE/NV/25946-3071.

Norrin/Frizzled4 signaling in retinal vascular development and blood brain barrier plasticity.

PubMed

Wang, Yanshu; Rattner, Amir; Zhou, Yulian; Williams, John; Smallwood, Philip M; Nathans, Jeremy

2012-12-07

Norrin/Frizzled4 (Fz4) signaling activates the canonical Wnt pathway to control retinal vascular development. Using genetically engineered mice, we show that precocious Norrin production leads to premature retinal vascular invasion and delayed Norrin production leads to characteristic defects in intraretinal vascular architecture. In genetic mosaics, wild-type endothelial cells (ECs) instruct neighboring Fz4(-/-) ECs to produce an architecturally normal mosaic vasculature, a cell nonautonomous effect. However, over the ensuing weeks, Fz4(-/-) ECs are selectively eliminated from the mosaic vasculature, implying the existence of a quality control program that targets defective ECs. In the adult retina and cerebellum, gain or loss of Norrin/Fz4 signaling results in a cell-autonomous gain or loss, respectively, of blood retina barrier and blood brain barrier function, indicating an ongoing requirement for Frizzled signaling in barrier maintenance and substantial plasticity in mature CNS vascular structure. Copyright © 2012 Elsevier Inc. All rights reserved.

Experimental validation of ultrasonic NDE simulation software

NASA Astrophysics Data System (ADS)

Dib, Gerges; Larche, Michael; Diaz, Aaron A.; Crawford, Susan L.; Prowant, Matthew S.; Anderson, Michael T.

2016-02-01

Computer modeling and simulation is becoming an essential tool for transducer design and insight into ultrasonic nondestructive evaluation (UT-NDE). As the popularity of simulation tools for UT-NDE increases, it becomes important to assess their reliability to model acoustic responses from defects in operating components and provide information that is consistent with in-field inspection data. This includes information about the detectability of different defect types for a given UT probe. Recently, a cooperative program between the Electrical Power Research Institute and the U.S. Nuclear Regulatory Commission was established to validate numerical modeling software commonly used for simulating UT-NDE of nuclear power plant components. In the first phase of this cooperative, extensive experimental UT measurements were conducted on machined notches with varying depth, length, and orientation in stainless steel plates. Then, the notches were modeled in CIVA, a semi-analytical NDE simulation platform developed by the French Commissariat a l'Energie Atomique, and their responses compared with the experimental measurements. Discrepancies between experimental and simulation results are due to either improper inputs to the simulation model, or to incorrect approximations and assumptions in the numerical models. To address the former, a variation study was conducted on the different parameters that are required as inputs for the model, specifically the specimen and transducer properties. Then, the ability of simulations to give accurate predictions regarding the detectability of the different defects was demonstrated. This includes the results in terms of the variations in defect amplitude indications, and the ratios between tip diffracted and specular signal amplitudes.

Effects of surface imperfections on the binding of CH 3OH and H 2O on FeS 2(100): using adsorbed Xe as a probe of mineral surface structure

NASA Astrophysics Data System (ADS)

Guevremont, J. M.; Strongin, D. R.; Schoonen, M. A. A.

1997-11-01

Studies are presented that investigate the adsorption and binding of CH 3OH and H 2O on the atomically clean (100) crystallographic plane of pyrite, FeS 2. Temperature programmed desorption suggests that both reactants adsorb molecularly at 90 K and desorb thermally between 170 and 400 K depending on the surface coverage. Photoemission of adsorbed xenon (PAX) suggests that the surface of pyrite is heterogeneous and contains a significant fraction of defect sites that are believed to be, at least in part, anion vacancy or sulfur-deficient sites. An upper limit of 0.2 is proposed for the fraction of surface sites that are defects on FeS 2(100). PAX indicates that these defect sites at low adsorbate coverage serve as the exclusive binding sites for H 2O and CH 3OH adsorbate. We speculate, on the basis of our ability to interpret PAX data for pyrite, that PAX may be of use for understanding the effect of short range order on adsorbate binding on other complex mineral surfaces. On the basis of high resolution electron energy loss spectroscopy, it is found that some dissociation of the adsorbate occurs on the pyrite. Vibrational data obtained with this technique suggests that FeO species result from the adsorbate decomposition. After saturation of the defect sites, further molecular adsorption is accommodated on the less reactive surface that we postulate is largely disulfide, the characteristic structural group of pyrite.

Modulation of ferroelectricity and resistance switching in SrTiO3 films

NASA Astrophysics Data System (ADS)

Yang, Fang; Wang, Weihua; Guo, Jiandong

SrTiO3 has remarkable dielectric property; it also exhibits ferroelectricity in thin films with strain or defects. It is expected that modulation of its ferroelectricity and electricity is potential in oxide electronics. The nonstoichiometry SrTiO3 thin films with different cation concentrations were prepared on Si (001) substrates. Piezoresponse force microscopy measurements show that those films with Sr deficiency display obvious ferroelectricity. The scanning transmission electron microscopy results show that there are interstitial Ti atoms in the unit cells. Polar defect pairs can be formed by the interstitial Ti atoms and Sr vacancies along [100] or [110] direction. Such antisitelike defects observed in SrTiO3 films are considered as the origin of the ferroelectricity. In this way, the SrTiO3 ferroelectricity can be modulated by control the concentration of the antisitelike defects via changing the cation concentration. Further, [(SrTiO3)3 /(LaTiO3)2 ]3 superlattices have been prepared on 0.67[Pb(Mg1/3Nb2/3) O3]-0.33[PbTiO3] (PMN-PT) substrate. The superlattices show resistance switching under the ferroelectric polarization of the PMN-PT substrate. The on/off ratio of the interfacial resistance is about 20% 25%. This can be applied in oxide electronics in potential. This work is supported by Chinese MOST (Grant No. 2014CB921001), Chinese NSFC (Grant No. 11404381 & Grant No. 11225422) and the Strategic Priority Research Program (B) of the Chinese Academy of Sciences (Grant No. XDB07030100).

A combined experimental and theoretical study on ethanol conversion to propylene over Y/ZrO2 catalyst

NASA Astrophysics Data System (ADS)

Wang, Fangfang; Xia, Wei; Mu, Xichuan; Chen, Kun; Si, Huimin; Li, Zhihao

2018-05-01

ZrO2-based catalysts doped with Y were prepared by co-precipitation method. The effect of yttrium modification on the selective conversion of bio-ethanol to propylene over ZrO2 catalysts was investigated. The physical and chemical properties of the catalysts were characterized by N2 adsorption-desorption method, temperature programmed desorption and X-ray diffraction. The maximum yield of propylene reached 44.0% over 0.03Y/ZrO2 catalyst. A coordination of acid-base properties accounts for the remarkable improvement of reaction activities over Y-doped ZrO2 catalysts in this investigation. On the basis of calculation results, it can be concluded that significant charge transfer occurs as a result of introduction of Y or O-vacancy. The adsorption of ethanol and propylene on perfect t-ZrO2 (1 0 1), defect t-ZrO2 (1 0 1) and Y/ZrO2 (1 0 1) surfaces were investigated with density functional theory (DFT). The adsorption for ethanol on Y/ZrO2 (1 0 1) and defect t-ZrO2 (1 0 1) surfaces are more stable than that on perfect t-ZrO2 (1 0 1). On the defect t-ZrO2 (1 0 1) surface, ethanol dominantly absorbs at the O-vacancy site, indicating that O-vacancy becomes the favorable adsorption site. On the Y/ZrO2 (1 0 1) and defect t-ZrO2 (1 0 1) surfaces, the adsorption energy of propylene decreases, which makes propylene desorb quickly after formation.

Improving efficiency and reducing administrative burden through electronic communication.

PubMed

Cook, Katlyn E; Ludens, Gail M; Ghosh, Amit K; Mundell, William C; Fleming, Kevin C; Majka, Andrew J

2013-01-01

The InBox messaging system is an internal, electronic program used at Mayo Clinic, Rochester, MN, to facilitate the sending, receiving, and answering of patient-specific messages and alerts. A standardized InBox was implemented in the Division of General Internal Medicine to decrease the time physicians, physician assistants, and nurse practitioners (clinicians) spend on administrative tasks and to increase efficiency. Clinicians completed surveys and a preintervention InBox pilot test to determine inefficiencies related to administrative burdens and defects (message entry errors). Results were analyzed using Pareto diagrams, value stream mapping, and root cause analysis to prioritize administrative-burden inefficiencies to develop a new, standardized InBox. Clinicians and allied health staff were the target of this intervention and received standardized InBox training followed by a postintervention pilot test for clinicians. Sixteen of 28 individuals (57%) completed the preintervention survey. Twenty-eight clinicians participated in 2 separate 8-day pilot tests (before and after intervention) for the standardized InBox. The number of InBox defects was substantially reduced from 37 (Pilot 1) to 7 (Pilot 2). Frequent InBox defects decreased from 25% to 10%. More than half of clinicians believed the standardized InBox positively affected their work, and 100% of clinicians reported no negative affect on their work. This project demonstrated the successful implementation of the standardized InBox messaging system. Initial assessments show substantial reduction of InBox entry defects and administrative tasks completed by clinicians. The findings of this project suggest increased clinician and allied health staff efficiency, satisfaction, improved clinician work-life balance, and decreased clinician burden caused by administrative tasks.

A novel process for introducing a new intraoperative program: a multidisciplinary paradigm for mitigating hazards and improving patient safety.

PubMed

Rodriguez-Paz, Jose M; Mark, Lynette J; Herzer, Kurt R; Michelson, James D; Grogan, Kelly L; Herman, Joseph; Hunt, David; Wardlow, Linda; Armour, Elwood P; Pronovost, Peter J

2009-01-01

Since the Institute of Medicine's report, To Err is Human, was published, numerous interventions have been designed and implemented to correct the defects that lead to medical errors and adverse events; however, most efforts were largely reactive. Safety, communication, team performance, and efficiency are areas of care that attract a great deal of attention, especially regarding the introduction of new technologies, techniques, and procedures. We describe a multidisciplinary process that was implemented at our hospital to identify and mitigate hazards before the introduction of a new technique: high-dose-rate intraoperative radiation therapy, (HDR-IORT). A multidisciplinary team of surgeons, anesthesiologists, radiation oncologists, physicists, nurses, hospital risk managers, and equipment specialists used a structured process that included in situ clinical simulation to uncover concerns among care providers and to prospectively identify and mitigate defects for patients who would undergo surgery using the HDR-IORT technique. We identified and corrected 20 defects in the simulated patient care process before application to actual patients. Subsequently, eight patients underwent surgery using the HDR-IORT technique with no recurrence of simulation-identified or unanticipated defects. Multiple benefits were derived from the use of this systematic process to introduce the HDR-IORT technique; namely, the safety and efficiency of care for this select patient population was optimized, and this process mitigated harmful or adverse events before the inclusion of actual patients. Further work is needed, but the process outlined in this paper can be universally applied to the introduction of any new technologies, treatments, or procedures.

Maternal eNOS deficiency determines a fatty liver phenotype of the offspring in a sex dependent manner

PubMed Central

Hocher, Berthold; Haumann, Hannah; Rahnenführer, Jan; Reichetzeder, Christoph; Kalk, Philipp; Pfab, Thiemo; Tsuprykov, Oleg; Winter, Stefan; Hofmann, Ute; Li, Jian; Püschel, Gerhard P.; Lang, Florian; Schuppan, Detlef; Schwab, Matthias; Schaeffeler, Elke

2016-01-01

ABSTRACT Maternal environmental factors can impact on the phenotype of the offspring via the induction of epigenetic adaptive mechanisms. The advanced fetal programming hypothesis proposes that maternal genetic variants may influence the offspring's phenotype indirectly via epigenetic modification, despite the absence of a primary genetic defect. To test this hypothesis, heterozygous female eNOS knockout mice and wild type mice were bred with male wild type mice. We then assessed the impact of maternal eNOS deficiency on the liver phenotype of wild type offspring. Birth weight of male wild type offspring born to female heterozygous eNOS knockout mice was reduced compared to offspring of wild type mice. Moreover, the offspring displayed a sex specific liver phenotype, with an increased liver weight, due to steatosis. This was accompanied by sex specific differences in expression and DNA methylation of distinct genes. Liver global DNA methylation was significantly enhanced in both male and female offspring. Also, hepatic parameters of carbohydrate metabolism were reduced in male and female offspring. In addition, male mice displayed reductions in various amino acids in the liver. Maternal genetic alterations, such as partial deletion of the eNOS gene, can affect liver metabolism of wild type offspring without transmission of the intrinsic defect. This occurs in a sex specific way, with more detrimental effects in females. This finding demonstrates that a maternal genetic defect can epigenetically alter the phenotype of the offspring, without inheritance of the defect itself. Importantly, these acquired epigenetic phenotypic changes can persist into adulthood. PMID:27175980

A possible cranio-oro-facial phenotype in Cockayne syndrome

PubMed Central

2013-01-01

Background Cockayne Syndrome CS (Type A – CSA; or CS Type I OMIM #216400) (Type B – CSB; or CS Type II OMIM #133540) is a rare autosomal recessive neurological disease caused by defects in DNA repair characterized by progressive cachectic dwarfism, progressive intellectual disability with cerebral leukodystrophy, microcephaly, progressive pigmentary retinopathy, sensorineural deafness photosensitivity and possibly orofacial and dental anomalies. Methods We studied the cranio-oro-facial status of a group of 17 CS patients from 15 families participating in the National Hospital Program for Clinical Research (PHRC) 2005 « Clinical and molecular study of Cockayne syndrome ». All patients were examined by two investigators using the Diagnosing Dental Defects Database (D[4]/phenodent) record form. Results Various oro-facial and dental anomalies were found: retrognathia; micrognathia; high- arched narrow palate; tooth crowding; hypodontia (missing permanent lateral incisor, second premolars or molars), screwdriver shaped incisors, microdontia, radiculomegaly, and enamel hypoplasia. Eruption was usually normal. Dental caries was associated with enamel defects, a high sugar/carbohydrate soft food diet, poor oral hygiene and dry mouth. Cephalometric analysis revealed mid-face hypoplasia, a small retroposed mandible and hypo-development of the skull. Conclusion CS patients may have associated oro-dental features, some of which may be more frequent in CS children – some of them being described for the first time in this paper (agenesis of second permanent molars and radiculomegaly). The high susceptibility to rampant caries is related to a combination of factors as well as enamel developmental defects. Specific attention to these anomalies may contribute to diagnosis and help plan management. PMID:23311583

HYPERSAMP - HYPERGEOMETRIC ATTRIBUTE SAMPLING SYSTEM BASED ON RISK AND FRACTION DEFECTIVE

NASA Technical Reports Server (NTRS)

De, Salvo L. J.

1994-01-01

HYPERSAMP is a demonstration of an attribute sampling system developed to determine the minimum sample size required for any preselected value for consumer's risk and fraction of nonconforming. This statistical method can be used in place of MIL-STD-105E sampling plans when a minimum sample size is desirable, such as when tests are destructive or expensive. HYPERSAMP utilizes the Hypergeometric Distribution and can be used for any fraction nonconforming. The program employs an iterative technique that circumvents the obstacle presented by the factorial of a non-whole number. HYPERSAMP provides the required Hypergeometric sample size for any equivalent real number of nonconformances in the lot or batch under evaluation. Many currently used sampling systems, such as the MIL-STD-105E, utilize the Binomial or the Poisson equations as an estimate of the Hypergeometric when performing inspection by attributes. However, this is primarily because of the difficulty in calculation of the factorials required by the Hypergeometric. Sampling plans based on the Binomial or Poisson equations will result in the maximum sample size possible with the Hypergeometric. The difference in the sample sizes between the Poisson or Binomial and the Hypergeometric can be significant. For example, a lot size of 400 devices with an error rate of 1.0% and a confidence of 99% would require a sample size of 400 (all units would need to be inspected) for the Binomial sampling plan and only 273 for a Hypergeometric sampling plan. The Hypergeometric results in a savings of 127 units, a significant reduction in the required sample size. HYPERSAMP is a demonstration program and is limited to sampling plans with zero defectives in the sample (acceptance number of zero). Since it is only a demonstration program, the sample size determination is limited to sample sizes of 1500 or less. The Hypergeometric Attribute Sampling System demonstration code is a spreadsheet program written for IBM PC compatible computers running DOS and Lotus 1-2-3 or Quattro Pro. This program is distributed on a 5.25 inch 360K MS-DOS format diskette, and the program price includes documentation. This statistical method was developed in 1992.

The Legacy of Space Shuttle Flight Software

NASA Technical Reports Server (NTRS)

Hickey, Christopher J.; Loveall, James B.; Orr, James K.; Klausman, Andrew L.

2011-01-01

The initial goals of the Space Shuttle Program required that the avionics and software systems blaze new trails in advancing avionics system technology. Many of the requirements placed on avionics and software were accomplished for the first time on this program. Examples include comprehensive digital fly-by-wire technology, use of a digital databus for flight critical functions, fail operational/fail safe requirements, complex automated redundancy management, and the use of a high-order software language for flight software development. In order to meet the operational and safety goals of the program, the Space Shuttle software had to be extremely high quality, reliable, robust, reconfigurable and maintainable. To achieve this, the software development team evolved a software process focused on continuous process improvement and defect elimination that consistently produced highly predictable and top quality results, providing software managers the confidence needed to sign each Certificate of Flight Readiness (COFR). This process, which has been appraised at Capability Maturity Model (CMM)/Capability Maturity Model Integration (CMMI) Level 5, has resulted in one of the lowest software defect rates in the industry. This paper will present an overview of the evolution of the Primary Avionics Software System (PASS) project and processes over thirty years, an argument for strong statistical control of software processes with examples, an overview of the success story for identifying and driving out errors before flight, a case study of the few significant software issues and how they were either identified before flight or slipped through the process onto a flight vehicle, and identification of the valuable lessons learned over the life of the project.

Detection of Glaucoma and Its Association With Diabetic Retinopathy in a Diabetic Retinopathy Screening Program.

PubMed

Gangwani, Rita A; McGhee, Sarah M; Lai, Jimmy S M; Chan, Christina K W; Wong, David

2016-01-01

To determine the type of glaucoma in subjects with diabetes mellitus detected during a diabetic retinopathy screening program and to determine any association between diabetic retinopathy (DR) and glaucoma. This is a population-based prospective cross-sectional study, in which subjects with diabetes mellitus underwent screening for DR in a primary care outpatient clinic. Digital fundus photographs were taken and graded for presence/absence and severity of DR. During this grading, those fundus photographs showing increased cup-to-disc ratio (CDR) (≥0.6) were identified and these patients were referred to the specialist ophthalmology clinic for detailed examination. The presence of glaucoma was established based on CDR and abnormal visual field (VF) defects according to Hodapp-Parrish-Anderson's criteria. An elevation of intraocular pressure was not required for the diagnosis of glaucoma. The patients said to have definite glaucoma were those with vertical CDR>/=0.6, glaucomatous defects on VF examination, or retinal nerve fiber thinning if VF was unreliable. Of the 2182 subjects who underwent screening, 81 subjects (3.7%) had increased CDR and 40 subjects (1.8%) had confirmed glaucoma. Normal-tension variant of primary open-angle glaucoma was the most prevalent type (1.2%) We did not find any evidence that DR is a risk factor for glaucoma [odds ratio for DR vs. no DR=1.22 (95% confidence interval, 0.59-2.51)]. The overall prevalence of glaucoma in this diabetic population, based on finding increased cupping of optic disc in a teleretinal screening program was 1.8% (95% confidence interval, 1.0-3.0).

ZebraZoom: an automated program for high-throughput behavioral analysis and categorization

PubMed Central

Mirat, Olivier; Sternberg, Jenna R.; Severi, Kristen E.; Wyart, Claire

2013-01-01

The zebrafish larva stands out as an emergent model organism for translational studies involving gene or drug screening thanks to its size, genetics, and permeability. At the larval stage, locomotion occurs in short episodes punctuated by periods of rest. Although phenotyping behavior is a key component of large-scale screens, it has not yet been automated in this model system. We developed ZebraZoom, a program to automatically track larvae and identify maneuvers for many animals performing discrete movements. Our program detects each episodic movement and extracts large-scale statistics on motor patterns to produce a quantification of the locomotor repertoire. We used ZebraZoom to identify motor defects induced by a glycinergic receptor antagonist. The analysis of the blind mutant atoh7 revealed small locomotor defects associated with the mutation. Using multiclass supervised machine learning, ZebraZoom categorized all episodes of movement for each larva into one of three possible maneuvers: slow forward swim, routine turn, and escape. ZebraZoom reached 91% accuracy for categorization of stereotypical maneuvers that four independent experimenters unanimously identified. For all maneuvers in the data set, ZebraZoom agreed with four experimenters in 73.2–82.5% of cases. We modeled the series of maneuvers performed by larvae as Markov chains and observed that larvae often repeated the same maneuvers within a group. When analyzing subsequent maneuvers performed by different larvae, we found that larva–larva interactions occurred as series of escapes. Overall, ZebraZoom reached the level of precision found in manual analysis but accomplished tasks in a high-throughput format necessary for large screens. PMID:23781175

What do consistently high-performing in vitro fertilization programs in the U.S. do?

PubMed

Van Voorhis, Bradley J; Thomas, Mika; Surrey, Eric S; Sparks, Amy

2010-09-01

To identify common clinical and laboratory practices among consistently high-performing IVF programs. Questionnaire study of selected IVF programs. Academic and private practice IVF programs. Ten of 12 programs identified as having consistently high singleton delivery rates per cycle. None. Common clinical practices. Common clinical practices identified among these programs included testing all patients for ovarian reserve, endometrial defects, and hydrosalpinges; use of a mixed LH and FSH stimulation protocol with step-down dosing; and use of ultrasound guidance for ET. Common laboratory practices included selective use of intracytoplasmic sperm injection, group culture of embryos in microdrops, and use of blastocyst ET in selected cases. Common laboratory features included good air quality using filtration and heated stages for oocyte and embryo work. Although a number of factors were identified in this best-practices questionnaire, programs often differed in many aspects of care. However, high-performing programs cited experience of physicians, embryologists, and staff members as well as consistency of approach, attention to detail, and good communication as being vital to excellent outcomes. Copyright (c) 2010 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

[Transient congenital hypothyroidism due to biallelic defects of DUOX2 gene. Two clinical cases].

PubMed

Enacán, Rosa E; Masnata, María E; Belforte, Fiorella; Papendieck, Patricia; Olcese, María C; Siffo, Sofía; Gruñeiro-Papendieck, Laura; Targovnik, Héctor; Rivolta, Carina M; Chiesa, Ana E

2017-06-01

Congenital hypothyroidism affects 1:2000-3000 newborns detected by neonatal screening programs. Dual oxidases, DUOX1 and 2, generate hydrogen peroxide needed for the thyroid hormone synthesis. Hipotiroidismo congénito transitorio por defectos bialélicos del gen DUOX2. Dos casos clínicos Transient congenital hypothyroidism due to biallelic defects of DUOX2 gene. Two clinical cases Mutations in the DUOX2 gene have been described in transient and permanent congenital hypothyroidism. Two brothers with congenital hypothyroidism detected by neonatal screening with eutopic gland and elevated thyroglobulin are described. They were treated with levothyroxine until it could be suspended in both during childhood, assuming the picture as transient. Organification disorder was confirmed. Both patients were compounds heterozygous for a mutation in exon 9 of the paternal allele (c.1057_1058delTT, p.F353PfsX36 or p.F353fsX388) and in exon 11 of the maternal allele (c.1271T > G, p.Y425X) of DUOX2 gene. Our finding confirms that the magnitude of the defect of DUOX2 is not related to the number of inactivated alleles, suggesting compensatory mechanisms in the peroxide supply. Sociedad Argentina de Pediatría.

Bacillus subtilis Mutants with Knockouts of the Genes Encoding Ribonucleases RNase Y and RNase J1 Are Viable, with Major Defects in Cell Morphology, Sporulation, and Competence

PubMed Central

Figaro, Sabine; Durand, Sylvain; Gilet, Laetitia; Cayet, Nadège; Sachse, Martin

2013-01-01

The genes encoding the ribonucleases RNase J1 and RNase Y have long been considered essential for Bacillus subtilis cell viability, even before there was concrete knowledge of their function as two of the most important enzymes for RNA turnover in this organism. Here we show that this characterization is incorrect and that ΔrnjA and Δrny mutants are both viable. As expected, both strains grow relatively slowly, with doubling times in the hour range in rich medium. Knockout mutants have major defects in their sporulation and competence development programs. Both mutants are hypersensitive to a wide range of antibiotics and have dramatic alterations to their cell morphologies, suggestive of cell envelope defects. Indeed, RNase Y mutants are significantly smaller in diameter than wild-type strains and have a very disordered peptidoglycan layer. Strains lacking RNase J1 form long filaments in tight spirals, reminiscent of mutants of the actin-like proteins (Mre) involved in cell shape determination. Finally, we combined the rnjA and rny mutations with mutations in other components of the degradation machinery and show that many of these strains are also viable. The implications for the two known RNA degradation pathways of B. subtilis are discussed. PMID:23504012

Embryonic exposure to propylthiouracil disrupts left-right patterning in Xenopus embryos.

PubMed

van Veenendaal, Nicole R; Ulmer, Bärbel; Boskovski, Marko T; Fang, Xiefan; Khokha, Mustafa K; Wendler, Christopher C; Blum, Martin; Rivkees, Scott A

2013-02-01

Antithyroid medications are the preferred therapy for the treatment of Graves' disease during pregnancy. Propylthiouracil (PTU) is favored over methimazole (MMI) due to potential teratogenic concerns with MMI. This study was to determine the teratogenic potential of MMI and PTU using a validated Xenopus tropicalis embryo model. Embryos were exposed to 1 mM PTU (EC(50)=0.88 mM), 1 mM MMI, or vehicle control (water) from stages 2 to 45. Treated embryos were examined for gross morphological defects, ciliary function, and gene expression by in situ hybridization. Exposure to PTU, but not MMI, led to cardiac and gut looping defects and shortening along the anterior-posterior axis. PTU exposure during gastrulation (stage 8-12.5) was identified as the critical period of exposure leading to left-right (LR) patterning defects. Abnormal cilia polarization, abnormal cilia-driven leftward flow at the gastrocoel roof plate (GRP), and aberrant expression of both Coco and Pitx2c were associated with abnormal LR symmetry observed following PTU exposure. PTU is teratogenic during late blastula, gastrulation, and neurulation; whereas MMI is not. PTU alters ciliary-driven flow and disrupts the normal genetic program involved in LR axis determination. These studies have important implications for women taking PTU during early pregnancy.

Experimental studies of irradiated and hydrogen implantation damaged reactor steels

NASA Astrophysics Data System (ADS)

Slugeň, Vladimír; Pecko, Stanislav; Sojak, Stanislav

2016-01-01

Radiation degradation of nuclear materials can be experimentally simulated via ion implantation. In our case, German reactor pressure vessel (RPV) steels were studied by positron annihilation lifetime spectroscopy (PALS). This unique non-destructive method can be effectively applied for the evaluation of microstructural changes and for the analysis of degradation of reactor steels due to neutron irradiation and proton implantation. Studied specimens of German reactor pressure vessel steels are originally from CARINA/CARISMA program. Eight specimens were measured in as-received state and two specimens were irradiated by neutrons in German experimental reactor VAK (Versuchsatomkraftwerk Kahl) in the 1980s. One of the specimens which was in as-received and neutron irradiated condition was also used for simulation of neutron damage by hydrogen nuclei implantation. Defects with the size of about 1-2 vacancies with relatively small contribution (with intensity on the level of 20-40 %) were observed in "as-received" steels. A significant increase in the size of the induced defects due to neutron damage was observed in the irradiated specimens resulting in 2-3 vacancies. The size and intensity of defects reached a similar level as in the specimens irradiated in the nuclear reactor due to the implantation of hydrogen ions with energies of 100 keV (up to the depth <500 nm).

Comparative study of irradiated and hydrogen implantation damaged German RPV steels from PAS point of view

NASA Astrophysics Data System (ADS)

Pecko, Stanislav; Sojak, Stanislav; Slugeň, Vladimír

2014-09-01

Commercial German reactor pressure vessel (RPV) steels were studied by positron annihilation lifetime spectroscopy (PALS). This unique non-destructive method can be effectively applied for the evaluation of microstructural changes and for the analysis of degradation of reactor steels due to neutron irradiation and proton implantation. Studied specimens of German reactor pressure vessel steels are originally from CARINA/CARISMA program. Eight specimens were measured in as-received state and two specimens were irradiated by neutrons in German experimental reactor VAK (Versuchsatomkraftwerk Kahl) in the 1980s. One of the specimens which was also in as-received and neutron irradiated condition was also used for simulation of neutron damage by hydrogen nuclei implantation. Defects with the size of about 1-2 vacancies with relatively small contribution (with intensity on the level of 20-40%) were observed in "as-received" steels. A significant increase in the size of the induced defects due to neutron damage was observed at a level of 2-3 vacancies in the irradiated specimens. The size and intensity of defects reached a similar level as in the specimens irradiated in nuclear reactor due to hydrogen ions implantation with energy of 100 keV (up to the depth <500 nm). This could confirm the ability to simulate neutron damage by ion implantation.

The telomeric protein SNM1B/Apollo is required for normal cell proliferation and embryonic development

PubMed Central

Akhter, Shamima; Lam, Yung C.; Chang, Sandy; Legerski, Randy J.

2013-01-01

Summary Conserved metallo β-Lactamase and β-CASP (CPSF-Artemis-Snm1-Pso2) domain nuclease family member SNM1B/Apollo is a shelterin-associated protein that localizes to telomeres through its interaction with TRF2. To study its in vivo role, we generated a knockout of SNM1B/Apollo in a mouse model. Snm1B/Apollo homozygous null mice die at birth with developmental delay and defects in multiple organ systems. Cell proliferation defects were observed in Snm1B/Apollo mutant mouse embryonic fibroblasts (MEFs) owing to high levels of telomeric end-to-end fusions. Deficiency of the nonhomologous end-joining (NHEJ) factor Ku70, but not p53, rescued the developmental defects and lethality observed in Snm1B/Apollo mutant mice as well as the impaired proliferation of Snm1B/Apollo-deficient MEFs. These findings demonstrate that SNM1B/Apollo is required to protect telomeres against NHEJ-mediated repair, which results in genomic instability and the consequent multi-organ developmental failure. Although Snm1B/Apollo-deficient MEFs exhibited high levels of apoptosis, abrogation of p53-dependent programmed cell death did not rescue the multi-organ developmental failure in the mice. PMID:20854421

Medical Surveillance Monthly Report (MSMR). Volume 19, Number 3, March 2012

DTIC Science & Technology

2012-03-01

Type 7 Vaccine, Live, Oral (adenovirus vaccine).16 Th e two- tablet adenovirus vaccine was introduced to incoming trainees at recruit training centers...8oC. With minor exceptions, vaccine administration has proceeded smoothly. One trainee chewed a tablet , but no ill eff ects were noted. Th ree... tablets had minor defects related to imper- fect coating and were returned to the man- ufacturer who implemented a 100 percent inspection program. Febrile

Avionics Integrity Program (AVIP). Volume 1. Procurement Phase Issues - Design, Manufacturing, and Integration

DTIC Science & Technology

1984-03-01

Engineering initiative to develop an orderly plan and procedure to assure that USAF acquire reliable, high quality, supportable avionics with a higher avail...susceptibility te~t~ (radiated and conducted), and emission of radio frequency energy tests."l6) Other electrical stresses can include over/under voltage...jo ints, poor welds, and dielectric defects. Also, instruments with components unable to endu very high temperatures can be safely tested. 1-19

Maximum likelihood estimation of signal detection model parameters for the assessment of two-stage diagnostic strategies.

PubMed

Lirio, R B; Dondériz, I C; Pérez Abalo, M C

1992-08-01

The methodology of Receiver Operating Characteristic curves based on the signal detection model is extended to evaluate the accuracy of two-stage diagnostic strategies. A computer program is developed for the maximum likelihood estimation of parameters that characterize the sensitivity and specificity of two-stage classifiers according to this extended methodology. Its use is briefly illustrated with data collected in a two-stage screening for auditory defects.

HgCdTe Surface and Defect Study Program.

DTIC Science & Technology

1983-07-01

RESkSTIVITY. Rm T 10 12 10> 9 i0 1 0 9 I i i i i TI/Au TI AI/Ni Ti/Ni In GATE METAL Figure 8. The Effect of Gate " fetal Type on dc Resistivity of 1500.4...2. J.A. Wilson, V.A. Cotton, J.A. Silkerman, 0. Lacer , W.E. Spicer and P. Morgen, J. Vac. Sci. Tech., Al (1983), 1719. 3. B.K. Janorsek, R.C

Wavelet Spectral Finite Elements for Wave Propagation in Composite Plates with Damages - Years 3-4

DTIC Science & Technology

2014-05-23

study of Lamb wave interactions with holes and through thickness defects in thin metal plates . Distribution Code A: Approved for public release...Propagation in Composite Plates with Damages - Years 3-4 5a. CONTRACT NUMBER 5b. GRANT NUMBER FA23861214005 5c. PROGRAM ELEMENT NUMBER 6...14. ABSTRACT The objective of the proposed efforts: -Formulated Wavelet Spectral element for a healthy composite plates and used the formulated

Large area silicon sheet by EFG

NASA Technical Reports Server (NTRS)

Morrison, A. D.; Ravi, K. V.; Rao, C. V. H.; Surek, T.; Bliss, D. F.; Garone, L. C.; Hogencamp, R. W.

1976-01-01

Progress in a program to produce high speed, thin, wide silicon sheets for fabricating 10% efficient solar cells is reported. An EFG ribbon growth system was used to perform growth rate and ribbon thickness experiments. A new, wide ribbon growth system was developed. A theoretical study of stresses in ribbons was also conducted. The EFG ribbons were observed to exhibit a characteristic defect structure which is orientation dependent in the early stages of growth.

Ceramic Gas Turbine Engine Demonstration Program

DTIC Science & Technology

1982-05-01

of Radiographs 124 5.2.3 Ultrasonic NDE 127 5.2.4 Scanning Laser Acoustic Microscopy 132 5.2.5 Microwave NDE 134 5.2.6 Neutron Radiography 134 5.2.7...microwaves, and scanning loser acoustic microscopy (SLAM) were evaluated using the standards containing known defects. Component shape standards...mounted in a carousel and rotated in the high velocity combustor gases. The temperature is measured by an infrared pyrometer 95 TABLE 4-3. SUMMARY OF

Software for Processing of Digitized Astronegatives from Archives and Databases of Virtual Observatory

NASA Astrophysics Data System (ADS)

Protsyuk, Yu. I.; Andruk, V. N.; Kazantseva, L. V.

The paper discusses and illustrates the steps of basic processing of digitized image of astro negatives. Software for obtaining of a rectangular coordinates and photometric values of objects on photographic plates was created in the environment LINUX / MIDAS / ROMAFOT. The program can automatically process the specified number of files in FITS format with sizes up to 20000 x 20000 pixels. Other programs were made in FORTRAN and PASCAL with the ability to work in an environment of LINUX or WINDOWS. They were used for: identification of stars, separation and exclusion of diffraction satellites and double and triple exposures, elimination of image defects, reduction to the equatorial coordinates and magnitudes of a reference catalogs.

Defect reduction for semiconductor memory applications using jet and flash imprint lithography

NASA Astrophysics Data System (ADS)

Ye, Zhengmao; Luo, Kang; Lu, Xiaoming; Fletcher, Brian; Liu, Weijun; Xu, Frank; LaBrake, Dwayne; Resnick, Douglas J.; Sreenivasan, S. V.

2012-07-01

Acceptance of imprint lithography for manufacturing will require demonstration that it can attain defect levels commensurate with the defect specifications of high-end memory devices. Defects occurring during imprinting can generally be broken into two categories; random defects and repeating defects. Examples of random defects include fluid phase imprint defects, such as bubbles, and solid phase imprint defects, such as line collapse. Examples of repeater defects include mask fabrication defects and particle induced defects. Previous studies indicated that soft particles cause nonrepeating defects. Hard particles, on the other hand, can cause either permanent resist plugging or mask damage. In a previous study, two specific defect types were examined; random nonfill defects occurring during the resist filling process and repeater defects caused by interactions with particles on the substrate. We attempted to identify the different types of imprint defect types using a mask with line/space patterns at dimensions as small as 26 nm. An Imprio 500 twenty-wafer per hour development tool was used to study the various defect types. The imprint defect density was reduced nearly four orders of magnitude, down to ˜4/cm2 in a period of two years following the availability of low defect imprint masks at 26-nm half-pitch. This reduction was achieved by identifying the root cause of various defects and then taking the appropriate corrective action.

Defining defect specifications to optimize photomask production and requalification

NASA Astrophysics Data System (ADS)

Fiekowsky, Peter

2006-10-01

Reducing defect repairs and accelerating defect analysis is becoming more important as the total cost of defect repairs on advanced masks increases. Photomask defect specs based on printability, as measured on AIMS microscopes has been used for years, but the fundamental defect spec is still the defect size, as measured on the photomask, requiring the repair of many unprintable defects. ADAS, the Automated Defect Analysis System from AVI is now available in most advanced mask shops. It makes the use of pure printability specs, or "Optimal Defect Specs" practical. This software uses advanced algorithms to eliminate false defects caused by approximations in the inspection algorithm, classify each defect, simulate each defect and disposition each defect based on its printability and location. This paper defines "optimal defect specs", explains why they are now practical and economic, gives a method of determining them and provides accuracy data.

Racial-Ethnic Disparities in Acute Stroke Care in the Florida-Puerto Rico Collaboration to Reduce Stroke Disparities Study.

PubMed

Sacco, Ralph L; Gardener, Hannah; Wang, Kefeng; Dong, Chuanhui; Ciliberti-Vargas, Maria A; Gutierrez, Carolina M; Asdaghi, Negar; Burgin, W Scott; Carrasquillo, Olveen; Garcia-Rivera, Enid J; Nobo, Ulises; Oluwole, Sofia; Rose, David Z; Waters, Michael F; Zevallos, Juan Carlos; Robichaux, Mary; Waddy, Salina P; Romano, Jose G; Rundek, Tatjana

2017-02-14

Racial-ethnic disparities in acute stroke care can contribute to inequality in stroke outcomes. We examined race-ethnic disparities in acute stroke performance metrics in a voluntary stroke registry among Florida and Puerto Rico Get With the Guidelines-Stroke hospitals. Seventy-five sites in the Florida Puerto Rico Stroke Registry (66 Florida and 9 Puerto Rico) recorded 58 864 ischemic stroke cases (2010-2014). Logistic regression models examined racial-ethnic differences in acute stroke performance measures and defect-free care (intravenous tissue plasminogen activator treatment, in-hospital antithrombotic therapy, deep vein thrombosis prophylaxis, discharge antithrombotic therapy, appropriate anticoagulation therapy, statin use, smoking cessation counseling) and temporal trends. Among ischemic stroke cases, 63% were non-Hispanic white (NHW), 18% were non-Hispanic black (NHB), 14% were Hispanic living in Florida, and 6% were Hispanic living in Puerto Rico. NHW patients were the oldest, followed by Hispanics, and NHBs. Defect-free care was greatest among NHBs (81%), followed by NHWs (79%) and Florida Hispanics (79%), then Puerto Rico Hispanics (57%) ( P <0.0001). Puerto Rico Hispanics were less likely than Florida whites to meet any stroke care performance metric other than anticoagulation. Defect-free care improved for all groups during 2010-2014, but the disparity in Puerto Rico persisted (2010: NHWs=63%, NHBs=65%, Florida Hispanics=59%, Puerto Rico Hispanics=31%; 2014: NHWs=93%, NHBs=94%, Florida Hispanics=94%, Puerto Rico Hispanics=63%). Racial-ethnic/geographic disparities were observed for acute stroke care performance metrics. Adoption of a quality improvement program improved stroke care from 2010 to 2014 in Puerto Rico and all Florida racial-ethnic groups. However, stroke care quality delivered in Puerto Rico is lower than in Florida. Sustained support of evidence-based acute stroke quality improvement programs is required to improve stroke care and minimize racial-ethnic disparities, particularly in resource-strained Puerto Rico. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Frequency Domain Reflectometry NDE for Aging Cables in Nuclear Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glass, Samuel W.; Jones, Anthony M.; Fifield, Leonard S.

Cable insulation polymers are among the more susceptible materials to age-related degradation within a nuclear power plant. This is recognized by both regulators and utilities, so all plants have developed cable aging management programs to detect damage before critical component failure in compliance with regulatory guidelines. Although a wide range of tools are available to evaluate cables and cable systems, cable aging management programs vary in how condition monitoring and nondestructive examinations are conducted as utilities search for the most reliable and cost-effective ways to assess cable system condition. Frequency domain reflectometry (FDR) is emerging as one valuable tool tomore » locate and assess damaged portions of a cable system with minimal cost and only requires access in most cases to one of the cable terminal ends. Since laboratory studies to evaluate the use of FDR for inspection of aged cables can be expensive and data interpretation may be confounded by multiple factors which influence results, a model-based approach is desired to parametrically investigate the effect of insulation material damage in a controlled manner. This work describes development of a physics-based FDR model which uses finite element simulations of cable segments in conjunction with cascaded circuit element simulations to efficiently study a cable system. One or more segments of the cable system model have altered physical or electrical properties which represent the degree of damage and the location of the damage in the system. This circuit model is then subjected to a simulated FDR examination. The modeling approach is verified using several experimental cases and by comparing it to a commercial simulator suitable for simulation of some cable configurations. The model is used to examine a broad range of parameters including defect length, defect profile, degree of degradation, number and location of defects, FDR bandwidth, and addition of impedance-matched extensions to minimize the end-shadow effect.« less

Frequency domain reflectometry modeling for nondestructive evaluation of nuclear power plant cables

NASA Astrophysics Data System (ADS)

Glass, S. W.; Fifield, L. S.; Jones, A. M.; Hartman, T. S.

2018-04-01

Cable insulation polymers are among the more susceptible materials to age-related degradation within a nuclear power plant. This is recognized by both regulators and utilities, so all plants have developed cable aging management programs to detect damage before critical component failure in compliance with regulatory guidelines. Although a wide range of tools are available to evaluate cables and cable systems, cable aging management programs vary in how condition monitoring and nondestructive examinations are conducted as utilities search for the most reliable and cost-effective ways to assess cable system condition. Frequency domain reflectometry (FDR) is emerging as one valuable tool to locate and assess damaged portions of a cable system with minimal cost and only requires access in most cases to one of the cable terminal ends. Since laboratory studies to evaluate the use of FDR for inspection of aged cables can be expensive and data interpretation may be confounded by multiple factors which influence results, a model-based approach is desired to parametrically investigate the effect of insulation material damage in a controlled manner. This work describes development of a physics-based FDR model which uses finite element simulations of cable segments in conjunction with cascaded circuit element simulations to efficiently study a cable system. One or more segments of the cable system model have altered physical or electrical properties which represent the degree of damage and the location of the damage in the system. This circuit model is then subjected to a simulated FDR examination. The modeling approach is verified using several experimental cases and by comparing it to a commercial simulator suitable for simulation of some cable configurations. The model is used to examine a broad range of parameters including defect length, defect profile, degree of degradation, number and location of defects, FDR bandwidth, and addition of impedance-matched extensions to minimize the end-shadow effect.

Considering genetic characteristics in German Holstein breeding programs.

PubMed

Segelke, D; Täubert, H; Reinhardt, F; Thaller, G

2016-01-01

Recently, several research groups have demonstrated that several haplotypes may cause embryonic loss in the homozygous state. Up to now, carriers of genetic disorders were often excluded from mating, resulting in a decrease of genetic gain and a reduced number of sires available for the breeding program. Ongoing research is very likely to identify additional genetic defects causing embryonic loss and calf mortality by genotyping a large proportion of the female cattle population and sequencing key ancestors. Hence, a clear demand is present to develop a method combining selection against recessive defects (e.g., Holstein haplotypes HH1-HH5) with selection for economically beneficial traits (e.g., polled) for mating decisions. Our proposed method is a genetic index that accounts for the allele frequencies in the population and the economic value of the genetic characteristic without excluding carriers from breeding schemes. Fertility phenotypes from routine genetic evaluations were used to determine the economic value per embryo lost. Previous research has shown that embryo loss caused by HH1 and HH2 occurs later than the loss for HH3, HH4, and HH5. Therefore, an economic value of € 97 was used against HH1 and HH2 and € 70 against HH3, HH4, and HH5. For polled, € 7 per polled calf was considered. Minor allele frequencies of the defects ranged between 0.8 and 3.3%. The polled allele has a frequency of 4.1% in the German Holstein population. A genomic breeding program was simulated to study the effect of changing the selection criteria from assortative mating based on breeding values to selecting the females using the genetic index. Selection for a genetic index on the female path is a useful method to control the allele frequencies by reducing undesirable alleles and simultaneously increasing economical beneficial characteristics maintaining most of the genetic gain in production and functional traits. Additionally, we applied the genetic index to real data and found a decrease of the genetic trend for the birth years 1990 to 2006. Since 2010 the genetic index has increased due to a strong increase in the polled frequency. However, further investigation is needed to better understand the biology to determine the correct time of embryo loss and the economic value of fertility disorders. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Perioperative outcomes for pediatric neurosurgical procedures: analysis of the National Surgical Quality Improvement Program-Pediatrics.

PubMed

Kuo, Benjamin J; Vissoci, Joao Ricardo N; Egger, Joseph R; Smith, Emily R; Grant, Gerald A; Haglund, Michael M; Rice, Henry E

2017-03-01

OBJECTIVE Existing studies have shown a high overall rate of adverse events (AEs) following pediatric neurosurgical procedures. However, little is known regarding the morbidity of specific procedures or the association with risk factors to help guide quality improvement (QI) initiatives. The goal of this study was to describe the 30-day mortality and AE rates for pediatric neurosurgical procedures by using the American College of Surgeons (ACS) National Surgical Quality Improvement Program-Pediatrics (NSQIP-Peds) database platform. METHODS Data on 9996 pediatric neurosurgical patients were acquired from the 2012-2014 NSQIP-Peds participant user file. Neurosurgical cases were analyzed by the NSQIP-Peds targeted procedure categories, including craniotomy/craniectomy, defect repair, laminectomy, shunts, and implants. The primary outcome measure was 30-day mortality, with secondary outcomes including individual AEs, composite morbidity (all AEs excluding mortality and unplanned reoperation), surgical-site infection, and unplanned reoperation. Univariate analysis was performed between individual AEs and patient characteristics using Fischer's exact test. Associations between individual AEs and continuous variables (duration from admission to operation, work relative value unit, and operation time) were examined using the Student t-test. Patient characteristics and continuous variables associated with any AE by univariate analysis were used to develop category-specific multivariable models through backward stepwise logistic regression. RESULTS The authors analyzed 3383 craniotomy/craniectomy, 242 defect repair, 1811 laminectomy, and 4560 shunt and implant cases and found a composite overall morbidity of 30.2%, 38.8%, 10.2%, and 10.7%, respectively. Unplanned reoperation rates were highest for defect repair (29.8%). The mortality rate ranged from 0.1% to 1.2%. Preoperative ventilator dependence was a significant predictor of any AE for all procedure groups, whereas admission from outside hospital transfer was a significant predictor of any AE for all procedure groups except craniotomy/craniectomy. CONCLUSIONS This analysis of NSQIP-Peds, a large risk-adjusted national data set, confirms low perioperative mortality but high morbidity for pediatric neurosurgical procedures. These data provide a baseline understanding of current expected clinical outcomes for pediatric neurosurgical procedures, identify the need for collecting neurosurgery-specific risk factors and complications, and should support targeted QI programs and clinical management interventions to improve care of children.

Developmental Programming: Impact of Prenatal Exposure to Bisphenol-A and Methoxychlor on Steroid Feedbacks in Sheep

PubMed Central

Salloum, Bachir Abi; Steckler, Teresa L.; Herkimer, Carol; Lee, James S.; Padmanabhan, Vasantha

2013-01-01

Bisphenol-A (BPA), a polymer used in plastics manufacturing, and methochychlor (MXC) a pesticide, are endocrine disrupting compounds with estrogenic and anti-androgenic properties. Prenatal BPA or MXC treatment induces reproductive defects in sheep with BPA causing prepubertal luteinizing hormone (LH) hypersecretion and dampening of periovulatory LH surges and MXC lengthening follicular phase and delaying the LH surge. In this study, we addressed the underlying neuroendocrine defects by testing the following hypotheses: 1) prenatal BPA but not MXC reduces sensitivity to estradiol and progesterone negative feedback, 2) prenatal BPA but not MXC increases pituitary responsiveness to gonadotropin releasing hormone (GnRH), and 3) prenatal BPA dampens LH surge response to estradiol positive feedback challenge while prenatal MXC delays the timing of the LH surge. Pregnant sheep were treated with either 1) 5 mg/kg/day BPA (produces approximately twice the level found in human circulation, n=8), 2) 5 mg/kg/day MXC (lowest observed effect level stated in the EPA National Toxicology Program’s Report; n=6), or 3) vehicle (cotton seed oil: C: n=6) from days 30 to 90 of gestation. Female offspring of these ewes were ovariectomized at 21 months of age and tested for progesterone negative, estradiol negative, estradiol positive feedback sensitivities and pituitary responsiveness to GnRH. Results revealed that sensitivity to all 3 feedbacks as well as pituitary responsiveness to GnRH were not altered by either of the prenatal treatments. These findings suggest that the postpubertal reproductive defects seen in these animals may have stemmed from ovarian defects and the steroidal signals emanating from them. PMID:23454450

Markers of Vascular Perturbation Correlate with Airway Structural Change in Asthma

PubMed Central

Kruger, Stanley J.; Schiebler, Mark L.; Evans, Michael D.; Sorkness, Ronald L.; Denlinger, Loren C.; Busse, William W.; Jarjour, Nizar N.; Montgomery, Robert R.; Mosher, Deane F.; Fain, Sean B.

2013-01-01

Rationale: Air trapping and ventilation defects on imaging are characteristics of asthma. Airway wall thickening occurs in asthma and is associated with increased bronchial vascularity and vascular permeability. Vascular endothelial cell products have not been explored as a surrogate to mark structural airway changes in asthma. Objectives: Determine whether reporters of vascular endothelial cell perturbation correlate with airway imaging metrics in patients with asthma of varying severity. Methods: Plasma from Severe Asthma Research Program subjects was analyzed by ELISAs for soluble von Willebrand factor mature protein (VWF:Ag) and propeptide (VWFpp), P-selectin, and platelet factor 4. Additional subjects were analyzed over 48 hours after whole-lung antigen challenge. We calculated ventilation defect volume by hyperpolarized helium-3 magnetic resonance imaging and areas of low signal density by multidetector computed tomography (less than −856 Hounsfield units [HU] at functional residual capacity and −950 HU at total lung capacity [TLC]). Measurements and Main Results: VWFpp and VWFpp/Ag ratio correlated with and predicted greater percentage defect volume on hyperpolarized helium-3 magnetic resonance imaging. P-selectin correlated with and predicted greater area of low density on chest multidetector computed tomography less than −950 HU at TLC. Platelet factor 4 did not correlate. Following whole-lung antigen challenge, variation in VWFpp, VWFpp/Ag, and P-selectin among time-points was less than that among subjects, indicating stability and repeatability of the measurements. Conclusions: Plasma VWFpp and P-selectin may be useful as surrogates of functional and structural defects that are evident on imaging. The results raise important questions about why VWFpp and P-selectin are associated specifically with different imaging abnormalities. PMID:23855693

Results From the New Jersey Statewide Critical Congenital Heart Defects Screening Program

PubMed Central

Garg, Lorraine F.; Van Naarden Braun, Kim; Knapp, Mary M.; Anderson, Terry M.; Koppel, Robert I.; Hirsch, Daniel; Beres, Leslie M.; Hyg, MS; Sweatlock, Joseph; Olney, Richard S.; Glidewell, Jill; Hinton, Cynthia F.; Kemper, Alex R.

2015-01-01

BACKGROUND AND OBJECTIVE New Jersey was the first state to implement legislatively mandated newborn pulse oximetry screening (POxS) in all licensed birthing facilities to detect critical congenital heart defects (CCHDs). The objective of this report was to evaluate implementation of New Jersey’s statewide POxS mandate. METHODS A 2-pronged approach was used to collect data on infants screened in all New Jersey birthing facilities from August 31, 2011, through May 31, 2012. Aggregate screening results were submitted by each birthing facility. Data on failed screens and clinical characteristics of those newborns were reported to the New Jersey Birth Defects Registry (NJBDR). Three indicators were used to distinguish the added value of mandated POxS from standard clinical care: prenatal congenital heart defect diagnosis, cardiology consultation or echocardiogram indicated or performed before PoxS, or clinical findings at the time of POxS warranting a pulse oximetry measurement. RESULTS Of 75 324 live births in licensed New Jersey birthing facilities, 73 320 were eligible for screening, of which 99% were screened. Forty-nine infants with failed POxS were reported to the NJBDR, 30 of whom had diagnostic evaluations solely attributable to the mandated screening. Three of the 30 infants had previously unsuspected CCHDs and 17 had other diagnoses or non-CCHD echocardiogram findings. CONCLUSIONS In the first 9 months after implementation, New Jersey achieved a high statewide screening rate and established surveillance mechanisms to evaluate the unique contribution of POxS. The screening mandate identified 3 infants with previously unsuspected CCHDs that otherwise might have resulted in significant morbidity and mortality and also identified other significant secondary targets such as sepsis and pneumonia. PMID:23858425

Activation of the Hedgehog Signaling Pathway in the Developing Lens Stimulates Ectopic FoxE3 Expression and Disruption in Fiber Cell Differentiation

PubMed Central

Kerr, Christine L.; Huang, Jian; Williams, Trevor; West-Mays, Judith A.

2012-01-01

Purpose. The signaling pathways and transcriptional effectors responsible for directing mammalian lens development provide key regulatory molecules that can inform our understanding of human eye defects. The hedgehog genes encode extracellular signaling proteins responsible for patterning and tissue formation during embryogenesis. Signal transduction of this pathway is mediated through activation of the transmembrane proteins smoothened and patched, stimulating downstream signaling resulting in the activation or repression of hedgehog target genes. Hedgehog signaling is implicated in eye development, and defects in hedgehog signaling components have been shown to result in defects of the retina, iris, and lens. Methods. We assessed the consequences of constitutive hedgehog signaling in the developing mouse lens using Cre-LoxP technology to express the conditional M2 smoothened allele in the embryonic head and lens ectoderm. Results. Although initial lens development appeared normal, morphological defects were apparent by E12.5 and became more significant at later stages of embryogenesis. Altered lens morphology correlated with ectopic expression of FoxE3, which encodes a critical gene required for human and mouse lens development. Later, inappropriate expression of the epithelial marker Pax6, and as well as fiber cell markers c-maf and Prox1 also occurred, indicating a failure of appropriate lens fiber cell differentiation accompanied by altered lens cell proliferation and cell death. Conclusions. Our findings demonstrate that the ectopic activation of downstream effectors of the hedgehog signaling pathway in the mouse lens disrupts normal fiber cell differentiation by a mechanism consistent with a sustained epithelial cellular developmental program driven by FoxE3. PMID:22491411

Advanced mask cleaning for 0.20-μm technology: an integrated user-supplier approach

NASA Astrophysics Data System (ADS)

Poschenrieder, Rudolf; Hay, Bernd; Beier, Matthias; Hourd, Andrew C.; Stuemer, Harald; Gairing, Thomas M.

1998-12-01

A newly developed photomask final cleaning system, STEAG HamaTech's Advanced Single Substrate Cleaner, ASC 500, was assessed and optimized at the Siemens mask shop in Munich, Germany, under production conditions within the Esprit European Semiconductor Equipment Assessment programme (SEA). The project was carried out together with the active participation of Compugraphics Intl. Ltd. (UK), DuPont Photomasks, Inc. (Germany; Photronics-MZD, Germany). The results of the assessment are presented, focusing on the cleaning performance at the 0.25 micrometer defect level on photomasks, equipment reliability and Cost of Ownership data. A reticle free of soft defects on glass and on chrome down to the 0.25 micrometer level requires an excellent cleaning process and the use of high-end inspection tools like the KLA STARlight. In order to get a full understanding of the nature of the detected features additional investigations on the blank quality have been carried out. These investigations include the questions whether a detection is a hard or a soft defect and whether small defects on chrome are able to move on the reticle surface. Final cleaning recipes have been optimized in respect to cleaning efficiency while maintaining high throughput and low Cost of Ownership. A benchmark comparison against other final cleaning tools at the partner's maskshops showed the leading data of the ASC 500. It was found that a cleaning program which includes several substrate flips and a combination of the available cleaning methods acid- dispense, water pressure jet clean, brush and megasonic clean was best suitable to achieve these goals. In particular the use of the brush unit was shown to improve the yield while not adding damage to the plate.

High level of APOBEC3F/3G editing in HIV-2 DNA vif and pol sequences from antiretroviral-naive patients.

PubMed

Bertine, Mélanie; Charpentier, Charlotte; Visseaux, Benoit; Storto, Alexandre; Collin, Gilles; Larrouy, Lucile; Damond, Florence; Matheron, Sophie; Brun-Vézinet, Françoise; Descamps, Diane

2015-04-24

In HIV-1, hypermutation introduced by APOBEC3F/3G cytidine deaminase activity leads to defective viruses. In-vivo impact of APOBEC3F/3G editing on HIV-2 sequences remains unknown. The objective of this study was to assess the level of APOBEC3F/3G editing in HIV-2-infected antiretroviral-naive patients. Direct sequencing of vif and pol regions was performed on HIV-2 proviral DNA from antiretroviral-naive patients included in the French Agence Nationale de Recherches sur le SIDA et les hépatites virales CO5 HIV-2 cohort. Hypermutated sequences were identified using Hypermut2.0 program. HIV-1 proviral sequences from Genbank were also assessed. Among 82 antiretroviral-naive HIV-2-infected patients assessed, 15 (28.8%) and five (16.7%) displayed Vif proviral defective sequences in HIV-2 groups A and B, respectively. A lower proportion of defective sequences was observed in protease-reverse transcriptase region. A higher median number of G-to-A mutations was observed in HIV-2 group B than in group A, both in Vif and protease-reverse transcriptase regions (P = 0.02 and P = 0.006, respectively). Compared with HIV-1 Vif sequences, a higher number of Vif defective sequences was observed in HIV-2 group A (P = 0.00001) and group B sequences (P = 0.013). We showed for the first time a high level of APOBEC3F/3G editing in HIV-2 sequences from antiretroviral-naive patients. Our study reported a group effect with a significantly higher level of APOBEC3F/3G editing in HIV-2 group B than in group A sequences.

Context-based automated defect classification system using multiple morphological masks

DOEpatents

Gleason, Shaun S.; Hunt, Martin A.; Sari-Sarraf, Hamed

2002-01-01

Automatic detection of defects during the fabrication of semiconductor wafers is largely automated, but the classification of those defects is still performed manually by technicians. This invention includes novel digital image analysis techniques that generate unique feature vector descriptions of semiconductor defects as well as classifiers that use these descriptions to automatically categorize the defects into one of a set of pre-defined classes. Feature extraction techniques based on multiple-focus images, multiple-defect mask images, and segmented semiconductor wafer images are used to create unique feature-based descriptions of the semiconductor defects. These feature-based defect descriptions are subsequently classified by a defect classifier into categories that depend on defect characteristics and defect contextual information, that is, the semiconductor process layer(s) with which the defect comes in contact. At the heart of the system is a knowledge database that stores and distributes historical semiconductor wafer and defect data to guide the feature extraction and classification processes. In summary, this invention takes as its input a set of images containing semiconductor defect information, and generates as its output a classification for the defect that describes not only the defect itself, but also the location of that defect with respect to the semiconductor process layers.

SEMATECH EUVL mask program status

NASA Astrophysics Data System (ADS)

Yun, Henry; Goodwin, Frank; Huh, Sungmin; Orvek, Kevin; Cha, Brian; Rastegar, Abbas; Kearney, Patrick

2009-04-01

As we approach the 22nm half-pitch (hp) technology node, the industry is rapidly running out of patterning options. Of the several lithography techniques highlighted in the International Technology Roadmap for Semiconductors (ITRS), the leading contender for the 22nm hp insertion is extreme ultraviolet lithography (EUVL). Despite recent advances with EUV resist and improvements in source power, achieving defect free EUV mask blank and enabling the EUV mask infrastructure still remain critical issues. To meet the desired EUV high volume manufacturing (HVM) insertion target date of 2013, these obstacles must be resolved on a timely bases. Many of the EUV mask related challenges remain in the pre-competitive stage and a collaborative industry based consortia, such as SEMATECH can play an important role to enable the EUVL landscape. SEMATECH based in Albany, NY is an international consortium representing several of the largest manufacturers in the semiconductor market. Full members include Intel, Samsung, AMD, IBM, Panasonic, HP, TI, UMC, CNSE (College of Nanoscience and Engineering), and Fuller Road Management. Within the SEMATECH lithography division a major thrust is centered on enabling the EUVL ecosystem from mask development, EUV resist development and addressing EUV manufacturability concerns. An important area of focus for the SEMATECH mask program has been the Mask Blank Development Center (MBDC). At the MBDC key issues in EUV blank development such as defect reduction and inspection capabilities are actively pursued together with research partners, key suppliers and member companies. In addition the mask program continues a successful track record of working with the mask community to manage and fund critical mask tools programs. This paper will highlight recent status of mask projects and longer term strategic direction at the MBDC. It is important that mask technology be ready to support pilot line development HVM by 2013. In several areas progress has been made but a continued collaborative effort will be needed along with timely infrastructure investments to meet these challenging goals.

Care and outcomes of Asian-American acute myocardial infarction patients: findings from the American Heart Association Get With The Guidelines-Coronary Artery Disease program.

PubMed

Qian, Feng; Ling, Frederick S; Deedwania, Prakash; Hernandez, Adrian F; Fonarow, Gregg C; Cannon, Christopher P; Peterson, Eric D; Peacock, W Frank; Kaltenbach, Lisa A; Laskey, Warren K; Schwamm, Lee H; Bhatt, Deepak L

2012-01-01

Asian-Americans represent an important United States minority population, yet there are limited data regarding the clinical care and outcomes of Asian-Americans following acute myocardial infarction (AMI). Using data from the American Heart Association Get With The Guidelines-Coronary Artery Disease (GWTG-CAD) program, we compared use of and trends in evidence-based care AMI processes and outcome in Asian-American versus white patients. We analyzed 107,403 AMI patients (4412 Asian-Americans, 4.1%) from 382 United States centers participating in the Get With The Guidelines-Coronary Artery Disease program between 2003 and 2008. Use of 6 AMI performance measures, composite "defect-free" care (proportion receiving all eligible performance measures), door-to-balloon time, and in-hospital mortality were examined. Trends in care over this time period were explored. Compared with whites, Asian-American AMI patients were significantly older, more likely to be covered by Medicaid and recruited in the west region, and had a higher prevalence of diabetes, hypertension, heart failure, and smoking. In-hospital unadjusted mortality was higher among Asian-American patients. Overall, Asian-Americans were comparable with whites regarding the baseline quality of care, except that Asian-Americans were less likely to get smoking cessation counseling (65.6% versus 81.5%). Asian-American AMI patients experienced improvement in the 6 individual measures (P≤0.048), defect-free care (P<0.001), and door-to-balloon time (P<0.001). The improvement rates were similar for both Asian-Americans and whites. Compared with whites, the adjusted in-hospital mortality rate was higher for Asian-Americans (adjusted relative risk: 1.16; 95% confidence interval: 1.00-1.35; P=0.04). Evidence-based care for AMI processes improved significantly over the period of 2003 to 2008 for Asian-American and white patients in the Get With The Guidelines-Coronary Artery Disease program. Differences in care between Asian-Americans and whites, when present, were reduced over time.

Prevention of neural tube defects with folic acid: The Chinese experience.

PubMed

Ren, Ai-Guo

2015-08-08

Neural tube defects (NTDs) are a group of congenital malformations of the central nervous system that are caused by the closure failure of the embryonic neural tube by the 28(th) day of conception. Anencephaly and spina bifida are the two major subtypes. Fetuses with anencephaly are often stillborn or electively aborted due to prenatal diagnosis, or they die shortly after birth. Most infants with spina bifida are live-born and, with proper surgical treatment, can survive into adulthood. However, these children often have life-long physical disabilities. China has one of the highest prevalence of NTDs in the world. Inadequate dietary folate intake is believed to be the main cause of the cluster. Unlike many other countries that use staple fortification with folic acid as the public health strategy to prevent NTDs, the Chinese government provides all women who have a rural household registration and who plan to become pregnant with folic acid supplements, free of charge, through a nation-wide program started in 2009. Two to three years after the initiation of the program, the folic acid supplementation rate increased to 85% in the areas of the highest NTD prevalence. The mean plasma folate level of women during early and mid-pregnancy doubled the level before the program was introduced. However, most women began taking folic acid supplements when they knew that they were pregnant. This is too late for the protection of the embryonic neural tube. In a post-program survey of the women who reported folic acid supplementation, less than a quarter of the women began taking supplements prior to pregnancy, indicating that the remaining three quarters of the fetuses remained unprotected during the time of neural tube formation. Therefore, staple food fortification with folic acid should be considered as a priority in the prevention of NTDs.

On-Orbit Software Analysis

NASA Technical Reports Server (NTRS)

Moran, Susanne I.

2004-01-01

The On-Orbit Software Analysis Research Infusion Project was done by Intrinsyx Technologies Corporation (Intrinsyx) at the National Aeronautics and Space Administration (NASA) Ames Research Center (ARC). The Project was a joint collaborative effort between NASA Codes IC and SL, Kestrel Technology (Kestrel), and Intrinsyx. The primary objectives of the Project were: Discovery and verification of software program properties and dependencies, Detection and isolation of software defects across different versions of software, and Compilation of historical data and technical expertise for future applications

Gabriella Miller Kids First (GMKF/Kids First) Pediatric Research Program | Office of Cancer Genomics

Cancer.gov

The Gabriella Miller Kids First initiative is a trans-NIH effort to increase understanding of genetic changes associated with certain devastating pediatric conditions. The initiative will develop a centralized database of well-curated clinical and genetic sequence data from childhood cancer and structural birth defects cohorts comprising thousands of patients and their families. To learn more about the initiative and the data available, please visit https://commonfund.nih.gov/kidsfirst

[Feasibility of device closure for multiple atrial septal defects using 3D printing and ultrasound-guided intervention technique].

PubMed

Qiu, X; Lü, B; Xu, N; Yan, C W; Ouyang, W B; Liu, Y; Zhang, F W; Yue, Z Q; Pang, K J; Pan, X B

2017-04-25

Objective: To investigate the feasibility of trans-catheter closure of multiple atrial septal defects (ASD) monitored by trans-thoracic echocardiography (TTE) under the guidance of 3D printing heart model. Methods: Between April and August 2016, a total of 21 patients (8 male and 13 female) with multiple ASD in Fuwai Hospital of Chinese Academy of Medical Sciences underwent CT scan and 3-dimensional echocardiography for heart disease model produced by 3D printing technique. The best occlusion program was determined through the simulation test on the model. Percutaneous device closure of multiple ASD was performed follow the predetermined program guided by TTE. Clinical follow-up including electrocardiogram and TTE was arranged at 1 month after the procedure. Results: The trans-catheter procedure was successful in all 21 patients using a single atrial septal occluder. Mild residual shunt was found in 5 patient in the immediate postoperative period, 3 of them were disappeared during postoperative follow-up. There was no death, vascular damage, arrhythmia, device migration, thromboembolism, valvular dysfunction during the follow-up period. Conclusion: The use of 3D printing heart model provides a useful reference for transcatheter device closure of multiple ASD achieving through ultrasound-guided intervention technique, which appears to be safe and feasible with good outcomes of short-term follow-up.

The Caenorhabditis elegans mucolipin-like gene cup-5 is essential for viability and regulates lysosomes in multiple cell types.

PubMed

Hersh, Bradley M; Hartwieg, Erika; Horvitz, H Robert

2002-04-02

The misregulation of programmed cell death, or apoptosis, contributes to the pathogenesis of many diseases. We used Nomarski microscopy to screen for mutants containing refractile cell corpses in a C. elegans strain in which all programmed cell death is blocked and such corpses are absent. We isolated a mutant strain that accumulates refractile bodies resembling irregular cell corpses. We rescued this mutant phenotype with the C. elegans mucolipidosis type IV (ML-IV) homolog, the recently identified cup-5 (coelomocyte-uptake defective) gene. ML-IV is a human autosomal recessive lysosomal storage disease characterized by psychomotor retardation and ophthalmological abnormalities. Our null mutations in cup-5 cause maternal-effect lethality. In addition, cup-5 mutants contain excess lysosomes in many and possibly all cell types and contain lamellar structures similar to those observed in ML-IV cell lines. The human ML-IV gene is capable of rescuing both the maternal-effect lethality and the lysosome-accumulation abnormality of cup-5 mutants. cup-5 mutants seem to contain excess apoptotic cells as detected by staining with terminal deoxynucleotidyltransferase-mediated dUTP nick end labeling. We suggest that the increased apoptosis seen in cup-5 mutants is a secondary consequence of the lysosomal defect, and that abnormalities in apoptosis may be associated with human lysosomal storage disorders.

The effect of Ku on telomere replication time is mediated by telomere length but is independent of histone tail acetylation.

PubMed

Lian, Hui-Yong; Robertson, E Douglas; Hiraga, Shin-ichiro; Alvino, Gina M; Collingwood, David; McCune, Heather J; Sridhar, Akila; Brewer, Bonita J; Raghuraman, M K; Donaldson, Anne D

2011-05-15

DNA replication in Saccharomyces cerevisiae proceeds according to a temporal program. We have investigated the role of the telomere-binding Ku complex in specifying late replication of telomere-proximal sequences. Genome-wide analysis shows that regions extending up to 80 kb from telomeres replicate abnormally early in a yku70 mutant. We find that Ku does not appear to regulate replication time by binding replication origins directly, nor is its effect on telomere replication timing mediated by histone tail acetylation. We show that Ku instead regulates replication timing through its effect on telomere length, because deletion of the telomerase regulator Pif1 largely reverses the short telomere defect of a yku70 mutant and simultaneously rescues its replication timing defect. Consistent with this conclusion, deleting the genome integrity component Elg1 partially rescued both length and replication timing of yku70 telomeres. Telomere length-mediated control of replication timing requires the TG(1-3) repeat-counting component Rif1, because a rif1 mutant replicates telomeric regions early, despite having extended TG(1-3) tracts. Overall, our results suggest that the effect of Ku on telomere replication timing results from its impact on TG(1-3) repeat length and support a model in which Rif1 measures telomere repeat length to ensure that telomere replication timing is correctly programmed.

Scanning electron microscope automatic defect classification of process induced defects

NASA Astrophysics Data System (ADS)

Wolfe, Scott; McGarvey, Steve

2017-03-01

With the integration of high speed Scanning Electron Microscope (SEM) based Automated Defect Redetection (ADR) in both high volume semiconductor manufacturing and Research and Development (R and D), the need for reliable SEM Automated Defect Classification (ADC) has grown tremendously in the past few years. In many high volume manufacturing facilities and R and D operations, defect inspection is performed on EBeam (EB), Bright Field (BF) or Dark Field (DF) defect inspection equipment. A comma separated value (CSV) file is created by both the patterned and non-patterned defect inspection tools. The defect inspection result file contains a list of the inspection anomalies detected during the inspection tools' examination of each structure, or the examination of an entire wafers surface for non-patterned applications. This file is imported into the Defect Review Scanning Electron Microscope (DRSEM). Following the defect inspection result file import, the DRSEM automatically moves the wafer to each defect coordinate and performs ADR. During ADR the DRSEM operates in a reference mode, capturing a SEM image at the exact position of the anomalies coordinates and capturing a SEM image of a reference location in the center of the wafer. A Defect reference image is created based on the Reference image minus the Defect image. The exact coordinates of the defect is calculated based on the calculated defect position and the anomalies stage coordinate calculated when the high magnification SEM defect image is captured. The captured SEM image is processed through either DRSEM ADC binning, exporting to a Yield Analysis System (YAS), or a combination of both. Process Engineers, Yield Analysis Engineers or Failure Analysis Engineers will manually review the captured images to insure that either the YAS defect binning is accurately classifying the defects or that the DRSEM defect binning is accurately classifying the defects. This paper is an exploration of the feasibility of the utilization of a Hitachi RS4000 Defect Review SEM to perform Automatic Defect Classification with the objective of the total automated classification accuracy being greater than human based defect classification binning when the defects do not require multiple process step knowledge for accurate classification. The implementation of DRSEM ADC has the potential to improve the response time between defect detection and defect classification. Faster defect classification will allow for rapid response to yield anomalies that will ultimately reduce the wafer and/or the die yield.

Maternal high-fat diet and obesity compromise fetal hematopoiesis

PubMed Central

Kamimae-Lanning, Ashley N.; Krasnow, Stephanie M.; Goloviznina, Natalya A.; Zhu, Xinxia; Roth-Carter, Quinn R.; Levasseur, Peter R.; Jeng, Sophia; McWeeney, Shannon K.; Kurre, Peter; Marks, Daniel L.

2014-01-01

Objective Recent evidence indicates that the adult hematopoietic system is susceptible to diet-induced lineage skewing. It is not known whether the developing hematopoietic system is subject to metabolic programming via in utero high-fat diet (HFD) exposure, an established mechanism of adult disease in several organ systems. We previously reported substantial losses in offspring liver size with prenatal HFD. As the liver is the main hematopoietic organ in the fetus, we asked whether the developmental expansion of the hematopoietic stem and progenitor cell (HSPC) pool is compromised by prenatal HFD and/or maternal obesity. Methods We used quantitative assays, progenitor colony formation, flow cytometry, transplantation, and gene expression assays with a series of dietary manipulations to test the effects of gestational high-fat diet and maternal obesity on the day 14.5 fetal liver hematopoietic system. Results Maternal obesity, particularly when paired with gestational HFD, restricts physiological expansion of fetal HSPCs while promoting the opposing cell fate of differentiation. Importantly, these effects are only partially ameliorated by gestational dietary adjustments for obese dams. Competitive transplantation reveals compromised repopulation and myeloid-biased differentiation of HFD-programmed HSPCs to be a niche-dependent defect, apparent in HFD-conditioned male recipients. Fetal HSPC deficiencies coincide with perturbations in genes regulating metabolism, immune and inflammatory processes, and stress response, along with downregulation of genes critical for hematopoietic stem cell self-renewal and activation of pathways regulating cell migration. Conclusions Our data reveal a previously unrecognized susceptibility to nutritional and metabolic developmental programming in the fetal HSPC compartment, which is a partially reversible and microenvironment-dependent defect perturbing stem and progenitor cell expansion and hematopoietic lineage commitment. PMID:25685687

Localised surface plasmon-like resonance generated by microwave electromagnetic waves in pipe defects

NASA Astrophysics Data System (ADS)

Alobaidi, Wissam M.; Nima, Zeid A.; Sandgren, Eric

2018-01-01

Localised surface plasmon (LSP)-like resonance phenomena were simulated in COMSOL Multiphysics™, and the electric field enhancement was evaluated in eight pipe defects using the microwave band from 1.80 to 3.00 GHz and analysed by finite element analysis (FEA). The simulation was carried out, in each defect case, on a pipe that has 762 mm length and 152.4 mm inner diameter, and 12.7 mm pipe wall thickness. Defects were positioned in the middle of the pipe and were named as follows; SD: Square Defect, FCD: fillet corner defect, FD: fillet defect, HCD: half circle defect, TCD: triangle corner defect, TD: triangle defect, ZD: zigzag defect, GD: gear defect. The LSP electric field, and scattering parametric (S21, and S11) waves were evaluated in all cases and found to be strongly dependent on the size and the shape of the defect rather than the pipe and or the medium materials.

Programming Self-Assembly of DNA Origami Honeycomb Two-Dimensional Lattices and Plasmonic Metamaterials.

PubMed

Wang, Pengfei; Gaitanaros, Stavros; Lee, Seungwoo; Bathe, Mark; Shih, William M; Ke, Yonggang

2016-06-22

Scaffolded DNA origami has proven to be a versatile method for generating functional nanostructures with prescribed sub-100 nm shapes. Programming DNA-origami tiles to form large-scale 2D lattices that span hundreds of nanometers to the micrometer scale could provide an enabling platform for diverse applications ranging from metamaterials to surface-based biophysical assays. Toward this end, here we design a family of hexagonal DNA-origami tiles using computer-aided design and demonstrate successful self-assembly of micrometer-scale 2D honeycomb lattices and tubes by controlling their geometric and mechanical properties including their interconnecting strands. Our results offer insight into programmed self-assembly of low-defect supra-molecular DNA-origami 2D lattices and tubes. In addition, we demonstrate that these DNA-origami hexagon tiles and honeycomb lattices are versatile platforms for assembling optical metamaterials via programmable spatial arrangement of gold nanoparticles (AuNPs) into cluster and superlattice geometries.

The Role of Cerl2 in the Establishment of Left-Right Asymmetries during Axis Formation and Heart Development

PubMed Central

2017-01-01

The formation of the asymmetric left-right (LR) body axis is one of the fundamental aspects of vertebrate embryonic development, and one still raising passionate discussions among scientists. Although the conserved role of nodal is unquestionable in this process, several of the details around this signaling cascade are still unanswered. To further understand this mechanism, we have been studying Cerberus-like 2 (Cerl2), an inhibitor of Nodal, and its role in the generation of asymmetries in the early vertebrate embryo. The absence of Cerl2 results in a wide spectrum of malformations commonly known as heterotaxia, which comprises defects in either global organ position (e.g., situs inversus totalis), reversed orientation of at least one organ (e.g., situs ambiguus), and mirror images of usually asymmetric paired organs (e.g., left or right isomerisms of the lungs). Moreover, these laterality defects are frequently associated with congenital heart diseases (e.g., transposition of the great arteries, or atrioventricular septal defects). Here, reviewing the knowledge on the establishment of LR asymmetry in mouse embryos, the emerging conclusion is that as necessary as is the activation of the Nodal signaling cascade, the tight control that Cerl2-mediates on Nodal signaling is equally important, and that generates a further regionalized LR genetic program in the proper time and space. PMID:29367552

Progress on EUV mask fabrication for 32-nm technology node and beyond

NASA Astrophysics Data System (ADS)

Zhang, Guojing; Yan, Pei-Yang; Liang, Ted; Park, Seh-jin; Sanchez, Peter; Shu, Emily Y.; Ultanir, Erdem A.; Henrichs, Sven; Stivers, Alan; Vandentop, Gilroy; Lieberman, Barry; Qu, Ping

2007-05-01

Extreme ultraviolet lithography (EUVL) tool development achieved a big milestone last year as two full-field Alpha Demo Tools (ADT) were shipped to customers by ASML. In the future horizon, a full field "EUV1" exposure tool from Nikon will be available by the end of 20071 and the pre-production EUV exposure tools from ASML are targeted for 20092. It is essential that high quality EUVL masks can be made and delivered to the EUVL tool users to support the technology development. In the past year, we have demonstrated mask fabrication with low stress absorber deposition and good etch process control yielding a vertical etch profile and a mask CD control of 5.7 nm for 32 nm (1x) space and 7.4 nm for 32 nm (1x) lines. Mask pattern resolution of 15 nm (1x) dense lines was achieved. Full field reflective mask die-to-die inspection at a 125nm pixel size was demonstrated after low defect multilayer blanks became available. In this paper, we will present details of the Intel EUVL Mask Pilot Line progress in EUVL mask defect reduction, pattern CD performance, program defect mask design and inspection, in-house absorber film development and its performance, and EUVL metrology tool development. We will demonstrate an overall improvement in EUV mask manufacturing readiness due to our Pilot Line activities.

Structural Testing of the Blade Reliability Collaborative Effect of Defect Wind Turbine Blades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desmond, M.; Hughes, S.; Paquette, J.

Two 8.3-meter (m) wind turbine blades intentionally constructed with manufacturing flaws were tested to failure at the National Wind Technology Center (NWTC) at the National Renewable Energy Laboratory (NREL) south of Boulder, Colorado. Two blades were tested; one blade was manufactured with a fiberglass spar cap and the second blade was manufactured with a carbon fiber spar cap. Test loading primarily consisted of flap fatigue loading of the blades, with one quasi-static ultimate load case applied to the carbon fiber spar cap blade. Results of the test program were intended to provide the full-scale test data needed for validation ofmore » model and coupon test results of the effect of defects in wind turbine blade composite materials. Testing was part of the Blade Reliability Collaborative (BRC) led by Sandia National Laboratories (SNL). The BRC seeks to develop a deeper understanding of the causes of unexpected blade failures (Paquette 2012), and to develop methods to enable blades to survive to their expected operational lifetime. Recent work in the BRC includes examining and characterizing flaws and defects known to exist in wind turbine blades from manufacturing processes (Riddle et al. 2011). Recent results from reliability databases show that wind turbine rotor blades continue to be a leading contributor to turbine downtime (Paquette 2012).« less

The telomeric protein SNM1B/Apollo is required for normal cell proliferation and embryonic development.

PubMed

Akhter, Shamima; Lam, Yung C; Chang, Sandy; Legerski, Randy J

2010-12-01

Conserved metallo β-Lactamase and β-CASP (CPSF-Artemis-Snm1-Pso2) domain nuclease family member SNM1B/Apollo is a shelterin-associated protein that localizes to telomeres through its interaction with TRF2. To study its in vivo role, we generated a knockout of SNM1B/Apollo in a mouse model. Snm1B/Apollo homozygous null mice die at birth with developmental delay and defects in multiple organ systems. Cell proliferation defects were observed in Snm1B/Apollo mutant mouse embryonic fibroblasts (MEFs) owing to high levels of telomeric end-to-end fusions. Deficiency of the nonhomologous end-joining (NHEJ) factor Ku70, but not p53, rescued the developmental defects and lethality observed in Snm1B/Apollo mutant mice as well as the impaired proliferation of Snm1B/Apollo-deficient MEFs. These findings demonstrate that SNM1B/Apollo is required to protect telomeres against NHEJ-mediated repair, which results in genomic instability and the consequent multi-organ developmental failure. Although Snm1B/Apollo-deficient MEFs exhibited high levels of apoptosis, abrogation of p53-dependent programmed cell death did not rescue the multi-organ developmental failure in the mice. © 2010 The Authors. Aging Cell © 2010 Blackwell Publishing Ltd/Anatomical Society of Great Britain and Ireland.

Detection of Subsurface Defects in Levees in Correlation to Weather Conditions Utilizing Ground Penetrating Radar

NASA Astrophysics Data System (ADS)

Martinez, I. A.; Eisenmann, D.

2012-12-01

Ground Penetrating Radar (GPR) has been used for many years in successful subsurface detection of conductive and non-conductive objects in all types of material including different soils and concrete. Typical defect detection is based on subjective examination of processed scans using data collection and analysis software to acquire and analyze the data, often requiring a developed expertise or an awareness of how a GPR works while collecting data. Processing programs, such as GSSI's RADAN analysis software are then used to validate the collected information. Iowa State University's Center for Nondestructive Evaluation (CNDE) has built a test site, resembling a typical levee used near rivers, which contains known sub-surface targets of varying size, depth, and conductivity. Scientist at CNDE have developed software with the enhanced capabilities, to decipher a hyperbola's magnitude and amplitude for GPR signal processing. With this enhanced capability, the signal processing and defect detection capabilities for GPR have the potential to be greatly enhanced. This study will examine the effects of test parameters, antenna frequency (400MHz), data manipulation methods (which include data filters and restricting the range of depth in which the chosen antenna's signal can reach), and real-world conditions using this test site (such as varying weather conditions) , with the goal of improving GPR tests sensitivity for differing soil conditions.

Five-year speech and language outcomes in children with cleft lip-palate.

PubMed

Prathanee, Benjamas; Pumnum, Tawitree; Seepuaham, Cholada; Jaiyong, Pechcharat

2016-10-01

To investigate 5-year speech and language outcomes in children with cleft lip/palate (CLP). Thirty-eight children aged 4-7 years and 8 months were recruited for this study. Speech abilities including articulation, resonance, voice, and intelligibility were assessed based on Thai Universal Parameters of Speech Outcomes. Language ability was assessed by the Language Screening Test. The findings revealed that children with clefts had speech and language delay, abnormal understandability, resonance abnormality, and voice disturbance; articulation defects that were 8.33 (1.75, 22.47), 50.00 (32.92, 67.08), 36.11 (20.82, 53.78), 30.56 (16.35, 48.11), and 94.44 (81.34, 99.32). Articulation errors were the most common speech and language defects in children with clefts, followed by abnormal understandability, resonance abnormality, and voice disturbance. These results should be of critical concern. Protocol reviewing and early intervention programs are needed for improved speech outcomes. Copyright © 2016 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

The impact of environmental stress on male reproductive development in plants: biological processes and molecular mechanisms

PubMed Central

de Storme, Nico; Geelen, Danny

2014-01-01

In plants, male reproductive development is extremely sensitive to adverse climatic environments and (a)biotic stress. Upon exposure to stress, male gametophytic organs often show morphological, structural and metabolic alterations that typically lead to meiotic defects or premature spore abortion and male reproductive sterility. Depending on the type of stress involved (e.g. heat, cold, drought) and the duration of stress exposure, the underlying cellular defect is highly variable and either involves cytoskeletal alterations, tapetal irregularities, altered sugar utilization, aberrations in auxin metabolism, accumulation of reactive oxygen species (ROS; oxidative stress) or the ectopic induction of programmed cell death (PCD). In this review, we present the critically stress-sensitive stages of male sporogenesis (meiosis) and male gametogenesis (microspore development), and discuss the corresponding biological processes involved and the resulting alterations in male reproduction. In addition, this review also provides insights into the molecular and/or hormonal regulation of the environmental stress sensitivity of male reproduction and outlines putative interaction(s) between the different processes involved. PMID:23731015

Polycystin-1 Binds Par3/aPKC and Controls Convergent Extension During Renal Tubular Morphogenesis

PubMed Central

Castelli, Maddalena; Boca, Manila; Chiaravalli, Marco; Ramalingam, Harini; Rowe, Isaline; Distefano, Gianfranco; Carroll, Thomas; Boletta, Alessandra

2013-01-01

Several organs, including lungs and kidneys, are formed by epithelial tubes whose proper morphogenesis ensures correct function. This is best exemplified by the kidney, where defective establishment or maintanance of tubular diameter results in polycystic kidney disease, a common genetic disorder. Most polycystic kidney disease cases result from loss-of-function mutations in the PKD1 gene, encoding Polycystin-1 (PC-1), a large receptor of unknown function. Here we demonstrate that PC-1 plays an essential role in establishment of correct tubular diameter during nephron development. PC-1 associates with Par3 favoring the assembly of a pro-polarizing Par3/aPKC complex and it regulates a program of cell polarity important for oriented cell migration and for a convergent extension-like process during tubular morphogenesis. Par3 inactivation in the developing kidney results in defective convergent extension and tubular morphogenesis and in renal cyst formation. Our data define PC-1 as central to cell polarization and to epithelial tube morphogenesis and homeostasis. PMID:24153433

Defects in adaptive energy metabolism with CNS-linked hyperactivity in PGC-1alpha null mice.

PubMed

Lin, Jiandie; Wu, Pei-Hsuan; Tarr, Paul T; Lindenberg, Katrin S; St-Pierre, Julie; Zhang, Chen-Yu; Mootha, Vamsi K; Jäger, Sibylle; Vianna, Claudia R; Reznick, Richard M; Cui, Libin; Manieri, Monia; Donovan, Mi X; Wu, Zhidan; Cooper, Marcus P; Fan, Melina C; Rohas, Lindsay M; Zavacki, Ann Marie; Cinti, Saverio; Shulman, Gerald I; Lowell, Bradford B; Krainc, Dimitri; Spiegelman, Bruce M

2004-10-01

PGC-1alpha is a coactivator of nuclear receptors and other transcription factors that regulates several metabolic processes, including mitochondrial biogenesis and respiration, hepatic gluconeogenesis, and muscle fiber-type switching. We show here that, while hepatocytes lacking PGC-1alpha are defective in the program of hormone-stimulated gluconeogenesis, the mice have constitutively activated gluconeogenic gene expression that is completely insensitive to normal feeding controls. C/EBPbeta is elevated in the livers of these mice and activates the gluconeogenic genes in a PGC-1alpha-independent manner. Despite having reduced mitochondrial function, PGC-1alpha null mice are paradoxically lean and resistant to diet-induced obesity. This is largely due to a profound hyperactivity displayed by the null animals and is associated with lesions in the striatal region of the brain that controls movement. These data illustrate a central role for PGC-1alpha in the control of energy metabolism but also reveal novel systemic compensatory mechanisms and pathogenic effects of impaired energy homeostasis.

Rolling Process Modeling Report: Finite-Element Prediction of Roll Separating Force and Rolling Defects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Lavender, Curt A.; Paxton, Dean M.

2014-04-23

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum (U-10Mo) alloy plate-type fuel for the U.S. high-performance research reactors. This work supports the Convert Program of the U.S. Department of Energy’s National Nuclear Security Administration (DOE/NNSA) Global Threat Reduction Initiative. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll separating forces and rolling defects. Simulations were performed using a finite-element model developed using the commercial code LS-Dyna. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel have been conducted following two different schedules. Model predictions ofmore » the roll-separation force and roll-pack thicknesses at different stages of the rolling process were compared with experimental measurements. This report discusses various attributes of the rolled coupons revealed by the model (e.g., dog-boning and thickness non-uniformity).« less

Evaluation of New Repair Methods for Seal Surface Defects on Reusable Solid Rocket Motor (RSRM) Hardware

NASA Technical Reports Server (NTRS)

Stanley, Stephanie; Selvidge, Shawn

2003-01-01

The focus of the evaluation was to develop a back-up method to cell plating for the improvement or repair of seal surface defects within D6-AC steel and 7075-T73 aluminum used in the RSRM program. Several techniques were investigated including thermal and non-thermal based techniques. Ideally the repair would maintain the inherent properties of the substrate without losing integrity at the repair site. The repaired sites were tested for adhesion, corrosion, hardness, microhardness, surface toughness, thermal stability, ability to withstand bending of the repair site, and the ability to endure a high-pressure water blast without compromising the repaired site. The repaired material could not change the inherent properties of the substrate throughout each of the test in order to remain a possible technique to repair the RSRM substrate materials. One repair method, Electro-Spark Alloying, passed all the testing and is considered a candidate for further evaluation.

Evaluation of New Repair Methods for Seal Surface Defects on Reusable Solid Rocket Motor (RSRM) Hardware

NASA Technical Reports Server (NTRS)

Stanley, Stephanie D.; Selvidge, Shawn A.; Cash, Steve (Technical Monitor)

2002-01-01

The focus of the evaluation was to develop a back-up method to cell plating for the improvement or repair of seal surface defects within D6-AC steel and 7075-T73 aluminum used in the RSRM program. Several techniques were investigated including thermal and non-thermal based techniques. Ideally the repair would maintain the inherent properties of the substrate without losing integrity at the repair site. The repaired sites were tested for adhesion, corrosion, hardness, microhardness, surface toughness, thermal stability, ability to withstand bending of the repair site, and the ability to endure a high-pressure water blast without compromising the repaired site. The repaired material could not change the inherent properties of the substrate throughout each of the test in order to remain a possible technique to repair the RSRM substrate materials. One repair method, Electro-Spark Alloying, passed all the testing and is considered a candidate for further evaluation.

Switching of metabolic programs in response to light availability is an essential function of the cyanobacterial circadian output pathway

PubMed Central

Puszynska, Anna M; O'Shea, Erin K

2017-01-01

The transcription factor RpaA is the master regulator of circadian transcription in cyanobacteria, driving genome-wide oscillations in mRNA abundance. Deletion of rpaA has no effect on viability in constant light conditions, but renders cells inviable in cycling conditions when light and dark periods alternate. We investigated the mechanisms underlying this viability defect, and demonstrate that the rpaA- strain cannot maintain appropriate energy status at night, does not accumulate carbon reserves during the day, and is defective in transcription of genes crucial for utilization of carbohydrate stores at night. Reconstruction of carbon utilization pathways combined with provision of an external carbon source restores energy charge and viability of the rpaA- strain in light/dark cycling conditions. Our observations highlight how a circadian output pathway controls and temporally coordinates essential pathways in carbon metabolism to maximize fitness of cells facing periodic energy limitations. DOI: http://dx.doi.org/10.7554/eLife.23210.001 PMID:28430105

Elastic plastic fracture mechanics methodology for surface cracks

NASA Astrophysics Data System (ADS)

Ernst, Hugo A.; Boatwright, D. W.; Curtin, W. J.; Lambert, D. M.

1993-08-01

The Elastic Plastic Fracture Mechanics (EPFM) Methodology has evolved significantly in the last several years. Nevertheless, some of these concepts need to be extended further before the whole methodology can be safely applied to structural parts. Specifically, there is a need to include the effect of constraint in the characterization of material resistance to crack growth and also to extend these methods to the case of 3D defects. As a consequence, this project was started as a 36 month research program with the general objective of developing an EPFM methodology to assess the structural reliability of pressure vessels and other parts of interest to NASA containing defects. This report covers a computer modelling algorithm used to simulate the growth of a semi-elliptical surface crack; the presentation of a finite element investigation that compared the theoretical (HRR) stress field to that produced by elastic and elastic-plastic models; and experimental efforts to characterize three dimensional aspects of fracture present in 'two dimensional', or planar configuration specimens.

Combined Molecular and Spin Dynamics Simulation of Lattice Vacancies in BCC Iron

NASA Astrophysics Data System (ADS)

Mudrick, Mark; Perera, Dilina; Eisenbach, Markus; Landau, David P.

Using an atomistic model that treats translational and spin degrees of freedom equally, combined molecular and spin dynamics simulations have been performed to study dynamic properties of BCC iron at varying levels of defect impurity. Atomic interactions are described by an empirical many-body potential, and spin interactions with a Heisenberg-like Hamiltonian with a coordinate dependent exchange interaction. Equations of motion are solved numerically using the second-order Suzuki-Trotter decomposition for the time evolution operator. We analyze the spatial and temporal correlation functions for atomic displacements and magnetic order to obtain the effect of vacancy defects on the phonon and magnon excitations. We show that vacancy clusters in the material cause splitting of the characteristic transverse spin-wave excitations, indicating the production of additional excitation modes. Additionally, we investigate the coupling of the atomic and magnetic modes. These modes become more distinct with increasing vacancy cluster size. This material is based upon work supported by the U.S. Department of Energy Office of Science Graduate Student Research (SCGSR) program.

RIPK4 phosphorylates Dishevelled proteins to regulate canonical Wnt signaling

PubMed Central

Huang, XiaoDong; McGann, James C.; Liu, Bob Y.; Hannoush, Rami N.; Lill, Jennie R.; Pham, Victoria; Newton, Kim; Kakunda, Michael; Liu, Jinfeng; Yu, Christine; Hymowitz, Sarah G.; Hongo, Jo-Anne; Wynshaw-Boris, Anthony; Polakis, Paul; Harland, Richard M.; Dixit, Vishva M.

2014-01-01

Receptor interacting protein kinase 4 (RIPK4) is required for epidermal differentiation (1–4) and is mutated in Bartsocas-Papas syndrome (5, 6). While RIPK4 binds protein kinase C (5, 6), RIPK4 signaling mechanisms are largely unknown. We show that ectopic RIPK4 induces cytosolic β-catenin accumulation and a transcriptional program similar to Wnt3a, whereas kinase-defective or Bartsocas-Papas syndrome RIPK4 mutants do not. Ectopic ripk4 synergized with Wnt family member xwnt8 in Xenopus, whereas ripk4 morpholinos or kinase-defective RIPK4 antagonized Wnt signaling. Mechanistically, RIKP4 interacted constitutively with the Wnt adaptor protein DVL2 and, after Wnt3a stimulation, with the co-receptor LRP6. Phosphorylation of DVL2 at Ser298 and Ser480 by RIPK4 favored canonical Wnt signaling. Growth of a Wnt-dependent N-Tera2 xenograft tumor model was suppressed by RIPK4 knockdown, suggesting that RIPK4 overexpression may contribute to the growth of certain tumor types. PMID:23371553

Localization and roles of Ski8p protein in Sordaria meiosis and delineation of three mechanistically distinct steps of meiotic homolog juxtaposition.

PubMed

Tessé, Sophie; Storlazzi, Aurora; Kleckner, Nancy; Gargano, Silvana; Zickler, Denise

2003-10-28

Ski8p is implicated in degradation of non-poly(A) and double-stranded RNA, and in meiotic DNA recombination. We have identified the Sordaria macrospora SKI8 gene. Ski8p is cytoplasmically localized in all vegetative and sexual cycle cells, and is nuclear localized, specifically in early-mid-meiotic prophase, in temporal correlation with Spo11p, the meiotic double-strand break (DSB) transesterase. Localizations of Ski8p and Spo11p are mutually interdependent. ski8 mutants exhibit defects in vegetative growth, entry into the sexual program, and sporulation. Diverse meiotic defects, also seen in spo11 mutants, are diagnostic of DSB absence, and they are restored by exogenous DSBs. These results suggest that Ski8p promotes meiotic DSB formation by acting directly within meiotic prophase chromosomes. Mutant phenotypes also divide meiotic homolog juxtaposition into three successive, mechanistically distinct steps; recognition, presynaptic alignment, and synapsis, which are distinguished by their differential dependence on DSBs.

Localization and roles of Ski8p protein in Sordaria meiosis and delineation of three mechanistically distinct steps of meiotic homolog juxtaposition

PubMed Central

Tessé, Sophie; Storlazzi, Aurora; Kleckner, Nancy; Gargano, Silvana; Zickler, Denise

2003-01-01

Ski8p is implicated in degradation of non-poly(A) and double-stranded RNA, and in meiotic DNA recombination. We have identified the Sordaria macrospora SKI8 gene. Ski8p is cytoplasmically localized in all vegetative and sexual cycle cells, and is nuclear localized, specifically in early-mid-meiotic prophase, in temporal correlation with Spo11p, the meiotic double-strand break (DSB) transesterase. Localizations of Ski8p and Spo11p are mutually interdependent. ski8 mutants exhibit defects in vegetative growth, entry into the sexual program, and sporulation. Diverse meiotic defects, also seen in spo11 mutants, are diagnostic of DSB absence, and they are restored by exogenous DSBs. These results suggest that Ski8p promotes meiotic DSB formation by acting directly within meiotic prophase chromosomes. Mutant phenotypes also divide meiotic homolog juxtaposition into three successive, mechanistically distinct steps; recognition, presynaptic alignment, and synapsis, which are distinguished by their differential dependence on DSBs. PMID:14563920

Elastic plastic fracture mechanics methodology for surface cracks

NASA Technical Reports Server (NTRS)

Ernst, Hugo A.; Boatwright, D. W.; Curtin, W. J.; Lambert, D. M.

1993-01-01

The Elastic Plastic Fracture Mechanics (EPFM) Methodology has evolved significantly in the last several years. Nevertheless, some of these concepts need to be extended further before the whole methodology can be safely applied to structural parts. Specifically, there is a need to include the effect of constraint in the characterization of material resistance to crack growth and also to extend these methods to the case of 3D defects. As a consequence, this project was started as a 36 month research program with the general objective of developing an EPFM methodology to assess the structural reliability of pressure vessels and other parts of interest to NASA containing defects. This report covers a computer modelling algorithm used to simulate the growth of a semi-elliptical surface crack; the presentation of a finite element investigation that compared the theoretical (HRR) stress field to that produced by elastic and elastic-plastic models; and experimental efforts to characterize three dimensional aspects of fracture present in 'two dimensional', or planar configuration specimens.

aPKCλ/ι and aPKCζ Contribute to Podocyte Differentiation and Glomerular Maturation

PubMed Central

Hartleben, Björn; Widmeier, Eugen; Suhm, Martina; Worthmann, Kirstin; Schell, Christoph; Helmstädter, Martin; Wiech, Thorsten; Walz, Gerd; Leitges, Michael; Schiffer, Mario

2013-01-01

Precise positioning of the highly complex interdigitating podocyte foot processes is critical to form the normal glomerular filtration barrier, but the molecular programs driving this process are unknown. The protein atypical protein kinase C (aPKC)—a component of the Par complex, which localizes to tight junctions and interacts with slit diaphragm proteins—may play a role. Here, we found that the combined deletion of the aPKCλ/ι and aPKCζ isoforms in podocytes associated with incorrectly positioned centrosomes and Golgi apparatus and mislocalized molecules of the slit diaphragm. Furthermore, aPKC-deficient podocytes failed to form the normal network of foot processes, leading to defective glomerular maturation with incomplete capillary formation and mesangiolysis. Our results suggest that aPKC isoforms orchestrate the formation of the podocyte processes essential for normal glomerular development and kidney function. Defective aPKC signaling results in a dramatically simplified glomerular architecture, causing severe proteinuria and perinatal death. PMID:23334392

YAP is essential for mechanical force production and epithelial cell proliferation during lung branching morphogenesis

PubMed Central

Lin, Chuwen; Yao, Erica; Zhang, Kuan; Jiang, Xuan; Croll, Stacey; Thompson-Peer, Katherine; Chuang, Pao-Tien

2017-01-01

Branching morphogenesis is a fundamental program for tissue patterning. We show that active YAP, a key mediator of Hippo signaling, is distributed throughout the murine lung epithelium and loss of epithelial YAP severely disrupts branching. Failure to branch is restricted to regions where YAP activity is removed. This suggests that YAP controls local epithelial cell properties. In support of this model, mechanical force production is compromised and cell proliferation is reduced in Yap mutant lungs. We propose that defective force generation and insufficient epithelial cell number underlie the branching defects. Through genomic analysis, we also uncovered a feedback control of pMLC levels, which is critical for mechanical force production, likely through the direct induction of multiple regulators by YAP. Our work provides a molecular pathway that could control epithelial cell properties required for proper morphogenetic movement and pattern formation. DOI: http://dx.doi.org/10.7554/eLife.21130.001 PMID:28323616

Assessment of NDE reliability data

NASA Technical Reports Server (NTRS)

Yee, B. G. W.; Couchman, J. C.; Chang, F. H.; Packman, D. F.

1975-01-01

Twenty sets of relevant nondestructive test (NDT) reliability data were identified, collected, compiled, and categorized. A criterion for the selection of data for statistical analysis considerations was formulated, and a model to grade the quality and validity of the data sets was developed. Data input formats, which record the pertinent parameters of the defect/specimen and inspection procedures, were formulated for each NDE method. A comprehensive computer program was written and debugged to calculate the probability of flaw detection at several confidence limits by the binomial distribution. This program also selects the desired data sets for pooling and tests the statistical pooling criteria before calculating the composite detection reliability. An example of the calculated reliability of crack detection in bolt holes by an automatic eddy current method is presented.

The Potential of Sonic IR to Inspect Aircraft Components Traditionally Inspected with Fluorescent Penetrant and or Magnetic Particle Inspection

NASA Astrophysics Data System (ADS)

DiMambro, J.; Ashbaugh, D. M.; Han, X.; Favro, L. D.; Lu, J.; Zeng, Z.; Li, W.; Newaz, G. M.; Thomas, R. L.

2006-03-01

Sandia National Laboratories Airworthiness Assurance Nondestructive Inspection Validation Center (AANC) provides independent and quantitative evaluations of new and enhanced inspection, to developers, users, and regulators of aircraft. Wayne State University (WSU) has developed and patented an inspection technique using high-power ultrasonic excitation and infrared technology to detect defects in a variety of materials. AANC and WSU are working together as part of the FAA Sonic Infrared Technology Transfer Program. The ultimate goal of the program is to implement Sonic IR in the aviation field where appropriate. The capability of Sonic IR imaging to detect cracks in components commonly inspected with magnetic particle or liquid penetrant inspection in the field is of interest to industry.

Transition mechanism of Stone-Wales defect in armchair edge (5,5) carbon nanotube

NASA Astrophysics Data System (ADS)

Setiadi, Agung; Suprijadi

2015-04-01

We performed first principles calculations of Stone-Wales (SW) defects in armchair edge (5,5) carbon nanotube (CNT) by the density functional theory (DFT). Stone Wales (SW) defect is one kind of topological defect on the CNT. There are two kind of SW defect on the armchair edge (5,5) CNT, such as longitudinal and circumference SW defect. Barrier energy in the formation of SW defects is a good consideration to become one of parameter in controlling SW defects on the CNT. Our calculation results that a longitudinal SW defect is more stable than circumference SW defect. However, the barrier energy of circumference SW defect is lower than another one. We applied Climbing Image Nudge Elastic Band (CI-NEB) method to find minimum energy path (MEP) and barrier energy for SW defect transitions. We also found that in the case of circumference SW defect, armchair edge (5,5) CNT become semiconductor with the band gap of 0.0544 eV.

Investigation of defect modes in a defective photonic crystal with a semiconductor metamaterial defect

NASA Astrophysics Data System (ADS)

Wu, Meng-Ru; Wu, Chien-Jang; Chang, Shoou-Jinn

2014-11-01

In this work, we theoretically investigate the properties of defect modes in a defective photonic crystal containing a semiconductor metamaterial defect. We consider the structure, (LH)N/DP/(LH)N, where N and P are respectively the stack numbers, L is SiO2, H is InP, and defect layer D is a semiconductor metamaterial composed of Al-doped ZnO (AZO) and ZnO. It is found that, within the photonic band gap, the number of defect modes (transmission peaks) will decrease as the defect thickness increases, in sharp contrast to the case of using usual dielectric defect. The peak height and position can be changed by the variation in the thickness of defect layer. In the angle-dependent defect mode, its position is shown to be blue-shifted as the angle of incidence increases for both TE and TM waves. The analysis of defect mode provides useful information for the design of tunable transmission filter in semiconductor optoelectronics.

Effects of Stone-Wales and vacancy defects in atomic-scale friction on defective graphite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xiao-Yu; Key Laboratory of Hubei Province for Water Jet Theory and New Technology, Wuhan University, Wuhan 430072; Wu, RunNi

2014-05-05

Graphite is an excellent solid lubricant for surface coating, but its performance is significantly weakened by the vacancy or Stone-Wales (SW) defect. This study uses molecular dynamics simulations to explore the frictional behavior of a diamond tip sliding over a graphite which contains a single defect or stacked defects. Our results suggest that the friction on defective graphite shows a strong dependence on defect location and type. The 5-7-7-5 structure of SW defect results in an effectively negative slope of friction. For defective graphite containing a defect in the surface, adding a single vacancy in the interior layer will decreasemore » the friction coefficients, while setting a SW defect in the interior layer may increase the friction coefficients. Our obtained results may provide useful information for understanding the atomic-scale friction properties of defective graphite.« less

7 CFR 42.106 - Classifying and recording defects.

Code of Federal Regulations, 2013 CFR

2013-01-01

... container is scored only once for these two defects since the rust condition can be atributed to the leak... “leaker” (a critical defect) and not as “pitted rust” (a major defect). (2) Unrelated defects are defects...

7 CFR 42.106 - Classifying and recording defects.

Code of Federal Regulations, 2014 CFR

2014-01-01

... container is scored only once for these two defects since the rust condition can be attributed to the leak... “leaker” (a critical defect) and not as “pitted rust” (a major defect). (2) Unrelated defects are defects...

7 CFR 42.106 - Classifying and recording defects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... container is scored only once for these two defects since the rust condition can be atributed to the leak... “leaker” (a critical defect) and not as “pitted rust” (a major defect). (2) Unrelated defects are defects...

7 CFR 42.106 - Classifying and recording defects.

Code of Federal Regulations, 2012 CFR

2012-01-01

... container is scored only once for these two defects since the rust condition can be atributed to the leak... “leaker” (a critical defect) and not as “pitted rust” (a major defect). (2) Unrelated defects are defects...

7 CFR 42.106 - Classifying and recording defects.

Code of Federal Regulations, 2010 CFR

2010-01-01

... container is scored only once for these two defects since the rust condition can be atributed to the leak... “leaker” (a critical defect) and not as “pitted rust” (a major defect). (2) Unrelated defects are defects...

Proceedings of the 20th International Conference on Defects in Semiconductors Held in Berkeley, CA, USA, 26-30 July 1999

DTIC Science & Technology

1999-07-30

National Science Foundation through the GOALI Program, under grant number ECS-9705134. References [1] T. Ogino, M. Aoki, Jap. J. Appl. Phys. 19 (1980... pulled from molten silicon through a graphite slot for solar cell production in economical way [8]. It was observed that EFG silicon contains high...samples the closest resem- blance to our observations is found in the Au-Hj config- uration where the --/- gold acceptor level is pulled down in the

HgCdTe Surface and Defect Study Program.

DTIC Science & Technology

1985-01-01

LWIR (x 0.2) HgCdTe surface will be so depleted in cations that the resulting equivajqnt alloy will be metallic or semimetallic (x < 0.17), and hence...spectrometry (PES) results on MWIR are applicable to the first 10 to 15A of the surface. The point here is that LWIR material may respond to passivation...processes to produce a fundamentally different result than does MWIR material, and LWIR should in fact be treated as a completely different material. These

A Study to Develop a Methodology Determining the Feasibility of Establishing a Blood Collection Program in an Army Healthcare Facility

DTIC Science & Technology

1985-05-01

minimal. The risk of acquiring syphilis through blood transfusions is so rare that American Association of Blood Bank Standards have dropped the...requirement to test for syphilis , although Federal regulations still require it. Malaria can be effectively screened out by excluding potential donors. 2 9 The...murmur or repair of a congenital defect medical director. Listed below are some does not necessarily disqualify a donor. drugs and medical conditions

Evaluation program for secondary spacecraft cells: Acceptance test of McDonnell-Douglas, Astropower division, 40.0 ampere hour silver-zinc cells

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1971-01-01

The development of an inorganic separator material for use in construction of 40 ampere-hour silver zinc cells is discussed. Acceptance tests were conducted to determine real quality, physical defects and ampere-hour capacity. All acceptance tests were performed at an ambient temperature of 23 to 27 C at existing relative humidity and atmospheric pressure. Of the 63 cells tested, only one failed to meet the equipment specifications.

An Analysis of Communication Between Program Managers and Contracting Officers and Its Effect on the Performance of the Defense Acquisition System

DTIC Science & Technology

2015-09-01

problem or defect must first be present. The qualitative interview data along with reduction and analysis provided the bulk of this research . The...problem and to provide grounds for the purpose of this research . Common themes extracted from interview data will comprise the qualitative data set...communication, we used mixed methods’ research to examine current statistics and to conduct in-person interviews . With this research , we found a link

Progress Report for the Joint Services Electronic Program for the Period April 1, 1989 through March 31, 1990 (Coordinated Science Laboratory, University of Illinois at Urbana-Champaign)

DTIC Science & Technology

1990-06-30

since the projected ion range is of the order of lattice constants. Thus, we have extended our thermal-dopant incorporation model and have developed...bombardment results in residual lattice damage, which degrades electrical and optical properties. Obviously, at sufficiently high acceleration energies...understand the details of collisional lattice dynamics and ion-induced defect for- mation and annihilation. In addition, the simulations are providing, for

Improved Healing of Large, Osseous, Segmental Defects by Reverse Dynamization: Evaluation in a Sheep Model

DTIC Science & Technology

2015-10-01

practical examination of current methods,” J. Biomech., Oct. 2015. [8] R. J. Nesbitt, S . T. Herfat, D. V. Boguszewski, A . J. Engel, M . T. Galloway, and J... a Sheep Model 5b. GRANT NUMBER W81XWH-13-1-0324 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) Christopher H. Evans, Ph.D. 5d. PROJECT NUMBER...interfragmentary movement ( IFM ) through the separated bone cortices (fracture gap). In research funded by a CDMRP Idea Development Award, we used a

[Twenty-five years of screening eugenics in Spain].

PubMed

Mérida Donoso, Salvador

2012-01-01

Over the past 25 years, the incidence of newborns with congenital defects in Spain has fallen by 56.7% primarily due to the practice of "fetal risk" abortion, after prenatal diagnosis. In some cases, such as people with Down syndrome, the strategy involves the removal of 80-90% of those affected in pregnancy. After presenting the techniques used today and statistical data, we will make a reflection about the ethical justification for prenatal diagnosis programs and practice of "eugenic" abortion.

Technology Infusion of CodeSonar into the Space Network Ground Segment

NASA Technical Reports Server (NTRS)

Benson, Markland J.

2009-01-01

This slide presentation reviews the applicability of CodeSonar to the Space Network software. CodeSonar is a commercial off the shelf system that analyzes programs written in C, C++ or Ada for defects in the code. Software engineers use CodeSonar results as an input to the existing source code inspection process. The study is focused on large scale software developed using formal processes. The systems studied are mission critical in nature but some use commodity computer systems.

Borescope Inspection Management for Engine

NASA Astrophysics Data System (ADS)

Zhongda, Yuan

2018-03-01

In this paper, we try to explain the problems need to be improved from the two perspectives of maintenance program management and maintenance human risk control. On the basis of optimization analysis of borescope inspection maintenance scheme, the defect characteristics and expansion rules of engine heat terminal components are summarized, and some optimization measures are introduced. This paper analyses human risk problem of engine hole from the aspects of qualification management, training requirements and perfection of system, and puts forward some suggestions on management.

Fatigue flaw growth and NDI evaluation for preventing through cracks in spacecraft tankage structures

NASA Technical Reports Server (NTRS)

Pettit, D. E.; Hoeppner, D. W.

1972-01-01

A program was conducted to determine the fatigue-crack propagation behavior of parent and welded 2219-T87 aluminum alloy sheet under controlled cyclic stress conditions in room temperature air and 300 F air. Specimens possessing an initial surface defect of controlled dimensions were cycled under constant load amplitude until the propagating fatigue crack penetrated the back surface of the specimen. A series of precracked specimens were prepared to determine optimum penetrant, X-ray, ultrasonic, and eddy current nondestructive inspection procedures.

Atomically Flat Surfaces Developed for Improved Semiconductor Devices

NASA Technical Reports Server (NTRS)

Powell, J. Anthony

2001-01-01

New wide bandgap semiconductor materials are being developed to meet the diverse high temperature, -power, and -frequency demands of the aerospace industry. Two of the most promising emerging materials are silicon carbide (SiC) for high-temperature and high power applications and gallium nitride (GaN) for high-frequency and optical (blue-light-emitting diodes and lasers) applications. This past year Glenn scientists implemented a NASA-patented crystal growth process for producing arrays of device-size mesas whose tops are atomically flat (i.e., step-free). It is expected that these mesas can be used for fabricating SiC and GaN devices with major improvements in performance and lifetime. The promising new SiC and GaN devices are fabricated in thin-crystal films (known as epi films) that are grown on commercial single-crystal SiC wafers. At this time, no commercial GaN wafers exist. Crystal defects, known as screw defects and micropipes, that are present in the commercial SiC wafers propagate into the epi films and degrade the performance and lifetime of subsequently fabricated devices. The new technology isolates the screw defects in a small percentage of small device-size mesas on the surface of commercial SiC wafers. This enables atomically flat surfaces to be grown on the remaining defect-free mesas. We believe that the atomically flat mesas can also be used to grow GaN epi films with a much lower defect density than in the GaN epi films currently being grown. Much improved devices are expected from these improved low-defect epi films. Surface-sensitive SiC devices such as Schottky diodes and field effect transistors should benefit from atomically flat substrates. Also, we believe that the atomically flat SiC surface will be an ideal surface on which to fabricate nanoscale sensors and devices. The process for achieving atomically flat surfaces is illustrated. The surface steps present on the "as-received" commercial SiC wafer is also illustrated. because of the small tilt angle between the crystal "basal" plane and the polished wafer surface. These steps are used in normal SiC epi film growth in a process known as stepflow growth to produce material for device fabrication. In the new process, the first step is to etch an array of mesas on the SiC wafer top surface. Then, epi film growth is carried out in the step flow fashion until all steps have grown themselves out of existence on each defect-free mesa. If the size of the mesas is sufficiently small (about 0.1 by 0.1 mm), then only a small percentage of the mesas will contain an undesired screw defect. Mesas with screw defects supply steps during the growth process, allowing a rough surface with unwanted hillocks to form on the mesa. The improvement in SiC epi surface morphology achievable with the new technology is shown. An atomic force microscope image of a typical SiC commercial epilayer surface is also shown. A similar image of an SiC atomically flat epi surface grown in a Glenn laboratory is given. With the current screw defect density of commercial wafers (about 5000 defects/cm2), the yield of atomically free 0.1 by 0.l mm mesas is expected to be about 90 percent. This is large enough for many types of electronic and optical devices. The implementation of this new technology was recently published in Applied Physics Letters. This work was initially carried out in-house under a Director's Discretionary Fund project and is currently being further developed under the Information Technology Base Program.

Defect reaction network in Si-doped InAs. Numerical predictions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, Peter A.

This Report characterizes the defects in the def ect reaction network in silicon - doped, n - type InAs predicted with first principles density functional theory. The reaction network is deduced by following exothermic defect reactions starting with the initially mobile interstitial defects reacting with common displacement damage defects in Si - doped InAs , until culminating in immobile reaction p roducts. The defect reactions and reaction energies are tabulated, along with the properties of all the silicon - related defects in the reaction network. This Report serves to extend the results for the properties of intrinsic defects in bulkmore » InAs as colla ted in SAND 2013 - 2477 : Simple intrinsic defects in InAs : Numerical predictions to include Si - containing simple defects likely to be present in a radiation - induced defect reaction sequence . This page intentionally left blank« less