45 CFR 63.2 - Eligibility for award.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and qualified by educational, scientific, or other relevant competence to carry out a proposed project... part. (b) Project eligible—(1) Policy Research. Any project found by the Assistant Secretary to be a research, pilot, evaluation, or demonstration project within the meaning of this section and § 63.1 shall...

42 CFR 495.306 - Establishing patient volume.

Code of Federal Regulations, 2011 CFR

2011-10-01

... encounter means services rendered to an individual on any one day where— (i) Medicaid or CHIP (or a Medicaid or CHIP demonstration project approved under section 1115 of the Act) paid for part or all of the service; (ii) Medicaid or CHIP (or a Medicaid or CHIP demonstration project approved under section 1115 of...

34 CFR 350.62 - What are the matching requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements? (a)(1) The Secretary may make grants to pay for part of the costs of research and demonstration... projects. (2) Each grantee must participate in the costs of those projects. (3) The specific amount of cost... considered in the selection process. (b)(1) The Secretary may make grants to pay for part or all of the costs...

Community Based Demonstration Projects: Willamette Ecosystem Services Project (WESP)

EPA Science Inventory

EPA’s Ecosystem Services Research Program in the Office of Research and Development is focused on the study of ecosystem services and the benefits to human well-being provided by ecological systems. As part of this research effort, the Willamette Ecosystems Services Project (WE...

34 CFR 400.2 - What programs are governed by these regulations?

Code of Federal Regulations, 2013 CFR

2013-07-01

...). (8) National Network for Curriculum Coordination in Vocational and Technical Education (34 CFR part... Projects for the Integration of Vocational and Academic Learning Program (34 CFR part 425). (21) Cooperative Demonstration Programs (34 CFR part 426). (22) Bilingual Vocational Training Program (34 CFR part...

34 CFR 400.2 - What programs are governed by these regulations?

Code of Federal Regulations, 2014 CFR

2014-07-01

...). (8) National Network for Curriculum Coordination in Vocational and Technical Education (34 CFR part... Projects for the Integration of Vocational and Academic Learning Program (34 CFR part 425). (21) Cooperative Demonstration Programs (34 CFR part 426). (22) Bilingual Vocational Training Program (34 CFR part...

34 CFR 400.2 - What programs are governed by these regulations?

Code of Federal Regulations, 2012 CFR

2012-07-01

...). (8) National Network for Curriculum Coordination in Vocational and Technical Education (34 CFR part... Projects for the Integration of Vocational and Academic Learning Program (34 CFR part 425). (21) Cooperative Demonstration Programs (34 CFR part 426). (22) Bilingual Vocational Training Program (34 CFR part...

The EMCC / DARPA Massively Parallel Electromagnetic Scattering Project

NASA Technical Reports Server (NTRS)

Woo, Alex C.; Hill, Kueichien C.

1996-01-01

The Electromagnetic Code Consortium (EMCC) was sponsored by the Advanced Research Program Agency (ARPA) to demonstrate the effectiveness of massively parallel computing in large scale radar signature predictions. The EMCC/ARPA project consisted of three parts.

Ground penetrating radar evaluation of new pavement density.

DOT National Transportation Integrated Search

2015-02-01

The objective of this project was to map pavement surface density variations using dielectric : measurements from ground penetrating radar (GPR). The work was carried out as part of an : Asphalt Intelligent Compaction demonstration project on SR 539 ...

Demonstrating artificial intelligence for space systems - Integration and project management issues

NASA Technical Reports Server (NTRS)

Hack, Edmund C.; Difilippo, Denise M.

1990-01-01

As part of its Systems Autonomy Demonstration Project (SADP), NASA has recently demonstrated the Thermal Expert System (TEXSYS). Advanced real-time expert system and human interface technology was successfully developed and integrated with conventional controllers of prototype space hardware to provide intelligent fault detection, isolation, and recovery capability. Many specialized skills were required, and responsibility for the various phases of the project therefore spanned multiple NASA centers, internal departments and contractor organizations. The test environment required communication among many types of hardware and software as well as between many people. The integration, testing, and configuration management tools and methodologies which were applied to the TEXSYS project to assure its safe and successful completion are detailed. The project demonstrated that artificial intelligence technology, including model-based reasoning, is capable of the monitoring and control of a large, complex system in real time.

IDC Reengineering Iteration I2 Architectural Prototype Reports

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamlet, Benjamin R.

To fulfill the inception phase deliverable “Demonstration of architectural prototype“ the SNL IDC Reengineering project team is providing seven reports describing system prototyping work completed between October 2012 and October 2014as part of the SNL US NDC Modernization project.

American Fuel Cell Bus Project Evaluation : Second Report

DOT National Transportation Integrated Search

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses (FCEB) operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Admini...

United States-European Commission Urban Freight Twinning Initiative: Compendium of Project Summaries

DOT National Transportation Integrated Search

2017-09-01

This compendium is comprised of 33 brief summaries of urban freight initiatives that include research projects, plans, pilot demonstrations, and other efforts. These initiatives were presented at a roundtable discussion that was part of the 2017 Annu...

Prisons and Primary Schools: Using CHAT to Analyse the Relationship between Developing Identity, Developing Musicianship and Transformative Processes

ERIC Educational Resources Information Center

Henley, Jennie

2015-01-01

This paper draws on three different research projects to demonstrate the use of an expanded model of Cultural Historical Activity Theory (CHAT), developed as part of a doctoral research study. The first project is an evaluation of the impacts of a Music Partnership Project within Primary and Secondary schools. The second project is an evaluation…

Grid-Scale Energy Storage Demonstration of Ancillary Services Using the UltraBattery Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seasholtz, Jeff

2015-08-20

The collaboration described in this document is being done as part of a cooperative research agreement under the Department of Energy’s Smart Grid Demonstration Program. This document represents the Final Technical Performance Report, from July 2012 through April 2015, for the East Penn Manufacturing Smart Grid Program demonstration project. This Smart Grid Demonstration project demonstrates Distributed Energy Storage for Grid Support, in particular the economic and technical viability of a grid-scale, advanced energy storage system using UltraBattery ® technology for frequency regulation ancillary services and demand management services. This project entailed the construction of a dedicated facility on the Eastmore » Penn campus in Lyon Station, PA that is being used as a working demonstration to provide regulation ancillary services to PJM and demand management services to Metropolitan Edison (Met-Ed).« less

Professor's Page: Do Demonstration Lessons Work?

ERIC Educational Resources Information Center

Clarke, Doug

2011-01-01

As part of a large research and professional development project funded by the Catholic Education Office Melbourne (CEOM), called "Contemporary Teaching and Learning of Mathematics," the ACU team has been leading demonstration lessons. There is certainly not universal agreement on the worth of demonstration lessons in the mathematics…

Research notes : solar powered navigational lighting system demonstration project.

DOT National Transportation Integrated Search

2011-04-01

ODOT will be installing a solar powered navigational lighting system on the AstoriaMegler Bridge as part of a pilot project approved by the Federal Highways Administration (FHWA). The coastal bridge is the connection across the Columbia River on U.S....

A Proposal to Build an Education Research and Development Program: The Kamehameha Early Education Project Proposal. Technical Report #3.

ERIC Educational Resources Information Center

Gallimore, Ronald; And Others

This report summarizes the programmatic features of a proposal for the Kamehameha Early Education Project (KEEP), a program aimed at the development, demonstration, and dissemination of methods for improving the education of Hawaiian and part-Hawaiian children. A brief description of the proposed project goals, structure, organization, and…

Experimental Demonstration of Technologies for Autonomous On-Orbit Robotic Assembly

NASA Technical Reports Server (NTRS)

LeMaster, Edward A.; Schaechter, David B.; Carrington, Connie K.

2006-01-01

The Modular Reconfigurable High Energy (MRHE) program aimed to develop technologies for the automated assembly and deployment of large-scale space structures and aggregate spacecraft. Part of the project involved creation of a terrestrial robotic testbed for validation and demonstration of these technologies and for the support of future development activities. This testbed was completed in 2005, and was thereafter used to demonstrate automated rendezvous, docking, and self-assembly tasks between a group of three modular robotic spacecraft emulators. This paper discusses the rationale for the MRHE project, describes the testbed capabilities, and presents the MRHE assembly demonstration sequence.

Educational Voucher Demonstration Archive: Project-Level Documentation.

ERIC Educational Resources Information Center

Leinwand (C.M.) Associates, Inc., Newton, MA.

This report describes the Educational Voucher Demonstration, serves as a guide for its documentation, and offers an extensive bibliography. Part 1 gives background information and summarizes the implementation of the Alum Rock Demonstration based on a transitional voucher model and involving six public schools, each offering at least two distinct…

Alaska road weather project : technical performance assessment report Fairbanks field demonstration 2013-2014.

DOT National Transportation Integrated Search

2014-02-01

The Alaska Department of Transportation and Public Facilities began implementation of a Maintenance Decision Support System in an : effort to improve snow and ice control in the Fairbanks area. As part of the project the reliability of the weather fo...

Energy savings in Polish buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Markel, L.C.; Gula, A.; Reeves, G.

1995-12-31

A demonstration of low-cost insulation and weatherization techniques was a part of phase 1 of the Krakow Clean Fossil Fuels and Energy Efficient Project. The objectives were to identify a cost-effective set of measures to reduce energy used for space heating, determine how much energy could be saved, and foster widespread implementation of those measures. The demonstration project focused on 4 11-story buildings in a Krakow housing cooperative. Energy savings of over 20% were obtained. Most important, the procedures and materials implemented in the demonstration project have been adapted to Polish conditions and applied to other housing cooperatives, schools, andmore » hospitals. Additional projects are being planned, in Krakow and other cities, under the direction of FEWE-Krakow, the Polish Energie Cities Network, and Biuro Rozwoju Krakowa.« less

The Strategic Technologies for Automation and Robotics (STEAR) program: Protection of materials in the space environment subprogram

NASA Technical Reports Server (NTRS)

Schmidt, Lorne R.; Francoeur, J.; Aguero, Alina; Wertheimer, Michael R.; Klemberg-Sapieha, J. E.; Martinu, L.; Blezius, J. W.; Oliver, M.; Singh, A.

1995-01-01

Three projects are currently underway for the development of new coatings for the protection of materials in the space environment. These coatings are based on vacuum deposition technologies. The projects will go as far as the proof-of-concept stage when the commercial potential for the technology will be demonstrated on pilot-scale fabrication facilities in 1996. These projects are part of a subprogram to develop supporting technologies for automation and robotics technologies being developed under the Canadian Space Agency's STEAR Program, part of the Canadian Space Station Program.

Project Rescue: So Close and yet so Far

ERIC Educational Resources Information Center

Laster, Stephen

2011-01-01

This is the third installment in a four-part series that follows the exploits of Gene, a well-established CIO of a sizable IT organization at a top-100 university. Gene has been working with his team to regain the trust of the campus through Project Rescue, a 30-day turnaround plan focused on demonstrating IT's value. Project Rescue has two…

Project Developmental Continuity Evaluation: Implementation Rating Instrument.

ERIC Educational Resources Information Center

High/Scope Educational Research Foundation, Ypsilanti, MI.

This instrument is part of a series of documents on the evaluation of Project Developmental Continuity (PDC), a Head Start demonstration program aimed at providing educational and developmental continuity between children's Head Start and primary school experiences. The Implementation Rating Instrument (IRI) was developed to provide a quantitative…

Biculturalism through Experiential Language Learning.

ERIC Educational Resources Information Center

Brennan, Pamela; Donoghue, Anna Acitelli

This paper describes the English as a Second Language Program developed for educationally disadvantaged Mexican-American adults as part of the educational offerings of Project Step-Up, an OEO-funded demonstration program in San Diego. Project Step-Up features a multifold methodological approach incorporating techniques from (1) life skills…

Afferent projections to the deep mesencephalic nucleus in the rat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veazey, R.B.; Severin, C.M.

1982-01-10

Afferent projections to the deep mesencephalic nucleus (DMN) of the rat were demonstrated with axonal transport techniques. Potential sources for projections to the DMN were first identified by injecting the nucleus with HRP and examining the cervical spinal cord, brain stem, and cortex for retrogradely labeled neurons. Areas consistently labeled were then injected with a tritiated radioisotope, the tissue processed for autoradiography, and the DMN examined for anterograde labeling. Afferent projections to the medial and/or lateral parts of the DMN were found to originate from a number of spinal, bulbar, and cortical centers. Rostral brain centers projecting to both medialmore » and lateral parts of the DMN include the ipsilateral motor and somatosensory cortex, the entopeduncular nucleus, and zona incerta. at the level of the midbrain, the ipsilateral substantia nigra and contralateral DMN likewise project to the DMN. Furthermore, the ipsilateral superior colliculus projects to the DMN, involving mainly the lateral part of the nucleus. Afferents from caudal centers include bilateral projections from the sensory nucleus of the trigeminal complex and the nucleus medulla oblongata centralis, as well as from the contralateral dentate nucleus. The projections from the trigeminal complex and nucleus medullae oblongatae centralis terminate in the intermediate and medial parts of the DMN, whereas projections from the contralateral dentate nucleus terminate mainly in its lateral part. In general, the afferent connections of the DMN arise from diverse areas of the brain. Although most of these projections distribute throughout the entire extent of the DMN, some of them project mainly to either medial or lateral parts of the nucleus, thus suggesting that the organization of the DMN is comparable, at least in part, to that of the reticular formation of the pons and medulla, a region in which hodological differences between medial and lateral subdivisions are known to exist.« less

Calamity Hollow Mine Fire Project. 3. Instrumentation for combustion monitoring, process control, and data recording. Report of investigations/1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dalverny, L.E.; Chaiken, R.F.; Soroka, K.E.

1984-01-01

This report is the third in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5.) This part (part 3) describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 both deal with the closeout phase of the fieldmore » demonstration. Part 4 describes the procedure used to quench the fire, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion (WIFE) is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and the WIFE quenching procedure are planned.« less

Technology Foresight For Youth: A Project For Science and Technology Education in Sweden

NASA Astrophysics Data System (ADS)

Kendal, Anne Louise

"Technology Foresight for Youth" is a project run by two science museums, two science centres and "Technology Foresight (Sweden)" an organization in which both business and scientists are represented. The project is designed to strengthen young people's interest in ongoing technological work, research and education. It should give them confidence in their own ability both to understand today's techniques including its influence on people's daily lives, and to influence future developments. One part of the project is aimed at school teachers, teacher cooperation groups and students in the age group 12 to 18 years. A second part encourages dialog and meetings by arranging debates, seminars, theatre, science demonstrations in cooperation with business representatives and scientists. A third important part of the project is a special exhibition to be shown at the four cooperating institutions: "To be where I am not - young people's dreams about the future". The exhibition is meant to be sensual, interactive and partly virtual. It will change and grow with time as young people contribute with their thoughts, visions and challenges. Young people in different parts of the country will be able to interact electronically with each other and with the virtual part of the exhibition. The main aim of the project is to develop new interactive pedagogic methods for science and technology based on young people's own visions about the future.

Political polarization projection: social projection of partisan attitude extremity and attitudinal processes.

PubMed

Van Boven, Leaf; Judd, Charles M; Sherman, David K

2012-07-01

What influences perceptions of political polarization? The authors examine the polarization of people's own political attitudes as a source of perceived polarization: Individuals with more extreme partisan attitudes perceive greater polarization than individuals with less extreme partisan attitudes. This "polarization projection" was demonstrated in 3 studies in which people estimated the distribution of others' political attitudes: one study with a nationally representative sample concerning the 2008 presidential election, and 2 studies concerning university students evaluating a policy regarding scarce resource allocation. These studies demonstrate that polarization projection occurs simultaneously with and independently of simple projection, the tendency to assume that others share one's partisan political attitudes. Polarization projection may occur partly because people assume that others engage in similar attitudinal processes as the self, such as extensive thought and emotional arousal. The projection of various attitudinal processes was demonstrated in a study concerning health care reform policies. Further supporting this explanation, polarization projection increased when people introspected about their own attitudinal processes, which increased the accessibility of those processes. Implications for perceptions of partisanship, social judgment, and civic behavior are discussed.

The Childhood Obesity Research Demonstration project: a team approach for supporting a multisite, multisector intervention.

PubMed

Williams, Nancy; Dooyema, Carrie A; Foltz, Jennifer L; Belay, Brook; Blanck, Heidi M

2015-02-01

Comprehensive multisector, multilevel approaches are needed to address childhood obesity. This article introduces the structure of a multidisciplinary team approach used to support and guide the multisite, multisector interventions implemented as part of the Childhood Obesity Research Demonstration (CORD) project. This article will describe the function, roles, and lessons learned from the CDC-CORD approach to project management. The CORD project works across multisectors and multilevels in three demonstration communities. Working with principal investigators and their research teams who are engaging multiple stakeholder groups, including community organizations, schools and child care centers, health departments, and healthcare providers, can be a complex endeavor. To best support the community-based research project, scientific and programmatic expertise in a wide range of areas was required. The team was configured based on the skill sets needed to interact with the various levels of staff working with the project. By thoughtful development of the team and processes, an efficient system for supporting the multisite, multisector intervention project sites was developed. The team approach will be formally evaluated at the end of the project period.

Project Developmental Continuity: Field Procedures Manual.

ERIC Educational Resources Information Center

Morris, Mary

This operations manual for field staff (site monitors, site coordinators, and testers) involved in the observation and testing of children is part of a series of documents on the evaluation of Project Developmental Continuity (PDC), a Head Start demonstration program aimed at providing educational and developmental continuity between children's…

Project Developmental Continuity Evaluation: Site Visitors' Manual.

ERIC Educational Resources Information Center

Morris, Mary; Smith, Allen

This site visitors' manual is part of a series of documents on the evaluation of Project Developmental Continuity (PDC), a Head Start demonstration program aimed at providing educational and developmental continuity between children's Head Start and primary school experiences. The PDC evaluation documents and analyzes the process of program…

49 CFR 350.105 - What definitions are used in this part?

Code of Federal Regulations, 2010 CFR

2010-10-01

... activities and projects that improve CMV safety and compliance with CMV safety regulations (including activities and projects that are national in scope), increase public awareness and education, demonstrate new technologies, and reduce the number and rate of accidents involving CMVs. Incentive Funds means funds awarded...

Flat-plate solar array project. Volume 5: Process development

NASA Technical Reports Server (NTRS)

Gallagher, B.; Alexander, P.; Burger, D.

1986-01-01

The goal of the Process Development Area, as part of the Flat-Plate Solar Array (FSA) Project, was to develop and demonstrate solar cell fabrication and module assembly process technologies required to meet the cost, lifetime, production capacity, and performance goals of the FSA Project. R&D efforts expended by Government, Industry, and Universities in developing processes capable of meeting the projects goals during volume production conditions are summarized. The cost goals allocated for processing were demonstrated by small volume quantities that were extrapolated by cost analysis to large volume production. To provide proper focus and coverage of the process development effort, four separate technology sections are discussed: surface preparation, junction formation, metallization, and module assembly.

34 CFR 376.30 - What priorities are considered for support by the Secretary under this part?

Code of Federal Regulations, 2012 CFR

2012-07-01

... demonstrate effective Statewide approaches to transitional rehabilitation service delivery for youths with... illness, mental retardation, and learning disability. (d) Transitional rehabilitation services for institutionalized persons. This priority supports projects that demonstrate effective ways to assist youths and...

34 CFR 376.30 - What priorities are considered for support by the Secretary under this part?

Code of Federal Regulations, 2011 CFR

2011-07-01

... demonstrate effective Statewide approaches to transitional rehabilitation service delivery for youths with... illness, mental retardation, and learning disability. (d) Transitional rehabilitation services for institutionalized persons. This priority supports projects that demonstrate effective ways to assist youths and...

34 CFR 376.30 - What priorities are considered for support by the Secretary under this part?

Code of Federal Regulations, 2014 CFR

2014-07-01

... demonstrate effective Statewide approaches to transitional rehabilitation service delivery for youths with... illness, mental retardation, and learning disability. (d) Transitional rehabilitation services for institutionalized persons. This priority supports projects that demonstrate effective ways to assist youths and...

34 CFR 376.30 - What priorities are considered for support by the Secretary under this part?

Code of Federal Regulations, 2013 CFR

2013-07-01

... demonstrate effective Statewide approaches to transitional rehabilitation service delivery for youths with... illness, mental retardation, and learning disability. (d) Transitional rehabilitation services for institutionalized persons. This priority supports projects that demonstrate effective ways to assist youths and...

Rolling Thunder -- Integration of the Solo 161 Stirling engine with the CPG-460 solar concentrator at Ft. Huachuca

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diver, R.B.; Moss, T.A.; Goldberg, V.

Project Rolling Thunder is a dish/Stirling demonstration project at Ft. Huachuca, a US Army fort in southeastern Arizona (Huachuca means rolling thunder in Apache). It has been supported by the Strategic Environmental Research and Development Program (SERDP), a cooperative program between the Department of Defense (DoD) and the Department of Energy (DOE). As part of a 1992 SERDP project, Cummins Power Generation, Inc. (CPG) installed a CPG 7 kW(c) dish/Stirling system at the Joint Interoperability Test Command (JITC) in Ft. Huachuca, Arizona. The primary objective of the SERDP Dish/Stirling for DoD Applications project was to demonstrate a CPG 7-kW(c) dish/Stirlingmore » system at a military facility. Unfortunately, Cummins Engine Company decided to divest its solar operations. As a direct result of Ft. Huachuca`s interest in the Cummins dish/Stirling technology, Sandia explored the possibility of installing a SOLO 161 Stirling power conversion unit (PCU) on the Ft. Huachuca CPG-460. In January 1997, a decision was made to retrofit a SOLO 161 Stirling engine on the CPG-460 at Ft. Huachuca. Project Rolling Thunder. The SOLO 161 Demonstration at Ft. Huachuca has been a challenge. Although, the SOLO 161 PCU has operated nearly flawlessly and the CPG-460 has been, for the most part, a solid and reliable component, integration of the SOLO PCU with the CPG-460 has required significant attention. In this paper, the integration issues and technical approaches of project Rolling Thunder are presented. Lessons of the project are also discussed.« less

Current Projects in Vocational Education-FY 1976. Abstracts of Projects Supported in Fiscal Year 1976 and the Transition Quarter under the Vocational Education Amendments of 1968 (Parts C, D, I and J).

ERIC Educational Resources Information Center

Budke, Wesley E., Comp.; Gordon, Ruth, Comp.

This compilation presents abstracts of 221 new and continuing projects funded by the Division of Research and Demonstration (USOE/BOAE) in fiscal year 1976 and the transition quarter (July 1 - September 30, 1976). Following a narrative introduction and list of project titles, the abstracts are arranged alphabetically by State within each of the…

Arsenic and Nitrate Removal from Drinking Water by Ion Exchange U.S. EPA Demonstration Project at Vale, OR - Final Performance Evaluation Report

EPA Science Inventory

As part of the EPA Arsenic Removal Technology Demonstration Program, a 540-gal/min (gpm) ion exchange (IX) system proposed by Kinetico was selected for demonstration at Vale, OR to remove arsenic and nitrate from a groundwater supply to meet their respective maximum contaminant l...

Controlled Hydrogen Fleet and Infrastructure Demonstration and Validation Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stottler, Gary

General Motors, LLC and energy partner Shell Hydrogen, LLC, deployed a system of hydrogen fuel cell electric vehicles integrated with a hydrogen fueling station infrastructure to operate under real world conditions as part of the U.S. Department of Energy's Controlled Hydrogen Fleet and Infrastructure Validation and Demonstration Project. This technical report documents the performance and describes the learnings from progressive generations of vehicle fuel cell system technology and multiple approaches to hydrogen generation and delivery for vehicle fueling.

A Multi-scale, Multi-Model, Machine-Learning Solar Forecasting Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamann, Hendrik F.

The goal of the project was the development and demonstration of a significantly improved solar forecasting technology (short: Watt-sun), which leverages new big data processing technologies and machine-learnt blending between different models and forecast systems. The technology aimed demonstrating major advances in accuracy as measured by existing and new metrics which themselves were developed as part of this project. Finally, the team worked with Independent System Operators (ISOs) and utilities to integrate the forecasts into their operations.

Eco-Friendly Campuses as Teaching Tools

ERIC Educational Resources Information Center

Erwin, Stephen J.; Kearns, Thomas D.

2008-01-01

Sustainable design projects offer academic communities the opportunity to make the design and operations of their campuses part of the larger lessons of social and environmental responsibility that are integral parts of higher education. In no place is that demonstrated more clearly than in New England, with its long commitment to environmental…

Being in the World: An Existential Inquiry of Knowing One's Self through a Personal Project--In the Context of Dissertation Survival

ERIC Educational Resources Information Center

Kitajima, Tomoe

2012-01-01

This study--a philosophical exploration, partly in an autoethnographical account-provides an empirical demonstration that one's personal project has a strong and positive impact on the dissertation process both for endurance to complete the process and for quality of the product. The concept of project is often explained as one's pursuit…

A Demonstration Pilot Project of Comprehensive Library Services for the Aged in Selected Communities in Kentucky (NRTA/AARP Kentucky Library Project). Final Report, Phase 1.

ERIC Educational Resources Information Center

Carlson, Lawrence O.

The project, intended to design and field test models of specialized library services for older adults, was conducted in two parts. Phase 1 consisted of collecting and evaluating data for use in designing models in Louisville, Lexington, Somerset, and Hazard, Kentucky. Data was collected by search of the literature, personal interviews, a…

7 CFR Appendix A to Part 4280 - Technical Reports for Projects With Total Eligible Project Costs of $200,000 or Less

Code of Federal Regulations, 2011 CFR

2011-01-01

... of the wind turbine is 100kW or smaller and with a generator hub height of 120 feet or less. Small... demonstrate the amount of local wind resource where the small wind turbine is to be installed. Indicate the... of the individual wind turbine(s) is larger than 100kW. (a) Qualifications of key project service...

7 CFR Appendix A to Part 4280 - Technical Reports for Projects With Total Eligible Project Costs of $200,000 or Less

Code of Federal Regulations, 2010 CFR

2010-01-01

... of the wind turbine is 100kW or smaller and with a generator hub height of 120 feet or less. Small... demonstrate the amount of local wind resource where the small wind turbine is to be installed. Indicate the... of the individual wind turbine(s) is larger than 100kW. (a) Qualifications of key project service...

The ZOG Technology Demonstration Project: A System Evaluation of USS CARL VINSON (CVN 70)

DTIC Science & Technology

1984-12-01

part of a larger project involving development of a wide range of computer technologies, including artifcial intelligence and a long-range computer...shipboard manage- ment, aircraft management, expert systems, menu selection, man- machine interface, artificial intelligence , automation; shipboard It AWM...functions, planning, evaluation, training, hierarchical data bases The objective of this project was to conduct an evaluation of ZOG, a general purpose

Low NOx Fuel Flexible Combustor Integration Project Overview

NASA Technical Reports Server (NTRS)

Walton, Joanne C.; Chang, Clarence T.; Lee, Chi-Ming; Kramer, Stephen

2015-01-01

The Integrated Technology Demonstration (ITD) 40A Low NOx Fuel Flexible Combustor Integration development is being conducted as part of the NASA Environmentally Responsible Aviation (ERA) Project. Phase 2 of this effort began in 2012 and will end in 2015. This document describes the ERA goals, how the fuel flexible combustor integration development fulfills the ERA combustor goals, and outlines the work to be conducted during project execution.

X-43C Flight Demonstrator Project Overview

NASA Technical Reports Server (NTRS)

Moses, Paul L.

2003-01-01

The X-43C Flight Demonstrator Project is a joint NASA-USAF hypersonic propulsion technology flight demonstration project that will expand the hypersonic flight envelope for air-breathing engines. The Project will demonstrate sustained accelerating flight through three flights of expendable X-43C Demonstrator Vehicles (DVs). The approximately 16-foot long X-43C DV will be boosted to the starting test conditions, separate from the booster, and accelerate from Mach 5 to Mach 7 under its own power and autonomous control. The DVs will be powered by a liquid hydrocarbon-fueled, fuel-cooled, dual-mode, airframe integrated scramjet engine system developed under the USAF HyTech Program. The Project is managed by NASA Langley Research Center as part of NASA's Next Generation Launch Technology Program. Flight tests will be conducted by NASA Dryden Flight Research Center off the coast of California over water in the Pacific Test Range. The NASA/USAF/industry project is a natural extension of the Hyper-X Program (X-43A), which will demonstrate short duration (approximately 10 seconds) gaseous hydrogen-fueled scramjet powered flight at Mach 7 and Mach 10 using a heavy-weight, largely heat sink construction, experimental engine. The X-43C Project will demonstrate sustained accelerating flight from Mach 5 to Mach 7 (approximately 4 minutes) using a flight-weight, fuel-cooled, scramjet engine powered by much denser liquid hydrocarbon fuel. The X-43C DV design flows from integrating USAF HyTech developed engine technologies with a NASA Air-Breathing Launch Vehicle accelerator-class configuration and Hyper-X heritage vehicle systems designs. This paper describes the X-43C Project and provides the background for NASA's current hypersonic flight demonstration efforts.

The Habitat Demonstration Unit Project Overview

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Grill, Tracy R.; Tri, Terry O.; Howe, Alan S.

2010-01-01

This paper will describe an overview of the National Aeronautics and Space Administration (NASA) led multi-center Habitat Demonstration Unit (HDU) Project. The HDU project is a "technology-pull" project that integrates technologies and innovations from numerous NASA centers. This project will be used to investigate and validate surface architectures, operations concepts, and requirements definition of various habitation concepts. The first habitation configuration this project will build and test is the Pressurized Excursion Module (PEM). This habitat configuration - the PEM - is based on the Constellation Architecture Scenario 12.1 concept of a vertically oriented habitat module. The HDU project will be tested as part of the 2010 Desert Research and Technologies Simulations (D-RATS) test objectives. The purpose of this project is to develop, integrate, test, and evaluate a habitat configuration in the context of the mission architectures and surface operation concepts. A multi-center approach will be leveraged to build, integrate, and test the PEM through a shared collaborative effort of multiple NASA centers. The HDU project is part of the strategic plan from the Exploration Systems Mission Directorate (ESMD) Directorate Integration Office (DIO) and the Lunar Surface Systems Project Office (LSSPO) to test surface elements in a surface analog environment. The 2010 analog field test will include two Lunar Electric Rovers (LER) and the PEM among other surface demonstration elements. This paper will describe the overall objectives, its various habitat configurations, strategic plan, and technology integration as it pertains to the 2010 and 2011 field analog tests. To accomplish the development of the PEM from conception in June 2009 to rollout for operations in July 2010, the HDU project team is using a set of design standards to define the interfaces between the various systems of PEM and to the payloads, such as the Geology Lab, that those systems will support. Scheduled activities such as early fit-checks and the utilization of a habitat avionics test bed prior to equipment installation into PEM are planned to facilitate the integration process.

Reducing Plug Loads in Office Spaces: Hawaii and Guam Energy Improvement Technology Demonstration Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheppy, M.; Metzger, I.; Cutler, D.

2014-01-01

As part of its overall strategy to meet its energy goals, the Naval Facilities Engineering Command (NAVFAC) partnered with the Department of Energy's National Renewable Energy Laboratory (NREL) to rapidly demonstrate and deploy cost-effective renewable energy and energy efficiency technologies. This project was one of several demonstrations of new or underutilized commercial energy technologies. The common goal was to demonstrate and measure the performance and economic benefit of the system while monitoring any ancillary impacts to related standards of service and operation and maintenance (O&M) practices. In short, demonstrations at naval facilities simultaneously evaluate the benefits and compatibility of themore » technology with the U.S. Department of Defense (DOD) mission, and with NAVFAC's design, construction, operations, and maintenance practices, in particular. This project demonstrated the performance of commercially available advanced power strips (APSs) for plug load energy reductions in building A4 at Joint Base Pearl Harbor-Hickam (JBPHH), Hawaii.« less

NASA's F-15B from the Dryden Flight Research Center flew in the supersonic shockwave of a modified U.S. Navy F-5E jet in support of the Shaped Sonic Boom Demonstration (SSBD) project. On Aug. 27, 2003, the F-5 SSBD aircraft demonstrated a method to reduce

NASA Image and Video Library

2003-08-25

NASA's F-15B research testbed jet from NASA's Dryden Flight Research Center flew in the supersonic shockwave of a Northrop Grumman Corp. modified U.S. Navy F-5E jet in support of the Shaped Sonic Boom Demonstration (SSBD) project, which is part of the DARPA's Quiet Supersonic Platform (QSP) program. On Aug. 27, 2003, the F-5 SSBD aircraft demonstrated a method to reduce the intensity of sonic booms.

Non-Flow-Through Fuel Cell System Test Results and Demonstration on the SCARAB Rover

NASA Technical Reports Server (NTRS)

Scheidegger, Brianne, T.; Burke, Kenneth A.; Jakupca, Ian J.

2012-01-01

This paper describes the results of the demonstration of a non-flow-through PEM fuel cell as part of a power system on the SCARAB rover. A 16-cell non-flow-through fuel cell stack from Infinity Fuel Cell and Hydrogen, Inc. was incorporated into a power system designed to act as a range extender by providing power to the rover s hotel loads. This work represents the first attempt at a ground demonstration of this new technology aboard a mobile test platform. Development and demonstration were supported by the Office of the Chief Technologist s Space Power Systems Project and the Advanced Exploration System Modular Power Systems Project.

REVIEW OF SELECTED STATE-OF-THE-ART APPLICATIONS OF DIAGNOSTIC MEASUREMENTS FOR RADON MITIGATION PLANNING

EPA Science Inventory

Since late-1984, EPA's AEERL has supported a program to develop and demonstrate radon mitigation techniques for single-family detached dwellings. As part of the program, projects have been started directed at developing and demonstrating the use of diagnostic measurements in all ...

Fission Surface Power Systems (FSPS) Project Final Report for the Exploration Technology Development Program (ETDP): Fission Surface Power, Transition Face to Face

NASA Technical Reports Server (NTRS)

Palac, Donald T.

2011-01-01

The Fission Surface Power Systems Project became part of the ETDP on October 1, 2008. Its goal was to demonstrate fission power system technology readiness in an operationally relevant environment, while providing data on fission system characteristics pertinent to the use of a fission power system on planetary surfaces. During fiscal years 08 to 10, the FSPS project activities were dominated by hardware demonstrations of component technologies, to verify their readiness for inclusion in the fission surface power system. These Pathfinders demonstrated multi-kWe Stirling power conversion operating with heat delivered via liquid metal NaK, composite Ti/H2O heat pipe radiator panel operations at 400 K input water temperature, no-moving-part electromagnetic liquid metal pump operation with NaK at flight-like temperatures, and subscale performance of an electric resistance reactor simulator capable of reproducing characteristics of a nuclear reactor for the purpose of system-level testing, and a longer list of component technologies included in the attached report. Based on the successful conclusion of Pathfinder testing, work began in 2010 on design and development of the Technology Demonstration Unit (TDU), a full-scale 1/4 power system-level non-nuclear assembly of a reactor simulator, power conversion, heat rejection, instrumentation and controls, and power management and distribution. The TDU will be developed and fabricated during fiscal years 11 and 12, culminating in initial testing with water cooling replacing the heat rejection system in 2012, and complete testing of the full TDU by the end of 2014. Due to its importance for Mars exploration, potential applicability to missions preceding Mars missions, and readiness for an early system-level demonstration, the Enabling Technology Development and Demonstration program is currently planning to continue the project as the Fission Power Systems project, including emphasis on the TDU completion and testing.

A COMPREHENSIVE PROGRAM IN ENGLISH FOR THE 7TH, 8TH AND 9TH GRADE --LITERATURE, LANGUAGE, COMPOSITION, FOR HONORS STUDENTS AND AVERAGE STUDENTS. PART 2, CONSTRUCTING ACHIEVEMENT TESTS DURING A SUMMER WORKSHOP FOR PARTIAL EVALUATION OF A PROJECT ENGLISH DEMON. CTR.

ERIC Educational Resources Information Center

HILLOCKS, GEORGE, JR.; KEARNEY, PATRICIA A.

THIS FINAL REPORT OF THE EUCLID ENGLISH DEMONSTRATION CENTER DESCRIBES THE CREATION OF A JUNIOR HIGH SCHOOL ENGLISH PROGRAM IN LITERATURE, LANGUAGE, AND COMPOSITION. PART 1 OF THE REPORT DISCUSSES (1) THE PRODUCTION AND DEMONSTRATION OF 31 THEMATICALLY-DEVELOPED TEACHING UNITS, (2) A SERIES OF SHORT, CONCEPT-CENTERED CONFERENCES TO EDUCATE…

Nuclear Power 2010 Program Dominion Virginia Power Cooperative Project U.S. Department of Energy Cooperative Agreement DE-FC07-05ID14635 Construction and Operating License Demonstration Project Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eugene S. Grecheck

2010-11-30

This report serves to summarize the major activities completed as part of Virginia Electric and Power Company's North Anna construction and operating license demonstration project with DOE. Project successes, lessons learned, and suggestions for improvement are discussed. Objectives of the North Anna COL project included preparation and submittal of a COLA to the USNRC incorporating ESBWR technology for a third unit a the North Anna Power Station site, support for the NRC review process and mandatory hearing, obtaining NRC approval of the COLA and issuance of a COL, and development of a business case necessary to support a decision onmore » building a new nuclear power plant at the North Anna site.« less

The NYA/UCLA Project: A Community-University Model for Mental Health Training.

ERIC Educational Resources Information Center

Jacobs, Marion K.; And Others

This three-part paper describes a pilot demonstration project for training psychology graduate students and social-work agency personnel to provide mental health services for minority adolescents and their families. The training model assumes that all participants possess skill and knowledge that can be shared with each other and that a strong…

EVALUATION OF ROOSEVELT SUMMER DEMONSTRATION PROGRAM, 1967.

ERIC Educational Resources Information Center

RICHARDSON, JOY B.

THE FIRST PART OF THIS REPORT OF A SENATE BILL 28 DEMONSTRATION PROJECT DESCRIBES THE SUMMER JUNIOR HIGH SCHOOL PROGRAM IN WHICH STUDENTS WERE OFFERED (1) LANGUAGE INSTRUCTION TO IMPROVE THEIR READING ACHIEVEMENT, (2) AN INNOVATIVE MATHEMATICS COURSE CONDUCTED BY THE "DISCOVERY METHOD," AND (3) SPANISH-ENGLISH LANGUAGE CLASSES TO ENABLE PUPILS OF…

Costs of Arsenic Removal Technologies for Small Water Systems: U.S. EPA Arsenic Removal Technology Demonstration Program

EPA Science Inventory

As part of the Arsenic Rule Implementation Research Program, between July 2003 and July 2011, the U.S. environmental Protection Agency (EPA) conducted 50 full-scale demonstration projects on treatment systems removing arsenic from drinking water in 26 states throughout the U.S. ...

A Case Study of Technical Assistance to Demonstration Programs for Young Handicapped Children. Part II.

ERIC Educational Resources Information Center

Behr, Shirley K.; And Others

A project to provide technical assistance to staffs of two demonstration programs for preschool handicapped children and their families is described. The focus was technical assistance developed and exercised by the Technical Assistance Development System (TADS), which assisted in the development of the Handicapped Children's Early Education…

Seeing the LITE

NASA Astrophysics Data System (ADS)

Brecher, K.

2000-12-01

We are developing a number of eyes-on experiments, lecture demonstrations and Web based JAVA applets about light, optics, color and visual perception as part of `Project LITE - Light Inquiry Through Experiments'. These are intended for incorporation into introductory level university science courses in astronomy, physics and other disciplines. In this presentation, several of the new LITE demonstrations applicable to large astronomy and physics classes will be shown. One demonstration involves novel materials to display Rayleigh scattering (blue skies, red sunsets and interstellar reddening - NOT redshift!) - including polarization effects. Others employ incandescent bulbs, LED's and laser pointers to illustrate fluorescence, diffraction and other physical and quantum optics phenomena. Still other demonstrations utilize transparent plastic moire overlays as well as computer animated moire patterns to show a variety of astronomical and physical phenomena. We will also display some of our applets posted at the Project LITE Web site (http://www.bu.edu/smec/lite) as well as the associated kit of optical materials we have developed for use by individual students in their own homes or dormitory rooms. This work was supported in part by NSF grant # DUE-9950551.

78 FR 34655 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... also be made to better define minimally successful performance for assignments involving displacement..., third block Part 351, subpart G, section 351.701--Assignment Involving Displacement, replace paragraph...

Strontium-90 Error Discovered in Subcontract Laboratory Spreadsheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. D. Brown A. S. Nagel

1999-07-31

West Valley Demonstration Project health physicists and environment scientists discovered a series of errors in a subcontractor's spreadsheet being used to reduce data as part of their strontium-90 analytical process.

Professional changes induced by a redesigned immunization supply chain in the Comé Health Zone, Benin.

PubMed

Guillermet, Elise; Alfa, Daleb Abdoulaye; Gbodja, Romule; Jaillard, Philippe

2017-04-19

At the end of 2013, the Government of Benin and Agence de Médecine Préventive (AMP) launched a demonstration project in Comé Health Zone (HZ) to optimize the vaccine supply chain. A key part of the demonstration project was the creation of an "informed push model" of vaccine distribution supported by a new logistician position at the health zone (district) level. At the conclusion of the demonstration project in 2015, the authors conducted an anthropological study consisting of semi-structured interviews with 62 participants to assess how the new model changed the professional identities, roles, responsibilities, and practices of personnel involved in vaccine management during and just after the demonstration project end in Comé HZ. The study found that health workers considered the logistician as a key player in enabling them to perform their public health mission, notably by improving knowledge and practices in vaccine management, providing supportive supervision, and improving the availability of vaccines and other supplies so that immunization sessions could occur more reliably and professionally within the communities they served. The demonstration project was widely accepted among study participants. The study was approved by the Cotonou Ethics Committee (CER-ISBA No. 56 dated 09/04/2015). Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Earth System (ES-DOC) Project

NASA Astrophysics Data System (ADS)

Greenslade, Mark; Murphy, Sylvia; Treshansky, Allyn; DeLuca, Cecilia; Guilyardi, Eric; Denvil, Sebastien

2014-05-01

ESSI1.3 New Paradigms, Modelling, and International Collaboration Strategies for Earth System Sciences Earth System Documentation (ES-DOC) is an international project supplying tools & services in support of earth system documentation creation, analysis and dissemination. It is nurturing a sustainable standards based documentation eco-system that aims to become an integral part of the next generation of exa-scale dataset archives. ES-DOC leverages open source software and places end-user narratives at the heart of all it does. ES-DOC has initially focused upon nurturing the Earth System Model (ESM) documentation eco-system. Within this context ES-DOC leverages emerging documentation standards and supports the following projects: Coupled Model Inter-comparison Project Phase 5 (CMIP5); Dynamical Core Model Inter-comparison Project (DCMIP); National Climate Predictions and Projections Platforms Quantitative Evaluation of Downscaling Workshop. This presentation will introduce the project to a wider audience and demonstrate the range of tools and services currently available for use. It will also demonstrate how international collaborative efforts are essential to the success of ES-DOC.

Disasters as a necessary part of benefit-cost analyses.

PubMed

Mark, R K; Stuart-Alexander, D E

1977-09-16

Benefit-cost analyses for water projects generally have not included the expected costs (residual risk) of low-probability disasters such as dam failures, impoundment-induced earthquakes, and landslides. Analysis of the history of these types of events demonstrates that dam failures are not uncommon and that the probability of a reservoir-triggered earth-quake increases with increasing reservoir depth. Because the expected costs from such events can be significant and risk is project-specific, estimates should be made for each project. The cost of expected damage from a "high-risk" project in an urban area could be comparable to project benefits.

DOE tallies Class III oil recovery field projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-07-25

Here are details from midterm proposals submitted as part of the US Department of Energy's Class 3 oil recovery field demonstration candidate projects. All of the proposals emphasize dissemination of project details so that the results, if successful, can be applied widely in similar reservoirs. Project results will also be fed into a national petroleum technology transfer network. The proposals include: Gulf of Mexico, Gulf coast, offshore California, a California thermal, immiscible CO[sub 2], produced/potable water, microbial EOR, California diatomite, West Texas Spraberry field, and other Permian Basin fields.

An Evolutionary Journey: The Case Study of East Muskingum Middle School. Transforming Learning Communities.

ERIC Educational Resources Information Center

Morrow, Linda E.; Martin, Kaye M.; Glascock, Catherine H.

This book is part of a series of case studies that demonstrate better ways to educate Ohio's students. The case study is part of the Transforming Learning Communities (TLC) Project, designed to support significant school-reform efforts among Ohio's elementary, middle, and high schools. This report describes the implementation of an innovative…

A Process Evaluation of Project Developmental Continuity. Interim Report IV, Volume I: Pilot Year Impact Study--Instrument Characteristics and Attrition Trends.

ERIC Educational Resources Information Center

Granville, Arthur C.; And Others

This interim report of a pilot year impact study on evaluation methodology is part of a series of documents on the evaluation of Project Developmental Continuity, a Head Start demonstration program aimed at promoting educational and developmental continuity between children's Head Start and primary school experiences. This report deals with…

Solar hot water demonstration project at Red Star Industrial Laundry, Fresno, California

NASA Technical Reports Server (NTRS)

1980-01-01

The performance of a Solar Hot Water System at a laundry in Fresno, California is described. The system features an integrated wastewater heat recovery subsystem and a solar preheating system designed to supply a part of the hot water requirements. Performance data for a six month period are projected to an annual savings of $18,703.

Efficient design based on perturbed parameter ensembles to identify plausible and diverse variants of a model for climate change projections

NASA Astrophysics Data System (ADS)

Karmalkar, A.; Sexton, D.; Murphy, J.

2017-12-01

We present exploratory work towards developing an efficient strategy to select variants of a state-of-the-art but expensive climate model suitable for climate projection studies. The strategy combines information from a set of idealized perturbed parameter ensemble (PPE) and CMIP5 multi-model ensemble (MME) experiments, and uses two criteria as basis to select model variants for a PPE suitable for future projections: a) acceptable model performance at two different timescales, and b) maintaining diversity in model response to climate change. We demonstrate that there is a strong relationship between model errors at weather and climate timescales for a variety of key variables. This relationship is used to filter out parts of parameter space that do not give credible simulations of historical climate, while minimizing the impact on ranges in forcings and feedbacks that drive model responses to climate change. We use statistical emulation to explore the parameter space thoroughly, and demonstrate that about 90% can be filtered out without affecting diversity in global-scale climate change responses. This leads to identification of plausible parts of parameter space from which model variants can be selected for projection studies.

Deep Stimulation at Newberry Volcano EGS Demonstration

NASA Astrophysics Data System (ADS)

Grasso, K.; Cladouhos, T. T.; Petty, S.; Garrison, G. H.; Nordin, Y.; Uddenberg, M.; Swyer, M.

2014-12-01

The Newberry Volcano EGS Demonstration is a 5 year field project designed to demonstrate recent technological advances for engineered geothermal systems (EGS) development. Advances in reservoir stimulation, diverter, and monitoring are being tested in a hot (>300 C), dry well (NWG 55-29) drilled in 2008. These technologies could reduce the cost of electrical power generation. The project began in 2010 with two years of permitting, technical planning, and development of a project-specific Induced Seismicity Mitigation Plan (ISMP), and is funded in part by the Department of Energy. In 2012, the well was hydraulically stimulated with water at pressures below the principle stress for 7 weeks, resulting in hydroshearing. The depth of stimulation was successfully shifted by injection of two pills of Thermally-degradable Zonal Isolation Materials (TZIMs). Injectivity changes, thermal profiles and seismicity indicate that fracture permeability in well NWG 55-29 was enhanced during stimulation. This work successfully demonstrated the viability of large-volume (40,000 m3), low-pressure stimulation coupled with non-mechanical diverter technology, and microseismic monitoring for reservoir mapping. Further analysis and field testing in 2013 indicates further stimulation will be required in order to develop an economically viable reservoir, and is scheduled in 2014. The 2014 stimulation will use improved stimulation and monitoring equipment, better knowledge based on 2012 outcomes, and create a deep EGS reservoir in the hottest part of the wellbore.

GEWEX America Prediction Project (GAPP) Science and Implementation Plan

NASA Technical Reports Server (NTRS)

2004-01-01

The purpose of this Science and Implementation Plan is to describe GAPP science objectives and the activities required to meet these objectives, both specifically for the near-term and more generally for the longer-term. The GEWEX Americas Prediction Project (GAPP) is part of the Global Energy and Water Cycle Experiment (GEWEX) initiative that is aimed at observing, understanding and modeling the hydrological cycle and energy fluxes at various time and spatial scales. The mission of GAPP is to demonstrate skill in predicting changes in water resources over intraseasonal-to-interannual time scales, as an integral part of the climate system.

The development of the Project NetWork administrative records database for policy evaluation.

PubMed

Rupp, K; Driessen, D; Kornfeld, R; Wood, M

1999-01-01

This article describes the development of SSA's administrative records database for the Project NetWork return-to-work experiment targeting persons with disabilities. The article is part of a series of papers on the evaluation of the Project NetWork demonstration. In addition to 8,248 Project NetWork participants randomly assigned to receive case management services and a control group, the simulation identified 138,613 eligible nonparticipants in the demonstration areas. The output data files contain detailed monthly information on Supplemental Security Income (SSI) and Disability Insurance (DI) benefits, annual earnings, and a set of demographic and diagnostic variables. The data allow for the measurement of net outcomes and the analysis of factors affecting participation. The results suggest that it is feasible to simulate complex eligibility rules using administrative records, and create a clean and edited data file for a comprehensive and credible evaluation. The study shows that it is feasible to use administrative records data for selecting control or comparison groups in future demonstration evaluations.

Improved recovery demonstration for Williston Basin carbonates. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sippel, M.A.

The purpose of this project was to demonstrate targeted infill and extension drilling opportunities, better determinations of oil-in-place, and methods for improved completion efficiency. The investigations and demonstrations were focussed on Red River and Ratcliffe reservoirs in the Williston Basin within portions of Montana, North Dakota and South Dakota. Both of these formations have been successfully explored with conventional 2-dimensional (2D) seismic. Improved reservoir characterization utilizing 3-dimensional (3D) seismic was investigated for identification of structural and stratigraphic reservoir compartments. These seismic characterizations were integrated with geological and engineering studies. The project tested lateral completion techniques, including high-pressure jetting lance technologymore » and short-radius lateral drilling to enhance completion efficiency. Lateral completions should improve economics for both primary and secondary oil where low permeability is a problem and higher-density drilling of vertical infill wells is limited by drilling cost. New vertical wells were drilled to test bypassed oil in ares that were identified by 3D seismic. These new wells are expected to recover as much or greater oil than was produced by nearby old wells. The project tested water injection through vertical and horizontal wells in reservoirs where application of waterflooding has been limited. A horizontal well was drilled for testing water injection. Injection rates were tested at three times that of a vertical well. This demonstration well shows that water injection with horizontal completions can improve injection rates for economic waterflooding. This report is divided into two sections, part 1 covers the Red River and part 2 covers the Ratcliffe. Each part summarizes integrated reservoir characterizations and outlines methods for targeting by-passed oil reserves in the respective formation and locality.« less

76 FR 29252 - Part F Special Projects of National Significance Program Cooperative Agreement Under the Ryan...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-20

... level data from 10 demonstration sites, and disseminated preliminary descriptive information on... required human subjects research approvals. The SPNS Enhancing Linkages ESC is the best qualified Grantee...

Single Body Parts are Processed by Individual Neurons in the Mouse Dorsolateral Striatum

PubMed Central

Coffey, Kevin R.; Nader, Miles; West, Mark O.

2016-01-01

Interest in the dorsolateral striatum (DLS) has generated numerous scientific studies of its neuropathologies, as well as its roles in normal sensorimotor integration and learning. Studies are informed by knowledge of DLS functional organization, the guiding principle being its somatotopic afferent projections from primary somatosensory (S1) and motor (M1) cortices. The potential to connect behaviorally relevant function to detailed structure is elevated by mouse models, which have access to extensive genetic neuroscience tool kits. Remaining to be demonstrated, however, is whether the correspondence between S1/M1 corticostriatal terminal distributions and the physiological properties of DLS neurons demonstrated in rats and non-human primates exists in mice. Given that the terminal distribution of S1/M1 projections to the DLS in mice is similar to that in rats, we studied whether firing rates (FRs) of DLS neurons in awake, behaving mice are related to activity of individual body parts. MSNs exhibited robust, selective increases in FR during movement or somatosensory stimulation of single body parts. Properties of MSNs, including baseline FRs, locations, responsiveness to stimulation, and proportions of responsive neurons were similar to properties observed in rats. Future studies can be informed by the present demonstration that the mouse lateral striatum functions as a somatic sensorimotor sector of the striatum and appears to be a homolog of the primate putamen, as demonstrated in rats (Carelli and West, 1991). PMID:26827625

A Process Evaluation of Project Developmental Continuity, Interim Report VII, Volume 3: Assessment of Program Impact Through the Head Start Year.

ERIC Educational Resources Information Center

Granville, Arthur C.; And Others

This interim report, part of a series of documents examining the feasibility of the longitudinal evaluation of Project Developmental Continuity (PDC), presents the results of an analysis of PDC impact at the Head Start level, using Spring 1977 data. PDC is a Head Start Demonstration Program aimed at providing educational and developmental…

Finding Multiple Internal Rates of Return for a Project with Non-Conventional Cash Flows: Utilizing Popular Financial/Graphing Calculators and Spreadsheet Software

ERIC Educational Resources Information Center

Chen, Jeng-Hong

2008-01-01

This study demonstrates that a popular graphing calculator among students, TI-83 Plus, has a powerful function to draw the NPV profile and find the accurate multiple IRRs for a project with non-conventional cash flows. However, finance textbooks or related supplementary materials do not provide students instructions for this part. The detailed…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kisner, R.; Melin, A.; Burress, T.

The objective of this project is to demonstrate improved reliability and increased performance made possible by deeply embedding instrumentation and controls (I&C) in nuclear power plant (NPP) components and systems. The project is employing a highly instrumented canned rotor, magnetic bearing, fluoride salt pump as its I&C technology demonstration platform. I&C is intimately part of the basic millisecond-by-millisecond functioning of the system; treating I&C as an integral part of the system design is innovative and will allow significant improvement in capabilities and performance. As systems become more complex and greater performance is required, traditional I&C design techniques become inadequate andmore » more advanced I&C needs to be applied. New I&C techniques enable optimal and reliable performance and tolerance of noise and uncertainties in the system rather than merely monitoring quasistable performance. Traditionally, I&C has been incorporated in NPP components after the design is nearly complete; adequate performance was obtained through over-design. By incorporating I&C at the beginning of the design phase, the control system can provide superior performance and reliability and enable designs that are otherwise impossible. This report describes the progress and status of the project and provides a conceptual design overview for the platform to demonstrate the performance and reliability improvements enabled by advanced embedded I&C.« less

Development of performance properties of ternary mixtures : field demonstrations and project summary.

DOT National Transportation Integrated Search

2012-07-01

Supplementary cementitious materials (SCM) have become common parts of modern concrete practice. The blending of two or three : cementitious materials to optimize durability, strength, or economics provides owners, engineers, materials suppliers, and...

Sum of the Parts.

ERIC Educational Resources Information Center

Science Activities, 1995

1995-01-01

Presents a Project WET water education activity. Students demonstrate how everyone contributes to the pollution of a river as it flows through a watershed and recognize that everyone's "contribution" can be reduced. Student distinguish between point- and nonpoint-source pollution. (LZ)

From Engineering Science to Big Science: The NACA and NASA Collier Trophy Research Project Winners

NASA Technical Reports Server (NTRS)

Mack, Pamela E. (Editor)

1998-01-01

The chapters of this book discuss a series of case studies of notable technological projects carried out at least in part by the NACA and NASA. The case studies chosen are those projects that won the National Aeronautic Association's (NAA) Collier Trophy for "the greatest achievement in aviation in America, the value of which has been thoroughly demonstrated by use during the preceding year." Looking back on the whole series of projects we can examine both what successes were seen as important at various times, and how the goals and organization of these notable projects changed over time.

[Demography perspectives and forecasts of the demand for electricity].

PubMed

Roy, L; Guimond, E

1995-01-01

"Demographic perspectives form an integral part in the development of electric load forecasts. These forecasts in turn are used to justify the addition and repair of generating facilities that will supply power in the coming decades. The goal of this article is to present how demographic perspectives are incorporated into the electric load forecasting in Quebec. The first part presents the methods, hypotheses and results of population and household projections used by Hydro-Quebec in updating its latest development plan. The second section demonstrates applications of such demographic projections for forecasting the electric load, with a focus on the residential sector." (SUMMARY IN ENG AND SPA) excerpt

Concept of operations : Dallas Integrated Corridor Management (ICM) demonstration project.

DOT National Transportation Integrated Search

2010-06-01

This concept of operations (Con Ops) for the US-75 Integrated Corridor Management (ICM) Program has been developed as part of the US Department of Transportation Integrated Corridor Management Initiative, which is an innovative research initiative th...

Overview of Louisville Trials

EPA Science Inventory

This slide presentation provides an overview of field demonstrations of condition assessment and leak detection technologies for water mains that are being conducted in Louisville, KY in cooperation with the Louisville Water Company. The project is part of the EPA Office of Rese...

Energy Systems Integration: Demonstrating Distribution Feeder Voltage Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-01

Overview fact sheet about the Smarter Grid Solutions Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

Energy Systems Integration: Demonstrating Distributed Grid-Edge Control Hierarchy

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-01

Overview fact sheet about the OMNETRIC Group Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

The use of weather data to predict non-recurring traffic congestion

DOT National Transportation Integrated Search

2006-08-01

This project will demonstrate the quantitative relationship between weather patterns and surface traffic conditions. The aviation and maritime industries use weather measurements and predictions as a normal part of operations, and this can be extende...

ADVANCED MANUFACTURING TEAM

NASA Image and Video Library

2016-03-17

KEN COOPER, TEAM LEAD OF MSFC’S ADVANCED MANUFACTURING TEAM, WITH NICKEL ALLOY 718 PARTS FABRICATED USING THE M1 SELECTIVE LASER MELTING SYSTEM. THE M1 MACHINE IS DEDICATED TO BUILDING QUALIFICATION SAMPLES AND HARDWARE DEMONSTRATORS FOR THE RS25 ENGINE PROJECT.

Large Scale Evaluation fo Nickel Aluminide Rolls

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2005-09-01

This completed project was a joint effort between Oak Ridge National Laboratory and Bethlehem Steel (now Mittal Steel) to demonstrate the effectiveness of using nickel aluminide intermetallic alloy rolls as part of an updated, energy-efficient, commercial annealing furnace system.

Development and Evaluation of Curriculum and Media to Train Part-Time Fire Service Instructors in Rural Areas.

ERIC Educational Resources Information Center

Kloss, Frank E.

The report briefly describes a project whose purpose was to provide guidance and training for rural volunteer fire chiefs and firefighters in Wisconsin to increase the knowledge and skills they use to protect lives and property. The training was provided by part-time instructors who taught and demonstrated the courses and curriculum to suit the…

Successful integration efforts in water quality from the integrated Ocean Observing System Regional Associations and the National Water Quality Monitoring Network

USGS Publications Warehouse

Ragsdale, R.; Vowinkel, E.; Porter, D.; Hamilton, P.; Morrison, R.; Kohut, J.; Connell, B.; Kelsey, H.; Trowbridge, P.

2011-01-01

The Integrated Ocean Observing System (IOOS??) Regional Associations and Interagency Partners hosted a water quality workshop in January 2010 to discuss issues of nutrient enrichment and dissolved oxygen depletion (hypoxia), harmful algal blooms (HABs), and beach water quality. In 2007, the National Water Quality Monitoring Council piloted demonstration projects as part of the National Water Quality Monitoring Network (Network) for U.S. Coastal Waters and their Tributaries in three IOOS Regional Associations, and these projects are ongoing. Examples of integrated science-based solutions to water quality issues of major concern from the IOOS regions and Network demonstration projects are explored in this article. These examples illustrate instances where management decisions have benefited from decision-support tools that make use of interoperable data. Gaps, challenges, and outcomes are identified, and a proposal is made for future work toward a multiregional water quality project for beach water quality.

Water quality success stories: Integrated assessments from the IOOS regional associations and national water quality monitoring network

USGS Publications Warehouse

Ragsdale, Rob; Vowinkel, Eric; Porter, Dwayne; Hamilton, Pixie; Morrison, Ru; Kohut, Josh; Connell, Bob; Kelsey, Heath; Trowbridge, Phil

2011-01-01

The Integrated Ocean Observing System (IOOS®) Regional Associations and Interagency Partners hosted a water quality workshop in January 2010 to discuss issues of nutrient enrichment and dissolved oxygen depletion (hypoxia), harmful algal blooms (HABs), and beach water quality. In 2007, the National Water Quality Monitoring Council piloted demonstration projects as part of the National Water Quality Monitoring Network (Network) for U.S. Coastal Waters and their Tributaries in three IOOS Regional Associations, and these projects are ongoing. Examples of integrated science-based solutions to water quality issues of major concern from the IOOS regions and Network demonstration projects are explored in this article. These examples illustrate instances where management decisions have benefited from decision-support tools that make use of interoperable data. Gaps, challenges, and outcomes are identified, and a proposal is made for future work toward a multiregional water quality project for beach water quality.

Fabrication of cylindrical micro-parts using synchronous rotary scan-projection lithography and chemical etching

NASA Astrophysics Data System (ADS)

Ito, Kaiki; Suzuki, Yuta; Horiuchi, Toshiyuki

2017-07-01

Lithographical patterning on the surface of a fine pipe with a thin wall is required for fabricating three-dimensional micro-parts. For this reason, a new exposure system for printing patterns on a cylindrical pipe by synchronous rotary scan-projection exposure was developed. Using the exposure system, stent-like resist patterns with a width of 251 μm were printed on a surface of stainless-steel pipe with an outer diameter of 2 mm. The exposure time was 30 s. Next, the patterned pipe was chemically etched. As a result, a stent-like mesh pipe with a line width of 230 μm was fabricated. It was demonstrated that the new method had a potential to be applied to fabrications of stent and other cylindrical micro-parts.

Experience report: Using formal methods for requirements analysis of critical spacecraft software

NASA Technical Reports Server (NTRS)

Lutz, Robyn R.; Ampo, Yoko

1994-01-01

Formal specification and analysis of requirements continues to gain support as a method for producing more reliable software. However, the introduction of formal methods to a large software project is difficult, due in part to the unfamiliarity of the specification languages and the lack of graphics. This paper reports results of an investigation into the effectiveness of formal methods as an aid to the requirements analysis of critical, system-level fault-protection software on a spacecraft currently under development. Our experience indicates that formal specification and analysis can enhance the accuracy of the requirements and add assurance prior to design development in this domain. The work described here is part of a larger, NASA-funded research project whose purpose is to use formal-methods techniques to improve the quality of software in space applications. The demonstration project described here is part of the effort to evaluate experimentally the effectiveness of supplementing traditional engineering approaches to requirements specification with the more rigorous specification and analysis available with formal methods.

NASA Advances Technologies for Additive Manufacturing of GRCop-84 Copper Alloy

NASA Technical Reports Server (NTRS)

Gradl, Paul; Protz, Chris

2017-01-01

The Low Cost Upper Stage Propulsion project has successfully developed and matured Selective Laser Melting (SLM) Fabrication of the NASA developed GRCop-84 copper alloy. Several parts have been printed in house and at a commercial vendor, and these parts have been successfully machined and have undergone further fabrication steps to allow hot-fire testing. Hot-fire testing has demonstrated parts manufactured with this technique can survive and perform well in the relevant environments for liquid rocket propulsion systems.

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

NASA Technical Reports Server (NTRS)

O’Neal, T. Derek

2016-01-01

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

Energy survey, study and report of hospitals in Michigan: Appendix A: Volume 2, Bay Medical Center, Bay City, Michigan: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-08-01

This study is part of a three-phased demonstration project to reduce energy consumption in hospitals through practical life-cycle, cost-effective modifications and alterations. Funds for the demonstration project are provided by the American Hospital Association (AHA), the Department of Energy (DOE), and the Department of Health and Human Services (DHHS). Two hospitals in Michigan were selected for the project, Bay Medical Center in Bay City and St. Mary's Hospital in Grand Rapids. The objectives of this study, which is funded by HHS, are to investigate and analyze energy usage of the facilities and to identify all life-cycle, cost-effective changes required tomore » effect a reduction in energy consumption.« less

Energy survey, study and report of hospitals in Michigan: Appendix A: Volume 1, Saint Mary's Hospital Grand Rapids, Michigan: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-08-01

This study is part of a three-phased demonstration project to reduce energy consumption in hospitals through practical life-cycle, cost-effective modifications and alterations. Funds for the demonstration project are provided by the American Hospital Association (AHA), the Department of Energy (DOE), and the Department of Health and Human Services (DHHS). Two hospitals in Michigan were selected for the project, Bay Medical Center in Bay City and St. Mary's Hospital in Ground Rapids. The objectives of this study, which is funded by HHS, are to investigate and analyze energy usage of the facilities and to identify all life-cycle, cost-effective changes required tomore » effect a reduction in energy consumption.« less

American Fuel Cell Bus Project Evaluation. Second Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, Leslie; Post, Matthew

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE'smore » National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.« less

Multi-Element Integrated Project Planning at Kennedy Space Center

NASA Technical Reports Server (NTRS)

Mullon, Robert

2008-01-01

This presentation demonstrates how the ASRC Scheduling team developed working practices to support multiple NASA and ASRC Project Managers using the enterprise capabilities of Primavera P6 and P6 Web Access. This work has proceeded as part of Kennedy Ground Systems' preparation for its transition from the Shuttle Program to the Constellation Program. The presenters will cover Primavera's enterprise-class capabilities for schedule development, integrated critical path analysis, and reporting, as well as advanced Primavera P6 Web Access tools and techniques for communicating project status.

WASTE MINIMIZATION OPPORTUNITY ASSESSMENT: PHILADELPHIA NAVAL SHIPYARD

EPA Science Inventory

The Waste Reduction Evaluation at Federal Sites (WREAFS) Program consists of a series of demonstration and evaluation projects for waste reduction conducted cooperatively by EPA and various parts of the Department of Defense (DOD), Department of Energy (DOE), and other Federal ag...

A PROJECTION OF URBAN GROWTH IN ATLANTA, GEORGIA

EPA Science Inventory

The U. S. Environmental Protection Agency's Regional Vulnerability Assessment Program(ReVA) is designed to develop and demonstrate approaches to identify the ecosystems at the greatest risk from regional population growth and economic activity. As part of this program, a cellular...

Freight information real-time system for transport (FIRST)

DOT National Transportation Integrated Search

2002-05-01

The FIRST Demonstration Project was funded and developed, in part, to provide unique solutions to freight transportation problems. FIRST is an Internet-based, real-time network that integrates many resources into a single, easy-to-use Web site on car...

Test of a 250 kVA Battery-Inverter System Micro-Grid: Cooperative Research and Development Final Report, CRADA Number CRD-11-460

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kramer, William; Martin, Greg; Lundstrom, Blake

Portland General Electric (PGE) is installing a 5-megawatt (MW) lithium-ion-based battery-inverter system (BIS) in Salem, Oregon, as part of the Pacific Northwest Smart Grid Demonstration Project. NREL will assist PGE in testing a 250-kilovolt-ampere (kVA) portion of the BIS in order to verify correct operation and minimize risk to subsequent demonstrations. In this project NREL will providetechnical support for the 250-kVA test and will work with PGE to write a test plan and evaluate the system in the lab before deployment in the field.

High Efficiency Water Heating Technology Development Final Report, Part II: CO 2 and Absorption-Based Residential Heat Pump Water Heater Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gluesenkamp, Kyle R.; Abdelaziz, Omar; Patel, Viral K.

2017-05-01

The two objectives of this project were to 1.demonstrate an affordable path to an ENERGY STAR qualified electric heat pump water heater (HPWH) based on low-global warming potential (GWP) CO 2 refrigerant, and 2.demonstrate an affordable path to a gas-fired absorption-based heat pump water heater with a gas energy factor (EF) greater than 1.0. The first objective has been met, and the project has identified a promising low-cost option capable of meeting the second objective. This report documents the process followed and results obtained in addressing these objectives.

Northrop Grumman Corporation's modified U.S. Navy F-5E Shaped Sonic Boom Demonstration (SSBD) aircraft flies over Lake Isabella, Calif., on Aug. 4, 2003

NASA Image and Video Library

2003-08-04

Northrop Grumman Corporation's modified U.S. Navy F-5E Shaped Sonic Boom Demonstration (SSBD) aircraft flies over Lake Isabella, California on Aug. 4, 2003. NASA Dryden provided range, air and ground data-gathering support for the SSBD project, which is part of DARPA's Quiet Supersonic Platform (QSP) program.

Single body parts are processed by individual neurons in the mouse dorsolateral striatum.

PubMed

Coffey, Kevin R; Nader, Miles; West, Mark O

2016-04-01

Interest in the dorsolateral striatum (DLS) has generated numerous scientific studies of its neuropathologies, as well as its roles in normal sensorimotor integration and learning. Studies are informed by knowledge of DLS functional organization, the guiding principle being its somatotopic afferent projections from primary somatosensory (S1) and motor (M1) cortices. The potential to connect behaviorally relevant function to detailed structure is elevated by mouse models, which have access to extensive genetic neuroscience tool kits. Remaining to be demonstrated, however, is whether the correspondence between S1/M1 corticostriatal terminal distributions and the physiological properties of DLS neurons demonstrated in rats and non-human primates exists in mice. Given that the terminal distribution of S1/M1 projections to the DLS in mice is similar to that in rats, we studied whether firing rates (FRs) of DLS neurons in awake, behaving mice are related to activity of individual body parts. MSNs exhibited robust, selective increases in FR during movement or somatosensory stimulation of single body parts. Properties of MSNs, including baseline FRs, locations, responsiveness to stimulation, and proportions of responsive neurons were similar to properties observed in rats. Future studies can be informed by the present demonstration that the mouse lateral striatum functions as a somatic sensorimotor sector of the striatum and appears to be a homolog of the primate putamen, as demonstrated in rats (Carelli and West, 1991). Copyright © 2016 Elsevier B.V. All rights reserved.

Experimental Demonstration of Frequency Regulation by Commercial Buildings – Part II: Results and Performance Evaluation

DOE PAGES

Vrettos, Evangelos; Kara, Emre Can; MacDonald, Jason; ...

2016-11-15

This paper is the second part of a two-part series presenting the results from an experimental demonstration of frequency regulation in a commercial building test facility. We developed relevant building models and designed a hierarchical controller for reserve scheduling, building climate control and frequency regulation in Part I. In Part II, we introduce the communication architecture and experiment settings, and present extensive experimental results under frequency regulation. More specifically, we compute the day-ahead reserve capacity of the test facility under different assumptions and conditions. Furthermore, we demonstrate the ability of model predictive control to satisfy comfort constraints under frequency regulation,more » and show that fan speed control can track the fast-moving RegD signal of the Pennsylvania, Jersey, and Maryland Power Market (PJM) very accurately. In addition, we discuss potential effects of frequency regulation on building operation (e.g., increase in energy consumption, oscillations in supply air temperature, and effect on chiller cycling), and provide suggestions for real-world implementation projects. Our results show that hierarchical control is appropriate for frequency regulation from commercial buildings.« less

Ceramic Technology for Advanced Heat Engines Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-08-01

The Ceramic Technology for Advanced Heat Engines Project was developed by the Department of Energy's Office of Transportation Systems (OTS) in Conservation and Renewable Energy. This project, part of the OTS's Advanced Materials Development Program, was developed to meet the ceramic technology requirements of the OTS's automotive technology programs. Significant accomplishments in fabricating ceramic components for the Department of Energy (DOE), National Aeronautics and Space Administration (NASA), and Department of Defense (DoD) advanced heat engine programs have provided evidence that the operation of ceramic parts in high-temperature engine environments is feasible. However, these programs have also demonstrated that additional researchmore » is needed in materials and processing development, design methodology, and data base and life prediction before industry will have a sufficient technology base from which to produce reliable cost-effective ceramic engine components commercially.« less

Vocational Rehabilitation in Juvenile Delinquency: A Planning Grant to Determine the Role of Vocational Rehabilitation in Juvenile Delinquency. Final Report. Research and Demonstration Project (July 1, 1963--June 30, 1964).

ERIC Educational Resources Information Center

Oklahoma State Board for Vocational Education, Stillwater. Rehabilitation Service Div.

This project developed from a need for knowledge and information concerning a problem of growing concern to most American communities and particularly those comprising metropolitan areas. Increasing evidence of disregard for law and order on the part of individuals of all ages, and especially teen-age children, points up the need for intelligent…

Facility Activation and Characterization for IPD Oxidizer Turbopump Cold-Flow Testing at NASA Stennis Space Center

NASA Technical Reports Server (NTRS)

Sass, J. P.; Raines, N. G.; Farner, B. R.; Ryan, H. M.

2004-01-01

The Integrated Powerhead Demonstrator (IPD) is a 250K lbf (1.1 MN) thrust cryogenic hydrogen/oxygen engine technology demonstrator that utilizes a full flow staged combustion engine cycle. The Integrated Powerhead Demonstrator (IPD) is part of NASA's Next Generation Launch Technology (NGLT) program, which seeks to provide safe, dependable, cost-cutting technologies for future space launch systems. The project also is part of the Department of Defense's Integrated High Payoff Rocket Propulsion Technology (IHPRPT) program, which seeks to increase the performance and capability of today s state-of-the-art rocket propulsion systems while decreasing costs associated with military and commercial access to space. The primary industry participants include Boeing-Rocketdyne and GenCorp Aerojet. The intended full flow engine cycle is a key component in achieving all of the aforementioned goals. The IPD Program achieved a major milestone with the successful completion of the IPD Oxidizer Turbopump (OTP) cold-flow test project at the NASA John C. Stennis Space Center (SSC) E-1 test facility in November 2001. A total of 11 IPD OTP cold-flow tests were completed. Following an overview of the NASA SSC E-1 test facility, this paper addresses the facility aspects pertaining to the activation and the cold-flow testing of the IPD OTP. In addition, some of the facility challenges encountered during the test project are addressed.

ICAM (Integrated Computer Aided Manufacturing) Conceptual Design for Computer-Integrated Manufacturing. Volume 1. Project Overview and Technical Summary

DTIC Science & Technology

1984-06-29

sheet metal, machined and composite parts and assembling the components into final pruJucts o Planning, evaluating, testing, inspecting and...Research showed that current programs were pursuing the design and demonstration of integrated centers for sheet metal, machining and composite ...determine any metal parts required and to schedule these requirements from the machining center. Figure 3-33, Planned Composite Production, shows

ABCGheritage project - promoting geotourism in northern Finland, northern Norway and the Kola Peninsula

NASA Astrophysics Data System (ADS)

Pihlaja, Jouni; Johansson, Peter; Lauri, Laura S.

2014-05-01

Nature tourism has been a growing business sector in the Barents area during the recent decades. With the purpose to develop nature tourism in a sustainable way, a cooperation project ABCGheritage - Arctic Biological, Cultural and Geological Heritage has been carried out. Project has received partial funding from the EU Kolarctic ENPI program. In the geoheritage part of the project the main activities were aimed to develop pro-environmental ways of geotourism in the area. The three main participants in the geoheritage part of the project are the Geological Survey of Finland, Northern Finland Office, the Geological Institute of the Kola Science Centre of the Russian Academy of Sciences and Bioforsk Soil and Environment from northeastern Norway. The duration of the project is 2012-2014 and most of the work has already been completed even if most of the results are not published yet. Totally ten different tasks have been implemented in the geological part of the project. The largest task has been the preparation of a geological outdoor map and guide book of the Khibiny Tundra locating in the central part of the Kola Peninsula. In Finland already 11 such maps have been published, and the experiences gained during their production have been used in this project, too. Geological heritage trails to the Khibiny Tundra have also been created and they will be drawn on the map. The second concrete result is the Barents Tour for Geotourist -guide, which will be published as a guide book, web pages and an exhibition. The route comprises ca 35 best geological demonstration sites along the circle route from northern Finland to northeastern Norway, from there to Kola Peninsula and then back to Finland. Information of the route will be available for all interested travelers. In addition to the geological outdoor map of the Khibiny Tundra and "Barents Tour for Geotourists"-guide, the primary outputs of the project are the geological nature trails on the field, geological demonstration sites with uniform signposts and educational data packages on geological heritage. The main target groups are pupils and teachers at schools, especially on elementary stage. Tourists and locals visiting protected and recreational areas and other heritage sites will also benefit from the results. Personnel working in education and tourism will get new targets and background data for their clients. Final beneficiaries are local inhabitants, entrepreneurs and companies through positive impact to local economy and communities.

Energy Systems Integration: Demonstrating Distributed Resource Communications

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-01

Overview fact sheet about the Electric Power Research Institute (EPRI) and Schneider Electric Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

US-75 ICM system design document : Dallas Integrated Corridor Management (ICM) demonstration project.

DOT National Transportation Integrated Search

2013-06-01

This System Design document for the US-75 Integrated Corridor Management (ICM) Program has been developed as part of the US Department of Transportation Integrated Corridor Management Initiative. The basic premise behind the ICM initiative is that in...

Curriculum Guide for Adult Education Teachers.

ERIC Educational Resources Information Center

Hammett, Earl Lee

This curriculum guide for teachers of adult education is divided into three parts. The first offers an overview of adult basic education, the teacher as counselor, testing and evaluation, instructional procedures--physical environment and classroom management, techniques providing variety in instruction--discussions, demonstrations, projects,…

Guidelines for NASA Missions to Engage the User Community as a Part of the Mission Life Cycle

NASA Astrophysics Data System (ADS)

Escobar, V. M.; Friedl, L.; Bonniksen, C. K.

2017-12-01

NASA continues to improve the Earth Science Directorate in the areas of thematic integration, stakeholder feedback and Project Applications Program tailoring for missions to transfer knowledge between scientists and projects. The integration of application themes and the implementation of application science activities in flight projects have evolved to formally include user feedback and stakeholder integration. NASA's new Flight Applied Science Program Guidelines are designed to bridge NASA Earth Science Directorates in Flight, Applied Sciences and Research and Development by agreeing to integrate the user community into mission life cycles. Thus science development and science applications will guide all new instruments launched by NASAs ESD. The continued integration with the user community has enabled socio-economic considerations into NASA Earth Science projects to advance significantly. Making users a natural part of mission science leverages future socio-economic impact research and provides a platform for innovative and more actionable product to be used in decision support systems by society. This presentation will give an overview of the new NASA Guidelines and provide samples that demonstrate how the user community can be a part of NASA mission designs.

How an impact plan can build on the success of your project - from proposal to legacy

NASA Astrophysics Data System (ADS)

Alexiou, Sofia

2017-04-01

Research Impact is often defined as the 'demonstrable contribution that excellent research makes to society and the economy'. Impact is important as it demonstrates the value of funding agencies' investment into science. Measuring impact is an essential part of project management, from proposal phase to output. However, impact can mean a range of things to different people and organisations. When applying for funding, it is critical to check and understand the type of impact recognised by the relevant funder and to consider opportunities for building in multiple benefits . In 2015, it was observed that the drive to 'get stricter on impact' had a direct effect on the evaluators' instructions and subsequent proposal ratings. As funding agencies are reshaping assessment processes and implementing new indicators of impact and new innovation actions, it is clear that a need to demonstrate performance, impact and added-value must be included within the proposal phase and executed throughout project lifetime.

Preliminary Radiation Analysis of the Total Ionizing Dose for the Resource Prospector Mission

NASA Technical Reports Server (NTRS)

Rojdev, Kristina; Tylka, Allan J.; Atwell, William

2015-01-01

NASA's Resource Prospector (RP) is a collaborative project between multiple centers and institutions to search for volatiles at the polar regions of the Moon as a potential resource for oxygen and propellant production. The mission is rated Class D and will be the first In-Situ Resource Utilization (ISRU) demonstration on the lunar surface and at the lunar poles. Given that this mission is rated Class D, the project is considering using commercial off the shelf (COTS) electronics parts to reduce cost. However, COTS parts can be more susceptible to space radiation than typical aerospace electronic parts and carry some additional risk. Thus, prior to parts selection, having a better understanding of the radiation environment can assist designers in the parts selection process. The focus of this paper is to provide a preliminary analysis of the radiation environment from launch, through landing on the surface, and some surface stay as an initial step in determining worst case mission doses to assist designers in screening out electronic parts that would not meet the potential dose levels experienced on this mission.

DEEPEGS and the IDDP, Focus on Reykjanes Demonstration

NASA Astrophysics Data System (ADS)

Ómar Friðleifsson, Guðmundur; Bogason, Sigurður G.; Ingólfsson, Hjalti P.; Vergnes, Pierre; Thorbjörnsson, Ingólfur Ö.; Peter-Borie, Mariane; Kohl, Tohmas; Gaucher, Emmanuel; Edelmann, Thomas; Bertani, Ruggero; Sæther, Sturla; Pálsson, Bjarni

2016-04-01

The DEEPEGS project is a demonstration project, supported by the European Commission, Horizon 2020. The goal is to demonstrate the feasibility of enhanced geothermal systems (EGS) for delivering energy from renewable resources in Europe. It is a four years project coordinated by HS Orka, Iceland, in cooperation with partners from Iceland, France, Germany, Italy, and Norway. The project will be testing stimulation technologies for EGS in deep wells in different geological settings, and intends to deliver new innovative solutions and models for wider deployments of EGS reservoirs with sufficient permeability to delivering significant amounts of geothermal power across Europe. The project will demonstrate advanced technologies in three types of geothermal reservoirs, (i) in high enthalpy resource beneath existing hydrothermal field at Reykjanes (volcanic environment with a saline fluid) with temperature up to 550°C and (ii) two very deep hydrothermal reservoirs in southern France with temperatures up to 220°C. The focus of the talk at EGU 2016 will be on the Icelandic part of the DEEPEGS project and its connection to the IDDP project in Iceland, and to the ICDP. The deep well at Reykjanes, identified as well IDDP-2, is expected to be completed in 2016. A 2.5 km deep production well will be refurbished and deepened to 5 km by HS Orka, Statoil and IDDP. After drilling the well it will be extensively tested for injectivity, and connection to the overlying conventional hydrothermal field, and subsequently flow tested for fluid chemistry and production properties. The DEEPEGS consortium is industry driven with five energy companies that will implement the project's goal through cross-fertilisation and sharing of knowledge. The companies are all highly experienced in energy production, and three of them are already delivering power to national grids from geothermal resources.

Northrop Grumman Corporation's modified U.S. Navy F-5E Shaped Sonic Boom Demonstration (SSBD) aircraft flies over the company's Palmdale, Calif. facilities on Aug. 2, 2003

NASA Image and Video Library

2003-08-02

Northrop Grumman Corporation's modified U.S. Navy F-5E Shaped Sonic Boom Demonstration (SSBD) aircraft flies over the company's Palmdale, California facilities on Aug. 2, 2003. NASA Dryden provided range, air and ground data-gathering support for the SSBD project, which is part of DARPA's Quiet Supersonic Platform (QSP) program.

UXO Detection and Characterization in the Marine Environment

DTIC Science & Technology

2009-12-01

10 Figure 8. A part of Ostrich Bay adjacent to the Naval Ammunition Depot Puget Sound during the period of its...large-scale demonstration focus on a marine geophysical magnetometry survey of Ostrich Bay adjacent to the Former Naval Ammunition Depot – Puget Sound ...The Puget Sound Demonstration was also supported by NAVFAC Northwest, the current manager of the site. The Navy Project Manager is Mr. Mark Murphy

US-75 ICM system as-built design : Dallas Integrated Corridor Management (ICM) demonstration project.

DOT National Transportation Integrated Search

2015-05-01

This As-Built document for the US-75 Integrated Corridor Management (ICM) Program has been developed as part of the US Department of Transportation Integrated Corridor Management Initiative. The basic premise behind the ICM initiative is that indepen...

Inorganic Reaction Mechanisms. Part I

ERIC Educational Resources Information Center

Cooke, D. O.

1976-01-01

Provides a collection of data on the mechanistic aspects of inorganic chemical reactions. Wherever possible includes procedures for classroom demonstration or student project work. The material covered includes gas phase reactions, reactions in solution, mechanisms of electron transfer, the reaction between iron III and iodine, and hydrolysis. (GS)

Ethanol Research : Alternative Fuels & Life-Cycle Engineering Program : November 29, 2006 to November 28, 2011

DOT National Transportation Integrated Search

2011-12-20

This report presents the results of the successful ethanol fuel demonstration program conducted from September 2007 to September 2010. This project was a part of the U.S. Department of Transportation (DOT) Alternative Fuels and Life Cycle Engineering...

Crawler Acquisition and Testing Demonstration Project Management Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

DEFIGH-PRICE, C.

2000-10-23

If the crawler based retrieval system is selected, this project management plan identifies the path forward for acquiring a crawler/track pump waste retrieval system, and completing sufficient testing to support deploying the crawler for as part of a retrieval technology demonstration for Tank 241-C-104. In the balance of the document, these activities will be referred to as the Crawler Acquisition and Testing Demonstration. During recent Tri-Party Agreement negotiations, TPA milestones were proposed for a sludge/hard heel waste retrieval demonstration in tank C-104. Specifically one of the proposed milestones requires completion of a cold demonstration of sufficient scale to support finalmore » design and testing of the equipment (M-45-03G) by 6/30/2004. A crawler-based retrieval system was one of the two options evaluated during the pre-conceptual engineering for C-104 retrieval (RPP-6843 Rev. 0). The alternative technology procurement initiated by the Hanford Tanks Initiative (HTI) project, combined with the pre-conceptual engineering for C-104 retrieval provide an opportunity to achieve compliance with the proposed TPA milestone M-45-03H. This Crawler Acquisition and Testing Demonstration project management plan identifies the plans, organizational interfaces and responsibilities, management control systems, reporting systems, timeline and requirements for the acquisition and testing of the crawler based retrieval system. This project management plan is complimentary to and supportive of the Project Management Plan for Retrieval of C-104 (RPP-6557). This project management plan focuses on utilizing and completing the efforts initiated under the Hanford Tanks Initiative (HTI) to acquire and cold test a commercial crawler based retrieval system. The crawler-based retrieval system will be purchased on a schedule to support design of the waste retrieval from tank C-104 (project W-523) and to meet the requirement of proposed TPA milestone M-45-03H. This Crawler Acquisition and Testing Demonstration project management plan includes the following: (1) Identification of acquisition strategy and plan to obtain a crawler based retrieval system; (2) Plan for sufficient cold testing to make a decision for W-523 and to comply with TPA Milestone M-45-03H; (3) Cost and schedule for path forward; (4) Responsibilities of the participants; and (5) The plan is supported by updated Level 1 logics, a Relative Order of Magnitude cost estimate and preliminary project schedule.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Walmart partnered with the U.S. Department of Energy (DOE) in 2009 to develop and demonstrate energy retrofits for existing buildings. The goal was to reduce energy consumption by at least 30% versus ASHRAE Standard 90.1-2007, as part of DOE's Commercial Building Partnerships (CBP) Program. The project presented here, the retrofit of a 213,000 square foot store in Centennial, Colorado, withefficiency measures across multiple building systems, is part of Walmart's ongoing environmental sustainability program, which originated in 2005.

Hearings Before the Select Committee on Nutrition and Human Needs of the United States Senate, Ninety-Second Congress, First Session, on Nutrition and Human Needs. Part 1--Review of the Results of the White House Conference on Food, Nutrition, and Health; Part 2--Kansas City, Kansas.

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. Senate Select Committee on Nutrition and Human Needs.

Contents of Part One include, in addition to the testimony of the witnesses called, such materials as: examples of citizen complaints, about the operation of school lunch programs; a report on the nutritional status of preschool Mexican-American farm children; a report on the Demonstration Migrant Nutrition Education Project, Edinburg, Texas; a…

Building on what you know.

PubMed

Patry, Leslie Anne

2006-02-01

The author undertook a project to support nurses participating in study groups as part of their strategy to prepare for the Canadian Nurses Association certification exams. Feedback was obtained from CNA certified nurses, study group participants and facilitators and other key stakeholders to develop a study group resource manual. CNA certification is a voluntary national nursing specialty credential that offers Canadian nurses the opportunity to demonstrate their knowledge and skills by meeting eligibility criteria and successfully writing an examination. Initially, development of a study group manual was the principal aim of the project; however, nurses' insights into their study group experiences became the focal point. Nurses recognized that being part of a study group was an effective learning strategy and a valuable networking experience. The author highlights nurses' study group experiences, describes the use of a nursing leadership conceptual model to frame the project and discusses the concept of continuing competence.

Quality improvement in childhood obesity management through the maintenance of certification process.

PubMed

Huang, Jeannie S; Chun, Stanford; Sandhu, Amanpreet; Terrones, Laura

2013-11-01

To assess the Health and Obesity: Prevention and Education (HOPE) Curriculum Project, a web-based clinician education program that promotes appropriate screening, prevention, and management of weight among youth by pediatric practitioners, based on the 2007 Expert Committee recommendations. The project currently provides Maintenance of Certification (MOC) Part 4 credit through the American Board of Pediatrics. Participants identified themselves to the HOPE MOC Part 4 program. Enrollees were required to complete all continuing medical education modules (10.5 hours). Knowledge acquisition and self-reported confidence levels related to screening, prevention, and management practices of pediatric obesity were measured using preknowledge and postknowledge questionnaires. Participants were also required to perform a quality improvement project and submit practice performance data from repeated medical chart reviews over time. Knowledge acquisition, self-efficacy, and practice performance data were analyzed using repeated-measures analyses. The 51 participants demonstrated significant improvements in knowledge acquisition and self-efficacy scores after viewing individual modules. In addition, participants demonstrated significant improvements in measured clinical compliance with recommended practices over time. Participation in the HOPE MOC Part 4 program appeared to improve knowledge acquisition, self-efficacy, and physician compliance with recommended practice recommendations for the screening, prevention, and management of pediatric obesity. Further data are required to determine whether such practice-based improvements translate into actual reduction in patient weight and/or reduction in health-related costs related to overweight and obesity in youth. Copyright © 2013 Mosby, Inc. All rights reserved.

The Ballistic Cart on an Incline Revisited.

ERIC Educational Resources Information Center

Serway, Raymond A.; And Others

1995-01-01

Presents the theory behind the mechanics demonstration that involves projecting a ball vertically upward from a ballistic cart moving along an inclined plane. The measured overshoot is believed to be due, in part, to the presence of rolling friction and the inertial properties of the cart wheels. (JRH)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

As part of a two-year project to demonstrate energy efficiency measures, renewable energy generation, and energy systems integration, the National Renewable Energy Laboratory (NREL) has identified advanced plug load controls as a promising technology for reducing energy use and related costs in the U.S. Navy's Naval Facilities Engineering Command (NAVFAC) office spaces.

Los Angeles congestion reduction demonstration (Metro ExpressLanes) program. National evaluation : transit system data test plan.

DOT National Transportation Integrated Search

1998-09-01

This flyer summarizes the activities and results of a preliminary human factors review for the Intelligent Vehicle Initiative (IVI) Program. As part of the IVI program, the Federal Highway Administration funded a project to investigate the human fact...

Multirate Flutter Suppression System Design for the Benchmark Active Controls Technology Wing. Part 1; Theory and Design Procedure

NASA Technical Reports Server (NTRS)

Mason, Gregory S.; Berg, Martin C.; Mukhopadhyay, Vivek

2002-01-01

To study the effectiveness of various control system design methodologies, the NASA Langley Research Center initiated the Benchmark Active Controls Project. In this project, the various methodologies were applied to design a flutter suppression system for the Benchmark Active Controls Technology (BACT) Wing. This report describes a project at the University of Washington to design a multirate suppression system for the BACT wing. The objective of the project was two fold. First, to develop a methodology for designing robust multirate compensators, and second, to demonstrate the methodology by applying it to the design of a multirate flutter suppression system for the BACT wing.

White Pine Co. Public School System Biomass Conversion Heating Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paul Johnson

The White Pine County School District and the Nevada Division of Forestry agreed to develop a pilot project for Nevada using wood chips to heat the David E. Norman Elementary School in Ely, Nevada. Consideration of the project was triggered by a ''Fuels for Schools'' grant that was brought to the attention of the School District. The biomass project that was part of a district-wide energy retrofit, called for the installation of a biomass heating system for the school, while the current fuel oil system remained as back-up. Woody biomass from forest fuel reduction programs will be the main sourcemore » of fuel. The heating system as planned and completed consists of a biomass steam boiler, storage facility, and an area for unloading and handling equipment necessary to deliver and load fuel. This was the first project of it's kind in Nevada. The purpose of the DOE funded project was to accomplish the following goals: (1) Fuel Efficiency: Purchase and install a fuel efficient biomass heating system. (2) Demonstration Project: Demonstrate the project and gather data to assist with further research and development of biomass technology; and (3) Education: Educate the White Pine community and others about biomass and other non-fossil fuels.« less

Evaluation of Additive Manufacturing for Composite Part Molds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duty, Chad E.; Springfield, Robert M.

2015-02-01

The ORNL Manufacturing Demonstration Facility (MDF) collaborated with Tru-Design to test the quality and durability of molds used for making fiber reinforced composites using additive manufacturing. The partners developed surface treatment techniques including epoxy coatings and machining to improve the quality of the surface finish. Test samples made using the printed and surface finished molds demonstrated life spans suitable for one-of-a-kind and low-volume applications, meeting the project objective.

NASA's In-Situ Resource Utilization Project: Current Accomplishments and Exciting Future Plans

NASA Technical Reports Server (NTRS)

Larson, William E.; Sanders, Gerald B.; Sacksteder, Kurt R.

2010-01-01

The utilization of Space resources has been identified in publications for over 40 years for its potential as a "game changing" technology for the human exploration of Space. It is called "game changing" because of the mass leverage possible when local resources at the exploration destination arc used to reduce or even eliminate resources that are brought from the Earth. NASA, under the Exploration Technology Development Program has made significant investments in the development of Space resource utilization technologies as a part of the In-Situ Resource Utilization (ISRU) project. Over the last four years, the ISRU project has taken what was essentially an academic topic with lots of experimentation but little engineering and produced near-full-scale systems that have been demonstrated. In 2008 & again in early 2010, systems that could produce oxygen from lunar soils (or their terrestrial analogs) were tested at a lunar analog site on a volcano in Hawaii. These demonstrations included collaborations with International Partners that made significant contributions to the tests. The proposed federal budget for Fiscal Year 2011 encourages the continued development and demonstration of ISRU. However it goes beyond what the project is currently doing and directs that the scope of the project be expanded to cover destinations throughout the inner solar system with the potential for night demonstrations. This paper will briefly cover the past accomplishments of the ISRU project then move to a di scussion of the plans for the project's future as NASA moves to explore a new paradigm for Space Exploration that includes orbital fuel depots and even refueling on other planetary bodies in the solar system.

Talking About The Smokes: a large-scale, community-based participatory research project.

PubMed

Couzos, Sophia; Nicholson, Anna K; Hunt, Jennifer M; Davey, Maureen E; May, Josephine K; Bennet, Pele T; Westphal, Darren W; Thomas, David P

2015-06-01

To describe the Talking About The Smokes (TATS) project according to the World Health Organization guiding principles for conducting community-based participatory research (PR) involving indigenous peoples, to assist others planning large-scale PR projects. The TATS project was initiated in Australia in 2010 as part of the International Tobacco Control Policy Evaluation Project, and surveyed a representative sample of 2522 Aboriginal and Torres Strait Islander adults to assess the impact of tobacco control policies. The PR process of the TATS project, which aimed to build partnerships to create equitable conditions for knowledge production, was mapped and summarised onto a framework adapted from the WHO principles. Processes describing consultation and approval, partnerships and research agreements, communication, funding, ethics and consent, data and benefits of the research. The TATS project involved baseline and follow-up surveys conducted in 34 Aboriginal community-controlled health services and one Torres Strait community. Consistent with the WHO PR principles, the TATS project built on community priorities and strengths through strategic partnerships from project inception, and demonstrated the value of research agreements and trusting relationships to foster shared decision making, capacity building and a commitment to Indigenous data ownership. Community-based PR methodology, by definition, needs adaptation to local settings and priorities. The TATS project demonstrates that large-scale research can be participatory, with strong Indigenous community engagement and benefits.

Demonstrate Energy Component of the Installation Master Plan Using Net Zero Installation Virtual Testbed

DTIC Science & Technology

2015-09-01

capabilities. Chapter 4 includes examples of their application and results. The tool has also been applied to EMP processes at Fort Leonard Wood , MO...such as solar photovoltaics, solar-thermal, wind energy, biomass ( wood chips, etc.), biogas, or synthetic gas need to be considered as part of the mix...this project Besides its use on pilot projects funded by ESTCP program, NZP is currently being used at Fort Leonard Wood , MO and several other

Demonstration of the Energy Component of the Installation Master Plan Using the Net Zero Energy Planner Tool

DTIC Science & Technology

2015-09-01

capabilities. Chapter 4 includes examples of their application and results. The tool has also been applied to EMP processes at Fort Leonard Wood , MO...such as solar photovoltaics, solar-thermal, wind energy, biomass ( wood chips, etc.), biogas, or synthetic gas need to be considered as part of the mix...this project Besides its use on pilot projects funded by ESTCP program, NZP is currently being used at Fort Leonard Wood , MO and several other

Servant leadership behaviors of aerospace and defense project managers and their relation to project success

NASA Astrophysics Data System (ADS)

Dominik, Michael T.

The success of a project is dependent in part on the skills, knowledge, and behavior of its leader, the project manager. Despite advances in project manager certifications and professional development, the aerospace and defense industry has continued to see highly visible and expensive project failures partially attributable to failures in leadership. Servant leadership is an emerging leadership theory whose practitioners embrace empowerment, authenticity, humility, accountability, forgiveness, courage, standing back, and stewardship, but has not yet been fully examined in the context of the project manager as leader. The objective of this study was to examine the relationship between servant leadership behaviors demonstrated by aerospace and defense project managers and the resulting success of their projects. Study participants were drawn from aerospace and defense oriented affinity groups from the LinkedInRTM social media web system. The participants rated their project managers using a 30-item servant leadership scale, and rated the success of their project using a 12-item project success scale. One hundred and fifteen valid responses were analyzed from 231 collected samples from persons who had worked for a project manager on an aerospace and defense project within the past year. The results of the study demonstrated statistically significant levels of positive correlation to project success for all eight servant leadership factors independently evaluated. Using multiple linear regression methods, the servant leadership factors of empowerment and authenticity were determined to be substantial and statistically significant predictors of project success. The study results established the potential application of servant leadership as a valid approach for improving outcomes of projects.

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

NASA Technical Reports Server (NTRS)

O'Neal, Derek

2016-01-01

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. The near-net shape DMLS parts have been delivered and final machining is underway. Fabrication of the traditionally manufactured hardware is also proceeding. Testing in liquid oxygen is planned for Q2 of FY2017. This topic explores the design of the turbopump along with fabrication and material testing of the DMLS hardware.

Close Range Calibration of Long Focal Length Lenses in a Changing Environment

NASA Astrophysics Data System (ADS)

Robson, Stuart; MacDonald, Lindsay; Kyle, Stephen; Shortis, Mark R.

2016-06-01

University College London is currently developing a large-scale multi-camera system for dimensional control tasks in manufacturing, including part machining, assembly and tracking, as part of the Light Controlled Factory project funded by the UK Engineering and Physical Science Research Council. In parallel, as part of the EU LUMINAR project funded by the European Association of National Metrology Institutes, refraction models of the atmosphere in factory environments are being developed with the intent of modelling and eliminating the effects of temperature and other variations. The accuracy requirements for both projects are extremely demanding, so accordingly improvements in the modelling of both camera imaging and the measurement environment are essential. At the junction of these two projects lies close range camera calibration. The accurate and reliable calibration of cameras across a realistic range of atmospheric conditions in the factory environment is vital in order to eliminate systematic errors. This paper demonstrates the challenge of experimentally isolating environmental effects at the level of a few tens of microns. Longer lines of sight promote the use and calibration of a near perfect perspective projection from a Kern 75mm lens with maximum radial distortion of the order of 0.5m. Coordination of a reference target array, representing a manufactured part, is achieved to better than 0.1mm at a standoff of 8m. More widely, results contribute to better sensor understanding, improved mathematical modelling of factory environments and more reliable coordination of targets to 0.1mm and better over large volumes.

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2014 CFR

2014-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2012 CFR

2012-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2011 CFR

2011-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2013 CFR

2013-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

10 CFR 600.122 - Payment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... codified at 31 CFR part 205. (b) Recipients will be paid in advance, provided they maintain or demonstrate... standards for fund control and accountability as established in § 600.121. Cash advances to a recipient... program or project. The timing and amount of cash advances shall be as close as is administratively...

Competency-Based Adult Education: A Guide to Classroom Management.

ERIC Educational Resources Information Center

Guglielmino, Lucy M.; And Others

Developed as part of a 310 Special Demonstration and Teacher Training Project undertaken at Brevard Community College in 1984-85, this training guide for new Competency-Based Adult Education (CBAE) teachers offers information on the CBAE concept, individualized instruction, selection of instructional materials, student orientation, and procedures.…

SERDP AND NRMRL SPONSOR FIELD TEST OF COSOLVENT-ENHANCED DNAPL REMOVAL

EPA Science Inventory

A field test of multicomponent cosolvent flooding for in-situ remediation of DNAPL source zones was conducted at the Dover National Test Site (DNTS) at Dover Air Force Base, Delaware, in July, 2001. The test was part of an Enhanced Source Removal (ESR) demonstration project fund...

Performance Based Counselor Certification.

ERIC Educational Resources Information Center

Bernknopf, Stan; Ware, William B.

For the past four years the Georgia Department of Education has been involved in a statewide effort to establish standards and procedures for certification of educational personnel based on competency demonstration. As part of this effort, a project was commissioned to develop a performance-based system for the certification of school counselors.…

Culinary Arts Hospitality Symposium Planning Guide.

ERIC Educational Resources Information Center

Borgie, Karen; Wang, Yeimei

This guide was developed as part of a project to standardize California's statewide culinary arts curriculum based on industry guidelines and standards. It details a process that California community colleges can use to plan a hospitality symposium that will accomplish the following objectives: provide students with a forum to demonstrate their…

Executive Management Leadership Institute: Research Results, Volume I.

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh. Div. of Planning and Research Services.

The Executive Management Leadership Institute (EMLI) is a comprehensive sequence of modules designed to support development of administrators in the North Carolina Community College System. As part of the EMLI, participants complete a project demonstrating skill in applying research to the tasks of administration. This report presents three…

10 CFR 784.11 - Bases for granting waivers.

Code of Federal Regulations, 2014 CFR

2014-01-01

....3 of this part. However, some examples where advance waivers might be appropriate are: (1) Cost... privately-sponsored research, development, or demonstration project; (3) Situations such as Work for Others..., and 784.6, if applicable, in order to best achieve the objectives set forth in § 784.3. For example...

10 CFR 784.11 - Bases for granting waivers.

Code of Federal Regulations, 2012 CFR

2012-01-01

....3 of this part. However, some examples where advance waivers might be appropriate are: (1) Cost... privately-sponsored research, development, or demonstration project; (3) Situations such as Work for Others..., and 784.6, if applicable, in order to best achieve the objectives set forth in § 784.3. For example...

10 CFR 784.11 - Bases for granting waivers.

Code of Federal Regulations, 2010 CFR

2010-01-01

....3 of this part. However, some examples where advance waivers might be appropriate are: (1) Cost... privately-sponsored research, development, or demonstration project; (3) Situations such as Work for Others..., and 784.6, if applicable, in order to best achieve the objectives set forth in § 784.3. For example...

10 CFR 784.11 - Bases for granting waivers.

Code of Federal Regulations, 2013 CFR

2013-01-01

....3 of this part. However, some examples where advance waivers might be appropriate are: (1) Cost... privately-sponsored research, development, or demonstration project; (3) Situations such as Work for Others..., and 784.6, if applicable, in order to best achieve the objectives set forth in § 784.3. For example...

10 CFR 784.11 - Bases for granting waivers.

Code of Federal Regulations, 2011 CFR

2011-01-01

....3 of this part. However, some examples where advance waivers might be appropriate are: (1) Cost... privately-sponsored research, development, or demonstration project; (3) Situations such as Work for Others..., and 784.6, if applicable, in order to best achieve the objectives set forth in § 784.3. For example...

Recycling America's Workers: Public and Private Approaches to Midcareer Retraining.

ERIC Educational Resources Information Center

Bendick, Marc, Jr.; Egan, Mary Lou

This working paper, part of a project on the applicability of the French training system in the United States, argues that a systematic national commitment to midcareer worker retraining is necessary for American prosperity and international economic competitiveness. Although findings of the early human capital theorists demonstrated that an…

Energy Systems Integration: Demonstrating the Grid Benefits of Connected Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Overview fact sheet about the Electric Power Research Institute (EPRI) and the University of Delaware Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

Research use of the AIDA www.2aida.org diabetes software simulation program: a review-part 1. decision support testing and neural network training.

PubMed

Lehmann, Eldon D

2003-01-01

The purpose of this two-part review is to overview research use of the AIDA diabetes software simulator. AIDA is a diabetes computer program that permits the interactive simulation of plasma insulin and blood glucose profiles for teaching, demonstration, and self-learning purposes. It has been made freely available, without charge, on the Internet as a noncommercial contribution to continuing diabetes education. Since its launch in 1996 over 300,000 visits have been logged at the main AIDA Website-www.2aida.org-and over 60,000 copies of the AIDA program have been downloaded free-of-charge. This review describes research projects and ventures, undertaken for the most part by other research workers in the diabetes computing field, that have made use of the freeware AIDA software. Relevant research work was identified in three main ways: (i) by personal (e-mail/written) communications from researchers, (ii) via the ISI Web of Science citation database to identify published articles that referred to AIDA-related papers, and (iii) via searches on the Internet. In a number of cases research students who had sought advice about AIDA, and diabetes computing in general, provided copies of their research dissertations/theses upon the completion of their projects. The two reviews highlight some of the many and varied research projects that have made use of the AIDA diabetes simulation software to date. A wide variety of diabetes computing topics have been addressed. In Part 1 of the review, these range from testing decision support prototypes to training artificial neural networks. In Part 2 of the review, issues surrounding dietary assessments, developing new diabetes models, and performance monitoring of closed-loop insulin delivery devices are considered. Overall, research projects making use of AIDA have been identified in Australia, Italy, South Korea, the United Kingdom, and the United States. These reviews confirm an unexpected but useful benefit of distributing medical software, like AIDA, for free via the Internet-demonstrating how it is possible to have a synergistic benefit with other researchers-facilitating their own research projects in related medical fields. The reviews highlight a variety of these projects that have benefited from the free availability of the AIDA diabetes software simulator. In a number of cases these other research projects simply would not have been possible without unrestricted access to the AIDA software and/or technical descriptions of its workings. In addition, some specific common themes begin to emerge from the research ventures that have been reviewed. These include the use of simulated blood glucose data from the AIDA program for preliminary computerlab-based testing of other decision support prototypes. Issues surrounding such use of simulated data for separate prototype testing are discussed further in Part 2 of the review.

Ion projection lithography: November 2000 status and sub-70-nm prospects

NASA Astrophysics Data System (ADS)

Kaesmaier, Rainer; Wolter, Andreas; Loeschner, Hans; Schunck, Stefan

2000-10-01

Among all next generation lithography (NGL) options Ion Projection Lithography (IPL) offers the smallest (particle) wavelength of 5x10- 5nm (l00keV Helium ions). Thus, 4x reduction ion-optics has diffraction limits <3nm even when using a numerical aperture as low as NAequals10-5. As part of the European MEDEA IPL project headed by Infineon Technologies wide field ion-optics have been designed by IMS- Vienna with predicted resolution of 50nm within a 12.5mm exposure field. The ion-optics part of the PDT tool (PDT-IOS) has been realized and assembled. In parallel to the PDT-IOS effort, at Leica Jena a test bench for a vertical vacuum 300mm-wafer stage has been realized. Operation of magnetic bearing supported stage movement has already been demonstrated. As ASML vacuum compatible optical wafer alignment system, with 3nm(3(sigma) ) precision demonstrated in air, has been integrated to this wafer test bench system recently. Parallel to the IPL tool development, Infineon Technologies Mask House and the Institute for Microelectronics Stuttgart are intensively working on the development of IPL stencil masks with success in producing 150mm and 200mm stencil masks as reported elsewhere. This paper is focused on information about the status of the PDT-IOS tool.

The TRAINS project: A case study in building a conversational planning agent

NASA Astrophysics Data System (ADS)

Allen, James F.; Schubert, Lenhart K.; Ferguson, George; Heeman, Peter; Hwang, Chung Hee; Kato, Tsuneaki; Light, Marc; Martin, Nathaniel G.; Miller, Bradford W.; Poesio, Massimo

1994-09-01

The TRAINS project is an effort to build a conversationally proficient planning assistant. A key part of the project is the construction of the TRAINS system, which provides the research platform for a wide range of issues in natural language understanding, mixed-initiative planning systems, and representing and reasoning about time, actions and events. Four years have not passed since the beginning of the project. Each year, we produced a demonstration system that focused on a dialog that illustrated particular aspects of our research. The commitment to building complete integrated systems is a significant overhead on the research, but we feel it is essential to guarantee that the results constitute real progress in the field. This paper describes the goals of the project, and our experience with the effort so far.

Downscaled Climate Change Projections for the Southern Colorado Plateau: Variability and Implications for Vegetation Changes

NASA Astrophysics Data System (ADS)

Garfin, G. M.; Eischeid, J. K.; Cole, K. L.; Ironside, K.; Cobb, N. S.

2008-12-01

Recent and rapid forest mortality in western North America and associated changes in fire frequency and area burned are among the chief concerns of ecosystem managers. These examples of climate change surprises demonstrate nonlinear and threshold ecosystem responses to increased temperatures and severe drought. A consistent management request from climate change adaptation workshops held during the last four years in the southwest U.S. is for region-specific estimates of climate and vegetation change, in order to provide guidance for management of federal and state forest, range, and riparian preserves and land holdings. Partly in response to these concerns, and partly in the interest of improving knowledge of potential ecosystem changes and their relationships with observed changes and changes demonstrated in the paleoecological record, we developed a set of integrated climate and ecosystem analyses. We selected five of twenty-two GCMs from the PCMDI archive of IPCC AR4 model runs, based on their approximations of observed critical seasonality for vegetation in the Southern Colorado Plateau (domain: 35°- 38°N, 114°-107°W), centered on the Four Corners states. We used three key seasons in our analysis, winter (November-March), pre-monsoon (May-June), and monsoon (July- September). Projections of monthly and seasonal temperature and precipitation from our five-model ensemble indicate steadily increasing temperatures in our region of interest during the twenty-first century. By 2050, the ensemble projects increases of 3.0°C during May and June, months critical for drought stress and tree mortality, and 4.5-5.0°C by 2090. Projected temperature changes for months during the heart of winter (December and January) are on the order of 2.5°C by 2050 and 3.0°C by 2090; such changes are likely to affect snow hydrology in middle to low elevations in the Southern Colorado Plateau. Summer temperature increases are on the order of 2.5°C (2050) and 4.0°C (2090). The most striking aspect of projections of future precipitation is steadily decreasing May-June precipitation during the twenty-first century. Though absolute precipitation during this season is small, declining moisture during the arid pre-monsoon will likely decrease soil moisture, and increase drought stress - consequently, increasing vegetation susceptibility the insect outbreaks and disease. Summer precipitation projections show considerable multi-decade variability, but no substantial trends. Winter precipitation shows little interannual variability and no strong trends. By 2090, annual precipitation is projected to decline by 1-5% across much of the region, with greater declines in the southern part of the domain and increases of 1-5% in the northwestern and northeastern parts of the domain. As part of a National Institute for Climate Change Research project, these projected changes will be input into a USDA-FS vegetation response model, in order to estimate species-specific responses to projected climate changes. We expect increasing temperatures, declining annual precipitation, and extreme declines in pre-monsoon season precipitation to generate significant redistribution of some plant species in the Southern Colorado Plateau.

Health and Environment Linked for Information Exchange (HELIX)-Atlanta: A CDC-NASA Joint Environmental Public Health Tracking Collaborative Project

NASA Technical Reports Server (NTRS)

Al-Hamdan, Mohammad; Luvall, Jeff; Crosson, Bill; Estes, Maury; Limaye, Ashutosh; Quattrochi, Dale; Rickman, Doug

2008-01-01

HELIX-Atlanta was developed to support current and future state and local EPHT programs to implement data linking demonstration projects which could be part of the CDC EPHT Network. HELIX-Atlanta is a pilot linking project in Atlanta for CDC to learn about the challenges the states will encounter. NASA/MSFC and the CDC are partners in linking environmental and health data to enhance public health surveillance. The use of NASA technology creates value added geospatial products from existing environmental data sources to facilitate public health linkages. Proving the feasibility of the approach is the main objective

North-South Corridor Demonstration Project: Ethical and Logistical Challenges in the Design of a Demonstration Study of Early Antiretroviral Treatment for Long Distance Truck Drivers along a Transport Corridor through South Africa, Zimbabwe, and Zambia

PubMed Central

Gomez, G. B.; Venter, W. D. F.; Lange, J. M. A.; Rees, H.; Hankins, C.

2013-01-01

Background. Long-distance truck drivers are at risk of acquiring and transmitting HIV and have suboptimal access to care. New HIV prevention strategies using antiretroviral drugs to reduce transmission risk (early antiretroviral therapy (ART) at CD4 count >350 cells/μL) have shown efficacy in clinical trials. Demonstration projects are needed to evaluate “real world” programme effectiveness. We present the protocol for a demonstration study to evaluate the feasibility, acceptability, and cost of an early ART intervention for HIV-positive truck drivers along a transport corridor across South Africa, Zimbabwe, and Zambia, as part of an enhanced strategy to improve treatment adherence and retention in care. Methods and Analysis. This demonstration study would follow an observational cohort of truck drivers receiving early treatment. Our mixed methods approach includes quantitative, qualitative, and economic analyses. Key ethical and logistical issues are discussed (i.e., choice of drug regimen, recruitment of participants, and monitoring of adherence, behavioural changes, and adverse events). Conclusion. Questions specific to the design of tailored early ART programmes are amenable to operational research approaches but present substantial ethical and logistical challenges. Addressing these in demonstration projects can inform policy decisions regarding strategies to reduce health inequalities in access to HIV prevention and treatment programmes. PMID:23606977

Benchmarking forensic mental health organizations.

PubMed

Coombs, Tim; Taylor, Monica; Pirkis, Jane

2011-04-01

This paper describes the forensic mental health forums that were conducted as part of the National Mental Health Benchmarking Project (NMHBP). These forums encouraged participating organizations to compare their performance on a range of key performance indicators (KPIs) with that of their peers. Four forensic mental health organizations took part in the NMHBP. Representatives from these organizations attended eight benchmarking forums at which they documented their performance against previously agreed KPIs. They also undertook three special projects which explored some of the factors that might explain inter-organizational variation in performance. The inter-organizational range for many of the indicators was substantial. Observing this led participants to conduct the special projects to explore three factors which might help explain the variability - seclusion practices, delivery of community mental health services, and provision of court liaison services. The process of conducting the special projects gave participants insights into the practices and structures employed by their counterparts, and provided them with some important lessons for quality improvement. The forensic mental health benchmarking forums have demonstrated that benchmarking is feasible and likely to be useful in improving service performance and quality.

Engaging and Empowering the National Park Service to apply Earth Observations to Management Decisions

NASA Astrophysics Data System (ADS)

Clayton, A.; Ross, K. W.; Crepps, G.; Childs-Gleason, L. M.; Ruiz, M. L.; Rogers, L.; Allsbrook, K. N.

2017-12-01

Since 2015, the NASA DEVELOP National Program has partnered with the National Park Service (NPS) engaging more than 120 program participants, working on over 22 projects across approximately 27 unique park units. These projects examined a variety of cultural and environmental concerns facing the NPS including landscape disturbance, invasive species mapping, archaeological site preservation, and water resources monitoring. DEVELOP, part of NASA's Applied Sciences' Capacity Building program, conducts 10-week feasibility projects which demonstrate the utility of NASA's Earth observations as an additional tool for decision-making processes. This presentation will highlight several of these projects and discuss the progress of capacity building working with individual, regional, and institutional elements within the National Park Service.

Trend analyses of sediment data for the DEC project

USGS Publications Warehouse

Rebich, Richard Allen

1995-01-01

Daily stream discharge, suspended-sediment concentration, and suspended-sediment discharge data were collected at eight sites in six watersheds of the Demonstration Erosion Control project in the Yazoo River Basin in north-central Mississippi during the period July 1985 through September 1991. The project is part of an ongoing interagency program of planning, design, construction, monitoring, and evaluation to alleviate flooding, erosion, sedimentation, and water-quality problems for watersheds located in the bluff hills upstream of the Mississippi River alluvial plain. This paper presents preliminary results of trend analyses for stream discharge and sediment data for the eight project sites. More than 550 stream discharge measurements and 20,000 suspended-sediment samples have been collected at the eight sites since 1985.

PRESS40: a project for involving students in active seismic risk mitigation

NASA Astrophysics Data System (ADS)

Barnaba, Carla; Contessi, Elisa; Rosa Girardi, Maria

2016-04-01

To memorialize the anniversary of the 1976 Friuli earthquake, the Istituto Statale di Istruzione Superiore "Magrini Marchetti" in Gemona del Friuli (NE Italy), with the collaboration of the Istituto Nazionale di Oceanografia e di Geofisica Sperimentale (OGS), has promoted the PRESS40 Project (Prevenzione Sismica nella Scuola a 40 anni dal terremoto del Friuli, that in English sounds like "Seismic Prevention at School 40 years later the Friuli earthquake"). The project has developed in the 2015-2016 school year, starting from the 40th anniversary of the Friuli earthquake, and it aims to disseminate historical memory, seismic culture and awareness of seismic safety in the young generations, too often unconscious of past experiences, as recent seismic hazard perception tests have demonstrated. The basic idea of the PRESS40 Project is to involve the students in experimental activities to be active part of the seismic mitigation process. The Project is divided into two main parts, the first one in which students learn-receive knowledge from researchers, and the second one in which they teach-bring knowledge to younger students. In the first part of the project, 75 students of the "Magrini Marchetti" school acquired new geophysical data, covering the 23 municipalities from which they come from. These municipalities represent a wide area affected by the 1976 Friuli earthquake. In each locality a significant site was examined, represented by a school area. At least, 127 measurements of ambient noise have been acquired. Data processing and interpretation of all the results are still going on, under the supervision of OGS researchers.The second part of the project is planned for the early spring, when the students will present the results of geophysical survey to the younger ones of the monitored schools and to the citizens in occasion of events to commemorate the 40th anniversary of the Friuli earthquake.

EU demonstration project for separate discharge and treatment of urine, faeces and greywater--part II: cost comparison of different sanitation systems.

PubMed

Oldenburg, M; Peter-Fröhlich, A; Dlabacs, C; Pawlowski, L; Bonhomme, A

2007-01-01

The experience from the EU demonstration project was used for a cost analysis of different sanitation systems with regard to nutrient recycling. The analysis was made for an existing residential area, for which the different sanitation systems have been applied. The cost calculations were made for a lifetime of 50 years. The multiple sewer systems cause higher investment costs, mainly for the installation of the additional facilities; the investment costs for the treatment are lower. The cost analysis did not prove lower costs for the new sanitation concepts in this special case in comparison with the conventional system. Economic benefits are demonstrated for the operation costs. The result will be reinforced by the consideration of an increase of the energy costs. The revenues for the nutrient related products have only a very small impact on the result.

NASA Systems Autonomy Demonstration Project - Development of Space Station automation technology

NASA Technical Reports Server (NTRS)

Bull, John S.; Brown, Richard; Friedland, Peter; Wong, Carla M.; Bates, William

1987-01-01

A 1984 Congressional expansion of the 1958 National Aeronautics and Space Act mandated that NASA conduct programs, as part of the Space Station program, which will yield the U.S. material benefits, particularly in the areas of advanced automation and robotics systems. Demonstration programs are scheduled for automated systems such as the thermal control, expert system coordination of Station subsystems, and automation of multiple subsystems. The programs focus the R&D efforts and provide a gateway for transfer of technology to industry. The NASA Office of Aeronautics and Space Technology is responsible for directing, funding and evaluating the Systems Autonomy Demonstration Project, which will include simulated interactions between novice personnel and astronauts and several automated, expert subsystems to explore the effectiveness of the man-machine interface being developed. Features and progress on the TEXSYS prototype thermal control system expert system are outlined.

CERN@school: demonstrating physics with the Timepix detector

NASA Astrophysics Data System (ADS)

Whyntie, T.; Bithray, H.; Cook, J.; Coupe, A.; Eddy, D.; Fickling, R. L.; McKenna, J.; Parker, B.; Paul, A.; Shearer, N.

2015-10-01

This article shows how the Timepix hybrid silicon pixel detector, developed by the Medipix2 Collaboration, can be used by students and teachers alike to demonstrate some key aspects of any well-rounded physics curriculum with CERN@school. After an overview of the programme, the detector's capabilities for measuring and visualising ionising radiation are examined. The classification of clusters - groups of adjacent pixels - is discussed with respect to identifying the different types of particles. Three demonstration experiments - background radiation measurements, radiation profiles and the attenuation of radiation - are described; these can used as part of lessons or as inspiration for independent research projects. Results for exemplar data-sets are presented for reference, as well as details of ongoing research projects inspired by these experiments. Interested readers are encouraged to join the CERN@school Collaboration and so contribute to achieving the programme's aim of inspiring the next generation of scientists and engineers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sturgeon, J I

This volume relates primarily to Time-of-Day rates standard, PURPA IB(d)3, and deals with the content and methods of providing rate and conservation information to customers when Time-of-Day rates are used. Information to customers in the Demonstration and Pilot Projects fell mainly into four categories: administrative communications; explanations of new rate structures; information and advice on load management; and facts, recommendations and encouragements about energy conservation and end-use improvement. Administrative communications were about such matters as the existence of Projects, their funding, their periods of performance, the selection of their test customers, conditions of participation, procedural changes during the tests, andmore » the time and conditions of ending the tests. These communications were important to good customer cooperation. All Demonstration Projects devoted considerable effort to the crucial task of clearly explaining the rationale of Time-of-Use (TOU) pricing and the test rate structures. The Projects then presented the concept of TOU pricing as a means of (a) fairly charging customers the true cost of their electricity and (b) rewarding them for shifting consumption to times when costs are less. For the most part, Demonstration Projects gave specific information on the individual customer's own rate structure and none on any others that were under test. The information was presented in face-to-face interviews, group presentations, television, radio, and print media, and traveling exhibits. The results are evaluated. (LCL)« less

Dynamic Evaluation of CMAQ Part II: Evaluation of relative response factor metrics for ozone attainment demonstrations

EPA Science Inventory

The U.S. Environmental Protection Agency provides guidelines on the use of air quality models for projecting whether an emission reduction strategy will lead to future pollutant levels that are at or below the National Ambient Air Quality Standards (NAAQS). The EPA's guidance doc...

Field and laboratory investigation of warm mix asphalt in Texas.

DOT National Transportation Integrated Search

2010-07-01

During the first half of this research study, TxDOT had only placed 1000 tons of warm mix asphalt : (WMA) as part of a demonstration project. By the end of this three year study, TxDOT had placed more : than 1,000,000 tons of WMA and allowed its use ...

A Knowledge Development Plan for Youth Initiatives, Fiscal 1979.

ERIC Educational Resources Information Center

Employment and Training Administration (DOL), Washington, DC. Office of Youth Programs.

This report summarizes the past, present, and future activities of the Knowledge Development Plan for Youth Initiatives, which is being developed and implemented as part of the Youth Employment and Demonstration Projects Act (YEDPA). First, a framework for the plan is given, covering the aims of the fiscal 1978 and 1979 activities which stress…

Laboratory and field testing of an accelerated bridge construction demonstration bridge : US Highway 6 bridge over Keg Creek : tech transfer summary.

DOT National Transportation Integrated Search

2013-04-01

To address the need for the development of a fast, repeatable, and dependable way to replace typical bridges across the country, the Transportation Research Board (TRB) developed project R04, Innovative Designs for Rapid Renewal, as part of the...

Intermittent and Flexible Work Schedules and Welfare Mothers' Employment. Phase 2.

ERIC Educational Resources Information Center

Franklin, David S.

The project worked closely and supportively with California welfare mothers, helping them find suitable employment which meshed with their parenting functions, to demonstrate and test the impact of flexible work schedules and to determine whether business and industry could provide flexibly scheduled work (part-time, temporary, or intermittent).…

Literature Ladders: Linking Books and Internet Resources.

ERIC Educational Resources Information Center

Lamb, Annette

2001-01-01

Describes Literature Learning Ladders, a project that uses books for children and young adults as the focal point for technology-rich thematic activities. Explains the use of Internet Web sites to find book information as well as sties that demonstrate how resources can be used as part of technology-based classroom activities. (LRW)

Automated Work Packages Prototype: Initial Design, Development, and Evaluation. Light Water Reactor Sustainability Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna Helene; Ahmad Al Rashdan; Le Blanc, Katya Lee

The goal of the Automated Work Packages (AWP) project is to demonstrate how to enhance work quality, cost management, and nuclear safety through the use of advanced technology. The work described in this report is part of the digital architecture for a highly automated plant project of the technical program plan for advanced instrumentation, information, and control (II&C) systems technologies. This report addresses the DOE Milestone M2LW-15IN0603112: Describe the outcomes of field evaluations/demonstrations of the AWP prototype system and plant surveillance and communication framework requirements at host utilities. A brief background to the need for AWP research is provided, thenmore » two human factors field evaluation studies are described. These studies focus on the user experience of conducting a task (in this case a preventive maintenance and a surveillance test) while using an AWP system. The remaining part of the report describes an II&C effort to provide real time status updates to the technician by wireless transfer of equipment indications and a dynamic user interface.« less

Assessing Motivations and Use of Online Citizen Science Astronomy Projects

NASA Astrophysics Data System (ADS)

Nona Bakerman, Maya; Buxner, Sanlyn; Bracey, Georgia; Gugliucci, Nicole

2018-01-01

The exponential proliferation of astronomy data has resulted in the need to develop new ways to analyze data. Recent efforts to engage the public in the discussion of the importance of science has led to projects that are aimed at letting them have hands-on experiences. Citizen science in astronomy, which has followed the model of citizen science in other scientific fields, has increased in the number and type of projects in the last few years and poses captivating ways to engage the public in science.The primary feature of this study was citizen science users’ motivations and activities related to engaging in astronomy citizen science projects. We report on participants’ interview responses related to their motivations, length and frequency of engagement, and reasons for leaving the project. From May to October 2014, 32 adults were interviewed to assess their motivations and experiences with citizen science. In particular, we looked at if and how motivations have changed for those who have engaged in the projects in order to develop support for and understandparticipants of citizen science. The predominant reasons participants took part in citizen science were: interest, helping, learning or teaching, and being part of science. Everyone interviewed demonstrated an intrinsic motivation to do citizen science projects.Participants’ reasons for ending their engagement on any given day were: having to do other things, physical effects of the computer, scheduled event that ended, attention span or tired, computer or program issues. A small fraction of the participants also indicated experiencing negative feedback. Out of the participants who no longer took part in citizen science projects, some indicated that receiving negative feedback was their primary reason and others reported the program to be frustrating.Our work is helping us to understand participants who engage in online citizen science projects so that researchers can better design projects to meet their needs and develop support materials and incentives to encourage more participation.

Test and Demonstration Assets of New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This document was developed by the Arrowhead Center of New Mexico State University as part of the National Security Preparedness Project (NSPP), funded by a DOE/NNSA grant. The NSPP has three primary components: business incubation, workforce development, and technology demonstration and validation. The document contains a survey of test and demonstration assets in New Mexico available for external users such as small businesses with security technologies under development. Demonstration and validation of national security technologies created by incubator sources, as well as other sources, are critical phases of technology development. The NSPP will support the utilization of an integrated demonstrationmore » and validation environment.« less

The Thalamocortical Projection Systems in Primate: An Anatomical Support for Multisensory and Sensorimotor Interplay

PubMed Central

Cappe, Céline; Morel, Anne; Barone, Pascal

2009-01-01

Multisensory and sensorimotor integrations are usually considered to occur in superior colliculus and cerebral cortex, but few studies proposed the thalamus as being involved in these integrative processes. We investigated whether the organization of the thalamocortical (TC) systems for different modalities partly overlap, representing an anatomical support for multisensory and sensorimotor interplay in thalamus. In 2 macaque monkeys, 6 neuroanatomical tracers were injected in the rostral and caudal auditory cortex, posterior parietal cortex (PE/PEa in area 5), and dorsal and ventral premotor cortical areas (PMd, PMv), demonstrating the existence of overlapping territories of thalamic projections to areas of different modalities (sensory and motor). TC projections, distinct from the ones arising from specific unimodal sensory nuclei, were observed from motor thalamus to PE/PEa or auditory cortex and from sensory thalamus to PMd/PMv. The central lateral nucleus and the mediodorsal nucleus project to all injected areas, but the most significant overlap across modalities was found in the medial pulvinar nucleus. The present results demonstrate the presence of thalamic territories integrating different sensory modalities with motor attributes. Based on the divergent/convergent pattern of TC and corticothalamic projections, 4 distinct mechanisms of multisensory and sensorimotor interplay are proposed. PMID:19150924

Southern Regional Center for Lightweight Innovative Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Paul T.

The Southern Regional Center for Lightweight Innovative Design (SRCLID) has developed an experimentally validated cradle-to-grave modeling and simulation effort to optimize automotive components in order to decrease weight and cost, yet increase performance and safety in crash scenarios. In summary, the three major objectives of this project are accomplished: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantifymore » microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios. In this final report, we divided the content into two parts: the first part contains the development of building blocks for the project, including materials and process models, process-structure-property (PSP) relationship, and experimental validation capabilities; the second part presents the demonstration task for Mg front-end work associated with USAMP projects.« less

Advanced Planning and Scheduling Initiative- MrSpock Aims for Xmas

NASA Astrophysics Data System (ADS)

Steel, R.; Niezette, M.; Cesta, A.; Fratini, S.; Oddi, A.; Cortellessa, G.; Rasconi, R.; Verfaillie, G.; Pralet, C.; Lavagna, M.; Brambilla, A.; Castellini, F.; Donati, A.; Policella, N.

2009-09-01

This paper will outline the framework and tools developed under the Advanced Planning and Schedule Initiative (APSI) study performed by VEGA for the European Space Agency in collaboration with three academic institutions, ISTC-CNR, ONERA, and Politecnico di Milano. We will start by illustrating the background history to APSI and why it was needed, giving a brief summary of all the partners within the project and the roles they played within it. We will then take a closer look at what the APSI study actually consisted of, showing the techniques that were used and illustrating the framework that was developed within the scope of the project. This will be followed by an elaboration on the three demonstration test scenarios that have been developed as part of the project to validated the framework and demonstrate in an operational environment its applicability, illustrating the re-use and synergies between the three cases along the way. We will finally conclude with a brief summary and outline future directions to be further investigated and expanded on within the context of the work performed within the project.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kisner, Roger A; Melin, Alexander M; Burress, Timothy A

The overall project objective is to demonstrate improved reliability and increased performance made possible by deeply embedding instrumentation and controls (I&C) in nuclear power plant components. The project is employing a highly instrumented canned rotor, magnetic bearing, fluoride salt pump as its I&C technology demonstration vehicle. The project s focus is not primarily on pump design, but instead is on methods to deeply embed I&C within a pump system. However, because the I&C is intimately part of the basic millisecond-by-millisecond functioning of the pump, the I&C design cannot proceed in isolation from the other aspects of the pump. The pumpmore » will not function if the characteristics of the I&C are not embedded within the design because the I&C enables performance of the basic function rather than merely monitoring quasi-stable performance. Traditionally, I&C has been incorporated in nuclear power plant (NPP) components after their design is nearly complete; adequate performance was obtained through over-design. This report describes the progress and status of the project and provides a conceptual design overview for the embedded I&C pump.« less

Trans-Pacific Astronomy Experiment Project Status

NASA Technical Reports Server (NTRS)

Hsu, Eddie

2000-01-01

The Trans-Pacific Astronomy Experiment is Phase 2 of the Trans-Pacific High Data Rate Satcom Experiments following the Trans-Pacific High Definition Video Experiment. It is a part of the Global Information Infrastructure-Global Interoperability for Broadband Networks Project (GII-GIBN). Provides global information infrastructure involving broadband satellites and terrestrial networks and access to information by anyone, anywhere, at any time. Collaboration of government, industry, and academic organizations demonstrate the use of broadband satellite links in a global information infrastructure with emphasis on astronomical observations, collaborative discussions and distance learning.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heroux, Michael Allen; Marker, Bryan

This report summarizes the progress made as part of a one year lab-directed research and development (LDRD) project to fund the research efforts of Bryan Marker at the University of Texas at Austin. The goal of the project was to develop new techniques for automatically tuning the performance of dense linear algebra kernels. These kernels often represent the majority of computational time in an application. The primary outcome from this work is a demonstration of the value of model driven engineering as an approach to accurately predict and study performance trade-offs for dense linear algebra computations.

Model Checking Verification and Validation at JPL and the NASA Fairmont IV and V Facility

NASA Technical Reports Server (NTRS)

Schneider, Frank; Easterbrook, Steve; Callahan, Jack; Montgomery, Todd

1999-01-01

We show how a technology transfer effort was carried out. The successful use of model checking on a pilot JPL flight project demonstrates the usefulness and the efficacy of the approach. The pilot project was used to model a complex spacecraft controller. Software design and implementation validation were carried out successfully. To suggest future applications we also show how the implementation validation step can be automated. The effort was followed by the formal introduction of the modeling technique as a part of the JPL Quality Assurance process.

The Mars Technology Program

NASA Technical Reports Server (NTRS)

Hayati, Samad A.

2002-01-01

Future Mars missions require new capabilities that currently are not available. The Mars Technology Program (MTP) is an integral part of the Mars Exploration Program (MEP). Its sole purpose is to assure that required technologies are developed in time to enable the baselined and future missions. The MTP is a NASA-wide technology development program managed by JPL. It is divided into a Focused Program and a Base Program. The Focused Program is tightly tied to the proposed Mars Program mission milestones. It involves time-critical deliverables that must be developed in time for infusion into the proposed Mars 2005, and, 2009 missions. In addition a technology demonstration mission by AFRL will test a LIDAR as part of a joint NASNAFRL experiment. This program bridges the gap between technology and projects by vertically integrating the technology work with pre-project development in a project-like environment with critical dates for technology infusion. A Base Technology Program attacks higher riskhigher payoff technologies not in the critical path of missions.

Integrating family planning with other social services.

PubMed

Bernales, E H

1982-01-01

Family planning outreach workers in the 43 municipalities of Iloilo Province, Western Visayas, the Philippines, have provided their communities with health, nutrition, educational, and agricultural services since 1973, when the Provincial Development Staff (PDS) began attempting to integrate services. The early work of the PDS was aided by the launching of the National Population and Family Planning Outreach Project in rural areas in 1976 and the creation of the Provincial Population Office (PPO) in 1977. 43% of the Outreach Project cost is borne by the local government, with the Commission on Population covering the rest. It is anticipated that the local goverment will eventually absorb the full cost. The Outreach officers have become an integral part of the planning body of the provincial government, largely due to the creation of the Provincial Consultative Committee on Population (PCCP) in 1979. The PCCP, composed of 22 governmental and private agencies involved in population-related activities, is charged with implementing the national population program in order to utilize all possible resources for provincial development. Its Integrated Provincial Population Plan has become part of the total provincial development plan. The Municipal Population Planning Actions Teams, whose functions are patterned on those of the PCCPs, further strengthen local planning at the municipal level. Full-Time Outreach Workers participate as well in planning at the barangay level. The various community-based projects initiated by the Outreach staff in Iloilo demonstrate a concern with making the population program responsive to the immediate needs of the provincial population. Organizations which teach better farming methods and undertake community projects emphasize local initiative and solutions to problems, and demonstrate the committment of population workers to broader development efforts. Outreach workers are involved in primary health care, social service delivery, income generating projects, and other activities even in backward and inaccessible areas.

Military housing foam application and analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Torres, J. J.

2012-03-01

Sandia and Forest City have established a Cooperative Research and Development Agreement (CRADA), the partnership provides a unique opportunity to take technology research and development from demonstration to application in sustainable communities. This project consists of two activities conducted in Hawaii that focus on performance, integration and application of energy saving technologies. Hawaii has many energy challenges, making this location an excellent testbed for these activities. Under this project, spray foam technology was applied at military housing on Oahu and the consumption data collected. A cost benefit and operational analysis of the foam was completed. The second phase of thismore » project included design, integration, and analysis of photovoltaic systems at a military community on Oahu. This phase of the project was conducted as part of Forest City's second Solar America Showcase Award.« less

X-43C Plans and Status

NASA Technical Reports Server (NTRS)

Moses, Paul L.

2003-01-01

X-43C Project is a hypersonic flight demonstration being executed as a collaboration between the National Aeronautics and Space Administration (NASA) and the United States Air Force (USAF). X-43C will expand the hypersonic flight envelope for air breathing engines beyond the history making efforts of the Hyper-X Program (X-43A). X-43C will demonstrate sustained accelerating flight during three flight tests of expendable X-43C Demonstrator Vehicles (DVs). The approximately 16-foot long X-43C DV will be boosted to the starting test conditions, separate from the booster, and accelerate from Mach 5 to Mach 7 under its own power and autonomous control. The DVs are to be powered by a liquid hydrocarbon-fueled, fuel-cooled, dual-mode, airframe integrated scramjet engine system developed under the USAF HyTech Program. The Project is managed by NASA Langley Research Center as part of NASA s Next Generation Launch Technology Program. Flight tests will be conducted by NASA Dryden Flight Research Center over water off the coast of California in the Pacific Test Range. The NASA/USAF/industry project is a natural extension of the Hyper-X Program (X-43A), which will demonstrate short duration ( 10 seconds) gaseous hydrogen-fueled scramjet powered flight at Mach 7 and Mach 10 using a heavyweight, largely heat sink construction, experimental engine. The X-43C Project will demonstrate sustained accelerating flight from Mach 5 to Mach 7 ( 4 minutes) using a flight-weight, fuel-cooled, scramjet engine powered by much denser liquid hydrocarbon fuel. The X-43C DV design flows from integrating USAF HyTech developed engine technologies with a NASA Air Breathing Launch Vehicle accelerator-class configuration and Hyper-X heritage vehicle systems designs. This paper describes the X-43C Project and provides background for NASA s current hypersonic flight demonstration efforts.

FIELD DEMONSTRATION OF PERVAPORATION FOR THE SEPARATION OF VOLATILE ORGANIC COMPOUNDS FROM A SURFACTANT-BASED SOIL REMEDIATION FLUID

EPA Science Inventory

As part of a Department of Defense project, the US Environmental Protection Agency was responsible for designing, building and field operating a pilot-scale pervaporation unit. The field site ws an active dry cleaning facility on the grounds of Marine Corps Base Camp Lejeune in J...

School Nurses' Role in Asthma Management, School Absenteeism, and Cost Savings: A Demonstration Project

ERIC Educational Resources Information Center

Rodriguez, Eunice; Rivera, Diana Austria; Perlroth, Daniella; Becker, Edmund; Wang, Nancy Ewen; Landau, Melinda

2013-01-01

Background: With increasing budget cuts to education and social services, rigorous evaluation needs to document school nurses' impact on student health, academic outcomes, and district funding. Methods: Utilizing a quasi-experimental design, we evaluated outcomes in 4 schools with added full-time nurses and 5 matched schools with part-time nurses…

DESIGN AND TESTING OF SUB-SLAB DEPRESSURIZATION FOR RADON MITIGATION IN NORTH FLORIDA HOUSES - PART I. PERFORMANCE AND DURABILITY - VOLUME 2. DATA APPENDICES

EPA Science Inventory

The report gives results of a demonstration/research project to evaluate sub-slab depressurization (SSD) techniques for radon mitigation in North Florida where the housing stock is primarily slab-on-grade and the sub-slab medium typically consists of native soil and sand. Objecti...

DESIGN AND TESTING OF SUB-SLAB DEPRESSURIZATION FOR RADON MITIGATION IN NORTH FLORIDA HOUSES - PART I. PERFORMANCE AND DURABILITY - VOLUME 1. TECHNICAL REPORT

EPA Science Inventory

The report gives results of a demonstration/research project to evaluate sub-slab depressurization (SSD) techniques for radon mitigation in North Florida where the housing stock is primarily slab-on-grade and the sub-slab medium typically consists of native soil and sand. Objecti...

Testing and Demonstrating Speaker Verification Technology in Iraqi-Arabic as Part of the Iraqi Enrollment Via Voice Authentication Project (IEVAP) in Support of the Global War on Terrorism (GWOT)

DTIC Science & Technology

2007-09-01

Australian/New Zealand English, Canadian French, Cantonese , European French, German, Italian, Japanese, Jordanian Arabic, Mandarin, Portuguese...Environment Within the congruence model, the environment “includes people, other organizations, social and economic forces, and legal constraints” [28

Using Hospitals as Job Training and Employment Sites for the Developmentally Disabled. Hospital Industries Handbook.

ERIC Educational Resources Information Center

Balser, Richard M.; And Others

Based on the experiences of a job training demonstration project in five hospitals, the handbook describes a rationale and approach for using hospitals (rather than sheltered workshops) as job training sites for mentally and physically disabled persons. Part I reviews advantages for the hospital, the disabled person and his family, the…

Course Syllabus for Grades 9-12, Music. Chorus (I-IV).

ERIC Educational Resources Information Center

Murray State Univ., KY.

Teachers in the Henry County Public School System (Tennessee) developed and wrote over 80 course syllabi for most subject areas taught in grades seven through twelve as part of a Teacher Corps demonstration project. This syllabus is intended to inform students and parents of the requirements at each grade level of a four-year chorus program. The…

Technical Reports (Part II). End of Project Report, 1968-1971, Volume IV.

ERIC Educational Resources Information Center

Western Nevada Regional Education Center, Lovelock.

The pamphlets included in this volume are technical reports prepared as outgrowths of the Student Information System of the Western Nevada Regional Education Center funded by a Title III grant under the Elementary and Secondary Education Act of 1965. These reports demonstrate the use of the stored data; methods of interpreting the printouts from…

Low-delay predictive audio coding for the HIVITS HDTV codec

NASA Astrophysics Data System (ADS)

McParland, A. K.; Gilchrist, N. H. C.

1995-01-01

The status of work relating to predictive audio coding, as part of the European project on High Quality Video Telephone and HD(TV) Systems (HIVITS), is reported. The predictive coding algorithm is developed, along with six-channel audio coding and decoding hardware. Demonstrations of the audio codec operating in conjunction with the video codec, are given.

Navajo Materials For Classroom Use: K-12 Curriculum Directory (Preliminary Edition).

ERIC Educational Resources Information Center

Johnson, Gene, Comp.; And Others

Compiled as part of Title IV-B Materials Development Project at Rough Rock Demonstration School, the bibliography attempts to address: (1) what Navajo-based materials already exist and are available; (2) where Navajo curriculum development is currently taking place; and (3) what needs exist at the present stage of Navajo curriculum development.…

Science Education in Preschool: How to Assimilate the Reggio Emilia Pedagogy in a Turkish Preschool

ERIC Educational Resources Information Center

Inan, Hatice Zeynep

2009-01-01

This commentary manuscript, which was part of a larger research project, aimed to show how teachers can help preschoolers construct their knowledge of science and meet preschool science standards successfully in a Reggio Emilia approach. The demonstrations for preschool teachers are summarized as follows: be inspired by the Reggio Emilia approach;…

NASA Environmentally Responsible Aviation's Highly-Loaded Front Block Compressor Demonstration

NASA Technical Reports Server (NTRS)

Celestina, Mark

2017-01-01

The ERA project was created in 2009 as part of NASAs Aeronautics Research Mission Directorates (ARMD) Integrated Systems Aviation Program (IASP). The purpose of the ERA project was to explore and document the feasibility, benefit, and technical risk of vehicles concepts and enabling technologies to reduce aviations impact on the environment. The metrics for this technology is given in Figure 1 with the N+2 metrics highlighted in green. It is anticipated that the United States air transportation system will continue to expand significantly over the next few decades thus adversely impacting the environment unless new technology is incorporated to simultaneously reduce nitrous oxides (NOx), noise and fuel consumption. In order to achieve the overall goals and meet the technology insertion challenges, these goals were divided into technical challenges that were to be achieved during the execution of the ERA project. Technical challenges were accomplished through test campaigns conducted by Integrated Technology Demonstration (ITDs). ERAs technical performance period ended in 2015.

Energy survey study and report of hospitals in Chicago: South Suburban Hospital: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-08-01

This study is part of a three-phased demonstration project to reduce energy consumption in hospitals through practical life-cycle/cost-effective modifications and alteration. Funds for the demonstration project are provided by the American Hospital Association (AHA), the Department of Energy (DOE), and the Department of Health and Human Services (DHHS). A thorough study and evaluation of all building systems is made to identify opportunities for reduction in energy consumption and to determine the most cost effective approaches to energy conservation. The primary objective of the study is to investigate and analyze energy usage of the facility and to identify all life cycle,more » cost-effective changes required to effect a reduction in energy consumption. For the purpose of economic evaluation of the energy conservation projects identified, life-cycle cost and simple payback periods are used. Energy conservation measures with simple payback periods exceeding five years were dismissed from further detailed study.« less

A Pilot Project Demonstrating that Combat Medics Can Safely Administer Parenteral Medications in the Emergency Department.

PubMed

Schauer, Steven G; Cunningham, Cord W; Fisher, Andrew D; DeLorenzo, Robert A

2017-12-01

Introduction Select units in the military have improved combat medic training by integrating their functions into routine clinical care activities with measurable improvements in battlefield care. This level of integration is currently limited to special operations units. It is unknown if regular Army units and combat medics can emulate these successes. The goal of this project was to determine whether US Army combat medics can be integrated into routine emergency department (ED) clinical care, specifically medication administration. Project Design This was a quality assurance project that monitored training of combat medics to administer parenteral medications and to ensure patient safety. Combat medics were provided training that included direct supervision during medication administration. Once proficiency was demonstrated, combat medics would prepare the medications under direct supervision, followed by indirect supervision during administration. As part of the quality assurance and safety processes, combat medics were required to document all medication administrations, supervising provider, and unexpected adverse events. Additional quality assurance follow-up occurred via complete chart review by the project lead. Data During the project period, the combat medics administered the following medications: ketamine (n=13), morphine (n=8), ketorolac (n=7), fentanyl (n=5), ondansetron (n=4), and other (n=6). No adverse events or patient safety events were reported by the combat medics or discovered during the quality assurance process. In this limited case series, combat medics safely administered parenteral medications under indirect provider supervision. Future research is needed to further develop this training model for both the military and civilian setting. Schauer SG , Cunningham C W, Fisher AD , DeLorenzo RA . A pilot project demonstrating that combat medics can safely administer parenteral medications in the emergency department. Prehosp Disaster Med. 2017;32(6):679-681.

Combat Ration Advanced Manufacturing Technology Demonstration (CRAMTD). ’Generic Inspection-Statistical Process Control System for a Combat Ration Manufacturing Facility’. Short Term Project (STP) Number 3.

DTIC Science & Technology

1996-01-01

failure as due to an adhesive layer between the foil and inner polypropylene layers. "* Under subcontract, NFPA provided HACCP draft manuals for the...parameters of the production process and to ensure that they are within their target values. In addition, a HACCP program was used to assure product...played an important part in implementing Hazard Analysis Critical Control Points ( HACCP ) as part of the Process and Quality Control manual. The National

The American Board of Radiology Perspective on Maintenance of Certification: Part IV: Practice quality improvement in radiologic physics.

PubMed

Frey, G Donald; Ibbott, Geoffrey S; Morin, Richard L; Paliwal, Bhudatt R; Thomas, Stephen R; Bosma, Jennifer

2007-11-01

Recent initiatives of the American Board of Medical Specialties (ABMS) in the area of maintenance of certification (MOC) have been reflective of the response of the medical community to address public concerns regarding quality of care, medical error reduction, and patient safety. In March 2000, the 24 member boards of the ABMS representing all medical subspecialties in the USA agreed to initiate specialty-specific maintenance of certification (MOC) programs. The American Board of Radiology (ABR) MOC program for diagnostic radiology, radiation oncology, and radiologic physics has been developed, approved by the ABMS, and initiated with full implementation for all three disciplines beginning in 2007. The overriding objective of MOC is to improve the quality of health care through diplomate-initiated learning and quality improvement. The four component parts to the MOC process are: Part I: Professional standing, Part II: Evidence of life long learning and periodic self-assessment, Part III: Cognitive expertise, and Part IV: Evaluation of performance in practice (with the latter being the focus of this paper). The key components of Part IV require a physicist-based response to demonstrate commitment to practice quality improvement (PQI) and progress in continuing individual competence in practice. Diplomates of radiologic physics must select a project to be completed over the ten-year cycle that potentially can improve the quality of the diplomate's individual or systems practice and enhance the quality of care. Five categories have been created from which an individual radiologic physics diplomate can select one required PQI project: (1) Safety for patients, employees, and the public, (2) accuracy of analyses and calculations, (3) report turnaround time and communication issues, (4) practice guidelines and technical standards, and (5) surveys (including peer review of self-assessment reports). Each diplomate may select a project appropriate for an individual, participate in a project within a clinical department, participate in a peer review of a self-assessment report, or choose a qualified national project sponsored by a society. Once a project has been selected, the steps are: (1) Collect baseline data relevant to the chosen project, (2) review and analyze the data, (3) create and implement an improvement plan, (4) remeasure and track, and (5) report participation to the ABR, using the template provided by the ABR. These steps begin in Year 2, following training in Year 1. Specific examples of individual PQI projects for each of the three disciplines of radiologic physics are provided. Now, through the MOC programs, the relationship between the radiologic physicist and the ABR will be continuous through the diplomate's professional career. The ABR is committed to providing an effective infrastructure that will promote and assist the process of continuing professional development including the enhancement of practice quality improvement for radiologic physicists.

AGILIS: Agile Guided Interferometer for Longbaseline Imaging Synthesis. Demonstration and concepts of reconfigurable optical imaging interferometers

NASA Astrophysics Data System (ADS)

Woillez, Julien; Lai, Olivier; Perrin, Guy; Reynaud, François; Baril, Marc; Dong, Yue; Fédou, Pierre

2017-06-01

Context. In comparison to the radio and sub-millimetric domains, imaging with optical interferometry is still in its infancy. Due to the limited number of telescopes in existing arrays, image generation is a demanding process that relies on time-consuming reconfiguration of the interferometer array and super-synthesis. Aims: Using single mode optical fibres for the coherent transport of light from the collecting telescopes to the focal plane, a new generation of interferometers optimized for imaging can be designed. Methods: To support this claim, we report on the successful completion of the `OHANA Iki project: an end-to-end, on-sky demonstration of a two-telescope interferometer, built around near-infrared single mode fibres, carried out as part of the `OHANA project. Results: Having demonstrated that coherent transport by single-mode fibres is feasible, we explore the concepts, performances, and limitations of a new imaging facility with single mode fibres at its heart: Agile Guided Interferometer for Longbaseline Imaging Synthesis (AGILIS). Conclusions: AGILIS has the potential of becoming a next generation facility or a precursor to a much larger project like the Planet Formation Imager (PFI).

The national mobile health worker project in England.

PubMed

Drayton, Kathryn; Robinson, Karen

2014-01-01

Community services provide essential care to many, often vulnerable, people, families and communities along the spectrum from health promotion to end of life care. The Mobile Health Worker Project is part of a larger project, the Transforming Community Services programme, which was established to support providers make changes to service provision that would provide better health outcomes, as well as increasing efficiency through the use of technology. This paper draws on the results of the two phase Mobile Health Worker project which involved 11 sites around England, the aim of which was to understand the requirements of mobile working. The results demonstrate that increased productivity and efficiency can be achieved by making changes to working processes. The project also provides guidance to increase the rate of mobile working adoption by providing a solid economic basis for investment in and deployment of mobile solutions to community organisations.

US Astronomers Access to SIMBAD in Strasbourg, France

NASA Technical Reports Server (NTRS)

Eichhorn, G.; Oliverson, Ronald J. (Technical Monitor)

2003-01-01

During the last year the US SIMBAD Gateway Project continued to provide services like user registration to the US users of the SIMBAD database in France. Currently there are over 4300 US users registered. We also provided user support by answering questions from users and handling requests for lost passwords when still necessary. Even though almost all users now access SIMBAD without a password, based on hostnames/IP addresses, there are still some users that need individual passwords. We continued to maintain the mirror copy of the SIMBAD database on a server at SAO. This allows much faster access for the US users. During the past year we moved this mirror to a faster server to improve access for the US users. We again supported a demonstration of the SIMBAD database at the meeting of the American Astronomical Society in January. We provided support for the demonstration activities at the SIMBAD booth. We paid part of the fee for the SIMBAD demonstration. We continued to improve the cross-linking between the SIMBAD project and the Astrophysics Data System. This cross-linking between these systems is very much appreciated by the users of both the SIMBAD database and the ADS Abstract Service. The mirror of the SIMBAD database at SAO makes this connection faster for the US astronomers. We exchange information between the ADS and SIMBAD on a daily basis. The close cooperation between the CDS in Strasbourg and SAO, facilitated by this project, is an important part of the astronomy-wide digital library initiative. It has proven to be a model in how different data centers can collaborate and enhance the value of their products by linking with other data centers. We continue this collaboration in order to provide better services to both the US and European astronomical community. This collaboration is even more important in light of the developments for the Virtual Observatory projects in the different countries.

Afferent projections to the mammillary complex of the rat, with special reference to those from surrounding hypothalamic regions

NASA Technical Reports Server (NTRS)

Gonzalo-Ruiz, A.; Alonso, A.; Sanz, J. M.; Llinas, R. R.

1992-01-01

To better understand the functional organization of the mammillary nuclei, we investigated the afferents to this nuclear complex in the rat with iontophoretically injected wheat germ agglutinin conjugated to horseradish peroxidase. Particular attention was paid to tracing local hypothalamic afferents to these nuclei. Injections into the medial mammillary nucleus (MMN) revealed strong projections from the subicular region, and weaker projections from the prefrontal cortex, medial septum, and the nucleus of the diagonal band of Broca. Other descending subcortical projections to the MMN arise from the anterior and the lateral hypothalamic area, the medial preoptic area, and the bed nucleus of the stria terminalis. Ascending afferents to the MMN were found to originate in the raphe and various tegmental nuclei. Following all injections into the MMN, labelled neurons were found in nuclei surrounding the mammillary body. The lateral and posterior subdivisions of the tuberomammillary nucleus projected mainly to the pars medianus and pars medialis of the MMN. The dorsal and ventral premammillary nuclei projected to the pars lateralis of the MMN. The supramammillary nucleus at rostral level had a small projection to the pars medialis and lateralis of the MMN. However, the most obvious projection from this nucleus was to the pars posterior of the MMN, chiefly from the lateral part of the caudal supramammillary nucleus. Injections into the lateral mammillary nucleus revealed inputs from the presubiculum, parasubiculum, septal region, dorsal tegmental nucleus, dorsal raphe nucleus, and periaqueductal gray. In addition, the lateral mammillary nucleus was found to receive a moderate projection from the medial part of the supramammillary nucleus and stronger projections from the lateral part of the caudal supramammillary nucleus. A very light projection was also seen from the lateral and posterior subdivisions of the tuberomammillary nucleus. These findings add to our knowledge of the extensive and complex connectivity of the mammillary nuclei. In particular, the local connections we have demonstrated with the supramammillary and tuberomammillary nuclei indicate the existence of significant local circuits as well as circuits involving more distant brain regions such as the septal nuclei, subiculum, prefrontal cortex, and brain stem tegmentum.

Enery Efficient Press and Sinter of Titanium Powder for Low-Cost Components in Vehicle Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas Zwitter; Phillip Nash; Xiaoyan Xu

2011-03-31

This is the final technical report for the Department of Energy NETL project NT01931 Energy Efficient Press and Sinter of Titanium Powder for Low-Cost Components in Vehicle Applications. Titanium has been identified as one of the key materials with the required strength that can reduce the weight of automotive components and thereby reduce fuel consumption. Working with newly developed sources of titanium powder, Webster-Hoff will develop the processing technology to manufacture low cost vehicle components using the single press/single sinter techniques developed for iron based powder metallurgy today. Working with an automotive or truck manufacturer, Webster-Hoff will demonstrate the feasibilitymore » of manufacturing a press and sinter titanium component for a vehicle application. The project objective is two-fold, to develop the technology for manufacturing press and sinter titanium components, and to demonstrate the feasibility of producing a titanium component for a vehicle application. The lowest cost method for converting metal powder into a net shape part is the Powder Metallurgy Press and Sinter Process. The method involves compaction of the metal powder in a tool (usually a die and punches, upper and lower) at a high pressure (up to 60 TSI or 827 MPa) to form a green compact with the net shape of the final component. The powder in the green compact is held together by the compression bonds between the powder particles. The sinter process then converts the green compact to a metallurgically bonded net shape part through the process of solid state diffusion. The goal of this project is to expand the understanding and application of press and sinter technology to Titanium Powder applications, developing techniques to manufacture net shape Titanium components via the press and sinter process. In addition, working with a vehicle manufacturer, demonstrate the feasibility of producing a titanium component for a vehicle. This is not a research program, but rather a project to develop a process for press and sinter of net shape Titanium components. All of these project objectives have been successfully completed.« less

Facility Activation and Characterization for IPD Workhorse Preburner and Oxidizer Turbopump Hot-Fire Testing at NASA Stennis Space Center

NASA Technical Reports Server (NTRS)

Sass, J. P.; Raines, N. G.; Ryan, H. M.

2004-01-01

The Integrated Powerhead Demonstrator (IPD) is a 250K lbf (1.1 MN) thrust cryogenic hydrogen/oxygen engine technology demonstrator that utilizes a full flow staged combustion engine cycle. The Integrated Powerhead Demonstrator (IPD) is part of NASA's Next Generation Launch Technology (NGLT) program, which seeks to provide safe, dependable, cost-cutting technologies for future space launch systems. The project also is part of the Department of Defense's Integrated High Payoff Rocket Propulsion Technology (IHPRPT) program, which seeks to increase the performance and capability of today s state-of-the-art rocket propulsion systems while decreasing costs associated with military and commercial access to space. The primary industry participants include Boeing-Rocketdyne and GenCorp Aerojet. The intended full flow engine cycle is a key component in achieving all of the aforementioned goals. The IPD Program recently achieved a major milestone with the successful completion of the IPD Oxidizer Turbopump (OTP) hot-fire test project at the NASA John C. Stennis Space Center (SSC) E-1 test facility in June 2003. A total of nine IPD Workhorse Preburner tests were completed, and subsequently 12 IPD OTP hot-fire tests were completed. The next phase of development involves IPD integrated engine system testing also at the NASA SSC E-1 test facility scheduled to begin in late 2004. Following an overview of the NASA SSC E-1 test facility, this paper addresses the facility aspects pertaining to the activation and testing of the IPD Workhorse Preburner and the IPD Oxidizer Turbopump. In addition, some of the facility challenges encountered during the test project shall be addressed.

Experience with modified aerospace reliability and quality assurance method for wind turbines

NASA Technical Reports Server (NTRS)

Klein, W. E.

1982-01-01

The SR&QA approach assures that the machine is not hazardous to the public or operating personnel, can operate unattended on a utility grid, demonstrates reliability operation, and helps establish the quality assurance and maintainability requirements for future wind turbine projects. The approach consisted of modified failure modes and effects analysis (FMEA) during the design phase, minimal hardware inspection during parts fabrication, and three simple documents to control activities during machine construction and operation. Five years experience shows that this low cost approach works well enough that it should be considered by others for similar projects.

Remote Sensing, Air Quality, and Public Health

NASA Technical Reports Server (NTRS)

Quattrochi, Dale A.; Rickman, Douglas; Mohammad, Al-Hamdan; Crosson, William; Estes, Maurice, Jr.; Limaye, Ashutosh; Qualters, Judith

2008-01-01

HELIX-Atlanta was developed to support current and future state and local EPHT programs to implement data linking demonstratio'n projects which could be part of the EPHT Network. HELIX-Atlanta is a pilot linking project in Atlanta for CDC to learn about the challenges the states will encounter. NASA/MSFC and the CDC are partners in linking environmental and health data to enhance public health surveillance. The use of NASA technology creates value - added geospatial products from existing environmental data sources to facilitate public health linkages. Proving the feasibility of the approach is the main objective

Neuroimaging Data Sharing on the Neuroinformatics Database Platform

PubMed Central

Book, Gregory A; Stevens, Michael; Assaf, Michal; Glahn, David; Pearlson, Godfrey D

2015-01-01

We describe the Neuroinformatics Database (NiDB), an open-source database platform for archiving, analysis, and sharing of neuroimaging data. Data from the multi-site projects Autism Brain Imaging Data Exchange (ABIDE), Bipolar-Schizophrenia Network on Intermediate Phenotypes parts one and two (B-SNIP1, B-SNIP2), and Monetary Incentive Delay task (MID) are available for download from the public instance of NiDB, with more projects sharing data as it becomes available. As demonstrated by making several large datasets available, NiDB is an extensible platform appropriately suited to archive and distribute shared neuroimaging data. PMID:25888923

Pacific Northwest GridWise™ Testbed Demonstration Projects; Part I. Olympic Peninsula Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammerstrom, Donald J.; Ambrosio, Ron; Carlon, Teresa A.

2008-01-09

This report describes the implementation and results of a field demonstration wherein residential electric water heaters and thermostats, commercial building space conditioning, municipal water pump loads, and several distributed generators were coordinated to manage constrained feeder electrical distribution through the two-way communication of load status and electric price signals. The field demonstration took place in Washington and Oregon and was paid for by the U.S. Department of Energy and several northwest utilities. Price is found to be an effective control signal for managing transmission or distribution congestion. Real-time signals at 5-minute intervals are shown to shift controlled load in time.more » The behaviors of customers and their responses under fixed, time-of-use, and real-time price contracts are compared. Peak loads are effectively reduced on the experimental feeder. A novel application of portfolio theory is applied to the selection of an optimal mix of customer contract types.« less

Conversion of Coal Mine Gas to LNG

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This project evolved from a 1995, DOE-NETL competitive solicitation for practical CMM capture and utilization concepts. Appalachian Pacific was one of three companies selected to proceed with the construction and operation of a cost-shared demonstration plant. In the course of trying to proceed with this demonstration plant, AP examined several liquefaction technologies, discussed obtaining rights to coal mine methane with a number of coal companies, explored marketing potential with a wide variety of customers in many sections of the United States, studied in great detail the impact of a carbon credit exchange, and developed a suite of analytical tools withmore » which to evaluate possible project options. In the end, the newness of the product, reluctance on the part of the coal companies to venture away from time tested practices, difficulty with obtaining financing, the failure of a carbon credit market to develop and the emergence of shale derived gas production prevented a demonstration plant from being built.« less

Compute-to-Learn: Authentic Learning via Development of Interactive Computer Demonstrations within a Peer-Led Studio Environment

ERIC Educational Resources Information Center

Jafari, Mina; Welden, Alicia Rae; Williams, Kyle L.; Winograd, Blair; Mulvihill, Ellen; Hendrickson, Heidi P.; Lenard, Michael; Gottfried, Amy; Geva, Eitan

2017-01-01

In this paper, we report on the implementation of a novel compute-to-learn pedagogy, which is based upon the theories of situated cognition and meaningful learning. The "compute-to-learn" pedagogy is designed to simulate an authentic research experience as part of the undergraduate curriculum, including project development, teamwork,…

"Boomsville to Doomsville" - Development of Industry Within a Community. Environmental Ecological Education Project. Revised, July 1973.

ERIC Educational Resources Information Center

Abbott, Verlin M.

This unit, developed for use with junior high school students, focuses on industry as an integral part of community life. It discusses factors industry should consider before choosing a location; it attempts to demonstrate that industry should not always be regarded negatively in a given community, but rather that it can benefit a community by…

Using Dynamic Geometry Software To Add Contrast to Geometric Situations--A Case Study.

ERIC Educational Resources Information Center

Holzl, Reinhard

2001-01-01

Uses of Dynamic Geometry Software (DGS) are often limited purely to a verifying role. Presents a case study that emerged from a project in which DGS formed an integral part of the pedagogical arrangement. The study demonstrates how the contrasting power of DGS might be utilized in a guided discovery setting. (Contains 17 references.) (Author/ASK)

TECHNOLOGY AND MANPOWER IN DESIGN AND DRAFTING 1965-75. MANPOWER RESEARCH BULLETIN NUMBER 12.

ERIC Educational Resources Information Center

Office of Manpower Policy, Evaluation, and Research (DOL), Washington, DC.

AS PART OF AN EXPERIMENTAL AND DEMONSTRATION PROJECT LAUNCHED BY THE DEPARTMENT OF LABOR IN 1965 TO EMPHASIZE LIKELY FUTURE TECHNOLOGICAL AND MANPOWER CHANGES, THIS STUDY OF THE DESIGN AND DRAFTING PROCESS AIMED TO IDENTIFY THE MAJOR TECHNOLOGICAL CHANGES IN THE NEXT 10 YEARS, TO DETERMINE THE EXTENT AND RATE OF DIFFUSION OF THESE CHANGES, AND TO…

Making a Connection in the International Baccalaureate English Classroom: Using Multimodal Projects to Better Understand Students

ERIC Educational Resources Information Center

Cicione, Phillip M.

2012-01-01

The main focus of this dissertation is the literacy practices of students in a high school International Baccalaureate (IB) English classroom. The students demonstrated their meaning of texts that were studied as part of the curriculum in order to prepare them for their Formal Oral Commentaries. This was a mandated assessment of the IB English…

Course Syllabus for Grades 10-12, Art. Art 2 + 3.

ERIC Educational Resources Information Center

Murray State Univ., KY.

This course syllabus is one of over 80 developed and written by the Henry County School System (Tennessee) as part of a Teacher Corps demonstration project. These syllabi provide specific descriptions of what is to be learned and at what level the student is expected to perform. The art course described here is available for students who have…

The Link between the Process of Change and Coaching in an Organization--A Case Study

ERIC Educational Resources Information Center

Jim, Josephine

2016-01-01

The aim of this case study was to highlight coaching in the process of change using a real life information technology and operational change project in an institution. It demonstrates the critical importance of coaching in change management, for successful change to occur. Any sustaining change requires ongoing coaching as an integral part of the…

Virginia Demonstration Project Encouraging Middle School Students in Pursuing STEM Careers

NASA Technical Reports Server (NTRS)

Bachman, Jane T.; Kota, Dena H.; Kota, Aaron J.

2011-01-01

Encouraging students at all grade levels to consider pursuing a career in Science, Technology, Engineering, and Mathematics (STEM) fields i s a national focus. In 2005, the Naval Surface Warfare Center, Dahlgren Division (NSWCDD), a Department of Defense laboratory located in Da hlgren, Virginia, began work on the Virginia Demonstration Project (VDP) with the goal of increasing more student interest in STEM educatio n and pursuing STEM careers. This goal continues as the program enters its sixth year. This project has been successful through the partici pation of NSWCDD's scientists and engineers who are trained as mentor s to work in local middle school classrooms throughout the school year, As an extension of the in-class activities, several STEM summer aca demies have been conducted at NSWCDD, These academies are supported by the Navy through the VDP and the STEM Learning Module Project. These projects are part of more extensive outreach efforts offered by the National Defense Education Program (NDEP), sponsored by the Director, Defense Research and Engineering. The focus of this paper is on the types of activities conducted at the summer academy, an overview of the academy planning process, and recommendations to help support a nati onal plan of integrating modeling and simulation-based engineering and science into all grade levels. based upon the lessons learned

The helping relationship in the community setting: the relevance of Rogerian theory to the supervision of Project 2000 students.

PubMed

Hallett, C E

1997-12-01

A series of twenty-six interviews, fourteen with district nursing sisters and twelve with students they supervised, was conducted in 1992 in one Project 2000 demonstration district in England. The data were collected as part of an English National Board funded research study; data were reinterpreted in 1994 and formed one element in the author's PhD thesis. Participants described the ways in which a supervisor might enable a student to learn during a community placement. One of the most important means by which supervisors could provide assistance was by creating an environment in which the students felt supported. Students described how supervisors demonstrated concern, acceptance and understanding, attributes which bore striking resemblance to the qualities of congruence, unconditional positive regard and empathic understanding identified by Carl Rogers as enabling learning.

Groundwater cleanup demonstrations at Complex 34, CCAS

NASA Technical Reports Server (NTRS)

2000-01-01

At Launch Complex 34, the Six-Phase Soil Heating site that is involved in a groundwater cleanup project can be seen. The project involves the Department of Defense, Environmental Protection Agency, Department of Energy and NASA. Concentrations of trichloroethylene solvent have been identified in the soil at the complex as a result of cleaning methods for rocket parts during the Apollo Program, which used the complex, in the 60s. The group formed the Interagency NDAPL Consortium (IDC) to study three contamination cleanup technologies: Six-Phase Soil Heating, Steam Injection and In Situ Oxidation with Potassium Permanganate. All three methods may offer a way to remove the contaminants in months instead of decades. In the background is the block house for the complex. KSC hosted a two-day conference that presented information and demonstrations of the three technologies being tested at the site.

Flight Services and Aircraft Access: Active Flow Control Vertical Tail and Insect Accretion and Mitigation Flight Test

NASA Technical Reports Server (NTRS)

Whalen, Edward A.

2016-01-01

This document serves as the final report for the Flight Services and Aircraft Access task order NNL14AA57T as part of NASA Environmentally Responsible Aviation (ERA) Project ITD12A+. It includes descriptions of flight test preparations and execution for the Active Flow Control (AFC) Vertical Tail and Insect Accretion and Mitigation (IAM) experiments conducted on the 757 ecoDemonstrator. For the AFC Vertical Tail, this is the culmination of efforts under two task orders. The task order was managed by Boeing Research & Technology and executed by an enterprise-wide Boeing team that included Boeing Research & Technology, Boeing Commercial Airplanes, Boeing Defense and Space and Boeing Test and Evaluation. Boeing BR&T in St. Louis was responsible for overall Boeing project management and coordination with NASA. The 757 flight test asset was provided and managed by the BCA ecoDemonstrator Program, in partnership with Stifel Aircraft Leasing and the TUI Group. With this report, all of the required deliverables related to management of this task order have been met and delivered to NASA as summarized in Table 1. In addition, this task order is part of a broader collaboration between NASA and Boeing.

Investigation on Smart Parts with Embedded Piezoelectric Sensors via Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Yirong

The goal of this proposed research is to design, fabricate, and evaluate “smart parts” with embedded sensors for energy systems. The “smart parts” will be fabricated using Electron Beam Melting (EBM) 3D printing technique with built-in piezoceramic sensors. The objectives of the proposed project are: 1) Fabricate energy system related components with embedded sensors, 2) Evaluate the mechanical properties and sensing functionalities of the “smart parts” with embedded piezoceramic sensors, and 3) Assess in-situ sensing capability of energy system parts. The second year’s research of the research is centered on fabrication of the “smart parts” with considerations of overall materialmore » property as well as demonstration of sensing functionalities. The results for the final report are presented here, including all research accomplishment, project management. Details are included such as: how the design and fabrication of sensor packaging could improve the sensor performance, demonstration of “smart parts” sensing capabilities, analysis on the elements that constitute the “smart sensors”, advanced “stop and go” fabrication process, smart injector fabrication using SLM technology, smart injector testing in combustion environments etc. Research results to date have generated several posters and papers.« less

Field evaluation of a horizontal well recirculation system for groundwater treatment: Field demonstration at X-701B Portsmouth Gaseous Diffusion Plant, Piketon, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korte, N.; Muck, M.; Kearl, P.

1998-08-01

This report describes the field-scale demonstration performed as part of the project, In Situ Treatment of Mixed Contaminants in Groundwater. This project was a 3{1/2} year effort comprised of laboratory work performed at Oak Ridge National Laboratory and fieldwork performed at the US Department of Energy (DOE) Portsmouth Gaseous Diffusion Plant (PORTS). The overall goal of the project was to evaluate in situ treatment of groundwater using horizontal recirculation coupled with treatment modules. Specifically, horizontal recirculation was tested because of its application to thin, interbedded aquifer zones. Mixed contaminants were targeted because of their prominence at DOE sites and becausemore » they cannot be treated with conventional methods. The project involved several research elements, including treatment process evaluation, hydrodynamic flow and transport modeling, pilot testing at an uncontaminated site, and full-scale testing at a contaminated site. This report presents the results of the work at the contaminated site, X-701B at PORTS. Groundwater contamination at X-701B consists of trichloroethene (TCE) (concentrations up to 1800 mg/L) and technetium-998 (Tc{sup 99}) (activities up to 926 pCi/L).« less

System Characterizations and Optimized Reconstruction Methods for Novel X-ray Imaging Modalities

NASA Astrophysics Data System (ADS)

Guan, Huifeng

In the past decade there have been many new emerging X-ray based imaging technologies developed for different diagnostic purposes or imaging tasks. However, there exist one or more specific problems that prevent them from being effectively or efficiently employed. In this dissertation, four different novel X-ray based imaging technologies are discussed, including propagation-based phase-contrast (PB-XPC) tomosynthesis, differential X-ray phase-contrast tomography (D-XPCT), projection-based dual-energy computed radiography (DECR), and tetrahedron beam computed tomography (TBCT). System characteristics are analyzed or optimized reconstruction methods are proposed for these imaging modalities. In the first part, we investigated the unique properties of propagation-based phase-contrast imaging technique when combined with the X-ray tomosynthesis. Fourier slice theorem implies that the high frequency components collected in the tomosynthesis data can be more reliably reconstructed. It is observed that the fringes or boundary enhancement introduced by the phase-contrast effects can serve as an accurate indicator of the true depth position in the tomosynthesis in-plane image. In the second part, we derived a sub-space framework to reconstruct images from few-view D-XPCT data set. By introducing a proper mask, the high frequency contents of the image can be theoretically preserved in a certain region of interest. A two-step reconstruction strategy is developed to mitigate the risk of subtle structures being oversmoothed when the commonly used total-variation regularization is employed in the conventional iterative framework. In the thirt part, we proposed a practical method to improve the quantitative accuracy of the projection-based dual-energy material decomposition. It is demonstrated that applying a total-projection-length constraint along with the dual-energy measurements can achieve a stabilized numerical solution of the decomposition problem, thus overcoming the disadvantages of the conventional approach that was extremely sensitive to noise corruption. In the final part, we described the modified filtered backprojection and iterative image reconstruction algorithms specifically developed for TBCT. Special parallelization strategies are designed to facilitate the use of GPU computing, showing demonstrated capability of producing high quality reconstructed volumetric images with a super fast computational speed. For all the investigations mentioned above, both simulation and experimental studies have been conducted to demonstrate the feasibility and effectiveness of the proposed methodologies.

On the transverse-traceless projection in lattice simulations of gravitational wave production

NASA Astrophysics Data System (ADS)

Figueroa, Daniel G.; García-Bellido, Juan; Rajantie, Arttu

2011-11-01

It has recently been pointed out that the usual procedure employed in order to obtain the transverse-traceless (TT) part of metric perturbations in lattice simulations was inconsistent with the fact that those fields live in the lattice and not in the continuum. It was claimed that this could lead to a larger amplitude and a wrong shape for the gravitational wave (GW) spectra obtained in numerical simulations of (p)reheating. In order to address this issue, we have defined a consistent prescription in the lattice for extracting the TT part of the metric perturbations. We demonstrate explicitly that the GW spectra obtained with the old continuum-based TT projection only differ marginally in amplitude and shape with respect to the new lattice-based ones. We conclude that one can therefore trust the predictions appearing in the literature on the spectra of GW produced during (p)reheating and similar scenarios simulated on a lattice.

Habitat Demonstration Unit Project Leadership and Management Strategies

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.

2011-01-01

This paper gives an overview of the National Aeronautics and Space Administration (NASA) led multi-center Habitat Demonstration Unit (HDU) project leadership and management strategies. The HDU project team constructed and tested an analog prototype lunar surface habitat/laboratory called the Pressurized Excursion Module (PEM) during 2010. The prototype unit subsystems were integrated in a short amount of time, utilizing a tiger team approach that brought together over 20 habitation-related technologies and innovations from a variety of NASA centers. This paper describes the leadership and management strategies as well as lessons learned pertaining to leading and managing a multi-center diverse team in a rapid prototype environment. The PEM configuration went from a paper design to an operational surface habitat demonstration unit in less than 12 months. The HDU project is part of the strategic plan from the Exploration Systems Mission Directorate (ESMD) Directorate Integration Office (DIO) and the Exploration Mission Systems Office (EMSO) to test destination elements in analog environments. The 2011 HDU-Deep Space Habitat (DSH) configuration will build upon the PEM work, and emphasize validity of crew operations (remote working and living), EVA operations, mission operations, logistics operations, and science operations that might be required in a deep space context for Near Earth Object (NEO) exploration mission architectures. The 2011 HDU-DSH will be field-tested during the 2011 Desert Research and Technologies Studies (DRaTS) field tests. The HDU project is a "technology-pull" project that integrates technologies and innovations from multiple NASA centers. This project will repurpose the HDU 2010 demo unit that was field tested in the 2010 DRaTS, adding habitation functionality to the prototype unit. This paper will describe the strategy of establishing a multi-center project management team that put in place the key multi-center leadership skills and disciplines to enable a successful tiger team approach. Advocacy was established with key stakeholders and NASA Headquarters (HQ) by defining a strategic vision, mission, goals and objectives for the project and team. As a technology-pull testbed capability the HDU project was able to collaborate and leverage the Exploration Technology Development Program (ETDP) and individual NASA center investments which capitalized on their respective center core competencies and skills. This approach enable the leveraging of over $7.5m of value to create an operational habitat demonstration unit 2010 PEM configuration.

Puget Sound Tidal Energy In-Water Testing and Development Project Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collar, Craig W

2012-11-16

Tidal energy represents potential for the generation of renewable, emission free, environmentally benign, and cost effective energy from tidal flows. A successful tidal energy demonstration project in Puget Sound, Washington may enable significant commercial development resulting in important benefits for the northwest region and the nation. This project promoted the United States Department of Energy's Wind and Hydropower Technologies Program's goals of advancing the commercial viability, cost-competitiveness, and market acceptance of marine hydrokinetic systems. The objective of the Puget Sound Tidal Energy Demonstration Project is to conduct in-water testing and evaluation of tidal energy technology as a first step towardmore » potential construction of a commercial-scale tidal energy power plant. The specific goal of the project phase covered by this award was to conduct all activities necessary to complete engineering design and obtain construction approvals for a pilot demonstration plant in the Admiralty Inlet region of the Puget Sound. Public Utility District No. 1 of Snohomish County (The District) accomplished the objectives of this award through four tasks: Detailed Admiralty Inlet Site Studies, Plant Design and Construction Planning, Environmental and Regulatory Activities, and Management and Reporting. Pre-Installation studies completed under this award provided invaluable data used for site selection, environmental evaluation and permitting, plant design, and construction planning. However, these data gathering efforts are not only important to the Admiralty Inlet pilot project. Lessons learned, in particular environmental data gathering methods, can be applied to future tidal energy projects in the United States and other parts of the world. The District collaborated extensively with project stakeholders to complete the tasks for this award. This included Federal, State, and local government agencies, tribal governments, environmental groups, and others. All required permit and license applications were completed and submitted under this award, including a Final License Application for a pilot hydrokinetic license from the Federal Energy Regulatory Commission. The tasks described above have brought the project through all necessary requirements to construct a tidal pilot project in Admiralty Inlet with the exception of final permit and license approvals, and the selection of a general contractor to perform project construction.« less

Project support of practical training in biophysics.

PubMed

Mornstein, V; Vlk, D; Forytkova, L

2006-01-01

The Department of Biophysics ensures practical training in biophysics and related subjects for students of medical and health study programmes. Demonstrations of medical technology are an important part of this training. Teaching for Faculty of Sciences in biophysical study programmes becomes also very important. Some lectures and demonstrations of technology are involved, but the practical trainig is missing. About 1 mil. CZK for additional laboratory equipment was obtained from the HEIDF project No. 1866/ 2005 "The demonstration and measuring technology for education in medical biophysics and radiological physics" for measuring system DEWETRON for high frequency signal analysis, Fluke Ti30 IR camera, PM 9000B patient monitor, ARSENAL AF 1 fluorescence microscope, and Nikon Coolpix 4500 digital camera with accessories for microphotography. At the present time, further financial resources are being provided by a development project of Ministry of Education "Inter-university co-operation in biomedical technology and engineering using top technologies" in total amount of almost 5 mil CZK, whereas over 2 mil CZK from this project are reserved for student laboratory equipment. The main goal of this project is to ensure the participation of Medical Faculty in educational co-operation in the biomedical technology and engineering, namely with the Faculty of Electrical Engineering and Communication (FEEC), Brno University of Technology. There will be taught those areas of biophysics which are not covered by FEEC, thus forming a separate subject "General Biophysics". The following instruments will be installed: UV-VIS spectrophotometers, rotation viscometers, tensiometers, microscopes with digital image processing, cooled centrifuge, optical benches, and some smaller instruments for practical measurements.

RM12-2703 Advanced Rooftop Unit Control Retrofit Kit Field Demonstration: Hawaii and Guam Energy Improvement Technology Demonstration Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doebber, I.; Dean, J.; Dominick, J.

2014-03-01

As part of its overall strategy to meet its energy goals, the Naval Facilities Engineering Command (NAVFAC) partnered with U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to rapidly demonstrate and deploy cost-effective renewable energy and energy efficiency technologies. This was one of several demonstrations of new and underutilized commercial energy efficiency technologies. The consistent year-round demand for air conditioning and dehumidification in Hawaii provides an advantageous demonstration location for advanced rooftop control (ARC) retrofit kits to packaged rooftop units (RTUs). This report summarizes the field demonstration of ARCs installed on nine RTUs serving a 70,000-ft 2 exchangemore » store (large retail) and two RTUs, each serving small office buildings located on Joint Base Pearl Harbor-Hickam (JBPHH).« less

A 'private adventure'? John Herschel's Cape voyage and the production of the 'Cape Results'

NASA Astrophysics Data System (ADS)

Ruskin, Steven William

2002-07-01

This dissertation considers the life of John Herschel (1792 1871) from the years 1833 to 1847. In 1833 Herschel sailed from London to Cape Town, southern Africa, to undertake (at his own expense) an astronomical exploration of the southern heavens, as well as a terrestrial exploration of the area around Cape Town. After his return to England in 1838, he was highly esteemed and became Britain's most recognized scientist. In 1847 his southern hemisphere astronomical observations were published as the Cape Results. The main argument of this dissertation is that Herschel's voyage, and the publication of the Cape Results, in addition to their contemporary scientific importance, were also significant for nineteenth-century politics and culture. This dissertation is a two-part dissertation. The first part is entitled “John Herschel's Cape Voyage: Private Science, Public Imagination, and the Ambitions of Empire”; and the second part, “The Production of the Cape Results.” In the first part it is demonstrated that the reason for Herschel's cultural renown was the popular notion that his voyage to the Cape was a project aligned with the imperial ambitions of the British government. By leaving England for one of its colonies, and pursuing there a significant scientific project, Herschel was seen in the same light as other British men of science who had also undertaken voyages of exploration and discovery. It is then demonstrated, in the second part of this work, that the production of the Cape Results, in part because of Herschel's status as Britain's scientific figurehead, was a significant political and cultural event. In addition to the narrow area of Herschel scholarship, this dissertation touches on other areas of research in the history of science as well: science and culture, science and empire, science and politics, and what has been called the “new” history of scientific books.

Defense Health Care: DOD Chiropractor Wage Rates

DTIC Science & Technology

2013-03-14

Page 2 Introduction • In 2000, Congress mandated that the Department of Defense (DOD) develop a plan to provide chiropractic care as a permanent...part of the Defense Health Program. • Prior to the establishment of DOD’s chiropractic program, Congress directed DOD to conduct demonstration...projects to evaluate the feasibility and advisability of expanding DOD’s health system to include chiropractic care. • The National Defense

Using Stimulated Recall to Investigate Pupils' Thinking about Online Bilingual Communication: Code-Switching and Pronominal Address in L2 French

ERIC Educational Resources Information Center

Evans, Michael

2009-01-01

This article demonstrates how evidence related to performance in computer mediated communication (CMC) can be used as a vehicle for researching pupils' thinking about using and learning a foreign language. The analysis is based on a qualitative study of pupils from two contrasting schools who had taken part in a multinational CMC project involving…

A Practice/Research Collaborative: An Innovative Approach to Identifying and Responding to Psychosocial Functioning Problems and Recidivism Risk among Juvenile Arrestees

ERIC Educational Resources Information Center

Dembo, Richard; Walters, Wansley; Meyers, Kathleen

2005-01-01

Effectively identifying and responding to the psychosocial problems and recidivism risk of arrested youths remain critical needs in the field. Centralized intake facilities, such as juvenile assessment centers (JACs), can play a key role in this process. As part of a U.S. National Demonstration Project, the Miami-Dade JAC, serving a…

Identifying "redtops": Classification of satellite imagery for tracking mountain pine beetle progression through a pine forest

Treesearch

Richard Cutler; Leslie Brown; James Powell; Barbara Bentz; Adele Cutler

2003-01-01

Mountain pine beetles (Dendroctonus ponderosae Hopkins) are a pest indigenous to the pine forests of the western United States. Capable of exponential population growth, mountain pine beetles can destroy thousands of acres of trees in a short period of time. The research reported here is part of a larger project to demonstrate the application of, and evaluate,...

The Use of Drama to Teach Social Skills in a Special School Setting for Students with Autism

ERIC Educational Resources Information Center

Kempe, Andy; Tissot, Cathy

2012-01-01

For children with autism, social challenges may be both part of the disability and a barrier to accessing education. This article reports on a project that used drama to address such challenges by drawing on the social skills of non-autistic peers in a special school setting. The article demonstrates how drama's flexibility may be harnessed in…

More than the Sum of the Parts: Using Small Group Learning in Adult Basic and Literacy Education. A 353 Special Demonstration Project.

ERIC Educational Resources Information Center

Imel, Susan; And Others

This guide provides practical information that teachers and administrators can use to initiate the small group learning approach in adult basic and literacy education (ABLE). A locator index directs readers to specific topics. Chapter 1 describes small group learning, provides a rationale, and points out advantages and disadvantages for learners,…

Predictive Engineering Tools for Injection-Molded Long-Carbon-Thermoplastic Composites: Weight and Cost Analyses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Fifield, Leonard S.; Gandhi, Umesh N.

This project proposed to integrate, optimize and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk Simulation Moldflow Insight (ASMI) package for injection-molded long-carbon-fiber thermoplastic composites into a cohesive prediction capability. The current effort focused on rendering the developed models more robust and efficient for automotive industry part design to enable weight savings and cost reduction. The project goal has been achieved by optimizing the developed models, improving and integrating their implementations in ASMI, and validating them for a complex 3D LCF thermoplastic automotive part (Figure 1). Both PP and PA66 were used asmore » resin matrices. After validating ASMI predictions for fiber orientation and fiber length for this complex part against the corresponding measured data, in collaborations with Toyota and Magna PNNL developed a method using the predictive engineering tool to assess LCF/PA66 complex part design in terms of stiffness performance. Structural three-point bending analyses of the complex part and similar parts in steel were then performed for this purpose, and the team has then demonstrated the use of stiffness-based complex part design assessment to evaluate weight savings relative to the body system target (≥ 35%) set in Table 2 of DE-FOA-0000648 (AOI #1). In addition, starting from the part-to-part analysis, the PE tools enabled an estimated weight reduction for the vehicle body system using 50 wt% LCF/PA66 parts relative to the current steel system. Also, from this analysis an estimate of the manufacturing cost including the material cost for making the equivalent part in steel has been determined and compared to the costs for making the LCF/PA66 part to determine the cost per “saved” pound.« less

Methodology for producing 100 tons of fuel peat for a cement plant test burn. Metodologia para producir 100 toneladas de turba combustible para una prueba de quema en uns planta de cemento (in English; Spanish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, A.B.; Malavassi, L.; Ramirez, O.

1989-05-01

As a part of the Agency for International Development-funded cooperative project between Los Alamos and Costa Rica, the burning characteristics of Costa Rican peat were to be tested in an application. The cement plant owned by Industria National de Cemento in Cartago has a capability to handle solid fuel and was chosen for the burn demonstration. The Jungle No. 1 Peat Deposit near El Cairo was chosen as the site of the peat excavation. This peat production methodology study covers project site selection, installation of an access road and clearing of the jungle vegetation, removal of an upper layer ofmore » organic peat, excavation of fuel-grade peat, transport of the peat to the drying site, and drying and stockpiling of the finished product. As of this date the peat removal for the demonstration project has been started, and a description of the operation is included as an appendix to this paper. 10 figs.« less

Research use of the AIDA www.2aida.org diabetes software simulation program: a review--part 2. Generating simulated blood glucose data for prototype validation.

PubMed

Lehmann, Eldon D

2003-01-01

The purpose of this review is to describe research applications of the AIDA diabetes software simulator. AIDA is a computer program that permits the interactive simulation of insulin and glucose profiles for teaching, demonstration, and self-learning purposes. Since March/April 1996 it has been made freely available on the Internet as a noncommercial contribution to continuing diabetes education. Up to May 2003 well over 320,000 visits have been logged at the main AIDA Website--www.2aida.org--and over 65,000 copies of the AIDA program have been downloaded free-of-charge. This review (the second of two parts) overviews research projects and ventures, undertaken for the most part by other research workers in the diabetes computing field, that have made use of the freeware AIDA program. As with Part 1 of the review (Diabetes Technol Ther 2003;5:425-438) relevant research work was identified in three main ways: (i) by personal (e-mail/written) communications from researchers, (ii) via the ISI Web of Science citation database to identify published articles which referred to AIDA-related papers, and (iii) via searches on the Internet. Also, in a number of cases research students who had sought advice about AIDA, and diabetes computing in general, provided copies of their research dissertations/theses upon the completion of their projects. Part 2 of this review highlights some more of the research projects that have made use of the AIDA diabetes simulation program to date. A wide variety of diabetes computing topics are addressed. These range from learning about parameter interactions using simulated blood glucose data, to considerations of dietary assessments, developing new diabetes models, and performance monitoring of closed-loop insulin delivery devices. Other topics include evaluation/validation research usage of such software, applying simulated blood glucose data for prototype training/validation, and other research uses of placing technical information on the Web. This review confirms an unexpected but useful benefit of distributing a medical program, like AIDA, for free via the Internet--demonstrating how it is possible to have a synergistic benefit with other researchers--facilitating their own research projects in related medical fields. A common theme that emerges from the research ventures that have been reviewed is the use of simulated blood glucose data from the AIDA software for preliminary computer lab-based testing of other decision support prototypes. Issues surrounding such use of simulated data for separate computer prototype testing are considered further.

Habitat Demonstration Unit Project: Leadership and Management Strategies for a Rapid Prototyping Project

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Toup, Larry; Gill, Tracy; Tri, Terry; Howe, Scott; Smitherman, David

2011-01-01

This paper gives an overview of the National Aeronautics and Space Administration (NASA) led multi-center Habitat Demonstration Unit (HDU) project leadership and management strategies being used by the NASA HDU team for a rapid prototyping project. The HDU project team constructed and tested an analog prototype lunar surface habitat/laboratory called the Pressurized Excursion Module (PEM) during 2010. The prototype unit subsystems were integrated in a short amount of time, utilizing a tiger team rapid prototyping approach that brought together over 20 habitation-related technologies and innovations from a variety of NASA centers. This paper describes the leadership and management strategies as well as lessons learned pertaining to leading and managing a multi-center diverse team in a rapid prototype environment. The PEM configuration went from a paper design to an operational surface habitat demonstration unit in less than 12 months. The HDU project is part of the strategic plan from the Exploration Systems Mission Directorate (ESMD) Directorate Integration Office (DIO) and the Exploration Mission Systems Office (EMSO) to test destination elements in analog environments. The 2011 HDU-Deep Space Habitat (DSH) configuration will build upon the PEM work, and emphasize validity of crew operations (remote working and living), EVA operations, mission operations, logistics operations, and science operations that might be required in a deep space context for Near Earth Object (NEO) exploration mission architectures. The 2011 HDU-DSH will be field-tested during the 2011 Desert Research and Technologies Studies (DRaTS) field tests. The HDU project is a "technology-pull" project that integrates technologies and innovations from multiple NASA centers. This project will repurpose the HDU 2010 demo unit that was field tested in the 2010 DRaTS, adding habitation functionality to the prototype unit. This paper will describe the strategy of establishing a multi-center project management team that put in place the key multi-center leadership skills and disciplines to enable a successful tiger team approach. Advocacy was established with key stakeholders and NASA Headquarters (HQ) by defining a strategic vision, mission, goals and objectives for the project and team. As a technology-pull testbed capability the HDU project was able to collaborate and leverage the Exploration Technology Development Program (ETDP) and individual NASA center investments which capitalized on their respective center core competencies and skills. This approach enable the leveraging of over $7.5m of value to create an operational habitat demonstration unit 2010 PEM configuration.

Carbon Capture and Sequestration from a Hydrogen Production Facility in an Oil Refinery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Engels, Cheryl; Williams, Bryan, Valluri, Kiranmal; Watwe, Ramchandra

2010-06-21

The project proposed a commercial demonstration of advanced technologies that would capture and sequester CO2 emissions from an existing hydrogen production facility in an oil refinery into underground formations in combination with Enhanced Oil Recovery (EOR). The project is led by Praxair, Inc., with other project participants: BP Products North America Inc., Denbury Onshore, LLC (Denbury), and Gulf Coast Carbon Center (GCCC) at the Bureau of Economic Geology of The University of Texas at Austin. The project is located at the BP Refinery at Texas City, Texas. Praxair owns and operates a large hydrogen production facility within the refinery. Asmore » part of the project, Praxair would construct a CO2 capture and compression facility. The project aimed at demonstrating a novel vacuum pressure swing adsorption (VPSA) based technology to remove CO2 from the Steam Methane Reformers (SMR) process gas. The captured CO2 would be purified using refrigerated partial condensation separation (i.e., cold box). Denbury would purchase the CO2 from the project and inject the CO2 as part of its independent commercial EOR projects. The Gulf Coast Carbon Center at the Bureau of Economic Geology, a unit of University of Texas at Austin, would manage the research monitoring, verification and accounting (MVA) project for the sequestered CO2, in conjunction with Denbury. The sequestration and associated MVA activities would be carried out in the Hastings field at Brazoria County, TX. The project would exceed DOE?s target of capturing one million tons of CO2 per year (MTPY) by 2015. Phase 1 of the project (Project Definition) is being completed. The key objective of Phase 1 is to define the project in sufficient detail to enable an economic decision with regard to proceeding with Phase 2. This topical report summarizes the administrative, programmatic and technical accomplishments completed in Phase 1 of the project. It describes the work relative to project technical and design activities (associated with CO2 capture technologies and geologic sequestration MVA), and Environmental Information Volume. Specific accomplishments of this Phase include: 1. Finalization of the Project Management Plan 2. Development of engineering designs in sufficient detail for defining project performance and costs 3. Preparation of Environmental Information Volume 4. Completion of Hazard Identification Studies 5. Completion of control cost estimates and preparation of business plan During the Phase 1 detailed cost estimate, project costs increased substantially from the previous estimate. Furthermore, the detailed risk assessment identified integration risks associated with potentially impacting the steam methane reformer operation. While the Phase 1 work identified ways to mitigate these integration risks satisfactorily from an operational perspective, the associated costs and potential schedule impacts contributed to the decision not to proceed to Phase 2. We have concluded that the project costs and integration risks at Texas City are not commensurate with the potential benefits of the project at this time.« less

Renewable Energy From Animal Biomass – Farm Methane

DOE Office of Scientific and Technical Information (OSTI.GOV)

St. Amour, Kenneth

2013-08-31

The major goal of the project is to develop 2 anaerobic digesters on family farms in rural Vermont. We have accomplished half of that goal, with 1 digester operating on the Gebbie Maplehurst Farm in Greensboro, Vermont. The 2nd digester is planned as a student demonstration unit at Vermont Technical College in Randolph Center, Vermont. That half of the project has not commenced. We will limit our discussion to the Gebbie Maplehurst Farm project. A 150MW generator is installed on the farm and is producing electricity which is being sold as part of the Standard Offer Program within the Statemore » of Vermont. The induction generator is the first of its kind manufactured by Martin Machinery of Latham, Missouri. The project is currently generating approximately 15% - 20% of the capacity as shown in appendix I. However, it is anticipated that details will quickly be worked out to increase that capacity factor.« less

Project Adopsys as an example of international collaboration in the field of photonics

NASA Astrophysics Data System (ADS)

Zoric, Nenad; Livshits, Irina; Urbach, Paul

2015-01-01

Tendencies of international cooperation in engineering education became very visible during recent years. We demonstrate this statement on one currently running EU project ADOPSYS in the field of optical design, which is an important part of engineering education in photonics. This example shows the importance of the input from different countries and organizations - both from industry and academia. Seven universities and eight optical companies are involved in the project ADOPSYS. Sharing experience of Academia education activity we provide new international type of education "free-of borders". We are going to discuss the key enable technology - PHOTONICS, which is widely used in modern society. Engineering science became very international. For communicating between people from different countries the English language is now used almost exclusively. For a fruitful collaboration between people from different nations, in multi-national projects, tolerance and respect are required between people of different political, cultural, educational backgrounds.

KSC-2012-1564

NASA Image and Video Library

2012-02-23

ORLANDO, Fla. – Students from Meadow Woods Middle School in Orlando take part in a hands-on activity during NASA’s Project Management PM Challenge 2012. Education specialists from NASA’s Kennedy Space Center supported the annual PM Challenge with demonstrations designed to illustrate various principles of physics. The demonstrations are designed to increase student interest and pursuit of the science, technology, engineering and mathematics STEM fields integral to producing the next generation of scientists and engineers. PM Challenge 2012 was held at the Caribe Royale Hotel and Convention Center in Orlando, Fla., on Feb. 22-23, to provide a forum for all stakeholders in the project management community to meet and share stories, lessons learned and new uses of technology in the industry. The PM Challenge is sponsored by NASA's Office of the Chief Engineer. For additional information, visit http://www.nasa.gov/offices/oce/pmchallenge/index.html. Photo credit: NASA/Jim Grossmann

OpenMDAO: Framework for Flexible Multidisciplinary Design, Analysis and Optimization Methods

NASA Technical Reports Server (NTRS)

Heath, Christopher M.; Gray, Justin S.

2012-01-01

The OpenMDAO project is underway at NASA to develop a framework which simplifies the implementation of state-of-the-art tools and methods for multidisciplinary design, analysis and optimization. Foremost, OpenMDAO has been designed to handle variable problem formulations, encourage reconfigurability, and promote model reuse. This work demonstrates the concept of iteration hierarchies in OpenMDAO to achieve a flexible environment for supporting advanced optimization methods which include adaptive sampling and surrogate modeling techniques. In this effort, two efficient global optimization methods were applied to solve a constrained, single-objective and constrained, multiobjective version of a joint aircraft/engine sizing problem. The aircraft model, NASA's nextgeneration advanced single-aisle civil transport, is being studied as part of the Subsonic Fixed Wing project to help meet simultaneous program goals for reduced fuel burn, emissions, and noise. This analysis serves as a realistic test problem to demonstrate the flexibility and reconfigurability offered by OpenMDAO.

The Western Environmental Technology Office (WETO), Butte, Montana. Technology summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

The Western Environmental Technology Office (WETO) is a multi-purpose engineering test facility located in Butte, Montana, and is managed by MSE, Inc. WETO seeks to contribute to environmental research by emphasizing projects to develop heavy metals removal and recovery processes, thermal vitrification systems, and waste minimization/pollution prevention technologies. WETO`s environmental technology research and testing activities focus on the recovery of usable resources from waste. In one of WETO`s areas of focus, groundwater contamination, water from the Berkeley Pit, located near the WETO site, is being used in demonstrations directed toward the recovery of potable water and metal from the heavymore » metal-bearing water. The Berkeley Pit is part of an inactive copper mine near Butte that was once part of the nation`s largest open-pit mining operation. The Pit contains approximately 25 billion gallons of Berkeley Pit groundwater and surface water containing many dissolved minerals. As part of DOE/OST`s Resource Recovery Project (RRP), technologies are being demonstrated to not only clean the contaminated water but to recover metal values such as copper, zinc, and iron with an estimated gross value of more than $100 million. When recovered, the Berkeley Pit waters could benefit the entire Butte valley with new water resources for fisheries, irrigation, municipal, and industrial use. At WETO, the emphasis is on environmental technology development and commercialization activities, which will focus on mine cleanup, waste treatment, resource recovery, and water resource management.« less

Superfast 3D shape measurement of a flapping flight process with motion based segmentation

NASA Astrophysics Data System (ADS)

Li, Beiwen

2018-02-01

Flapping flight has drawn interests from different fields including biology, aerodynamics and robotics. For such research, the digital fringe projection technology using defocused binary image projection has superfast (e.g. several kHz) measurement capabilities with digital-micromirror-device, yet its measurement quality is still subject to the motion of flapping flight. This research proposes a novel computational framework for dynamic 3D shape measurement of a flapping flight process. The fast and slow motion parts are separately reconstructed with Fourier transform and phase shifting. Experiments demonstrate its success by measuring a flapping wing robot (image acquisition rate: 5000 Hz; flapping speed: 25 cycles/second).

ATM Technology Demonstration 1 (ATD-1) Project: Terminal Airspace Technologies for NextGen (Public)

NASA Technical Reports Server (NTRS)

Robinson, John E.; Wang, Easter

2015-01-01

This video highlights the human-in-the-loop (HITL) simulations conducted by the ATD-1 project and features visual elements developed for Traffic Management Advisor - Terminal Metering, Controller Managed Spacing, and Flight Deck Interval Management. The video content is fairly technical and intended for audiences that have some knowledge of air traffic management issues. This includes researchers and management from NASA, FAA, industry partners, and others interested in terminal metering, controller managed spacing, and interval management technologies. Please note that the media release only clears the video for peer audiences such as ATM conferences or as part of presentations to researchers.

The Use of Radar to Improve Rainfall Estimation over the Tennessee and San Joaquin River Valleys

NASA Technical Reports Server (NTRS)

Petersen, Walter A.; Gatlin, Patrick N.; Felix, Mariana; Carey, Lawrence D.

2010-01-01

This slide presentation provides an overview of the collaborative radar rainfall project between the Tennessee Valley Authority (TVA), the Von Braun Center for Science & Innovation (VCSI), NASA MSFC and UAHuntsville. Two systems were used in this project, Advanced Radar for Meteorological & Operational Research (ARMOR) Rainfall Estimation Processing System (AREPS), a demonstration project of real-time radar rainfall using a research radar and NEXRAD Rainfall Estimation Processing System (NREPS). The objectives, methodology, some results and validation, operational experience and lessons learned are reviewed. The presentation. Another project that is using radar to improve rainfall estimations is in California, specifically the San Joaquin River Valley. This is part of a overall project to develop a integrated tool to assist water management within the San Joaquin River Valley. This involves integrating several components: (1) Radar precipitation estimates, (2) Distributed hydro model, (3) Snowfall measurements and Surface temperature / moisture measurements. NREPS was selected to provide precipitation component.

Synergy of Earth Observation and In-Situ Monitoring Data for Flood Hazard Early Warning System

NASA Astrophysics Data System (ADS)

Brodsky, Lukas; Kodesova, Radka; Spazierova, Katerina

2010-12-01

In this study, we demonstrate synergy of EO and in-situ monitoring data for early warning flood hazard system in the Czech Republic developed within ESA PECS project FLOREO. The development of the demonstration system is oriented to support existing monitoring activities, especially snow melt and surface water runoff contributing to flooding events. The system consists of two main parts accordingly, the first is snow cover and snow melt monitoring driven mainly by EO data and the other is surface water runoff modeling and monitoring driven by synergy of in-situ and EO data.

Construction in space - Toward a fresh definition of the man/machine relation

NASA Technical Reports Server (NTRS)

Watters, H. H.; Stokes, J. W.

1979-01-01

The EVA (extravehicular activity) project forming part of the space construction process is reviewed. The manual EVA constuction, demonstrated by the crew of Skylab 3 by assembling a modest space structure in the form of the twin-pole sunshade, is considered, indicating that the experiment dispelled many doubts about man's ability to execute routine and contingency EVA operations. Tests demonstrating the feasibility of remote teleoperator rendezvous, station keeping, and docking operations, using hand controllers for direct input and television for feedback, are noted. Future plans for designing space construction machines are mentioned.

Social health maintenance organizations' service use and costs, 1985-89

PubMed Central

Harrington, Charlene; Newcomer, Robert J.

1991-01-01

Presented in this article are aggregate utilization and financial data from the four social health maintenance organization (SIHMO) demonstrations that were collected and analyzed as a part of the national evaluation of the SIHMO demonstration project conducted for the Health Care Financing Administration. The S/HMOs, in offering a $6,500 to $12,000 chronic care benefit in addition to the basic HMO benefit package, had higher startup costs and financial losses over the first 5 years than expected, and controlling costs continues to be a challenge to the sites and their sponsors. PMID:10113612

76 FR 12081 - Notice of Two-Year Continuation of Disease Management Demonstration Project for TRICARE Standard...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... Management Demonstration Project for TRICARE Standard Beneficiaries AGENCY: Department of Defense. ACTION: Notice of Two-Year Continuation of Disease Management Demonstration Project for TRICARE Standard... System (MHS) demonstration project entitled ``Disease Management Demonstration Project for TRICARE...

Review of advanced radiator technologies for spacecraft power systems and space thermal control

NASA Technical Reports Server (NTRS)

Juhasz, Albert J.; Peterson, George P.

1994-01-01

A two-part overview of progress in space radiator technologies is presented. The first part reviews and compares the innovative heat-rejection system concepts proposed during the past decade, some of which have been developed to the breadboard demonstration stage. Included are space-constructable radiators with heat pipes, variable-surface-area radiators, rotating solid radiators, moving-belt radiators, rotating film radiators, liquid droplet radiators, Curie point radiators, and rotating bubble-membrane radiators. The second part summarizes a multielement project including focused hardware development under the Civil Space Technology Initiative (CSTI) High Capacity Power program carried out by the NASA Lewis Research Center and its contractors to develop lightweight space radiators in support of Space Exploration Initiative (SEI) power systems technology.

Evolution and outcomes of a quality improvement program.

PubMed

Thor, Johan; Herrlin, Bo; Wittlöv, Karin; Øvretveit, John; Brommels, Mats

2010-01-01

The purpose of this paper is to examine the outcomes and evolution over a five-year period of a Swedish university hospital quality improvement program in light of enduring uncertainty regarding the effectiveness of such programs in healthcare and how best to evaluate it. The paper takes the form of a case study, using data collected as part of the program, including quality indicators from clinical improvement projects and participants' program evaluations. Overall, 58 percent of the program's projects (39/67) demonstrated success. A greater proportion of projects led by female doctors demonstrated success (91 percent, n=11) than projects led by male doctors (51 percent, n=55). Facilitators at the hospital continuously adapted the improvement methods to the local context. A lack of dedicated time for improvement efforts was the participants' biggest difficulty. The dominant benefits included an increased ability to see the "bigger picture" and the improvements achieved for patients and employees. Quality measurement, which is important for conducting and evaluating improvement efforts, was weak with limited reliability. Nevertheless, the present study adds evidence about the effectiveness of healthcare improvement programs. Gender differences in improvement team leadership merit further study. Improvement program evaluation should assess the extent to which improvement methods are locally adapted and applied. This case study reports the outcomes of all improvement projects undertaken in one healthcare organization over a five-year period and provides in-depth insight into an improvement program's changeable nature.

Engagement of groups in family medicine board maintenance of certification.

PubMed

Fisher, Dena M; Brenner, Christopher J; Cheren, Mark; Stange, Kurt C

2013-01-01

The American Board of Medical Specialties' Performance in Practice ("Part IV") portion of Maintenance of Certification (MOC) requirement provides an opportunity for practicing physicians to demonstrate quality improvement (QI) competence. However, specialty boards' certification of one physician at a time does not tap into the potential of collective effort. This article shares learning from a project to help family physicians work in groups to meet their Part IV MOC requirement. A year-long implementation and evaluation project was conducted. Initially, 348 members of a regional family physician organization were invited to participate. A second path was established through 3 health care systems and a county-wide learning collaborative. Participants were offered (1) a basic introduction to QI methods, (2) the option of an alternative Part IV MOC module using a patient experience survey to guide QI efforts, (3) practice-level improvement coaching, (4) support for collaboration and co-learning, and (5) provision of QI resources. More physicians participated through group (66) than individual (12) recruitment, for a total of 78 physicians in 20 practices. Participation occurred at 3 levels: individual, intrapractice, and interpractice. Within the 1-year time frame, intrapractice collaboration occurred most frequently. Interpractice and system-level collaboration has begun and continues to evolve. Physicians felt that they benefited from access to a practice coach and group process. Practice-level collaboration, access to a practice coach, flexibility in choosing and focusing improvement projects, tailored support, and involvement with professional affiliations can enhance the Part IV MOC process. Specialty boards are likely to discover productive opportunities from working with practices, professional organizations, and health care systems to support intra- and interpractice collaborative QI work that uses Part IV MOC requirements to motivate practice improvement.

Standard biological parts knowledgebase.

PubMed

Galdzicki, Michal; Rodriguez, Cesar; Chandran, Deepak; Sauro, Herbert M; Gennari, John H

2011-02-24

We have created the Knowledgebase of Standard Biological Parts (SBPkb) as a publically accessible Semantic Web resource for synthetic biology (sbolstandard.org). The SBPkb allows researchers to query and retrieve standard biological parts for research and use in synthetic biology. Its initial version includes all of the information about parts stored in the Registry of Standard Biological Parts (partsregistry.org). SBPkb transforms this information so that it is computable, using our semantic framework for synthetic biology parts. This framework, known as SBOL-semantic, was built as part of the Synthetic Biology Open Language (SBOL), a project of the Synthetic Biology Data Exchange Group. SBOL-semantic represents commonly used synthetic biology entities, and its purpose is to improve the distribution and exchange of descriptions of biological parts. In this paper, we describe the data, our methods for transformation to SBPkb, and finally, we demonstrate the value of our knowledgebase with a set of sample queries. We use RDF technology and SPARQL queries to retrieve candidate "promoter" parts that are known to be both negatively and positively regulated. This method provides new web based data access to perform searches for parts that are not currently possible.

Towards a fair consideration of PrEP as part of combination HIV prevention in Latin America

PubMed Central

Ravasi, Giovanni; Grinsztejn, Beatriz; Baruch, Ricardo; Guanira, Juan Vicente; Luque, Ricardo; Cáceres, Carlos F; Ghidinelli, Massimo

2016-01-01

Introduction Despite progress in scaling up antiretroviral treatment, HIV prevention strategies have not been successful in significantly curbing HIV incidence in Latin America. HIV prevention interventions need to be expanded to target the most affected key populations with a combination approach, including new high impact technologies. Oral pre-exposure prophylaxis (PrEP) is recommended as additional prevention choice for individuals at higher risk of infection and could become a cost-effective prevention tool. We discuss the barriers and solutions for a fair consideration of PrEP as part of combination HIV prevention strategies in Latin America. Discussion Although demonstration projects are ongoing or being planned in a number of countries, to date no Latin American country has implemented a public PrEP programme. The knowledge of policymakers about PrEP implementation needs to be strengthened, and programmatic guidance and cost estimate tools need to be developed to support adequate planning. Despite high levels of awareness among health providers, especially if engaged in HIV or key population care, willingness to prescribe PrEP is still low due to the lack of national policies and guidelines. Key populations, especially men who have sex with men, transgender women and sex workers, have been engaged in demonstration projects, and qualitative research shows high awareness and willingness to use PrEP, especially if accessible in the public sector for free or at affordable price. Concerns of safety, adherence, effectiveness and risk compensation need to be addressed through targeted social communication strategies to improve PrEP knowledge and stimulate demand. Alliance among policymakers, civil society and representatives from key populations, healthcare providers and researchers will be critical for the design and successful implementation of PrEP demonstration projects of locally adapted delivery models. The use of mechanisms of joint negotiation and procurement of antiretrovirals could reduce costs and significantly increase the cost-effectiveness of PrEP. Conclusions PrEP is an additional prevention tool and should be implemented in combination and synergy with other prevention interventions. PrEP programmes should target high-risk individuals from key populations for higher cost-effectiveness. Demonstration projects may generate strategic information for and lead to the implementation of full-scale PrEP programmes. PMID:27760687

Towards a fair consideration of PrEP as part of combination HIV prevention in Latin America.

PubMed

Ravasi, Giovanni; Grinsztejn, Beatriz; Baruch, Ricardo; Guanira, Juan Vicente; Luque, Ricardo; Cáceres, Carlos F; Ghidinelli, Massimo

2016-01-01

Despite progress in scaling up antiretroviral treatment, HIV prevention strategies have not been successful in significantly curbing HIV incidence in Latin America. HIV prevention interventions need to be expanded to target the most affected key populations with a combination approach, including new high impact technologies. Oral pre-exposure prophylaxis (PrEP) is recommended as additional prevention choice for individuals at higher risk of infection and could become a cost-effective prevention tool. We discuss the barriers and solutions for a fair consideration of PrEP as part of combination HIV prevention strategies in Latin America. Although demonstration projects are ongoing or being planned in a number of countries, to date no Latin American country has implemented a public PrEP programme. The knowledge of policymakers about PrEP implementation needs to be strengthened, and programmatic guidance and cost estimate tools need to be developed to support adequate planning. Despite high levels of awareness among health providers, especially if engaged in HIV or key population care, willingness to prescribe PrEP is still low due to the lack of national policies and guidelines. Key populations, especially men who have sex with men, transgender women and sex workers, have been engaged in demonstration projects, and qualitative research shows high awareness and willingness to use PrEP, especially if accessible in the public sector for free or at affordable price. Concerns of safety, adherence, effectiveness and risk compensation need to be addressed through targeted social communication strategies to improve PrEP knowledge and stimulate demand. Alliance among policymakers, civil society and representatives from key populations, healthcare providers and researchers will be critical for the design and successful implementation of PrEP demonstration projects of locally adapted delivery models. The use of mechanisms of joint negotiation and procurement of antiretrovirals could reduce costs and significantly increase the cost-effectiveness of PrEP. PrEP is an additional prevention tool and should be implemented in combination and synergy with other prevention interventions. PrEP programmes should target high-risk individuals from key populations for higher cost-effectiveness. Demonstration projects may generate strategic information for and lead to the implementation of full-scale PrEP programmes.

The Earth System Documentation (ES-DOC) project

NASA Astrophysics Data System (ADS)

Murphy, S.; Greenslade, M. A.; Treshansky, A.; DeLuca, C.; Guilyardi, E.; Denvil, S.

2013-12-01

Earth System Documentation (ES-DOC) is an international project supplying high quality tools and services in support of Earth system documentation creation, analysis and dissemination. It is nurturing a sustainable standards based documentation ecosystem that aims to become an integral part of the next generation of exa-scale dataset archives. ES-DOC leverages open source software, and applies a software development methodology that places end-user narratives at the heart of all it does. ES-DOC has initially focused upon nurturing the Earth System Model (ESM) documentation eco-system. Within this context ES-DOC leverages the emerging Common Information Model (CIM) metadata standard, which has supported the following projects: ** Coupled Model Inter-comparison Project Phase 5 (CMIP5); ** Dynamical Core Model Inter-comparison Project (DCMIP-2012); ** National Climate Predictions and Projections Platforms (NCPP) Quantitative Evaluation of Downscaling Workshop (QED-2013). This presentation will introduce the project to a wider audience and will demonstrate the current production level capabilities of the eco-system: ** An ESM documentation Viewer embeddable into any website; ** An ESM Questionnaire configurable on a project by project basis; ** An ESM comparison tool reusable across projects; ** An ESM visualization tool reusable across projects; ** A search engine for speedily accessing published documentation; ** Libraries for streamlining document creation, validation and publishing pipelines.

HELICoiD project: a new use of hyperspectral imaging for brain cancer detection in real-time during neurosurgical operations

NASA Astrophysics Data System (ADS)

Fabelo, Himar; Ortega, Samuel; Kabwama, Silvester; Callico, Gustavo M.; Bulters, Diederik; Szolna, Adam; Pineiro, Juan F.; Sarmiento, Roberto

2016-05-01

Hyperspectral images allow obtaining large amounts of information about the surface of the scene that is captured by the sensor. Using this information and a set of complex classification algorithms is possible to determine which material or substance is located in each pixel. The HELICoiD (HypErspectraL Imaging Cancer Detection) project is a European FET project that has the goal to develop a demonstrator capable to discriminate, with high precision, between normal and tumour tissues, operating in real-time, during neurosurgical operations. This demonstrator could help the neurosurgeons in the process of brain tumour resection, avoiding the excessive extraction of normal tissue and unintentionally leaving small remnants of tumour. Such precise delimitation of the tumour boundaries will improve the results of the surgery. The HELICoiD demonstrator is composed of two hyperspectral cameras obtained from Headwall. The first one in the spectral range from 400 to 1000 nm (visible and near infrared) and the second one in the spectral range from 900 to 1700 nm (near infrared). The demonstrator also includes an illumination system that covers the spectral range from 400 nm to 2200 nm. A data processing unit is in charge of managing all the parts of the demonstrator, and a high performance platform aims to accelerate the hyperspectral image classification process. Each one of these elements is installed in a customized structure specially designed for surgical environments. Preliminary results of the classification algorithms offer high accuracy (over 95%) in the discrimination between normal and tumour tissues.

Alkali Metal Heat Pipe Life Issues

NASA Technical Reports Server (NTRS)

Reid, Robert S.

2004-01-01

One approach to space fission power system design is predicated on the use of alkali metal heat pipes, either as radiator elements, thermal management components, or as part of the core primary heat-transfer system. This synopsis characterizes long-life core heat pipes. References are included where more detailed information can be found. Specifics shown here are for demonstrational purposes and do not necessarily reflect current Project Prometheus point designs.

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure . Part II; Severe Damage

NASA Technical Reports Server (NTRS)

Przekop, Adam; Jegley, Dawn C.; Lovejoy, Andrew E.; Rouse, Marshall; Wu, Hsi-Yung T.

2016-01-01

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a finite element analysis and the testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part II of the paper considers the final test to failure of the test article in the presence of an intentionally inflicted severe discrete source damage under the wing up-bending loading condition. Finite element analysis results are compared with measurements acquired during the test and demonstrate that the hybrid wing body test article was able to redistribute and support the required design loads in a severely damaged condition.

Test development for the thermionic system evaluation test (TSET) project

NASA Astrophysics Data System (ADS)

Morris, D. Brent; Standley, Vaughn H.; Schuller, Michael J.

1992-01-01

The arrival of a Soviet TOPAZ-II space nuclear reactor affords the US space nuclear power (SNP) community the opportunity to study an assembled thermionic conversion power system. The TOPAZ-II will be studied via the Thermionic System Evaluation Test (TSET) Project. This paper is devoted to the discussion of TSET test development as related to the objectives contained in the TSET Project Plan (Standley et al. 1991). The objectives contained in the Project Plan are the foundation for scheduled TSET tests on TOPAZ-II and are derived from the needs of the Air Force Thermionic SNP program. Our ability to meet the objectives is bounded by unique constraints, such as procurement requirements, operational limitations, and necessary interaction between US and Soviet Scientists and engineers. The fulfillment of the test objectives involves a thorough methodology of test scheduling and data managment. The overall goals for the TSET program are gaining technical understanding of a thermionic SNP system and demonstrating the capabilities and limitations of such a system while assisting in the training of US scientist and engineers in preparation for US SNP system testing. Tests presently scheduled as part of TSET include setup, demonstration, and verification tests; normal and off-normal operating test, and system and component performance tests.

NEXT Single String Integration Test Results

NASA Technical Reports Server (NTRS)

Soulas, George C.; Patterson, Michael J.; Pinero, Luis; Herman, Daniel A.; Snyder, Steven John

2010-01-01

As a critical part of NASA's Evolutionary Xenon Thruster (NEXT) test validation process, a single string integration test was performed on the NEXT ion propulsion system. The objectives of this test were to verify that an integrated system of major NEXT ion propulsion system elements meets project requirements, to demonstrate that the integrated system is functional across the entire power processor and xenon propellant management system input ranges, and to demonstrate to potential users that the NEXT propulsion system is ready for transition to flight. Propulsion system elements included in this system integration test were an engineering model ion thruster, an engineering model propellant management system, an engineering model power processor unit, and a digital control interface unit simulator that acted as a test console. Project requirements that were verified during this system integration test included individual element requirements ; integrated system requirements, and fault handling. This paper will present the results of these tests, which include: integrated ion propulsion system demonstrations of performance, functionality and fault handling; a thruster re-performance acceptance test to establish baseline performance: a risk-reduction PMS-thruster integration test: and propellant management system calibration checks.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Udengaard, Niels; Knight, Richard; Wendt, Jesper

This final report presents the results of a four-year technology demonstration project carried out by a consortium of companies sponsored in part by a $25 million funding by the Department of Energy (DOE) under the American Recovery and Reinvestment Act (ARRA). The purpose of the project was to demonstrate a new, economical technology for the thermochemical conversion of woody biomass into gasoline and to demonstrate that the gasoline produced in this way is suitable for direct inclusion in the already existing gasoline pool. The process that was demonstrated uses the Andritz-Carbona fluidized-bed steam-oxygen gasification technology and advanced tar reforming catalyticmore » systems to produce a clean syngas from waste wood, integrated conventional gas cleanup steps, and finally utilizes Haldor Topsoe’s (Topsoe) innovative Topsoe Improved Gasoline Synthesis (TIGASTM) syngas-to-gasoline process. Gas Technology Institute (GTI) carried out the bulk of the testing work at their Flex Fuel development facility in Des Plaines, Illinois; UPM in Minnesota supplied and prepared the feedstocks, and characterization of liquid products was conducted in Phillips 66 labs in Oklahoma. The produced gasoline was used for a single-engine emission test at Southwest Research Institute (SwRI®) in San Antonio, TX, as well as in a fleet test at Transportation Research Center, Inc. (TRC Inc.) in East Liberty, Ohio. The project benefited from the use of existing pilot plant equipment at GTI, including a 21.6 bone dry short ton/day gasifier, tar reformer, Morphysorb® acid gas removal, associated syngas cleanup and gasifier feeding and oxygen systems.« less

DARPA/USAF/USN J-UCAS X-45A System Demonstration Program: A Review of Flight Test Site Processes and Personnel

NASA Technical Reports Server (NTRS)

Cosentino, Gary B.

2008-01-01

The Joint Unmanned Combat Air Systems (J-UCAS) program is a collaborative effort between the Defense Advanced Research Project Agency (DARPA), the US Air Force (USAF) and the US Navy (USN). Together they have reviewed X-45A flight test site processes and personnel as part of a system demonstration program for the UCAV-ATD Flight Test Program. The goal was to provide a disciplined controlled process for system integration and testing and demonstration flight tests. NASA's Dryden Flight Research Center (DFRC) acted as the project manager during this effort and was tasked with the responsibilities of range and ground safety, the provision of flight test support and infrastructure and the monitoring of technical and engineering tasks. DFRC also contributed their engineering knowledge through their contributions in the areas of autonomous ground taxi control development, structural dynamics testing and analysis and the provision of other flight test support including telemetry data, tracking radars, and communications and control support equipment. The Air Force Flight Test Center acted at the Deputy Project Manager in this effort and was responsible for the provision of system safety support and airfield management and air traffic control services, among other supporting roles. The T-33 served as a J-UCAS surrogate aircraft and demonstrated flight characteristics similar to that of the the X-45A. The surrogate served as a significant risk reduction resource providing mission planning verification, range safety mission assessment and team training, among other contributions.

5 CFR 470.305 - Submission of proposals for demonstration projects.

Code of Federal Regulations, 2010 CFR

2010-01-01

... projects. 470.305 Section 470.305 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PERSONNEL MANAGEMENT RESEARCH PROGRAMS AND DEMONSTRATIONS PROJECTS Regulatory Requirements Pertaining to Demonstration Projects § 470.305 Submission of proposals for demonstration projects. (a) OPM...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickerson, Patricia O'Donnell; Summa, Deborah Ann; Liu, Cheng

The goals of this project were to demonstrate reliable, reproducible solid state bonding of aluminum 6061 alloy plates together to encapsulate DU-10 wt% Mo surrogate fuel foils. This was done as part of the CONVERT Fuel Fabrication Capability effort in Process Baseline Development . Bonding was done using Hot Isotatic Pressing (HIP) of evacuated stainless steel cans (a.k.a HIP cans) containing fuel plate components and strongbacks. Gross macroscopic measurements of HIP cans prior to HIP and after HIP were used as part of this demonstration, and were used to determine the accuracy of a finitie element model of the HIPmore » bonding process. The quality of the bonding was measured by controlled miniature bulge testing for Al-Al, Al-Zr, and Zr-DU bonds. A special objective was to determine if the HIP process consistently produces good quality bonding and to determine the best characterization techniques for technology transfer.« less

[Old gender patterns still used when physicians are pictured in medical journals. Male physicians are portrayed as active leaders, women physicians as listening, compassionate].

PubMed

Eriksson, Bodil; Johansson, Eva E

As a part of a medical student' s research project on medical socialisation, the 2002 issue of two Swedish medicaljournals, Läkartidningen and Moderna Läkare, were scrutinized regarding how male and female physicians were represented on pictures. The outward façade was mostly male; 87% of portrays of editorials pictured a man, 81% of career announcements displayed men. Authors of articles and chroniclers more often presented a female face (55%). Photos in reports showed around 60% men and 40 % women, both regarding area and number of photos. These shares corresponded well to the actual share of male and female physicians in Sweden. The content analysis of pictures, however, demonstrated gender features: men were to a much higher degree focused in leading, demonstrating and speaker positions, while women to a higher degree were portrayed as taking part in consultations or caring activities.

Vision Algorithms to Determine Shape and Distance for Manipulation of Unmodeled Objects

NASA Technical Reports Server (NTRS)

Montes, Leticia; Bowers, David; Lumia, Ron

1998-01-01

This paper discusses the development of a robotic system for general use in an unstructured environment. This is illustrated through pick and place of randomly positioned, un-modeled objects. There are many applications for this project, including rock collection for the Mars Surveyor Program. This system is demonstrated with a Puma560 robot, Barrett hand, Cognex vision system, and Cimetrix simulation and control, all running on a PC. The demonstration consists of two processes: vision system and robotics. The vision system determines the size and location of the unknown objects. The robotics part consists of moving the robot to the object, configuring the hand based on the information from the vision system, then performing the pick/place operation. This work enhances and is a part of the Low Cost Virtual Collaborative Environment which provides remote simulation and control of equipment.

Management strategies to effect change in intensive care units: lessons from the world of business. Part II. Quality-improvement strategies.

PubMed

Gershengorn, Hayley B; Kocher, Robert; Factor, Phillip

2014-03-01

The success of quality-improvement projects relies heavily on both project design and the metrics chosen to assess change. In Part II of this three-part American Thoracic Society Seminars series, we begin by describing methods for determining which data to collect, tools for data presentation, and strategies for data dissemination. As Avedis Donabedian detailed a half century ago, defining metrics in healthcare can be challenging; algorithmic determination of the best type of metric (outcome, process, or structure) can help intensive care unit (ICU) managers begin this process. Choosing appropriate graphical data displays (e.g., run charts) can prompt discussions about and promote quality improvement. Similarly, dashboards/scorecards are useful in presenting performance improvement data either publicly or privately in a visually appealing manner. To have compelling data to show, ICU managers must plan quality-improvement projects well. The second portion of this review details four quality-improvement tools-checklists, Six Sigma methodology, lean thinking, and Kaizen. Checklists have become commonplace in many ICUs to improve care quality; thinking about how to maximize their effectiveness is now of prime importance. Six Sigma methodology, lean thinking, and Kaizen are techniques that use multidisciplinary teams to organize thinking about process improvement, formalize change strategies, actualize initiatives, and measure progress. None originated within healthcare, but each has been used in the hospital environment with success. To conclude this part of the series, we demonstrate how to use these tools through an example of improving the timely administration of antibiotics to patients with sepsis.

Human Rehabilitation Techniques. Project Papers. Volume IV, Part B.

ERIC Educational Resources Information Center

Dudek, R. A.; And Others

Volume IV, Part B of a six-volume final report (which covers the findings of a research project on policy and technology related to rehabilitation of disabled individuals) presents a continuation of papers (Part A) giving an overview of project methodology, much of the data used in projecting consequences and policymaking impacts in project…

The Mobile Element Locator Tool (MELT): population-scale mobile element discovery and biology

PubMed Central

Gardner, Eugene J.; Lam, Vincent K.; Harris, Daniel N.; Chuang, Nelson T.; Scott, Emma C.; Pittard, W. Stephen; Mills, Ryan E.; Devine, Scott E.

2017-01-01

Mobile element insertions (MEIs) represent ∼25% of all structural variants in human genomes. Moreover, when they disrupt genes, MEIs can influence human traits and diseases. Therefore, MEIs should be fully discovered along with other forms of genetic variation in whole genome sequencing (WGS) projects involving population genetics, human diseases, and clinical genomics. Here, we describe the Mobile Element Locator Tool (MELT), which was developed as part of the 1000 Genomes Project to perform MEI discovery on a population scale. Using both Illumina WGS data and simulations, we demonstrate that MELT outperforms existing MEI discovery tools in terms of speed, scalability, specificity, and sensitivity, while also detecting a broader spectrum of MEI-associated features. Several run modes were developed to perform MEI discovery on local and cloud systems. In addition to using MELT to discover MEIs in modern humans as part of the 1000 Genomes Project, we also used it to discover MEIs in chimpanzees and ancient (Neanderthal and Denisovan) hominids. We detected diverse patterns of MEI stratification across these populations that likely were caused by (1) diverse rates of MEI production from source elements, (2) diverse patterns of MEI inheritance, and (3) the introgression of ancient MEIs into modern human genomes. Overall, our study provides the most comprehensive map of MEIs to date spanning chimpanzees, ancient hominids, and modern humans and reveals new aspects of MEI biology in these lineages. We also demonstrate that MELT is a robust platform for MEI discovery and analysis in a variety of experimental settings. PMID:28855259

76 FR 80907 - TRICARE Prime Urgent Care Demonstration Project

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... DEPARTMENT OF DEFENSE Office of the Secretary TRICARE Prime Urgent Care Demonstration Project....S. Code, section 1092, entitled Department Of Defense TRICARE Prime Urgent Care Demonstration Project. The demonstration project is intended to test whether allowing four visits to an urgent care...

Strategies for improving transportation project delivery performance.

DOT National Transportation Integrated Search

2016-09-01

project delivery performance for the various contracting methods that are : applicable for CTDOTs use. The report is structured in two parts. Part A covers overall : project deliverability and Part B is focused on environmental review processes an...

18 CFR 16.21 - Operation of projects with a minor or minor part license not subject to sections 14 and 15 of the...

Code of Federal Regulations, 2010 CFR

2010-04-01

... with a minor or minor part license not subject to sections 14 and 15 of the Federal Power Act after... TAKEOVER AND RELICENSING OF LICENSED PROJECTS Projects With Minor and Minor Part Licenses Not Subject to Sections 14 and 15 of the Federal Power Act § 16.21 Operation of projects with a minor or minor part...

18 CFR 16.21 - Operation of projects with a minor or minor part license not subject to sections 14 and 15 of the...

Code of Federal Regulations, 2011 CFR

2011-04-01

... with a minor or minor part license not subject to sections 14 and 15 of the Federal Power Act after... TAKEOVER AND RELICENSING OF LICENSED PROJECTS Projects With Minor and Minor Part Licenses Not Subject to Sections 14 and 15 of the Federal Power Act § 16.21 Operation of projects with a minor or minor part...

The WAMI Rural Hospital Project. Part 5: Community perception of local health care services.

PubMed

Hart, L G; Lishner, D M; Amundson, B A

1991-01-01

Rural health care facilities commonly employ community health care surveys as marketing research instruments to assess consumer utilization of and satisfaction with local services. However, there is little information on the use of survey findings as a way to design interventions to enhance consumer satisfaction and hospital viability. A community survey was administered in six Northwest rural communities as part of the Rural Hospital Project (RHP) to identify weaknesses in local health care services, guide remedial activities, act as a catalyst for change, and assess changes in community perceptions following project interventions. Descriptive findings revealed problems typically observed in small rural communities, including relatively low hospital and physician market share, outmigration for certain types of health care not available locally, and dissatisfaction with some aspects of hospital and physician services. Satisfaction with various aspects of care tended to be lower among males, the uninsured, and younger respondents. Comparisons of survey responses before (1985) and after (1989) the RHP generally demonstrated stability in hospital and physician market share, with project hospitals performing well in 1989 in comparison to other rural hospitals of similar size. The percentage of respondents who rated overall quality of local hospital and physician care positively generally increased or remained stable over the study period. Substantial decreases in satisfaction levels were found for access to care. Importantly, gains were made in those areas and services which received particular emphasis in the project.

Non-rigid alignment in electron tomography in materials science.

PubMed

Printemps, Tony; Bernier, Nicolas; Bleuet, Pierre; Mula, Guido; Hervé, Lionel

2016-09-01

Electron tomography is a key technique that enables the visualization of an object in three dimensions with a resolution of about a nanometre. High-quality 3D reconstruction is possible thanks to the latest compressed sensing algorithms and/or better alignment and preprocessing of the 2D projections. Rigid alignment of 2D projections is routine in electron tomography. However, it cannot correct misalignments induced by (i) deformations of the sample due to radiation damage or (ii) drifting of the sample during the acquisition of an image in scanning transmission electron microscope mode. In both cases, those misalignments can give rise to artefacts in the reconstruction. We propose a simple-to-implement non-rigid alignment technique to correct those artefacts. This technique is particularly suited for needle-shaped samples in materials science. It is initiated by a rigid alignment of the projections and it is then followed by several rigid alignments of different parts of the projections. Piecewise linear deformations are applied to each projection to force them to simultaneously satisfy the rigid alignments of the different parts. The efficiency of this technique is demonstrated on three samples, an intermetallic sample with deformation misalignments due to a high electron dose typical to spectroscopic electron tomography, a porous silicon sample with an extremely thin end particularly sensitive to electron beam and another porous silicon sample that was drifting during image acquisitions. © 2016 The Authors Journal of Microscopy © 2016 Royal Microscopical Society.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Audette, L.G.

As originally conceived, the project called for modification of existing, commercially available stoker components. We experienced substantial delays in procurement, caused by supply backlogs and a major fire at the plant which ultimately provided the main stoker frame. Added to the problems was the bankruptcy of the L.W. Gay Stoveworks, where the project was to be located. Ultimately, parts were assembled and a combustion chamber was constructed at the Leyden Energy Corporation of Shelburne Falls, Massachusetts. A firing chamber with provision for measuring various physical and combustion parameters was constructed. The stoker, with appropriate modifications, was installed. Combustion analysis equipmentmore » was procured, and coal and wood pellets were stoked in order to test the effectiveness of the modifications. This report describes the configuration of the demonstration stoker and its modifications, as well as the testing exercise performed over the course of the project. 10 figs.« less

Clinical identification of compensatory structures on projective tests: a self psychological approach.

PubMed

Silverstein, M L

2001-06-01

In this article I discuss compensatory structure, a concept from Kohut's (1971, 1977) psychology of the self that is not as familiar as Kohut's other views about the self. Compensatory structures are attempts to repair selfobject failure, usually by strengthening idealization or twinship in the face of mirroring deficits. Compensatory structures, particularly their early indications, can be detected on projective tests for identifying adaptive resources and treatment potential. The clinical identification of compensatory structures on test findings is described using Rorschach and Thematic Apperception Test (Murray, 1943) content. Particular attention is devoted to the 2-part process of demonstrating first, an injury to the self, and second, how attempts to recover from such injuries can be detected on projective tests. Clinical examples are provided, and the differentiation between compensatory structures and defenses and sublimation is discussed.

Superfast high-resolution absolute 3D recovery of a stabilized flapping flight process.

PubMed

Li, Beiwen; Zhang, Song

2017-10-30

Scientific research of a stabilized flapping flight process (e.g. hovering) has been of great interest to a variety of fields including biology, aerodynamics, and bio-inspired robotics. Different from the current passive photogrammetry based methods, the digital fringe projection (DFP) technique has the capability of performing dense superfast (e.g. kHz) 3D topological reconstructions with the projection of defocused binary patterns, yet it is still a challenge to measure a flapping flight process with the presence of rapid flapping wings. This paper presents a novel absolute 3D reconstruction method for a stabilized flapping flight process. Essentially, the slow motion parts (e.g. body) and the fast-motion parts (e.g. wings) are segmented and separately reconstructed with phase shifting techniques and the Fourier transform, respectively. The topological relations between the wings and the body are utilized to ensure absolute 3D reconstruction. Experiments demonstrate the success of our computational framework by testing a flapping wing robot at different flapping speeds.

Albany v. 3.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salinger, Andrew; Phipps, Eric; Ostien, Jakob

2016-01-13

The Albany code is a general-purpose finite element code for solving partial differential equations (PDEs). Albany is a research code that demonstrates how a PDE code can be built by interfacing many of the open-source software libraries that are released under Sandia's Trilinos project. Part of the mission of Albany is to be a testbed for new Trilinos libraries, to refine their methods, usability, and interfaces. Albany includes hooks to optimization and uncertainty quantification algorithms, including those in Trilinos as well as those in the Dakota toolkit. Because of this, Albany is a desirable starting point for new code developmentmore » efforts that wish to make heavy use of Trilinos. Albany is both a framework and the host for specific finite element applications. These applications have project names, and can be controlled by configuration option when the code is compiled, but are all developed and released as part of the single Albany code base, These include LCM, QCAD, FELIX, Aeras, and ATO applications.« less

Projection Reduction Exposure with Variable Axis Immersion Lenses (PREVAIL)-A High Throughput E-Beam Projection Approach for Next Generation Lithography

NASA Astrophysics Data System (ADS)

Pfeiffer, Hans

1999-12-01

Projection reduction exposure with variable axis immersion lenses (PREVAIL) represents the high throughput e-beam projection approach to next generation lithography (NGL), which IBM is pursuing in cooperation with Nikon Corporation as an alliance partner. This paper discusses the challenges and accomplishments of the PREVAIL project. The supreme challenge facing all e-beam lithography approaches has been and still is throughput. Since the throughput of e-beam projection systems is severely limited by the available optical field size, the key to success is the ability to overcome this limitation. The PREVAIL technique overcomes field-limiting off-axis aberrations through the use of variable axis lenses, which electronically shift the optical axis simultaneously with the deflected beam, so that the beam effectively remains on axis. The resist images obtained with the proof-of-concept (POC) system demonstrate that PREVAIL effectively eliminates off-axis aberrations affecting both the resolution and placement accuracy of pixels. As part of the POC system a high emittance gun has been developed to provide uniform illumination of the patterned subfield, and to fill the large numerical aperture projection optics designed to significantly reduce beam blur caused by Coulombinteraction.

Intermittent sizing on carbon fiber for composite application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Norris, Jr, Robert E.; Paulauskas, Felix L.; Ozcan, Soydan

Intermittent sizing is a technique designed to improve the bonding of carbon fiber to a resin when manufacturing composite parts. The purpose of this technique is to improve Sheet Molding Composites (SMC) made of non-continuous carbon fibers while using regular material. At the end of the project, tests showed that improved mechanical properties have been achieved using this technique compared to conventional process. Mechanical properties have been improved by 110% for the peak tensile stress and by 60% for the modulus at the laboratory scale. In this project, Continental Structural Plastics and ORNL have worked to demonstrate the scalability andmore » viability of commercialization of this technique.« less

ERNIE performance with TSA portals Initial Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Labov, S.

This project extends the “Enhanced Radiological Nuclear Inspection and Evaluation” (ERNIE) system developed with CBP and DNDO to improve performance of PVT-based Radiation Portal Monitors (RPMs). ERNIE was designed to be used with any RPM system. The first implementation was with the SAIC (Leidos) RPM-8 systems. In this project, we are demonstrating how effective the ERNIE approach can be when applied to the VM250 TSA portals used in NSDD programs. Part of the challenge in adapting ERNIE to handle VM250 portals is the lack of gamma spectral information. We report here on the first results showing how the ERNIE analysismore » can improve analysis of measurements with the VM250 RPMs.« less

The Adult Attachment Projective Picture System: integrating attachment into clinical assessment.

PubMed

George, Carol; West, Malcolm

2011-01-01

This article summarizes the development and validation of the Adult Attachment Projective System (AAP), a measure we developed from the Bowlby-Ainsworth developmental tradition to assess adult attachment status. The AAP has demonstrated excellent concurrent validity with the Adult Attachment Interview (George, Kaplan, & Main, 1984/1985/1996; Main & Goldwyn, 1985-1994; Main, Goldwyn, & Hesse, 2003), interjudge reliability, and test-retest reliability, with no effects of verbal intelligence or social desirability. The AAP coding and classification system and application in clinical and community samples are summarized. Finally, we introduce the 3 other articles that are part of this Special Section and discuss the use of the AAP in therapeutic assessment and treatment.

3D-Printed Permanent Magnets Outperform Conventional Versions, Conserve Rare Materials

ScienceCinema

Paranthaman, Parans

2018-06-13

Researchers at the Department of Energy’s Oak Ridge National Laboratory have demonstrated that permanent magnets produced by additive manufacturing can outperform bonded magnets made using traditional techniques while conserving critical materials. The project is part of DOE’s Critical Materials Institute (CMI), which seeks ways to eliminate and reduce reliance on rare earth metals and other materials critical to the success of clean energy technologies.

Hurricane impact and recovery shoreline change analysis of the Chandeleur Islands, Louisiana, USA: 1855 to 2005

USGS Publications Warehouse

Fearnley, Sarah M.; Miner, Michael; Brock, John C.

2011-01-01

Results from historical (1855-2005) shoreline change analysis of the Chandeleur Islands, Louisiana, demonstrate that tropical cyclone frequency dominates the long-term evolution of this barrier-island arc. The detailed results of this study were published in December 2009 as part of a special issue of Geo-Marine Letters that documents early results from the Northern Gulf of Mexico (NGOM) Ecosystem Change and Hazard Susceptibility Project.

GATEWAY Demonstrations: Tuning the Light in Senior Care: Evaluating a Trial LED Lighting System at the ACC Care Center in Sacramento, CA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Robert G.; Wilkerson, Andrea M.; Samla, Connie

The GATEWAY program documented the performance of tunable-white LED lighting systems installed in several spaces within the ACC Care Center, a senior-care facility in Sacramento, CA. The project results included energy savings and improved lighting quality, as well as other possible health-related benefits that may have been attributable, at least in part, to the lighting changes.

Behavioral, Cognitive and Social Science Research in the Military

DTIC Science & Technology

2000-08-01

Education The objective of this project is to demonstrate empirically based cost-effective training strategies , with particular emphasis on how to best ... best to train soldiers for peacekeeping missions and how those techniques differ from training soldiers to take part in war. We want to understand...and formed a new strategic planning process for the entire S&T Program. The foundation of this process is the Defense S&T Strategy , which along with

A method for evaluating the funding of components of natural resource and conservation projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wellington, John F., E-mail: welling@ipfw.edu; Lewis, Stephen A., E-mail: lewis.sa07@gmail.com

Many public and private entities such as government agencies and private foundations have missions related to the improvement, protection, and sustainability of the environment. In pursuit of their missions, they fund projects with related outcomes. Typically, the funding scene consists of scarce funding dollars for the many project requests. In light of funding limitations and funder's search for innovative funding schemes, a method to support the allocation of scarce dollars among project components is presented. The proposed scheme has similarities to methods in the project selection literature but differs in its focus on project components and its connection to andmore » enumeration of the universe of funding possibilities. The value of having access to the universe is demonstrated with illustrations. The presentation includes Excel implementations that should appeal to a broad spectrum of project evaluators and reviewers. Access to the space of funding possibilities facilitates a rich analysis of funding alternatives. - Highlights: • Method is given for allocating scarce funding dollars among competing projects. • Allocations are made to fund parts of projects • Proposed method provides access to the universe of funding possibilities. • Proposed method facilitates a rich analysis of funding possibilities. • Excel spreadsheet implementations are provided.« less

Simulation Based Low-Cost Composite Process Development at the US Air Force Research Laboratory

NASA Technical Reports Server (NTRS)

Rice, Brian P.; Lee, C. William; Curliss, David B.

2003-01-01

Low-cost composite research in the US Air Force Research Laboratory, Materials and Manufacturing Directorate, Organic Matrix Composites Branch has focused on the theme of affordable performance. Practically, this means that we use a very broad view when considering the affordability of composites. Factors such as material costs, labor costs, recurring and nonrecurring manufacturing costs are balanced against performance to arrive at the relative affordability vs. performance measure of merit. The research efforts discussed here are two projects focused on affordable processing of composites. The first topic is the use of a neural network scheme to model cure reaction kinetics, then utilize the kinetics coupled with simple heat transport models to predict, in real-time, future exotherms and control them. The neural network scheme is demonstrated to be very robust and a much more efficient method that mechanistic cure modeling approach. This enables very practical low-cost processing of thick composite parts. The second project is liquid composite molding (LCM) process simulation. LCM processing of large 3D integrated composite parts has been demonstrated to be a very cost effective way to produce large integrated aerospace components specific examples of LCM processes are resin transfer molding (RTM), vacuum assisted resin transfer molding (VARTM), and other similar approaches. LCM process simulation is a critical part of developing an LCM process approach. Flow simulation enables the development of the most robust approach to introducing resin into complex preforms. Furthermore, LCM simulation can be used in conjunction with flow front sensors to control the LCM process in real-time to account for preform or resin variability.

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing

NASA Technical Reports Server (NTRS)

Grady, Joseph E.

2015-01-01

The Non-Metallic Gas Turbine Engine project, funded by NASA Aeronautics Research Institute, represents the first comprehensive evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. This will be achieved by assessing the feasibility of using additive manufacturing technologies to fabricate polymer matrix composite and ceramic matrix composite turbine engine components. The benefits include: 50 weight reduction compared to metallic parts, reduced manufacturing costs, reduced part count and rapid design iterations. Two high payoff metallic components have been identified for replacement with PMCs and will be fabricated using fused deposition modeling (FDM) with high temperature polymer filaments. The CMC effort uses a binder jet process to fabricate silicon carbide test coupons and demonstration articles. Microstructural analysis and mechanical testing will be conducted on the PMC and CMC materials. System studies will assess the benefits of fully nonmetallic gas turbine engine in terms of fuel burn, emissions, reduction of part count, and cost. The research project includes a multidisciplinary, multiorganization NASA - industry team that includes experts in ceramic materials and CMCs, polymers and PMCs, structural engineering, additive manufacturing, engine design and analysis, and system analysis.

A Climatology of Tropospheric CO over the Central and Southeastern United States and the Southwestern Pacific Ocean Derived from Space, Air, and Ground-based Infrared Interferometer Spectra

NASA Technical Reports Server (NTRS)

McMillian, W. Wallace; Strow, L. Larrabee; Revercomb, H.; Knuteson, R.; Thompson, A.

2003-01-01

This final report summarizes all research activities and publications undertaken as part of NASA Atmospheric Chemistry and Modeling Analysis Program (ACMAP) Grant NAG-1-2022, 'A Climatology of Tropospheric CO over the Central and Southeastern United States and the Southwestern Pacific Ocean Derived from Space, Air, and Ground-based Infrared Interferometer Spectra'. Major project accomplishments include: (1) analysis of more than 300,000 AERI spectra from the ARM SGP site yielding a 5-year (1998-2002) timeseries of CO retrievals from the Lamont, OK AERI; (2) development of a prototype CO profile retrieval algorithm for AERI spectra; (3) validation and publication of the first CO retrievals from the Scanning High-resolution Interferometer Sounder (SHIS); and (4) development of a prototype AERI tropospheric O3 retrieval algorithm. Compilation and publication of the 5-year Lamont, OK timeseries is underway including a new collaboration with scientists at the Lawrence Berkeley National Laboratory. Public access to this data will be provided upon article submission. A comprehensive CO analysis of the archive of HIS spectra of remains as the only originally proposed activity with little progress. The greatest challenge faced in this project was motivating the University of Wisconsin Co-Investigators to deliver their archived HIS and AERIOO data along with the requisite temperature and water vapor profiles in a timely manner. Part of the supplied HIS dataset from ASHOE may be analyzed as part of a Master s Thesis under a separate project. Our success with the SAFARI 2000 SHIS CO analysis demonstrates the utility of such aircraft remote sensing data given the proper support from the instrument investigators. In addition to the PI and Co-I s, personnel involved in this CO climatology project include one Post Doctoral Fellow, one Research Scientist, two graduate students, and two undergraduate students. A total of fifteen presentations regarding research related to this project were delivered at eleven different scientific meetings. Thus far, three publications have resulted from this project with another five in preparation. No subject inventions resulted from this research project.

[Pioneering surgical innovations in Germany : Part 2: public funding and origins of surgical innovations].

PubMed

Weber, S; Haverich, A

2016-05-01

In recent years research that conforms with evidence-based medicine (EBM) has been demanded even in surgery. Uniform studies were carried out to prove the benefits of new procedures; however, compared to other research sectors, public third party funding for surgical research was significantly cut back. Collation of special features in surgery with respect to external funding of surgical top level research. Examination of the benefits of a continuous promotion and of organizations involved in research. Part one of this investigation presented the methods used to identify and analyze pioneering research in surgery. Out of a total of 15 revolutionary innovations only 3 projects were financed by external funding and 2 projects received indirect financial support as a result of a cooperation with the medical industry. This demonstrates that the majority of projects were neither directly nor indirectly subsidized. Apart from one instance the majority of innovations were generated by university hospitals highly active in research. In effect, the non-existing external funding for outstanding surgical innovations and hospitals suggests that a reformation of surgical research is required. To strengthen the quality of innovations in surgery a concentration of funding to institutions that are highly active in research makes sense. Institutional funding directly linked to a project should form a key component of support particularly in the early stages of development.

Robust Surface Reconstruction via Laplace-Beltrami Eigen-Projection and Boundary Deformation

PubMed Central

Shi, Yonggang; Lai, Rongjie; Morra, Jonathan H.; Dinov, Ivo; Thompson, Paul M.; Toga, Arthur W.

2010-01-01

In medical shape analysis, a critical problem is reconstructing a smooth surface of correct topology from a binary mask that typically has spurious features due to segmentation artifacts. The challenge is the robust removal of these outliers without affecting the accuracy of other parts of the boundary. In this paper, we propose a novel approach for this problem based on the Laplace-Beltrami (LB) eigen-projection and properly designed boundary deformations. Using the metric distortion during the LB eigen-projection, our method automatically detects the location of outliers and feeds this information to a well-composed and topology-preserving deformation. By iterating between these two steps of outlier detection and boundary deformation, we can robustly filter out the outliers without moving the smooth part of the boundary. The final surface is the eigen-projection of the filtered mask boundary that has the correct topology, desired accuracy and smoothness. In our experiments, we illustrate the robustness of our method on different input masks of the same structure, and compare with the popular SPHARM tool and the topology preserving level set method to show that our method can reconstruct accurate surface representations without introducing artificial oscillations. We also successfully validate our method on a large data set of more than 900 hippocampal masks and demonstrate that the reconstructed surfaces retain volume information accurately. PMID:20624704

Low Cost Polymer heat Exchangers for Condensing Boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butcher, Thomas; Trojanowski, Rebecca; Wei, George

2015-09-30

Work in this project sought to develop a suitable design for a low cost, corrosion resistant heat exchanger as part of a high efficiency condensing boiler. Based upon the design parameters and cost analysis several geometries and material options were explored. The project also quantified and demonstrated the durability of the selected polymer/filler composite under expected operating conditions. The core material idea included a polymer matrix with fillers for thermal conductivity improvement. While the work focused on conventional heating oil, this concept could also be applicable to natural gas, low sulfur heating oil, and biodiesel- although these are considered tomore » be less challenging environments. An extruded polymer composite heat exchanger was designed, built, and tested during this project, demonstrating technical feasibility of this corrosion-resistant material approach. In such flue gas-to-air heat exchangers, the controlling resistance to heat transfer is in the gas-side convective layer and not in the tube material. For this reason, the lower thermal conductivity polymer composite heat exchanger can achieve overall heat transfer performance comparable to a metal heat exchanger. However, with the polymer composite, the surface temperature on the gas side will be higher, leading to a lower water vapor condensation rate.« less

Automotive Stirling Engine Development Project

NASA Technical Reports Server (NTRS)

Ernst, William D.; Shaltens, Richard K.

1997-01-01

The development and verification of automotive Stirling engine (ASE) component and system technology is described as it evolved through two experimental engine designs: the Mod 1 and the Mod 2. Engine operation and performance and endurance test results for the Mod 1 are summarized. Mod 2 engine and component development progress is traced from the original design through hardware development, laboratory test, and vehicle installation. More than 21,000 hr of testing were accomplished, including 4800 hr with vehicles that were driven more dm 59,000 miles. Mod 2 engine dynamometer tests demonstrated that the engine system configuration had accomplished its performance goals for power (60 kW) and efficiency (38.5%) to within a few percent. Tests with the Mod 2 engine installed in a delivery van demonstrated combined metro-highway fuel economy improvements consistent with engine performance goals and the potential for low emission levels. A modified version of the Mod 2 has been identified as a manufacturable design for an ASE. As part of the ASE project, the Industry Test and Evaluation Program (ITEP), NASA Technology Utilization (TU) project, and the industry-funded Stirling Natural Gas Engine program were undertaken to transfer ASE technology to end users. The results of these technology transfer efforts are also summarized.

3D Printing All-Aromatic Polyimides using Mask-Projection Stereolithography: Processing the Nonprocessable.

PubMed

Hegde, Maruti; Meenakshisundaram, Viswanath; Chartrain, Nicholas; Sekhar, Susheel; Tafti, Danesh; Williams, Christopher B; Long, Timothy E

2017-08-01

High-performance, all-aromatic, insoluble, engineering thermoplastic polyimides, such as pyromellitic dianhydride and 4,4'-oxydianiline (PMDA-ODA) (Kapton), exhibit exceptional thermal stability (up to ≈600 °C) and mechanical properties (Young's modulus exceeding 2 GPa). However, their thermal resistance, which is a consequence of the all-aromatic molecular structure, prohibits processing using conventional techniques. Previous reports describe an energy-intensive sintering technique as an alternative technique for processing polyimides with limited resolution and part fidelity. This study demonstrates the unprecedented 3D printing of PMDA-ODA using mask-projection stereolithography, and the preparation of high-resolution 3D structures without sacrificing bulk material properties. Synthesis of a soluble precursor polymer containing photo-crosslinkable acrylate groups enables light-induced, chemical crosslinking for spatial control in the gel state. Postprinting thermal treatment transforms the crosslinked precursor polymer to PMDA-ODA. The dimensional shrinkage is isotropic, and postprocessing preserves geometric integrity. Furthermore, large-area mask-projection scanning stereolithography demonstrates the scalability of 3D structures. These unique high-performance 3D structures offer potential in fields ranging from water filtration and gas separation to automotive and aerospace technologies. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

34 CFR 377.1 - What is the Demonstration Projects to Increase Client Choice Program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 2 2010-07-01 2010-07-01 false What is the Demonstration Projects to Increase Client... PROJECTS TO INCREASE CLIENT CHOICE PROGRAM General § 377.1 What is the Demonstration Projects to Increase Client Choice Program? The Demonstration Projects to Increase Client Choice Program is designed to...

Brain stem origins of spinal projections in the lizard Tupinambis nigropunctatus.

PubMed

Cruce, W L; Newman, D B

1981-05-10

In order to study brainstem origins of spinal projections, ten Tegu lizards (Tupinambis nigropunctatus) received complete or partial hemisections of the spinal cord at the first or second cervical segment. Their brains were processed for conventional Nissl staining. The sections were surveyed for the presence or absence of retrograde chromatolysis. Based on analysis and comparison of results from lesions in the various spinal cord funiculi, the following conclusions were reached: The interstitial nucleus projects ipsilaterally to the spinal cord via the medial longitudinal fasciculus, as does the middle reticular field of the metencephalon. The red nucleus and dorsal vagal motor nucleus both project contralaterally to the spinal cord via the dorsal part of the lateral funiculus. The superior reticular field in the rostral metencephalon and the ventrolateral vestibular nucleus project ipsilaterally to the spinal cord via the ventral funiculus. The dorsolateral metencephalic nucleus and the ventral part of the inferior reticular nucleus of the myelencephalon both project ipsilaterally to the spinal cord via the dorsal part of the lateral funiculus. Several brainstem nuclei in Tupinambis project bilaterally to the spinal cord. The ventrolateral metencephalic nucleus, for example, projects ipsilaterally to the cord via the medial longitudinal fasciculus and contralaterally via the dorsal part of the lateral funiculus. The dorsal part of the inferior reticular nucleus projects bilaterally to the spinal cord via the dorsal part of the lateral funiculus. The nucleus solitarius complex projects contralaterally via the dorsal part of the lateral funiculus but ipsilaterally via the middle of the lateral funiculus. The inferior raphe nucleus projects bilaterally to the spinal cord via the middle part of the lateral funiculus. These data suggest that supraspinal projections in reptiles, especially reticulospinal systems, are more highly differentiated than previously thought. On the other hand, recent findings in cat, opossum, and monkey reveal that the organization of supraspinal pathways in the Tegu lizard bears a striking resemblance to that observed in mammals.

Boston Architectural College Urban Sustainability Initiative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byers, Arthur C.

The Boston Architectural College's Urban Sustainability initiative is a demonstration project as defined by the National Energy Technology Laboratory. BAC's proposed project with the U.S. Department of Energy - NETL, is a large part of that overall initiative. The BAC's Urban Sustainability Initiative is a multi-part project with several important goals and objectives that will have a significant impact on the surrounding neighborhood including: energy conservation, reduction of storm water runoff, generation of power through alternative energy sources, elimination/reduction of BAC carbon footprint, and to create a vehicle for ongoing public outreach and education. Education and outreach opportunities will servemore » to add to the already comprehensive Sustainability Design courses offered at BAC relative to energy savings, performance and conservation in building design. At the finish of these essential capital projects there will be technical materials created for the education of the design, sustainability, engineering, community development and historic preservation communities, to inform a new generation of environmentally-minded designers and practitioners, the city of Boston and the general public. The purpose of the initiative, through our green renovations program, is to develop our green alley projects and energy saving renovations to the BAC physical plant, to serve as a working model for energy efficient design in enclosed 19th century and 20th century urban sites and as an educational laboratory for teaching ecological and sustainable technologies to students and the public while creating jobs. The scope of our project as it relates to the BAC and the U.S. Department of Energy- NETL combined efforts includes: Task I of the project is Phase II (Green Alley). Task I encompasses various renovation activities that will demonstrate the effectiveness of permeable paving and ground water recharge systems. It will aid in the reduction of storm water runoff into the Charles River Basin in one of its most significantly polluted sections and, will provide a green renovation mechanism for the redirected storm water of a public alley way. This activity is designed to improve the quality of water recharging the ground water and protecting the vulnerable wood pilings under many of the historic masonry buildings in Boston's Back Bay. Sustainable design research and system monitoring opportunities will also be incorporated, providing ongoing tools for public outreach and education through innovative signage and "virtual tour" technology. The monitoring will include a "building performance dash board" that reflects real time operating conditions and improvements in environmental and economic performance to be prominently displayed on the face of our 320 Newbury Street building (approximately 1.5 million people walk by annually). The project site and demonstration area is located at the rear of 951 Boylston Street, Boston, MA 02115 and the parking area adjacent to Public Alley #444 in Boston's historic Back Bay. Task II of the project is Geothermal Solution. This task involves the installation of approximately seven Geothermal wells which will tap into the earth's constant underground temperatures to provide air-conditioning and heating for BAC facilities. The environmentally friendly geothermal system uses no fossil fuel, produces no emissions and runs silently, providing a sustainable model for commercial and residential buildings throughout Boston. Ultimately the combination of this project and other projects will assist in making the BAC "carbon-neutral", and could generate enough additional energy to provide free power to the Engine 33 and Ladder 15 Firehouse located at 941 Boylston Street. The project is located at the rear of 951 Boylston Street, Boston, MA 02115 and the parking area adjacent to Public Alley #444 in Boston's historic Back Bay. Task III of the project is the Sustainability Design Curriculum at the BAC. The BAC is the nation’s largest independent, multi-disciplinary college of spatial design, and a leader in sustainable design education. The Sustainabiltiy Design program, in particular, focuses on energy efficiency,energy performance, energy modeling, energy and air quality principles, green building, renewable energy alternatives and much more. Additionally, the Urban Sustainability Initiative has an objective of providing courses relative to the BAC's demonstration project with DOE, the project’s period of performance activities, subsequent performance data and anticipated sustainability teaching tools. In keeping with BAC's practice based curriculum, students have been involved in the discussion and planning of this project since its inception and sustainability issues have become a part of other programs throughout the college as well. Students will continue to benefit from this hands-on learning opportunity. The project is located at 320 Newbury Street Boston, MA 02115. Task IV of the project is Program Management and Reporting. This task will involve BAC's oversight and general management of the entire project including subcontract administration, contracts administration, technical and financial reporting, design and renovation assistance, other deliverables in accordance with the Federal Assistance reporting Checklist and other contractual obligations and provisions.« less

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites. Topical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Fifield, Leonard S.; Wang, Jin

2016-06-01

This project aimed to integrate, optimize, and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk® Simulation Moldflow® Insight (ASMI) software package for injection-molded long-carbon-fiber (LCF) thermoplastic composite structures. The project was organized into two phases. Phase 1 demonstrated the ability of the advanced ASMI package to predict fiber orientation and length distributions in LCF/polypropylene (PP) and LCF/polyamide-6, 6 (PA66) plaques within 15% of experimental results. Phase 2 validated the advanced ASMI package by predicting fiber orientation and length distributions within 15% of experimental results for a complex three-dimensional (3D) Toyota automotive part injection-moldedmore » from LCF/PP and LCF/PA66 materials. Work under Phase 2 also included estimate of weight savings and cost impacts for a vehicle system using ASMI and structural analyses of the complex part. The present report summarizes the completion of Phases 1 and 2 work activities and accomplishments achieved by the team comprising Pacific Northwest National Laboratory (PNNL); Purdue University (Purdue); Virginia Polytechnic Institute and State University (Virginia Tech); Autodesk, Inc. (Autodesk); PlastiComp, Inc. (PlastiComp); Toyota Research Institute North America (Toyota); Magna Exteriors and Interiors Corp. (Magna); and University of Illinois. Figure 1 illustrates the technical approach adopted in this project that progressed from compounding LCF/PP and LCF/PA66 materials, to process model improvement and implementation, to molding and modeling LCF/PP and LCF/PA66 plaques. The lessons learned from the plaque study and the successful validation of improved process models for fiber orientation and length distributions for these plaques enabled the project to go to Phase 2 to mold, model, and optimize the 3D complex part.« less

NASA Ames DEVELOP Interns: Helping the Western United States Manage Natural Resources One Project at a Time

NASA Technical Reports Server (NTRS)

Justice, Erin; Newcomer, Michelle

2010-01-01

The western half of the United States is made up of a number of diverse ecosystems ranging from arid desert to coastal wetlands and rugged forests. Every summer for the past 7 years students ranging from high school to graduate level gather at NASA Ames Research Center (ARC) as part of the DEVELOP Internship Program. Under the guidance of Jay Skiles [Ames Research Center (ARC) - Ames DEVELOP Manager] and Cindy Schmidt [ARC/San Jose State University Ames DEVELOP Coordinator] they work as a team on projects exploring topics including: invasive species, carbon flux, wetland restoration, air quality monitoring, storm visualizations, and forest fires. The study areas for these projects have been in Washington, Utah, Oregon, Nevada, Hawaii, Alaska and California. Interns combine data from NASA and partner satellites with models and in situ measurements to complete prototype projects demonstrating how NASA data and resources can help communities tackle their Earth Science related problems.

ANFIS multi criteria decision making for overseas construction projects: a methodology

NASA Astrophysics Data System (ADS)

Utama, W. P.; Chan, A. P. C.; Zulherman; Zahoor, H.; Gao, R.; Jumas, D. Y.

2018-02-01

A critical part when a company targeting a foreign market is how to make a better decision in connection with potential project selection. Since different attributes of information are often incomplete, imprecise and ill-defined in overseas projects selection, the process of decision making by relying on the experiences and intuition is a risky attitude. This paper aims to demonstrate a decision support method in deciding overseas construction projects (OCPs). An Adaptive Neuro-Fuzzy Inference System (ANFIS), the amalgamation of Neural Network and Fuzzy Theory, was used as decision support tool to decide to go or not go on OCPs. Root mean square error (RMSE) and coefficient of correlation (R) were employed to identify the ANFIS system indicating an optimum and efficient result. The optimum result was obtained from ANFIS network with two input membership functions, Gaussian membership function (gaussmf) and hybrid optimization method. The result shows that ANFIS may help the decision-making process for go/not go decision in OCPs.

Global Development of Commercial Underground Coal Gasification

NASA Astrophysics Data System (ADS)

Blinderman, M. S.

2017-07-01

Global development of Underground Coal Gasification (UCG) is considered here in light of latest trends of energy markets and environmental regulations in the countries that have been traditional proponents of UCG. The latest period of UCG development triggered by initial success of the Chinchilla UCG project (1997-2006) has been characterized by preponderance of privately and share-market funded developments. The deceleration of UCG commercialization has been in part caused by recent significant decrease of world oil, gas and coal prices. Another substantial factor was lack of necessary regulations governing extraction and conversion of coal by UCG method in the jurisdictions where the UCG projects were proposed and developed. Along with these objective causes there seem to have been more subjective and technical reasons for a slowdown or cancelation of several significant UCG projects, including low efficiency, poor environmental performance, and inability to demonstrate technology at a sufficient scale and/or at a competitive cost. Latest proposals for UCG projects are briefly reviewed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nester, Patrick

The rooftop Photovoltaic (PV) panels and radiant piping project was constructed by Fort Mason Center as part of its $21 million comprehensive rehabilitation of the Pier 2 shed which include the shed’s electrical, natural gas and water systems. Fort Mason Center improved performance while reducing energy and water usage and costs to demonstrate the efficiencies and opportunities available to large multi-function facilities. The scalable demand of these facilities required a layered approach to conservation, control and production. The project employed a comprehensive retrofit of electrical natural gas, and plumbing systems to maximize efficiency and lower carbon footprint specifically to demonstratemore » the effectiveness of these strategies in a public setting with varied and diverse use. The project was completed in July 2014 and met the expected outcomes regarding increased comfort and operational efficiency throughout the Pier 2 shed as well as on site electrical generation of current consumption. The entire Pier 2 shed project won a 2015 California Preservation Foundation design award for historic rehabilitation.« less

The STARPAHC collection: part of an archive of the history of telemedicine.

PubMed

Freiburger, Gary; Holcomb, Mary; Piper, Dave

2007-01-01

An early telemedicine project involving NASA, the Papago Tribe (now the Tohono O'odham Indian Nation), the Lockheed Missile and Space Company, the Indian Health Service and the Department of Health, Education and Welfare explored the possibilities of using technology to provide improved health care to a remote population in southern Arizona. The project, called STARPAHC (Space Technology Applied to Rural Papago Advanced Health Care), took place in the 1970s and demonstrated the feasibility of a consortium of public and private partners working together to provide medical care to remote populations via telecommunication. In 2001 the Arizona Health Sciences Library acquired important archival materials documenting the STARPAHC project and in collaboration with the Arizona Telemedicine Program established the Arizona Archive of Telemedicine. The material is likely to interest those studying early attempts to use technology to deliver health care at a distance, as well as those studying the sociological ramifications of technical and scientific projects among indigenous populations.

Towards the distribution network of time and frequency

NASA Astrophysics Data System (ADS)

Lipiński, M.; Krehlik, P.; Śliwczyński, Ł.; Buczek, Ł.; Kołodziej, J.; Nawrocki, J.; Nogaś, P.; Dunst, P.; Lemański, D.; Czubla, A.; Pieczerak, J.; Adamowicz, W.; Pawszak, T.; Igalson, J.; Binczewski, A.; Bogacki, W.; Ostapowicz, P.; Stroiński, M.; Turza, K.

2014-05-01

In the paper the genesis, current stage and perspectives of the OPTIME project are described. The main goal of the project is to demonstrate that the newdeveloped at AGH technology of fiber optic transfer of the atomic clocks reference signals is ready to be used in building the domestic Time and Frequency distribution network. In the first part we summarize the two-year continuous operation of 420 kmlong link connecting the Laboratory of Time and Frequency at Central Office of Measures GUM in Warsaw and Time Service Laboratory at Astrogeodynamic Obserwatory AOS in Borowiec near Poznan. For the first time, we are reporting the two year comparison of UTC(PL) and UTC(AOS) atomic timescales with this link, and we refer it to the results of comparisons performed by GPS-based methods. We also address some practical aspects of maintaining time and frequency dissemination over fiber optical network. In the second part of the paper the concept of the general architecture of the distribution network with two Reference Time and Frequency Laboratories and local repositories is proposed. Moreover the brief project of the second branch connecting repositories in Poznan Polish Supercomputing and Networking Center and Torun Nicolaus Copernicus University with the first end-users in Torun such as National Laboratory of Atomic, Molecular and Optical Physics and Nicolaus Copernicus Astronomical Center is described. In the final part the perspective of developing the network both in the domestic range as far as extention with the international connections possibilities are presented.

[The LORAS project and quality assurance. In four years from input- to outcome-oriented financing in public health. 2: LORAS project outcome parts 1 & 98].

PubMed

Lenz, M J; Hochreutener, M A

2001-04-01

This series of three articles is a summary of the operations, findings and results of the hospital reform projects in the Canton of Zurich, termed LORAS. With the aid of the LORAS project within four years Zurich hospitals have been transformed. Whereas they used to adhere to input-oriented covering of deficits they now operate with outcome-oriented prospective financing of output. Part 1 describes the whole project. Part 2 focuses on the development of outcome-measurement. Part 3 finally describes the implementation of the outcome-measurement in the canton of Zurich.

5 CFR 470.303 - Eligible parties.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PERSONNEL MANAGEMENT RESEARCH PROGRAMS AND DEMONSTRATIONS PROJECTS Regulatory Requirements Pertaining to Demonstration Projects § 470.303... demonstration projects under 5 U.S.C. 4701(a)(1) and 4701(b) may conduct demonstration projects after approval...

40 CFR 117.14 - Demonstration projects.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

40 CFR 117.14 - Demonstration projects.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 23 2012-07-01 2012-07-01 false Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

40 CFR 117.14 - Demonstration projects.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 23 2013-07-01 2013-07-01 false Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

40 CFR 117.14 - Demonstration projects.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 22 2014-07-01 2013-07-01 true Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

40 CFR 117.14 - Demonstration projects.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Demonstration projects. 117.14 Section... DETERMINATION OF REPORTABLE QUANTITIES FOR HAZARDOUS SUBSTANCES Applicability § 117.14 Demonstration projects... research or demonstration projects relating to the prevention, control, or abatement of hazardous substance...

Comparing and using assessments of the value of information to clinical decision-making.

PubMed Central

Urquhart, C J; Hepworth, J B

1996-01-01

This paper discusses the Value project, which assessed the value to clinical decision-making of information supplied by National Health Service (NHS) library and information services. The project not only showed how health libraries in the United Kingdom help clinicians in decision-making but also provided quality assurance guidelines for these libraries to help make their information services more effective. The paper reviews methods and results used in previous studies of the value of health libraries, noting that methodological differences appear to affect the results. The paper also discusses aspects of user involvement, categories of clinical decision-making, the value of information to present and future clinical decisions, and the combination of quantitative and qualitative assessments of value, as applied to the Value project and the studies reviewed. The Value project also demonstrated that the value placed on information depends in part on the career stage of the physician. The paper outlines the structure of the quality assurance tool kit, which is based on the findings and methods used in the Value project. PMID:8913550

PREVAIL: IBM's e-beam technology for next generation lithography

NASA Astrophysics Data System (ADS)

Pfeiffer, Hans C.

2000-07-01

PREVAIL - Projection Reduction Exposure with Variable Axis Immersion Lenses represents the high throughput e-beam projection approach to NGL which IBM is pursuing in cooperation with Nikon Corporation as alliance partner. This paper discusses the challenges and accomplishments of the PREVAIL project. The supreme challenge facing all e-beam lithography approaches has been and still is throughput. Since the throughput of e-beam projection systems is severely limited by the available optical field size, the key to success is the ability to overcome this limitation. The PREVAIL technique overcomes field-limiting off-axis aberrations through the use of variable axis lenses, which electronically shift the optical axis simultaneously with the deflected beam so that the beam effectively remains on axis. The resist images obtained with the Proof-of-Concept (POC) system demonstrate that PREVAIL effectively eliminates off- axis aberrations affecting both resolution and placement accuracy of pixels. As part of the POC system a high emittance gun has been developed to provide uniform illumination of the patterned subfield and to fill the large numerical aperture projection optics designed to significantly reduce beam blur caused by Coulomb interaction.

Probabilistic inversion of expert assessments to inform projections about Antarctic ice sheet responses.

PubMed

Fuller, Robert William; Wong, Tony E; Keller, Klaus

2017-01-01

The response of the Antarctic ice sheet (AIS) to changing global temperatures is a key component of sea-level projections. Current projections of the AIS contribution to sea-level changes are deeply uncertain. This deep uncertainty stems, in part, from (i) the inability of current models to fully resolve key processes and scales, (ii) the relatively sparse available data, and (iii) divergent expert assessments. One promising approach to characterizing the deep uncertainty stemming from divergent expert assessments is to combine expert assessments, observations, and simple models by coupling probabilistic inversion and Bayesian inversion. Here, we present a proof-of-concept study that uses probabilistic inversion to fuse a simple AIS model and diverse expert assessments. We demonstrate the ability of probabilistic inversion to infer joint prior probability distributions of model parameters that are consistent with expert assessments. We then confront these inferred expert priors with instrumental and paleoclimatic observational data in a Bayesian inversion. These additional constraints yield tighter hindcasts and projections. We use this approach to quantify how the deep uncertainty surrounding expert assessments affects the joint probability distributions of model parameters and future projections.

AI Techniques for Space: The APSI Approach

NASA Astrophysics Data System (ADS)

Steel, R.; Niézette, M.; Cesta, A.; Verfaille, G., Lavagna, M.; Donati, A.

2009-05-01

This paper will outline the framework and tools developed under the Advanced Planning and Schedule Initiative (APSI) study performed by VEGA for the European Space Agency in collaboration with three academic institutions, ISTC-CNR, ONERA, and Politecnico di Milano. We will start by illustrating the background history to APSI and why it was needed, giving a brief summary of all the partners within the project and the rolls they played within it. We will then take a closer look at what APSI actually consists of, showing the techniques that were used and detailing the framework that was developed within the scope of the project. We will follow this with an elaboration on the three demonstration test scenarios that have been developed as part of the project, illustrating the re-use and synergies between the three cases along the way. We will finally conclude with a summary of some pros and cons of the approach devised during the project and outline future directions to be further investigated and expanded on within the context of the work performed within the project.

Overview of free-piston Stirling technology at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1985-01-01

An overview of the National Aeronautics and Space Administration (NASA) Lewis Research Center (Lewis) free-piston Stirling engine activities is presented. These activities include: (1) a generic free-piston Stirling technology project being conducted to develop technologies synergistic to both space power and terrestrial heat pump applications in a cooperative, cost-shared effort with the Department of Energy (DOE/Oak Ridge National Laboratory (ONRL)), and (2) a free-piston Stirling space-power technology demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), DOE, and NASA/Lewis. The generic technology effort includes extensive parametric testing of a 1 kw free-piston Stirling engine (RE-1000), development and validation of a free-piston Stirling performance computer code, and fabrication and initial testing of an hydraulic output modification for the RE-1000 engine. The space power technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including early test results.

Cryogenics Testbed Laboratory Flange Baseline Configuration

NASA Technical Reports Server (NTRS)

Acuna, Marie Lei Ysabel D.

2013-01-01

As an intern at Kennedy Space Center (KSC), I was involved in research for the Fluids and Propulsion Division of the NASA Engineering (NE) Directorate. I was immersed in the Integrated Ground Operations Demonstration Units (IGODU) project for the majority of my time at KSC, primarily with the Ground Operations Demonstration Unit Liquid Oxygen (GODU L02) branch of IGODU. This project was established to develop advancements in cryogenic systems as a part of KSC's Advanced Exploration Systems (AES) program. The vision of AES is to develop new approaches for human exploration, and operations in and beyond low Earth orbit. Advanced cryogenic systems are crucial to minimize the consumable losses of cryogenic propellants, develop higher performance launch vehicles, and decrease operations cost for future launch programs. During my internship, I conducted a flange torque tracking study that established a baseline configuration for the flanges in the Simulated Propellant Loading System (SPLS) at the KSC Cryogenics Test Laboratory (CTL) - the testing environment for GODU L02.

Standard Biological Parts Knowledgebase

PubMed Central

Galdzicki, Michal; Rodriguez, Cesar; Chandran, Deepak; Sauro, Herbert M.; Gennari, John H.

2011-01-01

We have created the Knowledgebase of Standard Biological Parts (SBPkb) as a publically accessible Semantic Web resource for synthetic biology (sbolstandard.org). The SBPkb allows researchers to query and retrieve standard biological parts for research and use in synthetic biology. Its initial version includes all of the information about parts stored in the Registry of Standard Biological Parts (partsregistry.org). SBPkb transforms this information so that it is computable, using our semantic framework for synthetic biology parts. This framework, known as SBOL-semantic, was built as part of the Synthetic Biology Open Language (SBOL), a project of the Synthetic Biology Data Exchange Group. SBOL-semantic represents commonly used synthetic biology entities, and its purpose is to improve the distribution and exchange of descriptions of biological parts. In this paper, we describe the data, our methods for transformation to SBPkb, and finally, we demonstrate the value of our knowledgebase with a set of sample queries. We use RDF technology and SPARQL queries to retrieve candidate “promoter” parts that are known to be both negatively and positively regulated. This method provides new web based data access to perform searches for parts that are not currently possible. PMID:21390321

Affordable Development and Optimization of CERMET Fuels for NTP Ground Testing

NASA Technical Reports Server (NTRS)

Hickman, Robert R.; Broadway, Jeramie W.; Mireles, Omar R.

2014-01-01

CERMET fuel materials for Nuclear Thermal Propulsion (NTP) are currently being developed at NASA's Marshall Space Flight Center. The work is part of NASA's Advanced Space Exploration Systems Nuclear Cryogenic Propulsion Stage (NCPS) Project. The goal of the FY12-14 project is to address critical NTP technology challenges and programmatic issues to establish confidence in the affordability and viability of an NTP system. A key enabling technology for an NCPS system is the fabrication of a stable high temperature nuclear fuel form. Although much of the technology was demonstrated during previous programs, there are currently no qualified fuel materials or processes. The work at MSFC is focused on developing critical materials and process technologies for manufacturing robust, full-scale CERMET fuels. Prototypical samples are being fabricated and tested in flowing hot hydrogen to understand processing and performance relationships. As part of this initial demonstration task, a final full scale element test will be performed to validate robust designs. The next phase of the project will focus on continued development and optimization of the fuel materials to enable future ground testing. The purpose of this paper is to provide a detailed overview of the CERMET fuel materials development plan. The overall CERMET fuel development path is shown in Figure 2. The activities begin prior to ATP for a ground reactor or engine system test and include materials and process optimization, hot hydrogen screening, material property testing, and irradiation testing. The goal of the development is to increase the maturity of the fuel form and reduce risk. One of the main accomplishmens of the current AES FY12-14 project was to develop dedicated laboratories at MSFC for the fabrication and testing of full length fuel elements. This capability will enable affordable, near term development and optimization of the CERMET fuels for future ground testing. Figure 2 provides a timeline of the development and optimization tasks for the AES FY15-17 follow on program.

75 FR 77379 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-10

... Personnel Management Demonstration Project, Department of Navy, Office of Naval Research; Notice #0;#0..., authorizes the Secretary of Defense (SECDEF) to conduct personnel management demonstration projects at... to execute a process and plan to employ the Department's personnel management demonstration project...

75 FR 30197 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... adopt the Naval Research Laboratory (NRL) Personnel Management Demonstration Project with modifications... Secretary of Defense (SECDEF) to conduct personnel management demonstration projects at DoD laboratories... execute a process and plan to employ the personnel management demonstration project authorities granted to...

76 FR 12080 - TRICARE Access to Care Demonstration Project

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... DEPARTMENT OF DEFENSE Office of the Secretary TRICARE Access to Care Demonstration Project AGENCY..., Section 1092, entitled Department of Defense TRICARE Access to Care Demonstration Project. The demonstration project is intended to improve access to urgent care including minor illness or injury for Coast...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yee, Nathan; Barkay, Tamar; Reinfelder, John

Mercury (Hg) associated with mixed waste generated by nuclear weapons manufacturing has contaminated vast areas of the Oak Ridge Reservation (ORR). Neurotoxic methylmercury (MeHg) has been formed from the inorganic Hg wastes discharged into headwaters of East Fork Poplar Creek (EFPC). Thus, understanding the processes and mechanisms that lead to Hg methylation along the flow path of EFPC is critical to predicting the impacts of the contamination and the design of remedial action at the ORR. In part I of our project, we investigated Hg(0) oxidation and methylation by anaerobic bacteria. We discovered that the anaerobic bacterium Desulfovibrio desulfuricans ND132more » can oxidize elemental mercury [Hg(0)]. When provided with dissolved elemental mercury, D. desulfuricans ND132 converts Hg(0) to Hg(II) and neurotoxic methylmercury [MeHg]. We also demonstrated that diverse species of subsurface bacteria oxidizes dissolved elemental mercury under anoxic conditions. The obligate anaerobic bacterium Geothrix fermentans H5, and the facultative anaerobic bacteria Shewanella oneidensis MR-1 and Cupriavidus metallidurans AE104 can oxidize Hg(0) to Hg(II) under anaerobic conditions. In part II of our project, we established anaerobic enrichment cultures and obtained new bacterial strains from the DOE Oak Ridge site. We isolated three new bacterial strains from subsurface sediments collected from Oak Ridge. These isolates are Bradyrhizobium sp. strain FRC01, Clostridium sp. strain FGH, and a novel Negativicutes strain RU4. Strain RU4 is a completely new genus and species of bacteria. We also demonstrated that syntrophic interactions between fermentative bacteria and sulfate-reducing bacteria in Oak Ridge saprolite mediate iron reduction via multiple mechanisms. Finally, we tested the impact of Hg on denitrification in nitrate reducing enrichment cultures derived from subsurface sediments from the Oak Ridge site, where nitrate is a major contaminant. We showed that there is an inverse relationship between Hg concentrations and rates of denitrification in enrichment cultures. In part III of our project, we examined in more detail the effects of microbial interactions on Hg transformations. We discovered that both sulfate reducing and iron reducing bacteria coexist in freshwater sediments and both microbial groups contribute to mercury methylation. We showed that mercury methylation by sulfate reducing and iron reducing bacteria are temporally and spatially separated processes. We also discovered that methanogens can methylate mercury. We showed that Methanospirillum hungatei JF-1 methylated Hg at comparable rates, but with higher yields, than those observed for sulfate-reducing bacteria and iron-reducing bacteria. Finally, we demonstrated that syntrophic interactions between different microbial groups increase mercury methylation rates. We showed that Hg methylation rates are stimulated via inter-species hydrogen and acetate transfer (i) from sulfate-reducing bacteria to methanogens and (ii) from fermenters to the sulfate-reducing bacteria. In part IV of the project, we studied Hg bioavailability and Hg isotope fractionation. We demonstrated that thiol-bound Hg is bioavailable to mercury resistant bacteria. We found that uptake of Hg from Hg-glutathione and Hg-cysteine complexes does not require functioning glutathione and cystine/cysteine transport systems. We demonstrated that a wide range of methylmercury complexes (e.g. MeHgOH, MeHg-cysteine, and MeHg-glutathione) are bioavailable to mercury resistant bacteria. The rate of MeHg demethylation varies more between different species of mercury resistant bacteria than among MeHg complexes. We showed that microbial demethylation of MeHg depends more on the species of microorganism than on the types and relative concentrations of thiols or other MeHg ligands present. Finally, we demonstrated that Hg methylation by Geobacter sulfurreducens PCA and Desulfovibrio desulfuricans ND132 imparts mass-dependent discrimination against 202Hg relative to 198Hg. G. sulfurreducens PCA and D. desulfuricans ND132 have similar kinetic reactant/product Hg fractionation factors. Using the Hg isotope data, we showed that there are multiple intra- and/or extracellular pools provide substrate inorganic Hg for methylation.« less

LEARNERS: Interdisciplinary Learning Technology Projects Provide Visualizations and Simulations for Use of Geospatial Data in the Classroom

NASA Astrophysics Data System (ADS)

Farrell, N.; Hoban, S.

2001-05-01

The NASA Leading Educators to Applications, Research and NASA-related Educational Resources in Science (LEARNERS) initiative supports seven projects for enhancing kindergarten-to-high school science, geography, technology and mathematics education through Internet-based products derived from content on NASA's mission. Topics incorporated in LEARNERS projects include remote sensing of the Earth for agriculture and weather/climate studies, virtual exploration of remote worlds using robotics and digital imagery. Learners are engaged in inquiry or problem-based learning, often assuming the role of an expert scientist as part of an interdisciplinary science team, to study and explain practical problems using real-time NASA data. The presentation/poster will demonstrate novel uses of remote sensing data for K-12 and Post-Secondary students. This will include the use of visualizations, tools for educators, datasets, and classroom scenarios.

Urban Green Space and the Pursuit of Health Equity in Parts of the United States.

PubMed

Jennings, Viniece; Baptiste, April Karen; Osborne Jelks, Na'Taki; Skeete, Renée

2017-11-22

Research has demonstrated that inequitable access to green space can relate to health disparities or inequalities. This commentary aims to shift the dialogue to initiatives that have integrated green spaces in projects that may promote health equity in the United States. Specifically, we connect this topic to factors such as community revitalization, affordable housing, neighborhood walkability, food security, job creation, and youth engagement. We provide a synopsis of locations and initiatives in different phases of development along with characteristics to support effectiveness and strategies to overcome challenges. The projects cover locations such as Atlanta (GA), Los Angeles (CA), the District of Columbia (Washington D.C.), South Bronx (NY), and Utica (NY). Such insight can develop our understanding of green space projects that support health equity and inform the dialogue on this topic in ways that advance research and advocacy.

Urban Green Space and the Pursuit of Health Equity in Parts of the United States

PubMed Central

Jennings, Viniece; Baptiste, April Karen; Osborne Jelks, Na’Taki; Skeete, Renée

2017-01-01

Research has demonstrated that inequitable access to green space can relate to health disparities or inequalities. This commentary aims to shift the dialogue to initiatives that have integrated green spaces in projects that may promote health equity in the United States. Specifically, we connect this topic to factors such as community revitalization, affordable housing, neighborhood walkability, food security, job creation, and youth engagement. We provide a synopsis of locations and initiatives in different phases of development along with characteristics to support effectiveness and strategies to overcome challenges. The projects cover locations such as Atlanta (GA), Los Angeles (CA), the District of Columbia (Washington D.C.), South Bronx (NY), and Utica (NY). Such insight can develop our understanding of green space projects that support health equity and inform the dialogue on this topic in ways that advance research and advocacy. PMID:29165367

Department of Homeland Security Summer Internship

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, Erika J.

2010-07-30

My time at Lawrence Livermore National Laboratory (LLNL) has been one of the most rewarding and exciting experiences of my life. When I first applied for a Department of Homeland Security (DHS) internship I was concerned that my major in Mass Communications and Emergency Management would not be suited for the hard science environment. Thankfully DHS and my mentor, Brooke Buddemeier, demonstrated that the skills and knowledge I possess are critical for the successful integration of good science into Homeland Security and emergency response, and allowed me the opportunity to work on an exciting project. This paper intends to givemore » an overview of my experiences while at LLNL, explain the project I have been a part of, explain my specific role within that project, discuss my achievements, explain how my internship has changed where I plan to take my career path, and, finally, discuss how I believe DHS can enhance their future internship programs.« less

GLIMPSE: An integrated assessment model-based tool for ...

EPA Pesticide Factsheets

Dan Loughlin will describe the GCAM-USA integrated assessment model and how that model is being improved and integrated into the GLIMPSE decision support system. He will also demonstrate the application of the model to evaluate the emissions and health implications of hypothetical state-level renewable electricity standards. Introduce the GLIMPSE project to state and regional environmental modelers and analysts. Presented as part of the State Energy and Air Quality Group Webinar Series, which is organized by NESCAUM.

Flying the ST-5 Constellation with "Plug and Play" Autonomy Components and the GMSEC Bus

NASA Technical Reports Server (NTRS)

Shendock, Bob; Witt, Ken; Stanley, Jason; Mandl, Dan; Coyle, Steve

2006-01-01

The Space Technology 5 (ST5) Project, part of NASA's New Millennium Program, will consist of a constellation of three micro-satellites. This viewgraph document presents the components that will allow it to operate in an autonomous mode. The ST-5 constellation will use the GSFC Mission Services Evolution Center (GMSEC) architecture to enable cost effective model based operations. The ST-5 mission will demonstrate several principles of self managing software components.

Microbial Monitoring from the Frontlines to Space: A Successful Validation of a Department of Defense (DoD) Funded Small Business Innovation Research (SBIR) Technology on Board the International Space Station (ISS)

NASA Technical Reports Server (NTRS)

Oubre, Cherie; Khodadad, Christina; Castro, Victoria; Ott, Mark; Pollack, Lawrence; Roman, Monsi

2017-01-01

The RAZOR EX (Registered Trademark) PCR unit was initially developed by the DoD as part of an SBIR project to detect and identify biothreats during field deployment. The system was evaluated by NASA as a commercial technology for future microbial monitoring requirements and has been successfully demonstrated in microgravity on-board the International Space Station.

77 FR 21102 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-09

... OMB Review; Comment Request Title: Child Welfare Demonstration Projects Information Collection. OMB No... child welfare waiver demonstration projects. CB is able to approve up to ten child welfare waiver demonstration projects in each of Fiscal Years 2012, 2013 and 2014. These waiver demonstration projects involve...

77 FR 69601 - Science and Technology Reinvention Laboratory (STRL) Personnel Management Demonstration Projects

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-20

...) Personnel Management Demonstration Projects AGENCY: Office of the Deputy Assistant Secretary of Defense... to demonstration project plans. SUMMARY: Section 342(b) of the National Defense Authorization Act... the NDAA for FY 2001, authorizes the Secretary of Defense to conduct personnel demonstration projects...

75 FR 27865 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... of coverage of the AFRL Personnel Demonstration Project to AFRL employees in Business Management and... conduct demonstration projects to determine whether a specified change in personnel management policies or... plan to employ the personnel management demonstration project authorities granted to the Office of...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nikolov, Nikolay; Sainsbury-Martinez, Felix, E-mail: nikolay@astro.ex.ac.uk

Planetary rotation rates and obliquities provide information regarding the history of planet formation, but have not yet been measured for evolved extrasolar planets. Here we investigate the theoretical and observational perspective of the Rossiter–McLaughlin effect during secondary eclipse (RMse) ingress and egress for transiting exoplanets. Near secondary eclipse, when the planet passes behind the parent star, the star sequentially obscures light from the approaching and receding parts of the rotating planetary surface. The temporal block of light emerging from the approaching (blueshifted) or receding (redshifted) parts of the planet causes a temporal distortion in the planet’s spectral line profiles resultingmore » in an anomaly in the planet’s radial velocity curve. We demonstrate that the shape and the ratio of the ingress-to-egress radial velocity amplitudes depends on the planetary rotational rate, axial tilt, and impact factor (i.e., sky-projected planet spin–orbital alignment). In addition, line asymmetries originating from different layers in the atmosphere of the planet could provide information regarding zonal atmospheric winds and constraints on the hot spot shape for giant irradiated exoplanets. The effect is expected to be most-pronounced at near-infrared wavelengths, where the planet-to-star contrasts are large. We create synthetic near-infrared, high-dispersion spectroscopic data and demonstrate how the sky-projected spin axis orientation and equatorial velocity of the planet can be estimated. We conclude that the RMse effect could be a powerful method to measure exoplanet spins.« less

Community-based participatory research projects and policy engagement to protect environmental health on St Lawrence Island, Alaska.

PubMed

Miller, Pamela K; Waghiyi, Viola; Welfinger-Smith, Gretchen; Byrne, Samuel Carter; Kava, Jane; Gologergen, Jesse; Eckstein, Lorraine; Scrudato, Ronald; Chiarenzelli, Jeff; Carpenter, David O; Seguinot-Medina, Samarys

2013-01-01

This article synthesizes discussion of collaborative research results, interventions and policy engagement for St Lawrence Island (SLI), Alaska, during the years 2000-2012. As part of on-going community-based participatory research (CBPR) studies on SLI, 5 discrete exposure-assessment projects were conducted: (a) a biomonitoring study of human blood serum; (b-d) 3 investigations of levels of contaminants in environmental media at an abandoned military site at Northeast Cape--using sediment cores and plants, semi-permeable membrane devices and blackfish, respectively; and (e) a study of traditional foods. Blood serum in residents of SLI showed elevated levels of polychlorinated biphenyls (PCBs) with higher levels among those exposed to the military site at Northeast Cape, an important traditional subsistence-use area. Environmental studies at the military site demonstrated that the site is a continuing source of PCBs to a major watershed, and that clean-up operations at the military site generated PCB-contaminated dust on plants in the region. Important traditional foods eaten by the people of SLI showed elevated concentrations of PCBs, which are primarily derived from the long-range transport of persistent pollutants that are transported by atmospheric and marine currents from more southerly latitudes to the north. An important task for all CBPR projects is to conduct intervention strategies as needed in response to research results. Because of the findings of the CBPR projects on SLI, the CBPR team and the people of the Island are actively engaging in interventions to ensure cleanup of the formerly used military sites; reform chemicals policy on a national level; and eliminate persistent pollutants internationally. The goal is to make the Island and other northern/Arctic communities safe for themselves and future generations. As part of the CBPR projects conducted from 2000 to 2012, a series of exposure assessments demonstrate that the leaders of SLI have reason to be concerned about the health of people due to the presence of carcinogenic chemicals as measured in biomonitoring and environmental samples and important traditional foods.

Community-based participatory research projects and policy engagement to protect environmental health on St Lawrence Island, Alaska

PubMed Central

Miller, Pamela K.; Waghiyi, Viola; Welfinger-Smith, Gretchen; Byrne, Samuel Carter; Kava, Jane; Gologergen, Jesse; Eckstein, Lorraine; Scrudato, Ronald; Chiarenzelli, Jeff; Carpenter, David O.; Seguinot-Medina, Samarys

2013-01-01

Objectives This article synthesizes discussion of collaborative research results, interventions and policy engagement for St Lawrence Island (SLI), Alaska, during the years 2000–2012. Methods As part of on-going community-based participatory research (CBPR) studies on SLI, 5 discrete exposure-assessment projects were conducted: (a) a biomonitoring study of human blood serum; (b–d) 3 investigations of levels of contaminants in environmental media at an abandoned military site at Northeast Cape – using sediment cores and plants, semi-permeable membrane devices and blackfish, respectively; and (e) a study of traditional foods. Results Blood serum in residents of SLI showed elevated levels of polychlorinated biphenyls (PCBs) with higher levels among those exposed to the military site at Northeast Cape, an important traditional subsistence-use area. Environmental studies at the military site demonstrated that the site is a continuing source of PCBs to a major watershed, and that clean-up operations at the military site generated PCB-contaminated dust on plants in the region. Important traditional foods eaten by the people of SLI showed elevated concentrations of PCBs, which are primarily derived from the long-range transport of persistent pollutants that are transported by atmospheric and marine currents from more southerly latitudes to the north. Interventions An important task for all CBPR projects is to conduct intervention strategies as needed in response to research results. Because of the findings of the CBPR projects on SLI, the CBPR team and the people of the Island are actively engaging in interventions to ensure cleanup of the formerly used military sites; reform chemicals policy on a national level; and eliminate persistent pollutants internationally. The goal is to make the Island and other northern/Arctic communities safe for themselves and future generations. Conclusions As part of the CBPR projects conducted from 2000 to 2012, a series of exposure assessments demonstrate that the leaders of SLI have reason to be concerned about the health of people due to the presence of carcinogenic chemicals as measured in biomonitoring and environmental samples and important traditional foods. PMID:23977641

18 CFR 16.19 - Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of...

Code of Federal Regulations, 2010 CFR

2010-04-01

... existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power....19 Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power project with a license not subject to sections 14 and 15 of the Federal Power Act. (a...

18 CFR 16.19 - Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of...

Code of Federal Regulations, 2014 CFR

2014-04-01

... existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power....19 Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power project with a license not subject to sections 14 and 15 of the Federal Power Act. (a...

18 CFR 16.19 - Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of...

Code of Federal Regulations, 2013 CFR

2013-04-01

... existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power....19 Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power project with a license not subject to sections 14 and 15 of the Federal Power Act. (a...

18 CFR 16.19 - Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of...

Code of Federal Regulations, 2012 CFR

2012-04-01

... existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power....19 Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power project with a license not subject to sections 14 and 15 of the Federal Power Act. (a...

18 CFR 16.19 - Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of...

Code of Federal Regulations, 2011 CFR

2011-04-01

... existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power....19 Procedures for an existing licensee of a minor hydroelectric power project or of a minor part of a hydroelectric power project with a license not subject to sections 14 and 15 of the Federal Power Act. (a...

Feasibility of using a pediatric call center as part of a quality improvement effort to prevent hospital readmission.

PubMed

Kirsch, Sallie Davis; Wilson, Lauren S; Harkins, Michelle; Albin, Dawn; Del Beccaro, Mark A

2015-01-01

The primary aim of this intervention was to assess the feasibility of using call center nurses who are experts in telephone triage to conduct post discharge telephone calls, as part of a quality improvement effort to prevent hospital readmission. Families of patients with bronchiolitis were called between 24 and 48 hours after discharge. The calls conducted by the nurses were efficient (average time was 12 minutes), and their assessments helped to identify gaps in inpatient family education. Overall, the project demonstrated the efficacy in readmission prevention by using nurses who staff a call center to conduct post-hospitalization telephone calls. Copyright © 2015 Elsevier Inc. All rights reserved.

An electromagnetic induction method for underground target detection and characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartel, L.C.; Cress, D.H.

1997-01-01

An improved capability for subsurface structure detection is needed to support military and nonproliferation requirements for inspection and for surveillance of activities of threatening nations. As part of the DOE/NN-20 program to apply geophysical methods to detect and characterize underground facilities, Sandia National Laboratories (SNL) initiated an electromagnetic induction (EMI) project to evaluate low frequency electromagnetic (EM) techniques for subsurface structure detection. Low frequency, in this case, extended from kilohertz to hundreds of kilohertz. An EMI survey procedure had already been developed for borehole imaging of coal seams and had successfully been applied in a surface mode to detect amore » drug smuggling tunnel. The SNL project has focused on building upon the success of that procedure and applying it to surface and low altitude airborne platforms. Part of SNL`s work has focused on improving that technology through improved hardware and data processing. The improved hardware development has been performed utilizing Laboratory Directed Research and Development (LDRD) funding. In addition, SNL`s effort focused on: (1) improvements in modeling of the basic geophysics of the illuminating electromagnetic field and its coupling to the underground target (partially funded using LDRD funds) and (2) development of techniques for phase-based and multi-frequency processing and spatial processing to support subsurface target detection and characterization. The products of this project are: (1) an evaluation of an improved EM gradiometer, (2) an improved gradiometer concept for possible future development, (3) an improved modeling capability, (4) demonstration of an EM wave migration method for target recognition, and a demonstration that the technology is capable of detecting targets to depths exceeding 25 meters.« less

Erfolgsfaktoren von Lehrstellenmarketing in der dualen berufsbildung: das beispiel Schweiz

NASA Astrophysics Data System (ADS)

Sager, Fritz

2006-09-01

SUCCESS FACTORS OF APPRENTICESHIP MARKETING IN A SYSTEM OF DUAL VOCATIONAL TRAINING: THE CASE OF SWITZERLAND - The dual system of vocational training, utilizing both company training and vocational school, is generally acknowledged to be a successful model, but a decreasing number of trainee posts in Switzerland poses a crisis for the approach. One strategy for overcoming the problem involves offering incentives for companies to create new trainee posts. The present study explores the necessary conditions for successfully influencing the number of trainee posts through apprenticeship marketing. A comparision of qualitative case studies of six marketing projects demonstrates that while context, in the sense of basic structural conditions and political sensibility for the problematic, plays a role in the success of a project, what is central is above all the form of the trainee-post marketing project itself. This has to do with the behaviour of the actors involved as well as the choice of the mode of governance and project organization. The latter has to do with making available requisite technical and personal resources, coordination on the part of the project direction, and giving those responsible the necessary room to act in implementing the project.

78 FR 29335 - Science and Technology Reinvention Laboratory (STRL) Personnel Management Demonstration Projects

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-20

...) Personnel Management Demonstration Projects AGENCY: Office of the Deputy Assistant Secretary of Defense... demonstration project plans. SUMMARY: Section 342(b) of the National Defense Authorization Act (NDAA) for Fiscal... 2001, authorizes the Secretary of Defense to conduct personnel demonstration projects at DoD...

Against the integrative turn in bioethics: burdens of understanding.

PubMed

Savić, Lovro; Ivanković, Viktor

2018-06-01

The advocates of Integrative Bioethics have insisted that this recently emerging project aspires to become a new stage of bioethical development, surpassing both biomedically oriented bioethics and global bioethics. We claim in this paper that if the project wants to successfully replace the two existing paradigms, it at least needs to properly address and surmount the lack of common moral vocabulary problem. This problem points to a semantic incommensurability due to cross-language communication in moral terms. This paper proceeds as follows. In the first part, we provide an overview of Integrative Bioethics and its conceptual building blocks: mutlidisciplinarity, interdisciplinarity, and transdisciplinarity. In the second part, we disclose the problem of semantic incommensurability. The third part gives an overview of various positions on the understanding of interdisciplinarity and integration in interdisciplinary communication, and corresponding attempts at solving the lack of common moral vocabulary problem. Here we lean mostly on Holbrook's three theses regarding the character of interdisciplinary communication. Finally, in the fourth part, we discuss a particular bioethical case-that of euthanasia-to demonstrate the challenge semantic incommensurability poses to dialogues in Integrative Bioethics. We conclude that Integrative Bioethics does not offer a methodological toolset that would warrant optimism in its advocates' predictions of surpassing current modes of doing bioethics. Since Integrative Bioethics leaves controversial methodological questions unresolved on almost all counts and shows no attempts at overcoming the critical stumbling points, we argue for its rejection.

A demonstration device for cosmic rays telescopes

NASA Astrophysics Data System (ADS)

Esposito, Salvatore

2018-01-01

We describe a hands-on accurate demonstrator for cosmic rays realized by six high school students. The main aim is to show the relevance and the functioning of the principal parts of a cosmic ray telescope (muon detector), with the help of two large sized wooden artefacts. The first one points out how cosmic rays can be tracked in a muon telescope, while the other one shows the key avalanche process of electronic ionization that effectively allows muon detection through a photomultiplier. Incoming cosmic rays are visualized in terms of laser beams, whose 3D trajectory is highlighted by turning on LEDs on two orthogonal matrices. Instead the avalanche ionization process is demonstrated through the avalanche falling off glass marbles on an inclined plane, finally turning on a LED. A pictured poster accompanying the demonstrator is as effective in assisting cosmic ray demonstration and its detection. The success of the demonstrator has been fully proven by the general public during a science festival, in which the corresponding project won the Honorable Mention in a dedicated competition.

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defennse (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

LDRD Report: Topological Design Optimization of Convolutes in Next Generation Pulsed Power Devices.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cyr, Eric C.; von Winckel, Gregory John; Kouri, Drew Philip

This LDRD project was developed around the ambitious goal of applying PDE-constrained opti- mization approaches to design Z-machine components whose performance is governed by elec- tromagnetic and plasma models. This report documents the results of this LDRD project. Our differentiating approach was to use topology optimization methods developed for structural design and extend them for application to electromagnetic systems pertinent to the Z-machine. To achieve this objective a suite of optimization algorithms were implemented in the ROL library part of the Trilinos framework. These methods were applied to standalone demonstration problems and the Drekar multi-physics research application. Out of thismore » exploration a new augmented Lagrangian approach to structural design problems was developed. We demonstrate that this approach has favorable mesh-independent performance. Both the final design and the algorithmic performance were independent of the size of the mesh. In addition, topology optimization formulations for the design of conducting networks were developed and demonstrated. Of note, this formulation was used to develop a design for the inner magnetically insulated transmission line on the Z-machine. The resulting electromagnetic device is compared with theoretically postulated designs.« less

Overview of the 1986 free-piston Stirling SP-100 activities at the NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1986-01-01

An overview of the NASA Lewis Research Center SP-100 free-piston Stirling engine activities is presented. These activities include a free-piston Stirling space-power technology feasibility demonstration project as part of the SP-100 program being conducted in support of the Department of Defense (DOD), Department of Energy (DOE), and NASA. The space-power Stirling advanced technology effort, under SP-100, addresses the status of the 25 kWe Space Power Demonstrator Engine (SPDE) including test results. Future space-power projections are presented along with a description of a study that will investigate the feasibility of scaling a single-cylinder free-piston Stirling space-power module to the 150 kW power range. Design parameters and conceptual design features will be presented for a 25 kWe, single-cylinder free-piston Stirling space-power converter. A description of a hydrodynamic gas bearing concept is presented whereby the displacer of a 1 kWe free-piston Stirling engine is modified to demonstrate the bearing concept. And finally the goals of a conceptual design for a 25 kWe Solar Advanced Stirling Conversion System capable of delivering electric power to an electric utility grid are discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutwack, R.

The goal of the Silicon Material Task, a part of the FSA Project, was to develop and demonstrate the technology for the low-cost production of silicon of suitable purity to be used as the basic material for the manufacture of terrestrial photovoltaic solar cells. To be compatible with the price goals of the FSA Project, the price of the produced silicon was to be less than $10/kg (in 1975 dollars). Summarized in this document are 11 different processes for the production of silicon that were investigated and developed to varying extent by industrial, university, and government researchers. The silane-production sectionmore » of the Union Carbide Corp. (UCC) silane process was developed completely in this program. Coupled with Siemens-type chemical vapor deposition reactors, the process was carried through the pilot plant stage. The overall UCC process involves the conversion of metallurgical-grade silicon to silane followed by decomposition of the silane to purified silicon. Production of very high-purity silane and silicon was demonstrated. Although it has as yet not achieved commercial application, the development of fluidized-bed technology for the low-cost, high-throughput conversion of silane-to-silicon has been demonstrated in the research laboratory and now is in engineering development.« less

Schaben field, Kansas: Improving performance in a Mississippian shallow-shelf carbonate

USGS Publications Warehouse

Montgomery, S.L.; Franseen, E.K.; Bhattacharya, S.; Gerlach, P.; Byrnes, A.; Guy, W.; Carr, T.R.

2000-01-01

Schaben field (Kansas), located along the northeastern shelf of the Hugoton embayment, produces from Mississippian carbonates in erosional highs immediately beneath a regional unconformity. Production comes from depths of around 4400 ft (1342 m) in partially dolomitized shelf deposits. A detailed reservoir characterization/simulation study, recently performed as part of a Department of Energy Reservoir Class Oil Field Demonstration Project, has led to important revision in explanations for observed patterns of production. Cores recovered from three new data wells identify three main facies: Spicule-rich wackestone-packstone, echinoderm wackestone/packstone/grainstone, and dolomitic mudstone-wackestone. Reservoir quality is highest in spicule-rich wackestone/packstones but is subject to a very high degree of vertical heterogeneity due to facies interbedding, silification, and variable natural fracturing. The oil reservoir is underlain by an active aquifer, which helps maintain reservoir pressure but supports significant water production. Reservoir simulation, using public-domain, PC-based software, suggests that infill drilling is an efficient approach to enhanced recovery. Recent drilling directed by simulation results has shown considerable success in improving field production rates. Results from the Schaben field demonstration project are likely to have wide application for independent oil and exploration companies in western Kansas.Schaben field (Kansas), located along the northeastern shelf of the Hugoton embayment, produces from Mississippian carbonates in erosional highs immediately beneath a regional unconformity. Production comes from depths of around 4400 ft (1342 m) in partially dolomitized shelf deposits. A detailed reservoir characterization/simulation study, recently performed as part of a Department of Energy Reservoir Class Oil Field Demonstration Project, has led to important revision in explanations for observed patterns of production. Cores recovered from three new data wells identify three main facies: spicule-rich wackestone-packstone, echinoderm wackestone/packstone/grainstone, and dolomitic mudstone-wackestone. Reservoir quality is highest in spicule-rich wackestone/packstones but is subject to a very high degree of vertical heterogeneity due to facies interbedding, silification, and variable natural fracturing. The oil reservoir is underlain by an active aquifer, which helps maintain reservoir pressure but supports significant water production. Reservoir simulation, using public-domain, PC-based software, suggests that infill drilling is an efficient approach to enhanced recovery. Recent drilling directed by simulation results has shown considerable success in improving field production rates. Results from the Schaben field demonstration project are likely to have wide application for independent oil and exploration companies in western Kansas.

Service and Methods Demonstration - Annual Report

DOT National Transportation Integrated Search

1975-11-01

This report contains a description of the Service and Methods Demonstration Program. Transit demonstration projects undertaken in previous years are reviewed. Recently completed and current demonstration projects are described and project results fro...

Organization of cerebellar and area "y" projections to the nucleus reticularis tegmenti pontis in macaque monkeys.

PubMed

Stanton, G B

2001-04-02

Axonal projections to the nucleus reticularis tegmenti pontis (RTP) were studied in 11 macaque monkeys by mapping axonal degeneration from lesions centered in the dentate and interpositus anterior (IA) nuclei and by mapping anterograde transport of tritiated amino acid precursors injected into the dentate nucleus. Projections from the dentate and IA nuclei overlap in central parts of the body of RTP, but the terminal field of dentate axons extends dorsomedial and rostral to the terminal field of IA axons, and IA terminal fields extend more ventrolaterally. A caudal to rostral topography of projections from each nucleus onto dorsal to ventral parts of RTP was seen. Projections from rostral parts of both nuclei terminate in a sublemniscal part of the nucleus. The topography of dentate and IA projections onto central to ventrolateral RTP appears to match somatotopic maps of these cerebellar nuclei with the somatotopic map of projections to RTP from primary motor cortex. Projections from caudal and ventral parts of the dentate nucleus appear to overlap oculomotor inputs to rostral, dorsal, and medial RTP from the frontal and supplementary eye fields, the superior colliculus, and the oculomotor region of the caudal fastigial nucleus. Projections to the paramedian part of RTP from vestibular area "y" were also found in two cases that correlated with projections to vertical oculomotor motoneurons. The maps of dentate and IA projections onto RTP correlate predictably with maps of dentate and IA projections to the ventrolateral thalamus and subnuclei of the red nucleus that were made from these same cases (Stanton [1980b] J. Comp. Neurol. 192:377-385). Copyright 2001 Wiley-Liss, Inc.

Project-Based Learning around the World, Part 2

ERIC Educational Resources Information Center

Weatherby, Kristen

2007-01-01

In part 1 of this article, the author introduced Microsoft's worldwide K-12 education initiative, Partners in Learning, and discusses the partnership with ISTE in creating project-based learning curriculum as part of Partners in Learning. The project-based learning curriculum can be adapted for classrooms across the globe. This paper, the second…

1973-1974 E.S.E.A. Title I Evaluation Report.

ERIC Educational Resources Information Center

Saint Louis Board of Education, MO.

This Illinois District 189, East St. Louis Public Schools, 1973-1974 evaluation report on programs, services, activities and projects funded in whole or in part under Title I of the 1965 Elementary Secondary Education Act is organized into five parts. Part One, 'Title I Projects' comprises reports on seven projects. Continuing Education for…

Improving stamping simulation accuracy by accounting for realistic friction and lubrication conditions: Application to the door-outer of the Mercedes-Benz C-class Coupé

NASA Astrophysics Data System (ADS)

Hol, J.; Wiebenga, J. H.; Stock, J.; Wied, J.; Wiegand, K.; Carleer, B.

2016-08-01

In the stamping of automotive parts, friction and lubrication play a key role in achieving high quality products. In the development process of new automotive parts, it is therefore crucial to accurately account for these effects in sheet metal forming simulations. Only then, one can obtain reliable and realistic simulation results that correspond to the actual try-out and mass production conditions. In this work, the TriboForm software is used to accurately account for tribology-, friction-, and lubrication conditions in stamping simulations. The enhanced stamping simulations are applied and validated for the door-outer of the Mercedes- Benz C-Class Coupe. The project results demonstrate the improved prediction accuracy of stamping simulations with respect to both part quality and actual stamping process conditions.

Mechanical Prototyping and Manufacturing Internship

NASA Technical Reports Server (NTRS)

Grenfell, Peter

2016-01-01

The internship was located at the Johnson Space Center (JSC) Innovation Design Center (IDC), which is a facility where the JSC workforce can meet and conduct hands-on innovative design, fabrication, evaluation, and testing of ideas and concepts relevant to NASA's mission. The tasks of the internship included mechanical prototyping design and manufacturing projects in service of research and development as well as assisting the users of the IDC in completing their manufacturing projects. The first project was to manufacture hatch mechanisms for a team in the Systems Engineering and Project Advancement Program (SETMAP) hexacopter competition. These mechanisms were intended to improve the performance of the servomotors and offer an access point that would also seal to prevent cross-contamination. I also assisted other teams as they were constructing and modifying their hexacopters. The success of this competition demonstrated a proof of concept for aerial reconnaissance and sample return to be potentially used in future NASA missions. I also worked with Dr. Kumar Krishen to prototype an improved thermos and a novel, portable solar array. Computer-aided design (CAD) software was used to model the parts for both of these projects. Then, 3D printing as well as conventional techniques were used to produce the parts. These prototypes were then subjected to trials to determine the success of the designs. The solar array is intended to work in a cluster that is easy to set up and take down and doesn't require powered servomechanisms. It could be used terrestrially in areas not serviced by power grids. Both projects improve planetary exploration capabilities to future astronauts. Other projects included manufacturing custom rail brackets for EG-2, assisting engineers working on underwater instrument and tool cases for the NEEMO project, and helping to create mock-up parts for Space Center Houston. The use of the IDC enabled efficient completion of these projects at significantly reduced cost. I acquired and improved manufacturing and prototyping skills during my tour including learning about a CAD (Computer-Aided Design) program called Creo (Creo Parametric; design software), gaining valuable conventional machining experience with lathes, CNC (Computer Numerical Control) milling machines and various other tools, and improving my engineering project communication and collaboration skills. The internship also allowed me to better understand operations at NASA. I plan to work in the aerospace industry or do academic research benefitting space science and exploration, and this internship experience will enable me to have insight into manufacturing processes for research and development.

DOE Office of Scientific and Technical Information (OSTI.GOV)

French, Troy

Le Norman Energy Company conducted research on field application of alkaline-surfactant-polymer (ASP) flooding as a part of the U.S. Department of Energy's plan to maximize the production of our domestic oil resources. In addition to having substantial technical merit, the process uses chemicals that are environmentally acceptable. Le Norman's field project is located in the Sho-Vel-Tum (OK) oil field, which was a major producer of crude oil in past years, but has since been extensively waterflooded. This reservoir in this portion of the field is typical of many shallow reservoirs in the Oklahoma-Kansas area and is a good demonstration sitemore » for that area. The pay zones are located approximately 700 ft. deep, and this project is the shallowest field test for ASP flooding.« less

Biologically Inspired Micro-Flight Research

NASA Technical Reports Server (NTRS)

Raney, David L.; Waszak, Martin R.

2003-01-01

Natural fliers demonstrate a diverse array of flight capabilities, many of which are poorly understood. NASA has established a research project to explore and exploit flight technologies inspired by biological systems. One part of this project focuses on dynamic modeling and control of micro aerial vehicles that incorporate flexible wing structures inspired by natural fliers such as insects, hummingbirds and bats. With a vast number of potential civil and military applications, micro aerial vehicles represent an emerging sector of the aerospace market. This paper describes an ongoing research activity in which mechanization and control concepts for biologically inspired micro aerial vehicles are being explored. Research activities focusing on a flexible fixed- wing micro aerial vehicle design and a flapping-based micro aerial vehicle concept are presented.

The goldstone energy project

NASA Technical Reports Server (NTRS)

Bartos, K. P.

1978-01-01

The Golstone Energy Project was established in 1974 to investigate ways in which the Goldstone Deep Space Complex in California could be made partly or completely energy-sufficient, especially through the use of solar- and wind-derived energy resources. Ways in which energy could be conserved at the Complex were also studied. Findings included data on both wind and solar energy. Obstacles to demonstrating energy self-sufficiency are: (1) operation and maintenance costs of solar energy systems are estimated to be much higher than conventional energy systems, (2) initial capital costs of present-day technology solar collectors are high and are compounded by low collector efficiency, and (3) no significant market force exists to create the necessary industry to reduce costs through mass production and broad open-market competition.

NASA's F-15B Research Testbed aircraft flies in the supersonic shock wave of a U.S. Navy F-5E as par

NASA Technical Reports Server (NTRS)

2002-01-01

NASA's F-15B Research Testbed aircraft recently flew in the supersonic shock wave of a U.S. Navy F-5E in support of the F-5 Shaped Sonic Boom Demonstration (SSBD) project, part of the Defense Advanced Research Projects Agency's (DARPA) Quiet Supersonic Platform (QSP) program. The flights originated from the NASA Dryden Flight Research Center at Edwards, California. Four flights were flown in order to measure the F-5E's near-field (close-up) sonic boom signature at Mach 1.4, during which more than 50 shockwave patterns were measured at distances as close as 100 feet below the F-5E.

Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Love, Lonnie J.

This Oak Ridge National Laboratory (ORNL) Manufacturing Development Facility (MDF) technical collaboration project was conducted in two phases as a CRADA with Local Motors Inc. Phase 1 was previously reported as Advanced Manufacturing of Complex Cyber Mechanical Devices through Community Engagement and Micro-manufacturing and demonstrated the integration of components onto a prototype body part for a vehicle. Phase 2 was reported as Utility of Big Area Additive Manufacturing (BAAM) for the Rapid Manufacture of Customized Electric Vehicles and demonstrated the high profile live printing of an all-electric vehicle using ONRL s Big Area Additive Manufacturing (BAAM) technology. This demonstration generatedmore » considerable national attention and successfully demonstrated the capabilities of the BAAM system as developed by ORNL and Cincinnati, Inc. and the feasibility of additive manufacturing of a full scale electric vehicle as envisioned by the CRADA partner Local Motors, Inc.« less

Design and development of experimental facilities for short duration, low-gravity combustion and fire experiments

NASA Technical Reports Server (NTRS)

Motevalli, Vahid

1994-01-01

This report contains the results of three projects conducted by undergraduate students from Worcester Polytechnic Institute at the NASA's Lewis Research Center under a NASA Award NCC3-312. The students involved in these projects spent part of the summer of 1993 at the Lewis Research Center (LeRC) under the direction of Dr. Howard Ross, head of the Combustion group and other NASA engineers and scientists. The Principal Investigator at Worcester Polytechnic Institute was Professor Vahid Motevalli. Professor Motevalli served as the principal project advisor for two of the three projects which were in Mechanical Engineering. The third project was advised by Professor Duckworth of Electrical and Computer Engineering, while Professor Motevalli acted as the co-advisor. These projects provided an excellent opportunity for the students to participate in the cutting edge research and engineering design, interact with NASA engineers and gain valuable exposure to a real working environment. Furthermore, the combustion group at LeRC was able to forward their goals by employing students to work on topics of immediate use and interest such as experimental research projects planned for the space shuttle, the future space station, or to develop demonstration tools to educate the public about LeRC activities.

The New Millennium Program Space Technology 5 (ST-5) Mission

NASA Technical Reports Server (NTRS)

Webb, Evan H.; Carlisle, Candace C.; Slavin, James A.

2005-01-01

The Space Technology 5 (ST-5) Project is part of NASA's New Millennium Program. ST-5 will consist of a constellation of three 25kg microsatellites. The mission goals are to demonstrate the research-quality science capability of the ST-5 spacecraft; to operate the three spacecraft as a constellation; and to design, develop and flight-validate three capable microsatellites with new technologies. ST-5 will be launched by a Pegasus XL into an elliptical polar (sun-synchronous) orbit. The three-month flight demonstration phase, beginning in March 2006, will validate the ability to perform science measurements, as well as the technologies and constellation operations. ST-5's technologies and concepts will enable future microsatellite science missions.

HDU Deep Space Habitat (DSH) Overview

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.

2011-01-01

This paper gives an overview of the National Aeronautics and Space Administration (NASA) led multi-center Habitat Demonstration Unit (HDU) project Deep Space Habitat (DSH) analog that will be field-tested during the 2011 Desert Research and Technologies Studies (D-RATS) field tests. The HDU project is a technology pull project that integrates technologies and innovations from multiple NASA centers. This project will repurpose the HDU Pressurized Excursion Module (PEM) that was field tested in the 2010 D-RATS, adding habitation functionality to the prototype unit. The 2010 configuration of the HDU-PEM consisted of a lunar surface laboratory module that was used to bring over 20 habitation-related technologies together in a single platform that could be tested as an advanced habitation analog in the context of mission architectures and surface operations. The 2011 HDU-DSH configuration will build upon the PEM work, and emphasize validity of crew operations (habitation and living, etc), EVA operations, mission operations, logistics operations, and science operations that might be required in a deep space context for Near Earth Object (NEO) exploration mission architectures. The HDU project consists of a multi-center team brought together in a skunkworks approach to quickly build and validate hardware in analog environments. The HDU project is part of the strategic plan from the Exploration Systems Mission Directorate (ESMD) Directorate Integration Office (DIO) and the Exploration Mission Systems Office (EMSO) to test destination elements in analog environments. The 2011 analog field test will include Multi Mission Space Exploration Vehicles (MMSEV) and the DSH among other demonstration elements to be brought together in a mission architecture context. This paper will describe overall objectives, various habitat configurations, strategic plan, and technology integration as it pertains to the 2011 field tests.

After The Demonstration: What States Sustained After the End of Federal Grants to Improve Children's Health Care Quality.

PubMed

Ireys, Henry T; Brach, Cindy; Anglin, Grace; Devers, Kelly J; Burton, Rachel

2018-02-01

Introduction Under the CHIPRA Quality Demonstration Grant Program, CMS awarded $100 million through 10 grants that 18 state Medicaid agencies implemented between 2010 and 2015. The program's legislatively-mandated purpose was to evaluate promising ideas for improving the quality of children's health care provided through Medicaid and CHIP. As part of the program's multifaceted evaluation, this study examined the extent to which states sustained key program activities after the demonstration ended. Methods We identified 115 potentially sustainable elements within states' CHIPRA demonstrations and analyzed data from grantee reports and key informant interviews to assess sustainment outcomes and key influential factors. We also assessed sustainment of the projects' intellectual capital. Results 56% of potentially sustainable elements were sustained. Sustainment varied by topic area: Elements related to quality measure reporting and practice facilitation were more likely to be sustained than others, such as parent advisors. Broad contextual factors, the state's Medicaid environment, implementation partners' resources, and characteristics of the demonstration itself all shaped sustainment outcomes. Discussion Assessing sustainment of key elements of states' CHIPRA quality demonstration projects provides insight into the fates of the "promising ideas" that the grant program was designed to examine. As a result of the federal government's investment in this grant program, many demonstration states are in a strong position to extend and spread specific strategies for improving the quality of care for children in Medicaid and CHIP. Our findings provide insights for policymakers and providers working to improve the quality of health care for low income children.

33 CFR Appendix A to Part 263 - History of Program and Project Limitations Continuing Authorities Program

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false History of Program and Project Limitations Continuing Authorities Program A Appendix A to Part 263 Navigation and Navigable Waters CORPS OF... Appendix A to Part 263—History of Program and Project Limitations Continuing Authorities Program Section...

34 CFR 461.33 - What are special experimental demonstration projects and teacher training projects?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 34 Education 3 2014-07-01 2014-07-01 false What are special experimental demonstration projects...? § 461.33 What are special experimental demonstration projects and teacher training projects? (a) In... personnel in programs designed to carry out the purposes of the Act; and (ii) Training professional teachers...

34 CFR 461.33 - What are special experimental demonstration projects and teacher training projects?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 34 Education 3 2011-07-01 2011-07-01 false What are special experimental demonstration projects...? § 461.33 What are special experimental demonstration projects and teacher training projects? (a) In... personnel in programs designed to carry out the purposes of the Act; and (ii) Training professional teachers...

34 CFR 461.33 - What are special experimental demonstration projects and teacher training projects?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 34 Education 3 2013-07-01 2013-07-01 false What are special experimental demonstration projects...? § 461.33 What are special experimental demonstration projects and teacher training projects? (a) In... personnel in programs designed to carry out the purposes of the Act; and (ii) Training professional teachers...

34 CFR 461.33 - What are special experimental demonstration projects and teacher training projects?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false What are special experimental demonstration projects...? § 461.33 What are special experimental demonstration projects and teacher training projects? (a) In... personnel in programs designed to carry out the purposes of the Act; and (ii) Training professional teachers...

34 CFR 461.33 - What are special experimental demonstration projects and teacher training projects?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 34 Education 3 2012-07-01 2012-07-01 false What are special experimental demonstration projects...? § 461.33 What are special experimental demonstration projects and teacher training projects? (a) In... personnel in programs designed to carry out the purposes of the Act; and (ii) Training professional teachers...

34 CFR 425.1 - What is the Demonstration Projects for the Integration of Vocational and Academic Learning Program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false What is the Demonstration Projects for the Integration... EDUCATION DEMONSTRATION PROJECTS FOR THE INTEGRATION OF VOCATIONAL AND ACADEMIC LEARNING PROGRAM General § 425.1 What is the Demonstration Projects for the Integration of Vocational and Academic Learning...

NASA Electronic Parts and Packaging Program

NASA Technical Reports Server (NTRS)

Kayali, Sammy

2000-01-01

NEPP program objectives are to: (1) Access the reliability of newly available electronic parts and packaging technologies for usage on NASA projects through validations, assessments, and characterizations, and the development of test methods/tools; (2)Expedite infusion paths for advanced (emerging) electronic parts and packaging technologies by evaluations of readiness for manufacturability and project usage consideration; (3) Provide NASA projects with technology selection, application, and validation guidelines for electronic parts and packaging hardware and processes; nd (4) Retain and disseminate electronic parts and packaging quality assurance, reliability validations, tools, and availability information to the NASA community.

Sines and Cosines. Part 2 of 3

NASA Technical Reports Server (NTRS)

Apostol, Tom M. (Editor)

1993-01-01

The Law of Sines and the Law of Cosines are introduced and demonstrated in this 'Project Mathematics' series video using both film footage and computer animation. This video deals primarily with the mathematical field of Trigonometry and explains how these laws were developed and their applications. One significant use is geographical and geological surveying. This includes both the triangulation method and the spirit leveling method. With these methods, it is shown how the height of the tallest mountain in the world, Mt. Everest, was determined.

A methodology for hypersonic transport technology planning

NASA Technical Reports Server (NTRS)

Repic, E. M.; Olson, G. A.; Milliken, R. J.

1973-01-01

A systematic procedure by which the relative economic value of technology factors affecting design, configuration, and operation of a hypersonic cruise transport can be evaluated is discussed. Use of the methodology results in identification of first-order economic gains potentially achievable by projected advances in each of the definable, hypersonic technologies. Starting with a baseline vehicle, the formulas, procedures and forms which are integral parts of this methodology are developed. A demonstration of the methodology is presented for one specific hypersonic vehicle system.

VHF downline communication system for SLAR data

NASA Technical Reports Server (NTRS)

Schertler, R. J.; Chase, T. L.; Mueller, R. A.; Kramarchuk, I.; Jirberg, R. J.; Gedney, R. T.

1979-01-01

A real time VHF downlink communication system is described for transmitting side-looking airborne radar (SLAR) data directly from an aircraft to a portable ground/shipboard receiving station. Use of this receiving station aboard the U.S. Coast Guard icebreaker Mackinaw for generating real-time photographic quality radar images is discussed. The system was developed and demonstrated in conjunction with the U.S Coast Guard and NOAA National Weather Service as part of the Project Icewarn all weather ice information system for the Great Lakes Winter Navigation Program.

The Majorana Project

ScienceCinema

Orrell, John; Hoppe, Eric

2018-01-26

Working as part of a collaborative team, PNNL is bringing its signature capability in ultra-low-level detection to help search for a rare form of radioactive decay-never before detected-called "neutrinoless double beta decay" in germanium. If observed, it would demonstrate neutrinos are Majorana-type particles. This discovery would show neutrinos are unique among fundamental particles, having a property whereby the matter and anti-matter version of this particle are indistinguishable. Physicist John L. Orrell explains how they rely on the Shallow Underground Laboratory to conduct the research.

Photovoltaic power system reliability considerations

NASA Technical Reports Server (NTRS)

Lalli, V. R.

1980-01-01

An example of how modern engineering and safety techniques can be used to assure the reliable and safe operation of photovoltaic power systems is presented. This particular application is for a solar cell power system demonstration project designed to provide electric power requirements for remote villages. The techniques utilized involve a definition of the power system natural and operating environment, use of design criteria and analysis techniques, an awareness of potential problems via the inherent reliability and FMEA methods, and use of fail-safe and planned spare parts engineering philosophy.

GE STEM Teacher's Conference

NASA Image and Video Library

2017-07-13

Teachers prepare to demonstrate the projects they built for the Rocketry Engineering Design Challenge during the 2017 GE Foundation High School STEM Integration Conference at the Center for Space Education at NASA's Kennedy Space Center. High school teachers from across the country took part in the week-long conference, which is designed to explore effective ways for teachers, schools and districts from across the country to integrate STEM throughout the curriculum. The conference is a partnership between GE Foundation and the National Science Teachers Association.

Sines and Cosines. Part 3 of 3

NASA Technical Reports Server (NTRS)

Apostol, Tom M. (Editor)

1994-01-01

In this 'Project Mathematics' series video, the addition formulas of sines and cosines are explained and their real life applications are demonstrated. Both film footage and computer animation is used. Several mathematical concepts are discussed and include: Ptolemy's theorem concerned with quadrilaterals; the difference between a central angle and an inscribed angle; sines and chord lengths; special angles; subtraction formulas; and a application to simple harmonic motion. A brief history of the city Alexandria, its mathematicians, and their contribution to the field of mathematics is shown.

A methodology for boost-glide transport technology planning

NASA Technical Reports Server (NTRS)

Repic, E. M.; Olson, G. A.; Milliken, R. J.

1974-01-01

A systematic procedure is presented by which the relative economic value of technology factors affecting design, configuration, and operation of boost-glide transport can be evaluated. Use of the methodology results in identification of first-order economic gains potentially achievable by projected advances in each of the definable, hypersonic technologies. Starting with a baseline vehicle, the formulas, procedures and forms which are integral parts of this methodology are developed. A demonstration of the methodology is presented for one specific boost-glide system.

Photovoltaic power system reliability considerations

NASA Technical Reports Server (NTRS)

Lalli, V. R.

1980-01-01

This paper describes an example of how modern engineering and safety techniques can be used to assure the reliable and safe operation of photovoltaic power systems. This particular application was for a solar cell power system demonstration project in Tangaye, Upper Volta, Africa. The techniques involve a definition of the power system natural and operating environment, use of design criteria and analysis techniques, an awareness of potential problems via the inherent reliability and FMEA methods, and use of a fail-safe and planned spare parts engineering philosophy.

Project BudBurst - Meeting the Needs of Climate Change Educators and Scientists

NASA Astrophysics Data System (ADS)

Henderson, S.

2015-12-01

It is challenging for many to get a sense of what climate change means as long periods of time are involved - like decades - which can be difficult to grasp. However, there are a number of citizen science based projects, including NEON's Project BudBurst, that provide the opportunity for both learning about climate change and advancing scientific knowledge. In this presentation, we will share lessons learned from Project BudBurst. Project BudBurst is a national citizen science initiative designed to engage the public in observations of phenological (plant life cycle) events and to increase climate literacy. Project BudBurst is important from an educational perspective, but also because it enables scientists to broaden the geographic and temporal scale of their observations. The goals of Project BudBurst are to 1) increase awareness of phenology as an area of scientific study; 2) Increase awareness of the impacts of changing climates on plants at a continental-scale; and 3) increase science literacy by engaging participants in the scientific process. It was important to better understand if and how Project BudBurst is meeting its goals. Specifically, does participation by non-experts advance scientific knowledge? Does participation advance educational goals and outcomes? Is participation an effective approach to advance/enhance science education in both formal and informal settings? Critical examination of Project BudBurst supports advancement of scientific knowledge and realization of educational objectives. Citizen science collected observations and measurements are being used by scientists as evidenced by the increase of such data in scientific publication. In addition, we found that there is a significant increase in educators utilizing citizen science as part of their instruction. Part of this increase is due to the resources and professional development materials available to educators. Working with partners also demonstrated that the needs of both science and education are being met. Project BudBurst, partners with the PhenoCam Network, National Geographic Society, US Fish and Wildlife Service, National Park Service botanic gardens, science centers and other organizations with both a scientific and educational mission.

Effectively dealing with state and federal regulators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zebrowski, S.M.

1997-08-01

Environmental compliance is an essential part of every business practice in today`s world. For almost a quarter of a century, the nation has been involved in environmental restoration of contaminated sites. Over the years, the science and engineering required to remediate these sites has been developed and well documented. However, there is one major part of the environmental cleanup business that still alludes much of the regulated community. Communication skills required for successful project execution have not been well studied or documented. It is only in retrospect that man can look back on experiences and learn, then document how onemore » can better communicate with the regulators and stakeholders for future environmental compliance and cleanup work. The intent of this paper is to present the management skills learned from past experiences that would facilitate the effective communications between the regulated community, regulators and stakeholders during site remediation. Lessons learned from the past demonstrate that sometimes remediations are driven not solely by engineering and science, but also in part by emotions and politics. Other lessons demonstrate that communications with the regulators and stakeholders should begin very early in the remediation process.« less

ALTUS Cumulus Electrification Study (ACES)

NASA Technical Reports Server (NTRS)

Kim, Tony; Blakeslee, Richard; Russell, Larry W. (Technical Monitor)

2002-01-01

The ALTUS Cumulus Electrification Study (ACES) is an uninhabited aerial vehicle (UAV)-based project that will investigate thunderstorms in the vicinity of the Florida Everglades in August 2002. ACES is being conducted to both investigate storm electrical activity and its relationship to storm morphology, and validate Tropical Rainfall Measurement Mission (TRMM) satellite measurements. In addition, as part of NASA's UAV-based science demonstration program, this project will provide a scientifically useful demonstration of the utility and promise of UAV platforms for Earth science and applications observations. Part of the demonstration involves getting approvals from the Federal Aviation Administration and the NASA airworthiness flight safety review board. ACES will employ the ALTUS II aircraft, built by General Atomics - Aeronautical Systems, Inc. Key science objectives simultaneously addressed by ACES are to: (1) investigate lightning-storm relationships, (2) study storm electrical budgets, and (3) provide Lightning Imaging Sensor validation. The ACES payload, already developed and flown on ALTUS, includes electrical, magnetic, and optical sensors to remotely characterize the lightning activity and the electrical environment within and around thunderstorms. ACES will contribute important electrical and optical measurements not available from other sources. Also, the high altitude vantage point of the UAV observing platform (up to 55,000 feet) offers a useful 'cloud-top' perspective. By taking advantage of its slow flight speed (70 to 100 knots), long endurance, and high altitude flight, the ALTUS will be flown near, and when possible, above (but never into) thunderstorms for long periods of time, allowing investigations to be conducted over entire storm life cycles. In addition, concurrent ground-based observations will enable the UAV measurements to be more completely interpreted and evaluated in the context of the thunderstorm structure, evolution, and environment.

23 CFR 636.104 - Does this part apply to all Federal-aid design-build projects?

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Does this part apply to all Federal-aid design-build projects? 636.104 Section 636.104 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS DESIGN-BUILD CONTRACTING General § 636.104 Does this part apply to all Federal-aid design-build projects? The...

In Situ Fringe Projection Profilometry for Laser Power Bed Fusion Process

NASA Astrophysics Data System (ADS)

Zhang, Bin

Additive manufacturing (AM) offers an industrial solution to produce parts with complex geometries and internal structures that conventional manufacturing techniques cannot produce. However, current metal additive process, particularly the laser powder bed fusion (LPBF) process, suffers from poor surface finish and various material defects which hinder its wide applications. One way to solve this problem is by adding in situ metrology sensor onto the machine chamber. Matured manufacturing processes are tightly monitored and controlled, and instrumentation advances are needed to realize this same advantage for metal additive process. This encourages us to develop an in situ fringe projection system for the LPBF process. The development of such a system and the measurement capability are demonstrated in this dissertation. We show that this system can measure various powder bed signatures including powder layer variations, the average height drop between fused metal and unfused powder, and the height variations on the fused surfaces. The ability to measure textured surface is also evaluated through the instrument transfer function (ITF). We analyze the mathematical model of the proposed fringe projection system, and prove the linearity of the system through simulations. A practical ITF measurement technique using a stepped surface is also demonstrated. The measurement results are compared with theoretical predictions generated through the ITF simulations.

Discussion series on PURPA related topics: load management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sturgeon, J I

The Discussion Series on PURPA Related Topics is composed of five volumes: Metering, Billing, Information to Customers, Load Management Techniques and Master Metering. These reports are based on twenty-five Demonstration and Implementation projects sponsored and directed during the past five years by the US Department of Energy, Office of Utility Systems. Each of the topics bears directly on one or more of the federal standards contained in the Public Utilities Regulatory Policies Act of 1978 (PURPA). This volume, Load Management Techniques, relates primarily to the Time-of-Day rates standard, PURPA IB(d)3. The experiences related in this report deal, in part, withmore » the procedures and equipment which are affected when time-of-day rates are implemented. One goal of this report is to describe how people in a variety of settings have dealt with the many practical issues in load management. Another is to highlight the lessons and summarize the experiences of the Project participants. This report does not stand as a manual nor provide prescriptive guidelines on how to deal with the topic. Rather it offers an account for those charged with the responsibility of implementing PURPA requirements to learn from the insights and problems which occurred during the Rate Demonstration projects.« less

Pecan Street Grid Demonstration Program. Final technology performance report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

This document represents the final Regional Demonstration Project Technical Performance Report (TPR) for Pecan Street Inc.’s (Pecan Street) Smart Grid Demonstration Program, DE-OE-0000219. Pecan Street is a 501(c)(3) smart grid/clean energy research and development organization headquartered at The University of Texas at Austin (UT). Pecan Street worked in collaboration with Austin Energy, UT, Environmental Defense Fund (EDF), the City of Austin, the Austin Chamber of Commerce and selected consultants, contractors, and vendors to take a more detailed look at the energy load of residential and small commercial properties while the power industry is undergoing modernization. The Pecan Street Smart Gridmore » Demonstration Program signed-up over 1,000 participants who are sharing their home or businesses’s electricity consumption data with the project via green button protocols, smart meters, and/or a home energy monitoring system (HEMS). Pecan Street completed the installation of HEMS in 750 homes and 25 commercial properties. The program provided incentives to increase the installed base of roof-top solar photovoltaic (PV) systems, plug-in electric vehicles with Level 2 charging, and smart appliances. Over 200 participants within a one square mile area took advantage of Austin Energy and Pecan Street’s joint PV incentive program and installed roof-top PV as part of this project. Of these homes, 69 purchased or leased an electric vehicle through Pecan Street’s PV rebate program and received a Level 2 charger from Pecan Street. Pecan Street studied the impacts of these technologies along with a variety of consumer behavior interventions, including pricing models, real-time feedback on energy use, incentive programs, and messaging, as well as the corresponding impacts on Austin Energy’s distribution assets.The primary demonstration site was the Mueller community in Austin, Texas. The Mueller development, located less than three miles from the Texas State Capitol, is a 711-acre LEED Neighborhood Development mixed-use, urban infill redevelopment on the site of Austin’s former airport, currently under development through a public-private project between the City of Austin, and Catellus Austin LLC. Currently, Mueller is less than 50% complete and more than 3,500 people live or work at Mueller. At full build-out, the project will include more than 3 million square feet of commercial and institutional space, more than 13,000 residents from approximately 5,700 single-family and multi-family dwelling units. Figure 1 shows a Google Map image of the Mueller community, zoomed in on the residential streets participating in the project.« less

Mars Spark Source Prototype Developed

NASA Technical Reports Server (NTRS)

Eichenberg, Dennis J.; Lindamood, Glenn R.; VanderWal, Randall L.; Weiland, Karen J.

2000-01-01

The Mars Spark Source Prototype (MSSP) hardware was developed as part of a proof of concept system for the detection of trace metals such as lead, cadmium, and arsenic in Martian dusts and soils. A spark discharge produces plasma from a soil sample, and detectors measure the optical emission from metals in the plasma to identify and quantify them. Trace metal measurements are vital in assessing whether or not the Martian environment will be toxic to human explorers. The current method of x-ray fluorescence can yield concentrations of major species only. Other instruments are incompatible with the volume, weight, and power constraints for a Mars mission. The new instrument will be developed primarily for use in the Martian environment, but it would be adaptable for terrestrial use in environmental monitoring. The NASA Glenn Research Center at Lewis Field initiated the development of the MSSP as part of Glenn's Director's Discretionary Fund project for the Spark Analysis Detection of Trace Metal Species in Martian Dusts and Soils. The objective of this project is to develop and demonstrate a compact, sensitive optical instrument for the detection of trace hazardous metals in Martian dusts and soils.

Dragonfly: strengthening programming skills by building a game engine from scratch

NASA Astrophysics Data System (ADS)

Claypool, Mark

2013-06-01

Computer game development has been shown to be an effective hook for motivating students to learn both introductory and advanced computer science topics. While games can be made from scratch, to simplify the programming required game development often uses game engines that handle complicated or frequently used components of the game. These game engines present the opportunity to strengthen programming skills and expose students to a range of fundamental computer science topics. While educational efforts have been effective in using game engines to improve computer science education, there have been no published papers describing and evaluating students building a game engine from scratch as part of their course work. This paper presents the Dragonfly-approach in which students build a fully functional game engine from scratch and make a game using their engine as part of a junior-level course. Details on the programming projects are presented, as well as an evaluation of the results from two offerings that used Dragonfly. Student performance on the projects as well as student assessments demonstrates the efficacy of having students build a game engine from scratch in strengthening their programming skills.

Imaging of spatial distributions of the millimeter wave intensity by using the Visible Continuum Radiation from a discharge in a Cs-Xe mixture. Part II: Demonstration of application capabilities of the technique

NASA Astrophysics Data System (ADS)

Gitlin, M. S.; Glyavin, M. Yu.; Fedotov, A. E.; Tsvetkov, A. I.

2017-07-01

The paper presents the second part of the review on a high-sensitive technique for time-resolved imaging and measurements of the 2D intensity profiles of millimeter-wave radiation by means of Visible Continuum Radiation emitted by the positive column of a medium-pressure Cs-Xe DC Discharge (VCRD method). The first part of the review was focused on the operating principles and fundamentals of this new technique [Plasma Phys. Rep. 43, 253 (2017)]. The second part of the review focuses on experiments demonstrating application of this imaging technique to measure the parameters of radiation at the output of moderate-power millimeter-wave sources. In particular, the output waveguide mode of a moderate-power W-band gyrotron with a pulsed magnetic field was identified and the relative powers of some spurious modes at the outputs of this gyrotron and a pulsed D-band orotron were evaluated. The paper also reviews applications of the VCRD technique for real-time imaging and nondestructive testing with a frame rate of higher than 10 fps by using millimeter waves. Shadow projection images of objects opaque and transparent for millimeter waves have been obtained using pulsed watt-scale millimeter waves for object illumination. Near video frame rate millimeter-wave shadowgraphy has been demonstrated. It is shown that this technique can be used for single-shot screening (including detection of concealed objects) and time-resolved imaging of time-dependent processes.

Nuclear facility decommissioning and site remedial actions: A selected bibliography, Vol. 18. Part 2. Indexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-09-01

This bibliography contains 3638 citations with abstracts of documents relevant to environmental restoration, nuclear facility decontamination and decommissioning (D&D), uranium mill tailings management, and site remedial actions. This report is the eighteenth in a series of bibliographies prepared annually for the U.S. Department of Energy (DOE) Office of Environmental Restoration. Citations to foreign and domestic literature of all types - technical reports, progress reports, journal articles, symposia proceedings, theses, books, patents, legislation, and research project descriptions - have been included in Part 1 of the report. The bibliography contains scientific, technical, financial, and regulatory information that pertains to DOE environmentalmore » restoration programs. The citations are separated by topic into 16 sections, including (1) DOE Environmental Restoration Program; (2) DOE D&D Program; (3) Nuclear Facilities Decommissioning; (4) DOE Formerly Utilized Sites Remedial Action Programs; (5) NORM-Contaminated Site Restoration; (6) DOE Uranium Mill Tailings Remedial Action Project; (7) Uranium Mill Tailings Management; (8) DOE Site-Wide Remedial Actions; (9) DOE Onsite Remedial Action Projects; (10) Contaminated Site Remedial Actions; (11) DOE Underground Storage Tank Remediation; (12) DOE Technology Development, Demonstration, and Evaluations; (13) Soil Remediation; (14) Groundwater Remediation; (15) Environmental Measurements, Analysis, and Decision-Making; and (16) Environmental Management Issues. Within the 16 sections, the citations are sorted by geographic location. If a geographic location is not specified, the citations are sorted according to the document title. In Part 2 of the report, indexes are provided for author, author affiliation, selected title phrase, selected title word, publication description, geographic location, and keyword.« less

A New Look For Greenbelt

NASA Technical Reports Server (NTRS)

1978-01-01

Greenbelt, Maryland, 12 miles from the nation's capital, is an efficiently planned model town and most of its 1600 homes are almost identical in appearance. Four of them, however, stand out from their neighbors; they have distinctive blue glass rooftop superstructures made up of a series of solar collectors. They are part of a NASA community aid program, a joint energy research project involving the Greenbelt housing cooperative and NASA's Goddard Space Flight Center, located near the community. Built in 1935, Greenbelt is one of three government-planned communities of President Franklin D. Roosevelt's first administration; the others are Greendale, Wisconsin and Greenhills, Ohio. The government built the towns to make available low-cost housing, provide employment for workers on relief in the Great Depression era, and to establish models designed to encourage construction of similar developments by private industry. In 1952, the residents of Greenbelt formed a nonprofit cooperative called Greenbelt Homes, Inc., which bought the dwellings, facilities and a large part of the land from the government. The homes are individually owned but collectively maintained by the co-op, with each owner paying a prorated share of utility and maintenance costs. Greenbelt residents are mostly in the low and medium income brackets, and one of every three families lives on a fixed retirement income. For that reason, the sharp escalation of fuel oil prices that began in 1973 imposed particular hardship on the co-op community. So Greenbelt Homes' management asked its NASA neighbor, Goddard Space Flight Center, for assistance in setting up a solar energy research project. The idea was to conduct a small scale demonstration to show what savings could be realized by solar heating Greenbelt homes, with an eye toward possible future expansion of solar energy systems as a means of combating rising fuel costs. Goddard undertook the project as part of the federal government's effort to research and demonstrate ways of conserving energy. The Center was well qualified for the assignment, having acquired extensive expertise in designing thermal control systems for satellites, which must maintain stable temperatures for successful operation.

2+2+2 Dissemination Project Final Report.

ERIC Educational Resources Information Center

Sloane, Diana; And Others

An overview is provided in this three-part final report of a project designed to disseminate information to assist California high schools, Regional Occupation Programs, and colleges in developing and strengthening 2+2+2 programs. Part I reviews the following project objectives: (1) hire a project coordinator and technical assistant; (2) develop a…

Project Bibliographies: Tracking the Expansion of Knowledge Using JPL Project Publications

ERIC Educational Resources Information Center

Coppin, Ann

2016-01-01

The Jet Propulsion Laboratory (JPL) Library defines a project bibliography as a bibliography of publicly available publications relating to a specific JPL instrument or mission. These bibliographies may be used to share information between distant project team members, as part of the required Education and Public Outreach effort, or as part of…

Practical Elements in Danish Engineering Programmes, Including the European Project Semester

ERIC Educational Resources Information Center

Hansen, Jorgen

2012-01-01

In Denmark, all engineering programmes in HE have practical elements; for instance, at Bachelor's level, an internship is an integrated part of the programme. Furthermore, Denmark has a long-established tradition of problem-based and project-organized learning, and a large part of students' projects, including their final projects, is done in…

18 CFR 4.103 - General provisions for case-specific exemption.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., EXEMPTIONS, AND DETERMINATION OF PROJECT COSTS Exemption of Small Hydroelectric Power Projects of 5 Megawatts or Less § 4.103 General provisions for case-specific exemption. (a) Exemptible projects. Subject to... exempt on a case-specific basis any small hydroelectric power project from all or part of Part I of the...

18 CFR 4.103 - General provisions for case-specific exemption.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., EXEMPTIONS, AND DETERMINATION OF PROJECT COSTS Exemption of Small Hydroelectric Power Projects of 5 Megawatts or Less § 4.103 General provisions for case-specific exemption. (a) Exemptible projects. Subject to... exempt on a case-specific basis any small hydroelectric power project from all or part of Part I of the...

18 CFR 4.103 - General provisions for case-specific exemption.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., EXEMPTIONS, AND DETERMINATION OF PROJECT COSTS Exemption of Small Hydroelectric Power Projects of 5 Megawatts or Less § 4.103 General provisions for case-specific exemption. (a) Exemptible projects. Subject to... exempt on a case-specific basis any small hydroelectric power project from all or part of Part I of the...

18 CFR 4.103 - General provisions for case-specific exemption.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., EXEMPTIONS, AND DETERMINATION OF PROJECT COSTS Exemption of Small Hydroelectric Power Projects of 5 Megawatts or Less § 4.103 General provisions for case-specific exemption. (a) Exemptible projects. Subject to... exempt on a case-specific basis any small hydroelectric power project from all or part of Part I of the...

18 CFR 4.103 - General provisions for case-specific exemption.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., EXEMPTIONS, AND DETERMINATION OF PROJECT COSTS Exemption of Small Hydroelectric Power Projects of 5 Megawatts or Less § 4.103 General provisions for case-specific exemption. (a) Exemptible projects. Subject to... exempt on a case-specific basis any small hydroelectric power project from all or part of Part I of the...

An App for the Cathedral in Freiberg--An Interdisciplinary Project Seminar

ERIC Educational Resources Information Center

Kröber, Cindy; Münster, Sander

2014-01-01

This project seminar aims at creating and evaluating a manual for interdisciplinary projects as part of a learning process. Working together, pedagogies and students from different disciplines assess tools and recommendations for successful collaborations while developing an app for the cathedral in Freiberg. As part of the project the students…

Multibeam Phased Array Antennas

NASA Technical Reports Server (NTRS)

Popovic, Zoya; Romisch, Stefania; Rondineau, Sebastien

2004-01-01

In this study, a new architecture for Ka-band multi-beam arrays was developed and demonstrated experimentally. The goal of the investigation was to demonstrate a new architecture that has the potential of reducing the cost as compared to standard expensive phased array technology. The goals of this specific part of the project, as stated in the yearly statement of work in the original proposal are: 1. Investigate bounds on performance of multi-beam lens arrays in terms of beamwidths, volume (size), isolation between beams, number of simultaneous beams, etc. 2. Design a small-scale array to demonstrate the principle. The array will be designed for operation around 3OGHz (Ka-band), with two 10-degree beamwidth beams. 3. Investigate most appropriate way to accomplish fine-tuning of the beam pointing within 5 degrees around the main beam pointing angle.

Science in bullet points: How to compile scientific results to underpin guidelines for CO2 storage for the German transposition of the European CCS Directive

NASA Astrophysics Data System (ADS)

Streibel, Martin

2015-04-01

In 2012 the German Parliament passed the transposition of the EC Directive 2009/31/EC the "Carbon Dioxide Storage Law" (KSpG). The law focuses on the demonstration of the CO2 storage technology and mainly regulates the storage part of the Carbon Capture and Storage (CCS) chain. As the law has a conceptual character, appendix 1 provides a description of criteria for the characterisation and assessment of a potential CO2 storage site starting with field data ending with requirements for dynamic modelling of the storage complex. Appendix 2 describes the expected monitoring system during all relevant phases of a life cycle of a CO2 storage site. The criteria given in the appendices are of general nature, which reflects on one hand that the CO2 storage technology is still being developed and on the other hand that site specific aspects needs to be considered. In 2004 the Federal Ministry of Education and Research of Germany launched the programme GEOTECHNOLOGIEN with one key aspect being the development of technologies for a sustainable storage of carbon dioxide in geological formations. Within this research field more than 30 projects in three phases have been funded until the end of 2014. In order to benefit from the gathered knowledge and use the experiences for the policy/law making process the umbrella project AUGE has been launched in October 2012 with a life time of three years. The aim of the project is to review and compile all results of projects funded during the three phases to underpin the appendices of the KSpG. In the first part of the paper the most important findings of the project with regard to the overall risk of a geological CO2 storage and the procedure of compiling the guidance document will be discussed. Milestones of this project were • the compilation of the results of national, European and international projects; • interviews with stakeholders; • a workshops to define state of the art for certain involved technologies and existing gaps; • a workshop to understand the limitations of existing simulation tools for large scale CO2 storage. In a second part of the paper it is discussed what kind of guidance documents are actually still required for regulation of large scale CO2 storage sites.

A system dynamics model of a large R&D program

NASA Astrophysics Data System (ADS)

Ahn, Namsung

Organizations with large R&D activities must deal with a hierarchy of decision regarding resource allocation. At the highest level of allocation, the decision is related to the total allocation to R&D as some portion of revenue. The middle level of allocation deals with the allocation among phases of the R&D process. The lowest level of decisions relates to the resource allocation to specific projects within a specific phase. This study focuses on developing an R&D model to deal with the middle level of allocation, i.e., the allocation among phases of research such as basic research, development, and demonstration. The methodology used to develop the R&D model is System Dynamics. Our modeling concept is innovative in representing each phase of R&D as consisting of two parts: projects under way, and an inventory of successful but not-yet- exploited projects. In a simple world, this concept can yield an exact analytical solution for allocation of resources among phases. But in a real world, the concept should be improved by adding more complex structures with nonlinear behaviors. Two particular nonlinear feedbacks are incorporated into the R&D model. The probability of success for any specific project is assumed partly dependent upon resources allocated to the project. Further, the time required to reach a conclusion regarding the success or failure of a project is also assumed dependent upon the level of resources allocated. In addition, the number of successful projects partly depends on the inventory of potential ideas in the previous stage that can be exploited. This model can provide R&D management with insights into the effect of changing allocations to phases whether those changes are internally or externally driven. With this model, it is possible to study the effectiveness of management decisions in a continuous fashion. Managers can predict payoffs for a host of different policies. In addition, as new research results accumulate, a re- assessment of program goals can be implemented easily and allocations adjusted to enhance continuously the likelihood of success, and to optimize payoffs. Finally, this model can give managers a quantitative rationale for program evaluation and permit the quantitative assessment of various externally imposed changes. (Copies available exclusively from MIT Libraries, Rm. 14-0551, Cambridge, MA 02139-4307. Ph. 617-253-5668; Fax 617-253-1690.)

A Study of Four Library Programs for Disadvantaged Persons. Part II, Appendices B: Brooklyn Public Library Community Coordinator Project, the New York Public Library North Manhattan Project.

ERIC Educational Resources Information Center

Winsor, Charlotte B.; Burrows, Lodema

This document contains observations of library staff and interviews with community members about the Brooklyn Public Library Community Coordinator Project and the New York Public Library North Manhattan Project. The Community Coordinator Project employs four professional librarians to take an active part in community institutions and organizations…

Systems Engineering and Reusable Avionics

NASA Technical Reports Server (NTRS)

Conrad, James M.; Murphy, Gloria

2010-01-01

One concept for future space flights is to construct building blocks for a wide variety of avionics systems. Once a unit has served its original purpose, it can be removed from the original vehicle and reused in a similar or dissimilar function, depending on the function blocks the unit contains. For example: Once a lunar lander has reached the moon's surface, an engine controller for the Lunar Decent Module would be removed and used for a lunar rover motor control unit or for a Environmental Control Unit for a Lunar Habitat. This senior design project included the investigation of a wide range of functions of space vehicles and possible uses. Specifically, this includes: (1) Determining and specifying the basic functioning blocks of space vehicles. (2) Building and demonstrating a concept model. (3) Showing high reliability is maintained. The specific implementation of this senior design project included a large project team made up of Systems, Electrical, Computer, and Mechanical Engineers/Technologists. The efforts were made up of several sub-groups that each worked on a part of the entire project. The large size and complexity made this project one of the more difficult to manage and advise. Typical projects only have 3-4 students, but this project had 10 students from five different disciplines. This paper describes the difference of this large project compared to typical projects, and the challenges encountered. It also describes how the systems engineering approach was successfully implemented so that the students were able to meet nearly all of the project requirements.

HESTIA Commodities Exchange Pallet and Sounding Rocket Test Stand

NASA Technical Reports Server (NTRS)

Chaparro, Javier

2013-01-01

During my Spring 2016 internship, my two major contributions were the design of the Commodities Exchange Pallet and the design of a test stand for a 100 pounds-thrust sounding rocket. The Commodities Exchange Pallet is a prototype developed for the Human Exploration Spacecraft Testbed for Integration and Advancement (HESTIA) program. Under the HESTIA initiative the Commodities Exchange Pallet was developed as a method for demonstrating multi-system integration thru the transportation of In-Situ Resource Utilization produced oxygen and water to a human habitat. Ultimately, this prototype's performance will allow for future evaluation of integration, which may lead to the development of a flight capable pallet for future deep-space exploration missions. For HESTIA, my main task was to design the Commodities Exchange Pallet system to be used for completing an integration demonstration. Under the guidance of my mentor, I designed, both, the structural frame and fluid delivery system for the commodities pallet. The fluid delivery system includes a liquid-oxygen to gaseous-oxygen system, a water delivery system, and a carbon-dioxide compressors system. The structural frame is designed to meet safety and transportation requirements, as well as the ability to interface with the ER division's Portable Utility Pallet. The commodities pallet structure also includes independent instrumentation oxygen/water panels for operation and system monitoring. My major accomplishments for the commodities exchange pallet were the completion of the fluid delivery systems and the structural frame designs. In addition, parts selection was completed in order to expedite construction of the prototype, scheduled to begin in May of 2016. Once the commodities pallet is assembled and tested it is expected to complete a fully integrated transfer demonstration with the ISRU unit and the Environmental Control and Life Support System test chamber in September of 2016. In addition to the development of the Commodities Exchange Pallet, I also assisted in preparation for testing the upper stage of a sounding rocket developed as a Center Innovation Fund project. The main objective of this project is to demonstrate the integration between a propulsion system and a solid oxide fuel cell (SOFC). The upper stage and SOFC are scheduled to complete an integrated test in August of 2016. As part of preparation for scheduled testing, I was responsible for designing the upper stage's test stand/support structure and main engine plume deflector to be used during hot-fire testing (fig. 3). The structural components of the test stand need to meet safety requirements for operation of the propulsion system, which consist of a 100 pounds-thrust main engine and two 15 pounds-thrust reaction control thrusters. My main accomplishment for this project was the completion of the design and the parts selection for construction of the structure, scheduled to begin late April of 2016.

Perspective: Role of structure prediction in materials discovery and design

NASA Astrophysics Data System (ADS)

Needs, Richard J.; Pickard, Chris J.

2016-05-01

Materials informatics owes much to bioinformatics and the Materials Genome Initiative has been inspired by the Human Genome Project. But there is more to bioinformatics than genomes, and the same is true for materials informatics. Here we describe the rapidly expanding role of searching for structures of materials using first-principles electronic-structure methods. Structure searching has played an important part in unraveling structures of dense hydrogen and in identifying the record-high-temperature superconducting component in hydrogen sulfide at high pressures. We suggest that first-principles structure searching has already demonstrated its ability to determine structures of a wide range of materials and that it will play a central and increasing part in materials discovery and design.

Strategy Guideline. Demonstration Home

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunt, A.; Savage, C.

2012-12-01

This guideline will provide a general overview of the different kinds of demonstration home projects, a basic understanding of the different roles and responsibilities involved in the successful completion of a demonstration home, and an introduction into some of the lessons learned from actual demonstration home projects. Also, this guideline will specifically look at the communication methods employed during demonstration home projects. And lastly, we will focus on how to best create a communication plan for including an energy efficient message in a demonstration home project and carry that message to successful completion.

Strategy Guideline: Demonstration Home

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savage, C.; Hunt, A.

2012-12-01

This guideline will provide a general overview of the different kinds of demonstration home projects, a basic understanding of the different roles and responsibilities involved in the successful completion of a demonstration home, and an introduction into some of the lessons learned from actual demonstration home projects. Also, this guideline will specifically look at the communication methods employed during demonstration home projects. And lastly, we will focus on how to best create a communication plan for including an energy efficient message in a demonstration home project and carry that message to successful completion.

Predicting long-term graft survival in adult kidney transplant recipients.

PubMed

Pinsky, Brett W; Lentine, Krista L; Ercole, Patrick R; Salvalaggio, Paolo R; Burroughs, Thomas E; Schnitzler, Mark A

2012-07-01

The ability to accurately predict a population's long-term survival has important implications for quantifying the benefits of transplantation. To identify a model that can accurately predict a kidney transplant population's long-term graft survival, we retrospectively studied the United Network of Organ Sharing data from 13,111 kidney-only transplants completed in 1988- 1989. Nineteen-year death-censored graft survival (DCGS) projections were calculated and compared with the population's actual graft survival. The projection curves were created using a two-part estimation model that (1) fits a Kaplan-Meier survival curve immediately after transplant (Part A) and (2) uses truncated observational data to model a survival function for long-term projection (Part B). Projection curves were examined using varying amounts of time to fit both parts of the model. The accuracy of the projection curve was determined by examining whether predicted survival fell within the 95% confidence interval for the 19-year Kaplan-Meier survival, and the sample size needed to detect the difference in projected versus observed survival in a clinical trial. The 19-year DCGS was 40.7% (39.8-41.6%). Excellent predictability (41.3%) can be achieved when Part A is fit for three years and Part B is projected using two additional years of data. Using less than five total years of data tended to overestimate the population's long-term survival, accurate prediction of long-term DCGS is possible, but requires attention to the quantity data used in the projection method.

Probabilistic inversion of expert assessments to inform projections about Antarctic ice sheet responses

PubMed Central

Wong, Tony E.; Keller, Klaus

2017-01-01

The response of the Antarctic ice sheet (AIS) to changing global temperatures is a key component of sea-level projections. Current projections of the AIS contribution to sea-level changes are deeply uncertain. This deep uncertainty stems, in part, from (i) the inability of current models to fully resolve key processes and scales, (ii) the relatively sparse available data, and (iii) divergent expert assessments. One promising approach to characterizing the deep uncertainty stemming from divergent expert assessments is to combine expert assessments, observations, and simple models by coupling probabilistic inversion and Bayesian inversion. Here, we present a proof-of-concept study that uses probabilistic inversion to fuse a simple AIS model and diverse expert assessments. We demonstrate the ability of probabilistic inversion to infer joint prior probability distributions of model parameters that are consistent with expert assessments. We then confront these inferred expert priors with instrumental and paleoclimatic observational data in a Bayesian inversion. These additional constraints yield tighter hindcasts and projections. We use this approach to quantify how the deep uncertainty surrounding expert assessments affects the joint probability distributions of model parameters and future projections. PMID:29287095

NGNP Infrastructure Readiness Assessment: Consolidation Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brian K Castle

2011-02-01

The Next Generation Nuclear Plant (NGNP) project supports the development, demonstration, and deployment of high temperature gas-cooled reactors (HTGRs). The NGNP project is being reviewed by the Nuclear Energy Advisory Council (NEAC) to provide input to the DOE, who will make a recommendation to the Secretary of Energy, whether or not to continue with Phase 2 of the NGNP project. The NEAC review will be based on, in part, the infrastructure readiness assessment, which is an assessment of industry's current ability to provide specified components for the FOAK NGNP, meet quality assurance requirements, transport components, have the necessary workforce inmore » place, and have the necessary construction capabilities. AREVA and Westinghouse were contracted to perform independent assessments of industry's capabilities because of their experience with nuclear supply chains, which is a result of their experiences with the EPR and AP-1000 reactors. Both vendors produced infrastructure readiness assessment reports that identified key components and categorized these components into three groups based on their ability to be deployed in the FOAK plant. The NGNP project has several programs that are developing key components and capabilities. For these components, the NGNP project have provided input to properly assess the infrastructure readiness for these components.« less

Update on NASA Microelectronics Activities

NASA Technical Reports Server (NTRS)

Label, Kenneth A.; Sampson, Michael J.; Casey, Megan; Lauenstein, Jean-Marie

2017-01-01

Mission Statement: The NASA Electronic Parts and Packaging (NEPP) Program provides NASA's leadership for developing and maintaining guidance for the screening, qualification, test. and usage of EEE parts by NASA as well as in collaboration with other government Agencies and industry. NASA Space Technology Mission Directorate (STMD) "STMD rapidly develops, demonstrates, and infuses revolutionary, high-payoff technologies through transparent, collaborative partnerships, expanding the boundaries of the aerospace enterprise." Mission Statement: The Space Environments Testing Management Office (SETMO) will identify, prioritize, and manage a select suite of Agency key capabilities/assets that are deemed to be essential to the future needs of NASA or the nation, including some capabilities that lack an adequate business base over the budget horizon. NESC mission is to perform value-added independent testing, analysis, and assessments of NASA's high-risk projects to ensure safety and mission success. NASA Space Environments and Avionics Fellows as well as Radiation and EEE Parts Community of Practice (CoP) leads.

The Impact of Improved Oral Health on the Utilization of Dental Services.

PubMed

Eklund, Stephen A

2017-08-01

Since the mid-20th century, there has been a remarkable decline in dental caries in the United States. The effects of that caries decline have now been demonstrated well into the adult population. These improvements in oral health are resulting in substantial declines in the reparative and restorative dental services being provided to the affected individuals, who comprise a growing part of the population. Because of fewer compromised teeth, extractions and their sequelae also are declining. Much of the recall and periodontal maintenance care can be provided by allied dental personnel. As the older age cohorts, who were children before the caries decline occurred, become an ever-smaller part of the population, the number of patients an individual dentist can treat in a year is likely to increase. This article was written as part of the project "Advancing Dental Education in the 21 st Century."

Commercial Crew Development Environmental Control and Life Support System Status

NASA Technical Reports Server (NTRS)

Williams, David E.

2011-01-01

The National Aeronautics and Space Administration (NASA) Commercial Crew Development (CCDev) Project was a short term Project that was managed within the Commercial Crew and Cargo Program Office (C3PO) to help develop and demonstrate a small number of key human spaceflight capabilities in support of moving towards a possible commercial crew transportation system to low earth orbit (LEO). It was intended to foster entrepreneurial activities with a few selected companies. The other purpose of the Project was to try to reduce some of the possible risk with a commercial crew transportation system to LEO. The entrepreneurial activities were encouraged with these few selected companies by NASA providing only part of the total funding to complete specific tasks that were jointly agreed to by NASA and the company. These joint agreements were documented in a Space Act Agreement (SAA) that was signed by NASA and the company. This paper will provide an overview of the CCDev Project and it will also discuss in detail the Environmental Control and Life Support (ECLS) tasks that were performed under CCDev.

Recent Trend of New Type Power Delivery System and its Demonstrative Project in Japan

NASA Astrophysics Data System (ADS)

Morozumi, Satoshi; Nara, Koichi

Recently many such distributed generating systems as co-generation, photovoltaic, wind, fuel cells etc. are introduced into power distribution system, and the power system must cope with the situation with distributed generators. Moreover, such industries as IT request reliable and high quality power to preserve their businesses, and some other electric energy based industries request less reliable but cheaper electricity. From these backgrounds, several new type power delivery systems are emerging where lots of distributed generators (DGs) can be connected and many benefits offered by DGs can be realized without affecting the existing power system. They are referred to various names. In U.S.A., Microgrid, Power Park and Virtual Utilities, etc. are proposed. In Europe, DISPOWER or Smart Grid is under developing. In Japan, FRIENDS and Demand Area Network System etc. are proposed and tested in real sites. In this paper, first, general concepts of such new type power delivery systems and new businesses expected to be created by using DGs are introduced. Then, recent research activities in this area in Japan are introduced so as to stimulate new business opportunities. In the later part of this paper, related NEDO's demonstrative projects are introduced. NEDO is the largest public R&D management organization and promoting several projects regarding grid connecting issues on the power system. Those projects were planned to solve several problems on the power system where distributed renewable energy resources are installed.

Emergency School Aid Act, Pilot Project, 1975-76. Part I and Part II. Research and Evaluation Report, Vol. 10, No. 12.

ERIC Educational Resources Information Center

Crawley, Nora; Taylor, Myrtice

This paper describes and evaluates a pilot project funded under the Emergency School Aid Act (ESAA). The pilot project was subdivided into two parts: the Camp Learning Center program, and the Cultural Adjustment Program. Among the general goals of the Camp Learning Center were to improve mathematics and reading skills through a relevant and…

Rationale, design, and methods for process evaluation in the Childhood Obesity Research Demonstration project

USDA-ARS?s Scientific Manuscript database

The cross-site process evaluation plan for the Childhood Obesity Research Demonstration (CORD) project is described here. The CORD project comprises 3 unique demonstration projects designed to integrate multi-level, multi-setting health care and public health interventions over a 4-year funding peri...

Toward Elimination of Dog-Mediated Human Rabies: Experiences from Implementing a Large-scale Demonstration Project in Southern Tanzania

PubMed Central

Mpolya, Emmanuel Abraham; Lembo, Tiziana; Lushasi, Kennedy; Mancy, Rebecca; Mbunda, Eberhard M.; Makungu, Selemani; Maziku, Matthew; Sikana, Lwitiko; Jaswant, Gurdeep; Townsend, Sunny; Meslin, François-Xavier; Abela-Ridder, Bernadette; Ngeleja, Chanasa; Changalucha, Joel; Mtema, Zacharia; Sambo, Maganga; Mchau, Geofrey; Rysava, Kristyna; Nanai, Alphoncina; Kazwala, Rudovick; Cleaveland, Sarah; Hampson, Katie

2017-01-01

A Rabies Elimination Demonstration Project was implemented in Tanzania from 2010 through to 2015, bringing together government ministries from the health and veterinary sectors, the World Health Organization, and national and international research institutions. Detailed data on mass dog vaccination campaigns, bite exposures, use of post-exposure prophylaxis (PEP), and human rabies deaths were collected throughout the project duration and project areas. Despite no previous experience in dog vaccination within the project areas, district veterinary officers were able to implement district-wide vaccination campaigns that, for most part, progressively increased the numbers of dogs vaccinated with each phase of the project. Bite exposures declined, particularly in the southernmost districts with the smallest dog populations, and health workers successfully transitioned from primarily intramuscular administration of PEP to intradermal administration, resulting in major cost savings. However, even with improved PEP provision, vaccine shortages still occurred in some districts. In laboratory diagnosis, there were several logistical challenges in sample handling and submission but compared to the situation before the project started, there was a moderate increase in the number of laboratory samples submitted and tested for rabies in the project areas with a decrease in the proportion of rabies-positive samples over time. The project had a major impact on public health policy and practice with the formation of a One Health Coordination Unit at the Prime Minister’s Office and development of the Tanzania National Rabies Control Strategy, which lays a roadmap for elimination of rabies in Tanzania by 2030 by following the Stepwise Approach towards Rabies Elimination (SARE). Overall, the project generated many important lessons relevant to rabies prevention and control in particular and disease surveillance in general. Lessons include the need for (1) a specific unit in the government for managing disease surveillance; (2) application of innovative data collection and management approaches such as the use of mobile phones; (3) close cooperation and effective communication among all key sectors and stakeholders; and (4) flexible and adaptive programs that can incorporate new information to improve their delivery, and overcome challenges of logistics and procurement. PMID:28321400

Toward Elimination of Dog-Mediated Human Rabies: Experiences from Implementing a Large-scale Demonstration Project in Southern Tanzania.

PubMed

Mpolya, Emmanuel Abraham; Lembo, Tiziana; Lushasi, Kennedy; Mancy, Rebecca; Mbunda, Eberhard M; Makungu, Selemani; Maziku, Matthew; Sikana, Lwitiko; Jaswant, Gurdeep; Townsend, Sunny; Meslin, François-Xavier; Abela-Ridder, Bernadette; Ngeleja, Chanasa; Changalucha, Joel; Mtema, Zacharia; Sambo, Maganga; Mchau, Geofrey; Rysava, Kristyna; Nanai, Alphoncina; Kazwala, Rudovick; Cleaveland, Sarah; Hampson, Katie

2017-01-01

A Rabies Elimination Demonstration Project was implemented in Tanzania from 2010 through to 2015, bringing together government ministries from the health and veterinary sectors, the World Health Organization, and national and international research institutions. Detailed data on mass dog vaccination campaigns, bite exposures, use of post-exposure prophylaxis (PEP), and human rabies deaths were collected throughout the project duration and project areas. Despite no previous experience in dog vaccination within the project areas, district veterinary officers were able to implement district-wide vaccination campaigns that, for most part, progressively increased the numbers of dogs vaccinated with each phase of the project. Bite exposures declined, particularly in the southernmost districts with the smallest dog populations, and health workers successfully transitioned from primarily intramuscular administration of PEP to intradermal administration, resulting in major cost savings. However, even with improved PEP provision, vaccine shortages still occurred in some districts. In laboratory diagnosis, there were several logistical challenges in sample handling and submission but compared to the situation before the project started, there was a moderate increase in the number of laboratory samples submitted and tested for rabies in the project areas with a decrease in the proportion of rabies-positive samples over time. The project had a major impact on public health policy and practice with the formation of a One Health Coordination Unit at the Prime Minister's Office and development of the Tanzania National Rabies Control Strategy, which lays a roadmap for elimination of rabies in Tanzania by 2030 by following the Stepwise Approach towards Rabies Elimination (SARE). Overall, the project generated many important lessons relevant to rabies prevention and control in particular and disease surveillance in general. Lessons include the need for (1) a specific unit in the government for managing disease surveillance; (2) application of innovative data collection and management approaches such as the use of mobile phones; (3) close cooperation and effective communication among all key sectors and stakeholders; and (4) flexible and adaptive programs that can incorporate new information to improve their delivery, and overcome challenges of logistics and procurement.

[The LORAS Project and quality assurance. In four years from input- to outcome-oriented financing in public health. 1: The LORAS Project].

PubMed

Lenz, M J; Hochreutener, M A

2001-02-01

This series of three articles is a summary of the operations, findings and results of the hospital reform projects in the Canton of Zurich, termed LORAS. With the aid of the LORAS project within four years Zurich hospitals have been transformed. Whereas they used to adhere to input-oriented covering of deficits they now operate with outcome-oriented prospective financing of output. Part 1 describes the whole Project. Part 2 focuses on the development of outcome-measurement. Part 3 finally describes the implementation of the outcome-measurement in the canton of Zurich.

Golden Gate Vanpool Demonstration Project

DOT National Transportation Integrated Search

1979-07-01

The report evaluates the Golden Gate Vanpool Demonstration Project activities begun in October 1977. The objective of the demonstration is to successfuly promote commuter ridesharing through vanpools. The project grantee, the Golden Gate Bridge, High...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eudy, Leslie; Post, Matthew; Jeffers, Matthew

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB, which was developed as part of the Federal Transit Administration's (FTA) National Fuel Cell Bus Program, was delivered to SunLine in November 2011 and was put in revenue service in mid-December 2011. Two new AFCBs with an upgraded design were delivered in June/July of 2014 and a third new AFCB was delivered in February 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE)more » and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report covers the performance of the AFCBs from July 2015 through December 2016.« less

F-16XL Ship #2 during last flight showing titanium laminar flow glove on left wing

NASA Technical Reports Server (NTRS)

1996-01-01

The perforated titanium overlay mounted on the upper surface of the left wing is clearly evident on this view of NASA 848, a highly modified F-16XL aircraft flown by NASA's Dryden Flight Research Center in the Supersonic Laminar Flow Control (SLFC) research program. The two-seat, single-engine craft, one of only two 'XL' F-16s built, recently concluded the SLFC project with its 45th data collection mission. The project demonstrated that laminar--or smooth--airflow could be achieved over a major portion of a wing at supersonic speeds by use of a suction system. The system drew a small part of the boundary-layer air through millions of tiny laser-drilled holes in the 'glove' fitted to the upper left wing.

78 FR 16476 - Notice for Termination of a Disease Management Demonstration Project for TRICARE Standard...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-15

... Management Demonstration Project for TRICARE Standard Beneficiaries.'' The demonstration provided disease... DEPARTMENT OF DEFENSE Office of the Secretary Notice for Termination of a Disease Management Demonstration Project for TRICARE Standard Beneficiaries AGENCY: Office of the Secretary of Defense, (Health...

76 FR 80903 - Extension of Autism Services Demonstration Project for TRICARE Beneficiaries Under the Extended...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... DEPARTMENT OF DEFENSE Office of the Secretary Extension of Autism Services Demonstration Project... Enhanced Access to Autism Services Demonstration Project under the Extended Care Health Option for beneficiaries diagnosed with an Autism Spectrum Disorder (ASD). Under the demonstration, the Department...

78 FR 78342 - Extension of Autism Services Demonstration Project for TRICARE Beneficiaries Under the Extended...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-26

... DEPARTMENT OF DEFENSE Office of the Secretary Extension of Autism Services Demonstration Project... (the Department) Enhanced Access to Autism Services Demonstration Project (Autism Demonstration) under the Extended Care Health Option (ECHO) for beneficiaries diagnosed with an Autism Spectrum Disorder...

Space Station Furnace Facility. Volume 2: Requirements definition and conceptual design study

NASA Technical Reports Server (NTRS)

1992-01-01

The Space Station Freedom Furnace (SSFF) Project is divided into two phases: phase 1, a definition study phase, and phase 2, a design and development phase. TBE was awarded a research study entitled, 'Space Station Furnace Facility Requirements Definition and Conceptual Design Study' on June 2, 1989. This report addresses the definition study phase only. Phase 2 is to be complete after completion of phase 1. The contract encompassed a requirements definition study and culminated in hardware/facility conceptual designs and hardware demonstration development models to test these conceptual designs. The study was divided into two parts. Part 1 (the basic part of the effort) encompassed preliminary requirements definition and assessment; conceptional design of the SSFF Core; fabrication of mockups; and preparation for the support of a conceptional design review (CoDR). Part 2 (the optional part of the effort) included detailed definition of the engineering and design requirements, as derived from the science requirements; refinement of the conceptual design of the SSFF Core; fabrication and testing of the 'breadboards' or development models; and preparation for and support of a requirements definition review.

LILCO (Long Island Lighting Co. ) pushes electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daumann, E.; Dwing, A.H.

1979-02-01

Acting as manufacturer's representative, LILCO recently showed five new electric vehicles to over 75 major Long Island companies and organizations as part of a U.S. Department of Energy demonstration project. The five new models include three different types and sizes of vans and a pickup truck, all made by Jet Industries Inc., and a compact station wagon made by Electric Vehicle Associates Inc. All are capable of going faster and further than required by federal standards. E. Daumann, manager of LILCO's energy services department, explained that the vehicle batteries will usually be charged during the evening hours, when electricity costsmore » are lower and 40-50Vertical Bar3< of utility capacity nationwide is idle. LILCO plans to add 40 new electric vehicles to its present fleet of 12. Four other organizations selected by the Federal Government to be ''site operators'' for the demonstration project are American Telephone and Telegraph Co., Walt Disney World, Consolidated Edison Co. of New York Inc., and Penn Jersey Subaru. A. H. Dwing (Dep. Energy) said that the vehicles represent a means of conserving the world oil supplies.« less

Staunton 1 reclamation demonstration project. Aquatic ecosystems. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vinikour, W. S.

1981-02-01

To provide long-term indications of the potential water quality improvements following reclamation efforts at the Staunton 1 Reclamation Demonstration Project, macroinvertebrates were collected from three on-site ponds and from the receiving stream (Cahokia Creek) for site drainage. Implications for potential benthic community differences resulting from site runoff were disclosed, but macroinvertebrate diversity throughout Cahokia Creek was limited due to an unstable, sandy substrate. The three ponds sampled were the New Pond, which was created as part of the reclamation activities; the Shed Pond, which and the Old Pond, which, because it was an existing, nonimpacted pond free of site runoff,more » served as a control. Comparisons of macroinvertebrates from the ponds indicated the potential for the New Pond to develop into a productive ecosystem. Macroinvertebrates in the New Pond were generally species more tolerant of acid mine drainage conditions. However, due to the present limited faunal densities and the undesirable physical and chemical characteristics of the New Pond, the pond should not be stocked with fish at this time.« less

High-Temperature Thermochemical Storage with Redox-Stable Perovskites for Concentrating Solar Power, CRADA Number: CRD-14-554

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Zhiwen

As part of a Federal Opportunity Announcement (FOA) Award, the project will be led by Colorado School of Mines (CSM) to explore and demonstrate the efficacy of highly reducible, redox-stable oxides to provide efficient thermochemical energy storage for heat release at temperatures of 900 degrees Celcius or more. NREL will support the material development for its application in a concentrating solar power (CSP) plant. In the project, NREL will provide its inventive system design, chemical looping for CSP, and use it as a platform to accommodate the chemical processes using a cost effective perovskite materials identified by CSM. NREL willmore » design a 5-10kW particle receiver for perovskite reduction to store solar energy and help the development of a fluidized-bed reoxidation reactor and system integration. NREL will develop the demonstration receiver for on-sun test in the 5-10 kWt range in NREL's high flux solar furnace. NREL will assist in system analysis and provide techno-economic inputs for the overall system configuration.« less

5 CFR 470.301 - Program expectations.

Code of Federal Regulations, 2010 CFR

2010-01-01

....301 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PERSONNEL MANAGEMENT RESEARCH PROGRAMS AND DEMONSTRATIONS PROJECTS Regulatory Requirements Pertaining to Demonstration Projects § 470.301 Program expectations. (a) Demonstration projects permit the Office of Personnel...

75 FR 8927 - Autism Services Demonstration Project for TRICARE Beneficiaries Under the Extended Care Health...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-26

... DEPARTMENT OF DEFENSE Office of the Secretary Autism Services Demonstration Project for TRICARE... Access to Autism Services Demonstration Project under the Extended Care Health Option for beneficiaries diagnosed with an Autism Spectrum Disorder (ASD). Under the demonstration, the Department implemented a...

34 CFR 380.1 - What is the program of special projects and demonstrations for providing supported employment...

Code of Federal Regulations, 2012 CFR

2012-07-01

... demonstrations for providing supported employment services to individuals with the most severe disabilities and... employment services to individuals with the most severe disabilities, including projects that demonstrate the... SPECIAL PROJECTS AND DEMONSTRATIONS FOR PROVIDING SUPPORTED EMPLOYMENT SERVICES TO INDIVIDUALS WITH THE...

34 CFR 380.1 - What is the program of special projects and demonstrations for providing supported employment...

Code of Federal Regulations, 2011 CFR

2011-07-01

... demonstrations for providing supported employment services to individuals with the most severe disabilities and... employment services to individuals with the most severe disabilities, including projects that demonstrate the... SPECIAL PROJECTS AND DEMONSTRATIONS FOR PROVIDING SUPPORTED EMPLOYMENT SERVICES TO INDIVIDUALS WITH THE...

34 CFR 380.1 - What is the program of special projects and demonstrations for providing supported employment...

Code of Federal Regulations, 2013 CFR

2013-07-01

... demonstrations for providing supported employment services to individuals with the most severe disabilities and... employment services to individuals with the most severe disabilities, including projects that demonstrate the... SPECIAL PROJECTS AND DEMONSTRATIONS FOR PROVIDING SUPPORTED EMPLOYMENT SERVICES TO INDIVIDUALS WITH THE...

34 CFR 380.1 - What is the program of special projects and demonstrations for providing supported employment...

Code of Federal Regulations, 2014 CFR

2014-07-01

... demonstrations for providing supported employment services to individuals with the most severe disabilities and... employment services to individuals with the most severe disabilities, including projects that demonstrate the... SPECIAL PROJECTS AND DEMONSTRATIONS FOR PROVIDING SUPPORTED EMPLOYMENT SERVICES TO INDIVIDUALS WITH THE...

Using historical crash data as part of traffic work zone safety planning and project management strategies.

DOT National Transportation Integrated Search

2014-07-01

This funding enabled the project entitled, USING HISTORICAL CRASH DATA AS PART OF TRAFFIC WORK ZONE SAFETY : PLANNING AND PROJECT MANAGEMENT STRATEGIES to address the following: : Evaluate current organizational strategies with respect to w...

Understanding Wireless Communications in Public Safety: A Guidebook to Technology, Issues, Planning, and Management

DOT National Transportation Integrated Search

2000-08-01

This guidebook is divided into four parts: Part 1. Planning and Managing a Communications Project: Discusses the overall scope of a project, including planning, funding, procurement, and management. Part 2. Wireless Communications Technology: Discuss...

Visualizing the universe, part 2

NASA Technical Reports Server (NTRS)

Falco, Emilio E.; Kurtz, Michael J.; Bajuk, Mark

1992-01-01

It is now possible to create animated views of the universe that are realistic, physically relevant, and breathtaking. To demonstrate the point, we describe our efforts to navigate the CfA redshift survey. For our project, we selected several CCD images of spiral and elliptical galaxies, and placed them at their observed positions in redshift space. We demonstrate how, by choreographing aesthetically pleasing trajectories, we are able to develop our own and the viewer's intuition about the large-scale structures found in the CfA redshift survey. We show for instance that three-dimensional motion enhances significantly our perception of voids and sheets in the distribution of galaxies. Such sophistication happily has become possible with the 'coming of age' of observational cosmology, as data have grown to drive the field.

CSPonD demonstrative project: Start-up process of a 25 kW prototype

NASA Astrophysics Data System (ADS)

Gil, Antoni; Grange, Benjamin; Perez, Victor G.; Tetreault-Friend, Melanie; Codd, Daniel S.; Calvet, Nicolas; Slocum, Alexander S.

2017-06-01

The current concept of commercial concentrated solar power (CSP) plants, based on the concept of a solar field, receiver, storage and power block, experienced significant growth in the past decades. The power block is the most well know part of the plant, while solar field depends on the receiver technology. The dominant receiver technologies are parabolic troughs and central towers. Most thermal energy storage (TES) relies on two tanks of molten salts, one hot and one cold serviced by pumps and piping systems. In spite of the technical development level achieved by these systems, efficiency is limited, mainly caused by thermal losses in piping, parasitic losses due to electric tracing and pumping and receiver limitations. In order to mitigate the these issues, a new concept called Concentrated Solar Power on Demand (CSPonD), was developed, consisting of a direct absorption Solar Salt CSP receiver which simultaneously acts as TES tank. Currently, in the frame of the flagship collaborative project between the Masdar Institute (UAE) and the Massachusetts Institute of Technology (USA) a 25 kW demonstrative prototype is in its final building phase at the Masdar Institute Solar Platform. The present paper, explains the demonstration prototype based on the CSPonD concept, with emphasis on the planned start-up process for the facility.

Climate change impact assessment on flow regime by incorporating spatial correlation and scenario uncertainty

NASA Astrophysics Data System (ADS)

Vallam, P.; Qin, X. S.

2017-07-01

Flooding risk is increasing in many parts of the world and may worsen under climate change conditions. The accuracy of predicting flooding risk relies on reasonable projection of meteorological data (especially rainfall) at the local scale. The current statistical downscaling approaches face the difficulty of projecting multi-site climate information for future conditions while conserving spatial information. This study presents a combined Long Ashton Research Station Weather Generator (LARS-WG) stochastic weather generator and multi-site rainfall simulator RainSim (CLWRS) approach to investigate flow regimes under future conditions in the Kootenay Watershed, Canada. To understand the uncertainty effect stemming from different scenarios, the climate output is fed into a hydrologic model. The results showed different variation trends of annual peak flows (in 2080-2099) based on different climate change scenarios and demonstrated that the hydrological impact would be driven by the interaction between snowmelt and peak flows. The proposed CLWRS approach is useful where there is a need for projection of potential climate change scenarios.

KSC-2009-6456

NASA Image and Video Library

2009-11-19

CAPE CANAVERAL, Fla. – At NASA's Kennedy Space Center in Florida, Kennedy Director Bob Cabana, left, congratulates, Eric Silagy, Florida Power & Light Company vice president and chief development officer, for his part in the construction of NASA's first large-scale solar power generation facility as Roderick Roche, senior manager, Project Management Office of North America, SunPower Corporation, looks on. Representatives from NASA, Florida Power & Light Company, or FPL, and SunPower Corporation formally commissioned the one-megawatt facility and announced plans to pursue a new research, development and demonstration project at Kennedy to advance America's use of renewable energy. The facility is the first element of a major renewable energy project currently under construction at Kennedy. The completed system features a fixed-tilt, ground-mounted solar power system designed and built by SunPower, along with SunPower solar panels. A 10-megawatt solar farm, which SunPower is building on nearby Kennedy property, will supply power to FPL's customers when it is completed in April 2010. Photo credit: NASA/Jim Grossmann

KSC-2009-6455

NASA Image and Video Library

2009-11-19

CAPE CANAVERAL, Fla. – At NASA's Kennedy Space Center in Florida, Kennedy Director Bob Cabana, left, congratulates Roderick Roche, senior manager, Project Management Office of North America, SunPower Corporation, for his part in the construction of NASA's first large-scale solar power generation facility as Eric Silagy, Florida Power & Light Company vice president and chief development officer, looks on. Representatives from NASA, Florida Power & Light Company, or FPL, and SunPower Corporation formally commissioned the one-megawatt facility and announced plans to pursue a new research, development and demonstration project at Kennedy to advance America's use of renewable energy. The facility is the first element of a major renewable energy project currently under construction at Kennedy. The completed system features a fixed-tilt, ground-mounted solar power system designed and built by SunPower, along with SunPower solar panels. A 10-megawatt solar farm, which SunPower is building on nearby Kennedy property, will supply power to FPL's customers when it is completed in April 2010. Photo credit: NASA/Jim Grossmann

A systems approach to computer-based training

NASA Technical Reports Server (NTRS)

Drape, Gaylen W.

1994-01-01

This paper describes the hardware and software systems approach used in the Automated Recertification Training System (ARTS), a Phase 2 Small Business Innovation Research (SBIR) project for NASA Kennedy Space Center (KSC). The goal of this project is to optimize recertification training of technicians who process the Space Shuttle before launch by providing computer-based training courseware. The objectives of ARTS are to implement more effective CBT applications identified through a need assessment process and to provide an ehanced courseware production system. The system's capabilities are demonstrated by using five different pilot applications to convert existing classroom courses into interactive courseware. When the system is fully implemented at NASA/KSC, trainee job performance will improve and the cost of courseware development will be lower. Commercialization of the technology developed as part of this SBIR project is planned for Phase 3. Anticipated spin-off products include custom courseware for technical skills training and courseware production software for use by corporate training organizations of aerospace and other industrial companies.

A retrospective view of the quality of the fauna component of the Olympic Dam Project Environmental Impact Statement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Read, J.L.

1994-06-01

The merits of the fauna section of the Olympic Dam Project Environmental Impact Statement (EIS) are discussed. The values of different survey methods and monitoring organisms used in this document are evaluated following 10 years of fauna monitoring and research subsequent to the preparation of the EIS. The pilot fauna reconnaissance was found to be of little value, although the associated literature review formed an integral part of the EIS. Over 95% of all amphibian, reptile and bird species recorded at Olympic Dam were confirmed or predicted to occur in the EIS. Mammal predictions were less accurate because of themore » sparse populations and irruptive nature of several arid-zone species. Prediction and monitoring of rare species were demonstrably difficult. The Olympic Dam Project EIS was found in general to be an accurate and useful document. However, it is suggested that more emphasis be placed on establishing monitoring programmes for future EISs, particularly for invertebrates. 35 refs., 1 fig., 3 tabs.« less

Engaging patients as partners in health research: Lessons from BC, Canada.

PubMed

Holmes, Bev J; Bryan, Stirling; Ho, Kendall; McGavin, Colleen

2018-03-01

Canada is seeing increased interest in engaging patients in health research, recognizing the potential to improve its relevance and quality. The momentum is promising, but there may be a tendency to ignore the challenges inherent when lay people and professionals collaborate. We address some of these challenges as they relate to recruitment, training, and support for patients at the British Columbia (BC) Support for People and Patient-Oriented Research Unit, part of Canada's Strategy for Patient-Oriented Research. A retrospective review of a telehealth project demonstrates that, as well as the practical elements of recruitment, training, and support, attention must be paid to issues of credibility, legitimacy, and power when engaging patients. We propose that all patient-oriented research projects would benefit from using a similar framework to guide patient engagement planning and implementation, helping to anticipate and mitigate challenges from the outset. Projects would ideally also include the study of patient engagement methods, to add to this important body of knowledge.

Progress along developmental tracks for electronic health records implementation in the United States

PubMed Central

Hollar, David W

2009-01-01

The development and implementation of electronic health records (EHR) have occurred slowly in the United States. To date, these approaches have, for the most part, followed four developmental tracks: (a) Enhancement of immunization registries and linkage with other health records to produce Child Health Profiles (CHP), (b) Regional Health Information Organization (RHIO) demonstration projects to link together patient medical records, (c) Insurance company projects linked to ICD-9 codes and patient records for cost-benefit assessments, and (d) Consortia of EHR developers collaborating to model systems requirements and standards for data linkage. Until recently, these separate efforts have been conducted in the very silos that they had intended to eliminate, and there is still considerable debate concerning health professionals access to as well as commitment to using EHR if these systems are provided. This paper will describe these four developmental tracks, patient rights and the legal environment for EHR, international comparisons, and future projections for EHR expansion across health networks in the United States. PMID:19291284

A demonstration of the instream flow incremental methodology, Shenandoah River

USGS Publications Warehouse

Zappia, Humbert; Hayes, Donald C.

1998-01-01

Current and projected demands on the water resources of the Shenandoah River have increased concerns for the potential effect of these demands on the natural integrity of the Shenandoah River system. The Instream Flow Incremental Method (IFIM) process attempts to integrate concepts of water-supply planning, analytical hydraulic engineering models, and empirically derived habitat versus flow functions to address water-use and instream-flow issues and questions concerning life-stage specific effects on selected species and the general well being of aquatic biological populations.The demonstration project also sets the stage for the identification and compilation of the major instream-flow issues in the Shenandoah River Basin, development of the required multidisciplinary technical team to conduct more detailed studies, and development of basin specific habitat and flow requirements for fish species, species assemblages, and various water uses in the Shenandoah River Basin. This report presents the results of an IFIM demonstration project, conducted on the main stem Shenandoah River in Virginia, during 1996 and 1997, using the Physical Habitat Simulation System (PHABSIM) model.Output from PHABSIM is used to address the general flow requirements for water supply and recreation and habitat for selected life stages of several fish species. The model output is only a small part of the information necessary for effective decision making and management of river resources. The information by itself is usually insufficient for formulation of recommendations regarding instream-flow requirements. Additional information, for example, can be obtained by analysis of habitat time-series data, habitat duration data, and habitat bottlenecks. Alternative-flow analysis and habitat-duration curves are presented.

Increased oil production and reserves from improved completion techniques in the Bluebell field, Uinta Basin. Quarterly technical report, October 1, 1996--December 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, C.D.

1997-02-01

The objective of this project is to increase oil production and reserves in the Uinta Basin by demonstrating improved completion techniques. Low productivity of Uinta Basin wells is caused by gross production intervals of several thousand feet that contain perforated thief zones, water-bearing zones, and unperforated oil-bearing intervals. Geologic and engineering characterization and computer simulation of the Green River and Wasatch formations in the Bluebell field will determine reservoir heterogeneities related to fractures and depositional trends. This will be followed by drilling and recompletion of several wells to demonstrate improved completion techniques based on the reservoir characterization. Transfer of themore » project results will be an ongoing component of the project. The recompletion of the Michelle Ute 7-1 well commenced and is the first step in the three-well demonstration. As part of the recompletion, the gross productive interval was logged, additional beds were perforated, and the entire interval was stimulated with a three-stage acid treatment. The operator attempted to stimulate the well at high pressure (about 10,000 pounds per square inch (psi) [68,950 kPa]) at three separate packer locations. But at each location the pressure would not hold. As a result, all three stages were pumped at a lower pressure (6500 psi maximum [44,820 kPa]) from one packer location. As of December 31, 1996, the operator was tripping in the hole with the production packer and tubing to begin swab testing the well.« less

5 CFR 890.1303 - Eligibility.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL... Demonstration Project § 890.1303 Eligibility. (a) To enroll in the demonstration project, an individual must... benefit plans offered through the FEHB Program under the demonstration project. (d) When determining...