The intact capture of hypervelocity dust particles using underdense foams

NASA Technical Reports Server (NTRS)

Maag, Carl R.; Borg, J.; Tanner, William G.; Stevenson, T. J.; Bibring, J.-P.

1994-01-01

The impact of a hypervelocity projectile (greater than 3 km/s) is a process that subjects both the impactor and the impacted material to a large transient pressure distribution. The resultant stresses cause a large degree of fragmentation, melting, vaporization, and ionization (for normal densities). The pressure regime magnitude, however, is directly related to the density relationship between the projectile and target materials. As a consequence, a high-density impactor on a low-density target will experience the lowest level of damage. Historically, there have been three different approaches toward achieving the lowest possible target density. The first employs a projectile impinging on a foil or film of moderate density, but whose thickness is much less than the particle diameter. This results in the particle experiencing a pressure transient with both a short duration and a greatly reduced destructive effect. A succession of these films, spaced to allow nondestructive energy dissipation between impacts, will reduce the impactor's kinetic energy without allowing its internal energy to rise to the point where destruction of the projectile mass will occur. An added advantage to this method is that it yields the possibility of regions within the captured particle where a minimum of thermal modification has taken place. Polymer foams have been employed as the primary method of capturing particles with minimum degradation. The manufacture of extremely low bulk density materials is usually achieved by the introduction of voids into the material base. It must be noted, however, that a foam structure only has a true bulk density of the mixture at sizes much larger than the cell size, since for impact processes this is of paramount importance. The scale at which the bulk density must still be close to that of the mixture is approximately equal to the impactor. When this density criterion is met, shock pressures during impact are minimized, which in turn maximizes the probability of survival for the impacting particle. The primary objectives of the experiment are to (1) Examine the morphology of primary and secondary hypervelocity impact craters. Primary attention will be paid to craters caused by ejecta during hypervelocity impacts of different substrates. (2) Determine the size distribution of ejecta by means of witness plates and collect fragments of ejecta from craters by means of momentum-sensitive mcropore foam. (3) Assess the directionality of the flux by means of penetration-hole alignment of thin films placed above the cells. (4) Capture intact the particles that perforated the thin film and entered the cell. Capture media consisted of both previously flight-tested micropore foams and aerogel. The foams had different latent heats of fusion and, accordingly, will capture particles over a range of momenta. Aerogel was incorporated into the cells to determine the minimum diameter than can be captured intact.

Impact of Computer-Aided CT and PET Analysis on Non-invasive T Staging in Patients with Lung Cancer and Atelectasis.

PubMed

Flechsig, Paul; Rastgoo, Ramin; Kratochwil, Clemens; Martin, Ole; Holland-Letz, Tim; Harms, Alexander; Kauczor, Hans-Ulrich; Haberkorn, Uwe; Giesel, Frederik L

2018-04-20

Tumor delineation within an atelectasis in lung cancer patients is not always accurate. When T staging is done by integrated 2-deoxy-2-[ 18 F]fluoro-D-glucose ([ 18 F]FDG)-positron emission tomography (PET)/X-ray computer tomography (CT), tumors of neuroendocrine differentiation and slowly growing tumors can present with reduced FDG uptake, thus aggravating an exact T staging. In order to further exhaust information derived from [ 18 F]FDG-PET/CT, we evaluated the impact of CT density and maximum standardized uptake value (SUVmax) for the classification of different tumor subtypes within a surrounding atelectasis, as well as possible cutoff values for the differentiation between the primary tumor and atelectatic lung tissue. Seventy-two patients with histologically proven lung cancer and adjacent atelectasis were investigated. Non-contrast-enhanced [ 18 F]FDG-PET/CT was performed within 2 weeks before surgery/biopsy. Boundaries of the primary within the atelectasis were determined visually on the basis of [ 18 F]FDG uptake; CT density was quantified manually within each primary and each atelectasis. CT density of the primary (36.4 Hounsfield units (HU) ± 6.2) was significantly higher compared to that of atelectatic lung (24.3 HU ± 8.3; p < 0.01), irrespective of the histological subtype. The discrimination between different malignant tumors using density analysis failed. SUVmax was increased in squamous cell carcinomas compared to adenocarcinomas. Irrespective of the malignant subtype, a possible cutoff value of 24 HU may help to exclude the presence of a primary in lesions below 24 HU, whereas a density above a threshold of 40 HU can help to exclude atelectatic lung. Density measurements in patients with lung cancer and surrounding atelectasis may help to delineate the primary tumor, irrespective of the specific lung cancer subtype. This could improve T staging and radiation treatment planning (RTP) without additional application of a contrast agent in CT, or an additional magnetic resonance imaging (MRI), even in cases of lung tumors of neuroendocrine differentiation or in slowly growing tumors with less avidity to [ 18 F]FDG.

Evaluation of TransTech joint maker and precompaction screed.

DOT National Transportation Integrated Search

2000-09-01

The primary objective of this evaluation is to determine the effectiveness of the Joint Maker and Precompaction : Screed, both developed by TransTech Systems, Inc., in achieving higher and more uniform density across the mat of : a rehabilitated Hot ...

Baseline Testing of Ultracapacitors for the Next Generation Launch Technology (NGLT) Project. Revised

NASA Technical Reports Server (NTRS)

Eichenberg, Dennis J.

2005-01-01

The NASA John H. Glenn Research Center initiated baseline testing of ultracapacitors for the Next Generation Launch Transportation (NGLT) project to obtain empirical data for determining the feasibility of using ultracapacitors for the project. There are large transient loads associated with NGLT that require either a very large primary energy source or an energy storage system. The primary power source used for these tests is a proton exchange membrane (PEM) fuel cell. The energy storage system can consist of devices such as batteries, flywheels, or ultracapacitors. Ultracapacitors were used for these tests. Ultracapacitors are ideal for applications such as NGLT where long life, maintenance-free operation, and excellent low-temperature performance is essential. State-of-the-art symmetric ultracapacitors were used for these tests. The ultracapacitors were interconnected in an innovative configuration to minimize interconnection impedance. PEM fuel cells provide excellent energy density, but not good power density. Ultracapacitors provide excellent power density, but not good energy density. The combination of PEM fuel cells and ultracapacitors provides a power source with excellent energy density and power density. The life of PEM fuel cells is shortened significantly by large transient loads. Ultracapacitors used in conjunction with PEM fuel cells reduce the transient loads applied to the fuel cell, and thus appreciably improves its life. PEM fuel cells were tested with and without ultracapacitors, to determine the benefits of ultracapacitors. The report concludes that the implementation of symmetric ultracapacitors in the NGLT power system can provide significant improvements in power system performance and reliability.

Baseline Testing of Ultracapacitors for the Next Generation Launch Technology (NGLT) Project

NASA Technical Reports Server (NTRS)

Eichenberg, Dennis J.

2004-01-01

The NASA John H. Glenn Research Center initiated baseline testing of ultracapacitors for the Next Generation Launch Transportation (NGLT) project to obtain empirical data for determining the feasibility of using ultracapacitors for the project. There are large transient loads associated with NGLT that require either a very large primary energy source or an energy storage system. The primary power source used for these tests is a proton exchange membrane (PEM) fuel cell. The energy storage system can consist of devices such as batteries, flywheels, or ultracapacitors. Ultracapacitors were used for these tests. Ultracapacitors are ideal for applications such as NGLT where long life, maintenance-free operation, and excellent low-temperature performance is essential. State-of-the-art symmetric ultracapacitors were used for these tests. The ultracapacitors were interconnected in an innovative configuration to minimize interconnection impedance. PEM fuel cells provide excellent energy density, but not good power density. Ultracapacitors provide excellent power density, but not good energy density. The combination of PEM fuel cells and ultracapacitors provides a power source with excellent energy density and power density. The life of PEM fuel cells is shortened significantly by large transient loads. Ultracapacitors used in conjunction with PEM fuel cells reduce the transient loads applied to the fuel cell, and thus appreciably improves its life. PEM fuel cells were tested with and without ultracapacitors, to determine the benefits of ultracapacitors. The report concludes that the implementation of symmetric ultracapacitors in the NGLT power system can provide significant improvements in power system performance and reliability.

[Comparative analysis of the susceptibility and productivity of respiratory tract target cells of mice and rats exposed to inflienza virus in vitro].

PubMed

Zhukov, V A; Shishkina, L N; Sergeev, A A; Malkova, E M; Riabchikova, E I; Petrishchenko, V A; Sergeev, A N; Ustiuzhanina, N V; Nesvizhskiĭ, Iu V; Vorob'ev, A A

2008-01-01

The levels of susceptibility to influenza virus A/Aichi/2/68 H3N2 and the virus yield were determined using primary cells of the trachea and lungs of CD-1 mice and Wistar rats, and for 3 sets of cells obtained from primary lung cells of the both species by centrifugation in the gradient of density and by sedimentation on a surface. The values of ID50 virus dose for 10(6) cells and virus yield per 1 infected cell determined for primary mice cells were 4.0+/-0.47 and 3.2+/-0.27 IgEID50 (lung cells), 3.8+/-0.17 and 3.3+/-0.20 IgEID50 (tracheal cells), and those determined for primary rat cells were 4.0+/-0.35 and 2.1+/-0.24 IgEID50 (lung cells), 3.7+/-0.27 and 2.2+/-0.46 IgEID50 (tracheal cells). The values of ID50 and yield measured for mixtures of cells obtained from primary lung cells by centrifugation in gradient of density and by sedimentation on a surface differed insignificantly (p = 0.05) from the values of the corresponding parameters measured for lung and tracheal cells for both rats and mice. The analysis of data on the variation of the concentrations of different cell types in the experimental cell mixtures shows that type 1 and 2 alveolocytes possess significantly lower (p = 0.05) susceptibility and productivity vs. ciliated cells of the both species. The investigation was conducted within the frame of the ISTC/DARPA#450p project.

An Intraoperative Site-specific Bone Density Device: A Pilot Test Case.

PubMed

Arosio, Paolo; Moschioni, Monica; Banfi, Luca Maria; Di Stefano, Anilo Alessio

2015-08-01

This paper reports a case of all-on-four rehabilitation where bone density at implant sites was assessed both through preoperative computed tomographic (CT) scans and using a micromotor working as an intraoperative bone density measurement device. Implant-supported rehabilitation is a predictable treatment option for tooth replacement whose success depends on the clinician's experience, the implant characteristics and location and patient-related factors. Among the latter, bone density is a determinant for the achievement of primary implant stability and, eventually, for implant success. The ability to measure bone density at the placement site before implant insertion could be important in the clinical setting. A patient complaining of masticatory impairment was presented with a plan calling for extraction of all her compromised teeth, followed by implant rehabilitation. A week before surgery, she underwent CT examination, and the bone density on the CT scans was measured. When the implant osteotomies were created, the bone density was again measured with a micromotor endowed with an instantaneous torque-measuring system. The implant placement protocols were adapted for each implant, according to the intraoperative measurements, and the patient was rehabilitated following an all-on-four immediate loading protocol. The bone density device provided valuable information beyond that obtained from CT scans, allowing for site-specific, intraoperative assessment of bone density immediately before implant placement and an estimation of primary stability just after implant insertion. Measuring jaw-bone density could help clinicians to select implant-placement protocols and loading strategies based on site-specific bone features.

Mass-Mobility Characterization of Flame-made ZrO2 Aerosols: Primary Particle Diameter & Extent of Aggregation

PubMed Central

Eggersdorfer, M.L.; Gröhn, A.J.; Sorensen, C.M.; McMurry, P.H.; Pratsinis, S.E.

2013-01-01

Gas-borne nanoparticles undergoing coagulation and sintering form irregular or fractal-like structures affecting their transport, light scattering, effective surface area and density. Here, zirconia (ZrO2) nanoparticles are generated by scalable spray combustion, and their mobility diameter and mass are obtained nearly in-situ by differential mobility analyzer (DMA) and aerosol particle mass (APM) measurements. Using these data, the density of ZrO2 and a power law between mobility and primary particle diameters, the structure of fractal-like particles is determined (mass-mobility exponent, prefactor and average number and surface area mean diameter of primary particles, dva). The dva determined by DMA-APM measurements and this power law is in good agreement with the dva obtained by ex-situ nitrogen adsorption and microscopic analysis. Using this combination of measurements and above power law, the effect of flame spray process parameters (e.g. precursor solution and oxygen flow rate as well as zirconium concentration) on fractal-like particle structure characteristics is investigated in detail. This reveals that predominantly agglomerates (physically-bonded particles) and aggregates (chemically- or sinter-bonded particles) of nanoparticles are formed at low and high particle concentrations, respectively. PMID:22959835

Calcaneal bone mineral density and mechanical strength of the metatarsals.

PubMed

Lidtke, R H; Patel, D; Muehleman, C

2000-10-01

The primary aim of this study was to determine the predictive value of the bone mineral density of the calcaneus for fracture of the metatarsals. The authors report a strong positive correlation between the bone mineral density of the calcaneus and the four-point bending strength of each of the five metatarsals (r2 = 0.76, 0.64, 0.70, 0.68, and 0.78 for metatarsals 1 through 5, respectively). In addition, the relative strengths of the metatarsals and the correlation with their in vivo loads during gait as previously reported in the literature are discussed.

Integrated Cryptosporidium Assay To Determine Oocyst Density, Infectivity, and Genotype for Risk Assessment of Source and Reuse Water

PubMed Central

King, Brendon; Fanok, Stella; Phillips, Renae; Swaffer, Brooke

2015-01-01

Cryptosporidium continues to be problematic for the water industry, with risk assessments often indicating that treatment barriers may fail under extreme conditions. However, risk analyses have historically used oocyst densities and not considered either oocyst infectivity or species/genotype, which can result in an overestimation of risk if the oocysts are not human infective. We describe an integrated assay for determining oocyst density, infectivity, and genotype from a single-sample concentrate, an important advance that overcomes the need for processing multiple-grab samples or splitting sample concentrates for separate analyses. The assay incorporates an oocyst recovery control and is compatible with standard primary concentration techniques. Oocysts were purified from primary concentrates using immunomagnetic separation prior to processing by an infectivity assay. Plate-based cell culture was used to detect infectious foci, with a monolayer washing protocol developed to allow recovery and enumeration of oocysts. A simple DNA extraction protocol was developed to allow typing of any wells containing infectious Cryptosporidium. Water samples from a variety of source water and wastewater matrices, including a semirural catchment, wastewater, an aquifer recharge site, and storm water, were analyzed using the assay. Results demonstrate that the assay can reliably determine oocyst densities, infectivity, and genotype from single-grab samples for a variety of water matrices and emphasize the varying nature of Cryptosporidium risk extant throughout source waters and wastewaters. This assay should therefore enable a more comprehensive understanding of Cryptosporidium risk for different water sources, assisting in the selection of appropriate risk mitigation measures. PMID:25769833

Integrated cryptosporidium assay to determine oocyst density, infectivity, and genotype for risk assessment of source and reuse water.

PubMed

King, Brendon; Fanok, Stella; Phillips, Renae; Swaffer, Brooke; Monis, Paul

2015-05-15

Cryptosporidium continues to be problematic for the water industry, with risk assessments often indicating that treatment barriers may fail under extreme conditions. However, risk analyses have historically used oocyst densities and not considered either oocyst infectivity or species/genotype, which can result in an overestimation of risk if the oocysts are not human infective. We describe an integrated assay for determining oocyst density, infectivity, and genotype from a single-sample concentrate, an important advance that overcomes the need for processing multiple-grab samples or splitting sample concentrates for separate analyses. The assay incorporates an oocyst recovery control and is compatible with standard primary concentration techniques. Oocysts were purified from primary concentrates using immunomagnetic separation prior to processing by an infectivity assay. Plate-based cell culture was used to detect infectious foci, with a monolayer washing protocol developed to allow recovery and enumeration of oocysts. A simple DNA extraction protocol was developed to allow typing of any wells containing infectious Cryptosporidium. Water samples from a variety of source water and wastewater matrices, including a semirural catchment, wastewater, an aquifer recharge site, and storm water, were analyzed using the assay. Results demonstrate that the assay can reliably determine oocyst densities, infectivity, and genotype from single-grab samples for a variety of water matrices and emphasize the varying nature of Cryptosporidium risk extant throughout source waters and wastewaters. This assay should therefore enable a more comprehensive understanding of Cryptosporidium risk for different water sources, assisting in the selection of appropriate risk mitigation measures. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Further developments in orbit ephemeris derived neutral density

NASA Astrophysics Data System (ADS)

Locke, Travis

There are a number of non-conservative forces acting on a satellite in low Earth orbit. The one which is the most dominant and also contains the most uncertainty is atmospheric drag. Atmospheric drag is directly proportional to atmospheric density, and the existing atmospheric density models do not accurately model the variations in atmospheric density. In this research, precision orbit ephemerides (POE) are used as input measurements in an optimal orbit determination scheme in order to estimate corrections to existing atmospheric density models. These estimated corrections improve the estimates of the drag experienced by a satellite and therefore provide an improvement in orbit determination and prediction as well as a better overall understanding of the Earth's upper atmosphere. The optimal orbit determination scheme used in this work includes using POE data as measurements in a sequential filter/smoother process using the Orbit Determination Tool Kit (ODTK) software. The POE derived density estimates are validated by comparing them with the densities derived from accelerometers on board the Challenging Minisatellite Payload (CHAMP) and the Gravity Recovery and Climate Experiment (GRACE). These accelerometer derived density data sets for both CHAMP and GRACE are available from Sean Bruinsma of the Centre National d'Etudes Spatiales (CNES). The trend in the variation of atmospheric density is compared quantitatively by calculating the cross correlation (CC) between the POE derived density values and the accelerometer derived density values while the magnitudes of the two data sets are compared by calculating the root mean square (RMS) values between the two. There are certain high frequency density variations that are observed in the accelerometer derived density data but not in the POE derived density data or any of the baseline density models. These high frequency density variations are typically small in magnitude compared to the overall day-night variation. However during certain time periods, such as when the satellite is near the terminator, the variations are on the same order of magnitude as the diurnal variations. These variations can also be especially prevalent during geomagnetic storms and near the polar cusps. One of the goals of this work is to see what affect these unmodeled high frequency variations have on orbit propagation. In order to see this effect, the orbits of CHAMP and GRACE are propagated during certain time periods using different sources of density data as input measurements (accelerometer, POE, HASDM, and Jacchia 1971). The resulting orbit propagations are all compared to the propagation using the accelerometer derived density data which is used as truth. The RMS and the maximum difference between the different propagations are analyzed in order to see what effect the unmodeled density variations have on orbit propagation. These results are also binned by solar and geomagnetic activity level. The primary input into the orbit determination scheme used to produce the POE derived density estimates is a precision orbit ephemeris file. This file contains position and velocity in-formation for the satellite based on GPS and SLR measurements. The values contained in these files are estimated values and therefore contain some level of error, typically thought to be around the 5-10 cm level. The other primary focus of this work is to evaluate the effect of adding different levels of noise (0.1 m, 0.5 m, 1 m, 10 m, and 100 m) to this raw ephemeris data file before it is input into the orbit determination scheme. The resulting POE derived density estimates for each level of noise are then compared with the accelerometer derived densities by computing the CC and RMS values between the data sets. These results are also binned by solar and geomagnetic activity level.

Automatic photointerpretation for land use management in Minnesota

NASA Technical Reports Server (NTRS)

Swanlund, G. D. (Principal Investigator); Pile, D. R.

1973-01-01

The author has identified the following significant results. Primary conclusions from the lake acreage study are: (1) The ERTS-1 band 7 density range of 0-5 reliably indicates open water down to 2 acre size. (2) The density range 6-9 identifies swamps. (3) The depth of the water could not be determined. (4) Cloud shadows can be misread as lakes unless the clouds are detected. (5) ERTS-1 data would provide the information for classifying lakes and for monitoring fluctuations in lake area.

Long-term culture of rat hippocampal neurons at low density in serum-free medium: combination of the sandwich culture technique with the three-dimensional nanofibrous hydrogel PuraMatrix.

PubMed

Kaneko, Ai; Sankai, Yoshiyuki

2014-01-01

The primary culture of neuronal cells plays an important role in neuroscience. There has long been a need for methods enabling the long-term culture of primary neurons at low density, in defined serum-free medium. However, the lower the cell density, the more difficult it is to maintain the cells in culture. Therefore, we aimed to develop a method for long-term culture of neurons at low density, in serum-free medium, without the need for a glial feeder layer. Here, we describe the work leading to our determination of a protocol for long-term (>2 months) primary culture of rat hippocampal neurons in serum-free medium at the low density of 3×10(4) cells/mL (8.9×10(3) cells/cm2) without a glial feeder layer. Neurons were cultured on a three-dimensional nanofibrous hydrogel, PuraMatrix, and sandwiched under a coverslip to reproduce the in vivo environment, including the three-dimensional extracellular matrix, low-oxygen conditions, and exposure to concentrated paracrine factors. We examined the effects of varying PuraMatrix concentrations, the timing and presence or absence of a coverslip, the timing of neuronal isolation from embryos, cell density at plating, medium components, and changing the medium or not on parameters such as developmental pattern, cell viability, neuronal ratio, and neurite length. Using our method of combining the sandwich culture technique with PuraMatrix in Neurobasal medium/B27/L-glutamine for primary neuron culture, we achieved longer neurites (≥3,000 µm), greater cell viability (≥30%) for 2 months, and uniform culture across the wells. We also achieved an average neuronal ratio of 97%, showing a nearly pure culture of neurons without astrocytes. Our method is considerably better than techniques for the primary culture of neurons, and eliminates the need for a glial feeder layer. It also exhibits continued support for axonal elongation and synaptic activity for long periods (>6 weeks).

Impact of the California breast density law on primary care physicians.

PubMed

Khong, Kathleen A; Hargreaves, Jonathan; Aminololama-Shakeri, Shadi; Lindfors, Karen K

2015-03-01

To investigate primary physician awareness of the California Breast Density Notification Law and its impact on primary care practice. An online survey was distributed to 174 physicians within a single primary care network system 10 months after California's breast density notification law took effect. The survey assessed physicians' awareness of the law, perceived changes in patient levels of concern about breast density, and physician comfort levels in handling breast density management issues. The survey was completed by 77 physicians (45%). Roughly half of those surveyed (49%) reported no knowledge of the breast density notification legislation. Only 32% of respondents noted an increase in patient levels of concern about breast density compared to prior years. The majority were only "somewhat comfortable" (55%) or "not comfortable" (12%) with breast density questions, and almost one-third (32%) had referred patients to a breast health clinic for these discussions. A total of 75% of those surveyed would be interested in more specific education on the subject. Awareness among primary care clinicians of the California Breast Density Notification Law is low, and many do not feel comfortable answering breast density-related patient questions. Breast imagers and institutions may need to devote additional time and resources to primary physician education in order for density notification laws to have significant impact on patient care. Copyright © 2015 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Analytic solution of the Spencer-Lewis angular-spatial moments equations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Filippone, W.L.

A closed-form solution for the angular-spatial moments of the Spencer-Lewis equation is presented that is valid for infinite homogeneous media. From the moments, the electron density distribution as a function of position and path length (energy) is reconstructed for several sample problems involving plane isotropic sources of electrons in aluminium. The results are in excellent agreement with those determined numerically using the streaming ray method. The primary use of the closed form solution will most likely be to generate accurate electron transport benchmark solutions. In principle, the electron density as a function of space, path length, and direction can bemore » determined for planar sources of arbitrary angular distribution.« less

FOREWORD: Special issue on density

NASA Astrophysics Data System (ADS)

Fujii, Kenichi

2004-04-01

This special issue on density was undertaken to provide readers with an overview of the present state of the density standards for solids, liquids and gases, as well as the technologies developed for measuring density. This issue also includes topics on the refractive index of gases and on techniques used for calibrating hydrometers so that almost all areas concerned with density standards are covered in four review articles and seven original articles, most of which describe current research being conducted at national metrology institutes (NMIs). A review article was invited from the Ruhr-Universität Bochum to highlight research on the magnetic suspension densimeters. In metrology, the determinations of the volume of a weight and the density of air are of primary importance in establishing a mass standard because the effect of the buoyancy force of air acting on the weight must be known accurately to determine the mass of the weight. A density standard has therefore been developed at many NMIs with a close relation to the mass standard. Hydrostatic weighing is widely used to measure the volume of a solid. The most conventional hydrostatic weighing method uses water as a primary density standard for measuring the volume of a solid. A brief history of the determination of the density of water is therefore given in a review article, as well as a recommended value for the density of water with a specified isotopic abundance. The most modern technique for hydrostatic weighing uses a solid density standard instead of water. For this purpose, optical interferometers for measuring the diameters of silicon spheres have been developed to convert the length standard into the volume standard with a small uncertainty. A review article is therefore dedicated to describing the state-of-the-art optical interferometers developed for silicon spheres. Relative combined standard uncertainties of several parts in 108 have been achieved today for measuring the volume and density of silicon spheres. These technologies are currently being used not only for establishing a solid density standard, but also for determining the Avogadro constant by the x-ray crystal density method, where the density, molar mass and lattice constant of a silicon crystal are measured based on the definition of the SI units. Considering that much of the present research on the Avogadro constant has been undertaken to replace the present definition of the kilogram with a new definition based on a number of atoms, it is satisfying to note that the most accurate density standard may contribute to a new definition of the kilogram. Differential density measurements by hydrostatic weighing and by the pressure of flotation method developed for measuring the density differences between silicon crystals and solids are given in a review article and three original articles, where combined standard uncertainties of a few parts in 108 have been achieved in measuring relative density differences. These technologies are being used not only for the determination of the Avogadro constant, but also for evaluating defects in silicon crystals used in the semiconductor industry. Another important liquid used in the density standard is mercury because the pressured standard determined from mercury column barometers, the molar gas constant determined from an acoustic resonator, and the Josephson constant determined from a mercury voltmeter are all dependent on the density of mercury. A review article is therefore dedicated to an overview of the history, recommended value and recent progress in the measurement of the density of mercury. This special issue also features the technologies developed for measuring the thermodynamic properties of fluids. New instruments with a magnetic suspension balance have substantially improved the uncertainty in measuring the density of fluids at elevated pressures and temperatures. Two review articles and an original article are therefore dedicated to describing the history, principle and recent progress in magnetic suspension densimeters. When the diamagnetic properties of organic liquids are taken into account, an unprecedented uncertainty of a few parts in 106 can be achieved for density measurements at high pressures. The papers collected in this special issue reflect the general trends in research on density standards. I hope that this special issue will stimulate new directions of research in the density standard, and also help to create more accurate, reliable and convenient methods for many applications. Thanks are addressed to all the authors who have contributed to this special issue on density, to the referees who have given their time, and also to the former editor Professor Martin and the present editor Dr~Williams for their support and useful suggestions in collecting the articles.

Combined effects of compact cevelopment, transportation investments, and road user pricing on vehicle miles traveled in urbanized areas

USGS Publications Warehouse

Ewing, Reid; Hamidi, Shima; Gallivan, Frank; Nelson, Arthur C.; Grace, James B.

2014-01-01

Vehicle miles traveled (VMT) is the primary determinant of traffic congestion, vehicle crashes, greenhouse gas emissions, and other effects of transportation. Two previous studies have sought to explain VMT levels in urbanized areas. This study updates and expands on previous work with more recent data, additional metrics, and structural equation modeling (SEM) to explain VMT levels in 315 urbanized areas. According to SEM, population, income, and gasoline prices are primary exogenous drivers of VMT. Development density is a primary endogenous driver. Urbanized areas with more freeway capacity are significantly less dense and have significantly higher VMT per capita. Areas with more transit service coverage and service frequency have higher development densities and per capita transit use, which leads to lower VMT per capita. The indirect effect of transit on VMT through land use, the so-called land use multiplier, is more than three times greater than the direct effect through transit ridership.

[Effects nutrients on the seedlings root hair development and root growth of Poncirus trifoliata under hydroponics condition].

PubMed

Cao, Xiu; Xia, Ren-Xue; Zhang, De-Jian; Shu, Bo

2013-06-01

Ahydroponics experiment was conducted to study the effects of nutrients (N, P, K, Ca, Mg, Fe, and Mn) deficiency on the length of primary root, the number of lateral roots, and the root hair density, length, and diameter on the primary root and lateral roots of Poncirus trifoliata seedlings. Under the deficiency of each test nutrient, root hair could generate, but was mainly concentrated on the root base and fewer on the root tip. The root hair density on lateral roots was significantly larger than that on primary root, but the root hair length was in adverse. The deficiency of each test nutrient had greater effects on the growth and development of root hairs, with the root hair density on primary root varied from 55.0 to 174.3 mm(-2). As compared with the control, Ca deficiency induced the significant increase of root hair density and length on primary root, P deficiency promoted the root hair density and length on the base and middle part of primary root and on the lateral roots significantly, Fe deficiency increased the root hair density but decreased the root hair length on the tip of primary root significantly, K deficiency significantly decreased the root hair density, length, and diameter on primary root and lateral roots, whereas Mg deficiency increased the root hair length of primary root significantly. In all treatments of nutrient deficiency, the primary root had the similar growth rate, but, with the exceptions of N and Mg deficiency, the lateral roots exhibited shedding and regeneration.

Trapezium Bone Density-A Comparison of Measurements by DXA and CT.

PubMed

Breddam Mosegaard, Sebastian; Breddam Mosegaard, Kamille; Bouteldja, Nadia; Bæk Hansen, Torben; Stilling, Maiken

2018-01-18

Bone density may influence the primary fixation of cementless implants, and poor bone density may increase the risk of implant failure. Before deciding on using total joint replacement as treatment in osteoarthritis of the trapeziometacarpal joint, it is valuable to determine the trapezium bone density. The aim of this study was to: (1) determine the correlation between measurements of bone mineral density of the trapezium obtained by dual-energy X-ray absorptiometry (DXA) scans by a circumference method and a new inner-ellipse method; and (2) to compare those to measurements of bone density obtained by computerized tomography (CT)-scans in Hounsfield units (HU). We included 71 hands from 59 patients with a mean age of 59 years (43-77). All patients had Eaton-Glickel stage II-IV trapeziometacarpal (TM) joint osteoarthritis, were under evaluation for trapeziometacarpal total joint replacement, and underwent DXA and CT wrist scans. There was an excellent correlation (r = 0.94) between DXA bone mineral density measures using the circumference and the inner-ellipse method. There was a moderate correlation between bone density measures obtained by DXA- and CT-scans with (r = 0.49) for the circumference method, and (r = 0.55) for the inner-ellipse method. DXA may be used in pre-operative evaluation of the trapezium bone quality, and the simpler DXA inner-ellipse measurement method can replace the DXA circumference method in estimation of bone density of the trapezium.

High charge state carbon and oxygen ions in Earth's equatorial quasi-trapping region

NASA Technical Reports Server (NTRS)

Christon, S. P.; Hamilton, D. C.; Gloeckler, G.; Eastmann, T. E.

1994-01-01

Observations of energetic (1.5 - 300 keV/e) medium-to-high charge state (+3 less than or equal to Q less than or equal to +7) solar wind origin C and O ions made in the quasi-trapping region (QTR) of Earth's magnetosphere are compared to ion trajectories calculated in model equatorial magnetospheric magnetic and electric fields. These comparisons indicate that solar wind ions entering the QTR on the nightside as an energetic component of the plasma sheet exit the region on the dayside, experiencing little or no charge exchange on the way. Measurements made by the CHarge Energy Mass (CHEM) ion spectrometer on board the Active Magnetospheric Particle Tracer Explorer/Charge Composition Explorer (AMPTE/CCE) spacecraft at 7 less than L less than 9 from September 1984 to January 1989 are the source of the new results contained herein: quantitative long-term determination of number densities, average energies, energy spectra, local time distributions, and their variation with geomagnetic disturbance level as indexed by Kp. Solar wind primaries (ions with charge states unchanged) and their secondaries (ions with generally lower charge states produced from primaries in the magnetosphere via charge exchange)are observed throughout the QTR and have distinctly different local time variations that persist over the entire 4-year analysis interval. During Kp larger than or equal to 3 deg intervals, primary ion (e.g., O(+6)) densities exhibit a pronounced predawn maximum with average energy minimum and a broad near-local-noon density minimum with average energy maximum. Secondary ion (e.g., O(+5)) densities do not have an identifiable predawn peak, rather they have a broad dayside maximum peaked in local morning and a nightside minimum. During Kp less than or equal to 2(-) intervals, primary ion density peaks are less intense, broader in local time extent, and centered near midnight, while secondary ion density local time variations diminish. The long-time-interval baseline helps to refine and extend previous observations; for example, we show that ionospheric contribution to O(+3)) is negligible. Through comparison with model ion trajectories, we interpret the lack of pronounced secondary ion density peaks colocated with the primary density peaks to indicate that: (1) negligible charge exchange occurs at L greater than 7, that is, solar wind secondaries are produced at L less than 7, and (2) solar wind secondaries do not form a significant portion of the plasma sheet population injected into the QTR. We conclude that little of the energetic solar wind secondary ion population is recirculated through the magnetosphere.

Spatial dynamics of large-scale, multistage crab (Callinectes sapidus) dispersal: Determinants and consequences for recruitment

USGS Publications Warehouse

Etherington, L.L.; Eggleston, D.B.

2003-01-01

We assessed determinants and consequences of multistage dispersal on spatial recruitment of the blue crab, Callinectes sapidus, within the Croatan, Albemarle, Pamlico Estuarine System (CAPES), North Carolina, U.S.A. Large-scale sampling of early juvenile crabs over 4 years indicated that spatial abundance patterns were size-dependent and resulted from primary post-larval dispersal (pre-settlement) and secondary juvenile dispersal (early post-settlement). In general, primary dispersal led to high abundances within more seaward habitats, whereas secondary dispersal (which was relatively consistent) expanded the distribution of juveniles, potentially increasing the estuarine nursery capacity. There were strong relationships between juvenile crab density and specific wind characteristics; however, these patterns were spatially explicit. Various physical processes (e.g., seasonal wind events, timing and magnitude of tropical cyclones) interacted to influence dispersal during multiple stages and determined crab recruitment patterns. Our results suggest that the nursery value of different habitats is highly dependent on the dispersal potential (primary and secondary dispersal) to and from these areas, which is largely determined by the relative position of habitats within the estuarine landscape.

Prevalence of osteoporosis in men aged 65-75 in a primary care setting. A practice audit after application of the Canadian 2010 guidelines for osteoporosis screening.

PubMed

Ferrari, Robert

2015-03-01

Current Canadian osteoporosis guidelines recommend routine bone density screening of men at age 65. The purpose of this study is to determine the prevalence of osteoporosis in men aged 65-75 in after application of screening guidelines. All males aged 65-75 years who attended a large primary care clinic were advised of the 2010 Canadian osteoporosis guidelines and advised to obtain a bone density scan at or after their 65th birthday. Those who did not have a bone density scan since their 65th birthday were advised to obtain a scan, unless there was obvious reason not to do so (i.e. known osteoporosis). A record of the results for each patient were kept and tallied to determine the prevalence of osteoporosis. Osteoporosis was defined as a T-score of ≤ -2.5 in either the hip or lumbar spine. Of 574 male subjects in this clinic, between the ages of 65-75, 557 had a bone density scan, either already having done so at the time of being informed of the guidelines or obtaining a scan in the subsequent year after being informed of the guidelines. The prevalence of osteoporosis was 1.6% (9/557, 95% confidence interval 0.8-3.1%) in this sample. The average age of subjects with osteoporosis was 70.5 ± 1.4 years (range 68-75). None of the subjects under 68 years of age were found to have osteoporosis. The prevalence of osteoporosis in unselected male cohorts aged 65 may be too low to justify the routine bone density screening recommended in the 2010 Canadian osteoporosis guidelines.

A model for the effect of real leaks on the transport of microorganisms into a vacuum freeze-dryer.

PubMed

Jennings, T A

1990-01-01

This paper proposes a model for determining the effect that real leaks, whose flow is viscous in nature, could have on the microorganism density in a vacuum freeze-dryer during a drying process. The model considers the entry of microorganisms to result from real leaks stemming from an environment containing a known bioburden. A means for determining the relationship between the rate of pressure rise of the system (ROR) and the density of microorganisms in a system, stemming from an environment of a known bioburden, is examined. The model also considers the change in the bioburden of the dryer with respect to variations in the primary and secondary drying process.

Small-scale cosmic microwave background anisotropies as probe of the geometry of the universe

NASA Technical Reports Server (NTRS)

Kamionkowski, Marc; Spergel, David N.; Sugiyama, Naoshi

1994-01-01

We perform detailed calculations of cosmic microwave background (CMB) anisotropies in a cold dark matter (CDM)-dominated open universe with primordial adiabatic density perturbations for a variety of reionization histories. The CMB anisotropies depend primarily on the geometry of the universe, which in a matter-dominated universe is determined by Omega and the optical depth to the surface of last scattering. In particular, the location on the primary Doppler peak depends primarily on Omega and is fairly insensitive to the other unknown parameters, such as Omega(sub b), h, Lambda, and the shape of the power spectrum. Therefore, if the primordial density perturbations are adiabatic, measurements of CMB anisotropies on small scales may be used to determine Omega.

The role of niacin in raising high-density lipoprotein cholesterol to reduce cardiovascular events in patients with atherosclerotic cardiovascular disease and optimally treated low-density lipoprotein cholesterol Rationale and study design. The Atherothrombosis Intervention in Metabolic syndrome with low HDL/high triglycerides: Impact on Global Health outcomes (AIM-HIGH).

PubMed

2011-03-01

The aim of this study was to test the hypothesis that patients with atherosclerotic cardiovascular (CV) disease optimally treated on a statin but with residual atherogenic dyslipidemia (low high-density lipoprotein cholesterol [HDL-C] and high triglycerides) will benefit from addition of niacin with fewer CV events compared with placebo. Statin monotherapy trials have found 25%-35% CV risk reduction relative to placebo, leaving significant residual risk. Patients with atherogenic dyslipidemia have substantially increased CV risk. Participants were men and women with established CV disease and atherogenic dyslipidemia. Lipid entry criteria varied by gender and statin dose at screening. All participants received simvastatin (or simvastatin plus ezetimibe) at a dose sufficient to maintain low-density lipoprotein cholesterol (LDL-C) 40-80 mg/dL (1.03-2.07 mmol/L). Participants were randomized to extended-release niacin or matching placebo. The primary end point was time to occurrence of the first of the following: coronary heart disease death, nonfatal myocardial infarction, ischemic stroke, hospitalization for acute coronary syndrome, or symptom-driven coronary or cerebral revascularization. This event-driven trial will have 85% power to show a 25% reduction in primary event frequency after 850 patients have experienced a primary outcome event. AIM-HIGH completed enrollment in April 2010. Follow-up is expected to continue through 2012. AIM-HIGH was designed to determine whether treating residual dyslipidemia with niacin further reduces cardiovascular events in patients with CV disease on a statin at target levels of low-density lipoprotein cholesterol. Copyright © 2011 Mosby, Inc. All rights reserved.

Pharmacy density in rural and urban communities in the state of Oregon and the association with hospital readmission rates.

PubMed

Bissonnette, Sarah; Goeres, Leah M; Lee, David S H

2016-01-01

To characterize the pharmacy density in rural and urban communities with hospitals and to examine its association with readmission rates. Ecologic study. Forty-eight rural and urban primary care service areas (PCSAs) in the state of Oregon. All hospitals in the state of Oregon. Pharmacy data were obtained from the Oregon Board of Pharmacy based on active licensure. Pharmacy density was calculated by determining the cumulative number of outpatient pharmacy hours in a PCSA. Oregon hospital 30-day all-cause readmission rates were obtained from the Centers for Medicare and Medicaid Services and were determined with the use of claims data of patients 65 years of age or older who were readmitted to the hospital within 30 days from July 2012 to June 2013. Readmission rates for Oregon hospitals ranged from 13.5% to 16.5%. The cumulative number of pharmacy hours in PCSAs containing a hospital ranged from 54 to 3821 hours. As pharmacy density increased, the readmission rates decreased, asymptotically approaching a predicted 14.7% readmission rate for areas with high pharmacy density. Urban hospitals were in communities likely to have more pharmacy access compared with rural hospitals. Future research should determine if increasing pharmacy access affects readmission rates, especially in rural communities. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Analysis of compaction shock interactions during DDT of low density HMX

NASA Astrophysics Data System (ADS)

Rao, Pratap T.; Gonthier, Keith A.

2017-01-01

Deflagration-to-Detonation Transition (DDT) in confined, low density granular HMX occurs by a complex mechanism that involves compaction shock interactions within the material. Piston driven DDT experiments indicate that detonation is abruptly triggered by the interaction of a strong combustion-supported secondary shock and a piston-supported primary (input) shock, where the nature of the interaction depends on initial packing density and primary shock strength. These interactions influence transition by affecting dissipative heating within the microstructure during pore collapse. Inert meso-scale simulations of successive shock loading of low density HMX are performed to examine how dissipation and hot-spot formation are affected by the initial density, and the primary and secondary shock strengths. This information is used to formulate an ignition and burn model for low density HMX that accounts for the effect of shock densensitization on burn. Preliminary DDT predictions are presented that illustrate how primary shock strength affects the transition mechanism.

The insertion torque-depth curve integral as a measure of implant primary stability: An in vitro study on polyurethane foam blocks.

PubMed

Di Stefano, Danilo Alessio; Arosio, Paolo; Gastaldi, Giorgio; Gherlone, Enrico

2017-07-08

Recent research has shown that dynamic parameters correlate with insertion energy-that is, the total work needed to place an implant into its site-might convey more reliable information concerning immediate implant primary stability at insertion than the commonly used insertion torque (IT), the reverse torque (RT), or the implant stability quotient (ISQ). Yet knowledge on these dynamic parameters is still limited. The purpose of this in vitro study was to evaluate whether an energy-related parameter, the torque-depth curve integral (I), could be a reliable measure of primary stability. This was done by assessing if (I) measurement was operator-independent, by investigating its correlation with other known primary stability parameters (IT, RT, or ISQ) by quantifying the (I) average error and correlating (I), IT, RT, and ISQ variations with bone density. Five operators placed 200 implants in polyurethane foam blocks of different densities using a micromotor that calculated the (I) during implant placement. Primary implant stability was assessed by measuring the ISQ, IT, and RT. ANOVA tests were used to evaluate whether measurements were operator independent (P>.05 in all cases). A correlation analysis was performed between (I) and IT, ISQ, and RT. The (I) average error was calculated and compared with that of the other parameters by ANOVA. (I)-density, IT-density, ISQ-density, and RT-density plots were drawn, and their slopes were compared by ANCOVA. The (I) measurements were operator independent and correlated with IT, ISQ, and RT. The average error of these parameters was not significantly different (P>.05 in all cases). The (I)-density, IT-density, ISQ-density, and RT-density curves were linear in the 0.16 to 0.49 g/cm³ range, with the (I)-density curves having a significantly greater slope than those regarding the other parameters (P≤.001 in all cases). The torque-depth curve integral (I) provides a reliable assessment of primary stability and shows a greater sensitivity to density variations than other known primary stability parameters. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A novel method for flow pattern identification in unstable operational conditions using gamma ray and radial basis function.

PubMed

Roshani, G H; Nazemi, E; Roshani, M M

2017-05-01

Changes of fluid properties (especially density) strongly affect the performance of radiation-based multiphase flow meter and could cause error in recognizing the flow pattern and determining void fraction. In this work, we proposed a methodology based on combination of multi-beam gamma ray attenuation and dual modality densitometry techniques using RBF neural network in order to recognize the flow regime and determine the void fraction in gas-liquid two phase flows independent of the liquid phase changes. The proposed system is consisted of one 137 Cs source, two transmission detectors and one scattering detector. The registered counts in two transmission detectors were used as the inputs of one primary Radial Basis Function (RBF) neural network for recognizing the flow regime independent of liquid phase density. Then, after flow regime identification, three RBF neural networks were utilized for determining the void fraction independent of liquid phase density. Registered count in scattering detector and first transmission detector were used as the inputs of these three RBF neural networks. Using this simple methodology, all the flow patterns were correctly recognized and the void fraction was predicted independent of liquid phase density with mean relative error (MRE) of less than 3.28%. Copyright © 2017 Elsevier Ltd. All rights reserved.

Estimating large carnivore populations at global scale based on spatial predictions of density and distribution – Application to the jaguar (Panthera onca)

PubMed Central

Robinson, Hugh S.; Abarca, Maria; Zeller, Katherine A.; Velasquez, Grisel; Paemelaere, Evi A. D.; Goldberg, Joshua F.; Payan, Esteban; Hoogesteijn, Rafael; Boede, Ernesto O.; Schmidt, Krzysztof; Lampo, Margarita; Viloria, Ángel L.; Carreño, Rafael; Robinson, Nathaniel; Lukacs, Paul M.; Nowak, J. Joshua; Salom-Pérez, Roberto; Castañeda, Franklin; Boron, Valeria; Quigley, Howard

2018-01-01

Broad scale population estimates of declining species are desired for conservation efforts. However, for many secretive species including large carnivores, such estimates are often difficult. Based on published density estimates obtained through camera trapping, presence/absence data, and globally available predictive variables derived from satellite imagery, we modelled density and occurrence of a large carnivore, the jaguar, across the species’ entire range. We then combined these models in a hierarchical framework to estimate the total population. Our models indicate that potential jaguar density is best predicted by measures of primary productivity, with the highest densities in the most productive tropical habitats and a clear declining gradient with distance from the equator. Jaguar distribution, in contrast, is determined by the combined effects of human impacts and environmental factors: probability of jaguar occurrence increased with forest cover, mean temperature, and annual precipitation and declined with increases in human foot print index and human density. Probability of occurrence was also significantly higher for protected areas than outside of them. We estimated the world’s jaguar population at 173,000 (95% CI: 138,000–208,000) individuals, mostly concentrated in the Amazon Basin; elsewhere, populations tend to be small and fragmented. The high number of jaguars results from the large total area still occupied (almost 9 million km2) and low human densities (< 1 person/km2) coinciding with high primary productivity in the core area of jaguar range. Our results show the importance of protected areas for jaguar persistence. We conclude that combining modelling of density and distribution can reveal ecological patterns and processes at global scales, can provide robust estimates for use in species assessments, and can guide broad-scale conservation actions. PMID:29579129

On the maximum energy of non-thermal particles in the primary hotspot of Cygnus A

NASA Astrophysics Data System (ADS)

Araudo, Anabella T.; Bell, Anthony R.; Blundell, Katherine M.; Matthews, James H.

2018-01-01

We study particle acceleration and magnetic field amplification in the primary hotspot in the north-west jet of radiogalaxy Cygnus A. By using the observed flux density at 43 GHz in a well-resolved region of this hotspot, we determine the minimum value of the jet density and constrain the magnitude of the magnetic field. We find that a jet with density greater than 5 × 10-5 cm-3 and hotspot magnetic field in the range 50-400 μG are required to explain the synchrotron emission at 43 GHz. The upper-energy cut-off in the hotspot synchrotron spectrum is at a frequency ≲5 × 1014 Hz, indicating that the maximum energy of non-thermal electrons accelerated at the jet reverse shock is Ee, max ∼ 0.8 TeV in a magnetic field of 100 μG. Based on the condition that the magnetic-turbulence scalelength has to be larger than the plasma skin depth, and that the energy density in non-thermal particles cannot violate the limit imposed by the jet kinetic luminosity, we show that Ee, max cannot be constrained by synchrotron losses as traditionally assumed. In addition to that, and assuming that the shock is quasi-perpendicular, we show that non-resonant hybrid instabilities generated by the streaming of cosmic rays with energy Ee, max can grow fast enough to amplify the jet magnetic field up to 50-400 μG and accelerate particles up to the maximum energy Ee, max observed in the Cygnus A primary hotspot.

Primary care physician supply and other key determinants of health care utilisation: the case of Switzerland

PubMed Central

Busato, André; Künzi, Beat

2008-01-01

Background The Swiss government decided to freeze new accreditations for physicians in private practice in Switzerland based on the assumption that demand-induced health care spending may be cut by limiting care offers. This legislation initiated an ongoing controversial public debate in Switzerland. The aim of this study is therefore the determination of socio-demographic and health system-related factors of per capita consultation rates with primary care physicians in the multicultural population of Switzerland. Methods The data were derived from the complete claims data of Swiss health insurers for 2004 and included 21.4 million consultations provided by 6564 Swiss primary care physicians on a fee-for-service basis. Socio-demographic data were obtained from the Swiss Federal Statistical Office. Utilisation-based health service areas were created and were used as observational units for statistical procedures. Multivariate and hierarchical models were applied to analyze the data. Results Models within the study allowed the definition of 1018 primary care service areas with a median population of 3754 and an average per capita consultation rate of 2.95 per year. Statistical models yielded significant effects for various geographical, socio-demographic and cultural factors. The regional density of physicians in independent practice was also significantly associated with annual consultation rates and indicated an associated increase 0.10 for each additional primary care physician in a population of 10,000 inhabitants. Considerable differences across Swiss language regions were observed with reference to the supply of ambulatory health resources provided either by primary care physicians, specialists, or hospital-based ambulatory care. Conclusion The study documents a large small-area variation in utilisation and provision of health care resources in Switzerland. Effects of physician density appeared to be strongly related to Swiss language regions and may be rooted in the different cultural backgrounds of the served populations. PMID:18190705

Primary care physician supply and other key determinants of health care utilisation: the case of Switzerland.

PubMed

Busato, André; Künzi, Beat

2008-01-11

The Swiss government decided to freeze new accreditations for physicians in private practice in Switzerland based on the assumption that demand-induced health care spending may be cut by limiting care offers. This legislation initiated an ongoing controversial public debate in Switzerland. The aim of this study is therefore the determination of socio-demographic and health system-related factors of per capita consultation rates with primary care physicians in the multicultural population of Switzerland. The data were derived from the complete claims data of Swiss health insurers for 2004 and included 21.4 million consultations provided by 6564 Swiss primary care physicians on a fee-for-service basis. Socio-demographic data were obtained from the Swiss Federal Statistical Office. Utilisation-based health service areas were created and were used as observational units for statistical procedures. Multivariate and hierarchical models were applied to analyze the data. Models within the study allowed the definition of 1018 primary care service areas with a median population of 3754 and an average per capita consultation rate of 2.95 per year. Statistical models yielded significant effects for various geographical, socio-demographic and cultural factors. The regional density of physicians in independent practice was also significantly associated with annual consultation rates and indicated an associated increase 0.10 for each additional primary care physician in a population of 10,000 inhabitants. Considerable differences across Swiss language regions were observed with reference to the supply of ambulatory health resources provided either by primary care physicians, specialists, or hospital-based ambulatory care. The study documents a large small-area variation in utilisation and provision of health care resources in Switzerland. Effects of physician density appeared to be strongly related to Swiss language regions and may be rooted in the different cultural backgrounds of the served populations.

Biomechanical evaluation of oversized drilling technique on primary implant stability measured by insertion torque and resonance frequency analysis

PubMed Central

Santamaría-Arrieta, Gorka; Brizuela-Velasco, Aritza; Fernández-González, Felipe J.; Chávarri-Prado, David; Chento-Valiente, Yelko; Solaberrieta, Eneko; Diéguez-Pereira, Markel; Yurrebaso-Asúa, Jaime

2016-01-01

Background This study evaluated the influence of implant site preparation depth on primary stability measured by insertion torque and resonance frequency analysis (RFA). Material and Methods Thirty-two implant sites were prepared in eight veal rib blocks. Sixteen sites were prepared using the conventional drilling sequence recommended by the manufacturer to a working depth of 10mm. The remaining 16 sites were prepared using an oversize drilling technique (overpreparation) to a working depth of 12mm. Bone density was determined using cone beam computerized tomography (CBCT). The implants were placed and primary stability was measured by two methods: insertion torque (Ncm), and RFA (implant stability quotient [ISQ]). Results The highest torque values were achieved by the conventional drilling technique (10mm). The ANOVA test confirmed that there was a significant correlation between torque and drilling depth (p<0.05). However, no statistically significant differences were obtained between ISQ values at 10 or 12 mm drilling depths (p>0.05) at either measurement direction (cortical and medullar). No statistical relation between torque and ISQ values was identified, or between bone density and primary stability (p >0.05). Conclusions Vertical overpreparation of the implant bed will obtain lower insertion torque values, but does not produce statistically significant differences in ISQ values. Key words:Implant stability quotient, overdrilling, primary stability, resonance frequency analysis, torque. PMID:27398182

Predicted optical performance of the high-altitude balloon experiment (HABE) telescope in an adverse thermal environment

NASA Astrophysics Data System (ADS)

Akau, Ronald L.; Givler, Richard C.; Eastman, Daniel R.

1994-07-01

The High-Altitude Balloon Experiment telescope was designed to operate at an ambient temperature of -55 degree(s)C and an altitude of 26 km, using a precooled primary mirror. Although at this altitude the air density is only 1.4 percent of the value at sea level, the temperature gradients within the telescope are high enough to deform the optical wavefront. This problem is considerably lessened by precooling the primary mirror to -35 degree(s)C. This paper describes the application of several codes to determine the range of wavefront deformation during a mission.

[Prevalence of dyslipidemia and its influential factors in 2 028 students from primary and middle schools in Changsha].

PubMed

Li, Yamei; Luo, Jiayou; Ma, Jun; Zou, Zhiyong; Liu, Xiaoqun; Li, Huixia

2017-06-28

To determine the prevalence of dyslipidemia in students from the primary and middle schools and the influential factors, and to provide evidence for the prevention and control of dyslipidemia and relevant chronic diseases in primary and middle schools. 
 Methods: A total of 2 028 students aged 7 to 17 from the primary and middle schools in Changsha were selected by stratified random cluster sampling. The contents of the study included questionnaire survey, physical measurement and blood tests for fasting blood triglyceride (TG), total cholesterol (TC), low-density lipoprotein cholesterol (LDL-C), and high-density lipoprotein cholesterol (HDL-C) levels. Non-high-density lipoprotein cholesterol (non-HDL-C) level was calculated by TC level minus HDL-C level. Chi-square test and non-conditional logistic regression model were used to analyze the factors that contributed to dyslipidemia.
 Results: The dyslipidemia rate was 18.6%, and the abnormal rates of TG, TC, LDL-C, non-HDL-C and HDL-C were 6.8%, 5.6%, 2.3%, 4.2% and 8.6%, respectively. By chi-square test, the dyslipidemia rate in students with different ages, home locations, BMI groups, central obesity, time on watching TV or playing computer per day, and daily sleep time was statistically significant. Non-conditional logistic regression analysis showed that home location for the city (OR=1.332), overweight (OR=1.548), obesity (OR=2.201), central obesity (OR=1.695), watching TV or playing computer for more than 2 hours per day (OR=1.357), daily sleep time longer than 11 hours (OR=2.518) were the risk factors for dyslipidemia in students from the primary and middle schools. 
 Conclusion: Nearly 1/5 primary and middle school students show dyslipidemia, which is associated with obesity and other bad behaviors.

Judging a salmon by its spots: environmental variation is the primary determinant of spot patterns in Salmo salar.

PubMed

Jørgensen, Katarina M; Solberg, Monica F; Besnier, Francois; Thorsen, Anders; Fjelldal, Per Gunnar; Skaala, Øystein; Malde, Ketil; Glover, Kevin A

2018-04-12

In fish, morphological colour changes occur from variations in pigment concentrations and in the morphology, density, and distribution of chromatophores in the skin. However, the underlying mechanisms remain unresolved in most species. Here, we describe the first investigation into the genetic and environmental basis of spot pattern development in one of the world's most studied fishes, the Atlantic salmon. We reared 920 salmon from 64 families of domesticated, F1-hybrid and wild origin in two contrasting environments (Hatchery; tanks for the freshwater stage and sea cages for the marine stage, and River; a natural river for the freshwater stage and tanks for the marine stage). Fish were measured, photographed and spot patterns evaluated. In the Hatchery experiment, significant but modest differences in spot density were observed among domesticated, F1-hybrid (1.4-fold spottier than domesticated) and wild salmon (1.7-fold spottier than domesticated). A heritability of 6% was calculated for spot density, and a significant QTL on linkage group SSA014 was detected. In the River experiment, significant but modest differences in spot density were also observed among domesticated, F1-hybrid (1.2-fold spottier than domesticated) and wild salmon (1.8-fold spottier than domesticated). Domesticated salmon were sevenfold spottier in the Hatchery vs. River experiment. While different wild populations were used for the two experiments, on average, these were 6.2-fold spottier in the Hatchery vs. River experiment. Fish in the Hatchery experiment displayed scattered to random spot patterns while fish in the River experiment displayed clustered spot patterns. These data demonstrate that while genetics plays an underlying role, environmental variation represents the primary determinant of spot pattern development in Atlantic salmon.

The development of wing shape in Lepidoptera: mitotic density, not orientation, is the primary determinant of shape.

PubMed

Nijhout, H Frederik; Cinderella, Margaret; Grunert, Laura W

2014-03-01

The wings of butterflies and moths develop from imaginal disks whose structure is always congruent with the final adult wing. It is therefore possible to map every point on the imaginal disk to a location on the adult wing throughout ontogeny. We studied the growth patterns of the wings of two distantly related species with very different adult wing shapes, Junonia coenia and Manduca sexta. The shape of the wing disks change throughout their growth phase in a species-specific pattern. We measured mitotic densities and mitotic orientation in successive stages of wing development approximately one cell division apart. Cell proliferation was spatially patterned, and the density of mitoses was highly correlated with local growth. Unlike other systems in which the direction of mitoses has been viewed as the primary determinant of directional growth, we found that in these two species the direction of growth was only weakly correlated with the orientation of mitoses. Directional growth appears to be imposed by a constantly changing spatial pattern of cell division coupled with a weak bias in the orientation of cell division. Because growth and cell division in imaginal disk require ecdysone and insulin signaling, the changing spatial pattern of cell division may due to a changing pattern of expression of receptors or downstream elements in the signaling pathways for one or both of these hormones. Evolution of wing shape comes about by changes in the progression of spatial patterns of cell division. © 2014 Wiley Periodicals, Inc.

Effect of Mass Flow on Stack Eductor Performance.

DTIC Science & Technology

1984-06-01

absolute viscosity, lbf-sec/ft2 - density, Ibm/ft 3 "function of" ENGLISH LETTER SYMBOLS 2 A - area, in , ft B - atmospheric pressure, in Hg c - sonic... absolute temperature ratio T* - tertiary flow to primary flow absolute temperature t ratio - secondary -o primary mass flow rate ratio W* - tertiary to...secondary to primary absolute Tp temperature ratio TiL tertiary to primary absolute -TE temperature ratio secondary to primary flow density ratio

Use of selection indices to model the functional response of predators

USGS Publications Warehouse

Joly, D.O.; Patterson, B.R.

2003-01-01

The functional response of a predator to changing prey density is an important determinant of stability of predatora??prey systems. We show how Manly's selection indices can be used to distinguish between hyperbolic and sigmoidal models of a predator functional response to primary prey density in the presence of alternative prey. Specifically, an inverse relationship between prey density and preference for that prey results in a hyperbolic functional response while a positive relationship can yield either a hyperbolic or sigmoidal functional response, depending on the form and relative magnitudes of the density-dependent preference model, attack rate, and handling time. As an example, we examine wolf (Canis lupus) functional response to moose (Alces alces) density in the presence of caribou (Rangifer tarandus). The use of selection indices to evaluate the form of the functional response has significant advantages over previous attempts to fit Holling's functional response curves to killing-rate data directly, including increased sensitivity, use of relatively easily collected data, and consideration of other explanatory factors (e.g., weather, seasons, productivity).

High prevalence of dyslipidemia among primary care patients with hypertension and diabetes in Jamaica.

PubMed

Harris, Michelle A; Ferguson, Trevor S; Boyne, Michael S; Figueroa, J Peter

2017-01-01

The aim of the study was to determine the prevalence of dyslipidemia among primary care patients with hypertension and diabetes in Jamaica and the proportion of patients who achieve recommended targets. An audit of 500 dockets of adult patients with chronic disease attending public primary care clinics in Jamaica was conducted between October and December 2013. Data were collected on patient characteristics including medical history, medications, anthropometry, and lipid profiles (since January 1, 2011). Lipid targets were based on the Ministry of Health 2007 management guidelines. Stepwise multivariable logistic regression analysis was performed to determine the predictors of achieving lipid targets. Four hundred and thirty-seven patient records had a lipid profile done and 90% of these had at least one abnormal lipid value. 15.3% of the patients achieved the low density lipoprotein cholesterol (LDL-C) target, 63.2% high density lipoprotein cholesterol (HDL-C), 85.1% triglycerides and 57.4% the total cholesterol target. Statins were prescribed for 49% and these patients were less likely to achieve LDL-C (OR = 0.57; 95% CI: 0.33-0.97; p = 0.04) or total cholesterol (OR = 0.21; 95% CI: 0.13-0.33; p < 0.001) targets. Patients over 80 years were more likely to achieve the LDL-C target (OR = 3.21; 95% CI: 1.64-6.28; p = 0.002) than those less than 50 years old. More men than women achieved total cholesterol targets (OR = 2.2; 95% CI: 1.4-3.6; p = 0.001). Dyslipidemia is widespread among primary care patients with hypertension and diabetes. The proportion of patients who achieve the respective lipid targets must be documented and routinely monitored and appropriate medication and lifestyle changes implemented to improve this.

The Global Contribution of Secondary Craters on the Icy Satellites

NASA Astrophysics Data System (ADS)

Hoogenboom, T.; Johnson, K. E.; Schenk, P.

2014-12-01

At present, surface ages of bodies in the Outer Solar System are determined only from crater size-frequency distributions (a method dependent on an understanding of the projectile populations responsible for impact craters in these planetary systems). To derive accurate ages using impact craters, the impactor population must be understood. Impact craters in the Outer Solar System can be primary, secondary or sesquinary. The contribution of secondary craters to the overall population has recently become a "topic of interest." Our objective is to better understand the contribution of dispersed secondary craters to the small crater populations, and ultimately that of small comets to the projectile flux on icy satellites in general. We measure the diameters of obvious secondary craters (determined by e.g. irregular crater shape, small size, clustering) formed by all primary craters on Ganymede for which we have sufficiently high resolution data to map secondary craters. Primary craters mapped range from approximately 40 km to 210 km. Image resolution ranges from 45 to 440 m/pixel. Bright terrain on Ganymede is our primary focus. These resurfaced terrains have relatively low crater densities and serve as a basis for characterizing secondary populations as a function of primary size on an icy body for the first time. Although focusing on Ganymede, we also investigate secondary crater size, frequency, distribution, and formation, as well as secondary crater chain formation on icy satellites throughout the Saturnian and Jovian systems principally Rhea. We compare our results to similar studies of secondary cratering on the Moon and Mercury. Using Galileo and Voyager data, we have identified approximately 3,400 secondary craters on Ganymede. In some cases, we measured crater density as a function of distance from a primary crater. Because of the limitations of the Galileo data, it is necessary to extrapolate from small data sets to the global population of secondary craters. Nonetheless, we confirm that secondary craters on Ganymede have narrow size-frequency distributions and that they correlate with primary crater diameter. From these data we will evaluate the contribution of secondary craters over a range of crater diameters.

Why are there more arboreal ant species in primary than in secondary tropical forests?

PubMed

Klimes, Petr; Idigel, Cliffson; Rimandai, Maling; Fayle, Tom M; Janda, Milan; Weiblen, George D; Novotny, Vojtech

2012-09-01

1. Species diversity of arboreal arthropods tends to increase during rainforest succession so that primary forest communities comprise more species than those from secondary vegetation, but it is not well understood why. Primary forests differ from secondary forests in a wide array of factors whose relative impacts on arthropod diversity have not yet been quantified. 2. We assessed the effects of succession-related determinants on a keystone ecological group, arboreal ants, by conducting a complete census of 1332 ant nests from all trees with diameter at breast height ≥ 5 cm occurring within two (unreplicated) 0·32-ha plots, one in primary and one in secondary lowland forest in New Guinea. Specifically, we used a novel rarefaction-based approach to match number, size distribution and taxonomic structure of trees in primary forest communities to those in secondary forest and compared the resulting numbers of ant species. 3. In total, we recorded 80 nesting ant species from 389 trees in primary forest but only 42 species from 295 trees in secondary forest. The two habitats did not differ in the mean number of ant species per tree or in the relationship between ant diversity and tree size. However, the between-tree similarity of ant communities was higher in secondary forest than in primary forest, as was the between-tree nest site similarity, suggesting that secondary trees were more uniform in providing nesting microhabitats. 4. Using our rarefaction method, the difference in ant species richness between two forest types was partitioned according to the effects of higher tree density (22·6%), larger tree size (15·5%) and higher taxonomic diversity of trees (14·3%) in primary than in secondary forest. The remaining difference (47·6%) was because of higher beta diversity of ant communities between primary forest trees. In contrast, difference in nest density was explained solely by difference in tree density. 5. Our study shows that reduction in plant taxonomic diversity in secondary forests is not the main driver of the reduction in canopy ant species richness. We suggest that the majority of arboreal species losses in secondary tropical forests are attributable to simpler vegetation structure, combined with lower turnover of nesting microhabitats between trees. © 2012 The Authors. Journal of Animal Ecology © 2012 British Ecological Society.

A figure of merit for AMTEC electrodes

NASA Technical Reports Server (NTRS)

Underwood, M. L.; Williams, R. M.; Jeffries-Nakamura, B.; Ryan, M. A.

1991-01-01

As a method to compare the results of alkali metal thermoelectric converter (AMTEC) electrode performance measured under different conditions, an AMTEC figure of merit called ZA is proposed. This figure of merit is the ratio of the experimental maximum power for an electrode to a calculated maximum power density as determined from a recently published electrode performance model. The calculation of a maximum power density assumes that certain loss terms in the electrode can be reduced to essentially zero by improved cell design and construction, and that the electrochemical exchange current is determined from a standard value. Other losses in the electrode are considered inherent to the electrode performance. Thus, these terms remain in the determination of the calculated maximum power. A value of ZA near one, then, indicates an electrode performance near the maximum possible performance. The primary limitation of this calculation is that the small electrode effect cannot be included. This effect leads to anomalously high values of ZA. Thus, the electrode area should be reported along with the figure of merit.

Determination of NH2 concentration on 3-aminopropyl tri-ethoxy silane layers and cyclopropylamine plasma polymers by liquid-phase derivatization with 5-iodo 2-furaldehyde

NASA Astrophysics Data System (ADS)

Manakhov, Anton; Čechal, Jan; Michlíček, Miroslav; Shtansky, Dmitry V.

2017-08-01

The quantification of concentration of primary amines, e.g. in plasma polymerized layers is a very important task for surface analysis. However, the commonly used procedure, such as gas phase derivatization with benzaldehydes, shows several drawbacks, the most important of which are the side reaction effects. In the present study we propose and validate a liquid phase derivatization using 5-iodo 2-furaldehyde (IFA). It was demonstrated that the content of NH2 groups can be determined from the atomic concentrations measured by X-ray photoelectron spectroscopy (XPS), in particular from the ratio of I 3d and N 1s peak intensities. First, we demonstrate the method on a prototypical system such as 3-aminopropyl tri-ethoxy silane (APTES) layer. Here the XPS analysis carried out after reaction of APTES layer with IFA gives the fraction of primary amines (NH2/N) of 38.3 ± 7.9%. Comparing this value with that obtained by N 1s curve fitting of APTES layer giving 40.9 ± 9.5% of amine groups, it can be concluded that all primary amines were derivatized by reaction with IFA. The second system to demonstrate the method comprises cyclopropylamine (CPA) plasma polymers that were free from conjugated imines. In this case the method gives the NH2 fraction ∼8.5%. This value is closely matching the NH2/N ratio estimated by 4-trifluoromethyl benzaldehyde (TFBA) derivatization. The reaction of IFA with CPA plasma polymer exhibiting high density of conjugated imines revealed the NH2/N fraction of ∼10.8%. This value was significantly lower compared to 17.3% estimated by TFBA derivatization. As the overestimated density of primary amines measured by TFBA derivatization is probably related to the side reaction of benzaldehydes with conjugated imines, the proposed IFA derivatization of primary amines can be an alternative procedure for the quantification of surface amine groups.

Predicting Space Weather Effects on Close Approach Events

NASA Technical Reports Server (NTRS)

Hejduk, Matthew D.; Newman, Lauri K.; Besser, Rebecca L.; Pachura, Daniel A.

2015-01-01

The NASA Robotic Conjunction Assessment Risk Analysis (CARA) team sends ephemeris data to the Joint Space Operations Center (JSpOC) for conjunction assessment screening against the JSpOC high accuracy catalog and then assesses risk posed to protected assets from predicted close approaches. Since most spacecraft supported by the CARA team are located in LEO orbits, atmospheric drag is the primary source of state estimate uncertainty. Drag magnitude and uncertainty is directly governed by atmospheric density and thus space weather. At present the actual effect of space weather on atmospheric density cannot be accurately predicted because most atmospheric density models are empirical in nature, which do not perform well in prediction. The Jacchia-Bowman-HASDM 2009 (JBH09) atmospheric density model used at the JSpOC employs a solar storm active compensation feature that predicts storm sizes and arrival times and thus the resulting neutral density alterations. With this feature, estimation errors can occur in either direction (i.e., over- or under-estimation of density and thus drag). Although the exact effect of a solar storm on atmospheric drag cannot be determined, one can explore the effects of JBH09 model error on conjuncting objects' trajectories to determine if a conjunction is likely to become riskier, less risky, or pass unaffected. The CARA team has constructed a Space Weather Trade-Space tool that systematically alters the drag situation for the conjuncting objects and recalculates the probability of collision for each case to determine the range of possible effects on the collision risk. In addition to a review of the theory and the particulars of the tool, the different types of observed output will be explained, along with statistics of their frequency.

Cyclic development of igneous features and their relationship to high-temperature hydrothermal features in the Henderson porphyry molybdenum deposit, Colorado

USGS Publications Warehouse

Carten, R.B.; Geraghty, E.P.; Walker, B.M.

1988-01-01

The Henderson porphyry molybdenum deposit was formed by the superposition of coupled alteration and mineralization events, of varying intensity and size, that were associated with each of at least 11 intrusions. Deposition of molybdenite was accompanied by time-equivalent silicic and potassic alteration. High-temperature alteration and mineralization are spatially and temporally linked to the crystallization of compositionally zoned magma in the apex of stocks. Differences in hydrothermal features associated with each intrusion (e.g., mass of ore, orientation and type of veins, density of veins, and intensity of alteration) correlate with differences in primary igneous features (e.g., composition, texture, morphology, and size). The systematic relations between hydrothermal and magmatic features suggest that primary magma compositions, including volatile contents, largely control the geometry, volume, level of emplacement, and mechanisms of crystallization of stocks. These elements in turn govern the orientations and densities of fractures, which ultimately determine the distribution patterns of hydrothermal alteration and mineralization. -from Authors

Metabolic alterations, HFE gene mutations and atherogenic lipoprotein modifications in patients with primary iron overload.

PubMed

Meroño, Tomás; Brites, Fernando; Dauteuille, Carolane; Lhomme, Marie; Menafra, Martín; Arteaga, Alejandra; Castro, Marcelo; Saez, María Soledad; Ballerga, Esteban González; Sorroche, Patricia; Rey, Jorge; Lesnik, Philippe; Sordá, Juan Andrés; Chapman, M John; Kontush, Anatol; Daruich, Jorge

2015-05-01

Iron overload (IO) has been associated with glucose metabolism alterations and increased risk of cardiovascular disease (CVD). Primary IO is associated with mutations in the HFE gene. To which extent HFE gene mutations and metabolic alterations contribute to the presence of atherogenic lipoprotein modifications in primary IO remains undetermined. The present study aimed to assess small, dense low-density lipoprotein (LDL) levels, chemical composition of LDL and high-density lipoprotein (HDL) particles, and HDL functionality in IO patients. Eighteen male patients with primary IO and 16 sex- and age-matched controls were recruited. HFE mutations (C282Y, H63D and S65C), measures of insulin sensitivity and secretion (calculated from the oral glucose tolerance test), chemical composition and distribution profile of LDL and HDL subfractions (isolated by gradient density ultracentrifugation) and HDL functionality (as cholesterol efflux and antioxidative activity) were studied. IO patients compared with controls exhibited insulin resistance (HOMA-IR (homoeostasis model assessment-estimated insulin resistance): +93%, P< 0.001). Metabolic profiles differed across HFE genotypes. C282Y homozygotes (n=7) presented a reduced β-cell function and insulin secretion compared with non-C282Y patients (n=11) (-58% and -73%, respectively, P< 0.05). In addition, C282Y homozygotes featured a predominance of large, buoyant LDL particles (C282Y: 43±5; non-C282Y: 25±8; controls: 32±7%; P< 0.001), whereas non-C282Y patients presented higher amounts of small, dense LDL (C282Y: 23±5; non-C282Y: 39±10; controls: 26±4%; P< 0.01). HDL particles were altered in C282Y homozygotes. However, HDL functionality was conserved. In conclusion, metabolic alterations and HFE gene mutations are involved in the presence of atherogenic lipoprotein modifications in primary IO. To what extent such alterations could account for an increase in CVD risk remains to be determined.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brook, I.M.

Five Thalassia communities with high blade density (greater than 3,000 blades/m/sup 2/) were sampled by suction dredge in April 1973. Four sites were in south Biscayne Bay, and one was at Murray Key in the Everglades National Park on the southwest coast of Florida. Macrofaunal abundance ranged from 292 to 10,728 individuals/m/sup 2/. It is postulated that a high standing crop of seagrass may not be the primary determining factor in faunal abundance.

Primary energy reconstruction from the charged particle densities recorded at 500 m distance from shower core with the KASCADE-Grande detector

NASA Astrophysics Data System (ADS)

Toma, G.; Apel, W. D.; Arteaga, J. C.; Bekk, K.; Bertaina, M.; Blümer, J.; Bozdog, H.; Brâncuş, I. M.; Buchholz, P.; Cantoni, E.; Chiavassa, A.; Cossavella, F.; Daumiller, K.; de Souza, V.; di Pierro, F.; Doll, P.; Engel, R.; Engler, J.; Finger, M.; Fuhrmann, D.; Ghia, P. L.; Gils, H. J.; Glasstetter, R.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Huege, T.; Isar, P. G.; Kampert, K.-H.; Kang, D.; Kickelbick, D.; Klages, H. O.; Link, K.; Łuczak, P.; Ludwig, M.; Mathes, H. J.; Mayer, H. J.; Melissas, M.; Milke, J.; Mitrică, B.; Morello, C.; Navarra, G.; Nehls, S.; Oehlschläger, J.; Ostapchenko, S.; Over, S.; Palmieri, N.; Petcu, M.; Pierog, T.; Rebel, H.; Roth, M.; Schieler, H.; Schröder, F. G.; Sima, O.; Trinchero, G. C.; Ulrich, H.; Weindl, A.; Wochele, J.; Wommer, M.; Zabierowski, J.

2011-05-01

Previous EAS investigations have shown that for a fixed primary energy the charged particle density becomes independent of the primary mass at certain (fixed) distances from the shower axis. This feature can be used as an estimator for the primary energy. We present results on the reconstruction of the primary energy spectrum of cosmic rays from the experimentally recorded S(500) observable (the density of charged particles at a distance of 500 m to the shower core as measured in a plane normal to the shower axis) using the KASCADE-Grande detector array. The KASCADE-Grande experiment is hosted by the Karlsruhe Institute for Technology - Campus North, Karlsruhe, Germany, 110 m a.s.l. and operated by an international collaboration. The obtained primary energy spectrum is presented along with the result of another reconstruction technique presently employed at KASCADE-Grande.

Spectral integration in primary auditory cortex attributable to temporally precise convergence of thalamocortical and intracortical input.

PubMed

Happel, Max F K; Jeschke, Marcus; Ohl, Frank W

2010-08-18

Primary sensory cortex integrates sensory information from afferent feedforward thalamocortical projection systems and convergent intracortical microcircuits. Both input systems have been demonstrated to provide different aspects of sensory information. Here we have used high-density recordings of laminar current source density (CSD) distributions in primary auditory cortex of Mongolian gerbils in combination with pharmacological silencing of cortical activity and analysis of the residual CSD, to dissociate the feedforward thalamocortical contribution and the intracortical contribution to spectral integration. We found a temporally highly precise integration of both types of inputs when the stimulation frequency was in close spectral neighborhood of the best frequency of the measurement site, in which the overlap between both inputs is maximal. Local intracortical connections provide both directly feedforward excitatory and modulatory input from adjacent cortical sites, which determine how concurrent afferent inputs are integrated. Through separate excitatory horizontal projections, terminating in cortical layers II/III, information about stimulus energy in greater spectral distance is provided even over long cortical distances. These projections effectively broaden spectral tuning width. Based on these data, we suggest a mechanism of spectral integration in primary auditory cortex that is based on temporally precise interactions of afferent thalamocortical inputs and different short- and long-range intracortical networks. The proposed conceptual framework allows integration of different and partly controversial anatomical and physiological models of spectral integration in the literature.

Conventional and power spectrum analysis of the effects of zolpidem on sleep EEG in patients with chronic primary insomnia.

PubMed

Monti, J M; Alvariño, F; Monti, D

2000-12-15

The purpose of this study was 1) to assess the effect of zolpidem or a placebo on sleep in two groups of insomniac patients with a diagnosis of moderate-to-severe chronic primary insomnia and 2) to determine the effect of zolpidem on sleep structure using spectral analysis. A randomized, double-blind, placebo-controlled trial. Sleep laboratory of the Department of Pharmacology and Therapeutics at the Clinics Hospital. 12 female outpatients with chronic primary insomnia. Zolpidem was given at a daily dose of 10 mg for 15 nights. The hypnotic drug reduced sleep latency and waking time after sleep onset, and increased total sleep time and sleep efficiency. Values corresponding to visually scored slow wave sleep (stage 3 and 4) showed no significant changes. All-night spectral analysis of the EEG revealed that power density in NREM sleep was significantly increased in the low frequency band (0.25-1.0 Hz) in the zolpidem group during the first 2-h interval. In agreement with previous findings obtained in patients with chronic primary insomnia, zolpidem significantly improved sleep induction and maintenance. Moreover, zolpidem increased power density in the 0.25-1.0 Hz band during short-term and intermediate-term treatment. Nevertheless, other frequency bands in the delta range showed a relative decrease which was not statistically significant.

Power Balance and Impurity Studies in TCS

NASA Astrophysics Data System (ADS)

Grossnickle, J. A.; Pietrzyk, Z. A.; Vlases, G. C.

2003-10-01

A "zero-dimension" power balance model was developed based on measurements of absorbed power, radiated power, absolute D_α, temperature, and density for the TCS device. Radiation was determined to be the dominant source of power loss for medium to high density plasmas. The total radiated power was strongly correlated with the Oxygen line radiation. This suggests Oxygen is the dominant radiating species, which was confirmed by doping studies. These also extrapolate to a Carbon content below 1.5%. Determining the source of the impurities is an important question that must be answered for the TCS upgrade. Preliminary indications are that the primary sources of Oxygen are the stainless steel end cones. A Ti gettering system is being installed to reduce this Oxygen source. A field line code has been developed for use in tracking where open field lines terminate on the walls. Output from this code is also used to generate grids for an impurity tracking code.

Hypermineralization and High Osteocyte Lacunar Density in Osteogenesis Imperfecta Type V Bone Indicate Exuberant Primary Bone Formation.

PubMed

Blouin, Stéphane; Fratzl-Zelman, Nadja; Glorieux, Francis H; Roschger, Paul; Klaushofer, Klaus; Marini, Joan C; Rauch, Frank

2017-09-01

In contrast to "classical" forms of osteogenesis imperfecta (OI) types I to IV, caused by a mutation in COL1A1/A2, OI type V is due to a gain-of-function mutation in the IFITM5 gene, encoding the interferon-induced transmembrane protein 5, or bone-restricted interferon-inducible transmembrane (IFITM)-like protein (BRIL). Its phenotype distinctly differs from OI types I to IV by absence of blue sclerae and dentinogenesis imperfecta, by the occurrence of ossification disorders such as hyperplastic callus and forearm interosseous membrane ossification. Little is known about the impact of the mutation on bone tissue/material level in untreated and bisphosphonate-treated patients. Therefore, investigations of transiliac bone biopsy samples from a cohort of OI type V children (n = 15, 8.7 ± 4 years old) untreated at baseline and a subset (n = 8) after pamidronate treatment (2.6 years in average) were performed. Quantitative backscattered electron imaging (qBEI) was used to determine bone mineralization density distribution (BMDD) as well as osteocyte lacunar density. The BMDD of type V OI bone was distinctly shifted toward a higher degree of mineralization. The most frequently occurring calcium concentration (CaPeak) in cortical (Ct) and cancellous (Cn) bone was markedly increased (+11.5%, +10.4%, respectively, p < 0.0001) compared to healthy reference values. Treatment with pamidronate resulted in only a slight enhancement of mineralization. The osteocyte lacunar density derived from sectioned bone area was elevated in OI type V Ct and Cn bone (+171%, p < 0.0001; +183.3%, p < 0.01; respectively) versus controls. The high osteocyte density was associated with an overall immature primary bone structure ("mesh-like") as visualized by polarized light microscopy. In summary, the bone material from OI type V patients is hypermineralized, similar to other forms of OI. The elevated osteocyte lacunar density in connection with lack of regular bone lamellation points to an exuberant primary bone formation and an alteration of the bone remodeling process in OI type V. © 2017 American Society for Bone and Mineral Research. © 2017 American Society for Bone and Mineral Research.

Breast cancer screening in the era of density notification legislation: summary of 2014 Massachusetts experience and suggestion of an evidence-based management algorithm by multi-disciplinary expert panel.

PubMed

Freer, Phoebe E; Slanetz, Priscilla J; Haas, Jennifer S; Tung, Nadine M; Hughes, Kevin S; Armstrong, Katrina; Semine, A Alan; Troyan, Susan L; Birdwell, Robyn L

2015-09-01

Stemming from breast density notification legislation in Massachusetts effective 2015, we sought to develop a collaborative evidence-based approach to density notification that could be used by practitioners across the state. Our goal was to develop an evidence-based consensus management algorithm to help patients and health care providers follow best practices to implement a coordinated, evidence-based, cost-effective, sustainable practice and to standardize care in recommendations for supplemental screening. We formed the Massachusetts Breast Risk Education and Assessment Task Force (MA-BREAST) a multi-institutional, multi-disciplinary panel of expert radiologists, surgeons, primary care physicians, and oncologists to develop a collaborative approach to density notification legislation. Using evidence-based data from the Institute for Clinical and Economic Review, the Cochrane review, National Comprehensive Cancer Network guidelines, American Cancer Society recommendations, and American College of Radiology appropriateness criteria, the group collaboratively developed an evidence-based best-practices algorithm. The expert consensus algorithm uses breast density as one element in the risk stratification to determine the need for supplemental screening. Women with dense breasts and otherwise low risk (<15% lifetime risk), do not routinely require supplemental screening per the expert consensus. Women of high risk (>20% lifetime) should consider supplemental screening MRI in addition to routine mammography regardless of breast density. We report the development of the multi-disciplinary collaborative approach to density notification. We propose a risk stratification algorithm to assess personal level of risk to determine the need for supplemental screening for an individual woman.

Environmental conditions and biotic interactions influence ecosystem structure and function in a drying stream

USGS Publications Warehouse

Ludlam, J.P.; Magoulick, D.D.

2010-01-01

Benthic consumers influence stream ecosystem structure and function, but these interactions depend on environmental context. We experimentally quantified the effects of central stoneroller minnows (Campostoma anomalum (Rafinesque) and Meek's crayfish (Orconectes meeki meeki (Faxon)) on benthic communities using electric exclusion quadrats in Little Mulberry Creek before (June) and during (August) seasonal stream drying. Unglazed ceramic tiles were deployed in June and August to measure periphyton and invertebrate abundance, and leafpack decomposition and primary production were also measured in August. Relationships between stoneroller and crayfish density and the size of consumer effects were evaluated with multiple linear regression models. Average chlorophyll a abundance was greater on exposed than exclusion tiles in August, but not in June. Sediment dry mass, periphyton ash-free dry mass (AFDM), and chironomid densities on tiles did not differ among treatments in either period. Leaf packs decayed faster in exposed than exclusion treatments (kexposed = 0.038 ?? 0.013, kexclusion = 0.007 ?? 0.002), but consumer effects were stronger in some pools than others. Leafpack invertebrate biomass and abundance and tile primary productivity did not differ among treatments. Consumer effects on chlorophyll a were related to crayfish and stoneroller density, and effects on chironomid density were related to stoneroller density. These results contrast with a previous exclusion experiment in Little Mulberry Creek that demonstrated strong consumer effects. The influence of stream drying on consumer effects appears to have been reduced by strong spates, underscoring the importance of conducting multi-year studies to determine the magnitude of variability in ecological interactions. ?? US Government: USGS 2010.

Probing M Dwarf Model-Data Discrepancies via Precise, Empirical Characterization of a Long-Period F+M Binary

NASA Astrophysics Data System (ADS)

Stevens, Daniel; Gaudi, Scott; Beatty, Thomas; Siverd, Robert

2018-05-01

Double-lined eclipsing binaries (EBs) have been the gold standard for direct, precise (less than a few percent), and accurate measurements of stellar masses and radii. However, with the availability of Gaia parallaxes and nearly complete spectral energy distributions (SEDs) of millions of stars, it will soon be possible to make such measurements for the much larger number of single-lined EBs such as high mass-ratio systems and transiting planets, both of which are routinely found by transit surveys. Combining high-precision eclipse photometry and radial velocity (RV) observations of the primary star enables measurements of the primary star's density, the ratio of stellar radii, and a combination of the stars' masses. Broad-band photometry from the ultraviolet to the infrared plus a Gaia parallax and an effective temperature of the primary from either the SED or high-resolution spectra, allow one to measure the radius (and mass via the density) of the primary. The radius and mass of the secondary can then be determined in the usual way with the radius ratio and RVs, and the companion's effective temperature can be determined from a secondary eclipse measurement and the primary star's effective temperature. For single-lined EBs, the precision of ingress/egress duration measurements dominates the error budget of the masses and companion radius. We propose to observe one primary and secondary eclipse of the F+M binary TYC 4223-1012-1, an M dwarf on a 16.5-day orbit around an F dwarf. Ground-based data poorly constrain TYC 4223-1012-1's masses due to the near-impossibility of observing the full 10-hr eclipse from the ground. By combining extant RV and SED data with the Spitzer data, we expect to measure the mass, radius, and effective temperature of the M dwarf to a few percent. This is comparable to the precision of the best-characterized literature M dwarfs, but at an orbital period far beyond the majority of such systems, where tidal effects should be negligible.

Effects of vial packing density on drying rate during freeze-drying of carbohydrates or a model protein measured using a vial-weighing technique.

PubMed

Gieseler, Henning; Lee, Geoffrey

2008-02-01

To determine the effects of vial packing density in a laboratory freeze dryer on drying rate profiles of crystalline and amorphous formulations. The Christ freeze-drying balance measured cumulative water loss, m(t), and instantaneous drying rate, m(t), of water, mannitol, sucrose and sucrose/BSA formulations in commercial vials. Crystalline mannitol shows drying rate behaviour indicative of a largely homogeneous dried-product layer. The drying rate behaviour of amorphous sucrose indicates structural heterogeneity, postulated to come from shrinkage or microcollapse. Trehalose dries more slowly than sucrose. Addition of BSA to either disaccharide decreases primary drying time. Higher vial packing density greatly reduces drying rate because of effects of radiation heat transfer from chamber walls to test vial. Plots of m(t) versus radical t and m(t) versus layer thickness (either ice or dried-product) allow interpretation of changes in internal cake morphology during drying. Vial packing density greatly influences these profiles.

Conductance based characterization of structure and hopping site density in 2D molecule-nanoparticle arrays

NASA Astrophysics Data System (ADS)

McCold, Cliff E.; Fu, Qiang; Howe, Jane Y.; Hihath, Joshua

2015-09-01

Composite molecule-nanoparticle hybrid systems have recently emerged as important materials for applications ranging from chemical sensing to nanoscale electronics. However, creating reproducible and repeatable composite materials with precise properties has remained one of the primary challenges to the implementation of these technologies. Understanding the sources of variation that dominate the assembly and transport behavior is essential for the advancement of nanoparticle-array based devices. In this work, we use a combination of charge-transport measurements, electron microscopy, and optical characterization techniques to determine the role of morphology and structure on the charge transport properties of 2-dimensional monolayer arrays of molecularly-interlinked Au nanoparticles. Using these techniques we are able to determine the role of both assembly-dependent and particle-dependent defects on the conductivities of the films. These results demonstrate that assembly processes dominate the dispersion of conductance values, while nanoparticle and ligand features dictate the mean value of the conductance. By performing a systematic study of the conductance of these arrays as a function of nanoparticle size we are able to extract the carrier mobility for specific molecular ligands. We show that nanoparticle polydispersity correlates with the void density in the array, and that because of this correlation it is possible to accurately determine the void density within the array directly from conductance measurements. These results demonstrate that conductance-based measurements can be used to accurately and non-destructively determine the morphological and structural properties of these hybrid arrays, and thus provide a characterization platform that helps move 2-dimensional nanoparticle arrays toward robust and reproducible electronic systems.Composite molecule-nanoparticle hybrid systems have recently emerged as important materials for applications ranging from chemical sensing to nanoscale electronics. However, creating reproducible and repeatable composite materials with precise properties has remained one of the primary challenges to the implementation of these technologies. Understanding the sources of variation that dominate the assembly and transport behavior is essential for the advancement of nanoparticle-array based devices. In this work, we use a combination of charge-transport measurements, electron microscopy, and optical characterization techniques to determine the role of morphology and structure on the charge transport properties of 2-dimensional monolayer arrays of molecularly-interlinked Au nanoparticles. Using these techniques we are able to determine the role of both assembly-dependent and particle-dependent defects on the conductivities of the films. These results demonstrate that assembly processes dominate the dispersion of conductance values, while nanoparticle and ligand features dictate the mean value of the conductance. By performing a systematic study of the conductance of these arrays as a function of nanoparticle size we are able to extract the carrier mobility for specific molecular ligands. We show that nanoparticle polydispersity correlates with the void density in the array, and that because of this correlation it is possible to accurately determine the void density within the array directly from conductance measurements. These results demonstrate that conductance-based measurements can be used to accurately and non-destructively determine the morphological and structural properties of these hybrid arrays, and thus provide a characterization platform that helps move 2-dimensional nanoparticle arrays toward robust and reproducible electronic systems. Electronic supplementary information (ESI) available: Temperature dependent measurements, activation energies, particle size distributions, void density-polydispersity relation, and DLS data. See DOI: 10.1039/c5nr04460j

The effect of primary hyperparathyroidism on pancreatic exocrine function.

PubMed

Sisman, P; Avci, M; Akkurt, A; Sahin, A B; Gul, O O; Ersoy, C; Erturk, E

2018-03-01

Elastase-1 is a proteolytic enzyme secreted by pancreatic acinar cells, and measurements of the concentration this enzyme are used to evaluate pancreatic exocrine function. We aimed to determine whether pancreatic exocrine function declines due to chronic hypercalcemia by measuring fecal elastase levels. 75 patients with primary hyperparathyroidism (18 men and 47 women) and 30 healthy subjects (11 men and 19 women) participated in this study. Renal function tests, lipid parameters, bone mineral density, and serum calcium, phosphorus, vitamin D, parathormone, glucose, and thyroid stimulating hormone levels as well as fecal elastase concentrations, were determined in these patients and controls. The mean fecal elastase level was 335.3 ± 181.4 μg/g in the PHPT group and 317.4 ± 157.3 μg/g in the control group. There was no significant difference in fecal elastase levels between the two groups (p = 0.5). Chronic hypercalcemia in primary hyperparathyroidism did not decrease the fecal elastase level, which is an indirect indicator of chronic pancreatitis; therefore, chronic hypercalcemia in PHPT may not cause chronic pancreatitis.

Non-Invasive Markers of Tumor Growth, Metastases, and Sensitivity to Anti-Neoplastic Therapy

DTIC Science & Technology

2009-01-01

angiogenic agents. Validation of the results of the treatment studies will be based on tumor growth, metastases, and microvessel density...detectable by NMR. DCE-MRI studies do not suggest differences in vascular parameters between slow and fast growing rat prostate tumors. The R3327AT...Introduction The primary goal of this study is to determine whether non-invasive magnetic resonance (MR) techniques can distinguish between slow and

Prognostic significance of microvessel density and mast cell density for the survival of Thai patients with primary colorectal cancer.

PubMed

Yodavudh, Sirisanpang; Tangjitgamol, Siriwan; Puangsa-art, Supalarp

2008-05-01

Angiogenesis has been found to be a reliable prognostic indicator for several types of malignancies. In colorectal cancer, however there has been controversy as to whether there is a correlation between this feature and the tumors' behavior. Determine the correlation between microvessel density (MVD) and mast cell density (MCD) in order to evaluate these factors in terms of their prognostic relevance for primary colorectal carcinoma in Thai patients. One hundred and thirty colorectal carcinoma patients diagnosed between January 2002 and December 2004 were identified. Eleven patients were excluded from the present study due to recurrence of colorectal carcinoma in eight cases whereas pathologic blocks were not found in three cases. One hundred and nineteen patients met all inclusion criteria and were included in the present study. Representative paraffin sections obtained by the tissue micro-array technique (9 x 5 arrays per slide) from areas of highest vascular density (hot spots) were prepared. Sections were immuno-stained by monoclonal anti CD 31 for microvessel and antibody mast cell tryptase for mast cell detections, respectively. Three readings at different periods of time under a microscopic examination of high power magnification were examined by a pathologist who was blinded to clinical data. The highest microvessel and mast cell counts were recorded as MVD and MCD. Patients were then divided into groups of high and low MVD and high and low MCD by median values (20.5 and 14.5, respectively). Overall survival of the patients in each group was estimated by the Kaplan-Meier Method while a multivariate Cox regression backward stepwise analysis was employed to find out independent prognostic factors. Significant positive correlation was found to exist between MVD and MCD in the hot spots (R = 0.697, p < 0.0001). Regarding their prognostic role, patients with tumors of low MVD (hypovascular) and low MCD (low mast cell counts) had significantly longer survival rates than those with hypervascular and high mast cell counts (p < 0.0001). The Multivariate Cox hazard showed that MVD and distance metastasis of cancer were independent poor prognostic factors to survival (p = 0.036 and p = 0.024, respectively). The patients with high MVD (hypervascular) tumors and with presence of distant metastasis had 1.9 and 2.5 times higher death rates than the corresponding hypovascular and non-metastatic groups, respectively during the period from January 2002 to September 2007. Assessment of microvessel density in the invasive front of primary colorectal carcinoma could serve as useful prognosis tool of primary colorectal carcinoma in Thai patients.

The dynamics of pico-sized and bloom-forming cyanobacteria in large water bodies in the Mekong River Basin

PubMed Central

Tomioka, Noriko; Jutagate, Tuantong; Hiroki, Mikiya; Murata, Tomoyoshi; Preecha, Chatchai; Avakul, Piyathap; Phomikong, Pisit; Imai, Akio

2017-01-01

In the face of plans for increased construction of dams and reservoirs in the Mekong River Basin, it is critically important to better understand the primary-producer community of phytoplankton, especially the warm-water cyanobacteria. This is because these algae can serve as the primary source of carbon for higher trophic levels, including fishes, but can also form harmful blooms, threatening local fisheries and environmental and human health. We monitored the dynamics of three cyanobacteria—Synechococcus spp., Microcystis aeruginosa, and Dolichospermum spp.—for two years in nine large lakes and reservoirs in the Mekong River Basin. The densities of these algae were largely system-specific such that their abundance was uniquely determined within individual water bodies. However, after accounting for the system-specific effect, we found that cell densities of Synechococcus spp., M. aeruginosa, and Dolichospermum spp. varied in response to changes in photosynthetically active radiation (PAR), total nitrogen, and water level, respectively. Because both PAR and water level tend to fluctuate concordantly over a wide geographic area, Synechococcus spp., and to a lesser extent Dolichospermum spp., varied synchronously among the water bodies. Sustaining the production of pico-sized primary producers while preventing harmful algal blooms will be a key management goal for the proposed reservoirs in the Mekong Basin. PMID:29272288

Influences of human and livestock density on winter habitat selection of Mongolian gazelle (Procapra gutturosa).

PubMed

Luo, Zhenhua; Liu, Bingwan; Liu, Songtao; Jiang, Zhigang; Halbrook, Richard S

2014-01-01

Human and livestock related disturbances of habitat selection by ungulates are topics of global concern, as they have profound impacts on ungulate survival, population density, fitness, and management; however, differences in ungulate habitat use under different human and livestock densities are not fully understood. Mongolian gazelle (Procapra gutturosa), an endemic ungulate species on the Asia-European steppe, faces varying intensities of human and livestock disturbances in the area around Dalai Lake, China. To investigate how habitat selection strategies vary as disturbance intensity changes, we randomly set 20 transects containing 1486 plots, on which we conducted repeated surveys of 21 ecological factors during the winters in the period of 2005-2008. We aimed to: 1) determine the critical factors underlying habitat selection of the gazelles; 2) determine the gazelles' habitat preferences in this area; 3) determine how habitat selection varies with disturbance intensity and explore the primary underlying mechanism. We used binary-logistic regressions and information theoretic approaches to build best-fit habitat selection models, and calculated resource selection functions. Sixty-six herds, 522 individuals, and 499 tracks were recorded. Our results indicate that snow depth and aboveground biomass are the main factors affecting habitat selection by Mongolian gazelle throughout the district in winter. Thin snow cover and abundant aboveground biomass are preferred. Avoiding disturbance was the primary factor accounting for habitat selection in low disturbance areas, although with increasing human or live-stock-related disturbance, gazelle maintained a reduced distance to the source of the disturbance. Presumably owing to that shift, movement costs were more important as disturbance increased. In addition, Mongolian gazelle selected habitats based on topographical features promoting greater visibility where disturbance was lower. We suggest several management implications of our findings for this ungulate species will contribute to the effective conservation of Mongolian gazelle in the Dalai Lake area.

Non-Linear Interactions between Consumers and Flow Determine the Probability of Plant Community Dominance on Maine Rocky Shores

PubMed Central

Silliman, Brian R.; McCoy, Michael W.; Trussell, Geoffrey C.; Crain, Caitlin M.; Ewanchuk, Patrick J.; Bertness, Mark D.

2013-01-01

Although consumers can strongly influence community recovery from disturbance, few studies have explored the effects of consumer identity and density and how they may vary across abiotic gradients. On rocky shores in Maine, recent experiments suggest that recovery of plant- or animal- dominated community states is governed by rates of water movement and consumer pressure. To further elucidate the mechanisms of consumer control, we examined the species-specific and density-dependent effects of rocky shore consumers (crabs and snails) on community recovery under both high (mussel dominated) and low flow (plant dominated) conditions. By partitioning the direct impacts of predators (crabs) and grazers (snails) on community recovery across a flow gradient, we found that grazers, but not predators, are likely the primary agent of consumer control and that their impact is highly non-linear. Manipulating snail densities revealed that herbivorous and bull-dozing snails (Littorina littorea) alone can control recovery of high and low flow communities. After ∼1.5 years of recovery, snail density explained a significant amount of the variation in macroalgal coverage at low flow sites and also mussel recovery at high flow sites. These density-dependent grazer effects were were both non-linear and flow-dependent, with low abundance thresholds needed to suppress plant community recovery, and much higher levels needed to control mussel bed development. Our study suggests that consumer density and identity are key in regulating both plant and animal community recovery and that physical conditions can determine the functional forms of these consumer effects. PMID:23940510

Bone density and functional results after femoral revision with a cementless press-fit stem.

PubMed

Canovas, F; Roche, O; Girard, J; Bonnomet, F; Goldschild, M; Le Béguec, P

2015-05-01

The influence of radiographic bone density changes in the area surrounding a total hip arthroplasty (THA) revision with a cementless press-fit stem is unknown, notably in terms of functional results. We have therefore conducted a study aiming to (1) propose a radiographic method to assess bone density, (2) measure the functional effects of reduced bone density, and (3) determine the factors contributing to these modifications. A reduction in radiographic bone density has a negative influence on the functional result after revision using a cementless press-fit stem. We retrospectively assessed 150 THA revisions at a mean follow-up of 6.3 ± 3.2 years (range, 2-15 years). The clinical assessment was based on the Harris Hip Score. Bone density modifications were measured radiographically and the method was evaluated. The change in bone density was classified into two groups: (1) bone density not reduced or < 2 Gruen zones (118 cases [79%]); (2) bone density reduced ≥ 2 zones (32 cases [21%]). The variables showing a potential influence were the Cortical Index (CI), the type of primary stability with the press-fit system, and the femoral implant length. Inter- and intraobserver reliability of radiographic bone density measurement was evaluated as moderate or good (Kappa, 0.58; 0.60 and 0.67, respectively). For the Harris Hip Score at follow-up, there was a borderline statistical relation between stages 1 and 2: for the 118 stage 1 patients, this score was 83.62 ± 11.54 (range, 27-99) versus 78.34 ± 15.98 (range, 62-91) for stage 2 patients (P = 0.09). A CI ≤ 0.44 showed mediocre bone quality contributing to decreased bone density (P < 0.02). On the other hand, there was no statistically significant relation with the type of primary fixation (P = 0.34) or the length of the implant (P = 0.23). A cementless revision femoral stem can induce a reduction in bone density with possible functional effects. The negative role played by bone scarcity on the functional score is confirmed, and even though the difference is not statistically significant, we suggest using a short stem when this is possible. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Breast Cancer Screening in the Era of Density Notification Legislation: Summary of 2014 Massachusetts Experience and Suggestion of An Evidence-Based Management Algorithm by Multi-disciplinary Expert Panel

PubMed Central

Freer, Phoebe E.; Slanetz, Priscilla J.; Haas, Jennifer S.; Tung, Nadine M.; Hughes, Kevin S.; Armstrong, Katrina; Semine, A. Alan; Troyan, Susan L.; Birdwell, Robyn L.

2015-01-01

Purpose Stemming from breast density notification legislation in Massachusetts effective 2015, we sought to develop a collaborative evidence-based approach to density notification that could be used by practitioners across the state. Our goal was to develop an evidence-based consensus management algorithm to help patients and health care providers follow best practices to implement a coordinated, evidence-based, cost-effective, sustainable practice and to standardize care in recommendations for supplemental screening. Methods We formed the Massachusetts Breast Risk Education and Assessment Task Force (MA-BREAST) a multi-institutional, multi-disciplinary panel of expert radiologists, surgeons, primary care physicians, and oncologists to develop a collaborative approach to density notification legislation. Using evidence-based data from the Institute for Clinical and Economic Review (ICER), the Cochrane review, National Comprehensive Cancer Network (NCCN) guidelines, American Cancer Society (ACS) recommendations, and American College of Radiology (ACR) appropriateness criteria, the group collaboratively developed an evidence-based best-practices algorithm. Results The expert consensus algorithm uses breast density as one element in the risk stratification to determine the need for supplemental screening. Women with dense breasts and otherwise low risk (<15% lifetime risk), do not routinely require supplemental screening per the expert consensus. Women of high risk (>20% lifetime) should consider supplemental screening MRI in addition to routine mammography regardless of breast density. Conclusion We report the development of the multi-disciplinary collaborative approach to density notification. We propose a risk stratification algorithm to assess personal level of risk to determine the need for supplemental screening for an individual woman. PMID:26290416

Cell wall microstructure, pore size distribution and absolute density of hemp shiv

PubMed Central

Lawrence, M.; Ansell, M. P.; Hussain, A.

2018-01-01

This paper, for the first time, fully characterizes the intrinsic physical parameters of hemp shiv including cell wall microstructure, pore size distribution and absolute density. Scanning electron microscopy revealed microstructural features similar to hardwoods. Confocal microscopy revealed three major layers in the cell wall: middle lamella, primary cell wall and secondary cell wall. Computed tomography improved the visualization of pore shape and pore connectivity in three dimensions. Mercury intrusion porosimetry (MIP) showed that the average accessible porosity was 76.67 ± 2.03% and pore size classes could be distinguished into micropores (3–10 nm) and macropores (0.1–1 µm and 20–80 µm). The absolute density was evaluated by helium pycnometry, MIP and Archimedes' methods. The results show that these methods can lead to misinterpretation of absolute density. The MIP method showed a realistic absolute density (1.45 g cm−3) consistent with the density of the known constituents, including lignin, cellulose and hemi-cellulose. However, helium pycnometry and Archimedes’ methods gave falsely low values owing to 10% of the volume being inaccessible pores, which require sample pretreatment in order to be filled by liquid or gas. This indicates that the determination of the cell wall density is strongly dependent on sample geometry and preparation. PMID:29765652

Cell wall microstructure, pore size distribution and absolute density of hemp shiv

NASA Astrophysics Data System (ADS)

Jiang, Y.; Lawrence, M.; Ansell, M. P.; Hussain, A.

2018-04-01

This paper, for the first time, fully characterizes the intrinsic physical parameters of hemp shiv including cell wall microstructure, pore size distribution and absolute density. Scanning electron microscopy revealed microstructural features similar to hardwoods. Confocal microscopy revealed three major layers in the cell wall: middle lamella, primary cell wall and secondary cell wall. Computed tomography improved the visualization of pore shape and pore connectivity in three dimensions. Mercury intrusion porosimetry (MIP) showed that the average accessible porosity was 76.67 ± 2.03% and pore size classes could be distinguished into micropores (3-10 nm) and macropores (0.1-1 µm and 20-80 µm). The absolute density was evaluated by helium pycnometry, MIP and Archimedes' methods. The results show that these methods can lead to misinterpretation of absolute density. The MIP method showed a realistic absolute density (1.45 g cm-3) consistent with the density of the known constituents, including lignin, cellulose and hemi-cellulose. However, helium pycnometry and Archimedes' methods gave falsely low values owing to 10% of the volume being inaccessible pores, which require sample pretreatment in order to be filled by liquid or gas. This indicates that the determination of the cell wall density is strongly dependent on sample geometry and preparation.

Lymphocyte density determined by computational pathology validated as a predictor of response to neoadjuvant chemotherapy in breast cancer: secondary analysis of the ARTemis trial.

PubMed

Ali, H R; Dariush, A; Thomas, J; Provenzano, E; Dunn, J; Hiller, L; Vallier, A-L; Abraham, J; Piper, T; Bartlett, J M S; Cameron, D A; Hayward, L; Brenton, J D; Pharoah, P D P; Irwin, M J; Walton, N A; Earl, H M; Caldas, C

2017-08-01

We have previously shown lymphocyte density, measured using computational pathology, is associated with pathological complete response (pCR) in breast cancer. The clinical validity of this finding in independent studies, among patients receiving different chemotherapy, is unknown. The ARTemis trial randomly assigned 800 women with early stage breast cancer between May 2009 and January 2013 to three cycles of docetaxel, followed by three cycles of fluorouracil, epirubicin and cyclophosphamide once every 21 days with or without four cycles of bevacizumab. The primary endpoint was pCR (absence of invasive cancer in the breast and lymph nodes). We quantified lymphocyte density within haematoxylin and eosin (H&E) whole slide images using our previously described computational pathology approach: for every detected lymphocyte the average distance to the nearest 50 lymphocytes was calculated and the density derived from this statistic. We analyzed both pre-treatment biopsies and post-treatment surgical samples of the tumour bed. Of the 781 patients originally included in the primary endpoint analysis of the trial, 609 (78%) were included for baseline lymphocyte density analyses and a subset of 383 (49% of 781) for analyses of change in lymphocyte density. The main reason for loss of patients was the availability of digitized whole slide images. Pre-treatment lymphocyte density modelled as a continuous variable was associated with pCR on univariate analysis (odds ratio [OR], 2.92; 95% CI, 1.78-4.85; P < 0.001) and after adjustment for clinical covariates (OR, 2.13; 95% CI, 1.24-3.67; P = 0.006). Increased pre- to post-treatment lymphocyte density showed an independent inverse association with pCR (adjusted OR, 0.1; 95% CI, 0.033-0.31; P < 0.001). Lymphocyte density in pre-treatment biopsies was validated as an independent predictor of pCR in breast cancer. Computational pathology is emerging as a viable and objective means of identifying predictive biomarkers for cancer patients. NCT01093235. © The Author 2017. Published by Oxford University Press on behalf of the European Society for Medical Oncology.

All-In-One: Advanced preparation of Human Parenchymal and Non-Parenchymal Liver Cells.

PubMed

Werner, Melanie; Driftmann, Sabrina; Kleinehr, Kathrin; Kaiser, Gernot M; Mathé, Zotlan; Treckmann, Juergen-Walter; Paul, Andreas; Skibbe, Kathrin; Timm, Joerg; Canbay, Ali; Gerken, Guido; Schlaak, Joerg F; Broering, Ruth

2015-01-01

Liver cells are key players in innate immunity. Thus, studying primary isolated liver cells is necessary for determining their role in liver physiology and pathophysiology. In particular, the quantity and quality of isolated cells are crucial to their function. Our aim was to isolate a large quantity of high-quality human parenchymal and non-parenchymal cells from a single liver specimen. Hepatocytes, Kupffer cells, liver sinusoidal endothelial cells, and stellate cells were isolated from liver tissues by collagenase perfusion in combination with low-speed centrifugation, density gradient centrifugation, and magnetic-activated cell sorting. The purity and functionality of cultured cell populations were controlled by determining their morphology, discriminative cell marker expression, and functional activity. Cell preparation yielded the following cell counts per gram of liver tissue: 2.0 ± 0.4 × 10(7) hepatocytes, 1.8 ± 0.5 × 10(6 )Kupffer cells, 4.3 ± 1.9 × 10(5) liver sinusoidal endothelial cells, and 3.2 ± 0.5 × 10(5) stellate cells. Hepatocytes were identified by albumin (95.5 ± 1.7%) and exhibited time-dependent activity of cytochrome P450 enzymes. Kupffer cells expressed CD68 (94.5 ± 1.2%) and exhibited phagocytic activity, as determined with 1 μm latex beads. Endothelial cells were CD146(+) (97.8 ± 1.1%) and exhibited efficient uptake of acetylated low-density lipoprotein. Hepatic stellate cells were identified by the expression of α-smooth muscle actin (97.1 ± 1.5%). These cells further exhibited retinol (vitamin A)-mediated autofluorescence. Our isolation procedure for primary parenchymal and non-parenchymal liver cells resulted in cell populations of high purity and quality, with retained physiological functionality in vitro. Thus, this system may provide a valuable tool for determining liver function and disease.

Variable residence time vortex combustor

DOEpatents

Melconian, Jerry O.

1987-01-01

A variable residence time vortex combustor including a primary combustion chamber for containing a combustion vortex, and a plurality of louvres peripherally disposed about the primary combustion chamber and longitudinally distributed along its primary axis. The louvres are inclined to impel air about the primary combustion chamber to cool its interior surfaces and to impel air inwardly to assist in driving the combustion vortex in a first rotational direction and to feed combustion in the primary combustion chamber. The vortex combustor also includes a second combustion chamber having a secondary zone and a narrowed waist region in the primary combustion chamber interconnecting the output of the primary combustion chamber with the secondary zone for passing only lower density particles and trapping higher density particles in the combustion vortex in the primary combustion chamber for substantial combustion.

Influence of arthritis and non-arthritis related factors on areal bone mineral density (BMDa) in women with longstanding inflammatory polyarthritis: a primary care based inception cohort.

PubMed

Pye, Stephen R; Marshall, Tarnya; Gaffney, Karl; Silman, Alan J; Symmons, Deborah P M; O'Neill, Terence W

2010-05-28

The aim of this analysis was to determine the relative influence of disease and non-disease factors on areal bone mineral density (BMDa) in a primary care based cohort of women with inflammatory polyarthritis. Women aged 16 years and over with recent onset inflammatory polyarthritis were recruited to the Norfolk Arthritis Register (NOAR) between 1990 and 1993. Subjects were examined at both baseline and follow up for the presence of tender, swollen and deformed joints. At the 10th anniversary visit, a sub-sample of women were invited to complete a bone health questionnaire and attend for BMDa (Hologic, QDR 4000). Linear regression was used to examine the association between BMDa with both (i) arthritis-related factors assessed at baseline and the 10th anniversary visit and (ii) standard risk factors for osteoporosis. Adjustments were made for age. 108 women, mean age 58.0 years were studied. Older age, decreasing weight and BMI at follow up were all associated with lower BMDa at both the spine and femoral neck. None of the lifestyle factors were linked. Indices of joint damage including 10th anniversary deformed joint count and erosive joint count were the arthritis-related variables linked with a reduction in BMDa at the femoral neck. By contrast, disease activity as determined by the number of tender and or swollen joints assessed both at baseline and follow up was not linked with BMDa at either site. Cumulative disease damage was the strongest predictor of reduced femoral bone density. Other disease and lifestyle factors have only a modest influence.

Estrogens and women's health: interrelation of coronary heart disease, breast cancer and osteoporosis.

PubMed

Kuller, L H; Matthews, K A; Meilahn, E N

2000-11-30

The determinants of blood levels of estrogen, estrogen metabolites, and relation to receptors and post-transitional effects are the likely primary cause of breast cancer. Very high risk women for breast cancer can now be identified by measuring bone mineral density and hormone levels. These high risk women have rates of breast cancer similar to risk of myocardial infarction. They are candidates for SERM therapies to reduce risk of breast cancer. The completion of the Women's Health Initiative and other such trials will likely provide a definite association of risk and benefit of both estrogen alone and estrogen-progesterone therapy, coronary heart disease, osteoporotic fracture, and breast cancer. The potential intervention of hormone replacement therapy, obesity, or weight gain and increased atherogenic lipoproteinemia may be of concern and confound the results of clinical trials. Estrogens, clearly, are important in the risk of bone loss and osteoporotic fracture. Obesity is the primary determinant of postmenopausal estrogen levels and reduced risk of fracture. Weight reduction may increase rates of bone loss and fracture. Clinical trials that evaluate weight loss should monitor effects on bone. The beneficial addition of increased physical activity, higher dose of calcium or vitamin D, or use of bone reabsorption drugs in coordination with weight loss should be evaluated. Any therapy that raises blood estrogen or metabolite activity and decreases bone loss may increase risk of breast cancer. Future clinical trials must evaluate multiple endpoints such as CHD, osteoporosis, and breast cancer within the study. The use of surrogate markers such as bone mineral density, coronary calcium, carotid intimal medial thickness and plaque, endothelial function, breast density, hormone levels and metabolites could enhance the evaluation of risk factors, genetic-environmental intervention, and new therapies.

Experimental analysis of insertion torques and forces of threaded and press-fit acetabular cups by means of ex vivo and in vivo measurements.

PubMed

Vogel, Danny; Rathay, Andreas; Teufel, Stephanie; Ellenrieder, Martin; Zietz, Carmen; Sander, Manuela; Bader, Rainer

2017-01-01

In THA a sufficient primary implant stability is the precondition for successful secondary stability. Industrial foams of different densities have been used for primary stability investigations. The aim of this study was to analyse and compare the insertion behaviour of threaded and press-fit cups in vivo and ex vivo using bone substitutes with various densities. Two threaded (Bicon Plus®, Trident® TC) and one press-fit cup (Trident PSL®) were inserted by orthopaedic surgeons (S1, S2) into 10, 20 and 31 pcf blocks, using modified surgical instruments allowing measurements of the insertion forces and torques. Furthermore, the insertion behaviour of two cups were analysed intraoperatively. Torques for the threaded cups increased while bone substitute density increased. Maximum insertion torques were observed for S2 with 102 Nm for the Bicon Plus® in 20 pcf blocks and 77 Nm for the Trident® TC in 31 pcf blocks, which compares to the in vivo measurement (85 Nm). The average insertion forces for the press-fit cup varied from 5.2 to 6.8 kN (S1) and 7.2-11.5 kN (S2) ex vivo. Intraoperatively an average insertion force of 8.0 kN was determined. Implantation behaviour was influenced by acetabular cup design, bone substitute and experience of the surgeon. No specific density of bone substitute could be favoured for ex vivo investigations on the implantation behaviour of acetabular cups. The use synthetic bone blocks of high density (31 pcf) led to problems regarding cup orientation and seating. Therefore, bone substitutes used should be critically scrutinized in terms of the comparability to the in vivo situation.

Immunoscore encompassing CD3+ and CD8+ T cell densities in distant metastasis is a robust prognostic marker for advanced colorectal cancer

PubMed Central

Kwak, Yoonjin; Koh, Jiwon; Kim, Duck-Woo; Kang, Sung-Bum; Kim, Woo Ho; Lee, Hye Seung

2016-01-01

Background The immunoscore (IS), an index based on the density of CD3+ and CD8+ tumor-infiltrating lymphocytes (TILs) in the tumor center (CT) and invasive margin (IM), has gained considerable attention as a prognostic marker. Tumor-associated macrophages (TAMs) have also been reported to have prognostic value. However, its clinical significance has not been fully clarified in patients with advanced CRC who present with distant metastases. Methods The density of CD3+, CD4+, CD8+, FOXP3+, CD68+, and CD163+ immune cells within CRC tissue procured from three sites–the primary CT, IM, and distant metastasis (DM)–was determined using immunohistochemistry and digital image analyzer (n=196). The IS was obtained by quantifying the densities of CD3+ and CD8+ TILs in the CT and IM. IS-metastatic and IS-macrophage–additional IS models designed in this study–were obtained by adding the score of CD3 and CD8 in DM and the score of CD163 in primary tumors (CT and IM), respectively, to the IS. Result Higher IS, IS-metastatic, and IS-macrophage values were significantly correlated with better prognosis (p=0.020, p≤0.001, and p=0.005, respectively). Multivariate analysis revealed that only IS-metastatic was an independent prognostic marker (p=0.012). No significant correlation was observed between KRAS mutation and three IS models. However, in the subgroup analysis, IS-metastatic showed a prognostic association regardless of the KRAS mutational status. Conclusion IS is a reproducible method for predicting the survival of patients with advanced CRC. Additionally, an IS including the CD3+ and CD8+ TIL densities at DM could be a strong prognostic marker for advanced CRC. PMID:27835889

Laminar and regional distribution of galanin binding sites in cat and monkey visual cortex determined by in vitro receptor autoradiography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosier, A.M.; Vandesande, F.; Orban, G.A.

1991-03-08

The distribution of galanin (GAL) binding sites in the visual cortex of cat and monkey was determined by autoradiographic visualization of ({sup 125}I)-GAL binding to tissue sections. Binding conditions were optimized and, as a result, the binding was saturable and specific. In cat visual cortex, GAL binding sites were concentrated in layers I, IVc, V, and VI. Areas 17, 18, and 19 exhibited a similar distribution pattern. In monkey primary visual cortex, the highest density of GAL binding sites was observed in layers II/III, lower IVc, and upper V. Layers IVA and VI contained moderate numbers of GAL binding sites,more » while layer I and the remaining parts of layer IV displayed the lowest density. In monkey secondary visual cortex, GAL binding sites were mainly concentrated in layers V-VI. Layer IV exhibited a moderate density, while the supragranular layers contained the lowest proportion of GAL binding sites. In both cat and monkey, we found little difference between regions subserving central and those subserving peripheral vision. Similarities in the distribution of GAL and acetylcholine binding sites are discussed.« less

Bombing Target Identification from Limited Transect Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, Barry L.; Hathaway, John E.; Pulsipher, Brent A.

2006-08-07

A series of sensor data combined with geostatistical techniques were used to determine likely target areas for a historic military aerial bombing range. Primary data consisted of magnetic anomaly information from limited magnetometer transects across the site. Secondary data included airborne LIDAR, orthophotography, and other general site characterization information. Identification of likely target areas relied primarily upon kriging estimates of magnetic anomaly densities across the site. Secondary information, such as impact crater locations, was used to refine the boundary delineations.

Influence of abiotic and environmental factors on the density and infection prevalence of Ixodes pacificus (Acari:Ixodidae) with Borrelia burgdorferi.

PubMed

Swei, A; Meentemeyer, R; Briggs, C J

2011-01-01

The abiotic and biotic factors that govern the spatial distribution of Lyme disease vectors are poorly understood. This study addressed the influence of abiotic and biotic environmental variables on Ixodes pacificus Cooley & Kohls (Acari:Ixodidae) nymphs, because it is the primary vector of Borrelia burgdorferi Johnson, Schmidt, Hyde, Steigerwaldt & Brenner in the far-western United States. Three metrics of Lyme disease risk were evaluated: the density of nymphs, the density of infected nymphs, and the nymphal infection prevalence. This study sampled randomly located plots in oak (Quercus spp.) woodland habitat in Sonoma County, CA. Each plot was drag-sampled for nymphal ticks and tested for B. burgdorferi infection. Path analysis was used to evaluate the direct and indirect relationship between topographic, forest structure and microclimatic variables on ticks. Significant negative correlations were found between maximum temperature in the dry season and the density of infected ticks in 2006 and tick density in 2007, but we did not find a significant relationship with nymphal infection prevalence in either year. Tick density and infected tick density had an indirect, positive correlation with elevation, mediated through temperature. This study found that in certain years but not others, temperature maxima in the dry season may constrain the density and density of infected I. pacificus nymphs. In other years, biotic or stochastic factors may play a more important role in determining tick density.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Shu-Xia; Zhang, Yu-Ru; Research Group PLASMANT, Department of Chemistry, University of Antwerp, Universiteitsplein 1, B-2610 Antwerp

A hybrid model is used to investigate the fragmentation of C{sub 4}F{sub 8} inductive discharges. Indeed, the resulting reactive species are crucial for the optimization of the Si-based etching process, since they determine the mechanisms of fluorination, polymerization, and sputtering. In this paper, we present the dissociation degree, the density ratio of F vs. C{sub x}F{sub y} (i.e., fluorocarbon (fc) neutrals), the neutral vs. positive ion density ratio, details on the neutral and ion components, and fractions of various fc neutrals (or ions) in the total fc neutral (or ion) density in a C{sub 4}F{sub 8} inductively coupled plasma source,more » as well as the effect of pressure and power on these results. To analyze the fragmentation behavior, the electron density and temperature and electron energy probability function (EEPF) are investigated. Moreover, the main electron-impact generation sources for all considered neutrals and ions are determined from the complicated C{sub 4}F{sub 8} reaction set used in the model. The C{sub 4}F{sub 8} plasma fragmentation is explained, taking into account many factors, such as the EEPF characteristics, the dominance of primary and secondary processes, and the thresholds of dissociation and ionization. The simulation results are compared with experiments from literature, and reasonable agreement is obtained. Some discrepancies are observed, which can probably be attributed to the simplified polymer surface kinetics assumed in the model.« less

Bulk plasma fragmentation in a C4F8 inductively coupled plasma: A hybrid modeling study

NASA Astrophysics Data System (ADS)

Zhao, Shu-Xia; Zhang, Yu-Ru; Gao, Fei; Wang, You-Nian; Bogaerts, Annemie

2015-06-01

A hybrid model is used to investigate the fragmentation of C4F8 inductive discharges. Indeed, the resulting reactive species are crucial for the optimization of the Si-based etching process, since they determine the mechanisms of fluorination, polymerization, and sputtering. In this paper, we present the dissociation degree, the density ratio of F vs. CxFy (i.e., fluorocarbon (fc) neutrals), the neutral vs. positive ion density ratio, details on the neutral and ion components, and fractions of various fc neutrals (or ions) in the total fc neutral (or ion) density in a C4F8 inductively coupled plasma source, as well as the effect of pressure and power on these results. To analyze the fragmentation behavior, the electron density and temperature and electron energy probability function (EEPF) are investigated. Moreover, the main electron-impact generation sources for all considered neutrals and ions are determined from the complicated C4F8 reaction set used in the model. The C4F8 plasma fragmentation is explained, taking into account many factors, such as the EEPF characteristics, the dominance of primary and secondary processes, and the thresholds of dissociation and ionization. The simulation results are compared with experiments from literature, and reasonable agreement is obtained. Some discrepancies are observed, which can probably be attributed to the simplified polymer surface kinetics assumed in the model.

Optimization of human corneal endothelial cell culture: density dependency of successful cultures in vitro.

PubMed

Peh, Gary S L; Toh, Kah-Peng; Ang, Heng-Pei; Seah, Xin-Yi; George, Benjamin L; Mehta, Jodhbir S

2013-05-03

Global shortage of donor corneas greatly restricts the numbers of corneal transplantations performed yearly. Limited ex vivo expansion of primary human corneal endothelial cells is possible, and a considerable clinical interest exists for development of tissue-engineered constructs using cultivated corneal endothelial cells. The objective of this study was to investigate the density-dependent growth of human corneal endothelial cells isolated from paired donor corneas and to elucidate an optimal seeding density for their extended expansion in vitro whilst maintaining their unique cellular morphology. Established primary human corneal endothelial cells were propagated to the second passage (P2) before they were utilized for this study. Confluent P2 cells were dissociated and seeded at four seeding densities: 2,500 cells per cm2 ('LOW'); 5,000 cells per cm2 ('MID'); 10,000 cells per cm2 ('HIGH'); and 20,000 cells per cm2 ('HIGH(×2)'), and subsequently analyzed for their propensity to proliferate. They were also subjected to morphometric analyses comparing cell sizes, coefficient of variance, as well as cell circularity when each culture became confluent. At the two lower densities, proliferation rates were higher than cells seeded at higher densities, though not statistically significant. However, corneal endothelial cells seeded at lower densities were significantly larger in size, heterogeneous in shape and less circular (fibroblastic-like), and remained hypertrophic after one month in culture. Comparatively, cells seeded at higher densities were significantly homogeneous, compact and circular at confluence. Potentially, at an optimal seeding density of 10,000 cells per cm2, it is possible to obtain between 10 million to 25 million cells at the third passage. More importantly, these expanded human corneal endothelial cells retained their unique cellular morphology. Our results demonstrated a density dependency in the culture of primary human corneal endothelial cells. Sub-optimal seeding density results in a decrease in cell saturation density, as well as a loss in their proliferative potential. As such, we propose a seeding density of not less than 10,000 cells per cm2 for regular passage of primary human corneal endothelial cells.

Immune cell profile of sentinel lymph nodes in patients with malignant melanoma – FOXP3+ cell density in cases with positive sentinel node status is associated with unfavorable clinical outcome

PubMed Central

2013-01-01

Background Besides being a preferential site of early metastasis, the sentinel lymph node (SLN) is also a privileged site of T-cell priming, and may thus be an appropriate target for investigating cell types involved in antitumor immune reactions. Methods In this retrospective study we determined the prevalence of OX40+ activated T lymphocytes, FOXP3+ (forkhead box P3) regulatory T cells, DC-LAMP+ (dendritic cell-lysosomal associated membrane protein) mature dendritic cells (DCs) and CD123+ plasmacytoid DCs by immunohistochemistry in 100 SLNs from 60 melanoma patients. Density values of each cell type in SLNs were compared to those in non-sentinel nodes obtained from block dissections (n = 37), and analyzed with regard to associations with clinicopathological parameters and disease outcome. Results Sentinel nodes showed elevated amount of all cell types studied in comparison to non-sentinel nodes. Metastatic SLNs had higher density of OX40+ lymphocytes compared to tumor-negative nodes, while no significant difference was observed in the case of the other cell types studied. In patients with positive sentinel node status, high amount of FOXP3+ cells in SLNs was associated with shorter progression-free (P = 0.0011) and overall survival (P = 0.0014), while no significant correlation was found in the case of sentinel-negative patients. The density of OX40+, CD123+ or DC-LAMP+ cells did not show significant association with the outcome of the disease. Conclusions Taken together, our results are compatible with the hypothesis of functional competence of sentinel lymph nodes based on the prevalence of the studied immune cells. The density of FOXP3+ lymphocytes showed association with progression and survival in patients with positive SLN status, while the other immune markers studied did not prove of prognostic importance. These results, together with our previous findings on the prognostic value of activated T cells and mature DCs infiltrating primary melanomas, suggest that immune activation-associated markers in the primary tumor may have a higher impact than those in SLNs on the prognosis of the patients. On the other hand, FOXP3+ cell density in SLNs, but not in the primary tumor, was found predictive of disease outcome in melanoma patients. PMID:23418928

Experimentally Determined Plasma Parameters in a 30 cm Ion Engine

NASA Technical Reports Server (NTRS)

Sengupta, Anita; Goebel, Dan; Fitzgerald, Dennis; Owens, Al; Tynan, George; Dorner, Russ

2004-01-01

Single planar Langmuir probes and fiber optic probes are used to concurrently measure the plasma properties and neutral density variation in a 30cm diameter ion engine discharge chamber, from the immediate vicinity of the keeper to the near grid plasma region. The fiber optic probe consists of a collimated optical fiber recessed into a double bore ceramic tube fitted with a stainless steel light-limiting window. The optical fiber probe is used to measure the emission intensity of excited neutral xenon for a small volume of plasma, at various radial and axial locations. The single Langmuir probes, are used to generate current-voltage characteristics at a total of 140 spatial locations inside the discharge chamber. Assuming a maxwellian distribution for the electron population, the Langmuir probe traces provide spatially resolved measurements of plasma potential, electron temperature, and plasma density. Data reduction for the NSTAR TH8 and TH15 throttle points indicates an electron temperature range of 1 to 7.9 eV and an electron density range of 4e10 to le13 cm(sup -3), throughout the discharge chamber, consistent with the results in the literature. Plasma potential estimates, computed from the first derivative of the probe characteristic, indicate potential from 0.5V to 11V above the discharge voltage along the thruster centerline. These values are believed to be excessively high due to the sampling of the primary electron population along the thruster centerline. Relative neutral density profiles are also obtained with a fiber optic probe sampling photon flux from the 823.1 nm excited to ground state transition. Plasma parameter measurements and neutral density profiles will be presented as a function of probe location and engine discharge conditions. A discussion of the measured electron energy distribution function will also be presented, with regards to variation from pure maxwellian. It has been found that there is a distinct primary population found along the thruster centerline, which causes estimates of electron temperature, electron density, and plasma potential, to err on the high side, due this energetic population. Computation of the energy distribution fimction of the plasma clearly indicates the presence of primaries, whose presence become less obvious with radial distance from the main discharge plume.

Fluorinated Carbon Composite Cathode for a High Energy Lithium Battery (Briefing Charts)

DTIC Science & Technology

2011-02-16

REPORT DOCUMENTATION PAGE Standard Form 298 (Rev. 8/98) Prescribed by ANSI Std. Z39.18 Form Approved OMB No. 0704-0188 The public reporting burden...monofluoride (Li/ CFx ) primary batteries have double energy density over state-of-the-art Li/MnO2 and Li/SO2 primary batteries (theoretically 2203 Wh/kg...temperature operating conditions. This invention relates to a high energy density Li/ CFx primary battery technology with substantial reduction in

Lipid Profiles, Inflammatory Markers, and Insulin Therapy in Youth with Type 2 Diabetes.

PubMed

Levitt Katz, Lorraine E; Bacha, Fida; Gidding, Samuel S; Weinstock, Ruth S; El Ghormli, Laure; Libman, Ingrid; Nadeau, Kristen J; Porter, Kristin; Marcovina, Santica

2018-05-01

Data regarding atherogenic dyslipidemia and the inflammation profile in youth with type 2 diabetes is limited and the effect of insulin therapy on these variables has not previously been studied in youth. We determined the impact of insulin therapy on lipid and inflammatory markers in youth with poorly controlled type 2 diabetes. In the Treatment Options for type 2 Diabetes in Adolescents and Youth (TODAY) multicenter trial, 285 participants failed to sustain glycemic control on randomized treatment (primary outcome, glycated hemoglobin A1c [HbA1c] at ≥8% for 6 months); 363 maintained glycemic control (never reached primary outcome). Statins were used for a low-density lipoprotein cholesterol of ≥130 mg/dL. Upon reaching the primary outcome, insulin was started. Changes in lipids and inflammatory markers (slopes over time) were examined. Progression of dyslipidemia was related to glycemic control. In those with the primary outcome, insulin therapy impacted HbA1c modestly, and dampened the increase in total cholesterol, low-density lipoprotein cholesterol, and total apolipoprotein B, although statin use increased from 8.6% to 22% year after the primary outcome. The increase in triglycerides and plasma nonesterified fatty acids stabilized after insulin was started, independent of HbA1c. There was an increase in high-sensitivity C-reactive protein that continued after insulin initiation, related to HbA1c and percent overweight. Worsening dyslipidemia and inflammation over time raise concern regarding premature development of atherosclerosis in youth with type 2 diabetes. Insulin therapy has a limited benefit in the absence of glycemic control. Strategies to achieve better glycemic control are needed. ClinicalTrials.gov: NCT00081328. Copyright © 2017 Elsevier Inc. All rights reserved.

[Structural recovering in Andean successional forests from Porce (Antioquia, Colombia)].

PubMed

Yepes, Adriana P; del Valle, Jorge I; Jaramillo, Sandra L; Orrego, Sergio A

2010-03-01

Places subjected to natural or human disturbance can recover forest through an ecological process called secondary succession. Tropical succession is affected by factors such as disturbances, distance from original forest, surface configuration and local climate. These factors determine the composition of species and the time trend of the succession itself. We studied succession in soils used for cattle ranching over various decades in the Porce Region of Colombia (Andean Colombian forests). A set of twenty five permanent plots was measured, including nine plots (20 x 50 m) in primary forests and sixteen (20 x 25 m) in secondary forests. All trees with diameter > or =1.0 cm were measured. We analyzed stem density, basal area, above-ground biomass and species richness, in a successional process of ca. 43 years, and in primary forests. The secondary forests' age was estimated in previous studies, using radiocarbon dating, aerial photographs and a high-resolution satellite image analysis (7 to >43 years). In total, 1,143 and 1,766 stems were measured in primary and secondary forests, respectively. Basal area (5.7 to 85.4 m2 ha(-1)), above-ground biomass (19.1 to 1,011.5 t ha(-1)) and species richness (4 to 69) directly increased with site age, while steam density decreased (3,180 to 590). Diametric distributions were "J-inverted" for primary forests and even-aged size-class structures for secondary forests. Three species of palms were abundant and exclusive in old secondary forests and primary forests: Oenocarpus mapora, Euterpe precatoria and Oenocarpus bataua. These palms happened in cohorts after forest disturbances. Secondary forest structure was 40% in more than 43 years of forest succession and indicate that many factors are interacting and affecting the forests succession in the area (e.g. agriculture, cattle ranching, mining, etc.).

Much NICER Monitoring of the X-ray Spectrum of Eta Carinae

NASA Astrophysics Data System (ADS)

Corcoran, Michael Francis; Hamaguchi, Kenji; Drake, Stephen; Pasham, Dheeraj; Gendreau, Keith C.; Arzoumanian, Zaven

2018-01-01

Eta Carinae is the most massive and luminous stellar system within 3 kpc. It is a known binary system with an orbital period of 5.52 years in which bright, thermal, X-ray emission is produced by a strong shock driven by the collisions of the wind of the visible primary star with the thin, fast wind of an otherwise unseen companion. Variations of the X-ray spectrum are produced by intrinsic changes in the density of the hot shocked gas and by intervening changes in wind absorption as the two stars revolve in a long-period, highly eccentric orbit. Previous X-ray monitoring studies since 1996 have detailed these variations, but have been either restricted to the E>3 keV band or have been affected by optical loading which limited measurement of X-ray absorption changes which can be used to determine the overlying density profile of the primary's wind around the orbit. The Neutron Star Interior Composition Explorer (NICER) is an excellent general-purpose observatory for X-ray astronomy, and in particular, its soft response and large effective area facilitate monitoring of X-ray spectral variations for bright sources like Eta Car without any bias due to photon pileup. We present the first observations of the X-ray spectrum of Eta Car obtained by NICER, and discuss limits on changes in column density, emission measure and temperature we derive from the NICER spectra.

High nymphal host density and mortality negatively impact parasitoid complex during an insect herbivore outbreak.

PubMed

Hall, Aidan A G; Johnson, Scott N; Cook, James M; Riegler, Markus

2017-08-26

Insect herbivore outbreaks frequently occur and this may be due to factors that restrict top-down control by parasitoids, for example, host-parasitoid asynchrony, hyperparasitization, resource limitation and climate. Few studies have examined host-parasitoid density relationships during an insect herbivore outbreak in a natural ecosystem with diverse parasitoids. We studied parasitization patterns of Cardiaspina psyllids during an outbreak in a Eucalyptus woodland. First, we established the trophic roles of the parasitoids through a species-specific multiplex PCR approach on mummies from which parasitoids emerged. Then, we assessed host-parasitoid density relationships across three spatial scales (leaf, tree and site) over one year. We detected four endoparasitoid species of the family Encyrtidae (Hymenoptera); two primary parasitoid and one heteronomous hyperparasitoid Psyllaephagus species (the latter with female development as a primary parasitoid and male development as a hyperparasitoid), and the hyperparasitoid Coccidoctonus psyllae. Parasitoid development was host-synchronized, although synchrony between sites appeared constrained during winter (due to temperature differences). Parasitization was predominantly driven by one primary parasitoid species and was mostly inversely host-density dependent across the spatial scales. Hyperparasitization by C. psyllae was psyllid-density dependent at the site scale, however, this only impacted the rarer primary parasitoid. High larval parasitoid mortality due to density-dependent nymphal psyllid mortality (a consequence of resource limitation) compounded by a summer heat wave was incorporated in the assessment and resulted in density independence of host-parasitoid relationships. As such, high larval parasitoid mortality during insect herbivore outbreaks may contribute to the absence of host density-dependent parasitization during outbreak events. © 2017 Institute of Zoology, Chinese Academy of Sciences.

The changes of densities and patterns of roads and rural buildings: a case study on Dongzhi Yuan of the Loess Plateau, China.

PubMed

Bi, Xiaoli; Wang, Hui; Ge, Jianping

2010-05-01

Roads and buildings are considered as primary causes of rural landscape changes. In this study, linear regression models were used to analyze the dynamic influences of environmental factors and variables on roads and rural buildings from 1979 to 2005 in Dongzhi Yuan (tableland) of the Loess Plateau, China. The relationship between roads and rural buildings and their effects on Dongzhi Yuan are discussed also. The results showed that three environmental factors (topography, land cover, and development level) explained roads better than rural buildings referring densities and patterns. The environmental variables significantly related to roads have decreased, whereas those related to rural buildings have increased over time. Among these significant variables, percent of farmland mostly determined the densities and patterns of both roads and rural buildings. There was significant correlation between roads and rural buildings in terms of density and pattern. In addition, roads and rural buildings have increased greatly in gully areas of this region. Therefore, more attention should be paid to planning of roads and rural buildings in Dongzhi Yuan.

Ecological Modeling of Aedes aegypti (L.) Pupal Production in Rural Kamphaeng Phet, Thailand

PubMed Central

Aldstadt, Jared; Koenraadt, Constantianus J. M.; Fansiri, Thanyalak; Kijchalao, Udom; Richardson, Jason; Jones, James W.; Scott, Thomas W.

2011-01-01

Background Aedes aegypti (L.) is the primary vector of dengue, the most important arboviral infection globally. Until an effective vaccine is licensed and rigorously administered, Ae. aegypti control remains the principal tool in preventing and curtailing dengue transmission. Accurate predictions of vector populations are required to assess control methods and develop effective population reduction strategies. Ae. aegypti develops primarily in artificial water holding containers. Release recapture studies indicate that most adult Ae. aegypti do not disperse over long distances. We expect, therefore, that containers in an area of high development site density are more likely to be oviposition sites and to be more frequently used as oviposition sites than containers that are relatively isolated from other development sites. After accounting for individual container characteristics, containers more frequently used as oviposition sites are likely to produce adult mosquitoes consistently and at a higher rate. To this point, most studies of Ae. aegypti populations ignore the spatial density of larval development sites. Methodology Pupal surveys were carried out from 2004 to 2007 in rural Kamphaeng Phet, Thailand. In total, 84,840 samples of water holding containers were used to estimate model parameters. Regression modeling was used to assess the effect of larval development site density, access to piped water, and seasonal variation on container productivity. A varying-coefficients model was employed to account for the large differences in productivity between container types. A two-part modeling structure, called a hurdle model, accounts for the large number of zeroes and overdispersion present in pupal population counts. Findings The number of suitable larval development sites and their density in the environment were the primary determinants of the distribution and abundance of Ae. aegypti pupae. The productivity of most container types increased significantly as habitat density increased. An ecological approach, accounting for development site density, is appropriate for predicting Ae. aegypti population levels and developing efficient vector control programs. PMID:21267055

Using Landscape Analysis to Test Hypotheses about Drivers of Tick Abundance and Infection Prevalence with Borrelia burgdorferi.

PubMed

Ferrell, A Michelle; Brinkerhoff, R Jory

2018-04-12

Patterns of vector-borne disease risk are changing globally in space and time and elevated disease risk of vector-borne infection can be driven by anthropogenic modification of the environment. Incidence of Lyme disease, caused by the bacterium Borrelia burgdorferi sensu stricto, has risen in a number of locations in North America and this increase may be driven by spatially or numerically expanding populations of the primary tick vector, Ixodes scapularis . We used a model selection approach to identify habitat fragmentation and land-use/land cover variables to test the hypothesis that the amount and configuration of forest cover at spatial scales relevant to deer, the primary hosts of adult ticks, would be the predominant determinants of tick abundance. We expected that land cover heterogeneity and amount of forest edge, a habitat thought to facilitate deer foraging and survival, would be the strongest driver of tick density and that larger spatial scales (5-10 km) would be more important than smaller scales (1 km). We generated metrics of deciduous and mixed forest fragmentation using Fragstats 4.4 implemented in ArcMap 10.3 and found, after adjusting for multicollinearity, that total forest edge within a 5 km buffer had a significant negative effect on tick density and that the proportion of forested land cover within a 10 km buffer was positively associated with density of I. scapularis nymphs. None of the 1 km fragmentation metrics were found to significantly improve the fit of the model. Elevation, previously associated with increased density of I. scapularis nymphs in Virginia, while significantly predictive in univariate analysis, was not an important driver of nymph density relative to fragmentation metrics. Our results suggest that amount of forest cover (i.e., lack of fragmentation) is the most important driver of I. scapularis density in our study system.

[Density of beta-adrenergic receptors and left ventricular mass in patients with primary essential hypertension].

PubMed

Gajek, J; Zyśko, D; Spring, A

2000-08-01

Left ventricular hypertrophy (LVH) is one of the more important risk factors for sudden death. There are multiple factors for development of LVH in patients with hypertension. Sympathetic nervous system may play a key role causing afterload increase and neurohumoral mechanisms activation. The aim of the study was to determine beta-adrenergic receptors density and its relations to left ventricular mass in hypertensive subjects. The study was carried out in 63 patients (23 women and 40 men), mean age 43.3 +/- 11.6 yrs with primary hypertension: stage I--42 pts and stage II--21 pts. The control group consisted of 26 healthy persons matched for age and sex. We evaluated the density of beta-adrenergic receptors using 125I-cyanopindolol radioligand labeling method. Left ventricular dimensions were assessed by echocardiography (Hewlett-Packard 77010 CF) and left ventricular mass index (LVMI) was calculated. Systolic and diastolic blood pressure and LVMI was significantly higher in hypertension group 156.7 +/- 12.5 vs. 119.8 +/- 8.8 mmHg, p < 0.0001, 95.9/5.5 vs. 78.8 +/- 6.5 mmHg, p < 0.0001, 126.5 +/- 41.9 vs. 93.1 +/- 19.9 g/m2, p < 0.001 respectively. Beta-adrenergic receptors density was 40.7 +/- 29.9 fmol/ml in the hypertensive vs. 37.2 +/- 17.8 fmol/ml in control group (p = NS). There was no correlation between beta-adrenergic receptors density and LVMI. There was a statistically significant positive correlation between LVMI and systolic and diastolic blood pressure (r = 0.44, p < 0.05; r = 0.60, p < 0.01 respectively). 1. Beta-adrenergic receptors density was unchanged in patients with hypertension and did not correlate with LVMI. 2. A high positive correlation between blood pressure values and LVMI, but only in stage II hypertension was revealed.

Primary stability and self-tapping blades: biomechanical assessment of dental implants in medium-density bone.

PubMed

Kim, Yung-Soo; Lim, Young-Jun

2011-10-01

The aim of this biomechanical study was to assess the influence of self-tapping blades in terms of primary implant stability between implants with self-tapping blades and implants without self-tapping blades using five different analytic methods, especially in medium-density bone. Two different types of dental implants (4 × 10 mm) were tested: self-tapping and non-self-tapping. The fixture design including thread profiles was exactly the same between the two groups; the only difference was the presence of cutting blades on one half of the apical portion of the implant body. Solid rigid polyurethane blocks with corresponding densities were selected to simulate medium-density bone. Five mechanical assessments (insertion torque, resonance frequency analysis [RFA], reverse torque, pull-out and push in test) were performed for primary stability. Implants without self-tapping blades showed significantly higher values (P<0.001) in four biomechanical assessments, except RFA (P=0.684). However, a statistically significant correlation could not be detected between insertion torque values with the four different outcome variables (P>0.05). The outcomes of the present study indicate that the implant body design without self-tapping blades has a good primary stability compared with that with self-tapping blades in medium-density bone. Considering the RFA, a distinct layer of cortical bone on marginal bone will yield implant stability quotient values similar to those in medium-bone density when implants have the same diameter. © 2011 John Wiley & Sons A/S.

Investigative Homework with Apples: An Opportunity for Primary-School Students to Learn Actively the Relationship between Density and Flotation

ERIC Educational Resources Information Center

Radovanovic, Jelena; Sliško, Josip

2014-01-01

This paper describes investigative homework with apples, aiming to contribute to the primary-school students' understanding of density and conditions leading to floating and sinking. The assignment represents an opportunity for individual autonomous learning of physics and adoption of established scientific concepts through practical activities…

Return currents in solar flares - Collisionless effects

NASA Technical Reports Server (NTRS)

Rowland, H. L.; Vlahos, L.

1985-01-01

If the primary, precipitating electrons in a solar flare are unstable to beam plasma interactions, it is shown that strong Langmuir turbulence can seriously modify the way in which a return current is carried by the background plasma. In particular, the return (or reverse) current will not be carried by the bulk of the electrons, but by a small number of high velocity electrons. For beam/plasma densities greater than 0.01, this can reduce the effects of collisions on the return current. For higher density beams where the return current could be unstable to current driven instabilities, the effects of strong turbulence anomalous resistivity is shown to prevent the appearance of such instabilities. Again in this regime, how the return current is carried is determined by the beam generated strong turbulence.

Advances in compact proton spectrometers for inertial-confinement fusion and plasma nuclear science.

PubMed

Seguin, F H; Sinenian, N; Rosenberg, M; Zylstra, A; Manuel, M J-E; Sio, H; Waugh, C; Rinderknecht, H G; Johnson, M Gatu; Frenje, J; Li, C K; Petrasso, R; Sangster, T C; Roberts, S

2012-10-01

Compact wedge-range-filter proton spectrometers cover proton energies ∼3-20 MeV. They have been used at the OMEGA laser facility for more than a decade for measuring spectra of primary D(3)He protons in D(3)He implosions, secondary D(3)He protons in DD implosions, and ablator protons in DT implosions; they are now being used also at the National Ignition Facility. The spectra are used to determine proton yields, shell areal density at shock-bang time and compression-bang time, fuel areal density, and implosion symmetry. There have been changes in fabrication and in analysis algorithms, resulting in a wider energy range, better accuracy and precision, and better robustness for survivability with indirect-drive inertial-confinement-fusion experiments.

Plasticity in skeletal characteristics of nursery-raised staghorn coral, Acropora cervicornis

USGS Publications Warehouse

Kuffner, Ilsa B.; Bartels, Erich; Stathakopoulos, Anastasios; Enochs, Ian C.; Kolodziej, Graham; Toth, Lauren; Manzello, Derek P.

2017-01-01

Staghorn coral, Acropora cervicornis, is a threatened species and the primary focus of western Atlantic reef restoration efforts to date. We compared linear extension, calcification rate, and skeletal density of nursery-raised A. cervicornis branches reared for 6 months either on blocks attached to substratum or hanging from PVC trees in the water column. We demonstrate that branches grown on the substratum had significantly higher skeletal density, measured using computerized tomography, and lower linear extension rates compared to water-column fragments. Calcification rates determined with buoyant weighing were not statistically different between the two grow-out methods, but did vary among coral genotypes. Whereas skeletal density and extension rates were plastic traits that depended on grow-out method, calcification rate was conserved. Our results show that the two rearing methods generate the same amount of calcium carbonate skeleton but produce colonies with different skeletal characteristics and suggest that there is genetically based variability in coral calcification performance.

Prevalence of unrecognized dyslipidaemia in Dubai and Northern Emirates: a cross-sectional hospital based study.

PubMed

Vela, Barbara Karin; Alhessi, Alaaeldin Y; Popović, Marko; Al-Shaqra, Maryam A

2008-12-01

The aim of this study is to determine the prevalence of unrecognized dyslipidaemia and a specific correlation between lipid values and age, gender or ethnic origin in the study population. This retrospective cross-sectional study included 311 subjects who had their lipid profiles checked for the first time in a private hospital in Dubai in a six month - period. The analysis shows an increased prevalence of Low Density Lipoprotein (LDL) hypercholesterolemia with relatively higher Low Density Lipoprotein Cholesterol (LDL-c) values in male subjects (p < 0.016) as well as with the Middle East ethnic origin group (p < 0.025), while desirable High Density Lipoprotein (HDL-c) was found among female subjects (p = 0). The discordance between the percentages of elevated LDL-c and Total cholesterol (T-c) signifies the role of the LDL-c/non-HDL-c as the main surrogate for dyslipidaemia as a risk for atherosclerosis, and as a primary target of therapy.

Plasticity in skeletal characteristics of nursery-raised staghorn coral, Acropora cervicornis

NASA Astrophysics Data System (ADS)

Kuffner, Ilsa B.; Bartels, Erich; Stathakopoulos, Anastasios; Enochs, Ian C.; Kolodziej, G.; Toth, Lauren T.; Manzello, Derek P.

2017-09-01

Staghorn coral, Acropora cervicornis, is a threatened species and the primary focus of western Atlantic reef restoration efforts to date. We compared linear extension, calcification rate, and skeletal density of nursery-raised A. cervicornis branches reared for 6 months either on blocks attached to substratum or hanging from PVC trees in the water column. We demonstrate that branches grown on the substratum had significantly higher skeletal density, measured using computerized tomography, and lower linear extension rates compared to water-column fragments. Calcification rates determined with buoyant weighing were not statistically different between the two grow-out methods, but did vary among coral genotypes. Whereas skeletal density and extension rates were plastic traits that depended on grow-out method, calcification rate was conserved. Our results show that the two rearing methods generate the same amount of calcium carbonate skeleton but produce colonies with different skeletal characteristics and suggest that there is genetically based variability in coral calcification performance.

Primary Energy Reconstruction from the Charged Particle Densities Recorded with the KASCADE-Grande Detector at 500 m Distance from Shower Core

NASA Astrophysics Data System (ADS)

Toma, G.; Apel, W. D.; Arteaga, J. C.; Bekk, K.; Bertaina, M.; Blümer, J.; Bozdog, H.; Brancus, I. M.; Buchholz, P.; Cantoni, E.; Chiavassa, A.; Cossavella, F.; Daumiller, K.; de Souza, V.; di Pierro, F.; Doll, P.; Engel, R.; Engler, J.; Finger, M.; Fuhrmann, D.; Ghia, P. L.; Gils, H. J.; Glasstetter, R.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Huege, T.; Isar, P. G.; Kampert, K.-H.; Kang, D.; Kickelbick, D.; Klages, H. O.; Link, K.; Łuczak, P.; Ludwig, M.; Mathes, H. J.; Mayer, H. J.; Melissas, M.; Milke, J.; Mitrica, B.; Morello, C.; Navarra, G.; Nehls, S.; Oehlschläger, J.; Ostapchenko, S.; Over, S.; Palmieri, N.; Petcu, M.; Pierog, T.; Rebel, H.; Roth, M.; Schieler, H.; Schröder, F.; Sima, O.; Trinchero, G. C.; Ulrich, H.; Weindl, A.; Wochele, J.; Wommer, M.; Zabierowski, J.

2010-11-01

Previous EAS investigations have shown that for a fixed primary energy the charged particle density becomes independent of the primary mass at certain (fixed) distances from the shower core. This feature can be used as an estimator for the primary energy. We present results on the reconstruction of the primary energy spectrum of cosmic rays from the experimentally recorded S(500) observable (the density of charged particles at 500 m distance to the shower core) using the KASCADE-Grande detector array. The KASCADE-Grande experiment is hosted by the Karlsruhe Institute for Technology-Campus North, Karlsruhe, Germany, and operated by an international collaboration. The constant intensity cut (CIC) method is applied to evaluate the attenuation of the S(500) observable with the zenith angle and is corrected for. A calibration of S(500) values with the primary energy has been worked out by simulations and was applied to the data to obtain the primary energy spectrum (in the energy range log10[E0/GeV]∈[7.5,9]). The systematic uncertainties induced by different sources are considered. In addition, a correction based on a response matrix is applied to account for the effects of shower-to-shower fluctuations on the spectral index of the reconstructed energy spectrum.

A laboratory verification sensor

NASA Technical Reports Server (NTRS)

Vaughan, Arthur H.

1988-01-01

The use of a variant of the Hartmann test is described to sense the coalignment of the 36 primary mirror segments of the Keck 10-meter Telescope. The Shack-Hartmann alignment camera is a surface-tilt-error-sensing device, operable with high sensitivity over a wide range of tilt errors. An interferometer, on the other hand, is a surface-height-error-sensing device. In general, if the surface height error exceeds a few wavelengths of the incident illumination, an interferogram is difficult to interpret and loses utility. The Shack-Hartmann aligment camera is, therefore, likely to be attractive as a development tool for segmented mirror telescopes, particularly at early stages of development in which the surface quality of developmental segments may be too poor to justify interferometric testing. The constraints are examined which would define the first-order properties of a Shack-Hartmann alignment camera and the precision and range of measurement one could expect to achieve with it are investigated. Fundamental constraints do arise, however, from consideration of geometrical imaging, diffraction, and the density of sampling of images at the detector array. Geometrical imagining determines the linear size of the image, and depends on the primary mirror diameter and the f-number of a lenslet. Diffraction is another constraint; it depends on the lenslet aperture. Finally, the sampling density at the detector array is important since the number of pixels in the image determines how accurately the centroid of the image can be measured. When these factors are considered under realistic assumptions it is apparent that the first order design of a Shack-Hartmann alignment camera is completely determined by the first-order constraints considered, and that in the case of a 20-meter telescope with seeing-limited imaging, such a camera, used with a suitable detector array, will achieve useful precision.

[Travel times of patients to ambulatory care physicians in Germany].

PubMed

Schang, Laura; Kopetsch, Thomas; Sundmacher, Leonie

2017-12-01

The time needed by patients to get to a doctor's office represents an important indicator of realised access to care. In Germany, findings on travel times are only available from surveys or for some regions. For the first time, this study examines nationwide and physician group-specific travel times in the ambulatory care sector in Germany and describes demographic, supply-side and spatial determinants of variations. Using a full review of patient consultations in the statutory health insurance system from 2009/2010 for 14 physician groups (approximately 518 million cases), case-related travel times by car between patients' places of residence and physician's practices were estimated at the municipal level. Physicians were reached in less than 30 min in 90.8% of cases for primary care physicians and up to 63% of cases for radiologists. Patients between 18 and under 30 years of age travel longer to get to the doctor than other age groups. The average travel time at the county level systematically differs between urban and rural planning areas. In the case of gynecologists, dermatologists and ophthalmologists, the average journey time decreases with increasing physician density at the county level, but remains approximately constant from a recognisable point of inflection. There is no association between primary care physician density and travel time at the district level. Spatial analyses show physician group-specific patterns of regional concentrations with an increased proportion of cases with very long travel times. Patients' travel times are influenced by supply- and demand-side determinants. Interactions between influential determinants should be analysed in depth to examine the extent to which the time travelled is an expression of regional under- or over-supply rather than an expression of patient preferences.

Density tomography using cosmic ray muons: feasibility domain and field applications

NASA Astrophysics Data System (ADS)

Lesparre, N.; Gibert, D.; Marteau, J.; Déclais, Y.; Carbone, D.; Galichet, E.

2010-12-01

Muons are continuously produced when the protons forming the primary cosmic rays decay during their interactions with the molecules of the upper atmosphere. Both their short cross-section and their long life-time make the muons able to cross hectometers and even kilometers of rock before disintegrating. The flux of muons crossing a geological volume strongly depends on the quantity of matter encountered along their trajectories and, depending on both its size and its density, the geological object appears more or less opaque to muons. By measuring the muon flux emerging from the studied object and correcting for its geometry, the density structure can be deduced. The primary information obtained is the density averaged along muons trajectories and, to recover the 3D density distribution. The detector has to be moved around the target to acquire multi-angle images of the density structure. The inverse problem to be solved shares common features with seismic travel-time tomography and X-ray medical scans, but it also has specificities like Poissonian statistics, low signal-to-noise ratio and scattering which are discussed. Muon telescopes have been designed to sustain installations in harsh conditions such as might be encountered on volcanoes. Data acquired in open sky at various latitude and altitude allow to adjust the incoming muon flux model and to observe its temporal variations. The muon interactions with matter and the underground flux are constrained with data sets acquired inside the underground laboratory of the Mont Terri. The data analysis and the telescope model development are detailed. A model of the muon flux across a volcano is confronted to first measurements on La Soufrière de Guadeloupe volcano. The model takes into account a priori informations and solving kernels are computed to deduce the spatial resolution in order to define the elements size of the model heterogeneities. The spatio-temporal resolution of the method is in relation with the geometry and the installation time of the detector, it is evaluated to get the detectable density variations. The impact of additional telescopes around the volcano on the data quality is estimated to determine the best future locations of installations.

Influence of clinostat rotation on fertilized amphibian egg pattern specification

NASA Technical Reports Server (NTRS)

Neff, A. W.; Smith, R. C.; Malacinski, G. M.; Chung, H.-M.

1984-01-01

Pattern specification in fertile Xenopus eggs rotated on horizontal clinostats was monitored with respect to primary embryonic axis formation, subsequent morphogenesis, and compartmentalization of the cytoplasm. At the speeds of 1 to 24 rpm (which are believed to simulate microgravity) a large percentage of eggs developed normal axial structures. Eggs clinostated at 12 rpm showed a randomization of dorsal/ventral polarity. The cytoplasmic compartments showed some clinostat effects but no abnormal mixing, disruption or dislocation of compartments. It is predicted that Xenopus eggs fertilized and allowed to develop in space will retain normal cytoplasmic density compartments, establish primary axes and undergo normal morphogenesis in space. Their dorsal/ventral polarity may not, however, be determined by the sperm entrance site (as is the case for 1 g eggs).

Ionospheric Tomography Using Faraday Rotation of Automatic Dependant Surveillance Broadcast UHF Signals

NASA Astrophysics Data System (ADS)

Cushley, A. C.

2013-12-01

The proposed launch of a satellite carrying the first space-borne ADS-B receiver by the Royal Military College of Canada (RMCC) will create a unique opportunity to study the modification of the 1090 MHz radio waves following propagation through the ionosphere from the transmitting aircraft to the passive satellite receiver(s). Experimental work successfully demonstrated that ADS-B data can be used to reconstruct two dimensional (2D) electron density maps of the ionosphere using computerized tomography (CT). The goal of this work is to evaluate the feasibility of CT reconstruction. The data is modelled using Ray-tracing techniques. This allows us to determine the characteristics of individual waves, including the wave path and the state of polarization at the satellite receiver. The modelled Faraday rotation (FR) is determined and converted to total electron content (TEC) along the ray-paths. The resulting TEC is used as input for computerized ionospheric tomography (CIT) using algebraic reconstruction technique (ART). This study concentrated on meso-scale structures 100-1000 km in horizontal extent. The primary scientific interest of this thesis was to show the feasibility of a new method to image the ionosphere and obtain a better understanding of magneto-ionic wave propagation. Multiple feature input electron density profile to ray-tracing program. Top: reconstructed relative electron density map of ray-trace input (Fig. 1) using TEC measurements and line-of-sight path. Bottom: reconstructed electron density map of ray-trace input using quiet background a priori estimate.

Parasite transmission in social interacting hosts: Monogenean epidemics in guppies

USGS Publications Warehouse

Johnson, M.B.; Lafferty, K.D.; van, Oosterhout C.; Cable, J.

2011-01-01

Background: Infection incidence increases with the average number of contacts between susceptible and infected individuals. Contact rates are normally assumed to increase linearly with host density. However, social species seek out each other at low density and saturate their contact rates at high densities. Although predicting epidemic behaviour requires knowing how contact rates scale with host density, few empirical studies have investigated the effect of host density. Also, most theory assumes each host has an equal probability of transmitting parasites, even though individual parasite load and infection duration can vary. To our knowledge, the relative importance of characteristics of the primary infected host vs. the susceptible population has never been tested experimentally. Methodology/Principal Findings: Here, we examine epidemics using a common ectoparasite, Gyrodactylus turnbulli infecting its guppy host (Poecilia reticulata). Hosts were maintained at different densities (3, 6, 12 and 24 fish in 40 L aquaria), and we monitored gyrodactylids both at a population and individual host level. Although parasite population size increased with host density, the probability of an epidemic did not. Epidemics were more likely when the primary infected fish had a high mean intensity and duration of infection. Epidemics only occurred if the primary infected host experienced more than 23 worm days. Female guppies contracted infections sooner than males, probably because females have a higher propensity for shoaling. Conclusions/Significance: These findings suggest that in social hosts like guppies, the frequency of social contact largely governs disease epidemics independent of host density. ?? 2011 Johnson et al.

Parasite transmission in social interacting hosts: Monogenean epidemics in guppies

USGS Publications Warehouse

Johnson, Mirelle B.; Lafferty, Kevin D.; van Oosterhout, Cock; Cable, Joanne

2011-01-01

Background Infection incidence increases with the average number of contacts between susceptible and infected individuals. Contact rates are normally assumed to increase linearly with host density. However, social species seek out each other at low density and saturate their contact rates at high densities. Although predicting epidemic behaviour requires knowing how contact rates scale with host density, few empirical studies have investigated the effect of host density. Also, most theory assumes each host has an equal probability of transmitting parasites, even though individual parasite load and infection duration can vary. To our knowledge, the relative importance of characteristics of the primary infected host vs. the susceptible population has never been tested experimentally. Methodology/Principal Findings Here, we examine epidemics using a common ectoparasite, Gyrodactylus turnbulli infecting its guppy host (Poecilia reticulata). Hosts were maintained at different densities (3, 6, 12 and 24 fish in 40 L aquaria), and we monitored gyrodactylids both at a population and individual host level. Although parasite population size increased with host density, the probability of an epidemic did not. Epidemics were more likely when the primary infected fish had a high mean intensity and duration of infection. Epidemics only occurred if the primary infected host experienced more than 23 worm days. Female guppies contracted infections sooner than males, probably because females have a higher propensity for shoaling. Conclusions/Significance These findings suggest that in social hosts like guppies, the frequency of social contact largely governs disease epidemics independent of host density.

Critic: a new program for the topological analysis of solid-state electron densities

NASA Astrophysics Data System (ADS)

Otero-de-la-Roza, A.; Blanco, M. A.; Pendás, A. Martín; Luaña, Víctor

2009-01-01

In this paper we introduce CRITIC, a new program for the topological analysis of the electron densities of crystalline solids. Two different versions of the code are provided, one adapted to the LAPW (Linear Augmented Plane Wave) density calculated by the WIEN2K package and the other to the ab initio Perturbed Ion ( aiPI) density calculated with the PI7 code. Using the converged ground state densities, CRITIC can locate their critical points, determine atomic basins and integrate properties within them, and generate several graphical representations which include topological atomic basins and primary bundles, contour maps of ρ and ∇ρ, vector maps of ∇ρ, chemical graphs, etc. Program summaryProgram title: CRITIC Catalogue identifier: AECB_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AECB_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: GPL, version 3 No. of lines in distributed program, including test data, etc.: 1 206 843 No. of bytes in distributed program, including test data, etc.: 12 648 065 Distribution format: tar.gz Programming language: FORTRAN 77 and 90 Computer: Any computer capable of compiling Fortran Operating system: Unix, GNU/Linux Classification: 7.3 Nature of problem: Topological analysis of the electron density in periodic solids. Solution method: The automatic localization of the electron density critical points is based on a recursive partitioning of the Wigner-Seitz cell into tetrahedra followed by a Newton search from significant points on each tetrahedra. Plotting of and integration on the atomic basins is currently based on a new implementation of Keith's promega algorithm. Running time: Variable, depending on the task. From seconds to a few minutes for the localization of critical points. Hours to days for the determination of the atomic basins shape and properties. Times correspond to a typical 2007 PC.

Self-cutting blades and their influence on primary stability of tapered dental implants in a simulated low-density bone model: a laboratory study.

PubMed

Kim, Duck-Rae; Lim, Young-Jun; Kim, Myung-Joo; Kwon, Ho-Beom; Kim, Sung-Hun

2011-11-01

This study tested the hypothesis that there would be differences in primary stability due to the presence of self cutting blades. We investigated the effect of a self-cutting blade implant design on the primary stability of tapered dental implants in a simulated low-density bone model. Implant fixtures with 2 different designs, one with self-cutting blades and the other without self-cutting blades, were fabricated in the same implant system. Insertion torque, resonance frequency analysis, reverse torque, and pull-out and push-in tests were evaluated in grade no. 10 solid rigid polyurethane foam. All 5 assessments of the group without self-cutting blades were significantly higher than those of the self-cutting group (P < .001). The implants without self-cutting blades create a lateral compression with increased contact surface area and consequently improve the primary stability in a simulated low-density bone model. Copyright © 2011 Mosby, Inc. All rights reserved.

Primary propulsion/large space system interaction study

NASA Technical Reports Server (NTRS)

Coyner, J. V.; Dergance, R. H.; Robertson, R. I.; Wiggins, J. V.

1981-01-01

An interaction study was conducted between propulsion systems and large space structures to determine the effect of low thrust primary propulsion system characteristics on the mass, area, and orbit transfer characteristics of large space systems (LSS). The LSS which were considered would be deployed from the space shuttle orbiter bay in low Earth orbit, then transferred to geosynchronous equatorial orbit by their own propulsion systems. The types of structures studied were the expandable box truss, hoop and column, and wrap radial rib each with various surface mesh densities. The impact of the acceleration forces on system sizing was determined and the effects of single point, multipoint, and transient thrust applications were examined. Orbit transfer strategies were analyzed to determine the required velocity increment, burn time, trip time, and payload capability over a range of final acceleration levels. Variables considered were number of perigee burns, delivered specific impulse, and constant thrust and constant acceleration modes of propulsion. Propulsion stages were sized for four propellant combinations; oxygen/hydrogen, oxygen/methane, oxygen/kerosene, and nitrogen tetroxide/monomethylhydrazine, for pump fed and pressure fed engine systems. Two types of tankage configurations were evaluated, minimum length to maximize available payload volume and maximum performance to maximize available payload mass.

Densities of Barrow's goldeneyes during winter in Prince William Sound, Alaska in relation to habitat, food, and history of oil contamination

USGS Publications Warehouse

Esler, Daniel N.; Bowman, Timothy D.; O'Clair, Charles E.; Dean, Thomas A.; McDonald, Lyman L.

2000-01-01

We evaluated variation in densities of Barrow's Goldeneyes (Bucephala islandica) during winter at 214 sites within oiled and unoiled study areas in Prince William Sound, Alaska in relation to physical habitat attributes, prey biomass, and history of habitat contamination by the 1989 Exxon Valdez oil spill. Using general linear model analyses, we found that goldeneye densities were positively associated with occurrence of a stream within 200 m, lack of exposure to wind and waves, and mixed (versus rocky) substrate. We speculate that these associations relate to habitat profitability via selection of beneficial attributes and avoidance of detrimental features. We also determined that biomass of blue mussels (Mytilus trossulus), the primary prey, was not related to Barrow's Goldeneye densities; we suggest that mussel standing stock exceeds predation demands in our study areas and, thus, does not dictate goldeneye distribution. After accounting for habitat effects, we detected no effect of history of oil contamination on Barrow's Goldeneye densities, suggesting that populations have recovered from the oil spill. Although other studies documented hydrocarbon exposure in Barrow's Goldeneyes through at least 1997, either the level of exposure did not affect populations via reductions in survival, or effects of oil exposure were offset by immigration.

Salivary density of Streptococcus mutans and Streptococcus sobrinus and dental caries in children and adolescents with Down syndrome.

PubMed

Scalioni, Flávia; Carrada, Camila; Machado, Fernanda; Devito, Karina; Ribeiro, Luiz Cláudio; Cesar, Dionéia; Ribeiro, Rosangela

2017-01-01

To assess and compare dental caries experience and salivary S. mutans, S. sobrinus, and streptococci counts between groups of Down syndrome and non-Down syndrome children and adolescents. This study included a sample of 30 Down syndrome children and adolescents (G-DS) and 30 age- and sex-matched non-Down syndrome subjects (G-ND). Dental caries experience was estimated by the number of decayed, missing, and filled teeth in the primary dentition and the permanent dentition. Unstimulated whole saliva samples were collected from all participants. The fluorescence in situ hybridization technique was used to identify the presence and counts of the bacteria. The statistical analysis included chi-square, Student's t-test and Spearman's correlation. The G-DS exhibited a significantly higher caries-free rate (p<0.001) and a lower S. mutans salivary density (p<0.001). No significant differences were found in the salivary densities of S. sobrinus or streptococci between the groups (p=0.09 and p=0.21, respectively). The salivary S. mutans or S. sobrinus densities were not associated with dental caries experience in neither group. The reduced dental caries experience observed in this group of Down syndrome children and adolescents cannot be attributed to lower salivary S. mutans densities, as determined with the fluorescence in situ hybridization technique.

Vesicular glutamate transporter 1 (VGLUT1)- and VGLUT2-immunopositive axon terminals on the rat jaw-closing and jaw-opening motoneurons.

PubMed

Park, Sook Kyung; Ko, Sang Jin; Paik, Sang Kyoo; Rah, Jong-Cheol; Lee, Kea Joo; Bae, Yong Chul

2018-02-23

To provide information on the glutamatergic synapses on the trigeminal motoneurons, which may be important for understanding the mechanism of control of jaw movements, we investigated the distribution of vesicular glutamate transporter (VGLUT)1-immunopositive (+) and VGLUT2 + axon terminals (boutons) on the rat jaw-closing (JC) and jaw-opening (JO) motoneurons, and their morphological determinants of synaptic strength by retrograde tracing, electron microscopic immunohistochemistry, and quantitative ultrastructural analysis. We found that (1) the large majority of VGLUT + boutons on JC and JO motoneurons were VGLUT2+, (2) the density of VGLUT1 + boutons terminating on JC motoneurons was significantly higher than that on JO motoneurons, (3) the density of VGLUT1 + boutons terminating on non-primary dendrites of JC motoneurons was significantly higher than that on somata or primary dendrites, whereas the density of VGLUT2 + boutons was not significantly different between JC and JO motoneurons and among various compartments of the postsynaptic neurons, and (4) the bouton volume, mitochondrial volume, and active zone area of the VGLUT1 + boutons forming synapses on JC motoneurons were significantly bigger than those of VGLUT2 + boutons. These findings suggest that JC and JO motoneurons receive glutamatergic input primarily from VGLUT2-expressing intrinsic neurons (premotoneurons), and may be controlled differently by neurons in the trigeminal mesencephalic nucleus and by glutamatergic premotoneurons.

High-power-density, high-energy-density fluorinated graphene for primary lithium batteries

NASA Astrophysics Data System (ADS)

Zhong, Guiming; Chen, Huixin; Huang, Xingkang; Yue, Hongjun; Lu, Canzhong

2018-03-01

Li/CFx is one of the highest-energy-density primary batteries; however, poor rate capability hinders its practical applications in high-power devices. Here we report a preparation of fluorinated graphene (GFx) with superior performance through a direct gas fluorination. We find that the so-called “semi-ionic” C-F bond content in all C-F bonds presents a more critical impact on rate performance of the GFx in comparison with sp2 C content in the GFx, morphology, structure, and specific surface area of the materials. The rate capability remains excellent before the semi-ionic C-F bond proportion in the GFx decreases. Thus, by optimizing semi-ionic C-F content in our GFx, we obtain the optimal x of 0.8, with which the GF0.8 exhibits a very high energy density of 1073 Wh kg-1 and an excellent power density of 21460 W kg-1 at a high current density of 10 A g-1. More importantly, our approach opens a new avenue to obtain fluorinated carbon with high energy densities without compromising high power densities.

High energy density electrochemical cell

NASA Technical Reports Server (NTRS)

Byrne, J. J.; Williams, D. L.

1970-01-01

Primary cell has an anode of lithium, a cathode containing dihaloisocyanuric acid, and a nonaqueous electrolyte comprised of a solution of lithium perchlorate in methyl formate. It produces an energy density of 213 watt hrs/lb and can achieve a high current density.

All-In-One: Advanced preparation of Human Parenchymal and Non-Parenchymal Liver Cells

PubMed Central

Werner, Melanie; Driftmann, Sabrina; Kleinehr, Kathrin; Kaiser, Gernot M.; Mathé, Zotlan; Treckmann, Juergen-Walter; Paul, Andreas; Skibbe, Kathrin; Timm, Joerg; Canbay, Ali; Gerken, Guido; Schlaak, Joerg F.; Broering, Ruth

2015-01-01

Background & Aims Liver cells are key players in innate immunity. Thus, studying primary isolated liver cells is necessary for determining their role in liver physiology and pathophysiology. In particular, the quantity and quality of isolated cells are crucial to their function. Our aim was to isolate a large quantity of high-quality human parenchymal and non-parenchymal cells from a single liver specimen. Methods Hepatocytes, Kupffer cells, liver sinusoidal endothelial cells, and stellate cells were isolated from liver tissues by collagenase perfusion in combination with low-speed centrifugation, density gradient centrifugation, and magnetic-activated cell sorting. The purity and functionality of cultured cell populations were controlled by determining their morphology, discriminative cell marker expression, and functional activity. Results Cell preparation yielded the following cell counts per gram of liver tissue: 2.0±0.4×107 hepatocytes, 1.8±0.5×106 Kupffer cells, 4.3±1.9×105 liver sinusoidal endothelial cells, and 3.2±0.5×105 stellate cells. Hepatocytes were identified by albumin (95.5±1.7%) and exhibited time-dependent activity of cytochrome P450 enzymes. Kupffer cells expressed CD68 (94.5±1.2%) and exhibited phagocytic activity, as determined with 1μm latex beads. Endothelial cells were CD146+ (97.8±1.1%) and exhibited efficient uptake of acetylated low-density lipoprotein. Hepatic stellate cells were identified by the expression of α-smooth muscle actin (97.1±1.5%). These cells further exhibited retinol (vitamin A)-mediated autofluorescence. Conclusions Our isolation procedure for primary parenchymal and non-parenchymal liver cells resulted in cell populations of high purity and quality, with retained physiological functionality in vitro. Thus, this system may provide a valuable tool for determining liver function and disease. PMID:26407160

Influence of immobilized quaternary ammonium group surface density on antimicrobial efficacy and cytotoxicity.

PubMed

Cavallaro, Alex; Mierczynska, Agnieszka; Barton, Mary; Majewski, Peter; Vasilev, Krasimir

2016-01-01

Bacterial colonization of medical devices causes infections and is a significant problem in healthcare. The use of antibacterial coatings is considered as a potential solution to this problem and has attracted a great deal of attention. Using concentration density gradients of immobilized quaternary ammonium compounds it was demonstrated that a specific threshold of surface concentration is required to induce significant bacterial death. It was determined that this threshold was 4.18% NR4(+) bonded nitrogen with a surface potential of + 120.4 mV. Furthermore, it is shown for the first time that adhesion of constituents of the culture medium to the quaternary ammonium modified surface eliminated any cytotoxicity towards eukaryotic cells such as primary human fibroblasts. The implications of this type of surface fouling on the antimicrobial efficacy of surface coatings are also discussed.

Organization, development, and effects of infraorbital nerve transection on galanin binding sites in the trigeminal brainstem complex.

PubMed

Bodie, D; Bennett-Clarke, C A; Davis, K; Postelwaite, J P; Chiaia, N L; Rhoades, R W

1997-01-01

Previous experiments from this laboratory have indicated that transection of the infraorbital nerve (ION, the trigeminal [V] branch that supplies the mystacial vibrissae follicles) at birth and in adulthood has markedly different effects on galanin immunoreactivity in the V brainstem complex. Adult nerve transection increases galanin immunoreactivity in the superficial layers of V subnucleus caudalis (SpC) only, while neonatal nerve transection results in increased galanin expression in vibrissae-related primary afferents throughout the V brainstem complex. The present study describes the distribution of binding sites for this peptide in the mature and developing V ganglion and brainstem complex and determines the effects of neonatal and adult ION damage and the associated changes in galanin levels upon their distribution and density. Galanin binding sites are densely distributed in all V brainstem subnuclei and are particularly dense in V subnucleus interpolaris and the superficial layers of SpC. They are present at birth (P-0) and their distribution is similar to that in adult animals. Transection of the ION in adulthood and examination of brainstem 7 days later indicated marked reductions in the density of galanin binding sites in the V brainstem complex. With the exception of the superficial laminae of SpC, the same reduction in density remained apparent in rats that survived > 45 days after nerve cuts. Transection of the ION on P-0 resulted in no change in the density of galanin binding sites in the brainstem after either 7 or > 60 days survival. These results indicate that densely distributed galanin binding sites are present in the V brainstem complex of both neonatal and adult rats, that they are located in regions not innervated by galanin-positive axons, and that their density is not significantly influenced by large lesion-induced changes in the primary afferent content of their natural ligand.

Tissue non-specific alkaline phosphatase production by human dental pulp stromal cells is enhanced by high density cell culture.

PubMed

Tomlinson, Matthew J; Dennis, Caitriona; Yang, Xuebin B; Kirkham, Jennifer

2015-08-01

The cell surface hydrolase tissue non-specific alkaline phosphatase (TNAP) (also known as MSCA-1) is used to identify a sub-population of bone marrow stromal cells (BMSCs) with high mineralising potential and is found on subsets of cells within the dental pulp. We aim to determine whether TNAP is co-expressed by human dental pulp stromal cells (hDPSCs) alongside a range of BMSC markers, whether this is an active form of the enzyme and the effects of culture duration and cell density on its expression. Cells from primary dental pulp and culture expanded hDPSCs expressed TNAP. Subsequent analyses revealed persistent TNAP expression and co-expression with BMSC markers such as CD73 and CD90. Flow cytometry and biochemical assays showed that increased culture durations and cell densities enhanced TNAP expression by hDPSCs. Arresting the hDPSC cell cycle also increased TNAP expression. These data confirm that TNAP is co-expressed by hDPSCs together with other BMSC markers and show that cell density affects TNAP expression levels. We conclude that TNAP is a potentially useful marker for hDPSC selection especially for uses in mineralised tissue regenerative therapies.

Experiments in free shear flows: Status and needs for the future

NASA Technical Reports Server (NTRS)

Kline, S. J.; Coles, D. E.; Eggers, J. M.; Harsha, P. T.

1973-01-01

Experiments in free turbulent flows are recommended with the primary concern placed on classical flows in order to augment understanding and for model building. Five classes of experiments dealing with classical free turbulent flows are outlined and proposed as being of particular significance for the near future. These classes include the following: (1) Experiments clarifying the effect of density variation owing to use of different gases, with and without the additional effect of density variation due to high Mach number or other effects; (2) experiments clarifying the role and importance of various parameters which determine the behavior of the near field as well as the condictions under which any of these parameters can be neglected; (3) experiments determining the cumulative effect of initial conditions in terms of distance to fully established flow; (4) experiments for cases where two layers of distinctly different initial turbulence structure flow side by side at the same mean speed; and (5) experiment using contemporary experimental techniques to study structure in free turbulent shear flows in order to compliment and support contemporary work on boundary layers.

How Adults' Access to Outpatient Physician Services Relates to the Local Supply of Primary Care Physicians in the Rural Southeast

PubMed Central

Pathman, Donald E; Ricketts, Thomas C; Konrad, Thomas R

2006-01-01

Objective To examine how access to outpatient medical care varies with local primary care physician densities across primary care service areas (PCSAs) in the rural Southeast, for adults as a whole and separately for the elderly and poor. Data Sources Access data from a 2002 to 2003 telephone survey of 4,311 adults living in 298 PCSAs within 150 rural counties in eight Southeastern states were linked geographically with physician practice location data from the American Medical and American Osteopathic Associations and population data from the U.S. Census. Study Design In a cross-sectional study design, we used a series of logistic regression models to assess how 26 measures of various aspects of access to outpatient physician services varied for subjects arranged into five groups based on the population-per-physician ratios of the PCSAs where they lived. Principal Findings Among adults as a whole, more individuals reported traveling over 30 minutes for outpatient care in PCSAs with more than 3,500 people per physician than in PCSAs with fewer than 1,500 people per physician (39.1 versus 18.5 percent, p<.001) and more reported travel difficulties. Otherwise, PCSA density of primary care physicians was unrelated to reported barriers to care, unrelated to people's satisfaction with care, and unrelated to indicators of people's use of services. Use rates of six recommended preventive health services varied in no consistent direction with physician densities. Among the elderly, only the proportion traveling over 30 minutes for care was greater in areas with lowest physician densities. Among subjects covered under Medicaid or uninsured, lower local physician densities were associated with longer travel time, difficulties with travel and reaching one's physician by phone, and two areas of dissatisfaction with care. Conclusions For adults as a whole in the rural South and for the elderly there, low local primary care physician densities are associated with travel inconvenience but not convincingly with other aspects of access to outpatient care. Access for those insured under Medicaid and the uninsured, however, is in more ways sensitive to local physician densities. PMID:16430602

Correlation between patients' reasons for encounters/health problems and population density in Japan: a systematic review of observational studies coded by the International Classification of Health Problems in Primary Care (ICHPPC) and the International Classification of Primary care (ICPC).

PubMed

Kaneko, Makoto; Ohta, Ryuichi; Nago, Naoki; Fukushi, Motoharu; Matsushima, Masato

2017-09-13

The Japanese health care system has yet to establish structured training for primary care physicians; therefore, physicians who received an internal medicine based training program continue to play a principal role in the primary care setting. To promote the development of a more efficient primary health care system, the assessment of its current status in regard to the spectrum of patients' reasons for encounters (RFEs) and health problems is an important step. Recognizing the proportions of patients' RFEs and health problems, which are not generally covered by an internist, can provide valuable information to promote the development of a primary care physician-centered system. We conducted a systematic review in which we searched six databases (PubMed, the Cochrane Library, Google Scholar, Ichushi-Web, JDreamIII and CiNii) for observational studies in Japan coded by International Classification of Health Problems in Primary Care (ICHPPC) and International Classification of Primary Care (ICPC) up to March 2015. We employed population density as index of accessibility. We calculated Spearman's rank correlation coefficient to examine the correlation between the proportion of "non-internal medicine-related" RFEs and health problems in each study area in consideration of the population density. We found 17 studies with diverse designs and settings. Among these studies, "non-internal medicine-related" RFEs, which was not thought to be covered by internists, ranged from about 4% to 40%. In addition, "non-internal medicine-related" health problems ranged from about 10% to 40%. However, no significant correlation was found between population density and the proportion of "non-internal medicine-related" RFEs and health problems. This is the first systematic review on RFEs and health problems coded by ICHPPC and ICPC undertaken to reveal the diversity of health problems in Japanese primary care. These results suggest that primary care physicians in some rural areas of Japan need to be able to deal with "non-internal-medicine-related" RFEs and health problems, and that curriculum including practical non-internal medicine-related training is likely to be important.

Analysis of ProSEDS Test of Bare-Tether Collection

NASA Technical Reports Server (NTRS)

Sanmartin, J. R.; Lorenzini, E. C.; Estes, R. D.; Charro, M.; Cosmo, M. L.

2003-01-01

NASA's tether experiment ProSEDS will be placed in orbit on board a Delta-II rocket to test bare-tether electron collection, deorbiting of the rocket second stage, and the system dynamic stability. ProSEDS performance will vary because ambient conditions change along the orbit and tether-circuit bulk elements at the cathodic end follow the step-by-step sequence for the current cycles of operating modes (open-circuit, shunt and resistor modes for primary cycles; shunt and battery modes for secondary cycles). In this work we discuss expected ProSEDS values of the ratio L,/L*, which jointly with cathodic bulk elements determines bias and current tether profiles; L, is tether length, and L* (changing with tether temperature and ionospheric plasma density and magnetic field) is a characteristic length gauging ohmic versus baretether collection impedances. We discuss how to test bare-tether electron collection during primary cycles, using probe measurements of plasma density, measurements of cathodic current in resistor and shunt modes, and an estimate of tether temperature based on ProSEDS orbital position at the particular cycle concerned. We discuss how a temperature misestimate might occasionally affect the test of bare-tether collection, and how introducing the battery mode in some primary cycles, for an additional current measurement, could obviate the need of a temperature estimate. We also show how to test bare-tether collection by estimating orbit-decay rate from measurements of cathodic current for the shunt and battery modes of secondary cycles.

Electrochemical characterization of high frequency stimulation electrodes: role of electrode material and stimulation parameters on electrode polarization

NASA Astrophysics Data System (ADS)

Ghazavi, Atefeh; Cogan, Stuart F.

2018-06-01

Objective. With recent interest in kilohertz frequency electrical stimulation for nerve conduction block, understanding the electrochemistry and role of electrode material is important for assessing the safety of these stimulus protocols. Here we describe an approach to determining electrode polarization in response to continuous kilohertz frequency sinusoidal current waveforms. We have also investigated platinum, iridium oxide, and titanium nitride as coatings for high frequency electrodes. The current density distribution at 50 kHz at the electrode–electrolyte interface was also modeled to demonstrate the importance of the primary current distribution in supporting charge injection at high frequencies. Approach. We determined electrode polarization in response to sinusoidal currents with frequencies in the 1–50 kHz range and current amplitudes from 100 to 500 µA and 1–5 mA, depending on the electrode area. The current density distribution at the interface was modeled using the finite element method (FEM). Main results. At low frequencies, 1–5 kHz, polarization on the platinum electrode was significant, exceeding the water oxidation potential for high amplitude (5 mA) waveforms. At frequencies of 20 kHz or higher, the polarization was less than 300 mV from the electrode open circuit potential. The choice of electrode material did not play a significant role in electrode polarization at frequencies higher than 10 kHz. The current density distribution modeled at 50 kHz is non-uniform and this non-uniformity persists throughout charge delivery. Significance. At high frequencies (>10 kHz) electrode double-layer charging is the principal mechanism of charge-injection and selection of the electrode material has little effect on polarization, with platinum, iridium oxide, and titanium nitride exhibiting similar behavior. High frequency stimulation is dominated by a highly nonuniform primary current distribution.

μ Eridani from MOST and from the ground: an orbit, the SPB component's fundamental parameters and the SPB frequencies

NASA Astrophysics Data System (ADS)

Jerzykiewicz, M.; Lehmann, H.; Niemczura, E.; Molenda-Żakowicz, J.; Dymitrov, W.; Fagas, M.; Guenther, D. B.; Hartmann, M.; Hrudková, M.; Kamiński, K.; Moffat, A. F. J.; Kuschnig, R.; Leto, G.; Matthews, J. M.; Rowe, J. F.; Ruciński, S. M.; Sasselov, D.; Weiss, W. W.

2013-06-01

MOST time series photometry of μ Eri, an SB1 eclipsing binary with a rapidly rotating SPB primary, is reported and analysed. The analysis yields a number of sinusoidal terms, mainly due to the intrinsic variation of the primary, and the eclipse light curve. New radial-velocity observations are presented and used to compute parameters of a spectroscopic orbit. Frequency analysis of the radial-velocity residuals from the spectroscopic orbital solution fails to uncover periodic variations with amplitudes greater than 2 km s-1. A Rossiter-McLaughlin anomaly is detected from observations covering ingress. From archival photometric indices and the revised Hipparcos parallax, we derive the primary's effective temperature, surface gravity, bolometric correction and the luminosity. An analysis of a high signal-to-noise spectrogram yields the effective temperature and surface gravity in good agreement with the photometric values. From the same spectrogram, we determine the abundance of He, C, N, O, Ne, Mg, Al, Si, P, S, Cl and Fe. The eclipse light curve is solved by means of EBOP. For a range of mass of the primary, a value of mean density, very nearly independent of assumed mass, is computed from the parameters of the system. Contrary to a recent report, this value is approximately equal to the mean density obtained from the star's effective temperature and luminosity. Despite limited frequency resolution of the MOST data, we were able to recover the closely spaced SPB frequency quadruplet discovered from the ground in 2002-2004. The other two SPB terms seen from the ground were also recovered. Moreover, our analysis of the MOST data adds 15 low-amplitude SPB terms with frequencies ranging from 0.109 to 2.786 d-1.

Nuclear density evaluation on asphaltic concrete: final report.

DOT National Transportation Integrated Search

1967-04-01

This study was one of two studies designated as Research Project 62-1SB to evaluate the use of nuclear devices in highway construction. (1) The primary objective of this study was to evaluate a nuclear density device for obtaining densities on asphal...

16 CFR 1209.4 - Test procedures for determining settled density.

Code of Federal Regulations, 2012 CFR

2012-01-01

... density. 1209.4 Section 1209.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... procedures for determining settled density. The settled density of lose fill insulation must be determined.... This section describes the procedure for determining the settled density of loose fill insulation. (a...

16 CFR 1209.4 - Test procedures for determining settled density.

Code of Federal Regulations, 2014 CFR

2014-01-01

... density. 1209.4 Section 1209.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... procedures for determining settled density. The settled density of lose fill insulation must be determined.... This section describes the procedure for determining the settled density of loose fill insulation. (a...

16 CFR 1209.4 - Test procedures for determining settled density.

Code of Federal Regulations, 2011 CFR

2011-01-01

... density. 1209.4 Section 1209.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... procedures for determining settled density. The settled density of lose fill insulation must be determined.... This section describes the procedure for determining the settled density of loose fill insulation. (a...

16 CFR 1209.4 - Test procedures for determining settled density.

Code of Federal Regulations, 2010 CFR

2010-01-01

... density. 1209.4 Section 1209.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... procedures for determining settled density. The settled density of lose fill insulation must be determined.... This section describes the procedure for determining the settled density of loose fill insulation. (a...

Controlled cell morphology and liver-specific function of engineered primary hepatocytes by fibroblast layer cell densities.

PubMed

Sakai, Yusuke; Koike, Makiko; Kawahara, Daisuke; Hasegawa, Hideko; Murai, Tomomi; Yamanouchi, Kosho; Soyama, Akihiko; Hidaka, Masaaki; Takatsuki, Mitsuhisa; Fujita, Fumihiko; Kuroki, Tamotsu; Eguchi, Susumu

2018-03-05

Engineered primary hepatocytes, including co-cultured hepatocyte sheets, are an attractive to basic scientific and clinical researchers because they maintain liver-specific functions, have reconstructed cell polarity, and have high transplantation efficiency. However, co-culture conditions regarding engineered primary hepatocytes were suboptimal in promoting these advantages. Here we report that the hepatocyte morphology and liver-specific function levels are controlled by the normal human diploid fibroblast (TIG-118 cell) layer cell density. Primary rat hepatocytes were plated onto TIG-118 cells, previously plated 3 days before at 1.04, 5.21, and 26.1×10 3  cells/cm 2 . Hepatocytes plated onto lower TIG-118 cell densities expanded better during the early culture period. The hepatocytes gathered as colonies and only exhibited small adhesion areas because of the pushing force from proliferating TIG-118 cells. The smaller areas of each hepatocyte result in the development of bile canaliculi. The highest density of TIG-118 cells downregulated albumin synthesis activity of hepatocytes. The hepatocytes may have undergone apoptosis associated with high TGF-β1 concentration and necrosis due to a lack of oxygen. These occurrences were supported by apoptotic chromatin condensation and high expression of both proteins HIF-1a and HIF-1b. Three types of engineered hepatocyte/fibroblast sheets comprising different TIG-118 cell densities were harvested after 4 days of hepatocyte culture and showed a complete cell sheet format without any holes. Hepatocyte morphology and liver-specific function levels are controlled by TIG-118 cell density, which helps to design better engineered hepatocytes for future applications such as in vitro cell-based assays and transplantable hepatocyte tissues. Copyright © 2018 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Primary productivity by phytoplankton in the tidal, fresh Potomac River, Maryland, May 1980 to August 1981

USGS Publications Warehouse

Cohen, R.R.; Pollock, S.O.

1983-01-01

Primary productivity by phytoplankton was measured on samples collected from the Potomac Tidal River, Maryland. The studies were performed monthly from May 1980 to September 1981. Additional studies were done once a week in August 1980, twice a week from August 4 to 8, 1980 and twice in September 1980. Depth-integrated samples were collected at five stations and incubated in boxes that were exposed to natural sunlight. The boxes were covered with neutral density filters transmitting 100 , 65, 32, 16, and 6 percent surface light. River water was pumped continuously over the samples. The extinction of light in the water column by phytoplankton was measured when samples were collected. Experiments were performed to select a method for routine productivity analysis. No difference was found between productivity: (1) determined in situ and in boxes; (2) measured in 300 ml and (4) calculated from short term (4 hours) and long term (10-24 hours) incubations. There were higher productivity differences in samples that were rotated among different light intensities every 15 minutes (simulating mixing) than those remaining stationary. Respiration was significantly less in samples pumped through a hose from those collected using a depth-integrating sampler. Depth-integrated primary productivity was determined from the productivity data using an equation modified from one reported in the literature. Depth-integrated gross primary productivity was highest in August 1980 and 1981 and lowest in January 1980. (USGS)

Integration of high capacity materials into interdigitated mesostructured electrodes for high energy and high power density primary microbatteries

NASA Astrophysics Data System (ADS)

Pikul, James H.; Liu, Jinyun; Braun, Paul V.; King, William P.

2016-05-01

Microbatteries are increasingly important for powering electronic systems, however, the volumetric energy density of microbatteries lags behind that of conventional format batteries. This paper reports a primary microbattery with energy density 45.5 μWh cm-2 μm-1 and peak power 5300 μW cm-2 μm-1, enabled by the integration of large volume fractions of high capacity anode and cathode chemistry into porous micro-architectures. The interdigitated battery electrodes consist of a lithium metal anode and a mesoporous manganese oxide cathode. The key enabler of the high energy and power density is the integration of the high capacity manganese oxide conversion chemistry into a mesostructured high power interdigitated bicontinuous cathode architecture and an electrodeposited dense lithium metal anode. The resultant energy density is greater than previously reported three-dimensional microbatteries and is comparable to commercial conventional format lithium-based batteries.

16 CFR § 1209.4 - Test procedures for determining settled density.

Code of Federal Regulations, 2013 CFR

2013-01-01

... density. § 1209.4 Section § 1209.4 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER... procedures for determining settled density. The settled density of lose fill insulation must be determined.... This section describes the procedure for determining the settled density of loose fill insulation. (a...

Effect on bone density of postoperative calcium and vitamin-D supplementation in patients with primary hyperparathyroidism: A retrospective study.

PubMed

Nordenström, Erik; Westerdahl, Johan; Bergenfelz, Anders

2009-05-01

Primary hyperparathyroidism (pHPT) is associated with decreased bone density and increased fracture risk. A significant number of pHPT patients have low calcium intake and suffer from vitamin deficiency. Thus, we adopted a policy of postoperative supplements with calcium and vitamin D after parathyroid surgery. In this study, we investigated if this policy enhanced the postoperative increase in bone density. Forty-two consecutive patients (83% female) were studied. The first 21 patients received no supplements, whereas the following 21 patients received 1,000 g calcium and 800 IU hydroxy D: -vitamin daily (Ca-D group) for 1 year postoperatively. The patients were monitored with bone density and biochemistry pre- and at 1 year postoperatively. Preoperatively, the patients without vitamin D supplementation (non-Ca-D group) did neither differ in biochemistry, clinical features, nor in bone density from patients in Ca-D group. Postoperatively, there was a tendency that patients in Ca-D group increased their bone density, at all sites measured, in a greater extent than patients that did not receive calcium and vitamin D supplementation. In conclusion, based on our results, it is difficult to give a recommendation of vitamin D supplementation in routine use following surgery for primary hyperparathyroidism. Based on the present data, a calculation of sample size for a future randomized controlled trial is presented.

Experimental study of the maximum resolution and packing density achievable in sintered and non-sintered binder-jet 3D printed steel microchannels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, Amy M; Mehdizadeh Momen, Ayyoub; Benedict, Michael

2015-01-01

Developing high resolution 3D printed metallic microchannels is a challenge especially when there is an essential need for high packing density of the primary material. While high packing density could be achieved by heating the structure to the sintering temperature, some heat sensitive applications require other strategies to improve the packing density of primary materials. In this study the goal is to develop high green or pack densities microchannels on the scale of 2-300 microns which have a robust mechanical structure. Binder-jet 3D printing is an additive manufacturing process in which droplets of binder are deposited via inkjet into amore » bed of powder. By repeatedly spreading thin layers of powder and depositing binder into the appropriate 2D profiles, complex 3D objects can be created one layer at time. Microchannels with features on the order of 500 microns were fabricated via binder jetting of steel powder and then sintered and/or infiltrated with a secondary material. The average particle size of the steel powder was varied along with the droplet volume of the inkjet-deposited binder. The resolution of the process, packing density of the primary material, the subsequent features sizes of the microchannels, and the overall microchannel quality were characterized as a function of particle size distribution, droplet sizes and heat treatment temperatures.« less

High follicle density does not decrease sweat gland density in Huacaya alpacas.

PubMed

Moore, K E; Maloney, S K; Blache, D

2015-01-01

When exposed to high ambient temperatures, mammals lose heat evaporatively by either sweating from glands in the skin or by respiratory panting. Like other camelids, alpacas are thought to evaporate more water by sweating than panting, despite a thick fleece, unlike sheep which mostly pant in response to heat stress. Alpacas were brought to Australia to develop an alternative fibre industry to sheep wool. In Australia, alpacas can be exposed to ambient temperatures higher than in their native South America. As a young industry there is a great deal of variation in the quality and quantity of the fleece produced in the national flock. There is selection pressure towards animals with finer and denser fleeces. Because the fibre from secondary follicles is finer than that from primary follicles, selecting for finer fibres might alter the ratio of primary and secondary follicles. In turn the selection might alter sweat gland density because the sweat glands are associated with the primary follicle. Skin biopsy and fibre samples were obtained from the mid-section of 33 Huacaya alpacas and the skin sections were processed into horizontal sections at the sebaceous gland level. Total, primary, and secondary follicles and the number of sweat gland ducts were quantified. Fibre samples from each alpaca were further analysed for mean fibre diameter. The finer-fibred animals had a higher total follicle density (P<0.001) and more sweat glands (P<0.001) than the thicker-fibred animals. The fibre diameter and total follicle density were negatively correlated (R(2)=0.56, P<0.001). Given that the finer-fibred animals had higher follicle density and more sweat glands than animals with thicker fibres, we conclude that alpacas with high follicle density should not be limited for potential sweating ability. Copyright © 2014 Elsevier Ltd. All rights reserved.

Lithium Sulfur Primary Battery with Super High Energy Density: Based on the Cauliflower-like Structured C/S Cathode

NASA Astrophysics Data System (ADS)

Ma, Yiwen; Zhang, Hongzhang; Wu, Baoshan; Wang, Meiri; Li, Xianfeng; Zhang, Huamin

2015-10-01

The lithium-sulfur primary batteries, as seldom reported in the previous literatures, were developed in this work. In order to maximize its practical energy density, a novel cauliflower-like hierarchical porous C/S cathode was designed, for facilitating the lithium-ions transport and sulfur accommodation. This kind of cathode could release about 1300 mAh g-1 (S) capacity at sulfur loading of 6 ~ 14 mg cm-2, and showed excellent shelf stability during a month test at room temperature. As a result, the assembled Li-S soft package battery achieved an energy density of 504 Wh kg-1 (654 Wh L-1), which was the highest value ever reported to the best of our knowledge. This work might arouse the interests on developing primary Li-S batteries, with great potential for practical application.

Lithium Sulfur Primary Battery with Super High Energy Density: Based on the Cauliflower-like Structured C/S Cathode.

PubMed

Ma, Yiwen; Zhang, Hongzhang; Wu, Baoshan; Wang, Meiri; Li, Xianfeng; Zhang, Huamin

2015-10-12

The lithium-sulfur primary batteries, as seldom reported in the previous literatures, were developed in this work. In order to maximize its practical energy density, a novel cauliflower-like hierarchical porous C/S cathode was designed, for facilitating the lithium-ions transport and sulfur accommodation. This kind of cathode could release about 1300 mAh g(-1) (S) capacity at sulfur loading of 6 ~ 14 mg cm(-2), and showed excellent shelf stability during a month test at room temperature. As a result, the assembled Li-S soft package battery achieved an energy density of 504 Wh kg(-1) (654 Wh L(-1)), which was the highest value ever reported to the best of our knowledge. This work might arouse the interests on developing primary Li-S batteries, with great potential for practical application.

Lithium Sulfur Primary Battery with Super High Energy Density: Based on the Cauliflower-like Structured C/S Cathode

PubMed Central

Ma, Yiwen; Zhang, Hongzhang; Wu, Baoshan; Wang, Meiri; Li, Xianfeng; Zhang, Huamin

2015-01-01

The lithium-sulfur primary batteries, as seldom reported in the previous literatures, were developed in this work. In order to maximize its practical energy density, a novel cauliflower-like hierarchical porous C/S cathode was designed, for facilitating the lithium-ions transport and sulfur accommodation. This kind of cathode could release about 1300 mAh g−1 (S) capacity at sulfur loading of 6 ~ 14 mg cm−2, and showed excellent shelf stability during a month test at room temperature. As a result, the assembled Li-S soft package battery achieved an energy density of 504 Wh kg−1 (654 Wh L−1), which was the highest value ever reported to the best of our knowledge. This work might arouse the interests on developing primary Li-S batteries, with great potential for practical application. PMID:26456914

Bone Density and Timing of Puberty in a Longitudinal Study of Girls.

PubMed

Cattran, Ashley M; Kalkwarf, Heidi J; Pinney, Susan M; Huang, Bin; Biro, Frank M

2015-06-01

Primary: To examine the relationship between relative timing of puberty with bone mineral density (BMD) in a group of adolescent girls; Secondary: To determine if family history of breast cancer was associated with bone mineral density. Longitudinal study of girls recruited between 6 and 7 years of age seen every 6 months for 5 years, and subsequently seen annually. BMD of the lumbar spine was measured by dual-energy X-ray absorptiometry (DXA) at mean age of 12.5 years; age- and race-specific Z-scores (BMDz) were calculated. Age of pubertal onset was determined by the first occurrence of breast stage 2, and participants were categorized into race-specific early, on-time and late puberty onset groups. BMDz by timing of pubertal onset, and by family history of breast cancer. DXA scans were performed on 227 study participants, and a second scan was performed on 114 participants 2 years later. Age of onset of puberty was inversely correlated with BMDz, r = -0.31 (P < .0001). There was no association between BMDz and family history of breast cancer. Earlier timing of puberty was associated with higher BMD. The high shared variance of BMD and timing of pubertal onset implies an underlying biologic basis. Copyright © 2015 North American Society for Pediatric and Adolescent Gynecology. Published by Elsevier Inc. All rights reserved.

Cross-sectional study of patients with type 2 diabetes in OR Tambo district, South Africa

PubMed Central

Yogeswaran, Parimalaranie; Longo-Mbenza, Benjamin; Ter Goon, Daniel; Ajayi, Anthony Idowu

2016-01-01

Objectives South Africa has pledged to the sustainable development goal of promoting good health and well-being to all residents. While this is laudable, paucity of reliable epidemiological data for different regions on diabetes and treatment outcomes may further widen the inequalities of access and quality of healthcare services across the country. This study examines the sociodemographic and clinical determinants of uncontrolled type 2 diabetes mellitus (T2DM) in individuals attending primary healthcare in OR Tambo district, South Africa. Design A cross-sectional analytical study. Setting Primary healthcare setting in OR Tambo district, South Africa. Participants Patients treated for T2DM for 1 or more years (n=327). Primary outcome measure Prevalence of uncontrolled T2DM. Secondary outcome measure Determinants of uncontrolled T2DM (glycosylated haemoglobin (HbA1c) ≥7%). Results Out of the 327 participants, 274 had HbA1c≥7% (83.8%). Female sex (95% CI 1.3 to 4.2), overweight/obesity (95% CI 1.9 to 261.2), elevated low-density lipoprotein cholesterol (95% CI 4.4 to 23.8), sedentary habits (95% CI 7.2 to 61.3), lower monthly income (95% CI 1.3 to 6.5), longer duration of T2DM (95% CI 4.4 to 294.2) and diabetes information from non-health workers (95% CI 1.4 to 7.0) were the significant determinants of uncontrolled T2DM. There was a significant positive correlation of uncontrolled T2DM with increasing duration of T2DM, estimated glomerular filtration rate and body mass index. However, a significant negative correlation exists between monthly income and increasing HbA1c. Conclusions We found a significantly high prevalence (83.8%) of uncontrolled T2DM among the patients, possibly attributable to overweight/obesity, sedentary living, lower income and lack of information on diabetes. Addressing these determinants will require re-engineering of primary healthcare in the district. PMID:27473948

Chimpanzees in an anthropogenic landscape: Examining food resources across habitat types at Bossou, Guinea, West Africa.

PubMed

Bryson-Morrison, Nicola; Matsuzawa, Tetsuro; Humle, Tatyana

2016-12-01

Many primate populations occur outside protected areas in fragmented anthropogenic landscapes. Empirical data on the ecological characteristics that define an anthropogenic landscape are urgently required if conservation initiatives in such environments are to succeed. The main objective of our study was to determine the composition and availability of chimpanzee (Pan troglodytes verus) food resources across fine spatial scales in the anthropogenic landscape of Bossou, Guinea, West Africa. We examined food resources in all habitat types available in the chimpanzees' core area. We surveyed resource composition, structure and heterogeneity (20 m × 20 m quadrats, N = 54) and assessed temporal availability of food from phenology trails (total distance 5951 m; 1073 individual trees) over 1 year (2012-2013). Over half of Bossou consists of regenerating forest and is highly diverse in terms of chimpanzee food species; large fruit bearing trees are rare and confined to primary and riverine forest. Moraceae (mulberries and figs) was the dominant family, trees of which produce drupaceous fruits favored by chimpanzees. The oil palm occurs at high densities throughout and is the only species found in all habitat types except primary forest. Our data suggest that the high densities of oil palm and fig trees, along with abundant terrestrial herbaceous vegetation and cultivars, are able to provide the chimpanzees with widely available resources, compensating for the scarcity of large fruit trees. A significant difference was found between habitat types in stem density/ha and basal area m 2 /ha of chimpanzee food species. Secondary, young secondary, and primary forest emerged as the most important habitat types for availability of food tree species. Our study emphasizes the importance of examining ecological characteristics of an anthropogenic landscape as each available habitat type is unlikely to be equally important in terms of spatial and temporal availability of resources. Am. J. Primatol. 78:1237-1249, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Revealing Relationships among Relevant Climate Variables with Information Theory

NASA Technical Reports Server (NTRS)

Knuth, Kevin H.; Golera, Anthony; Curry, Charles T.; Huyser, Karen A.; Kevin R. Wheeler; Rossow, William B.

2005-01-01

The primary objective of the NASA Earth-Sun Exploration Technology Office is to understand the observed Earth climate variability, thus enabling the determination and prediction of the climate's response to both natural and human-induced forcing. We are currently developing a suite of computational tools that will allow researchers to calculate, from data, a variety of information-theoretic quantities such as mutual information, which can be used to identify relationships among climate variables, and transfer entropy, which indicates the possibility of causal interactions. Our tools estimate these quantities along with their associated error bars, the latter of which is critical for describing the degree of uncertainty in the estimates. This work is based upon optimal binning techniques that we have developed for piecewise-constant, histogram-style models of the underlying density functions. Two useful side benefits have already been discovered. The first allows a researcher to determine whether there exist sufficient data to estimate the underlying probability density. The second permits one to determine an acceptable degree of round-off when compressing data for efficient transfer and storage. We also demonstrate how mutual information and transfer entropy can be applied so as to allow researchers not only to identify relations among climate variables, but also to characterize and quantify their possible causal interactions.

The B-Raf status of tumor cells may be a significant determinant of both antitumor and anti-angiogenic effects of pazopanib in xenograft tumor models.

PubMed

Gril, Brunilde; Palmieri, Diane; Qian, Yong; Anwar, Talha; Ileva, Lilia; Bernardo, Marcelino; Choyke, Peter; Liewehr, David J; Steinberg, Seth M; Steeg, Patricia S

2011-01-01

Pazopanib is an FDA approved Vascular Endothelial Growth Factor Receptor inhibitor. We previously reported that it also inhibits tumor cell B-Raf activity in an experimental brain metastatic setting. Here, we determine the effects of different B-Raf genotypes on pazopanib efficacy, in terms of primary tumor growth and anti-angiogenesis. A panel of seven human breast cancer and melanoma cell lines harboring different mutations in the Ras-Raf pathway was implanted orthotopically in mice, and tumor growth, ERK1/2, MEK1/2 and AKT activation, and blood vessel density and permeability were analyzed. Pazopanib was significantly inhibitory to xenografts expressing either exon 11 mutations of B-Raf, or HER2 activated wild type B-Raf; no significant inhibition of a xenograft expressing the common V600E B-Raf mutation was observed. Decreased pMEK staining in the responsive tumors confirmed that B-Raf was targeted by pazopanib. Interestingly, pazopanib inhibition of tumor cell B-Raf also correlated with its anti-angiogenic activity, as quantified by vessel density and area. In conclusion, using pazopanib, tumor B-Raf status was identified as a significant determinant of both tumor growth and angiogenesis.

The B-Raf Status of Tumor Cells May Be a Significant Determinant of Both Antitumor and Anti-Angiogenic Effects of Pazopanib in Xenograft Tumor Models

PubMed Central

Gril, Brunilde; Palmieri, Diane; Qian, Yong; Anwar, Talha; Ileva, Lilia; Bernardo, Marcelino; Choyke, Peter; Liewehr, David J.; Steinberg, Seth M.; Steeg, Patricia S.

2011-01-01

Pazopanib is an FDA approved Vascular Endothelial Growth Factor Receptor inhibitor. We previously reported that it also inhibits tumor cell B-Raf activity in an experimental brain metastatic setting. Here, we determine the effects of different B-Raf genotypes on pazopanib efficacy, in terms of primary tumor growth and anti-angiogenesis. A panel of seven human breast cancer and melanoma cell lines harboring different mutations in the Ras-Raf pathway was implanted orthotopically in mice, and tumor growth, ERK1/2, MEK1/2 and AKT activation, and blood vessel density and permeability were analyzed. Pazopanib was significantly inhibitory to xenografts expressing either exon 11 mutations of B-Raf, or HER2 activated wild type B-Raf; no significant inhibition of a xenograft expressing the common V600E B-Raf mutation was observed. Decreased pMEK staining in the responsive tumors confirmed that B-Raf was targeted by pazopanib. Interestingly, pazopanib inhibition of tumor cell B-Raf also correlated with its anti-angiogenic activity, as quantified by vessel density and area. In conclusion, using pazopanib, tumor B-Raf status was identified as a significant determinant of both tumor growth and angiogenesis. PMID:21998674

Quality Assurance for Rapid Airfield Construction

DTIC Science & Technology

2008-05-01

necessary to conduct a volume-replacement density test for in-place soil. This density test, which was developed during this investigation, involves...the test both simpler and quicker. The Clegg hammer results are the primary means of judging compaction; thus, the requirements for density tests are...minimized through a stepwise acceptance procedure. Statistical criteria for evaluating Clegg hammer and density measurements are also included

Evolution of mixing width induced by general Rayleigh-Taylor instability.

PubMed

Zhang, You-Sheng; He, Zhi-Wei; Gao, Fu-Jie; Li, Xin-Liang; Tian, Bao-Lin

2016-06-01

Turbulent mixing induced by Rayleigh-Taylor (RT) instability occurs ubiquitously in many natural phenomena and engineering applications. As the simplest and primary descriptor of the mixing process, the evolution of mixing width of the mixing zone plays a notable role in the flows. The flows generally involve complex varying acceleration histories and widely varying density ratios, two dominant factors affecting the evolution of mixing width. However, no satisfactory theory for predicting the evolution has yet been established. Here a theory determining the evolution of mixing width in general RT flows is established to reproduce, first, all of the documented experiments conducted for diverse (i.e., constant, impulsive, oscillating, decreasing, increasing, and complex) acceleration histories and all density ratios. The theory is established in terms of the conservation principle, with special consideration given to the asymmetry of the volume-averaged density fields occurring in actual flows. The results reveal the sensitivity or insensitivity of the evolution of a mixing front of a neighboring light or heavy fluid to the degree of asymmetry and thus explain the distinct evolutions in two experiments with the same configurations.

Proximate analysis, in vitro organic matter digestibility, and energy content of common guava (Psidium guajava L.) and yellow, strawberry guava (Psidium cattleianum Var. lucidum) tree parts and fruits as potential forage.

PubMed

Adrian, Julie Ann Luiz; Arancon, Norman Q; Mathews, Bruce W; Carpenter, James R

2012-10-24

The nutrient composition of common guava, Psidium guajava L., and strawberry guava (waiwi), Psidium cattleianum var. lucidum, tree parts and fruits was determined during three seasons for six locations in Hawaii to assess guava as a potential feed for cattle. All guava plant parts were higher (p < 0.001) in crude protein than waiwi, but there were no differences in the fiber and energy densities for bark, shoots, and branches. Guava leaves were higher in fiber and had lower energy densities (p < 0.05) than waiwi. Ripe and breaker stage fruits were lower (p < 0.05) in fiber, similar in protein (CP), and higher (p < 0.05) in energy density than immature fruits. Guava fruits were higher in CP (p < 0.05) and organic matter (p < 0.001) and lower in ash (p < 0.001) than waiwi fruits. The primary nutritional concern with guava is low in vitro organic matter digestibility as compared to tropical forage grasses; therefore, it is not recommended as a feedstock for livestock.

Automatic Whistler Detector and Analyzer system: Implementation of the analyzer algorithm

NASA Astrophysics Data System (ADS)

Lichtenberger, JáNos; Ferencz, Csaba; Hamar, Daniel; Steinbach, Peter; Rodger, Craig J.; Clilverd, Mark A.; Collier, Andrew B.

2010-12-01

The full potential of whistlers for monitoring plasmaspheric electron density variations has not yet been realized. The primary reason is the vast human effort required for the analysis of whistler traces. Recently, the first part of a complete whistler analysis procedure was successfully automated, i.e., the automatic detection of whistler traces from the raw broadband VLF signal was achieved. This study describes a new algorithm developed to determine plasmaspheric electron density measurements from whistler traces, based on a Virtual (Whistler) Trace Transformation, using a 2-D fast Fourier transform transformation. This algorithm can be automated and can thus form the final step to complete an Automatic Whistler Detector and Analyzer (AWDA) system. In this second AWDA paper, the practical implementation of the Automatic Whistler Analyzer (AWA) algorithm is discussed and a feasible solution is presented. The practical implementation of the algorithm is able to track the variations of plasmasphere in quasi real time on a PC cluster with 100 CPU cores. The electron densities obtained by the AWA method can be used in investigations such as plasmasphere dynamics, ionosphere-plasmasphere coupling, or in space weather models.

Microstructurally-sensitive fatigue crack nucleation in Ni-based single and oligo crystals

NASA Astrophysics Data System (ADS)

Chen, Bo; Jiang, Jun; Dunne, Fionn P. E.

2017-09-01

An integrated experimental, characterisation and computational crystal plasticity study of cyclic plastic beam loading has been carried out for nickel single crystal (CMSX4) and oligocrystal (MAR002) alloys in order to assess quantitatively the mechanistic drivers for fatigue crack nucleation. The experimentally validated modelling provides knowledge of key microstructural quantities (accumulated slip, stress and GND density) at experimentally observed fatigue crack nucleation sites and it is shown that while each of these quantities is potentially important in crack nucleation, none of them in its own right is sufficient to be predictive. However, the local (elastic) stored energy density, measured over a length scale determined by the density of SSDs and GNDs, has been shown to predict crack nucleation sites in the single and oligocrystals tests. In addition, once primary nucleated cracks develop and are represented in the crystal model using XFEM, the stored energy correctly identifies where secondary fatigue cracks are observed to nucleate in experiments. This (Griffith-Stroh type) quantity also correctly differentiates and explains intergranular and transgranular fatigue crack nucleation.

Particle based plasma simulation for an ion engine discharge chamber

NASA Astrophysics Data System (ADS)

Mahalingam, Sudhakar

Design of the next generation of ion engines can benefit from detailed computer simulations of the plasma in the discharge chamber. In this work a complete particle based approach has been taken to model the discharge chamber plasma. This is the first time that simplifying continuum assumptions on the particle motion have not been made in a discharge chamber model. Because of the long mean free paths of the particles in the discharge chamber continuum models are questionable. The PIC-MCC model developed in this work tracks following particles: neutrals, singly charged ions, doubly charged ions, secondary electrons, and primary electrons. The trajectories of these particles are determined using the Newton-Lorentz's equation of motion including the effects of magnetic and electric fields. Particle collisions are determined using an MCC statistical technique. A large number of collision processes and particle wall interactions are included in the model. The magnetic fields produced by the permanent magnets are determined using Maxwell's equations. The electric fields are determined using an approximate input electric field coupled with a dynamic determination of the electric fields caused by the charged particles. In this work inclusion of the dynamic electric field calculation is made possible by using an inflated plasma permittivity value in the Poisson solver. This allows dynamic electric field calculation with minimal computational requirements in terms of both computer memory and run time. In addition, a number of other numerical procedures such as parallel processing have been implemented to shorten the computational time. The primary results are those modeling the discharge chamber of NASA's NSTAR ion engine at its full operating power. Convergence of numerical results such as total number of particles inside the discharge chamber, average energy of the plasma particles, discharge current, beam current and beam efficiency are obtained. Steady state results for the particle number density distributions and particle loss rates to the walls are presented. Comparisons of numerical results with experimental measurements such as currents and the particle number density distributions are made. Results from a parametric study and from an alternative magnetic field design are also given.

Integrated economic and experimental framework for screening of primary recovery technologies for high cell density CHO cultures

PubMed Central

Popova, Daria; Stonier, Adam; Pain, David; Titchener‐Hooker, Nigel J.

2016-01-01

Abstract Increases in mammalian cell culture titres and densities have placed significant demands on primary recovery operation performance. This article presents a methodology which aims to screen rapidly and evaluate primary recovery technologies for their scope for technically feasible and cost‐effective operation in the context of high cell density mammalian cell cultures. It was applied to assess the performance of current (centrifugation and depth filtration options) and alternative (tangential flow filtration (TFF)) primary recovery strategies. Cell culture test materials (CCTM) were generated to simulate the most demanding cell culture conditions selected as a screening challenge for the technologies. The performance of these technology options was assessed using lab scale and ultra scale‐down (USD) mimics requiring 25–110mL volumes for centrifugation and depth filtration and TFF screening experiments respectively. A centrifugation and depth filtration combination as well as both of the alternative technologies met the performance selection criteria. A detailed process economics evaluation was carried out at three scales of manufacturing (2,000L, 10,000L, 20,000L), where alternative primary recovery options were shown to potentially provide a more cost‐effective primary recovery process in the future. This assessment process and the study results can aid technology selection to identify the most effective option for a specific scenario. PMID:27067803

Relationships between ecosystem metabolism, benthic macroinvertebrate densities, and environmental variables in a sub-arctic Alaskan river

USGS Publications Warehouse

Benson, Emily R.; Wipfli, Mark S.; Clapcott, Joanne E.; Hughes, Nicholas F.

2013-01-01

Relationships between environmental variables, ecosystem metabolism, and benthos are not well understood in sub-arctic ecosystems. The goal of this study was to investigate environmental drivers of river ecosystem metabolism and macroinvertebrate density in a sub-arctic river. We estimated primary production and respiration rates, sampled benthic macroinvertebrates, and monitored light intensity, discharge rate, and nutrient concentrations in the Chena River, interior Alaska, over two summers. We employed Random Forests models to identify predictor variables for metabolism rates and benthic macroinvertebrate density and biomass, and calculated Spearman correlations between in-stream nutrient levels and metabolism rates. Models indicated that discharge and length of time between high water events were the most important factors measured for predicting metabolism rates. Discharge was the most important variable for predicting benthic macroinvertebrate density and biomass. Primary production rate peaked at intermediate discharge, respiration rate was lowest at the greatest time since last high water event, and benthic macroinvertebrate density was lowest at high discharge rates. The ratio of dissolved inorganic nitrogen to soluble reactive phosphorus ranged from 27:1 to 172:1. We found that discharge plays a key role in regulating stream ecosystem metabolism, but that low phosphorous levels also likely limit primary production in this sub-arctic stream.

Response of amphibian egg cytoplasm to novel gravity orientation and centrifugation

NASA Technical Reports Server (NTRS)

Neff, A. W.; Wakahara, M.; Jurand, A.; Malacinski, G. M.

1983-01-01

The effects of inversion and centrifugation on the compartmentalization of cytoplasm in Xenopus laevis eggs are investigated experimentally. The rearrangement of yolk-platelet compartments (YPC) characterized by morphology, density, and viscosity differences is studied in fertilized, unfertilized, and unfertilized electrically activated eggs in normal, and inverted positions and with and without centrifugation at 10-183 x g for 5 min. The eggs are fixed and embedded in plastic or paraffin prior to sagittal sectioning (0.5, 4, or 8 microns) and microscopic examination; the results are presented in a diagram and discussed. A density-compartment model combining both animal/vegetal and dorsal/ventral polarities is proposed: YPC determined without gravity orientation during oogenesis respond to both sperm entrance point and gravity after fertilization, and the response involves breaking of the radial symmetry of the egg. It is predicted that Xenopus eggs in a microgravity environment will encounter difficulties in establishing a primary embryonic axis.

Characterization of solidifiers used for oil spill remediation.

PubMed

Sundaravadivelu, Devi; Suidan, Makram T; Venosa, Albert D; Rosales, Pablo I

2016-02-01

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial products were primarily comprised of organic polymers and a few trace elements. A natural sorbent, which was composed entirely of plant based matter, was also evaluated, and it had the highest oil removal capacity, but it did not produce a solid mat-like final product. Generally, solidifiers with a carbonate group, pore size greater than 5 μm, and bulk densities lower than 0.3 g cm(-3) were found to have better efficiency and produced a cohesive rubbery final product that facilitated removal compared to sorbents. The importance of bulk density and pore size in the performance of the solidifier suggest that the primary mechanism of action was likely physical sorption. Copyright © 2015 Elsevier Ltd. All rights reserved.

Microplastic in three urban estuaries, China.

PubMed

Zhao, Shiye; Zhu, Lixin; Li, Daoji

2015-11-01

Estuarine Microplastics (MPs) are limited to know globally. By filtering subsurface water through 330 μm nets, MPs in Jiaojiang, Oujiang Estuaries were quantified, as well as that in Minjiang Estuary responding to Typhoon Soulik. Polymer matrix was analyzed by Raman spectroscopy. MP (<5 mm) comprised more than 90% of total number plastics. The highest MPs density was found in Minjiang, following Jiaojiang and Oujiang. Fibers and granules were the primary shapes, with no pellets found. Colored MPs were the majority. The concentrations of suspended microplastics determine their bioavailability to low trophic organisms, and then possibly promoting the transfer of microplastic to higher trophic levels. Polypropylene and polyethylene were the prevalent types of MPs analyzed. Economic structures in urban estuaries influenced on MPs contamination levels. Typhoon didn't influence the suspended MP densities significantly. Our results provide basic information for better understanding suspended microplastics within urban estuaries and for managerial actions. Copyright © 2015. Published by Elsevier Ltd.

Inverted-V events simultaneously observed with the Freja satellite and from the ground

NASA Astrophysics Data System (ADS)

Haerendel, G.; Frey, H. U.; Bauer, O. H.; Rieger, E.; Clemmons, J.; Boehm, M. H.; Wallis, D. D.; Lühr, H.

The paper reports data received from the Freja satellite during two passes over broad auroral arc systems or inverted-V events above Gillam/Manitoba when special wide-angle CCD cameras were operated at this location in addition to the CANOPUS network. Detailed comparisons of the visible structures with modulations of the primary electron fluxes are performed. Motions of this fine structures are interpreted in terms of high-altitude electric fields shielded from the lower ionosphere. Simultaneous readings of current density, accelerating voltage and energy flux, the latter determined both from particle and auroral brightness measurements, are found to be internally consistent. We calculate from these data the effective resistance encountered by the electric currents and find agreement with the kinetic theory of the mirror impedance, if we allow for substantial variations in density and energy of the source electrons in the magnetosphere.

Serum lipoprotein (a) concentration in patients with nephrotic syndrome and its clinical implication.

PubMed

Yang, X; Wang, H; Zhu, Z; Deng, A

1998-01-01

Serum lipoprotein(a) [Lp(a)] concentration was determined in 42 patients with primary nephrotic syndrome (NS) and the relationships between Lp (a) and plasma lipids, apolipoproteins, serum creatinine (Scr), albumin, urinary proteins (Upro) were also analyzed. The results showed that: (1) serum Lp(a) concentrations in the patients with NS were higher than those in healthy controls; (2) the levels of serum Lp(a) were correlated positively with total cholesterol (TC), low density lipoprotein cholesterol (LDL-C), very low density lipoprotein cholesterol (VLDL-C), apolipoprotein B (Apo-B), Upros (Upro). It is concluded that the NS patients had the potential risk of suffering from coronary artery disease, glomerular sclerosis and thrombosis. The remission of NS may partially decrease the serum Lp(a) levels. Further studies are needed to explore the prevention and treatment of dislipedemia in patients with NS.

Simulation of 90{degrees} ply fatigue crack growth along the width of cross-ply carbon-epoxy coupons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henaff-Gardin, C.; Urwald, E.; Lafarie-Frenot, M.C.

1994-07-01

We study the mechanism of fatigue cracking of the matrix of cross-ply carbon-epoxy laminates. Primary attention is given to the study of the influence of the specimen width on the evolution of damage. On the basis of shear lag analysis, we determine the strain energy release rate in the processes of initiation and growth of transverse fatigue cracks. We also present results of experimental research on the evolution of the edge crack density per ply, the average length of the cracks, and the crack propagation rate under transverse fatigue cracking. It is shown that these characteristics are independent of themore » specimen width. At the same time, as soon as the edge crack density reaches its saturation value, the average crack growth rate becomes constant. All the experimental results are in good agreement with results obtained by using the theoretical model.« less

RADIO ASTROMETRY OF THE CLOSE ACTIVE BINARY HR 5110

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abbuhl, E.; Mutel, R. L.; Lynch, C.

2015-09-20

The close active binary HR 5110 was observed at six epochs over 26 days using a global very long baseline interferometry array at 15.4 GHz. We used phase referencing to determine the position of the radio centroid at each epoch with an uncertainty significantly smaller than the component separation. After correcting for proper motion and parallax, we find that the centroid locations of all six epochs have barycenter separations consistent with an emission source located on the KIV secondary, and not in an interaction region between the stars or on the F primary. We used a homogeneous power-law gyrosynchrotron emissionmore » model to reproduce the observed flux densities and fractional circular polarization. The resulting ranges of mean magnetic field strength and relativistic electron densities are of the order of 10 G and 10{sup 5} cm{sup −3}, respectively, in the source region.« less

Relation between the structural parameters of metallic glasses at the onset crystallization temperatures and threshold values of the effective diffusion coefficients

NASA Astrophysics Data System (ADS)

Tkatch, V. I.; Svyrydova, K. A.; Vasiliev, S. V.; Kovalenko, O. V.

2017-08-01

Using the results of differential scanning calorimetry and X-ray diffractometry, an analysis has been carried out of the initial stages of the eutectic and primary mechanisms of crystallization of a series of metallic glasses based on Fe and Al with the established temperature dependences of the effective diffusion coefficients. Analytical relationships, which relate the volume density of crystallites formed in the glasses at the temperatures of the onset of crystallization with the values of the effective diffusion coefficients at these temperatures have been proposed. It has been established that, in the glasses, the crystallization of which begins at the lower boundary of the threshold values of the effective diffusion coefficients ( 10-20 m2/s), structures are formed with the volume density of crystallites on the order of 1023-1024 m-3 and, at the upper boundary (10-18 m2/s), of the order of 1018 and 1020 m-3 in the glasses that are crystallized via the eutectic and primary mechanisms, respectively. Good agreement between the calculated and experimental estimates indicates that the threshold values of the effective diffusion coefficients are the main factors that determine the structure of glasses at the initial stages of crystallization.

High density of tree-cavities and snags in tropical dry forest of western Mexico raises questions for a latitudinal gradient.

PubMed

Vázquez, Leopoldo; Renton, Katherine

2015-01-01

It has been suggested that a latitudinal gradient exists of a low density of snags and high density of naturally-formed tree-cavities in tropical vs. temperate forests, though few cavities may have characteristics suitable for nesting by birds. We determined snag and cavity density, characteristics, and suitability for birds in a tropical dry forest biome of western Mexico, and evaluated whether our data fits the trend of snag and cavity density typically found in tropical moist and wet forests. We established five 0.25-ha transects to survey and measure tree-cavities and snags in each of three vegetation types of deciduous, semi-deciduous, and mono-dominant Piranhea mexicana forest, comprising a total of 3.75 ha. We found a high density of 77 cavities/ha, with 37 cavities suitable for birds/ha, where density, and characteristics of cavities varied significantly among vegetation types. Lowest abundance of cavities occurred in deciduous forest, and these were in smaller trees, at a lower height, and with a narrower entrance diameter. Only 8.6% of cavities were excavated by woodpeckers, and only 11% of cavities were occupied, mainly by arthropods, though 52% of all cavities were unsuitable for birds. We also found a high density of 56 snags/ha, with greatest density in deciduous forest (70 snags/ha), though these were of significantly smaller diameter, and snags of larger diameter were more likely to contain cavities. The Chamela-Cuixmala tropical dry forest had the highest density of snags recorded for any tropical or temperate forest, and while snag density was significantly correlated with mean snag dbh, neither latitude nor mean dbh predicted snag density in ten forest sites. The high spatial aggregation of snag and cavity resources in tropical dry forest may limit their availability, particularly for large-bodied cavity adopters, and highlights the importance of habitat heterogeneity in providing resources for primary and secondary cavity-nesters.

High Density of Tree-Cavities and Snags in Tropical Dry Forest of Western Mexico Raises Questions for a Latitudinal Gradient

PubMed Central

Vázquez, Leopoldo; Renton, Katherine

2015-01-01

It has been suggested that a latitudinal gradient exists of a low density of snags and high density of naturally-formed tree-cavities in tropical vs. temperate forests, though few cavities may have characteristics suitable for nesting by birds. We determined snag and cavity density, characteristics, and suitability for birds in a tropical dry forest biome of western Mexico, and evaluated whether our data fits the trend of snag and cavity density typically found in tropical moist and wet forests. We established five 0.25-ha transects to survey and measure tree-cavities and snags in each of three vegetation types of deciduous, semi-deciduous, and mono-dominant Piranhea mexicana forest, comprising a total of 3.75 ha. We found a high density of 77 cavities/ha, with 37 cavities suitable for birds/ha, where density, and characteristics of cavities varied significantly among vegetation types. Lowest abundance of cavities occurred in deciduous forest, and these were in smaller trees, at a lower height, and with a narrower entrance diameter. Only 8.6% of cavities were excavated by woodpeckers, and only 11% of cavities were occupied, mainly by arthropods, though 52% of all cavities were unsuitable for birds. We also found a high density of 56 snags/ha, with greatest density in deciduous forest (70 snags/ha), though these were of significantly smaller diameter, and snags of larger diameter were more likely to contain cavities. The Chamela-Cuixmala tropical dry forest had the highest density of snags recorded for any tropical or temperate forest, and while snag density was significantly correlated with mean snag dbh, neither latitude nor mean dbh predicted snag density in ten forest sites. The high spatial aggregation of snag and cavity resources in tropical dry forest may limit their availability, particularly for large-bodied cavity adopters, and highlights the importance of habitat heterogeneity in providing resources for primary and secondary cavity-nesters. PMID:25615612

Modeling of Thermospheric Neutral Density Variations in Response to Geomagnetic Forcing using GRACE Accelerometer Data

NASA Astrophysics Data System (ADS)

Calabia, A.; Matsuo, T.; Jin, S.

2017-12-01

The upper atmospheric expansion refers to an increase in the temperature and density of Earth's thermosphere due to increased geomagnetic and space weather activities, producing anomalous atmospheric drag on LEO spacecraft. Increased drag decelerates satellites, moving their orbit closer to Earth, decreasing the lifespan of satellites, and making satellite orbit determination difficult. In this study, thermospheric neutral density variations due to geomagnetic forcing are investigated from 10 years (2003-2013) of GRACE's accelerometer-based estimates. In order to isolate the variations produced by geomagnetic forcing, 99.8% of the total variability has been modeled and removed through the parameterization of annual, LST, and solar-flux variations included in the primary Empirical Orthogonal Functions. The residual disturbances of neutral density variations have been investigated further in order to unravel their relationship to several geomagnetic indices and space weather activity indicators. Stronger fluctuations have been found in the southern polar cap, following the dipole-tilt angle variations. While the parameterization of the residual disturbances in terms of Dst index results in the best fit to training data, the use of merging electric field as a predictor leads to the best forecasting performance. An important finding is that modeling of neutral density variations in response geomagnetic forcing can be improved by accounting for the latitude-dependent delay. Our data-driven modeling results are further compared to modeling with TIEGCM.

Factors influencing geographic patterns in diversity of forest bird communities of eastern Connecticut, USA

USGS Publications Warehouse

Craig, Robert J.; Klaver, Robert W.

2012-01-01

At regional scales, the most important variables associated with diversity are latitudinally-based temperature and net primary productivity, although diversity is also influenced by habitat. We examined bird species richness, community density and community evenness in forests of eastern Connecticut to determine whether: 1) spatial and seasonal patterns exist in diversity, 2) energy explains the greatest proportion of variation in diversity parameters, 3) variation in habitat explains remaining diversity variance, and 4) seasonal shifts in diversity provide clues about how environmental variables shape communities. We sought to discover if our data supported predictions of the species–energy hypothesis. We used the variable circular plot technique to estimate bird populations and quantified the location, elevation, forest type, vegetation type, canopy cover, moisture regime, understory density and primary production for the study sites. We found that 1) summer richness and population densities are roughly equal in northeastern and southeastern Connecticut, whereas in winter both concentrate toward the coast, 2) variables linked with temperature explained much of the patterns in winter diversity, but energy-related variables showed little relationship to summer diversity, 3) the effect of habitat variables on diversity parameters predominated in summer, although their effect was weak, 4) contrary to theory, evenness increased from summer to winter, and 5) support for predictions of species–energy theory was primarily restricted to winter data. Although energy and habitat played a role in explaining community patterns, they left much of the variance in regional diversity unexplained, suggesting that a large stochastic component to diversity also may exist.

Effect of the environment on the dendritic morphology of the rat auditory cortex

PubMed Central

Bose, Mitali; Muñoz-Llancao, Pablo; Roychowdhury, Swagata; Nichols, Justin A.; Jakkamsetti, Vikram; Porter, Benjamin; Byrapureddy, Rajasekhar; Salgado, Humberto; Kilgard, Michael P.; Aboitiz, Francisco; Dagnino-Subiabre, Alexies; Atzori, Marco

2010-01-01

The present study aimed to identify morphological correlates of environment-induced changes at excitatory synapses of the primary auditory cortex (A1). We used the Golgi-Cox stain technique to compare pyramidal cells dendritic properties of Sprague-Dawley rats exposed to different environmental manipulations. Sholl analysis, dendritic length measures, and spine density counts were used to monitor the effects of sensory deafness and an auditory version of environmental enrichment (EE). We found that deafness decreased apical dendritic length leaving basal dendritic length unchanged, whereas EE selectively increased basal dendritic length without changing apical dendritic length. On the contrary, deafness decreased while EE increased spine density in both basal and apical dendrites of A1 layer 2/3 (LII/III) neurons. To determine whether stress contributed to the observed morphological changes in A1, we studied neural morphology in a restraint-induced model that lacked behaviorally relevant acoustic cues. We found that stress selectively decreased apical dendritic length in the auditory but not in the visual primary cortex. Similar to the acoustic manipulation, stress-induced changes in dendritic length possessed a layer specific pattern displaying LII/III neurons from stressed animals with normal apical dendrites but shorter basal dendrites, while infragranular neurons (layers V and VI) displayed shorter apical dendrites but normal basal dendrites. The same treatment did not induce similar changes in the visual cortex, demonstrating that the auditory cortex is an exquisitely sensitive target of neocortical plasticity, and that prolonged exposure to different acoustic as well as emotional environmental manipulation may produce specific changes in dendritic shape and spine density. PMID:19771593

Evolution of South Atlantic density and chemical stratification across the last deglaciation

PubMed Central

Skinner, Luke C.; Peck, Victoria L.; Kender, Sev; Elderfield, Henry; Waelbroeck, Claire; Hodell, David A.

2016-01-01

Explanations of the glacial–interglacial variations in atmospheric pCO2 invoke a significant role for the deep ocean in the storage of CO2. Deep-ocean density stratification has been proposed as a mechanism to promote the storage of CO2 in the deep ocean during glacial times. A wealth of proxy data supports the presence of a “chemical divide” between intermediate and deep water in the glacial Atlantic Ocean, which indirectly points to an increase in deep-ocean density stratification. However, direct observational evidence of changes in the primary controls of ocean density stratification, i.e., temperature and salinity, remain scarce. Here, we use Mg/Ca-derived seawater temperature and salinity estimates determined from temperature-corrected δ18O measurements on the benthic foraminifer Uvigerina spp. from deep and intermediate water-depth marine sediment cores to reconstruct the changes in density of sub-Antarctic South Atlantic water masses over the last deglaciation (i.e., 22–2 ka before present). We find that a major breakdown in the physical density stratification significantly lags the breakdown of the deep-intermediate chemical divide, as indicated by the chemical tracers of benthic foraminifer δ13C and foraminifer/coral 14C. Our results indicate that chemical destratification likely resulted in the first rise in atmospheric pCO2, whereas the density destratification of the deep South Atlantic lags the second rise in atmospheric pCO2 during the late deglacial period. Our findings emphasize that the physical and chemical destratification of the ocean are not as tightly coupled as generally assumed. PMID:26729858

Evolution of South Atlantic density and chemical stratification across the last deglaciation.

PubMed

Roberts, Jenny; Gottschalk, Julia; Skinner, Luke C; Peck, Victoria L; Kender, Sev; Elderfield, Henry; Waelbroeck, Claire; Vázquez Riveiros, Natalia; Hodell, David A

2016-01-19

Explanations of the glacial-interglacial variations in atmospheric pCO2 invoke a significant role for the deep ocean in the storage of CO2. Deep-ocean density stratification has been proposed as a mechanism to promote the storage of CO2 in the deep ocean during glacial times. A wealth of proxy data supports the presence of a "chemical divide" between intermediate and deep water in the glacial Atlantic Ocean, which indirectly points to an increase in deep-ocean density stratification. However, direct observational evidence of changes in the primary controls of ocean density stratification, i.e., temperature and salinity, remain scarce. Here, we use Mg/Ca-derived seawater temperature and salinity estimates determined from temperature-corrected δ(18)O measurements on the benthic foraminifer Uvigerina spp. from deep and intermediate water-depth marine sediment cores to reconstruct the changes in density of sub-Antarctic South Atlantic water masses over the last deglaciation (i.e., 22-2 ka before present). We find that a major breakdown in the physical density stratification significantly lags the breakdown of the deep-intermediate chemical divide, as indicated by the chemical tracers of benthic foraminifer δ(13)C and foraminifer/coral (14)C. Our results indicate that chemical destratification likely resulted in the first rise in atmospheric pCO2, whereas the density destratification of the deep South Atlantic lags the second rise in atmospheric pCO2 during the late deglacial period. Our findings emphasize that the physical and chemical destratification of the ocean are not as tightly coupled as generally assumed.

Effects of spatial habitat heterogeneity on habitat selection and annual fecundity for a migratory forest songbird

USGS Publications Warehouse

Cornell, K.L.; Donovan, T.M.

2010-01-01

Understanding how spatial habitat patterns influence abundance and dynamics of animal populations is a primary goal in landscape ecology. We used an information-theoretic approach to investigate the association between habitat patterns at multiple spatial scales and demographic patterns for black-throated blue warblers (Dendroica caerulescens) at 20 study sites in west-central Vermont, USA from 2002 to 2005. Sites were characterized by: (1) territory-scale shrub density, (2) patch-scale shrub density occurring within 25 ha of territories, and (3) landscape-scale habitat patterns occurring within 5 km radius extents of territories. We considered multiple population parameters including abundance, age ratios, and annual fecundity. Territory-scale shrub density was most important for determining abundance and age ratios, but landscape-scale habitat structure strongly influenced reproductive output. Sites with higher territory-scale shrub density had higher abundance, and were more likely to be occupied by older, more experienced individuals compared to sites with lower shrub density. However, annual fecundity was higher on sites located in contiguously forested landscapes where shrub density was lower than the fragmented sites. Further, effects of habitat pattern at one spatial scale depended on habitat conditions at different scales. For example, abundance increased with increasing territory-scale shrub density, but this effect was much stronger in fragmented landscapes than in contiguously forested landscapes. These results suggest that habitat pattern at different spatial scales affect demographic parameters in different ways, and that effects of habitat patterns at one spatial scale depends on habitat conditions at other scales. ?? Springer Science+Business Media B.V. 2009.

Correlation Between Bone Density and Instantaneous Torque at Implant Site Preparation: A Validation on Polyurethane Foam Blocks of a Device Assessing Density of Jawbones.

PubMed

Di Stefano, Danilo Alessio; Arosio, Paolo

2016-01-01

Bone density at implant placement sites is one of the key factors affecting implant primary stability, which is a determinant for implant osseointegration and rehabilitation success. Site-specific bone density assessment is, therefore, of paramount importance. Recently, an implant micromotor endowed with an instantaneous torque-measuring system has been introduced. The aim of this study was to assess the reliability of this system. Five blocks with different densities (0.16, 0.26, 0.33, 0.49, and 0.65 g/cm(3)) were used. A single trained operator measured the density of one of them (0.33 g/cm(3)), by means of five different devices (20 measurements/device). The five resulting datasets were analyzed through the analysis of variance (ANOVA) model to investigate interdevice variability. As differences were not significant (P = .41), the five devices were each assigned to a different operator, who collected 20 density measurements for each block, both under irrigation (I) and without irrigation (NI). Measurements were pooled and averaged for each block, and their correlation with the actual block-density values was investigated using linear regression analysis. The possible effect of irrigation on density measurement was additionally assessed. Different devices provided reproducible, homogenous results. No significant interoperator variability was observed. Within the physiologic range of densities (> 0.30 g/cm(3)), the linear regression analysis showed a significant linear correlation between the mean torque measurements and the actual bone densities under both drilling conditions (r = 0.990 [I], r = 0.999 [NI]). Calibration lines were drawn under both conditions. Values collected under irrigation were lower than those collected without irrigation at all densities. The NI/I mean torque ratio was shown to decrease linearly with density (r = 0.998). The mean error introduced by the device-operator system was less than 10% in the range of normal jawbone density. Measurements performed with the device were linearly correlated with the blocks' bone densities. The results validate the device as an objective intraoperative tool for bone-density assessment that may contribute to proper jawbone-density evaluation and implant-insertion planning.

The role of OH…O and CH…O hydrogen bonds and H…H interactions in ethanol/methanol-water heterohexamers.

PubMed

Mejía, Sol M; Espinal, Juan F; Mills, Matthew J L; Mondragón, Fanor

2016-08-01

Bioethanol is one of the world's most extensively produced biofuels. However, it is difficult to purify due to the formation of the ethanol-water azeotrope. Knowledge of the azeotrope structure at the molecular level can help to improve existing purification methods. In order to achieve a better understanding of this azeotrope structure, the characterization of (ethanol)5-water heterohexamers was carried out by analyzing the results of electronic structure calculations performed at the B3LYP/6-31+G(d) level. Hexamerization energies were found to range between -36.8 and -25.8 kcal/mol. Topological analysis of the electron density confirmed the existence of primary (OH…O) hydrogen bonds (HBs), secondary (CH…O) HBs, and H…H interactions in these clusters. Comparison with three different solvated alcohol systems featuring the same types of atom-atom interactions permitted the following order of stability to be determined: (methanol)5-water > (methanol)6 > (ethanol)5-water > (ethanol)6. These findings, together with accompanying geometric and spectroscopic analyses, show that similar cooperative effects exist among the primary HBs for structures with the same arrangement of primary HBs, regardless of the nature of the molecules involved. This result provides an indication that the molecular ratio can be considered to determine the unusual behavior of the ethanol-water system. The investigation also highlights the presence of several types of weak interaction in addition to primary HBs. Graphical Abstract Water-ethanol clusters exhibit a variety of interaction types between their atoms, such as primary OH...O (blue), secondary CH...O (green) and H...H (yellow) interactions as revealed by Quantum Chemical Topology.

The relation between invertebrate drift and two primary controls, discharge and benthic densities, in a large regulated river

USGS Publications Warehouse

Kennedy, Theodore A.; Yackulic, Charles B.; Cross, Wyatt F.; Grams, Paul E.; Yard, Michael D.; Copp, Adam J.

2014-01-01

1. Invertebrate drift is a fundamental process in streams and rivers. Studies from laboratory experiments and small streams have identified numerous extrinsic (e.g. discharge, light intensity, water quality) and intrinsic factors (invertebrate life stage, benthic density, behaviour) that govern invertebrate drift concentrations (# m−3), but the factors that govern invertebrate drift in larger rivers remain poorly understood. For example, while large increases or decreases in discharge can lead to large increases in invertebrate drift, the role of smaller, incremental changes in discharge is poorly described. In addition, while we might expect invertebrate drift concentrations to be proportional to benthic densities (# m−2), the benthic–drift relation has not been rigorously evaluated. 2. Here, we develop a framework for modelling invertebrate drift that is derived from sediment transport studies. We use this framework to guide the analysis of high-resolution data sets of benthic density and drift concentration for four important invertebrate taxa from the Colorado River downstream of Glen Canyon Dam (mean daily discharge 325 m3 s−1) that were collected over 18 months and include multiple observations within days. Ramping of regulated flows on this river segment provides an experimental treatment that is repeated daily and allowed us to describe the functional relations between invertebrate drift and two primary controls, discharge and benthic densities. 3. Twofold daily variation in discharge resulted in a >10-fold increase in drift concentrations of benthic invertebrates associated with pools and detritus (i.e. Gammarus lacustris and Potamopyrgus antipodarum). In contrast, drift concentrations of sessile blackfly larvae (Simuliium arcticum), which are associated with high-velocity cobble microhabitats, decreased by over 80% as discharge doubled. Drift concentrations of Chironomidae increased proportional to discharge. 4. Drift of all four taxa was positively related to benthic density. Drift concentrations of Gammarus, Potamopyrgus and Chironomidae were proportional to benthic density. Drift concentrations of Simulium were positively related to benthic density, but the benthic–drift relation was less than proportional (i.e. a doubling of benthic density only led to a 40% increase in drift concentrations). 5. Our study demonstrates that invertebrate drift concentrations in the Colorado River are jointly controlled by discharge and benthic densities, but these controls operate at different timescales. Twofold daily variation in discharge associated with hydropeaking was the primary control on within-day variation in invertebrate drift concentrations. In contrast, benthic density, which varied 10- to 1000-fold among sampling dates, depending on the taxa, was the primary control on invertebrate drift concentrations over longer timescales (weeks to months).

Cosmic Ray Positrons from Pulsars

NASA Technical Reports Server (NTRS)

Harding, Alice K.

2010-01-01

Pulsars are potential Galactic sources of positrons through pair cascades in their magnetospheres. There are, however, many uncertainties in establishing their contribution to the local primary positron flux. Among these are the local density of pulsars, the cascade pair multiplicities that determine the injection rate of positrons from the pulsar, the acceleration of the injected particles by the pulsar wind termination shock, their rate of escape from the pulsar wind nebula, and their propagation through the interstellar medium. I will discuss these issues in the context of what we are learning from the new Fermi pulsar detections and discoveries.

Exercise effects on bone mineral density in older men: a systematic review with special emphasis on study interventions.

PubMed

Kemmler, W; Shojaa, M; Kohl, M; von Stengel, S

2018-04-05

This systematic review detected only limited positive effects of exercise on bone mineral density in older men. Further, based on the present literature, we were unable to suggest dedicated exercise prescriptions for this male cohort that might differ from recommendations based on studies with postmenopausal women. The primary aim of this systematic review was to determine the effect of exercise on bone mineral density (BMD) in healthy older men. A systematic review of the literature according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses statement included only randomized or non-randomized controlled trials of exercise training ≥ 6 months with study groups of ≥ eight healthy men aged 50 years or older, not using bone-relevant pharmacological therapy, that determined BMD by dual-energy X-ray absorptiometry. We searched PubMed, Scopus, Web of Science, Cochrane, Science Direct, and Eric up to November 2016. Risk of bias was assessed using the PEDro scale. We identified eight trials with 789 participants (PEDro-score, mean value 6 of 10) which satisfied our eligibility criteria. Studies vary considerably with respect to type and composition of exercise. Study interventions of six trials were considered to be appropriate for successfully addressing BMD in this cohort. Between-group differences were not or not consistently reported by three studies. Three studies reported significant exercise effects on BMD for proximal femur; one of them determined significant differences between the exercise groups. None of the exercise trials determined significant BMD effects at the lumbar spine. Based on the present studies, there is only limited evidence for a favorable effect of exercise on BMD in men. More well-designed and sophisticated studies on BMD in healthy older men have to address this topic. Further, there is a need to define intervention quality standards and implement a universal scoring system that allows this pivotal determinant to be addressed much more intensively.

Reader variability in breast density estimation from full-field digital mammograms: the effect of image postprocessing on relative and absolute measures.

PubMed

Keller, Brad M; Nathan, Diane L; Gavenonis, Sara C; Chen, Jinbo; Conant, Emily F; Kontos, Despina

2013-05-01

Mammographic breast density, a strong risk factor for breast cancer, may be measured as either a relative percentage of dense (ie, radiopaque) breast tissue or as an absolute area from either raw (ie, "for processing") or vendor postprocessed (ie, "for presentation") digital mammograms. Given the increasing interest in the incorporation of mammographic density in breast cancer risk assessment, the purpose of this study is to determine the inherent reader variability in breast density assessment from raw and vendor-processed digital mammograms, because inconsistent estimates could to lead to misclassification of an individual woman's risk for breast cancer. Bilateral, mediolateral-oblique view, raw, and processed digital mammograms of 81 women were retrospectively collected for this study (N = 324 images). Mammographic percent density and absolute dense tissue area estimates for each image were obtained from two radiologists using a validated, interactive software tool. The variability of interreader agreement was not found to be affected by the image presentation style (ie, raw or processed, F-test: P > .5). Interreader estimates of relative and absolute breast density are strongly correlated (Pearson r > 0.84, P < .001) but systematically different (t-test, P < .001) between the two readers. Our results show that mammographic density may be assessed with equal reliability from either raw or vendor postprocessed images. Furthermore, our results suggest that the primary source of density variability comes from the subjectivity of the individual reader in assessing the absolute amount of dense tissue present in the breast, indicating the need to use standardized tools to mitigate this effect. Copyright © 2013 AUR. Published by Elsevier Inc. All rights reserved.

Response of tree growth and species coexistence to density and species evenness in a young forest plantation with two competing species.

PubMed

Collet, Catherine; Ningre, François; Barbeito, Ignacio; Arnaud, Anthony; Piboule, Alexandre

2014-03-01

There is considerable evidence for the presence of positive species diversity-productivity relationships in plant populations, but the population parameters determining the type and strength of the relationship are poorly defined. Relationships between species evenness and tree survival or species coexistence are not well established. The objective of this study was to quantify the joint effects of density and species evenness on tree productivity and species coexistence. A 12-year-old experimental tree plantation mixing two species according to a double gradient of density and species proportion was used. A neighbourhood approach was employed and descriptors of local competition were used to model individual tree growth. Fagus sylvatica and Acer pseudoplatanus were used as model species, as they can be considered as ecologically equivalent in their young stages. Density and tree size were primary factors determining individual growth and stand productivity. Species identity had a significant, but less pronounced, role. Stand productivity was highest when species evenness was close to 1 and slightly lower in uneven mixtures. The reduction in stand productivity when species evenness decreased was of similar magnitude irrespective of which species became dominant, indicating symmetric effects for the two species. When examining individual tree growth in response to species proportion for each species separately, it was observed for both species that individual trees exhibited greater growth in uneven mixtures in which the other species was more frequent. The results suggest that mixtures of these two functionally similar species have the highest production at maximum evenness, indicating a complementary effect between them. The presence of a mixture combines both stabilizing mechanisms (individuals from both species show higher growth when surrounded by individuals from the other species) and equalizing mechanisms (the two species have very similar growth curves) that, in turn, determine the species' relative dominance. These processes should act to ensure the long-term coexistence of species.

Response of tree growth and species coexistence to density and species evenness in a young forest plantation with two competing species

PubMed Central

Collet, Catherine; Ningre, François; Barbeito, Ignacio; Arnaud, Anthony; Piboule, Alexandre

2014-01-01

Background and Aims There is considerable evidence for the presence of positive species diversity–productivity relationships in plant populations, but the population parameters determining the type and strength of the relationship are poorly defined. Relationships between species evenness and tree survival or species coexistence are not well established. The objective of this study was to quantify the joint effects of density and species evenness on tree productivity and species coexistence. Methods A 12-year-old experimental tree plantation mixing two species according to a double gradient of density and species proportion was used. A neighbourhood approach was employed and descriptors of local competition were used to model individual tree growth. Fagus sylvatica and Acer pseudoplatanus were used as model species, as they can be considered as ecologically equivalent in their young stages. Key Results Density and tree size were primary factors determining individual growth and stand productivity. Species identity had a significant, but less pronounced, role. Stand productivity was highest when species evenness was close to 1 and slightly lower in uneven mixtures. The reduction in stand productivity when species evenness decreased was of similar magnitude irrespective of which species became dominant, indicating symmetric effects for the two species. When examining individual tree growth in response to species proportion for each species separately, it was observed for both species that individual trees exhibited greater growth in uneven mixtures in which the other species was more frequent. Conclusions The results suggest that mixtures of these two functionally similar species have the highest production at maximum evenness, indicating a complementary effect between them. The presence of a mixture combines both stabilizing mechanisms (individuals from both species show higher growth when surrounded by individuals from the other species) and equalizing mechanisms (the two species have very similar growth curves) that, in turn, determine the species' relative dominance. These processes should act to ensure the long-term coexistence of species. PMID:24323248

Untangling ciliary access and enrichment of two rhodopsin-like receptors using quantitative fluorescence microscopy reveals cell-specific sorting pathways

PubMed Central

Geneva, Ivayla I.; Tan, Han Yen; Calvert, Peter D.

2017-01-01

Resolution limitations of optical systems are major obstacles for determining whether proteins are enriched within cell compartments. Here we use an approach to determine the degree of membrane protein ciliary enrichment that quantitatively accounts for the differences in sampling of the ciliary and apical membranes inherent to confocal microscopes. Theory shows that cilia will appear more than threefold brighter than the surrounding apical membrane when the densities of fluorescently labeled proteins are the same, thus providing a benchmark for ciliary enrichment. Using this benchmark, we examined the ciliary enrichment signals of two G protein–coupled receptors (GPCRs)—the somatostatin receptor 3 and rhodopsin. Remarkably, we found that the C-terminal VxPx motif, required for efficient enrichment of rhodopsin within rod photoreceptor sensory cilia, inhibited enrichment of the somatostatin receptor in primary cilia. Similarly, VxPx inhibited primary cilium enrichment of a chimera of rhodopsin and somatostatin receptor 3, where the dual Ax(S/A)xQ ciliary targeting motifs within the third intracellular loop of the somatostatin receptor replaced the third intracellular loop of rhodopsin. Rhodopsin was depleted from primary cilia but gained access, without being enriched, with the dual Ax(S/A)xQ motifs. Ciliary enrichment of these GPCRs thus operates via distinct mechanisms in different cells. PMID:27974638

An investigation of siderophore production by oceanic Synechococcus

NASA Astrophysics Data System (ADS)

Wisniewski, R. J.; Webb, E. A.; Moffett, J. W.

2003-04-01

Cyanobacteria are significant contributors to global primary production. They can be found in warm high-nutrient, low-chlorophyll regions where low concentrations of iron are thought to limit primary productivity. Determining how these organisms obtain iron is critical to understanding the biogeochemical cycle of iron and its role as a determinant of marine primary production. Siderophore production has been observed in halotolerant freshwater cyanobacteria (see C.G. Trick and co-authors) and marine heterotrophic bacteria (see A. Butler, M.G. Haygood and co-authors), but to date, siderophore production in truly marine cyanobacteria has not been demonstrated. We examined the response of two marine Synechococcus species (WH7803 and WH8102) to iron stress. Axenic cultures of both Synechococcus species were grown under iron-stressed and iron-replete conditions. The supernatants of these cultures were examined using competitive ligand exchange-cathodic stripping voltammetry (CLE-CSV), a sensitive method of quantitative ligand detection. Observing ligand accumulation in culture is an analytical challenge due to the low cell densities and reduced growth rates of iron stressed marine cyanobacteria. Preliminary results suggest the presence of an iron-binding ligand in the iron-stressed cultures which was not present under iron-replete conditions. The amount of ligand produced by Synechococcus was approximately 1 × 10-18 mol/cell, comparable with the amount produced by marine heterotrophic bacteria (K. Barbeau, pers. comm.).

Edge Stabilized Ribbon (ESR); Stress, Dislocation Density and Electronic Performance

NASA Technical Reports Server (NTRS)

Sachs, E. M.

1984-01-01

The edge stabilized ribbon (ESR) silicon ribbon was grown in widths of 1, 2.2 and 4.0 inches at speeds ranging from .6 to 7 in/min, which result in ribbon thicknesses of 5 to 400 microns. One of the primary problems remaining in ESR growth is that of thermally induced mechanical stresses. This problem is manifested as ribbon with a high degree of residual stress or as ribbon with buckled ribbon. Thermal stresses result in a high dislocation density in the grown material, resulting in compromised electronic performance. Improvements in ribbon flatness were accomplished by modification of the ribbon cooling profile. Ribbon flatness and other experimental observations of ESR ribbon are discussed. Laser scanner measurements show a good correlation between diffusion length and dislocation density which indicates that the high dislocation densities are the primary cause of the poor current performance of ESR materials. Dislocation densities were reduced and improved electronic performance resulted. Laser scanner data on new and old material are presented.

Development of a Long-Range Underwater Vehicle

DTIC Science & Technology

2015-09-30

contained lithium primary batteries . Based on reaction energy and reactant mass, oxidation of lithium is a particularly high energy density option. Each...LiOH E ~ 3.45 V Hydrogen evolution in seawater 2Li + 2H2O = 2 LiOH + H2 E ~ 2.60 V PolyPlus Battery Company has developed a lithium -seawater...PolyPlus achieves energy densities near 4.7 MJ/kg, four times that available from the primary lithium batteries used in gliders today. The seawater cells

F-18-Fluorodeoxyglucose Positron Emission Tomography/Computed Tomography Appearance of Extramedullary Hematopoesis in a Case of Primary Myelofibrosis

PubMed Central

Mukherjee, Anirban; Bal, Chandrasekhar; Tripathi, Madhavi; Das, Chandan Jyoti; Shamim, Shamim Ahmed

2017-01-01

A 44-year-old female with known primary myelofibrosis presented with shortness of breath. High Resolution Computed Tomography thorax revealed large heterogeneously enhancing extraparenchymal soft tissue density mass involving bilateral lung fields. F-18-fluorodeoxyglucose (FDG) positron emission tomography/computed tomography revealed mildly FDG avid soft tissue density mass with specks of calcification involving bilateral lung fields, liver, and spleen. Subsequent histopathologic evaluation from the right lung mass was suggestive of extramedullary hematopoesis. PMID:28533647

Engine-induced structural-borne noise in a general aviation aircraft

NASA Technical Reports Server (NTRS)

Unruh, J. F.; Scheidt, D. C.; Pomerening, D. J.

1979-01-01

Structural borne interior noise in a single engine general aviation aircraft was studied to determine the importance of engine induced structural borne noise and to determine the necessary modeling requirements for the prediction of structural borne interior noise. Engine attached/detached ground test data show that engine induced structural borne noise is a primary interior noise source for the single engine test aircraft, cabin noise is highly influenced by responses at the propeller tone, and cabin acoustic resonances can influence overall noise levels. Results from structural and acoustic finite element coupled models of the test aircraft show that wall flexibility has a strong influence on fundamental cabin acoustic resonances, the lightweight fuselage structure has a high modal density, and finite element analysis procedures are appropriate for the prediction of structural borne noise.

Procedure for Uranium-Molybdenum Density Measurements and Porosity Determination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prabhakaran, Ramprashad; Devaraj, Arun; Joshi, Vineet V.

2016-08-13

The purpose of this document is to provide guidelines for preparing uranium-molybdenum (U-Mo) specimens, performing density measurements, and computing sample porosity. Typical specimens (solids) will be sheared to small rectangular foils, disks, or pieces of metal. A mass balance, solid density determination kit, and a liquid of known density will be used to determine the density of U-Mo specimens using the Archimedes principle. A standard test weight of known density would be used to verify proper operation of the system. By measuring the density of a U-Mo sample, it is possible to determine its porosity.

Energy Density, Energy Intake, and Body Weight Regulation in Adults12345

PubMed Central

Karl, J. Philip; Roberts, Susan B.

2014-01-01

The role of dietary energy density (ED) in the regulation of energy intake (EI) is controversial. Methodologically, there is also debate about whether beverages should be included in dietary ED calculations. To address these issues, studies examining the effects of ED on EI or body weight in nonelderly adults were reviewed. Different approaches to calculating dietary ED do not appear to alter the direction of reported relations between ED and body weight. Evidence that lowering dietary ED reduces EI in short-term studies is convincing, but there are currently insufficient data to determine long-term effectiveness for weight loss. The review also identified key barriers to progress in understanding the role of ED in energy regulation, in particular the absence of a standard definition of ED, and the lack of data from multiple long-term clinical trials examining the effectiveness of low-ED diet recommendations for preventing both primary weight gain and weight regain in nonobese individuals. Long-term clinical trials designed to examine the impact of dietary ED on energy regulation, and including multiple ED calculation methods within the same study, are still needed to determine the importance of ED in the regulation of EI and body weight. PMID:25398750

The First Estimates of Marbled Cat Pardofelis marmorata Population Density from Bornean Primary and Selectively Logged Forest.

PubMed

Hearn, Andrew J; Ross, Joanna; Bernard, Henry; Bakar, Soffian Abu; Hunter, Luke T B; Macdonald, David W

2016-01-01

The marbled cat Pardofelis marmorata is a poorly known wild cat that has a broad distribution across much of the Indomalayan ecorealm. This felid is thought to exist at low population densities throughout its range, yet no estimates of its abundance exist, hampering assessment of its conservation status. To investigate the distribution and abundance of marbled cats we conducted intensive, felid-focused camera trap surveys of eight forest areas and two oil palm plantations in Sabah, Malaysian Borneo. Study sites were broadly representative of the range of habitat types and the gradient of anthropogenic disturbance and fragmentation present in contemporary Sabah. We recorded marbled cats from all forest study areas apart from a small, relatively isolated forest patch, although photographic detection frequency varied greatly between areas. No marbled cats were recorded within the plantations, but a single individual was recorded walking along the forest/plantation boundary. We collected sufficient numbers of marbled cat photographic captures at three study areas to permit density estimation based on spatially explicit capture-recapture analyses. Estimates of population density from the primary, lowland Danum Valley Conservation Area and primary upland, Tawau Hills Park, were 19.57 (SD: 8.36) and 7.10 (SD: 1.90) individuals per 100 km2, respectively, and the selectively logged, lowland Tabin Wildlife Reserve yielded an estimated density of 10.45 (SD: 3.38) individuals per 100 km2. The low detection frequencies recorded in our other survey sites and from published studies elsewhere in its range, and the absence of previous density estimates for this felid suggest that our density estimates may be from the higher end of their abundance spectrum. We provide recommendations for future marbled cat survey approaches.

The First Estimates of Marbled Cat Pardofelis marmorata Population Density from Bornean Primary and Selectively Logged Forest

PubMed Central

Hearn, Andrew J.; Ross, Joanna; Bernard, Henry; Bakar, Soffian Abu; Hunter, Luke T. B.; Macdonald, David W.

2016-01-01

The marbled cat Pardofelis marmorata is a poorly known wild cat that has a broad distribution across much of the Indomalayan ecorealm. This felid is thought to exist at low population densities throughout its range, yet no estimates of its abundance exist, hampering assessment of its conservation status. To investigate the distribution and abundance of marbled cats we conducted intensive, felid-focused camera trap surveys of eight forest areas and two oil palm plantations in Sabah, Malaysian Borneo. Study sites were broadly representative of the range of habitat types and the gradient of anthropogenic disturbance and fragmentation present in contemporary Sabah. We recorded marbled cats from all forest study areas apart from a small, relatively isolated forest patch, although photographic detection frequency varied greatly between areas. No marbled cats were recorded within the plantations, but a single individual was recorded walking along the forest/plantation boundary. We collected sufficient numbers of marbled cat photographic captures at three study areas to permit density estimation based on spatially explicit capture-recapture analyses. Estimates of population density from the primary, lowland Danum Valley Conservation Area and primary upland, Tawau Hills Park, were 19.57 (SD: 8.36) and 7.10 (SD: 1.90) individuals per 100 km2, respectively, and the selectively logged, lowland Tabin Wildlife Reserve yielded an estimated density of 10.45 (SD: 3.38) individuals per 100 km2. The low detection frequencies recorded in our other survey sites and from published studies elsewhere in its range, and the absence of previous density estimates for this felid suggest that our density estimates may be from the higher end of their abundance spectrum. We provide recommendations for future marbled cat survey approaches. PMID:27007219

Reduced Glutamate Decarboxylase 65 Protein Within Primary Auditory Cortex Inhibitory Boutons in Schizophrenia

PubMed Central

Moyer, Caitlin E.; Delevich, Kristen M.; Fish, Kenneth N.; Asafu-Adjei, Josephine K.; Sampson, Allan R.; Dorph-Petersen, Karl-Anton; Lewis, David A.; Sweet, Robert A.

2012-01-01

Background Schizophrenia is associated with perceptual and physiological auditory processing impairments that may result from primary auditory cortex excitatory and inhibitory circuit pathology. High-frequency oscillations are important for auditory function and are often reported to be disrupted in schizophrenia. These oscillations may, in part, depend on upregulation of gamma-aminobutyric acid synthesis by glutamate decarboxylase 65 (GAD65) in response to high interneuron firing rates. It is not known whether levels of GAD65 protein or GAD65-expressing boutons are altered in schizophrenia. Methods We studied two cohorts of subjects with schizophrenia and matched control subjects, comprising 27 pairs of subjects. Relative fluorescence intensity, density, volume, and number of GAD65-immunoreactive boutons in primary auditory cortex were measured using quantitative confocal microscopy and stereologic sampling methods. Bouton fluorescence intensities were used to compare the relative expression of GAD65 protein within boutons between diagnostic groups. Additionally, we assessed the correlation between previously measured dendritic spine densities and GAD65-immunoreactive bouton fluorescence intensities. Results GAD65-immunoreactive bouton fluorescence intensity was reduced by 40% in subjects with schizophrenia and was correlated with previously measured reduced spine density. The reduction was greater in subjects who were not living independently at time of death. In contrast, GAD65-immunoreactive bouton density and number were not altered in deep layer 3 of primary auditory cortex of subjects with schizophrenia. Conclusions Decreased expression of GAD65 protein within inhibitory boutons could contribute to auditory impairments in schizophrenia. The correlated reductions in dendritic spines and GAD65 protein suggest a relationship between inhibitory and excitatory synapse pathology in primary auditory cortex. PMID:22624794

Association between serum cholesterol and eating behaviours during early childhood: a cross-sectional study.

PubMed

Persaud, Navindra; Maguire, Jonathon L; Lebovic, Gerald; Carsley, Sarah; Khovratovich, Marina; Randall Simpson, Janis A; McCrindle, Brian W; Parkin, Patricia C; Birken, Catherine

2013-08-06

Modifiable behaviours during early childhood may provide opportunities to prevent disease processes before adverse outcomes occur. Our objective was to determine whether young children's eating behaviours were associated with increased risk of cardiovascular disease in later life. In this cross-sectional study involving children aged 3-5 years recruited from 7 primary care practices in Toronto, Ontario, we assessed the relation between eating behaviours as assessed by the NutriSTEP (Nutritional Screening Tool for Every Preschooler) questionnaire (completed by parents) and serum levels of non-high-density lipoprotein (HDL) cholesterol, a surrogate marker of cardiovascular risk. We also assessed the relation between dietary intake and serum non-HDL cholesterol, and between eating behaviours and other laboratory indices of cardiovascular risk (low-density lipoprotein [LDL] cholesterol, apolipoprotein B, HDL cholesterol and apoliprotein A1). A total of 1856 children were recruited from primary care practices in Toronto. Of these children, we included 1076 in our study for whom complete data and blood samples were available for analysis. The eating behaviours subscore of the NutriSTEP tool was significantly associated with serum non-HDL cholesterol (p = 0.03); for each unit increase in the eating behaviours subscore suggesting greater nutritional risk, we saw an increase of 0.02 mmol/L (95% confidence interval [CI] 0.002 to 0.05) in serum non-HDL cholesterol. The eating behaviours subscore was also associated with LDL cholesterol and apolipoprotein B, but not with HDL cholesterol or apolipoprotein A1. The dietary intake subscore was not associated with non-HDL cholesterol. Eating behaviours in preschool-aged children are important potentially modifiable determinants of cardiovascular risk and should be a focus for future studies of screening and behavioural interventions.

Density Measurement System for Weights of 1 kg to 20 kg Using Hydrostatic Weighing

NASA Astrophysics Data System (ADS)

Lee, Yong Jae; Lee, Woo Gab; Abdurahman, Mohammed; Kim, Kwang Pyo

This paper presents a density measurement system to determine density of weights from 1 kg to 20 kg using hydrostatic weighing. The system works based on Archimedes principle. The density of reference liquid is determined using this setup while determining the density of the test weight. Density sphere is used as standard density ball to determine density of the reference liquid. A new immersion pan is designed for dual purpose to carry the density sphere and the cylindrical test weight for weighing in liquid. Main parts of the setup are an electronic balance, a thermostat controlled liquid bath, reference weights designed for bottom weighing, dual purpose immersion pans and stepping motors to load and unload in weighing process. The results of density measurement will be evaluated as uncertainties for weights of 1 kg to 20 kg.

Predation on exotic zebra mussels by native fishes: Effects on predator and prey

USGS Publications Warehouse

Magoulick, D.D.; Lewis, L.C.

2002-01-01

1. Exotic zebra mussels, Dreissena polymorpha, occur in southern U.S. waterways in high densities, but little is known about the interaction between native fish predators and zebra mussels. Previous studies have suggested that exotic zebra mussels are low profitability prey items and native vertebrate predators are unlikely to reduce zebra mussel densities. We tested these hypotheses by observing prey use of fishes, determining energy content of primary prey species of fishes, and conducting predator exclusion experiments in Lake Dardanelle, Arkansas. 2. Zebra mussels were the primary prey eaten by 52.9% of blue catfish, Ictalurus furcatus; 48.2% of freshwater drum, Aplodinotus grunniens; and 100% of adult redear sunfish, Lepomis microlophus. Blue catfish showed distinct seasonal prey shifts, feeding on zebra mussels in summer and shad, Dorosoma spp., during winter. Energy content (joules g-1) of blue catfish prey (threadfin shad, Dorosoma petenense; gizzard shad, D. cepedianum; zebra mussels; and asiatic clams, Corbicula fluminea) showed a significant species by season interaction, but shad were always significantly greater in energy content than bivalves examined as either ash-free dry mass or whole organism dry mass. Fish predators significantly reduced densities of large zebra mussels (>5 mm length) colonising clay tiles in the summers of 1997 and 1998, but predation effects on small zebra mussels (???5 mm length) were less clear. 3. Freshwater drum and redear sunfish process bivalve prey by crushing shells and obtain low amounts of higher-energy food (only the flesh), whereas blue catfish lack a shell-crushing apparatus and ingest large amounts of low-energy food per unit time (bivalves with their shells). Blue catfish appeared to select the abundant zebra mussel over the more energetically rich shad during summer, then shifted to shad during winter when shad experienced temperature-dependent stress and mortality. Native fish predators can suppress adult zebra mussel colonisation, but are ultimately unlikely to limit population density because of zebra mussel reproductive potential.

Natural variation in stomatal abundance of Arabidopsis thaliana includes cryptic diversity for different developmental processes

PubMed Central

Delgado, Dolores; Alonso-Blanco, Carlos; Fenoll, Carmen; Mena, Montaña

2011-01-01

Background and Aims Current understanding of stomatal development in Arabidopsis thaliana is based on mutations producing aberrant, often lethal phenotypes. The aim was to discover if naturally occurring viable phenotypes would be useful for studying stomatal development in a species that enables further molecular analysis. Methods Natural variation in stomatal abundance of A. thaliana was explored in two collections comprising 62 wild accessions by surveying adaxial epidermal cell-type proportion (stomatal index) and density (stomatal and pavement cell density) traits in cotyledons and first leaves. Organ size variation was studied in a subset of accessions. For all traits, maternal effects derived from different laboratory environments were evaluated. In four selected accessions, distinct stomatal initiation processes were quantitatively analysed. Key Results and Conclusions Substantial genetic variation was found for all six stomatal abundance-related traits, which were weakly or not affected by laboratory maternal environments. Correlation analyses revealed overall relationships among all traits. Within each organ, stomatal density highly correlated with the other traits, suggesting common genetic bases. Each trait correlated between organs, supporting supra-organ control of stomatal abundance. Clustering analyses identified accessions with uncommon phenotypic patterns, suggesting differences among genetic programmes controlling the various traits. Variation was also found in organ size, which negatively correlated with cell densities in both organs and with stomatal index in the cotyledon. Relative proportions of primary and satellite lineages varied among the accessions analysed, indicating that distinct developmental components contribute to natural diversity in stomatal abundance. Accessions with similar stomatal indices showed different lineage class ratios, revealing hidden developmental phenotypes and showing that genetic determinants of primary and satellite lineage initiation combine in several ways. This first systematic, comprehensive natural variation survey for stomatal abundance in A. thaliana reveals cryptic developmental genetic variation, and provides relevant relationships amongst stomatal traits and extreme or uncommon accessions as resources for the genetic dissection of stomatal development. PMID:21447490

Effects of a high-gradient magnetic field on the migratory behavior of primary crystal silicon in hypereutectic Al–Si alloy

PubMed Central

Jin, Fangwei; Ren, Zhongming; Ren, Weili; Deng, Kang; Zhong, Yunbo; Yu, Jianbo

2008-01-01

The migration of primary Si grains during the solidification of Al–18 wt%Si alloy under a high-gradient magnetic field has been investigated experimentally. It was found that under a gradient magnetic field, the primary Si grains migrated toward one end of the specimen, forming a Si-rich layer, and the thickness of the Si-rich layer increased with increasing magnetic flux density. No movement of Si grains was apparent under a magnetic field below 2.3 T. For magnetic fields above 6.6 T, however, the thickness of the Si-rich layer was almost constant. It was shown that the static field also played a role in impeding the movement of the grains. The primary Si grains were refined in the Si layer, even though the primary silicon grains were very dense. The effect of the magnetic flux density on the migratory behavior is discussed. PMID:27877953

An assessment of the mechanical stability of wells offshore Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowrey, J.P.; Ottesen, S.

In 1991 lost time due to stuck pipe related drilling problems accounted for approximately 18% of total drilling time in Mobil Producing Nigeria Ultd.`s (MPN) offshore operations. The primary cause of stuck pipe was identified as mechanical wellbore instability. This paper presents an assessment of the mechanical stability of MPN`s wells offshore Nigeria. The objectives of the study were to: (1) determine the magnitude of the in-situ principal stresses and material properties of the troublesome Intra-Biafra and Qua Iboe shale sequences; (2) quantify the drilling fluid densities required to drill mechanically stable wells through these formations; (3) review and recommendmore » well planning and operational parameters which aid in minimizing wellbore stability-related drilling problems. The well-bore stability assessment was carried out with the aid of a 3-dimensional wellbore stability model using field derived data from the study area to corroborate the results. The collection and analysis of drilling data (borehole geometry and density logs, pore pressure, leak-off tests, local geology and other relevant well records) to determine the magnitude of the in-situ principal stresses, together with compressive strength tests on formation cores are discussed. Minimum safe drilling fluid densities to promote wellbore stability as a function of well geometry and depth are presented for the most troublesome shales drilled in the study area. Implementation of the results reduced wellbore stability related problems and associated trouble time to less than 5% in 1992.« less

Distant Secondary Craters and Age Constraints on Young Martian Terrains

NASA Technical Reports Server (NTRS)

McEwen, A.; Preblich, B.; Turtle, E.; Studer, D.; Artemieva, N.; Golombek, M.; Hurst, M.; Kirk, R.; Burr, D.

2005-01-01

Are small (less than approx. 1 km diameter) craters on Mars and the Moon dominated by primary impacts, by secondary impacts of much larger primary craters, or are both primaries and secondaries significant? This question is critical to age constraints for young terrains and for older terrains covering small areas, where only small craters are superimposed on the unit. If the martian rayed crater Zunil is representative of large impact events on Mars, then the density of secondaries should exceed the density of primaries at diameters a factor of 1000 smaller than that of the largest contributing primary crater. On the basis of morphology and depth/diameter measurements, most small craters on Mars could be secondaries. Two additional observations (discussed below) suggest that the production functions of Hartmann and Neukum predict too many primary craters smaller than a few hundred meters in diameter. Fewer small, high-velocity impacts may explain why there appears to be little impact regolith over Amazonian terrains. Martian terrains dated by small craters could be older than reported in recent publications.

Muographic mapping of the subsurface density structures in Miura, Boso and Izu peninsulas, Japan

NASA Astrophysics Data System (ADS)

Tanaka, Hiroyuki K. M.

2015-02-01

While the benefits of determining the bulk density distribution of a landmass are evident, established experimental techniques reliant on gravity measurements cannot uniquely determine the underground density distribution. We address this problem by taking advantage of traffic tunnels densely distributed throughout the country. Cosmic ray muon flux is measured in the tunnels to determine the average density of each rock overburden. After analyzing the data collected from 146 observation points in Miura, South-Boso and South-Izu Peninsula, Japan as an example, we mapped out the shallow density distribution of an area of 1340 km2. We find a good agreement between muographically determined density distribution and geologic features as described in existing geological studies. The average shallow density distribution below each peninsula was determined with a great accuracy (less than +/-0.8%). We also observed a significant reduction in density along fault lines and interpreted that as due to the presence of multiple cracks caused by mechanical stress during recurrent seismic events. We show that this new type of muography technique can be applied to estimate the terrain density and porosity distribution, thus determining more precise Bouguer reduction densities.

Muographic mapping of the subsurface density structures in Miura, Boso and Izu peninsulas, Japan

PubMed Central

Tanaka, Hiroyuki K. M.

2015-01-01

While the benefits of determining the bulk density distribution of a landmass are evident, established experimental techniques reliant on gravity measurements cannot uniquely determine the underground density distribution. We address this problem by taking advantage of traffic tunnels densely distributed throughout the country. Cosmic ray muon flux is measured in the tunnels to determine the average density of each rock overburden. After analyzing the data collected from 146 observation points in Miura, South-Boso and South-Izu Peninsula, Japan as an example, we mapped out the shallow density distribution of an area of 1340 km2. We find a good agreement between muographically determined density distribution and geologic features as described in existing geological studies. The average shallow density distribution below each peninsula was determined with a great accuracy (less than ±0.8%). We also observed a significant reduction in density along fault lines and interpreted that as due to the presence of multiple cracks caused by mechanical stress during recurrent seismic events. We show that this new type of muography technique can be applied to estimate the terrain density and porosity distribution, thus determining more precise Bouguer reduction densities. PMID:25660352

Muographic mapping of the subsurface density structures in Miura, Boso and Izu peninsulas, Japan.

PubMed

Tanaka, Hiroyuki K M

2015-02-09

While the benefits of determining the bulk density distribution of a landmass are evident, established experimental techniques reliant on gravity measurements cannot uniquely determine the underground density distribution. We address this problem by taking advantage of traffic tunnels densely distributed throughout the country. Cosmic ray muon flux is measured in the tunnels to determine the average density of each rock overburden. After analyzing the data collected from 146 observation points in Miura, South-Boso and South-Izu Peninsula, Japan as an example, we mapped out the shallow density distribution of an area of 1340 km(2). We find a good agreement between muographically determined density distribution and geologic features as described in existing geological studies. The average shallow density distribution below each peninsula was determined with a great accuracy (less than ±0.8%). We also observed a significant reduction in density along fault lines and interpreted that as due to the presence of multiple cracks caused by mechanical stress during recurrent seismic events. We show that this new type of muography technique can be applied to estimate the terrain density and porosity distribution, thus determining more precise Bouguer reduction densities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R., E-mail: spatsour@cc.uoi.gr, E-mail: james.a.klimchuk@nasa.gov

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding ≈50 km s{sup –1}. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe XIV lines at 264.78 and 274.20more » Å is used to determine wing and core densities. We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe XIV lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.« less

Hormone Treatment Restores Bone Density for Young Women with Menopause-Like Condition (Primary Ovarian Insufficiency)

MedlinePlus

... Release Monday, June 9, 2014 Hormone treatment restores bone density for young women with menopause-like condition NIH study reveals way to improve bone health for young women with POI. Researchers at ...

Pyroglutamic acid promotes survival of retinal ganglion cells after optic nerve injury.

PubMed

Oono, Shinichirou; Kurimoto, Takuji; Nakazawa, Toru; Miyoshi, Tomomitsu; Okamoto, Norio; Kashimoto, Ryosuke; Tagami, Yuichi; Ito, Yoshimasa; Mimura, Osamu

2009-07-01

To determine whether pyroglutamic acid (PGA) enhances the survival of retinal ganglion cells (RGCs) after optic nerve (ON) transection in vivo and RGCs in culture. The RGCs of rats were retrogradely labeled by Fluorogold (FG)-soaked sponges placed on both superior colliculi. Seven days later, the ON was transected, and PGA was immediately injected into the vitreous. Seven or fourteen days later, the number of FG-labeled RGCs was counted on flat-mounted retinas to obtain the mean densities of FG-labeled RGCs. To determine whether the survival effect of PGA was related to excitatory amino acid transporter (EAAT), L-trans-pyrrolidine-2,4 dicarboxylate (PDC), a nonselective glutamate transport inhibitor, was injected into vitreous with the PGA. In primary retinal cultures, RGCs were identified as cells that were immunopositive to beta III tubulin three days after beginning the culture with and without PDC. The mean density of FG-labeled RGCs was reduced from 2249 +/- 210 to 920 +/- 202 cells/mm(2) (p < 0.001) on day 7 after the ON transection. The mean density RGCs was significantly higher at 1213 +/- 159 cells/mm(2) after 0.5% PGA injection immediately after the ON transaction than eyes injected with the vehicle at 1007 +/- 122 cells/mm(2) (p = 0.035). One percent PGA was the most effective concentration for survival-promoting effects on RGCs, and the mean density of the RGCs was 1464 +/- 102/mm(2) (p < 0.001). Fourteen days after 1% PGA, the mean density of FG-labeled RGCs was significantly higher than that with vehicle (204 +/- 23/mm(2) versus 145 +/- 17 cells/mm(2); p < 0.01). Simultaneous application of 1% PGA and PDC blocked the survival effects of PGA on day 7 after ON transection. The presence of PGA increased the number of beta III tubulin-positive cells. PGA promotes the survival of axotomized RGCs in adult mammalian retinas possibly mediated by the EAATs.

Noninvasive markers of bone metabolism in the rhesus monkey: normal effects of age and gender

NASA Technical Reports Server (NTRS)

Cahoon, S.; Boden, S. D.; Gould, K. G.; Vailas, A. C.

1996-01-01

Measurement of bone turnover in conditions such as osteoporosis has been limited by the need for invasive iliac bone biopsy to reliably determine parameters of bone metabolism. Recent advances in the area of serum and urinary markers of bone metabolism have raised the possibility for noninvasive measurements; however, little nonhuman primate data exist for these parameters. The purpose of this experiment was to define the normal range and variability of several of the newer noninvasive bone markers which are currently under investigation in humans. The primary intent was to determine age and gender variability, as well as provide some normative data for future experiments in nonhuman primates. Twenty-four rhesus macaques were divided into equal groups of male and female according to the following age groupings: 3 years, 5-10 years, 15-20 years, and > 25 years. Urine was collected three times daily for a four-day period and measured for several markers of bone turnoverm including pyridinoline (PYD), deoxypyrodinoline (DPD), hydroxyproline, and creatinine. Bone mineral density measurements of the lumbar spine were performed at the beginning and end of the study period. Serum was also obtained at the time of bone densitometry for measurement of osteocalcin levels by radioimmunoassay. There were no significant differences in bone mineral density, urine PYD, or urine DPD based on gender. Bone density was lowest in the youngest animals, peaked in the 15-20-year group, but again decreased in the oldest animals. The osteocalcin, PYD, and DPD levels followed an inversely related pattern to bone density. The most important result was the relative age insensitivity of the ratio of PYD:DPD in monkeys up to age 20 years. Since bone density changes take months or years to become measurable and iliac biopsies are invasive, the PYD/DPD marker ratio may have important implications for rapid noninvasive measurement of the effects of potential treatments for osteoporosis in the non-human primate model.

Core and Wing Densities of Asymmetric Coronal Spectral Profiles: Implications for the Mass Supply of the Solar Corona

NASA Astrophysics Data System (ADS)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R.

2014-02-01

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding ≈50 km s-1. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe XIV lines at 264.78 and 274.20 Å is used to determine wing and core densities. We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe XIV lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.

Core and Wing Densities of Asymmetric Coronal Spectral Profiles: Implications for the Mass Supply of the Solar Corona

NASA Technical Reports Server (NTRS)

Patsourakos, S.; Klimchuk, J. A.; Young, P. R.

2014-01-01

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding approximately equal to 50 km per sec. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe(sub XIV) lines at 264.78 and 274.20 Angstroms is used to determine wing and core densities.We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe(sub XIV) lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.

Sleep spindles may predict response to cognitive-behavioral therapy for chronic insomnia.

PubMed

Dang-Vu, Thien Thanh; Hatch, Benjamin; Salimi, Ali; Mograss, Melodee; Boucetta, Soufiane; O'Byrne, Jordan; Brandewinder, Marie; Berthomier, Christian; Gouin, Jean-Philippe

2017-11-01

While cognitive-behavioral therapy for insomnia constitutes the first-line treatment for chronic insomnia, only few reports have investigated how sleep architecture relates to response to this treatment. In this pilot study, we aimed to determine whether pre-treatment sleep spindle density predicts treatment response to cognitive-behavioral therapy for insomnia. Twenty-four participants with chronic primary insomnia participated in a 6-week cognitive-behavioral therapy for insomnia performed in groups of 4-6 participants. Treatment response was assessed using the Pittsburgh Sleep Quality Index and the Insomnia Severity Index measured at pre- and post-treatment, and at 3- and 12-months' follow-up assessments. Secondary outcome measures were extracted from sleep diaries over 7 days and overnight polysomnography, obtained at pre- and post-treatment. Spindle density during stage N2-N3 sleep was extracted from polysomnography at pre-treatment. Hierarchical linear modeling analysis assessed whether sleep spindle density predicted response to cognitive-behavioral therapy. After adjusting for age, sex, and education level, lower spindle density at pre-treatment predicted poorer response over the 12-month follow-up, as reflected by a smaller reduction in Pittsburgh Sleep Quality Index over time. Reduced spindle density also predicted lower improvements in sleep diary sleep efficiency and wake after sleep onset immediately after treatment. There were no significant associations between spindle density and changes in the Insomnia Severity Index or polysomnography variables over time. These preliminary results suggest that inter-individual differences in sleep spindle density in insomnia may represent an endogenous biomarker predicting responsiveness to cognitive-behavioral therapy. Insomnia with altered spindle activity might constitute an insomnia subtype characterized by a neurophysiological vulnerability to sleep disruption associated with impaired responsiveness to cognitive-behavioral therapy. Copyright © 2017 Elsevier B.V. All rights reserved.

Visible red and infrared light alters gene expression in human marrow stromal fibroblast cells.

PubMed

Guo, J; Wang, Q; Wai, D; Zhang, Q Z; Shi, S H; Le, A D; Shi, S T; Yen, S L-K

2015-04-01

This study tested whether or not gene expression in human marrow stromal fibroblast (MSF) cells depends on light wavelength and energy density. Primary cultures of isolated human bone marrow stem cells (hBMSC) were exposed to visible red (VR, 633 nm) and infrared (IR, 830 nm) radiation wavelengths from a light emitting diode (LED) over a range of energy densities (0.5, 1.0, 1.5, and 2.0 Joules/cm2) Cultured cells were assayed for cell proliferation, osteogenic potential, adipogenesis, mRNA and protein content. mRNA was analyzed by microarray and compared among different wavelengths and energy densities. Mesenchymal and epithelial cell responses were compared to determine whether responses were cell type specific. Protein array analysis was used to further analyze key pathways identified by microarrays. Different wavelengths and energy densities produced unique sets of genes identified by microarray analysis. Pathway analysis pointed to TGF-beta 1 in the visible red and Akt 1 in the infrared wavelengths as key pathways to study. TGF-beta protein arrays suggested switching from canonical to non-canonical TGF-beta pathways with increases to longer IR wavelengths. Microarrays suggest RANKL and MMP 10 followed IR energy density dose-response curves. Epithelial and mesenchymal cells respond differently to stimulation by light suggesting cell type-specific response is possible. These studies demonstrate differential gene expression with different wavelengths, energy densities and cell types. These differences in gene expression have the potential to be exploited for therapeutic purposes and can help explain contradictory results in the literature when wavelengths, energy densities and cell types differ. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Gaetice depressus (Crustacea, Varunidae): Species profile and its role in organic carbon and nitrogen flow

NASA Astrophysics Data System (ADS)

Wahyudi, A'an. J.; Wada, Shigeki; Aoki, Masakazu; Hama, Takeo

2015-06-01

Gaetice depressus is one of the most dominant macrozoobenthos species in boulder shores of intertidal coastal ecosystems in Japan. As recorded in previous studies, this species is also considered as having high density and biomass. Consequently, it is thought to be one of the more important species in the organic matter flow of boulder shores, especially through the food web. In this study, some taxonomic problems related to G. depressus were tackled and the autoecology and ecological processes in the intertidal ecosystem of G. depressus, such as organic matter flow, were investigated. Furthermore, in order to clarify the taxonomy description, resolve inconsistencies in the scientific name, and learn about the life history, a literature review was conducted. Seasonal changes in density, morphology pattern and population structure were determined based on the data obtained in Ebisu Island, Japan. Then, the role of G. depressus was determined by estimating the intake and emittance fluxes of organic carbon and nitrogen through ingestion and egestion process in the boulder shores of Ebisu Island. A feeding rate experiment was also conducted in order to estimate the intake flux by using the catch-release-recapture method. Meanwhile, to estimate the emittance flux, a defecation rate experiment was conducted by catching some individuals of G. depressus, and then incubating them in the laboratory. The feeding rate measured by the speed of diet consumption of G. depressus was about 12.6 mg ind-1 h-1. Considering the average density, the intake flux through the feeding process could be estimated as 25.2 mgC m-2 h-1 and 2.6 mgN m-2 h-1. On the other hand, G. depressus egested fecal pellet at the rate of 5.4 mg ind-1 h-1. The average emittance flux through the fecal pellet egesting process is estimated at 5.6 mgC m-2 h-1 and 0.7 mgN m-2 h-1. Therefore, it can be estimated that about 25% of organic matter from diet is egested as fecal pellet, which means that about 75% of the intake flux of organic carbon and nitrogen is used for the total assimilation of G. depressus. Intake flux was also considered as affecting the high dynamism of primary producer consumption. The total population of G. depressus is estimated to consume about 18.4% of primary producer in average throughout the year. Therefore, the turnover time of primary producer by consumption of G. depressus was about five days.

Plume propagation direction determination with SO2 cameras

NASA Astrophysics Data System (ADS)

Klein, Angelika; Lübcke, Peter; Bobrowski, Nicole; Kuhn, Jonas; Platt, Ulrich

2017-03-01

SO2 cameras are becoming an established tool for measuring sulfur dioxide (SO2) fluxes in volcanic plumes with good precision and high temporal resolution. The primary result of SO2 camera measurements are time series of two-dimensional SO2 column density distributions (i.e. SO2 column density images). However, it is frequently overlooked that, in order to determine the correct SO2 fluxes, not only the SO2 column density, but also the distance between the camera and the volcanic plume, has to be precisely known. This is because cameras only measure angular extents of objects while flux measurements require knowledge of the spatial plume extent. The distance to the plume may vary within the image array (i.e. the field of view of the SO2 camera) since the plume propagation direction (i.e. the wind direction) might not be parallel to the image plane of the SO2 camera. If the wind direction and thus the camera-plume distance are not well known, this error propagates into the determined SO2 fluxes and can cause errors exceeding 50 %. This is a source of error which is independent of the frequently quoted (approximate) compensation of apparently higher SO2 column densities and apparently lower plume propagation velocities at non-perpendicular plume observation angles.Here, we propose a new method to estimate the propagation direction of the volcanic plume directly from SO2 camera image time series by analysing apparent flux gradients along the image plane. From the plume propagation direction and the known location of the SO2 source (i.e. volcanic vent) and camera position, the camera-plume distance can be determined. Besides being able to determine the plume propagation direction and thus the wind direction in the plume region directly from SO2 camera images, we additionally found that it is possible to detect changes of the propagation direction at a time resolution of the order of minutes. In addition to theoretical studies we applied our method to SO2 flux measurements at Mt Etna and demonstrate that we obtain considerably more precise (up to a factor of 2 error reduction) SO2 fluxes. We conclude that studies on SO2 flux variability become more reliable by excluding the possible influences of propagation direction variations.

Comparison of simulation results with sea-level experimental data on 10(14) - 10(16) air shower cores

NASA Technical Reports Server (NTRS)

Ash, A. G.

1985-01-01

Simulation predictions for the Leeds 35 sq m horizontal discharge chamber array for proton primaries with a approx. E sup 2.7 spectrum extrapolated from balloon data to 10 to the 16th power eV give power law rho (r)-spectra with constant slope approx. -2 consistent with the experimental data up to the point at which they steepen but overshooting them at higher densities, and at high shower sizes predicted cores which are significantly steeper than those observed. Further comparisons with results for heavy nuclei primaries (up to A = 56) point to the inadequacy of changes in primary composition to account for the observed density spectra and core flattening, and the shower size spectrum together, and point, therefore, to the failure of the scaling interaction model at approx. 10 to the 15th power eV primary energy.

An adaptive two-stage sequential design for sampling rare and clustered populations

USGS Publications Warehouse

Brown, J.A.; Salehi, M.M.; Moradi, M.; Bell, G.; Smith, D.R.

2008-01-01

How to design an efficient large-area survey continues to be an interesting question for ecologists. In sampling large areas, as is common in environmental studies, adaptive sampling can be efficient because it ensures survey effort is targeted to subareas of high interest. In two-stage sampling, higher density primary sample units are usually of more interest than lower density primary units when populations are rare and clustered. Two-stage sequential sampling has been suggested as a method for allocating second stage sample effort among primary units. Here, we suggest a modification: adaptive two-stage sequential sampling. In this method, the adaptive part of the allocation process means the design is more flexible in how much extra effort can be directed to higher-abundance primary units. We discuss how best to design an adaptive two-stage sequential sample. ?? 2008 The Society of Population Ecology and Springer.

Malarial Anaemia and Anaemia Severity in Apparently Healthy Primary School Children in Urban and Rural Settings in the Mount Cameroon Area: Cross Sectional Survey

PubMed Central

Ndamukong-Nyanga, Judith Lum; Nweboh, Malaika; Anchang-Kimbi, Judith Kuoh; Lum, Emmaculate; Nana, Yannick; Ndamukong, Kenneth K. J.; Lehman, Leopold G.

2015-01-01

Background This study examines the relative importance of living in an urban versus rural setting and malaria in contributing to the public health problem of malarial anaemia (MA) and anaemia respectively in apparently healthy primary school children. Methods A cross-sectional study was conducted among 727 school children aged between four and 15 years living in an urban (302) and rural (425) settings in the Mount Cameroon area. Blood sample collected from each child was used for the preparation of blood films for detection of malaria parasites and assessment of malaria parasite density as well as full blood count determination using an automated haematology analyzer. Based on haemoglobin (Hb) measurements, children with malaria parasitaemia were stratified into MA (Hb<11g/dL); mild MA (Hb of 8–10.9g/dL); moderate MA (Hb of 6.1–7.9g/dL) and severe MA (Hb≤6g/dL). Evaluation of potential determinants of MA and anaemia was performed by multinomial logistic-regression analysis and odds ratios used to evaluate risk factors. Results Out of the 727 children examined, 72 (9.9%) had MA. The prevalence of MA and anaemia were significantly higher (χ2 = 36.5, P <0.001; χ2 = 16.19, P <0.001 respectively) in children in the urban (17.9%; 26.8% respectively) than in the rural area (4.2%; 14.8% respectively). Majority of the MA cases were mild (88.9%), with moderate (5.6%) and severe MA (5.6%) occurring in the urban area only. The age group ≤6years was significantly (P <0.05) associated with both MA and anaemia. In addition, low parasite density was associated with MA while malaria parasite negative and microcytosis were associated with anaemia. Conclusions Malarial anaemia and anaemia display heterogeneity and complexity that differ with the type of settlement. The presence of severe MA and the contributions of the age group ≤6 years, low parasite density and microcytosis to the public health problem of MA and anaemia are noteworthy. PMID:25893500

Malarial anaemia and anaemia severity in apparently healthy primary school children in urban and rural settings in the Mount Cameroon area: cross sectional survey.

PubMed

Sumbele, Irene Ule Ngole; Kimbi, Helen Kuokuo; Ndamukong-Nyanga, Judith Lum; Nweboh, Malaika; Anchang-Kimbi, Judith Kuoh; Lum, Emmaculate; Nana, Yannick; Ndamukong, Kenneth K J; Lehman, Leopold G

2015-01-01

This study examines the relative importance of living in an urban versus rural setting and malaria in contributing to the public health problem of malarial anaemia (MA) and anaemia respectively in apparently healthy primary school children. A cross-sectional study was conducted among 727 school children aged between four and 15 years living in an urban (302) and rural (425) settings in the Mount Cameroon area. Blood sample collected from each child was used for the preparation of blood films for detection of malaria parasites and assessment of malaria parasite density as well as full blood count determination using an automated haematology analyzer. Based on haemoglobin (Hb) measurements, children with malaria parasitaemia were stratified into MA (Hb<11 g/dL); mild MA (Hb of 8-10.9 g/dL); moderate MA (Hb of 6.1-7.9 g/dL) and severe MA (Hb≤6 g/dL). Evaluation of potential determinants of MA and anaemia was performed by multinomial logistic-regression analysis and odds ratios used to evaluate risk factors. Out of the 727 children examined, 72 (9.9%) had MA. The prevalence of MA and anaemia were significantly higher (χ2 = 36.5, P <0.001; χ2 = 16.19, P <0.001 respectively) in children in the urban (17.9%; 26.8% respectively) than in the rural area (4.2%; 14.8% respectively). Majority of the MA cases were mild (88.9%), with moderate (5.6%) and severe MA (5.6%) occurring in the urban area only. The age group ≤6 years was significantly (P <0.05) associated with both MA and anaemia. In addition, low parasite density was associated with MA while malaria parasite negative and microcytosis were associated with anaemia. Malarial anaemia and anaemia display heterogeneity and complexity that differ with the type of settlement. The presence of severe MA and the contributions of the age group ≤6 years, low parasite density and microcytosis to the public health problem of MA and anaemia are noteworthy.

Vertical Distribution of Pasteuria penetrans Parasitizing Meloidogyne incognita on Pittosporum tobira in Florida.

PubMed

Baidoo, Richard; Mengistu, Tesfamariam Mekete; Brito, Janete A; McSorley, Robert; Stamps, Robert H; Crow, William T

2017-09-01

Pasteuria penetrans is considered as the primary agent responsible for soil suppressiveness to root-knot nematodes widely distributed in many agricultural fields. A preliminary survey on a Pittosporum tobira field where the grower had experienced a continuous decline in productivity caused by Meloidogyne incognita showed that the nematode was infected with Pasteuria penetrans . For effective control of the nematode, the bacterium and the host must coexist in the same root zone. The vertical distribution of Pasteuria penetrans and its relationship with the nematode host in the soil was investigated to identify (i) the vertical distribution of P. penetrans endospores in an irrigated P. tobira field and (ii) the relationship among P. penetrans endospore density, M. incognita J2 population density, and host plant root distribution over time. Soil bioassays revealed that endospore density was greater in the upper 18 cm of the top soil compared with the underlying depths. A correlation analysis showed that the endospore density was positively related to the J2 population density and host plant root distribution. Thus, the vertical distribution of P. penetrans was largely dependent on its nematode host which in turn was determined by the distribution of the host plant roots. The Pasteuria was predominant mostly in the upper layers of the soil where their nematode host and the plant host roots are abundant, a factor which may be a critical consideration when using P. penetrans as a nematode biological control agent.

Vertical Distribution of Pasteuria penetrans Parasitizing Meloidogyne incognita on Pittosporum tobira in Florida

PubMed Central

Baidoo, Richard; Mengistu, Tesfamariam Mekete; Brito, Janete A.; McSorley, Robert; Stamps, Robert H.; Crow, William T.

2017-01-01

Pasteuria penetrans is considered as the primary agent responsible for soil suppressiveness to root-knot nematodes widely distributed in many agricultural fields. A preliminary survey on a Pittosporum tobira field where the grower had experienced a continuous decline in productivity caused by Meloidogyne incognita showed that the nematode was infected with Pasteuria penetrans. For effective control of the nematode, the bacterium and the host must coexist in the same root zone. The vertical distribution of Pasteuria penetrans and its relationship with the nematode host in the soil was investigated to identify (i) the vertical distribution of P. penetrans endospores in an irrigated P. tobira field and (ii) the relationship among P. penetrans endospore density, M. incognita J2 population density, and host plant root distribution over time. Soil bioassays revealed that endospore density was greater in the upper 18 cm of the top soil compared with the underlying depths. A correlation analysis showed that the endospore density was positively related to the J2 population density and host plant root distribution. Thus, the vertical distribution of P. penetrans was largely dependent on its nematode host which in turn was determined by the distribution of the host plant roots. The Pasteuria was predominant mostly in the upper layers of the soil where their nematode host and the plant host roots are abundant, a factor which may be a critical consideration when using P. penetrans as a nematode biological control agent. PMID:29062154

What FIREs Up Star Formation: the Emergence of the Kennicutt-Schmidt Law from Feedback

NASA Astrophysics Data System (ADS)

Orr, Matthew E.; Hayward, Christopher C.; Hopkins, Philip F.; Chan, T. K.; Faucher-Giguère, Claude-André; Feldmann, Robert; Kereš, Dušan; Murray, Norman; Quataert, Eliot

2018-05-01

We present an analysis of the global and spatially-resolved Kennicutt-Schmidt (KS) star formation relation in the FIRE (Feedback In Realistic Environments) suite of cosmological simulations, including halos with z = 0 masses ranging from 1010 - 1013 M⊙. We show that the KS relation emerges and is robustly maintained due to the effects of feedback on local scales regulating star-forming gas, independent of the particular small-scale star formation prescriptions employed. We demonstrate that the time-averaged KS relation is relatively independent of redshift and spatial averaging scale, and that the star formation rate surface density is weakly dependent on metallicity and inversely dependent on orbital dynamical time. At constant star formation rate surface density, the `Cold & Dense' gas surface density (gas with T < 300 K and n > 10 cm-3, used as a proxy for the molecular gas surface density) of the simulated galaxies is ˜0.5 dex less than observed at ˜kpc scales. This discrepancy may arise from underestimates of the local column density at the particle-scale for the purposes of shielding in the simulations. Finally, we show that on scales larger than individual giant molecular clouds, the primary condition that determines whether star formation occurs is whether a patch of the galactic disk is thermally Toomre-unstable (not whether it is self-shielding): once a patch can no longer be thermally stabilized against fragmentation, it collapses, becomes self-shielding, cools, and forms stars, regardless of epoch or environment.

The effect of the ambient plasma conditions on the variation of charge on dust grains

NASA Astrophysics Data System (ADS)

Chakraborty, M.; Kausik, S. S.; Saikia, B. K.; Kakati, M.; Bujarbarua, S.

2003-02-01

An experimental study has been performed into the variation of charge on dust grains with change in the ambient plasma conditons. A dust beam containing submicron sized silver grains was passed through plasma. The dust grains were charged by the plasma particles as well as by primary electrons from the filament. An increase in the filament current increased both the plasma density and the number density of the primary electrons. The grain charge was found out both from the deflection of the dust grains and also from the floating potential. The experimental observations shows that the secondary emission caused by the primary electrons significantly influenced and played a prominent role in the establishment of charge on the grains.

Bone health status of postmenopausal Chinese women.

PubMed

Lo, Sue S T

2015-12-01

To evaluate the prevalence of osteoporosis in treatment-naïve postmenopausal women, their treatment adherence, and the risk factors for osteoporosis. Cross-sectional study of bone density reports, a self-administered health checklist, and computerised consultation records. Primary care sexual and reproductive health service in Hong Kong. Postmenopausal Chinese women who had never received osteoporosis treatment or hormone replacement therapy. Each woman completed a checklist of risk factors for osteoporosis, menopause age, history of hormone replacement therapy, and osteoporosis treatment prior to undergoing bone mineral density measurement at the postero-anterior lumbar spine and left femur. The consultation records of those with osteoporosis were reviewed to determine their treatment adherence. T-score at the spine and hip, presence or absence of risk factors for osteoporosis, and treatment adherence. Between January 2008 and December 2011, 1507 densitometries were performed for eligible women; 51.6% of whom were diagnosed with osteopenia and 25.7% with osteoporosis. The mean age of women with normal bone mineral density, osteopenia, and osteoporosis was 57.0, 58.0, and 59.7 years, respectively. Approximately half of them had an inadequate dietary calcium intake, performed insufficient weight-bearing exercise, or had too little sun exposure. Logistic regression analysis revealed that age, body mass index of <18.5 kg/m(2), parental history of osteoporosis or hip fracture, and duration of menopause were significant risk factors for osteoporosis. Among those with osteoporosis, 42.9% refused treatment, 30.7% complied with treatment, and 26.3% discontinued treatment or defaulted from follow-up. Those who refused treatment were significantly older. Osteoporosis is prevalent in postmenopausal women. Only 50% adopted primary prevention strategies. Almost 70% refused treatment or stopped prematurely.

Determining the efficacy of guppies and pyriproxyfen (Sumilarv® 2MR) combined with community engagement on dengue vectors in Cambodia: study protocol for a randomized controlled trial.

PubMed

Hustedt, John; Doum, Dyna; Keo, Vanney; Ly, Sokha; Sam, BunLeng; Chan, Vibol; Alexander, Neal; Bradley, John; Prasetyo, Didot Budi; Rachmat, Agus; Muhammad, Shafique; Lopes, Sergio; Leang, Rithea; Hii, Jeffrey

2017-08-04

Evidence on the effectiveness of low-cost, sustainable, biological vector-control tools for the Aedes mosquitoes is limited. Therefore, the purpose of this trial is to estimate the impact of guppy fish (guppies), in combination with the use of the larvicide pyriproxyfen (Sumilarv® 2MR), and Communication for Behavioral Impact (COMBI) activities to reduce entomological indices in Cambodia. In this cluster randomized controlled, superiority trial, 30 clusters comprising one or more villages each (with approximately 170 households) will be allocated, in a 1:1:1 ratio, to receive either (1) three interventions (guppies, Sumilarv® 2MR, and COMBI activities), (2) two interventions (guppies and COMBI activities), or (3) control (standard vector control). Households will be invited to participate, and entomology surveys among 40 randomly selected households per cluster will be carried out quarterly. The primary outcome will be the population density of adult female Aedes mosquitoes (i.e., number per house) trapped using adult resting collections. Secondary outcome measures will include the House Index, Container Index, Breteau Index, Pupae Per House, Pupae Per Person, mosquito infection rate, guppy fish coverage, Sumilarv® 2MR coverage, and percentage of respondents with knowledge about Aedes mosquitoes causing dengue. In the primary analysis, adult female Aedes density and mosquito infection rates will be aggregated over follow-up time points to give a single rate per cluster. This will be analyzed by negative binomial regression, yielding density ratios. This trial is expected to provide robust estimates of the intervention effect. A rigorous evaluation of these vector-control interventions is vital to developing an evidence-based dengue control strategy and to help direct government resources. Current Controlled Trials, ID: ISRCTN85307778 . Registered on 25 October 2015.

Evaluation of interference fit and bone damage of an uncemented femoral knee implant.

PubMed

Berahmani, Sanaz; Hendriks, Maartje; de Jong, Joost J A; van den Bergh, Joop P W; Maal, Thomas; Janssen, Dennis; Verdonschot, Nico

2018-01-01

During implantation of an uncemented femoral knee implant, press-fit interference fit provides the primary stability. It is assumed that during implantation a combination of elastic and plastic deformation and abrasion of the bone will occur, but little is known about what happens at the bone-implant interface and how much press-fit interference fit is eventually achieved. Five cadaveric femora were prepared and implantation was performed by an experienced surgeon. Micro-CT- and conventional CT-scans were obtained pre- and post-implantation for geometrical measurements and to measure bone mineral density. Additionally, the position of the implant with respect to the bone was determined by optical scanning of the reconstructions. By measuring the differences in surface geometry, assessments were made of the cutting error, the actual interference fit, the amount of bone damage, and the effective interference fit. Our analysis showed an average cutting error of 0.67mm (SD 0.17mm), which pointed mostly towards bone under-resections. We found an average actual AP interference fit of 1.48mm (SD 0.27mm), which was close to the nominal value of 1.5mm. We observed combinations of bone damage and elastic deformation in all bone specimens, which showed a trend to be related with bone density. Higher bone density tended to lead to lower bone damage and higher elastic deformation. The results of the current study indicate different factors that interact while implanting an uncemented femoral knee component. This knowledge can be used to fine-tune design criteria of femoral components to achieve adequate primary stability for all patients. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of biodiversity changes in disease risk: exploring disease emergence in a plant-virus system.

PubMed

Pagán, Israel; González-Jara, Pablo; Moreno-Letelier, Alejandra; Rodelo-Urrego, Manuel; Fraile, Aurora; Piñero, Daniel; García-Arenal, Fernando

2012-01-01

The effect of biodiversity on the ability of parasites to infect their host and cause disease (i.e. disease risk) is a major question in pathology, which is central to understand the emergence of infectious diseases, and to develop strategies for their management. Two hypotheses, which can be considered as extremes of a continuum, relate biodiversity to disease risk: One states that biodiversity is positively correlated with disease risk (Amplification Effect), and the second predicts a negative correlation between biodiversity and disease risk (Dilution Effect). Which of them applies better to different host-parasite systems is still a source of debate, due to limited experimental or empirical data. This is especially the case for viral diseases of plants. To address this subject, we have monitored for three years the prevalence of several viruses, and virus-associated symptoms, in populations of wild pepper (chiltepin) under different levels of human management. For each population, we also measured the habitat species diversity, host plant genetic diversity and host plant density. Results indicate that disease and infection risk increased with the level of human management, which was associated with decreased species diversity and host genetic diversity, and with increased host plant density. Importantly, species diversity of the habitat was the primary predictor of disease risk for wild chiltepin populations. This changed in managed populations where host genetic diversity was the primary predictor. Host density was generally a poorer predictor of disease and infection risk. These results support the dilution effect hypothesis, and underline the relevance of different ecological factors in determining disease/infection risk in host plant populations under different levels of anthropic influence. These results are relevant for managing plant diseases and for establishing conservation policies for endangered plant species.

Feasibility of development of a nuclear density gage for determining the density of plastic concrete at a particular stratum : final report.

DOT National Transportation Integrated Search

1981-05-01

Development of a nuclear density gage for determining the degree of consolidation of plastic concrete in selected horizontal layers was determined to be feasible. A commercially available, with some modifications, two-probe density gage (detector in ...

Five-Year Wilkinson Microwave Anisotropy Probe (WMAP) Observations: Data Processing, Sky Maps, and Basic Results

NASA Technical Reports Server (NTRS)

Weiland, J.L.; Hill, R.S.; Odegard, 3.; Larson, D.; Bennett, C.L.; Dunkley, J.; Jarosik, N.; Page, L.; Spergel, D.N.; Halpern, M.;

Lightweight structure design for supporting plate of primary mirror

NASA Astrophysics Data System (ADS)

Wang, Xiao; Wang, Wei; Liu, Bei; Qu, Yan Jun; Li, Xu Peng

2017-10-01

A topological optimization design for the lightweight technology of supporting plate of the primary mirror is presented in this paper. The supporting plate of the primary mirror is topologically optimized under the condition of determined shape, loads and environment. And the optimal structure is obtained. The diameter of the primary mirror in this paper is 450mm, and the material is SiC1 . It is better to select SiC/Al as the supporting material. Six points of axial relative displacement can be used as constraints in optimization2 . Establishing the supporting plate model and setting up the model parameters. After analyzing the force of the main mirror on the supporting plate, the model is applied with force and constraints. Modal analysis and static analysis of supporting plates are calculated. The continuum structure topological optimization mathematical model is created with the variable-density method. The maximum deformation of the surface of supporting plate under the gravity of the mirror and the first model frequency are assigned to response variable, and the entire volume of supporting structure is converted to object function. The structures before and after optimization are analyzed using the finite element method. Results show that the optimized fundamental frequency increases 29.85Hz and has a less displacement compared with the traditional structure.

Growth of ponderosa pine thinned to different stocking levels in central Oregon: 30-year results.

Treesearch

P.H. Cochran; James W. Barrett

1999-01-01

Periodic annual increments (PAI) for survivor diameters decreased curvilinearly with increasing stand density. Gross volume and basal areas PAIs increased linearly with increasing stand density. Growth of basal area and volume for the 20 largest trees per acre were reduced curvilinearly with increasing stand density. Bark beetles were the primary cause of mortality. No...

Direct Measurement of Impurity Transport in a Field Reversed Configuration

NASA Astrophysics Data System (ADS)

Roche, T.; Bolte, N.; Heidbrink, W. W.; McWilliams, R.; Wessel, F.

2011-10-01

An optical tomography system has been developed and implemented in the Flux Coil Generated Field Reversed Configuration (FCG-FRC) at Tri Alpha Energy. Sixteen chords view ~ 35 % of the FRC at the mid-plane. The chords are arranged in two identical fans of eight chords each. To measure transport of an impurity species, argon, an FRC is generated using either Nitrogen or Deuterium as the primary species. A puff valve is activated prior to the shot such that the argon begins to bleed in to the vacuum chamber as the FRC is formed. The gas is puffed at the optimal location for tomographic reconstruction. Each chord is collimated to illuminate a fiber optic cable which is fed to an array of photomultiplier tubes which are fitted with neutral density and band pass filters to allow the appropriate amount of light from the emitting, singly ionized, argon at 434 . 8 nm to be measured. Using a preliminary assumption that density of argon is proportional to light intensity gathered data have been used to reconstruct density profiles. These profiles often peak near the field null. The data are being analyzed to determine diffusive and convective transport coefficients.

Design and performance of a pulse transformer based on Fe-based nanocrystalline core.

PubMed

Yi, Liu; Xibo, Feng; Lin, Fuchang

2011-08-01

A dry-type pulse transformer based on Fe-based nanocrystalline core with a load of 0.88 nF, output voltage of more than 65 kV, and winding ratio of 46 is designed and constructed. The dynamic characteristics of Fe-based nanocrystalline core under the impulse with the pulse width of several microseconds were studied. The pulse width and incremental flux density have an important effect on the pulse permeability, so the pulse permeability is measured under a certain pulse width and incremental flux density. The minimal volume of the toroidal pulse transformer core is determined by the coupling coefficient, the capacitors of the resonant charging circuit, incremental flux density, and pulse permeability. The factors of the charging time, ratio, and energy transmission efficiency in the resonant charging circuit based on magnetic core-type pulse transformer are analyzed. Experimental results of the pulse transformer are in good agreement with the theoretical calculation. When the primary capacitor is 3.17 μF and charge voltage is 1.8 kV, a voltage across the secondary capacitor of 0.88 nF with peak value of 68.5 kV, rise time (10%-90%) of 1.80 μs is obtained.

[The expression of IDH1 (R132H) is positively correlated with cell proliferation and angiogenesis in glioma samples].

PubMed

Shi, Jiankuan; Zhao, Yuanlin; Yuan, Yuan; Wang, Chao; Xie, Zhonglin; Gao, Xing; Xiao, Liming; Ye, Jing

2016-03-01

To explore the correlations of the expression of mutant isocitrate dehydrogenase (IDH1) (R132H) protein with angiogenesis and cell proliferation in glioma. We performed polymerase chain reaction-based IDH gene mutation screening in 385 glioma samples, and the subcellular localization and expression levels of IDH1 (R132H) was examined by immunohistochemistry (IHC). Ki-67 labeling index was introduced to determine the proliferation of glioma cells, and the microvessel density was measured through CD34 staining. Statistical analyses were performed to show the correlations of IDH1 mutation with cell proliferation and microvessel density. The mutant rates of IDH1 were about 50%-60% in grade II-III gliomas and secondary glioblastomas, which were significantly higher than those in pilocytic astrocytoma (grade I) and primary glioblastoma (grade IV). Moreover, the level of IDH1 (R132H) protein was positively correlated with Ki-67 labeling index and microvessel density. IDH mutation was common in grade II-III glioma and secondary glioblastoma, and the mutant IDH1 (R132H) might play a critical role in the cell proliferation and angiogenesis of glioma.

Ecological drivers of guanaco recruitment: variable carrying capacity and density dependence.

PubMed

Marino, Andrea; Pascual, Miguel; Baldi, Ricardo

2014-08-01

Ungulates living in predator-free reserves offer the opportunity to study the influence of food limitation on population dynamics without the potentially confounding effects of top-down regulation or livestock competition. We assessed the influence of relative forage availability and population density on guanaco recruitment in two predator-free reserves in eastern Patagonia, with contrasting scenarios of population density. We also explored the relative contribution of the observed recruitment to population growth using a deterministic linear model to test the assumption that the studied populations were closed units. The observed densities increased twice as fast as our theoretical populations, indicating that marked immigration has taken place during the recovery phase experienced by both populations, thus we rejected the closed-population assumption. Regarding the factors driving variation in recruitment, in the low- to medium-density setting, we found a positive linear relationship between recruitment and surrogates of annual primary production, whereas no density dependence was detected. In contrast, in the high-density scenario, both annual primary production and population density showed marked effects, indicating a positive relationship between recruitment and per capita food availability above a food-limitation threshold. Our results support the idea that environmental carrying capacity fluctuates in response to climatic variation, and that these fluctuations have relevant consequences for herbivore dynamics, such as amplifying density dependence in drier years. We conclude that including the coupling between environmental variability in resources and density dependence is crucial to model ungulate population dynamics; to overlook temporal changes in carrying capacity may even mask density dependence as well as other important processes.

Modeling of reduced effective secondary electron emission yield from a velvet surface

DOE PAGES

Swanson, Charles; Kaganovich, Igor D.

2016-12-05

Complex structures on a material surface can significantly reduce total secondary electron emission from that surface. A velvet is a surface that consists of an array of vertically standing whiskers. The reduction occurs due to the capture of low-energy, true secondary electrons emitted at the bottom of the structure and on the sides of the velvet whiskers. We performed numerical simulations and developed an approximate analytical model that calculates the net secondary electron emission yield from a velvet surface as a function of the velvet whisker length and packing density, and the angle of incidence of primary electrons. We foundmore » that to suppress secondary electrons, the following condition on dimensionless parameters must be met: (π/2) DΑ tan θ >> 1, where theta is the angle of incidence of the primary electron from the normal, D is the fraction of surface area taken up by the velvet whisker bases, and A is the aspect ratio, A = h/r, the ratio of height to radius of the velvet whiskers. We find that velvets available today can reduce the secondary electron yield by 90% from the value of a flat surface. As a result, the values of optimal velvet whisker packing density that maximally suppresses the secondary electron emission yield are determined as a function of velvet aspect ratio and the electron angle of incidence.« less

Light Limitation within Southern New Zealand Kelp Forest Communities

PubMed Central

Desmond, Matthew J.; Pritchard, Daniel W.; Hepburn, Christopher D.

2015-01-01

Light is the fundamental driver of primary productivity in the marine environment. Reduced light availability has the potential to alter the distribution, community composition, and productivity of key benthic primary producers, potentially reducing habitat and energy provision to coastal food webs. We compared the underwater light environment of macroalgal dominated shallow subtidal rocky reef habitats on a coastline modified by human activities with a coastline of forested catchments. Key metrics describing the availability of photosynthetically active radiation (PAR) were determined over 295 days and were related to macroalgal depth distribution, community composition, and standing biomass patterns, which were recorded seasonally. Light attenuation was more than twice as high in shallow subtidal zones along the modified coast. Macroalgal biomass was 2–5 times greater within forested sites, and even in shallow water (2m) a significant difference in biomass was observed. Long-term light dose provided the best explanation for differences in observed biomass between modified and forested coasts, with light availability over the study period differing by 60 and 90 mol photons m−2 at 2 and 10 metres, respectively. Higher biomass on the forested coast was driven by the presence of larger individuals rather than species diversity or density. This study suggests that commonly used metrics such as species diversity and density are not as sensitive as direct measures of biomass when detecting the effects of light limitation within macroalgal communities. PMID:25902185

Programmed death ligand 1 expression and CD8+ tumor-infiltrating lymphocyte density differences between paired primary and brain metastatic lesions in non-small cell lung cancer.

PubMed

Zhou, Jie; Gong, Zhihua; Jia, Qingzhu; Wu, Yan; Yang, Zhen-Zhou; Zhu, Bo

2018-04-15

Immunotherapy targeting the programmed cell death-1/programmed death ligand 1(PD-L1) pathway has shown promising antitumor activity in brain metastases (BMs) of non-small cell lung cancer (NSCLC) patients with an acceptable safety profile; however, the response rates often differ between primary lesions and intracranial lesions. Studies are necessary to identify detailed characterizations of the response biomarkers. In this study, we aimed to compare the differences of PD-L1 expression and CD8 + tumor-infiltrating lymphocyte (TIL) density, two major response biomarkers of PD-1/PD-L1 blockade, between paired primary and brain metastatic lesions in advanced NSCLC. We observed that among primary lesions or BMs, only a small number of patients harbored common PD-L1 expression on both tumor cells and tumor-infiltrating immune cells. Additionally, we found that the numbers of CD8 + TILs were significantly fewer in BMs than in primary lung cancers. Low stromal CD8 + TIL numbers in BMs were associated with significantly shorter overall survival compared to high stromal CD8 + TIL counts. Notably, we demonstrated a discrepancy in PD-L1 expression and CD8 + TIL density between primary lung cancers and their corresponding BMs. Such heterogeneities are significantly associated with the time at which BMs occurred. Our study emphasizes the spatial and temporal heterogeneity of biomarkers for anti-PD-1/PD-L1 therapy, which should be concerned in clinical practice. Copyright © 2018 Elsevier Inc. All rights reserved.

Long-Term Follow-Up of Primary Medical Versus Surgical Treatment of Prolactinomas in Men: Effects on Hyperprolactinemia, Hypogonadism, and Bone Health.

PubMed

Andereggen, Lukas; Frey, Janine; Andres, Robert H; El-Koussy, Marwan; Beck, Jürgen; Seiler, Rolf W; Christ, Emanuel

2017-01-01

In men with prolactinomas, impaired bone density is the principle consequence of hyperprolactinemia-induced hypogonadism. Although dopamine agonists (DAs) are the first-line approach in prolactinomas, surgery can be considered in selected cases. In this study, we aimed to investigate the long-term control of hyperprolactinemia, hypogonadism, and bone health comparing primary medical and surgical therapy in men who had not had prior DA treatment. This is a retrospective case-note study of 44 consecutive men with prolactinomas and no prior DAs managed in a single tertiary referral center. Clinical, biochemical, and radiologic response to the first-line approach were analyzed in the 2 cohorts. Mean age at diagnosis was 47 years (range, 22-78 years). The prevalence of hypogonadism was 86%, and 27% of patients had pathologic bone density at baseline. The primary therapeutic strategy was surgery for 34% and DAs for 66% of patients. Median long-term follow-up was 63 months (range, 17-238 months). Long-term control of hyperprolactinemia required DAs in 53% of patients with primary surgical therapy, versus 90% of patients with primary medical therapy (P = 0.02). Hypogonadism was controlled in 73% of patients. The prevalence of patients with pathologic bone density was 37% at last follow-up, with no differences between the 2 therapeutic cohorts (P = 0.48). Despite control of hyperprolactinemia and hypogonadism in most patients independent of the primary treatment modality, the prevalence of impaired bone health status remains high, and osteodensitometry should be recommended. Copyright © 2016 Elsevier Inc. All rights reserved.

Characterisation and optimisation of PECVD SiNx as an antireflection coating and passivation layer for silicon solar cells

NASA Astrophysics Data System (ADS)

Wan, Yimao; McIntosh, Keith R.; Thomson, Andrew F.

2013-03-01

In this work, we investigate how the film properties of silicon nitride (SiNx) depend on its deposition conditions when formed by plasma enhanced chemical vapour deposition (PECVD). The examination is conducted with a Roth & Rau AK400 PECVD reactor, where the varied parameters are deposition temperature, pressure, gas flow ratio, total gas flow, microwave plasma power and radio-frequency bias voltage. The films are evaluated by Fourier transform infrared spectroscopy to determine structural properties, by spectrophotometry to determine optical properties, and by capacitance-voltage and photoconductance measurements to determine electronic properties. After reporting on the dependence of SiNx properties on deposition parameters, we determine the optimized deposition conditions that attain low absorption and low recombination. On the basis of SiNx growth models proposed in the literature and of our experimental results, we discuss how each process parameter affects the deposition rate and chemical bond density. We then focus on the effective surface recombination velocity Seff, which is of primary importance to solar cells. We find that for the SiNx prepared in this work, 1) Seff does not correlate universally with the bulk structural and optical properties such as chemical bond densities and refractive index, and 2) Seff depends primarily on the defect density at the SiNx-Si interface rather than the insulator charge. Finally, employing the optimized deposition condition, we achieve a relatively constant and low Seff,UL on low-resistivity (≤1.1 Ωcm) p- and n-type c-Si substrates over a broad range of n = 1.85-4.07. The results of this study demonstrate that the trade-off between optical transmission and surface passivation can be circumvented. Although we focus on photovoltaic applications, this study may be useful for any device for which it is desirable to maximize light transmission and surface passivation.

Analysis of the neutron time-of-flight spectra from inertial confinement fusion experiments

DOE PAGES

Hatarik, R.; Sayre, D. B.; Caggiano, J. A.; ...

2015-11-12

For a long time, neutron time-of-flight diagnostics been used to characterize the neutron spectrum produced by inertial confinement fusion experiments. The primary diagnostic goals are to extract the d+t→n+α (DT) and d+d→n+³He (DD) neutron yields and peak widths, and the amount DT scattering relative to its unscattered yield, which is also known as the down-scatter ratio (DSR). These quantities are used to infer yield weighted plasma conditions, such as ion temperature (T ion) and cold fuel areal density. We explain such novel methodologies used to determine neutron yield, apparent T ion and DSR.

Exercise-induced amenorrhea and bone health in the adolescent athlete.

PubMed

Warren, Michelle P; Chua, Abigail T

2008-01-01

Female participation in high school athletics has increased 800% in the last 30 years. The problem of exercise-induced amenorrhea was initially thought to be analogous to hypoestrogenism, but recent studies suggest that nutritional issues underlie most of the pathophysiology and that the mechanism is different from that seen in the primary hypogonadal state. Exercise-induced amenorrhea can be an indicator of an energy drain, and the presence of the other components of the female athlete triad-bone density loss and eating disorders-must be determined as well. Addressing skeletal problems related to nutritional and hormonal deficiencies in this population is of very high priority.

Experimental studies of combustion in a two dimensional free shear layer

NASA Technical Reports Server (NTRS)

Pitz, R. W.; Daily, J. W.

1979-01-01

The effect of combustion on the turbulent free shear layer formed at a rearward facing step has been studied. Schlieren movies confirm the importance of large scale vortices in determining entrainment and mixing behavior. The movies, long exposure schlieren photographs, and laser anemometry velocity profiles are used to observe the spreading rate of the layer and to study the vortex formation process. It is concluded that to first order, the primary effect of combustion is felt through the change in density ratio across the layer and acceleration of the flow due to volumetric expansion of the fluid in a confined duct.

Ecological and Evolutionary Effects of Stickleback on Community Structure

PubMed Central

Des Roches, Simone; Shurin, Jonathan B.; Schluter, Dolph; Harmon, Luke J.

2013-01-01

Species’ ecology and evolution can have strong effects on communities. Both may change concurrently when species colonize a new ecosystem. We know little, however, about the combined effects of ecological and evolutionary change on community structure. We simultaneously examined the effects of top-predator ecology and evolution on freshwater community parameters using recently evolved generalist and specialist ecotypes of three-spine stickleback (Gasterosteus aculeatus). We used a mesocosm experiment to directly examine the effects of ecological (fish presence and density) and evolutionary (phenotypic diversity and specialization) factors on community structure at lower trophic levels. We evaluated zooplankton biomass and composition, periphyton and phytoplankton chlorophyll-a concentration, and net primary production among treatments containing different densities and diversities of stickleback. Our results showed that both ecological and evolutionary differences in the top-predator affect different aspects of community structure and composition. Community structure, specifically the abundance of organisms at each trophic level, was affected by stickleback presence and density, whereas composition of zooplankton was influenced by stickleback diversity and specialization. Primary productivity, in terms of chlorophyll-a concentration and net primary production was affected by ecological but not evolutionary factors. Our results stress the importance of concurrently evaluating both changes in density and phenotypic diversity on the structure and composition of communities. PMID:23573203

Changing abundance of Hexagenia mayfly nymphs in western Lake Erie of the Laurentian Great Lakes: Impediments to assessment of lake recovery?

USGS Publications Warehouse

Schloesser, D.W.; Nalepa, T.F.

2001-01-01

After an absence of 40 years, mayfly nymphs of the genus Hexagenia were found in sediments of western Lake Erie of the Laurentian Great Lakes in 1993 and, by 1997, were abundant enough to meet a mayfly-density management goal (ca. 350 nymphs m—2) based on pollution-abatement programs. We sampled nymphs in western Lake Erie and Lake St. Clair, located upstream of western Lake Erie, to determine the importance of seasonal abundance and life-history characteristics of nymphs (e.g., emergence and recruitment) on density estimates relative to the mayfly-density management goal. Two types of density patterns were observed: (1) densities were relatively high in spring and gradually decreased through late summer (observed in Lake Erie and Lake St. Clair in 1997 and Lake St. Clair in 1999) and (2) densities were relatively high in spring, gradually decreased to mid summer, abruptly decreased in mid summer, and then increased between summer and late fall (Lake Erie and Lake St. Clair in 1998 and Lake Erie in 1999). Length-frequency distributions of nymphs and observations of adults indicate that the primary cause for the two density patterns was attributed to failed (first pattern) and successful (second pattern) reproduction and emergence of nymphs into adults in mid summer. Gradual declines in densities were attributed to mortality of nymphs. Our results indicate that caution should be used when evaluating progress of pollution-abatement programs based on mayfly densities because recruitment success is variable both between and within years. Additionally, the interpretation of progress toward management goals, relative to the restoration of Hexagenia populations in the Great Lakes and possibly other water bodies throughout the world, is influenced by the number of years in which consequtive collections are made.

Optimization of a Widefield Structured Illumination Microscope for Non-Destructive Assessment and Quantification of Nuclear Features in Tumor Margins of a Primary Mouse Model of Sarcoma

PubMed Central

Fu, Henry L.; Mueller, Jenna L.; Javid, Melodi P.; Mito, Jeffrey K.; Kirsch, David G.; Ramanujam, Nimmi; Brown, J. Quincy

2013-01-01

Cancer is associated with specific cellular morphological changes, such as increased nuclear size and crowding from rapidly proliferating cells. In situ tissue imaging using fluorescent stains may be useful for intraoperative detection of residual cancer in surgical tumor margins. We developed a widefield fluorescence structured illumination microscope (SIM) system with a single-shot FOV of 2.1×1.6 mm (3.4 mm2) and sub-cellular resolution (4.4 µm). The objectives of this work were to measure the relationship between illumination pattern frequency and optical sectioning strength and signal-to-noise ratio in turbid (i.e. thick) samples for selection of the optimum frequency, and to determine feasibility for detecting residual cancer on tumor resection margins, using a genetically engineered primary mouse model of sarcoma. The SIM system was tested in tissue mimicking solid phantoms with various scattering levels to determine impact of both turbidity and illumination frequency on two SIM metrics, optical section thickness and modulation depth. To demonstrate preclinical feasibility, ex vivo 50 µm frozen sections and fresh intact thick tissue samples excised from a primary mouse model of sarcoma were stained with acridine orange, which stains cell nuclei, skeletal muscle, and collagenous stroma. The cell nuclei were segmented using a high-pass filter algorithm, which allowed quantification of nuclear density. The results showed that the optimal illumination frequency was 31.7 µm−1 used in conjunction with a 4×0.1 NA objective ( = 0.165). This yielded an optical section thickness of 128 µm and an 8.9×contrast enhancement over uniform illumination. We successfully demonstrated the ability to resolve cell nuclei in situ achieved via SIM, which allowed segmentation of nuclei from heterogeneous tissues in the presence of considerable background fluorescence. Specifically, we demonstrate that optical sectioning of fresh intact thick tissues performed equivalently in regards to nuclear density quantification, to physical frozen sectioning and standard microscopy. PMID:23894357

An evaluation of image quality and accuracy of eye bank measurement of donor cornea endothelial cell density in the Specular Microscopy Ancillary Study.

PubMed

Lass, Jonathan H; Gal, Robin L; Ruedy, Katrina J; Benetz, Beth Ann; Beck, Roy W; Baratz, Keith H; Holland, Edward J; Kalajian, Andrea; Kollman, Craig; Manning, Francis J; Mannis, Mark J; McCoy, Kristen; Montoya, Monty; Stulting, Doyle; Xing, Dongyuan

2005-03-01

The Specular Microscopy Ancillary Study was designed to examine donor corneal endothelial specular image quality, compare the central endothelial cell density determined by eye banks with the endothelial cell density determined by a central specular microscopy reading center, and evaluate donor factors that may have an impact on specular image quality and endothelial cell density accuracy. Nonrandomized comparative trial. Endothelial specular images of donor corneas assigned in the Cornea Donor Study. Certified readers assessed donor image quality (analyzable from fair to excellent vs. unanalyzable) and determined the central endothelial cell density. Independent adjudication was performed if there was a difference in the quality of grading or if the endothelial cell density varied by > or =5.0% between readers. Average reading center-determined endothelial cell density was compared with the endothelial cell density determined by each eye bank. Evaluation of image quality and accuracy of endothelial cell density. Of 688 donor endothelial images submitted by 23 eye banks, 663 (96%) were analyzable (excellent, 40 [6%]; good, 302 [44%]; fair, 321 [47%]), and 25 (4%) were unanalyzable by reading center standards. In situ retrieval and greater epithelial exposure correlated with a higher image quality grading. The eye bank-determined endothelial cell density of 434 of the 663 (65%) analyzable images were within 10% of the endothelial cell density determined by the reading center, whereas 185 (28%) were more than 10% higher and 44 (7%) were more than 10% lower. Greater variation in endothelial cell density between the eye banks and the reading center was observed with shorter time of death to preservation, presence of an epithelial defect, folds in Descemet's membrane, lower image quality, and the use of fixed-frame or center method endothelial cell density analysis. Overall, donor endothelial specular image quality and accuracy of endothelial cell density determination were good. However, the data suggest that factors that may affect image quality and contribute to variation in interpretation of the endothelial cell density should be addressed, because the donor endothelial cell density is an important parameter for assessing long-term corneal graft survival.

Prevalence of vitamin D deficiency and insufficiency in children with osteopenia or osteoporosis referred to a pediatric metabolic bone clinic.

PubMed

Bowden, Sasigarn A; Robinson, Renee F; Carr, Roxane; Mahan, John D

2008-06-01

The purpose of this work was to determine the prevalence of vitamin D deficiency and insufficiency in children with osteopenia or osteoporosis and to evaluate the relationship between serum 25-hydroxyvitamin D levels and bone parameters, including bone mineral density. Serum 25-hydroxyvitamin D, 1,25 dihydroxyvitamin D, parathyroid hormone, and other bone markers, as well as bone mineral density, were obtained for 85 pediatric patients with primary osteoporosis (caused by osteogenesis imperfecta or juvenile idiopathic osteoporosis) and secondary osteopenia or osteoporosis caused by various underlying chronic illnesses. Pearson's correlation was used to assess the relationship between vitamin D levels and different bone parameters. Vitamin D insufficiency (defined as serum 25-hydroxyvitamin D <30 ng/mL) was observed in 80.0% of patients. Overt vitamin D deficiency (defined as serum 25-hydroxyvitamin D <10 ng/mL) was present in 3.5% of patients. Using a more recent definition for vitamin D deficiency in adults (defined as serum 25-hydroxyvitamin D <20 ng/mL), 21.1% of the patients had vitamin D deficiency. There was a significant inverse correlation between 25-hydroxyvitamin D and parathyroid hormone levels. There was a positive correlation between 1,25 dihydroxyvitamin D and parathyroid hormone, alkaline phosphatase, and urine markers for bone turnover. Vitamin D insufficiency was remarkably common in pediatric patients with primary and secondary osteopenia or osteoporosis. The inverse relationship between 25-hydroxyvitamin D and parathyroid hormone levels suggests a physiologic impact of insufficient vitamin D levels that may contribute to low bone mass or worsen the primary bone disease. We suggest that monitoring and supplementation of vitamin D should be a priority in the management of pediatric patients with osteopenia or osteoporosis.

Biomimetic hydrogels gate transport of calcium ions across cell culture inserts.

PubMed

Kotanen, Christian N; Wilson, A Nolan; Wilson, Ann M; Ishihara, Kazuhiko; Guiseppi-Elie, Anthony

2012-06-01

Control of the in vitro spatiotemporal availability of calcium ions is one means by which the microenvironments of hematopoietic stem cells grown in culture may be reproduced. The effects of cross-linking density on the diffusivity of calcium ions through cell culture compatible poly(2-hydroxyethyl methacrylate) [poly(HEMA)]-based bioactive hydrogels possessing 1.0 mol% 2-methacryloyloxyethyl phosphorylcholine (MPC), 5 mol% N,N-(dimethylamino)ethylmethacrylate (DMAEMA) and ca. 17 mol% n-butyl acrylate (n-BA) have been investigated to determine if varying cross-link density is a viable approach to controlling transport of calcium across hydrogel membranes. Cross-linking density was varied by changing the composition of cross-linker, tetraethyleneglycol diacrylate (TEGDA). The hydrogel membranes were formed by sandwich casting onto the external surface of track-etched polycarbonate membranes (T = 10 μm, φ = 0.4 μm pores) of cell culture inserts, polymerized in place by UV light irradiation and immersed in buffered (0.025 HEPES, pH 7.4) 0.10 M calcium chloride solution. The transport of calcium ions across the hydrogel membrane was monitored using a calcium ion selective electrode set within the insert. Degree of hydration (21.6 ± 1.0%) and void fraction were found to be constant across all cross-linking densities. Diffusion coefficients, determined using time-lag analysis, were shown to be strongly dependent on and to exponentially decrease with increasing cross-linking density. Compared to that found in buffer (2.0-2.5 × 10⁻⁶ cm²/s), diffusion coefficients ranged from 1.40 × 10⁻⁶ cm²/s to 1.80 × 10⁻⁷ cm²/s and tortuosity values ranged from 1.7 to 10.0 for the 1 and 12 mol% TEGDA cross-linked hydrogels respectively. Changes in tortuosity arising from variations in cross-link density were found to be the primary modality for controlling diffusivity through novel n-BA containing poly(HEMA)-based bioactive hydrogels.

Ion thruster performance model

NASA Technical Reports Server (NTRS)

Brophy, J. R.

1984-01-01

A model of ion thruster performance is developed for high flux density, cusped magnetic field thruster designs. This model is formulated in terms of the average energy required to produce an ion in the discharge chamber plasma and the fraction of these ions that are extracted to form the beam. The direct loss of high energy (primary) electrons from the plasma to the anode is shown to have a major effect on thruster performance. The model provides simple algebraic equations enabling one to calculate the beam ion energy cost, the average discharge chamber plasma ion energy cost, the primary electron density, the primary-to-Maxwellian electron density ratio and the Maxwellian electron temperature. Experiments indicate that the model correctly predicts the variation in plasma ion energy cost for changes in propellant gas (Ar, Kr and Xe), grid transparency to neutral atoms, beam extraction area, discharge voltage, and discharge chamber wall temperature. The model and experiments indicate that thruster performance may be described in terms of only four thruster configuration dependent parameters and two operating parameters. The model also suggests that improved performance should be exhibited by thruster designs which extract a large fraction of the ions produced in the discharge chamber, which have good primary electron and neutral atom containment and which operate at high propellant flow rates.

Maximizing plant density affects broccoli yield and quality

USDA-ARS?s Scientific Manuscript database

Increased demand for fresh market bunch broccoli (Brassica oleracea L. var. italica) has led to increased production along the United States east coast. Maximizing broccoli yields is a primary concern for quickly expanding southeastern commercial markets. This broccoli plant density study was carr...

Asian patients with dyslipidemia in an urban population: Effect of ethnicity on their LDL-cholesterol treatment goals.

PubMed

Tan, Ngiap Chuan; Koh, Kim Hwee; Goh, Chin Chin; Koh, Yi Ling Eileen; Goh, Soo Chye Paul

2016-01-01

Dyslipidemia is the primary risk factor for arthrosclerosis. It is the most common chronic disease among the multiethnic Asian population in Singapore. Local national health survey has shown ethnic variability in achieving control of dyslipidemia. This study aimed to determine the proportion of patients in primary care, who achieved their low-density lipoprotein (LDL)-cholesterol treatment goals, stratified by the local major ethnic groups. It also evaluated the factors that affected their dyslipidemia control, including diet, exercise and medication usage. Research assistants administered questionnaires on adult patients with physician-diagnosed dyslipidemia to determine their views on diet, exercise, and medications in this cross-sectional study in 2 local primary care clinics. Their lipid profiles were retrieved from their laboratory reports in their electronic health records. Chi-square and Fisher exact tests were used for the categorical demographics and questionnaire variables, (P < .05: statistically significant). Logistic regression was performed using these significant variables to determine the adjusted odds of the ethnic groups. A total of 1093 eligible patients completed the questionnaires. The proportion of Chinese, Malay, and Indian patients who achieved LDL-cholesterol goals was 78.3%, 67.9%, and 68.5%, respectively. Among those who self-reported taking their favorite cholesterol-rich food occasionally when their cholesterol became controlled, 35.8% Indians failed to achieve treatment goals, compared to 20.1% Chinese and 30.9% Malay patients. Regular medication adherence was associated with 81.8% Chinese, 69.0% Malay, and 69.7% Indian reaching treatment goals. More Chinese met LDL-cholesterol treatment goals compared to Malays and Indians. Lipid-lowering medications enabled but smoking hindered their achievement of these treatment goals. Copyright © 2016 National Lipid Association. Published by Elsevier Inc. All rights reserved.

Inhibition of Vascular Endothelial Growth Factor Receptor Signal Transduction Blocks Follicle Progression but Does Not Necessarily Disrupt Vascular Development in Perinatal Rat Ovaries1

PubMed Central

McFee, Renee M.; Artac, Robin A.; McFee, Ryann M.; Clopton, Debra T.; Smith, Robyn A. Longfellow; Rozell, Timothy G.; Cupp, Andrea S.

2009-01-01

We hypothesized that vascular endothelial growth factor A (VEGFA) angiogenic isoforms and their receptors, FLT1 and KDR, regulate follicular progression in the perinatal rat ovary. Each VEGFA angiogenic isoform has unique functions (based on its exons) that affect diffusibility, cell migration, branching, and development of large vessels. The Vegfa angiogenic isoforms (Vegfa_120, Vegfa_164, and Vegfa_188) were detected in developing rat ovaries, and quantitative RT-PCR determined that Vegfa_120 and Vegfa_164 mRNA was more abundant after birth, while Vegfa_188 mRNA was highest at Embryonic Day 16. VEGFA and its receptors were localized to pregranulosa and granulosa cells of all follicle stages and to theca cells of advanced-stage follicles. To determine the role of VEGFA in developing ovaries, Postnatal Day 3/4 rat ovaries were cultured with 8 μM VEGFR-TKI, a tyrosine kinase inhibitor that blocks FLT1 and KDR. Ovaries treated with VEGFR-TKI had vascular development reduced by 94% (P < 0.0001), with more primordial follicles (stage 0), fewer early primary, transitional, and secondary follicles (stages 1, 3, and 4, respectively), and greater total follicle numbers compared with control ovaries (P < 0.005). V1, an inhibitor specific for KDR, was utilized to determine the effects of only KDR inhibition. Treatment with 30 μM V1 had no effect on vascular density; however, treated ovaries had fewer early primary, transitional, and secondary follicles and more primary follicles (stage 2) compared with control ovaries (P < 0.05). We conclude that VEGFA may be involved in primordial follicle activation and in follicle maturation and survival, which are regulated through vascular-dependent and vascular-independent mechanisms. PMID:19605787

Density determination of nail polishes and paint chips using magnetic levitation

NASA Astrophysics Data System (ADS)

Huang, Peggy P.

Trace evidence is often small, easily overlooked, and difficult to analyze. This study describes a nondestructive method to separate and accurately determine the density of trace evidence samples, specifically nail polish and paint chip using magnetic levitation (MagLev). By determining the levitation height of each sample in the MagLev device, the density of the sample is back extrapolated using a standard density bead linear regression line. The results show that MagLev distinguishes among eight clear nail polishes, including samples from the same manufacturer; separates select colored nail polishes from the same manufacturer; can determine the density range of household paint chips; and shows limited levitation for unknown paint chips. MagLev provides a simple, affordable, and nondestructive means of determining density. The addition of co-solutes to the paramagnetic solution to expand the density range may result in greater discriminatory power and separation and lead to further applications of this technique.

The relationship between dental implant stability and trabecular bone structure using cone-beam computed tomography

PubMed Central

2016-01-01

Purpose The objective of this study was to investigate the relationships between primary implant stability as measured by impact response frequency and the structural parameters of trabecular bone using cone-beam computed tomography(CBCT), excluding the effect of cortical bone thickness. Methods We measured the impact response of a dental implant placed into swine bone specimens composed of only trabecular bone without the cortical bone layer using an inductive sensor. The peak frequency of the impact response spectrum was determined as an implant stability criterion (SPF). The 3D microstructural parameters were calculated from CT images of the bone specimens obtained using both micro-CT and CBCT. Results SPF had significant positive correlations with trabecular bone structural parameters (BV/TV, BV, BS, BSD, Tb.Th, Tb.N, FD, and BS/BV) (P<0.01) while SPF demonstrated significant negative correlations with other microstructural parameters (Tb.Sp, Tb.Pf, and SMI) using micro-CT and CBCT (P<0.01). Conclusions There was an increase in implant stability prediction by combining BV/TV and SMI in the stepwise forward regression analysis. Bone with high volume density and low surface density shows high implant stability. Well-connected thick bone with small marrow spaces also shows high implant stability. The combination of bone density and architectural parameters measured using CBCT can predict the implant stability more accurately than the density alone in clinical diagnoses. PMID:27127692

Mass variation effect of teki grass (cyperus rotundus) composite against tensile strength and density

NASA Astrophysics Data System (ADS)

Rafiq Yanhar, Muhammad; Haris Nasution, A.

2018-05-01

The primary purpose of this study is to determine the tensile strength using ASTM D638 - 02a type IVB and density of teki grass (Cyperus rotundus) composite. The production process is carried out by mass variation of 2 gr, 3 gr, and 4 gr. Hand lay-up method with three repetitions is applied. Teki grass is chosen because it is easy to find and has some advantages biodegradable, harmless to health, available in large quantities, and cost-efficient. The test result showed the largest tensile strength is 21,61 MPa at 2-gram mass fiber. Fiber addition to 3 gram and 4-gram cause tensile strength decreases to 18,51 MPa and 11,65 MPa. It happens because the fibers are random and spread in all directions, so many fibers are undirectional with the tensile force. Beside that fibers addition made matrix volume reduced and a bond between fiber and matrix decreases, finally make fiber unable to hold the tensile force properly. It is recommended to use another type of ASTM D638 - 02a which has a larger narrow section like type I (13 mm) and type III (19mm) so specimens are not broken when removed from the mold, and there isn’t any decrease in tensile strength.Density test showed that fiber mass does not significantly affect the density.

Factors Underlying Bursting Behavior in a Network of Cultured Hippocampal Neurons Exposed to Zero Magnesium

PubMed Central

Mangan, Patrick S.; Kapur, Jaideep

2010-01-01

Factors contributing to reduced magnesium-induced neuronal action potential bursting were investigated in primary hippocampal cell culture at high and low culture density. In nominally zero external magnesium medium, pyramidal neurons from high-density cultures produced recurrent spontaneous action potential bursts superimposed on prolonged depolarizations. These bursts were partially attenuated by the NMDA receptor antagonist D-APV. Pharmacological analysis of miniature excitatory postsynaptic currents (EPSCs) revealed 2 components: one sensitive to D-APV and another to the AMPA receptor antagonist DNQX. The components were kinetically distinct. Participation of NMDA receptors in reduced magnesium-induced synaptic events was supported by the localization of the NR1 subunit of the NMDA receptor with the presynaptic vesicular protein synaptophysin. Presynaptically, zero magnesium induced a significant increase in EPSC frequency likely attributable to increased neuronal hyperexcitability induced by reduced membrane surface charge screening. Mean quantal content was significantly increased in zero magnesium. Cells from low-density cultures did not exhibit action potential bursting in zero magnesium but did show increased EPSC frequency. Low-density neurons had less synaptophysin immunofluorescence and fewer active synapses as determined by FM1-43 analysis. These results demonstrate that multiple factors are involved in network bursting. Increased probability of transmitter release presynaptically, enhanced NMDA receptor-mediated excitability postsynaptically, and extent of neuronal interconnectivity contribute to initiation and maintenance of elevated network excitability. PMID:14534286

Relating SMMR 37 GHz polarization difference to precipitation and atmospheric carbon dioxide concentration - A reappraisal

NASA Technical Reports Server (NTRS)

Tucker, C. J.

1992-01-01

The relations of Scanning Multi-channel Microwave Radiometer (SMMR) 37 GHz polarization difference to precipitation and atmospheric carbon dioxide (CO2) concentrations are reviewed. Annual precipitation data, a surrogate for green leaf vegetation density, are compared with the coincident SMMR 37 GHz polarization difference from arid and semi-arid West Africa for 1982-85. The SMMR 37 GHz polarization difference was found to be poorly correlated with precipitation in arid and semi-arid zones, contrary to previous reports. Coincident SMMR 37 GHz polarization difference and atmospheric CO2 concentration data from July 1981 to June 1983 are also reviewed. Previously suggested relations of the SMMR 37 GHz polarization difference to atmospheric CO2 concentrations were found to be heavily biased by winter conditions in the Northern Hemisphere. The use of the SMMR 37 GHz polarization difference for determining green leaf vegetation density, net primary production, atmospheric CO2 draw-down and related processes is questioned.

Shifts of community composition and population density substantially affect ecosystem function despite invariant richness.

PubMed

Spaak, Jurg W; Baert, Jan M; Baird, Donald J; Eisenhauer, Nico; Maltby, Lorraine; Pomati, Francesco; Radchuk, Viktoriia; Rohr, Jason R; Van den Brink, Paul J; De Laender, Frederik

2017-10-01

There has been considerable focus on the impacts of environmental change on ecosystem function arising from changes in species richness. However, environmental change may affect ecosystem function without affecting richness, most notably by affecting population densities and community composition. Using a theoretical model, we find that, despite invariant richness, (1) small environmental effects may already lead to a collapse of function; (2) competitive strength may be a less important determinant of ecosystem function change than the selectivity of the environmental change driver and (3) effects on ecosystem function increase when effects on composition are larger. We also present a complementary statistical analysis of 13 data sets of phytoplankton and periphyton communities exposed to chemical stressors and show that effects on primary production under invariant richness ranged from -75% to +10%. We conclude that environmental protection goals relying on measures of richness could underestimate ecological impacts of environmental change. © 2017 The Authors Ecology Letters published by CNRS and John Wiley & Sons Ltd.

Low frequency spectra of type III solar radio bursts

NASA Technical Reports Server (NTRS)

Weber, R. R.

1978-01-01

Flux density spectra have been determined for 91 simple type III solar bursts observed by the Goddard Space Flight Center radio astronomy experiment on the IMP-6 spacecraft during 1971 and 1972. Spectral peaks were found to occur at frequencies ranging from 44 kHz up to 2500 kHz. Half of the bursts peaked between 250 kHz and 900 kHz, corresponding to emission at solar distances of about 0.3 to 0.1 AU. Maximum burst flux density sometimes exceeds 10 to the -14th W/sq m/Hz. The primary factor controlling the spectral peak frequency of these bursts appears to be a variation in intrinsic power radiated by the source as the exciter moves outward from the sun, rather than radio propagation effects between the source and IMP-6. Thus, a burst spectrum strongly reflects the evolution of the properties of the exciting electron beam, and according to current theory, beam deceleration could help account for the observations.

Boomerang Satellites

NASA Astrophysics Data System (ADS)

Hesselbrock, Andrew; Minton, David A.

2017-10-01

We recently reported that the orbital architecture of the Martian environment allows for material in orbit around the planet to ``cycle'' between orbiting the planet as a ring, or as coherent satellites. Here we generalize our previous analysis to examine several factors that determine whether satellites accreting at the edge of planetary rings will cycle. In order for the orbiting material to cycle, tidal evolution must decrease the semi-major axis of any accreting satellites. In some systems, the density of the ring/satellite material, the surface mass density of the ring, the tidal parameters of the system, and the rotation rate of the primary body contribute to a competition between resonant ring torques and tidal dissipation that prevent this from occurring, either permanently or temporarily. Analyzing these criteria, we examine various bodies in our solar system (such as Saturn, Uranus, and Eris) to identify systems where cycling may occur. We find that a ring-satellite cycle may give rise to the current Uranian ring-satellite system, and suggest that Miranda may have formed from an early, more massive Uranian ring.

Prediction of occult lymph node metastasis in squamous cell carcinoma of the oral cavity and the oropharynx using peritumoral Prospero homeobox protein 1 lymphatic nuclear quantification.

PubMed

Mermod, Maxime; Bongiovanni, Massimo; Petrova, Tatiana V; Dubikovskaya, Elena A; Simon, Christian; Tolstonog, Genrich; Monnier, Yan

2016-09-01

The use of lymphatic vessel density as a predictor of occult lymph node metastasis (OLNM) in head and neck squamous cell carcinoma (HNSCC) has never been reported. Staining of the specific lymphatic endothelial cells nuclear marker, PROX1, as an indicator of lymphatic vessel density was determined by counting the number of positive cells in squamous cell carcinomas (SCCs) of the oral cavity and the oropharynx with clinically negative necks. Correlation with histopathological data was established. Peritumoral PROX1 lymphatic nuclear count significantly correlated with the detection of OLNM in multivariate analysis (p < .005). The sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of this parameter was 60%, 95%, 85%, and 90%, respectively. Peritumoral PROX1 lymphatic nuclear count in primary SCCs of the oral cavity and the oropharynx allows accurate prediction of occult lymph node metastasis. © 2016 Wiley Periodicals, Inc. Head Neck 38: 1407-1415, 2016. © 2016 Wiley Periodicals, Inc.

Characterization of Solidifiers used for Oil Spill Remediation ...

EPA Pesticide Factsheets

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial products were primarily comprised of organic polymers and a few trace elements. A natural sorbent, which was composed entirely of plant based matter, was also evaluated, and it had the highest oil removal capacity, but it did not produce a solid mat-like final product. Generally, solidifiers with a carbonate group, pore size greater than 5 µm, and bulk densities lower than 0.3 g cm-3 were found to have better efficiency and produced a cohesive rubbery final product that facilitated removal compared to sorbents. The importance of bulk density and pore size in the performance of the solidifier suggest that the primary mechanism of action was likely physical sorption. In this study, we focused on characterizing the 12 solidifiers by using different analytical techniques.

A review of studies on ion thruster beam and charge-exchange plasmas

NASA Technical Reports Server (NTRS)

Carruth, M. R., Jr.

1982-01-01

Various experimental and analytical studies of the primary beam and charge-exchange plasmas of ion thrusters are reviewed. The history of plasma beam research is recounted, emphasizing experiments on beam neutralization, expansion of the beam, and determination of beam parameters such as electron temperature, plasma density, and plasma potential. The development of modern electron bombardment ion thrusters is treated, detailing experimental results. Studies on charge-exchange plasma are discussed, showing results such as the relationship between neutralizer emission current and plasma beam potential, ion energies as a function of neutralizer bias, charge-exchange ion current collected by an axially moving Faraday cup-RPA for 8-cm and 30-cm ion thrusters, beam density and potential data from a 15-cm ion thruster, and charge-exchange ion flow around a 30-cm thruster. A 20-cm thruster electrical configuration is depicted and facility effects are discussed. Finally, plasma modeling is covered in detail for plasma beam and charge-exchange plasma.

Conventional multi-slice computed tomography (CT) and cone-beam CT (CBCT) for computer-assisted implant placement. Part I: relationship of radiographic gray density and implant stability.

PubMed

Arisan, Volkan; Karabuda, Zihni Cüneyt; Avsever, Hakan; Özdemir, Tayfun

2013-12-01

The relationship of conventional multi-slice computed tomography (CT)- and cone beam CT (CBCT)-based gray density values and the primary stability parameters of implants that were placed by stereolithographic surgical guides were analyzed in this study. Eighteen edentulous jaws were randomly scanned by a CT (CT group) or a CBCT scanner (CBCT group) and radiographic gray density was measured from the planned implants. A total of 108 implants were placed, and primary stability parameters were measured by insertion torque value (ITV) and resonance frequency analysis (RFA). Radiographic and subjective bone quality classification (BQC) was also classified. Results were analyzed by correlation tests and multiple regressions (p < .05). CBCT-based gray density values (765 ± 97.32 voxel value) outside the implants were significantly higher than those of CT-based values (668.4 ± 110 Hounsfield unit, p < .001). Significant relations were found among the gray density values outside the implants, ITV (adjusted r(2)  = 0.6142, p = .001 and adjusted r(2)  = 0.5166, p = .0021), and RFA (adjusted r(2)  = 0.5642, p = .0017 and adjusted r(2)  = 0.5423, p = .0031 for CT and CBCT groups, respectively). Data from radiographic and subjective BQC were also in agreement. Similar to the gray density values of CT, that of CBCT could also be predictive for the subjective BQC and primary implant stability. Results should be confirmed on different CBCT scanners. © 2012 Wiley Periodicals, Inc.

Silane coupling agent bearing a photoremovable succinimidyl carbonate for patterning amines on glass and silicon surfaces with controlled surface densities.

PubMed

Nakayama, Hidekazu; Nakanishi, Jun; Shimizu, Takahiro; Yoshino, Yutaro; Iwai, Hideo; Kaneko, Shingo; Horiike, Yasuhiro; Yamaguchi, Kazuo

2010-03-01

Patterned immobilization of synthetic and biological ligands on material surfaces with controlled surface densities is important for various bioanalytical and cell biological purposes. This paper describes the synthesis, characterization, and application of a novel silane coupling agent bearing a photoremovable succinimidyl carbonate, which enables the photopatterning of various primary amines on glass and silicon surfaces. The silane coupling agent is 1-[5-methoxy-2-nitro-4-(3-trimethoxysilylpropyloxy)phenyl]ethyl N-succinimidyl carbonate. The distinct feature of this molecule is that it has a photocleavable 2-nitrobenzyl switch between a trimethoxysilyl group and a succinimidyl carbonate, each reactive to the hydroxy groups of inorganic oxides and primary amines. Based on this molecular design, the compound allows for the one-step introduction of succinimidyl carbonates onto the surface of glass and silicon, immobilization of primary amines, and region-selective and dose-dependent release of the amines by near-UV irradiation. Therefore, we were able to pattern amine ligands on the substrates in given surface densities and arbitrary geometries by controlling the doses and regions of photoirradiation. These features were verified by UV-vis spectroscopy, contact angle measurements, infrared (IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), ellipsometry, and atomic force microscopy (AFM). The compound was applied to form a chemical density gradient of amino-biotin on a silicon substrate in a range of 0.87-0.12 chains/nm(2) by controlling photoirradiation under a standard fluorescence microscope. Furthermore, we also succeeded in forming a chemical density gradient at a lower surface density range (0.15-0.011 chains/nm(2)) on the substrate by diluting the feed amino-biotin with an inert control amine.

Prediction of supercritical ethane bulk solvent densities for pyrazine solvation shell average occupancy by 1, 2, 3, and 4 ethanes: combined experimental and ab initio approach.

PubMed

Hrnjez, Bruce J; Sultan, Samuel T; Natanov, Georgiy R; Kastner, David B; Rosman, Michael R

2005-11-17

We introduce a method that addresses the elusive local density at the solute in the highly compressible regime of a supercritical fluid. Experimentally, the red shift of the pyrazine n-pi electronic transition was measured at infinite dilution in supercritical ethane as a function of pressure from 0 to about 3000 psia at two temperatures, one close (35.0 degrees C) to the critical temperature and the other remote (55.0 degrees C). Computationally, stationary points were located on the potential surfaces for pyrazine and one, two, three, and four ethanes at the MP2/6-311++G(d,p) level. The vertical n-pi ((1)B(3u)) transition energies were computed for each of these geometries with a TDDFT/B3LYP/6-311++G(d,p) method. The combination of experiment and computation allows prediction of supercritical ethane bulk densities at which the pyrazine primary solvation shell contains an average of one, two, three, and four ethane molecules. These density predictions were achieved by graphical superposition of calculated shifts on the experimental shift versus density curves for 35.0 and 55.0 degrees C. Predicted densities are 0.0635, 0.0875, and 0.0915 g cm(-3) for average pyrazine primary solvation shell occupancy by one, two, and three ethanes at both 35.0 and 55.0 degrees C. Predicted densities are 0.129 and 0.150 g cm(-3) for occupancy by four ethanes at 35.0 and 55.0 degrees C, respectively. An alternative approach, designed to "average out" geometry specific shifts, is based on the relationship Deltanu = -23.9n cm(-1), where n = ethane number. Graphical treatment gives alternative predicted densities of 0.0490, 0.0844, and 0.120 g cm(-3) for average pyrazine primary solvation shell occupancy by one, two, and three ethanes at both 35.0 and 55.0 degrees C, and densities of 0.148 and 0.174 g cm(-3) for occupancy by four ethanes at 35.0 and 55.0 degrees C, respectively.

Role of host microenvironment in angiogenesis and microvascular functions in human breast cancer xenografts: mammary fat pad versus cranial tumors.

PubMed

Monsky, Wayne L; Mouta Carreira, Carla; Tsuzuki, Yoshikazu; Gohongi, Takeshi; Fukumura, Dai; Jain, Rakesh K

2002-04-01

The host microenvironment differs between primary and metastatic sites, affecting gene expression and various physiological functions. Here we show the differences in the physiological parameters between orthotopic primary and metastatic breast tumor xenografts using intravital microscopy and reveal the relationship between angiogenic gene expression and microvascular functions in vivo. ZR75-1, a human estrogen-dependent mammary carcinoma, was implanted into the mammary fat pad (primary site) of ovariectomized SCID female mice carrying estrogen pellets. The same tumor line was also grown in the cranial window (metastasis site). When tumors reached the diameter of 2.5 mm, angiogenesis, hemodynamics, and vascular permeability were measured by intravital microscopy, and expression of angiogenic growth factors was determined by quantitative reverse transcription-PCR. ZR75-1 tumors grown in the mammary fat pad had higher microvascular permeability but lower vascular density than the same tumors grown in the cranial window (2.5- and 0.7-fold, respectively). There was no significant difference in RBC velocity, vessel diameter, blood flow rate, and shear rate between two sites. The levels of vascular endothelial growth factor (VEGF), its receptors VEGFR1 and VEGFR2, and angiopoietin-1 mRNA tended to be higher in the mammary fat pad tumors than in the cranial tumors (1.5-, 1.5-, 3-, and 2-fold, respectively). The primary breast cancer exhibited higher vascular permeability, but the cranial tumor showed more angiogenesis, suggesting that the cranial environment is leakage resistant but proangiogenic. Collectively, host microenvironment is an important determinant of tumor gene expression and microvascular functions, and, thus, orthotopic breast tumor models should be useful for obtaining clinically relevant information.

Pulpal status of human primary teeth with physiological root resorption.

PubMed

Monteiro, Joana; Day, Peter; Duggal, Monty; Morgan, Claire; Rodd, Helen

2009-01-01

The overall aim of this study was to determine whether any changes occur in the pulpal structure of human primary teeth in association with physiological root resorption. The experimental material comprised 64 sound primary molars, obtained from children requiring routine dental extractions under general anaesthesia. Pulp sections were processed for indirect immunofluorescence using combinations of: (i) protein gene product 9.5 (a general neuronal marker); (ii) leucocyte common antigen CD45 (a general immune cell marker); and (iii) Ulex europaeus I lectin (a marker of vascular endothelium). Image analysis was then used to determine the percentage area of staining for each label within both the pulp horn and mid-coronal region. Following measurement of the greatest degree of root resorption in each sample, teeth were subdivided into three groups: those with physiological resorption involving less than one-third, one-third to two-thirds, and more than two-thirds of their root length. Wide variation was evident between different tooth samples with some resorbed teeth showing marked changes in pulpal histology. Decreased innervation density, increased immune cell accumulation, and increased vascularity were evident in some teeth with advanced root resorption. Analysis of pooled data, however, did not reveal any significant differences in mean percentage area of staining for any of these variables according to the three root resorption subgroups (P > 0.05, analysis of variance on transformed data). This investigation has revealed some changes in pulpal status of human primary teeth with physiological root resorption. These were not, however, as profound as one may have anticipated. It is therefore speculated that teeth could retain the potential for sensation, healing, and repair until advanced stages of root resorption.

Ecosystem Carbon Storage in Alpine Grassland on the Qinghai Plateau

PubMed Central

Liu, Shuli; Zhang, Fawei; Du, Yangong; Guo, Xiaowei; Lin, Li; Li, Yikang; Li, Qian; Cao, Guangmin

2016-01-01

The alpine grassland ecosystem can sequester a large quantity of carbon, yet its significance remains controversial owing to large uncertainties in the relative contributions of climate factors and grazing intensity. In this study we surveyed 115 sites to measure ecosystem carbon storage (both biomass and soil) in alpine grassland over the Qinghai Plateau during the peak growing season in 2011 and 2012. Our results revealed three key findings. (1) Total biomass carbon density ranged from 0.04 for alpine steppe to 2.80 kg C m-2 for alpine meadow. Median soil organic carbon (SOC) density was estimated to be 16.43 kg C m-2 in alpine grassland. Total ecosystem carbon density varied across sites and grassland types, from 1.95 to 28.56 kg C m-2. (2) Based on the median estimate, the total carbon storage of alpine grassland on the Qinghai Plateau was 5.14 Pg, of which 94% (4.85 Pg) was soil organic carbon. (3) Overall, we found that ecosystem carbon density was affected by both climate and grazing, but to different extents. Temperature and precipitation interaction significantly affected AGB carbon density in winter pasture, BGB carbon density in alpine meadow, and SOC density in alpine steppe. On the other hand, grazing intensity affected AGB carbon density in summer pasture, SOC density in alpine meadow and ecosystem carbon density in alpine grassland. Our results indicate that grazing intensity was the primary contributing factor controlling carbon storage at the sites tested and should be the primary consideration when accurately estimating the carbon storage in alpine grassland. PMID:27494253

Ecosystem Carbon Storage in Alpine Grassland on the Qinghai Plateau.

PubMed

Liu, Shuli; Zhang, Fawei; Du, Yangong; Guo, Xiaowei; Lin, Li; Li, Yikang; Li, Qian; Cao, Guangmin

2016-01-01

The alpine grassland ecosystem can sequester a large quantity of carbon, yet its significance remains controversial owing to large uncertainties in the relative contributions of climate factors and grazing intensity. In this study we surveyed 115 sites to measure ecosystem carbon storage (both biomass and soil) in alpine grassland over the Qinghai Plateau during the peak growing season in 2011 and 2012. Our results revealed three key findings. (1) Total biomass carbon density ranged from 0.04 for alpine steppe to 2.80 kg C m-2 for alpine meadow. Median soil organic carbon (SOC) density was estimated to be 16.43 kg C m-2 in alpine grassland. Total ecosystem carbon density varied across sites and grassland types, from 1.95 to 28.56 kg C m-2. (2) Based on the median estimate, the total carbon storage of alpine grassland on the Qinghai Plateau was 5.14 Pg, of which 94% (4.85 Pg) was soil organic carbon. (3) Overall, we found that ecosystem carbon density was affected by both climate and grazing, but to different extents. Temperature and precipitation interaction significantly affected AGB carbon density in winter pasture, BGB carbon density in alpine meadow, and SOC density in alpine steppe. On the other hand, grazing intensity affected AGB carbon density in summer pasture, SOC density in alpine meadow and ecosystem carbon density in alpine grassland. Our results indicate that grazing intensity was the primary contributing factor controlling carbon storage at the sites tested and should be the primary consideration when accurately estimating the carbon storage in alpine grassland.

Development Status of High-Thrust Density Electrostatic Engines

NASA Technical Reports Server (NTRS)

Patterson, Michael J.; Haag, Thomas W.; Foster, John E.; Young, Jason A.; Crofton, Mark W.

2017-01-01

Ion thruster technology offers the highest performance and efficiency of any mature electric propulsion thruster. It has by far the highest demonstrated total impulse of any technology option, demonstrated at input power levels appropriate for primary propulsion. It has also been successfully implemented for primary propulsion in both geocentric and heliocentric environments, with excellent ground/in-space correlation of both its performance and life. Based on these attributes there is compelling reasoning to continue the development of this technology: it is a leading candidate for high power applications; and it provides risk reduction for as-yet unproven alternatives. As such it is important that the operational limitations of ion thruster technology be critically examined and in particular for its application to primary propulsion its capabilities relative to thrust the density and thrust-to-power ratio be understood. This publication briefly addresses some of the considerations relative to achieving high thrust density and maximizing thrust-to-power ratio with ion thruster technology, and discusses the status of development work in this area being executed under a collaborative effort among NASA Glenn Research Center, the Aerospace Corporation, and the University of Michigan.

Surface modified CF x cathode material for ultrafast discharge and high energy density

DOE PAGES

Dai, Yang; Zhu, Yimei; Cai, Sendan; ...

2014-11-10

Li/CF x primary possesses the highest energy density of 2180 W h kg⁻¹ among all primary lithium batteries. However, a key limitation for the utility of this type of battery is in its poor rate capability because the cathode material, CF x, is an intrinsically poor electronic conductor. Here, we report on our development of a controlled process of surface de-fluorination under mild hydrothermal conditions to modify the highly fluorinated CF x. The modified CF x, consisting of an in situ generated shell component of F-graphene layers, possesses good electronic conductivity and removes the transporting barrier for lithium ions, yieldingmore » a high-capacity performance and an excellent rate-capability. Indeed, a capacity of 500 mA h g⁻¹ and a maximum power density of 44 800 W kg⁻¹ can be realized at the ultrafast rate of 30 C (24 A g⁻¹), which is over one order of magnitude higher than that of the state-of-the-art primary lithium-ion batteries.« less

Cortical inhibition and excitation by bilateral transcranial alternating current stimulation.

PubMed

Cancelli, Andrea; Cottone, Carlo; Zito, Giancarlo; Di Giorgio, Marina; Pasqualetti, Patrizio; Tecchio, Franca

2015-01-01

Transcranial electric stimulations (tES) with amplitude-modulated currents are promising tools to enhance neuromodulation effects. It is essential to select the correct cortical targets and inhibitory/excitatory protocols to reverse changes in specific networks. We aimed at assessing the dependence of cortical excitability changes on the current amplitude of 20 Hz transcranial alternating current stimulation (tACS) over the bilateral primary motor cortex. We chose two amplitude ranges of the stimulations, around 25 μA/cm2 and 63 μA/cm2 from peak to peak, with three values (at steps of about 2.5%) around each, to generate, respectively, inhibitory and excitatory effects of the primary motor cortex. We checked such changes online through transcranial magnetic stimulation (TMS)-induced motor evoked potentials (MEPs). Cortical excitability changes depended upon current density (p = 0.001). Low current densities decreased MEP amplitudes (inhibition) while high current densities increased them (excitation). tACS targeting bilateral homologous cortical areas can induce online inhibition or excitation as a function of the current density.

Investigation of the S(500) distribution for large air showers detected with the KASCADE-Grande array

NASA Astrophysics Data System (ADS)

Toma, G.; Apel, W. D.; Arteaga, J. C.; Badea, F.; Bekk, K.; Bertaina, M.; Blümer, J.; Bozdog, H.; Brancus, I. M.; Brüggemann, M.; Buchholz, P.; Cantoni, E.; Chiavassa, A.; Cossavella, F.; Daumiller, K.; de Souza, V.; di Pierro, F.; Doll, P.; Engel, R.; Engler, J.; Finger, M.; Fuhrmann, D.; Ghia, P. L.; Gils, H. J.; Glasstetter, R.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Huege, T.; Isar, P. G.; Kampert, K.-H.; Kang, D.; Kickelbick, D.; Klages, H. O.; Kolotaev, Y.; Łuczak, P.; Mathes, H. J.; Mayer, H. J.; Milke, J.; Mitrica, B.; Morello, C.; Navarra, G.; Nehls, S.; Oehlschläger, J.; Ostapchenko, S.; Over, S.; Petcu, M.; Pierog, T.; Rebel, H.; Roth, M.; Schieler, H.; Schröder, F.; Sima, O.; Stümpert, M.; Trinchero, G.; Ulrich, H.; Walkowiak, W.; Weindl, A.; Wochele, J.; Wommer, M.; Zabierowski, J.; KASCADE-Grande Collaboration

2009-12-01

Previous EAS investigations have shown that the charged particle density becomes independent of the primary mass at certain distances from the shower core and can be used as an estimator for the primary energy. In the context of the KASCADE-Grande experiment, the particular distance to shower core at which t his effect takes place is around 500 m, hence the study at this particular distance and the notation S(500) for the charged particle density. It has been shown that S(500) maps the primary energy. We present results of further investigations in this direction. An attenuation correction function can be derived from the S(500) attenuation with the EAS angle of incidence, allowing us to build an all event S(500) spectrum. In view of a future conversion of the recorded S(500) spectrum to the primary energy, based on simulations a calibration of the observed S(500) values with the primary energies has been worked out (in the energy range accessible to the KASCADE-Grande array, 10-10 eV).

Resonant Soft X-ray Scattering of Cellulose Microstructure in Plant Primary Cell Walls

NASA Astrophysics Data System (ADS)

Ye, Dan; Kiemle, Sarah N.; Wang, Cheng; Cosgrove, Daniel J.; Gomez, Esther W.; Gomez, Enrique D.

Cellulosic biomass is the most abundant raw material available for the production of renewable and sustainable biofuels. Breaking down cellulose is the rate-limiting step in economical biofuel production; therefore, a detailed understanding of the microscopic structure of plant cell walls is required to develop efficient biofuel conversion methods. Primary cell walls are key determinants of plant growth and mechanics. Their structure is complex and heterogeneous, making it difficult to elucidate how various components such as pectin, hemicellulose, and cellulose contribute to the overall structure. The electron density of these wall components is similar; such that conventional hard X-ray scattering does not generate enough contrast to resolve the different elements of the polysaccharide network. The chemical specificity of resonant soft X-ray scattering allows contrast to be generated based on differences in chemistry of the different polysaccharides. By varying incident X-ray energies, we have achieved increased scattering contrast between cellulose and other polysaccharides from primary cell walls of onions. By performing scattering at certain energies, features of the network structure of the cell wall are resolved. From the soft X-ray scattering results, we obtained the packing distance of cellulose microfibrils embedded in the polysaccharide network.

Extraction of conformal data in critical quantum spin chains using the Koo-Saleur formula

NASA Astrophysics Data System (ADS)

Milsted, Ashley; Vidal, Guifre

2017-12-01

We study the emergence of two-dimensional conformal symmetry in critical quantum spin chains on the finite circle. Our goal is to characterize the conformal field theory (CFT) describing the universality class of the corresponding quantum phase transition. As a means to this end, we propose and demonstrate automated procedures which, using only the lattice Hamiltonian H =∑jhj as an input, systematically identify the low-energy eigenstates corresponding to Virasoro primary and quasiprimary operators, and assign the remaining low-energy eigenstates to conformal towers. The energies and momenta of the primary operator states are needed to determine the primary operator scaling dimensions and conformal spins, an essential part of the conformal data that specifies the CFT. Our techniques use the action, on the low-energy eigenstates of H , of the Fourier modes Hn of the Hamiltonian density hj. The Hn were introduced as lattice representations of the Virasoro generators by Koo and Saleur [Nucl. Phys. B 426, 459 (1994), 10.1016/0550-3213(94)90018-3]. In this paper, we demonstrate that these operators can be used to extract conformal data in a nonintegrable quantum spin chain.

Primary experimental results of wire-array Z-pinches on PTS

NASA Astrophysics Data System (ADS)

Huang, X. B.; Zhou, S. T.; Ren, X. D.; Dan, J. K.; Wang, K. L.; Zhang, S. Q.; Li, J.; Xu, Q.; Cai, H. C.; Duan, S. C.; Ouyang, K.; Chen, G. H.; Ji, C.; Wang, M.; Feng, S. P.; Yang, L. B.; Xie, W. P.; Deng, J. J.

2014-12-01

The Primary Test Stand (PTS) developed at the China Academy of Engineering Physics is a multiterawatt pulsed power driver, which can deliver a ˜10 MA, 70 ns rise-time (10%-90%) current to a short circuit load and has important applications in Z-pinch driven inertial confinement fusion and high energy density physics. In this paper, primary results of tungsten wire-array Z-pinch experiments on PTS are presented. The load geometries investigated include 15-mm-tall cylindrical single and nested arrays with diameter ranging from 14.4-26.4 mm, and consisting of 132˜276 tungsten wires with 5˜10 μm in diameter. Multiple diagnostics were fielded to determine the characteristics of x-ray radiations and to obtain self-emitting images of imploding plasmas. X-ray power up to 80 TW with ˜3 ns FWMH is achieved by using nested wire arrays. The total x-ray energy exceeds 500 kJ and the peak radiation temperature is about 150 eV. Typical velocity of imploding plasmas goes around 3˜5×107 cm/s and the radial convergence ratio is between 10 and 20.

Accurate classical short-range forces for the study of collision cascades in Fe–Ni–Cr

DOE PAGES

Béland, Laurent Karim; Tamm, Artur; Mu, Sai; ...

2017-05-10

The predictive power of a classical molecular dynamics simulation is largely determined by the physical validity of its underlying empirical potential. In the case of high-energy collision cascades, it was recently shown that correctly modeling interactions at short distances is necessary to accurately predict primary damage production. An ab initio based framework is introduced for modifying an existing embedded-atom method FeNiCr potential to handle these short-range interactions. Density functional theory is used to calculate the energetics of two atoms approaching each other, embedded in the alloy, and to calculate the equation of state of the alloy as it is compressed.more » The pairwise terms and the embedding terms of the potential are modi ed in accordance with the ab initio results. Using this reparametrized potential, collision cascades are performed in Ni 50Fe 50, Ni 80Cr 20 and Ni 33Fe 33Cr 33. The simulations reveal that alloying Ni and NiCr to Fe reduces primary damage production, in agreement with some previous calculations. Alloying Ni and NiFe to Cr does not reduce primary damage production, in contradiction with previous calculations.« less

Diagnostic ability of peripapillary vessel density measurements of optical coherence tomography angiography in primary open-angle and angle-closure glaucoma.

PubMed

Rao, Harsha L; Kadambi, Sujatha V; Weinreb, Robert N; Puttaiah, Narendra K; Pradhan, Zia S; Rao, Dhanaraj A S; Kumar, Rajesh S; Webers, Carroll A B; Shetty, Rohit

2017-08-01

To evaluate the diagnostic ability of peripapillary vessel density measurements on optical coherence tomography angiography (OCTA) in primary open-angle glaucoma (POAG) and primary angle-closure glaucoma (PACG), and to compare these with peripapillary retinal nerve fibre layer (RNFL) thickness measurements. In a cross-sectional study, 48 eyes of 33 healthy control subjects, 63 eyes of 39 patients with POAG and 49 eyes of 32 patients with PACG underwent OCTA (RTVue-XR, Optovue, Fremont, California, USA) and RNFL imaging with spectral domain OCT. Diagnostic abilities of vessel density and RNFL parameters were evaluated using area under receiver operating characteristic curves (AUC) and sensitivities at fixed specificities. AUCs of peripapillary vessel density ranged between 0.48 for the temporal sector and 0.88 for the inferotemporal sector in POAG. The same in PACG ranged between 0.57 and 0.86. Sensitivities at 95% specificity ranged from 13% to 70% in POAG, and from 10% to 67% in PACG. AUCs of peripapillary RNFL thickness ranged between 0.51 for the temporal sector and 0.91 for the inferonasal sector in POAG. The same in PACG ranged between 0.61 and 0.87. Sensitivities at 95% specificity ranged from 8% to 68% in POAG, and from 2% to 67% in PACG. AUCs of all peripapillary vessel density measurements were comparable (p>0.05) to the corresponding RNFL thickness measurements in both POAG and PACG. Diagnostic ability of peripapillary vessel density parameters of OCTA, especially the inferotemporal sector measurement, was good in POAG and PACG. Diagnostic abilities of vessel density measurements were comparable to RNFL measurements in both POAG and PACG. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Structures-propulsion interactions and requirements. [large space structures

NASA Technical Reports Server (NTRS)

Coyner, J. V.

1982-01-01

The effects of low-thrust primary propulsion system characteristics on the mass, area, and orbit transfer characteristics of large space systems (LSS) were determined. Three general structural classes of LSS were considered, each with a broad range of diameters and nonstructural surface densities. While transferring the deployed structure from LEO and to GEO, an acceleration range of 0.02 to 0.1 g's was found to maximize deliverable payload based on structural mass impact. After propulsion system parametric analyses considering four propellant combinations produced values for available payload mass, length and volume, a thrust level range which maximizes deliverable LSS diameter was determined corresponding to a structure and propulsion vehicle. The engine start and/or shutdown thrust transients on the last orbit transfer (apogee) burn can impose transient loads which would be greater than the steady-state loads at the burnout acceleration. The effect of the engine thrust transients on the LSS was determined from the dynamic models upon which various engine ramps were imposed.

Change in bone mineral density and its determinants in pre- and perimenopausal Chinese women: the Hong Kong Perimenopausal Women Osteoporosis Study.

PubMed

Ho, S C; Chan, S G; Yip, Y B; Chan, C S Y; Woo, J L F; Sham, A

2008-12-01

This 30-month study investigating bone change and its determinants in 438 perimenopausal Chinese women revealed that the fastest bone loss occurred in women undergoing menopausal transition but maintenance of body weight and physical fitness were beneficial for bone health. Soy protein intake also seemed to exert a protective effect. This 30-month follow-up study aims to investigate change in bone mineral density and its determinants in Hong Kong Chinese perimenopausal women. Four hundred and thirty-eight women aged 45 to 55 years were recruited through random telephone dialing and primary care clinic. Bone mass, body composition, lifestyle measurements were obtained at baseline and at 9-, 18- and 30-month follow-ups. Univariate and stepwise multiple regression analyses were performed with the regression coefficients of BMD/C (derived from baseline and follow-up measurements) as the outcome variables. Menopausal status was classified as pre- or postmenopausal or transitional. Menopausal status was the strongest determinant of bone changes. An annual bone loss of about 0.5% was observed among premenopausal, 2% to 2.5% among transitional, and about 1.5% in postmenopausal women. Multiple regression analyses, revealed that a positive regression slope of body weight was protective for follow-up bone loss at all sites. Number of pregnancy, soy protein intake and walking were protective for total body BMC. Higher baseline LM was also protective for neck of femur BMD. Maintenance of body weight and physical fitness were observed to have a protective effect on for bone loss in Chinese perimenopausal women.

Ionospheric tomography using Faraday rotation of Automatic Dependent Surveillance Broadcast (UHF) signals Ionospheric Measurement From ADS-B Signals

NASA Astrophysics Data System (ADS)

Cushley, Alex Clay

The proposed launch of a CubeSat carrying the first space-borne ADS-B receiver by RMCC will create a unique opportunity to study the modification of radio waves following propagation through the ionosphere as the signals propagate from the transmitting aircraft to the passive satellite receiver(s). Experimental work is described which successfully demonstrated that ADS-B data can be used to reconstruct two-dimensional electron density maps of the ionosphere using techniques from computerized tomography. Ray-tracing techniques are used to determine the characteristics of individual waves, including the wave path and the state of polarization at the satellite receiver. The modelled Faraday rotation is determined and converted to TEC along the ray-paths. The resulting TEC is used as input for CIT using ART. This study concentrated on meso-scale structures 100--1000 km in horizontal extent. The primary scientific interest of this thesis was to show the feasibility of a new method to image the ionosphere and obtain a better understanding of magneto-ionic wave propagation. Keywords: Automatic Dependent Surveillance-Broadcast (ADS-B), Faraday rotation, electromagnetic (EM) waves, radio frequency (RF) propagation, ionosphere (auroral, irregularities, instruments and techniques), electron density profile, total electron content (TEC), computer ionospheric tomography (CIT), algebraic reconstruction technique (ART).

High density of tryptase-positive mast cells in human colorectal cancer: a poor prognostic factor related to protease-activated receptor 2 expression

PubMed Central

Malfettone, Andrea; Silvestris, Nicola; Saponaro, Concetta; Ranieri, Girolamo; Russo, Antonio; Caruso, Stefano; Popescu, Ondina; Simone, Giovanni; Paradiso, Angelo; Mangia, Anita

2013-01-01

Tryptase(+) mast cells (MCs), abundant in the invasive front of tumours, contribute to tissue remodelling. Indeed, protease-activated receptor-2 (PAR-2) activation by MC-tryptase is considered an oncogenic event in colorectal cancer (CRC). Recently, we have suggested NHERF1 as a potential new marker in CRC. In this study, we aimed to determine the distribution of tryptase(+) MCs and PAR-2 and to examine the relationship between PAR-2 and NHERF1, investigating their reputed usefulness as tumour markers. We studied a cohort of 115 CRC specimens including primary cancer (C) and adjacent normal mucosa (NM) by immunohistochemical double staining, analyzing the protein expression of MC-tryptase, PAR-2 and cytoplasmic NHERF1. MC density was higher in NM than in C. Tumours with high TNM stage and poor grade showed the highest MC density. A higher PAR-2 immunoreactivity characterized tumours most infiltrated by MCs compared with samples with low MC density. Furthermore, PAR-2 overexpression was associated with advanced TNM stage, poor grade and lymphovascular invasion (LVI). A positive correlation existed between tryptase(+) MC density and PAR-2 expression. Cytoplasmic NHERF1 was higher in C than in NM and overexpressing tumours resulted associated with nodal and distant metastases, poor grade and LVI. PAR-2 correlated with cytoplasmic NHERF1 and the PAR-2(+)/cytoplasmic NHERF1(+) expression immunophenotype identified tumours associated with unfavourable prognosis and aggressive clinical parameters. Our data indicate that the high density of tryptase(+) MCs at invasive margins of tumours was associated with advanced stages of CRC and was strongly correlated with PAR-2 expression. PMID:23991686

Nickel has biochemical, physiological, and structural effects on the green microalga Ankistrodesmus falcatus: An integrative study.

PubMed

Martínez-Ruiz, Erika Berenice; Martínez-Jerónimo, Fernando

2015-12-01

In recent years, the release of chemical pollutants to water bodies has increased due to anthropogenic activities. Ni(2+) is an essential metal that causes damage to aquatic biota at high concentrations. Phytoplankton are photosynthesizing microscopic organisms that constitute a fundamental community in aquatic environments because they are primary producers that sustain the aquatic food web. Nickel toxicity has not been characterized in all of the affected levels of biological organization. For this reason, the present study evaluated the toxic effects of nickel on the growth of a primary producer, the green microalga Ankistrodesmus falcatus, and on its biochemical, enzymatic, and structural levels. The IC50 (96h) was determined for Ni(2+). Based on this result, five concentrations were determined for additional tests, in which cell density was evaluated daily. At the end of the assay, pigments and six biomarkers, including antioxidant enzymes (catalase [CAT], glutathione peroxidase [GPx], superoxide dismutase [SOD]), and macromolecules (proteins, carbohydrates and lipids), were quantified; the integrated biomarker response (IBR) was determined also. The microalgae were observed by SEM and TEM. Population growth was affected starting at 7.5 μg L(-1) (0.028 μM), and at 120 μg L(-1) (0.450 μM), growth was inhibited completely; the determined IC50 was 17 μg L(-1). Exposure to nickel reduced the concentration of pigments, decreased the content of all of the macromolecules, inhibited of SOD activity, and increased CAT and GPx activities. The IBR revealed that Ni(2+) increased the antioxidant response and diminished the macromolecules concentration. A. falcatus was affected by nickel at very low concentrations; negative effects were observed at the macromolecular, enzymatic, cytoplasmic, and morphological levels, as well as in population growth. Ni(2+) toxicity could result in environmental impacts with consequences on the entire aquatic community. Current regulations should be revised to protect primary producers. Copyright © 2015 Elsevier B.V. All rights reserved.

Thermochemical properties for isooctane and carbon radicals: computational study.

PubMed

Snitsiriwat, Suarwee; Bozzelli, Joseph W

2013-01-17

Thermochemical properties for isooctane, its internal rotation conformers, and radicals with corresponding bond energies are determined by use of computational chemistry. Enthalpies of formation are determined using isodesmic reactions with B3LYP density function theory and composite CBS-QB3 methods. Application of group additivity with comparison to calculated values is illustrated. Entropy and heat capacities are determined using geometric parameters, internal rotor potentials, and frequencies from B3LYP/6-31G(d,p) calculations for the lowest energy conformer. Internal rotor potentials are determined for the isooctane parent and for the primary, secondary, and tertiary radicals in order to identify isomer energies. Intramolecular interactions are shown to have a significant effect on the enthalpy of formation of the isooctane parent and its radicals. The computed standard enthalpy of formation for the lowest energy conformers of isooctane from this study is -54.40 ± 1.60 kcal mol(-1), which is 0.8 kcal mol(-1) lower than the evaluated experimental value -53.54 ± 0.36 kcal mol(-1). The standard enthalpy of formation for the primary radical for a methyl on the quaternary carbon is -5.00 ± 1.69 kcal mol(-1), for the primary radical on the tertiary carbon is -5.18 ± 1.69 kcal mol(-1), for the secondary isooctane radical is -9.03 ± 1.84 kcal mol(-1), and for the tertiary isooctane radical is -12.30 ± 2.02 kcal mol(-1). Bond energy values for the isooctane radicals are 100.64 ± 1.73, 100.46 ± 1.73, 96.41 ± 1.88 and 93.14 ± 2.05 kcal mol(-1) for C3•CCCC2, C3CCCC2•, C3CC•CC2, and C3CCC•C2, respectively. Entropy and heat capacity values are reported for the lowest energy homologues.

The effect of altitude, patch size and disturbance on species richness and density of lianas in montane forest patches

NASA Astrophysics Data System (ADS)

Mohandass, Dharmalingam; Campbell, Mason J.; Hughes, Alice C.; Mammides, Christos; Davidar, Priya

2017-08-01

The species richness and density of lianas (woody vines) in tropical forests is determined by various abiotic and biotic factors. Factors such as altitude, forest patch size and the degree of forest disturbance are known to exert strong influences on liana species richness and density. We investigated how liana species richness and density were concurrently influenced by altitude (1700-2360 m), forest patch size, forest patch location (edge or interior) and disturbance intensity in the tropical montane evergreen forests, of the Nilgiri and Palni hills, Western Ghats, southern India. All woody lianas (≥1 cm dbh) were enumerated in plots of 30 × 30 m in small, medium and large forest patches, which were located along an altitudinal gradient ranging from 1700 to 2360 m. A total of 1980 individual lianas were recorded, belonging to 45 species, 32 genera and 21 families, from a total sampling area of 13.86 ha (across 154 plots). Liana species richness and density decreased significantly with increasing altitude and increased with increasing forest patch size. Within forest patches, the proportion of forest edge or interior habitat influenced liana distribution and succession especially when compared across the patch size categories. Liana species richness and density also varied along the altitudinal gradient when examined using eco-physiological guilds (i.e. shade tolerance, dispersal mode and climbing mechanism). The species richness and density of lianas within these ecological guilds responded negatively to increasing altitude and positively to increasing patch size and additionally displayed differing sensitivities to forest disturbance. Importantly, the degree of forest disturbance significantly altered the relationship between liana species richness and density to increasing altitude and patches size, and as such is likely the primary influence on liana response to montane forest succession. Our findings suggest that managing forest disturbance in the examined montane forests would assist in conserving local liana diversity across the examined altitudinal range.

Analyzing forensic evidence based on density with magnetic levitation.

PubMed

Lockett, Matthew R; Mirica, Katherine A; Mace, Charles R; Blackledge, Robert D; Whitesides, George M

2013-01-01

This paper describes a method for determining the density of contact trace objects with magnetic levitation (MagLev). MagLev measurements accurately determine the density (± 0.0002 g/cm(3) ) of a diamagnetic object and are compatible with objects that are nonuniform in shape and size. The MagLev device (composed of two permanent magnets with like poles facing) and the method described provide a means of accurately determining the density of trace objects. This method is inexpensive, rapid, and verifiable and provides numerical values--independent of the specific apparatus or analyst--that correspond to the absolute density of the sample that may be entered into a searchable database. We discuss the feasibility of MagLev as a possible means of characterizing forensic-related evidence and demonstrate the ability of MagLev to (i) determine the density of samples of glitter and gunpowder, (ii) separate glitter particles of different densities, and (iii) determine the density of a glitter sample that was removed from a complex sample matrix. © 2012 American Academy of Forensic Sciences.

Barrier island community change: What controls it?

NASA Astrophysics Data System (ADS)

Dows, B.; Young, D.; Zinnert, J.

2014-12-01

Conversion from grassland to woody dominated communities has been observed globally. In recent decades, this pattern has been observed in coastal communities along the mid-Atlantic U.S. In coastal environments, a suite of biotic and abiotic factors interact as filters to determine plant community structure and distribution. Microclimatic conditions: soil and air temperature, soil moisture and salinity, and light attenuation under grass cover were measured across a grassland-woody encroachment gradient on a Virginia barrier island; to identify the primary factors that mediate this change. Woody establishment was associated with moderately dense (2200 shoots/m2) grass cover, but reduced at high (> 6200 shoots/ m2) and low (< 1250 shoots/ m2) densities. Moderately dense grass cover reduced light attenuation (82.50 % reduction) to sufficiently reduce soil temperature thereby limiting soil moisture evaporation. However, high grass density reduced light attenuation (98.7 % reduction) enough to inhibit establishment of woody species; whereas low grass density attenuated much less light (48.7 % reduction) which allowed for greater soil moisture evaporation. Soil salinity was dynamic as rainfall, tidal inundation, and sea spray produce spatiotemporal variation throughout the barrier island landscape. The importance of light and temperature were compounded as they also indirectly affect soil salinity via their affects on soil moisture. Determining how these biotic and abiotic factors relate to sea level rise and climate change will improve understanding coastal community response as global changes proceed. Understanding how community shifts affect ecosystem function and their potential to affect adjacent systems will also improve predictive ability of coastal ecosystem responses.

First observations of Mercury's plasma mantle by MESSENGER

NASA Astrophysics Data System (ADS)

DiBraccio, Gina A.; Slavin, James A.; Raines, Jim M.; Gershman, Daniel J.; Tracy, Patrick J.; Boardsen, Scott A.; Zurbuchen, Thomas H.; Anderson, Brian J.; Korth, Haje; McNutt, Ralph L.; Solomon, Sean C.

2015-11-01

We present the first observations of Mercury's plasma mantle, a primary region for solar wind entry into the planetary magnetosphere, located in the high-latitude magnetotail. MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) observations from two orbits on 10 November 2012 have been analyzed. The main plasma mantle features are (1) a steady decrease in proton density as MESSENGER moved deeper into the magnetotail; (2) frequent flux transfer events throughout the magnetosheath and into the magnetotail, suggesting that these events are the primary source for solar wind plasma injection; (3) a diamagnetic depression, due to the presence of plasma, as pressure balance is maintained; and (4) a clear proton velocity dispersion, resulting from lower-energy protons being transported deep into the magnetosphere as higher-energy protons escape downtail. From these velocity dispersions we infer cross-magnetosphere electric potentials of 23 kV and 29 kV, consistent with estimates determined from measurements of magnetopause reconnection rate and tail loading and unloading events.

Lateral and Time Distributions of Extensive Air Showers for CHICOS

NASA Astrophysics Data System (ADS)

Jillings, C. J.; Wells, D.; Chan, K. C.; Hill, J.; Falkowski, B.; Sepikas, J.

2005-04-01

We report results of a series of detailed Monte-Carlo calculations to determine the density and arrival-time distribution of charged particles in extensive air showers. We have parameterized both distributions as a function of distance from the shower axis, energy of the primary cosmic-ray proton, and incident zenith angle. Muons and electrons are parameterized separately. These parameterizations can be easily used in maximum-likelihood reconstruction of air showers. Calculations were performed for primary energies between 10^18 and 10^21eV and zenith angles out to approximately 50^o. The calculations are appropriate for the California High School Cosmic Ray Observatory: a 400 km^2 array of scintillation detectors in Los Angeles county. The average elevation of the array is approximately 250 meters above sea level. Currently 64 of 90 sites are operational. The array will be completed this year. We thank the NSF, the CURE program at the Jet Propulsion Laboratory, the SURF program at Caltech, and the Chinese University of Hong Kong.

Secondary Electron Emission Yields

NASA Technical Reports Server (NTRS)

Krainsky, I.; Lundin, W.; Gordon, W. L.; Hoffman, R. W.

1981-01-01

The secondary electron emission (SEE) characteristics for a variety of spacecraft materials were determined under UHV conditions using a commercial double pass CMA which permits sequential Auger electron electron spectroscopic analysis of the surface. The transparent conductive coating indium tin oxide (ITO) was examined on Kapton and borosilicate glass and indium oxide on FED Teflon. The total SEE coefficient ranges from 2.5 to 2.6 on as-received surfaces and from 1.5 to 1.6 on Ar(+) sputtered surfaces with 5 nm removed. A cylindrical sample carousel provides normal incidence of the primary beam as well as a multiple Faraday cup measurement of the approximately nA beam currents. Total and true secondary yields are obtained from target current measurements with biasing of the carousel. A primary beam pulsed mode to reduce electron beam dosage and minimize charging of insulating coatings was applied to Mg/F2 coated solar cell covers. Electron beam effects on ITO were found quite important at the current densities necessary to do Auger studies.

Influence of primary fragment excitation energy and spin distributions on fission observables

NASA Astrophysics Data System (ADS)

Litaize, Olivier; Thulliez, Loïc; Serot, Olivier; Chebboubi, Abdelaziz; Tamagno, Pierre

2018-03-01

Fission observables in the case of 252Cf(sf) are investigated by exploring several models involved in the excitation energy sharing and spin-parity assignment between primary fission fragments. In a first step the parameters used in the FIFRELIN Monte Carlo code "reference route" are presented: two parameters for the mass dependent temperature ratio law and two constant spin cut-off parameters for light and heavy fragment groups respectively. These parameters determine the initial fragment entry zone in excitation energy and spin-parity (E*, Jπ). They are chosen to reproduce the light and heavy average prompt neutron multiplicities. When these target observables are achieved all other fission observables can be predicted. We show here the influence of input parameters on the saw-tooth curve and we discuss the influence of a mass and energy-dependent spin cut-off model on gamma-rays related fission observables. The part of the model involving level densities, neutron transmission coefficients or photon strength functions remains unchanged.

Viability of primary osteoblasts after treatment with tenofovir alafenamide: Lack of cytotoxicity at clinically relevant drug concentrations

PubMed Central

Callebaut, Christian; Liu, Yang; Babusis, Darius; Ray, Adrian; Miller, Michael; Kitrinos, Kathryn

2017-01-01

Tenofovir alafenamide (TAF) is a phosphonoamidate prodrug of the nucleotide HIV reverse transcriptase inhibitor tenofovir (TFV). TAF is approved for the treatment of HIV-1 infection as part of the single-tablet regimen containing elvitegravir, cobicistat, emtricitabine, and TAF. When dosed once-daily, TAF results in approximately 90% lower levels of plasma TFV and a 4-fold increase in intracellular TFV-diphosphate (TFV-DP) in PBMCs compared with the TFV prodrug tenofovir disoproxil fumarate (TDF). Several antiretrovirals, including TDF, have been associated with bone mineral density decreases in patients; the effect of clinically relevant TAF concentrations on primary osteoblast viability was therefore assessed in vitro. Studies in PBMCs determined that a 2-hour TAF exposure at concentrations similar to human plasma Cmax achieved intracellular TFV-DP levels comparable to those observed after the maximum recommended human dose of 25 mg TAF. Comparable intracellular TFV-DP levels were achieved in primary osteoblasts with 2-hour TAF exposure daily for 3 days at concentrations similar to those used for PBMCs (100–400 nM). No change in cell viability was observed in either primary osteoblasts or PBMCs. The mean TAF CC50 in primary osteoblasts after 3 days of daily 2-hour pulses was >500 μM, which is >1033 times higher than the TAF maximum recommended human dose plasma Cmax. In summary, primary osteoblasts were not preferentially loaded by TAF compared with PBMCs, with comparable TFV-DP levels achieved in both cell types. Furthermore, there was no impact on osteoblast cell viability at clinically relevant TAF concentrations. PMID:28182625

Viability of primary osteoblasts after treatment with tenofovir alafenamide: Lack of cytotoxicity at clinically relevant drug concentrations.

PubMed

Callebaut, Christian; Liu, Yang; Babusis, Darius; Ray, Adrian; Miller, Michael; Kitrinos, Kathryn

2017-01-01

Tenofovir alafenamide (TAF) is a phosphonoamidate prodrug of the nucleotide HIV reverse transcriptase inhibitor tenofovir (TFV). TAF is approved for the treatment of HIV-1 infection as part of the single-tablet regimen containing elvitegravir, cobicistat, emtricitabine, and TAF. When dosed once-daily, TAF results in approximately 90% lower levels of plasma TFV and a 4-fold increase in intracellular TFV-diphosphate (TFV-DP) in PBMCs compared with the TFV prodrug tenofovir disoproxil fumarate (TDF). Several antiretrovirals, including TDF, have been associated with bone mineral density decreases in patients; the effect of clinically relevant TAF concentrations on primary osteoblast viability was therefore assessed in vitro. Studies in PBMCs determined that a 2-hour TAF exposure at concentrations similar to human plasma Cmax achieved intracellular TFV-DP levels comparable to those observed after the maximum recommended human dose of 25 mg TAF. Comparable intracellular TFV-DP levels were achieved in primary osteoblasts with 2-hour TAF exposure daily for 3 days at concentrations similar to those used for PBMCs (100-400 nM). No change in cell viability was observed in either primary osteoblasts or PBMCs. The mean TAF CC50 in primary osteoblasts after 3 days of daily 2-hour pulses was >500 μM, which is >1033 times higher than the TAF maximum recommended human dose plasma Cmax. In summary, primary osteoblasts were not preferentially loaded by TAF compared with PBMCs, with comparable TFV-DP levels achieved in both cell types. Furthermore, there was no impact on osteoblast cell viability at clinically relevant TAF concentrations.

Long-term primary culture of mouse mammary tumor cells: production of virus.

PubMed

Young, L J; Cardiff, R D; Ashley, R L

1975-05-01

Long-term primary cultures of mouse mammary tumor cells proved an excellent source of mouse mammary tumor virus (MMTV). Virus purified from these primary cultures had the same morphologic biochemical, immunologic, and biologic characteristics as MMTV. Quantitation of MMTV-protein equivalents released into the medium was measured by the radioimmunoassay for MMTV. Peak production levels were 20-40 mug MMTV protien equivalents/75-cm-2 flask/24 hours. These cultures produced MMTV for as long as 90 days. MMTV cultivation depended on the initial cell-plating density and hormones. Maximal MMTV release was obtained at a plating density of 1 times 10-6 cells/cm-2 in the presence of insulin and hydrocortisone. Insulin alone gave basal levels of MMTV, and hydrocortisone alone increased MMTV release only three-fold, but insulin and hydrocortisone together effected an eightfold increase in MMTV release. This suggested that hydrocortisone had a primary effect on MMTV release and insulin acted synergistically with hydrocortisone to maximize MMTV release.

Characteristics of dislocation structure in creep deformed lamellar tial alloy within primary regime

NASA Astrophysics Data System (ADS)

Cho, H. S.; Nam, Soo W.

1999-06-01

In this investigation, dislocations of a lamellar TiAl alloy are analyzed after creeping in the primary range at 800°C/200MPa in order to interpret their mobility It was found that the dislocation density in γ-laths decreased as the creep deformation proceeds within primary creep regime Schmid factor analysis suggests that the creep deformation in the early stage of the primary creep regime is controlled by the gliding of some of the initial dislocations which have a high enough Schmid factor As the creep deformation progressed, those dislocations with high Schmid factors slip preferentially to be annihilated at the α-γ interface For further continuous deformation, dislocation generation is required, and for this, α-phase is transformed to γ-phase in order to generate new dislocations A slow dislocation generation process by phase transformation of α-phase compared with the absorbing rate to sinks is responsible for the decreasing dislocation density as the creep strain increases

Compressor seal rub energetics study

NASA Technical Reports Server (NTRS)

Laverty, W. F.

1978-01-01

The rub mechanics of compressor abradable blade tip seals at simulated engine conditions were investigated. Twelve statistically planned, instrumented rub tests were conducted with titanium blades and Feltmetal fibermetal rubstrips. The tests were conducted with single stationary blades rubbing against seal material bonded to rotating test disks. The instantaneous rub torque, speed, incursion rate and blade temperatures were continuously measured and recorded. Basic rub parameters (incursion rate, rub depth, abradable density, blade thickness and rub velocity) were varied to determine the effects on rub energy and heat split between the blade, rubstrip surface and rub debris. The test data was reduced, energies were determined and statistical analyses were completed to determine the primary and interactive effects. Wear surface morphology, profile measurements and metallographic analysis were used to determine wear, glazing, melting and material transfer. The rub energies for these tests were most significantly affected by the incursion rate while rub velocity and blade thickness were of secondary importance. The ratios of blade wear to seal wear were representative of those experienced in engine operation of these seal system materials.

Metrics of Cellular and Vascular Infiltration of Human Acellular Dermal Matrix in Ventral Hernia Repairs

PubMed Central

Campbell, Kristin Turza; Burns, Nadja K.; Ensor, Joe; Butler, Charles E.

2012-01-01

Background Human acellular dermal matrix (HADM) is used for ventral hernia repair, as it resists infection and remodels via surrounding tissue. However, the tissue source and impact of basement membrane (BM) on cell and vessel infiltration have not been determined. We hypothesized that musculofascia would be the primary tissue source of cells and vessels infiltrating into HADM and the BM would inhibit infiltration. Methods Fifty-six guinea pigs underwent inlay HADM ventral hernia repair with the BM oriented toward or away from the peritoneum. At postoperative weeks 1, 2, or 4, repair sites were completely excised. Histologic and immunohistochemical analyses were performed to quantify cell and vessel density within repair-site zones, including interface (lateral, beneath musculofascia) and center (beneath subcutaneous fat) zones. Cell and vessel quantities were compared as functions of zone, BM orientation, and time. Results Cellular and vascular infiltration increased over time universally. The interface demonstrated greater mean cell density than the center (weeks 1 and 2, p=0.01, p<0.0001). Cell density was greater with the BM oriented toward the peritoneum at week 4 (p=0.02). The interface zone had greater mean vessel density than the center zone at week 4 (p<0.0001). Orienting the BM toward the peritoneum increased vessel density at week 4 (p=0.0004). Conclusion Cellular and vascular infiltration into HADM for ventral hernia repairs was greater from musculofascia than subcutaneous and the BM inhibited cellular and vascular. HADM should be placed adjacent to the best vascularizing tissue to improve fibrovascular incorporation. PMID:22456361

Salivary density of Streptococcus mutans and Streptococcus sobrinus and dental caries in children and adolescents with Down syndrome

PubMed Central

SCALIONI, Flávia; CARRADA, Camila; MACHADO, Fernanda; Karina, DEVITO; RIBEIRO, Luiz Cláudio; CESAR, Dionéia; RIBEIRO, Rosangela

2017-01-01

Abstract Streptococcus mutans and Streptococcus sobrinus are strongly associated with dental caries. However, the relationship between oral streptococci and dental caries in children with Down syndrome is not well characterized. Objective To assess and compare dental caries experience and salivary S. mutans, S. sobrinus, and streptococci counts between groups of Down syndrome and non-Down syndrome children and adolescents. Material and Methods This study included a sample of 30 Down syndrome children and adolescents (G-DS) and 30 age- and sex-matched non-Down syndrome subjects (G-ND). Dental caries experience was estimated by the number of decayed, missing, and filled teeth in the primary dentition and the permanent dentition. Unstimulated whole saliva samples were collected from all participants. The fluorescence in situ hybridization technique was used to identify the presence and counts of the bacteria. The statistical analysis included chi-square, Student’s t-test and Spearman’s correlation. Results The G-DS exhibited a significantly higher caries-free rate (p<0.001) and a lower S. mutans salivary density (p<0.001). No significant differences were found in the salivary densities of S. sobrinus or streptococci between the groups (p=0.09 and p=0.21, respectively). The salivary S. mutans or S. sobrinus densities were not associated with dental caries experience in neither group. Conclusion The reduced dental caries experience observed in this group of Down syndrome children and adolescents cannot be attributed to lower salivary S. mutans densities, as determined with the fluorescence in situ hybridization technique. PMID:28678943

Quartz resonator fluid density and viscosity monitor

DOEpatents

Martin, Stephen J.; Wiczer, James J.; Cernosek, Richard W.; Frye, Gregory C.; Gebert, Charles T.; Casaus, Leonard; Mitchell, Mary A.

1998-01-01

A pair of thickness-shear mode resonators, one smooth and one with a textured surface, allows fluid density and viscosity to be independently resolved. A textured surface, either randomly rough or regularly patterned, leads to trapping of liquid at the device surface. The synchronous motion of this trapped liquid with the oscillating device surface allows the device to weigh the liquid; this leads to an additional response that depends on liquid density. This additional response enables a pair of devices, one smooth and one textured, to independently resolve liquid density and viscosity; the difference in responses determines the density while the smooth device determines the density-viscosity product, and thus, the pair determines both density and viscosity.

Textured-surface quartz resonator fluid density and viscosity monitor

DOEpatents

Martin, Stephen J.; Wiczer, James J.; Cernosek, Richard W.; Frye, Gregory C.; Gebert, Charles T.; Casaus, Leonard; Mitchell, Mary A.

1998-08-25

A pair of thickness-shear mode resonators, one smooth and one with a textured surface, allows fluid density and viscosity to be independently resolved. A textured surface, either randomly rough or regularly patterned, leads to trapping of liquid at the device surface. The synchronous motion of this trapped liquid with the oscillating device surface allows the device to weigh the liquid; this leads to an additional response that depends on liquid density. This additional response enables a pair of devices, one smooth and one textured, to independently resolve liquid density and viscosity; the difference in responses determines the density while the smooth device determines the density-viscosity product, and thus, the pair determines both density and viscosity.

Energy transmission transformer for a wireless capsule endoscope: analysis of specific absorption rate and current density in biological tissue.

PubMed

Shiba, Kenji; Nagato, Tomohiro; Tsuji, Toshio; Koshiji, Kohji

2008-07-01

This paper reports on the electromagnetic influences on the analysis of biological tissue surrounding a prototype energy transmission system for a wireless capsule endoscope. Specific absorption rate (SAR) and current density were analyzed by electromagnetic simulator in a model consisting of primary coil and a human trunk including the skin, fat, muscle, small intestine, backbone, and blood. First, electric and magnetic strength in the same conditions as the analytical model were measured and compared to the analytical values to confirm the validity of the analysis. Then, SAR and current density as a function of frequency and output power were analyzed. The validity of the analysis was confirmed by comparing the analytical values with the measured ones. The SAR was below the basic restrictions of the International Commission on Nonionizing Radiation Protection (ICNIRP). At the same time, the results for current density show that the influence on biological tissue was lowest in the 300-400 kHz range, indicating that it was possible to transmit energy safely up to 160 mW. In addition, we confirmed that the current density has decreased by reducing the primary coil's current.

Increasing plant density in eastern United States broccoli production systems to maximize marketable head yields

USDA-ARS?s Scientific Manuscript database

Increased demand for fresh market broccoli (Brassica oleracea L. var. italica) has led to increased production along the eastern seaboard of the United States. Maximizing broccoli yields is a primary concern for quickly expanding eastern commercial markets. Thus, a plant density study was carried ...

Great Red Spot's detection with the Juno gravity experiment

NASA Astrophysics Data System (ADS)

Parisi, M.; Folkner, W. M.

2017-12-01

The Juno spacecraft entered orbit about Jupiter in July 2016. During the perijoves (or closest approaches to Jupiter), Juno carries out observations of the magnetosphere, atmosphere and gravity field of the planet. The gravity field is estimated from precise measurements of the Doppler shift of the Juno radio signal and provides information on the Jovian interior structure.In July 2017 the 7th Juno perijove was over the Great Red Spot. The primary goal was determining differences in ammonia and water abundance in the GRS using the Microwave Radiometer instrument, while Doppler data was acquired acquired on a secondary basis. We present results of analysis of the PJ7 Doppler data to constrain the mass density variations of the GRS relative to the global average. We also present analysis to determine whether future Juno data will provide stronger constraints on the structure of the GRS.

Degenerate stars and gravitational collapse in AdS/CFT

NASA Astrophysics Data System (ADS)

Arsiwalla, Xerxes; de Boer, Jan; Papadodimas, Kyriakos; Verlinde, Erik

2011-01-01

We construct composite CFT operators from a large number of fermionic primary fields corresponding to states that are holographically dual to a zero temperature Fermi gas in AdS space. We identify a large N regime in which the fermions behave as free particles. In the hydrodynamic limit the Fermi gas forms a degenerate star with a radius determined by the Fermi level, and a mass and angular momentum that exactly matches the boundary calculations. Next we consider an interacting regime, and calculate the effect of the gravitational back-reaction on the radius and the mass of the star using the Tolman-Oppenheimer-Volkoff equations. Ignoring other interactions, we determine the "Chandrasekhar limit" beyond which the degenerate star (presumably) undergoes gravitational collapse towards a black hole. This is interpreted on the boundary as a high density phase transition from a cold baryonic phase to a hot deconfined phase.

Cellular generators of the cortical auditory evoked potential initial component.

PubMed

Steinschneider, M; Tenke, C E; Schroeder, C E; Javitt, D C; Simpson, G V; Arezzo, J C; Vaughan, H G

1992-01-01

Cellular generators of the initial cortical auditory evoked potential (AEP) component were determined by analyzing laminar profiles of click-evoked AEPs, current source density, and multiple unit activity (MUA) in primary auditory cortex of awake monkeys. The initial AEP component is a surface-negative wave, N8, that peaks at 8-9 msec and inverts in polarity below lamina 4. N8 is generated by a lamina 4 current sink and a deeper current source. Simultaneous MUA is present from lower lamina 3 to the subjacent white matter. Findings indicate that thalamocortical afferents are a generator of N8 and support a role for lamina 4 stellate cells. Relationships to the human AEP are discussed.

LIVER REGENERATION STUDIES WITH RAT HEPATOCYTES IN PRIMARY CULTURE

EPA Science Inventory

Adult rat parenchymal hepatocytes in primary culture can be induced to enter into DNA synthesis and mitosis. The optimal conditions for hepatocyte replication are low plating density (less than 10,000 cells/sq cm) and 50% serum from two-thirds partially hepatectomized rats (48 hr...

Glycemic control among patients with type 2 diabetes at a primary health care center in Oman.

PubMed

Al Balushi, Khalid A; Al-Haddabi, Mahmod; Al-Zakwani, Ibrahim; Al Za'abi, Mohammed

2014-10-01

To determine the status of blood sugar control by using fasting blood sugar (FBS) of ≤6.1 mmol/l and glycosyted hemoglobin A1c (HbAc1) of <7% as indictors of glycemic control and to assess the influence of demographic, blood pressure (BP) and lipid characteristics on glycemic control. This retrospective study included all Omani patients with type 2 diabetes (N=177) attended a primary health care center in Al-Dakhiliya region, Oman. The overall mean age of the cohort was 53±12 years (range: 24-91) with females representing 60% (n=106) of the study sample. The study found that only 9.6% (n=17) and 35% (n=62) of the patients attained optimal FBS and HbAc1 levels, respectively. Higher HbA1c was significantly associated with higher diastolic BP (84 versus 80 mm Hg; p=0.006), higher total cholesterol (5.2 versus 4.7 mmol/l; p=0.002) and higher low-density lipoprotein cholesterol (3.8 versus 3.0 mmol/l; p=0.034). The results demonstrated poor glycemic control in Oman type 2 diabetic patients comparable to local and global studies especially in those hypertensive and dyslipidemic patients. Implementation of early and aggressive management of diabetes mellitus at the primary care setting is warranted. Copyright © 2014 Primary Care Diabetes Europe. Published by Elsevier Ltd. All rights reserved.

Microstructure and mineral composition of dental enamel of permanent and deciduous teeth.

PubMed

De Menezes Oliveira, Maria Angélica Hueb; Torres, Carolina Paes; Gomes-Silva, Jaciara Miranda; Chinelatti, Michelle Alexandra; De Menezes, Fernando Carlos Hueb; Palma-Dibb, Regina Guenka; Borsatto, Maria Cristina

2010-05-01

This study evaluated and compared in vitro the microstructure and mineral composition of permanent and deciduous teeth's dental enamel. Sound third molars (n = 12) and second primary molars (n = 12) were selected and randomly assigned to the following groups, according to the analysis method performed (n = 4): Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Energy dispersive X-ray spectrometer (EDS). Qualitative and quantitative comparisons of the dental enamel were done. The microscopic findings were analyzed statistically by a nonparametric test (Kruskal-Wallis). The measurements of the prisms number and thickness were done in SEM photomicrographs. The relative amounts of calcium (Ca) and phosphorus (P) were determined by EDS investigation. Chemical phases present in both types of teeth were observed by the XRD analysis. The mean thickness measurements observed in the deciduous teeth enamel was 1.14 mm and in the permanent teeth enamel was 2.58 mm. The mean rod head diameter in deciduous teeth was statistically similar to that of permanent teeth enamel, and a slightly decrease from the outer enamel surface to the region next to the enamel-dentine junction was assessed. The numerical density of enamel rods was higher in the deciduous teeth, mainly near EDJ, that showed statistically significant difference. The percentage of Ca and P was higher in the permanent teeth enamel. The primary enamel structure showed a lower level of Ca and P, thinner thickness and higher numerical density of rods. (c) 2009 Wiley-Liss, Inc.

Insulin resistance and its association with the components of the metabolic syndrome among obese children and adolescents.

PubMed

Juárez-López, Carlos; Klünder-Klünder, Miguel; Medina-Bravo, Patricia; Madrigal-Azcárate, Adrián; Mass-Díaz, Eliezer; Flores-Huerta, Samuel

2010-06-07

Insulin resistance is the primary metabolic disorder associated with obesity; yet little is known about its role as a determinant of the metabolic syndrome in obese children. The aim of this study is to assess the association between the degree of insulin resistance and the different components of the metabolic syndrome among obese children and adolescents. An analytical, cross-sectional and population-based study was performed in forty-four public primary schools in Campeche City, Mexico. A total of 466 obese children and adolescents between 11-13 years of age were recruited. Fasting glucose and insulin concentrations, high density lipoprotein cholesterol, triglycerides, waist circumference, systolic and diastolic blood pressures were measured; insulin resistance and metabolic syndrome were also evaluated. Out of the total population studied, 69% presented low values of high density lipoprotein cholesterol, 49% suffered from abdominal obesity, 29% had hypertriglyceridemia, 8% presented high systolic and 13% high diastolic blood pressure, 4% showed impaired fasting glucose, 51% presented insulin resistance and 20% metabolic syndrome. In spite of being obese, 13% of the investigated population did not present any metabolic disorder. For each one of the components of the metabolic syndrome, when insulin resistance increased so did odds ratios as cardiometabolic risk factors. Regardless of age and gender an increased degree of insulin resistance is associated with a higher prevalence of disorders in each of the components of the metabolic syndrome and with a heightened risk of suffering metabolic syndrome among obese children and adolescents.

Rationale and design of the dal-OUTCOMES trial: efficacy and safety of dalcetrapib in patients with recent acute coronary syndrome.

PubMed

Schwartz, Gregory G; Olsson, Anders G; Ballantyne, Christie M; Barter, Phillip J; Holme, Ingar M; Kallend, David; Leiter, Lawrence A; Leitersdorf, Eran; McMurray, John J V; Shah, Prediman K; Tardif, Jean-Claude; Chaitman, Bernard R; Duttlinger-Maddux, Regina; Mathieson, John

2009-12-01

Despite contemporary therapies for acute coronary syndrome (ACS), morbidity and mortality remain high. Low levels of high-density lipoprotein (HDL) cholesterol are common among patients with ACS and may contribute to ongoing risk. Strategies that raise levels of HDL cholesterol, such as inhibition of cholesterol ester transfer protein (CETP), might reduce risk after ACS. Dal-OUTCOMES is a multicenter, randomized, double-blind, placebo-controlled trial designed to test the hypothesis that CETP inhibition with dalcetrapib reduces cardiovascular morbidity and mortality in patients with recent ACS. The study will randomize approximately 15,600 patients to receive daily doses of dalcetrapib 600 mg or matching placebo, beginning 4 to 12 weeks after an index ACS event. There are no prespecified boundaries for HDL cholesterol levels at entry. Other elements of care, including management of low-density lipoprotein cholesterol, are to follow best evidence-based practice. The primary efficacy measure is time to first occurrence of coronary heart disease death, nonfatal acute myocardial infarction, unstable angina requiring hospital admission, resuscitated cardiac arrest, or atherothrombotic stroke. The trial will continue until 1,600 primary end point events have occurred, all evaluable subjects have been followed for at least 2 years, and 80% of evaluable subjects have been followed for at least 2.5 years. Dal-OUTCOMES will determine whether CETP inhibition with dalcetrapib, added to current evidence-based care, reduces cardiovascular morbidity and mortality after ACS.

Habitat suitability of Anopheles vector species and association with human malaria in the Atlantic Forest in south-eastern Brazil.

PubMed

Laporta, Gabriel Zorello; Ramos, Daniel Garkauskas; Ribeiro, Milton Cezar; Sallum, Maria Anice Mureb

2011-08-01

Every year, autochthonous cases of Plasmodium vivax malaria occur in low-endemicity areas of Vale do Ribeira in the south-eastern part of the Atlantic Forest, state of São Paulo, where Anopheles cruzii and Anopheles bellator are considered the primary vectors. However, other species in the subgenus Nyssorhynchus of Anopheles (e.g., Anopheles marajoara) are abundant and may participate in the dynamics of malarial transmission in that region. The objectives of the present study were to assess the spatial distribution of An. cruzii, An. bellator and An. marajoara and to associate the presence of these species with malaria cases in the municipalities of the Vale do Ribeira. Potential habitat suitability modelling was applied to determine both the spatial distribution of An. cruzii, An. bellator and An. marajoara and to establish the density of each species. Poisson regression was utilized to associate malaria cases with estimated vector densities. As a result, An. cruzii was correlated with the forested slopes of the Serra do Mar, An. bellator with the coastal plain and An. marajoara with the deforested areas. Moreover, both An. marajoara and An. cruzii were positively associated with malaria cases. Considering that An. marajoara was demonstrated to be a primary vector of human Plasmodium in the rural areas of the state of Amapá, more attention should be given to the species in the deforested areas of the Atlantic Forest, where it might be a secondary vector.

The Effect of Autologous Platelet Lysate Eye Drops: An In Vivo Confocal Microscopy Study

PubMed Central

Fea, Antonio M.; Testa, Valeria; Machetta, Federica; Parisi, Simone; D'Antico, Sergio; Spinetta, Roberta; Fusaro, Enrico; Grignolo, Federico M.

2016-01-01

Purpose. To determine the effectiveness of autologous platelet lysate (APL) eye drops in patients with primary Sjögren syndrome (SS) dry eye, refractory to standard therapy, in comparison with patients treated with artificial tears. We focused on the effect of APL on cornea morphology with the in vivo confocal microscopy (IVCM). Methods. Patients were assigned to two groups: group A used autologous platelet lysate QID, and group B used preservative-free artificial tears QID, for 90 days. Ophthalmological assessments included ocular surface disease index (OSDI), best corrected visual acuity (BCVA), Schirmer test, fluorescein score, and breakup time (BUT). A subgroup of patients in group A underwent IVCM: corneal basal epithelium, subbasal nerves, Langerhans cells, anterior stroma activated keratocytes, and reflectivity were evaluated. Results. 60 eyes of 30 patients were enrolled; in group A (n = 20 patients) mean OSDI, fluorescein score, and BUT showed significant improvement compared with group B (n = 10 patients). The IVCM showed a significant increase in basal epithelium cells density and subbasal nerve plexus density and number and a decrease in Langerhans cells density (p < 0.05). Conclusion. APL was found effective in the treatment of SS dry eye. IVCM seems to be a useful tool to visualize cornea morphologic modifications. PMID:27200376

The Effect of Autologous Platelet Lysate Eye Drops: An In Vivo Confocal Microscopy Study.

PubMed

Fea, Antonio M; Aragno, Vittoria; Testa, Valeria; Machetta, Federica; Parisi, Simone; D'Antico, Sergio; Spinetta, Roberta; Fusaro, Enrico; Grignolo, Federico M

2016-01-01

Purpose. To determine the effectiveness of autologous platelet lysate (APL) eye drops in patients with primary Sjögren syndrome (SS) dry eye, refractory to standard therapy, in comparison with patients treated with artificial tears. We focused on the effect of APL on cornea morphology with the in vivo confocal microscopy (IVCM). Methods. Patients were assigned to two groups: group A used autologous platelet lysate QID, and group B used preservative-free artificial tears QID, for 90 days. Ophthalmological assessments included ocular surface disease index (OSDI), best corrected visual acuity (BCVA), Schirmer test, fluorescein score, and breakup time (BUT). A subgroup of patients in group A underwent IVCM: corneal basal epithelium, subbasal nerves, Langerhans cells, anterior stroma activated keratocytes, and reflectivity were evaluated. Results. 60 eyes of 30 patients were enrolled; in group A (n = 20 patients) mean OSDI, fluorescein score, and BUT showed significant improvement compared with group B (n = 10 patients). The IVCM showed a significant increase in basal epithelium cells density and subbasal nerve plexus density and number and a decrease in Langerhans cells density (p < 0.05). Conclusion. APL was found effective in the treatment of SS dry eye. IVCM seems to be a useful tool to visualize cornea morphologic modifications.

Evidence for a Low Bulk Crustal Density for Mars from Gravity and Topography.

PubMed

Goossens, Sander; Sabaka, Terence J; Genova, Antonio; Mazarico, Erwan; Nicholas, Joseph B; Neumann, Gregory A

2017-08-16

Knowledge of the average density of the crust of a planet is important in determining its interior structure. The combination of high-resolution gravity and topography data has yielded a low density for the Moon's crust, yet for other terrestrial planets the resolution of the gravity field models has hampered reasonable estimates. By using well-chosen constraints derived from topography during gravity field model determination using satellite tracking data, we show that we can robustly and independently determine the average bulk crustal density directly from the tracking data, using the admittance between topography and imperfect gravity. We find a low average bulk crustal density for Mars, 2582 ± 209 kg m -3 . This bulk crustal density is lower than that assumed until now. Densities for volcanic complexes are higher, consistent with earlier estimates, implying large lateral variations in crustal density. In addition, we find indications that the crustal density increases with depth.

Computational Model Tracking Primary Electrons, Secondary Electrons, and Ions in the Discharge Chamber of an Ion Engine

NASA Technical Reports Server (NTRS)

Mahalingam, Sudhakar; Menart, James A.

2005-01-01

Computational modeling of the plasma located in the discharge chamber of an ion engine is an important activity so that the development and design of the next generation of ion engines may be enhanced. In this work a computational tool called XOOPIC is used to model the primary electrons, secondary electrons, and ions inside the discharge chamber. The details of this computational tool are discussed in this paper. Preliminary results from XOOPIC are presented. The results presented include particle number density distributions for the primary electrons, the secondary electrons, and the ions. In addition the total number of a particular particle in the discharge chamber as a function of time, electric potential maps and magnetic field maps are presented. A primary electron number density plot from PRIMA is given in this paper so that the results of XOOPIC can be compared to it. PRIMA is a computer code that the present investigators have used in much of their previous work that provides results that compare well to experimental results. PRIMA only models the primary electrons in the discharge chamber. Modeling ions and secondary electrons, as well as the primary electrons, will greatly increase our ability to predict different characteristics of the plasma discharge used in an ion engine.

Study on an azimuthal line cusp ion source for the KSTAR neutral beam injector.

PubMed

Jeong, Seung Ho; Chang, Doo-Hee; In, Sang Ryul; Lee, Kwang Won; Oh, Byung-Hoon; Yoon, Byung-Joo; Song, Woo Sob; Kim, Jinchoon; Kim, Tae Seong

2008-02-01

In this study it is found that the cusp magnetic field configuration of an anode bucket influences the primary electron behavior. An electron orbit code (ELEORBIT code) showed that an azimuthal line cusp (cusp lines run azimuthally with respect to the beam extraction direction) provides a longer primary electron confinement time than an axial line cusp configuration. Experimentally higher plasma densities were obtained under the same arc power when the azimuthal cusp chamber was used. The newly designed azimuthal cusp bucket has been investigated in an effort to increase the plasma density in its plasma generator per arc power.

High-Density Digital Data Storage System

NASA Technical Reports Server (NTRS)

Wright, Kenneth D.; Gray, David L.

1995-01-01

High-density digital data storage system designed for cost-effective storage of large amounts of information acquired during experiments. System accepts up to 20 channels of 16-bit digital data with overall transfer rates of 500 kilobytes per second. Data recorded on 8-millimeter magnetic tape in cartridges, each capable of holding up to five gigabytes of data. Each cartridge mounted on one of two tape drives. Operator chooses to use either or both of drives. One drive used for primary storage of data while other can be used to make a duplicate record of data. Alternatively, other drive serves as backup data-storage drive when primary one fails.

Diagnostic Value of Multidetector CT and Its Multiplanar Reformation, Volume Rendering and Virtual Bronchoscopy Postprocessing Techniques for Primary Trachea and Main Bronchus Tumors.

PubMed

Luo, Mingyue; Duan, Chaijie; Qiu, Jianping; Li, Wenru; Zhu, Dongyun; Cai, Wenli

2015-01-01

To evaluate the diagnostic value of multidetector CT (MDCT) and its multiplanar reformation (MPR), volume rendering (VR) and virtual bronchoscopy (VB) postprocessing techniques for primary trachea and main bronchus tumors. Detection results of 31 primary trachea and main bronchus tumors with MDCT and its MPR, VR and VB postprocessing techniques, were analyzed retrospectively with regard to tumor locations, tumor morphologies, extramural invasions of tumors, longitudinal involvements of tumors, morphologies and extents of luminal stenoses, distances between main bronchus tumors and trachea carinae, and internal features of tumors. The detection results were compared with that of surgery and pathology. Detection results with MDCT and its MPR, VR and VB were consistent with that of surgery and pathology, included tumor locations (tracheae, n = 19; right main bronchi, n = 6; left main bronchi, n = 6), tumor morphologies (endoluminal nodes with narrow bases, n = 2; endoluminal nodes with wide bases, n = 13; both intraluminal and extraluminal masses, n = 16), extramural invasions of tumors (brokethrough only serous membrane, n = 1; 4.0 mm-56.0 mm, n = 14; no clear border with right atelectasis, n = 1), longitudinal involvements of tumors (3.0 mm, n = 1; 5.0 mm-68.0 mm, n = 29; whole right main bronchus wall and trachea carina, n = 1), morphologies of luminal stenoses (irregular, n = 26; circular, n = 3; eccentric, n = 1; conical, n = 1) and extents (mild, n = 5; moderate, n = 7; severe, n = 19), distances between main bronchus tumors and trachea carinae (16.0 mm, n = 1; invaded trachea carina, n = 1; >20.0 mm, n = 10), and internal features of tumors (fairly homogeneous densities with rather obvious enhancements, n = 26; homogeneous density with obvious enhancement, n = 1; homogeneous density without obvious enhancement, n = 1; not enough homogeneous density with obvious enhancement, n = 1; punctate calcification with obvious enhancement, n = 1; low density without obvious enhancement, n = 1). MDCT and its MPR, VR and VB images have respective advantages and disadvantages. Their combination could complement to each other to accurately detect locations, natures (benignancy, malignancy or low malignancy), and quantities (extramural invasions, longitudinal involvements, extents of luminal stenoses, distances between main bronchus tumors and trachea carinae) of primary trachea and main bronchus tumors with crucial information for surgical treatment, are highly useful diagnostic methods for primary trachea and main bronchus tumors.

Low Bone Density

MedlinePlus

... Bone Density Exam/Testing › Low Bone Density Low Bone Density Low bone density is when your bone ... to people with normal bone density. Detecting Low Bone Density A bone density test will determine whether ...

Complex of vitamins and antioxidants protects low-density lipoproteins in blood plasma from free radical oxidation and activates antioxidants enzymes in erythrocytes from patients with coronary heart disease.

PubMed

Konovalova, G G; Lankin, V Z; Tikhaze, A K; Nezhdanova, I B; Lisina, M O; Kukharchuk, V V

2003-08-01

We studied the effect of a complex containing antioxidant vitamins C and E, provitamin A, and antioxidant element selenium on the contents of primary (lipid peroxides) and secondary products (malonic dialdehyde) of free radical lipid oxidation in low-density lipoproteins isolated from the plasma of patients with coronary heart disease and hypercholesterolemia by means of preparative ultracentrifugation. Activity of key antioxidant enzymes in the blood was measured during treatment with the antioxidant preparation. Combination treatment with antioxidant vitamins and antioxidant element selenium sharply decreased the contents of primary and secondary free radical oxidation products in circulating low-density lipoproteins and increased activity of antioxidant enzymes in erythrocytes. Activities of superoxide dismutase and selenium-containing glutathione peroxidase increased 1 and 2 months after the start of therapy, respectively.

Idaho Habitat Evaluation for Off-Site Mitigation Record : Annual Report 1988.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Idaho. Dept. of Fish and Game.

1990-03-01

The Idaho Department of Fish and Game (IDFG) has been monitoring and evaluating existing and proposed habitat improvement projects for steelhead and chinook in the Clearwater and Salmon subbasins since 1984. Projects included in the monitoring are funded by, or proposed for funding by, the Bonneville Power Administration (BPA) under the Northwest Power Planning Act as off-site mitigation for downstream hydropower development on the Snake and Columbia Rivers. This monitoring project is also funded under the same authority. A mitigation record is being developed to use actual and potential increases in smolt production as the best measures of benefit frommore » a habitat improvement project. This project is divided into two subprojects: general and intensive monitoring. Primary objectives of the general monitoring subproject are to determine natural production increases due to habitat improvement projects in terms of parr production and to determine natural production status and trends in Idaho. The second objective is accomplished by combining parr density from monitoring and evaluation of BPA habitat projects and from other IDFG management and research activities. The primary objective of the intensive monitoring subproject is to determine the relationships between spawning escapement, parr production, and smolt production in two Idaho streams; the upper Salmon River and Crooked River. Results of the intensive monitoring will be used to estimate mitigation benefits in terms of smolt production and to interpret natural production monitoring in Idaho. 30 refs., 19 figs., 34 tabs.« less

Effectiveness and feasibility of lowering playground density during recess to promote physical activity and decrease sedentary time at primary school.

PubMed

D'Haese, Sara; Van Dyck, Delfien; De Bourdeaudhuij, Ilse; Cardon, Greet

2013-12-10

This pilot study aimed at investigating the effectiveness of lowering playground density on increasing children's physical activity and decreasing sedentary time. Also the feasibility of this intervention was tested. Data were collected in September and October 2012 in three Belgian schools in 187, 9-12 year old children. During the intervention, playground density was decreased by splitting up recesses and decreasing the number of children sharing the playground. A within-subject design was used. Children wore accelerometers during the study week. Three-level (class - participant - measurement (baseline or intervention)) linear regression models were used to determine intervention effects. After the intervention week the school principals filled out a questionnaire concerning the feasibility of the intervention. The available play space was 12.18 ± 4.19 m²/child at baseline and increased to 24.24 ± 8.51 m²/child during intervention. During the intervention sedentary time decreased (-0.58 min/recess; -3.21%/recess) and moderate-to-vigorous physical activity (+1.04 min/recess; +5.9%/recess) increased during recess and during the entire school day (sedentary time: -3.29%/school day; moderate-to-vigorous physical activity +1.16%/school day). All principals agreed that children enjoyed the intervention; but some difficulties were reported. Lowering playground density can be an effective intervention for decreasing children's sedentary time and increasing their physical activity levels during recess; especially in least active children.

Magnetic-flutter-induced pedestal plasma transport

NASA Astrophysics Data System (ADS)

Callen, J. D.; Hegna, C. C.; Cole, A. J.

2013-11-01

Plasma toroidal rotation can limit reconnection of externally applied resonant magnetic perturbation (RMP) fields δB on rational magnetic flux surfaces. Hence it causes the induced radial perturbations δBρ to be small there, thereby inhibiting magnetic island formation and stochasticity at the top of pedestals in high (H-mode) confinement tokamak plasmas. However, the δBρs induced by RMPs increase away from rational surfaces and are shown to induce significant sinusoidal radial motion (flutter) of magnetic field lines with a radial extent that varies linearly with δBρ and inversely with distance from the rational surface because of the magnetic shear. This produces a radial electron thermal diffusivity that is (1/2)(δBρ/B0)2 times a kinetically derived, electron-collision-induced, magnetic-shear-reduced, effective parallel electron thermal diffusivity in the absence of magnetic stochasticity. These low collisionality flutter-induced transport processes and thin magnetic island effects are shown to be highly peaked in the vicinity of rational surfaces at the top of low collisionality pedestals. However, the smaller but finite level of magnetic-flutter-induced electron heat transport midway between rational surfaces is the primary factor that determines the electron temperature difference between rational surfaces at the pedestal top. The magnetic-flutter-induced non-ambipolar electron density transport can be large enough to push the plasma toward an electron density transport root. Requiring ambipolar density transport is shown to determine the radial electric field, the plasma toroidal rotation (via radial force balance), a reduced electron thermal diffusivity and increased ambipolar density transport in the pedestal. At high collisionality the various flutter effects are less strongly peaked at rational surfaces and generally less significant. They are thus less likely to exhibit flutter-induced resonant behaviour and transition toward an electron transport root. Magnetic-flutter-induced plasma transport processes provide a new paradigm for developing an understanding of how RMPs modify the pedestal structure to stabilize peeling-ballooning modes and thereby suppress edge localized modes in low collisionality tokamak H-mode plasmas.

Influence of genetic background, salinity, and inoculum size on growth of the ichthyotoxic golden alga (Prymnesium parvum).

PubMed

Rashel, Rakib H; Patiño, Reynaldo

2017-06-01

Salinity (5-30) effects on golden alga growth were determined at a standard laboratory temperature (22°C) and one associated with natural blooms (13°C). Inoculum-size effects were determined over a wide size range (100-100,000cellsml -1 ). A strain widely distributed in the USA, UTEX-2797 was the primary study subject but another of limited distribution, UTEX-995 was used to evaluate growth responses in relation to genetic background. Variables examined were exponential growth rate (r), maximum cell density (max-D) and, when inoculum size was held constant (100cellsml -1 ), density at onset of exponential growth (early-D). In UTEX-2797, max-D increased as salinity increased from 5 to ∼10-15 and declined thereafter regardless of temperature but r remained generally stable and only declined at salinity of 25-30. In addition, max-D correlated positively with r and early-D, the latter also being numerically highest at salinity of 15. In UTEX-995, max-D and r responded similarly to changes in salinity - they remained stable at salinity of 5-10 and 5-15, respectively, and declined at higher salinity. Also, max-D correlated with r but not early-D. Inoculum size positively and negatively influenced max-D and r, respectively, in both strains and these effects were significant even when the absolute size difference was small (100 versus 1000 cells ml -1 ). When cultured under similar conditions, UTEX-2797 grew faster and to much higher density than UTEX-995. In conclusion, (1) UTEX-2797's superior growth performance may explain its relatively wide distribution in the USA, (2) the biphasic growth response of UTEX-2797 to salinity variation, with peak abundance at salinity of 10-15, generally mirrors golden alga abundance-salinity associations in US inland waters, and (3) early cell density - whether artificially manipulated or naturally attained - can influence UTEX-2797 bloom potential. Published by Elsevier B.V.

Density-dependent vulnerability of forest ecosystems to drought

Treesearch

Alessandra Bottero; Anthony W. D' Amato; Brian J. Palik; John B. Bradford; Shawn Fraver; Mike A. Battaglia; Lance A. Asherin; Harald Bugmann

2017-01-01

Climate models predict increasing drought intensity and frequency for many regions, which may have negative consequences for tree recruitment, growth and mortality, as well as forest ecosystem services. Furthermore, practical strategies for minimizing vulnerability to drought are limited. Tree population density, a metric of tree abundance in a given area, is a primary...

Physical, spectral, and dynamical properties of asteroid (107) Camilla and its satellites

NASA Astrophysics Data System (ADS)

Pajuelo, M.; Carry, B.; Vachier, F.; Marsset, M.; Berthier, J.; Descamps, P.; Merline, W. J.; Tamblyn, P. M.; Grice, J.; Conrad, A.; Storrs, A.; Timerson, B.; Dunham, D.; Preston, S.; Vigan, A.; Yang, B.; Vernazza, P.; Fauvaud, S.; Bernasconi, L.; Romeuf, D.; Behrend, R.; Dumas, C.; Drummond, J. D.; Margot, J.-L.; Kervella, P.; Marchis, F.; Girard, J. H.

2018-07-01

The population of large 100+ km asteroids is thought to be primordial. As such, they are the most direct witnesses of the early history of our Solar System available. Those among them with satellites allow study of the mass, and hence density and internal structure. We study here the dynamical, physical, and spectral properties of the triple asteroid (107) Camilla from lightcurves, stellar occultations, optical spectroscopy, and high-contrast and high-angular-resolution images and spectro-images. Using 80 positions measured over 15 years, we determine the orbit of its larger satellite, S/2001 (107) 1, to be circular, equatorial, and prograde, with root-mean-square residuals of 7.8 mas, corresponding to a sub-pixel accuracy. From 11 positions spread over three epochs only, in 2015 and 2016, we determine a preliminary orbit for the second satellite S/2016 (107) 1. We find the orbit to be somewhat eccentric and slightly inclined to the primary's equatorial plane, reminiscent of the properties of inner satellites of other asteroid triple systems. Comparison of the near-infrared spectrum of the larger satellite reveals no significant difference with Camilla. Hence, both dynamical and surface properties argue for a formation of the satellites by excavation from impact and re-accumulation of ejecta in orbit. We determine the spin and 3-D shape of Camilla. The model fits well each data set: lightcurves, adaptive-optics images, and stellar occultations. We determine Camilla to be larger than reported from modeling of mid-infrared photometry, with a spherical-volume-equivalent diameter of 254 ± 36 km (3σuncertainty), in agreement with recent results from shape modeling (Hanus et al., 2017, A&A 601). Combining the mass of (1.12 ± 0.01) × 1019 kg (3σuncertainty) determined from the dynamics of the satellites and the volume from the 3-D shape model, we determine a density of 1,280 ± 130 kg · m-3 (3 σ uncertainty). From this density, and considering Camilla's spectral similarities with (24) Themis and (65) Cybele (for which water ice coating on surface grains was reported), we infer a silicate-to-ice mass ratio of 1-6, with a 10-30% macroporosity.

Method for determining transport critical current densities and flux penetration depth in bulk superconductors

NASA Technical Reports Server (NTRS)

Israelsson, Ulf E. (Inventor); Strayer, Donald M. (Inventor)

1992-01-01

A contact-less method for determining transport critical current density and flux penetration depth in bulk superconductor material. A compressor having a hollow interior and a plunger for selectively reducing the free space area for distribution of the magnetic flux therein are formed of superconductor material. Analytical relationships, based upon the critical state model, Maxwell's equations and geometrical relationships define transport critical current density and flux penetration depth in terms of the initial trapped magnetic flux density and the ratio between initial and final magnetic flux densities whereby data may be reliably determined by means of the simple test apparatus for evaluating the current density and flux penetration depth.

Stable regions around Exoplanets: the search for Exomoons

NASA Astrophysics Data System (ADS)

Fernandes Guimaraes, Ana Helena; Moretto Tusnski, Luis Ricardo; Vieira-Neto, Ernesto; Silva Valio, Adriana

2015-08-01

There are hundreds of exoplanets which the data are available to a dynamical investigation. We extracted from the data base (exoplanets.org) all planets and candidates which have the necessary data available for the numerical investigation of the orbital stability of a body around a exoplanet in a total of 2749 of those.There is a wealth diversity of exoplanets types and the expectation in find our Earth-living conditions in another planet motivates the search for extra-solar planets, and a satellite around a planet would, in addiction, help to keep a favorable climate.Using the planets class according to PHL@Arecibo, those planets were sorted out in groups. Analyses of density, distance from the primary body, and mass ratios were done beside the suggested classification to fit some no-classified planets into one of the groups.The aim of this work is to derive the upper stability limit (or upper critical orbit) of fictitious direct satellites around exoplanets of any density, or size, orbiting single stars. Our search is for stable regions around the planet, the called S-type orbits. This orbit type determines if there is any chance to exist (or not) bodies around the planets. The investigation is limited to single stars, excluding binaries.We derived such limit purely through numerical simulations. Our proposal involved long-term integration of the circular restricted three bodies problem . Basically, the cut off of the stability zone determined in the previous work by Domingos et al. (2006) were confirmed for any planet type. However, the limitation due the Roche limit of the own satellite showed to be lower. We used this to determined possible size and to adjust orbital range were a third body could orbit the exoplanet.Independently of densities, distance, and sizes of the objects involved, the idea was to delimit where to find celestial bodies in any given system around single stars. Furthermore, we aim to provide tracks to the search for exomoons using planetary transits.

Photopigment self-screening and the determination of macular pigment absorbance using heterochromatic flicker photometry.

PubMed

Smollon, William E; Wooten, Billy R; Hammond, Billy R

2015-11-01

Heterochromatic flicker photometry (HFP) is commonly used to determine macular pigment optical density (MPOD). Since HFP in this application is a locus comparison method, an identical relative spectral response at each locus is required for a perfect measure. We know this requirement cannot be strictly true since the optical density of photopigments increases as the foveal center is approached. Thus, the self-screening effect would result in an underestimate of MPOD. An earlier study concluded that the underestimate is on the order of 30%. We examined this issue by manipulating photopigment optical density, and consequently the degree of selfscreening. A continuously exposed, 470 nm, background bleached cone photopigments over a range from 0 to 80%. MPOD was determined 10' and 30' from the foveal center. Two subjects were used in the main experiment. Five additional subjects were studied with just the 0% and 80% bleach levels. Spectral measures were obtained at 0% and 70% bleach levels for the two primary subjects. Subjects in the main experiment showed MPOD estimates that increased with increasing bleaching. The effect, however, was small: one observer's MPOD increased 0.08 and 0.02 for the 10' and 30' loci, respectively; the other observer's values were 0.04 and 0.01 for the same loci. Comparable values were obtained for the other five subjects using the 0% and 80% bleach conditions. Spectral measures were consistent with the findings of the main experiment. When self-screening is nearly abolished (80% bleach), a relatively small underestimation is revealed for the unbleached state. For the 1° target we show about 2-3% underestimation. Our 20' target reveals a larger underestimate (8-9%), consistent with longer photoreceptor outer-segments nearer the foveal center. We conclude that HFP yields values essentially independent of self-screening for targets of 1° diameter or greater. Smaller targets are less than 10% underestimated for near-zero bleach conditions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Polyarene mediators for mediated redox flow battery

DOEpatents

Delnick, Frank M.; Ingersoll, David; Liang, Chengdu

2018-01-02

The fundamental charge storage mechanisms in a number of currently studied high energy redox couples are based on intercalation, conversion, or displacement reactions. With exception to certain metal-air chemistries, most often the active redox materials are stored physically in the electrochemical cell stack thereby lowering the practical gravimetric and volumetric energy density as a tradeoff to achieve reasonable power density. In a general embodiment, a mediated redox flow battery includes a series of secondary organic molecules that form highly reduced anionic radicals as reaction mediator pairs for the reduction and oxidation of primary high capacity redox species ex situ from the electrochemical cell stack. Arenes are reduced to stable anionic radicals that in turn reduce a primary anode to the charged state. The primary anode is then discharged using a second lower potential (more positive) arene. Compatible separators and solvents are also disclosed herein.

Impacts of land use and population density on seasonal surface water quality using a modified geographically weighted regression.

PubMed

Chen, Qiang; Mei, Kun; Dahlgren, Randy A; Wang, Ting; Gong, Jian; Zhang, Minghua

2016-12-01

As an important regulator of pollutants in overland flow and interflow, land use has become an essential research component for determining the relationships between surface water quality and pollution sources. This study investigated the use of ordinary least squares (OLS) and geographically weighted regression (GWR) models to identify the impact of land use and population density on surface water quality in the Wen-Rui Tang River watershed of eastern China. A manual variable excluding-selecting method was explored to resolve multicollinearity issues. Standard regression coefficient analysis coupled with cluster analysis was introduced to determine which variable had the greatest influence on water quality. Results showed that: (1) Impact of land use on water quality varied with spatial and seasonal scales. Both positive and negative effects for certain land-use indicators were found in different subcatchments. (2) Urban land was the dominant factor influencing N, P and chemical oxygen demand (COD) in highly urbanized regions, but the relationship was weak as the pollutants were mainly from point sources. Agricultural land was the primary factor influencing N and P in suburban and rural areas; the relationship was strong as the pollutants were mainly from agricultural surface runoff. Subcatchments located in suburban areas were identified with urban land as the primary influencing factor during the wet season while agricultural land was identified as a more prevalent influencing factor during the dry season. (3) Adjusted R 2 values in OLS models using the manual variable excluding-selecting method averaged 14.3% higher than using stepwise multiple linear regressions. However, the corresponding GWR models had adjusted R 2 ~59.2% higher than the optimal OLS models, confirming that GWR models demonstrated better prediction accuracy. Based on our findings, water resource protection policies should consider site-specific land-use conditions within each watershed to optimize mitigation strategies for contrasting land-use characteristics and seasonal variations. Copyright © 2016 Elsevier B.V. All rights reserved.

Multisensor sampling of pelagic ecosystem variables in a coastal environment to estimate zooplankton grazing impact

NASA Astrophysics Data System (ADS)

Sutton, Tracey; Hopkins, Thomas; Remsen, Andrew; Burghart, Scott

2001-01-01

Sampling was conducted on the west Florida continental shelf ecosystem modeling site to estimate zooplankton grazing impact on primary production. Samples were collected with the high-resolution sampler, a towed array bearing electronic and optical sensors operating in tandem with a paired net/bottle verification system. A close biological-physical coupling was observed, with three main plankton communities: 1. a high-density inshore community dominated by larvaceans coincident with a salinity gradient; 2. a low-density offshore community dominated by small calanoid copepods coincident with the warm mixed layer; and 3. a high-density offshore community dominated by small poecilostomatoid and cyclopoid copepods and ostracods coincident with cooler, sub-pycnocline oceanic water. Both high-density communities were associated with relatively turbid water. Applying available grazing rates from the literature to our abundance data, grazing pressure mirrored the above bio-physical pattern, with the offshore sub-pycnocline community contributing ˜65% of grazing pressure despite representing only 19% of the total volume of the transect. This suggests that grazing pressure is highly localized, emphasizing the importance of high-resolution sampling to better understand plankton dynamics. A comparison of our grazing rate estimates with primary production estimates suggests that mesozooplankton do not control the fate of phytoplankton over much of the area studied (<5% grazing of daily primary production), but "hot spots" (˜25-50% grazing) do occur which may have an effect on floral composition.

Field test results--a new logging tool for formation density and lithology measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borai, A.M.; Muhsin, M.A.

1983-03-01

The formation porosity can be determined from borehole density measurements if the density of the rock is known. Generally, this is determined from the lithology. The Litho-Density Tool, LDT, provides an improved measurement of the formation density and a new measurement of lithology. Field tests of LDT proved that the tool could be run alone in a wide range of formations to provide porosity values comparable to those obtained by running a density log combined with a neutron log.

Ecosystem development on terraces along the Kugururok River, northwest Alaska

USGS Publications Warehouse

Binkley, Dan; Suarez, F.; Stottlemyer, R.; Caldwell, B.

1997-01-01

Riverside terraces along the Kugururok River in the Noatak National Preserve provided an opportunity to study primary succession, considering general trends that apply across all terraces, and unique events that influence individual terraces. The 30-year-old willow/poplar (Salix spp., Populus balsamifera L.) terrace had no trees taller than 1.5 m; the abundant spruce trees were not tall enough to emerge from the canopy height of the willows and poplars, and moose (Alces alces [Clinton]) browsing limited the canopy height of these plants. The 75-year-old poplar/spruce (Picea glauca [Moench] Voss) terrace had a high density of poplars (> 1000/ha) and low density of spruce (125/ha); heavy browsing by moose reduced the density of poplar by about one-half. The removal of the poplar by moose in this stand resulted in sustained increases in growth of individual spruce trees. The 100-year-old younger spruce/poplar terrace had about twice as many spruce trees (1250/ha) as poplar trees (500/ha), and the spruce trees were larger on average than the poplar trees. In the 220+ year-old older spruce/poplar type, only a few poplars remained (about 25/ha), and the number of spruce trees (600/ha) was only half that of the younger stage, either from lower initial spruce density on this terrace, or increased mortality of spruce. The 240+ year-old spruce type was a second-generation forest, characterized by a high density (1950/ha) of small spruce trees, some of which were tilted, indicating discontinuous permafrost. Plant litterfall mass showed no strong trend with terrace age, although N content of litterfall appeared to decline by about 1/3 in the spruce-dominated stages. Fungal biomass increased with ecosystem age, whereas bacterial biomass and microfauna declined. We found no evidence of declining soil N supply in older stages, but fertilization experiments would be needed to determine if N limitation of productivity changed with ecosystem development. We conclude that the general successional trend of increased spruce dominance is robust for this location, but that unique events play important roles in determining tree densities and the timing of the shift in dominance from poplar to spruce. The arrival of moose in the 1970s accelerated dominance by spruce on young terraces.

Time-resolved SAXS study of the effect of a double hydrophilic block-copolymer on the formation of CaCO3 from a supersaturated salt solution.

PubMed

Bolze, J; Pontoni, D; Ballauff, M; Narayanan, T; Cölfen, H

2004-09-01

The effect of a double hydrophilic block-copolymer additive (made of polyaspartic acid and polyethyleneglycol, pAsp(10)-b-PEG(110)) on the initial formation of calcium carbonate from a supersaturated salt solution has been studied in situ by means of time-resolved synchrotron small-angle X-ray scattering (SAXS). A stopped-flow cell was used for rapidly mixing the 20 mM aqueous reactant solutions of calcium chloride and sodium carbonate. In reference measurements without polymer additive the very rapid formation of primary, overall spherical CaCO(3) particles with a radius of ca. 19 nm and a size polydispersity of ca. 26% was observed within the first 10 ms after mixing. A subsequent, very rapid aggregation of these primary particles was evidenced by a distinct upturn of the SAXS intensity at smallest angles. During the aggregation process the size of the primary particles remained unchanged. From an analysis of the absolute scattering intensity the mass density of these particles was determined to 1.9 g/cm(3). From this rather low density it is concluded that those precursor particles are amorphous, which has been confirmed by simultaneous wide-angle X-ray diffraction measurements. Upon adding 200 pm of the block-copolymer no influence on the size, the size polydispersity and morphology of the primary particles, nor on the kinetics of their formation and growth, was found. On the other hand, the subsequent aggregation and precipitation process is considerably slowed down by the additive and smaller aggregates result. The crystalline morphology of the sediment was studied in situ by WAXS ca. 50 min after mixing the reactants. Several diffraction rings could be detected, which indicate that a transformation of the metastable, amorphous precursor particles to randomly oriented vaterite nanocrystallites has taken place. In addition, a few isolated Bragg spots of high intensity were detected, which are attributed to individual, oriented calcite microcrystals that nucleated at the wall of the capillary.

Disentangling trophic relationships in a High Arctic tundra ecosystem through food web modeling.

PubMed

Legagneux, P; Gauthier, G; Berteaux, D; Bêty, J; Cadieux, M C; Bilodeau, F; Bolduc, E; McKinnon, L; Tarroux, A; Therrien, J F; Morissette, L; Krebs, C J

2012-07-01

Determining the manner in which food webs will respond to environmental changes is difficult because the relative importance of top-down vs. bottom-up forces in controlling ecosystems is still debated. This is especially true in the Arctic tundra where, despite relatively simple food webs, it is still unclear which forces dominate in this ecosystem. Our primary goal was to assess the extent to which a tundra food web was dominated by plant-herbivore or predator-prey interactions. Based on a 17-year (1993-2009) study of terrestrial wildlife on Bylot Island, Nunavut, Canada, we developed trophic mass balance models to address this question. Snow Geese were the dominant herbivores in this ecosystem, followed by two sympatric lemming species (brown and collared lemmings). Arctic foxes, weasels, and several species of birds of prey were the dominant predators. Results of our trophic models encompassing 19 functional groups showed that <10% of the annual primary production was consumed by herbivores in most years despite the presence of a large Snow Goose colony, but that 20-100% of the annual herbivore production was consumed by predators. The impact of herbivores on vegetation has also weakened over time, probably due to an increase in primary production. The impact of predators was highest on lemmings, intermediate on passerines, and lowest on geese and shorebirds, but it varied with lemming abundance. Predation of collared lemmings exceeded production in most years and may explain why this species remained at low density. In contrast, the predation rate on brown lemmings varied with prey density and may have contributed to the high-amplitude, periodic fluctuations in the abundance of this species. Our analysis provided little evidence that herbivores are limited by primary production on Bylot Island. In contrast, we measured strong predator-prey interactions, which supports the hypothesis that this food web is primarily controlled by top-down forces. The presence of allochthonous resources subsidizing top predators and the absence of large herbivores may partly explain the predominant role of predation in this low-productivity ecosystem.

7 CFR 14.6 - Criteria for determining the primary purpose of payments with respect to potential exclusion from...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 1 2014-01-01 2014-01-01 false Criteria for determining the primary purpose of... Secretary of Agriculture DETERMINING THE PRIMARY PURPOSE OF CERTAIN PAYMENTS FOR FEDERAL TAX PURPOSES § 14.6 Criteria for determining the primary purpose of payments with respect to potential exclusion from gross...

7 CFR 14.6 - Criteria for determining the primary purpose of payments with respect to potential exclusion from...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 1 2012-01-01 2012-01-01 false Criteria for determining the primary purpose of... Secretary of Agriculture DETERMINING THE PRIMARY PURPOSE OF CERTAIN PAYMENTS FOR FEDERAL TAX PURPOSES § 14.6 Criteria for determining the primary purpose of payments with respect to potential exclusion from gross...

A 4-year treatment with clodronate plus calcium and vitamin D supplements does not improve bone mass in primary biliary cirrhosis.

PubMed

Floreani, A; Carderi, I; Ferrara, F; Rizzotto, E R; Luisetto, G; Camozzi, V; Baldo, V

2007-06-01

International guidelines for managing osteoporosis in cirrhosis or severe cholestasis indicate a <-2.5 t-score as a cut-off for medical treatment, while no treatment is recommended in the case of osteopenia (t-scores ranging from -1.0 to -2.5). We conducted a prospective study in primary biliary cirrhosis with a view to optimizing the rationale for the medical treatment of bone loss. All naïve post-menopausal women with primary biliary cirrhosis were enrolled in the study. Bone metabolism was evaluated by measuring 25-hydroxy-vitamin D, parathyroid hormone, osteocalcin. Bone mineral density was assessed at the lumbar spine by dual-photon X-ray absorptiometry at the baseline and every 2 years for up to 4 years. Patients with either osteopenia or osteoporosis received the following treatment: oral calcium carbonate (1000 mg/day)+vitamin D3 (880 IU/day)+i.m. disodium clodronate 100mg every 10 days for 4 years. Ninety-six patients completed the study: 30 had a normal bone mineral density (group 1), 37 had osteopenia (group 2), 29 had osteoporosis (group 3). No significant differences in biochemical parameters of bone metabolism were observed between the three groups. A total of 288 bone mineral density measurements were taken. Linear regression analysis failed to reveal significant changes in t-score over the follow-up in all groups. A 4-year treatment with clodronate+calcium/vitamin D3 supplements does not significantly improve osteoporosis or osteopenia in primary biliary cirrhosis women in menopause, but prevents the natural bone loss in these patients. Extensive international trials are warranted to optimize the prevention and treatment of bone loss in primary biliary cirrhosis.

Association of the g.19074G>A genetic variant in the osteoprotegerin gene with bone mineral density in Chinese postmenopausal women.

PubMed

Zhang, Y D; Zhang, Z; Zhou, N F; Jia, W T; Cheng, X G; Wei, X J

2014-08-28

Primary osteoporosis is a common health problem in postmenopausal women. This study aimed to detect the association of the g.19074G>A genetic variant in the osteoprotegerin gene (OPG) with bone mineral density (BMD) and primary osteoporosis. The created restriction site-polymerase chain reaction method was used to investigate the g.19074G>A genetic variant. The BMD of the femoral neck hip, lumbar spine (L2-4), and total hip were assessed by dual-energy X-ray absorptiometry (DEXA) in 856 unrelated Chinese postmenopausal women. We found significant differences in the BMDs of the femoral neck hip, lumbar spine (L2-4), and total hip among different genotypes; individuals with the GG genotype had significantly higher BMDs than those with the GA and AA genotypes (P < 0.05). Our results indicated that the A allele was an increased risk factor for primary osteoporosis and the g.19074G>A genetic variant of the OPG gene was associated with BMD and primary osteoporosis in Chinese postmenopausal women.

Determination of PM mass emissions from an aircraft turbine engine using particle effective density

NASA Astrophysics Data System (ADS)

Durdina, L.; Brem, B. T.; Abegglen, M.; Lobo, P.; Rindlisbacher, T.; Thomson, K. A.; Smallwood, G. J.; Hagen, D. E.; Sierau, B.; Wang, J.

2014-12-01

Inventories of particulate matter (PM) emissions from civil aviation and air quality models need to be validated using up-to-date measurement data corrected for sampling artifacts. We compared the measured black carbon (BC) mass and the total PM mass determined from particle size distributions (PSD) and effective density for a commercial turbofan engine CFM56-7B26/3. The effective density was then used to calculate the PM mass losses in the sampling system. The effective density was determined using a differential mobility analyzer and a centrifugal particle mass analyzer, and increased from engine idle to take-off by up to 60%. The determined mass-mobility exponents ranged from 2.37 to 2.64. The mean effective density determined by weighting the effective density distributions by PM volume was within 10% of the unit density (1000 kg/m3) that is widely assumed in aircraft PM studies. We found ratios close to unity between the PM mass determined by the integrated PSD method and the real-time BC mass measurements. The integrated PSD method achieved higher precision at ultra-low PM concentrations at which current mass instruments reach their detection limit. The line loss model predicted ∼60% PM mass loss at engine idle, decreasing to ∼27% at high thrust. Replacing the effective density distributions with unit density lead to comparable estimates that were within 20% and 5% at engine idle and high thrust, respectively. These results could be used for the development of a robust method for sampling loss correction of the future PM emissions database from commercial aircraft engines.

Laser antisepsis of Phorphyromonas gingivalis in vitro with dental lasers

NASA Astrophysics Data System (ADS)

Harris, David M.

2004-05-01

It has been shown that both pulsed Nd:YAG (1064nm) and continuous diode (810nm) dental lasers kill pathogenic bacteria (laser antisepsis), but a quantitative method for determining clinical dosimetry does not exist. The purpose of this study was to develop a method to quantify the efficacy of ablation of Porphyromonas gingivalis (Pg) in vitro for two different lasers. The ablation thresholds for the two lasers were compared in the following manner. The energy density was measured as a function of distance from the output of the fiber-optic delivery system. Pg cultures were grown on blood agar plates under standard anaerobic conditions. Blood agar provides an approximation of gingival tissue for the wavelengths tested in having hemoglobin as a primary absorber. Single pulses (Nd:YAG: 100- Œs diode: 100-msec) of laser energy were delivered to Pg colonies and the energy density was increased until the appearance of a small plume was observed coincident with a laser pulse. The energy density at this point defines the ablation threshold. Ablation thresholds to a single pulse were determined for both Pg and for blood agar alone. The large difference in ablation thresholds between the pigmented pathogen and the host matrix for pulsed-Nd:YAG represented a significant therapeutic ratio and Pg was ablated without visible effect on the blood agar. Near threshold the 810-nm diode laser destroyed both the pathogen and the gel. Clinically, the pulsed Nd:YAG may selectively destroy pigmented pathogens leaving the surrounding tissue intact. The 810-nm diode laser may not demonstrate this selectivity due to its longer pulse length and greater absorption by hemoglobin.

Pseudorapidity distributions of charged hadrons in proton-lead collisions at √{s_{NN}}=5.02 and 8.16 TeV

NASA Astrophysics Data System (ADS)

Sirunyan, A. M.; Tumasyan, A.; Adam, W.; Ambrogi, F.; Asilar, E.; Bergauer, T.; Brandstetter, J.; Brondolin, E.; Drag-icevic, M.; Erö, J.; Flechl, M.; Friedl, M.; Frühwirth, R.; Ghete, V. M.; Grossmann, J.; Hrubec, J.; Jeitler, M.; König, A.; Krammer, N.; Krätschmer, I.; Liko, D.; Madlener, T.; Mikulec, I.; Pree, E.; Rad, N.; Rohringer, H.; Schieck, J.; Schöfbeck, R.; Spanring, M.; Spitzbart, D.; Waltenberger, W.; Wittmann, J.; Wulz, C.-E.; Zarucki, M.; Chekhovsky, V.; Mossolov, V.; Suarez Gonzalez, J.; De Wolf, E. A.; Di Croce, D.; Janssen, X.; Lauwers, J.; Van De Klundert, M.; Van Haevermaet, H.; Van Mechelen, P.; Van Remortel, N.; Abu Zeid, S.; Blekman, F.; D'Hondt, J.; De Bruyn, I.; De Clercq, J.; Deroover, K.; Flouris, G.; Lontkovskyi, D.; Lowette, S.; Moortgat, S.; Moreels, L.; Python, Q.; Skovpen, K.; Tavernier, S.; Van Doninck, W.; Van Mulders, P.; Van Parijs, I.; Beghin, D.; Brun, H.; Clerbaux, B.; De Lentdecker, G.; Delannoy, H.; Dorney, B.; Fasanella, G.; Favart, L.; Goldouzian, R.; Grebenyuk, A.; Karapostoli, G.; Lenzi, T.; Luetic, J.; Maerschalk, T.; Marinov, A.; Seva, T.; Starling, E.; Vander Velde, C.; Vanlaer, P.; Vannerom, D.; Yonamine, R.; Zenoni, F.; Zhang, F.; Cimmino, A.; Cornelis, T.; Dobur, D.; Fagot, A.; Gul, M.; Khvastunov, I.; Poyraz, D.; Roskas, C.; Salva, S.; Tytgat, M.; Verbeke, W.; Zaganidis, N.; Bakhshiansohi, H.; Bondu, O.; Brochet, S.; Bruno, G.; Caputo, C.; Caudron, A.; David, P.; De Visscher, S.; Delaere, C.; Delcourt, M.; Francois, B.; Giammanco, A.; Komm, M.; Krintiras, G.; Lemaitre, V.; Magitteri, A.; Mertens, A.; Musich, M.; Piotrzkowski, K.; Quertenmont, L.; Saggio, A.; Vidal Marono, M.; Wertz, S.; Zobec, J.; Beliy, N.; Aldá Júnior, W. L.; Alves, F. L.; Alves, G. A.; Brito, L.; Correa Martins Junior, M.; Hensel, C.; Moraes, A.; Pol, M. E.; Rebello Teles, P.; Belchior Batista Das Chagas, E.; Carvalho, W.; Chinellato, J.; Coelho, E.; Da Costa, E. M.; Da Silveira, G. G.; De Jesus Damiao, D.; Fonseca De Souza, S.; Huertas Guativa, L. M.; Malbouisson, H.; Melo De Almeida, M.; Mora Herrera, C.; Mundim, L.; Nogima, H.; Sanchez Rosas, L. J.; Santoro, A.; Sznajder, A.; Thiel, M.; Tonelli Manganote, E. J.; Torres Da Silva De Araujo, F.; Vilela Pereira, A.; Ahuja, S.; Bernardes, C. A.; Fernandez Perez Tomei, T. R.; Gregores, E. M.; Mercadante, P. G.; Novaes, S. F.; Padula, Sandra S.; Romero Abad, D.; Ruiz Vargas, J. C.; Aleksandrov, A.; Hadjiiska, R.; Iaydjiev, P.; Misheva, M.; Rodozov, M.; Shopova, M.; Sultanov, G.; Dimitrov, A.; Glushkov, I.; Litov, L.; Pavlov, B.; Petkov, P.; Fang, W.; Gao, X.; Yuan, L.; Ahmad, M.; Bian, J. G.; Chen, G. M.; Chen, H. S.; Chen, M.; Chen, Y.; Jiang, C. H.; Leggat, D.; Liao, H.; Liu, Z.; Romeo, F.; Shaheen, S. M.; Spiezia, A.; Tao, J.; Wang, C.; Wang, Z.; Yazgan, E.; Zhang, H.; Zhang, S.; Zhao, J.; Ban, Y.; Chen, G.; Li, Q.; Liu, S.; Mao, Y.; Qian, S. J.; Wang, D.; Xu, Z.; Avila, C.; Cabrera, A.; Chaparro Sierra, L. F.; Florez, C.; González Hernández, C. F.; Ruiz Alvarez, J. D.; Segura Delgado, M. A.; Courbon, B.; Godinovic, N.; Lelas, D.; Puljak, I.; Ribeiro Cipriano, P. M.; Sculac, T.; Antunovic, Z.; Kovac, M.; Brigljevic, V.; Ferencek, D.; Kadija, K.; Mesic, B.; Starodumov, A.; Susa, T.; Ather, M. W.; Attikis, A.; Mavromanolakis, G.; Mousa, J.; Nicolaou, C.; Ptochos, F.; Razis, P. A.; Rykaczewski, H.; Finger, M.; Finger, M.; Carrera Jarrin, E.; Abdelalim, A. A.; Mohammed, Y.; Salama, E.; Dewanjee, R. K.; Kadastik, M.; Perrini, L.; Raidal, M.; Tiko, A.; Veelken, C.; Eerola, P.; Kirschenmann, H.; Pekkanen, J.; Voutilainen, M.; Havukainen, J.; Heikkilä, J. K.; Järvinen, T.; Karimäki, V.; Kinnunen, R.; Lampén, T.; Lassila-Perini, K.; Laurila, S.; Lehti, S.; Lindén, T.; Luukka, P.; Siikonen, H.; Tuominen, E.; Tuominiemi, J.; Talvitie, J.; Tuuva, T.; Besancon, M.; Couderc, F.; Dejardin, M.; Denegri, D.; Faure, J. L.; Ferri, F.; Ganjour, S.; Ghosh, S.; Givernaud, A.; Gras, P.; Hamel de Monchenault, G.; Jarry, P.; Kucher, I.; Leloup, C.; Locci, E.; Machet, M.; Malcles, J.; Negro, G.; Rander, J.; Rosowsky, A.; Sahin, M. Ö.; Titov, M.; Abdulsalam, A.; Amendola, C.; Antropov, I.; Baffioni, S.; Beaudette, F.; Busson, P.; Cadamuro, L.; Charlot, C.; Granier de Cassagnac, R.; Jo, M.; Lisniak, S.; Lobanov, A.; Martin Blanco, J.; Nguyen, M.; Ochando, C.; Ortona, G.; Paganini, P.; Pigard, P.; Salerno, R.; Sauvan, J. B.; Sirois, Y.; Stahl Leiton, A. G.; Strebler, T.; Yilmaz, Y.; Zabi, A.; Zghiche, A.; Agram, J.-L.; Andrea, J.; Bloch, D.; Brom, J.-M.; Buttignol, M.; Chabert, E. C.; Chanon, N.; Collard, C.; Conte, E.; Coubez, X.; Fontaine, J.-C.; Gelé, D.; Goerlach, U.; Jansová, M.; Le Bihan, A.-C.; Tonon, N.; Van Hove, P.; Gadrat, S.; Beauceron, S.; Bernet, C.; Boudoul, G.; Chierici, R.; Contardo, D.; Depasse, P.; El Mamouni, H.; Fay, J.; Finco, L.; Gascon, S.; Gouzevitch, M.; Grenier, G.; Ille, B.; Lagarde, F.; Laktineh, I. B.; Lethuillier, M.; Mirabito, L.; Pequegnot, A. L.; Perries, S.; Popov, A.; Sordini, V.; Vander Donckt, M.; Viret, S.; Toriashvili, T.; Tsamalaidze, Z.; Autermann, C.; Feld, L.; Kiesel, M. K.; Klein, K.; Lipinski, M.; Preuten, M.; Schomakers, C.; Schulz, J.; Zhukov, V.; Albert, A.; Dietz-Laursonn, E.; Duchardt, D.; Endres, M.; Erdmann, M.; Erdweg, S.; Esch, T.; Fischer, R.; Güth, A.; Hamer, M.; Hebbeker, T.; Heidemann, C.; Hoepfner, K.; Knutzen, S.; Merschmeyer, M.; Meyer, A.; Millet, P.; Mukherjee, S.; Pook, T.; Radziej, M.; Reithler, H.; Rieger, M.; Scheuch, F.; Teyssier, D.; Thüer, S.; Flügge, G.; Kargoll, B.; Kress, T.; Künsken, A.; Müller, T.; Nehrkorn, A.; Nowack, A.; Pistone, C.; Pooth, O.; Stahl, A.; Aldaya Martin, M.; Arndt, T.; Asawatangtrakuldee, C.; Beernaert, K.; Behnke, O.; Behrens, U.; Bermúdez Martínez, A.; Bin Anuar, A. A.; Borras, K.; Botta, V.; Campbell, A.; Connor, P.; Contreras-Campana, C.; Costanza, F.; Diez Pardos, C.; Eckerlin, G.; Eckstein, D.; Eichhorn, T.; Eren, E.; Gallo, E.; Garay Garcia, J.; Geiser, A.; Gizhko, A.; Grados Luyando, J. M.; Grohsjean, A.; Gunnellini, P.; Guthoff, M.; Harb, A.; Hauk, J.; Hempel, M.; Jung, H.; Kalogeropoulos, A.; Kasemann, M.; Keaveney, J.; Kleinwort, C.; Korol, I.; Krücker, D.; Lange, W.; Lelek, A.; Lenz, T.; Leonard, J.; Lipka, K.; Lohmann, W.; Mankel, R.; Melzer-Pellmann, I.-A.; Meyer, A. B.; Mittag, G.; Mnich, J.; Mussgiller, A.; Ntomari, E.; Pitzl, D.; Raspereza, A.; Savitskyi, M.; Saxena, P.; Shevchenko, R.; Spannagel, S.; Stefaniuk, N.; Van Onsem, G. P.; Walsh, R.; Wen, Y.; Wichmann, K.; Wissing, C.; Zenaiev, O.; Aggleton, R.; Bein, S.; Blobel, V.; Centis Vignali, M.; Dreyer, T.; Garutti, E.; Gonzalez, D.; Haller, J.; Hinzmann, A.; Hoffmann, M.; Karavdina, A.; Klanner, R.; Kogler, R.; Kovalchuk, N.; Kurz, S.; Lapsien, T.; Marchesini, I.; Marconi, D.; Meyer, M.; Niedziela, M.; Nowatschin, D.; Pantaleo, F.; Peiffer, T.; Perieanu, A.; Scharf, C.; Schleper, P.; Schmidt, A.; Schumann, S.; Schwandt, J.; Sonneveld, J.; Stadie, H.; Steinbrück, G.; Stober, F. M.; Stöver, M.; Tholen, H.; Troendle, D.; Usai, E.; Vanhoefer, A.; Vormwald, B.; Akbiyik, M.; Barth, C.; Baselga, M.; Baur, S.; Butz, E.; Caspart, R.; Chwalek, T.; Colombo, F.; De Boer, W.; Dierlamm, A.; Faltermann, N.; Freund, B.; Friese, R.; Giffels, M.; Harrendorf, M. A.; Hartmann, F.; Heindl, S. M.; Husemann, U.; Kassel, F.; Kudella, S.; Mildner, H.; Mozer, M. U.; Müller, Th.; Plagge, M.; Quast, G.; Rabbertz, K.; Schröder, M.; Shvetsov, I.; Sieber, G.; Simonis, H. J.; Ulrich, R.; Wayand, S.; Weber, M.; Weiler, T.; Williamson, S.; Wöhrmann, C.; Wolf, R.; Anagnostou, G.; Daskalakis, G.; Geralis, T.; Kyriakis, A.; Loukas, D.; Topsis-Giotis, I.; Karathanasis, G.; Kesisoglou, S.; Panagiotou, A.; Saoulidou, N.; Kousouris, K.; Evangelou, I.; Foudas, C.; Kokkas, P.; Mallios, S.; Manthos, N.; Papadopoulos, I.; Paradas, E.; Strologas, J.; Triantis, F. A.; Csanad, M.; Filipovic, N.; Pasztor, G.; Surányi, O.; Veres, G. I.; Bencze, G.; Hajdu, C.; Horvath, D.; Hunyadi, Á.; Sikler, F.; Veszpremi, V.; Beni, N.; Czellar, S.; Karancsi, J.; Makovec, A.; Molnar, J.; Szillasi, Z.; Bartók, M.; Raics, P.; Trocsanyi, Z. L.; Ujvari, B.; Choudhury, S.; Komaragiri, J. R.; Bahinipati, S.; Bhowmik, S.; Mal, P.; Mandal, K.; Nayak, A.; Sahoo, D. K.; Sahoo, N.; Swain, S. K.; Bansal, S.; Beri, S. B.; Bhatnagar, V.; Chawla, R.; Dhingra, N.; Kalsi, A. K.; Kaur, A.; Kaur, M.; Kaur, S.; Kumar, R.; Kumari, P.; Mehta, A.; Singh, J. B.; Walia, G.; Kumar, Ashok; Shah, Aashaq; Bhardwaj, A.; Chauhan, S.; Choudhary, B. C.; Garg, R. B.; Keshri, S.; Kumar, A.; Malhotra, S.; Naimuddin, M.; Ranjan, K.; Sharma, R.; Bhardwaj, R.; Bhattacharya, R.; Bhattacharya, S.; Bhawandeep, U.; Dey, S.; Dutt, S.; Dutta, S.; Ghosh, S.; Majumdar, N.; Modak, A.; Mondal, K.; Mukhopadhyay, S.; Nandan, S.; Purohit, A.; Roy, A.; Roy Chowdhury, S.; Sarkar, S.; Sharan, M.; Thakur, S.; Behera, P. K.; Chudasama, R.; Dutta, D.; Jha, V.; Kumar, V.; Mohanty, A. K.; Netrakanti, P. K.; Pant, L. M.; Shukla, P.; Topkar, A.; Aziz, T.; Dugad, S.; Mahakud, B.; Mitra, S.; Mohanty, G. B.; Sur, N.; Sutar, B.; Banerjee, S.; Bhattacharya, S.; Chatterjee, S.; Das, P.; Guchait, M.; Jain, Sa.; Kumar, S.; Maity, M.; Majumder, G.; Mazumdar, K.; Sarkar, T.; Wickramage, N.; Chauhan, S.; Dube, S.; Hegde, V.; Kapoor, A.; Kothekar, K.; Pandey, S.; Rane, A.; Sharma, S.; Chenarani, S.; Eskandari Tadavani, E.; Etesami, S. M.; Khakzad, M.; Mohammadi Najafabadi, M.; Naseri, M.; Paktinat Mehdiabadi, S.; Rezaei Hosseinabadi, F.; Safarzadeh, B.; Zeinali, M.; Felcini, M.; Grunewald, M.; Abbrescia, M.; Calabria, C.; Colaleo, A.; Creanza, D.; Cristella, L.; De Filippis, N.; De Palma, M.; Errico, F.; Fiore, L.; Iaselli, G.; Lezki, S.; Maggi, G.; Maggi, M.; Miniello, G.; My, S.; Nuzzo, S.; Pompili, A.; Pugliese, G.; Radogna, R.; Ranieri, A.; Selvaggi, G.; Sharma, A.; Silvestris, L.; Venditti, R.; Verwilligen, P.; Abbiendi, G.; Battilana, C.; Bonacorsi, D.; Borgonovi, L.; Braibant-Giacomelli, S.; Campanini, R.; Capiluppi, P.; Castro, A.; Cavallo, F. R.; Chhibra, S. S.; Codispoti, G.; Cuffiani, M.; Dallavalle, G. M.; Fabbri, F.; Fanfani, A.; Fasanella, D.; Giacomelli, P.; Grandi, C.; Guiducci, L.; Marcellini, S.; Masetti, G.; Montanari, A.; Navarria, F. L.; Perrotta, A.; Rossi, A. M.; Rovelli, T.; Siroli, G. P.; Tosi, N.; Albergo, S.; Costa, S.; Di Mattia, A.; Giordano, F.; Potenza, R.; Tricomi, A.; Tuve, C.; Barbagli, G.; Chatterjee, K.; Ciulli, V.; Civinini, C.; D'Alessandro, R.; Focardi, E.; Lenzi, P.; Meschini, M.; Paoletti, S.; Russo, L.; Sguazzoni, G.; Strom, D.; Viliani, L.; Benussi, L.; Bianco, S.; Fabbri, F.; Piccolo, D.; Primavera, F.; Calvelli, V.; Ferro, F.; Robutti, E.; Tosi, S.; Benaglia, A.; Beschi, A.; Brianza, L.; Brivio, F.; Ciriolo, V.; Dinardo, M. E.; Fiorendi, S.; Gennai, S.; Ghezzi, A.; Govoni, P.; Malberti, M.; Malvezzi, S.; Manzoni, R. A.; Menasce, D.; Moroni, L.; Paganoni, M.; Pauwels, K.; Pedrini, D.; Pigazzini, S.; Ragazzi, S.; Redaelli, N.; Tabarelli de Fatis, T.; Buontempo, S.; Cavallo, N.; Di Guida, S.; Fabozzi, F.; Fienga, F.; Iorio, A. O. M.; Khan, W. A.; Lista, L.; Meola, S.; Paolucci, P.; Sciacca, C.; Thyssen, F.; Azzi, P.; Bacchetta, N.; Benato, L.; Bisello, D.; Boletti, A.; Carlin, R.; Carvalho Antunes De Oliveira, A.; Checchia, P.; De Castro Manzano, P.; Dorigo, T.; Dosselli, U.; Gasparini, F.; Gasparini, U.; Gozzelino, A.; Lacaprara, S.; Margoni, M.; Meneguzzo, A. T.; Pozzobon, N.; Ronchese, P.; Rossin, R.; Simonetto, F.; Torassa, E.; Zanetti, M.; Zotto, P.; Zumerle, G.; Braghieri, A.; Magnani, A.; Montagna, P.; Ratti, S. P.; Re, V.; Ressegotti, M.; Riccardi, C.; Salvini, P.; Vai, I.; Vitulo, P.; Alunni Solestizi, L.; Biasini, M.; Bilei, G. M.; Cecchi, C.; Ciangottini, D.; Fanò, L.; Lariccia, P.; Leonardi, R.; Manoni, E.; Mantovani, G.; Mariani, V.; Menichelli, M.; Rossi, A.; Santocchia, A.; Spiga, D.; Androsov, K.; Azzurri, P.; Bagliesi, G.; Boccali, T.; Borrello, L.; Castaldi, R.; Ciocci, M. A.; Dell'Orso, R.; Fedi, G.; Giannini, L.; Giassi, A.; Grippo, M. T.; Ligabue, F.; Lomtadze, T.; Manca, E.; Mandorli, G.; Messineo, A.; Palla, F.; Rizzi, A.; Savoy-Navarro, A.; Spagnolo, P.; Tenchini, R.; Tonelli, G.; Venturi, A.; Verdini, P. G.; Barone, L.; Cavallari, F.; Cipriani, M.; Daci, N.; Del Re, D.; Di Marco, E.; Diemoz, M.; Gelli, S.; Longo, E.; Margaroli, F.; Marzocchi, B.; Meridiani, P.; Organtini, G.; Paramatti, R.; Preiato, F.; Rahatlou, S.; Rovelli, C.; Santanastasio, F.; Amapane, N.; Arcidiacono, R.; Argiro, S.; Arneodo, M.; Bartosik, N.; Bellan, R.; Biino, C.; Cartiglia, N.; Cenna, F.; Costa, M.; Covarelli, R.; Degano, A.; Demaria, N.; Kiani, B.; Mariotti, C.; Maselli, S.; Migliore, E.; Monaco, V.; Monteil, E.; Monteno, M.; Obertino, M. M.; Pacher, L.; Pastrone, N.; Pelliccioni, M.; Pinna Angioni, G. L.; Ravera, F.; Romero, A.; Ruspa, M.; Sacchi, R.; Shchelina, K.; Sola, V.; Solano, A.; Staiano, A.; Traczyk, P.; Belforte, S.; Casarsa, M.; Cossutti, F.; Della Ricca, G.; Zanetti, A.; Kim, D. H.; Kim, G. N.; Kim, M. S.; Lee, J.; Lee, S.; Lee, S. W.; Moon, C. S.; Oh, Y. D.; Sekmen, S.; Son, D. C.; Yang, Y. C.; Lee, A.; Kim, H.; Moon, D. H.; Oh, G.; Brochero Cifuentes, J. A.; Goh, J.; Kim, T. J.; Cho, S.; Choi, S.; Go, Y.; Gyun, D.; Ha, S.; Hong, B.; Jo, Y.; Kim, Y.; Lee, K.; Lee, K. S.; Lee, S.; Lim, J.; Park, S. K.; Roh, Y.; Almond, J.; Kim, J.; Kim, J. S.; Lee, H.; Lee, K.; Nam, K.; Oh, S. B.; Radburn-Smith, B. C.; Seo, S. h.; Yang, U. K.; Yoo, H. D.; Yu, G. B.; Choi, M.; Kim, H.; Kim, J. H.; Lee, J. S. H.; Park, I. C.; Choi, Y.; Hwang, C.; Lee, J.; Yu, I.; Dudenas, V.; Juodagalvis, A.; Vaitkus, J.; Ahmed, I.; Ibrahim, Z. A.; Ali, M. A. B. Md; Mohamad Idris, F.; Wan Abdullah, W. A. T.; Yusli, M. N.; Zolkapli, Z.; Reyes-Almanza, R.; Ramirez-Sanchez, G.; Duran-Osuna, M. C.; Castilla-Valdez, H.; De La Cruz-Burelo, E.; Heredia-De La Cruz, I.; Rabadan-Trejo, R. I.; Lopez-Fernandez, R.; Mejia Guisao, J.; Sanchez-Hernandez, A.; Carrillo Moreno, S.; Oropeza Barrera, C.; Vazquez Valencia, F.; Pedraza, I.; Salazar Ibarguen, H. A.; Uribe Estrada, C.; Morelos Pineda, A.; Krofcheck, D.; Butler, P. H.; Ahmad, A.; Ahmad, M.; Hassan, Q.; Hoorani, H. R.; Saddique, A.; Shah, M. A.; Shoaib, M.; Waqas, M.; Bialkowska, H.; Bluj, M.; Boimska, B.; Frueboes, T.; Górski, M.; Kazana, M.; Nawrocki, K.; Szleper, M.; Zalewski, P.; Bunkowski, K.; Byszuk, A.; Doroba, K.; Kalinowski, A.; Konecki, M.; Krolikowski, J.; Misiura, M.; Olszewski, M.; Pyskir, A.; Walczak, M.; Bargassa, P.; Beirão Da Cruz E Silva, C.; Di Francesco, A.; Faccioli, P.; Galinhas, B.; Gallinaro, M.; Hollar, J.; Leonardo, N.; Lloret Iglesias, L.; Nemallapudi, M. V.; Seixas, J.; Strong, G.; Toldaiev, O.; Vadruccio, D.; Varela, J.; Afanasiev, S.; Bunin, P.; Gavrilenko, M.; Golutvin, I.; Gorbunov, I.; Kamenev, A.; Karjavin, V.; Lanev, A.; Malakhov, A.; Matveev, V.; Palichik, V.; Perelygin, V.; Shmatov, S.; Shulha, S.; Skatchkov, N.; Smirnov, V.; Voytishin, N.; Zarubin, A.; Ivanov, Y.; Kim, V.; Kuznetsova, E.; Levchenko, P.; Murzin, V.; Oreshkin, V.; Smirnov, I.; Sulimov, V.; Uvarov, L.; Vavilov, S.; Vorobyev, A.; Andreev, Yu.; Dermenev, A.; Gninenko, S.; Golubev, N.; Karneyeu, A.; Kirsanov, M.; Krasnikov, N.; Pashenkov, A.; Tlisov, D.; Toropin, A.; Epshteyn, V.; Gavrilov, V.; Lychkovskaya, N.; Popov, V.; Pozdnyakov, I.; Safronov, G.; Spiridonov, A.; Stepennov, A.; Toms, M.; Vlasov, E.; Zhokin, A.; Aushev, T.; Bylinkin, A.; Chadeeva, M.; Parygin, P.; Philippov, D.; Polikarpov, S.; Popova, E.; Rusinov, V.; Andreev, V.; Azarkin, M.; Dremin, I.; Kirakosyan, M.; Terkulov, A.; Baskakov, A.; Belyaev, A.; Boos, E.; Demiyanov, A.; Ershov, A.; Gribushin, A.; Kodolova, O.; Korotkikh, V.; Lokhtin, I.; Miagkov, I.; Obraztsov, S.; Petrushanko, S.; Savrin, V.; Snigirev, A.; Vardanyan, I.; Blinov, V.; Skovpen, Y.; Shtol, D.; Azhgirey, I.; Bayshev, I.; Bitioukov, S.; Elumakhov, D.; Kachanov, V.; Kalinin, A.; Konstantinov, D.; Mandrik, P.; Petrov, V.; Ryutin, R.; Sobol, A.; Troshin, S.; Tyurin, N.; Uzunian, A.; Volkov, A.; Adzic, P.; Cirkovic, P.; Devetak, D.; Dordevic, M.; Milosevic, J.; Rekovic, V.; Alcaraz Maestre, J.; Barrio Luna, M.; Cerrada, M.; Colino, N.; De La Cruz, B.; Delgado Peris, A.; Escalante Del Valle, A.; Fernandez Bedoya, C.; Fernández Ramos, J. P.; Flix, J.; Fouz, M. C.; Gonzalez Lopez, O.; Goy Lopez, S.; Hernandez, J. M.; Josa, M. I.; Moran, D.; Pérez-Calero Yzquierdo, A.; Puerta Pelayo, J.; Quintario Olmeda, A.; Redondo, I.; Romero, L.; Soares, M. S.; Álvarez Fernández, A.; Albajar, C.; de Trocóniz, J. F.; Missiroli, M.; Cuevas, J.; Erice, C.; Fernandez Menendez, J.; Gonzalez Caballero, I.; González Fernández, J. R.; Palencia Cortezon, E.; Sanchez Cruz, S.; Vischia, P.; Vizan Garcia, J. M.; Cabrillo, I. J.; Calderon, A.; Chazin Quero, B.; Curras, E.; Duarte Campderros, J.; Fernandez, M.; Garcia-Ferrero, J.; Gomez, G.; Lopez Virto, A.; Marco, J.; Martinez Rivero, C.; Martinez Ruiz del Arbol, P.; Matorras, F.; Piedra Gomez, J.; Rodrigo, T.; Ruiz-Jimeno, A.; Scodellaro, L.; Trevisani, N.; Vila, I.; Vilar Cortabitarte, R.; Abbaneo, D.; Akgun, B.; Auffray, E.; Baillon, P.; Ball, A. H.; Barney, D.; Bendavid, J.; Bianco, M.; Bloch, P.; Bocci, A.; Botta, C.; Camporesi, T.; Castello, R.; Cepeda, M.; Cerminara, G.; Chapon, E.; Chen, Y.; d'Enterria, D.; Dabrowski, A.; Daponte, V.; David, A.; De Gruttola, M.; De Roeck, A.; Deelen, N.; Dobson, M.; du Pree, T.; Dünser, M.; Dupont, N.; Elliott-Peisert, A.; Everaerts, P.; Fallavollita, F.; Franzoni, G.; Fulcher, J.; Funk, W.; Gigi, D.; Gilbert, A.; Gill, K.; Glege, F.; Gulhan, D.; Harris, P.; Hegeman, J.; Innocente, V.; Jafari, A.; Janot, P.; Karacheban, O.; Kieseler, J.; Knünz, V.; Kornmayer, A.; Kortelainen, M. J.; Krammer, M.; Lange, C.; Lecoq, P.; Lourenço, C.; Lucchini, M. T.; Malgeri, L.; Mannelli, M.; Martelli, A.; Meijers, F.; Merlin, J. A.; Mersi, S.; Meschi, E.; Milenovic, P.; Moortgat, F.; Mulders, M.; Neugebauer, H.; Ngadiuba, J.; Orfanelli, S.; Orsini, L.; Pape, L.; Perez, E.; Peruzzi, M.; Petrilli, A.; Petrucciani, G.; Pfeiffer, A.; Pierini, M.; Rabady, D.; Racz, A.; Reis, T.; Rolandi, G.; Rovere, M.; Sakulin, H.; Schäfer, C.; Schwick, C.; Seidel, M.; Selvaggi, M.; Sharma, A.; Silva, P.; Sphicas, P.; Stakia, A.; Steggemann, J.; Stoye, M.; Tosi, M.; Treille, D.; Triossi, A.; Tsirou, A.; Veckalns, V.; Verweij, M.; Zeuner, W. D.; Bertl, W.; Caminada, L.; Deiters, K.; Erdmann, W.; Horisberger, R.; Ingram, Q.; Kaestli, H. C.; Kotlinski, D.; Langenegger, U.; Rohe, T.; Wiederkehr, S. A.; Backhaus, M.; Bäni, L.; Berger, P.; Bianchini, L.; Casal, B.; Dissertori, G.; Dittmar, M.; Donegà, M.; Dorfer, C.; Grab, C.; Heidegger, C.; Hits, D.; Hoss, J.; Kasieczka, G.; Klijnsma, T.; Lustermann, W.; Mangano, B.; Marionneau, M.; Meinhard, M. T.; Meister, D.; Micheli, F.; Musella, P.; Nessi-Tedaldi, F.; Pandolfi, F.; Pata, J.; Pauss, F.; Perrin, G.; Perrozzi, L.; Quittnat, M.; Reichmann, M.; Sanz Becerra, D. A.; Schönenberger, M.; Shchutska, L.; Tavolaro, V. R.; Theofilatos, K.; Vesterbacka Olsson, M. L.; Wallny, R.; Zhu, D. H.; Aarrestad, T. K.; Amsler, C.; Canelli, M. F.; De Cosa, A.; Del Burgo, R.; Donato, S.; Galloni, C.; Hreus, T.; Kilminster, B.; Pinna, D.; Rauco, G.; Robmann, P.; Salerno, D.; Schweiger, K.; Seitz, C.; Takahashi, Y.; Zucchetta, A.; Candelise, V.; Doan, T. H.; Jain, Sh.; Khurana, R.; Kuo, C. M.; Lin, W.; Pozdnyakov, A.; Yu, S. S.; Kumar, Arun; Chang, P.; Chao, Y.; Chen, K. F.; Chen, P. H.; Fiori, F.; Hou, W.-S.; Hsiung, Y.; Liu, Y. F.; Lu, R.-S.; Paganis, E.; Psallidas, A.; Steen, A.; Tsai, J. f.; Asavapibhop, B.; Kovitanggoon, K.; Singh, G.; Srimanobhas, N.; Bakirci, M. N.; Bat, A.; Boran, F.; Damarseckin, S.; Demiroglu, Z. S.; Dozen, C.; Girgis, S.; Gokbulut, G.; Guler, Y.; Hos, I.; Kangal, E. E.; Kara, O.; Kiminsu, U.; Oglakci, M.; Onengut, G.; Ozdemir, K.; Ozturk, S.; Polatoz, A.; Tali, B.; Tok, U. G.; Topakli, H.; Turkcapar, S.; Zorbakir, I. S.; Zorbilmez, C.; Bilin, B.; Karapinar, G.; Ocalan, K.; Yalvac, M.; Zeyrek, M.; Gülmez, E.; Kaya, M.; Kaya, O.; Tekten, S.; Yetkin, E. A.; Agaras, M. N.; Atay, S.; Cakir, A.; Cankocak, K.; Grynyov, B.; Levchuk, L.; Ball, F.; Beck, L.; Brooke, J. J.; Burns, D.; Clement, E.; Cussans, D.; Davignon, O.; Flacher, H.; Goldstein, J.; Heath, G. P.; Heath, H. F.; Kreczko, L.; Newbold, D. M.; Paramesvaran, S.; Sakuma, T.; Seif El Nasr-storey, S.; Smith, D.; Smith, V. J.; Belyaev, A.; Brew, C.; Brown, R. M.; Calligaris, L.; Cieri, D.; Cockerill, D. J. A.; Coughlan, J. A.; Harder, K.; Harper, S.; Olaiya, E.; Petyt, D.; Shepherd-Themistocleous, C. H.; Thea, A.; Tomalin, I. R.; Williams, T.; Auzinger, G.; Bainbridge, R.; Borg, J.; Breeze, S.; Buchmuller, O.; Bundock, A.; Casasso, S.; Citron, M.; Colling, D.; Corpe, L.; Dauncey, P.; Davies, G.; De Wit, A.; Della Negra, M.; Di Maria, R.; Elwood, A.; Haddad, Y.; Hall, G.; Iles, G.; James, T.; Lane, R.; Laner, C.; Lyons, L.; Magnan, A.-M.; Malik, S.; Mastrolorenzo, L.; Matsushita, T.; Nash, J.; Nikitenko, A.; Palladino, V.; Pesaresi, M.; Raymond, D. M.; Richards, A.; Rose, A.; Scott, E.; Seez, C.; Shtipliyski, A.; Summers, S.; Tapper, A.; Uchida, K.; Vazquez Acosta, M.; Virdee, T.; Wardle, N.; Winterbottom, D.; Wright, J.; Zenz, S. C.; Cole, J. E.; Hobson, P. R.; Khan, A.; Kyberd, P.; Reid, I. D.; Symonds, P.; Teodorescu, L.; Turner, M.; Zahid, S.; Borzou, A.; Call, K.; Dittmann, J.; Hatakeyama, K.; Liu, H.; Pastika, N.; Smith, C.; Bartek, R.; Dominguez, A.; Buccilli, A.; Cooper, S. I.; Henderson, C.; Rumerio, P.; West, C.; Arcaro, D.; Avetisyan, A.; Bose, T.; Gastler, D.; Rankin, D.; Richardson, C.; Rohlf, J.; Sulak, L.; Zou, D.; Benelli, G.; Cutts, D.; Garabedian, A.; Hadley, M.; Hakala, J.; Heintz, U.; Hogan, J. M.; Kwok, K. H. M.; Laird, E.; Landsberg, G.; Lee, J.; Mao, Z.; Narain, M.; Pazzini, J.; Piperov, S.; Sagir, S.; Syarif, R.; Yu, D.; Band, R.; Brainerd, C.; Burns, D.; Calderon De La Barca Sanchez, M.; Chertok, M.; Conway, J.; Conway, R.; Cox, P. T.; Erbacher, R.; Flores, C.; Funk, G.; Gardner, M.; Ko, W.; Lander, R.; Mclean, C.; Mulhearn, M.; Pellett, D.; Pilot, J.; Shalhout, S.; Shi, M.; Smith, J.; Stolp, D.; Tos, K.; Tripathi, M.; Wang, Z.; Bachtis, M.; Bravo, C.; Cousins, R.; Dasgupta, A.; Florent, A.; Hauser, J.; Ignatenko, M.; Mccoll, N.; Regnard, S.; Saltzberg, D.; Schnaible, C.; Valuev, V.; Bouvier, E.; Burt, K.; Clare, R.; Ellison, J.; Gary, J. W.; Ghiasi Shirazi, S. M. A.; Hanson, G.; Heilman, J.; Kennedy, E.; Lacroix, F.; Long, O. R.; Olmedo Negrete, M.; Paneva, M. I.; Si, W.; Wang, L.; Wei, H.; Wimpenny, S.; Yates, B. R.; Branson, J. G.; Cittolin, S.; Derdzinski, M.; Gerosa, R.; Gilbert, D.; Hashemi, B.; Holzner, A.; Klein, D.; Kole, G.; Krutelyov, V.; Letts, J.; Macneill, I.; Masciovecchio, M.; Olivito, D.; Padhi, S.; Pieri, M.; Sani, M.; Sharma, V.; Simon, S.; Tadel, M.; Vartak, A.; Wasserbaech, S.; Wood, J.; Würthwein, F.; Yagil, A.; Zevi Della Porta, G.; Amin, N.; Bhandari, R.; Bradmiller-Feld, J.; Campagnari, C.; Dishaw, A.; Dutta, V.; Franco Sevilla, M.; George, C.; Golf, F.; Gouskos, L.; Gran, J.; Heller, R.; Incandela, J.; Ovcharova, A.; Qu, H.; Richman, J.; Stuart, D.; Suarez, I.; Yoo, J.; Anderson, D.; Bornheim, A.; Lawhorn, J. M.; Newman, H. B.; Nguyen, T.; Pena, C.; Spiropulu, M.; Vlimant, J. R.; Xie, S.; Zhang, Z.; Zhu, R. Y.; Andrews, M. B.; Ferguson, T.; Mudholkar, T.; Paulini, M.; Russ, J.; Sun, M.; Vogel, H.; Vorobiev, I.; Weinberg, M.; Cumalat, J. P.; Ford, W. T.; Jensen, F.; Johnson, A.; Krohn, M.; Leontsinis, S.; Mulholland, T.; Stenson, K.; Wagner, S. R.; Alexander, J.; Chaves, J.; Chu, J.; Dittmer, S.; Mcdermott, K.; Mirman, N.; Patterson, J. R.; Quach, D.; Rinkevicius, A.; Ryd, A.; Skinnari, L.; Soffi, L.; Tan, S. M.; Tao, Z.; Thom, J.; Tucker, J.; Wittich, P.; Zientek, M.; Abdullin, S.; Albrow, M.; Alyari, M.; Apollinari, G.; Apresyan, A.; Apyan, A.; Banerjee, S.; Bauerdick, L. A. T.; Beretvas, A.; Berryhill, J.; Bhat, P. C.; Bolla, G.; Burkett, K.; Butler, J. N.; Canepa, A.; Cerati, G. B.; Cheung, H. W. K.; Chlebana, F.; Cremonesi, M.; Duarte, J.; Elvira, V. D.; Freeman, J.; Gecse, Z.; Gottschalk, E.; Gray, L.; Green, D.; Grünendahl, S.; Gutsche, O.; Harris, R. M.; Hasegawa, S.; Hirschauer, J.; Hu, Z.; Jayatilaka, B.; Jindariani, S.; Johnson, M.; Joshi, U.; Klima, B.; Kreis, B.; Lammel, S.; Lincoln, D.; Lipton, R.; Liu, M.; Liu, T.; Lopes De Sá, R.; Lykken, J.; Maeshima, K.; Magini, N.; Marraffino, J. M.; Mason, D.; McBride, P.; Merkel, P.; Mrenna, S.; Nahn, S.; O'Dell, V.; Pedro, K.; Prokofyev, O.; Rakness, G.; Ristori, L.; Schneider, B.; Sexton-Kennedy, E.; Soha, A.; Spalding, W. J.; Spiegel, L.; Stoynev, S.; Strait, J.; Strobbe, N.; Taylor, L.; Tkaczyk, S.; Tran, N. V.; Uplegger, L.; Vaandering, E. W.; Vernieri, C.; Verzocchi, M.; Vidal, R.; Wang, M.; Weber, H. A.; Whitbeck, A.; Acosta, D.; Avery, P.; Bortignon, P.; Bourilkov, D.; Brinkerhoff, A.; Carnes, A.; Carver, M.; Curry, D.; Field, R. D.; Furic, I. K.; Gleyzer, S. V.; Joshi, B. M.; Konigsberg, J.; Korytov, A.; Kotov, K.; Ma, P.; Matchev, K.; Mei, H.; Mitselmakher, G.; Rank, D.; Shi, K.; Sperka, D.; Terentyev, N.; Thomas, L.; Wang, J.; Wang, S.; Yelton, J.; Joshi, Y. R.; Linn, S.; Markowitz, P.; Rodriguez, J. L.; Ackert, A.; Adams, T.; Askew, A.; Hagopian, S.; Hagopian, V.; Johnson, K. F.; Kolberg, T.; Martinez, G.; Perry, T.; Prosper, H.; Saha, A.; Santra, A.; Sharma, V.; Yohay, R.; Baarmand, M. M.; Bhopatkar, V.; Colafranceschi, S.; Hohlmann, M.; Noonan, D.; Roy, T.; Yumiceva, F.; Adams, M. R.; Apanasevich, L.; Berry, D.; Betts, R. R.; Cavanaugh, R.; Chen, X.; Evdokimov, O.; Gerber, C. E.; Hangal, D. A.; Hofman, D. J.; Jung, K.; Kamin, J.; Sandoval Gonzalez, I. D.; Tonjes, M. B.; Trauger, H.; Varelas, N.; Wang, H.; Wu, Z.; Zhang, J.; Bilki, B.; Clarida, W.; Dilsiz, K.; Durgut, S.; Gandrajula, R. P.; Haytmyradov, M.; Khristenko, V.; Merlo, J.-P.; Mermerkaya, H.; Mestvirishvili, A.; Moeller, A.; Nachtman, J.; Ogul, H.; Onel, Y.; Ozok, F.; Penzo, A.; Snyder, C.; Tiras, E.; Wetzel, J.; Yi, K.; Blumenfeld, B.; Cocoros, A.; Eminizer, N.; Fehling, D.; Feng, L.; Gritsan, A. V.; Maksimovic, P.; Roskes, J.; Sarica, U.; Swartz, M.; Xiao, M.; You, C.; Al-bataineh, A.; Baringer, P.; Bean, A.; Boren, S.; Bowen, J.; Castle, J.; Khalil, S.; Kropivnitskaya, A.; Majumder, D.; Mcbrayer, W.; Murray, M.; Royon, C.; Sanders, S.; Schmitz, E.; Tapia Takaki, J. D.; Wang, Q.; Ivanov, A.; Kaadze, K.; Maravin, Y.; Mohammadi, A.; Saini, L. K.; Skhirtladze, N.; Toda, S.; Rebassoo, F.; Wright, D.; Anelli, C.; Baden, A.; Baron, O.; Belloni, A.; Calvert, B.; Eno, S. C.; Feng, Y.; Ferraioli, C.; Hadley, N. J.; Jabeen, S.; Jeng, G. Y.; Kellogg, R. G.; Kunkle, J.; Mignerey, A. C.; Ricci-Tam, F.; Shin, Y. H.; Skuja, A.; Tonwar, S. C.; Abercrombie, D.; Allen, B.; Azzolini, V.; Barbieri, R.; Baty, A.; Bi, R.; Brandt, S.; Busza, W.; Cali, I. A.; D'Alfonso, M.; Demiragli, Z.; Gomez Ceballos, G.; Goncharov, M.; Hsu, D.; Hu, M.; Iiyama, Y.; Innocenti, G. M.; Klute, M.; Kovalskyi, D.; Lai, Y. S.; Lee, Y.-J.; Levin, A.; Luckey, P. D.; Maier, B.; Marini, A. C.; Mcginn, C.; Mironov, C.; Narayanan, S.; Niu, X.; Paus, C.; Roland, C.; Roland, G.; Salfeld-Nebgen, J.; Stephans, G. S. F.; Tatar, K.; Velicanu, D.; Wang, J.; Wang, T. W.; Wyslouch, B.; Benvenuti, A. C.; Chatterjee, R. M.; Evans, A.; Hansen, P.; Hiltbrand, J.; Kalafut, S.; Kubota, Y.; Lesko, Z.; Mans, J.; Nourbakhsh, S.; Ruckstuhl, N.; Rusack, R.; Turkewitz, J.; Wadud, M. A.; Acosta, J. G.; Oliveros, S.; Avdeeva, E.; Bloom, K.; Claes, D. R.; Fangmeier, C.; Gonzalez Suarez, R.; Kamalieddin, R.; Kravchenko, I.; Monroy, J.; Siado, J. E.; Snow, G. R.; Stieger, B.; Dolen, J.; Godshalk, A.; Harrington, C.; Iashvili, I.; Nguyen, D.; Parker, A.; Rappoccio, S.; Roozbahani, B.; Alverson, G.; Barberis, E.; Hortiangtham, A.; Massironi, A.; Morse, D. M.; Orimoto, T.; Teixeira De Lima, R.; Trocino, D.; Wood, D.; Bhattacharya, S.; Charaf, O.; Hahn, K. A.; Mucia, N.; Odell, N.; Pollack, B.; Schmitt, M. H.; Sung, K.; Trovato, M.; Velasco, M.; Dev, N.; Hildreth, M.; Hurtado Anampa, K.; Jessop, C.; Karmgard, D. J.; Kellams, N.; Lannon, K.; Loukas, N.; Marinelli, N.; Meng, F.; Mueller, C.; Musienko, Y.; Planer, M.; Reinsvold, A.; Ruchti, R.; Smith, G.; Taroni, S.; Wayne, M.; Wolf, M.; Woodard, A.; Alimena, J.; Antonelli, L.; Bylsma, B.; Durkin, L. S.; Flowers, S.; Francis, B.; Hart, A.; Hill, C.; Ji, W.; Liu, B.; Luo, W.; Winer, B. L.; Wulsin, H. W.; Cooperstein, S.; Driga, O.; Elmer, P.; Hardenbrook, J.; Hebda, P.; Higginbotham, S.; Lange, D.; Luo, J.; Marlow, D.; Mei, K.; Ojalvo, I.; Olsen, J.; Palmer, C.; Piroué, P.; Stickland, D.; Tully, C.; Malik, S.; Norberg, S.; Barker, A.; Barnes, V. E.; Das, S.; Folgueras, S.; Gutay, L.; Jha, M. K.; Jones, M.; Jung, A. W.; Khatiwada, A.; Miller, D. H.; Neumeister, N.; Peng, C. C.; Qiu, H.; Schulte, J. F.; Sun, J.; Wang, F.; Xie, W.; Cheng, T.; Parashar, N.; Stupak, J.; Adair, A.; Chen, Z.; Ecklund, K. M.; Freed, S.; Geurts, F. J. M.; Guilbaud, M.; Kilpatrick, M.; Li, W.; Michlin, B.; Northup, M.; Padley, B. P.; Roberts, J.; Rorie, J.; Shi, W.; Tu, Z.; Zabel, J.; Zhang, A.; Bodek, A.; de Barbaro, P.; Demina, R.; Duh, Y. t.; Ferbel, T.; Galanti, M.; Garcia-Bellido, A.; Han, J.; Hindrichs, O.; Khukhunaishvili, A.; Lo, K. H.; Tan, P.; Verzetti, M.; Ciesielski, R.; Goulianos, K.; Mesropian, C.; Agapitos, A.; Chou, J. P.; Gershtein, Y.; Gómez Espinosa, T. A.; Halkiadakis, E.; Heindl, M.; Hughes, E.; Kaplan, S.; Kunnawalkam Elayavalli, R.; Kyriacou, S.; Lath, A.; Montalvo, R.; Nash, K.; Osherson, M.; Saka, H.; Salur, S.; Schnetzer, S.; Sheffield, D.; Somalwar, S.; Stone, R.; Thomas, S.; Thomassen, P.; Walker, M.; Delannoy, A. G.; Foerster, M.; Heideman, J.; Riley, G.; Rose, K.; Spanier, S.; Thapa, K.; Bouhali, O.; Castaneda Hernandez, A.; Celik, A.; Dalchenko, M.; De Mattia, M.; Delgado, A.; Dildick, S.; Eusebi, R.; Gilmore, J.; Huang, T.; Kamon, T.; Mueller, R.; Pakhotin, Y.; Patel, R.; Perloff, A.; Perniè, L.; Rathjens, D.; Safonov, A.; Tatarinov, A.; Ulmer, K. A.; Akchurin, N.; Damgov, J.; De Guio, F.; Dudero, P. R.; Faulkner, J.; Gurpinar, E.; Kunori, S.; Lamichhane, K.; Lee, S. W.; Libeiro, T.; Mengke, T.; Muthumuni, S.; Peltola, T.; Undleeb, S.; Volobouev, I.; Wang, Z.; Greene, S.; Gurrola, A.; Janjam, R.; Johns, W.; Maguire, C.; Melo, A.; Ni, H.; Padeken, K.; Sheldon, P.; Tuo, S.; Velkovska, J.; Xu, Q.; Arenton, M. W.; Barria, P.; Cox, B.; Hirosky, R.; Joyce, M.; Ledovskoy, A.; Li, H.; Neu, C.; Sinthuprasith, T.; Wang, Y.; Wolfe, E.; Xia, F.; Harr, R.; Karchin, P. E.; Poudyal, N.; Sturdy, J.; Thapa, P.; Zaleski, S.; Brodski, M.; Buchanan, J.; Caillol, C.; Dasu, S.; Dodd, L.; Duric, S.; Gomber, B.; Grothe, M.; Herndon, M.; Hervé, A.; Hussain, U.; Klabbers, P.; Lanaro, A.; Levine, A.; Long, K.; Loveless, R.; Polese, G.; Ruggles, T.; Savin, A.; Smith, N.; Smith, W. H.; Taylor, D.; Woods, N.

2018-01-01

The pseudorapidity distributions of charged hadrons in proton-lead collisions at nucleon-nucleon center-of-mass energies √{s_{NN}}=5.02 and 8.16 TeV are presented. The measurements are based on data samples collected by the CMS experiment at the LHC. The number of primary charged hadrons produced in non-single-diffractive proton-lead collisions is determined in the pseudorapidity range | η lab| < 2 .4. The charged-hadron multiplicity distributions are compared to the predictions from theoretical calculations and Monte Carlo event generators. In the center-of-mass pseudorapidity range | η cm| < 0 .5, the average charged-hadron multiplicity densities 〈d N ch/d η cm〉| ηcm| < 0.5 are 17 .31 ± 0 .01 (stat) ± 0 .59 (syst) and 20 .10 ± 0 .01 (stat) ± 0 .85(syst) at √{s_{NN}}=5.02 and 8.16 TeV, respectively. The particle densities per participant nucleon are compared to similar measurements in proton-proton, proton-nucleus, and nucleus-nucleus collisions. [Figure not available: see fulltext.

Effect of hindlimb unloading on stereological parameters of the motor cortex and hippocampus in male rats.

PubMed

Salehi, Mohammad Saied; Mirzaii-Dizgah, Iraj; Vasaghi-Gharamaleki, Behnoosh; Zamiri, Mohammad Javad

2016-11-09

Hindlimb unloading (HU) can cause motion and cognition dysfunction, although its cellular and molecular mechanisms are not well understood. The aim of the present study was to determine the stereological parameters of the brain areas involved in motion (motor cortex) and spatial learning - memory (hippocampus) under an HU condition. Sixteen adult male rats, kept under a 12 : 12 h light-dark cycle, were divided into two groups of freely moving (n=8) and HU (n=8) rats. The volume of motor cortex and hippocampus, the numerical cell density of neurons in layers I, II-III, V, and VI of the motor cortex, the entire motor cortex as well as the primary motor cortex, and the numerical density of the CA1, CA3, and dentate gyrus subregions of the hippocampus were estimated. No significant differences were observed in the evaluated parameters. Our results thus indicated that motor cortical and hippocampal atrophy and cell loss may not necessarily be involved in the motion and spatial learning memory impairment in the rat.

Self-Assembly of Antisite Defectless nano-LiFePO4 @C/Reduced Graphene Oxide Microspheres for High-Performance Lithium-Ion Batteries.

PubMed

Wang, Hongbin; Liu, Lijia; Wang, Runwei; Yan, Xiao; Wang, Ziqi; Hu, Jiangtao; Chen, Haibiao; Jiang, Shang; Ni, Ling; Qiu, Hailong; Tang, Haitong; Wei, Yingjin; Zhang, Zongtao; Qiu, Shilun; Pan, Feng

2018-05-18

LiFePO 4 @C/reduced graphene oxide (rGO) hierarchical microspheres with superior electrochemical activity and a high tap density were first synthesized by using a Fe 3+ -based single inorganic precursor (LiFePO 4 OH@RF/GO; RF=resorcinol-formaldehyde, GO=graphene oxide) obtained from a template-free self-assembly synthesis followed by direct calcination. The synthetic process requires no physical mixing step. The phase transformation pathway from tavorite LiFePO 4 OH to olivine LiFePO 4 upon calcination was determined by means of the in situ high-temperature XRD technique. Benefitting from the unique structure of the material, these microspheres can be densely packed together, giving a high tap density of 1.3 g cm -3 , and simultaneously, defectless LiFePO 4 primary nanocrystals modified with a highly conductive surface carbon layer and ultrathin rGO provide good electronic and ionic kinetics for fast electron/Li + ion transport. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Lateral distributions of EAS muons (Eμ > 800 MeV) measured with the KASCADE-Grande Muon Tracking Detector in the primary energy range 1016 -1017 eV

NASA Astrophysics Data System (ADS)

Apel, W. D.; Arteaga-Velázquez, J. C.; Bekk, K.; Bertaina, M.; Blümer, J.; Bozdog, H.; Brancus, I. M.; Cantoni, E.; Chiavassa, A.; Cossavella, F.; Daumiller, K.; de Souza, V.; Di Pierro, F.; Doll, P.; Engel, R.; Engler, J.; Fuchs, B.; Fuhrmann, D.; Gherghel-Lascu, A.; Gils, H. J.; Glasstetter, R.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Huber, D.; Huege, T.; Kampert, K.-H.; Kang, D.; Klages, H. O.; Link, K.; Łuczak, P.; Mathes, H. J.; Mayer, H. J.; Milke, J.; Mitrica, B.; Morello, C.; Oehlschläger, J.; Ostapchenko, S.; Palmieri, N.; Petcu, M.; Pierog, T.; Rebel, H.; Roth, M.; Schieler, H.; Schoo, S.; Schröder, F. G.; Sima, O.; Toma, G.; Trinchero, G. C.; Ulrich, H.; Weindl, A.; Wochele, J.; Zabierowski, J.

2015-05-01

The KASCADE-Grande large area (128 m2) Muon Tracking Detector has been built with the aim to identify muons ( Eμthr = 800 MeV) in Extensive Air Showers by track measurements under 18 r.l. shielding. This detector provides high-accuracy angular information (approx. 0.3 °) for muons up to 700 m distance from the shower core. In this work we present the lateral density distributions of muons in EAS measured with the Muon Tracking Detector of the KASCADE-Grande experiment. The density is calculated by counting muon tracks in a muon-to-shower-axis distance range from 100 m to 610 m from showers with reconstructed energy of 1016 -1017 eV and zenith angle θ < 18 ° . In the distance range covered by the experiment, these distributions are well described by functions phenomenologically determined already in the fifties (of the last century) by Greisen. They are compared also with the distributions obtained with the KASCADE scintillator array (Eμthr = 230 MeV) and with distributions obtained using simulated showers.

Population and prehistory III: food-dependent demography in variable environments.

PubMed

Lee, Charlotte T; Puleston, Cedric O; Tuljapurkar, Shripad

2009-11-01

The population dynamics of preindustrial societies depend intimately on their surroundings, and food is a primary means through which environment influences population size and individual well-being. Food production requires labor; thus, dependence of survival and fertility on food involves dependence of a population's future on its current state. We use a perturbation approach to analyze the effects of random environmental variation on this nonlinear, age-structured system. We show that in expanding populations, direct environmental effects dominate induced population fluctuations, so environmental variability has little effect on mean hunger levels, although it does decrease population growth. The growth rate determines the time until population is limited by space. This limitation introduces a tradeoff between population density and well-being, so population effects become more important than the direct effects of the environment: environmental fluctuation increases mortality, releasing density dependence and raising average well-being for survivors. We discuss the social implications of these findings for the long-term fate of populations as they transition from expansion into limitation, given that conditions leading to high well-being during growth depress well-being during limitation.

Double-Q spin-density wave in iron arsenide superconductors

DOE PAGES

Allred, J. M.; Taddei, K. M.; Bugaris, D. E.; ...

2016-01-25

Elucidating the nature of the magnetic ground state of iron-based superconductors is of paramount importance in unveiling the mechanism behind their high temperature superconductivity. Until recently, it was thought that superconductivity emerges only from an orthorhombic antiferromagnetic stripe phase, which can in principle be described in terms of either localized or itinerant spins. However, we recently reported that tetragonal symmetry is restored inside the magnetically ordered state of certain hole-doped compounds, revealing the existence of a new magnetic phase at compositions close to the onset of superconductivity. Here, we present Mossbauer data that show that half of the iron sitesmore » in this tetragonal phase are non-magnetic, establishing conclusively the existence of a novel magnetic ground state with a non-uniform magnetization that is inconsistent with localized spins. Instead, this state is naturally explained as the interference between two commensurate spin density waves, a rare example of collinear double-Q magnetic order. Finally, our results demonstrate the itinerant character of the magnetism of the iron pnictides, and the primary role played by magnetic degrees of freedom in determining their phase diagram.« less

High-resolution measurements from the airborne Atmospheric Nitrogen Dioxide Imager (ANDI)

NASA Astrophysics Data System (ADS)

Lawrence, J. P.; Anand, J. S.; Vande Hey, J. D.; Leigh, R. R.; Monks, P. S.; Leigh, R. J.

2015-06-01

Nitrogen Dioxide is both a primary pollutant with direct health effects and a key precursor of the secondary pollutant ozone. This paper reports on the development, characterisation and test flight of the Atmospheric Nitrogen Dioxide Imager (ANDI) remote sensing system. The ANDI system includes an imaging (UV)-vis grating spectrometer able to capture scattered sunlight spectra for the determination of tropospheric nitrogen dioxide (NO2) concentrations by way of DOAS slant column density and vertical column density measurements. Results are shown for an ANDI test flight over Leicester City in the UK. Retrieved NO2 columns at a surface resolution of 80 m x 20 m revealed hot spots in a series of locations around Leicester City, including road junctions, the train station, major car parks, areas of heavy industry, a nearby airport (East Midlands) and a power station (Ratcliffe-on-Soar). In the city centre the dominant source of NO2 emissions was identified as road traffic, contributing to a background concentration as well as producing localised hot spots. Quantitative analysis revealed a significant urban increment over the city centre which increased throughout the flight.

Metrics of cellular and vascular infiltration of human acellular dermal matrix in ventral hernia repairs.

PubMed

Campbell, Kristin Turza; Burns, Nadja K; Ensor, Joe; Butler, Charles E

2012-04-01

Human acellular dermal matrix is used for ventral hernia repair, as it resists infection and remodels by means of surrounding tissue. However, the tissue source and impact of basement membrane on cell and vessel infiltration have not been determined. The authors hypothesized that musculofascia would be the primary tissue source of cells and vessels infiltrating into human acellular dermal matrix and that the basement membrane would inhibit infiltration. Fifty-six guinea pigs underwent inlay human acellular dermal matrix ventral hernia repair with the basement membrane oriented toward or away from the peritoneum. At postoperative weeks 1, 2, or 4, repair sites were completely excised. Histologic and immunohistochemical analyses were performed to quantify cell and vessel density within repair-site zones, including interface (lateral, beneath musculofascia) and center (beneath subcutaneous fat) zones. Cell and vessel quantities were compared as functions of zone, basement membrane orientation, and time. Cellular and vascular infiltration increased over time universally. The interface demonstrated greater mean cell density than the center (weeks 1 and 2, p = 0.01 and p < 0.0001, respectively). Cell density was greater with the basement membrane oriented toward the peritoneum at week 4 (p = 0.02). The interface zone had greater mean vessel density than the center zone at week 4 (p < 0.0001). Orienting the basement membrane toward the peritoneum increased vessel density at week 4 (p = 0.0004). Cellular and vascular infiltration into human acellular dermal matrix for ventral hernia repairs was greater from musculofascia than from subcutaneous fat, and the basement membrane inhibited cellular and vascular infiltration. Human acellular dermal matrix should be placed adjacent to the best vascularizing tissue to improve fibrovascular incorporation.

Temporal and basin-specific population trends of quagga mussels on soft sediment of a multi-basin reservoir

USGS Publications Warehouse

Caldwell, Timothy J; Rosen, Michael R.; Chandra, Sudeep; Acharya, Kumud; Caires, Andrea M; Davis, Clinton J.; Thaw, Melissa; Webster, Daniel M.

2015-01-01

Invasive quagga (Dreissena bugnesis) and zebra (Dreissena ploymorpha) mussels have rapidly spread throughout North America. Understanding the relationships between environmental variables and quagga mussels during the early stages of invasion will help management strategies and allow researchers to predict patterns of future invasions. Quagga mussels were detected in Lake Mead, NV/AZ in 2007, we monitored early invasion dynamics in 3 basins (Boulder Basin, Las Vegas Bay, Overton Arm) bi-annually from 2008-2011. Mean quagga density increased over time during the first year of monitoring and stabilized for the subsequent two years at the whole-lake scale (8 to 132 individuals·m-2, geometric mean), in Boulder Basin (73 to 875 individuals·m-2), and in Overton Arm(2 to 126 individuals·m-2). In Las Vegas Bay, quagga mussel density was low (9 to 44 individuals·m-2), which was correlated with high sediment metal concentrations and warmer (> 30°C) water temperatures associated with that basin. Carbon content in the sediment increased with depth in Lake Mead and during some sampling periods quagga density was also positively correlated with depth, but more research is required to determine the significance of this interaction. Laboratory growth experiments suggested that food quantity may limit quagga growth in Boulder Basin, indicating an opportunity for population expansion in this basin if primary productivity were to increase, but was not the case in Overton Arm. Overall quagga mussel density in Lake Mead is highly variable and patchy, suggesting that temperature, sediment size, and sediment metal concentrations, and sediment carbon content all contribute to mussel distribution patterns. Quagga mussel density in the soft sediment of Lake Mead expanded during initial colonization, and began to stabilize approximately 3 years after the initial invasion.

Improving the assessment of predator functional responses by considering alternate prey and predator interactions.

PubMed

Chan, K; Boutin, S; Hossie, T J; Krebs, C J; O'Donoghue, M; Murray, D L

2017-07-01

To improve understanding of the complex and variable patterns of predator foraging behavior in natural systems, it is critical to determine how density-dependent predation and predator hunting success are mediated by alternate prey or predator interference. Despite considerable theory and debate seeking to place predator-prey interactions in a more realistic context, few empirical studies have quantified the role of alternate prey or intraspecific interactions on predator-prey dynamics. We assessed functional responses of two similarly sized, sympatric carnivores, lynx (Lynx canadensis) and coyotes (Canis latrans), foraging on common primary (snowshoe hares; Lepus americanus) and alternate (red squirrels; Tamiasciurus hudsonicus) prey in a natural system. Lynx exhibited a hyperbolic prey-dependent response to changes in hare density, which is characteristic of predators relying primarily on a single prey species. In contrast, the lynx-squirrel response was found to be linear ratio dependent, or inversely dependent on hare density. The coyote-hare and coyote-squirrel interactions also were linear and influenced by predator density. We explain these novel results by apparent use of spatial and temporal refuges by prey, and the likelihood that predators commonly experience interference and lack of satiation when foraging. Our study provides empirical support from a natural predator-prey system that (1) predation rate may not be limited at high prey densities when prey are small or rarely captured; (2) interference competition may influence the predator functional response; and (3) predator interference has a variable role across different prey types. Ultimately, distinct functional responses of predators to different prey types illustrates the complexity associated with predator-prey interactions in natural systems and highlights the need to investigate predator behavior and predation rate in relation to the broader ecological community. © 2017 by the Ecological Society of America.

Do the venous blood samples replicate malaria parasite densities found in capillary blood? A field study performed in naturally-infected asymptomatic children in Cameroon.

PubMed

Sandeu, Maurice M; Bayibéki, Albert N; Tchioffo, Majoline T; Abate, Luc; Gimonneau, Geoffrey; Awono-Ambéné, Parfait H; Nsango, Sandrine E; Diallo, Diadier; Berry, Antoine; Texier, Gaétan; Morlais, Isabelle

2017-08-17

The measure of new drug- or vaccine-based approaches for malaria control is based on direct membrane feeding assays (DMFAs) where gametocyte-infected blood samples are offered to mosquitoes through an artificial feeder system. Gametocyte donors are identified by the microscopic detection and quantification of malaria blood stages on blood films prepared using either capillary or venous blood. However, parasites are known to sequester in the microvasculature and this phenomenon may alter accurate detection of parasites in blood films. The blood source may then impact the success of mosquito feeding experiments and investigations are needed for the implementation of DMFAs under natural conditions. Thick blood smears were prepared from blood obtained from asymptomatic children attending primary schools in the vicinity of Mfou (Cameroon) over four transmission seasons. Parasite densities were determined microscopically from capillary and venous blood for 137 naturally-infected gametocyte carriers. The effect of the blood source on gametocyte and asexual stage densities was then assessed by fitting cumulative link mixed models (CLMM). DMFAs were performed to compare the infectiousness of gametocytes from the different blood sources to mosquitoes. Prevalence of Plasmodium falciparum asexual stages among asymptomatic children aged from 4 to 15 years was 51.8% (2116/4087). The overall prevalence of P. falciparum gametocyte carriage was 8.9% and varied from one school to another. No difference in the density of gametocyte and asexual stages was found between capillary and venous blood. Attempts to perform DMFAs with capillary blood failed. Plasmodium falciparum malaria parasite densities do not differ between capillary and venous blood in asymptomatic subjects for both gametocyte and trophozoite stages. This finding suggests that the blood source should not interfere with transmission efficiency in DMFAs.

IBEX-lo Sky Maps of Secondary Interstellar Neutrals Helium and Oxygen

NASA Astrophysics Data System (ADS)

Kucharek, H.; Isenberg, P. A.; Jeewoo, P.; Kubiak, M. A.; Bzowski, M.

2017-12-01

There are several populations of heliospheric energetic neutral atoms (ENAs) generated at the various heliospheric interfaces, the inner heliosheath, outer heliosheath (OHS), and the termination shock (TS). Depending on where and how these ENAs are generated, they belong to different energy regimes. While interstellar neutral (ISN) particles flow through the heliospheric boundary is mostly unimpeded, a substantial fraction of ISN H and O is filtered through charge exchange with ambient plasma ions before reaching the TS. Secondary ISN atoms are generated by the charge exchange reaction between primary ISN atoms and interstellar ions in the outer heliosheath, forming walls of H and O in front of the heliopause (HP). The flowing interstellar plasma encounters the heliopause as an obstacle, which deflects the flow. Thus, secondary neutrals measured at 1 AU carry information about the deflected interstellar plasma and the shape of the heliopause that causes the deflection. Due to very different magnitudes of charge exchange cross sections, the main source of the secondary He is charge exchange with the OHS He+, while that of the secondary O is the charge exchange between interstellar O+ and the OHS H. Therefore, the oxygen results are drastically different from those of helium. Interstellar O+ ions behave in principle like the He+ particles with an over-density due to the plasma deceleration. The high density decelerated oxygen ions just upwind of the heliopause encounter an over-density in neutral hydrogen, the hydrogen wall, allowing frequent charge exchange that produce slow neutral oxygen atoms forming the oxygen wall. Thus, the distribution in the sky maps of secondary He and O carries information on the shape as well as the structures in front of it. To investigate the secondary component of the interstellar neutral in detail we have distinguish between the two secondary component's. We engaged theory and simulations for the primary and secondary components to determine differences of between measurements and model predicted data.

The Relation of Growth to Stand Density in Natural Loblolly Pine Stands

Treesearch

K.F. Wenger; T.C. Evans; T. Lotti; R.W. Cooper; E.V. Brender

1958-01-01

This is a progress report of a regional study on growing-space requirements for natural stands of loblolly pine (Pinus taeda L.).A primary objective is to measure the effects of residual stand density, obtained naturally or by cutting, during intermediate ages, upon volume yield and total production. By imposing real values and costs upon...

KASCADE-Grande energy reconstruction based on the lateral density distribution using the QGSJet-II.04 interaction model

NASA Astrophysics Data System (ADS)

Gherghel-Lascu, A.; Apel, W. D.; Arteaga-Velázquez, J. C.; Bekk, K.; Bertania, M.; Blümer, J.; Bozdog, H.; Brancus, I. M.; Cantoni, E.; Chiavassa, A.; Cossavella, F.; Daumiller, K.; de Souza, V.; Di Pierro, F.; Doll, P.; Engel, R.; Fuhrmann, D.; Gils, H. J.; Glasstetter, R.; Grupen, C.; Haungs, A.; Heck, D.; Hörandel, J. R.; Huber, D.; Huege, T.; Kampert, K.-H.; Kang, D.; Klages, H. O.; Link, K.; Łuczak, P.; Mathes, H. J.; Mayer, H. J.; Milke, J.; Mitrica, B.; Morello, C.; Oehlschläger, J.; Ostapchenko, S.; Palmieri, N.; Pierog, T.; Rebel, H.; Roth, M.; Schieler, H.; Schoo, S.; Schröder, F. G.; Sima, O.; Toma, G.; Trinchero, G. C.; Ulrich, H.; Weindl, A.; Wochele, J.; Zabierowski, J.

2017-06-01

The charged particle densities obtained from CORSIKA simulated EAS, using the QGSJet-II.04 hadronic interaction model are used for primary energy reconstruction. Simulated data are reconstructed by using Lateral Energy Correction Functions computed with a new realistic model of the Grande stations implemented in Geant4.10.

Rosuvastatin enhances the catabolism of LDL apoB-100 in subjects with combined hyperlipidemia in a dose dependent manner

USDA-ARS?s Scientific Manuscript database

Dose-associated effects of rosuvastatin on the metabolism of apolipoprotein (apo) B-100 in triacylglycerol rich lipoprotein (TRL, d < 1.019 g/ml) and low density lipoprotein (LDL) and of apoA-I in high density lipoprotein (HDL) were assessed in subjects with combined hyperlipidemia. Our primary hypo...

Exposure of Children to Ultrafine Particles in Primary Schools in Portugal.

PubMed

Rufo, João Cavaleiro; Madureira, Joana; Paciência, Inês; Slezakova, Klara; Pereira, Maria do Carmo; Pereira, Cristiana; Teixeira, João Paulo; Pinto, Mariana; Moreira, André; Fernandes, Eduardo de Oliveira

2015-01-01

Children spend a large part of their time at schools, which might be reflected as chronic exposure. Ultrafine particles (UFP) are generally associated with a more severe toxicity compared to fine and coarse particles, due to their ability to penetrate cell membranes. In addition, children tend to be more susceptible to UFP-mediated toxicity compared to adults, due to various factors including undeveloped immune and respiratory systems and inhalation rates. Thus, the purpose of this study was to determine indoor UFP number concentrations in Portuguese primary schools. Ultrafine particles were sampled between January and March 2014 in 10 public primary schools (35 classrooms) located in Porto, Portugal. Overall, the average indoor UFP number concentrations were not significantly different from outdoor concentrations (8.69 × 10(3) vs. 9.25 × 10(3) pt/cm(3), respectively; considering 6.5 h of indoor occupancy). Classrooms with distinct characteristics showed different trends of indoor UFP concentrations. The levels of carbon dioxide were negatively correlated with indoor UFP concentrations. Occupational density was significantly and positively correlated with UFP concentrations. Although the obtained results need to be interpreted with caution since there are no guidelines for UFP levels, special attention needs to be given to source control strategies in order to reduce major particle emissions and ensure good indoor air quality.

Conspicuous impacts of inconspicuous hosts on the Lyme disease epidemic.

PubMed

Brisson, Dustin; Dykhuizen, Daniel E; Ostfeld, Richard S

2008-01-22

Emerging zoonotic pathogens are a constant threat to human health throughout the world. Control strategies to protect public health regularly fail, due in part to the tendency to focus on a single host species assumed to be the primary reservoir for a pathogen. Here, we present evidence that a diverse set of species can play an important role in determining disease risk to humans using Lyme disease as a model. Host-targeted public health strategies to control the Lyme disease epidemic in North America have focused on interrupting Borrelia burgdorferi sensu stricto (ss) transmission between blacklegged ticks and the putative dominant reservoir species, white-footed mice. However, B. burgdorferi ss infects more than a dozen vertebrate species, any of which could transmit the pathogen to feeding ticks and increase the density of infected ticks and Lyme disease risk. Using genetic and ecological data, we demonstrate that mice are neither the primary host for ticks nor the primary reservoir for B. burgdorferi ss, feeding 10% of all ticks and 25% of B. burgdorferi-infected ticks. Inconspicuous shrews feed 35% of all ticks and 55% of infected ticks. Because several important host species influence Lyme disease risk, interventions directed at a multiple host species will be required to control this epidemic.

Determining density of maize canopy. 1: Digitized photography

NASA Technical Reports Server (NTRS)

Stoner, E. R.; Baumgardner, M. F.; Swain, P. H.

1972-01-01

The relationship between different densities of maize (Zea mays L.) canopies and the energy reflected by these canopies was studied. Field plots were laid out, representing four growth stages of maize, on a dark soil and on a very light colored surface soil. Spectral and spatial data were obtained from color and color infrared photography taken from a vertical distance of 10 m above the maize canopies. Estimates of ground cover were related to field measurements of leaf area index. Ground cover was predicted from leaf area index measurements by a second order equation. Color infrared photography proved helpful in determining the density of maize canopy on dark soils. Color photography was useful for determining canopy density on light colored soils. The near infrared dye layer is the most valuable in canopy density determinations.

Handling Density Conversion in TPS.

PubMed

Isobe, Tomonori; Mori, Yutaro; Takei, Hideyuki; Sato, Eisuke; Tadano, Kiichi; Kobayashi, Daisuke; Tomita, Tetsuya; Sakae, Takeji

2016-01-01

Conversion from CT value to density is essential to a radiation treatment planning system. Generally CT value is converted to the electron density in photon therapy. In the energy range of therapeutic photon, interactions between photons and materials are dominated with Compton scattering which the cross-section depends on the electron density. The dose distribution is obtained by calculating TERMA and kernel using electron density where TERMA is the energy transferred from primary photons and kernel is a volume considering spread electrons. Recently, a new method was introduced which uses the physical density. This method is expected to be faster and more accurate than that using the electron density. As for particle therapy, dose can be calculated with CT-to-stopping power conversion since the stopping power depends on the electron density. CT-to-stopping power conversion table is also called as CT-to-water-equivalent range and is an essential concept for the particle therapy.

SDSS-IV MaNGA: What Shapes the Distribution of Metals in Galaxies? Exploring the Roles of the Local Gas Fraction and Escape Velocity

NASA Astrophysics Data System (ADS)

Barrera-Ballesteros, J. K.; Heckman, T.; Sánchez, S. F.; Zakamska, N. L.; Cleary, J.; Zhu, G.; Brinkmann, J.; Drory, N.; THE MaNGA TEAM

2018-01-01

We determine the local metallicity of the ionized gas for more than 9.2 × 105 star-forming regions (spaxels) located in 1023 nearby galaxies included in the Sloan Digital Sky Survey-IV MaNGA integral field spectroscopy unit survey. We use the dust extinction derived from the Balmer decrement and the stellar template fitting in each spaxel to estimate the local gas and stellar mass densities, respectively. We also use the measured rotation curves to determine the local escape velocity (V esc). We then analyze the relationships between the local metallicity and both the local gas fraction (μ) and V esc. We find that metallicity decreases with both increasing μ and decreasing V esc. By examining the residuals in these relations we show that the gas fraction plays a more primary role in the local chemical enrichment than does V esc. We show that the gas-regulator model of chemical evolution provides a reasonable explanation of the metallicity on local scales. The best-fit parameters for this model are consistent with the metal loss caused by momentum-driven galactic outflows. We also argue that both the gas fraction and the local escape velocity are connected to the local stellar surface density, which in turn is a tracer of the epoch at which the dominant local stellar population formed.

A case report of osteomalacia unmasking primary biliary cirrhosis.

PubMed

Pawlowska, M; Kapeluto, J E; Kendler, D L

2015-07-01

Osteomalacia, a metabolic bone disease characterized by the inability to mineralize new osteoid, can be caused by vitamin D deficiency. We report a patient with symptomatic, biochemical, and imaging evidence of osteomalacia due to vitamin D deficiency, who as a result of work up for bone disease was diagnosed with early primary biliary cirrhosis. Osteomalacia was treated with high-dose vitamin D and serial bone density scans showed evidence of increasing bone mineral density suggesting osteoid mineralization in response to treatment. The diagnosis of cholestatic liver disease should be considered in all patients presenting with osteomalacia due to vitamin D deficiency, particularly if other cholestatic liver enzymes are elevated in addition to alkaline phosphatase.

BOOK REVIEW: Practical Density Measurement and Hydrometry

NASA Astrophysics Data System (ADS)

Gupta, S. V.

2003-01-01

Density determinations are very important not only for science and production but also in everyday life, since very often a product is sold by mass but the content of the package is measured by volume (or vice versa) so that the density is needed to convert the values. In production processes the density serves as a measure of mixing ratios and other properties. In science, the determination of Avogadro's constant using silicon single crystals and the potential replacement of the kilogram prototype boost density determination to an extremely low relative uncertainty of 10-7 or less. The book by S V Gupta explains in detail the foundations of any density measurement, namely the volume determination of solid artefacts in terms of the SI base unit of length and the density of water and mercury. Both the history and the actual state of science are reported. For practical density measurements, these chapters contain very useful formulae and tables. Water is treated in detail since it is most widely used as a standard not only for density determination but also to gravimetrically calibrate the capacity of volumetric glassware. Two thirds of the book are devoted to the practical density measurement of solids and liquids, mainly using classical instruments like pycnometers and hydrometers. Methods using free flotation of samples in a liquid without suspension are especially useful for small samples. Also, density determinations of powders and granular or porous samples are explained. Unfortunately, modern density meters of the oscillation type are dealt with in only a few pages. The book is clearly written and easy to understand. It contains a lot of evaluations of formulae that for practical measurements are represented in detailed tables. Methods and measurement procedures are described in detail, including also the calculation of uncertainty. Listings of the advantages and disadvantages of the different methods are very helpful. S V Gupta has written a book that will be a great help for scientists, students and practitioners. The book fills a gap since there is no modern book that describes density measurements and hydrometry in such detail. Horst Bettin

Alternative communication network designs for an operational Plato 4 CAI system

NASA Technical Reports Server (NTRS)

Mobley, R. E., Jr.; Eastwood, L. F., Jr.

1975-01-01

The cost of alternative communications networks for the dissemination of PLATO IV computer-aided instruction (CAI) was studied. Four communication techniques are compared: leased telephone lines, satellite communication, UHF TV, and low-power microwave radio. For each network design, costs per student contact hour are computed. These costs are derived as functions of student population density, a parameter which can be calculated from census data for one potential market for CAI, the public primary and secondary schools. Calculating costs in this way allows one to determine which of the four communications alternatives can serve this market least expensively for any given area in the U.S. The analysis indicates that radio distribution techniques are cost optimum over a wide range of conditions.

Timber Resources Inventory and Monitoring Joint Research Project

NASA Technical Reports Server (NTRS)

Hill, C. L.

1985-01-01

Primary objectives were to develop remote sensing analysis techniques for extracting forest related information from LANDSAT Multispectral Scanner (MMS) and Thematic Mapper data and to determine the extent to which International Paper Company information needs can be addressed with remote sensing information. The company actively manages 8.4 million acres of forest land. Traditionally, their forest inventories, updated on a three year cycle, are conducted through field surveys and aerial photography. The results reside in a digital forest data base containing 240 descriptive parameteres for individual forest stands. The information in the data base is used to develop seasonal and long range management strategies. Forest stand condition assessements (species composition, age, and density stratification) and identification of silvicultural activities (site preparation, planting, thinning, and harvest) are addressed.

Spectral irradiance calibration in the infrared. I - Ground-based and IRAS broadband calibrations

NASA Technical Reports Server (NTRS)

Cohen, Martin; Walker, Russell G.; Barlow, Michael J.; Deacon, John R.

1992-01-01

Absolutely calibrated versions of realistic model atmosphere calculations for Sirius and Vega by Kurucz (1991) are presented and used as a basis to offer a new absolute calibration of infrared broad and narrow filters. In-band fluxes for Vega are obtained and defined to be zero magnitude at all wavelengths shortward of 20 microns. Existing infrared photometry is used differentially to establish an absolute scale of the new Sirius model, yielding an angular diameter within 1 sigma of the mean determined interferometrically by Hanbury Brown et al. (1974). The use of Sirius as a primary infrared stellar standard beyond the 20 micron region is suggested. Isophotal wavelengths and monochromatic flux densities for both Vega and Sirius are tabulated.

New Method for Determining the Relative Stand Density of Forest Inventory Plots

Treesearch

Christopher W. Woodall; Patrick D. Miles

2006-01-01

Determining the relative density of Forest Inventory and Analysis plots is complicated by the various species and tree size combinations in the Nation?s forested ecosystems. Stand density index (SDI), although developed for use in even-aged monocultures, has been used for stand density assessment in largescale forest inventories. To improve application of SDI in uneven...

Product suitability of wood...determined by density gradients across growth rings

Treesearch

Robert M. Echols

1972-01-01

The suitability of wood for various uses can be determined by synthesizing single growth-ring density curves from accumulated means of wood density classes. Wood density gradients across growth rings were measured in large increment cores from 46-year-old ponderosa pines (Pinus ponderosa Laws.) by using X-rays. Of the 48 trees analyzed, 36 had been...

Uronide Deposition Rates in the Primary Root of Zea mays1

PubMed Central

Silk, Wendy Kuhn; Walker, Robert C.; Labavitch, John

1984-01-01

The spatial distribution of the rate of deposition of uronic acids in the elongation zone of Zea mays L. Crow WF9 × Mo 17 was determined using the continuity equation with experimentally determined values for uronide density and growth velocity. In spatial terms, the uronide deposition rate has a maximum of 0.4 micrograms per millimeter per hour at s = 3.5 mm (i.e., at the location 3.5 mm from the root tip) and decreases to 0.1 mg mm−1 h−1 by s = 10 mm. In terms of a material tissue element, a tissue segment located initially from s = 2.0 to s = 2.1 mm has 0.14 μg of uronic acids and increases in both length and uronic acid content until it is 0.9 mm long and has 0.7 μg of uronide when its center is at s = 10 mm. Simulations of radioactive labeling experiments show that 15 min is the appropriate time scale for pulse determinations of deposition rate profiles in a rapidly growing corn root. PMID:16663488

Effects of Irrigation and Rainfall on the Population Dynamics of Rift Valley Fever and Other Arbovirus Mosquito Vectors in the Epidemic-Prone Tana River County, Kenya.

PubMed

Sang, R; Lutomiah, J; Said, M; Makio, A; Koka, H; Koskei, E; Nyunja, A; Owaka, S; Matoke-Muhia, D; Bukachi, S; Lindahl, J; Grace, D; Bett, B

2017-03-01

Rift Valley fever (RVF) is a mosquito-borne viral zoonosis that is found in most regions of sub-Saharan Africa, and it affects humans, livestock, and some wild ungulates. Outbreaks are precipitated by an abundance of mosquito vectors associated with heavy persistent rainfall with flooding. We determined the impact of flood-irrigation farming and the effect of environmental parameters on the ecology and densities of primary and secondary vectors of the RVF virus (RVFV) in an RVF-epidemic hotspot in the Tana River Basin, Kenya. Mosquito sampling was conducted in farms and villages (settlements) in an irrigated and a neighboring nonirrigated site (Murukani). Overall, a significantly higher number of mosquitoes were collected in farms in the irrigation scheme compared with villages in the same area (P < 0.001), or farms (P < 0.001), and villages (P = 0.03) in Murukani. In particular, key primary vectors of RVFV, Aedes mcintoshi Marks and Aedes ochraceous Theobald, were more prevalent in the farms compared with villages in the irrigation scheme (P = 0.001) both during the dry and the wet seasons. Similarly, there was a greater abundance of secondary vectors, particularly Culex univittatus Theobald and Culex pipiens (L.) in the irrigation scheme than in the Murukani area. Rainfall and humidity were positively correlated with mosquito densities, particularly the primary vectors. Adult floodwater mosquitoes and Mansonia spp. were collected indoors; immatures of Ae. mcintoshi and secondary vectors were collected in the irrigation drainage canals, whereas those of Ae. ochraceous and Aedes sudanensis Theobald were missing from these water bodies. In conclusion, irrigation in RVF endemic areas provides conducive resting and breeding conditions for vectors of RVFV and other endemic arboviruses. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America.

Translating Cholesterol Guidelines Into Primary Care Practice: A Multimodal Cluster Randomized Trial

PubMed Central

Eaton, Charles B.; Parker, Donna R.; Borkan, Jeffrey; McMurray, Jerome; Roberts, Mary B.; Lu, Bing; Goldman, Roberta; Ahern, David K.

2011-01-01

PURPOSE We wanted to determine whether an intervention based on patient activation and a physician decision support tool was more effective than usual care for improving adherence to National Cholesterol Education Program guidelines. METHODS A 1-year cluster randomized controlled trial was performed using 30 primary care practices (4,105 patients) in southeastern New England. The main outcome was the percentage of patients screened for hyperlipidemia and treated to their low-density lipoprotein (LDL) and non–high-density lipoprotein (HDL) cholesterol goals. RESULTS After 1 year of intervention, both randomized practice groups improved screening (89% screened), and 74% of patients in both groups were at their LDL and non-HDL cholesterol goals (P <.001). Using intent-to-treat analysis, we found no statistically significant differences between practice groups in screening or percentage of patients who achieved LDL and non-HDL cholesterol goals. Post hoc analysis showed practices who made high use of the patient activation kiosk were more likely to have patients screened (odds ratio [OR] = 2.54; 95% confidence interval [CI], 1.97–3.27) compared with those who made infrequent or no use. Additionally, physicians who made high use of decision support tools were more likely to have their patients at their LDL cholesterol goals (OR = 1.27; 95% CI, 1.07–1.50) and non-HDL goals (OR = 1.23; 95% CI, 1.04–1.46) than low-use or no-use physicians. CONCLUSION This study showed null results with the intent-to-treat analysis regarding the benefits of a patient activation and a decision support tool in improving cholesterol management in primary care practices. Post hoc analysis showed a potential benefit in practices that used the e-health tools more frequently in screening and management of dyslipidemia. Further research on how to incorporate and increase adoption of user-friendly, patient-centered e-health tools to improve screening and management of chronic diseases and their risk factors is warranted. PMID:22084264

Structural, electronic and optical properties of well-known primary explosive: Mercury fulminate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yedukondalu, N.; Vaitheeswaran, G., E-mail: gvsp@uohyd.ernet.in

2015-11-28

Mercury Fulminate (MF) is one of the well-known primary explosives since 17th century and it has rendered invaluable service over many years. However, the correct molecular and crystal structures are determined recently after 300 years of its discovery. In the present study, we report pressure dependent structural, elastic, electronic and optical properties of MF. Non-local correction methods have been employed to capture the weak van der Waals interactions in layered and molecular energetic MF. Among the non-local correction methods tested, optB88-vdW method works well for the investigated compound. The obtained equilibrium bulk modulus reveals that MF is softer than themore » well known primary explosives Silver Fulminate (SF), silver azide and lead azide. MF exhibits anisotropic compressibility (b > a > c) under pressure, consequently the corresponding elastic moduli decrease in the following order: C{sub 22} > C{sub 11} > C{sub 33}. The structural and mechanical properties suggest that MF is more sensitive to detonate along c-axis (similar to RDX) due to high compressibility of Hg⋯O non-bonded interactions along that axis. Electronic structure and optical properties were calculated including spin-orbit (SO) interactions using full potential linearized augmented plane wave method within recently developed Tran-Blaha modified Becke-Johnson (TB-mBJ) potential. The calculated TB-mBJ electronic structures of SF and MF show that these compounds are indirect bandgap insulators. Also, SO coupling is found to be more pronounced for 4d and 5d-states of Ag and Hg atoms of SF and MF, respectively. Partial density of states and electron charge density maps were used to describe the nature of chemical bonding. Ag—C bond is more directional than Hg—C bond which makes SF to be more unstable than MF. The effect of SO coupling on optical properties has also been studied and found to be significant for both (SF and MF) of the compounds.« less

Evacetrapib and Cardiovascular Outcomes in High-Risk Vascular Disease.

PubMed

Lincoff, A Michael; Nicholls, Stephen J; Riesmeyer, Jeffrey S; Barter, Philip J; Brewer, H Bryan; Fox, Keith A A; Gibson, C Michael; Granger, Christopher; Menon, Venu; Montalescot, Gilles; Rader, Daniel; Tall, Alan R; McErlean, Ellen; Wolski, Kathy; Ruotolo, Giacomo; Vangerow, Burkhard; Weerakkody, Govinda; Goodman, Shaun G; Conde, Diego; McGuire, Darren K; Nicolau, Jose C; Leiva-Pons, Jose L; Pesant, Yves; Li, Weimin; Kandath, David; Kouz, Simon; Tahirkheli, Naeem; Mason, Denise; Nissen, Steven E

2017-05-18

The cholesteryl ester transfer protein inhibitor evacetrapib substantially raises the high-density lipoprotein (HDL) cholesterol level, reduces the low-density lipoprotein (LDL) cholesterol level, and enhances cellular cholesterol efflux capacity. We sought to determine the effect of evacetrapib on major adverse cardiovascular outcomes in patients with high-risk vascular disease. In a multicenter, randomized, double-blind, placebo-controlled phase 3 trial, we enrolled 12,092 patients who had at least one of the following conditions: an acute coronary syndrome within the previous 30 to 365 days, cerebrovascular atherosclerotic disease, peripheral vascular arterial disease, or diabetes mellitus with coronary artery disease. Patients were randomly assigned to receive either evacetrapib at a dose of 130 mg or matching placebo, administered daily, in addition to standard medical therapy. The primary efficacy end point was the first occurrence of any component of the composite of death from cardiovascular causes, myocardial infarction, stroke, coronary revascularization, or hospitalization for unstable angina. At 3 months, a 31.1% decrease in the mean LDL cholesterol level was observed with evacetrapib versus a 6.0% increase with placebo, and a 133.2% increase in the mean HDL cholesterol level was seen with evacetrapib versus a 1.6% increase with placebo. After 1363 of the planned 1670 primary end-point events had occurred, the data and safety monitoring board recommended that the trial be terminated early because of a lack of efficacy. After a median of 26 months of evacetrapib or placebo, a primary end-point event occurred in 12.9% of the patients in the evacetrapib group and in 12.8% of those in the placebo group (hazard ratio, 1.01; 95% confidence interval, 0.91 to 1.11; P=0.91). Although the cholesteryl ester transfer protein inhibitor evacetrapib had favorable effects on established lipid biomarkers, treatment with evacetrapib did not result in a lower rate of cardiovascular events than placebo among patients with high-risk vascular disease. (Funded by Eli Lilly; ACCELERATE ClinicalTrials.gov number, NCT01687998 .).

A direct determination of the gluon density in the proton at low x

NASA Astrophysics Data System (ADS)

Aid, S.; Andreev, V.; Andrieu, B.; Appuhn, R.-D.; Arpagaus, M.; Babaev, A.; Bähr, J.; Bán, J.; Ban, Y.; Baranov, P.; Barrelet, E.; Barschke, R.; Bartel, W.; Barth, M.; Bassler, U.; Beck, H. P.; Behrend, H.-J.; Belousov, A.; Berger, Ch.; Bernardi, G.; Bernet, R.; Bertrand-Coremans, G.; Besançon, M.; Beyer, R.; Biddulph, P.; Bispham, P.; Bizot, J. C.; Blobel, V.; Borras, K.; Botterweck, F.; Boudry, V.; Braemer, A.; Brasse, F.; Braunschweig, W.; Brisson, V.; Bruncko, D.; Brune, C.; Buchholz, R.; Büngener, L.; Bürger, J.; Büsser, F. W.; Buniatian, A.; Burke, S.; Burton, M. J.; Buschhorn, G.; Campbell, A. J.; Carli, T.; Charles, F.; Charlet, M.; Clarke, D.; Clegg, A. B.; Clerbaux, B.; Colombo, M.; Contreras, J. G.; Cormack, C.; Coughlan, J. A.; Courau, A.; Coutures, Ch.; Cozzika, G.; Criegee, L.; Cussans, D. G.; Cvach, J.; Dagoret, S.; Dainton, J. B.; Dau, W. D.; Daum, K.; David, M.; Delcourt, B.; Del Buono, L.; De Roeck, A.; De Wolf, E. A.; Di Nezza, P.; Dollfus, C.; Dowell, J. D.; Dreis, H. B.; Droutskoi, A.; Duboc, J.; Düllmann, D.; Dünger, O.; Duhm, H.; Ebert, J.; Ebert, T. R.; Eckerlin, G.; Efremenko, V.; Egli, S.; Ehrlichmann, H.; Eichenberger, S.; Eichler, R.; Eisele, F.; Eisenhandler, E.; Ellison, R. J.; Elsen, E.; Erdmann, M.; Erdmann, W.; Evrard, E.; Favart, L.; Fedotox, A.; Feeken, D.; Felst, R.; Feltesse, J.; Ferencei, J.; Ferrarotto, F.; Flamm, K.; Fleischer, M.; Flieser, M.; Flügge, G.; Fomenko, A.; Fominykh, B.; Forbush, M.; Formánek, J.; Foster, J. M.; Franke, G.; Fretwurst, E.; Gabathuler, E.; Gabathuler, K.; Garvey, J.; Gayler, J.; Gebauer, M.; Gellrich, A.; Genzel, H.; Gerhards, R.; Glazov, A.; Goerlach, U.; Goerlich, L.; Gogitidze, N.; Goldberg, M.; Goldner, D.; Gonzalez-Pineiro, B.; Gorelov, I.; Goritchev, P.; Grab, C.; Grässler, H.; Grässler, R.; Greenshaw, T.; Grindhammer, G.; Gruber, A.; Gruber, C.; Haack, J.; Haidt, D.; Hajduk, L.; Hamon, O.; Hampel, M.; Hapke, M.; Haynes, W. J.; Heatherington, J.; Heinzelmann, G.; Henderson, R. C. W.; Henschel, H.; Herynek, I.; Hess, M. F.; Hildesheim, W.; Hill, P.; Hiller, K. H.; Hilton, C. D.; Hladký, J.; Hoeger, K. C.; Höppner, M.; Horisberger, R.; Hudgson, V. L.; Huet, Ph.; Hütte, M.; Hufnagel, H.; Ibbotson, M.; Itterbeck, H.; Jabiol, M.-A.; Jacholkowska, A.; Jacobsson, C.; Jaffre, M.; Janoth, J.; Jansen, T.; Jönsson, L.; Johnson, D. P.; Johnson, L.; Jung, H.; Kalmus, P. I. P.; Kant, D.; Kaschowitz, R.; Kasselmann, P.; Kathage, U.; Katzy, J.; Kaufmann, H. H.; Kazarian, S.; Kenyon, I. R.; Kermiche, S.; Keuker, C.; Kiesling, C.; Klein, M.; Kleinwort, C.; Knies, G.; Ko, W.; Köhler, T.; Köhne, J. H.; Kolanoski, H.; Kole, F.; Kolya, S. D.; Korbel, V.; Korn, M.; Kostka, P.; Kotelnikov, S. K.; Krämerkämper, T.; Krasny, M. W.; Krehbiel, H.; Krücker, D.; Krüger, U.; Krüner-Marquis, U.; Küster, H.; Kuhlen, M.; Kurča, T.; Kurzhöfer, J.; Kuznik, B.; Lacour, D.; Lamarche, F.; Lander, R.; Landon, M. P. J.; Lange, W.; Lanius, P.; Laporte, J.-F.; Lebedev, A.; Lehner, F.; Leverenz, C.; Levonian, S.; Ley, Ch.; Lindner, A.; Lindström, G.; Link, J.; Linsel, F.; Lipinski, J.; List, B.; Lobo, G.; Loch, P.; Lohmander, H.; Lomas, J. W.; Lopez, G. C.; Lubimox, V.; Lüke, D.; Magnussen, N.; Malinovski, E.; Mani, S.; Maraček, R.; Marage, P.; Marks, J.; Marshall, R.; Martens, J.; Martin, G.; Martin, R.; Martyn, H.-U.; Martyniak, J.; Masson, S.; Mavroidis, T.; Maxfield, S. J.; McMahon, S. J.; Mehta, A.; Meier, K.; Mercer, D.; Merz, T.; Meyer, A.; Meyer, C. A.; Meyer, H.; Meyer, J.; Migliori, A.; Mikocki, S.; Milstead, D.; Moreau, F.; Morris, J. V.; Mroczko, E.; Müller, G.; Müller, K.; Murín, P.; Nagovizin, V.; Nahnhauer, R.; Naroska, B.; Naumann, Th.; Newman, P. R.; Newton, D.; Neyret, D.; Nguyen, H. K.; Nicholls, T. C.; Niebergall, F.; Niebuhr, C.; Niedzballa, Ch.; Nisius, R.; Nowak, G.; Noyes, G. W.; Nyberg-Werther, M.; Oakden, M.; Oberlack, H.; Obrock, U.; Olsson, J. E.; Ozerov, D.; Panaro, E.; Panitch, A.; Pascaud, C.; Patel, G. D.; Peppel, E.; Perez, E.; Phillips, J. P.; Pichler, Ch.; Pieuchot, A.; Pitzl, D.; Pope, G.; Prell, S.; Prosi, R.; Rabbertz, K.; Rädel, G.; Raupach, F.; Reimer, P.; Reinshagen, S.; Ribarics, P.; Rick, H.; Riech, V.; Riedlberger, J.; Riess, S.; Rietz, M.; Rizvi, E.; Robertson, S. M.; Robmann, P.; Roloff, H. E.; Roosen, R.; Rosenbauer, K.; Rostovtsev, A.; Rouse, F.; Yoyon, C.; Rüter, K.; Rusakov, S.; Rybicki, K.; Rylko, R.; Sahlmann, N.; Sankey, D. P. C.; Schacht, P.; Schiek, S.; Schleif, S.; Schleper, P.; von Schlippe, W.; Schmidt, D.; Schmidt, G.; Schöning, A.; Schröder, V.; Schuhmann, E.; Schwab, B.; Sciacca, G.; Sefkow, F.; Seidel, M.; Sell, R.; Semenov, A.; Shekelyan, V.; Sheviakov, I.; Shtarkov, L. N.; Siegmon, G.; Siewert, U.; Sirois, Y.; Skillicorn, I. O.; Smirnov, P.; Smith, J. R.; Solochenko, V.; Soloviev, Y.; Spiekermann, J.; Spielman, S.; Spitzer, H.; Starosta, R.; Steenbock, M.; Steffen, P.; Steinberg, R.; Stella, B.; Stephens, K.; Stier, J.; Stiewe, J.; Stößlein, U.; Stolze, K.; Strachota, J.; Straumann, U.; Struczinski, W.; Sutton, J. P.; Tapprogge, S.; Tchernyshov, V.; Thiebaux, C.; Thompson, G.; Truöl, P.; Turnau, J.; Tutas, J.; Uelkes, P.; Usik, A.; Valkár, S.; Valkárová, A.; Vallée, C.; Vandenplas, D.; Van Esch, P.; Van Mechelen, P.; Vartapetian, A.; Vazdik, Y.; Verrecchia, P.; Villet, G.; Wacker, K.; Wagener, A.; Wagener, M.; Walther, A.; Weber, G.; Weber, M.; Wegener, D.; Wegner, A.; Wellisch, H. P.; West, L. R.; Willard, S.; Winde, M.; Winter, G.-G.; Wittek, C.; Wright, A. E.; Wünsch, E.; Wulff, N.; Yiou, T. P.; Žáček, J.; Zarbock, D.; Zhang, Z.; Zhokin, A.; Zimmer, M.; Zimmermann, W.; Zomer, F.; Zuber, K.; zur Nedden, M.; H1 Collaboration

1995-02-01

A leading order determination of the gluon density in the proton has been performed in the fractional momentum range 1.9 · 10 -3 < xg/ p < 0.18 by measuring multi-jet events from boson-gluon fusion in deep-inelastic scattering with the H1 detector at the electron-proton collider HERA. This direct determination of the gluon density was performed in a kinematic region previously not accessible. The data show a considerable increase of the gluon density with decreasing fractional momenta of the gluons.

A new approach to determine the density of liquids and solids without measuring mass and volume: introducing the solidensimeter

NASA Astrophysics Data System (ADS)

Kiriktaş, Halit; Şahin, Mehmet; Eslek, Sinan; Kiriktaş, İrem

2018-05-01

This study aims to design a mechanism with which the density of any solid or liquid can be determined without measuring its mass and volume in order to help students comprehend the concept of density more easily. The solidensimeter comprises of two scaled and nested glass containers (graduated cylinder or beaker) and sufficient water. In this method, the density measurement was made using the Archimedes’ principle stating that an object fully submerged in a liquid displaces the same amount of liquid as its volume, while an object partially submerged or floating displaces the same amount of liquid as its mass. Using this method, the density of any solids or liquids can be determined using a simple mathematical ratio. At the end of the process a mechanism that helps students to comprehend the density topic more easily was designed. The system is easy-to-design, uses low-cost equipment and enables one to determine the density of any solid or liquid without measuring its mass and volume.

Layer 5 Pyramidal Neurons' Dendritic Remodeling and Increased Microglial Density in Primary Motor Cortex in a Murine Model of Facial Paralysis

PubMed Central

Urrego, Diana; Troncoso, Julieta; Múnera, Alejandro

2015-01-01

This work was aimed at characterizing structural changes in primary motor cortex layer 5 pyramidal neurons and their relationship with microglial density induced by facial nerve lesion using a murine facial paralysis model. Adult transgenic mice, expressing green fluorescent protein in microglia and yellow fluorescent protein in projecting neurons, were submitted to either unilateral section of the facial nerve or sham surgery. Injured animals were sacrificed either 1 or 3weeks after surgery. Two-photon excitation microscopy was then used for evaluating both layer 5 pyramidal neurons and microglia in vibrissal primary motor cortex (vM1). It was found that facial nerve lesion induced long-lasting changes in the dendritic morphology of vM1 layer 5 pyramidal neurons and in their surrounding microglia. Dendritic arborization of the pyramidal cells underwent overall shrinkage. Apical dendrites suffered transient shortening while basal dendrites displayed sustained shortening. Moreover, dendrites suffered transient spine pruning. Significantly higher microglial cell density was found surrounding vM1 layer 5 pyramidal neurons after facial nerve lesion with morphological bias towards the activated phenotype. These results suggest that facial nerve lesions elicit active dendrite remodeling due to pyramidal neuron and microglia interaction, which could be the pathophysiological underpinning of some neuropathic motor sequelae in humans. PMID:26064916

Methylation of zebularine investigated using density functional theory calculations.

PubMed

Selvam, Lalitha; Chen, Fang Fang; Wang, Feng

2011-07-30

Deoxyribonucleic acid (DNA) methylation is an epigenetic phenomenon, which adds methyl groups into DNA. This study reveals methylation of a nucleoside antibiotic drug 1-(β-D-ribofuranosyl)-2-pyrimidinone (zebularine or zeb) with respect to its methylated analog, 1-(β-D-ribofuranosyl)-5-methyl-2-pyrimidinone (d5) using density functional theory calculations in valence electronic space. Very similar infrared spectra suggest that zeb and d5 do not differ by types of the chemical bonds, but distinctly different Raman spectra of the nucleoside pair reveal that the impact caused by methylation of zeb can be significant. Further valence orbital-based information details on valence electronic structural changes caused by methylation of zebularine. Frontier orbitals in momentum space and position space of the molecules respond differently to methylation. Based on the additional methyl electron density concentration in d5, orbitals affected by the methyl moiety are classified into primary and secondary contributors. Primary methyl contributions include MO8 (57a), MO18 (47a), and MO37 (28a) of d5, which concentrates on methyl and the base moieties, suggest certain connection to their Frontier orbitals. The primary and secondary methyl affected orbitals provide useful information on chemical bonding mechanism of the methylation in zebularine. Copyright © 2011 Wiley Periodicals, Inc.

Direct Determination of Vibrational Density of States Change on Ligand Binding to a Protein

NASA Astrophysics Data System (ADS)

Balog, Erika; Becker, Torsten; Oettl, Martin; Lechner, Ruep; Daniel, Roy; Finney, John; Smith, Jeremy C.

2004-07-01

The change in the vibrational density of states of a protein (dihydrofolate reductase) on binding a ligand (methotrexate) is determined using inelastic neutron scattering. The vibrations of the complex soften significantly relative to the unbound protein. The resulting free-energy change, which is directly determined by the density of states change, is found to contribute significantly to the binding equilibrium.

Co-regulation of Primary Mouse Hepatocyte Viability and Function by Oxygen and Matrix

PubMed Central

Buck, Lorenna D.; Inman, S. Walker; Rusyn, Ivan; Griffith, Linda G.

2014-01-01

Although oxygen and extracellular matrix cues both influence differentiation state and metabolic function of primary rat and human hepatocytes, relatively little is known about how these factors together regulate behaviors of primary mouse hepatocytes in culture. To determine the effects of pericellular oxygen tension on hepatocellular function, we employed 2 methods of altering oxygen concentration in the local cellular microenvironment of cells cultured in the presence or absence of an extracellular matrix (Matrigel) supplement. By systematically altering medium depth and gas phase oxygen tension, we created multiple oxygen regimes (hypoxic, normoxic, and hyperoxic) and measured the local oxygen concentrations in the pericellular environment using custom-designed oxygen microprobes. From these measurements of oxygen concentrations, we derived values of oxygen consumption rates under a spectrum of environmental contexts, thus providing the first reported estimates of these values for primary mouse hepatocytes. Oxygen tension and matrix microenvironment were found to synergistically regulate hepatocellular survival and function as assessed using quantitative image analysis for cells stained with vital dyes, and assessment of secretion of albumin. Hepatocellular viability was affected only at strongly hypoxic conditions. Surprisingly, albumin secretion rates were greatest at a moderately supra-physiological oxygen concentration, and this effect was mitigated at still greater supra-physiological concentrations. Matrigel enhanced the effects of oxygen on retention of function. This study underscores the importance of carefully controlling cell density, medium depth and gas phase oxygen, as the effects of these parameters on local pericellular oxygen tension and subsequent hepatocellular function are profound. PMID:24222008

ECOLOGICAL DETERMINANTS OF AVIAN INFLUENZA VIRUS, WEST NILE VIRUS, AND AVIAN PARAMYXOVIRUS INFECTION AND ANTIBODY STATUS IN BLUE-WINGED TEAL (ANAS DISCORS) IN THE CANADIAN PRAIRIES.

PubMed

Nallar, Rodolfo; Papp, Zsuzsanna; Leighton, Frederick A; Epp, Tasha; Pasick, John; Berhane, Yohannes; Lindsay, Robbin; Soos, Catherine

2016-01-01

The Canadian prairies are one of the most important breeding and staging areas for migratory waterfowl in North America. Hundreds of thousands of waterfowl of numerous species from multiple flyways converge in and disperse from this region annually; therefore this region may be a key area for potential intra- and interspecific spread of infectious pathogens among migratory waterfowl in the Americas. Using Blue-winged Teal (Anas discors, BWTE), which have the most extensive migratory range among waterfowl species, we investigated ecologic risk factors for infection and antibody status to avian influenza virus (AIV), West Nile virus (WNV), and avian paramyxovirus-1 (APMV-1) in the three prairie provinces (Alberta, Saskatchewan, and Manitoba) prior to fall migration. We used generalized linear models to examine infection or evidence of exposure in relation to host (age, sex, body condition, exposure to other infections), spatiotemporal (year, province), population-level (local population densities of BWTE, total waterfowl densities), and environmental (local pond densities) factors. The probability of AIV infection in BWTE was associated with host factors (e.g., age and antibody status), population-level factors (e.g., local BWTE population density), and year. An interaction between age and AIV antibody status showed that hatch year birds with antibodies to AIV were more likely to be infected, suggesting an antibody response to an active infection. Infection with AIV was positively associated with local BWTE density, supporting the hypothesis of density-dependent transmission. The presence of antibodies to WNV and APMV-1 was positively associated with age and varied among years. Furthermore, the probability of being WNV antibody positive was positively associated with pond density rather than host population density, likely because ponds provide suitable breeding habitat for mosquitoes, the primary vectors for transmission. Our findings highlight the importance of spatiotemporal, environmental, and host factors at the individual and population levels, all of which may influence dynamics of these and other viruses in wild waterfowl populations.

Twenty-four years after theYellowstone Fires: Are postfire lodgepole pine stands converging in structure and function?

PubMed

Turner, Monica G; Whitby, Timothy G; Tinker, Daniel B; Romme, William H

2016-05-01

Disturbance and succession have long been of interest in ecology, but how landscape patterns of ecosystem structure and function evolve following large disturbances is poorly understood. After nearly 25 years, lodgepole pine (Pinus contorta var. latifolia) forests that regenerated after the 1988 Yellowstone Fires (Wyoming, USA) offer a prime opportunity to track the fate of disturbance-created heterogeneity in stand structure and function in a wilderness setting. In 2012, we resampled 72 permanent plots to ask (1) How have postfire stand structure and function changed between 11 and 24 yr postfire, and what variables explain these patterns and changes? (2) How has landscape-level (among-stand) variability in postfire stand structure and function changed between 11 and 24 yr postfire? We expected to see evidence of convergence beginning to emerge, but also that initial postfire stem density would still determine trajectories of biomass accumulation. After 24 yr, postfire lodgepole pine density remained very high (mean = 21,738 stems/ha, range = 0-344,067 stems/ha). Stem density increased in most plots between 11 and 24 yr postfire, but declined sharply where 11-yr-postfire stem density was > 72,000 stems/ha. Stems were small in high-density stands, but stand-level lodgepole pine leaf area, foliage biomass, and live aboveground biomass increased over time and with increasing stem density. After 24 yr, mean annual lodgepole pine aboveground net primary production (ANPP) was high (mean = 5 Mg · ha⁻¹ · yr⁻¹, range = 0-16.5 Mg · ha⁻¹ · yr⁻¹). Among stands, lodgepole pine ANPP increased with stem density, which explained 69% of the variation; another 8% of the variation was explained by environmental covariates. Early patterns of postfire lodgepole pine regeneration, which were contingent on prefire serotiny and fire severity, remained the dominant driver of stand structure and function. We observed mechanisms that would lead to convergence in stem density (structure) over time, but it was landscape variation in functional variables that declined substantially. Stand structure and function have not converged across the burned landscape, but our evidence suggests function will converge sooner than structure.

Forced and natural convection in aggregate-laden nanofluids

NASA Astrophysics Data System (ADS)

Thajudeen, Thaseem; Hogan, Christopher J.

2011-12-01

A number of experimental and theoretical studies of convective heat transfer in nanofluids (liquid suspensions of nanoparticles, typically with features below 100 nm in size) reveal contrasting results; nanoparticles can either enhance or reduce the convective heat transfer coefficient. These disparate conclusions regarding the influence of nanoparticles on convective heat transfer may arise due to the aggregation of nanoparticles, which is often not considered in studies of nanofluids. Here, we examine theoretically forced and natural convective heat transfer of aggregate-laden nanofluids using Monte Carlo-based models to determine how the aggregate morphology influences the convective heat transfer coefficient. Specifically, in this study, it is first shown that standard heat transfer correlations should apply to nanofluids, and the main influence of the nanoparticles is to alter suspension thermal conductivity, dynamic viscosity, density, specific heat, and thermal expansion coefficient. Aggregated particles in suspension are modeled as quasi-fractal aggregates composed of individual primary particles described by the primary particle radius, number of primary particles, fractal (Hausdorff) dimension, pre-exponential factor, and degree of coalescence between primary particles. A sequential algorithm is used to computationally generate aggregates with prescribed morphological descriptors. Four types of aggregates are considered; spanning the range of aggregate morphologies observed in nanofluids. For each morphological type, the influences of aggregates on nanofluid dynamic viscosity and thermal conductivity are determined via first passage-based Brownian dynamics calculations. It is found that depending on both the material properties of the nanoparticles as well as the nanoparticle morphology, the addition of nanoparticles to a suspension can either increase or decrease both the forced and natural convective heat transfer coefficients, with both a 51% increase and a 32% decrease in the heat transfer coefficient achievable at particle volume fractions of 0.05. This study shows clearly that the influence of particle morphology needs to be accounted for in all studies of heat transfer in nanofluids.

Evaluation of the quality of care of a multi-disciplinary Risk Factor Assessment and Management Programme for Hypertension (RAMP-HT).

PubMed

Yu, Esther Yee Tak; Wan, Eric Yuk Fai; Chan, Karina Hiu Yen; Wong, Carlos King Ho; Kwok, Ruby Lai Ping; Fong, Daniel Yee Tak; Lam, Cindy Lo Kuen

2015-06-19

There is some evidence to support a risk-stratified, multi-disciplinary approach to manage patients with hypertension in primary care. The aim of this study is to evaluate the quality of care (QOC) of a multi-disciplinary Risk Assessment and Management Programme for Hypertension (RAMP-HT) for hypertensive patients in busy government-funded primary care clinics in Hong Kong. The objectives are to develop an evidence-based, structured and comprehensive evaluation framework on quality of care, to enhance the QOC of the RAMP-HT through an audit spiral of two evaluation cycles and to determine the effectiveness of the programme in reducing cardiovascular disease (CVD) risk. A longitudinal study is conducted using the Action Learning and Audit Spiral methodologies to measure whether pre-set target standards of care intended by the RAMP-HT are achieved. A structured evaluation framework on the quality of structure, process and outcomes of care has been developed based on the programme objectives and literature review in collaboration with the programme workgroup and health service providers. Each participating clinic is invited to complete a structure of care evaluation questionnaire in each evaluation cycle. The data of all patients who have enrolled into the RAMP-HT in the pre-defined evaluation periods are used for the evaluation of the process and outcomes of care in each evaluation cycle. For evaluation of the effectiveness of RAMP-HT, the primary outcomes including blood pressure (both systolic and diastolic), low-density lipoprotein cholesterol and estimated 10-year CVD risk of RAMP-HT participants are compared to those of hypertensive patients in usual care without RAMP-HT. The QOC and effectiveness of the RAMP-HT in improving clinical and patient-reported outcomes for patients with hypertension in normal primary care will be determined. Possible areas for quality enhancement and standards of good practice will be established to inform service planning and policy decision making.

Population management, systems-based practice, and planned chronic illness care: integrating disease management competencies into primary care to improve composite diabetes quality measures.

PubMed

Kimura, Joe; DaSilva, Karen; Marshall, Richard

2008-02-01

The increasing prevalence of chronic illnesses in the United States requires a fundamental redesign of the primary care delivery system's structure and processes in order to meet the changing needs and expectations of patients. Population management, systems-based practice, and planned chronic illness care are 3 potential processes that can be integrated into primary care and are compatible with the Chronic Care Model. In 2003, Harvard Vanguard Medical Associates, a multispecialty ambulatory physician group practice based in Boston, Massachusetts, began implementing all 3 processes across its primary care practices. From 2004 to 2006, the overall diabetes composite quality measures improved from 51% to 58% for screening (HgA1c x 2, low-density lipoprotein, blood pressure in 12 months) and from 13% to 17% for intermediate outcomes (HgA1c

Development and integration of pharmacist clinical services into the patient-centered medical home.

PubMed

Berdine, Hildegarde J; Skomo, Monica L

2012-01-01

To describe the development of pharmacist clinical services within a primary care physician practice using a standardized business plan, the extent of clinical pharmacy service integration into the patient-centered medical home (PCMH), and the clinical changes in the pharmacist's patient cohort. A two-physician primary care/occupational care practice in Pittsburgh, PA, from May 2007 to December 2011. Pharmacist-led clinic receives physician referrals for medication management, adherence, and disease management services. Pharmacist practice in a primary care setting with emphasis on integration of clinical services into the medical home model designed by the American Academy of Family Physicians. Characterization of the patient's pharmacist and services provided by the pharmacist. Glycosylated hemoglobin (A1C), body mass index (BMI), low-density lipoprotein cholesterol, high-density lipoprotein cholesterol, total cholesterol, triglycerides, and blood pressure. The top five primary referral reasons were diabetes self-management, weight management, medication adherence, hypertension, and dyslipidemia management. Improvements in clinical parameters were demonstrated for lipids and A1C at 1 and 2 years after baseline. Statistically significant improvements in BMI also were observed. The pharmacist developed and integrated clinical services into a primary care practice, became an integral member of the clinical team in the two-physician PCMH, and improved patient outcomes.

In-situ Electrodeposition of Highly Active Silver Catalyst on Carbon Fiber Papers as Binder Free Cathodes for Aluminum-air Battery.

PubMed

Hong, Qingshui; Lu, Huimin

2017-06-13

Carbon fiber papers supported Ag catalysts (Ag/CFP) with different coverage of electro-active site are prepared by electrochemical deposition and used as binder free cathodes in primary aluminum-air (Al-air) battery. Scanning Electron Microscopy and X-ray Diffraction studies are carried out to characterize the as-prepared Ag/CFP air cathodes. Oxygen reduction reaction (ORR) activities on these air cathodes in alkaline solutions are systematic studied. A newly designed aluminum-air cell is used to further determine the cathodes performance under real operation condition and during the test, the Ag/CFP electrodes show outstanding catalytic activity for ORR in concentrated alkaline electrolyte, and no obvious activity degradation is observed after long-time discharge. The electrochemical test results display the dependence of coverage of the electro-active Ag on the catalytic performance of the air cathodes. The resulting primary Al-air battery made from the best-performing cathode shows an impressive discharge peak power density, outperforming that of using commercial nano-manganese catalyst air electrodes.

Complex numerical responses to top-down and bottom-up processes in vertebrate populations.

PubMed Central

Sinclair, A R E; Krebs, Charles J

2002-01-01

Population growth rate is determined in all vertebrate populations by food supplies, and we postulate bottom-up control as the universal primary standard. But this primary control system can be overridden by three secondary controls: top-down processes from predators, social interactions within the species and disturbances. Different combinations of these processes affect population growth rates in different ways. Thus, some relationships between growth rate and density can be hyperbolic or even have multiple nodes. We illustrate some of these in marsupial, ungulate and rabbit populations. Complex interactions between food, predators, environmental disturbance and social behaviour produce the myriad observations of population growth in nature, and we need to develop generalizations to classify populations. Different animal groups differ in the combination of these four processes that affect them, in their growth rates and in their vulnerability to extinction. Because conservation and management of populations depend critically on what factors drive population growth, we need to develop universal generalizations that will relieve us from the need to study every single population before we can make recommendations for management. PMID:12396514

Evaluation of high-energy lithium thionyl chloride primary cells

NASA Technical Reports Server (NTRS)

Frank, H. A.

1980-01-01

An advanced commercial primary lithium cell (LiSoCl2) was evaluated in order to establish baseline data for improved lithium batteries for aerospace applications. The cell tested had nominal capacity of 6 Ah. Maximum energy density at low rates (less than C/30, where C is the cell capacity in amp-hrs and 30 corresponds to a 30 hr discharge time) was found to be near 300 Wh/kg. An equation which predicts the operating voltage of these cells as a function of current and state of charge is presented. Heat generation rates of these cells were determined as a function of current in a calorimeter. It was found that heat rates could be theoretically predicted with some degree of accuracy at currents less than 1 amp or the C/6 rate. No explosions were observed in the cells during the condition of overdischarge or reversal nor during high rate discharge. It was found, however, that the cells can vent when overdischarge currents are greater than C/30 and when discharge rates are greater than 1.5C.

Water-quality parameters and benthic algal communities at selected streams in Minnesota, August 2000 - Study design, methods and data

USGS Publications Warehouse

Lee, K.E.

2002-01-01

This report describes the study design, sampling methods, and summarizes the physical, chemical, and benthic algal data for a component of the multiagency study that was designed to document diurnal water-quality measurements (specific conductance, pH, water temperature, and dissolved oxygen), benthic algal community composition and chlorophyll-a content, and primary productivity at 12 stream sites on 6 streams in Minnesota during August 2000. Specific conductance, pH, water temperature, dissolved oxygen concentrations and percent dissolved oxygen saturation measurements were made with submersible data recorders at 30 minute intervals for a period of 3-6 days during August 2000. Benthic algae collected from wood and rock substrate were identified and enumerated. Biovolume (volume of algal cells per unit area), density (number of cells per unit area), and chlorophyll-a content from benthic algae were determined. These data can be used as part of the multiagency study to develop an understanding of the relations among nutrient concentrations, algal abundance, algal community composition, and primary production and respiration processes in rivers of differing ecoregions in Minnesota.

Meteoroid Bulk Density and Ceplecha Types

NASA Technical Reports Server (NTRS)

Blaauw, R. C.; Moser, D. E.; Moorhead, A. V.

2017-01-01

The determination of asteroid bulk density is an important aspect of Near Earth Object (NEO) characterization. A fraction of meteoroids originate from asteroids (including some NEOs), thus in lieu of mutual perturbations, satellites, or expensive spacecraft missions, a study of meteoroid bulk densities can potentially provide useful insights into the densities of NEOs and PHOs (Potentially Hazardous Objects). Meteoroid bulk density is still inherently difficult to measure, and is most often determined by modeling the ablation of the meteoroid. One approach towards determining a meteoroid density distribution entails using a more easily measured proxy for the densities, then calibrating the proxy with known densities from meteorite falls, ablation modelling, and other sources. An obvious proxy choice is the Ceplecha type, KB (Ceplecha, 1958), which is thought to indicate the strength of a meteoroid and often correlated to different bulk densities in literature. KB is calculated using the air density at the beginning height of the meteor, the initial velocity, and the zenith angle of the radiant; quantities more readily determined than meteoroid bulk density itself. Numerical values of K(sub B) are sorted into groups (A, B, C, etc.), which have been matched to meteorite falls or meteor showers with known composition such as the porous Draconids. An extensive survey was conducted to establish the strength of the relationship between bulk density and K(sub B), specifically looking at those that additionally determined K(sub B) for the meteors. In examining the modeling of high-resolution meteor data from Kikwaya et al. (2011), the correlation between K(sub B) and bulk density was not as strong as hoped. However, a distinct split by dynamical type was seen with Jovian Tisserand parameter (T(sub J)), with meteoroids from Halley Type comets (T(sub J) < 2) exhibiting much lower bulk densities than those originating from Jupiter Family comets and asteroids (T(sub J) > 2). Therefore, this work indicates that the dynamical classification of a meteoroid is a better indicator of the density than the strength proxy, a somewhat surprising result.

Electron density studies of methyl cellobioside

USDA-ARS?s Scientific Manuscript database

Experimental X-ray diffraction crystallography determines the variations in electron density that result from the periodic array of atoms in a crystal. Normally, the positions and type of atom are determined from the electron density based on an approximation that the atoms are spherical. However, t...

Discovery of a Satellite to Asteroid Family Member (702) Alauda

NASA Astrophysics Data System (ADS)

Margot, Jean-Luc; Rojo, P.

2007-10-01

Rojo and Margot [1] reported the discovery of a satellite to (702) Alauda from adaptive-optics imaging with the European Southern Observatory (ESO) 8-m Very Large Telescope (VLT) on Cerro Paranal, Chile. (702) Alauda (a = 3.2 AU, e = 0.02, i = 21 deg) has been identified as the largest member of a dynamical family [2,3], suggesting a possible origin of the satellite in the family formation event. The diameter of (702) Alauda is given in the IRAS Minor Planet Survey (IMPS) as 194.73 +/- 3.2 km [4]. If the primary and secondary have similar albedoes, the diameter of the satellite is about 5.5 km. This is based on the measured flux ratio between primary and secondary of 1250, possibly the largest ever observed for solar system binaries with adaptive optics. This is the first satellite discovered to a large minor planet of type B in the SMASSII taxonomy, which is defined by a linear featureless spectrum with bluish to neutral slope [5]. B-types are carbonaceous asteroids that are not well characterized. The mass and density estimates of B-type (2) Pallas vary by 50% [6,7]. Our ongoing determination of the satellite orbit will provide mass and density estimates for (702) Alauda. [1] Rojo and Margot, CBET 1016, 2007. [2] Foglia and Masi 2004, Minor Planet Bull. 41, 100. [3] Gil-Hutton 2006, Icarus 183, 93. [4] Tedesco 2002, AJ 123, 1056. [5] Bus and Binzel 2002, Icarus 158, 146. [6] Hilton 2002, Asteroids III, 103. [7] Britt et al. 2002, Asteroids III, 485.

Increase of bioavailable testosterone is associated with gain in bone mineral density after cure of primary hyperparathyroidism in postmenopausal women.

PubMed

Almqvist, Erik G; Becker, Charlotte; Bondeson, Anne-Greth; Bondeson, Lennart; Svensson, Johan

2006-01-01

The recovery of bone mineral density (BMD) after surgical cure of primary hyperparathyroidism (PHPT) seems to be multifactorial and not just dependent on declining PTH. The aim of the present study was to evaluate the role of sex steroids in this context. Thirty-six postmenopausal women with PHPT were examined before and 1 year after curative parathyroidectomy. Their mean age at inclusion in the study was 71.7 +/- 1.1 years (range 54-83). BMD was measured in hip and lumbar spine using dual energy X-ray absorptiometry. No patient received any replacement therapy with sex hormones or treatment with corticosteroids, oestrogen receptor modulators or bisphosphonates. Serum concentrations of oestradiol, testosterone, androstenedione, dehydroepiandrosterone sulphate, SHBG, PTH and calcium. Postoperative increase of free (bioavailable) testosterone was positively correlated to the change of BMD in the hip (P < 0.01), whereas the change of PTH in serum correlated to the change of BMD in the lumbar spine (P < 0.05). Multiple regression analysis showed that bioavailable testosterone was the most important determinant of change in BMD in both spine and hip (femoral neck: P < 0.05; Ward's triangle: P < 0.001; trochanter: P < 0.01; lumbar spine: P < 0.05). The increase of bioavailable testosterone after curative parathyroidectomy was related to declining SHBG. An increase of bioavailable testosterone following surgical cure of PHPT is related to improvement of hip and lumbar spine BMD in postmenopausal women. This previously unknown hormonal interaction may also be important to other aspects of hyperparathyroidism.

A self-similar magnetohydrodynamic model for ball lightnings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsui, K. H.

2006-07-15

Ball lightning is modeled by magnetohydrodynamic (MHD) equations in two-dimensional spherical geometry with azimuthal symmetry. Dynamic evolutions in the radial direction are described by the self-similar evolution function y(t). The plasma pressure, mass density, and magnetic fields are solved in terms of the radial label {eta}. This model gives spherical MHD plasmoids with axisymmetric force-free magnetic field, and spherically symmetric plasma pressure and mass density, which self-consistently determine the polytropic index {gamma}. The spatially oscillating nature of the radial and meridional field structures indicate embedded regions of closed field lines. These regions are named secondary plasmoids, whereas the overall self-similarmore » spherical structure is named the primary plasmoid. According to this model, the time evolution function allows the primary plasmoid expand outward in two modes. The corresponding ejection of the embedded secondary plasmoids results in ball lightning offering an answer as how they come into being. The first is an accelerated expanding mode. This mode appears to fit plasmoids ejected from thundercloud tops with acceleration to ionosphere seen in high altitude atmospheric observations of sprites and blue jets. It also appears to account for midair high-speed ball lightning overtaking airplanes, and ground level high-speed energetic ball lightning. The second is a decelerated expanding mode, and it appears to be compatible to slowly moving ball lightning seen near ground level. The inverse of this second mode corresponds to an accelerated inward collapse, which could bring ball lightning to an end sometimes with a cracking sound.« less

Theoretical proposal for a magnetic resonance study of charge transport in organic semiconductors

NASA Astrophysics Data System (ADS)

Mkhitaryan, Vagharsh

Charge transport in disordered organic semiconductors occurs via carrier incoherent hops in a band of localized states. In the framework of continuous-time random walk the carrier on-site waiting time distribution (WTD) is one of the basic characteristics of diffusion. Besides, WTD is fundamentally related to the density of states (DOS) of localized states, which is a key feature of a material determining the optoelectric properties. However, reliable first-principle calculations of DOS in organic materials are not yet available and experimental characterization of DOS and WTD is desirable. We theoretically study the spin dynamics of hopping carriers and propose measurement schemes directly probing WTD, based on the zero-field spin relaxation and the primary (Hahn) spin echo. The proposed schemes are possible because, as we demonstrate, the long-time behavior of the zero-field relaxation and the primary echo is determined by WTD, both for the hyperfine coupling dominated and the spin-orbit coupling dominated spin dynamics. We also examine the dispersive charge transport, which is a non-Markovian sub-diffusive process characterized by non-stationarity. We show that the proposed schemes unambiguously capture the effects of non-stationarity, e.g., the aging behavior of random walks. This work was supported by the Department of Energy-Basic Energy Sciences under Contract No. DE-AC02-07CH11358.

Diagnostic Value of Multidetector CT and Its Multiplanar Reformation, Volume Rendering and Virtual Bronchoscopy Postprocessing Techniques for Primary Trachea and Main Bronchus Tumors

PubMed Central

Luo, Mingyue; Duan, Chaijie; Qiu, Jianping; Li, Wenru; Zhu, Dongyun; Cai, Wenli

2015-01-01

Purpose To evaluate the diagnostic value of multidetector CT (MDCT) and its multiplanar reformation (MPR), volume rendering (VR) and virtual bronchoscopy (VB) postprocessing techniques for primary trachea and main bronchus tumors. Methods Detection results of 31 primary trachea and main bronchus tumors with MDCT and its MPR, VR and VB postprocessing techniques, were analyzed retrospectively with regard to tumor locations, tumor morphologies, extramural invasions of tumors, longitudinal involvements of tumors, morphologies and extents of luminal stenoses, distances between main bronchus tumors and trachea carinae, and internal features of tumors. The detection results were compared with that of surgery and pathology. Results Detection results with MDCT and its MPR, VR and VB were consistent with that of surgery and pathology, included tumor locations (tracheae, n = 19; right main bronchi, n = 6; left main bronchi, n = 6), tumor morphologies (endoluminal nodes with narrow bases, n = 2; endoluminal nodes with wide bases, n = 13; both intraluminal and extraluminal masses, n = 16), extramural invasions of tumors (brokethrough only serous membrane, n = 1; 4.0 mm—56.0 mm, n = 14; no clear border with right atelectasis, n = 1), longitudinal involvements of tumors (3.0 mm, n = 1; 5.0 mm—68.0 mm, n = 29; whole right main bronchus wall and trachea carina, n = 1), morphologies of luminal stenoses (irregular, n = 26; circular, n = 3; eccentric, n = 1; conical, n = 1) and extents (mild, n = 5; moderate, n = 7; severe, n = 19), distances between main bronchus tumors and trachea carinae (16.0 mm, n = 1; invaded trachea carina, n = 1; >20.0 mm, n = 10), and internal features of tumors (fairly homogeneous densities with rather obvious enhancements, n = 26; homogeneous density with obvious enhancement, n = 1; homogeneous density without obvious enhancement, n = 1; not enough homogeneous density with obvious enhancement, n = 1; punctate calcification with obvious enhancement, n = 1; low density without obvious enhancement, n = 1). Conclusion MDCT and its MPR, VR and VB images have respective advantages and disadvantages. Their combination could complement to each other to accurately detect locations, natures (benignancy, malignancy or low malignancy), and quantities (extramural invasions, longitudinal involvements, extents of luminal stenoses, distances between main bronchus tumors and trachea carinae) of primary trachea and main bronchus tumors with crucial information for surgical treatment, are highly useful diagnostic methods for primary trachea and main bronchus tumors. PMID:26332466

Cell size and wall dimensions drive distinct variability of earlywood and latewood density in Northern Hemisphere conifers.

PubMed

Björklund, Jesper; Seftigen, Kristina; Schweingruber, Fritz; Fonti, Patrick; von Arx, Georg; Bryukhanova, Marina V; Cuny, Henri E; Carrer, Marco; Castagneri, Daniele; Frank, David C

2017-11-01

Interannual variability of wood density - an important plant functional trait and environmental proxy - in conifers is poorly understood. We therefore explored the anatomical basis of density. We hypothesized that earlywood density is determined by tracheid size and latewood density by wall dimensions, reflecting their different functional tasks. To determine general patterns of variability, density parameters from 27 species and 349 sites across the Northern Hemisphere were correlated to tree-ring width parameters and local climate. We performed the same analyses with density and width derived from anatomical data comprising two species and eight sites. The contributions of tracheid size and wall dimensions to density were disentangled with sensitivity analyses. Notably, correlations between density and width shifted from negative to positive moving from earlywood to latewood. Temperature responses of density varied intraseasonally in strength and sign. The sensitivity analyses revealed tracheid size as the main determinant of earlywood density, while wall dimensions become more influential for latewood density. Our novel approach of integrating detailed anatomical data with large-scale tree-ring data allowed us to contribute to an improved understanding of interannual variations of conifer growth and to illustrate how conifers balance investments in the competing xylem functions of hydraulics and mechanical support. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Polymer on Top: Current Limits and Future Perspectives of Quantitatively Evaluating Surface Grafting.

PubMed

Michalek, Lukas; Barner, Leonie; Barner-Kowollik, Christopher

2018-03-07

Well-defined polymer strands covalently tethered onto solid substrates determine the properties of the resulting functional interface. Herein, the current approaches to determine quantitative grafting densities are assessed. Based on a brief introduction into the key theories describing polymer brush regimes, a user's guide is provided to estimating maximum chain coverage and-importantly-examine the most frequently employed approaches for determining grafting densities, i.e., dry thickness measurements, gravimetric assessment, and swelling experiments. An estimation of the reliability of these determination methods is provided via carefully evaluating their assumptions and assessing the stability of the underpinning equations. A practical access guide for comparatively and quantitatively evaluating the reliability of a given approach is thus provided, enabling the field to critically judge experimentally determined grafting densities and to avoid the reporting of grafting densities that fall outside the physically realistic parameter space. The assessment is concluded with a perspective on the development of advanced approaches for determination of grafting density, in particular, on single-chain methodologies. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Carbon budget of Nyungwe Tropical Montane Rain Forest in Central Africa

NASA Astrophysics Data System (ADS)

Nyirambangutse, B.; Zibera, E.; Uwizeye, F. K.; Hansson, L.; Nsabimana, D.; Pleijel, H.; Uddling, J.; Wallin, G.

2015-12-01

African tropical rainforests host rich biodiversity and play many roles at different scales such as local, regional and global, in the functioning of the earth system. Despite that the African tropical forests are the world's second largest, it has been neglected in terms of understanding the storage and fluxes of carbon and other nutrients. The question of whether this biome is a net sink or source of atmospheric CO2 is still not answered, and little is known concerning the climate change response. Tropical montane forests are even more poorly sampled compared with their importance. Deeper understanding of these ecosystems is required to provide insights on how they might react under global change. To answer questions related to these issues for African tropical montane forests, 15 permanent 0.5 ha plots were established in 2011 in Nyungwe tropical montane rainforest gazetted as a National Park to protect its extensive floral and faunal diversity. The plots are arranged along an east-westerly transect and includes both primary and secondary forest communities. The study is connected to the global ecosystem monitoring network (GEM, http://gem.tropicalforests.ox.ac.uk/). The aim is to characterize spatial and temporal heterogeneity of carbon and nutrient dynamics processes. The role of microclimate, topography, human disturbances, and plant species to the variability of these pools and processes will be explored. We compare stocks and fluxes of carbon and nutrients of the secondary and primary forest communities. The carbon stock are determined by an inventory of height and diameter at breast height (dbh) of all trees with a dbh above 5 cm, wood density, biomass of understory vegetation, leaf area index, standing and fallen dead wood, fine root biomass and organic content of various soil layers (litter, organic and mineral soil down to 45 cm depth). The carbon fluxes are determined by measurements of photosynthesis and respiration of leaves, above and below ground tree growth (stem, and fine roots), litter fall and soil respiration. Results of the carbon budget defined through the net primary productivity (NPP), autotrophic respiration (Ra) and gross primary productivity (GPP) will be presented, comparing primary and secondary forest communities.

Non-Aqueous Primary Li-Air Flow Battery and Optimization of its Cathode through Experiment and Modeling.

PubMed

Kim, Byoungsu; Takechi, Kensuke; Ma, Sichao; Verma, Sumit; Fu, Shiqi; Desai, Amit; Pawate, Ashtamurthy S; Mizuno, Fuminori; Kenis, Paul J A

2017-09-22

A primary Li-air battery has been developed with a flowing Li-ion free ionic liquid as the recyclable electrolyte, boosting power capability by promoting superoxide diffusion and enhancing discharge capacity through separately stored discharge products. Experimental and computational tools are used to analyze the cathode properties, leading to a set of parameters that improve the discharge current density of the non-aqueous Li-air flow battery. The structure and configuration of the cathode gas diffusion layers (GDLs) are systematically modified by using different levels of hot pressing and the presence or absence of a microporous layer (MPL). These experiments reveal that the use of thinner but denser MPLs is key for performance optimization; indeed, this leads to an improvement in discharge current density. Also, computational results indicate that the extent of electrolyte immersion and porosity of the cathode can be optimized to achieve higher current density. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Validation of ionospheric electron density profiles inferred from GPS occultation observations of the GPS/MET experiment

NASA Astrophysics Data System (ADS)

Kawakami, Todd Mori

In April of 1995, the launch of the GPS Meteorology Experiment (GPS/MET) onboard the Orbview-1 satellite, formerly known as Microlab-1, provided the first technology demonstration of active limb sounding of the Earth's atmosphere with a low Earth orbiting spacecraft utilizing the signals transmitted by the satellites of the Global Positioning System (GPS). Though the experiment's primary mission was to probe the troposphere and stratosphere, GPS/MET was also capable of making radio occultation observations of the ionosphere. The application of the GPS occultation technique to the upper atmosphere created a unique opportunity to conduct ionospheric research with an unprecedented global distribution of observations. For operational support requirements, the Abel transform could be employed to invert the horizontal TEC profiles computed from the L1 and L2 phase measurements observed by GPS/MET into electron density profiles versus altitude in near real time. The usefulness of the method depends on how effectively the TEC limb profiles can be transformed into vertical electron density profiles. An assessment of GPS/MET's ability to determine electron density profiles needs to be examined to validate the significance of the GPS occultation method as a new and complementary ionospheric research tool to enhance the observational databases and improve space weather modeling and forecasting. To that end, simulations of the occultation observations and their inversions have been conducted to test the Abel transform algorithm and to provide qualitative information about the type and range of errors that might be experienced during the processing of real data. Comparisons of the electron density profiles inferred from real GPS/MET observations are then compared with coincident in situ measurements from the satellites of Defense Meteorological Satellite Program (DMSP) and ground-based remote sensing from digisonde and incoherent scatter radar facilities. The principal focus of this study is the validation of the electron density profiles inferred from GPS occultation observations using the Abel transform.

Postfragmentation density function for bacterial aggregates in laminar flow

PubMed Central

Byrne, Erin; Dzul, Steve; Solomon, Michael; Younger, John

2014-01-01

The postfragmentation probability density of daughter flocs is one of the least well-understood aspects of modeling flocculation. We use three-dimensional positional data of Klebsiella pneumoniae bacterial flocs in suspension and the knowledge of hydrodynamic properties of a laminar flow field to construct a probability density function of floc volumes after a fragmentation event. We provide computational results which predict that the primary fragmentation mechanism for large flocs is erosion. The postfragmentation probability density function has a strong dependence on the size of the original floc and indicates that most fragmentation events result in clumps of one to three bacteria eroding from the original floc. We also provide numerical evidence that exhaustive fragmentation yields a limiting density inconsistent with the log-normal density predicted in the literature, most likely due to the heterogeneous nature of K. pneumoniae flocs. To support our conclusions, artificial flocs were generated and display similar postfragmentation density and exhaustive fragmentation. PMID:21599205

Application of MODIS GPP to Forecast Risk of Hantavirus Pulmonary Syndrome Based on Fluctuations in Reservoir Population Density

NASA Astrophysics Data System (ADS)

Loehman, R.; Heinsch, F. A.; Mills, J. N.; Wagoner, K.; Running, S.

2003-12-01

Recent predictive models for hantavirus pulmonary syndrome (HPS) have used remotely sensed spectral reflectance data to characterize risk areas with limited success. We present an alternative method using gross primary production (GPP) from the MODIS sensor to estimate the effects of biomass accumulation on population density of Peromyscus maniculatus (deer mouse), the principal reservoir species for Sin Nombre virus (SNV). The majority of diagnosed HPS cases in North America are attributed to SNV, which is transmitted to humans through inhalation of excretions and secretions from infected rodents. A logistic model framework is used to evaluate MODIS GPP, temperature, and precipitation as predictors of P. maniculatus density at established trapping sites across the western United States. Rodent populations are estimated using monthly minimum number alive (MNA) data for 2000 through 2002. Both local meteorological data from nearby weather stations and 1.25 degree x 1 degree gridded data from the NASA DAO were used in the regression model to determine the spatial sensitivity of the response. MODIS eight-day GPP data (1-km resolution) were acquired and binned to monthly average and monthly sum GPP for 3km x 3km grids surrounding each rodent trapping site. The use of MODIS GPP to forecast HPS risk may result in a marked improvement over past reflectance-based risk area characterizations. The MODIS GPP product provides a vegetation dynamics estimate that is unique to disease models, and targets the fundamental ecological processes responsible for increased rodent density and amplified disease risk.

Adsorption and transport of charged vs. neutral hydrophobic molecules at the membrane of murine erythroleukemia (MEL) cells.

PubMed

Zeng, Jia; Eckenrode, Heather M; Dai, Hai-Lung; Wilhelm, Michael J

2015-03-01

The adsorption and transport of hydrophobic molecules at the membrane surface of pre- and post-DMSO induced differentiated murine erythroleukemia (MEL) cells were examined by time- and wavelength-resolved second harmonic light scattering. Two medium (<600 Da) hydrophobic molecules, cationic malachite green (MG) and neutral bromocresol purple (BCP), were investigated. While it was observed that the MG cation adsorbs onto the surface of the MEL cell, neutral BCP does not. It is suggested that an electrostatic interaction between the opposite charges of the cation and the MEL cell surface is the primary driving force for adsorption. Comparisons of adsorption density and free energy, measured at different pH and cell morphology, indicate that the interaction is predominantly through sialic acid carboxyl groups. MG cation adsorption densities have been determined as (0.6±0.3)×10(6) μm(-2) on the surface of undifferentiated MEL cells, and (1.8±0.5)×10(7) μm(-2) on differentiated MEL cells, while the deduced adsorption free energies are effectively identical (ca. -10.9±0.1 and -10.8±0.1 kcal mol(-1), respectively). The measured MG densities indicate that the total number of surface carboxyl groups is largely conserved following differentiation, and therefore the density of carboxylic groups is much larger on the differentiated cell surface than the undifferentiated one. Finally, in contrast to synthetic liposomes and bacterial membranes, surface adsorbed MG cations are unable to traverse the MEL cell membrane. Copyright © 2015 Elsevier B.V. All rights reserved.

Superficial ovarian cortex vascularization is inversely related to the follicle reserve in normal cycling ovaries and is increased in polycystic ovary syndrome.

PubMed

Delgado-Rosas, F; Gaytán, M; Morales, C; Gómez, R; Gaytán, F

2009-05-01

The superficial ovarian cortex constitutes the micro-environment where resting and early growing follicles reside. As small follicles do not possess an independent capillary network, both their survival and early growth depend on their proximity to the cortical vessels. Little is known about the possible changes in superficial ovarian cortex vascularization in normal women throughout reproductive life or in pathological conditions such as polycystic ovary syndrome (PCOS) involving abnormal early follicle growth. We studied the vascularization of the superficial and deep cortical stroma (DCS) in normal cycling ovaries from 21 to 50 years of age and in infertile women with PCOS. We used archival ovarian samples and specific CD34 immunostaining to determine blood vessel density and to analyse correlation with age and with the ovarian follicle reserve. Normal cycling ovaries showed an age-related increase in the superficial cortical stroma vascularization that was inversely correlated with the density of small (primordial and primary) follicles. In contrast, blood vessel density in the DCS significantly decreased in women aged >or=40 years. Ovaries from PCOS showed a 2-fold increase in blood vessel density in both superficial cortical stroma and DCS with respect to age-matched controls. The increased vascularization of the superficial cortical stroma in normal ovaries in relation to age and in ovaries from PCOS could have profound effects on cortical metabolic rate, primordial follicle survival/activation and early follicle growth, and may underline changes in follicle dynamics in mid-aged women and in PCOS.

Effectiveness and feasibility of lowering playground density during recess to promote physical activity and decrease sedentary time at primary school

PubMed Central

2013-01-01

Background This pilot study aimed at investigating the effectiveness of lowering playground density on increasing children’s physical activity and decreasing sedentary time. Also the feasibility of this intervention was tested. Methods Data were collected in September and October 2012 in three Belgian schools in 187, 9–12 year old children. During the intervention, playground density was decreased by splitting up recesses and decreasing the number of children sharing the playground. A within-subject design was used. Children wore accelerometers during the study week. Three-level (class – participant - measurement (baseline or intervention)) linear regression models were used to determine intervention effects. After the intervention week the school principals filled out a questionnaire concerning the feasibility of the intervention. Results The available play space was 12.18 ± 4.19 m2/child at baseline and increased to 24.24 ± 8.51 m2/child during intervention. During the intervention sedentary time decreased (−0.58 min/recess; -3.21%/recess) and moderate-to-vigorous physical activity (+1.04 min/recess; +5.9%/recess) increased during recess and during the entire school day (sedentary time: -3.29%/school day; moderate-to-vigorous physical activity +1.16%/school day). All principals agreed that children enjoyed the intervention; but some difficulties were reported. Conclusions Lowering playground density can be an effective intervention for decreasing children’s sedentary time and increasing their physical activity levels during recess; especially in least active children. PMID:24325655

Need for and Access to Supportive Services in the Child Welfare System

PubMed Central

Freisthler, Bridget

2011-01-01

Objective The purpose of this paper is to examine how geographical availability of social services is related to foster care entry rates and referrals for child maltreatment investigations. The primary concerns are to (1) determine locations across Los Angeles County where the availability of social services is low but display a high need for those services and (2) begin to examine how the geographic distribution of social services is related to rates of referrals and foster care entries in child maltreatment. Methods Archival data for all 288 zip codes within Los Angeles County were collected on rates of referrals, foster care entries, location and types of social service agencies, and zip code demographics. Data were analyzed using point process models and spatial regressions. Results Higher densities of child welfare services in local areas (for referrals) and lagged areas (for referrals and foster care entries) were related to lower rates of child maltreatment. The density of housing and housing-related services was negatively related to referrals in local areas and foster care entry rates in lagged areas. Areas with higher densities of substance abuse and domestic violence service agencies had significantly higher rates of both Child Protective Services (CPS) referrals and entries into foster care in local areas. Conclusions While the total density of child welfare services within and surrounding zip code areas is related to lower rates of referrals and foster care entries, the findings are less clear about what those specific services are. Living in and around “resource rich” zip codes may reduce rates of child maltreatment. PMID:23788827

Quantitative analysis of the text and graphic content in ophthalmic slide presentations.

PubMed

Ing, Edsel; Celo, Erdit; Ing, Royce; Weisbrod, Lawrence; Ing, Mercedes

2017-04-01

To determine the characteristics of ophthalmic digital slide presentations. Retrospective quantitative analysis. Slide presentations from a 2015 Canadian primary eye care conference were analyzed for their duration, character and word count, font size, words per minute (wpm), lines per slide, words per slide, slides per minute (spm), text density product (wpm × spm), proportion of graphic content, and Flesch Reading Ease (FRE) score using Microsoft PowerPoint and Word. The median audience evaluation score for the lectures was used to dichotomize the higher scoring lectures (HSL) from the lower scoring lectures (LSL). A priori we hypothesized that there would be a difference in the wpm, spm, text density product, and FRE score between HSL and LSL. Wilcoxon rank-sum tests with Bonferroni correction were utilized. The 17 lectures had medians of 2.5 spm, 20.3 words per slide, 5.0 lines per slide, 28-point sans serif font, 36% graphic content, and text density product of 136.4 words × slides/minute 2 . Although not statistically significant, the HSL had more wpm, fewer words per slide, more graphics per slide, greater text density, and higher FRE score than LSL. There was a statistically significant difference in the spm of the HSL (3.1 ± 1.0) versus the LSL (2.2 ± 1.0) at p = 0.0124. All presenters showed more than 1 slide per minute. The HSL showed more spm than the LSL. The descriptive statistics from this study may aid in the preparation of slides used for teaching and conferences. Copyright © 2017 Canadian Ophthalmological Society. Published by Elsevier Inc. All rights reserved.

A Quick Method for Determining the Density of Single Crystals.

ERIC Educational Resources Information Center

Roman, Pascual; Gutierrez-Zorrilla, Juan M.

1985-01-01

Shows how the Archimedes method is used to determine the density of a single crystal of ammonium oxalate monohydrate. Also shows how to calculate the density of other chemicals when they are available as single crystals. Experimental procedures and materials needed are included. (JN)

Density of Electronic States in the Conduction Band of Ultrathin Films of Naphthalenedicarboxylic Anhydride and Naphthalenetetracarboxylic Dianhydride on the Surface of Oxidized Silicon

NASA Astrophysics Data System (ADS)

Komolov, A. S.; Lazneva, E. F.; Gerasimova, N. B.; Panina, Yu. A.; Baramygin, A. V.; Zashikhin, G. D.; Pshenichnyuk, S. A.

2018-04-01

The results of examination of the electronic structure of the conduction band of naphthalenedicarboxylic anhydride (NDCA) films in the process of their deposition on the surface of oxidized silicon are presented. These results were obtained using total current spectroscopy (TCS) in the energy range from 5 to 20 eV above the Fermi level. The energy position of the primary maxima of the density of unoccupied states (DOUS) of an NDCA film was determined based on the experimental TCS data and calculated data and compared with the position of the DOUS maxima of a naphthalenetetracarboxylic dianhydride (NTCDA) film. The theoretical analysis involved calculating the energies and the spatial distribution of orbitals of the molecules under study at the B3LYP/6-31G(d) DFT (density functional theory) level and correcting the obtained energies in accordance with the procedure that was proven effective in earlier studies of the conduction band of films of small conjugated organic molecules. It was found that the DOUS maxima of the NTCDA film in the studied energy interval from 5 to 20 eV above the Fermi level are shifted toward lower electron energies by 1-2 eV relative to the corresponding DOUS maxima of the NDCA film Subdivision of the Ufa Federal Research Centre of the.

Association between Vitamin D and Circulating Lipids in Early Childhood

PubMed Central

Birken, Catherine S.; Lebovic, Gerald; Anderson, Laura N.; McCrindle, Brian W.; Mamdani, Muhammad; Kandasamy, Sharmilaa; Khovratovich, Marina; Parkin, Patricia C.; Maguire, Jonathon L.

2015-01-01

Vitamin D is associated with established cardiovascular risk factors such as low density lipoprotein (LDL) in adults. It is unknown whether these associations are present in early childhood. To determine whether serum 25-hydroxyvitamin D (25(OH)D) is associated with serum non-high density lipoprotein (non-HDL) cholesterol during early childhood we conducted a cross-sectional study of children aged 1 to 5 years. Healthy children were recruited through the TARGet Kids! practice based research network from 2008-2011 (n=1,961). The associations between 25(OH)D and non-fasting non-HDL cholesterol (the primary endpoint), total cholesterol, triglycerides, HDL, and low density lipoprotein (LDL) cholesterol, were evaluated using multiple linear regression adjusted for age, sex, skin pigmentation, milk intake, vitamin D supplementation, season, body mass index, outdoor play, and screen time. Each 10 nmol/L increase in 25(OH)D was associated with a decrease in non-HDL cholesterol concentration of -0.89 mg/dl (95% CI: -1.16,-0.50), total cholesterol of -1.08 mg/dl (95%CI: -1.49,-0.70), and triglycerides of -2.34 mg/dl (95%CI: -3.23,-1.45). The associations between 25(OH)D and LDL and HDL were not statistically significant. 25(OH)D concentrations were inversely associated with circulating lipids in early childhood, suggesting that vitamin D exposure in early life may be an early modifiable risk factor for cardiovascular disease. PMID:26176958

Endothelin-a receptor antagonist treatment improves the periosteal microcirculation after hindlimb ischemia and reperfusion in the rat.

PubMed

Wolfárd, Antal; Császár, József; Gera, László; Petri, András; Simonka, János Aurél; Balogh, Adáa; Boros, Mihály

2002-12-01

To examine the microcirculatory changes in the rat tibial periosteum after hindlimb ischemia and reperfusion and to evaluate the effects of endothelin-A (ET-A) receptor antagonist therapy in this condition. The healing and functioning of vascularized bone autografts depend mainly on the patency of the microcirculation, and the activation of ET-A receptors may be an important component of the tissue response that occurs during ischemia-reoxygenation injuries. Wistar rats were subjected to 1 hour of hindlimb ischemia and 3 hours of reperfusion. The periosteal microcirculation was visualized by intravital fluorescence microscopy. The leukocyte rolling and adherence in the postcapillary venules and the functional capillary density of the periosteum were determined. Two separate groups were treated with the selective ET-A receptor antagonist BQ 610 or the novel ET-A receptor antagonist ETR-p1/fl peptide at the onset of reperfusion. Reperfusion was accompanied by a significant decrease in functional capillary density and by an increase in the primary and secondary leukocyte-endothelial cell interactions. ET-A receptor inhibition reduced the leukocyte rolling and firm adherence and attenuated the decrease in functional capillary density in both treated groups. ET-1 plays a major role in microvascular dysfunction in the periosteum during reperfusion. The ET-1-ET-A receptor system might be an important target for tissue salvage therapy in transplantation surgery.

Green neighborhoods, food retail and childhood overweight: differences by population density.

PubMed

Liu, Gilbert C; Wilson, Jeffrey S; Qi, Rong; Ying, Jun

2007-01-01

This study examines relationships between overweight in children and two environmentalfactors--amount of vegetation surrounding a child's place of residence and proximity of the child's residence to various types of food retail locations. We hypothesize that living in greener neighborhoods, farther from fast food restaurants, and closer to supermarkets would be associated with lower risk of overweight. Cross-sectional study. Network of primary care pediatric clinics in Marion County, Indiana. We acquired data for 7334 subjects, ages 3 to 18 years, presenting for routine well-child care. Neighborhood vegetation and proximity to food retail were calculated using geographic information systems for each subject using circular and network buffers. Child weight status was defined using body mass index percentiles. Analysis. We used cumulative logit models to examine associations between an index of overweight, neighborhood vegetation, and food retail environment. After controlling for individual socio-demographics and neighborhood socioeconomic status, measures of vegetation and food retail significantly predicted overweight in children. Increased neighborhood vegetation was associated with decreased risk for overweight, but only for subjects residing in higher population density regions. Increased distance between a subject's residence and the nearest large brand name supermarkets was associated with increased risk of overweight, but only for subjects residing in lower population density regions. This research suggests that aspects of the built environment are determinants of child weight status, ostensibly by influencing physical activity and dietary behaviors.

Micro CT based truth estimation of nodule volume

NASA Astrophysics Data System (ADS)

Kinnard, L. M.; Gavrielides, M. A.; Myers, K. J.; Zeng, R.; Whiting, B.; Lin-Gibson, S.; Petrick, N.

2010-03-01

With the advent of high-resolution CT, three-dimensional (3D) methods for nodule volumetry have been introduced, with the hope that such methods will be more accurate and consistent than currently used planar measures of size. However, the error associated with volume estimation methods still needs to be quantified. Volume estimation error is multi-faceted in the sense that there is variability associated with the patient, the software tool and the CT system. A primary goal of our current research efforts is to quantify the various sources of measurement error and, when possible, minimize their effects. In order to assess the bias of an estimate, the actual value, or "truth," must be known. In this work we investigate the reliability of micro CT to determine the "true" volume of synthetic nodules. The advantage of micro CT over other truthing methods is that it can provide both absolute volume and shape information in a single measurement. In the current study we compare micro CT volume truth to weight-density truth for spherical, elliptical, spiculated and lobulated nodules with diameters from 5 to 40 mm, and densities of -630 and +100 HU. The percent differences between micro CT and weight-density volume for -630 HU nodules range from [-21.7%, -0.6%] (mean= -11.9%) and the differences for +100 HU nodules range from [-0.9%, 3.0%] (mean=1.7%).

Influence of trabecular bone quality and implantation direction on press-fit mechanics.

PubMed

Damm, Niklas B; Morlock, Michael M; Bishop, Nicholas E

2017-02-01

Achieving primary stability of uncemented press-fit prostheses in patients with poor quality bone can involve axial implantation forces large enough to cause bone fracture. Radial implantation eliminates intraoperative impaction forces and could prevent this damage. Platens of two commercial implant surfaces ("Beaded" and "Flaked") were implanted onto trabecular bone specimens of varying quality in a press-fit simulator. Samples were implanted with varying interference, either axially (shear) or radially (normal). Push-in and pull-out forces were measured to assess stability. Microstructural changes in the bone were determined from μCT analysis. For force-defined implantation analysis, push-in and pull-out forces both increased proportionally with increasing radial force, independent of implantation direction, bone quality or implant surface. For position-defined implantation analysis, pull-out forces were generally found to increase with interference and to be greater for radial than axial implantation direction, and to be lower for poor quality bone. Bone density increased locally at the tested interface due to implantation, in particular for the Beaded surface under axial implantation. If a safe radial stress can be determined for cortical bone in a particular patient, the associated implantation force, and pull-out force which represents primary stability, can be directly derived, regardless of implantation direction, bone quality or implant surface. Radial implantation delivers primary stability that is no worse than that for axial implantation and may eliminate potentially damaging impaction forces. Development of implant designs based on this principal might improve implant fixation. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:224-233, 2017. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Untangling ciliary access and enrichment of two rhodopsin-like receptors using quantitative fluorescence microscopy reveals cell-specific sorting pathways.

PubMed

Geneva, Ivayla I; Tan, Han Yen; Calvert, Peter D

2017-02-15

Resolution limitations of optical systems are major obstacles for determining whether proteins are enriched within cell compartments. Here we use an approach to determine the degree of membrane protein ciliary enrichment that quantitatively accounts for the differences in sampling of the ciliary and apical membranes inherent to confocal microscopes. Theory shows that cilia will appear more than threefold brighter than the surrounding apical membrane when the densities of fluorescently labeled proteins are the same, thus providing a benchmark for ciliary enrichment. Using this benchmark, we examined the ciliary enrichment signals of two G protein-coupled receptors (GPCRs)-the somatostatin receptor 3 and rhodopsin. Remarkably, we found that the C-terminal VxPx motif, required for efficient enrichment of rhodopsin within rod photoreceptor sensory cilia, inhibited enrichment of the somatostatin receptor in primary cilia. Similarly, VxPx inhibited primary cilium enrichment of a chimera of rhodopsin and somatostatin receptor 3, where the dual Ax(S/A)xQ ciliary targeting motifs within the third intracellular loop of the somatostatin receptor replaced the third intracellular loop of rhodopsin. Rhodopsin was depleted from primary cilia but gained access, without being enriched, with the dual Ax(S/A)xQ motifs. Ciliary enrichment of these GPCRs thus operates via distinct mechanisms in different cells. © 2017 Geneva et al. This article is distributed by The American Society for Cell Biology under license from the author(s). Two months after publication it is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

X-ray tomography as a non-destructive tool for evaluating the preservation of primary isotope signatures and mineralogy of Mesozoic fossils

NASA Astrophysics Data System (ADS)

Santillan, J. D.; Boyce, J. W.; Eagle, R.; Martin, T.; Tuetken, T.; Eiler, J.

2010-12-01

The stable isotope compositions of carbonate and phosphate components in fossil teeth and bone are widely used to infer information on paleoclimate and the physiology of extinct organisms. Recently the potential for measuring the body temperatures of extinct vertebrates from analyses of 13C-18O bond ordering in fossil teeth has been demonstrated (Eagle et al. 2010). The interpretation of these isotopic signatures relies on an assessment of the resistance of fossil bioapatite to alteration, as diffusion within, and partial recrystallization, or replacement of the original bioapatite will lead to measured compositions that represent mixtures between primary and secondary phases and/or otherwise inaccurate apparent temperatures. X-ray computed tomography (CT) allows 3-D density maps of teeth to be made at micron-scale resolution. Such density maps have the potential to record textural evidence for alteration, recrystallization, or replacement of enamel. Because it is non-destructive, CT can be used prior to stable isotope analysis to identify potentially problematic samples without consuming or damaging scientifically significant specimens. As a test, we have applied CT to tooth fragments containing both dentin and enamel from Late Jurassic sauropods and a Late Cretaceous theropod that yielded a range of clumped isotope temperatures from anomalously high ˜60oC to physiologically plausible ≤40oC. This range of temperatures suggests partial, high-temperature modification of some specimens, but possible preservation of primary signals in others. Three-dimensional CT volumes generated using General Electric Phoenix|x-ray CT instruments were compared with visible light and back-scattered electron images of the same samples. The tube-detector combination used for the CT study consisted of a 180 kV nanofocus transmission tube coupled with a 127 micron pixel pitch detector ( ˜3-12μ m voxel edges), allowing us to clearly map out alteration zones in high contrast, while reducing edge effects and beam hardening artifacts. CT images of these teeth show a range of replacement textures. One tooth -- thought to be the least altered -- shows only localized positive density anomalies near fractures, while a second -- thought to be highly altered -- contains high-density replacement mineralization. A third tooth -- one suspected of possible partial alteration -- shows a network of rectilinear density anomalies in the enamel similar to 2-D transmitted light and back-scattered electron images. This may represent recrystallization or replacement of the primary bioapatite. Unlike 2-D imaging techniques, 3-D volumes can be used to quickly and easily make quantitative measurements of the volumes of altered and unaltered materials: For example, in the enamel of sample 3, we observe a ratio of high density to low density material of ˜ 3:2.

Reformulation of Density Functional Theory for N-Representable Densities and the Resolution of the v-Representability Problem

DOE PAGES

Gonis, A.; Zhang, X. G.; Stocks, G. M.; ...

2015-10-23

Density functional theory for the case of general, N-representable densities is reformulated in terms of density functional derivatives of expectation values of operators evaluated with wave functions leading to a density, making no reference to the concept of potential. The developments provide a complete solution of the v-representability problem by establishing a mathematical procedure that determines whether a density is v-representable and in the case of an affirmative answer determines the potential (within an additive constant) as a derivative with respect to the density of a constrained search functional. It also establishes the existence of an energy functional of themore » density that, for v-representable densities, assumes its minimum value at the density describing the ground state of an interacting many-particle system. The theorems of Hohenberg and Kohn emerge as special cases of the formalism.« less

Viscosity and density of methanol/water mixtures at low temperatures

NASA Technical Reports Server (NTRS)

Austin, J. G.; Kurata, F.; Swift, G. W.

1968-01-01

Viscosity and density are measured at low temperatures for three methanol/water mixtures. Viscosity is determined by a modified falling cylinder method or a calibrated viscometer. Density is determined by the volume of each mixture contained in a calibrated glass cell placed in a constant-temperature bath.

Evaluation of techniques for determining the density of fine woody debris

Treesearch

Becky Fasth; Mark E. Harmon; Christopher W. Woodall; Jay. Sexton

2010-01-01

Evaluated various techniques for determining the density (i.e., bulk density) of fine woody debris during forest inventory activities. It was found that only experts in dead wood inventory may be able to identify fine woody debris stages of decay. Suggests various future research directions such as...

The Wang Landau parallel algorithm for the simple grids. Optimizing OpenMPI parallel implementation

NASA Astrophysics Data System (ADS)

Kussainov, A. S.

2017-12-01

The Wang Landau Monte Carlo algorithm to calculate density of states for the different simple spin lattices was implemented. The energy space was split between the individual threads and balanced according to the expected runtime for the individual processes. Custom spin clustering mechanism, necessary for overcoming of the critical slowdown in the certain energy subspaces, was devised. Stable reconstruction of the density of states was of primary importance. Some data post-processing techniques were involved to produce the expected smooth density of states.

Determination of grain size distribution function using two-dimensional Fourier transforms of tone pulse encoded images

NASA Technical Reports Server (NTRS)

Generazio, E. R.

1986-01-01

Microstructural images may be tone pulse encoded and subsequently Fourier transformed to determine the two-dimensional density of frequency components. A theory is developed relating the density of frequency components to the density of length components. The density of length components corresponds directly to the actual grain size distribution function from which the mean grain shape, size, and orientation can be obtained.

On a new scenario for the saturation of the low-threshold two-plasmon parametric decay instability of an extraordinary wave in the inhomogeneous plasma of magnetic traps

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gusakov, E. Z., E-mail: Evgeniy.Gusakov@mail.ioffe.ru; Popov, A. Yu., E-mail: a.popov@mail.ioffe.ru; Irzak, M. A., E-mail: irzak@mail.ioffe.ru

The most probable scenario for the saturation of the low-threshold two-plasmon parametric decay instability of an electron cyclotron extraordinary wave has been analyzed. Within this scenario two upperhybrid plasmons at frequencies close to half the pump wave frequency radially trapped in the vicinity of the local maximum of the plasma density profile are excited due to the excitation of primary instability. The primary instability saturation results from the decays of the daughter upper-hybrid waves into secondary upperhybrid waves that are also radially trapped in the vicinity of the local maximum of the plasma density profile and ion Bernstein waves.

Three-dimensional coordinates of individual atoms in materials revealed by electron tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Rui; Chen, Chien-Chun; Wu, Li

Crystallography, the primary method for determining the 3D atomic positions in crystals, has been fundamental to the development of many fields of science. However, the atomic positions obtained from crystallography represent a global average of many unit cells in a crystal. In this paper, we report, for the first time, the determination of the 3D coordinates of thousands of individual atoms and a point defect in a material by electron tomography with a precision of ~19 pm, where the crystallinity of the material is not assumed. From the coordinates of these individual atoms, we measure the atomic displacement field andmore » the full strain tensor with a 3D resolution of ~1 nm 3 and a precision of ~10 -3, which are further verified by density functional theory calculations and molecular dynamics simulations. Finally, the ability to precisely localize the 3D coordinates of individual atoms in materials without assuming crystallinity is expected to find important applications in materials science, nanoscience, physics, chemistry and biology.« less

Three-dimensional coordinates of individual atoms in materials revealed by electron tomography

DOE PAGES

Xu, Rui; Chen, Chien-Chun; Wu, Li; ...

2015-09-21

Crystallography, the primary method for determining the 3D atomic positions in crystals, has been fundamental to the development of many fields of science. However, the atomic positions obtained from crystallography represent a global average of many unit cells in a crystal. In this paper, we report, for the first time, the determination of the 3D coordinates of thousands of individual atoms and a point defect in a material by electron tomography with a precision of ~19 pm, where the crystallinity of the material is not assumed. From the coordinates of these individual atoms, we measure the atomic displacement field andmore » the full strain tensor with a 3D resolution of ~1 nm 3 and a precision of ~10 -3, which are further verified by density functional theory calculations and molecular dynamics simulations. Finally, the ability to precisely localize the 3D coordinates of individual atoms in materials without assuming crystallinity is expected to find important applications in materials science, nanoscience, physics, chemistry and biology.« less

Determination of Critical Parameters Based on the Intensity of Transmitted Light Around Gas-Liquid Interface: Critical Parameters of CO

NASA Astrophysics Data System (ADS)

Nakayama, Masaki; Katano, Hiroaki; Sato, Haruki

2014-05-01

A precise determination of the critical temperature and density for technically important fluids would be possible on the basis of the digital image for the visual observation of the phase boundary in the vicinity of the critical point since the sensitivity and resolution are higher than those of naked eyes. In addition, the digital image can avoid the personal uncertainty of an observer. A strong density gradient occurs in a sample cell at the critical point due to gravity. It was carefully assessed to determine the critical density, where the density profile in the sample cell can be observed from the luminance profile of a digital image. The density-gradient profile becomes symmetric at the critical point. One of the best fluids, whose thermodynamic properties have been measured with the highest reliability among technically important fluids, would be carbon dioxide. In order to confirm the reliability of the proposed method, the critical temperature and density of carbon dioxide were determined using the digital image. The critical temperature and density values of carbon dioxide are ( and ( kg m, respectively. The critical temperature and density values agree with the existing best values within estimated uncertainties. The reliability of the method was confirmed. The critical pressure, 7.3795 MPa, corresponding to the determined critical temperature of 304.143 K is also proposed. A new set of parameters for the vapor-pressure equation is also provided.

Micro-computed tomographic analysis of progression of artificial enamel lesions in primary and permanent teeth after resin infiltration.

PubMed

Ozgul, Betul Memis; Orhan, Kaan; Oz, Firdevs Tulga

2015-09-01

We investigated inhibition of lesion progression in artificial enamel lesions. Lesions were created on primary and permanent anterior teeth (n = 10 each) and were divided randomly into two groups with two windows: Group 1 (window A: resin infiltration; window B: negative control) and Group 2 (window A: resin infiltration + fluoride varnish; window B: fluoride varnish). After pH cycling, micro-computed tomography was used to analyze progression of lesion depth and changes in mineral density. Resin infiltration and resin infiltration + fluoride varnish significantly inhibited progression of lesion depth in primary teeth (P < 0.05). Inhibition of lesion depth progression in permanent teeth was significantly greater after treatment with resin infiltration + fluoride varnish than in the negative control (P < 0.05). Change in mineral density was smaller in the resin infiltration and resin infiltration + fluoride varnish groups; however, the difference was not significant for either group (P > 0.05). Resin infiltration is a promising method of inhibiting progression of caries lesions.

Effects of national antibiotic stewardship and infection control strategies on hospital-associated and community-associated meticillin-resistant Staphylococcus aureus infections across a region of Scotland: a non-linear time-series study.

PubMed

Lawes, Timothy; Lopez-Lozano, José-María; Nebot, Cesar A; Macartney, Gillian; Subbarao-Sharma, Rashmi; Dare, Ceri Rj; Wares, Karen D; Gould, Ian M

2015-12-01

Restriction of antibiotic consumption to below predefined total use thresholds might remove the selection pressure that maintains antimicrobial resistance within populations. We assessed the effect of national antibiotic stewardship and infection prevention and control programmes on prevalence density of meticillin-resistant Staphylococcus aureus (MRSA) infections across a region of Scotland. This non-linear time-series analysis and quasi-experimental study explored ecological determinants of MRSA epidemiology among 1,289,929 hospital admissions and 455,508 adults registered in primary care in northeast Scotland. Interventions included antibiotic stewardship to restrict use of so-called 4C (cephalosporins, co-amoxiclav, clindamycin, and fluoroquinolones) and macrolide antibiotics; a hand hygiene campaign; hospital environment inspections; and MRSA admission screening. Total effects were defined as the difference between scenarios with intervention (observed) and without intervention (predicted from time-series models). The primary outcomes were prevalence density of MRSA infections per 1000 occupied bed days (OBDs) in hospitals or per 10,000 inhabitants per day (IDs) in the community. During antibiotic stewardship, use of 4C and macrolide antibiotics fell by 47% (mean decrease 224 defined daily doses [DDDs] per 1000 OBDs, 95% CI 154-305, p=0·008) in hospitals and 27% (mean decrease 2·52 DDDs per 1000 IDs, 0·65-4·55, p=0·031) in the community. Hospital prevalence densities of MRSA were inversely related to intensified infection prevention and control, but positively associated with MRSA rates in neighbouring hospitals, importation pressures, bed occupancy, and use of fluoroquinolones, co-amoxiclav, and third-generation cephalosporins, or macrolide antibiotics that exceeded hospital-specific thresholds. Community prevalence density was predicted by hospital MRSA rates and above-threshold use of macrolides, fluoroquinolones, and clindamycin. MRSA prevalence density decreased during antibiotic stewardship by 54% (mean reduction 0·60 per 1000 OBDs, 0·01-1·18, p=0·049) in hospital and 37% (mean reduction 0·017 per 10,000 IDs, 0·004-0·029, p=0·012) in the community. Combined with infection prevention and control measures, MRSA prevalence density was reduced by 50% (absolute difference 0·94 cases per 1000 OBDs, 0·27-1·62, p=0·006) in hospitals and 47% (absolute difference 0·033 cases per 10,000 IDs, 0·018-0·048, p<0·0001) in the community. Alongside infection control measures, removal of key antibiotic selection pressures during a national antibiotic stewardship intervention predicted large and sustained reductions in hospital-associated and community-associated MRSA. NHS Grampian Research & Development Fund. Copyright © 2015 Elsevier Ltd. All rights reserved.

Wolbachia density changes seasonally amongst populations of the pale grass blue butterfly, Zizeeria maha (Lepidoptera: Lycaenidae)

PubMed Central

Sumi, Takuto; Miura, Kazuki; Miyatake, Takahisa

2017-01-01

Previous studies showed that the survival rate of Wolbachia decreases under high temperature in incubators. It is also known that a high density of Wolbachia in the host body reduces the host emergence rate, while low densities fail to change reproduction rates. However, few studies have examined the density of Wolbachia in hosts in the field. Here, we focus on Wolbachia infection of the pale grass blue butterfly, Zizeeria maha (Lepidoptera: Lycaenidae), which is distributed throughout the Japanese islands. We examined the rate and density of Wolbachia infection in the bodies of butterflies at thirteen locations in Japan. At seven of these places, we collected butterflies in different seasons to determine seasonal differences in the infection rate and density and found that Wolbachia density has seasonal differences within the same population. Moreover, to determine whether Wolbachia density has a geographical cline, we compared the infection density of Wolbachia amongst all geographical populations. In addition, we determined the sequences of Wolbachia wsp and host mtDNA CO1 haplotypes of all populations. The results showed that Wolbachia density increased in early summer and decreased in autumn. Further, the density of Wolbachia infecting the same strain of Z. maha varied amongst populations, although no tendency in geographical cline was observed. PMID:28403227

Comparison of density determination of liquid samples by density meters

NASA Astrophysics Data System (ADS)

Buchner, C.; Wolf, H.; Vámossy, C.; Lorefice, S.; Lenard, E.; Spohr, I.; Mares, G.; Perkin, M.; Parlic-Risovic, T.; Grue, L.-L.; Tammik, K.; van Andel, I.; Zelenka, Z.

2016-01-01

Hydrostatic density determinations of liquids as reference material are mainly performed by National Metrology Institutes to provide means for calibrating or checking liquid density measuring instruments such as oscillation-type density meters. These density meters are used by most of the metrology institutes for their calibration and scientific work. The aim of this project was to compare the results of the liquid density determination by oscillating density meters of the participating laboratories. The results were linked to CCM.D.K-2 partly via Project EURAMET.M.D.K-2 (1019) "Comparison of liquid density standards" by hydrostatic weighing piloted by BEV in 2008. In this comparison pentadecane, water and of oil with a high viscosity were measured at atmospheric pressure using oscillation type density meter. The temperature range was from 15 °C to 40 °C. The measurement results were in some cases discrepant. Further studies, comparisons are essential to explore the capability and uncertainty of the density meters Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Wolbachia density changes seasonally amongst populations of the pale grass blue butterfly, Zizeeria maha (Lepidoptera: Lycaenidae).

PubMed

Sumi, Takuto; Miura, Kazuki; Miyatake, Takahisa

2017-01-01

Previous studies showed that the survival rate of Wolbachia decreases under high temperature in incubators. It is also known that a high density of Wolbachia in the host body reduces the host emergence rate, while low densities fail to change reproduction rates. However, few studies have examined the density of Wolbachia in hosts in the field. Here, we focus on Wolbachia infection of the pale grass blue butterfly, Zizeeria maha (Lepidoptera: Lycaenidae), which is distributed throughout the Japanese islands. We examined the rate and density of Wolbachia infection in the bodies of butterflies at thirteen locations in Japan. At seven of these places, we collected butterflies in different seasons to determine seasonal differences in the infection rate and density and found that Wolbachia density has seasonal differences within the same population. Moreover, to determine whether Wolbachia density has a geographical cline, we compared the infection density of Wolbachia amongst all geographical populations. In addition, we determined the sequences of Wolbachia wsp and host mtDNA CO1 haplotypes of all populations. The results showed that Wolbachia density increased in early summer and decreased in autumn. Further, the density of Wolbachia infecting the same strain of Z. maha varied amongst populations, although no tendency in geographical cline was observed.

A straightforward method for measuring the range of apparent density of microplastics.

PubMed

Li, Lingyun; Li, Mengmeng; Deng, Hua; Cai, Li; Cai, Huiwen; Yan, Beizhan; Hu, Jun; Shi, Huahong

2018-10-15

Density of microplastics has been regarded as the primary property that affect the distribution and bioavailability of microplastics in the water column. For measuring the density of microplastis, we developed a simple and rapid method based on density gradient solutions. In this study, we tested four solvents to make the density gradient solutions, i.e., ethanol (0.8 g/cm 3 ), ultrapure water (1.0 g/cm 3 ), saturated NaI (1.8 g/cm 3 ) and ZnCl 2 (1.8 g/cm 3 ). Density of microplastics was measured via observing the float or sink status in the density gradient solutions. We found that density gradient solutions made from ZnCl 2 had a larger uncertainty in measuring density than that from NaI, most likely due to a higher surface tension of ZnCl 2 solution. Solutions made from ethanol, ultrapure water, and NaI showed consistent density results with listed densities of commercial products, indicating that these density gradient solutions were suitable for measuring microplastics with a density range of 0.8-1.8 g/cm 3 . Copyright © 2018 Elsevier B.V. All rights reserved.

Modeling Neutral Densities Downstream of a Gridded Ion Thruster

NASA Technical Reports Server (NTRS)

Soulas, George C.

2010-01-01

The details of a model for determining the neutral density downstream of a gridded ion thruster are presented. An investigation of the possible sources of neutrals emanating from and surrounding a NEXT ion thruster determined that the most significant contributors to the downstream neutral density include discharge chamber neutrals escaping through the perforated grids, neutrals escaping from the neutralizer, and vacuum facility background neutrals. For the neutral flux through the grids, near- and far-field equations are presented for rigorously determining the neutral density downstream of a cylindrical aperture. These equations are integrated into a spherically-domed convex grid geometry with a hexagonal array of apertures for determining neutral densities downstream of the ion thruster grids. The neutrals escaping from an off-center neutralizer are also modeled assuming diffuse neutral emission from the neutralizer keeper orifice. Finally, the effect of the surrounding vacuum facility neutrals is included and assumed to be constant. The model is used to predict the neutral density downstream of a NEXT ion thruster with and without neutralizer flow and a vacuum facility background pressure. The impacts of past simplifying assumptions for predicting downstream neutral densities are also examined for a NEXT ion thruster.

Linear Stability Analysis of Gravitational Effects on a Low-Density Gas Jet Injected into a High-Density Medium

NASA Technical Reports Server (NTRS)

Lawson, Anthony L.; Parthasarathy, Ramkumar N.

2005-01-01

The objective of this study was to determine the effects of buoyancy on the absolute instability of low-density gas jets injected into high-density gas mediums. Most of the existing analyses of low-density gas jets injected into a high-density ambient have been carried out neglecting effects of gravity. In order to investigate the influence of gravity on the near-injector development of the flow, a spatio-temporal stability analysis of a low-density round jet injected into a high-density ambient gas was performed. The flow was assumed to be isothermal and locally parallel; viscous and diffusive effects were ignored. The variables were represented as the sum of the mean value and a normal-mode small disturbance. An ordinary differential equation governing the amplitude of the pressure disturbance was derived. The velocity and density profiles in the shear layer, and the Froude number (signifying the effects of gravity) were the three important parameters in this equation. Together with the boundary conditions, an eigenvalue problem was formulated. Assuming that the velocity and density profiles in the shear layer to be represented by hyperbolic tangent functions, the eigenvalue problem was solved for various values of Froude number. The Briggs-Bers criterion was combined with the spatio-temporal stability analysis to determine the nature of the absolute instability of the jet whether absolutely or convectively unstable. The roles of the density ratio, Froude number, Schmidt number, and the lateral shift between the density and velocity profiles on the absolute instability of the jet were determined. Comparisons of the results with previous experimental studies show good agreement when the effects of these variables are combined together. Thus, the combination of these variables determines how absolutely unstable the jet will be.

Evaluation of Density Corrections to Methane Fluxes Measured by Open-Path Eddy Covariance over Contrasting Landscapes

NASA Astrophysics Data System (ADS)

Chamberlain, Samuel D.; Verfaillie, Joseph; Eichelmann, Elke; Hemes, Kyle S.; Baldocchi, Dennis D.

2017-11-01

Corrections accounting for air density fluctuations due to heat and water vapour fluxes must be applied to the measurement of eddy-covariance fluxes when using open-path sensors. Experimental tests and ecosystem observations have demonstrated the important role density corrections play in accurately quantifying carbon dioxide (CO2) fluxes, but less attention has been paid to evaluating these corrections for methane (CH4) fluxes. We measured CH4 fluxes with open-path sensors over a suite of sites with contrasting CH4 emissions and energy partitioning, including a pavement airfield, two negligible-flux ecosystems (drained alfalfa and pasture), and two high-flux ecosystems (flooded wetland and rice). We found that density corrections successfully re-zeroed fluxes in negligible-flux sites; however, slight overcorrection was observed above pavement. The primary impact of density corrections varied over negligible- and high-flux ecosystems. For negligible-flux sites, corrections led to greater than 100% adjustment in daily budgets, while these adjustments were only 3-10% in high-flux ecosystems. The primary impact to high-flux ecosystems was a change in flux diel patterns, which may affect the evaluation of relationships between biophysical drivers and fluxes if correction bias exists. Additionally, accounting for density effects to high-frequency CH4 fluctuations led to large differences in observed CH4 flux cospectra above negligible-flux sites, demonstrating that similar adjustments should be made before interpreting CH4 cospectra for comparable ecosystems. These results give us confidence in CH4 fluxes measured by open-path sensors, and demonstrate that density corrections play an important role in adjusting flux budgets and diel patterns across a range of ecosystems.

Neuron density is decreased in the prefrontal cortex in Williams syndrome.

PubMed

Lew, Caroline Horton; Brown, Chelsea; Bellugi, Ursula; Semendeferi, Katerina

2017-01-01

Williams Syndrome (WS) is a rare neurodevelopmental disorder associated with a hemideletion in chromosome 7, which manifests a distinct behavioral phenotype characterized by a hyperaffiliative social drive, in striking contrast to the social avoidance behaviors that are common in Autism Spectrum Disorder (ASD). MRI studies have observed structural and functional abnormalities in WS cortex, including the prefrontal cortex (PFC), a region implicated in social cognition. This study utilizes the Bellugi Williams Syndrome Brain Collection, a unique resource that comprises the largest WS postmortem brain collection in existence, and is the first to quantitatively examine WS PFC cytoarchitecture. We measured neuron density in layers II/III and V/VI of five cortical areas: PFC areas BA 10 and BA 11, primary motor BA 4, primary somatosensory BA 3, and visual area BA 18 in six matched pairs of WS and typically developing (TD) controls. Neuron density in PFC was lower in WS relative to TD, with layers V/VI demonstrating the largest decrease in density, reaching statistical significance in BA 10. In contrast, BA 3 and BA 18 demonstrated a higher density in WS compared to TD, although this difference was not statistically significant. Neuron density in BA 4 was similar in WS and TD. While other cortical areas were altered in WS, prefrontal areas appeared to be most affected. Neuron density is also altered in the PFC of individuals with ASD. Together these findings suggest that the PFC is targeted in neurodevelopmental disorders associated with sociobehavioral alterations. Autism Res 2017, 10: 99-112. © 2016 International Society for Autism Research, Wiley Periodicals, Inc. © 2016 International Society for Autism Research, Wiley Periodicals, Inc.

Factors Affecting Salamander Density and Distribution within Four Forest Types in Southern Appalachian Mountains

Treesearch

Craig A. Harper; David C. Guynn

1999-01-01

We used a terrestrial vacuum to sample known area plots in order to obtain density estimates of salamanders and their primary prey, invertebrates of the forest floor. We sampled leaf litter and measured various vegetative and topographic parameters within four forest types (oak-pine, oak-hickory, mixed mesophytic and northern hardwoods) and three age classes (0-12,13-...

Effect of Primary-Ion Current Density on Charge Compensation in SIMS Analysis of a Quartz Glass

NASA Astrophysics Data System (ADS)

Inoue, Kazuyuki; Isogai, Akio

1988-05-01

In secondary ion mass spectrometry (SIMS) analysis of a quartz glass by means of negative ion bombardment, the effect of the negative ion current density (Ji) has been investigated. The results show that under lower Ji (<20 μA/cm2), time is required to compensate for the surface charge and the time is inversely proportional to Ji.

Primary Prevention of Asthma: Age and Sex Influence Sensitivity to Allergen-Induced Airway Inflammation and Contribute to Asthma Heterogeneity in Guinea Pigs

PubMed Central

Regal, Jean F.; Regal, Ronald R.; Meehan, Jessica L.; Mohrman, Margaret E.

2010-01-01

Background Limiting allergen exposure in the sensitization phase has been proposed as a means of primary prevention of asthma, but its effectiveness is debated. Hypothesis Primary prevention of asthma is more effective in limiting asthma symptoms in young guinea pigs compared with adults, whether males or females. Methods The following experimental groups were used: young/young, sensitized and challenged before sexual maturity; young/adult, sensitized young and challenged after sexual maturity; adult/adult, sensitized and challenged after sexual maturity. Males and females were sensitized intraperitoneally with varying doses of ovalbumin (OVA) and challenged intratracheally with a constant OVA dose. Cellular infiltration into lung and lavage fluid as well as airway hyperresponsiveness to intravenous methacholine was determined 24 h later. Results In unsensitized animals, density of resident inflammatory cells as well as baseline pulmonary function differed with age and sex. Maximum OVA-induced eosinophilia in females occurred at a lower sensitizing dose of OVA than in males, and the slopes of the dose-response relationship differed significantly between sexes. Young females had more pronounced increases in eosinophils compared with some adult treatment groups. The concentrations of OVA-specific antibodies were not directly related to differences in cellular infiltration. Airway hyperresponsiveness to methacholine challenge was observed in all treatment groups. Conclusion Young animals require major reductions in allergen exposure compared with adults to effectively limit airway inflammation in primary prevention. Heterogeneity of asthma symptoms seen with age and sex suggests that primary prevention by limiting allergen exposure or treatment with anti-inflammatory or bronchodilator drugs may be more effective strategies for specific age and gender populations. PMID:16931886

Primary Hyperparathyroidism: The Influence of Bone Marrow Adipose Tissue on Bone Loss and of Osteocalcin on Insulin Resistance

PubMed Central

Mendonça, Maira L.; Batista, Sérgio L.; Nogueira-Barbosa, Marcello H.; Salmon, Carlos E.G.; de Paula, Francisco J.A.

2016-01-01

OBJECTIVES: Bone marrow adipose tissue has been associated with low bone mineral density. However, no data exist regarding marrow adipose tissue in primary hyperparathyroidism, a disorder associated with bone loss in conditions of high bone turnover. The objective of the present study was to investigate the relationship between marrow adipose tissue, bone mass and parathyroid hormone. The influence of osteocalcin on the homeostasis model assessment of insulin resistance was also evaluated. METHODS: This was a cross-sectional study conducted at a university hospital, involving 18 patients with primary hyperparathyroidism (PHPT) and 21 controls (CG). Bone mass was assessed by dual-energy x-ray absorptiometry and marrow adipose tissue was assessed by 1H magnetic resonance spectroscopy. The biochemical evaluation included the determination of parathyroid hormone, osteocalcin, glucose and insulin levels. RESULTS: A negative association was found between the bone mass at the 1/3 radius and parathyroid hormone levels (r = -0.69; p<0.01). Marrow adipose tissue was not significantly increased in patients (CG = 32.8±11.2% vs PHPT = 38.6±12%). The serum levels of osteocalcin were higher in patients (CG = 8.6±3.6 ng/mL vs PHPT = 36.5±38.4 ng/mL; p<0.005), but no associations were observed between osteocalcin and insulin or between insulin and both marrow adipose tissue and bone mass. CONCLUSION: These results suggest that the increment of adipogenesis in the bone marrow microenvironment under conditions of high bone turnover due to primary hyperparathyroidism is limited. Despite the increased serum levels of osteocalcin due to primary hyperparathyroidism, these patients tend to have impaired insulin sensitivity. PMID:27626477

Fingerprint-Based Structure Retrieval Using Electron Density

PubMed Central

Yin, Shuangye; Dokholyan, Nikolay V.

2010-01-01

We present a computational approach that can quickly search a large protein structural database to identify structures that fit a given electron density, such as determined by cryo-electron microscopy. We use geometric invariants (fingerprints) constructed using 3D Zernike moments to describe the electron density, and reduce the problem of fitting of the structure to the electron density to simple fingerprint comparison. Using this approach, we are able to screen the entire Protein Data Bank and identify structures that fit two experimental electron densities determined by cryo-electron microscopy. PMID:21287628

Fingerprint-based structure retrieval using electron density.

PubMed

Yin, Shuangye; Dokholyan, Nikolay V

2011-03-01

We present a computational approach that can quickly search a large protein structural database to identify structures that fit a given electron density, such as determined by cryo-electron microscopy. We use geometric invariants (fingerprints) constructed using 3D Zernike moments to describe the electron density, and reduce the problem of fitting of the structure to the electron density to simple fingerprint comparison. Using this approach, we are able to screen the entire Protein Data Bank and identify structures that fit two experimental electron densities determined by cryo-electron microscopy. Copyright © 2010 Wiley-Liss, Inc.

Measuring Two Key Parameters of H3 Color Centers in Diamond

NASA Technical Reports Server (NTRS)

Roberts, W. Thomas

2005-01-01

A method of measuring two key parameters of H3 color centers in diamond has been created as part of a continuing effort to develop tunable, continuous-wave, visible lasers that would utilize diamond as the lasing medium. (An H3 color center in a diamond crystal lattice comprises two nitrogen atoms substituted for two carbon atoms bonded to a third carbon atom. H3 color centers can be induced artificially; they also occur naturally. If present in sufficient density, they impart a yellow hue.) The method may also be applicable to the corresponding parameters of other candidate lasing media. One of the parameters is the number density of color centers, which is needed for designing an efficient laser. The other parameter is an optical-absorption cross section, which, as explained below, is needed for determining the number density. The present method represents an improvement over prior methods in which optical-absorption measurements have been used to determine absorption cross sections or number densities. Heretofore, in order to determine a number density from such measurements, it has been necessary to know the applicable absorption cross section; alternatively, to determine the absorption cross section from such measurements, it has been necessary to know the number density. If, as in this case, both the number density and the absorption cross section are initially unknown, then it is impossible to determine either parameter in the absence of additional information.

Quantum Crystallography: Density Matrix-Density Functional Theory and the X-Ray Diffraction Experiment

NASA Astrophysics Data System (ADS)

Soirat, Arnaud J. A.

Density Matrix Theory is a Quantum Mechanical formalism in which the wavefunction is eliminated and its role taken over by reduced density matrices. The interest of this is that, it allows one, in principle, to calculate any electronic property of a physical system, without having to solve the Schrodinger equation, using only two entities much simpler than an N-body wavefunction: first and second -order reduced density matrices. In practice, though, this very promising possibility faces the tremendous theoretical problem of N-representability, which has been solved for the former, but, until now, voids any hope of theoretically determining the latter. However, it has been shown that single determinant reduced density matrices of any order may be recovered from coherent X-ray diffraction data, if one provides a proper Quantum Mechanical description of the Crystallography experiment. A deeper investigation of this method is the purpose of this work, where we, first, further study the calculation of X-ray reduced density matrices N-representable by a single Slater determinant. In this context, we independently derive necessary and sufficient conditions for the uniqueness of the method. We then show how to account for electron correlation in this model. For the first time, indeed, we derive highly accurate, yet practical, density matrices approximately N-representable by correlated-determinant wavefunctions. The interest of such a result lies in the Quantum Mechanical validity of these density matrices, their property of being entirely obtainable from X-ray coherent diffraction data, their very high accuracy conferred by this known property of the N-representing wavefunction, as well as their definition as explicit functionals of the density. All of these properties are finally used in both a theoretical and a numerical application: in the former, we show that these density matrices may be used in the context of Density Functional Theory to highly accurately determine the unknown HK functional, associated with the theorem of Hohenberg and Kohn. The latter is provided by the calculation of helium correlation energy, where we test approximating the second-order density function by the leading term of its McLaurin's series expansion.

The effect of social geographic factors on the untreated tooth decay among head start children.

PubMed

Heima, Masahiro; Ferretti, Margaret; Qureshi, Mehveen; Ferretti, Gerald

2017-10-01

Disparities among untreated dental caries exist for children from low-income families in the United States. Understanding of the mechanism of the disparities is required to reduce it and social geographic factors are one of the important influences. Although the effect of fluoridated water has been well reported, studies of other sociogeograpic factors, such as the density of available dentists, are still very limited. The objective of this study is to explore the effect of sociogeographic factors on the number of primary teeth with untreated dental caries among children from low-income families who are enrolled in Head Start programs throughout Northeast Ohio of the United States. This was a cross-sectional chart review study. Three hundred-eighty-eight charts were reviewed, and the number of primary teeth with untreated dental caries (dt) and the children's addresses were retrieved. The sociogeographic variables, including fluoridated water availability and the density of available dentists who accept a government-supported insurance (Medicaid dentists), were collected. The mean (standard deviation) of children's age was 3.51 (1.14) years with a range of 7 months to 5 years. A negative binomial regression model analysis, which used dt as a dependent variable and children's characteristic factors (i.e. age, gender, insurance type, and total number of primary teeth) and sociogeographic factors (i.e. Population, total number of Medicaid dentists, density of Medicaid dentist, and Fluoride water availability) of cities, as independent variables, demonstrated that only the density of Medicaid dentist in the sociogeographic factors indicated a significant effect (Estimated ß-Coefficients (Standard Errors)=-0.003 (0.002), p =0.030). This study demonstrated a significant negative association between the density of available dentists and untreated dental caries among children from low-income families in Head Start programs in Northeast Ohio. Increasing available dentists may be a strategy to reduce the number of early childhood caries. Key words: Child, poverty, dental caries, Health Services Accessibility.

Proton elastic scattering from stable and unstable nuclei - Extraction of nuclear densities

NASA Astrophysics Data System (ADS)

Sakaguchi, H.; Zenihiro, J.

2017-11-01

Progress in proton elastic scattering at intermediate energies to determine nuclear density distributions is reviewed. After challenges of about 15 years to explain proton elastic scattering and associated polarization phenomena at intermediate energies, we have reached to some conclusions regarding proton elastic scattering as a means of obtaining nuclear densities. During this same period, physics of unstable nuclei has become of interest, and the density distributions of protons and neutrons play more important roles in unstable nuclei, since the differences in proton and neutron numbers and densities are expected to be significant. As such, proton elastic scattering experiments at intermediate energies using the inverse kinematic method have started to determine density distributions of unstable nuclei. In the region of unstable nuclei, we are confronted with a new problem when attempting to find proton and neutron densities separately from elastic proton scattering data, since electron scattering data for unstable nuclei are not presently available. We introduce a new means of determining proton and neutron densities separately by double-energy proton elastic scattering at intermediate energies.

Using a 2D Model of the Io Plasma Torus to Investigate the Effects of Density Variations on the Morphology and Intensity of the Io Footprint

NASA Astrophysics Data System (ADS)

Payan, A. P.; Rajendar, A.; Paty, C. S.; Bonfond, B.; Crary, F.

2012-12-01

Io is the primary source of plasma in the Jovian magnetosphere, continuously releasing approximately 1 ton/s of SO2 from volcanic eruptions. The interaction of Io with Jupiter's magnetosphere is strongly influenced by the density structure of the resulting plasma torus and the position of Io relative to the center of the torus [Bonfond et al. 2008]. This unusual interaction produces a complex auroral feature on Jupiter's ionosphere known as the Io footprint. Hubble Space Telescope (HST) observations of Jupiter's far-UV aurora during spring 2007 showed an increased number of isolated auroral blobs along with a continuous expansion of Jupiter's main auroral oval over a few months. These blobs were associated with several large injections of hot plasma between 9 and 27 Jovian radii. These events coincided with a large volcanic eruption of the Tvashtar Paterae on Io, as observed by the New Horizons spacecraft [Spencer et al., 2007]. This, in turn, may have resulted in a significant increase in the plasma torus density. Besides, on June 7th, 2007, the Io footprint momentarily became so faint that it disappeared under a diffuse patch of emission remaining from an injection blob [Bonfond et al., 2012]. The goal of the present study is to examine the relationship between the increased density of the plasma torus and the dimming of the Io footprint. We implement a 2D model of the Io plasma torus that treats the variable-density torus as being composed of discrete layers of uniform density. As the co-rotating plasma in the plasma torus impinges on Io, Alfvén waves are launched at a pushback angle obtained from Gurnett and Goertz [1981]. The waves propagate inside the plasma torus through reflection and refraction at density discontinuities where they lose some of their initial energy. Using the above model, we can track the Alfvén wave fronts in the plasma torus and determine the longitude at which they exit the torus along with the corresponding remaining energy. Since Alfvén waves are capable of accelerating charged particles along magnetic field lines, we assume that the discrete Io footprint features are created at these longitudes, and that the intensity of each of these features is positively correlated to the energy transported by the wave front as it exits the plasma torus. Therefore, the model allows us to investigate both the effects of density changes and of Io's position in the plasma torus on the intensity and the morphology of the Io footprint. In this context, the model enables us to determine the density increase in the plasma torus required to explain the apparent disappearance of Io footprint given its position at that time.

A critical analysis of methods for rapid and nondestructive determination of wood density in standing trees

Treesearch

Shan Gao; Xiping Wang; Michael C. Wiemann; Brian K. Brashaw; Robert J. Ross; Lihai Wang

2017-01-01

Key message Field methods for rapid determination of wood density in trees have evolved from increment borer, torsiometer, Pilodyn, and nail withdrawal into sophisticated electronic tools of resistance drilling measurement. A partial resistance drilling approach coupled with knowledge of internal tree density distribution may...

Density conversion factor determined using a cone-beam computed tomography unit NewTom QR-DVT 9000.

PubMed

Lagravère, M O; Fang, Y; Carey, J; Toogood, R W; Packota, G V; Major, P W

2006-11-01

The purpose of this study was to determine a conversion coefficient for Hounsfield Units (HU) to material density (g cm(-3)) obtained from cone-beam computed tomography (CBCT-NewTom QR-DVT 9000) data. Six cylindrical models of materials with different densities were made and scanned using the NewTom QR-DVT 9000 Volume Scanner. The raw data were converted into DICOM format and analysed using Merge eFilm and AMIRA to determine the HU of different areas of the models. There was no significant difference (P = 0.846) between the HU given by each piece of software. A linear regression was performed using the density, rho (g cm(-3)), as the dependent variable in terms of the HU (H). The regression equation obtained was rho = 0.002H-0.381 with an R2 value of 0.986. The standard error of the estimation is 27.104 HU in the case of the Hounsfield Units and 0.064 g cm(-3) in the case of density. CBCT provides an effective option for determination of material density expressed as Hounsfield Units.

Ionospheric E-region electron density and neutral atmosphere variations

NASA Technical Reports Server (NTRS)

Stick, T. L.

1976-01-01

Electron density deviations from a basic variation with the solar zenith angle were investigated. A model study was conducted in which the effects of changes in neutral and relative densities of atomic and molecular oxygen on calculated electron densities were compared with incoherent scatter measurements in the height range 100-117 km at Arecibo, Puerto Rico. The feasibility of determining tides in the neutral atmosphere from electron density profiles was studied. It was determined that variations in phase between the density and temperature variation and the comparable magnitudes of their components make it appear improbable that the useful information on tidal modes can be obtained in this way.

A simple solution to systematic errors in density determination by X-ray reflectivity: The XRR-density evaluation (XRR-DE) method

NASA Astrophysics Data System (ADS)

Bergese, P.; Bontempi, E.; Depero, L. E.

2006-10-01

X-ray reflectivity (XRR) is a non-destructive, accurate and fast technique for evaluating film density. Indeed, sample-goniometer alignment is a critical experimental factor and the overriding error source in XRR density determination. With commercial single-wavelength X-ray reflectometers, alignment is difficult to control and strongly depends on the operator. In the present work, the contribution of misalignment on density evaluation error is discussed, and a novel procedure (named XRR-density evaluation or XRR-DE method) to minimize the problem will be presented. The method allows to overcome the alignment step through the extrapolation of the correct density value from appropriate non-specular XRR data sets. This procedure is operator independent and suitable for commercial single-wavelength X-ray reflectometers. To test the XRR-DE method, single crystals of TiO 2 and SrTiO 3 were used. In both cases the determined densities differed from the nominal ones less than 5.5%. Thus, the XRR-DE method can be successfully applied to evaluate the density of thin films for which only optical reflectivity is today used. The advantage is that this method can be considered thickness independent.

Ecological Determinants of Highly Pathogenic Avian Influenza (H5N1) Outbreaks in Bangladesh

PubMed Central

Ahmed, Syed S. U.; Ersbøll, Annette K.; Biswas, Paritosh K.; Christensen, Jens P.; Hannan, Abu S. M. A.; Toft, Nils

2012-01-01

Background The agro-ecology and poultry husbandry of the south Asian and south-east Asian countries share common features, however, with noticeable differences. Hence, the ecological determinants associated with risk of highly pathogenic avian influenza (HPAI-H5N1) outbreaks are expected to differ between Bangladesh and e.g., Thailand and Vietnam. The primary aim of the current study was to establish ecological determinants associated with the risk of HPAI-H5N1 outbreaks at subdistrict level in Bangladesh. The secondary aim was to explore the performance of two different statistical modeling approaches for unmeasured spatially correlated variation. Methodology/Principal Findings An ecological study at subdistrict level in Bangladesh was performed with 138 subdistricts with HPAI-H5N1 outbreaks during 2007–2008, and 326 subdistricts with no outbreaks. The association between ecological determinants and HPAI-H5N1 outbreaks was examined using a generalized linear mixed model. Spatial clustering of the ecological data was modeled using 1) an intrinsic conditional autoregressive (ICAR) model at subdistrict level considering their first order neighbors, and 2) a multilevel (ML) model with subdistricts nested within districts. Ecological determinants significantly associated with risk of HPAI-H5N1 outbreaks at subdistrict level were migratory birds' staging areas, river network, household density, literacy rate, poultry density, live bird markets, and highway network. Predictive risk maps were derived based on the resulting models. The resulting models indicate that the ML model absorbed some of the covariate effect of the ICAR model because of the neighbor structure implied in the two different models. Conclusions/Significance The study identified a new set of ecological determinants related to river networks, migratory birds' staging areas and literacy rate in addition to already known risk factors, and clarified that the generalized concept of free grazing duck and duck-rice cultivation interacted ecology are not significant determinants for Bangladesh. These findings will refine current understanding of the HPAI-H5N1 epidemiology in Bangladesh. PMID:22470496

Productivity, biodiversity, and pathogens influence the global hunter-gatherer population density.

PubMed

Tallavaara, Miikka; Eronen, Jussi T; Luoto, Miska

2018-02-06

The environmental drivers of species distributions and abundances are at the core of ecological research. However, the effects of these drivers on human abundance are not well-known. Here, we report how net primary productivity, biodiversity, and pathogen stress affect human population density using global ethnographic hunter-gatherer data. Our results show that productivity has significant effects on population density globally. The most important direct drivers, however, depend on environmental conditions: biodiversity influences population density exclusively in low-productivity regions, whereas pathogen stress does so in high-productivity regions. Our results also indicate that subtropical and temperate forest biomes provide the highest carrying capacity for hunter-gatherer populations. These findings document that environmental factors play a key role in shaping global population density patterns of preagricultural humans.

[Soil mesofauna in differents systems of land use soil in Upper River Solimões, AM, Brazil].

PubMed

Morais, José W De; Oliveira, Viviane Dos S; Dambros, Cristian De S; Tapia-Coral, Sandra C; Acioli, Agno N S

2010-01-01

The mesofauna has an important function in the soil and it is represented mainly by Acari Oribatida and Collembola. We report the first data on the density and diversity of the soil mesofauna in Benjamin Constant, Amazonas State, Brazil. The following systems were evaluated: primary forest, secondary forest, agroforestry system, cultivated areas and pastures. A total of 101 samples were collected 100 m apart from each other and specimens were collected by using Berlese-Tullgren method. The highest density was registered in secondary forest (29,776 specimens.m-2). Acari Oribatida was the dominant group (7.072 specimens.m-2) in the pasture, suggesting that mites show higher capacity of adaptation to disturbed environments and/or due to the presence of gregarious species. The density of Collembola (5,632 specimens.m-2) was higher in secondary forest. Formicidae was the dominant group (27,824 specimens.m-2) and its highest density occurred in the secondary forest (12,336 specimens.m-2). Seven species and ten morphospecies of Isoptera and three species of Symphyla were identified. The highest density and diversity were found in secondary forest. One supposes that the low density of mesofauna found in all of the studied systems is being influenced by soil structure and composition as well as litter volume. For SUT, the composition of taxonomic groups in the cultivated areas is similar to the one found in primary forest, while the groups found in the agroforestry system are similar to those in the pasture, which may help to decide on land use strategies.

Geodynamic stability of the primary in the binary asteroid system 65803 Didymos

NASA Astrophysics Data System (ADS)

Barnouin, Olivier S.; Maurel, Clara; Richardson, Derek C.; Ballouz, Ronald-Louis; Schwartz, Stephen; Michel, Patrick

2015-11-01

The moon of the near-Earth binary asteroid 65803 Didymos is the target of the Asteroid Impact and Deflection Assessment (AIDA) mission. This mission is a joint concept between NASA and ESA to investigate the effectiveness of a kinetic impactor in deflecting an asteroid. The mission is composed of two components: the NASA-led Double Asteroid Redirect Test (DART) that will impact the Didymos moon, and the ESA-led Asteroid Impact Monitoring (AIM) mission that will characterize the Didymos system. In order to provide AIDA constraints on the physical character of the both objects in this binary system, we undertook preliminary numerical investigations to evaluate the stability of the shape of the primary using its rapid 2.26 h rotation. We modeled the primary as a rubble pile. Each model consisted of thousands of uniform rigid spheres collapsed together under their own gravity to form a spherical pile that was then carved to match the current radar-derived shape model of the primary, as well as other comparable shapes (e.g. asteroid 1999 KW4, spheres) that were scaled to match best estimates of the size of Didymos. Each model was given a starting rotation period of 6 h with the spin axis aligned to the pole. At each timestep the spin rate was increased by a small amount so that after about 1 million timesteps the spin would match the observed rotation of 2.26 h. We tested a range of bulk densities spanning the current observational uncertainty (mean 2.4 g/cc) using "gravel"-like material parameters that provide significant resistance to sliding and rolling. We find that at the upper range of the density uncertainty it is possible for Didymos to hold its shape and not lose mass at its nominal rotation period, without the need for cohesive forces. At lower densities or with smoother particles, significant shape change occurs and mass loss is possible. We conclude that based on the radar shape available at the time of this writing, Didymos is marginally stable as a rubble pile with bulk density close to 3 g/cc. Revisions to the radar shape in process may allow for stability at lower bulk densities without cohesion. These results suggest that the moon of Didymos may also not be heavily influenced by cohesion.

Analysis of multi-layered films. [determining dye densities by applying a regression analysis to the spectral response of the composite transparency

NASA Technical Reports Server (NTRS)

Scarpace, F. L.; Voss, A. W.

1973-01-01

Dye densities of multi-layered films are determined by applying a regression analysis to the spectral response of the composite transparency. The amount of dye in each layer is determined by fitting the sum of the individual dye layer densities to the measured dye densities. From this, dye content constants are calculated. Methods of calculating equivalent exposures are discussed. Equivalent exposures are a constant amount of energy over a limited band-width that will give the same dye content constants as the real incident energy. Methods of using these equivalent exposures for analysis of photographic data are presented.

Comparison of precision orbit derived density estimates for CHAMP and GRACE satellites

NASA Astrophysics Data System (ADS)

Fattig, Eric Dale

Current atmospheric density models cannot adequately represent the density variations observed by satellites in Low Earth Orbit (LEO). Using an optimal orbit determination process, precision orbit ephemerides (POE) are used as measurement data to generate corrections to density values obtained from existing atmospheric models. Densities obtained using these corrections are then compared to density data derived from the onboard accelerometers of satellites, specifically the CHAMP and GRACE satellites. This comparison takes two forms, cross correlation analysis and root mean square analysis. The densities obtained from the POE method are nearly always superior to the empirical models, both in matching the trends observed by the accelerometer (cross correlation), and the magnitudes of the accelerometer derived density (root mean square). In addition, this method consistently produces better results than those achieved by the High Accuracy Satellite Drag Model (HASDM). For satellites orbiting Earth that pass through Earth's upper atmosphere, drag is the primary source of uncertainty in orbit determination and prediction. Variations in density, which are often not modeled or are inaccurately modeled, cause difficulty in properly calculating the drag acting on a satellite. These density variations are the result of many factors; however, the Sun is the main driver in upper atmospheric density changes. The Sun influences the densities in Earth's atmosphere through solar heating of the atmosphere, as well as through geomagnetic heating resulting from the solar wind. Data are examined for fourteen hour time spans between November 2004 and July 2009 for both the CHAMP and GRACE satellites. This data spans all available levels of solar and geomagnetic activity, which does not include data in the elevated and high solar activity bins due to the nature of the solar cycle. Density solutions are generated from corrections to five different baseline atmospheric models, as well as nine combinations of density and ballistic coefficient correlated half-lives. These half-lives are varied among values of 1.8, 18, and 180 minutes. A total of forty-five sets of results emerge from the orbit determination process for all combinations of baseline density model and half-lives. Each time period is examined for both CHAMP and GRACE-A, and the results are analyzed. Results are averaged from all solutions periods for 2004--2007. In addition, results are averaged after binning according to solar and geomagnetic activity levels. For any given day in this period, a ballistic coefficient correlated half-life of 1.8 minutes yields the best correlation and root mean square values for both CHAMP and GRACE. For CHAMP, a density correlated half-life of 18 minutes is best for higher levels of solar and geomagnetic activity, while for lower levels 180 minutes is usually superior. For GRACE, 180 minutes is nearly always best. The three Jacchia-based atmospheric models yield very similar results. The CIRA 1972 or Jacchia 1971 models as baseline consistently produce the best results for both satellites, though results obtained for Jacchia-Roberts are very similar to the other Jacchia-based models. Data are examined in a similar manner for the extended solar minimum period during 2008 and 2009, albeit with a much smaller sampling of data. With the exception of some atypical results, similar combinations of half-lives and baseline atmospheric model produce the best results. A greater sampling of data will aid in characterizing density in a period of especially low solar activity. In general, cross correlation values for CHAMP and GRACE revealed that the POE method matched trends observed by the accelerometers very well. However, one period of time deviated from this trend for the GRACE-A satellite. Between late October 2005 and January 2006, correlations for GRACE-A were very low. Special examination of the surrounding months revealed the extent of time this period covered. Half-life and baseline model combinations that produced the best results during this time were similar to those during normal periods. Plotting these periods revealed very short period density variations in the accelerometer that could not be reproduced by the empirical models, HASDM, or the POE method. Finally, densities produced using precision orbit data for the GRACE-B satellite were shown to be nearly indistinguishable from those produced by GRACE-A. Plots of the densities produced for both satellites during the same time periods revealed this fact. Multiple days were examined covering all possible ranges of solar and geomagnetic activity. In addition, the period in which GRACE-A correlations were low was studied. No significant differences existed between GRACE-A and GRACE-B for all of the days examined.

39 CFR 254.2 - Definition of primary function area and criteria used to determine whether an alteration has an...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Definition of primary function area and criteria used to determine whether an alteration has an effect on an area containing a primary function that is... ARCHITECTURAL BARRIERS ACT § 254.2 Definition of primary function area and criteria used to determine whether an...

39 CFR 254.2 - Definition of primary function area and criteria used to determine whether an alteration has an...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 39 Postal Service 1 2011-07-01 2011-07-01 false Definition of primary function area and criteria used to determine whether an alteration has an effect on an area containing a primary function that is... ARCHITECTURAL BARRIERS ACT § 254.2 Definition of primary function area and criteria used to determine whether an...

39 CFR 254.2 - Definition of primary function area and criteria used to determine whether an alteration has an...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 39 Postal Service 1 2014-07-01 2014-07-01 false Definition of primary function area and criteria used to determine whether an alteration has an effect on an area containing a primary function that is... ARCHITECTURAL BARRIERS ACT § 254.2 Definition of primary function area and criteria used to determine whether an...

39 CFR 254.2 - Definition of primary function area and criteria used to determine whether an alteration has an...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 39 Postal Service 1 2012-07-01 2012-07-01 false Definition of primary function area and criteria used to determine whether an alteration has an effect on an area containing a primary function that is... ARCHITECTURAL BARRIERS ACT § 254.2 Definition of primary function area and criteria used to determine whether an...

39 CFR 254.2 - Definition of primary function area and criteria used to determine whether an alteration has an...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 39 Postal Service 1 2013-07-01 2013-07-01 false Definition of primary function area and criteria used to determine whether an alteration has an effect on an area containing a primary function that is... ARCHITECTURAL BARRIERS ACT § 254.2 Definition of primary function area and criteria used to determine whether an...

Inverse problems for torsional modes.

USGS Publications Warehouse

Willis, C.

1984-01-01

Considers a spherically symmetric, non-rotating Earth consisting of an isotropic, perfect elastic material where the density and the S-wave velocity may have one or two discontinuities in the upper mantle. Shows that given the velocity throughout the mantle and the crust and given the density in the lower mantle, then the freqencies of the torsional oscillations of one angular order (one torsional spectrum), determine the density in the upper mantle and in the crust uniquely. If the velocity is known only in the lower mantle, then the frequencies of the torsional oscillations of two angular orders uniquely determine both the density and the velocity in the upper mantle and in the crust. In particular, the position and size of the discontinuities in the density and velocity are uniquely determined by two torsional spectra.-Author

Fluid flow in solidifying monotectic alloys

NASA Technical Reports Server (NTRS)

Ecker, A.; Frazier, D. O.; Alexander, J. Iwan D.

1989-01-01

Use of a two-wavelength holographic technique results in a simultaneous determination of temperature and composition profiles during directional solidification in a system with a miscibility gap. The relationships among fluid flow, phase separation, and mass transport during the solidification of the monotectic alloy are discussed. The primary sources of fluid motion in this system are buoyancy and thermocapillary forces. These forces act together when phase separation results in the formation of droplets (this occurs at the solid-liquid interface and in the bulk melt). In the absence of phase separation, buoyancy results from density gradients related to temperature and compositional gradients in the single-phase bulk melt. The effects of buoyancy are especially evident in association with water- or ethanol-rich volumes created at the solid-liquid growth interface.

A comparison of experimental and computer model results on the charge-exchange plasma flow from a 30 cm mercury ion thruster

NASA Technical Reports Server (NTRS)

Gabriel, S. B.; Kaufman, H. R.

1982-01-01

Ion thrusters can be used in a variety of primary and auxiliary space-propulsion applications. A thruster produces a charge-exchange plasma which can interact with various systems on the spacecraft. The propagation of the charge-exchange plasma is crucial in determining the interaction of that plasma with the spacecraft. This paper compares experimental measurements with computer model predictions of the propagation of the charge-exchange plasma from a 30 cm mercury ion thruster. The plasma potentials, and ion densities, and directed energies are discussed. Good agreement is found in a region upstream of, and close to, the ion thruster optics. Outside of this region the agreement is reasonable in view of the modeling difficulties.

Preparation of a primary argon beam for the CERN fixed target physics.

PubMed

Küchler, D; O'Neil, M; Scrivens, R; Thomae, R

2014-02-01

The fixed target experiment NA61 in the North Area of the Super Proton Synchrotron is studying phase transitions in strongly interacting matter. Up to now they used the primary beams available from the CERN accelerator complex (protons and lead ions) or fragmented beams created from the primary lead ion beam. To explore a wider range of energies and densities a request was made to provide primary argon and xenon beams. This paper describes the results of the setting up and 10 week test run of the Ar(11+) beam from the 14.5 GHz ECR ion source and the linear accelerator (Linac3) at CERN.

Determination of Charge-Carrier Mobility in Disordered Thin-Film Solar Cells as a Function of Current Density

NASA Astrophysics Data System (ADS)

Mäckel, Helmut; MacKenzie, Roderick C. I.

2018-03-01

Charge-carrier mobility is a fundamental material parameter, which plays an important role in determining solar-cell efficiency. The higher the mobility, the less time a charge carrier will spend in a device and the less likely it is that it will be lost to recombination. Despite the importance of this physical property, it is notoriously difficult to measure accurately in disordered thin-film solar cells under operating conditions. We, therefore, investigate a method previously proposed in the literature for the determination of mobility as a function of current density. The method is based on a simple analytical model that relates the mobility to carrier density and transport resistance. By revising the theoretical background of the method, we clearly demonstrate what type of mobility can be extracted (constant mobility or effective mobility of electrons and holes). We generalize the method to any combination of measurements that is able to determine the mean electron and hole carrier density, and the transport resistance at a given current density. We explore the robustness of the method by simulating typical organic solar-cell structures with a variety of physical properties, including unbalanced mobilities, unbalanced carrier densities, and for high or low carrier trapping rates. The simulations reveal that near VOC and JSC , the method fails due to the limitation of determining the transport resistance. However, away from these regions (and, importantly, around the maximum power point), the method can accurately determine charge-carrier mobility. In the presence of strong carrier trapping, the method overestimates the effective mobility due to an underestimation of the carrier density.

Effect of object location on the density measurement and Hounsfield conversion in a NewTom 3G cone beam computed tomography unit.

PubMed

Lagravère, M O; Carey, J; Ben-Zvi, M; Packota, G V; Major, P W

2008-09-01

The purpose of this study was to determine the effect of an object's location in a cone beam CT imaging chamber (CBCT-NewTom 3G) on its apparent density and to develop a linear conversion coefficient for Hounsfield units (HU) to material density (g cm(-3)) for the NewTom 3G Scanner. Three cylindrical models of materials with different densities were constructed and scanned at five different locations in a NewTom 3G Volume Scanner. The average HU value for each model at each location was obtained using two different types of software. Next, five cylinders of different known densities were scanned at the exact centre of a NewTom 3G Scanner. The collected data were analysed using the same two types of software to determine a standard linear relationship between density and HU for each type of software. There is no statistical significance of location of an object within the CBCT scanner on determination of its density. A linear relationship between the density of an object and the HU of a scan was rho = 0.001(HU)+1.19 with an R2 value of 0.893 (where density, rho, is measured in g cm(-3)). This equation is to be used on a range between 1.42 g cm(-3) and 0.4456 g cm(-3). A linear relationship can be used to determine the density of materials (in the density range of bone) from the HU values of a CBCT scan. This relationship is not affected by the object's location within the scanner itself.

New Formulation for the Viscosity of n-Butane

NASA Astrophysics Data System (ADS)

Herrmann, Sebastian; Vogel, Eckhard

2018-03-01

A new viscosity formulation for n-butane, based on the residual quantity concept, uses the reference equation of state by Bücker and Wagner [J. Phys. Chem. Ref. Data 35, 929 (2006)] and is valid in the fluid region from the triple point to 650 K and to 100 MPa. The contributions for the zero-density viscosity and for the initial-density dependence were separately developed, whereas those for the critical enhancement and for the higher-density terms were pretreated. All contributions were given as a function of the reciprocal reduced temperature τ, while the last two contributions were correlated as a function of τ and of the reduced density δ. The different contributions were based on specific primary data sets, whose evaluation and choice were discussed in detail. The final formulation incorporates 13 coefficients derived employing a state-of-the-art linear optimization algorithm. The viscosity at low pressures p ≤ 0.2 MPa is described with an expanded uncertainty of 0.5% (coverage factor k = 2) for temperatures 293 ≤ T/K ≤ 626. The expanded uncertainty in the vapor phase at subcritical temperatures T ≥ 298 K as well as in the supercritical thermodynamic region T ≤ 448 K at pressures p ≤ 30 MPa is estimated to be 1.5%. It is raised to 4.0% in regions where only less reliable primary data sets are available and to 6.0% in ranges without any primary data, but in which the equation of state is valid. A weakness of the reference equation of state in the near-critical region prevents estimation of the expanded uncertainty in this region. Viscosity tables for the new formulation are presented in Appendix B for the single-phase region, for the vapor-liquid phase boundary, and for the near-critical region.

New Formulation for the Viscosity of Propane

NASA Astrophysics Data System (ADS)

Vogel, Eckhard; Herrmann, Sebastian

2016-12-01

A new viscosity formulation for propane, using the reference equation of state for its thermodynamic properties by Lemmon et al. [J. Chem. Eng. Data 54, 3141 (2009)] and valid in the fluid region from the triple-point temperature to 650 K and pressures up to 100 MPa, is presented. At the beginning, a zero-density contribution and one for the critical enhancement, each based on the experimental data, were independently generated in parts. The higher-density contributions are correlated as a function of the reciprocal reduced temperature τ = Tc/T and of the reduced density δ = ρ/ρc (Tc—critical temperature, ρc—critical density). The final formulation includes 17 coefficients inferred by applying a state-of-the-art linear optimization algorithm. The evaluation and choice of the primary data sets are detailed due to its importance. The viscosity at low pressures p ≤ 0.2 MPa is represented with an expanded uncertainty of 0.5% (coverage factor k = 2) for temperatures 273 ≤ T/K ≤ 625. The expanded uncertainty in the vapor phase at subcritical temperatures T ≥ 273 K as well as in the supercritical thermodynamic region T ≤ 423 K at pressures p ≤ 30 MPa is assumed to be 1.5%. In the near-critical region (1.001 < 1/τ < 1.010 and 0.8 < δ < 1.2), the expanded uncertainty increases with decreasing temperature up to 3.0%. It is further increased to 4.0% in regions of less reliable primary data sets and to 6.0% in ranges in which no primary data are available but the equation of state is valid. Tables of viscosity computed for the new formulation are given in an Appendix for the single-phase region, for the vapor-liquid phase boundary, and for the near-critical region.

The Neocortex of Indian River Dolphins (Genus Platanista): Comparative, Qualitative and Quantitative Analysis.

PubMed

Knopf, Julian P; Hof, Patrick R; Oelschläger, Helmut H A

2016-01-01

We investigated the morphology of four primary neocortical projection areas (somatomotor, somatosensory, auditory, visual) qualitatively and quantitatively in the Indian river dolphins (Platanista gangetica gangetica, P. gangetica minor) with histological and stereological methods. For comparison, we included brains of other toothed whale species. Design-based stereology was applied to the primary neocortical areas (M1, S1, A1, V1) of the Indian river dolphins and compared to those of the bottlenose dolphin with respect to layers III and V. These neocortical fields were identified using existing electrophysiological and morphological data from marine dolphins as to their topography and histological structure, including the characteristics of the neuron populations concerned. In contrast to other toothed whales, the visual area (V1) of the 'blind' river dolphins seems to be rather small. M1 is displaced laterally and the auditory area (A1) is larger than in marine species with respect to total brain size. The layering is similar in the cortices of all the toothed whale brains investigated; a layer IV could not be identified. Cell density in layer III is always higher than in layer V. The maximal neuron density in P. gangetica gangetica is found in layer III of A1, followed by layers III in V1, S1, and M1. The cell density in layer V is at a similar level in all primary areas. There are, however, some differences in neuron density between the two subspecies of Indian river dolphins. Taken as a whole, it appears that the neocortex of platanistids exhibits a considerable expansion of the auditory field. Even more than other toothed whales, they seem to depend on their biosonar abilities for navigation, hunting, and communication in their riverine habitat. © 2016 S. Karger AG, Basel.

Clinical Evaluation of a Loop-Mediated Amplification Kit for Diagnosis of Imported Malaria

PubMed Central

Polley, Spencer D.; González, Iveth J.; Mohamed, Deqa; Daly, Rosemarie; Bowers, Kathy; Watson, Julie; Mewse, Emma; Armstrong, Margaret; Gray, Christen; Perkins, Mark D.; Bell, David; Kanda, Hidetoshi; Tomita, Norihiro; Kubota, Yutaka; Mori, Yasuyoshi; Chiodini, Peter L.; Sutherland, Colin J.

2013-01-01

Background. Diagnosis of malaria relies on parasite detection by microscopy or antigen detection; both fail to detect low-density infections. New tests providing rapid, sensitive diagnosis with minimal need for training would enhance both malaria diagnosis and malaria control activities. We determined the diagnostic accuracy of a new loop-mediated amplification (LAMP) kit in febrile returned travelers. Methods. The kit was evaluated in sequential blood samples from returned travelers sent for pathogen testing to a specialist parasitology laboratory. Microscopy was performed, and then malaria LAMP was performed using Plasmodium genus and Plasmodium falciparum–specific tests in parallel. Nested polymerase chain reaction (PCR) was performed on all samples as the reference standard. Primary outcome measures for diagnostic accuracy were sensitivity and specificity of LAMP results, compared with those of nested PCR. Results. A total of 705 samples were tested in the primary analysis. Sensitivity and specificity were 98.4% and 98.1%, respectively, for the LAMP P. falciparum primers and 97.0% and 99.2%, respectively, for the Plasmodium genus primers. Post hoc repeat PCR analysis of all 15 tests with discrepant results resolved 4 results in favor of LAMP, suggesting that the primary analysis had underestimated diagnostic accuracy. Conclusions. Malaria LAMP had a diagnostic accuracy similar to that of nested PCR, with a greatly reduced time to result, and was superior to expert microscopy. PMID:23633403

Phase relationships of the system Fe-Ni-S and structure of the high-pressure phase of (Fe1-xNix)3S2

NASA Astrophysics Data System (ADS)

Urakawa, Satoru; Kamuro, Ryota; Suzuki, Akio; Kikegawa, Takumi

2018-04-01

The phase relationships of the Fe-Ni-S system at 15 GPa were studied by high pressure quench experiments. The stability fields of (Fe,Ni)3S and (Fe,Ni)3S2 and the melting relationships of the Fe-Ni-S system were determined as a function of Ni content. The (Fe,Ni)3S solid solution is stable in the composition of Ni/(Fe + Ni) > 0.7 and melts incongruently into an Fe-Ni alloy + liquid. The (Fe,Ni)3S2 makes a complete solid solution and melts incongruently into (Fe,Ni)S + liquid, whose structure was determined to show Cmcm-orthorhombic symmetry by in situ synchrotron X-ray diffraction experiments. The eutectic contains about 30 at.% of S, and its temperature decreases with increasing Ni content with a rate of ∼5 K/at.% from 1175 K. The density of the Fe-FeS eutectic composition (Fe70S30) liquid is evaluated to be 6.93 ± 0.08 g/cm3 at 15 GPa and 1200 K based on the Clausius-Clapeyron relations and densities of subsolidus phases. The Fe-Ni-S liquids are a primary sulfur-bearing phase in the deep mantle with a reducing condition (250-660 km depth), and they would play a significant role in the carbon cycle as a carbon host as well as in the generation of diamond.

Lightning characteristics of derecho producing mesoscale convective systems

NASA Astrophysics Data System (ADS)

Bentley, Mace L.; Franks, John R.; Suranovic, Katelyn R.; Barbachem, Brent; Cannon, Declan; Cooper, Stonie R.

2016-06-01

Derechos, or widespread, convectively induced wind storms, are a common warm season phenomenon in the Central and Eastern United States. These damaging and severe weather events are known to sweep quickly across large spatial regions of more than 400 km and produce wind speeds exceeding 121 km h-1. Although extensive research concerning derechos and their parent mesoscale convective systems already exists, there have been few investigations of the spatial and temporal distribution of associated cloud-to-ground lightning with these events. This study analyzes twenty warm season (May through August) derecho events between 2003 and 2013 in an effort to discern their lightning characteristics. Data used in the study included cloud-to-ground flash data derived from the National Lightning Detection Network, WSR-88D imagery from the University Corporation for Atmospheric Research, and damaging wind report data obtained from the Storm Prediction Center. A spatial and temporal analysis was conducted by incorporating these data into a geographic information system to determine the distribution and lightning characteristics of the environments of derecho producing mesoscale convective systems. Primary foci of this research include: (1) finding the approximate size of the lightning activity region for individual and combined event(s); (2) determining the intensity of each event by examining the density and polarity of lightning flashes; (3) locating areas of highest lightning flash density; and (4) to provide a lightning spatial analysis that outlines the temporal and spatial distribution of flash activity for particularly strong derecho producing thunderstorm episodes.

Scale-dependent mechanisms of habitat selection for a migratory passerine: an experimental approach

USGS Publications Warehouse

Donovan, Therese M.; Cornell, Kerri L.

2010-01-01

Habitat selection theory predicts that individuals choose breeding habitats that maximize fitness returns on the basis of indirect environmental cues at multiple spatial scales. We performed a 3-year field experiment to evaluate five alternative hypotheses regarding whether individuals choose breeding territories in heterogeneous landscapes on the basis of (1) shrub cover within a site, (2) forest land-cover pattern surrounding a site, (3) conspecific song cues during prebreeding settlement periods, (4) a combination of these factors, and (5) interactions among these factors. We tested hypotheses with playbacks of conspecific song across a gradient of landscape pattern and shrub density and evaluated changes in territory occupancy patterns in a forest-nesting passerine, the Black-throated Blue Warbler (Dendroica caerulescens). Our results support the hypothesis that vegetation structure plays a primary role during presettlement periods in determining occupancy patterns in this species. Further, both occupancy rates and territory turnover were affected by an interaction between local shrub density and amount of forest in the surrounding landscape, but not by interactions between habitat cues and social cues. Although previous studies of this species in unfragmented landscapes found that social postbreeding song cues played a key role in determining territory settlement, our prebreeding playbacks were not associated with territory occupancy or turnover. Our results suggest that in heterogeneous landscapes during spring settlement, vegetation structure may be a more reliable signal of reproductive performance than the physical location of other individuals.

VLF Transmitter Signal Power Loss to Quasi-Electrostatic Whistler Mode Waves in Regions Containing Plasma Density Irregularities

NASA Astrophysics Data System (ADS)

Bell, T. F.; Foust, F.; Inan, U. S.; Lehtinen, N. G.

2010-12-01

The energetic particles comprising the Earth’s radiation belts are an important component of Space Weather. The commonly accepted model of the quasi-steady radiation belts developed by Abel and Thorne [1998] proposes that VLF signals from powerful ground based transmitters determine the lifetimes of energetic radiation belt electrons (100 keV-1.5 MeV) on L shells in the range 1.3-2.8. The primary mechanism of interaction is pitch angle scattering during gyro-resonance. Recent observations [Starks et al., 2008] from multiple spacecraft suggest that the actual night time intensity of VLF transmitter signals in the radiation belts is approximately 20 dB below the level assumed in the Abel and Thorne model and approximately 10 dB below model values during the day. In this work we discuss one mechanism which might be responsible for a large portion of this intensity discrepancy. The mechanism is linear mode coupling between electromagnetic whistler mode waves and quasi-electrostatic whistler mode waves. As VLF electromagnetic whistler mode waves propagate through regions containing small scale (2-100 m) magnetic-field-aligned plasma density irregularities, they excite quasi-electrostatic whistler mode waves, and this excitation represents a power loss for the input waves. We construct plausible models of the irregularities in order to use numerical simulations to determine the characteristics of the mode coupling mechanism and the conditions under which the input VLF waves can lose significant power to the excited quasi-electrostatic whistler mode waves.

Food-Web Structure in Relation to Environmental Gradients and Predator-Prey Ratios in Tank-Bromeliad Ecosystems

PubMed Central

Dézerald, Olivier; Leroy, Céline; Corbara, Bruno; Carrias, Jean-François; Pélozuelo, Laurent; Dejean, Alain; Céréghino, Régis

2013-01-01

Little is known of how linkage patterns between species change along environmental gradients. The small, spatially discrete food webs inhabiting tank-bromeliads provide an excellent opportunity to analyse patterns of community diversity and food-web topology (connectance, linkage density, nestedness) in relation to key environmental variables (habitat size, detrital resource, incident radiation) and predators:prey ratios. We sampled 365 bromeliads in a wide range of understorey environments in French Guiana and used gut contents of invertebrates to draw the corresponding 365 connectance webs. At the bromeliad scale, habitat size (water volume) determined the number of species that constitute food-web nodes, the proportion of predators, and food-web topology. The number of species as well as the proportion of predators within bromeliads declined from open to forested habitats, where the volume of water collected by bromeliads was generally lower because of rainfall interception by the canopy. A core group of microorganisms and generalist detritivores remained relatively constant across environments. This suggests that (i) a highly-connected core ensures food-web stability and key ecosystem functions across environments, and (ii) larger deviations in food-web structures can be expected following disturbance if detritivores share traits that determine responses to environmental changes. While linkage density and nestedness were lower in bromeliads in the forest than in open areas, experiments are needed to confirm a trend for lower food-web stability in the understorey of primary forests. PMID:23977128

Importance of Doppler broadening in Compton scatter imaging techniques

NASA Astrophysics Data System (ADS)

Rao, Donepudi V.; Takeda, Tohoru; Itai, Yuji; Seltzer, S. M.; Hubbell, John H.; Zeniya, Tsutomu; Akatsuka, Takao; Cesareo, Roberto; Brunetti, Antonio; Gigante, Giovanni E.

2001-12-01

Compton scattering is a potential tool for the determination of bone mineral content or tissue density for dose planning purposes, and requires knowledge of the energy distribution of the X-rays through biological materials of medical interest in the X-ray and (gamma) -ray region. The energy distribution is utilized in a number of ways in diagnostic radiology, for example, in determining primary photon spectra, electron densities in separate volumes, and in tomography and imaging. The choice of the X-ray energy is more related to X-ray absorption, where as that of the scattering angle is more related to geometry. The evaluation of all the contributions are mandatory in Compton profile measurements and is important in X-ray imaging systems in order to achieve good results. In view of this, Compton profile cross-sections for few biological materials are estimated at nineteen K(alpha) X-ray energies and 60 keV (Am-241) photons. Energy broadening, geometrical broadening from 1 to 180 degree(s), FWHM of J(Pz) and FWHM of Compton energy broadening has been evaluated at various incident photon energies. These values are estimated around the centroid of the Compton profile with an energy interval of 0.1 keV and 1.0 keV for 60 keV photons. The interaction cross sections for the above materials are estimated using fractions-by-weight of the constituent elements. Input data for these tables are purely theoretical.

Process strengths determine the forms of the relationship between plant species richness and primary productivity

PubMed Central

Wang, Zhenhong

2017-01-01

The current rates of biodiversity loss have exceeded the rates observed during the earth’s major extinction events, which spurs the studies of the ecological relationships between biodiversity and ecosystem functions, stability, and services to determine the consequences of biodiversity loss. Plant species richness-productivity relationship (SRPR) is crucial to the understanding of these relationships in plants. Most ecologists have reached a widespread consensus that the loss of plant diversity undoubtedly impairs ecosystem functions, and have proposed many processes to explain the SRPR. However, none of the available studies has satisfactorily described the forms and mechanisms clarifying the SRPR. Observed results of the SRPR forms are inconsistent, and studies have long debated the ecological processes explaining the SRPR. Here, I have developed a simple model that combines the positive and/or negative effects of sixteen ecological processes on the SRPR and models that describe the dynamics of complementary-selection effect, density effect, and the interspecific competitive stress influenced by other ecological processes. I can regulate the strengths of the effects of these ecological processes to derive the asymptotic, positive, humped, negative, and irregular forms of the SRPR, and verify these forms using the observed data. The results demonstrated that the different strengths of the ecological processes determine the forms of the SRPR. The forms of the SRPR can change with variations in the strengths of the ecological processes. The dynamic characteristics of the complementary-selection effect, density effect, and the interspecific competitive stress on the SRPR are diverse, and are dependent on the strengths and variation of the ecological processes. This report explains the diverse forms of the SRPR, clarifies the integrative effects of the different ecological processes on the SRPR, and deepens our understanding of the interactions that occur among these ecological processes. PMID:29140995

2016 Canadian Cardiovascular Society Guidelines for the Management of Dyslipidemia for the Prevention of Cardiovascular Disease in the Adult.

PubMed

Anderson, Todd J; Grégoire, Jean; Pearson, Glen J; Barry, Arden R; Couture, Patrick; Dawes, Martin; Francis, Gordon A; Genest, Jacques; Grover, Steven; Gupta, Milan; Hegele, Robert A; Lau, David C; Leiter, Lawrence A; Lonn, Eva; Mancini, G B John; McPherson, Ruth; Ngui, Daniel; Poirier, Paul; Sievenpiper, John L; Stone, James A; Thanassoulis, George; Ward, Richard

2016-11-01

Since the publication of the 2012 guidelines new literature has emerged to inform decision-making. The 2016 guidelines primary panel selected a number of clinically relevant questions and has produced updated recommendations, on the basis of important new findings. In subjects with clinical atherosclerosis, abdominal aortic aneurysm, most subjects with diabetes or chronic kidney disease, and those with low-density lipoprotein cholesterol ≥ 5 mmol/L, statin therapy is recommended. For all others, there is an emphasis on risk assessment linked to lipid determination to optimize decision-making. We have recommended nonfasting lipid determination as a suitable alternative to fasting levels. Risk assessment and lipid determination should be considered in individuals older than 40 years of age or in those at increased risk regardless of age. Pharmacotherapy is generally not indicated for those at low Framingham Risk Score (FRS; <10%). A wider range of patients are now eligible for statin therapy in the FRS intermediate risk category (10%-19%) and in those with a high FRS (> 20%). Despite the controversy, we continue to advocate for low-density lipoprotein cholesterol targets for subjects who start therapy. Detailed recommendations are also presented for health behaviour modification that is indicated in all subjects. Finally, recommendation for the use of nonstatin medications is provided. Shared decision-making is vital because there are many areas in which clinical trials do not fully inform practice. The guidelines are meant to be a platform for meaningful conversation between patient and care provider so that individual decisions can be made for risk screening, assessment, and treatment. Copyright © 2016 Canadian Cardiovascular Society. Published by Elsevier Inc. All rights reserved.

Correlation of design with performance of primary lithium-sulfur oxyhalide cells

NASA Technical Reports Server (NTRS)

Frank, H. A.

1982-01-01

Results and assessments of a focused literature review of primary lithium sulfur oxyhalide cells are presented. Major emphasis is placed on the effect of component materials and designs on performance (energy density and rate capability), safety, and storage life of these cells. This information is a reference guide for the design of high energy batteries for future use on NASA missions.