Bonding of composite resins to PEEK: the influence of adhesive systems and air-abrasion parameters.

PubMed

Stawarczyk, Bogna; Taufall, Simon; Roos, Malgorzata; Schmidlin, Patrick R; Lümkemann, Nina

2018-03-01

The objective of the study was to investigate the tensile bond strength (TBS) to polyaryletheretherketone (PEEK) after different pretreatment and conditioning methods. Four hundred PEEK specimens were fabricated and allocated to the following air-abrasion methods (n 1  = 80/pretreatment): (i) 50 μm Al 2 O 3 (0.05 MPa); (ii) 50 μm Al 2 O 3 (0.35 MPa); (iii) 110 μm Al 2 O 3 (0.05 MPa); (iv) 110 μm Al 2 O 3 (0.35 MPa); and (v) Rocatec 110 μm (0.28 MPa). These pretreatments were combined with the following conditioning methods (n 2  = 20/pretreatment/conditioning): (a) visio.link (VL); (b) Monobond Plus/Heliobond (MH); (c) Scotchbond Universal (SU); and (d) dialog bonding fluid (DB). After veneering of all specimens with dialog occlusal and aging (28 days H 2 O, 37 °C + 20,000 thermal cycles, 5/55 °C), TBS was measured. Data was analysed using Kaplan-Meier survival analysis with Breslow-Gehan test and Cox-regressions. The major impact on TBS showed the conditioning, followed by the air-abrasion-pressure, while the grain size of the air-abrasion powder did not show any effect. Specimens air-abraded at 0.35 MPa showed the highest survival rates. However, within VL groups, this observation was not statistically significant. Within MH groups, pretreatment using 110 μm Al 2 O 3 and 0.05 MPa resulted in higher survival rates compared to groups treated with 50 and 110 μm Al 2 O 3 using a pressure of 0.35 MPa. The use of VL showed the highest survival rates between the adhesive systems and the TBS values higher than 25 MPa independent of the pretreatment method. As an exception, only VL showed significantly higher survival rates when compared to MH. The adequate choice of the adhesive system and higher pressures improved the TBS between PEEK and veneering resin composite. The particle size had no major impact. According to this study, best veneering of PEEK with dialog occlusal can be achieved by conditioning with visio.link in combination with

Silica coating on alumina ceramic: comparison of three chairside air-abrasion devices working for different times and distances.

PubMed

Pestana Passos, S; Dias Vanderlei, A; Ozcan, M; Felipe Valandro, L F; Felipe Valandro, L

2011-03-01

This study evaluated, by scanning electron microscope (SEM) and EDS, the effect of different strategies for silica coating (sandblasters, time and distance) of a glass-infiltrated ceramic (In-Ceram Alumina). Forty-one ceramic blocks were produced. For comparison of the three air-abrasion devices, 15 ceramic samples were divided in three groups (N.=5): Bioart, Microetcher and Ronvig (air-abrasion parameters: 20 s at a distance of 10 mm). For evaluation of the time and distance factors, ceramic samples (N.=5) were allocated in groups considering three applied times (5 s, 13 s and 20 s) and two distances (10 mm and 20 mm), using the Ronvig device. In a control sample, no surface treatment was performed. After that, the micro-morphologic analyzes of the ceramic surfaces were made using SEM. EDS analyzes were carried out to detect the % of silica on representative ceramic surface. ANOVA and Tukey tests were used to analyze the results. One-way ANOVA showed the silica deposition was different for different devices (P=0.0054). The Ronvig device promoted the highest silica coating compared to the other devices (Tukey test). Two-way ANOVA showed the distance and time factors did not affect significantly the silica deposition (application time and distance showed no statistical difference). The Ronvig device provided the most effective silica deposition on glass-infiltrated alumina ceramic surface and the studied time and distance for air-abrasion did not affect the silica coating.

Impact of dentifrice abrasivity and remineralization time on erosive tooth wear in vitro.

PubMed

Buedel, Sarah; Lippert, Frank; Zero, Domenick T; Eckert, George J; Hara, Anderson T

2018-02-01

To investigate the in vitro effects of simulated dentifrice slurry abrasivity (L-low, M-medium and H-high) and remineralization time (0, 30, 60 and 120 minutes) on erosive tooth wear. Enamel and root dentin specimens were prepared from bovine incisors (n= 8) and submitted to a cycling protocol including erosion, remineralization at the test times, and brushing with each of the tested slurries, for 5 days. Dental surface loss (SL) was determined by optical profilometry. Data was analyzed using mixed-model ANOVA and Fisher's PLSD tests (alpha= 0.05). SL generally increased along with the increase in slurry abrasive level, with significance dependent upon the specific substrate and remineralization times. H showed the highest SL on both enamel and dentin; remineralization for 30 minutes reduced SL significantly (P< 0.05), but only for enamel. M showed intermediate SL values, with remineralization benefit clearly seen only after 120 minutes of remineralization (P< 0.05). L caused the least SL for both enamel and dentin, which was further reduced after remineralization for 120 and 30 minutes, respectively (both P< 0.05). Overall, root dentin had significantly higher SL than enamel. Less abrasive dentifrice slurries were able to reduce toothbrushing abrasion on both enamel and root dentin. This protection was enhanced by remineralization for all abrasive levels on enamel, but only for L on root dentin. High-risk erosion patients should avoid highly abrasive toothpastes, as remineralization can only partially compensate for their deleterious effects on eroded dental surfaces. Lower abrasive toothpastes are recommended. Copyright©American Journal of Dentistry.

Dentistry: Careers in Dentistry

MedlinePlus

... in Dentistry e-mail Print Share Careers in Dentistry A dental education opens up a world of ... accredited training programs in your area . Careers in Dentistry Be a Dentist General Dentistry Dental Specialties Dental ...

Durability of resin cement bond to aluminium oxide and zirconia ceramics after air abrasion and laser treatment.

PubMed

Foxton, Richard M; Cavalcanti, Andrea N; Nakajima, Masatoshi; Pilecki, Peter; Sherriff, Martyn; Melo, Luciana; Watson, Timothy F

2011-02-01

The erbium laser has been introduced for cutting enamel and dentin and may have an application in the surface modification of high-strength aluminum oxide and zirconia ceramics. The aim of this study was to evaluate the durability of the bond of conventional dual-cured resin cements to Procera Al(2)O(3) and zirconium oxide ceramics after surface treatment with air abrasion and erbium laser. One hundred twenty Al(2)O(3) and 120 zirconia specimens measuring 3 × 3 × 0.7 mm(3) were divided equally into three groups, and their surfaces treated as follows: either untreated (controls), air abraded with Al(2)O(3) particles, or erbium-laser-treated at a power setting of 200 mJ. The surface of each specimen was then primed and bonded with one of two dual-cured resin cements (either SCP-100 Ceramic Primer and NAC-100 or Monobond S and Variolink II) using a 1-mm thick Tygon tube mold with a 0.75-mm internal bore diameter. After 24 hours and 6 months of water storage at 37°C, a microshear bond strength test was performed at a crosshead speed of 1 mm/min. Surface morphology was examined using a confocal microscope, and failure modes were observed using an optical microscope. The data were analyzed using the Kaplan-Meier nonparametric survival analysis. In the case of zirconia, air abrasion and Erbium:yttrium-aluminum-garnet (Er:YAG) laser treatment of the ceramic surface resulted in a significant reduction in the bond strengths of both resin cements after 6 months water storage; however, when the zirconia surface was left untreated, the SCP-100/NAC-100 group did not significantly reduce in bond strength. In the case of alumina, no treatment, air abrasion and Er:YAG laser treatment of the surface led to no significant reduction in the bond strengths of the three SCP-100/NAC-100 groups after 6 months water storage, whereas all three Monobond S/Variolink II groups showed a significant reduction. Er:YAG laser treatment of the zirconia surface did not result in a durable resin

Understanding wear in dentistry.

PubMed

Mair, L H

1999-01-01

Tooth wear is an increasing problem in dentistry. Traditionally, it has been divided into three categories: abrasion, attrition, and erosion. However, most clinical cases of tooth wear involve more than one of these processes. It is often easier to make a diagnosis by looking for the signs of the fundamental wear processes rather than trying to categorize the individual case. Wear can be caused by direct surface-to-surface wear, an intervening slurry, or a corrosive environment. Wear occurs during mastication, but also at other times, often at night. Although it may be possible to institute a preventive regimen, this will not always help the patient if his or her prime concern is esthetics. The same processes that cause tooth wear will cause wear to restorative materials. To diagnose and prevent wear, its processes must be understood.

Effect of air-abrasion regimens and fine diamond bur grinding on flexural strength, Weibull modulus and phase transformation of zirconium dioxide.

PubMed

Michida, Silvia Masae de Araújo; Kimpara, Estevão Tomomitsu; dos Santos, Claudinei; Souza, Rodrigo Othavio Assunção; Bottino, Marco Antonio; Özcan, Mutlu

2015-10-16

This study evaluated the effect of air abrasion and polishing regimens on the flexural strength of yttrium stabilized polycrystalline tetragonal zirconia (Y-TZP). From Y-TZP blocks (InCeram 2000 YZ Cubes; Vita Zahnfabrik, Bad Säckingen, Germany) 120 bars (25 mm × 4 mm × 1.2 mm) were obtained according to ISO 6872:2008 and randomly divided into 4 groups: Group C: (control) without surface treatment (n = 30); Group APA: Air abrasion with aluminum oxide (44 µm) (n = 30); Group SC: Silica-coating (CoJet, 30 µm) (n = 30); Group FD: Fine diamond bur (n = 30). Subsequently, all specimens were subjected to 4-point bending test (in distilled water at 37 °C) in a universal testing machine (EMIC DL 1000; São José dos Pinhais, Paraná, Brazil); cross-head speed: 0.5 mm/min). The characteristic strength (σ0) of each specimen was obtained from the flexural strength test and evaluated using Weibull analysis. X-ray diffraction analysis was utilized to quantity the monoclinic phase. The surface topography of specimens was analyzed using 3D optical profilometer and scanning electron microscopy (SEM) after surface conditioning methods. The flexural strength data (σ4p) were statistically analyzed by 1-way ANOVA, Tukey test (α = 0.05) and Weibull (m = modulus, σ0 = characteristic strength) were calculated. The mean ± standard deviations (MPa) of the groups were as follows: C: 1196.2 ± 284.2a; APA: 1369.7 ± 272.3a; SC: 1207.1 ± 229.7a and FD: 874.4 ± 365.4b. The values (m) and (σ0) were as follows: C: 4.5 and 1308.12; APA: 5.9 and 1477.88; SC: 6.0 and 1300.28; and FD: 2.6 and 985.901, respectively. Air particle abrasion with neither silica nor alumina showed significant difference compared to the control group but grinding with fine diamond bur impaired the flexural strength of the zirconia tested.

Abrasion of eroded and sound enamel by a dentifrice containing diamond abrasive particles

PubMed

Wegehaupt, Florian J.; Hoegger, Vanessa G. M.; Attin, Thomas

2017-07-24

Eroded enamel is more susceptible to abrasive wear than sound enamel. New toothpastes utilizing diamond particles as abrasives have been developed. The present study investigated the abrasive wear of eroded enamel by three commercially available toothpastes (one containing diamond particles) and compared it to the respective wear of sound enamel caused by these toothpastes. Seventy-two bovine enamel samples were randomly allocated to six groups (S1–S3 and E1–E3; n=12). Samples were submitted to an abrasive (S1–S3) or erosion plus abrasion (E1–E3) cycling. Per cycle, all samples were brushed (abrasion; 20 brushing stokes) with the following toothpastes: S1/E1: Signal WHITE SYSTEM, S2/E2: elmex KARIESSCHUTZ and S3-E3: Candida WHITE DIAMOND (diamond particles). Groups E1–E3 were additionally eroded with HCl (pH 3.0) for 2 min before each brushing procedure. After 30, 60 and 90 cycles enamel wear was measured by surface profilometry. Within the same toothpaste and same number of cycles, enamel wear due to erosion plus abrasion was significantly higher than due to mere abrasion. After 30, 60 and 90 cycles, no significant difference in the wear in groups S1 and S2 was observed while the wear in group E1 was significantly (p<0.05, ANOVA, Scheffecyc) lower than that in group E2. After 90 cycles, wear in group S3 was about 5 times higher than that in group S2, while wear in group E3 was about 1.3 times higher than that in group E2. As compared to the other two investigated toothpastes, the dentifrice containing diamond particles caused slightly higher abrasive wear of eroded enamel and distinctly higher wear of sound enamel compared to the conventional toothpastes under investigation.

Microleakage of class V resin composite restorations after bur, air-abrasion or Er:YAG laser preparation.

PubMed

Corona, S A; Borsatto, M; Dibb, R G; Ramos, R P; Brugnera, A; Pécora, J D

2001-01-01

This in vitro study compared the microleakage of Class V resin composite restorations placed in cavities prepared with a high-speed dental bur, air-abrasion or Er:YAG laser. Twenty sound extracted human third molars were selected and randomly assigned to four equal Groups (n=10): Group I, cavities were cut by dental drill at high-speed; Group II, aluminum oxide air-abrasion was used for cavity preparation, and in Groups III and IV, cavities were prepared by Er:YAG laser. Following cavity preparation, Groups I and II were acid-etched, Group III was treated only by Er:YAG laser and Group IV was conditioned by Er:YAG laser followed by acid-etching. Cavities were restored (Single Bond + Z-100) and the teeth stored for seven days in distilled water. Then, the restorations were polished and the specimens thermocycled, immersed in a 0.2% Rhodamine solution, sectioned and analyzed for leakage at the occlusal (enamel) and cervical (dentin/cementum) interfaces using an optical microscope connected to a video camera. The images were digitized and software was utilized for microleakage assessment. Upon analyzing the results, statistically significant differences (p<0.01) between the occlusal and cervical regions for all groups was observed, and, as a rule, there was better marginal sealing at the enamel margins. The highest degree of infiltration was observed for cavities prepared and treated exclusively by Er:YAG (Group III). The other experimental groups showed statistical similarities in the amount of marginal leakage at the enamel margins. However, at the cervical margins, there was a significant difference (p<0.05) between Group I and the remaining groups. None of the techniques completely eliminated marginal microleakage at the dentin/ cementum margins.

Effect of air-abrasion on the retention of zirconia ceramic crowns luted with different cements before and after artificial aging.

PubMed

Shahin, Ramez; Kern, Matthias

2010-09-01

The purpose of this in vitro study was to evaluate the effect of intaglio surface air-abrasion on the retention of CAD/CAM produced zirconia ceramic crowns cemented with three different types of cement. In addition the influence of artificial aging in masticatory simulator and thermocycling was tested. Extracted human premolars were prepared for all-ceramic crowns (12 degrees taper, 3 mm axial length). CAD/CAM zirconia crowns were manufactured. Half of the crowns were air-abraded with 50 microm alumina particles at 0.25 MPa, the rest was left as machined. The crowns were luted with zinc phosphate cement (Hoffmann), glass ionomer cement (Ketac Cem), or composite resin (Panavia 21), subgroups were either stored for 3 days in 37 degrees water bath or stored for 150 days in 37 degrees water bath, with additional 37,500 thermal cycles (5-55 degrees) and 300,000 cycles dynamic loading with 5 kg in a masticatory simulator. Then crown retention was measured in tension at a crosshead speed of 2 mm/min using a universal testing machine. Statistical analysis was performed with three-way ANOVA. Mean retention values were ranged from 2.8 to 7.1 MPa after 3 days and from 1.6 to 6.1 MPa after artificial aging. Air-abrasion significantly increased crown retention (p<0.001), while artificial aging decreased retention (p=0.017). In addition, the luting material had a significant influence on retention (p<0.001) with the adhesive luting resin providing the highest retention. The use of phosphate monomer containing composite resin on air-abraded zirconia ceramic can be recommended as most retentive luting method. Copyright 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

[Paradigm shift in conservative dentistry: from a mechanistic to a prevention-oriented perception].

PubMed

Hellwig, E; Altenburger, M

2011-09-01

The application of different preventive measures has resulted in a decline of clinically detectable carious lesions in children and adolescents. Not only have caries symptoms changed significantly, but the number of extracted teeth in adults has decreased. Due to these epidemiological facts, modern conservative dentistry is based on a careful risk analysis and caries diagnosis, which also takes into consideration biological and psychosocial components of caries etiology. Conservative dentistry will fail if the dentists are only interested in repairing defects. Simultaneous with the positive outcome of prevention, some unanswered problems have arisen, for which there are no adequate solutions. In young children, caries prevalence is still high and the restorative care of these primary teeth should be improved. For adolescents, early detection of carious lesions should be improved and polarization of caries prevalence should be eliminated. In older adults, evidence-based therapy options for treatment of erosions, abrasions, and root caries are lacking. For seniors needing general care, preventive and restorative concepts should be established.

Effect of abrasive grit size on wear of manganese-zinc ferrite under three-body abrasion

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

1987-01-01

Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and deformed layers produced in single-crystal Mn-Zn ferrites under three-body abrasion. The abrasion mechanism of Mn-Zn ferrite changes drastically with the size of abrasive grits. With 15-micron (1000-mesh) SiC grits, abrasion of Mn-Zn ferrite is due principally to brittle fracture; while with 4- and 2-micron (4000- and 6000-mesh) SiC grits, abrasion is due to plastic deformation and fracture. Both microcracking and plastic flow produce polycrystalline states on the wear surfaces of single-crystal Mn-Zn ferrites. Coefficient of wear, total thickness of the deformed layers, and surface roughness of the wear surfaces increase markedly with an increase in abrasive grit size. The total thicknesses of the deformed layers are 3 microns for the ferrite abraded by 15-micron SiC, 0.9 microns for the ferrite abraded by 4-micron SiC, and 0.8 microns for the ferrite abraded by 1-micron SiC.

Effect of laser and air abrasion pretreatment on the microleakage of a fissure sealant applied with conventional and self etch adhesives.

PubMed

Tirali, R E; Celik, C; Arhun, N; Berk, G; Cehreli, S B

2013-01-01

The purpose of this study was to investigate the effects of different pretreatment protocols along with different bonding agents on the microleakage of a fissure sealant material. A total of 144 freshly extracted noncarious human third molars were used The teeth were randomly assigned into three groups with respect to the pretreatment protocol employed: A. Air Abrasion B. Er,Cr:YSGG laser C. No pretreatment (Control). In each group specimens were further subjected to one of the following procedures before application of the sealant: 1. %36 Phosphoric acid-etch (AE) (DeTrey Conditioner 36/Denstply, UK) 2.AE+Prime&Bond NT (Dentsply, UK) 3. Clearfil S3 Bond (Kuraray, Japan) 4. Clearfil SE Bond (Kuraray, Japan). All teeth were sealed with the same fissure sealant material (Conseal F/SDI, Australia). Sealed teeth were further subjected to thermocycling, dye penetration test, sectioning and quantitative image analysis. Statistical evaluation of the microleakage data was performed with two way independent ANOVA and multiple comparisons test at p = 0.05. For qualitative evaluation 2 samples from each group were examined under Scanning Electron Microscopy. Microleakage was affected by both the type of pretreatment and the subsequent bonding protocols employed (p < 0.05). Overall, the highest (Mean = 0.36 mm) and lowest (Mean = 0.06 mm) microleakage values were observed in samples with unpretreated enamel sealed by S3+Conseal F and samples with laser pretreated enamel sealed by Acid Etch+Prime&-Bond+Conseal F protocols, respectively (p < 0.05). In the acid-etch group samples pretreated with laser yielded in slightly lower microleakage scores when compared with unpretreated samples and samples pretreated with air abrasion but the statistical significance was not important (p = 0,179). Similarly, when bonding agent is applied following acid-etching procedure, microleakage scores were not affected from pretreatment protocol (p = 0,615) (intact enamel/laser or air-abrasion). For

Propelled abrasive grit for weed control in organic silage corn

USDA-ARS?s Scientific Manuscript database

Weed management in organic farming requires many strategies to accomplish acceptable control and maintain crop yields. This two-year field study used air propelled abrasive grit for in-row weed control in a silage corn system. Corncob grit was applied as a single application at corn vegetative growt...

Do Abrasives Play a Role in Toothpaste Efficacy against Erosion/Abrasion?

PubMed

Ganss, Carolina; Möllers, Maike; Schlueter, Nadine

2017-01-01

Abrasives may counteract the efficacy of anti-erosion toothpastes either due to physical effects or due to interaction with active agents. This study aimed to investigate whether the amount of abrasives is a determinant for the efficacy of Sn2+-containing toothpastes with or without chitosan additive. Enamel samples were eroded (0.50 wt% citric acid, pH 2.5; 6 × 2 min/day) on a shaking desk - 30/min in experiment 1 (E1) and 35/min in experiments 2 (E2) and 3 (E3) - and immersed in toothpaste slurries (2 × 2 min). Half of the samples were additionally brushed (15 s, load 200 g) within the immersion time. The toothpastes contained 0, 5, 10, 15, and 20% silica. In E1 and E2 the active ingredients were F- (700 ppm as amine fluoride, 700 ppm as NaF) and Sn2+ (3,500 ppm as SnCl2); in E3 chitosan (0.5%) was additionally added. The placebo contained 20% silica. Tissue loss was determined profilometrically. In E1, slurries completely inhibited tissue loss; distinct surface deposits occurred. With brushing, tissue loss significantly increased up to an abrasive content of 10%, but decreased significantly with higher amounts; 20% silica revealed similar values as the abrasive-free formulation. In E2, all slurries inhibited tissue loss distinctly irrespective of the amounts of abrasives. With brushing, a similar trend as in E1 was observed but with much less efficacy. The chitosan-containing formulations in E3 were much more effective; similar results as in E1 were found. In conclusion, the amount of abrasives had no effect when toothpastes were applied as slurries, but played an important role with brushing. © 2016 S. Karger AG, Basel.

Air-particle abrasion on zirconia ceramic using different protocols: effects on biaxial flexural strength after cyclic loading, phase transformation and surface topography.

PubMed

Souza, Rodrigo O A; Valandro, Luiz F; Melo, Renata M; Machado, João P B; Bottino, Marco A; Ozcan, Mutlu

2013-10-01

This study evaluated the effect of different air-particle abrasion protocols on the biaxial flexural strength and structural stability of zirconia ceramics. Zirconia ceramic specimens (ISO 6872) (Lava, 3M ESPE) were obtained (N=336). The specimens (N=118, n=20 per group) were randomly assigned to one of the air-abrasion protocols: Gr1: Control (as-sintered); Gr2: 50 µm Al2O3 (2.5 bar); Gr3: 50 µm Al2O3 (3.5 bar); Gr4: 110 µm Al2O3(2.5 bar); Gr5: 110 µm Al2O3 (3.5 bar); Gr6: 30 µm SiO2 (2.5 bar) (CoJet); Gr7: 30 µm SiO2(3.5 bar); Gr8: 110 µm SiO2 (2.5 bar) (Rocatec Plus); and Gr9: 110 µm SiO2 (3.5 bar) (duration: 20 s, distance: 10 mm). While half of the specimens were tested immediately, the other half was subjected to cyclic loading in water (100,000 cycles; 50 N, 4 Hz, 37 °°C) prior to biaxial flexural strength test (ISO 6872). Phase transformation (t→m), relative amount of transformed monoclinic zirconia (FM), transformed zone depth (TZD) and surface roughness were measured. Particle type (p=0.2746), pressure (p=0.5084) and cyclic loading (p=0.1610) did not influence the flexural strength. Except for the air-abraded group with 110 µm Al2O3 at 3.5 bar, all air-abrasion protocols increased the biaxial flexural strength (MPa) (Controlnon-aged: 1,030 ± 153, Controlaged: 1,138 ± 138; Experimentalnon-aged: 1,307 ± 184-1,554 ± 124; Experimentalaged: 1,308 ± 118-1,451 ± 135) in both non-aged and aged conditions, respectively. Surface roughness (Ra) was the highest with 110 µm Al2O3(0.84 µm. FM values ranged from 0% to 27.21%, higher value for the Rocatec Plus (110 µm SiO2) and 110 µm Al2O3 groups at 3.5 bar pressure. TZD ranged between 0 and 1.43 µm, with the highest values for Rocatec Plus and 110 µm Al2O3 groups at 3.5 bar pressure. Copyright © 2013 Elsevier Ltd. All rights reserved.

Physics of loose abrasive microgrinding.

PubMed

Golini, D; Jacobs, S D

1991-07-01

This study examined the physics of loose abrasive microgrinding (grinding with micron and submicron sized abrasives). More specifically, it focused on the transition from brittle to ductile mode grinding which occurs in this region of abrasive sizes. Process dependency on slurry chemistry was the primary area of emphasis and was studied for diamond abrasives varying in size from 3.0 to 0.75 microm on both ULE and Zerodur, with emphasis on ULE. Ductile mode grinding was achieved with smaller abrasives, as expected, however two significant discoveries were made. The first observation was that by simply changing slurry chemistry, it was possible to induce the transition from brittle fracture to ductile mode grinding in ULE. This transition point could be intentionally moved about for diamonds 3.0-0.75 microm in diameter. For any given abrasive size within these limits, either brittle fracture or ductile removal may be achieved, depending on the slurry used to suspend the diamonds. Several slurries were studied, including water, a series of homologous n-alcohols, and other solvents chosen for properties varying from molecular size to dielectric constant and zeta potential. The study revealed that this slurry dependency is primarily a Rebinder effect. The second finding was that a tremendous amount of surface stress is introduced in loose abrasive ductile mode grinding. This stress was observed when the Twyman Effect in ULE plates increased by a factor of 4 in the transition from the brittle to the ductile mode. An assessment of the cause of this stress is discussed.

Abrasion of acrylic veneers by simulated toothbrushing.

PubMed

Xu, H C; Söremark, R; Wiktorsson, G; Wang, T; Liu, W Y

1984-12-01

The abrasion responses were tested on four acrylic veneer materials, K + B Plus, K + B 75, Isosit, and Ivocron. The studies were performed in two independent research laboratories. Two different brushing machines were used with an abrasive slurry. The results were used for comparing the degree of abrasion for the resin materials. Three analytical methods of measuring the degree of abrasive wear were used: surface profile measurement, microscopic evaluation, and measurement of loss of volume. Isosit showed the best abrasion resistance of the four materials tested.

Minimal intervention dentistry - a new frontier in clinical dentistry.

PubMed

Mm, Jingarwar; Nk, Bajwa; A, Pathak

2014-07-01

Minimally invasive procedures are the new paradigm in health care. Everything from heart bypasses to gall bladder, surgeries are being performed with these dynamic new techniques. Dentistry is joining this exciting revolution as well. Minimally invasive dentistry adopts a philosophy that integrates prevention, remineralisation and minimal intervention for the placement and replacement of restorations. Minimally invasive dentistry reaches the treatment objective using the least invasive surgical approach, with the removal of the minimal amount of healthy tissues. This paper reviews in brief the concept of minimal intervention in dentistry.

An epidemiologic approach to toothbrushing and dental abrasion.

PubMed

Bergström, J; Lavstedt, S

1979-02-01

Abrasion lesions were recorded in 818 individuals representing the adult population of 430,000 residents of the Stockholm region, Sweden. The subjects were asked about toothbrushing habits, toothbrush quality and dentifrice usage; these factors were related to abrasion criteria. Abrasion was prevalent in 30% and wedge-like or deep depressions were observed in 12%. The relationship between abrasion and toothbrushing was evident, the prevalence and severity of abrasion being correlated to toothbrushing consumption. The importance of the toothbrushing technique for the development of abrasion lesions was elucidated. Horizontal brushing technique was strongly correlated to abrasion. It was demonstrated by treating the data with the statistical AID analysis that toothbrushing factors related to the individual (brushing frequency and brushing technique) exert a greater influence than material-oriented toothbrushing factor such as dentifrice abrasivity and bristle stiffness.

Minimal Intervention Dentistry – A New Frontier in Clinical Dentistry

PubMed Central

NK., Bajwa; A, Pathak

2014-01-01

Minimally invasive procedures are the new paradigm in health care. Everything from heart bypasses to gall bladder, surgeries are being performed with these dynamic new techniques. Dentistry is joining this exciting revolution as well. Minimally invasive dentistry adopts a philosophy that integrates prevention, remineralisation and minimal intervention for the placement and replacement of restorations. Minimally invasive dentistry reaches the treatment objective using the least invasive surgical approach, with the removal of the minimal amount of healthy tissues. This paper reviews in brief the concept of minimal intervention in dentistry. PMID:25177659

Comparison between different interdental stripping methods and evaluation of abrasive strips: SEM analysis.

PubMed

Grippaudo, Cristina; Cancellieri, Daniela; Grecolini, Maria E; Deli, Roberto

2010-01-01

The aim of this study was to evaluate the morphological effects and the surface irregularities produced by different methods of mechanical stripping (abrasive strips and burs) and chemical stripping (37% orthophosphoric acid) and the surface changes following the finishing procedures (polishing strips) or the subsequent application of sealants, in order to establish the right stripping method that can guarantee the smoothest surface. We have also analysed the level of wear on the different abrasive strips employed, according to their structure. 160 proximal surfaces of 80 sound molar teeth extracted for orthodontic and periodontal reasons, were divided into: 1 control group with non-treated enamel proximal surfaces and 5 different groups according to the stripping method used, were observed with scanning electron microscopy (SEM). Each one of the 5 treated groups was also divided into 3 different subgroups according to the finishing procedures or the subsequent application of sealants. The finishing stage following the manual reduction proves to be fundamental in reducing the number and depth of grooves created by the stripping. After the air rotor stripping method, the use of sealants is advised in order to obtain a smoother surface. The analysis of the combinations of mechanical and chemical stripping showed unsatisfactory results. Concerning the wear of the strips, we have highlighted a different abrasion degree for the different types of strips analysed with SEM. The enamel damages are limited only if the finishing procedure is applied, independently of the type of abrasive strip employed. It would be advisable, though clinically seldom possible, the use of sealants after the air rotor stripping technique. Copyright © 2010 Società Italiana di Ortodonzia SIDO. Published by Elsevier Srl. All rights reserved.

Cosmetic Dentistry

MedlinePlus

If you have stained, broken or uneven teeth, cosmetic dentistry can help. Cosmetic dentistry is different from orthodontic treatment, which can straighten your teeth with braces or other devices. Cosmetic dental ...

A brief history of aerospace dentistry.

PubMed

Savage, D Keith

2002-07-01

In April 2000, the National Academy of Sciences Institute of Medicine (NAS/IOM) Committee on Space Medicine held a workshop under contract with the National Aeronautics and Space Administration (NASA) to explore "innovative terrestrial medical care." There was also a NAS/IOM panel held on "Space Dentistry: Maintaining Astronauts' Oral Health on Long Missions." Air Force Dental Officer Col. Shannon E. Mills chaired the dental committee. Many questions were raised but few answers were available. Prevention was emphasized with the hope that within twenty to thirty years there may be a number of astronaut candidates with no existing dental restorations and with optimum oral health. However, there remains the concern that trauma to teeth could occur within the confines of a zero gravity space capsule as crew members carry out their daily responsibilities. The possibility is evident considering the duration of a space flight to Mars and back could require up to three years. The dental concerns of a space mission are only a small part of a much larger team effort, however, it is one not to be overlooked. An historical review of dentistry's involvement with America's flight and space programs of the 20th Century would be prudent. Many of same questions asked today were addressed in the early days of aviation dentistry as it transitioned into aerospace dentistry. Any past research and experiences would help serve as a foundation to build upon.

Study on design of light-weight super-abrasive wheel

NASA Astrophysics Data System (ADS)

Nohara, K.; Yanagihara, K.; Ogawa, M.

2018-01-01

Fixed-abrasive tool, also called a grinding wheel, is produced by furnacing abrasive compound which contains abrasive grains and binding powder such as vitrified materials or resins. Fixed-abrasive tool is installed on spindle of grinding machine. And it is given 1,800-2,000 min-1 of spindle rotation for the usage. The centrifugal fracture of the compound of fixed- abrasive tool is one of the careful respects in designing. In recent years, however, super-abrasive wheel as a fixed-abrasive tool has been developed and applied widely. One of the most characteristic respects is that metal is applied for the body of grinding-wheel. The strength to hold abrasive grain and the rigidity of wheel become stronger than those of general grinding wheel, also the lifespan of fixed-abrasive tool becomes longer. The weight of fixed-abrasive tool, however, becomes heavier. Therefore, when the super-abrasive wheel is used, the power consumption of spindle motor becomes larger. It also becomes difficult for the grinding-wheel to respond to sudden acceleration or deceleration. Thus, in order to reduce power consumption in grinding and to obtain quicker frequency response of super-abrasive wheel, the new wheel design is proposed. The design accomplishes 46% weight reduction. Acceleration that is one second quicker than that of conventional grinding wheel is obtained.

Corneal Abrasions

MedlinePlus

... the doctor looks at the eye under a light that is filtered cobalt blue. The fluorescein causes the abrasion to glow bright green under the light. The doctor also might do a standard ophthalmic ...

Propelled abrasive grit applications for weed management in transitional corn grain production systems

USDA-ARS?s Scientific Manuscript database

Weed control is challenging to farmers who are transitioning from production systems that use synthetic herbicides to organic systems. A two-year field study examined weed control efficacy and corn grain yield of air-propelled corncob grit abrasion for in-row weed control. Grits were applied based o...

Ceramic-bonded abrasive grinding tools

DOEpatents

Holcombe, C.E. Jr.; Gorin, A.H.; Seals, R.D.

1994-11-22

Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

Ceramic-bonded abrasive grinding tools

DOEpatents

Holcombe, Jr., Cressie E.; Gorin, Andrew H.; Seals, Roland D.

1994-01-01

Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

Mars Pathfinder Wheel Abrasion Experiment Ground Test

NASA Technical Reports Server (NTRS)

Keith, Theo G., Jr.; Siebert, Mark W.

1998-01-01

The National Aeronautics and Space Administration (NASA) sent a mission to the martian surface, called Mars Pathfinder. The mission payload consisted of a lander and a rover. The primary purpose of the mission was demonstrating a novel entry, descent, and landing method that included a heat shield, a parachute, rockets, and a cocoon of giant air bags. Once on the surface, the spacecraft returned temperature measurements near the Martian surface, atmosphere pressure, wind speed measurements, and images from the lander and rover. The rover obtained 16 elemental measurements of rocks and soils, performed soil-mechanics, atmospheric sedimentation measurements, and soil abrasiveness measurements.

Cleaning and modification of intraorally contaminated titanium discs with calcium phosphate powder abrasive treatment.

PubMed

Tastepe, Ceylin S; Liu, Yuelian; Visscher, Corine M; Wismeijer, Daniel

2013-11-01

The aim of this study was to evaluate the cleaning efficiency on intraorally contaminated titanium discs by using calcium phosphate and air powder abrasive (APA) treatment. The modification of titanium surface (SLA) was evaluated and compared with the conventional air powder abrasive methods and phosphoric acid. This treatment modality might give new perspectives for peri-implant surface treatment. A total of 36 SLA surface titanium discs were kept in the human mouth for 48 h by 14 volunteers. The intraorally contaminated discs were stained with erythrosine dye to make the biofilm visible. Discs were randomly assigned to one of the six groups: APA without powder-only water and air (Control). APA with Hydroxylapatite (HA). APA with Hydroxylapatite and Calcium Phosphate (HA + TCP). APA with Titanium Dioxide (TiO2). APA with EMS Soft Subgingival powder (EMS). Phosphoric Acid. Light microscope photos were taken during the treatment. Following the cleaning, the residual biofilm, surface changes, and surface chemical content were evaluated using Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray Spectroscopy (EDS). A systematic random sampling protocol and a point counting method were applied for the quantitative evaluation of the remaining biofilm. Multiple comparisons within and between groups are performed by Kruskall Wallis test and if significant Mann-Whitney U-test as post hoc testing is applied. The significance level was P < 0.05. All methods with the exception of phosphoric acid could decrease the initial amount of biofilm significantly. Among all air powder abrasive treatments, the HA + TCP group showed the best results with 99% biofilm removal, followed by HA and EMS powders. The cleaning method caused minimal changes to the surface structure. With the exception of the control group, all air powder applications caused sharp edges around the grooves in the implant surface to be rounded. TiO2 powder caused less change than HA and HA + TCP. Phosphoric

Awareness, knowledge, and attitude of dentistry students in Kerman towards evidence-based dentistry

PubMed Central

Sarani, Arezoo; Sarani, Melika; Abdar, Mohammad Esmaeli; Abdar, Zahra Esmaeili

2016-01-01

Introduction Evidence-based care helps dentists provide quality dental services to patients, and such care is based on the use of reliable information about treatment and patient care from a large number of papers, books, and published textbooks. This study aimed to determine the knowledge, awareness, and attitude of dentistry students towards evidence-based dentistry. Methods In this cross-sectional study, all dentistry students who were studying in their sixth semester and higher in the Kerman School of Dentistry (n = 73) were studied. The data were analyzed using SPSS version 17 and the independent-samples t-tests and the ANOVA test. Results The means of the students’ knowledge, awareness, and attitude scores were 29.2 ± 10.8, 29.9 ± 8.12 and 44.5 ± 5.3, respectively. Among demographic variables, only the number of semesters showed a significant difference with knowledge, awareness, and attitude of dentistry students toward evidence-based dentistry (p = 0.001). Conclusion According to the results of this study, knowledge and awareness of dentistry students at Kerman University of Medical Sciences towards evidence-based dentistry were average and have a neutral attitude. Thus, providing necessary training in this regard will cause promoting the knowledge, awareness, and improved attitudes of dentistry students. PMID:27382446

Abrasion by aeolian particles: Earth and Mars

NASA Technical Reports Server (NTRS)

Greeley, R.; Marshall, J. R.; White, B. R.; Pollack, J. B.; Marshall, J.; Krinsley, D.

1984-01-01

Estimation of the rate of aeolian abrasion of rocks on Mars requires knowledge of: (1) particle flux, (2) susceptibilities to abrasion of various rocks, and (3) wind frequencies on Mars. Fluxes and susceptibilities for a wide range of conditions were obtained in the laboratory and combined with wind data from the Viking meteorology experiment. Assuming an abundant supply of sand-sized particles, estimated rates range up to 2.1 x 10 to the minus 2 power cm of abrasion per year in the vicinity of Viking Lander 1. This rate is orders of magnitude too great to be in agreement with the inferred age of the surface based on models of impact crater flux. The discrepancy in the estimated rate of abrasion and the presumed old age of the surface cannot be explained easily by changes in climate or exhumation of ancient surfaces. The primary reason is thought to be related to the agents of abrasion. At least some sand-sized (approx. 100 micrometers) grains appear to be present, as inferred from both lander and orbiter observations. High rates of abrasion occur for all experimental cases involving sands of quartz, basalt, or ash. However, previous studies have shown that sand is quickly comminuted to silt- and clay-sized grains in the martian aeolian regime. Experiments also show that these fine grains are electrostatically charged and bond together as sand-sized aggregates. Laboratory simulations of wind abrasion involving aggregates show that at impact velocities capable of destroying sand, aggregates from a protective veneer on the target surface and can give rise to extremely low abrasion rates.

The effect of microstructure on abrasive wear of steel

NASA Astrophysics Data System (ADS)

Kešner, A.; Chotëborský, R.; Linda, M.

2017-09-01

Abrasive wear of agricultural tools is one of the biggest problems in currently being. The amount of abrasive wear, depending on the microstructure, has been investigated in this work. Steels 25CrMo4 and 51CrV4 were used in this work to determine the effect of the microstructure on the abrasive wear. These steels are commonly used for components that have to withstand abrasive wear.SEM analysis was used to detect the microstructure. The standardized ASTM G65 method was used to compare the abrasive wear of steels. The results show that the abrasive wear depends on the microstructure of steels.

Ultrasonic Abrasive Removal Of EDM Recast

NASA Technical Reports Server (NTRS)

Mandel, Johnny L.; Jacobson, Marlowe S.

1990-01-01

Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

Exposure to crystalline silica in abrasive blasting operations where silica and non-silica abrasives are used.

PubMed

Radnoff, Diane L; Kutz, Michelle K

2014-01-01

Exposure to respirable crystalline silica is a hazard common to many industries in Alberta but particularly so in abrasive blasting. Alberta occupational health and safety legislation requires the consideration of silica substitutes when conducting abrasive blasting, where reasonably practicable. In this study, exposure to crystalline silica during abrasive blasting was evaluated when both silica and non-silica products were used. The crystalline silica content of non-silica abrasives was also measured. The facilities evaluated were preparing metal products for the application of coatings, so the substrate should not have had a significant contribution to worker exposure to crystalline silica. The occupational sampling results indicate that two-thirds of the workers assessed were potentially over-exposed to respirable crystalline silica. About one-third of the measurements over the exposure limit were at the work sites using silica substitutes at the time of the assessment. The use of the silica substitute, by itself, did not appear to have a large effect on the mean airborne exposure levels. There are a number of factors that may contribute to over-exposures, including the isolation of the blasting area, housekeeping, and inappropriate use of respiratory protective equipment. However, the non-silica abrasives themselves also contain silica. Bulk analysis results for non-silica abrasives commercially available in Alberta indicate that many contain crystalline silica above the legislated disclosure limit of 0.1% weight of silica per weight of product (w/w) and this information may not be accurately disclosed on the material safety data sheet for the product. The employer may still have to evaluate the potential for exposure to crystalline silica at their work site, even when silica substitutes are used. Limited tests on recycled non-silica abrasive indicated that the silica content had increased. Further study is required to evaluate the impact of product recycling

[Dentistry students' reasons for choosing dentistry as a career in Damascus University].

PubMed

Mashlah, A M

2012-05-01

This cross-sectional questionnaire survey assessed the motives for choosing dentist as a profession among dentistry students at Damascus University, Syrian Arab Republic. A total of 408 undergraduate students (233 males and 175 females) aged 18-23 years were selected randomly from students in the second, third and fourth years of dentistry study. They completed a questionnaire that enquired about their reasons for studying dentistry as well as their sociodemographic characteristics. The number of admissions in females had increased over the 3 years. Most parents of the students were university-educated. The main motivation for choosing dentistry was as a means to achieve personal goals, including getting a good job abroad, having financial independence, and attaining a good reputation. There were significant differences between the sexes with regard to the reasons for choosing dentistry.

New Rock Abrasivity Test Method for Tool Life Assessments on Hard Rock Tunnel Boring: The Rolling Indentation Abrasion Test (RIAT)

NASA Astrophysics Data System (ADS)

Macias, F. J.; Dahl, F.; Bruland, A.

2016-05-01

The tunnel boring machine (TBM) method has become widely used and is currently an important presence within the tunnelling industry. Large investments and high geological risk are involved using TBMs, and disc cutter consumption has a great influence on performance and cost, especially in hard rock conditions. Furthermore, reliable cutter life assessments facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory tests for rock abrasivity assessments are needed. A new abrasivity test method by rolling disc named Rolling Indentation Abrasion Test (RIAT) has been developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than the traditionally used methods. Wear by rolling contact on intact rock samples is introduced and several rock types, covering a wide rock abrasiveness range, have been tested by RIAT. The RIAT procedure indicates a great ability of the testing method to assess abrasive wear on rolling discs. In addition and to evaluate the newly developed RIAT test method, a comprehensive laboratory testing programme including the most commonly used abrasivity test methods and the mineral composition were carried out. Relationships between the achieved results from conventional testing and RIAT results have been analysed.

Characterization of fine abrasive particles for optical fabrication

NASA Astrophysics Data System (ADS)

Funkenbusch, Paul D.; Zhou, Y. Y.; Takahashi, Toshio; Quesnel, David J.; Lambropoulos, John C.

1995-08-01

Material removal during fine grinding operations is accomplished primarily by the action of individual abrasive particles on the glass surface. The mechanical properties of the abrasive are therefore important. Unfortunately it is difficult to directly measure the mechanical response of abrasives once they reach the scale of approximately 10 microns. As a result mechanical properties of fine abrasives are sometimes characterized in terms of an empirical `friability', based on the response of the abrasive to crushing by a metal ball in a vial. In this paper we report on modeling/experiments designed to more precisely quantify the mechanical properties of fine abrasives and ultimately to relate them to the conditions experienced by bound particles during grinding. Experiments have been performed on various types and sizes of diamond abrasives. The response of the particles is a strong function of the loading conditions and can be tracked by changing the testing parameters. Diamond size is also found to play a critical role, with finer diamonds less susceptible to fracture. A micromechanical model from the literature is employed estimate the forces likely to be seen during testing. We are also developing dynamic models to better predict the forces experienced during `friability' testing as a function of the testing parameters.

Experimental Rock-on-Rock Abrasive Wear Under Aqueous Conditions: its Role in Subglacial Abrasion

NASA Astrophysics Data System (ADS)

Rutter, E. H.; Lee, A. G.

2003-12-01

We have determined experimentally the rate of abrasive wear of rock on rock for a range of rock types as a function of normal stress and shear displacement. Unlike abrasive wear in fault zones, where wear products accumulate as a thickening gouge zone, in our experiments wear particles were removed by flowing water. The experiments are thus directly pertinent to one of the most important processes in subglacial erosion, and to some extent in river incision. Wear was produced between rotating discs machined from rock samples and measured from the progressive approach of the disc axes towards each other under various levels of normal load. Shear displacements of several km were produced. Optical and scanning electron microscopy were used to study the worn rock surfaces, and particle size distributions in wear products were characterized using a laser particle size analyzer. Rock types studied were sandstones of various porosities and cement characteristics, schists and a granite. In all cases abrasion rate decreased logarithmically with displacement by up to 2 orders of magnitude until a steady state was approached, but only after at least 1 km displacement. The more porous, less-well cemented rocks wore fastest. Amount of abrasion could be characterized quantitatively using an exponentially decaying plus a steady-state term. Wear rate increased non-linearly with normal contact stress, apparently to an asymptote defined by the unconfined compressive strength. Microstructural study showed that the well-cemented and/or lowest porosity rocks wore by progressive abrasion of grains without plucking, whereas whole grains were plucked out of weakly-cemented and/or more porous rocks. This difference in behavior was reflected in wear-product particle size distributions. Where whole-grain plucking was possible, wear products were dominated by particles of the original grain size rather than finer rock flour. Comparison of our results to glacier basal abrasive wear estimated

Origins of Argentinean dentistry and development of teaching.

PubMed

Siutti, O W

2001-07-01

The history of the legal practice of dentistry in the Rio de la Plata region is given. The first diplomas were given in 1891 by the Medical Tribunal, before the creation of the dental school in Buenos Aires. The inauguration of teaching courses and the different teaching plans, as well as the biography of the teachers who initiated the teaching in Argentina are presented as are the creation of the School of Dentistry and the appearance of the three schools of the College of Medical Sciences in the monumental new building. Portraits of the teachers Etcheparborda, Pereira, Erausquin and Guardo, crafters of the old school are presented, together with those of the administrators of the university complex and the College, Profs. Dr. Jose Arce and Ricardo C. Guardo.

Solidification/stabilization of spent abrasives and use as nonstructural concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brabrand, D.J.; Loehr, R.C.

1993-01-01

Tons of spent abrasives result each year from the removal of old paint from bridges. Because the spent abrasives contain metals from the paint, some spent abrasives may be considered hazardous by the Toxicity Characteristic (TC) criteria. Incorporation of the spent blasting abrasives in nonstructural concrete (rip-rap, dolphins) offers an opportunity to recycle the spent abrasives while immobilizing potentially leachable metals. This study focused on the Portland Cement Solidification/Stabilization (S/S) of spent blasting abrasives taken from a bridge located in Southeast Texas. The study examined (a) the cadmium, chromium, and lead concentrations in extracts obtained by using the Toxicity Characteristicmore » Leaching Procedure (TCLP) and (b) the compressive strengths of Portland Cement mixes that contained different amounts of the spent abrasives. Performance was measured by meeting the TC criteria as well as the requirements for compressive strength. Study results indicated that considerable quantities of these spent abrasives can be solidified/stabilized while reducing the leachability of cadmium, chromium, and lead and producing compressive strengths over 6,895 kN/m[sup 2] (1,000 psi).« less

Green dentistry, a metamorphosis towards an eco-friendly dentistry: a short communication.

PubMed

Rastogi, Varun; Sharma, Rachna; Yadav, Lalita; Satpute, Pranali; Sharma, Vandana

2014-07-01

Dentistry is most importantly and foremost a healing profession. In today's world, it is very necessary to understand the importance of being eco-friendly in every facet of our lives, including dental practice which has a huge impact on the environment due to the large amount of metallic waste generated by various dental procedures along with excessive use of water and electricity, which specifically emphasis the thrust to move towards 'Green dentistry'. Green dentistry is an innovative way of dental practice which is environment friendly and at the same time conserves money and time by reducing waste, conserving energy and decreasing pollution with the use of latest techniques and procedures. Green dentistry therefore, protects the environment and mankind from the hazards of rapid urbanisation in developing countries. The authors wish to emphasize the practice of eco-friendly, green dentistry in a developing country like India which needs to conserve resources and curb environmental pollution.

To Evaluate Effect of Airborne Particle Abrasion using Different Abrasives Particles and Compare Two Commercial Available Zirconia on Flexural Strength on Heat Treatment.

PubMed

Prasad, Hari A; Pasha, Naveed; Hilal, Mohammed; Amarnath, G S; Kundapur, Vinaya; Anand, M; Singh, Sumeet

2017-06-01

AMANNGIRRBACH specimens gave a higher value compare to the UPCERA specimens. The study also revealed that the heat treatment of the specimens gave significant value ( P <0.001) compared to the control group, but heat treatment following the air abrasion reduces the fracture strength of the sample than the air abraded group. Within the limitation of this study, it is concluded that, the in vitro fracture strength of Zirconia specimens treated with an airborne abrasion both on the veneering surface (50 µm silica coated Al2O3) and the cementing surface (50 µm Al 2 O 3 ) was significantly higher than the heat treated and the control group. Airborne particle abrasion followed by the heat treatment reduces the fracture strength of the specimen than that ofthe group treated only by the air abrasives. The fracture strength of a commercially available Ceramill (AMANNGIRRBACH) is greater than that of a Zirconia from ZR-White (UPCERA) variety.

To Evaluate Effect of Airborne Particle Abrasion using Different Abrasives Particles and Compare Two Commercial Available Zirconia on Flexural Strength on Heat Treatment

PubMed Central

Prasad, Hari A.; Pasha, Naveed; Hilal, Mohammed; Amarnath, G. S.; Kundapur, Vinaya; Anand, M; Singh, Sumeet

2017-01-01

control group (P<0.001); further AMANNGIRRBACH specimens gave a higher value compare to the UPCERA specimens. The study also revealed that the heat treatment of the specimens gave significant value (P<0.001) compared to the control group, but heat treatment following the air abrasion reduces the fracture strength of the sample than the air abraded group. Conclusion: Within the limitation of this study, it is concluded that, the in vitro fracture strength of Zirconia specimens treated with an airborne abrasion both on the veneering surface (50 µm silica coated Al2O3) and the cementing surface (50 µm Al2O3) was significantly higher than the heat treated and the control group. Airborne particle abrasion followed by the heat treatment reduces the fracture strength of the specimen than that ofthe group treated only by the air abrasives. The fracture strength of a commercially available Ceramill (AMANNGIRRBACH) is greater than that of a Zirconia from ZR-White (UPCERA) variety. PMID:28824346

The Effect of Pleural Abrasion on the Treatment of Primary Spontaneous Pneumothorax: A Systematic Review of Randomized Controlled Trials

PubMed Central

Ming, Mo-yu; Cai, Shuang-qi; Chen, Yi-Qiang

2015-01-01

Background Pleural abrasion has been widely used to control the recurrence of primary spontaneous pneumothorax (PSP). However, controversy still exists regarding the advantages and disadvantages of pleural abrasion compared with other interventions in preventing the recurrence of PSP. Methods The PubMed, Embase, and Cochrane Central Register of Controlled Trials databases were searched up to December 15, 2014 to identify randomized controlled trials (RCTs) that compared the effects of pleural abrasion with those of other interventions in the treatment of PSP. The study outcomes included the PSP recurrence rate and the occurrence rate of adverse effects. Results Mechanical pleural abrasion and apical pleurectomy after thoracoscopic stapled bullectomy exhibited similarly persistent postoperative air leak occurrence rates (p = 0.978) and 1-year PSP recurrence rates (p = 0.821), whereas pleural abrasion led to reduced residual chest pain and discomfort (p = 0.001) and a smaller rate of hemothorax (p = 0.036) than did apical pleurectomy. However, the addition of minocycline pleurodesis to pleural abrasion did not reduce the pneumothorax recurrence rate compared with apical pleurectomy (3.8% for both procedures) but was associated with fewer complications. There was no statistical difference in the pneumothorax recurrence rate between mechanical pleural abrasion and chemical pleurodesis with minocycline on either an intention-to-treat basis (4 of 42 versus 0 of 42, p = 0.12; Fisher exact test) or after exclusions (2 of 40 versus 0 of 42, p = 0.24; Fisher exact test). Pleural abrasion plus minocycline pleurodesis also did not reduce the pneumothorax recurrence rate compared with pleural abrasion alone (p = 0.055). Moreover, pleural abrasion plus minocycline pleurodesis was associated with more intense acute chest pain. The postoperative overall recurrence rate in patients who underwent staple line coverage with absorbable cellulose mesh and fibrin glue was similar to that

UPb ages of zircon rims: A new analytical method using the air-abrasion technique

USGS Publications Warehouse

Aleinikoff, J.N.; Winegarden, D.L.; Walter, M.

1990-01-01

We present a new technique for directly dating, by conventional techniques, the rims of zircons. Several circumstances, such as a xenocrystic or inherited component in igneous zircon and metamorphic overgrowths on igneous cores, can result in grains with physically distinct age components. Pneumatic abrasion has been previously shown by Krogh to remove overgrowths and damaged areas of zircon, leaving more resistant and isotopically less disturbed parts available for analysis. A new abrader design, which is capable of very gently grinding only tips and interfacial edges of even needle-like grains, permits easy collection of abraded material for dating. Five examples demonstrate the utility of the "dust-collecting" technique, including two studies that compare conventional, ion microprobe and abrader data. Common Pb may be strongly concentrated in the outermost zones of many zircons and this Pb is not easily removed by leaching (even in weak HF). Thus, the benefit of removing only the outermost zones (and avoiding mixing of age components) is somewhat compromised by the much higher common Pb contents which result in less precise age determinations. A very brief abrasion to remove the high common Pb zones prior to collection of material for dating is selected. ?? 1990.

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

Dentifrice fluoride and abrasivity interplay on artificial caries lesions.

PubMed

Nassar, Hani M; Lippert, Frank; Eckert, George J; Hara, Anderson T

2014-01-01

Incipient caries lesions on smooth surfaces may be subjected to toothbrushing, potentially leading to remineralization and/or abrasive wear. The interplay of dentifrice abrasivity and fluoride on this process is largely unknown and was investigated on three artificially created lesions with different mineral content/distribution. 120 bovine enamel specimens were randomly allocated to 12 groups (n = 10), resulting from the association of (1) lesion type [methylcellulose acid gel (MeC); carboxymethylcellulose solution (CMC); hydroxyethylcellulose gel (HEC)], (2) slurry abrasive level [low (REA 4/ RDA 69); high (REA 7/RDA 208)], and (3) fluoride concentration [0/275 ppm (14.5 mM) F as NaF]. After lesion creation, specimens were brushed in an automated brushing machine with the test slurries (50 strokes 2×/day). Specimens were kept in artificial saliva in between brushings and overnight. Enamel surface loss (SL) was determined by optical profilometry after lesion creation, 1, 3 and 5 days. Two enamel sections (from baseline and post-brushing areas) were obtained and analyzed microradiographically. Data were analyzed by analysis of variance and Tukey's tests (α = 5%). Brushing with high-abrasive slurry caused more SL than brushing with low-abrasive slurry. For MeC and CMC lesions, fluoride had a protective effect on SL from day 3 on. Furthermore, for MeC and CMC, there was a significant mineral gain in the remaining lesions except when brushed with high-abrasive slurries and 0 ppm F. For HEC, a significant mineral gain took place when low-abrasive slurry was used with fluoride. The tested lesions responded differently to the toothbrushing procedures. Both slurry fluoride content and abrasivity directly impacted SL and mineral gain of enamel caries lesions.

Analysis of Abrasive Blasting of DOP-26 Iridium Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohriner, Evan Keith; Zhang, Wei; Ulrich, George B

2012-01-01

The effects of abrasive blasting on the surface geometry and microstructure of DOP-26 iridium alloy (Ir-0.3% W-0.006% Th 0.005% Al) have been investigated. Abrasive blasting has been used to control emissivity of components operating at elevated temperature. The effects of abrasive blasting conditions on surface morphology were investigated both experimentally and by numerical modeling. The simplified model, based on finite element analysis of a single angular particle impacting on Ir alloy disk, calculates the surface deformation and residual strain distribution. The experimental results and modeling results both indicate that the surface geometry is not sensitive to the abrasive blast processmore » conditions of nozzle pressure and standoff distance considered in this study. On the other hand, the modeling results suggest that the angularity of the abrasive particle has an important role in determining surface geometry, which in turn, affects the emissivity. Abrasive blasting causes localized surface strains and localized recrystallization, but it does not affect grain size following extended exposure at elevated temperature. The dependence of emissivity of the DOP-26 alloy on mean surface slope follows a similar trend to that reported for pure iridium.« less

Solid Lubrication Fundamentals and Applications. Chapter 5; Abrasion: Plowing and Cutting

NASA Technical Reports Server (NTRS)

Miyoshi, Kazuhisa

2001-01-01

Chapter 5 discusses abrasion, a common wear phenomenon of great economic importance. It has been estimated that 50% of the wear encountered in industry is due to abrasion. Also, it is the mechanism involved in the finishing of many surfaces. Experiments are described to help in understanding the complex abrasion process and in predicting friction and wear behavior in plowing and/or cutting. These experimental modelings and measurements used a single spherical pin (asperity) and a single wedge pin (asperity). Other two-body and three-body abrasion studies used hard abrasive particles.

Corneal abrasion and alkali burn secondary to automobile air bag inflation

PubMed Central

Scarlett, Angela; Gee, Paul

2007-01-01

A 59‐year‐old woman self presented to the emergency department with a painful right eye following a motor vehicle accident. She had reduced visual acuity and the eye had an alkaline pH with complete corneal uptake of fluorescein. Diagnosis of corneal abrasion and alkali burn to her right eye secondary to inflation of a driver's automobile airbag was made. The eye was irrigated with normal saline. Such injuries, although rare, can easily be identified within the emergency department by the history of exposure, evidence of facial injuries or burns, and an alkaline pH in the inferior cul‐de‐sac of the eye. Early detection and management with ophthalmology review is therefore imperative to prevent irreversible visual impairment. PMID:17901284

An investigation into magnetic electrolytic abrasive turning

NASA Astrophysics Data System (ADS)

Mahdy, M. A. M.; Ismaeial, A. L.; Aly, F. F.

2013-07-01

The magnetic electrolytic abrasive turning (MEAT) process as a non-traditional machining is used to obtain surface finishing like mirror. MEAT provides one of the best alternatives for producing complex shapes with good finish in advanced materials used in aircraft and aerospace industries. The improvement of machining accuracy of MEAT continues to be a major challenge for modern industry. MEAT is a hybrid machining which combines two or more processes to remove material. The present research focuses on the development of precision electrochemical turning (ECT) under the effects of magnetic field and abrasives. The effect of magnetic flux density, electrochemical conditions and abrasive parameters on finishing efficiency and surface roughness are investigated. An empirical relationship is deduced.

Process Monitoring Evaluation and Implementation for the Wood Abrasive Machining Process

PubMed Central

Saloni, Daniel E.; Lemaster, Richard L.; Jackson, Steven D.

2010-01-01

Wood processing industries have continuously developed and improved technologies and processes to transform wood to obtain better final product quality and thus increase profits. Abrasive machining is one of the most important of these processes and therefore merits special attention and study. The objective of this work was to evaluate and demonstrate a process monitoring system for use in the abrasive machining of wood and wood based products. The system developed increases the life of the belt by detecting (using process monitoring sensors) and removing (by cleaning) the abrasive loading during the machining process. This study focused on abrasive belt machining processes and included substantial background work, which provided a solid base for understanding the behavior of the abrasive, and the different ways that the abrasive machining process can be monitored. In addition, the background research showed that abrasive belts can effectively be cleaned by the appropriate cleaning technique. The process monitoring system developed included acoustic emission sensors which tended to be sensitive to belt wear, as well as platen vibration, but not loading, and optical sensors which were sensitive to abrasive loading. PMID:22163477

The effect of air abrasion of metal implant abutments on the tensile bond strength of three luting agents used to cement implant superstructures: an in vitro study.

PubMed

Jugdev, Jasvinder; Borzabadi-Farahani, Ali; Lynch, Edward

2014-01-01

To assess the effect of airborne particle abrasion of metal implant abutments on tensile bond strength (TBS) of TempBond, Retrieve, and Premier implant cements. Specimens were designed to replicate a single metal implant crown cemented to both smooth and airborne particle-abraded Osteo-Ti implant abutments with zero degrees of taper. Twenty castings were fabricated and cemented to either a smooth surface abutment (SSA) or to an airborne particle-abraded abutment (AAA). TBS was measured with a 50-kg load and a crosshead speed of 0.5 cm/min in a universal testing machine. Each cement was tested 10 times on both abutment types. The mean TBS values (standard deviations, 95% confidence intervals) of SSAs for TempBond, Retrieve, and Premier cements were 115.89 N (26.44, 96.98-134.81), 134.43 N (36.95, 108.25-160.60), and 132.51 N (55.10, 93.09-171.93), respectively. The corresponding values for AAAs were 129.69 N (30.39, 107.95-151.43), 298.67 N (80.36, 241.19-356.16), and 361.17 N (133.23, 265.86-456.48), respectively. There was no significant difference in TBS among the dental cements when used with an SSA. Air abrasion of abutments did not increase the TBS of TempBond but significantly increased crown retention with Retrieve and Premier. For SSAs, all failures were adhesive on the abutment surface; for AAAs, mostly cohesive cement failures occurred. The retention of copings cemented with Retrieve or Premier to zero-degree-taper abutments was significantly increased after airborne particle abrasion of the abutments. However, this was not significant when TempBond was used. Airborne particle abrasion of abutments and the use of Retrieve or Premier can be recommended for nonretrievable prostheses. Although TempBond functioned similarly to the two other cements in SSAs, it is advisable to limit its use to provisional prostheses; its long-term performance needs to be assessed clinically.

Cosmetic Dentistry - Multiple Languages

MedlinePlus

... Here: Home → Multiple Languages → All Health Topics → Cosmetic Dentistry URL of this page: https://medlineplus.gov/languages/ ... W XYZ List of All Topics All Cosmetic Dentistry - Multiple Languages To use the sharing features on ...

Field evidence of two-phase abrasion process

NASA Astrophysics Data System (ADS)

Miller, K. L.; Szabo, T.; Jerolmack, D. J.; Domokos, G.

2013-12-01

The rounded shape of river rocks is clear evidence that abrasion due to bed load transport is a significant agent for mass loss. Its contribution to downstream fining, however, is typically assumed to be negligible - as diminution trends may be explained solely by size-selective transport. A recent theory has predicted that pebble abrasion occurs in two well separated phases: in Phase 1, an intially-polyhedral pebble rounds to the shape of an inscribed ellipsoid without any change in axis dimensions; in Phase II, axis dimensions are slowly reduced. Importantly, Phase I abrasion means that an initially-blocky pebble may lose up to half its mass without any apparent change in 'size', which is only measured as the length of a single pebble axis by most field researchers. We hypothesize that field studies have significantly underestimated the importance of abrasion because they do not quantify pebble shape, and we set out to demonstrate that two-phase abrasion occurs in a natural stream. Our study examines downstream trends in pebble size and shape along a 10-km stretch of the Rio Mameyes within the Luquillo Critical Zone observatory, where volcaniclastic cobbles and boulders are transported by bed load at slopes up to 10%. The upper reaches of the stream consist of alluviated bedrock valleys that preclude sediment storage and thus minimize size-selective transport, which allows us to isolate the effects of abrasion. The lower 5 km is an alluvial river in which size-selective transport becomes operative. We quantified the shape and size of thousands of pebbles along the profile using hand and image-based techniques. The data provide the first field validation of two-phase abrasion; in the bedrock reaches, pebbles clearly evolve toward ellipsoids without any significant change in axis dimensions (rounding), while in the lower reaches pebbles slowly reduce their axis dimensions with little or no change in roundness. Results also show that shape metrics determined from

Microwave sintering of sol-gel derived abrasive grain

DOEpatents

Plovnick, Ross; Celikkaya, Ahmet; Blake, Rodger D.

1997-01-01

A method is provided for making microwave-sintered, free flowing alpha alumina-based ceramic abrasive grain, under conditions effective to couple microwaves with calcined alpha alumina-based abrasive gain precursor and sinter it at a temperature of at least about 1150.degree. C.

Sports dentistry: A review

PubMed Central

Ramagoni, Naveen Kumar; Singamaneni, Vijaya Kumar; Rao, Saketh Rama; Karthikeyan, Jamini

2014-01-01

Dental trauma in sports is the major linking channel between sports and dentistry. Sports dentistry is the prevention of oral/facial athletic injuries and related oral diseases and manifestations. In children, sports activities were found to be responsible for 13% of overall oral trauma. It is emphasized that there is a great need for “Team Dentist” from high schools to professional teams. In this review, we discuss the relationship between sports and dentistry, and the importance of educating parents, teachers, and children in prevention of injuries related to the sports. PMID:25625070

Effects of air abrasion with alumina or glass beads on surface characteristics of CAD/CAM composite materials and the bond strength of resin cements

PubMed Central

Nobuaki, ARAO; Keiichi, YOSHIDA; Takashi, SAWASE

2015-01-01

ABSTRACT Objective The study aimed to evaluate effects of air abrasion with alumina or glass beads on bond strengths of resin cements to CAD/CAM composite materials. Material and Methods CAD/CAM composite block materials [Cerasmart (CS) and Block HC (BHC)] were pretreated as follows: (a) no treatment (None), (b) application of a ceramic primer (CP), (c) alumina-blasting at 0.2 MPa (AB), (d) AB followed by CP (AB+CP), and (e) glass-beads blasting at 0.4 MPa (GBB) followed by CP (GBB+CP). The composite specimens were bonded to resin composite disks using resin cements [G-CEM Cerasmart (GCCS) and ResiCem (RC)]. The bond strengths after 24 h (TC 0) and after thermal cycling (TC 10,000 at 4–60°C) were measured by shear tests. Three-way ANOVA and the Tukey compromise post hoc tests were used to analyze statistically significant differences between groups (α=0.05). Results For both CAD/CAM composite materials, the None group exhibited a significant decrease in bond strength after TC 10,000 (p<0.05). AB showed significantly higher bond strength after TC 10,000 than the None group, while CP did not (p<0.05). GBB exhibited smaller surface defects than did AB; however, their surface roughnesses were not significantly different (p>0.05). The AB+CP group showed a significantly higher bond strength after TC 10,000 than did the AB group for RC (p<0.05), but not for GCCS. The GBB+CP group showed the highest bond strength for both thermal cyclings (p<0.05). Conclusions Air abrasion with glass beads was more effective in increasing bond durability between the resin cements and CAD/CAM composite materials than was using an alumina powder and a CP. PMID:26814465

Green Dentistry, A Metamorphosis Towards an Eco-Friendly Dentistry: A Short Communication

PubMed Central

Sharma, Rachna; Yadav, Lalita; Satpute, Pranali; Sharma, Vandana

2014-01-01

Dentistry is most importantly and foremost a healing profession. In today’s world, it is very necessary to understand the importance of being eco-friendly in every facet of our lives, including dental practice which has a huge impact on the environment due to the large amount of metallic waste generated by various dental procedures along with excessive use of water and electricity, which specifically emphasis the thrust to move towards ‘Green dentistry’. Green dentistry is an innovative way of dental practice which is environment friendly and at the same time conserves money and time by reducing waste, conserving energy and decreasing pollution with the use of latest techniques and procedures. Green dentistry therefore, protects the environment and mankind from the hazards of rapid urbanisation in developing countries. The authors wish to emphasize the practice of eco-friendly, green dentistry in a developing country like India which needs to conserve resources and curb environmental pollution. PMID:25177666

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing.... The abrasive polish is applied to the teeth by a handpiece attachment (prophylaxis cup). (b...

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing.... The abrasive polish is applied to the teeth by a handpiece attachment (prophylaxis cup). (b...

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing.... The abrasive polish is applied to the teeth by a handpiece attachment (prophylaxis cup). (b...

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing.... The abrasive polish is applied to the teeth by a handpiece attachment (prophylaxis cup). (b...

21 CFR 872.6030 - Oral cavity abrasive polishing agent.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing.... The abrasive polish is applied to the teeth by a handpiece attachment (prophylaxis cup). (b...

Study of Abrasive Wear Volume Map for PTFE and PTFE Composites

NASA Astrophysics Data System (ADS)

Unal, H.; Sen, U.; Mimaroglu, A.

2007-11-01

The potential of this work is based on consideration of wear volume map for the evaluation of abrasive wear performance of polytetrafluoroethylene (PTFE) and PTFE composites. The fillers used in the composite are 25% bronze, 35% graphite and 17% glass fibre glass (GFR). The influence of filler materials, abrasion surface roughness and applied load values on abrasive wear performance of PTFE and PTFE composites were studied and evaluated. Experimental abrasive wear tests were carried out at atmospheric condition on pin-on-disc wear tribometer. Tests were performed under 4, 6, 8 and 10 N load values, travelling speed of 1 m/sec and abrasion surface roughness values of 5, 20 and 45 µm. Wear volume maps were obtained and the results showed that the lowest wear volume rate for PTFE is reached using GFR filler. Furthermore, the results also showed that the higher is the applied load and the roughness of the abrasion surface, the higher is the wear rate. Finally it is also concluded that abrasive wear process mechanism include ploughing and cutting mechanisms.

What about narrative dentistry?

PubMed

Vergnes, Jean-Noel; Apelian, Nareg; Bedos, Christophe

2015-06-01

Narrative medicine strives toward a humanized form of medicine in which empathy and the ability to listen are developed with the same emphasis as scientific rigor. We hypothesize that the adoption of narrative medicine in dentistry would be an excellent method to cultivate the philosophy behind the emerging clinical concept of patient-centered dentistry. Reading literary works, reflective writing, and creative writing would sensitize practitioners to the daily lives of people, human uniqueness, and alterity. Narrative dentistry could lead to more empathic and self-aware practices, and improve dental professionals' observational abilities by making them more perceptive and more attentive to image, metaphor, and meaning. The introduction of narrative dentistry would enrich the clinical clerkship of dentists by bringing the often-missing humanities to the dental professional, academic, and scientific environment. Copyright © 2015 American Dental Association. Published by Elsevier Inc. All rights reserved.

Investigation into the mechanisms of closed three-body abrasive wear

NASA Astrophysics Data System (ADS)

Dwyer-Joyce, R. S.; Sayles, R. S.; Ioannides, E.

1994-06-01

Contacting components frequently fail by abrasion caused by solid contaminants in the lubricant. This process can be classified as a closed three-body abrasive wear process. The mechanisms by which trapped particles cause material removal are not fully understood. This paper describes tests using model elastohydrodynamic contacts to study these mechanisms. An optical elastohydrodynamic lubrication rig has been used to study the deformation and fracture of ductile and brittle lubricant-borne debris. A ball-on-disk machine was used to study the behavior of the particles in partially sliding contacts. Small diamond particles were used as abrasives since these were thought not to break down in the contact; wear could then be directly related to particles of a known size. The particles were found to embed in the softer surface and to scratch the harder. The mass of material worn from the ball surface was approximately proportional to the particle sliding distance and abrasive concentration. Small particles tumbled through the contact, while larger particles ploughed. Mass loss was found to increase with abrasive particle size. Individual abrasion scratches have been measured and related to the abrading particle. A simple model of the abrasive process has been developed and compared with experimental data. The discrepancies are thought to be the result of the uncertainty about the entrainment of particles into the contact.

Friction and abrasion of elastomeric materials

NASA Technical Reports Server (NTRS)

Gent, A. N.

1975-01-01

An abrasion apparatus is described. Experimental measurements are reported for four representative elastomeric materials, including a typical high-quality tire tread material and a possible replacement material for aircraft tire treads based on transpolypentenamer (TPPR). Measurements are carried out at different levels of frictional work input, corresponding to different severities of wear, and at both ambient temperature and at 100 C. Results indicate the marked superiority in abrasion resistance of the material based on TPPR, especially at 100 C, in comparison with the other materials examined.

Heat sealable, flame and abrasion resistant coated fabric. [clothing and containers for space exploration

NASA Technical Reports Server (NTRS)

Tschirch, R. P.; Sidman, K. R. (Inventor)

1981-01-01

Flame retardant, abrasion resistant elastomeric compositions are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Coated fabrics employing such elastomeric compositions as coating film are flexible, lightweight, and air impermeable and can be made using heat or dielectric sealing procedures.

Control technology for crystalline silica exposures in construction: wet abrasive blasting.

PubMed

Golla, Vijay; Heitbrink, William

2004-03-01

This study was designed to document the effect that wet abrasive blasting has on reducing worker exposure to crystalline silica, which has been associated with silicosis and premature death. In this study, worker exposure to respirable crystalline silica was monitored during wet abrasive blasting on the exterior walls of a parking garage to remove surface concrete and expose the underlying aggregate. In this process a wet sand mix comprised of 80% dry sand and 20% water was used. Sampling and analysis revealed that the geometric mean respirable quartz concentration was 0.2 mg/m(3) for workers conducting abrasive blasting and 0.06 mg/m(3) for helpers. When abrasive blasting was conducted in areas that apparently had reduced natural ventilation, dust exposures appeared to increase. When compared with other published data, this case study suggests that wet abrasive blasting causes less exposure to crystalline silica than dry abrasive blasting.

Abrasive wear of ceramic wear protection at ambient and high temperatures

NASA Astrophysics Data System (ADS)

Varga, M.; Adam, K.; Tumma, M.; Alessio, K. O.

2017-05-01

Ceramic wear protection is often applied in abrasive conditions due to their excellent wear resistance. This is especially necessary in heavy industries conveying large amounts of raw materials, e.g. in steel industry. Some plants also require material transport at high temperatures and velocities, making the need of temperature stable and abrasion resistant wear protection necessary. Various types and wear behaviour of ceramic protection are known. Hence, the goal of this study is to identify the best suitable ceramic materials for abrasive conditions in harsh environments at temperatures up to 950°C and severe thermal gradients. Chamottes, known for their excellent thermal shock resistance are compared to high abrasion resistant ceramic wear tiles and a cost efficient cement-bounded hard compound. Testing was done under high-stress three-body abrasion regime with a modified ASTM G65 apparatus enabling for investigations up to ~950°C. Thereto heated abrasive is introduced into the wear track and also preheated ceramic samples were used and compared to ambient temperature experiments. Results indicate a significant temperature influence on chamottes and the hard compound. While the chamottes benefit from temperature increase, the cement-bounded hard compound showed its limitation at abrasive temperatures of 950°C. The high abrasion resistant wear tiles represented the materials with the best wear resistance and less temperature influence in the investigated range.

Interaction between attrition,abrasion and erosion in tooth wear.

PubMed

Addy, M; Shellis, R P

2006-01-01

Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence seems insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear through formation of pellicle and by remineralisation but cannot prevent it.

Atmospheric particulate emissions from dry abrasive blasting using coal slag.

PubMed

Kura, Bhaskar; Kambham, Kalpalatha; Sangameswaran, Sivaramakrishnan; Potana, Sandhya

2006-08-01

Coal slag is one of the widely used abrasives in dry abrasive blasting. Atmospheric emissions from this process include particulate matter (PM) and heavy metals, such as chromium, lead, manganese, nickel. Quantities and characteristics of PM emissions depend on abrasive characteristics and process parameters. Emission factors are key inputs to estimate emissions. Experiments were conducted to study the effect of blast pressure, abrasive feed rate, and initial surface contamination on total PM (TPM) emission factors for coal slag. Rusted and painted mild steel surfaces were used as base plates. Blasting was carried out in an enclosed chamber, and PM was collected from an exhaust duct using U.S. Environment Protection Agency source sampling methods for stationary sources. Results showed that there is significant effect of blast pressure, feed rate, and surface contamination on TPM emissions. Mathematical equations were developed to estimate emission factors in terms of mass of emissions per unit mass of abrasive used, as well as mass of emissions per unit of surface area cleaned. These equations will help industries in estimating PM emissions based on blast pressure and abrasive feed rate. In addition, emissions can be reduced by choosing optimum operating conditions.

Method for forming an abrasive surface on a tool

DOEpatents

Seals, Roland D.; White, Rickey L.; Swindeman, Catherine J.; Kahl, W. Keith

1999-01-01

A method for fabricating a tool used in cutting, grinding and machining operations, is provided. The method is used to deposit a mixture comprising an abrasive material and a bonding material on a tool surface. The materials are propelled toward the receiving surface of the tool substrate using a thermal spray process. The thermal spray process melts the bonding material portion of the mixture, but not the abrasive material. Upon impacting the tool surface, the mixture or composition solidifies to form a hard abrasive tool coating.

Dentistry proteomics: from laboratory development to clinical practice.

PubMed

Rezende, Taia M B; Lima, Stella M F; Petriz, Bernardo A; Silva, Osmar N; Freire, Mirna S; Franco, Octávio L

2013-12-01

Despite all the dental information acquired over centuries and the importance of proteome research, the cross-link between these two areas only emerged around mid-nineties. Proteomic tools can help dentistry in the identification of risk factors, early diagnosis, prevention, and systematic control that will promote the evolution of treatment in all dentistry specialties. This review mainly focuses on the evolution of dentistry in different specialties based on proteomic research and how these tools can improve knowledge in dentistry. The subjects covered are an overview of proteomics in dentistry, specific information on different fields in dentistry (dental structure, restorative dentistry, endodontics, periodontics, oral pathology, oral surgery, and orthodontics) and future directions. There are many new proteomic technologies that have never been used in dentistry studies and some dentistry areas that have never been explored by proteomic tools. It is expected that a greater integration of these areas will help to understand what is still unknown in oral health and disease. Copyright © 2013 Wiley Periodicals, Inc.

Ethical advertising in dentistry.

PubMed

Graskemper, Joseph P

2009-01-01

Advertising in dentistry has steadily increased since the 1970s to become a leading choice of many dentists to promote their practices. The manner in which advertising progresses within the profession affects all dentists and how patients perceive dentistry as a profession. This paper presents ethical concepts that should be followed when dentists are pursuing practice promotion through advertising. It also raises questions that, hopefully, will increase attention and discussion on dental advertising. The paper concludes that ethical advertising is easily achieved by promoting patient education while not placing the dentist's self-interests ahead of the patient's. With this approach, dentistry may continue to be one of the most trusted professions.

Modeling of Micro Deval abrasion loss based on some rock properties

NASA Astrophysics Data System (ADS)

Capik, Mehmet; Yilmaz, Ali Osman

2017-10-01

Aggregate is one of the most widely used construction material. The quality of the aggregate is determined using some testing methods. Among these methods, the Micro Deval Abrasion Loss (MDAL) test is commonly used for the determination of the quality and the abrasion resistance of aggregate. The main objective of this study is to develop models for the prediction of MDAL from rock properties, including uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness, apparent porosity, void ratio Cerchar abrasivity index and Bohme abrasion test are examined. Additionally, the MDAL is modeled using simple regression analysis and multiple linear regression analysis based on the rock properties. The study shows that the MDAL decreases with the increase of uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness and Cerchar abrasivity index. It is also concluded that the MDAL increases with the increase of apparent porosity, void ratio and Bohme abrasion test. The modeling results show that the models based on Bohme abrasion test and L type Schmidt rebound hardness give the better forecasting performances for the MDAL. More models, including the uniaxial compressive strength, the apparent porosity and Cerchar abrasivity index, are developed for the rapid estimation of the MDAL of the rocks. The developed models were verified by statistical tests. Additionally, it can be stated that the proposed models can be used as a forecasting for aggregate quality.

Effect of nanofillers' size on surface properties after toothbrush abrasion.

PubMed

Cavalcante, Larissa M; Masouras, Konstantinos; Watts, David C; Pimenta, Luiz A; Silikas, Nick

2009-02-01

To investigate the effect of filler-particle size of experimental and commercial resin composites, undergoing toothbrush abrasion, on three surface properties: surface roughness (SR), surface gloss (G) and color stability (CS). Four model (Ivoclar/Vivadent) and one commercial resin composite (Tokuyama) with varying filler-size from 100-1000 nm were examined. Six discs (10 mm x 2 mm) from each product were prepared and mechanically polished. The samples were then submitted to 20,000 brushing strokes in a toothbrush abrasion machine. SR parameters (Ra, Rt and RSm), G, and CS were measured before and after toothbrush abrasion. Changes in SR and G were analyzed by 2-way ANOVA, with Bonferroni post hoc test. CS values were submitted to one-way ANOVA and Bonferroni post hoc test (alpha=0.05). Initial G values ranged between 73-87 gloss units (GU) and were reduced after toothbrush abrasion to a range of 8-64 GU. Toothbrush abrasion resulted in significant modifications in SR and G amongst the materials tested, attributed to filler sizes. There was statistically significant difference in color (delta E* ranged from 0.38-0.88). Filler size did not affect color stability. Toothbrush abrasion resulted in rougher and matte surfaces for all materials tested. Although the individual differences in surface roughness among filler sizes were not always significant, the correlation showed a trend that larger filler sizes resulted in higher surface roughness after abrasion for the SR parameters Ra and Rt (r = 0.95; r = 0.93, respectively). RSm showed an increase after toothbrush abrasion for all resin composites, however no significant correlation was detected (r = 0.21).There was a significant correlation between G and Ra ratios (r = - 0.95).

Mars Pathfinder: The Wheel Abrasion Experiment

NASA Technical Reports Server (NTRS)

1996-01-01

NASA Lewis Research Center's Wheel Abrasion Experiment (WAE) will measure the amount of wear on wheel surfaces of the Mars Pathfinder rover. WAE uses thin films of Al, Ni, and Pt (ranging in thickness from 200 to 1000 angstroms) deposited on black, anodized Al strips attached to the rover wheel. As the wheel moves across the martian surface, changes in film reflectivity will be monitored by reflected sunlight. These changes, measured as output from a special photodetector mounted on the rover chassis, will be due to abrasion of the metal films by martian surface sand, dust, and clay.

Ergonomics and dentistry.

PubMed

Murphy, D C

1997-01-01

Since 1992 the Occupational Safety and Health Administration (OSHA) has been preparing Federal legislation concerned with ergonomic hazards in at-risk workplaces. Although multifactorial in nature, there is sufficient evidence in the scientific literature to document an association between the practice of dentistry and a variety of musculoskeletal disorders. There are preventive strategies already known and available to us. Should dentistry be considered an at-risk profession and be required to comply with the forthcoming standard, or is self-monitoring sufficient?

Rock Abrasion Tool Exhibits the Deep Red Pigment of Mars

NASA Technical Reports Server (NTRS)

2006-01-01

During recent soil-brushing experiments, the rock abrasion tool on NASA's Mars Exploration Rover Spirit became covered with dust, as shown here. An abundance of iron oxide minerals in the dust gave the device a reddish-brown veneer. Investigators were using the rock abrasion tool to uncover successive layers of soil in an attempt to reveal near-surface stratigraphy. Afterward, remnant dirt clods were visible on both the bit and the brush of the tool. Designers of the rock abrasion tool at Honeybee Robotics and engineers at the Jet Propulsion Laboratory developed a plan to run the brush on the rock abrasion tool in reverse to dislodge the dirt and return the tool to normal operation. Subsequent communications with the rover revealed that the procedure is working and the rock abrasion tool remains healthy.

Spirit acquired this approximately true-color image with the panoramic camera on the rover's 893rd sol, or Martian day (July 8, 2006). The image combines exposures taken through three of the camera's filters, centered on wavelengths of 750 nanometers, 530 nanometers, and 430 nanometers.

Dosimetry in dentistry.

PubMed

Asha, M L; Chatterjee, Ingita; Patil, Preeti; Naveen, S

2015-01-01

The purpose of this paper was to review various dosimeters used in dentistry and the cumulative results of various studies done with various dosimeters. Several relevant PubMed indexed articles from 1999 to 2013 were electronically searched by typing "dosimeters", "dosimeters in dentistry", "properties of dosimeters", "thermoluminescent and optically stimulated dosimeters", "recent advancements in dosimetry in dentistry." The searches were limited to articles in English to prepare a concise review on dental dosimetry. Titles and abstracts were screened, and articles that fulfilled the criteria of use of dosimeters in dental applications were selected for a full-text reading. Article was divided into four groups: (1) Biological effects of radiation, (2) properties of dosimeters, (3) types of dosimeters and (4) results of various studies using different dosimeters. The present review on dosimetry based on various studies done with dosimeters revealed that, with the advent of radiographic technique the effective dose delivered is low. Therefore, selection of radiological technique plays an important role in dental dose delivery.

Brexit and dentistry.

PubMed

Sinclair, E; Stagnell, S; Shah, S

2016-05-27

On 23 June 2016, eligible UK voters will be asked to decide whether to vote in the EU referendum. The EU impacts on our daily lives in more ways than many people realise. Dentistry is affected by EU legislation. Examples include the movement of dental professionals, the import of dental equipment and materials, as well as health and safety legislation. Many more EU dentists and DCPs come to the UK to work than vice versa. These numbers have increased markedly since 2004. The result of the vote may affect how dentistry operates in the UK in future years. In addition, a vote to stay would not necessarily prevent change. There are attempts underway to increase the ease by which professionals can work in other member states, especially on a temporary basis. This too is likely affect dentistry at some point. Workforce planners and policy makers should factor in the impact of the EU in future dental policy.

[Research Progress on Forensic Dentistry].

PubMed

Liu, F; Dang, Y H

2017-04-01

Forensic dentistry is an interdiscipline of forensic medicine and stomatology, which provides legal information by collecting, testing and assessing the dental evidence scientifically. In this review, the present application of forensic dentistry has been described, such as the estimation of age, sex, species, occupation and living habit, as well as the identification of individual, domestic violence or abuse, which aims to enrich and improve forensic dentistry for making it be more useful in forensic medicine even in juridical practice. Copyright© by the Editorial Department of Journal of Forensic Medicine.

The erosion and abrasion-inhibiting effect of TiF(4) and NaF varnishes and solutions on enamel in vitro.

PubMed

Levy, Flávia Mauad; Magalhães, Ana Carolina; Gomes, Marina Franciscon; Comar, Livia Picchi; Rios, Daniela; Buzalaf, Marília Afonso Rabelo

2012-01-01

OBJECTIVE. Previous in vitro study has shown that TiF(4) varnish might reduce enamel erosion. No data regarding the effect of this experimental varnish on enamel erosion plus abrasion, however, are available so far. Thus, this in vitro study aimed to analyse the effect of TiF(4) compared with NaF varnishes and solutions, to protect against enamel erosion with or without abrasion. METHODS. Enamel specimens were pre-treated with experimental-TiF(4) (2.45% F), experimental-NaF (2.45% F), NaF-Duraphat (2.26% F), and placebo varnishes; NaF (2.26% F) and TiF(4) (2.45% F) solutions. Controls remained untreated. The erosive challenge was performed using a soft drink (pH 2.6) 4 × 90 s/day (ERO) and the toothbrushing abrasion (ERO+ABR) 2 × 10 s/day, for 5 days. Between the challenges, the specimens were exposed to artificial saliva. Enamel loss was measured profilometrically (μm). RESULTS. Kruskal-Wallis/Dunn tests showed that all fluoridated varnishes (TiF(4) -ERO:0.53 ± 0.20, ERO+ABR:0.65 ± 0.19/NaF-ERO:0.94 ± 0.18, ERO+ABR:1.74 ± 0.37/Duraphat-ERO:1.00 ± 0.37, ERO+ABR:1.72 ± 0.58) were able to significantly reduce enamel loss when compared with placebo varnish (ERO:3.45 ± 0.41/ERO+ABR:3.20 ± 0.66) (P < 0.0001). Placebo varnish, control (ERO:2.68 ± 0.53/ERO+ABR:3.01 ± 0.34), and fluoridated (NaF-ERO:2.84 ± 0.09/ERO+ABR:2.40 ± 0.21/TiF(4) -ERO:3.55 ± 0.59/ERO+ABR:4.10 ± 0.38) solutions did not significantly differ from each other. CONCLUSION. Based on the results, it can be concluded that the TiF(4) varnish seems to be a promising treatment to reduce enamel loss under mild erosive and abrasive conditions in vitro. © 2011 The Authors. International Journal of Paediatric Dentistry © 2011 BSPD, IAPD and Blackwell Publishing Ltd.

Wear resistance and mechanisms of composite hardfacings at abrasive impact erosion wear

NASA Astrophysics Data System (ADS)

Surzhenkov, A.; Viljus, M.; Simson, T.; Tarbe, R.; Saarna, M.; Casesnoves, F.

2017-05-01

Tungsten carbide based hardmetal containing sprayed and melted composite hardfacings are prospective for protection against abrasive wear. For selection of abrasive wear resistant hardfacings under intensive impact wear conditions, both mechanical properties (hardness, fracture toughness, etc.) and abrasive wear conditions (type of abrasive, impact velocity, etc.) should be considered. This study focuses on the wear (wear rate and mechanisms) of thick metal-matrix composite hardfacings with hardmetal (WC-Co) reinforcement produced by powder metallurgy technology. The influence of the hardmetal reinforcement type on the wear resistance at different abrasive impact erosion wear (AIEW) conditions was studied. An optimal reinforcement for various wear conditions is described. Based on wear mechanism studies, a mathematical model for wear prediction was drafted.

The evidence-based dentistry initiative at Baylor College of Dentistry.

PubMed

Jones, Daniel L; Hinton, Robert J; Dechow, Paul C; Abdellatif, Hoda; McCann, Ann L; Schneiderman, Emet D; D'Souza, Rena

2011-02-01

This report describes the impact of an R25 Oral Health Research Education Grant awarded to the Texas A&M Health Science Center-Baylor College of Dentistry (BCD) to promote the application of basic and clinical research findings to clinical training and encourage students to pursue careers in oral health research. At Baylor, the R25 grant supports a multi-pronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all 4 years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent "EBD culture" characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty who can model the importance of evidence-based practice is of paramount importance for the future of dentistry.

Valve for abrasive material

DOEpatents

Gardner, Harold S.

1982-01-01

A ball valve assembly for controlling the flow of abrasive particulates including an enlarged section at the bore inlet and an enlarged section at the bore outlet. A refractory ceramic annular deflector is positioned in each of the enlarged sections, substantially extending the useful life of the valve.

Mangrove Cultivation For Dealing With Coastal Abrasion Case Study Of Karangsong

NASA Astrophysics Data System (ADS)

Fatimatuzzahroh, Feti; Hadi, Sudharto P.; Purnaweni, Hartuti

2018-02-01

Coastal abrasion is consequence from destructive waves and sea current. One of cause is human intervention. The effort to solve of abrasion is by mangrove cultivation. Mangroves are halophyte plant that can restrain the sea wave. Mangrove cultivation required participation community that give awareness the importance of mangrove in coastal sustainability. Mangroves in coastal Karangsong, Indramayu west java, in 2007 was through abrasion approximately 127.30 ha. Mangrove cultivation in Karangsong has been replanting since 1998 to 2003, but there was no maintenance and management. In 2007 until 2015 Karangsong replanting mangroves and has been succeed. Karangsong became the center of mangrove study for west java area in 2015. This achievement is result of cooperation between community, NGO, and local government. In addition, this effort made not only overcome the abrasion problem but also give community awareness about the importance of mangrove cultivation in preventing coastal abrasion throughout community development. This paper reviews abrasion in Karangsong and the impact for local community and empowerment in mangrove cultivation. To achieve the success mangrove cultivation required community development approach from planning process, planting, maintenance and management.

7 CFR 3201.66 - Cuts, burns, and abrasions ointments.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 15 2014-01-01 2014-01-01 false Cuts, burns, and abrasions ointments. 3201.66 Section... PROCUREMENT Designated Items § 3201.66 Cuts, burns, and abrasions ointments. (a) Definition. Products designed..., in accordance with this part, will give a procurement preference for qualifying biobased cuts, burns...

7 CFR 3201.66 - Cuts, burns, and abrasions ointments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 15 2013-01-01 2013-01-01 false Cuts, burns, and abrasions ointments. 3201.66 Section... PROCUREMENT Designated Items § 3201.66 Cuts, burns, and abrasions ointments. (a) Definition. Products designed..., in accordance with this part, will give a procurement preference for qualifying biobased cuts, burns...

7 CFR 3201.66 - Cuts, burns, and abrasions ointments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 15 2012-01-01 2012-01-01 false Cuts, burns, and abrasions ointments. 3201.66 Section... PROCUREMENT Designated Items § 3201.66 Cuts, burns, and abrasions ointments. (a) Definition. Products designed..., in accordance with this part, will give a procurement preference for qualifying biobased cuts, burns...

Optical-model abrasion cross sections for high-energy heavy ions

NASA Technical Reports Server (NTRS)

Townsend, L. W.

1981-01-01

Within the context of eikonal scattering theory, a generalized optical model potential approximation to the nucleus-nucleus multiple scattering series is used in an abrasion-ablation collision model to predict abrasion cross sections for relativistic projectile heavy ions. Unlike the optical limit of Glauber theory, which cannot be used for very light nuclei, the abrasion formalism is valid for any projectile target combination at any incident kinetic energy for which eikonal scattering theory can be utilized. Results are compared with experimental results and predictions from Glauber theory.

Plasma in dentistry: a review of basic concepts and applications in dentistry.

PubMed

Kim, Jae-Hoon; Lee, Mi-Ae; Han, Geum-Jun; Cho, Byeong-Hoon

2014-01-01

Plasma-related technologies are essential in modern industries. Recently, plasma has attracted increased attention in the biomedical field. This paper provides a basic knowledge of plasma and a narrative review of plasma applications in dentistry. To review plasma applications in dentistry, an electronic search in PubMed, SCOPUS and Google scholar up to December 2012 was done. This was followed by extensive hand searching using reference lists from relevant articles. There have been attempts to apply plasma technology in various fields of dentistry including surface modifications of dental implants, adhesion, caries treatment, endodontic treatment and tooth bleaching. Although many studies were in early stages, the potential value of plasma for dental applications has been demonstrated. To enlarge the scope of plasma applications and put relevant research to practical use, interdisciplinary research with participation of dental professionals is required.

A Review on Parametric Analysis of Magnetic Abrasive Machining Process

NASA Astrophysics Data System (ADS)

Khattri, Krishna; Choudhary, Gulshan; Bhuyan, B. K.; Selokar, Ashish

2018-03-01

The magnetic abrasive machining (MAM) process is a highly developed unconventional machining process. It is frequently used in manufacturing industries for nanometer range surface finishing of workpiece with the help of Magnetic abrasive particles (MAPs) and magnetic force applied in the machining zone. It is precise and faster than conventional methods and able to produce defect free finished components. This paper provides a comprehensive review on the recent advancement of MAM process carried out by different researcher till date. The effect of different input parameters such as rotational speed of electromagnet, voltage, magnetic flux density, abrasive particles size and working gap on the performances of Material Removal Rate (MRR) and surface roughness (Ra) have been discussed. On the basis of review, it is observed that the rotational speed of electromagnet, voltage and mesh size of abrasive particles have significant impact on MAM process.

[The elementary discussion on digital implant dentistry].

PubMed

Su, Y C

2016-04-09

It is a digital age today. Exposed to all kinds of digital products in many fields. Certainly, implant dentistry is not exception. Digitalization could improve the outcomes and could decrease the complications of implant dentistry. This paper introduces the concepts, definitions, advantages, disadvantages, limitations and errors of digital implant dentistry.

Aliasing Signal Separation of Superimposed Abrasive Debris Based on Degenerate Unmixing Estimation Technique.

PubMed

Li, Tongyang; Wang, Shaoping; Zio, Enrico; Shi, Jian; Hong, Wei

2018-03-15

Leakage is the most important failure mode in aircraft hydraulic systems caused by wear and tear between friction pairs of components. The accurate detection of abrasive debris can reveal the wear condition and predict a system's lifespan. The radial magnetic field (RMF)-based debris detection method provides an online solution for monitoring the wear condition intuitively, which potentially enables a more accurate diagnosis and prognosis on the aviation hydraulic system's ongoing failures. To address the serious mixing of pipe abrasive debris, this paper focuses on the superimposed abrasive debris separation of an RMF abrasive sensor based on the degenerate unmixing estimation technique. Through accurately separating and calculating the morphology and amount of the abrasive debris, the RMF-based abrasive sensor can provide the system with wear trend and sizes estimation of the wear particles. A well-designed experiment was conducted and the result shows that the proposed method can effectively separate the mixed debris and give an accurate count of the debris based on RMF abrasive sensor detection.

Aliasing Signal Separation of Superimposed Abrasive Debris Based on Degenerate Unmixing Estimation Technique

PubMed Central

Li, Tongyang; Wang, Shaoping; Zio, Enrico; Shi, Jian; Hong, Wei

2018-01-01

Leakage is the most important failure mode in aircraft hydraulic systems caused by wear and tear between friction pairs of components. The accurate detection of abrasive debris can reveal the wear condition and predict a system’s lifespan. The radial magnetic field (RMF)-based debris detection method provides an online solution for monitoring the wear condition intuitively, which potentially enables a more accurate diagnosis and prognosis on the aviation hydraulic system’s ongoing failures. To address the serious mixing of pipe abrasive debris, this paper focuses on the superimposed abrasive debris separation of an RMF abrasive sensor based on the degenerate unmixing estimation technique. Through accurately separating and calculating the morphology and amount of the abrasive debris, the RMF-based abrasive sensor can provide the system with wear trend and sizes estimation of the wear particles. A well-designed experiment was conducted and the result shows that the proposed method can effectively separate the mixed debris and give an accurate count of the debris based on RMF abrasive sensor detection. PMID:29543733

Abrasion Plus Local Fibrin Sealant Instillation Produces Pleurodesis Similar to Pleurectomy in Rabbits.

PubMed

Marchi, Evaldo; de Carvalho, Marcus V H; Ventureli, Tiago R; Fruchi, Andre J; Lazaro, Ariane; do Carmo, Deborah C; Barreto, Thayssa Y A S; Dias, Bruno V B; Acencio, Milena M P; Teixeira, Lisete R; Light, Richard W

2016-09-01

Pleurodesis performed either by pleurectomy or pleural abrasion is recommended in the approach to primary spontaneous pneumothorax to avoid recurrence. However, the efficacy of parietal pleural abrasion in producing pleurodesis is questioned. This study aims to determine the efficacy of apical abrasion alone, abrasion plus fibrin sealant application, and pleurectomy in producing pleurodesis in rabbits. Rabbits were subjected to video-assisted thoracic surgery alone (control) or to video-assisted thoracic surgery with apical gauze abrasion, abrasion plus fibrin sealant instillation, or apical pleurectomy. Blood samples were collected preoperatively and 48 h and 28 days postoperatively to measure total leukocytes (white blood cell count), neutrophil counts, and serum interleukin (IL)-8 levels. After 28 days the animals were sacrificed for macroscopic evaluation of the degree of apical pleurodesis and microscopic evaluation of local pleural fibrosis and collagen deposition. White blood cell and neutrophil counts were similar in all groups, whereas the serum IL-8 level peaked at 48 h in all groups and decreased after 28 days, except in the pleurectomy group. After 28 days the abrasion plus fibrin sealant and pleurectomy groups had significantly more pleural adhesions, pleural fibrosis, and collagen deposition than the abrasion alone group, mainly due to thick mature fibers. Abrasion with local fibrin sealant instillation is as effective as pleurectomy in producing pleurodesis in rabbits. Apical pleurectomy elicits a more persistent elevation of serum IL-8 levels than apical abrasion alone or abrasion plus fibrin adhesive instillation. Copyright © 2016 American College of Chest Physicians. Published by Elsevier Inc. All rights reserved.

[Brushing abrasion of the enamel surface after erosion].

PubMed

Lipei, Chen; Xiangke, Ci; Xiaoyan, Ou

2017-08-01

Objective A study was conducted to compare the effect of different enamel remineralization periods after erosion on the depth of brushing abrasion. Methods Ten volunteers were selected for a 4-day experiment. A total of 60 enamels were randomly assigned into six groups (A-F) and placed in intraoral palatal devices. On the first day, the palatal devices were placed in oral cavity (24 h) . On the following three days, brushing experiments were performed extraorally, two times per day. The specific experimental method of brushing follows these next steps. First, the group F specimens were covered with a film of wax, and then acid etched for 2 min. Subsequently, the film of wax was detached. The groups from A to D were brushed after remineralization at the following time intervals: group A, 0 min; group B, 20 min; group C, 40 min; group D, 60 min. Erosion and remineralization were performed on group E, but without brushing. Remineralization was performed on group F, but without acid etching and brushing. The depth of enamel abrasion was determined by a mechanical profilometer. The surface morphology of the enamel blocks was observed using a scanning electron microscope. Results 1) The depth of abrasion was different in varied enamel remineralization time after acid etching. The statistical significant differences between groups were as follows. 2) When the time of enamel remineralization after acid etching was short, the surface depression in the electron microscope was deep, and the surface morphology was rough. Conclusion Brushing immediately after acid etching would cause much serious abrasion to the enamel surface. Brushing after 60 min can effectively reduce the abrasion of acid etching enamel.

Shoe heel abrasion and its possible biomechanical cause: a transversal study with infantry recruits.

PubMed

Baumfeld, Daniel; Raduan, Fernando C; Macedo, Benjamim; Silva, Thiago Alexandre Alves; Baumfeld, Tiago; Favato, Danilo Fabrino; de Andrade, Marco Antonio Percope; Nery, Caio

2015-11-19

Excessive shoe heel abrasion is of concern to patients and shoe manufacturers, but little scientific information is available about this feature and its possible causes. The purpose of this study was to relate this phenomenon with biomechanical factors that could predispose to shoe heel abrasion. Ninety-seven recruits (median age 25) were enrolled in this study. Shoe abrasion was assessed manually with a metric plastic tape on the posterior part of the heel that comes in contact with the ground. The number of sprains, foot alignment, and calf muscle shortening (Silfverskiold test) was also assessed in order to relate it with shoe heel abrasion. After using our exclusion criteria, 86 recruits and 172 were considered for this study. The most common abrasion site was the lateral portion of the heel surface (50 %). Forty-four percent of the participants had neutral hind-foot alignment and 39 % had valgus alignment. Twenty-six (30 %) patients have had previous ankle or foot sprains. Neutral foot was related with less calf muscle shortening. On the other hand, valgus hind-foot alignment was more associated with Achilles shortening (p < 0.05). Patients with neutral alignment were associated with more uniform shoe heel abrasion and varus feet were associated with more central and lateral abrasion (p < 0.05). The pattern of shoe heel abrasion was not statistically related with calf muscle shortening nor with number of sprains. This study was able to correlate shoe heel abrasion with biomechanical causes (neutral alignment-uniform abrasion/varus alignment-central and lateral abrasion). More effort has to be done to continue evaluating outsole abrasion with its possible biomechanical cause in order to predict and treat possible associated injuries.

Curriculum Guidelines for Operative Dentistry.

ERIC Educational Resources Information Center

Journal of Dental Education, 1984

1984-01-01

The American Association of Dental Schools' guidelines for operative dentistry curricula include an overview of the scope and objectives of operative dentistry, notes on the interrelationship of the discipline and the total curriculum, and an outline of primary educational goals, core content, specific behavioral objectives, sequencing, faculty,…

Eye Injuries from Air Bags with Seamless Module Covers

PubMed Central

Duma, Stefan M.; Crandall, Jeff R.

1999-01-01

Air bag deployment through a seamless module cover may release foam particles at high velocities that could result in eye injuries. This paper presents the results of twenty-one (n = 21) tests in which foam particles, similar to those observed from air bag deployments, were impacted onto porcine eyes. A pneumatic cannon was designed to propel the foam disks at speeds representative of actual foam particle velocities as observed in prototype air bag deployments. Five foam types, which varied in density and stiffness, were used. All tests were recorded with high speed video (1000 fps). The mass of the impacting particles varied from 0.155 g to 0.653 g with velocities from 18 m/s to 87.6 m/s. Injury analysis was performed using three techniques: fluorescein dye to reveal corneal abrasions, ophthalmic ultrasound to determine lens displacements and retinal detachments, and necropsy to examine tissue damage. As seen in case reports of air bag induced eye injuries, corneal abrasions were the most recorded injuries in the porcine eye impact tests. A logistic regression analysis demonstrated that the combination of mass and velocity in the form of kinetic energy was the most significant contributor to injury (p = 0.0023). An injury risk curve was generated based on kinetic energy which gave a 50% risk of corneal abrasion at 0.183 J. Over the range of materials used, the foam type was a poor contributor to the model (p = 0.45). The injury risk function presented for the kinetic energy of the particles offers a design guide to minimize corneal abrasions, if the production of foam particles during air bag deployment is unavoidable.

Prevalence of molar-incisor hypomineralization (MIH) in children seeking dental care at the Schools of Dentistry of the University of Buenos Aires (Argentina) and University of la Republica (Uruguay).

PubMed

Biondi, Ana M; López Jordi, María del C; Cortese, Silvina G; Alvarez, Licet; Salveraglio, Inés; Ortolani, Andrea M

2012-01-01

The objectives of this study are to compare the prevalence of MIH in children seeking dental care spontaneously at the Department of Comprehensive Children's Dentistry of the University of Buenos Aires (UBA) and Department of Pediatric Dentistry of the University of La República (UdelaR) and to analyze the distribution according to year of birth, sex, age, number of affected teeth and maximum degree of severity in molars and incisors. During 2010, nine pediatric dentists from both schools (Kappa = 0.94) assessed all children born between 1993 and 2003 whose 4 first molars and 8 permanent incisors had erupted. Specially designed charts were used to record sex, year of birth, institution, presence of MIH, number of affected incisors and molars and maximum degree of severity for each tooth. Two groups were formed: UBA: A (n = 512) and UdelaR: B (n = 463). 975 children (11.6 +/- 2.67 years) were evaluated. The prevalence of MIH in the total sample was 6.56%, without significant differences between A and B (p = 0.76). There was no significant difference between groups regarding age (p = 0. 95) or sex (p = 0.30). A significant increase was found in both institutions according to year of birth during the study period. (A: p = 0.0017) B: p = 0. 0058). The results of this study show a similar prevalence of MIH among patients seeking dental care at the Schools of Dentistry of the University of Buenos Aires (Argentina) and University of la República (Uruguay). No significant difference was found comparing the distribution by sex, affected teeth or severity of each tooth. A highly significant positive correlation was found regarding the year of birth. The relevance of MIH as an emerging pathology requires studies on larger samples covering the entire countries.

Evaluation of abrasion resistance of pipe and pipe lining materials.

DOT National Transportation Integrated Search

2007-09-01

This project summarizes an evaluation of pipe material resistance to abrasion over a 5-year period (2001-2006) at a site known to be abrasive. : The key focus of the project was to gather more information to compare against existing guidance to desig...

Veterinary dentistry: a clinician's viewpoint.

PubMed

Baxter, Colin

2013-06-01

This is a clinician's view of the current state of veterinary dentistry at the level of the general practitioner across the different species. An indication of the work done and the hazards commonly encountered are covered. To increase awareness within the dental profession of the current state of veterinary dentistry.

The interactions between attrition, abrasion and erosion in tooth wear.

PubMed

Shellis, R Peter; Addy, Martin

2014-01-01

Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Knowledge of these tooth wear processes and their interactions is reviewed. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence is insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear, especially through formation of pellicle, but cannot prevent it. © 2014 S. Karger AG, Basel.

Efficiency improvement of dentistry clinics: introducing an intervening package for dentistry clinics, isfahan, iran.

PubMed

Alaghemandan, Hamed; Yarmohammadian, Mohammad H; Khorasani, Elahe; Rezaee, Sobhan

2014-02-01

In Isfahan, the second metropolitan in Iran, there are 1448 dentistry treatment centers that most of them are inefficient. Today, efficiency is the most important issue in health care centers as well as dentistry clinics. The goal of this research is to investigate the affordability and efficiency of dentistry clinics in Isfahan province, Iran. The current work is a quantitative research, designed in three methodological steps, including two surveys and experimental studies, for understanding current deficiencies of Iranian dentistry clinics. First, we ran a survey. Then, we analyzed the results of the questionnaires which guided us to find a particular intervening package to improve the efficiency of the clinics. At the second step, we chose an inefficient clinic named Mohtasham (Iran, Isfahan) to evaluate our intervening package. Based on what the interviewees answered, we mention the most important issues to be considered for improving the efficiency of dental clinics in Isfahan. By considering mentioned problematic issues, an intervening package was designed. This intervening package was applied in Mohtasham clinic, since June 2010. It improved the clinic's income from 16328 US$ with 4125 clients in 2010, to 420,000 US$ with 14784 patients in 2012. The proposed intervening package changed this clinic to an efficient and economic one. Its income increased 5.08 times and its patient's numbers grew 4.01 times simultaneously. In other words, Mohtasham's experience demonstrates the reliability of the package and its potentiality to be applied in macro level to improve other dentistry clinics.

Pleurectomy versus pleural abrasion for primary spontaneous pneumothorax in children.

PubMed

Joharifard, Shahrzad; Coakley, Brian A; Butterworth, Sonia A

2017-05-01

Primary spontaneous pneumothorax (PSP) represents a common indication for urgent surgical intervention in children. First episodes are often managed with thoracostomy tube, whereas recurrent episodes typically prompt surgery involving apical bleb resection and pleurodesis, either via pleurectomy or pleural abrasion. The purpose of this study was to assess whether pleurectomy or pleural abrasion was associated with lower postoperative recurrence. The records of patients undergoing surgery for PSP between February 2005 and December 2015 were retrospectively reviewed. Recurrence was defined as an ipsilateral pneumothorax requiring surgical intervention. Bivariate logistic regressions were used to identify factors associated with recurrence. Fifty-two patients underwent 64 index operations for PSP (12 patients had surgery for contralateral pneumothorax, and each instance was analyzed separately). The mean age was 15.7±1.2years, and 79.7% (n=51) of patients were male. In addition to apical wedge resection, 53.1% (n=34) of patients underwent pleurectomy, 39.1% (n=25) underwent pleural abrasion, and 7.8% (n=5) had no pleural treatment. The overall recurrence rate was 23.4% (n=15). Recurrence was significantly lower in patients who underwent pleurectomy rather than pleural abrasion (8.8% vs. 40%, p<0.01). In patients who underwent pleural abrasion without pleurectomy, the relative risk of recurrence was 2.36 [1.41-3.92, p<0.01]. Recurrence of PSP is significantly reduced in patients undergoing pleurectomy compared to pleural abrasion. Level III, retrospective comparative therapeutic study. Copyright © 2017 Elsevier Inc. All rights reserved.

National Museum of Dentistry exhibition: the future is now! African Americans in dentistry.

PubMed

Dummett, Clifton O

2003-09-01

Inspired by recently published NDA II: The Story of America's Second National Dental Association and sponsored jointly by the National Dental Association Foundation and the Colgate-Palmolive Company, an historical exhibit on dentistry in the African-American community was one of the celebrations for the Golden Anniversary of the American Academy of the History of Dentistry. This exhibit premiered on Sept. 27, 2002 in the National Museum of Dentistry located on the medical/dental campus of the University of Maryland in Baltimore. The Museum recently became an affiliate of the Smithsonian Institution. Contents of the exhibit were photographs, charts, artifacts, memorabilia, etc. These materials presented an overview of African-American activities in dental education, research, patient care, general practice, dental specialities, military service, and public health. Also included were inter-racial relationships, socioeconomic developments, and participation in civil rights endeavors that played a major role in changing out-dated accepted customs. The exhibit's purpose was to celebrate dentistry's ministrations as a health professional among African Americans in particular and the nation at large over the past two centuries. Respect for and progress of black dentists paralleled that of black physicians who were instrumental in including dentist and pharmacists as equal members in the National Medical Association since the latter's inception in 1895.

Study of Dominant Factors Affecting Cerchar Abrasivity Index

NASA Astrophysics Data System (ADS)

Rostami, Jamal; Ghasemi, Amireza; Alavi Gharahbagh, Ehsan; Dogruoz, Cihan; Dahl, Filip

2014-09-01

The Cerchar abrasion index is commonly used to represent rock abrasion for estimation of bit life and wear in various mining and tunneling applications. Although the test is simple and fast, there are some discrepancies in the test results related to the equipment used, condition of the rock surface, operator skills, and procedures used in conducting and measuring the wear surface. This paper focuses on the background of the test and examines the influence of various parameters on Cerchar testing including pin hardness, surface condition of specimens, petrographical and geomechanical properties, test speed, applied load, and method of measuring wear surface. Results of Cerchar tests on a set of rock specimens performed at different laboratories are presented to examine repeatability of the tests. In addition, the preliminary results of testing with a new device as a potential alternative testing system for rock abrasivity measurement are discussed.

Developing patient safety in dentistry.

PubMed

Pemberton, M N

2014-10-01

Patient safety has always been important and is a source of public concern. Recent high profile scandals and subsequent reports, such as the Francis report into the failings at Mid Staffordshire, have raised those concerns even higher. Mortality and significant morbidity associated with the practice of medicine has led to many strategies to help improve patient safety, however, with its lack of associated mortality and lower associated morbidity, dentistry has been slower at systematically considering how patient safety can be improved. Recently, several organisations, researchers and clinicians have discussed the need for a patient safety culture in dentistry. Strategies are available to help improve patient safety in healthcare and deserve further consideration in dentistry.

Physical ergonomics in veterinary dentistry.

PubMed

DeForge, Donald H

2002-12-01

Ergonomics is the application of a body of knowledge addressing the interactions between man and the total working environment, such as atmosphere, heat, light and sound, as well as all tools and equipment of the workplace. Work related musculoskeletal injuries, caused by poor posture, have been discussed in human dentistry for several years. Veterinary dentistry, as a relatively new specialty within veterinary medicine, should address the ergonomics of poor posture without further delay to prevent work-related injuries. The generalist, as well as the specialist and their technicians, are subject to various neck and back disorders if proper ergonomic recommendations are not followed. This review article highlights basic ergonomic design principles for illumination and posture in veterinary dentistry.

Baking soda as an abrasive in toothpastes: Mechanism of action and safety and effectiveness considerations.

PubMed

Hara, Anderson T; Turssi, Cecilia P

2017-11-01

Toothpastes can be formulated with different abrasive systems, depending on their intended clinical application. This formulation potentially affects their effectiveness and safety and, therefore, requires proper understanding. In this article, the authors focused on abrasive aspects of toothpastes containing sodium bicarbonate (baking soda), which have gained considerable attention because of their low abrasivity and good compatibility, while providing clinical effectiveness (further detailed in the other articles of this special issue). The authors first appraised the role of toothpaste abrasivity on tooth wear, exploring some underlying processes and the existing methods to determine toothpaste abrasivity. The authors reviewed the available data on the abrasivity of toothpastes containing baking soda and reported a summary of findings highlighting the clinical implications. On the basis of the collected evidence, baking soda has an intrinsic low-abrasive nature because of its comparatively lower hardness in relation to enamel and dentin. Baking soda toothpastes also may contain other ingredients, which can increase their stain removal effectiveness and, consequently, abrasivity. Even those formulations have abrasivity well within the safety limit regulatory agencies have established and, therefore, can be considered safe. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

Three-Body Abrasion Testing Using Lunar Dust Simulants to Evaluate Surface System Materials

NASA Technical Reports Server (NTRS)

Kobrick, Ryan L.; Budinski, Kenneth G.; Street, Kenneth W., Jr.; Klaus, David M.

2010-01-01

Numerous unexpected operational issues relating to the abrasive nature of lunar dust, such as scratched visors and spacesuit pressure seal leaks, were encountered during the Apollo missions. To avoid reoccurrence of these unexpected detrimental equipment problems on future missions to the Moon, a series of two- and three-body abrasion tests were developed and conducted in order to begin rigorously characterizing the effect of lunar dust abrasiveness on candidate surface system materials. Two-body scratch tests were initially performed to examine fundamental interactions of a single particle on a flat surface. These simple and robust tests were used to establish standardized measurement techniques for quantifying controlled volumetric wear. Subsequent efforts described in the paper involved three-body abrasion testing designed to be more representative of actual lunar interactions. For these tests, a new tribotester was developed to expose samples to a variety of industrial abrasives and lunar simulants. The work discussed in this paper describes the three-body hardware setup consisting of a rotating rubber wheel that applies a load on a specimen as a loose abrasive is fed into the system. The test methodology is based on ASTM International (ASTM) B611, except it does not mix water with the abrasive. All tests were run under identical conditions. Abraded material specimens included poly(methyl methacrylate) (PMMA), hardened 1045 steel, 6061-T6 aluminum (Al) and 1018 steel. Abrasives included lunar mare simulant JSC- 1A-F (nominal size distribution), sieved JSC-1A-F (<25 m particle diameter), lunar highland simulant NU-LHT-2M, alumina (average diameter of 50 m used per ASTM G76), and silica (50/70 mesh used per ASTM G65). The measured mass loss from each specimen was converted using standard densities to determine total wear volume in cm3. Abrasion was dominated by the alumina and the simulants were only similar to the silica (i.e., sand) on the softer materials of

The effects of an airborne-particle abrasion and silica-coating on the bond strength between grooved titanium alloy temporary cylinders and provisional veneering materials.

PubMed

Wei, Ann Yu-Chieh; Sharma, Arun B; Watanabe, Larry G; Finzen, Frederick C

2011-03-01

without surface treatment. Group AbBisGMA demonstrated the lowest mean value (3.49 MPa) compared to the other groups. Airborne-particle abrasion and silica-coating treatment did not improve the bond between grooved titanium alloy temporary cylinders and provisional veneering materials. It weakened the provided mechanical retention, especially when it was used with BisGMA veneering material. Material choice, whether it was polymethyl methacrylate or BisGMA, did not make a statistically significant difference. Copyright © 2011 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Surface characterization of current composites after toothbrush abrasion.

PubMed

Takahashi, Rena; Jin, Jian; Nikaido, Toru; Tagami, Junji; Hickel, Reinhard; Kunzelmann, Karl-Heinz

2013-01-01

The present study was designed to evaluate the surface roughness and the gloss of current composites before and after toothbrush abrasion. We assessed forty dimensionally standardized composite specimens (n=8/group) from five composites: two nanohybrids (i. e., IPS Empress Direct Enamel and IPS Empress Direct Dentin), two microhybrids (i. e., Clearfil AP-X and Filtek Z250) and one organically modified ceramics (Admira). All of the specimens were polished with 4000-grid silicon carbide papers. Surface roughness was measured with a profilometer and gloss was measured with a glossmeter before and after powered toothbrush abrasion with a 1:1 slurry (dentifrice/tap water) at 12,000 strokes in a toothbrush simulator. There was a significant increase in the surface roughness and a reduction in gloss after toothbrush abrasion in all of the composites except Clearfil AP-X (p<0.05). Simple regression analysis showed that there was not an association between the surface roughness and the gloss (R(2)=0.191, p<0.001).

Microhardness evaluation of silorane and methacrylate composites submitted to erosion and abrasion processes

PubMed Central

Gazola, Eloá Aguiar; Rego, Marcos Augusto; Brandt, William Cunha; D’Arce, Maria Beatriz Freitas; Liporoni, Priscila Christiane Suzy

2015-01-01

Abstract Objective: The aim of this study was to evaluate the Knoop hardness number (KHN) of methacrylate (MC) and silorane (SC) composites after being submitted to erosion and abrasion processes. Material and methods: Forty samples were made with each composite: MC and SC. The samples were divided into eight groups (n = 10) according to the type of composite (G1–G4, MC; G5–G8, SC) and the beverages involved in the erosion process (G1 and G5 – Control (C), without erosion, with abrasion; G2 and G6 – Orange Juice (OJ), abrasion; G3 and G7 – Smirnoff Ice® (SI), abrasion; G4 and G8 – Gatorade® (GA), abrasion). The KHN test was performed 24 h after the last cycle of erosion/abrasion. Results: The MC groups showed smaller KHN values for the SI group (p < 0.05) when compared to the Control and OJ groups; however, for the SC groups, no differences were found (p > 0.05). Conclusion: Methacrylate composite when submitted to acidic beverages erosive challenge combined with abrasive process might alter its surface microhardness. However, the beverages used in the present study were not able to interfere in silorane composite surface microhardness. PMID:28642903

Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics

NASA Astrophysics Data System (ADS)

Li, Junye; Meng, Wenqing; Dong, Kun; Zhang, Xinming; Zhao, Weihong

2018-01-01

Abrasive flow polishing plays an important part in modern ultra-precision machining. Ultrafine particles suspended in the medium of abrasive flow removes the material in nanoscale. In this paper, three-dimensional molecular dynamics (MD) simulations are performed to investigate the effect of impacting direction on abrasive cutting process during abrasive flow polishing. The molecular dynamics simulation software Lammps was used to simulate the cutting of single crystal copper with SiC abrasive grains at different cutting angles (0o-45o). At a constant friction coefficient, we found a direct relation between cutting angle and cutting force, which ultimately increases the number of dislocation during abrasive flow machining. Our theoretical study reveal that a small cutting angle is beneficial for improving surface quality and reducing internal defects in the workpiece. However, there is no obvious relationship between cutting angle and friction coefficient.

Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics.

PubMed

Li, Junye; Meng, Wenqing; Dong, Kun; Zhang, Xinming; Zhao, Weihong

2018-01-11

Abrasive flow polishing plays an important part in modern ultra-precision machining. Ultrafine particles suspended in the medium of abrasive flow removes the material in nanoscale. In this paper, three-dimensional molecular dynamics (MD) simulations are performed to investigate the effect of impacting direction on abrasive cutting process during abrasive flow polishing. The molecular dynamics simulation software Lammps was used to simulate the cutting of single crystal copper with SiC abrasive grains at different cutting angles (0 o -45 o ). At a constant friction coefficient, we found a direct relation between cutting angle and cutting force, which ultimately increases the number of dislocation during abrasive flow machining. Our theoretical study reveal that a small cutting angle is beneficial for improving surface quality and reducing internal defects in the workpiece. However, there is no obvious relationship between cutting angle and friction coefficient.

Dental traumatology: an orphan in pediatric dentistry?

PubMed

Andreasen, Jens Ove; Lauridsen, Eva; Daugaard-Jensen, Jette

2009-01-01

Traumatic dental injuries are very frequent during childhood and adolescence. In fact, 2 out of 3 children have suffered a traumatic dental injury before adulthood. This fact links dental traumatology to pediatric dentistry. Unfortunately, this is not reflected by active participation by pediatric dentists in acute treatment, follow-up, and research. To examine the status of pediatric dentistry in relation to dental trauma, a publication analysis was undertaken in 1980, 1990, 2000, and 2007 about trauma articles published in 4 pediatric journals: journal of Dentistry for Children, Pediatric Dentistry, The journal of Pedodontics, and the International journal of Pediatric Dentistry. This study shows an average publication rate of trauma articles of approximately 3 percent of all articles published and with no improvement in later decennia. If only clinical studies are considered (leaving out case reports), the publication rate is less than 1 percent--completely out of proportion to the size of the problem dental trauma impose in children.

Dentin abrasivity of various desensitizing toothpastes.

PubMed

Arnold, W H; Gröger, Ch; Bizhang, M; Naumova, E A

2016-04-02

The aim of this study was to compare the abrasivity of various commercially available toothpastes that claim to reduce dentin hypersensitivity. Dentin discs were prepared from 70 human extracted molars. The discs were etched with lemon juice for 5 min, and one half of the discs were covered with aluminum tape. Following this, they were brushed with 6 different toothpastes, simulating a total brushing time of 6 months. As a negative control, discs were brushed with tap water only. The toothpastes contained pro-arginine and calcium carbonate, strontium acetate, stannous fluoride, zinc carbonate and hydroxyapatite, new silica, or tetrapotassium pyrophosphate and hydroxyapatite. After brushing, the height differences between the control halves and the brushed halves were determined with a profilometer and statistically compared using a Mann-Whitney U test for independent variables. A significant difference (p < 0.001) in height difference between the controls and the toothpaste-treated samples was found in all cases, except for the stannous fluoride-containing toothpaste (p = 0.583). The highest abrasion was found in the toothpaste containing zinc carbonate and hydroxyapatite, and the lowest was found in the toothpaste containing pro-arginine and calcium carbonate. Desensitizing toothpastes with different desensitizing ingredients have different levels of abrasivity, which may have a negative effect on their desensitizing abilities over a long period of time.

Computational Fluid Dynamic Simulation of Flow in Abrasive Water Jet Machining

NASA Astrophysics Data System (ADS)

Venugopal, S.; Sathish, S.; Jothi Prakash, V. M.; Gopalakrishnan, T.

2017-03-01

Abrasive water jet cutting is one of the most recently developed non-traditional manufacturing technologies. In this machining, the abrasives are mixed with suspended liquid to form semi liquid mixture. The general nature of flow through the machining, results in fleeting wear of the nozzle which decrease the cutting performance. The inlet pressure of the abrasive water suspension has main effect on the major destruction characteristics of the inner surface of the nozzle. The aim of the project is to analyze the effect of inlet pressure on wall shear and exit kinetic energy. The analysis could be carried out by changing the taper angle of the nozzle, so as to obtain optimized process parameters for minimum nozzle wear. The two phase flow analysis would be carried by using computational fluid dynamics tool CFX. It is also used to analyze the flow characteristics of abrasive water jet machining on the inner surface of the nozzle. The availability of optimized process parameters of abrasive water jet machining (AWJM) is limited to water and experimental test can be cost prohibitive. In this case, Computational fluid dynamics analysis would provide better results.

Informed Consent in Dentistry.

PubMed

Reid, Kevin I

2017-03-01

A review of literature regarding informed consent in dentistry reveals a paucity of information and minimal scholarship devoted to this subject. But this begs the question about informed consent somehow being different for dentistry than for medicine or other healthcare delivery. My account draws distinctions where appropriate but is rooted in the premise that informed consent is an ethical construct applicable to vulnerable people as patients independent of what type of treatment or body part being considered. This paper highlights the crucial importance of the process of informed consent and refusal in dentistry, underscoring its important place in oral healthcare. This paper will not address the unique circumstances involving consent in those without capacity or focus on informed consent in the research setting; our focus will be on those patients with full decisionmaking capacity in the clinical setting. I will emphasize the importance of disclosure of treatment options and highlight the benefits of shared-decision-making in the informed consent process.

Natural medicaments in dentistry

PubMed Central

Sinha, Dakshita J.; Sinha, Ashish A.

2014-01-01

The major objective in root canal treatment is to disinfect the entire root canal system. Cleaning, shaping, and use of antimicrobial medicaments are effective in reducing the bacterial load to some extent, but some bacteria do remain behind and multiply, causing reinfection. Taking into consideration the ineffectiveness, potential side-effects and safety concerns of synthetic drugs, the herbal alternatives for endodontic usage might prove to be advantageous. Over the past decade, interest in drugs derived from medicinal plants has markedly increased. Phytomedicine has been used in dentistry as anti-inflammatory, antibiotic, analgesic, sedative and also as endodontic irrigant. Herbal preparations can be derived from the root, leaves, seeds, stem, and flowers. The PubMed database search revealed that the reference list for natural medicaments featured 1480 articles and in dentistry 173 articles. A forward search was undertaken on the selected articles and author names. This review focuses on various natural drugs and products as well as their therapeutic applications when used as phytomedicine in dentistry. PMID:25558153

Abrasion-ablation model for neutron production in heavy ion reactions

NASA Technical Reports Server (NTRS)

Cucinotta, Francis A.; Wilson, John W.; Townsend, Lawrence W.

1995-01-01

In heavy ion reactions, neutron production at forward angles is observed to occur with a Gaussian shape that is centered near the beam energy and extends to energies well above that of the beam. This paper presents an abrasion-ablation model for making quantitative predictions of the neutron spectrum. To describe neutrons produced from the abrasion step of the reaction where the projectile and target overlap, the authors use the Glauber model and include effects of final-state interactions. They then use the prefragment mass distribution from abrasion with a statistical evaporation model to estimate the neutron spectrum resulting from ablation. Measurements of neutron production from Ne and Nb beams are compared with calculations, and good agreement is found.

What's new in paediatric dentistry?

NASA Astrophysics Data System (ADS)

Vitale, M. C.

2016-03-01

Since the early 80's, the use of laser has been introduced in the daily dental practice and the technological development has also provided over time to optimize its use. Various types of lasers with different wavelengths have been developed for use in a handy, easy and ergonomic manner. In daily paediatric dentistry, laser could be a very useful medical device which can completely replace the traditional high hand-piece and bur to realize a "micro-invasive" dentistry and a "clean" surgery, without bleeding and sutures. According to the international literature and in the light of recent researches, this work could give an overview on assisted laser therapy in paediatric dentistry, highlighting advantages and disadvantages of this new technology and pointing out the high compliance of the young patient.

Surface Abrasive Torsion for Improved Mechanical Properties and Microstructure

NASA Astrophysics Data System (ADS)

Moon, Ji Hyun; Baek, Seung Mi; Lee, Seok Gyu; Yoon, Jae Ik; Lee, Sunghak; Kim, Hyoung Seop

2018-05-01

A novel process of discrete surface abrasion during simple torsion (ST), named "surface abrasive torsion (SAT)," is proposed to overcome the limitation of ST, i.e., insufficient strain for severe plastic deformation (SPD) due to cracks initiated on the surface, by removing the roughened surface region. The effect of SAT on delayed crack initiation was explained using finite element simulations. Larger shear deformation applicable to the specimen in SAT than ST was demonstrated experimentally.

[Collective oral health: ways from sanitary dentistry to buccality].

PubMed

Narvai, Paulo Capel

2006-08-01

This essay focuses on the pioneer activities of public health dentistry in Brazil and its evolution in the 20th century with emphasis on the emergency of a landmark, the sanitary dentistry. Social and preventive dentistry and market dentistry, with reference to the main theoretical works representative of these trends, are presented. The essential characteristics of collective oral health (Brazilian variant of public health dentistry) and buccality are presented. The relationship between collective oral health and collective health as well as the implications of the buccality concept for the development of public health dentistry actions and new guidance of clinical practice in public services of the Brazilian Health System (SUS) are discussed. The key elements of an agenda for collective oral health based on proposals presented at the 3rd National Conference on Oral Health are addressed.

Behaviors of 40Cr steel treated by laser quenching on impact abrasive wear

NASA Astrophysics Data System (ADS)

Chen, Zhikai; Zhu, Qinghai; Wang, Jing; Yun, Xiao; He, Bing; Luo, Jingshuai

2018-07-01

In present work, laser quenching had been carried out to improve the impact abrasive wear resistance of 40Cr steel. The distinct microstructure between original and quenched region was demonstrated after laser quenching. Since the effect of temperature and cooling rate, the phase combinations were apparently different for quenched layer in depth. The impact abrasive wear resistance of sample was experimentally investigated and the improved level was assessed in light of the average mass loss of three repetitive tests. Worn surface was detected by means of SEM, OM and EDS, and results showed that three typical failure modes were performed during the processing of impact abrasive wear, including abrasive wear, impact effect and rolling contact fatigue. Basing on the different worn surface profile, the mainly failure mode was respectively pointed out for matrix and quenched sample, which was significantly in accordance with the result of impact abrasive wear.

The legal business of dentistry.

PubMed

Barrabee, Steve; Kowalski, Michael

2009-09-01

Upon graduation and licensure, most dentists anticipate going into the profession of providing dental heath care to patients in an office or clinic setting. The profession is also the business of dentistry. Failure to appreciate documentation requirements for the business of dentistry can result in legal battles that are time-consuming and emotionally draining. This article provides an introduction, issue spotting, and tips to avoid those legal battles.

Advances of Proteomic Sciences in Dentistry

PubMed Central

Khurshid, Zohaib; Zohaib, Sana; Najeeb, Shariq; Zafar, Muhammad Sohail; Rehman, Rabia; Rehman, Ihtesham Ur

2016-01-01

Applications of proteomics tools revolutionized various biomedical disciplines such as genetics, molecular biology, medicine, and dentistry. The aim of this review is to highlight the major milestones in proteomics in dentistry during the last fifteen years. Human oral cavity contains hard and soft tissues and various biofluids including saliva and crevicular fluid. Proteomics has brought revolution in dentistry by helping in the early diagnosis of various diseases identified by the detection of numerous biomarkers present in the oral fluids. This paper covers the role of proteomics tools for the analysis of oral tissues. In addition, dental materials proteomics and their future directions are discussed. PMID:27187379

Advances of Proteomic Sciences in Dentistry.

PubMed

Khurshid, Zohaib; Zohaib, Sana; Najeeb, Shariq; Zafar, Muhammad Sohail; Rehman, Rabia; Rehman, Ihtesham Ur

2016-05-13

Applications of proteomics tools revolutionized various biomedical disciplines such as genetics, molecular biology, medicine, and dentistry. The aim of this review is to highlight the major milestones in proteomics in dentistry during the last fifteen years. Human oral cavity contains hard and soft tissues and various biofluids including saliva and crevicular fluid. Proteomics has brought revolution in dentistry by helping in the early diagnosis of various diseases identified by the detection of numerous biomarkers present in the oral fluids. This paper covers the role of proteomics tools for the analysis of oral tissues. In addition, dental materials proteomics and their future directions are discussed.

Lasers and radiofrequency devices in dentistry.

PubMed

Green, James; Weiss, Adam; Stern, Avichai

2011-07-01

Advances in technology are changing the ways that patients experience dental treatment. Technology helps to decrease treatment time and makes the treatment more comfortable for the patient. One technological advance is the use of lasers in dentistry. Lasers are providing more efficient, more comfortable, and more predictable outcomes for patients. Lasers are used in all aspects of dentistry, including operative, periodontal, endodontic, orthodontic, and oral and maxillofacial surgery. Lasers are used for soft and hard tissue procedures in the treatment of pathologic conditions and for esthetic procedures. This article discusses how lasers work and their application in the various specialties within dentistry. Copyright © 2011 Elsevier Inc. All rights reserved.

Evaluation of Needle Gun and Abrasive Blasting Technologies in Bridge Paint Removal Practices.

PubMed

Randall, Paul M; Kranz, Paul B; Sonntag, Mary L; Stadelmaier, James E

1998-03-01

This paper reviews the results of a U.S. Environmental Protection Agency (EPA) study that assessed needle gun technology as an alternative to conventional abrasive blasting technology to remove lead-based paint from steel bridges in western New York State. The study analyzed the operational and logistical aspects as they relate to worker health and safety, environmental protection, hazardous waste generation, and costs as compared to those arising from conventional abrasive blasting. In this 1992 EPA study, the costs and the product quality aspects favored conventional abrasive blasting over the needle gun technology for removing lead paint. However, abrasive blasting exposed workers to airborne lead levels that exceeded Permissible Exposure Limits (PELs) as established by the Occupational Safety and Health Administration (OSHA), as well as emitting high levels of lead-contaminated dusts and debris into the environment. It was estimated that more than 500 lbs of lead-contaminated spent abrasives and paint waste were released into the environment during paint removal operations. The needle gun system reduced (up to 97.5%) the generation of hazardous waste and the airborne concentrations (up to 99%) of respirable dusts and lead-containing particulates generated during paint removal operations. However, labor costs for the needle gun were three times higher than those for abrasive blasting primarily because of slower production rates that necessitated more operating personnel. The higher labor costs of the needle gun are partially offset by the increased costs associated with the expendable abrasive blast media and hazardous waste disposal. In the EPA study, the productivity of the needle gun system was 12.2 ft 2 /hr vs. 147.5 ft 2 /hr for abrasive blasting. A post blast was needed for the needle gun system to meet surface preparation specifications. When factoring in the costs of full containment structures to meet OSHA's 1993 Lead Exposure in Construction regulation

Comparative study of talc poudrage versus pleural abrasion for the treatment of primary spontaneous pneumothorax†

PubMed Central

Moreno-Merino, Sergio; Congregado, Miguel; Gallardo, Gregorio; Jimenez-Merchan, Rafael; Trivino, Ana; Cozar, Fernando; Lopez-Porras, Marta; Loscertales, Jesus

2012-01-01

Primary spontaneous pneumothorax is a pathology mainly affecting healthy young patients. Clinical guidelines do not specify the type of pleurodesis that should be conducted, due to the lack of comparative studies on the different techniques. The aim of this study was to compare talc poudrage and pleural abrasion in the treatment of spontaneous pneumothorax. A retrospective comparative study was performed, including 787 patients with primary spontaneous pneumothorax. The 787 patients were classified into two groups: Group A (pleural abrasion) n = 399 and Group B (talc pleurodesis) n = 388. The variables studied were recurrence, surgical time, morbidity and in-hospital length of stay. Statistical analysis was done by an unpaired t-test and Fisher's exact test (SSPS 18.0). Statistically significant differences were observed in the variables: surgical time (A: 46 ± 12.3; B: 37 ± 11.8 min; P < 0.001); length of stay (A: 4.7 ± 2.5; B: 4.3 ± 1.8 days; P = 0.01); apical air camera (A: 25; B: 4; P < 0.001); pleural effusion (A: 6; B: 0; P = 0.05). Talc poudrage shows shorter surgical times and length of stay, and lower re-intervention rates. Morbidity is lower in patients with talc poudrage. Statistically significant differences were not observed in recurrence, persistent air leaks, atelectasis and haemothorax. PMID:22514256

Development of feedback-speed-control system of fixed-abrasive tool for mat-surface fabrication

NASA Astrophysics Data System (ADS)

Yanagihara, K.; Kita, R.

2018-01-01

This study deals with the new method to fabricate a mat-surface by using fixed-abrasive tool. Mat-surface is a surface with microscopic irregularities whose dimensions are close to the wavelengths of visible light (400-700 nanometers). In order to develop the new method to fabricate mat-surface without pre-masking and large scale back up facility, utilization of fixed-abrasive tool is discussed. The discussion clarifies that abrasives in shot blasting are given kinetic energy along to only plunge-direction while excluding traverse-direction. If the relative motion between tool and work in fixed-abrasive process can be realized as that in blasting, mat-surface will be accomplished with fixed-abrasive process. To realize the proposed idea, new surface-fabrication system to which is adopted feedback-speed-control of abrasive wheel has been designed. The system consists of micro-computer unit (MPU), work-speed sensor, fixed-abrasive wheel, and wheel driving unit. The system can control relative speed between work and wheel in optimum range to produce mat-surface. Finally experiment to verify the developed system is carried out. The results of experiments show that the developed system is effective and it can produce the surface from grinding to mat-surface seamlessly.

Toothbrushing abrasion susceptibility of enamel and dentin bleached with calcium-supplemented hydrogen peroxide gel.

PubMed

Borges, A B; Santos, L F T F; Augusto, M G; Bonfiette, D; Hara, A T; Torres, C R G

2016-06-01

The objective of this study was to evaluate enamel and dentin susceptibility to toothbrushing abrasion, after bleaching with 7.5% hydrogen peroxide (HP) gel supplemented or not with 0.5% calcium gluconate (Ca). Toothbrushing was performed immediately and 1h after bleaching, with two suspensions (high and low abrasivity). Bovine enamel and dentin specimens were divided into 12 groups (n=10) according to the bleaching gel (with and without Ca), slurry abrasivity (high or low) and elapsed time after bleaching (immediately and after 1h). As control, a group was not bleached, but abraded. The treatment cycle (7 d) consisted of bleaching (1h) and toothbrushing (135 strokes/day) immediatelly or after 1h of artificial saliva exposure. Surface roughness and surface loss (μm) were measured by profilometry and analysed by three-way ANOVA (5%). Surface roughness means were significantly influenced by slurry abrasivity (p<0.0001). For enamel loss, significant triple interaction was observed (p<0.0001). HP-bleached groups and immediately brushed with high-abrasive slurry exhibited increased loss (1.41±0.14) compared to other groups (μm). Control and HP+Ca-bleached groups brushed after 1h with low abrasive slurry presented the lowest loss (0.21±0.03/0.27±0.02). For dentin loss, significant interaction was observed for bleaching and interval factors (p<0.001). 7.5%HP-bleached groups and immediately brushed showed significantly higher loss (8.71±2.45) than the other groups. It was concluded that surface roughness increased when high abrasive was used, independently of bleaching. 7.5%HP increased enamel and dentin loss, mainly with high abrasive slurries. Calcium supplementation of bleaching gel reduced surface loss. Additionally, in order to minimize tooth wear susceptibility, it is recommended to delay brushing after bleaching. After bleaching gel application, postponing toothbrushing is recommended, as well as brushing with low abrasive dentifrices. Additionally

Abrasive rolling effects on material removal and surface finish in chemical mechanical polishing analyzed by molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Si, Lina; Guo, Dan; Luo, Jianbin; Lu, Xinchun; Xie, Guoxin

2011-04-01

In an abrasive chemical mechanical polishing (CMP) process, materials were considered to be removed by abrasive sliding and rolling. Abrasive sliding has been investigated by many molecular dynamics (MD) studies; while abrasive rolling was usually considered to be negligible and therefore was rarely investigated. In this paper, an MD simulation was used to study the effects of abrasive rolling on material removal and surface finish in the CMP process. As the silica particle rolled across the silicon substrate, some atoms of the substrate were dragged out from their original positions and adhered to the silica particle, leaving some atomic vacancies on the substrate surface. Meanwhile, a high quality surface could be obtained. During the abrasive rolling process, the influencing factors of material removal, e.g., external down force and driving force, were also discussed. Finally, MD simulations were carried out to examine the effects of abrasive sliding on material removal under the same external down force as abrasive rolling. The results showed that the ability of abrasive rolling to remove material on the atomic scale was not notably inferior to that of abrasive sliding. Therefore, it can be proposed that both abrasive sliding and rolling play important roles in material removal in the abrasive CMP of the silicon substrate.

Target correlation effects on neutron-nucleus total, absorption, and abrasion cross sections

NASA Technical Reports Server (NTRS)

Cucinotta, Francis A.; Townsend, Lawrence W.; Wilson, John W.

1991-01-01

Second order optical model solutions to the elastic scattering amplitude were used to evaluate total, absorption, and abrasion cross sections for neutron nucleus scattering. Improved agreement with experimental data for total and absorption cross sections is found when compared with first order (coherent approximation) solutions, especially below several hundred MeV. At higher energies, the first and second order solutions are similar. There are also large differences in abrasion cross section calculations; these differences indicate a crucial role for cluster knockout in the abrasion step.

Impact Capacity Reduction in Railway Prestressed Concrete Sleepers with Surface Abrasions

NASA Astrophysics Data System (ADS)

Ngamkhanong, Chayut; Li, Dan; Kaewunruen, Sakdirat

2017-10-01

Railway sleepers (also called ‘railroad tie’ in North America) embedded in ballasted railway tracks are a main part of railway track structures. Its important role is to transfer the loads evenly from the rails to a wider area of ballast bed and to secure rail gauge and enable safe passages of rolling stocks. By nature, railway infrastructure is nonlinear, evidenced by its behaviours, geometry and alignment, wheel-rail contact and operational parameters such as tractive efforts. Based on our critical review, the dynamic behaviour of railway sleepers has not been fully investigated, especially when the sleepers are deteriorated by excessive wears. In fact, the ballast angularity causes differential abrasions on the soffit or bottom surface of sleepers (especially at railseat zone). Furthermore, in sharp curves and rapid gradient change, longitudinal and lateral dynamics of rails increase the likelihood of railseat abrasions in concrete sleepers due to the unbalanced loading conditions. This paper presents a structural capacity of concrete sleepers under dynamic transient loading. The modified compression field theory for ultimate strength design of concrete sleepers under impact loading will be highlighted in this study. The influences of surface abrasions, including surface abrasion and soffit abrasion, on the dynamic behaviour of prestressed concrete sleepers, are firstly highlighted. The outcome of this study will improve the rail maintenance and inspection criteria in order to establish appropriate and sensible remote track condition monitoring network in practice. Moreover, this study will also improve the understanding of the fundamental dynamic behaviour of prestressed concrete sleepers with surface abrasions. The insight into these behaviours will not only improve safety and reliability of railway infrastructure but will enhance the structural safety of other concrete structures.

Neural network approximation of tip-abrasion effects in AFM imaging

NASA Astrophysics Data System (ADS)

Bakucz, Peter; Yacoot, Andrew; Dziomba, Thorsten; Koenders, Ludger; Krüger-Sehm, Rolf

2008-06-01

The abrasion (wear) of tips used in scanning force microscopy (SFM) directly influences SFM image quality and is therefore of great relevance to quantitative SFM measurements. The increasing implementation of automated SFM measurement schemes has become a strong driving force for increasing efforts towards the prediction of tip wear, as it needs to be ensured that the probe is exchanged before a level of tip wear is reached that adversely affects the measurement quality. In this paper, we describe the identification of tip abrasion in a system of SFM measurements. We attempt to model the tip-abrasion process as a concatenation of a mapping from the measured AFM data to a regression vector and a nonlinear mapping from the regressor space to the output space. The mapping is formed as a basis function expansion. Feedforward neural networks are used to approximate this mapping. The one-hidden layer network gave a good quality of fit for the training and test sets for the tip-abrasion system. We illustrate our method with AFM measurements of both fine periodic structures and randomly oriented sharp features and compare our neural network results with those obtained using other methods.

Electron Microscopy Abrasion Analysis of Candidate Fabrics for Planetary Space Suit Protective Overgarment Application

NASA Technical Reports Server (NTRS)

Hennessy, Mary J.

1992-01-01

The Electron Microscopy Abrasion Analysis of Candidate Fabrics for Planetary Space Suit Protective Overgarment Application is in support of the Abrasion Resistance Materials Screening Test. The fundamental assumption made for the SEM abrasion analysis was that woven fabrics to be used as the outermost layer of the protective overgarment in the design of the future, planetary space suits perform best when new. It is the goal of this study to determine which of the candidate fabrics was abraded the least in the tumble test. The sample that was abraded the least will be identified at the end of the report as the primary candidate fabric for further investigation. In addition, this analysis will determine if the abrasion seen by the laboratory tumbled samples is representative of actual EVA Apollo abrasion.

Minimum intervention dentistry: periodontics and implant dentistry.

PubMed

Darby, I B; Ngo, L

2013-06-01

This article will look at the role of minimum intervention dentistry in the management of periodontal disease. It will discuss the role of appropriate assessment, treatment and risk factors/indicators. In addition, the role of the patient and early intervention in the continuing care of dental implants will be discussed as well as the management of peri-implant disease. © 2013 Australian Dental Association.

A profilometry-based dentifrice abrasion Method for V8 brushing machines. Part I: Introduction to RDA-PE.

PubMed

White, Donald J; Schneiderman, Eva; Colón, Ellen; St John, Samuel

2015-01-01

This paper describes the development and standardization of a profilometry-based method for assessment of dentifrice abrasivity called Radioactive Dentin Abrasivity - Profilometry Equivalent (RDA-PE). Human dentine substrates are mounted in acrylic blocks of precise standardized dimensions, permitting mounting and brushing in V8 brushing machines. Dentin blocks are masked to create an area of "contact brushing." Brushing is carried out in V8 brushing machines and dentifrices are tested as slurries. An abrasive standard is prepared by diluting the ISO 11609 abrasivity reference calcium pyrophosphate abrasive into carboxymethyl cellulose/glycerin, just as in the RDA method. Following brushing, masked areas are removed and profilometric analysis is carried out on treated specimens. Assessments of average abrasion depth (contact or optical profilometry) are made. Inclusion of standard calcium pyrophosphate abrasive permits a direct RDA equivalent assessment of abrasion, which is characterized with profilometry as Depth test/Depth control x 100. Within the test, the maximum abrasivity standard of 250 can be created in situ simply by including a treatment group of standard abrasive with 2.5x number of brushing strokes. RDA-PE is enabled in large part by the availability of easy-to-use and well-standardized modern profilometers, but its use in V8 brushing machines is enabled by the unique specific conditions described herein. RDA-PE permits the evaluation of dentifrice abrasivity to dentin without the requirement of irradiated teeth and infrastructure for handling them. In direct comparisons, the RDA-PE method provides dentifrice abrasivity assessments comparable to the gold industry standard RDA technique.

Nanomaterials in preventive dentistry

NASA Astrophysics Data System (ADS)

Hannig, Matthias; Hannig, Christian

2010-08-01

The prevention of tooth decay and the treatment of lesions and cavities are ongoing challenges in dentistry. In recent years, biomimetic approaches have been used to develop nanomaterials for inclusion in a variety of oral health-care products. Examples include liquids and pastes that contain nano-apatites for biofilm management at the tooth surface, and products that contain nanomaterials for the remineralization of early submicrometre-sized enamel lesions. However, the treatment of larger visible cavities with nanomaterials is still at the research stage. Here, we review progress in the development of nanomaterials for different applications in preventive dentistry and research, including clinical trials.

Abrasion resistant heat pipe

DOEpatents

Ernst, D.M.

1984-10-23

A specially constructed heat pipe is described for use in fluidized bed combustors. Two distinct coatings are spray coated onto a heat pipe casing constructed of low thermal expansion metal, each coating serving a different purpose. The first coating forms aluminum oxide to prevent hydrogen permeation into the heat pipe casing, and the second coating contains stabilized zirconium oxide to provide abrasion resistance while not substantially affecting the heat transfer characteristics of the system.

Feasibility Study on Cutting HTPB Propellants with Abrasive Water Jet

NASA Astrophysics Data System (ADS)

Jiang, Dayong; Bai, Yun

2018-01-01

Abrasive water jet is used to carry out the experiment research on cutting HTPB propellants with three components, which will provide technical support for the engineering treatment of waste rocket motor. Based on the reliability theory and related scientific research results, the safety and efficiency of cutting sensitive HTPB propellants by abrasive water jet were experimentally studied. The results show that the safety reliability is not less than 99.52% at 90% confidence level, so the safety is adequately ensured. The cooling and anti-friction effect of high-speed water jet is the decisive factor to suppress the detonation of HTPB propellant. Compared with pure water jet, cutting efficiency was increased by 5% - 87%. The study shows that abrasive water jets meet the practical use for cutting HTPB propellants.

Abrasion of Candidate Spacesuit Fabrics by Simulated Lunar Dust

NASA Technical Reports Server (NTRS)

Gaier, James R.; Meador, Mary Ann; Rogers, Kerry J.; Sheehy, Brennan H.

2009-01-01

A protocol has been developed that produced the type of lunar soil abrasion damage observed on Apollo spacesuits. This protocol was then applied to four materials (Kevlar (DuPont), Vectran (Kuraray Co., Ltd.), Orthofabric, and Tyvek (DuPont)) that are candidates for advanced spacesuits. Three of the four new candidate fabrics (all but Vectran) were effective at keeping the dust from penetrating to layers beneath. In the cases of Kevlar and Orthofabric this was accomplished by the addition of a silicone layer. In the case of Tyvek, the paper structure was dense enough to block dust transport. The least abrasive damage was suffered by the Tyvek. This was thought to be due in large part to its non-woven paper structure. The woven structures were all abraded where the top of the weave was struck by the abrasive. Of these, the Orthofabric suffered the least wear, with both Vectran and Kevlar suffering considerably more extensive filament breakage.

3D printing in dentistry.

PubMed

Dawood, A; Marti Marti, B; Sauret-Jackson, V; Darwood, A

2015-12-01

3D printing has been hailed as a disruptive technology which will change manufacturing. Used in aerospace, defence, art and design, 3D printing is becoming a subject of great interest in surgery. The technology has a particular resonance with dentistry, and with advances in 3D imaging and modelling technologies such as cone beam computed tomography and intraoral scanning, and with the relatively long history of the use of CAD CAM technologies in dentistry, it will become of increasing importance. Uses of 3D printing include the production of drill guides for dental implants, the production of physical models for prosthodontics, orthodontics and surgery, the manufacture of dental, craniomaxillofacial and orthopaedic implants, and the fabrication of copings and frameworks for implant and dental restorations. This paper reviews the types of 3D printing technologies available and their various applications in dentistry and in maxillofacial surgery.

Quantitative image analysis for evaluating the abrasion resistance of nanoporous silica films on glass

PubMed Central

Nielsen, Karsten H.; Karlsson, Stefan; Limbach, Rene; Wondraczek, Lothar

2015-01-01

The abrasion resistance of coated glass surfaces is an important parameter for judging lifetime performance, but practical testing procedures remain overly simplistic and do often not allow for direct conclusions on real-world degradation. Here, we combine quantitative two-dimensional image analysis and mechanical abrasion into a facile tool for probing the abrasion resistance of anti-reflective (AR) coatings. We determine variations in the average coated area, during and after controlled abrasion. Through comparison with other experimental techniques, we show that this method provides a practical, rapid and versatile tool for the evaluation of the abrasion resistance of sol-gel-derived thin films on glass. The method yields informative data, which correlates with measurements of diffuse reflectance and is further supported by qualitative investigations through scanning electron microscopy. In particular, the method directly addresses degradation of coating performance, i.e., the gradual areal loss of antireflective functionality. As an exemplary subject, we studied the abrasion resistance of state-of-the-art nanoporous SiO2 thin films which were derived from 5–6 wt% aqueous solutions of potassium silicates, or from colloidal suspensions of SiO2 nanoparticles. It is shown how abrasion resistance is governed by coating density and film adhesion, defining the trade-off between optimal AR performance and acceptable mechanical performance. PMID:26656260

Is dentistry a profession? Part 3. Future challenges.

PubMed

Welie, Jos V M

2004-11-01

In 2 earlier articles a definition of professionalism was developed, and several specific professional responsibilities were deduced. This third and final article in the series examines whether dentistry qualifies as a profession. On various levels, the professionalism of dentistry is found wanting. However, attaining the status of a profession is a work in progress, which means that each profession will always have some deficiencies. The author concludes that dentistry qualifies as a profession but that it is also exhibiting a trend toward once again becoming a business (as it was before the 19th century). For the sake of honesty with the public, dentistry must make a choice between these 2 models.

Cold Atmospheric Plasma: methods of production and application in dentistry and oncology

PubMed Central

2013-01-01

Cold Atmospheric Plasma is an ionized gas that has recently been extensively studied by researchers as a possible therapy in dentistry and oncology. Several different gases can be used to produce Cold Atmospheric Plasma such as Helium, Argon, Nitrogen, Heliox, and air. There are many methods of production by which cold atmospheric plasma is created. Each unique method can be used in different biomedical areas. In dentistry, researchers have mostly investigated the antimicrobial effects produced by plasma as a means to remove dental biofilms and eradicate oral pathogens. It has been shown that reactive oxidative species, charged particles, and UV photons play the main role. Cold Atmospheric Plasma has also found a minor, but important role in tooth whitening and composite restoration. Furthermore, it has been demonstrated that Cold Atmospheric Plasma induces apoptosis, necrosis, cell detachment, and senescence by disrupting the S phase of cell replication in tumor cells. This unique finding opens up its potential therapy in oncology. PMID:24083477

Minimally Invasive Dentistry

MedlinePlus

... geta poker friv Home InfoBites Find an AGD Dentist Your Family's Oral Health About the AGD Dental ... structure. It focuses on prevention, remineralization, and minimal dentist intervention. Using scientific advances, minimally invasive dentistry allows ...

Minimally legally invasive dentistry.

PubMed

Lam, R

2014-12-01

One disadvantage of the rapid advances in modern dentistry is that treatment options have never been more varied or confusing. Compounded by a more educated population greatly assisted by online information in an increasingly litigious society, a major concern in recent times is increased litigation against health practitioners. The manner in which courts handle disputes is ambiguous and what is considered fair or just may not be reflected in the judicial process. Although legal decisions in Australia follow a doctrine of precedent, the law is not static and is often reflected by community sentiment. In medical litigation, this has seen the rejection of the Bolam principle with a preference towards greater patient rights. Recent court decisions may change the practice of dentistry and it is important that the clinician is not caught unaware. The aim of this article is to discuss legal issues that are pertinent to the practice of modern dentistry through an analysis of legal cases that have shaped health law. Through these discussions, the importance of continuing professional development, professional association and informed consent will be realized as a means to limit the legal complications of dental practice. © 2014 Australian Dental Association.

Brushing force of manual and sonic toothbrushes affects dental hard tissue abrasion.

PubMed

Wiegand, Annette; Burkhard, John Patrik Matthias; Eggmann, Florin; Attin, Thomas

2013-04-01

This study aimed to determine the brushing forces applied during in vivo toothbrushing with manual and sonic toothbrushes and to analyse the effect of these brushing forces on abrasion of sound and eroded enamel and dentin in vitro. Brushing forces of a manual and two sonic toothbrushes (low and high frequency mode) were measured in 27 adults before and after instruction of the respective brushing technique and statistically analysed by repeated measures analysis of variance (ANOVA). In the in vitro experiment, sound and eroded enamel and dentin specimens (each subgroup n = 12) were brushed in an automatic brushing machine with the respective brushing forces using a fluoridated toothpaste slurry. Abrasion was determined by profilometry and statistically analysed by one-way ANOVA. Average brushing force of the manual toothbrush (1.6 ± 0.3 N) was significantly higher than for the sonic toothbrushes (0.9 ± 0.2 N), which were not significantly different from each other. Brushing force prior and after instruction of the brushing technique was not significantly different. The manual toothbrush caused highest abrasion of sound and eroded dentin, but lowest on sound enamel. No significant differences were detected on eroded enamel. Brushing forces of manual and sonic toothbrushes are different and affect their abrasive capacity. Patients with severe tooth wear and exposed and/or eroded dentin surfaces should use sonic toothbrushes to reduce abrasion, while patients without tooth wear or with erosive lesions confining only to enamel do not benefit from sonic toothbrushes with regard to abrasion.

Rates of Eolian Rock Abrasion in the Ice-Free Valleys, Antarctica

NASA Astrophysics Data System (ADS)

Hallet, B.; Malin, M. C.; Sletten, R. S.

2016-12-01

Eolian abrasion is a principal surface process in dry regions of Earth and Mars and there is evidence for wind processes active on Venus and Titan. Rock abrasion also has practical significance in diverse fields ranging from preservation of cultural material (artifacts, monuments) to damage of solar panels and windshields in arid regions. Despite its scientific and practical importance, and there have ben only few studies that define rates of rock abrasion quantitatively under natural conditions. Herein we report abrasion rates that have been exceptionally well characterized through a unique long-term (30+-year) field experiment in the ice-free McMurdo Dry Valleys, Antarctica. In 1983 and 1984, over 5000 rock targets of several lithologies (25.4 mm-diameter and 5 mm-thick disks of dolerite, basalt, tuff and sandstone) were installed at five heights (7,14, 21, 35, and 70 cm) facing the 4 cardinal directions at 10 locations (one additional site contains fewer targets). Sequential collections of rock targets exposed to abrasion enable definition of mass loss after 1, 5, 10, 30 and 31 years of exposure; the latter were retrieved during the 2014-2015 season. The abrasion rates generally show striking consistency for each lithology at any site; the multiple targets permit definition of intrinsic differences in mass loss. The rates vary considerably from site to site owing to differences in availability of transportable sediment, wind regime, and surface roughness, and at each site, owing to target orientation relative to the dominant winds and, secondarily, to height above the ground. For the hardest targets, basalt and dolerite, mass loss in 30+ years ranged from essentially zero at some sites to 1/3 of the deployed mass (2.59 g; equivalent to a rock thickness >1.8 mm) where abrasion was most active (Site 7, Central Wright Valley). The tuff targets showed the greatest mass loss, and in many cases were entirely abraded away by the end of the experiment.Current work is

Kinetic energy density and agglomerate abrasion rate during blending of agglomerates into powders.

PubMed

Willemsz, Tofan A; Hooijmaijers, Ricardo; Rubingh, Carina M; Tran, Thanh N; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

2012-01-23

Problems related to the blending of a cohesive powder with a free flowing bulk powder are frequently encountered in the pharmaceutical industry. The cohesive powder often forms lumps or agglomerates which are not dispersed during the mixing process and are therefore detrimental to blend uniformity. Achieving sufficient blend uniformity requires that the blending conditions are able to break up agglomerates, which is often an abrasion process. This study was based on the assumption that the abrasion rate of agglomerates determines the required blending time. It is shown that the kinetic energy density of the moving powder bed is a relevant parameter which correlates with the abrasion rate of agglomerates. However, aspects related to the strength of agglomerates should also be considered. For this reason the Stokes abrasion number (St(Abr)) has been defined. This parameter describes the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. The St(Abr) number is shown to predict the abrasion potential of agglomerates in the dry-mixing process. It appeared possible to include effects of filler particle size and impeller rotational rate into this concept. A clear relationship between abrasion rate of agglomerates and the value of St(Abr) was demonstrated. Copyright © 2011 Elsevier B.V. All rights reserved.

Stem cells in dentistry--review of literature.

PubMed

Dziubińska, P; Jaskólska, M; Przyborowska, P; Adamiak, Z

2013-01-01

Stem cells have been successfully isolated from a variety of human and animal tissues, including dental pulp. This achievement marks progress in regenerative dentistry. This article reviews the latest improvements made in regenerative dental medicine with the involvement of stem cells. Although, various types of multipotent somatic cells can be applied in dentistry, two types of cells have been investigated in this review. Dental pulp cells are classified as: DPSCs, SCAPs and SHEDs.The third group includes two types of cell associated with the periodontium: PDL and DFPC. This review aims to systematize basic knowledge about cellular engineering in dentistry.

Aeolian abrasion on Venus: Preliminary results from the Venus simulator

NASA Technical Reports Server (NTRS)

Marshall, J. R.; Greeley, Ronald; Tucker, D. W.; Pollack, J. B.

1987-01-01

The role of atmospheric pressure on aeolian abrasion was examined in the Venus Simulator with a constant temperature of 737 K. Both the rock target and the impactor were fine-grained basalt. The impactor was a 3 mm diameter angular particle chosen to represent a size of material that is entrainable by the dense Venusian atmosphere and potentially abrasive by virtue of its mass. It was projected at the target 10 to the 5 power times at a velocity of 0.7 m/s. The impactor showed a weight loss of approximately 1.2 x 10 to the -9 power gm per impact with the attrition occurring only at the edges. Results from scanning electron microscope analysis, profilometry, and weight measurement are summarized. It is concluded that particles can incur abrasion at Venusian temperatures even with low impact velocities expected for Venus.

Photodynamic therapy in dentistry: a literature review.

PubMed

Gursoy, Hare; Ozcakir-Tomruk, Ceyda; Tanalp, Jale; Yilmaz, Selçuk

2013-05-01

The purpose of this review was to summarize recent developments regarding photodynamic therapy (PDT) in the field of dentistry. A review of pertinent literature was carried out in PubMED to determine the current position of PDT applications in dentistry. One hundred thirteen relevant articles were retrieved from PubMED by inserting the keywords "photodynamic therapy", "dentistry", "periodontology", "oral surgery", and "endodontics". It is anticipated that this overview will create a specific picture in the practitioner's mind regarding the current status and use of PDT. In spite of different results and suggestions brought about by different researchers, PDT can be considered as a promising and less invasive technique in dentistry. PDT seems to be an effective tool in the treatment of localized and superficial infections. Within the limitations of the present review, it can be concluded that although PDT cannot replace antimicrobial therapy at its current stage, it may be used as an adjunctive tool for facilitating the treatment of oral infections. Oral infections (such as mucosal and endodontic infections, periodontal diseases, caries, and peri-implantitis) are among the specific targets where PDT can be applied. Further long-term clinical studies are necessary in establishing a more specific place of the technique in the field of dentistry.

Biomaterials in Relation to Dentistry.

PubMed

Deb, Sanjukta; Chana, Simran

2015-01-01

Dental caries remains a challenge in the improvement of oral health. It is the most common and widespread biofilm-dependent oral disease, resulting in the destruction of tooth structure by the acidic attack from cariogenic bacteria. The tooth is a heavily mineralised tissue, and both enamel and dentine can undergo demineralisation due to trauma or dietary conditions. The adult population worldwide affected by dental caries is enormous and despite significant advances in caries prevention and tooth restoration, treatments continue to pose a substantial burden to healthcare. Biomaterials play a vital role in the restoration of the diseased or damaged tooth structure and, despite providing reasonable outcomes, there are some concerns with clinical performance. Amalgam, the silver grey biomaterial that has been widely used as a restorative material in dentistry, is currently in throes of being phased out, especially with the Minimata convention and treaty being signed by a number of countries (January 2013; http://mercuryconvention.org/Convention/) that aims to control the anthropogenic release of mercury in the environment, which naturally impacts the use of amalgam, where mercury is a component. Thus, the development of alternative restoratives and restoration methods that are inexpensive, can be used under different climatic conditions, withstand storage and allow easy handling, the main prerequisites of dental biomaterials, is important. The potential for using biologically engineered tissue and consequent research to replace damaged tissues has also seen a quantum leap in the last decade. Ongoing research in regenerative treatments in dentistry includes alveolar ridge augmentation, bone tissue engineering and periodontal ligament replacement, and a future aim is bioengineering of the whole tooth. Research towards developing bioengineered teeth is well underway and identification of adult stem cell sources to make this a viable treatment is advancing; however, this

Evidence-based dentistry on laser paediatric dentistry: review and outlook.

PubMed

Olivi, G; Genovese, M D; Caprioglio, C

2009-03-01

The goal of paediatric dentistry is to provide preventive education to parents and patients as well as interception and therapy of dental diseases in a minimally invasive way using a stress-free approach. Different laser wavelengths are used for different applications following these minimally invasive concepts: argon, KTP, diode, Nd:YAG, and CO2 lasers are used for soft tissue applications and the erbium family is used for both soft and hard tissue procedures. This paper offers a revision and a discussion of the international literature, showing also some clinical procedures. related to these scientific studies. Soft tissues laser applications in Pediatric Dentistry include application in oral surgery as well as in periodontics and orthodontics. Laser applications on hard tissues include caries prevention and detection and application for sealing of pits and fissures. Also application for cavity preparation, carious removal and pulp therapy are discussed.

Collaboration Between Dietetics and Dentistry: Dietetic Internship in Pediatric Dentistry

PubMed Central

More, Frederick G.; Sasson, Lisa M.; Godfrey, Emilie M.; Sehl, Rima B.

2006-01-01

The American Dietetic Association and the American Dental Association share a common interest in improving the health and quality of life of the population. Dental visits present an opportunity to identify nutrition-related issues for both the pediatric and adult population. Traditionally, dental and nutrition students have had little opportunity to learn and work together since little time was spent on nutrition in the dental curriculum. The purpose of this article is to describe the development of a new collaborative training experience for dietetic interns and pediatric dentistry residents. The oral health rotation for dietetic interns also has several objectives, including experience interacting with a culturally diverse population and participating in community nutrition education (Head Start). In its first 18 months, the collaborative program has been viewed as a success by the pediatric dentistry faculty and residents and the nutrition faculty and interns. PMID:16639470

Relationships Between Abrasive Wear, Hardness, and Surface Grinding Characteristics of Titanium-Based Metal Matrix Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blau, Peter Julian; Jolly, Brian C

2009-01-01

The objective of this work was to support the development of grinding models for titanium metal-matrix composites (MMCs) by investigating possible relationships between their indentation hardness, low-stress belt abrasion, high-stress belt abrasion, and the surface grinding characteristics. Three Ti-based particulate composites were tested and compared with the popular titanium alloy Ti-6Al-4V. The three composites were a Ti-6Al-4V-based MMC with 5% TiB{sub 2} particles, a Ti-6Al-4V MMC with 10% TiC particles, and a Ti-6Al-4V/Ti-7.5%W binary alloy matrix that contained 7.5% TiC particles. Two types of belt abrasion tests were used: (a) a modified ASTM G164 low-stress loop abrasion test, and (b)more » a higher-stress test developed to quantify the grindability of ceramics. Results were correlated with G-ratios (ratio of stock removed to abrasives consumed) obtained from an instrumented surface grinder. Brinell hardness correlated better with abrasion characteristics than microindentation or scratch hardness. Wear volumes from low-stress and high-stress abrasive belt tests were related by a second-degree polynomial. Grindability numbers correlated with hard particle content but were also matrix-dependent.« less

Laser restorative dentistry in children and adolescents.

PubMed

Olivi, G; Genovese, M D

2011-04-01

The idea of substituting a drill with a laser light, has led to its introduction in dentistry. Besides being more accepted to patients, in paediatric dentistry the laser has demonstrated safety compared with rotating instruments. A review of the past 20 years of the dental literature concerning laser use in dentistry, including paediatric dentistry was completed. The findings of that review are presented. The various types of lasers and their uses for caries detection, tooth sealing and caries removal are described. Laser caries detection demonstrated a good reproducibility, reliability and predictability to monitor the caries process over time. Erbium lasers have been found to be efficient for caries removal, tooth cleaning and decontamination. The laser erbium technology represents a safe device to effectively and selectively remove carious tissues from decayed teeth. For children, all the recognized advantages of this technique play a decisive role in the successful day-to-day treatment of dental caries.

Advances in Nanotechnology for Restorative Dentistry.

PubMed

Khurshid, Zohaib; Zafar, Muhammad; Qasim, Saad; Shahab, Sana; Naseem, Mustafa; AbuReqaiba, Ammar

2015-02-16

Rationalizing has become a new trend in the world of science and technology. Nanotechnology has ascended to become one of the most favorable technologies, and one which will change the application of materials in different fields. The quality of dental biomaterials has been improved by the emergence of nanotechnology. This technology manufactures materials with much better properties or by improving the properties of existing materials. The science of nanotechnology has become the most popular area of research, currently covering a broad range of applications in dentistry. This review describes the basic concept of nanomaterials, recent innovations in nanomaterials and their applications in restorative dentistry. Advances in nanotechnologies are paving the future of dentistry, and there are a plenty of hopes placed on nanomaterials in terms of improving the health care of dental patients.

Advances in Nanotechnology for Restorative Dentistry

PubMed Central

Khurshid, Zohaib; Zafar, Muhammad; Qasim, Saad; Shahab, Sana; Naseem, Mustafa; AbuReqaiba, Ammar

2015-01-01

Rationalizing has become a new trend in the world of science and technology. Nanotechnology has ascended to become one of the most favorable technologies, and one which will change the application of materials in different fields. The quality of dental biomaterials has been improved by the emergence of nanotechnology. This technology manufactures materials with much better properties or by improving the properties of existing materials. The science of nanotechnology has become the most popular area of research, currently covering a broad range of applications in dentistry. This review describes the basic concept of nanomaterials, recent innovations in nanomaterials and their applications in restorative dentistry. Advances in nanotechnologies are paving the future of dentistry, and there are a plenty of hopes placed on nanomaterials in terms of improving the health care of dental patients. PMID:28787967

Microbiological contamination of compressed air used in dentistry: an investigation.

PubMed

Conte, M; Lynch, R M; Robson, M G

2001-11-01

The purpose of this preliminary investigation was twofold: 1) to examine the possibility of cross-contamination between a dental-evacuation system and the compressed air used in dental operatories and 2) to capture and identify the most common microflora in the compressed-air supply. The investigation used swab, water, and air sampling that was designed to track microorganisms from the evacuation system, through the air of the mechanical room, into the compressed-air system, and back to the patient. Samples taken in the vacuum system, the air space in the mechanical room, and the compressed-air storage tank had significantly higher total concentrations of bacteria than the outside air sampled. Samples of the compressed air returning to the operatory were found to match the outside air sample in total bacteria. It was concluded that the air dryer may have played a significant role in the elimination of microorganisms from the dental compressed-air supply.

Method of protecting surfaces from abrasion and abrasion resistant articles of manufacture

DOEpatents

Hirschfeld, T.B.

1988-06-09

Surfaces of fabricated structures are protected from damage by impacting particulates by a coating of hard material formed as a mass of thin flexible filaments having root ends secured to the surface and free portions which can flex and overlap to form a resilient cushioning mat which resembles hair or fur. The filamentary coating covers the underlying surface with hard abrasion resistance material while also being compliant and capable of local accommodation to particle impacts. The coating can also function as thermal and/or acoustical insulation and has a friction reducing effect. 11 figs.

Abrasion Testing of Candidate Outer Layer Fabrics for Lunar EVA Space Suits

NASA Technical Reports Server (NTRS)

Mitchell, Kathryn

2009-01-01

During the Apollo program, the space suit outer layer fabrics were severely abraded after just a few Extravehicular Activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots, which penetrated the outer layer fabric into the thermal protection layers after less than eight hours of surface operations. Current plans for the Constellation Space Suit Element require the space suits to support hundreds of hours of EVA on the Lunar surface, creating a challenge for space suit designers to utilize materials advances made over the last forty years and improve upon the space suit fabrics used in the Apollo program. A test methodology has been developed by the NASA Johnson Space Center Crew and Thermal Systems Division for establishing comparative abrasion wear characteristics between various candidate space suit outer layer fabrics. The abrasion test method incorporates a large rotary drum tumbler with rocks and loose lunar simulant material to induce abrasion in fabric test cylinder elements, representative of what might occur during long term planetary surface EVAs. Preliminary materials screening activities were conducted to determine the degree of wear on representative space suit outer layer materials and the corresponding dust permeation encountered between subsequent sub-layers of thermal protective materials when exposed to a simulated worst case eight hour EVA. The test method was used to provide a preliminary evaluation of four candidate outer layer fabrics for future planetary surface space suit applications. This paper provides a review of previous abrasion studies on space suit fabrics, details the methodologies used for abrasion testing in this particular study, shares the results of the testing, and provides recommendations for future work.

Abrasion Testing of Candidate Outer Layer Fabrics for Lunar EVA Space Suits

NASA Technical Reports Server (NTRS)

Mitchell, Kathryn C.

2010-01-01

During the Apollo program, the space suit outer layer fabrics were badly abraded after just a few Extravehicular Activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots, which penetrated the outer layer fabric into the thermal protection layers after less than eight hours of surface operations. Current plans for the Constellation Space Suit Element require the space suits to support hundreds of hours of EVA on the Lunar surface, creating a challenge for space suit designers to utilize materials advances made over the last forty years and improve upon the space suit fabrics used in the Apollo program. A test methodology has been developed by the NASA Johnson Space Center Crew and Thermal Systems Division for establishing comparative abrasion wear characteristics between various candidate space suit outer layer fabrics. The abrasion test method incorporates a large rotary drum tumbler with rocks and loose lunar simulant material to induce abrasion in fabric test cylinder elements, representative of what might occur during long term planetary surface EVAs. Preliminary materials screening activities were conducted to determine the degree of wear on representative space suit outer layer materials and the corresponding dust permeation encountered between subsequent sub -layers of thermal protective materials when exposed to a simulated worst case eight hour EVA. The test method was used to provide a preliminary evaluation of four candidate outer layer fabrics for future planetary surface space suit applications. This Paper provides a review of previous abrasion studies on space suit fabrics, details the methodologies used for abrasion testing in this particular study, and shares the results and conclusions of the testing.

Impact of brushing force on abrasion of acid-softened and sound enamel.

PubMed

Wiegand, A; Köwing, L; Attin, T

2007-11-01

The study aimed to analyse the effects of different brushing loads on abrasion of acid-softened and sound enamel surfaces. Sound and acid-softened surfaces of each 10 human enamel samples were submitted to brushing abrasion in an automatic brushing machine at 1.5 N (A), 2.5 N (B), 3.5 N (C) or 4.5 N (D) brushing load. Prior to abrasion, demineralisation of half of each enamel surface was performed by storage in hydrochloric acid (pH 2.0) for 60s. Brushing was carried out (1000 strokes) using a manual toothbrush and toothpaste slurry in a ratio of 1:3. Enamel loss was measured after 10, 20, 50, 100, 150, 200, 250, 300, 350 and 1000 brushing strokes (BS). Pre- and post-brushing values of Knoop indentation length (5 indentations each sample) were measured and mean enamel loss was calculated from the change in indentation depth. Within- and between-group comparisons were performed by ANOVA and t-test followed by Bonferroni-correction. Enamel loss of acid-softened surfaces was significantly influenced by the brushing load applied and was mostly significantly higher in group D (10-1000 BS: 225-462 nm) compared to A (10-1000 BS: 164-384), B (10-1000 BS: 175-370 nm) and C (10-1000 BS: 191-396 nm). Abrasion of acid-softened enamel was fourfold higher compared to sound surfaces. Sound enamel was significantly influenced by the brushing force at 20-200 brushing strokes only, but revealed no significant differences between groups A-D. Brushing load influences abrasion of briefly eroded enamel, but might be of minor importance for abrasion of sound enamel surfaces.

Development of underwater cutting system by abrasive water-jet

NASA Astrophysics Data System (ADS)

Demura, Kenji; Yamaguchi, Hitoshi

1993-09-01

The technology to cut objects in the ocean's depths with abrasive water jets was examined for possible application in view of the greater water depths and sophistication involved in work on the ocean floor today. A test model was developed to study this technology's safety and practicability. The test model was designed for use at great water depths and has functions and a configuration that are unlike equipment used on land. A continuous, stable supply of abrasive is a distinctive design feature. In land applications, there had been problems with plugged tubes and an uneven supply. For this reason, the abrasive was converted to slurry form, and a continuous pressurized tube pump system was adopted for supply to the nozzle head. Also, a hydraulic motor that does not employ oil or electric power was used to provide an underwater drive that is environment-friendly. The report outlines the technology's general design concept including its distinctive functions and its configuration for use at great depths, and the report provides great detail on the equipment.

Tenerife revisited: the critical role of dentistry.

PubMed

Brannon, R B; Morlang, W M

2001-05-01

The authors record the contribution of dentistry to the identification of victims of one of the most significant disasters in the history of aviation-the March 1977 collision of two Boeing 747 jumbo jets in the Canary Islands, which resulted in 583 fatalities. Dental identification was the primary method of victim identification because a high percentage of the bodies were severely burned. Virtually all aspects of the U.S. identification efforts have been reported with the exception of the valuable role of dentistry. The dental team's organization, methodology, and significant contributions to forensic dentistry and a variety of remarkable problems that the team encountered are documented.

Abrasion resistant composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, Keith D; Barnes, Christopher A; Henderson, Stephen L

A surface covering composition of abrasion resistant character adapted for disposition in overlying bonded relation to a metal substrate. The surface covering composition includes metal carbide particles within a metal matrix at a packing factor of not less than about 0.6. Not less than about 40 percent by weight of the metal carbide particles are characterized by an effective diameter in the range of +14-32 mesh prior to introduction to the metal matrix. Not less than about 3 percent by weight of the metal carbide particles are characterized by an effective diameter of +60 mesh prior to introduction to themore » metal matrix.« less

Laser abrasion for cosmetic and medical treatment of facial actinic damage

DOE Office of Scientific and Technical Information (OSTI.GOV)

David, L.M.; Lask, G.P.; Glassberg, E.

1989-06-01

Previous studies have shown the carbon dioxide (CO/sub 2/) laser to be effective in the treatment of actinic cheilitis. After CO/sub 2/ laser abrasion, normal skin and marked cosmetic improvement of the lip were noted. In our study, twenty-three patients were treated with CO/sub 2/ laser abrasions for cosmetic improvement of facial lines and actinic changes. Pre- and postoperative histopathologic examinations were made on two patients. Preoperative examination of specimens from actinically damaged skin showed atypical keratinocytes in the basal layer of the epidermis, with overlying dense compact orthokeratosis and parakeratosis. Abundant solar elastosis was seen in the papillary dermis.more » Postoperative histologic specimens showed a normal-appearing epidermis with fibrosis in the papillary dermis and minimal solar elastosis (about four weeks after laser treatment). At present, various modalities are available for the regeneration of the aged skin, including chemical peels and dermabrasion. Significantly fewer complications were noted with CO/sub 2/ laser abrasion than with these methods. Thus, CO/sub 2/ laser abrasion can be useful in the cosmetic and medical treatment of the aged skin. Marked clinical and histologic improvement has been demonstrated.« less

Release of carbon nanotubes from an epoxy-based nanocomposite during an abrasion process.

PubMed

Schlagenhauf, Lukas; Chu, Bryan T T; Buha, Jelena; Nüesch, Frank; Wang, Jing

2012-07-03

The abrasion behavior of an epoxy/carbon nanotube (CNT) nanocomposite was investigated. An experimental setup has been established to perform abrasion, particle measurement, and collection all in one. The abraded particles were characterized by particle size distribution and by electron microscopy. The abrasion process was carried out with a Taber Abraser, and the released particles were collected by a tube for further investigation. The particle size distributions were measured with a scanning mobility particle sizer (SMPS) and an aerodynamic particle sizer (APS) and revealed four size modes for all measured samples. The mode corresponding to the smallest particle sizes of 300-400 nm was measured with the SMPS and showed a trend of increasing size with increasing nanofiller content. The three measured modes with particle sizes from 0.6 to 2.5 μm, measured with the APS, were similar for all samples. The measured particle concentrations were between 8000 and 20,000 particles/cm(3) for measurements with the SMPS and between 1000 and 3000 particles/cm(3) for measurements with the APS. Imaging by transmission electron microscopy (TEM) revealed that free-standing individual CNTs and agglomerates were emitted during abrasion.

Effect of dried sunflower seeds on incisal edge abrasion: A rare case report.

PubMed

Rath, Avita; Ramamurthy, Priyadarshini H; Fernandes, Bennete Aloysius; Sidhu, Preena

2017-01-01

Tooth surface loss (TSL) is a complex phenomenon characterized by the loss of hard tooth structure at various locations of the teeth, usually due to more than one factor. TSL due to abrasion can be significant in patients consuming coarse, abrasive diet. The present case reports an interesting incisal edge abrasion in a female patient, attributed to a particular dietary behavior of long-term consumption of sunflower seeds. All her family members and most of the people from her native place were also reported to have similar lesions by the patient. Larger epidemiological studies to assess the prevalence and severity of such abrasive lesions in geographic areas with this particular dietary habit need to be carried out so that people may be made aware and educated about alternative ways of eating sunflower seeds that will not cause any form of tooth wear.

Pay for performance: will dentistry follow?

PubMed

Voinea-Griffin, Andreea; Fellows, Jeffrey L; Rindal, Donald B; Barasch, Andrei; Gilbert, Gregg H; Safford, Monika M

2010-04-28

"Pay for performance" is an incentive system that has been gaining acceptance in medicine and is currently being considered for implementation in dentistry. However, it remains unclear whether pay for performance can effect significant and lasting changes in provider behavior and quality of care. Provider acceptance will likely increase if pay for performance programs reward true quality. Therefore, we adopted a quality-oriented approach in reviewing those factors which could influence whether it will be embraced by the dental profession. The factors contributing to the adoption of value-based purchasing were categorized according to the Donabedian quality of care framework. We identified the dental insurance market, the dental profession position, the organization of dental practice, and the dental patient involvement as structural factors influencing the way dental care is practiced and paid for. After considering variations in dental care and the early stage of development for evidence-based dentistry, the scarcity of outcome indicators, lack of clinical markers, inconsistent use of diagnostic codes and scarcity of electronic dental records, we concluded that, for pay for performance programs to be successfully implemented in dentistry, the dental profession and health services researchers should: 1) expand the knowledge base; 2) increase considerably evidence-based clinical guidelines; and 3) create evidence-based performance measures tied to existing clinical practice guidelines. In this paper, we explored factors that would influence the adoption of value-based purchasing programs in dentistry. Although none of these factors were essential deterrents for the implementation of pay for performance programs in medicine, the aggregate seems to indicate that significant changes are needed before this type of program could be considered a realistic option in dentistry.

Research on operation mode of abrasive grain during grinding

NASA Astrophysics Data System (ADS)

Ivanova, T. N.; Dement’ev, V. B.; Nikitina, O. V.

2018-03-01

The processing of materials by cutting with an abrasive tool is carried out by means of thousands of grains bonded together as a single whole. The quality of the abrasive tool is defined by cutting properties of abrasive grains and depends on features of spreading the temperature field in time and in the abrasive grain volume. Grains are exposed to heating and cooling during work. It leads to undesired effects such as a decrease of durability of grain retention in the binder, hardness, intensification of diffusion and oxidation processes between the binder and the grain, the occurrence of considerable temperature stresses in the grain itself. The obtained equation which allows calculation of temperature field of grain for one rotation of grinding wheel shows that the temperature of the wheel depends on grinding modes and thermophysical properties of abrasive material. Thus, as the time of contact of grain with processed material increases, the temperature in the cutting area rises. As thermophysical properties increase, the temperature in cutting area decreases. Thermal working conditions are determined to be different from each other depending on contact time of the grain and the material. For example, in case of creep-feed grinding, the peak value of temperature is higher than during multistep grinding; the depth of expansion is greater. While the speed of the thermal process in creep-feed grinding is 2-3 times lower than in multistep grinding, the gradient reduces 3-4 times. The analysis of machining methods shows that creep-feed grinding ensures greater depth of grain heating, a smaller heating rate and a reduced velocity gradient. It causes a decrease of probable allotropic modifications and prevents from occurring of heat strokes - cracking of grains due to high temperature falls. Consequently, it is necessary to employ creep-feed grinding to increase the efficiency of abrasive tool employing. Three operation modes of grinding wheel including blunting, full

Influence of different air-abrasive powders on cell viability at biologically contaminated titanium dental implants surfaces.

PubMed

Schwarz, Frank; Ferrari, Daniel; Popovski, Kristian; Hartig, Brigitte; Becker, Jürgen

2009-01-01

Studies have indicated that oral biofilm formation at structured titanium surfaces interferes with cell adhesion and proliferation, and its removal by means of conventional treatment procedures may not be sufficient to render these surfaces biologically acceptable. Therefore, the aim of the study was to evaluate the influence of different air-abrasive powders on cell viability at biologically contaminated titanium dental implant surfaces. Intraoral splints were used to collect an in vivo biofilm on sandblasted and acid-etched titanium discs for 48 h. A single (1x) and repeated (2x) use of four different powders (amino acid glycine or sodium bicarbonate particles; range of mean particle size (d(v50)):20-75 microm) was applied at two distances (1 and 2 mm) and angles (30 degrees and 90 degrees) to the surfaces. Specimens (2x) were incubated with SaOs-2 cells for 7 days. Residual biofilm (RB) areas (%), and surface alterations (SEM) (1x and 2x), as well as SaOs-2 cell viability, expressed as mitochondrial cell activity (MA) (counts/second) (2x specimens), were assessed. Comparable mean RB areas were observed within and between groups after both 1x (RB: 0.0% +/- 0.0% to 5.7% +/- 5.7%) and 2x (RB: 0.0% +/- 0.0%) treatments. All surface treatments did not lead to MA (2x) values comparable to the sterile control group. However, sodium bicarbonate particles resulted in significantly higher MA (2x) values than amino acid glycine powders of different sizes. This was associated with pronounced alterations of the surface morphology (2x). Within the limits of the present study, it was concluded that SaOs-2 cell viability at biologically contaminated titanium surfaces was mainly influenced by the particle type of the powder. (c) 2008 Wiley Periodicals, Inc.

Evidence-Based Dentistry in Everyday Practice.

PubMed

Gudray, Kiran; Walmsley, Anthony Damien

2016-12-01

This article informs readers of a method of implementing evidence-based dentistry in practice. Following these steps, practitioners should be able to use this skill in an efficient manner. The importance of evidence-based dentistry and its relevance to situations encountered in everyday practice is also highlighted. Clinical relevance: This article highlights a series of steps to be followed by practitioners to ensure that treatment provided is supported by the most recent, good quality evidence.

Prepolishing on a CNC platform with bound abrasive contour tools

NASA Astrophysics Data System (ADS)

Schoeffler, Adrienne E.; Gregg, Leslie L.; Schoen, John M.; Fess, Edward M.; Hakiel, Michael; Jacobs, Stephen D.

2003-05-01

Deterministic microgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-5μm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an Optipro CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Special care dentistry for general dental practice.

PubMed

Greig, Vicki; Sweeney, Petrina

2013-01-01

Although special care dentistry (SCD) is a fairly recent specialty, the principles and practice of SCD have been developed since the 1980s. Shared care of these patients with general dental practitioners remains vital to ensure that comprehensive care is provided. This article aims to discuss some of the patient groups commonly seen in SCD clinics and give an insight into the varied complex medical and social aspects of care which are managed as part of providing appropriate, safe and holistic care. Many patients who currently fall under the remit of special care dentistry could be treated safely in general dental practice. This article acts as an introduction to special care dentistry for general dental practitioners.

Augmented reality in dentistry: a current perspective.

PubMed

Kwon, Ho-Beom; Park, Young-Seok; Han, Jung-Suk

2018-02-21

Augmentation reality technology offers virtual information in addition to that of the real environment and thus opens new possibilities in various fields. The medical applications of augmentation reality are generally concentrated on surgery types, including neurosurgery, laparoscopic surgery and plastic surgery. Augmentation reality technology is also widely used in medical education and training. In dentistry, oral and maxillofacial surgery is the primary area of use, where dental implant placement and orthognathic surgery are the most frequent applications. Recent technological advancements are enabling new applications of restorative dentistry, orthodontics and endodontics. This review briefly summarizes the history, definitions, features, and components of augmented reality technology and discusses its applications and future perspectives in dentistry.

Development of a two-body wet abrasion test method with attention to the effects of reused abradant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blau, Peter Julian; Dehoff, Ryan R

2012-01-01

Abrasive wear is among the most common and costliest causes for material wastage, and it occurs in many forms. A simple method has been developed to quantify the response of metals and alloys to two-body wet abrasion. A metallographic polishing machine was modified to create a disk-on-flat sliding test rig. Adhesive-backed SiC grinding papers were used under fixed load and speed to rank the abrasive wear of seven alloy steels, some of which are candidates for drill cones for geothermal drilling. Standardized two-body abrasion tests, like those described in ASTM G132, feed unused abrasive into the contact; however, the currentmore » work investigated whether useful rankings could still be obtained with a simpler testing configuration in which specimens repeatedly slide on the same wear path under water-lubricated conditions. Tests using abrasive grit sizes of 120 and 180 resulted in the same relative ranking of the alloys although the coarser grit produced more total wear. Wear decreased when the same abrasive disk was re-used for up to five runs, but the relative rankings of the steels remained the same. This procedure was presented to ASTM Committee G2 on Wear and Erosion as a potential standard test for wet two-body abrasive wear.« less

New vibration-assisted magnetic abrasive polishing (VAMAP) method for microstructured surface finishing.

PubMed

Guo, Jiang; Kum, Chun Wai; Au, Ka Hing; Tan, Zhi'En Eddie; Wu, Hu; Liu, Kui

2016-06-13

In order to polish microstructured surface without deteriorating its profile, we propose a new vibration-assisted magnetic abrasive polishing (VAMAP) method. In this method, magnetic force guarantees that the magnetic abrasives can well contact the microstructured surface and access the corners of microstructures while vibration produces a relative movement between microstructures and magnetic abrasives. As the vibration direction is parallel to the microstructures, the profile of the microstructures will not be deteriorated. The relation between vibration and magnetic force was analyzed and the feasibility of this method was experimentally verified. The results show that after polishing, the surface finish around microstructures was significantly improved while the profile of microstructures was well maintained.

A systematic review of the uses of fluoroscopy in dentistry.

PubMed

Uzbelger Feldman, Daniel; Yang, Jie; Susin, Cristiano

2010-01-01

To determine the quality of the evidence for the uses of fluoroscopy in dentistry. A systematic review using Ovid and MEDLINE was conducted to identify papers showing the uses of fluoroscopy in dentistry published between 1953 and September 2009. Human, animal and phantom/skull/mannequin studies on fluoroscopy with regard to its diagnostic value, research performance, and clinical and safety applications in dentistry were included in this analysis. Studies that were not in English, as well as those that employed fluoroscopy in dentistry without the use of image intensification, were excluded. Articles were evaluated, classified and graded by levels of evidence. Fifty-five out of 139 papers fulfilled the inclusion criteria. Amongst them, 19 were related to diagnosis, 15 to research, 12 to clinical and nine to safety applications. Fluoroscopy has contributed to nine different areas of dentistry. Also, it was used on 895 dental patients, 37 animals and 17 phantoms/skulls/mannequins. Two randomised controlled trials, two cohort studies, two case controls, 48 case reports and one expert opinion were found. Fluoroscopy with image intensification has been a useful, but not consistently used tool in dentistry for over 50 years. Several lines of evidence have shown fluoroscopy's diagnostic potential, research use, and clinical and safety applications in dentistry.

A Study on Postmortem Wound Dating by Gross and Histopathological Examination of Abrasions.

PubMed

Vinay, Javaregowda; Harish, Sathyanarayana; Mangala, Gouri S R; Hugar, Basappa S

2017-06-01

Abrasions are the most common blunt force injuries. The precise dating of injury is extremely important in forensic medicine practice. As we know, the wound healing occurs in well-orchestrated sequence, consisting of inflammation, proliferation, and maturation.A study of occurrence of such phases will help in understanding the sequence of events in wound healing. In this context, this study of wound dating from gross and microscopic level was taken. Postmortem study of wound dating by gross and histopathological examination of abrasions was carried out in the Department of Forensic Medicine, in M.S. Ramaiah Medical College. A total of 101 abrasions were correlated to time frame the occurrence of different gross changes and microscopic changes that follow the blunt trauma. Abrasions ranging from 0 hour to a maximum of 45 days were studied. The gross changes of abrasions were in correlation with the microscopic changes; however, the role of the comorbid conditions is significant because the results showed variations with respect to healing process. This study signifies that, if naked eye examination is studied along with histopathological examination, the reliability and accuracy of dating of wound increase. Whenever accurate determination of age is required, the autopsy surgeon can subject the samples for histopathological examination and correlate before opining the age of injury.

Exploring leadership in the context of dentistry in the UK.

PubMed

Willcocks, Stephen George

2016-05-03

Purpose The purpose of this paper is to explore selective leadership approaches in the context of dentistry in the UK. Design/methodology/approach This is a conceptual paper utilising published sources from relevant literature about leadership theory and practice and the policy background to dentistry in the UK. Findings This paper suggests that there is merit in identifying and applying an eclectic mix of leadership theory to the case of dentistry. It offers insight into individual aspects of the leadership role for dentists and applies this to the dental context. It also contrasts these individual approaches with shared leadership and suggests this may also be relevant to dentistry. It highlights the fact that leadership will be of growing concern for dentistry in the light of recent policy changes. Research limitations/implications This paper points out that there are developmental implications depending on the particular approach taken. It argues that leadership development will become increasingly important in dentistry in the UK. Originality/value This paper addresses a topic that has so far received limited attention in the literature.

Effect of ceramic coating by aerosol deposition on abrasion resistance of a resin composite material.

PubMed

Taira, Yohsuke; Hatono, Hironori; Mizukane, Masahiro; Tokita, Masahiro; Atsuta, Mitsuru

2006-12-01

Aerosol deposition (AD coating) is a novel technique to coat solid substances with a ceramic film. The purpose of the present study was to investigate the effect of AD coating on abrasion resistance of a resin composite material. A 5-microm-thick aluminum oxide layer was created on the polymerized resin composite. The specimen was cyclically abraded using a toothbrush abrasion simulator for 100,000 cycles. Abraded surface was then measured with a profilometer to determine the average roughness (Ra) and maximum roughness (Rmax). It was found that abrasion cycling increased the Ra value of the No-AD-coating group, but decreased the Ra and Rmax values of the AD coating group. Moreover, the AD coating group showed significantly smaller Ra and Rmax values after 100,000 abrasion cycles as compared to the No-coating control group. Microscopic observation supported these findings. In conclusion, the resistance of the resin composite against toothbrush abrasion was improved by AD coating.

Finishing of display glass for mobile electronics using 3M Trizact diamond tile abrasive pads

NASA Astrophysics Data System (ADS)

Zheng, Lianbin; Fletcher, Tim; Na, Tee Koon; Sventek, Bruce; Romero, Vince; Lugg, Paul S.; Kim, Don

2010-10-01

This paper will describe a new method being used during the finishing of glass displays for mobile electronics including mobile hand held devices and notebook computers. The new method consists of using 3M TrizactTM Diamond Tile Abrasive Pads. TrizactTM Diamond Tile is a structured fixed abrasive grinding technology developed by 3M Company. The TrizactTM Diamond Tile structured abrasive pad consists of an organic (polymeric binder) - inorganic (abrasive mineral, i.e., diamond) composite that is used with a water-based coolant. TrizactTM Diamond Tile technology can be applied in both double and single side grinding applications. A unique advantage of TrizactTM Diamond Tile technology is the combination of high stock removal and low sub-surface damage. Grinding results will be presented for both 9 micron and 20 micron grades of TrizactTM Diamond Tile abrasive pads used to finish several common display glasses including Corning GorillaTM glass and Soda Lime glass.

Review of Artificial Abrasion Test Methods for PV Module Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, David C.; Muller, Matt T.; Simpson, Lin J.

This review is intended to identify the method or methods--and the basic details of those methods--that might be used to develop an artificial abrasion test. Methods used in the PV literature were compared with their closest implementation in existing standards. Also, meetings of the International PV Quality Assurance Task Force Task Group 12-3 (TG12-3, which is concerned with coated glass) were used to identify established test methods. Feedback from the group, which included many of the authors from the PV literature, included insights not explored within the literature itself. The combined experience and examples from the literature are intended tomore » provide an assessment of the present industry practices and an informed path forward. Recommendations toward artificial abrasion test methods are then identified based on the experiences in the literature and feedback from the PV community. The review here is strictly focused on abrasion. Assessment methods, including optical performance (e.g., transmittance or reflectance), surface energy, and verification of chemical composition were not examined. Methods of artificially soiling PV modules or other specimens were not examined. The weathering of artificial or naturally soiled specimens (which may ultimately include combined temperature and humidity, thermal cycling and ultraviolet light) were also not examined. A sense of the purpose or application of an abrasion test method within the PV industry should, however, be evident from the literature.« less

Wheel Abrasion Experiment Metals Selection for Mars Pathfinder Mission

NASA Technical Reports Server (NTRS)

Hepp, Aloysius F.; Fatemi, Navid S.; Wilt, David M.; Ferguson, Dale C.; Hoffman, Richard; Hill, Maria M.; Kaloyeros, Alain E.

1996-01-01

A series of metals was examined for suitability for the Wheel Abrasion Experiment, one of ten microrover experiments of the Mars Pathfinder Mission. The seven candidate metals were: Ag, Al, Au, Cu, Ni, Pt, and W. Thin films of candidate metals from 0.1 to 1.0 micrometer thick were deposited on black anodized aluminum coupons by e-beam and resistive evaporation and chemical vapor deposition. Optical, corrosion, abrasion, and adhesion criteria were used to select Al, Ni, and Pt. A description is given of the deposition and testing of thin films, followed by a presentation of experimental data and a brief discussion of follow-on testing and flight qualification.

Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

NASA Technical Reports Server (NTRS)

Street, Kenneth W., Jr.; Kobrick, Ryan L.; Klaus, David M.

2013-01-01

Abrasion of mechanical components and fabrics by soil on Earth is typically minimized by the effects of atmosphere and water. Potentially abrasive particles lose sharp and pointed geometrical features through erosion. In environments where such erosion does not exist, such as the vacuum of the Moon, particles retain sharp geometries associated with fracturing of their parent particles by micrometeorite impacts. The relationship between hardness of the abrasive and that of the material being abraded is well understood, such that the abrasive ability of a material can be estimated as a function of the ratio of the hardness of the two interacting materials. Knowing the abrasive nature of an environment (abrasive)/construction material is crucial to designing durable equipment for use in such surroundings. The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width. The ZOI has been found to be at least twice the size of a standard width measurement; in some cases, considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for de tailed analysis. Documenting additional changes to various surface roughness par ameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Further - more, by investigating the use of custom scratch tips for specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized

Paediatric laser dentistry. Part 1: General introduction.

PubMed

Caprioglio, C; Olivi, G; Genovese, M D

2017-03-01

Knowledge of the physical characteristics of different laser lights and optical and thermal properties of oral tissues is very important to understand the interaction of dental lasers with biological tissues. Choosing the correct dental laser is crucial to match specific wavelengths with target chromophores of different tissues; this affinity makes laser irradiation selective and therefore minimally invasive. Various types of lasers are used in dentistry, offering a viable alternative to low and high-speed handpieces and surgical blades, and also minimising fear and discomfort of the patient. Lasers can provide innovative and minimally invasive therapies in different branches of dentistry including preventive and restorative dentistry, traumatic injury treatments and surgical procedures. Laser has also biostimulating and anti-inflammatory effects, as well as analgesic effect.

Robotic edge machining using elastic abrasive tool

NASA Astrophysics Data System (ADS)

Sidorova, A. V.; Semyonov, E. N.; Belomestnykh, A. S.

2018-03-01

The article describes a robotic center designed for automation of finishing operations, and analyzes technological aspects of an elastic abrasive tool applied for edge machining. Based on the experimental studies, practical recommendations on the application of the robotic center for finishing operations were developed.

Historical Perspectives on the Use of Microscopes in Dentistry.

PubMed

Gutmann, James L

2017-01-01

The use of microscopes in dentistry has become quite popular since the late 1980s. However, its origin for dental applications can be traced to the early 20th century, when a microscope, invented by an American biologist named Greenough, working in the Zeiss Company, was adapted for use in dentistry. Initially it had been used in botany, metallurgy, and zoology, in addition to revolutionizing the study of coral and entomology. Copyright American Academy of the History of Dentistry.

Predoctoral Teaching of Geriatric Dentistry in U.S. Dental Schools.

PubMed

Ettinger, Ronald L; Goettsche, Zachary S; Qian, Fang

2017-08-01

The aim of this study was to assess the current teaching of geriatric dentistry in U.S. dental schools and compare the findings to previous reports. Academic deans at all 67 U.S. dental schools were contacted in November 2015 via email, asking them to complete a questionnaire about the teaching of geriatric dentistry or gerodontology at their institution. Questionnaires were received from 56 of the 67 schools (84% response rate). The results showed that geriatric dentistry was taught in all responding schools; for 92.8% of the respondents, the instruction was compulsory. Among the responding schools, 62.5% were teaching it as an independent course, 25% as an organized series of lectures, and 8.9% as occasional lectures in parts of other courses. In addition, 57.1% had some form of compulsory clinical education in geriatric dentistry. Public schools, as opposed to private schools, were marginally associated with an increased interest in expanding geriatric dentistry teaching (p=0.078). No differences were found between any teaching variables and school location. This study found that the form of education in geriatric dentistry in U.S. dental schools differed in many ways, but the teaching of geriatric dentistry had increased among all respondents and had been increasing for over 30 years. Future research is needed to determine the impact of this teaching on services to the geriatric community.

Tissue engineering in dentistry.

PubMed

Abou Neel, Ensanya Ali; Chrzanowski, Wojciech; Salih, Vehid M; Kim, Hae-Won; Knowles, Jonathan C

2014-08-01

of this review is to inform practitioners with the most updated information on tissue engineering and its potential applications in dentistry. The authors used "PUBMED" to find relevant literature written in English and published from the beginning of tissue engineering until today. A combination of keywords was used as the search terms e.g., "tissue engineering", "approaches", "strategies" "dentistry", "dental stem cells", "dentino-pulp complex", "guided tissue regeneration", "whole tooth", "TMJ", "condyle", "salivary glands", and "oral mucosa". Abstracts and full text articles were used to identify causes of craniofacial tissue loss, different approaches for craniofacial reconstructions, how the tissue engineering emerges, different strategies of tissue engineering, biomaterials employed for this purpose, the major attempts to engineer different dental structures, finally challenges and future of tissue engineering in dentistry. Only those articles that dealt with the tissue engineering in dentistry were selected. There have been a recent surge in guided tissue engineering methods to manage periodontal diseases beyond the traditional approaches. However, the predictable reconstruction of the innate organisation and function of whole teeth as well as their periodontal structures remains challenging. Despite some limited progress and minor successes, there remain distinct and important challenges in the development of reproducible and clinically safe approaches for oral tissue repair and regeneration. Clearly, there is a convincing body of evidence which confirms the need for this type of treatment, and public health data worldwide indicates a more than adequate patient resource. The future of these therapies involving more biological approaches and the use of dental tissue stem cells is promising and advancing. Also there may be a significant interest of their application and wider potential to treat disorders beyond the craniofacial region. Considering the

The abrasive effect of commercial whitening toothpastes on eroded enamel.

PubMed

Mosquim, Victor; Martines Souza, Beatriz; Foratori Junior, Gerson Aparecido; Wang, Linda; Magalhães, Ana Carolina

2017-06-01

To evaluate the in vitro abrasive effect of commercial whitening toothpastes on eroded bovine enamel samples in respect to erosive tooth wear. 72 bovine crowns were embedded, polished and subjected to the baseline profile analysis. The samples were then protected in 2/3 of the enamel surface and were randomly assigned to six groups (n= 12/group): G1: Oral-B 3D White, G2: Close-up Diamond Attraction Power White, G3: Sorriso Xtreme White 4D, G4: Colgate Luminous White, G5: Crest (conventional toothpaste), G6:erosion only (control). All samples were submitted to an erosive pH cycling (4 x 90 seconds in 0.1% citric acid, pH 2.5, per day) and abrasive challenges (2 x 15 seconds, per day) for 7 days. After the first and the last daily cycles, the samples were subjected to abrasive challenges, using a toothbrushing machine, soft toothbrushes and slurry of the tested toothpastes (1.5 N). Between the challenges, the samples were immersed in artificial saliva. The final profile was obtained and overlaid to the baseline profile for the calculation of the erosive tooth wear (μm). The data were subjected to Kruskal-Wallis/Dunn tests (P< 0.05). G1 promoted the highest enamel wear (3.68±1.06 μm), similarly to G3 (3.17± 0.80 μm) and G4 (3.44± 1.29 μm). G3 and G4 performed similarly between them and compared with G5 (2.35± 1.44 μm). G2 (1.51± 0.95 μm) and G6 (0.85± 0.36 μm) showed the lowest enamel wear, which did not differ between them and from G5. Oral-B 3D White showed the highest abrasive potential while Close-up Diamond Attraction Power White showed the lowest abrasive potential on eroded enamel in vitro. This study showed that some commercial whitening toothpastes, especially those containing pyrophosphate associated with hydrated silica, enhanced enamel erosive wear.

Self inflicted corneal abrasions due to delusional parasitosis

PubMed Central

Meraj, Adeel; Din, Amad U; Larsen, Lynn; Liskow, Barry I

2011-01-01

The authors report a case of self inflicted bilateral corneal abrasions and skin damage due to ophthalmic and cutaneous delusional parasitosis. A male in his 50s presented with a 10 year history of believing that parasites were colonizing his skin and biting into his skin and eyes. The patient had received extensive medical evaluations that found no evidence that symptoms were due to a medical cause. He was persistent in his belief and had induced bilateral corneal abrasions and skin damage by using heat lamps and hair dryers in an attempt to disinfect his body. The patient was treated with olanzapine along with treatment for his skin and eyes. His delusional belief system persisted but no further damage to his eyes and skin was noted on initial follow-up. PMID:22689836

Computational Fluid Dynamics Analysis of Nozzle in Abrasive Water Jet Machining

NASA Astrophysics Data System (ADS)

Venugopal, S.; Chandresekaran, M.; Muthuraman, V.; Sathish, S.

2017-03-01

Abrasive water jet cutting is one of the most recently developed non-traditional manufacturing technologies. The general nature of flow through the machining, results in rapid wear of the nozzle which decrease the cutting performance. It is well known that the inlet pressure of the abrasive water suspension has main effect on the erosion characteristics of the inner surface of the nozzle. The objective of the project is to analyze the effect of inlet pressure on wall shear and exit kinetic energy. The analysis would be carried out by varying the inlet pressure of the nozzle, so as to obtain optimized process parameters for minimum nozzle wear. The two phase flow analysis would be carried by using computational fluid dynamics tool CFX. The availability of minimized process parameters such as of abrasive water jet machining (AWJM) is limited to water and experimental test can be cost prohibitive.

Aeolian Rat Tails (ARTs): A New Morphological Indicator of Abrasion Direction

NASA Astrophysics Data System (ADS)

Favaro, E. A.; Hugenholtz, C.; Barchyn, T.

2016-12-01

Aeolian rat tails (ARTs) are a previously undocumented aeolian abrasion feature observed on ignimbrite surfaces in the Puna Plateau of Northwest Argentina and bare morphological similarity to small-scale features on Mars. We describe the terrestrial features and present an evolutionary sequence from inception to demise. ARTs are regionally-ubiquitous and characterized by a windward abrasion-resistant lithic clast and a downwind-tapering tail. The size of ARTs is controlled by the diameter of the windward lithic clast, observed on the sub-decimeter to meter scale. Their distribution throughout the Campo de Piedra Pómez, and adjacent regions is determined by the ignimbrite clast content. ARTs develop under a uni-modal abrasion direction when lithic clasts are eroded out of the ignimbrite matrix, protrude from the surface, and shelter material directly behind the clast. As the surrounding material is eroded away, a downwind-tapered tail develops. Continued erosion of the adjacent surface leads to the undercutting of clasts, liberating them from the feature where, if small enough, the clasts can be transported downwind, leading to the destruction of the tail and ultimately the feature. This evolutionary sequence accounts not only for the morphology of the feature, but also the presence of loose clasts on the ignimbrite surface, which plays a role in the development of other enigmatic landforms in the area, such as periodic bedrock ridges, yardangs, and megaripples. The significance of the identification of ARTs is due to the necessity of uni-modal abrasion direction for their development, thereby making their orientation a diagnostic indicator of long-term aeolian abrasion direction. ARTs are likely analogs of features identified by MSL Curiosity Rover on Mars, possibly providing information on past and present wind regimes.

A Study on Postmortem Wound Dating by Gross and Histopathological Examination of Abrasions

PubMed Central

Vinay, Javaregowda; Harish, Sathyanarayana; Mangala, Gouri S.R.; Hugar, Basappa S.

2017-01-01

Introduction Abrasions are the most common blunt force injuries. The precise dating of injury is extremely important in forensic medicine practice. As we know, the wound healing occurs in well-orchestrated sequence, consisting of inflammation, proliferation, and maturation. A study of occurrence of such phases will help in understanding the sequence of events in wound healing. In this context, this study of wound dating from gross and microscopic level was taken. Materials and Methods Postmortem study of wound dating by gross and histopathological examination of abrasions was carried out in the Department of Forensic Medicine, in M.S. Ramaiah Medical College. A total of 101 abrasions were correlated to time frame the occurrence of different gross changes and microscopic changes that follow the blunt trauma. Abrasions ranging from 0 hour to a maximum of 45 days were studied. Results The gross changes of abrasions were in correlation with the microscopic changes; however, the role of the comorbid conditions is significant because the results showed variations with respect to healing process. Conclusions This study signifies that, if naked eye examination is studied along with histopathological examination, the reliability and accuracy of dating of wound increase. Whenever accurate determination of age is required, the autopsy surgeon can subject the samples for histopathological examination and correlate before opining the age of injury. PMID:28418938

Aviation dentistry: current concepts and practice.

PubMed

Zadik, Y

2009-01-10

With the growing number of air passengers, flight attendants, leisure pilots as well as military and airline pilots, dentists may increasingly encounter flight-related oral conditions requiring treatment. Moreover, dentists should prevent the creation of in-flight hazards when treating aircrew members. The aim of this article is to introduce the concepts of aviation (aerospace) medicine and dentistry. Data were gathered to cover the following issues: head and facial barotraumas (barotrauma-related headache, external otitic barotrauma, barosinusitis and barotitis-media), dental barotrauma (barometric pressure-related tooth injury), barodontalgia (barometric pressure-related oro-dental pain), and dental care for aircrews. Special considerations have to be made when planning restorative, endodontic, prosthodontic and surgical treatment to an aircrew patient. This article supplies the dental practitioner with some diagnostic tools as well as treatment guidelines. Principles of prevention, periodic examination, dental-related flight restriction (grounding) and dental documentation (for forensic purposes) are described as well.

[Resin-modified glass-ionomers in dentistry].

PubMed

Gladys, S; Van Meerbeek, B; Braem, M; Lambrechts, P; Vanherle, G

1996-11-01

The resin-modified glass-ionomers contain the essential components of both a conventional glass-ionomer and a visible light-cured resin. They have several advantages like longer working time, shorter setting time, bonding to tooth structure, fluoride-release, better aesthetics than conventional glass-ionomers and ease in use. As disadvantages can be mentioned the polymerisation shrinkage, trapping of air-bubbles, difficulties in colour choice and contouring. A physical and mechanical characterisation was necessary to define the possibilities and limits of these materials. It can be stated that the strength and aesthetic appearance of resin-modified glass-ionomers are less than that of composites, but better than that of conventional glass-ionomers. Clinically, this is expressed in a rough and dull surface compared to a composite restoration. They are not indicated in stress bearing areas. Consequently, they are mainly indicated in cervical class V-restorations in the postcanine region, and probably restorations in pedodontics, geriatric dentistry and for patients with a high caries activity.

Demand in pediatric dentistry for sedation and general anesthesia by dentist anesthesiologists: a survey of directors of dentist anesthesiologist and pediatric dentistry residencies.

PubMed

Hicks, C Gray; Jones, James E; Saxen, Mark A; Maupome, Gerardo; Sanders, Brian J; Walker, Laquia A; Weddell, James A; Tomlin, Angela

2012-01-01

This study describes what training programs in pediatric dentistry and dental anesthesiology are doing to meet future needs for deep sedation/general anesthesia services required for pediatric dentistry. Residency directors from 10 dental anesthesiology training programs in North America and 79 directors from pediatric dentistry training programs in North America were asked to answer an 18-item and 22-item online survey, respectively, through an online survey tool. The response rate for the 10 anesthesiology training program directors was 9 of 10 or 90%. The response rate for the 79 pediatric dentistry training program directors was 46 of 79 or 58%. Thirty-seven percent of pediatric dentistry programs use clinic-based deep sedation/general anesthesia for dental treatment in addition to hospital-based deep sedation/general anesthesia. Eighty-eight percent of those programs use dentist anesthesiologists for administration of deep sedation/general anesthesia in a clinic-based setting. Pediatric dentistry residency directors perceive a future change in the need for deep sedation/general anesthesia services provided by dentist anesthesiologists to pediatric dentists: 64% anticipate an increase in need for dentist anesthesiologist services, while 36% anticipate no change. Dental anesthesiology directors compared to 2, 5, and 10 years ago have seen an increase in the requests for dentist anesthesiologist services by pediatric dentists reported by 56% of respondents (past 2 years), 63% of respondents (past 5 years), and 88% of respondents (past 10 years), respectively. Predicting the future need of dentist anesthesiologists is an uncertain task, but these results show pediatric dentistry directors and dental anesthesiology directors are considering the need, and they recognize a trend of increased need for dentist anesthesiologist services over the past decade.

Information regarding restorative dentistry for new graduates.

PubMed

Kalsi, A S; Lewis, N J; Hemmings, K W

2016-10-07

A recent national survey has shown the need for clarification regarding the various disciplines encompassed by restorative dentistry and their respective training pathways. This document aims to address this by outlining the remit of restorative dentistry, in addition to the various job roles involved. This information is being disseminated by the British Society for Restorative Dentistry, and given the relevance to referrers and those looking for insight into the speciality, it has been reproduced here. Roles within the speciality range from dentists with special interests to specialists and consultants, whether primarily academic or clinical. The choice that a new graduate may make to choose a specific route will likely depend on a number of factors, often specific to each individual. Guidance on ways to gain experience and sources of further information are also provided.

Interprofessional Collaborative Practice: How Could Dentistry Participate?

PubMed

Cole, James R; Dodge, William W; Findley, John S; Horn, Bruce D; Kalkwarf, Kenneth L; Martin, Max M; Valachovic, Richard W; Winder, Ronald L; Young, Stephen K

2018-05-01

There is a remarkable phenomenon occurring among health professionals: the development of ongoing, routine collaboration, both in educating the next generation of providers and in delivering care. These new approaches, commonly referred to as interprofessional education and interprofessional collaborative practice, have been introduced into academic health settings and delivery systems throughout the U.S. and the rest of the world; however, the full integration of dentistry in health care teams remains unrealized. In academic settings, dentistry has found ways to collaborate with the other health professions, but most practicing dentists still find themselves on the margins of new models of care delivery. This article provides a perspective on the history and context of the evolution of collaborative approaches to health care and proposes ways in which dentistry can participate more fully in the future.

Recent advances in imaging technologies in dentistry.

PubMed

Shah, Naseem; Bansal, Nikhil; Logani, Ajay

2014-10-28

Dentistry has witnessed tremendous advances in all its branches over the past three decades. With these advances, the need for more precise diagnostic tools, specially imaging methods, have become mandatory. From the simple intra-oral periapical X-rays, advanced imaging techniques like computed tomography, cone beam computed tomography, magnetic resonance imaging and ultrasound have also found place in modern dentistry. Changing from analogue to digital radiography has not only made the process simpler and faster but also made image storage, manipulation (brightness/contrast, image cropping, etc.) and retrieval easier. The three-dimensional imaging has made the complex cranio-facial structures more accessible for examination and early and accurate diagnosis of deep seated lesions. This paper is to review current advances in imaging technology and their uses in different disciplines of dentistry.

Recent advances in imaging technologies in dentistry

PubMed Central

Shah, Naseem; Bansal, Nikhil; Logani, Ajay

2014-01-01

Dentistry has witnessed tremendous advances in all its branches over the past three decades. With these advances, the need for more precise diagnostic tools, specially imaging methods, have become mandatory. From the simple intra-oral periapical X-rays, advanced imaging techniques like computed tomography, cone beam computed tomography, magnetic resonance imaging and ultrasound have also found place in modern dentistry. Changing from analogue to digital radiography has not only made the process simpler and faster but also made image storage, manipulation (brightness/contrast, image cropping, etc.) and retrieval easier. The three-dimensional imaging has made the complex cranio-facial structures more accessible for examination and early and accurate diagnosis of deep seated lesions. This paper is to review current advances in imaging technology and their uses in different disciplines of dentistry. PMID:25349663

Current applications of nanotechnology in dentistry: a review.

PubMed

Bhavikatti, Shaeesta Khaleelahmed; Bhardwaj, Smiti; Prabhuji, M L V

2014-01-01

With the increasing demand for advances in diagnosis and treatment modalities, nanotechnology is being considered as a groundbreaking and viable research subject. This technology, which deals with matter in nanodimensions, has widened our views of poorly understood health issues and provided novel means of diagnosis and treatment. Researchers in the field of dentistry have explored the potential of nanoparticles in existing therapeutic modalities with moderate success. The key implementations in the field of dentistry include local drug delivery agents, restorative materials, bone graft materials, and implant surface modifications. This review provides detailed insights about current developments in the field of dentistry, and discusses potential future uses of nanotechnology.

Experimental Evidence that Abrasion of Carbonate Sand is a Significant Source of Carbonate Mud

NASA Astrophysics Data System (ADS)

Trower, L.; Kivrak, L.; Lamb, M. P.; Fischer, W. W.

2017-12-01

Carbonate mud is a major sedimentary component of modern and ancient tropical carbonate environments, yet its enigmatic origin remains debated. Early views on the origin of carbonate mud considered the abrasion of carbonate sand during sediment transport as a possible mechanism. In recent decades, however, prevailing thought has generally settled on a binary explanation: 1) precipitation of aragonite needles within the water column, and 2) post-mortem dispersal of biological aragonite, in particular from algae, and perhaps aided by fish. To test these different hypotheses, we designed a model and a set of laboratory experiments to quantify the rates of mud production associated with sediment transport. We adapted a recent model of ooid abrasion rate to predict the rate of mud production by abrasion of carbonate sand as a function of grain size and sediment transport mode. This model predicts large mud production rates, ranging from 103 to 104 g CaCO3/m2/yr for typical grain sizes and transport conditions. These rate estimates are at least one order of magnitude more rapid than the 102 g CaCO3/m2/yr estimates for other mechanisms like algal biomineralization, indicating that abrasion could produce much larger mud fluxes per area as other mechanisms. We tested these estimates using wet abrasion mill experiments; these experiments generated mud through mechanical abrasion of both ooid and skeletal carbonate sand for grain sizes ranging from 250 µm to >1000 µm over a range of sediment transport modes. Experiments were run in artificial seawater, including a series of controls demonstrating that no mud was produced via homogenous nucleation and precipitation in the absence of sand. Our experimental rates match the model predictions well, although we observed small systematic differences in rates between abrasion ooid sand and skeletal carbonate sand that likely stems from innate differences in grain angularity. Electron microscopy of the experimental products revealed

Use of antidepressants in dentistry: A systematic review.

PubMed

Lino, P A; Martins, C C; Miranda, Gfpc; de Souza E Silva, M E; de Abreu, Mhng

2017-08-24

Previous research has suggested that antidepressants can be used in oral health care. The aim of this systematic review was to search for scientific evidence of the efficacy of the use of antidepressants in dentistry. The clinical question was as follows (PICO question): dentistry patients (Patients); antidepressants (Intervention); no use or placebo or other drug (Comparison); and efficacy in oral health problems (Outcome). An electronic search was conducted in seven databases, as well as a manual search without restriction regarding language and date of publication. Two independent reviewers selected studies based on eligibility criteria, extracted data and assessed methodological quality based on the PEDro scale. The PROSPERO record is number CRD42016037442. A total of 15 randomized controlled trials were associated with the use of antidepressants to control chronic or acute pain in dentistry, among other conditions such as bruxism and burning mouth syndrome. The most commonly used drug in clinical trials was amitriptyline (more than 50% of studies). Antidepressants may be effective in dentistry for acute and chronic pain, but there is a large amount of methodological heterogeneity among the evaluated studies. In summary, there is rationality for the indication of this class of medicine in dentistry in specific clinical situations. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd. All rights reserved.

Micro-abrasion-corrosion behaviour of a biomedical Ti-25Nb-3Mo-3Zr-2Sn alloy in simulated physiological fluid.

PubMed

Wang, Zhenguo; Li, Yan; Huang, Weijiu; Chen, Xiaoli; He, Haoran

2016-10-01

The micro-abrasion-corrosion behaviour of the biomedical Ti-25Nb-3Mo-3Zr-2Sn alloy in Hank׳s solution with protein has been investigated using electrochemical measurements, tribological tests and scanning electron microscope (SEM) observations. The potentiodynamic polarization tests showed that the corrosion potential (Ecorr) exhibits the maximum value at the abrasive concentration of 0.05gcm(-3) despite of the load level. The tribological results indicated that the total material loss of the Ti-25Nb-3Mo-3Zr-2Sn alloy during micro-abrasion increased with the increasing abrasive concentration at a certain applied load. When the abrasive concentration is no more than 0.15gcm(-3), the total material loss increases with increasing load, while the total material loss exhibits the maximum value at a moderate load in case of higher abrasive concentration levels. This was ascribed to the three-body or two-body micro-abrasion-corrosion at different abrasive concentration levels. The wastage map, abrasion mode map and synergy map associated with the applied load and the abrasive concentration were constructed to evaluate the micro-abrasion-corrosion behaviour of the Ti-25Nb-3Mo-3Zr-2Sn alloy in potential biomedical applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Adhesive and abrasive wear mechanisms in ion implanted metals

NASA Astrophysics Data System (ADS)

Dearnaley, G.

1985-03-01

The distinction between adhesive and abrasive wear processes was introduced originally by Burwell during the nineteen-fifties, though some authors prefer to classify wear according to whether it is mild or severe. It is argued here that, on the basis of the performance of a variety of ion implanted metal surfaces, exposed to different modes of wear, the Burwell distinction is a valid one which, moreover, enables us to predict under which circumstances a given treatment will perform well. It is shown that, because wear rates under abrasive conditions are very sensitive to the ratio of the hardness of the surface to that of the abrasive particles, large increases in working life are attainable as a result of ion implantation. Under adhesive wear conditions, the wear rate appears to fall inversely as the hardness increases, and it is advantageous to implant species which will create and retain a hard surface oxide or other continuous film in order to reduce metal-metal contact. By the appropriate combination of physico-chemical changes in an implanted layer it has been possible to reduce wear rates by up to three orders of magnitude. Such rates compensate for the shallow depths achievable by ion implantation.

SCDA task force on a special care dentistry residency.

PubMed

Hicks, Jeffery; Vishwanat, Lakshmi; Perry, Maureen; Messura, Judith; Dee, Kristin

2016-07-01

The Special Care Dentistry Association (SCDA) has acted on a proposal regarding the status of training in the care of patients with special needs. Two phases of action were undertaken. Phase 1: (a) examination of the literature on existing training and curricula in the care of patients with special needs and (b) a survey of existing postdoctoral programs in special needs. Phase 2: establish a group of experts who: (a) submitted to the Commission on Dental Accreditation a request to approve a postdoctoral general dentistry residency program in Special Care Dentistry and (b) created suggested accreditation standards for such postdoctoral programs. This article describes efforts by the SCDA to evaluate: The status of existing training of dental students in the care of patients with special needs. The number and characteristics of postdoctoral general dentistry programs offering formal training in the care of patients with special needs. Whether additional training in the care of patients with special needs is needed for dental students and -dentists. Possible actions by SCDA to impact the numbers of dentists trained each year in the care of patients with -special needs. © 2016 Special Care Dentistry Association and Wiley Periodicals, Inc.

Pre-polishing on a CNC platform with bound abrasive contour tools

NASA Astrophysics Data System (ADS)

Schoeffer, Adrienne E.

2003-05-01

Deterministic micorgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-51.tm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an OptiproTM CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Abrasive Wear of Four Direct Restorative Materials by Standard and Whitening Dentifrices

DTIC Science & Technology

2013-06-01

after an acidic challenge . Enamel loss was significantly greater when erosive and abrasive effects were combined. They concluded that acid-softened...surrounding soft tissues. Another benefit of restoration is the elimination of a challenging area for the patient and hygienist to clean. These areas...abrasion challenge ; the resin cement with the smallest sized filler particles had the smallest weight loss and maintained the smoothest surface of all the

Comparative evaluation of enamel abrasivity by toothbrush and velcro: An in vitro scanning electron microscope study

PubMed Central

Ojha, Saroj Kumar; Javdekar, Sadashiv Bhaskar; Dhir, Sangeeta

2015-01-01

Context: Plaque control has been shown to be pivotal in maintaining the optimal periodontal health. Mechanical plaque control is the most popular option for establishing the optimal oral health. Toothbrushes have been the novel tool for mechanical cleansing. However, the abrasive potential of the toothbrushes on the enamel surface is an area in gray. Aims: The aim of this in vitro study is to evaluate the abrasivity of the toothbrush versus the velcro fasteners. Materials and Methods: The mounted teeth of both the groups were subjected to abrasion test, and the tooth surfaces were observed for the possible abrasions from the oscillating strokes (toothbrush) and frictional contacts (hook and loop velcro) and examined under the scanning electron microscope. Results: Comparative assessment of both velcro (hook and loop) and toothbrush bristles did not reveal any evidence of abrasion on the tooth specimens. Conclusions: Veclro fasteners are safe and qualitatively at par to the manual toothbrush for their efficacy and efficiency in teeth cleansing PMID:26229264

Design of a new abrasive slurry jet generator

NASA Astrophysics Data System (ADS)

Wang, F. C.; Shi, L. L.; Guo, C. W.

2017-12-01

With the advantages of a low system working pressure, good jet convergence and high cutting quality, abrasive slurry jet (ASJ) has broad application prospects in material cutting and equipment cleaning. Considering that the generator plays a crucial role in ASJ system, the paper designed a new type ASJ generator using an electric oil pump, a separate plunger cylinder, and a spring energized seal. According to the determining of structure shape, size and seal type, a new ASJ generator has been manufactured out and tested by a series of experiments. The new generator separates the abrasive slurry from the dynamic hydraulic oil, which can improve the service life of the ASJ system. And the new ASJ system can reach 40 MPa and has good performance in jet convergence, which deserves to popularization and application in materials machining.

Top-Cited Articles in Implant Dentistry.

PubMed

Fardi, Anastasia; Kodonas, Konstantinos; Lillis, Theodoros; Veis, Alexander

Citation analysis is the field of bibliometrics that uses citation data to evaluate the scientific recognition and the influential performance of a research article in the scientific community. The aim of this study was to conduct a bibliometric analysis of the top-cited articles pertaining to implant dentistry, to analyze the main characteristics, and to display the most interesting topics and evolutionary trends. The 100 top-cited articles published in "Dentistry, Oral Surgery, and Medicine" journals were identified using the Science Citation Index Database. The articles were further reviewed, and basic information was collected, including the number of citations, journals, authors, publication year, study design, level of evidence, and field of study. The highly cited articles in implant dentistry were cited between 199 and 2,229 times. The majority of them were published in four major journals: Clinical Oral Implants Research, International Journal of Oral & Maxillofacial Implants, Journal of Clinical Periodontology, and Journal of Periodontology. The publication year ranged from 1981 to 2009, with 45% published in a nine-year period (2001 to 2009). Publications from the United States (29%) were the most heavily cited, followed by those from Sweden (23%) and Switzerland (17%). The University of Göteborg from Sweden produced the highest number of publications (n = 19), followed by the University of Bern in Switzerland (n = 13). There was a predominance of clinical papers (n = 42), followed by reviews (n = 25), basic science research (n = 21), and proceedings papers (n = 12). Peri-implant tissue healing and health (24%), implant success/failures (19.2%), and biomechanical topics (16.8%) were the most common fields of study. Citation analysis in the field of implant dentistry reveals interesting information about the topics and trends negotiated by researchers and elucidates which characteristics are required for a paper to attain a "classic" status. Clinical

Lower back and neck pain among dentistry students: a cross-sectional study in dentistry students in Northern Greece.

PubMed

Samoladas, Efthimios; Barmpagianni, Christina; Papadopoulos, Dimitrios V; Gelalis, Ioannis D

2018-03-28

Dentistry students and dentists comprise a unique group of professionals, whose everyday professional activity requires long hours of standing and working in a position considered unhealthy for the lower back and neck. Our aim was to explore the factors involved in the appearance of low back and neck pain in dentistry students as well as the impact of the pain on the students' professional and everyday activities. A questionnaire was given to all dentistry students of the 4th and 5th year of our university. The questionnaire included 43 questions regarding demographic data, history (spinal injury, other comorbidities), daily activities (exercise, smoking, alcohol and caffeine consumption, use of cell phone), professional activities (length and type of dental work), pattern and intensity of pain, and personal pain evaluation. A statistical analysis of the gathered data was performed. All students having suffered a spinal trauma or indicating any other comorbidity that could cause severe pain of the spine were excluded from the study. Fifty-five students (21 male, 34 female) were included. Our data showed that increased alcohol consumption and prolonged use of cell phone were connected to increased levels of pain. The students reported that the most frequent onset of pain was 1 h after starting to work in a standing position, while the majority believed that their working habits were involved in the appearance and the intensity of neck and low-back pain. Our findings indicate that among dentistry students appears to be a causative relationship between their professional activities and the experienced spinal pain. These findings may be useful in a possible future restructuring of the educational program in dental schools, as well as in improving the ergonomics of dentistry working units.

Demand in Pediatric Dentistry for Sedation and General Anesthesia by Dentist Anesthesiologists: A Survey of Directors of Dentist Anesthesiologist and Pediatric Dentistry Residencies

PubMed Central

Hicks, C. Gray; Jones, James E.; Saxen, Mark A.; Maupome, Gerardo; Sanders, Brian J.; Walker, LaQuia A.; Weddell, James A.; Tomlin, Angela

2012-01-01

This study describes what training programs in pediatric dentistry and dental anesthesiology are doing to meet future needs for deep sedation/general anesthesia services required for pediatric dentistry. Residency directors from 10 dental anesthesiology training programs in North America and 79 directors from pediatric dentistry training programs in North America were asked to answer an 18-item and 22-item online survey, respectively, through an online survey tool. The response rate for the 10 anesthesiology training program directors was 9 of 10 or 90%. The response rate for the 79 pediatric dentistry training program directors was 46 of 79 or 58%. Thirty-seven percent of pediatric dentistry programs use clinic-based deep sedation/general anesthesia for dental treatment in addition to hospital-based deep sedation/general anesthesia. Eighty-eight percent of those programs use dentist anesthesiologists for administration of deep sedation/general anesthesia in a clinic-based setting. Pediatric dentistry residency directors perceive a future change in the need for deep sedation/general anesthesia services provided by dentist anesthesiologists to pediatric dentists: 64% anticipate an increase in need for dentist anesthesiologist services, while 36% anticipate no change. Dental anesthesiology directors compared to 2, 5, and 10 years ago have seen an increase in the requests for dentist anesthesiologist services by pediatric dentists reported by 56% of respondents (past 2 years), 63% of respondents (past 5 years), and 88% of respondents (past 10 years), respectively. Predicting the future need of dentist anesthesiologists is an uncertain task, but these results show pediatric dentistry directors and dental anesthesiology directors are considering the need, and they recognize a trend of increased need for dentist anesthesiologist services over the past decade. PMID:22428968

Evidence-based dentistry: fundamentals for the dentist.

PubMed

Bauer, Janet; Chiappelli, Francesco; Spackman, Sue; Prolo, Paolo; Stevenson, Richard

2006-06-01

This article explains the fundamentals of evidence-based dentistry for the dentist. Evidence-based dentistry is a discipline whose primary participant is the translational researcher. Recent developments have emphasized the importance of this discipline (clinical and translational research) for improving health care. The process of evidence-based dentistry is the reciprocation of new and existing evidence between dentists and quantitative and qualitative researchers, facilitated by the translational researcher. The product of this reciprocation is the clinical practice guideline, or best evidence, that provides the patient options in choosing treatments or services. These options are quantified and qualified by decision, utility, and cost data. Using shared decision-making, the dentist and patient arrive at a mutual understanding of which option best meets an acceptable and preferred treatment course that is cost effective. This option becomes the clinical decision.

Gingival abrasion and recession in manual and oscillating–rotating power brush users

PubMed Central

Rosema, NAM; Adam, R; Grender, JM; Van der Sluijs, E; Supranoto, SC; Van der Weijden, GA

2014-01-01

Objective To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). Methods This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young adult participants: 90 manual brush users and 91 oscillating–rotating power brush users. Participants were assessed for GR and GA as primary response variables. Secondary response variables were the level of gingival inflammation, plaque score reduction and brushing duration. Pearson correlation was used to describe the relationship between number of recession sites and number of abrasions. Prebrushing (baseline) and post-brushing GA and plaque scores were assessed and differences analysed using paired tests. Two-sample t-test was used to analyse group differences; ancova was used for analyses of post-brushing changes with baseline as covariate. Results Overall, 97.8% of the study population had at least one site of ≥1 mm of gingival recession. For the manual group, this percentage was 98.9%, and for the power group, this percentage was 96.7% (P = 0.621). Post-brushing, the power group showed a significantly smaller GA increase than the manual group (P = 0.004); however, there was no significant correlation between number of recession sites and number of abrasions for either group (P ≥ 0.327). Conclusions Little gingival recession was observed in either toothbrush user group; the observed GR levels were comparable. Lower post-brushing gingival abrasion levels were seen in the power group. There was no correlation between gingival abrasion as a result of brushing and the observed gingival recession following use of either toothbrush. PMID:24871587

Assessment of thermal spray coatings for wear and abrasion resistance applications

NASA Astrophysics Data System (ADS)

Karode, Ishaan Nitin

Thermal spray cermet and metallic coatings are extensively used for wear, abrasion and corrosion control in a variety of industries. The first part of the thesis focuses mainly on testing of sand erosion resistance of thermal spray coatings on carbon composites used in the manufacture of helicopter rotor blades. The test set-up employed is a sand blasting machine and is an effort to duplicate the in-flight conditions especially those encountered in hot arid conditions. The technique adopted follows the Department of Defence test method standard. Carbon Composites have excellent stiffness, strength and low weight/density. The strength to weight ratio is high. Hence, these are used in aerospace applications to a large extent. However, the biggest problem encountered with carbon composites is its low abrasion resistance as its surface is very weak. Hence, thermal spray coatings are used to improve the surface properties of CFRP. Zinc bond coats and WC-Co coatings were tested. However, high amount of thermal stresses were developed between the substrate and the coating due to large differences in the CTE's of the both, leading to high mass losses within two minutes and just 130 grams of sand sprayed on to the coatings with the sand blasting machine built; and hence the coatings with CC as a substrate could not qualify for the application. The second part of the thesis focuses on the assessment of different thermal spray coatings used for manufacture of mechanical seals in pumps and analyze the best coating material for the wear resistance application through detail quantification of material loss by block-on-ring test set-up. A machine based on Block-on-ring test set-up following ASTM G77 (Measurement of Adhesive wear resistance of thermal spray coatings) standards was built to duplicate the pump conditions. Thermally sprayed coated materials were tested in different conditions (Load, time, abrasive). WC-Co had the highest wear resistance (lower volume losses) and

Effects of Load and Speed on Wear Rate of Abrasive Wear for 2014 Al Alloy

NASA Astrophysics Data System (ADS)

Odabas, D.

2018-01-01

In this paper, the effects of the normal load and sliding speed on wear rate of two-body abrasive wear for 2014 Al Alloy were investigated in detail. In order to understand the variation in wear behaviour with load and speed, wear tests were carried out at a sliding distance of 11 m, a speed of 0.36 m/s, a duration of 30 s and loads in the range 3-11 N using 220 grit abrasive paper, and at a speed range 0.09-0.90 m/s, a load of 5 N and an average sliding distance of 11 m using abrasive papers of 150 grit size under dry friction conditions. Before the wear tests, solution treatment of the 2014 Al alloy was carried out at temperatures of 505 and 520 °C for 1 h in a muffle furnace and then quenched in cold water at 15 °C. Later, the ageing treatment was carried out at 185 °C for 8 h in the furnace. Generally, wear rate due to time increased linearly and linear wear resistance decreased with increasing loads. However, the wear rate was directly proportional to the load up to a critical load of 7 N. After this load, the slope of the curves decreased because the excessive deformation of the worn surface and the instability of the abrasive grains began to increase. When the load on an abrasive grain reaches a critical value, the groove width is about 0.17 of the abrasive grain diameter, and the abrasive grains begin to fail. The wear rate due to time increased slightly as the sliding speed increased in the range 0.09-0.90 m/s. The reason for this is that changes arising from strain rate and friction heating are expected with increasing sliding speeds.

The worn dentition--pathognomonic patterns of abrasion and erosion.

PubMed

Abrahamsen, Thomas C

2005-01-01

Historically, the dental literature has revealed various causes of tooth wear, yet it has failed to provide a conclusive method of differentiation and diagnosis of the condition. The categories of tooth wear encountered most commonly in dental practice are abrasion and erosion. The major causes of wear from abrasion are bruxism and toothpaste abuse, and the major causes of wear from erosion are regurgitation, coke-swishing and fruit-mulling. Through in-depth clinical study of these causes, this paper provides a diagnostic system that will enable dental professionals to determine and differentiate the exact aetiology of the worn dentition simply by the recognition of the pathognomonic wear patterns on diagnostic casts, which are based upon the position and quantity of the non-carious loss of tooth structure.

Controls on wind abrasion patterns through a fractured bedrock landscape

NASA Astrophysics Data System (ADS)

Perkins, J. P.; Finnegan, N. J.

2017-12-01

Wind abrasion is an important geomorphic process for understanding arid landscape evolution on Earth and interpreting the post-fluvial history of Mars. Both the presence and orientation of wind-abraded landforms provide potentially important constraints on paleo-climatic conditions; however, such interpretations can be complicated by lithologic and structural heterogeneity. To explore the influence of pre-existing structure on wind abrasion, we exploit a natural experiment along the 10.2 Ma Lower Rio San Pedro ignimbrite in northern Chile. Here, a 3.2 Ma andesite flow erupted from Cerro de las Cuevas and deposited atop the ignimbrite, supplying wind-transportable sediment and initiating a phase of downwind abrasion. Additionally, the lava flow provides a continually varying degree of upwind topographic shielding along the ignimbrite that is reflected in a range of surface morphologies. Where fully shielded the ignimbrite surface is partially blanketed by sediment. However, as relief decreases the surface morphology shifts from large polygonal structures that emerge due to the concentration of wind abrasion along pre-existing fracture sets, to polygons that are bisected by wind-parallel grooves that cross-cut fracture sets, to linear sets of yardangs. We reconstruct the ignimbrite surface using a high-resolution digital elevation model, and calculate erosion rates ranging from 0.002 to 0.45 mm/kyr that vary strongly with degree of topographic shielding (R2 = 0.97). We use measured abrasion rates together with nearby weather station data to estimate the nondimensional Rouse number and Inertial Parameter for a range of particle sizes. From these calculations, we hypothesize that the change from fracture-controlled to flow-controlled morphology reflects increases in the grain size and inertia of particles in the suspension cloud. Where the ignimbrite experiences persistent high winds, large particles may travel in suspension and are largely insensitive to topographic

Martian and Terrestrial Rock Abrasion from Wind Tunnel and Field Studies

NASA Technical Reports Server (NTRS)

Bridges, N. T.; Greeley, R.; Eddlemon, E.; Laity, J. E.; Meyer, C.; Phoreman, J.; White, B. R.

2003-01-01

Earth and Mars exhibit ventifacts, rocks that have been abraded by saltating sand. Previous theoretical and laboratory studies have determined abrasion susceptibilities of rocks as a function of sand type and impact angle and rock material strengths. For the last two years we have been engaged in wind tunnel and field studies to better understand the fundamental factors which control and influence rock abrasion and ventifact formation on Earth and Mars. In particular, we are examining: 1) What types of rocks (composition, texture, and shape) preferentially erode and what are the relative rates of one type vs. another? 2) What are the controlling factors of the aeolian sand cloud (flux, particle speed, surface roughness, etc) which favor rock abrasion?, 3) How do specific ventifact characteristics tie into their mode of formation and rock properties? We find several important factors: 1) Initial rock shape controls the rate of abrasion, with steeper faces abrading faster than shallower ones. The relationship is partly dependent on angle-dependent flux (proportional to sin[theta]) but exhibits additional non-linear effects from momentum transfer efficiency and rebound effects that vary with incidence angle. 2) Irregular targets with pits or grooves abrade at greater rates than targets with smooth surfaces, with indentations generally enlarging with time. Surfaces become rougher with time. 3) Targets also abrade via slope retreat, which is roughly dependent on the slope of the front face. The formation of basal sills is common, as observed on terrestrial and Martian ventifacts.

Air bags and the skin.

PubMed

Corazza, Monica; Trincone, Silvana; Zampino, Maria Rosaria; Virgili, Annarosa

2004-01-01

Air bags, fitted in the majority of new automobiles, are safety devices activated when a sudden deceleration causes the ignition of a propellant cartridge containing sodium azide. The bag is inflated by nitrogen liberated during the combustion. Deployment releases various high-temperature gases, including nitrogen and carbon dioxide, and produces sodium hydroxide, a highly irritant alkaline substance. In about 7%-8% of cases, air bags cause dermatologic injuries such as traumatic lesions, irritant dermatitis, and chemical and thermal burns. Nondermatologic lesions, such as ocular damage (alkali keratitis, corneal abrasions), ear lesions, bone fractures, and contusive damage can also be caused by air bag deployment.

Abrasion and deformed layer formation of manganese-zinc ferrite in sliding contact with lapping tapes

NASA Technical Reports Server (NTRS)

Miyoshi, K.; Buckley, D. H.; Tanaka, K.

1986-01-01

Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and the deformed layers produced in single-crystal Mn-Zn ferrite simulated heads during contact with lapping tapes. The crystaline state of the head is changed drastically during the abrasion process. Crystalline states ranging from nearly amorphous to highly textured polycrystalline can be produced on the wear surface of a single-crystal Mn-Zn ferrite head. The total thickness of the deformed layer was approximately 0.8 microns. This thickness increased as the load and abrasive grit size increased. The anisotropic wear of the ferrite was found to be inversely proportional to the hardness of the wear surface. The wear was lower in the order 211 111 10 0110. The wear of the ferrite increased markedly with an increase in sliding velocity and abrasive grit size.

The role of erosion, abrasion and attrition in tooth wear.

PubMed

Barbour, Michele E; Rees, Gareth D

2006-01-01

There is increasing clinical awareness of erosion of enamel and dentine by dietary acids and the consequent increased susceptibility to physical wear. Enamel erosion is characterized by acid-mediated surface softening that, if unchecked, will progress to irreversible loss of surface tissue, potentially exposing the underlying dentine. In comparison, dentine erosion is less well understood as the composition and microstructure are more heterogeneous. Factors which affect the erosive potential of a solution include pH, titratable acidity, common ion concentrations, and frequency and method of exposure. Abrasion and attrition are sources of physical wear and are commonly associated with tooth brushing and tooth-to-tooth contact, respectively. A combination of erosion and abrasion or attrition exacerbates wear; however, further research is required to understand the role of fluoride in protecting mineralized tissues from such processes. Abrasive wear may be seen in a wide range of patients, whereas attritive loss is usually seen in individuals with bruxism. Wear processes are implicated in the development of dentine hypersensitivity. Saliva confers the major protective function against wear due to its role in pellicle formation, buffering, acid clearance, and hard tissue remineralization. This review focuses on the physiochemical factors impacting tooth wear.

Influence of air-particle deposition protocols on the surface topography and adhesion of resin cement to zirconia.

PubMed

Sarmento, Hugo R; Campos, Fernanda; Sousa, Rafael S; Machado, Joao P B; Souza, Rodrigo O A; Bottino, Marco A; Ozcan, Mutlu

2014-07-01

This study evaluated the influence of air-particle abrasion protocols on the surface roughness (SR) of zirconia and the shear bond strength (SBS) of dual-polymerized resin cement to this ceramic. Sintered zirconia blocks (n = 115) (Lava, 3M ESPE) were embedded in acrylic resin and polished. The specimens were divided according to the 'particle type' (Al: 110 µm Al2O3; Si: 110 µm SiO2) and 'pressure' factors (2.5 or 3.5 bar) (n = 3 per group): (a) Control (no air-abrasion); (b) Al2.5; (c) Si2.5; (d) Al3.5; (e) Si3.5. SR (Ra) was measured 3-times from each specimen after 20 s of air-abrasion (distance: 10 mm) using a digital optical profilometer. Surface topography was evaluated under SEM analyses. For the SBS test, 'particle type', 'pressure' and 'thermocycling' (TC) factors were considered (n = 10; n = 10 per group): Control (no air-abrasion); Al2.5; Si2.5; Al3.5; Si3.5; ControlTC; Al2.5TC; Si2.5TC; Al3.5TC; Si3.5TC. After silane application, resin cement (Panavia F2.0) was bonded and polymerized. Specimens were thermocycled (6.000 cycles, 5-55°C) and subjected to SBS (1 mm/min). Data were analyzed using ANOVA, Tukey's and Dunnett tests (5%). 'Particle' (p = 0.0001) and 'pressure' (p = 0.0001) factors significantly affected the SR. All protocols significantly increased the SR (Al2.5: 0.45 ± 0.02; Si2.5: 0.39 ± 0.01; Al3.5: 0.80 ± 0.01; Si3.5: 0.64 ± 0.01 µm) compared to the control group (0.16 ± 0.01 µm). For SBS, only 'particle' factor significantly affected the results (p = 0.015). The SiO2 groups presented significantly higher SBS results than Al2O3 (Al2.5: 4.78 ± 1.86; Si2.5: 7.17 ± 2.62; Al3.5: 4.97 ± 3.74; Si3.5: 9.14 ± 4.09 MPa) and the control group (3.67 ± 3.0 MPa). All TC specimens presented spontaneous debondings. SEM analysis showed that Al2O3 created damage in zirconia in the form of grooves, different from those observed with SiO2 groups. Air-abrasion with 110 µm Al2O3 resulted in higher roughness, but air-abrasion protocols with SiO2

Creating an evidence-based dentistry culture at Baylor College of Dentistry: the winds of change.

PubMed

Hinton, Robert J; Dechow, Paul C; Abdellatif, Hoda; Jones, Daniel L; McCann, Ann L; Schneiderman, Emet D; D'Souza, Rena

2011-03-01

In the early years of the new millennium, the National Institute of Dental and Craniofacial Research of the National Institutes of Health began funding Oral Health Research Education Grants using the R25 mechanism to promote the application of basic and clinical research findings to clinical training and to encourage students to pursue careers in oral health research. This report describes the impact of an R25 grant awarded to the Texas A&M Health Science Center's Baylor College of Dentistry (BCD) on its curriculum and faculty development efforts. At BCD, the R25 grant supports a multipronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all four years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent EBD culture characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty members who can model the importance of evidence-based practice is of paramount importance for the future of dentistry.

Creating an Evidence-Based Dentistry Culture at Baylor College of Dentistry: The Winds of Change

PubMed Central

Hinton, Robert J.; Dechow, Paul C.; Abdellatif, Hoda; Jones, Daniel L.; McCann, Ann L.; Schneiderman, Emet D.; D’Souza, Rena

2011-01-01

In the early years of the new millennium, the National Institute of Dental and Craniofacial Research of the National Institutes of Health began funding Oral Health Research Education Grants using the R25 mechanism to promote the application of basic and clinical research findings to clinical training and to encourage students to pursue careers in oral health research. This report describes the impact of an R25 grant awarded to the Texas A&M Health Science Center’s Baylor College of Dentistry (BCD) on its curriculum and faculty development efforts. At BCD, the R25 grant supports a multipronged initiative that employs clinical research as a vehicle for acquainting both students and faculty with the tools of evidence-based dentistry (EBD). New coursework and experiences in all four years of the curriculum plus a variety of faculty development offerings are being used to achieve this goal. Progress on these fronts is reflected in a nascent EBD culture characterized by increasing participation and buy-in by students and faculty. The production of a new generation of dental graduates equipped with the EBD skill set as well as a growing nucleus of faculty members who can model the importance of evidence-based practice is of paramount importance for the future of dentistry. PMID:21368252

Control of brushing variables for the in vitro assessment of toothpaste abrasivity using a novel laboratory model.

PubMed

Parry, Jason; Harrington, Edward; Rees, Gareth D; McNab, Rod; Smith, Anthony J

2008-02-01

Design and construct a tooth-brushing simulator incorporating control of brushing variables including brushing force, speed and temperature, thereby facilitating greater understanding of their importance in toothpaste abrasion testing methodologies. A thermostable orbital shaker was selected as a base unit and 16- and 24-specimen brushing rigs were constructed to fit inside, consisting of: a square bath partitioned horizontally to provide brushing channels, specimen holders for 25 mm diameter mounted specimens to fit the brushing channels and individually weighted brushing arms, able to support four toothbrush holders suspended over the brushing channels. Brush head holders consisted of individually weighted blocks of Delrin, or PTFE onto which toothbrush heads were fixed. Investigating effects of key design criteria involved measuring abrasion depths of polished human enamel and dentine. The brushing simulator demonstrated good reproducibility of abrasion on enamel and dentine across consecutive brushing procedures. Varying brushing parameters had a significant impact on wear results: increased brushing force demonstrated a trend towards increased wear, with increased reproducibility for greater abrasion levels, highlighting the importance of achieving sufficient wear to optimise accuracy; increasing brushing temperature demonstrated increased enamel abrasion for silica and calcium carbonate systems, which may be related to slurry viscosities and particle suspension; varying brushing speed showed a small effect on abrasion of enamel at lower brushing speed, which may indicate the importance of maintenance of the abrasive in suspension. Adjusting key brushing variables significantly affected wear behaviour. The brushing simulator design provides a valuable model system for in vitro assessment of toothpaste abrasivity and the influence of variables in a controlled manner. Control of these variables will allow more reproducible study of in vitro tooth wear processes.

Laser physics and a review of laser applications in dentistry for children.

PubMed

Martens, L C

2011-04-01

The aim of this introduction to this special laser issue is to describe some basic laser physics and to delineate the potential of laser-assisted dentistry in children. A brief review of the available laser literature was performed within the scope of paediatric dentistry. Attention was paid to soft tissue surgery, caries prevention and diagnosis, cavity preparation, comfort of the patient, effect on bacteria, long term pulpal vitality, endodontics in primary teeth, dental traumatology and low level laser therapy. Although there is a lack of sufficient evidence taking into account the highest standards for evidence-based dentistry, it is clear that laser application in a number of different aetiologies for soft tissue surgery in children has proven to be successful. Lasers provide a refined diagnosis of caries combined with the appropriate preventive adhesive dentistry after cavity preparation. This will further lead to a new wave of micro-dentistry based on 'filling without drilling'. It has become clear from a review of the literature that specific laser applications in paediatric dentistry have gained increasing importance. It can be concluded that children should be considered as amongst the first patients for receiving laser-assisted dentistry.

Practice of preventive dentistry for nursing staff in primary care

PubMed Central

Acuña-Reyes, Raquel; Cigarroa-Martínez, Didier; Ureña-Bogarín, Enrique; Orgaz-Fernández, Jose David

2014-01-01

Objectives: Determine the domain of preventive dentistry in nursing personnel assigned to a primary care unit. Methods: Prospective descriptive study, questionnaire validation, and prevalence study. In the first stage, the questionnaire for the practice of preventive dentistry (CPEP, for the term in Spanish) was validated; consistency and reliability were measured by Cronbach's alpha, Pearson's correlation, factor analysis with intra-class correlation coefficient (ICC). In the second stage, the domain in preventive dental nurses was explored. Results: The overall internal consistency of CPEP is α= 0.66, ICC= 0.64, CI95%: 0.29-0.87 (p >0.01). Twenty-one subjects in the study, average age 43, 81.0% female, average seniority of 12.5 were included. A total of 71.5% showed weak domain, 28.5% regular domain, and there was no questionnaire with good domain result. The older the subjects were, the smaller the domain; female nurses showed greater mastery of preventive dentistry (29%, CI95%: 0.1-15.1) than male nurses. Public health nurses showed greater mastery with respect to other categories (50%, CI95%: 0.56-2.8). Conclusions: The CDEP has enough consistency to explore the domain of preventive dentistry in health-care staff. The domain of preventive dentistry in primary care nursing is poor, required to strengthen to provide education in preventive dentistry to the insured population. PMID:25386037

Practice of preventive dentistry for nursing staff in primary care.

PubMed

Jiménez-Báez, María Valeria; Acuña-Reyes, Raquel; Cigarroa-Martínez, Didier; Ureña-Bogarín, Enrique; Orgaz-Fernández, Jose David

2014-01-01

Determine the domain of preventive dentistry in nursing personnel assigned to a primary care unit. Prospective descriptive study, questionnaire validation, and prevalence study. In the first stage, the questionnaire for the practice of preventive dentistry (CPEP, for the term in Spanish) was validated; consistency and reliability were measured by Cronbach's alpha, Pearson's correlation, factor analysis with intra-class correlation coefficient (ICC). In the second stage, the domain in preventive dental nurses was explored. The overall internal consistency of CPEP is α= 0.66, ICC= 0.64, CI95%: 0.29-0.87 (p >0.01). Twenty-one subjects in the study, average age 43, 81.0% female, average seniority of 12.5 were included. A total of 71.5% showed weak domain, 28.5% regular domain, and there was no questionnaire with good domain result. The older the subjects were, the smaller the domain; female nurses showed greater mastery of preventive dentistry (29%, CI95%: 0.1-15.1) than male nurses. Public health nurses showed greater mastery with respect to other categories (50%, CI95%: 0.56-2.8). The CDEP has enough consistency to explore the domain of preventive dentistry in health-care staff. The domain of preventive dentistry in primary care nursing is poor, required to strengthen to provide education in preventive dentistry to the insured population.

Monitoring of the Abrasion Processes (by the Example of Alakol Lake, Republic of Kazakhstan)

ERIC Educational Resources Information Center

Abitbayeva, Ainagul; Valeyev, Adilet; Yegemberdiyeva, Kamshat; Assylbekova, Aizhan; Ryskeldieva, Aizhan

2016-01-01

The purpose of the study is to analyze the abrasion processes in the regions of dynamically changing Alakol lake shores. Using the field method, methods of positioning by the GPS receiver and interpretation of remote sensing data, the authors determined that abrasion processes actively contributed to the formation the modern landscape, causing the…

Graduate and Undergraduate Geriatric Dentistry Education in a Selected Dental School in Japan

PubMed Central

Kitagawa, Noboru; Sato, Yuji; Komabayashi, Takashi

2010-01-01

Geriatric dentistry and its instruction are critical in a rapidly aging population. Japan is the world’s fastest-aging society, and thus geriatric dentistry education in Japan can serve as a global model for other countries that will soon encounter the issues that Japan has already confronted. This study aimed to evaluate geriatric dental education with respect to the overall dental education system, undergraduate geriatric dentistry curricula, mandatory internships, and graduate geriatric education of a selected dental school in Japan. Bibliographic data and local information were collected. Descriptive and statistical analyses (Fisher and Chi-square test) were conducted. Japanese dental schools teach geriatric dentistry in 10 geriatric dentistry departments as well as in prosthodontic departments. There was no significant differences found between the number of public and private dental schools with geriatric dentistry departments (p = 0.615). At Showa University School of Dentistry, there are more didactic hours than practical training hours; however, there is no significant didactic/practical hour distribution difference between the overall dental curriculum and fourth-year dental students’ geriatric dental education curriculum (p=0.077). Graduate geriatric education is unique because it is a four-year Ph.D. course of study; there is neither a Master’s degree program nor a certificate program in Geriatric Dentistry. Overall, both undergraduate and graduate geriatric dentistry curricula are multidisciplinary. This study contributes to a better understanding of geriatric dental education in Japan; the implications of this study include developing a clinical/didactic curriculum, designing new national/international dental public health policies, and calibrating the competency of dentists in geriatric dentistry. PMID:21985207

Gingival abrasion and recession in manual and oscillating-rotating power brush users.

PubMed

Rosema, N A M; Adam, R; Grender, J M; Van der Sluijs, E; Supranoto, S C; Van der Weijden, G A

2014-11-01

To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young adult participants: 90 manual brush users and 91 oscillating-rotating power brush users. Participants were assessed for GR and GA as primary response variables. Secondary response variables were the level of gingival inflammation, plaque score reduction and brushing duration. Pearson correlation was used to describe the relationship between number of recession sites and number of abrasions. Prebrushing (baseline) and post-brushing GA and plaque scores were assessed and differences analysed using paired tests. Two-sample t-test was used to analyse group differences; ancova was used for analyses of post-brushing changes with baseline as covariate. Overall, 97.8% of the study population had at least one site of ≥1 mm of gingival recession. For the manual group, this percentage was 98.9%, and for the power group, this percentage was 96.7% (P = 0.621). Post-brushing, the power group showed a significantly smaller GA increase than the manual group (P = 0.004); however, there was no significant correlation between number of recession sites and number of abrasions for either group (P ≥ 0.327). Little gingival recession was observed in either toothbrush user group; the observed GR levels were comparable. Lower post-brushing gingival abrasion levels were seen in the power group. There was no correlation between gingival abrasion as a result of brushing and the observed gingival recession following use of either toothbrush. © 2014 The Authors International Journal of Dental Hygiene Published by John Wiley & Sons Ltd.

The complexity of patient safety reporting systems in UK dentistry.

PubMed

Renton, T; Master, S

2016-10-21

Since the 'Francis Report', UK regulation focusing on patient safety has significantly changed. Healthcare workers are increasingly involved in NHS England patient safety initiatives aimed at improving reporting and learning from patient safety incidents (PSIs). Unfortunately, dentistry remains 'isolated' from these main events and continues to have a poor record for reporting and learning from PSIs and other events, thus limiting improvement of patient safety in dentistry. The reasons for this situation are complex.This paper provides a review of the complexities of the existing systems and procedures in relation to patient safety in dentistry. It highlights the conflicting advice which is available and which further complicates an overly burdensome process. Recommendations are made to address these problems with systems and procedures supporting patient safety development in dentistry.

Assessment of Rail Seat Abrasion Patterns and Environment

DOT National Transportation Integrated Search

2012-05-01

Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

Green dentistry: the art and science of sustainable practice.

PubMed

Mulimani, P

2017-06-23

Dentistry is highly energy and resource intensive with significant environmental impact. Factors inherent in the profession such as enormous electricity demands of electronic dental equipment, voluminous water requirements, environmental effects of biomaterials (before, during and after clinical use), the use of radiation and the generation of hazardous waste involving mercury, lead etc have contributed towards this. With rising temperatures across the world due to global warming, efforts are being made worldwide to mitigate the effects of environmental damage by resorting to sustainability concepts and green solutions in a myriad of ways. In such a scenario, a professional obligation and social responsibility of dentists makes it imperative to transform the practice of dentistry from a hazardous to a sustainable one, by adopting environmental-friendly measures or 'green dentistry'. The NHS in the UK has been proactive in implementing sustainability in healthcare by setting targets, developing guidance papers, initiating steering groups to develop measures and implementing actions through its Sustainable Development Unit (SDU). Such sustainable frameworks, specific to dentistry, are not yet available and even the scientific literature is devoid of studies in this field although anecdotal narratives abound. Hence this paper attempts to present a comprehensive evaluation of the existing healthcare sustainability principles, for their parallel application in the field of dentistry and lays out a blueprint for integrating the two main underlying principles of sustainability - resource use efficiency and eliminating or minimising pollution - in the day-to-day practice. The article also highlights the importance of social values, community care, engaging stakeholders, economic benefits, developing policy and providing leadership in converting the concept of green dentistry into a practised reality.

Methodological Quality of Consensus Guidelines in Implant Dentistry.

PubMed

Faggion, Clovis Mariano; Apaza, Karol; Ariza-Fritas, Tania; Málaga, Lilian; Giannakopoulos, Nikolaos Nikitas; Alarcón, Marco Antonio

2017-01-01

Consensus guidelines are useful to improve clinical decision making. Therefore, the methodological evaluation of these guidelines is of paramount importance. Low quality information may guide to inadequate or harmful clinical decisions. To evaluate the methodological quality of consensus guidelines published in implant dentistry using a validated methodological instrument. The six implant dentistry journals with impact factors were scrutinised for consensus guidelines related to implant dentistry. Two assessors independently selected consensus guidelines, and four assessors independently evaluated their methodological quality using the Appraisal of Guidelines for Research & Evaluation (AGREE) II instrument. Disagreements in the selection and evaluation of guidelines were resolved by consensus. First, the consensus guidelines were analysed alone. Then, systematic reviews conducted to support the guidelines were included in the analysis. Non-parametric statistics for dependent variables (Wilcoxon signed rank test) was used to compare both groups. Of 258 initially retrieved articles, 27 consensus guidelines were selected. Median scores in four domains (applicability, rigour of development, stakeholder involvement, and editorial independence), expressed as percentages of maximum possible domain scores, were below 50% (median, 26%, 30.70%, 41.70%, and 41.70%, respectively). The consensus guidelines and consensus guidelines + systematic reviews data sets could be compared for 19 guidelines, and the results showed significant improvements in all domain scores (p < 0.05). Methodological improvement of consensus guidelines published in major implant dentistry journals is needed. The findings of the present study may help researchers to better develop consensus guidelines in implant dentistry, which will improve the quality and trust of information needed to make proper clinical decisions.

Tribological properties of multifunctional coatings with Shape Memory Effect in abrasive wear

NASA Astrophysics Data System (ADS)

Blednova, Zh. M.; Dmitrenko, D. V.; Balaev, E. U. O.

2018-01-01

The article gives research results of the abrasive wear process on samples made of Steel 1045, U10 and with applied composite surface layer "Nickel-Multicomponent material with Shape Memory Effect (SME) based on TiNi". For the tests we have chosen TiNiZr, which is in the martensite state and TiNiHfCu, which is in the austenitic state at the test temperature. The formation of the surface layer was carried out by high-speed oxygen-fuel deposition in a protective atmosphere of argon. In the wear test, Al2O3 corundum powder was used as an abrasive. It is shown that the wear rate of samples with a composite surface layer of multicomponent materials with SME is significantly reduced in comparison with the base, which is explained by reversible phase transformations of the surface layer with SME. After carrying out the additional surface plastic deformation (SPD), the resistance of the laminated composition to abrasion wear has greatly enhanced, due to the reinforcing effect of the SPD. It is recommended for products working in conditions of abrasive wear and high temperatures to use the complex formation technology of the surface composition "steel-nickel-material with high-temperature SME", including preparation of the substrate surface and the deposited material, high-speed spraying in the protective atmosphere of argon, followed by SPD.

Scratching technique for the study and analysis of soil surface abrasion mechanism

NASA Astrophysics Data System (ADS)

Ta, Wanquan

2007-11-01

Aeolian abrasion is the most fundamental and active surface process that takes place in arid and semi-arid environments. Its nature is a wear process for wind blown grains impinging on a soil or sediment surface, which causes particles and aggregates to fracture from the soil surface through a series of plastic and brittle cracking deformation such as cutting, ploughing and brittle fracturing. Using a Universal Micro-Tribometer (UMT), a scratching test was carried out on six soil surfaces (sandy soil, sand loam, silt loam, loam, silt clay loam, and silt clay). The results indicate that traces of normal and tangential force vs. time show a jagged curve, which can reflect the plastic deformation and brittle fracturing of aggregates and particles of various sizes fractured from the soil surfaces. The jagged curve peaks, and the area enclosed underneath, may represent the bonding forces and bonding energies of some aggregates and grains on the soil surface, respectively. Connecting the scratching test with an impact abrasion experiment furthermore demonstrates that soil surface abrasion rates are proportional to the square of speeds of impacting particles and to the 2.6 power of mean soil grain size, and inversely proportional to the 1.5 power of specific surface abrasive energy or to the 1.7 power of specific surface hardness.

Resistance to abrasion of extrinsic porcelain esthetic characterization techniques.

PubMed

Chi, Woo J; Browning, William; Looney, Stephen; Mackert, J Rodway; Windhorn, Richard J; Rueggeberg, Frederick

2017-01-01

A novel esthetic porcelain characterization technique involves mixing an appropriate amount of ceramic colorants with clear, low-fusing porcelain (LFP), applying the mixture on the external surfaces, and firing the combined components onto the surface of restorations in a porcelain oven. This method may provide better esthetic qualities and toothbrush abrasion resistance compared to the conventional techniques of applying color-corrective porcelain colorants alone, or applying a clear glaze layer over the colorants. However, there is no scientific literature to support this claim. This research evaluated toothbrush abrasion resistance of a novel porcelain esthetic characterization technique by subjecting specimens to various durations of simulated toothbrush abrasion. The results were compared to those obtained using the conventional characterization techniques of colorant application only or colorant followed by placement of a clear over-glaze. Four experimental groups, all of which were a leucite reinforced ceramic of E TC1 (Vita A1) shade, were prepared and fired in a porcelain oven according to the manufacturer's instructions. Group S (stain only) was characterized by application of surface colorants to provide a definitive shade of Vita A3.5. Group GS (glaze over stain) was characterized by application of a layer of glaze over the existing colorant layer as used for Group S. Group SL (stain+LFP) was characterized by application of a mixture of colorants and clear low-fusing add-on porcelain to provide a definitive shade of Vita A3.5. Group C (Control) was used as a control without any surface characterization. The 4 groups were subjected to mechanical toothbrushing using a 1:1 water-to-toothpaste solution for a simulated duration of 32 years of clinical use. The amount of wear was measured at time intervals simulating every 4 years of toothbrushing. These parameters were evaluated longitudinally for all groups as well as compared at similar time points among

Nanotechnology in Dentistry: Clinical Applications, Benefits, and Hazards.

PubMed

Shashirekha, Govind; Jena, Amit; Mohapatra, Satyajit

2017-05-01

Nanotechnology is emerging as an interdisciplinary field that is undergoing rapid development and has brought about enormous changes in medicine and dentistry. Nanomaterial-based design is able to mimic some of the mechanical and structural properties of native tissue and can promote biointegration. Nanotechnology has various applications in dentistry, including dentition renaturalization, therapy for dentin hypersensitivity, complete orthodontic realignment in a single visit, covalently bonding diamondized enamel, enhancing properties of root canal sealers, and continuous oral health maintenance using mechanical dentifrobots. A range of synthetic nanoparticles such as hydroxyapatite, bioglass, titanium, zirconia, and silver nanoparticles are proposed for dental restoration. This review focuses on the developments in the field of nanomaterials in dentistry in the form of tissue regeneration materials, implantable devices, nanocomposites, endodontic sealers etc. and issues of patient safety.

Geriatric dentistry education and context in a selection of countries in 5 continents.

PubMed

Marchini, Leonardo; Ettinger, Ronald; Chen, Xi; Kossioni, Anastassia; Tan, Haiping; Tada, Sayaka; Ikebe, Kazunori; Dosumu, Elizabeth Bosede; Oginni, Fadekemi O; Akeredolu, Patricia Adetokunbo; Butali, Azeez; Donnelly, Leeann; Brondani, Mario; Fritzsch, Bernd; Adeola, Henry A

2018-05-01

To summarize and discuss how geriatric dentistry has been addressed in dental schools of different countries regarding to (1) teaching students at the predoctoral level; (2) advanced training, and (3) research. A convenience sample of faculty members from a selection of high, upper-middle and lower-middle income countries were recruited to complete the survey. The survey had 5 open-ended main topics, and asked about (1) the size of their elderly population, (2) general information about dental education; (3) the number of dental schools teaching geriatric dentistry, and their teaching methods; (4) advanced training in geriatric dentistry; (5) scholarship/research in geriatric dentistry. (1) There is great variation in the size of elderly population; (2) duration of training and content of dental education curriculum varies; (3) geriatric dentistry has not been established as a standalone course in dental schools in the majority of the countries, (4) most countries, with the exception of Japan, lack adequate number of dentists trained in geriatric dentistry as well as training programs, and (5) geriatric dentistry-related research has increased in recent years in scope and content, although the majority of these papers are not in English. © 2018 Special Care Dentistry Association and Wiley Periodicals, Inc.

Dependence of Non-Prestonian Behavior of Ceria Slurry with Anionic Surfactant on Abrasive Concentration and Size in Shallow Trench Isolation Chemical Mechanical Polishing

NASA Astrophysics Data System (ADS)

Kang, Hyun‑Goo; Kim, Dae‑Hyeong; Katoh, Takeo; Kim, Sung‑Jun; Paik, Ungyu; Park, Jea‑Gun

2006-05-01

The dependencies of the non-Prestonian behavior of ceria slurry with anionic surfactant on the size and concentration of abrasive particles were investigated by performing chemical mechanical polishing (CMP) experiments using blanket wafers. We found that not only the abrasive size but also the abrasive concentration with surfactant addition influences the non-Prestonian behavior. Such behavior is clearly exhibited with small abrasive sizes and a higher concentrations of abrasives with surfactant addition, because the abrasive particles can locally contact the film surface more effectively with applied pressure. We introduce a factor to quantify these relations with the non-Prestonian behavior of a slurry. For ceria slurry, this non-Prestonian factor, βNP, was determined to be almost independent of the abrasive concentration for a larger size and a smaller weight conentration of abrasive particles, but it increased with the surfactant concentration for a smaller size and a higher concentration of abrasives with surfactant addition.

Feasibility and Economics Study of the Treatment, Recycling and Disposal of Spent Abrasives

DTIC Science & Technology

1999-04-09

compression, and film stripping. The recycling performance testing plan is summarized in Table 2. (The test plan is discussed in detail in Appendix B: Law...D1188 Yes Yes Immersion Compression ................... ASTM C4867 Yes Yes Film Stripping................................... CalTrans 302 Yes Yes...from 10% to 20% for aluminum oxide abrasives, and 15% to 30% for garnet abrasives. 9 Data Intepretation SSPC-AB 1 requires that the conductivitiy of

The entrepreneurial role in primary care dentistry.

PubMed

Willcocks, S

2012-03-09

This paper explores the entrepreneurial role of dentists in primary care dentistry. It reviews the changing context of dentistry, not least the reforms being introduced by the health and social care bill. It suggests that this new context will reinforce the need to consider the business side of dental practice, in particular, the importance of quality, creativity and innovation, alongside the importance of meeting the needs of patients. An entrepreneurial approach will be required in order to sustain dental practice in an increasingly competitive environment.

Beginning the discussion of commercialism in dentistry.

PubMed

Boyd, Marcia A; Roth, Kathleen; Ralls, Stephen A; Chambers, David W

2008-01-01

There is increasing concern over commercialism in dentistry. Multiple factors contribute to this trend, which has the potential for fragmenting the profession, exacerbating the access issue, and eroding the public's confidence in dentistry. There are both positive and negative aspects of commercialism. Positive approaches for promoting oral health in the face of commercialism hold the greatest promise. The core theme in the recommendations from Ethics Summit on Commercialism is that competent, comprehensive, and continuous oral health care is appropriate and should be promoted to the American public.

Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

NASA Astrophysics Data System (ADS)

Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

2017-11-01

The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

[Polyethylene abrasion: cause or consequence of an endoprosthesis loosening? Investigations of firm and loosened hip implants].

PubMed

Busse, B; Niecke, M; Püschel, K; Delling, G; Katzer, A; Hahn, M

2007-01-01

Periprosthetic tissue was analysed by the combination of different investigation techniques without destruction. The localisation and geometry of polyethylene abrasion particles were determined quantitatively to differentiate between abrasion due to function and abrasion due to implant loosening. Non-polyethylene particles from implant components which contaminate the tissue were micro-analytically measured. The results will help us to understand loosening mechanisms and thus lead to implant optimisations. A non-destructive particle analysis using highly sensitive proton-induced X-ray emission (PIXE) was developed to achieve a better histological allocation. Five autopsy cases with firmly fitting hip endoprosthesis (2 x Endo-Modell Mark III, 1 x St. Georg Mark II, LINK, Germany; 2 x Spongiosa Metal II, ESKA, Germany) were prepared as ground tissue specimens. Wear investigations were accomplished with a combined application of different microscopic techniques and microanalysis. The abrasion due to implant loosening was histologically evaluated on 293 loosened cup implants (St. Georg Mark II, LINK, Germany). Wear particles are heterogeneously distributed in the soft tissue. In cases of cemented prostheses, cement particles are dominating whereas metal particles could rarely be detected. The concentration of the alloy constituent cobalt (Co) is increased in the mineralised bone tissue. The measured co-depositions depend on the localisation and/or lifetime of an implant. Functional polyethylene (PE) abrasion needs to be differentiated from PE abrasion of another genesis (loosening, impingement) morphologically and by different tissue reactions. In the past a reduction of abrasion was targeted primarily by the optimisation of the bearing surfaces and tribology. The interpretation of our findings indicates that different mechanisms of origin in terms of tissue contamination with wear debris and the alloy should be included in the improvement of implants or implantation

Erosion of enamel by non-carbonated soft drinks with and without toothbrushing abrasion.

PubMed

Hemingway, C A; Parker, D M; Addy, M; Barbour, M E

2006-10-07

To investigate how enamel loss due to erosion, and due to cycling of erosion and abrasion, depends on compositional parameters of soft drinks, and particularly whether the thickness of the erosive softened layer is a function of drink composition. University dental hospital research laboratory in the UK, 2004. Six drinks were chosen based on their popularity and composition: apple juice, orange juice, apple drink, orange drink, cranberry drink and 'ToothKind' blackcurrant drink. Group A samples (n = 36) were exposed to soft drinks at 36 degrees C for six consecutive 10 minute periods. Group B samples (n = 36) were subjected to alternating erosion and toothbrushing, repeated six times. Enamel loss was measured using optical profilometry. Group A: significant enamel loss was seen for all drinks (p < 0.001). Erosion was correlated with pH and calcium concentration but not phosphate concentration or titratable acidity. Group B: significant additional material loss due to toothbrush abrasion occurred with all drinks. Abrasive enamel loss differed between the drinks and was positively correlated with drink erosive potential. Enamel loss by erosion is exacerbated by subsequent abrasion. The amount of softened enamel removed by toothbrushing is a function of the chemical composition of the erosive medium.

Geriatric dentistry content in the curriculum of the dental schools in Chile.

PubMed

León, Soraya; Araya-Bustos, Francisca; Ettinger, Ronald L; Giacaman, Rodrigo A

2016-09-01

The purpose of this study was to identify the status of pre-doctoral geriatric dentistry education among all Chilean dental schools. Chile is one of the most rapidly ageing countries in Latin America. Consequently, specific knowledge and training on the needs of elderly populations need to be emphasised in dental schools. The current extent and methods of teaching geriatric dentistry among the dental schools in Chile are unknown. A web-based questionnaire was developed and sent to all 19 Chilean dental schools to identify which schools had a formal programme on geriatric dentistry and ask about their format, content and type of training of the faculty who taught in the programmes. Data were analysed, and a comparison was made among the schools. Sixteen (84%) of the participant schools reported teaching at least some aspects of geriatric dentistry, using various methodologies, but only 7 (37%) had specific courses. Of those schools reporting a didactic content on geriatric dentistry, 71% included clinical training, either in the school's dental clinics or in an extramural service. Contents mostly included demographics of ageing, theories of ageing and medical conditions. More than half of the faculty (57%) stated that they had formal training in geriatric dentistry, 43% were trained in prosthodontics, public health or other areas. Although most dental schools taught geriatric dentistry, only some had a specific course. Most schools with formal courses followed the international curriculum guidelines for geriatric dentistry. © 2014 John Wiley & Sons A/S and The Gerodontology Association. Published by John Wiley & Sons Ltd.

Comparison of cutting efficiencies between electric and air-turbine dental handpieces.

PubMed

Choi, Charlson; Driscoll, Carl F; Romberg, Elaine

2010-02-01

Dentistry is gravitating toward the increased use of electric handpieces. The dental professional should have sufficient evidence to validate the switch from an air-turbine handpiece to an electric handpiece. However, there is little research quantifying the cutting efficiency of electric and air-turbine handpieces. Studies that do quantify cutting efficiency typically do so with only a single material. The purpose of this study was to compare the cutting efficiency of an electric handpiece and an air-turbine handpiece, using various materials commonly used in dentistry. Seven materials: Macor (machinable glass ceramic), silver amalgam, aluminum oxide, zirconium oxide, high noble metal alloy, noble metal alloy, and base metal alloy, were each cut with a bur 220 times; 110 times with an electric handpiece, and 110 times with an air-turbine handpiece. The weight difference of the material was calculated by subtracting the weight of the material after a cut from the weight of the material before the cut. The cutting efficiency was calculated by dividing the weight difference by the duration of the cut (g/s). Data were analyzed by a 2-way analysis of variance followed by Tukey's Honestly Significant Difference (HSD) test (alpha=.05). The electric handpiece cut more efficiently than the air-turbine handpiece (F=3098.9, P<.001). In particular, the high noble metal alloy, silver amalgam, and Macor were cut more efficiently with the electric handpiece (0.0383 +/-0.0002 g/s, 0.0260 +/-0.0002 g/s, and 0.0122 +/-0.0002 g/s, respectively) than with the air-turbine handpiece (0.0125 +/-0.0002 g/s, 0.0142 +/-0.0002 g/s, and 0.008 +/-0.0002 g/s, respectively). The electric handpiece is more efficient at cutting various materials used in dentistry, especially machinable glass ceramic, silver amalgam, and high noble alloy, than the air-turbine handpiece.

Stem cells in dentistry--part I: stem cell sources.

PubMed

Egusa, Hiroshi; Sonoyama, Wataru; Nishimura, Masahiro; Atsuta, Ikiru; Akiyama, Kentaro

2012-07-01

Stem cells can self-renew and produce different cell types, thus providing new strategies to regenerate missing tissues and treat diseases. In the field of dentistry, adult mesenchymal stem/stromal cells (MSCs) have been identified in several oral and maxillofacial tissues, which suggests that the oral tissues are a rich source of stem cells, and oral stem and mucosal cells are expected to provide an ideal source for genetically reprogrammed cells such as induced pluripotent stem (iPS) cells. Furthermore, oral tissues are expected to be not only a source but also a therapeutic target for stem cells, as stem cell and tissue engineering therapies in dentistry continue to attract increasing clinical interest. Part I of this review outlines various types of intra- and extra-oral tissue-derived stem cells with regard to clinical availability and applications in dentistry. Additionally, appropriate sources of stem cells for regenerative dentistry are discussed with regard to differentiation capacity, accessibility and possible immunomodulatory properties. Copyright © 2012 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Methodological Quality of Consensus Guidelines in Implant Dentistry

PubMed Central

Faggion, Clovis Mariano; Apaza, Karol; Ariza-Fritas, Tania; Málaga, Lilian; Giannakopoulos, Nikolaos Nikitas; Alarcón, Marco Antonio

2017-01-01

Background Consensus guidelines are useful to improve clinical decision making. Therefore, the methodological evaluation of these guidelines is of paramount importance. Low quality information may guide to inadequate or harmful clinical decisions. Objective To evaluate the methodological quality of consensus guidelines published in implant dentistry using a validated methodological instrument. Methods The six implant dentistry journals with impact factors were scrutinised for consensus guidelines related to implant dentistry. Two assessors independently selected consensus guidelines, and four assessors independently evaluated their methodological quality using the Appraisal of Guidelines for Research & Evaluation (AGREE) II instrument. Disagreements in the selection and evaluation of guidelines were resolved by consensus. First, the consensus guidelines were analysed alone. Then, systematic reviews conducted to support the guidelines were included in the analysis. Non-parametric statistics for dependent variables (Wilcoxon signed rank test) was used to compare both groups. Results Of 258 initially retrieved articles, 27 consensus guidelines were selected. Median scores in four domains (applicability, rigour of development, stakeholder involvement, and editorial independence), expressed as percentages of maximum possible domain scores, were below 50% (median, 26%, 30.70%, 41.70%, and 41.70%, respectively). The consensus guidelines and consensus guidelines + systematic reviews data sets could be compared for 19 guidelines, and the results showed significant improvements in all domain scores (p < 0.05). Conclusions Methodological improvement of consensus guidelines published in major implant dentistry journals is needed. The findings of the present study may help researchers to better develop consensus guidelines in implant dentistry, which will improve the quality and trust of information needed to make proper clinical decisions. PMID:28107405

Contemporary undergraduate implant dentistry education: a systematic review.

PubMed

Koole, S; De Bruyn, H

2014-03-01

Consensus reports recommend that students upon graduation should possess a significant level of knowledge and competence in implant dentistry, including basic competences in diagnostics, treatment planning, restorative, straightforward surgical and maintenance procedures. In response, undergraduate curricula need to integrate implant dentistry. This narrative review explores educational programmes in terms of competences, related research and barriers or reflections, regarding implementation in undergraduate curricula. Publications (2008-2013) were searched systematically in WoS, PubMed and ERIC and screened independently by two authors in four stages: removal of duplicates, title screening, abstract screening and full-text reading. Inclusion criteria encompassed implant dentistry in undergraduate education. Finally, 37 of 420 papers were included. Detailed information regarding programme content, number of participants, staff input, logistics/funding issues is scattered. Theoretical education is predominant, and pre-clinical/clinical training is offered minimally, often carried out in elective programmes. However, selected straightforward cases treated by undergraduates yield positive outcomes with low failure rates, few complications, high patient satisfaction and student appreciation. Barriers to implementing implant dentistry in the undergraduate curriculum include funding issues, limitations in time or staff availability/competence and lack of suitable patients. Overcoming these barriers is worthwhile as experience-based implant education affects future practice as well-informed students propose more restorative alternatives to their patients. Although implant dentistry is increasingly integrated in undergraduate curricula, challenges remain in developing strategies to implement existing competence profiles and the extent of experience-based education. To support further advancement, universities should report comprehensively on their implant programmes to

Advanced functional polymers for regenerative and therapeutic dentistry.

PubMed

Lai, W-F; Oka, K; Jung, H-S

2015-07-01

Use of ceramics and polymers continues to dominate clinical procedures in modern dentistry. Polymers have provided the basis for adhesives, tissue void fillers, and artificial replacements for whole teeth. They have been remarkably effective in the clinic at restoration of major dental functions after damage or loss of teeth. With the rapid development of polymer science, dental materials science has significantly lagged behind in harnessing these advanced polymer products. What they offer is new and unique properties superior to traditional polymers and crucially a range of properties that more closely match natural biomaterials. Therefore, we should pursue more vigorously the benefits of advanced polymers in dentistry. In this review, we highlight how the latest generation of advanced polymers will enhance the application of materials in the dental clinic using numerous promising examples. Polymers have a broad range of applications in modern dentistry. Some major applications are to construct frameworks that mimic the precise structure of tissues, to restore tooth organ function, and to deliver bioactive agents to influence cell behavior from the inside. The future of polymers in dentistry must include all these new enhancements to increase biological and clinical effectiveness beyond what can be achieved with traditional biomaterials. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Healthcare-associated viral and bacterial infections in dentistry

PubMed Central

Laheij, A.M.G.A.; Kistler, J.O.; Belibasakis, G.N.; Välimaa, H.; de Soet, J.J.

2012-01-01

Infection prevention in dentistry is an important topic that has gained more interest in recent years and guidelines for the prevention of cross-transmission are common practice in many countries. However, little is known about the real risks of cross-transmission, specifically in the dental healthcare setting. This paper evaluated the literature to determine the risk of cross-transmission and infection of viruses and bacteria that are of particular relevance in the dental practice environment. Facts from the literature on HSV, VZV, HIV, Hepatitis B, C and D viruses, Mycobacterium spp., Pseudomonas spp., Legionella spp. and multi-resistant bacteria are presented. There is evidence that Hepatitis B virus is a real threat for cross-infection in dentistry. Data for the transmission of, and infection with, other viruses or bacteria in dental practice are scarce. However, a number of cases are probably not acknowledged by patients, healthcare workers and authorities. Furthermore, cross-transmission in dentistry is under-reported in the literature. For the above reasons, the real risks of cross-transmission are likely to be higher. There is therefore a need for prospective longitudinal research in this area, to determine the real risks of cross-infection in dentistry. This will assist the adoption of effective hygiene procedures in dental practice. PMID:22701774

29 CFR 1926.303 - Abrasive wheels and tools.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and tools. (a) Power. All grinding machines shall be supplied with sufficient power to maintain the spindle speed at safe levels under all conditions of normal operation. (b) Guarding. (1) Grinding machines..., nut, and outer flange may be exposed on machines designed as portable saws. (c) Use of abrasive wheels...

29 CFR 1926.303 - Abrasive wheels and tools.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and tools. (a) Power. All grinding machines shall be supplied with sufficient power to maintain the spindle speed at safe levels under all conditions of normal operation. (b) Guarding. (1) Grinding machines..., nut, and outer flange may be exposed on machines designed as portable saws. (c) Use of abrasive wheels...

29 CFR 1926.303 - Abrasive wheels and tools.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and tools. (a) Power. All grinding machines shall be supplied with sufficient power to maintain the spindle speed at safe levels under all conditions of normal operation. (b) Guarding. (1) Grinding machines..., nut, and outer flange may be exposed on machines designed as portable saws. (c) Use of abrasive wheels...

New UK graduates' knowledge of training and service provision within restorative dentistry - a survey.

PubMed

Kalsi, A S; Kochhar, S; Lewis, N J; Hemmings, K W

2017-06-09

Objective To assess new UK graduates' knowledge of training and service provision within restorative dentistry.Design A national descriptive cross-sectional survey.Subjects and methods An online survey assessing clinicians' knowledge of restorative dentistry, who had graduated within the last four years in the UK, was distributed across the UK via postgraduate dental deaneries. One-hundred responses were accepted as a sample of a potential population of 4,000.Main outcome measure How well respondents understood the service provision and training aspects of the specialty of restorative dentistry.Results The responses were received from graduates from a variety of dental schools across the UK. Of those respondents, 41 reported receiving career guidance within restorative dentistry. 45 new graduates were confident in their understanding of the specialty, while 53 were confident in the differences between restorative dentistry and monospecialty training. The respondents appeared unaware regarding treatment priorities within restorative dentistry departments. Most respondents felt that receiving teaching on restorative dentistry as a specialty and career pathway would be beneficial.Conclusion The results suggest that new graduates may benefit from clarification regarding the specialty of restorative dentistry, however, caution must be taken due to the limitations of the study.

Abrasion Resistance of Nano Silica Modified Roller Compacted Rubbercrete: Cantabro Loss Method and Response Surface Methodology Approach

NASA Astrophysics Data System (ADS)

Adamu, Musa; Mohammed, Bashar S.; Shafiq, Nasir

2018-04-01

Roller compacted concrete (RCC) when used for pavement is subjected to skidding/rubbing by wheels of moving vehicles, this causes pavement surface to wear out and abrade. Therefore, abrasion resistance is one of the most important properties of concern for RCC pavement. In this study, response surface methodology was used to design, evaluate and analyze the effect of partial replacement of fine aggregate with crumb rubber, and addition of nano silica on the abrasion resistance of roller compacted rubbercrete (RCR). RCR is the terminology used for RCC pavement where crumb rubber was used as partial replacement to fine aggregate. The Box-Behnken design method was used to develop the mixtures combinations using 10%, 20%, and 30% crumb rubber with 0%, 1%, and 2% nano silica. The Cantabro loss method was used to measure the abrasion resistance. The results showed that the abrasion resistance of RCR decreases with increase in crumb rubber content, and increases with increase in addition of nano silica. The analysis of variance shows that the model developed using response surface methodology (RSM) has a very good degree of correlation, and can be used to predict the abrasion resistance of RCR with a percentage error of 5.44%. The combination of 10.76% crumb rubber and 1.59% nano silica yielded the best combinations of RCR in terms of abrasion resistance of RCR.

The era of whiter teeth: advertising in American dentistry 1910-1950.

PubMed

Grumsen, Stine

2009-01-01

It has often been argued that the public image of dentists has been tainted by association with fear and pain into an image of evil 'psychodontists' and that there is an apparent lack of 'role models' in popular film, television, art and literature concerned with dentistry. This paper argues that we get a different picture when looking at different media. Advertisements introduce into a public domain, positive images of dentistry which crucially differ from the images found in other popular media. This paper traces the public image of dentistry in early 20th-century America, as seen through dentifrice advertisements, and suggests three important reasons for studying advertisements: First, advertisements provide a supplement to studies of popular images of dentistry carried out so far. Second, advertisements have played an important part in advancing oral hygiene as a public concern. And third, advertisements provide the historian of dentistry with a unique opportunity for analyzing the complex and interwoven relationship of popular and professional discourses, since ads have acted as catalysts for professional discussions and self-reflection among dentists.

Rock Cutting Depth Model Based on Kinetic Energy of Abrasive Waterjet

NASA Astrophysics Data System (ADS)

Oh, Tae-Min; Cho, Gye-Chun

2016-03-01

Abrasive waterjets are widely used in the fields of civil and mechanical engineering for cutting a great variety of hard materials including rocks, metals, and other materials. Cutting depth is an important index to estimate operating time and cost, but it is very difficult to predict because there are a number of influential variables (e.g., energy, geometry, material, and nozzle system parameters). In this study, the cutting depth is correlated to the maximum kinetic energy expressed in terms of energy (i.e., water pressure, water flow rate, abrasive feed rate, and traverse speed), geometry (i.e., standoff distance), material (i.e., α and β), and nozzle system parameters (i.e., nozzle size, shape, and jet diffusion level). The maximum kinetic energy cutting depth model is verified with experimental test data that are obtained using one type of hard granite specimen for various parameters. The results show a unique curve for a specific rock type in a power function between cutting depth and maximum kinetic energy. The cutting depth model developed here can be very useful for estimating the process time when cutting rock using an abrasive waterjet.

Toothbrush abrasion of paint-on resins for shade modification and crown resins: effect of water absorption.

PubMed

Fujii, Koichi; Arikawa, Hiroyuki; Kanie, Takahito; Ban, Seiji

2004-06-01

In order to investigate the clinical application of paint-on resins, the effect of water absorption on toothbrush abrasion and light transmittance of ten crown resins including three paint-on resins was examined. Water absorption into each material ranged from 0.29 to 0.89 mg/cm2 after storage in distilled-water for 6 weeks and their hardnesses decreased by 3.5-22.3%. Maximum surface roughness (Rmax) of the materials stored in distilled water for 6 weeks increased with an increasing number of toothbrush abrasion cycles and ranged from 1.9 to 10.5 microm after 100,000 cycles. Also, Maximum depth and weight loss as an indicator of the amount of each material lost by abrasion showed similar behaviors similar to Rmax. These results indicated that the abrasion resistance of paint-on resins was located in the middle among all materials examined.

The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way

PubMed Central

Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

2013-01-01

Objective. To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Materials and methods. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then correlated to each other. An unpaired t-test for the difference in the abrasion values between the toothpastes and the abrasion values over time was used. Results. The polishing paste RDA® 170 yielded higher Ra-values than RDA 250®, both after 1 and 6 h of brushing (1.01 ± 0.22 and 8.99 ± 1.55 compared to 0.63 ± 0.26 and 7.83 ± 5.89, respectively) as well as volume loss values (3.71 ± 0.17 and 20.20 ± 2.41 compared to 2.15 ± 1.41 and 14.79 ± 11.76, respectively), thus poor correlations between the RDA and Ra and Volume loss values were shown. Among the toothpastes, Apotekets® showed the highest Ra value after 1 h of brushing and Pepsodent® whitening after 6 h of brushing. Pepsodent® whitening also showed the highest volume loss values, both after 1 and 6 h of brushing. Conclusion. This study emphasizes the importance of not only considering the RDA value, but also a roughness value, when describing the abrasivity of a toothpaste. Furthermore, it can be concluded that so called ‘whitening' toothpastes do not necessarily have a higher abrasive effect than other toothpastes. PMID:22746180

The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way.

PubMed

Johannsen, Gunnar; Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

2013-01-01

To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then correlated to each other. An unpaired t-test for the difference in the abrasion values between the toothpastes and the abrasion values over time was used. The polishing paste RDA® 170 yielded higher Ra-values than RDA 250®, both after 1 and 6 h of brushing (1.01 ± 0.22 and 8.99 ± 1.55 compared to 0.63 ± 0.26 and 7.83 ± 5.89, respectively) as well as volume loss values (3.71 ± 0.17 and 20.20 ± 2.41 compared to 2.15 ± 1.41 and 14.79 ± 11.76, respectively), thus poor correlations between the RDA and Ra and Volume loss values were shown. Among the toothpastes, Apotekets® showed the highest Ra value after 1 h of brushing and Pepsodent® whitening after 6 h of brushing. Pepsodent® whitening also showed the highest volume loss values, both after 1 and 6 h of brushing. This study emphasizes the importance of not only considering the RDA value, but also a roughness value, when describing the abrasivity of a toothpaste. Furthermore, it can be concluded that so called 'whitening' toothpastes do not necessarily have a higher abrasive effect than other toothpastes.

Effect of etching and airborne particle abrasion on the microstructure of different dental ceramics.

PubMed

Borges, Gilberto Antonio; Sophr, Ana Maria; de Goes, Mario Fernando; Sobrinho, Lourenço Correr; Chan, Daniel C N

2003-05-01

The ceramic composition and microstructure surface of all-ceramic restorations are important components of an effective bonding substrate. Both hydrofluoric acid etching and airborne aluminum oxide particle abrasion produce irregular surfaces necessary for micromechanical bonding. Although surface treatments of feldspathic and leucite porcelains have been studied previously, the high alumina-containing and lithium disilicate ceramics have not been fully investigated. The purpose of this study was to assess the surface topography of 6 different ceramics after treatment with either hydrofluoric acid etching or airborne aluminum oxide particle abrasion. Five copings each of IPS Empress, IPS Empress 2 (0.8 mm thick), Cergogold (0.7 mm thick), In-Ceram Alumina, In-Ceram Zirconia, and Procera (0.8 mm thick) were fabricated following the manufacturer's instructions. Each coping was longitudinally sectioned into 4 equal parts by a diamond disk. The resulting sections were then randomly divided into 3 groups depending on subsequent surface treatments: Group 1, specimens without additional surface treatments, as received from the laboratory (control); Group 2, specimens treated by use of airborne particle abrasion with 50-microm aluminum oxide; and Group 3, specimens treated with 10% hydrofluoric acid etching (20 seconds for IPS Empress 2; 60 seconds for IPS Empress and Cergogold; and 2 minutes for In-Ceram Alumina, In-Ceram Zirconia, and Procera). Airborne particle abrasion changed the morphologic surface of IPS Empress, IPS Empress 2, and Cergogold ceramics. The surface topography of these ceramics exhibited shallow irregularities not evident in the control group. For Procera, the 50-microm aluminum oxide airborne particle abrasion produced a flattened surface. Airborne particle abrasion of In-Ceram Alumina and In-Ceram Zirconia did not change the morphologic characteristics and the same shallows pits found in the control group remained. For IPS Empress 2, 10% hydrofluoric

The effect of frontal air bags on eye injury patterns in automobile crashes.

PubMed

Duma, Stefan M; Jernigan, M Virginia; Stitzel, Joel D; Herring, Ian P; Crowley, John S; Brozoski, Fred T; Bass, Cameron R

2002-11-01

To investigate eye injuries resulting from frontal automobile crashes and to determine the effects of frontal air bags. The National Automotive Sampling System database files from January 1, 1993, through December 31, 1999, were examined in a 3-part study that included an investigation of 22 236 individual crashes that occurred in the United States. A new 4-level eye injury severity scale that quantifies injuries based on recovery time, need for surgery, and possible loss of sight was developed. Of all occupants who were exposed to an air bag deployment, 3% sustained an eye injury. In contrast, 2% of occupants not exposed to an air bag deployment sustained an eye injury. A closer examination of the type of eye injuries showed that there was a statistically significant increase in the risk of corneal abrasions for occupants who were exposed to an air bag compared with those who were not (P =.03). Of occupants exposed to an air bag deployment, 0.5% sustained a corneal abrasion compared with 0.04% of occupants who were not exposed to an air bag. Using the new injury levels, it was shown that although occupants exposed to an air bag deployment had a higher risk of sustaining minor eye injuries, the air bag appears to have provided a beneficial exchange by reducing the number of severe eye injuries.

Errors in dentistry: a call for apology.

PubMed

Schwartz, Barry

2005-01-01

Bad outcomes occur in dentistry and sometimes these are the results of dental errors. In both cases, this essay will argue that apologies are very important in maintaining a relationship with the patient that is based on trust and mutual respect. Nevertheless, apologies are often not forthcoming in dentistry for a number of reasons that deserve careful examination. In particular, the dentist's fear that an apology will increase the risk of legal harm will be critiqued. Ethical and psychological reasons for making an apology will be discussed, and strategies to assist clinicians in making an apology will be offered.

Victorian era esthetic and restorative dentistry: an advertising trade card gallery.

PubMed

Croll, Theodore P; Swanson, Ben Z

2006-01-01

A chief means of print advertising in the Victorian era was the "trade card." Innumerable products, companies, and services were highlighted on colorful chromolithographic trade cards, and these became desirable collectible objects which were pasted into scrapbooks and enjoyed by many families. Dentistry- and oral health-related subjects were often depicted on Victorian trade cards, and esthetic and restorative dentistry themes were featured. This review describes the history of advertising trade cards and offers a photographic gallery of dentistry-related cards of the era.

Sliding-gate valve for use with abrasive materials

DOEpatents

Ayers, Jr., William J.; Carter, Charles R.; Griffith, Richard A.; Loomis, Richard B.; Notestein, John E.

1985-01-01

The invention is a flow and pressure-sealing valve for use with abrasive solids. The valve embodies special features which provide for long, reliable operating lifetimes in solids-handling service. The valve includes upper and lower transversely slidable gates, contained in separate chambers. The upper gate provides a solids-flow control function, whereas the lower gate provides a pressure-sealing function. The lower gate is supported by means for (a) lifting that gate into sealing engagement with its seat when the gate is in its open and closed positions and (b) lowering the gate out of contact with its seat to permit abrasion-free transit of the gate between its open and closed positions. When closed, the upper gate isolates the lower gate from the solids. Because of this shielding action, the sealing surface of the lower gate is not exposed to solids during transit or when it is being lifted or lowered. The chamber containing the lower gate normally is pressurized slightly, and a sweep gas is directed inwardly across the lower-gate sealing surface during the vertical translation of the gate.

Quality in restorative dentistry: a report of an advanced postgraduate dental symposium.

PubMed

Wilson, N H

1996-08-01

A joint Royal College of Surgeons of Edinburgh--Royal College of Physicians and Surgeons of Glasgow Advanced Postgraduate Dental Symposium addressed the issue of quality in restorative dentistry. The overall view was that quality in clinical care, including all aspects of restorative dentistry, is the consistent achievement of successful outcome. Ongoing developments and effective audit processes were recognized to provide important opportunities for continuous quality improvement in restorative dentistry.

Investigating selective transport and abrasion on an alluvial fan using quantitative grain size and shape analysis

NASA Astrophysics Data System (ADS)

Litwin, K. L.; Jerolmack, D. J.

2011-12-01

Selective sorting and abrasion are the two major fluvial processes that are attributed to the downstream fining of sediments in rivers and alluvial fans. Selective transport is the process by which smaller grains are preferentially transported downstream while larger grains are deposited closer to the source. Abrasion is defined by the production of fine sediments and sand that occurs by saltation of gravel, where particle-to-particle collisions supply the energy required to break apart grains. We hypothesize that abrasion results in the gradual fining of large grains and the production of fine sands and silts, while sorting accounts for the differences in transport of these two grain-size fractions produced from abrasion, thereby creating the abrupt gravel-sand transition observed in many channel systems. In this research, we explore both selective transport and abrasion processes on the Dog Canyon alluvial fan near Alamogordo, New Mexico. We complete an extensive grain size analysis down the main channel of the fan employing an image-based technique that utilizes an autocorrelation process. We also characterize changes in grain shape using standard shape parameters, as well as Fourier analysis, which allows the study of contributions of grain roughness on a variety of length scales. Sorting appears to dominate the upper portion of the fan; the grain-size distribution narrows moving downstream until reaching a point of equal mobility, at which point sorting ceases. Abrasion exerts a subtle but persistent effect on grains during transport down the fan. Shape analysis reveals that particles become more rounded by the removal of small-scale textural features, a process that is expected to only modestly influence grain size of gravel, but should produce significant quantities of sand. This study provides a better understanding of the importance of grain abrasion and sorting on the downstream fining of channel grains in an alluvial fan, as well as an improved knowledge

Abrasion-Resistant Coating for Flexible Insulation

NASA Technical Reports Server (NTRS)

Mui, D.; Headding, R. E.

1986-01-01

Ceramic coating increases durability and heat resistance of flexible high-temperature insulation. Coating compatible with quartz-fabric insulation allowing it to remain flexible during and after repeated exposures to temperatures of 1,800 degree F (982 degree C). Prevents fabric from becoming brittle while increasing resistance to aerodynamic abrasion and loading. Coating consists of penetrating precoat and topcoat. Major ingredients high-purity colloidal silica binder and ground silica filler, which ensure stability and compatibility with fabric at high temperatures. Both precoat and topcoat cured at room temperature.

An evaluation of the effects of handpiece speed, abrasive characteristics, and polishing load on the flexural strength of polished ceramics.

PubMed

Ahmad, Rohana; Morgano, Steven M; Wu, Benjamin M; Giordano, Russell A

2005-11-01

Many studies on the strengthening effects of grinding and polishing, as well as heat treatment on ceramics, are not well standardized or use commercially available industrial polishing systems. The reported effectiveness of these strengthening mechanisms on ceramics may not be applicable to clinical dentistry. The purpose of this study was to evaluate the effects of controlled polishing on the flexural strength of dental ceramics by using a custom-made machine that applied standardized loads and speeds that coincided with the mean loads and speeds used by experienced prosthodontists. A total of 140 aluminous dental ceramic bar-shaped specimens (Vitadur Alpha Enamel) measuring 1.5 x 2.0 x 25 mm were fabricated and divided into 12 groups (for most groups, n=10). Specimens were untreated, polished with different polishing systems, polished at different speeds, ground and autoglazed, polished and autoglazed, autoglazed and polished, polished with loose (paste) and bonded abrasives, or overglazed. Simulated clinical polishing was performed on the ceramic specimens by using a customized polishing apparatus that allowed independent control over the relevant polishing parameters (abrasive hardness, applied load, linear speed, rotational velocity, and wheel stiffness). Flexural strength (MPa) was measured with a 4-point bending test, and subjective surface roughness was assessed with scanning electron microscopy. Autoglazing was performed at various stages of the polishing sequence to determine the effects of polishing on surface stresses. Mean values, standard deviations, independent-sample t tests, 1-way and 2-way analyses of variance, Dunnett t tests and Kruskal-Wallis tests were applied to the data (alpha=.05). Under a clinical load of 0.6 N for a coarse polishing wheel, 1.0 N for a medium polishing wheel, and 1.3 N for a fine polishing wheel, a linear speed of 499 mm/min, and a rotational velocity of 10,000 rpm, the use of clinical polishing instruments did not affect

The application of ozone in dentistry: a systematic review of literature.

PubMed

Azarpazhooh, Amir; Limeback, Hardy

2008-02-01

(1) To systematically review the clinical application and remineralization potentials of ozone in dentistry; (2) To summarize the available in vitro applications of ozone in dentistry. Ovid MEDLINE, CINAHL, etc. (up to April 2007). In vitro or in vivo English language publications, original studies, and reviews were included. Conference papers, abstracts, and posters were excluded. In vitro: Good evidence of ozone biocompatibility with human oral epithelial cells, gingival fibroblast, and periodontal cells; Conflicting evidence of antimicrobial efficacy of ozone but some evidence that ozone is effective in removing the microorganisms from dental unit water lines, the oral cavity, and dentures; Conflicting evidence for the application of ozone in endodontics; Insufficient evidence for the application of ozone in oral surgery and implantology; Good evidence of the prophylactic application of ozone in restorative dentistry prior to etching and the placement of dental sealants and restorations. In vivo: Despite the promising in vitro evidence, the clinical application of ozone in dentistry (so far in management of dental and root caries) has not achieved a strong level of efficacy and cost-effectiveness. While laboratory studies suggest a promising potential of ozone in dentistry, this has not been fully realised in clinical studies to date. More well designed and conducted double-blind randomised clinical trials with adequate sample size, limited or no loss to follow up, and carefully standardised methods of measurement and analyses are needed to evaluate the possible use of ozone as a treatment modality in dentistry.

Abrasive wear behavior of in-situ RZ5-10wt%TiC composite

NASA Astrophysics Data System (ADS)

Mehra, Deepak; Mahapatra, M. M.; Harsha, S. P.

2018-05-01

RZ5 Magnesium alloys containing zinc, rare earth and zirconium are well-known to have high specific strength, good creep resistance widely used in aerospace components. The incorporation of hard ceramic strengthens RZ5 mg alloy. The RZ5-10wt%TiC composite has been fabricated in situ using RZ5 mg alloy as matrix and TiC as reinforcement by self propagating high temperature synthesis (SHS) technique. This paper investigates the abrasive wear behavior of RZ5-10wt%TiC. Tests were performed using pin-on-disc apparatus against 600 grit abrasive paper by varying the sliding distance and applied load. The results showed improvement in the wear resistance of testing composite as compared to the unreinforced RZ5 Mg alloy. The coefficient of friction and weight loss increased linearly as applied load and sliding distance increased. The field emission scanning electron microscopic (FESEM) showed dominate wear mechanisms: abrasion, ploughing grooves.

Evidence-based dentistry: a clinician's perspective.

PubMed

Bauer, Janet; Spackman, Sue; Chiappelli, Francesco; Prolo, Paolo; Stevenson, Richard

2006-07-01

Evidence-based dentistry is a discipline that provides best, explicit-based evidence to dentists and their patients in shared decision-making. Currently, dentists are being trained and directed to adopt the role of translational researchers in developing evidence-based dental practices. Practically, evidence-based dentistry is not usable in its current mode for the provision of labor-intensive services that characterize current dental practice. The purpose of this article is to introduce a model of evidence-based dental practice. This model conceptualizes a team approach in explaining problems and solutions to change current dental practice. These changes constitute an evidence-based dental practice that involves the electronic chart, centralized database, knowledge management software, and personnel in optimizing effective oral health care to dental patients.

Abrasion Resistance and Mechanical Properties of Waste-Glass-Fiber-Reinforced Roller-compacted Concrete

NASA Astrophysics Data System (ADS)

Yildizel, S. A.; Timur, O.; Ozturk, A. U.

2018-05-01

The potential use of waste glass fibers in roller-compacted concrete (RCC) was investigated with the aim to improve its performance and reduce environmental effects. The research was focused on the abrasion resistance and compressive and flexural strengths of the reinforced concrete relative to those of reference mixes without fibers. The freeze-thaw resistance of RCC mixes was also examined. It was found that the use of waste glass fibers at a rate of 2 % increased the abrasion resistance of the RCC mixes considerably.

9 CFR 311.14 - Abrasions, bruises, abscesses, pus, etc.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Abrasions, bruises, abscesses, pus, etc. 311.14 Section 311.14 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT... AND VOLUNTARY INSPECTION AND CERTIFICATION DISPOSAL OF DISEASED OR OTHERWISE ADULTERATED CARCASSES AND...

Abrasion resistant coating and method of making the same

DOEpatents

Sordelet, Daniel J.; Besser, Matthew F.

2001-06-05

An abrasion resistant coating is created by adding a ductile phase to a brittle matrix phase during spray coating where an Al--Cu--Fe quasicrystalline phase (brittle matrix) and an FeAl intermetallic (ductile phase) are combined. This composite coating produces a coating mostly of quasicrystal phase and an inter-splat layer of the FeAl phase to help reduce porosity and cracking within the coating. Coatings are prepared by plasma spraying unblended and blended quasicrystal and intermetallic powders. The blended powders contain 1, 5, 10 and 20 volume percent of the intermetallic powders. The unblended powders are either 100 volume percent quasicrystalline or 100 volume percent intermetallic; these unblended powders were studied for comparison to the others. Sufficient ductile phase should be added to the brittle matrix to transform abrasive wear mode from brittle fracture to plastic deformation, while at the same time the hardness of the composite should not be reduced below that of the original brittle phase material.

Defining an Abrasion Index for Lunar Surface Systems as a Function of Dust Interaction Modes and Variable Concentration Zones

NASA Technical Reports Server (NTRS)

Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

2010-01-01

Unexpected issues were encountered during the Apollo era of lunar exploration due to detrimental abrasion of materials upon exposure to the fine-grained, irregular shaped dust on the surface of the Moon. For critical design features involving contact with the lunar surface and for astronaut safety concerns, operational concepts and dust tolerance must be considered in the early phases of mission planning. To systematically define material selection criteria, dust interaction can be characterized by two-body or three-body abrasion testing, and subcategorically by physical interactions of compression, rolling, sliding and bending representing specific applications within the system. Two-body abrasion occurs when a single particle or asperity slides across a given surface removing or displacing material. Three-body abrasion occurs when multiple particles interact with a solid surface, or in between two surfaces, allowing the abrasives to freely rotate and interact with the material(s), leading to removal or displacement of mass. Different modes of interaction are described in this paper along with corresponding types of tests that can be utilized to evaluate each configuration. In addition to differential modes of abrasion, variable concentrations of dust in different zones can also be considered for a given system design and operational protocol. These zones include: (1) outside the habitat where extensive dust exposure occurs, (2) in a transitional zone such as an airlock or suitport, and (3) inside the habitat or spacesuit with a low particle count. These zones can be used to help define dust interaction frequencies, and corresponding risks to the systems and/or crew can be addressed by appropriate mitigation strategies. An abrasion index is introduced that includes the level of risk, R, the hardness of the mineralogy, H, the severity of the abrasion mode, S, and the frequency of particle interactions, F.

Development of Prototype Outcomes-Based Training Modules for Aesthetic Dentistry

ERIC Educational Resources Information Center

Andres, Maricar Joy T.; Borabo, Milagros L.

2015-01-01

The objective of the study is to know the essential components of Aesthetic Dentistry that will be a basis for prototype Outcomes-based training modules. Using a 5-point Likert scale, the researcher-made questionnaire assessed the different elements of Aesthetic Dentistry which are needed in the designing of the training module, the manner of…

Entrepreneurial Knowledge and Aspirations of Dentistry Students in South Africa

ERIC Educational Resources Information Center

Brijlal, Pradeep; Brijlal, Priscilla

2013-01-01

An investigation of the intentions and knowledge of entrepreneurship of final-year university dentistry students is reported, with particular regard to the factors of gender and race. A questionnaire survey was used with final-year dentistry students, over two years, at the University of the Western Cape in South Africa. The findings show that…

Abrasion-resistant concrete mix designs for precast bridge deck panels.

DOT National Transportation Integrated Search

2010-08-01

The report documents laboratory investigations undertaken to develop high performance concrete (HPC) for precast and pre-stressed bridge deck components that would reduce the life-cycle cost of bridges by improving the studded tire wear (abrasion) re...

Influence of different toothpaste abrasives on the bristle end-rounding quality of toothbrushes.

PubMed

de Oliveira, G J P L; de Aveiro, J M; Pavone, C; Marcantonio, R A C

2015-02-01

To evaluate the influence of different toothpaste abrasives on the bristle wear and bristle tip morphology of toothbrushes with different degrees of hardness. Ninety samples of bovine incisor teeth were used in this study. The samples were randomly divided into three groups according to the bristle hardness of the toothbrush used: soft bristles (S); extra-soft bristles (ES); hard bristles (H). The toothbrushes of each group were randomly divided into six subgroups with five toothbrushes each, according to the abrasive of the toothpaste used in the simulation: Negative control (distilled water); toothpaste 1 (silica); toothpaste 2 (hydrated silica); toothpaste 3 (calcium carbonate, calcium bicarbonate and silica); toothpaste 4 (tetrapotassium pyrophosphate, silica and titanium dioxide); toothpaste 5 (calcium carbonate). The samples were placed in a toothbrushing simulating machine that simulating three months of brushing. The toothbrush bristles were evaluated by the bristle wear index, and the bristle tips morphology was evaluated by the bristle tip morphology index. The ES brush presented the highest bristle wear among the toothbrushes. Additionally, the S brushes showed better morphology of the bristles followed by ES and H brushes. The type of abrasive only influenced the bristle tip morphology of the ES brushes. The toothpaste 3 induced the worse bristle tip morphology than all the other toothpastes. Different abrasives have influence only on the bristle tip morphology of the ES brushes. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Sequential analysis applied to clinical trials in dentistry: a systematic review.

PubMed

Bogowicz, P; Flores-Mir, C; Major, P W; Heo, G

2008-01-01

Clinical trials employ sequential analysis for the ethical and economic benefits it brings. In dentistry, as in other fields, resources are scarce and efforts are made to ensure that patients are treated ethically. The objective of this systematic review was to characterise the use of sequential analysis for clinical trials in dentistry. We searched various databases from 1900 through to January 2008. Articles were selected for review if they were clinical trials in the field of dentistry that had applied some form of sequential analysis. Selection was carried out independently by two of the authors. We included 18 trials from various specialties, which involved many different interventions. We conclude that sequential analysis seems to be underused in this field but that there are sufficient methodological resources in place for future applications.Evidence-Based Dentistry (2008) 9, 55-62. doi:10.1038/sj.ebd.6400587.

Consumer-driven and commercialised practice in dentistry: an ethical and professional problem?

PubMed

Holden, A C L

2018-03-20

The rise and persistence of a commercial model of healthcare and the potential shift towards the commodification of dental services, provided to consumers, should provoke thought about the nature and purpose of dentistry and whether this paradigm is cause for concern. Within this article, whether dentistry is a commodity and the legitimacy of dentistry as a business is explored and assessed. Dentistry is perceived to be a commodity, dependent upon the context of how services are to be provided and the interpretation of the patient-professional relationship. Commercially-focused practices threaten the fiduciary nature of the interaction between consumer and provider. The solution to managing commercial elements within dentistry is not through rejection of the new paradigm of the consumer of dental services, but in the rejection of competitive practices, coercive advertising and the erosion of professional values and duty. Consumerism may bring empowerment to those accessing dental services. However, if the patient-practitioner relationship is reduced to a mere transaction in the name of enhanced consumer participation, this empowerment is but a myth.

Topical non-steroidal anti-inflammatory drugs for analgesia in traumatic corneal abrasions.

PubMed

Wakai, Abel; Lawrenson, John G; Lawrenson, Annali L; Wang, Yongjun; Brown, Michael D; Quirke, Michael; Ghandour, Omar; McCormick, Ryan; Walsh, Cathal D; Amayem, Ahmed; Lang, Eddy; Harrison, Nick

2017-05-18

Traumatic corneal abrasions are relatively common and there is a lack of consensus about analgesia in their management. It is therefore important to document the clinical efficacy and safety profile of topical ophthalmic non-steroidal anti-inflammatory drugs (NSAIDs) in the management of traumatic corneal abrasions. To identify and evaluate all randomised controlled trials (RCTs) comparing the use of topical NSAIDs with placebo or any alternative analgesic interventions in adults with traumatic corneal abrasions (including corneal abrasions arising from foreign body removal), to reduce pain, and its effects on healing time. We searched the Cochrane Central Register of Controlled Trials (CENTRAL) (which contains the Cochrane Eyes and Vision Trials Register) (2017, Issue 2), MEDLINE Ovid (1946 to 30 March 2017), Embase Ovid (1947 to 30 March 2017), LILACS (Latin American and Caribbean Health Sciences Literature Database) (1982 to 30 March 2017), OpenGrey (System for Information on Grey Literature in Europe) (www.opengrey.eu/); searched 30 March 2017, ZETOC (1993 to 30 March 2017), the ISRCTN registry (www.isrctn.com/editAdvancedSearch); searched 30 March 2017, ClinicalTrials.gov (www.clinicaltrials.gov); searched 30 March 2017 and the WHO International Clinical Trials Registry Platform (ICTRP) (www.who.int/ictrp/search/en); searched 30 March 2017. We did not use any date or language restrictions in the electronic searches for trials.We checked the reference lists of identified trials to search for further potentially relevant studies. RCTs comparing topical NSAIDs to placebo or any alternative analgesic interventions in adults with traumatic corneal abrasions. Two review authors independently performed data extraction and assessed risks of bias in the included studies. We rated the certainty of the evidence using GRADE. We included nine studies that met the inclusion criteria, reporting data on 637 participants.The studies took place in the UK, USA, Israel, Italy

Randomized controlled trials in dentistry: common pitfalls and how to avoid them.

PubMed

Fleming, Padhraig S; Lynch, Christopher D; Pandis, Nikolaos

2014-08-01

Clinical trials are used to appraise the effectiveness of clinical interventions throughout medicine and dentistry. Randomized controlled trials (RCTs) are established as the optimal primary design and are published with increasing frequency within the biomedical sciences, including dentistry. This review outlines common pitfalls associated with the conduct of randomized controlled trials in dentistry. Common failings in RCT design leading to various types of bias including selection, performance, detection and attrition bias are discussed in this review. Moreover, methods of minimizing and eliminating bias are presented to ensure that maximal benefit is derived from RCTs within dentistry. Well-designed RCTs have both upstream and downstream uses acting as a template for development and populating systematic reviews to permit more precise estimates of treatment efficacy and effectiveness. However, there is increasing awareness of waste in clinical research, whereby resource-intensive studies fail to provide a commensurate level of scientific evidence. Waste may stem either from inappropriate design or from inadequate reporting of RCTs; the importance of robust conduct of RCTs within dentistry is clear. Optimal reporting of randomized controlled trials within dentistry is necessary to ensure that trials are reliable and valid. Common shortcomings leading to important forms or bias are discussed and approaches to minimizing these issues are outlined. Copyright © 2014 Elsevier Ltd. All rights reserved.

Abrasive wear of resin composites as related to finishing and polishing procedures.

PubMed

Turssi, Cecilia P; Ferracane, Jack L; Serra, Mônica C

2005-07-01

Finishing and polishing procedures may cause topographical changes and introduce subsurface microcracks in dental composite restoratives. Since both of these effects may contribute toward the kinetics of wear, the purpose of this study was to assess and correlate the wear and surface roughness of minifilled and nanofilled composites finished and polished by different methods. Specimens (n=10) made of a minifilled and a nanofilled composite were finished and polished with one of the four sequences: (1) tungsten carbide burs plus Al(2)O(3)-impregnated brush (CbBr) or (2) tungsten carbide burs plus diamond-impregnated cup (CbCp), (3) diamond burs plus brush (DmBr) or (4) diamond burs plus cup (DmCp). As a control, abrasive papers were used. After surface roughness had been quantified, three-body abrasion was simulated using the OHSU wear machine. The wear facets were then scanned to measure wear depth and post-testing roughness. All sets of data were subjected to ANOVA and Tukey's tests (alpha=0.05). Pearson's correlation test was applied to check for the existence of a relationship between pre-testing roughness and wear. Significantly smoother surfaces were attained with the sequences CbBr and CbCp, whereas DmCp yielded the roughest surface. Regardless of the finishing/polishing technique, the nanofilled composite exhibited the lowest pre-testing roughness and wear. There was no correlation between the surface roughness achieved after finishing/polishing procedures and wear (p=0.3899). Nano-sized materials may have improved abrasive wear resistance over minifilled composites. The absence of correlation between wear and surface roughness produced by different finishing/polishing methods suggests that the latter negligibly influences material loss due to three-body abrasion.

Nanotechnology in dentistry: Present and future

PubMed Central

Bhardwaj, Archana; Bhardwaj, Abhishek; Misuriya, Abhinav; Maroli, Sohani; Manjula, S; Singh, Arvind Kumar

2014-01-01

Nanotechnology is the manipulation of matter on the molecular and atomic levels. It has the potential to bring enormous changes into the fields of medicine and dentistry. A day may soon come when nanodentistry will succeed in maintaining near-perfect oral health through the aid of nanorobotics, nanomaterials and biotechnology. However, as with all developments, it may also pose a risk for misuse. Time, economical and technical resources, and human needs will determine the direction this revolutionizing development may take. This article reviews the current status and the potential clinical applications of nanotechnology, nanaomedicine and nanodentistry. How to cite the article: Bhardwaj A, Bhardwaj A, Misuriya A, Maroli S, Manjula S, Singh AK. Nanotechnology in dentistry: Present and future. J Int Oral Health 2013;6(1):121-6. PMID:24653616

Going green with eco-friendly dentistry.

PubMed

Avinash, Bhagyalakshmi; Avinash, B S; Shivalinga, B M; Jyothikiran, S; Padmini, M N

2013-07-01

Eco-friendly dentistry is currently transforming the medical and dental field to decrease its affect on our natural environment and reduce the amount of waste being produced. Eco-friendly dentistry uses a sustainable approach to encourage dentists to implement new strategies to try and reduce the energy being consumed and the large amount of waste being produced by the industry. Many reasonable, practical and easy alternatives do exist which would reduce the environmental footprint of a dental office were it to follow the 'green' recommendations. Dentist should take a leading role in the society by implementing 'green' initiatives to lessen their impact on the environment. This article provides a series of 'green' recommendations that dentists around the world can implement to become a leading Stewards of the environment.

Environmental Assessment (EA): Proposed Aircraft Power Systems Repair Transformation Facility, Hill Air Force Base, Utah

DTIC Science & Technology

2007-05-16

and silicon carbide; spent elastic abrasive media; rags and wipes from the NDI process ; and unused scraps of TIG welding wire. Dust from the thermal...used, which would not be expected to produce regulated air emissions. For this process , no air quality permit updates are anticipated. • Welding ...The electron beam welding equipment would not be expected to produce regulated air emissions. The tungsten inert gas ( TIG ) welding equipment would

Study on Personality Types of Dentists in different Disciplines of Dentistry.

PubMed

Al-Dlaigan, Yousef H; Alahmari, Albatool S; Almubarak, Sara H; Alateeq, Sahar A; Anil, Sukumaran

2017-07-01

The purpose of this study was to determine the most common personality type among dentists in seven selected clinical dentistry specialties using the Myers-Briggs Type Indicator (MBTI) and to compare between these different types of personalities. A survey containing the MBTI and demographic and practice questions was used to assess the personality styles of 243 dental specialists in Riyadh, Saudi Arabia. The survey results were analyzed using descriptive statistics. The results of the MBTI for 243 specialist dentists revealed, generally, a higher percentage of scoring for introversion (I) with an average of 65% than extroversion (E). The study identified 10 common personality types among these specialists: ISTJ, ISFJ, INFJ, ISTP, INFP, INTP, ENFP, ENTP, ENFJ, and ENTJ (extraversion-introversion (E-I), sensing-intuition (S-N), thinking-feeling (T-F), and judging-perception (J-P)). The dominant personality type in all seven clinical specialties in dentistry was ISTJ, with an average of 54%. The personality types showed variation among the seven clinical dentistry specialties. However, among these seven clinician's specialties in dentistry, more than 50% of the individuals shared one common type of personality (ISTJ). The identification of the personality type might help in their association with coworkers, students, and patients as well as knowing the individual preferences toward different specialties in dentistry.

Finally in Italy the School of Specialisation in Paediatric Dentistry!

PubMed

Marzo, G

2017-06-01

After over two decades of discussions, promises and indecisions, the year 2016 marked the birth of the School of Specialisation in Paediatric Dentistry, which is now a reality. The importance of dental post-graduate specialisation schools has been debated since the Degree Course in Dentistry was established. Previously, in Italy only two dental branches - Oral Surgery and Orthodontics - had obtained the recognition that a School of Specialisation entails. Today, with specific training and the newly- established hyper-specialisation in Paediatric Dentistry, the future of the profession is brighter than ever. This will allow dental professionals to provide the best cure to our young patients but it especially marks and recognises the importance of prevention in general. Having established a Specialty School in Paediatric Dentistry is also important to keep the pace with the other European countries where this postgraduate course has been already offered for many years. In my opinion, training professionals with a solid specialisation based both on cultural insights and hands-on clinical activities translates into the possibility of making true prevention. The ultimate goal of paediatric dentists, as well as paediatricians, is certainly to treat young patients but also and above all to accompany them toward an adulthood possibly free of pathologies. With an eye to a future where Paediatric Dentistry will be at the core of dental and orthodontic prevention, I wish great success to all the many specialisation schools established within the Italian Universities.

The changing role of specialist care in NHS dentistry.

PubMed

Seward, M

1998-07-11

Specialisation and Specialist Training in Dentistry in the UK have been central issues for debate in the last few years. The profession has emerged stronger in understanding the respective roles of the generalist who should remain free to practise across the whole spectrum of dentistry and the specialist who can work in primary and secondary care. The overriding principle is that the patient remains the true beneficiary of a specialised service within the NHS.

Abrasion resistance of direct and indirect resins as a function of a sealant veneer.

PubMed

Ferraz Caneppele, Taciana Marco; Rocha, Daniel Maranha; Màximo Araujo, Maria Amelia; Valera, Màrcia Carneiro; Salazar Marocho, Susana MarIa

2014-01-01

Abrasive wear is one of the most common type of wear that not only affect teeth, as also dental restorations. Thus to investigate one of the etiological factors as tooth brushing procedure is clinical relevant in order to select the best material combination that may prevent damage of resin dental restoration's abrasion. This study evaluated the influence of tooth brushing on mass loss and surface roughness of direct Venus (Vs) and indirect Signum (Sg) resin composites, with and without a surface sealant, Fortify (F). Twenty-four specimens were prepared with each resin composite, using their proprietary curing units, according to manufacturer's instructions. All the specimens were polished and ultrasonically cleaned in distilled water for 5 minutes. Half of the specimens of each resin (n = 12) were covered with F (Vs F and Sg F ), except for the control (C) specimens (Vs C and Sg C ), which were not sealed. Mass loss (ML) as well as surface roughness (Ra ) was measured for all the specimens. Then, the specimens were subjected to toothbrush-dentifrice abrasion, using a testing machine for 67.000 brushing strokes, in an abrasive slurry. After brushing simulation, the specimens were removed from the holder, rinsed thoroughly and blot dried with soft absorbent paper. The abrasion of the material was quantitatively determined with final measurements of ML and surface roughness, using the method described above. ML data were analyzed by two-way analysis of variance (ANOVA) and the analysis indicated that resin composites were not statistically different; however, the specimens sealed with F showed higher ML. Ra mean values of the groups Vs F and Sg F significantly increased. Tooth brushing affects mainly the roughness of the direct and indirect resin composites veneered with a sealant.

[A survey on knowledge, attitude and practice related to evidence-based dentistry among dental students].

PubMed

Chang, Zhong-Fu; Zhu, Ce; Tao, Dan-Ying; Feng, Xi-Ping; Lu, Hai-Xia

2017-04-01

To investigate the knowledge, attitude and practice related to evidence-based dentistry among dental students, and to provide a reference for targeted evidence-based dentistry teaching and practice evidence-based dentistry in dental students. Dental students who attended the internship in Shanghai Ninth People's Hospital and Pudong People's Hospital were invited to attend this survey. Information on knowledge, attitude and practices related evidence-based dentistry was collected through questionnaires. SPSS 21.0 software package was used for data analysis. A total of 62 dental students attended this survey. Evidence-based dentistry related knowledge and attitude scores were 5.5±1.9 and 5.1±1.0, respectively. Over three quarters of students took courses on evidence-based medicine, while around half of students (56.5%) self-reported that they knew little about evidence-based medicine. 70.5% students practiced evidence-based dentistry less than once in the process of clinical decision making per week. The majority of students (80.3%) used MEDLINE or other databases to search for practice-related literature less than once per week. 63.9% students used practice guideline. The top three barriers to practice evidence-based dentistry were lack of information resources, insufficient time and lack of search skills. Evidence-based dentistry related knowledge and practice among dental students is deficient, whereas they hold positive attitude on practice. The top three barriers to practice evidence-based dentistry are lack of information resources, insufficient time and lack of search skills.

A psychosocial approach to dentistry for the underserved: incorporating theory into practice.

PubMed

Flaer, Paul J; Younis, Mustafa Z; Benjamin, Paul L; Al Hajeri, Maha

2010-01-01

Dentistry for the underserved is more than an egalitarian social issue--it is a key factor in the health and social progress of our nation. The first signs or manifestations of several diseases such as varicella (i.e., chicken pox and shingles), STDs, and influenza become apparent in the oral cavity. The value of access to quality dentistry is an immeasurable factor in maintaining general medical health of people and fulfilling their psychosocial needs of pain reduction and enhanced cosmetics. In the United States, for the most part, only the middle and upper classes receive non-extraction, restorative, and prosthetic dentistry that is economically within their ability to pay. In addition, uninsured and poverty-level individuals often must face overwhelming long waiting lists, unnecessary referrals, lack of choice, and bureaucratic hurdles when seeking primary dental care. Therefore, it seems pertinent to put forth the question: What are the critical values and beliefs of psychosocial theory that can underscore the practice of dentistry for underserved populations in the United States? The widely employed public health theory, the health belief model (HBM), is applied to evaluate psychosocial factors in dental care for the underserved. The HBM is used to predict and explain behavioral changes in dental health and associated belief patterns. The HBM as applied to dentistry for the underserved predicts self-perceptions of susceptibility and seriousness of dental disease, health status, cues to action, and self-efficacy. Furthermore, patients can make judgments about benefits, costs, and risks of dental treatment. A theoretical approach to dentistry employing the HBM, mediated by values and culture, can provide significant insights into patient thinking, beliefs, and perceptions. These insights can mediate access to and use of primary care dental services by underserved populations. Evidence-based practice (i.e., based on research using the scientific method) has been

Preventive Dentistry and Oral Hygiene.

PubMed

Clavagnier, Isabelle

2015-05-01

The biggest oral health campaign in the United Kingdom is called "National Smile Month" and it starts in May. For this occasion, the occupational medicine team of Kensington Hospital is holding special events highlighting preventive dentistry and oral hygiene. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Dentistry and Dental Hygiene Handbook.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Office of the Professions.

The handbook contains laws, rules, and regulations of the New York State Education Department that govern dentistry and dental hygiene practice in the state. It describes licensure requirements and includes complete application forms and instructions for obtaining license and first registration as a dentist and dental hygienist. Applicants are…

Recent advances of ultrasound imaging in dentistry--a review of the literature.

PubMed

Marotti, Juliana; Heger, Stefan; Tinschert, Joachim; Tortamano, Pedro; Chuembou, Fabrice; Radermacher, Klaus; Wolfart, Stefan

2013-06-01

Ultrasonography as an imaging modality in dentistry has been extensively explored in recent years due to several advantages that diagnostic ultrasound provides. It is a non-invasive, inexpensive, painless method and unlike X-ray, it does not cause harmful ionizing radiation. Ultrasound has a promising future as a diagnostic imaging tool in all specialties in dentistry, for both hard and soft tissue detection. The aim of this review is to provide the scientific community and clinicians with an overview of the most recent advances of ultrasound imaging in dentistry. The use of ultrasound is described and discussed in the fields of dental scanning, caries detection, dental fractures, soft tissue and periapical lesions, maxillofacial fractures, periodontal bony defects, gingival and muscle thickness, temporomandibular disorders, and implant dentistry. Copyright © 2013 Elsevier Inc. All rights reserved.

Evolution and diagnostic utility of aeolian rat-tails: A new type of abrasion feature on Earth and Mars

NASA Astrophysics Data System (ADS)

Favaro, Elena A.; Hugenholtz, Christopher H.; Barchyn, Thomas E.

2017-10-01

Aeolian rat-tails (ARTs) are a previously undocumented, regionally-ubiquitous aeolian abrasion feature observed on matrix-supported ignimbrite surfaces in the Puna Plateau of Northwest Argentina. ARTs consist of an abrasion-resistant lithic clast projecting above the surface with a lee tail or 'keel' in the more erodible matrix. Size is controlled by the dimensions of the windward lithic clast, ranging from centimetre to meter scale; spatial density varies with clast content, which may reflect variations in ignimbrite facies. Field observations suggest ARTs follow a definable evolutionary sequence. First, an abrasion-resistant lithic clast contained within the ignimbrite is exposed to abrasion at the surface. Impacts from abrading particles erode the softer ignimbrite matrix adjacent to the clast. The clast shelters the leeward surface under a unimodal abrasion direction, creating a tail that tapers downwind and elongates as the clast emerges. Clasts become dislodged from the matrix as the surrounding surface erodes, ultimately destroying the feature if the clast is small enough to be mobilized directly by wind or impacting particles. This evolutionary sequence explains the morphology of ARTs and the presence of loose clasts on the ignimbrite surface, which contributes to the development of other landforms in the region, such as periodic bedrock ridges, yardangs, and megaripples. Satellite and rover images suggest similar features also exist on Mars. Because the formation and preservation of ARTs is contingent on unimodal abrasion direction, their orientation can be used as an indicator of long-term aeolian sediment transport direction.

Dentistry as a free market in the context of leading policymaking.

PubMed

Franzon, Bengt; Englander, Magnus; Axtelius, Björn; Klinge, Björn

2018-12-01

The purpose of this study was to disclose the psychological meaning structure of dentistry as a free market within the context of leading Swedish policymaking. Following the criteria for the descriptive phenomenological psychological method data was collected from leading policy makers about the experiential aspects of dentistry as a free market within the context of a welfare state. The analysis showed that dentistry as a free market was experienced as a complex business relationship between buyers and sellers that transcended the traditional dentist and patient roles. The lived experience of the proposed business transaction was based on two inherently conflicting views: the belief in the individual's ability to make a free choice versus the understanding that all individuals in a society do not have the ability or the means necessary to make a free choice. Dentistry as a free market within a welfare state, such as Sweden, can thus be seen as a persistent attempt to hold on to a compromise between two very distinctive political ideologies.

Theoretical study on removal rate and surface roughness in grinding a RB-SiC mirror with a fixed abrasive.

PubMed

Wang, Xu; Zhang, Xuejun

2009-02-10

This paper is based on a microinteraction principle of fabricating a RB-SiC material with a fixed abrasive. The influence of the depth formed on a RB-SiC workpiece by a diamond abrasive on the material removal rate and the surface roughness of an optical component are quantitatively discussed. A mathematical model of the material removal rate and the simulation results of the surface roughness are achieved. In spite of some small difference between the experimental results and the theoretical anticipation, which is predictable, the actual removal rate matches the theoretical prediction very well. The fixed abrasive technology's characteristic of easy prediction is of great significance in the optical fabrication industry, so this brand-new fixed abrasive technology has wide application possibilities.

Interfacing superhydrophobic silica nanoparticle films with graphene and thermoplastic polyurethane for wear/abrasion resistance.

PubMed

Naderizadeh, Sara; Athanassiou, Athanassia; Bayer, Ilker S

2018-06-01

Nanoparticle films are one of the most suitable platforms for obtaining sub-micrometer and nanometer dual-scale surface texture required for liquid repellency. The assembly of superhydrophobic nanoparticles into conformal and strongly adherent films having abrasion-induced wear resistance still poses a significant challenge. Various techniques have been developed over the years to render nanoparticle films with good liquid repellent properties and transparency. However, forming abrasion resistant superhydrophobic nanoparticle films on hard surfaces is challenging. One possibility is to partially embed or weld nanoparticles in thin thermoplastic primers applied over metals. Hexamethyldisilazane-functionalized fumed silica nanoparticle films spray deposited on aluminum surfaces were rendered abrasion resistant by thermally welding them into thermoplastic polyurethane (TPU) primer applied a priori over aluminum. Different solvents, nanoparticle concentrations and annealing temperatures were studied to optimize nanoparticle film morphology and hydrophobicity. Thermal annealing at 150 °C enhanced stability and wear resistance of nanoparticle films. A thin thermal interface layer of graphene nanoplatelets (GnPs) between the primer and the nanoparticle film significantly improved superhydrophobic wear resistance after annealing. As such, superhydrophobic nanocomposite films with the GnPs thermal interface layer displayed superior abrasion-induced wear resistance under 20 kPa compared to films having no GnPs-based thermal interface. Copyright © 2018 Elsevier Inc. All rights reserved.

Abrasive slurry composition for machining boron carbide

DOEpatents

Duran, Edward L.

1985-01-01

An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

Abrasive slurry composition for machining boron carbide

DOEpatents

Duran, E.L.

1984-11-29

An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

NK cells are necessary for recovery of corneal CD11c+ dendritic cells after epithelial abrasion injury

USDA-ARS?s Scientific Manuscript database

Mechanisms controlling CD11c(+) MHCII(+) DCs during corneal epithelial wound healing were investigated in a murine model of corneal abrasion. Selective depletion of NKp46(+) CD3- NK cells that normally migrate into the cornea after epithelial abrasion resulted in >85% reduction of the epithelial CD1...

The Future of Clinical Dentistry.

ERIC Educational Resources Information Center

Slavkin, Harold C.

1998-01-01

Discussion of the future of clinical dentistry looks at a variety of influences, including historical development factors; demographic trends; the role of the Human Genome Project in the development of scientific knowledge; a paradigm shift in approaches to oral infection and systemic disease; advancing technology; and reforms resulting from these…

77 FR 9664 - Funds for Leadership Training in Pediatric Dentistry's Current Grantees; One-Year Extension

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-17

... Leadership Training in Pediatric Dentistry's Current Grantees; One-Year Extension AGENCY: Health Resources... Funds for Leadership Training in Pediatric Dentistry's (T17) Current Grantees. SUMMARY: The Health... for the Leadership Training in Pediatric Dentistry awards to Columbia University, The Regents of the...

Dentistry students' perceptions of learning management systems.

PubMed

Handal, B; Groenlund, C; Gerzina, T

2010-02-01

This paper reports an exploratory survey study about students' perceptions of learning management systems (LMS) at the Faculty of Dentistry, University of Sydney. Two hundred and fifty-four students enrolled in the Bachelor of Dentistry and the Bachelor of Oral Health programmes participated in an online survey aimed at exploring their beliefs and attitudes as well as their preferences for eLearning tools. Results indicated a strong preference of students for using LMSs as resource repositories rather than for higher-order learning activities such as online discussion forums. This finding holds importance for consideration of the development of the educational resources modalities that support development of essential graduate attributes such as information literacy and collaborative learning.

Application of Calcium Phosphate Materials in Dentistry

PubMed Central

Al-Sanabani, Jabr S.; Al-Sanabani, Fadhel A.

2013-01-01

Calcium phosphate materials are similar to bone in composition and in having bioactive and osteoconductive properties. Calcium phosphate materials in different forms, as cements, composites, and coatings, are used in many medical and dental applications. This paper reviews the applications of these materials in dentistry. It presents a brief history, dental applications, and methods for improving their mechanical properties. Notable research is highlighted regarding (1) application of calcium phosphate into various fields in dentistry; (2) improving mechanical properties of calcium phosphate; (3) biomimetic process and functionally graded materials. This paper deals with most common types of the calcium phosphate materials such as hydroxyapatite and tricalcium phosphate which are currently used in dental and medical fields. PMID:23878541

Transcutaneous electric nerve stimulation (TENS) in dentistry- A review.

PubMed

Kasat, Vikrant; Gupta, Aditi; Ladda, Ruchi; Kathariya, Mitesh; Saluja, Harish; Farooqui, Anjum-Ara

2014-12-01

Transcutaneous electric nerve stimulation (TENS) is a non-pharmacological method which is widely used by medical and paramedical professionals for the management of acute and chronic pain in a variety of conditions. Similarly, it can be utilized for the management of pain during various dental procedures as well as pain due to various conditions affecting maxillofacial region. This review aims to provide an insight into clinical research evidence available for the analgesic and non analgesic uses of TENS in pediatric as well as adult patients related to the field of dentistry. Also, an attempt is made to briefly discuss history of therapeutic electricity, mechanism of action of TENS, components of TENs equipment, types, techniques of administration, advantages and contradictions of TENS. With this we hope to raise awareness among dental fraternity regarding its dental applications thereby increasing its use in dentistry. Key words:Dentistry, pain, TENS.

Transcutaneous electric nerve stimulation (TENS) in dentistry- A review

PubMed Central

Gupta, Aditi; Ladda, Ruchi; Kathariya, Mitesh; Saluja, Harish; Farooqui, Anjum-Ara

2014-01-01

Transcutaneous electric nerve stimulation (TENS) is a non-pharmacological method which is widely used by medical and paramedical professionals for the management of acute and chronic pain in a variety of conditions. Similarly, it can be utilized for the management of pain during various dental procedures as well as pain due to various conditions affecting maxillofacial region. This review aims to provide an insight into clinical research evidence available for the analgesic and non analgesic uses of TENS in pediatric as well as adult patients related to the field of dentistry. Also, an attempt is made to briefly discuss history of therapeutic electricity, mechanism of action of TENS, components of TENs equipment, types, techniques of administration, advantages and contradictions of TENS. With this we hope to raise awareness among dental fraternity regarding its dental applications thereby increasing its use in dentistry. Key words:Dentistry, pain, TENS. PMID:25674327

Abrasive wear behavior of heat-treated ABC-silicon carbide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xiao Feng; Lee, Gun Y.; Chen, Da

2002-06-17

Hot-pressed silicon carbide, containing aluminum, boron, and carbon additives (ABC-SiC), was subjected to three-body and two-body wear testing using diamond abrasives over a range of sizes. In general, the wear resistance of ABC-SiC, with suitable heat treatment, was superior to that of commercial SiC.

YouTube, dentistry, and dental education.

PubMed

Knösel, Michael; Jung, Klaus; Bleckmann, Annalen

2011-12-01

The objective of this study was to systematically assess the informational value, intention, source, and bias of videos related to dentistry available on the video-sharing Internet platform YouTube. YouTube (www.youtube.com) was searched for videos related to dentistry, using the system-generated sorts "by relevance" and "most viewed" and two categories (All and Education). Each of the first thirty results was rated by two assessors filling out a questionnaire for each (total: 120). The data were subjected to statistical analysis using Cohen's kappa, Pearson's correlation coefficient tau, Mann-Whitney U-tests, and a nonparametric three-way ANOVA, including an analysis of the interaction between the sorting and category effect, with an α-level of 5 percent. The scan produced 279,000 results in the category All and 5,050 in the category Education. The analysis revealed a wide variety of information about dentistry available on YouTube. The purpose of these videos includes entertainment, advertising, and education. The videos classified under Education have a higher degree of usefulness and informational value for laypersons, dental students, and dental professionals than those found in a broader search category. YouTube and similar social media websites offer new educational possibilities that are currently both underdeveloped and underestimated in terms of their potential value. Dentists and dental educators should also recognize the importance of these websites in shaping public opinion about their profession.

The application of CAD / CAM technology in Dentistry

NASA Astrophysics Data System (ADS)

Susic, I.; Travar, M.; Susic, M.

2017-05-01

Information and communication technologies have found their application in the healthcare sector, including the frameworks of modern dentistry. CAD / CAM application in dentistry is the process by which is attained finished dental restoration through fine milling process of ready ceramic blocks. CAD / CAM is an acronym of english words Computer-Aided-Design (CAD) / Computer-Aided-Manufacture (CAM), respectively dental computer aided design and computer aided manufacture of inlays, onlays, crowns and bridges. CAD / CAM technology essentially allows you to create a two-dimensional and three-dimensional models and their materialization by numerical controlled machines. In order to operate more efficiently, reduce costs, increase user/patient satisfaction and ultimately achieve profits, many dental offices in the world have their attention focused on implementation of modern IT solutions in everyday practice. In addition to the specialized clinic management software, inventory control, etc., or hardware such as the use of lasers in cosmetic dentistry or intraoral scanning, recently the importance is given to the application of CAD / CAM technology in the field of prosthetic. After the removal of pathologically altered tooth structure, it is necessary to achieve restoration that will be most similar to the anatomy of a natural tooth. Applying CAD / CAM technology on applicable ceramic blocks it can be obtained very quick, but also very accurate restoration, in the forms of inlays, onlays, bridges and crowns. The paper presents the advantages of using this technology as well as satisfaction of the patients and dentists by using systems as: Cercon, Celay, Cerec, Lava, Everest, which represent imperative of modern dentistry in creating fixed dental restorations.

Investigation of The Omaha System for dentistry.

PubMed

Jurkovich, M W; Ophaug, M; Salberg, S; Monsen, K

2014-01-01

Today, dentists and hygienists have inadequate tools to identify contributing factors to dental disease, diagnosis of disease or to document outcomes in a standardized and machine readable format. Increasing demand to find the most effective care methodologies make the development of further terminologies for dentistry more urgent. Preventive care is the focus of early efforts to define best practices. We reviewed one possibility with a history of public health documentation that might assist in these early efforts at identifying best practices. This paper examines, through a survey of dentists, the Omaha System Problem Classification Scheme. The survey requested that dentists rate the usefulness of knowing about specific signs and symptoms for each of the 42 problems within the Problem list of the Omaha System. Using a weighted scoring system, 22 of the 42 problems received over 50% of the possible maximum score and 30 of the 42 problems received at least 25% of the possible points. These findings suggests that further evaluation of The Omaha System, may be useful to dentistry. At a minimum, the survey provides additional information about non-physiological problems, signs, and symptoms that may be appropriate for documentation purposes within an electronic health record (EHR) used in dentistry.

Dentistry--a show of hands, please!

PubMed

Rucker, Lance M

2007-01-01

Dentists have historically derived a distinctive part of their identity from the role of hand skills in practice. Dentistry is a surgical discipline, requiring a basic competency to perform what has been diagnosed and planned as being in the patients' best interests. Dental education has introduced magnification and computer-assisted technique instruction as the proportion of clock-hours devoted to laboratory practice has decreased. The threats posed by traumatic hand injury to practitioners are unknown, but may be small. By contrast, the strain of repetitive motion and injuries caused by postural problems are reported to be widespread in the profession and is generally accepted as characteristic and unavoidable. Ergonomic approaches to alleviating work strain have not been broadly embraced. As dentistry incorporates more biological alternatives and automated technology, the role of hands in practice may change.

Optical tools for high-throughput screening of abrasion resistance of combinatorial libraries of organic coatings

NASA Astrophysics Data System (ADS)

Potyrailo, Radislav A.; Chisholm, Bret J.; Olson, Daniel R.; Brennan, Michael J.; Molaison, Chris A.

2002-02-01

Design, validation, and implementation of an optical spectroscopic system for high-throughput analysis of combinatorially developed protective organic coatings are reported. Our approach replaces labor-intensive coating evaluation steps with an automated system that rapidly analyzes 8x6 arrays of coating elements that are deposited on a plastic substrate. Each coating element of the library is 10 mm in diameter and 2 to 5 micrometers thick. Performance of coatings is evaluated with respect to their resistance to wear abrasion because this parameter is one of the primary considerations in end-use applications. Upon testing, the organic coatings undergo changes that are impossible to quantitatively predict using existing knowledge. Coatings are abraded using industry-accepted abrasion test methods at single-or multiple-abrasion conditions, followed by high- throughput analysis of abrasion-induced light scatter. The developed automated system is optimized for the analysis of diffusively scattered light that corresponds to 0 to 30% haze. System precision of 0.1 to 2.5% relative standard deviation provides capability for the reliable ranking of coatings performance. While the system was implemented for high-throughput screening of combinatorially developed organic protective coatings for automotive applications, it can be applied to a variety of other applications where materials ranking can be achieved using optical spectroscopic tools.

Abrasion resistance of muscovite in aeolian and subaqueous transport experiments

NASA Astrophysics Data System (ADS)

Anderson, Calvin J.; Struble, Alexander; Whitmore, John H.

2017-02-01

Complementary aeolian and subaqueous transport experiments showed a trend in muscovite abrasion that may be useful for identifying ancient sandstones as aeolian or subaqueous in origin. We found that our experimental aeolian processes pulverized the micas quickly, while our subaqueous processes did not. In a pair of abrasion resistance experiments conducted with micaceous quartz sand, it was found that large muscovite grains were (1) reduced by aeolian processes to less than 500 μm in just 4 days, and (2) preserved by subaqueous processes to 610 ± 90 μm even after 356 days. At 20 days of aeolian transport no loose micas could be found even under the microscope, but after a year of subaqueous transport loose muscovite grains could still be seen with the naked eye. Thus, the occurrence and character of micas in a sandstone, particularly muscovite, may be helpful in determining the ancient depositional process.

Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

NASA Technical Reports Server (NTRS)

Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

2011-01-01

The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width as currently defined by the ASTM G 171 Standard. The ZOI has been found to be at least twice the size of a standard width measurement, in some cases considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for detailed analysis. Documenting additional changes to various surface roughness parameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Data are presented to show that different combinations of scratch tips and abraded materials can actually yield the same scratch width, but result in different volume displacement or removal measurements and therefore, the ZOI method is more discriminating than the ASTM method scratch width. Furthermore, by investigating the use of custom scratch tips for our specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized manner, and not just by scratch width alone, is reinforced. This benefit is made apparent when a tip creates an intricate contour having multiple peaks and valleys within a single scratch. This work lays the foundation for updating scratch measurement standards to improve modeling and characterization of three-body abrasion test results.

Paediatric conscious sedation: views and experience of specialists in paediatric dentistry.

PubMed

Woolley, S M; Hingston, E J; Shah, J; Chadwick, B L

2009-09-26

The objectives were three-fold: to investigate the level of conscious sedation training received prior to and during specialist training in paediatric dentistry; to establish the use of conscious sedation during and following specialisation; and to determine the attitudes of specialists in paediatric dentistry to conscious sedation. A self-administered postal questionnaire was sent to all specialists in paediatric dentistry registered with the General Dental Council in January 2008. Non-responders were contacted again after a four-week period. A response rate of 60% was achieved. Of the 122 respondents, 67 (55%) had received sedation training as an undergraduate; 89 (75%) had been trained during specialisation. All respondents performed dental treatment under sedation as a trainee and the majority used nitrous oxide inhalation sedation (NOIS). Over 90% of respondents felt that NOIS should be available to all children, both in appropriate primary care settings and in hospitals. One hundred and twenty-one (99%) respondents thought that all trainees in paediatric dentistry should have sedation training. The most popular form of sedation amongst specialists in paediatric dentistry was NOIS. However, some of the respondents felt that children should have access to other forms of sedation in both the primary care and hospital settings. Additional research on other forms of sedation is required to evaluate their effectiveness and safety.

Need for geriatric dentistry training programs in Iran.

PubMed

Mir, Arash Poorsattar Bejeh

2013-01-01

A shifting pattern from communicable diseases to the chronic noncommunicable diseases and increased life expectancy are being sensed throughout the world. Aged populations with multiple chronic diseases come up with their unique needs and require specific attention to be challenged by the health systems. Neglected orodental facts among the elders and the dearth of specific designated undergraduate and postgraduate courses of geriatric dentistry in Iran inevitably adversely affect the delivery of appropriate dental care service to elders by untrained dentists. In this article, a proposal for academic geriatric dentistry courses in Iran is introduced and highlighted with regards to elders' special needs.

The change in retentive force of magnetic attachment by abrasion.

PubMed

Huang, Yuanjin; Tawada, Yasuyuki; Hata, Yoshiaki; Watanabe, Fumihiko

2008-07-01

Magnets are frequently applied to removable dentures as retentive attachments. A magnet-retained removable overdenture might be slightly shifted from side to side by eccentric movement in the mouth, and the surface of magnetic attachment may be worn as a result. However, the relationship between the retentive force of magnetic attachment and its surface abrasion has not been reported. The purpose of this research is to investigate this relationship. Ten Mgfit DX 400 magnetic attachments for natural tooth roots were used for this experiment. The magnetic attachments were embedded in autopolymerizing acrylic resin, and ten pairs of specimens were fabricated. A 5-mm repeated gliding motion was applied on each pair of specimens until 30 000, 50 000, or 90 000 cycles had been achieved. The abrasion machine was under 5 kg loading, and the slide speed was 60 times/min. The retentive force of magnetic attachment was measured with a tension gauge at (1) before gliding; (2) after 30 000 gliding cycles; (3)after 50 000 gliding cycles; or (4) after 90 000 gliding cycles. The average change of retentive force of ten magnetic attachments after 30 000, 50 000, and 90 000 gliding cycles was 0.016 N, 0.003 N, and -0.008 N, respectively. The change was statistically analyzed using a paired-sample t test, which showed that the number of gliding cycles did not affect the retentive force of magnetic attachment significantly. The surface of magnetic attachment after gliding was observed by a microscope, and the abrasion of this attachment surface is clearly seen.

Micro-scale abrasive wear behavior of medical implant material Ti-25Nb-3Mo-3Zr-2Sn alloy on various friction pairs.

PubMed

Wang, Zhenguo; Huang, Weijiu; Ma, Yanlong

2014-09-01

The micro-scale abrasion behaviors of surgical implant materials have often been reported in the literature. However, little work has been reported on the micro-scale abrasive wear behavior of Ti-25Nb-3Mo-3Zr-2Sn (TLM) titanium alloy in simulated body fluids, especially with respect to friction pairs. Therefore, a TE66 Micro-Scale Abrasion Tester was used to study the micro-scale abrasive wear behavior of the TLM alloy. This study covers the friction coefficient and wear loss of the TLM alloy induced by various friction pairs. Different friction pairs comprised of ZrO2, Si3N4 and Al2O3 ceramic balls with 25.4mm diameters were employed. The micro-scale abrasive wear mechanisms and synergistic effect between corrosion and micro-abrasion of the TLM alloy were investigated under various wear-corrosion conditions employing an abrasive, comprised of SiC (3.5 ± 0.5 μm), in two test solutions, Hanks' solution and distilled water. Before the test, the specimens were heat treated at 760°C/1.0/AC+550°C/6.0/AC. It was discovered that the friction coefficient values of the TLM alloy are larger than those in distilled water regardless of friction pairs used, because of the corrosive Hanks' solution. It was also found that the value of the friction coefficient was volatile at the beginning of wear testing, and it became more stable with further experiments. Because the ceramic balls have different properties, especially with respect to the Vickers hardness (Hv), the wear loss of the TLM alloy increased as the ball hardness increased. In addition, the wear loss of the TLM alloy in Hanks' solution was greater than that in distilled water, and this was due to the synergistic effect of micro-abrasion and corrosion, and this micro-abrasion played a leading role in the wear process. The micro-scale abrasive wear mechanism of the TLM alloy gradually changed from two-body to mixed abrasion and then to three-body abrasion as the Vickers hardness of the balls increased. Copyright �

Explosibility and Ignitability of Plastic Abrasive Media.

DTIC Science & Technology

1987-06-01

Polyplus Is an alpha cellulose filled urea formaldehyde with a hardness or 3.5. Type III is a urea melamine formaldehyde with a hardness of 4. A fourth...is a thermoplastic acrylic media and the Kopper’s media are thermoset formaldehydes . o The greatest potential for dust explosions is in the baghouss...type or plastio media trom E. I. Du Pont de Nemours and Company was also tested. This Type L Solidstrip plastic stripping abrasive is an acrylic resin

Restorative dentistry for children.

PubMed

Donly, Kevin J

2013-01-01

This article discusses contemporary pediatric restorative dentistry. Indications and contraindications for the choice of different restorative materials in different clinical situations, including the risk assessment of the patient, are presented. The specific use of glass ionomer cement or resin-modified glass ionomer cement, resin-based composite, and stainless steel crowns is discussed so that preparation design and restoration placement is understood. Copyright © 2013 Elsevier Inc. All rights reserved.

Rock Abrasion Tool Exhibits the Deep Red Pigment of Mars

NASA Image and Video Library

2006-07-21

This image shows the round, metallic working end of the rock abrasion tool at the end of a metallic cylinder. The flat grinding face, attached brush, and much of the smooth, metallic exterior of cylinder are covered with a deep reddish-brown layer of dust

Nanotechnology and dentistry

PubMed Central

Ozak, Sule Tugba; Ozkan, Pelin

2013-01-01

Nanotechnology deals with the physical, chemical, and biological properties of structures and their components at nanoscale dimensions. Nanotechnology is based on the concept of creating functional structures by controlling atoms and molecules on a one-by-one basis. The use of this technology will allow many developments in the health sciences as well as in materials science, bio-technology, electronic and computer technology, aviation, and space exploration. With developments in materials science and biotechnology, nanotechnology is especially anticipated to provide advances in dentistry and innovations in oral health-related diagnostic and therapeutic methods. PMID:23408486

Black triangle dilemma and its management in esthetic dentistry.

PubMed

Singh, Vijendra P; Uppoor, Ashita S; Nayak, Dilip G; Shah, Dipen

2013-05-01

In recent years, clinician and dentist's esthetic demand in dentistry have increased rapidly, driven by an enhanced awareness of beauty and esthetics. The ultimate goal in modern restorative dentistry is to achieve "white" and "pink" esthetics in esthetically important zones. "White esthetics" is the natural dentition or the restoration of dental hard tissues with suitable materials. "Pink esthetics" refers to the surrounding soft-tissues, which includes the interdental papilla and gingiva that can enhance or diminish the esthetic result. Reconstruction of the lost interdental papilla is one of the most challenging and least predictable problems. Restoration and maintenance of these tissues with adequate surgical and prosthetic techniques are a real challenge in modern esthetic dentistry. Treatment of marginal tissue recession, excessive gingival display, deficient ridges, ridge collapse, and esthetic defects around teeth and implants are some of the esthetic problems associated with the interdental papilla that have to be corrected in todays scenario which has been discussed in this review.

Cone beam computed tomography in paediatric dentistry: overview of recent literature.

PubMed

Aps, J K M

2013-06-01

The use of cone beam computed tomography (CBCT) in paediatric dentistry has been mentioned in numerous publications and case reports. The indications for the use of CBCT in paediatric dentistry, however, have not yet been properly addressed. On the other hand, the three basic principles of radiation protection (justification, limitation and optimisation) should suffice. A review of the current literature was used to assess the indications and contra-indications for the use of CBCT in paediatric dentistry. Paramount is the fact that CBCT generates a higher effective dose to the tissues than traditional dental radiographic exposures do. The effective radiation dose should not be underestimated, especially not in children, who are much more susceptible to stochastic biological effects. The thyroid gland in particular should be kept out of the primary beam as much as possible. As with any other radiographical technique, routine use of CBCT is not acceptable clinical practice. CBCT certainly has a place in paediatric dentistry, but its use must be justified on a patient case individual basis.

Dentistry as a free market in the context of leading policymaking

PubMed Central

Franzon, Bengt; Englander, Magnus; Axtelius, Björn

2018-01-01

ABSTRACT The purpose of this study was to disclose the psychological meaning structure of dentistry as a free market within the context of leading Swedish policymaking. Following the criteria for the descriptive phenomenological psychological method data was collected from leading policy makers about the experiential aspects of dentistry as a free market within the context of a welfare state. The analysis showed that dentistry as a free market was experienced as a complex business relationship between buyers and sellers that transcended the traditional dentist and patient roles. The lived experience of the proposed business transaction was based on two inherently conflicting views: the belief in the individual’s ability to make a free choice versus the understanding that all individuals in a society do not have the ability or the means necessary to make a free choice. Dentistry as a free market within a welfare state, such as Sweden, can thus be seen as a persistent attempt to hold on to a compromise between two very distinctive political ideologies. PMID:29912654

[Prevalence of dental diseases among Moscow students and need of dentistry].

PubMed

Makeeva, I M; Doroshina, V Iu; Protsenko, A S

2009-01-01

A clinical epidemiologic study was made among 432 Moscow students and as a part of it was found the high prevalence rate of pathologies of dentition and variety of nosologic forms. The most common cases were: caries, periodontal disease, deformity and anomalies of tooth position. These findings were necessary to estimate the need of all types of dentistry for Moscow students. It was specified that 43% of students were in need of filling and dental restoration, 35% were in need of crowns of tooth, 22% were in need of dental restoration by means of orthopedic constructions. Endodontic dentistry was necessary for 31% of students, surgical removal - for 8%, periodontal dentistry - for 37%.

Perceived competency towards preventive dentistry among dental graduates: the need for curriculum change.

PubMed

Arheiam, Arheiam; Bankia, Ibtesam; Ingafou, Mohamed

2015-01-01

A previous study has shown that dental practitioners in Benghazi believed that the less prevention-oriented education system is one of the barriers to applying preventive dentistry. To assess attitudes and perceived competence of the dental graduates in Benghazi towards prevention and early management of dental caries. A cross-sectional, questionnaire-based survey was conducted among internship students attending the Department of Community and Preventive Dentistry in Faculty of Dentistry, Benghazi, Libya. The participants were asked to provide demographic information, to respond to statements about their attitudes towards preventive dentistry, and to answer questions regarding their perceived competence in applying preventive dentistry procedures. Data from 108 Libyan dental graduates were analysed for this study, of which 64% of them were females and 42.1% of them passed their final year with grade: acceptable. The most acknowledged aspects of preventive dentistry were being useful and essential to the community (95.4 and 90.8%, respectively). The percentage of participants expressing a proficiency in providing oral hygiene instructions was the highest (95.4%). There were differences between study subgroups in their perceived competence of preventive dental practices by gender and academic performance (p≤0.05). This study highlighted that the currently implemented undergraduate education programme in Benghazi dental school does not provide dentists with the required attitude and skills to fulfil their role in providing preventive-oriented health services.

A Profilometry-Based Dentifrice Abrasion Method for V8 Brushing Machines Part II: Comparison of RDA-PE and Radiotracer RDA Measures.

PubMed

Schneiderman, Eva; Colón, Ellen; White, Donald J; St John, Samuel

2015-01-01

The purpose of this study was to compare the abrasivity of commercial dentifrices by two techniques: the conventional gold standard radiotracer-based Radioactive Dentin Abrasivity (RDA) method; and a newly validated technique based on V8 brushing that included a profilometry-based evaluation of dentin wear. This profilometry-based method is referred to as RDA-Profilometry Equivalent, or RDA-PE. A total of 36 dentifrices were sourced from four global dentifrice markets (Asia Pacific [including China], Europe, Latin America, and North America) and tested blindly using both the standard radiotracer (RDA) method and the new profilometry method (RDA-PE), taking care to follow specific details related to specimen preparation and treatment. Commercial dentifrices tested exhibited a wide range of abrasivity, with virtually all falling well under the industry accepted upper limit of 250; that is, 2.5 times the level of abrasion measured using an ISO 11609 abrasivity reference calcium pyrophosphate as the reference control. RDA and RDA-PE comparisons were linear across the entire range of abrasivity (r2 = 0.7102) and both measures exhibited similar reproducibility with replicate assessments. RDA-PE assessments were not just linearly correlated, but were also proportional to conventional RDA measures. The linearity and proportionality of the results of the current study support that both methods (RDA or RDA-PE) provide similar results and justify a rationale for making the upper abrasivity limit of 250 apply to both RDA and RDA-PE.

A quantitative estimation of the exhaust, abrasion and resuspension components of particulate traffic emissions using electron microscopy

NASA Astrophysics Data System (ADS)

Weinbruch, Stephan; Worringen, Annette; Ebert, Martin; Scheuvens, Dirk; Kandler, Konrad; Pfeffer, Ulrich; Bruckmann, Peter

2014-12-01

The contribution of the three traffic-related components exhaust, abrasion, and resuspension to kerbside and urban background PM10 and PM1 levels was quantified based on the analysis of individual particles by scanning electron microscopy. A total of 160 samples was collected on 38 days between February and September 2009 at a kerbside and an urban background station in the urban/industrial Ruhr area (Germany). Based on size, morphology, chemical composition and stability under electron bombardment, the 111,003 particles studied in detail were classified into the following 14 particle classes: traffic/exhaust, traffic/abrasion, traffic/resuspension, carbonaceous/organic, industry/metallurgy, industry/power plants, secondary particles, (aged) sea salt, silicates, Ca sulfates, carbonates, Fe oxides/hydroxides, biological particles, and other particles. The traffic/exhaust component consists predominantly of externally mixed soot particles and soot internally mixed with secondary particles. The traffic/abrasion component contains all particles with characteristic tracer elements (Fe, Cu, Ba, Sb, Zn) for brake and tire abrasion. The traffic/resuspension component is defined by the mixing state and comprises all internally mixed particles with a high proportion of silicates or Fe oxides/hydroxides which contain soot or abrasion particles as minor constituent. In addition, silicates and Fe oxides/hydroxides internally mixed with chlorine and sulphur containing particles were also assigned to the traffic/resuspension component. The total contribution of traffic to PM10 was found to be 27% at the urban background station and 48% at the kerbside station, the corresponding values for PM1 are 15% and 39%. These values lie within the range reported in previous literature. The relative share of the different traffic components for PM10 at the kerbside station was 27% exhaust, 15% abrasion, and 58% resuspension (38%, 8%, 54% for PM1). For the urban background, the following

Erosion and abrasion on dental structures undergoing at-home bleaching

PubMed Central

Demarco, Flávio Fernando; Meireles, Sônia Saeger; Sarmento, Hugo Ramalho; Dantas, Raquel Venâncio Fernandes; Botero, Tatiana; Tarquinio, Sandra Beatriz Chaves

2011-01-01

This review investigates erosion and abrasion in dental structures undergoing at- home bleaching. Dental erosion is a multifactorial condition that may be idiopathic or caused by a known acid source. Some bleaching agents have a pH lower than the critical level, which can cause changes in the enamel mineral content. Investigations have shown that at-home tooth bleaching with low concentrations of hydrogen or carbamide peroxide have no significant damaging effects on enamel and dentin surface properties. Most studies where erosion was observed were in vitro. Even though the treatment may cause side effects like sensitivity and gingival irritation, these usually disappear at the end of treatment. Considering the literature reviewed, we conclude that tooth bleaching agents based on hydrogen or carbamide peroxide have no clinically significant influence on enamel/dentin mineral loss caused by erosion or abrasion. Furthermore, the treatment is tolerable and safe, and any adverse effects can be easily reversed and controlled. PMID:23674914

Selected applications for current polymers in prosthetic dentistry - state of the art.

PubMed

Kawala, Maciej; Smardz, Joanna; Adamczyk, Lukasz; Grychowska, Natalia; Wieckiewicz, Mieszko

2018-05-10

Polymers are widely applied in medicine, including dentistry, i.e. in prosthodontics. The following paper is aimed at demonstrating the applications of selected modern polymers in prosthetic dentistry based on the reported literature. The study was conducted using the PubMed, SCOPUS and CINAHL databases in relation to documents published during 1999-2017. The following keywords were used: polymers with: prosthetic dentistry, impression materials, denture base materials, bite registration materials, denture soft liners, occlusal splint materials and 3D printing. Original papers and reviews which were significant from the modern clinical viewpoint and practical validity in relation to the possibility of using polymeric materials in prosthetic dentistry, were presented. Denture base materials were most commonly modified polymers. Modifications mainly concerned antimicrobial properties and reinforcement of the material structure by introducing additional fibers. Antimicrobial modifications were also common in case of relining materials. Polymeric materials have widely been used in prosthetic dentistry. Modifications of their composition allow achieving new, beneficial properties that affect quality of patients' life. Progress in science allows for a more methodologically-advanced research on the synthesis of new polymeric materials and incorporation of new substances into already known polymeric materials, that will require systematization and appropriate classification. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Forensic dentistry in human identification: A review of the literature.

PubMed

Ata-Ali, Javier; Ata-Ali, Fadi

2014-04-01

An update is provided of the literature on the role of odontology in human identification, based on a PubMed-Medline search of the last 5 years and using the terms: "forensic dentistry" (n = 464 articles), "forensic odontology" (n = 141 articles) and "forensic dentistry identification" (n = 169 articles). Apart from these initial 774 articles, others considered to be important and which were generated by a manual search and cited as references in review articles were also included. Forensic dentistry requires interdisciplinary knowledge, since the data obtained from the oral cavity can contribute to identify an individual or provide information needed in a legal process. Furthermore, the data obtained from the oral cavity can narrow the search range of an individual and play a key role in the victim identification process following mass disasters or catastrophes. This literature search covering the last 5 years describes the novelties referred to buccodental studies in comparative identification, buccodental evaluation in reconstructive identification, human bites as a method for identifying the aggressor, and the role of DNA in dental identification. The oral cavity is a rich and noninvasive source of DNA, and can be used to solve problems of a social, economic or legal nature. Key words:Forensic identification, DNA, forensic dentistry, rugoscopy, cheiloscopy, saliva.

Drill Holes and Predation Traces versus Abrasion-Induced Artifacts Revealed by Tumbling Experiments

PubMed Central

Gorzelak, Przemysław; Salamon, Mariusz A.; Trzęsiok, Dawid; Niedźwiedzki, Robert

2013-01-01

Drill holes made by predators in prey shells are widely considered to be the most unambiguous bodies of evidence of predator-prey interactions in the fossil record. However, recognition of traces of predatory origin from those formed by abiotic factors still waits for a rigorous evaluation as a prerequisite to ascertain predation intensity through geologic time and to test macroevolutionary patterns. New experimental data from tumbling various extant shells demonstrate that abrasion may leave holes strongly resembling the traces produced by drilling predators. They typically represent singular, circular to oval penetrations perpendicular to the shell surface. These data provide an alternative explanation to the drilling predation hypothesis for the origin of holes recorded in fossil shells. Although various non-morphological criteria (evaluation of holes for non-random distribution) and morphometric studies (quantification of the drill hole shape) have been employed to separate biological from abiotic traces, these are probably insufficient to exclude abrasion artifacts, consequently leading to overestimate predation intensity. As a result, from now on, we must adopt more rigorous criteria to appropriately distinguish abrasion artifacts from drill holes, such as microstructural identification of micro-rasping traces. PMID:23505530

Abrasive-assisted Nickel Electroforming Process with Moving Cathode

NASA Astrophysics Data System (ADS)

REN, Jianhua; ZHU, Zengwei; XIA, Chunqiu; QU, Ningsong; ZHU, Di

2017-03-01

In traditional electroforming process for revolving parts with complex profiles, the drawbacks on surface of deposits, such as pinholes and nodules, will lead to varying physical and mechanical properties on different parts of electroformed components. To solve the problem, compositely moving cathode is employed in abrasive-assisted electroforming of revolving parts with complicated profiles. The cathode translates and rotates simultaneously to achieve uniform friction effect on deposits without drawbacks. The influences of current density and translation speed on the microstructure and properties of the electroformed nickel layers are investigated. It is found that abrasive-assisted electroforming with compound cathode motion can effectively remove the pinholes and nodules, positively affect the crystal nucleation, and refine the grains of layer. The increase of current density will lead to coarse microstructure and lower micro hardness, from 325 HV down to 189 HV. While, faster translational linear speed produces better surface quality and higher micro hardness, from 236 HV up to 283 HV. The weld-ability of the electroformed layers are also studied through the metallurgical analysis of welded joints between nickel layer and 304 stainless steel. The electrodeposited nickel layer shows fine performance in welding. The novel compound motion of cathode promotes the mechanical properties and refines the microstructure of deposited layer.

Effect of Whitening Toothpastes on Dentin Abrasion: An In Vitro Study.

PubMed

Vieira, Gustavo Henrique Apolinario; Nogueira, Marcia Bessa; Gaio, Eduardo Jose; Rosing, Cassiano Kuchenbecker; Santiago, Sergio Lima; Rego, Rodrigo Otavio

To compare the effect of toothbrushing abrasion with hydrated silica-based whitening and regular toothpastes on root dentin using contact profilometry. Ninety dentin specimens (4 x 4 x 2 mm) were randomly divided into five experimental groups (n = 18) according to the toothpaste: three whitening (W1, W2 and W3) and two regular toothpastes (R1 and R2) produced by two different manufacturers. Using a brushing machine, each specimen was brushed with a constant load of 300 g for 2500 cycles (4.5 cycles/s). The toothpastes were diluted at a ratio of 1:3 w/w (dentifrice:distilled water). The brush diamond tip of the profilometer moved at a constant speed of 0.05 mm/s with a force of 0.7 mN. The average value of brushing abrasion in μm (mean ± SD) was obtained from five consecutive measurements of each specimen: W1 = 8.86 ± 1.58, W2 = 7.59 ± 1.04, W3 = 8.27 ± 2.39, R1 = 2.89 ± 1.05 and R2= 2.94 ± 1.29. There was a significant difference between groups (ANOVA, p<0.0001). Post-hoc Tukey's test for multiple comparisons showed differences between all the whitening and regular toothpastes, but not among the whitening nor among the regular toothpastes. The whitening toothpastes tested can cause more dentin abrasion than the regular ones.

Property-process relations in simulated clinical abrasive adjusting of dental ceramics.

PubMed

Yin, Ling

2012-12-01

This paper reports on property-process correlations in simulated clinical abrasive adjusting of a wide range of dental restorative ceramics using a dental handpiece and diamond burs. The seven materials studied included four mica-containing glass ceramics, a feldspathic porcelain, a glass-infiltrated alumina, and a yttria-stabilized tetragonal zirconia. The abrasive adjusting process was conducted under simulated clinical conditions using diamond burs and a clinical dental handpiece. An attempt was made to establish correlations between process characteristics in terms of removal rate, chipping damage, and surface finish and material mechanical properties of hardness, fracture toughness and Young's modulus. The results show that the removal rate is mainly a function of hardness, which decreases nonlinearly with hardness. No correlations were noted between the removal rates and the complex relations of hardness, Young's modulus and fracture toughness. Surface roughness was primarily a linear function of diamond grit size and was relatively independent of materials. Chipping damage in terms of the average chipping width decreased with fracture toughness except for glass-infiltrated alumina. It also had higher linear correlations with critical strain energy release rates (R²=0.66) and brittleness (R²=0.62) and a lower linear correlation with indices of brittleness (R²=0.32). Implications of these results can provide guidance for the microstructural design of dental ceramics, optimize performance, and guide the proper selection of technical parameters in clinical abrasive adjusting conducted by dental practitioners. Copyright © 2012 Elsevier Ltd. All rights reserved.

A study on practical use of underwater abrasive water jet cutting

NASA Astrophysics Data System (ADS)

Yamaguchi, Hitoshi; Demura, Kenji

1993-09-01

The practicality of underwater abrasive water jet cutting technology was studied in experiments. A study of abrasives in slurried form showed that optimum polymer concentration can be selected to suit underwater conditions. For the long-distance transport of slurry from the ocean surface to the ocean floor, a direct supply system by hose proved to be practical. This system takes advantage of the insolubility of the slurry in water due to a difference in specific gravity. For cutting thick steel plate at great ocean depths, a simulation with a pressurized container revealed the requirements for actual cutting. Confirmation of remote cutting operations will become the most important technology in field applications. Underwater sound vibration characteristics were found to change significantly in direct response to modifications in cutting conditions. This will be important basic data to develop an effective sensoring method.

Randomized Controlled Trial to Explore the Effect of Experimental Low Abrasivity Dentifrices on Enamel Gloss and Smoothness, and the Build-up of Extrinsic Tooth Stain.

PubMed

Milleman, Kimberly R; Milleman, Jeffery L; Young, Sarah; Parkinson, Charles

2017-06-01

To evaluate and compare examiner-assessed changes in enamel gloss, extrinsic dental stain, and surface smoothness following one, two, four, and eight weeks of twice-daily use of an experimental low abrasivity desensitizing dentifrice (relative dentin abrasivity [RDA] ~40) containing 5% sodium tripolyphosphate (STP) chemical cleaning agent and 1% aluminum trioxide abrasive. This was compared with an ultra-low abrasivity dentifrice (5% STP only; RDA ~13), a moderate abrasivity fluoride dentifrice (RDA ~80), and a higher abrasivity marketed whitening dentifrice (RDA ~142). This was a single-center, examiner-blind, randomized, controlled, parallel group study in healthy adults stratified by gloss score and age. Following a washout period with a conventional silica abrasive dentifrice, subjects received a dental scale and polish and were randomized to treatment. Subjects brushed their teeth for two minutes, twice daily, with their assigned dentifrice. Enamel gloss was assessed visually by comparing the facial surfaces of the maxillary incisors to the Sturzenberger gloss standards. Extrinsic dental stain was measured on the 12 anterior teeth (facial and lingual) using the Macpherson modification of the Lobene Stain Index (MLSI). Tooth smoothness was assessed using scanning electron microscope (SEM) analysis of a silicone impression of the central incisors. Of 120 screened subjects, 95 were randomized to the study. Subjects using the low abrasivity aluminum trioxide/STP dentifrice demonstrated statistically significant (p < 0.05) and increasing improvements in surface gloss over baseline at all time points, with a significant treatment effect compared to all other study dentifrices from Week 2 (p < 0.05). With respect to dental stain, the low abrasivity dentifrice group had the lowest stain score at each post-treatment time point and demonstrated statistically significantly less stain compared to all study dentifrices at Weeks 2 (p < 0.05) and 8 (p < 0.01). For tooth

75 FR 14446 - Advisory Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-25

... Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting In accordance with section... following meeting: Name: Advisory Committee on Training in Primary CareMedicine and Dentistry (ACTPCMD... Services Administration, Bureau of Health Professions, Division of Medicine and Dentistry. In the plenary...

77 FR 64116 - Advisory Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-18

... Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting In accordance with section... following meeting: Name: Advisory Committee on Training in Primary Care Medicine and Dentistry (ACTPCMD... and Dentistry, Bureau of Health Professions, Health Resources and Services Administration, Room 9A-27...

76 FR 30951 - Advisory Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-27

... Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting In accordance with section... following meeting: Name: Advisory Committee on Training in Primary Care Medicine and Dentistry (ACTPCMD.... Glass, M.D., Ph.D., Advisory Committee Executive Secretary, Division of Medicine and Dentistry, Bureau...

75 FR 36110 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-24

... University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. Notice... the New York University College of Dentistry, New York, NY. The human remains were removed from... College of Dentistry professional staff in consultation with representatives of the Alabama-Quassarte...

75 FR 64318 - Advisory Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

... Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting In accordance with section... following meeting: Name: Advisory Committee on Training in Primary Care, Medicine and Dentistry (ACTPCMD...., Ph.D., Advisory Committee Executive Secretary, Division of Medicine and Dentistry, Bureau of Health...

76 FR 64952 - Advisory Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-19

... Committee on Training in Primary Care Medicine and Dentistry; Notice of Meeting In accordance with section... following meeting: Name: Advisory Committee on Training in Primary Care, Medicine and Dentistry . Dates and... Dentistry (``Advisory Committee'') provides advice and recommendations to the Secretary of the U.S...

A systematic appraisal of the Evidence-Based Dentistry Journal.

PubMed

Mehta, Nikisha; Marshman, Zoe

2016-09-01

BackgroundThis systematic appraisal was conducted to determine if the Evidence-Based Dentistry Journal (EBDJ) acts as a reliable and contemporary source of knowledge for practitioners across all disciplines within dentistry.ObjectivesThe main objectives were to determine i) the year the articles were published and included in the EBDJ; ii) if the articles published covered all fields equally within dentistry; iii) the type of study design of the articles reported in the journal and; iv) the level of expertise of the writers of the commentaries.MethodsThis study used a systematic approach to assess the articles included in the journal. Data were extracted on the difference in the year the article was originally published and the year the article was included in the EBDJ, the number of articles in each dental discipline, the type of study designs included in the journal and the expertise of the commentators of each article. The information provided by the journal was validated by accessing the original articles through electronic databases.ResultsThe appraisal considered the 582 articles that met the inclusion criteria. Overall, 45.3% of the articles were included in the EBDJ in the same year and 44.8% of the articles were included a year after they were originally published. The number of articles varied across disciplines within dentistry: 23.7% from dental public health, 18.4% from periodontology and 11.8% from orthodontics, with only 4.6% from prosthodontics, 1% from oral pathology and 0.5% from dental materials. Most of the articles were systematic reviews and randomised controlled trials at 72% and 22.3% respectively. The writers of the commentaries were mostly academics and hospital consultants (71.2% and 13.6% commentators).ConclusionsOn the whole, it can be concluded that the journal acts as a reliable and contemporary source of knowledge/evidence for dentists, however, not all specialities within dentistry had equal coverage.

Implant dentistry in postgraduate university education. Present conditions, potential, limitations and future trends.

PubMed

Mattheos, N; Wismeijer, D; Shapira, L

2014-03-01

In recent years, opportunities for postgraduate university education in implant dentistry have increased significantly, with an increase in both the number but also the complexity of available postgraduate programmes. However, there appears to be a lack of standards directing the learning outcomes of such programmes. A scientific literature search was conducted for publications reporting on university programmes within implant dentistry, including description of programmes and evaluation of learning outcomes. A separate Internet search was conducted to collect information on existing university programmes as presented on university websites. Implant dentistry has reached a critical mass of an independent, multidisciplinary and vibrant domain of science, which combines knowledge and discovery from many clinical and basic sciences. Many university programmes conclude with a master's or equivalent degree, but there appears to be a great diversity with regard to duration and learning objectives, as well as targeted skills and competences. The importance of implant dentistry has also increased within established specialist training programmes. There was little indication, however, that the comprehensive aspects of implant dentistry are present in all specialist training programmes where implants are being covered. Although universities should maintain the options of designing academic programmes as they best see fit, it is imperative for them to introduce some form of transparent and comparable criteria, which will allow the profession and the public to relate the degree and academic credentials to the actual skills and competences of the degree holder. With regard to established specialist training programmes, the interdisciplinary and comprehensive nature of implant dentistry needs to be emphasised, covering both surgical and restorative aspects. Finally, implant dentistry is not, at present, a dental specialty. The profession has not reached a consensus as to whether

Tooth brush abrasion of paint-on resins for shade modification of crown and bridge resins.

PubMed

Fujii, Koichi; Ban, Seiji; McCabe, John F

2003-09-01

The purpose of this study was to evaluate the surface roughness and resistance to toothbrush abrasion of three experimental paint-on composite resins developed for the shade modification of crown and bridge resins. The paint-on resins had less filler volume fraction than restorative composites or the crown and bridge resins and consequently were of low viscosity. The maximum surface roughness (Rmax) and the maximum depth loss by abrasion for the paint-on resins following 40,000 cycles of brushing ranged from 2.45 to 4.07 microm and 8.63 to 13.67 microm, respectively. Rmax values were 37.7-67.5% lower than that for the crown and bridge resin subjected to the same test. Wear depth was 19.9-49.4% lower than for the crown and bridge resin. These results suggest that the paint-on resins are expected to have adequate resistance to toothbrush abrasion and may therefore be suitable for clinical use.

Perceived competency towards preventive dentistry among dental graduates: the need for curriculum change

PubMed Central

Arheiam, Arheiam; Bankia, Ibtesam; Ingafou, Mohamed

2015-01-01

Background A previous study has shown that dental practitioners in Benghazi believed that the less prevention-oriented education system is one of the barriers to applying preventive dentistry. Objective To assess attitudes and perceived competence of the dental graduates in Benghazi towards prevention and early management of dental caries. Methods A cross-sectional, questionnaire-based survey was conducted among internship students attending the Department of Community and Preventive Dentistry in Faculty of Dentistry, Benghazi, Libya. The participants were asked to provide demographic information, to respond to statements about their attitudes towards preventive dentistry, and to answer questions regarding their perceived competence in applying preventive dentistry procedures. Results Data from 108 Libyan dental graduates were analysed for this study, of which 64% of them were females and 42.1% of them passed their final year with grade: acceptable. The most acknowledged aspects of preventive dentistry were being useful and essential to the community (95.4 and 90.8%, respectively). The percentage of participants expressing a proficiency in providing oral hygiene instructions was the highest (95.4%). There were differences between study subgroups in their perceived competence of preventive dental practices by gender and academic performance (p≤0.05). Conclusion This study highlighted that the currently implemented undergraduate education programme in Benghazi dental school does not provide dentists with the required attitude and skills to fulfil their role in providing preventive-oriented health services. PMID:25556523

75 FR 52021 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-24

... University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. Notice... University College of Dentistry, New York, NY. The human remains were removed from an unknown location. This... the human remains was made by New York University College of Dentistry professional staff in...

77 FR 42507 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... Inventory Completion: New York University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The New York University College of Dentistry has completed an inventory... the New York University College of Dentistry. Disposition of the human remains to the Indian tribes...

77 FR 42513 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... Inventory Completion: New York University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The New York University College of Dentistry has completed an inventory... the New York University College of Dentistry. Disposition of the human remains to the Indian tribes...

75 FR 33329 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. Notice... and control of the New York University College of Dentistry, New York, NY. The human remains were... College of Dentistry professional staff in consultation with representatives of the Tuscarora Nation of...

75 FR 52021 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-24

... University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. Notice... University College of Dentistry, New York, NY. The human remains were removed from Port Clarence, Nome County... the human remains was made by New York University College of Dentistry professional staff in...

77 FR 42508 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... Inventory Completion: New York University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The New York University College of Dentistry has completed an inventory... the New York University College of Dentistry. Repatriation of the human remains to the Indian tribes...

The impact of managed care in dentistry.

PubMed

Clouse, H R

1999-01-01

Managed care plans attempt to control health care expenditures aggressively. These plans directly influence access to medical care and the type, level, and frequency of care rendered. As a result, hospital stays are reduced, focus shifts from inpatient to outpatient care, and patients are responsible for a larger share of health care costs. Dentistry is not immune from the impact of managed care. The attractiveness of the dental market has drawn many managed care organizations, insurers, and entrepreneurs to encourage dentists to participate in a wide variety of managed care programs. However, the delivery of dental care differs markedly in many respects from that of medical care. Therefore, many of the cost saving aspects of managed care that have been so successful in medicine may not result in similar cost savings in dentistry.

The rock abrasion record at Gale Crater: Mars Science Laboratory results from Bradbury Landing to Rocknest

USGS Publications Warehouse

Bridges, N.T.; Calef, F.J.; Hallett, B.W.; Herkenhoff, Kenneth E.; Lanza, N.L.; Le Mouélic, S.; Newman, C.E.; Blaney, D.L.; de Pablo, M.A.; Kocurek, G.A.; Langevin, Y.; Lewis, K.W.; Mangold, N.; Maurice, S.; Meslin, P.-Y.; Pinet, P.; Renno, N.O.; Rice, CM.S.; Richardson, M.E.; Sautter, V.; Sletten, R.S.; Wiens, R.C.; Yingst, R.A.

2014-01-01

Ventifacts, rocks abraded by wind-borne particles, are found in Gale Crater, Mars. In the eastward drive from “Bradbury Landing” to “Rocknest,” they account for about half of the float and outcrop seen by Curiosity's cameras. Many are faceted and exhibit abrasion textures found at a range of scales, from submillimeter lineations to centimeter-scale facets, scallops, flutes, and grooves. The drive path geometry in the first 100 sols of the mission emphasized the identification of abrasion facets and textures formed by westerly flow. This upwind direction is inconsistent with predictions based on models and the orientation of regional dunes, suggesting that these ventifact features formed from very rare high-speed winds. The absence of active sand and evidence for deflation in the area indicates that most of the ventifacts are fossil features experiencing little abrasion today.

[Brazilian bibliographical output on public oral health in public health and dentistry journals].

PubMed

Celeste, Roger Keller; Warmling, Cristine Maria

2014-06-01

The scope of this paper is to describe characteristics of the scientific output in the area of public oral health in journals on public health and dentistry nationwide. The Scopus database of abstracts and quotations was used and eight journals in public health, as well as ten in dentistry, dating from 1947 to 2011 were selected. A research strategy using key words regarding oral health in public health and key words about public health in dentistry was used to locate articles. The themes selected were based on the frequency of key words. Of the total number of articles, 4.7% (n = 642) were found in oral health journals and 6.8% (n = 245) in public health journals. Among the authors who published most, only 12% published in both fields. There was a percentile growth of public oral health publications in dentistry journals, though not in public health journals. In dentistry, only studies indexed as being on the topic of epidemiology showed an increase. In the area of public health, planning was predominant in all the phases studied. Research to evaluate the impact of research and postgraduate policies in scientific production is required.

[Practice and experience in early clinical education of dental students in preventive dentistry].

PubMed

Tao, Dan-ying; Shu, Chen-bin; Pan, Ying; Feng, Xi-ping

2013-02-01

To help dental students acquaint the medical environment, doctor-patient communication and relationship, early clinic education was arranged in our college of stomatology. The interesting topics were chosen to enhance the learning enthusiasm of the students in the teaching practice of preventive dentistry. Students were encouraged to practice the skill of doctor-patient communication. To obtain the satisfactory teaching effect and aim, it was important to pay attention to the aspects in the groups and clinical practice. Early clinic education in preventive dentistry help the students understand the specialty of preventive dentistry.

Distance Learning: Effectiveness of an Interdisciplinary Course in Speech Pathology and Dentistry

ERIC Educational Resources Information Center

Ramos, Janine Santos; da Silva, Letícia Korb; Pinzan, Arnaldo; de Castro Rodrigues, Antonio; Berretin-Felix, Giédre

2015-01-01

Objective: Evaluate the effectiveness of distance learning courses for the purpose of interdisciplinary continuing education in Speech Pathology and Dentistry. Methods: The online course was made available on the Moodle platform. A total of 30 undergraduates participated in the study (15 from the Dentistry course and 15 from the Speech Pathology…

75 FR 33329 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... University College of Dentistry, New York, NY AGENCY: National Park Service, Interior. ACTION: Notice. Notice... the New York University College of Dentistry, New York, NY. The human remains were removed from.... A detailed assessment of the human remains was made by the New York University College of Dentistry...

Toothbrush abrasion, simulated tongue friction and attrition of eroded bovine enamel in vitro.

PubMed

Vieira, A; Overweg, E; Ruben, J L; Huysmans, M C D N J M

2006-05-01

Enamel erosion results in the formation of a softened layer that is susceptible to disruption by mechanical factors such as brushing abrasion, tongue friction and attrition. The aim of this study was to investigate the individual contribution of those mechanical insults to the enamel loss caused by dental erosion. Forty two bovine enamel samples were randomly divided into seven groups (n=6 per group) that were submitted to 3cycles of one of the following regimes: erosion and remineralization (er/remin); toothbrush abrasion and remineralization (abr/remin); erosion, toothbrush abrasion and remineralization (er/abr/remin); attrition and remineralization (at/remin); erosion, attrition and remineralization (er/at/remin); simulated tongue friction and remineralization (tg/remin); erosion, simulated tongue friction and remineralization (er/tg/remin). Erosion took place in a demineralization solution (50mM citric acid, pH 3) for 10min under agitation. Brushing abrasion, tongue friction and attrition were simulated for 1min using a home-made wear device. Remineralization was carried out in artificial saliva for 2h. Enamel loss was quantified using optical profilometry. One-way ANOVA indicated a significant difference between the amounts of enamel lost due to the different wear regimes (p

Abrasive Wear Resistance of Tool Steels Evaluated by the Pin-on-Disc Testing

NASA Astrophysics Data System (ADS)

Bressan, José Divo; Schopf, Roberto Alexandre

2011-05-01

Present work examines tool steels abrasion wear resistance and the abrasion mechanisms which are one main contributor to failure of tooling in metal forming industry. Tooling used in cutting and metal forming processes without lubrication fails due to this type of wear. In the workshop and engineering practice, it is common to relate wear resistance as function of material hardness only. However, there are others parameters which influences wear such as: fracture toughness, type of crystalline structure and the occurrence of hard precipitate in the metallic matrix and also its nature. In the present investigation, the wear mechanisms acting in tool steels were analyzed and, by normalized tests, wear resistance performance of nine different types of tool steels were evaluated by pin-on-disc testing. Conventional tool steels commonly used in tooling such as AISI H13 and AISI A2 were compared in relation to tool steels fabricated by sintering process such as Crucible CPM 3V, CPM 9V and M4 steels. Friction and wear testing were carried out in a pin-on-disc automated equipment which pin was tool steel and the counter-face was a abrasive disc of silicon carbide. Normal load of 5 N, sliding velocity of 0.45 m/s, total sliding distance of 3000 m and room temperature were employed. The wear rate was calculated by the Archard's equation and from the plotted graphs of pin cumulated volume loss versus sliding distance. Specimens were appropriately heat treated by quenching and three tempering cycles. Percentage of alloying elements, metallographic analyses of microstructure and Vickers microhardness of specimens were performed, analyzed and correlated with wear rate. The work is concluded by the presentation of a rank of tool steel wear rate, comparing the different tool steel abrasion wear resistance: the best tool steel wear resistance evaluated was the Crucible CPM 9V steel.

Recent advances in dental optics - Part I: 3D intraoral scanners for restorative dentistry

NASA Astrophysics Data System (ADS)

Logozzo, Silvia; Zanetti, Elisabetta M.; Franceschini, Giordano; Kilpelä, Ari; Mäkynen, Anssi

2014-03-01

Intra-oral scanning technology is a very fast-growing field in dentistry since it responds to the need of an accurate three-dimensional mapping of the mouth, as required in a large number of procedures such as restorative dentistry and orthodontics. Nowadays, more than 10 intra-oral scanning devices for restorative dentistry have been developed all over the world even if only some of those devices are currently available on the market. All the existing intraoral scanners try to face with problems and disadvantages of traditional impression fabrication process and are based on different non-contact optical technologies and principles. The aim of this publication is to provide an extensive review of existing intraoral scanners for restorative dentistry evaluating their working principles, features and performances.

Correlating field and laboratory rates of particle abrasion, Rio Medio, Sangre de Cristo Mountains, New Mexico

NASA Astrophysics Data System (ADS)

Polito, P. J.; Sklar, L. S.

2006-12-01

River bed sediments commonly fine downstream due to a combination of particle abrasion, selective transport of finer grains, and fining of the local sediment supply from hillslopes and tributaries. Particle abrasion rates can be directly measured in the laboratory using tumbling barrels and annular flumes, however, scaling experimental particle abrasion rates to the field has proven difficult due to the confounding effects of selective transport and local supply variations. Here we attempt to correlate laboratory and field rates of particle abrasion in a field setting where these confounding effects can be controlled. The Rio Medio, which flows westward from the crest of the Sangre de Cristo Mountains in north central New Mexico, is one of several streams studied by John P. Miller in the early 1960's. Several kilometers downstream of its headwaters, the river crosses the Picuris-Pecos fault. Upstream of the fault the river receives quartzite, sandstone and shale clasts from the Ortega Formation, while downstream sediments are supplied by the Embudo Granite. Because the upstream lithologies are not resupplied downstream of the fault, any observed fining of these clasts should be due only to abrasion and selective transport. We hypothesize that we can account for the effects of selective transport by comparing relative fining rates for the different upstream lithologies from both the field and a laboratory tumbler. By correlating laboratory abrasion rates with rock strength, we can predict the relative fining rates due solely to abrasion expected in the field; differences between the predicted and observed fining rates could then be attributed to selective transport. We used point counts to measure bed surface sediment grain size distributions at 15 locations along a 25 kilometer reach of the Rio Medio, beginning just downstream of the fault and ending upstream of a developed area with disturbed channel conditions. We recorded intermediate particle diameter as well

The specialty of family dentistry: a future for general dental practitioners?

PubMed

Li, R W; Chow, T W

2004-01-01

A new Specialty in dentistry, Family Dentistry, has been established to provide a structured, co-ordinated training for general dental practitioners who are the major oral health service providers. The training emphasizes the importance of continuing and comprehensive care, the interface between primary and secondary care, the relationship between the patient and his/her family and the community, and a holistic approach in treatment planning and delivery.

Continuous Monitoring of Pin Tip Wear and Penetration into Rock Surface Using a New Cerchar Abrasivity Testing Device

NASA Astrophysics Data System (ADS)

Hamzaban, Mohammad-Taghi; Memarian, Hossein; Rostami, Jamal

2014-03-01

Evaluation of rock abrasivity is important when utilizing mechanized excavation in various mining and civil projects in hard rock. This is due to the need for proper selection of the rock cutting tools, estimation of the tool wear, machine downtime for cutter change, and costs. The Cerchar Abrasion Index (CAI) test is one of the simplest and most widely used methods for evaluating rock abrasivity. In this study, a new device for the determination of frictional forces and depth of pin penetration into the rock surface during a Cerchar test is discussed. The measured parameters were used to develop an analytical model for calculation of the size of the wear flat (and hence a continuous measure of CAI as the pin moves over the sample) and pin tip penetration into the rock during the test. Based on this model, continuous curves of CAI changes and pin tip penetration into the rock were plotted. Results of the model were used for introduction of a new parameter describing rock-pin interaction and classification of rock abrasion.

Can Dentistry Have Two Contracts with the Public?

PubMed

Nash, David A

2015-01-01

The social contract is an implicit agreement between parts of society and society as a whole. Since the Middle Ages, the learned professions, recently including dentistry, have had a covenantal relationship with the public based on trust, exchanging monopoly privileges for benefiting the public good. Unlike commercial trade in commodities, professional relationships are grounded in ensuring an adequate level of oral health to all. A second contract is emerging where dentists relate to society as business operators, exchanging commodity services for a price. Recent actions by the Federal Trade Commission and the U.S. Supreme Court make it unlikely that dentistry will be able to enjoy only selected aspects of each contract while avoiding obligations that it finds unfavorable.

The efficacy of mechanical abrasion and talc slurry as methods of pleurodesis in normal dogs.

PubMed

Jerram, R M; Fossum, T W; Berridge, B R; Steinheimer, D N; Slater, M R

1999-01-01

To determine the efficacy of mechanical abrasion and talc slurry as methods for pleurodesis in normal dogs. Experimental study. Ten normal beagle dogs. Group I dogs had mechanical abrasion (MA) of the pulmonary and costal pleurae performed in one hemithorax with a dry gauze sponge with a median sternotomy approach. Group II dogs had 100 mL of a 1 g talc slurry (TS) administered into one hemithorax through a tube thoracostomy. Administration of the TS was visualized by using video thoracoscopy. All dogs were evaluated at 2, 10, 20, and 30 days postoperatively by means of thoracic radiography and ultrasonographic thoracic wall measurement. The dogs were euthanatized 30 days postoperatively and a gross necropsy was performed. Hemithoraces were assigned a pleurodesis score (0-4) and an obliteration grade (0-6). Tissues were collected for histopathologic examination of pulmonary pleura, costal pleura, and pleural adhesions. Pulmonary and costal pleurae were graded for the degree of fibrosis (0-4). Obliteration grade and costal pleural fibrosis score were significantly higher for the treated sides in the MA dogs compared with the TS dogs. MA Dogs: Mechanical abrasion dogs had pleurodesis, obliteration, and pleural fibrosis scores that were greater on the treated side than the untreated side, however, the differences were not statistically significant. Only two MA dogs had firm adhesion of the pulmonary pleura to the costal pleura in portions of the cranial and middle lung lobes in the treated hemithorax. Thoracic wall surface area covered with adhesions was 15% and 21% in each of these two dogs. The median pulmonary pleural fibrosis score of all MA dogs for the treated hemithorax was 3 compared to 0 on the untreated side. TS Dogs: There was no statistical difference for pleurodesis scores and obliteration grades between the treated and untreated sides. No dogs showed evidence of pulmonary to costal pleural adhesions. Histopathology showed talc crossover into the

75 FR 69686 - Advisory Committee on Training in Primary Care Medicine and Dentistry

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Health Resources and Services Administration Advisory Committee on Training in Primary Care Medicine and Dentistry AGENCY: Health Resources and Services... of the Advisory Committee on Training in Primary Care Medicine and Dentistry, November 15, 2010, 8:30...

The role of the microfissuration of the rock matrix in the abrasion resistance of ornamental granitic rocks

NASA Astrophysics Data System (ADS)

Rodríguez-Rey, Angel; Sanchez-Delgado, Nuria; Camino, Clara; Calleja, Lope; Ruiz de Argandoña, Vicente G.; Setien, Alexia

2015-04-01

The microcrack density and the abrasion resistance of five ornamental granites (Albero, Gris Alba, Mondariz, Rosa Porriño and Traspieles) from Galicia (NW Spain) have been quantified as part of a research aimed to interpret the cuttability of the rocks in relation to the petrophysical properties of the rock matrix. Large blocks from the quarries have been cut with an industrial saw and the microcrack density and the abrasion resistance have been measured in two surfaces: H, parallel to the cut surface; T, perpendicular both to the cut surface and the cutting direction. Both planes are perpendicular to the rift plane, as it is known in quarry works. The microcrack density has been quantified following an stereological procedure applied to polished sections imaged under scanning electron microscopy. The magnification of the images allowed the study of microcracks as narrow as 2 microns in aperture. The density has been quantified in terms of length of microcrack traces per surface unit so possible anisotropies of the microcrack network could be detected. The obtained values are in the typical range for this type of rocks although the Traspieles granite shows a higher value due to its weathering degree (H: 5.11, T: 5.37 mm/mm2). The values measured in the two surfaces (H and T) are quite similar in four of the rocks; only the Albero granite shows a marked anisotropy (H: 2.76 T: 3.53 mm/mm2). The abrasion resistance of the rocks has been measured following the european standard EN 14157:2004 using the capon method. The rocks can be classified in two groups according to their abrasion resistance. Rosa Porriño, Gris Alba and Mondariz granites are the more resistant to abrasion with values around 16-17 mm. Albero and Traspieles granites are less resistant with values higher than 19 mm. The results show a good correlation between the microcrack density and the abrasion resistance. As can be expected the rocks with high microcrack density show low abrasion resistance. The

Interior design for dentistry.

PubMed

Unthank, M; True, G

1999-11-01

In the increasingly complex, competitive and stressful field of dentistry, effectively designed dental offices can offer significant benefits. Esthetic, functional and life-cycle cost issues to be considered when developing your interior design scheme include color, finishes, lighting, furnishings, art and accessories. An appropriately designed dental office serves as a valuable marketing tool for your practice, as well as a safe and enjoyable work environment. Qualified interior design professionals can help you make design decisions that can yield optimum results within your budget.

Particle size and composition distribution analysis of automotive brake abrasion dusts for the evaluation of antimony sources of airborne particulate matter

NASA Astrophysics Data System (ADS)

Iijima, Akihiro; Sato, Keiichi; Yano, Kiyoko; Tago, Hiroshi; Kato, Masahiko; Kimura, Hirokazu; Furuta, Naoki

Abrasion dusts from three types of commercially available non-steel brake pads were generated by a brake dynamometer at disk temperatures of 200, 300 and 400 °C. The number concentration of the abrasion dusts and their aerodynamic diameters ( Dp) were measured by using an aerodynamic particle sizer (APS) spectrometer with high temporal and size resolution. Simultaneously, the abrasion dusts were also collected based on their size by using an Andersen low-volume sampler, and the concentrations of metallic elements (K, Ti, Fe, Cu, Zn, Sb and Ba) in the size-classified dusts were measured by ICP-AES and ICP-MS. The number distributions of the brake abrasion dusts had a peak at Dp values of 1 and 2 μm; this peak shifted to the coarse side with an increase in the disk temperature. The mass distributions calculated from the number distributions have peaks between Dp values of 3 and 6 μm. The shapes of the elemental mass distributions (Ti, Fe, Cu, Zn, Sb and Ba) in size-classified dusts were very similar to the total mass distributions of the brake abrasion dusts. These experimental results indicated that the properties of brake abrasion dusts were consistent with the characteristics of Sb-enriched fine airborne particulate matter. Based on these findings and statistical data, the estimation of Sb emission as airborne particulate matter from friction brakes was also discussed.

Future impact of nanotechnology on medicine and dentistry

PubMed Central

Patil, Mallanagouda; Mehta, Dhoom Singh; Guvva, Sowjanya

2008-01-01

The human characteristics of curiosity, wonder, and ingenuity are as old as mankind. People around the world have been harnessing their curiosity into inquiry and the process of scientific methodology. Recent years have witnessed an unprecedented growth in research in the area of nanoscience. There is increasing optimism that nanotechnology applied to medicine and dentistry will bring significant advances in the diagnosis, treatment, and prevention of disease. Growing interest in the future medical applications of nanotechnology is leading to the emergence of a new field called nanomedicine. Nanomedicine needs to overcome the challenges for its application, to improve the understanding of pathophysiologic basis of disease, bring more sophisticated diagnostic opportunities, and yield more effective therapies and preventive properties. When doctors gain access to medical robots, they will be able to quickly cure most known diseases that hobble and kill people today, to rapidly repair most physical injuries our bodies can suffer, and to vastly extend the human health span. Molecular technology is destined to become the core technology underlying all of 21st century medicine and dentistry. In this article, we have made an attempt to have an early glimpse on future impact of nanotechnology in medicine and dentistry. PMID:20142942

Study motives, career choices and interest in paediatric dentistry among final year dental students in Nigeria

PubMed Central

2014-01-01

Background Students’ motives for studying Dentistry have been a subject of interest for years because of the potential for understanding the psychological makeup and subsequent job satisfaction for the dentist. It is also useful in identifying expectations of the profession. This study therefore tried to identify study motives and career preferences of dental students especially with respect to the practice of paediatric dentistry. Methods This was a cross-sectional study using a self-administered questionnaire. The final year students in six dental schools in Nigeria were required to fill the questionnaire. Students were asked to rank their motives and career preferences on a Likert like scale with points ranging from 0–5 where 0 represented a factor that had no influence on their decision and 5 represented a very influential factor. The underlying dimensions for study motives, career preference, impression about and motive for interest in the practice of paediatric dentistry were identified using factor analysis. Results One hundred and seventy nine of 223 students (80.3%) participated in this study. Motives for the practice of dentistry included characteristics of the profession, altruism and intellectual challenges, existence of artistic theme in dentistry and parent’s recommendation. Overall, 67.1% of respondents indicated interest in postgraduate studies and 50.8% were interested in paediatric dentistry practice. The main motives for showing interest in the practice of paediatric dentistry were ‘personal interest, professional interest and interest of significant others in children’, and ‘family influence’. Significantly more males than females were interested in the practice of paediatric dentistry though the motives for interest in the practice of paediatric dentistry did not differ significantly by sex or age. Conclusion The non-significant sex difference in the motives for interest in the practice of paediatric dentistry is a possible

Abrasion and Fragmentation Processes in Marly Sediment Transport

NASA Astrophysics Data System (ADS)

Le Bouteiller, C.; Naaim, F.; Mathys, N.; Lave, J.; Kaitna, R.

2009-04-01

In the highly erosive marly catchments of Draix (Southern Alps, France), downstream fining of sediments has been observed and can not be explained by selective sorting. Moreover, high concentrations of suspended fine sediment (up to 800 g/L) are measured during flood events in these basins. These observations lead to the hypothesis that abrasion and fragmentation of marly sediments during transport play an important role in the production of fine sediments. Several experiments are conducted in order to quantify these processes: material from the river bed is introduced into the water flow in a circular flume as well as in a large scale rotating drum. Abrasion rates range from 5 to 15%/km, depending on the lithology: marls from the upper basin are more erosive than those from the lower basin. Modifications of grain size distribution in the rough fraction are also observed. Field measurements are also conducted. Downstream of the main marly sediment sources, the river bed is composed of marls and limestone pebbles. We have sampled the river bed for analysis of grain size distribution and lithology. First results show a decrease of the proportion of marls along the river bed. This is in accordance with the high erosion rates observed in our laboratory experiments. Further investigations are planned in order to study more precisely marl grain size distribution, especially in the finer fraction.

The Modern Value of Early Writings in Medicine and Dentistry.

PubMed

Peck, Sheldon

2016-01-01

This article illustrates three examples supporting the modern value of early writings in dentistry and medicine. First, by studying cases described in works published long before the era of genetic science, we are able to develop new hypotheses about familial conditions and their genetic roots. Tooth transposition is presented as an example. Second, old writings may lead us to valuable historical insights and perspectives in medicine that can be revealed only in retrospective analysis. An example of this kind of historical analysis uncovers why dentistry became unnaturally separated from mainstream medicine in the 19th century. Third, early writings become keys to unlocking forgotten knowledge that enriches our understanding of historically significant people and events. The discovery of Norman Kingsley's long forgotten pyrographic paintings after Rembrandt portraits is used as an example. Libraries, the traditional custodians of these valued old texts, must continue to be supported, and not undermined by the paperless digital revolution. Copyright American Academy of the History of Dentistry.

Uses of electromyography in dentistry: An overview with meta-analysis.

PubMed

Nishi, Shamima Easmin; Basri, Rehana; Alam, Mohammad Khursheed

2016-01-01

The purpose of this study was to review the uses of electromyography (EMG) in dentistry in the last few years in related research. EMG is an advanced technique to record and evaluate muscle activity. In the previous days, EMG was only used for medical sciences, but now EMG playing a tremendous role in medical as well as dental sector. Several electronic databases such as Google Scholar, PubMed, Science Direct, and Web of Science were systematically searched for studies published until July 2015. EMG can be used in both diagnosis and treatment purpose to record neuromuscular activity. In dentistry, we can utilize EMG to evaluate muscular activity in function such as chewing and biting or parafunctional activities such as clenching and bruxism. In case of TMJ and myofascial pain disorders, EMG widely is used in the last few years. EMG is one of biometric tests that occur in the modern evidence-based dentistry practice.

Prediction Of Abrasive And Diffusive Tool Wear Mechanisms In Machining

NASA Astrophysics Data System (ADS)

Rizzuti, S.; Umbrello, D.

2011-01-01

Tool wear prediction is regarded as very important task in order to maximize tool performance, minimize cutting costs and improve the quality of workpiece in cutting. In this research work, an experimental campaign was carried out at the varying of cutting conditions with the aim to measure both crater and flank tool wear, during machining of an AISI 1045 with an uncoated carbide tool P40. Parallel a FEM-based analysis was developed in order to study the tool wear mechanisms, taking also into account the influence of the cutting conditions and the temperature reached on the tool surfaces. The results show that, when the temperature of the tool rake surface is lower than the activation temperature of the diffusive phenomenon, the wear rate can be estimated applying an abrasive model. In contrast, in the tool area where the temperature is higher than the diffusive activation temperature, the wear rate can be evaluated applying a diffusive model. Finally, for a temperature ranges within the above cited values an adopted abrasive-diffusive wear model furnished the possibility to correctly evaluate the tool wear phenomena.

[Curriculum reform and research in dentistry at the undergraduate level: history under construction].

PubMed

Maltagliati, Luciana Avila; Goldenberg, Paulete

2007-01-01

Approaching from the perspective of curriculum organization, the article examines the development of undergraduate research in dentistry. Based on Brazilian and international printed or electronic publications, the authors examine the institutionalization of higher education in dentistry, university reform, and the enactment of Curriculum Guidelines. From the earliest days of higher education in dentistry, there has been a concern with research. But Brazil's university reform assigned research to graduate studies and scientific instruction to undergraduate studies. In recent years, Curriculum Guidelines have reconsidered the position of research and have recommended changes that allow research to be viewed as an educational principle.

77 FR 42510 - Notice of Inventory Completion: New York University College of Dentistry, New York, NY; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-19

... Inventory Completion: New York University College of Dentistry, New York, NY; Correction AGENCY: National... of human remains under the control of the New York University College of Dentistry, New York, NY. The... Dentistry professional staff in consultation with representatives of the Delaware Nation of Oklahoma...

Performance analysis of cutting graphite-epoxy composite using a 90,000psi abrasive waterjet

NASA Astrophysics Data System (ADS)

Choppali, Aiswarya

Graphite-epoxy composites are being widely used in many aerospace and structural applications because of their properties: which include lighter weight, higher strength to weight ratio and a greater flexibility in design. However, the inherent anisotropy of these composites makes it difficult to machine them using conventional methods. To overcome the major issues that develop with conventional machining such as fiber pull out, delamination, heat generation and high tooling costs, an effort is herein made to study abrasive waterjet machining of composites. An abrasive waterjet is used to cut 1" thick graphite epoxy composites based on baseline data obtained from the cutting of ¼" thick material. The objective of this project is to study the surface roughness of the cut surface with a focus on demonstrating the benefits of using higher pressures for cutting composites. The effects of major cutting parameters: jet pressure, traverse speed, abrasive feed rate and cutting head size are studied at different levels. Statistical analysis of the experimental data provides an understanding of the effect of the process parameters on surface roughness. Additionally, the effect of these parameters on the taper angle of the cut is studied. The data is analyzed to obtain a set of process parameters that optimize the cutting of 1" thick graphite-epoxy composite. The statistical analysis is used to validate the experimental data. Costs involved in the cutting process are investigated in term of abrasive consumed to better understand and illustrate the practical benefits of using higher pressures. It is demonstrated that, as pressure increased, ultra-high pressure waterjets produced a better surface quality at a faster traverse rate with lower costs.

Release of copper-amended particles from micronized copper-pressure-treated wood during mechanical abrasion.

PubMed

Civardi, Chiara; Schlagenhauf, Lukas; Kaiser, Jean-Pierre; Hirsch, Cordula; Mucchino, Claudio; Wichser, Adrian; Wick, Peter; Schwarze, Francis W M R

2016-11-28

We investigated the particles released due to abrasion of wood surfaces pressure-treated with micronized copper azole (MCA) wood preservative and we gathered preliminary data on its in vitro cytotoxicity for lung cells. The data were compared with particles released after abrasion of untreated, water (0% MCA)-pressure-treated, chromated copper (CC)-pressure-treated wood, and varnished wood. Size, morphology, and composition of the released particles were analyzed. Our results indicate that the abrasion of MCA-pressure-treated wood does not cause an additional release of nanoparticles from the unreacted copper (Cu) carbonate nanoparticles from of the MCA formulation. However, a small amount of released Cu was detected in the nanosized fraction of wood dust, which could penetrate the deep lungs. The acute cytotoxicity studies were performed on a human lung epithelial cell line and human macrophages derived from a monocytic cell line. These cell types are likely to encounter the released wood particles after inhalation. Our findings indicate that under the experimental conditions chosen, MCA does not pose a specific additional nano-risk, i.e. there is no additional release of nanoparticles and no specific nano-toxicity for lung epithelial cells and macrophages.

Eminent Victorian dentistry. 2. John Ruskin and the patient experience of Victorian dentistry. Ruskin's mouth and teeth.

PubMed

Bishop, M G H

2011-03-12

This paper is the second of two which examine Victorian attitudes to dentists and dentistry through the diaries and writings of John Ruskin (1819-1900). In the first paper Ruskin's relationship with his dentist was described. In this paper, the history of his mouth, teeth, and dental disease is examined.

The Risk of Bias in Randomized Trials in General Dentistry Journals.

PubMed

Hinton, Stephanie; Beyari, Mohammed M; Madden, Kim; Lamfon, Hanadi A

2015-01-01

The use of a randomized controlled trial (RCT) research design is considered the gold standard for conducting evidence-based clinical research. In this present study, we aimed to assess the quality of RCTs in dentistry and create a general foundation for evidence-based dentistry on which to perform subsequent RCTs. We conducted a systematic assessment of bias of RCTs in seven general dentistry journals published between January 2011 and March 2012. We extracted study characteristics in duplicate and assessed each trial's quality using the Cochrane Risk of Bias tool. We compared risk of bias across studies graphically. Among 1,755 studies across seven journals, we identified 67 RCTs. Many included studies were conducted in Europe (39%), with an average sample size of 358 participants. These studies included 52% female participants and the maximum follow-up period was 13 years. Overall, we found a high percentage of unclear risk of bias among included RCTs, indicating poor quality of reporting within the included studies. An overall high proportion of trials with an "unclear risk of bias" suggests the need for better quality of reporting in dentistry. As such, key concepts in dental research and future trials should focus on high-quality reporting.

The future of pediatric dentistry education and curricula: a Chilean perspective.

PubMed

Mariño, Rodrigo; Ramos-Gómez, Francisco; Manton, David John; Onetto, Juan Eduardo; Hugo, Fernando; Feldens, Carlos Alberto; Bedi, Raman; Uribe, Sergio; Zillmann, Gisela

2016-07-18

A meeting was organised to consolidate a network of researchers and academics from Australia, Brazil, Chile, the UK and the USA, relating to Early Childhood Caries (ECC) and Dental Trauma (DT). As part of this meeting, a dedicated session was held on the future of paediatric dental education and curricula. Twenty-four paediatric dentistry (PD) academics, representing eight Chilean dental schools, and three international specialists (from Brazil and Latvia) participated in group discussions facilitated by five members of the ECC/DT International Collaborative Network. Data were collected from group discussions which followed themes developed as guides to identify key issues associated with paediatric dentistry education, training and research. Participants discussed current PD dental curricula in Chile, experiences in educating new cohorts of oral health care providers, and the outcomes of existing efforts in education and research in PD. They also, identified challenges, opportunities and areas in need of further development. This paper provides an introspective analysis of the education and training of PD in Chile; describes the input provided by participants into pediatric dentistry education and curricula; and sets out some key priorities for action with suggested directions to best prepare the future dental workforce to maximise oral health outcomes for children. Immediate priorities for action in paediatric dentistry in Chile were proposed.

Dentistry in the 21st century: challenges of a globalising world.

PubMed

Hayashi, Mikako; Haapasalo, Markus; Imazato, Satoshi; Lee, Jae Il; Momoi, Yasuko; Murakami, Shinya; Whelton, Helen; Wilson, Nairn

2014-12-01

Oral health is - literally - vital to good general health, not least because the mouth is the sentinel of the body. Dentistry, the Cinderella of health care, faces immense challenges of globalisation. Governments, having spent freely on everything from defence to social security, face mountains of debts which make budget cutbacks essential. Simultaneously, most developed countries have to pay increasing costs of caring for rapidly ageing populations. Dentistry is being pulled two ways: wealthy members of society demand high-end expensive treatment, much of it cosmetic rather than necessary to deal with disease, whereas many millions of poor people in developing countries cannot afford basic dental treatment and may never see a dentist. Too many governments and dentists persist with the expensive and destructive regime of 'drill and fill (and bill)'. International advances in care may not reach the clinician's chair because treatment guidelines and payments are set locally. An international symposium to celebrate Mikako Hayashi becoming Professor of Restorative Dentistry and Endodontology at Osaka University concluded that dentistry should move from an increasingly un-affordable curative model to a cost-effective evidence-based preventive model. The goal is to help people retain healthy natural teeth throughout their lives, as an essential part of enhancing their general health. © 2014 FDI World Dental Federation.

Comparative Efficacy of a Soft Toothbrush with Tapered-tip Bristles to an ADA Reference Toothbrush on Gingival Abrasion over a 12-Week Period.

PubMed

Gallob, John; Petrone, Dolores M; Mateo, Luis R; Chaknis, Patricia; Morrison, Boyce M; Panagakos, Foti; Williams, Malcolm

2016-06-01

Evaluation of the impact of a soft toothbrush with tapered-tip (Test Toothbrush) bristles and an ADA reference toothbrush (ADA Toothbrush) on gingival abrasion over a 12-week period. This was a randomized, single-center, examiner-blind, two-cell, parallel clinical research study and used the Danser Gingival Abrasion Index to assess the level of gingival abrasion after a single brushing, as well as after six weeks and 12 weeks of twice-daily brushing. Adult male and female subjects from the Central New Jersey, USA area refrained from all oral hygiene procedures for 24 hours. They reported to the study site after refraining from eating, drinking, and smoking for four hours. Following a qualifying examination using plaque and gingivitis scores along with a baseline gingival abrasion examination, subjects were randomized into two balanced groups, each group using one of the two study toothbrushes. Subjects were instructed to brush their teeth for one minute, under supervision, with their assigned toothbrush and a commercially available fluoride toothpaste (Colgate© Cavity Protection Toothpaste), after which they were again evaluated for gingival abrasion. Subjects were dismissed from the study site with their assigned toothbrush and toothpaste, and instructed to brush twice daily at home for the next 12 weeks. The subjects were instructed to brush for one minute during each tooth brushing. The subjects reported to the study site after six weeks and 12 weeks of product use, at which time they were evaluated for gingival abrasion. Seventy-one (71) subjects complied with the protocol and completed the clinical study. The results of this study showed that the Test Toothbrush provided statistically significantly (p < 0.05) greater reductions in gingival abrasion scores as compared to the gingival abrasion scores of the ADA Toothbrush after a single tooth brushing, after six weeks, and after 12 weeks of product use (75.0%, 85.5%, 73.9%, respectively). The soft toothbrush

The future of dentistry: new challenges, new directions.

PubMed Central

Sinkford, J. C.

1990-01-01

The challenge to our profession today is to improve the quality of oral health while overcoming both extrinsic and intrinsic factors which may adversely affect our progress toward this goal. The combined efforts of dental education, dental research, and dental practice will be needed to enable us to maintain the quality of our present system and to meet the myriad changes that will chart our new directions in the future. Our unified efforts can make a difference and, thereby, ensure a meaningful and productive future for dentistry in our country and throughout the world. Let us show the world that the future of dentistry matters to us and that we look to the future with great anticipation and optimism. PMID:2352286

An abrasion-resistant and broadband antireflective silica coating by block copolymer assisted sol-gel method.

PubMed

Zou, Liping; Li, Xiaoguang; Zhang, Qinghua; Shen, Jun

2014-09-02

A double-layer broadband antireflective (AR) coating was prepared on glass substrate via sol-gel process using two kinds of acid-catalyzed TEOS-derived silica sols. The relative dense layer with a porosity of ∼10% was obtained from an as-prepared sol, while the porous layer with a porosity of ∼55% was from a modified one with block copolymer (BCP) Pluronic F127 as template which results in abundant ordered mesopores. The two layers give rise to a reasonable refractive index gradient from air to the substrate and thus high transmittance in a wide wavelength range, and both of them have the same tough skeleton despite different porosity, for which each single-layer and the double-layer coatings all behaved well in the mechanical property tests. The high transmittance and the strong ability of resisting abrasion make this coating promising for applications in some harsh conditions. In addition, the preparation is simple, low-cost, time-saving, and flexible for realizing the optical property.

Photodetector Development for the Wheel Abrasion Experiment on the Sojourner Microrover of the Mars Pathfinder Mission

NASA Technical Reports Server (NTRS)

Wilt, David M.; Jenkins, Phillip P.; Scheiman, David A.

1997-01-01

On-board the Mars Pathfinder spacecraft, launched in December of 1996, is a small roving vehicle named Sojourner. On Sojourner is an experiment to determine the abrasive characteristics of the Martian surface, called the Wheel Abrasion Experiment (WAE). The experiment works as follows: one of the wheels of the rover has a strip of black anodized aluminum bonded to the tread. The aluminum strip has thin coatings of aluminum, nickel and platinum deposited in patches. There are five (5) patches or samples of each metal, and the patches range in thickness from 200 A to 1000 A. The different metals were chosen for their differing hardness and their environmental stability. As the wheel is spun in the Martian soil, the thin patches of metal are abraded away, exposing the black anodization. The abrasion is monitored by measuring the amount of light reflected off of the samples. A photodetector was developed for this purpose, and that is the subject of this paper.

Postdoctoral Teaching of Geriatric Dentistry in U.S. Dental Schools.

PubMed

Ettinger, Ronald L; Goettsche, Zachary S; Qian, Fang

2017-10-01

The aim of this study was to determine the number and size of postdoctoral teaching programs in geriatric dentistry in U.S. dental schools and other health professions educational institutions and those programs with Health Resources and Services Administration (HRSA) funding. In 2015, all 67 U.S. dental schools were contacted via email with a questionnaire to ask if they had a postdoctoral program in geriatric dentistry; if they did, they were asked to report the length and size of the program. Directors of all 16 HRSA-funded geriatric fellowships were also invited to participate in the survey. Fifty-six of the 67 (83.6%) dental schools and 15 of the 16 (93.8%) HRSA-funded programs completed the questionnaire. Postdoctoral geriatric dentistry programs were reported in 12 dental schools and six medical institutions, although only six programs were currently accepting fellows. The length of the programs was 12-36 months. The maximum number of residents in any program was ten. The oldest program was in Minnesota; it began in 1981. The newest program was beginning in 2017 at Boston University as a revised version of its previous HRSA-funded program. The loss of HRSA funding has had a major negative impact on the number of training programs. Future research is needed to determine how the loss of HRSA-funded programs has affected the availability of educators in geriatric dentistry for dental schools and the services provided to the geriatric community.

The changing public/private mix in dentistry in the UK--a supply-side perspective.

PubMed

Lynch, Mauricea; Calnan, Michael

2003-04-01

This paper examines the factors beyond NHS dentists' remuneration which may explain the variations in the public/private mix in general dental practitioners' workload in the UK. Given that NHS dentistry is subject to a fixed price system, the study focused mainly on non-income supply-side factors. Using data from a postal survey of a national random sample of dentists practising in the NHS in England in 1997, the study found that the strategies adopted by dentists in the management of NHS lists and the evidence that dentists spent significantly more time in private consultations compared with NHS consultations support concerns over equity of access to dental care and the quality of NHS dentistry. Dentists' attitudes to NHS and private dentistry revealed considerable ambiguity towards the NHS. While, on the one hand, the lack of sufficient demand for private dentistry emerged as a strong reason for remaining in the NHS, on the other, there was evidence that equity in access to dental treatment is still seen as an important principle. The implications of these findings in the context of recent discussion of the future of NHS dentistry are considered. Copyright 2002 John Wiley & Sons, Ltd.

[The dentist between medicine and cosmetology. Ethical shortcomings of the esthetics boom in dentistry].

PubMed

Maio, Giovanni

2009-01-01

Dentistry has evolved from a genuine medical practice to a mere business. From an ethical point of view it is asked whether this evolution creates more problems than it solves. The paper elaborates four arguments against this evolution and shows that aesthetics in dentistry which works only according to market categories runs the risk of loosing the view for the real need of patients. Dentistry which comprehends itself as part of a market will be nothing else than a part of a beauty industry which has the only aim to sell something, but not the aim to help people. Such a dentistry makes profit from the ideology of a society which serves only vanity, youthfulness and personal success and which is losing the sight for real values. The real value of man cannot be reduced to his appearance and medicine as an art should feel the obligation to resist these modern ideologies and should help people to get a more authentic attitude to themselves. If modern dentistry fails to think about these implications it will lose its identity as medicine, which would be too great a loss.

Design and evaluation of high-volume fly ash (HVFA) concrete mixes, report D : creep, shrinkage, and abrasion resistance of HVFA concrete.

DOT National Transportation Integrated Search

2012-10-01

The main objective of this study was to determine the effect on shrinkage, creep, : and abrasion resistance of high-volume fly ash (HVFA) concrete. The HVFA concrete : test program consisted of comparing the shrinkage, creep, and abrasion performance...

A laser unit for photodynamic therapy and robot-assisted microsurgery in dentistry

NASA Astrophysics Data System (ADS)

Chunikhin, A. A.; Bazikyan, E. A.; Pikhtin, N. A.

2017-06-01

Results are presented of photochemical experiments with an IR-laser unit for microsurgery and photodynamic therapy in dentistry. The efficiency of direct generation of singlet oxygen in model organic media in the continuous-wave and pulsed nanosecond modes is examined. The unit can serve both as an independent instrument and as a part of a complex for robot-assisted surgery and dentistry.

Comparison of effectiveness of abrasive and enzymatic action of whitening toothpastes in removal of extrinsic stains - a clinical trial.

PubMed

Patil, P A; Ankola, A V; Hebbal, M I; Patil, A C

2015-02-01

To compare the effectiveness of abrasive component (perlite/calcium carbonate) and enzymatic component (papain and bromelain) of whitening toothpaste in removal of extrinsic stains. This study is a randomized, triple blind and parallel group study in which 90 subjects aged 18-40 years were included. At baseline, stains scores were assessed by Macpherson's modification of Lobene Stain Index and subjects were randomly assigned to two groups with 45 subjects in each. Group 1 used whitening toothpaste with enzymatic action and group 2 with abrasive action. After 1 month, stain scores were assessed for the effectiveness of the two toothpastes and 2 months later to check the stain prevention efficacy. Wilcoxson's test was used to compare between baseline 1 and 2 months stain scores, and Mann-Witney U-test was applied for intragroup comparison. The mean baseline total stain score for the subjects allocated to the enzymatic toothpaste was 37.24 ± 2.11 which reduced to 30.77 ± 2.48 in 1 month, and for the abrasive paste, total stain reduced from 35.08 ± 2.96 to 32.89 ± 1.95. The reductions in total stain scores with both the pastes were significant compared with baseline stain scores (at 1 month Group 1, P = 0.0233 and Group 2, P = 0.0324; at 2 months, Group 1 P = 0.0356). Both the toothpastes proved to be equally good in removal of extrinsic stains; however, the enzymatic paste showed better results as compared to abrasive toothpaste. Whitening toothpaste with abrasive action and enzymatic action are equally effective in removal of extrinsic stains; however, whitening toothpaste with abrasive action needs to be used with caution. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Nano Era of Dentistry-An Update.

PubMed

Maman, Paramjot; Nagpal, Manju; Gilhotra, Ritu Mehra; Aggarwal, Geeta

2018-02-14

Management of the health of oral tissues is a prime requirement in dentistry. The prevention of tooth decay and the treatment of lesions and cavities are ongoing challenges. The limitations in dental materials, medications, instruments, procedures put off the accomplishment of this goal. Rationalization of science and technology has made possible to work out these limitations. Nanotechnology which is the outcome of this rationalization has become one of the most favored technologies in medical and dental application. The substantial contribution of nano dental materials is the identification of oral health related problems by better diagnosis and management of dental disorders by bionanomaterials. Application of nanodentistry holds promise for comprehensive dental care by utilizing nanomaterials and ultimately by nanorobots. This review discusses the rationale of nanodentistry, nanocarriers researched in treatment of different dental diseases, the latest innovations in nanomaterials in various disciplines of dentistry; patent literature and related marketed products. Advances in nanotechnology have placed plenty of hopes in terms of improving the oral health care of dental patients. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Neuromuscular dentistry: Occlusal diseases and posture.

PubMed

Khan, Mohd Toseef; Verma, Sanjeev Kumar; Maheshwari, Sandhya; Zahid, Syed Naved; Chaudhary, Prabhat K

2013-01-01

Neuromuscular dentistry has been a controversial topic in the field of dentistry and still remains debatable. The issue of good occlusion and sound health has been repeatedly discussed. Sometimes we get complains of sensitive teeth and sometimes of tired facial muscles on getting up in the morning. Owing to the intimate relation of masticatory apparatus with the cranium and cervico-scapular muscular system, the disorders in any system, draw attention from concerned clinicians involved in management, to develop an integrated treatment protocol for the suffering patients. There may be patients reporting to the dental clinics after an occlusal restoration or extraction, having pain in or around the temporomandibular joint, headache or neck pain. Although their esthetic demands must not be undermined during the course of treatment plan, whenever dental treatment of any sort is planned, occlusion/bite should be given prime importance. Very few dentist are able to diagnose the occlusal disease and of those who diagnose many people resort to aggressive treatment modalities. This paper aims to report the signs of occlusal disease, and discuss their association with TMDs and posture.

The use of information and communication technology (ICT) in dentistry.

PubMed

Knott, N J

2013-02-01

As the use of information and communication technology (ICT) becomes more widespread in dentistry the risk of breaching electronic commerce laws and patient confidentiality increases. It is necessary to be aware of the responsibilities internet usage entails, especially within a dental practice where the protection of patient information is of the utmost importance. More should be done to outline the various precautions that should be taken to ensure ICT security within the professional domain, as it would appear dentistry has been neglected with regard to receiving the proper ICT education, training and support systems.

Evaluation of Tier 5 Medical Training Initiative opportunities in dentistry.

PubMed

Wilson, M A; Burke, M

2012-03-09

This paper reviews the first two years of overseas postgraduate dental placements in the UK under the Medical Training Initiative (MTI), which is part of Tier 5 government authorised exchange. Details of the objectives of the programme, the trainees appointed, specialty areas studied and length of training are described. The methods used for assessing the training are reported. It is concluded that the objectives of the MTI have been met in dentistry and that Tier 5 provides a valuable opportunity for establishing international links in postgraduate clinical dentistry.

Pebble abrasion during fluvial transport: Experimental results and implications for the evolution of the sediment load along rivers

NASA Astrophysics Data System (ADS)

Attal, Mikaël; Lavé, Jérôme

2009-12-01

In actively eroding landscapes, fluvial abrasion modifies the characteristics of the sediment carried by rivers and consequently has a direct impact on the ability of mountain rivers to erode their bedrock and on the characteristics and volume of the sediment exported from upland catchments. In this experimental study, we use a novel flume replicating hydrodynamic conditions prevailing in mountain rivers to investigate the role played by different controlling variables on pebble abrasion during fluvial transport. Lithology controls abrasion rates and processes, with differences in abrasion rates exceeding two orders of magnitude. Attrition as well as breaking and splitting are efficient processes in reducing particle size. Mass loss by attrition increases with particle velocity but is weakly dependent on particle size. Fragment production is enhanced by the use of large particles, high impact velocities and the presence of joints. Based on our experimental results, we extrapolate a preliminary generic relationship between pebble attrition rate and transport stage (τ*/τ*c), where τ* = fluvial Shields stress and τ*c = critical Shields stress for incipient pebble motion. This relationship predicts that attrition rates are independent of transport stage for (τ*/τ*c) ≤ 3 and increase linearly with transport stage beyond this value. We evaluate the extent to which abrasion rates control downstream fining in several different natural settings. A simplified model predicts that the most resistant lithologies control bed load flux and fining ratio and that the concavity of transport-limited river profiles should rarely exceed 0.25 in the absence of deposition and sorting.

Professional ethics and professional etiquette in dentistry: are they compatible?

PubMed

Newbrun, Ernest

2007-01-01

In keeping with the theme of this colloquium, two aspects of ethics in dentistry are addressed: its evolution and its future. With respect to its evolution, two examples of changes in the design of clinical trials in dentistry are discussed. These concern the current requirement of informed consent from the subjects in the trial, now taken for granted, but not necessarily observed before 1964. The Vipeholm dental caries study is one example of pre-Helsinki Declaration experimentation. The second example, also drawn from caries research design, concerns the stricture on the use of placebo-controlled trials in the face of a proven drug. For example, the design of clinical trials of fluoride dentifrices has evolved since the mid 1970s. The use of a placebo-inactive control group is no longer acceptable as it would deprive its subjects of a proven caries-preventive agent and would expose its subjects to increased caries risk. While definitions of professional ethics in dentistry may vary, the ADA Code of Ethics includes five principles: patient autonomy ("self-governance"), non-maleficence ("do no harm"), beneficence ("do good"), justice ("fairness") and veracity ("truthfulness"). Professional etiquette refers to the way dentists relate to one another and is governed by the ADA Code of Professional Conduct which expresses specific types of conduct that are either required or prohibited. Sometimes, ethics and etiquette may conflict. The problem of financial issues that conflict with ethical ones is discussed along with the problem of commercialism in the practice of dentistry. Debts from dental school may adversely affect the professional behavior of young dentists, while general dentists might succumb to "goodies" provided by specialists. These often include continuing education courses, gifts, trips, and kickbacks. Specialists may fail to inform patients of improper or poor quality treatment by the referring general practitioner, fearing loss of referrals. Of course

The economics of dentistry: a neglected concern.

PubMed

Shariati, Batoul; MacEntee, Michael I; Yazdizadeh, Maryam

2013-10-01

Demand for economic evaluations in health care is growing with expectations that they will help to develop regional and national policies on health and social programmes. We present here the scope, quality and content of systematic reviews and meta-analyses relating to the economics of dentistry published over the last 15 years. To review the quality and outcome of systematic reviews and meta-analyses relating to the economics of dental treatments, preventions and services. A systematic search was conducted in 14 electronic databases for systematic reviews and meta-analyses published between January 1997 and July 2011 on the economics of oral disorders and oral health care. Review papers were extracted by two independent investigators to identify the characteristics, results and quality of the reviews and to highlight gaps in knowledge about the economics of dentistry. From 3150 unique references, we found 73 systematic reviews or meta-analyses of dental economics as primary or secondary outcomes. The focus of 12 of them was on the cost or cost-effectiveness of dental prevention, 54 on treatment, five on prevention and treatment and two on delivery of dental services. However, only 12 of the systematic reviews drew conclusions from economic data, and four of them constructed an economic model from synthesized data. Overall, the quality was good in the 12 systematic reviews but poor in the original studies. There is very little helpful data published on the economics of dentistry. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Recent advancements in regenerative dentistry: A review.

PubMed

Amrollahi, Pouya; Shah, Brinda; Seifi, Amir; Tayebi, Lobat

2016-12-01

Although human mouth benefits from remarkable mechanical properties, it is very susceptible to traumatic damages, exposure to microbial attacks, and congenital maladies. Since the human dentition plays a crucial role in mastication, phonation and esthetics, finding promising and more efficient strategies to reestablish its functionality in the event of disruption has been important. Dating back to antiquity, conventional dentistry has been offering evacuation, restoration, and replacement of the diseased dental tissue. However, due to the limited ability and short lifespan of traditional restorative solutions, scientists have taken advantage of current advancements in medicine to create better solutions for the oral health field and have coined it "regenerative dentistry." This new field takes advantage of the recent innovations in stem cell research, cellular and molecular biology, tissue engineering, and materials science etc. In this review, the recently known resources and approaches used for regeneration of dental and oral tissues were evaluated using the databases of Scopus and Web of Science. Scientists have used a wide range of biomaterials and scaffolds (artificial and natural), genes (with viral and non-viral vectors), stem cells (isolated from deciduous teeth, dental pulp, periodontal ligament, adipose tissue, salivary glands, and dental follicle) and growth factors (used for stimulating cell differentiation) in order to apply tissue engineering approaches to dentistry. Although they have been successful in preclinical and clinical partial regeneration of dental tissues, whole-tooth engineering still seems to be far-fetched, unless certain shortcomings are addressed. Copyright © 2016 Elsevier B.V. All rights reserved.

Digital photoelastic analysis applied to implant dentistry

NASA Astrophysics Data System (ADS)

Ramesh, K.; Hariprasad, M. P.; Bhuvanewari, S.

2016-12-01

Development of improved designs of implant systems in dentistry have necessitated the study of stress fields in the implant regions of the mandible/maxilla for better understanding of the biomechanics involved. Photoelasticity has been used for various studies related to dental implants in view of whole field visualization of maximum shear stress in the form of isochromatic contours. The potential of digital photoelasticity has not been fully exploited in the field of implant dentistry. In this paper, the fringe field in the vicinity of the connected implants (All-On-Four® concept) is analyzed using recent advances in digital photoelasticity. Initially, a novel 3-D photoelastic model making procedure, to closely mimic all the anatomical features of the human mandible is proposed. By choosing appropriate orientation of the model with respect to the light path, the essential region of interest were sought to be analysed while keeping the model under live loading conditions. Need for a sophisticated software module to carefully identify the model domain has been brought out. For data extraction, five-step method is used and isochromatics are evaluated by twelve fringe photoelasticity. In addition to the isochromatic fringe field, whole field isoclinic data is also obtained for the first time in implant dentistry, which could throw important information in improving the structural stability of the implant systems. Analysis is carried out for the implant in the molar as well as the incisor region. In addition, the interaction effects of loaded molar implant on the incisor area are also studied.

Universal adhesives: the next evolution in adhesive dentistry?

PubMed

Alex, Gary

2015-01-01

Every so often a new material, technique, or technological breakthrough spurs a paradigm shift in the way dentistry is practiced. The development and evolution of reliable enamel and dentin bonding agents is one such example. Indeed, the so-called "cosmetic revolution" in dentistry blossomed in large part due to dramatic advances in adhesive technology. It is the ability to bond various materials in a reasonably predictable fashion to both enamel and dentin substrates that enables dentists to routinely place porcelain veneers, direct and indirect composites, and a plethora of other restorative and esthetic materials. In fact, the longevity and predictability of many (if not most) current restorative procedures is wholly predicated on the dentist's ability to bond various materials to tooth tissues. Adhesive systems have progressed from the largely ineffective systems of the 1970s and early 1980s to the relatively successful total- and self-etching systems of today. The latest players in the adhesive marketplace are the so-called "universal adhesives." In theory, these systems have the potential to significantly simplify and expedite adhesive protocols and may indeed represent the next evolution in adhesive dentistry. But what defines a universal system, and are all these new systems truly "universal" and everything they are claimed to be? This article will examine the origin, chemistry, strengths, weaknesses, and clinical relevance of this new genre of dental adhesives.

Evaluation of the Effectiveness of Wet Blast Cleaning Methods of Surface Preparation

DTIC Science & Technology

1985-06-01

for Air Abrasive Wet Blast: Complete System Water Abrasive Mixing Chamber in Slurry Blast Unit Schematic of unit Control Unit Slurry Blast — Air/Water...this discussion we present some general. user guidelines regarding what to look for in con- sidering the use or purchase of wet blasting equipment...These units use compressed air as the medium to propel the eroding material. They differ from air abrasive wet blast units in that the abrasive is mixed

The efficacy of a highly concentrated fluoride dentifrice on bovine enamel subjected to erosion and abrasion.

PubMed

Rios, Daniela; Magalhães, Ana Carolina; Polo, Renata Ocon Braga; Wiegand, Annette; Attin, Thomas; Buzalaf, Marilia Afonso Rabelo

2008-12-01

Researchers have proposed the use of fluoride for the prevention of enamel wear; however, only limited information is available about the impact of fluoridated dentifrices. Because tooth wear is a well-recognized dental problem, the authors conducted an in situ, ex vivo study to assess the efficacy of a highly concentrated fluoride dentifrice on bovine enamel subjected to erosion and abrasion. The authors conducted a double-blind, crossover in situ study consisting of three phases (seven days each). In each phase, the authors tested one of the dentifrices (5,000 parts per million fluoride [F]; 1,100 ppm F; no F). They performed erosive challenges with the use of cola drink (60 seconds, four times per day) and abrasive challenges via toothbrushing (30 seconds, four times per day). The authors determined the enamel loss via profilometry. The authors tested the data by using two-way analysis of variance (P < .05). For the erosion-plus-abrasion condition, the study results showed that enamel wear was significantly higher than that with erosion alone. The findings showed no significant differences between the dentifrices regarding enamel wear. Within the in situ, ex vivo conditions of this study, the authors concluded that the highly concentrated fluoride dentifrice did not have a protective effect on enamel against erosion and erosion plus toothbrushing abrasion. Patients at risk of developing enamel erosion should benefit from preventive measures other than fluoride dentifrice, because even a highly concentrated fluoride dentifrice does not appear to prevent enamel erosion.

Potent Inhalational Anesthetics for Dentistry

PubMed Central

Satuito, Mary; Tom, James

2016-01-01

Nitrous oxide and the volatile inhalational anesthetics have defined anxiety and pain control in both dentistry and medicine for over a century. From curious experimentation to spectacular public demonstrations, the initial work of 2 dentists, Horace Wells and William T. G. Morton, persists to this day in modern surgery and anesthesia. This article reviews the history, similarities, differences, and clinical applications of the most popular inhalational agents used in contemporary dental surgical settings. PMID:26866411

Casing window milling with abrasive fluid jet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vestavik, O.M.; Fidtje, T.H.; Faure, A.M.

1995-12-31

Methods for through tubing re-entry drilling of multilateral wells has a large potential for increasing hydrocarbon production and total recovery. One of the bottle-necks of this technology is initiation of the side-track by milling a window in the casing downhole. A new approach to this problem has been investigated in a joint industry project. An experimental set-up has been built for milling a 4 inch window in a 7 inch steel casing at surface in the laboratory. A specially designed bit developed at RIF using abrasive jet cutting technology has been used for the window milling. The bit has anmore » abrasive jet beam which is always directed in the desired side-track direction, even if the bit is rotating uniformly. The bit performs the milling with a combined mechanical and hydraulic jet action. The method has been successfully demonstrated. The experiments has shown that the window milling can be performed with very low WOB and torque, and that only small side forces are required to perform the operation. Casing milling has been performed without a whipstock, a cement plug has been the only support for the tool. The tests indicate that milling operations can be performed more efficiently with less time and costs than what is required with conventional techniques. However, the method still needs some development of the downhole motor for coiled tubing applications. The method can be used both for milling and drilling giving the advantage of improved rate of penetration, improved bit life and increased horizontal reach. The method is planned to be demonstrated downhole in the near future.« less

The safety of bone allografts used in dentistry: a review.

PubMed

Holtzclaw, Dan; Toscano, Nicholas; Eisenlohr, Lisa; Callan, Don

2008-09-01

Recent media reports concerning "stolen body parts" have shaken the public's trust in the safety of and the use of ethical practices involving human allografts. The authors provide a comprehensive review of the safety aspects of human bone allografts. The authors reviewed U.S. government regulations, industry standards, independent industry association guidelines, company guidelines and scientific articles related to the use of human bone allografts in the practice of dentistry published in the English language. The use of human bone allografts in the practice of dentistry involves the steps of procurement, processing, use and tracking. Rigorous donor screening and aseptic proprietary processing programs have rendered the use of human bone allografts safe and effective as a treatment option. When purchasing human bone allografts for the practice of dentistry, one should choose products accredited by the American Association of Tissue Banks for meeting uniformly high safety and quality control measures. Knowledge of human bone allograft procurement, processing, use and tracking procedures may allow dental clinicians to better educate their patients and address concerns about this valuable treatment option.

Curriculum emphasis and resident preparation in postgraduate general dentistry programs.

PubMed

Lefever, Karen H; Atchison, Kathryn A; Mito, Ronald S; Lin, Sylvia

2002-06-01

In 1999 HRSA contracted with the UCLA School of Dentistry to evaluate the impact of federal funding on postgraduate general dentistry programs. Part of that evaluation analyzed curriculum emphasis and preparation of incoming residents in advanced general dentistry programs over a five-year period. Directors of 208 civilian AEGD and GPR programs were surveyed about the curriculum content of their programs, increased or decreased emphasis in thirty subject areas, and resident preparation and quality (GPA and National Board scores). Results indicate that curriculum changes in AEGD and GPR programs over the time period have been responsive to the changing nature of general practice. At least half of all program directors reported that their residents were less than adequately prepared in fourteen curriculum areas. Sub-analyses were conducted for AEGD/GPR programs and HRSA-funded versus nonfunded programs. Multivariate regression identified lower student quality as the most important program variable in predicting a perceived need for resident remediation. Logistic regression showed that programs with higher resident GPA and National Board Part I scores had less difficulty filling resident positions.

Self-healing of the superhydrophobicity by ironing for the abrasion durable superhydrophobic cotton fabrics

PubMed Central

Wu, Jingxia; Li, Jingye; Deng, Bo; Jiang, Haiqing; Wang, Ziqiang; Yu, Ming; Li, Linfan; Xing, Chenyang; Li, Yongjin

2013-01-01

Self-healing of the superhydrophobic cotton fabric (SCF) obtained by the radiation-induced graft polymerization of lauryl methacrylate (LMA) and n-hexyl methacrylate (HMA), can be achieved by ironing. Through the steam ironing process, the superhydrophobicity of the SCFs will be regenerated even after the yarns are ruptured during the abrasion test under a load pressure of 44.8 kPa. SCFs made from LMA grafted cotton fabric can ultimately withstand at least 24,000 cycles of abrasion with periodic steam ironing. The FT-IR microscope results show that the migration of the polymethacrylates graft chains from the interior to the surface is responsible for the self-healing effect. PMID:24135813

Degradation of the Crystalline Structure of ZnS Ceramics under Abrasive Damage

NASA Astrophysics Data System (ADS)

Shcherbakov, I. P.; Dunaev, A. A.; Chmel, A. E.

2018-04-01

Stability of optical elements based on ZnS ceramics to dust and rain erosion is usually estimated from the loss of material mass in a directional flow of solid particles or atmospheric precipitates. In this case, the mechanism of degradation and fracture of the surface layer of an optical element is not considered. The photoluminescence (PL) method was used for investigating the crystal lattice response to the abrasive action and the formation of cleavage in ZnS ceramics, which differ in manufacturing technology and, accordingly, in the grain size by two orders of magnitude. It is shown that during abrasive treatment of samples, their spectra exhibit changes typical of degradation of the crystal lattice of material grains. The PL spectra of cleavage surfaces reveal almost complete degradation of the structure of crystallite grains with a size from 1-2 to 100-200 μm.

Consensus Conference Findings on Supragingival and Subgingival Air Polishing.

PubMed

Cobb, Charles M; Daubert, Diane M; Davis, Karen; Deming, Jodi; Flemmig, Thomas F; Pattison, Anna; Roulet, Jean-François; Stambaugh, Roger V

2017-02-01

A consensus conference was convened to evaluate and address issues of safety and efficacy when using glycine powder in an air-powder jet device for supra- and subgingival applications during dental prophylaxis and periodontal maintenance. The conference reported the following conclusions: 1) Supra- and subgingival air polishing using glycine powder is safe and effective for removal of biofilms from natural tooth structure and restorative materials; 2) there is no evidence of soft-tissue abrasion when using glycine powder in an air-polishing device; 3) in periodontal probing depths of 1 mm to 4 mm, glycine-powder air polishing, using a standard air-polishing nozzle, is more effective at removing subgingival biofilm than manual or ultrasonic instruments; and 4) at probing depths of 5 mm to 9 mm, using a subgingival nozzle, glycine powder air polishing is more effective at removing subgingival biofilm than manual or ultrasonic instrumentation. This conference statement, supported by an industry grant, was drafted by a panel of distinguished dental professionals.

Organized dentistry as an agent for helping others: the leadership of Donna J. Rumberger.

PubMed

Rule, James T; Bebeau, Muriel J

2003-09-01

Dr Donna Rumberger graduated from New York University College of Dentistry in 1980 and has practiced dentistry in Manhattan ever since. Even before her graduation, she was active in organized dentistry, always viewing it as a conduit for helping other people. Working with the American Association of Women Dentists, she was cofounder of the Smiles for Success Foundation, a program started in New York City that helps women advance from welfare into the workforce with restored, healthy smiles. That program now has expanded to 14 other cities. Working with organized dentistry in New York City, she has been instrumental in initiating and running the Skate Safe program, which provides mouthguards and oral home care education for inner city children in Harlem. In addition, she has worked with the dentistry merit badge program for the Boy Scouts of America Jamborees, helped coalesce women's dental organizations in New York City, and led her dental society to collaborate with Columbia University in a program to improve access to dental care. As further evidence of her ability to get things done, she also has served as president of the American Association of Women Dentists, the Midtown Dental Society, and the New York County Dental Society--one of the largest dental societies in the country.

Nanotechnology in dentistry: prevention, diagnosis, and therapy.

PubMed

Abou Neel, Ensanya Ali; Bozec, Laurent; Perez, Roman A; Kim, Hae-Won; Knowles, Jonathan C

2015-01-01

Nanotechnology has rapidly expanded into all areas of science; it offers significant alternative ways to solve scientific and medical questions and problems. In dentistry, nanotechnology has been exploited in the development of restorative materials with some significant success. This review discusses nanointerfaces that could compromise the longevity of dental restorations, and how nanotechnolgy has been employed to modify them for providing long-term successful restorations. It also focuses on some challenging areas in dentistry, eg, oral biofilm and cancers, and how nanotechnology overcomes these challenges. The recent advances in nanodentistry and innovations in oral health-related diagnostic, preventive, and therapeutic methods required to maintain and obtain perfect oral health, have been discussed. The recent advances in nanotechnology could hold promise in bringing a paradigm shift in dental field. Although there are numerous complex therapies being developed to treat many diseases, their clinical use requires careful consideration of the expense of synthesis and implementation.

Nanotechnology in dentistry: prevention, diagnosis, and therapy

PubMed Central

Abou Neel, Ensanya Ali; Bozec, Laurent; Perez, Roman A; Kim, Hae-Won; Knowles, Jonathan C

2015-01-01

Nanotechnology has rapidly expanded into all areas of science; it offers significant alternative ways to solve scientific and medical questions and problems. In dentistry, nanotechnology has been exploited in the development of restorative materials with some significant success. This review discusses nanointerfaces that could compromise the longevity of dental restorations, and how nanotechnolgy has been employed to modify them for providing long-term successful restorations. It also focuses on some challenging areas in dentistry, eg, oral biofilm and cancers, and how nanotechnology overcomes these challenges. The recent advances in nanodentistry and innovations in oral health-related diagnostic, preventive, and therapeutic methods required to maintain and obtain perfect oral health, have been discussed. The recent advances in nanotechnology could hold promise in bringing a paradigm shift in dental field. Although there are numerous complex therapies being developed to treat many diseases, their clinical use requires careful consideration of the expense of synthesis and implementation. PMID:26504385

Gene Therapy: A Paradigm Shift in Dentistry

PubMed Central

Siddique, Nida; Raza, Hira; Ahmed, Sehrish; Khurshid, Zohaib; Zafar, Muhammad Sohail

2016-01-01

Gene therapy holds a promising future for bridging the gap between the disciplines of medicine and clinical dentistry. The dynamic treatment approaches of gene therapy have been advancing by leaps and bounds. They are transforming the conventional approaches into more precise and preventive ones that may limit the need of using drugs and surgery. The oral cavity is one of the most accessible areas for the clinical applications of gene therapy for various oral tissues. The idea of genetic engineering has become more exciting due to its advantages over other treatment modalities. For instance, the body is neither subjected to an invasive surgery nor deep wounds, nor is it susceptible to systemic effects of drugs. The aim of this article is to review the gene therapy applications in the field of dentistry. In addition, therapeutic benefits in terms of treatment of diseases, minimal invasion and maximum outcomes have been discussed. PMID:27834914

Direct reimbursement. The future for organized dentistry.

PubMed

Paul, D P

2001-10-01

Direct reimbursement, or DR, has been a popular topic in organized dentistry for much of the last decade, and the concept is beginning to be more widely known. This article explores the underpinnings of and future for DR. TYPES OF LITERATURE REVIEWED: This article is based on an online review of the dental, medical and business literature. The author explores the advantages of DR for patients, employers and dentists. He also presents purported disadvantages of DR, and refutes them. Organized dentistry's marketing efforts and the importance of third-party administrators also are examined. During the next several years, DR has the potential to become the vehicle of choice for financing much of the dental care provided in the United States. Dentists need to become more aware of what DR is and what it can offer the public. They then will be better able to promote DR, which is a significantly better payment system for dental care than any other available today.

Effects of an Air-Powder Abrasive Device When Used during Periodontal Flap Surgery in Dogs.

DTIC Science & Technology

1983-01-01

instru- ments, ultrasonic devices, air driven reciprocating hand- pieces, and air driven rotary handpieces (Schaffer, 1967). None of these techniques...system, the Prophy-Jet Mark IV C-100 , may be an alternative to conventional mechanical and chemical methods of detoxifying roots. The handpiece is...electric current and uses inlet air pressure of 65 to 100 p.s.i. and inlet water pressure of 25 to 60 p.s.i. The handpiece propels particles of the

Antibacterial activity in adhesive dentistry: a literature review.

PubMed

Shafiei, Fereshteh; Memarpour, Mahtab

2012-01-01

This literature review summarizes the published research regarding the antibacterial agents used in adhesive dentistry. This article provides information about the clinical applications, beneficial effects, and possible disadvantages of antibacterials when used in various bonding situations.

Platelet recruitment promotes keratocyte repopulation following corneal epithelial abrasion in the mouse

USDA-ARS?s Scientific Manuscript database

Corneal abrasion not only damages the epithelium but also induces stromal keratocyte death at the site of injury. While a coordinated cascade of inflammatory cell recruitment facilitates epithelial restoration, it is unclear if this cascade is necessary for keratocyte recovery. Since platelet and ne...

Synthetic optimization of air turbine for dental handpieces.

PubMed

Shi, Z Y; Dong, T

2014-01-01

A synthetic optimization of Pelton air turbine in dental handpieces concerning the power output, compressed air consumption and rotation speed in the mean time is implemented by employing a standard design procedure and variable limitation from practical dentistry. The Pareto optimal solution sets acquired by using the Normalized Normal Constraint method are mainly comprised of two piecewise continuous parts. On the Pareto frontier, the supply air stagnation pressure stalls at the lower boundary of the design space, the rotation speed is a constant value within the recommended range from literature, the blade tip clearance insensitive to while the nozzle radius increases with power output and mass flow rate of compressed air to which the residual geometric dimensions are showing an opposite trend within their respective "pieces" compared to the nozzle radius.

An Assessment of the Risk of Bias in Randomized Controlled Trial Reports Published in Prosthodontic and Implant Dentistry Journals.

PubMed

Papageorgiou, Spyridon N; Kloukos, Dimitrios; Petridis, Haralampos; Pandis, Nikolaos

2015-01-01

The objective of this study was to assess the risk of bias of randomized controlled trials (RCTs) published in prosthodontic and implant dentistry journals. The last 30 issues of 9 journals in the field of prosthodontic and implant dentistry (Clinical Implant Dentistry and Related Research, Clinical Oral Implants Research, Implant Dentistry, International Journal of Oral & Maxillofacial Implants, International Journal of Periodontics and Restorative Dentistry, International Journal of Prosthodontics, Journal of Dentistry, Journal of Oral Rehabilitation, and Journal of Prosthetic Dentistry) were hand-searched for RCTs. Risk of bias was assessed using the Cochrane Collaboration's risk of bias tool and analyzed descriptively. From the 3,667 articles screened, a total of 147 RCTs were identified and included. The number of published RCTs increased with time. The overall distribution of a high risk of bias assessment varied across the domains of the Cochrane risk of bias tool: 8% for random sequence generation, 18% for allocation concealment, 41% for masking, 47% for blinding of outcome assessment, 7% for incomplete outcome data, 12% for selective reporting, and 41% for other biases. The distribution of high risk of bias for RCTs published in the selected prosthodontic and implant dentistry journals varied among journals and ranged from 8% to 47%, which can be considered as substantial.

Simplified Abrasion Test Methodology for Candidate EVA Glove Lay-Ups

NASA Technical Reports Server (NTRS)

Rabel, Emily; Aitchison, Lindsay

2015-01-01

During the Apollo Program, space suit outer-layer fabrics were badly abraded after performing just a few extravehicular activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots that penetrated the outer-layer fabric into the thermal protection layers after less than 8 hrs of surface operations. Current plans for the exploration planetary space suits require the space suits to support hundreds of hours of EVA on a lunar or Martian surface, creating a challenge for space suit designers to utilize materials advances made over the last 40 years and improve on the space suit fabrics used in the Apollo Program. Over the past 25 years the NASA Johnson Space Center Crew and Thermal Systems Division has focused on tumble testing as means of simulating wear on the outer layer of the space suit fabric. Most recently, in 2009, testing was performed on 4 different candidate outer layers to gather baseline data for future use in design of planetary space suit outer layers. In support of the High Performance EVA Glove Element of the Next Generation Life Support Project, testing a new configuration was recently attempted in which require 10% of the fabric per replicate of that need in 2009. The smaller fabric samples allowed for reduced per sample cost and flexibility to test small samples from manufacturers without the overhead to have a production run completed. Data collected from this iteration was compared to that taken in 2009 to validate the new test method. In addition the method also evaluated the fabrics and fabric layups used in a prototype thermal micrometeoroid garment (TMG) developed for EVA gloves under the NASA High Performance EVA Glove Project. This paper provides a review of previous abrasion studies on space suit fabrics, details methodologies used for abrasion testing in this particular study, results of the validation study, and results of the TMG testing.

The slope and incision length of affected local cross abrasion and accretion using ASTER GDEM image analysis

NASA Astrophysics Data System (ADS)

Anugrahadi, A.

2018-01-01

Remote sensing technology is to support the identification and assessment of resources and disasters in coastal areas and oceans, because it has the advantage of covering large areas and the highest of the spatial and temporal resolution. Aster GDEM image is used to determine the slope and the length of cross the incision on exposed area abrasion and accretion. Western coastal of Banten Province has experienced abrasion with the furthest distance of 125.05 m to 274.73 m. and experienced accretion with the furthest distance of 31.65 m to 111, 58 m. ASTER GDEM results of image analysis in areas of abrasion has a slope about 1.4° to 3.3° and cross the incision length is approximately 350.52 meters to 506.57 meters. At the accretion region has a slope about 2.0° to 3.1° and cross the incision length about 306.62 m to 562.05 m.

“Evidence-Based Dentistry in Oral Surgery: Could We Do Better?”

PubMed Central

Nocini, Pier Francesco; Verlato, Giuseppe; Frustaci, Andrea; de Gemmis, Antonio; Rigoni, Giovanni; De Santis, Daniele

2010-01-01

Evidence-based Dentistry (EBD), like Evidence-based Medicine (EBM), was born in order to seek the “best available research evidence” in the field of dentistry both in research and clinical routine. But evidence is not clearly measurable in all fields of healthcare: in particular, while drug effect is rather independent from clinician’s characteristics, the effectiveness of surgical procedures is strictly related to surgeon’s expertise, which is difficult to quantify. The research problems of dentistry have a lot in common with other surgical fields, where at the moment the best therapeutic recommendations and guidelines originates from an integration of evidence-based medicine and data from consensus conferences. To cope with these problems, new instruments have been developed, aimed at standardizing clinical procedures (CAD-CAM technology) and at integrating EBM achievements with the opinions of expert clinicians (GRADE System). One thing we have to remember however: it is necessary to use the instruments developed by evidence-based medicine but is impossible to produce sound knowledge without considering clinical expertise and quality of surgical procedures simultaneously. Only in this way we will obtain an evidence-based dentistry both in dental research and clinical practice, which is up to third millennium standards. PMID:20871758

Public perception of cross-infection control in dentistry.

PubMed

Thomson, W M; Stewart, J F; Carter, K D; Spencer, A J

1997-10-01

Since the advent of HIV/AIDS at the beginning of the 1980s, concern has generated considerable impetus for change in cross-infection control procedures in dentistry. This process has been hastened partly by media coverage which, in tending to favour sensation over rational discourse, has played a not inconsiderable role in shaping public understanding and expectations. This study aimed to investigate public perceptions of cross-infection control in dentistry in Australia using a postal follow-up to the 1995 National Dental Telephone Interview Survey. The postal survey response rate was 85.2 per cent. Concerns about the procedures used by their dentist to sterilize instruments were reported by 13.3 per cent of respondents overall, and this was greater among non-health-card-holders, individuals who mainly spoke a language other than English in the home, and those who reported a non-routine dental visiting pattern. Avoidance or delaying of dental visits due to the perceived cross-infection risk was reported by an overall 3.6 per cent of people, and this was higher among females and those who expressed concern about cross-infection control. The profession has a responsibility to ensure that information on the measures which have been taken to reduce the risk of cross-infection in dentistry is disseminated as widely and as clearly as possible so that undue public concern and avoidance of dental care are minimized.

Assessment of the influence of vegetarian diet on the occurrence of erosive and abrasive cavities in hard tooth tissues.

PubMed

Herman, Katarzyna; Czajczyńska-Waszkiewicz, Agnieszka; Kowalczyk-Zając, Małgorzata; Dobrzyński, Maciej

2011-11-25

The aim of the study was to determine the potential relation between vegetarian diet and tooth erosion and abrasion. The examination included 46 vegetarians and the same number in the control group. Clinical research was carried out in order to detect the presence of abrasive and erosive changes and the level of hygiene in oral cavities. The questionnaire survey concerned dietary and hygienic habits. Statistical analysis of the data was conducted with Chi-square test and Mann-Whitney U test. The relations between following a vegetarian diet and the occurrence of non-carious cavities was tested with models of logistic regression. Tooth erosion was present among 39.1% of vegetarians and 23.9% of controls, while abrasion appeared among 26.1% and 10.9%, respectively, and the differences were statistically insignificant. The distribution of the changes was similar in both groups. Among vegetarians, significantly more frequent consumption of sour products (predominantly raw vegetables and fruit and tomatoes) was observed. The level of oral hygiene and hygienic habits were similar in both groups. The analysis of statistical regression did not reveal any relations between following a vegetarian diet and the occurrence of tooth erosion and abrasion. The results did not reveal any direct influence of vegetarian diet on the occurrence of erosive and abrasive changes. However, in the vegetarian group, more frequent consumption of some sour products and more commonly used horizontal brushing method were observed, with a slightly higher occurrence of non-carious cavities. Further research is required to obtain unambiguous conclusions.

Zircon geochronology and ca. 400 Ma exhumation of Norwegian ultrahigh-pressure rocks: An ion microprobe and chemical abrasion study

USGS Publications Warehouse

Root, D.B.; Hacker, B.R.; Mattinson, J.M.; Wooden, J.L.

2004-01-01

Understanding the formation and exhumation of the remarkable ultrahigh-pressure (UHP) rocks of the Western Gneiss Region, Norway, hinges on precise determination of the time of eclogite recrystallization. We conducted detailed thermal ionization mass spectrometry, chemical abrasion analysis and sensitive high-resolution ion-microprobe analysis of zircons from four ultrahigh- and high-pressure (HP) rocks. Ion-microprobe analyses from the Flatraket eclogite yielded a broad range of apparently concordant Caledonian ages, suggesting long-term growth. In contrast, higher precision thermal ionization mass spectrometry analysis of zircon subject to combined thermal annealing and multi-step chemical abrasion yielded moderate Pb loss from the first (lowest temperature) abrasion step, possible minor Pb loss or minor growth at 400 Ma from the second step and a 407-404 Ma cluster of slightly discordant 206Pb/238U ages, most likely free from Pb loss, from the remaining abrasion steps. We interpret the latter to reflect zircon crystallization at ???405-400 Ma with minor discordance from inherited cores. Zircon crystallization occurred at eclogite-facies, possibly post-peak conditions, based on compositions of garnet inclusions in zircon as well as nearly flat HREE profiles and lack of Eu anomalies in zircon fractions subjected to chemical abrasion. These ages are significantly younger than the 425 Ma age often cited for western Norway eclogite recrystallization, implying faster rates of exhumation (>2.5-8.5 km/Myr), and coeval formation of eclogites across the UHP portion of the Western Gneiss Region. ?? 2004 Published by Elsevier B.V.

Regenerative dentistry: translating advancements in basic science research to the dental practice.

PubMed

Garcia-Godoy, Franklin; Murray, Peter

2010-01-01

Scientific advances in the creation of restorative biomaterials, in vitro cell culture technology, tissue engineering, molecular biology and the human genome project provide the basis for the introduction of new technologies into dentistry. This review provides an assessment of how tissue engineering, stem cell, genetic transfer, biomaterial and growth factor therapies can be integrated into clinical dental therapies to restore and regenerate oral tissues. In parallel to the creation of a new field in general medicine called "regenerative medicine," we call this field "regenerative dentistry." While the problems of introducing regenerative therapies are substantial, the potential benefits to patients and the profession are equally ground-breaking. In this review, we outline a few areas of interest for the future of oral and dental medicine in which advancements in basic science have already been adapted to fit the goals of 21st century dentistry.

Hypoxia-based strategies for regenerative dentistry-Views from the different dental fields.

PubMed

Müller, Anna Sonja; Janjić, Klara; Lilaj, Bledar; Edelmayer, Michael; Agis, Hermann

2017-09-01

The understanding of the cell biological processes underlying development and regeneration of oral tissues leads to novel regenerative approaches. Over the past years, knowledge on key roles of the hypoxia-based response has become more profound. Based on these findings, novel regenerative approaches for dentistry are emerging, which target cellular oxygen sensors. These approaches include hypoxia pre-conditioning and pharmacologically simulated hypoxia. The increase in studies on hypoxia and hypoxia-based strategies in regenerative dentistry highlights the growing attention to hypoxia's role in regeneration and its underlying biology, as well as its application in a therapeutic setting. In this narrative review, we present the current knowledge on the role of hypoxia in oral tissues and review the proposed hypoxia-based approaches in different fields of dentistry, including endodontics, orthodontics, periodontics, and oral surgery. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Prevention of spinal disorders in dentistry].

PubMed

Iordache, Cristina; Scutariu, Monica; Ancuţa, Codrina

2010-01-01

Professional activity in dentistry account for excessive request of the spine and peripheral joints. We performed an observational prospective study on ten physicians (six women, four men) aiming to evaluate the time used in vicious positions during a working day and to establish a specific kinetic program directed to relaxation and rebalancing lumbo-abdomino-pelvic muscles. The working time in a typical day either using orthostatic or sitting position was assessed according to a standard protocol. Left dorsal scoliosis with rotation lasting over 97 minutes of daily working time, sinistro-concave dorsal scoliosis with a typical duration of 42.5 minutes, dextro-concave kyphoscoliosis with a mean time of 37 minutes and dorsal scoliosis with right rotation lasting 31 minutes were reported. Moreover, both left and right rotations were demonstrated during the working time accounting for about 22.5 minutes and 29 minutes respectively, while a lesser time deal with the side of right-left uncombined movement. Almost three quarters of working time (71%) takes place in vicious positions, suggesting that, unfortunately, the ergonomic position is seldom maintained in current dentistry practice. A complex rehabilitation program is therefore mandatory in order to prevent muscle imbalance.

Neuromuscular dentistry: Occlusal diseases and posture

PubMed Central

Khan, Mohd Toseef; Verma, Sanjeev Kumar; Maheshwari, Sandhya; Zahid, Syed Naved; Chaudhary, Prabhat K.

2013-01-01

Neuromuscular dentistry has been a controversial topic in the field of dentistry and still remains debatable. The issue of good occlusion and sound health has been repeatedly discussed. Sometimes we get complains of sensitive teeth and sometimes of tired facial muscles on getting up in the morning. Owing to the intimate relation of masticatory apparatus with the cranium and cervico-scapular muscular system, the disorders in any system, draw attention from concerned clinicians involved in management, to develop an integrated treatment protocol for the suffering patients. There may be patients reporting to the dental clinics after an occlusal restoration or extraction, having pain in or around the temporomandibular joint, headache or neck pain. Although their esthetic demands must not be undermined during the course of treatment plan, whenever dental treatment of any sort is planned, occlusion/bite should be given prime importance. Very few dentist are able to diagnose the occlusal disease and of those who diagnose many people resort to aggressive treatment modalities. This paper aims to report the signs of occlusal disease, and discuss their association with TMDs and posture. PMID:25737904

Cross-infection risks associated with current procedures for using high-speed dental handpieces.

PubMed Central

Lewis, D L; Boe, R K

1992-01-01

When a dye solution used to simulate patient material was either injected into high-speed dental handpiece (drill) waterlines or applied to the equipment externally, internal air turbine chambers became contaminated. These chambers served as a reservoir of the material, which was slowly dislodged by air expelled during subsequent handpiece operation and which was diluted by water spray used for cooling the drilling surface. Considering the fact that patient materials could reside in internal parts of the equipment that are not usually disinfected and that the material may be subsequently sprayed into cuts and abrasions in the oral cavity, the common approach to reprocessing handpieces (external wiping in combination with flushing) may pose unacceptably high risks to those individuals treated soon after infected patients. Therefore, unless reliable data on cross-infection frequencies are obtained and prove it unnecessary, heat-treating high-speed handpieces between each patient should be considered an essential component of standard procedures whenever universal precautions are practiced in dentistry. PMID:1537909

Social Sciences and Dentistry: A Critical Bibliography.

ERIC Educational Resources Information Center

Richards, N. David, Ed.; Cohen Lois K., Ed.

This bibliographic review of social sciences studies in the field of dentistry is a result of the collaboration of dentists and social and behavioral scientists who volunteered manuscripts to the Commission on Dental Practice of the Federation Dentaire Internationale. The manuscript topics include: (1) social science research on the dental…

Early dental journalism: a mirror of the development of dentistry as a profession.

PubMed Central

Hook, S A

1985-01-01

The rise of dentistry from a mechanical trade to a profession has often been attributed to the so-called "triumvirate" of organization, education, and journal literature. This essay focuses on one part of the triumvirate, examining the role of journals in the growth of dentistry as a profession, from the appearance of the first journal in 1839 to the publication of the Index to Dental Literature in 1921. Rather than discussing the history of individual titles, it identifies some of the broader issues and problems that confronted early dental journalism. The evolution of dental journals from trade house publications to independent scientific literature mirrored the movement toward professional status in dentistry during the late 19th and early 20th centuries. PMID:3902129

Laser therapy on points of acupuncture: Are there benefits in dentistry?

PubMed

de Oliveira, Renata Ferreira; da Silva, Camila Vieira; Cersosimo, Maria Cecília Pereira; Borsatto, Maria Cristina; de Freitas, Patrícia Moreira

2015-10-01

Studies have shown the use of laser therapy at points of acupuncture as an alternative to metal needles. The scientific literature in the area of laser acupuncture is rather large; however, the actual mechanisms and effects have not yet been proven in detail. Therefore, the current manuscript reviews the existing literature regarding the effects of laser acupuncture in Dentistry, seeking treatment modalities in which this technique is used and which are able to generate positive clinical results. Thus, the literature survey was conducted in electronic databases--Medline/Pubmed, VHL and Science Direct--using the uniterms "alternative medicine", "low-power laser and acupuncture", "laser acupuncture and dentistry" and "laser therapy and acupuncture". Retrospective and prospective clinical studies were considered. According to the findings of the literature, laser therapy at points of acupuncture was effective for the treatment of various orofacial problems encountered in dentistry, but there are still many differences among the parameters used for irradiation and there is a lack of important information reported by the studies, such as the wavelength, dose, power density, irradiation time and frequency, points of acupuncture selected for irradiation and therapy outcomes. Although these results indicate the potential benefit of the use of laser therapy at points of acupuncture on Dentistry, further double-blinded, controlled clinical trials should be carried out in order to standardize protocols for clinical application. Copyright © 2015 Elsevier B.V. All rights reserved.

Barriers to leadership positions for Indian women in academic dentistry.

PubMed

Tandon, Shobha; Kohli, Anil; Bhalla, Sumati

2007-10-01

Indian women, have come up a long way during the past 50 years. Gone are the days when the leadership positions in dentistry and health care professions were occupied solely by males and the women in-charge were looked down upon as anomalies. The staff rooms in dental and medical schools, the research laboratories in India today are employing women, who have quietly begun challenging the conventional male ideas that had shaped the policies earlier on. Women have advanced considerably in academic dentistry but like every coin, this story too, has two sides. In spite of the considerable gain in equity of status, women in research and academic careers related to health care professions still face innumerable barriers to their careers. This study was conducted with an aim to highlight the various barriers being faced by women in leadership positions in academic dentistry in India and this paper also suggests issues which require global concern for unbiased advancement of women. This was a questionnaire-based study in which the subjects were women in leadership positions in the various dental colleges in India. The questions are related to the various barriers like family commitments, attitude of the society, sexual harassment, gender bias and lack of cooperation from spouse which hinders the development of the careers of such women with tremendous potential. The results show that 67% of the subjects feel there are more barriers to their careers as women than men and health care professions definitely need more women leaders for improvement in women's health status globally. 63.5% of women in dentistry feel their family commitments are barriers to rising in their careers and 64.7% report that a marriage is happier if the husband's career graph is better than wife's. The survey results indicate that the same salary is paid to 93.5% women as their male colleagues. The results of the study show that there certainly has been a change in outlook of Indian women as they have

Dentists' perceptions of trends in restorative dentistry in the UK.

PubMed

Randall, Ros C; Vrijhoef, Matthijs M A; Wilson, Nairn H F

2003-04-01

To obtain responses to a questionnaire on likely trends in the clinical practice of restorative dentistry from a national sample of general dental practitioners (GDPs) who were principals of group practices in the UK. A panel of nine experts had been convened previously to define areas of trends in restorative dentistry in the UK and to formulate these into statements. Twenty trends were identified and framed into a 22-item questionnaire based on the trend statements. The questionnaire was sent to a national sample of 2800 principal dentists in group practices. Names of principal dentists were taken from the Yellow Pages directories, a group practice being defined as at least one principal dentist and one other practitioner. Levels of agreement for questionnaire scores of > or = 70% for all segments of a statement were taken as indicating a possible trend. Of the 2800 questionnaires sent out, 1448 were returned, a return rate of 52%. Of these, 1217 questionnaires were usable, an overall response rate of 44%. Good agreement was obtained for 14 statements (64%). The 14 trend statements that scored a level of good agreement were taken as indicating possible trends in dentistry in the UK as perceived by those GDPs who responded to the questionnaire. However, in view of the fact that the 1217 usable questionnaires received reflected the opinions of 10% of the principal dentists in group practice in the UK, this will not be representative of all principal dentists in practice. Nevertheless for the purposes of gaining some insight into trends in restorative dentistry, it could be considered to be of value.

Thickness-Independent Ultrasonic Imaging Applied to Abrasive Cut-Off Wheels: An Advanced Aerospace Materials Characterization Method for the Abrasives Industry. A NASA Lewis Research Center Technology Transfer Case History

NASA Technical Reports Server (NTRS)

Roth, Don J.; Farmer, Donald A.

1998-01-01

Abrasive cut-off wheels are at times unintentionally manufactured with nonuniformity that is difficult to identify and sufficiently characterize without time-consuming, destructive examination. One particular nonuniformity is a density variation condition occurring around the wheel circumference or along the radius, or both. This density variation, depending on its severity, can cause wheel warpage and wheel vibration resulting in unacceptable performance and perhaps premature failure of the wheel. Conventional nondestructive evaluation methods such as ultrasonic c-scan imaging and film radiography are inaccurate in their attempts at characterizing the density variation because a superimposing thickness variation exists as well in the wheel. In this article, the single transducer thickness-independent ultrasonic imaging method, developed specifically to allow more accurate characterization of aerospace components, is shown to precisely characterize the extent of the density variation in a cut-off wheel having a superimposing thickness variation. The method thereby has potential as an effective quality control tool in the abrasives industry for the wheel manufacturer.