Accelerator-based conversion (ABC) of weapons plutonium: Plant layout study and related design issues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cowell, B.S.; Fontana, M.H.; Krakowski, R.A.

1995-04-01

In preparation for and in support of a detailed R and D Plan for the Accelerator-Based Conversion (ABC) of weapons plutonium, an ABC Plant Layout Study was conducted at the level of a pre-conceptual engineering design. The plant layout is based on an adaptation of the Molten-Salt Breeder Reactor (MSBR) detailed conceptual design that was completed in the early 1070s. Although the ABC Plant Layout Study included the Accelerator Equipment as an essential element, the engineering assessment focused primarily on the Target; Primary System (blanket and all systems containing plutonium-bearing fuel salt); the Heat-Removal System (secondary-coolant-salt and supercritical-steam systems); Chemicalmore » Processing; Operation and Maintenance; Containment and Safety; and Instrumentation and Control systems. Although constrained primarily to a reflection of an accelerator-driven (subcritical) variant of MSBR system, unique features and added flexibilities of the ABC suggest improved or alternative approaches to each of the above-listed subsystems; these, along with the key technical issues in need of resolution through a detailed R&D plan for ABC are described on the bases of the ``strawman`` or ``point-of-departure`` plant layout that resulted from this study.« less

Reducing Pesticide Drift

EPA Pesticide Factsheets

Provides information about pesticide spray drift, including problems associated with drift, managing risks from drift and the voluntary Drift Reduction Technology program that seeks to reduce spray drift through improved spray equipment design.

Optimization lighting layout based on gene density improved genetic algorithm for indoor visible light communications

NASA Astrophysics Data System (ADS)

Liu, Huanlin; Wang, Xin; Chen, Yong; Kong, Deqian; Xia, Peijie

2017-05-01

For indoor visible light communication system, the layout of LED lamps affects the uniformity of the received power on communication plane. In order to find an optimized lighting layout that meets both the lighting needs and communication needs, a gene density genetic algorithm (GDGA) is proposed. In GDGA, a gene indicates a pair of abscissa and ordinate of a LED, and an individual represents a LED layout in the room. The segmented crossover operation and gene mutation strategy based on gene density are put forward to make the received power on communication plane more uniform and increase the population's diversity. A weighted differences function between individuals is designed as the fitness function of GDGA for reserving the population having the useful LED layout genetic information and ensuring the global convergence of GDGA. Comparing square layout and circular layout, with the optimized layout achieved by the GDGA, the power uniformity increases by 83.3%, 83.1% and 55.4%, respectively. Furthermore, the convergence of GDGA is verified compared with evolutionary algorithm (EA). Experimental results show that GDGA can quickly find an approximation of optimal layout.

Rapid SAW Sensor Development Tools

NASA Technical Reports Server (NTRS)

Wilson, William C.; Atkinson, Gary M.

2007-01-01

The lack of integrated design tools for Surface Acoustic Wave (SAW) devices has led us to develop tools for the design, modeling, analysis, and automatic layout generation of SAW devices. These tools enable rapid development of wireless SAW sensors. The tools developed have been designed to integrate into existing Electronic Design Automation (EDA) tools to take advantage of existing 3D modeling, and Finite Element Analysis (FEA). This paper presents the SAW design, modeling, analysis, and automated layout generation tools.

Native conflict awared layout decomposition in triple patterning lithography using bin-based library matching method

NASA Astrophysics Data System (ADS)

Ke, Xianhua; Jiang, Hao; Lv, Wen; Liu, Shiyuan

2016-03-01

Triple patterning (TP) lithography becomes a feasible technology for manufacturing as the feature size further scale down to sub 14/10 nm. In TP, a layout is decomposed into three masks followed with exposures and etches/freezing processes respectively. Previous works mostly focus on layout decomposition with minimal conflicts and stitches simultaneously. However, since any existence of native conflict will result in layout re-design/modification and reperforming the time-consuming decomposition, the effective method that can be aware of native conflicts (NCs) in layout is desirable. In this paper, a bin-based library matching method is proposed for NCs detection and layout decomposition. First, a layout is divided into bins and the corresponding conflict graph in each bin is constructed. Then, we match the conflict graph in a prebuilt colored library, and as a result the NCs can be located and highlighted quickly.

A spatial multi-objective optimization model for sustainable urban wastewater system layout planning.

PubMed

Dong, X; Zeng, S; Chen, J

2012-01-01

Design of a sustainable city has changed the traditional centralized urban wastewater system towards a decentralized or clustering one. Note that there is considerable spatial variability of the factors that affect urban drainage performance including urban catchment characteristics. The potential options are numerous for planning the layout of an urban wastewater system, which are associated with different costs and local environmental impacts. There is thus a need to develop an approach to find the optimal spatial layout for collecting, treating, reusing and discharging the municipal wastewater of a city. In this study, a spatial multi-objective optimization model, called Urban wastewateR system Layout model (URL), was developed. It is solved by a genetic algorithm embedding Monte Carlo sampling and a series of graph algorithms. This model was illustrated by a case study in a newly developing urban area in Beijing, China. Five optimized system layouts were recommended to the local municipality for further detailed design.

Solving a layout design problem by analytic hierarchy process (AHP) and data envelopment analysis (DEA) approach

NASA Astrophysics Data System (ADS)

Tuzkaya, Umut R.; Eser, Arzum; Argon, Goner

2004-02-01

Today, growing amounts of waste due to fast consumption rate of products started an irreversible environmental pollution and damage. A considerable part of this waste is caused by packaging material. With the realization of this fact, various waste policies have taken important steps. Here we considered a firm, where waste Aluminum constitutes majority of raw materials for this fir0m. In order to achieve a profitable recycling process, plant layout should be well designed. In this study, we propose a two-step approach involving Analytic Hierarchy Process (AHP) and Data Envelopment Analysis (DEA) to solve facility layout design problems. A case example is considered to demonstrate the results achieved.

77 FR 58897 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-24

... will expedite such review and analysis. The Exchange proposes to publish by circular the layout of... submission of the entire data layout or may be limited to only certain components of the layout. The Exchange... consistent with the Section 6(b)(5) \\6\\ requirements that the rules of an exchange be designed to promote...

Study on workshop layout of a motorcycle company based on systematic layout planning (SLP)

NASA Astrophysics Data System (ADS)

Zhou, Kang-Qu; Zhang, Rui-Juan; Wang, Ying-Dong; Wang, Bing-Jie

2010-08-01

The method of SLP has been applied in a motorcycle company's layout planning. In this layout design, the related graphics have been used to illuminate the logistics and non-logistics relationships of every workshop to get the integrated relationships of workshops and preliminary plans. Comparing the two preliminary plans including logistics efficiency, space utilization, management conveniences, etc, an improvement solution is proposed. Through the improvement solution, the productivity has been increased by 18% and the production capacity is able to make 1600 engines each day.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christensen, C.; Horowitz, S.

In subdivisions, house orientations are largely determined by street layout. The resulting house orientations affect energy consumption (annual and on-peak) for heating and cooling, depending on window area distributions and shading from neighboring houses. House orientations also affect energy production (annual and on-peak) from solar thermal and photovoltaic systems, depending on available roof surfaces. Therefore, house orientations fundamentally influence both energy consumption and production, and an appropriate street layout is a prerequisite for taking full advantage of energy efficiency and renewable energy opportunities. The potential influence of street layout on solar performance is often acknowledged, but solar and energy issuesmore » must compete with many other criteria and constraints that influence subdivision street layout. When only general guidelines regarding energy are available, these factors may be ignored or have limited effect. Also, typical guidelines are often not site-specific and do not account for local parameters such as climate and the time value of energy. For energy to be given its due consideration in subdivision design, energy impacts need to be accurately quantified and displayed interactively to facilitate analysis of design alternatives. This paper describes a new computerized Subdivision Energy Analysis Tool being developed to allow users to interactively design subdivision street layouts while receiving feedback about energy impacts based on user-specified building design variants and availability of roof surfaces for photovoltaic and solar water heating systems.« less

A comparative evaluation of in-vehicle side view displays layouts in critical lane changing situation.

PubMed

Beck, Donghyun; Lee, Minho; Park, Woojin

2017-12-01

This study conducted a driving simulator experiment to comparatively evaluate three in-vehicle side view displays layouts for camera monitor systems (CMS) and the traditional side view mirror arrangement. The three layouts placed two electronic side view displays near the traditional mirrors positions, on the dashboard at each side of the steering wheel and on the centre fascia with the two displays joined side-by-side, respectively. Twenty-two participants performed a time- and safety-critical driving task that required rapidly gaining situation awareness through the side view displays/mirrors and making a lane change to avoid collision. The dependent variables were eye-off-the-road time, response time, and, ratings of perceived workload, preference and perceived safety. Overall, the layout placing the side view displays on the dashboard at each side of the steering wheel was found to be the best. The results indicated that reducing eye gaze travel distance and maintaining compatibility were both important for the design of CMS displays layout. Practitioner Summary: A driving simulator study was conducted to comparatively evaluate three in-vehicle side view displays layouts for camera monitor systems (CMS) and the traditional side view mirror arrangement in critical lane changing situation. Reducing eye movement and maintaining compatibility were found to be both important for the ergonomics design of CMS displays layout.

Tablet Keyboard Configuration Affects Performance, Discomfort and Task Difficulty for Thumb Typing in a Two-Handed Grip

PubMed Central

Trudeau, Matthieu B.; Catalano, Paul J.; Jindrich, Devin L.; Dennerlein, Jack T.

2013-01-01

When holding a tablet computer with two hands, the touch keyboard configuration imposes postural constraints on the user because of the need to simultaneously hold the device and type with the thumbs. Designers have provided users with several possible keyboard configurations (device orientation, keyboard layout and location). However, potential differences in performance, usability and postures among these configurations have not been explored. We hypothesize that (1) the narrower standard keyboard layout in the portrait orientation leads to lower self-reported discomfort and less reach than the landscape orientation; (2) a split keyboard layout results in better overall outcomes compared to the standard layout; and (3) the conventional bottom keyboard location leads to the best outcomes overall compared to other locations. A repeated measures laboratory experiment of 12 tablet owners measured typing speed, discomfort, task difficulty, and thumb/wrist joint postures using an active marker system during typing tasks for different combinations of device orientation (portrait and landscape), keyboard layout (standard and split), and keyboard location (bottom, middle, top). The narrower standard keyboard with the device in the portrait orientation was associated with less discomfort (least squares mean (and S.E.) 2.9±0.6) than the landscape orientation (4.5±0.7). Additionally, the split keyboard decreased the amount of reaching required by the thumb in the landscape orientation as defined by a reduced range of motion and less MCP extension, which may have led to reduced discomfort (2.7±0.6) compared to the standard layout (4.5±0.7). However, typing speed was greater for the standard layout (127±5 char./min.) compared to the split layout (113±4 char./min.) regardless of device orientation and keyboard location. Usage guidelines and designers can incorporate these findings to optimize keyboard design parameters and form factors that promote user performance and usability for thumb interaction. PMID:23840730

Tablet Keyboard Configuration Affects Performance, Discomfort and Task Difficulty for Thumb Typing in a Two-Handed Grip.

PubMed

Trudeau, Matthieu B; Catalano, Paul J; Jindrich, Devin L; Dennerlein, Jack T

2013-01-01

When holding a tablet computer with two hands, the touch keyboard configuration imposes postural constraints on the user because of the need to simultaneously hold the device and type with the thumbs. Designers have provided users with several possible keyboard configurations (device orientation, keyboard layout and location). However, potential differences in performance, usability and postures among these configurations have not been explored. We hypothesize that (1) the narrower standard keyboard layout in the portrait orientation leads to lower self-reported discomfort and less reach than the landscape orientation; (2) a split keyboard layout results in better overall outcomes compared to the standard layout; and (3) the conventional bottom keyboard location leads to the best outcomes overall compared to other locations. A repeated measures laboratory experiment of 12 tablet owners measured typing speed, discomfort, task difficulty, and thumb/wrist joint postures using an active marker system during typing tasks for different combinations of device orientation (portrait and landscape), keyboard layout (standard and split), and keyboard location (bottom, middle, top). The narrower standard keyboard with the device in the portrait orientation was associated with less discomfort (least squares mean (and S.E.) 2.9±0.6) than the landscape orientation (4.5±0.7). Additionally, the split keyboard decreased the amount of reaching required by the thumb in the landscape orientation as defined by a reduced range of motion and less MCP extension, which may have led to reduced discomfort (2.7±0.6) compared to the standard layout (4.5±0.7). However, typing speed was greater for the standard layout (127±5 char./min.) compared to the split layout (113±4 char./min.) regardless of device orientation and keyboard location. Usage guidelines and designers can incorporate these findings to optimize keyboard design parameters and form factors that promote user performance and usability for thumb interaction.

Automated ILA design for synchronous sequential circuits

NASA Technical Reports Server (NTRS)

Liu, M. N.; Liu, K. Z.; Maki, G. K.; Whitaker, S. R.

1991-01-01

An iterative logic array (ILA) architecture for synchronous sequential circuits is presented. This technique utilizes linear algebra to produce the design equations. The ILA realization of synchronous sequential logic can be fully automated with a computer program. A programmable design procedure is proposed to fullfill the design task and layout generation. A software algorithm in the C language has been developed and tested to generate 1 micron CMOS layouts using the Hewlett-Packard FUNGEN module generator shell.

Human Factors Analysis and Layout Guideline Development for the Canadian Surface Combatant (CSC) Project

DTIC Science & Technology

2013-04-01

project was to provide the Royal Canadian Navy ( RCN ) with a set of guidelines on analysis, design, and verification processes for effective room...design, and verification processes that should be used in the development of effective room layouts for Royal Canadian Navy ( RCN ) ships. The primary...designed CSC; however, the guidelines could be applied to the design of any multiple-operator space in any RCN vessel. Results: The development of

The Seated Soldier Study: Posture and Body Shape in Vehicle Seats

DTIC Science & Technology

2014-01-28

vehicle interior layout Current design guidance is based on outdated anthropometry Previous studies of seated anthropometry have not included the...personal protective equipment (PPE) for seat and vehicle interior layout • Current design guidance is based on outdated anthropometry • Previous...studies of seated anthropometry have not included the effects of PPE on posture and body shape • Detailed anthropometric data needed for the design

The theoretical ultimate magnetoelectric coefficients of magnetoelectric composites by optimization design

NASA Astrophysics Data System (ADS)

Wang, H.-L.; Liu, B.

2014-03-01

This paper investigates what is the largest magnetoelectric (ME) coefficient of ME composites, and how to realize it. From the standpoint of energy conservation, a theoretical analysis is carried out on an imaginary lever structure consisting of a magnetostrictive phase, a piezoelectric phase, and a rigid lever. This structure is a generalization of various composite layouts for optimization on ME effect. The predicted theoretical ultimate ME coefficient plays a similar role as the efficiency of ideal heat engine in thermodynamics, and is used to evaluate the existing typical ME layouts, such as the parallel sandwiched layout and the serial layout. These two typical layouts exhibit ME coefficient much lower than the theoretical largest values, because in the general analysis the stress amplification ratio and the volume ratio can be optimized independently and freely, but in typical layouts they are dependent or fixed. To overcome this shortcoming and achieve the theoretical largest ME coefficient, a new design is presented. In addition, it is found that the most commonly used electric field ME coefficient can be designed to be infinitely large. We doubt the validity of this coefficient as a reasonable ME effect index and consider three more ME coefficients, namely the electric charge ME coefficient, the voltage ME coefficient, and the static electric energy ME coefficient. We note that the theoretical ultimate value of the static electric energy ME coefficient is finite and might be a more proper measure of ME effect.

Layout design in order to improve efficiency in manufacturing

NASA Astrophysics Data System (ADS)

Siregar, I.; Tarigan, U.; Nasution, T. H.

2018-02-01

This research was conducted at the company that produces bobbins and ream type cigarette paper. Problems that found on the production process is the back and forth (back tracking) movement. Back and forth (back tracking) movement extending the total distance moved by the material and increase the total moment of transfer materials thus reducing the efficiency of the transfer of materials in the production process. The purpose of this study is to give design for the layout of production facilities in the company, so that the expected production produced by the company can reach the targets set by the management company. The method used in this research is the Graph-Based Construction and Travel Chart Method. The results of the analysis of the proposed layout with Graph-Based Construction was selected with a total value that is equal to the moment of transfer of 780 758 m / year. This result is better than the actual layout in the amount of 1,021,038.12 meters / year and the results of the method Travel Alternative Chart I of 826.236,60 meters/year, Alternative II of 1.004.433,56 meters / year, and Alternative III for 828,467.12 meters/year. The design layout of Graph-Based Construction material increases the transfer efficiency for 23.53%. With this layout proposal, expected production capacity will be increased along with the shortening of the distance of the displacement that must be passed by the material to be processed.

The theoretical ultimate magnetoelectric coefficients of magnetoelectric composites by optimization design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, H.-L.; Liu, B., E-mail: liubin@tsinghua.edu.cn

2014-03-21

This paper investigates what is the largest magnetoelectric (ME) coefficient of ME composites, and how to realize it. From the standpoint of energy conservation, a theoretical analysis is carried out on an imaginary lever structure consisting of a magnetostrictive phase, a piezoelectric phase, and a rigid lever. This structure is a generalization of various composite layouts for optimization on ME effect. The predicted theoretical ultimate ME coefficient plays a similar role as the efficiency of ideal heat engine in thermodynamics, and is used to evaluate the existing typical ME layouts, such as the parallel sandwiched layout and the serial layout.more » These two typical layouts exhibit ME coefficient much lower than the theoretical largest values, because in the general analysis the stress amplification ratio and the volume ratio can be optimized independently and freely, but in typical layouts they are dependent or fixed. To overcome this shortcoming and achieve the theoretical largest ME coefficient, a new design is presented. In addition, it is found that the most commonly used electric field ME coefficient can be designed to be infinitely large. We doubt the validity of this coefficient as a reasonable ME effect index and consider three more ME coefficients, namely the electric charge ME coefficient, the voltage ME coefficient, and the static electric energy ME coefficient. We note that the theoretical ultimate value of the static electric energy ME coefficient is finite and might be a more proper measure of ME effect.« less

Creative Computer Detective: The Basics of Teaching Desktop Publishing.

ERIC Educational Resources Information Center

Slothower, Jodie

Teaching desktop publishing (dtp) in college journalism classes is most effective when the instructor integrates into specific courses four types of software--a word processor, a draw program, a paint program and a layout program. In a course on design and layout, the instructor can demonstrate with the computer how good design can be created and…

Orbital transfer rocket engine technology 7.5K-LB thrust rocket engine preliminary design

NASA Technical Reports Server (NTRS)

Harmon, T. J.; Roschak, E.

1993-01-01

A preliminary design of an advanced LOX/LH2 expander cycle rocket engine producing 7,500 lbf thrust for Orbital Transfer vehicle missions was completed. Engine system, component and turbomachinery analysis at both on design and off design conditions were completed. The preliminary design analysis results showed engine requirements and performance goals were met. Computer models are described and model outputs are presented. Engine system assembly layouts, component layouts and valve and control system analysis are presented. Major design technologies were identified and remaining issues and concerns were listed.

Effects on driving performance of interacting with an in-vehicle music player: a comparison of three interface layout concepts for information presentation.

PubMed

Mitsopoulos-Rubens, Eve; Trotter, Margaret J; Lenné, Michael G

2011-05-01

Interface design is an important factor in assessing the potential effects on safety of interacting with an in-vehicle information system while driving. In the current study, the layout of information on a visual display was manipulated to explore its effect on driving performance in the context of music selection. The comparative effects of an auditory-verbal (cognitive) task were also explored. The driving performance of 30 participants was assessed under both baseline and dual task conditions using the Lane Change Test. Concurrent completion of the music selection task with driving resulted in significant impairment to lateral driving performance (mean lane deviation and percentage of correct lane changes) relative to the baseline, and significantly greater mean lane deviation relative to the combined driving and the cognitive task condition. The magnitude of these effects on driving performance was independent of layout concept, although significant differences in subjective workload estimates and performance on the music selection task across layout concepts highlights that potential uncertainty regarding design use as conveyed through layout concept could be disadvantageous. The implications of these results for interface design and safety are discussed. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Using RGB-D sensors and evolutionary algorithms for the optimization of workstation layouts.

PubMed

Diego-Mas, Jose Antonio; Poveda-Bautista, Rocio; Garzon-Leal, Diana

2017-11-01

RGB-D sensors can collect postural data in an automatized way. However, the application of these devices in real work environments requires overcoming problems such as lack of accuracy or body parts' occlusion. This work presents the use of RGB-D sensors and genetic algorithms for the optimization of workstation layouts. RGB-D sensors are used to capture workers' movements when they reach objects on workbenches. Collected data are then used to optimize workstation layout by means of genetic algorithms considering multiple ergonomic criteria. Results show that typical drawbacks of using RGB-D sensors for body tracking are not a problem for this application, and that the combination with intelligent algorithms can automatize the layout design process. The procedure described can be used to automatically suggest new layouts when workers or processes of production change, to adapt layouts to specific workers based on their ways to do the tasks, or to obtain layouts simultaneously optimized for several production processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Layout decomposition of self-aligned double patterning for 2D random logic patterning

NASA Astrophysics Data System (ADS)

Ban, Yongchan; Miloslavsky, Alex; Lucas, Kevin; Choi, Soo-Han; Park, Chul-Hong; Pan, David Z.

2011-04-01

Self-aligned double pattering (SADP) has been adapted as a promising solution for sub-30nm technology nodes due to its lower overlay problem and better process tolerance. SADP is in production use for 1D dense patterns with good pitch control such as NAND Flash memory applications, but it is still challenging to apply SADP to 2D random logic patterns. The favored type of SADP for complex logic interconnects is a two mask approach using a core mask and a trim mask. In this paper, we first describe layout decomposition methods of spacer-type double patterning lithography, then report a type of SADP compliant layouts, and finally report SADP applications on Samsung 22nm SRAM layout. For SADP decomposition, we propose several SADP-aware layout coloring algorithms and a method of generating lithography-friendly core mask patterns. Experimental results on 22nm node designs show that our proposed layout decomposition for SADP effectively decomposes any given layouts.

Optimization of RET flow using test layout

NASA Astrophysics Data System (ADS)

Zhang, Yunqiang; Sethi, Satyendra; Lucas, Kevin

2008-11-01

At advanced technology nodes with extremely low k1 lithography, it is very hard to achieve image fidelity requirements and process window for some layout configurations. Quite often these layouts are within simple design rule constraints for a given technology node. It is important to have these layouts included during early RET flow development. Most of RET developments are based on shrunk layout from the previous technology node, which is possibly not good enough. A better methodology in creating test layout is required for optical proximity correction (OPC) recipe and assists feature development. In this paper we demonstrate the application of programmable test layouts in RET development. Layout pattern libraries are developed and embedded in a layout tool (ICWB). Assessment gauges are generated together with patterns for quick correction accuracy assessment. Several groups of test pattern libraries have been developed based on learning from product patterns and a layout DOE approach. The interaction between layout patterns and OPC recipe has been studied. Correction of a contact layer is quite challenge because of poor convergence and low process window. We developed test pattern library with many different contact configurations. Different OPC schemes are studied on these test layouts. The worst process window patterns are pinpointed for a given illumination condition. Assist features (AF) are frequently placed according to pre-determined rules to improve lithography process window. These rules are usually derived from lithographic models and experiments. Direct validation of AF rules is required at development phase. We use the test layout approach to determine rules in order to eliminate AF printability problem.

Decision Support System for Coastal Protection Layout Design (DSS4CPD) Using Genetic Algorithm (ga) and Multicriteria Analysis (mca)

NASA Astrophysics Data System (ADS)

Jinchai, Phinai; Chittaladakorn, Suwatana

This research has its objective to develop the decision support system on GIS to be used in the coastal erosion protection management. The developed model in this research is called Decision Support System for Coastal Protection Layout Design (DSS4CPD). It has created both for systematic protection and solution measures to the problem by using Genetic Algorithm (GA) and Multicriteria Analysis (MCA) for finding the coastal structure layout optimal solution. In this research, three types of coastal structures were used as structure alternatives for the layout, which are seawall, breakwater, and groin. The coastal area in Nakornsrithammaraj, Thailand was used as the case study. The studied result has found the appropriate position of coastal structures considering the suitable rock size relied on the wave energy, and the appropriate coastal structure position based on the wave breaking line. Using GA and MCA in DSS4CPD, it found the best layout in this project. This DSS4CPD will be used by the authorized decision makers to find the most suitable erosion problem solution.

Photomask and pattern programming manual

NASA Technical Reports Server (NTRS)

Kirschman, R. K.

1978-01-01

A user's manual for a set of computer programs written in FORTRAN for the layout and generation of photomasks is presented. A limited amount of related information on photomasks, their design, and use is included. Input to the programs includes data describing the photomask design. Possible outputs include plots of the layout and a magnetic tape for controlling generation of the photomask by a pattern generator.

14 CFR 151.111 - Advance planning proposals: General.

Code of Federal Regulations, 2013 CFR

2013-01-01

... airport layout plan, under § 151.5(a), or the development of plans designed to lead to a project... proposal must relate to an airport layout plan or plans and specifications for the development of a new...

14 CFR 151.111 - Advance planning proposals: General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... airport layout plan, under § 151.5(a), or the development of plans designed to lead to a project... proposal must relate to an airport layout plan or plans and specifications for the development of a new...

14 CFR 151.111 - Advance planning proposals: General.

Code of Federal Regulations, 2012 CFR

2012-01-01

... airport layout plan, under § 151.5(a), or the development of plans designed to lead to a project... proposal must relate to an airport layout plan or plans and specifications for the development of a new...

14 CFR 151.111 - Advance planning proposals: General.

Code of Federal Regulations, 2014 CFR

2014-01-01

... airport layout plan, under § 151.5(a), or the development of plans designed to lead to a project... proposal must relate to an airport layout plan or plans and specifications for the development of a new...

A procedural method for the efficient implementation of full-custom VLSI designs

NASA Technical Reports Server (NTRS)

Belk, P.; Hickey, N.

1987-01-01

An imbedded language system for the layout of very large scale integration (VLSI) circuits is examined. It is shown that through the judicious use of this system, a large variety of circuits can be designed with circuit density and performance comparable to traditional full-custom design methods, but with design costs more comparable to semi-custom design methods. The high performance of this methodology is attributable to the flexibility of procedural descriptions of VLSI layouts and to a number of automatic and semi-automatic tools within the system.

The use of multidimensional scaling for facilities layout - An application to the design of the Space Station

NASA Technical Reports Server (NTRS)

Tullis, Thomas S.; Bied Sperling, Barbra; Steinberg, A. L.

1986-01-01

Before an optimum layout of the facilities for the proposed Space Station can be designed, it is necessary to understand the functions that will be performed by the Space Station crew and the relationships among those functions. Five criteria for assessing functional relationships were identified. For each of these criteria, a matrix representing the degree of association of all pairs of functions was developed. The key to making inferences about the layout of the Space Station from these matrices was the use of multidimensional scaling (MDS). Applying MDS to these matrices resulted in spatial configurations of the crew functions in which smaller distances in the MDS configuration reflected closer associations. An MDS analysis of a composite matrix formed by combining the five individual matrices resulted in two dimensions that describe the configuration: a 'private-public' dimension and a 'group-individual' dimension. Seven specific recommendations for Space Station layout were derived from analyses of the MDS configurations. Although these techniques have been applied to the design of the Space Station, they can be applied to the design of any facility where people live or work.

Optimizing longwall mine layouts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minkel, M.J.

1996-12-31

Before spending the time to design an underground mine in detail, the mining engineer should be assured of the economic viability of the location of the layout. This has historically been a trial-and-error, iterative process. Traditional underground mine planning usually bases the layout on the geological characteristics of a deposit such as minimum seam height, quality, and the absence of faults. Whether one attempts to make a decision manually. or use traditional mine planning software, the process works something like this: First you build geological model. Then you impose a {open_quotes}best guess{close_quotes} as to which geological layers will become partmore » of the mined product, or will influence mining. Next you place your design where you believe is the best location to make a mine. Then you select equipment which you believe will cost-effectively mine the area. Finally, you schedule your equipment selection through the design over the mine life, run financial analyses and see if the rate of return is acceptable. If the NPV is acceptable, the design is accepted. If the NPV is not acceptable, the engineer has to restart the cycle of redesigning the layout, rescheduling the equipment, and restudying the economics again.« less

A hybrid intelligence approach to artifact recognition in digital publishing

NASA Astrophysics Data System (ADS)

Vega-Riveros, J. Fernando; Santos Villalobos, Hector J.

2006-02-01

The system presented integrates rule-based and case-based reasoning for artifact recognition in Digital Publishing. In Variable Data Printing (VDP) human proofing could result prohibitive since a job could contain millions of different instances that may contain two types of artifacts: 1) evident defects, like a text overflow or overlapping 2) style-dependent artifacts, subtle defects that show as inconsistencies with regard to the original job design. We designed a Knowledge-Based Artifact Recognition tool for document segmentation, layout understanding, artifact detection, and document design quality assessment. Document evaluation is constrained by reference to one instance of the VDP job proofed by a human expert against the remaining instances. Fundamental rules of document design are used in the rule-based component for document segmentation and layout understanding. Ambiguities in the design principles not covered by the rule-based system are analyzed by case-based reasoning, using the Nearest Neighbor Algorithm, where features from previous jobs are used to detect artifacts and inconsistencies within the document layout. We used a subset of XSL-FO and assembled a set of 44 document samples. The system detected all the job layout changes, while obtaining an overall average accuracy of 84.56%, with the highest accuracy of 92.82%, for overlapping and the lowest, 66.7%, for the lack-of-white-space.

Distribution uniformity of laser-accelerated proton beams

NASA Astrophysics Data System (ADS)

Zhu, Jun-Gao; Zhu, Kun; Tao, Li; Xu, Xiao-Han; Lin, Chen; Ma, Wen-Jun; Lu, Hai-Yang; Zhao, Yan-Ying; Lu, Yuan-Rong; Chen, Jia-Er; Yan, Xue-Qing

2017-09-01

Compared with conventional accelerators, laser plasma accelerators can generate high energy ions at a greatly reduced scale, due to their TV/m acceleration gradient. A compact laser plasma accelerator (CLAPA) has been built at the Institute of Heavy Ion Physics at Peking University. It will be used for applied research like biological irradiation, astrophysics simulations, etc. A beamline system with multiple quadrupoles and an analyzing magnet for laser-accelerated ions is proposed here. Since laser-accelerated ion beams have broad energy spectra and large angular divergence, the parameters (beam waist position in the Y direction, beam line layout, drift distance, magnet angles etc.) of the beamline system are carefully designed and optimised to obtain a radially symmetric proton distribution at the irradiation platform. Requirements of energy selection and differences in focusing or defocusing in application systems greatly influence the evolution of proton distributions. With optimal parameters, radially symmetric proton distributions can be achieved and protons with different energy spread within ±5% have similar transverse areas at the experiment target. Supported by National Natural Science Foundation of China (11575011, 61631001) and National Grand Instrument Project (2012YQ030142)

New drift chamber technology for high energy gamma-ray telescopes

NASA Astrophysics Data System (ADS)

Hunter, Stanley D.; Cuddapah, Rajani

1990-08-01

Work to develop a low-power amplifier and discriminator for use on space qualifiable drift chambers is discussed. Consideration is given to the goals of the next generation of high-energy gamma-ray telescope design and to how the goals can be achieved using xenon gas drift chambers. The design and construction of a low power drift chamber amplifier and discriminator are described, and the design of a quad-time-to-amplitude converter is outlined.

Feasibility of Supersonic Aircraft Concepts for Low-Boom and Flight Trim Constraints

NASA Technical Reports Server (NTRS)

Li, Wu

2015-01-01

This paper documents a process for analyzing whether a particular supersonic aircraft configuration layout and a given cruise condition are feasible to achieve a trimmed low-boom design. This process was motivated by the need to know whether a particular configuration at a given cruise condition could be reshaped to satisfy both low-boom and flight trim constraints. Without such a process, much effort could be wasted on shaping a configuration layout at a cruise condition that could never satisfy both low-boom and flight trim constraints simultaneously. The process helps to exclude infeasible configuration layouts with minimum effort and allows a designer to develop trimmed low-boom concepts more effectively. A notional low-boom supersonic demonstrator concept is used to illustrate the analysis/design process.

OpenDrift v1.0: a generic framework for trajectory modelling

NASA Astrophysics Data System (ADS)

Dagestad, Knut-Frode; Röhrs, Johannes; Breivik, Øyvind; Ådlandsvik, Bjørn

2018-04-01

OpenDrift is an open-source Python-based framework for Lagrangian particle modelling under development at the Norwegian Meteorological Institute with contributions from the wider scientific community. The framework is highly generic and modular, and is designed to be used for any type of drift calculations in the ocean or atmosphere. A specific module within the OpenDrift framework corresponds to a Lagrangian particle model in the traditional sense. A number of modules have already been developed, including an oil drift module, a stochastic search-and-rescue module, a pelagic egg module, and a basic module for atmospheric drift. The framework allows for the ingestion of an unspecified number of forcing fields (scalar and vectorial) from various sources, including Eulerian ocean, atmosphere and wave models, but also measurements or a priori values for the same variables. A basic backtracking mechanism is inherent, using sign reversal of the total displacement vector and negative time stepping. OpenDrift is fast and simple to set up and use on Linux, Mac and Windows environments, and can be used with minimal or no Python experience. It is designed for flexibility, and researchers may easily adapt or write modules for their specific purpose. OpenDrift is also designed for performance, and simulations with millions of particles may be performed on a laptop. Further, OpenDrift is designed for robustness and is in daily operational use for emergency preparedness modelling (oil drift, search and rescue, and drifting ships) at the Norwegian Meteorological Institute.

First results of a novel Silicon Drift Detector array designed for low energy X-ray fluorescence spectroscopy

NASA Astrophysics Data System (ADS)

Rachevski, Alexandre; Ahangarianabhari, Mahdi; Bellutti, Pierluigi; Bertuccio, Giuseppe; Brigo, Elena; Bufon, Jernej; Carrato, Sergio; Castoldi, Andrea; Cautero, Giuseppe; Fabiani, Sergio; Giacomini, Gabriele; Gianoncelli, Alessandra; Giuressi, Dario; Guazzoni, Chiara; Kourousias, George; Liu, Chang; Menk, Ralf Hendrik; Montemurro, Giuseppe Vito; Picciotto, Antonino; Piemonte, Claudio; Rashevskaya, Irina; Shi, Yongbiao; Stolfa, Andrea; Vacchi, Andrea; Zampa, Gianluigi; Zampa, Nicola; Zorzi, Nicola

2016-07-01

We developed a trapezoidal shaped matrix with 8 cells of Silicon Drift Detectors (SDD) featuring a very low leakage current (below 180 pA/cm2 at 20 °C) and a shallow uniformly implanted p+ entrance window that enables sensitivity down to few hundreds of eV. The matrix consists of a completely depleted volume of silicon wafer subdivided into 4 square cells and 4 half-size triangular cells. The energy resolution of a single square cell, readout by the ultra-low noise SIRIO charge sensitive preamplifier, is 158 eV FWHM at 5.9 keV and 0 °C. The total sensitive area of the matrix is 231 mm2 and the wafer thickness is 450 μm. The detector was developed in the frame of the INFN R&D project ReDSoX in collaboration with FBK, Trento. Its trapezoidal shape was chosen in order to optimize the detection geometry for the experimental requirements of low energy X-ray fluorescence (LEXRF) spectroscopy, aiming at achieving a large detection angle. We plan to exploit the complete detector at the TwinMic spectromicroscopy beamline at the Elettra Synchrotron (Trieste, Italy). The complete system, composed of 4 matrices, increases the solid angle coverage of the isotropic photoemission hemisphere about 4 times over the present detector configuration. We report on the layout of the SDD matrix and of the experimental set-up, as well as the spectroscopic performance measured both in the laboratory and at the experimental beamline.

A user's manual for DELSOL3: A computer code for calculating the optical performance and optimal system design for solar thermal central receiver plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kistler, B.L.

DELSOL3 is a revised and updated version of the DELSOL2 computer program (SAND81-8237) for calculating collector field performance and layout and optimal system design for solar thermal central receiver plants. The code consists of a detailed model of the optical performance, a simpler model of the non-optical performance, an algorithm for field layout, and a searching algorithm to find the best system design based on energy cost. The latter two features are coupled to a cost model of central receiver components and an economic model for calculating energy costs. The code can handle flat, focused and/or canted heliostats, and externalmore » cylindrical, multi-aperture cavity, and flat plate receivers. The program optimizes the tower height, receiver size, field layout, heliostat spacings, and tower position at user specified power levels subject to flux limits on the receiver and land constraints for field layout. DELSOL3 maintains the advantages of speed and accuracy which are characteristics of DELSOL2.« less

Brunn: an open source laboratory information system for microplates with a graphical plate layout design process.

PubMed

Alvarsson, Jonathan; Andersson, Claes; Spjuth, Ola; Larsson, Rolf; Wikberg, Jarl E S

2011-05-20

Compound profiling and drug screening generates large amounts of data and is generally based on microplate assays. Current information systems used for handling this are mainly commercial, closed source, expensive, and heavyweight and there is a need for a flexible lightweight open system for handling plate design, and validation and preparation of data. A Bioclipse plugin consisting of a client part and a relational database was constructed. A multiple-step plate layout point-and-click interface was implemented inside Bioclipse. The system contains a data validation step, where outliers can be removed, and finally a plate report with all relevant calculated data, including dose-response curves. Brunn is capable of handling the data from microplate assays. It can create dose-response curves and calculate IC50 values. Using a system of this sort facilitates work in the laboratory. Being able to reuse already constructed plates and plate layouts by starting out from an earlier step in the plate layout design process saves time and cuts down on error sources.

Numerical investigation on layout optimization of obstacles in a three-dimensional passive micromixer.

PubMed

Chen, Xueye; Zhao, Zhongyi

2017-04-29

This paper aims at layout optimization design of obstacles in a three-dimensional T-type micromixer. Numerical analysis shows that the direction of flow velocity change constantly due to the obstacles blocking, which produces the chaotic convection and increases species mixing effectively. The orthogonal experiment method was applied for determining the effects of some key parameters on mixing efficiency. The weights in the order are: height of obstacles > geometric shape > symmetry = number of obstacles. Based on the optimized results, a multi-units obstacle micromixer was designed. Compared with T-type micromixer, the multi-units obstacle micromixer is more efficient, and more than 90% mixing efficiency were obtained for a wide range of peclet numbers. It can be demonstrated that the presented optimal design method of obstacles layout in three-dimensional microchannels is a simple and effective technology to improve species mixing in microfluidic devices. The obstacles layout methodology has the potential for applications in chemical engineering and bioengineering. Copyright © 2017 Elsevier B.V. All rights reserved.

Ensuring production-worthy OPC recipes using large test structure arrays

NASA Astrophysics Data System (ADS)

Cork, Christopher; Zimmermann, Rainer; Mei, Xin; Shahin, Alexander

2007-03-01

The continual shrinking of design rules as the industry follows Moore's Law and the associated need for low k1 processes, have resulted in more layout configurations becoming difficult to print within the required tolerances. OPC recipes have needed to become more complex as tolerances decreased and acceptable corrections harder to find with simple algorithms. With this complexity comes the possibility of coding errors and ensuring the solutions are truly general. OPC Verification tools can check the quality of a correction based on pre-determined specifications for CD variation, line-end pullback and Edge Placement Error and then highlight layout configuration where violations are found. The problem facing a Mask Tape-Out group is that they usually have little control over the Design Styles coming in. Different approaches to eliminating problematic layouts have included highly restrictive Design Rules [1], whereby certain pitches or orientations are disallowed. Now these design rules are either becoming too complex or they overly restrict the designer from benefiting from the reduced pitch of the new node. The tight link between Design and Mask Tape-Out found in Integrated Device Manufacturers [2] (IDMs) i.e. companies that control both design and manufacturing can do much to dictate manufacturing friendly layout styles, and push ownership of problem resolution back to design groups. In fact this has been perceived as such an issue that a new class of products for designers that perform Lithographic Compliance Check on design layout is an emerging technology [3]. In contrast to IDMs, Semiconductor Foundries are presented with a much larger variety of design styles and a set of Fabless customers who generally are less knowledgeable in terms of understanding the impact of their layout on manufacturability and how to correct issues. The robustness requirements of a foundry's OPC correction recipe, therefore needs to be greater than that for an IDM's tape-out group. An OPC correction recipe which gives acceptable verification results, based solely on one customer GDS is clearly not sufficient to guarantee that all future tape-outs from multiple customers will be similarly clean. Ad hoc changes made in reaction to problems seen at verification are risky, while they may solve one particular layout issue on one product there is no guarantee that the problem may simply shift to another configuration on a yet to be manufactured part. The need to re-qualify a recipe over multiple products at each recipe change can easily results in excessive computational requirements. A single layer at an advanced node typically needs overnight runs on a large processor farm. Much of this layout, however, is extremely repetitive, made from a few standard cells placed tens of thousands of times. An alternative and more efficient approach, suggested by this paper as a screening methodology, is to encapsulate the problematic structures into a programmable test structure array. The dimensions of these test structures are parameterized in software such that they can be generated with these dimensions varied over the space of the design rules and conceivable design styles. By verifying the new recipe over these test structures one could more quickly gain confidence that this recipe would be robust over multiple tape-outs. This paper gives some examples of the implementation of this methodology.

Automatic page layout using genetic algorithms for electronic albuming

NASA Astrophysics Data System (ADS)

Geigel, Joe; Loui, Alexander C. P.

2000-12-01

In this paper, we describe a flexible system for automatic page layout that makes use of genetic algorithms for albuming applications. The system is divided into two modules, a page creator module which is responsible for distributing images amongst various album pages, and an image placement module which positions images on individual pages. Final page layouts are specified in a textual form using XML for printing or viewing over the Internet. The system makes use of genetic algorithms, a class of search and optimization algorithms that are based on the concepts of biological evolution, for generating solutions with fitness based on graphic design preferences supplied by the user. The genetic page layout algorithm has been incorporated into a web-based prototype system for interactive page layout over the Internet. The prototype system is built using client-server architecture and is implemented in java. The system described in this paper has demonstrated the feasibility of using genetic algorithms for automated page layout in albuming and web-based imaging applications. We believe that the system adequately proves the validity of the concept, providing creative layouts in a reasonable number of iterations. By optimizing the layout parameters of the fitness function, we hope to further improve the quality of the final layout in terms of user preference and computation speed.

A Study of Vehicle Structural Layouts in Post-WWII Aircraft

NASA Technical Reports Server (NTRS)

Sensmeier, Mark D.; Samareh, Jamshid A.

2004-01-01

In this paper, results of a study of structural layouts of post-WWII aircraft are presented. This study was undertaken to provide the background information necessary to determine typical layouts, design practices, and industry trends in aircraft structural design. Design decisions are often predicated not on performance-related criteria, but rather on such factors as manufacturability, maintenance access, and of course cost. For this reason, a thorough understanding of current best practices in the industry is required as an input for the design optimization process. To determine these best practices and industry trends, a large number of aircraft structural cutaway illustrations were analyzed for five different aircraft categories (commercial transport jets, business jets, combat jet aircraft, single engine propeller aircraft, and twin-engine propeller aircraft). Several aspects of wing design and fuselage design characteristics are presented here for the commercial transport and combat aircraft categories. A great deal of commonality was observed for transport structure designs over a range of eras and manufacturers. A much higher degree of variability in structural designs was observed for the combat aircraft, though some discernable trends were observed as well.

Automatic Optimization of Wayfinding Design.

PubMed

Huang, Haikun; Lin, Ni-Ching; Barrett, Lorenzo; Springer, Darian; Wang, Hsueh-Cheng; Pomplun, Marc; Yu, Lap-Fai

2017-10-10

Wayfinding signs play an important role in guiding users to navigate in a virtual environment and in helping pedestrians to find their ways in a real-world architectural site. Conventionally, the wayfinding design of a virtual environment is created manually, so as the wayfinding design of a real-world architectural site. The many possible navigation scenarios, and the interplay between signs and human navigation, can make the manual design process overwhelming and non-trivial. As a result, creating a wayfinding design for a typical layout can take months to several years. In this paper, we introduce the Way to Go! approach for automatically generating a wayfinding design for a given layout. The designer simply has to specify some navigation scenarios; our approach will automatically generate an optimized wayfinding design with signs properly placed considering human agents' visibility and possibility of making navigation mistakes. We demonstrate the effectiveness of our approach in generating wayfinding designs for different layouts. We evaluate our results by comparing different wayfinding designs and show that our optimized designs can guide pedestrians to their destinations effectively. Our approach can also help the designer visualize the accessibility of a destination from different locations, and correct any "blind zone" with additional signs.

Task-specific performance effects with different numeric keypad layouts.

PubMed

Armand, Jenny T; Redick, Thomas S; Poulsen, Joan R

2014-07-01

Two commonly used keypad arrangements are the telephone and calculator layouts. The purpose of this study was to determine if entering different types of numeric information was quicker and more accurate with the telephone or the calculator layout on a computer keyboard numeric keypad. Fifty-seven participants saw a 10-digit numeric stimulus to type with a computer number keypad as quickly and as accurately as possible. Stimuli were presented in either a numerical [1,234,567,890] or phone [(123) 456-7890] format. The results indicated that participants' memory of the layout for the arrangement of keys on a telephone was significantly better than the layout of a calculator. In addition, the results showed that participants were more accurate when entering stimuli using the calculator keypad layout. Critically, participants' response times showed an interaction of stimulus format and keypad layout: participants were specifically slowed when entering numeric stimuli using a telephone keypad layout. Responses made using the middle row of keys were faster and more accurate than responses using the top and bottom row of keys. Implications for keypad design and cell phone usage are discussed. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

A unified approach to VLSI layout automation and algorithm mapping on processor arrays

NASA Technical Reports Server (NTRS)

Venkateswaran, N.; Pattabiraman, S.; Srinivasan, Vinoo N.

1993-01-01

Development of software tools for designing supercomputing systems is highly complex and cost ineffective. To tackle this a special purpose PAcube silicon compiler which integrates different design levels from cell to processor arrays has been proposed. As a part of this, we present in this paper a novel methodology which unifies the problems of Layout Automation and Algorithm Mapping.

Terrace Layout Using a Computer Assisted System

USDA-ARS?s Scientific Manuscript database

Development of a web-based terrace design tool based on the MOTERR program is presented, along with representative layouts for conventional and parallel terrace systems. Using digital elevation maps and geographic information systems (GIS), this tool utilizes personal computers to rapidly construct ...

77 FR 50092 - Duke Energy Carolinas, LLC; Notice of Application for Amendment of License and Soliciting...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-20

... layout is mostly similar to the originally-approved design except that the docks have shifted location... Application: Duke Energy Carolinas, LLC requests after-the-fact Commission approval to amend the layout of...

Design of motion adjusting system for space camera based on ultrasonic motor

NASA Astrophysics Data System (ADS)

Xu, Kai; Jin, Guang; Gu, Song; Yan, Yong; Sun, Zhiyuan

2011-08-01

Drift angle is a transverse intersection angle of vector of image motion of the space camera. Adjusting the angle could reduce the influence on image quality. Ultrasonic motor (USM) is a new type of actuator using ultrasonic wave stimulated by piezoelectric ceramics. They have many advantages in comparison with conventional electromagnetic motors. In this paper, some improvement was designed for control system of drift adjusting mechanism. Based on ultrasonic motor T-60 was designed the drift adjusting system, which is composed of the drift adjusting mechanical frame, the ultrasonic motor, the driver of Ultrasonic Motor, the photoelectric encoder and the drift adjusting controller. The TMS320F28335 DSP was adopted as the calculation and control processor, photoelectric encoder was used as sensor of position closed loop system and the voltage driving circuit designed as generator of ultrasonic wave. It was built the mathematic model of drive circuit of the ultrasonic motor T-60 using matlab modules. In order to verify the validity of the drift adjusting system, was introduced the source of the disturbance, and made simulation analysis. It designed the control systems of motor drive for drift adjusting system with the improved PID control. The drift angle adjusting system has such advantages as the small space, simple configuration, high position control precision, fine repeatability, self locking property and low powers. It showed that the system could accomplish the mission of drift angle adjusting excellent.

Design of an S band narrow-band bandpass BAW filter

NASA Astrophysics Data System (ADS)

Gao, Yang; Zhao, Kun-li; Han, Chao

2017-11-01

An S band narrowband bandpass filter BAW with center frequency 2.460 GHz, bandwidth 41MHz, band insertion loss - 1.154 dB, the passband ripple 0.9 dB, the out of band rejection about -42.5dB@2.385 GHz; -45.5dB@2.506 GHz was designed for potential UAV measurement and control applications. According to the design specifications, the design is as follows: each FBAR's stack was designed in BAW filter by using Mason model. Each FBAR's shape was designed with the method of apodization electrode. The layout of BAW filter was designed. The acoustic-electromagnetic cosimulation model was built to validate the performance of the designed BAW filter. The presented design procedure is a common one, and there are two characteristics: 1) an A and EM co-simulation method is used for the final BAW filter performance validation in the design stage, thus ensures over-optimistic designs by the bare 1D Mason model are found and rejected in time; 2) An in-house developed auto-layout method is used to get compact BAW filter layout, which simplifies iterative error-and-try work here and output necessary in-plane geometry information to the A and EM cosimulation model.

Effect of a workplace design and training intervention on individual performance, group effectiveness and collaboration: the role of environmental control.

PubMed

Robertson, Michelle M; Huang, Yueng-Hsiang

2006-01-01

The effects of a workplace design and training intervention and the relationships between perceived satisfaction of office workplace design factors (layout and storage) and work performance measures (individual performance, group collaboration and effectiveness) were studied with 120 office workers using the Workplace Environment Questionnaire. Further, we examined whether environmental control had a direct effect on work performance, and then explored whether environmental control mediated or moderated the relationship between workplace design factors and work performance. Results showed a significant, positive impact of the intervention on environmental satisfaction for workstation layout. Satisfaction with workstation layout had a significant relationship with individual performance, group collaboration and effectiveness; and satisfaction with workstation storage had a significant relationship with individual performance and group collaboration. Environmental control had a direct impact on individual performance and group collaboration; whereas, the mediating and moderating effects of environmental control on the relationship between workplace design factors and outcome variables were not significant.

Design of Flight Control Panel Layout using Graphical User Interface in MATLAB

NASA Astrophysics Data System (ADS)

Wirawan, A.; Indriyanto, T.

2018-04-01

This paper introduces the design of Flight Control Panel (FCP) Layout using Graphical User Interface in MATLAB. The FCP is the interface to give the command to the simulation and to monitor model variables while the simulation is running. The command accommodates by the FCP are altitude command, the angle of sideslip command, heading command, and setting command for turbulence model. The FCP was also designed to monitor the flight parameter while the simulation is running.

Layout optimization using the homogenization method

NASA Technical Reports Server (NTRS)

Suzuki, Katsuyuki; Kikuchi, Noboru

1993-01-01

A generalized layout problem involving sizing, shape, and topology optimization is solved by using the homogenization method for three-dimensional linearly elastic shell structures in order to seek a possibility of establishment of an integrated design system of automotive car bodies, as an extension of the previous work by Bendsoe and Kikuchi. A formulation of a three-dimensional homogenized shell, a solution algorithm, and several examples of computing the optimum layout are presented in this first part of the two articles.

Destination bedside: using research findings to visualize optimal unit layouts and health information technology in support of bedside care.

PubMed

Watkins, Nicholas; Kennedy, Mary; Lee, Nelson; O'Neill, Michael; Peavey, Erin; Ducharme, Maria; Padula, Cynthia

2012-05-01

This study explored the impact of unit design and healthcare information technology (HIT) on nursing workflow and patient-centered care (PCC). Healthcare information technology and unit layout-related predictors of nursing workflow and PCC were measured during a 3-phase study involving questionnaires and work sampling methods. Stepwise multiple linear regressions demonstrated several HIT and unit layout-related factors that impact nursing workflow and PCC.

Layout design-based research on optimization and assessment method for shipbuilding workshop

NASA Astrophysics Data System (ADS)

Liu, Yang; Meng, Mei; Liu, Shuang

2013-06-01

The research study proposes to examine a three-dimensional visualization program, emphasizing on improving genetic algorithms through the optimization of a layout design-based standard and discrete shipbuilding workshop. By utilizing a steel processing workshop as an example, the principle of minimum logistic costs will be implemented to obtain an ideological equipment layout, and a mathematical model. The objectiveness is to minimize the total necessary distance traveled between machines. An improved control operator is implemented to improve the iterative efficiency of the genetic algorithm, and yield relevant parameters. The Computer Aided Tri-Dimensional Interface Application (CATIA) software is applied to establish the manufacturing resource base and parametric model of the steel processing workshop. Based on the results of optimized planar logistics, a visual parametric model of the steel processing workshop is constructed, and qualitative and quantitative adjustments then are applied to the model. The method for evaluating the results of the layout is subsequently established through the utilization of AHP. In order to provide a mode of reference to the optimization and layout of the digitalized production workshop, the optimized discrete production workshop will possess a certain level of practical significance.

An online planning tool for designing terrace layouts

USDA-ARS?s Scientific Manuscript database

A web-based conservation planning tool, WebTERLOC (web-based Terrace Location Program), was developed to provide multiple terrace layout options using digital elevation model (DEM) and geographic information systems (GIS). Development of a terrace system is complicated by the time-intensive manual ...

Storyline Visualization: A Compelling Way to Understand Patterns over Time and Space

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2017-10-16

Storyline visualization is a compelling way to understand patterns over time and space. Much effort has been spent developing efficient and aesthetically pleasing layout optimization algorithms. But what if those algorithms are optimizing the wrong things? To answer this question, we conducted a design study with different storyline layout algorithms. We found that users with our new design principles for storyline visualization outperform existing methods.

The constraints satisfaction problem approach in the design of an architectural functional layout

NASA Astrophysics Data System (ADS)

Zawidzki, Machi; Tateyama, Kazuyoshi; Nishikawa, Ikuko

2011-09-01

A design support system with a new strategy for finding the optimal functional configurations of rooms for architectural layouts is presented. A set of configurations satisfying given constraints is generated and ranked according to multiple objectives. The method can be applied to problems in architectural practice, urban or graphic design-wherever allocation of related geometrical elements of known shape is optimized. Although the methodology is shown using simplified examples-a single story residential building with two apartments each having two rooms-the results resemble realistic functional layouts. One example of a practical size problem of a layout of three apartments with a total of 20 rooms is demonstrated, where the generated solution can be used as a base for a realistic architectural blueprint. The discretization of design space is discussed, followed by application of a backtrack search algorithm used for generating a set of potentially 'good' room configurations. Next the solutions are classified by a machine learning method (FFN) as 'proper' or 'improper' according to the internal communication criteria. Examples of interactive ranking of the 'proper' configurations according to multiple criteria and choosing 'the best' ones are presented. The proposed framework is general and universal-the criteria, parameters and weights can be individually defined by a user and the search algorithm can be adjusted to a specific problem.

Design and fabrication of a duoplasmatron extraction geometry and LEBT for the LANSCE H{sup +} RFQ project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fortgang, C. M., E-mail: cfortgang@lanl.gov; Batygin, Y. K.; Draganic, I. N.

The 750-keV H{sup +} Cockcroft-Walton at LANSCE will be replaced with a recently fabricated 4-rod Radio Frequency Quadrupole (RFQ) with injection energy of 35 keV. The existing duoplasmatron source extraction optics need to be modified to produce up to 35 mA of H{sup +} current with an emittance <0.02 π-cm-mrad (rms, norm) for injection into the RFQ. Parts for the new source have been fabricated and assembly is in process. We will use the existing duoplasmatron source with a newly designed extraction system and low energy beam transport (LEBT) for beam injection into the RFQ. In addition to source modifications,more » we need a new LEBT for transport and matching into the RFQ. The LEBT uses two magnetic solenoids with enough drift space between them to accommodate diagnostics and a beam deflector. The LEBT is designed to work over a range of space-charge neutralized currents and emittances. The LEBT is optimized in the sense that it minimizes the beam size in both solenoids for a point design of a given neutralized current and emittance. Special attention has been given to estimating emittance growth due to source extraction optics and solenoid aberrations. Examples of source-to-RFQ matching and emittance growth (due to both non-linear space charge and solenoid aberrations) are presented over a range of currents and emittances about the design point. A mechanical layout drawing will be presented along with the status of the source and LEBT, design, and fabrication.« less

An optimization tool for satellite equipment layout

NASA Astrophysics Data System (ADS)

Qin, Zheng; Liang, Yan-gang; Zhou, Jian-ping

2018-01-01

Selection of the satellite equipment layout with performance constraints is a complex task which can be viewed as a constrained multi-objective optimization and a multiple criteria decision making problem. The layout design of a satellite cabin involves the process of locating the required equipment in a limited space, thereby satisfying various behavioral constraints of the interior and exterior environments. The layout optimization of satellite cabin in this paper includes the C.G. offset, the moments of inertia and the space debris impact risk of the system, of which the impact risk index is developed to quantify the risk to a satellite cabin of coming into contact with space debris. In this paper an optimization tool for the integration of CAD software as well as the optimization algorithms is presented, which is developed to automatically find solutions for a three-dimensional layout of equipment in satellite. The effectiveness of the tool is also demonstrated by applying to the layout optimization of a satellite platform.

Layout finishing of a 28nm, 3 billions transistors, multi-core processor

NASA Astrophysics Data System (ADS)

Morey-Chaisemartin, Philippe; Beisser, Eric

2013-06-01

Designing a fully new 256 cores processor is a great challenge for a fabless startup. In addition to all architecture, functionalities and timing issues, the layout by itself is a bottleneck due to all the process constraints of a 28nm technology. As developers of advanced layout finishing solutions, we were involved in the design flow of this huge chip with its 3 billions transistors. We had to face the issue of dummy patterns instantiation with respect to design constraints. All the design rules to generate the "dummies" are clearly defined in the Design Rule Manual, and some automatic procedures are provided by the foundry itself, but these routines don't take care of the designer requests. Such a chip, embeds both digital parts and analog modules for clock and power management. These two different type of designs have each their own set of constraints. In both cases, the insertion of dummies should not introduce unexpected variations leading to malfunctions. For example, on digital parts were signal race conditions are critical on long wires or bus, introduction of uncontrolled parasitic along these nets are highly critical. For analog devices such as high frequency and high sensitivity comparators, the exact symmetry of the two parts of a current mirror generator should be guaranteed. Thanks to the easily customizable features of our dummies insertion tool, we were able to configure it in order to meet all the designer requirements as well as the process constraints. This paper will present all these advanced key features as well as the layout tricks used to fulfill all requirements.

14 CFR Appendix A to Part 158 - Assurances

Code of Federal Regulations, 2013 CFR

2013-01-01

... State and local laws and regulations. 4. Environmental, airspace and airport layout plan requirements... appropriate airspace finding has been made; and (c) The FAA Airport Layout Plan with respect to the project... airport design, construction and equipment standards and specifications contained in advisory circulars...

14 CFR Appendix A to Part 158 - Assurances

Code of Federal Regulations, 2011 CFR

2011-01-01

... State and local laws and regulations. 4. Environmental, airspace and airport layout plan requirements... appropriate airspace finding has been made; and (c) The FAA Airport Layout Plan with respect to the project... airport design, construction and equipment standards and specifications contained in advisory circulars...

14 CFR Appendix A to Part 158 - Assurances

Code of Federal Regulations, 2010 CFR

2010-01-01

... State and local laws and regulations. 4. Environmental, airspace and airport layout plan requirements... appropriate airspace finding has been made; and (c) The FAA Airport Layout Plan with respect to the project... airport design, construction and equipment standards and specifications contained in advisory circulars...

14 CFR Appendix A to Part 158 - Assurances

Code of Federal Regulations, 2014 CFR

2014-01-01

... State and local laws and regulations. 4. Environmental, airspace and airport layout plan requirements... appropriate airspace finding has been made; and (c) The FAA Airport Layout Plan with respect to the project... airport design, construction and equipment standards and specifications contained in advisory circulars...

14 CFR Appendix A to Part 158 - Assurances

Code of Federal Regulations, 2012 CFR

2012-01-01

... State and local laws and regulations. 4. Environmental, airspace and airport layout plan requirements... appropriate airspace finding has been made; and (c) The FAA Airport Layout Plan with respect to the project... airport design, construction and equipment standards and specifications contained in advisory circulars...

The Methodology of Interactive Parametric Modelling of Construction Site Facilities in BIM Environment

NASA Astrophysics Data System (ADS)

Kozlovská, Mária; Čabala, Jozef; Struková, Zuzana

2014-11-01

Information technology is becoming a strong tool in different industries, including construction. The recent trend of buildings designing is leading up to creation of the most comprehensive virtual building model (Building Information Model) in order to solve all the problems relating to the project as early as in the designing phase. Building information modelling is a new way of approaching to the design of building projects documentation. Currently, the building site layout as a part of the building design documents has a very little support in the BIM environment. Recently, the research of designing the construction process conditions has centred on improvement of general practice in planning and on new approaches to construction site layout planning. The state of art in field of designing the construction process conditions indicated an unexplored problem related to connection of knowledge system with construction site facilities (CSF) layout through interactive modelling. The goal of the paper is to present the methodology for execution of 3D construction site facility allocation model (3D CSF-IAM), based on principles of parametric and interactive modelling.

Selecting a proper design period for heliostat field layout optimization using Campo code

NASA Astrophysics Data System (ADS)

Saghafifar, Mohammad; Gadalla, Mohamed

2016-09-01

In this paper, different approaches are considered to calculate the cosine factor which is utilized in Campo code to expand the heliostat field layout and maximize its annual thermal output. Furthermore, three heliostat fields containing different number of mirrors are taken into consideration. Cosine factor is determined by considering instantaneous and time-average approaches. For instantaneous method, different design days and design hours are selected. For the time average method, daily time average, monthly time average, seasonally time average, and yearly time averaged cosine factor determinations are considered. Results indicate that instantaneous methods are more appropriate for small scale heliostat field optimization. Consequently, it is proposed to consider the design period as the second design variable to ensure the best outcome. For medium and large scale heliostat fields, selecting an appropriate design period is more important. Therefore, it is more reliable to select one of the recommended time average methods to optimize the field layout. Optimum annual weighted efficiency for heliostat fields (small, medium, and large) containing 350, 1460, and 3450 mirrors are 66.14%, 60.87%, and 54.04%, respectively.

Machining fixture layout optimization using particle swarm optimization algorithm

NASA Astrophysics Data System (ADS)

Dou, Jianping; Wang, Xingsong; Wang, Lei

2011-05-01

Optimization of fixture layout (locator and clamp locations) is critical to reduce geometric error of the workpiece during machining process. In this paper, the application of particle swarm optimization (PSO) algorithm is presented to minimize the workpiece deformation in the machining region. A PSO based approach is developed to optimize fixture layout through integrating ANSYS parametric design language (APDL) of finite element analysis to compute the objective function for a given fixture layout. Particle library approach is used to decrease the total computation time. The computational experiment of 2D case shows that the numbers of function evaluations are decreased about 96%. Case study illustrates the effectiveness and efficiency of the PSO based optimization approach.

Improved arrayed-waveguide-grating layout avoiding systematic phase errors.

PubMed

Ismail, Nur; Sun, Fei; Sengo, Gabriel; Wörhoff, Kerstin; Driessen, Alfred; de Ridder, René M; Pollnau, Markus

2011-04-25

We present a detailed description of an improved arrayed-waveguide-grating (AWG) layout for both, low and high diffraction orders. The novel layout presents identical bends across the entire array; in this way systematic phase errors arising from different bends that are inherent to conventional AWG designs are completely eliminated. In addition, for high-order AWGs our design results in more than 50% reduction of the occupied area on the wafer. We present an experimental characterization of a low-order device fabricated according to this geometry. The device has a resolution of 5.5 nm, low intrinsic losses (< 2 dB) in the wavelength region of interest for the application, and is polarization insensitive over a wide spectral range of 215 nm.

Optimization of self-aligned double patterning (SADP)-compliant layout designs using pattern matching for sub-20nm metal routing

NASA Astrophysics Data System (ADS)

Wang, Lynn T.-N.; Schroeder, Uwe Paul; Madhavan, Sriram

2017-03-01

A pattern-based methodology for optimizing SADP-compliant layout designs is developed based on identifying cut mask patterns and replacing them with pre-characterized fixing solutions. A pattern-based library of difficult-tomanufacture cut patterns with pre-characterized fixing solutions is built. A pattern-based engine searches for matching patterns in the decomposed layouts. When a match is found, the engine opportunistically replaces the detected pattern with a pre-characterized fixing solution. The methodology was demonstrated on a 7nm routed metal2 block. A small library of 30 cut patterns increased the number of more manufacturable cuts by 38% and metal-via enclosure by 13% with a small parasitic capacitance impact of 0.3%.

An integrated approach for facilities planning by ELECTRE method

NASA Astrophysics Data System (ADS)

Elbishari, E. M. Y.; Hazza, M. H. F. Al; Adesta, E. Y. T.; Rahman, Nur Salihah Binti Abdul

2018-01-01

Facility planning is concerned with the design, layout, and accommodation of people, machines and activities of a system. Most of the researchers try to investigate the production area layout and the related facilities. However, few of them try to investigate the relationship between the production space and its relationship with service departments. The aim of this research to is to integrate different approaches in order to evaluate, analyse and select the best facilities planning method that able to explain the relationship between the production area and other supporting departments and its effect on human efforts. To achieve the objective of this research two different approaches have been integrated: Apple’s layout procedure as one of the effective tools in planning factories, ELECTRE method as one of the Multi Criteria Decision Making methods (MCDM) to minimize the risk of getting poor facilities planning. Dalia industries have been selected as a case study to implement our integration the factory have been divided two main different area: the whole facility (layout A), and the manufacturing area (layout B). This article will be concerned with the manufacturing area layout (Layout B). After analysing the data gathered, the manufacturing area was divided into 10 activities. There are five factors that the alternative were compared upon which are: Inter department satisfactory level, total distance travelled for workers, total distance travelled for the product, total time travelled for the workers, and total time travelled for the product. Three different layout alternatives have been developed in addition to the original layouts. Apple’s layout procedure was used to study and evaluate the different alternatives layouts, the study and evaluation of the layouts was done by calculating scores for each of the factors. After obtaining the scores from evaluating the layouts, ELECTRE method was used to compare the proposed alternatives with each other and with the existing layout; ELECTRE compares the alternatives based on their concordance and discordance indices. The alternatives were ranked from best to worst where regarding to the layouts concerned with the manufacturing area B.4 is the best alternative.

Optimization of municipal pressure pumping station layout and sewage pipe network design

NASA Astrophysics Data System (ADS)

Tian, Jiandong; Cheng, Jilin; Gong, Yi

2018-03-01

Accelerated urbanization places extraordinary demands on sewer networks; thus optimization research to improve the design of these systems has practical significance. In this article, a subsystem nonlinear programming model is developed to optimize pumping station layout and sewage pipe network design. The subsystem model is expanded into a large-scale complex nonlinear programming system model to find the minimum total annual cost of the pumping station and network of all pipe segments. A comparative analysis is conducted using the sewage network in Taizhou City, China, as an example. The proposed method demonstrated that significant cost savings could have been realized if the studied system had been optimized using the techniques described in this article. Therefore, the method has practical value for optimizing urban sewage projects and provides a reference for theoretical research on optimization of urban drainage pumping station layouts.

Loss analysis and optimum design of a highly efficient and compact CMOS DC–DC converter with novel transistor layout using 60 nm multipillar-type vertical body channel MOSFET

NASA Astrophysics Data System (ADS)

Itoh, Kazuki; Endoh, Tetsuo

2018-04-01

In this paper, we present a novel transistor layout of multi pillar-type vertical body-channel (BC) MOSFET for cascode power switches for improving the efficiency and compactness of CMOS DC–DC converters. The proposed layout features a stacked and multifingered layout to suppress the loss due to parasitic components such as diffusion resistance and contact resistance. In addition, the loss of each MOSFET, which configures cascode power switches, is analyzed, and it is revealed that the total optimum gate width and loss with the high-side (HS) n-type MOSFET topology are 27 and 16% smaller than those with the HS p-type MOSFET topology, respectively. Moreover, a circuit simulation of 2.0 to 0.8 V, 100 MHz CMOS DC–DC converters with the proposed layout is carried out by using experimentally extracted models of BSIM4 60 nm vertical BC MOSFETs. The peak efficiency of the HS n-type MOSFET converter with the proposed layout is 90.1%, which is 6.0% higher than that with the conventional layout.

Generating Multi-Destination Maps.

PubMed

Zhang, Junsong; Fan, Jiepeng; Luo, Zhenshan

2017-08-01

Multi-destination maps are a kind of navigation maps aimed to guide visitors to multiple destinations within a region, which can be of great help to urban visitors. However, they have not been developed in the current online map service. To address this issue, we introduce a novel layout model designed especially for generating multi-destination maps, which considers the global and local layout of a multi-destination map. We model the layout problem as a graph drawing that satisfies a set of hard and soft constraints. In the global layout phase, we balance the scale factor between ROIs. In the local layout phase, we make all edges have good visibility and optimize the map layout to preserve the relative length and angle of roads. We also propose a perturbation-based optimization method to find an optimal layout in the complex solution space. The multi-destination maps generated by our system are potential feasible on the modern mobile devices and our result can show an overview and a detail view of the whole map at the same time. In addition, we perform a user study to evaluate the effectiveness of our method, and the results prove that the multi-destination maps achieve our goals well.

Automated solar collector installation design

DOEpatents

Wayne, Gary; Frumkin, Alexander; Zaydman, Michael; Lehman, Scott; Brenner, Jules

2014-08-26

Embodiments may include systems and methods to create and edit a representation of a worksite, to create various data objects, to classify such objects as various types of pre-defined "features" with attendant properties and layout constraints. As part of or in addition to classification, an embodiment may include systems and methods to create, associate, and edit intrinsic and extrinsic properties to these objects. A design engine may apply of design rules to the features described above to generate one or more solar collectors installation design alternatives, including generation of on-screen and/or paper representations of the physical layout or arrangement of the one or more design alternatives.

Change of the layout of an office of a metallurgical company: simple projects, big solutions.

PubMed

Duarte, Luiz Carlos da Silva; Eckhardt, Moacir; da Motta, Giordano Paulo

2012-01-01

The posture, a good organization and the proper layout of the environment and workplaces have a positive influence on the income of an employee. To develop the work it is used a methodology that addressed the study phases of the theory involving the subject, description of the current situation, preparation of conceptions, choice of design, implementation and reporting of results. Through the project of "Change of the layout of an office of a metallurgical company" there was an intervention in these reported aspects providing improvements in the office, regarding ergonomic, layout, workplace and lighting issues, bringing welfare to the official, with the intent to improve its performance within the company and facilitating its actions, as the company's customer service. The results provided improvements in layout, in the workplace and especially in comfort for the human resources that perform their activities.

ManiWordle: providing flexible control over Wordle.

PubMed

Koh, Kyle; Lee, Bongshin; Kim, Bohyoung; Seo, Jinwook

2010-01-01

Among the multifarious tag-clouding techniques, Wordle stands out to the community by providing an aesthetic layout, eliciting the emergence of the participatory culture and usage of tag-clouding in the artistic creations. In this paper, we introduce ManiWordle, a Wordle-based visualization tool that revamps interactions with the layout by supporting custom manipulations. ManiWordle allows people to manipulate typography, color, and composition not only for the layout as a whole, but also for the individual words, enabling them to have better control over the layout result. We first describe our design rationale along with the interaction techniques for tweaking the layout. We then present the results both from the preliminary usability study and from the comparative study between ManiWordle and Wordle. The results suggest that ManiWordle provides higher user satisfaction and an efficient method of creating the desired "art work," harnessing the power behind the ever-increasing popularity of Wordle.

DeDaL: Cytoscape 3 app for producing and morphing data-driven and structure-driven network layouts.

PubMed

Czerwinska, Urszula; Calzone, Laurence; Barillot, Emmanuel; Zinovyev, Andrei

2015-08-14

Visualization and analysis of molecular profiling data together with biological networks are able to provide new mechanistic insights into biological functions. Currently, it is possible to visualize high-throughput data on top of pre-defined network layouts, but they are not always adapted to a given data analysis task. A network layout based simultaneously on the network structure and the associated multidimensional data might be advantageous for data visualization and analysis in some cases. We developed a Cytoscape app, which allows constructing biological network layouts based on the data from molecular profiles imported as values of node attributes. DeDaL is a Cytoscape 3 app, which uses linear and non-linear algorithms of dimension reduction to produce data-driven network layouts based on multidimensional data (typically gene expression). DeDaL implements several data pre-processing and layout post-processing steps such as continuous morphing between two arbitrary network layouts and aligning one network layout with respect to another one by rotating and mirroring. The combination of all these functionalities facilitates the creation of insightful network layouts representing both structural network features and correlation patterns in multivariate data. We demonstrate the added value of applying DeDaL in several practical applications, including an example of a large protein-protein interaction network. DeDaL is a convenient tool for applying data dimensionality reduction methods and for designing insightful data displays based on data-driven layouts of biological networks, built within Cytoscape environment. DeDaL is freely available for downloading at http://bioinfo-out.curie.fr/projects/dedal/.

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and... the end of this part illustrating the basic layout. All positioning, spacing, type sizes, and line... calculated for heating Region IV for the standardized design heating requirement nearest the capacity...

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and... the end of this part illustrating the basic layout. All positioning, spacing, type sizes, and line... calculated for heating Region IV for the standardized design heating requirement nearest the capacity...

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Code of Federal Regulations, 2013 CFR

2013-01-01

... pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and... end of this part illustrating the basic layout. All positioning, spacing, type sizes, and line widths... calculated for heating Region IV for the standardized design heating requirement nearest the capacity...

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Code of Federal Regulations, 2012 CFR

2012-01-01

... pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and... the end of this part illustrating the basic layout. All positioning, spacing, type sizes, and line... calculated for heating Region IV for the standardized design heating requirement nearest the capacity...

Computer visualizations in engineering applications

NASA Astrophysics Data System (ADS)

Bills, K. C.

The use of computerized simulations of various robotic tasks via IGRIP software is reported. The projects include underwater activities demonstrating clean up of a quarry; time study of methods to store waste drums inside a facility; design walk-through of a new facility; plant layout flyover; and conceptual development and layout of new mechanisms.

Precision Sheet Metal. Progress Record and Theory Outline.

ERIC Educational Resources Information Center

Connecticut State Dept. of Education, Hartford. Div. of Vocational-Technical Schools.

This combination progress record and course outline is designed for use by individuals teaching a course in precision sheet metal. Included among the topics addressed in the course are the following: employment opportunities in metalworking, measurement and layout, orthographic projection, precision sheet metal drafting, simple layout, hand tools,…

Design and simulation of integration system between automated material handling system and manufacturing layout in the automotive assembly line

NASA Astrophysics Data System (ADS)

Seha, S.; Zamberi, J.; Fairu, A. J.

2017-10-01

Material handling system (MHS) is an important part for the productivity plant and has recognized as an integral part of today’s manufacturing system. Currently, MHS has growth tremendously with its technology and equipment type. Based on the case study observation, the issue involving material handling system contribute to the reduction of production efficiency. This paper aims to propose a new design of integration between material handling and manufacturing layout by investigating the influences of layout and material handling system. A method approach tool using Delmia Quest software is introduced and the simulation result is used to assess the influences of the integration between material handling system and manufacturing layout in the performance of automotive assembly line. The result show, the production of assembly line output increases more than 31% from the current system. The source throughput rate average value went up to 252 units per working hour in model 3 and show the effectiveness of the pick-to-light system as efficient storage equipment. Thus, overall result shows, the application of AGV and the pick-to-light system gave a large significant effect in the automotive assembly line. Moreover, the change of layout also shows a large significant improvement to the performance.

Solving a mathematical model integrating unequal-area facilities layout and part scheduling in a cellular manufacturing system by a genetic algorithm.

PubMed

Ebrahimi, Ahmad; Kia, Reza; Komijan, Alireza Rashidi

2016-01-01

In this article, a novel integrated mixed-integer nonlinear programming model is presented for designing a cellular manufacturing system (CMS) considering machine layout and part scheduling problems simultaneously as interrelated decisions. The integrated CMS model is formulated to incorporate several design features including part due date, material handling time, operation sequence, processing time, an intra-cell layout of unequal-area facilities, and part scheduling. The objective function is to minimize makespan, tardiness penalties, and material handling costs of inter-cell and intra-cell movements. Two numerical examples are solved by the Lingo software to illustrate the results obtained by the incorporated features. In order to assess the effects and importance of integration of machine layout and part scheduling in designing a CMS, two approaches, sequentially and concurrent are investigated and the improvement resulted from a concurrent approach is revealed. Also, due to the NP-hardness of the integrated model, an efficient genetic algorithm is designed. As a consequence, computational results of this study indicate that the best solutions found by GA are better than the solutions found by B&B in much less time for both sequential and concurrent approaches. Moreover, the comparisons between the objective function values (OFVs) obtained by sequential and concurrent approaches demonstrate that the OFV improvement is averagely around 17 % by GA and 14 % by B&B.

Human Factors Evaluations of Two-Dimensional Spacecraft Conceptual Layouts

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Toups, Larry D.; Rudisill, Marianne

2010-01-01

Much of the human factors work done in support of the NASA Constellation lunar program has been with low fidelity mockups. These volumetric replicas of the future lunar spacecraft allow researchers to insert test subjects from the engineering and astronaut population and evaluate the vehicle design as the test subjects perform simulations of various operational tasks. However, lunar outpost designs must be evaluated without the use of mockups, creating a need for evaluation tools that can be performed on two-dimension conceptual spacecraft layouts, such as floor plans. A tool based on the Cooper- Harper scale was developed and applied to one lunar scenario, enabling engineers to select between two competing floor plan layouts. Keywords: Constellation, human factors, tools, processes, habitat, outpost, Net Habitable Volume, Cooper-Harper.

Analysis of crew functions as an aid in Space Station interior layout

NASA Technical Reports Server (NTRS)

Steinberg, A. L.; Tullis, Thomas S.; Bied, Barbra

1986-01-01

The Space Station must be designed to facilitate all of the functions that its crew will perform, both on-duty and off-duty, as efficiently and comfortably as possible. This paper examines the functions to be performed by the Space Station crew in order to make inferences about the design of an interior layout that optimizes crew productivity. Twenty-seven crew functions were defined, as well as five criteria for assessing relationships among all pairs of those functions. Hierarchical clustering and multidimensional scaling techniques were used to visually summarize the relationships. A key result was the identification of two dimensions for describing the configuration of crew functions: 'Private-Public' and 'Group-Individual'. Seven specific recommendations for Space Station interior layout were derived from the analyses.

Layout and Design in "Real Life"

ERIC Educational Resources Information Center

Bremer, Janet; Stocker, Donald

2004-01-01

Educators are required to combine their expertise and allow students to explore the different areas by using the method of collaboration in which teachers from different disciplines will create an environment where each will use their expert skills. The collaboration of a computer teacher with an art teacher resulted in the creation of Layout and…

The Influence of Hierarchy and Layout Geometry in the Design of Learning Spaces

ERIC Educational Resources Information Center

Smith, Charlie

2017-01-01

For a number of years, higher education has moved away from didactic teaching toward collaborative and self-directed learning. This paper discusses how the configuration and spatial geometry of learning spaces influences engagement and interaction, with a particular focus on hierarchies between people within the space. Layouts, presented as…

You Be the Judge: Newspaper Advertising Layout.

ERIC Educational Resources Information Center

Koeninger, Jimmy G.

The learning package is designed to provide the marketing educator with a culminating activity for an instructional unit focusing on advertising layout principles and procedures. It is to be used in conjunction with 35mm slides of newspaper advertisements, which the student views and rates in comparison with the ratings of a panel of experts. A…

Automated Generation of Finite-Element Meshes for Aircraft Conceptual Design

NASA Technical Reports Server (NTRS)

Li, Wu; Robinson, Jay

2016-01-01

This paper presents a novel approach for automated generation of fully connected finite-element meshes for all internal structural components and skins of a given wing-body geometry model, controlled by a few conceptual-level structural layout parameters. Internal structural components include spars, ribs, frames, and bulkheads. Structural layout parameters include spar/rib locations in wing chordwise/spanwise direction and frame/bulkhead locations in longitudinal direction. A simple shell thickness optimization problem with two load conditions is used to verify versatility and robustness of the automated meshing process. The automation process is implemented in ModelCenter starting from an OpenVSP geometry and ending with a NASTRAN 200 solution. One subsonic configuration and one supersonic configuration are used for numerical verification. Two different structural layouts are constructed for each configuration and five finite-element meshes of different sizes are generated for each layout. The paper includes various comparisons of solutions of 20 thickness optimization problems, as well as discussions on how the optimal solutions are affected by the stress constraint bound and the initial guess of design variables.

Standard cell electrical and physical variability analysis based on automatic physical measurement for design-for-manufacturing purposes

NASA Astrophysics Data System (ADS)

Shauly, Eitan; Parag, Allon; Khmaisy, Hafez; Krispil, Uri; Adan, Ofer; Levi, Shimon; Latinski, Sergey; Schwarzband, Ishai; Rotstein, Israel

2011-04-01

A fully automated system for process variability analysis of high density standard cell was developed. The system consists of layout analysis with device mapping: device type, location, configuration and more. The mapping step was created by a simple DRC run-set. This database was then used as an input for choosing locations for SEM images and for specific layout parameter extraction, used by SPICE simulation. This method was used to analyze large arrays of standard cell blocks, manufactured using Tower TS013LV (Low Voltage for high-speed applications) Platforms. Variability of different physical parameters like and like Lgate, Line-width-roughness and more as well as of electrical parameters like drive current (Ion), off current (Ioff) were calculated and statistically analyzed, in order to understand the variability root cause. Comparison between transistors having the same W/L but with different layout configurations and different layout environments (around the transistor) was made in terms of performances as well as process variability. We successfully defined "robust" and "less-robust" transistors configurations, and updated guidelines for Design-for-Manufacturing (DfM).

Realizing improved patient care through human-centered operating room design: a human factors methodology for observing flow disruptions in the cardiothoracic operating room.

PubMed

Palmer, Gary; Abernathy, James H; Swinton, Greg; Allison, David; Greenstein, Joel; Shappell, Scott; Juang, Kevin; Reeves, Scott T

2013-11-01

Human factors engineering has allowed a systematic approach to the evaluation of adverse events in a multitude of high-stake industries. This study sought to develop an initial methodology for identifying and classifying flow disruptions in the cardiac operating room (OR). Two industrial engineers with expertise in human factors workflow disruptions observed 10 cardiac operations from the moment the patient entered the OR to the time they left for the intensive care unit. Each disruption was fully documented on an architectural layout of the OR suite and time-stamped during each phase of surgery (preoperative [before incision], operative [incision to skin closure], and postoperative [skin closure until the patient leaves the OR]) to synchronize flow disruptions between the two observers. These disruptions were then categorized. The two observers made a total of 1,158 observations. After the elimination of duplicate observations, a total of 1,080 observations remained to be analyzed. These disruptions were distributed into six categories such as communication, usability, physical layout, environmental hazards, general interruptions, and equipment failures. They were further organized into 33 subcategories. The most common disruptions were related to OR layout and design (33%). By using the detailed architectural diagrams, the authors were able to clearly demonstrate for the first time the unique role that OR design and equipment layout has on the generation of physical layout flow disruptions. Most importantly, the authors have developed a robust taxonomy to describe the flow disruptions encountered in a cardiac OR, which can be used for future research and patient safety improvements.

How do typographical factors affect reading text and comprehension performance in Arabic?

PubMed

Ganayim, Deia; Ibrahim, Raphiq

2013-04-01

The objective of this study was to establish basic reading performance that could lead to useful design recommendations for print display text formats and layouts for the improvement of reading and comprehension performance of print text, such as academic writings, books, and newspapers, of Arabic language. Readability of English print text has been shown to be influenced by a number of typographical variables, including interline spacing, column setting and line length, and so on.Therefore, it is very important to improve the reading efficiency and satisfaction of print text reading and comprehension by following simple design guidelines. Most existing research on readability of print text is oriented to build guidelines for designing English texts rather than Arabic. However, guidelines built for English script cannot be simply applied for Arabic script because of orthographic differences. In the current study, manipulating interline spacing and column setting and line length generated nine text layouts. The reading and comprehension performance of 210 native Arab students assigned randomly to the different text layouts was compared. Results showed that the use of multicolumn setting (with medium or short line length) affected comprehension achievement but not reading and comprehension speed. Participants' comprehension scores were better for the single-column (with long line length) than for the multicolumn setting. However, no effect was found for interline spacing. The recommendations for appropriate print text format and layout in Arabic language based on the results of objective measures facilitating reading and comprehension performance is a single-column (with long line length) layout with no relevance of the interline spacing.

A smart way to identify and extract repeated patterns of a layout

NASA Astrophysics Data System (ADS)

Wei, Fang; Gu, Tingting; Chu, Zhihao; Zhang, Chenming; Chen, Han; Zhu, Jun; Hu, Xinyi; Du, Chunshan; Wan, Qijian; Liu, Zhengfang

2018-03-01

As integrated circuits (IC) technology moves forward, manufacturing process is facing more and more challenges. Optical proximity correction (OPC) has been playing an important role in the whole manufacturing process. In the deep sub-micron technology, OPC engineers not only need to guarantee the layout designs to be manufacturable but also take a more precise control of the critical patterns to ensure a high performance circuit. One of the tasks that would like to be performed is the consistency checking as the identical patterns under identical context should have identical OPC results in theory, like SRAM regions. Consistency checking is essentially a technique of repeated patterns identification, extraction and derived patterns (i.e. OPC results) comparison. The layout passing to the OPC team may not have enough design hierarchical information either because the original designs may have undergone several layout processing steps or some other unknown reasons. This paper presents a generic way to identify and extract repeated layout structures in SRAM regions purely based on layout pattern analysis through Calibre Pattern Matching and Calibre equation-based DRC (eqDRC). Without Pattern Matching and eqDRC, it will take lots of effort to manually get it done by trial and error, it is almost impossible to automate the pattern analysis process. Combining Pattern Matching and eqDRC opens a new way to implement this flow. The repeated patterns must have some fundamental features for measurement of pitches in the horizontal and vertical direction separately by Calibre eqDRC and meanwhile can be a helper to generate some anchor points which will be the starting points for Pattern Matching to capture patterns. The informative statistical report from the pattern search tells the match counts individually for each patterns captured. Experiment shows that this is a smart way of identifying and extracting repeated structures effectively. The OPC results are the derived layers on these repeated structures, by running pattern search using design layers as pattern layers and OPC results as marker layers, it is an easy job to compare the consistency.

Human factors issues and approaches in the spatial layout of a space station control room, including the use of virtual reality as a design analysis tool

NASA Technical Reports Server (NTRS)

Hale, Joseph P., II

1994-01-01

Human Factors Engineering support was provided for the 30% design review of the late Space Station Freedom Payload Control Area (PCA). The PCA was to be the payload operations control room, analogous to the Spacelab Payload Operations Control Center (POCC). This effort began with a systematic collection and refinement of the relevant requirements driving the spatial layout of the consoles and PCA. This information was used as input for specialized human factors analytical tools and techniques in the design and design analysis activities. Design concepts and configuration options were developed and reviewed using sketches, 2-D Computer-Aided Design (CAD) drawings, and immersive Virtual Reality (VR) mockups.

A multiple-drawer medication layout problem in automated dispensing cabinets.

PubMed

Pazour, Jennifer A; Meller, Russell D

2012-12-01

In this paper we investigate the problem of locating medications in automated dispensing cabinets (ADCs) to minimize human selection errors. We formulate the multiple-drawer medication layout problem and show that the problem can be formulated as a quadratic assignment problem. As a way to evaluate various medication layouts, we develop a similarity rating for medication pairs. To solve industry-sized problem instances, we develop a heuristic approach. We use hospital ADC transaction data to conduct a computational experiment to test the performance of our developed heuristics, to demonstrate how our approach can aid in ADC design trade-offs, and to illustrate the potential improvements that can be made when applying an analytical process to the multiple-drawer medication layout problem. Finally, we present conclusions and future research directions.

Application of a GPU-Assisted Maxwell Code to Electromagnetic Wave Propagation in ITER

NASA Astrophysics Data System (ADS)

Kubota, S.; Peebles, W. A.; Woodbury, D.; Johnson, I.; Zolfaghari, A.

2014-10-01

The Low Field Side Reflectometer (LSFR) on ITER is envisioned to provide capabilities for electron density profile and fluctuations measurements in both the plasma core and edge. The current design for the Equatorial Port Plug 11 (EPP11) employs seven monostatic antennas for use with both fixed-frequency and swept-frequency systems. The present work examines the characteristics of this layout using the 3-D version of the GPU-Assisted Maxwell Code (GAMC-3D). Previous studies in this area were performed with either 2-D full wave codes or 3-D ray- and beam-tracing. GAMC-3D is based on the FDTD method and can be run with either a fixed-frequency or modulated (e.g. FMCW) source, and with either a stationary or moving target (e.g. Doppler backscattering). The code is designed to run on a single NVIDIA Tesla GPU accelerator, and utilizes a technique based on the moving window method to overcome the size limitation of the onboard memory. Effects such as beam drift, linear mode conversion, and diffraction/scattering will be examined. Comparisons will be made with beam-tracing calculations using the complex eikonal method. Supported by U.S. DoE Grants DE-FG02-99ER54527 and DE-AC02-09CH11466, and the DoE SULI Program at PPPL.

Process simulation during the design process makes the difference: process simulations applied to a traditional design.

PubMed

Traversari, Roberto; Goedhart, Rien; Schraagen, Jan Maarten

2013-01-01

The objective is evaluation of a traditionally designed operating room using simulation of various surgical workflows. A literature search showed that there is no evidence for an optimal operating room layout regarding the position and size of an ultraclean ventilation (UCV) canopy with a separate preparation room for laying out instruments and in which patients are induced in the operating room itself. Neither was literature found reporting on process simulation being used for this application. Many technical guidelines and designs have mainly evolved over time, and there is no evidence on whether the proposed measures are also effective for the optimization of the layout for workflows. The study was conducted by applying observational techniques to simulated typical surgical procedures. Process simulations which included complete surgical teams and equipment required for the intervention were carried out for four typical interventions. Four observers used a form to record conflicts with the clean area boundaries and the height of the supply bridge. Preferences for particular layouts were discussed with the surgical team after each simulated procedure. We established that a clean area measuring 3 × 3 m and a supply bridge height of 2.05 m was satisfactory for most situations, provided a movable operation table is used. The only cases in which conflicts with the supply bridge were observed were during the use of a surgical robot (Da Vinci) and a surgical microscope. During multiple trauma interventions, bottlenecks regarding the dimensions of the clean area will probably arise. The process simulation of four typical interventions has led to significantly different operating room layouts than were arrived at through the traditional design process. Evidence-based design, human factors, work environment, operating room, traditional design, process simulation, surgical workflowsPreferred Citation: Traversari, R., Goedhart, R., & Schraagen, J. M. (2013). Process simulation during the design process makes the difference: Process simulations applied to a traditional design. Health Environments Research & Design Journal 6(2), pp 58-76.

Compact, high-speed algorithm for laying out printed circuit board runs

NASA Astrophysics Data System (ADS)

Zapolotskiy, D. Y.

1985-09-01

A high speed printed circuit connection layout algorithm is described which was developed within the framework of an interactive system for designing two-sided printed circuit broads. For this reason, algorithm speed was considered, a priori, as a requirement equally as important as the inherent demand for minimizing circuit run lengths and the number of junction openings. This resulted from the fact that, in order to provide psychological man/machine compatibility in the design process, real-time dialog during the layout phase is possible only within limited time frames (on the order of several seconds) for each circuit run. The work was carried out for use on an ARM-R automated work site complex based on an SM-4 minicomputer with a 32K-word memory. This limited memory capacity heightened the demand for algorithm speed and also tightened data file structure and size requirements. The layout algorithm's design logic is analyzed. The structure and organization of the data files are described.

Consumer's Perception on Design and Layout of Consumer Medical Information Leaflets on Obesity and Lipid Lowering Drugs.

PubMed

Mathew, Elizabeth M; Rajiah, Kingston; Sharma, Krishana Kumar

2013-12-01

Printed education materials are often used to augment healthcare professional's verbal information to consumers so it serves as an important component of symptom management. They also enhance the teaching process and can be used by consumers as a home reference. This study was aimed to interpret consumers' perception on Consumer Medical Information Leaflets (CMILs) on obesity and lipid lowering drugs, on design and layout using the standard method such as Baker Able Leaflet Design (BALD). Convenience sampling was done. The study was conducted over a period of 3 years in community pharmacy settings in Tamil Nadu, India. The Consumer Medical Information Leaflets (CMILs) were randomly collected from different community pharmacies. Total of 19 CMILs which are commonly used by the consumers were collected and CMILs were assessed using BALD assessment tool Results: According to BALD assessment (46.28%) leaflets were rated as 'above standard' and (53.72) leaflets were rated as 'standard or poor' in layout and design since their scores were less than 25. This shows that this issue may be important from the patient's perspective, which may discourage patient from actually reading the CMILs. In India, generally CMILs are continued to be prepared in English and with higher proportion of consumers with English illiteracy. CMILs, which are prepared without taking consideration of reading level of consumers and proper layout and design, may not achieve the intended purpose. This is an important aspect that any company has to reckon while preparing leaflets and at least in some major local languages in which CMILs have to be prepared.

Print Reading, Layout and Fit-Up. Welding Module 2. Instructor's Guide.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This guide is intended to assist vocational educators in teaching a five-unit module in print reading, layout, and fit-up. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The following topics are covered in the module: reading basic prints and…

Yucca Mountain Project Subsurface Facilities Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. Linden; R.S. Saunders; R.J. Boutin

2002-11-19

Four units of the Topopah Springs formation (volcanic tuff) are considered for the proposed repository: the upper lithophysal, the middle non-lithophysal, the lower lithophysal, and the lower non-lithophysal. Yucca Mountain was recently designated the site for a proposed repository to dispose of spent nuclear fuel and high-level radioactive waste. Work is proceeding to advance the design of subsurface facilities to accommodate emplacing waste packages in the proposed repository. This paper summarized recent progress in the design of subsurface layout of the proposed repository. The original Site Recommendation (SR) concept for the subsurface design located the repository largely within the lowermore » lithophysal zone (approximately 73%) of the Topopah The Site Recommendation characterized area suitable for emplacement consisted of the primary upper block, the lower block and the southern upper block extension. The primary upper block accommodated the mandated 70,000 metric tons of heavy metal (MTHM) at a 1.45 kW/m hear heat load. Based on further study of the Site Recommendation concept, the proposed repository siting area footprint was modified to make maximum use of available site characterization data, and thus, reduce uncertainties associated with performance assessment. As a result of this study, a modified repository footprint has been proposed and is presently being review for acceptance by the DOE. A panel design concept was developed to reduce overall costs and reduce the overall emplacement schedule. This concept provides flexibility to adjust the proposed repository subsurface layout with time, as it makes it unnecessary to ''commit'' to development of a large single panel at the earliest stages of construction. A description of the underground layout configuration and influencing factors that affect the layout configuration are discussed in the report.« less

Analytical Tools for Functional Assessment of Architectural Layouts

NASA Astrophysics Data System (ADS)

Bąkowski, Jarosław

2017-10-01

Functional layout of the building, understood as a layout or set of the facility rooms (or groups of rooms) with a system of internal communication, creates an environment and a place of mutual relations between the occupants of the object. Achieving optimal (from the occupants’ point of view) spatial arrangement is possible through activities that often go beyond the stage of architectural design. Adopted in the architectural design, most often during trial and error process or on the basis of previous experience (evidence-based design), functional layout is subject to continuous evaluation and dynamic changing since the beginning of its use. Such verification of the occupancy phase allows to plan future, possible transformations, as well as to develop model solutions for use in other settings. In broader terms, the research hypothesis is to examine whether and how the collected datasets concerning the facility and its utilization can be used to develop methods for assessing functional layout of buildings. In other words, if it is possible to develop an objective method of assessing functional layouts basing on a set of buildings’ parameters: technical, technological and functional ones and whether the method allows developing a set of tools enhancing the design methodology of complex functional objects. By linking the design with the construction phase it is possible to build parametric models of functional layouts, especially in the context of sustainable design or lean design in every aspect: ecological (by reducing the property’s impact on environment), economic (by optimizing its cost) and social (through the implementation of high-performance work environment). Parameterization of size and functional connections of the facility become part of the analyses, as well as the element of model solutions. The “lean” approach means the process of analysis of the existing scheme and consequently - finding weak points as well as means for eliminating these defects. This approach, supplemented by the method of reverse engineering means that already in the design phase there is essential knowledge about the functioning of the facility. It is far beyond intuitive knowledge, based on the standards and specifications. In the scope of reverse engineering methods, the subject of the research is an audit of the product (i.e. architectural design, especially the built spatial layout) in order to determine exactly how it works. Information gained in this way is to help building a system for supporting decisions for preparing design solutions for future investments as well as the functional analysis itself becomes an essential part of the setting up building information process. The data are presented with graphical methods as networks of different factors between rooms. The direct analytical method for the setting is to determine the functional collision between users’ tracks, finding or indication of the shortest paths connecting analyzed rooms and finally to identify the optimal location of these rooms (each according to different factor). The measurement data are supplemented by the results of surveys conducted among users of hospitals, statistics and quantitative medical procedures performed in the test section of the hospital. The results of research are transferred and integrated with BIM system (building information modelling system), and included in the specifications of the IFC (Industry Foundation Classes), especially at the level of information on the relationship between the individual properties associated with elements (in the case of hospitals it may be information about the necessary connections with other rooms, access times from or to specific rooms, rooms utilization conditions, fire safety protection and conditions and many other). At the level of the BIM specification the model data are integrated at the BIM 6D (an extension of the model data with a range of functional analysis) or even BIM 7D (additional integration with systems used at the stage of operation and maintenance of the facility).

1D and 3D anthropometric data application on public transport vehicle layout and on oil and gas laboratories work environment design.

PubMed

Pastura, F C H; Guimarães, C P; Zamberlan, M C P; Cid, G L; Santos, V S; Streit, P; Paranhos, A G; Cobbe, R T; Cobbe, K T; Batista, D S

2012-01-01

The goal of this paper is to present 1D and 3D anthropometric data applied to two distinct design situations: one related to the interior layout of a public transport vehicle and another one related to oil and gas laboratories work environment design. On this study, the 1D anthropometric data were extracted from the Brazilian anthropometric database developed by INT and the 3D anthropometric data were obtained using a Cyberware 3D whole body scanner. A second purpose of this paper is to present the 3D human scanning data as a tool that can help designers on decision making.

Control centers design for ergonomics and safety.

PubMed

Quintana, Leonardo; Lizarazo, Cesar; Bernal, Oscar; Cordoba, Jorge; Arias, Claudia; Monroy, Magda; Cotrino, Carlos; Montoya, Olga

2012-01-01

This paper shows the general design conditions about ergonomics and safety for control centers in the petrochemical process industry. Some of the topics include guidelines for the optimized workstation design, control room layout, building layout, and lighting, acoustical and environmental design. Also takes into account the safety parameters in the control rooms and centers design. The conditions and parameters shown in this paper come from the standards and global advances on this topic on the most recent publications. And also the work was supplemented by field visits of our team to the control center operations in a petrochemical company, and technical literature search efforts. This guideline will be useful to increase the productivity and improve the working conditions at the control rooms.

Reliability-Based Electronics Shielding Design Tools

NASA Technical Reports Server (NTRS)

Wilson, J. W.; O'Neill, P. J.; Zang, T. A.; Pandolf, J. E.; Tripathi, R. K.; Koontz, Steven L.; Boeder, P.; Reddell, B.; Pankop, C.

2007-01-01

Shielding design on large human-rated systems allows minimization of radiation impact on electronic systems. Shielding design tools require adequate methods for evaluation of design layouts, guiding qualification testing, and adequate follow-up on final design evaluation.

Analysis on the Relationship Between Layout and Consumption of Face Cutters on Hard Rock Tunnel Boring Machines (TBMs)

NASA Astrophysics Data System (ADS)

Geng, Qi; Bruland, Amund; Macias, Francisco Javier

2018-01-01

The consumption of TBM disc cutters is influenced by the ground conditions (e.g. intact rock properties, rock mass properties, etc.), the TBM boring parameters (e.g. thrust, RPM, penetration, etc.) and the cutterhead design parameters (e.g. cutterhead shape, cutter layout). Previous researchers have done much work on the influence of the ground conditions and TBM boring parameters on cutter consumption; however, limited research has been found on the relationship between the cutterhead design and cutter consumption. The purpose of the present paper is to study the influence of layout on consumption for the TBM face cutters. Data collected from six tunnels (i.e. the Røssåga Headrace Tunnel in Norway, the Qinling Railway Tunnel in China, tubes 3 and 4 of the Guadarrama Railway Tunnel in Spain, the parallel tubes of the Vigo-Das Maceiras Tunnel in Spain) were used for analysis. The cutter consumption shape curve defined as the fitted function of the normalized cutter consumption versus the cutter position radius is found to be uniquely determined by the cutter layout and was used for analysis. The straightness and smoothness indexes are introduced to evaluate the quality of the shape curves. The analytical results suggest that the spacing of face cutters in the inner and outer parts of cutterhead should to be slightly larger and smaller, respectively, than the average spacing, and the difference of the position angles between the neighbouring cutters should be constant among the cutter positions. The 2-spiral layout pattern is found to be better than other layout patterns in view of cutter consumption and cutterhead force balance.

Habitable Mars Ascent Vehicle (MAV) Concept. [Mars Ascent Vehicle (MAV) Layout and Configuration: 6-Crew, Habitable, Nested Tank Concept

NASA Technical Reports Server (NTRS)

Dang, Victor; Rucker, Michelle

2013-01-01

NASA's ultimate goal is the human exploration of Mars. Among the many difficult aspects of a trip to Mars is the return mission that would transport the astronauts from the Martian surface back into Mars orbit. One possible conceptual design to accomplish this task is a two-stage Mars Ascent Vehicle (MAV). In order to assess this design, a general layout and configuration for the spacecraft must be developed. The objective of my internship was to model a conceptual MAV design to support NASA's latest human Mars mission architecture trade studies, technology prioritization decisions, and mass, cost, and schedule estimates.

Energy efficient LED layout optimization for near-uniform illumination

NASA Astrophysics Data System (ADS)

Ali, Ramy E.; Elgala, Hany

2016-09-01

In this paper, we consider the problem of designing energy efficient light emitting diodes (LEDs) layout while satisfying the illumination constraints. Towards this objective, we present a simple approach to the illumination design problem based on the concept of the virtual LED. We formulate a constrained optimization problem for minimizing the power consumption while maintaining a near-uniform illumination throughout the room. By solving the resulting constrained linear program, we obtain the number of required LEDs and the optimal output luminous intensities that achieve the desired illumination constraints.

Soviet Space Stations as Analogs, Second Edition

NASA Technical Reports Server (NTRS)

Bluth, B. J.; Helppie, Martha

1986-01-01

The available literature that discusses the various aspects of the Soviet Salyut 6 and Salyut 7 space staions are examined as related to human productivity. The methodology for this analog was a search of unclassified literature. Additional information was obtained in interviews with the cosmonauts and some Soviet space personnel. Topics include: general layout and design of the spacecraft system; cosmonauts role in maintenance and repair; general layout and design of the Mir complex; effects of the environment on personnel; information and computer systems; organization systems; personality systems; and physical conditin of the cosmonaut.

The Parable of the Boiled Safety Professional

NASA Technical Reports Server (NTRS)

Shivers, Charles H.

2011-01-01

Common and unique issues contribute to system failures. This paper touches on the concept of drift to failure as a cautionary message. Managers and leaders, design team members, fabricators and assemblers, analysis and assurance personnel, and others associated with operating and maintaining systems, need to pay attention to identify the manifestation of individual and collective behaviors that might indicate slips in rigor or focus or decisions that might eat away at safety margins as our system drifts to failure. Corrections to drift made during design and development phases may efficiently prevent or mitigate drift problems occurring in the operational phase.

49 CFR Appendix D to Part 213 - Minimally Compliant Analytical Track (MCAT) Simulations Used for Qualifying Vehicles To Operate...

Code of Federal Regulations, 2014 CFR

2014-10-01

... key responses observed during qualification testing. (b) MCAT layout. MCAT consists of nine segments, each designed to test a vehicle's performance in response to a specific type of track perturbation. The basic layout of MCAT is shown in figure 1 of this appendix, by type of track (curving or tangent), class...

49 CFR Appendix D to Part 213 - Minimally Compliant Analytical Track (MCAT) Simulations Used for Qualifying Vehicles To Operate...

Code of Federal Regulations, 2013 CFR

2013-10-01

... key responses observed during qualification testing. (b) MCAT layout. MCAT consists of nine segments, each designed to test a vehicle's performance in response to a specific type of track perturbation. The basic layout of MCAT is shown in figure 1 of this appendix, by type of track (curving or tangent), class...

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP.

PubMed

Deng, Li; Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency.

Layout-aware simulation of soft errors in sub-100 nm integrated circuits

NASA Astrophysics Data System (ADS)

Balbekov, A.; Gorbunov, M.; Bobkov, S.

2016-12-01

Single Event Transient (SET) caused by charged particle traveling through the sensitive volume of integral circuit (IC) may lead to different errors in digital circuits in some cases. In technologies below 180 nm, a single particle can affect multiple devices causing multiple SET. This fact adds the complexity to fault tolerant devices design, because the schematic design techniques become useless without their layout consideration. The most common layout mitigation technique is a spatial separation of sensitive nodes of hardened circuits. Spatial separation decreases the circuit performance and increases power consumption. Spacing should thus be reasonable and its scaling follows the device dimensions' scaling trend. This paper presents the development of the SET simulation approach comprised of SPICE simulation with "double exponent" current source as SET model. The technique uses layout in GDSII format to locate nearby devices that can be affected by a single particle and that can share the generated charge. The developed software tool automatizes multiple simulations and gathers the produced data to present it as the sensitivity map. The examples of conducted simulations of fault tolerant cells and their sensitivity maps are presented in this paper.

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP

PubMed Central

Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency. PMID:26448740

A Physics-Based Approach for Power Integrity in Multi-Layered PCBs

NASA Astrophysics Data System (ADS)

Zhao, Biyao

Developing a power distribution network (PDN) for ASICs and ICs to achieve the low-voltage ripple specifications for current digital designs is challenging with the high-speed and low-voltage ICs. Present methods are typically guided by best engineering practices for low impedance looking into the PDN from the IC. A pre-layout design methodology for power integrity in multi-layered PCB PDN geometry is proposed in the thesis. The PCB PDN geometry is segmented into four parts and every part is modelled using different methods based on the geometry details of the part. Physics-based circuit models are built for every part and the four parts are re-assembled into one model. The influence of geometry details is clearly revealed in this methodology. Based on the physics-based circuit mode, the procedures of using the pre-layout design methodology as a guideline during the PDN design is illustrated. Some common used geometries are used to build design space, and the design curves with the geometry details are provided to be a look up library for engineering use. The pre-layout methodology is based on the resonant cavity model of parallel planes for the cavity structures, and parallel-plane PEEC (PPP) for the irregular shaped plane inductance, and PEEC for the decoupling capacitor connection above the top most or bottom most power-return planes. PCB PDN is analyzed based on the input impedance looking into the PCB from the IC. The pre-layout design methodology can be used to obtain the best possible PCB PDN design. With the switching current profile, the target impedance can be selected to evaluate the PDN performance, and the frequency domain PDN input impedance can be used to obtain the voltage ripple in the time domain to give intuitive insight of the geometry impact on the voltage ripple.

Design of Reconnaissance Helicopter Electromagnetic and Magnetic Geophysical Surveys of the North Platte River and Lodgepole Creek, Nebraska

NASA Astrophysics Data System (ADS)

Smith, B. D.; Cannia, J. C.; Abraham, J. D.

2009-12-01

An innovative flight line layout using widely separated lines was used for frequency domain helicopter electromagnetic (HEM) surveys in 2008 and 2009 in the Panhandle of western Nebraska. The HEM survey design was developed as part of a joint hydrologic study by the North Platte Natural Resource District, South Platte Natural Resource District, UNL-Conservation and Survey Division, and U.S. Geological Survey to improve the understanding of relationships between surface water and groundwater systems critical to developing groundwater flow models used in water resources management programs. Use of HEM methods for hydrologic mapping had been demonstrated by HEM surveys conducted in 2007 of sites in the glaciated Platte River Basin in eastern Nebraska. These surveys covered township-scale areas with flight lines laid out in blocks where the lines were spaced about 270m apart. The HEM successfully mapped the complex 3D geometry of shallow sand and gravel aquifers through and within conductive till to a depth of about 40m in a total area of about 680 km2 (263 mi2). Current groundwater flow models in western Nebraska include the Cooperative Hydrologic Study (COHYST), run by a consortium of state agencies, which is tasked to develop scientifically supportable hydrologic databases, analyses, and models, and the North Platte River Valley Optimization Model (NPRVOM). The COHYST study area, about 75,000 km2 (29,000 mi2), includes the Platte River Basin from the Nebraska - Wyoming border to Lincoln. Considering the large area of the groundwater models, the USGS decided in collaboration with the NRD to use a more reconnaissance-style layout for the 2008 HEM survey which encompassed about 21,000 km2 (8,000 mi2). A reconnaissance-type HEM survey is made possible due to technical capabilities of applicable HEM systems and due to the level of hydrogeologic information available in the NRD. The particular capabilities of the HEM system are careful calibration, low drift, low noise, and leveling. The widely spaced lines do not provide as much opportunity for self-checking by line-to-line correlation as closely spaced lines. The final project design in 2008 consisted of flight lines paralleling the major drainages and lines perpendicular to the drainages spaced about 10 km (6 mi) apart. Layout of lines following the drainages is similar to the design of previous HEM surveys of levees. Although the general geologic features are known to be broad (sandstone channels and bedrock topography) from wells spaced about 2.5 km (1.5 mi), two “standard blocks” were flown with 270 m line spacing in critical areas to both better resolve of electrical signatures and to provide greater detail than the reconnaissance survey. The processed data from the two detailed survey blocks confirmed hypothesized electrical signatures of major hydrostratigraphic units in the area. Interpretation of data from the widely spaced lines, lines along the rivers, and the detail blocks fit well with the known hydrogeology.

Self-shielding flex-circuit drift tube, drift tube assembly and method of making

DOEpatents

Jones, David Alexander

2016-04-26

The present disclosure is directed to an ion mobility drift tube fabricated using flex-circuit technology in which every other drift electrode is on a different layer of the flex-circuit and each drift electrode partially overlaps the adjacent electrodes on the other layer. This results in a self-shielding effect where the drift electrodes themselves shield the interior of the drift tube from unwanted electro-magnetic noise. In addition, this drift tube can be manufactured with an integral flex-heater for temperature control. This design will significantly improve the noise immunity, size, weight, and power requirements of hand-held ion mobility systems such as those used for explosive detection.

Consumer’s Perception on Design and Layout of Consumer Medical Information Leaflets on Obesity and Lipid Lowering Drugs

PubMed Central

Mathew, Elizabeth M.; Rajiah, Kingston; Sharma, Krishana Kumar

2013-01-01

Background: Printed education materials are often used to augment healthcare professional’s verbal information to consumers so it serves as an important component of symptom management. They also enhance the teaching process and can be used by consumers as a home reference. Objective: This study was aimed to interpret consumers’ perception on Consumer Medical Information Leaflets (CMILs) on obesity and lipid lowering drugs, on design and layout using the standard method such as Baker Able Leaflet Design (BALD). Material and Methods: Convenience sampling was done. The study was conducted over a period of 3 years in community pharmacy settings in Tamil Nadu, India. The Consumer Medical Information Leaflets (CMILs) were randomly collected from different community pharmacies. Total of 19 CMILs which are commonly used by the consumers were collected and CMILs were assessed using BALD assessment tool Results: According to BALD assessment (46.28%) leaflets were rated as ‘above standard’ and (53.72) leaflets were rated as ‘standard or poor’ in layout and design since their scores were less than 25. This shows that this issue may be important from the patient’s perspective, which may discourage patient from actually reading the CMILs. Conclusion: In India, generally CMILs are continued to be prepared in English and with higher proportion of consumers with English illiteracy. CMILs, which are prepared without taking consideration of reading level of consumers and proper layout and design, may not achieve the intended purpose. This is an important aspect that any company has to reckon while preparing leaflets and at least in some major local languages in which CMILs have to be prepared. PMID:24551641

A fast process development flow by applying design technology co-optimization

NASA Astrophysics Data System (ADS)

Chen, Yi-Chieh; Yeh, Shin-Shing; Ou, Tsong-Hua; Lin, Hung-Yu; Mai, Yung-Ching; Lin, Lawrence; Lai, Jun-Cheng; Lai, Ya Chieh; Xu, Wei; Hurat, Philippe

2017-03-01

Beyond 40 nm technology node, the pattern weak points and hotspot types increase dramatically. The typical patterns for lithography verification suffers huge turn-around-time (TAT) to handle the design complexity. Therefore, in order to speed up process development and increase pattern variety, accurate design guideline and realistic design combinations are required. This paper presented a flow for creating a cell-based layout, a lite realistic design, to early identify problematic patterns which will negatively affect the yield. A new random layout generating method, Design Technology Co-Optimization Pattern Generator (DTCO-PG), is reported in this paper to create cell-based design. DTCO-PG also includes how to characterize the randomness and fuzziness, so that it is able to build up the machine learning scheme which model could be trained by previous results, and then it generates patterns never seen in a lite design. This methodology not only increases pattern diversity but also finds out potential hotspot preliminarily. This paper also demonstrates an integrated flow from DTCO pattern generation to layout modification. Optical Proximity Correction, OPC and lithographic simulation is then applied to DTCO-PG design database to detect hotspots and then hotspots or weak points can be automatically fixed through the procedure or handled manually. This flow benefits the process evolution to have a faster development cycle time, more complexity pattern design, higher probability to find out potential hotspots in early stage, and a more holistic yield ramping operation.

A Design Support Framework through Dynamic Deployment of Hypothesis and Verification in the Design Process

NASA Astrophysics Data System (ADS)

Nomaguch, Yutaka; Fujita, Kikuo

This paper proposes a design support framework, named DRIFT (Design Rationale Integration Framework of Three layers), which dynamically captures and manages hypothesis and verification in the design process. A core of DRIFT is a three-layered design process model of action, model operation and argumentation. This model integrates various design support tools and captures design operations performed on them. Action level captures the sequence of design operations. Model operation level captures the transition of design states, which records a design snapshot over design tools. Argumentation level captures the process of setting problems and alternatives. The linkage of three levels enables to automatically and efficiently capture and manage iterative hypothesis and verification processes through design operations over design tools. In DRIFT, such a linkage is extracted through the templates of design operations, which are extracted from the patterns embeded in design tools such as Design-For-X (DFX) approaches, and design tools are integrated through ontology-based representation of design concepts. An argumentation model, gIBIS (graphical Issue-Based Information System), is used for representing dependencies among problems and alternatives. A mechanism of TMS (Truth Maintenance System) is used for managing multiple hypothetical design stages. This paper also demonstrates a prototype implementation of DRIFT and its application to a simple design problem. Further, it is concluded with discussion of some future issues.

Comparative study on different types of segmented micro deformable mirrors

NASA Astrophysics Data System (ADS)

Qiao, Dayong; Yuan, Weizheng; Li, Kaicheng; Li, Xiaoying; Rao, Fubo

2006-02-01

In an adaptive-optical (AO) system, the wavefront of optical beam can be corrected with deformable mirror (DM). Based on MicroElectroMechanical System (MEMS) technology, segmented micro deformable mirrors can be built with denser actuator spacing than continuous face-sheet designs and have been widely researched. But the influence of the segment structure has not been thoroughly discussed until now. In this paper, the design, performance and fabrication of several micromachined, segmented deformable mirror for AO were investigated. The wavefront distorted by atmospheric turbulence was simulated in the frame of Kolmogorov turbulence model. Position function was used to describe the surfaces of the micro deformable mirrors in working state. The performances of deformable mirrors featuring square, brick, hexagonal and ring segment structures were evaluated in criteria of phase fitting error, the Strehl ratio after wavefront correction and the design considerations. Then the micro fabrication process and mask layout were designed and the fabrication of micro deformable mirrors was implemented. The results show that the micro deformable mirror with ring segments performs the best, but it is very difficult in terms of layout design. The micro deformable mirrors with square and brick segments are easy to design, but their performances are not good. The micro deformable mirror with hexagonal segments has not only good performance in terms of phase fitting error, the Strehl ratio and actuation voltage, but also no overwhelming difficulty in layout design.

Spacecraft Habitable Volume: Results of an Interdisciplinary Workshop

NASA Technical Reports Server (NTRS)

Fitts, David J.; Connolly, Janis; Howard, Robert

2011-01-01

NASA's Human Exploration Framework Team posed the question: "Is 80 cubic meters per person of habitable volume acceptable for a proposed Deep Space Habitat?" The goal of the workshop was to address the "net habitable volume" necessary for long-duration human spaceflight missions and identify design and psychological issues and mitigations. The objectives were: (1) Identify psychological factors -- i.e., "stressors" -- that impact volume and layout specifications for long duration missions (2) Identify mitigation strategies for stressors, especially those that can be written as volume design specifications (3) Identify a forward research roadmap -- i.e., what future work is needed to define and validate objective design metrics? (4) Provide advisories on the human factors consequences of poor net habitable volume allocation and layout design.

New PDC bit design reduces vibrational problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mensa-Wilmot, G.; Alexander, W.L.

1995-05-22

A new polycrystalline diamond compact (PDC) bit design combines cutter layout, load balancing, unsymmetrical blades and gauge pads, and spiraled blades to reduce problematic vibrations without limiting drilling efficiency. Stabilization improves drilling efficiency and also improves dull characteristics for PDC bits. Some PDC bit designs mitigate one vibrational mode (such as bit whirl) through drilling parameter manipulation yet cause or excite another vibrational mode (such as slip-stick). An alternative vibration-reducing concept which places no limitations on the operational environment of a PDC bit has been developed to ensure optimization of the bit`s available mechanical energy. The paper discusses bit stabilization,more » vibration reduction, vibration prevention, cutter arrangement, load balancing, blade layout, spiraled blades, and bit design.« less

Route visualization using detail lenses.

PubMed

Karnick, Pushpak; Cline, David; Jeschke, Stefan; Razdan, Anshuman; Wonka, Peter

2010-01-01

We present a method designed to address some limitations of typical route map displays of driving directions. The main goal of our system is to generate a printable version of a route map that shows the overview and detail views of the route within a single, consistent visual frame. Our proposed visualization provides a more intuitive spatial context than a simple list of turns. We present a novel multifocus technique to achieve this goal, where the foci are defined by points of interest (POI) along the route. A detail lens that encapsulates the POI at a finer geospatial scale is created for each focus. The lenses are laid out on the map to avoid occlusion with the route and each other, and to optimally utilize the free space around the route. We define a set of layout metrics to evaluate the quality of a lens layout for a given route map visualization. We compare standard lens layout methods to our proposed method and demonstrate the effectiveness of our method in generating aesthetically pleasing layouts. Finally, we perform a user study to evaluate the effectiveness of our layout choices.

Global Sentry: NASA/USRA high altitude reconnaissance aircraft design, volume 2

NASA Technical Reports Server (NTRS)

Alexandru, Mona-Lisa; Martinez, Frank; Tsou, Jim; Do, Henry; Peters, Ashish; Chatsworth, Tom; Yu, YE; Dhillon, Jaskiran

1990-01-01

The Global Sentry is a high altitude reconnaissance aircraft design for the NASA/USRA design project. The Global Sentry uses proven technologies, light-weight composites, and meets the R.F.P. requirements. The mission requirements for the Global Sentry are described. The configuration option is discussed and a description of the final design is given. Preliminary sizing analyses and the mass properties of the design are presented. The aerodynamic features of the Global Sentry are described along with the stability and control characteristics designed into the flight control system. The performance characteristics are discussed as is the propulsion installation and system layout. The Global Sentry structural design is examined, including a wing structural analysis. The cockpit, controls and display layouts are covered. Manufacturing is covered and the life cost estimation. Reliability is discussed. Conclusions about the current Global Sentry design are presented, along with suggested areas for future engineering work.

What Would a Graph Look Like in this Layout? A Machine Learning Approach to Large Graph Visualization.

PubMed

Kwon, Oh-Hyun; Crnovrsanin, Tarik; Ma, Kwan-Liu

2018-01-01

Using different methods for laying out a graph can lead to very different visual appearances, with which the viewer perceives different information. Selecting a "good" layout method is thus important for visualizing a graph. The selection can be highly subjective and dependent on the given task. A common approach to selecting a good layout is to use aesthetic criteria and visual inspection. However, fully calculating various layouts and their associated aesthetic metrics is computationally expensive. In this paper, we present a machine learning approach to large graph visualization based on computing the topological similarity of graphs using graph kernels. For a given graph, our approach can show what the graph would look like in different layouts and estimate their corresponding aesthetic metrics. An important contribution of our work is the development of a new framework to design graph kernels. Our experimental study shows that our estimation calculation is considerably faster than computing the actual layouts and their aesthetic metrics. Also, our graph kernels outperform the state-of-the-art ones in both time and accuracy. In addition, we conducted a user study to demonstrate that the topological similarity computed with our graph kernel matches perceptual similarity assessed by human users.

Production facility layout by comparing moment displacement using BLOCPLAN and ALDEP Algorithms

NASA Astrophysics Data System (ADS)

Tambunan, M.; Ginting, E.; Sari, R. M.

2018-02-01

Production floor layout settings include the organizing of machinery, materials, and all the equipments used in the production process in the available area. PT. XYZ is a company that manufactures rubber and rubber compounds for retreading tire threaded with hot and cold cooking system. In the production of PT. XYZ is divided into three interrelated parts, namely Masterbatch Department, Department Compound, and Procured Thread Line Department. PT. XYZ has a production process with material flow is irregular and the arrangement of machine is complicated and need to be redesigned. The purpose of this study is comparing movement displacement using BLOCPLAN and ALDEP algorithm in order to redesign existing layout. Redesigning the layout of the production floor is done by applying algorithms of BLOCPLAN and ALDEP. The algorithm used to find the best layout design by comparing the moment displacement and the flow pattern. Moment displacement on the floor layout of the company’s production currently amounts to 2,090,578.5 meters per year and material flow pattern is irregular. Based on the calculation, the moment displacement for the BLOCPLAN is 1,551,344.82 meter per year and ALDEP is 1,600,179 meter per year. Flow Material resulted is in the form of straight the line.

A Glimpse in the Third Dimension for Electrical Resistivity Profiles

NASA Astrophysics Data System (ADS)

Robbins, A. R.; Plattner, A.

2017-12-01

We present an electrode layout strategy designed to enhance the popular two-dimensional electrical resistivity profile. Offsetting electrodes from the traditional linear layout and using 3-D inversion software allows for mapping the three-dimensional electrical resistivity close to the profile plane. We established a series of synthetic tests using simulated data generated from chosen resistivity distributions with a three-dimensional target feature. All inversions and simulations were conducted using freely-available ERT software, BERT and E4D. Synthetic results demonstrate the effectiveness of the offset electrode approach, whereas the linear layout failed to resolve the three-dimensional character of our subsurface feature. A field survey using trench backfill as a known resistivity contrast confirmed our synthetic tests. As we show, 3-D inversions of linear layouts for starting models without previously known structure are futile ventures because they generate symmetric resistivity solutions with respect to the profile plane. This is a consequence of the layout's inherent symmetrical sensitivity patterns. An offset electrode layout is not subject to the same limitation, as the collective measurements do not share a common sensitivity symmetry. For practitioners, this approach presents a low-cost improvement of a traditional geophysical method which is simple to use yet may provide critical information about the three dimensional structure of the subsurface close to the profile.

Associations of street layout with walking and sedentary behaviors in an urban and a rural area of Japan.

PubMed

Koohsari, Mohammad Javad; Sugiyama, Takemi; Shibata, Ai; Ishii, Kaori; Liao, Yung; Hanibuchi, Tomoya; Owen, Neville; Oka, Koichiro

2017-05-01

We examined whether street layout -a key urban design element- is associated with walking and sedentary behaviors in the context of a non-Western country; and, whether such associations differ between an urban and a rural area. In 2011, 1076 middle-to-older aged adults living in an urban and a rural area of Japan reported their walking and sedentary (sitting) behaviors. Two objective measures of street layout (intersection density and street integration) were calculated. Participants exposed to more-connected street layouts were more likely to walk for commuting and for errands, to meet physical activity recommendations through walking for commuting, and less likely to drive. These relationships differed between the urban and the rural area. This shows that previous findings from Western countries on associations of street connectivity with travel behaviors may also be applicable to Japan. Copyright © 2017 Elsevier Ltd. All rights reserved.

OSLay: optimal syntenic layout of unfinished assemblies.

PubMed

Richter, Daniel C; Schuster, Stephan C; Huson, Daniel H

2007-07-01

The whole genome shotgun approach to genome sequencing results in a collection of contigs that must be ordered and oriented to facilitate efficient gap closure. We present a new tool OSLay that uses synteny between matching sequences in a target assembly and a reference assembly to layout the contigs (or scaffolds) in the target assembly. The underlying algorithm is based on maximum weight matching. The tool provides an interactive visualization of the computed layout and the result can be imported into the assembly editing tool Consed to support the design of primer pairs for gap closure. To enhance efficiency in the gap closure phase of a genome project it is crucial to know which contigs are adjacent in the target genome. Related genome sequences can be used to layout contigs in an assembly. OSLay is freely available from: http://www-ab.informatik.unituebingen.de/software/oslay.

Model-based strategy for cell culture seed train layout verified at lab scale.

PubMed

Kern, Simon; Platas-Barradas, Oscar; Pörtner, Ralf; Frahm, Björn

2016-08-01

Cell culture seed trains-the generation of a sufficient viable cell number for the inoculation of the production scale bioreactor, starting from incubator scale-are time- and cost-intensive. Accordingly, a seed train offers potential for optimization regarding its layout and the corresponding proceedings. A tool has been developed to determine the optimal points in time for cell passaging from one scale into the next and it has been applied to two different cell lines at lab scale, AGE1.HN AAT and CHO-K1. For evaluation, experimental seed train realization has been evaluated in comparison to its layout. In case of the AGE1.HN AAT cell line, the results have also been compared to the formerly manually designed seed train. The tool provides the same seed train layout based on the data of only two batches.

[Influence of the space layout of a surgical department on use efficiency].

PubMed

Weiss, G; von Baer, R; Riedl, S

2002-02-01

There is a growing gap between the rapidly increasing diagnostic and therapeutic opportunities and the patient demands on one side and the continuously declining hospital budgets on the other side. This gap forces hospitals to search for rationalization potentials and ways to increase their efficiency. It is well known that the operating theatre unit is one of the most important internal cost factors. Many reorganization projects therefore focus on operating theatres. In Germany, several alternative operating room layouts have been developed in order to reduce running und building costs and to reach a high degree of flexibility in their everyday use by means of an improved design. This article analyses and compares the classic operating room and four alternative layouts intended to make them suitable for reaching the promised objectives and, especially, achieving an economically run business management. Furthermore, preferred layouts for certain types of operations are recommended.

Production layout improvement in emergency services: a participatory approach.

PubMed

Zanatta, Mateus; Amaral, Fernando Gonçalves

2012-01-01

Volunteer fire department is a service that responds emergency situations in places where there are no military emergency services. These services need to respond quickly, because time is often responsible for the operation success besides work environment and setup time interfere with the prompt response to these calls and care efficiency. The layout design is one factor that interferes with the quick setup. In this case, the spaces arrangement can result in excessive or unnecessary movements; also the equipment provision may hinder the selection and collection of these or even create movement barriers for the workers. This work created a new layout for the emergency assistance service, considering the human factors related to work through the task analysis and workers participation on the alternatives of improvement. The results showed an alternate layout with corridors and minimization of unusable sites, allowing greater flexibility and new possibilities of requirements.

Unequal-area, fixed-shape facility layout problems using the firefly algorithm

NASA Astrophysics Data System (ADS)

Ingole, Supriya; Singh, Dinesh

2017-07-01

In manufacturing industries, the facility layout design is a very important task, as it is concerned with the overall manufacturing cost and profit of the industry. The facility layout problem (FLP) is solved by arranging the departments or facilities of known dimensions on the available floor space. The objective of this article is to implement the firefly algorithm (FA) for solving unequal-area, fixed-shape FLPs and optimizing the costs of total material handling and transportation between the facilities. The FA is a nature-inspired algorithm and can be used for combinatorial optimization problems. Benchmark problems from the previous literature are solved using the FA. To check its effectiveness, it is implemented to solve large-sized FLPs. Computational results obtained using the FA show that the algorithm is less time consuming and the total layout costs for FLPs are better than the best results achieved so far.

Estimation of design space for an extrusion-spheronization process using response surface methodology and artificial neural network modelling.

PubMed

Sovány, Tamás; Tislér, Zsófia; Kristó, Katalin; Kelemen, András; Regdon, Géza

2016-09-01

The application of the Quality by Design principles is one of the key issues of the recent pharmaceutical developments. In the past decade a lot of knowledge was collected about the practical realization of the concept, but there are still a lot of unanswered questions. The key requirement of the concept is the mathematical description of the effect of the critical factors and their interactions on the critical quality attributes (CQAs) of the product. The process design space (PDS) is usually determined by the use of design of experiment (DoE) based response surface methodologies (RSM), but inaccuracies in the applied polynomial models often resulted in the over/underestimation of the real trends and changes making the calculations uncertain, especially in the edge regions of the PDS. The completion of RSM with artificial neural network (ANN) based models is therefore a commonly used method to reduce the uncertainties. Nevertheless, since the different researches are focusing on the use of a given DoE, there is lack of comparative studies on different experimental layouts. Therefore, the aim of present study was to investigate the effect of the different DoE layouts (2 level full factorial, Central Composite, Box-Behnken, 3 level fractional and 3 level full factorial design) on the model predictability and to compare model sensitivities according to the organization of the experimental data set. It was revealed that the size of the design space could differ more than 40% calculated with different polynomial models, which was associated with a considerable shift in its position when higher level layouts were applied. The shift was more considerable when the calculation was based on RSM. The model predictability was also better with ANN based models. Nevertheless, both modelling methods exhibit considerable sensitivity to the organization of the experimental data set, and the use of design layouts is recommended, where the extreme values factors are more represented. Copyright © 2016 Elsevier B.V. All rights reserved.

A quantum physical design flow using ILP and graph drawing

NASA Astrophysics Data System (ADS)

Yazdani, Maryam; Saheb Zamani, Morteza; Sedighi, Mehdi

2013-10-01

Implementing large-scale quantum circuits is one of the challenges of quantum computing. One of the central challenges of accurately modeling the architecture of these circuits is to schedule a quantum application and generate the layout while taking into account the cost of communications and classical resources as well as the maximum exploitable parallelism. In this paper, we present and evaluate a design flow for arbitrary quantum circuits in ion trap technology. Our design flow consists of two parts. First, a scheduler takes a description of a circuit and finds the best order for the execution of its quantum gates using integer linear programming regarding the classical resources (qubits) and instruction dependencies. Then a layout generator receives the schedule produced by the scheduler and generates a layout for this circuit using a graph-drawing algorithm. Our experimental results show that the proposed flow decreases the average latency of quantum circuits by about 11 % for a set of attempted benchmarks and by about 9 % for another set of benchmarks compared with the best in literature.

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2010 CFR

2010-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2014 CFR

2014-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2011 CFR

2011-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2013 CFR

2013-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2012 CFR

2012-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

Navigational Structure on the World Wide Web: Usability Concerns, User Preferences, and "Browsing Behavior."

ERIC Educational Resources Information Center

Frick, Theodore; Monson, John A.; Xaver, Richard F.; Kilic, Gulsen; Conley, Aaron T.; Wamey, Beatrice

There are several approaches a World Wide Web site designer considers in developing a menu structure. One consideration is the content of the menus (what choices are available to the user). Another consideration is the physical layout of the menu structure. The physical layout of a menu may be described as being one of at least three different…

An efficient way of layout processing based on calibre DRC and pattern matching for defects inspection application

NASA Astrophysics Data System (ADS)

Li, Helen; Lee, Robben; Lee, Tyzy; Xue, Teddy; Liu, Hermes; Wu, Hall; Wan, Qijian; Du, Chunshan; Hu, Xinyi; Liu, Zhengfang

2018-03-01

As technology advances, escalating layout design complexity and chip size make defect inspection becomes more challenging than ever before. The YE (Yield Enhancement) engineers are seeking for an efficient strategy to ensure accuracy without suffering running time. A smart way is to set different resolutions for different pattern structures, for examples, logic pattern areas have a higher scan resolution while the dummy areas have a lower resolution, SRAM area may have another different resolution. This can significantly reduce the scan processing time meanwhile the accuracy does not suffer. Due to the limitation of the inspection equipment, the layout must be processed in order to output the Care Area marker in line with the requirement of the equipment, for instance, the marker shapes must be rectangle and the number of the rectangle shapes should be as small as possible. The challenge is how to select the different Care Areas by pattern structures, merge the areas efficiently and then partition them into pieces of rectangle shapes. This paper presents a solution based on Calibre DRC and Pattern Matching. Calibre equation-based DRC is a powerful layout processing engine and Calibre Pattern Matching's automated visual capture capability enables designers to define these geometries as layout patterns and store them in libraries which can be re-used in multiple design layouts. Pattern Matching simplifies the description of very complex relationships between pattern shapes efficiently and accurately. Pattern matching's true power is on display when it is integrated with normal DRC deck. In this application of defects inspection, we first run Calibre DRC to get rule based Care Area then use Calibre Pattern Matching's automated pattern capture capability to capture Care Area shapes which need a higher scan resolution with a tune able pattern halo. In the pattern matching step, when the patterns are matched, a bounding box marker will be output to identify the high resolution area. The equation-based DRC and Pattern Matching effectively work together for different scan phases.

Artwork Interactive Design System (AIDS) program description

NASA Technical Reports Server (NTRS)

Johnson, B. T.; Taylor, J. F.

1976-01-01

An artwork interactive design system is described which provides the microelectronic circuit designer/engineer a tool to perform circuit design, automatic layout modification, standard cell design, and artwork verification at a graphics computer terminal using a graphics tablet at the designer/computer interface.

NetList(+): A simple interface language for chip design

NASA Astrophysics Data System (ADS)

Wuu, Tzyh-Yung

1991-04-01

NetList (+) is a design specification language developed at MOSIS for rapid turn-around cell-based ASIC prototyping. By using NetList (+), a uniform representation is achieved for the specification, simulation, and physical description of a design. The goal is to establish an interfacing methodology between design specification and independent computer aided design tools. Designers need only to specify a system by writing a corresponding netlist. This netlist is used for both functional simulation and timing simulation. The same netlist is also used to derive the low level physical tools to generate layout. Another goal of using NetList (+) is to generate parts of a design by running it through different kinds of placement and routing (P and R) tools. For example some parts of a design will be generated by standard cell P and R tools. Other parts may be generated by a layout tiler; i.e., datapath compiler, RAM/ROM generator, or PLA generator. Finally all different parts of a design can be integrated by general block P and R tools as a single chip. The NetList (+) language can actually act as an interface among tools. Section 2 shows a flowchart to illustrate the NetList (+) system and its relation with other related design tools. Section 3 shows how to write a NetList (+) description from the block diagram of a circuit. In section 4 discusses how to prepare a cell library or several cell libraries for a design system. Section 5 gives a few designs by NetList (+) and shows their simulation and layout results.

Optical layout and mechanical structure of polarimeter-interferometer system for Experimental Advanced Superconducting Tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zou, Z. Y.; Liu, H. Q., E-mail: hqliu@ipp.ac.cn; Jie, Y. X.

A Far-InfaRed (FIR) three-wave POlarimeter-INTerferometer (POINT) system for measurement current density profile and electron density profile is under development for the EAST tokamak. The FIR beams are transmitted from the laser room to the optical tower adjacent to EAST via ∼20 m overmoded dielectric waveguide and then divided into 5 horizontal chords. The optical arrangement was designed using ZEMAX, which provides information on the beam spot size and energy distribution throughout the optical system. ZEMAX calculations used to optimize the optical layout design are combined with the mechanical design from CATIA, providing a 3D visualization of the entire POINT system.

Optical layout and mechanical structure of polarimeter-interferometer system for Experimental Advanced Superconducting Tokamak.

PubMed

Zou, Z Y; Liu, H Q; Jie, Y X; Ding, W X; Brower, D L; Wang, Z X; Shen, J S; An, Z H; Yang, Y; Zeng, L; Wei, X C; Li, G S; Zhu, X; Lan, T

2014-11-01

A Far-InfaRed (FIR) three-wave POlarimeter-INTerferometer (POINT) system for measurement current density profile and electron density profile is under development for the EAST tokamak. The FIR beams are transmitted from the laser room to the optical tower adjacent to EAST via ∼20 m overmoded dielectric waveguide and then divided into 5 horizontal chords. The optical arrangement was designed using ZEMAX, which provides information on the beam spot size and energy distribution throughout the optical system. ZEMAX calculations used to optimize the optical layout design are combined with the mechanical design from CATIA, providing a 3D visualization of the entire POINT system.

Adiabatic quantum-flux-parametron cell library adopting minimalist design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takeuchi, Naoki, E-mail: takeuchi-naoki-kx@ynu.jp; Yamanashi, Yuki; Yoshikawa, Nobuyuki

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells inmore » the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.« less

Adiabatic quantum-flux-parametron cell library adopting minimalist design

NASA Astrophysics Data System (ADS)

Takeuchi, Naoki; Yamanashi, Yuki; Yoshikawa, Nobuyuki

2015-05-01

We herein build an adiabatic quantum-flux-parametron (AQFP) cell library adopting minimalist design and a symmetric layout. In the proposed minimalist design, every logic cell is designed by arraying four types of building block cells: buffer, NOT, constant, and branch cells. Therefore, minimalist design enables us to effectively build and customize an AQFP cell library. The symmetric layout reduces unwanted parasitic magnetic coupling and ensures a large mutual inductance in an output transformer, which enables very long wiring between logic cells. We design and fabricate several logic circuits using the minimal AQFP cell library so as to test logic cells in the library. Moreover, we experimentally investigate the maximum wiring length between logic cells. Finally, we present an experimental demonstration of an 8-bit carry look-ahead adder designed using the minimal AQFP cell library and demonstrate that the proposed cell library is sufficiently robust to realize large-scale digital circuits.

Built environmental factors and adults' travel behaviors: Role of street layout and local destinations.

PubMed

Koohsari, Mohammad Javad; Owen, Neville; Cole, Rachel; Mavoa, Suzanne; Oka, Koichiro; Hanibuchi, Tomoya; Sugiyama, Takemi

2017-03-01

Street layout is consistently associated with adults' travel behaviors, however factors influencing this association are unclear. We examined associations of street layout with travel behaviors: walking for transport (WT) and car use; and, the extent to which these relationships may be accounted for by availability of local destinations. A 24-h travel diary was completed in 2009 by 16,345 adult participants of the South-East Queensland Household Travel Survey, Australia. Three travel-behavior outcomes were derived: any home-based WT; over 30min of home-based WT; and, over 60min of car use. For street layout, a space syntax measure of street integration was calculated for each Statistical Area 1 (SA1, the smallest geographic unit in Australia). An objective measure of availability of destinations - Walk Score - was also derived for each SA1. Logistic regression examined associations of street layout with travel behaviors. Mediation analyses examined to what extent availability of destinations explained the associations. Street integration was significantly associated with travel behaviors. Each one-decile increment in street integration was associated with an 18% (95%CI: 1.15, 1.21) higher odds of any home-based WT; a 10% (95%CI: 1.06, 1.15) higher odds of over 30min of home-based WT; and a 5% (95%CI: 0.94, 0.96) lower odds of using a car over 60min. Local destinations partially mediated the effects of street layout on travel behaviors. Well-connected street layout contributes to active travel partially through availability of more local destinations. Urban design strategies need to address street layout and destinations to promote active travel among residents. Copyright © 2016 Elsevier Inc. All rights reserved.

The effect of hospital unit layout on nurse walking behavior.

PubMed

Yi, Lu; Seo, Hyun-Bo

2012-01-01

To confirm a new method for the research question, "How do different hospital unit layouts affect nurses' walking behavior and distance?" Concern is renewed regarding nurses' long walking distances because of the trend toward larger patient rooms with family areas inside, resulting in a larger overall unit size. Studies have found unit design characteristics that support nurses' efficient walking, but few have done it in units designed for patient- and family-centered care. To examine the effect of unit design on nurses' walking behavior, the authors propose a new method of observing a specific task. The authors observed nurses during the task of medication administration. Contrary to their hypotheses, results showed: (1) Experienced nurses had more unnecessary stops and longer walking distances than new nurses because of interactions; and (2) nurses in the smaller wing of the unit walked more than those in the larger wing of the same unit. The authors posit that the closeness between the nurses' path to the medication supply room and the central nurses' station affected the frequency of interactions and prompted a deviation from the shortest and most efficient path during medication administration. Observing a specific task to identify the effect of unit layout was effective, determining that overall unit shape or unit layout type might not be a good predictor of nurses' walking behavior; instead the characteristics of the path that connects functional spaces such as patient room and medication area might better predict nurses' walking behavior.

SimArray: a user-friendly and user-configurable microarray design tool

PubMed Central

Auburn, Richard P; Russell, Roslin R; Fischer, Bettina; Meadows, Lisa A; Sevillano Matilla, Santiago; Russell, Steven

2006-01-01

Background Microarrays were first developed to assess gene expression but are now also used to map protein-binding sites and to assess allelic variation between individuals. Regardless of the intended application, efficient production and appropriate array design are key determinants of experimental success. Inefficient production can make larger-scale studies prohibitively expensive, whereas poor array design makes normalisation and data analysis problematic. Results We have developed a user-friendly tool, SimArray, which generates a randomised spot layout, computes a maximum meta-grid area, and estimates the print time, in response to user-specified design decisions. Selected parameters include: the number of probes to be printed; the microtitre plate format; the printing pin configuration, and the achievable spot density. SimArray is compatible with all current robotic spotters that employ 96-, 384- or 1536-well microtitre plates, and can be configured to reflect most production environments. Print time and maximum meta-grid area estimates facilitate evaluation of each array design for its suitability. Randomisation of the spot layout facilitates correction of systematic biases by normalisation. Conclusion SimArray is intended to help both established researchers and those new to the microarray field to develop microarray designs with randomised spot layouts that are compatible with their specific production environment. SimArray is an open-source program and is available from . PMID:16509966

Alternating phase-shifted mask for logic gate levels, design, and mask manufacturing

NASA Astrophysics Data System (ADS)

Liebmann, Lars W.; Graur, Ioana C.; Leipold, William C.; Oberschmidt, James M.; O'Grady, David S.; Regaill, Denis

1999-07-01

While the benefits of alternating phase shifted masks in improving lithographic process windows at increased resolution are well known throughout the lithography community, broad implementation of this potentially powerful technique has been slow due to the inherent complexity of the layout design and mask manufacturing process. This paper will review a project undertaken at IBM's Semiconductor Research and Development Center and Mask Manufacturing and Development facility to understand the technical and logistical issues associated with the application of alternating phase shifted mask technology to the gate level of a full microprocessor chip. The work presented here depicts an important milestone toward integration of alternating phase shifted masks into the manufacturing process by demonstrating an automated design solution and yielding a functional alternating phase shifted mask. The design conversion of the microprocessor gate level to a conjugate twin shifter alternating phase shift layout was accomplished with IBM's internal design system that automatically scaled the design, added required phase regions, and resolved phase conflicts. The subsequent fabrication of a nearly defect free phase shifted mask, as verified by SEM based die to die inspection, highlights the maturity of the alternating phase shifted mask manufacturing process in IBM's internal mask facility. Well defined and recognized challenges in mask inspection and repair remain and the layout of alternating phase shifted masks present a design and data preparation overhead, but the data presented here demonstrate the feasibility of designing and building manufacturing quality alternating phase shifted masks for the gate level of a microprocessor.

A New Capability for Nuclear Thermal Propulsion Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amiri, Benjamin W.; Nuclear and Radiological Engineering Department, University of Florida, Gainesville, FL 32611; Kapernick, Richard J.

2007-01-30

This paper describes a new capability for Nuclear Thermal Propulsion (NTP) design that has been developed, and presents the results of some analyses performed with this design tool. The purpose of the tool is to design to specified mission and material limits, while maximizing system thrust to weight. The head end of the design tool utilizes the ROCket Engine Transient Simulation (ROCETS) code to generate a system design and system design requirements as inputs to the core analysis. ROCETS is a modular system level code which has been used extensively in the liquid rocket engine industry for many years. Themore » core design tool performs high-fidelity reactor core nuclear and thermal-hydraulic design analysis. At the heart of this process are two codes TMSS-NTP and NTPgen, which together greatly automate the analysis, providing the capability to rapidly produce designs that meet all specified requirements while minimizing mass. A PERL based command script, called CORE DESIGNER controls the execution of these two codes, and checks for convergence throughout the process. TMSS-NTP is executed first, to produce a suite of core designs that meet the specified reactor core mechanical, thermal-hydraulic and structural requirements. The suite of designs consists of a set of core layouts and, for each core layout specific designs that span a range of core fuel volumes. NTPgen generates MCNPX models for each of the core designs from TMSS-NTP. Iterative analyses are performed in NTPgen until a reactor design (fuel volume) is identified for each core layout that meets cold and hot operation reactivity requirements and that is zoned to meet a radial core power distribution requirement.« less

Designing high-performance cost-efficient embedded SRAM in deep-submicron era

NASA Astrophysics Data System (ADS)

Kobozeva, Olga; Venkatraman, Ramnath; Castagnetti, Ruggero; Duan, Franklin; Kamath, Arvind; Ramesh, Shiva

2004-05-01

We have previously presented the smallest and fastest 6 Transistor (6T)-Static Random Access Memories (SRAM) bitcells for System-on-Chip (SoC) high-density (HD) memories in 0.18 μm and 0.13 μm technologies. Our 1.87 μm2 6TSRAM bitcell with cell current of 47 μA and industry lowest soft error rate (0.35 FIT/Kbit) is used to assemble memory blocks embedded into SoC designs in 0.13 μm process technology. Excellent performance is achieved at a low overall cost, as our bitcells are based on standard CMOS process and demonstrate high yields in manufacturing. This paper discusses our methodology of embedded SRAM bitcell design. The key aspects of our approach are: 1) judicious selection of tightest achievable yet manufacturable design rules to build the cell; 2) compatibility with standard Optical Proximity Correction (OPC) flow; 3) use of parametric testing and yield analysis to achieve excellent design robustness and manufacturability. A thorough understanding of process limitations, particularly those related to photolithography was critical to the successful design and manufacturing of our aggressive, yet robust SRAM bitcells. The patterning of critical layers, such as diffusion, poly gate, contact and metal 1 has profound implications on functionality, electrical performance and manufacturability of memories. We have conducted the development of SRAM bitcells using two approaches for OPC: a) "manual" OPC, wherein the bitcell layout of each of the critical layers is achieved using iterative improvement of layout & aerial image simulation and b) automated OPC-compatible design, wherein the drawn bitcell layout becomes a subject of a full chip OPC. While manual-OPC remains a popular option, automated OPC-compatible bitcell design is very attractive, as it does not require additional development costs to achieve fab-to-fab portability. In both cases we have obtained good results with respect to patterning of the critical layers, electrical performance of the bitcell and memory yields. A critical part of our memory technology development effort is the design of memory-specific test structures that are used for: a) verifying electrical characteristics of SRAM transistors and b) confirming the robustness of the design rules used within the SRAM cell. In addition to electrical test structures, we have a fully functional SRAM test chip called RAMPCM that is composed of sub-blocks each designated to evaluate the robustness of a specific critical design rule used within the bitcells. The results from the electrical testing and RAMPCM yield analysis are used to identify opportunities for improvements in the layout design. The paper will also suggest some techniques that can result in more design friendly OPC solutions. Our work indicates that future IC designs can benefit from an automated OPC tool that can intelligently handle layout modifications according to design priorities.

7 CFR 634.5 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... participant water quality plans; design, layout and application of BMP's; and investigations associated with..., designing, installing, and maintaining BMP's. (aa) State. Any of the several States of the United States...

7 CFR 634.5 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... participant water quality plans; design, layout and application of BMP's; and investigations associated with..., designing, installing, and maintaining BMP's. (aa) State. Any of the several States of the United States...

7 CFR 634.5 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... participant water quality plans; design, layout and application of BMP's; and investigations associated with..., designing, installing, and maintaining BMP's. (aa) State. Any of the several States of the United States...

15 CFR 744.21 - Restrictions on certain military end-uses in the People's Republic of China (PRC).

Code of Federal Regulations, 2013 CFR

2013-01-01

... production, such as: design, design research, design analyses, design concepts, assembly and testing of prototypes, pilot production schemes, design data, process of transforming design data into a product, configuration design, integration design, layouts; and “production” means all production stages, such as...

15 CFR 744.21 - Restrictions on certain military end-uses in the People's Republic of China (PRC).

Code of Federal Regulations, 2012 CFR

2012-01-01

... production, such as: design, design research, design analyses, design concepts, assembly and testing of prototypes, pilot production schemes, design data, process of transforming design data into a product, configuration design, integration design, layouts; and “production” means all production stages, such as...

Layout of personnel accommodations for the SOFIA

NASA Astrophysics Data System (ADS)

Daughters, David M.; Bruich, J. G.; Arceneaux, Gregory P.; Zirretta, Jason; Caton, William B.

2000-06-01

The NASA Stratospheric Observatory for Infrared Astronomy (SOFIA) Observatory is based upon a refurbished and heavily modified Boeing 747 SP aircraft. The Observatory, which provides accommodations for the Deutsches Zentrum Fur Luftund Raumfahrt 2.5 m telescope, science investigator teams, scientific instruments, mission crew and support systems. The US contractor team has removed most of the aircraft original furnishings and designed a new Layout of Personnel Accommodations (LOPA) tailored to SOFIA's needs.

N-Channel field-effect transistors with floating gates for extracellular recordings.

PubMed

Meyburg, Sven; Goryll, Michael; Moers, Jürgen; Ingebrandt, Sven; Böcker-Meffert, Simone; Lüth, Hans; Offenhäusser, Andreas

2006-01-15

A field-effect transistor (FET) for recording extracellular signals from electrogenic cells is presented. The so-called floating gate architecture combines a complementary metal oxide semiconductor (CMOS)-type n-channel transistor with an independent sensing area. This concept allows the transistor and sensing area to be optimised separately. The devices are robust and can be reused several times. The noise level of the devices was smaller than of comparable non-metallised gate FETs. In addition to the usual drift of FET devices, we observed a long-term drift that has to be controlled for future long-term measurements. The device performance for extracellular signal recording was tested using embryonic rat cardiac myocytes cultured on fibronectin-coated chips. The extracellular cell signals were recorded before and after the addition of the cardioactive isoproterenol. The signal shapes of the measured action potentials were comparable to the non-metallised gate FETs previously used in similar experiments. The fabrication of the devices involved the process steps of standard CMOS that were necessary to create n-channel transistors. The implementation of a complete CMOS process would facilitate the integration of the logical circuits necessary for signal pre-processing on a chip, which is a prerequisite for a greater number of sensor spots in future layouts.

Towards a building typology and terminology for Irish hospitals.

PubMed

Grey, T; Kennelly, S; de Freine, P; Mahon, S; Mannion, V; O'Neill, D

2017-02-01

The physical form of the hospital environment shapes the care setting and influences the relationship of the hospital to the community. Due to ongoing demographic change, evolving public health needs, and advancing medical practice, typical hospitals are frequently redeveloped, retrofitted, or expanded. It is argued that multi-disciplinary and multi-stakeholder approaches are required to ensure that hospital design matches these increasingly complex needs. To facilitate such a conversation across different disciplines, experts, and community stakeholders, it is helpful to establish a hospital typology and associated terminology as part of any collaborative process. Examine the literature around hospital design, and review the layout and overall form of a range of typical Irish acute public hospitals, to outline an associated building typology, and to establish the terminology associated with the planning and design of these hospitals in Ireland. Searches in 'Academic Search Complete', 'Compendex', 'Google', 'Google Scholar', 'JSTOR', 'PADDI', 'Science Direct', 'Scopus', 'Web of Science', and Trinity College Dublin Library. The search terms included: 'hospital design history'; 'hospital typology'; 'hospital design terminology'; and 'hospital design Ireland'. Typical hospitals are composed of different layouts due to development over time; however, various discrete building typologies can still be determined within many hospitals. This paper presents a typology illustrating distinct layout, circulation, and physical form characteristics, along with a hospital planning and design terminology of key terms and definitions. This typology and terminology define the main components of Irish hospital building design to create a shared understanding around design, and support stakeholder engagement, as part of any collaborative design process.

Luminaire layout: Design and implementation

NASA Technical Reports Server (NTRS)

Both, A. J.

1994-01-01

The information contained in this report was presented during the discussion regarding guidelines for PAR uniformity in greenhouses. The data shows a lighting uniformity analysis in a research greenhouse for rose production at the Cornell University campus. The luminaire layout was designed using the computer program Lumen-Micro. After implementation of the design, accurate measurements were taken in the greenhouse and the uniformity analysis for both the design and implementation were compared. A study of several supplemental lighting installations resulted in the following recommendations: include only the actual growing area in the lighting uniformity analysis; for growing areas up to 20 square meters, take four measurements per square meter; for growing areas above 20 square meters, take one measurement per square meter; use one of the uniformity criteria and frequency graphs to compare lighting uniformity amongst designs; and design for uniformity criterion of a least 0.75 and the fraction within +/- 15% of the average PAR value should be close to one.

Design of a gap tunable flux qubit with FastHenry

NASA Astrophysics Data System (ADS)

Akhtar, Naheed; Zheng, Yarui; Nazir, Mudassar; Wu, Yulin; Deng, Hui; Zheng, Dongning; Zhu, Xiaobo

2016-12-01

In the preparations of superconducting qubits, circuit design is a vital process because the parameters and layout of the circuit not only determine the way we address the qubits, but also strongly affect the qubit coherence properties. One of the most important circuit parameters, which needs to be carefully designed, is the mutual inductance among different parts of a superconducting circuit. In this paper we demonstrate how to design a gap-tunable flux qubit by layout design and inductance extraction using a fast field solver FastHenry. The energy spectrum of the gap-tunable flux qubit shows that the measured parameters are close to the design values. Project supported by the National Natural Science Foundation of China (Grant Nos. 11374344, 11404386, and 91321208), the National Basic Research Program of China (Grant No. 2014CB921401), and the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant No. XDB07010300).

The capture and recreation of 3D auditory scenes

NASA Astrophysics Data System (ADS)

Li, Zhiyun

The main goal of this research is to develop the theory and implement practical tools (in both software and hardware) for the capture and recreation of 3D auditory scenes. Our research is expected to have applications in virtual reality, telepresence, film, music, video games, auditory user interfaces, and sound-based surveillance. The first part of our research is concerned with sound capture via a spherical microphone array. The advantage of this array is that it can be steered into any 3D directions digitally with the same beampattern. We develop design methodologies to achieve flexible microphone layouts, optimal beampattern approximation and robustness constraint. We also design novel hemispherical and circular microphone array layouts for more spatially constrained auditory scenes. Using the captured audio, we then propose a unified and simple approach for recreating them by exploring the reciprocity principle that is satisfied between the two processes. Our approach makes the system easy to build, and practical. Using this approach, we can capture the 3D sound field by a spherical microphone array and recreate it using a spherical loudspeaker array, and ensure that the recreated sound field matches the recorded field up to a high order of spherical harmonics. For some regular or semi-regular microphone layouts, we design an efficient parallel implementation of the multi-directional spherical beamformer by using the rotational symmetries of the beampattern and of the spherical microphone array. This can be implemented in either software or hardware and easily adapted for other regular or semi-regular layouts of microphones. In addition, we extend this approach for headphone-based system. Design examples and simulation results are presented to verify our algorithms. Prototypes are built and tested in real-world auditory scenes.

Designing, developing and implementing a living snow fence program for New York state.

DOT National Transportation Integrated Search

2015-07-01

Living snow fences (LSF) are a form of passive snow control designed to mitigate blowing and drifting snow problems : on roadways. Blowing and drifting snow can increase the cost of highway maintenance and create hazardous driving : conditions when s...

Assembly Line Efficiency Improvement by Using WITNESS Simulation Software

NASA Astrophysics Data System (ADS)

Yasir, A. S. H. M.; Mohamed, N. M. Z. N.

2018-03-01

In the nowadays-competitive world, efficiencies and the productivity of the assembly line are essential in manufacturing company. This paper demonstrates the study of the existing production line performance. The actual cycle time observed and recorded during the working process. The current layout was designed and analysed using Witness simulation software. The productivity and effectiveness for every single operator are measured to determine the operator idle time and busy time. Two new alternatives layout were proposed and analysed by using Witness simulation software to improve the performance of production activities. This research provided valuable and better understanding of production effectiveness by adjusting the line balancing. After analysing the data, simulation result from the current layout and the proposed plan later been tabulated to compare the improved efficiency and productivity. The proposed design plan has shown an increase in yield and productivity compared to the current arrangement. This research has been carried out in company XYZ, which is one of the automotive premises in Pahang, Malaysia.

Buckling in serpentine microstructures and applications in elastomer-supported ultra-stretchable electronics with high areal coverage

PubMed Central

Zhang, Yihui; Xu, Sheng; Fu, Haoran; Lee, Juhwan; Su, Jessica; Hwang, Keh-Chih; Rogers, John A.; Huang, Yonggang

2014-01-01

Lithographically defined electrical interconnects with thin, filamentary serpentine layouts have been widely explored for use in stretchable electronics supported by elastomeric substrates. We present a systematic and thorough study of buckling physics in such stretchable serpentine microstructures, and a strategic design of serpentine layout for ultra-stretchable electrode, via analytical models, finite element method (FEM) computations, and quantitative experiments. Both the onset of buckling and the postbuckling behaviors are examined, to determine scaling laws for the critical buckling strain and the limits of elastic behavior. Two buckling modes, namely the symmetric and anti-symmetric modes, are identified and analyzed, with experimental images and numerical results that show remarkable levels of agreement for the associated postbuckling processes. Based on these studies and an optimization in design layout, we demonstrate routes for application of serpentine interconnects in an ultra-stretchable electrode that offer, simultaneously, an areal coverage as high as 81%, and a biaxial stretchability as large as ~170%. PMID:25309616

Buckling in serpentine microstructures and applications in elastomer-supported ultra-stretchable electronics with high areal coverage.

PubMed

Zhang, Yihui; Xu, Sheng; Fu, Haoran; Lee, Juhwan; Su, Jessica; Hwang, Keh-Chih; Rogers, John A; Huang, Yonggang

2013-01-01

Lithographically defined electrical interconnects with thin, filamentary serpentine layouts have been widely explored for use in stretchable electronics supported by elastomeric substrates. We present a systematic and thorough study of buckling physics in such stretchable serpentine microstructures, and a strategic design of serpentine layout for ultra-stretchable electrode, via analytical models, finite element method (FEM) computations, and quantitative experiments. Both the onset of buckling and the postbuckling behaviors are examined, to determine scaling laws for the critical buckling strain and the limits of elastic behavior. Two buckling modes, namely the symmetric and anti-symmetric modes, are identified and analyzed, with experimental images and numerical results that show remarkable levels of agreement for the associated postbuckling processes. Based on these studies and an optimization in design layout, we demonstrate routes for application of serpentine interconnects in an ultra-stretchable electrode that offer, simultaneously, an areal coverage as high as 81%, and a biaxial stretchability as large as ~170%.

Design and Analysis of a Navigation System Using the Federated Filter

DTIC Science & Technology

1995-12-01

There are a number of different sizes for INS states in each Kalman filter. In DKFSIM 3.3, the largest available is the so-called ABIAS model, which...REPRESENTATION PARAMETERS INS States - ABIAS Model 3 Position drifts Linearized propagation driven by ECEF velocity drifts 3 Velocity drifts

Spray drift reduction test method correlation

USDA-ARS?s Scientific Manuscript database

ASTM Standard E609 Terminology Relating to Pesticides defines drift as “The physical movement of an agrochemical through the air at the time of application or soon thereafter to any non or off target site.” Since there are many commercial tank mix adjuvants designed to reduce spray drift, ASTM esta...

Improving the layout of recycling centres by use of lean production principles.

PubMed

Sundin, Erik; Björkman, Mats; Eklund, Mats; Eklund, Jörgen; Engkvist, Inga-Lill

2011-06-01

There has been increased focus on recycling in Sweden during recent years. This focus can be attributed to external environmental factors such as tougher legislation, but also to the potential gains for raw materials suppliers. Recycling centres are important components in the Swedish total recycling system. Recycling centres are manned facilities for waste collection where visitors can bring, sort and discard worn products as well as large-sized, hazardous, and electrical waste. The aim of this paper was to identify and describe the main flows and layout types at Swedish recycling centres. The aim was also to adapt and apply production theory for designing and managing recycling centre operations. More specifically, this means using lean production principles to help develop guidelines for recycling centre design and efficient control. Empirical data for this research was primarily collected through interviews and questionnaires among both visitors and employees at 16 Swedish recycling centres. Furthermore, adapted observation protocols have been used in order to explore visitor activities. There was also close collaboration with a local recycling centre company, which shared their layout experiences with the researchers in this project. The recycling centres studied had a variety of problems such as queues of visitors, overloading of material and improper sorting. The study shows that in order to decrease the problems, the recycling centres should be designed and managed according to lean production principles, i.e. through choosing more suitable layout choices with visible and linear flows, providing better visitor information, and providing suitable technical equipment. Improvements can be achieved through proper planning of the layout and control of the flow of vehicles, with the result of increased efficiency and capacity, shorter visits, and cleaner waste fractions. The benefits of a lean production mindset include increased visitor capacity, waste flexibility, improved sorting quality, shorter time for visits and improved working conditions. Copyright © 2011 Elsevier Ltd. All rights reserved.

Range pattern matching with layer operations and continuous refinements

NASA Astrophysics Data System (ADS)

Tseng, I.-Lun; Lee, Zhao Chuan; Li, Yongfu; Perez, Valerio; Tripathi, Vikas; Ong, Jonathan Yoong Seang

2018-03-01

At advanced and mainstream process nodes (e.g., 7nm, 14nm, 22nm, and 55nm process nodes), lithography hotspots can exist in layouts of integrated circuits even if the layouts pass design rule checking (DRC). Existence of lithography hotspots in a layout can cause manufacturability issues, which can result in yield losses of manufactured integrated circuits. In order to detect lithography hotspots existing in physical layouts, pattern matching (PM) algorithms and commercial PM tools have been developed. However, there are still needs to use DRC tools to perform PM operations. In this paper, we propose a PM synthesis methodology, which uses a continuous refinement technique, for the automatic synthesis of a given lithography hotspot pattern into a DRC deck, which consists of layer operation commands, so that an equivalent PM operation can be performed by executing the synthesized deck with the use of a DRC tool. Note that the proposed methodology can deal with not only exact patterns, but also range patterns. Also, lithography hotspot patterns containing multiple layers can be processed. Experimental results show that the proposed methodology can accurately and efficiently detect lithography hotspots in physical layouts.

Binary mesh partitioning for cache-efficient visualization.

PubMed

Tchiboukdjian, Marc; Danjean, Vincent; Raffin, Bruno

2010-01-01

One important bottleneck when visualizing large data sets is the data transfer between processor and memory. Cache-aware (CA) and cache-oblivious (CO) algorithms take into consideration the memory hierarchy to design cache efficient algorithms. CO approaches have the advantage to adapt to unknown and varying memory hierarchies. Recent CA and CO algorithms developed for 3D mesh layouts significantly improve performance of previous approaches, but they lack of theoretical performance guarantees. We present in this paper a {\\schmi O}(N\\log N) algorithm to compute a CO layout for unstructured but well shaped meshes. We prove that a coherent traversal of a N-size mesh in dimension d induces less than N/B+{\\schmi O}(N/M;{1/d}) cache-misses where B and M are the block size and the cache size, respectively. Experiments show that our layout computation is faster and significantly less memory consuming than the best known CO algorithm. Performance is comparable to this algorithm for classical visualization algorithm access patterns, or better when the BSP tree produced while computing the layout is used as an acceleration data structure adjusted to the layout. We also show that cache oblivious approaches lead to significant performance increases on recent GPU architectures.

Optimising web site designs for people with learning disabilities

PubMed Central

Williams, Peter; Hennig, Christian

2015-01-01

Much relevant internet-mediated information is inaccessible to people with learning disabilities because of difficulties in navigating the web. This paper reports on the methods undertaken to determine how information can be optimally presented for this cohort. Qualitative work is outlined where attributes relating to site layout affecting usability were elicited. A study comparing web sites of different design layouts exhibiting these attributes is discussed, with the emphasis on methodology. Eight interfaces were compared using various combinations of menu position (vertical or horizontal), text size and the absence or presence of images to determine which attributes of a site have the greatest performance impact. Study participants were also asked for their preferences, via a ‘smiley-face’ rating scale and simple interviews. ‘Acquiescence bias’ was minimised by avoiding polar (‘yes/no’) interrogatives, achieved by asking participants to compare layouts (such as horizontal versus vertical menu), with reasons coaxed from those able to articulate them. Preferred designs were for large text and images. This was the reverse of those facilitating fastest retrieval times, a discrepancy due to preferences being judged on aesthetic considerations. Design recommendations that reconcile preference and performance findings are offered. These include using a horizontal menu, juxtaposing images and text, and reducing text from sentences to phrases, thus facilitating preferred large text without increasing task times. PMID:26097431

Human factors engineering approaches to patient identification armband design.

PubMed

Probst, C Adam; Wolf, Laurie; Bollini, Mara; Xiao, Yan

2016-01-01

The task of patient identification is performed many times each day by nurses and other members of the care team. Armbands are used for both direct verification and barcode scanning during patient identification. Armbands and information layout are critical to reducing patient identification errors and dangerous workarounds. We report the effort at two large, integrated healthcare systems that employed human factors engineering approaches to the information layout design of new patient identification armbands. The different methods used illustrate potential pathways to obtain standardized armbands across healthcare systems that incorporate human factors principles. By extension, how the designs have been adopted provides examples of how to incorporate human factors engineering into key clinical processes. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Matlab based Toolkits used to Interface with Optical Design Software for NASA's James Webb Space Telescope

NASA Technical Reports Server (NTRS)

Howard, Joseph

2007-01-01

The viewgraph presentation provides an introduction to the James Webb Space Telescope (JWST). The first part provides a brief overview of Matlab toolkits including CodeV, OSLO, and Zemax Toolkits. The toolkit overview examines purpose, layout, how Matlab gets data from CodeV, function layout, and using cvHELP. The second part provides examples of use with JWST, including wavefront sensitivities and alignment simulations.

Modeling Goal-Directed User Exploration in Human-Computer Interaction

DTIC Science & Technology

2011-02-01

scent, other factors including the layout position and grouping of options in the user-interface also affect user exploration and the likelihood of...grouping of options in the user-interface also affect user exploration and the likelihood of success. This dissertation contributes a new model of goal...better inform UI design. 1.1 RESEARCH GAPS IN MODELING In addition to infoscent, the layout of the UI also affects the choices made during

Examining the Impact of Drifted Polytomous Anchor Items on Test Characteristic Curve (TCC) Linking and IRT True Score Equating. Research Report. ETS RR-12-09

ERIC Educational Resources Information Center

Li, Yanmei

2012-01-01

In a common-item (anchor) equating design, the common items should be evaluated for item parameter drift. Drifted items are often removed. For a test that contains mostly dichotomous items and only a small number of polytomous items, removing some drifted polytomous anchor items may result in anchor sets that no longer resemble mini-versions of…

21 CFR 99.103 - Mandatory statements and information.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., font, layout, contrast, graphic design, headlines, spacing, and any other technique to achieve emphasis... designed and presented in a manner that achieves emphasis or notice and is distinct from the other...

48 CFR 915.404-4-71-4 - Considerations affecting fee amounts.

Code of Federal Regulations, 2012 CFR

2012-10-01

...—Manufacturing plants involving operations requiring a high degree of design layout or process control; nuclear reactors; atomic particle accelerators; complex laboratories or industrial units especially designed for...

48 CFR 915.404-4-71-4 - Considerations affecting fee amounts.

Code of Federal Regulations, 2014 CFR

2014-10-01

...—Manufacturing plants involving operations requiring a high degree of design layout or process control; nuclear reactors; atomic particle accelerators; complex laboratories or industrial units especially designed for...

48 CFR 915.404-4-71-4 - Considerations affecting fee amounts.

Code of Federal Regulations, 2010 CFR

2010-10-01

...—Manufacturing plants involving operations requiring a high degree of design layout or process control; nuclear reactors; atomic particle accelerators; complex laboratories or industrial units especially designed for...

21 CFR 99.103 - Mandatory statements and information.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., font, layout, contrast, graphic design, headlines, spacing, and any other technique to achieve emphasis... designed and presented in a manner that achieves emphasis or notice and is distinct from the other...

21 CFR 99.103 - Mandatory statements and information.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., font, layout, contrast, graphic design, headlines, spacing, and any other technique to achieve emphasis... designed and presented in a manner that achieves emphasis or notice and is distinct from the other...

48 CFR 915.404-4-71-4 - Considerations affecting fee amounts.

Code of Federal Regulations, 2011 CFR

2011-10-01

...—Manufacturing plants involving operations requiring a high degree of design layout or process control; nuclear reactors; atomic particle accelerators; complex laboratories or industrial units especially designed for...

48 CFR 915.404-4-71-4 - Considerations affecting fee amounts.

Code of Federal Regulations, 2013 CFR

2013-10-01

...—Manufacturing plants involving operations requiring a high degree of design layout or process control; nuclear reactors; atomic particle accelerators; complex laboratories or industrial units especially designed for...

21 CFR 99.103 - Mandatory statements and information.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., font, layout, contrast, graphic design, headlines, spacing, and any other technique to achieve emphasis... designed and presented in a manner that achieves emphasis or notice and is distinct from the other...

21 CFR 99.103 - Mandatory statements and information.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., font, layout, contrast, graphic design, headlines, spacing, and any other technique to achieve emphasis... designed and presented in a manner that achieves emphasis or notice and is distinct from the other...

Ryan Beach | NREL

Science.gov Websites

team. His primary responsibilities include mechanical component design, test instrumentation and layout design, and data analysis for static and fatigue tests on full-scale wind turbine blades. Education B.S

Methodology of shell structure reinforcement layout optimization

NASA Astrophysics Data System (ADS)

Szafrański, Tomasz; Małachowski, Jerzy; Damaziak, Krzysztof

2018-01-01

This paper presents an optimization process of a reinforced shell diffuser intended for a small wind turbine (rated power of 3 kW). The diffuser structure consists of multiple reinforcement and metal skin. This kind of structure is suitable for optimization in terms of selection of reinforcement density, stringers cross sections, sheet thickness, etc. The optimisation approach assumes the reduction of the amount of work to be done between the optimization process and the final product design. The proposed optimization methodology is based on application of a genetic algorithm to generate the optimal reinforcement layout. The obtained results are the basis for modifying the existing Small Wind Turbine (SWT) design.

Electro-optic architecture for servicing sensors and actuators in advanced aircraft propulsion systems

NASA Technical Reports Server (NTRS)

Poppel, G. L.; Glasheen, W. M.

1989-01-01

A detailed design of a fiber optic propulsion control system, integrating favored sensors and electro-optics architecture is presented. Layouts, schematics, and sensor lists describe an advanced fighter engine system model. Components and attributes of candidate fiber optic sensors are identified, and evaluation criteria are used in a trade study resulting in favored sensors for each measurand. System architectural ground rules were applied to accomplish an electro-optics architecture for the favored sensors. A key result was a considerable reduction in signal conductors. Drawings, schematics, specifications, and printed circuit board layouts describe the detailed system design, including application of a planar optical waveguide interface.

Overview of the Westinghouse Small Modular Reactor building layout

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronje, J. M.; Van Wyk, J. J.; Memmott, M. J.

The Westinghouse Small Modular Reactor (SMR) is an 800 MWt (>225 MWe) integral pressurized water reactor (iPWR), in which all of the components typically associated with the nuclear steam supply system (NSSS) of a nuclear power plant are incorporated within a single reactor pressure vessel. This paper is the third in a series of four papers, which describe the design and functionality of the Westinghouse SMR. It focuses in particular upon the plant building layout and modular design of the Westinghouse SMR. In the development of small modular reactors, the building layout is an area where the safety of themore » plant can be improved by applying new design approaches. This paper will present an overview of the Westinghouse SMR building layout and indicate how the design features improve the safety and robustness of the plant. The Westinghouse SMR is designed with no shared systems between individual reactor units. The main buildings inside the security fence are the nuclear island, the rad-waste building, the annex building, and the turbine building. All safety related equipment is located in the nuclear island, which is a seismic class 1 building. To further enhance the safety and robustness of the design, the reactor, containment, and most of the safety related equipment are located below grade on the nuclear island. This reduces the possibility of severe damage from external threats or natural disasters. Two safety related ultimate heat sink (UHS) water tanks that are used for decay heat removal are located above grade, but are redundant and physically separated as far as possible for improved safety. The reactor and containment vessel are located below grade in the center of the nuclear island. The rad-waste and other radioactive systems are located on the bottom floors to limit the radiation exposure to personnel. The Westinghouse SMR safety trains are completely separated into four unconnected quadrants of the building, with access between quadrants only allowed above grade. This is an improvement to conventional reactor design since it prevents failures of multiple trains during floods or fires and other external events. The main control room is located below grade, with a remote shutdown room in a different quadrant. All defense in depth systems are placed on the nuclear island, primarily above grade, while the safety systems are located on lower floors. The economics of the Westinghouse SMR challenges the established approach of large Light Water Reactors (LWR) that utilized the economies of scale to reach economic competitiveness. To serve the market expectation of smaller capital investment and cost competitive energy, a modular design approach is implemented within the Westinghouse SMR. The Westinghouse SMR building layout integrates the three basic design constraints of modularization; transportation, handling and module-joining technology. (authors)« less

The study on the effect of pattern density distribution on the STI CMP process

NASA Astrophysics Data System (ADS)

Sub, Yoon Myung; Hian, Bernard Yap Tzen; Fong, Lee It; Anak, Philip Menit; Minhar, Ariffin Bin; Wui, Tan Kim; Kim, Melvin Phua Twang; Jin, Looi Hui; Min, Foo Thai

2017-08-01

The effects of pattern density on CMP characteristics were investigated using specially designed wafer for the characterization of pattern-dependencies in STI CMP [1]. The purpose of this study is to investigate the planarization behavior based on a direct STI CMP used in cerium (CeO2) based slurry system in terms of pattern density variation. The minimal design rule (DR) of 180nm generation technology node was adopted for the mask layout. The mask was successfully applied for evaluation of a cerium (CeO2) abrasive based direct STI CMP process. In this study, we described a planarization behavior of the loading-effects of pattern density variation which were characterized with layout pattern density and pitch variations using masks mentioned above. Furthermore, the characterizing pattern dependent on the variations of the dimensions and spacing features, in thickness remaining after CMP, were analyzed and evaluated. The goal was to establish a concept of library method which will be used to generate design rules reducing the probability of CMP-related failures. Details of the characterization were measured in various layouts showing different pattern density ranges and the effects of pattern density on STI CMP has been discussed in this paper.

Post-decomposition optimizations using pattern matching and rule-based clustering for multi-patterning technology

NASA Astrophysics Data System (ADS)

Wang, Lynn T.-N.; Madhavan, Sriram

2018-03-01

A pattern matching and rule-based polygon clustering methodology with DFM scoring is proposed to detect decomposition-induced manufacturability detractors and fix the layout designs prior to manufacturing. A pattern matcher scans the layout for pre-characterized patterns from a library. If a pattern were detected, rule-based clustering identifies the neighboring polygons that interact with those captured by the pattern. Then, DFM scores are computed for the possible layout fixes: the fix with the best score is applied. The proposed methodology was applied to two 20nm products with a chip area of 11 mm2 on the metal 2 layer. All the hotspots were resolved. The number of DFM spacing violations decreased by 7-15%.

Office ergonomics: deficiencies in computer workstation design.

PubMed

Shikdar, Ashraf A; Al-Kindi, Mahmoud A

2007-01-01

The objective of this research was to study and identify ergonomic deficiencies in computer workstation design in typical offices. Physical measurements and a questionnaire were used to study 40 workstations. Major ergonomic deficiencies were found in physical design and layout of the workstations, employee postures, work practices, and training. The consequences in terms of user health and other problems were significant. Forty-five percent of the employees used nonadjustable chairs, 48% of computers faced windows, 90% of the employees used computers more than 4 hrs/day, 45% of the employees adopted bent and unsupported back postures, and 20% used office tables for computers. Major problems reported were eyestrain (58%), shoulder pain (45%), back pain (43%), arm pain (35%), wrist pain (30%), and neck pain (30%). These results indicated serious ergonomic deficiencies in office computer workstation design, layout, and usage. Strategies to reduce or eliminate ergonomic deficiencies in computer workstation design were suggested.

New Baseline Design of the ILC RTML System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seletskiy, S.; Kapin, V. V.; Solyak, N.

2012-05-01

The new ILC baseline was proposed in 2009 (Strawman baseline - SB2009) to minimize cost of the machine and accommodate many changes made in the design of the accelerator systems. The biggest changes are made in the central area, where BDS, RTM L, DR, electron and positron sources are sharing the tunnels. A new layout of the compact DR and re-location of the electron and positron sources to the main tunnel requires a new lattice design for all beamlines in this area. The lattice design was coord inated between accelerator systems and Convention Facility and Siting (CFS) group to eliminatemore » conflicts between beamlines and satisfy construction requirements. In this paper we present a new design of the RTML electron and positron lattices in the centr al area and other modifications made in the RTML line to accommodate changes to the beamline layouts.« less

The NASA computer aided design and test system

NASA Technical Reports Server (NTRS)

Gould, J. M.; Juergensen, K.

1973-01-01

A family of computer programs facilitating the design, layout, evaluation, and testing of digital electronic circuitry is described. CADAT (computer aided design and test system) is intended for use by NASA and its contractors and is aimed predominantly at providing cost effective microelectronic subsystems based on custom designed metal oxide semiconductor (MOS) large scale integrated circuits (LSIC's). CADAT software can be easily adopted by installations with a wide variety of computer hardware configurations. Its structure permits ease of update to more powerful component programs and to newly emerging LSIC technologies. The components of the CADAT system are described stressing the interaction of programs rather than detail of coding or algorithms. The CADAT system provides computer aids to derive and document the design intent, includes powerful automatic layout software, permits detailed geometry checks and performance simulation based on mask data, and furnishes test pattern sequences for hardware testing.

A Close Loop Low-Power and High Speed 130 nm CMOS Sample and Hold Circuit Based on Switched Capacitor for ADC Module

NASA Astrophysics Data System (ADS)

Nasir, Z.; Ruslan, S. H.

2017-08-01

A sample and hold (S/H) block is typically used as an analogue to digital interface in the analogue to digital converter (ADC) system. Since ADC is widely used in processing signals, the power consumption of the ADC must be lowered to conserve energy. Therefore the S/H circuit must be of a low powered too. Sampling phase and hold phase are the two phases of the operation cycle of the S/H circuit. Switched capacitor (SC) techniques have been developed in order to allow the integration on a single silicon chip of both digital and analogue functions. By controlling switches around the SC, the SC circuit works by passing charge into and out of a capacitor. SC circuits are suitable for on chip implementations because they replace a resistor with switches and capacitors. In this research, a closed-loop sample and hold circuit based on SC is designed and simulated with Cadence EDA tools. The schematic, layout, and simulation of the circuit is done using generic Silterra 130 nm technology file. All the analysis is done using Virtuoso Analog Design Environment. Layout and schematic are drawn using Virtuoso Schematic Editor and Virtuoso Layout Editor, Calibre is used for post layout simulation. The closed loop S/H circuit based on SC is successfully designed and able to sample and hold the analogue input waveform. The power consumption of the circuit is 0.919 mW and the propagation delay is 64.96 ps.

User Interface Design in Medical Distributed Web Applications.

PubMed

Serban, Alexandru; Crisan-Vida, Mihaela; Mada, Leonard; Stoicu-Tivadar, Lacramioara

2016-01-01

User interfaces are important to facilitate easy learning and operating with an IT application especially in the medical world. An easy to use interface has to be simple and to customize the user needs and mode of operation. The technology in the background is an important tool to accomplish this. The present work aims to creating a web interface using specific technology (HTML table design combined with CSS3) to provide an optimized responsive interface for a complex web application. In the first phase, the current icMED web medical application layout is analyzed, and its structure is designed using specific tools, on source files. In the second phase, a new graphic adaptable interface to different mobile terminals is proposed, (using HTML table design (TD) and CSS3 method) that uses no source files, just lines of code for layout design, improving the interaction in terms of speed and simplicity. For a complex medical software application a new prototype layout was designed and developed using HTML tables. The method uses a CSS code with only CSS classes applied to one or multiple HTML table elements, instead of CSS styles that can be applied to just one DIV tag at once. The technique has the advantage of a simplified CSS code, and a better adaptability to different media resolutions compared to DIV-CSS style method. The presented work is a proof that adaptive web interfaces can be developed just using and combining different types of design methods and technologies, using HTML table design, resulting in a simpler to learn and use interface, suitable for healthcare services.

New central drift chamber for the MARK II at SLC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartelt, J.E.

A new central drift chamber has been constructed for the Mark II detector for use at the new SLAC Linear Collider (SLC). The design of the chamber is based on a multi-sense-wire cell of the jet chamber type. In addition to drift-time measurements, pulse-height measurements from the sense wires provide electron-hadron separation by dE/dx. The chamber has been tested in operation at PEP before its move to the SLC. The design and construction are described, and measurements from the new chamber are presented.

Seismic Design of ITER Component Cooling Water System-1 Piping

NASA Astrophysics Data System (ADS)

Singh, Aditya P.; Jadhav, Mahesh; Sharma, Lalit K.; Gupta, Dinesh K.; Patel, Nirav; Ranjan, Rakesh; Gohil, Guman; Patel, Hiren; Dangi, Jinendra; Kumar, Mohit; Kumar, A. G. A.

2017-04-01

The successful performance of ITER machine very much depends upon the effective removal of heat from the in-vessel components and other auxiliary systems during Tokamak operation. This objective will be accomplished by the design of an effective Cooling Water System (CWS). The optimized piping layout design is an important element in CWS design and is one of the major design challenges owing to the factors of large thermal expansion and seismic accelerations; considering safety, accessibility and maintainability aspects. An important sub-system of ITER CWS, Component Cooling Water System-1 (CCWS-1) has very large diameter of pipes up to DN1600 with many intersections to fulfill the process flow requirements of clients for heat removal. Pipe intersection is the weakest link in the layout due to high stress intensification factor. CCWS-1 piping up to secondary confinement isolation valves as well as in-between these isolation valves need to survive a Seismic Level-2 (SL-2) earthquake during the Tokamak operation period to ensure structural stability of the system in the Safe Shutdown Earthquake (SSE) event. This paper presents the design, qualification and optimization of layout of ITER CCWS-1 loop to withstand SSE event combined with sustained and thermal loads as per the load combinations defined by ITER and allowable limits as per ASME B31.3, This paper also highlights the Modal and Response Spectrum Analyses done to find out the natural frequency and system behavior during the seismic event.

Designing the Electronic Classroom: Applying Learning Theory and Ergonomic Design Principles.

ERIC Educational Resources Information Center

Emmons, Mark; Wilkinson, Frances C.

2001-01-01

Applies learning theory and ergonomic principles to the design of effective learning environments for library instruction. Discusses features of electronic classroom ergonomics, including the ergonomics of physical space, environmental factors, and workstations; and includes classroom layouts. (Author/LRW)

Study of LED layout in indoor visible light communication and performance analysis

NASA Astrophysics Data System (ADS)

Wang, Jiaan; Che, Ying; Wang, Xinlan; Guo, Linyang; Li, Jing

2017-10-01

Light emitting diodes(LED) could provide both illumination and data communication in indoor visible light communication(VLC) that owns the modulation bandwith from several from several MHz to seneral hundreds of MHz. The layout of LED plays an important role in maintaining a steady optical power distribution over the receiving plane. The existing rectangular LED layout does not provide a full coverage on the receiving plane leaving receiving optical power outage area, which in turn affects the best performance of the VLC system. This paper design a circular layout scheme of LED in 5mX5mX3m room based on the criterion of the illumination minimum mean square deviation. The influence of the distribution of the intensity of illumination with the radius of 1m and 1.5m,for including the wall reflection and not including the wall reflection, and make a comparison with rectangular LED layout of illumination distribution, when the number of LEDs with rectangular layout as same as circular layout. Including the number of LEDs are 4 and 16.For a specific simulation parameters as following:height of receiving plane is 0.85m,a single LEDs is composed of 60X60 LED chips, the parameters of a single chip is that transmitting power is 20mW,center luminous intensity is 0.73cd.semiangle at half power is 70deg.The parameters of concentrator is that photodiode area is 1cm2,photodiode responsivity is 0.4,field of view at the receiver is 85deg.Other parameters are that reflective index of concentrator is 1.5,reflectivity of wall is 0.8.Circular layout and rectangular layout are analyzed through simulation of the received optical power distribution, signal noise ratio distribution in non line of sight(including the wall reflection) and line of sight(not including the wall reflection),when the number of the LED is different. It is clear from the results that the received optical power distribution of non line of sight is better than line of sight, when the number of the LED are same, but the signal noise ratio distribution is decreased result of the reflection of the wall. It is found that the received optical power of circular layout is better than the received optical power distribution of rectangulr layout, and circular layout is a good solution that add the received optical power at the 4 corners of room, improve the system ability of communication, when making a contrast of rectangular lyout with circular layout,at the same time,the fluctuate of circular layout's signal to noise ratio of is smller than rectangular layuot.The radius of circular layout or the location of rectangular layout is keeping, the received optical power of receiving plane is increased, by adding the number of LED,in the meantime, the interference between LED light source also increase. But the increase of the circular layout radius when the number of LED remain the same is helpful to reduce the inter symbol interference that work out between LED each other, enhance the system signal noise ratio. In this paper, the results of the reaearch provides a new idea for indoor visible light communication with non-standard room (Size of room is not 5mX5mX3m), at the same time, provides guiding significance for future setting up the indoor visible light communication links.

The test of the layout of polarimeter "UFP" on the telescope AZT-2

NASA Astrophysics Data System (ADS)

Levchenko, T. A.; Nevodovskyi, P. V.; Vidmachenko, A. P.; Morozhenko, O. V.; Saryboha, H. V.; Zbrutsky, O. V.; Ivakhiv, O. V.

2016-05-01

Main Astronomical Observatory of NAS of Ukraine in cooperation with the National Technical University of Ukraine "KPI" and National University "Lviv Polytechnic" for a long time working on the design of an optical polarimeter to study of the stratospheric layer of the Earth using of orbital satellite. During this time, was accumulated a large experience of such work, and was established a layout of compact ultraviolet polarimeter (UFP) on board of satellite

1D design style implications for mask making and CEBL

NASA Astrophysics Data System (ADS)

Smayling, Michael C.

2013-09-01

At advanced nodes, CMOS logic is being designed in a highly regular design style because of the resolution limitations of optical lithography equipment. Logic and memory layouts using 1D Gridded Design Rules (GDR) have been demonstrated to nodes beyond 12nm.[1-4] Smaller nodes will require the same regular layout style but with multiple patterning for critical layers. One of the significant advantages of 1D GDR is the ease of splitting layouts into lines and cuts. A lines and cuts approach has been used to achieve good pattern fidelity and process margin to below 12nm.[4] Line scaling with excellent line-edge roughness (LER) has been demonstrated with self-aligned spacer processing.[5] This change in design style has important implications for mask making: • The complexity of the masks will be greatly reduced from what would be required for 2D designs with very complex OPC or inverse lithography corrections. • The number of masks will initially increase, as for conventional multiple patterning. But in the case of 1D design, there are future options for mask count reduction. • The line masks will remain simple, with little or no OPC, at pitches (1x) above 80nm. This provides an excellent opportunity for continual improvement of line CD and LER. The line pattern will be processed through a self-aligned pitch division sequence to divide pitch by 2 or by 4. • The cut masks can be done with "simple OPC" as demonstrated to beyond 12nm.[6] Multiple simple cut masks may be required at advanced nodes. "Coloring" has been demonstrated to below 12nm for two colors and to 8nm for three colors. • Cut/hole masks will eventually be replaced by e-beam direct write using complementary e-beam lithography (CEBL).[7-11] This transition is gated by the availability of multiple column e-beam systems with throughput adequate for high- volume manufacturing. A brief description of 1D and 2D design styles will be presented, followed by examples of 1D layouts. Mask complexity for 1D layouts patterned directly will be compared to mask complexity for lines and cuts at nodes larger than 20nm. No such comparison is possible below 20nm since single-patterning does not work below ~80nm pitch using optical exposure tools. Also discussed will be recently published wafer results for line patterns with pitch division by-2 and by-4 at sub-12nm nodes, plus examples of post-etch results for 1D patterns done with cut masks and compared to cuts exposed by a single-column e-beam direct write system.

Designing Clinical Space for the Delivery of Integrated Behavioral Health and Primary Care.

PubMed

Gunn, Rose; Davis, Melinda M; Hall, Jennifer; Heintzman, John; Muench, John; Smeds, Brianna; Miller, Benjamin F; Miller, William L; Gilchrist, Emma; Brown Levey, Shandra; Brown, Jacqueline; Wise Romero, Pam; Cohen, Deborah J

2015-01-01

This study sought to describe features of the physical space in which practices integrating primary care and behavioral health care work and to identify the arrangements that enable integration of care. We conducted an observational study of 19 diverse practices located across the United States. Practice-level data included field notes from 2-4-day site visits, transcripts from semistructured interviews with clinicians and clinical staff, online implementation diary posts, and facility photographs. A multidisciplinary team used a 4-stage, systematic approach to analyze data and identify how physical layout enabled the work of integrated care teams. Two dominant spatial layouts emerged across practices: type-1 layouts were characterized by having primary care clinicians (PCCs) and behavioral health clinicians (BHCs) located in separate work areas, and type-2 layouts had BHCs and PCCs sharing work space. We describe these layouts and the influence they have on situational awareness, interprofessional "bumpability," and opportunities for on-the-fly communication. We observed BHCs and PCCs engaging in more face-to-face methods for coordinating integrated care for patients in type 2 layouts (41.5% of observed encounters vs 11.7%; P < .05). We show that practices needed to strike a balance between professional proximity and private work areas to accomplish job tasks. Private workspace was needed for focused work, to see patients, and for consults between clinicians and clinical staff. We describe the ways practices modified and built new space and provide 2 recommended layouts for practices integrating care based on study findings. Physical layout and positioning of professionals' workspace is an important consideration in practices implementing integrated care. Clinicians, researchers, and health-care administrators are encouraged to consider the role of professional proximity and private working space when creating new facilities or redesigning existing space to foster delivery of integrated behavioral health and primary care. © Copyright 2015 by the American Board of Family Medicine.

RF cavity design and qualification for proton accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teotia, Vikas; Malhotra, Sanjay; Ukarde, Priti

Alvarez type Drift Tube Linac (DTL) is used for acceleration of proton beam in low energy section of beta ranging from 0.04 to 0.40. DTL is cylindrical RF cavity resonating in TM010 mode at 352.21 MHz frequency. It consists of array of drift tubes arranged ensuring that DTL centre and Drift Tube centre are concentric. The Drift Tubes also houses Permanent Magnet Quadrupole for transverse focusing of proton beam. A twelve cell prototype of DTL section is designed, developed and fabricated at Bhabha Atomic Research Centre, Trombay. Complete DTL accelerator consists of eight such DTL sections. High frequency microwave simulationsmore » are carried out in SOPRANO, vector fields and COMSOL simulation software. This prototype DTL is 1640.56 mm long cavity with 520 mm ID, 600 mm OD and consists of eleven Drift Tubes, two RF end flanges, three slug tuners, six post couplers, three RF field monitors, one RF waveguide coupler, two DN100 vacuum flanges and DTL tank platform with alignment features. Girder based Drift tube mounting arrangement utilizing uncompressing energy of disc springs for optimum combo RF-vacuum seal compression is worked out and implemented. This paper discusses design of this RF vacuum cavity operating at high accelerating field gradient in ultra-high vacuum. Detailed vacuum design and results of RF and vacuum qualifications are discussed. Results on mechanical accuracy achieved on scaled pre-prototype are also presented. Paper summarizes the engineering developments carried out for this RF cavity and brings out the future activities proposed in indigenous development of high gradient RF cavities for ion accelerators. (author)« less

32 CFR 223.7 - Procedures-determination of DoD UCNI.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Detection and Security Alarm Systems. (i) Information on the layout or design of security and alarm systems...) Frequency and schedule of DoD SNM inventories. (3) Facility Description. (i) Maps, conceptual design, and...

32 CFR 223.7 - Procedures-determination of DoD UCNI.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Detection and Security Alarm Systems. (i) Information on the layout or design of security and alarm systems...) Frequency and schedule of DoD SNM inventories. (3) Facility Description. (i) Maps, conceptual design, and...

Spatial layout optimization design of multi-type LEDs lighting source based on photoelectrothermal coupling theory

NASA Astrophysics Data System (ADS)

Xue, Lingyun; Li, Guang; Chen, Qingguang; Rao, Huanle; Xu, Ping

2018-03-01

Multiple LED-based spectral synthesis technology has been widely used in the fields of solar simulator, color mixing, and artificial lighting of plant factory and so on. Generally, amounts of LEDs are spatially arranged with compact layout to obtain the high power density output. Mutual thermal spreading among LEDs will produce the coupled thermal effect which will additionally increase the junction temperature of LED. Affected by the Photoelectric thermal coupling effect of LED, the spectrum of LED will shift and luminous efficiency will decrease. Correspondingly, the spectral synthesis result will mismatch. Therefore, thermal management of LED spatial layout plays an important role for multi-LEDs light source system. In the paper, the thermal dissipation network topology model considering the mutual thermal spreading effect among the LEDs is proposed for multi-LEDs system with various types of power. The junction temperature increment cased by the thermal coupling has the great relation with the spatial arrangement. To minimize the thermal coupling effect, an optimized method of LED spatial layout for the specific light source structure is presented and analyzed. The results showed that layout of LED with high-power are arranged in the corner and low-power in the center. Finally, according to this method, it is convenient to determine the spatial layout of LEDs in a system having any kind of light source structure, and has the advantages of being universally applicable to facilitate adjustment.

Measurement of Spray Drift with a Specifically Designed Lidar System.

PubMed

Gregorio, Eduard; Torrent, Xavier; Planas de Martí, Santiago; Solanelles, Francesc; Sanz, Ricardo; Rocadenbosch, Francesc; Masip, Joan; Ribes-Dasi, Manel; Rosell-Polo, Joan R

2016-04-08

Field measurements of spray drift are usually carried out by passive collectors and tracers. However, these methods are labour- and time-intensive and only provide point- and time-integrated measurements. Unlike these methods, the light detection and ranging (lidar) technique allows real-time measurements, obtaining information with temporal and spatial resolution. Recently, the authors have developed the first eye-safe lidar system specifically designed for spray drift monitoring. This prototype is based on a 1534 nm erbium-doped glass laser and an 80 mm diameter telescope, has scanning capability, and is easily transportable. This paper presents the results of the first experimental campaign carried out with this instrument. High coefficients of determination (R² > 0.85) were observed by comparing lidar measurements of the spray drift with those obtained by horizontal collectors. Furthermore, the lidar system allowed an assessment of the drift reduction potential (DRP) when comparing low-drift nozzles with standard ones, resulting in a DRP of 57% (preliminary result) for the tested nozzles. The lidar system was also used for monitoring the evolution of the spray flux over the canopy and to generate 2-D images of these plumes. The developed instrument is an advantageous alternative to passive collectors and opens the possibility of new methods for field measurement of spray drift.

Design to Improve Visibility: Impact of Corridor Width and Unit Shape.

PubMed

Hadi, Khatereh; Zimring, Craig

2016-07-01

This study analyzes 10 intensive care units (ICUs) to understand the associations between design features of space layout and nurse-to-patient visibility parameters. Previous studies have explored how different hospital units vary in their visibility relations and how such varied visibility relations result in different nurse behaviors toward patients. However, more limited research has examined the specific design attributes of the layouts that determine the varied visibility relations in the unit. Changes in size, geometry, or other attributes of design elements in nursing units, which might affect patient observation opportunities, require more research. This article reviews the literature to indicate evidence for the impact of hospital unit design on nurse/patient visibility relations and to identify design parameters shown to affect visibility. It further focuses on 10 ICUs to investigate how different layouts diverge regarding their visibility relations using a set of metrics developed by other researchers. Shape geometry and corridor width, as two selected design features, are compared. Corridor width and shape characteristics of ICUs are positively correlated with visibility. Results suggest that floor plans, which are repeatedly broken down into smaller convex (higher convex fragmentation values), or units, which have longer distances between their rooms or between their two opposite ends (longer relative grid distances), might have lower visibility levels across the unit. The findings of this study also suggest that wider corridors positively affect visibility of patient rooms. Changes in overall shape configuration and corridor width of nursing units may have important effects on patient observation and monitoring opportunities. © The Author(s) 2016.

Expert system for generating initial layouts of zoom systems with multiple moving lens groups

NASA Astrophysics Data System (ADS)

Cheng, Xuemin; Wang, Yongtian; Hao, Qun; Sasián, José M.

2005-01-01

An expert system is developed for the automatic generation of initial layouts for the design of zoom systems with multiple moving lens groups. The Gaussian parameters of the zoom system are optimized using the damped-least-squares method to achieve smooth zoom cam curves, with the f-number of each lens group in the zoom system constrained to a rational value. Then each lens group is selected automatically from a database according to its range of f-number, field of view, and magnification ratio as it is used in the zoom system. The lens group database is established from the results of analyzing thousands of zoom lens patents. Design examples are given, which show that the scheme is a practical approach to generate starting points for zoom lens design.

Twinlist: novel user interface designs for medication reconciliation.

PubMed

Plaisant, Catherine; Chao, Tiffany; Wu, Johnny; Hettinger, A Zach; Herskovic, Jorge R; Johnson, Todd R; Bernstam, Elmer V; Markowitz, Eliz; Powsner, Seth; Shneiderman, Ben

2013-01-01

Medication reconciliation is an important and complex task for which careful user interface design has the potential to help reduce errors and improve quality of care. In this paper we focus on the hospital discharge scenario and first describe a novel interface called Twinlist. Twinlist illustrates the novel use of spatial layout combined with multi-step animation, to help medical providers see what is different and what is similar between the lists (e.g., intake list and hospital list), and rapidly choose the drugs they want to include in the reconciled list. We then describe a series of variant designs and discuss their comparative advantages and disadvantages. Finally we report on a pilot study that suggests that animation might help users learn new spatial layouts such as the one used in Twinlist.

Sources and control of instrumental drift in the surface forces apparatus

NASA Astrophysics Data System (ADS)

Heuberger, M.; Zäch, M.; Spencer, N. D.

2000-12-01

Instrumental drift in the surface forces apparatus (SFA) has been carefully scrutinized. A diversity of different contributions with different characteristic time constants could be distinguished. The face seal of the functional attachment was identified as a potential weak point in the mechanical loop of the instrument. We compared drift in three different design variants and found that the drift rate may vary over four orders of magnitude. We believe that the presented results are applicable to a number of different SFA types.

Built-in electric field thickness design for betavoltaic batteries

NASA Astrophysics Data System (ADS)

Haiyang, Chen; Darang, Li; Jianhua, Yin; Shengguo, Cai

2011-09-01

Isotope source energy deposition along the thickness direction of a semiconductor is calculated, based upon which an ideal short current is evaluated for betavoltaic batteries. Electron-hole pair recombination and drifting length in a PN junction built-in electric field are extracted by comparing the measured short currents with the ideal short currents. A built-in electric field thickness design principle is proposed for betavoltaic batteries: after measuring the energy deposition depth and the carrier drift length, the shorter one should then be chosen as the built-in electric field thickness. If the energy deposition depth is much larger than the carrier drift length, a multi-junction is preferred in betavoltaic batteries and the number of the junctions should be the value of the deposition depth divided by the drift length.

22 CFR 120.41 - Specially designed.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., integration design, layouts. Note 3 to paragraph (b)(3): Commodities in “production” that are subsequently... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Specially designed. 120.41 Section 120.41... § 120.41 Specially designed. (a) Except for commodities or software described in paragraph (b) of this...

What Is Information Design?

ERIC Educational Resources Information Center

Redish, Janice C. (Ginny)

2000-01-01

Defines two meanings of information design: the overall process of developing a successful document; and the way the information is presented on the screen (layout, typography, color, and so forth). Discusses the future importance of both of these meanings of information design, in terms of design for the web and single-sources (planning…

A Sharp methodology for VLSI layout

NASA Astrophysics Data System (ADS)

Bapat, Shekhar

1993-01-01

The layout problem for VLSI circuits is recognized as a very difficult problem and has been traditionally decomposed into the several seemingly independent sub-problems of placement, global routing, and detailed routing. Although this structure achieves a reduction in programming complexity, it is also typically accompanied by a reduction in solution quality. Most current placement research recognizes that the separation is artificial, and that the placement and routing problems should be solved ideally in tandem. We propose a new interconnection model, Sharp and an associated partitioning algorithm. The Sharp interconnection model uses a partitioning shape that roughly resembles the musical sharp 'number sign' and makes extensive use of pre-computed rectilinear Steiner trees. The model is designed to generate strategic routing information along with the partitioning results. Additionally, the Sharp model also generates estimates of the routing congestion. We also propose the Sharp layout heuristic that solves the layout problem in its entirety. The Sharp layout heuristic makes extensive use of the Sharp partitioning model. The use of precomputed Steiner tree forms enables the method to model accurately net characteristics. For example, the Steiner tree forms can model both the length of the net and more importantly its route. In fact, the tree forms are also appropriate for modeling the timing delays of nets. The Sharp heuristic works to minimize both the total layout area by minimizing total net length (thus reducing the total wiring area), and the congestion imbalances in the various channels (thus reducing the unused or wasted channel area). Our heuristic uses circuit element movements amongst the different partitioning blocks and selection of alternate minimal Steiner tree forms to achieve this goal. The objective function for the algorithm can be modified readily to include other important circuit constraints like propagation delays. The layout technique first computes a very high-level approximation of the layout solution (i.e., the positions of the circuit elements and the associated net routes). The approximate solution is alternately refined, objective function. The technique creates well defined sub-problems and offers intermediary steps that can be solved in parallel, as well as a parallel mechanism to merge the sub-problem solutions.

10 CFR 72.182 - Design for physical protection.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Physical Protection § 72.182 Design for physical protection. The design for physical protection must show the site layout and the design features provided to protect the ISFSI or MRS from sabotage. It must... 10 Energy 2 2013-01-01 2013-01-01 false Design for physical protection. 72.182 Section 72.182...

10 CFR 72.182 - Design for physical protection.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Physical Protection § 72.182 Design for physical protection. The design for physical protection must show the site layout and the design features provided to protect the ISFSI or MRS from sabotage. It must... 10 Energy 2 2010-01-01 2010-01-01 false Design for physical protection. 72.182 Section 72.182...

10 CFR 72.182 - Design for physical protection.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Physical Protection § 72.182 Design for physical protection. The design for physical protection must show the site layout and the design features provided to protect the ISFSI or MRS from sabotage. It must... 10 Energy 2 2012-01-01 2012-01-01 false Design for physical protection. 72.182 Section 72.182...

10 CFR 72.182 - Design for physical protection.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Physical Protection § 72.182 Design for physical protection. The design for physical protection must show the site layout and the design features provided to protect the ISFSI or MRS from sabotage. It must... 10 Energy 2 2014-01-01 2014-01-01 false Design for physical protection. 72.182 Section 72.182...

10 CFR 72.182 - Design for physical protection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Physical Protection § 72.182 Design for physical protection. The design for physical protection must show the site layout and the design features provided to protect the ISFSI or MRS from sabotage. It must... 10 Energy 2 2011-01-01 2011-01-01 false Design for physical protection. 72.182 Section 72.182...

Design technology co-optimization for 14/10nm metal1 double patterning layer

NASA Astrophysics Data System (ADS)

Duan, Yingli; Su, Xiaojing; Chen, Ying; Su, Yajuan; Shao, Feng; Zhang, Recco; Lei, Junjiang; Wei, Yayi

2016-03-01

Design and technology co-optimization (DTCO) can satisfy the needs of the design, generate robust design rule, and avoid unfriendly patterns at the early stage of design to ensure a high level of manufacturability of the product by the technical capability of the present process. The DTCO methodology in this paper includes design rule translation, layout analysis, model validation, hotspots classification and design rule optimization mainly. The correlation of the DTCO and double patterning (DPT) can optimize the related design rule and generate friendlier layout which meets the requirement of the 14/10nm technology node. The experiment demonstrates the methodology of DPT-compliant DTCO which is applied to a metal1 layer from the 14/10nm node. The DTCO workflow proposed in our job is an efficient solution for optimizing the design rules for 14/10 nm tech node Metal1 layer. And the paper also discussed and did the verification about how to tune the design rule of the U-shape and L-shape structures in a DPT-aware metal layer.

SCM: A method to improve network service layout efficiency with network evolution.

PubMed

Zhao, Qi; Zhang, Chuanhao; Zhao, Zheng

2017-01-01

Network services are an important component of the Internet, which are used to expand network functions for third-party developers. Network function virtualization (NFV) can improve the speed and flexibility of network service deployment. However, with the evolution of the network, network service layout may become inefficient. Regarding this problem, this paper proposes a service chain migration (SCM) method with the framework of "software defined network + network function virtualization" (SDN+NFV), which migrates service chains to adapt to network evolution and improves the efficiency of the network service layout. SCM is modeled as an integer linear programming problem and resolved via particle swarm optimization. An SCM prototype system is designed based on an SDN controller. Experiments demonstrate that SCM could reduce the network traffic cost and energy consumption efficiently.

Estimation of cyclic interstory drift capacity of steel framed structures and future applications for seismic design.

PubMed

Bojórquez, Edén; Reyes-Salazar, Alfredo; Ruiz, Sonia E; Terán-Gilmore, Amador

2014-01-01

Several studies have been devoted to calibrate damage indices for steel and reinforced concrete members with the purpose of overcoming some of the shortcomings of the parameters currently used during seismic design. Nevertheless, there is a challenge to study and calibrate the use of such indices for the practical structural evaluation of complex structures. In this paper, an energy-based damage model for multidegree-of-freedom (MDOF) steel framed structures that accounts explicitly for the effects of cumulative plastic deformation demands is used to estimate the cyclic drift capacity of steel structures. To achieve this, seismic hazard curves are used to discuss the limitations of the maximum interstory drift demand as a performance parameter to achieve adequate damage control. Then the concept of cyclic drift capacity, which incorporates information of the influence of cumulative plastic deformation demands, is introduced as an alternative for future applications of seismic design of structures subjected to long duration ground motions.

Estimation of Cyclic Interstory Drift Capacity of Steel Framed Structures and Future Applications for Seismic Design

PubMed Central

Bojórquez, Edén; Reyes-Salazar, Alfredo; Ruiz, Sonia E.; Terán-Gilmore, Amador

2014-01-01

Several studies have been devoted to calibrate damage indices for steel and reinforced concrete members with the purpose of overcoming some of the shortcomings of the parameters currently used during seismic design. Nevertheless, there is a challenge to study and calibrate the use of such indices for the practical structural evaluation of complex structures. In this paper, an energy-based damage model for multidegree-of-freedom (MDOF) steel framed structures that accounts explicitly for the effects of cumulative plastic deformation demands is used to estimate the cyclic drift capacity of steel structures. To achieve this, seismic hazard curves are used to discuss the limitations of the maximum interstory drift demand as a performance parameter to achieve adequate damage control. Then the concept of cyclic drift capacity, which incorporates information of the influence of cumulative plastic deformation demands, is introduced as an alternative for future applications of seismic design of structures subjected to long duration ground motions. PMID:25089288

The Impact of Inherent Instructional Design in Online Courseware.

ERIC Educational Resources Information Center

Harvey, Douglas M.; Lee, Jung

2001-01-01

Examines how the use of server-based courseware development solutions affects the instructional design process when creating online distance education. Highlights include pedagogical, visual interface (e.g., visual metaphor and navigation layout), interaction, and instructional design implications of online courseware. (Contains 54 references.)…

A new code for the design and analysis of the heliostat field layout for power tower system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wei, Xiudong; Lu, Zhenwu; Yu, Weixing

2010-04-15

A new code for the design and analysis of the heliostat field layout for power tower system is developed. In the new code, a new method for the heliostat field layout is proposed based on the edge ray principle of nonimaging optics. The heliostat field boundary is constrained by the tower height, the receiver tilt angle and size and the heliostat efficiency factor which is the product of the annual cosine efficiency and the annual atmospheric transmission efficiency. With the new method, the heliostat can be placed with a higher efficiency and a faster response speed of the design andmore » optimization can be obtained. A new module for the analysis of the aspherical heliostat is created in the new code. A new toroidal heliostat field is designed and analyzed by using the new code. Compared with the spherical heliostat, the solar image radius of the field is reduced by about 30% by using the toroidal heliostat if the mirror shape and the tracking are ideal. In addition, to maximize the utilization of land, suitable crops can be considered to be planted under heliostats. To evaluate the feasibility of the crop growth, a method for calculating the annual distribution of sunshine duration on the land surface is developed as well. (author)« less

A quantitative model for designing keyboard layout.

PubMed

Shieh, K K; Lin, C C

1999-02-01

This study analyzed the quantitative relationship between keytapping times and ergonomic principles in typewriting skills. Keytapping times and key-operating characteristics of a female subject typing on the Qwerty and Dvorak keyboards for six weeks each were collected and analyzed. The results showed that characteristics of the typed material and the movements of hands and fingers were significantly related to keytapping times. The most significant factors affecting keytapping times were association frequency between letters, consecutive use of the same hand or finger, and the finger used. A regression equation for relating keytapping times to ergonomic principles was fitted to the data. Finally, a protocol for design of computerized keyboard layout based on the regression equation was proposed.

The layout of a bacterial genome.

PubMed

Képès, François; Jester, Brian C; Lepage, Thibaut; Rafiei, Nafiseh; Rosu, Bianca; Junier, Ivan

2012-07-16

Recently the mismatch between our newly acquired capacity to synthetize DNA at genome scale, and our low capacity to design ab initio a functional genome has become conspicuous. This essay gathers a variety of constraints that globally shape natural genomes, with a focus on eubacteria. These constraints originate from chromosome replication (leading/lagging strand asymmetry; gene dosage gradient from origin to terminus; collisions with the transcription complexes), from biased codon usage, from noise control in gene expression, and from genome layout for co-functional genes. On the basis of this analysis, lessons are drawn for full genome design. Copyright © 2012 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

21 CFR 814.39 - PMA supplements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... sterilization procedures. (5) Changes in packaging. (6) Changes in the performance or design specifications, circuits, components, ingredients, principle of operation, or physical layout of the device. (7) Extension... the performance or design specifications, circuits, components, ingredients, principles of operation...

Longitudinal channelizing devices along business entrances in work zones : [summary].

DOT National Transportation Integrated Search

2015-04-01

The Florida Department of Transportations Design Standards requires placement of business : entrance signs and channelizing devices at business entrances in work zones. The Design : Standards also specifies the layout of the signs and devices. Typ...

Implications of system usability on intermodal facility design.

DOT National Transportation Integrated Search

2010-08-01

Ensuring good design of intermodal transportation facilities is critical for effective and : satisfactory operation. Passenger use of the facilities is often hindered by inadequate space, a poor : layout, or lack of signage. This project aims to impr...

A VLSI implementation of DCT using pass transistor technology

NASA Technical Reports Server (NTRS)

Kamath, S.; Lynn, Douglas; Whitaker, Sterling

1992-01-01

A VLSI design for performing the Discrete Cosine Transform (DCT) operation on image blocks of size 16 x 16 in a real time fashion operating at 34 MHz (worst case) is presented. The process used was Hewlett-Packard's CMOS26--A 3 metal CMOS process with a minimum feature size of 0.75 micron. The design is based on Multiply-Accumulate (MAC) cells which make use of a modified Booth recoding algorithm for performing multiplication. The design of these cells is straight forward, and the layouts are regular with no complex routing. Two versions of these MAC cells were designed and their layouts completed. Both versions were simulated using SPICE to estimate their performance. One version is slightly faster at the cost of larger silicon area and higher power consumption. An improvement in speed of almost 20 percent is achieved after several iterations of simulation and re-sizing.

Hercules Single-Stage Reusable Vehicle (HSRV) Operating Base

NASA Technical Reports Server (NTRS)

Moon, Michael J.; McCleskey, Carey M.

2017-01-01

Conceptual design for the layout of lunar-planetary surface support systems remains an important area needing further master planning. This paper explores a structured approach to organize the layout of a Mars-based site equipped for routinely flying a human-scale reusable taxi system. The proposed Hercules Transportation System requires a surface support capability to sustain its routine, affordable, and dependable operation. The approach organizes a conceptual Hercules operating base through functional station sets. The station set approach will allow follow-on work to trade design approaches and consider technologies for more efficient flow of material, energy, and information at future Mars bases and settlements. The station set requirements at a Mars site point to specific capabilities needed. By drawing from specific Hercules design characteristics, the technology requirements for surface-based systems will come into greater focus. This paper begins a comprehensive process for documenting functional needs, architectural design methods, and analysis techniques necessary for follow-on concept studies.

Human-centered design for neonatal apnea monitoring: application of the UFuRT process to analyze a monitor display layout.

PubMed

Brannon, Timothy S

2008-11-06

Resolution of apnea of prematurity is a criterion for hospital discharge of the preterm infant. False alarms recorded as true events can prolong hospitalization and increase cost of care. The UFuRT process was used to analyze neonatal apnea monitoring, using a typical monitor display. The goals were to determine 1) the data needed to recognize true events and reject false alarms, and 2) how the display layout could be modified to better support these tasks.

An interactive wire-wrap board layout program

NASA Technical Reports Server (NTRS)

Schlutsmeyer, A.

1987-01-01

An interactive computer-graphics-based tool for specifying the placement of electronic parts on a wire-wrap circuit board is presented. Input is a data file (currently produced by a commercial logic design system) which describes the parts used and their interconnections. Output includes printed reports describing the parts and wire paths, parts counts, placement lists, board drawing, and a tape to send to the wire-wrap vendor. The program should reduce the engineer's layout time by a factor of 3 to 5 as compared to manual methods.

Space station functional relationships analysis

NASA Technical Reports Server (NTRS)

Tullis, Thomas S.; Bied, Barbra R.

1988-01-01

A systems engineering process is developed to assist Space Station designers to understand the underlying operational system of the facility so that it can be physically arranged and configured to support crew productivity. The study analyzes the operational system proposed for the Space Station in terms of mission functions, crew activities, and functional relationships in order to develop a quantitative model for evaluation of interior layouts, configuration, and traffic analysis for any Station configuration. Development of the model involved identification of crew functions, required support equipment, criteria of assessing functional relationships, and tools for analyzing functional relationship matrices, as well as analyses of crew transition frequency, sequential dependencies, support equipment requirements, potential for noise interference, need for privacy, and overall compatability of functions. The model can be used for analyzing crew functions for the Initial Operating Capability of the Station and for detecting relationships among these functions. Note: This process (FRA) was used during Phase B design studies to test optional layouts of the Space Station habitat module. The process is now being automated as a computer model for use in layout testing of the Space Station laboratory modules during Phase C.

Assessment of controls layout of Indian tractors.

PubMed

Kumar, Adarsh; Bhaskar, Gaikwad; Singh, J K

2009-01-01

Tractors in low-income countries are used both for farm and non-farm activities. Most of the tractors being manufactured in India are products of collaboration with other countries. The design of tractors manufactured in India has not changed much in the past five decades especially from an ergonomics point of view, because of economic considerations. This paper describes a tractor control layout assessment with respect to the Indian population and compares the location of controls with workspace envelopes and the IS12343 standard for commonly used tractors on Indian farms. Controls like steering, foot clutch, foot brake, foot accelerator are located in areas defined by IS12343 standard in some tractors but these are not placed in the workspace envelopes of the Indian population. This results in a mismatch between the workspace envelope and location of controls as defined by the standard. The controls need a complete change in their layout to be in the workspace envelopes, as this cannot be achieved by providing seat movement in the horizontal and vertical directions in the present tractor design.

Form and performance: body shape and prey-capture success in four drift-feeding minnows

Treesearch

Pedro A. Rincón; Markus Bastir; Gary D. Grossman

2008-01-01

Identifying links between morphology and performance for ecologically relevant tasks will help elucidate the relationships between organismal design and fitness. We conducted a laboratory study to quantify the relationship between variation in body shape and prey-capture success in four drift-feeding minnow species. We offered drifting prey to individual fish in a test...

7 CFR 1468.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... conservation planning; conservation practice survey, layout, design, installation, and certification; training... representatives of FSA, the Cooperative State Research, Education, and Extension Service (CSREES), the...

7 CFR 1468.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... conservation planning; conservation practice survey, layout, design, installation, and certification; training... representatives of FSA, the Cooperative State Research, Education, and Extension Service (CSREES), the...

Does the architectural layout of a NICU affect alarm pressure? A comparative clinical audit of a single-family room and an open bay area NICU using a retrospective study design.

PubMed

Joshi, Rohan; Straaten, Henrica van; Mortel, Heidi van de; Long, Xi; Andriessen, Peter; Pul, Carola van

2018-06-30

To determine differences in alarm pressure between two otherwise comparable neonatal intensive care units (NICUs) differing in architectural layout-one of a single-family room (SFR) design and the other of an open bay area (OBA) design. Retrospective audit of more than 2000 patient days from each NICU cataloguing the differences in the number and duration of alarms for critical and alerting alarms, as well as the interaction of clinicians with the patient monitor. Two level 3 NICUs. A total of more than 150 000 critical and 1.2 million alerting alarms were acquired from the two NICUs. The number of audible alarms and the associated noise pollution varied considerably with the OBA NICU generating 44% more alarms per infant per day even though the SFR NICU generated 2.5 as many critical desaturation alarms per infant per day. Differences in the architectural layout of NICUs and the consequent differences in delays, thresholds and distribution systems for alarms are associated with differences in alarm pressure. © Author(s) (or their employer(s)) 2018. Re-use permitted under CC BY-NC. No commercial re-use. See rights and permissions. Published by BMJ.

How work context affects operating room processes: using data mining and computer simulation to analyze facility and process design.

PubMed

Baumgart, André; Denz, Christof; Bender, Hans-Joachim; Schleppers, Alexander

2009-01-01

The complexity of the operating room (OR) requires that both structural (eg, department layout) and behavioral (eg, staff interactions) patterns of work be considered when developing quality improvement strategies. In our study, we investigated how these contextual factors influence outpatient OR processes and the quality of care delivered. The study setting was a German university-affiliated hospital performing approximately 6000 outpatient surgeries annually. During the 3-year-study period, the hospital significantly changed its outpatient OR facility layout from a decentralized (ie, ORs in adjacent areas of the building) to a centralized (ie, ORs in immediate vicinity of each other) design. To study the impact of the facility change on OR processes, we used a mixed methods approach, including process analysis, process modeling, and social network analysis of staff interactions. The change in facility layout was seen to influence OR processes in ways that could substantially affect patient outcomes. For example, we found a potential for more errors during handovers in the new centralized design due to greater interdependency between tasks and staff. Utilization of the mixed methods approach in our analysis, as compared with that of a single assessment method, enabled a deeper understanding of the OR work context and its influence on outpatient OR processes.

Interactive graphical computer-aided design system

NASA Technical Reports Server (NTRS)

Edge, T. M.

1975-01-01

System is used for design, layout, and modification of large-scale-integrated (LSI) metal-oxide semiconductor (MOS) arrays. System is structured around small computer which provides real-time support for graphics storage display unit with keyboard, slave display unit, hard copy unit, and graphics tablet for designer/computer interface.

Message Design Guidelines For Screen-Based Programs.

ERIC Educational Resources Information Center

Rimar, G. I.

1996-01-01

Effective message design for screen-based computer or video instructional programs requires knowledge from many disciplines. Evaluates current conventions and suggests a new set of guidelines for screen-based designers. Discusses screen layout, highlighting and cueing, text font and style, text positioning, color, and graphical user interfaces for…

Locomotive cab design development. volume III: design application analysis - Interim report

DOT National Transportation Integrated Search

1976-10-01

In Volume II of this service of reports on Locomotive Cab Design Development, changes were recommended in the layout and equipment content of locomotive cabs. This report studies the impact of these changes on the interface of the cab with the rest o...

Identity confirmation of drugs and explosives in ion mobility spectrometry using a secondary drift gas.

PubMed

Kanu, Abu B; Hill, Herbert H

2007-10-15

This work demonstrated the potential of using a secondary drift gas of differing polarizability from the primary drift gas for confirmation of a positive response for drugs or explosives by ion mobility spectrometry (IMS). The gas phase mobilities of response ions for selected drugs and explosives were measured in four drift gases. The drift gases chosen for this study were air, nitrogen, carbon dioxide and nitrous oxide providing a range of polarizability and molecular weights. Four other drift gases (helium, neon, argon and sulfur hexafluoride) were also investigated but design limitations of the commercial instrument prevented their use for this application. When ion mobility was plotted against drift gas polarizability, the resulting slopes were often unique for individual ions, indicating that selectivity factors between any two analytes varied with the choice of drift gas. In some cases, drugs like THC and heroin, which are unresolved in air or nitrogen, were well resolved in carbon dioxide or nitrous oxide.

Enabling Comprehension of Patient Subgroups and Characteristics in Large Bipartite Networks: Implications for Precision Medicine

PubMed Central

Bhavnani, Suresh K.; Chen, Tianlong; Ayyaswamy, Archana; Visweswaran, Shyam; Bellala, Gowtham; Rohit, Divekar; Kevin E., Bassler

2017-01-01

A primary goal of precision medicine is to identify patient subgroups based on their characteristics (e.g., comorbidities or genes) with the goal of designing more targeted interventions. While network visualization methods such as Fruchterman-Reingold have been used to successfully identify such patient subgroups in small to medium sized data sets, they often fail to reveal comprehensible visual patterns in large and dense networks despite having significant clustering. We therefore developed an algorithm called ExplodeLayout, which exploits the existence of significant clusters in bipartite networks to automatically “explode” a traditional network layout with the goal of separating overlapping clusters, while at the same time preserving key network topological properties that are critical for the comprehension of patient subgroups. We demonstrate the utility of ExplodeLayout by visualizing a large dataset extracted from Medicare consisting of readmitted hip-fracture patients and their comorbidities, demonstrate its statistically significant improvement over a traditional layout algorithm, and discuss how the resulting network visualization enabled clinicians to infer mechanisms precipitating hospital readmission in specific patient subgroups. PMID:28815099

Triple/quadruple patterning layout decomposition via linear programming and iterative rounding

NASA Astrophysics Data System (ADS)

Lin, Yibo; Xu, Xiaoqing; Yu, Bei; Baldick, Ross; Pan, David Z.

2017-04-01

As the feature size of the semiconductor technology scales down to 10 nm and beyond, multiple patterning lithography (MPL) has become one of the most practical candidates for lithography, along with other emerging technologies, such as extreme ultraviolet lithography (EUVL), e-beam lithography (EBL), and directed self-assembly. Due to the delay of EUVL and EBL, triple and even quadruple patterning is considered to be used for lower metal and contact layers with tight pitches. In the process of MPL, layout decomposition is the key design stage, where a layout is split into various parts and each part is manufactured through a separate mask. For metal layers, stitching may be allowed to resolve conflicts, whereas it is forbidden for contact and via layers. We focus on the application of layout decomposition where stitching is not allowed, such as for contact and via layers. We propose a linear programming (LP) and iterative rounding solving technique to reduce the number of nonintegers in the LP relaxation problem. Experimental results show that the proposed algorithms can provide high quality decomposition solutions efficiently while introducing as few conflicts as possible.

Criteria for Comparing Children's Web Search Tools.

ERIC Educational Resources Information Center

Kuntz, Jerry

1999-01-01

Presents criteria for evaluating and comparing Web search tools designed for children. Highlights include database size; accountability; categorization; search access methods; help files; spell check; URL searching; links to alternative search services; advertising; privacy policy; and layout and design. (LRW)

Executive system software design and expert system implementation

NASA Technical Reports Server (NTRS)

Allen, Cheryl L.

1992-01-01

The topics are presented in viewgraph form and include: software requirements; design layout of the automated assembly system; menu display for automated composite command; expert system features; complete robot arm state diagram and logic; and expert system benefits.

Should learners reason one step at a time? A randomised trial of two diagnostic scheme designs.

PubMed

Blissett, Sarah; Morrison, Deric; McCarty, David; Sibbald, Matthew

2017-04-01

Making a diagnosis can be difficult for learners as they must integrate multiple clinical variables. Diagnostic schemes can help learners with this complex task. A diagnostic scheme is an algorithm that organises possible diagnoses by assigning signs or symptoms (e.g. systolic murmur) to groups of similar diagnoses (e.g. aortic stenosis and aortic sclerosis) and provides distinguishing features to help discriminate between similar diagnoses (e.g. carotid pulse). The current literature does not identify whether scheme layouts should guide learners to reason one step at a time in a terminally branching scheme or weigh multiple variables simultaneously in a hybrid scheme. We compared diagnostic accuracy, perceptual errors and cognitive load using two scheme layouts for cardiac auscultation. Focused on the task of identifying murmurs on Harvey, a cardiopulmonary simulator, 86 internal medicine residents used two scheme layouts. The terminally branching scheme organised the information into single variable decisions. The hybrid scheme combined single variable decisions with a chart integrating multiple distinguishing features. Using a crossover design, participants completed one set of murmurs (diastolic or systolic) with either the terminally branching or the hybrid scheme. The second set of murmurs was completed with the other scheme. A repeated measures manova was performed to compare diagnostic accuracy, perceptual errors and cognitive load between the scheme layouts. There was a main effect of the scheme layout (Wilks' λ = 0.841, F 3,80 = 5.1, p = 0.003). Use of a terminally branching scheme was associated with increased diagnostic accuracy (65 versus 53%, p = 0.02), fewer perceptual errors (0.61 versus 0.98 errors, p = 0.001) and lower cognitive load (3.1 versus 3.5/7, p = 0.023). The terminally branching scheme was associated with improved diagnostic accuracy, fewer perceptual errors and lower cognitive load, suggesting that terminally branching schemes are effective for improving diagnostic accuracy. These findings can inform the design of schemes and other clinical decision aids. © 2017 John Wiley & Sons Ltd and The Association for the Study of Medical Education.

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2013 CFR

2013-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2012 CFR

2012-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

10 CFR 70.64 - Requirements for new facilities or new processes at existing facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... behavior of items relied on for safety. (b) Facility and system design and facility layout must be based on... existing facilities. (a) Baseline design criteria. Each prospective applicant or licensee shall address the following baseline design criteria in the design of new facilities. Each existing licensee shall address the...

Child Care Center Design & the Potential of Architecture.

ERIC Educational Resources Information Center

Abbott, Carl; Abbott, Cooper

This paper discusses the impact of layout and design of child care centers on the education of young children. It asserts that child care facilities must be designed to support and stimulate children's natural developmental processes, providing both direct and indirect educational opportunities. The paper discusses the stages of the design process…

Generalization of the photo process window and its application to OPC test pattern design

NASA Astrophysics Data System (ADS)

Eisenmann, Hans; Peter, Kai; Strojwas, Andrzej J.

2003-07-01

From the early development phase up to the production phase, test pattern play a key role for microlithography. The requirement for test pattern is to represent the design well and to cover the space of all process conditions, e.g. to investigate the full process window and all other process parameters. This paper shows that the current state-of-the-art test pattern do not address these requirements sufficiently and makes suggestions for a better selection of test pattern. We present a new methodology to analyze an existing layout (e.g. logic library, test pattern or full chip) for critical layout situations which does not need precise process data. We call this method "process space decomposition", because it is aimed at decomposing the process impact to a layout feature into a sum of single independent contributions, the dimensions of the process space. This is a generalization of the classical process window, which examines defocus and exposure dependency of given test pattern, e.g. CD value of dense and isolated lines. In our process space we additionally define the dimensions resist effects, etch effects, mask error and misalignment, which describe the deviation of the printed silicon pattern from its target. We further extend it by the pattern space using a product based layout (library, full chip or synthetic test pattern). The criticality of pattern is defined by their deviation due to aerial image, their sensitivity to the respective dimension or several combinations of these. By exploring the process space for a given design, the method allows to find the most critical patterns independent of specific process parameters. The paper provides examples for different applications of the method: (1) selection of design oriented test pattern for lithography development (2) test pattern reduction in process characterization (3) verification/optimization of printability and performance of post processing procedures (like OPC) (4) creation of a sensitive process monitor.

A Novel Analog Integrated Circuit Design Course Covering Design, Layout, and Resulting Chip Measurement

ERIC Educational Resources Information Center

Lin, Wei-Liang; Cheng, Wang-Chuan; Wu, Chen-Hao; Wu, Hai-Ming; Wu, Chang-Yu; Ho, Kuan-Hsuan; Chan, Chueh-An

2010-01-01

This work describes a novel, first-year graduate-level analog integrated circuit (IC) design course. The course teaches students analog circuit design; an external manufacturer then produces their designs in three different silicon chips. The students, working in pairs, then test these chips to verify their success. All work is completed within…

Radiation Hardness Assurance (RHA) for Space Systems

NASA Technical Reports Server (NTRS)

Poivey, Christian; Buchner, Stephen

2007-01-01

This presentation discusses radiation hardness assurance (RHA) for space systems, providing both the programmatic aspects of RHA and the RHA procedure. RHA consists of all activities undertaken to ensure that the electronics and materials of a space system perform to their design specifications after exposure to the space radiation environment. RHA also pertains to environment definition, part selection, part testing, spacecraft layout, radiation tolerant design, and mission/system/subsystems requirements. RHA procedure consists of establishing mission requirements, defining and evaluating the radiation hazard, selecting and categorizing the appropriate parts, and evaluating circuit response to hazard. The RHA approach is based on risk management and is confined only to parts, it includes spacecraft layout, system/subsystem/circuit design, and system requirements and system operations. RHA should be taken into account in the early phases of a program including the proposal and feasibility analysis phases.

Numerical simulation of multi-directional random wave transformation in a yacht port

NASA Astrophysics Data System (ADS)

Ji, Qiaoling; Dong, Sheng; Zhao, Xizeng; Zhang, Guowei

2012-09-01

This paper extends a prediction model for multi-directional random wave transformation based on an energy balance equation by Mase with the consideration of wave shoaling, refraction, diffraction, reflection and breaking. This numerical model is improved by 1) introducing Wen's frequency spectrum and Mitsuyasu's directional function, which are more suitable to the coastal area of China; 2) considering energy dissipation caused by bottom friction, which ensures more accurate results for large-scale and shallow water areas; 3) taking into account a non-linear dispersion relation. Predictions using the extended wave model are carried out to study the feasibility of constructing the Ai Hua yacht port in Qingdao, China, with a comparison between two port layouts in design. Wave fields inside the port for different incident wave directions, water levels and return periods are simulated, and then two kinds of parameters are calculated to evaluate the wave conditions for the two layouts. Analyses show that Layout I is better than Layout II. Calculation results also show that the harbor will be calm for different wave directions under the design water level. On the contrary, the wave conditions do not wholly meet the requirements of a yacht port for ship berthing under the extreme water level. For safety consideration, the elevation of the breakwater might need to be properly increased to prevent wave overtopping under such water level. The extended numerical simulation model may provide an effective approach to computing wave heights in a harbor.

Effects of Item Parameter Drift on Vertical Scaling with the Nonequivalent Groups with Anchor Test (NEAT) Design

ERIC Educational Resources Information Center

Ye, Meng; Xin, Tao

2014-01-01

The authors explored the effects of drifting common items on vertical scaling within the higher order framework of item parameter drift (IPD). The results showed that if IPD occurred between a pair of test levels, the scaling performance started to deviate from the ideal state, as indicated by bias of scaling. When there were two items drifting…

Design and performance of a straw tube drift chamber

NASA Astrophysics Data System (ADS)

Oh, S. H.; Wesson, D. K.; Cooke, J.; Goshaw, A. T.; Robertson, W. J.; Walker, W. D.

1991-06-01

The design and performance of the straw drift chambers used in E735 is reported. The chambers are constructed from 2.5 cm radius aluminized mylar straw tubes with wall thickness less than 0.2 mm. Also, presented are the results of tests with 2 mm radius straw tubes. The small tube has a direct detector application at the Superconducting Super Collider.

European Design Types for 21st Century Schools: An Overview

ERIC Educational Resources Information Center

Rigolon, Alessandro

2010-01-01

This article presents a critical overview of European school building design types, based on an analysis of morphologies and spatial layouts. The different design types are evaluated in function of specific didactic and social needs. (Contains 1 figure, 18 footnotes, a bibliography and 2 online resources.)

14 CFR 1221.108 - Establishment of the NASA Unified Visual Communications System.

Code of Federal Regulations, 2013 CFR

2013-01-01

... forward-looking image through the use of effective design for improved communications. The system provides a professional and cohesive NASA identity by imparting continuity of graphics design in all layout... developed under the Federal Design Improvement Program initiated by the President in May 1972. This system...

14 CFR 1221.108 - Establishment of the NASA Unified Visual Communications System.

Code of Federal Regulations, 2011 CFR

2011-01-01

... forward-looking image through the use of effective design for improved communications. The system provides a professional and cohesive NASA identity by imparting continuity of graphics design in all layout... developed under the Federal Design Improvement Program initiated by the President in May 1972. This system...

Heat source reentry vehicle design study

NASA Technical Reports Server (NTRS)

Ryan, R. L.

1971-01-01

The design details are presented of a flight-type heat source reentry vehicle and heat exchanger compatible with the isotope Brayton power conversion system. The reference reentry vehicle and heat exchanger were modified, orbital and superorbital capability was assessed, and a complete set of detail design layout drawings were provided.

SCM: A method to improve network service layout efficiency with network evolution

PubMed Central

Zhao, Qi; Zhang, Chuanhao

2017-01-01

Network services are an important component of the Internet, which are used to expand network functions for third-party developers. Network function virtualization (NFV) can improve the speed and flexibility of network service deployment. However, with the evolution of the network, network service layout may become inefficient. Regarding this problem, this paper proposes a service chain migration (SCM) method with the framework of “software defined network + network function virtualization” (SDN+NFV), which migrates service chains to adapt to network evolution and improves the efficiency of the network service layout. SCM is modeled as an integer linear programming problem and resolved via particle swarm optimization. An SCM prototype system is designed based on an SDN controller. Experiments demonstrate that SCM could reduce the network traffic cost and energy consumption efficiently. PMID:29267299

The Engineering Development Array: A Low Frequency Radio Telescope Utilising SKA Precursor Technology

NASA Astrophysics Data System (ADS)

Wayth, Randall; Sokolowski, Marcin; Booler, Tom; Crosse, Brian; Emrich, David; Grootjans, Robert; Hall, Peter J.; Horsley, Luke; Juswardy, Budi; Kenney, David; Steele, Kim; Sutinjo, Adrian; Tingay, Steven J.; Ung, Daniel; Walker, Mia; Williams, Andrew; Beardsley, A.; Franzen, T. M. O.; Johnston-Hollitt, M.; Kaplan, D. L.; Morales, M. F.; Pallot, D.; Trott, C. M.; Wu, C.

2017-08-01

We describe the design and performance of the Engineering Development Array, which is a low-frequency radio telescope comprising 256 dual-polarisation dipole antennas working as a phased array. The Engineering Development Array was conceived of, developed, and deployed in just 18 months via re-use of Square Kilometre Array precursor technology and expertise, specifically from the Murchison Widefield Array radio telescope. Using drift scans and a model for the sky brightness temperature at low frequencies, we have derived the Engineering Development Array's receiver temperature as a function of frequency. The Engineering Development Array is shown to be sky-noise limited over most of the frequency range measured between 60 and 240 MHz. By using the Engineering Development Array in interferometric mode with the Murchison Widefield Array, we used calibrated visibilities to measure the absolute sensitivity of the array. The measured array sensitivity matches very well with a model based on the array layout and measured receiver temperature. The results demonstrate the practicality and feasibility of using Murchison Widefield Array-style precursor technology for Square Kilometre Array-scale stations. The modular architecture of the Engineering Development Array allows upgrades to the array to be rolled out in a staged approach. Future improvements to the Engineering Development Array include replacing the second stage beamformer with a fully digital system, and to transition to using RF-over-fibre for the signal output from first stage beamformers.

48 CFR 19.1005 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... nonpropelled ships west of the 108th meridian. 3. Architectural and Engineering Services (Including Surveying... Architect-Engineering Services (including landscaping, interior layout, and designing). PSC C212 Engineering... Services. PSC C215 A&E Production Engineering Services (including Design and Control, and Building...

An Arsenal Ship Design

DTIC Science & Technology

1996-12-01

151 B. PROPULSION PLANT SELECTION....................................................................... 152 ix C. PROPULSION PLANT LAYOUT...155 D. ELECTRICAL PLANT SELECTION...designed into the hull and power plant and once finalized is only a function of how many miles the ship is to be driven. Decision trade- offs are to

Practical proof of CP element based design for 14nm node and beyond

NASA Astrophysics Data System (ADS)

Maruyama, Takashi; Takita, Hiroshi; Ikeno, Rimon; Osawa, Morimi; Kojima, Yoshinori; Sugatani, Shinji; Hoshino, Hiromi; Hino, Toshio; Ito, Masaru; Iizuka, Tetsuya; Komatsu, Satoshi; Ikeda, Makoto; Asada, Kunihiro

2013-03-01

To realize HVM (High Volume Manufacturing) with CP (Character Projection) based EBDW, the shot count reduction is the essential key. All device circuits should be composed with predefined character parts and we call this methodology "CP element based design". In our previous work, we presented following three concepts [2]. 1) Memory: We reported the prospects of affordability for the CP-stencil resource. 2) Logic cell: We adopted a multi-cell clustering approach in the physical synthesis. 3) Random interconnect: We proposed an ultra-regular layout scheme using fixed size wiring tiles containing repeated tracks and cutting points at the tile edges. In this paper, we will report the experimental proofs in these methodologies. In full chip layout, CP stencil resource management is critical key. From the MCC-POC (Proof of Concept) result [1], we assumed total available CP stencil resource as 9000um2. We should manage to layout all circuit macros within this restriction. Especially the issues in assignment of CP-stencil resource for the memory macros are the most important as they consume considerable degree of resource because of the various line-ups such as 1RW-, 2RW-SRAMs, Resister Files and ROM which require several varieties of large size peripheral circuits. Furthermore the memory macros typically take large area of more than 40% of die area in the forefront logic LSI products so that the shot count increase impact is serious. To realize CP-stencil resource saving we had constructed automatic CP analyzing system. We developed two types of extraction mode of simple division by block and layout repeatability recognition. By properly controlling these models based upon each peripheral circuit characteristics, we could minimize the consumption of CP stencil resources. The estimation for 14nm technology node had been performed based on the analysis of practical memory compiler. The required resource for memory macro is proved to be affordable value which is 60% of full CP stencil resource and wafer level converted shot count is proved to be the level which meets 100WPH throughput. In logic cell design, circuit performance verification result after the cell clustering has been estimated. The cell clustering by the acknowledgment of physical distance proved to owe large penalty mainly in the wiring length. To reduce this design penalty, we proposed CP cell clustering by the acknowledgment of logical distance. For shot-count reduction of random interconnect area design, we proposed a more structural routing architecture which consists of the track exchange and the via position arrangement. Putting these design approaches together, we can design CP stencils to hit the target throughput within the area constraint. From the analysis for other macros such as analog, I/O, and DUMMY, it has proved that we don't need special CP design approach than legacy pattern matching CP extraction. From all these experimental results we get good prospects to the reality of full CP element based layout.

Space syntax in healthcare facilities research: a review.

PubMed

Haq, Saif; Luo, Yang

2012-01-01

Space Syntax is a theory and method that has been developing for the last 40 years. Originally conceived as a theory of "society and space," it has expanded to other areas. An important aspect of this is technical; it allows the quantification of layouts, and unit spaces within a layout, so that the environment itself can produce independent variables in quantitative research. Increasingly, it is being used to study healthcare facilities. Space Syntax has thereby become relevant to healthcare facilities researchers and designers. This paper attempts to explain Space Syntax to a new audience of healthcare designers, administrators, and researchers; it provides a literature review on the use of Space Syntax in healthcare facility research and suggests some possibilities for future application.

Modeling OPC complexity for design for manufacturability

NASA Astrophysics Data System (ADS)

Gupta, Puneet; Kahng, Andrew B.; Muddu, Swamy; Nakagawa, Sam; Park, Chul-Hong

2005-11-01

Increasing design complexity in sub-90nm designs results in increased mask complexity and cost. Resolution enhancement techniques (RET) such as assist feature addition, phase shifting (attenuated PSM) and aggressive optical proximity correction (OPC) help in preserving feature fidelity in silicon but increase mask complexity and cost. Data volume increase with rise in mask complexity is becoming prohibitive for manufacturing. Mask cost is determined by mask write time and mask inspection time, which are directly related to the complexity of features printed on the mask. Aggressive RET increase complexity by adding assist features and by modifying existing features. Passing design intent to OPC has been identified as a solution for reducing mask complexity and cost in several recent works. The goal of design-aware OPC is to relax OPC tolerances of layout features to minimize mask cost, without sacrificing parametric yield. To convey optimal OPC tolerances for manufacturing, design optimization should drive OPC tolerance optimization using models of mask cost for devices and wires. Design optimization should be aware of impact of OPC correction levels on mask cost and performance of the design. This work introduces mask cost characterization (MCC) that quantifies OPC complexity, measured in terms of fracture count of the mask, for different OPC tolerances. MCC with different OPC tolerances is a critical step in linking design and manufacturing. In this paper, we present a MCC methodology that provides models of fracture count of standard cells and wire patterns for use in design optimization. MCC cannot be performed by designers as they do not have access to foundry OPC recipes and RET tools. To build a fracture count model, we perform OPC and fracturing on a limited set of standard cells and wire configurations with all tolerance combinations. Separately, we identify the characteristics of the layout that impact fracture count. Based on the fracture count (FC) data from OPC and mask data preparation runs, we build models of FC as function of OPC tolerances and layout parameters.

Model-based multiple patterning layout decomposition

NASA Astrophysics Data System (ADS)

Guo, Daifeng; Tian, Haitong; Du, Yuelin; Wong, Martin D. F.

2015-10-01

As one of the most promising next generation lithography technologies, multiple patterning lithography (MPL) plays an important role in the attempts to keep in pace with 10 nm technology node and beyond. With feature size keeps shrinking, it has become impossible to print dense layouts within one single exposure. As a result, MPL such as double patterning lithography (DPL) and triple patterning lithography (TPL) has been widely adopted. There is a large volume of literature on DPL/TPL layout decomposition, and the current approach is to formulate the problem as a classical graph-coloring problem: Layout features (polygons) are represented by vertices in a graph G and there is an edge between two vertices if and only if the distance between the two corresponding features are less than a minimum distance threshold value dmin. The problem is to color the vertices of G using k colors (k = 2 for DPL, k = 3 for TPL) such that no two vertices connected by an edge are given the same color. This is a rule-based approach, which impose a geometric distance as a minimum constraint to simply decompose polygons within the distance into different masks. It is not desired in practice because this criteria cannot completely capture the behavior of the optics. For example, it lacks of sufficient information such as the optical source characteristics and the effects between the polygons outside the minimum distance. To remedy the deficiency, a model-based layout decomposition approach to make the decomposition criteria base on simulation results was first introduced at SPIE 2013.1 However, the algorithm1 is based on simplified assumption on the optical simulation model and therefore its usage on real layouts is limited. Recently AMSL2 also proposed a model-based approach to layout decomposition by iteratively simulating the layout, which requires excessive computational resource and may lead to sub-optimal solutions. The approach2 also potentially generates too many stiches. In this paper, we propose a model-based MPL layout decomposition method using a pre-simulated library of frequent layout patterns. Instead of using the graph G in the standard graph-coloring formulation, we build an expanded graph H where each vertex represents a group of adjacent features together with a coloring solution. By utilizing the library and running sophisticated graph algorithms on H, our approach can obtain optimal decomposition results efficiently. Our model-based solution can achieve a practical mask design which significantly improves the lithography quality on the wafer compared to the rule based decomposition.

Mesh-size effects on drift sample composition as determined with a triple net sampler

USGS Publications Warehouse

Slack, K.V.; Tilley, L.J.; Kennelly, S.S.

1991-01-01

Nested nets of three different mesh apertures were used to study mesh-size effects on drift collected in a small mountain stream. The innermost, middle, and outermost nets had, respectively, 425 ??m, 209 ??m and 106 ??m openings, a design that reduced clogging while partitioning collections into three size groups. The open area of mesh in each net, from largest to smallest mesh opening, was 3.7, 5.7 and 8.0 times the area of the net mouth. Volumes of filtered water were determined with a flowmeter. The results are expressed as (1) drift retained by each net, (2) drift that would have been collected by a single net of given mesh size, and (3) the percentage of total drift (the sum of the catches from all three nets) that passed through the 425 ??m and 209 ??m nets. During a two day period in August 1986, Chironomidae larvae were dominant numerically in all 209 ??m and 106 ??m samples and midday 425 ??m samples. Large drifters (Ephemerellidae) occurred only in 425 ??m or 209 ??m nets, but the general pattern was an increase in abundance and number of taxa with decreasing mesh size. Relatively more individuals occurred in the larger mesh nets at night than during the day. The two larger mesh sizes retained 70% of the total sediment/detritus in the drift collections, and this decreased the rate of clogging of the 106 ??m net. If an objective of a sampling program is to compare drift density or drift rate between areas or sampling dates, the same mesh size should be used for all sample collection and processing. The mesh aperture used for drift collection should retain all species and life stages of significance in a study. The nested net design enables an investigator to test the adequacy of drift samples. ?? 1991 Kluwer Academic Publishers.

Designing of deployment sequence for braking and drift systems in atmosphere of Mars and Venus

NASA Astrophysics Data System (ADS)

Vorontsov, Victor

2006-07-01

Analysis of project development and space research using contact method, namely, by means of automatic descent modules and balloons shows that designing formation of entry, descent and landing (EDL) sequence and operation in the atmosphere are of great importance. This process starts at the very beginning of designing, has undergone a lot of iterations and influences processing of normal operation results. Along with designing of descent module systems, including systems of braking in the atmosphere, designing of flight operation sequence and trajectories of motion in the atmosphere is performed. As the entire operation sequence and transfer from one phase to another was correctly chosen, the probability of experiment success on the whole and efficiency of application of various systems vary. By now the most extensive experience of Russian specialists in research of terrestrial planets has been gained with the help of automatic interplanetary stations “Mars”, “Venera”, “Vega” which had descent modules and drifting in the atmosphere balloons. Particular interest and complicity of formation of EDL and drift sequence in the atmosphere of these planets arise from radically different operation conditions, in particular, strongly rarefied atmosphere of the one planet and extremely dense atmosphere of another. Consequently, this determines the choice of braking systems and their parameters and method of EDL consequence formation. At the same time there are general fundamental methods and designed research techniques that allowed taking general technical approach to designing of EDL and drift sequence in the atmosphere.

NOAA Photo Library - Meet the Photographers/Frank Ruopoli

Science.gov Websites

Services Center since 1997. Frank earned a B.F.A. in Graphic Design at the Savannah College of Art and Design in 1993. As a designer, he helps package complex scientific information into useful products for /illustrator, his work includes design and layouts for print publications, exhibits, web pages, and multi-media

Optics Near the Snell Angle in a Water-to-Air Change of Medium

DTIC Science & Technology

2007-01-01

the seawater wedge at the focus of a notional 57.3-mm lens modeled in ZEMAX ® [5]. The boxes are plotted in units of µm, and lens focal length is...lenses had insufficient focal-plane coverage. The ZEMAX spot diagram of this layout is depicted in Fig. 4. It is corrected for the horizon angle...the Fig. 9 ZEMAX layout. It is a two-prism design, but only one prism need be built and carried within the camera, with the forward prism being the

36 CFR 292.13 - Standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... conventional architecture and will utilize colors, nonglare roofing materials, and spacing or layout that harmonizes with forested settings. Except for signs, structures designed primarily for purposes of calling..., harmonizing in design and color with the surroundings and shall not be attached to any tree or shrub...

21 CFR 814.39 - PMA supplements.

Code of Federal Regulations, 2012 CFR

2012-04-01

.... (6) Changes in the performance or design specifications, circuits, components, ingredients, principle of operation, or physical layout of the device. (7) Extension of the expiration date of the device... new indications for use of the device, significant changes in the performance or design specifications...

21 CFR 814.39 - PMA supplements.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... (6) Changes in the performance or design specifications, circuits, components, ingredients, principle of operation, or physical layout of the device. (7) Extension of the expiration date of the device... new indications for use of the device, significant changes in the performance or design specifications...

21 CFR 814.39 - PMA supplements.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... (6) Changes in the performance or design specifications, circuits, components, ingredients, principle of operation, or physical layout of the device. (7) Extension of the expiration date of the device... new indications for use of the device, significant changes in the performance or design specifications...

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2011 CFR

2011-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

36 CFR 292.13 - Standards.

Code of Federal Regulations, 2014 CFR

2014-07-01

... conventional architecture and will utilize colors, nonglare roofing materials, and spacing or layout that harmonizes with forested settings. Except for signs, structures designed primarily for purposes of calling..., harmonizing in design and color with the surroundings and shall not be attached to any tree or shrub...

36 CFR 292.13 - Standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... conventional architecture and will utilize colors, nonglare roofing materials, and spacing or layout that harmonizes with forested settings. Except for signs, structures designed primarily for purposes of calling..., harmonizing in design and color with the surroundings and shall not be attached to any tree or shrub...

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2012 CFR

2012-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

32 CFR Appendix B to Part 223 - Guidelines for the Determination of DoD UCNI

Code of Federal Regulations, 2010 CFR

2010-07-01

... Systems a. Information on the layout or design of security and alarm systems at a specific DoD SNM.... Frequency and schedule of DoD SNM inventories. 3. Facility Description a. Maps, conceptual design, and...

Intelligent Help in the LOCATE Workspace Layout Tool

DTIC Science & Technology

1999-06-01

LOCATE’s basic design and analysis features; • commercialising the application; • expanding the groundwork for tracking actions and goals at the interface...Muraida, D.J. (Eds.) (1993). Automating instructional design: Concepts and issues. Englewood Cliffs, N.J.: Educational Technology Publications

Crossbar H-mode drift-tube linac design with alternative phase focusing for muon linac

NASA Astrophysics Data System (ADS)

Otani, M.; Futatsukawa, K.; Hasegawa, K.; Kitamura, R.; Kondo, Y.; Kurennoy, S.

2017-07-01

We have developed a Crossbar H-mode (CH) drift-tube linac (DTL) design with an alternative phase focusing (APF) scheme for a muon linac, in order to measure the anomalous magnetic moment and electric dipole moment (EDM) of muons at the Japan Proton Accelerator Research Complex (J-PARC). The CH-DTL accelerates muons from β = v/c = 0.08 to 0.28 at an operational frequency of 324 MHz. The design and results are described in this paper.

TRIZ Tool for Optimization of Airport Runway

NASA Astrophysics Data System (ADS)

Rao, K. Venkata; Selladurai, V.; Saravanan, R.

TRIZ tool is used for conceptual design and layout of the novel ascending and descending runway model for the effective utilization of short length airports. Handling bigger aircrafts at smaller airports become the necessity for economic consideration and for the benefit of vast airliners and the aspiring air travelers of the region. The authors’ proposal of ascending and descending runway would enable the operational need of wide body aircrafts such as Boeing 747 and Airbus A380-800. Negotiating take-off and landing of bigger aircrafts at less than 10000 feet runway is an optimization solution. This conceptual model and the theoretical design with its layout is dealt in this paper as Part - I. The computer-aided design and analysis using MATLAB with Simulink tool box to confirm the adequacy of the runway length for the bigger aircrafts at smaller airports is however dealt in subsequent papers.

A Computer Program for Drip Irrigation System Design for Small Plots

NASA Astrophysics Data System (ADS)

Philipova, Nina; Nicheva, Olga; Kazandjiev, Valentin; Chilikova-Lubomirova, Mila

2012-12-01

A computer programhas been developed for design of surface drip irrigation system. It could be applied for calculation of small scale fields with an area up to 10 ha. The program includes two main parts: crop water requirements and hydraulic calculations of the system. It has been developed in Graphical User Interface in MATLAB and gives opportunity for selecting some parameters from tables such as: agro- physical soil properties, characteristics of the corresponding crop, climatic data. It allows the user of the program to assume and set a definite value, for example the emitter discharge, plot parameters and etc. Eight cases of system layout according to the water source layout and the number of plots of the system operation are laid into hydraulic section of the program. It includes the design of lateral, manifold, main line and pump calculations. The program has been compiled to work in Windows.

The role of optimization in the next generation of computer-based design tools

NASA Technical Reports Server (NTRS)

Rogan, J. Edward

1989-01-01

There is a close relationship between design optimization and the emerging new generation of computer-based tools for engineering design. With some notable exceptions, the development of these new tools has not taken full advantage of recent advances in numerical design optimization theory and practice. Recent work in the field of design process architecture has included an assessment of the impact of next-generation computer-based design tools on the design process. These results are summarized, and insights into the role of optimization in a design process based on these next-generation tools are presented. An example problem has been worked out to illustrate the application of this technique. The example problem - layout of an aircraft main landing gear - is one that is simple enough to be solved by many other techniques. Although the mathematical relationships describing the objective function and constraints for the landing gear layout problem can be written explicitly and are quite straightforward, an approximation technique has been used in the solution of this problem that can just as easily be applied to integrate supportability or producibility assessments using theory of measurement techniques into the design decision-making process.

Effect of two layouts on high technology AAC navigation and content location by people with aphasia.

PubMed

Wallace, Sarah E; Hux, Karen

2014-03-01

Navigating high-technology augmentative and alternative communication (AAC) devices with dynamic displays can be challenging for people with aphasia. The purpose of this study was to determine which of two AAC interfaces two people with aphasia could use most efficiently and accurately. The researchers used a BCB'C' alternating treatment design to provide device-use instruction to two people with severe aphasia regarding two personalised AAC interfaces that had different navigation layouts but identical content. One interface had static buttons for homepage and go-back features, and the other interface had static buttons in a navigation ring layout. Throughout treatment, the researchers monitored participants' mastery patterns regarding navigation efficiency and accuracy when locating target messages. Participants' accuracy and efficiency improved with both interfaces given intervention; however, the navigation ring layout appeared more transparent and better facilitated navigation than the homepage layout. People with aphasia can learn to navigate computerised devices; however, interface layout can substantially affect the efficiency and accuracy with which they locate messages. Given intervention incorporating errorless learning principles, people with chronic aphasia can learn to navigate across multiple device levels to locate target sentences. Both navigation ring and homepage interfaces may be used by people with aphasia. Some people with aphasia may be more consistent and efficient in finding target sentences using the navigation ring interface than the homepage interface. Additionally, the navigation ring interface may be more transparent and easier for people with aphasia to master--that is, they may require fewer intervention sessions to learn to navigate the navigation ring interface. Generalisation of learning may result from use of the navigation ring interface. Specifically, people with aphasia may improve navigation with the homepage interface as a result of instruction on the navigation interface, but not vice versa.

ForceAtlas2, a continuous graph layout algorithm for handy network visualization designed for the Gephi software.

PubMed

Jacomy, Mathieu; Venturini, Tommaso; Heymann, Sebastien; Bastian, Mathieu

2014-01-01

Gephi is a network visualization software used in various disciplines (social network analysis, biology, genomics...). One of its key features is the ability to display the spatialization process, aiming at transforming the network into a map, and ForceAtlas2 is its default layout algorithm. The latter is developed by the Gephi team as an all-around solution to Gephi users' typical networks (scale-free, 10 to 10,000 nodes). We present here for the first time its functioning and settings. ForceAtlas2 is a force-directed layout close to other algorithms used for network spatialization. We do not claim a theoretical advance but an attempt to integrate different techniques such as the Barnes Hut simulation, degree-dependent repulsive force, and local and global adaptive temperatures. It is designed for the Gephi user experience (it is a continuous algorithm), and we explain which constraints it implies. The algorithm benefits from much feedback and is developed in order to provide many possibilities through its settings. We lay out its complete functioning for the users who need a precise understanding of its behaviour, from the formulas to graphic illustration of the result. We propose a benchmark for our compromise between performance and quality. We also explain why we integrated its various features and discuss our design choices.

ForceAtlas2, a Continuous Graph Layout Algorithm for Handy Network Visualization Designed for the Gephi Software

PubMed Central

Jacomy, Mathieu; Venturini, Tommaso; Heymann, Sebastien; Bastian, Mathieu

2014-01-01

Gephi is a network visualization software used in various disciplines (social network analysis, biology, genomics…). One of its key features is the ability to display the spatialization process, aiming at transforming the network into a map, and ForceAtlas2 is its default layout algorithm. The latter is developed by the Gephi team as an all-around solution to Gephi users’ typical networks (scale-free, 10 to 10,000 nodes). We present here for the first time its functioning and settings. ForceAtlas2 is a force-directed layout close to other algorithms used for network spatialization. We do not claim a theoretical advance but an attempt to integrate different techniques such as the Barnes Hut simulation, degree-dependent repulsive force, and local and global adaptive temperatures. It is designed for the Gephi user experience (it is a continuous algorithm), and we explain which constraints it implies. The algorithm benefits from much feedback and is developed in order to provide many possibilities through its settings. We lay out its complete functioning for the users who need a precise understanding of its behaviour, from the formulas to graphic illustration of the result. We propose a benchmark for our compromise between performance and quality. We also explain why we integrated its various features and discuss our design choices. PMID:24914678

Spatial layout of letters in nonwords affects visual short-term memory load: evidence from human electrophysiology.

PubMed

Prime, David; Dell'acqua, Roberto; Arguin, Martin; Gosselin, Frédéric; Jolicœur, Pierre

2011-03-01

The sustained posterior contralateral negativity (SPCN) was used to investigate the effect of spatial layout on the maintenance of letters in VSTM. SPCN amplitude was measured for words, nonwords, and scrambled nonwords. We reexamined the effects of spatial layout of letters on SPCN amplitude in a design that equated the mean frequency of use of each position. Scrambled letters that did not form words elicited a larger SPCN than either words or nonwords, indicating lower VSTM load for nonwords presented in a typical horizontal array than the load observed for the same letters presented in spatially scrambled locations. In contrast, prior research has shown that the spatial extent of arrays of simple stimuli did not influence the amplitude of the SPCN. Thus, the present results indicate the existence of encoding and VSTM maintenance mechanisms specific to letter and word processing. Copyright © 2010 Society for Psychophysiological Research.

Typography and layout of technical reports - Survey of current practices

NASA Technical Reports Server (NTRS)

Pinelli, T. E.; Cordle, V. M.; Mccullough, R.

1985-01-01

As part of a review of the NASA Langley Research Center scientific and technical information program, 50 technical reports from industry, research institutions, and government agencies were systematically examined and analyzed to determine current usage and practice in regard to (1) typography, including composition method, type style, type size, and margin treatment; (2) graphic design, including layout and imposition of material on the page; and (3) physical media, including paper, ink, and binding methods. The results indicate that approximately 50 percent of the reports were typeset, 70 percent used Roman (serif) type, 80 percent used 10- or 11-point type for text, 60 percent used a ragged right-hand margin, slightly more than half used paragraph indentation, 75 percent used a single-column layout, 65 percent had one or more figures or tables placed perpendicular to (not aligned with) the text, and perfect binding was the most frequently used binding method.

Analysis of Levene's Test under Design Imbalance.

ERIC Educational Resources Information Center

Keyes, Tim K.; Levy, Martin S.

1997-01-01

H. Levene (1960) proposed a heuristic test for heteroscedasticity in the case of a balanced two-way layout, based on analysis of variance of absolute residuals. Conditions under which design imbalance affects the test's characteristics are identified, and a simple correction involving leverage is proposed. (SLD)

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

40 CFR 264.1 - Purpose, scope and applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... owner/operator must design, construct, operate, and maintain a unit within a 100-year floodplain to... procedures must address proper design, construction, maintenance, and operation of remediation waste..., the location of all records within the facility, and the facility layout. In addition, this person...

Developing a Motivational Strategy.

ERIC Educational Resources Information Center

Janson, Robert

1979-01-01

Describes the use of job enrichment techniques as tools for increased productivity and organizational change. The author's motivational work design model changes not only the job design but also structural elements such as physical layout, workflow, and organizational relationships. Behavior change is more important than job enrichment. (MF)

Desktop Design for ESOL Teachers.

ERIC Educational Resources Information Center

Walker, Susan

The guide for teachers of English as a Second Language offers practical advice on the format and layout of instructional materials they produce using desktop publishing technology. An introductory section discusses important design considerations for producing effective materials. Subsequent sections describe how to: organize ideas; outline the…

SUSTAINABLE YEAR-ROUND FOOD PRODUCTION IN COLD CLIMATES

EPA Science Inventory

The output of the Phase II investigation will include the operating pilot plant system to prove the CEHRF concept; an investor ready prospectus that can be presented to future investors; a detailed engineering design consisting of: layout view, rack design, and structural ana...

Alcoa wind turbines

NASA Technical Reports Server (NTRS)

Ai, D. K.

1979-01-01

An overview of Alcoa's wind energy program is given with emphasis on the the development of a low cost, reliable Darrieus Vertical Axis Wind Turbine System. The design layouts and drawings for fabrication are now complete, while fabrication and installation to utilize the design are expected to begin shortly.

Aircraft wing structural design optimization based on automated finite element modelling and ground structure approach

NASA Astrophysics Data System (ADS)

Yang, Weizhu; Yue, Zhufeng; Li, Lei; Wang, Peiyan

2016-01-01

An optimization procedure combining an automated finite element modelling (AFEM) technique with a ground structure approach (GSA) is proposed for structural layout and sizing design of aircraft wings. The AFEM technique, based on CATIA VBA scripting and PCL programming, is used to generate models automatically considering the arrangement of inner systems. GSA is used for local structural topology optimization. The design procedure is applied to a high-aspect-ratio wing. The arrangement of the integral fuel tank, landing gear and control surfaces is considered. For the landing gear region, a non-conventional initial structural layout is adopted. The positions of components, the number of ribs and local topology in the wing box and landing gear region are optimized to obtain a minimum structural weight. Constraints include tank volume, strength, buckling and aeroelastic parameters. The results show that the combined approach leads to a greater weight saving, i.e. 26.5%, compared with three additional optimizations based on individual design approaches.

Self-assembled three dimensional network designs for soft electronics

PubMed Central

Jang, Kyung-In; Li, Kan; Chung, Ha Uk; Xu, Sheng; Jung, Han Na; Yang, Yiyuan; Kwak, Jean Won; Jung, Han Hee; Song, Juwon; Yang, Ce; Wang, Ao; Liu, Zhuangjian; Lee, Jong Yoon; Kim, Bong Hoon; Kim, Jae-Hwan; Lee, Jungyup; Yu, Yongjoon; Kim, Bum Jun; Jang, Hokyung; Yu, Ki Jun; Kim, Jeonghyun; Lee, Jung Woo; Jeong, Jae-Woong; Song, Young Min; Huang, Yonggang; Zhang, Yihui; Rogers, John A.

2017-01-01

Low modulus, compliant systems of sensors, circuits and radios designed to intimately interface with the soft tissues of the human body are of growing interest, due to their emerging applications in continuous, clinical-quality health monitors and advanced, bioelectronic therapeutics. Although recent research establishes various materials and mechanics concepts for such technologies, all existing approaches involve simple, two-dimensional (2D) layouts in the constituent micro-components and interconnects. Here we introduce concepts in three-dimensional (3D) architectures that bypass important engineering constraints and performance limitations set by traditional, 2D designs. Specifically, open-mesh, 3D interconnect networks of helical microcoils formed by deterministic compressive buckling establish the basis for systems that can offer exceptional low modulus, elastic mechanics, in compact geometries, with active components and sophisticated levels of functionality. Coupled mechanical and electrical design approaches enable layout optimization, assembly processes and encapsulation schemes to yield 3D configurations that satisfy requirements in demanding, complex systems, such as wireless, skin-compatible electronic sensors. PMID:28635956

Self-assembled three dimensional network designs for soft electronics

NASA Astrophysics Data System (ADS)

Jang, Kyung-In; Li, Kan; Chung, Ha Uk; Xu, Sheng; Jung, Han Na; Yang, Yiyuan; Kwak, Jean Won; Jung, Han Hee; Song, Juwon; Yang, Ce; Wang, Ao; Liu, Zhuangjian; Lee, Jong Yoon; Kim, Bong Hoon; Kim, Jae-Hwan; Lee, Jungyup; Yu, Yongjoon; Kim, Bum Jun; Jang, Hokyung; Yu, Ki Jun; Kim, Jeonghyun; Lee, Jung Woo; Jeong, Jae-Woong; Song, Young Min; Huang, Yonggang; Zhang, Yihui; Rogers, John A.

2017-06-01

Low modulus, compliant systems of sensors, circuits and radios designed to intimately interface with the soft tissues of the human body are of growing interest, due to their emerging applications in continuous, clinical-quality health monitors and advanced, bioelectronic therapeutics. Although recent research establishes various materials and mechanics concepts for such technologies, all existing approaches involve simple, two-dimensional (2D) layouts in the constituent micro-components and interconnects. Here we introduce concepts in three-dimensional (3D) architectures that bypass important engineering constraints and performance limitations set by traditional, 2D designs. Specifically, open-mesh, 3D interconnect networks of helical microcoils formed by deterministic compressive buckling establish the basis for systems that can offer exceptional low modulus, elastic mechanics, in compact geometries, with active components and sophisticated levels of functionality. Coupled mechanical and electrical design approaches enable layout optimization, assembly processes and encapsulation schemes to yield 3D configurations that satisfy requirements in demanding, complex systems, such as wireless, skin-compatible electronic sensors.

Triple/quadruple patterning layout decomposition via novel linear programming and iterative rounding

NASA Astrophysics Data System (ADS)

Lin, Yibo; Xu, Xiaoqing; Yu, Bei; Baldick, Ross; Pan, David Z.

2016-03-01

As feature size of the semiconductor technology scales down to 10nm and beyond, multiple patterning lithography (MPL) has become one of the most practical candidates for lithography, along with other emerging technologies such as extreme ultraviolet lithography (EUVL), e-beam lithography (EBL) and directed self assembly (DSA). Due to the delay of EUVL and EBL, triple and even quadruple patterning are considered to be used for lower metal and contact layers with tight pitches. In the process of MPL, layout decomposition is the key design stage, where a layout is split into various parts and each part is manufactured through a separate mask. For metal layers, stitching may be allowed to resolve conflicts, while it is forbidden for contact and via layers. In this paper, we focus on the application of layout decomposition where stitching is not allowed such as for contact and via layers. We propose a linear programming and iterative rounding (LPIR) solving technique to reduce the number of non-integers in the LP relaxation problem. Experimental results show that the proposed algorithms can provide high quality decomposition solutions efficiently while introducing as few conflicts as possible.

TreePlus: interactive exploration of networks with enhanced tree layouts.

PubMed

Lee, Bongshin; Parr, Cynthia S; Plaisant, Catherine; Bederson, Benjamin B; Veksler, Vladislav D; Gray, Wayne D; Kotfila, Christopher

2006-01-01

Despite extensive research, it is still difficult to produce effective interactive layouts for large graphs. Dense layout and occlusion make food webs, ontologies, and social networks difficult to understand and interact with. We propose a new interactive Visual Analytics component called TreePlus that is based on a tree-style layout. TreePlus reveals the missing graph structure with visualization and interaction while maintaining good readability. To support exploration of the local structure of the graph and gathering of information from the extensive reading of labels, we use a guiding metaphor of "Plant a seed and watch it grow." It allows users to start with a node and expand the graph as needed, which complements the classic overview techniques that can be effective at (but often limited to) revealing clusters. We describe our design goals, describe the interface, and report on a controlled user study with 28 participants comparing TreePlus with a traditional graph interface for six tasks. In general, the advantage of TreePlus over the traditional interface increased as the density of the displayed data increased. Participants also reported higher levels of confidence in their answers with TreePlus and most of them preferred TreePlus.

Corps of Engineers Structural Engineering Conference Held in St. Johns County, Florida on 8-12 July 1991. Volume 2

DTIC Science & Technology

1992-12-01

problems. Leadership forums were conducted for chiefs of structural design from each office for both military and civil works areas. (Continued) 14...Photographs ....................................... 7 Maintaining Design Quality in the Corps of Engineers .................... II Expedited Design and...25 Portugues Dam Monolith Layout and Survey Control ...................... 33 Cofferdam Design Problems, Point Marion Lock

Design intent optimization at the beyond 7nm node: the intersection of DTCO and EUVL stochastic mitigation techniques

NASA Astrophysics Data System (ADS)

Crouse, Michael; Liebmann, Lars; Plachecki, Vince; Salama, Mohamed; Chen, Yulu; Saulnier, Nicole; Dunn, Derren; Matthew, Itty; Hsu, Stephen; Gronlund, Keith; Goodwin, Francis

2017-03-01

The initial readiness of EUV patterning was demonstrated in 2016 with IBM Alliance's 7nm device technology. The focus has now shifted to driving the 'effective' k1 factor and enabling the second generation of EUV patterning. Thus, Design Technology Co-optimization (DTCO) has become a critical part of technology enablement as scaling has become more challenging and the industry pushes the limits of EUV lithography. The working partnership between the design teams and the process development teams typically involves an iterative approach to evaluate the manufacturability of proposed designs, subsequent modifications to those designs and finally a design manual for the technology. While this approach has served the industry well for many generations, the challenges at the Beyond 7nm node require a more efficient approach. In this work, we describe the use of "Design Intent" lithographic layout optimization where we remove the iterative component of DTCO and replace it with an optimization that achieves both a "patterning friendly" design and minimizes the well-known EUV stochastic effects. Solved together, this "design intent" approach can more quickly achieve superior lithographic results while still meeting the original device's functional specifications. Specifically, in this work we will demonstrate "design intent" optimization for critical BEOL layers using design tolerance bands to guide the source mask co-optimization. The design tolerance bands can be either supplied as part of the original design or derived from some basic rules. Additionally, the EUV stochastic behavior is mitigated by enhancing the image log slope (ILS) for specific key features as part of the overall optimization. We will show the benefit of the "design intent approach" on both bidirectional and unidirectional 28nm min pitch standard logic layouts and compare the more typical iterative SMO approach. Thus demonstrating the benefit of allowing the design to float within the specified range. Lastly, we discuss how the evolution of this approach could lead to layout optimization based entirely on some minimal set of functional requirements and process constraints.

Paving the way to a full chip gate level double patterning application

NASA Astrophysics Data System (ADS)

Haffner, Henning; Meiring, Jason; Baum, Zachary; Halle, Scott

2007-10-01

Double patterning lithography processes can offer significant yield enhancement for challenging circuit designs. Many decomposition (i.e. the process of dividing the layout design into first and second exposures) techniques are possible, but the focus of this paper is on the use of a secondary "cut" mask to trim away extraneous features left from the first exposure. This approach has the advantage that each exposure only needs to support a subset of critical features (e.g. dense lines with the first exposure, isolated spaces with the second one). The extraneous features ("printing assist features" or PrAFs) are designed to support the process window of critical features much like the role of the subresolution assist features (SRAFs) in conventional processes. However, the printing nature of PrAFs leads to many more design options, and hence a greater process and decomposition parameter exploration space, than are available for SRAFs. A decomposition scheme using PRAFs was developed for a gate level process. A critical driver of the work was to deliver improved across-chip linewidth variation (ACLV) performance versus an optimized single exposure process while providing support for a larger range of critical features. A variety of PRAF techniques were investigated by simulation, with a PrAF scheme similar to standard SRAF rules being chosen as the optimal solution [1]. This paper discusses aspects of the code development for an automated PrAF generation and placement scheme and the subsequent decomposition of a layout into two mask levels. While PrAF placement and decomposition is straightforward for layouts with pitch and orientation restrictions, it becomes rather complex for unrestricted layout styles. Because this higher complexity yields more irregularly shaped PrAFs, mask making becomes another critical driver of the optimum placement and clean-up strategies. Examples are given of how those challenges are met or can be successfully circumvented. During subsequent decomposition of the PrAF-enhanced layout into two independent mask levels, various geometric decomposition parameters have to be considered. As an example, the removal of PrAFs has to be guaranteed by a minimum required overlap of the cut mask opening past any PrAF edge. It is discussed that process assumptions such as CD tolerances and overlay as well as inter-level relationship ground rules need to be considered to successfully optimize the final decomposition scheme. Furthermore, simulation and experimental results regarding not only ACLV but also across-device linewidth variation (ADLV) are analyzed.

Design, fabrication and systems integration of a satellite tracked, free-drifting ocean data buoy

NASA Technical Reports Server (NTRS)

Wallace, J. W.; Cox, J. W.

1976-01-01

Engineering details are presented of a small free-drifting buoy configuration designed for use in the study of continental shelf water circulation patterns in the Chesapeake Bight of the Western North Atlantic Ocean. The buoy incoporated French instrumentation and was interrogated by the French EOLE satellite to provide position and four channels of temperature data. The buoy design included a variable depth drogue and a power supply sufficient for six weeks of continuous operations. Proof tests of the configuration indicated an adequate design and subsequent field experiments verified the proper functioning of the system.

14 CFR 152.111 - Application requirements: Airport development.

Code of Federal Regulations, 2013 CFR

2013-01-01

... sketch or sketches of the airport layout indicating the location for each item of work proposed, using...), providing reasonable assurance that the project will be located, designed, constructed, and operated so as... the proposed development in accordance with the design and construction standards listed in appendix B...

14 CFR 152.111 - Application requirements: Airport development.

Code of Federal Regulations, 2012 CFR

2012-01-01

... sketch or sketches of the airport layout indicating the location for each item of work proposed, using...), providing reasonable assurance that the project will be located, designed, constructed, and operated so as... the proposed development in accordance with the design and construction standards listed in appendix B...

14 CFR 152.111 - Application requirements: Airport development.

Code of Federal Regulations, 2011 CFR

2011-01-01

... sketch or sketches of the airport layout indicating the location for each item of work proposed, using...), providing reasonable assurance that the project will be located, designed, constructed, and operated so as... the proposed development in accordance with the design and construction standards listed in appendix B...

76 FR 28925 - Tribal Veterans Cemetery Grants

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-19

... means the process of site selection, land acquisition, design and planning, earth moving, landscaping... space, or functional layout; and it will not enter into a construction contract for the project or... State or Tribal Organization and the design team to provide a standard for preparation of drawings...

14 CFR 152.111 - Application requirements: Airport development.

Code of Federal Regulations, 2014 CFR

2014-01-01

... sketch or sketches of the airport layout indicating the location for each item of work proposed, using...), providing reasonable assurance that the project will be located, designed, constructed, and operated so as... the proposed development in accordance with the design and construction standards listed in appendix B...

14 CFR 152.111 - Application requirements: Airport development.

Code of Federal Regulations, 2010 CFR

2010-01-01

... sketch or sketches of the airport layout indicating the location for each item of work proposed, using...), providing reasonable assurance that the project will be located, designed, constructed, and operated so as... the proposed development in accordance with the design and construction standards listed in appendix B...

Commercial Art I and Commercial Art II: An Instructional Guide.

ERIC Educational Resources Information Center

Montgomery County Public Schools, Rockville, MD.

A teacher's guide for two sequential one-year commercial art courses for high school students is presented. Commercial Art I contains three units: visual communication, product design, and environmental design. Students study visual communication by analyzing advertising techniques, practicing fundamental drawing and layout techniques, creating…

ERGONOMICS ABSTRACTS 48983-49619.

ERIC Educational Resources Information Center

Ministry of Technology, London (England). Warren Spring Lab.

THE LITERATURE OF ERGONOMICS, OR BIOTECHNOLOGY, IS CLASSIFIED INTO 15 AREAS--METHODS, SYSTEMS OF MEN AND MACHINES, VISUAL AND AUDITORY AND OTHER INPUTS AND PROCESSES, INPUT CHANNELS, BODY MEASUREMENTS, DESIGN OF CONTROLS AND INTEGRATION WITH DISPLAYS, LAYOUT OF PANELS AND CONSOLES, DESIGN OF WORK SPACE, CLOTHING AND PERSONAL EQUIPMENT, SPECIAL…

Thomas Jefferson, Page Design, and Desktop Publishing.

ERIC Educational Resources Information Center

Hartley, James

1991-01-01

Discussion of page design for desktop publishing focuses on the importance of functional issues as opposed to aesthetic issues, and criticizes a previous article that stressed aesthetic issues. Topics discussed include balance, consistency in text structure, and how differences in layout affect the clarity of "The Declaration of…

INSTRUMENTATION AND CONTROLS DIVISION ELECTRICAL DESIGN STANDARDS AND GRAPHICAL SYMBOLS

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1961-11-01

Copies are presented of the American Standards Association graphical symbols for electrical and electronic equipment and systems. Recommendations are given for electrical elementary design layout, device codings, etc., for permanent type installations. Electrical diagrams copied from American Drafting Standards Manual are presented. (M.C.G.)

Toward Optimal Target Placement for Neural Prosthetic Devices

PubMed Central

Cunningham, John P.; Yu, Byron M.; Gilja, Vikash; Ryu, Stephen I.; Shenoy, Krishna V.

2008-01-01

Neural prosthetic systems have been designed to estimate continuous reach trajectories (motor prostheses) and to predict discrete reach targets (communication prostheses). In the latter case, reach targets are typically decoded from neural spiking activity during an instructed delay period before the reach begins. Such systems use targets placed in radially symmetric geometries independent of the tuning properties of the neurons available. Here we seek to automate the target placement process and increase decode accuracy in communication prostheses by selecting target locations based on the neural population at hand. Motor prostheses that incorporate intended target information could also benefit from this consideration. We present an optimal target placement algorithm that approximately maximizes decode accuracy with respect to target locations. In simulated neural spiking data fit from two monkeys, the optimal target placement algorithm yielded statistically significant improvements up to 8 and 9% for two and sixteen targets, respectively. For four and eight targets, gains were more modest, as the target layouts found by the algorithm closely resembled the canonical layouts. We trained a monkey in this paradigm and tested the algorithm with experimental neural data to confirm some of the results found in simulation. In all, the algorithm can serve not only to create new target layouts that outperform canonical layouts, but it can also confirm or help select among multiple canonical layouts. The optimal target placement algorithm developed here is the first algorithm of its kind, and it should both improve decode accuracy and help automate target placement for neural prostheses. PMID:18829845

Tracking chamber made of 15-mm mylar drift tubes

NASA Astrophysics Data System (ADS)

Kozhin, A.; Borisov, A.; Bozhko, N.; Fakhrutdinov, R.; Plotnikov, I.

2017-05-01

We are presenting a drift chamber composed from three layers of mylar drift tubes with outer diameter 15 mm. The pipe is made of strip of mylar film 125 micrometers thick covered with aluminium from the both sides. A strip of mylar is wrapped around the mandrel. Pipe is created by ultrasonic welding. A single drift tube is self-supported structure withstanding 350 g wire tension without supports and internal overpressure. About 400 such tubes were assembled. Design, quality control procedures of the drift tubes are described. Seven chambers were glued from these tubes of 560 mm length. Each chamber consists of 3 layers, 16 tubes per layer. Several chambers were tested with cosmic rays. Results of the tests, counting rate plateau and coordinate resolution are presented.

Drift and Behavior of E. coli Cells

NASA Astrophysics Data System (ADS)

Micali, Gabriele; Colin, Rémy; Sourjik, Victor; Endres, Robert G.

2017-12-01

Chemotaxis of the bacterium Escherichia coli is well understood in shallow chemical gradients, but its swimming behavior remains difficult to interpret in steep gradients. By focusing on single-cell trajectories from simulations, we investigated the dependence of the chemotactic drift velocity on attractant concentration in an exponential gradient. While maxima of the average drift velocity can be interpreted within analytical linear-response theory of chemotaxis in shallow gradients, limits in drift due to steep gradients and finite number of receptor-methylation sites for adaptation go beyond perturbation theory. For instance, we found a surprising pinning of the cells to the concentration in the gradient at which cells run out of methylation sites. To validate the positions of maximal drift, we recorded single-cell trajectories in carefully designed chemical gradients using microfluidics.

Novel Drift Structures for Silicon and Compound Semiconductor X-Ray and Gamma-Ray Detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bradley E. Patt; Jan S. Iwanczyk

Recently developed silicon- and compound-semiconductor-based drift detector structures have produced excellent performance for charged particles, X rays, and gamma rays and for low-signal visible light detection. The silicon drift detector (SDD) structures that we discuss relate to direct X-ray detectors and scintillation photon detectors coupled with scintillators for gamma rays. Recent designs include several novel features that ensure very low dark current (both bulk silicon dark current and surface dark current) and hence low noise. In addition, application of thin window technology ensures a very high quantum efficiency entrance window on the drift photodetector.

Influence of detergents on water drift in cooling towers

NASA Astrophysics Data System (ADS)

Vitkovicova, Rut

An influence of detergents on the water drift from the cooling tower was experimentally investigated. For this experimental measurements was used a model cooling tower, especially an experimental aerodynamic line, which is specially designed for the measurement and monitoring of processes taking place around the eliminators of the liquid phase. The effect of different concentrations of detergent in the cooling water on the drift of water droplets from a commonly used type eliminator was observed with visualization methods.

Look/Learn

ERIC Educational Resources Information Center

Nicoll, William

1976-01-01

The textbook characteristics of type size, type style, and layout, and the important psychological role these play in learning are discussed in terms of their application to the design of a typewriting text. (Editor/HD)

46 CFR 62.20-1 - Plans for approval.

Code of Federal Regulations, 2013 CFR

2013-10-01

... console, panel, and enclosure layouts. (3) Schematic or logic diagrams including functional relationships... features. (6) A description of built-in test features and diagnostics. (7) Design Verification and Periodic...

46 CFR 62.20-1 - Plans for approval.

Code of Federal Regulations, 2011 CFR

2011-10-01

... console, panel, and enclosure layouts. (3) Schematic or logic diagrams including functional relationships... features. (6) A description of built-in test features and diagnostics. (7) Design Verification and Periodic...

46 CFR 62.20-1 - Plans for approval.

Code of Federal Regulations, 2010 CFR

2010-10-01

... console, panel, and enclosure layouts. (3) Schematic or logic diagrams including functional relationships... features. (6) A description of built-in test features and diagnostics. (7) Design Verification and Periodic...

46 CFR 62.20-1 - Plans for approval.

Code of Federal Regulations, 2012 CFR

2012-10-01

... console, panel, and enclosure layouts. (3) Schematic or logic diagrams including functional relationships... features. (6) A description of built-in test features and diagnostics. (7) Design Verification and Periodic...

46 CFR 62.20-1 - Plans for approval.

Code of Federal Regulations, 2014 CFR

2014-10-01

... console, panel, and enclosure layouts. (3) Schematic or logic diagrams including functional relationships... programmable features. (6) A description of built-in test features and diagnostics. (7) Design Verification and...

75 FR 18514 - Developing Guidance on Naming, Labeling, and Packaging Practices to Reduce Medication Errors...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-12

..., layout, use of color, use of graphics, and costs associated with designing labels. Panel 1 will address... from the general public about the design of drug and therapeutic biologic container labels, carton... packaging designs. Among these measures, FDA agreed that by the end of FY 2010, after public consultation...

Investigation of model-based physical design restrictions (Invited Paper)

NASA Astrophysics Data System (ADS)

Lucas, Kevin; Baron, Stanislas; Belledent, Jerome; Boone, Robert; Borjon, Amandine; Couderc, Christophe; Patterson, Kyle; Riviere-Cazaux, Lionel; Rody, Yves; Sundermann, Frank; Toublan, Olivier; Trouiller, Yorick; Urbani, Jean-Christophe; Wimmer, Karl

2005-05-01

As lithography and other patterning processes become more complex and more non-linear with each generation, the task of physical design rules necessarily increases in complexity also. The goal of the physical design rules is to define the boundary between the physical layout structures which will yield well from those which will not. This is essentially a rule-based pre-silicon guarantee of layout correctness. However the rapid increase in design rule requirement complexity has created logistical problems for both the design and process functions. Therefore, similar to the semiconductor industry's transition from rule-based to model-based optical proximity correction (OPC) due to increased patterning complexity, opportunities for improving physical design restrictions by implementing model-based physical design methods are evident. In this paper we analyze the possible need and applications for model-based physical design restrictions (MBPDR). We first analyze the traditional design rule evolution, development and usage methodologies for semiconductor manufacturers. Next we discuss examples of specific design rule challenges requiring new solution methods in the patterning regime of low K1 lithography and highly complex RET. We then evaluate possible working strategies for MBPDR in the process development and product design flows, including examples of recent model-based pre-silicon verification techniques. Finally we summarize with a proposed flow and key considerations for MBPDR implementation.

The GlueX central drift chamber: Design and performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Haarlem, Y; Barbosa, F; Dey, B

2010-10-01

Tests and studies concerning the design and performance of the GlueX Central Drift Chamber (CDC) are presented. A full-scale prototype was built to test and steer the mechanical and electronic design. Small scale prototypes were constructed to test for sagging and to do timing and resolution studies of the detector. These studies were used to choose the gas mixture and to program a Monte Carlo simulation that can predict the detector response in an external magnetic field. Particle identification and charge division possibilities were also investigated.

Saving Material with Systematic Process Designs

NASA Astrophysics Data System (ADS)

Kerausch, M.

2011-08-01

Global competition is forcing the stamping industry to further increase quality, to shorten time-to-market and to reduce total cost. Continuous balancing between these classical time-cost-quality targets throughout the product development cycle is required to ensure future economical success. In today's industrial practice, die layout standards are typically assumed to implicitly ensure the balancing of company specific time-cost-quality targets. Although die layout standards are a very successful approach, there are two methodical disadvantages. First, the capabilities for tool design have to be continuously adapted to technological innovations; e.g. to take advantage of the full forming capability of new materials. Secondly, the great variety of die design aspects have to be reduced to a generic rule or guideline; e.g. binder shape, draw-in conditions or the use of drawbeads. Therefore, it is important to not overlook cost or quality opportunities when applying die design standards. This paper describes a systematic workflow with focus on minimizing material consumption. The starting point of the investigation is a full process plan for a typical structural part. All requirements are definedaccording to a predefined set of die design standards with industrial relevance are fulfilled. In a first step binder and addendum geometry is systematically checked for material saving potentials. In a second step, blank shape and draw-in are adjusted to meet thinning, wrinkling and springback targets for a minimum blank solution. Finally the identified die layout is validated with respect to production robustness versus splits, wrinkles and springback. For all three steps the applied methodology is based on finite element simulation combined with a stochastical variation of input variables. With the proposed workflow a well-balanced (time-cost-quality) production process assuring minimal material consumption can be achieved.

Optimized micromirror arrays for adaptive optics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michalicek, M. Adrian

This paper describes the design, layout, fabrication, and surface characterization of highly optimized surface micromachined micromirror devices. Design considerations and fabrication capabilities are presented. These devices are fabricated in the state-of-the-art, four-level, planarized, ultra-low-stress polysilicon process available at Sandia National Laboratories known as the Sandia Ultra-planar Multi-level MEMS Technology (SUMMiT). This enabling process permits the development of micromirror devices with near-ideal characteristics that have previously been unrealizable in standard three-layer polysilicon processes. The reduced 1 {mu}m minimum feature sizes and 0.1 {mu}m mask resolution make it possible to produce dense wiring patterns and irregularly shaped flexures. Likewise, mirror surfaces canmore » be uniquely distributed and segmented in advanced patterns and often irregular shapes in order to minimize wavefront error across the pupil. The ultra-low-stress polysilicon and planarized upper layer allow designers to make larger and more complex micromirrors of varying shape and surface area within an array while maintaining uniform performance of optical surfaces. Powerful layout functions of the AutoCAD editor simplify the design of advanced micromirror arrays and make it possible to optimize devices according to the capabilities of the fabrication process. Micromirrors fabricated in this process have demonstrated a surface variance across the array from only 2{endash}3 nm to a worst case of roughly 25 nm while boasting active surface areas of 98{percent} or better. Combining the process planarization with a {open_quotes}planarized-by-design{close_quotes} approach will produce micromirror array surfaces that are limited in flatness only by the surface deposition roughness of the structural material. Ultimately, the combination of advanced process and layout capabilities have permitted the fabrication of highly optimized micromirror arrays for adaptive optics. {copyright} {ital 1999 American Institute of Physics.}« less

Visualization tool for human-machine interface designers

NASA Astrophysics Data System (ADS)

Prevost, Michael P.; Banda, Carolyn P.

1991-06-01

As modern human-machine systems continue to grow in capabilities and complexity, system operators are faced with integrating and managing increased quantities of information. Since many information components are highly related to each other, optimizing the spatial and temporal aspects of presenting information to the operator has become a formidable task for the human-machine interface (HMI) designer. The authors describe a tool in an early stage of development, the Information Source Layout Editor (ISLE). This tool is to be used for information presentation design and analysis; it uses human factors guidelines to assist the HMI designer in the spatial layout of the information required by machine operators to perform their tasks effectively. These human factors guidelines address such areas as the functional and physical relatedness of information sources. By representing these relationships with metaphors such as spring tension, attractors, and repellers, the tool can help designers visualize the complex constraint space and interacting effects of moving displays to various alternate locations. The tool contains techniques for visualizing the relative 'goodness' of a configuration, as well as mechanisms such as optimization vectors to provide guidance toward a more optimal design. Also available is a rule-based design checker to determine compliance with selected human factors guidelines.

Simulation System of Car Crash Test in C-NCAP Analysis Based on an Improved Apriori Algorithm*

NASA Astrophysics Data System (ADS)

Xiang, LI

In order to analysis car crash test in C-NCAP, an improved algorithm is given based on Apriori algorithm in this paper. The new algorithm is implemented with vertical data layout, breadth first searching, and intersecting. It takes advantage of the efficiency of vertical data layout and intersecting, and prunes candidate frequent item sets like Apriori. Finally, the new algorithm is applied in simulation of car crash test analysis system. The result shows that the relations will affect the C-NCAP test results, and it can provide a reference for the automotive design.

Objectives and Layout of a High-Resolution X-ray Imaging Crystal Spectrometer for the Large Helical Device (LHD)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bitter, M; Gates, D; Monticello, D

A high-resolution X-ray imaging crystal spectrometer, whose concept was tested on NSTX and Alcator C-Mod, is being designed for LHD. This instrument will record spatially resolved spectra of helium-like Ar16+ and provide ion temperature profiles with spatial and temporal resolutions of < 2 cm and ≥ 10 ms. The stellarator equilibrium reconstruction codes, STELLOPT and PIES, will be used for the tomographic inversion of the spectral data. The spectrometer layout and instrumental features are largely determined by the magnetic field structure of LHD.

A temperature characteristic research and compensation design for micro-machined gyroscope

NASA Astrophysics Data System (ADS)

Fu, Qiang; di, Xin-Peng; Chen, Wei-Ping; Yin, Liang; Liu, Xiao-Wei

2017-02-01

The all temperature range stability is the most important technology of MEMS angular velocity sensor according to the principle of capacity detecting. The correlation between driven force and zero-point of sensor is summarized according to the temperature characteristic of the air-damping and resonant frequency of sensor header. A constant trans-conductance high-linearity amplifier is designed to realize the low phase-drift and low amplitude-drift interface circuit at all-temperature range. The chip is fabricated in a standard 0.5 μm CMOS process. Compensation achieved by driven force to zero-point drift caused by the stiffness of physical construction and air-damping is adopted. Moreover, the driven force can be obtained from the drive-circuit to avoid the complex sampling. The test result shows that the zero-point drift is lower than 30∘/h (1-sigma) at the temperature range from -40∘C to 60∘C after three-order compensation made by driven force.

The Elimination of Transfer Distances Is an Important Part of Hospital Design.

PubMed

Karvonen, Sauli; Nordback, Isto; Elo, Jussi; Havulinna, Jouni; Laine, Heikki-Jussi

2017-04-01

The objective of the present study was to describe how a specific patient flow analysis with from-to charts can be used in hospital design and layout planning. As part of a large renewal project at a university hospital, a detailed patient flow analysis was applied to planning the musculoskeletal surgery unit (orthopedics and traumatology, hand surgery, and plastic surgery). First, the main activities of the unit were determined. Next, the routes of all patients treated over the course of 1 year were studied, and their physical movements in the current hospital were calculated. An ideal layout of the new hospital was then generated to minimize transfer distances by placing the main activities with close to each other, according to the patient flow analysis. The actual architectural design was based on the ideal layout plan. Finally, we compared the current transfer distances to the distances patients will move in the new hospital. The methods enabled us to estimate an approximate 50% reduction in transfer distances for inpatients (from 3,100 km/year to 1,600 km/year) and 30% reduction for outpatients (from 2,100 km/year to 1,400 km/year). Patient transfers are nonvalue-added activities. This study demonstrates that a detailed patient flow analysis with from-to charts can substantially shorten transfer distances, thereby minimizing extraneous patient and personnel movements. This reduction supports productivity improvement, cross-professional teamwork, and patient safety by placing all patient flow activities close to each other. Thus, this method is a valuable additional tool in hospital design.

Design of an efficient space constrained diffuser for supercritical CO2 turbines

NASA Astrophysics Data System (ADS)

Keep, Joshua A.; Head, Adam J.; Jahn, Ingo H.

2017-03-01

Radial inflow turbines are an arguably relevant architecture for energy extraction from ORC and supercritical CO 2 power cycles. At small scale, design constraints can prescribe high exit velocities for such turbines, which lead to high kinetic energy in the turbine exhaust stream. The inclusion of a suitable diffuser in a radial turbine system allows some exhaust kinetic energy to be recovered as static pressure, thereby ensuring efficient operation of the overall turbine system. In supercritical CO 2 Brayton cycles, the high turbine inlet pressure can lead to a sealing challenge if the rotor is supported from the rotor rear side, due to the seal operating at rotor inlet pressure. An alternative to this is a cantilevered layout with the rotor exit facing the bearing system. While such a layout is attractive for the sealing system, it limits the axial space claim of any diffuser. Previous studies into conical diffuser geometries for supercritical CO 2 have shown that in order to achieve optimal static pressure recovery, longer geometries of a shallower cone angle are necessitated when compared to air. A diffuser with a combined annular-radial arrangement is investigated as a means to package the aforementioned geometric characteristics into a limited space claim for a 100kW radial inflow turbine. Simulation results show that a diffuser of this design can attain static pressure rise coefficients greater than 0.88. This confirms that annular-radial diffusers are a viable design solution for supercritical CO2 radial inflow turbines, thus enabling an alternative cantilevered rotor layout.

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

39 CFR 310.1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... design of which make them valuable or useful for purposes other than as media for long-distance..., signs or posters the type-size, layout or physical characteristics of which indicate they are primarily...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2013 CFR

2013-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

39 CFR 310.1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... design of which make them valuable or useful for purposes other than as media for long-distance..., signs or posters the type-size, layout or physical characteristics of which indicate they are primarily...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

Research Possibilities Beyond Deep Space Gateway

NASA Astrophysics Data System (ADS)

Smitherman, D. V.; Needham, D. H.; Lewis, R.

2018-02-01

This abstract explores the possibilities for a large research facilities module attached to the Deep Space Gateway, using the same large module design and basic layout planned for the Deep Space Transport.

48 CFR 552.270-14 - Changes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... following: (1) Specifications (including drawings and designs). (2) Work or services. (3) Facilities or space layout. (4) Amount of space, provided the Lessor consents to the change. (b) If any such change...

39 CFR 310.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... design of which make them valuable or useful for purposes other than as media for long-distance..., signs or posters the type-size, layout or physical characteristics of which indicate they are primarily...

39 CFR 310.1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... design of which make them valuable or useful for purposes other than as media for long-distance..., signs or posters the type-size, layout or physical characteristics of which indicate they are primarily...

32 CFR 644.23 - Real Estate Planning Documents.

Code of Federal Regulations, 2013 CFR

2013-07-01

... a Real Estate Design Memorandum). Certain items contained in Figure 2-1 (ER 405-1-12) relate only to.... (vii) A preliminary site plan, showing existing conditions and proposed layout, to insure adequacy of... fee and/or easement real estate design memorandum and review and approval by the District Engineer and...

32 CFR 644.23 - Real Estate Planning Documents.

Code of Federal Regulations, 2012 CFR

2012-07-01

... a Real Estate Design Memorandum). Certain items contained in Figure 2-1 (ER 405-1-12) relate only to.... (vii) A preliminary site plan, showing existing conditions and proposed layout, to insure adequacy of... fee and/or easement real estate design memorandum and review and approval by the District Engineer and...

40 CFR 35.2040 - Grant application.

Code of Federal Regulations, 2010 CFR

2010-07-01

...: (a) Step 2+3: Combined design and building of a treatment works and building related services and... limitations on award (§§ 35.2100 through 35.2127); (5) Final design drawings and specifications; (6) The..., a preliminary layout of the distribution and drainage systems, and an explanation of the intended...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2012 CFR

2012-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″×10″) of the equipment of sufficient clarity to reveal equipment construction and layout...

41 CFR 102-85.80 - Who is financially responsible for expenses resulting from tenant non-performance?

Code of Federal Regulations, 2011 CFR

2011-01-01

... OA. Customer agencies are also financially responsible for revised design costs and any additional costs resulting from changes to space requirements or space layouts made by the agency after a lease, alteration, design, or construction contract has been awarded by GSA. ...

16 CFR 1500.121 - Labeling requirements; prominence, placement, and conspicuousness.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., layout, or color with other printed matter on the label. This regulation contains the Commission's..., which bear(s) the labeling designed to be most prominently displayed, shown, presented, or examined... designed to be displayed for sale or, on display panels other than the principal display panel, in lines...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

41 CFR 102-85.80 - Who is financially responsible for expenses resulting from tenant non-performance?

Code of Federal Regulations, 2012 CFR

2012-01-01

... OA. Customer agencies are also financially responsible for revised design costs and any additional costs resulting from changes to space requirements or space layouts made by the agency after a lease, alteration, design, or construction contract has been awarded by GSA. ...

33 CFR 127.1101 - Piping systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Waterfront Facilities Handling Liquefied Hazardous Gas Design and Construction § 127.1101 Piping systems... following criteria: (a) Each system must be designed and constructed in accordance with ASME B31.3. (b) Each... the line or equipment. Unless the layout of the piping allows the isolation valve at the transfer...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2010 CFR

2010-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″×10″) of the equipment of sufficient clarity to reveal equipment construction and layout...