Concrete Masonry Designs: Educational Issue.

ERIC Educational Resources Information Center

Hertzberg, Randi, Ed.

2001-01-01

This special journal issue addresses concrete masonry in educational facilities construction. The issue's feature articles are: (1) "It Takes a Village To Construct a Massachusetts Middle School," describing a middle school constructed almost entirely of concrete masonry and modeled after a typical small New England village; (2)…

10 CFR 63.32 - Conditions of construction authorization.

Code of Federal Regulations, 2010 CFR

2010-01-01

... during construction, that are not within the predicted limits on which the facility design was based; (3... three categories of descending importance to public health and safety, as follows: (1) Those features...

Best practices for quality management of stormwater pipe construction.

DOT National Transportation Integrated Search

2014-02-01

Stormwater pipe systems are integral features of transportation construction projects. Pipe culverts : direct stormwater away from roadway structures and towards designated discharge areas. The improper : installation of a pipe culvert can result in ...

76 FR 22117 - Notice of Submission of Proposed Information Collection to OMB Manufactured Home Construction and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-20

... Proposed Information Collection to OMB Manufactured Home Construction and Safety Standards Act Reporting... home producers to place labels and notices in and on manufactured homes and mandate State and Private...' interests by requiring certain features of design and construction. In addition, information collected...

Designing attractive gamification features for collaborative storytelling websites.

PubMed

Hsu, Shang Hwa; Chang, Jen-Wei; Lee, Chun-Chia

2013-06-01

Gamification design is considered as the predictor of collaborative storytelling websites' success. Although aforementioned studies have mentioned a broad range of factors that may influence gamification, they neither depicted the actual design features nor relative attractiveness among them. This study aims to identify attractive gamification features for collaborative storytelling websites. We first constructed a hierarchical system structure of gamification design of collaborative storytelling websites and conducted a focus group interview with eighteen frequent users to identify 35gamification features. After that, this study determined the relative attractiveness of these gamification features by administrating an online survey to 6333 collaborative storytelling websites users. The results indicated that the top 10 most attractive gamification features could account for more than 50% of attractiveness among these 35 gamification features. The feature of unpredictable time pressure is important to website users, yet not revealed in previous relevant studies. Implications of the findings were discussed.

Online Patient Education for Chronic Disease Management: Consumer Perspectives.

PubMed

Win, Khin Than; Hassan, Naffisah Mohd; Oinas-Kukkonen, Harri; Probst, Yasmine

2016-04-01

Patient education plays an important role in chronic disease management. The aim of this study is to identify patients' preferences in regard to the design features of effective online patient education (OPE) and the benefits. A review of the existing literature was conducted in order to identify the benefits of OPE and its essential design features. These design features were empirically tested by conducting survey with patients and caregivers. Reliability analysis, construct validity and regression analysis were performed for data analysis. The results identified patient-tailored information, interactivity, content credibility, clear presentation of content, use of multimedia and interpretability as the essential design features of online patient education websites for chronic disease management.

Design and Construction of an Entity Resolution System that Supports Entity Identity Information Management and Asserted Resolution

ERIC Educational Resources Information Center

Nelson, Eric Derrand

2011-01-01

This work describes the design and construction of an open source, entity resolution system that enables users to assign and maintain persistent identifiers for master data items. Two key features of this system that are not available in current ER systems and that make persistent identification possible are (1) The capture and management of…

GATOR: Requirements capturing of telephony features

NASA Technical Reports Server (NTRS)

Dankel, Douglas D., II; Walker, Wayne; Schmalz, Mark

1992-01-01

We are developing a natural language-based, requirements gathering system called GATOR (for the GATherer Of Requirements). GATOR assists in the development of more accurate and complete specifications of new telephony features. GATOR interacts with a feature designer who describes a new feature, set of features, or capability to be implemented. The system aids this individual in the specification process by asking for clarifications when potential ambiguities are present, by identifying potential conflicts with other existing features, and by presenting its understanding of the feature to the designer. Through user interaction with a model of the existing telephony feature set, GATOR constructs a formal representation of the new, 'to be implemented' feature. Ultimately GATOR will produce a requirements document and will maintain an internal representation of this feature to aid in future design and specification. This paper consists of three sections that describe (1) the structure of GATOR, (2) POND, GATOR's internal knowledge representation language, and (3) current research issues.

Conceptual design of a mobile remote manipulator system

NASA Technical Reports Server (NTRS)

Bush, H. G.; Mikulas, M. M., Jr.; Wallsom, R. E.; Jensen, J. K.

1984-01-01

A mobile remote manipulator system has been identified as a necessary device for space station. A conceptual design for an MRMS is presented which features (1) tracks on the MRMS and guide pins only on the truss structure, (2) a push/pull drive mechanism which rotates to permit movement in four directions, and (3) spacecrane and mobile foot restraint manipulators (or arms). Operational and design features of the MRMS elements are described and illustrated. Concepts are also presented which permit rotating the operational plane of the MRMS through 90 deg. Such a system has been found to have great utility for initial space station construction, maintenance and repair, and to provide a construction capability for future station growth or large spacecraft assembly and/or servicing.

Towards the design of 3D multiscale instructive tissue engineering constructs: Current approaches and trends.

PubMed

Oliveira, Sara M; Reis, Rui L; Mano, João F

2015-11-01

The design of 3D constructs with adequate properties to instruct and guide cells both in vitro and in vivo is one of the major focuses of tissue engineering. Successful tissue regeneration depends on the favorable crosstalk between the supporting structure, the cells and the host tissue so that a balanced matrix production and degradation are achieved. Herein, the major occurring events and players in normal and regenerative tissue are overviewed. These have been inspiring the selection or synthesis of instructive cues to include into the 3D constructs. We further highlight the importance of a multiscale perception of the range of features that can be included on the biomimetic structures. Lastly, we focus on the current and developing tissue-engineering approaches for the preparation of such 3D constructs: top-down, bottom-up and integrative. Bottom-up and integrative approaches present a higher potential for the design of tissue engineering devices with multiscale features and higher biochemical control than top-down strategies, and are the main focus of this review. Copyright © 2015 Elsevier Inc. All rights reserved.

14 CFR 27.601 - Design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design. 27.601 Section 27.601 Aeronautics... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.601 Design. (a) The rotorcraft may have no design features or details that experience has shown to be hazardous or unreliable. (b...

14 CFR 27.601 - Design.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design. 27.601 Section 27.601 Aeronautics... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.601 Design. (a) The rotorcraft may have no design features or details that experience has shown to be hazardous or unreliable. (b...

14 CFR 29.601 - Design.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design. 29.601 Section 29.601 Aeronautics... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.601 Design. (a) The rotorcraft may have no design features or details that experience has shown to be hazardous or unreliable. (b...

14 CFR 29.601 - Design.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design. 29.601 Section 29.601 Aeronautics... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.601 Design. (a) The rotorcraft may have no design features or details that experience has shown to be hazardous or unreliable. (b...

Sustainability Base Construction Update

NASA Technical Reports Server (NTRS)

Mewhinney, Michael

2012-01-01

Construction of the new Sustainability Base Collaborative support facility, expected to become the highest performing building in the federal government continues at NASA's Ames Research Center, Moffet Field, Calif. The new building is designed to achieve a platinum rating under the leadership in Energy and Environment Design (LEED) new construction standards for environmentally sustainable construction developed by the U. S. Green Building Council, Washington, D. C. When completed by the end of 2011, the $20.6 million building will feature near zero net energy consumption, use 90 percent less potable water than conventionally build buildings of equivalent size, and will result in reduced building maintenance costs.

Work plan for special design features and crack sealing maintenance.

DOT National Transportation Integrated Search

2013-09-01

The Alaska DOT&PF wants to construct and maintain asphalt concrete (AC) paved highways in a way that minimizes roadway lifecycle costs while preserving acceptable : performance. Thermal cracking is a natural feature of most paved Alaska roadways that...

21 CFR 225.20 - Buildings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CURRENT GOOD MANUFACTURING PRACTICE FOR MEDICATED FEEDS Construction and Maintenance of Facilities and Equipment § 225.20 Buildings. (a) The location, design, construction, and physical size of the buildings and other production facilities are factors important to the manufacture of medicated feed. The features of...

The Universal Design for Play Tool: Establishing Validity and Reliability

ERIC Educational Resources Information Center

Ruffino, Amy Goetz; Mistrett, Susan G.; Tomita, Machiko; Hajare, Poonam

2006-01-01

The Universal Design for Play (UDP) Tool is an instrument designed to evaluate the presence of universal design (UD) features in toys. This study evaluated its psychometric properties, including content validity, construct validity, and test-retest reliability. The UDP tool was designed to assist in selecting toys most appropriate for children…

Preparation and Use of an Easily Constructed, Inexpensive Chamber for Viewing Courtship Behaviors of Fruit Flies, Drosophila sp.

ERIC Educational Resources Information Center

Christensen, Timothy J.; Labov, Jay B.

1997-01-01

Details the construction of a viewing chamber for fruit flies that connects to a dissecting microscope and features a design that enables students to easily move fruit flies in and out of the chamber. (DDR)

Robotic influence in the conceptual design of mechanical systems in space and vice versa - A survey

NASA Technical Reports Server (NTRS)

Sanger, George F.

1988-01-01

A survey of methods using robotic devices to construct structural elements in space is presented. Two approaches to robotic construction are considered: one in which the structural elements are designed using conventional aerospace techniques which tend to constrain the function aspects of robotics and one in which the structural elements are designed from the conceptual stage with built-in robotic features. Examples are presented of structural building concepts using robotics, including the construction of the SP-100 nuclear reactor power system, a multimirror large aperture IR space telescope concept, retrieval and repair in space, and the Flight Telerobotic Servicer.

Perspectives of construction robots

NASA Astrophysics Data System (ADS)

Stepanov, M. A.; Gridchin, A. M.

2018-03-01

This article is an overview of construction robots features, based on formulating the list of requirements for different types of construction robots in relation to different types of construction works.. It describes a variety of construction works and ways to construct new or to adapt existing robot designs for a construction process. Also, it shows the prospects of AI-controlled machines, implementation of automated control systems and networks on construction sites. In the end, different ways to develop and improve, including ecological aspect, the construction process through the wide robotization, creating of data communication networks and, in perspective, establishing of fully AI-controlled construction complex are formulated.

Nuclear Reactor Safety--The APS Submits its Report

ERIC Educational Resources Information Center

Physics Today, 1975

1975-01-01

Presents the summary section of the American Physical Society (APS) report on the safety features of the light-water reactor, reviews the design, construction, and operation of a reactor and outlines the primary engineered safety features. Summarizes the major recommendations of the study group. (GS)

Planning Marine Reserve Networks for Both Feature Representation and Demographic Persistence Using Connectivity Patterns

PubMed Central

Bode, Michael; Williamson, David H.; Weeks, Rebecca; Jones, Geoff P.; Almany, Glenn R.; Harrison, Hugo B.; Hopf, Jess K.; Pressey, Robert L.

2016-01-01

Marine reserve networks must ensure the representation of important conservation features, and also guarantee the persistence of key populations. For many species, designing reserve networks is complicated by the absence or limited availability of spatial and life-history data. This is particularly true for data on larval dispersal, which has only recently become available. However, systematic conservation planning methods currently incorporate demographic processes through unsatisfactory surrogates. There are therefore two key challenges to designing marine reserve networks that achieve feature representation and demographic persistence constraints. First, constructing a method that efficiently incorporates persistence as well as complementary feature representation. Second, incorporating persistence using a mechanistic description of population viability, rather than a proxy such as size or distance. Here we construct a novel systematic conservation planning method that addresses both challenges, and parameterise it to design a hypothetical marine reserve network for fringing coral reefs in the Keppel Islands, Great Barrier Reef, Australia. For this application, we describe how demographic persistence goals can be constructed for an important reef fish species in the region, the bar-cheeked trout (Plectropomus maculatus). We compare reserve networks that are optimally designed for either feature representation or demographic persistence, with a reserve network that achieves both goals simultaneously. As well as being practically applicable, our analyses also provide general insights into marine reserve planning for both representation and demographic persistence. First, persistence constraints for dispersive organisms are likely to be much harder to achieve than representation targets, due to their greater complexity. Second, persistence and representation constraints pull the reserve network design process in divergent directions, making it difficult to efficiently achieve both constraints. Although our method can be readily applied to the data-rich Keppel Islands case study, we finally consider the factors that limit the method’s utility in information-poor contexts common in marine conservation. PMID:27168206

Long-term monitoring of experimental features, subtask 2 : Alexandria-Ashland highway (KY 9) pavement performance monitoring

DOT National Transportation Integrated Search

2000-06-01

Construction on the AA Highway began in late 1985 and was completed in late 1990. Prior to construction, 30 different test sections had been designed into the highway for evaluation. The test sections contain 23 different characteristic qualities and...

Writing DNA with GenoCAD.

PubMed

Czar, Michael J; Cai, Yizhi; Peccoud, Jean

2009-07-01

Chemical synthesis of custom DNA made to order calls for software streamlining the design of synthetic DNA sequences. GenoCAD (www.genocad.org) is a free web-based application to design protein expression vectors, artificial gene networks and other genetic constructs composed of multiple functional blocks called genetic parts. By capturing design strategies in grammatical models of DNA sequences, GenoCAD guides the user through the design process. By successively clicking on icons representing structural features or actual genetic parts, complex constructs composed of dozens of functional blocks can be designed in a matter of minutes. GenoCAD automatically derives the construct sequence from its comprehensive libraries of genetic parts. Upon completion of the design process, users can download the sequence for synthesis or further analysis. Users who elect to create a personal account on the system can customize their workspace by creating their own parts libraries, adding new parts to the libraries, or reusing designs to quickly generate sets of related constructs.

A "Layers of Negotiation" Model for Designing Constructivist Learning Materials.

ERIC Educational Resources Information Center

Cennamo, Katherine S.; And Others

In designing materials for use in a contructivist learning environment, instructional designers still have a role in selecting the situations that may provide a stimulus for knowledge construction and providing features that support students and teachers in using these materials. This paper describes the process of designing a series of case-based…

Indoor airPLUS Videos, Podcasts, Webinars and Interviews

EPA Pesticide Factsheets

The Webinar presentations will help you discover how Indoor airPLUS homes are designed to improve indoor air quality and increase energy efficiency and learn about the key design and construction features included in Indoor airPLUS homes.

The Advanced Technology Solar Telescope: design and early construction

NASA Astrophysics Data System (ADS)

McMullin, Joseph P.; Rimmele, Thomas R.; Keil, Stephen L.; Warner, Mark; Barden, Samuel; Bulau, Scott; Craig, Simon; Goodrich, Bret; Hansen, Eric; Hegwer, Steve; Hubbard, Robert; McBride, William; Shimko, Steve; Wöger, Friedrich; Ditsler, Jennifer

2012-09-01

The National Solar Observatory’s (NSO) Advanced Technology Solar Telescope (ATST) is the first large U.S. solar telescope accessible to the worldwide solar physics community to be constructed in more than 30 years. The 4-meter diameter facility will operate over a broad wavelength range (0.35 to 28 μm ), employing adaptive optics systems to achieve diffraction limited imaging and resolve features approximately 20 km on the Sun; the key observational parameters (collecting area, spatial resolution, spectral coverage, polarization accuracy, low scattered light) enable resolution of the theoretically-predicted, fine-scale magnetic features and their dynamics which modulate the radiative output of the sun and drive the release of magnetic energy from the Sun’s atmosphere in the form of flares and coronal mass ejections. In 2010, the ATST received a significant fraction of its funding for construction. In the subsequent two years, the project has hired staff and opened an office on Maui. A number of large industrial contracts have been placed throughout the world to complete the detailed designs and begin constructing the major telescope subsystems. These contracts have included the site development, AandE designs, mirrors, polishing, optic support assemblies, telescope mount and coudé rotator structures, enclosure, thermal and mechanical systems, and high-level software and controls. In addition, design development work on the instrument suite has undergone significant progress; this has included the completion of preliminary design reviews (PDR) for all five facility instruments. Permitting required for physically starting construction on the mountaintop of Haleakalā, Maui has also progressed. This paper will review the ATST goals and specifications, describe each of the major subsystems under construction, and review the contracts and lessons learned during the contracting and early construction phases. Schedules for site construction, key factory testing of major subsystems, and integration, test and commissioning activities will also be discussed.

COST AND EFFECTIVENESS OF RADON RESISTANT FEATURES IN NEW SCHOOL BUILDINGS

EPA Science Inventory

The paper describes initial results of a study of several schools with radon resistant features that were recently constructed in the northeastern U. S. hese designs generally are based on experience with radon mitigation in existing houses and schools and radon- resistant new co...

10 CFR 50.35 - Issuance of construction permits. 1

Code of Federal Regulations, 2011 CFR

2011-01-01

... principal architectural and engineering criteria for the design, and has identified the major features or... features or components, if any, which require research and development have been described by the applicant and the applicant has identified, and there will be conducted, a research and development program...

10 CFR 50.35 - Issuance of construction permits. 1

Code of Federal Regulations, 2010 CFR

2010-01-01

... principal architectural and engineering criteria for the design, and has identified the major features or... features or components, if any, which require research and development have been described by the applicant and the applicant has identified, and there will be conducted, a research and development program...

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Results of a survey covering the safety, adequacy, and reliability of certain design and construction features pertaining to the NS Savannah nuclear power plant and related systems are presented. (auth)

THE NEW NORRIS HOUSE: A SUSTAINABLE HOME FOR THE 21ST CENTURY

EPA Science Inventory

In 1933 the Tennessee valley Authority constructed a model community, Norris, Tennessee, as part of the Norris Dam construction project. A key feature of this New Deal village was the Norris House, a series of home designs built as models for modern, efficient, and sustainable...

The building blocks of a 'Liveable Neighbourhood': Identifying the key performance indicators for walking of an operational planning policy in Perth, Western Australia.

PubMed

Hooper, Paula; Knuiman, Matthew; Foster, Sarah; Giles-Corti, Billie

2015-11-01

Planning policy makers are requesting clearer guidance on the key design features required to build neighbourhoods that promote active living. Using a backwards stepwise elimination procedure (logistic regression with generalised estimating equations adjusting for demographic characteristics, self-selection factors, stage of construction and scale of development) this study identified specific design features (n=16) from an operational planning policy ("Liveable Neighbourhoods") that showed the strongest associations with walking behaviours (measured using the Neighbourhood Physical Activity Questionnaire). The interacting effects of design features on walking behaviours were also investigated. The urban design features identified were grouped into the "building blocks of a Liveable Neighbourhood", reflecting the scale, importance and sequencing of the design and implementation phases required to create walkable, pedestrian friendly developments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experience of light thin-walled structures improvement in construction

NASA Astrophysics Data System (ADS)

Frolovskaia, A. V.; Deordiev, S. V.; Falk, A.; Klinduh, N. Y.; Terehova, I. I.

2018-05-01

The authors on the basis of practical experience have analyzed low-rise construction with the use of energy-saving technologies. Characteristic features of possible variants of frame construction are looked at and described. The relevance of the paper consists in the improvement of the building frame design solution based on the analysis and elimination of disadvantages taking into account consumers’ point of view.

A contribution to the availability of lunar resources for powered construction

NASA Technical Reports Server (NTRS)

Heppenheimer, T. A.

1980-01-01

The use of lunar resources to construct solar power satellites wherein the resources are transported by a lunar mass driver is discussed. The minimization of cross track errors in the launch of payloads by mass driver is emphasized. The design and construction of the mass driver is outlined. Features of the proposed system addressed include passive magnetic damping, separation and snapout, and downrange correction.

Evaluating Pavement Design Features: Five Year Performance Evaluation of FA 401 and FA 409

DOT National Transportation Integrated Search

1993-02-01

In the summer of 1986, the Illinois Department of Transportation began the construction of four demonstration projects which focused on evaluating proposed mechanistically-based asphalt concrete (AC) and Portland cement concrete (PCC) pavement design...

Engaging with Islamic Patterns

ERIC Educational Resources Information Center

Sugarman, Ian

2012-01-01

Islamic patterns were a regular feature in mathematics classrooms, and probably still feature in many wall displays. However, as part of the learning process, these ancient designs appear to have lost any significant contemporary appeal. Here, the power of software is engaged to bring the construction of Islamic type patterns up to date. Forget…

Low Impact Development Standards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loftin, Samuel R.

The goal of the LID Standards is to provide guidance on the planning, design, construction and maintenance of green infrastructure (GI) features at Los Alamos National Laboratory. The success of LID at LANL is dependent on maintaining a consistent approach to achieve effective application, operation, and maintenance of these storm water control features.

About the features of the design of X-ray systems for nondestructive control in industry

NASA Astrophysics Data System (ADS)

Bessonov, V. B.; Obodovskiy, A. V.; Potrakhov, Y. N.

2018-02-01

X-ray methods for nondestructive control take the priority place if necessary to exercise quality control of a product, to define presence of defects and to execute expert researches. In the present work, an attempt is made to systematize some features in the design and construction of installations for X-ray non-destructive control using the example of developments conducted at St. Petersburg State Electrotechnical University “LETI”.

Picking Up Artifacts: Storyboarding as a Gateway to Reuse

NASA Astrophysics Data System (ADS)

Wahid, Shahtab; Branham, Stacy M.; Cairco, Lauren; McCrickard, D. Scott; Harrison, Steve

Storyboarding offers designers the opportunity to illustrate a visual narrative of use. Because designers often refer to past ideas, we argue storyboards can be constructed by reusing shared artifacts. We present a study in which we explore how designers reuse artifacts consisting of images and rationale during storyboard construction. We find images can aid in accessing rationale and that connections among features aid in deciding what to reuse, creating new artifacts, and constructing. Based on requirements derived from our findings, we present a storyboarding tool, PIC-UP, to facilitate artifact sharing and reuse and evaluate its use in an exploratory study. We conclude with remarks on facilitating reuse and future work.

Advanced Extended Plate and Beam Wall System in a Cold-Climate House

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, Dave; Wiehagen, Joseph; Kochkin, Vladimir

This report presents the design and evaluation of an innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders.

Design and Construction of a Portable Oculometer for Use in Transportation Oriented Human Factors Studies

DOT National Transportation Integrated Search

1971-08-01

THE REPORT DESCRIBES DEVELOPMENT OF AN INSTRUMENT DESIGNED TO ACQUIRE AND PROCESS INFORMATION ABOUT HUMAN VISUAL PERFORMANCE. THE INSTRUMENT HAS THE FOLLOWING FEATURES: IT CAN BE OPERATED IN A VARIETY OF TRANSPORTATION ENVIRONMENTS INCLUDING SIMULATO...

Mojo Hand, a TALEN design tool for genome editing applications.

PubMed

Neff, Kevin L; Argue, David P; Ma, Alvin C; Lee, Han B; Clark, Karl J; Ekker, Stephen C

2013-01-16

Recent studies of transcription activator-like (TAL) effector domains fused to nucleases (TALENs) demonstrate enormous potential for genome editing. Effective design of TALENs requires a combination of selecting appropriate genetic features, finding pairs of binding sites based on a consensus sequence, and, in some cases, identifying endogenous restriction sites for downstream molecular genetic applications. We present the web-based program Mojo Hand for designing TAL and TALEN constructs for genome editing applications (http://www.talendesign.org). We describe the algorithm and its implementation. The features of Mojo Hand include (1) automatic download of genomic data from the National Center for Biotechnology Information, (2) analysis of any DNA sequence to reveal pairs of binding sites based on a user-defined template, (3) selection of restriction-enzyme recognition sites in the spacer between the TAL monomer binding sites including options for the selection of restriction enzyme suppliers, and (4) output files designed for subsequent TALEN construction using the Golden Gate assembly method. Mojo Hand enables the rapid identification of TAL binding sites for use in TALEN design. The assembly of TALEN constructs, is also simplified by using the TAL-site prediction program in conjunction with a spreadsheet management aid of reagent concentrations and TALEN formulation. Mojo Hand enables scientists to more rapidly deploy TALENs for genome editing applications.

UPLOAD: THE NEW NORRIS HOUSE – A SUSTAINABLE HOME FOR THE 21ST CENTURY

EPA Science Inventory

In 1933 the Tennessee Valley Authority constructed a model community, Norris, Tennessee, as part of the Norris Dam construction project. A key feature of this New Deal village was the Norris House, a series of home designs built as models for modern, efficient, and sustain...

78 FR 65233 - Special Conditions: Bombardier Inc., Models BD-500-1A10 and BD-500-1A11 Series Airplanes...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... a novel or unusual design feature associated with aluminum-lithium fuselage construction that may... of the Bombardier C-series airplanes will be fabricated using aluminum-lithium construction. Structure fabricated from aluminum-lithium may provide different levels of protection from post-crash fuel...

Nuclear Powerplant Safety: Design and Planning.

ERIC Educational Resources Information Center

Department of Energy, Washington, DC. Nuclear Energy Office.

The most important concern in the design, construction and operation of nuclear powerplants is safety. Nuclear power is one of the major contributors to the nation's supply of electricity; therefore, it is important to assure its safe use. Each different type of powerplant has special design features and systems to protect health and safety. One…

76 FR 6820 - Contract for Hydroelectric Power Development at the C-Drop, a Feature of the Klamath Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-08

... Acquisition and Easements, Hydraulics and Hydrology, Water Rights, Project Features and Design, Power... Federal water resource projects, Reclamation will consider proposals for non-Federal development of... part of the Klamath Project, the United States constructed A, B, and C-Canals, which carry water south...

Are green building features safe for preventive maintenance workers? Examining the evidence.

PubMed

Omar, Mohamed Shamun; Quinn, Margaret M; Buchholz, Bryan; Geiser, Ken

2013-04-01

Many newly constructed green buildings (GB) are certified using the United States Green Building Council (USGBC) Leadership in Energy and Environmental Design (LEED) rating system for new construction and major renovation which focuses on architectural and mechanical design to conserve energy, reduce environmental harm, and enhance indoor quality for occupants. This study evaluated the preventive maintenance (PM) worker occupational safety and health (OSH) risks related to the design of GB. PM job hazard analyses (JHA) were performed on the tasks required to operate and maintain five GB features selected from 13 LEED certified GB. A 22-item JHA and OSH risk scoring system were developed. Potentially serious OSH hazards included: green roofs made of slippery material without fall protection; energy recovery wheels and storm water harvesting systems in confined spaces; skylights without guard rails; and tight geothermal well mechanical rooms constraining safe preventive practices. GB can present PM OSH risks and these should be eliminated in the building design phase. Copyright © 2013 Wiley Periodicals, Inc.

Design of 240,000 orthogonal 25mer DNA barcode probes.

PubMed

Xu, Qikai; Schlabach, Michael R; Hannon, Gregory J; Elledge, Stephen J

2009-02-17

DNA barcodes linked to genetic features greatly facilitate screening these features in pooled formats using microarray hybridization, and new tools are needed to design large sets of barcodes to allow construction of large barcoded mammalian libraries such as shRNA libraries. Here we report a framework for designing large sets of orthogonal barcode probes. We demonstrate the utility of this framework by designing 240,000 barcode probes and testing their performance by hybridization. From the test hybridizations, we also discovered new probe design rules that significantly reduce cross-hybridization after their introduction into the framework of the algorithm. These rules should improve the performance of DNA microarray probe designs for many applications.

Design of 240,000 orthogonal 25mer DNA barcode probes

PubMed Central

Xu, Qikai; Schlabach, Michael R.; Hannon, Gregory J.; Elledge, Stephen J.

2009-01-01

DNA barcodes linked to genetic features greatly facilitate screening these features in pooled formats using microarray hybridization, and new tools are needed to design large sets of barcodes to allow construction of large barcoded mammalian libraries such as shRNA libraries. Here we report a framework for designing large sets of orthogonal barcode probes. We demonstrate the utility of this framework by designing 240,000 barcode probes and testing their performance by hybridization. From the test hybridizations, we also discovered new probe design rules that significantly reduce cross-hybridization after their introduction into the framework of the algorithm. These rules should improve the performance of DNA microarray probe designs for many applications. PMID:19171886

SKL algorithm based fabric image matching and retrieval

NASA Astrophysics Data System (ADS)

Cao, Yichen; Zhang, Xueqin; Ma, Guojian; Sun, Rongqing; Dong, Deping

2017-07-01

Intelligent computer image processing technology provides convenience and possibility for designers to carry out designs. Shape analysis can be achieved by extracting SURF feature. However, high dimension of SURF feature causes to lower matching speed. To solve this problem, this paper proposed a fast fabric image matching algorithm based on SURF K-means and LSH algorithm. By constructing the bag of visual words on K-Means algorithm, and forming feature histogram of each image, the dimension of SURF feature is reduced at the first step. Then with the help of LSH algorithm, the features are encoded and the dimension is further reduced. In addition, the indexes of each image and each class of image are created, and the number of matching images is decreased by LSH hash bucket. Experiments on fabric image database show that this algorithm can speed up the matching and retrieval process, the result can satisfy the requirement of dress designers with accuracy and speed.

The 2-MM Range Receiving Module for Observations of Atmospheric Ozone Emission Line at 142.2 GHz

NASA Astrophysics Data System (ADS)

Piddyachiy, V. I.; Korolev, O. M.; Myshenko, V. V.; Shulga, V. M.

2015-09-01

A low-noise uncooled receiver was designed and constructed for measurements of the atmospheric ozone spectral line at 142.2 GHz. The design has shown the double-sideband (DSB) receiver noise temperature of about 350 K within 130 to 150 GHz. Critical construction features of the basic units (mixer, intermediate frequency amplifier, and diplexer) are described. Noise characteristics showed by the receiver are the best in the class of uncooled heterodyne receivers of the 2-mm wavelengths.

High Temperature, Permanent Magnet Biased, Fault Tolerant, Homopolar Magnetic Bearing Development

NASA Technical Reports Server (NTRS)

Palazzolo, Alan; Tucker, Randall; Kenny, Andrew; Kang, Kyung-Dae; Ghandi, Varun; Liu, Jinfang; Choi, Heeju; Provenza, Andrew

2008-01-01

This paper summarizes the development of a magnetic bearing designed to operate at 1,000 F. A novel feature of this high temperature magnetic bearing is its homopolar construction which incorporates state of the art high temperature, 1,000 F, permanent magnets. A second feature is its fault tolerance capability which provides the desired control forces with over one-half of the coils failed. The construction and design methodology of the bearing is outlined and test results are shown. The agreement between a 3D finite element, magnetic field based prediction for force is shown to be in good agreement with predictions at room and high temperature. A 5 axis test rig will be complete soon to provide a means to test the magnetic bearings at high temperature and speed.

10 CFR 60.142 - Design testing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... construction, a program for in situ testing of such features as borehole and shaft seals, backfill, and the... 10 Energy 2 2010-01-01 2010-01-01 false Design testing. 60.142 Section 60.142 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES...

10 CFR 60.142 - Design testing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... construction, a program for in situ testing of such features as borehole and shaft seals, backfill, and the... 10 Energy 2 2013-01-01 2013-01-01 false Design testing. 60.142 Section 60.142 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES...

10 CFR 60.142 - Design testing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... construction, a program for in situ testing of such features as borehole and shaft seals, backfill, and the... 10 Energy 2 2012-01-01 2012-01-01 false Design testing. 60.142 Section 60.142 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES...

10 CFR 60.142 - Design testing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... construction, a program for in situ testing of such features as borehole and shaft seals, backfill, and the... 10 Energy 2 2014-01-01 2014-01-01 false Design testing. 60.142 Section 60.142 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES...

10 CFR 60.142 - Design testing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... construction, a program for in situ testing of such features as borehole and shaft seals, backfill, and the... 10 Energy 2 2011-01-01 2011-01-01 false Design testing. 60.142 Section 60.142 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES...

Design and fabrication of a prototype system for a photovoltaic residence in the Northeast

NASA Astrophysics Data System (ADS)

1982-08-01

This project consisted of the design, fabrication, and testing of a photovoltaic residence which is suitable for construction in the Northeast. A full size residence was designed which included energy conserving and passive features, and the energy performance of the residence was completed for a 5 kW PV array in a standoff configuration. Actual construction consisted of the roof structure and a building enclosure large enough to contain the PCU, test equipment, and load simulation equipment. The PV array consists of 78 modules along with a line tie inverter.

Theory, construction and operation of simple tensiometers.

USGS Publications Warehouse

Stannard, D.I.

1986-01-01

The tensiometer presented here in detail is suited to diverse on-site applications. Constructed from readily available, inexpensive parts, it can measure as much as 0.85 bar of tension. Design features include a flushing system for removal of entrapped air or mercury, and an easily maintained modular network of nylon manometers and water-supply tubes. -from Author

Design of electric vehicle charging station based on wind and solar complementary power supply

NASA Astrophysics Data System (ADS)

Wang, Li

2018-05-01

Electric vehicles have become a major trend in the development of the automobile industry. Green energy saving is an important feature of their development. At the same time, the related charging facilities construction is also critical. If we improve the charging measures to adapt to its green energy-saving features, it will be to a greater extent to promote its further development. This article will propose a highly efficient green energy-saving charging station designed for the electric vehicles.

The Use of Executive Control Processes in Engineering Design by Engineering Students and Professional Engineers

ERIC Educational Resources Information Center

Dixon, Raymond A.; Johnson, Scott D.

2012-01-01

A cognitive construct that is important when solving engineering design problems is executive control process, or metacognition. It is a central feature of human consciousness that enables one "to be aware of, monitor, and control mental processes." The framework for this study was conceptualized by integrating the model for creative design, which…

Design of a 1-kWh bipolar nickel hydrogen battery

NASA Technical Reports Server (NTRS)

Cataldo, R. L.

1984-01-01

The design of a nickel hydrogen battery utilizing bipolar construction in a common pressure vessel is discussed. Design features are as follows: 40 ampere-hour capcity, 1 kWh stored energy as a 24 cell battery, 1.8 kW delivered in a LEO Cycle and maximum pulse power of 18.0 kW.

Two decades (1993-2012) of adult intensive care unit design: a comparative study of the physical design features of the best practice examples.

PubMed

Rashid, Mahbub

2014-01-01

In 2006, Critical Care Nursing Quarterly published a study of the physical design features of a set of best practice example adult intensive care units (ICUs). These adult ICUs were awarded between 1993 and 2003 by the Society of Critical Care Medicine (SCCM), the American Association of Critical-Care Nurses, and the American Institute of Architects/Academy of Architecture for Health for their efforts to promote the critical care unit environment through design. Since 2003, several more adult ICUs were awarded by the same organizations for similar efforts. This study includes these newer ICUs along with those of the previous study to cover a period of 2 decades from 1993 to 2012. Like the 2006 study, this study conducts a systematic content analysis of the materials submitted by the award-winning adult ICUs. On the basis of the analysis, the study compares the 1993-2002 and 2003-2012 adult ICUs in relation to construction type, unit specialty, unit layout, unit size, patient room size and design, support and service area layout, and family space design. The study also compares its findings with the 2010 Guidelines for Design and Construction of Health Care Facilities of the Facility Guidelines Institute and the 2012 Guidelines for Intensive Care Unit Design of the SCCM. The study indicates that the award-winning ICUs of both decades used several design features that were associated with positive outcomes in research studies. The study also indicates that the award-winning ICUs of the second decade used more evidence-based design features than those of the first decades. In most cases, these ICUs exceeded the requirements of the Facility Guidelines Institute Guidelines to meet those of the SCCM Guidelines. Yet, the award-winning ICUs of both decades also used several features that had very little or no supporting research evidence. Since they all were able to create an optimal critical care environment for which they were awarded, having knowledge of the physical design of these award-winning ICUs may help design better ICUs.

Multiloop Integral System Test (MIST): MIST Facility Functional Specification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habib, T F; Koksal, C G; Moskal, T E

1991-04-01

The Multiloop Integral System Test (MIST) is part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox designed plants. MIST is sponsored by the US Nuclear Regulatory Commission, the Babcock Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral facilities to address the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility --more » the Once Through Integral System (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST Functional Specification documents as-built design features, dimensions, instrumentation, and test approach. It also presents the scaling basis for the facility and serves to define the scope of work for the facility design and construction. 13 refs., 112 figs., 38 tabs.« less

Use of a New Set of Linguistic Features to Improve Automatic Assessment of Text Readability

ERIC Educational Resources Information Center

Yoshimi, Takehiko; Kotani, Katsunori; Isahara, Hitoshi

2012-01-01

The present paper proposes and evaluates a readability assessment method designed for Japanese learners of EFL (English as a foreign language). The proposed readability assessment method is constructed by a regression algorithm using a new set of linguistic features that were employed separately in previous studies. The results showed that the…

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2012 CFR

2012-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″×10″) of the equipment of sufficient clarity to reveal equipment construction and layout...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2010 CFR

2010-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″×10″) of the equipment of sufficient clarity to reveal equipment construction and layout...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2011 CFR

2011-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″×10″) of the equipment of sufficient clarity to reveal equipment construction and layout...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2014 CFR

2014-10-01

... to comply with the design requirements of all parts of § 15.121 of this chapter. The application must... describing the design features that prevent the modification of the equipment by the user to receive... equipment construction and layout, including meters, if any, and labels for controls and meters and...

47 CFR 2.1033 - Application for certification.

Code of Federal Regulations, 2013 CFR

2013-10-01

... include a statement describing the methods used to comply with the design requirements of all parts of... vulnerability of the equipment to possible modification and describing the design features that prevent the...) Photographs (8″ × 10″) of the equipment of sufficient clarity to reveal equipment construction and layout...

Peculiarities of Clutch Forming Rails and Wheel Block Construction

NASA Astrophysics Data System (ADS)

Shiler, V. V.; Galiev, I. I.; Shiler, A. V.

2018-03-01

The clutch of the wheel and rail is significantly influenced by the design features of the standard wheel pair, which are manifested in the presence of "parasitic" slipping of the wheels along the rails during its movement. The purpose of the presented work is to evaluate new design solutions for wheel sets. The research was carried out using methods of comparative simulation modelling and physical prototyping. A new design of the wheel pair (block wheel pair) is proposed, which features an independent rotation of all surfaces of the wheels in contact with the rails. The block construction of the wheel pair forms open mechanical contours with the track gauge, which completely eliminates the "parasitic" slippage. As a result, in the process of implementing traction or braking forces, the coupling coefficient of the block construction of the wheel pair is significantly higher than that of existing structures. In addition, in the run-out mode, the resistance to movement of the block wheel pair is half as much. All this will allow one to significantly reduce the energy consumption for traction of trains, wear of track elements and crew, and to increase the speed and safety of train traffic.

Static design of steel-concrete lining for traffic tunnels

NASA Astrophysics Data System (ADS)

Vojtasik, Karel; Mohyla, Marek; Hrubesova, Eva

2017-09-01

Article summarizes the results of research focused on the structural design of traffic tunnel linings that have been achieved in the framework of a research project TE01020168 that supports The Technology Agency of Czech Republic. This research aim is to find and develop a process for design structure parameters of tunnel linings. These are now mostly build up by a shotcrete technology. The shotcrete is commonly endorsed either with steel girders or steel fibres. Since the installation a lining structure is loaded while strength and deformational parameters of shotcrete start to rise till the setting time elapses. That’s reason why conventional approaches of reinforced concrete are not suitable. As well as there are other circumstances to step in shown in this article. Problem is solved by 3D analysis using numerical model that takes into account all the significant features of a tunnel lining construction process inclusive the interaction between lining structure with rock massive. Analysis output is a view into development of stress-strain state in respective construction parts of tunnel lining the whole structure around, including impact on stability of rock massive. The proposed method comprises all features involved in tunnel fabrication including geotechnics and construction technologies.

Living Shoreline Designs in Urban Systems: Examples from New York and Baltimore Harbors

NASA Astrophysics Data System (ADS)

Doss, T.

2017-12-01

In the aftermath of Hurricanes Irene and Sandy, there was a renewed interest in protecting our shorelines and restoring community resiliency by using natural and nature based features. We observed in the wake of these storms that those shorelines that had been protected by natural features sustained less damage. But how well can we mimic these natural features? And how do we determine which strategy is best along a given shoreline? A series of living shoreline pilot projects are presented, highlighting the design and construction for the different strategies and how they are being monitored and adapted to sea level rise.

33 CFR 155.120 - Equivalents.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (a) For ships required to be surveyed under § 151.17 of this chapter, the Commandant may, upon... operational methods to control the discharge of oil in place of those design and construction features...

33 CFR 155.120 - Equivalents.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (a) For ships required to be surveyed under § 151.17 of this chapter, the Commandant may, upon... operational methods to control the discharge of oil in place of those design and construction features...

38 CFR 39.31 - Preapplication requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... documentation, as needed). (4) A design concept describing the major features of the project including the... space, or functional layout; and it will not enter into a construction contract for the project or...

38 CFR 39.31 - Preapplication requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... documentation, as needed). (4) A design concept describing the major features of the project including the... space, or functional layout; and it will not enter into a construction contract for the project or...

33 CFR 148.725 - What are the design, construction and operational criteria?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: GENERAL Environmental Review... permanent interference with natural processes or features that are important to natural currents and wave...

Accessible cell phone design: development and application of a needs analysis framework.

PubMed

Smith-Jackson, Tonya; Nussbaum, Maury; Mooney, Aaron

2003-05-20

This research describes the development and use of the Needs Analysis and Requirements Acquisition (NARA) framework to elicit and construct user requirements for the design of cell phones (which are a type of assistive technology) that are both usable and accessible to persons with disabilities. Semi-structured interviews and a focus group were used to elicit information and a systematic approach was used to translation information into requirements (construct). Elicitation and construction are the first two stages of NARA. Requirements for general and feature-specific phone attributes were identified, and several requirements were found to match six of the seven universal design principles. The study demonstrated that NARA is both a straight-forward and cost-effective method to develop user requirements and can be used throughout the development cycle.

Computational Tools and Algorithms for Designing Customized Synthetic Genes

PubMed Central

Gould, Nathan; Hendy, Oliver; Papamichail, Dimitris

2014-01-01

Advances in DNA synthesis have enabled the construction of artificial genes, gene circuits, and genomes of bacterial scale. Freedom in de novo design of synthetic constructs provides significant power in studying the impact of mutations in sequence features, and verifying hypotheses on the functional information that is encoded in nucleic and amino acids. To aid this goal, a large number of software tools of variable sophistication have been implemented, enabling the design of synthetic genes for sequence optimization based on rationally defined properties. The first generation of tools dealt predominantly with singular objectives such as codon usage optimization and unique restriction site incorporation. Recent years have seen the emergence of sequence design tools that aim to evolve sequences toward combinations of objectives. The design of optimal protein-coding sequences adhering to multiple objectives is computationally hard, and most tools rely on heuristics to sample the vast sequence design space. In this review, we study some of the algorithmic issues behind gene optimization and the approaches that different tools have adopted to redesign genes and optimize desired coding features. We utilize test cases to demonstrate the efficiency of each approach, as well as identify their strengths and limitations. PMID:25340050

38 CFR 39.31 - Preapplication requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) A design concept describing the major features of the project including the number and types of... project, use of space, or functional layout; and it will not enter into a construction contract for the...

Impact evaluation of composite floor sections

NASA Technical Reports Server (NTRS)

Boitnott, Richard L.; Fasanella, Edwin L.

1989-01-01

Graphite-epoxy floor sections representative of aircraft fuselage construction were statically and dynamically tested to evaluate their response to crash loadings. These floor sections were fabricated using a frame-stringer design typical of present aluminum aircraft without features to enhance crashworthiness. The floor sections were tested as part of a systematic research program developed to study the impact response of composite components of increasing complexity. The ultimate goal of the research program is to develop crashworthy design features for future composite aircraft. Initially, individual frames of six-foot diameter were tested both statically and dynamically. The frames were then used to construct built-up floor sections for dynamic tests at impact velocities of approximately 20 feet/sec to simulate survivable crash velocities. In addition, static tests were conducted to gain a better understanding of the failure mechanisms seen in the dynamic tests.

Genetic Constructor: An Online DNA Design Platform.

PubMed

Bates, Maxwell; Lachoff, Joe; Meech, Duncan; Zulkower, Valentin; Moisy, Anaïs; Luo, Yisha; Tekotte, Hille; Franziska Scheitz, Cornelia Johanna; Khilari, Rupal; Mazzoldi, Florencio; Chandran, Deepak; Groban, Eli

2017-12-15

Genetic Constructor is a cloud Computer Aided Design (CAD) application developed to support synthetic biologists from design intent through DNA fabrication and experiment iteration. The platform allows users to design, manage, and navigate complex DNA constructs and libraries, using a new visual language that focuses on functional parts abstracted from sequence. Features like combinatorial libraries and automated primer design allow the user to separate design from construction by focusing on functional intent, and design constraints aid iterative refinement of designs. A plugin architecture enables contributions from scientists and coders to leverage existing powerful software and connect to DNA foundries. The software is easily accessible and platform agnostic, free for academics, and available in an open-source community edition. Genetic Constructor seeks to democratize DNA design, manufacture, and access to tools and services from the synthetic biology community.

Design Features for Linguistically-Mediated Meaning Construction: The Relative Roles of the Linguistic and Conceptual Systems in Subserving the Ideational Function of Language

PubMed Central

Evans, Vyvyan

2016-01-01

Recent research in language and cognitive science proposes that the linguistic system evolved to provide an “executive” control system on the evolutionarily more ancient conceptual system (e.g., Barsalou et al., 2008; Evans, 2009, 2015a,b; Bergen, 2012). In short, the claim is that embodied representations in the linguistic system interface with non-linguistic representations in the conceptual system, facilitating rich meanings, or simulations, enabling linguistically mediated communication. In this paper I build on these proposals by examining the nature of what I identify as design features for this control system. In particular, I address how the ideational function of language—our ability to deploy linguistic symbols to convey meanings of great complexity—is facilitated. The central proposal of this paper is as follows. The linguistic system of any given language user, of any given linguistic system—spoken or signed—facilitates access to knowledge representation—concepts—in the conceptual system, which subserves this ideational function. In the most general terms, the human meaning-making capacity is underpinned by two distinct, although tightly coupled representational systems: the conceptual system and the linguistic system. Each system contributes to meaning construction in qualitatively distinct ways. This leads to the first design feature: given that the two systems are representational—they are populated by semantic representations—the nature and function of the representations are qualitatively different. This proposed design feature I term the bifurcation in semantic representation. After all, it stands to reason that if a linguistic system has a different function, vis-à-vis the conceptual system, which is of far greater evolutionary antiquity, then the semantic representations will be complementary, and as such, qualitatively different, reflecting the functional distinctions of the two systems, in collectively giving rise to meaning. I consider the nature of these qualitatively distinct representations. And second, language itself is adapted to the conceptual system—the semantic potential—that it marshals in the meaning construction process. Hence, a linguistic system itself exhibits a bifurcation, in terms of the symbolic resources at its disposal. This design feature I dub the birfucation in linguistic organization. As I shall argue, this relates to two distinct reference strategies available for symbolic encoding in language: what I dub words-to-world reference and words-to-words reference. In slightly different terms, this design feature of language amounts to a distinction between a lexical subsystem, and a grammatical subsystem. PMID:26925000

Design Features for Linguistically-Mediated Meaning Construction: The Relative Roles of the Linguistic and Conceptual Systems in Subserving the Ideational Function of Language.

PubMed

Evans, Vyvyan

2016-01-01

Recent research in language and cognitive science proposes that the linguistic system evolved to provide an "executive" control system on the evolutionarily more ancient conceptual system (e.g., Barsalou et al., 2008; Evans, 2009, 2015a,b; Bergen, 2012). In short, the claim is that embodied representations in the linguistic system interface with non-linguistic representations in the conceptual system, facilitating rich meanings, or simulations, enabling linguistically mediated communication. In this paper I build on these proposals by examining the nature of what I identify as design features for this control system. In particular, I address how the ideational function of language-our ability to deploy linguistic symbols to convey meanings of great complexity-is facilitated. The central proposal of this paper is as follows. The linguistic system of any given language user, of any given linguistic system-spoken or signed-facilitates access to knowledge representation-concepts-in the conceptual system, which subserves this ideational function. In the most general terms, the human meaning-making capacity is underpinned by two distinct, although tightly coupled representational systems: the conceptual system and the linguistic system. Each system contributes to meaning construction in qualitatively distinct ways. This leads to the first design feature: given that the two systems are representational-they are populated by semantic representations-the nature and function of the representations are qualitatively different. This proposed design feature I term the bifurcation in semantic representation. After all, it stands to reason that if a linguistic system has a different function, vis-à-vis the conceptual system, which is of far greater evolutionary antiquity, then the semantic representations will be complementary, and as such, qualitatively different, reflecting the functional distinctions of the two systems, in collectively giving rise to meaning. I consider the nature of these qualitatively distinct representations. And second, language itself is adapted to the conceptual system-the semantic potential-that it marshals in the meaning construction process. Hence, a linguistic system itself exhibits a bifurcation, in terms of the symbolic resources at its disposal. This design feature I dub the birfucation in linguistic organization. As I shall argue, this relates to two distinct reference strategies available for symbolic encoding in language: what I dub words-to-world reference and words-to-words reference. In slightly different terms, this design feature of language amounts to a distinction between a lexical subsystem, and a grammatical subsystem.

Design and construction of a remote piloted flying wing. B.S. Thesis

NASA Technical Reports Server (NTRS)

Costa, Alfred J.; Koopman, Fritz; Soboleski, Craig; Trieu, Thai-Ba; Duquette, Jaime; Krause, Scott; Susko, David; Trieu, Thuyba

1994-01-01

Currently, there is a need for a high-speed, high-lift civilian transport. Although unconventional, a flying wing could fly at speeds in excess of Mach 2 and still retain the capacity of a 747. The design of the flying wing is inherently unstable since it lacks a fuselage and a horizontal tail. The project goal was to design, construct, fly, and test a remote-piloted scale model flying wing. The project was completed as part of the NASA/USRA Advanced Aeronautics Design Program. These unique restrictions required us to implement several fundamental design changes from last year's Elang configuration including wing sweepback and wingtip endplates. Unique features such as a single ducted fan engine, composite structural materials, and an electrostatic stability system were incorporated. The result is the Banshee '94. Our efforts will aid future projects in design and construction techniques so that a viable flying wing can become an integral part of the aviation industry.

The magic of solar adobe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thayer, B.M.

1996-01-01

This article describes the energy efficient features of a house in Santa Fe. It is a modern version of ancient adobe house of the area. The homes solar features added no net cost to its construction and save more than 80% on conventional energy use. Topic areas covered are as follows: art of adobe; solar design; back-up heat; energy and cost performance.

An Empirical Analysis of the Effectiveness of Design-Build Construction Contracts

DTIC Science & Technology

1993-08-01

features and benefits with traditional design/bid/build. Several types of design/build organizations are examined, with their relative advantages and... benefits transferable to government contracting? Perhaps the most logical approach would be to compare point by point the various advantages and...consider to be critical to their competitive advantage in the market. This paper opens with a review of the development of design/build, then contrasts its

Design of the advanced regional aircraft, the DART-75

NASA Technical Reports Server (NTRS)

Elliott, Steve; Gislason, Jason; Huffstetler, Mark; Mann, Jon; Withers, Ashley; Zimmerman, Mark

1992-01-01

This design analysis is intended to show the capabilities of the DART-75, a 75 passenger medium-range regional transport. Included are the detailed descriptions of the structures, performance, stability and control, weight and balance, and engine design. The design should allow for the DART to become the premier regional aircraft of the future due to some advanced features like the canard, semi-composite construction, and advanced engines.

Development and Evaluation of Sensor Concepts for Ageless Aerospace Vehicles: Report 3 - Design of the Concept Demonstrator

NASA Technical Reports Server (NTRS)

Abbott, David; Ables, Jon; Batten, Adam; Carpenter, David; Collings, Tony; Doyle, Briony; Dunlop, John; Edwards, Graeme; Farmer, Tony; Gaffney, Bruce;

Semantics and technologies in modern design of interior stairs

NASA Astrophysics Data System (ADS)

Kukhta, M.; Sokolov, A.; Pelevin, E.

2015-10-01

Use of metal in the design of interior stairs presents new features for shaping, and can be implemented using different technologies. The article discusses the features of design and production technologies of forged metal spiral staircase considering the image semantics based on the historical and cultural heritage. To achieve the objective was applied structural- semantic method (to identify the organization of structure and semantic features of the artistic image), engineering methods (to justify the construction of the object), anthropometry method and ergonomics (to provide usability), methods of comparative analysis (to reveale the features of the way the ladder in different periods of culture). According to the research results are as follows. Was revealed the semantics influence on the design of interior staircase that is based on the World Tree image. Also was suggested rational calculation of steps to ensure the required strength. And finally was presented technology, providing the realization of the artistic image. In the practical part of the work is presented version of forged staircase.

78 FR 53498 - Petition for Exemption From the Vehicle Theft Prevention Standard; Fuji Heavy Industries U.S.A...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-29

... identity, design, and location of the components of the antitheft device for the Subaru [confidential.... Additionally, FUSA stated that because the immobilization features are designed and constructed within the... provided a comparative table showing how its device is similar to other manufacturers' devices that have...

30 CFR 18.68 - Tests for intrinsic safety.

Code of Federal Regulations, 2012 CFR

2012-07-01

... requirements may be added at any time if features of construction or use or both indicate them to be necessary.... They shall be designed to withstand a test voltage of 1,500 volts. (4) Intrinsically safe circuits shall be so designed that after failure of a single component, and subsequent failures resulting from...

30 CFR 18.68 - Tests for intrinsic safety.

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements may be added at any time if features of construction or use or both indicate them to be necessary.... They shall be designed to withstand a test voltage of 1,500 volts. (4) Intrinsically safe circuits shall be so designed that after failure of a single component, and subsequent failures resulting from...

30 CFR 18.68 - Tests for intrinsic safety.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements may be added at any time if features of construction or use or both indicate them to be necessary.... They shall be designed to withstand a test voltage of 1,500 volts. (4) Intrinsically safe circuits shall be so designed that after failure of a single component, and subsequent failures resulting from...

30 CFR 18.68 - Tests for intrinsic safety.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requirements may be added at any time if features of construction or use or both indicate them to be necessary.... They shall be designed to withstand a test voltage of 1,500 volts. (4) Intrinsically safe circuits shall be so designed that after failure of a single component, and subsequent failures resulting from...

Rotor systems research aircraft predesign study. Volume 4: Preliminary draft detail specification

NASA Technical Reports Server (NTRS)

Miller, A. N.; Linden, A. W.

1972-01-01

The RSRA requirements are presented in a detail specification format. Coverage of the requirements includes the following headings: (1) aircraft characteristics, (2) general features of design and construction, (3) aerodynamics, (4) structural design criteria, (5) flight control system, (6) propulsion subsystem, and (7) secondary power and distribution subsystem.

SRB thermal curtain design support

NASA Technical Reports Server (NTRS)

Dixon, Carl A.; Lundblad, Wayne E.; Koenig, John R.

1992-01-01

Improvements in SRB Thermal Curtain were identified by thermal design featuring: selection of materials capable of thermal protection and service temperatures by tri-layering quartz, S2 glass, and Kevlar in thinner cross section; weaving in single piece (instead of 24 sections) to achieve improved strength; and weaving to reduce manufacturing cost with angle interlock construction.

The UK Ion Thruster System and a Proposed Future Programme.

DTIC Science & Technology

1977-05-01

design and constructional features 13 1.2.3 The hollow cathode assembly 14 1.2.4 Isolators 16 1.2.5 Vaporisers 17 1.2.6 The neutraliser system 19 1.2.7... constructed and integrated with the thrus ter by MSDS Ltd)3, and is now undergoing modifications in light of the more recent experience gained in operating...measurements of virtuall y all the materials emitted by the thruster. The latter requirement has necessitated the construction of a complex system of probes

Construction of a low-cost detector to identify dissolved metals in aqueous media by fluorescence spectroscopy: design and perspectives.

NASA Astrophysics Data System (ADS)

González, M.; Montaño, M.; Hoyo, C.

2017-01-01

We have constructed a low cost fluorescence detector model to determine the presence of some heavy metals in an aqueous medium. In particular, we focus on metals which cause public health problems in our country. We did the first tests with standard samples of Hg (II). The innovative features of this instrument are its small dimensions (9 dm3) and the low cost of materials used in its construction.

Evaluation of experimental flexible pavements : final report.

DOT National Transportation Integrated Search

1979-01-01

The construction and performance of seven Virginia flexible pavements containing at least some experimental features were evaluated. The objective was to evaluate the performance of the pavements incorporating new or timely design concepts and to ass...

Operational Experience from Solar Thermal Energy Projects

NASA Technical Reports Server (NTRS)

Cameron, C. P.

1984-01-01

Over the past few years, Sandia National Laboratories were involved in the design, construction, and operation of a number of DOE-sponsored solar thermal energy systems. Among the systems currently in operation are several industrial process heat projects and the Modular Industrial Solar Retrofit qualification test systems, all of which use parabolic troughs, and the Shenandoah Total Energy Project, which uses parabolic dishes. Operational experience has provided insight to both desirable and undesirable features of the designs of these systems. Features of these systems which are also relevant to the design of parabolic concentrator thermal electric systems are discussed. Other design features discussed are system control functions which were found to be especially convenient or effective, such as local concentrator controls, rainwash controls, and system response to changing isolation. Drive systems are also discussed with particular emphasis of the need for reliability and the usefulness of a manual drive capability.

Design report small-scale fuel alcohol plant. Volume 2: Detailed construction information

NASA Astrophysics Data System (ADS)

1980-12-01

The objectives are to provide potential alcohol producers with a reference design and provide a complete, demonstrated design of a small scale fuel alcohol plant. The plant has the capability for feedstock preparation, cooking, saccharification, fermentation, distillation, by-product dewatering, and process steam generation. An interesting feature is an instrumentation and control system designed to allow the plant to run 24 hours per day with only four hours of operator attention.

[Construction-cost assessment of a program designed to promote physical and sports activities and prevent doping behaviors: PN-APSD - on 2002-2007].

PubMed

Bérard, A; Bréchat, P-H; Rymer, R; Londsdorfer, J

2009-02-01

According to the framework legislation promulgated as part of the reform of finance laws in France, quality is a mandatory feature of all governmental actions. In this context, this work was conducted to assess the construction cost of a national health program designed to promote physical and sports activities and prevent doping behaviors. This program was considered to have the characteristic features of a successful governmental health intervention. Four cost categories were evaluated: cost of the activity itself, transportation costs, communication costs and promotion costs. It was found that the program costs for 2002-2007 were 100,000 euro, with 15% of the costs in the communication category. Economic elements could be associated with factors of successful health service interventions in order to help decision makers responsible for the public interest and the consistency of public health actions.

A Cost-Effective Optical Device for the Characterization of Liquid Crystals

ERIC Educational Resources Information Center

Millier, Brian; Aleman Milán, Gianna

2014-01-01

The design and construction of an apparatus to measure the optical birefringence of a liquid crystal is described. The instrument also includes temperature control and monitoring circuitry to allow for the measurement of the nematic-to-isotropic phase transition temperature. An important feature of this design is that the students are able to…

FPL designs meet family housing needs

Treesearch

G. E. Sherwood

1972-01-01

The Forest Products Laboratory (FPL) has developed five house plans for low-cost rural houses to demonstrate cost-saving principles of construction, The plans feature simplicity of design, but provide structurally sound houses that fulfill the needs of many families. To determine to what extent the plans were used, how they met the needs and the acceptance standards of...

Features and perspectives of automatized construction crane-manipulators

NASA Astrophysics Data System (ADS)

Stepanov, Mikhail A.; Ilukhin, Peter A.

2018-03-01

Modern construction industry still has a high percentage of manual labor, and the greatest prospects of improving the construction process are lying in the field of automatization. In this article automatized construction manipulator-cranes are being studied in order to achieve the most rational design scheme. This is done through formulating a list of general conditions necessary for such cranes and a set of specialized kinematical conditions. A variety of kinematical schemes is evaluated via these conditions, and some are taken for further dynamical analisys. The comparative dynamical analisys of taken schemes was made and the most rational scheme was defined. Therefore a basis for a more complex and practical research of manipulator-cranes design is given and ways to implement them on practical level can now be calculated properly. Also, the perspectives of implementation of automated control systems and informational networks on construction sites in order to boost the quality of construction works, safety of labour and ecological safety are shown.

Health physics aspects of advanced reactor licensing reviews

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinson, C.S.

1995-03-01

The last Construction Permit to be issued by the U.S. Nuclear Regulatory Commission (NRC) for a U.S. light water reactor (LWR) was granted in the late 1970s. In 1989 the NRC issued 10 CFR Part 52 which is intended to serve as a framework for the licensing of future reactor designs. The NRC is currently reviewing four different future on {open_quotes}next-generation{close_quotes} reactor designs. Two of these designs are classified as evolutionary designs (modified versions of current generation LWRs) and two are advanced designs (reactors incorporating simplified designs and passive means for accident mitigation). These {open_quotes}next-generation{close_quotes} reactor designs incorporate many innovativemore » design features which are intended to maintain personnel doses ALARA and ensure that the annual average collective dose at these reactors does not exceed 100 person-rems (1 person-sievert) per year. This paper discusses some of the ALARA design features which are incorporated in the four {open_quotes}next-generation{close_quotes} reactor designs incorporate many innovative design features which are intended to maintain personnel doses ALARA and ensure that the annual average collective dose at these reactors does not exceed 100 person-rems (1 person-sievert) per year. This paper discusses some of the ALARA design features which are incorporated in the four {open_quotes}next-generation{close_quotes} reactor designs currently being reviewed by the NRC.« less

Fifteen year performance review of Michigan's European concrete pavement.

DOT National Transportation Integrated Search

2010-02-01

In 1993, a special pavement demonstration project was constructed in Detroit on NB I-75 to evaluate the design features of some highly acclaimed European rigid pavements. The Michigan Department of Transportation (MDOT) and the Federal Highway Admini...

Twenty year performance review of Michigan's European concrete pavement.

DOT National Transportation Integrated Search

2013-10-01

In 1993, a special pavement demonstration project was constructed in Detroit on NB I-75 to evaluate the design features of some highly acclaimed European rigid pavements. The Michigan Department of Transportation (MDOT) and the Federal Highway Admini...

Air convection embankment experimental feature design phase 1

DOT National Transportation Integrated Search

1997-12-01

Prior research work has indicated that air convection embankments are a promising technique for limiting the thaw settlement damage that often occurs when roadway embankments are constructed in regions of warm permafrost. These studies lead to the pr...

Design of converging stepped spillways

USDA-ARS?s Scientific Manuscript database

Roller compacted concrete (RCC) stepped spillways are growing in popularity for providing overtopping protection for aging watershed dams with inadequate auxiliary spillway capacity and for the construction of new dams. Unobtainable land rights, topographic features, and land use changes caused by ...

Design and evaluation of low-cost stainless steel fiberglass foam blades for large wind driven generating systems

NASA Technical Reports Server (NTRS)

Eggert, W. S.

1982-01-01

A low cost wind turbine blade based on a stainless steel fiberglass foam Budd blade design concept, was evaluated for its principle characteristics, low cost features, and its advantages and disadvantages. A blade structure was designed and construction methods and materials were selected. A complete blade tooling concepts, various technical and economic analysis, and evaluations of the blade design were performed. A comprehensive fatigue test program is conducted to provide data to verify the design stress allowables.

Design and evaluation of low-cost stainless steel fiberglass foam blades for large wind driven generating systems

NASA Astrophysics Data System (ADS)

Eggert, W. S.

1982-10-01

A low cost wind turbine blade based on a stainless steel fiberglass foam Budd blade design concept, was evaluated for its principle characteristics, low cost features, and its advantages and disadvantages. A blade structure was designed and construction methods and materials were selected. A complete blade tooling concepts, various technical and economic analysis, and evaluations of the blade design were performed. A comprehensive fatigue test program is conducted to provide data to verify the design stress allowables.

Deep Constrained Siamese Hash Coding Network and Load-Balanced Locality-Sensitive Hashing for Near Duplicate Image Detection.

PubMed

Hu, Weiming; Fan, Yabo; Xing, Junliang; Sun, Liang; Cai, Zhaoquan; Maybank, Stephen

2018-09-01

We construct a new efficient near duplicate image detection method using a hierarchical hash code learning neural network and load-balanced locality-sensitive hashing (LSH) indexing. We propose a deep constrained siamese hash coding neural network combined with deep feature learning. Our neural network is able to extract effective features for near duplicate image detection. The extracted features are used to construct a LSH-based index. We propose a load-balanced LSH method to produce load-balanced buckets in the hashing process. The load-balanced LSH significantly reduces the query time. Based on the proposed load-balanced LSH, we design an effective and feasible algorithm for near duplicate image detection. Extensive experiments on three benchmark data sets demonstrate the effectiveness of our deep siamese hash encoding network and load-balanced LSH.

Design of a Single Motor Based Leg Structure with the Consideration of Inherent Mechanical Stability

NASA Astrophysics Data System (ADS)

Taha Manzoor, Muhammad; Sohail, Umer; Noor-e-Mustafa; Nizami, Muhammad Hamza Asif; Ayaz, Yasar

2017-07-01

The fundamental aspect of designing a legged robot is constructing a leg design that is robust and presents a simple control problem. In this paper, we have successfully designed a robotic leg based on a unique four bar mechanism with only one motor per leg. The leg design parameters used in our platform are extracted from design principles used in biological systems, multiple iterations and previous research findings. These principles guide a robotic leg to have minimal mechanical passive impedance, low leg mass and inertia, a suitable foot trajectory utilizing a practical balance between leg kinematics and robot usage, and the resultant inherent mechanical stability. The designed platform also exhibits the key feature of self-locking. Theoretical tools and software iterations were used to derive these practical features and yield an intuitive sense of the required leg design parameters.

Design and installation of a next generation pilot scale fermentation system.

PubMed

Junker, B; Brix, T; Lester, M; Kardos, P; Adamca, J; Lynch, J; Schmitt, J; Salmon, P

2003-01-01

Four new fermenters were designed and constructed for use in secondary metabolite cultivations, bioconversions, and enzyme production. A new PC/PLC-based control system also was implemented using GE Fanuc PLCs, Genius I/O blocks, and Fix Dynamics SCADA software. These systems were incorporated into an industrial research fermentation pilot plant, designed and constructed in the early 1980s. Details of the design of these new fermenters and the new control system are described and compared with the existing installation for expected effectiveness. In addition, the reasoning behind selection of some of these features has been included. Key to the design was the goal of preserving similarity between the new and previously existing and successfully utilized fermenter hardware and software installations where feasible but implementing improvements where warranted and beneficial. Examples of enhancements include strategic use of Inconel as a material of construction to reduce corrosion, piping layout design for simplified hazardous energy isolation, on-line calculation and control of nutrient feed rates, and the use of field I/O modules located near the vessel to permit low-cost addition of new instrumentation.

Multiple-Objective Optimal Designs for Studying the Dose Response Function and Interesting Dose Levels

PubMed Central

Hyun, Seung Won; Wong, Weng Kee

2016-01-01

We construct an optimal design to simultaneously estimate three common interesting features in a dose-finding trial with possibly different emphasis on each feature. These features are (1) the shape of the dose-response curve, (2) the median effective dose and (3) the minimum effective dose level. A main difficulty of this task is that an optimal design for a single objective may not perform well for other objectives. There are optimal designs for dual objectives in the literature but we were unable to find optimal designs for 3 or more objectives to date with a concrete application. A reason for this is that the approach for finding a dual-objective optimal design does not work well for a 3 or more multiple-objective design problem. We propose a method for finding multiple-objective optimal designs that estimate the three features with user-specified higher efficiencies for the more important objectives. We use the flexible 4-parameter logistic model to illustrate the methodology but our approach is applicable to find multiple-objective optimal designs for other types of objectives and models. We also investigate robustness properties of multiple-objective optimal designs to mis-specification in the nominal parameter values and to a variation in the optimality criterion. We also provide computer code for generating tailor made multiple-objective optimal designs. PMID:26565557

Multiple-Objective Optimal Designs for Studying the Dose Response Function and Interesting Dose Levels.

PubMed

Hyun, Seung Won; Wong, Weng Kee

2015-11-01

We construct an optimal design to simultaneously estimate three common interesting features in a dose-finding trial with possibly different emphasis on each feature. These features are (1) the shape of the dose-response curve, (2) the median effective dose and (3) the minimum effective dose level. A main difficulty of this task is that an optimal design for a single objective may not perform well for other objectives. There are optimal designs for dual objectives in the literature but we were unable to find optimal designs for 3 or more objectives to date with a concrete application. A reason for this is that the approach for finding a dual-objective optimal design does not work well for a 3 or more multiple-objective design problem. We propose a method for finding multiple-objective optimal designs that estimate the three features with user-specified higher efficiencies for the more important objectives. We use the flexible 4-parameter logistic model to illustrate the methodology but our approach is applicable to find multiple-objective optimal designs for other types of objectives and models. We also investigate robustness properties of multiple-objective optimal designs to mis-specification in the nominal parameter values and to a variation in the optimality criterion. We also provide computer code for generating tailor made multiple-objective optimal designs.

Design features of implants for direct skeletal attachment of limb prostheses

PubMed Central

Pitkin, M.

2013-01-01

In direct skeletal attachment (DSA) of limb prostheses, a construct is implanted into an amputee’s residuum bone and protrudes out of the residuum’s skin. This technology represents an alternative to traditional suspension of prostheses via various socket systems, with clear indications when the sockets cannot be properly fitted. Contemporary DSA was invented in the 1990s, and several implant systems have been introduced since then. The current review is intended to compare the design features of implants for DSA whose use in humans or in animal studies has been reported in the literature. PMID:23554122

Accurate prediction of RNA-binding protein residues with two discriminative structural descriptors.

PubMed

Sun, Meijian; Wang, Xia; Zou, Chuanxin; He, Zenghui; Liu, Wei; Li, Honglin

2016-06-07

RNA-binding proteins participate in many important biological processes concerning RNA-mediated gene regulation, and several computational methods have been recently developed to predict the protein-RNA interactions of RNA-binding proteins. Newly developed discriminative descriptors will help to improve the prediction accuracy of these prediction methods and provide further meaningful information for researchers. In this work, we designed two structural features (residue electrostatic surface potential and triplet interface propensity) and according to the statistical and structural analysis of protein-RNA complexes, the two features were powerful for identifying RNA-binding protein residues. Using these two features and other excellent structure- and sequence-based features, a random forest classifier was constructed to predict RNA-binding residues. The area under the receiver operating characteristic curve (AUC) of five-fold cross-validation for our method on training set RBP195 was 0.900, and when applied to the test set RBP68, the prediction accuracy (ACC) was 0.868, and the F-score was 0.631. The good prediction performance of our method revealed that the two newly designed descriptors could be discriminative for inferring protein residues interacting with RNAs. To facilitate the use of our method, a web-server called RNAProSite, which implements the proposed method, was constructed and is freely available at http://lilab.ecust.edu.cn/NABind .

DNA Brick Crystals with Prescribed Depth

PubMed Central

Ke, Yonggang; Ong, Luvena L.; Sun, Wei; Song, Jie; Dong, Mingdong; Shih, William M.; Yin, Peng

2014-01-01

We describe a general framework for constructing two-dimensional crystals with prescribed depth and sophisticated three-dimensional features. These crystals may serve as scaffolds for the precise spatial arrangements of functional materials for diverse applications. The crystals are self-assembled from single-stranded DNA components called DNA bricks. We demonstrate the experimental construction of DNA brick crystals that can grow to micron-size in the lateral dimensions with precisely controlled depth up to 80 nanometers. They can be designed to display user-specified sophisticated three-dimensional nanoscale features, such as continuous or discontinuous cavities and channels, and to pack DNA helices at parallel and perpendicular angles relative to the plane of the crystals. PMID:25343605

Common Characteristics of Good and Poorly Performing PCC Pavements

DOT National Transportation Integrated Search

1998-01-01

This report documents the analysis and findings of a study to identify the site conditions and design/construction features of concrete pavements (JPCP, JRCP, CRCP) that lead to good performance and those that lead to poor performance. Data from Long...

Common Characteristics of Good and Poorly Performing AC Pavements

DOT National Transportation Integrated Search

1999-12-01

This report documents the analysis and findings of a study to identify the site conditions and design/construction features of : flexible pavements that lead to good performance and those that lead to poor performance. Data from the Long Term Pavemen...

FLORIDA LARGE BUILDING STUDY - POLK COUNTY ADMINISTRATION BUILDING

EPA Science Inventory

The report describes an extensive characterization and parameter assessment study of a single, large building in Bartow, FL, with the purpose of assessing the impact on radon entry of design, construction, and operating features of the building, particularly the mechanical subsys...

A School for Complex Needs.

ERIC Educational Resources Information Center

Leisner, Hava

2001-01-01

Presents a case study showing the role specialty materials and finishes play in the design of a school for autistic students. Use of incandescent lighting, muted colors and contrast, and padded flooring are examined as are classroom features and construction challenges encountered. (GR)

21 CFR 211.42 - Design and construction features.

Code of Federal Regulations, 2014 CFR

2014-04-01

... product containers, closures, labeling, in-process materials, or drug products, and to prevent contamination. The flow of components, drug product containers, closures, labeling, in-process materials, and... withholding from use of components, drug product containers, closures, and labeling, pending the appropriate...

21 CFR 211.42 - Design and construction features.

Code of Federal Regulations, 2012 CFR

2012-04-01

... product containers, closures, labeling, in-process materials, or drug products, and to prevent contamination. The flow of components, drug product containers, closures, labeling, in-process materials, and... withholding from use of components, drug product containers, closures, and labeling, pending the appropriate...

21 CFR 211.42 - Design and construction features.

Code of Federal Regulations, 2013 CFR

2013-04-01

... product containers, closures, labeling, in-process materials, or drug products, and to prevent contamination. The flow of components, drug product containers, closures, labeling, in-process materials, and... withholding from use of components, drug product containers, closures, and labeling, pending the appropriate...

21 CFR 211.42 - Design and construction features.

Code of Federal Regulations, 2011 CFR

2011-04-01

... product containers, closures, labeling, in-process materials, or drug products, and to prevent contamination. The flow of components, drug product containers, closures, labeling, in-process materials, and... withholding from use of components, drug product containers, closures, and labeling, pending the appropriate...

Construction of a Learning Environment Supporting Learners' Reflection: A Case of Information Seeking on the Web

ERIC Educational Resources Information Center

Saito, Hitomi; Miwa, Kazuhisa

2007-01-01

In this study, we design a learning environment that supports reflective activities for information seeking on the Web and evaluate its educational effects. The features of this design are: (1) to visualize the learners' search processes as described, based on a cognitive schema, (2) to support two types of reflective activities, such as…

Low-Cost Wood Homes for Rural America - Construction Manual

Treesearch

L.O. Andeson

1969-01-01

Five home designs are described to meet the need for better housing for low-income rural families. Homes feature theintelligent use of wood and wood products as much as possible, are intended for simple and efficient constructionwith typical building labor availableln rural areas, and `are designed to meet.thegoal of a three-bedroom home with at least 1000 square feet...

The thematic structure of passenger comfort experience and its relationship to the context features in the aircraft cabin.

PubMed

Ahmadpour, Naseem; Lindgaard, Gitte; Robert, Jean-Marc; Pownall, Bernard

2014-01-01

This paper describes passenger comfort as an experience generated by the cabin interior features. The findings of previous studies are affirmed regarding a set of 22 context features. Passengers experience a certain level of comfort when these features impact their body and elicit subjective perceptions. New findings characterise these perceptions in the form of eight themes and outline their particular eliciting features. Comfort is depicted as a complex construct derived by passengers' perceptions beyond the psychological (i.e. peace of mind) and physical (i.e. physical well-being) aspects, and includes perceptual (e.g. proxemics) and semantic (e.g. association) aspects. The seat was shown to have a focal role in eliciting seven of those themes and impacting comfort through its diverse characteristics. In a subsequent study, a group of aircraft cabin interior designers highlighted the possibility of employing the eight themes and their eliciting features as a framework for design and evaluation of new aircraft interiors.

Chapter 9: The FTU Machine - Design Construction and Assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pizzuto, A.; Annino, C.; Baldarelli, M.

2004-05-15

The main design features and guidelines for the construction of the 8-T cryogenically cooled Frascati Tokamak Upgrade (FTU) are presented. The main features include the very compact toroidal magnets based on the concept of the 'Bitter' type of coil with wedge-shaped turns, utilized for the first time for the Alcator A and C magnets, and the original configuration of the vacuum vessel (VV) structure, which is fully welded in order to achieve the required high strength and electric resistivity. The present toroidal limiter has been installed following several years of operation, and this installation has required the development of specificmore » remote-handling tools. The toroidal limiter consists of 12 independent sectors made of stainless steel carriers and molybdenum alloy (TZM) tiles. The main fabrication processes developed for the toroidal and poloidal coils as well as for the VV are described. It is to be noted that the assembly procedure has required very accurate machining of all the structures requiring several trials and steps. The machine has shown no problem in operating routinely at its maximum design values (8 T, 1.6 MA)« less

Perspective: Materials Informatics and Big Data: Realization of the Fourth Paradigm of Science in Materials Science

DTIC Science & Technology

2016-08-17

thereby opening up new avenues for accelerated materials discovery and design . The need for such data analytics has also been emphasized by the...and design . The construction of inverse models is typically formulated as an optimiza- tion problem wherein a property or performance metric of...discovery and design . extraction, feature selection, etc. Such data preprocessing can either be supervised or unsupervised, based on whether the

Aplanatic double reflection system for thermophotovoltaic applications: design.

PubMed

Demichelis, F; Ferrari, G; Minetti-Mezzetti, E

1981-12-15

The design of a solar concentrator is presented; it consists of a spherical mirror and a field of Fresnel mirror facets deployed on a spherical surface so that sine condition is satisfied, eliminating both spherical aberration and coma. This particular easy to construct optical system yields high concentration ratios and has the distinct advantage of having a narrow beam aperture near the receiver. These design features make the concentrator particularly suitable for thermophotovoltaic applications.

Dual arm master controller development

NASA Technical Reports Server (NTRS)

Kuban, D. P.; Perkins, G. S.

1985-01-01

The advanced servomanipulator (ASM) slave was designed with an anthropomorphic stance gear/torque tube power drives, and modular construction. These features resulted in increased inertia, friction, and backlash relative to tape driven manipulators. Studies were performed which addressed to human factor design and performance tradeoffs associated with the corresponding master controller best suited for the ASM. The results of these studies, as well as the conceptual design of the dual arm master controller, are presented.

Rural Design Ethics Based on Four Dimensions

NASA Astrophysics Data System (ADS)

Zhang, Jiaxin; Zhu, Li

2017-12-01

China has a large rural area with a large population, whose architectural features, natural landscape, organizational structure and industrial structure are very different from that of cities. In the past, the contradictory between city and rural areas in China had negative effects on rural construction, resulting in a slow development. The excessive focus on city design has led to the neglect of rural design. Blindly using the concept and method of city design to renewed the countryside is a kind of destruction to the countryside, and also wastes a lot of construction resources. Design is influenced by ethical concepts, which needs to pay more attention to the culture tendency and society. Urban design makes theoretical investigation aiming at the ethical questions that emerged from city, then summarizes the design strategies of the city. While Chinese rural design has only begun to enter people’s horizon, and there is very little discussion about it. Due to the lack of ethical value guidance, Chinese rural design and construction has many problems at different levels of ecology, culture and industry. Therefore this paper primarily explores the domestic and foreign design ethics, attempting to provide a new perspective for Chinese rural design, aiming at finding a realistic and forward-looking solution for Chinese rural design concerning to the complex relation between city and rural areas.

Incipient Fault Detection for Rolling Element Bearings under Varying Speed Conditions.

PubMed

Xue, Lang; Li, Naipeng; Lei, Yaguo; Li, Ningbo

2017-06-20

Varying speed conditions bring a huge challenge to incipient fault detection of rolling element bearings because both the change of speed and faults could lead to the amplitude fluctuation of vibration signals. Effective detection methods need to be developed to eliminate the influence of speed variation. This paper proposes an incipient fault detection method for bearings under varying speed conditions. Firstly, relative residual (RR) features are extracted, which are insensitive to the varying speed conditions and are able to reflect the degradation trend of bearings. Then, a health indicator named selected negative log-likelihood probability (SNLLP) is constructed to fuse a feature set including RR features and non-dimensional features. Finally, based on the constructed SNLLP health indicator, a novel alarm trigger mechanism is designed to detect the incipient fault. The proposed method is demonstrated using vibration signals from bearing tests and industrial wind turbines. The results verify the effectiveness of the proposed method for incipient fault detection of rolling element bearings under varying speed conditions.

Incipient Fault Detection for Rolling Element Bearings under Varying Speed Conditions

PubMed Central

Xue, Lang; Li, Naipeng; Lei, Yaguo; Li, Ningbo

2017-01-01

Varying speed conditions bring a huge challenge to incipient fault detection of rolling element bearings because both the change of speed and faults could lead to the amplitude fluctuation of vibration signals. Effective detection methods need to be developed to eliminate the influence of speed variation. This paper proposes an incipient fault detection method for bearings under varying speed conditions. Firstly, relative residual (RR) features are extracted, which are insensitive to the varying speed conditions and are able to reflect the degradation trend of bearings. Then, a health indicator named selected negative log-likelihood probability (SNLLP) is constructed to fuse a feature set including RR features and non-dimensional features. Finally, based on the constructed SNLLP health indicator, a novel alarm trigger mechanism is designed to detect the incipient fault. The proposed method is demonstrated using vibration signals from bearing tests and industrial wind turbines. The results verify the effectiveness of the proposed method for incipient fault detection of rolling element bearings under varying speed conditions. PMID:28773035

Principles and concepts in designing tropical-shore settlement in estuary ecosystem, case study: Weriagar District, Bintuni Bay

NASA Astrophysics Data System (ADS)

Firmansyah; Nidia Kusuma, Bintang; Prayuni, Ira; Fernando, Aldo

2017-12-01

Weriagar District is located in estuary area and is prone to land loss, due to river and coastal erosion. This paper will describe about tropical-shore settlement design and house design in estuary area. The results from analysis phase shows that it's necessary to design a house and settlement that can fulfil the needs of indigenous people, both functionally and aesthetically. Functionally, the house is designed to provide spaces for both private and public needs of the family. It can be used either as a family private space or as a public gathering space between family and their neighbours. Aesthetically, house’ architectural form is designed into that identifies the locality of Weriagar District. The houses’ design feature highlighted in using local material, rainwater harvesting system, high pitched roof feature as response to hot-humid climate, and elevated-floor feature as response to tidal condition in estuary area. The houses design also considered daily activity pattern and community culture, including appropriate structure, construction, and material availability. The expected result was that the settlement improvement and house design would meet suitable standards and needs of inhabitants in Weriagar District.

Design and grayscale fabrication of beamfanners in a silicon substrate

NASA Astrophysics Data System (ADS)

Ellis, Arthur Cecil

2001-11-01

This dissertation addresses important first steps in the development of a grayscale fabrication process for multiple phase diffractive optical elements (DOS's) in silicon. Specifically, this process was developed through the design, fabrication, and testing of 1-2 and 1-4 beamfanner arrays for 5-micron illumination. The 1-2 beamfanner arrays serve as a test-of- concept and basic developmental step toward the construction of the 1-4 beamfanners. The beamfanners are 50 microns wide, and have features with dimensions of between 2 and 10 microns. The Iterative Annular Spectrum Approach (IASA) method, developed by Steve Mellin of UAH, and the Boundary Element Method (BEM) are the design and testing tools used to create the beamfanner profiles and predict their performance. Fabrication of the beamfanners required the techniques of grayscale photolithography and reactive ion etching (RIE). A 2-3micron feature size 1-4 silicon beamfanner array was fabricated, but the small features and contact photolithographic techniques available prevented its construction to specifications. A second and more successful attempt was made in which both 1-4 and 1-2 beamfanner arrays were fabricated with a 5-micron minimum feature size. Photolithography for the UAH array was contracted to MEMS-Optical of Huntsville, Alabama. A repeatability study was performed, using statistical techniques, of 14 photoresist arrays and the subsequent RIE process used to etch the arrays in silicon. The variance in selectivity between the 14 processes was far greater than the variance between the individual etched features within each process. Specifically, the ratio of the variance of the selectivities averaged over each of the 14 etch processes to the variance of individual feature selectivities within the processes yielded a significance level below 0.1% by F-test, indicating that good etch-to-etch process repeatability was not attained. One of the 14 arrays had feature etch-depths close enough to design specifications for optical testing, but 5- micron IR illumination of the 1-4 and 1-2 beamfanners yielded no convincing results of beam splitting in the detector plane 340 microns from the surface of the beamfanner array.

National Program for Inspection of Non-Federal Dams. Collins Company Upper Dam (CT 00674), Connecticut River Basin, Canton, Connecticut. Phase I Inspection Report.

DTIC Science & Technology

1979-07-01

Engineering Division p 0 CAR WE H FRZIAN, NENBER Design Branch Engineering Division J SEPE FIN~EGAN, JR.,CIV ater Control Branch * Engineering Division...Operator g. Purpose of Dam h. Design and Construction History i. Normal Operational Procedures 1.3 PERTINENT DATA ........................... 4 a...Tunnel i. Spillways j. Regulating Outlets SECTION 2: ENGINEERING DATA 2.1 DESIGN .............................. 9 a. Available Data b. Design Features c

Framework for Flux Qubit Design

NASA Astrophysics Data System (ADS)

Yan, Fei; Kamal, Archana; Krantz, Philip; Campbell, Daniel; Kim, David; Yoder, Jonilyn; Orlando, Terry; Gustavsson, Simon; Oliver, William; Engineering Quantum Systems Team

A qubit design for higher performance relies on the understanding of how various qubit properties are related to design parameters. We construct a framework for understanding the qubit design in the flux regime. We explore different parameter regimes, looking for features desirable for certain purpose in the context of quantum computing. This research was funded by the Office of the Director of National Intelligence (ODNI), Intelligence Advanced Research Projects Activity (IARPA) via MIT Lincoln Laboratory under Air Force Contract No. FA8721-05-C-0002.

A Study on the Rural Residence in the Northern Area of Zhejiang Province from the Perspective of Green Living Environment

NASA Astrophysics Data System (ADS)

Wang, J.; Gao, W. J.; Wang, C.

2018-05-01

At present, owing to the rapid development of rural construction, it lacks corresponding theories and practices and damages to the features of rural area, ignoring the geography, suitability and green living environment factors. The research selects rural residence as the object, defining “courtyard” as the basic unit for rural residence. It utilizes the principle of topology as the expanding media, by the method of principle of cellular structure and green living environment design strategy. The essay establishes the design and construction system of “rural basic unit”, combining functions and structures, prototype menu, chamber space and compound interface, from the perspective of green living environment. It aims to guide rural construction and protect the ruralliving environment.

How to make a good animation: A grounded cognition model of how visual representation design affects the construction of abstract physics knowledge

NASA Astrophysics Data System (ADS)

Chen, Zhongzhou; Gladding, Gary

2014-06-01

Visual representations play a critical role in teaching physics. However, since we do not have a satisfactory understanding of how visual perception impacts the construction of abstract knowledge, most visual representations used in instructions are either created based on existing conventions or designed according to the instructor's intuition, which leads to a significant variance in their effectiveness. In this paper we propose a cognitive mechanism based on grounded cognition, suggesting that visual perception affects understanding by activating "perceptual symbols": the basic cognitive unit used by the brain to construct a concept. A good visual representation activates perceptual symbols that are essential for the construction of the represented concept, whereas a bad representation does the opposite. As a proof of concept, we conducted a clinical experiment in which participants received three different versions of a multimedia tutorial teaching the integral expression of electric potential. The three versions were only different by the details of the visual representation design, only one of which contained perceptual features that activate perceptual symbols essential for constructing the idea of "accumulation." On a following post-test, participants receiving this version of tutorial significantly outperformed those who received the other two versions of tutorials designed to mimic conventional visual representations used in classrooms.

Analysis of a mammography teaching program based on an affordance design model.

PubMed

Luo, Ping; Eikman, Edward A; Kealy, William; Qian, Wei

2006-12-01

The wide use of computer technology in education, particularly in mammogram reading, asks for e-learning evaluation. The existing media comparative studies, learner attitude evaluations, and performance tests are problematic. Based on an affordance design model, this study examined an existing e-learning program on mammogram reading. The selection criteria include content relatedness, representativeness, e-learning orientation, image quality, program completeness, and accessibility. A case study was conducted to examine the affordance features, functions, and presentations of the selected software. Data collection and analysis methods include interviews, protocol-based document analysis, and usability tests and inspection. Also some statistics were calculated. The examination of PBE identified that this educational software designed and programmed some tools. The learner can use these tools in the process of optimizing displays, scanning images, comparing different projections, marking the region of interests, constructing a descriptive report, assessing one's learning outcomes, and comparing one's decisions with the experts' decisions. Further, PBE provides some resources for the learner to construct one's knowledge and skills, including a categorized image library, a term-searching function, and some teaching links. Besides, users found it easy to navigate and carry out tasks. The users also reacted positively toward PBE's navigation system, instructional aids, layout, pace and flow of information, graphics, and other presentation design. The software provides learners with some cognitive tools, supporting their perceptual problem-solving processes and extending their capabilities. Learners can internalize the mental models in mammogram reading through multiple perceptual triangulations, sensitization of related features, semantic description of mammogram findings, and expert-guided semantic report construction. The design of these cognitive tools and the software interface matches the findings and principles in human learning and instructional design. Working with PBE's case-based simulations and categorized gallery, learners can enrich and transfer their experience to their jobs.

Anthropometric and biomechanical characteristics on body segments of Koreans.

PubMed

Park, S J; Kim, C B; Park, S C

1999-05-01

This paper documents the physical measurements of the Korean population in order to construct a data base for ergonomic design. The dimension, volume, density, mass, and center of mass of Koreans whose ages range from 7 to 49 were investigated. Sixty-five male subjects and sixty-nine female subjects participated. Eight body segments (head with neck, trunk, thigh, shank, foot, upper arm, forearm and hand) were directly measured with a Martin-type anthropometer, and the immersion method was adopted to measure the volume of body segments. After this, densities were computed by the density equations in Drillis and Contini (1966). The reaction board method was employed for the measurement of the center of mass. Obtained data were compared with the results in the literature. The results in this paper showed different features on body segment parameters comparing with the results in the literature. The constructed data base can be applied to statistical guideline for product design, workspace design, design of clothing and tools, furniture design and construction of biomechanical models for Korean. Also, they can be extended to the application areas for Mongolian.

Thermal-depth matching in dynamic scene based on affine projection and feature registration

NASA Astrophysics Data System (ADS)

Wang, Hongyu; Jia, Tong; Wu, Chengdong; Li, Yongqiang

2018-03-01

This paper aims to study the construction of 3D temperature distribution reconstruction system based on depth and thermal infrared information. Initially, a traditional calibration method cannot be directly used, because the depth and thermal infrared camera is not sensitive to the color calibration board. Therefore, this paper aims to design a depth and thermal infrared camera calibration board to complete the calibration of the depth and thermal infrared camera. Meanwhile a local feature descriptors in thermal and depth images is proposed. The belief propagation matching algorithm is also investigated based on the space affine transformation matching and local feature matching. The 3D temperature distribution model is built based on the matching of 3D point cloud and 2D thermal infrared information. Experimental results show that the method can accurately construct the 3D temperature distribution model, and has strong robustness.

WebQuests: a new instructional strategy for nursing education.

PubMed

Lahaie, Ulysses

2007-01-01

A WebQuest is a model or framework for designing effective Web-based instructional strategies featuring inquiry-oriented activities. It is an innovative approach to learning that is enhanced by the use of evolving instructional technology. WebQuests have invigorated the primary school (grades K through 12) educational sector around the globe, yet there is sparse evidence in the literature of WebQuests at the college and university levels. WebQuests are congruent with pedagogical approaches and cognitive activities commonly used in nursing education. They are simple to construct using a step-by-step approach, and nurse educators will find many related resources on the Internet to help them get started. Included in this article are a discussion of the critical attributes and main features of WebQuests, construction tips, recommended Web sites featuring essential resources, a discussion of WebQuest-related issues identified in the literature, and some suggestions for further research.

Towards Universal Design Hotels in Denmark.

PubMed

Grangaard, Sidse

2016-01-01

Based on the research project 'Accessible Hotel Rooms' that studies the balance between the experience of supply and demand regarding accessibility features in Danish hotel rooms, this paper demonstrates factors having an influence on Universal Design hotels in Denmark. The research project was financed by the Danish Transport and Construction Agency. Different notions in the hotel sector of the current supply and demand for Universal Design hotel rooms are identified, as well as future demand. Despite supplying accessible rooms, some hotels do not advertise their accessibility features on their website. There exists an attitude in the hotel sector that functions as a barrier for Universal Design: if there are enough guests, for example business travellers, then why market the hotel on Universal Design? The paper points out the coherence between the understanding of the users and the view of demand. Another important factor is Corporate Social Responsibility, which can be regarded as a strategy or platform towards Universal Design hotels.

In Silico Syndrome Prediction for Coronary Artery Disease in Traditional Chinese Medicine

PubMed Central

Lu, Peng; Chen, Jianxin; Zhao, Huihui; Gao, Yibo; Luo, Liangtao; Zuo, Xiaohan; Shi, Qi; Yang, Yiping; Yi, Jianqiang; Wang, Wei

2012-01-01

Coronary artery disease (CAD) is the leading causes of deaths in the world. The differentiation of syndrome (ZHENG) is the criterion of diagnosis and therapeutic in TCM. Therefore, syndrome prediction in silico can be improving the performance of treatment. In this paper, we present a Bayesian network framework to construct a high-confidence syndrome predictor based on the optimum subset, that is, collected by Support Vector Machine (SVM) feature selection. Syndrome of CAD can be divided into asthenia and sthenia syndromes. According to the hierarchical characteristics of syndrome, we firstly label every case three types of syndrome (asthenia, sthenia, or both) to solve several syndromes with some patients. On basis of the three syndromes' classes, we design SVM feature selection to achieve the optimum symptom subset and compare this subset with Markov blanket feature select using ROC. Using this subset, the six predictors of CAD's syndrome are constructed by the Bayesian network technique. We also design Naïve Bayes, C4.5 Logistic, Radial basis function (RBF) network compared with Bayesian network. In a conclusion, the Bayesian network method based on the optimum symptoms shows a practical method to predict six syndromes of CAD in TCM. PMID:22567030

A 1-2 GHz pulsed and continuous wave electron paramagnetic resonance spectrometer

NASA Astrophysics Data System (ADS)

Quine, Richard W.; Rinard, George A.; Ghim, Barnard T.; Eaton, Sandra S.; Eaton, Gareth R.

1996-07-01

A microwave bridge has been constructed that performs three types of electron paramagnetic resonance experiments: continuous wave, pulsed saturation recovery, and pulsed electron spin echo. Switching between experiment types can be accomplished via front-panel switches without moving the sample. Design features and performance of the bridge and of a resonator used in testing the bridge are described. The bridge is constructed of coaxial components connected with semirigid cable. Particular attention has been paid to low-noise design of the preamplifier and stability of automatic frequency control circuits. The bridge incorporates a Smith chart display and phase adjustment meter for ease of tuning.

Scientific Opportunities and Plans for FRIB

NASA Astrophysics Data System (ADS)

Bollen, Georg

2014-09-01

FRIB, the US's ``Facility for Rare Isotope Beams'' under construction at Michigan State University will be a world-leading rare isotope beam facility. FRIB will be based on a 400 kW, 200 MeV/u heavy ion linac and provide a wide variety of high-quality beams of unstable isotopes at unprecedented intensities, opening exciting research perspectives with fast, stopped, and reaccelerated beams. This talk will summarize the scientific opportunities with FRIB in the areas of nuclear science, nuclear astrophysics, and the test of fundamental interaction and symmetries, as well using isotopes from FRIB for societal benefits. Design features of FRIB and the status of the ongoing construction will be presented. FRIB, the US's ``Facility for Rare Isotope Beams'' under construction at Michigan State University will be a world-leading rare isotope beam facility. FRIB will be based on a 400 kW, 200 MeV/u heavy ion linac and provide a wide variety of high-quality beams of unstable isotopes at unprecedented intensities, opening exciting research perspectives with fast, stopped, and reaccelerated beams. This talk will summarize the scientific opportunities with FRIB in the areas of nuclear science, nuclear astrophysics, and the test of fundamental interaction and symmetries, as well using isotopes from FRIB for societal benefits. Design features of FRIB and the status of the ongoing construction will be presented. This material is based upon work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661, the State of Michigan and Michigan State University. Michigan State University designs and establishes FRIB as a DOE.

The quality estimation of exterior wall’s and window filling’s construction design

NASA Astrophysics Data System (ADS)

Saltykov, Ivan; Bovsunovskaya, Maria

2017-10-01

The article reveals the term of “artificial envelope” in dwelling building. Authors offer a complex multifactorial approach to the design quality estimation of external fencing structures, which is based on various parameters impact. These referred parameters are: functional, exploitation, cost, and also, the environmental index is among them. The quality design index Qк is inputting for the complex characteristic of observed above parameters. The mathematical relation of this index from these parameters is the target function for the quality design estimation. For instance, the article shows the search of optimal variant for wall and window designs in small, middle and large square dwelling premises of economic class buildings. The graphs of target function single parameters are expressed for the three types of residual chamber’s dimensions. As a result of the showing example, there is a choice of window opening’s dimensions, which make the wall’s and window’s constructions properly correspondent to the producible complex requirements. The authors reveal the comparison of recommended window filling’s square in accordance with the building standards, and the square, due to the finding of the optimal variant of the design quality index. The multifactorial approach for optimal design searching, which is mentioned in this article, can be used in consideration of various construction elements of dwelling buildings in accounting of suitable climate, social and economic construction area features.

Conceptual design and analysis of roads and road construction machinery for initial lunar base operations

NASA Technical Reports Server (NTRS)

Sines, Jeffrey L.; Banks, Joel; Efatpenah, Keyanoush

1990-01-01

Recent developments have made it possible for scientists and engineers to consider returning to the Moon to build a manned lunar base. The base can be used to conduct scientific research, develop new space technology, and utilize the natural resources of the Moon. Areas of the base will be separated, connected by a system of roads that reduce the power requirements of vehicles traveling on them. Feasible road types for the lunar surface were analyzed and a road construction system was designed for initial lunar base operations. A model was also constructed to show the system configuration and key operating features. The alternate designs for the lunar road construction system were developed in four stages: analyze and select a road type; determine operations and machinery needed to produce the road; develop machinery configurations; and develop alternates for several machine components. A compacted lunar soil road was selected for initial lunar base operations. The only machinery required to produce this road were a grader and a compactor. The road construction system consists of a main drive unit which is used for propulsion, a detachable grader assembly, and a towed compactor.

Conoco's new approach to drill site construction in difficult, remote, swamp and jungle terrain Irian Jaya, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roodriguez, F.H.

1984-02-01

In October 1982, Conoco Irian Jaya as operator: and partners: Pertamina, Inpex Bintuni Limited, and Moeco Irian Jaya Company, mobilized construction equipment from Singapore to the KBS ''A'' contract area in Irian Jaya, Indonesia for the purpose of constructing a base camp and drill three exploratory sites. What made this construction effort different from others previously used in Irian Jaya; was that it incorporated several new and unique features, namely: a turnkey approach to construction; that is Conoco providing complete set of specifications and conditions with contractor assuming risks for a lump sum payment; special equipment designed by contractor formore » Irian Jaya operations; an incentive to co pensate or penalize contractor for helicopter hours flown below or above a predetermined number; structural steel pile platform designs for two swamp locations (Ayot and Aum), as opposed to the more conventional corduroy timber log-plank arrangement; and drilling rig pads designed for specific heli-rig with limited extra space. All work was successfully completed within the time frame stipulated in the contract, that is five months from the time the contractor was notified to begin mobilization of equipment, materials and personnel.« less

Developing a habitat-driven approach to CWWT design

USGS Publications Warehouse

Sartoris, James J.; Thullen, Joan S.

1998-01-01

A habitat-driven approach to CWWT design is defined as designing the constructed wetland to maximize habitat values for a given site within the constraints of meeting specified treatment criteria. This is in contrast to the more typical approach of designing the CWWT to maximize treatment efficiency, and then, perhaps, adding wildlife habitat features. The habitat-driven approach is advocated for two reasons: (1) because good wetland habitat is critically lacking, and (2) because it is hypothesized that well-designed habitat will result in good, sustainable wastewater treatment.

Multi-sensor image registration based on algebraic projective invariants.

PubMed

Li, Bin; Wang, Wei; Ye, Hao

2013-04-22

A new automatic feature-based registration algorithm is presented for multi-sensor images with projective deformation. Contours are firstly extracted from both reference and sensed images as basic features in the proposed method. Since it is difficult to design a projective-invariant descriptor from the contour information directly, a new feature named Five Sequential Corners (FSC) is constructed based on the corners detected from the extracted contours. By introducing algebraic projective invariants, we design a descriptor for each FSC that is ensured to be robust against projective deformation. Further, no gray scale related information is required in calculating the descriptor, thus it is also robust against the gray scale discrepancy between the multi-sensor image pairs. Experimental results utilizing real image pairs are presented to show the merits of the proposed registration method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Stephenson, R.

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta-based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA, in the mixed humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach to potential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STARmore » requirements, and a high performance heating and cooling system. Construction quality and execution was a high priority for TaC Studios and was ensured by a third party review process. Post-construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowners wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this home was evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored to determine their impact on overall energy consumption.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Stephenson, R.

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta-based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA in the mixed humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach topotential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STAR requirements,more » and a high performance heating and cooling system. Construction quality and execution was a high priority for TaCStudios and was ensured by a third party review process. Post-construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowners wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this homewas evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored todetermine their impact on overall energy consumption.« less

Evaluation of a metal fuselage frame selectively reinforced with filamentary composites for space shuttle application

NASA Technical Reports Server (NTRS)

Oken, S.; Skoumal, D. E.; Straayer, J. W.

1974-01-01

The development of metal structures reinforced with filamentary composites as a weight saving feature of the space shuttle components is discussed. A frame was selected for study that was representative of the type of construction used in the bulk frames of the orbiter vehicle. Theoretical and experimental investigations were conducted. Component tests were performed to evaluate the critical details used in the designs and to provide credibility to the weight saving results. A model frame was constructed of the reinforced metal material to provide a final evaluation of the construction under realistic load conditions.

The “shape” and “meaning” of the roof arts in Chinese classical architecture

NASA Astrophysics Data System (ADS)

Li, Xianda; liu, Yu

2017-04-01

This paper takes the “roof” in Chinese classical architecture as the research object. The breakthrough point of this paper would be the perspective of design aesthetics. Through the rational and perceptual analysis of the roof art, this paper would reveal that the roof shape has the double artistic features: “beauty of shape” and “beauty of idea”. This paper would have a comprehensive analysis for the following aspects: the rational method of roof construction, the emotional feeling of the roof construction and the implied meaning of beauty in the roof construction.

Gene Composer: database software for protein construct design, codon engineering, and gene synthesis

PubMed Central

Lorimer, Don; Raymond, Amy; Walchli, John; Mixon, Mark; Barrow, Adrienne; Wallace, Ellen; Grice, Rena; Burgin, Alex; Stewart, Lance

2009-01-01

Background To improve efficiency in high throughput protein structure determination, we have developed a database software package, Gene Composer, which facilitates the information-rich design of protein constructs and their codon engineered synthetic gene sequences. With its modular workflow design and numerous graphical user interfaces, Gene Composer enables researchers to perform all common bio-informatics steps used in modern structure guided protein engineering and synthetic gene engineering. Results An interactive Alignment Viewer allows the researcher to simultaneously visualize sequence conservation in the context of known protein secondary structure, ligand contacts, water contacts, crystal contacts, B-factors, solvent accessible area, residue property type and several other useful property views. The Construct Design Module enables the facile design of novel protein constructs with altered N- and C-termini, internal insertions or deletions, point mutations, and desired affinity tags. The modifications can be combined and permuted into multiple protein constructs, and then virtually cloned in silico into defined expression vectors. The Gene Design Module uses a protein-to-gene algorithm that automates the back-translation of a protein amino acid sequence into a codon engineered nucleic acid gene sequence according to a selected codon usage table with minimal codon usage threshold, defined G:C% content, and desired sequence features achieved through synonymous codon selection that is optimized for the intended expression system. The gene-to-oligo algorithm of the Gene Design Module plans out all of the required overlapping oligonucleotides and mutagenic primers needed to synthesize the desired gene constructs by PCR, and for physically cloning them into selected vectors by the most popular subcloning strategies. Conclusion We present a complete description of Gene Composer functionality, and an efficient PCR-based synthetic gene assembly procedure with mis-match specific endonuclease error correction in combination with PIPE cloning. In a sister manuscript we present data on how Gene Composer designed genes and protein constructs can result in improved protein production for structural studies. PMID:19383142

Gene composer: database software for protein construct design, codon engineering, and gene synthesis.

PubMed

Lorimer, Don; Raymond, Amy; Walchli, John; Mixon, Mark; Barrow, Adrienne; Wallace, Ellen; Grice, Rena; Burgin, Alex; Stewart, Lance

2009-04-21

To improve efficiency in high throughput protein structure determination, we have developed a database software package, Gene Composer, which facilitates the information-rich design of protein constructs and their codon engineered synthetic gene sequences. With its modular workflow design and numerous graphical user interfaces, Gene Composer enables researchers to perform all common bio-informatics steps used in modern structure guided protein engineering and synthetic gene engineering. An interactive Alignment Viewer allows the researcher to simultaneously visualize sequence conservation in the context of known protein secondary structure, ligand contacts, water contacts, crystal contacts, B-factors, solvent accessible area, residue property type and several other useful property views. The Construct Design Module enables the facile design of novel protein constructs with altered N- and C-termini, internal insertions or deletions, point mutations, and desired affinity tags. The modifications can be combined and permuted into multiple protein constructs, and then virtually cloned in silico into defined expression vectors. The Gene Design Module uses a protein-to-gene algorithm that automates the back-translation of a protein amino acid sequence into a codon engineered nucleic acid gene sequence according to a selected codon usage table with minimal codon usage threshold, defined G:C% content, and desired sequence features achieved through synonymous codon selection that is optimized for the intended expression system. The gene-to-oligo algorithm of the Gene Design Module plans out all of the required overlapping oligonucleotides and mutagenic primers needed to synthesize the desired gene constructs by PCR, and for physically cloning them into selected vectors by the most popular subcloning strategies. We present a complete description of Gene Composer functionality, and an efficient PCR-based synthetic gene assembly procedure with mis-match specific endonuclease error correction in combination with PIPE cloning. In a sister manuscript we present data on how Gene Composer designed genes and protein constructs can result in improved protein production for structural studies.

SERDP and ESTCP Expert Panel Workshop on Research and Development Needs for the Environmental Remediation Application of Molecular Biological Tools

DTIC Science & Technology

2005-10-01

used to infer metabolic rates in marine systems. For example, there is evidence from both pure cultures and environmental samples that rbcL...It includes many useful bioinformatics features such as constructing a neighbor-joining tree for a subset of sequences, downloading a subset of...further provide software that allow users to extract useful information from sequences. The most commonly used feature is probe/primer design

Software for math and science education for the deaf.

PubMed

Adamo-Villani, Nicoletta; Wilbur, Ronnie

2010-01-01

In this article, we describe the development of two novel approaches to teaching math and science concepts to deaf children using 3D animated interactive software. One approach, Mathsigner, is non-immersive and the other, SMILE, is a virtual reality immersive environment. The content is curriculum-based, and the animated signing characters are constructed with state-of-the art technology and design. We report preliminary development findings of usability and appeal based on programme features (e.g. 2D/3D, immersiveness, interaction type, avatar and interface design) and subject features (hearing status, gender and age). Programme features of 2D/3D, immersiveness and interaction type were very much affected by subject features. Among subject features, we find significant effects of hearing status (deaf children take longer time and make more mistakes than hearing children) and gender (girls take longer than boys; girls prefer immersive environments rather than desktop presentation; girls are more interested in content than technology compared to boys). For avatar type, we found a preference for seamless, deformable characters over segmented ones. For interface comparisons, there were no subject effects, but an animated interface resulted in reduced time to task completion compared to static interfaces with and without sound and highlighting. These findings identify numerous features that affect software design and appeal and suggest that designers must be careful in their assumptions during programme development.

7 CFR 1924.108 - Grading and drainage.

Code of Federal Regulations, 2014 CFR

2014-01-01

... exposed for long periods during construction. (d) Storm water systems. The design of storm water systems... basin level. Storm water systems should be compatible with the natural features of the site. In areas with inadequate drainage systems, permanent or temporary storm water storage shall be an integral part...

7 CFR 1924.108 - Grading and drainage.

Code of Federal Regulations, 2011 CFR

2011-01-01

... exposed for long periods during construction. (d) Storm water systems. The design of storm water systems... basin level. Storm water systems should be compatible with the natural features of the site. In areas with inadequate drainage systems, permanent or temporary storm water storage shall be an integral part...

7 CFR 1924.108 - Grading and drainage.

Code of Federal Regulations, 2010 CFR

2010-01-01

... exposed for long periods during construction. (d) Storm water systems. The design of storm water systems... basin level. Storm water systems should be compatible with the natural features of the site. In areas with inadequate drainage systems, permanent or temporary storm water storage shall be an integral part...

7 CFR 1924.108 - Grading and drainage.

Code of Federal Regulations, 2013 CFR

2013-01-01

... exposed for long periods during construction. (d) Storm water systems. The design of storm water systems... basin level. Storm water systems should be compatible with the natural features of the site. In areas with inadequate drainage systems, permanent or temporary storm water storage shall be an integral part...

7 CFR 1924.108 - Grading and drainage.

Code of Federal Regulations, 2012 CFR

2012-01-01

... exposed for long periods during construction. (d) Storm water systems. The design of storm water systems... basin level. Storm water systems should be compatible with the natural features of the site. In areas with inadequate drainage systems, permanent or temporary storm water storage shall be an integral part...

Detonation Jet Engine. Part 2--Construction Features

ERIC Educational Resources Information Center

Bulat, Pavel V.; Volkov, Konstantin N.

2016-01-01

We present the most relevant works on jet engine design that utilize thermodynamic cycle of detonative combustion. Detonation engines of various concepts, pulse detonation, rotational and engine with stationary detonation wave, are reviewed. Main trends in detonation engine development are discussed. The most important works that carried out…

An analytic-numerical method for the construction of the reference law of operation for a class of mechanical controlled systems

NASA Astrophysics Data System (ADS)

Mizhidon, A. D.; Mizhidon, K. A.

2017-04-01

An analytic-numerical method for the construction of a reference law of operation for a class of dynamic systems describing vibrations in controlled mechanical systems is proposed. By the reference law of operation of a system, we mean a law of the system motion that satisfies all the requirements for the quality and design features of the system under permanent external disturbances. As disturbances, we consider polyharmonic functions with known amplitudes and frequencies of the harmonics but unknown initial phases. For constructing the reference law of motion, an auxiliary optimal control problem is solved in which the cost function depends on a weighting coefficient. The choice of the weighting coefficient ensures the design of the reference law. Theoretical foundations of the proposed method are given.

Semi-Degradable Scaffold for Articular Cartilage Replacement

PubMed Central

Charlton, DC; Peterson, MGE; Spiller, K; Lowman, A; Torzilli, PA; Maher, SA

2009-01-01

The challenge of designing a construct for the repair of focal cartilage defects such that it mimics the mechanical properties of and can integrate with native cartilage has not been met by existing technologies. Herein we describe a novel construct consisting of a non-degradable poly-vinyl alcohol scaffold to provide long-term mechanical stability, interconnected pores to allow for the infiltration of chondrocytes and poly-lactic glycolic acid microspheres for the incorporation of growth factors to enhance cellular migration. The objective of this study was to characterize the morphological features and mechanical properties of our porous PVA-PLGA construct as a function of PLGA content. Varying the PLGA content was found to have a significant effect on the morphological features of the construct. As PLGA content increased from 10 – 75%, samples exhibited a six-fold increase in average percent porosity, an increase in average microsphere diameter from 8 – 34 µm, and an increase in average pore diameter from 29 – 111 µm. The effect of PLGA content on Aggregate Modulus and Permeability was less profound. Our findings suggest that that morphology of the construct can be tailored to optimize cellular infiltration and the dynamic mechanical response. PMID:18333818

Design, Fabrication, and Performance of Foil Gas Thrust Bearings for Microturbomachinery Applications

NASA Technical Reports Server (NTRS)

Dykas, Brian; Bruckner, Robert; DellaCorte, Christopher; Edmonds, Brian; Prahl, Joseph

2008-01-01

A methodology for the design and construction of simple foil thrust bearings intended for parametric performance testing and low marginal costs is presented. Features drawn from a review of the open literature are discussed as they relate to bearing performance. The design of fixtures and tooling required to fabricate foil thrust bearings is presented, using conventional machining processes where possible. A prototype bearing with dimensions drawn from the literature is constructed, with all fabrication steps described. A load-deflection curve for the bearing is presented to illustrate structural stiffness characteristics. Start-top cycles are performed on the bearing at a temperature of 425 C to demonstrate early-life wear patterns. A test of bearing load capacity demonstrates useful performance when compared with data obtained from the open literature.

Specific features of modern multifunctional high-rise building construction

NASA Astrophysics Data System (ADS)

Manukhina, Lyubov; Samosudova, Natal'ja

2018-03-01

The article analyzes the main reasons for the development of high-rise building construction the most important of which-is a limitation of the urban areas and, consequently, the high price of land reserved for construction. New engineering and compositional solutions for the creation of new types of buildings are considered - complex technical designs of a large number of storeys completely meet the new requirements for safety and comfort. Some peculiarities of designing high-rise buildings and searching for optimal architectural and planning solutions are revealed since, with external architectural simplicity, high-rise buildings have complex structural and technological and space-planning solutions. We consider the specific features of a high-rise housing in various countries around the world, including Russia, such as the layout of the multi-storey residential buildings, depending on the climatic characteristics of the regions, assessment of the geological risk of the construction site, the choice of parameters and functional purpose of the sections of the territory of high-rise construction, location of the town-planning object for substantiating the overall dimensions of the building, assessment of changes aeration and engineering and hydrological conditions of the site. A special place in the article on the problems of improvement of the territory, the device of courtyards, landscaping, the device of playing and sports grounds. The main conclusion in the article is the following problem - when developing high-rise housing construction, the development of high-rise housing, and an increase in the population density in the territory of large cities of Russia, necessary to create a comfortable and safe level of residents living and not a decrease, but an improvement in the quality of the urban environment.

Modelling robot construction systems

NASA Technical Reports Server (NTRS)

Grasso, Chris

1990-01-01

TROTER's are small, inexpensive robots that can work together to accomplish sophisticated construction tasks. To understand the issues involved in designing and operating a team of TROTER's, the robots and their components are being modeled. A TROTER system that features standardized component behavior is introduced. An object-oriented model implemented in the Smalltalk programming language is described and the advantages of the object-oriented approach for simulating robot and component interactions are discussed. The presentation includes preliminary results and a discussion of outstanding issues.

Baby MIND Experiment Construction Status

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antonova, M.; et al.

Baby MIND is a magnetized iron neutrino detector, with novel design features, and is planned to serve as a downstream magnetized muon spectrometer for the WAGASCI experiment on the T2K neutrino beam line in Japan. One of the main goals of this experiment is to reduce systematic uncertainties relevant to CP-violation searches, by measuring the neutrino contamination in the anti-neutrino beam mode of T2K. Baby MIND is currently being constructed at CERN, and is planned to be operational in Japan in October 2017.

Layered Composite Analysis Capability

NASA Technical Reports Server (NTRS)

Narayanaswami, R.; Cole, J. G.

1985-01-01

Laminated composite material construction is gaining popularity within industry as an attractive alternative to metallic designs where high strength at reduced weights is of prime consideration. This has necessitated the development of an effective analysis capability for the static, dynamic and buckling analyses of structural components constructed of layered composites. Theoretical and user aspects of layered composite analysis and its incorporation into CSA/NASTRAN are discussed. The availability of stress and strain based failure criteria is described which aids the user in reviewing the voluminous output normally produced in such analyses. Simple strategies to obtain minimum weight designs of composite structures are discussed. Several example problems are presented to demonstrate the accuracy and user convenient features of the capability.

DEVELOPMENT AND DEMONSTRATION OF CONCEPTS FOR IMPROVING COKE-OVEN DOOR SEALS

EPA Science Inventory

The report discusses the design, laboratory scale tests, construction, and field tests of an improved metal-to-metal seal for coke-oven end doors. Basic features of the seal are: high-strength temperature-resistant steel capable of 3 times the deflection of current seals without ...

29 CFR 1910.21 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... but more than 1 inch in its least dimension, in any floor, platform, pavement, or yard, through which.... An opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or... combination of design or construction features in one of the general-purpose types of ladders previously...

29 CFR 1910.21 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... but more than 1 inch in its least dimension, in any floor, platform, pavement, or yard, through which.... An opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or... combination of design or construction features in one of the general-purpose types of ladders previously...

29 CFR 1910.21 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... but more than 1 inch in its least dimension, in any floor, platform, pavement, or yard, through which.... An opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or... combination of design or construction features in one of the general-purpose types of ladders previously...

29 CFR 1910.21 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... but more than 1 inch in its least dimension, in any floor, platform, pavement, or yard, through which.... An opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or... combination of design or construction features in one of the general-purpose types of ladders previously...

29 CFR 1910.21 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... but more than 1 inch in its least dimension, in any floor, platform, pavement, or yard, through which.... An opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or... combination of design or construction features in one of the general-purpose types of ladders previously...

Long term monitoring of carbon composite strands in the Penobscot-Narrows bridge.

DOT National Transportation Integrated Search

2015-06-01

The Penobscot-Narrows Bridge was constructed between May 2003 and December 2006. The bridge is a cable-stayed design with twin pylons and a 2,120-foot span. This cable-stayed bridge features a cradle stay system that : allows for each cable strand in...

MAN-004 Design Standards Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Timothy L.

2014-07-01

At Sandia National Laboratories in New Mexico (SNL/NM), the design, construction, operation, and maintenance of facilities is guided by industry standards, a graded approach, and the systematic analysis of life cycle benefits received for costs incurred. The design of the physical plant must ensure that the facilities are "fit for use," and provide conditions that effectively, efficiently, and safely support current and future mission needs. In addition, SNL/NM applies sustainable design principles, using an integrated whole-building design approach, from site planning to facility design, construction, and operation to ensure building resource efficiency and the health and productivity of occupants. Themore » safety and health of the workforce and the public, any possible effects on the environment, and compliance with building codes take precedence over project issues, such as performance, cost, and schedule. These design standards generally apply to all disciplines on all SNL/NM projects. Architectural and engineering design must be both functional and cost-effective. Facility design must be tailored to fit its intended function, while emphasizing low-maintenance, energy-efficient, and energy-conscious design. Design facilities that can be maintained easily, with readily accessible equipment areas, low maintenance, and quality systems. To promote an orderly and efficient appearance, architectural features of new facilities must complement and enhance the existing architecture at the site. As an Architectural and Engineering (A/E) professional, you must advise the Project Manager when this approach is prohibitively expensive. You are encouraged to use professional judgment and ingenuity to produce a coordinated interdisciplinary design that is cost-effective, easily contractible or buildable, high-performing, aesthetically pleasing, and compliant with applicable building codes. Close coordination and development of civil, landscape, structural, architectural, fire protection, mechanical, electrical, telecommunications, and security features is expected to ensure compatibility with planned functional equipment and to facilitate constructability. If portions of the design are subcontracted to specialists, delivery of the finished design documents must not be considered complete until the subcontracted portions are also submitted for review. You must, along with support consultants, perform functional analyses and programming in developing design solutions. These solutions must reflect coordination of the competing functional, budgetary, and physical requirements for the project. During design phases, meetings between you and the SNL/NM Project Team to discuss and resolve design issues are required. These meetings are a normal part of the design process. For specific design-review requirements, see the project-specific Design Criteria. In addition to the design requirements described in this manual, instructive information is provided to explain the sustainable building practice goals for design, construction, operation, and maintenance of SNL/NM facilities. Please notify SNL/NM personnel of design best practices not included in this manual, so they can be incorporated in future updates.« less

Fluorine and Fluorinated Motifs in the Design and Application of Bioisosteres for Drug Design.

PubMed

Meanwell, Nicholas A

2018-02-05

The electronic properties and relatively small size of fluorine endow it with considerable versatility as a bioisostere and it has found application as a substitute for lone pairs of electrons, the hydrogen atom, and the methyl group while also acting as a functional mimetic of the carbonyl, carbinol, and nitrile moieties. In this context, fluorine substitution can influence the potency, conformation, metabolism, membrane permeability, and P-gp recognition of a molecule and temper inhibition of the hERG channel by basic amines. However, as a consequence of the unique properties of fluorine, it features prominently in the design of higher order structural metaphors that are more esoteric in their conception and which reflect a more sophisticated molecular construction that broadens biological mimesis. In this Perspective, applications of fluorine in the construction of bioisosteric elements designed to enhance the in vitro and in vivo properties of a molecule are summarized.

Extending the construct of psychopathy to youth: implications for understanding, diagnosing, and treating antisocial children and adolescents.

PubMed

Frick, Paul J

2009-12-01

This paper reviews several attempts to extend the construct of psychopathy to children and adolescents. The research suggests that the presence of callous-unemotional (CU) traits may be particularly important. Specifically, the presence of these traits designates a clinically important subgroup of youth with childhood-onset conduct problems who show a particularly severe, aggressive, and stable pattern of antisocial behaviour. Also, children with CU traits show numerous emotional, cognitive, and personality features that are distinct from other antisocial youth that are similar to features found in adults with psychopathy. The research on CU traits has important implications for understanding the different causal pathways through which children develop severe antisocial and aggressive behaviour, as well as implications for diagnosing and intervening with antisocial youth.

Modeling listeners' emotional response to music.

PubMed

Eerola, Tuomas

2012-10-01

An overview of the computational prediction of emotional responses to music is presented. Communication of emotions by music has received a great deal of attention during the last years and a large number of empirical studies have described the role of individual features (tempo, mode, articulation, timbre) in predicting the emotions suggested or invoked by the music. However, unlike the present work, relatively few studies have attempted to model continua of expressed emotions using a variety of musical features from audio-based representations in a correlation design. The construction of the computational model is divided into four separate phases, with a different focus for evaluation. These phases include the theoretical selection of relevant features, empirical assessment of feature validity, actual feature selection, and overall evaluation of the model. Existing research on music and emotions and extraction of musical features is reviewed in terms of these criteria. Examples drawn from recent studies of emotions within the context of film soundtracks are used to demonstrate each phase in the construction of the model. These models are able to explain the dominant part of the listeners' self-reports of the emotions expressed by music and the models show potential to generalize over different genres within Western music. Possible applications of the computational models of emotions are discussed. Copyright © 2012 Cognitive Science Society, Inc.

Design, manufacturing and characterization of aero-elastically scaled wind turbine blades for testing active and passive load alleviation techniques within a ABL wind tunnel

NASA Astrophysics Data System (ADS)

Campagnolo, Filippo; Bottasso, Carlo L.; Bettini, Paolo

2014-06-01

In the research described in this paper, a scaled wind turbine model featuring individual pitch control (IPC) capabilities, and equipped with aero-elastically scaled blades featuring passive load reduction capabilities (bend-twist coupling, BTC), was constructed to investigate, by means of wind tunnel testing, the load alleviation potential of BTC and its synergy with active load reduction techniques. The paper mainly focus on the design of the aero-elastic blades and their dynamic and static structural characterization. The experimental results highlight that manufactured blades show desired bend-twist coupling behavior and are a first milestone toward their testing in the wind tunnel.

Factor structure and construct validity of the psychopathic personality inventory in a forensic sample.

PubMed

Gonsalves, Valerie M; McLawsen, Julia E; Huss, Matthew T; Scalora, Mario J

2013-01-01

A wealth of research has underscored the strong relationship between PCL-R scores and recidivism. However, mounting criticism cites the PCL-R's cumbersome administration procedures and failure to adequately measure core features associated with the construct of psychopathy (Skeem, Polaschek, Patrick, & Lilienfeld, 2011). In light of these concerns, this study examined the PPI and the PPI-R, which were designed to measure core personality features associated with psychopathy (Lilienfeld & Andrews, 1996; Lilienfeld & Widows, 2005). Study one examined the PPI relative to the PCL-R and examined its factor structure. The instruments shared few significant correlations and neither the PCL-R nor the PPI significantly predicted recidivism. Study two examined the PPI-R relative to the PCL-R, the PPI, both history of violence and future criminal activity and measure of related constructs. The PPI-R was significantly correlated with measures of empathy and criminal thinking and the factors were related to a history of violence and predicted future violent criminal behavior. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hardware demonstration of flexible beam control

NASA Technical Reports Server (NTRS)

Schaechter, D. B.

1980-01-01

An experiment employing a pinned-free flexible beam has been constructed to demonstrate and verify several facets of the control of flexible structures. The desired features of the experiment are to demonstrate active shape control, active dynamic control, adaptive control, various control law design approaches, and associated hardware requirements and mechanization difficulties. This paper contains the analytical work performed in support of the facility development, the final design specifications, control law synthesis, and some preliminary results.

State criminal justice telecommunications (STACOM). Volume 4: Network design software user's guide

NASA Technical Reports Server (NTRS)

Lee, J. J.

1977-01-01

A user's guide to the network design program is presented. The program is written in FORTRAN V and implemented on a UNIVAC 1108 computer under the EXEC-8 operating system which enables the user to construct least-cost network topologies for criminal justice digital telecommunications networks. A complete description of program features, inputs, processing logic, and outputs is presented, and a sample run and a program listing are included.

Analyses of Oceanic Subsurface Features Using Space Based Radar Imagery

DTIC Science & Technology

1982-07-01

The relationship of the history of the relative length, speed and height of waves as they approach shallow water is not as simple as indicated in...movement or geometric variation are not shown above and will generally make the construction of an image from collected doppler phase histories more 1...requirements. The design for a ocean mission will be very different from the design for a geologic , geographic or agricultural mission. Application arts

Building America Case Study: Ground Source Heat Pump Research, TaC Studios Residence, Atlanta, Georigia (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-09-01

As part of the NAHB Research Center Industry Partnership, Southface partnered with TaC Studios, an Atlanta based architecture firm specializing in residential and light commercial design, on the construction of a new test home in Atlanta, GA in the mixed-humid climate. This home serves as a residence and home office for the firm's owners, as well as a demonstration of their design approach to potential and current clients. Southface believes the home demonstrates current best practices for the mixed-humid climate, including a building envelope featuring advanced air sealing details and low density spray foam insulation, glazing that exceeds ENERGY STARmore » requirements, and a high performance heating and cooling system. Construction quality and execution was a high priority for TaC Studios and was ensured by a third party review process. Post construction testing showed that the project met stated goals for envelope performance, an air infiltration rate of 2.15 ACH50. The homeowner's wished to further validate whole house energy savings through the project's involvement with Building America and this long-term monitoring effort. As a Building America test home, this home was evaluated to detail whole house energy use, end use loads, and the efficiency and operation of the ground source heat pump and associated systems. Given that the home includes many non-typical end use loads including a home office, pool, landscape water feature, and other luxury features not accounted for in Building America modeling tools, these end uses were separately monitored to determine their impact on overall energy consumption.« less

Establishment of the mathematical model for diagnosing the engine valve faults by genetic programming

NASA Astrophysics Data System (ADS)

Yang, Wen-Xian

2006-05-01

Available machine fault diagnostic methods show unsatisfactory performances on both on-line and intelligent analyses because their operations involve intensive calculations and are labour intensive. Aiming at improving this situation, this paper describes the development of an intelligent approach by using the Genetic Programming (abbreviated as GP) method. Attributed to the simple calculation of the mathematical model being constructed, different kinds of machine faults may be diagnosed correctly and quickly. Moreover, human input is significantly reduced in the process of fault diagnosis. The effectiveness of the proposed strategy is validated by an illustrative example, in which three kinds of valve states inherent in a six-cylinders/four-stroke cycle diesel engine, i.e. normal condition, valve-tappet clearance and gas leakage faults, are identified. In the example, 22 mathematical functions have been specially designed and 8 easily obtained signal features are used to construct the diagnostic model. Different from existing GPs, the diagnostic tree used in the algorithm is constructed in an intelligent way by applying a power-weight coefficient to each feature. The power-weight coefficients vary adaptively between 0 and 1 during the evolutionary process. Moreover, different evolutionary strategies are employed, respectively for selecting the diagnostic features and functions, so that the mathematical functions are sufficiently utilized and in the meantime, the repeated use of signal features may be fully avoided. The experimental results are illustrated diagrammatically in the following sections.

Using research literature to develop a perceptual retraining treatment protocol.

PubMed

Neistadt, M E

1994-01-01

Treatment protocols derived from research literature can help therapists provide more rigorous treatment and more systematic assessment of client progress. This study applied research findings about the influence of task, subject, and feedback parameters on adult performance with block designs to an occupational therapy treatment protocol for parquetry block assembly--an activity occupational therapists use to remediate constructional deficits. Task parameter research suggests that parquetry tasks can be graded according to the features of the design cards, with cards having all block boundaries drawn in being easier than those with some block boundaries omitted. Subject parameter findings suggest that clients' lesions and initial constructional competence can influence their approaches to parquetry tasks. Feedback parameter research suggests that a combination of perceptual and planning cues is most effective for parquetry tasks. Methods to help clients transfer constructional skills from parquetry to functional tasks are also discussed.

A phantom design for assessment of detectability in PET imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wollenweber, Scott D., E-mail: scott.wollenweber@g

2016-09-15

Purpose: The primary clinical role of positron emission tomography (PET) imaging is the detection of anomalous regions of {sup 18}F-FDG uptake, which are often indicative of malignant lesions. The goal of this work was to create a task-configurable fillable phantom for realistic measurements of detectability in PET imaging. Design goals included simplicity, adjustable feature size, realistic size and contrast levels, and inclusion of a lumpy (i.e., heterogeneous) background. Methods: The detection targets were hollow 3D-printed dodecahedral nylon features. The exostructure sphere-like features created voids in a background of small, solid non-porous plastic (acrylic) spheres inside a fillable tank. The featuresmore » filled at full concentration while the background concentration was reduced due to filling only between the solid spheres. Results: Multiple iterations of feature size and phantom construction were used to determine a configuration at the limit of detectability for a PET/CT system. A full-scale design used a 20 cm uniform cylinder (head-size) filled with a fixed pattern of features at a contrast of approximately 3:1. Known signal-present and signal-absent PET sub-images were extracted from multiple scans of the same phantom and with detectability in a challenging (i.e., useful) range. These images enabled calculation and comparison of the quantitative observer detectability metrics between scanner designs and image reconstruction methods. The phantom design has several advantages including filling simplicity, wall-less contrast features, the control of the detectability range via feature size, and a clinically realistic lumpy background. Conclusions: This phantom provides a practical method for testing and comparison of lesion detectability as a function of imaging system, acquisition parameters, and image reconstruction methods and parameters.« less

Principles for the formation of an effective concept of multifunctional high-rise construction investment projects

NASA Astrophysics Data System (ADS)

Beliakov, Sergei

2018-03-01

Investment projects of high-rise construction have a number of features that determine specific risks and additional opportunities that require analysis and accounting in the formation of an effective project concept. The most significant features of high-rise construction include long construction time, complexity of technical and technological solutions, complexity of decisions on the organization of construction and operation, high cost of construction and operation, complexity in determining the ratio of areas designed to accommodate different functional areas, when organizing and coordinating the operation of the facility, with internal zoning. Taking into account the specificity of high-rise construction, among the factors determining the effectiveness of projects, it is advisable to consider as key factors: organizational, technological and investment factors. Within the framework of the article, the author singled out key particular functions for each group of factors under consideration, and also developed a system of principles for the formation of an effective concept of multifunctional high-rise construction investment projects, including the principle of logistic efficiency, the principle of optimal functional zoning, the principle of efficiency of equipment use, the principle of optimizing technological processes, the principle maximization of income, the principle of fund management, the principle of risk management . The model of formation of an effective concept of investment projects of multifunctional high-rise construction developed by the author can contribute to the development of methodological tools in the field of managing the implementation of high-rise construction projects, taking into account their specificity in the current economic conditions.

Design of a Versatile, Teleoperable, Towable Lifting Machine with Robotic Capabilities for Use in Nasa's Lunar Base Operations

NASA Technical Reports Server (NTRS)

Harris, Elizabeth; Ogle, James; Schoppe, Dean

1989-01-01

The lifting machine will assist in lifting cargo off of landers sent to the Moon and in the construction of a lunar base. Three possible designs were considered for the overall configuration of the lifting machine: the variable angle crane, the tower crane, and the gantry crane. Alternate designs were developed for the major components of the lifting machine. A teleoperable, variable angle crane was chosen as its final design. The design consists of a telescoping boom mounted to a chassis that is supported by two conical wheels for towing and four outriggers for stability. Attached to the end of the boom is a seven degree of freedom robot arm for light, dexterous, lifting operations. A cable and hook suspends from the end of the boom for heavy, gross, lifting operations. Approximate structural sizes were determined for the lifter and its components. However, further analysis is needed to determine the optimum design dimensions. The design team also constructed a model of the design which demonstrates its features and operating principals.

Reconsidering Replication: New Perspectives on Large-Scale School Improvement

ERIC Educational Resources Information Center

Peurach, Donald J.; Glazer, Joshua L.

2012-01-01

The purpose of this analysis is to reconsider organizational replication as a strategy for large-scale school improvement: a strategy that features a "hub" organization collaborating with "outlet" schools to enact school-wide designs for improvement. To do so, we synthesize a leading line of research on commercial replication to construct a…

Constructing Domain-Specific Knowledge in Kindergarten: Relations among Knowledge, Intelligence, and Strategic Performance

ERIC Educational Resources Information Center

Alexander, Joyce M.; Johnson, Kathy E.; Leibham, Mary E.; DeBauge, Christiane

2005-01-01

Thirty kindergarten children from two classrooms participated in a 3-week curricular unit on dinosaurs designed to teach taxonomic relations and distinguishing features aligned with 15 dinosaur species. Both domain-specific learning and strategic performance on a Twenty Questions game were assessed twice throughout the curriculum, as well as…

Implementation of a UNIX-Based Network Management System for English Instruction.

ERIC Educational Resources Information Center

Schmitt, Lothar M.; Christianson, Kiel T.

Pedagogical features and implementation of a UNIX-based management system (UNIEM) designed to support the instructor in teaching English as a second language using a network of workstations are described. The application discussed here is for teaching English composition to students at the University of Aizu (Japan). UNIEM is constructed to assist…

Collaborative Learning the Wiki Way

ERIC Educational Resources Information Center

Engstrom, Mary E.; Jewett, Dusty

2005-01-01

In this article, the authors feature the model, Under Control: The Damming of the Missouri River, which was designed to engage middle school students in a real-world geographic issue: investigating the long term environmental, economic and cultural impacts of the 1944 Pick-Sloan Plan, which resulted in the construction of six dams on the Missouri…

Silicon concentrator cell-assembly development

NASA Astrophysics Data System (ADS)

1982-08-01

The purpose was to develop an improved cell assembly design for photovoltaic concentrator receivers. Efforts were concentrated on a study of adhesive/separator systems that might be applied between cell and substrate, because this area holds the key to improved heat transfer, electrical isolation and adhesion. It is also the area in which simpler construction methods offer the greatest benefits for economy and reliability in the manufacturing process. Of the ten most promising designs subjected to rigorous environmental testing, eight designs featuring acrylic and silicon adhesives and fiberglass and polyester separators performed very well.

Xatcobeo: Small Mechanisms for CubeSat Satellites - Antenna and Solar Array Deployment

NASA Technical Reports Server (NTRS)

EncinasPlaza, Jose Miguel; VilanVilan, Jose Antonio; AquadoAgelet, Fernando; BrandiaranMancheno, Javier; LopezEstevez, Miguel; MartinezFernandez, Cesar; SarmientoAres, Fany

2010-01-01

The Xatcobeo project, which includes the mechanisms dealt with here, is principally a university project to design and construct a CubeSat 1U-type satellite. This work describes the design and operational features of the system for antenna storage and deployment, and the design and simulations of the solar array deployment system. It explains the various problems faced and solutions adopted, with a view to providing valid data for any other applications that could find them useful, be they of a similar nature or not.

Random Combinatorial Gradient Metasurface for Broadband, Wide-Angle and Polarization-Independent Diffusion Scattering.

PubMed

Zhuang, Yaqiang; Wang, Guangming; Liang, Jiangang; Cai, Tong; Tang, Xiao-Lan; Guo, Tongfeng; Zhang, Qingfeng

2017-11-29

This paper proposes an easy, efficient strategy for designing broadband, wide-angle and polarization-independent diffusion metasurface for radar cross section (RCS) reduction. A dual-resonance unit cell, composed of a cross wire and cross loop (CWCL), is employed to enhance the phase bandwidth covering the 2π range. Both oblique-gradient and horizontal-gradient phase supercells are designed for illustration. The numerical results agree well with the theoretical ones. To significantly reduce backward scattering, the random combinatorial gradient metasurface (RCGM) is subsequently constructed by collecting eight supercells with randomly distributed gradient directions. The proposed metasurface features an enhanced specular RCS reduction performance and less design complexity compared to other candidates. Both simulated and measured results show that the proposed RCGM can significantly suppress RCS and exhibits broadband, wide-angle and polarization independence features.

Solar power satellite system definition study. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

Configuration concepts, option sizes, and systems definitions study design evolutions are reviewed. The main features of the present reference design silicon solar cell solar power satellite are described, as well as the provisions for space construction and support systems. The principal study accomplishments and conclusions are summarized according to the following tasks: (1) baseline critique; (2) construction and maintenance; (3) industrial complex needs, cost estimates, and production capacity; (4) launch complex requirements at KSC or at an offshore facility; (5) integration of the SPS/ground power network; (6) technology advancement and development; (7) costs and schedules; and (8) exploratory technology: laser annealing of solar cells degraded by proton irradiation, and a fiber-optic phase distribution link at 980 MHz.

The Halogen Bond in the Design of Functional Supramolecular Materials: Recent Advances

PubMed Central

2013-01-01

Halogen bonding is an emerging noncovalent interaction for constructing supramolecular assemblies. Though similar to the more familiar hydrogen bonding, four primary differences between these two interactions make halogen bonding a unique tool for molecular recognition and the design of functional materials. First, halogen bonds tend to be much more directional than (single) hydrogen bonds. Second, the interaction strength scales with the polarizability of the bond-donor atom, a feature that researchers can tune through single-atom mutation. In addition, halogen bonds are hydrophobic whereas hydrogen bonds are hydrophilic. Lastly, the size of the bond-donor atom (halogen) is significantly larger than hydrogen. As a result, halogen bonding provides supramolecular chemists with design tools that cannot be easily met with other types of noncovalent interactions and opens up unprecedented possibilities in the design of smart functional materials. This Account highlights the recent advances in the design of halogen-bond-based functional materials. Each of the unique features of halogen bonding, directionality, tunable interaction strength, hydrophobicity, and large donor atom size, makes a difference. Taking advantage of the hydrophobicity, researchers have designed small-size ion transporters. The large halogen atom size provided a platform for constructing all-organic light-emitting crystals that efficiently generate triplet electrons and have a high phosphorescence quantum yield. The tunable interaction strengths provide tools for understanding light-induced macroscopic motions in photoresponsive azobenzene-containing polymers, and the directionality renders halogen bonding useful in the design on functional supramolecular liquid crystals and gel-phase materials. Although halogen bond based functional materials design is still in its infancy, we foresee a bright future for this field. We expect that materials designed based on halogen bonding could lead to applications in biomimetics, optics/photonics, functional surfaces, and photoswitchable supramolecules. PMID:23805801

Tools reference manual for a Requirements Specification Language (RSL), version 2.0

NASA Technical Reports Server (NTRS)

Fisher, Gene L.; Cohen, Gerald C.

1993-01-01

This report describes a general-purpose Requirements Specification Language, RSL. The purpose of RSL is to specify precisely the external structure of a mechanized system and to define requirements that the system must meet. A system can be comprised of a mixture of hardware, software, and human processing elements. RSL is a hybrid of features found in several popular requirements specification languages, such as SADT (Structured Analysis and Design Technique), PSL (Problem Statement Language), and RMF (Requirements Modeling Framework). While languages such as these have useful features for structuring a specification, they generally lack formality. To overcome the deficiencies of informal requirements languages, RSL has constructs for formal mathematical specification. These constructs are similar to those found in formal specification languages such as EHDM (Enhanced Hierarchical Development Methodology), Larch, and OBJ3.

Elementary students' engagement in failure-prone engineering design tasks

NASA Astrophysics Data System (ADS)

Andrews, Chelsea Joy

Although engineering education has been practiced at the undergraduate level for over a century, only fairly recently has the field broadened to include the elementary level; the pre-college division of the American Society of Engineering Education was established in 2003. As a result, while recent education standards require engineering in elementary schools, current studies are still filling in basic research on how best to design and implement elementary engineering activities. One area in need of investigation is how students engage with physical failure in design tasks. In this dissertation, I explore how upper elementary students engage in failure-prone engineering design tasks in an out-of-school environment. In a series of three empirical case studies, I look closely at how students evaluate failed tests and decide on changes to their design constructions, how their reasoning evolves as they repeatedly encounter physical failure, and how students and facilitators co-construct testing norms where repetitive failure is manageable. I also briefly investigate how students' engagement differs in a task that features near-immediate success. By closely examining student groups' discourse and their interactions with their design constructions, I found that these students: are able to engage in iteration and see failure-as-feedback with minimal externally-imposed structure; seem to be designing in a more sophisticated manner, attending to multiple causal factors, after experiencing repetitive failure; and are able to manage the stress and frustration of repetitive failure, provided the co-constructed testing norms of the workshop environment are supportive of failure management. These results have both pedagogical implications, in terms of how to create and facilitate design tasks, and methodological implications--namely, I highlight the particular insights afforded by a case study approach for analyzing engagement in design tasks.

Transitioning to High Performance Homes: Successes and Lessons Learned From Seven Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widder, Sarah H.; Kora, Angela R.; Baechler, Michael C.

2013-03-01

As homebuyers are becoming increasingly concerned about rising energy costs and the impact of fossil fuels as a major source of greenhouse gases, the returning new home market is beginning to demand energy-efficient and comfortable high-performance homes. In response to this, some innovative builders are gaining market share because they are able to market their homes’ comfort, better indoor air quality, and aesthetics, in addition to energy efficiency. The success and marketability of these high-performance homes is creating a builder demand for house plans and information about how to design, build, and sell their own low-energy homes. To help makemore » these and other builders more successful in the transition to high-performance construction techniques, Pacific Northwest National Laboratory (PNNL) partnered with seven interested builders in the hot humid and mixed humid climates to provide technical and design assistance through two building science firms, Florida Home Energy and Resources Organization (FL HERO) and Calcs-Plus, and a designer that offers a line of stock plans designed specifically for energy efficiency, called Energy Smart Home Plans (ESHP). This report summarizes the findings of research on cost-effective high-performance whole-house solutions, focusing on real-world implementation and challenges and identifying effective solutions. The ensuing sections provide project background, profile each of the builders who participated in the program, and describe their houses’ construction characteristics, key challenges the builders encountered during the construction and transaction process); and present primary lessons learned to be applied to future projects. As a result of this technical assistance, 17 homes have been built featuring climate-appropriate efficient envelopes, ducts in conditioned space, and correctly sized and controlled heating, ventilation, and air-conditioning systems. In addition, most builders intend to integrate high-performance features into most or all their homes in the future. As these seven builders have demonstrated, affordable, high-performance homes are possible, but require attention to detail and flexibility in design to accommodate specific regional geographic or market-driven constraints that can increase cost. With better information regarding how energy-efficiency trade-offs or design choices affect overall home performance, builders can make informed decisions regarding home design and construction to minimize cost without sacrificing performance and energy savings.« less

An assessment of the performance of municipal constructed wetlands in Ireland.

PubMed

Hickey, Anthony; Arnscheidt, Joerg; Joyce, Eadaoin; O'Toole, James; Galvin, Gerry; O' Callaghan, Mark; Conroy, Ken; Killian, Darran; Shryane, Tommy; Hughes, Francis; Walsh, Katherine; Kavanagh, Emily

2018-03-15

While performance assessments of constructed wetlands sites around the world have appraised their capacity for effective removal of organics, a large variance remains in these sites' reported ability to retain nutrients, which appears to depend on differences in design, operation and climate factors. Nutrient retention is a very important objective for constructed wetlands, to avoid eutrophication of aquatic environments receiving their effluents. This study assessed the performance of constructed wetlands in terms of nutrient retention and associated parameters under the humid conditions of Ireland's temperate maritime climate. A review of the performance of 52 constructed wetland sites from 17 local authorities aimed to identify the best performing types of constructed wetlands and the treatment factors determining successful compliance with environmental standards. Data analysis compared effluent results from constructed wetlands with secondary free surface flow or tertiary horizontal subsurface flow, hybrid systems and integrated constructed wetlands with those from small-scale mechanical wastewater treatment plants of the same size class. Nutrient concentrations in effluents of constructed wetlands were negatively correlated (p < .01) with specific area, i.e. the ratio of surface area and population equivalents. The latest generation of integrated constructed wetlands, which had applied design guidelines issued by the Department of the Environment, performed best. Storm management design features improved treatment performance of constructed wetlands significantly (p < .05) for total suspended solids concentrations and exceedance frequency of limit values for total nitrogen. Mechanical wastewater treatment plants, secondary free surface water and tertiary horizontal subsurface flow wetlands showed a very large variance in effluent concentrations for organic and nutrient parameters. E. coli numbers in effluents were lowest for integrated constructed wetlands with an arithmetic mean of 89 MPN/100 ml. Despite Ireland's humid climate, some constructed wetland sites achieved long or frequent periods of zero effluent discharge and thus did not transfer any waterborne pollution to their receptors during these periods. Copyright © 2018 Elsevier Ltd. All rights reserved.

Human body as a set of biometric features identified by means of optoelectronics

NASA Astrophysics Data System (ADS)

Podbielska, Halina; Bauer, Joanna

2005-09-01

Human body posses many unique, singular features that are impossible to copy or forge. Nowadays, to establish and to ensure the public security requires specially designed devices and systems. Biometrics is a field of science and technology, exploiting human body characteristics for people recognition. It identifies the most characteristic and unique ones in order to design and construct systems capable to recognize people. In this paper some overview is given, presenting the achievements in biometrics. The verification and identification process is explained, along with the way of evaluation of biometric recognition systems. The most frequently human biometrics used in practice are shortly presented, including fingerprints, facial imaging (including thermal characteristic), hand geometry and iris patterns.

Information model construction of MES oriented to mechanical blanking workshop

NASA Astrophysics Data System (ADS)

Wang, Jin-bo; Wang, Jin-ye; Yue, Yan-fang; Yao, Xue-min

2016-11-01

Manufacturing Execution System (MES) is one of the crucial technologies to implement informatization management in manufacturing enterprises, and the construction of its information model is the base of MES database development. Basis on the analysis of the manufacturing process information in mechanical blanking workshop and the information requirement of MES every function module, the IDEF1X method was adopted to construct the information model of MES oriented to mechanical blanking workshop, and a detailed description of the data structure feature included in MES every function module and their logical relationship was given from the point of view of information relationship, which laid the foundation for the design of MES database.

Synthetic approaches to construct viral capsid-like spherical nanomaterials.

PubMed

Matsuura, Kazunori

2018-06-06

This feature article describes recent progress in synthetic strategies to construct viral capsid-like spherical nanomaterials using the self-assembly of peptides and/or proteins. By mimicking the self-assembly of spherical viral capsids and clathrin, trigonal peptide conjugates bearing β-sheet-forming peptides, glutathiones, or coiled-coil-forming peptides were developed to construct viral capsid-like particles. β-Annulus peptides from tomato bushy stunt virus self-assembled into viral capsid-like nanocapsules with a size of 30-50 nm, which could encapsulate various guest molecules and be decorated with different molecules on their surface. Rationally designed fusion proteins bearing symmetric assembling units afforded precise viral capsid-like polyhedral assemblies. These synthetic approaches to construct artificial viruses could become useful guidelines to develop novel drug carriers, vaccine platforms, nanotemplates and nanoreactors.

Classifier ensemble construction with rotation forest to improve medical diagnosis performance of machine learning algorithms.

PubMed

Ozcift, Akin; Gulten, Arif

2011-12-01

Improving accuracies of machine learning algorithms is vital in designing high performance computer-aided diagnosis (CADx) systems. Researches have shown that a base classifier performance might be enhanced by ensemble classification strategies. In this study, we construct rotation forest (RF) ensemble classifiers of 30 machine learning algorithms to evaluate their classification performances using Parkinson's, diabetes and heart diseases from literature. While making experiments, first the feature dimension of three datasets is reduced using correlation based feature selection (CFS) algorithm. Second, classification performances of 30 machine learning algorithms are calculated for three datasets. Third, 30 classifier ensembles are constructed based on RF algorithm to assess performances of respective classifiers with the same disease data. All the experiments are carried out with leave-one-out validation strategy and the performances of the 60 algorithms are evaluated using three metrics; classification accuracy (ACC), kappa error (KE) and area under the receiver operating characteristic (ROC) curve (AUC). Base classifiers succeeded 72.15%, 77.52% and 84.43% average accuracies for diabetes, heart and Parkinson's datasets, respectively. As for RF classifier ensembles, they produced average accuracies of 74.47%, 80.49% and 87.13% for respective diseases. RF, a newly proposed classifier ensemble algorithm, might be used to improve accuracy of miscellaneous machine learning algorithms to design advanced CADx systems. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

The Point of It All: Exploring Variations in Wind Vane Design

ERIC Educational Resources Information Center

Koballa, Thomas, Jr.

2008-01-01

A wind vane is a tool for making observations of wind direction and initiating inquiries about the weather. Its construction and use continue to be mainstays of the science education of elementary students. By providing students with the opportunity to discern critical features associated with the wind vane's operation, you can ensure that…

Serb guardrail in-service evaluation : S. Ashland to California State Line, F.A.P. IR-5-1(113)00, Jackson County : experimental features construction-report.

DOT National Transportation Integrated Search

1990-03-01

This report covers the installation of two Self-Restoring Barrier (SERB) guardrails on Interstate-5 south of Ashland Oregon. The SERB design was developed to reduce repair cost and increase safety when compared to conventional barriers. This is accom...

ICT and Knowledge Construction: Towards New Features for the Socio-Technical Approach

ERIC Educational Resources Information Center

Cartelli, Antonio

2007-01-01

Purpose: The purpose of this paper is to provide an analysis and review of the sociotechnical approach as a result of analysis of experiences with the introduction of ICT in higher education. Design/methodology/approach: The experiences of the author with the creation of special web sites in palaeography are analysed paying special attention to…

10 CFR 50.13 - Attacks and destructive acts by enemies of the United States; and defense activities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... LICENSING OF PRODUCTION AND UTILIZATION FACILITIES Requirement of License, Exceptions § 50.13 Attacks and... construct and operate a production or utilization facility, or for an amendment to such license, is not required to provide for design features or other measures for the specific purpose of protection against...

Dataflow models for fault-tolerant control systems

NASA Technical Reports Server (NTRS)

Papadopoulos, G. M.

1984-01-01

Dataflow concepts are used to generate a unified hardware/software model of redundant physical systems which are prone to faults. Basic results in input congruence and synchronization are shown to reduce to a simple model of data exchanges between processing sites. Procedures are given for the construction of congruence schemata, the distinguishing features of any correctly designed redundant system.

Gen Y Recruitment: Understanding Graduate Intentions to Join an Organisation Using the Theory of Planned Behaviour

ERIC Educational Resources Information Center

Warmerdam, Amanda; Lewis, Ioni; Banks, Tamara

2015-01-01

Purpose: Using the Theory of Planned Behaviour (TPB) framework, the purpose of this paper is to explore whether the standard TPB constructs explained variance in Generation Y (Gen Y) individuals' intentions to join their ideal organisation. Design/methodology/approach: A mixed methods approach was used featuring qualitative and quantitative…

Electrochemical construction

DOEpatents

Einstein, Harry; Grimes, Patrick G.

1983-08-23

An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

Recovering faces from memory: the distracting influence of external facial features.

PubMed

Frowd, Charlie D; Skelton, Faye; Atherton, Chris; Pitchford, Melanie; Hepton, Gemma; Holden, Laura; McIntyre, Alex H; Hancock, Peter J B

2012-06-01

Recognition memory for unfamiliar faces is facilitated when contextual cues (e.g., head pose, background environment, hair and clothing) are consistent between study and test. By contrast, inconsistencies in external features, especially hair, promote errors in unfamiliar face-matching tasks. For the construction of facial composites, as carried out by witnesses and victims of crime, the role of external features (hair, ears, and neck) is less clear, although research does suggest their involvement. Here, over three experiments, we investigate the impact of external features for recovering facial memories using a modern, recognition-based composite system, EvoFIT. Participant-constructors inspected an unfamiliar target face and, one day later, repeatedly selected items from arrays of whole faces, with "breeding," to "evolve" a composite with EvoFIT; further participants (evaluators) named the resulting composites. In Experiment 1, the important internal-features (eyes, brows, nose, and mouth) were constructed more identifiably when the visual presence of external features was decreased by Gaussian blur during construction: higher blur yielded more identifiable internal-features. In Experiment 2, increasing the visible extent of external features (to match the target's) in the presented face-arrays also improved internal-features quality, although less so than when external features were masked throughout construction. Experiment 3 demonstrated that masking external-features promoted substantially more identifiable images than using the previous method of blurring external-features. Overall, the research indicates that external features are a distractive rather than a beneficial cue for face construction; the results also provide a much better method to construct composites, one that should dramatically increase identification of offenders.

Health Behavior Theory in Physical Activity Game Apps: A Content Analysis

PubMed Central

Moxley, Victor BA; MacDonald, Elizabeth

2015-01-01

Background Physical activity games developed for a mobile phone platform are becoming increasingly popular, yet little is known about their content or inclusion of health behavior theory (HBT). Objective The objective of our study was to quantify elements of HBT in physical activity games developed for mobile phones and to assess the relationship between theoretical constructs and various app features. Methods We conducted an analysis of exercise and physical activity game apps in the Apple App Store in the fall of 2014. A total of 52 apps were identified and rated for inclusion of health behavior theoretical constructs using an established theory-based rubric. Each app was coded for 100 theoretical items, containing 5 questions for 20 different constructs. Possible total theory scores ranged from 0 to 100. Descriptive statistics and Spearman correlations were used to describe the HBT score and association with selected app features, respectively. Results The average HBT score in the sample was 14.98 out of 100. One outlier, SuperBetter, scored higher than the other apps with a score of 76. Goal setting, self-monitoring, and self-reward were the most-reported constructs found in the sample. There was no association between either app price and theory score (P=.5074), or number of gamification elements and theory score (P=.5010). However, Superbetter, with the highest HBT score, was also the most expensive app. Conclusions There are few content analyses of serious games for health, but a comparison between these findings and previous content analyses of non-game health apps indicates that physical activity mobile phone games demonstrate higher levels of behavior theory. The most common theoretical constructs found in this sample are known to be efficacious elements in physical activity interventions. It is unclear, however, whether app designers consciously design physical activity mobile phone games with specific constructs in mind; it may be that games lend themselves well to inclusion of theory and any constructs found in significant levels are coincidental. Health games developed for mobile phones could be potentially used in health interventions, but collaboration between app designers and behavioral specialists is crucial. Additionally, further research is needed to better characterize mobile phone health games and the relative importance of educational elements versus gamification elements in long-term behavior change. PMID:26168926

Health Behavior Theory in Physical Activity Game Apps: A Content Analysis.

PubMed

Payne, Hannah E; Moxley, Victor Ba; MacDonald, Elizabeth

2015-07-13

Physical activity games developed for a mobile phone platform are becoming increasingly popular, yet little is known about their content or inclusion of health behavior theory (HBT). The objective of our study was to quantify elements of HBT in physical activity games developed for mobile phones and to assess the relationship between theoretical constructs and various app features. We conducted an analysis of exercise and physical activity game apps in the Apple App Store in the fall of 2014. A total of 52 apps were identified and rated for inclusion of health behavior theoretical constructs using an established theory-based rubric. Each app was coded for 100 theoretical items, containing 5 questions for 20 different constructs. Possible total theory scores ranged from 0 to 100. Descriptive statistics and Spearman correlations were used to describe the HBT score and association with selected app features, respectively. The average HBT score in the sample was 14.98 out of 100. One outlier, SuperBetter, scored higher than the other apps with a score of 76. Goal setting, self-monitoring, and self-reward were the most-reported constructs found in the sample. There was no association between either app price and theory score (P=.5074), or number of gamification elements and theory score (P=.5010). However, Superbetter, with the highest HBT score, was also the most expensive app. There are few content analyses of serious games for health, but a comparison between these findings and previous content analyses of non-game health apps indicates that physical activity mobile phone games demonstrate higher levels of behavior theory. The most common theoretical constructs found in this sample are known to be efficacious elements in physical activity interventions. It is unclear, however, whether app designers consciously design physical activity mobile phone games with specific constructs in mind; it may be that games lend themselves well to inclusion of theory and any constructs found in significant levels are coincidental. Health games developed for mobile phones could be potentially used in health interventions, but collaboration between app designers and behavioral specialists is crucial. Additionally, further research is needed to better characterize mobile phone health games and the relative importance of educational elements versus gamification elements in long-term behavior change.

Wurfelspiel-based training data methods for ATR

NASA Astrophysics Data System (ADS)

Peterson, James K.

2004-09-01

A data object is constructed from a P by M Wurfelspiel matrix W by choosing an entry from each column to construct a sequence A0A1"AM-1. Each of the PM possibilities are designed to correspond to the same category according to some chosen measure. This matrix could encode many types of data. (1) Musical fragments, all of which evoke sadness; each column entry is a 4 beat sequence with a chosen A0A1A2 thus 16 beats long (W is P by 3). (2) Paintings, all of which evoke happiness; each column entry is a layer and a given A0A1A2 is a painting constructed using these layers (W is P by 3). (3) abstract feature vectors corresponding to action potentials evoked from a biological cell's exposure to a toxin. The action potential is divided into four relevant regions and each column entry represents the feature vector of a region. A given A0A1A2 is then an abstraction of the excitable cell's output (W is P by 4). (4) abstract feature vectors corresponding to an object such as a face or vehicle. The object is divided into four categories each assigned an abstract feature vector with the resulting concatenation an abstract representation of the object (W is P by 4). All of the examples above correspond to one particular measure (sad music, happy paintings, an introduced toxin, an object to recognize)and hence, when a Wurfelspiel matrix is constructed, relevant training information for recognition is encoded that can be used in many algorithms. The focus of this paper is on the application of these ideas to automatic target recognition (ATR). In addition, we discuss a larger biologically based model of temporal cortex polymodal sensor fusion which can use the feature vectors extracted from the ATR Wurfelspiel data.

Zeolite-like metal–organic frameworks (ZMOFs): Design, synthesis, and properties

DOE PAGES

Eddaoudi, Mohamed; Sava, Dorina F.; Eubank, Jarrod F.; ...

2015-10-24

This study highlights various design and synthesis approaches toward the construction of ZMOFs, which are metal–organic frameworks (MOFs) with topologies and, in some cases, features akin to traditional inorganic zeolites. The interest in this unique subset of MOFs is correlated with their exceptional characteristics arising from the periodic pore systems and distinctive cage-like cavities, in conjunction with modular intra- and/or extra-framework components, which ultimately allow for tailoring of the pore size, pore shape, and properties towards specific applications.

Designing algorithm visualization on mobile platform: The proposed guidelines

NASA Astrophysics Data System (ADS)

Supli, A. A.; Shiratuddin, N.

2017-09-01

This paper entails an ongoing study about the design guidelines of algorithm visualization (AV) on mobile platform, helping students learning data structures and algorithm (DSA) subject effectively. Our previous review indicated that design guidelines of AV on mobile platform are still few. Mostly, previous guidelines of AV are developed for AV on desktop and website platform. In fact, mobile learning has been proved to enhance engagement in learning circumstances, and thus effect student's performance. In addition, the researchers highly recommend including UI design and Interactivity in designing effective AV system. However, the discussions of these two aspects in previous AV design guidelines are not comprehensive. The UI design in this paper describes the arrangement of AV features in mobile environment, whereas interactivity is about the active learning strategy features based on learning experiences (how to engage learners). Thus, this study main objective is to propose design guidelines of AV on mobile platform (AVOMP) that entails comprehensively UI design and interactivity aspects. These guidelines are developed through content analysis and comparative analysis from various related studies. These guidelines are useful for AV designers to help them constructing AVOMP for various topics on DSA.

How time delay and network design shape response patterns in biochemical negative feedback systems.

PubMed

Börsch, Anastasiya; Schaber, Jörg

2016-08-24

Negative feedback in combination with time delay can bring about both sustained oscillations and adaptive behaviour in cellular networks. Here, we study which design features of systems with delayed negative feedback shape characteristic response patterns with special emphasis on the role of time delay. To this end, we analyse generic two-dimensional delay differential equations describing the dynamics of biochemical signal-response networks. We investigate the influence of several design features on the stability of the model equilibrium, i.e., presence of auto-inhibition and/or mass conservation and the kind and/or strength of the delayed negative feedback. We show that auto-inhibition and mass conservation have a stabilizing effect, whereas increasing abruptness and decreasing feedback threshold have a de-stabilizing effect on the model equilibrium. Moreover, applying our theoretical analysis to the mammalian p53 system we show that an auto-inhibitory feedback can decouple period and amplitude of an oscillatory response, whereas the delayed feedback can not. Our theoretical framework provides insight into how time delay and design features of biochemical networks act together to elicit specific characteristic response patterns. Such insight is useful for constructing synthetic networks and controlling their behaviour in response to external stimulation.

Advanced Design Features of APR1400 and Realization in Shin Kori Construction Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

OH, S.J.; Park, K.C.; Kim, H.G.

2006-07-01

APR1400 adopted several advanced design features. To ensure their proper operation as a part of ShinKori 3,4 project, both experimental and analytical work are continuing. In this paper, work on the advanced design features related to enhanced safety is examined. APR1400 safety injection system consists of four independent trains which include four safety injection pump and tanks. A passive flow regulating device called fluidic device is installed in the safety injection tanks. Separate effect tests including a full scale fluidic device tests have been conducted. Integral system tests are in progress. Combination of these work with the analytical work usingmore » RELAP5/Mod3 would ensure the proper operation of the new safety injection systems. To mitigate severe accidents, hydrogen mitigation system using PARs and igniters is adopted. Also, active injection system and the streamlined insulation design are adopted to enhance the in-vessel retention capability with the external cooling of RPV strategy. Analytic work with supporting experiments is performed. We are certain that these preparatory work would help the successful adaptation of ADF in ShinKori project. (authors)« less

RESIDENTIAL RADON RESISTANT CONSTRUCTION FEATURE SELECTION SYSTEM

EPA Science Inventory

The report describes a proposed residential radon resistant construction feature selection system. The features consist of engineered barriers to reduce radon entry and accumulation indoors. The proposed Florida standards require radon resistant features in proportion to regional...

Receptive fields selection for binary feature description.

PubMed

Fan, Bin; Kong, Qingqun; Trzcinski, Tomasz; Wang, Zhiheng; Pan, Chunhong; Fua, Pascal

2014-06-01

Feature description for local image patch is widely used in computer vision. While the conventional way to design local descriptor is based on expert experience and knowledge, learning-based methods for designing local descriptor become more and more popular because of their good performance and data-driven property. This paper proposes a novel data-driven method for designing binary feature descriptor, which we call receptive fields descriptor (RFD). Technically, RFD is constructed by thresholding responses of a set of receptive fields, which are selected from a large number of candidates according to their distinctiveness and correlations in a greedy way. Using two different kinds of receptive fields (namely rectangular pooling area and Gaussian pooling area) for selection, we obtain two binary descriptors RFDR and RFDG .accordingly. Image matching experiments on the well-known patch data set and Oxford data set demonstrate that RFD significantly outperforms the state-of-the-art binary descriptors, and is comparable with the best float-valued descriptors at a fraction of processing time. Finally, experiments on object recognition tasks confirm that both RFDR and RFDG successfully bridge the performance gap between binary descriptors and their floating-point competitors.

Superconducting Magnets for Accelerators

NASA Astrophysics Data System (ADS)

Brianti, G.; Tortschanoff, T.

1993-03-01

This chapter describes the main features of superconducting magnets for high energy synchrotrons and colliders. It refers to magnets presently used and under development for the most advanced accelerators projects, both recently constructed or in the preparatory phase. These magnets, using the technology mainly based on the NbTi conductor, are described from the aspect of design, materials, construction and performance. The trend toward higher performance can be gauged from the doubling of design field in less than a decade from about 4 T for the Tevatron to 10 T for the LHC. Special properties of the superconducting accelerator magnets, such as their general layout and the need of extensive computational treatment, the limits of performance inherent to the available conductors, the requirements on the structural design are described. The contribution is completed by elaborating on persistent current effects, quench protection and the cryostat design. As examples the main magnets for HERA and SSC, as well as the twin-aperture magnets for LHC, are presented.

Design, construction and commissioning of the Digital Hadron Calorimeter—DHCAL

NASA Astrophysics Data System (ADS)

Adams, C.; Bambaugh, A.; Bilki, B.; Butler, J.; Corriveau, F.; Cundiff, T.; Drake, G.; Francis, K.; Furst, B.; Guarino, V.; Haberichter, B.; Hazen, E.; Hoff, J.; Holm, S.; Kreps, A.; DeLurgio, P.; Matijas, Z.; Dal Monte, L.; Mucia, N.; Norbeck, E.; Northacker, D.; Onel, Y.; Pollack, B.; Repond, J.; Schlereth, J.; Skrzecz, F.; Smith, J. R.; Trojand, D.; Underwood, D.; Velasco, M.; Walendziak, J.; Wood, K.; Wu, S.; Xia, L.; Zhang, Q.; Zhao, A.

2016-07-01

A novel hadron calorimeter is being developed for future lepton colliding beam detectors. The calorimeter is optimized for the application of Particle Flow Algorithms (PFAs) to the measurement of hadronic jets and features a very finely segmented readout with 1 × 1 cm2 cells. The active media of the calorimeter are Resistive Plate Chambers (RPCs) with a digital, i.e. one-bit, readout. To first order the energy of incident particles in this calorimeter is reconstructed as being proportional to the number of pads with a signal over a given threshold. A large-scale prototype calorimeter with approximately 500,000 readout channels has been built and underwent extensive testing in the Fermilab and CERN test beams. This paper reports on the design, construction, and commissioning of this prototype calorimeter.

EOS: A project to investigate the design and construction of real-time distributed Embedded Operating Systems

NASA Technical Reports Server (NTRS)

Campbell, R. H.; Essick, Ray B.; Johnston, Gary; Kenny, Kevin; Russo, Vince

1987-01-01

Project EOS is studying the problems of building adaptable real-time embedded operating systems for the scientific missions of NASA. Choices (A Class Hierarchical Open Interface for Custom Embedded Systems) is an operating system designed and built by Project EOS to address the following specific issues: the software architecture for adaptable embedded parallel operating systems, the achievement of high-performance and real-time operation, the simplification of interprocess communications, the isolation of operating system mechanisms from one another, and the separation of mechanisms from policy decisions. Choices is written in C++ and runs on a ten processor Encore Multimax. The system is intended for use in constructing specialized computer applications and research on advanced operating system features including fault tolerance and parallelism.

CAD-model-based vision for space applications

NASA Technical Reports Server (NTRS)

Shapiro, Linda G.

1988-01-01

A pose acquisition system operating in space must be able to perform well in a variety of different applications including automated guidance and inspections tasks with many different, but known objects. Since the space station is being designed with automation in mind, there will be CAD models of all the objects, including the station itself. The construction of vision models and procedures directly from the CAD models is the goal of this project. The system that is being designed and implementing must convert CAD models to vision models, predict visible features from a given view point from the vision models, construct view classes representing views of the objects, and use the view class model thus derived to rapidly determine the pose of the object from single images and/or stereo pairs.

Method of constructing an improved electrochemical cell

DOEpatents

Grimes, Patrick G.; Einstein, Harry

1984-10-09

An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

Man-Amplifying Exoskeleton

NASA Astrophysics Data System (ADS)

Rosheim, Mark E.

1990-03-01

This paper describes a design for a man-amplifying exoskeleton, an electrically powered, articulated frame worn by an operator. The design features modular construction and employ anthropomorphic pitch-yaw joints for arms and legs. These singularity-free designs offer a significant advancement over simple pivot-type joints used in older designs. Twenty-six degrees-of-freedom excluding the hands gives the Man-Amplifier its unique dexterity. A five hundred-pound load capacity is engineered for a diverse range of tasks. Potential applications in emergency rescue work, restoring functionality to the handicapped, and military applications ranging from material handling to an elite fighting core are discussed. A bibliography concludes this paper.

Staff Nurse Perceptions of Open-Pod and Single Family Room NICU Designs on Work Environment and Patient Care.

PubMed

Winner-Stoltz, Regina; Lengerich, Alexander; Hench, Anna Jeanine; OʼMalley, Janet; Kjelland, Kimberly; Teal, Melissa

2018-06-01

Neonatal intensive care units have historically been constructed as open units or multiple-bed bays, but since the 1990s, the trend has been toward single family room (SFR) units. The SFR design has been found to promote family-centered care and to improve patient outcomes and safety. The impact of the SFR design NICU on staff, however, has been mixed. The purposes of this study were to compare staff nurse perceptions of their work environments in an open-pod versus an SFR NICU and to compare staff nurse perceptions of the impact of 2 NICU designs on the care they provide for patients/families. A prospective cohort study was conducted. Questionnaires were completed at 6 months premove and again at 3, 9, and 15 months postmove. A series of 1-way analyses of variance were conducted to compare each group in each of the 8 domains. Open-ended questions were evaluated using thematic analysis. The SFR design is favorable in relation to environmental quality and control of primary workspace, privacy and interruption, unit features supporting individual work, and unit features supporting teamwork; the open-pod design is preferable in relation to walking. Incorporating design features that decrease staff isolation and walking and ensuring both patient and staff safety and security are important considerations. Further study is needed on unit design at a microlevel including headwall design and human milk mixing areas, as well as on workflow processes.

Metalinguistic Knowledge of Salient vs. Unsalient Features: Evidence from the Arabic Construct State

ERIC Educational Resources Information Center

Azaz, Mahmoud

2017-01-01

This study examined to what extent English-speaking learners of Arabic demonstrated varied metalinguistic knowledge of a salient feature (head-direction) vs. an unsalient feature (definiteness) in the Arabic construct state. In addition, it examined whether this knowledge was utilized in form-focused task performance. In the target construction,…

Programming Language Software For Graphics Applications

NASA Technical Reports Server (NTRS)

Beckman, Brian C.

1993-01-01

New approach reduces repetitive development of features common to different applications. High-level programming language and interactive environment with access to graphical hardware and software created by adding graphical commands and other constructs to standardized, general-purpose programming language, "Scheme". Designed for use in developing other software incorporating interactive computer-graphics capabilities into application programs. Provides alternative to programming entire applications in C or FORTRAN, specifically ameliorating design and implementation of complex control and data structures typifying applications with interactive graphics. Enables experimental programming and rapid development of prototype software, and yields high-level programs serving as executable versions of software-design documentation.

Design of electromagnetic bearing for vibration control of flexible transmission shaft

NASA Technical Reports Server (NTRS)

Gondhalekar, V.; Holmes, R.

1984-01-01

Recently magnetic bearings were proposed by several researchers and shown to be viable on a variety of rotor assemblies. The design and construction of such a bearing, which employs features hitherto not used by other workers is examined. These include an original approach to the design of the electromagnets and their amplifiers, and to software in a digital control system, to condition the control signals so as to make the magnets appear to be linear and uncoupled. The resulting system is used to control a rotor-bearing assembly, whose speed range covers two flexural-critical speeds.

Design Features and Commissioning of the Versatile Experiment Spherical Torus (VEST) at Seoul National University

NASA Astrophysics Data System (ADS)

J. Chung, K.; H. An, Y.; K. Jung, B.; Y. Lee, H.; C., Sung; S. Na, Y.; S. Hahm, T.; S. Hwang, Y.

2013-03-01

A new spherical torus called VEST (Versatile Experiment Spherical Torus) is designed, constructed and successfully commissioned at Seoul National University. A unique design feature of the VEST is two partial solenoid coils installed at both vertical ends of a center stack, which can provide sufficient magnetic fluxes to initiate tokamak plasmas while keeping a low aspect ratio configuration in the central region. According to initial double null merging start-up scenario using the partial solenoid coils, appropriate power supplies for driving a toroidal field coil, outer poloidal field coils, and the partial solenoid coils are fabricated and successfully commissioned. For reliable start-up, a pre-ionization system with two cost-effective homemade magnetron power supplies is also prepared. In addition, magnetic and spectroscopic diagnostics with appropriate data acquisition and control systems are well prepared for initial operation of the device. The VEST is ready for tokamak plasma operation by completing and commissioning most of the designed components.

Design and operation of small biogas plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdel-Dayem, A.M.; Hamad, M.A.

1980-12-01

This paper concentrates on the experience gained from the adaptation of the Chinese biogas technology to rural areas of Egypt. Three different prototype digesters have been constructed. The first is a 10 M/sup 3/ rectangular digester of the water pressure type, the second is a 6 M/sup 3/ circular and shallow digester with domed roof and dished bottom. The third prototype unit with a capacity of 7 M/sup 3/ has been recently constructed. It combines the features of both plug flow and the Indian movable cap types. Provisions for solar heating of feed water, composting of effluent and attachments tomore » both latrine and animal shed were incorporated in the unit. The structural theory, design criteria, construction technique and cost estimation of the circular digester are described. Some operation and performance data of the circular digester are presented. This covers the effects of variation of ambient temperature on internal temperature, effects of temperature and pressure on the gas production rate and composition.« less

Constructive singularities and energy efficiency of St. Petersburg historic circuses

NASA Astrophysics Data System (ADS)

Sysoeva, Elena; Trushina, Ekaterina

2017-10-01

The article is devoted to the design and construction of St. Petersburg circuses during the period since 1822 till nowadays. The article presents the characteristics of all eight historic buildings of St. Petersburg and their structural and architectural features. The article raises some issues of energy-optimal shape of a building on the example of St. Petersburg modern circus building. There are several historical drawings and photographs of the circus buildings. The article includes overview of normative regulation of circus buildings in Russia since the middle of the twentieth century and prospects for the future.

National Program for Inspection of Non-Federal Dams. Baker Floodwater Reservoir Site 11 (NH 00478), NHWRB No. 249.13, Merrimack River Basin, Wentworth, New Hampshire. Phase I Inspection Report.

DTIC Science & Technology

1979-07-01

General 5-1 b. Design Data 5-1 c. Experience Data 5-1 d. Visual Observation 5-1 e. Overtopping Potential 5-1 f. Dam Failure Analysis 5-2 6. STRUCTURAL...the Soil Conservation Service, Durham, New Hampshire. The construction * contractor was Robie Construction Company , Inc. i. Normal Operating...INVENTORY OF DAMS P 0O - ... - SECTION 5 HYDROLOGY AND HYDRAULIC ANALYSIS • 5.1 Evaluation of Features a. General. Baker Dam Site 11 is an earthen

Construction and characterization of ultraviolet acousto-optic based femtosecond pulse shapers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mcgrane, Shawn D; Moore, David S; Greenfield, Margo T

2008-01-01

We present all the information necessary for construction and characterization of acousto optic pulse shapers, with a focus on ultraviolet wavelengths, Various radio-frequency drive configurations are presented to allow optimization via knowledgeable trade-off of design features. Detailed performance characteristics of a 267 nm acousto-optic modulator (AOM) based pulse shaper are presented, Practical considerations for AOM based pulse shaping of ultra-broad bandwidth (sub-10 fs) amplified femtosecond pulse shaping are described, with particular attention paid to the effects of the RF frequency bandwidth and optical frequency bandwidth on the spatial dispersion of the output laser pulses.

Examining Theory-Based Behavior-Change Constructs, Social Interaction, and Sociability Features of the Weight Watchers' Online Community

ERIC Educational Resources Information Center

Wang, Ye; Willis, Erin

2016-01-01

Objective: To examine whether and to what extent relevant and meaningful discussions of weight loss occurred in the Weight Watchers' online community, and whether and to what extent the online community is designed for fostering such discussions. Methods: A multimethod approach was used here. First, a quantitative content analysis was conducted on…

Three Dimensional Imaging with Multiple Wavelength Speckle Interferometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernacki, Bruce E.; Cannon, Bret D.; Schiffern, John T.

2014-05-28

We present the design, modeling, construction, and results of a three-dimensional imager based upon multiple-wavelength speckle interferometry. A surface under test is illuminated with tunable laser light in a Michelson interferometer configuration while a speckled image is acquired at each laser frequency step. The resulting hypercube is Fourier transformed in the frequency dimension and the beat frequencies that result map the relative offsets of surface features. Synthetic wavelengths resulting from the laser tuning can probe features ranging from 18 microns to hundreds of millimeters. Three dimensional images will be presented along with modeling results.

A survey of aerobraking orbital transfer vehicle design concepts

NASA Technical Reports Server (NTRS)

Park, Chul

1987-01-01

The five existing design concepts of the aerobraking orbital transfer vehicle (namely, the raked sphere-cone designs, conical lifting-brake, raked elliptic-cone, lifting-body, and ballute) are reviewed and critiqued. Historical backgrounds, and the geometrical, aerothermal, and operational features of these designs are reviewed first. Then, the technological requirements for the vehicle (namely, navigation, aerodynamic stability and control, afterbody flow impingement, nonequilibrium radiation, convective heat-transfer rates, mission abort and multiple atmospheric passes, transportation and construction, and the payload-to-vehicle weight requirements) are delineated by summarizing the recent advancements made on these issues. Each of the five designs are critiqued and rated on these issues. The highest and the lowest ratings are given to the raked sphere-cone and the ballute design, respectively.

Sandia National Laboratories Facilities Management and Operations Center Design Standards Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Timothy L.

2014-09-01

At Sandia National Laboratories in New Mexico (SNL/NM), the design, construction, operation, and maintenance of facilities is guided by industry standards, a graded approach, and the systematic analysis of life cycle benefits received for costs incurred. The design of the physical plant must ensure that the facilities are "fit for use," and provide conditions that effectively, efficiently, and safely support current and future mission needs. In addition, SNL/NM applies sustainable design principles, using an integrated whole-building design approach, from site planning to facility design, construction, and operation to ensure building resource efficiency and the health and productivity of occupants. Themore » safety and health of the workforce and the public, any possible effects on the environment, and compliance with building codes take precedence over project issues, such as performance, cost, and schedule. These design standards generally apply to all disciplines on all SNL/NM projects. Architectural and engineering design must be both functional and cost-effective. Facility design must be tailored to fit its intended function, while emphasizing low-maintenance, energy-efficient, and energy-conscious design. Design facilities that can be maintained easily, with readily accessible equipment areas, low maintenance, and quality systems. To promote an orderly and efficient appearance, architectural features of new facilities must complement and enhance the existing architecture at the site. As an Architectural and Engineering (A/E) professional, you must advise the Project Manager when this approach is prohibitively expensive. You are encouraged to use professional judgment and ingenuity to produce a coordinated interdisciplinary design that is cost-effective, easily contractible or buildable, high-performing, aesthetically pleasing, and compliant with applicable building codes. Close coordination and development of civil, landscape, structural, architectural, fire protection, mechanical, electrical, telecommunications, and security features is expected to ensure compatibility with planned functional equipment and to facilitate constructability. If portions of the design are subcontracted to specialists, delivery of the finished design documents must not be considered complete until the subcontracted portions are also submitted for review. You must, along with support consultants, perform functional analyses and programming in developing design solutions. These solutions must reflect coordination of the competing functional, budgetary, and physical requirements for the project. During design phases, meetings between you and the SNL/NM Project Team to discuss and resolve design issues are required. These meetings are a normal part of the design process. For specific design-review requirements, see the project-specific Design Criteria. In addition to the design requirements described in this manual, instructive information is provided to explain the sustainable building practice goals for design, construction, operation, and maintenance of SNL/NM facilities. Please notify SNL/NM personnel of design best practices not included in this manual, so they can be incorporated in future updates. You must convey all documents describing work to the SNL/NM Project Manager in both hard copy and in an electronic format compatible with the SNL/NM-prescribed CADD and other software packages, and in accordance with a SNL/NM approved standard format. Print all hard copy versions of submitted documents (excluding drawings and renderings) double-sided when practical.« less

Neuroimaging Study Designs, Computational Analyses and Data Provenance Using the LONI Pipeline

PubMed Central

Dinov, Ivo; Lozev, Kamen; Petrosyan, Petros; Liu, Zhizhong; Eggert, Paul; Pierce, Jonathan; Zamanyan, Alen; Chakrapani, Shruthi; Van Horn, John; Parker, D. Stott; Magsipoc, Rico; Leung, Kelvin; Gutman, Boris; Woods, Roger; Toga, Arthur

2010-01-01

Modern computational neuroscience employs diverse software tools and multidisciplinary expertise to analyze heterogeneous brain data. The classical problems of gathering meaningful data, fitting specific models, and discovering appropriate analysis and visualization tools give way to a new class of computational challenges—management of large and incongruous data, integration and interoperability of computational resources, and data provenance. We designed, implemented and validated a new paradigm for addressing these challenges in the neuroimaging field. Our solution is based on the LONI Pipeline environment [3], [4], a graphical workflow environment for constructing and executing complex data processing protocols. We developed study-design, database and visual language programming functionalities within the LONI Pipeline that enable the construction of complete, elaborate and robust graphical workflows for analyzing neuroimaging and other data. These workflows facilitate open sharing and communication of data and metadata, concrete processing protocols, result validation, and study replication among different investigators and research groups. The LONI Pipeline features include distributed grid-enabled infrastructure, virtualized execution environment, efficient integration, data provenance, validation and distribution of new computational tools, automated data format conversion, and an intuitive graphical user interface. We demonstrate the new LONI Pipeline features using large scale neuroimaging studies based on data from the International Consortium for Brain Mapping [5] and the Alzheimer's Disease Neuroimaging Initiative [6]. User guides, forums, instructions and downloads of the LONI Pipeline environment are available at http://pipeline.loni.ucla.edu. PMID:20927408

Implementation of a digital optical matrix-vector multiplier using a holographic look-up table and residue arithmetic

NASA Technical Reports Server (NTRS)

Habiby, Sarry F.

1987-01-01

The design and implementation of a digital (numerical) optical matrix-vector multiplier are presented. The objective is to demonstrate the operation of an optical processor designed to minimize computation time in performing a practical computing application. This is done by using the large array of processing elements in a Hughes liquid crystal light valve, and relying on the residue arithmetic representation, a holographic optical memory, and position coded optical look-up tables. In the design, all operations are performed in effectively one light valve response time regardless of matrix size. The features of the design allowing fast computation include the residue arithmetic representation, the mapping approach to computation, and the holographic memory. In addition, other features of the work include a practical light valve configuration for efficient polarization control, a model for recording multiple exposures in silver halides with equal reconstruction efficiency, and using light from an optical fiber for a reference beam source in constructing the hologram. The design can be extended to implement larger matrix arrays without increasing computation time.

Toolkits and Libraries for Deep Learning.

PubMed

Erickson, Bradley J; Korfiatis, Panagiotis; Akkus, Zeynettin; Kline, Timothy; Philbrick, Kenneth

2017-08-01

Deep learning is an important new area of machine learning which encompasses a wide range of neural network architectures designed to complete various tasks. In the medical imaging domain, example tasks include organ segmentation, lesion detection, and tumor classification. The most popular network architecture for deep learning for images is the convolutional neural network (CNN). Whereas traditional machine learning requires determination and calculation of features from which the algorithm learns, deep learning approaches learn the important features as well as the proper weighting of those features to make predictions for new data. In this paper, we will describe some of the libraries and tools that are available to aid in the construction and efficient execution of deep learning as applied to medical images.

LDRD final report :

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brost, Randolph C.; McLendon, William Clarence,

2013-01-01

Modeling geospatial information with semantic graphs enables search for sites of interest based on relationships between features, without requiring strong a priori models of feature shape or other intrinsic properties. Geospatial semantic graphs can be constructed from raw sensor data with suitable preprocessing to obtain a discretized representation. This report describes initial work toward extending geospatial semantic graphs to include temporal information, and initial results applying semantic graph techniques to SAR image data. We describe an efficient graph structure that includes geospatial and temporal information, which is designed to support simultaneous spatial and temporal search queries. We also report amore » preliminary implementation of feature recognition, semantic graph modeling, and graph search based on input SAR data. The report concludes with lessons learned and suggestions for future improvements.« less

Construction, Startup and Operation of a New LLRW Disposal Facility in Andrews County, Texas - 12151

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Vliet, James A.

2012-07-01

During this last year, Waste Control Specialists LLC (WCS) completed construction and achieved start of operations of a new low level radioactive waste (LLRW) disposal facility in Andrews County Texas. Disposal operations are underway for commercial LLRW, and start up evolutions are in progress for disposal of Department of Energy (DOE) LLRW. The overall approach to construction and start up are presented as well as some of the more significant challenges and how they were addressed to achieve initial operations of the first new commercial low level radioactive waste disposal facility in more than 30 years. The WCS disposal facilitymore » consists of two LLRW disposal cells, one for Texas Compact waste, and a separate disposal cell for DOE waste. Both disposal cells have very robust and unique designs. The cells themselves are constructed entirely in very low permeability red bed clay. The cell liners include a 0.91 meter thick clay liner meeting unprecedented permeability limits, 0.3 meter thick reinforced concrete barriers, as well as the standard geo-synthetic liners. Actions taken to meet performance criteria and install these liners will be discussed. Consistent with this highly protective landfill design, WCS chose to install a zero discharge site water management system. The considerations behind the design and construction of this system will be presented. Other activities essential to successful start of LLRW disposal operations included process and procedure development and refinement, staffing and staff development, and training. Mock ups were built and used for important evolutions and functions. Consistent with the extensive regulation of LLRW operations, engagement with the Texas Commission on Environmental Quality (TCEQ) was continuous and highly interactive. This included daily activity conference calls, weekly coordination calls and numerous topical conference calls and meetings. TCEQ staff and consultants frequently observed specific construction evolutions, such as geological feature mapping of designated excavation faces, disposal cell clay liner installation, disposal cell concrete barrier construction, etc. (author)« less

Citizens Utilities Company's successful residential new construction market transformation program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caulfield, T.O.; Shepherd, M.A.

1998-07-01

Citizens Utilities Company, Arizona Electric Division (CUC/AED) fielded a Residential New Construction Program (RNC) in the forth quarter of 1994 that had been designed from conception as a market transformation program. The CUC RNC Program encouraged builders to adopt energy efficient building practices for new homes by supplying builders estimates of energy savings, supplying inspections services to assist builders in applying energy efficient building practices while verifying compliance, and posting and promoting the home as energy efficient during the sales period. Measures generally required to qualify for the program were R-38 ceiling insulation, R-21 wall insulation, polysealing of all infiltrationmore » gaps during construction, well sealed air-conditioning ducts, and an air conditioner Seasonal Energy Efficiency Rating (SEER) of 11.0 or greater. In less than two years the program achieved over 17% market penetration without offering rebates to builders. This paper reviews the design of the program, including a discussion of the features felt to be primarily responsible for its success. It reviews the levels of penetration achieved, free-ridership, spillover, and market barriers encountered. Finally it proposes improvements to the program designed to carry it the next step toward a self-sustaining market transformation program.« less

Construction of Nanowire Heterojunctions: Photonic Function-Oriented Nanoarchitectonics.

PubMed

Li, Yong Jun; Yan, Yongli; Zhao, Yong Sheng; Yao, Jiannian

2016-02-10

Nanophotonics has received broad research interest because it may provide an alternative opportunity to overcome the fundamental limitations of electronic circuits. So far, diverse photonic functions, such as light generation, modulation, and detection, have been realized based on various nano-materials. The exact structural features of these material systems, including geometric characteristics, surface morphology, and material composition, play a key role in determining the photonic functions. Therefore, rational designs and constructions of materials on both morphological and componential levels, namely nanoarchitectonics, are indispensable for any photonic device with specific functionalities. Recently, a series of nanowire heterojunctions (NWHJs), which are usually made from two or more kinds of material compositions, were constructed for novel photonic applications based on various interactions between different materials at the junctions, for instance, energy transfer, exciton-plasmon coupling, or photon-plasmon coupling. A summary of these works is necessary to get a more comprehensive understanding of the relationship between photonic functions and architectonics of NWHJs, which will be instructive for designing novel photonic devices towards integrated circuits. Here, photonic function oriented nanoarchitectonics based on recent breakthroughs in nanophotonic devices are discussed, with emphasis on the design mechanisms, fabrication strategies, and excellent performances. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Large-scale feature searches of collections of medical imagery

NASA Astrophysics Data System (ADS)

Hedgcock, Marcus W.; Karshat, Walter B.; Levitt, Tod S.; Vosky, D. N.

1993-09-01

Large scale feature searches of accumulated collections of medical imagery are required for multiple purposes, including clinical studies, administrative planning, epidemiology, teaching, quality improvement, and research. To perform a feature search of large collections of medical imagery, one can either search text descriptors of the imagery in the collection (usually the interpretation), or (if the imagery is in digital format) the imagery itself. At our institution, text interpretations of medical imagery are all available in our VA Hospital Information System. These are downloaded daily into an off-line computer. The text descriptors of most medical imagery are usually formatted as free text, and so require a user friendly database search tool to make searches quick and easy for any user to design and execute. We are tailoring such a database search tool (Liveview), developed by one of the authors (Karshat). To further facilitate search construction, we are constructing (from our accumulated interpretation data) a dictionary of medical and radiological terms and synonyms. If the imagery database is digital, the imagery which the search discovers is easily retrieved from the computer archive. We describe our database search user interface, with examples, and compare the efficacy of computer assisted imagery searches from a clinical text database with manual searches. Our initial work on direct feature searches of digital medical imagery is outlined.

'You see?' Teaching and learning how to interpret visual cues during surgery.

PubMed

Cope, Alexandra C; Bezemer, Jeff; Kneebone, Roger; Lingard, Lorelei

2015-11-01

The ability to interpret visual cues is important in many medical specialties, including surgery, in which poor outcomes are largely attributable to errors of perception rather than poor motor skills. However, we know little about how trainee surgeons learn to make judgements in the visual domain. We explored how trainees learn visual cue interpretation in the operating room. A multiple case study design was used. Participants were postgraduate surgical trainees and their trainers. Data included observer field notes, and integrated video- and audio-recordings from 12 cases representing more than 11 hours of observation. A constant comparative methodology was used to identify dominant themes. Visual cue interpretation was a recurrent feature of trainer-trainee interactions and was achieved largely through the pedagogic mechanism of co-construction. Co-construction was a dialogic sequence between trainer and trainee in which they explored what they were looking at together to identify and name structures or pathology. Co-construction took two forms: 'guided co-construction', in which the trainer steered the trainee to see what the trainer was seeing, and 'authentic co-construction', in which neither trainer nor trainee appeared certain of what they were seeing and pieced together the information collaboratively. Whether the co-construction activity was guided or authentic appeared to be influenced by case difficulty and trainee seniority. Co-construction was shown to occur verbally, through discussion, and also through non-verbal exchanges in which gestures made with laparoscopic instruments contributed to the co-construction discourse. In the training setting, learning visual cue interpretation occurs in part through co-construction. Co-construction is a pedagogic phenomenon that is well recognised in the context of learning to interpret verbal information. In articulating the features of co-construction in the visual domain, this work enables the development of explicit pedagogic strategies for maximising trainees' learning of visual cue interpretation. This is relevant to multiple medical specialties in which judgements must be based on visual information. © 2015 John Wiley & Sons Ltd.

Supercritical carbon dioxide design strategies: from drug carriers to soft killers.

PubMed

Aguiar-Ricardo, Ana; Bonifácio, Vasco D B; Casimiro, Teresa; Correia, Vanessa G

2015-12-28

The integrated use of supercritical carbon dioxide (scCO(2)) and micro- and nanotechnologies has enabled new sustainable strategies for the manufacturing of new medications. 'Green' scCO(2)-based methodologies are well suited to improve either the synthesis or materials processing leading to the assembly of three-dimensional multifunctional constructs. By using scCO(2) either as C1 feedstock or as solvent, simple, economic, efficient and clean routes can be designed to synthesize materials with unique properties such as polyurea dendrimers and oxazoline-based polymers/oligomers. These new biocompatible, biodegradable and water-soluble polymeric materials can be engineered into multifunctional constructs with antimicrobial activity, targeting moieties, labelling units and/or efficiently loaded with therapeutics. This mini-review highlights the particular features exhibited by these materials resulting directly from the followed supercritical routes. © 2015 The Author(s).

The Wreck of the Pettu as an Example for Nineteenth Century Rural Shipbuilding in South-Western Finland

NASA Astrophysics Data System (ADS)

Auer, Jens; Ditta, Massimiliano

2016-08-01

Although the design and construction of wooden merchant vessels in the nineteenth century is generally considered to be well understood, the excavation and subsequent analysis of the wreck of the wooden Finnish topsail schooner Pettu (1865) revealed a number of unexpected features, which prompted the authors to take a closer look at the ship. In the following study, it will be attempted to gain an insight into the society that produced and used the merchant vessel through a detailed analysis of its construction and an investigation into the concept behind its design. The wreck of the Pettu, which, considering its loss in 1893, is barely covered by the 100 year rule in Danish heritage legislation, is a good example for the archaeological potential of even relatively `modern' wreck sites, adding to their significance.

Constructing complex graphics applications with CLIPS and the X window system

NASA Technical Reports Server (NTRS)

Faul, Ben M.

1990-01-01

This article will demonstrate how the artificial intelligence concepts in CLIPS used to solve problems encountered in the design and implementation of graphics applications within the UNIX-X Window System environment. The design of an extended version of CLIPS, called XCLIPS, is presented to show how the X Windows System graphics can be incorporated without losing DOS compatibility. Using XCLIPS, a sample scientific application is built that applies solving capabilities of both two and three dimensional graphics presentations in conjunction with the standard CLIPS features.

Self-propelled automatic chassis of Lunokhod-1: History of creation in episodes

NASA Astrophysics Data System (ADS)

Malenkov, Mikhail

2016-03-01

This report reviews the most important episodes in the history of designing the self-propelled automatic chassis of the first mobile extraterrestrial vehicle in the world, Lunokhod-1. The review considers the issues in designing moon rovers, their essential features, and the particular construction properties of their systems, mechanisms, units, and assemblies. It presents the results of exploiting the chassis of Lunokhod-1 and Lunokhod-2. Analysis of the approaches utilized and engineering solutions reveals their value as well as the consequences of certain defects.

Evaluating Callous-Unemotional Traits as a Personality Construct.

PubMed

Frick, Paul J; Ray, James V

2015-12-01

We evaluate the importance of callous-unemotional (CU) traits as a personality construct in isolation from other facets of psychopathy. Specifically, we review research suggesting that these traits are useful for designating a subgroup of youth with serious conduct problems who differ from other antisocial youth on important biological, emotional, cognitive, and social characteristics. In addition, the temperamental features related to CU traits are risk factors for impairments in conscience development in young children. Thus, these traits could advance theoretical models explaining the development of severe antisocial behavior and psychopathy. CU traits also have important clinical utility because they designate a particularly severe and impaired subgroup of antisocial youth, leading to their inclusion in the DSM-5. As a result of this inclusion in diagnostic classification, there has been an increased focus on how to best assess CU traits, and we discuss several key issues in their assessment, highlighting several limitations in existing measures. Finally, the increased use of CU traits, separately from other facets of psychopathy, makes it important to determine how these traits relate to other personality constructs. Thus, we examine how measures of CU traits relate to the broader construct of psychopathy and to other basic personality dimensions. © 2014 Wiley Periodicals, Inc.

The engineering design of the Tokamak Physics Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmidt, J.A.

A mission and supporting physics objectives have been developed, which establishes an important role for the Tokamak Physics Experiment (TPX) in developing the physic basis for a future fusion reactor. The design of TPX include advanced physics features, such as shaping and profile control, along with the capability of operating for very long pulses. The development of the superconducting magnets, actively cooled internal hardware, and remote maintenance will be an important technology contribution to future fusion projects, such as ITER. The Conceptual Design and Management Systems for TPX have been developed and reviewed, and the project is beginning Preliminary Design.more » If adequately funded the construction project should be completed in the year 2000.« less

Integrating Health Behavior Theory and Design Elements in Serious Games.

PubMed

Cheek, Colleen; Fleming, Theresa; Lucassen, Mathijs Fg; Bridgman, Heather; Stasiak, Karolina; Shepherd, Matthew; Orpin, Peter

2015-01-01

Internet interventions for improving health and well-being have the potential to reach many people and fill gaps in service provision. Serious gaming interfaces provide opportunities to optimize user adherence and impact. Health interventions based in theory and evidence and tailored to psychological constructs have been found to be more effective to promote behavior change. Defining the design elements which engage users and help them to meet their goals can contribute to better informed serious games. To elucidate design elements important in SPARX, a serious game for adolescents with depression, from a user-centered perspective. We proposed a model based on an established theory of health behavior change and practical features of serious game design to organize ideas and rationale. We analyzed data from 5 studies comprising a total of 22 focus groups and 66 semistructured interviews conducted with youth and families in New Zealand and Australia who had viewed or used SPARX. User perceptions of the game were applied to this framework. A coherent framework was established using the three constructs of self-determination theory (SDT), autonomy, competence, and relatedness, to organize user perceptions and design elements within four areas important in design: computer game, accessibility, working alliance, and learning in immersion. User perceptions mapped well to the framework, which may assist developers in understanding the context of user needs. By mapping these elements against the constructs of SDT, we were able to propose a sound theoretical base for the model. This study's method allowed for the articulation of design elements in a serious game from a user-centered perspective within a coherent overarching framework. The framework can be used to deliberately incorporate serious game design elements that support a user's sense of autonomy, competence, and relatedness, key constructs which have been found to mediate motivation at all stages of the change process. The resulting model introduces promising avenues for future exploration. Involving users in program design remains an imperative if serious games are to be fit for purpose.

Improvement of Steam Turbine Operational Performance and Reliability with using Modern Information Technologies

NASA Astrophysics Data System (ADS)

Brezgin, V. I.; Brodov, Yu M.; Kultishev, A. Yu

2017-11-01

The report presents improvement methods review in the fields of the steam turbine units design and operation based on modern information technologies application. In accordance with the life cycle methodology support, a conceptual model of the information support system during life cycle main stages (LC) of steam turbine unit is suggested. A classifying system, which ensures the creation of sustainable information links between the engineer team (manufacture’s plant) and customer organizations (power plants), is proposed. Within report, the principle of parameterization expansion beyond the geometric constructions at the design and improvement process of steam turbine unit equipment is proposed, studied and justified. The report presents the steam turbine unit equipment design methodology based on the brand new oil-cooler design system that have been developed and implemented by authors. This design system combines the construction subsystem, which is characterized by extensive usage of family tables and templates, and computation subsystem, which includes a methodology for the thermal-hydraulic zone-by-zone oil coolers design calculations. The report presents data about the developed software for operational monitoring, assessment of equipment parameters features as well as its implementation on five power plants.

Mechanical-Kinetic Modeling of a Molecular Walker from a Modular Design Principle

NASA Astrophysics Data System (ADS)

Hou, Ruizheng; Loh, Iong Ying; Li, Hongrong; Wang, Zhisong

2017-02-01

Artificial molecular walkers beyond burnt-bridge designs are complex nanomachines that potentially replicate biological walkers in mechanisms and functionalities. Improving the man-made walkers up to performance for widespread applications remains difficult, largely because their biomimetic design principles involve entangled kinetic and mechanical effects to complicate the link between a walker's construction and ultimate performance. Here, a synergic mechanical-kinetic model is developed for a recently reported DNA bipedal walker, which is based on a modular design principle, potentially enabling many directional walkers driven by a length-switching engine. The model reproduces the experimental data of the walker, and identifies its performance-limiting factors. The model also captures features common to the underlying design principle, including counterintuitive performance-construction relations that are explained by detailed balance, entropy production, and bias cancellation. While indicating a low directional fidelity for the present walker, the model suggests the possibility of improving the fidelity above 90% by a more powerful engine, which may be an improved version of the present engine or an entirely new engine motif, thanks to the flexible design principle. The model is readily adaptable to aid these experimental developments towards high-performance molecular walkers.

Hierarchical Structure of Articular Bone-Cartilage Interface and Its Potential Application for Osteochondral Tissue Engineering

NASA Astrophysics Data System (ADS)

Bian, Weiguo; Qin, Lian; Li, Dichen; Wang, Jin; Jin, Zhongmin

2010-09-01

The artificial biodegradable osteochondral construct is one of mostly promising lifetime substitute in the joint replacement. And the complex hierarchical structure of natural joint is important in developing the osteochondral construct. However, the architecture features of the interface between cartilage and bone, in particular those at the micro-and nano-structural level, remain poorly understood. This paper investigates these structural data of the cartilage-bone interface by micro computerized tomography (μCT) and Scanning Electron Microscope (SEM). The result of μCT shows that important bone parameters and the density of articular cartilage are all related to the position in the hierarchical structure. The conjunctions of bone and cartilage were defined by SEM. All of the study results would be useful for the design of osteochondral construct further manufactured by nano-tech. A three-dimensional model with gradient porous structure is constructed in the environment of Pro/ENGINEERING software.

Tongonani geothermal power development, Philippines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minson, A.A.C.; Fry, T.J.; Kivell, J.A.

1985-01-01

This paper describes the features, design and construction of a 112 MWe geothermal power project, representing the first stage development of the substantial geothermal resources of the central Philippine region. The project has been undertaken by the Philippine Government. The National Powe Corporation is responsible for generation and distribution facilities and the Philippine National Oil Company Energy Development Corporation is responsible for controlled delivery of steam to the powe station.

Architecture of high-rise buildings as a brand of the modern Kazakhstan

NASA Astrophysics Data System (ADS)

Abdrassilova, Gulnara; Kozbagarova, Nina; Tuyakayeva, Ainagul

2018-03-01

Using practical examples article reviews urban-planning and space-planning features of design and construction of high-rise buildings in Kazakhstan conditions; methods are identified that provide for structural stability against wind and seismic loads based on innovative technical and technological solutions. Article authors stress out the fashion function of high-rise buildings in the new capital of Kazakhstan, the Astana city.

Separator-spacer for electrochemical systems

DOEpatents

Grimes, Patrick G.; Einstein, Harry; Newby, Kenneth R.; Bellows, Richard J.

1983-08-02

An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

Sheet electrode for electrochemical systems

DOEpatents

Tsien, Hsue C.; Newby, Kenneth R.; Grimes, Patrick G.; Bellows, Richard J.

1983-04-12

An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

Shale embankment construction criteria : experimental feature interim report.

DOT National Transportation Integrated Search

1985-06-01

The research was conducted in the summer of 1983 during the realignment construction of the Mystic Creek - Camas Valley section on the Coos Bay - Roseburg Highway. Construction is still in progress. As outlined in the experimental features work plan ...

Use of the rectus abdominis muscle for abdominal stoma sphincter construction: an anatomical feasibility study.

PubMed

Bardoel, J W; Stadelmann, W K; Tobin, G R; Werker, P M; Stremel, R W; Kon, M; Barker, J H

2000-02-01

Permanent fecal abdominal stomas significantly decrease quality of life. Previous attempts to create continent stomas by using dynamic myoplasty procedures have resulted in disappointing outcomes, primarily owing to denervation atrophy of the muscle flap that was used in the creation of the sphincter and because of muscle fatigue resulting from continuous electrical stimulation that is received by the flap to force contraction. On the basis of these problems, we designed two separate studies: an anatomical study addressing flap denervation and a functional study addressing muscle fatigue. The present study addresses the first topic and was designed to develop a rectus abdominis muscle flap into a sphincter that was anatomically situated to create a stoma while preserving as much innervation as possible. In 24 rectus abdominis muscles of human cadavers, the neurovascular anatomy was defined, then the anatomical feasibility of two different muscle flap configurations was considered. The flaps investigated were the peninsula flap and island flap designs, with both using the most caudal segment of the rectus abdominis muscle in construction of the sphincter. Neither flap design required the killing of a nerve for stoma sphincter creation, resulting in minimal muscle denervation. The conclusion of our comparison was that the above, in conjunction with other features of the island flap design, such as muscle overlap after sphincter formation and abdominal wall positioning of the sphincter, made the island flap design better suited to stoma sphincter construction.

Integrated Approach to Industrial Packaging Design

NASA Astrophysics Data System (ADS)

Vorobeva, O.

2017-11-01

The article reviews studies in the field of industrial packaging design. The major factors which influence technological, ergonomic, economic and ecological features of packaging are established. The main modern trends in packaging design are defined, the principles of marketing communications and their influence on consumers’ consciousness are indicated, and the function of packaging as a transmitter of brand values is specified. Peculiarities of packaging technology and printing techniques in modern printing industry are considered. The role of designers in the stage-by-stage development of the construction, form and graphic design concept of packaging is defined. The examples of authentic packaging are given and the mention of the tetrahedron packaging history is made. At the end of the article, conclusions on the key research aspects are made.

Design and Fabrication of the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Kozub, Thomas; Majeski, Richard; Kaita, Robert; Priniski, Craig; Zakharov, Leonid

2006-10-01

The design objective of the lithium tokamak experiment (LTX) is to investigate the equilibrium and stability of tokamak discharges with near-zero recycling. The construction of LTX incorporates the conversion of the existing current drive experiment (CDX) vessel into one with a nearly complete plasma facing surface of liquid lithium This paper will describe the design, fabrication, and installation activities required to convert CDX into LTX. The most significant new feature is the addition of a plasma facing liner on a shell that will be operated at 300 C to 400 C and covered with an evaporated layer of liquid lithium. The shell has been fabricated in-house from explosively bonded stainless steel on copper to a rather unique geometry to match the outer flux surface. Other significant device modifications include the construction of a new ohmic heating power system, rebuilding of the vacuum vessel, new lithium evaporators, additional diagnostics, modifications to the poloidal field coil geometry and their associated power supplies. Details on the progress of this conversion will be reported.

Practical calibration of design data to technical capabilities of horizontal directional drilling rig

NASA Astrophysics Data System (ADS)

Toropov, S. Yu; Toropov, V. S.

2018-05-01

In order to design more accurately trenchless pipeline passages, a technique has been developed for calculating the passage profile, based on specific parameters of the horizontal directional drilling rig, including the range of possible drilling angles and a list of compatible drill pipe sets. The algorithm for calculating the parameters of the trenchless passage profile is shown in the paper. This algorithm is based on taking into account the features of HDD technology, namely, three different stages of production. The authors take into account that the passage profile is formed at the first stage of passage construction, that is, when drilling a pilot well. The algorithm involves calculating the profile by taking into account parameters of the drill pipes used and angles of their deviation relative to each other during the pilot drilling. This approach allows us to unambiguously calibrate the designed profile for the HDD rig capabilities and the auxiliary and navigation equipment used in the construction process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, Karla

Although the high-performance computing (HPC) community increasingly embraces object-oriented programming (OOP), most HPC OOP projects employ the C++ programming language. Until recently, Fortran programmers interested in mining the benefits of OOP had to emulate OOP in Fortran 90/95. The advent of widespread compiler support for Fortran 2003 now facilitates explicitly constructing object-oriented class hierarchies via inheritance and leveraging related class behaviors such as dynamic polymorphism. Although C++ allows a class to inherit from multiple parent classes, Fortran and several other OOP languages restrict or prohibit explicit multiple inheritance relationships in order to circumvent several pitfalls associated with them. Nonetheless, whatmore » appears as an intrinsic feature in one language can be modeled as a user-constructed design pattern in another language. The present paper demonstrates how to apply the facade structural design pattern to support a multiple inheritance class relationship in Fortran 2003. As a result, the design unleashes the power of the associated class relationships for modeling complicated data structures yet avoids the ambiguities that plague some multiple inheritance scenarios.« less

Evaluating Measurement of Dynamic Constructs: Defining a Measurement Model of Derivatives

PubMed Central

Estabrook, Ryne

2015-01-01

While measurement evaluation has been embraced as an important step in psychological research, evaluating measurement structures with longitudinal data is fraught with limitations. This paper defines and tests a measurement model of derivatives (MMOD), which is designed to assess the measurement structure of latent constructs both for analyses of between-person differences and for the analysis of change. Simulation results indicate that MMOD outperforms existing models for multivariate analysis and provides equivalent fit to data generation models. Additional simulations show MMOD capable of detecting differences in between-person and within-person factor structures. Model features, applications and future directions are discussed. PMID:24364383

Design features to enhance external hip protector adherence in the nursing home setting.

PubMed

Honkanen, Lisa A; Dehner, Melissa L; Lachs, Mark S

2006-11-01

To determine the preferences for external hip protector (EHP) design features of both certified nursing assistants (CNAs) and nursing home laundry personnel, and to test the durability of favored model features. Cross-sectional descriptive study of CNAs' and laundry personnels' preferences and a prospective experimental study of EHP fastener durability under institutional laundry conditions. Three urban nursing homes and a hospital-based laundry service. Twenty-seven CNAs, 4 laundry service supervisors. Five focus groups with CNAs and a survey of laundry supervisors were conducted to elicit preferences of EHP design features with an emphasis on convenience and durability. A laundry test of 20 EHPs was conducted to compare these design features. There was wide agreement among CNAs and laundry personnel that EHPs with soft pads in garments of light neutral colors, and cotton-blend fabrics were most preferred. CNAs preferred sewn-in pads to removeable ones, but laundry personnel had no consensus on this issue. For dependent residents, wraparound (front opening) garments using Velcro were preferred by CNAs, whereas laundry supervisors preferred snap closures. When EHP underwent repeated washing in the laundry test, Velcro and snaps were functionally comparable at 52 cycles. Garments constructed of heavyweight cotton blends, polyester, or cotton with spandex maintained elasticity at 52 weeks, whereas the lightweight cotton blend stretched significantly. Based on CNAs' preferences, laundry personnels' input, and a laundry test, EHP design features that could enhance both caregiver efficiency and resident comfort include soft pads sewn into a light-colored (but non-white) heavier weight cotton-blend garment, with the availability of both a pull-up style and a wraparound style using Velcro fasteners. Snaps did not demonstrate superior durability in the laundry test, but further comparison with Velcro under clinical conditions is indicated. Education and inclusion of CNAs in EHP decision making are important ways to improve EHP adherence.

Liner-less Tanks for Space Application - Design and Manufacturing Considerations

NASA Technical Reports Server (NTRS)

Jones, Brian H.; Li, Min-Chung

2003-01-01

Composite pressure vessels, used extensively for gas and fuel containment in space vehicles, are generally constructed with a metallic liner, while the fiber reinforcement carries the major portion of the pressure-induced load. The design is dominated by the liner s low strain at yield since the reinforcing fibers cannot operate at their potential load-bearing capability without resorting to pre-stressing (or autofrettaging). An ultra high-efficiency pressure vessel, which operates at the optimum strain capability of the fibers, can be potentially achieved with a liner-less construction. This paper discusses the design and manufacturing challenges to be overcome in the development of such a pressure vessel. These include: (1) gas/liquid containment and permeation, (2) design and structural analysis, and (3) manufacturing process development. The paper also presents the development and validation tests on a liner-less pressure vessel developed by Kaiser Compositek Inc. (KCI). It should be noted that KCI s liner-less tank exhibits a highly controlled leak-before-burst mode. This feature results in a structure having the highest level of safety.

Identifying Facilitators and Barriers for Patient Safety in a Medicine Label Design System Using Patient Simulation and Interviews.

PubMed

Dieckmann, Peter; Clemmensen, Marianne Hald; Sørensen, Trine Kart; Kunstek, Pina; Hellebek, Annemarie

2016-12-01

Medicine label design plays an important role in improving patient safety. This study aimed at identifying facilitators and barriers in a medicine label system to prevent medication errors in clinical use by health care professionals. The study design is qualitative and exploratory, with a convenience sample of 10 nurses and 10 physicians from different acute care specialties working in hospitals in the Capital Region of Denmark. In 2 patient simulation scenarios and a sorting task, the participants selected the medicines from a range of ampules, vials, and infusion bags. After each scenario and in the end of the study, the participants were interviewed. Notes were validated with the participants, and content was analyzed. The label design benefited from the standardized construction of the labels, the clear layout and font, and some warning signs. The complexity of the system and some inconsistencies (different meaning of colors) posed challenges, when considered with the actual application context, in which there is little time to get familiar with the design features. For optimizing medicine labels and obtaining the full benefit of label design features on patient safety, it is necessary to consider the context in which they are used.

Feature selection gait-based gender classification under different circumstances

NASA Astrophysics Data System (ADS)

Sabir, Azhin; Al-Jawad, Naseer; Jassim, Sabah

2014-05-01

This paper proposes a gender classification based on human gait features and investigates the problem of two variations: clothing (wearing coats) and carrying bag condition as addition to the normal gait sequence. The feature vectors in the proposed system are constructed after applying wavelet transform. Three different sets of feature are proposed in this method. First, Spatio-temporal distance that is dealing with the distance of different parts of the human body (like feet, knees, hand, Human Height and shoulder) during one gait cycle. The second and third feature sets are constructed from approximation and non-approximation coefficient of human body respectively. To extract these two sets of feature we divided the human body into two parts, upper and lower body part, based on the golden ratio proportion. In this paper, we have adopted a statistical method for constructing the feature vector from the above sets. The dimension of the constructed feature vector is reduced based on the Fisher score as a feature selection method to optimize their discriminating significance. Finally k-Nearest Neighbor is applied as a classification method. Experimental results demonstrate that our approach is providing more realistic scenario and relatively better performance compared with the existing approaches.

Design of an Adaptive Human-Machine System Based on Dynamical Pattern Recognition of Cognitive Task-Load.

PubMed

Zhang, Jianhua; Yin, Zhong; Wang, Rubin

2017-01-01

This paper developed a cognitive task-load (CTL) classification algorithm and allocation strategy to sustain the optimal operator CTL levels over time in safety-critical human-machine integrated systems. An adaptive human-machine system is designed based on a non-linear dynamic CTL classifier, which maps a set of electroencephalogram (EEG) and electrocardiogram (ECG) related features to a few CTL classes. The least-squares support vector machine (LSSVM) is used as dynamic pattern classifier. A series of electrophysiological and performance data acquisition experiments were performed on seven volunteer participants under a simulated process control task environment. The participant-specific dynamic LSSVM model is constructed to classify the instantaneous CTL into five classes at each time instant. The initial feature set, comprising 56 EEG and ECG related features, is reduced to a set of 12 salient features (including 11 EEG-related features) by using the locality preserving projection (LPP) technique. An overall correct classification rate of about 80% is achieved for the 5-class CTL classification problem. Then the predicted CTL is used to adaptively allocate the number of process control tasks between operator and computer-based controller. Simulation results showed that the overall performance of the human-machine system can be improved by using the adaptive automation strategy proposed.

Development of the WTS-4 wind turbine design

NASA Astrophysics Data System (ADS)

Hasbrouck, T. M.; Divalentin, E.

Design features, developmental aspects, and financial projections for the WTS-4 4 MW wind turbine are presented. The WTS-4 is a horizontal axis, downwind, two-bladed, variable pitch machine. Start-up is at 7 m/s, rated power is reached at 15 m/s, and shut-down is set at 27 m/s, with all controls operating in a stand-alone mode by means of microprocessors. Each blade is 125 ft long, constructed of filament wound fiberglass reinforced epoxy, and attached at the root to a teetered steel alloy hub, which compensates for the shear caused by the tower shadow. Pitch is controlled by an electrohydraulic mechanism, and can be effected at a rate of 5 deg/s. Details of the nacelle components and costruction are provided, together with features of the system controller and design trade-offs. Cost comparisons with utility scale coal and oil baseload generation plants indicate that wind turbines will become cost competitive by 1985 and are favored thereafter.

Poster - Thur Eve - 48: An inexpensive and convenient phantom for quality assurance in image guidance based radiosurgery.

PubMed

Soisson, E

2012-07-01

This work describes the design and use of an inexpensive phantom designed for precision measurements in radiosurgery quality assurance. The main features of this simple phantom include its solid water construction, interchangeable ion chamber holders and film registration system, thus allowing for measurement of small fields with several detectors using the same phantom. The entire phantom was constructed using one 30cm × 30cm × 3cm slab of solid water. The phantom contains a slot that allows for the placement of two small volume ion chambers (liquid and A1SL) via custom inserts near the center of the phantom. In addition, the plug can be filled for film measurements. The phantom can be split down the center to allow for the placement of a film. As opposed to registering film to room based markers, such as lasers, the phantom contains radio-opaque fiducials that puncture the film while also providing a method to register the film images to exported dose planes. In addition to the markers used for film registration, the phantom contains several external beebees that can be used to avoid ambiguity in image registration when using image guidance for setup. This simple phantom contains many features of other much more expensive phantoms designed for this purpose and has been found to be very useful clinically and in departmental research. The key elements of this phantom could be included in several other designs allowing it to be reproduced in other centers. © 2012 American Association of Physicists in Medicine.

Feature-opinion pair identification of product reviews in Chinese: a domain ontology modeling method

NASA Astrophysics Data System (ADS)

Yin, Pei; Wang, Hongwei; Guo, Kaiqiang

2013-03-01

With the emergence of the new economy based on social media, a great amount of consumer feedback on particular products are conveyed through wide-spreading product online reviews, making opinion mining a growing interest for both academia and industry. According to the characteristic mode of expression in Chinese, this research proposes an ontology-based linguistic model to identify the basic appraisal expression in Chinese product reviews-"feature-opinion pair (FOP)." The product-oriented domain ontology is constructed automatically at first, then algorithms to identify FOP are designed by mapping product features and opinions to the conceptual space of the domain ontology, and finally comparative experiments are conducted to evaluate the model. Experimental results indicate that the performance of the proposed approach in this paper is efficient in obtaining a more accurate result compared to the state-of-art algorithms. Furthermore, through identifying and analyzing FOPs, the unstructured product reviews are converted into structured and machine-sensible expression, which provides valuable information for business application. This paper contributes to the related research in opinion mining by developing a solid foundation for further sentiment analysis at a fine-grained level and proposing a general way for automatic ontology construction.

A Content-Addressable Memory structure using quantum cells in nanotechnology with energy dissipation analysis

NASA Astrophysics Data System (ADS)

Sadoghifar, Ali; Heikalabad, Saeed Rasouli

2018-05-01

Quantum-dot cellular automata is one of the recent new technologies at the nanoscale that can be a suitable replacement for CMOS technology. The circuits constructed in QCA technology have desirable features such as low power consumption, high speed and small size. These features can be more distinct in memory structures. In this paper, we design a new structure for content addressable memory cell in QCA. For this purpose, first, a unique gate is introduced for mask operation in QCA and then this gate is used to improve the performance of CAM. These structures are evaluated with QCADesigner simulator.

Rapid Construction of a Benzo-Fused Indoxamycin Core Enabled by Site-Selective C-H Functionalizations.

PubMed

Bedell, T Aaron; Hone, Graham A B; Valette, Damien; Yu, Jin-Quan; Davies, Huw M L; Sorensen, Erik J

2016-07-11

Methods for functionalizing carbon-hydrogen bonds are featured in a new synthesis of the tricyclic core architecture that characterizes the indoxamycin family of secondary metabolites. A unique collaboration between three laboratories has engendered a design for synthesis featuring two sequential C-H functionalization reactions, namely a diastereoselective dirhodium carbene insertion followed by an ester-directed oxidative Heck cyclization, to rapidly assemble the congested tricyclic core of the indoxamycins. This project exemplifies how multi-laboratory collaborations can foster conceptually novel approaches to challenging problems in chemical synthesis. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Transforming AdaPT to Ada

NASA Technical Reports Server (NTRS)

Goldsack, Stephen J.; Holzbach-Valero, A. A.; Waldrop, Raymond S.; Volz, Richard A.

1991-01-01

This paper describes how the main features of the proposed Ada language extensions intended to support distribution, and offered as possible solutions for Ada9X can be implemented by transformation into standard Ada83. We start by summarizing the features proposed in a paper (Gargaro et al, 1990) which constitutes the definition of the extensions. For convenience we have called the language in its modified form AdaPT which might be interpreted as Ada with partitions. These features were carefully chosen to provide support for the construction of executable modules for execution in nodes of a network of loosely coupled computers, but flexibly configurable for different network architectures and for recovery following failure, or adapting to mode changes. The intention in their design was to provide extensions which would not impact adversely on the normal use of Ada, and would fit well in style and feel with the existing standard. We begin by summarizing the features introduced in AdaPT.

Probabilistic graphlet transfer for photo cropping.

PubMed

Zhang, Luming; Song, Mingli; Zhao, Qi; Liu, Xiao; Bu, Jiajun; Chen, Chun

2013-02-01

As one of the most basic photo manipulation processes, photo cropping is widely used in the printing, graphic design, and photography industries. In this paper, we introduce graphlets (i.e., small connected subgraphs) to represent a photo's aesthetic features, and propose a probabilistic model to transfer aesthetic features from the training photo onto the cropped photo. In particular, by segmenting each photo into a set of regions, we construct a region adjacency graph (RAG) to represent the global aesthetic feature of each photo. Graphlets are then extracted from the RAGs, and these graphlets capture the local aesthetic features of the photos. Finally, we cast photo cropping as a candidate-searching procedure on the basis of a probabilistic model, and infer the parameters of the cropped photos using Gibbs sampling. The proposed method is fully automatic. Subjective evaluations have shown that it is preferred over a number of existing approaches.

Protein location prediction using atomic composition and global features of the amino acid sequence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cherian, Betsy Sheena, E-mail: betsy.skb@gmail.com; Nair, Achuthsankar S.

2010-01-22

Subcellular location of protein is constructive information in determining its function, screening for drug candidates, vaccine design, annotation of gene products and in selecting relevant proteins for further studies. Computational prediction of subcellular localization deals with predicting the location of a protein from its amino acid sequence. For a computational localization prediction method to be more accurate, it should exploit all possible relevant biological features that contribute to the subcellular localization. In this work, we extracted the biological features from the full length protein sequence to incorporate more biological information. A new biological feature, distribution of atomic composition is effectivelymore » used with, multiple physiochemical properties, amino acid composition, three part amino acid composition, and sequence similarity for predicting the subcellular location of the protein. Support Vector Machines are designed for four modules and prediction is made by a weighted voting system. Our system makes prediction with an accuracy of 100, 82.47, 88.81 for self-consistency test, jackknife test and independent data test respectively. Our results provide evidence that the prediction based on the biological features derived from the full length amino acid sequence gives better accuracy than those derived from N-terminal alone. Considering the features as a distribution within the entire sequence will bring out underlying property distribution to a greater detail to enhance the prediction accuracy.« less

Investigation of HV/HR-CMOS technology for the ATLAS Phase-II Strip Tracker Upgrade

NASA Astrophysics Data System (ADS)

Fadeyev, V.; Galloway, Z.; Grabas, H.; Grillo, A. A.; Liang, Z.; Martinez-Mckinney, F.; Seiden, A.; Volk, J.; Affolder, A.; Buckland, M.; Meng, L.; Arndt, K.; Bortoletto, D.; Huffman, T.; John, J.; McMahon, S.; Nickerson, R.; Phillips, P.; Plackett, R.; Shipsey, I.; Vigani, L.; Bates, R.; Blue, A.; Buttar, C.; Kanisauskas, K.; Maneuski, D.; Benoit, M.; Di Bello, F.; Caragiulo, P.; Dragone, A.; Grenier, P.; Kenney, C.; Rubbo, F.; Segal, J.; Su, D.; Tamma, C.; Das, D.; Dopke, J.; Turchetta, R.; Wilson, F.; Worm, S.; Ehrler, F.; Peric, I.; Gregor, I. M.; Stanitzki, M.; Hoeferkamp, M.; Seidel, S.; Hommels, L. B. A.; Kramberger, G.; Mandić, I.; Mikuž, M.; Muenstermann, D.; Wang, R.; Zhang, J.; Warren, M.; Song, W.; Xiu, Q.; Zhu, H.

2016-09-01

ATLAS has formed strip CMOS project to study the use of CMOS MAPS devices as silicon strip sensors for the Phase-II Strip Tracker Upgrade. This choice of sensors promises several advantages over the conventional baseline design, such as better resolution, less material in the tracking volume, and faster construction speed. At the same time, many design features of the sensors are driven by the requirement of minimizing the impact on the rest of the detector. Hence the target devices feature long pixels which are grouped to form a virtual strip with binary-encoded z position. The key performance aspects are radiation hardness compatibility with HL-LHC environment, as well as extraction of the full hit position with full-reticle readout architecture. To date, several test chips have been submitted using two different CMOS technologies. The AMS 350 nm is a high voltage CMOS process (HV-CMOS), that features the sensor bias of up to 120 V. The TowerJazz 180 nm high resistivity CMOS process (HR-CMOS) uses a high resistivity epitaxial layer to provide the depletion region on top of the substrate. We have evaluated passive pixel performance, and charge collection projections. The results strongly support the radiation tolerance of these devices to radiation dose of the HL-LHC in the strip tracker region. We also describe design features for the next chip submission that are motivated by our technology evaluation.

Fabrication and testing of silver-hydrogen cells

NASA Technical Reports Server (NTRS)

Debicarri, D. J.; Charkey, A.

1978-01-01

Silver electrodes containing various additives were fabricated and tested in single electrode cells in order to improve the electrochemical utilization of sintered silver cathodes in Ag-H2 aerospace batteries. A standard stack arrangement was used which featured a NASA-developed organic-inorganic separator. All cells were cycled in a regime designed to remove 75% of the cells nominal capacity based on 3.3 gms/AHr Ag utilization. In cases where performance degradation was observed, the main feature mode appeared to be corrosion of either the expanded silver current collector or the connection between the silver electrode and the electrode tab. Promising silver electrodes from single electrode studies were used in the construction of 35 AHr Ag-H2 cells. Two such cells were constructed and installed in heavy walled pressure vessels for testing. Based on the data obtained from all cells tested during the program, four lightweight 35 AHr cells were fabricated. During acceptance testing these cells yielded an average gravimetric energy density of 30 WHr/1b.

Comparison of ion coupling strategies for a microengineered quadrupole mass filter.

PubMed

Wright, Steven; Syms, Richard R A; O'Prey, Shane; Hong, Guodong; Holmes, Andrew S

2009-01-01

The limitations of conventional machining and assembly techniques require that designs for quadrupole mass analyzers with rod diameters less than a millimeter are not merely scale versions of larger instruments. We show how silicon planar processing techniques and microelectromechanical systems (MEMS) design concepts can be used to incorporate complex features into the construction of a miniature quadrupole mass filter chip that could not easily be achieved using other microengineering approaches. Three designs for the entrance and exit to the filter consistent with the chosen materials and techniques have been evaluated. The differences between these seemingly similar structures have a significant effect on the performance. Although one of the designs results in severe attenuation of transmission with increasing mass, the other two can be scanned to m/z = 400 without any corruption of the mass spectrum. At m/z = 219, the variation in the transmission of the three designs was found to be approximately four orders of magnitude. A maximum resolution of M/DeltaM = 87 at 10% peak height has been achieved at m/z = 219 with a filter operated at 6 MHz and constructed using rods measuring (508 +/- 5) microm in diameter.

A next generation, pilot-scale continuous sterilization system for fermentation media

PubMed Central

Lester, M.; Brix, T.; Wong, D.; Nuechterlein, J.

2006-01-01

A new continuous sterilization system was designed, constructed, started up, and qualified for media sterilization for secondary metabolite cultivations, bioconversions, and enzyme production. An existing Honeywell Total Distributed Control 3000-based control system was extended using redundant High performance Process Manager controllers for 98 I/O (input/output) points. This new equipment was retrofitted into an industrial research fermentation pilot plant, designed and constructed in the early 1980s. Design strategies of this new continuous sterilizer system and the expanded control system are described and compared with the literature (including dairy and bio-waste inactivation applications) and the weaknesses of the prior installation for expected effectiveness. In addition, the reasoning behind selection of some of these improved features has been incorporated. Examples of enhancements adopted include sanitary heat exchanger (HEX) design, incorporation of a “flash” cooling HEX, on-line calculation of Fo and Ro, and use of field I/O modules located near the vessel to permit low-cost addition of new instrumentation. Sterilizer performance also was characterized over the expected range of operating conditions. Differences between design and observed temperature, pressure, and other profiles were quantified and investigated. PMID:16496186

Innovation in nanomedicine through materials nanoarchitectonics.

PubMed

Kujawa, Piotr; Winnik, Françoise M

2013-06-18

Materials nanoarchitectonics has led to important innovations in the design and construction of systems in nanoelectronics, nanomachinery, and energy conversion. Recent publications point to the fact that the same approach may be applied successfully to other fields. In this Perspective, we define the key features of materials nanoarchitectonics and examine how they can be used to address current challenges in nanomedicine, placing emphasis on colloidal agents for therapeutic and diagnostic applications.

A common feature pharmacophore for FDA-approved drugs inhibiting the Ebola virus.

PubMed

Ekins, Sean; Freundlich, Joel S; Coffee, Megan

2014-01-01

We are currently faced with a global infectious disease crisis which has been anticipated for decades. While many promising biotherapeutics are being tested, the search for a small molecule has yet to deliver an approved drug or therapeutic for the Ebola or similar filoviruses that cause haemorrhagic fever. Two recent high throughput screens published in 2013 did however identify several hits that progressed to animal studies that are FDA approved drugs used for other indications. The current computational analysis uses these molecules from two different structural classes to construct a common features pharmacophore. This ligand-based pharmacophore implicates a possible common target or mechanism that could be further explored. A recent structure based design project yielded nine co-crystal structures of pyrrolidinone inhibitors bound to the viral protein 35 (VP35). When receptor-ligand pharmacophores based on the analogs of these molecules and the protein structures were constructed, the molecular features partially overlapped with the common features of solely ligand-based pharmacophore models based on FDA approved drugs. These previously identified FDA approved drugs with activity against Ebola were therefore docked into this protein. The antimalarials chloroquine and amodiaquine docked favorably in VP35. We propose that these drugs identified to date as inhibitors of the Ebola virus may be targeting VP35. These computational models may provide preliminary insights into the molecular features that are responsible for their activity against Ebola virus in vitro and in vivo and we propose that this hypothesis could be readily tested.

A common feature pharmacophore for FDA-approved drugs inhibiting the Ebola virus

PubMed Central

Ekins, Sean; Freundlich, Joel S.; Coffee, Megan

2014-01-01

We are currently faced with a global infectious disease crisis which has been anticipated for decades. While many promising biotherapeutics are being tested, the search for a small molecule has yet to deliver an approved drug or therapeutic for the Ebola or similar filoviruses that cause haemorrhagic fever. Two recent high throughput screens published in 2013 did however identify several hits that progressed to animal studies that are FDA approved drugs used for other indications. The current computational analysis uses these molecules from two different structural classes to construct a common features pharmacophore. This ligand-based pharmacophore implicates a possible common target or mechanism that could be further explored. A recent structure based design project yielded nine co-crystal structures of pyrrolidinone inhibitors bound to the viral protein 35 (VP35). When receptor-ligand pharmacophores based on the analogs of these molecules and the protein structures were constructed, the molecular features partially overlapped with the common features of solely ligand-based pharmacophore models based on FDA approved drugs. These previously identified FDA approved drugs with activity against Ebola were therefore docked into this protein. The antimalarials chloroquine and amodiaquine docked favorably in VP35. We propose that these drugs identified to date as inhibitors of the Ebola virus may be targeting VP35. These computational models may provide preliminary insights into the molecular features that are responsible for their activity against Ebola virus in vitro and in vivo and we propose that this hypothesis could be readily tested. PMID:25653841

Physicochemically Tunable Polyfunctionalized RNA Square Architecture with Fluorogenic and Ribozymatic Properties

PubMed Central

2015-01-01

Recent advances in RNA nanotechnology allow the rational design of various nanoarchitectures. Previous methods utilized conserved angles from natural RNA motifs to form geometries with specific sizes. However, the feasibility of producing RNA architecture with variable sizes using native motifs featuring fixed sizes and angles is limited. It would be advantageous to display RNA nanoparticles of diverse shape and size derived from a given primary sequence. Here, we report an approach to construct RNA nanoparticles with tunable size and stability. Multifunctional RNA squares with a 90° angle were constructed by tuning the 60° angle of the three-way junction (3WJ) motif from the packaging RNA (pRNA) of the bacteriophage phi29 DNA packaging motor. The physicochemical properties and size of the RNA square were also easily tuned by modulating the “core” strand and adjusting the length of the sides of the square via predictable design. Squares of 5, 10, and 20 nm were constructed, each showing diverse thermodynamic and chemical stabilities. Four “arms” extending from the corners of the square were used to incorporate siRNA, ribozyme, and fluorogenic RNA motifs. Unique intramolecular contact using the pre-existing intricacy of the 3WJ avoids relatively weaker intermolecular interactions via kissing loops or sticky ends. Utilizing the 3WJ motif, we have employed a modular design technique to construct variable-size RNA squares with controllable properties and functionalities for diverse and versatile applications with engineering, pharmaceutical, and medical potential. This technique for simple design to finely tune physicochemical properties adds a new angle to RNA nanotechnology. PMID:24971772

Development of low friction snake-inspired deterministic textured surfaces

NASA Astrophysics Data System (ADS)

Cuervo, P.; López, D. A.; Cano, J. P.; Sánchez, J. C.; Rudas, S.; Estupiñán, H.; Toro, A.; Abdel-Aal, H. A.

2016-06-01

The use of surface texturization to reduce friction in sliding interfaces has proved successful in some tribological applications. However, it is still difficult to achieve robust surface texturing with controlled designer-functionalities. This is because the current existing gap between enabling texturization technologies and surface design paradigms. Surface engineering, however, is advanced in natural surface constructs especially within legless reptiles. Many intriguing features facilitate the tribology of such animals so that it is feasible to discover the essence of their surface construction. In this work, we report on the tribological behavior of a novel class of surfaces of which the spatial dimensions of the textural patterns originate from micro-scale features present within the ventral scales of pre-selected snake species. Mask lithography was used to produce implement elliptical texturizing patterns on the surface of titanium alloy (Ti6Al4V) pins. To study the tribological behavior of the texturized pins, pin-on-disc tests were carried out with the pins sliding against ultra-high molecular weight polyethylene discs with no lubrication. For comparison, two non-texturized samples were also tested under the same conditions. The results show the feasibility of the texturization technique based on the coefficient of friction of the textured surfaces to be consistently lower than that of the non-texturized samples.

Plenoptic Imager for Automated Surface Navigation

NASA Technical Reports Server (NTRS)

Zollar, Byron; Milder, Andrew; Milder, Andrew; Mayo, Michael

2010-01-01

An electro-optical imaging device is capable of autonomously determining the range to objects in a scene without the use of active emitters or multiple apertures. The novel, automated, low-power imaging system is based on a plenoptic camera design that was constructed as a breadboard system. Nanohmics proved feasibility of the concept by designing an optical system for a prototype plenoptic camera, developing simulated plenoptic images and range-calculation algorithms, constructing a breadboard prototype plenoptic camera, and processing images (including range calculations) from the prototype system. The breadboard demonstration included an optical subsystem comprised of a main aperture lens, a mechanical structure that holds an array of micro lenses at the focal distance from the main lens, and a structure that mates a CMOS imaging sensor the correct distance from the micro lenses. The demonstrator also featured embedded electronics for camera readout, and a post-processor executing image-processing algorithms to provide ranging information.

Commercialisation of Solid Oxide Fuel Cells - opportunities and forecasts

NASA Astrophysics Data System (ADS)

Dziurdzia, B.; Magonski, Z.; Jankowski, H.

2016-01-01

The paper presents the analysis of commercialisation possibilities of the SOFC stack designed at AGH. The paper reminds the final design of the stack, presented earlier at IMAPS- Poland conferences, its recent modifications and measurements. The stack consists of planar double-sided ceramic fuel cells which characterize by the special anode construction with embedded fuel channels. The stack features by a simple construction without metallic interconnectors and frames, lowered thermal capacity and quick start-up time. Predictions for the possible applications of the stack include portable generators for luxurious caravans, yachts, ships at berth. The SOFC stack operating as clean, quiet and efficient power source could replace on-board diesel generators. Market forecasts shows that there is also some room on a market for the SOFC stack as a standalone generator in rural areas far away from the grid. The paper presents also the survey of SOFC market in Europe USA, Australia and other countries.

Quantum-enhanced deliberation of learning agents using trapped ions

NASA Astrophysics Data System (ADS)

Dunjko, V.; Friis, N.; Briegel, H. J.

2015-02-01

A scheme that successfully employs quantum mechanics in the design of autonomous learning agents has recently been reported in the context of the projective simulation (PS) model for artificial intelligence. In that approach, the key feature of a PS agent, a specific type of memory which is explored via random walks, was shown to be amenable to quantization, allowing for a speed-up. In this work we propose an implementation of such classical and quantum agents in systems of trapped ions. We employ a generic construction by which the classical agents are ‘upgraded’ to their quantum counterparts by a nested process of adding coherent control, and we outline how this construction can be realized in ion traps. Our results provide a flexible modular architecture for the design of PS agents. Furthermore, we present numerical simulations of simple PS agents which analyze the robustness of our proposal under certain noise models.

Experience in design and construction of the Log tunnel

NASA Astrophysics Data System (ADS)

Jovičić, Vojkan; Goleš, Niko; Tori, Matija; Peternel, Miha; Vajović, Stanojle; Muhić, Elvir

2017-09-01

A twin highway Log tunnel is a part of a new motorway connection between Maribor and Zagreb, section Draženci-Gru\\vskovje, which is located towards the border crossing between Slovenia and Croatia. The tunnel is currently under construction, and only the excavation works have been completed during the writing of this paper. The terrain in the area of the Log tunnel is diverse, and the route of the highway in its vicinity is characterised by deep excavations, bridges or viaducts. The Log tunnel is approximately 250 m long, partly constructed as a gallery. The geological conditions are dominated by Miocene base rock, featuring layers of well-connected clastic rocks, which are covered by diluvium clays, silts, sands and gravels of different thicknesses. Due to the short length of the tunnel, the usual separation of the motorway route to the left and the right tunnel axes was not carried out. Thus, the tunnel was constructed with an intermediate pillar and was designed as a three-lane tunnel, including the stopping lane. The construction of the tunnel was carried out using the New Austrian tunnelling method (NATM), in which the central adit was excavated first and the intermediate pillar was constructed within it. The excavation of the main tubes followed and was divided into the top heading, bench and the invert, enabling the intermediate pillar to take the load off the top heading of both tubes. The secondary lining of the tunnel is currently under construction. The experience of the tunnel construction gathered so far is presented in the paper. The main emphasis is on the construction of the intermediate pillar, which had to take the significant and asymmetrical ground load.

NOTE: An innovative phantom for quantitative and qualitative investigation of advanced x-ray imaging technologies

NASA Astrophysics Data System (ADS)

Chiarot, C. B.; Siewerdsen, J. H.; Haycocks, T.; Moseley, D. J.; Jaffray, D. A.

2005-11-01

Development, characterization, and quality assurance of advanced x-ray imaging technologies require phantoms that are quantitative and well suited to such modalities. This note reports on the design, construction, and use of an innovative phantom developed for advanced imaging technologies (e.g., multi-detector CT and the numerous applications of flat-panel detectors in dual-energy imaging, tomosynthesis, and cone-beam CT) in diagnostic and image-guided procedures. The design addresses shortcomings of existing phantoms by incorporating criteria satisfied by no other single phantom: (1) inserts are fully 3D—spherically symmetric rather than cylindrical; (2) modules are quantitative, presenting objects of known size and contrast for quality assurance and image quality investigation; (3) features are incorporated in ideal and semi-realistic (anthropomorphic) contexts; and (4) the phantom allows devices to be inserted and manipulated in an accessible module (right lung). The phantom consists of five primary modules: (1) head, featuring contrast-detail spheres approximate to brain lesions; (2) left lung, featuring contrast-detail spheres approximate to lung modules; (3) right lung, an accessible hull in which devices may be placed and manipulated; (4) liver, featuring conrast-detail spheres approximate to metastases; and (5) abdomen/pelvis, featuring simulated kidneys, colon, rectum, bladder, and prostate. The phantom represents a two-fold evolution in design philosophy—from 2D (cylindrically symmetric) to fully 3D, and from exclusively qualitative or quantitative to a design accommodating quantitative study within an anatomical context. It has proven a valuable tool in investigations throughout our institution, including low-dose CT, dual-energy radiography, and cone-beam CT for image-guided radiation therapy and surgery.

Model-Based Learning of Local Image Features for Unsupervised Texture Segmentation

NASA Astrophysics Data System (ADS)

Kiechle, Martin; Storath, Martin; Weinmann, Andreas; Kleinsteuber, Martin

2018-04-01

Features that capture well the textural patterns of a certain class of images are crucial for the performance of texture segmentation methods. The manual selection of features or designing new ones can be a tedious task. Therefore, it is desirable to automatically adapt the features to a certain image or class of images. Typically, this requires a large set of training images with similar textures and ground truth segmentation. In this work, we propose a framework to learn features for texture segmentation when no such training data is available. The cost function for our learning process is constructed to match a commonly used segmentation model, the piecewise constant Mumford-Shah model. This means that the features are learned such that they provide an approximately piecewise constant feature image with a small jump set. Based on this idea, we develop a two-stage algorithm which first learns suitable convolutional features and then performs a segmentation. We note that the features can be learned from a small set of images, from a single image, or even from image patches. The proposed method achieves a competitive rank in the Prague texture segmentation benchmark, and it is effective for segmenting histological images.

Advanced Extended Plate and Beam Wall System in a Cold-Climate House

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, Dave; Wiehagen, Joseph; Kochkin, Vladimir

This report presents the design and evaluation of an innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders. The EP&B design combines optimized framing with integrated rigid foam sheathing to increase the wallmore » system's R-value and reduce thermal bridging. The foam sheathing is installed between the wall studs and structural wood sheathing. The exterior wood sheathing is attached directly to a framing extension formed by extended top and bottom plates. The exterior wood sheathing can dry to the exterior and provides bracing, a clear drainage plane and flashing surface for window and door openings, and a nailing surface for siding attachment. With support of the DOE Building America program, Home Innovation Research Labs partnered with Lancaster County Career and Technology Center (LCCTC) to build a NCTH in Lancaster, PA to demonstrate the EP&B wall design in a cold climate (IECC climate zone 5A). The results of the study confirmed the benefits of the systems and the viability of its integration into the house construction process.« less

KSC-2009-6799

NASA Image and Video Library

2009-12-11

CAPE CANAVERAL, Fla. - Construction of the walls for the Propellants North Administrative and Maintenance Facility begins in Launch Complex 39 at NASA's Kennedy Space Center in Florida. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

KSC-2010-1117

NASA Image and Video Library

2010-01-07

CAPE CANAVERAL, Fla. - In Launch Complex 39 at NASA's Kennedy Space Center in Florida, a team of construction workers ensures that the walls of the Propellants North Administrative and Maintenance Facility are installed properly. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

KSC-2010-1119

NASA Image and Video Library

2010-01-07

CAPE CANAVERAL, Fla. - In Launch Complex 39 at NASA's Kennedy Space Center in Florida, steady progress is made by a team of construction workers to erect the walls of the Propellants North Administrative and Maintenance Facility. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

Energy conservation through optimum utilization of site energy sources for all season thermal comfort in new residential construction for single family attached (rowhouse/townhouse) designs

NASA Astrophysics Data System (ADS)

Gerber, S.; Holsman, J. P.

1981-02-01

A proposed design analysis is presented of a passive solar energy efficient system for a typical three level, three bedroom, two story, garage under townhouse. The design incorporates the best, most performance proven and cost effective products, materials, processes, technologies, and subsystems which are available today. Seven distinct categories recognized for analysis are identified as: the exterior environment; the interior environment; conservation of energy; natural energy utilization; auxiliary energy utilization; control and distribution systems; and occupant adaptation. Preliminary design features, fenestration systems, the plenum supply system, the thermal storage party fire walls, direct gain storage, the radiant comfort system, and direct passive cooling systems are briefly described.

Modular Design in Treaty Verification Equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macarthur, Duncan Whittemore; Benz, Jacob; Tolk, Keith

2015-01-27

It is widely believed that modular design is a good thing. However, there are often few explicit arguments, or even an agreed range of definitions, to back up this belief. In this paper, we examine the potential range of design modularity, the implications of various amounts of modularity, and the advantages and disadvantages of each level of modular construction. We conclude with a comparison of the advantages and disadvantages of each type, as well as discuss many caveats that should be observed to take advantage of the positive features of modularity and minimize the effects of the negative. The tradeoffsmore » described in this paper will be evaluated during the conceptual design to determine what amount of modularity should be included.« less

Effects of Swept Tips on V-22 Whirl Flutter and Loads

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.

2005-01-01

A CAMRAD II model of the V-22 Osprey tiltrotor was constructed for the purpose of analyzing the effects of blade design changes on whirl flutter. The model incorporated a dual load-path grip/yoke assembly, a swashplate coupled to the transmission case, and a drive train. A multiple-trailer free wake was used for loads calculations. The effects of rotor design changes on whirl-mode stability were calculated for swept blades and offset tip masses. A rotor with swept tips and inboard tuning masses was examined in detail to reveal the mechanisms by which these design changes affect stability and loads. Certain combinations of design features greatly increased whirl-mode stability, with (at worst) moderate increases to loads.

Wind energy development: methods for assessing risks to birds and bats pre-construction

USGS Publications Warehouse

Katzner, Todd E.; Bennett, Victoria; Miller, Tricia A.; Duerr, Adam E.; Braham, Melissa A.; Hale, Amanda

2016-01-01

Wind power generation is rapidly expanding. Although wind power is a low-carbon source of energy, it can impact negatively birds and bats, either directly through fatality or indirectly by displacement or habitat loss. Pre-construction risk assessment at wind facilities within the United States is usually required only on public lands. When conducted, it generally involves a 3-tier process, with each step leading to more detailed and rigorous surveys. Preliminary site assessment (U.S. Fish and Wildlife Service, Tier 1) is usually conducted remotely and involves evaluation of existing databases and published materials. If potentially at-risk wildlife are present and the developer wishes to continue the development process, then on-site surveys are conducted (Tier 2) to verify the presence of those species and to assess site-specific features (e.g., topography, land cover) that may influence risk from turbines. The next step in the process (Tier 3) involves quantitative or scientific studies to assess the potential risk of the proposed project to wildlife. Typical Tier-3 research may involve acoustic, aural, observational, radar, capture, tracking, or modeling studies, all designed to understand details of risk to specific species or groups of species at the given site. Our review highlights several features lacking from many risk assessments, particularly the paucity of before-and-after-control- impact (BACI) studies involving modeling and a lack of understanding of cumulative effects of wind facilities on wildlife. Both are essential to understand effective designs for pre-construction monitoring and both would help expand risk assessment beyond eagles.

Selection of adequate site location during early stages of construction project management: A multi-criteria decision analysis approach

NASA Astrophysics Data System (ADS)

Marović, Ivan; Hanak, Tomaš

2017-10-01

In the management of construction projects special attention should be given to the planning as the most important phase of decision-making process. Quality decision-making based on adequate and comprehensive collaboration of all involved stakeholders is crucial in project’s early stages. Fundamental reasons for existence of this problem arise from: specific conditions of construction industry (final products are inseparable from the location i.e. location has a strong influence of building design and its structural characteristics as well as technology which will be used during construction), investors’ desires and attitudes, and influence of socioeconomic and environment aspects. Considering all mentioned reasons one can conclude that selection of adequate construction site location for future investment is complex, low structured and multi-criteria problem. To take into account all the dimensions, the proposed model for selection of adequate site location is devised. The model is based on AHP (for designing the decision-making hierarchy) and PROMETHEE (for pairwise comparison of investment locations) methods. As a result of mixing basis feature of both methods, operational synergies can be achieved in multi-criteria decision analysis. Such gives the decision-maker a sense of assurance, knowing that if the procedure proposed by the presented model has been followed, it will lead to a rational decision, carefully and systematically thought out.

Low and high speed propellers for general aviation - Performance potential and recent wind tunnel test results

NASA Technical Reports Server (NTRS)

Jeracki, R. J.; Mitchell, G. A.

1981-01-01

A survey is presented of current research efforts in general aviation, low-speed propeller design and high-speed propfan design, with attention on such features as (1) advanced blade shapes, with novel airfoils and sweep, (2) tip devices, (3) integrated propeller/nacelle designs, (4) area-ruled spinners, (5) lightweight, all-composite blade construction, and (6) contra-rotating propfan systems. The potential overall improvements associated with these design modifications are calculated to lie at 10-15% for low-speed rotors and 15-30% for high-speed ones. Emphasis is placed on noise reduction, blade drag, performance prediction methods and wind tunnel testing of alternative rotor configurations. Extensive use of graphs is made in performance comparisons between alternative blade and rotor designs.

Fast and robust generation of feature maps for region-based visual attention.

PubMed

Aziz, Muhammad Zaheer; Mertsching, Bärbel

2008-05-01

Visual attention is one of the important phenomena in biological vision which can be followed to achieve more efficiency, intelligence, and robustness in artificial vision systems. This paper investigates a region-based approach that performs pixel clustering prior to the processes of attention in contrast to late clustering as done by contemporary methods. The foundation steps of feature map construction for the region-based attention model are proposed here. The color contrast map is generated based upon the extended findings from the color theory, the symmetry map is constructed using a novel scanning-based method, and a new algorithm is proposed to compute a size contrast map as a formal feature channel. Eccentricity and orientation are computed using the moments of obtained regions and then saliency is evaluated using the rarity criteria. The efficient design of the proposed algorithms allows incorporating five feature channels while maintaining a processing rate of multiple frames per second. Another salient advantage over the existing techniques is the reusability of the salient regions in the high-level machine vision procedures due to preservation of their shapes and precise locations. The results indicate that the proposed model has the potential to efficiently integrate the phenomenon of attention into the main stream of machine vision and systems with restricted computing resources such as mobile robots can benefit from its advantages.

KSC-2009-6797

NASA Image and Video Library

2009-12-11

CAPE CANAVERAL, Fla. - Construction of the Propellants North Administrative and Maintenance Facility begins in Launch Complex 39 at NASA's Kennedy Space Center in Florida. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

ELECTROMAGNETIC RELEASE MECHANISM

DOEpatents

Michelson, C.

1960-09-13

An electromagnetic release mechanism is offered that may be used, for example, for supporting a safety rod for a nuclear reactor. The release mechanism is designed to have a large excess holding force and a rapid, uniform, and dependable release. The fast release is accomplished by providing the electromagnet with slotttd polts separated by an insulating potting resin, and by constructing the poles with a ferro-nickel alloy. The combination of these two features materially reduces the eddy current power density whenever the magnetic field changes during a release operation. In addition to these features, the design of the armature is such as to provide ready entrance of fluid into any void that might tend to form during release of the armature. This also improves the release time for the mechanism. The large holding force for the mechanism is accomplished by providing a small, selected, uniform air gap between the inner pole piece and the armature.

A novel method for intelligent fault diagnosis of rolling bearings using ensemble deep auto-encoders

NASA Astrophysics Data System (ADS)

Shao, Haidong; Jiang, Hongkai; Lin, Ying; Li, Xingqiu

2018-03-01

Automatic and accurate identification of rolling bearings fault categories, especially for the fault severities and fault orientations, is still a major challenge in rotating machinery fault diagnosis. In this paper, a novel method called ensemble deep auto-encoders (EDAEs) is proposed for intelligent fault diagnosis of rolling bearings. Firstly, different activation functions are employed as the hidden functions to design a series of auto-encoders (AEs) with different characteristics. Secondly, EDAEs are constructed with various auto-encoders for unsupervised feature learning from the measured vibration signals. Finally, a combination strategy is designed to ensure accurate and stable diagnosis results. The proposed method is applied to analyze the experimental bearing vibration signals. The results confirm that the proposed method can get rid of the dependence on manual feature extraction and overcome the limitations of individual deep learning models, which is more effective than the existing intelligent diagnosis methods.

a Conceptual Model for the Representation of Landforms Using Ontology Design Patterns

NASA Astrophysics Data System (ADS)

Guilbert, Eric; Moulin, Bernard; Cortés Murcia, Andrés

2016-06-01

A landform is an area of a terrain with its own recognisable shape. Its definition is often qualitative and inherently vague. Hence landforms are difficult to formalise in view of their extraction from a DTM. This paper presents a two-level framework for the representation of landforms. The objective is to provide a structure where landforms can be conceptually designed according to a common model which can be implemented. It follows the principle that landforms are not defined by geometrical characteristics but by salient features perceived by people. Hence, these salient features define a skeleton around which the landform is built. The first level of our model defines general concepts forming a landform prototype while the second level provides a model for the translation of these concepts and landform extraction on a DTM. The model is still under construction and preliminary results together with current developments are also presented.

Cell module and fuel conditioner development

NASA Technical Reports Server (NTRS)

Hoover, D. Q., Jr.

1981-01-01

The design features and plans for fabrication of Stacks 564 and 800 are described. The results of the OS/IES loop testing of Stack 562, endurance testing of Stack 560 and the post test analysis of Stack 561 are reported. Progress on construction and modification of the fuel cell test facilities and the 10 kW reformer test station is described. Efforts to develop the technical data base for the fuel conditioning system included vendor contacts, packed bed heat transfer tests, development of the BOLTAR computer program, and work on the detailed design of the 10 kW reformer are described.

A corner-reflector mixer mount for far infrared wavelengths.

PubMed

Zmuidzinas, J; Betz, A L; Boreiko, R T

1989-01-01

A new type of corner-reflector mixer mount, which has the advantages of ease of fabrication and assembly as well as frequency versatility, has been designed and constructed. The mixer works with arbitrary antenna lengths > or = 4 lambda with the reflector to antenna spacing adjusted to give a strong and symmetric central lobe. The predicted response patterns have been experimentally verified for various antenna lengths and operating frequencies between 800 and 2000 GHz. An important design feature is the incorporation of a microstrip matching network which eliminates IF impedance mismatch and provides mechanical isolation of the whisker antenna.

The use of hybrid integrated circuit techniques in biotelemetry applications

NASA Technical Reports Server (NTRS)

Fryer, T. B.

1977-01-01

A review is presented of some features of hybrid integrated circuits that make their use advantageous in miniature biotelemetry applications. The various techniques for fabricating resistors, capacitors and interconnections by both thin film and thick film technology are discussed. The use of chip capacitors, resistors, and especially standard IC chips on substrates with fired-on interconnection patterns is emphasized. The review is designed primarily to acquaint biotelemetry users and designers with an overview of this fabrication technique so that they can better communicate their needs with an understanding of its limitations and advantages to facilities specializing in hybrid construction.

On the design of a hierarchical SS7 network: A graph theoretical approach

NASA Astrophysics Data System (ADS)

Krauss, Lutz; Rufa, Gerhard

1994-04-01

This contribution is concerned with the design of Signaling System No. 7 networks based on graph theoretical methods. A hierarchical network topology is derived by combining the advantage of the hierarchical network structure with the realization of node disjoint routes between nodes of the network. By using specific features of this topology, we develop an algorithm to construct circle-free routing data and to assure bidirectionality also in case of failure situations. The methods described are based on the requirements that the network topology, as well as the routing data, may be easily changed.

Quadratic trigonometric B-spline for image interpolation using GA

PubMed Central

Abbas, Samreen; Irshad, Misbah

2017-01-01

In this article, a new quadratic trigonometric B-spline with control parameters is constructed to address the problems related to two dimensional digital image interpolation. The newly constructed spline is then used to design an image interpolation scheme together with one of the soft computing techniques named as Genetic Algorithm (GA). The idea of GA has been formed to optimize the control parameters in the description of newly constructed spline. The Feature SIMilarity (FSIM), Structure SIMilarity (SSIM) and Multi-Scale Structure SIMilarity (MS-SSIM) indices along with traditional Peak Signal-to-Noise Ratio (PSNR) are employed as image quality metrics to analyze and compare the outcomes of approach offered in this work, with three of the present digital image interpolation schemes. The upshots show that the proposed scheme is better choice to deal with the problems associated to image interpolation. PMID:28640906

Quadratic trigonometric B-spline for image interpolation using GA.

PubMed

Hussain, Malik Zawwar; Abbas, Samreen; Irshad, Misbah

2017-01-01

In this article, a new quadratic trigonometric B-spline with control parameters is constructed to address the problems related to two dimensional digital image interpolation. The newly constructed spline is then used to design an image interpolation scheme together with one of the soft computing techniques named as Genetic Algorithm (GA). The idea of GA has been formed to optimize the control parameters in the description of newly constructed spline. The Feature SIMilarity (FSIM), Structure SIMilarity (SSIM) and Multi-Scale Structure SIMilarity (MS-SSIM) indices along with traditional Peak Signal-to-Noise Ratio (PSNR) are employed as image quality metrics to analyze and compare the outcomes of approach offered in this work, with three of the present digital image interpolation schemes. The upshots show that the proposed scheme is better choice to deal with the problems associated to image interpolation.

Designing for auto safety

NASA Technical Reports Server (NTRS)

Driver, E. T.

1971-01-01

Safety design features in the motor vehicle and highway construction fields result from systems analysis approach to prevent or lessen death, injury, and property damage results. Systems analysis considers the prevention of crashes, increased survivability in crashes, and prompt medical attention to injuries as well as other postcrash salvage measures. The interface of these system elements with the driver, the vehicle, and the environment shows that action on the vehicle system produces the greatest safety payoff through design modifications. New and amended safety standards developed through hazard analysis technique improved accident statistics in the 70'; these regulations include driver qualifications and countermeasures to identify the chronic drunken driver who is involved in more than two-thirds of all auto deaths.

Design and development of a new SRF cavity cryomodule for the ATLAS intensity upgrade

NASA Astrophysics Data System (ADS)

Kedzie, Mark; Conway, Zachary; Fuerst, Joel; Gerbick, Scott; Kelly, Michael; Morgan, James; Ostroumov, Peter; O'Toole, Michael; Shepard, Kenneth

2012-06-01

The ATLAS heavy ion linac at Argonne National Laboratory is undergoing an intensity upgrade that includes the development and implementation of a new cryomodule containing four superconducting solenoids and seven quarter-wave drift-tube-loaded superconducting rf cavities. The rf cavities extend the state of the art for this class of structure and feature ASME code stamped stainless steel liquid helium containment vessels. The cryomodule design is a further evolution of techniques recently implemented in a previous upgrade [1]. We provide a status report on the construction effort and describe the vacuum vessel, thermal shield, cold mass support and alignment, and other subsystems including couplers and tuners. Cavity mechanical design is also reviewed.

Design, construction and performance of an experimental watershed to support a fen peatland for mine landscape reclamation

NASA Astrophysics Data System (ADS)

Price, J. S.; Petrone, R. M.; Strack, M.; Cooper, D. J.

2017-12-01

In the Alberta oil sands region, fen peatlands comprised 50% of the boreal landscape. Oil sands mining has stripped over 800 km2 of land surface to access bitumen, necessitating landscape reclamation to re-establish functional wetlands. Fens are peat-dominated wetlands that commonly rely on groundwater to supplement their water budget and deliver dissolved solutes that impart a distinct geochemistry, hence vegetation community. A numerical model was used to test the concept and guide selection of earth materials and system geometry. The goal was to maintain the placed peat in a sufficiently wet condition to support wetland plants and become a net carbon sink, in this sub-humid climate. The 32.1 ha Nikanotee Fen Watershed comprises a 7.7 ha upland, that was designed to recharge sufficient water, and deliver it to the 2.9 ha fen via groundwater flow. These features are surrounded by other reclaimed slopes designed to store water, rather than deliver it downslope. Four years of monitoring since construction show the fen maintains a high water table, and the peatland has become a strong carbon sink, even though the hydrological performance of construction materials varied substantially from what was anticipated (lower hydraulic conductivity). However, solutes associated with the tailings sand used in construction are moving towards the fen, and are expected to influence the future vegetation community and system biogeochemistry. One of the biggest uncertainties is the changing performance of soils and vegetation as they develop.

The Influences of Landscape Features on Visitation of Hospital Green Spaces-A Choice Experiment Approach.

PubMed

Chang, Kaowen Grace; Chien, Hungju

2017-07-05

Studies have suggested that visiting and viewing landscaping at hospitals accelerates patient's recovery from surgery and help staff's recovery from mental fatigue. To plan and construct such landscapes, we need to unravel landscape features desirable to different groups so that the space can benefit a wide range of hospital users. Using discrete choice modeling, we developed experimental choice sets to investigate how landscape features influence the visitations of different users in a large regional hospital in Taiwan. The empirical survey provides quantitative estimates of the influence of each landscape feature on four user groups, including patients, caregivers, staff, and neighborhood residents. Our findings suggest that different types of features promote visits from specific user groups. Landscape features facilitating physical activities effectively encourage visits across user groups especially for caregivers and staff. Patients in this study specify a strong need for contact with nature. The nearby community favors the features designed for children's play and family activities. People across user groups value the features that provide a mitigated microclimate of comfort, such as a shelter. Study implications and limitations are also discussed. Our study provides information essential for creating a better healing environment in a hospital setting.

A Two-Stream Deep Fusion Framework for High-Resolution Aerial Scene Classification

PubMed Central

Liu, Fuxian

2018-01-01

One of the challenging problems in understanding high-resolution remote sensing images is aerial scene classification. A well-designed feature representation method and classifier can improve classification accuracy. In this paper, we construct a new two-stream deep architecture for aerial scene classification. First, we use two pretrained convolutional neural networks (CNNs) as feature extractor to learn deep features from the original aerial image and the processed aerial image through saliency detection, respectively. Second, two feature fusion strategies are adopted to fuse the two different types of deep convolutional features extracted by the original RGB stream and the saliency stream. Finally, we use the extreme learning machine (ELM) classifier for final classification with the fused features. The effectiveness of the proposed architecture is tested on four challenging datasets: UC-Merced dataset with 21 scene categories, WHU-RS dataset with 19 scene categories, AID dataset with 30 scene categories, and NWPU-RESISC45 dataset with 45 challenging scene categories. The experimental results demonstrate that our architecture gets a significant classification accuracy improvement over all state-of-the-art references. PMID:29581722

A Two-Stream Deep Fusion Framework for High-Resolution Aerial Scene Classification.

PubMed

Yu, Yunlong; Liu, Fuxian

2018-01-01

One of the challenging problems in understanding high-resolution remote sensing images is aerial scene classification. A well-designed feature representation method and classifier can improve classification accuracy. In this paper, we construct a new two-stream deep architecture for aerial scene classification. First, we use two pretrained convolutional neural networks (CNNs) as feature extractor to learn deep features from the original aerial image and the processed aerial image through saliency detection, respectively. Second, two feature fusion strategies are adopted to fuse the two different types of deep convolutional features extracted by the original RGB stream and the saliency stream. Finally, we use the extreme learning machine (ELM) classifier for final classification with the fused features. The effectiveness of the proposed architecture is tested on four challenging datasets: UC-Merced dataset with 21 scene categories, WHU-RS dataset with 19 scene categories, AID dataset with 30 scene categories, and NWPU-RESISC45 dataset with 45 challenging scene categories. The experimental results demonstrate that our architecture gets a significant classification accuracy improvement over all state-of-the-art references.

Monolithic ceramic capacitors for high reliability applications

NASA Technical Reports Server (NTRS)

Thornley, E. B.

1981-01-01

Monolithic multi-layer ceramic dielectric capacitors are widely used in high reliability applications in spacecraft, launch vehicles, and military equipment. Their relatively low cost, wide range of values, and package styles are attractive features that result in high usage in electronic circuitry in these applications. Design and construction of monolithic ceramic dielectric capacitors, defects that can lead to failure, and methods for defect detection that are being incorporated in military specifications are discussed.

Resonant cryogenic chopper. [for infrared and submillimeter radiometers

NASA Technical Reports Server (NTRS)

Page, Lyman A.; Cheng, Edward S.; Meyer, Stephan S.

1992-01-01

An account is given of the design features, construction, and performance of a both mechanically and thermally robust, resonant cryogenic chopper operating at 4.2 K. The chopper can occult a 2.54-cm aperture at 4.5 Hz, with approximately 1-mW dissipation. The controllability of the stator and rotor magnetic fields facilitates performance optimization and the determination of any possible interference effects. Attention is given to long-term amplitude stability determinations.

Scalable Multiplexed Ion Trap (SMIT) Program

DTIC Science & Technology

2010-12-08

an integrated micromirror . The symmetric cross and the mirror trap had a number of complex design features. Both traps shaped the electrodes in...genetic algorithm. 6. Integrated micromirror . The Gen II linear trap (as well as the linear sections of the mirror and the cross) had a number of new...conventional imaging system constructed by off-the-shelf optical components and a micromirror located very close to the ion. A large fraction of photons

Solar 2 Green Energy, Arts & Education Center. Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paquette, Jamie C; Collins, Christopher J

The Solar 2 Green Energy, Arts and Education Center is an 8,000 sq.ft. demonstration project that will be constructed to Platinum LEED certification and will be the first carbon-neutral, net-zero energy use public building in New York City, giving it local and national appeal. Employing green building features and holistic engineering practices throughout its international award-winning design, Solar 2 will be powered by a 90kW photovoltaic (PV) array in conjunction with a geothermal heating and cooling system and a high efficient design that seeks to reduce the overall energy load of the building. Solar 2 will replace our current 500more » sq.ft. prototype facility - known as Solar 1 - as the educational and cultural centerpiece of a five-block public greenway on the East River in Stuyvesant Cove Park, located along two acres of public riverfront on a newly reclaimed, former brownfield in lower Manhattan. Designed as a public-use complex for year-round environmental education exhibits and onsite activities for all ages and backgrounds, Solar 2 will demonstrate energy-efficiency technologies and sustainable environmental practices available now to all urban residents, eco-tourists, teachers, and students alike. Showcasing one of Solar 2's most striking design elements is the PV roof array with a cafe and river vistas for miles of New York City's skylines. Capping the building as a solar-powered landmark, and visible from the FDR Drive, the PV array is also designed to provide visitors below a view of the solar roof when standing outside, as well as directly underneath it. Recognized by an international jury of architects, civil engineers and urban designers by the Swiss-based Holcim Foundation, the Solar 2 design was awarded the prestigious Holcim North American 2008 Gold Award for Sustainable Construction for innovative, future-oriented and tangible sustainable construction projects, selected from more than 1900 entries. Funding from the Department of Energy was provided to assist with the ongoing design work of Solar 2, including architecture, engineering and the development of construction specifications. The work performed during the project period brought this process as far along as it could go pending the raising of funds to begin construction of the building. Once those funds are secured, we will finalize any additional details needed before beginning the bidding process and then moving into construction. DOE's funding was extremely valuable in helping Solar One determine the feasibility of a net-zero construction on the site and allowed for the design to project to meet the high standards necessary for LEED Platinum status.« less

Generation of flat-top pulsed magnetic fields with feedback control approach.

PubMed

Kohama, Yoshimitsu; Kindo, Koichi

2015-10-01

We describe the construction of a simple, compact, and cost-effective feedback system that produces flat-top field profiles in pulsed magnetic fields. This system is designed for use in conjunction with a typical capacitor-bank driven pulsed magnet and was tested using a 60-T pulsed magnet. With the developed feedback controller, we have demonstrated flat-top magnetic fields as high as 60.64 T with an excellent field stability of ±0.005 T. The result indicates that the flat-top pulsed magnetic field produced features high field stability and an accessible field strength. These features make this system useful for improving the resolution of data with signal averaging.

Large area and low power dielectrowetting optical shutter with local deterministic fluid film breakup

NASA Astrophysics Data System (ADS)

Zhao, R.; Cumby, B.; Russell, A.; Heikenfeld, J.

2013-11-01

A large area (>10 cm2) and low-power (0.1-10 Hz AC voltage, ˜10's μW/cm2) dielectrowetting optical shutter requiring no pixelation is demonstrated. The device consists of 40 μm interdigitated electrodes covered by fluid splitting features and a hydrophobic fluoropolymer. When voltage is removed, the fluid splitting features initiate breakup of the fluid film into small droplets resulting in ˜80% transmission. Both the dielectrowetting and fluid splitting follow theory, allowing prediction of alternate designs and further improved performance. Advantages include scalability, optical polarization independence, high contrast ratio, fast response, and simple construction, which could be of use in switchable windows or transparent digital signage.

Graphene-Based Optical Biosensors and Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Zhiwen; He, Shijiang; Pei, Hao

2014-01-13

This chapter focuses on the design, fabrication and application of graphene based optical nanobiosensors. The emerging graphene based optical nanobiosensors demonstrated the promising bioassay and biomedical applications thanking to the unique optical features of graphene. According to the different applications, the graphene can be tailored to form either fluorescent emitter or efficient fluorescence quencher. The exceptional electronic feature of graphene makes it a powerful platform for fabricating the SPR and SERS biosensors. Today the graphene based optical biosensors have been constructed to detect various targets including ions, small biomolecules, DNA/RNA and proteins. This chapter reviews the recent progress in graphene-basedmore » optical biosensors and discusses the opportunities and challenges in this field.« less

Integrating Health Behavior Theory and Design Elements in Serious Games

PubMed Central

Fleming, Theresa; Lucassen, Mathijs FG; Bridgman, Heather; Stasiak, Karolina; Shepherd, Matthew; Orpin, Peter

2015-01-01

Background Internet interventions for improving health and well-being have the potential to reach many people and fill gaps in service provision. Serious gaming interfaces provide opportunities to optimize user adherence and impact. Health interventions based in theory and evidence and tailored to psychological constructs have been found to be more effective to promote behavior change. Defining the design elements which engage users and help them to meet their goals can contribute to better informed serious games. Objective To elucidate design elements important in SPARX, a serious game for adolescents with depression, from a user-centered perspective. Methods We proposed a model based on an established theory of health behavior change and practical features of serious game design to organize ideas and rationale. We analyzed data from 5 studies comprising a total of 22 focus groups and 66 semistructured interviews conducted with youth and families in New Zealand and Australia who had viewed or used SPARX. User perceptions of the game were applied to this framework. Results A coherent framework was established using the three constructs of self-determination theory (SDT), autonomy, competence, and relatedness, to organize user perceptions and design elements within four areas important in design: computer game, accessibility, working alliance, and learning in immersion. User perceptions mapped well to the framework, which may assist developers in understanding the context of user needs. By mapping these elements against the constructs of SDT, we were able to propose a sound theoretical base for the model. Conclusions This study’s method allowed for the articulation of design elements in a serious game from a user-centered perspective within a coherent overarching framework. The framework can be used to deliberately incorporate serious game design elements that support a user’s sense of autonomy, competence, and relatedness, key constructs which have been found to mediate motivation at all stages of the change process. The resulting model introduces promising avenues for future exploration. Involving users in program design remains an imperative if serious games are to be fit for purpose. PMID:26543916

Strategic advantages of high-rise construction

NASA Astrophysics Data System (ADS)

Yaskova, Natalya

2018-03-01

Traditional methods to assess the competitiveness of different types of real estate in the context of huge changes of new technological way of life don't provide building solutions that would be correct from a strategic perspective. There are many challenges due to changes in the consumers' behavior in the housing area. A multiplicity of life models, a variety of opportunities and priorities, traditions and new trends in construction should be assessed in terms of prospective benefits in the environment of the emerging new world order. At the same time, the mane discourse of high-rise construction mainly relates to its design features, technical innovations, and architectural accents. We need to clarify the criteria for economic evaluation of high-rise construction in order to provide decisions with clear and quantifiable contexts. The suggested approach to assessing the strategic advantage of high-rise construction and the prospects for capitalization of high-rise buildings poses new challenges for the economy to identify adequate quantitative assessment methods of the high-rise buildings economic efficiency, taking into account all stages of their life cycle.

Normative and economic foundations of high-rise construction in the city of Samara

NASA Astrophysics Data System (ADS)

Didkovskaya, Olga V.; Bocharov, Aleksey Y.; Ilyina, Marina V.; Mamaeva, Olga A.

2018-03-01

Every year the number of free land plots for construction of buildings is steadily decreasing in cities. In this regard, the participants in the investment and construction process are increasingly seeking to maximize the use of land. A logical way for this is to use high-rise construction. However, until recently, builders encountered serious obstacles in the form of lack of special norms and rules for the design of high-rise buildings. It led to the need for individual coordination of each high-rise facility, the development and approval of special technical conditions, the passage of numerous administrative approvals. Thus, investment activity regarding the construction of high-rise buildings in the Russian Federation is reduced. In 2016, there were regulatory changes that substantially alleviated these difficulties. In this article, the authors analyze the features of the town-planning normative-legal field of high-rise construction and its development, track the interrelations between the regulatory regulation of the construction of similar facilities, with the real need, the technical feasibility and economic feasibility of their construction in the urban district of Samara. Conclusions and suggestions are also based on the analysis of the norms of urban zoning, the residential real estate market and the value of land plots.

Emulating multiple inheritance in Fortran 2003/2008

DOE PAGES

Morris, Karla

2015-01-24

Although the high-performance computing (HPC) community increasingly embraces object-oriented programming (OOP), most HPC OOP projects employ the C++ programming language. Until recently, Fortran programmers interested in mining the benefits of OOP had to emulate OOP in Fortran 90/95. The advent of widespread compiler support for Fortran 2003 now facilitates explicitly constructing object-oriented class hierarchies via inheritance and leveraging related class behaviors such as dynamic polymorphism. Although C++ allows a class to inherit from multiple parent classes, Fortran and several other OOP languages restrict or prohibit explicit multiple inheritance relationships in order to circumvent several pitfalls associated with them. Nonetheless, whatmore » appears as an intrinsic feature in one language can be modeled as a user-constructed design pattern in another language. The present paper demonstrates how to apply the facade structural design pattern to support a multiple inheritance class relationship in Fortran 2003. As a result, the design unleashes the power of the associated class relationships for modeling complicated data structures yet avoids the ambiguities that plague some multiple inheritance scenarios.« less

Development of patient-centric linguistically tailored psychoeducational messages to support nutrition and medication self-management in type 2 diabetes: a feasibility study

PubMed Central

Ellis, Rebecca J Bartlett; Connor, Ulla; Marshall, James

2014-01-01

Purpose This study evaluated the feasibility of developing linguistically tailored educational messages designed to match the linguistic styles of patients segmented into types with the Descriptor™, and to determine patient preferences for tailored or standard messages based on their segments. Patients and methods Twenty patients with type 2 diabetes (T2DM) were recruited from a diabetes health clinic. Participants were segmented using the Descriptor™, a language-based questionnaire, to identify patient types based on their control orientation (internal/external), agency (high/low), and affect (positive/negative), which are well studied constructs related to T2DM self-management. Two of the seven self-care behaviors described by the American Association of Diabetes Educators (healthy eating and taking medication) were used to develop standard messages and then linguistically tailored using features of the six different construct segment types of the Descriptor™. A subset of seven participants each provided feedback on their preference for standard or linguistically tailored messages; 12 comparisons between standard and tailored messages were made. Results Overall, the tailored messages were preferred to the standard messages. When the messages were matched to specific construct segment types, the tailored messages were preferred over the standard messages, although this was not statistically significant. Conclusion Linguistically tailoring messages based on construct segments is feasible. Furthermore, tailored messages were more often preferred over standard messages. This study provides some preliminary evidence for tailoring messages based on the linguistic features of control orientation, agency, and affect. The messages developed in this study should be tested in a larger more representative sample. The present study did not explore whether tailored messages were better understood. This research will serve as preliminary evidence to develop future studies with the ultimate goal to design intervention studies to investigate if linguistically tailoring communication within the context of patient education influences patient knowledge, motivation, and activation toward making healthy behavior changes in T2DM self-management. PMID:25336928

Identification of input variables for feature based artificial neural networks-saccade detection in EOG recordings.

PubMed

Tigges, P; Kathmann, N; Engel, R R

1997-07-01

Though artificial neural networks (ANN) are excellent tools for pattern recognition problems when signal to noise ratio is low, the identification of decision relevant features for ANN input data is still a crucial issue. The experience of the ANN designer and the existing knowledge and understanding of the problem seem to be the only links for a specific construction. In the present study a backpropagation ANN based on modified raw data inputs showed encouraging results. Investigating the specific influences of prototypical input patterns on a specially designed ANN led to a new sparse and efficient input data presentation. This data coding obtained by a semiautomatic procedure combining existing expert knowledge and the internal representation structures of the raw data based ANN yielded a list of feature vectors, each representing the relevant information for saccade identification. The feature based ANN produced a reduction of the error rate of nearly 40% compared with the raw data ANN. An overall correct classification of 92% of so far unknown data was realized. The proposed method of extracting internal ANN knowledge for the production of a better input data representation is not restricted to EOG recordings, and could be used in various fields of signal analysis.

Examining the Impact of Question Surface Features on Students' Answers to Constructed-Response Questions on Photosynthesis

ERIC Educational Resources Information Center

Weston, Michele; Haudek, Kevin C.; Prevost, Luanna; Urban-Lurain, Mark; Merrill, John

2015-01-01

One challenge in science education assessment is that students often focus on surface features of questions rather than the underlying scientific principles. We investigated how student written responses to constructed-response questions about photosynthesis vary based on two surface features of the question: the species of plant and the order of…

Green Construction in Building Renovation

NASA Astrophysics Data System (ADS)

Ksit, Barbara; Majcherek, Michał

2016-06-01

Modern materials and construction solutions draw more and more attention to ecology and building certification. Among the criteria appearing in revitalization, an important element is bringing plants back into heavily urbanized areas. In its natural form, this is not possible to carry out everywhere, often requiring large amounts of space. Nowadays, however, there are a number of green roofs and green wall systems, allowing "greener" construction without making significant changes in the urban environment. The article includes a presentation and analysis of selected solutions of biological surfaces known as green roofs and green walls, specifying various solutions and their most important features. The case study focuses primarily on material and design solutions, as well as the potential benefits, risks and limitations in their use. Plants structures on the surfaces of vertical and horizontal partitions continue to be a very interesting alternative to take into account when applying for grants, such as LEED or BREEAM certificates.

The Fluid Mechanics of a Wavy-Wall Bioreactor

NASA Astrophysics Data System (ADS)

Sucosky, Philippe; Bilgen, Bahar; Aleem, Alexander; Neitzel, Paul; Barabino, Gilda

2004-11-01

Bioreactors are devices used for the production of mammalian tissue in vitro. Although mixing has been shown to stimulate the growth of cartilage constructs, high shear-stress levels can damage the cells. In order to enhance mixing while minimizing shear, a wavy-wall bioreactor (WWB) featuring a sinusoidal internal profile has been designed. The turbulent hydrodynamic environment produced in this device is investigated experimentally using particle-image velocimetry. A model bioreactor made of acrylic and filled with an index-matching solution of zinc iodide is used to compensate for the refraction of light at the walls. The flow observed in different planes is shown to be periodic, spatially dependent, and dominated by mean-shear rather than Reynolds stresses in the vicinity of constructs. Finally, a comparison between the mean-shear stresses obtained in the WWB and in a standard spinner flask reveals similar stress levels near the construct walls.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mehrez, Loujaine; Ghanem, Roger; Aitharaju, Venkat

Design of non-crimp fabric (NCF) composites entails major challenges pertaining to (1) the complex fine-scale morphology of the constituents, (2) the manufacturing-produced inconsistency of this morphology spatially, and thus (3) the ability to build reliable, robust, and efficient computational surrogate models to account for this complex nature. Traditional approaches to construct computational surrogate models have been to average over the fluctuations of the material properties at different scale lengths. This fails to account for the fine-scale features and fluctuations in morphology, material properties of the constituents, as well as fine-scale phenomena such as damage and cracks. In addition, it failsmore » to accurately predict the scatter in macroscopic properties, which is vital to the design process and behavior prediction. In this work, funded in part by the Department of Energy, we present an approach for addressing these challenges by relying on polynomial chaos representations of both input parameters and material properties at different scales. Moreover, we emphasize the efficiency and robustness of integrating the polynomial chaos expansion with multiscale tools to perform multiscale assimilation, characterization, propagation, and prediction, all of which are necessary to construct the data-driven surrogate models required to design under the uncertainty of composites. These data-driven constructions provide an accurate map from parameters (and their uncertainties) at all scales and the system-level behavior relevant for design. While this perspective is quite general and applicable to all multiscale systems, NCF composites present a particular hierarchy of scales that permits the efficient implementation of these concepts.« less

CasCADe: A Novel 4D Visualization System for Virtual Construction Planning.

PubMed

Ivson, Paulo; Nascimento, Daniel; Celes, Waldemar; Barbosa, Simone Dj

2018-01-01

Building Information Modeling (BIM) provides an integrated 3D environment to manage large-scale engineering projects. The Architecture, Engineering and Construction (AEC) industry explores 4D visualizations over these datasets for virtual construction planning. However, existing solutions lack adequate visual mechanisms to inspect the underlying schedule and make inconsistencies readily apparent. The goal of this paper is to apply best practices of information visualization to improve 4D analysis of construction plans. We first present a review of previous work that identifies common use cases and limitations. We then consulted with AEC professionals to specify the main design requirements for such applications. These guided the development of CasCADe, a novel 4D visualization system where task sequencing and spatio-temporal simultaneity are immediately apparent. This unique framework enables the combination of diverse analytical features to create an information-rich analysis environment. We also describe how engineering collaborators used CasCADe to review the real-world construction plans of an Oil & Gas process plant. The system made evident schedule uncertainties, identified work-space conflicts and helped analyze other constructability issues. The results and contributions of this paper suggest new avenues for future research in information visualization for the AEC industry.

Long-Term Drainage from the Riprap Side Slope of a Surface Barrier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhuanfang

Surface barriers designed to isolate underground nuclear waste in place are expected to function for at least 1000 years. To achieve this long design life, such barriers need to be protected with side slopes against wind- and water-induced erosion and damage by natural or human activities. However, the side slopes are usually constructed with materials coarser than the barrier. Their hydrological characteristics must be understood so that any drainage from them is considered in the barrier design and will not compromise the barrier function. The Prototype Hanford Barrier, an evapotranspiration-capillary (ETC) barrier, was constructed in 1994 at the Hanford Sitemore » in southeastern Washington state, with a gravel side slope and a riprap side slope. The soil water content in the gravel side slope and drainage from both side slopes have been monitored since the completion of construction. The monitoring results show that under natural precipitation the annual drainage rates from the two types of side slopes were very similar and about 5 times the typical recharge from local soil with natural vegetation and 40 times the barrier design criterion. The higher recharge from the side slopes results in some of the drainage migrating laterally to the region beneath the ETC barrier. This edge effect of the enhanced drainage was evaluated for a period of 1000 years by numerical simulation. The edge effect was quantified by the amount of water across the barrier edges and the affecting distance of the barrier edges. These results indicate that design features can be adjusted to reduce the edge effect when necessary.« less

Building America Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House, Mount Joy, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

This report presents the design and evaluation of a innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders. The EP&B design combines optimized framing with integrated rigid foam sheathing to increase the wallmore » system's R-value and reduce thermal bridging. The foam sheathing is installed between the wall studs and structural wood sheathing. The exterior wood sheathing is attached directly to a framing extension formed by extended top and bottom plates. The exterior wood sheathing can dry to the exterior and provides bracing, a clear drainage plane and flashing surface for window and door openings, and a nailing surface for siding attachment. With support of the DOE Building America program, Home Innovation Research Labs partnered with Lancaster County Career and Technology Center (LCCTC) to build a NCTH in Lancaster, PA to demonstrate the EP&B wall design in a cold climate (IECC climate zone 5A). The results of the study confirmed the benefits of the systems and the viability of its integration into the house construction process.« less

The development and testing of the thermal break divertor monoblock target design delivering 20 MW m-2 heat load capability

NASA Astrophysics Data System (ADS)

Fursdon, M.; Barrett, T.; Domptail, F.; Evans, Ll M.; Luzginova, N.; Greuner, N. H.; You, J.-H.; Li, M.; Richou, M.; Gallay, F.; Visca, E.

2017-12-01

The design and development of a novel plasma facing component (for fusion power plants) is described. The component uses the existing ‘monoblock’ construction which consists of a tungsten ‘block’ joined via a copper interlayer to a through CuCrZr cooling pipe. In the new concept the interlayer stiffness and conductivity properties are tuned so that stress in the principal structural element of the component (the cooling pipe) is reduced. Following initial trials with off-the-shelf materials, the concept was realized by machined features in an otherwise solid copper interlayer. The shape and distribution of the features were tuned by finite element analyses subject to ITER structural design criterion in-vessel components (SDC-IC) design rules. Proof of concept mock-ups were manufactured using a two stage brazing process verified by tomography and micrographic inspection. Full assemblies were inspected using ultrasound and thermographic (SATIR) test methods at ENEA and CEA respectively. High heat flux tests using IPP’s GLADIS facility showed that 200 cycles at 20 MW m-2 and five cycles at 25 MW m-2 could be sustained without apparent component damage. Further testing and component development is planned.

Patients and their families weigh in on evidence-based hospital design.

PubMed

Trochelman, Kathleen; Albert, Nancy; Spence, Jacqueline; Murray, Terri; Slifcak, Ellen

2012-02-01

In 2 landmark publications, the Institute of Medicine reported on significant deficiencies in our current health care system. In response, an area of research examining the role of the physical environment in influencing outcomes for patients and staff gained momentum. The concept of evidence-based design has evolved, and the development of structural guidelines for new hospital construction was instituted by the American Institute of Architects in 2006. To determine perceptions of patients and their families of evidence-based design features in a new heart center. Hospitalized patients and their families, most of whom were in intensive care and step-down units, were surveyed and data from the Hospital Consumer Assessment of Healthcare Providers and Systems were reviewed to determine perceptions of evidence-based design features incorporated into a new heart center and to assess patients' satisfaction with the environment. Results Responses were reviewed and categorized descriptively. Five general environment topics of focus emerged: privacy, space, noise, light, and overall atmosphere. Characteristics perceived as being dissatisfying and satisfying are discussed. Critical care nurses must be aware of the current need to recognize how much the physical environment influences care delivery and take steps to maximize patients' safety, satisfaction, and quality of care.

Sustainable urban stormwater management in the tropics: An evaluation of Singapore's ABC Waters Program

NASA Astrophysics Data System (ADS)

Lim, H. S.; Lu, X. X.

2016-07-01

The Active Beautiful Clean (ABC) Waters Program was implemented in 2006 as part of Singapore's stormwater management strategy and reflects the country's move towards Water Sensitive Urbanism through the adoption of Low-Impact Development (LID) ideology and practices. It is the first holistic and comprehensive LID program in the tropics and holds promise for extension to other tropical cities. This paper presents a comprehensive summary of the goals, LID practices (ABC design features) and design considerations as well as results of several monitored sites, including a constructed wetland, two rain gardens, green roofs and three canal restoration projects. We evaluate the ABC Waters Program based on these initial results and consider the challenges, issues and the research needs for it to meet its hydrological and water quality remediation goals. So far, the ABC design features evaluated perform well in removing particulates. Performance in nutrient removal is poor. With over 60 projects completed within 10 years, post-project monitoring and evaluation is necessary and complements on-going laboratory and modelling research projects conducted by local academic institutions.

A potentiostat featuring an integrator transimpedance amplifier for the measurement of very low currents--Proof-of-principle application in microfluidic separations and voltammetry.

PubMed

Koutilellis, G D; Economou, A; Efstathiou, C E

2016-03-01

This work reports the design and construction of a novel potentiostat which features an integrator transimpedance amplifier as a current-monitoring unit. The integration approach addresses the limitations of the feedback resistor approach used for current monitoring in conventional potentiostat designs. In the present design, measurement of the current is performed by a precision switched integrator transimpedance amplifier operated in the dual sampling mode which enables sub-pA resolution. The potentiostat is suitable for measuring very low currents (typical dynamic range: 5 pA-4.7 μA) with a 16 bit resolution, and it can support 2-, 3- and 4-electrode cell configurations. Its operation was assessed by using it as a detection module in a home-made capillary electrophoresis system for the separation and amperometric detection of paracetamol and p-aminophenol at a 3-electrode microfluidic chip. The potential and limitations of the proposed potentiostat to implement fast potential-scan voltammetric techniques were demonstrated for the case of cyclic voltammetry.

A potentiostat featuring an integrator transimpedance amplifier for the measurement of very low currents—Proof-of-principle application in microfluidic separations and voltammetry

NASA Astrophysics Data System (ADS)

Koutilellis, G. D.; Economou, A.; Efstathiou, C. E.

2016-03-01

This work reports the design and construction of a novel potentiostat which features an integrator transimpedance amplifier as a current-monitoring unit. The integration approach addresses the limitations of the feedback resistor approach used for current monitoring in conventional potentiostat designs. In the present design, measurement of the current is performed by a precision switched integrator transimpedance amplifier operated in the dual sampling mode which enables sub-pA resolution. The potentiostat is suitable for measuring very low currents (typical dynamic range: 5 pA-4.7 μA) with a 16 bit resolution, and it can support 2-, 3- and 4-electrode cell configurations. Its operation was assessed by using it as a detection module in a home-made capillary electrophoresis system for the separation and amperometric detection of paracetamol and p-aminophenol at a 3-electrode microfluidic chip. The potential and limitations of the proposed potentiostat to implement fast potential-scan voltammetric techniques were demonstrated for the case of cyclic voltammetry.

Engineering and Design of the Steady Inductive Helicity Injected Torus (HIT--SI)

NASA Astrophysics Data System (ADS)

Sieck, P. E.; Jarboe, T. R.; Nelson, B. A.; Rogers, J. A.; Shumlak, U.

1999-11-01

Steady Inductive Helicity Injection (SIHI) is an inductive helicity injection method that injects helicity at a nearly constant rate, without open field lines, and without removing any helicity or magnetic energy from the plasma.(T.R. Jarboe, Fusion Technology, 36) (1), p. 85, 1999 SIHI directly produces a rotating magnetic field structure, and in the frame of the rotating field the current profile is nearly time independent. The Steady Inductive Helicity Injected Torus (HIT--SI) is a spheromak designed to implement SIHI so that the current profile in the rotating frame is optimized. The geometry of HIT--SI will be presented, including the manufacturing techniques and metallurgical processes planned for construction of the close-fitting flux conserver. The flux conserver is made of aged chromium copper with 80% the conductivity of pure copper. The detailed electrical insulation requirements in the helicity injector design lead to a complex o-ring seal and a plasma-sprayed alumina insulation coating. This has prompted the construction of an o-ring prototype test fixture having the main features of the o-ring design and the alumina coating. The design and evaluation of this fixture will also be presented with vacuum and voltage test results.

The Global Experience of Deployment of Energy-Efficient Technologies in High-Rise Construction

NASA Astrophysics Data System (ADS)

Potienko, Natalia D.; Kuznetsova, Anna A.; Solyakova, Darya N.; Klyueva, Yulia E.

2018-03-01

The objective of this research is to examine issues related to the increasing importance of energy-efficient technologies in high-rise construction. The aim of the paper is to investigate modern approaches to building design that involve implementation of various energy-saving technologies in diverse climates and at different structural levels, including the levels of urban development, functionality, planning, construction and engineering. The research methodology is based on the comprehensive analysis of the advanced global expertise in the design and construction of energy-efficient high-rise buildings, with the examination of their positive and negative features. The research also defines the basic principles of energy-efficient architecture. Besides, it draws parallels between the climate characteristics of countries that lead in the field of energy-efficient high-rise construction, on the one hand, and the climate in Russia, on the other, which makes it possible to use the vast experience of many countries, wholly or partially. The paper also gives an analytical review of the results arrived at by implementing energy efficiency principles into high-rise architecture. The study findings determine the impact of energy-efficient technologies on high-rise architecture and planning solutions. In conclusion, the research states that, apart from aesthetic and compositional interpretation of architectural forms, an architect nowadays has to address the task of finding a synthesis between technological and architectural solutions, which requires knowledge of advanced technologies. The study findings reveal that the implementation of modern energy-efficient technologies into high-rise construction is of immediate interest and is sure to bring long-term benefits.

77 FR 1780 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-11

... development--design and construction. Site utilities--design and construction. Stormwater facilities--design and construction. Airside/apron--design and construction. Landside/roadway--design and construction. General aviation terminal/apron--design and construction. Airport beacon relocation--design and...

Unique issues raised by drug benefit design.

PubMed

Berndt, Ernst R

2004-01-01

In this Perspective on the preceding paper by Joseph Newhouse, I point out a number of features of the pharmaceutical industry that differentiate it from other health care sectors. These differences help explain why it has proved to be so very difficult to construct policies that simultaneously contain health care costs, provide patients with high-quality care, and generate continued incentives for innovation. I then summarize Newhouse's preferred Medicare prescription drug benefit program and the issues it raises.

Precise laser gyroscope for autonomous inertial navigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuznetsov, A G; Molchanov, A V; Izmailov, E A

2015-01-31

Requirements to gyroscopes of strapdown inertial navigation systems for aircraft application are formulated. The construction of a ring helium – neon laser designed for autonomous navigation is described. The processes that determine the laser service life and the relation between the random error of the angular velocity measurement and the surface relief features of the cavity mirrors are analysed. The results of modelling one of the promising approaches to processing the laser gyroscope signals are presented. (laser gyroscopes)

[Dermatoglyphics in the prognostication of constitutional and physical traits in humans].

PubMed

Mazur, E S; Sidorenko, A G

2009-01-01

The present study was designed to elucidate the relationship between palmar and digital dermatoglyphic patterns and descriptive signs of human appearance based on the results of comprehensive anthropometric examination of 2620 men and 380 women. A battery of different methods were used to statistically treat the results of dactyloscopic records. They demonstrated correlation between skin patterns and external body features that can be used to construct diagnostic models for the purpose of personality identification.

Dreamy Draw Dam - Master Plan and Feature Design, New River and Phoenix City Streams, Arizona.

DTIC Science & Technology

1981-09-01

Carnegiea gigantea Saguaro Cactus Ferocactus wislizenii Fishhook Barrel Cactus The area north of the paved assembly area will be recontoured to...brittlebush, triangle bursage, little leaf palo verde, ocotillo, and various cacti species (pls. 8 and 9). Destructive past land uses have contributed to the...is well established. Plants used include saguaro , ocotillo, and Bermuda grass. The areas used for borrowing of material in construction of the 18 dam

A fully automated digitally controlled 30-inch telescope

NASA Technical Reports Server (NTRS)

Colgate, S. A.; Moore, E. P.; Carlson, R.

1975-01-01

A fully automated 30-inch (75-cm) telescope has been successfully designed and constructed from a military surplus Nike-Ajax radar mount. Novel features include: closed-loop operation between mountain telescope and campus computer 30 km apart via microwave link, a TV-type sensor which is photon shot-noise limited, a special lightweight primary mirror, and a stepping motor drive capable of slewing and settling one degree in one second or a radian in fifteen seconds.

KSC-2010-1158

NASA Image and Video Library

2010-01-08

CAPE CANAVERAL, Fla. - In Launch Complex 39 at NASA's Kennedy Space Center in Florida, construction workers survey the last outside wall of the Propellants North Administrative and Maintenance Facility. Concrete layers on either side of high-density foam insulation in the facility's walls will prevent any transfer of radiant heat between the exterior and interior of the buildings. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

Optimization of coastal protection measures on small islands in the northfrisian part of the North Sea

NASA Astrophysics Data System (ADS)

Wöffler, T.; Jensen, J.; Schüttrumpf, H.

2017-12-01

Low lying small islands are among the most vulnerable regions worldwide due to the consequences of climate change. The reasons for this are the concentration of infrastructure, geographical features and their small size. Worldwide special forms and adaptations of coastal protection strategies and measures can be found on small islands. In the northfrisian part of the North Sea worldwide unique strategies and measures have been developed in the last centuries due to the geographic location and the isolation during extreme events. One special feature of their coastal protection strategy is the lack of dikes. For this reason, the houses are built on artificial dwelling mounds in order to protect the inhabitants and their goods against frequently occurring inundations during storm surge seasons (up to 30 times a year). The Hallig islands themselves benefit by these inundations due to sediments, which are accumulated on the island's surfaces. This sedimentation has enabled a natural adaption to sea level rise in the past. Nevertheless, the construction methods of the coastal protection measures are mainly based on tradition and the knowledge of the inhabitants. No resilient design approaches and safety standards for these special structures like dwelling mounds and elevated revetments exist today. For this reason, neither a cost efficient construction nor a prioritization of measures is possible. Main part of this paper is the scientific investigation of the existing coastal protection measures with the objective of the development of design approaches and safety standards. The results will optimize the construction of the existing coastal protection measures and can be transferred to other small islands and low lying areas worldwide.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kung, C C; Brunkhorst, C; Greenough, N

Experimental results have shown that the high harmonic fast wave (HHFW) at 30 MHz can provide substantial plasma heating and current drive for the NSTX spherical tokamak operation. However, the present antenna strap design rarely achieves the design goal of delivering the full transmitter capability of 6 MW to the plasma. In order to deliver more power to the plasma, a new antenna strap design and the associated coaxial line feeds are being constructed. This new antenna strap design features two feedthroughs to replace the old single feed-through design. In the design process, CST Microwave Studio has been used tomore » simulate the entire new antenna strap structure including the enclosure and the Faraday shield. In this paper, the antenna strap model and the simulation results will be discussed in detail. The test results from the new antenna straps with their associated resonant loops will be presented as well.« less

Extended performance solar electric propulsion thrust system study. Volume 4: Thruster technology evaluation

NASA Technical Reports Server (NTRS)

Poeschel, R. L.; Hawthorne, E. I.; Weisman, Y. C.; Frisman, M.; Benson, G. C.; Mcgrath, R. J.; Martinelli, R. M.; Linsenbardt, T. L.; Beattie, J. R.

1977-01-01

Several thrust system design concepts were evaluated and compared using the specifications of the most advanced 30 cm engineering model thruster as the technology base. Emphasis was placed on relatively high power missions (60 to 100 kW) such as a Halley's comet rendezvous. The extensions in thruster performance required for the Halley's comet mission were defined and alternative thrust system concepts were designed in sufficient detail for comparing mass, efficiency, reliability, structure, and thermal characteristics. Confirmation testing and analysis of thruster and power processing components were performed, and the feasibility of satisfying extended performance requirements was verified. A baseline design was selected from the alternatives considered, and the design analysis and documentation were refined. The baseline thrust system design features modular construction, conventional power processing, and a concentrator solar array concept and is designed to interface with the Space Shuttle.

Extended performance solar electric propulsion thrust system study. Volume 2: Baseline thrust system

NASA Technical Reports Server (NTRS)

Poeschel, R. L.; Hawthorne, E. I.

1977-01-01

Several thrust system design concepts were evaluated and compared using the specifications of the most advanced 30- cm engineering model thruster as the technology base. Emphasis was placed on relatively high-power missions (60 to 100 kW) such as a Halley's comet rendezvous. The extensions in thruster performance required for the Halley's comet mission were defined and alternative thrust system concepts were designed in sufficient detail for comparing mass, efficiency, reliability, structure, and thermal characteristics. Confirmation testing and analysis of thruster and power-processing components were performed, and the feasibility of satisfying extended performance requirements was verified. A baseline design was selected from the alternatives considered, and the design analysis and documentation were refined. The baseline thrust system design features modular construction, conventional power processing, and a concentractor solar array concept and is designed to interface with the space shuttle.

Constructal vascularized structures

NASA Astrophysics Data System (ADS)

Cetkin, Erdal

2015-06-01

Smart features such as self-healing and selfcooling require bathing the entire volume with a coolant or/and healing agent. Bathing the entire volume is an example of point to area (or volume) flows. Point to area flows cover all the distributing and collecting kinds of flows, i.e. inhaling and exhaling, mining, river deltas, energy distribution, distribution of products on the landscape and so on. The flow resistances of a point to area flow can be decreased by changing the design with the guidance of the constructal law, which is the law of the design evolution in time. In this paper, how the flow resistances (heat, fluid and stress) can be decreased by using the constructal law is shown with examples. First, the validity of two assumptions is surveyed: using temperature independent Hess-Murray rule and using constant diameter ducts where the duct discharges fluid along its edge. Then, point to area types of flows are explained by illustrating the results of two examples: fluid networks and heating an area. Last, how the structures should be vascularized for cooling and mechanical strength is documented. This paper shows that flow resistances can be decreased by morphing the shape freely without any restrictions or generic algorithms.

Visualization of air flow around soccer ball using a particle image velocimetry

PubMed Central

Hong, Sungchan; Asai, Takeshi; Seo, Kazuya

2015-01-01

A traditional soccer ball is constructed using 32 pentagonal and hexagonal panels. In recent years, however, the likes of the Teamgeist and Jabulani balls, constructed from 14 and 8 panels, respectively, have entered the field, marking a significant departure from conventionality in terms of shape and design. Moreover, the recently introduced Brazuca ball features a new 6-panel design and has already been adopted by many soccer leagues. However, the shapes of the constituent panels of these balls differ substantially from those of conventional balls. Therefore, this study set out to investigate the flight and aerodynamic characteristics of different orientations of the soccer ball, which is constructed from panels of different shapes. A wind tunnel test showed substantial differences in the aerodynamic forces acting on the ball, depending on its orientation. Substantial differences were also observed in the aerodynamic forces acting on the ball in different directions, corresponding to its orientation and rotation. Moreover, two-dimensional particle image velocimetry (2D-PIV) measurements showed that the boundary separation varies depending on the orientation of the ball. Based on these results, we can conclude that the shape of the panels of a soccer ball substantially affects its flight trajectory. PMID:26446616

Construction of a WMR for trajectory tracking control: experimental results.

PubMed

Silva-Ortigoza, R; Márquez-Sánchez, C; Marcelino-Aranda, M; Marciano-Melchor, M; Silva-Ortigoza, G; Bautista-Quintero, R; Ramos-Silvestre, E R; Rivera-Díaz, J C; Muñoz-Carrillo, D

2013-01-01

This paper reports a solution for trajectory tracking control of a differential drive wheeled mobile robot (WMR) based on a hierarchical approach. The general design and construction of the WMR are described. The hierarchical controller proposed has two components: a high-level control and a low-level control. The high-level control law is based on an input-output linearization scheme for the robot kinematic model, which provides the desired angular velocity profiles that the WMR has to track in order to achieve the desired position (x∗, y∗) and orientation (φ∗). Then, a low-level control law, based on a proportional integral (PI) approach, is designed to control the velocity of the WMR wheels to ensure those tracking features. Regarding the trajectories, this paper provides the solution or the following cases: (1) time-varying parametric trajectories such as straight lines and parabolas and (2) smooth curves fitted by cubic splines which are generated by the desired data points {(x₁∗, y₁∗),..., (x(n)∗, y(n)∗)}. A straightforward algorithm is developed for constructing the cubic splines. Finally, this paper includes an experimental validation of the proposed technique by employing a DS1104 dSPACE electronic board along with MATLAB/Simulink software.

Construction of a WMR for Trajectory Tracking Control: Experimental Results

PubMed Central

Silva-Ortigoza, R.; Márquez-Sánchez, C.; Marcelino-Aranda, M.; Marciano-Melchor, M.; Silva-Ortigoza, G.; Bautista-Quintero, R.; Ramos-Silvestre, E. R.; Rivera-Díaz, J. C.; Muñoz-Carrillo, D.

2013-01-01

This paper reports a solution for trajectory tracking control of a differential drive wheeled mobile robot (WMR) based on a hierarchical approach. The general design and construction of the WMR are described. The hierarchical controller proposed has two components: a high-level control and a low-level control. The high-level control law is based on an input-output linearization scheme for the robot kinematic model, which provides the desired angular velocity profiles that the WMR has to track in order to achieve the desired position (x∗, y∗) and orientation (φ∗). Then, a low-level control law, based on a proportional integral (PI) approach, is designed to control the velocity of the WMR wheels to ensure those tracking features. Regarding the trajectories, this paper provides the solution or the following cases: (1) time-varying parametric trajectories such as straight lines and parabolas and (2) smooth curves fitted by cubic splines which are generated by the desired data points {(x1∗, y1∗),..., (xn∗, yn∗)}. A straightforward algorithm is developed for constructing the cubic splines. Finally, this paper includes an experimental validation of the proposed technique by employing a DS1104 dSPACE electronic board along with MATLAB/Simulink software. PMID:23997679

Visualization of air flow around soccer ball using a particle image velocimetry

NASA Astrophysics Data System (ADS)

Hong, Sungchan; Asai, Takeshi; Seo, Kazuya

2015-10-01

A traditional soccer ball is constructed using 32 pentagonal and hexagonal panels. In recent years, however, the likes of the Teamgeist and Jabulani balls, constructed from 14 and 8 panels, respectively, have entered the field, marking a significant departure from conventionality in terms of shape and design. Moreover, the recently introduced Brazuca ball features a new 6-panel design and has already been adopted by many soccer leagues. However, the shapes of the constituent panels of these balls differ substantially from those of conventional balls. Therefore, this study set out to investigate the flight and aerodynamic characteristics of different orientations of the soccer ball, which is constructed from panels of different shapes. A wind tunnel test showed substantial differences in the aerodynamic forces acting on the ball, depending on its orientation. Substantial differences were also observed in the aerodynamic forces acting on the ball in different directions, corresponding to its orientation and rotation. Moreover, two-dimensional particle image velocimetry (2D-PIV) measurements showed that the boundary separation varies depending on the orientation of the ball. Based on these results, we can conclude that the shape of the panels of a soccer ball substantially affects its flight trajectory.

ION Configuration Editor

NASA Technical Reports Server (NTRS)

Borgen, Richard L.

2013-01-01

The configuration of ION (Inter - planetary Overlay Network) network nodes is a manual task that is complex, time-consuming, and error-prone. This program seeks to accelerate this job and produce reliable configurations. The ION Configuration Editor is a model-based smart editor based on Eclipse Modeling Framework technology. An ION network designer uses this Eclipse-based GUI to construct a data model of the complete target network and then generate configurations. The data model is captured in an XML file. Intrinsic editor features aid in achieving model correctness, such as field fill-in, type-checking, lists of valid values, and suitable default values. Additionally, an explicit "validation" feature executes custom rules to catch more subtle model errors. A "survey" feature provides a set of reports providing an overview of the entire network, enabling a quick assessment of the model s completeness and correctness. The "configuration" feature produces the main final result, a complete set of ION configuration files (eight distinct file types) for each ION node in the network.

Activities of the Boom and Chassis Group

NASA Technical Reports Server (NTRS)

Dell, Jason Scott; Meeks, Thomas Bayne; Merkel, Kelly; Nelson, Brent; Winchell, Tom

1992-01-01

Group One of the NASA Lunar Enabler Project has designed the primary chassis and boom structures for the lunar vehicle. Both components also feature V-clamps that were adapted to interface connections within the structure. The chassis features a front end, rear end section, middle cross-section, and face plate. The rear section contains an extra compartment for the engine, hydraulic pump, fuel bottles, and oil reservoir necessary for the wheel drives. Each section consists of tubular aluminum 6061-T6. The boom features four degrees of freedom system, where the minimum factor of safety of any part is 1.5 (but, normally much higher). It consists of a tapered upper boom, lower boom, and three elbows that complement the articulation joints. Each section of the boom has been constructed from aluminum 6061-T6. There are four joints and eight V-clamps in the boom assembly. The V-clamps feature support rings that prevent axial rotation. They provide easy adaptability and assembly.

A Higher-Order Neural Network Design for Improving Segmentation Performance in Medical Image Series

NASA Astrophysics Data System (ADS)

Selvi, Eşref; Selver, M. Alper; Güzeliş, Cüneyt; Dicle, Oǧuz

2014-03-01

Segmentation of anatomical structures from medical image series is an ongoing field of research. Although, organs of interest are three-dimensional in nature, slice-by-slice approaches are widely used in clinical applications because of their ease of integration with the current manual segmentation scheme. To be able to use slice-by-slice techniques effectively, adjacent slice information, which represents likelihood of a region to be the structure of interest, plays critical role. Recent studies focus on using distance transform directly as a feature or to increase the feature values at the vicinity of the search area. This study presents a novel approach by constructing a higher order neural network, the input layer of which receives features together with their multiplications with the distance transform. This allows higher-order interactions between features through the non-linearity introduced by the multiplication. The application of the proposed method to 9 CT datasets for segmentation of the liver shows higher performance than well-known higher order classification neural networks.

Automatic Detection of Driver Fatigue Using Driving Operation Information for Transportation Safety

PubMed Central

Li, Zuojin; Chen, Liukui; Peng, Jun; Wu, Ying

2017-01-01

Fatigued driving is a major cause of road accidents. For this reason, the method in this paper is based on the steering wheel angles (SWA) and yaw angles (YA) information under real driving conditions to detect drivers’ fatigue levels. It analyzes the operation features of SWA and YA under different fatigue statuses, then calculates the approximate entropy (ApEn) features of a short sliding window on time series. Using the nonlinear feature construction theory of dynamic time series, with the fatigue features as input, designs a “2-6-6-3” multi-level back propagation (BP) Neural Networks classifier to realize the fatigue detection. An approximately 15-h experiment is carried out on a real road, and the data retrieved are segmented and labeled with three fatigue levels after expert evaluation, namely “awake”, “drowsy” and “very drowsy”. The average accuracy of 88.02% in fatigue identification was achieved in the experiment, endorsing the value of the proposed method for engineering applications. PMID:28587072

Automatic Detection of Driver Fatigue Using Driving Operation Information for Transportation Safety.

PubMed

Li, Zuojin; Chen, Liukui; Peng, Jun; Wu, Ying

2017-05-25

Fatigued driving is a major cause of road accidents. For this reason, the method in this paper is based on the steering wheel angles (SWA) and yaw angles (YA) information under real driving conditions to detect drivers' fatigue levels. It analyzes the operation features of SWA and YA under different fatigue statuses, then calculates the approximate entropy (ApEn) features of a short sliding window on time series. Using the nonlinear feature construction theory of dynamic time series, with the fatigue features as input, designs a "2-6-6-3" multi-level back propagation (BP) Neural Networks classifier to realize the fatigue detection. An approximately 15-h experiment is carried out on a real road, and the data retrieved are segmented and labeled with three fatigue levels after expert evaluation, namely "awake", "drowsy" and "very drowsy". The average accuracy of 88.02% in fatigue identification was achieved in the experiment, endorsing the value of the proposed method for engineering applications.

Designing attractive models via automated identification of chaotic and oscillatory dynamical regimes.

PubMed

Silk, Daniel; Kirk, Paul D W; Barnes, Chris P; Toni, Tina; Rose, Anna; Moon, Simon; Dallman, Margaret J; Stumpf, Michael P H

2011-10-04

Chaos and oscillations continue to capture the interest of both the scientific and public domains. Yet despite the importance of these qualitative features, most attempts at constructing mathematical models of such phenomena have taken an indirect, quantitative approach, for example, by fitting models to a finite number of data points. Here we develop a qualitative inference framework that allows us to both reverse-engineer and design systems exhibiting these and other dynamical behaviours by directly specifying the desired characteristics of the underlying dynamical attractor. This change in perspective from quantitative to qualitative dynamics, provides fundamental and new insights into the properties of dynamical systems.

Biomimicry in metal-organic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, MW; Gu, ZY; Bosch, M

2015-06-15

Nature has evolved a great number of biological molecules which serve as excellent constructional or functional units for metal-organic materials (MOMs). Even though the study of biomimetic MOMs is still at its embryonic stage, considerable progress has been made in the past few years. In this critical review, we will highlight the recent advances in the design, development and application of biomimetic MOMs, and illustrate how the incorporation of biological components into MOMs could further enrich their structural and functional diversity. More importantly, this review will provide a systematic overview of different methods for rational design of MOMs with biomimeticmore » features. Published by Elsevier B.V.« less

Construction and performance of MEGAs low-mass, high-rate cylindrical MWPCs

NASA Astrophysics Data System (ADS)

Cooper, M. D.; Armijo, V.; Black, J. K.; Bolton, R. D.; Carius, S.; Espinoza, C.; Hart, G.; Hogan, G. E.; Gonzales, A.; Kroupa, M. A.; Mischke, R. E.; Sandoval, J.; Schilling, S.; Sena, J.; Suazo, G.; Whitehouse, D. A.; Wilkinson, C. A.; Stantz, K.; Szymanski, J. J.; Jui, C. C.; Gagliardi, C. A.; Tribble, R. E.; Tu, X.-L.; Fisk, R. J.; Koetke, D. D.; Manweiler, R. W.; Nord, P. M.; Stanislaus, S.; Piilonen, L. E.; Zhang, Y. D.

A design for extremely low mass, high-resolution multiwire proportional chambers (MWPC) was achieved by the MEGA collaboration in its experiment to search for the lepton family number violating decay μ→eγ. To extend the present branching ratio limit by over an order of magnitude, these MWPCs were operated in high particle fluxes. They showed minimal effects of aging, and evidenced spatial and energy resolutions for the orbiting positrons from muon decay which were consistent with our design parameters. The unique features of these chambers, their assembly into the MEGA positron spectrometer, and their performance during the experiment are described in this paper.

Design & implementation of distributed spatial computing node based on WPS

NASA Astrophysics Data System (ADS)

Liu, Liping; Li, Guoqing; Xie, Jibo

2014-03-01

Currently, the research work of SIG (Spatial Information Grid) technology mostly emphasizes on the spatial data sharing in grid environment, while the importance of spatial computing resources is ignored. In order to implement the sharing and cooperation of spatial computing resources in grid environment, this paper does a systematical research of the key technologies to construct Spatial Computing Node based on the WPS (Web Processing Service) specification by OGC (Open Geospatial Consortium). And a framework of Spatial Computing Node is designed according to the features of spatial computing resources. Finally, a prototype of Spatial Computing Node is implemented and the relevant verification work under the environment is completed.

Streamlined Total Synthesis of Trioxacarcins and Its Application to the Design, Synthesis, and Biological Evaluation of Analogues Thereof. Discovery of Simpler Designed and Potent Trioxacarcin Analogues.

PubMed

Nicolaou, K C; Chen, Pengxi; Zhu, Shugao; Cai, Quan; Erande, Rohan D; Li, Ruofan; Sun, Hongbao; Pulukuri, Kiran Kumar; Rigol, Stephan; Aujay, Monette; Sandoval, Joseph; Gavrilyuk, Julia

2017-11-01

A streamlined total synthesis of the naturally occurring antitumor agents trioxacarcins is described, along with its application to the construction of a series of designed analogues of these complex natural products. Biological evaluation of the synthesized compounds revealed a number of highly potent, and yet structurally simpler, compounds that are effective against certain cancer cell lines, including a drug-resistant line. A novel one-step synthesis of anthraquinones and chloro anthraquinones from simple ketone precursors and phenylselenyl chloride is also described. The reported work, featuring novel chemistry and cascade reactions, has potential applications in cancer therapy, including targeted approaches as in antibody-drug conjugates.

A typewriting system operated by head movements, based on home-computer equipment.

PubMed

Heuvelmans, A M; Mélotte, H E; Neve, J J

1990-06-01

For persons who cannot move their hands and legs we have designed a relatively inexpensive typewriting system which can be operated by movements of the head. The typewriter is made up of commercially available home computer equipment - i e, a computer including monitor and printer and a headset replacing the mouse. A user-friendly software program has been designed to replace the mouse button and to make this equipment act as a typewriter with simple text-editing features. Some ergonomics aspects of the typewriter set-up and the results of an evaluation of the typewriter by two patients suffering from amyotrophic lateral sclerosis (ALS) are given. Several factors relevant to the design, construction, evaluation and application of the typewriter are discussed.

Stressed photoconductive detector for far-infrared space applications

NASA Technical Reports Server (NTRS)

Wang, J.-Q.; Richards, P. L.; Beeman, J. W.; Haller, E. E.

1987-01-01

An optimized leaf-spring apparatus for applying uniaxial stress to a Ge:Ga far-IR photoconductor has been designed and tested. This design has significant advantages for space applications which require high quantum efficiency and stable operation over long periods of time. The important features include adequate spring deflection with relatively small overall size, torque-free stress, easy measurement of applied stress, and a detector configuration with high responsivity. One-dimensional arrays of stressed photoconductors can be constructed using this design. A peak responsivity of 38 A/W is achieved in a detector with a cutoff wavelength of 200 microns, which was operated at a temperature of 2.0 K and a bias voltage equal to one-half of the breakdown voltage.

The Proposed 2 MeV Electron Cooler for COSY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dietrich, Juergen; Parkhomchuk, Vasily V.; Reva, Vladimir B.

2006-03-20

The design, construction and installation of a 2 MeV electron cooling system for COSY is proposed to further boost the luminosity even with strong heating effects of high-density internal targets. In addition the design of the 2 MeV electron cooler for COSY is intended to test some new features of the high energy electron cooler for HESR at GSI. The design of the 2 MeV electron cooler will be accomplished in cooperation with the Budker Institute of Nuclear Physics in Novosibirsk, Russia. Starting with the boundary conditions of the existing electron cooler at COSY the requirements and a first generalmore » scheme of the 2 MeV electron cooler are described.« less

PLAID- A COMPUTER AIDED DESIGN SYSTEM

NASA Technical Reports Server (NTRS)

Brown, J. W.

1994-01-01

PLAID is a three-dimensional Computer Aided Design (CAD) system which enables the user to interactively construct, manipulate, and display sets of highly complex geometric models. PLAID was initially developed by NASA to assist in the design of Space Shuttle crewstation panels, and the detection of payload object collisions. It has evolved into a more general program for convenient use in many engineering applications. Special effort was made to incorporate CAD techniques and features which minimize the users workload in designing and managing PLAID models. PLAID consists of three major modules: the Primitive Object Generator (BUILD), the Composite Object Generator (COG), and the DISPLAY Processor. The BUILD module provides a means of constructing simple geometric objects called primitives. The primitives are created from polygons which are defined either explicitly by vertex coordinates, or graphically by use of terminal crosshairs or a digitizer. Solid objects are constructed by combining, rotating, or translating the polygons. Corner rounding, hole punching, milling, and contouring are special features available in BUILD. The COG module hierarchically organizes and manipulates primitives and other previously defined COG objects to form complex assemblies. The composite object is constructed by applying transformations to simpler objects. The transformations which can be applied are scalings, rotations, and translations. These transformations may be defined explicitly or defined graphically using the interactive COG commands. The DISPLAY module enables the user to view COG assemblies from arbitrary viewpoints (inside or outside the object) both in wireframe and hidden line renderings. The PLAID projection of a three-dimensional object can be either orthographic or with perspective. A conflict analysis option enables detection of spatial conflicts or collisions. DISPLAY provides camera functions to simulate a view of the model through different lenses. Other features include hardcopy plot generation, scaling and zoom options, distance tabulations, and descriptive text in different sizes and fonts. An object in the PLAID database is not just a collection of lines; rather, it is a true three-dimensional representation from which correct hidden line renditions can be computed for any specified eye point. The drawings produced in the various modules of PLAID can be stored in files for future use. The PLAID program product is available by license for a period of 10 years to domestic U.S. licensees. The licensed program product includes the PLAID source code, command procedures, sample applications, and one set of supporting documentation. Copies of the documentation may be purchased separately at the price indicated below. PLAID is written in FORTRAN 77 for single user interactive execution and has been implemented on a DEC VAX series computer operating under VMS with a recommended core memory of four megabytes. PLAID requires a Tektronix 4014 compatible graphics display terminal and optionally uses a Tektronix 4631 compatible graphics hardcopier. Plots of resulting PLAID displays may be produced using the Calcomp 960, HP 7221, or HP 7580 plotters. Digitizer tablets can also be supported. This program was developed in 1986.

Influence of winding construction on starter-generator thermal processes

NASA Astrophysics Data System (ADS)

Grachev, P. Yu; Bazarov, A. A.; Tabachinskiy, A. S.

2018-01-01

Dynamic processes in starter-generators features high winding are overcurrent. It can lead to insulation overheating and fault operation mode. For hybrid and electric vehicles, new high efficiency construction of induction machines windings is proposed. Stator thermal processes need be considered in the most difficult operation modes. The article describes construction features of new compact stator windings, electromagnetic and thermal models of processes in stator windings and explains the influence of innovative construction on thermal processes. Models are based on finite element method.

Trend analysis of modern high-rise construction

NASA Astrophysics Data System (ADS)

Radushinsky, Dmitry; Gubankov, Andrey; Mottaeva, Asiiat

2018-03-01

The article reviews the main trends of modern high-rise construction considered a number of architectural, engineering and technological, economic and image factors that have influenced the intensification of construction of high-rise buildings in the 21st century. The key factors of modern high-rise construction are identified, which are associated with an attractive image component for businessmen and politicians, with the ability to translate current views on architecture and innovations in construction technologies and the lobbying of relevant structures, as well as the opportunity to serve as an effective driver in the development of a complex of national economy sectors with the achievement of a multiplicative effect. The estimation of the priority nature of participation of foreign architectural bureaus in the design of super-high buildings in Russia at the present stage is given. The issue of economic expediency of construction of high-rise buildings, including those with only a residential function, has been investigated. The connection between the construction of skyscrapers as an important component of the image of cities in the marketing of places and territories, the connection of the availability of a high-rise center, the City, with the possibilities of attracting a "creative class" and the features of creating a large working space for specialists on the basis of territorial proximity and density of high-rise buildings.

Particle systems for adaptive, isotropic meshing of CAD models

PubMed Central

Levine, Joshua A.; Whitaker, Ross T.

2012-01-01

We present a particle-based approach for generating adaptive triangular surface and tetrahedral volume meshes from computer-aided design models. Input shapes are treated as a collection of smooth, parametric surface patches that can meet non-smoothly on boundaries. Our approach uses a hierarchical sampling scheme that places particles on features in order of increasing dimensionality. These particles reach a good distribution by minimizing an energy computed in 3D world space, with movements occurring in the parametric space of each surface patch. Rather than using a pre-computed measure of feature size, our system automatically adapts to both curvature as well as a notion of topological separation. It also enforces a measure of smoothness on these constraints to construct a sizing field that acts as a proxy to piecewise-smooth feature size. We evaluate our technique with comparisons against other popular triangular meshing techniques for this domain. PMID:23162181

Sensitive Nonenzymatic Electrochemical Glucose Detection Based on Hollow Porous NiO

NASA Astrophysics Data System (ADS)

He, Gege; Tian, Liangliang; Cai, Yanhua; Wu, Shenping; Su, Yongyao; Yan, Hengqing; Pu, Wanrong; Zhang, Jinkun; Li, Lu

2018-01-01

Transition metal oxides (TMOs) have attracted extensive research attentions as promising electrocatalytic materials. Despite low cost and high stability, the electrocatalytic activity of TMOs still cannot satisfy the requirements of applications. Inspired by kinetics, the design of hollow porous structure is considered as a promising strategy to achieve superior electrocatalytic performance. In this work, cubic NiO hollow porous architecture (NiO HPA) was constructed through coordinating etching and precipitating (CEP) principle followed by post calcination. Being employed to detect glucose, NiO HPA electrode exhibits outstanding electrocatalytic activity in terms of high sensitivity (1323 μA mM-1 cm-2) and low detection limit (0.32 μM). The excellent electrocatalytic activity can be ascribed to large specific surface area (SSA), ordered diffusion channels, and accelerated electron transfer rate derived from the unique hollow porous features. The results demonstrate that the NiO HPA could have practical applications in the design of nonenzymatic glucose sensors. The construction of hollow porous architecture provides an effective nanoengineering strategy for high-performance electrocatalysts.

Constructing a generalized network design model to study air distribution in ventilation networks in subway with a single-track tunnel

NASA Astrophysics Data System (ADS)

Lugin, IV

2018-03-01

In focus are the features of construction of the generalized design model for the network method to study air distribution in ventilation system in subway with the single-track tunnel. The generalizations, assumptions and simplifications included in the model are specified. The air distribution is calculated with regard to the influence of topology and air resistances of the ventilation network sections. The author studies two variants of the subway line: half-open and closed with dead end on the both sides. It is found that the total air exchange at a subway station depends on the station location within the line. The operating mode of fans remains unaltered in this case. The article shows that elimination of air leakage in the station ventilation room allows an increase in the air flow rate by 7–8% at the same energy consumption by fans. The influence of the stop of a train in the tunnel on the air distribution is illustrated.

BAMS2 Workspace: a comprehensive and versatile neuroinformatic platform for collating and processing neuroanatomical connections

PubMed Central

Bota, Mihail; Talpalaru, Ştefan; Hintiryan, Houri; Dong, Hong-Wei; Swanson, Larry W.

2014-01-01

We present in this paper a novel neuroinformatic platform, the BAMS2 Workspace (http://brancusi1.usc.edu), designed for storing and processing information about gray matter region axonal connections. This de novo constructed module allows registered users to directly collate their data by using a simple and versatile visual interface. It also allows construction and analysis of sets of connections associated with gray matter region nomenclatures from any designated species. The Workspace includes a set of tools allowing the display of data in matrix and networks formats, and the uploading of processed information in visual, PDF, CSV, and Excel formats. Finally, the Workspace can be accessed anonymously by third party systems to create individualized connectivity networks. All features of the BAMS2 Workspace are described in detail, and are demonstrated with connectivity reports collated in BAMS and associated with the rat sensory-motor cortex, medial frontal cortex, and amygdalar regions. PMID:24668342

Predicting hot spots in protein interfaces based on protrusion index, pseudo hydrophobicity and electron-ion interaction pseudopotential features

PubMed Central

Xia, Junfeng; Yue, Zhenyu; Di, Yunqiang; Zhu, Xiaolei; Zheng, Chun-Hou

2016-01-01

The identification of hot spots, a small subset of protein interfaces that accounts for the majority of binding free energy, is becoming more important for the research of drug design and cancer development. Based on our previous methods (APIS and KFC2), here we proposed a novel hot spot prediction method. For each hot spot residue, we firstly constructed a wide variety of 108 sequence, structural, and neighborhood features to characterize potential hot spot residues, including conventional ones and new one (pseudo hydrophobicity) exploited in this study. We then selected 3 top-ranking features that contribute the most in the classification by a two-step feature selection process consisting of minimal-redundancy-maximal-relevance algorithm and an exhaustive search method. We used support vector machines to build our final prediction model. When testing our model on an independent test set, our method showed the highest F1-score of 0.70 and MCC of 0.46 comparing with the existing state-of-the-art hot spot prediction methods. Our results indicate that these features are more effective than the conventional features considered previously, and that the combination of our and traditional features may support the creation of a discriminative feature set for efficient prediction of hot spots in protein interfaces. PMID:26934646

The Influences of Landscape Features on Visitation of Hospital Green Spaces—A Choice Experiment Approach

PubMed Central

Chang, Kaowen Grace; Chien, Hungju

2017-01-01

Studies have suggested that visiting and viewing landscaping at hospitals accelerates patient’s recovery from surgery and help staff’s recovery from mental fatigue. To plan and construct such landscapes, we need to unravel landscape features desirable to different groups so that the space can benefit a wide range of hospital users. Using discrete choice modeling, we developed experimental choice sets to investigate how landscape features influence the visitations of different users in a large regional hospital in Taiwan. The empirical survey provides quantitative estimates of the influence of each landscape feature on four user groups, including patients, caregivers, staff, and neighborhood residents. Our findings suggest that different types of features promote visits from specific user groups. Landscape features facilitating physical activities effectively encourage visits across user groups especially for caregivers and staff. Patients in this study specify a strong need for contact with nature. The nearby community favors the features designed for children’s play and family activities. People across user groups value the features that provide a mitigated microclimate of comfort, such as a shelter. Study implications and limitations are also discussed. Our study provides information essential for creating a better healing environment in a hospital setting. PMID:28678168

The potential of value management (VM) to improve the consideration of energy efficiency within pre-construction

NASA Astrophysics Data System (ADS)

Tahir, Mohamad Zamhari; Nawi, Mohd Nasrun Mohd; Rajemi, Mohamad Farizal

2016-08-01

Energy demand and consumption in buildings will rise rapidly in the near future because of several social economics factors and this situation occurs not only in developed countries but also in developing countries such as Malaysia. There is demand towards building with energy efficiency features at this time, however most of the current buildings types are still being constructed with conventional designs, thus contribute to inefficient of energy consumption during the operation stage of the building. This paper presents the concept and the application of Value Management (VM) approach and its potential to improve consideration of energy efficiency within pre-construction process. Based on the relevant literatures, VM has provides an efficient and effective delivery system to fulfill the objectives and client's requirements. Generally in this paper, VM is discussed and scrutinized with reference to previous studies to see how these concepts contribute to better optimize the energy consumption in a building by seeking the best value energy efficiency through the design and construction process. This paper will not draw any conclusion but rather a preliminary research to propose the most energy efficiency measures to reliably accomplish a function that will meet the client's needs, desires and expectations. For further research in future, simple quantitative industry survey and VM workshops will be conducted to validate and further improve the research.

In pursuit of rigour and accountability in participatory design☆

PubMed Central

Frauenberger, Christopher; Good, Judith; Fitzpatrick, Geraldine; Iversen, Ole Sejer

2015-01-01

The field of Participatory Design (PD) has greatly diversified and we see a broad spectrum of approaches and methodologies emerging. However, to foster its role in designing future interactive technologies, a discussion about accountability and rigour across this spectrum is needed. Rejecting the traditional, positivistic framework, we take inspiration from related fields such as Design Research and Action Research to develop interpretations of these concepts that are rooted in PD׳s own belief system. We argue that unlike in other fields, accountability and rigour are nuanced concepts that are delivered through debate, critique and reflection. A key prerequisite for having such debates is the availability of a language that allows designers, researchers and practitioners to construct solid arguments about the appropriateness of their stances, choices and judgements. To this end, we propose a “tool-to-think-with” that provides such a language by guiding designers, researchers and practitioners through a process of systematic reflection and critical analysis. The tool proposes four lenses to critically reflect on the nature of a PD effort: epistemology, values, stakeholders and outcomes. In a subsequent step, the coherence between the revealed features is analysed and shows whether they pull the project in the same direction or work against each other. Regardless of the flavour of PD, we argue that this coherence of features indicates the level of internal rigour of PD work and that the process of reflection and analysis provides the language to argue for it. We envision our tool to be useful at all stages of PD work: in the planning phase, as part of a reflective practice during the work, and as a means to construct knowledge and advance the field after the fact. We ground our theoretical discussions in a specific PD experience, the ECHOES project, to motivate the tool and to illustrate its workings. PMID:26109833

Software model of a machine vision system based on the common house fly.

PubMed

Madsen, Robert; Barrett, Steven; Wilcox, Michael

2005-01-01

The vision system of the common house fly has many properties, such as hyperacuity and parallel structure, which would be advantageous in a machine vision system. A software model has been developed which is ultimately intended to be a tool to guide the design of an analog real time vision system. The model starts by laying out cartridges over an image. The cartridges are analogous to the ommatidium of the fly's eye and contain seven photoreceptors each with a Gaussian profile. The spacing between photoreceptors is variable providing for more or less detail as needed. The cartridges provide information on what type of features they see and neighboring cartridges share information to construct a feature map.

Heat amplification and negative differential thermal conductance in a strongly coupled nonequilibrium spin-boson system

NASA Astrophysics Data System (ADS)

Wang, Chen; Chen, Xu-Min; Sun, Ke-Wei; Ren, Jie

2018-05-01

We investigate the nonequilibrium quantum heat transfer in a quantum thermal transistor, constructed by a triangle-coupled spin-boson system in a three-terminal setup. By exploiting the nonequilibrium noninteracting blip approximation approach combined with full counting statistics, we obtain the steady-state thermal transport, such as heat currents. We identify the giant heat amplification feature in a strong coupling regime, which results from the negative differential thermal conductance with respect to the gate temperature. Analysis shows that the strong coupling between the gate qubit and corresponding gate thermal bath plays the crucial role in exhibiting these far-from-equilibrium features. These results would have potential implications in designing efficient quantum thermal transistors in the future.

Predicting Presynaptic and Postsynaptic Neurotoxins by Developing Feature Selection Technique

PubMed Central

Yang, Yunchun; Zhang, Chunmei; Chen, Rong; Huang, Po

2017-01-01

Presynaptic and postsynaptic neurotoxins are proteins which act at the presynaptic and postsynaptic membrane. Correctly predicting presynaptic and postsynaptic neurotoxins will provide important clues for drug-target discovery and drug design. In this study, we developed a theoretical method to discriminate presynaptic neurotoxins from postsynaptic neurotoxins. A strict and objective benchmark dataset was constructed to train and test our proposed model. The dipeptide composition was used to formulate neurotoxin samples. The analysis of variance (ANOVA) was proposed to find out the optimal feature set which can produce the maximum accuracy. In the jackknife cross-validation test, the overall accuracy of 94.9% was achieved. We believe that the proposed model will provide important information to study neurotoxins. PMID:28303250

Design of the environment of care for safety of patients and personnel: does form follow function or vice versa in the intensive care unit?

PubMed

Bartley, Judene; Streifel, Andrew J

2010-08-01

We review the context of the environment of care in the intensive care unit setting in relation to patient safety and quality, specifically addressing healthcare-associated infection issues and solutions involving interdisciplinary teams. Issues addressed include current and future architectural design and layout trends, construction trends affecting intensive care units, and prevention of construction-associated healthcare-associated infections related to airborne and waterborne risks and design solutions. Specific elements include single-occupancy, acuity-scalable intensive care unit rooms; environmental aspects of hand hygiene, such as water risks, sink design/location, human waste management, surface selection (floor covering, countertops, furniture, and equipment) and cleaning, antimicrobial-treated or similar materials, ultraviolet germicidal irradiation, specialized rooms (airborne infection isolation and protective environments), and water system design and strategies for safe use of potable water and mitigation of water intrusion. Effective design and operational use of the intensive care unit environment of care must engage critical care personnel from initial planning and design through occupancy of the new/renovated intensive care unit as part of the infection control risk assessment team. The interdisciplinary infection control risk assessment team can address key environment of care design features to enhance the safety of intensive care unit patients, personnel, and visitors. This perspective will ensure the environment of care supports human factors and behavioral aspects of the interaction between the environment of care and its occupants.

Neural signal processing and closed-loop control algorithm design for an implanted neural recording and stimulation system.

PubMed

Hamilton, Lei; McConley, Marc; Angermueller, Kai; Goldberg, David; Corba, Massimiliano; Kim, Louis; Moran, James; Parks, Philip D; Sang Chin; Widge, Alik S; Dougherty, Darin D; Eskandar, Emad N

2015-08-01

A fully autonomous intracranial device is built to continually record neural activities in different parts of the brain, process these sampled signals, decode features that correlate to behaviors and neuropsychiatric states, and use these features to deliver brain stimulation in a closed-loop fashion. In this paper, we describe the sampling and stimulation aspects of such a device. We first describe the signal processing algorithms of two unsupervised spike sorting methods. Next, we describe the LFP time-frequency analysis and feature derivation from the two spike sorting methods. Spike sorting includes a novel approach to constructing a dictionary learning algorithm in a Compressed Sensing (CS) framework. We present a joint prediction scheme to determine the class of neural spikes in the dictionary learning framework; and, the second approach is a modified OSort algorithm which is implemented in a distributed system optimized for power efficiency. Furthermore, sorted spikes and time-frequency analysis of LFP signals can be used to generate derived features (including cross-frequency coupling, spike-field coupling). We then show how these derived features can be used in the design and development of novel decode and closed-loop control algorithms that are optimized to apply deep brain stimulation based on a patient's neuropsychiatric state. For the control algorithm, we define the state vector as representative of a patient's impulsivity, avoidance, inhibition, etc. Controller parameters are optimized to apply stimulation based on the state vector's current state as well as its historical values. The overall algorithm and software design for our implantable neural recording and stimulation system uses an innovative, adaptable, and reprogrammable architecture that enables advancement of the state-of-the-art in closed-loop neural control while also meeting the challenges of system power constraints and concurrent development with ongoing scientific research designed to define brain network connectivity and neural network dynamics that vary at the individual patient level and vary over time.

Robust Segmentation of Planar and Linear Features of Terrestrial Laser Scanner Point Clouds Acquired from Construction Sites.

PubMed

Maalek, Reza; Lichti, Derek D; Ruwanpura, Janaka Y

2018-03-08

Automated segmentation of planar and linear features of point clouds acquired from construction sites is essential for the automatic extraction of building construction elements such as columns, beams and slabs. However, many planar and linear segmentation methods use scene-dependent similarity thresholds that may not provide generalizable solutions for all environments. In addition, outliers exist in construction site point clouds due to data artefacts caused by moving objects, occlusions and dust. To address these concerns, a novel method for robust classification and segmentation of planar and linear features is proposed. First, coplanar and collinear points are classified through a robust principal components analysis procedure. The classified points are then grouped using a new robust clustering method, the robust complete linkage method. A robust method is also proposed to extract the points of flat-slab floors and/or ceilings independent of the aforementioned stages to improve computational efficiency. The applicability of the proposed method is evaluated in eight datasets acquired from a complex laboratory environment and two construction sites at the University of Calgary. The precision, recall, and accuracy of the segmentation at both construction sites were 96.8%, 97.7% and 95%, respectively. These results demonstrate the suitability of the proposed method for robust segmentation of planar and linear features of contaminated datasets, such as those collected from construction sites.

Robust Segmentation of Planar and Linear Features of Terrestrial Laser Scanner Point Clouds Acquired from Construction Sites

PubMed Central

Maalek, Reza; Lichti, Derek D; Ruwanpura, Janaka Y

2018-01-01

Automated segmentation of planar and linear features of point clouds acquired from construction sites is essential for the automatic extraction of building construction elements such as columns, beams and slabs. However, many planar and linear segmentation methods use scene-dependent similarity thresholds that may not provide generalizable solutions for all environments. In addition, outliers exist in construction site point clouds due to data artefacts caused by moving objects, occlusions and dust. To address these concerns, a novel method for robust classification and segmentation of planar and linear features is proposed. First, coplanar and collinear points are classified through a robust principal components analysis procedure. The classified points are then grouped using a new robust clustering method, the robust complete linkage method. A robust method is also proposed to extract the points of flat-slab floors and/or ceilings independent of the aforementioned stages to improve computational efficiency. The applicability of the proposed method is evaluated in eight datasets acquired from a complex laboratory environment and two construction sites at the University of Calgary. The precision, recall, and accuracy of the segmentation at both construction sites were 96.8%, 97.7% and 95%, respectively. These results demonstrate the suitability of the proposed method for robust segmentation of planar and linear features of contaminated datasets, such as those collected from construction sites. PMID:29518062

On the bending of structural materials with plastic anisotropic effect

NASA Astrophysics Data System (ADS)

Lachugin, D. V.; Pavilaynen, G. V.

2018-05-01

The study of a deformation features of metal alloys which are sensitive to tension or compression loading is an important technical challenge in the design and creation of a new shipbuilding and aircraft constructions. We use a mathematical model for the elastic-plastic bending of such material where SD(strength-different) parameter is taken into account. The problem is solved analytically and numerically. As an example of the material with the SD-effect the steel alloy is considered.

[The advance in synthetic biology: towards a microbe-derived paclitaxel intermediates].

PubMed

Wang, Wei; Yang, Yan; Zheng, Xiao-Dong; Huang, Shu-Qiong; Guo, Lei; Kong, Jian-Qiang; Cheng, Ke-Di

2013-02-01

The synthetic biology matures to promote the heterologous biosynthesis of the well-known drug paclitaxel that is one of the most important and active chemotherapeutic agents for the first-line clinical treatment of cancer. This review focuses on the construction and regulation of the biosynthetic pathway of paclitaxel intermediates in both Escherichia coli and Saccharomyces cerevisiae. In particular, the review also features the early efforts to design and overproduce taxadiene and the bottleneck of scale fermentation for producing the intermediates.

Note: Rigid holder to host and bend a crystal for multiple volume reflection of a particle beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carassiti, V.; Melchiorri, M.; Dalpiaz, P.

2010-06-15

A holder to lodge and bend a silicon crystal to excite multivolume reflection of a high-energy particle beam has been designed and fabricated. A mechanically robust and stable structure fastens a crystal at best condition for experiments. The holder has allowed the observation of 12-time repeated volume reflection with very high efficiency. We detail the most important features behind the construction of the holder together with the characterization of the crystal being bent by the holder.

Solid Modeling Aerospace Research Tool (SMART) user's guide, version 2.0

NASA Technical Reports Server (NTRS)

Mcmillin, Mark L.; Spangler, Jan L.; Dahmen, Stephen M.; Rehder, John J.

1993-01-01

The Solid Modeling Aerospace Research Tool (SMART) software package is used in the conceptual design of aerospace vehicles. It provides a highly interactive and dynamic capability for generating geometries with Bezier cubic patches. Features include automatic generation of commonly used aerospace constructs (e.g., wings and multilobed tanks); cross-section skinning; wireframe and shaded presentation; area, volume, inertia, and center-of-gravity calculations; and interfaces to various aerodynamic and structural analysis programs. A comprehensive description of SMART and how to use it is provided.

A high-compression electron gun for C6+ production: concept, simulations and mechanical design

NASA Astrophysics Data System (ADS)

Mertzig, Robert; Breitenfeldt, M.; Mathot, S.; Pitters, J.; Shornikov, A.; Wenander, F.

2017-07-01

In this paper we report on simulations and the mechanical design of a high-compression electron gun for an Electron Beam Ion Source (EBIS) dedicated for production of high intensity and high repetition rate pulses of bare carbon ions for injection into linac-based hadron therapy facilities. The gun is presently under construction at CERN to be retrofitted into the TwinEBIS test bench for experimental studies. We describe the design constraints, show results of numeric simulations and report on the mechanical design featuring several novel ideas. The reported design makes use of combined-function units with reduced number of mechanical joints that were carefully controlled and tuned during the manufacturing phase. The simulations addressed a wide range of topics including the influence of thermal effects, focusing optics, symmetry-breaking misalignments and injection into a full 5 T field.

The NASA Langley Laminar-Flow-Control (LFC) experiment on a swept, supercritical airfoil: Design overview

NASA Technical Reports Server (NTRS)

Harris, Charles D.; Harvey, William D.; Brooks, Cuyler W., Jr.

1988-01-01

A large-chord, swept, supercritical, laminar-flow-control (LFC) airfoil was designed and constructed and is currently undergoing tests in the Langley 8 ft Transonic Pressure Tunnel. The experiment was directed toward evaluating the compatibility of LFC and supercritical airfoils, validating prediction techniques, and generating a data base for future transport airfoil design as part of NASA's ongoing research program to significantly reduce drag and increase aircraft efficiency. Unique features of the airfoil included a high design Mach number with shock free flow and boundary layer control by suction. Special requirements for the experiment included modifications to the wind tunnel to achieve the necessary flow quality and contouring of the test section walls to simulate free air flow about a swept model at transonic speeds. Design of the airfoil with a slotted suction surface, the suction system, and modifications to the tunnel to meet test requirements are discussed.

Design, Project Execution, and Commissioning of the 1.8 K Superfluid Helium Refrigeration System for SRF Cryomodule Testing

DOE PAGES

Treite, P.; Nuesslein, U.; Jia, Yi; ...

2015-07-15

The Fermilab Cryomodule Test Facility (CMTF) provides a test bed to measure the performance of superconducting radiofrequency (SRF) cryomodules (CM). These SRF components form the basic building blocks of future high intensity accelerators such as the International Linear Collider (ILC) and a Muon Collider. Linde Kryotechnik AG and Linde Cryogenics have designed, constructed and commissioned the superfluid helium refrigerator needed to support SRF component testing at the CMTF Facility. The hybrid refrigerator is designed to operate in a variety of modes and under a wide range of boundary conditions down to 1.8 Kelvin set by CM design. Special features ofmore » the refrigerator include the use of warm and cold compression and high efficiency turbo expanders.This paper gives an overview on the wide range of the challenging cooling requirements, the design, fabrication and the commissioning of the installed cryogenic system.« less

Synthetic biology: new engineering rules for an emerging discipline

PubMed Central

Andrianantoandro, Ernesto; Basu, Subhayu; Karig, David K; Weiss, Ron

2006-01-01

Synthetic biologists engineer complex artificial biological systems to investigate natural biological phenomena and for a variety of applications. We outline the basic features of synthetic biology as a new engineering discipline, covering examples from the latest literature and reflecting on the features that make it unique among all other existing engineering fields. We discuss methods for designing and constructing engineered cells with novel functions in a framework of an abstract hierarchy of biological devices, modules, cells, and multicellular systems. The classical engineering strategies of standardization, decoupling, and abstraction will have to be extended to take into account the inherent characteristics of biological devices and modules. To achieve predictability and reliability, strategies for engineering biology must include the notion of cellular context in the functional definition of devices and modules, use rational redesign and directed evolution for system optimization, and focus on accomplishing tasks using cell populations rather than individual cells. The discussion brings to light issues at the heart of designing complex living systems and provides a trajectory for future development. PMID:16738572

Synthetic biology: new engineering rules for an emerging discipline.

PubMed

Andrianantoandro, Ernesto; Basu, Subhayu; Karig, David K; Weiss, Ron

2006-01-01

Synthetic biologists engineer complex artificial biological systems to investigate natural biological phenomena and for a variety of applications. We outline the basic features of synthetic biology as a new engineering discipline, covering examples from the latest literature and reflecting on the features that make it unique among all other existing engineering fields. We discuss methods for designing and constructing engineered cells with novel functions in a framework of an abstract hierarchy of biological devices, modules, cells, and multicellular systems. The classical engineering strategies of standardization, decoupling, and abstraction will have to be extended to take into account the inherent characteristics of biological devices and modules. To achieve predictability and reliability, strategies for engineering biology must include the notion of cellular context in the functional definition of devices and modules, use rational redesign and directed evolution for system optimization, and focus on accomplishing tasks using cell populations rather than individual cells. The discussion brings to light issues at the heart of designing complex living systems and provides a trajectory for future development.

Feature Vector Construction Method for IRIS Recognition

NASA Astrophysics Data System (ADS)

Odinokikh, G.; Fartukov, A.; Korobkin, M.; Yoo, J.

2017-05-01

One of the basic stages of iris recognition pipeline is iris feature vector construction procedure. The procedure represents the extraction of iris texture information relevant to its subsequent comparison. Thorough investigation of feature vectors obtained from iris showed that not all the vector elements are equally relevant. There are two characteristics which determine the vector element utility: fragility and discriminability. Conventional iris feature extraction methods consider the concept of fragility as the feature vector instability without respect to the nature of such instability appearance. This work separates sources of the instability into natural and encodinginduced which helps deeply investigate each source of instability independently. According to the separation concept, a novel approach of iris feature vector construction is proposed. The approach consists of two steps: iris feature extraction using Gabor filtering with optimal parameters and quantization with separated preliminary optimized fragility thresholds. The proposed method has been tested on two different datasets of iris images captured under changing environmental conditions. The testing results show that the proposed method surpasses all the methods considered as a prior art by recognition accuracy on both datasets.

Towards the prediction of essential genes by integration of network topology, cellular localization and biological process information

PubMed Central

2009-01-01

Background The identification of essential genes is important for the understanding of the minimal requirements for cellular life and for practical purposes, such as drug design. However, the experimental techniques for essential genes discovery are labor-intensive and time-consuming. Considering these experimental constraints, a computational approach capable of accurately predicting essential genes would be of great value. We therefore present here a machine learning-based computational approach relying on network topological features, cellular localization and biological process information for prediction of essential genes. Results We constructed a decision tree-based meta-classifier and trained it on datasets with individual and grouped attributes-network topological features, cellular compartments and biological processes-to generate various predictors of essential genes. We showed that the predictors with better performances are those generated by datasets with integrated attributes. Using the predictor with all attributes, i.e., network topological features, cellular compartments and biological processes, we obtained the best predictor of essential genes that was then used to classify yeast genes with unknown essentiality status. Finally, we generated decision trees by training the J48 algorithm on datasets with all network topological features, cellular localization and biological process information to discover cellular rules for essentiality. We found that the number of protein physical interactions, the nuclear localization of proteins and the number of regulating transcription factors are the most important factors determining gene essentiality. Conclusion We were able to demonstrate that network topological features, cellular localization and biological process information are reliable predictors of essential genes. Moreover, by constructing decision trees based on these data, we could discover cellular rules governing essentiality. PMID:19758426

Data approximation using a blending type spline construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dalmo, Rune; Bratlie, Jostein

2014-11-18

Generalized expo-rational B-splines (GERBS) is a blending type spline construction where local functions at each knot are blended together by C{sup k}-smooth basis functions. One way of approximating discrete regular data using GERBS is by partitioning the data set into subsets and fit a local function to each subset. Partitioning and fitting strategies can be devised such that important or interesting data points are interpolated in order to preserve certain features. We present a method for fitting discrete data using a tensor product GERBS construction. The method is based on detection of feature points using differential geometry. Derivatives, which aremore » necessary for feature point detection and used to construct local surface patches, are approximated from the discrete data using finite differences.« less

Recording, Publishing, and Reconstructing Wooden Shipwrecks

NASA Astrophysics Data System (ADS)

Castro, F.; Bendig, C.; Bérubé, M.; Borrero, R.; Budsberg, N.; Dostal, C.; Monteiro, A.; Smith, C.; Torres, R.; Yamafune, K.

2018-04-01

Almost three decades ago J. Richard Steffy (in: Tzalas (ed) Tropis II, proceedings of the 2nd international symposium on ship construction in antiquity. Athens, pp 315-320, 1990, in: Tzalas (ed) Tropis III, proceedings of the 3rd international symposium on ship construction in antiquity. Athens, pp 417-428, 1995) voiced the need to standardize the recording and publication of shipwrecks. Cluster analysis of construction features is difficult if archaeologists record different and non-overlapping features. This paper discusses the necessity to standardize the recording and publishing of a set of consistent and compatible basic construction features when archaeologists assess, survey, or excavate wooden shipwrecks and proposes a methodology for the recording of wooden hulls. It also emphasizes the urgency of a wide and complete sharing of archaeological information in maritime archaeology.

A hardware-algorithm co-design approach to optimize seizure detection algorithms for implantable applications.

PubMed

Raghunathan, Shriram; Gupta, Sumeet K; Markandeya, Himanshu S; Roy, Kaushik; Irazoqui, Pedro P

2010-10-30

Implantable neural prostheses that deliver focal electrical stimulation upon demand are rapidly emerging as an alternate therapy for roughly a third of the epileptic patient population that is medically refractory. Seizure detection algorithms enable feedback mechanisms to provide focally and temporally specific intervention. Real-time feasibility and computational complexity often limit most reported detection algorithms to implementations using computers for bedside monitoring or external devices communicating with the implanted electrodes. A comparison of algorithms based on detection efficacy does not present a complete picture of the feasibility of the algorithm with limited computational power, as is the case with most battery-powered applications. We present a two-dimensional design optimization approach that takes into account both detection efficacy and hardware cost in evaluating algorithms for their feasibility in an implantable application. Detection features are first compared for their ability to detect electrographic seizures from micro-electrode data recorded from kainate-treated rats. Circuit models are then used to estimate the dynamic and leakage power consumption of the compared features. A score is assigned based on detection efficacy and the hardware cost for each of the features, then plotted on a two-dimensional design space. An optimal combination of compared features is used to construct an algorithm that provides maximal detection efficacy per unit hardware cost. The methods presented in this paper would facilitate the development of a common platform to benchmark seizure detection algorithms for comparison and feasibility analysis in the next generation of implantable neuroprosthetic devices to treat epilepsy. Copyright © 2010 Elsevier B.V. All rights reserved.

Inhomogeneity induced and appropriately parameterized semilocal exchange and correlation energy functionals in two-dimensions.

PubMed

Patra, Abhilash; Jana, Subrata; Samal, Prasanjit

2018-04-07

The construction of meta generalized gradient approximations based on the density matrix expansion (DME) is considered as one of the most accurate techniques to design semilocal exchange energy functionals in two-dimensional density functional formalism. The exchange holes modeled using DME possess unique features that make it a superior entity. Parameterized semilocal exchange energy functionals based on the DME are proposed. The use of different forms of the momentum and flexible parameters is to subsume the non-uniform effects of the density in the newly constructed semilocal functionals. In addition to the exchange functionals, a suitable correlation functional is also constructed by working upon the local correlation functional developed for 2D homogeneous electron gas. The non-local effects are induced into the correlation functional by a parametric form of one of the newly constructed exchange energy functionals. The proposed functionals are applied to the parabolic quantum dots with a varying number of confined electrons and the confinement strength. The results obtained with the aforementioned functionals are quite satisfactory, which indicates why these are suitable for two-dimensional quantum systems.

Optimizing the construction of devices to control inaccesible surfaces - case study

NASA Astrophysics Data System (ADS)

Niţu, E. L.; Costea, A.; Iordache, M. D.; Rizea, A. D.; Babă, Al

2017-10-01

The modern concept for the evolution of manufacturing systems requires multi-criteria optimization of technological processes and equipments, prioritizing associated criteria according to their importance. Technological preparation of the manufacturing can be developed, depending on the volume of production, to the limit of favourable economical effects related to the recovery of the costs for the design and execution of the technological equipment. Devices, as subsystems of the technological system, in the general context of modernization and diversification of machines, tools, semi-finished products and drives, are made in a multitude of constructive variants, which in many cases do not allow their identification, study and improvement. This paper presents a case study in which the multi-criteria analysis of some structures, based on a general optimization method, of novelty character, is used in order to determine the optimal construction variant of a control device. The rational construction of the control device confirms that the optimization method and the proposed calculation methods are correct and determine a different system configuration, new features and functions, and a specific method of working to control inaccessible surfaces.

Inhomogeneity induced and appropriately parameterized semilocal exchange and correlation energy functionals in two-dimensions

NASA Astrophysics Data System (ADS)

Patra, Abhilash; Jana, Subrata; Samal, Prasanjit

2018-04-01

The construction of meta generalized gradient approximations based on the density matrix expansion (DME) is considered as one of the most accurate techniques to design semilocal exchange energy functionals in two-dimensional density functional formalism. The exchange holes modeled using DME possess unique features that make it a superior entity. Parameterized semilocal exchange energy functionals based on the DME are proposed. The use of different forms of the momentum and flexible parameters is to subsume the non-uniform effects of the density in the newly constructed semilocal functionals. In addition to the exchange functionals, a suitable correlation functional is also constructed by working upon the local correlation functional developed for 2D homogeneous electron gas. The non-local effects are induced into the correlation functional by a parametric form of one of the newly constructed exchange energy functionals. The proposed functionals are applied to the parabolic quantum dots with a varying number of confined electrons and the confinement strength. The results obtained with the aforementioned functionals are quite satisfactory, which indicates why these are suitable for two-dimensional quantum systems.

Safety in numbers 3: Authenticity, Building knowledge & skills and Competency development & assessment: the ABC of safe medication dosage calculation problem-solving pedagogy.

PubMed

Weeks, Keith W; Meriel Hutton, B; Coben, Diana; Clochesy, John M; Pontin, David

2013-03-01

When designing learning and assessment environments it is essential to articulate the underpinning education philosophy, theory, model and learning style support mechanisms that inform their structure and content. We elaborate on original PhD research that articulates the design rationale of authentic medication dosage calculation problem-solving (MDC-PS) learning and diagnostic assessment environments. These environments embody the principles of authenticity, building knowledge and skills and competency assessment and are designed to support development of competence and bridging of the theory-practice gap. Authentic learning and diagnostic assessment environments capture the features and expert practices that are located in real world practice cultures and recreate them in authentic virtual clinical environments. We explore how this provides students with a safe virtual authentic environment to actively experience, practice and undertake MDC-PS learning and assessment activities. We argue that this is integral to the construction and diagnostic assessment of schemata validity (mental constructions and frameworks that are an individual's internal representation of their world), bridging of the theory-practice gap and cognitive and functional competence development. We illustrate these principles through the underpinning pedagogical design of two online virtual authentic learning and diagnostic assessment environments (safeMedicate and eDose™). Copyright © 2012. Published by Elsevier Ltd.

Design and engineering of photosynthetic light-harvesting and electron transfer using length, time, and energy scales.

PubMed

Noy, Dror; Moser, Christopher C; Dutton, P Leslie

2006-02-01

Decades of research on the physical processes and chemical reaction-pathways in photosynthetic enzymes have resulted in an extensive database of kinetic information. Recently, this database has been augmented by a variety of high and medium resolution crystal structures of key photosynthetic enzymes that now include the two photosystems (PSI and PSII) of oxygenic photosynthetic organisms. Here, we examine the currently available structural and functional information from an engineer's point of view with the long-term goal of reproducing the key features of natural photosystems in de novo designed and custom-built molecular solar energy conversion devices. We find that the basic physics of the transfer processes, namely, the time constraints imposed by the rates of incoming photon flux and the various decay processes allow for a large degree of tolerance in the engineering parameters. Moreover, we find that the requirements to guarantee energy and electron transfer rates that yield high efficiency in natural photosystems are largely met by control of distance between chromophores and redox cofactors. Thus, for projected de novo designed constructions, the control of spatial organization of cofactor molecules within a dense array is initially given priority. Nevertheless, constructions accommodating dense arrays of different cofactors, some well within 1 nm from each other, still presents a significant challenge for protein design.

The Impact of Environmental Design on Doffing Personal Protective Equipment in a Healthcare Environment: A Formative Human Factors Trial.

PubMed

Herlihey, Tracey A; Gelmi, Stefano; Cafazzo, Joseph A; Hall, Trevor N T

2017-06-01

OBJECTIVE To explore the impact of environmental design on doffing personal protective equipment in a simulated healthcare environment. METHODS A mixed-methods approach was used that included human-factors usability testing and qualitative questionnaire responses. A patient room and connecting anteroom were constructed for testing purposes. This experimental doffing area was designed to overcome the environmental failures identified in a previous study and was not constructed based on any generalizable hospital standard. RESULTS In total, 72 healthcare workers from Ontario, Canada, took part in the study and tested the simulated doffing area. The following environmental design changes were tested and were deemed effective: increasing prominence of color-coded zones; securing disinfectant wipes and hand sanitizer; outlining disposal bins locations; providing mirrors to detect possible contamination; providing hand rails to assist with doffing; and restricting the space to doff. Further experimentation and iterative design are required with regard to several important features: positioning the disposal bins for safety, decreasing the risk of contamination and user accessibility; optimal positioning of mirrors for safety; communication within the team; and positioning the secondary team member for optimal awareness. Additional design suggestions also emerged during this study, and they require future investigation. CONCLUSIONS This study highlights the importance of the environment on doffing personal protective equipment in a healthcare setting. Iterative testing and modification of the design of the environment (doffing area) are important to enhancing healthcare worker safety. Infect Control Hosp Epidemiol 2017;38:712-717.

Laser optical appraisal and design of a PRIME/Rover interface

NASA Technical Reports Server (NTRS)

Donaldson, J. A.

1980-01-01

An appraisal of whether to improve the existing multi-laser/multi detector system was undertaken. Two features of the elevation scanning mast which prevent the system from meeting desired specifications were studied. Then elevation scanning mast has 20 detectors, as opposed to the desired 40. This influences the system's overall resolution. The mirror shaft encoder's finite resolution prevents the laser from being aimed exactly as desired. This influences the system's overall accuracy. It was concluded that the existing system needs no modification at present. The design and construction of a data emulator which allowed testing data transactions with a PRIME computer is described, and theory of operation briefly discussed. A full blown PRIME/Rover Interface was designed and built. The capabilities of this Interface and its operating principles are discussed.

Design and characterization of an integrated surface ion trap and micromirror optical cavity.

PubMed

Van Rynbach, Andre; Schwartz, George; Spivey, Robert F; Joseph, James; Vrijsen, Geert; Kim, Jungsang

2017-08-10

We have fabricated and characterized laser-ablated micromirrors on fused silica substrates for constructing stable Fabry-Perot optical cavities. We highlight several design features which allow these cavities to have lengths in the 250-300 μm range and be integrated directly with surface ion traps. We present a method to calculate the optical mode shape and losses of these micromirror cavities as functions of cavity length and mirror shape, and confirm that our simulation model is in good agreement with experimental measurements of the intracavity optical mode at a test wavelength of 780 nm. We have designed and tested a mechanical setup for dampening vibrations and stabilizing the cavity length, and explore applications for these cavities as efficient single-photon sources when combined with trapped Yb171 + ions.

The Physics and Mathematics of MRI

NASA Astrophysics Data System (ADS)

Ansorge, Richard; Graves, Martin

2016-10-01

Magnetic Resonance Imaging is a very important clinical imaging tool. It combines different fields of physics and engineering in a uniquely complex way. MRI is also surprisingly versatile, `pulse sequences' can be designed to yield many different types of contrast. This versatility is unique to MRI. This short book gives both an in depth account of the methods used for the operation and construction of modern MRI systems and also the principles of sequence design and many examples of applications. An important additional feature of this book is the detailed discussion of the mathematical principles used in building optimal MRI systems and for sequence design. The mathematical discussion is very suitable for undergraduates attending medical physics courses. It is also more complete than usually found in alternative books for physical scientists or more clinically orientated works.

Digital microfabrication of user-defined 3D microstructures in cell-laden hydrogels.

PubMed

Soman, Pranav; Chung, Peter H; Zhang, A Ping; Chen, Shaochen

2013-11-01

Complex 3D interfacial arrangements of cells are found in several in vivo biosystems such as blood vasculature, renal glomeruli, and intestinal villi. Current tissue engineering techniques fail to develop suitable 3D microenvironments to evaluate the concurrent effects of complex topography and cell encapsulation. There is a need to develop new fabrication approaches that control cell density and distribution within complex 3D features. In this work, we present a dynamic projection printing process that allows rapid construction of complex 3D structures using custom-defined computer-aided-design (CAD) files. Gelatin-methacrylate (GelMA) constructs featuring user-defined spiral, pyramid, flower, and dome micro-geometries were fabricated with and without encapsulated cells. Encapsulated cells demonstrate good cell viability across all geometries both on the scaffold surface and internal to the structures. Cells respond to geometric cues individually as well as collectively throughout the larger-scale patterns. Time-lapse observations also reveal the dynamic nature of mechanical interactions between cells and micro-geometry. When compared to conventional cell-seeding, cell encapsulation within complex 3D patterned scaffolds provides long-term control over proliferation, cell morphology, and geometric guidance. Overall, this biofabrication technique offers a flexible platform to evaluate cell interactions with complex 3D micro-features, with the ability to scale-up towards high-throughput screening platforms. © 2013 Wiley Periodicals, Inc.

Shaft seals with an easily removable cylinder holder for low-pressure steam turbines

NASA Astrophysics Data System (ADS)

Zakharov, A. E.; Rodionov, D. A.; Pimenov, E. V.; Sobolev, A. S.

2016-01-01

The article is devoted to the problems that occur at the operation of LPC shaft seals (SS) of turbines, particularly, their bearings. The problems arising from the deterioration of oil-protecting rings of SS and bearings and also the consequences in which they can result are considered. The existing SS housing construction types are considered. Their operational features are specified. A new SS construction type with an easily removable holder is presented. The construction of its main elements is described. The sequence of operations of the repair personnel at the restoration of the new SS type spacings is proposed. The comparative analysis of the new and the existing SS construction types is carried out. The assessment results of the efficiency, the operational convenience, and the economic effect after the installation of the new type seals are given. The conclusions about the offered construction prospects are made by results of the comparative analysis and the carried-out assessment. The main advantage of this design is the possibility of spacings restoration both in SS and in oil-protecting rings during a short-term stop of a turbine, even without its cooling. This construction was successfully tested on the working K-300-23.5 LMP turbine. However, its adaptation for other turbines is quite possible.

Community involvement in constructing village health buildings in Uganda and Sierra Leone.

PubMed

Mitchell, M

1995-11-01

Three public health projects in Uganda and Sierra Leone are used to illustrate a new approach to construction of health buildings in villages. Emphasis is placed on community involvement. The health projects were comprehensive and relied on health education, employment of local village health workers, and establishment of village health committees. The objective of community involvement was described as encouragement of people to change their own diets and living conditions. This approach to primary health care is considered to be a strong basis for sustainable social development. Each of the three communities initiated the building projects slightly differently. There was a range of structures: traditional meeting halls, simple rooms with imported materials and a pit latrine, new buildings combining local and imported materials and labor, new nontraditional buildings, rehabilitated existing nontraditional buildings with imported labor and materials, and temporary mobile clinics. Community involvement was at different levels. All three projects were the result of a combined effort of national governments or mission hospitals, nongovernmental organizations, and the host community. The following should be considered before beginning construction: a suitable site, appropriate staff accommodation, the likely motivation of the host community, seasonality, local materials available, availability of skilled labor, and design. A plan of work during construction should include a building design, site supervision, transportation of local and non-local materials, unskilled labor, and skilled labor. Village health committees with or without government help would be responsible for maintenance of buildings after construction. A key feature of this approach is the assessment of the community's ability and capacity to contribute.

The design of the Model V transmission fluorimeter

USGS Publications Warehouse

Fletcher, Mary H.; May, Irving; Anderson, Joseph W.

1950-01-01

The transmission fluorimeter for the measurement of the fluorescence of uranium in fluoride melts is described. The instrument incorporates several improved features which have not been published previously. Unlike the earliest models, the design of the new fluorimeter, with its close machining of parts, reduces the possibility of light leakage and also increases considerably the ease with which the various components of the instrument may be assembled and adjusted. The Model V fluorimeter is a very rugged instrument with a compact arrangement of parts. It possess great flexibility so that various phototubes, measuring devices, light sources, and filter combinations may be used interchangeably. Detailed shop drawings are given for the construction of the fluorimeter.

Modular transportable superconducting magnetic energy systems

NASA Technical Reports Server (NTRS)

Lieurance, Dennis; Kimball, Foster; Rix, Craig

1995-01-01

Design and cost studies were performed for the magnet components of mid-size (1-5 MWh), cold supported SMES systems using alternative configurations. The configurations studied included solenoid magnets, which required onsite assembly of the magnet system, and toroid and racetrack configurations which consisted of factory assembled modules. For each configuration, design concepts and cost information were developed for the major features of the magnet system including the conductor, electrical insulation, and structure. These studies showed that for mid-size systems, the costs of solenoid and toroid magnet configurations are comparable and that the specific configuration to be used for a given application should be based upon customer requirements such as limiting stray fields or minimizing risks in development or construction.

The Stanford MediaServer Project: strategies for building a flexible digital media platform to support biomedical education and research.

PubMed Central

Durack, Jeremy C.; Chao, Chih-Chien; Stevenson, Derek; Andriole, Katherine P.; Dev, Parvati

2002-01-01

Medical media collections are growing at a pace that exceeds the value they currently provide as research and educational resources. To address this issue, the Stanford MediaServer was designed to promote innovative multimedia-based application development. The nucleus of the MediaServer platform is a digital media database strategically designed to meet the information needs of many biomedical disciplines. Key features include an intuitive web-based interface for collaboratively populating the media database, flexible creation of media collections for diverse and specialized purposes, and the ability to construct a variety of end-user applications from the same database to support biomedical education and research. PMID:12463820

The Stanford MediaServer Project: strategies for building a flexible digital media platform to support biomedical education and research.

PubMed

Durack, Jeremy C; Chao, Chih-Chien; Stevenson, Derek; Andriole, Katherine P; Dev, Parvati

2002-01-01

Medical media collections are growing at a pace that exceeds the value they currently provide as research and educational resources. To address this issue, the Stanford MediaServer was designed to promote innovative multimedia-based application development. The nucleus of the MediaServer platform is a digital media database strategically designed to meet the information needs of many biomedical disciplines. Key features include an intuitive web-based interface for collaboratively populating the media database, flexible creation of media collections for diverse and specialized purposes, and the ability to construct a variety of end-user applications from the same database to support biomedical education and research.

Induction simulation of gas core nuclear engine

NASA Technical Reports Server (NTRS)

Poole, J. W.; Vogel, C. E.

1973-01-01

The design, construction and operation of an induction heated plasma device known as a combined principles simulator is discussed. This device incorporates the major design features of the gas core nuclear rocket engine such as solid feed, propellant seeding, propellant injection through the walls, and a transpiration cooled, choked flow nozzle. Both argon and nitrogen were used as propellant simulating material, and sodium was used for fuel simulating material. In addition, a number of experiments were conducted utilizing depleted uranium as the fuel. The test program revealed that satisfactory operation of this device can be accomplished over a range of operating conditions and provided additional data to confirm the validity of the gas core concept.

A magnetically suspended linearly driven cryogenic refrigerator

NASA Technical Reports Server (NTRS)

Stolfi, F.; Goldowsky, M.; Ricciardelli, J.; Shapiro, P.

1983-01-01

This paper described a novel Stirling cycle cryogenic refrigerator which was designed, fabricated and successfully tested at Philips Laboratories. The prominent features of the machine are an electro-magnetic bearing system, a pair of moving magnet linear motors, and clearance seals with a 25 mu m radial gap. The all-metal and ceramic construction eliminates long-term organic contamination of the helium working fluid. The axial positions of the piston and displacer are electronically controlled, permitting independent adjustment of the amplitude of each and their relative phase relationship during operation. A simple passive counterbalance reduces axial vibrations. The design of the refrigerator system components is discussed and a comparison is made between performance estimates and measured results.

Constellation Launch Vehicles Overview

NASA Technical Reports Server (NTRS)

Cook, Steve; Fragola, Joseph R.; Priskos, Alex; Davis, Danny; Kaynard, Mike; Hutt, John; Davis, Stephan; Creech, Steve

2009-01-01

This slide presentation reviews the current status of the launch vehicles associated with the Constellation Program. These are the Ares I and the Ares V. An overview of the Ares launch vehicles is included. The presentation stresses that the major criteria for the Ares I launcher is the safety of the crew, and the presentation reviews the various features that are designed to assure that aim. The Ares I vehicle is being built on a foundation of proven technologies, and the Ares V will give NASA unprecedented performance and payload volume that can enable a range of future missions. The CDs contain videos of scenes from various activities surrounding the design, construction and testing of the vehicles.

A methodology for designing robust multivariable nonlinear control systems. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Grunberg, D. B.

1986-01-01

A new methodology is described for the design of nonlinear dynamic controllers for nonlinear multivariable systems providing guarantees of closed-loop stability, performance, and robustness. The methodology is an extension of the Linear-Quadratic-Gaussian with Loop-Transfer-Recovery (LQG/LTR) methodology for linear systems, thus hinging upon the idea of constructing an approximate inverse operator for the plant. A major feature of the methodology is a unification of both the state-space and input-output formulations. In addition, new results on stability theory, nonlinear state estimation, and optimal nonlinear regulator theory are presented, including the guaranteed global properties of the extended Kalman filter and optimal nonlinear regulators.

Modular transportable superconducting magnetic energy systems

NASA Astrophysics Data System (ADS)

Lieurance, Dennis; Kimball, Foster; Rix, Craig

1995-04-01

Design and cost studies were performed for the magnet components of mid-size (1-5 MWh), cold supported SMES systems using alternative configurations. The configurations studied included solenoid magnets, which required onsite assembly of the magnet system, and toroid and racetrack configurations which consisted of factory assembled modules. For each configuration, design concepts and cost information were developed for the major features of the magnet system including the conductor, electrical insulation, and structure. These studies showed that for mid-size systems, the costs of solenoid and toroid magnet configurations are comparable and that the specific configuration to be used for a given application should be based upon customer requirements such as limiting stray fields or minimizing risks in development or construction.

The Mod-2 wind turbine development project

NASA Technical Reports Server (NTRS)

Linscott, B. S.; Dennett, J. T.; Gordon, L. H.

1981-01-01

A major phase of the Federal Wind Energy Program, the Mod-2 wind turbine, a second-generation machine developed by the Boeing Engineering and Construction Co. for the U.S. Department of Energy and the Lewis Research Center of the National Aeronautics and Space Administration, is described. The Mod-2 is a large (2.5-MW power rating) horizontal-axis wind turbine designed for the generation of electrical power on utility networks. Three machines were built and are located in a cluster at Goodnoe Hills, Washington. All technical aspects of the project are described: design approach, significant innovation features, the mechanical system, the electrical power system, the control system, and the safety system.

KSC-2010-1114

NASA Image and Video Library

2010-01-07

CAPE CANAVERAL, Fla. - The 525-foot-tall Vehicle Assembly Building, in the background, is witness to the formation of the Propellants North Administrative and Maintenance Facility, a new "green" building under construction in Launch Complex 39 at NASA's Kennedy Space Center in Florida. Concrete layers on either side of high-density foam insulation in the facility's walls will prevent any transfer of radiant heat between the exterior and interior of the buildings. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

KSC-2010-1161

NASA Image and Video Library

2010-01-08

CAPE CANAVERAL, Fla. - In Launch Complex 39 at NASA's Kennedy Space Center in Florida, construction of the Propellants North Administrative and Maintenance Facility is moving ahead with the placement of all of the outside walls complete. Concrete layers on either side of high-density foam insulation in the facility's walls will prevent any transfer of radiant heat between the exterior and interior of the buildings. A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cryogenic fuel transfer equipment. The new facility will feature high-efficiency roofs and walls, “Cool Dry Quiet” air conditioning with energy recovery technology, efficient lighting, and other sustainable features. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design, or LEED, Platinum certification. If successful, Propellants North will be the first Kennedy facility to achieve this highest of LEED ratings after it is completed in the summer of 2010. The facility was designed for NASA by Jones Edmunds and Associates. Photo credit: NASA/Jim Grossmann

A description of discrete internal representation schemes for visual pattern discrimination.

PubMed

Foster, D H

1980-01-01

A general description of a class of schemes for pattern vision is outlined in which the visual system is assumed to form a discrete internal representation of the stimulus. These representations are discrete in that they are considered to comprise finite combinations of "components" which are selected from a fixed and finite repertoire, and which designate certain simple pattern properties or features. In the proposed description it is supposed that the construction of an internal representation is a probabilistic process. A relationship is then formulated associating the probability density functions governing this construction and performance in visually discriminating patterns when differences in pattern shape are small. Some questions related to the application of this relationship to the experimental investigation of discrete internal representations are briefly discussed.

The HDF Product Designer - Interoperability in the First Mile

NASA Astrophysics Data System (ADS)

Lee, H.; Jelenak, A.; Habermann, T.

2014-12-01

Interoperable data have been a long-time goal in many scientific communities. The recent growth in analysis, visualization and mash-up applications that expect data stored in a standardized manner has brought the interoperability issue to the fore. On the other hand, producing interoperable data is often regarded as a sideline task in a typical research team for which resources are not readily available. The HDF Group is developing a software tool aimed at lessening the burden of creating data in standards-compliant, interoperable HDF5 files. The tool, named HDF Product Designer, lowers the threshold needed to design such files by providing a user interface that combines the rich HDF5 feature set with applicable metadata conventions. Users can quickly devise new HDF5 files while at the same time seamlessly incorporating the latest best practices and conventions from their community. That is what the term interoperability in the first mile means: enabling generation of interoperable data in HDF5 files from the onset of their production. The tool also incorporates collaborative features, allowing team approach in the file design, as well as easy transfer of best practices as they are being developed. The current state of the tool and the plans for future development will be presented. Constructive input from interested parties is always welcome.

A comparative study of family-specific protein-ligand complex affinity prediction based on random forest approach

NASA Astrophysics Data System (ADS)

Wang, Yu; Guo, Yanzhi; Kuang, Qifan; Pu, Xuemei; Ji, Yue; Zhang, Zhihang; Li, Menglong

2015-04-01

The assessment of binding affinity between ligands and the target proteins plays an essential role in drug discovery and design process. As an alternative to widely used scoring approaches, machine learning methods have also been proposed for fast prediction of the binding affinity with promising results, but most of them were developed as all-purpose models despite of the specific functions of different protein families, since proteins from different function families always have different structures and physicochemical features. In this study, we proposed a random forest method to predict the protein-ligand binding affinity based on a comprehensive feature set covering protein sequence, binding pocket, ligand structure and intermolecular interaction. Feature processing and compression was respectively implemented for different protein family datasets, which indicates that different features contribute to different models, so individual representation for each protein family is necessary. Three family-specific models were constructed for three important protein target families of HIV-1 protease, trypsin and carbonic anhydrase respectively. As a comparison, two generic models including diverse protein families were also built. The evaluation results show that models on family-specific datasets have the superior performance to those on the generic datasets and the Pearson and Spearman correlation coefficients ( R p and Rs) on the test sets are 0.740, 0.874, 0.735 and 0.697, 0.853, 0.723 for HIV-1 protease, trypsin and carbonic anhydrase respectively. Comparisons with the other methods further demonstrate that individual representation and model construction for each protein family is a more reasonable way in predicting the affinity of one particular protein family.

Evaluation of energy efficient design competition of a public office building in North Greece

NASA Astrophysics Data System (ADS)

Chatzimanoli, Asimina

Over the past few years in Greece there have been changes in the National Environmental and Energy Policy related to sustainability and energy conservation-saving, concerning the built environment as well. In this context, in 1999, the Hellenic Public Real Estate Corporation announced a Public Open Competition for the "Design and Construction" of a Police Station in the city of Kilkis, in North Greece. The energy efficiency and bioclimatic design was part of the General Design Principles of the brief. The following Report aims at evaluating the energy performance of the building and the comfort levels in the internal environment and determining the benefits of incorporating environmental design in a Public Office Building, in terms of savings in the energy consumption for heating. The Methodology included a description of the features of the design, analysis of the differences between the initial design and the constructed building, investigation of the operation of the constructed building (monitoring, questionnaire survey, energy consumption) and evaluation of the effect of the differences mentioned, using computer simulation (TAS software). Internal Temperatures fluctuated less than the external but for most of the monitoring period (end of mid-season-beginning of summer) Maximum Temperatures were higher than the external. The occupants gave positive comments and evaluated the general working conditions in the building as good, but the majority were not aware of the Passive Solar Systems installed in the building. The actual energy consumption for heating (150.85kWh/m2) is approximately 85% of the average consumption of Public Office Buildings in North Greece but 50% higher than that of recently built Public Office Buildings. However, the figure from the simulation analysis (corresponding to Office and Common spaces) is approximately 1/3 of the actual (55.14 kWh/m2), suggesting that proper operation of the building could result in significant reduction in energy required for heating.

Conceptions of Height and Verticality in the History of Skyscrapers and Skylines

NASA Astrophysics Data System (ADS)

Maslovskaya, Oksana; Ignatov, Grigoriy

2018-03-01

The main goal of this article is to reveal the significance of height and verticality history of skyscrapers and skylines. The objectives are as follows: 1. trace the origin of design concepts related to skyscraper; 2. discuss the perceived experience of the cultural aspects of skyscrapers and skylines; 3. describe the differences and similarities of the profiles of with comparable skylines. The methodology of study is designed to explore the perceived theory and principals of skyscraper and skyline development phenomenon and its key features. The skyscraper reveals an assertive creative form of vertical design. Skyscraper construction also relates to the origin of ancient cultural symbolism as the dominant vertical element as the main features of an ordered space. The historical idea of height reaches back to the earliest civilization such as the Tower of Babel. Philosophical approaches of elements of such post-structuralism have been included in studying of skyscraper phenomenon. The analysis of skyscraper and their resulting skyline are examined to show the connection to their origins with their concepts of height and verticality. From the historical perspective, cities with skyscrapers and a skyline turn out to be an assertive manifestation of common ideas of height and verticality.

Intelligence and Creativity in Problem Solving: The Importance of Test Features in Cognition Research

PubMed Central

Jaarsveld, Saskia; Lachmann, Thomas

2017-01-01

This paper discusses the importance of three features of psychometric tests for cognition research: construct definition, problem space, and knowledge domain. Definition of constructs, e.g., intelligence or creativity, forms the theoretical basis for test construction. Problem space, being well or ill-defined, is determined by the cognitive abilities considered to belong to the constructs, e.g., convergent thinking to intelligence, divergent thinking to creativity. Knowledge domain and the possibilities it offers cognition are reflected in test results. We argue that (a) comparing results of tests with different problem spaces is more informative when cognition operates in both tests on an identical knowledge domain, and (b) intertwining of abilities related to both constructs can only be expected in tests developed to instigate such a process. Test features should guarantee that abilities can contribute to self-generated and goal-directed processes bringing forth solutions that are both new and applicable. We propose and discuss a test example that was developed to address these issues. PMID:28220098

Specificity of high-rise construction and real estate markets in the regional economy: an analysis of Russian practice (example of St. Petersburg)

NASA Astrophysics Data System (ADS)

Vilken, Viktoriya; Kalinina, Olga; Dubgorn, Alissa

2018-03-01

In paper features of the regional markets of construction the commercial and residential real estate on the example of St. Petersburg are defined. The current situation is analysed, the specific features of branch are revealed. The major factors influencing investors making decisions on construction of various types of objects are defined. The main methods of advance of real estate objects are considered.

Average combination difference morphological filters for fault feature extraction of bearing

NASA Astrophysics Data System (ADS)

Lv, Jingxiang; Yu, Jianbo

2018-02-01

In order to extract impulse components from vibration signals with much noise and harmonics, a new morphological filter called average combination difference morphological filter (ACDIF) is proposed in this paper. ACDIF constructs firstly several new combination difference (CDIF) operators, and then integrates the best two CDIFs as the final morphological filter. This design scheme enables ACIDF to extract positive and negative impacts existing in vibration signals to enhance accuracy of bearing fault diagnosis. The length of structure element (SE) that affects the performance of ACDIF is determined adaptively by a new indicator called Teager energy kurtosis (TEK). TEK further improves the effectiveness of ACDIF for fault feature extraction. Experimental results on the simulation and bearing vibration signals demonstrate that ACDIF can effectively suppress noise and extract periodic impulses from bearing vibration signals.

Self-Organizing Map With Time-Varying Structure to Plan and Control Artificial Locomotion.

PubMed

Araujo, Aluizio F R; Santana, Orivaldo V

2015-08-01

This paper presents an algorithm, self-organizing map-state trajectory generator (SOM-STG), to plan and control legged robot locomotion. The SOM-STG is based on an SOM with a time-varying structure characterized by constructing autonomously close-state trajectories from an arbitrary number of robot postures. Each trajectory represents a cyclical movement of the limbs of an animal. The SOM-STG was designed to possess important features of a central pattern generator, such as rhythmic pattern generation, synchronization between limbs, and swapping between gaits following a single command. The acquisition of data for SOM-STG is based on learning by demonstration in which the data are obtained from different demonstrator agents. The SOM-STG can construct one or more gaits for a simulated robot with six legs, can control the robot with any of the gaits learned, and can smoothly swap gaits. In addition, SOM-STG can learn to construct a state trajectory form observing an animal in locomotion. In this paper, a dog is the demonstrator agent.

Automated building of organometallic complexes from 3D fragments.

PubMed

Foscato, Marco; Venkatraman, Vishwesh; Occhipinti, Giovanni; Alsberg, Bjørn K; Jensen, Vidar R

2014-07-28

A method for the automated construction of three-dimensional (3D) molecular models of organometallic species in design studies is described. Molecular structure fragments derived from crystallographic structures and accurate molecular-level calculations are used as 3D building blocks in the construction of multiple molecular models of analogous compounds. The method allows for precise control of stereochemistry and geometrical features that may otherwise be very challenging, or even impossible, to achieve with commonly available generators of 3D chemical structures. The new method was tested in the construction of three sets of active or metastable organometallic species of catalytic reactions in the homogeneous phase. The performance of the method was compared with those of commonly available methods for automated generation of 3D models, demonstrating higher accuracy of the prepared 3D models in general, and, in particular, a much wider range with respect to the kind of chemical structures that can be built automatically, with capabilities far beyond standard organic and main-group chemistry.

A Concept for a Mobile Remote Manipulator System

NASA Technical Reports Server (NTRS)

Mikulus, M. M., Jr.; Bush, H. G.; Wallsom, R. E.; Jensen, J. K.

1985-01-01

A conceptual design for a Mobile Remote Manipulator System (MRMS) is presented. This concept does not require continuous rails for mobility (only guide pins at truss hardpoints) and is very compact, being only one bay square. The MRMS proposed is highly maneuverable and is able to move in any direction along the orthogonal guide pin array under complete control at all times. The proposed concept would greatly enhance the safety and operational capabilities of astronauts performing EVA functions such as structural assembly, payload transport and attachment, space station maintenance, repair or modification, and future spacecraft construction or servicing. The MRMS drive system conceptual design presented is a reasonably simple mechanical device which can be designed to exhibit high reliability. Developmentally, all components of the proposed MRMS either exist or are considered to be completely state of the art designs requiring minimal development, features which should enhance reliability and minimize costs.

Design of high strength polymer metal interfaces by laser microstructured surfaces

NASA Astrophysics Data System (ADS)

Steinert, P.; Dittes, A.; Schimmelpfennig, R.; Scharf, I.; Lampke, T.; Schubert, A.

2018-06-01

In the areas of automotive, aeronautics and civil structures, lightweight construction is a current and a future need. Thus, multi material design has rapidly grown in importance, especially hybrid materials based on fiber reinforced plastics and aluminum offer great potential. Therefore, mechanical interlocking is a convenient way of designing the interface. Laser structuring is already used to generate a variety of surface topographies leading to high bond strengths. This paper investigates different laser structures aiming on highest joint strengths for aluminum and glass fiber reinforced polyamide 6 interfaces. Self-organizing pin structures comprised by additional micro/nano features as well as drilled hole structures, both ranging on the micrometer range, are compared to corundum blasting as a standard method for surface conditioning. For the presented surface structures, thermal joining and ultrasonic assisted joining are regarded towards their potential for an optimum joint design.

Design and development of an F/A-18 inlet distortion rake: A cost and time saving solution

NASA Technical Reports Server (NTRS)

Yuhas, Andrew J.; Ray, Ronald J.; Burley, Richard R.; Steenken, William G.; Lechtenberg, Leon; Thornton, Don

1995-01-01

An innovative inlet total pressure distortion measurement rake has been designed and developed for the F/A-18 A/B/C/D aircraft inlet. The design was conceived by NASA and General Electric Aircraft Engines personnel. This rake has been flight qualified and flown in the F/A-18 High Alpha Research Vehicle at NASA Dryden Flight Research Center, Edwards, California. The eight-legged, one-piece, wagon wheel design of the rake was developed at a reduced cost and offered reduced installation time compared to traditional designs. The rake features 40 dual-measurement ports for low- and high-frequency pressure measurements with the high-frequency transducer mounted at the port. This high-frequency transducer offers direct absolute pressure measurements from low to high frequencies of interest, thereby allowing the rake to be used during highly dynamic aircraft maneuvers. Outstanding structural characteristics are inherent to the design through its construction and use of lightweight materials.

Development of novel recombinant biomimetic chimeric MPG-based peptide as nanocarriers for gene delivery: Imitation of a real cargo.

PubMed

Majidi, Asia; Nikkhah, Maryam; Sadeghian, Faranak; Hosseinkhani, Saman

2016-10-01

In last decades great efforts have been devoted to the study of development of recombinant peptide based vectors that consist of biological motifs with potential applications in gene therapy. Recombinant Biomimetic Chimeric Vectors (rBCVs) are biopolymeric nanocarriers that are designed to mimic viral features to overcome the cellular obstacles in gene transferring pathway into cell nucleus. In this research, we designed and genetically engineered three novel rBCVs with similar sequences that differed in motifs arrangement and motif abundance: MPG-2H1, 2TMPG-2H1 and 2RMPG-2H1. The MPG as a famous amphipathic cell penetrating peptide is the main segment of these constructs which was studied for the first time in association with truncated histone H1 DNA condensing motif. Through the performance of several physicochemical and biological assays, the rBCVs were remarkably examined regarding transfection efficiency. The main objective of this study is focused on the importance of motif design in transfection efficiency of rBCVs on one hand, and the assessment of correlation between structural features and functionality of motifs on the other hand. The results revealed that all three kinds of rBCVs/pDNA nanoparticles with average sizes of 200nm could overwhelm the cellular obstacles associated with gene transfer, and lead to efficient gene delivery. Furthermore, no significant toxicity was perceived and efficient endosome disruptive activity was obtained. It is noteworthy to say among three mentioned constructs 2RMPG-2H1 showed the highest transfection efficiency. Overall the peptide based vectors hold great promise as a nontoxic and effective gene carrier in vitro and in vivo, besides the rational design possibility as the most vital advantages over the other non-viral gene delivery vectors. Copyright © 2016 Elsevier B.V. All rights reserved.

Taking Advantage of Automated Assessment of Student-Constructed Graphs in Science

ERIC Educational Resources Information Center

Vitale, Jonathan M.; Lai, Kevin; Linn, Marcia C.

2015-01-01

We present a new system for automated scoring of graph construction items that address complex science concepts, feature qualitative prompts, and support a range of possible solutions. This system utilizes analysis of spatial features (e.g., slope of a line) to evaluate potential student ideas represented within graphs. Student ideas are then…

A Versatile Lifting Device for Lunar Surface Payload Handling, Inspection and Regolith Transport Operations

NASA Technical Reports Server (NTRS)

Doggett, William R.; Dorsey, John T.; Collins, Timothy J.; King, Bruce D.; Mikulas, Martin M., Jr.

2008-01-01

Devices for lifting and transporting payloads and material are critical for efficient Earth-based construction operations. Devices with similar functionality will be needed to support lunar-outpost construction, servicing, inspection, regolith excavation, grading and payload placement. Past studies have proposed that only a few carefully selected devices are required for a lunar outpost. One particular set of operations involves lifting and manipulating payloads in the 100 kg to 3,000 kg range, which are too large or massive to be handled by unassisted astronauts. This paper will review historical devices used for payload handling in space and on earth to derive a set of desirable features for a device that can be used on planetary surfaces. Next, an innovative concept for a lifting device is introduced, which includes many of the desirable features. The versatility of the device is discussed, including its application to lander unloading, servicing, inspection, regolith excavation and site preparation. Approximate rules, which can be used to size the device for specific payload mass and reach requirements, are provided. Finally, details of a test-bed implementation of the innovative concept, which will be used to validate the structural design and develop operational procedures, is provided.

Constructing an Efficient Self-Tuning Aircraft Engine Model for Control and Health Management Applications

NASA Technical Reports Server (NTRS)

Armstrong, Jeffrey B.; Simon, Donald L.

2012-01-01

Self-tuning aircraft engine models can be applied for control and health management applications. The self-tuning feature of these models minimizes the mismatch between any given engine and the underlying engineering model describing an engine family. This paper provides details of the construction of a self-tuning engine model centered on a piecewise linear Kalman filter design. Starting from a nonlinear transient aerothermal model, a piecewise linear representation is first extracted. The linearization procedure creates a database of trim vectors and state-space matrices that are subsequently scheduled for interpolation based on engine operating point. A series of steady-state Kalman gains can next be constructed from a reduced-order form of the piecewise linear model. Reduction of the piecewise linear model to an observable dimension with respect to available sensed engine measurements can be achieved using either a subset or an optimal linear combination of "health" parameters, which describe engine performance. The resulting piecewise linear Kalman filter is then implemented for faster-than-real-time processing of sensed engine measurements, generating outputs appropriate for trending engine performance, estimating both measured and unmeasured parameters for control purposes, and performing on-board gas-path fault diagnostics. Computational efficiency is achieved by designing multidimensional interpolation algorithms that exploit the shared scheduling of multiple trim vectors and system matrices. An example application illustrates the accuracy of a self-tuning piecewise linear Kalman filter model when applied to a nonlinear turbofan engine simulation. Additional discussions focus on the issue of transient response accuracy and the advantages of a piecewise linear Kalman filter in the context of validation and verification. The techniques described provide a framework for constructing efficient self-tuning aircraft engine models from complex nonlinear simulations.Self-tuning aircraft engine models can be applied for control and health management applications. The self-tuning feature of these models minimizes the mismatch between any given engine and the underlying engineering model describing an engine family. This paper provides details of the construction of a self-tuning engine model centered on a piecewise linear Kalman filter design. Starting from a nonlinear transient aerothermal model, a piecewise linear representation is first extracted. The linearization procedure creates a database of trim vectors and state-space matrices that are subsequently scheduled for interpolation based on engine operating point. A series of steady-state Kalman gains can next be constructed from a reduced-order form of the piecewise linear model. Reduction of the piecewise linear model to an observable dimension with respect to available sensed engine measurements can be achieved using either a subset or an optimal linear combination of "health" parameters, which describe engine performance. The resulting piecewise linear Kalman filter is then implemented for faster-than-real-time processing of sensed engine measurements, generating outputs appropriate for trending engine performance, estimating both measured and unmeasured parameters for control purposes, and performing on-board gas-path fault diagnostics. Computational efficiency is achieved by designing multidimensional interpolation algorithms that exploit the shared scheduling of multiple trim vectors and system matrices. An example application illustrates the accuracy of a self-tuning piecewise linear Kalman filter model when applied to a nonlinear turbofan engine simulation. Additional discussions focus on the issue of transient response accuracy and the advantages of a piecewise linear Kalman filter in the context of validation and verification. The techniques described provide a framework for constructing efficient self-tuning aircraft engine models from complex nonlinear simulatns.

A Feature and Algorithm Selection Method for Improving the Prediction of Protein Structural Class.

PubMed

Ni, Qianwu; Chen, Lei

2017-01-01

Correct prediction of protein structural class is beneficial to investigation on protein functions, regulations and interactions. In recent years, several computational methods have been proposed in this regard. However, based on various features, it is still a great challenge to select proper classification algorithm and extract essential features to participate in classification. In this study, a feature and algorithm selection method was presented for improving the accuracy of protein structural class prediction. The amino acid compositions and physiochemical features were adopted to represent features and thirty-eight machine learning algorithms collected in Weka were employed. All features were first analyzed by a feature selection method, minimum redundancy maximum relevance (mRMR), producing a feature list. Then, several feature sets were constructed by adding features in the list one by one. For each feature set, thirtyeight algorithms were executed on a dataset, in which proteins were represented by features in the set. The predicted classes yielded by these algorithms and true class of each protein were collected to construct a dataset, which were analyzed by mRMR method, yielding an algorithm list. From the algorithm list, the algorithm was taken one by one to build an ensemble prediction model. Finally, we selected the ensemble prediction model with the best performance as the optimal ensemble prediction model. Experimental results indicate that the constructed model is much superior to models using single algorithm and other models that only adopt feature selection procedure or algorithm selection procedure. The feature selection procedure or algorithm selection procedure are really helpful for building an ensemble prediction model that can yield a better performance. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Design of an unmanned, reusable vehicle to de-orbit debris in Earth orbit

NASA Technical Reports Server (NTRS)

Aziz, Shahed; Cunningham, Timothy W.; Moore-Mccassey, Michelle

1990-01-01

The space debris problem is becoming more important because as orbital missions increase, the amount of debris increases. It was the design team's objective to present alternative designs and a problem solution for a deorbiting vehicle that will alleviate the problem by reducing the amount of large debris in earth orbit. The design team was asked to design a reusable, unmanned vehicle to de-orbit debris in earth orbit. The design team will also construct a model to demonstrate the system configuration and key operating features. The alternative designs for the unmanned, reusable vehicle were developed in three stages: selection of project requirements and success criteria, formulation of a specification list, and the creation of alternatives that would satisfy the standards set forth by the design team and their sponsor. The design team selected a Chain and Bar Shot method for deorbiting debris in earth orbit. The De-orbiting Vehicle (DOV) uses the NASA Orbital Maneuvering Vehicle (OMV) as the propulsion and command modules with the deorbiting module attached to the front.

The Wavelet Element Method. Part 2; Realization and Additional Features in 2D and 3D

NASA Technical Reports Server (NTRS)

Canuto, Claudio; Tabacco, Anita; Urban, Karsten

1998-01-01

The Wavelet Element Method (WEM) provides a construction of multiresolution systems and biorthogonal wavelets on fairly general domains. These are split into subdomains that are mapped to a single reference hypercube. Tensor products of scaling functions and wavelets defined on the unit interval are used on the reference domain. By introducing appropriate matching conditions across the interelement boundaries, a globally continuous biorthogonal wavelet basis on the general domain is obtained. This construction does not uniquely define the basis functions but rather leaves some freedom for fulfilling additional features. In this paper we detail the general construction principle of the WEM to the 1D, 2D and 3D cases. We address additional features such as symmetry, vanishing moments and minimal support of the wavelet functions in each particular dimension. The construction is illustrated by using biorthogonal spline wavelets on the interval.

Participatory Design of an Integrated Information System Design to Support Public Health Nurses and Nurse Managers

PubMed Central

Reeder, Blaine; Hills, Rebecca A.; Turner, Anne M.; Demiris, George

2014-01-01

Objectives The objectives of the study were to use persona-driven and scenario-based design methods to create a conceptual information system design to support public health nursing. Design and Sample We enrolled 19 participants from two local health departments to conduct an information needs assessment, create a conceptual design, and conduct a preliminary design validation. Measures Interviews and thematic analysis were used to characterize information needs and solicit design recommendations from participants. Personas were constructed from participant background information, and scenario-based design was used to create a conceptual information system design. Two focus groups were conducted as a first iteration validation of information needs, personas, and scenarios. Results Eighty-nine information needs were identified. Two personas and 89 scenarios were created. Public health nurses and nurse managers confirmed the accuracy of information needs, personas, scenarios, and the perceived usefulness of proposed features of the conceptual design. Design artifacts were modified based on focus group results. Conclusion Persona-driven design and scenario-based design are feasible methods to design for common work activities in different local health departments. Public health nurses and nurse managers should be engaged in the design of systems that support their work. PMID:24117760

AlphaSpace: Fragment-Centric Topographical Mapping To Target Protein–Protein Interaction Interfaces

PubMed Central

2016-01-01

Inhibition of protein–protein interactions (PPIs) is emerging as a promising therapeutic strategy despite the difficulty in targeting such interfaces with drug-like small molecules. PPIs generally feature large and flat binding surfaces as compared to typical drug targets. These features pose a challenge for structural characterization of the surface using geometry-based pocket-detection methods. An attractive mapping strategy—that builds on the principles of fragment-based drug discovery (FBDD)—is to detect the fragment-centric modularity at the protein surface and then characterize the large PPI interface as a set of localized, fragment-targetable interaction regions. Here, we introduce AlphaSpace, a computational analysis tool designed for fragment-centric topographical mapping (FCTM) of PPI interfaces. Our approach uses the alpha sphere construct, a geometric feature of a protein’s Voronoi diagram, to map out concave interaction space at the protein surface. We introduce two new features—alpha-atom and alpha-space—and the concept of the alpha-atom/alpha-space pair to rank pockets for fragment-targetability and to facilitate the evaluation of pocket/fragment complementarity. The resulting high-resolution interfacial map of targetable pocket space can be used to guide the rational design and optimization of small molecule or biomimetic PPI inhibitors. PMID:26225450

Aggregation of p-Sulfonatocalixarene-Based Amphiphiles and Supra-Amphiphiles

PubMed Central

Basilio, Nuno; Francisco, Vitor; Garcia-Rio, Luis

2013-01-01

p-Sulfonatocalixarenes are a special class of water soluble macrocyclic molecules made of 4-hydroxybenzenesulfonate units linked by methylene bridges. One of the main features of these compounds relies on their ability to form inclusion complexes with cationic and neutral species. This feature, together with their water solubility and apparent biological compatibility, had enabled them to emerge as one the most important host receptors in supramolecular chemistry. Attachment of hydrophobic alkyl chains to these compounds leads to the formation of macrocyclic host molecules with amphiphilic properties. Like other oligomeric surfactants, these compounds present improved performance with respect to their monomeric counterparts. In addition, they hold their recognition abilities and present several structural features that depend on the size of the macrocycle and on the length of the alkyl chain, such as preorganization, flexibility and adopted conformations, which make these molecules very interesting to study structure-aggregation relationships. Moreover, the recognition abilities of p-sulfonatocalixarenes enable them to be applied in the design of amphiphiles constructed from non-covalent, rather than covalent, bonds (supramolecular amphiphiles). In this review, we summarize the developments made on the design and synthesis of p-sulfonatocalixarenes-based surfactants, the characterization of their self-assembly properties and on how their structure affects these properties. PMID:23380960

AP1000{sup R} nuclear power plant safety overview for spent fuel cooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorgemans, J.; Mulhollem, L.; Glavin, J.

2012-07-01

The AP1000{sup R} plant is an 1100-MWe class pressurized water reactor with passive safety features and extensive plant simplifications that enhance construction, operation, maintenance, safety and costs. The AP1000 design uses passive features to mitigate design basis accidents. The passive safety systems are designed to function without safety-grade support systems such as AC power, component cooling water, service water or HVAC. Furthermore, these passive features 'fail safe' during a non-LOCA event such that DC power and instrumentation are not required. The AP1000 also has simple, active, defense-in-depth systems to support normal plant operations. These active systems provide the first levelmore » of defense against more probable events and they provide investment protection, reduce the demands on the passive features and support the probabilistic risk assessment. The AP1000 passive safety approach allows the plant to achieve and maintain safe shutdown in case of an accident for 72 hours without operator action, meeting the expectations provided in the U.S. Utility Requirement Document and the European Utility Requirements for passive plants. Limited operator actions are required to maintain safe conditions in the spent fuel pool via passive means. In line with the AP1000 approach to safety described above, the AP1000 plant design features multiple, diverse lines of defense to ensure spent fuel cooling can be maintained for design-basis events and beyond design-basis accidents. During normal and abnormal conditions, defense-in-depth and other systems provide highly reliable spent fuel pool cooling. They rely on off-site AC power or the on-site standby diesel generators. For unlikely design basis events with an extended loss of AC power (i.e., station blackout) or loss of heat sink or both, spent fuel cooling can still be provided indefinitely: - Passive systems, requiring minimal or no operator actions, are sufficient for at least 72 hours under all possible pool heat load conditions. - After 3 days, several different means are provided to continue spent fuel cooling using installed plant equipment as well as off-site equipment with built-in connections. Even for beyond design basis accidents with postulated pool damage and multiple failures in the passive safety-related systems and in the defense-in-depth active systems, the AP1000 multiple spent fuel pool spray and fill systems provide additional lines of defense to prevent spent fuel damage. (authors)« less

"Globalized public health." A transdisciplinary comprehensive framework for analyzing contemporary globalization's influences on the field of public health.

PubMed

Lapaige, Véronique

2009-01-01

The current phase of globalization represents a "double-edged sword" challenge facing public health practitioners and health policy makers. The first "edge" throws light on two constructs in the field of public health: global health (formerly international health) and globalized public health. The second "edge" is that of global governance, and raises the question, "how can we construct public health regulations that adequately respond to both global and local complexities related to the two constructs mentioned earlier (global health and globalized public health)?" The two constructs call for the development of norms that will assure sustained population-wide health improvement and these two constructs have their own conceptual tools and theoretical models that permit a better understanding of them. In this paper, we introduce the "globalized public health" construct and we present an interactive comprehensive framework for critically analyzing contemporary globalization's influences on the field of public health. "Globalized public health", simultaneously a theoretical model and a conceptual framework, concerns the transformation of the field of public health in the sociohistorical context of globalization. The model is the fruit of an original theoretical research study conducted from 2005 to 2008 ("contextualized research," Gibbons' Mode II of knowledge production), founded on a QUAL-quant sequential mixed-method design. This research also reflects our political and ideological position, fuelled with aspirations of social democracy and cosmopolitical values. It is profoundly anchored in the pragmatic approach to globalization, looking to "reconcile" the market and equity. The model offers several features to users: (1) it is transdisciplinary; (2) it is interactive (CD-ROM); (3) it is nonlinear (nonlinear interrelations between the contextual globalization and the field of public health); (4) it is synchronic/diachronic (a double-crossed perspective permits analysis of global social change, the emergence of global agency and the transmutation of the field of public health, in the full complexity of their nonlinear interaction); (5) it offers five characteristics as an auto-eco-organized system of social interactions, or dynamic, nonlinear sociohistorical system. The model features a visual interface (five interrelated figures), a structure of 30 "integrator concepts" that integrates 114 other element-parts via 1,300 hypertext links. The model is both a knowledge translation tool and an interactive heuristic guide designed for practitioners and researchers in public health/community health/population health, as well as for decision-makers at all levels.

“Globalized public health.” A transdisciplinary comprehensive framework for analyzing contemporary globalization’s influences on the field of public health

PubMed Central

Lapaige, Véronique

2009-01-01

The current phase of globalization represents a “double-edged sword” challenge facing public health practitioners and health policy makers. The first “edge” throws light on two constructs in the field of public health: global health (formerly international health) and globalized public health. The second “edge” is that of global governance, and raises the question, “how can we construct public health regulations that adequately respond to both global and local complexities related to the two constructs mentioned earlier (global health and globalized public health)?” The two constructs call for the development of norms that will assure sustained population-wide health improvement and these two constructs have their own conceptual tools and theoretical models that permit a better understanding of them. In this paper, we introduce the “globalized public health” construct and we present an interactive comprehensive framework for critically analyzing contemporary globalization’s influences on the field of public health. “Globalized public health”, simultaneously a theoretical model and a conceptual framework, concerns the transformation of the field of public health in the sociohistorical context of globalization. The model is the fruit of an original theoretical research study conducted from 2005 to 2008 (“contextualized research,” Gibbons’ Mode II of knowledge production), founded on a QUAL-quant sequential mixed-method design. This research also reflects our political and ideological position, fuelled with aspirations of social democracy and cosmopolitical values. It is profoundly anchored in the pragmatic approach to globalization, looking to “reconcile” the market and equity. The model offers several features to users: (1) it is transdisciplinary; (2) it is interactive (CD-ROM); (3) it is nonlinear (nonlinear interrelations between the contextual globalization and the field of public health); (4) it is synchronic/diachronic (a double-crossed perspective permits analysis of global social change, the emergence of global agency and the transmutation of the field of public health, in the full complexity of their nonlinear interaction); (5) it offers five characteristics as an auto-eco-organized system of social interactions, or dynamic, nonlinear sociohistorical system. The model features a visual interface (five interrelated figures), a structure of 30 “integrator concepts” that integrates 114 other element-parts via 1,300 hypertext links. The model is both a knowledge translation tool and an interactive heuristic guide designed for practitioners and researchers in public health/community health/population health, as well as for decision-makers at all levels. PMID:22312210