Aerodynamic Performance of Hand Launch Glider

NASA Astrophysics Data System (ADS)

Koike, Masaru; Ishii, Mitsuru

In recent years Micro Air Vehicles (MAV) for disaster aerial video are developed vigorously. In order to improve aerodynamic performance of MAV wing performance in low Reynolds numbers (Re) need to be improved, but research on the theme are very rare. In category of Hand Launch Glider, a kind of model aircraft, glide performance are competed, as a result high performance airfoils in Re is around 20,000 are developed. Therefore for MAV's aerodynamic performance improvement airfoils of Hand Launch Gliders should be referred and aerodynamic characteristics of the airfoils desired to be studied. So in this research, aerodynamic characteristics of the gliders are measured in wind tunnel. And also consistency between wind tunnel test and glide test in calm air is examined to confirm reliability of wind tunnel test. Comparison of different airfoils and flow visualization are also performed.

Digital simulation of hybrid loop operation in RFI backgrounds.

NASA Technical Reports Server (NTRS)

Ziemer, R. E.; Nelson, D. R.

1972-01-01

A digital computer model for Monte-Carlo simulation of an imperfect second-order hybrid phase-locked loop (PLL) operating in radio-frequency interference (RFI) and Gaussian noise backgrounds has been developed. Characterization of hybrid loop performance in terms of cycle slipping statistics and phase error variance, through computer simulation, indicates that the hybrid loop has desirable performance characteristics in RFI backgrounds over the conventional PLL or the costas loop.

The Effect of Increased Carburetor Pressure on Engine Performance at Several Compression Ratios

NASA Technical Reports Server (NTRS)

Schey, Oscar W; Rollin, Vern G

1933-01-01

The object of this investigation was to determine the effect of increasing the carburetor pressures from 30 to 40 inches of mercury, at compression ratios from 3.5 to 7.5, on the power, on the maximum cylinder pressures, on the fuel consumption, and on the other performance characteristics of an engine. A roots-type aircraft-engine supercharger was used to maintain the desired carburetor pressure.

Children's Perceptions of Hypothetical Peers With Undesirable Characteristics: Role of the Peers' Desire to Change, Source of Effort to Change, and Outcome.

PubMed

Barnett, Mark A; Sonnentag, Tammy L; Wadian, Taylor W; Jones, Tucker L; Langley, Courtney A

2015-01-01

The present study, involving sixth- to eighth-grade students, is an extension of a prior investigation (Barnett, Livengood, Sonnentag, Barlett, & Witham, 2010) that examined children's perceptions of hypothetical peers with various undesirable characteristics. Results indicate that children's perceptions of hypothetical peers with an undesirable characteristic are influenced by the peers' desire to change, the source of effort to change, and the peers' success or failure in changing the characteristic. The children anticipated responding more favorably to peers who were successful in overcoming an undesirable characteristic than peers who were unsuccessful. Regardless of the peers' outcome, the children anticipated responding more favorably to peers who tried to change than peers who relied on the effort of adult authorities to motivate change. The children perceived successful peers as experiencing more positive affect than their unsuccessful counterparts, especially if the success was presented as a fulfillment of the peers' desire to change their undesirable characteristic. Finally, the children's ratings reflected the belief that, among peers who failed to change their undesirable characteristic, lacking the desire to change increases the relative likelihood that the characteristic will be permanent.

Survey of currently available high-resolution raster graphics systems

NASA Technical Reports Server (NTRS)

Jones, Denise R.

1987-01-01

Presented are data obtained on high-resolution raster graphics engines currently available on the market. The data were obtained through survey responses received from various vendors and also from product literature. The questionnaire developed for this survey was basically a list of characteristics desired in a high performance color raster graphics system which could perform real-time aircraft simulations. Several vendors responded to the survey, with most reporting on their most advanced high-performance, high-resolution raster graphics engine.

Locked-wrap fuel rod

DOEpatents

Kaplan, Samuel; Chertock, Alan J.; Punches, James R.

1977-01-01

A method for spacing fast reactor fuel rods using a wire wrapper improved by orienting the wire-wrapped fuel rods in a unique manner which introduces desirable performance characteristics not attainable by previous wire-wrapped designs. Use of this method in a liquid metal fast breeder reactor results in: (a) improved mechanical performance, (b) improved rod-to-rod contact, (c) reduced steel volume, and (d) improved thermal-hydraulic performance. The method produces a "locked wrap" design which tends to lock the rods together at each of the wire cluster locations.

Robustness. [in space systems

NASA Technical Reports Server (NTRS)

Ryan, Robert

1993-01-01

The concept of rubustness includes design simplicity, component and path redundancy, desensitization to the parameter and environment variations, control of parameter variations, and punctual operations. These characteristics must be traded with functional concepts, materials, and fabrication approach against the criteria of performance, cost, and reliability. The paper describes the robustness design process, which includes the following seven major coherent steps: translation of vision into requirements, definition of the robustness characteristics desired, criteria formulation of required robustness, concept selection, detail design, manufacturing and verification, operations.

Performance Testing of Yardney MCMB-LiNiCoAlO2 Lithium-ion Cells Possessing Electrolytes with Improved Safety Characteristics

NASA Technical Reports Server (NTRS)

Smart, Marshall C.; Whitcanack, Larry D.; Krause, Frederick C.; Hwang, Constanza; Bugga, Ratnakumar V.; Santee, Stuart; Puglia, Frank J.; Gitzendanner, Rob

2012-01-01

Many future NASA missions aimed at exploring the Moon and Mars require high specific energy rechargeable batteries that possess enhanced safety characteristics. There is also a strong desire to develop Li-ion batteries with improved safety characteristics for terrestrial applications, most notably for HEV and PHEV automotive applications. In previous work focused upon evaluating various potential flame retardant additives1, triphenyl phosphate (TPP)2 was observed to have the most desirable attributes, including good life characteristics and resilience to high voltage operation. We have employed a number of approaches in the design of promising TPP-based electrolytes with improved safety, including: (a) varying the flame retardant additive (FRA) content (from 5 to 15%), (b) the use of fluorinated co-solvents, (c) the use of additives to improve compatibility, and (c) the use of ester co-solvents to decrease the viscosity and increase the conductivity. In recent work, we have demonstrated a number of these electrolyte formulations to be compatible with a number of chemistries, including: MCMB carbon-LiNi0.8Co0.2O2, graphite-LiNi0.8Co0.15Al0.05O2, Li-Li(Li0.17Ni 0.25 Mn 0.58 )O2, Li-LiNiCoMnO2 and graphite- LiNiCoMnO2.3,4 In the current study, we have demonstrated the performance of a number of TPP-containing electrolytes in 7 Ah prototype MCMB-LiNiCoO2 cells. We will describe the results of a number of performance tests, including: a) 100% DOD cycle life testing at various temperatures, b) discharge rate characterization as a function of temperature, c) charge rate characterization as a function of temperature, and d) impedance as a function of temperature. In addition to displaying good life characteristics, being comparable to baseline chemistries, a number of cells were observed to provide good performance over a wide temperature range.

Planning for an uncertain future: Restoration to mitigate water scarcity and sustain carbon sequestration

Treesearch

Steven T. Brantley; James M. Vose; David N. Wear; Larry Band

2018-01-01

The desired future conditions of longleaf pine (Pinus palustris) can be described by ecosystem structural characteristics as well as by the provision of ecosystem services. Although the desired structural characteristics of restored longleaf pine ecosystems have been described at length, these characteristics deserve a brief review here because...

Electric propulsion for near-Earth space missions

NASA Technical Reports Server (NTRS)

Terwilliger, C. H.; Smith, W. W.

1980-01-01

A set of missions was postulated that was considered to be representative of those likely to be desirable/feasible over the next three decades. The characteristics of these missions, and their payloads, that most impact the choice/design of the requisite propulsion system were determined. A system-level model of the near-Earth transportation process was constructed, which incorporated these mission/system characteristics, as well as the fundamental parameters describing the technology/performance of an ion bombardment based electric propulsion system. The model was used for sensitivity studies to determine the interactions between the technology descriptors and program costs, and to establish the most cost-effective directions for technology advancement. The most important factor was seen to be the costs associated with the duration of the mission, and this in turn makes the development of advanced electric propulsion systems having moderate to high efficiencies ( 50 percent) at intermediate ranges of specific impulse (approximately 1000 seconds) very desirable.

Predictors of Behavior and Performance in Extreme Environments: The Antarctic Space Analogue Program

NASA Technical Reports Server (NTRS)

Palinkas, Lawrence A.; Gunderson, E K. Eric; Holland, A. W.; Miller, Christopher; Johnson, Jeffrey C.

2000-01-01

To determine which, if any, characteristics should be incorporated into a select-in approach to screening personnel for long-duration spaceflight, we examined the influence of crewmember social/ demographic characteristics, personality traits, interpersonal needs, and characteristics of station physical environments on performance measures in 657 American men who spent an austral winter in Antarctica between 1963 and 1974. During screening, subjects completed a Personal History Questionnaire which obtained information on social and demographic characteristics, the Deep Freeze Opinion Survey which assessed 5 different personality traits, and the Fundamental Interpersonal Relations Orientation-Behavior (FIRO-B) Scale which measured 6 dimensions of interpersonal needs. Station environment included measures of crew size and severity of physical environment. Performance was assessed on the basis of combined peer-supervisor evaluations of overall performance, peer nominations of fellow crewmembers who made ideal winter-over candidates, and self-reported depressive symptoms. Social/demographic characteristics, personality traits, interpersonal needs, and characteristics of station environments collectively accounted for 9-17% of the variance in performance measures. The following characteristics were significant independent predictors of more than one performance measure: military service, low levels of neuroticism, extraversion and conscientiousness, and a low desire for affection from others. These results represent an important first step in the development of select-in criteria for personnel on long-duration missions in space and other extreme environments. These criteria must take into consideration the characteristics of the environment and the limitations they place on meeting needs for interpersonal relations and task performance, as well as the characteristics of the individuals and groups who live and work in these environments.

MM-122: High speed civil transport

NASA Technical Reports Server (NTRS)

Demarest, Bill; Anders, Kurt; Manchec, John; Yang, Eric; Overgaard, Dan; Kalkwarf, Mike

1992-01-01

The rapidly expanding Pacific Rim market along with other growing markets indicates that the future market potential for a high speed civil transport is great indeed. The MM-122 is the answer to the international market desire for a state of the art, long range, high speed civil transport. It will carry 250 passengers a distance of 5200 nm at over twice the speed of sound. The MM-122 is designed to incorporate the latest technologies in the areas of control systems, propulsions, aerodynamics, and materials. The MM-122 will accomplish these goals using the following design parameters. First, a double delta wing planform with highly swept canards and an appropriately area ruled fuselage will be incorporated to accomplish desired aerodynamic characteristics. Propulsion will be provided by four low bypass variable cycle turbofan engines. A quad-redundant fly-by-wire flight control system will be incorporated to provide appropriate static stability and level 1 handling qualities. Finally, the latest in conventional metallic and modern composite materials will be used to provide desired weight and performance characteristics. The MM-122 incorporates the latest in technology and cost minimization techniques to provide a viable solution to this future market potential.

Educational History, Employment Characteristics, and Desired Competencies of Doctoral-Educated Athletic Trainers

PubMed Central

West, Thomas F.; Buckley, W. E.; Denegar, Craig R.

2001-01-01

Objective: The study had 3 objectives: (1) to assess the educational history of doctoral-educated certified athletic trainers (ATCs) who work at academic institutions, (2) to determine the current employment characteristics of doctoral-educated ATCs who work at academic institutions, and (3) to identify which competencies doctoral-educated ATCs feel are important for new doctoral graduates to possess upon graduation. Design and Setting: Multiple sources were used to identify doctoral-educated ATCs who work at academic institutions. These individuals were surveyed to assess their educational histories, current employment characteristics, and opinions on desired competencies for new doctoral graduates. Data were analyzed using descriptive and inferential statistics. Subjects: Surveys were sent to 130 individuals, and the response rate was 89.2% (n = 116). Measurements: Subjects answered questions regarding their educational history and employment characteristics. A 5-point Likert scale was used to assess the importance of 22 competencies for new doctoral graduates to possess upon graduation. Comparisons were made between program directors and non–program directors, respondents employed at doctoral-granting institutions and non–doctoral-granting institutions, and doctoral student advisors and non-advisors. Results: Subjects reported several different educational backgrounds, job titles, and job responsibilities. Significant differences in job responsibilities and assessment of desired competencies were found between program directors and non–program directors, employees of doctoral-granting institutions and non–doctoral-granting institutions, and doctoral student advisors and non-advisors. Conclusions: As new doctoral programs are established in athletic training, students should receive training as classroom instructors and program administrators, in addition to learning the skills necessary to perform independent research in athletic training. PMID:12937515

Control of plasma process by use of harmonic frequency components of voltage and current

DOEpatents

Miller, Paul A.; Kamon, Mattan

1994-01-01

The present invention provides for a technique for taking advantage of the intrinsic electrical non-linearity of processing plasmas to add additional control variables that affect process performance. The technique provides for the adjustment of the electrical coupling circuitry, as well as the electrical excitation level, in response to measurements of the reactor voltage and current and to use that capability to modify the plasma characteristics to obtain the desired performance.

Personality and mate preferences: five factors in mate selection and marital satisfaction.

PubMed

Botwin, M D; Buss, D M; Shackelford, T K

1997-03-01

Although personality characteristics figure prominently in what people want in a mate, little is known about precisely which personality characteristics are most important, whether men and women differ in their personality preferences, whether individual women or men differ in what they want, and whether individuals actually get what they want. To explore these issues, two parallel studies were conducted, one using a sample of dating couples (N = 118) and one using a sample of married couples (N = 216). The five-factor model, operationalized in adjectival form, was used to assess personality characteristics via three data sources-self--report, partner report, and independent interviewer reports. Participants evaluated on a parallel 40-item instrument their preferences for the ideal personality characteristics of their mates. Results were consistent across both studies. Women expressed a greater preference than men for a wide array of socially desirable personality traits. Individuals differed in which characteristics they desired, preferring mates who were similar to themselves and actually obtaining mates who embodied what they desired. Finally, the personality characteristics of one's partner significantly predicted marital and sexual dissatisfaction, most notably when the partner was lower on Agreeableness, Emotional Stability, and Intellect-Openness than desired.

CHARACTERISTICS OF FARM WORKERS AS RELATED TO STABILIZATION OF THE WORK FORCE.

ERIC Educational Resources Information Center

METZLER, WILLIAM H.

PROBLEMS OF THE MIGRANTS INCLUDE THEIR LACK OF DESIRE TO LEARN NEW SKILLS AND TO ADJUST TO NEW SITUATIONS, THEIR NEED TO MIGRATE TO FIND EMPLOYMENT DURING CERTAIN OFF-SEASONS, THEIR LACK OF TRAINING FOR MANY KINDS OF JOBS, THEIR PREJUDICED ATTITUDE TOWARD JOBS MAINLY PERFORMED BY FOREIGN OR COLORED WORKERS, THEIR TENDENCY TO LEAVE A JOB WHEN…

Improved performance and safety of lithium ion cells with the use of fluorinated carbonate-based electrolytes

NASA Technical Reports Server (NTRS)

Smart, M. C.; Ratnakumar, B. V.; Ryan, V. S.; Surampudi, S.; Prakashi, G. K. S.; Hu, J.; Cheung, I.

2002-01-01

There has been increasing interest in developing lithium-ion electrolytes that possess enhanced safety characteristics, while still able to provide the desired stability and performance. Toward this end, our efforts have been focused on the development of lithium-ion electrolytes which contain partially and fully fluorinated carbonate solvents. The advantage of using such solvents is that they possess the requisite stability demonstrated by the hydrocarbon-based carbonates, while also possessing more desirable physical properties imparted by the presence of the fluorine substituents, such as lower melting points, increased stability toward oxidation, and favorable SEI film forming Characteristics on carbon. Specifically, we have demonstrated the beneficial effect of electrolytes which contain the following fluorinated carbonate-based solvents: methyl 2,2,2-trifluoroethyl carbonate (MTFEC), ethyl-2,2,2 trifluoroethyl carbonate (ETFEC), propyl 2,2,2-trifluoroethyl carbonate (PTFEC), methyl-2,2,2,2',2',2' -hexafluoro-i-propyl carbonate (MHFPC), ethyl- 2,2,2,2',2',2' -hexafluoro-i-propyl carbonate (EHFPC), and di-2,2,2-trifluoroethyl carbonate (DTFEC). These solvents have been incorporated into multi-component ternary and quaternary carbonate-based electrolytes and evaluated in lithium-carbon and carbon-LiNio.8Coo.202 cells (equipped with lithium reference electrodes). In addition to determining the charge/discharge behavior of these cells, a number of electrochemical techniques were employed (i.e., Tafel polarization measurements, linear polarization measurements, and electrochemical impedance spectroscopy (EIS)) to further characterize the performance of these electrolytes, including the SEI formation characteristics and lithium intercalatiodde-intercalation kinetics. In addition to their evaluation in experimental cells, cyclic voltammetry (CV) and conductivity measurements were performed on select electrolyte formulations to further our understanding of the trends in stability and ionic mobility imparted by different alkyl substituents in linear carbonates.

Optimum structural design with static aeroelastic constraints

NASA Technical Reports Server (NTRS)

Bowman, Keith B; Grandhi, Ramana V.; Eastep, F. E.

1989-01-01

The static aeroelastic performance characteristics, divergence velocity, control effectiveness and lift effectiveness are considered in obtaining an optimum weight structure. A typical swept wing structure is used with upper and lower skins, spar and rib thicknesses, and spar cap and vertical post cross-sectional areas as the design parameters. Incompressible aerodynamic strip theory is used to derive the constraint formulations, and aerodynamic load matrices. A Sequential Unconstrained Minimization Technique (SUMT) algorithm is used to optimize the wing structure to meet the desired performance constraints.

Bilateral Impedance Control For Telemanipulators

NASA Technical Reports Server (NTRS)

Moore, Christopher L.

1993-01-01

Telemanipulator system includes master robot manipulated by human operator, and slave robot performing tasks at remote location. Two robots electronically coupled so slave robot moves in response to commands from master robot. Teleoperation greatly enhanced if forces acting on slave robot fed back to operator, giving operator feeling he or she manipulates remote environment directly. Main advantage of bilateral impedance control: enables arbitrary specification of desired performance characteristics for telemanipulator system. Relationship between force and position modulated at both ends of system to suit requirements of task.

Influence of social desirability on age differences in self-reports of mood and personality

PubMed Central

Soubelet, Andrea; Salthouse, Timothy A.

2011-01-01

Increased age has been found to be associated with differences in affect and personality which have been interpreted in terms of better emotional regulation and increased maturity. However, these findings have largely been based on self-report data, and the primary goal of the current research was to investigate the hypothesis that age-related differences in affect and in certain desirable personality traits might, at least partially, reflect age differences in social desirability. As expected, increased age was associated with lower levels of negative affect and neuroticism and higher levels of positive affect, life satisfaction, agreeableness and conscientiousness, and scores on the social desirability scale were positively related to age and to desirable self-report characteristics, but negatively related to undesirable self-report characteristics. Importantly, controlling for the variance in the social desirability measure resulted in less positive age trends in both types of self-report measures. PMID:21682727

Using Probiotics and Prebiotics to Manage the Gastrointestinal Tract Ecosystem

NASA Astrophysics Data System (ADS)

Buddington, Randal

Natural and man-made ecosystems are routinely managed to increase productivity and provide desired characteristics. The management approaches most commonly used include the addition of desired organisms, provision of fertilizers or feeds to encourage desired species, alteration of the physical or chemical features of the environment, and the selective removal of undesirable species. The selection of specific management strategies and their success are dependent on a thorough understanding of existing ecosystem characteristics and the short and long-term responses to the management strategy.

Characteristics of Athletic Training Students That Preceptors Find Desirable

ERIC Educational Resources Information Center

Carr, W. David; Thomas, Spencer; Paulsen, Jenica; Chiu, Jennifer

2016-01-01

Context: Athletic training students acquire clinical hours under the direct supervision of athletic training preceptors. Objective: The purpose of this project was to explore what characteristics preceptors desire in their athletic training students. Design and Setting: Online survey instrument. Patients or Other Participants: A total of 286…

Wake topology of under-actuated rajiform batoid robots

NASA Astrophysics Data System (ADS)

Valdivia Y Alvarado, Pablo; Weymouth, Gabriel; Thekoodan, Dilip; Patrikalakis, Nicholas

2011-11-01

Under-actuated continuous soft robots are designed to have modes of vibration that match desired body motions using minimal actuation. The desired modes of vibration are enabled by flexible continuous bodies with heterogenous material distributions. Errors or intentional approximations in the manufactured material distributions alter the achieved body motions and influence the resulting locomotion performance. An under-actuated continuous soft robot designed to mimic rajiform batoids such as stingrays is used to investigate the influence that fin kinematics variations have on wake topology, and the trade-offs that simplifying the body material structure has on achievable swimming performance. Pectoral fin kinematics in rajiform batoids are defined by traveling waves along the fin cord with particular amplitude envelopes along both the fin cord and span. Digital particle image velocimetry (DPIV) analysis of a prototype's wake structure and immersed-boundary numerical simulations are used to clarify the role of traveling wave wavelength, fin flapping frequency, and amplitude envelope characteristics on the resulting wake topology and swimming performance.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoessel, Chris

2013-11-13

This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency ofmore » a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.« less

Method for Predicting the Energy Characteristics of Li-Ion Cells Designed for High Specific Energy

NASA Technical Reports Server (NTRS)

Bennett, William, R.

2012-01-01

Novel electrode materials with increased specific capacity and voltage performance are critical to the NASA goals for developing Li-ion batteries with increased specific energy and energy density. Although performance metrics of the individual electrodes are critically important, a fundamental understanding of the interactions of electrodes in a full cell is essential to achieving the desired performance, and for establishing meaningful goals for electrode performance in the first place. This paper presents design considerations for matching positive and negative electrodes in a viable design. Methods for predicting cell-level performance, based on laboratory data for individual electrodes, are presented and discussed.

Covariance of engineering management characteristics with engineering employee performance

NASA Astrophysics Data System (ADS)

Hesketh, Andrew Arthur

1998-12-01

As business in the 1990's grapples with the impact of continuous improvement and quality to meet market demands, there is an increased need to improve the leadership capabilities of our managers. Engineers have indicated desire for certain managerial characteristics in their leadership but there have been no studies completed that approached the problem of determining what managerial characteristics were best at improving employee performance. This study addressed the idea of identifying certain managerial characteristics that enhance employee performance. In the early 1990's, McDonnell Douglas Aerospace in St. Louis used a forced distribution system and allocated 35% of its employees into a "exceeds expectations" category and 60% into a "meets expectations" category. A twenty-question 5 point Likert scale survey on managerial capabilities was administered to a sample engineering population that also obtained their "expectations" category. A single factor ANOVA on the survey results determined a statistical difference between the "exceeds" and "meets" employees with four of the managerial capability questions. The "exceeds expectations" employee indicated that supervision did a better job of supporting subordinate development, clearly communicating performance expectations, and providing timely performance feedback when compared to the "meets expectations" employee. The "meets expectations" employee felt that their opinions, when different from their supervisor's, were more often ignored when compared to the "exceeds expectations" employee. These four questions relate to two specific managerial characteristics, "gaining (informal) authority and support" or "control" characteristic and "providing assistance and guidance" or "command" characteristic, that can be emphasized in managerial training programs.

Romantic partners in a market perspective: expectations about what ensures a highly desirable partner.

PubMed

Castro, Felipe N; Hattori, Wallisen T; Yamamoto, Maria Emília; Lopes, Fívia A

2013-10-01

This study used the biological market perspective and influential statistical models from the marketing field to investigate males' and females' expectations regarding which combination of characteristics are most relevant in ensuring desirable partnerships for same-sex individuals. Thus, 358 Brazilian undergraduates assessed eight descriptions of same-gender stimulus targets (formulated with different levels of physical attractiveness, social skills, and current or prospective social status) and evaluated the overall desirability of the targets' expected or probable partners. From the possible combinations, three groups emerged: for one group, mainly composed of men, status characteristics were the most important attributes; for the others, mostly composed of women, social skills or physical characteristics were identified as most important in appealing to a desirable partner. This work expands the understanding of variability in male and female romantic expectations, and its implications are discussed from an evolutionary perspective.

Performance, emissions, and physical characteristics of a rotating combustion aircraft engine

NASA Technical Reports Server (NTRS)

Berkowitz, M.; Hermes, W. L.; Mount, R. E.; Myers, D.

1976-01-01

The RC2-75, a liquid cooled two chamber rotary combustion engine (Wankel type), designed for aircraft use, was tested and representative baseline (212 KW, 285 BHP) performance and emissions characteristics established. The testing included running fuel/air mixture control curves and varied ignition timing to permit selection of desirable and practical settings for running wide open throttle curves, propeller load curves, variable manifold pressure curves covering cruise conditions, and EPA cycle operating points. Performance and emissions data were recorded for all of the points run. In addition to the test data, information required to characterize the engine and evaluate its performance in aircraft use is provided over a range from one half to twice its present power. The exhaust emissions results are compared to the 1980 EPA requirements. Standard day take-off brake specific fuel consumption is 356 g/KW-HR (.585 lb/BHP-HR) for the configuration tested.

Perform - A performance optimizing computer program for dynamic systems subject to transient loadings

NASA Technical Reports Server (NTRS)

Pilkey, W. D.; Wang, B. P.; Yoo, Y.; Clark, B.

1973-01-01

A description and applications of a computer capability for determining the ultimate optimal behavior of a dynamically loaded structural-mechanical system are presented. This capability provides characteristics of the theoretically best, or limiting, design concept according to response criteria dictated by design requirements. Equations of motion of the system in first or second order form include incompletely specified elements whose characteristics are determined in the optimization of one or more performance indices subject to the response criteria in the form of constraints. The system is subject to deterministic transient inputs, and the computer capability is designed to operate with a large linear programming on-the-shelf software package which performs the desired optimization. The report contains user-oriented program documentation in engineering, problem-oriented form. Applications cover a wide variety of dynamics problems including those associated with such diverse configurations as a missile-silo system, impacting freight cars, and an aircraft ride control system.

Couple Characteristics and Contraceptive Use among Women and their Partners in Urban Kenya

PubMed Central

Irani, Laili; Speizer, Ilene S.; Fotso, Jean-Christophe

2014-01-01

Background Few studies have used couple data to identify individual- and relationship-level characteristics that affect contraceptive use in urban areas. Using matched couple data from urban Kenya collected in 2010, this study determines the association between relationship-level characteristics (desire for another child, communication about desired number of children and FP use) and contraceptive use and intention to use among non-users. Methods Data were collected from three Kenyan cities: Nairobi, Mombasa and Kisumu. Baseline population-based survey data from the Measurement, Learning & Evaluation Project were used to identify 883couples (weighted value=840). Multivariate regressions used the couple as the unit of analysis. Results Almost two-thirds of couples currently used contraception. Adjusting for individual- and environmental-level characteristics, couples who desired another child were less likely to use contraception than couples wanting more children. In addition, couples where both partners reported communicating with each other regarding desired number of children and FP use were more likely to use contraception compared to couples that did not communicate. Analyses testing the association of relationship-level characteristics and intention to use contraception, among non-users, resembled those of current contraceptive users. Conclusion Couple-level characteristics are associated with current contraceptive use and future intent to use. Couples that discussed their desired number of children and FP use were more likely to use contraception than couples that did not communicate with each other. FP programs should identify strategies to improve communication in FP among couples and to ensure better cooperation between partners. PMID:24733057

Method and apparatus for calibrating a tiled display

NASA Technical Reports Server (NTRS)

Chen, Chung-Jen (Inventor); Johnson, Michael J. (Inventor); Chandrasekhar, Rajesh (Inventor)

2001-01-01

A display system that can be calibrated and re-calibrated with a minimal amount of manual intervention. To accomplish this, one or more cameras are provided to capture an image of the display screen. The resulting captured image is processed to identify any non-desirable characteristics, including visible artifacts such as seams, bands, rings, etc. Once the non-desirable characteristics are identified, an appropriate transformation function is determined. The transformation function is used to pre-warp the input video signal that is provided to the display such that the non-desirable characteristics are reduced or eliminated from the display. The transformation function preferably compensates for spatial non-uniformity, color non-uniformity, luminance non-uniformity, and other visible artifacts.

Method and system for simulating heat and mass transfer in cooling towers

DOEpatents

Bharathan, Desikan; Hassani, A. Vahab

1997-01-01

The present invention is a system and method for simulating the performance of a cooling tower. More precisely, the simulator of the present invention predicts values related to the heat and mass transfer from a liquid (e.g., water) to a gas (e.g., air) when provided with input data related to a cooling tower design. In particular, the simulator accepts input data regarding: (a) cooling tower site environmental characteristics; (b) cooling tower operational characteristics; and (c) geometric characteristics of the packing used to increase the surface area within the cooling tower upon which the heat and mass transfer interactions occur. In providing such performance predictions, the simulator performs computations related to the physics of heat and mass transfer within the packing. Thus, instead of relying solely on trial and error wherein various packing geometries are tested during construction of the cooling tower, the packing geometries for a proposed cooling tower can be simulated for use in selecting a desired packing geometry for the cooling tower.

Test and evaluation of constant-flow devices for use in SSN AFFF proportioning systems. Interim report, January-May 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, F.W.; Back, G.G.; Burns, R.E.

1986-11-04

Constant flow devices, which deliver a constant flow of liquid over a range of upstream and downstream pressures, have been suggested as an alternative to orifice plates for proportioning AFFF in SSN 21 fire-suppression systems. Operational and performance characteristics of two lightweight, inexpensive, commercially available constant-flow devices have significant advantages over orifice plates. Both models tested, however, showed performance degradation when subjected to simulated service conditions. A constant flow device with improved resistance to wear and to AFFF exposure is desirable. Since the constant-flow control devices tested improves proportioning efficiency but do not have optimum characteristics, investigation of improved devicesmore » or methods is recommended.« less

Design philosophy of the Jet Propulsion Laboratory infrared detector test facility

NASA Technical Reports Server (NTRS)

Burns, R.; Blessinger, M. A.

1983-01-01

To support the development of advanced infrared remote sensing instrumentation using line and area arrays, a test facility has been developed to characterize the detectors. The necessary performance characteristics of the facility were defined by considering current and projected requirements for detector testing. The completed facility provides the desired level of detector testing capability as well as providing ease of human interaction.

Reduced Toxicity High Performance Monopropellant

DTIC Science & Technology

2011-09-01

M315E Distribution A: Approved for public release; distribution unlimited AF - M315E Desirable Properties Characteristic Objective D it *I 3450 N /L...required AF M315E d- excee s SOTA monopropellant (45%) and bipropellant (8%) Next generation exceeds SOTA monopropellant (66%) and bipropellant (23...inert mass fraction Distribution A: Approved for public release; distribution unlimited Toxicity Assessment of AF - M315E Toxicity Testing Results

Gifted Israeli Students' Perceptions of Teachers' Desired Characteristics: A Case of Cultural Orientation

ERIC Educational Resources Information Center

Eilam, Billie; Vidergor, Hava E.

2011-01-01

Gifted students' perceptions of the desired characteristics of teachers of the gifted were assessed from a sample comprised of 404 elementary- and junior high-school Israeli Jewish and Arab students studying in pullout centers. Perceptions were measured using a questionnaire comprising teachers' cognitive, personal, and pedagogical dimensions.…

Enhancing the Undergraduate Industrial Engineering Curriculum: Defining Desired Characteristics and Emerging Topics

ERIC Educational Resources Information Center

Eskandari, Hamidreza; Sala-Diakanda, Serge; Furterer, Sandra; Rabelo, Luis; Crumpton-Young, Lesia; Williams, Kent

2007-01-01

Purpose: This paper aims to present the results of an initial research study conducted to identify the desired professional characteristics of an industrial engineer with an undergraduate degree and the emerging topic areas that should be incorporated into the curriculum to prepare industrial engineering (IE) graduates for the future workforce.…

Some factors affecting the use of lighter than air systems. [economic and performance estimates for dirigibles and semi-buoyant hybrid vehicles

NASA Technical Reports Server (NTRS)

Havill, C. D.

1974-01-01

The uses of lighter-than-air vehicles are examined in the present day transportation environment. Conventional dirigibles were found to indicate an undesirable economic risk due to their low speeds and to uncertainties concerning their operational use. Semi-buoyant hybrid vehicles are suggested as an alternative which does not have many of the inferior characteristics of conventional dirigibles. Economic and performance estimates for hybrid vehicles indicate that they are competitive with other transportation systems in many applications, and unique in their ability to perform some highly desirable emergency missions.

A tyre slip-based integrated chassis control of front/rear traction distribution and four-wheel independent brake from moderate driving to limit handling

NASA Astrophysics Data System (ADS)

Joa, Eunhyek; Park, Kwanwoo; Koh, Youngil; Yi, Kyongsu; Kim, Kilsoo

2018-04-01

This paper presents a tyre slip-based integrated chassis control of front/rear traction distribution and four-wheel braking for enhanced performance from moderate driving to limit handling. The proposed algorithm adopted hierarchical structure: supervisor - desired motion tracking controller - optimisation-based control allocation. In the supervisor, by considering transient cornering characteristics, desired vehicle motion is calculated. In the desired motion tracking controller, in order to track desired vehicle motion, virtual control input is determined in the manner of sliding mode control. In the control allocation, virtual control input is allocated to minimise cost function. The cost function consists of two major parts. First part is a slip-based tyre friction utilisation quantification, which does not need a tyre force estimation. Second part is an allocation guideline, which guides optimally allocated inputs to predefined solution. The proposed algorithm has been investigated via simulation from moderate driving to limit handling scenario. Compared to Base and direct yaw moment control system, the proposed algorithm can effectively reduce tyre dissipation energy in the moderate driving situation. Moreover, the proposed algorithm enhances limit handling performance compared to Base and direct yaw moment control system. In addition to comparison with Base and direct yaw moment control, comparison the proposed algorithm with the control algorithm based on the known tyre force information has been conducted. The results show that the performance of the proposed algorithm is similar with that of the control algorithm with the known tyre force information.

Simulation and Experimental Investigation of Structural Dynamic Frequency Characteristics Control

PubMed Central

Zhang, Xingwu; Chen, Xuefeng; You, Shangqin; He, Zhengjia; Li, Bing

2012-01-01

In general, mechanical equipment such as cars, airplanes, and machine tools all operate with constant frequency characteristics. These constant working characteristics should be controlled if the dynamic performance of the equipment demands improvement or the dynamic characteristics is intended to change with different working conditions. Active control is a stable and beneficial method for this, but current active control methods mainly focus on vibration control for reducing the vibration amplitudes in the time domain or frequency domain. In this paper, a new method of dynamic frequency characteristics active control (DFCAC) is presented for a flat plate, which can not only accomplish vibration control but also arbitrarily change the dynamic characteristics of the equipment. The proposed DFCAC algorithm is based on a neural network including two parts of the identification implement and the controller. The effectiveness of the DFCAC method is verified by several simulation and experiments, which provide desirable results. PMID:22666072

Simulation and experimental investigation of structural dynamic frequency characteristics control.

PubMed

Zhang, Xingwu; Chen, Xuefeng; You, Shangqin; He, Zhengjia; Li, Bing

2012-01-01

In general, mechanical equipment such as cars, airplanes, and machine tools all operate with constant frequency characteristics. These constant working characteristics should be controlled if the dynamic performance of the equipment demands improvement or the dynamic characteristics is intended to change with different working conditions. Active control is a stable and beneficial method for this, but current active control methods mainly focus on vibration control for reducing the vibration amplitudes in the time domain or frequency domain. In this paper, a new method of dynamic frequency characteristics active control (DFCAC) is presented for a flat plate, which can not only accomplish vibration control but also arbitrarily change the dynamic characteristics of the equipment. The proposed DFCAC algorithm is based on a neural network including two parts of the identification implement and the controller. The effectiveness of the DFCAC method is verified by several simulation and experiments, which provide desirable results.

Desired Job Characteristics and Perceived Occupational Barriers Among Low-Income Youth in Kentucky. RS-60.

ERIC Educational Resources Information Center

Hall, Larry D.; Coleman, A. Lee

In 1975, 263 low-income Kentucky youths aged 17-19 completed questionnaires about career aspirations according to desired job characteristics and perceived barriers to occupational attainment; the sample (approximately half male, half female) was from an urban inner city area in Fayette County (approximately half black, half white) and the two…

Development of Program for Enhancing the Ideal Desirable Characteristic of Basic School Administrators

ERIC Educational Resources Information Center

Khakhlong, Chettha; Julsuwan, Suwat; Somprach, Kanokorn; Khangpheng, Samrit

2015-01-01

The objective of this research is to develop a program for enhancing ideal desirable characteristic of basic school administrators. An in-depth interview was done with experts. The opinions of school administrators, assistant school administrators, and teachers as the chiefs of academic work were found out. A total of 330 persons participated in…

Israeli Teachers' Perceptions of Gifted Teachers' Desired Characteristics: A Case of Cultural Orientation

ERIC Educational Resources Information Center

Vidergor, Hava E.; Eilam, Billie

2012-01-01

The aim of this study was to assess Israeli Jewish and Arab teachers' perceptions of the desired characteristics of teachers of the gifted. The research sample comprised 217 teachers (134 Jews and 83 Arabs) representing three groups: (a) teachers entering a professional development program for teachers of gifted students; (b) teachers of gifted…

Planning for success: desired characteristics of special operations surgeons, a pilot study.

PubMed

Campbell, Barrett H; Alderman, Shawn M

2012-01-01

Selection criteria for Special Operations Forces (SOF) physicians are often unclear to potential candidates without prior SOF experience. To date, no published career resource exists to guide the careers of physicians interested in becoming a SOF surgeon. Using a survey tool, desirable characteristics and personal attributes were identified that can be used to inform candidate career decisions and better prepare them for a future position in Special Operations. A descriptive, cross-sectional survey instrument was developed and distributed to current Army SOF Command Surgeons for further distribution to subordinate surgeons. RESULTS were analyzed as a cohort and by subordinate command. Respondents consisted of current SOF Surgeons. Uniformly, the individual characteristics most strongly desired are professionalism, being a team player, and leadership. Possessing or obtaining Airborne and Flight Surgeon qualifications prior to consideration for a surgeon position was highly desired. Residency training within Family Medicine or Emergency Medicine constituted the vast majority of specialty preference. Understanding which characteristics and attributes are desirable to current surgeons and commanders can aid physicians interested in SOF surgeon positions. Using this study and future studies can guide career planning and foster the selection of ideally trained physicians who will operate at the tip of the spear. The views expressed are those of the author(s) and do not reflect the official policy of the Department of the Army, the Department of Defense or the U.S. Government. 2012.

Analysis of integrated photovoltaic-thermal systems using solar concentrators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusoff, M.B.

1983-01-01

An integrated photovoltaic-thermal system using solar concentrators utilizes the solar radiation spectrum in the production of electrical and thermal energy. The electrical conversion efficiency of this system decreases with increasing solar cell temperature. Since a high operating temperature is desirable to maximize the quality of thermal output of the planned integrated system, a proper choice of the operating temperature for the unit cell is of vital importance. The analysis predicts performance characteristics of the unit cell by considering the dependence of the heat generation, the heat absorption and the heat transmission on the material properties of the unit cell structure.more » An analytical model has been developed to describe the heat transport phenomena occurring in the unit cell structure. The range of applicability of the one-dimensional and the two-dimensional models, which have closed-form solutions, has been demonstrated. Parametric and design studies point out the requirements for necessary good electrical and thermal performance. A procedure utilizing functional forms of component characteristics in the form of partial coefficients of the dependent variable has been developed to design and operate the integrated system to have a desirable value of the thermal to electrical output ratio both at design and operating modes.« less

Technique Using Axicons For Generating Flat Top Laser Beam Profiles

NASA Astrophysics Data System (ADS)

Viswanathan, V. K.; Woodfin, G. L.; Stahl, D.; Carpenter, J. P.; Kyrala, G.

1983-11-01

In certain fusion experiments using CO2 lasers, like Helios, it is desired to produce a focal spot several times larger than the nominal focal spot, with a flat beam profile. The typical focal spot in Helios is roughly 70 μm and just defocussing the beam produces beam breakup, with several hot spots with roughly the original diameter, and a gaussian distribution. A number of schemes were tried to achieve a large spot with desired characteristics. These are described in the article. Axicons were found to produce spots with desired characteristics. Axicons are lenses or mirrors having a cone-shaped surface. The various schemes are described, as well as an. experiment in Helios which confirmed that axicons produced the spots with desirable characteristics. Helios is an 8-beam CO2 laser which produces 10 kJ at power in excess of 20 TW. It is currently being used for Laser Fusion studies at the Los Alamos National Laboratory.

Decentralized PID controller for TITO systems using characteristic ratio assignment with an experimental application.

PubMed

Hajare, V D; Patre, B M

2015-11-01

This paper presents a decentralized PID controller design method for two input two output (TITO) systems with time delay using characteristic ratio assignment (CRA) method. The ability of CRA method to design controller for desired transient response has been explored for TITO systems. The design methodology uses an ideal decoupler to reduce the interaction. Each decoupled subsystem is reduced to first order plus dead time (FOPDT) model to design independent diagonal controllers. Based on specified overshoot and settling time, the controller parameters are computed using CRA method. To verify performance of the proposed controller, two benchmark simulation examples are presented. To demonstrate applicability of the proposed controller, experimentation is performed on real life interacting coupled tank level system. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Characteristics of Health Educators Desired by Inner-City Health Clinic Patients: A Case Study

ERIC Educational Resources Information Center

Price, James; Sidani, Jaime

2007-01-01

A group (n = 170) of inner-city, predominantly African American, health clinic patients were asked to identify the characteristics they desired in a new clinic health educator. A plurality (44%) of the patients perceived a bachelor's degree would be a sufficient level of education. The vast majority of patients claimed the sex of the health…

Tentative guides for the selection of plus trees and superior stands in Douglas-fir.

Treesearch

Leo A. Isaac

1955-01-01

Interest among foresters in forest tree improvement has increased rapidly in recent years. Geneticists have learned that some individual trees greatly excel their neighbors in desirable characteristics, and that some entire stands are superior to other stands of the same species in a general locality. They have learned that many of the desirable tree characteristics...

Methods of Constructing a Blended Performance Function Suitable for Formation Flight

NASA Technical Reports Server (NTRS)

Ryan, John J.

2017-01-01

This paper presents two methods for constructing an approximate performance function of a desired parameter using correlated parameters. The methods are useful when real-time measurements of a desired performance function are not available to applications such as extremum-seeking control systems. The first method approximates an a priori measured or estimated desired performance function by combining real-time measurements of readily available correlated parameters. The parameters are combined using a weighting vector determined from a minimum-squares optimization to form a blended performance function. The blended performance function better matches the desired performance function mini- mum than single-measurement performance functions. The second method expands upon the first by replacing the a priori data with near-real-time measurements of the desired performance function. The resulting blended performance function weighting vector is up- dated when measurements of the desired performance function are available. Both methods are applied to data collected during formation- flight-for-drag-reduction flight experiments.

Like mother, like child: Offspring marital timing desires and maternal marriage timing and stability.

PubMed

Arocho, Rachel; Kamp Dush, Claire M

2017-04-01

Understanding the determinants of marital timing is critical because it has implications for marital functioning and divorce. One salient predictor of marital timing is youth's desires for marriage timing. To shine light on predictors of both desires for marital timing and the timing of marriage itself, we examine offspring marital desires and maternal marriage characteristics in the National Longitudinal Survey of Youth, 1979 (NLSY79) cohort and 1979 Child and Young Adult cohort (NLSY79-CYA; biological offspring of the women in the 1979 cohort). Analyses showed that maternal cohabitation postdivorce predicted decreased expectations to ever marry in offspring. Maternal age at marriage was positively associated with offspring desires for age at marriage, but only for those whose mothers had not divorced. Maternal marital age was significantly associated with the offspring's transition into marriage even when controlling for the offspring's desires for marriage timing, but neither maternal marriage age nor offspring desires for marital timing were associated with the timing of entrance into cohabitation, whereas maternal divorce was associated with earlier cohabitation. Our findings suggest that maternal marriage characteristics, particularly divorce, are significant predictors of millennials' desires for and experiences with romantic relationships. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Air Force Training: Further Analysis and Planning Needed to Improve Effectiveness

DTIC Science & Technology

2016-09-01

training, and (3) established virtual training plans that include desirable characteristics of a comprehensive strategy. GAO reviewed Air Force training...requirements may not reflect current and emerging training needs, because the Air Force has not comprehensively reassessed the assumptions underlying them...include all desirable characteristics of a comprehensive strategy, such as a risk-based investment strategy or a time line for addressing training needs

Synaptic electronics: materials, devices and applications.

PubMed

Kuzum, Duygu; Yu, Shimeng; Wong, H-S Philip

2013-09-27

In this paper, the recent progress of synaptic electronics is reviewed. The basics of biological synaptic plasticity and learning are described. The material properties and electrical switching characteristics of a variety of synaptic devices are discussed, with a focus on the use of synaptic devices for neuromorphic or brain-inspired computing. Performance metrics desirable for large-scale implementations of synaptic devices are illustrated. A review of recent work on targeted computing applications with synaptic devices is presented.

Social Desirability Trait Is Associated with Self-Reported Vegetable Intake among Women Enrolled in the Special Supplemental Nutrition Program for Women, Infants, and Children.

PubMed

Di Noia, Jennifer; Cullen, Karen Weber; Monica, Dorothy

2016-12-01

The Special Supplemental Nutrition Program for Women, Infants, and Children (WIC) Fresh Start (WFS) is a randomized controlled trial of nutrition education to promote farmers' market fruit and vegetable (F/V) purchases and consumption among women enrolled in WIC. Using baseline data from WFS to examine associations between social desirability trait, the tendency to respond in a manner consistent with expected norms, and self-reported F/V intake and to determine whether associations, if found, are moderated by participant characteristics. Cross-sectional. Seven hundred forty-four women enrolled in WFS. The setting is a New Jersey-based WIC agency located in a densely populated urban area. Items assessing participant characteristics, a short form of the Marlowe-Crowne Social Desirability Scale, and validated measures of the frequency and quantity of F/V intake. Linear regression analysis to examine associations between social desirability trait and F/V intake and hierarchical regression analysis to test for moderation by participant characteristics of the associations between social desirability trait and F/V intake. Social desirability trait was significantly associated with times per day vegetables were reported to have been consumed (β=0.08, P=0.03). The association was moderated by breastfeeding status. Among breastfeeding women, social desirability trait was unrelated to reported intake, whereas among non-breastfeeding women, it was positively associated with intake (a 1-unit increase in the social desirability score was associated with a 0.12 increase in times per day vegetables were reported to have been consumed). Social desirability trait is associated with self-reported vegetable intake among WIC participants generally and non-breastfeeding participants in particular and should be assessed in these groups. Replication studies with comparative measures of "true intake" are needed to determine whether social desirability trait biases self-reports of vegetable intake or whether those with a high social desirability trait consume vegetables more often. Copyright © 2016 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Relationship Characteristics and Sexual Practices of African American Adolescent Girls Who Desire Pregnancy

ERIC Educational Resources Information Center

Davies, Susan L.; DiClemente, Ralph J.; Wingood, Gina M.; Person, Sharina D.; Crosby, Richard A.; Harrington, Kathleen F.; Dix, Emily S.

2004-01-01

This study examined associations between African American adolescent girls' desire to become pregnant and their sexual and relationship practices. Odds ratios and 95% confidence intervals were used to detect significant associations between pregnancy desire and the assessed correlates. Of 522 participants (14 to 18 years old), 67 (12.8%) were…

Diagnostic for two-mode variable valve activation device

DOEpatents

Fedewa, Andrew M

2014-01-07

A method is provided for diagnosing a multi-mode valve train device which selectively provides high lift and low lift to a combustion valve of an internal combustion engine having a camshaft phaser actuated by an electric motor. The method includes applying a variable electric current to the electric motor to achieve a desired camshaft phaser operational mode and commanding the multi-mode valve train device to a desired valve train device operational mode selected from a high lift mode and a low lift mode. The method also includes monitoring the variable electric current and calculating a first characteristic of the parameter. The method also includes comparing the calculated first characteristic against a predetermined value of the first characteristic measured when the multi-mode valve train device is known to be in the desired valve train device operational mode.

Requirements for the conceptual design of advanced underground coal extraction systems

NASA Technical Reports Server (NTRS)

Gangal, M. D.; Lavin, M. L.

1981-01-01

Conceptual design requirements are presented for underground coal mining systems having substantially improved performance in the areas of production cost and miner safety. Mandatory performance levels are also set for miner health, environmental impact, and coal recovery. In addition to mandatory design goals and constraints, a number of desirable system characteristics are identified which must be assessed in terms of their impact on production cost and their compatibility with other system elements. Although developed for the flat lying, moderately thick seams of Central Appalachia, these requirements are designed to be easily adaptable to other coals.

Some practical universal noiseless coding techniques, part 3, module PSl14,K+

NASA Technical Reports Server (NTRS)

Rice, Robert F.

1991-01-01

The algorithmic definitions, performance characterizations, and application notes for a high-performance adaptive noiseless coding module are provided. Subsets of these algorithms are currently under development in custom very large scale integration (VLSI) at three NASA centers. The generality of coding algorithms recently reported is extended. The module incorporates a powerful adaptive noiseless coder for Standard Data Sources (i.e., sources whose symbols can be represented by uncorrelated non-negative integers, where smaller integers are more likely than the larger ones). Coders can be specified to provide performance close to the data entropy over any desired dynamic range (of entropy) above 0.75 bit/sample. This is accomplished by adaptively choosing the best of many efficient variable-length coding options to use on each short block of data (e.g., 16 samples) All code options used for entropies above 1.5 bits/sample are 'Huffman Equivalent', but they require no table lookups to implement. The coding can be performed directly on data that have been preprocessed to exhibit the characteristics of a standard source. Alternatively, a built-in predictive preprocessor can be used where applicable. This built-in preprocessor includes the familiar 1-D predictor followed by a function that maps the prediction error sequences into the desired standard form. Additionally, an external prediction can be substituted if desired. A broad range of issues dealing with the interface between the coding module and the data systems it might serve are further addressed. These issues include: multidimensional prediction, archival access, sensor noise, rate control, code rate improvements outside the module, and the optimality of certain internal code options.

Rotordynamics and Design Methods of an Oil-Free Turbocharger

NASA Technical Reports Server (NTRS)

Howard, Samuel A.

1999-01-01

The feasibility of supporting a turbocharger rotor on air foil bearings is investigated based upon predicted rotordynamic stability, load accommodations, and stress considerations. It is demonstrated that foil bearings offer a plausible replacement for oil-lubricated bearings in diesel truck turbochargers. Also, two different rotor configurations are analyzed and the design is chosen which best optimizes the desired performance characteristics. The method of designing machinery for foil bearing use and the assumptions made are discussed.

Low jitter, low inductance solid dielectric switches.

PubMed

Guenther, A H; Strickland, D M; Bettis, J R

1979-11-01

It has been shown that the use of graded solid dielectric sandwiches in laser-triggered spark gaps (LTS) can lead to highly desirable multichannel operations while maintaining the low delay and jitter performance characteristics of LTS. As many as ten separate breakdown channels were observed when small circular or hexagonal aluminum inserts were inserted between two Mylar dielectric sheets stressed at 4.1 kV/mil. A reduction in rise time was noted for these multichannel switching events.

A high-performance liquid chromatography method for the serotonin release assay is equivalent to the radioactive method.

PubMed

Sono-Koree, N K; Crist, R A; Frank, E L; Rodgers, G M; Smock, K J

2016-02-01

The serotonin release assay (SRA) is considered the gold standard laboratory test for heparin-induced thrombocytopenia (HIT). The historic SRA method uses platelets loaded with radiolabeled serotonin to evaluate platelet activation by HIT immune complexes. However, a nonradioactive method is desirable. We report the performance characteristics of a high-performance liquid chromatography (HPLC) SRA method. We validated the performance characteristics of an HPLC-SRA method, including correlation with a reference laboratory using the radioactive method. Serotonin released from reagent platelets was quantified by HPLC using fluorescent detection. Results were expressed as % release and classified as positive, negative, or indeterminate based on previously published cutoffs. Serum samples from 250 subjects with suspected HIT were tested in the HPLC-SRA and with the radioactive method. Concordant classifications were observed in 230 samples (92%). Sera from 41 healthy individuals tested negative. Between-run imprecision studies showed standard deviation of <6 (% release) for positive, weak positive, and negative serum pools. Stability studies demonstrated stability after two freeze-thaw cycles or up to a week of refrigeration. The HPLC-SRA has robust performance characteristics, equivalent to the historic radioactive method, but avoids the complexities of working with radioactivity. © 2015 John Wiley & Sons Ltd.

Latest Sensors and Data Acquisition Development Efforts at KSC

NASA Technical Reports Server (NTRS)

Perotti, Jose M.

2002-01-01

This viewgraph presentation summarizes the characteristics required on sensors by consumers desiring access to space, a long term plan developed at KSC (Kennedy Space Center) to identify promising technologies for NASA's own future sensor needs, and the characteristics of several smart sensors already developed. Also addressed are the computer hardware and architecture used to operate sensors, and generic testing capabilities. Consumers desire sensors which are lightweight, inexpensive, intelligent, and easy to use.

Neural Substrates of Sexual Desire in Individuals with Problematic Hypersexual Behavior

PubMed Central

Seok, Ji-Woo; Sohn, Jin-Hun

2015-01-01

Studies on the characteristics of individuals with hypersexual disorder have been accumulating due to increasing concerns about problematic hypersexual behavior (PHB). Currently, relatively little is known about the underlying behavioral and neural mechanisms of sexual desire. Our study aimed to investigate the neural correlates of sexual desire with event-related functional magnetic resonance imaging (fMRI). Twenty-three individuals with PHB and 22 age-matched healthy controls were scanned while they passively viewed sexual and nonsexual stimuli. The subjects' levels of sexual desire were assessed in response to each sexual stimulus. Relative to controls, individuals with PHB experienced more frequent and enhanced sexual desire during exposure to sexual stimuli. Greater activation was observed in the caudate nucleus, inferior parietal lobe, dorsal anterior cingulate gyrus, thalamus, and dorsolateral prefrontal cortex in the PHB group than in the control group. In addition, the hemodynamic patterns in the activated areas differed between the groups. Consistent with the findings of brain imaging studies of substance and behavior addiction, individuals with the behavioral characteristics of PHB and enhanced desire exhibited altered activation in the prefrontal cortex and subcortical regions. In conclusion, our results will help to characterize the behaviors and associated neural mechanisms of individuals with PHB. PMID:26648855

Induction heating apparatus and methods of operation thereof

DOEpatents

Richardson, John G.

2006-08-01

Methods of operation of an induction melter include providing material within a cooled crucible proximate an inductor. A desired electromagnetic flux skin depth for heating the material within the crucible may be selected, and a frequency of an alternating current for energizing the inductor and for producing the desired skin depth may be selected. The alternating current frequency may be adjusted after energizing the inductor to maintain the desired electromagnetic flux skin depth. The desired skin depth may be substantially maintained as the temperature of the material varies. An induction heating apparatus includes a sensor configured to detect changes in at least one physical characteristic of a material to be heated in a crucible, and a controller configured for selectively varying a frequency of an alternating current for energizing an inductor at least partially in response to changes in the physical characteristic to be detected by the sensor.

Development of mathematical models and optimization of the process parameters of laser surface hardened EN25 steel using elitist non-dominated sorting genetic algorithm

NASA Astrophysics Data System (ADS)

Vignesh, S.; Dinesh Babu, P.; Surya, G.; Dinesh, S.; Marimuthu, P.

2018-02-01

The ultimate goal of all production entities is to select the process parameters that would be of maximum strength, minimum wear and friction. The friction and wear are serious problems in most of the industries which are influenced by the working set of parameters, oxidation characteristics and mechanism involved in formation of wear. The experimental input parameters such as sliding distance, applied load, and temperature are utilized in finding out the optimized solution for achieving the desired output responses such as coefficient of friction, wear rate, and volume loss. The optimization is performed with the help of a novel method, Elitist Non-dominated Sorting Genetic Algorithm (NSGA-II) based on an evolutionary algorithm. The regression equations obtained using Response Surface Methodology (RSM) are used in determining the optimum process parameters. Further, the results achieved through desirability approach in RSM are compared with that of the optimized solution obtained through NSGA-II. The results conclude that proposed evolutionary technique is much effective and faster than the desirability approach.

Reproductive performance and expression of imprinted genes in somatic cell cloned boars.

PubMed

Kawarasaki, Tatsuo; Enya, Satoko; Otake, Masayoshi; Shibata, Masatoshi; Mikawa, Satoshi

2017-11-01

To assess the performance of boars derived by somatic cell cloning, we analyzed various aspects of their reproductive characteristics and the expression of two imprinted genes. Cloned boars (cloned Duroc × Jinhua) were analyzed for birth weight, growth rate, age at first ejaculation, semen characteristics and fertility, in comparison with naturally bred control boars of the same strain. The expression of imprinted genes was analyzed using the microsatellite marker SWC9 for the paternally expressed gene insulin-like growth factor -2 (IGF2) and with single nucleotide polymorphisms (SNPs) for the gene maternally expressed 3 (MEG3). The cloned boars had high production of semen and were nearly equal in level of fertility to conventional pigs; they showed similar characteristics as naturally bred boars of the same strains. The expression of IGF2 was partially disturbed, but this disturbed expression was not linked to a change in developmental fate or reproductive performance. These results indicate that use of cloned boars could be highly effective for proliferation of pigs with desirable characteristics, preservation of genetic resources and risk reduction against epidemic diseases, such as foot-and-mouth disease, through storage of somatic cells as a precautionary measure for use in regenerating pig populations after a future pandemic. © 2017 Japanese Society of Animal Science.

Planetary exploration with electrically propelled vehicles.

NASA Technical Reports Server (NTRS)

Stuhlinger, E.

1972-01-01

The characteristics of propulsion systems required for carrying out flight missions within the solar system, as desired by planetary physicists and astronomers, are reviewed. It is shown that an encouraging answer to these requirements is available in the form of electrostatic or ion propulsion systems. The design and performance characteristics of an electrostatic thrustor employing an ion source, accelerating electrode, beam neutralizer, and power source are discussed, together with those of the Kaufmann engine (electrostatic thrustor employing bombardment type ionization). More demanding missions which will become feasible with the advent of nuclear-electric power sources (such as the incore thermionic reactor) may include close orbiters around all the planets, and asteroid and cometary missions.

Piloted Simulation Investigation of a Supersonic Transport Configuration (LaRC.4)

NASA Technical Reports Server (NTRS)

Jackson, E. Bruce; Martinez, Debbie; Derry, Stephen D.

1999-01-01

This report contains a description of the test facilities and software utilized during a joint NASA/aerospace industry study of improved control laws and desired inceptor characteristics for a candidate supersonic transport air-craft design. Details concerning the characteristics of the simulation cockpit, image generator and display systems, and motion platform are described. Depictions of the various display formats are included. The test schedule, session log, and flight cards describing the maneuvers performed is included. A brief summary of high-lights of the study is given. Modifications made to the industry-provided simulation model are described. This report is intended to serve as a reference document for industry researchers.

Flight evaluations of several hover control and display combinations for precise blind vertical landings

NASA Technical Reports Server (NTRS)

Schroeder, J. A.; Merrick, V. K.

1990-01-01

Several control and display concepts were evaluated on a variable-stability helicopter prior to future evaluations on a modified Harrier. The control and display concepts had been developed to enable precise hover maneuvers, station keeping, and vertical landings in simulated zero-visibility conditions and had been evaluated extensively in previous piloted simulations. Flight evaluations early in the program revealed several inadequacies in the display drive laws that were later corrected using an alternative design approach that integrated the control and display characteristics with the desired guidance law. While hooded, three pilots performed landing-pad captures followed by vertical landings with attitude-rate, attitude, and translation-velocity-command control systems. The latter control system incorporated a modified version of state-rate-feedback implicit-model following. Precise landing within 2 ft of the desired touchdown point were achieved.

Characterization of a piezoelectric valve for an adaptive pneumatic shock absorber

NASA Astrophysics Data System (ADS)

Mikułowski, Grzegorz; Wiszowaty, Rafał; Holnicki-Szulc, Jan

2013-12-01

This paper describes a pneumatic valve based on a multilayer piezoelectric actuator and Hörbiger plates. The device was designed to operate in an adaptive pneumatic shock absorber. The adaptive pneumatic shock absorber was considered as a piston-cylinder device and the valve was intended to be installed inside the piston. The main objective for the valve application was regulating the gas flow between the cylinder’s chambers in order to maintain the desired value of the reaction force generated by the shock absorber. The paper describes the design constraints and requirements, together with results of analytical modelling of fluid flow verified versus experimentally obtained data. The presented results indicate that the desired performance characteristics of the valve were obtained. The geometrical constraints of the flow ducts were studied and the actuator’s functional features analysed.

Drag king magic: performing/becoming the other.

PubMed

Rosenfeld, Kathryn

2002-01-01

This chapter seeks to theorize drag king practice through the lenses of alterity, liminality, and performance theory, while attempting to complicate and reinvigorate discussions of identity raised by drag. I examine the ways in which drag king performance plumbs the concept of "the Other," and forces confrontation with a complex field of desire. Contemporary "queergirl" existence negotiates a range of desirable and desiring Others, from the polarities (i.e., butch-femme) unique to queer structures of desire, to the desire of those on the cultural margins for the power of those at the center, and vice versa. I employ anthropological theories of performance, mimesis, and liminality to establish a framework through which drag kings may be viewed as crucibles of this desire and agents of this power exchange. By performing maleness, drag kings expand and redraw the definitional boundaries of the male, interfere with the cultural power of mainstream maleness, and simultaneously transfer some of this power to themselves as queer women. At the same time, drag king existence forces a renegotiation of queergirl desire to encompass a range of masculinities. By performing/becoming the Other, drag kings engage in a practice of magic which transforms both margin and center.

Multi-criteria decision making development of ion chromatographic method for determination of inorganic anions in oilfield waters based on artificial neural networks retention model.

PubMed

Stefanović, Stefica Cerjan; Bolanča, Tomislav; Luša, Melita; Ukić, Sime; Rogošić, Marko

2012-02-24

This paper describes the development of ad hoc methodology for determination of inorganic anions in oilfield water, since their composition often significantly differs from the average (concentration of components and/or matrix). Therefore, fast and reliable method development has to be performed in order to ensure the monitoring of desired properties under new conditions. The method development was based on computer assisted multi-criteria decision making strategy. The used criteria were: maximal value of objective functions used, maximal robustness of the separation method, minimal analysis time, and maximal retention distance between two nearest components. Artificial neural networks were used for modeling of anion retention. The reliability of developed method was extensively tested by the validation of performance characteristics. Based on validation results, the developed method shows satisfactory performance characteristics, proving the successful application of computer assisted methodology in the described case study. Copyright © 2011 Elsevier B.V. All rights reserved.

Grafting for control of meloidogyne spp. in fruiting vegetables

USDA-ARS?s Scientific Manuscript database

Regulatory restraints on the use of soil fumigants have increased the need for sustainable nematode management approaches. Nematode resistant vegetable varieties with desirable horticultural characteristics are limited. Technology enabling the grafting of desirable scion varieties onto resistant ro...

Pattern Recognition Control Design

NASA Technical Reports Server (NTRS)

Gambone, Elisabeth A.

2018-01-01

Spacecraft control algorithms must know the expected vehicle response to any command to the available control effectors, such as reaction thrusters or torque devices. Spacecraft control system design approaches have traditionally relied on the estimated vehicle mass properties to determine the desired force and moment, as well as knowledge of the effector performance to efficiently control the spacecraft. A pattern recognition approach was used to investigate the relationship between the control effector commands and spacecraft responses. Instead of supplying the approximated vehicle properties and the thruster performance characteristics, a database of information relating the thruster ring commands and the desired vehicle response was used for closed-loop control. A Monte Carlo simulation data set of the spacecraft dynamic response to effector commands was analyzed to establish the influence a command has on the behavior of the spacecraft. A tool developed at NASA Johnson Space Center to analyze flight dynamics Monte Carlo data sets through pattern recognition methods was used to perform this analysis. Once a comprehensive data set relating spacecraft responses with commands was established, it was used in place of traditional control methods and gains set. This pattern recognition approach was compared with traditional control algorithms to determine the potential benefits and uses.

Silicon micromachined vibrating gyroscopes

NASA Astrophysics Data System (ADS)

Voss, Ralf

1997-09-01

This work gives an overview of silicon micromachined vibrating gyroscopes. Market perspectives and fields of application are pointed out. The advantage of using silicon micromachining is discussed and estimations of the desired performance, especially for automobiles are given. The general principle of vibrating gyroscopes is explained. Vibrating silicon gyroscopes can be divided into seven classes. for each class the characteristic principle is presented and examples are given. Finally a specific sensor, based on a tuning fork for automotive applications with a sensitivity of 250(mu) V/degrees is described in detail.

Efficiency and Pressure Loss Characteristics of an Ultra-Compact Combustor with Bulk Swirl

DTIC Science & Technology

2007-06-01

al., 2004a:3). Besides offering size and weight reductions, the UCC opens the door to adding a reheat step to the Brayton cycle currently used in...possible include a reheat step in the Brayton cycle to gain enhanced performance. Sirignano and Liu (Sirignano and Liu, 1998:1-2) pioneered the idea of...increase in speed for a subsonic flow resulting in a given loss in total pressure. This pressure loss is not desired in the constant pressure Brayton

A Feasibility Study on the Control of a Generic Air Vehicle Using Control Moment Gyros

NASA Technical Reports Server (NTRS)

Lim, Kyong B.; Moerder, Daniel D.

2006-01-01

This paper examines feasibility and performance issues in using Control Moment Gyroscopes (CMGs) to control the attitude of a fixed-wing aircraft. The paper describes a control system structure that permits allocating control authority and bandwidth between a CMG system and conventional aerodynamic control surfaces to stabilize a vehicle with neutral aerodynamic stability. A simulation study explores the interplay between aerodynamic and CMG effects, and indicates desirable physical characteristics for a CMG system to be used for aircraft attitude control.

Grumman electric truck development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kessler, J.C.; Ferdman, S.

1981-11-01

An electric truck development was undertaken to prepare for the markets of the 1980's. Grumman is using its aluminum truck bodies technology to create a light weight vehicle. A redesigned unitized, all aluminum body and a new propulsion system resulted in the desired vehicle. The vehicle meets the requirements of the US Postal Service and the DOE Demonstration program. The unitized chassisless structure is designed to take major driving loads. Design features and performance characteristics are enumerated. Safety and service considerations have been incorporated into the vehicle.

Controller partitioning for integrated flight/propulsion control implementation

NASA Technical Reports Server (NTRS)

Garg, Sanjay

1993-01-01

The notion of partitioning a centralized controller into a decentralized, hierarchical structure suitable for integrated flight/propulsion control (IFPC) implementation is discussed. A systematic procedure is developed for determining partitioned airframe and engine subsystem controllers (subcontrollers), with the desired interconnection structure, that approximate the closed-loop performance and robustness characteristics of a given centralized controller. The procedure is demonstrated by application to IFPC design for a Short Take-Off and Vertical Landing (STOVL) aircraft in the landing approach to hover transition flight phase.

Partitioning of centralized integrated flight/propulsion control design for decentralized implementation

NASA Technical Reports Server (NTRS)

Garg, Sanjay

1993-01-01

The notion of partitioning a centralized controller into a decentralized, hierarchical structure suitable for integrated flight/propulsion control (IFPC) implementation is discussed. A systematic procedure is developed for determining partitioned airframe and engine subsystem controllers (subcontrollers), with the desired interconnection structure, that approximate the closed-loop performance and robustness characteristics of a given centralized controller. The procedure is demonstrated by application to IFPC design for a short take-off and vertical landing (STOVL) aircraft in the landing-approach-to-hover-transition flight phase.

Micromotors with Step-Motor Characteristics by Controlled Magnetic Interactions among Assembled Components

PubMed Central

2015-01-01

In this study, we investigated the control of the rotation dynamics of an innovative type of rotary micromotors with desired performances by tuning the magnetic interactions among the assembled micro/nanoscale components. The micromotors are made of metallic nanowires as rotors, patterned magnetic nanodisks as bearings and actuated by external electric fields. The magnetic forces for anchoring the rotors on the bearings play an essential role in the rotation dynamics of the micromotors. By varying the moment, orientation, and dimension of the magnetic components, distinct rotation behaviors can be observed, including repeatable wobbling and rolling in addition to rotation. We understood the rotation behaviors by analytical modeling, designed and realized micromotors with step-motor characteristics. The outcome of this research could inspire the development of high-performance nanomachines assembled from synthetic nanoentities, relevant to nanorobotics, microfluidics, and biomedical research. PMID:25536023

Investigation of High-alpha Lateral-directional Control Power Requirements for High-performance Aircraft

NASA Technical Reports Server (NTRS)

Foster, John V.; Ross, Holly M.; Ashley, Patrick A.

1993-01-01

Designers of the next-generation fighter and attack airplanes are faced with the requirements of good high-angle-of-attack maneuverability as well as efficient high speed cruise capability with low radar cross section (RCS) characteristics. As a result, they are challenged with the task of making critical design trades to achieve the desired levels of maneuverability and performance. This task has highlighted the need for comprehensive, flight-validated lateral-directional control power design guidelines for high angles of attack. A joint NASA/U.S. Navy study has been initiated to address this need and to investigate the complex flight dynamics characteristics and controls requirements for high-angle-of-attack lateral-directional maneuvering. A multi-year research program is underway which includes ground-based piloted simulation and flight validation. This paper will give a status update of this program that will include a program overview, description of test methodology and preliminary results.

Investigation of high-alpha lateral-directional control power requirements for high-performance aircraft

NASA Technical Reports Server (NTRS)

Foster, John V.; Ross, Holly M.; Ashley, Patrick A.

1993-01-01

Designers of the next-generation fighter and attack airplanes are faced with the requirements of good high angle-of-attack maneuverability as well as efficient high speed cruise capability with low radar cross section (RCS) characteristics. As a result, they are challenged with the task of making critical design trades to achieve the desired levels of maneuverability and performance. This task has highlighted the need for comprehensive, flight-validated lateral-directional control power design guidelines for high angles of attack. A joint NASA/U.S. Navy study has been initiated to address this need and to investigate the complex flight dynamics characteristics and controls requirements for high angle-of-attack lateral-directional maneuvering. A multi-year research program is underway which includes groundbased piloted simulation and flight validation. This paper will give a status update of this program that will include a program overview, description of test methodology and preliminary results.

Drive Control Scheme of Electric Power Assisted Wheelchair Based on Neural Network Learning of Human Wheelchair Operation Characteristics

NASA Astrophysics Data System (ADS)

Tanohata, Naoki; Seki, Hirokazu

This paper describes a novel drive control scheme of electric power assisted wheelchairs based on neural network learning of human wheelchair operation characteristics. “Electric power assisted wheelchair” which enhances the drive force of the operator by employing electric motors is expected to be widely used as a mobility support system for elderly and disabled people. However, some handicapped people with paralysis of the muscles of one side of the body cannot maneuver the wheelchair as desired because of the difference in the right and left input force. Therefore, this study proposes a neural network learning system of such human wheelchair operation characteristics and a drive control scheme with variable distribution and assistance ratios. Some driving experiments will be performed to confirm the effectiveness of the proposed control system.

Effect of Applied Current Density on Cavitation-Erosion Characteristics for Anodized Al Alloy.

PubMed

Lee, Seung-Jun; Kim, Seong-Jong

2018-02-01

Surface finishing is as important as selection of material to achieve durability. Surface finishing is a process to provide surface with the desired performance and features by applying external forces such as thermal energy or stress. This study investigated the optimum supply current density for preventing from cavitation damages by applying to an anodizing technique that artificially forms on the surface an oxide coating that has excellent mechanical characteristics, such as hardness, wear resistance. Result of hardness test, the greater hardness was associated with greater brittleness, resulting in deleterious characteristics. Consequently, under conditions such as the electrolyte concentration of 10 vol.%, the processing time of 40 min, the electrolyte temperature of 10 °C, and the current density of 20 mA/cm2 were considered to be the optimum anodizing conditions for improvement of durability in seawater.

Grindability measurements on low-rank fuels. [Prediction of large pulverizer performance from small scale test equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peipho, R.R.; Dougan, D.R.

1981-01-01

Experience has shown that the grinding characteristics of low rank coals are best determined by testing them in a pulverizer. Test results from a small MPS-32 Babcock and Wilcox pulverizer to predict large, full-scale pulverizer performance are presented. The MPS-32 apparatus, test procedure and evaluation of test results is described. The test data show that the Hardgrove apparatus and the ASTM test method must be used with great caution when considering low-rank fuels. The MPS-32 meets the needs for real-machine simulation but with some disadvantages. A smaller pulverizer is desirable. 1 ref.

A configuration development strategy for the NASP

NASA Astrophysics Data System (ADS)

Snyder, Curtis D.; Pinckney, S. Z.

Characteristics of airframe-integrated scramjet (AIS) aerospacecraft are studied using elementary and a recently developed AIS analysis code. Of principal interest is the definition of the AIS and what concepts offer the most potential. One of the concepts is selected for a limited optimization study aimed at defining the relationship of exhaust area to performance potential. The study shows that, if the AIS vehicle is to be fully constrained within the 'optimum' flowpath envelope, large values of exhaust-area-to-capture-area ratio are desired. A benefit of this choice is that performance at the very highest airbreather speeds is improved and, thus, may delay the need to switch to rocket power.

A new broadband square law detector. [microwave radiometers

NASA Technical Reports Server (NTRS)

Reid, M. S.; Gardner, R. A.; Stelzried, C. T.

1975-01-01

A broadband constant law detector was developed for precision power measurements, radio metric measurements, and other applications. It has a wide dynamic range and an accurate square law response. Other desirable characteristics, which are all included in a single compact unit, are: (1) high-level dc output with immunity to ground loop problems; (2) fast response times; (3) ability to insert known time constants; and (4) good thermal stability. The detector and its performance are described in detail. The detector can be operated in a programmable system with a ten-fold increase in accuracy. The use and performance of the detector in a noise-adding radiometer system is also discussed.

Performance Characteristics of a Cross-Flow Hydrokinetic Turbine under Unsteady Conditions

NASA Astrophysics Data System (ADS)

Flack, Karen; Lust, Ethan; Bailin, Ben

2017-11-01

Performance characteristics are presented for a cross-flow hydrokinetic turbine designed for use in a riverine environment. The test turbine is a 1:6 scale model of a three-bladed device (9.5 m span, 6.5 m diameter) that has been proposed by the Department of Energy. Experiments are conducted in the large towing tank (116 m long, 7.9 m wide, 5 m deep) at the United States Naval Academy. The turbine is towed beneath a moving carriage at a constant speed in combination with a shaft motor to achieve the desired tip speed ratio (TSR) range. The measured quantities of turbine thrust, torque and RPM result in power and thrust coefficients for a range of TSR. Results will be presented for cases with quiescent flow at a range of Reynolds numbers and flow with mild surface waves, representative of riverine environments. The impact of unsteady flow conditions on the average turbine performance was not significant. Unsteady flow conditions did have an impact on instantaneous turbine performance which operationally would result in unsteady blade loading and instantaneous power quality.

Application of controller partitioning optimization procedure to integrated flight/propulsion control design for a STOVL aircraft

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Schmidt, Phillip H.

1993-01-01

A parameter optimization framework has earlier been developed to solve the problem of partitioning a centralized controller into a decentralized, hierarchical structure suitable for integrated flight/propulsion control implementation. This paper presents results from the application of the controller partitioning optimization procedure to IFPC design for a Short Take-Off and Vertical Landing (STOVL) aircraft in transition flight. The controller partitioning problem and the parameter optimization algorithm are briefly described. Insight is provided into choosing various 'user' selected parameters in the optimization cost function such that the resulting optimized subcontrollers will meet the characteristics of the centralized controller that are crucial to achieving the desired closed-loop performance and robustness, while maintaining the desired subcontroller structure constraints that are crucial for IFPC implementation. The optimization procedure is shown to improve upon the initial partitioned subcontrollers and lead to performance comparable to that achieved with the centralized controller. This application also provides insight into the issues that should be addressed at the centralized control design level in order to obtain implementable partitioned subcontrollers.

Design of set-point weighting PIλ + Dμ controller for vertical magnetic flux controller in Damavand tokamak.

PubMed

Rasouli, H; Fatehi, A

2014-12-01

In this paper, a simple method is presented for tuning weighted PI(λ) + D(μ) controller parameters based on the pole placement controller of pseudo-second-order fractional systems. One of the advantages of this controller is capability of reducing the disturbance effects and improving response to input, simultaneously. In the following sections, the performance of this controller is evaluated experimentally to control the vertical magnetic flux in Damavand tokamak. For this work, at first a fractional order model is identified using output-error technique in time domain. For various practical experiments, having desired time responses for magnetic flux in Damavand tokamak, is vital. To approach this, at first the desired closed loop reference models are obtained based on generalized characteristic ratio assignment method in fractional order systems. After that, for the identified model, a set-point weighting PI(λ) + D(μ) controller is designed and simulated. Finally, this controller is implemented on digital signal processor control system of the plant to fast/slow control of magnetic flux. The practical results show appropriate performance of this controller.

Implementation of a Trailing-Edge Flap Analysis Model in the NASA Langley CAMRAD.MOD1/Hires Program

NASA Technical Reports Server (NTRS)

Charles, Bruce

1999-01-01

Continual advances in rotorcraft performance, vibration and acoustic characteristics are being sought by rotary-wing vehicle manufacturers to improve efficiency, handling qualities and community noise acceptance of their products. The rotor system aerodynamic and dynamic behavior are among the key factors which must be addressed to meet the desired goals. Rotor aerodynamicists study how airload redistribution impacts performance and noise, and seek ways to achieve better airload distribution through changes in local aerodynamic response characteristics. One method currently receiving attention is the use of trailing-edge flaps mounted on the rotor blades to provide direct control of a portion of the spanwise lift characteristics. The following work describes the incorporation of a trailing-edge flap model in the CAMRAD.Mod1/FHUS comprehensive rotorcraft analysis code. The CAM-RAD.Mod1/HIRES analysis consists of three separate executable codes. These include the comprehensive trim analysis, CAMRAD.Mod1, the Indicial Post-Processor, IPP, for high resolution airloads, and AIRFOIL, which produces the rotor airfoil tables from input airfoil section characteristics. The modifications made to these components permitting analysis of flapped rotor configurations are documented herein along with user instructions detailing the new input variables and operational notes.

Performance Evaluation and Parameter Identification on DROID III

NASA Technical Reports Server (NTRS)

Plumb, Julianna J.

2011-01-01

The DROID III project consisted of two main parts. The former, performance evaluation, focused on the performance characteristics of the aircraft such as lift to drag ratio, thrust required for level flight, and rate of climb. The latter, parameter identification, focused on finding the aerodynamic coefficients for the aircraft using a system that creates a mathematical model to match the flight data of doublet maneuvers and the aircraft s response. Both portions of the project called for flight testing and that data is now available on account of this project. The conclusion of the project is that the performance evaluation data is well-within desired standards but could be improved with a thrust model, and that parameter identification is still in need of more data processing but seems to produce reasonable results thus far.

Understanding Treatment Readiness in Recently Assessed, Pre-Treatment Substance Abusers

PubMed Central

Rapp, Richard C.; Xu, Jiangmin; Carr, Carey A.; Timothy Lane, D.; Redko, Cristina; Wang, Jichuan; Carlson, Robert G.

2007-01-01

The goal of this study was to more fully understand readiness for treatment in a pre-treatment sample of 446 substance abusers. Structural Equation Modeling (SEM) was used to: (1) examine the relationships between readiness factors identified in the Pre-Treatment Readiness Scale; and (2) identify the effects of predisposing, illness, and inhibiting determinants on the factors. As with in-treatment samples, Problem Recognition was found to influence Treatment Readiness, although through a different intervening factor, Desire for Change rather than Desire for Help. A fourth factor, Treatment Reluctance, was also influenced by the Desire for Change factor. Fixed characteristics such as age and gender had minimal influences on readiness factors, as did inhibiting characteristics that reflected recent functioning. Illness characteristics including drug severity and perceived treatment barriers had a more robust influence on readiness factors. This study provides an increased understanding of readiness for treatment among pre-treatment substance abusers and also supported the construct validity of the Pre-Treatment Readiness Scale. PMID:19274847

Personality based clusters as predictors of aviator attitudes and performance

NASA Technical Reports Server (NTRS)

Gregorich, Steve; Helmreich, Robert L.; Wilhelm, John A.; Chidester, Thomas

1989-01-01

The feasibility of identification of personality-based population clusters was investigated along with the relationships of these subpopulations to relevant attitude and performance measures. The results of instrumental and expressive personality tests, using the Personal Characteristics Inventory (PCI) test battery and the Cockpit Management Attitudes Questionnaire, suggest that theoretically meaningful subpopulations exist among aviators, and that these groupings are useful in understanding of personality factors acting as moderator variables in the determination of aviator attitudes and performance. Out of the three clusters most easily described in terms of their relative elevations on the PCI subscales ('the right stuff', the 'wrong stuff', and the 'no stuff'), the members of the right stuff cluster tended to have more desirable patterns of responses along relevant attitudinal dimensions.

Multicriteria Gain Tuning for Rotorcraft Flight Controls (also entitled The Development of the Conduit Advanced Control System Design and Evaluation Interface with a Case Study Application Fly by Wire Helicopter Design)

NASA Technical Reports Server (NTRS)

Biezad, Daniel

1997-01-01

Handling qualities analysis and control law design would seem to be naturally complimenting components of aircraft flight control system design, however these two closely coupled disciplines are often not well integrated in practice. Handling qualities engineers and control system engineers may work in separate groups within an aircraft company. Flight control system engineers and handling quality specialists may come from different backgrounds and schooling and are often not aware of the other group's research. Thus while the handling qualities specifications represent desired aircraft response characteristics, these are rarely incorporated directly in the control system design process. Instead modem control system design techniques are based on servo-loop robustness specifications, and simple representations of the desired control response. Comprehensive handling qualities analysis is often left until the end of the design cycle and performed as a check of the completed design for satisfactory performance. This can lead to costly redesign or less than satisfactory aircraft handling qualities when the flight testing phase is reached. The desire to integrate the fields of handling qualities and flight,control systems led to the development of the CONDUIT system. This tool facilitates control system designs that achieve desired handling quality requirements and servo-loop specifications in a single design process. With CONDUIT, the control system engineer is now able to directly design and control systems to meet the complete handling specifications. CONDUIT allows the designer to retain a preferred control law structure, but then tunes the system parameters to meet the handling quality requirements.

Novel method to control antenna currents based on theory of characteristic modes

NASA Astrophysics Data System (ADS)

Elghannai, Ezdeen Ahmed

Characteristic Mode Theory is one of the very few numerical methods that provide a great deal of physical insight because it allows us to determine the natural modes of the radiating structure. The key feature of these modes is that the total induced antenna current, input impedance/admittance and radiation pattern can be expressed as a linear weighted combination of individual modes. Using this decomposition method, it is possible to study the behavior of the individual modes, understand them and therefore control the antennas behavior; in other words, control the currents induced on the antenna structure. This dissertation advances the topic of antenna design by carefully controlling the antenna currents over the desired frequency band to achieve the desired performance specifications for a set of constraints. Here, a systematic method based on the Theory of Characteristic Modes (CM) and lumped reactive loading to achieve the goal of current control is developed. The lumped reactive loads are determined based on the desired behavior of the antenna currents. This technique can also be used to impedance match the antenna to the source/generator connected to it. The technique is much more general than the traditional impedance matching. Generally, the reactive loads that properly control the currents exhibit a combination of Foster and non-Foster behavior. The former can be implemented with lumped passive reactive components, while the latter can be implemented with lumped non-Foster circuits (NFC). The concept of current control is applied to design antennas with a wide band (impedance/pattern) behavior using reactive loads. We successfully applied this novel technique to design multi band and wide band antennas for wireless applications. The technique was developed to match the antenna to resistive and/or complex source impedance and control the radiation pattern at these frequency bands, considering size and volume constraints. A wide band patch antenna was achieved using the developed technique. In addition, the technique was applied to multi band wire less Universal Serial Bus (USB) dongle antenna that serves for WLAN IEEE 802.11 a/b/g/n band applications and Radio Frequency Identification (RFID) tag antenna for 915MHz band applications with superior performance compared to previous published results. This dissertation also discusses the total Q of an antenna from the CM standpoint. A new expression as well as additional physical information about each mode's individual contribution to the total antenna Q are provided. Finally, the theory is used to an analyze the antenna in both radiation and/or scattering modes. In the antenna scattering mode, the field scattered by an antenna contains a component that is the short circuit scattered field, and a second component that is proportional to the radiation field. In this dissertation, an analytical study of this phenomena from the CM standpoint is performed aiming to shed some light on antenna scattering phenomenon where additional physical insight is obtained and thus used to reach desire results.

Hypersexuality and high sexual desire: exploring the structure of problematic sexuality.

PubMed

Carvalho, Joana; Štulhofer, Aleksandar; Vieira, Armando L; Jurin, Tanja

2015-06-01

The concept of hypersexuality has been accompanied by fierce debates and conflicting conclusions about its nature. One of the central questions under the discussion is a potential overlap between hypersexuality and high sexual desire. With the relevant research in its early phase, the structure of hypersexuality remains largely unknown. The aim of the present study was to systematically explore the overlap between problematic sexuality and high sexual desire. A community online survey was carried out in Croatia in 2014. The data were first cluster analyzed (by gender) based on sexual desire, sexual activity, perceived lack of control over one's sexuality, and negative behavioral consequences. Participants in the meaningful clusters were then compared for psychosocial characteristics. To complement cluster analysis (CA), multigroup confirmatory factor analysis (CFA) of the same four constructs was carried out. Indicators representing the proposed structure of hypersexuality were included: sexual desire, frequency of sexual activity, lack of control over one's sexuality, and negative behavioral outcomes. Psychosocial characteristics such as religiosity, attitudes toward pornography, and general psychopathology were also evaluated. CA pointed to the existence of two meaningful clusters, one representing problematic sexuality, that is, lack of control over one's sexuality and negative outcomes (control/consequences cluster), and the other reflecting high sexual desire and frequent sexual activity (desire/activity cluster). Compared with the desire/activity cluster, individuals from the control/consequences cluster reported more psychopathology and were characterized by more traditional attitudes. Complementing the CA findings, CFA pointed to two distinct latent dimensions-problematic sexuality and high sexual desire/activity. Our study supports the distinctiveness of hypersexuality and high sexual desire/activity, suggesting that problematic sexuality might be more associated with the perceived lack of personal control over sexuality and moralistic attitudes than with high levels of sexual desire and activity. © 2015 International Society for Sexual Medicine.

Experimental study at low supersonic speeds of a missile concept having opposing wraparound tails

NASA Technical Reports Server (NTRS)

Allen, Jerry M.; Watson, Carolyn B.

1994-01-01

A wind-tunnel investigation has been performed at low supersonic speeds (at Mach numbers of 1.60, and 2.16) to evaluate the aerodynamic characteristics of a missile concept capable of being tube launched and controlled with a simple one-axis canard controller. This concept, which features an axisymmetric body with two planar canards and four wraparound tail fins arranged in opposing pairs, must be in rolling motion to be controllable in any radial plane with the planar canards. Thus, producing a constant rolling moment that is invariant with speed and attitude to provide the motion is desirable. Two tail-fin shaping designs, one shaved and one beveled, were evaluated for their efficiency in producing the needed rolling moments, and the results showed that the shaved fins were much more desirable for this task than the beveled fins.

Series Elastic Actuators for legged robots

NASA Astrophysics Data System (ADS)

Pratt, Jerry E.; Krupp, Benjamin T.

2004-09-01

Series Elastic Actuators provide many benefits in force control of robots in unconstrained environments. These benefits include high force fidelity, extremely low impedance, low friction, and good force control bandwidth. Series Elastic Actuators employ a novel mechanical design architecture which goes against the common machine design principal of "stiffer is better." A compliant element is placed between the gear train and driven load to intentionally reduce the stiffness of the actuator. A position sensor measures the deflection, and the force output is accurately calculated using Hooke"s Law (F=Kx). A control loop then servos the actuator to the desired output force. The resulting actuator has inherent shock tolerance, high force fidelity and extremely low impedance. These characteristics are desirable in many applications including legged robots, exoskeletons for human performance amplification, robotic arms, haptic interfaces, and adaptive suspensions. We describe several variations of Series Elastic Actuators that have been developed using both electric and hydraulic components.

Flight Studies of Problems Pertinent to High-Speed Operation of Jet Transports

NASA Technical Reports Server (NTRS)

Butchart, Stanley P.; Fischel, Jack; Tremant, Robert A.; Robinson, Glenn H.

1959-01-01

A flight investigation was made to assess the potential operational problems of jet transports in the transonic cruise range. In this study a large multiengine jet airplane having geometric characteristics fairly representative of the jet transport was used; however, in order to ensure general applicability of the results, the aerodynamic characteristics of the test airplane were varied to simulate a variety of jet- transport airplanes. Some of the specific areas investigated include: (1) an overall evaluation of longitudinal stability and control characteristics at transonic speeds, with an assessment of pitch-up characteristics, (2) the effect of buffeting on airplane operational speeds and maneuvering, (3) the desirable lateral-directional damping characteristics, (4) the desirable lateral-control characteristics, (5) an assessment of over-speed and speed-spread requirements, including the upset maneuver, and (6) an assessment of techniques and airplane characteristics for rapid descent and slow-down. The results presented include pilots' evaluation of the various problem areas and specific recommendations for possible improvement of jet-transport operations in the cruising speed range.

Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications.

PubMed

Marín-Sáez, Julia; Atencia, Jesús; Chemisana, Daniel; Collados, María-Victoria

2016-03-21

Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range.

Outcomes Desired by Practitioners and Academics.

ERIC Educational Resources Information Center

Neff, Bonita Dostal; Walker, Gael; Smith, Michael F.; Creedon, Pam J.

1999-01-01

Uses data from the national survey described elsewhere in this issue to develop profiles of the desired characteristics of entry-level and advanced-level practitioners, and for educators teaching public relations in undergraduate and graduate programs. Finds unexpectedly strong agreement between educators and practitioners regarding these issues,…

Women's hair as a cue to desired relationship and parenting characteristics.

PubMed

Matz, David C; Hinsz, Verlin B

2017-10-30

We investigated how women's hair color (blond, brown, black) and length (short, medium, long) influences males' judgments about the women's age, health, physical attractiveness, relationship potential, and parenting capability. Results, which are generally consistent with evolutionary psychology approaches, indicate that hair color and, to a lesser extent, length can affect perceptions of personal characteristics. More specifically, we found that lighter hair (blond and brown) compared to darker hair (black) is generally associated with perceptions of youth, health and attractiveness, and generally leads to more positive perceptions of relationship and parenting potential. Furthermore, the relationships between variables suggest that characteristics directly related to reproductive potential may be inferred from more obvious indirect characteristics. These results suggest that males are able to make complex judgments about women concerning their desirable relationship and parenting potential based on discernable characteristics such as hair color and length.

Positioning actuators in efficient locations for rendering the desired sound field using inverse approach

NASA Astrophysics Data System (ADS)

Cho, Wan-Ho; Ih, Jeong-Guon; Toi, Takeshi

2015-12-01

For rendering a desired characteristics of a sound field, a proper conditioning of acoustic actuators in an array are required, but the source condition depends strongly on its position. Actuators located at inefficient positions for control would consume the input power too much or become too much sensitive to disturbing noise. These actuators can be considered redundant, which should be sorted out as far as such elimination does not damage the whole control performance significantly. It is known that the inverse approach based on the acoustical holography concept, employing the transfer matrix between sources and field points as core element, is useful for rendering the desired sound field. By investigating the information indwelling in the transfer matrix between actuators and field points, the linear independency of an actuator from the others in the array can be evaluated. To this end, the square of the right singular vector, which means the radiation contribution from the source, can be used as an indicator. Inefficient position for fulfilling the desired sound field can be determined as one having smallest indicator value among all possible actuator positions. The elimination process continues one by one, or group by group, until the remaining number of actuators meets the preset number. Control examples of exterior and interior spaces are taken for the validation. The results reveal that the present method for choosing least dependent actuators, for a given number of actuators and field condition, is quite effective in realizing the desired sound field with a noisy input condition, and in minimizing the required input power.

A Study on Characteristics and Competencies Needed by Teachers of the Mentally Retarded.

ERIC Educational Resources Information Center

Ho, Hua-Kuo

This study assessed the characteristics of 134 teachers of the mentally retarded in Taiwan, and surveyed 321 teachers of the retarded concerning desirable teacher characteristics and competencies. Four main conclusions were drawn: (1) outstanding teachers of the retarded were highly rated for such characteristics as "flexibility of…

36 CFR 219.7 - New plan development or plan revision.

Code of Federal Regulations, 2013 CFR

2013-07-01

... importance of various physical, biological, social, cultural, and historic resources on the plan area (§ 219... desired condition is a description of specific social, economic, and/or ecological characteristics of the... intent, other than desired conditions, usually related to process or interaction with the public. Goals...

36 CFR 219.7 - New plan development or plan revision.

Code of Federal Regulations, 2014 CFR

2014-07-01

... importance of various physical, biological, social, cultural, and historic resources on the plan area (§ 219... desired condition is a description of specific social, economic, and/or ecological characteristics of the... intent, other than desired conditions, usually related to process or interaction with the public. Goals...

36 CFR 219.7 - New plan development or plan revision.

Code of Federal Regulations, 2012 CFR

2012-07-01

... importance of various physical, biological, social, cultural, and historic resources on the plan area (§ 219... desired condition is a description of specific social, economic, and/or ecological characteristics of the... intent, other than desired conditions, usually related to process or interaction with the public. Goals...

The Marlowe-Crowne and Edwards Social Desirability Scales: A Psychometric Perspective.

ERIC Educational Resources Information Center

O'Grady, Kevin E.

1988-01-01

Various psychometric characteristics of the Marlowe-Crowne and Edwards Social Desirability scales were assessed in a sample of 108 male and 189 female undergraduates. Results suggest that males and females show different means and similar internal consistency reliability and intercorrelation on the two scales. (TJH)

Pilot-model analysis and simulation study of effect of control task desired control response

NASA Technical Reports Server (NTRS)

Adams, J. J.; Gera, J.; Jaudon, J. B.

1978-01-01

A pilot model analysis was performed that relates pilot control compensation, pilot aircraft system response, and aircraft response characteristics for longitudinal control. The results show that a higher aircraft short period frequency is required to achieve superior pilot aircraft system response in an altitude control task than is required in an attitude control task. These results were confirmed by a simulation study of target tracking. It was concluded that the pilot model analysis provides a theoretical basis for determining the effect of control task on pilot opinions.

Ternary binder based plasters with improved thermal insulating ability

NASA Astrophysics Data System (ADS)

Čáchová, M.; Koňáková, D.; Vejmelková, E.; Vyšvařil, M.

2017-10-01

New kind of plasters with improved thermal insulating ability are presented in this article. Improvement was reached by utilization of lightweight expanded perlite with high porosity. The second used aggregate was silica sand. Regarding the binder, three kind were combined for the reason of better plaster performance. Pure lime, Portland cement and pozzolanic ceramic powder were employed. Basic physical properties and thermal characteristics were determined. The porosity of plasters reached desired higher value about 50% and the thermal conductivity in dry state was lower than 0.16 Wm-1K-1.

Vehicle wheel drag coefficient in relation to travelling velocity - CFD analysis

NASA Astrophysics Data System (ADS)

Leśniewicz, P.; Kulak, M.; Karczewski, M.

2016-10-01

In order to understand the aerodynamic losses associated with a rotating automobile wheel, a detailed characteristics of the drag coefficient in relation to the applied velocity are necessary. Single drag coefficient value is most often reported for the commercially available vehicles, much less is revealed about the influence of particular car components on the energy consumption in various driving cycles. However, detailed flow potential losses determination is desired for performance estimation. To address these needs, the numerical investigation of an isolated wheel is proposed herein.

Optimization and guidance of flight trajectories for the national aerospace plane

NASA Technical Reports Server (NTRS)

Miele, Angelo

1990-01-01

The research on optimal trajectories for the National Aerospace Plane (NASP) performed by the Aero-Astronautics Group of Rice University from June 22, 1989 to December 31, 1990 is summarized. The aerospace plane is assumed to be controlled via the angle of attack and the power setting. The time history of the controls is optimized simultaneously with the switch times from one powerplant to another and the final time. The intent is to arrive at NASP guidance trajectories exhibiting many of the desirable characteristics of NASP optimal trajectories.

Robust Control Analysis of Hydraulic Turbine Speed

NASA Astrophysics Data System (ADS)

Jekan, P.; Subramani, C.

2018-04-01

An effective control strategy for the hydro-turbine governor in time scenario is adjective for this paper. Considering the complex dynamic characteristic and the uncertainty of the hydro-turbine governor model and taking the static and dynamic performance of the governing system as the ultimate goal, the designed logic combined the classical PID control theory with artificial intelligence used to obtain the desired output. The used controller will be a variable control techniques, therefore, its parameters can be adaptively adjusted according to the information about the control error signal.

Integrating Markets to Bridge Supply and Demand for Knowledge Intensive Tasks

NASA Astrophysics Data System (ADS)

Overbeek, Sietse; Janssen, Marijn; van Bommel, Patrick

The advent of the knowledge-based economy has underlined the importance of intellectual capital that is possessed by knowledge intensive organizations. Three general observations of knowledge intensive work produced by actors working in such organizations served as the basis for the initiation of this research. First, knowledge intensive tasks become increasingly complex. Second, actors that perform such tasks experience an increase in cognitive load. Third, the desired quality of task performance and the produced task results are at stake due to the aforementioned two developments. In this research we investigate how supply and demand of intangible assets such as knowledge, cognitive characteristics, and quality factors can be matched based on market mechanisms.

The biopharmaceutics risk assessment roadmap for optimizing clinical drug product performance.

PubMed

Selen, Arzu; Dickinson, Paul A; Müllertz, Anette; Crison, John R; Mistry, Hitesh B; Cruañes, Maria T; Martinez, Marilyn N; Lennernäs, Hans; Wigal, Tim L; Swinney, David C; Polli, James E; Serajuddin, Abu T M; Cook, Jack A; Dressman, Jennifer B

2014-11-01

The biopharmaceutics risk assessment roadmap (BioRAM) optimizes drug product development and performance by using therapy-driven target drug delivery profiles as a framework to achieve the desired therapeutic outcome. Hence, clinical relevance is directly built into early formulation development. Biopharmaceutics tools are used to identify and address potential challenges to optimize the drug product for patient benefit. For illustration, BioRAM is applied to four relatively common therapy-driven drug delivery scenarios: rapid therapeutic onset, multiphasic delivery, delayed therapeutic onset, and maintenance of target exposure. BioRAM considers the therapeutic target with the drug substance characteristics and enables collection of critical knowledge for development of a dosage form that can perform consistently for meeting the patient's needs. Accordingly, the key factors are identified and in vitro, in vivo, and in silico modeling and simulation techniques are used to elucidate the optimal drug delivery rate and pattern. BioRAM enables (1) feasibility assessment for the dosage form, (2) development and conduct of appropriate "learning and confirming" studies, (3) transparency in decision-making, (4) assurance of drug product quality during lifecycle management, and (5) development of robust linkages between the desired clinical outcome and the necessary product quality attributes for inclusion in the quality target product profile. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Performance Characteristics of a New Generation Pressure Microsensor for Physiologic Applications

PubMed Central

Cottler, Patrick S.; Karpen, Whitney R.; Morrow, Duane A.; Kaufman, Kenton R.

2009-01-01

A next generation fiber-optic microsensor based on the extrinsic Fabry–Perot interferometric (EFPI) technique has been developed for pressure measurements. The basic physics governing the operation of these sensors makes them relatively tolerant or immune to the effects of high-temperature, high-EMI, and highly-corrosive environments. This pressure microsensor represents a significant improvement in size and performance over previous generation sensors. To achieve the desired overall size and sensitivity, numerical modeling of diaphragm deflection was incorporated in the design, with the desired dimensions and calculated material properties. With an outer diameter of approximately 250 µm, a dynamic operating range of over 250 mmHg, and a sampling frequency of 960 Hz, this sensor is ideal for the minimally invasive measurement of physiologic pressures and incorporation in catheter-based instrumentation. Nine individual sensors were calibrated and characterized by comparing the output to a U.S. National Institute of Standards and Technology (NIST) Traceable reference pressure over the range of 0–250 mmHg. The microsensor performance demonstrated accuracy of better than 2% full-scale output, and repeatability, and hysteresis of better than 1% full-scale output. Additionally, fatigue effects on five additional sensors were 0.25% full-scale output after over 10,000 pressure cycles. PMID:19495983

Pattern Recognition Control Design

NASA Technical Reports Server (NTRS)

Gambone, Elisabeth

2016-01-01

Spacecraft control algorithms must know the expected spacecraft response to any command to the available control effectors, such as reaction thrusters or torque devices. Spacecraft control system design approaches have traditionally relied on the estimated vehicle mass properties to determine the desired force and moment, as well as knowledge of the effector performance to efficiently control the spacecraft. A pattern recognition approach can be used to investigate the relationship between the control effector commands and the spacecraft responses. Instead of supplying the approximated vehicle properties and the effector performance characteristics, a database of information relating the effector commands and the desired vehicle response can be used for closed-loop control. A Monte Carlo simulation data set of the spacecraft dynamic response to effector commands can be analyzed to establish the influence a command has on the behavior of the spacecraft. A tool developed at NASA Johnson Space Center (Ref. 1) to analyze flight dynamics Monte Carlo data sets through pattern recognition methods can be used to perform this analysis. Once a comprehensive data set relating spacecraft responses with commands is established, it can be used in place of traditional control laws and gains set. This pattern recognition approach can be compared with traditional control algorithms to determine the potential benefits and uses.

Cognitive ability, social desirability, body mass index and socioeconomic status as correlates of fourth-grade children's dietary-reporting accuracy.

PubMed

Smith, A F; Baxter, S D; Hitchcock, D B; Finney, C J; Royer, J A; Guinn, C H

2016-09-01

To investigate the relationship of reporting accuracy in 24-h dietary recalls to child-respondent characteristics-cognitive ability, social desirability, body mass index (BMI) percentile and socioeconomic status (SES). Fourth-grade children (mean age 10.1 years) were observed eating two school meals and interviewed about dietary intake for 24 h that included those meals. (Eight multiple-pass interview protocols operationalized the conditions of an experiment that crossed two retention intervals-short and long-with four prompts (ways of eliciting reports in the first pass)). Academic achievement-test scores indexed cognitive ability; social desirability was assessed by questionnaire; height and weight were measured to calculate BMI; nutrition-assistance program eligibility information was obtained to index SES. Reported intake was compared to observed intake to calculate measures of reporting accuracy for school meals at the food-item (omission rate; intrusion rate) and energy (correspondence rate; inflation ratio) levels. Complete data were available for 425 of 480 validation-study participants. Controlling for manipulated variables and other measured respondent characteristics, for one or more of the outcome variables, reporting accuracy increased with cognitive ability (omission rate, intrusion rate, correspondence rate, P<0.001), decreased with social desirability (correspondence rate, P<0.0004), decreased with BMI percentile (correspondence rate, P=0.001) and was better by higher- than by lower-SES children (intrusion rate, P=0.001). Some of these effects were moderated by interactions with retention interval and sex. Children's dietary-reporting accuracy is systematically related to such respondent characteristics as cognitive ability, social desirability, BMI percentile and SES.

Study of flowability effect on self-planarization performance at SOC materials

NASA Astrophysics Data System (ADS)

Yun, Huichan; Kim, Jinhyung; Park, Youjung; Kim, Yoona; Jeong, Seulgi; Baek, Jaeyeol; Yoon, Byeri; Lim, Sanghak

2017-03-01

For multilayer process, importance of carbon-based spin-on hardmask material that replaces amorphous carbon layer (ACL) is ever increasing. Carbon-based spin-on hardmask is an organic polymer with high carbon content formulated in organic solvents for spin-coating application that is cured through baking. In comparison to CVD process for ACL, carbon-based spin-on hardmask material can offer several benefits: lower cost of ownership (CoO) and improved process time, as well as better gap-fill and planarization performances. Thus carbon-based spin-on hardmask material of high etch resistance, good gap-fill properties and global planarization performances over various pattern topographies are desired to achieve the fine patterning and high aspect ratio (A/R). In particular, good level of global planarization of spin coated layer over the underlying pattern topographies is important for self-aligned double patterning (SADP) process as it dictates the photolithographic margin. Herein, we report a copolymer carbon-based spin-on hardmask resin formulation that exhibits favorable film shrinkage profile and good etch resistance properties. By combining the favorable characteristics of each resin - one resin with good shrinkage property and the other with excellent etch resistance into the copolymer, it was possible to achieve a carbonbased spin-on hardmask formulation with desirable level of etch resistance and the planarization performances across various underlying substrate pattern topographies.

Stochastic modelling of the hydrologic operation of rainwater harvesting systems

NASA Astrophysics Data System (ADS)

Guo, Rui; Guo, Yiping

2018-07-01

Rainwater harvesting (RWH) systems are an effective low impact development practice that provides both water supply and runoff reduction benefits. A stochastic modelling approach is proposed in this paper to quantify the water supply reliability and stormwater capture efficiency of RWH systems. The input rainfall series is represented as a marked Poisson process and two typical water use patterns are analytically described. The stochastic mass balance equation is solved analytically, and based on this, explicit expressions relating system performance to system characteristics are derived. The performances of a wide variety of RWH systems located in five representative climatic regions of the United States are examined using the newly derived analytical equations. Close agreements between analytical and continuous simulation results are shown for all the compared cases. In addition, an analytical equation is obtained expressing the required storage size as a function of the desired water supply reliability, average water use rate, as well as rainfall and catchment characteristics. The equations developed herein constitute a convenient and effective tool for sizing RWH systems and evaluating their performances.

A piloted simulation of helicopter air combat to investigate effects of variations in selected performance and control response characteristics

NASA Technical Reports Server (NTRS)

Lewis, Michael S.; Mansur, M. Hossein; Chen, Robert T. N.

1987-01-01

A piloted simulation study investigating handling qualities and flight characteristics required for helicopter air to air combat is presented. The Helicopter Air Combat system was used to investigate this role for Army rotorcraft. Experimental variables were the maneuver envelope size (load factor and sideslip), directional axis handling qualities, and pitch and roll control-response type. Over 450 simulated, low altitude, one-on-one engagements were conducted. Results from the experiment indicate that a well damped directional response, low sideforce caused by sideslip, and some effective dihedral are all desirable for weapon system performance, good handling qualities, and low pilot workload. An angular rate command system was favored over the attitude type pitch and roll response for most applications, and an enhanced maneuver envelope size over that of current generation aircraft was found to be advantageous. Pilot technique, background, and experience are additional factors which had a significant effect on performance in the air combat tasks investigated. The implication of these results on design requirements for future helicopters is presented.

Spacer engineered Trigate SOI TFET: An investigation towards harsh temperature environment applications

NASA Astrophysics Data System (ADS)

Mallikarjunarao; Ranjan, Rajeev; Pradhan, K. P.; Artola, L.; Sahu, P. K.

2016-09-01

In this paper, a novel N-channel Tunnel Field Effect Transistor (TFET) i.e., Trigate Silicon-ON-Insulator (SOI) N-TFET with high-k spacer is proposed for better Sub-threshold swing (SS) and OFF-state current (IOFF) by keeping in mind the sensitivity towards temperature. The proposed model can achieve a Sub-threshold swing less than 35 mV/decade at various temperatures, which is desirable for designing low power CTFET for digital circuit applications. In N-TFET source doping has a significant effect on the ON-state current (ION) level; therefore more electrons will tunnel from source to channel region. High-k Spacer i.e., HfO2 is used to enhance the device performance and also it avoids overlapping of transistors in an integrated circuits (IC's). We have designed a reliable device by performing the temperature analysis on Transfer characteristics, Drain characteristics and also on various performance metrics like ON-state current (ION), OFF-state current (IOFF), ION/IOFF, Trans-conductance (gm), Trans-conductance Generation Factor (TGF), Sub-threshold Swing (SS) to observe the applications towards harsh temperature environment.

Grey Relational Analysis Coupled with Principal Component Analysis for Optimization of Stereolithography Process to Enhance Part Quality

NASA Astrophysics Data System (ADS)

Raju, B. S.; Sekhar, U. Chandra; Drakshayani, D. N.

2017-08-01

The paper investigates optimization of stereolithography process for SL5530 epoxy resin material to enhance part quality. The major characteristics indexed for performance selected to evaluate the processes are tensile strength, Flexural strength, Impact strength and Density analysis and corresponding process parameters are Layer thickness, Orientation and Hatch spacing. In this study, the process is intrinsically with multiple parameters tuning so that grey relational analysis which uses grey relational grade as performance index is specially adopted to determine the optimal combination of process parameters. Moreover, the principal component analysis is applied to evaluate the weighting values corresponding to various performance characteristics so that their relative importance can be properly and objectively desired. The results of confirmation experiments reveal that grey relational analysis coupled with principal component analysis can effectively acquire the optimal combination of process parameters. Hence, this confirm that the proposed approach in this study can be an useful tool to improve the process parameters in stereolithography process, which is very useful information for machine designers as well as RP machine users.

Field observations using an AOTF polarimetric imaging spectrometer

NASA Technical Reports Server (NTRS)

Cheng, Li-Jen; Hamilton, Mike; Mahoney, Colin; Reyes, George

1993-01-01

This paper reports preliminary results of recent field observations using a prototype acousto-optic tunable filter (AOTF) polarimetric imaging spectrometer. The data illustrate application potentials for geoscience. The operation principle of this instrument is different from that of current airborne multispectral imaging instruments, such as AVIRIS. The AOTF instrument takes two orthogonally polarized images at a desired wavelength at one time, whereas AVIRIS takes a spectrum over a predetermined wavelength range at one pixel at a time and the image is constructed later. AVIRIS does not have any polarization measuring capability. The AOTF instrument could be a complement tool to AVIRIS. Polarization measurement is a desired capability for many applications in remote sensing. It is well know that natural light is often polarized due to various scattering phenomena in the atmosphere. Also, scattered light from canopies is reported to have a polarized component. To characterize objects of interest correctly requires a remote sensing imaging spectrometer capable of measuring object signal and background radiation in both intensity and polarization so that the characteristics of the object can be determined. The AORF instrument has the capability to do so. The AOTF instrument has other unique properties. For example, it can provide spectral images immediately after the observation. The instrument can also allow observations to be tailored in real time to perform the desired experiments and to collect only required data. Consequently, the performance in each mission can be increased with minimal resources. The prototype instrument was completed in the beginning of this year. A number of outdoor field experiments were performed with the objective to evaluate the capability of this new technology for remote sensing applications and to determine issues for further improvements.

Linear quadratic servo control of a reusable rocket engine

NASA Technical Reports Server (NTRS)

Musgrave, Jeffrey L.

1991-01-01

The paper deals with the development of a design method for a servo component in the frequency domain using singular values and its application to a reusable rocket engine. A general methodology used to design a class of linear multivariable controllers for intelligent control systems is presented. Focus is placed on performance and robustness characteristics, and an estimator design performed in the framework of the Kalman-filter formalism with emphasis on using a sensor set different from the commanded values is discussed. It is noted that loop transfer recovery modifies the nominal plant noise intensities in order to obtain the desired degree of robustness to uncertainty reflected at the plant input. Simulation results demonstrating the performance of the linear design on a nonlinear engine model over all power levels during mainstage operation are discussed.

Linearization of digital derived rate algorithm for use in linear stability analysis

NASA Technical Reports Server (NTRS)

Graham, R. E.; Porada, T. W.

1985-01-01

The digital derived rate (DDR) algorithm is used to calculate the rate of rotation of the Centaur upper-stage rocket. The DDR is highly nonlinear algorithm, and classical linear stability analysis of the spacecraft cannot be performed without linearization. The performance of this rate algorithm is characterized by a gain and phase curve that drop off at the same frequency. This characteristic is desirable for many applications. A linearization technique for the DDR algorithm is investigated. The linearization method is described. Examples of the results of the linearization technique are illustrated, and the effects of linearization are described. A linear digital filter may be used as a substitute for performing classical linear stability analyses, while the DDR itself may be used in time response analysis.

Advanced High-Definition Video Cameras

NASA Technical Reports Server (NTRS)

Glenn, William

2007-01-01

A product line of high-definition color video cameras, now under development, offers a superior combination of desirable characteristics, including high frame rates, high resolutions, low power consumption, and compactness. Several of the cameras feature a 3,840 2,160-pixel format with progressive scanning at 30 frames per second. The power consumption of one of these cameras is about 25 W. The size of the camera, excluding the lens assembly, is 2 by 5 by 7 in. (about 5.1 by 12.7 by 17.8 cm). The aforementioned desirable characteristics are attained at relatively low cost, largely by utilizing digital processing in advanced field-programmable gate arrays (FPGAs) to perform all of the many functions (for example, color balance and contrast adjustments) of a professional color video camera. The processing is programmed in VHDL so that application-specific integrated circuits (ASICs) can be fabricated directly from the program. ["VHDL" signifies VHSIC Hardware Description Language C, a computing language used by the United States Department of Defense for describing, designing, and simulating very-high-speed integrated circuits (VHSICs).] The image-sensor and FPGA clock frequencies in these cameras have generally been much higher than those used in video cameras designed and manufactured elsewhere. Frequently, the outputs of these cameras are converted to other video-camera formats by use of pre- and post-filters.

System-state and operating condition sensitive control method and apparatus for electric power delivery systems

NASA Technical Reports Server (NTRS)

Burns, III, William Wesley (Inventor); Wilson, Thomas George (Inventor)

1978-01-01

This invention provides a method and apparatus for determining a precise switching sequence for the power switching elements of electric power delivery systems of the on-off switching type and which enables extremely fast transient response, precise regulation and highly stable operation. The control utilizes the values of the power delivery system power handling network components, a desired output characteristic, a system timing parameter, and the externally imposed operating conditions to determine where steady state operations should be in order to yield desired output characteristics for the given system specifications. The actual state of the power delivery system is continuously monitored and compared to a state-space boundary which is derived from the desired equilibrium condition, and from the information obtained from this comparison, the system is moved to the desired equilibrium condition in one cycle of switching control. Since the controller continuously monitors the power delivery system's externally imposed operating conditions, a change in the conditions is immediately sensed and a new equilibrium condition is determined and achieved, again in a single cycle of switching control.

The Parametric Study and Fine-Tuning of Bow-Tie Slot Antenna with Loaded Stub

PubMed Central

2017-01-01

A printed Bow-Tie slot antenna with loaded stub is proposed and the effects of changing the dimensions of the slot area, the stub and load sizes are considered in this paper. These parameters have a considerable effect on the antenna characteristics as well as its performance. An in-depth parametric study of these dimensions is presented. This paper proposes the necessary conditions for initial approximation of dimensions needed to design this antenna. In order to achieve the desired performance of the antenna fine tuning of all sizes of these parameters is required. The parametric studies used in this paper provide proper trends for initiation and tuning the design. A prototype of the antenna for 1.7GHz to 2.6GHz band is fabricated. Measurements conducted verify that the designed antenna has wideband characteristics with 50% bandwidth around the center frequency of 2.1GHz. Conducted measurements for reflection coefficient (S11) and radiation pattern also validate our simulation results. PMID:28114354

The Parametric Study and Fine-Tuning of Bow-Tie Slot Antenna with Loaded Stub.

PubMed

Shafiei, M M; Moghavvemi, Mahmoud; Wan Mahadi, Wan Nor Liza

2017-01-01

A printed Bow-Tie slot antenna with loaded stub is proposed and the effects of changing the dimensions of the slot area, the stub and load sizes are considered in this paper. These parameters have a considerable effect on the antenna characteristics as well as its performance. An in-depth parametric study of these dimensions is presented. This paper proposes the necessary conditions for initial approximation of dimensions needed to design this antenna. In order to achieve the desired performance of the antenna fine tuning of all sizes of these parameters is required. The parametric studies used in this paper provide proper trends for initiation and tuning the design. A prototype of the antenna for 1.7GHz to 2.6GHz band is fabricated. Measurements conducted verify that the designed antenna has wideband characteristics with 50% bandwidth around the center frequency of 2.1GHz. Conducted measurements for reflection coefficient (S11) and radiation pattern also validate our simulation results.

Design of set-point weighting PI{sup λ} + D{sup μ} controller for vertical magnetic flux controller in Damavand tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rasouli, H.; Fatehi, A.

2014-12-15

In this paper, a simple method is presented for tuning weighted PI{sup λ} + D{sup μ} controller parameters based on the pole placement controller of pseudo-second-order fractional systems. One of the advantages of this controller is capability of reducing the disturbance effects and improving response to input, simultaneously. In the following sections, the performance of this controller is evaluated experimentally to control the vertical magnetic flux in Damavand tokamak. For this work, at first a fractional order model is identified using output-error technique in time domain. For various practical experiments, having desired time responses for magnetic flux in Damavand tokamak,more » is vital. To approach this, at first the desired closed loop reference models are obtained based on generalized characteristic ratio assignment method in fractional order systems. After that, for the identified model, a set-point weighting PI{sup λ} + D{sup μ} controller is designed and simulated. Finally, this controller is implemented on digital signal processor control system of the plant to fast/slow control of magnetic flux. The practical results show appropriate performance of this controller.« less

Aerodynamic Design Using Neural Networks

NASA Technical Reports Server (NTRS)

Rai, Man Mohan; Madavan, Nateri K.

2003-01-01

The design of aerodynamic components of aircraft, such as wings or engines, involves a process of obtaining the most optimal component shape that can deliver the desired level of component performance, subject to various constraints, e.g., total weight or cost, that the component must satisfy. Aerodynamic design can thus be formulated as an optimization problem that involves the minimization of an objective function subject to constraints. A new aerodynamic design optimization procedure based on neural networks and response surface methodology (RSM) incorporates the advantages of both traditional RSM and neural networks. The procedure uses a strategy, denoted parameter-based partitioning of the design space, to construct a sequence of response surfaces based on both neural networks and polynomial fits to traverse the design space in search of the optimal solution. Some desirable characteristics of the new design optimization procedure include the ability to handle a variety of design objectives, easily impose constraints, and incorporate design guidelines and rules of thumb. It provides an infrastructure for variable fidelity analysis and reduces the cost of computation by using less-expensive, lower fidelity simulations in the early stages of the design evolution. The initial or starting design can be far from optimal. The procedure is easy and economical to use in large-dimensional design space and can be used to perform design tradeoff studies rapidly. Designs involving multiple disciplines can also be optimized. Some practical applications of the design procedure that have demonstrated some of its capabilities include the inverse design of an optimal turbine airfoil starting from a generic shape and the redesign of transonic turbines to improve their unsteady aerodynamic characteristics.

Nanotextured Surfaces and Related Methods, Systems, and Uses

NASA Technical Reports Server (NTRS)

Greer, Harold F. (Inventor); Greer, Julia R. (Inventor)

2014-01-01

A method of controlling wetting characteristics is described. Such method includes forming and configuring nanostructures on a surface where controlling of the wetting characteristics is desired. Surfaces and methods of fabricating such surfaces are also described.

Characterization of Solidifiers used for Oil Spill Remediation

EPA Science Inventory

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial...

Taguchi's off line method and Multivariate loss function approach for quality management and optimization of process parameters -A review

NASA Astrophysics Data System (ADS)

Bharti, P. K.; Khan, M. I.; Singh, Harbinder

2010-10-01

Off-line quality control is considered to be an effective approach to improve product quality at a relatively low cost. The Taguchi method is one of the conventional approaches for this purpose. Through this approach, engineers can determine a feasible combination of design parameters such that the variability of a product's response can be reduced and the mean is close to the desired target. The traditional Taguchi method was focused on ensuring good performance at the parameter design stage with one quality characteristic, but most products and processes have multiple quality characteristics. The optimal parameter design minimizes the total quality loss for multiple quality characteristics. Several studies have presented approaches addressing multiple quality characteristics. Most of these papers were concerned with maximizing the parameter combination of signal to noise (SN) ratios. The results reveal the advantages of this approach are that the optimal parameter design is the same as the traditional Taguchi method for the single quality characteristic; the optimal design maximizes the amount of reduction of total quality loss for multiple quality characteristics. This paper presents a literature review on solving multi-response problems in the Taguchi method and its successful implementation in various industries.

Toward scalable parts families for predictable design of biological circuits.

PubMed

Lucks, Julius B; Qi, Lei; Whitaker, Weston R; Arkin, Adam P

2008-12-01

Our current ability to engineer biological circuits is hindered by design cycles that are costly in terms of time and money, with constructs failing to operate as desired, or evolving away from the desired function once deployed. Synthetic biologists seek to understand biological design principles and use them to create technologies that increase the efficiency of the genetic engineering design cycle. Central to the approach is the creation of biological parts--encapsulated functions that can be composited together to create new pathways with predictable behaviors. We define five desirable characteristics of biological parts--independence, reliability, tunability, orthogonality and composability, and review studies of small natural and synthetic biological circuits that provide insights into each of these characteristics. We propose that the creation of appropriate sets of families of parts with these properties is a prerequisite for efficient, predictable engineering of new function in cells and will enable a large increase in the sophistication of genetic engineering applications.

Chemical characteristics and volatile profile of genetically modified peanut cultivars.

PubMed

Ng, Ee Chin; Dunford, Nurhan T; Chenault, Kelly

2008-10-01

Genetic engineering has been used to modify peanut cultivars for improving agronomic performance and pest resistance. Food products developed through genetic engineering have to be assessed for their safety before approval for human consumption. Preservation of desirable chemical, flavor and aroma attributes of the peanut cultivars during the genetic modifications is critical for acceptance of genetically modified peanuts (GMP) by the food industry. Hence, the main objective of this study is to examine chemical characteristics and volatile profile of GMP. The genetically modified peanut cultivars, 188, 540 and 654 were obtained from the USDA-ARS in Stillwater, Oklahoma. The peanut variety Okrun was examined as a control. The volatile analysis was performed using a gas chromatograph/mass spectrometer (GC/MS) equipped with an olfactory detector. The peanut samples were also analyzed for their moisture, ash, protein, sugar and oil compositions. Experimental results showed that the variations in nutritional composition of peanut lines examined in this study were within the values reported for existing cultivars. There were minor differences in volatile profile among the samples. The implication of this study is significant, since it shows that peanut cultivars with greater pest and fungal resistance were successfully developed without major changes in their chemical characteristics.

Crude glycerine inclusion in Limousin bull diets: animal performance, carcass characteristics and meat quality.

PubMed

Egea, M; Linares, M B; Garrido, M D; Villodre, C; Madrid, J; Orengo, J; Martínez, S; Hernández, F

2014-12-01

Three hundred and six Limousin young bulls (7±1months of age, initial body weight 273±43kg) were used to evaluate the effect of crude glycerine supplementation on animal performance, carcass characteristics and meat quality. Animals were assigned to three different diets: Control (0% of crude glycerine), G2 and G4 (2 and 4% of crude glycerine, respectively). The diets were administrated ad libitum for 240days (final body weight 644±24kg). Average daily weight gain, average daily feed intake, the gain:feed ratio, ultrasound measures in vivo, carcass characteristics, pH, water holding capacity, drip losses, and cooking losses were not affected (P>0.05) by diets. Diet decreased C16:0 (P<0.01) and C16:1 (P<0.05) contents in meat. The G4 meat showed lower C12:0, C14:0, C17:0, C18:0, C18:1, C18:2, C18:3, c9,t11-c18:2, C20:0 and C20:4 levels (P<0.05) than control. Glycerine increased desirable fatty acid percentages (P<0.05) in intramuscular fat. Copyright © 2014 Elsevier Ltd. All rights reserved.

A functional neuroimaging study assessing gender differences in the neural mechanisms underlying the ability to resist impulsive desires.

PubMed

Diekhof, Esther K; Keil, Maria; Obst, Katrin U; Henseler, Ilona; Dechent, Peter; Falkai, Peter; Gruber, Oliver

2012-09-14

There is ample evidence of gender differences in neural processes and behavior. Differences in reward-related behaviors have been linked to either temporary or permanent organizational influences of gonadal hormones on the mesolimbic dopamine system and reward-related activation. Still, little is known about the association between biological gender and the neural underpinnings of the ability to resist reward-related impulses. Here we assessed with functional magnetic resonance imaging which neural processes enable men and women to successfully control their desire for immediate reward when this is required by a higher-order goal (i.e., during a 'desire-reason dilemma'; Diekhof and Gruber, 2010). Thirty-two participants (16 females) were closely matched for age, personality characteristics (e.g., novelty seeking) and behavioral performance in the 'desire-reason task'. On the neural level, men and women showed similarities in the general response of the nucleus accumbens and of the ventral tegmental area to predictors of immediate reward, but they differed in additional brain mechanisms that enabled self-controlled decisions against the preference for immediate reward. Firstly, men exhibited a stronger reduction of activation in the ventral pallidum, putamen, temporal pole and pregenual anterior cingulate cortex during the 'desire-reason dilemma'. Secondly, connectivity analyses revealed a significant change in the direction of the connectivity between anteroventral prefrontal cortex and nucleus accumbens during decisions counteracting the reward-related impulse when comparing men and women. Together, these findings support the view of a sexual dimorphism that manifested in the recruitment of gender-specific neural resources during the successful deployment of self-control. Copyright © 2012 Elsevier B.V. All rights reserved.

Power of the Desired Self: Influence of Induced Perceptions of the Self on Reasoning

ERIC Educational Resources Information Center

Augustinova, Maria; Collange, Julie; Sanitioso, Rasyid Bo; Musca, Serban C.

2011-01-01

This research shows that the motivation to posses a desired characteristic (or to avoid an undesired one) results in self-perceptions that guide people's use of base rate in the Lawyer-Engineer problem (Kahneman & Tversky, 1973). In four studies, participants induced to believe (or recall, Exp. 2) that a rational cognitive style is…

Beliefs of Applied Studio Faculty on Desirable Traits of Prospective Music Education Majors

ERIC Educational Resources Information Center

Royston, Natalie Steele; Springer, D. Gregory

2017-01-01

The purpose of this study was to examine the beliefs of applied music faculty on desirable traits of prospective music education majors. Respondents (N = 326), who were sampled from 73 National Association of Schools of Music-accredited institutions in the United States, completed a survey instrument developed to determine the characteristics of…

Assessment of the Relationship Between Flexibility and Adaptive Capacity in Flood Management Systems

NASA Astrophysics Data System (ADS)

DiFrancesco, K.; Tullos, D. D.

2013-12-01

Discussions around adapting water management systems to future changes often state the need to increase system flexibility. Intuitively, a flexible, easily modifiable system seems desirable when faced with a wide range of uncertain, but plausible future conditions. Yet, despite the frequent use of the terms flexibility, very little work has examined what exactly it means to have a flexible water management system, what makes one system more flexible than another, or the extent to which flexibility increases adaptive capacity. This study applies a methodology for assessing the inherent flexibility of the structural and non-structural components of flood management systems using original flexibility metrics in the categories of: slack, intensity, connectivity, adjustability, and coordination. We use these metrics to assess the flexibility of three sub-systems within the Sacramento Valley flood management system in California, USA under current system conditions as well as with proposed management actions in place. We then assess the range of hydrologic conditions under which each sub-system can meet flood risk targets in order to determine whether more flexible systems are also more robust and able to perform over a wider range of hydrologic conditions. In doing so, we identify flexible characteristics of flood management systems that enhance the ability of the system to preform over a wide range of conditions making them better suited to adapt to an uncertain hydrologic future. We find that the flexibility characteristics that increase the range of conditions under which the system can meet performance goals varies depending on whether the region is considered urban, rural, or a small community. In some cases, a decrease in certain flexibility characteristics is associated with an increase in robustness, indicating that more flexibility is not always desirable. Future work will assess the transferability of these results to other regions and systems.

Desire for tooth bleaching and treatment performed in Brazilian adults: findings from a birth cohort.

PubMed

Silva, Fernando Barcellos da; Chisini, Luiz Alexandre; Demarco, Flávio Fernando; Horta, Bernardo Lessa; Correa, Marcos Britto

2018-03-08

Population-based studies estimating the prevalence of tooth bleaching desire or the percentage of individuals who had performed this treatment are rare. Thus, the aim of this study was to evaluate the desire to perform tooth bleaching and the prevalence of adult individuals who had performed the treatment and investigate the association of these outcomes. A subsample (n = 536) of the 1982 Pelotas birth cohort in southern Brazil was investigated at the ages 15, 24 and 31 by clinical examinations and interviews. The prevalence of bleaching at 31 years was 15.6% [95%CI 12.6-18.9] while 85.9% [95%CI 82.7-88.7] reported they desired the treatment. Multivariate Poisson regression analysis showed that individuals who have visited the dentist within the last year showed a treatment prevalence ratio (PR) 2.31 times [95%CI 1.40-3.83] higher compared with those who had the last dental visit more than a year before the interview. Similarly, individuals with smoking habits presented an elevated PR of 1.60 [95%CI 1.00-2.55], and the low-income trajectory group showed the largest PR of desire for tooth bleaching (1.17 [95%CI 1.07-1.28]). Moreover, individuals from the high-risk caries trajectory group presented a higher prevalence of desire for tooth bleaching than individuals from low caries trajectory group. Individuals who have declared being "dissatisfied" with their dental color presented a prevalence of desire for tooth bleaching 16% greater than "satisfied" ones. Thus, the present findings confirm that tooth bleaching has become a frequently desired dental treatment to improve dental aesthetics in the population and a considerable rate of adults has performed the treatment.

Athletes' assessment of the coach--the coach evaluation questionnaire.

PubMed

Rushall, B S; Wiznuk, K

1985-09-01

The purpose of this study was to provide an assessment tool to judge coaching performance that was appropriate for completion by athletes. The questionnaire underwent a variety of developmental stages. In its final form, it contained 36 items. The tool was shown to be a valid, reliable, and standardized questionnaire. It demonstrated discriminability and provoked honest, accurate responding in subjects. The test was capable of providing immediate feedback to coaches seeking information about athletes' perceptions of their coaching performance. Responses on the developed scale were weighted to reflect the desirability of the coaching characteristics of a good coach. The questionnaire provides a total score which can be interpreted by the coach as a measure of how much of an "ideal" coach exists in him/her.

Toward Evolvable Hardware Chips: Experiments with a Programmable Transistor Array

NASA Technical Reports Server (NTRS)

Stoica, Adrian

1998-01-01

Evolvable Hardware is reconfigurable hardware that self-configures under the control of an evolutionary algorithm. We search for a hardware configuration can be performed using software models or, faster and more accurate, directly in reconfigurable hardware. Several experiments have demonstrated the possibility to automatically synthesize both digital and analog circuits. The paper introduces an approach to automated synthesis of CMOS circuits, based on evolution on a Programmable Transistor Array (PTA). The approach is illustrated with a software experiment showing evolutionary synthesis of a circuit with a desired DC characteristic. A hardware implementation of a test PTA chip is then described, and the same evolutionary experiment is performed on the chip demonstrating circuit synthesis/self-configuration directly in hardware.

CEOs and CFOs express concern about materials management.

PubMed

Kowalski, J C

1998-05-01

In a recent survey, CEOs and CFOs expressed concern regarding the effectiveness of their materials management departments. Both groups of executives would like to see more improvement in their materials managers' supply expense reduction efforts and leadership skills. More than a third of CFOs are even considering outsourcing the materials management function. Both CEOs and CFOs did admit, however, they needed to learn more about materials management, and both groups of executives could lend their authority to materials management programs to ensure their success. CEOs and CFOs need to reach consensus regard materials management priorities, performance levels, and professional characteristics and desired skills. They also should hold materials managers accountable for operations they can and should be managing by using performance-based compensation.

Reliability Considerations of ULP Scaled CMOS in Spacecraft Systems

NASA Technical Reports Server (NTRS)

White, Mark; MacNeal, Kristen; Cooper, Mark

2012-01-01

NASA, the aerospace community, and other high reliability (hi-rel) users of advanced microelectronic products face many challenges as technology continues to scale into the deep sub-micron region. Decreasing the feature size of CMOS devices not only allows more components to be placed on a single chip, but it increases performance by allowing faster switching (or clock) speeds with reduced power compared to larger scaled devices. Higher performance, and lower operating and stand-by power characteristics of Ultra-Low Power (ULP) microelectronics are not only desirable, but also necessary to meet low power consumption design goals of critical spacecraft systems. The integration of these components in such systems, however, must be balanced with the overall risk tolerance of the project.

Parent-child relationships and self‑control in male university students' desire to play video games.

PubMed

Karbasizadeh, Sina; Jani, Masih; Keshvari, Mahtab

2018-06-12

To determine the relationship between the parent-child relationship, self-control and demographic characteristics and the desire to play video games among male university students at one university in Iran. This was a correlational, descriptive, applied study. A total of 103 male students were selected randomly as a study sample from the population of male students at Isfahan University in Iran. Data collection tools used were the Video Games Questionnaire, Tanji's Self-Control Scale, Parent-Child Relationship Questionnaire, and Demographic Questionnaire. Data were analysed using stepwise regression analysis. This study found several factors increased male students' desire to play video games. Demographic characteristics associated with increased tendency to play video games among male students in Iran are older age, larger number of family members, lower parental level of education and higher socio-economic class, while other significant factors are a lower level of self‑control and a poorer parent-child relationship. PARTICIPANTS': higher socio-economic class, lower level of self-control and older age explained 8.2%, 5.2% and 5.9% of their desire to play video games, respectively. These three variables together accounted for significantly 16.9% of a male student's desire to play video games in this study ( P <0.05). These results suggest that the family's socio-economic status plays a significant role in young men's desire to play video games in Iran. Moreover, lower levels of self-control and a poorer parent-child relationship were found to be accompanied by a greater desire to play video games among male university students. © 2018 RCN Publishing Company Ltd. All rights reserved. Not to be copied, transmitted or recorded in any way, in whole or part, without prior permission of the publishers.

Latino Parents' Perceptions of Pediatric Weight Counseling Terms.

PubMed

Knierim, Shanna Doucette; Newcomer, Sophia; Castillo, Alyssa; Rahm, Alanna Kulchak; Raghunath, Silvia; Clarke, Christina; Wright, Leslie; Haemer, Matthew; Hambidge, Simon J

2018-04-01

Little is known about Latino parents' perceptions of weight-related language in English or Spanish, particularly for counseling obese youth. We sought to identify English and Spanish weight counseling terms perceived by Latino parents across demographic groups as desirable for providers to use, motivating, and inoffensive. Latino parents of children treated at urban safety-net clinics completed surveys in English or Spanish. Parents rated the desirable, motivating, or offensive properties of terms for excess weight using a 5-point scale. We compared parental ratings of terms and investigated the association of parent and child characteristics with parent perceptions of terms. A total of 525 surveys met inclusion criteria (255 English, 270 Spanish). English survey respondents rated "unhealthy weight" and "too much weight for his/her health" the most motivating and among the most desirable and least offensive terms. Spanish survey respondents found "demasiado peso para su salud" highly desirable, highly motivating, and inoffensive, and respondents valued its connection to the child's health. Commonly used clinical terms "overweight"/"sobrepeso" and "high BMI [body mass index]"/"índice de masa corporal alta" were not as desirable or as motivating. "Chubby," "fat," "gordo," and "muy gordo" were the least motivating and most offensive terms. Parents' ratings of commonly used clinical terms varied widely across demographic groups, but more desirable terms had less variability. "Unhealthy weight," "too much weight for his/her health," and its Spanish equivalent, "demasiado peso para su salud," were the most desirable and motivating, and the least offensive terms. Latino parents' positive perceptions of these terms occurred across parent and child characteristics, supporting their use in weight counseling. Copyright © 2017 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

Deposition of Nanostructured Thin Film from Size-Classified Nanoparticles

NASA Technical Reports Server (NTRS)

Camata, Renato P.; Cunningham, Nicholas C.; Seol, Kwang Soo; Okada, Yoshiki; Takeuchi, Kazuo

2003-01-01

Materials comprising nanometer-sized grains (approximately 1_50 nm) exhibit properties dramatically different from those of their homogeneous and uniform counterparts. These properties vary with size, shape, and composition of nanoscale grains. Thus, nanoparticles may be used as building blocks to engineer tailor-made artificial materials with desired properties, such as non-linear optical absorption, tunable light emission, charge-storage behavior, selective catalytic activity, and countless other characteristics. This bottom-up engineering approach requires exquisite control over nanoparticle size, shape, and composition. We describe the design and characterization of an aerosol system conceived for the deposition of size classified nanoparticles whose performance is consistent with these strict demands. A nanoparticle aerosol is generated by laser ablation and sorted according to size using a differential mobility analyzer. Nanoparticles within a chosen window of sizes (e.g., (8.0 plus or minus 0.6) nm) are deposited electrostatically on a surface forming a film of the desired material. The system allows the assembly and engineering of thin films using size-classified nanoparticles as building blocks.

[Maintenance treatment in opioid-dependent patients with migration background].

PubMed

Bald, L K; Schouler-Ocak, M; Penka, S; Schoofs, N; Häbel, T; Bermpohl, F; Gutwinski, S

2016-05-01

No regional analyses regarding opioid-dependent patients in maintenance treatment with a migration background have so far been performed in German-speaking countries. This study examined patients with and without a migration background regarding socioeconomic parameters, characteristics of dependency and attitude towards opiate maintenance treatment (OMT). From May to October 2011 patients in OMT from all of the 20 psychiatry clinics and 110 physician practices in Berlin with a licence to provide OMT were included in this analysis. Out of the 986 participating patients, 956 gave information on migration background and of these, 204 (21.3 %) originated from a country other than Germany. Compared to patients without a migration background, their participation in a maintenance program was significantly shorter and they more often expressed a desire to end OMT and wanted a limited duration of OMT. The differences regarding duration of OMT and the wish to end OMT can reflect a stronger desire for abstinence and a different attitude towards maintenance treatment of patients with a migration background.

Use of Osmotic Pumps to Establish the Pharmacokinetic-Pharmacodynamic Relationship and Define Desirable Human Performance Characteristics for Aggrecanase Inhibitors.

PubMed

Wiley, Michael R; Durham, Timothy B; Adams, Lisa A; Chambers, Mark G; Lin, Chaohua; Liu, Chin; Marimuthu, Jothirajah; Mitchell, Peter G; Mudra, Daniel R; Swearingen, Craig A; Toth, James L; Weller, Jennifer M; Thirunavukkarasu, Kannan

2016-06-23

The development of reliable relationships between in vivo target engagement, pharmacodynamic activity, and efficacy in chronic disease models is beneficial for enabling hypothesis-driven drug discovery and facilitating the development of patient-focused candidate selection criteria. Toward those ends, osmotic infusion pumps can be useful for overcoming limitations in the PK properties of proof-of-concept (POC) compounds to accelerate the development of such relationships. In this report, we describe the application of this strategy to the development of hydantoin-derived aggrecanase inhibitors (eg, 3) for the treatment of osteoarthiritis (OA). Potent, selective inhibitors were efficacious in both chemical and surgical models of OA when exposures were sustained in excess of 10 times the plasma IC50. The use of these data for establishing patient-focused candidate selection criteria is exemplified with the characterization of compound 8, which is projected to sustain the desired level of target engagement at a dose of 45 mg qd.

Effects of various conditions in cold-welding of copper nanowires: A molecular dynamics study

NASA Astrophysics Data System (ADS)

Zhou, Hongjian; Wu, Wen-ping; Wu, Runni; Hu, Guoming; Xia, Re

2017-11-01

Cold-welding possesses such desirable environment as low temperature and low applied stress, thus becoming the prime candidate for nanojointing and nanoassembly techniques. To explore the welding mechanism of nanoscale structures, here, molecular dynamics was performed on copper nanowires under different welding conditions and various original characteristics to obtain an atomic-level depiction of their cold-welding behavior. By analyzing the mechanical properties of as-welded nanowires, the relations between welding quality and welding variables are revealed and identified. This comparison study will be of great importance to future mechanical processing and structural assembly of metallic nanowires.

Dynamic load simulator

NASA Technical Reports Server (NTRS)

Joncas, K. P.

1972-01-01

Concepts and techniques for identifying and simulating both the steady state and dynamic characteristics of electrical loads for use during integrated system test and evaluation are discussed. The investigations showed that it is feasible to design and develop interrogation and simulation equipment to perform the desired functions. During the evaluation, actual spacecraft loads were interrogated by stimulating the loads with their normal input voltage and measuring the resultant voltage and current time histories. Elements of the circuits were optimized by an iterative process of selecting element values and comparing the time-domain response of the model with those obtained from the real equipment during interrogation.

Genetic algorithms using SISAL parallel programming language

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tejada, S.

1994-05-06

Genetic algorithms are a mathematical optimization technique developed by John Holland at the University of Michigan [1]. The SISAL programming language possesses many of the characteristics desired to implement genetic algorithms. SISAL is a deterministic, functional programming language which is inherently parallel. Because SISAL is functional and based on mathematical concepts, genetic algorithms can be efficiently translated into the language. Several of the steps involved in genetic algorithms, such as mutation, crossover, and fitness evaluation, can be parallelized using SISAL. In this paper I will l discuss the implementation and performance of parallel genetic algorithms in SISAL.

Evaluation of mixed solvent electrolytes for ambient temperature secondary lithium cells

NASA Technical Reports Server (NTRS)

Shen, D. H.; Subbarao, S.; Deligiannis, F.; Dawson, S.; Halpert, G.

1988-01-01

The ethylene carbonate/2-methyltetrahydrofuran (EC/2-MeTHF) mixed-solvent electrolyte has been experimentally found to possess many desirable electrolyte characteristics for ambient-temperature secondary Li-TiS2 cell applications. As many as 300 cycles have been demonstrated, and a cycling efficiency figure-of-merit of 38.5 percent, for 10-percent EC/90-percent MeTHF mixed-solvent electrolyte in experimental Li-TiS2 cells. The improved performance of this electrolyte is attributable to the formation of a beneficial passivating film on the Li electrode by interaction with the EC.

Wet active chevron nozzle for controllable jet noise reduction

NASA Technical Reports Server (NTRS)

Thomas, Russell H. (Inventor); Kinzie, Kevin W. (Inventor)

2011-01-01

Disposed at or toward the trailing edge of one or more nozzles associated with a jet engine are injection ports which can selectively be made to discharge a water stream into a nozzle flow stream for the purpose of increasing turbulence in somewhat of a similar fashion as mechanically disposed chevrons have done in the known art. Unlike mechanically disposed chevrons of the known art, the fluid flow may be secured thereby increasing the engine efficiency. Various flow patterns, water pressures, orifice designs or other factors can be made operative to provide desired performance characteristics.

Neural network based system for equipment surveillance

DOEpatents

Vilim, Richard B.; Gross, Kenneth C.; Wegerich, Stephan W.

1998-01-01

A method and system for performing surveillance of transient signals of an industrial device to ascertain the operating state. The method and system involves the steps of reading into a memory training data, determining neural network weighting values until achieving target outputs close to the neural network output. If the target outputs are inadequate, wavelet parameters are determined to yield neural network outputs close to the desired set of target outputs and then providing signals characteristic of an industrial process and comparing the neural network output to the industrial process signals to evaluate the operating state of the industrial process.

Neural network based system for equipment surveillance

DOEpatents

Vilim, R.B.; Gross, K.C.; Wegerich, S.W.

1998-04-28

A method and system are disclosed for performing surveillance of transient signals of an industrial device to ascertain the operating state. The method and system involves the steps of reading into a memory training data, determining neural network weighting values until achieving target outputs close to the neural network output. If the target outputs are inadequate, wavelet parameters are determined to yield neural network outputs close to the desired set of target outputs and then providing signals characteristic of an industrial process and comparing the neural network output to the industrial process signals to evaluate the operating state of the industrial process. 33 figs.

Very High Reflectivity Supermirrors And Their Applications

NASA Astrophysics Data System (ADS)

Mezei, F.

1989-01-01

Very high reflectivity (some 95 % or better) supermirrors, with cut-off angles up to 2 times the critical angle of Ni coated simple total reflection neutron mirrors, can be produced using well established conventional deposition techniques. This performance makes applications involving multiple reflections and transmission geometries feasible, which in turn allow us to use more sophisticated neutron optical systems in order to optimize performance and minimize the amount a scarce supermirrors required. A key feature of several of these novel systems is the distribution of tasks between the several optical components achieving the desired performance by multiple action. The design and characteristics of a series of novel applications, such as polarizing cavities, collimators and guides, non-polarizing guides, beam compressors, deflectors and splitters (most of them tested or being implemented) are the main subjects of the present paper.

The Influence of Power and Intimacy Sexual Motives on Sexual Position Preference Among Men Who Have Sex with Men in China.

PubMed

Xu, Yin; Zheng, Yong

2018-01-01

We examined the sexual motives underlying sexual self-labels among Chinese men who have sex with men. A total of 60 bottoms, 120 versatiles, and 48 tops participated in a Web-based survey. Our results showed that tops were more likely to desire exerting power over their partners during sex, while bottoms were more likely to desire being overpowered by their partners. There were no significant sexual self-label differences in the sexual motives of wanting intimacy and the desire for pleasure. The intimacy and power ratings differed across sexual activities and sex positions. There was a tendency for sexual positions in which the performer was facing the receiver to be rated as more intimate than those in which the performer was facing away from the receiver, and for individuals who preferred to be insertive to feel more powerful in sexual positions in which their partner was kneeling down or standing than those in which their partner was sitting or lying down. Tops were significantly more likely than bottoms to engage in insertive sexual positions, while bottoms were significantly more likely to engage in receptive sexual positions. Both tops and bottoms were more likely to engage in the corresponding insertive/receptive position when the insertive position was rated as more powerful than the receptive position. Our results suggest that the concordance between sexual self-labels and sexual position preferences may rely on the power difference between the insertive and receptive positions in addition to body characteristics.

Paying for performance: Performance incentives increase desire for the reward object.

PubMed

Hur, Julia D; Nordgren, Loran F

2016-09-01

The current research examines how exposure to performance incentives affects one's desire for the reward object. We hypothesized that the flexible nature of performance incentives creates an attentional fixation on the reward object (e.g., money), which leads people to become more desirous of the rewards. Results from 5 laboratory experiments and 1 large-scale field study provide support for this prediction. When performance was incentivized with monetary rewards, participants reported being more desirous of money (Study 1), put in more effort to earn additional money in an ensuing task (Study 2), and were less willing to donate money to charity (Study 4). We replicated the result with nonmonetary rewards (Study 5). We also found that performance incentives increased attention to the reward object during the task, which in part explains the observed effects (Study 6). A large-scale field study replicated these findings in a real-world setting (Study 7). One laboratory experiment failed to replicate (Study 3). (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Tracking performance and cycle slipping in the all-digital symbol synchronizer loop of the block 5 receiver

NASA Astrophysics Data System (ADS)

Aung, M.

1992-11-01

Computer simulated noise performance of the symbol synchronizer loop (SSL) in the Block 5 receiver is compared with the theoretical noise performance. Good agreement is seen at the higher loop SNR's (SNR(sub L)'s), with gradual degradation as the SNR(sub L) is decreased. For the different cases simulated, cycle slipping is observed (within the simulation time of 10(exp 4) seconds) at SNR(sub L)'s below different thresholds, ranging from 6 to 8.5 dB, comparable to that of a classical phase-locked loop. An important point, however, is that to achieve the desired loop SNR above the seemingly low threshold to avoid cycle slipping, a large data-to-loop-noise power ratio, P(sub D)/(N(sub 0)B(sub L)), is necessary (at least 13 dB larger than the desired SNR(sub L) in the optimum case and larger otherwise). This is due to the large squaring loss (greater than or equal to 13 dB) inherent in the SSL. For the special case of symbol rates approximately equaling the loop update rate, a more accurate equivalent model accounting for an extra loop update period delay (characteristic of the SSL phase detector design) is derived. This model results in a more accurate estimation of the noise-equivalent bandwidth of the loop.

Tracking performance and cycle slipping in the all-digital symbol synchronizer loop of the block 5 receiver

NASA Technical Reports Server (NTRS)

Aung, M.

1992-01-01

Computer simulated noise performance of the symbol synchronizer loop (SSL) in the Block 5 receiver is compared with the theoretical noise performance. Good agreement is seen at the higher loop SNR's (SNR(sub L)'s), with gradual degradation as the SNR(sub L) is decreased. For the different cases simulated, cycle slipping is observed (within the simulation time of 10(exp 4) seconds) at SNR(sub L)'s below different thresholds, ranging from 6 to 8.5 dB, comparable to that of a classical phase-locked loop. An important point, however, is that to achieve the desired loop SNR above the seemingly low threshold to avoid cycle slipping, a large data-to-loop-noise power ratio, P(sub D)/(N(sub 0)B(sub L)), is necessary (at least 13 dB larger than the desired SNR(sub L) in the optimum case and larger otherwise). This is due to the large squaring loss (greater than or equal to 13 dB) inherent in the SSL. For the special case of symbol rates approximately equaling the loop update rate, a more accurate equivalent model accounting for an extra loop update period delay (characteristic of the SSL phase detector design) is derived. This model results in a more accurate estimation of the noise-equivalent bandwidth of the loop.

The Effects of Sex and Gender-Role Characteristics on Facets of Sociosexuality in Heterosexual Young Adults.

PubMed

Rammsayer, Thomas H; Borter, Natalie; Troche, Stefan J

2017-02-01

The present study was designed to systematically investigate the functional relationships among biological sex; masculine and feminine gender-role characteristics; and sociosexual behavior, attitude toward, and desire for uncommitted casual sex as three facets of sociosexual orientation. For this purpose, facets of sociosexuality were assessed by the Revised Sociosexual Orientation Inventory (SOI-R) and masculine and feminine gender-role characteristics were assessed by a revised German version of the Bem Sex-Role Inventory in 499 male and 958 female heterosexual young adults. Confirmatory factor analysis (CFA) and structural equation modeling (SEM) revealed differential mediating effects of masculine and feminine gender-role characteristics on the relationship between biological sex and the three facets of sociosexual orientation. Sociosexual behavior was shown to be primarily controlled by an individual's level of masculine gender-role characteristics irrespective of biological sex. Sociosexual desire was identified as being a sole function of biological sex with no indication for any effect of masculine or feminine gender-role characteristics, while sociosexual attitude was influenced by biological sex as well as by masculine and feminine gender-role characteristics to about the same extent.

Method and apparatus for calibrating a display using an array of cameras

NASA Technical Reports Server (NTRS)

Johnson, Michael J. (Inventor); Chen, Chung-Jen (Inventor); Chandrasekhar, Rajesh (Inventor)

2001-01-01

The present invention overcomes many of the disadvantages of the prior art by providing a display that can be calibrated and re-calibrated with a minimal amount of manual intervention. To accomplish this, the present invention provides one or more cameras to capture an image that is projected on a display screen. In one embodiment, the one or more cameras are placed on the same side of the screen as the projectors. In another embodiment, an array of cameras is provided on either or both sides of the screen for capturing a number of adjacent and/or overlapping capture images of the screen. In either of these embodiments, the resulting capture images are processed to identify any non-desirable characteristics including any visible artifacts such as seams, bands, rings, etc. Once the non-desirable characteristics are identified, an appropriate transformation function is determined. The transformation function is used to pre-warp the input video signal to the display such that the non-desirable characteristics are reduced or eliminated from the display. The transformation function preferably compensates for spatial non-uniformity, color non-uniformity, luminance non-uniformity, and/or other visible artifacts.

Recognizing and engineering digital-like logic gates and switches in gene regulatory networks.

PubMed

Bradley, Robert W; Buck, Martin; Wang, Baojun

2016-10-01

A central aim of synthetic biology is to build organisms that can perform useful activities in response to specified conditions. The digital computing paradigm which has proved so successful in electrical engineering is being mapped to synthetic biological systems to allow them to make such decisions. However, stochastic molecular processes have graded input-output functions, thus, bioengineers must select those with desirable characteristics and refine their transfer functions to build logic gates with digital-like switching behaviour. Recent efforts in genome mining and the development of programmable RNA-based switches, especially CRISPRi, have greatly increased the number of parts available to synthetic biologists. Improvements to the digital characteristics of these parts are required to enable robust predictable design of deeply layered logic circuits. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

LAC indicators: an evaluation of progress and list of proposed indicators

Treesearch

Alan E. Watson; David N. Cole

1992-01-01

One of the most critical, and difficult, steps in the Limits of Acceptable Change (LAC) process is the selection of indicators. To help with this step, this paper (I) briefly reviews some desirable characteristics of indicators and (2) lists indicators that have been proposed or adopted in LAC plans. From a comparison of this list of indicators and desirable...

Eigenspace Design of Helicopter Flight Control Systems

DTIC Science & Technology

1990-11-01

Attitude Changes ......... 44 2.6 Yaw Cross Coupling Criteria . ............................................... 45 I 4. i Definition of the Rigid Body...laws. The methodology detailed in this report allows the designer to synthesize control laws which result in desirable response types such as attitude ...it is simple to relate the desired frequency response characteristics to the natural frequencies and damping factors or the time constants of the

Core-in-shell sorbent for hot coal gas desulfurization

DOEpatents

Wheelock, Thomas D.; Akiti, Jr., Tetteh T.

2004-02-10

A core-in-shell sorbent is described herein. The core is reactive to the compounds of interest, and is preferably calcium-based, such as limestone for hot gas desulfurization. The shell is a porous protective layer, preferably inert, which allows the reactive core to remove the desired compounds while maintaining the desired physical characteristics to withstand the conditions of use.

Investigation of the Behavioral Characteristics of Dogs Purpose-Bred and Prepared to Perform Vapor Wake® Detection of Person-Borne Explosives.

PubMed

Lazarowski, Lucia; Haney, Pamela Sue; Brock, Jeanne; Fischer, Terry; Rogers, Bart; Angle, Craig; Katz, Jeffrey S; Waggoner, L Paul

2018-01-01

Specialized detector dogs are increasingly being utilized for the detection of modern threats. The Vapor Wake ® (VW) dog was developed to create a dog phenotype ideally suited for detecting hand-carried and body-worn explosives. VW dogs (VWDs) are trained to sample and alert to target odors in the aerodynamic wakes of moving persons, which entrains vapor and small particles from the person. The behavioral characteristics necessary for dogs to be successfully trained and employed for the application of VW are a distinct subset of the desired general characteristics of dogs used for detection tasks due to the dynamic nature of moving targets. The purpose of this study was to examine the behavioral characteristics of candidate detector dogs to determine the particular qualities that set apart VW-capable dogs from others. We assessed 146 candidate detector dogs from a VW breeding and training program. Dogs received identical puppy development and foundational odor training and underwent performance evaluations at 3, 6, 10, and 12 months old, after which they were sold for service. Dogs were categorized based on their final outcome of the training program, independently determined by private vendors, corresponding to three groups: dogs successfully sold for VW, dogs sold for standard explosives detection, and dogs that failed to be placed in any type of detector dog service (Washouts). Comparisons of behavioral evaluations between the groups were made across domains pertaining to search-related behaviors (Performance), reactions to novel stimuli (Environmental), and overall ease of learning new tasks (Trainability). Comparisons were also made at each evaluation to determine any early emergence of differences. VWDs scored significantly higher on Performance characteristics compared to standard explosives detection dogs (EDDs) and Washouts. However, Environmental characteristics did not differentiate VWDs from EDDs, though scores on these measures were significantly lower in the Washouts. Furthermore, differences between groups emerged as early as 3 and 6 months for select measures. We describe the behavioral characteristics targeted for selection in developing the VW phenotype and discuss the relative merit and degree of expression of those characteristics in the success of dogs bred and trained for the VW application.

Social and Behavioral Characteristics of Chinese Only Children and Its Research Concern.

ERIC Educational Resources Information Center

Chen, Jie-Qi; Goldsmith, Lynn T.

This study reviews the literature on the social and behavioral characteristics of only children in China. Of 16 studies that reported differences in the characteristics of only and non-only children, only 2 indicated that only children exhibited more socially desirable behaviors than did non-only children. The remaining studies reported that,…

Executive Function and the Development of Belief-Desire Psychology

ERIC Educational Resources Information Center

Rakoczy, Hannes

2010-01-01

In two studies children's performance on tasks requiring the ascription of beliefs and desires was investigated in relation to their executive function. Study 1 (n = 80) showed that 3- and 4-year-olds were more proficient at ascribing subjective, mutually incompatible desires and desire-dependent emotions to two persons than they were at ascribing…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salama, A.; Mikhail, M.

Comprehensive software packages have been developed at the Western Research Centre as tools to help coal preparation engineers analyze, evaluate, and control coal cleaning processes. The COal Preparation Software package (COPS) performs three functions: (1) data handling and manipulation, (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modeling, evaluation of density and size partition characteristics and attrition curves, and (3) generation of graphics output. The Separation ChARacteristics Estimation software packages (SCARE) are developed to balance raw density or size separation data. The cases of density and size separation data are considered. Themore » generated balanced data can take the balanced or normalized forms. The scaled form is desirable for direct determination of the partition functions (curves). The raw and generated separation data are displayed in tabular and/or graphical forms. The computer softwares described in this paper are valuable tools for coal preparation plant engineers and operators for evaluating process performance, adjusting plant parameters, and balancing raw density or size separation data. These packages have been applied very successfully in many projects carried out by WRC for the Canadian coal preparation industry. The software packages are designed to run on a personal computer (PC).« less

Can soft biometric traits assist user recognition?

NASA Astrophysics Data System (ADS)

Jain, Anil K.; Dass, Sarat C.; Nandakumar, Karthik

2004-08-01

Biometrics is rapidly gaining acceptance as the technology that can meet the ever increasing need for security in critical applications. Biometric systems automatically recognize individuals based on their physiological and behavioral characteristics. Hence, the fundamental requirement of any biometric recognition system is a human trait having several desirable properties like universality, distinctiveness, permanence, collectability, acceptability, and resistance to circumvention. However, a human characteristic that possesses all these properties has not yet been identified. As a result, none of the existing biometric systems provide perfect recognition and there is a scope for improving the performance of these systems. Although characteristics like gender, ethnicity, age, height, weight and eye color are not unique and reliable, they provide some information about the user. We refer to these characteristics as "soft" biometric traits and argue that these traits can complement the identity information provided by the primary biometric identifiers like fingerprint and face. This paper presents the motivation for utilizing soft biometric information and analyzes how the soft biometric traits can be automatically extracted and incorporated in the decision making process of the primary biometric system. Preliminary experiments were conducted on a fingerprint database of 160 users by synthetically generating soft biometric traits like gender, ethnicity, and height based on known statistics. The results show that the use of additional soft biometric user information significantly improves (approximately 6%) the recognition performance of the fingerprint biometric system.

Investigation of the Impedance Characteristic of Human Arm for Development of Robots to Cooperate with Humans

NASA Astrophysics Data System (ADS)

Rahman, Md. Mozasser; Ikeura, Ryojun; Mizutani, Kazuki

In the near future many aspects of our lives will be encompassed by tasks performed in cooperation with robots. The application of robots in home automation, agricultural production and medical operations etc. will be indispensable. As a result robots need to be made human-friendly and to execute tasks in cooperation with humans. Control systems for such robots should be designed to work imitating human characteristics. In this study, we have tried to achieve these goals by means of controlling a simple one degree-of-freedom cooperative robot. Firstly, the impedance characteristic of the human arm in a cooperative task is investigated. Then, this characteristic is implemented to control a robot in order to perform cooperative task with humans. A human followed the motion of an object, which is moved through desired trajectories. The motion is actuated by the linear motor of the one degree-of-freedom robot system. Trajectories used in the experiments of this method were minimum jerk (the rate of change of acceleration) trajectory, which was found during human and human cooperative task and optimum for muscle movement. As the muscle is mechanically analogous to a spring-damper system, a simple second-order equation is used as models for the arm dynamics. In the model, we considered mass, stiffness and damping factor. Impedance parameter is calculated from the position and force data obtained from the experiments and based on the “Estimation of Parametric Model”. Investigated impedance characteristic of human arm is then implemented to control a robot, which performed cooperative task with human. It is observed that the proposed control methodology has given human like movements to the robot for cooperating with human.

Retail Lamps Study 3.1: Dimming, Flicker, and Power Quality Characteristics of LED A Lamps

DOE Office of Scientific and Technical Information (OSTI.GOV)

Royer, Michael P.; Poplawski, Michael E.; Brown, Charles C.

2014-12-01

To date, all three reports in the retail lamps series have focused on basic performance parameters, such as lumen output, efficacy, and color quality. This report goes a step further, examining the photoelectric characteristics (i.e., dimming and flicker) of a subset of lamps from CALiPER Retails Lamps Study 3. Specifically, this report focuses on the dimming, power quality, and flicker characteristics of 14 LED A lamps, as controlled by four different retail-available dimmers. The results demonstrate notable variation across the various lamps, but little variation between the four dimmers. Overall, the LED lamps: ~tended to have higher relative light outputmore » compared to the incandescent and halogen benchmark at the same dimmer output signal (RMS voltage). The lamps’ dimming curves (i.e., the relationship between control signal and relative light output) ranged from linear to very similar to the square-law curve typical of an incandescent lamp. ~generally exhibited symmetrical behavior—the same dimming curve—when measured proceeding from maximum to minimum or minimum to maximum control signal. ~mostly dimmed below 10% of full light output, with some exceptions for specific lamp and dimmer combinations ~exhibited a range of flicker characteristics, with many comparing favorably to the level typical of a magnetically-ballasted fluorescent lamp through at least a majority of the dimming range. ~ always exceeded the relative (normalized) efficacy over the dimming range of the benchmark lamps, which rapidly decline in efficacy when they are dimmed. This report generally does not attempt to rank the performance of one product compared to another, but instead focuses on the collective performance of the group versus conventional incandescent or halogen lamps, the performance of which is likely to be the baseline for a majority of consumers. Undoubtedly, some LED lamps perform better—or more similar to conventional lamps—than others. Some perform desirably for one characteristic, but not others. Consumers (and specifiers) may have a hard time distinguishing better-performing lamps from one another; at this time, physical experimentation is likely the best evaluation tool.« less

[Characteristics of the clients in a geriatric intermediate care facility located in the suburbs of an urban area and factors related to the discharge destinations desired by family caregivers].

PubMed

Watanabe, M; Kono, K; Nishiura, K; Miyata, K; Saito, M

1999-01-01

Among the clients in a geriatric intermediate care facility located in the suburbs of Osaka and their family caregivers (72 subjects), the characteristics of the clients and their caregivers, and the discharge destination desired by their family caregivers were investigated, and the associated factors were evaluated. 1. Characteristics of the clients. The clients were elderly females with a low degree of independence, and dementia was observed in about 60% of them. The clients had a relatively large number of children, but many of them lived alone before admission. The rate of admission from hospitals was high (54%), and that of discharge to hospitals was also high (50%). Sixty-seven percent of the clients stayed for a long duration of over 6 months. 2. Conditions of the family caregivers. Most of the family caregivers were daughters or daughters-in-law, and considered themselves to be healthy. Sixty-three percent of the caregivers had jobs. However, most of the caregivers did not have sub-caregiver. 3. Factors related to the discharge destination desired by family caregivers. Not many family caregivers (19.4%) wanted them to go back to their homes after discharge, but their preferred discharge destinations were home (19.4%), hospitals (55.5%), and nursing homes (25.1%). The caregivers of single household clients often desired a nursing home as the discharge destination, and those of the clients from a 2- or 3-generation household often desired a hospital. The factors related to the discharge destination desired by client's family caregivers were that the client not show dementia, the job of the caregiver was a part-time job, there was a sub-caregiver, and the client had the experience of home public health nursing visits. This study showed, the percentage of the clients discharged from the geriatric intermediate care facility to their homes was low, and that of the family caregivers who desired their home as the discharge destination was also low. However, the results suggested that leading the discharge destination to the client's home is possible if social resources are provided such as the use of public health nursing services.

Combined optimization of image-gathering and image-processing systems for scene feature detection

NASA Technical Reports Server (NTRS)

Halyo, Nesim; Arduini, Robert F.; Samms, Richard W.

1987-01-01

The relationship between the image gathering and image processing systems for minimum mean squared error estimation of scene characteristics is investigated. A stochastic optimization problem is formulated where the objective is to determine a spatial characteristic of the scene rather than a feature of the already blurred, sampled and noisy image data. An analytical solution for the optimal characteristic image processor is developed. The Wiener filter for the sampled image case is obtained as a special case, where the desired characteristic is scene restoration. Optimal edge detection is investigated using the Laplacian operator x G as the desired characteristic, where G is a two dimensional Gaussian distribution function. It is shown that the optimal edge detector compensates for the blurring introduced by the image gathering optics, and notably, that it is not circularly symmetric. The lack of circular symmetry is largely due to the geometric effects of the sampling lattice used in image acquisition. The optimal image gathering optical transfer function is also investigated and the results of a sensitivity analysis are shown.

Organizational culture in the primary healthcare setting of Cyprus

PubMed Central

2013-01-01

Background The concept of organizational culture is important in understanding the behaviour of individuals in organizations as they manage external demands and internal social changes. Cyprus healthcare system is under restructuring and soon a new healthcare scheme will be implemented starting at the Primary Healthcare (PHC) level. The aim of the study was to investigate the underlying culture encountered in the PHC setting of Cyprus and to identify possible differences in desired and prevailing cultures among healthcare professionals. Methods The population of the study included all general practitioners (GPs) and nursing staff working at the 42 PHC centres throughout the island. The shortened version of the Organizational Culture Profile questionnaire comprising 28 statements on organizational values was used in the study. The instrument was already translated and validated in Greek and cross-cultural adaptation was performed. Participants were required to indicate the organization’s characteristic cultural values orientation along a five-point Likert scale ranging from “Very Much = 1” to “Not at all= 5”. Statistical analysis was performed using SPSS 16.0. Student t-test was used to compare means between two groups of variables whereas for more than two groups analysis of variance (ANOVA) was applied. Results From the total of 306 healthcare professionals, 223 participated in the study (72.9%). The majority of participants were women (75.3%) and mean age was 42.6 ± 10.7 years. Culture dimension “performance orientation” was the desired culture among healthcare professionals (mean: 1.39 ± 0.45). “Supportiveness” and “social responsibility” were the main cultures encountered in PHC (means: 2.37 ± 0.80, 2.38 ± 0.83). Statistical significant differences were identified between desired and prevailing cultures for all culture dimensions (p= 0.000). Conclusions This was the first study performed in Cyprus assessing organizational culture in the PHC setting. In the forthcoming health system reform, healthcare professionals will face challenges both at organizational level and professional status. Results of the study can serve as background knowledge for leaders and policy makers who seek interventions to improve performance before the implementation of a new national healthcare scheme. PMID:23522058

Organizational culture in the primary healthcare setting of Cyprus.

PubMed

Zachariadou, Theodora; Zannetos, Savvas; Pavlakis, Andreas

2013-03-24

The concept of organizational culture is important in understanding the behaviour of individuals in organizations as they manage external demands and internal social changes. Cyprus healthcare system is under restructuring and soon a new healthcare scheme will be implemented starting at the Primary Healthcare (PHC) level. The aim of the study was to investigate the underlying culture encountered in the PHC setting of Cyprus and to identify possible differences in desired and prevailing cultures among healthcare professionals. The population of the study included all general practitioners (GPs) and nursing staff working at the 42 PHC centres throughout the island. The shortened version of the Organizational Culture Profile questionnaire comprising 28 statements on organizational values was used in the study. The instrument was already translated and validated in Greek and cross-cultural adaptation was performed. Participants were required to indicate the organization's characteristic cultural values orientation along a five-point Likert scale ranging from "Very Much = 1" to "Not at all= 5". Statistical analysis was performed using SPSS 16.0. Student t-test was used to compare means between two groups of variables whereas for more than two groups analysis of variance (ANOVA) was applied. From the total of 306 healthcare professionals, 223 participated in the study (72.9%). The majority of participants were women (75.3%) and mean age was 42.6 ± 10.7 years. Culture dimension "performance orientation" was the desired culture among healthcare professionals (mean: 1.39 ± 0.45). "Supportiveness" and "social responsibility" were the main cultures encountered in PHC (means: 2.37 ± 0.80, 2.38 ± 0.83). Statistical significant differences were identified between desired and prevailing cultures for all culture dimensions (p= 0.000). This was the first study performed in Cyprus assessing organizational culture in the PHC setting. In the forthcoming health system reform, healthcare professionals will face challenges both at organizational level and professional status. Results of the study can serve as background knowledge for leaders and policy makers who seek interventions to improve performance before the implementation of a new national healthcare scheme.

"Masculinity, Femininity, Achievement Conflicts and Health."

ERIC Educational Resources Information Center

Olds, Debra Eaton

The objective of this study is to measure achievement motivation in terms of psychological masculinity and femininity rather than in terms of biological gender. The terms, psychological masculinity and femininity, refer to sets of characteristics desirable for both sexes. Masculine characteristics include independence, self-confidence,…

Relationship of a desire of thinness and eating behavior among Japanese underweight female students.

PubMed

Mase, Tomoki; Miyawaki, Chiemi; Kouda, Katsuyasu; Fujita, Yuki; Ohara, Kumiko; Nakamura, Harunobu

2013-06-01

We conducted a questionnaire survey among Japanese female students to explore the influence of a desire for thinness and dietary behaviors on the development of eating disorders. Self-reported measures of socio-demographic characteristics, body weight perception, height and weight, and dietary and exercise behavior were completed by 631 female university students at 6 universities in Kyoto, Japan. Many students had a desire for thinness (underweight students, 51.7 %; normal-weight students, 88.8 %), whereas ideal weight and body mass index were lower in the students with a desire for thinness than the students without a desire for thinness, and were also lower in the underweight students than the normal-weight students. The eating attitude test (EAT-26) scores of underweight students with a desire for thinness were higher than those of the normal-weight students with a desire for thinness. As a result of a logistic regression analysis, underweight, desire for thinness, and experience with weight control were positively associated with eating problems. Further, the association of eating problems increased along with the increase in the number of factors (underweight, desire for thinness, and experience with weight control). These results indicate that underweight females have strong associations with eating problems.

Display screen and method of manufacture therefor

NASA Technical Reports Server (NTRS)

Dubin, Matthew B. (Inventor); Larson, Brent D. (Inventor)

2002-01-01

A screen assembly that combines an angle re-distributing prescreen with a conventional diffusion screen. The prescreen minimizes or eliminates the sensitivity of the screen assembly to projector location. The diffusion screen provides other desirable screen characteristics. Compatible screen structures, along with methods for fabricating high resolution prescreens and methods and devices for maintaining the desired relationship between the prescreen and the diffusion screen are contemplated.

Advanced Communication for Wireless Sensor Networks

DTIC Science & Technology

2016-08-22

characteristic peaks of the PZT crystallography and the presence of non-desired secondary phases. Regarding the spinel thin film, a new sol gel process...particles with the desired crystallography were obtained. As shown in Figure 21 (left), the particle morphology and size can be seen using TEM...film. The crystallography of the films was characterized at different annealing temperatures in order to determine the crystallization kinetics. It

Towards Transparent Throughput Elasticity for IaaS Cloud Storage: Exploring the Benefits of Adaptive Block-Level Caching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nicolae, Bogdan; Riteau, Pierre; Keahey, Kate

Storage elasticity on IaaS clouds is a crucial feature in the age of data-intensive computing, especially when considering fluctuations of I/O throughput. This paper provides a transparent solution that automatically boosts I/O bandwidth during peaks for underlying virtual disks, effectively avoiding over-provisioning without performance loss. The authors' proposal relies on the idea of leveraging short-lived virtual disks of better performance characteristics (and thus more expensive) to act during peaks as a caching layer for the persistent virtual disks where the application data is stored. Furthermore, they introduce a performance and cost prediction methodology that can be used both independently tomore » estimate in advance what trade-off between performance and cost is possible, as well as an optimization technique that enables better cache size selection to meet the desired performance level with minimal cost. The authors demonstrate the benefits of their proposal both for microbenchmarks and for two real-life applications using large-scale experiments.« less

The Correlates of Similarity Estimates are Often Misleadingly Positive: The Nature and Scope of the Problem, and Some Solutions

PubMed Central

Wood, Dustin; Furr, R. Michael

2015-01-01

Research on similarity constructs (e.g., dyadic similarity, personality stability; judgment agreement and accuracy) frequently find them to be associated with positive outcomes. However, a methodological pitfall associated with common ‘overall similarity’ indices, which we term the normative-desirability confound (NDC), will regularly result in similarity constructs apparently having more positive effects than they do in reality. In essence, when an individual is estimated to be similar to another person by common indices, this will strongly indicate that the individual has desirable characteristics. Consequently, the correlates of overall similarity indices can often be interpreted as indicating the beneficial effects of having desirable characteristics, without needing to attribute any additional salutary effect to similarity. We show that this confound is present in overall similarity estimates for a wide range of constructs (e.g., personality traits, attitudes, emotions, behaviors, values), how it can be accounted for, and discuss larger implications for our understanding of similarity constructs. PMID:25896284

Gluten-free is not enough--perception and suggestions of celiac consumers.

PubMed

do Nascimento, Amanda Bagolin; Fiates, Giovanna Medeiros Rataichesck; dos Anjos, Adilson; Teixeira, Evanilda

2014-06-01

The present study investigated the perceptions of individuals with celiac disease about gluten-free (GF) products, their consumer behavior and which product is the most desired. A survey was used to collect information. Descriptive analysis, χ² tests and Multiple Logistic Regressions were conducted. Ninety-one questionnaires were analyzed. Limited variety and availability, the high price of products and the social restrictions imposed by the diet were the factors that caused the most dissatisfaction and difficulty. A total of 71% of the participants confirmed having moderate to high difficulty finding GF products. The logistic regression identified a significant relationship between dissatisfaction, texture and variety (p < 0.05) and between variety and difficulty of finding GF products (p < 0.05). The sensory characteristics were the most important variables considered for actual purchases. Bread was the most desired product. The participants were dissatisfaction with GF products. The desire for bread with better sensory characteristics reinforces the challenge to develop higher quality baking products.

Three- and Four-Year-Old Children's Ability to Use Desire- and Belief-Based Reasoning.

ERIC Educational Resources Information Center

Cassidy, Kimberly Wright

1998-01-01

This study investigated the relationship of 3-year olds' reliance on desire when predicting behavior and their performance on false-belief tasks. Results suggested that young children may use the desires of the agent, rather than their own desires, to predict behavior in standard false-belief paradigms. Older preschoolers also have difficulty…

Analysis of the packet formation process in packet-switched networks

NASA Astrophysics Data System (ADS)

Meditch, J. S.

Two new queueing system models for the packet formation process in packet-switched telecommunication networks are developed, and their applications in process stability, performance analysis, and optimization studies are illustrated. The first, an M/M/1 queueing system characterization of the process, is a highly aggregated model which is useful for preliminary studies. The second, a marked extension of an earlier M/G/1 model, permits one to investigate stability, performance characteristics, and design of the packet formation process in terms of the details of processor architecture, and hardware and software implementations with processor structure and as many parameters as desired as variables. The two new models together with the earlier M/G/1 characterization span the spectrum of modeling complexity for the packet formation process from basic to advanced.

A Review of Metal Injection Molding- Process, Optimization, Defects and Microwave Sintering on WC-Co Cemented Carbide

NASA Astrophysics Data System (ADS)

Shahbudin, S. N. A.; Othman, M. H.; Amin, Sri Yulis M.; Ibrahim, M. H. I.

2017-08-01

This article is about a review of optimization of metal injection molding and microwave sintering process on tungsten cemented carbide produce by metal injection molding process. In this study, the process parameters for the metal injection molding were optimized using Taguchi method. Taguchi methods have been used widely in engineering analysis to optimize the performance characteristics through the setting of design parameters. Microwave sintering is a process generally being used in powder metallurgy over the conventional method. It has typical characteristics such as accelerated heating rate, shortened processing cycle, high energy efficiency, fine and homogeneous microstructure, and enhanced mechanical performance, which is beneficial to prepare nanostructured cemented carbides in metal injection molding. Besides that, with an advanced and promising technology, metal injection molding has proven that can produce cemented carbides. Cemented tungsten carbide hard metal has been used widely in various applications due to its desirable combination of mechanical, physical, and chemical properties. Moreover, areas of study include common defects in metal injection molding and application of microwave sintering itself has been discussed in this paper.

Design optimization of electric vehicle battery cooling plates for thermal performance

NASA Astrophysics Data System (ADS)

Jarrett, Anthony; Kim, Il Yong

The performance of high-energy battery cells utilized in electric vehicles (EVs) is greatly improved by adequate temperature control. An efficient thermal management system is also desirable to avoid diverting excessive power from the primary vehicle functions. In a battery cell stack, cooling can be provided by including cooling plates: thin metal fabrications which include one or more internal channels through which a coolant is pumped. Heat is conducted from the battery cells into the cooling plate, and transported away by the coolant. The operating characteristics of the cooling plate are determined in part by the geometry of the channel; its route, width, length, etc. In this study, a serpentine-channel cooling plate is modeled parametrically and its characteristics assessed using computational fluid dynamics (CFD). Objective functions of pressure drop, average temperature, and temperature uniformity are defined and numerical optimization is carried out by allowing the channel width and position to vary. The optimization results indicate that a single design can satisfy both pressure and average temperature objectives, but at the expense of temperature uniformity.

Characteristic analysis of diaphragm-type transducer that is thick relative to its size

NASA Astrophysics Data System (ADS)

Ishiguro, Yuya; Zhu, Jing; Tagawa, Norio; Okubo, Tsuyoshi; Okubo, Kan

2017-07-01

In recent years, high-performance piezoelectric micromachined ultrasonic transducers (PMUTs) have been fabricated by micro electro mechanical systems (MEMS) technology. For high-resolution imaging, it is important to broaden the frequency bandwidth. By reducing the diaphragm size to increase the resonance frequency, the film thickness becomes relatively larger and hence the transmitting and receiving characteristics may different from those of a usual thin diaphragm. In this study, we examine the performance of a square-diaphragm-type lead zirconate titanate (PZT) transducer through simulations. To realize the desired resonance frequency of 20 MHz, firstly, the diaphragm size and the thickness of the layers of PZT and Si constituting a PMUT are examined, and then, three PZT/Si models with different thicknesses are selected. Subsequently, using the models, we analyze the transmitting efficiency, transmitting bandwidth, receiving sensitivity (piezoelectric voltage/electric charge), and receiving bandwidth using an FEM simulator. It is found that the proposed models can transmit ultrasound independently of the diaphragm vibration and have wide bandwidth of the receiving frequency as compared with that of a typical PMUT.

Evolving Requirements for Magnetic Tape Data Storage Systems

NASA Technical Reports Server (NTRS)

Gniewek, John J.

1996-01-01

Magnetic tape data storage systems have evolved in an environment where the major applications have been back-up/restore, disaster recovery, and long term archive. Coincident with the rapidly improving price-performance of disk storage systems, the prime requirements for tape storage systems have remained: (1) low cost per MB, (2) a data rate balanced to the remaining system components. Little emphasis was given to configuring the technology components to optimize retrieval of the stored data. Emerging new applications such as network attached high speed memory (HSM), and digital libraries, place additional emphasis and requirements on the retrieval of the stored data. It is therefore desirable to consider the system to be defined both by STorage And Retrieval System (STARS) requirements. It is possible to provide comparative performance analysis of different STARS by incorporating parameters related to (1) device characteristics, and (2) application characteristics in combination with queuing theory analysis. Results of these analyses are presented here in the form of response time as a function of system configuration for two different types of devices and for a variety of applications.

Comparing multiple statistical methods for inverse prediction in nuclear forensics applications

DOE PAGES

Lewis, John R.; Zhang, Adah; Anderson-Cook, Christine Michaela

2017-10-29

Forensic science seeks to predict source characteristics using measured observables. Statistically, this objective can be thought of as an inverse problem where interest is in the unknown source characteristics or factors ( X) of some underlying causal model producing the observables or responses (Y = g ( X) + error). Here, this paper reviews several statistical methods for use in inverse problems and demonstrates that comparing results from multiple methods can be used to assess predictive capability. Motivation for assessing inverse predictions comes from the desired application to historical and future experiments involving nuclear material production for forensics research inmore » which inverse predictions, along with an assessment of predictive capability, are desired.« less

Comparing multiple statistical methods for inverse prediction in nuclear forensics applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, John R.; Zhang, Adah; Anderson-Cook, Christine Michaela

Forensic science seeks to predict source characteristics using measured observables. Statistically, this objective can be thought of as an inverse problem where interest is in the unknown source characteristics or factors ( X) of some underlying causal model producing the observables or responses (Y = g ( X) + error). Here, this paper reviews several statistical methods for use in inverse problems and demonstrates that comparing results from multiple methods can be used to assess predictive capability. Motivation for assessing inverse predictions comes from the desired application to historical and future experiments involving nuclear material production for forensics research inmore » which inverse predictions, along with an assessment of predictive capability, are desired.« less

A program to evaluate a control system based on feedback of aerodynamic pressure differentials, part 1

NASA Technical Reports Server (NTRS)

Hrabak, R. R.; Levy, D. W.; Finn, P.; Roskam, J.

1981-01-01

The use of pressure differentials in a flight control system was evaluated. The pressure profile around the test surface was determined using two techniques: (1) windtunnel data (actual); and (2) NASA/Langley Single Element Airfoil Computer Program (theoretical). The system designed to evaluate the concept of using pressure differentials is composed of a sensor drive and power amplifiers, actuator, position potentiometer, and a control surface. The characteristics (both desired and actual) of the system and each individual component were analyzed. The desired characteristics of the system as a whole are given. The flight control system developed, the testing procedures and data reduction methods used, and theoretical frequency response analysis are described.

Effects of stick dynamics on helicopter flying qualities

NASA Technical Reports Server (NTRS)

Watson, Douglas C.; Schroeder, Jeffery A.

1990-01-01

An experiment that investigated the influence of typical helicopter force-feel system dynamics on roll-axis handling qualities was conducted in concurrent ground and inflight simulations. Variations in lateral control natural frequency and damping ratio, effected by changes in inertia and damping, were evaluated in a disturbance-rejection task. Pilot ratings indicated a preference for low-inertia feel systems, although measured performance was relatively constant over the range of stick characteristics. Force-sensing was compared with position sensing as the input to the control system. Force-sensing improved performance but did not improve pilot ratings. Overall, the results indicated that control-stick dynamics, at least within a reasonable range, did not have a significant effect on pilot-vehicle performance. However, the physical effort required to maintain a desired pilot/manipulator bandwidth became objectionable as the stick inertia increased beyond 5-7 lbm, which was reflected in the pilot ratings and comments.

High-performance fiber optic link for ECM antenna remoting

NASA Astrophysics Data System (ADS)

Edge, Colin; Burgess, John W.; Wale, Michael J.; Try, Nicholas W.

1998-11-01

The ability to remotely radiate microwave signals has become an essential feature of modern electronic counter-measures (ECM) systems. The use of fiber optics allows remote microwave links to be constructed which have very low propagation loss and dispersion, are very flexible and light in weight, and have a high degree of immunity from external electromagnetic fields, crosstalk and environmental effects. This combination of desirable characteristics are very beneficial to avionic ECM antenna remoting as well as many other applications. GEC-Marconi have developed high performance fiber components for use in a towed radar decoy. The resulting rugged and compact optical transmitter and receiver modules have been developed and proven to maintain the required performance over the full hostile range of environmental conditions encountered on a fast jet. Packaged fiber optic links have been produced which can achieve a compression dynamic range of greater than 87 dB in 1 MHz bandwidth over a 2 to 18 GHz.

Advanced microwave radiometer antenna system study

NASA Technical Reports Server (NTRS)

Kummer, W. H.; Villeneuve, A. T.; Seaton, A. F.

1976-01-01

The practicability of a multi-frequency antenna for spaceborne microwave radiometers was considered in detail. The program consisted of a comparative study of various antenna systems, both mechanically and electronically scanned, in relation to specified design goals and desired system performance. The study involved several distinct tasks: definition of candidate antennas that are lightweight and that, at the specified frequencies of 5, 10, 18, 22, and 36 GHz, can provide conical scanning, dual linear polarization, and simultaneous multiple frequency operation; examination of various feed systems and phase-shifting techniques; detailed analysis of several key performance parameters such as beam efficiency, sidelobe level, and antenna beam footprint size; and conception of an antenna/feed system that could meet the design goals. Candidate antennas examined include phased arrays, lenses, and optical reflector systems. Mechanical, electrical, and performance characteristics of the various systems were tabulated for ease of comparison.

Variable-frequency synchronous motor drives for electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chalmers, B.J.; Musaba, L.; Gosden, D.F.

1996-07-01

The performance capability envelope of a variable-frequency, permanent-magnet synchronous motor drive with field weakening is dependent upon the product of maximum current and direct-axis inductance. To obtain a performance characteristic suitable for a typical electric vehicle drive, in which short-term increase of current is applied, it is necessary to design an optimum value of direct-axis inductance. The paper presents an analysis of a hybrid motor design which uses a two-part rotor construction comprising a surface-magnet part and an axially laminated reluctance part. This arrangement combines the properties of all other types of synchronous motor and offers a greater choice ofmore » design variables. It is shown that the desired form of performance may be achieved when the high-inductance axis of the reluctance part is arranged to lead the magnet axis by 90{degree} (elec.).« less

Variable-frequency synchronous motor drives for electric vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chalmers, B.J.; Musaba, L.; Gosden, D.F.

1995-12-31

The performance capability envelope of a variable-frequency, permanent-magnet synchronous motor drive with field weakening is dependent upon the product of maximum current and direct-axis inductance. To obtain a performance characteristic suitable for a typical electric vehicle drive, in which short-term increase of current is applied, it is necessary to design an optimum value of direct-axis inductance. The paper presents an analysis of a hybrid motor design which uses a two-part rotor construction comprising a surface-magnet part and an axially-laminated reluctance part. This arrangement combines the properties of all other types of synchronous motor and offers a greater choice of designmore » variables. It is shown that the desired form of performance may be achieved when the high-inductance axis of the reluctance part is arranged to lead the magnet axis by 90{degree} (elec.).« less

Computational methods in the development of a knowledge-based system for the prediction of solid catalyst performance.

PubMed

Procelewska, Joanna; Galilea, Javier Llamas; Clerc, Frederic; Farrusseng, David; Schüth, Ferdi

2007-01-01

The objective of this work is the construction of a correlation between characteristics of heterogeneous catalysts, encoded in a descriptor vector, and their experimentally measured performances in the propene oxidation reaction. In this paper the key issue in the modeling process, namely the selection of adequate input variables, is explored. Several data-driven feature selection strategies were applied in order to obtain an estimate of the differences in variance and information content of various attributes, furthermore to compare their relative importance. Quantitative property activity relationship techniques using probabilistic neural networks have been used for the creation of various semi-empirical models. Finally, a robust classification model, assigning selected attributes of solid compounds as input to an appropriate performance class in the model reaction was obtained. It has been evident that the mathematical support for the primary attributes set proposed by chemists can be highly desirable.

Effects of Data Anonymization by Cell Suppression on Descriptive Statistics and Predictive Modeling Performance

PubMed Central

Ohno-Machado, Lucila; Vinterbo, Staal; Dreiseitl, Stephan

2002-01-01

Protecting individual data in disclosed databases is essential. Data anonymization strategies can produce table ambiguation by suppression of selected cells. Using table ambiguation, different degrees of anonymization can be achieved, depending on the number of individuals that a particular case must become indistinguishable from. This number defines the level of anonymization. Anonymization by cell suppression does not necessarily prevent inferences from being made from the disclosed data. Preventing inferences may be important to preserve confidentiality. We show that anonymized data sets can preserve descriptive characteristics of the data, but might also be used for making inferences on particular individuals, which is a feature that may not be desirable. The degradation of predictive performance is directly proportional to the degree of anonymity. As an example, we report the effect of anonymization on the predictive performance of a model constructed to estimate the probability of disease given clinical findings.

Effects of data anonymization by cell suppression on descriptive statistics and predictive modeling performance.

PubMed Central

Ohno-Machado, L.; Vinterbo, S. A.; Dreiseitl, S.

2001-01-01

Protecting individual data in disclosed databases is essential. Data anonymization strategies can produce table ambiguation by suppression of selected cells. Using table ambiguation, different degrees of anonymization can be achieved, depending on the number of individuals that a particular case must become indistinguishable from. This number defines the level of anonymization. Anonymization by cell suppression does not necessarily prevent inferences from being made from the disclosed data. Preventing inferences may be important to preserve confidentiality. We show that anonymized data sets can preserve descriptive characteristics of the data, but might also be used for making inferences on particular individuals, which is a feature that may not be desirable. The degradation of predictive performance is directly proportional to the degree of anonymity. As an example, we report the effect of anonymization on the predictive performance of a model constructed to estimate the probability of disease given clinical findings. PMID:11825239

Operating and environmental characteristics of Sigma Tau hydrogen masers used in the Very Long Baseline Array (VLBA)

NASA Technical Reports Server (NTRS)

Tucker, T. K.

1989-01-01

Presented here are the results obtained from performance evaluation of a pair of Sigma Tau Standards Corporation Model VLBA-112 active hydrogen maser frequency standards. These masers were manufactured for the National Radio Astronomy Observatory (NRAO) for use on the Very Long Baseline Array (VLBA) project and were furnished to the Jet Propulsion Laboratory (JPL) for the purpose of these tests. Tests on the two masers were performed in the JPL Frequency Standards Laboratory (FSL) and included the characterization of output frequency stability versus environmental factors such as temperature, humidity, magnetic field, and barometric pressure. The performance tests also included the determination of phase noise and Allan variance using both FSL and Sigma Tau masers as references. All tests were conducted under controlled laboratory conditions, with only the desired environmental and operational parameters varied to determine sensitivity to external environment.

Calculations of the Performance of a Compression-Ignition Engine-Compressor Turbine Combination I : Performance of a Highly Supercharged Compression-Ignition Engine

NASA Technical Reports Server (NTRS)

Sanders, J. C.; Mendelson, Alexander

1945-01-01

Small high-speed single-cylinder compression-ignition engines were tested to determine their performance characteristics under high supercharging. Calculations were made on the energy available in the exhaust gas of the compression-ignition engines. The maximum power at any given maximum cylinder pressure was obtained when the compression pressure was equal to the maximum cylinder pressure. Constant-pressure combustion was found possible at an engine speed of 2200 rpm. Exhaust pressures and temperatures were determined from an analysis of indicator cards. The analysis showed that, at rich mixtures with the exhaust back pressure equal to the inlet-air pressure, there is excess energy available for driving a turbine over that required for supercharging. The presence of this excess energy indicates that a highly supercharged compression-ignition engine might be desirable as a compressor and combustion chamber for a turbine.

Are the results of questionnaires measuring non-cognitive characteristics during the selection procedure for medical school application biased by social desirability?

PubMed Central

Obst, Katrin U.; Brüheim, Linda; Westermann, Jürgen; Katalinic, Alexander; Kötter, Thomas

2016-01-01

Introduction: A stronger consideration of non-cognitive characteristics in Medical School application procedures is desirable. Psychometric tests could be used as an economic supplement to face-to-face interviews which are frequently conducted during university internal procedures for Medical School applications (AdH, Auswahlverfahren der Hochschulen). This study investigates whether the results of psychometric questionnaires measuring non-cognitive characteristics such as personality traits, empathy, and resilience towards stress are vulnerable to distortions of social desirability when used in the context of selection procedures at Medical Schools. Methods: This study took place during the AdH of Lübeck University in August 2015. The following questionnaires have been included: NEO-FFI, SPF, and AVEM. In a 2x1 between-subject experiment we compared the answers from an alleged application condition and a control condition. In the alleged application condition we told applicants that these questionnaires were part of the application procedure. In the control condition applicants were informed about the study prior to completing the questionnaires. Results: All included questionnaires showed differences which can be regarded as social-desirability effects. These differences did not affect the entire scales but, rather, single subscales. Conclusion: These results challenge the informative value of these questionnaires when used for Medical School application procedures. Future studies may investigate the extent to which the differences influence the actual selection of applicants and what implications can be drawn from them for the use of psychometric questionnaires as part of study-place allocation procedures at Medical Schools. PMID:27990471

Are the results of questionnaires measuring non-cognitive characteristics during the selection procedure for medical school application biased by social desirability?

PubMed

Obst, Katrin U; Brüheim, Linda; Westermann, Jürgen; Katalinic, Alexander; Kötter, Thomas

2016-01-01

Introduction: A stronger consideration of non-cognitive characteristics in Medical School application procedures is desirable. Psychometric tests could be used as an economic supplement to face-to-face interviews which are frequently conducted during university internal procedures for Medical School applications (AdH, Auswahlverfahren der Hochschulen). This study investigates whether the results of psychometric questionnaires measuring non-cognitive characteristics such as personality traits, empathy, and resilience towards stress are vulnerable to distortions of social desirability when used in the context of selection procedures at Medical Schools. Methods: This study took place during the AdH of Lübeck University in August 2015. The following questionnaires have been included: NEO-FFI, SPF, and AVEM. In a 2x1 between-subject experiment we compared the answers from an alleged application condition and a control condition. In the alleged application condition we told applicants that these questionnaires were part of the application procedure. In the control condition applicants were informed about the study prior to completing the questionnaires. Results: All included questionnaires showed differences which can be regarded as social-desirability effects. These differences did not affect the entire scales but, rather, single subscales. Conclusion: These results challenge the informative value of these questionnaires when used for Medical School application procedures. Future studies may investigate the extent to which the differences influence the actual selection of applicants and what implications can be drawn from them for the use of psychometric questionnaires as part of study-place allocation procedures at Medical Schools.

A Holistic Model for Wellness and Prevention over the Life Span.

ERIC Educational Resources Information Center

Witmer, J. Melvin; Sweeney, Thomas J.

1992-01-01

Presents integrated paradigm for wellness and prevention over the life span for purpose of theory building, research, clinical application, education, advocacy, and consciousness raising. Model described includes 11 characteristics desirable for optimal health and functioning. Notes characteristics are expressed through five life tasks of…

Effective Instructional Characteristics of Teachers of Junior High School Gifted Students.

ERIC Educational Resources Information Center

Wendel, Robert; Heiser, Sandra

1989-01-01

An ethnographic study analyzed videotapes using simulated recall procedure and comparative analysis of a student opinionnaire to determine effective characteristics of teachers of gifted junior high schools students. Desirable traits noted were humor, enthusiasm, creativity, care and respect for students, and high expectations. (MSE)

77 FR 73454 - Revision of Information Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-10

... ensure that requested data can be provided in the desired format, reporting burden (time and financial... with standard national performance measure requirements; revise the Grant Application Narrative... express the desired outcomes; Facilitate stronger alignment between narrative sections and the performance...

Simulation and optimization of deep violet InGaN double quantum well laser

NASA Astrophysics Data System (ADS)

Alahyarizadeh, Gh.; Ghazai, A. J.; Rahmani, R.; Mahmodi, H.; Hassan, Z.

2012-03-01

The performance characteristics of a deep violet InGaN double quantum well laser diode (LD) such as threshold current ( Ith), external differential quantum efficiency (DQE) and output power have been investigated using the Integrated System Engineering Technical Computer Aided Design (ISE-TCAD) software. As well as its operating parameters such as internal quantum efficiency ( ηi), internal loss ( αi) and transparency threshold current density ( J0) have been studied. Since, we are interested to investigate the mentioned characteristics and parameters independent of well and barrier thickness, therefore to reach a desired output wavelength, the indium mole fraction of wells and barriers has been varied consequently. The indium mole fractions of well and barrier layers have been considered 0.08 and 0.0, respectively. Some important parameters such as Al mole fraction of the electronic blocking layer (EBL) and cavity length which affect performance characteristics were also investigated. The optimum values of the Al mole fraction and cavity length in this study are 0.15 and 400 μm, respectively. The lowest threshold current, the highest DQE and output power which obtained at the emission wavelength of 391.5 nm are 43.199 mA, 44.99% and 10.334 mW, respectively.

Desirability function combining metabolic stability and functionality of peptides.

PubMed

Van Dorpe, Sylvia; Adriaens, Antita; Vermeire, Simon; Polis, Ingeborgh; Peremans, Kathelijne; Spiegeleer, Bart De

2011-05-01

The evaluation of peptides as potential therapeutic or diagnostic agents requires the consideration of several criteria that are targeted around two axes: functionality and metabolic stability. Most often, a compromise has to be made between these mutually opposing characteristics. In this study, Derringer's desirability function, a multi-criteria decision-making method, was applied to determine the best peptide for opioid studies in a single figure-of-merit. The penetration of the blood-brain barrier (BBB) determines the biological functionality of neuropeptides in the brain target tissue, and consists of an influx and an efflux component. The metabolic stability in the two concerned tissues, i.e. plasma and brain, are taken into consideration as well. The overall selection of the peptide drug candidate having the highest BBB-drugability is difficult due to these conflicting responses as well as the different scalings of the four biological parameters under consideration. The highest desirability, representing the best BBB-drugability, was observed for dermorphin. This peptide is thus the most promising drug candidate from the set of eight opioid peptides that were investigated. The least desirable candidate, with the worst BBB influx and/or metabolic stability, was found to be CTAP. Validation of the desirability function by in vivo medical imaging showed that dermorphin and DAMGO penetrate the BBB, whereas EM-1 and TAPP did not. These results are thus consistent with those obtained with the desirability evaluation. To conclude, the multi-criteria decision method was proven to be useful in biomedical research, where a selection of the best candidate based on opposing characteristics is often required. Copyright © 2011 European Peptide Society and John Wiley & Sons, Ltd.

Preschoolers' Understanding of Others' Desires: Fulfilling Mine Enhances My Understanding of Yours

ERIC Educational Resources Information Center

Atance, Cristina M.; Belanger, Michele; Meltzoff, Andrew N.

2010-01-01

We developed a gift-giving task requiring children to identify their mother's desire, when her desire differed from theirs. We found a developmental change: 3- and 4-year-olds performed more poorly than 5-year-olds (Experiment 1). A modified version of this task (Experiment 2) revealed that 3-, 4-, and 5-year-olds whose desires had been fulfilled…

Characterization of solidifiers used for oil spill remediation.

PubMed

Sundaravadivelu, Devi; Suidan, Makram T; Venosa, Albert D; Rosales, Pablo I

2016-02-01

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial products were primarily comprised of organic polymers and a few trace elements. A natural sorbent, which was composed entirely of plant based matter, was also evaluated, and it had the highest oil removal capacity, but it did not produce a solid mat-like final product. Generally, solidifiers with a carbonate group, pore size greater than 5 μm, and bulk densities lower than 0.3 g cm(-3) were found to have better efficiency and produced a cohesive rubbery final product that facilitated removal compared to sorbents. The importance of bulk density and pore size in the performance of the solidifier suggest that the primary mechanism of action was likely physical sorption. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance analysis and material dependence of micro holographic optical elements as couplers for fiber optic communication

NASA Astrophysics Data System (ADS)

Ambadiyil, Sajan; Prasannan, G.; Sathyan, Jithesh; Ajith Kumar, P. T.

2005-01-01

Holographic Optical Elements (HOEs) are gaining much importance and finding newer and better applications in areas of optical fiber communication and optical information processing systems. In contrast to conventional HOEs, optical communication and information systems require smaller and efficient elements of desired characteristics and transfer functions. Such Micro Holographic Optical Elements (MHOEs) can either be an HOE, recorded with two narrow beams of laser light or a segment cut from a larger HOE (SHOEs), and recorded in the conventional manner. In this study, micro holographic couplers, having specific focusing and diffraction characteristics were recorded in different holographic recording media such as silver halide and dichromated gelatin. Wavelength response of the elements was tested at 633 nm and 442 nm. Variation in diffraction efficiency/coupling factor, and insertion loss of the elements were studied. The paper reports in detail about the above results and related design considerations.

Method and system for reducing device performance degradation of organic devices

DOEpatents

Teague, Lucile C.

2014-09-02

Methods and systems for reducing the deleterious effects of gate bias stress on the drain current of an organic device, such as an organic thin film transistor, are provided. In a particular aspect, the organic layer of an organic device is illuminated with light having characteristics selected to reduce the gate bias voltage effects on the drain current of the organic device. For instance, the wavelength and intensity of the light are selected to provide a desired recovery of drain current of the organic device. If the characteristics of the light are appropriately matched to the organic device, recovery of the deleterious effects caused by gate bias voltage stress effects on the drain current of the organic device can be achieved. In a particular aspect, the organic device is selectively illuminated with light to operate the organic device in multiple modes of operation.

The characteristics and experiences of mature nursing students.

PubMed

Montgomery, Laura E A; Tansey, Etain A; Roe, Sean M

To explore the characteristics of mature nursing students, including how they perceive themselves, and to identify the problems they experience, which may influence whether they continue with their course. A sample of 239 students completed an anonymous questionnaire at the end of their first year of study for a diploma in nursing science. A question concerning age was included to enable identification of mature students, of which there were 90. Mature students as a group were desirable students, tending to perform better academically than their younger counterparts and bringing a wealth of caring experience to the course. However, mature students experienced additional pressures, for example financial concerns. When considering the potential benefits of educating mature students, the government and universities should be encouraging their recruitment and retention. An increase in the bursary and free or heavily subsidised childcare would help to alleviate financial concerns.

Vicarious intergroup contact and the role of authorities in prejudice reduction.

PubMed

Gómez, Angel; Huici, Carmen

2008-05-01

The present study focuses on the effect of vicarious intergroup contact and the support of an authority figure on the improvement of outgroup and meta-stereotype evaluations. Meta-stereotype refers to the shared beliefs of ingroup members about how they consider outgroup members to perceive their group. Three preliminary studies were carried out to determine desirable and undesirable characteristics for a good basketball performance, the task that best demonstrates the application of these characteristics, and the two groups (basketball teams) that should be involved in the vicarious intergroup contact. Fans of one of the basketball teams participated in the current study. Vicarious intergroup contact improved outgroup and meta-stereotype evaluations as compared with a no contact condition. In addition, the positive effects of vicarious intergroup contact significantly increased when it was supported by an authority figure. More importantly, our study also shows that the improvement of outgroup evaluation was partially mediated by changes on meta-stereotypes.

Exodus: Prime Mover

NASA Technical Reports Server (NTRS)

Bauer, Nikkol; Conwell, Pete; Johnson, Matt; Shields, Wendy; Thornton, Tim; Tokarz, Rob; Mcmanus, Rich

1992-01-01

The Exodus Prime Mover is an overnight package delivery aircraft designed to serve the Northern Hemisphere of Aeroworld. The preliminary design goals originated from the desire to produce a large profit. The two main driving forces throughout the design process were first to reduce the construction man-hours by simplifying the aircraft design, thereby decreasing the total production cost of the aircraft. The second influential factor affecting the design was minimizing the fuel cost during cruise. The lowest fuel consumption occurs at a cruise velocity of 30 ft/s. Overall, it was necessary to balance the economic benefits with the performance characteristics in order to create a profitable product that meets all specified requirements and objectives.

Aerodynamic and Hydrodynamic Tests of a Family of Models of Flying Hulls Derived from a Streamline Body -- NACA Model 84 Series

NASA Technical Reports Server (NTRS)

Parkinson, John B; Olson, Roland E; Draley, Eugene C; Luoma, Arvo A

1943-01-01

A series of related forms of flying-boat hulls representing various degrees of compromise between aerodynamic and hydrodynamic requirements was tested in Langley Tank No. 1 and in the Langley 8-foot high-speed tunnel. The purpose of the investigation was to provide information regarding the penalties in water performance resulting from further aerodynamic refinement and, as a corollary, to provide information regarding the penalties in range or payload resulting from the retention of certain desirable hydrodynamic characteristics. The information should form a basis for over-all improvements in hull form.

Low-speed single-element airfoil synthesis

NASA Technical Reports Server (NTRS)

Mcmasters, J. H.; Henderson, M. L.

1979-01-01

The use of recently developed airfoil analysis/design computational tools to clarify, enrich and extend the existing experimental data base on low-speed, single element airfoils is demonstrated. A discussion of the problem of tailoring an airfoil for a specific application at its appropriate Reynolds number is presented. This problem is approached by use of inverse (or synthesis) techniques, wherein a desirable set of boundary layer characteristics, performance objectives, and constraints are specified, which then leads to derivation of a corresponding viscous flow pressure distribution. Examples are presented which demonstrate the synthesis approach, following presentation of some historical information and background data which motivate the basic synthesis process.

Development of an analytical method to predict helicopter main rotor performance in icing conditions

NASA Technical Reports Server (NTRS)

Britton, Randall K.

1992-01-01

Historically, certification of a helicopter for flight into known icing conditions was a problem. This is because of the current emphasis on flight testing for verification of system performance. Flight testing in icing conditions is difficult because, in addition to being dangerous and expensive, many times conditions which are sought after cannot be readily found in nature. The problem is compounded for helicopters because of their small range in comparison to many fixed wing aircraft. Thus, helicopters are forced to wait for conditions to occur in a certain region rather than seeking them out. These and other drawbacks to flight testing prompted extreme interest in developing validated alternatives to flight testing. One such alternative is theoretical prediction. It is desirable to have the ability to predict how a helicopter will perform when subjected to icing conditions. Herein, calculations are restricted to the main rotor, and are illustrated. The computational tool used to obtain performance is the lifting line analysis of B65. B65 incorporates experimental data into data banks in order to determine the section lift, drag, and moment characteristics of various airfoils at different Mach numbers and angles of attack. The local flow angle is calculated at user specified radial locations. This flow angle, along with the local Mach number is then cross referenced with the airfoil tables to obtain the local section characteristics. The local characteristics are then integrated together to obtain the entire rotor attributes. Once the clean performance is known, characterization of the type and shape of ice which accretes on the rotor blades is obtained using the analysis of LEWICE. The Interactive Boundary Layer (IBL) method then calculates the 2-D characteristics of the iced airfoil for input into the airfoil data bank of B65. Calculations are restricted to natural ice shedding and it is assumed that no de-icing takes place. Once the new lift, drag, and moment characteristics are known for the entire blade radius, this information is fed into B65, where the iced performance is then calculated.

Smoking characteristics among lesbian, gay, and bisexual adults☆

PubMed Central

Fallin, Amanda; Goodin, Amie; Lee, Youn Ok; Bennett, Keisa

2015-01-01

Objective Cigarette smoking is the leading preventable cause of death and disease in the United States. Sexual minorities (lesbians, gay men, and bisexuals), smoke at higher rates than the general population. However, little else is known about sexual minority smokers. Furthermore, the sexual minority population is diverse and little research exists to determine whether subgroups, such as lesbians, gay men, and female and male bisexuals, differ on smoker characteristics. We examine differences in smoking characteristics (advertising receptivity, age of first cigarette, non-daily smoking, cigarettes per day, nicotine dependence, desire to quit and past quit attempts) among lesbians, gay men, and female and male bisexual adults in the United States. Methods Secondary analysis of the CDC's 2009–2010 National Adult Tobacco Survey (N = 118,590). Results Controlling for age, race, socioeconomic status and geographic region, identifying as a female bisexual was associated with fewer past quit attempts, lower age at first cigarette, and higher nicotine dependence when compared to heterosexual women. There were no differences in desire to quit between male or female sexual minorities and their heterosexual counterparts. Conclusion Sexual minority individuals smoke at higher rates than heterosexuals and yet similarly desire to quit. Tailored efforts may be needed to address smoking among bisexual women. PMID:25485860

C-Tactile Mediated Erotic Touch Perception Relates to Sexual Desire and Performance in a Gender-Specific Way.

PubMed

Bendas, Johanna; Georgiadis, Janniko R; Ritschel, Gerhard; Olausson, Håkan; Weidner, Kerstin; Croy, Ilona

2017-05-01

Unmyelinated low-threshold mechanoreceptors-the so-called C-tactile (CT) afferents-play a crucial role in the perception and conduction of caressing and pleasant touch sensations and significantly contribute to the concept of erotic touch perception. To investigate the relations between sexual desire and sexual performance and the perception of touch mediated by CT afferents. Seventy healthy participants (28 men, 42 women; mean age ± SD = 24.84 ± 4.08 years, range = 18-36 years) underwent standardized and highly controlled stroking stimulation that varied in the amount of CT fiber stimulation by changing stroking velocity (CT optimal = 1, 3 and 10 cm/s; CT suboptimal = 0.1, 0.3, and 30 cm/s). Participants rated the perceived pleasantness, eroticism, and intensity of the applied tactile stimulation on a visual analog scale, completed the Sexual Desire Inventory, and answered questions about sexual performance. Ratings of perceived eroticism of touch were related to self-report levels of sexual desire and sexual performance. Pleasantness and eroticism ratings showed similar dependence on stroking velocity that aligned with the activity of CT afferents. Erotic touch perception was related to sexual desire and sexual performance in a gender-specific way. In women, differences in eroticism ratings between CT optimal and suboptimal velocities correlated positively with desire for sexual interaction. In contrast, in men, this difference correlated to a decreased frequency and longer duration of partnered sexual activities. The present results lay the foundation for future research assessing these relations in patients with specific impairments of sexual functioning (eg, hypoactive sexual desire disorder). The strength of the study is the combination of standardized neurophysiologic methods and behavioral data. A clear limitation of the study design is the exclusion of exact data on the female menstrual cycle and the recruitment of an inhomogeneous sample concerning sexual orientation. The present results provide further evidence that unmyelinated CT afferents play a role in the complex mechanism of erotic touch perception. The ability to differentiate between CT optimal and suboptimal stimuli relates to sexual desire and performance in a gender-specific way. Bendas J, Georgiadis JR, Ritschel G. C-Tactile Mediated Erotic Touch Perception Relates to Sexual Desire and Performance in a Gender-Specific Way. J Sex Med 2017;14:645-653. Copyright © 2017 International Society for Sexual Medicine. Published by Elsevier Inc. All rights reserved.

What do UK doctors in training value in a post? A discrete choice experiment.

PubMed

Cleland, Jennifer; Johnston, Peter; Watson, Verity; Krucien, Nicolas; Skåtun, Diane

2016-02-01

Many individual and job-related factors are known to influence medical careers decision making. Medical trainees' (residents) views of which characteristics of a training post are important to them have been extensively studied but how they trade-off these characteristics is under-researched. Such information is crucial for the development of effective policies to enhance recruitment and retention. Our aim was to investigate the strength of UK foundation doctors' and trainees' preferences for training post characteristics in terms of monetary value. We used an online questionnaire study incorporating a discrete choice experiment (DCE), distributed to foundation programme doctors and doctors in training across all specialty groups within three UK regions, in August-October 2013. The main outcome measures were monetary values for training-post characteristics, based on willingness to forgo and willingness to accept extra income for a change in each job characteristic, calculated from regression coefficients. The questionnaire was answered by 1323 trainees. Good working conditions were the most influential characteristics of a training position. Trainee doctors would need to be compensated by an additional 49.8% above the average earnings within their specialty to move from a post with good working conditions to one with poor working conditions. A training post with limited rather than good opportunities for one's spouse or partner would require compensation of 38.4% above the average earnings within their specialty. Trainees would require compensation of 30.8% above the average earnings within their specialty to move from a desirable to a less desirable locality. These preferences varied only to a limited extent according to individual characteristics. Trainees place most value on good working conditions, good opportunities for their partners and desirable geographical location when making career-related decisions. This intelligence can be used to develop alternative models of workforce planning or to develop information about job opportunities that address trainees' values. © 2016 John Wiley & Sons Ltd.

Patients' views of consent in clinical trials for acute myocardial infarction: impact of trial design.

PubMed

Dickert, Neal W; Hendershot, Kristopher A; Speight, Candace D; Fehr, Alexandra E

2017-08-01

Seeking prospective informed consent is difficult in clinical trials for emergent conditions such as acute myocardial infarction (AMI). Prior data suggest that enrolment decisions of patients are often poorly informed in AMI trials but that patients prefer to be asked permission before enrolment. It is unknown whether this is true across trial designs or in comparative effectiveness research (CER) with approved treatments. Structured interviews were conducted with 30 patients with AMI. Participants considered three scenarios: (1) a CER trial of approved antiplatelet drugs; (2) a placebo-controlled trial of a novel drug to reduce myocardial injury and (3) a CER trial of an intra-aortic balloon pump versus medication. Participants were asked their desired involvement in enrolment decisions and willingness to participate. Descriptive analysis was performed of Likert scale data, and qualitative descriptive analysis was performed of textual data. Across scenarios, most participants (73%-80%) preferred to be asked permission prior to trial enrolment. Reasons for involvement included wanting to be the decision maker and a desire for transparency. Willingness to enrol was affected by trial type. Fewer participants stated they would likely enrol in a CER procedural trial than in a CER trial of approved medications (p=0.012). These findings suggest that patients prefer prospective involvement in enrolment decisions to enrolment without consent across trial types. However, their desire to participate was affected by trial type. There is a need to develop and evaluate context-sensitive approaches to consent in AMI trials that account for both the acuity of the situation and trial characteristics. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

[Creating an integrated nursing curriculum].

PubMed

Romano, R A; Papa, L M; Lopes, G T

1997-01-01

During the last two decades, Brazilian society has gone through great changes into political, ideological and economical fields. These changes left their strings into society, specially in population health. The nurse formation based on the Law n(o) 5540/68 and on the Statement n(o) 163/72, no more meets population demands. Since 1992, the Nursing Faculty of UERJ-FEUerj intensifies the reflection movement upon teaching-learning process searching for transforming its own reality. The making of this project presents two complementary and important reasons: FEUerj docents and discents' desire in elaborating a curriculum which searches for nurses' formation that articulates teaching-work-community, theory and practice, based on a Critical Theory of Education, on the line of PROBLEMATIZATION, and the accomplishment of Statement n(o) 314/94 from the CFE and from the Letter of Order MEC n(o) 1171/15/dez/94. From debating, the professional profile has been defined from the social environment where the profession is performed and the alumnate's characteristics; area determination or group of attributions, according to professional praxis adequation, concept hierachization, processes, etc., which in the process of 'classification and syntheses' of knowledge results into a netlike chained and related tree. In the first phase of the curriculum study, it has diagnosed as principal condition, the actual curriculum 'DECONTEXTUALIZATION' and the 'US' to be faced to lead it to an end the Curriculum Reformulation Proposal. The Process of Pedagogical Abilitation for professors, workshops, researches on the desirable and present profile, seminars, performance, abilities and principles systematization, identification of areas which compose the integrated curriculum, subjects localization into areas and articulation between professional subjects and other activities, has been implemented. Based on this work on the problematized pedagogy first step, an instrument 'Research on the Professional Profile for the Nursing Graduation Course', was built, identifying the performances and principles which sustain them on each subject making the present profile clear and desirable to docents and discents.

Novel hybrid isotope separation scheme and apparatus

DOEpatents

Maya, Jakob

1991-01-01

A method of yielding selectively a desired enrichment in a specific isotope including the steps of inputting into a spinning chamber a gas from which the specific isotope is to be isolated, radiating the gas with frequencies characteristic of the absorption of a particular isotope of the atomic or molecular gas, thereby inducing a photoionization reaction of the desired isotope, and collecting the specific isotope ion by suitable ion collection means.

Characteristics of Predoctoral Endodontic Education in the United States and Canada.

ERIC Educational Resources Information Center

Mendel, Robert W.; Scheetz, James P.

1981-01-01

A survey to assess the current state of predoctoral endodontic education programs in U.S. and Canadian dental schools is discussed. The investigation focused on faculty characteristics, the learning climate for endodontics, and problems of administration. Current learning conditions were compared with the desirability of these conditions.…

Desired Job Characteristics for Males and Females

ERIC Educational Resources Information Center

Pyke, Sandra W.; Weisenberg, Faye

1976-01-01

A sample of 42 professional and 46 non-professional men and women reported order of preference for 10 job characteristics (five motivators and five hygienes). Both sexes regarded motivators as personally more important than hygienes but non-professional respondents were significantly more concerned about hygienes than the professional group.…

AN ASSESSMENT OF AUTOMATIC SEWER FLOW SAMPLERS (EPA/600/2-75/065)

EPA Science Inventory

A brief review of the characteristics of storm and combined sewer flows is given followed by a general discussion of the purposes for and requirements of a sampling program. The desirable characteristics of automatic sampling equipment are set forth and problem areas are outlined...

Design and experiment study of a semi-active energy-regenerative suspension system

NASA Astrophysics Data System (ADS)

Shi, Dehua; Chen, Long; Wang, Ruochen; Jiang, Haobin; Shen, Yujie

2015-01-01

A new kind of semi-active energy-regenerative suspension system is proposed to recover suspension vibration energy, as well as to reduce the suspension cost and demands for the motor-rated capacity. The system consists of an energy-regenerative damper and a DC-DC converter-based energy-regenerative circuit. The energy-regenerative damper is composed of an electromagnetic linear motor and an adjustable shock absorber with three regulating levels. The linear motor just works as the generator to harvest the suspension vibration energy. The circuit can be used to improve the system’s energy-regenerative performance and to continuously regulate the motor’s electromagnetic damping force. Therefore, although the motor works as a generator and damps the isolation without an external power source, the motor damping force is controllable. The damping characteristics of the system are studied based on a two degrees of freedom vehicle vibration model. By further analyzing the circuit operation characteristics under different working modes, the double-loop controller is designed to track the desired damping force. The external-loop is a fuzzy controller that offers the desired equivalent damping. The inner-loop controller, on one hand, is used to generate the pulse number and the frequency to control the angle and the rotational speed of the step motor; on the other hand, the inner-loop is used to offer the duty cycle of the energy-regenerative circuit. Simulations and experiments are conducted to validate such a new suspension system. The results show that the semi-active energy-regenerative suspension can improve vehicle ride comfort with the controllable damping characteristics of the linear motor. Meanwhile, it also ensures energy regeneration.

Are You a Dream Come True or a Nightmare? Desired Characteristics in the Face to Face and Online Instructor

ERIC Educational Resources Information Center

Patton, Aldis; Lesage, Teresa

2010-01-01

All instructors would all like to be a "Dream Come True" but unfortunately many come across to their students as a "nightmare". The purpose of this study was to determine the characteristics in effective and successful online and/or face-to-face instructors. Characteristics as perceived by pre-service teachers in each setting…

Isolation and Characterization of Brewer's Yeast Variants with Improved Fermentation Performance under High-Gravity Conditions▿

PubMed Central

Blieck, Lies; Toye, Geert; Dumortier, Françoise; Verstrepen, Kevin J.; Delvaux, Freddy R.; Thevelein, Johan M.; Van Dijck, Patrick

2007-01-01

To save energy, space, and time, today's breweries make use of high-gravity brewing in which concentrated medium (wort) is fermented, resulting in a product with higher ethanol content. After fermentation, the product is diluted to obtain beer with the desired alcohol content. While economically desirable, the use of wort with an even higher sugar concentration is limited by the inability of brewer's yeast (Saccharomyces pastorianus) to efficiently ferment such concentrated medium. Here, we describe a successful strategy to obtain yeast variants with significantly improved fermentation capacity under high-gravity conditions. We isolated better-performing variants of the industrial lager strain CMBS33 by subjecting a pool of UV-induced variants to consecutive rounds of fermentation in very-high-gravity wort (>22° Plato). Two variants (GT336 and GT344) showing faster fermentation rates and/or more-complete attenuation as well as improved viability under high ethanol conditions were identified. The variants displayed the same advantages in a pilot-scale stirred fermenter under high-gravity conditions at 11°C. Microarray analysis identified several genes whose altered expression may be responsible for the superior performance of the variants. The role of some of these candidate genes was confirmed by genetic transformation. Our study shows that proper selection conditions allow the isolation of variants of commercial brewer's yeast with superior fermentation characteristics. Moreover, it is the first study to identify genes that affect fermentation performance under high-gravity conditions. The results are of interest to the beer and bioethanol industries, where the use of more-concentrated medium is economically advantageous. PMID:17158628

Characteristics of Urban Sidewalks/Streets and Objectively Measured Physical Activity

PubMed Central

Heinrich, Katie M.; Poston, Walker S.C.; Hyder, Melissa; Pyle, Sara

2007-01-01

Several studies have found significant relationships between environmental characteristics (e.g., number of destinations, aesthetics) and physical activity. While a few of these studies verified that the physical activities assessed were performed in the environments examined, none have done this in an urban, neighborhood setting. This information will help efforts to inform policy decisions regarding the design of more “physically active” communities. Fourteen environmental characteristics of 60, 305-m-long segments, located in an urban, residential setting, were directly measured using standardized procedures. The number of individuals walking, jogging, and biking in the segments was assessed using an observation technique. The segments were heterogeneous with regards to several of the environmental characteristics. A total of 473 individuals were seen walking, bicycling, or jogging in the segments during 3,600 min of observation (60 min/segment). Of the 473 seen, 315 were walking, 116 bicycling, and 42 jogging. A greater number of individuals were seen walking in segments with more traffic, sidewalk defects, graffiti, and litter and less desirable property aesthetics. Only one environmental characteristic was associated with bicycling and none were significantly related with jogging. This study provides further evidence that environmental characteristics and walking are related. It also adds new information regarding the importance of scale (e.g., micro, macro) and how some environmental characteristics of urban, residential sidewalks and streets relate to physical activity. PMID:18161026

When performance-approach goals predict academic achievement and when they do not: a social value approach.

PubMed

Dompnier, Benoît; Darnon, Céline; Butera, Fabrizio

2013-09-01

Research on achievement goal promotion at University has shown that performance-approach goals are perceived as a means to succeed at University (high social utility) but are not appreciated (low social desirability). We argue that such a paradox could explain why research has detected that performance-approach goals consistently predict academic grades. First-year psychology students answered a performance-approach goal scale with standard, social desirability and social utility instructions. Participants' grades were recorded at the end of the semester. Results showed that the relationship between performance-approach goals and grades was inhibited by the increase of these goals' social desirability and facilitated by the increase of their social utility, revealing that the predictive validity of performance-approach goals depends on social value. © 2013 The British Psychological Society.

A computerized education module improves patient knowledge and attitudes about appropriate antibiotic use for acute respiratory tract infections.

PubMed

Price, Erika Leemann; Mackenzie, Thomas D; Metlay, Joshua P; Camargo, Carlos A; Gonzales, Ralph

2011-12-01

Over-use of antibiotics for acute respiratory infections (ARIs) increases antimicrobial resistance, treatment costs, and side effects. Patient desire for antibiotics contributes to over-use. To explore whether a point-of-care interactive computerized education module increases patient knowledge and decreases desire for antibiotics. Bilingual (English/Spanish) interactive kiosks were available in 8 emergency departments as part of a multidimensional intervention to reduce antibiotic prescribing for ARIs. The symptom-tailored module included assessment of symptoms, knowledge about ARIs (3 items), and desire for antibiotics on a 10-point visual analog scale. Multivariable analysis assessed predictors of change in desire for antibiotics. Of 686 adults with ARI symptoms, 63% initially thought antibiotics might help. The proportion of patients with low (1-3 on the scale) desire for antibiotics increased from 22% pre-module to 49% post-module (p<.001). Self-report of "learning something new" was associated with decreased desire for antibiotics, after adjusting for baseline characteristics (p=.001). An interactive educational kiosk improved knowledge about antibiotics and ARIs. Learning correlated with changes in personal desire for antibiotics. By reducing desire for antibiotics, point-of-care interactive educational computer technology may help decrease inappropriate use for antibiotics for ARIs. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Reactor/Brayton power systems for nuclear electric spacecraft

NASA Technical Reports Server (NTRS)

Layton, J. P.

1980-01-01

Studies are currently underway to assess the technological feasibility of a nuclear-reactor-powered spacecraft propelled by electric thrusters. This vehicle would be capable of performing detailed exploration of the outer planets of the solar system during the remainder of this century. The purpose of this study was to provide comparative information on a closed cycle gas turbine power conversion system. The results have shown that the performance is very competitive and that a 400 kWe space power system is dimensionally compatible with a single Space Shuttle launch. Performance parameters of system mass and radiator area were determined for systems from 100 to 1000 kWe. A 400 kWe reference system received primary attention. The components of this system were defined and a conceptual layout was developed with encouraging results. The preliminary mass determination for the complete power system was very close to the desired goal of 20 kg/kWe. Use of more advanced technology (higher turbine inlet temperature) will substantially improve system performance characteristics.

Son Preference in Pakistan; A Myth or Reality.

PubMed

Atif, Khaula; Ullah, Muhammad Zia; Afsheen, Afeera; Naqvi, Syed Abid Hassan; Raja, Zulqarnain Ashraf; Niazi, Saleem Asif

2016-01-01

To analyze desire for sons/daughters among ladies of Peshawar, Pakistan, with a view to rule out son preference and to study impact of various demographic characteristics on the subject. Cross-sectional descriptive study conducted at Combined Military Hospital, Peshawar, from August 2015 - January 2016; sampling technique was random/probability/non-purposive. Self-designed questionnaire was utilized; carrying questions pertinent to desire for sons/daughters during marital life, and demographic details. Data analyzed via descriptive analysis (SPSS-21), expressed as frequencies/percentages and mean ± standard deviation(minimum/maximum). Sons and daughters desired (dependent variables) were cross-tabulated with independent variables. Response rate was 63.25% (n-506). Data revealed following: Sons desired 3.05±2.061(1/12); Daughters desired 1.15±0.767(0/4); 6.1%(n-31) and 0.6%(n-3) desired infinite number of sons and daughters respectively, 18.2%(n-92) did not desire to have even one daughter, while 2.2%(n-11) considered it immaterial to have daughters or sons. There was a significant relation between sons desired and client's education (p<0.001), husband's education (p<0.001) and socioeconomic class (p<0.001). There was no significant impact of religion (p-0.142) on desire for sons. Impact of independent variables on daughters desired was similar but less pronounced. There was candid son preference among the respondents. Gender discrimination can be attenuated by adequately addressing son preference at all tiers.

Study of thermo-fluidic behavior of micro-droplet in inkjet-based micro manufacturing processes

NASA Astrophysics Data System (ADS)

Das, Raju; Mahapatra, Abhijit; Ball, Amit Kumar; Roy, Shibendu Shekhar; Murmu, Naresh Chandra

2017-06-01

Inkjet printing technology, a maskless, non-contact patterning operation, which has been a revelation in the field of micro and nano manufacturing for its use in the selective deposition of desired materials. It is becoming an exciting alternative technology such as lithography to print functional material on to a substrate. Selective deposition of functional materials on desired substrates is a basic requirement in many of the printing based micro and nano manufacturing operations like the fabrication of microelectronic devices, solar cell, Light-emitting Diode (LED) research fields like pharmaceutical industries for drug discovery purposes and in biotechnology to make DNA microarrays. In this paper, an attempt has been made to design and develop an indigenous Electrohydrodynamic Inkjet printing system for micro fabrication and to study the interrelationships between various thermos-fluidic parameters of the ink material in the printing process. The effect of printing process parameters on printing performance characteristics has also been studied. And the applicability of the process has also been experimentally demonstrated. The experimentally found results were quite satisfactory and accordance to its applicability.

Optimal Control Allocation with Load Sensor Feedback for Active Load Suppression, Flight-Test Performance

NASA Technical Reports Server (NTRS)

Miller, Christopher J.; Goodrick, Dan

2017-01-01

The problem of control command and maneuver induced structural loads is an important aspect of any control system design. The aircraft structure and the control architecture must be designed to achieve desired piloted control responses while limiting the imparted structural loads. The classical approach is to utilize high structural margins, restrict control surface commands to a limited set of analyzed combinations, and train pilots to follow procedural maneuvering limitations. With recent advances in structural sensing and the continued desire to improve safety and vehicle fuel efficiency, it is both possible and desirable to develop control architectures that enable lighter vehicle weights while maintaining and improving protection against structural damage. An optimal control technique has been explored and shown to achieve desirable vehicle control performance while limiting sensed structural loads to specified values. This technique has been implemented and flown on the National Aeronautics and Space Administration Full-scale Advanced Systems Testbed aircraft. The flight tests illustrate that the approach achieves the desired performance and show promising potential benefits. The flights also uncovered some important issues that will need to be addressed for production application.

Male Sexual Quality Of Life Is Maintained Satisfactorily Throughout Life In The Amazon Rainforest.

PubMed

Teixeira, Thiago; Nazima, Maira; Hallak, Jorge

2018-06-01

The Amazon Rainforest is a cradle of biodiversity, where different ethnic groups have specific sexual habits. To define the average sexual quality of life of Amazonian men 18 to 69 years old, evaluate the influence of aging on their sexual function, and calculate the prevalence of premature ejaculation, delayed ejaculation, and hypoactive sexual desire disorder. A cross-sectional quantitative probability sample study was performed with a demographically representative population (N = 385), with data collected privately at participants' houses, including men who had been sexually active for a minimum of 6 months. The Male Sexual Quotient (MSQ) was used to measure sexual satisfaction and function. Statistical analysis was performed with SPSS 21.0 using the Kruskal-Wallis test (P < .05), and a multiple linear regression analysis was performed to investigate which factors could predict participants' quality of sexual life. MSQ scores. The response rate was 81.69%. The mean age was 36.00 ± 12.95 years, and most men had mixed ethnicity (63.11%), were self-employed (42.07%), had a monthly earned income of US$0 to US$460 (46.75%), and were single (36.10%). The mean MSQ score was 80.39 ± 12.14 (highly satisfied). None of the demographic characteristics showed a statistically significant influence on sexual satisfaction. The difference in quality of sexual life was statistically significant compared with age (P < .01). The domains of desire (P < .01), partner satisfaction (P = .04), and erection quality (P < .01, P = .03, P = .02) were statistically significant. Prevalences of sexual dysfunctions were 36.54% for premature ejaculation, 6.5% for delayed ejaculation, and 11.69% for hypoactive sexual desire disorder. Independent of age, these men have an excellent quality of sexual life. Sexual domains such as desire, partner satisfaction, and erection quality are related to the correlation between sexual quality of life and aging. However, the prevalence of premature ejaculation seems to be slightly higher than in other parts of the world. Teixeira T, Nazima M, Hallak J. Male Sexual Quality Of Life Is Maintained Satisfactorily Throughout Life In The Amazon Rainforest. Sex Med 2018;6:90-96. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Variation in the utilization of reconstruction following mastectomy in elderly women.

PubMed

In, Haejin; Jiang, Wei; Lipsitz, Stuart R; Neville, Bridget A; Weeks, Jane C; Greenberg, Caprice C

2013-06-01

Regardless of their age, women who choose to undergo postmastectomy reconstruction report improved quality of life as a result. However, actual use of reconstruction decreases with increasing age. Whereas this may reflect patient preference and clinical factors, it may also represent age-based disparity. Women aged 65 years or older who underwent mastectomy for DCIS/stage I/II breast cancer (2000-2005) were identified in the SEER-Medicare database. Overall and institutional rates of reconstruction were calculated. Characteristics of hospitals with higher and lower rates of reconstruction were compared. Pseudo-R² statistics utilizing a patient-level logistic regression model estimated the relative contribution of institution and patient characteristics. A total of 19,234 patients at 716 institutions were examined. Overall, 6 % of elderly patients received reconstruction after mastectomy. Institutional rates ranged from zero to >40 %. Whereas 53 % of institutions performed no reconstruction on elderly patients, 5.6 % performed reconstructions on more than 20 %. Although patient characteristics (%ΔR² = 70 %), and especially age (%ΔR² = 34 %), were the primary determinants of reconstruction, institutional characteristics also explained some of the variation (%ΔR² = 16 %). This suggests that in addition to appropriate factors, including clinical characteristics and patient preferences, the use of reconstruction among older women also is influenced by the institution at which they receive care. Variation in the likelihood of reconstruction by institution and the association with structural characteristics suggests unequal access to this critical component of breast cancer care. Increased awareness of a potential age disparity is an important first step to improve access for elderly women who are candidates and desire reconstruction.

Variation in the Utilization of Reconstruction Following Mastectomy in Elderly Women

PubMed Central

In, Haejin; Jiang, Wei; Lipsitz, Stuart R.; Neville, Bridget A.; Weeks, Jane C.; Greenberg, Caprice C.

2014-01-01

Background Regardless of their age, women who choose to undergo postmastectomy reconstruction report improved quality of life as a result. However, actual use of reconstruction decreases with increasing age. Whereas this may reflect patient preference and clinical factors, it may also represent age-based disparity. Methods Women aged 65 years or older who underwent mastectomy for DCIS/stage I/II breast cancer (2000–2005) were identified in the SEER-Medicare database. Overall and institutional rates of reconstruction were calculated. Characteristics of hospitals with higher and lower rates of reconstruction were compared. Pseudo-R2 statistics utilizing a patient-level logistic regression model estimated the relative contribution of institution and patient characteristics. Results A total of 19,234 patients at 716 institutions were examined. Overall, 6 % of elderly patients received reconstruction after mastectomy. Institutional rates ranged from zero to >40 %. Whereas 53 % of institutions performed no reconstruction on elderly patients, 5.6 % performed reconstructions on more than 20 %. Although patient characteristics (%ΔR2 = 70 %), and especially age (%ΔR2 = 34 %), were the primary determinants of reconstruction, institutional characteristics also explained some of the variation (%ΔR2 = 16 %). This suggests that in addition to appropriate factors, including clinical characteristics and patient preferences, the use of reconstruction among older women also is influenced by the institution at which they receive care. Conclusions Variation in the likelihood of reconstruction by institution and the association with structural characteristics suggests unequal access to this critical component of breast cancer care. Increased awareness of a potential age disparity is an important first step to improve access for elderly women who are candidates and desire reconstruction. PMID:23263733

Contrast-to-noise ratio in magnification mammography: a Monte Carlo study

NASA Astrophysics Data System (ADS)

Koutalonis, M.; Delis, H.; Spyrou, G.; Costaridou, L.; Tzanakos, G.; Panayiotakis, G.

2007-06-01

Magnification views are a common way to perform a secondary examination when suspicious abnormalities are found in a screening mammogram. The visibility of microcalcifications and breast lesions is restricted by the compromise between the image quality and the absorbed dose. In this study, image quality characteristics in magnification mammography were evaluated based on Monte Carlo techniques. A breast phantom was utilized, simulating a homogeneous mixture of adipose and glandular tissue in various percentages of glandularity, containing inhomogeneities of various sizes and compositions. The effect of the magnification degree, breast glandularity, tube voltage and anode/filter material combination on image quality characteristics was investigated in terms of a contrast-to-noise ratio (CNR). A performance index PIν was introduced in order to study the overall performance of various anode/filter combinations under different exposure parameters. Results demonstrate that CNR is improved with the degree of magnification and degraded as the breast glandularity is increased. Degree of magnification 1.3 offers the best overall performance for most of the anode/filter combinations utilized. Under magnification conditions, the role of dose is demoted against the image quality, as magnification views are secondary, diagnostic examinations and not screening procedures oriented to non-symptomatic women. For decreased image quality weighting, some anode/filter combinations different from Mo/0.030mmMo can be utilized as they offer a similar performance index. However, if the desired weighting for the image quality is high, the Mo/0.030mmMo combination has the best overall performance.

Characteristics Desired in Clinical Data Warehouse for Biomedical Research

PubMed Central

Shin, Soo-Yong; Kim, Woo Sung

2014-01-01

Objectives Due to the unique characteristics of clinical data, clinical data warehouses (CDWs) have not been successful so far. Specifically, the use of CDWs for biomedical research has been relatively unsuccessful thus far. The characteristics necessary for the successful implementation and operation of a CDW for biomedical research have not clearly defined yet. Methods Three examples of CDWs were reviewed: a multipurpose CDW in a hospital, a CDW for independent multi-institutional research, and a CDW for research use in an institution. After reviewing the three CDW examples, we propose some key characteristics needed in a CDW for biomedical research. Results A CDW for research should include an honest broker system and an Institutional Review Board approval interface to comply with governmental regulations. It should also include a simple query interface, an anonymized data review tool, and a data extraction tool. Also, it should be a biomedical research platform for data repository use as well as data analysis. Conclusions The proposed characteristics desired in a CDW may have limited transfer value to organizations in other countries. However, these analysis results are still valid in Korea, and we have developed clinical research data warehouse based on these desiderata. PMID:24872909

[Atypical polypoid adenomyoma of the uterus: a clinicopathological review of 27 cases].

PubMed

Bai, T J; Bao, D M; Li, Y; Wang, Y; Cui, H; Zhu, H L

2017-04-25

Objective: To investigate the clinical and pathological characteristics of atypical polypoid adenomyoma (APA) for improvement of the diagnosis, different diagnosis and treatment of the disease. Methods: The clinical data, pathological characteristics, and the follow-up information were retrospectively analyzed in 27 cases of APA admitted in Peking Univeristy People ' s Hospital from 2007 to 2016. Results: The median age was 42.6 years old (range 25-60 years old). Fifteen patients were nullipara, 2 patients were postmenopausal. The most common presenting symptom was abnormal uterine bleeding (81%, 22/27) . Leisions were obtained by using hysteroscopy in 23 cases, hysterectomy 3 cases and dilatation and curettage 1 case. Fertility preserving treatments were performed in 10 patients who had strong desire for fertility, among which 1 case progressed into endometrial carcinoma. Among 15 patients underwent hysterectomy and (or) bilateral salpingo-oophorectomy, 9 cases of them had endometrial atypical hyperplasia. Endometrial carcinoma along with APA were found in three patients, 2 cases of them underwent hysterectomy and bilateral salpingo-oophorectomy and pelvic lymphadenectomy, the other one received medication for fertility preservation. Follow up information were available in 24 cases (89%, 24/27) with a median follow up of 46 months (range 4-108 months), 1 case recurred and 1 case progressed into endometrial carcinoma. One case died of other malignancy, while the other patients were alive. Conclusions: APA is a rare uterine neoplasm mixed with epithelial and mesenchymal component. It occurs mostly in childbearing-age women and its diagnosis is dependent on pathology. Although it ' s clinical course is benign, there is risk of co-existance of endometrial carcinoma and endometrial atypical hyperplasia. For those who has desire of fertility, the treatment strategy is completely removed the lesion and closely followed up. For those who do not desire to preserve fertility, hysterectomy may be an option.

Association between parenting practices and children's dietary intake, activity behavior and development of body mass index: the KOALA Birth Cohort Study

PubMed Central

2011-01-01

Background Insights into the effects of energy balance-related parenting practices on children's diet and activity behavior at an early age is warranted to determine which practices should be recommended and to whom. The purpose of this study was to examine child and parent background correlates of energy balance-related parenting practices at age 5, as well as the associations of these practices with children's diet, activity behavior, and body mass index (BMI) development. Methods Questionnaire data originated from the KOALA Birth Cohort Study for ages 5 (N = 2026) and 7 (N = 1819). Linear regression analyses were used to examine the association of child and parent background characteristics with parenting practices (i.e., diet- and activity-related restriction, monitoring and stimulation), and to examine the associations between these parenting practices and children's diet (in terms of energy intake, dietary fiber intake, and added sugar intake) and activity behavior (i.e., physical activity and sedentary time) at age 5, as well as BMI development from age 5 to age 7. Moderation analyses were used to examine whether the associations between the parenting practices and child behavior depended on child characteristics. Results Several child and parent background characteristics were associated with the parenting practices. Dietary monitoring, stimulation of healthy intake and stimulation of physical activity were associated with desirable energy balance-related behaviors (i.e., dietary intake and/or activity behavior) and desirable BMI development, whereas restriction of sedentary time showed associations with undesirable behaviors and BMI development. Child eating style and weight status, but not child gender or activity style, moderated the associations between parenting practices and behavior. Dietary restriction and monitoring showed weaker, or even undesirable associations for children with a deviant eating style, whereas these practices showed associations with desirable behavior for normal eaters. By contrast, stimulation to eat healthy worked particularly well for children with a deviant eating style or a high BMI. Conclusion Although most energy balance-related parenting practices were associated with desirable behaviors, some practices showed associations with undesirable child behavior and weight outcomes. Only parental stimulation showed desirable associations with regard to both diet and activity behavior. The interaction between parenting and child characteristics in the association with behavior calls for parenting that is tailored to the individual child. PMID:21401954

Association between parenting practices and children's dietary intake, activity behavior and development of body mass index: the KOALA Birth Cohort Study.

PubMed

Gubbels, Jessica S; Kremers, Stef P J; Stafleu, Annette; de Vries, Sanne I; Goldbohm, R Alexandra; Dagnelie, Pieter C; de Vries, Nanne K; van Buuren, Stef; Thijs, Carel

2011-03-14

Insights into the effects of energy balance-related parenting practices on children's diet and activity behavior at an early age is warranted to determine which practices should be recommended and to whom. The purpose of this study was to examine child and parent background correlates of energy balance-related parenting practices at age 5, as well as the associations of these practices with children's diet, activity behavior, and body mass index (BMI) development. Questionnaire data originated from the KOALA Birth Cohort Study for ages 5 (N = 2026) and 7 (N = 1819). Linear regression analyses were used to examine the association of child and parent background characteristics with parenting practices (i.e., diet- and activity-related restriction, monitoring and stimulation), and to examine the associations between these parenting practices and children's diet (in terms of energy intake, dietary fiber intake, and added sugar intake) and activity behavior (i.e., physical activity and sedentary time) at age 5, as well as BMI development from age 5 to age 7. Moderation analyses were used to examine whether the associations between the parenting practices and child behavior depended on child characteristics. Several child and parent background characteristics were associated with the parenting practices. Dietary monitoring, stimulation of healthy intake and stimulation of physical activity were associated with desirable energy balance-related behaviors (i.e., dietary intake and/or activity behavior) and desirable BMI development, whereas restriction of sedentary time showed associations with undesirable behaviors and BMI development. Child eating style and weight status, but not child gender or activity style, moderated the associations between parenting practices and behavior. Dietary restriction and monitoring showed weaker, or even undesirable associations for children with a deviant eating style, whereas these practices showed associations with desirable behavior for normal eaters. By contrast, stimulation to eat healthy worked particularly well for children with a deviant eating style or a high BMI. Although most energy balance-related parenting practices were associated with desirable behaviors, some practices showed associations with undesirable child behavior and weight outcomes. Only parental stimulation showed desirable associations with regard to both diet and activity behavior. The interaction between parenting and child characteristics in the association with behavior calls for parenting that is tailored to the individual child.

Novel hybrid isotope separation scheme and apparatus

DOEpatents

Maya, J.

1991-06-18

A method is described for yielding selectively a desired enrichment in a specific isotope including the steps of inputting into a spinning chamber a gas from which the specific isotope is to be isolated, radiating the gas with frequencies characteristic of the absorption of a particular isotope of the atomic or molecular gas, thereby inducing a photoionization reaction of the desired isotope, and collecting the specific isotope ion by suitable ion collection means. 3 figures.

Apodised aperture using rotation of plane of polarization

DOEpatents

Simmons, W.W.; Leppelmeier, G.W.; Johnson, B.C.

1975-09-01

An apodised aperture based on the rotation of plane of polarization producing desirable characteristics on a transmitted light beam such as beam profiling in high flux laser amplifier chains is described. The apodised aperture is made with a lossless element by using one or more polarizers and/or analyzers and magneto-optical Faraday means for selectively rotating the plane of polarized radiation over the cross section to effect the desired apodisation. (auth)

Routing performance analysis and optimization within a massively parallel computer

DOEpatents

Archer, Charles Jens; Peters, Amanda; Pinnow, Kurt Walter; Swartz, Brent Allen

2013-04-16

An apparatus, program product and method optimize the operation of a massively parallel computer system by, in part, receiving actual performance data concerning an application executed by the plurality of interconnected nodes, and analyzing the actual performance data to identify an actual performance pattern. A desired performance pattern may be determined for the application, and an algorithm may be selected from among a plurality of algorithms stored within a memory, the algorithm being configured to achieve the desired performance pattern based on the actual performance data.

Correlation among commercial traits and the possible maternal effects for these traits in the reciprocal populations of Atlantic and Superior

USDA-ARS?s Scientific Manuscript database

Reciprocal populations of Atlantic and Superior were created with the objective of combining the desired traits of the two parents and selecting a new variety with similar characteristics as Atlantic but with improved internal quality. Both parents have contrasting characteristics for yield, specifi...

The Shaping of Professional Subcultures: A Study of Student Groups from Five Professions.

ERIC Educational Resources Information Center

Walther, Regis H.; And Others

This paper discusses the processes that determine the characteristics of professional sub-cultures. It was postulated that mechanisms of attraction, formal and informal selection, promotion and reinforcement of desired characteristics serve to shape the personality which characterizes the members of a profession and can be expected to result in a…

Character Strengths Are Prominent as Mate Preferences of Turkish Students

ERIC Educational Resources Information Center

White, Elizabeth Michelle; Pearce, Amy R.; Khramtsova, Irina

2011-01-01

This study addressed the traits and characteristics that Turkish students deem most important in a long-term romantic partner. We collected quantitative and qualitative data on characteristics desired in romantic partners from students attending Bahçesehir Üniversitesi in Istanbul, Turkey. Like our previous cross-cultural studies conducted in…

Give Better Feedback on Engineering Drawings

ERIC Educational Resources Information Center

Cobb, Robert, Jr.; Graham, Tony; Kapur, Arjun; Rhodes, Craig; Blackwell, Ellinor

2005-01-01

Most, if not all, systems have a mechanism that collects information to facilitate monitoring performance. This information is primarily used to modify the system to make it more efficient in performing desired tasks and, thus, attaining desired results. Similar to electrical, mechanical, or hydraulic systems, the feedback mechanism in an…

Plasma-sprayed self-lubricating coatings

NASA Technical Reports Server (NTRS)

Nakamura, H. H.; Logan, W. R.; Harada, Y.

1982-01-01

One of the most important criterion for acceptable commercial application of a multiple phase composition is uniformity and reproducibility. This means that the performance characteristics of the coat - e.g., its lubricating properties, bond strength to the substrate, and thermal properties - can be readily predicted to give a desired performance. The improvement of uniformity and reproducibility of the coats, the oxidation behavior at three temperature ranges, the effect of bond coat and the effect of preheat treatment as measured by adhesive strength tests, coating examination procedures, and physical property measurements were studied. The following modifications improved the uniformity and reproducibility: (1) changes and closer control in the particle size range of the raw materials used, (2) increasing the binder content from 3.2% to 4.1% (dried weight), and (3) analytical processing procedures using step by step checking to assure consistency.

Coupled parametric design of flow control and duct shape

NASA Technical Reports Server (NTRS)

Florea, Razvan (Inventor); Bertuccioli, Luca (Inventor)

2009-01-01

A method for designing gas turbine engine components using a coupled parametric analysis of part geometry and flow control is disclosed. Included are the steps of parametrically defining the geometry of the duct wall shape, parametrically defining one or more flow control actuators in the duct wall, measuring a plurality of performance parameters or metrics (e.g., flow characteristics) of the duct and comparing the results of the measurement with desired or target parameters, and selecting the optimal duct geometry and flow control for at least a portion of the duct, the selection process including evaluating the plurality of performance metrics in a pareto analysis. The use of this method in the design of inter-turbine transition ducts, serpentine ducts, inlets, diffusers, and similar components provides a design which reduces pressure losses and flow profile distortions.

Development of a Probabilistic Dynamic Synthesis Method for the Analysis of Nondeterministic Structures

NASA Technical Reports Server (NTRS)

Brown, A. M.

1998-01-01

Accounting for the statistical geometric and material variability of structures in analysis has been a topic of considerable research for the last 30 years. The determination of quantifiable measures of statistical probability of a desired response variable, such as natural frequency, maximum displacement, or stress, to replace experience-based "safety factors" has been a primary goal of these studies. There are, however, several problems associated with their satisfactory application to realistic structures, such as bladed disks in turbomachinery. These include the accurate definition of the input random variables (rv's), the large size of the finite element models frequently used to simulate these structures, which makes even a single deterministic analysis expensive, and accurate generation of the cumulative distribution function (CDF) necessary to obtain the probability of the desired response variables. The research presented here applies a methodology called probabilistic dynamic synthesis (PDS) to solve these problems. The PDS method uses dynamic characteristics of substructures measured from modal test as the input rv's, rather than "primitive" rv's such as material or geometric uncertainties. These dynamic characteristics, which are the free-free eigenvalues, eigenvectors, and residual flexibility (RF), are readily measured and for many substructures, a reasonable sample set of these measurements can be obtained. The statistics for these rv's accurately account for the entire random character of the substructure. Using the RF method of component mode synthesis, these dynamic characteristics are used to generate reduced-size sample models of the substructures, which are then coupled to form system models. These sample models are used to obtain the CDF of the response variable by either applying Monte Carlo simulation or by generating data points for use in the response surface reliability method, which can perform the probabilistic analysis with an order of magnitude less computational effort. Both free- and forced-response analyses have been performed, and the results indicate that, while there is considerable room for improvement, the method produces usable and more representative solutions for the design of realistic structures with a substantial savings in computer time.

The Association of Eating Performance and Environmental Stimulation among Older Adults with Dementia in Nursing Homes: A Secondary Analysis

PubMed Central

Liu, Wen; Jao, Ying-Ling; Williams, Kristine

2017-01-01

Background Nursing home residents with dementia experience increased risk for compromised eating performance due to intrapersonal, interpersonal, and environmental factors. Environmental stimulation is physical, social, and/or sensory stimulation present in the environment that can potentially trigger individuals’ emotion or motivate physical reactions. Beyond the personal factors, there is a lack of evidence on how environmental stimulation influences individuals’ eating performance at mealtimes. Objectives This study examined the association between environmental stimulation and eating performance among nursing home residents with dementia. Design This study was a secondary analysis using baseline videos selected from a communication intervention study, where videos were recorded to capture staff-resident interactions during care activities for nursing home residents with dementia. Videos were included in this study only if residents demonstrated eating activities at mealtimes. Sample and Setting A total of 36 videos were selected (mean length = 4 minutes). The sample included 15 residents with dementia (mean age = 86), and 19 certified nursing assistants (mean age = 36) in 8 nursing homes. Methods The dependent variable was eating performance as measured by the Level of Eating Independence scale (range: 15–36, with higher scores indicating better eating performance). The independent variables were characteristics of environmental stimulation measured by the Person-Environment Apathy Rating-Environment subscale (stimulation clarity, stimulation strength, stimulation specificity, interaction involvement, physical accessibility, and environmental feedback). Each characteristic was rated on a 1–4 scale with higher scores indicating more desirable environmental stimulation. Multilevel models were used to examine the association between eating performance and environmental stimulation, adjusting for resident characteristics (i.e., age, gender, dementia stage, function, comorbidity, psychoactive medication use) and nesting effects of residents and staff. Results Resident participants demonstrated moderate levels of eating performance (M=27.08, SD = 5.16). Eating performance was significantly lower among older residents, those with more advanced dementia, and higher comorbidity. After controlling for resident characteristics, eating performance was significantly associated with stimulation specificity (how the stimulation is delivered and tailored to the resident), and was not associated with other environmental stimulation characteristics. For each 1 point increase in stimulation specificity, eating performance increased by 8.78 points (95% CI=.59, 16.97). Conclusions Environmental stimulation that is personally tailored to a resident’ needs and preferences and directly offered to a resident contributed to better eating performance among residents with dementia. The findings will direct future development and implementation of person-directed mealtime care programs and dining environment arrangements for residents with dementia in nursing homes. PMID:28340390

The association of eating performance and environmental stimulation among older adults with dementia in nursing homes: A secondary analysis.

PubMed

Liu, Wen; Jao, Ying-Ling; Williams, Kristine

2017-06-01

Nursing home residents with dementia experience increased risk for compromised eating performance due to intrapersonal, interpersonal, and environmental factors. Environmental stimulation is physical, social, and/or sensory stimulation present in the environment that can potentially trigger individuals' emotion or motivate physical reactions. Beyond the personal factors, there is a lack of evidence on how environmental stimulation influences individuals' eating performance at mealtimes. This study examined the association between environmental stimulation and eating performance among nursing home residents with dementia. This study was a secondary analysis using baseline videos selected from a communication intervention study, where videos were recorded to capture staff-resident interactions during care activities for nursing home residents with dementia. Videos were included in this study only if residents demonstrated eating activities at mealtimes. A total of 36 videos were selected (mean length=4min). The sample included 15 residents with dementia (mean age=86), and 19 certified nursing assistants (mean age=36) in 8 nursing homes. The dependent variable was eating performance as measured by the Level of Eating Independence scale (range: 15-36, with higher scores indicating better eating performance). The independent variables were characteristics of environmental stimulation measured by the Person-Environment Apathy Rating-Environment subscale (stimulation clarity, stimulation strength, stimulation specificity, interaction involvement, physical accessibility, and environmental feedback). Each characteristic was rated on a 1-4 scale with higher scores indicating more desirable environmental stimulation. Multilevel models were used to examine the association between eating performance and environmental stimulation, adjusting for resident characteristics (i.e., age, gender, dementia stage, function, comorbidity, psychoactive medication use) and nesting effects of residents and staff. Resident participants demonstrated moderate levels of eating performance (M=27.08, SD=5.16). Eating performance was significantly lower among older residents, those with more advanced dementia, and higher comorbidity. After controlling for resident characteristics, eating performance was significantly associated with stimulation specificity (how the stimulation is delivered and tailored to the resident), and was not associated with other environmental stimulation characteristics. For each 1 point increase in stimulation specificity, eating performance increased by 8.78 points (95% CI=0.59, 16.97). Environmental stimulation that is personally tailored to a resident' needs and preferences and directly offered to a resident contributed to better eating performance among residents with dementia. The findings will direct future development and implementation of person-directed mealtime care programs and dining environment arrangements for residents with dementia in nursing homes. Copyright © 2017 Elsevier Ltd. All rights reserved.

SULTAN measurement and qualification: ITER-US-LLNL-NMARTOVETSKY- 092008

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martovetsky, N N

2006-09-21

Measuring the characteristics of full scale ITER CICC at SULTAN is the critical qualification test. If volt-ampere characteristic (VAC) or volt-temperature characteristic (VTC) are distorted, the criterion of 10 uV/m may not be a valid criterion to judge the conductor performance. Only measurements with a clear absence or low signals from the current distribution should be considered as quantitatively representative, although in some obvious circumstances one can judge if a conductor will meet or fail ITER requirements. SULTAN full scale ITER CICC testing should be done with all measures taken to ensure uniform current redistribution. A full removal of Crmore » plating in the joint area and complete solder filling of the joints (with provision of the central channel for helium flow) should be mandatory for DC qualification samples for ITER. Also, T and I should be increased slowly that an equilibrium could be established for accurate measurement of Tcs, Ic and N. It is also desirable to go up in down in current and/or temperature (within stable range) to make sure that the equilibrium is reached.« less

Characteristics of women who frequently under report their energy intake: a doubly labelled water study.

PubMed

Scagliusi, F B; Ferriolli, E; Pfrimer, K; Laureano, C; Cunha, C S F; Gualano, B; Lourenço, B H; Lancha, A H

2009-10-01

We applied three dietary assessment methods and aimed at obtaining a set of physical, social and psychological variables that can discriminate those individuals who did not underreport ('never under-reporters'), those who underreported in one dietary assessment method ('occasional under-reporters') and those who underreported in two or three dietary assessment methods ('frequent under-reporters'). Sixty-five women aged 18-57 years were recruited for this study. Total energy expenditure was determined by doubly labelled water, and energy intake was estimated by three 24-h diet recalls, 3-day food records and a food frequency questionnaire. A multiple discriminant analysis was used to identify which of those variables better discriminated the three groups: body mass index (BMI), income, education, social desirability, nutritional knowledge, dietary restraint, physical activity practice, body dissatisfaction and binge-eating symptoms. Twenty-three participants were 'never under-reporters'. Twenty-four participants were 'occasional under-reporters' and 18 were 'frequent under-reporters'. Four variables entered the discriminant model: income, BMI, social desirability and body dissatisfaction. According to potency indices, income contributed the most to the total discriminant power, followed in decreasing order by social desirability score, BMI and body dissatisfaction. Income, social desirability and BMI were the characteristics that mainly separated the 'never under-reporters' from the under-reporters (occasional or frequent). Body dissatisfaction better discriminated the 'occasional under-reporters' from the 'frequent under-reporters'. 'Frequent under-reporters' have a greater BMI, social desirability score, body dissatisfaction score and lower income. These four variables seemed to be able to discriminate individuals who are more prone to systematic under reporting.

Investigation of the Behavioral Characteristics of Dogs Purpose-Bred and Prepared to Perform Vapor Wake® Detection of Person-Borne Explosives

PubMed Central

Lazarowski, Lucia; Haney, Pamela Sue; Brock, Jeanne; Fischer, Terry; Rogers, Bart; Angle, Craig; Katz, Jeffrey S.; Waggoner, L. Paul

2018-01-01

Specialized detector dogs are increasingly being utilized for the detection of modern threats. The Vapor Wake® (VW) dog was developed to create a dog phenotype ideally suited for detecting hand-carried and body-worn explosives. VW dogs (VWDs) are trained to sample and alert to target odors in the aerodynamic wakes of moving persons, which entrains vapor and small particles from the person. The behavioral characteristics necessary for dogs to be successfully trained and employed for the application of VW are a distinct subset of the desired general characteristics of dogs used for detection tasks due to the dynamic nature of moving targets. The purpose of this study was to examine the behavioral characteristics of candidate detector dogs to determine the particular qualities that set apart VW-capable dogs from others. We assessed 146 candidate detector dogs from a VW breeding and training program. Dogs received identical puppy development and foundational odor training and underwent performance evaluations at 3, 6, 10, and 12 months old, after which they were sold for service. Dogs were categorized based on their final outcome of the training program, independently determined by private vendors, corresponding to three groups: dogs successfully sold for VW, dogs sold for standard explosives detection, and dogs that failed to be placed in any type of detector dog service (Washouts). Comparisons of behavioral evaluations between the groups were made across domains pertaining to search-related behaviors (Performance), reactions to novel stimuli (Environmental), and overall ease of learning new tasks (Trainability). Comparisons were also made at each evaluation to determine any early emergence of differences. VWDs scored significantly higher on Performance characteristics compared to standard explosives detection dogs (EDDs) and Washouts. However, Environmental characteristics did not differentiate VWDs from EDDs, though scores on these measures were significantly lower in the Washouts. Furthermore, differences between groups emerged as early as 3 and 6 months for select measures. We describe the behavioral characteristics targeted for selection in developing the VW phenotype and discuss the relative merit and degree of expression of those characteristics in the success of dogs bred and trained for the VW application. PMID:29616229

Rational design of hierarchically porous birnessite-type manganese dioxides nanosheets on different one-dimensional titania-based nanowires for high performance supercapacitors

NASA Astrophysics Data System (ADS)

Zhang, Yu Xin; Kuang, Min; Hao, Xiao Dong; Liu, Yan; Huang, Ming; Guo, Xiao Long; Yan, Jing; Han, Gen Quan; Li, Jing

2014-12-01

A facile and large-scale strategy of mesoporous birnessite-type manganese dioxide (MnO2) nanosheets on one-dimension (1D) H2Ti3O7 and anatase/TiO2 (B) nanowires (NWs) is developed for high performance supercapacitors. The morphological characteristics of MnO2 nanoflakes on H2Ti3O7 and anatase/TiO2 (B) NWs could be rationally designed with various characteristics (e.g., the sheet thickness, surface area). Interestingly, the MnO2/TiO2 NWs exhibit a more optimized electrochemical performance with specific capacitance of 120 F g-1 at current density of 0.1 A g-1 (based on MnO2 + TiO2) than MnO2/H2Ti3O7 NWs. An asymmetric supercapacitor of MnO2/TiO2//activated graphene (AG) yields a better energy density of 29.8 Wh kg-1 than MnO2/H2Ti3O7//AG asymmetric supercapacitor, while maintaining desirable cycling stability. Indeed, the pseudocapacitive difference is related to the substrates, unique structure and surface area. Especially, the anatase/TiO2 (B) mixed-phase system can provide good electronic conductivity and high utilization of MnO2 nanosheets.

CMAS Degradation of Environmental Barrier Coatings: Mechanisms and Mitigation

DTIC Science & Technology

2013-09-30

enable it to grow an EBC-like scale , i.e. resistant to volatilization, when exposed directly to the oxidative environment at places where the original...CAD) methods. It was shown that formulations based on SiC/YB2/Y5Si3/AI203 produced scales with the desirable characteristics, comprising primarily...oxidizing surface, which could be desirable in crack healing scenarios but led to excessive thick scales . When density was improved by CAD the Y

U.S. consumer demand for restaurant calorie information: targeting demographic and behavioral segments in labeling initiatives.

PubMed

Kolodinsky, Jane; Reynolds, Travis William; Cannella, Mark; Timmons, David; Bromberg, Daniel

2009-01-01

To identify different segments of U.S. consumers based on food choices, exercise patterns, and desire for restaurant calorie labeling. Using a stratified (by region) random sample of the U.S. population, trained interviewers collected data for this cross-sectional study through telephone surveys. Center for Rural Studies U.S. national health survey. The final sample included 580 responses (22% response rate); data were weighted to be representative of age and gender characteristics of the U.S. population. Self-reported behaviors related to food choices, exercise patterns, desire for calorie information in restaurants, and sample demographics. Clusters were identified using Schwartz Bayesian criteria. Impacts of demographic characteristics on cluster membership were analyzed using bivariate tests of association and multinomial logit regression. Cluster analysis revealed three clusters based on respondents' food choices, activity levels, and desire for restaurant labeling. Two clusters, comprising three quarters of the sample, desired calorie labeling in restaurants. The remaining cluster opposed restaurant labeling. Demographic variables significantly predicting cluster membership included region of residence (p < .10), income (p < .05), gender (p < .01), and age (p < .10). Though limited by a low response and potential self-reporting bias in the phone survey, this study suggests that several groups are likely to benefit from restaurant calorie labeling. Specific demographic clusters could be targeted through labeling initiatives.

Method and system for SCR optimization

DOEpatents

Lefebvre, Wesley Curt [Boston, MA; Kohn, Daniel W [Cambridge, MA

2009-03-10

Methods and systems are provided for controlling SCR performance in a boiler. The boiler includes one or more generally cross sectional areas. Each cross sectional area can be characterized by one or more profiles of one or more conditions affecting SCR performance and be associated with one or more adjustable desired profiles of the one or more conditions during the operation of the boiler. The performance of the boiler can be characterized by boiler performance parameters. A system in accordance with one or more embodiments of the invention can include a controller input for receiving a performance goal for the boiler corresponding to at least one of the boiler performance parameters and for receiving data values corresponding to boiler control variables and to the boiler performance parameters. The boiler control variables include one or more current profiles of the one or more conditions. The system also includes a system model that relates one or more profiles of the one or more conditions in the boiler to the boiler performance parameters. The system also includes an indirect controller that determines one or more desired profiles of the one or more conditions to satisfy the performance goal for the boiler. The indirect controller uses the system model, the received data values and the received performance goal to determine the one or more desired profiles of the one or more conditions. The system model also includes a controller output that outputs the one or more desired profiles of the one or more conditions.

Assessing food appeal and desire to eat: the effects of portion size & energy density

PubMed Central

2011-01-01

Background Visual presentation of food provides considerable information such as its potential for palatability and availability, both of which can impact eating behavior. Methods We investigated the subjective ratings for food appeal and desire to eat when exposed to food pictures in a fed sample (n = 129) using the computer paradigm ImageRate. Food appeal and desire to eat were analyzed for the effects of food group, portion size and energy density of the foods presented as well as by participant characteristics. Results Food appeal ratings were significantly higher than those for desire to eat (57.9 ± 11.6 v. 44.7 ± 18.0; p < 0.05). Body mass index was positively correlated to desire to eat (r = 0.20; p < 0.05), but not food appeal. Food category analyses revealed that fruit was the highest rated food category for both appeal and desire, followed by discretionary foods. Additionally, overweight individuals reported higher ratings of desire to eat large portions of food compared to smaller portions (p < 0.001), although these effects were relatively small. Energy density of the foods was inversely correlated with ratings for both appeal and desire (r's = - 0.27; p's < 0.01). Conclusions Results support the hypothesis that individuals differentiate between food appeal and desire to eat foods when assessing these ratings using the same type of metric. Additionally, relations among food appeal and desire to eat ratings and body mass show overweight individuals could be more responsive to visual foods cues in a manner that contributes to obesity. PMID:21943082

Assessing food appeal and desire to eat: the effects of portion size & energy density.

PubMed

Burger, Kyle S; Cornier, Marc A; Ingebrigtsen, Jan; Johnson, Susan L

2011-09-25

Visual presentation of food provides considerable information such as its potential for palatability and availability, both of which can impact eating behavior. We investigated the subjective ratings for food appeal and desire to eat when exposed to food pictures in a fed sample (n=129) using the computer paradigm ImageRate. Food appeal and desire to eat were analyzed for the effects of food group, portion size and energy density of the foods presented as well as by participant characteristics. Food appeal ratings were significantly higher than those for desire to eat (57.9±11.6 v. 44.7±18.0; p<0.05). Body mass index was positively correlated to desire to eat (r=0.20; p<0.05), but not food appeal. Food category analyses revealed that fruit was the highest rated food category for both appeal and desire, followed by discretionary foods. Additionally, overweight individuals reported higher ratings of desire to eat large portions of food compared to smaller portions (p<0.001), although these effects were relatively small. Energy density of the foods was inversely correlated with ratings for both appeal and desire (r's=-0.27; p's<0.01). Results support the hypothesis that individuals differentiate between food appeal and desire to eat foods when assessing these ratings using the same type of metric. Additionally, relations among food appeal and desire to eat ratings and body mass show overweight individuals could be more responsive to visual foods cues in a manner that contributes to obesity.

Free-standing three-dimensional graphene/manganese oxide hybrids as binder-free electrode materials for energy storage applications.

PubMed

Zhu, Xiaoli; Zhang, Peng; Xu, Shan; Yan, Xingbin; Xue, Qunji

2014-07-23

Novel three-dimensional (3D) hybrid materials, i.e., free-standing 3D graphene-supported MnO2 nanosheets, are prepared by a simple and controllable solution-phase assembly process. Characterization results show that MnO2 nanosheets are uniformly anchored on a 3D graphene framework with strong adhesion and the integral hybrids show desirable mechanical strength. Such unique structure of 3D graphene/MnO2 hybrids thus provides the right characteristics of binder-free electrode materials and could enable the design of different kinds of high-performance energy storage devices. Especially, an advanced asymmetric supercapacitor is built by using a 3D graphene/MnO2 hybrid and a 3D graphene as two electrodes, and it is able to work reversibly in a full operation voltage region of 0-3.5 V in an ionic liquid electrolyte and thus exhibits a high energy density of 68.4 Wh/kg. As the cathode materials for Li-O2 and Li-MnO2 batteries, the 3D graphene/MnO2 hybrids exhibit outstanding performances, including good catalytic capability, high reversible capacity and desirable cycling stability. The results presented here may pave a way for new promising applications of such 3D graphene/MnO2 hybrids in advanced electrochemical energy storage devices.

Advancing the LSST Operations Simulator

NASA Astrophysics Data System (ADS)

Saha, Abhijit; Ridgway, S. T.; Cook, K. H.; Delgado, F.; Chandrasekharan, S.; Petry, C. E.; Operations Simulator Group

2013-01-01

The Operations Simulator for the Large Synoptic Survey Telescope (LSST; http://lsst.org) allows the planning of LSST observations that obey explicit science driven observing specifications, patterns, schema, and priorities, while optimizing against the constraints placed by design-specific opto-mechanical system performance of the telescope facility, site specific conditions (including weather and seeing), as well as additional scheduled and unscheduled downtime. A simulation run records the characteristics of all observations (e.g., epoch, sky position, seeing, sky brightness) in a MySQL database, which can be queried for any desired purpose. Derivative information digests of the observing history database are made with an analysis package called Simulation Survey Tools for Analysis and Reporting (SSTAR). Merit functions and metrics have been designed to examine how suitable a specific simulation run is for several different science applications. This poster reports recent work which has focussed on an architectural restructuring of the code that will allow us to a) use "look-ahead" strategies that avoid cadence sequences that cannot be completed due to observing constraints; and b) examine alternate optimization strategies, so that the most efficient scheduling algorithm(s) can be identified and used: even few-percent efficiency gains will create substantive scientific opportunity. The enhanced simulator will be used to assess the feasibility of desired observing cadences, study the impact of changing science program priorities, and assist with performance margin investigations of the LSST system.

Design and construction of a first-generation high-throughput integrated robotic molecular biology platform for bioenergy applications.

PubMed

Hughes, Stephen R; Butt, Tauseef R; Bartolett, Scott; Riedmuller, Steven B; Farrelly, Philip

2011-08-01

The molecular biological techniques for plasmid-based assembly and cloning of gene open reading frames are essential for elucidating the function of the proteins encoded by the genes. High-throughput integrated robotic molecular biology platforms that have the capacity to rapidly clone and express heterologous gene open reading frames in bacteria and yeast and to screen large numbers of expressed proteins for optimized function are an important technology for improving microbial strains for biofuel production. The process involves the production of full-length complementary DNA libraries as a source of plasmid-based clones to express the desired proteins in active form for determination of their functions. Proteins that were identified by high-throughput screening as having desired characteristics are overexpressed in microbes to enable them to perform functions that will allow more cost-effective and sustainable production of biofuels. Because the plasmid libraries are composed of several thousand unique genes, automation of the process is essential. This review describes the design and implementation of an automated integrated programmable robotic workcell capable of producing complementary DNA libraries, colony picking, isolating plasmid DNA, transforming yeast and bacteria, expressing protein, and performing appropriate functional assays. These operations will allow tailoring microbial strains to use renewable feedstocks for production of biofuels, bioderived chemicals, fertilizers, and other coproducts for profitable and sustainable biorefineries. Published by Elsevier Inc.

Control of a high beta maneuvering reentry vehicle using dynamic inversion.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watts, Alfred Chapman

2005-05-01

The design of flight control systems for high performance maneuvering reentry vehicles presents a significant challenge to the control systems designer. These vehicles typically have a much higher ballistic coefficient than crewed vehicles like as the Space Shuttle or proposed crew return vehicles such as the X-38. Moreover, the missions of high performance vehicles usually require a steeper reentry flight path angle, followed by a pull-out into level flight. These vehicles then must transit the entire atmosphere and robustly perform the maneuvers required for the mission. The vehicles must also be flown with small static margins in order to performmore » the required maneuvers, which can result in highly nonlinear aerodynamic characteristics that frequently transition from being aerodynamically stable to unstable as angle of attack increases. The control system design technique of dynamic inversion has been applied successfully to both high performance aircraft and low beta reentry vehicles. The objective of this study was to explore the application of this technique to high performance maneuvering reentry vehicles, including the basic derivation of the dynamic inversion technique, followed by the extension of that technique to the use of tabular trim aerodynamic models in the controller. The dynamic inversion equations are developed for high performance vehicles and augmented to allow the selection of a desired response for the control system. A six degree of freedom simulation is used to evaluate the performance of the dynamic inversion approach, and results for both nominal and off nominal aerodynamic characteristics are presented.« less

Kinematic functions for redundancy resolution using configuration control

NASA Technical Reports Server (NTRS)

Seraji, Homayoun (Inventor)

1994-01-01

The invention fulfills new goals for redundancy resolution based on manipulator dynamics and end-effector characteristics. These goals are accomplished by employing the recently developed configuration control approach. Redundancy resolution is achieved by controlling the joint inertia matrix of the end-effector mass matrix that affect the inertial torques or by reducing the joint torques due to gravity loading and payload. The manipulator mechanical-advantage and velocity-ratio are also used as performance measures to be improved by proper utilization of redundancy. Furthermore, end-effector compliance, sensitivity, and impulsive force at impact are introduced as redundancy resolution criteria. The new goals for redundancy resolution allow a more efficient utilization of the redundant joints based on the desired task requirements.

FPGA implementation of current-sharing strategy for parallel-connected SEPICs

NASA Astrophysics Data System (ADS)

Ezhilarasi, A.; Ramaswamy, M.

2016-01-01

The attempt echoes to evolve an equal current-sharing algorithm over a number of single-ended primary inductance converters connected in parallel. The methodology involves the development of state-space model to predict the condition for the existence of a stable equilibrium portrait. It acquires the role of a variable structure controller to guide the trajectory, with a view to circumvent the circuit non-linearities and arrive at a stable performance through a preferred operating range. The design elicits an acceptable servo and regulatory characteristics, the desired time response and ensures regulation of the load voltage. The simulation results validated through a field programmable gate array-based prototype serves to illustrate its suitability for present-day applications.

An RC active filter design handbook

NASA Technical Reports Server (NTRS)

Deboo, G. J.

1977-01-01

The design of filters is described. Emphasis is placed on simplified procedures that can be used by the reader who has minimum knowledge about circuit design and little acquaintance with filter theory. The handbook has three main parts. The first part is a review of some information that is essential for work with filters. The second part includes design information for specific types of filter circuitry and describes simple procedures for obtaining the component values for a filter that will have a desired set of characteristics. Pertinent information relating to actual performance is given. The third part (appendix) is a review of certain topics in filter theory and is intended to provide some basic understanding of how filters are designed.

Characteristics of a Broadband Dye Laser Using Pyrromethene and Rhodamine Dyes

NASA Technical Reports Server (NTRS)

Tedder, Sarah A.; Danehy, Paul M.; Wheeler, Jeffrey L.

2011-01-01

A broadband dye laser pumped by a frequency-doubled Nd:YAG laser with a full-width half-maximum (FWHM) from 592 to 610 nm was created for the use in a dual-pump broadband CARS system called WIDECARS. The desired broadband dye laser was generated with a mixture of Pyrromethene dyes as an oscillator gain medium and a spectral selective optic in the oscillator cavity. A mixture of Rhodamine dyes were used in the amplifier dye cell. To create this laser a study was performed to characterize the spectral behavior of broadband dye lasers created with Rhodamine dyes 590, 610, and 640, Pyrromethene dyes 597 and 650 as well as mixture of these dyes.

Induction heating apparatus and methods for selectively energizing an inductor in response to a measured electrical characteristic that is at least partially a function of a temperature of a material being heated

DOEpatents

Richardson, John G.; Morrison, John L.; Hawkes, Grant L.

2006-07-04

An induction heating apparatus includes a measurement device for indicating an electrical resistance of a material to be heated. A controller is configured for energizing an inductor in response to the indicated resistance. An inductor may be energized with an alternating current, a characteristic of which may be selected in response to an indicated electrical resistance. Alternatively, a temperature of the material may be indicated via measuring the electrical resistance thereof and a characteristic of an alternating current for energizing the inductor may be selected in response to the temperature. Energizing the inductor may minimize the difference between a desired and indicated resistance or the difference between a desired and indicated temperature. A method of determining a temperature of at least one region of at least one material to be induction heated includes correlating a measured electrical resistance thereof to an average temperature thereof.

Determining Positions and Desired Applicant Characteristics in Sports Job Ads

ERIC Educational Resources Information Center

Atali, Levent

2015-01-01

The purpose of this study is to determine the diversity of positions occurring in sports job ads and reveal the characteristics requested from applicants for each position. This study examined 103 sports-related job ads obtained from four human resources websites. Using content analysis, job ads were examined in terms of job titles, and the…

Work Ethic and Employment Status: A Study of Jobseekers

ERIC Educational Resources Information Center

Hill, Roger B.; Fouts, Susan

2005-01-01

Although there have been numerous changes within the workplace during the past century, employers continue to search for employees with a strong work ethic. Employers often cite a strong work ethic as the most desired characteristic in a new employee. Work ethic can be described as a set of characteristics and attitudes in which an individual…

Gender Differences in Intrahousehold Schooling Outcomes: The Role of Sibling Characteristics and Birth-Order Effects

ERIC Educational Resources Information Center

Rammohan, Anu; Dancer, Diane

2008-01-01

In this paper we examine the influence of gender, sibling characteristics and birth order on the schooling attainment of school-age Egyptian children. We use multivariate analysis to simultaneously examine three different schooling outcomes of a child having "no schooling", "less than the desired level of schooling", and an…

Desirable Characteristics of a Counseling Agency: Report on a Focus Group Research Study for the Center for Human Services.

ERIC Educational Resources Information Center

Sessions, Joan T.; Yanos, Janet Hagan

This study sought to identify characteristics of counselors and counseling services that are important in the selection of a counseling service. Subjects (N=28) were recruited through a newspaper advertisement and through mall intercepts. The screening criteria were designed to locate potential or previous counseling service consumers whose…

Switched-beam radiometer front-end network analysis

NASA Technical Reports Server (NTRS)

Trew, R. J.; Bilbro, G. L.

1994-01-01

The noise figure performance of various delay-line networks fabricated from microstrip lines with varying number of elements was investigated using a computer simulation. The effects of resistive losses in both the transmission lines and power combiners were considered. In general, it is found that an optimum number of elements exists, depending upon the resistive losses present in the network. Small resistive losses are found to have a significant degrading effect upon the noise figure performance of the array. Extreme stability in switching characteristics is necessary to minimize the nondeterministic noise of the array. For example, it is found that a 6 percent tolerance on the delay-line lengths will produce a 0.2 db uncertainty in the noise figure which translates into a 13.67 K temperature uncertainty generated by the network. If the tolerance can be held to 2 percent, the uncertainty in noise figure and noise temperature will be 0.025 db and 1.67 K, respectively. Three phase shift networks fabricated using a commercially available PIN diode switch were investigated. Loaded-line phase shifters are found to have desirable RF and noise characteristics and are attractive components for use in phased-array networks.

Influences of end-point heating temperature on the quality attributes of chicken meat.

PubMed

Chumngoen, W; Chen, C F; Chen, H Y; Tan, F J

2016-12-01

This study aimed to evaluate the changes in physicochemical, textural and sensory characteristics of broiler (BR) and Taiwan native chicken (TNC) pectoralis muscle heated at temperatures of 50-95°C. With increasing temperature, cooking loss, collagen solubility, shear force value and hardness, of samples increased in both chicken breeds. Rapid decreases in protein solubility were observed when the meat was heated to 50°C and gradually decreased thereafter. Meat from BRs and native chickens performed differently upon heating in certain characteristics. TNC meat had longer cooking time and lower myofibrillar fragmentation index than BR meat did. TNC meat had higher collagen content, shear force values and springiness but lower collagen solubility than BR meat did. BR meat had significantly higher onset and end transition temperatures than TNC meat did. In BR meat, a sensory analysis revealed that moisture release decreased and chicken flavour increased with increasing temperature. Protein solubility, cooking loss and the texture of heated meat were highly correlated. This study scientifically assessed the performances of the two breeds of chickens with different thermal treatments; producers could utilise the information to produce poultry products with more desirable qualities.

Representational and Executive Selection Resources in "Theory of Mind": Evidence from Compromised Belief-Desire Reasoning in Old Age

ERIC Educational Resources Information Center

German, Tim P.; Hehman, Jessica A.

2006-01-01

Effective belief-desire reasoning requires both specialized representational capacities--the capacity to represent the mental states as such--as well as executive selection processes for accurate performance on tasks requiring the prediction and explanation of the actions of social agents. Compromised belief-desire reasoning in a given population…

A Model of Desired Performance in Phylogenetic Tree Construction for Teaching Evolution.

ERIC Educational Resources Information Center

Brewer, Steven D.

This research paper examines phylogenetic tree construction-a form of problem solving in biology-by studying the strategies and heuristics used by experts. One result of the research is the development of a model of desired performance for phylogenetic tree construction. A detailed description of the model and the sample problems which illustrate…

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

1998-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

2000-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

1999-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic base material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, R.A.; McCoig, T.M.; Dooley, J.B.

1998-06-02

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics. 7 figs.

COGNITIVE ABILITY, SOCIAL DESIRABILITY, BODY MASS INDEX, AND SOCIOECONOMIC STATUS AS CORRELATES OF FOURTH-GRADE CHILDREN’S DIETARY-REPORTING ACCURACY

PubMed Central

Smith, Albert F.; Baxter, Suzanne Domel; Hitchcock, David B.; Finney, Christopher J.; Royer, Julie A.; Guinn, Caroline H.

2016-01-01

Objectives To investigate the relationship of reporting accuracy in 24-h dietary recalls to child respondent characteristics—cognitive ability, social desirability, body mass index (BMI) percentile, and socioeconomic status (SES). Subjects/Methods Fourth-grade children (mean age 10.1 years) were observed eating two school meals and interviewed about dietary intake for 24-h that included those meals. (Eight multiple-pass interview protocols operationalized the conditions of an experiment that crossed two retention intervals—short and long—with four prompts [ways of eliciting reports in the first pass].) Academic achievement test scores indexed cognitive ability; social desirability was assessed by questionnaire; height and weight were measured to calculate BMI; nutrition-assistance program eligibility information was obtained to index SES. Reported intake was compared to observed intake to calculate measures of reporting accuracy for school meals at the food-item (omission rate; intrusion rate) and energy (correspondence rate; inflation ratio) levels. Complete data were available for 425 of 480 validation-study participants. Results Controlling for manipulated variables and other measured respondent characteristics, for one or more of the outcome variables, reporting accuracy increased with cognitive ability (omission rate, intrusion rate, correspondence rate, P < .001); decreased with social desirability (correspondence rate, P < .0004); decreased with BMI percentile (correspondence rate, P = .001), and was better by higher than by lower SES children (intrusion rate, P = .001). Some of these effects were moderated by interactions with retention interval and sex. Conclusions Children’s dietary-reporting accuracy is systematically related to such respondent characteristics as cognitive ability, social desirability, BMI percentile, and SES. PMID:27222153

Delayed fertility transition among indigenous women in the Ecuadorian Amazon.

PubMed

Davis, Jason; Bilsborrow, Richard; Gray, Clark

2015-03-01

Communities indigenous to the Amazon are among the few remaining worldwide still practicing near-natural fertility, without the use of modern contraceptives. Given the large proportion of women desiring no more births, information on the challenges women there face in limiting fertility would be useful. Samples of women of reproductive age from five indigenous ethnic groups in the Northern Ecuadorian Amazon were surveyed in 2001 and 2012. Cross-sectional and longitudinal analyses examined married women's desire for another child at both times and modern contraceptive use in 2012, as well as determinants of a change in women's desire to have more children and of the number of children born during the study period. In 2001, 48% of married women desired another child, 2% used a modern contraceptive and 50% had an unmet need for limiting; in 2012, the proportions were 40%, 19% and 47%, respectively. The total fertility rate was 7.9 births per woman in 2001 and 7.0 births per woman in 2012. Characteristics associated with wanting another child in 2001 and 2012 included parity (odds ratios, 0.6 and 0.4, respectively) and experience of a child death (2.0 each); characteristics associated with contraceptive use in 2012 included desire for another child, experience of a child death and presence of a community health worker (0.3-0.5). Number of children born was positively associated, and the square of the term negatively associated, with no longer wanting more children in 2012 among women who wanted more in 2001 (2.1 and 0.9, respectively). Indigenous women in the Northern Ecuadorian Amazon appear to be making the transition to lower fertility. Insufficient access to credible information about the safety and efficacy of modern contraceptives, however, may slow the transition.

Influence of different heat treatment methods of titania film on performance of DSSCs

NASA Astrophysics Data System (ADS)

More, Venumadhav; Mokurala, Krishna; Bhargava, Parag

2018-04-01

Titania mesoporous film is a key component of dye-sensitized solar cells (DSSCs) as it transfers electrons from dye molecule to external circuit through the transparent conducting oxide (TCO). Interparticle connectivity, porosity and cracks in the titania films play an important role in determining the performance of DSSCs. The heating schedule with respect to the repetitive coating to build up titania film thickness impacts the titania film characteristics. In the present study, experiments were designed to carry out heat treatments with expectation of improving connectivity and healing cracks. Repetitive screen printing was carried out with either heat treatment after each print step (multiple sintering) or the heat treatment was carried out just once after the desired thickness had been attained (single-step sintering). Interconnectivity of the titania particles in the sintered titania film was analyzed by impedance spectroscopy and nanoindentation. Titania films sintered by MS showed better performance in terms of higher efficiency for the corresponding DSSCs than those prepared using titania films sintered by SS.

Integrated flight/propulsion control system design based on a centralized approach

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Mattern, Duane L.; Bullard, Randy E.

1989-01-01

An integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statically unstable, fighter aircraft. A centralized compensator based on the Linear Quadratic Gaussian/Loop Transfer Recovery methodology is first obtained to satisfy the feedback loop performance and robustness specificiations. This high-order centralized compensator is then partitioned into airframe and engine sub-controllers based on modal controllability/observability for the compensator modes. The order of the sub-controllers is then reduced using internally-balanced realization techniques and the sub-controllers are simplified by neglecting the insignificant feedbacks. These sub-controllers have the advantage that they can be implemented as separate controllers on the airframe and the engine while still retaining the important performance and stability characteristics of the full-order centralized compensator. Command prefilters are then designed for the closed-loop system with the simplified sub-controllers to obtain the desired system response to airframe and engine command inputs, and the overall system performance evaluation results are presented.

A multifunctional biphasic water splitting catalyst tailored for integration with high-performance semiconductor photoanodes

NASA Astrophysics Data System (ADS)

Yang, Jinhui; Cooper, Jason K.; Toma, Francesca M.; Walczak, Karl A.; Favaro, Marco; Beeman, Jeffrey W.; Hess, Lucas H.; Wang, Cheng; Zhu, Chenhui; Gul, Sheraz; Yano, Junko; Kisielowski, Christian; Schwartzberg, Adam; Sharp, Ian D.

2017-03-01

Artificial photosystems are advanced by the development of conformal catalytic materials that promote desired chemical transformations, while also maintaining stability and minimizing parasitic light absorption for integration on surfaces of semiconductor light absorbers. Here, we demonstrate that multifunctional, nanoscale catalysts that enable high-performance photoelectrochemical energy conversion can be engineered by plasma-enhanced atomic layer deposition. The collective properties of tailored Co3O4/Co(OH)2 thin films simultaneously provide high activity for water splitting, permit efficient interfacial charge transport from semiconductor substrates, and enhance durability of chemically sensitive interfaces. These films comprise compact and continuous nanocrystalline Co3O4 spinel that is impervious to phase transformation and impermeable to ions, thereby providing effective protection of the underlying substrate. Moreover, a secondary phase of structurally disordered and chemically labile Co(OH)2 is introduced to ensure a high concentration of catalytically active sites. Application of this coating to photovoltaic p+n-Si junctions yields best reported performance characteristics for crystalline Si photoanodes.

CONC/11: A computer program for calculating the performance of dish-type solar thermal collectors and power systems

NASA Technical Reports Server (NTRS)

Jaffe, L. D.

1984-01-01

The CONC/11 computer program designed for calculating the performance of dish-type solar thermal collectors and power systems is discussed. This program is intended to aid the system or collector designer in evaluating the performance to be expected with possible design alternatives. From design or test data on the characteristics of the various subsystems, CONC/11 calculates the efficiencies of the collector and the overall power system as functions of the receiver temperature for a specified insolation. If desired, CONC/11 will also determine the receiver aperture and the receiver temperature that will provide the highest efficiencies at a given insolation. The program handles both simple and compound concentrators. The CONC/11 is written in Athena Extended FORTRAN (similar to FORTRAN 77) to operate primarily in an interactive mode on a Sperry 1100/81 computer. It could also be used on many small computers. A user's manual is also provided for this program.

Feasibility Study of a Satellite Solar Power Station

NASA Technical Reports Server (NTRS)

Glaser, P. E.; Maynard, O. E.; Mackovciak, J. J. R.; Ralph, E. I.

1974-01-01

A feasibility study of a satellite solar power station (SSPS) was conducted to: (1) explore how an SSPS could be flown and controlled in orbit; (2) determine the techniques needed to avoid radio frequency interference (RFI); and (3) determine the key environmental, technological, and economic issues involved. Structural and dynamic analyses of the SSPS structure were performed, and deflections and internal member loads were determined. Desirable material characteristics were assessed and technology developments identified. Flight control performance of the SSPS baseline design was evaluated and parametric sizing studies were performed. The study of RFI avoidance techniques covered (1) optimization of the microwave transmission system; (2) device design and expected RFI; and (3) SSPS RFI effects. The identification of key issues involved (1) microwave generation, transmissions, and rectification and solar energy conversion; (2) environmental-ecological impact and biological effects; and (3) economic issues, i.e., costs and benefits associated with the SSPS. The feasibility of the SSPS based on the parameters of the study was established.

SiGe epitaxial memory for neuromorphic computing with reproducible high performance based on engineered dislocations

NASA Astrophysics Data System (ADS)

Choi, Shinhyun; Tan, Scott H.; Li, Zefan; Kim, Yunjo; Choi, Chanyeol; Chen, Pai-Yu; Yeon, Hanwool; Yu, Shimeng; Kim, Jeehwan

2018-01-01

Although several types of architecture combining memory cells and transistors have been used to demonstrate artificial synaptic arrays, they usually present limited scalability and high power consumption. Transistor-free analog switching devices may overcome these limitations, yet the typical switching process they rely on—formation of filaments in an amorphous medium—is not easily controlled and hence hampers the spatial and temporal reproducibility of the performance. Here, we demonstrate analog resistive switching devices that possess desired characteristics for neuromorphic computing networks with minimal performance variations using a single-crystalline SiGe layer epitaxially grown on Si as a switching medium. Such epitaxial random access memories utilize threading dislocations in SiGe to confine metal filaments in a defined, one-dimensional channel. This confinement results in drastically enhanced switching uniformity and long retention/high endurance with a high analog on/off ratio. Simulations using the MNIST handwritten recognition data set prove that epitaxial random access memories can operate with an online learning accuracy of 95.1%.

Effect of different drying techniques on flowability characteristics and chemical properties of natural carbohydrate-protein Gum from durian fruit seed

PubMed Central

2013-01-01

Background A natural carbohydrate biopolymer was extracted from the agricultural biomass waste (durian seed). Subsequently, the crude biopolymer was purified by using the saturated barium hydroxide to minimize the impurities. Finally, the effect of different drying techniques on the flow characteristics and functional properties of the purified biopolymer was investigated. The present study elucidated the main functional characteristics such as flow characteristics, water- and oil-holding capacity, solubility, and foaming capacity. Results In most cases except for oven drying, the bulk density decreased, thus increasing the porosity. This might be attributed to the increase in the inter-particle voids of smaller sized particles with larger contact surface areas per unit volume. The current study revealed that oven-dried gum and freeze-dried gum had the highest and lowest compressibility index, thus indicating the weakest and strongest flowability among all samples. In the present work, the freeze-dried gum showed the lowest angle of repose, bulk, tapped and true density. This indicates the highest porosity degree of freeze dried gum among dried seed gums. It also exhibited the highest solubility, and foaming capacity thus providing the most desirable functional properties and flow characteristics among all drying techniques. Conclusion The present study revealed that freeze drying among all drying techniques provided the most desirable functional properties and flow characteristics for durian seed gum. PMID:23289739

An innovative approach to achieve re-centering and ductility of cement mortar beams through randomly distributed pseudo-elastic shape memory alloy fibers

NASA Astrophysics Data System (ADS)

Shajil, N.; Srinivasan, S. M.; Santhanam, M.

2012-04-01

Fibers can play a major role in post cracking behavior of concrete members, because of their ability to bridge cracks and distribute the stress across the crack. Addition of steel fibers in mortar and concrete can improve toughness of the structural member and impart significant energy dissipation through slow pull out. However, steel fibers undergo plastic deformation at low strain levels, and cannot regain their shape upon unloading. This is a major disadvantage in strong cyclic loading conditions, such as those caused by earthquakes, where self-centering ability of the fibers is a desired characteristic in addition to ductility of the reinforced cement concrete. Fibers made from an alternative material such as shape memory alloy (SMA) could offer a scope for re-centering, thus improving performance especially after a severe loading has occurred. In this study, the load-deformation characteristics of SMA fiber reinforced cement mortar beams under cyclic loading conditions were investigated to assess the re-centering performance. This study involved experiments on prismatic members, and related analysis for the assessment and prediction of re-centering. The performances of NiTi fiber reinforced mortars are compared with mortars with same volume fraction of steel fibers. Since re-entrant corners and beam columns joints are prone to failure during a strong ground motion, a study was conducted to determine the behavior of these reinforced with NiTi fiber. Comparison is made with the results of steel fiber reinforced cases. NiTi fibers showed significantly improved re-centering and energy dissipation characteristics compared to the steel fibers.

Real-Time Minimization of Tracking Error for Aircraft Systems

NASA Technical Reports Server (NTRS)

Garud, Sumedha; Kaneshige, John T.; Krishnakumar, Kalmanje S.; Kulkarni, Nilesh V.; Burken, John

2013-01-01

This technology presents a novel, stable, discrete-time adaptive law for flight control in a Direct adaptive control (DAC) framework. Where errors are not present, the original control design has been tuned for optimal performance. Adaptive control works towards achieving nominal performance whenever the design has modeling uncertainties/errors or when the vehicle suffers substantial flight configuration change. The baseline controller uses dynamic inversion with proportional-integral augmentation. On-line adaptation of this control law is achieved by providing a parameterized augmentation signal to a dynamic inversion block. The parameters of this augmentation signal are updated to achieve the nominal desired error dynamics. If the system senses that at least one aircraft component is experiencing an excursion and the return of this component value toward its reference value is not proceeding according to the expected controller characteristics, then the neural network (NN) modeling of aircraft operation may be changed.

Transparent conductive coatings

NASA Technical Reports Server (NTRS)

Ashok, S.

1983-01-01

Thin film transparent conductors are discussed. Materials with electrical conductivity and optical transparency are highly desirable in many optoelectronic applications including photovoltaics. Certain binary oxide semiconductors such as tin oxide (SnO2) and indium oxide (In2O3) offer much better performance tradeoff in optoelectronics as well as better mechanical and chemical stability than thin semitransparent films. These thin-film transparent conductors (TC) are essentially wide-bandgap degenerate semiconductors - invariably n-type - and hence are transparent to sub-bandgap (visible) radiation while affording high electrical conductivity due to the large free electron concentration. The principal performance characteristics of TC's are, of course, electrical conductivity and optical transmission. The TC's have a refractive index of around 2.0 and hence act as very efficient antireflection coatings. For using TC's in surface barrier solar cells, the photovoltaic barrier is of utmost importance and so the work function or electron affinity of the TC is also a very important material parameter. Fabrication processes are discussed.

The thermal response of HMX-TATB charges

NASA Astrophysics Data System (ADS)

Drake, R. C.

2017-01-01

One approach to achieving charge safety and performance requirements is to prepare formulations containing two (or more) explosives. The intention of this approach is that by judicious choice of explosives and binder the formulation will have the desirable features of the constituent materials. HMX and TATB have very different properties. In an attempt to achieve a formulation which has the safety and performance characteristics of TATB and HMX, respectively, a range of formulations were prepared. The thermal response of the formulations were measured in the One-Dimensional Time To Explosion (ODTX) configuration and compared to those of formulations containing only HMX and TATB. The response of the mixed formulations was found to be largely determined by the HMX component with the binder making a small contribution. A formulation with a Kel-F 800 binder had a much higher critical temperature than would have been expected based on the critical temperatures of formulations with HTPB-IPDI as the binder.

Enhancing managerial effectiveness in dietetics.

PubMed

Hoover, L W

1983-01-01

Environmental pressures from such sources as economic conditions, the government, third-party payers, and inter-institutional competition create managerial challenges. Although cost-containment has received considerable attention, long-term cost-effectiveness is probably the significant issue. Dietitians must become more cost-conscious and effective in resource management to attain desired performance outcomes. Some of the skills and characteristics essential to managerial effectiveness are a marketing orientation, systems design skill, quantitative operations management techniques, financial expertise, and leadership. These abilities facilitate decision-making and achievement of long-term cost-effectiveness. Curriculum enhancement and continuing education are two strategies for improving managerial competency in the dietetics profession. In dietetics education, study of management topics should be enhanced to provide more advanced coverage of management theories and quantitative models so that managerial performance can be at a higher level of sophistication and competency. To assure the viability of the dietetics profession, the emphasis on management must be more comprehensive and rigorous.

Psychological Issues in Online Adaptive Task Allocation

NASA Technical Reports Server (NTRS)

Morris, N. M.; Rouse, W. B.; Ward, S. L.; Frey, P. R.

1984-01-01

Adaptive aiding is an idea that offers potential for improvement over many current approaches to aiding in human-computer systems. The expected return of tailoring the system to fit the user could be in the form of improved system performance and/or increased user satisfaction. Issues such as the manner in which information is shared between human and computer, the appropriate division of labor between them, and the level of autonomy of the aid are explored. A simulated visual search task was developed. Subjects are required to identify targets in a moving display while performing a compensatory sub-critical tracking task. By manipulating characteristics of the situation such as imposed task-related workload and effort required to communicate with the computer, it is possible to create conditions in which interaction with the computer would be more or less desirable. The results of preliminary research using this experimental scenario are presented, and future directions for this research effort are discussed.

"Genetically Engineered" Nanoelectronics

NASA Technical Reports Server (NTRS)

Klimeck, Gerhard; Salazar-Lazaro, Carlos H.; Stoica, Adrian; Cwik, Thomas

2000-01-01

The quantum mechanical functionality of nanoelectronic devices such as resonant tunneling diodes (RTDs), quantum well infrared-photodetectors (QWIPs), quantum well lasers, and heterostructure field effect transistors (HFETs) is enabled by material variations on an atomic scale. The design and optimization of such devices requires a fundamental understanding of electron transport in such dimensions. The Nanoelectronic Modeling Tool (NEMO) is a general-purpose quantum device design and analysis tool based on a fundamental non-equilibrium electron transport theory. NEW was combined with a parallelized genetic algorithm package (PGAPACK) to evolve structural and material parameters to match a desired set of experimental data. A numerical experiment that evolves structural variations such as layer widths and doping concentrations is performed to analyze an experimental current voltage characteristic. The genetic algorithm is found to drive the NEMO simulation parameters close to the experimentally prescribed layer thicknesses and doping profiles. With such a quantitative agreement between theory and experiment design synthesis can be performed.

Lane changing trajectory planning and tracking control for intelligent vehicle on curved road.

PubMed

Wang, Lukun; Zhao, Xiaoying; Su, Hao; Tang, Gongyou

2016-01-01

This paper explores lane changing trajectory planning and tracking control for intelligent vehicle on curved road. A novel arcs trajectory is planned for the desired lane changing trajectory. A kinematic controller and a dynamics controller are designed to implement the trajectory tracking control. Firstly, the kinematic model and dynamics model of intelligent vehicle with non-holonomic constraint are established. Secondly, two constraints of lane changing on curved road in practice (LCCP) are proposed. Thirdly, two arcs with same curvature are constructed for the desired lane changing trajectory. According to the geometrical characteristics of arcs trajectory, equations of desired state can be calculated. Finally, the backstepping method is employed to design a kinematic trajectory tracking controller. Then the sliding-mode dynamics controller is designed to ensure that the motion of the intelligent vehicle can follow the desired velocity generated by kinematic controller. The stability of control system is proved by Lyapunov theory. Computer simulation demonstrates that the desired arcs trajectory and state curves with B-spline optimization can meet the requirements of LCCP constraints and the proposed control schemes can make tracking errors to converge uniformly.

Normativity and Desirability in Observational Assessments of Family Interaction.

PubMed

Deal, James E

2018-06-11

Issues of normativity (responding in a typical or average fashion) and desirability (the tendency for raters to endorse positive characteristics rather than neutral or more negative ones) are common in areas of the social sciences that frequently utilize profile correlations to measure dyadic similarity. They have implications for family scholars as well. In the present study, a pre-existing data set was used to make an initial, though limited, investigation into potential confounds of normativity and desirability for macrolevel observational assessments of family interaction. An empirical example is presented using q-sort ratings of family interaction, with variance in observational assessments decomposed into component parts. High levels of both normativity and desirability were found, indicating possible problems in terms of both reliability and validity of assessment. While the results provide an interesting beginning, they are limited due to the use of a q-sort methodology as well as an instrument with limited background and use. These limitations are discussed, as well as alternative interpretations for normativity and desirability and implications for future research. © 2018 Family Process Institute.

Understanding InP Nanowire Array Solar Cell Performance by Nanoprobe-Enabled Single Nanowire Measurements.

PubMed

Otnes, Gaute; Barrigón, Enrique; Sundvall, Christian; Svensson, K Erik; Heurlin, Magnus; Siefer, Gerald; Samuelson, Lars; Åberg, Ingvar; Borgström, Magnus T

2018-05-09

III-V solar cells in the nanowire geometry might hold significant synthesis-cost and device-design advantages as compared to thin films and have shown impressive performance improvements in recent years. To continue this development there is a need for characterization techniques giving quick and reliable feedback for growth development. Further, characterization techniques which can improve understanding of the link between nanowire growth conditions, subsequent processing, and solar cell performance are desired. Here, we present the use of a nanoprobe system inside a scanning electron microscope to efficiently contact single nanowires and characterize them in terms of key parameters for solar cell performance. Specifically, we study single as-grown InP nanowires and use electron beam induced current characterization to understand the charge carrier collection properties, and dark current-voltage characteristics to understand the diode recombination characteristics. By correlating the single nanowire measurements to performance of fully processed nanowire array solar cells, we identify how the performance limiting parameters are related to growth and/or processing conditions. We use this understanding to achieve a more than 7-fold improvement in efficiency of our InP nanowire solar cells, grown from a different seed particle pattern than previously reported from our group. The best cell shows a certified efficiency of 15.0%; the highest reported value for a bottom-up synthesized InP nanowire solar cell. We believe the presented approach have significant potential to speed-up the development of nanowire solar cells, as well as other nanowire-based electronic/optoelectronic devices.

Differential dietary habits among 570 young underweight Japanese women with and without a desire for thinness: a comparison with normal weight counterparts.

PubMed

Mori, Nagisa; Asakura, Keiko; Sasaki, Satoshi

2016-01-01

The strong social pressure for thinness in Japanese society has produced a dramatic increase in underweight (body mass index: <18.5 kg/m2) among young women. Being underweight is associated with several negative health outcomes, including nutritional deficiency, osteoporosis, and unfavourable pregnancy outcomes. However, evidence which would help deal with this problem from a public health perspective is scarce. Here, we aimed to identify the dietary characteristics of underweight female university students, particularly those with a desire for thinness. Data on dietary habits and other lifestyle variables, including the desire for thinness, were obtained through a self-administered questionnaire survey conducted at 54 academic institutions in Japan, from which we selected 3634 female students for analysis. The subjects were divided into three groups of normal weight (84.3%), and underweight with (6.4%) or without (9.3%) a desire for thinness. After adjusting for potential confounders, the underweight subjects with a desire for thinness consumed less cereal and rice, whereas those without a desire for thinness consumed more cereal and rice than the normal weight subjects. In addition, those without a desire for thinness consumed less confectionaries, including candies and ice cream, and less fats and oils than the normal weight subjects. These results suggest that dietary habits differ between underweight women with and without a desire for thinness. Although both groups require nutritional education to maintain appropriate body weight, underweight women with a desire for thinness require particular attention to improve recognition of their constitution and dietary habits.

Visual Approach and Design: The Appropriate Characteristics of Instructional Photos as a Tool to Support Elementary Setting in Kuwait

ERIC Educational Resources Information Center

Buhamad, Ali

2016-01-01

This study provided a guide for appropriate characteristics of Instructional Photo to be used by teachers, trainers, coaches, instructors, and anyone else who desires to deliver knowledge and present content with visual meaning to elementary students in the state of Kuwait as a teaching style that supports teachers, facilitates clarification, and…

Primary School Pupils' Views of Characteristics of Good Primary School Teachers: An Exploratory, Open Approach for Investigating Pupils' Perceptions

ERIC Educational Resources Information Center

Bakx, Anouke; Koopman, Maaike; de Kruijf, Judith; den Brok, Perry

2015-01-01

This article reports on results of a study on pupils' perceptions on teacher quality in primary education. Pupils' perceptions of desired characteristics of good teachers in primary education were compared to results of research into teacher quality from different perspectives: (1) perception studies of ideal teaching-and-learning environments;…

Employee Characteristics and Skills Valued by Northern Virginia Employers. Business Needs Assessment Study No. 1. Research Report.

ERIC Educational Resources Information Center

Northern Virginia Community Coll., Annandale. Office of Institutional Research.

This paper reports findings of a regional survey of North Virginia businesses. The Office of Institutional Research (OIR) at Northern Virginia Community College (NVCC) conducted the research in an effort to assess the educational and training needs of area businesses. Employers ranked employee desirable characteristics and skills on a scale of 0…

"Smart" Electromechanical Shock Absorber

NASA Technical Reports Server (NTRS)

Stokes, Lebarian; Glenn, Dean C.; Carroll, Monty B.

1989-01-01

Shock-absorbing apparatus includes electromechanical actuator and digital feedback control circuitry rather than springs and hydraulic damping as in conventional shock absorbers. Device not subject to leakage and requires little or no maintenance. Attenuator parameters adjusted in response to sensory feedback and predictive algorithms to obtain desired damping characteristic. Device programmed to decelerate slowly approaching vehicle or other large object according to prescribed damping characteristic.

Can "Any" Teacher Teach Sexuality and HIV/AIDS? Perspectives of South African Life Orientation Teachers

ERIC Educational Resources Information Center

Helleve, Arnfinn; Flisher, Alan J.; Onya, Hans; Mukoma, Wanjiru; Klepp, Knut-Inge

2011-01-01

In this paper we explore the perceived desirable characteristics of South African Life Orientation teachers for teaching sexuality and HIV/AIDS. We also investigate the extent to which these characteristics can be understood as parts of a role script for teaching HIV/AIDS and sexuality. Data were collected from teachers who taught Grade Eight and…

Service patrol handbook.

DOT National Transportation Integrated Search

2008-11-01

This Handbook provides an overview of the Full-Function Service Patrol (FFSP) and describes desired program characteristics from the viewpoint of an agency that is responsible for funding, managing, and operating the services. Presented guidelines an...

The Role of Proximity Effects in Transition-Edge Sensor Design and Performance

NASA Technical Reports Server (NTRS)

Smith, Stephen J.

2012-01-01

Transition-edge sensor (TES) microcalorimeters and bolometers are under development by numerous groups worldwide for a variety of applications involving the measurement of particle and photon radiation. Recent experimental and theoretical progress has led to the realization that the fundamental physics of some TES systems involves the longitudinal proximity effect between the electrical bias contacts and the TES. As such, these devices are described as SS'S (or SN'S) weak-links exhibiting Fraunhofer-like magnetic field dependence, and exponential temperature dependence, of the critical current. These discoveries, for the first time, provide a realistic theoretical framework for predicting the resistive transition as a function of temperature, current and magnetic field. In this contribution, we review the latest theoretical and experimental results and investigate how proximity effects play an important role in determining the resistive transition characteristics, which ultimately determines the dynamic range and energy resolution of TES detectors. We investigate how these effects could be utilized in device design to engineer desired transition characteristics for a given application.

A Manual Control Test for the Detection and Deterrence of Impaired Drivers

NASA Technical Reports Server (NTRS)

Stein, A. C.; Allen, R. W.; Jex, H. R.

1984-01-01

A brief manual control test and a decision strategy were developed, laboratory tested, and field validated which provide a means for detecting human operator impairment from alcohol or other drugs. The test requires the operator to stabilize progressively unstable controlled element dynamics. Control theory and experimental data verify that the human operator's control ability on this task is constrained by basic cybernetic characteristics, and that task performance is reliably affected by impairment effects on these characteristics. Assessment of human operator control ability is determined by a statistically based decision strategy. The operator is allowed several chances to exceed a preset pass criterion. Procedures are described for setting the pass criterion based on individual ability and a desired unimpaired failure rate. These procedures were field tested with apparatus installed in automobiles that were designed to discourage drunk drivers from operating their vehicles. This test program demonstrated that the control task and detection strategy could be applied in a practical setting to screen human operators for impairment in their basic cybernetic skills.

Investigation of Flash Fill{reg_sign} as a thermal backfill material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayers, P.H.; Charlton, C.B.; Frishette, C.W.

1995-09-01

Flash Fill{reg_sign} was created as a fast-setting, flowable backfill material made entirely from coal combustion by-products and water. Its quick-setting, self-leveling, self-compacting characteristics makes trench road repairs faster, easier, and more economical. Other uses include building foundations, fill around pipes, gas lines, and manholes, and replacement of weak subgrade beneath rooters. Flash Fill can be hand-excavated without the use of power assisted tools or machinery. To enhance thermal resistivity, the original Flash Fill mix was modified to include concrete sand. This resulted in a new Flash Fill, designated FSAND, with all of the aforementioned desirable characteristics of Flash Fill andmore » a thermal resistivity of approximately 50{degree} C-cm/watt. Thermal resistivity tests using conventional laboratory thermal probes, high-current thermal tests, and moisture migration tests have been performed to determine the properties of FSAND. As a result of these tests, FSAND has been approved for use as power cable thermal backfill on all AEP System distribution projects.« less

Characterization of Solidifiers used for Oil Spill Remediation ...

EPA Pesticide Factsheets

The physical characteristics and chemical composition of oil spill solidifiers were studied, and correlation of these properties with product effectiveness enabled determination of characteristics that are desirable in a good solidifier. The analyses revealed that the commercial products were primarily comprised of organic polymers and a few trace elements. A natural sorbent, which was composed entirely of plant based matter, was also evaluated, and it had the highest oil removal capacity, but it did not produce a solid mat-like final product. Generally, solidifiers with a carbonate group, pore size greater than 5 µm, and bulk densities lower than 0.3 g cm-3 were found to have better efficiency and produced a cohesive rubbery final product that facilitated removal compared to sorbents. The importance of bulk density and pore size in the performance of the solidifier suggest that the primary mechanism of action was likely physical sorption. In this study, we focused on characterizing the 12 solidifiers by using different analytical techniques.

High sensitivity pressure transducer based on the phase characteristics of GMI magnetic sensors

NASA Astrophysics Data System (ADS)

Benavides, L. S.; Costa Silva, E.; Costa Monteiro, E.; Hall Barbosa, C. R.

2018-03-01

This paper presents a new configuration for a GMI pressure transducer based on the reading of the phase characteristics of GMI sensor, intended for biomedical applications. The development process of this new class of magnetic field transducers is discussed, beginning with the definition of the ideal conditioning of the GMI sensor elements (dc level and frequency of the excitation current and sample length) and continuing with computational simulations of the full electronic circuit performed using the experimental data obtained from measured GMI curves, and have shown that the improvement in the sensitivity of GMI magnetometers is larger when phase-based transducers are used instead of magnitude-based transducers. Parameters of interest of the developed prototype are thoroughly analyzed, such as: sensitivity, linearity and frequency response. Also, the spectral noise density of the developed pressure transducer is evaluated and its resolution in the passband is estimated. A low-cost GMI pressure transducer was developed, presenting high resolution, high sensitivity and a frequency bandwidth compatible to the desired biomedical applications.

Experiments on Ion Beam Deflection Using Ion Optics with Slit Apertures

NASA Astrophysics Data System (ADS)

Okawa, Yasushi; Hayakawa, Yukio; Kitamura, Shoji

2004-03-01

An experimental investigation on ion beam deflection by grid translation was performed. The ion beam deflection in ion optics is a desired technology for ion thrusters because thrust vector control utilizing this technique can eliminate the need for conventional gimbaling devices and thus reduce propulsion system mass. A grid translation mechanism consisting of a piezoelectric motor, a ceramic lever, and carbon-based grids with slit apertures was fabricated and high repeatability in beam deflection characteristics was obtained using this mechanism. Results showed that the beam deflection angle was proportional to the grid translation distance and independent of slit width and grid voltage. A numerical simulation successfully reproduced the beam deflection characteristics in a qualitative and quantitative sense. A maximum beam deflection angle of approximately plus or minus 6 degrees, which was comparable to that of the ordinary gimbaling devices used in space, was obtained without a severe drain current. Therefore, the beam deflection by grid translation is promising as a thrust vectoring method in ion thrusters.

What Kind of Faculty Are Motivated to Perform Research by the Desire for Promotion?

ERIC Educational Resources Information Center

Tien, Flora F.

2008-01-01

A policy of adding a new rank to the faculty career ladder was implemented in Taiwan in 1994. It was believed that structural changes of the incentive system would change faculty research behavior. This paper explores the question: Who are motivated to perform research by the desire for promotion? A mail survey investigating Taiwanese faculty…

Managing for desired experiences and site preferences: the case of fee-fishing anglers.

PubMed

Schuett, Michael A; Pierskalla, Chad D

2007-02-01

Fee-fishing involves paying a fee for the privilege of fishing a body of water where fish populations are enhanced by stocking fish. Past literature on this activity has focused more on the operation of the enterprise and management of the fish than the people and site characteristics. The objectives of the study were to profile anglers and describe their site/management preferences. This study utilized an on-site interview and mail-back questionnaire at fee-fishing establishments in West Virginia (n = 212). Factor analysis of desired recreation experiences yielded five factors: Experience nature & adventure, Stress release & relaxation, Trophy fishing, Escape, and Family time. Cluster analysis showed that these anglers can be segmented into two distinct clusters, differing by sociodemographic characteristics, fishing behavior, and site/management preferences. The findings from this study provide baseline data to aid public resource managers and fee-fishing business owners in determining how to provide satisfying outdoor experiences and deliver desired services on-site. Future research will be needed from additional fee-fishing sites to obtain more detail about this outdoor recreation cohort and be able to generalize to a larger population of participants.

Managing for Desired Experiences and Site Preferences: The Case of Fee-Fishing Anglers

NASA Astrophysics Data System (ADS)

Schuett, Michael A.; Pierskalla, Chad D.

2007-02-01

Fee-fishing involves paying a fee for the privilege of fishing a body of water where fish populations are enhanced by stocking fish. Past literature on this activity has focused more on the operation of the enterprise and management of the fish than the people and site characteristics. The objectives of the study were to profile anglers and describe their site/management preferences. This study utilized an on-site interview and mail-back questionnaire at fee-fishing establishments in West Virginia ( n = 212). Factor analysis of desired recreation experiences yielded five factors: Experience nature & adventure, Stress release & relaxation, Trophy fishing, Escape, and Family time. Cluster analysis showed that these anglers can be segmented into two distinct clusters, differing by sociodemographic characteristics, fishing behavior, and site/management preferences. The findings from this study provide baseline data to aid public resource managers and fee-fishing business owners in determining how to provide satisfying outdoor experiences and deliver desired services on-site. Future research will be needed from additional fee-fishing sites to obtain more detail about this outdoor recreation cohort and be able to generalize to a larger population of participants.

Application of Lorenz curve to interpret concentration of contraception and fertility in a population.

PubMed

Ghanma, M A; Rider, R V; Sirageldin, I

1984-01-01

The Lorenz Curve, originally developed to measure the concentration of wealth in a population, was used to describe the distribution of contraceptive practice in Jordan. Data from the 1976 Jordan Fertility Study, carried out as part of the World Fertility Survey program, was used in the analysis. The application of the Automatic Interaction Detector program to the survey's sample population of 3611 women of reproductive age divided the sample into 6 mutually exclusive groups on the basis of residence, education, and whether desired family size was attained or not attained. These 3 characteristics accounted for a major portion of the variation in contraceptive practice. These subgroups, in ascending order by the proportion practicing contraception, were: 1) rural women with unattained desired family size; 2) urban, illiterate women with unattained desired family size; 3) rural women with attained desired family size; 4) urban, literate women with unattained desired family size; 5) urban, illiterate women with attained desired family size; and 6) urban, literate women with attained desired family size. The cumulative proportion of the sample in each ordered subdivision was plotted on the X axis of a graph, and the cumulative proportion of those practicing contraception was plotted on the Y axis of the graph. A line connecting the intersection of the points on the X and Y axis was then drawn. The resultant line was a concave ascending line. If contraceptive practice was evenly distributed in the population, the line would be a straight diagonal line. The plotted curved line indicated that contraceptive practice was unevenly distributed in the population. 2 indexes for measuring the area between the diagonal and the line resulting from plotting the observed distribution for each subgroup was used to assess the degree of concentration of contraceptive practice in the population. The indexes also indicated that contraceptive practice was unequally distributed. When separate curves were plotted for the subgroups with attained desired family size and the subgroups without attained desired family size, it was apparent that the distribution of contraceptive practice was more uniform among those with attained desired family size than among the other 3 subgroups. A curve for the distribution of births was then plotted on the same graph. This curve was not a true application of the Lorenz Curve since it was based on the order of the subdivisions by birth rates. The resultant line approached the straight diagonal line and indicated that the distribution of births was fairly evenly distributed in the population. The uneven distribution of contraceptive practice and the uniform distribution of births suggests that contraceptive practice in this population is ineffective. This may be a characteristic of populations in the early stages of fertility control.

Hybrid aerogel-derived Sn-Ni alloy immobilized within porous carbon/graphene dual matrices for high-performance lithium storage.

PubMed

Zhang, Hao; Zhang, Mengru; Zhang, Meiling; Zhang, Lin; Zhang, Anping; Zhou, Yiming; Wu, Ping; Tang, Yawen

2017-09-01

Nanoporous networks of tin-based alloys immobilized within carbon matrices possess unique structural and compositional superiorities toward lithium-storage, and are expected to manifest improved strain-accommodation and charge-transport capabilities and thus desirable anodic performance for advanced lithium-ion batteries (LIBs). Herein, a facile and scalable hybrid aerogel-derived thermal-autoreduction route has been developed for the construction of nanoporous network of SnNi alloy immobilized within carbon/graphene dual matrices (SnNi@C/G network). When applied as an anode material for LIBs, the SnNi@C/G network manifests desirable lithium-storage performances in terms of specific capacities, cycle life, and rate capability. The facile aerogel-derived route and desirable Li-storage performance of the SnNi@C/G network facilitate its practical application as a high-capacity, long-life, and high-rate anode material for advanced LIBs. Copyright © 2017 Elsevier Inc. All rights reserved.

Next generation biofuel engineering in prokaryotes

PubMed Central

Gronenberg, Luisa S.; Marcheschi, Ryan J.; Liao, James C.

2014-01-01

Next-generation biofuels must be compatible with current transportation infrastructure and be derived from environmentally sustainable resources that do not compete with food crops. Many bacterial species have unique properties advantageous to the production of such next-generation fuels. However, no single species possesses all characteristics necessary to make high quantities of fuels from plant waste or CO2. Species containing a subset of the desired characteristics are used as starting points for engineering organisms with all desired attributes. Metabolic engineering of model organisms has yielded high titer production of advanced fuels, including alcohols, isoprenoids and fatty acid derivatives. Technical developments now allow engineering of native fuel producers, as well as lignocellulolytic and autotrophic bacteria, for the production of biofuels. Continued research on multiple fronts is required to engineer organisms for truly sustainable and economical biofuel production. PMID:23623045

Systems and methods of varying charged particle beam spot size

DOEpatents

Chen, Yu-Jiuan

2014-09-02

Methods and devices enable shaping of a charged particle beam. A modified dielectric wall accelerator includes a high gradient lens section and a main section. The high gradient lens section can be dynamically adjusted to establish the desired electric fields to minimize undesirable transverse defocusing fields at the entrance to the dielectric wall accelerator. Once a baseline setting with desirable output beam characteristic is established, the output beam can be dynamically modified to vary the output beam characteristics. The output beam can be modified by slightly adjusting the electric fields established across different sections of the modified dielectric wall accelerator. Additional control over the shape of the output beam can be excreted by introducing intentional timing de-synchronization offsets and producing an injected beam that is not fully matched to the entrance of the modified dielectric accelerator.

Systematic design methodology for robust genetic transistors based on I/O specifications via promoter-RBS libraries.

PubMed

Lee, Yi-Ying; Hsu, Chih-Yuan; Lin, Ling-Jiun; Chang, Chih-Chun; Cheng, Hsiao-Chun; Yeh, Tsung-Hsien; Hu, Rei-Hsing; Lin, Che; Xie, Zhen; Chen, Bor-Sen

2013-10-27

Synthetic genetic transistors are vital for signal amplification and switching in genetic circuits. However, it is still problematic to efficiently select the adequate promoters, Ribosome Binding Sides (RBSs) and inducer concentrations to construct a genetic transistor with the desired linear amplification or switching in the Input/Output (I/O) characteristics for practical applications. Three kinds of promoter-RBS libraries, i.e., a constitutive promoter-RBS library, a repressor-regulated promoter-RBS library and an activator-regulated promoter-RBS library, are constructed for systematic genetic circuit design using the identified kinetic strengths of their promoter-RBS components.According to the dynamic model of genetic transistors, a design methodology for genetic transistors via a Genetic Algorithm (GA)-based searching algorithm is developed to search for a set of promoter-RBS components and adequate concentrations of inducers to achieve the prescribed I/O characteristics of a genetic transistor. Furthermore, according to design specifications for different types of genetic transistors, a look-up table is built for genetic transistor design, from which we could easily select an adequate set of promoter-RBS components and adequate concentrations of external inducers for a specific genetic transistor. This systematic design method will reduce the time spent using trial-and-error methods in the experimental procedure for a genetic transistor with a desired I/O characteristic. We demonstrate the applicability of our design methodology to genetic transistors that have desirable linear amplification or switching by employing promoter-RBS library searching.

Systematic design methodology for robust genetic transistors based on I/O specifications via promoter-RBS libraries

PubMed Central

2013-01-01

Background Synthetic genetic transistors are vital for signal amplification and switching in genetic circuits. However, it is still problematic to efficiently select the adequate promoters, Ribosome Binding Sides (RBSs) and inducer concentrations to construct a genetic transistor with the desired linear amplification or switching in the Input/Output (I/O) characteristics for practical applications. Results Three kinds of promoter-RBS libraries, i.e., a constitutive promoter-RBS library, a repressor-regulated promoter-RBS library and an activator-regulated promoter-RBS library, are constructed for systematic genetic circuit design using the identified kinetic strengths of their promoter-RBS components. According to the dynamic model of genetic transistors, a design methodology for genetic transistors via a Genetic Algorithm (GA)-based searching algorithm is developed to search for a set of promoter-RBS components and adequate concentrations of inducers to achieve the prescribed I/O characteristics of a genetic transistor. Furthermore, according to design specifications for different types of genetic transistors, a look-up table is built for genetic transistor design, from which we could easily select an adequate set of promoter-RBS components and adequate concentrations of external inducers for a specific genetic transistor. Conclusion This systematic design method will reduce the time spent using trial-and-error methods in the experimental procedure for a genetic transistor with a desired I/O characteristic. We demonstrate the applicability of our design methodology to genetic transistors that have desirable linear amplification or switching by employing promoter-RBS library searching. PMID:24160305

Control of arc length during gas metal arc welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madigan, R.B.; Quinn, T.P.

1994-12-31

An arc-length control system has been developed for gas metal arc welding (GMAW) under spray transfer welding conditions. The ability to monitor and control arc length during arc welding allows consistent weld characteristics to be maintained and therefore improves weld quality. Arc length control has only been implemented for gas tungsten arc welding (GTAW), where an automatic voltage control (AVC) unit adjusts torch-to-work distance. The system developed here compliments the voltage- and current-sensing techniques commonly used for control of GMAW. The system consists of an arc light intensity sensor (photodiode), a Hall-effect current sensor, a personal computer and software implementingmore » a data interpretation and control algorithms. Arc length was measured using both arc light and arc current signals. Welding current was adjusted to maintain constant arc length. A proportional-integral-derivative (PID) controller was used. Gains were automatically selected based on the desired welding conditions. In performance evaluation welds, arc length varied from 2.5 to 6.5 mm while welding up a sloped workpiece (ramp in CTWD) without the control. Arc length was maintained within 1 mm of the desired (5 mm ) with the control.« less

Navigating the poverty of heroin addiction treatment and recovery opportunity in Kenya: access work, self-care and rationed expectations.

PubMed

Rhodes, Tim; Ndimbii, James; Guise, Andy; Cullen, Lucy; Ayon, Sylvia

2015-01-01

Drawing on the analyses of qualitative interview accounts of people who inject heroin in Kenya, we describe the narration of addiction treatment access and recovery desire in conditions characterised by a 'poverty of drug treatment opportunity'. We observe the performance of addiction recovery narrative in the face of heavy social constraints limiting access to care. Fee-based residential rehabilitation ('rehab') is the only treatment locally available and inaccessible to most. Its recovery potential is doubted, given normative expectations of relapse. Treating drug use is a product of tightly bounded agency. Individuals enact strategies to maximise their slim chances of treatment access ('access work'), develop self-care alternatives when these fail to materialise and ration their care expectations. The use of rehab as a primary means of respite and harm reduction rather than recovery and the individuation of care in the absence of an enabling recovery environment are key characteristics of drug treatment experience. The recent incorporation of 'harm reduction' into policy discourses may trouble the primacy of recovery narrative in addiction treatment and in how treatment desires are voiced. The diversification of drug treatments in combination with social interventions enabling their access are fundamental.

Design and characterization of diclofenac diethylamine transdermal patch using silicone and acrylic adhesives combination.

PubMed

Panchaxari, Dandigi M; Pampana, Sowjanya; Pal, Tapas; Devabhaktuni, Bhavana; Aravapalli, Anil Kumar

2013-01-07

The objective of the study was to develop and characterize Diclofenac Diethylamine (DDEA) transdermal patch using Silicone and acrylic adhesives combination. Modified solvent evaporation method was employed for casting of film over Fluoropolymer coated polyester release liner. Initial studies included solubilization of drug in the polymers using solubilizers. The formulations with combination of adhesives were attempted to combine the desirable features of both the adhesives. The effect of the permeation enhancers on the drug permeation were studied using pig ear skin. All the optimized patches were subjected to adhesion, dissolution and stability studies. A 7-day skin irritancy test on albino rabbits and an in vivo anti-inflammatory study on wistar rats by carrageenan induced paw edema method were also performed. The results indicated the high percent drug permeation (% CDP-23.582) and low solubility nature (1%) of Silicone adhesive and high solubility (20%) and low% CDP (10.72%) of acrylic adhesive. The combination of adhesives showed desirable characteristics for DDEA permeation with adequate % CDP and sufficient solubility. Release profiles were found to be dependent on proportion of polymer and type of permeation enhancer. The anti-inflammatory study revealed the sustaining effect and high percentage inhibition of edema of C4/OLA (99.68%). The acute skin irritancy studies advocated the non-irritant nature of the adhesives used. It was concluded that an ideal of combination of adhesives would serve as the best choice, for fabrication of DDEA patches, for sustained effect of DDEA with better enhancement in permeation characteristics and robustness.

Design and characterization of diclofenac diethylamine transdermal patch using silicone and acrylic adhesives combination

PubMed Central

2013-01-01

Background and purpose of the study The objective of the study was to develop and characterize Diclofenac Diethylamine (DDEA) transdermal patch using Silicone and acrylic adhesives combination. Methods Modified solvent evaporation method was employed for casting of film over Fluoropolymer coated polyester release liner. Initial studies included solubilization of drug in the polymers using solubilizers. The formulations with combination of adhesives were attempted to combine the desirable features of both the adhesives. The effect of the permeation enhancers on the drug permeation were studied using pig ear skin. All the optimized patches were subjected to adhesion, dissolution and stability studies. A 7-day skin irritancy test on albino rabbits and an in vivo anti-inflammatory study on wistar rats by carrageenan induced paw edema method were also performed. Results The results indicated the high percent drug permeation (% CDP-23.582) and low solubility nature (1%) of Silicone adhesive and high solubility (20%) and low% CDP (10.72%) of acrylic adhesive. The combination of adhesives showed desirable characteristics for DDEA permeation with adequate % CDP and sufficient solubility. Release profiles were found to be dependent on proportion of polymer and type of permeation enhancer. The anti-inflammatory study revealed the sustaining effect and high percentage inhibition of edema of C4/OLA (99.68%). The acute skin irritancy studies advocated the non-irritant nature of the adhesives used. Conclusion It was concluded that an ideal of combination of adhesives would serve as the best choice, for fabrication of DDEA patches, for sustained effect of DDEA with better enhancement in permeation characteristics and robustness. PMID:23351568

Screening studies of advanced control concepts for airbreathing engines

NASA Technical Reports Server (NTRS)

Ouzts, Peter J.; Lorenzo, Carl F.; Merrill, Walter C.

1993-01-01

The application of advanced control concepts to airbreathing engines may yield significant improvements in aircraft/engine performance and operability. Accordingly, the NASA Lewis Research Center has conducted screening studies of advanced control concepts for airbreathing engines to determine their potential impact on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed concepts was formulated by NASA and industry. These concepts were evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation, three target aircraft/engine combinations were considered: a military high performance fighter mission, a high speed civil transport mission, and a civil tiltrotor mission. Each of the advanced control concepts considered in the study were defined and described. The concept's potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts were also determined. Finally, the concepts were ranked with respect to the target aircraft/engine missions.

PERFORMANCE TESTS OF SNAP 10A THERMOELECTRIC ELEMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bergdorf, C.G.

1961-08-30

Apparatus for the performanee testing of SNAP 10A thermoelectric elements was designed, constructed, and is now in operation. Elements may be tested for any desired length of tfme up to 1400 deg F and in a vacuum of 1 x 10/ sup -5/ of Hg. The equipment used for these tcsts may also be utilized for measuring Seebeck coefficient and resistance as a function of temperature. Element performance is derived from the data on voltages and temperatures. The performance variables which are reported in graphic form are as follows: loaded output voltage at any desired DELTA T; open circuit outputmore » voltage at any desired DELTA T; power output under optimum load conditions; current produced under matched load conditions; and internal resistance of the element. (auth)« less

On analytic design of loudspeaker arrays with uniform radiation characteristics

PubMed

Aarts; Janssen

2000-01-01

Some notes on analytical derived loudspeaker arrays with uniform radiation characteristics are presented. The array coefficients are derived via analytical means and compared with so-called maximal flat sequences known from telecommunications and information theory. It appears that the newly derived array, i.e., the quadratic phase array, has a higher efficiency than the Bessel array and a flatter response than the Barker array. The method discussed admits generalization to the design of arrays with desired nonuniform radiating characteristics.

High-Temperature Smart Structures for Engine Noise Reduction and Performance Enhancement

NASA Technical Reports Server (NTRS)

Quackenbush, Todd R.; McKillip, Robert M., Jr.

2011-01-01

One of key NASA goals is to develop and integrate noise reduction technology to enable unrestricted air transportation service to all communities. One of the technical priorities of this activity has been to account for and reduce noise via propulsion/airframe interactions, identifying advanced concepts to be integrated with the airframe to mitigate these noise-producing mechanisms. An adaptive geometry chevron using embedded smart structures technology offers the possibility of maximizing engine performance while retaining and possibly enhancing the favorable noise characteristics of current designs. New high-temperature shape memory alloy (HTSMA) materials technology enables the devices to operate in both low-temperature (fan) and high-temperature (core) exhaust flows. Chevron-equipped engines have demonstrated reduced noise in testing and operational use. It is desirable to have the noise benefits of chevrons in takeoff/landing conditions, but have them deployed into a minimum drag position for cruise flight. The central feature of the innovation was building on rapidly maturing HTSMA technology to implement a next-generation aircraft noise mitigation system centered on adaptive chevron flow control surfaces. In general, SMA-actuated devices have the potential to enhance the demonstrated noise reduction effectiveness of chevron systems while eliminating the associated performance penalty. The use of structurally integrated smart devices will minimize the mechanical and subsystem complexity of this implementation. The central innovations of the effort entail the modification of prior chevron designs to include a small cut that relaxes structural stiffness without compromising the desired flow characteristics over the surface; the reorientation of SMA actuation devices to apply forces to deflect the chevron tip, exploiting this relaxed stiffness; and the use of high-temperature SMA (HTSMA) materials to enable operation in the demanding core chevron environment. The overall conclusion of these design studies was that the cut chevron concept is a critical enabling step in bringing the variable geometry core chevron within reach. The presence of the cut may be aerodynamically undesirable in some respects, but it is present only when the chevron is not immersed in the core jet exhaust. When deployed, the gap closes as the chevron tip enters the high-speed, high-temperature core stream. Aeroacoustic testing and flow visualization support the contention that this cut is inconsequential to chevron performance.

Numerical analysis of the performance of rock weirs: Effects of structure configuration on local hydraulics

USGS Publications Warehouse

Holmquist-Johnson, C. L.

2009-01-01

River spanning rock structures are being constructed for water delivery as well as to enable fish passage at barriers and provide or improve the aquatic habitat for endangered fish species. Current design methods are based upon anecdotal information applicable to a narrow range of channel conditions. The complex flow patterns and performance of rock weirs is not well understood. Without accurate understanding of their hydraulics, designers cannot address the failure mechanisms of these structures. Flow characteristics such as jets, near bed velocities, recirculation, eddies, and plunging flow govern scour pool development. These detailed flow patterns can be replicated using a 3D numerical model. Numerical studies inexpensively simulate a large number of cases resulting in an increased range of applicability in order to develop design tools and predictive capability for analysis and design. The analysis and results of the numerical modeling, laboratory modeling, and field data provide a process-based method for understanding how structure geometry affects flow characteristics, scour development, fish passage, water delivery, and overall structure stability. Results of the numerical modeling allow designers to utilize results of the analysis to determine the appropriate geometry for generating desirable flow parameters. The end product of this research will develop tools and guidelines for more robust structure design or retrofits based upon predictable engineering and hydraulic performance criteria. ?? 2009 ASCE.

Fretting wear study of surface modified Ni-Ti shape memory alloy.

PubMed

Tan, L; Crone, W C; Sridharan, K

2002-05-01

A combination of shape memory characteristics, pseudoelasticity, and good damping properties make near-equiatomic nickel-titanium (Ni-Ti) alloy a desirable candidate material for certain biomedical device applications. The alloy has moderately good wear resistance, however, further improvements in this regard would be beneficial from the perspective of reducing wear debris generation, improving biocompatibility, and preventing failure during service. Fretting wear tests of Ni-Ti in both austenitic and martensitic microstructural conditions were performed with the goal of simulating wear which medical devices such as stents may experience during surgical implantation or service. The tests were performed using a stainless steel stylus counter-wearing surface under dry conditions and also with artificial plasma containing 80 g/L albumen protein as lubricant. Additionally, the research explores the feasibility of surface modification by sequential ion implantation with argon and oxygen to enhance the wear characteristics of the Ni-Ti alloy. Each of these implantations was performed to a dose of 3 x 10(17) atom/cm(2) and an energy of 50 kV, using the plasma source ion implantation process. Improvements in wear resistance were observed for the austenitic samples implanted with argon and oxygen. Ion implantation with argon also reduced the surface Ni content with respect to Ti due to differential sputtering rates of the two elements, an effect that points toward improved biocompatibility.

The desire and capability of Australian general practitioners to change their working hours.

PubMed

Norman, Richard; Hall, Jane P

2014-04-21

To explore factors associated with general practitioners' desire to work less and their success in making that change. Waves 3 and 4 (conducted in 2010 and 2011) of a national longitudinal survey of Australian doctors in clinical practice (Medicine in Australia: Balancing Employment and Life). Of the broader group of medical practitioners in the survey, there were 3664 and 3436 GP completers in Waves 3 and 4, respectively. The association between the desire to reduce hours and doctor, job and geographic characteristics; the association between predictors of the capability to reduce hours and these same doctor, job and geographic characteristics. Over 40% of GPs stated a preference to reduce their working hours. Characteristics that predicted this preference were being middle-aged, being female, working ≥ 40 hours per week (all P < 0.01), and being on call (P = 0.03). Factors associated with not wanting to reduce working hours were being in excellent health, being satisfied or very satisfied with work (both P < 0.01), and not being a partner in a practice (P < 0.01 for a number of alternative options [ie, associates, contractors and locums]). Of those who wanted to reduce working hours, 26.8% successfully managed to do so in the subsequent year (where reduction was defined as reducing hours by at least 5 per week). Predictors of successfully reducing hours were being younger, female and working ≥ 40 hours per week (all P < 0.01). A number of factors appear to determine both the desire of GPs to reduce hours and their subsequent success in doing so. Declining working hours have contributed to the perceived shortage in GPs. Therefore, designing policies that address not just the absolute number of medical graduates but also their subsequent level of work may alleviate some of the pressures on the Australian primary health care system.

A Multivariate Quality Loss Function Approach for Optimization of Spinning Processes

NASA Astrophysics Data System (ADS)

Chakraborty, Shankar; Mitra, Ankan

2018-05-01

Recent advancements in textile industry have given rise to several spinning techniques, such as ring spinning, rotor spinning etc., which can be used to produce a wide variety of textile apparels so as to fulfil the end requirements of the customers. To achieve the best out of these processes, they should be utilized at their optimal parametric settings. However, in presence of multiple yarn characteristics which are often conflicting in nature, it becomes a challenging task for the spinning industry personnel to identify the best parametric mix which would simultaneously optimize all the responses. Hence, in this paper, the applicability of a new systematic approach in the form of multivariate quality loss function technique is explored for optimizing multiple quality characteristics of yarns while identifying the ideal settings of two spinning processes. It is observed that this approach performs well against the other multi-objective optimization techniques, such as desirability function, distance function and mean squared error methods. With slight modifications in the upper and lower specification limits of the considered quality characteristics, and constraints of the non-linear optimization problem, it can be successfully applied to other processes in textile industry to determine their optimal parametric settings.

Simplified ZrTiO x -based RRAM cell structure with rectifying characteristics by integrating Ni/n + -Si diode.

PubMed

Lin, Chia-Chun; Wu, Yung-Hsien; Chang, You-Tai; Sun, Cherng-En

2014-01-01

A simplified one-diode one-resistor (1D1R) resistive switching memory cell that uses only four layers of TaN/ZrTiO x /Ni/n(+)-Si was proposed to suppress sneak current where TaN/ZrTiO x /Ni can be regarded as a resistive-switching random access memory (RRAM) device while Ni/n(+)-Si acts as an Schottky diode. This is the first RRAM cell structure that employs metal/semiconductor Schottky diode for current rectifying. The 1D1R cell exhibits bipolar switching behavior with SET/RESET voltage close to 1 V without requiring a forming process. More importantly, the cell shows tight resistance distribution for different states, significantly rectifying characteristics with forward/reverse current ratio higher than 10(3) and a resistance ratio larger than 10(3) between two states. Furthermore, the cell also displays desirable reliability performance in terms of long data retention time of up to 10(4) s and robust endurance of 10(5) cycles. Based on the promising characteristics, the four-layer 1D1R structure holds the great potential for next-generation nonvolatile memory technology.

Relation between Self-Esteem and Socially Desirable Responding and the Role of Socially Desirable Responding in the Relation between Self-Esteem and Performance

ERIC Educational Resources Information Center

Huang, Chiungjung

2013-01-01

This investigation examines the relation between self-esteem and socially desirable responding by integrating previous findings via a meta-analysis. In 55 studies containing 73 independent samples (N?=?11,901), the correlation between self-esteem and Impression Management was weak, that between self-esteem and Self-Deceptive Enhancement was from…

Electrostatic focusing of directly heated linear filament gun using EGUN

NASA Astrophysics Data System (ADS)

Iqbal, Munawar; Lodhi, M. A. K.; Majeed, Zahid; Batani, Dimitri

2011-06-01

This paper presents the optimization of a line source rectangular electron gun using electrostatic focusing. We optimized the gun by shaping the configuration of its electrodes in order to achieve the desired focusing characteristics, namely maximum focusing distance and minimum beam spread. The optimization has been carried out using the software EGUN. We have also simplified the gun design using only one focusing electrode at the same potential as that of the cathode and by avoiding magnetic focusing field, separate focusing electrodes and additional power supply, thus minimizing the cost without any loss in its accuracy and efficient performance. This gun with the optimum configuration was used in actual experiment and the results of the simulation were compared with the experimental measurements.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aytug, Tolga; Simpson, John T.; Lupini, Andrew R.

Inspired by highly non-wetting natural biological surfaces (e.g., lotus leaves and water strider legs), artificial superhydrophobic surfaces that exhibit water droplet contact angles exceeding 150o have previously been constructed by utilizing various synthesis strategies.[ , , ] Such bio-inspired, water-repellent surfaces offer significant potential for numerous uses ranging from marine applications (e.g., anti-biofouling, anti-corrosion), anti-condensation (e.g., anti-icing, anti-fogging), membranes for selective separation (e.g., oil-water, gas-liquid), microfluidic systems, surfaces requiring reduced maintenance and cleaning, to applications involving glasses and optical materials.[ ] In addition to superhydrophobic attributes, for integration into device systems that have extended operational limits and overall improved performance,more » surfaces that also possess multifunctional characteristics are desired, where the functionality should match to the application-specific requirements.« less

Financial reporting practices: a comprehensive evaluation.

PubMed

Godwin, Norman H; Mueller, Jennifer M

2005-01-01

A distinguishing characteristic of high performance organizations is a strong internal control structure-controls that ensure patient care, compliance with regulations, internal efficiencies, and financial reporting. It is controls on financial reporting that are receiving a great deal of attention under a new law, the Sarbanes-Oxley Act of 2002. Public companies are now required by law to document controls over financial reporting, in order to fully address exposures and the effectiveness of current controls. Though many healthcare organizations are not directly affected by the law, regulatory agencies could follow suit and require similar compliance. In fact, several states have introduced bills that require nonprofit organizations to adhere to portions of the act. This article provides a guide for organizations desiring to stay ahead of the curve.

Characterization and simulation of soft gamma-ray mirrors for their use with spent fuel rods at reprocessing facilities

DOE PAGES

Ruz, J.; Descalle, M. A.; Alameda, J. B.; ...

2016-05-24

The use of a grazing incidence optic to selectively reflect K-shell fluorescence emission and isotope-specific lines from special nuclear materials is a highly desirable nondestructive analysis method for use in reprocessing fuel environments. Preliminary measurements have been performed, and a simulation suite has been developed to give insight into the design of the x ray optics system as a function of the source emission, multilayer coating characteristics, and general experimental configurations. As a result, the experimental results are compared to the predictions from our simulation toolkit to illustrate the ray-tracing capability and explore the effect of modified optics in futuremore » measurement campaigns.« less

Survey of statistical techniques used in validation studies of air pollution prediction models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bornstein, R D; Anderson, S F

1979-03-01

Statistical techniques used by meteorologists to validate predictions made by air pollution models are surveyed. Techniques are divided into the following three groups: graphical, tabular, and summary statistics. Some of the practical problems associated with verification are also discussed. Characteristics desired in any validation program are listed and a suggested combination of techniques that possesses many of these characteristics is presented.

Job Characteristics and Off-Job Activities as Predictors of Need for Recovery, Well-Being, and Fatigue

ERIC Educational Resources Information Center

Sonnentag, Sabine; Zijlstra, Fred R. H.

2006-01-01

Two empirical studies examined need for recovery (i.e., a person's desire to be temporarily relieved from demands in order to restore his or her resources) as a mediator in the relationship between poor job characteristics (high job demands, low job control) and high off-job demands, on the one hand, and fatigue and poor individual well-being, on…

Transient multivariable sensor evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vilim, Richard B.; Heifetz, Alexander

A method and system for performing transient multivariable sensor evaluation. The method and system includes a computer system for identifying a model form, providing training measurement data, generating a basis vector, monitoring system data from sensor, loading the system data in a non-transient memory, performing an estimation to provide desired data and comparing the system data to the desired data and outputting an alarm for a defective sensor.

Designing Inter-Organisational Collectivities for Dynamic Fit: Stability, maneuvrability and Application in Disaster Relief Endeavours

DTIC Science & Technology

2011-01-01

changed consumer preferences . Hence, static stability limits initial performance deviation (e.g., maintaining desired airplane altitude, maintaining...by changed consumer preferences . Hence, dynamic stability limits the duration of performance deviation (e.g., maintaining desired airplane altitude...altitude from wind gust. Initial resistance to deviation in profit level from change in consumer preferences . Dynamic stability Quickness of a

Why We Think We Can't Dance: Theory of Mind and Children's Desire to Perform

ERIC Educational Resources Information Center

Chaplin, Lan Nguyen; Norton, Michael I.

2015-01-01

Theory of mind (ToM) allows children to achieve success in the social world by understanding others' minds. A study with 3- to 12-year-olds, however, demonstrates that gains in ToM are linked to decreases in children's desire to engage in performative behaviors associated with health and well-being, such as singing and dancing. One hundred and…

Neural Correlates of Belief- and Desire-Reasoning in 7- and 8-year-old Children: An Event-Related Potential Study

PubMed Central

Bowman, Lindsay C.; Liu, David; Meltzoff, Andrew N.; Wellman, Henry M.

2012-01-01

Theory of mind requires belief- and desire-understanding. Event-related brain potential (ERP) research on belief- and desire-reasoning in adults found mid-frontal activations for both desires and beliefs, and selective right-posterior activations only for beliefs. Developmentally, children understand desires before beliefs; thus, a critical question concerns whether neural specialization for belief-reasoning exists in childhood or develops later. Neural activity was recorded as 7- and 8-year-olds (N = 18) performed the same diverse-desires, diverse-beliefs, and physical control tasks used in a previous adult ERP study. Like adults, mid-frontal scalp activations were found for belief- and desire-reasoning. Moreover, analyses using correct trials alone yielded selective right-posterior activations for belief-reasoning. Results suggest developmental links between increasingly accurate understanding of complex mental states and neural specialization supporting this understanding. PMID:22925510

NEW METHODOLOGY FOR DEVELOPMENT OF ORODISPERSIBLE TABLETS USING HIGH-SHEAR GRANULATION PROCESS.

PubMed

Ali, Bahaa E; Al-Shedfat, Ramadan I; Fayed, Mohamed H; Alanazi, Fars K

2017-05-01

Development of orodispersible delivery system of high mechanical properties and low disintegration time is a big challenge. The aim of the current work was to assess and optimize the high shear granulation process as a new methodology for development of orodispersible tablets of high quality attributes using design of experiment approach. A two factor, three levels (32), full factorial design was carried out to investigate the main and interaction effects of independent variables, water amount (XI) and granulation time (X2) on the characteristics of granules and final product, tablet. The produced granules were analyzed for their granule size, density and flowability. Furthermore, the produced tablets were tested for: weight variation, breaking force/ crushing strength, friability, disintegration time and drug dissolution. Regression analysis results of multiple linear models showed a high correlation between the adjusted R-squared and predicted R-squared for all granules and tablets characteristics, the difference is less than 0.2. All dependent responses of granules and tablets were found to be impacted significantly (p < 0.05) by the two independent variables. However, water amount demonstrated the most dominant effect for all granules and tablet characteristics as shown by higher its coefficient estimate for all selected responses. Numerical optimization using desirability function was performed to optimize the variables under study to provide orodispersible system within the USP limit with respect of mechanical properties and disintegration time. It was found that the higher desirability (0.915) could be attained at the low level pf water (180 g) and short granulation time (1.65 min). Eventually, this study provides the formulator with helpful information in selecting the proper level of water and granulation time to provide an orodispersible system of high crushing strength and very low disintegration time, when high shear granulation methodology was used as a method of manufacture.

Why women want children: defining the meaning of desire for children and the construction of an index.

PubMed

Wesley, Yvonne

2007-07-01

Many people view procreation as a purpose in life, justifying this idea by pointing towards a woman's natural biological characteristics. However, much of the literature supporting this position is void of studies that examine African-American women's desire for children. Therefore, the primary aims of this article are: 1) to review the literature on parenthood motivation; and 2) to describe the development, validation and reliability of the Modified Index of Parenthood Motivation. Within the first sample of 31 Black women, who served to confirm the Modified Index of Parenthood Motivation (MIPM), Wesley reported a reliability alpha coefficient of .765 for the MIPM. The second sample showed an alpha coefficient of.792, among a sample of 98 Black women of childbearing age. The MIPM offers investigators an opportunity to examine desire for children among women of African descent. Further research is needed to understand the impact of desire for children better among women with chronic illnesses such as HIV.

Ultrasound Thickness of Bladder Wall in Continent and Incontinent Women and Its Correlation with Cystometry

PubMed Central

Otsuki, Edney Norio; Oliveira, Emerson; Sartori, Marair Gracio Ferreira; Girão, Manoel João Batista Castelo; Jármy-Di Bella, Zsuzsanna Ilona Katalin

2014-01-01

Objective. To compare bladder wall thickness in two kinds of urinary incontinent women—stress urinary incontinence (SUI) and overactive bladder (OAB) with urodynamic detrusor overactivity (DO), and to compare them with continent patients by ultrasound, also, correlate with cystometric results in incontinent women. Methods. 91 women were divided into the following groups: continent (n = 31), SUI (n = 30), and DO (n = 30) groups after clinical evaluation and urodynamic test (only in incontinent women). Transvaginal ultrasound was performed to the bladder wall thickness (BWT) measurement. The mean of BWT was calculated and data were analyzed with ANOVA and Turkey's multiple comparison tests. Pearson's correlation coefficient (r) was used to compare two variables. Receiver operating characteristic (ROC) curve was performed to study BWT as a diagnostic parameter. Results. BWT in DO group was significantly higher than that in the other groups (P < 0.005). A moderate positive correlation was found between BWT and maximum bladder pressure during involuntary bladder contraction. There was no difference in BWT between SUI and continent groups. DO group had lower first desire to void and cystometric capacity. Maximum bladder pressure at detrusor contraction had a moderate positive correlation with BWT. The ROC revealed an area under the curve of 0.962 (95% CI, 0.90–1.01). Conclusions. DO patients have increased bladder wall thickness, lower first desire to void, and lower cystometric capacity. There was a moderate correlation between BWT and maximum bladder pressure during involuntary bladder contraction. PMID:25538959

Constrained spacecraft reorientation using mixed integer convex programming

NASA Astrophysics Data System (ADS)

Tam, Margaret; Glenn Lightsey, E.

2016-10-01

A constrained attitude guidance (CAG) system is developed using convex optimization to autonomously achieve spacecraft pointing objectives while meeting the constraints imposed by on-board hardware. These constraints include bounds on the control input and slew rate, as well as pointing constraints imposed by the sensors. The pointing constraints consist of inclusion and exclusion cones that dictate permissible orientations of the spacecraft in order to keep objects in or out of the field of view of the sensors. The optimization scheme drives a body vector towards a target inertial vector along a trajectory that consists solely of permissible orientations in order to achieve the desired attitude for a given mission mode. The non-convex rotational kinematics are handled by discretization, which also ensures that the quaternion stays unity norm. In order to guarantee an admissible path, the pointing constraints are relaxed. Depending on how strict the pointing constraints are, the degree of relaxation is tuneable. The use of binary variables permits the inclusion of logical expressions in the pointing constraints in the case that a set of sensors has redundancies. The resulting mixed integer convex programming (MICP) formulation generates a steering law that can be easily integrated into an attitude determination and control (ADC) system. A sample simulation of the system is performed for the Bevo-2 satellite, including disturbance torques and actuator dynamics which are not modeled by the controller. Simulation results demonstrate the robustness of the system to disturbances while meeting the mission requirements with desirable performance characteristics.

Aerodynamic Characterization of New Parachute Configurations for Low-Density Deceleration

NASA Technical Reports Server (NTRS)

Tanner, Christopher L.; Clark, Ian G.; Gallon, John C.; Rivellini, Tommaso P.; Witkowski, Allen

2013-01-01

The Low Density Supersonic Decelerator project performed a wind tunnel experiment on the structural design and geometric porosity of various sub-scale parachutes in order to inform the design of the 110ft nominal diameter flight test canopy. Thirteen different parachute configurations, including disk-gap-band, ring sail, disk sail, and star sail canopies, were tested at the National Full-scale Aerodynamics Complex 80- by 120-foot Wind Tunnel at NASA Ames Research Center. Canopy drag load, dynamic pressure, and canopy position data were recorded in order to quantify there lative drag performance and stability of the various canopies. Desirable designs would yield increased drag above the disk-gap-band with similar, or improved, stability characteristics. Ring sail parachutes were tested at geometric porosities ranging from 10% to 22% with most of the porosity taken from the shoulder region near the canopy skirt. The disk sail canopy replaced the rings lot portion of the ring sail canopy with a flat circular disk and wastested at geometric porosities ranging from 9% to 19%. The star sail canopy replaced several ringsail gores with solid gores and was tested at 13% geometric porosity. Two disk sail configurations exhibited desirable properties such as an increase of 6-14% in the tangential force coefficient above the DGB with essentially equivalent stability. However, these data are presented with caveats including the inherent differences between wind tunnel and flight behavior and qualitative uncertainty in the aerodynamic coefficients.

An algorithm for targeting finite burn maneuvers

NASA Technical Reports Server (NTRS)

Barbieri, R. W.; Wyatt, G. H.

1972-01-01

An algorithm was developed to solve the following problem: given the characteristics of the engine to be used to make a finite burn maneuver and given the desired orbit, when must the engine be ignited and what must be the orientation of the thrust vector so as to obtain the desired orbit? The desired orbit is characterized by classical elements and functions of these elements whereas the control parameters are characterized by the time to initiate the maneuver and three direction cosines which locate the thrust vector. The algorithm was built with a Monte Carlo capability whereby samples are taken from the distribution of errors associated with the estimate of the state and from the distribution of errors associated with the engine to be used to make the maneuver.

Participation in medical decision-making across Europe: An international longitudinal multicenter study.

PubMed

Bär Deucher, A; Hengartner, M P; Kawohl, W; Konrad, J; Puschner, B; Clarke, E; Slade, M; Del Vecchio, V; Sampogna, G; Égerházi, A; Süveges, Á; Krogsgaard Bording, M; Munk-Jørgensen, P; Rössler, W

2016-05-01

The purpose of this paper was to examine national differences in the desire to participate in decision-making of people with severe mental illness in six European countries. The data was taken from a European longitudinal observational study (CEDAR; ISRCTN75841675). A sample of 514 patients with severe mental illness from the study centers in Ulm, Germany, London, England, Naples, Italy, Debrecen, Hungary, Aalborg, Denmark and Zurich, Switzerland were assessed as to desire to participate in medical decision-making. Associations between desire for participation in decision-making and center location were analyzed with generalized estimating equations. We found large cross-national differences in patients' desire to participate in decision-making, with the center explaining 47.2% of total variance in the desire for participation (P<0.001). Averaged over time and independent of patient characteristics, London (mean=2.27), Ulm (mean=2.13) and Zurich (mean=2.14) showed significantly higher scores in desire for participation, followed by Aalborg (mean=1.97), where scores were in turn significantly higher than in Debrecen (mean=1.56). The lowest scores were reported in Naples (mean=1.14). Over time, the desire for participation in decision-making increased significantly in Zurich (b=0.23) and decreased in Naples (b=-0.14). In all other centers, values remained stable. This study demonstrates that patients' desire for participation in decision-making varies by location. We suggest that more research attention be focused on identifying specific cultural and social factors in each country to further explain observed differences across Europe. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Continuous performance measurement in flight systems. [sequential control model

NASA Technical Reports Server (NTRS)

Connelly, E. M.; Sloan, N. A.; Zeskind, R. M.

1975-01-01

The desired response of many man machine control systems can be formulated as a solution to an optimal control synthesis problem where the cost index is given and the resulting optimal trajectories correspond to the desired trajectories of the man machine system. Optimal control synthesis provides the reference criteria and the significance of error information required for performance measurement. The synthesis procedure described provides a continuous performance measure (CPM) which is independent of the mechanism generating the control action. Therefore, the technique provides a meaningful method for online evaluation of man's control capability in terms of total man machine performance.

No exceptional vigor found in hybrid pines tested

Treesearch

S. Little; H. A. Somes

1951-01-01

Hybrid trees, like hybrid corn, may have exceptional qualities their parents did not have. But extensive tests are needed to pick out the hybrids that have desirable characteristics such as exceptionally fast growth and good form.

Sandia Research and Development Board: Minutes of the 33rd Meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castle, M.

1950-02-08

Notes about the barometric fuzing system testing, drops of stockpile weapons requested by the Strategic Air Command, simultaneous drops and the interaction of the baro systems, changes of desired military characteristics of atomic weapons.

African American Girls’ Ideal Dating Relationship Now and In the Future

PubMed Central

Debnam, Katrina J.; Howard, Donna E.; Garza, Mary A.; Green, Kerry M.

2014-01-01

Adolescence is a particularly important and challenging time for developing long lasting romantic relationship patterns. However, limited empirical research has explored teen perceptions of ideal partner characteristics during adolescence or their significance to the quality of current and future relationships. Semi-structured in-depth interviews were conducted with 33 African American high school girls to shed light on the qualities desired in their dating relationships and relational factors that influence teen dating behaviors. Guided by the Social Ecological Framework, interviews were transcribed verbatim and entered into ATLAS.ti, for coding and analysis. Girls discussed the important influence of parents in choosing a partner and provided positive depictions of friendship and marriage with a suitable partner. More research is needed to understand how and why adolescents desire particular characteristics, how socialization shapes teen perceptions and how these preferences may be related to current and future adolescent dating choices, including violence perpetration and victimization. PMID:28943670

Production and characterization of a composite insulation material from waste polyethylene teraphtalates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurtulmus, Erhan; Karaboyacı, Mustafa; Yigitarslan, Sibel

2013-12-16

The pollution of polyethylene teraphtalate (PET) is in huge amounts due to the most widely usage as a packaging material in several industries. Regional pumice has several desirable characteristics such as porous structure, low-cost and light-weight. Considering the requirements approved by the Ministry of Public Works on isolation, composite insulation material consisting of PET and pumice was studied. Sheets of composites differing both in particle size of pumice and composition of polymer were produced by hot-molding technique. Characterization of new composite material was achieved by measuring its weight, density, flammability, endurance against both to common acids and bases, and tomore » a force applied, heat insulation and water adsorption capacity. The results of the study showed that produced composite material is an alternative building material due to its desirable characteristics; low weight, capability of low heat conduction.« less

Examining Mechanical Strength Characteristics of Selective Inhibition Sintered HDPE Specimens Using RSM and Desirability Approach

NASA Astrophysics Data System (ADS)

Rajamani, D.; Esakki, Balasubramanian

2017-09-01

Selective inhibition sintering (SIS) is a powder based additive manufacturing (AM) technique to produce functional parts with an inexpensive system compared with other AM processes. Mechanical properties of SIS fabricated parts are of high dependence on various process parameters importantly layer thickness, heat energy, heater feedrate, and printer feedrate. In this paper, examining the influence of these process parameters on evaluating mechanical properties such as tensile and flexural strength using Response Surface Methodology (RSM) is carried out. The test specimens are fabricated using high density polyethylene (HDPE) and mathematical models are developed to correlate the control factors to the respective experimental design response. Further, optimal SIS process parameters are determined using desirability approach to enhance the mechanical properties of HDPE specimens. Optimization studies reveal that, combination of high heat energy, low layer thickness, medium heater feedrate and printer feedrate yielded superior mechanical strength characteristics.

Determining Desirable Cursor Control Device Characteristics for NASA Exploration Missions

NASA Technical Reports Server (NTRS)

Sandor, Aniko; Holden, Kritina L.

2007-01-01

A test battery was developed for cursor control device evaluation: four tasks were taken from ISO 9241-9, and three from previous studies conducted at NASA. The tasks focused on basic movements such as pointing, clicking, and dragging. Four cursor control devices were evaluated with and without Extravehicular Activity (EVA) gloves to identify desirable cursor control device characteristics for NASA missions: 1) the Kensington Expert Mouse, 2) the Hulapoint mouse, 3) the Logitech Marble Mouse, and 4) the Honeywell trackball. Results showed that: 1) the test battery is an efficient tool for differentiating among input devices, 2) gloved operations were about 1 second slower and had at least 15% more errors; 3) devices used with gloves have to be larger, and should allow good hand positioning to counteract the lack of tactile feedback, 4) none of the devices, as designed, were ideal for operation with EVA gloves.

Advanced controls for airbreathing engines, volume 3: Allison gas turbine

NASA Technical Reports Server (NTRS)

Bough, R. M.

1993-01-01

The application of advanced control concepts to airbreathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for airbreathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two-phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 3 of these reports describes the studies performed by the Allison Gas Turbine Division.

Static and cyclic performance evaluation of sensors for human interface pressure measurement.

PubMed

Dabling, Jeffrey G; Filatov, Anton; Wheeler, Jason W

2012-01-01

Researchers and clinicians often desire to monitor pressure distributions on soft tissues at interfaces to mechanical devices such as prosthetics, orthotics or shoes. The most common type of sensor used for this type of applications is a Force Sensitive Resistor (FSR) as these are convenient to use and inexpensive. Several other types of sensors exist that may have superior sensing performance but are less ubiquitous or more expensive, such as optical or capacitive sensors. We tested five sensors (two FSRs, one optical, one capacitive and one fluid pressure) in a static drift and cyclic loading configuration. The results show that relative to the important performance characteristics for soft tissue pressure monitoring (i.e. hysteresis, drift), many of the sensors tested have significant limitations. The FSRs exhibited hysteresis, drift and loss of sensitivity under cyclic loading. The capacitive sensor had substantial drift. The optical sensor had some hysteresis and temperature-related drift. The fluid pressure sensor performed well in these tests but is not as flat as the other sensors and is not commercially available. Researchers and clinicians should carefully consider the convenience and performance trade-offs when choosing a sensor for soft-tissue pressure monitoring.

Advanced control for airbreathing engines, volume 1: Pratt and Whitney

NASA Technical Reports Server (NTRS)

Ralph, J. A.

1993-01-01

The application of advanced control concepts to air breathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for air breathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 1 of these reports describes the studies performed by Pratt & Whitney.

Advanced control for airbreathing engines, volume 2: General Electric aircraft engines

NASA Technical Reports Server (NTRS)

Bansal, Indar

1993-01-01

The application of advanced control concepts to air breathing engines may yield significant improvements in aircraft/engine performance and operability. Screening studies of advanced control concepts for air breathing engines were conducted by three major domestic aircraft engine manufacturers to determine the potential impact of concepts on turbine engine performance and operability. The purpose of the studies was to identify concepts which offered high potential yet may incur high research and development risk. A target suite of proposed advanced control concepts was formulated and evaluated in a two phase study to quantify each concept's impact on desired engine characteristics. To aid in the evaluation specific aircraft/engine combinations were considered: a Military High Performance Fighter mission, a High Speed Civil Transport mission, and a Civil Tiltrotor mission. Each of the advanced control concepts considered in the study are defined and described. The concept potential impact on engine performance was determined. Relevant figures of merit on which to evaluate the concepts are determined. Finally, the concepts are ranked with respect to the target aircraft/engine missions. A final report describing the screening studies was prepared by each engine manufacturer. Volume 2 of these reports describes the studies performed by GE Aircraft Engines.

Factors associated with desired fertility among HIV-positive women and men attending two urban clinics in Lilongwe, Malawi.

PubMed

Krashin, Jamie W; Haddad, Lisa B; Tweya, Hannock; Chiwoko, Jane; Ng'ambi, Wingston; Samala, Bernadette; Chaweza, Thomas; Tang, Jennifer H; Hosseinipour, Mina C; Phiri, Sam

2018-01-01

As access to antiretroviral therapy increases, more HIV-infected patients in sub-Saharan Africa may desire fertility. We conducted a cross-sectional study of reproductive health knowledge, attitudes and practices to identify factors associated with desired fertility among women and men receiving care at two large public HIV clinics in Lilongwe, Malawi. Research assistants administered questionnaires to participants. We performed descriptive, bivariable and multivariable analysis of factors related to desired fertility and of factors related to contraceptive non-use among participants who did not desire fertility. One-third of participants desired future children. Having a partner who desired fertility and having lower parity were associated with desiring children among both genders. For women, believing that pregnancy was unhealthy was associated with decreased fertility desire. Fifty-five percent of women and 69% of men who did not want children in the future reported using contraception at last intercourse. Increasing age, lower parity, and making the decision to use contraception herself were associated with contraceptive non-use among women who did not desire fertility. Having discussed family planning with his partner was associated with contraceptive use among men who did not desire fertility. Knowledge of these factors can guide reproductive health counseling and service provision.

Review of fluorescence guided surgery systems: identification of key performance capabilities beyond indocyanine green imaging

PubMed Central

DSouza, Alisha V.; Lin, Huiyun; Henderson, Eric R.; Samkoe, Kimberley S.; Pogue, Brian W.

2016-01-01

Abstract. There is growing interest in using fluorescence imaging instruments to guide surgery, and the leading options for open-field imaging are reviewed here. While the clinical fluorescence-guided surgery (FGS) field has been focused predominantly on indocyanine green (ICG) imaging, there is accelerated development of more specific molecular tracers. These agents should help advance new indications for which FGS presents a paradigm shift in how molecular information is provided for resection decisions. There has been a steady growth in commercially marketed FGS systems, each with their own differentiated performance characteristics and specifications. A set of desirable criteria is presented to guide the evaluation of instruments, including: (i) real-time overlay of white-light and fluorescence images, (ii) operation within ambient room lighting, (iii) nanomolar-level sensitivity, (iv) quantitative capabilities, (v) simultaneous multiple fluorophore imaging, and (vi) ergonomic utility for open surgery. In this review, United States Food and Drug Administration 510(k) cleared commercial systems and some leading premarket FGS research systems were evaluated to illustrate the continual increase in this performance feature base. Generally, the systems designed for ICG-only imaging have sufficient sensitivity to ICG, but a fraction of the other desired features listed above, with both lower sensitivity and dynamic range. In comparison, the emerging research systems targeted for use with molecular agents have unique capabilities that will be essential for successful clinical imaging studies with low-concentration agents or where superior rejection of ambient light is needed. There is no perfect imaging system, but the feature differences among them are important differentiators in their utility, as outlined in the data and tables here. PMID:27533438

Review of fluorescence guided surgery systems: identification of key performance capabilities beyond indocyanine green imaging

NASA Astrophysics Data System (ADS)

DSouza, Alisha V.; Lin, Huiyun; Henderson, Eric R.; Samkoe, Kimberley S.; Pogue, Brian W.

2016-08-01

There is growing interest in using fluorescence imaging instruments to guide surgery, and the leading options for open-field imaging are reviewed here. While the clinical fluorescence-guided surgery (FGS) field has been focused predominantly on indocyanine green (ICG) imaging, there is accelerated development of more specific molecular tracers. These agents should help advance new indications for which FGS presents a paradigm shift in how molecular information is provided for resection decisions. There has been a steady growth in commercially marketed FGS systems, each with their own differentiated performance characteristics and specifications. A set of desirable criteria is presented to guide the evaluation of instruments, including: (i) real-time overlay of white-light and fluorescence images, (ii) operation within ambient room lighting, (iii) nanomolar-level sensitivity, (iv) quantitative capabilities, (v) simultaneous multiple fluorophore imaging, and (vi) ergonomic utility for open surgery. In this review, United States Food and Drug Administration 510(k) cleared commercial systems and some leading premarket FGS research systems were evaluated to illustrate the continual increase in this performance feature base. Generally, the systems designed for ICG-only imaging have sufficient sensitivity to ICG, but a fraction of the other desired features listed above, with both lower sensitivity and dynamic range. In comparison, the emerging research systems targeted for use with molecular agents have unique capabilities that will be essential for successful clinical imaging studies with low-concentration agents or where superior rejection of ambient light is needed. There is no perfect imaging system, but the feature differences among them are important differentiators in their utility, as outlined in the data and tables here.

Touching moments: desire modulates the neural anticipation of active romantic caress

PubMed Central

Ebisch, Sjoerd J.; Ferri, Francesca; Gallese, Vittorio

2014-01-01

A romantic caress is a basic expression of affiliative behavior and a primary reinforcer. Given its inherent affective valence, its performance also would imply the prediction of reward values. For example, touching a person for whom one has strong passionate feelings likely is motivated by a strong desire for physical contact and associated with the anticipation of hedonic experiences. The present study aims at investigating how the anticipatory neural processes of active romantic caress are modulated by the intensity of the desire for affective contact as reflected by passionate feelings for the other. Functional magnetic resonance imaging scanning was performed in romantically involved partners using a paradigm that allowed to isolate the specific anticipatory representations of active romantic caress, compared with control caress, while testing for the relationship between neural activity and measures of feelings of passionate love for the other. The results demonstrated that right posterior insula activity in anticipation of romantic caress significantly co-varied with the intensity of desire for union with the other. This effect was independent of the sensory-affective properties of the performed touch, like its pleasantness. Furthermore, functional connectivity analysis showed that the same posterior insula cluster interacted with brain regions related to sensory-motor functions as well as to the processing and anticipation of reward. The findings provide insight on the neural substrate mediating between the desire for and the performance of romantic caress. In particular, we propose that anticipatory activity patterns in posterior insula may modulate subsequent sensory-affective processing of skin-to-skin contact. PMID:24616676

NTREES Testing and Operations Status

NASA Technical Reports Server (NTRS)

Emrich, Bill

2007-01-01

Nuclear Thermal Rockets or NTR's have been suggested as a propulsion system option for vehicles traveling to the moon or Mars. These engines are capable of providing high thrust at specific impulses at least twice that of today's best chemical engines. The performance constraints on these engines are mainly the result of temperature limitations on the fuel coupled with a limited ability to withstand chemical attack by the hot hydrogen propellant. To operate at maximum efficiency, fuel forms are desired which can withstand the extremely hot, hostile environment characteristic of NTR operation for at least several hours. The simulation of such an environment would require an experimental device which could simultaneously approximate the power, flow, and temperature conditions which a nuclear fuel element (or partial element) would encounter during NTR operation. Such a simulation would allow detailed studies of the fuel behavior and hydrogen flow characteristics under reactor like conditions to be performed. Currently, the construction of such a simulator has been completed at the Marshall Space Flight Center, and will be used in the future to evaluate a wide variety of fuel element designs and the materials of which they are fabricated. This present work addresses the operational status of the Nuclear Thermal Rocket Element Environmental Simulator or NTREES and some of the design considerations which were considered prior to and during its construction.

Numerical and Qualitative Contrasts of Two Statistical Models ...

EPA Pesticide Factsheets

Two statistical approaches, weighted regression on time, discharge, and season and generalized additive models, have recently been used to evaluate water quality trends in estuaries. Both models have been used in similar contexts despite differences in statistical foundations and products. This study provided an empirical and qualitative comparison of both models using 29 years of data for two discrete time series of chlorophyll-a (chl-a) in the Patuxent River estuary. Empirical descriptions of each model were based on predictive performance against the observed data, ability to reproduce flow-normalized trends with simulated data, and comparisons of performance with validation datasets. Between-model differences were apparent but minor and both models had comparable abilities to remove flow effects from simulated time series. Both models similarly predicted observations for missing data with different characteristics. Trends from each model revealed distinct mainstem influences of the Chesapeake Bay with both models predicting a roughly 65% increase in chl-a over time in the lower estuary, whereas flow-normalized predictions for the upper estuary showed a more dynamic pattern, with a nearly 100% increase in chl-a in the last 10 years. Qualitative comparisons highlighted important differences in the statistical structure, available products, and characteristics of the data and desired analysis. This manuscript describes a quantitative comparison of two recently-

Correlates of the Gudjonsson Suggestibility Scale in delinquent adolescents.

PubMed

Muris, Peter; Meesters, Cor; Merckelbach, Harald

2004-02-01

Correlations between scores on the Gudjonsson Suggestibility Scale and a number of relevant personality characteristics, i.e., intelligence, memory, social inadequacy, social desirability, and fantasy proneness, were examined in a sample of 71 delinquent boys. Analysis showed that intelligence and memory were negatively related to suggestibility scores. That is, lower memory and intelligence were associated with higher suggestibility. No significant correlations were found between suggestibility and other personality characteristics.

Study of electrical and chemical propulsion systems for auxiliary propulsion of large space systems. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Smith, W. W.; Clark, J. P.

1981-01-01

The objective was to determine the direction auxiliary propulsion research and development should take to best meet upcoming needs. The approach used was to define the important electrical and chemical propulsion characteristics in terms of the demands that will be imposed by future spacecraft. Comparison of these desired characteristics and capabilities with those presently available was then used to identify deficiencies.

Conceptions of mental illness: attitudes of mental health professionals and the general public.

PubMed

Stuber, Jennifer P; Rocha, Anita; Christian, Ann; Link, Bruce G

2014-04-01

The authors compared attitudes of the U.S. general public and of mental health professionals about the competence and perceived dangerousness of people with mental health problems and the desire for social distance from them. Factors related to negative attitudes and the desire for social distance also were examined. Vignettes describing individuals meeting DSM-IV criteria for major depression and schizophrenia were included in the 2006 General Social Survey (GSS) and a 2009 study of mental health professionals, and responses were descriptively compared (GSS, N=397 responses to depression vignette, N=373 responses to schizophrenia vignette; 731 mental health professionals responded to both vignettes). Regression analyses examined whether demographic and provider characteristics were associated with perceptions of less competence and perceived dangerousness of the vignette character and with respondents' desire for social distance. Compared with the American public, mental health professionals had significantly more positive attitudes toward people with mental health problems. However, some providers' conceptions about the dangerousness of people with schizophrenia and provider desire for social distance from clients in work and personal situations were concerning. Younger age, self-identifying as non-Hispanic white, being female, having at least a four-year college degree, being familiar with mental illness, and certain job titles and more years of experience in the mental health field were predictive of more positive conceptions. Although mental health professionals held more positive attitudes than the general public about people with mental health problems, strong stereotypes persisted in both groups, especially concerning schizophrenia. This study identified several demographic and provider characteristics that can inform intervention strategies in both groups.

HIGH SHEAR GRANULATION PROCESS: ASSESSING IMPACT OF FORMULATION VARIABLES ON GRANULES AND TABLETS CHARACTERISTICS OF HIGH DRUG LOADING FORMULATION USING DESIGN OF EXPERIMENT METHODOLOGY.

PubMed

Fayed, Mohamed H; Abdel-Rahman, Sayed I; Alanazi, Fars K; Ahmed, Mahrous O; Tawfeek, Hesham M; Ali, Bahaa E

2017-03-01

High shear wet granulation is a significant component procedure in the pharmaceutical industry. The objective of the study was to investigate the influence of two independent formulation variables; polyvinypyrrolidone (PVP) as a binder (X,) and croscarmellose sodium (CCS) as a disintegrant (X2) on the crit- ical quality attributes of acetaminophen granules and their corresponding tablets using design of experiment (DoE) approach. A two factor, three level (32) full factorial design has been applied; each variable was investi- gated at three levels to characterize their strength and interaction. The dried granules have been analyzed for their density, granule size and flowability. Additionally, the produced tablets have been investigated for: break- ing force, friability, disintegration time and t. of drug dissolution. The analysis of variance (ANOVA) showed that the two variables had a significant impact (p < 0.05) on granules and tablets characteristics, while only the binder concentration influenced the tablets friability. Furthermore, significant interactions (p < 0.05) between the two variables, for granules and tablets attributes, were also found. However, variables interaction showed minimal effect for granules flowability as well as tablets friability. Desirability function was carried out to opti- mize the variables under study to obtain product within the USP limit. It was found that the higher desirability (0.985) could be obtained at the medium level of PVP and low level of CCS. Ultimately, this study supplies the formulator with beneficial tools in selecting the proper level of binder and disintegrant to attain product with desired characteristics.

A STANDARDIZED ASSESSMENT METHOD (SAM) FOR RIVERINE MACROINVERTEBRATES

EPA Science Inventory

A macroinvertebrate sampling method for large rivers based on desirable characteristics of existing nonwadeable methods was developed and tested. Six sites each were sampled on the Great Miami and Kentucky Rivers, reflecting a human disturbance gradient. Samples were collected ...

An evaluation of Brifen wire rope safety fence.

DOT National Transportation Integrated Search

2013-01-01

Three : - : strand : cable barriers were first developed in the 1960s and found to have several desirable : characteristics as compared to other roadside barriers such as guard rail : . : Brifen Wire Rope Safety Fence is : a four strand woven wire...

Rapid infrared heating of a surface

DOEpatents

Sikka, Vinod K.; Blue, Craig A.; Ohriner, Evan Keith

2002-01-01

High energy flux infrared heaters are used to treat an object having a surface section and a base section such that a desired characteristic of the surface section is physically, chemically, or phasically changed while the base section remains unchanged.

Rapid infrared heating of a surface

DOEpatents

Sikka, Vinod K.; Blue, Craig A.; Ohriner, Evan Keith

2001-01-01

High energy flux infrared heaters are used to treat an object having a surface section and a base section such that a desired characteristic of the surface section is physically, chemically, or phasically changed while the base section remains unchanged.

Rapid infrared heating of a surface

DOEpatents

Sikka, Vinod K.; Blue, Craig A.; Ohriner, Evan Keith

2003-12-23

High energy flux infrared heaters are used to treat an object having a surface section and a base section such that a desired characteristic of the surface section is physically, chemically, or phasically changed while the base section remains unchanged.

Development of guidelines for accommodating safe and desirable pedestrian activity within the highway environment.

DOT National Transportation Integrated Search

1975-01-01

This study develops general guidelines for planning and evaluating suburban pedestrian systems. Pedestrian characteristics and capabilities which affect walking demand are summarized using the results of previous research. Reported research results a...

Rail passenger equipment crashworthiness testing requirements and implementation

DOT National Transportation Integrated Search

2000-11-01

This paper describes the requirements and the implementation of a series of impact tests of rail passenger equipment. The test : requirements the desired measurements are dictated by the : characteristics of the vehicle, as well as uncertainties in t...

Trip Planning State of the Practice.

DOT National Transportation Integrated Search

2002-07-01

Automated trip planning is one of the easiest ways for transit users to identify their best choice of routes using the Internet. Trip planners use an input form to obtain information on desired trip characteristics then automatically generate an itin...

Young women's perceptions of fertility-related information and fertility distress before surgery for ovarian cysts.

PubMed

Lind, Tekla; Lampic, Claudia; Hammarström, Margareta; Rodriguez-Wallberg, Kenny

2013-11-01

To investigate young women's reproductive desire and perceptions of fertility-related information when scheduled for ovarian cyst surgery with a possible impact on fertility. Cross-sectional study. University Hospital. Women of reproductive age (n = 106, mean age 32.3 years, range 18-44 years) with a diagnosis of ovarian cyst and scheduled ovarian cyst surgery between March 2011 and September 2012 were included. The women answered a questionnaire after the presurgery consultation with the gynecologist. The questionnaire included study-specific measures of reproductive desire, perception of fertility-related information received, worry about future fertility and sociodemographic characteristics. Reproductive desire and recalled information on the impact of surgery on fertility. A high proportion of the women (72%) reported a desire for having children in the future and more than half of them (58%) recalled receiving information about the impact of surgery on fertility. In a multivariable logistic regression model adjusted for parity, education and age, a desire to have children increased the likelihood of recalling having received fertility-related information (odds ratio 3.2, 95% CI 1.1-9.2). Almost half of women with reproductive desire had ovarian surgery without recalling a discussion of fertility issues. Development of written information or interactive information might improve women's perception of fertility-related information. © 2013 Nordic Federation of Societies of Obstetrics and Gynecology.

How much does what you eat matter? The potential role of meal size, fat content, and gender on ratings of desirability.

PubMed

Yantcheva, B; Brindal, E

2013-08-01

This study examined how the amount and type of food that a person eats affects perceptions of their personal desirability, femininity/masculinity, and body size while accounting for any assumed similarity biases. Female students (18 to 59 years old) were recruited through the School of Psychology at the University of Adelaide. Participants (n = 191) rated the characteristics of a fictional person based on information in a personal profile. Profiles were identical aside from experimental manipulations of gender (male/female), meal size (small/large) and meal type (regular fat/high fat) with meal manipulations calculated using nutrient recommendations. Ratings of desirability and body size were affected primarily by meal type with targets described as eating a regular fat meal seen as more desirable (M = 5.40, SD = 0.56) and thinner (M = 3.93, SD = 1.05) than those having a high fat meal (M = 5.09, SD = 0.66; M = 4.29, SD = 1.04) (p = .001). Meal size manipulations affected only ratings of body size with larger meals (M = 4.25, SD = 0.88) resulting in higher ratings relative to smaller meals (M = 3.96, SD = 1.20) (p = .036). Despite a suggestion of interactions between target gender and both meal characteristics for ratings of femininity/masculinity in our results, post-hoc analyses largely failed to reveal any pairwise differences. Perceived similarity to the target did relate to levels of desirability (p = .006), and self-esteem positively associated with ratings of target body size (p = .010). Even though men's perceptions of eating behaviours were not reported in this paper, these findings have implications for a better understanding of social pressures faced not only by women, but also for men, as potentially both genders may be affected by eating norms regarding the healthiness of a meal. Copyright © 2013 Elsevier Ltd. All rights reserved.

The measurement of childbearing motivation in couples considering the use of assisted reproductive technology.

PubMed

Miller, Warren B; Millstein, Susan G; Pasta, David J

2008-01-01

Relatively little is known about the motivational antecedents to the use of assisted reproductive technology (ART). In this paper we measure the fertility motivations of infertile couples who are considering the use of ART, using an established instrument, the Childbearing Questionnaire (CBQ). Our sample consists of 214 men and 216 women who were interviewed at home after an initial screening for ART but before making a final decision. We conducted two sets of analyses with the obtained data. In one set, we compared the scores on scales and subscales of the CBQ for the males and females in our sample with the scores for males and females from a comparable normative sample. For these analyses we first examined sample and gender differences with a four-group analysis of variance. We then conducted a series of linear models that included background characteristics as covariates and interactions between sample, gender, and age and between those three variables and the background characteristics. The results showed the expected higher positive and lower negative motivations in the ART sample and a significant effect on positive motivations of the interaction between sample and age. In the second set of analyses, we developed several new subscales relevant to facets of the desire for a child that appear to be important in ART decision-making. These facets include the desire to be genetically related to the child and the desire to experience pregnancy and childbirth. A third facet, the desire for parenthood, is already well covered by the existing subscales. The results showed the new subscales to have satisfactory reliability and validity. The results also showed that the original and new subscales predicted the three facets of the desire for a child in a multivariate context. We conclude with a general discussion of the way our findings relate both to ART decision-making and to further research on the motivations that drive it.

Delayed Fertility Transition among Indigenous Women: A Case Study in the Ecuadoran Amazon

PubMed Central

Davis, Jason; Gray, Clark; Bilsborrow, Richard

2015-01-01

CONTEXT Communities indigenous to the Amazon are among the few remaining worldwide still practicing near natural fertility, without the use of modern contraceptives. Given the large proportion of women desiring no more births, information on the challenges women there face in limiting fertility would be useful. METHODS Samples of women of reproductive age from five indigenous ethnic groups in the Northern Ecuadorian Amazon were surveyed in 2001 and 2012. Cross-sectional and longitudinal analyses examined married women’s desire for another child at both times and modern contraceptive use in 2012, as well as determinants of a change in women’s desire to have more children and of the number of children born during the study period. RESULTS In 2001, 48% of married women desired another child, 2% used a modern contraceptive and 50% had an unmet need for limiting; in 2012, the proportions were 40%, 19% and 47%, respectively. The total fertility rate was 7.9 in 2001 and 7.0 in 2012. Characteristics associated with wanting another child in 2001 and 2012 included parity (odds ratios, 0.6 and 0.4, respectively) and experience of a child death (2.0 each); characteristics associated with contraceptive use in 2012 included desire for another child, experience of a child death and presence of a community health worker (0.3–0.5). Number of children born was positively associated, and the square of the term negatively associated, with no longer wanting more children in 2012 among women who wanted more in 2001 (odds ratios, 2.1 and 0.9, respectively). CONCLUSIONS Indigenous women in the Northern Ecuadorian Amazon appear to be transitioning to lower fertility. Insufficient access to credible information about the safety and efficacy of modern contraceptives, however, may slow the transition. International Perspectives on Sexual and Reproductive Health, 2015, 41(1):TK. PMID:25856232

Designing Preclinical Instruction for Psychomotor Skills (II)--Instructional Engineering: Task Analysis.

ERIC Educational Resources Information Center

Knight, G. William; And Others

1994-01-01

The first step in engineering the instruction of dental psychomotor skills, task analysis, is explained. A chart details the procedural, cognitive, desired-criteria, and desired-performance analysis of a single task, occlusal preparation for amalgam restoration with carious lesion. (MSE)

Financial motivation to work among people with psychiatric disorders.

PubMed

Serowik, Kristin L; Rowe, Michael; Black, Anne C; Ablondi, Karen; Fiszdon, Joanna; Wilber, Charles; Rosen, Marc I

2014-08-01

Supported employment is an effective intervention for people with serious mental illnesses (SMI) but is underutilized. Clients' desire to work might be heightened by programs that provide counseling about managing one's funds, since money management helps people become more aware of the advantages of having money. To analyze the thoughts of recently homeless or hospitalized persons with SMI concerning their personal finances and employment. We interviewed 49 people with SMI about their finances, reviewed transcripts and analyzed their baseline characteristics. Twenty of the 49 participants spontaneously expressed a desire to work in order to earn more money. Those who expressed a desire to work managed their money significantly better than those who did not. Discussion of finances, such as that fostered by money management programs, may promote engagement in vocational rehabilitation and working for pay.

Three-dimensional desirability spaces for quality-by-design-based HPLC development.

PubMed

Mokhtar, Hatem I; Abdel-Salam, Randa A; Hadad, Ghada M

2015-04-01

In this study, three-dimensional desirability spaces were introduced as a graphical representation method of design space. This was illustrated in the context of application of quality-by-design concepts on development of a stability indicating gradient reversed-phase high-performance liquid chromatography method for the determination of vinpocetine and α-tocopheryl acetate in a capsule dosage form. A mechanistic retention model to optimize gradient time, initial organic solvent concentration and ternary solvent ratio was constructed for each compound from six experimental runs. Then, desirability function of each optimized criterion and subsequently the global desirability function were calculated throughout the knowledge space. The three-dimensional desirability spaces were plotted as zones exceeding a threshold value of desirability index in space defined by the three optimized method parameters. Probabilistic mapping of desirability index aided selection of design space within the potential desirability subspaces. Three-dimensional desirability spaces offered better visualization and potential design spaces for the method as a function of three method parameters with ability to assign priorities to this critical quality as compared with the corresponding resolution spaces. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Aircraft compass characteristics

NASA Technical Reports Server (NTRS)

Peterson, John B; Smith, Clyde W

1937-01-01

A description of the test methods used at the National Bureau of Standards for determining the characteristics of aircraft compasses is given. The methods described are particularly applicable to compasses in which mineral oil is used as the damping liquid. Data on the viscosity and density of certain mineral oils used in United States Navy aircraft compasses are presented. Characteristics of Navy aircraft compasses IV to IX and some other compasses are shown for the range of temperatures experienced in flight. Results of flight tests are presented. These results indicate that the characteristic most desired in a steering compass is a short period and, in a check compass, a low overswing.

Helicopter roll control effectiveness criteria program summary

NASA Technical Reports Server (NTRS)

Heffley, Robert K.; Bourne, Simon M.; Mnich, Marc A.

1988-01-01

A study of helicopter roll control effectiveness is summarized for the purpose of defining military helicopter handling qualities requirements. The study is based on an analysis of pilot-in-the-loop task performance of several basic maneuvers. This is extended by a series of piloted simulations using the NASA Ames Vertical Motion Simulator and selected flight data. The main results cover roll control power and short-term response characteristics. In general the handling qualities requirements recommended are set in conjunction with desired levels of flight task and maneuver response which can be directly observed in actual flight. An important aspect of this, however, is that vehicle handling qualities need to be set with regard to some quantitative aspect of mission performance. Specific examples of how this can be accomplished include a lateral unmask/remask maneuver in the presence of a threat and an air tracking maneuver which recognizes the kill probability enhancement connected with decreasing the range to the target. Conclusions and recommendations address not only the handling qualities recommendations, but also the general use of flight simulators and the dependence of mission performance on handling qualities.

Performance of Axial-Flow Supersonic Compressor of the XJ55-FF-1 Turbojet Engine. IV - Analysis of Compressor Operation over a Range of Equivalent Tip Speeds from 801 to 1614 Feet Per Second

NASA Technical Reports Server (NTRS)

Graham, Robert C.; Hartmann, Melvin J.

1949-01-01

An investigation was conducted to determine the performance characteristics of the axial-flow supersonic compressor of the XJ55-FF-1 turbojet engine. An analysis of the performance of the rotor was made based on detailed flow measurements behind the rotor. The compressor apparently did not obtain the design normal-shock configuration in this investigation. A large redistribution of mass occurred toward the root of the rotor over the entire speed range; this condition was so acute at design speed that the tip sections were completely inoperative. The passage pressure recovery at maximum pressure ratio at 1614 feet per second varied from a maximum of 0.81 near the root to 0.53 near the tip, which indicated very poor efficiency of the flow process through the rotor. The results, however, indicated that the desired supersonic operation may be obtained by decreasing the effective contraction ratio of the rotor blade passage.

Assessment of WENO-extended two-fluid modelling in compressible multiphase flows

NASA Astrophysics Data System (ADS)

Kitamura, Keiichi; Nonomura, Taku

2017-03-01

The two-fluid modelling based on an advection-upwind-splitting-method (AUSM)-family numerical flux function, AUSM+-up, following the work by Chang and Liou [Journal of Computational Physics 2007;225: 840-873], has been successfully extended to the fifth order by weighted-essentially-non-oscillatory (WENO) schemes. Then its performance is surveyed in several numerical tests. The results showed a desired performance in one-dimensional benchmark test problems: Without relying upon an anti-diffusion device, the higher-order two-fluid method captures the phase interface within a fewer grid points than the conventional second-order method, as well as a rarefaction wave and a very weak shock. At a high pressure ratio (e.g. 1,000), the interpolated variables appeared to affect the performance: the conservative-variable-based characteristic-wise WENO interpolation showed less sharper but more robust representations of the shocks and expansions than the primitive-variable-based counterpart did. In two-dimensional shock/droplet test case, however, only the primitive-variable-based WENO with a huge void fraction realised a stable computation.

A multifunctional biphasic water splitting catalyst tailored for integration with high-performance semiconductor photoanodes

DOE PAGES

Yang, Jinhui; Cooper, Jason K.; Toma, Francesca M.; ...

2016-11-07

Artificial photosystems are advanced by the development of conformal catalytic materials that promote desired chemical transformations, while also maintaining stability and minimizing parasitic light absorption for integration on surfaces of semiconductor light absorbers. We demonstrate that multifunctional, nanoscale catalysts that enable high-performance photoelectrochemical energy conversion can be engineered by plasma-enhanced atomic layer deposition. The collective properties of tailored Co 3 O 4 /Co(OH) 2 thin films simultaneously provide high activity for water splitting, permit efficient interfacial charge transport from semiconductor substrates, and enhance durability of chemically sensitive interfaces. Furthermore, these films comprise compact and continuous nanocrystalline Co 3 O 4more » spinel that is impervious to phase transformation and impermeable to ions, thereby providing effective protection of the underlying substrate. Moreover, a secondary phase of structurally disordered and chemically labile Co(OH) 2 is introduced to ensure a high concentration of catalytically active sites. Application of this coating to photovoltaic p + n-Si junctions yields best reported performance characteristics for crystalline Si photoanodes.« less

Grading smart sensors: Performance assessment and ranking using familiar scores like A+ to D-

NASA Astrophysics Data System (ADS)

Kessel, Ronald T.

2005-03-01

Starting with the supposition that the product of smart sensors - whether autonomous, networked, or fused - is in all cases information, it is shown here using information theory how a metric Q, ranging between 0 and 100%, can be derived to assess the quality of the information provided. The analogy with student grades is immediately evident and elaborated. As with student grades, numerical percentages suggest more precision than can be justified, so a conversion to letter grades A+ to D- is desirable. Owing to the close analogy with familiar academic grades, moreover, the new grade is a measure of effectiveness (MOE) that commanders and decision makers should immediately appreciate and find quite natural, even if they do not care to follow the methodology behind the performance test, as they focus on higher-level strategic matters of sensor deployment or procurement. The metric is illustrated by translating three specialist performance tests - the Receiver Operating Characteristic (ROC) curve, the Constant False Alarm Rate (CFAR) approach, and confusion matrices - into letter grades for use then by strategists. Actual military and security systems are included among the examples.

Evaluating standard terminologies for encoding allergy information.

PubMed

Goss, Foster R; Zhou, Li; Plasek, Joseph M; Broverman, Carol; Robinson, George; Middleton, Blackford; Rocha, Roberto A

2013-01-01

Allergy documentation and exchange are vital to ensuring patient safety. This study aims to analyze and compare various existing standard terminologies for representing allergy information. Five terminologies were identified, including the Systemized Nomenclature of Medical Clinical Terms (SNOMED CT), National Drug File-Reference Terminology (NDF-RT), Medication Dictionary for Regulatory Activities (MedDRA), Unique Ingredient Identifier (UNII), and RxNorm. A qualitative analysis was conducted to compare desirable characteristics of each terminology, including content coverage, concept orientation, formal definitions, multiple granularities, vocabulary structure, subset capability, and maintainability. A quantitative analysis was also performed to compare the content coverage of each terminology for (1) common food, drug, and environmental allergens and (2) descriptive concepts for common drug allergies, adverse reactions (AR), and no known allergies. Our qualitative results show that SNOMED CT fulfilled the greatest number of desirable characteristics, followed by NDF-RT, RxNorm, UNII, and MedDRA. Our quantitative results demonstrate that RxNorm had the highest concept coverage for representing drug allergens, followed by UNII, SNOMED CT, NDF-RT, and MedDRA. For food and environmental allergens, UNII demonstrated the highest concept coverage, followed by SNOMED CT. For representing descriptive allergy concepts and adverse reactions, SNOMED CT and NDF-RT showed the highest coverage. Only SNOMED CT was capable of representing unique concepts for encoding no known allergies. The proper terminology for encoding a patient's allergy is complex, as multiple elements need to be captured to form a fully structured clinical finding. Our results suggest that while gaps still exist, a combination of SNOMED CT and RxNorm can satisfy most criteria for encoding common allergies and provide sufficient content coverage.

Effect of Thermal Budget on the Electrical Characterization of Atomic Layer Deposited HfSiO/TiN Gate Stack MOSCAP Structure

PubMed Central

Khan, Z. N.; Ahmed, S.; Ali, M.

2016-01-01

Metal Oxide Semiconductor (MOS) capacitors (MOSCAP) have been instrumental in making CMOS nano-electronics realized for back-to-back technology nodes. High-k gate stacks including the desirable metal gate processing and its integration into CMOS technology remain an active research area projecting the solution to address the requirements of technology roadmaps. Screening, selection and deposition of high-k gate dielectrics, post-deposition thermal processing, choice of metal gate structure and its post-metal deposition annealing are important parameters to optimize the process and possibly address the energy efficiency of CMOS electronics at nano scales. Atomic layer deposition technique is used throughout this work because of its known deposition kinetics resulting in excellent electrical properties and conformal structure of the device. The dynamics of annealing greatly influence the electrical properties of the gate stack and consequently the reliability of the process as well as manufacturable device. Again, the choice of the annealing technique (migration of thermal flux into the layer), time-temperature cycle and sequence are key parameters influencing the device’s output characteristics. This work presents a careful selection of annealing process parameters to provide sufficient thermal budget to Si MOSCAP with atomic layer deposited HfSiO high-k gate dielectric and TiN gate metal. The post-process annealing temperatures in the range of 600°C -1000°C with rapid dwell time provide a better trade-off between the desirable performance of Capacitance-Voltage hysteresis and the leakage current. The defect dynamics is thought to be responsible for the evolution of electrical characteristics in this Si MOSCAP structure specifically designed to tune the trade-off at low frequency for device application. PMID:27571412

Evaluating standard terminologies for encoding allergy information

PubMed Central

Goss, Foster R; Zhou, Li; Plasek, Joseph M; Broverman, Carol; Robinson, George; Middleton, Blackford; Rocha, Roberto A

2013-01-01

Objective Allergy documentation and exchange are vital to ensuring patient safety. This study aims to analyze and compare various existing standard terminologies for representing allergy information. Methods Five terminologies were identified, including the Systemized Nomenclature of Medical Clinical Terms (SNOMED CT), National Drug File–Reference Terminology (NDF-RT), Medication Dictionary for Regulatory Activities (MedDRA), Unique Ingredient Identifier (UNII), and RxNorm. A qualitative analysis was conducted to compare desirable characteristics of each terminology, including content coverage, concept orientation, formal definitions, multiple granularities, vocabulary structure, subset capability, and maintainability. A quantitative analysis was also performed to compare the content coverage of each terminology for (1) common food, drug, and environmental allergens and (2) descriptive concepts for common drug allergies, adverse reactions (AR), and no known allergies. Results Our qualitative results show that SNOMED CT fulfilled the greatest number of desirable characteristics, followed by NDF-RT, RxNorm, UNII, and MedDRA. Our quantitative results demonstrate that RxNorm had the highest concept coverage for representing drug allergens, followed by UNII, SNOMED CT, NDF-RT, and MedDRA. For food and environmental allergens, UNII demonstrated the highest concept coverage, followed by SNOMED CT. For representing descriptive allergy concepts and adverse reactions, SNOMED CT and NDF-RT showed the highest coverage. Only SNOMED CT was capable of representing unique concepts for encoding no known allergies. Conclusions The proper terminology for encoding a patient's allergy is complex, as multiple elements need to be captured to form a fully structured clinical finding. Our results suggest that while gaps still exist, a combination of SNOMED CT and RxNorm can satisfy most criteria for encoding common allergies and provide sufficient content coverage. PMID:23396542

Women and Entrepreneurship. ERIC Digest.

ERIC Educational Resources Information Center

Kerka, Sandra

The spectrum of women-owned businesses ranges from full corporations to microenterprises. Women business owners share many characteristics and motivations of business owners generally; other factors are dissatisfaction with "glass ceiling" limits, desire for job flexibility, and age discrimination. Women entrepreneurs often face barriers…

Integration of bicycling and walking facilities into the infrastructure of urban communities : [research brief].

DOT National Transportation Integrated Search

2012-02-01

Many manuals, handbooks and web resources exist that provide guidance on planning for and designing bicycle and pedestrian facilities. However few of these resources emphasize program and infrastructure characteristics most desired by current (and po...

EPDM rocket motor insulation

NASA Technical Reports Server (NTRS)

Guillot, David G. (Inventor); Harvey, Albert R. (Inventor)

2003-01-01

A novel and improved EPDM formulation for a solid propellant rocket motor is described wherein hexadiene EPDM monomer components are replaced by alkylidene norbornene components and with appropriate adjustment of curing and other additives functionally-required rheological and physical characteristics are achieved with the desired compatibility with any one of a plurality of solid filler materials, e.g. powder silica, carbon fibers or aramid fibers, and with appropriate adhesion and extended storage or shelf life characteristics.

EPDM rocket motor insulation

NASA Technical Reports Server (NTRS)

Guillot, David G. (Inventor); Harvey, Albert R. (Inventor)

2008-01-01

A novel and improved EPDM formulation for a solid propellant rocket motor is described wherein hexadiene EPDM monomer components are replaced by alkylidene norbornene components, and, with appropriate adjustment of curing and other additives, functionally required rheological and physical characteristics are achieved with the desired compatibility with any one of a plurality of solid filler materials, e.g., powder silica, carbon fibers or aramid fibers, and with appropriate adhesion and extended storage or shelf-life characteristics.

EPDM rocket motor insulation

NASA Technical Reports Server (NTRS)

Guillot, David G. (Inventor); Harvey, Albert R. (Inventor)

2004-01-01

A novel and improved EPDM formulation for a solid propellant rocket motor is described wherein hexadiene EPDM monomer components are replaced by alkylidene norbornene components, and, with appropriate adjustment of curing and other additives, functionally required rheological and physical characteristics are achieved with the desired compatibility with any one of a plurality of solid filler materials, e.g., powder silica, carbon fibers or aramid fibers, and with appropriate adhesion and extended storage or shelf-life characteristics.

Advanced CFD Methods for Hypervelocity Wind Tunnels

DTIC Science & Technology

2011-03-10

Mach 14 nozzle produces non-uniformities in the test section flow that are not desirable [1,2]. Calibration runs with Pitot pressure rakes suggest...flows is presented. The grid is based on the characteristic lines of the supersonic regions of the flow. This allows for grid alignment and clustering...novel grid generation scheme for hypersonic nozzle flows is presented. The grid is based on the characteristic lines of the supersonic regions of the

Experimental aerodynamic characteristics at Mach numbers from 0.60 to 2.70 of two supersonic cruise fighter configurations

NASA Technical Reports Server (NTRS)

Dollyhigh, S. M.

1979-01-01

Two 0.085-scale full span wind-tunnel models of a Mach 1.60 design supercruiser configuration were tested at Mach numbers from 0.60 to 2.70. One model incorporated a varying dihedral (swept-up) wing to obtain the desired lateral-directional characteristics; the other incorporated more conventional twin vertical tails. The data from the wind-tunnel tests are presented without analysis.

Recruitment, training outcomes, retention, and performance of community health advisors in two tobacco control interventions for Latinos.

PubMed

Woodruff, Susan I; Candelaria, Jeanette I; Elder, John P

2010-04-01

Community Health Advisors (CHAs) are indigenous lay health advisors who, with training, can create health awareness, disseminate health information and support behavior change in their communities. Little data are available that describe the characteristics, recruitment, training, retention, and performance of CHAs. The present study described the characteristics, recruitment process, training outcomes, retention activities, and performance of two sets of CHAs who delivered tobacco-related interventions in the local Latino community. The Tobacco Control in Latino Communities (TCLC) Center trained 35 CHAs to conduct either a smoking cessation program for Spanish-speaking adult smokers or a behavioral problem-solving intervention to reduce environmental tobacco smoke (ETS) exposure among low-income Latino children. Theoretical psychosocial constructs related to behavior change, general self-esteem, general self-efficacy, and demographics were collected from CHAs before and after training. Additional measures captured the level of professionalism exercised and effort undertaken by the CHAs, as well actual outcomes of their efforts. Of the 33 women and 2 men CHAs recruited, 86% were originally from Mexico, most had a high school education, most were married, and the average monthly household income was $1,100-$1,400. Mean participant age was 42 years, and level of acculturation was relatively low. There were changes in the desired direction pre-to-post training for both ETS and smoking cessation program CHAs for most of the psychosocial constructs. Expert ratings of CHA performance were good, and recipients of the CHAs' efforts showed positive changes in behavior. This information may aid in planning for recruitment and evaluation of CHAs for future tobacco control programs.

Semiconducting compounds and devices incorporating same

DOEpatents

Marks, Tobin J; Facchetti, Antonio; Boudreault, Pierre-Luc; Miyauchi, Hiroyuki

2014-06-17

Disclosed are molecular and polymeric compounds having desirable properties as semiconducting materials. Such compounds can exhibit desirable electronic properties and possess processing advantages including solution-processability and/or good stability. Organic transistor and photovoltaic devices incorporating the present compounds as the active layer exhibit good device performance.

Semiconducting compounds and devices incorporating same

DOEpatents

Marks, Tobin J.; Facchetti, Antonio; Boudreault, Pierre-Luc; Miyauchi, Hiroyuki

2016-01-19

Disclosed are molecular and polymeric compounds having desirable properties as semiconducting materials. Such compounds can exhibit desirable electronic properties and possess processing advantages including solution-processability and/or good stability. Organic transistor and photovoltaic devices incorporating the present compounds as the active layer exhibit good device performance.

Graphene-Reinforced Aluminum Matrix Composites: A Review of Synthesis Methods and Properties

NASA Astrophysics Data System (ADS)

Chen, Fei; Gupta, Nikhil; Behera, Rakesh K.; Rohatgi, Pradeep K.

2018-06-01

Graphene-reinforced aluminum (Gr-Al) matrix nanocomposites (NCs) have attracted strong interest from both research and industry in high-performance weight-sensitive applications. Due to the vastly different bonding characteristics of the Al matrix (metallic) and graphene (in-plane covalent + inter-plane van der Waals), the graphene phase has a general tendency to agglomerate and phase separate in the metal matrix, which is detrimental for the mechanical and chemical properties of the composite. Thus, synthesis of Gr-Al NCs is extremely challenging. This review summarizes the different methods available to synthesize Gr-Al NCs and the resulting properties achieved in these NCs. Understanding the effect of processing parameters on the realized properties opens up the possibility of tailoring the synthesis methods to achieve the desired properties for a given application.

Control design based on dead-zone and leakage adaptive laws for artificial swarm mechanical systems

NASA Astrophysics Data System (ADS)

Zhao, Xiaomin; Chen, Y. H.; Zhao, Han

2017-05-01

We consider the control design of artificial swarm systems with emphasis on four characteristics. First, the agent is made of mechanical components. As a result, the motion of each agent is subject to physical laws that govern mechanical systems. Second, both nonlinearity and uncertainty of the mechanical system are taken into consideration. Third, the ideal agent kinematic performance is treated as a desired d'Alembert constraint. This in turn suggests a creative way of embedding the constraint into the control design. Fourth, two types of adaptive robust control schemes are designed. They both contain leakage and dead-zone. However, one design suggests a trade-off between the amount of leakage and the size of dead-zone, in exchange for a simplified dead-zone structure.

Graphene-Reinforced Aluminum Matrix Composites: A Review of Synthesis Methods and Properties

NASA Astrophysics Data System (ADS)

Chen, Fei; Gupta, Nikhil; Behera, Rakesh K.; Rohatgi, Pradeep K.

2018-03-01

Graphene-reinforced aluminum (Gr-Al) matrix nanocomposites (NCs) have attracted strong interest from both research and industry in high-performance weight-sensitive applications. Due to the vastly different bonding characteristics of the Al matrix (metallic) and graphene (in-plane covalent + inter-plane van der Waals), the graphene phase has a general tendency to agglomerate and phase separate in the metal matrix, which is detrimental for the mechanical and chemical properties of the composite. Thus, synthesis of Gr-Al NCs is extremely challenging. This review summarizes the different methods available to synthesize Gr-Al NCs and the resulting properties achieved in these NCs. Understanding the effect of processing parameters on the realized properties opens up the possibility of tailoring the synthesis methods to achieve the desired properties for a given application.

Circulation and Directional Amplification in the Josephson Parametric Converter

NASA Astrophysics Data System (ADS)

Hatridge, Michael

Nonreciprocal transport and directional amplification of weak microwave signals are fundamental ingredients in performing efficient measurements of quantum states of flying microwave light. This challenge has been partly met, as quantum-limited amplification is now regularly achieved with parametrically-driven, Josephson-junction based superconducting circuits. However, these devices are typically non-directional, requiring external circulators to separate incoming and outgoing signals. Recently this limitation has been overcome by several proposals and experimental realizations of both directional amplifiers and circulators based on interference between several parametric processes in a single device. This new class of multi-parametrically driven devices holds the promise of achieving a variety of desirable characteristics simultaneously- directionality, reduced gain-bandwidth constraints and quantum-limited added noise, and are good candidates for on-chip integration with other superconducting circuits such as qubits.

High Absorptance Coatings for THz Applications

NASA Technical Reports Server (NTRS)

Wollack, Edward J.

2012-01-01

High absorptance materials find application throughout the electromagnetic spectrum as radiation terminations, calibration standards, and glint reduction coatings. Successful use of materials at millimeter through submillimeter wavelengths requires an accurate knowledge and control over their thermal, mechanical, and electromagnetic properties in order to achieve the desired response while minimizing mass and volume. In practice, the achieved blackness is intimately linked to the material properties and geometry. Here, we summarize the characteristics of a variety of tunable artificial dielectric mixtures appropriate for THz applications at room and cryogenic temperatures. Theoretical guidelines for their application will be provided in the context of the effective-medium mean-field-approximation. The performance of these coatings as elements of reflectance standards, radiometric flux calibrators, passive thermal radiators, and stray light suppression baffles for imaging systems will be reviewed.

Impact of wireless communication on multimedia application performance

NASA Astrophysics Data System (ADS)

Brown, Kevin A.

1999-01-01

Multimedia applications and specifically voice and video conferencing tools are widely used in business communications, and are quickly being discovered by the consumer market as well. At the same time, wireless communication services such as PCS voice and cellular data are becoming very popular, leading to the desire to deploy multimedia applications in the wireless environment. Wireless links, however, exhibit several characteristics which are different from traditional wired networks. These include: dynamically changing bandwidth due to mobile host movement in and out of cell where bandwidth is shared, high rates of packet corruption and subsequent loss, and frequent are lengthy disconnections due to obstacles, fading, and movement between cells. In addition, these effects are short-lived and difficult to reproduce, leading to a lack of adequate testing and analysis for applications used in wireless environments.

Characteristics of a broadband dye laser using Pyrromethene and Rhodamine dyes.

PubMed

Tedder, Sarah A; Wheeler, Jeffrey L; Danehy, Paul M

2011-02-20

A broadband dye laser pumped by a frequency-doubled Nd:YAG laser with a full width at half-maximum from 592 to 610 nm was created for the use in a dual-pump broadband coherent anti-Stokes Raman spectroscopy (CARS) system called width increased dual-pump enhanced CARS (WIDECARS). The desired broadband dye laser was generated with a mixture of Pyrromethene dyes as an oscillator gain medium and a spectral selective optic in the oscillator cavity. A mixture of Rhodamine dyes was used in the amplifier dye cell. To create this laser, a study was performed to characterize the spectral behavior of broadband dye lasers created with Rhodamine dyes 590, 610, and 640 and Pyrromethene dyes 597 and 650, as well as mixtures of these dyes.

Diffusion and surface alloying of gradient nanostructured metals

PubMed Central

Lu, Ke

2017-01-01

Gradient nanostructures (GNSs) have been optimized in recent years for desired performance. The diffusion behavior in GNS metals is crucial for understanding the diffusion mechanism and relative characteristics of different interfaces that provide fundamental understanding for advancing the traditional surface alloying processes. In this paper, atomic diffusion, reactive diffusion, and surface alloying processes are reviewed for various metals with a preformed GNS surface layer. We emphasize the promoted atomic diffusion and reactive diffusion in the GNS surface layer that are related to a higher interfacial energy state with respect to those in relaxed coarse-grained samples. Accordingly, different surface alloying processes, such as nitriding and chromizing, have been modified significantly, and some diffusion-related properties have been enhanced. Finally, the perspectives on current research in this field are discussed. PMID:28382244

Feasibility of intercalated graphite railgun armatures

NASA Technical Reports Server (NTRS)

Gaier, James R.; Gooden, Clarence E.; Yashan, Doreen; Naud, Steven

1990-01-01

Graphite intercalation compounds may provide an excellent material for the fabrication of electro-magnetic railgun armatures. As a pulse of power is fed into the armature the intercalate could be excited into the plasma state around the edges of the armature, while the bulk of the current would be carried through the graphite block. Such an armature would have the desirable characteristics of both diffuse plasma armatures and bulk conduction armatures. In addition, the highly anisotropic nature of these materials could enable the electrical and thermal conductivity to be tailored to meet the specific requirements of electromagnetic railgun armatures. Preliminary investigations were performed in an attempt to determine the feasibility of using graphite intercalation compounds as railgun armatures. Issues of fabrication, resistivity, stability, and electrical current spreading are addressed for the case of highly oriented pyrolytic graphite.

Explaining the relationship between insecure attachment and partner abuse: the role of personality characteristics.

PubMed

Buck, Nicole M L; Leenaars, Ellie P E M; Emmelkamp, Paul M G; van Marle, Hjalmar J C

2012-11-01

Studies have found that male batterers are more often insecurely attached as compared with nonbatterers. However, it is still not clear how insecure attachment is related to domestic violence. Many studies compared batterers and nonbatterers regarding pathological personality characteristics that are related to attachment (e.g., dependency, jealousy) and generally found that batterers report more personality characteristics. However, these studies did not investigate which role these characteristics played in the relationship between insecure attachment and battering. The first aim of this study is to test which personality characteristics are good candidates to explain the relationship between insecure attachment and domestic violence. The second aim is to test whether personality characteristics are predictive of battering over and above attachment. Seventy-two mainly court-mandated family-only males who were in group treatment for battering are allocated to a securely and an insecurely attached group and compared with 62 nonbatterers. Using questionnaires, self-esteem, dependency, general distrust, distrust in partner, jealousy, lack of empathy, separation anxiety, desire for control, and impulsivity were assessed. This was the first study that examined distrust, separation anxiety, and desire for control in relation to battering. The results show that the relationship between insecure attachment and domestic violence can be explained by separation anxiety and partner distrust. Moreover, only partner distrust increased the risk for battering over and above insecure attachment. The findings suggest the presence of two subtypes among batterers based on attachment style, which has similarities to the family-only and dysphoric-borderline subtypes suggested by Holtzworth-Munroe and Stuart. Implications of the present findings for therapy are discussed.

Outcomes mapping: a method for dental schools to coordinate learning and assessment based on desired characteristics of a graduate.

PubMed

Schneider, Galen B; Cunningham-Ford, Marsha A; Johnsen, David C; Eckert, Mary Lynn; Mulder, Michael

2014-09-01

This project, utilizing a seldom-used approach to dental education, was designed to define the desired characteristics of a graduating dental student; convert those characteristics to educational outcomes; and use those outcomes to map a dental school's learning and assessment programs, based on outcomes rather than courses and disciplines. A detailed rubric of the outcomes expected of a graduating dental student from this school was developed, building on Commission on Dental Accreditation (CODA) standards and the school's competencies. The presence of each characteristic in the rubric was mapped within and across courses and disciplines. To assess implementation of the rubric, members of two faculty committees and all fourth-year students were asked to use it to rate 1) the importance of each characteristic, 2) the extent to which the school teaches and assesses each, and 3) the extent to which each counts toward overall assessment of competence. All thirty-three faculty members (100 percent) on the committees participated, as did forty-six of the fifty-five students (84 percent). The groups gave high scores to the importance of each characteristic, especially for knowledge and technical competence (then separate categories but merged in the final rubric) and for self-assessment, as well as the extent to which they are being taught and assessed. Respondents most commonly named critical thinking as the area that should be emphasized more. Mapping the curriculum and creating its related database allow the faculty and administration to more systematically coordinate learning and assessment than was possible with a course-based approach.

Optimization of nanoparticles for cardiovascular tissue engineering.

PubMed

Izadifar, Mohammad; Kelly, Michael E; Haddadi, Azita; Chen, Xiongbiao

2015-06-12

Nano-particulate delivery systems have increasingly been playing important roles in cardiovascular tissue engineering. Properties of nanoparticles (e.g. size, polydispersity, loading capacity, zeta potential, morphology) are essential to system functions. Notably, these characteristics are regulated by fabrication variables, but in a complicated manner. This raises a great need to optimize fabrication process variables to ensure the desired nanoparticle characteristics. This paper presents a comprehensive experimental study on this matter, along with a novel method, the so-called Geno-Neural approach, to analyze, predict and optimize fabrication variables for desired nanoparticle characteristics. Specifically, ovalbumin was used as a protein model of growth factors used in cardiovascular tissue regeneration, and six fabrication variables were examined with regard to their influence on the characteristics of nanoparticles made from high molecular weight poly(lactide-co-glycolide). The six-factor five-level central composite rotatable design was applied to the conduction of experiments, and based on the experimental results, a geno-neural model was developed to determine the optimum fabrication conditions. For desired particle sizes of 150, 200, 250 and 300 nm, respectively, the optimum conditions to achieve the low polydispersity index, higher negative zeta potential and higher loading capacity were identified based on the developed geno-neural model and then evaluated experimentally. The experimental results revealed that the polymer and the external aqueous phase concentrations and their interactions with other fabrication variables were the most significant variables to affect the size, polydispersity index, zeta potential, loading capacity and initial burst release of the nanoparticles, while the electron microscopy images of the nanoparticles showed their spherical geometries with no sign of large pores or cracks on their surfaces. The release study revealed that the onset of the third phase of release can be affected by the polymer concentration. Circular dichroism spectroscopy indicated that ovalbumin structural integrity is preserved during the encapsulation process. Findings from this study would greatly contribute to the design of high molecular weight poly(lactide-co-glycolide) nanoparticles for prolonged release patterns in cardiovascular engineering.

Design and development of green roof substrate to improve runoff water quality: plant growth experiments and adsorption.

PubMed

Vijayaraghavan, K; Raja, Franklin D

2014-10-15

Many studies worldwide have investigated the potential benefits achievable by transforming brown roofs of buildings to green roofs. However, little literature examined the runoff quality/sorption ability of green roofs. As the green roof substrate is the main component to alter the quality of runoff, this investigation raises the possibility of using a mixture of low-cost inorganic materials to develop a green roof substrate. The tested materials include exfoliated vermiculite, expanded perlite, crushed brick and sand along with organic component (coco-peat). Detailed physical and chemical analyses revealed that each of these materials possesses different characteristics and hence a mix of these materials was desirable to develop an optimal green roof substrate. Using factorial design, 18 different substrate mixes were prepared and detailed examination indicated that mix-12 exhibited desirable characteristics of green roof substrate with low bulk density (431 kg/m(3)), high water holding capacity (39.4%), air filled porosity (19.5%), and hydraulic conductivity (4570 mm/h). The substrate mix also provided maximum support to Portulaca grandiflora (380% total biomass increment) over one month of growth. To explore the leaching characteristics and sorption capacity of developed green roof substrate, a down-flow packed column arrangement was employed. High conductivity and total dissolved solids along with light metal ions (Na, K, Ca and Mg) were observed in the leachates during initial stages of column operation; however the concentration of ions ceased during the final stages of operation (600 min). Experiments with metal-spiked deionized water revealed that green roof substrate possess high sorption capacity towards various heavy metal ions (Al, Fe, Cr, Cu, Ni, Pb, Zn and Cd). Thus the developed growth substrate possesses desirable characteristics for green roofs along with high sorption capacity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Performance-based planning and programming guidebook.

DOT National Transportation Integrated Search

2013-09-01

"Performance-based planning and programming (PBPP) refers to the application of performance management principles within the planning and programming processes of transportation agencies to achieve desired performance outcomes for the multimodal tran...

Sexual Inhibition is a Vulnerability Factor for Orgasm Problems in Women.

PubMed

Tavares, Inês M; Laan, Ellen T M; Nobre, Pedro J

2018-03-01

The differential role of psychological traits in the etiology and maintenance of female orgasm difficulties is yet to be consistently established. To investigate the contribution of different psychological trait features (personality, sexual inhibition and excitation, and sexual beliefs) to predict female orgasm and to assess the degree to which these dispositional factors moderate the association between sexual activity and orgasm occurrence in a large community sample of Portuguese women. 1,002 women (18-72 years, mean age = 26.27, SD = 8.74) completed questionnaires assessing personality traits (NEO-Five Factor Inventory), sexual inhibition and sexual excitation (Sexual Inhibition/Sexual Excitation Scales-Short Form [SIS/SES]), sexual beliefs (Sexual Dysfunctional Beliefs Questionnaire), sexual behavior (frequency of sexual activities and frequency of orgasm occurrence), and social desirability (Socially Desirable Response Set). Hierarchical multiple regression and moderation analyses were conducted while controlling for the effect of covariates such as social desirability, sociodemographic and medical characteristics, and relationship factors. The main outcome measurement was orgasm frequency as predicted and moderated by personality, SIS/SES dimensions, and sexual beliefs. Results of the hierarchical multiple regression analysis indicated a significant predictive role for sexual inhibition (associated with fear of performance failure [SIS1] and related to the threat of performance consequences) and body image beliefs in female orgasm occurrence. The significant predictive effect of extraversion and of sexual excitation on orgasm frequency ceased to be significant with the insertion of all trait predictors in the final model. Furthermore, SIS1 significantly moderated the relation between sexual activity and orgasm occurrence. Attention should be given to individual factors impairing orgasmic response in women, particularly sexual inhibition processes. The development of clinical strategies to address and regulate them is recommended. Although this study investigated a large community sample, this sample was composed of heterosexual, relatively young women and thus generalization of the present results demands some caution. Social desirability was controlled for in the analyses and questionnaires were not collected face to face, which constitutes a strength of this study because social desirability is lower in self-administered online questionnaires compared with paper-and-pencil questionnaires, particularly for more sensitive sexual issues. SIS1 was found to be a vulnerability factor for female orgasmic difficulties. Future research should test these findings with different samples, particularly clinical samples of women with orgasmic problems, preferably with the use of longitudinal designs. Tavares IM, Laan ETM, Nobre PJ. Sexual Inhibition is a Vulnerability Factor for Orgasm Problems in Women. J Sex Med 2018;15:361-372. Copyright © 2018 International Society for Sexual Medicine. Published by Elsevier Inc. All rights reserved.

Impact of signal scattering and parametric uncertainties on receiver operating characteristics

NASA Astrophysics Data System (ADS)

Wilson, D. Keith; Breton, Daniel J.; Hart, Carl R.; Pettit, Chris L.

2017-05-01

The receiver operating characteristic (ROC curve), which is a plot of the probability of detection as a function of the probability of false alarm, plays a key role in the classical analysis of detector performance. However, meaningful characterization of the ROC curve is challenging when practically important complications such as variations in source emissions, environmental impacts on the signal propagation, uncertainties in the sensor response, and multiple sources of interference are considered. In this paper, a relatively simple but realistic model for scattered signals is employed to explore how parametric uncertainties impact the ROC curve. In particular, we show that parametric uncertainties in the mean signal and noise power substantially raise the tails of the distributions; since receiver operation with a very low probability of false alarm and a high probability of detection is normally desired, these tails lead to severely degraded performance. Because full a priori knowledge of such parametric uncertainties is rarely available in practice, analyses must typically be based on a finite sample of environmental states, which only partially characterize the range of parameter variations. We show how this effect can lead to misleading assessments of system performance. For the cases considered, approximately 64 or more statistically independent samples of the uncertain parameters are needed to accurately predict the probabilities of detection and false alarm. A connection is also described between selection of suitable distributions for the uncertain parameters, and Bayesian adaptive methods for inferring the parameters.

Black Molecular Adsorber Coatings for Spaceflight Applications

NASA Technical Reports Server (NTRS)

Abraham, Nithin Susan; Hasegawa, Mark Makoto; Straka, Sharon A.

2014-01-01

The molecular adsorber coating is a new technology that was developed to mitigate the risk of on-orbit molecular contamination on spaceflight missions. The application of this coating would be ideal near highly sensitive, interior surfaces and instruments that are negatively impacted by outgassed molecules from materials, such as plastics, adhesives, lubricants, epoxies, and other similar compounds. This current, sprayable paint technology is comprised of inorganic white materials made from highly porous zeolite. In addition to good adhesion performance, thermal stability, and adsorptive capability, the molecular adsorber coating offers favorable thermal control characteristics. However, low reflectivity properties, which are typically offered by black thermal control coatings, are desired for some spaceflight applications. For example, black coatings are used on interior surfaces, in particular, on instrument baffles for optical stray light control. Similarly, they are also used within light paths between optical systems, such as telescopes, to absorb light. Recent efforts have been made to transform the white molecular adsorber coating into a black coating with similar adsorptive properties. This result is achieved by optimizing the current formulation with black pigments, while still maintaining its adsorption capability for outgassing control. Different binder to pigment ratios, coating thicknesses, and spray application techniques were explored to develop a black version of the molecular adsorber coating. During the development process, coating performance and adsorption characteristics were studied. The preliminary work performed on black molecular adsorber coatings thus far is very promising. Continued development and testing is necessary for its use on future contamination sensitive spaceflight missions.

Performance Assessment of Suture Type, Water Temperature, and Surgeon Skill in Juvenile Chinook Salmon Surgically Implanted with Acoustic Transmitters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deters, Katherine A.; Brown, Richard S.; Carter, Kathleen M.

2010-05-01

This study assessed performance of seven suture types in subyearling Chinook salmon Oncorhynchus tshawytscha implanted with acoustic microtransmitters. Nonabsorbable (Ethilon) and absorbable (Monocryl) monofilament and nonabsorbable (Nurolon, silk) and absorbable (Vicryl, Vicryl Plus, Vicryl Rapide) braided sutures were used to close incisions in Chinook salmon. Monocryl exhibited greater suture retention than all other suture types 7 d after surgery. Both monofilament suture types were retained better than all braided suture types at 14 d. Incision openness and tag retention did not differ among suture types. Wound inflammation was similar for Ethilon, Monocryl, and Nurolon at 7 d. Wound ulceration wasmore » lower for Ethilon, Monocryl, and Nurolon than for all other suture types at 14 d post-surgery. Fish held in 12°C water had more desirable post-surgery healing characteristics (i.e., higher suture and tag retention and lower incision openness, wound inflammation, and ulceration) at 7 and 14 d after surgery than those held in 17°C water. The effect of surgeon was a significant predictor for all response variables at 7 d. This result emphasizes the importance of including surgeon as a variable in telemetry study analyses when multiple surgeons are used. Monocryl performed better with regard to post-surgery healing characteristics in the study fish. The overall results support the conclusion that Monocryl is the best suture material to close incisions created during surgical implantation of acoustic microtransmitters in subyearling Chinook salmon.« less

Black molecular adsorber coatings for spaceflight applications

NASA Astrophysics Data System (ADS)

Abraham, Nithin S.; Hasegawa, Mark M.; Straka, Sharon A.

2014-09-01

The molecular adsorber coating is a new technology that was developed to mitigate the risk of on-orbit molecular contamination on spaceflight missions. The application of this coating would be ideal near highly sensitive, interior surfaces and instruments that are negatively impacted by outgassed molecules from materials, such as plastics, adhesives, lubricants, epoxies, and other similar compounds. This current, sprayable paint technology is comprised of inorganic white materials made from highly porous zeolite. In addition to good adhesion performance, thermal stability, and adsorptive capability, the molecular adsorber coating offers favorable thermal control characteristics. However, low reflectivity properties, which are typically offered by black thermal control coatings, are desired for some spaceflight applications. For example, black coatings are used on interior surfaces, in particular, on instrument baffles for optical stray light control. Similarly, they are also used within light paths between optical systems, such as telescopes, to absorb light. Recent efforts have been made to transform the white molecular adsorber coating into a black coating with similar adsorptive properties. This result is achieved by optimizing the current formulation with black pigments, while still maintaining its adsorption capability for outgassing control. Different binder to pigment ratios, coating thicknesses, and spray application techniques were explored to develop a black version of the molecular adsorber coating. During the development process, coating performance and adsorption characteristics were studied. The preliminary work performed on black molecular adsorber coatings thus far is very promising. Continued development and testing is necessary for its use on future contamination sensitive spaceflight missions.

Internally resonating lattices for bandgap generation and low-frequency vibration control

NASA Astrophysics Data System (ADS)

Baravelli, Emanuele; Ruzzene, Massimo

2013-12-01

The paper reports on a structural concept for high stiffness and high damping performance. A stiff external frame and an internal resonating lattice are combined in a beam-like assembly which is characterized by high frequency bandgaps and tuned vibration attenuation at low frequencies. The resonating lattice consists of an elastomeric material arranged according to a chiral topology which is designed to resonate at selected frequencies. The concept achieves high damping performance by combining the frequency-selective properties of internally resonating structures, with the energy dissipation characteristics of their constituent material. The flexible ligaments, the circular nodes and the non-central interactions of the chiral topology lead to dynamic deformation patterns which are beneficial to energy dissipation. Furthermore, tuning and grading of the elements of the lattice allows for tailoring of the resonating properties so that vibration attenuation is obtained over desired frequency ranges. Numerical and experimental results demonstrate the tuning flexibility of this concept and suggest its potential application for load-carrying structural members parts of vibration and shock prone systems.

Construction of a genetic map using EST-SSR markers and QTL analysis of major agronomic characters in hexaploid sweet potato (Ipomoea batatas (L.) Lam).

PubMed

Kim, Jin-Hee; Chung, Il Kyung; Kim, Kyung-Min

2017-01-01

The Sweet potato, Ipomoea batatas (L.) Lam, is difficult to study in genetics and genomics because it is a hexaploid. The sweet potato study not have been performed domestically or internationally. In this study was performed to construct genetic map and quantitative trait loci (QTL) analysis. A total of 245 EST-SSR markers were developed, and the map was constructed by using 210 of those markers. The total map length was 1508.1 cM, and the mean distance between markers was 7.2 cM. Fifteen characteristics were investigated for QTLs analysis. According to those, the Four QTLs were identified, and The LOD score was 3.0. Further studies need to develop molecular markers in terms of EST-SSR markers for doing to be capable of efficient breeding. The genetic map created here using EST-SSR markers will facilitate planned breeding of sweet potato cultivars with various desirable traits.

Robust Nonlinear Feedback Control of Aircraft Propulsion Systems

NASA Technical Reports Server (NTRS)

Garrard, William L.; Balas, Gary J.; Litt, Jonathan (Technical Monitor)

2001-01-01

This is the final report on the research performed under NASA Glen grant NASA/NAG-3-1975 concerning feedback control of the Pratt & Whitney (PW) STF 952, a twin spool, mixed flow, after burning turbofan engine. The research focussed on the design of linear and gain-scheduled, multivariable inner-loop controllers for the PW turbofan engine using H-infinity and linear, parameter-varying (LPV) control techniques. The nonlinear turbofan engine simulation was provided by PW within the NASA Rocket Engine Transient Simulator (ROCETS) simulation software environment. ROCETS was used to generate linearized models of the turbofan engine for control design and analysis as well as the simulation environment to evaluate the performance and robustness of the controllers. Comparison between the H-infinity, and LPV controllers are made with the baseline multivariable controller and developed by Pratt & Whitney engineers included in the ROCETS simulation. Simulation results indicate that H-infinity and LPV techniques effectively achieve desired response characteristics with minimal cross coupling between commanded values and are very robust to unmodeled dynamics and sensor noise.

A 380 GHz SIS receiver using Nb/AlO(x)/Nb junctions for a radioastronomical balloon-borne experiment: PRONAOS

NASA Technical Reports Server (NTRS)

Febvre, P.; Feautrier, P.; Robert, C.; Pernot, J. C.; Germont, A.; Hanus, M.; Maoli, R.; Gheudin, M.; Beaudin, G.; Encrenaz, P.

1992-01-01

The superheterodyne detection technique used for the spectrometer instrument of the PRONAOS project will provide a very high spectral resolution (delta nu/nu = 10(exp -6)). The most critical components are those located at the front-end of the receiver: their contribution dominates the total noise of the receiver. Therefore, it is important to perform accurate studies for specific components, such as mixers and multipliers working in the submillimeter wave range. Difficulties in generating enough local oscillator (LO) power at high frequencies make SIS mixers very desirable for operation above 300 GHz. The low LO power requirements and the low noise temperature of these mixers are the primary reason for building an SIS receiver. This paper reports the successful fabrication of small (less than or equal to 1 sq micron) Nb/Al-O(x)/Nb junctions and arrays with excellent I-V characteristics and very good reliability, resulting in a low noise receiver performance measured in the 368/380 GHz frequency range.

Precise, motion-free polarization control in Second Harmonic Generation microscopy using a liquid crystal modulator in the infinity space.

PubMed

Lien, Chi-Hsiang; Tilbury, Karissa; Chen, Shean-Jen; Campagnola, Paul J

2013-01-01

Second Harmonic Generation (SHG) microscopy coupled with polarization analysis has great potential for use in tissue characterization, as molecular and supramolecular structural details can be extracted. Such measurements are difficult to perform quickly and accurately. Here we present a new method that uses a liquid crystal modulator (LCM) located in the infinity space of a SHG laser scanning microscope that allows the generation of any desired linear or circular polarization state. As the device contains no moving parts, polarization can be rotated accurately and faster than by manual or motorized control. The performance in terms of polarization purity was validated using Stokes vector polarimetry, and found to have minimal residual polarization ellipticity. SHG polarization imaging characteristics were validated against well-characterized specimens having cylindrical and/or linear symmetries. The LCM has a small footprint and can be implemented easily in any standard microscope and is cost effective relative to other technologies.

A serious game for learning ultrasound-guided needle placement skills.

PubMed

Chan, Wing-Yin; Qin, Jing; Chui, Yim-Pan; Heng, Pheng-Ann

2012-11-01

Ultrasound-guided needle placement is a key step in a lot of radiological intervention procedures such as biopsy, local anesthesia and fluid drainage. To help training future intervention radiologists, we develop a serious game to teach the skills involved. We introduce novel techniques for realistic simulation and integrate game elements for active and effective learning. This game is designed in the context of needle placement training based on the some essential characteristics of serious games. Training scenarios are interactively generated via a block-based construction scheme. A novel example-based texture synthesis technique is proposed to simulate corresponding ultrasound images. Game levels are defined based on the difficulties of the generated scenarios. Interactive recommendation of desirable insertion paths is provided during the training as an adaptation mechanism. We also develop a fast physics-based approach to reproduce the shadowing effect of needles in ultrasound images. Game elements such as time-attack tasks, hints and performance evaluation tools are also integrated in our system. Extensive experiments are performed to validate its feasibility for training.

Layered conductive polymer on nylon membrane templates for high performance, thin-film supercapacitor electrodes

NASA Astrophysics Data System (ADS)

Shi, HaoTian Harvey; Naguib, Hani E.

2016-04-01

Flexible Thin-film Electrochemical Capacitors (ECs) are emerging technology that plays an important role as energy supply for various electronics system for both present era and the future. Intrinsically conductive polymers (ICPs) are promising pseudo-capacitive materials as they feature both good electrical conductivity and high specific capacitance. This study focuses on the construction and characterization of ultra-high surface area porous electrodes based on coating of nano-sized conductive polymer materials on nylon membrane templates. Herein, a novel nano-engineered electrode material based on nylon membranes was presented, which allows the creation of super-capacitor devices that is capable of delivering competitive performance, while maintaining desirable mechanical characteristics. With the formation of a highly conductive network with the polyaniline nano-layer, the electrical conductivity was also increased dramatically to facilitate the charge transfer process. Cyclic voltammetry and specific capacitance results showed promising application of this type of composite materials for future smart textile applications.

Multi-Axis Force Sensor for Human-Robot Interaction Sensing in a Rehabilitation Robotic Device.

PubMed

Grosu, Victor; Grosu, Svetlana; Vanderborght, Bram; Lefeber, Dirk; Rodriguez-Guerrero, Carlos

2017-06-05

Human-robot interaction sensing is a compulsory feature in modern robotic systems where direct contact or close collaboration is desired. Rehabilitation and assistive robotics are fields where interaction forces are required for both safety and increased control performance of the device with a more comfortable experience for the user. In order to provide an efficient interaction feedback between the user and rehabilitation device, high performance sensing units are demanded. This work introduces a novel design of a multi-axis force sensor dedicated for measuring pelvis interaction forces in a rehabilitation exoskeleton device. The sensor is conceived such that it has different sensitivity characteristics for the three axes of interest having also movable parts in order to allow free rotations and limit crosstalk errors. Integrated sensor electronics make it easy to acquire and process data for a real-time distributed system architecture. Two of the developed sensors are integrated and tested in a complex gait rehabilitation device for safe and compliant control.

Animal breeding strategies can improve meat quality attributes within entire populations.

PubMed

Berry, D P; Conroy, S; Pabiou, T; Cromie, A R

2017-10-01

The contribution of animal breeding to changes in animal performance is well documented across a range of species. Once genetic variation in a trait exists, then breeding to improve the characteristics of that trait is possible, if so desired. Considerable genetic variation exists in a range of meat quality attributes across a range of species. The genetic variation that exists for meat quality is as large as observed for most performance traits; thus, within a well-structured breeding program, rapid genetic gain for meat quality could be possible. The rate of genetic gain can be augmented through the integration of DNA-based technologies into the breeding program; such DNA-based technologies should, however, be based on thousands of DNA markers dispersed across the entire genome. Genetic and genomic technologies can also have beneficial impact outside the farm gate as a tool to segregate carcasses or meat cuts based on expected meat quality features. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tripropellant engine study

NASA Technical Reports Server (NTRS)

Wheeler, D. B.

1977-01-01

Work conducted was devoted to three main tasks. Thermochemical equilibrium performance data were assembled to establish the expected performance calculations of the mode 1 engine propellant combinations and thermodynamic and transport data for the products of combustion. Turbine drive gas characteristics were also established. Thrust chamber and nozzle cooling studies were devoted to the evaluation of H2, C3H8, CH4, and RP-1 as coolants in the existing SSME cooling circuit geometry. It was found that all these candidate coolants are feasible without limiting the desired operating conditions with the exception of RP-1, which would limit the maximum P(c) to 2000 psia. RP-1 could be used, however, to cool the nozzle only without imposing the chamber pressure limit. A total of 15 candidate engine system cycles were selected and a preliminary engine system balance was conducted for 12 of these systems to establish component operating flowrates, pressures and temperatures. It was found that the staged combustion cycles employing fuel rich LOX/hydrocarbon turbine drive gases are power limited.

Lunar surface base propulsion system study, volume 1

NASA Technical Reports Server (NTRS)

1987-01-01

The efficiency, capability, and evolution of a lunar base will be largely dependent on the transportation system that supports it. Beyond Space Station in low Earth orbit (LEO), a Lunar-derived propellant supply could provide the most important resource for the transportation infrastructure. The key to an efficient Lunar base propulsion system is the degree of Lunar self-sufficiency (from Earth supply) and reasonable propulsion system performance. Lunar surface propellant production requirements must be accounted in the measurement of efficiency of the entire space transportation system. Of all chemical propellant/propulsion systems considered, hydrogen/oxygen (H/O) OTVs appear most desirable, while both H/O and aluminum/oxygen propulsion systems may be considered for the lander. Aluminized-hydrogen/oxygen and Silane/oxygen propulsion systems are also promising candidates. Lunar propellant availability and processing techniques, chemical propulsion/vehicle design characteristics, and the associated performance of the total transportation infrastructure are reviewed, conceptual propulsion system designs and vehicle/basing concepts, and technology requirements are assessed in context of a Lunar Base mission scenario.

What separates outstanding from average leaders? A study identifies leadership competencies and implications for professional development.

PubMed

Nygren, D J; Ukeritis, M D

1992-11-01

As the healthcare crisis mounts, healthcare organizations must be managed by especially competent leaders. It is important for executives to assess and develop the competencies necessary to become "outstanding" leaders. In our study of leadership competencies among leaders of religious orders, we found that outstanding and average leaders appear to share characteristics such as the ability to articulate their group's mission, the ability to act efficiently, and the tendency to avoid impulsive behavior or excessive emotional expression. Outstanding leaders, however, differed from average leaders in seemingly small but significant ways. For instance, nearly three times as often as average leaders, outstanding leaders expressed a desire to perform tasks well--or better than they had been performed in the past. The study also assessed how members of religious orders perceived their leaders. In general, they tended to rate leaders of their religious institutes as transformational leaders--leaders who welcomed doing things in a new way and inspiring their own staffs to search out new ways to provide services.

Thermal and optical design analyses, optimizations, and experimental verification for a novel glare-free LED lamp for household applications.

PubMed

Khan, M Nisa

2015-07-20

Light-emitting diode (LED) technologies are undergoing very fast developments to enable household lamp products with improved energy efficiency and lighting properties at lower cost. Although many LED replacement lamps are claimed to provide similar or better lighting quality at lower electrical wattage compared with general-purpose incumbent lamps, certain lighting characteristics important to human vision are neglected in this comparison, which include glare-free illumination and omnidirectional or sufficiently broad light distribution with adequate homogeneity. In this paper, we comprehensively investigate the thermal and lighting performance and trade-offs for several commercial LED replacement lamps for the most popular Edison incandescent bulb. We present simulations and analyses for thermal and optical performance trade-offs for various LED lamps at the chip and module granularity levels. In addition, we present a novel, glare-free, and production-friendly LED lamp design optimized to produce very desirable light distribution properties as demonstrated by our simulation results, some of which are verified by experiments.

Precise, motion-free polarization control in Second Harmonic Generation microscopy using a liquid crystal modulator in the infinity space

PubMed Central

Lien, Chi-Hsiang; Tilbury, Karissa; Chen, Shean-Jen; Campagnola, Paul J.

2013-01-01

Second Harmonic Generation (SHG) microscopy coupled with polarization analysis has great potential for use in tissue characterization, as molecular and supramolecular structural details can be extracted. Such measurements are difficult to perform quickly and accurately. Here we present a new method that uses a liquid crystal modulator (LCM) located in the infinity space of a SHG laser scanning microscope that allows the generation of any desired linear or circular polarization state. As the device contains no moving parts, polarization can be rotated accurately and faster than by manual or motorized control. The performance in terms of polarization purity was validated using Stokes vector polarimetry, and found to have minimal residual polarization ellipticity. SHG polarization imaging characteristics were validated against well-characterized specimens having cylindrical and/or linear symmetries. The LCM has a small footprint and can be implemented easily in any standard microscope and is cost effective relative to other technologies. PMID:24156059

GENERALIZED DIGITAL CONTOURING PROGRAM

NASA Technical Reports Server (NTRS)

Jones, R. L.

1994-01-01

This is a digital computer contouring program developed by combining desirable characteristics from several existing contouring programs. It can easily be adapted to many different research requirements. The overlaid structure of the program permits desired modifications to be made with ease. The contouring program performs both the task of generating a depth matrix from either randomly or regularly spaced surface heights and the task of contouring the data. Each element of the depth matrix is computed as a weighted mean of heights predicted at an element by planes tangent to the surface at neighboring control points. Each contour line is determined by its intercepts with the sides of geometrical figures formed by connecting the various elements of the depth matrix with straight lines. Although contour charts are usually thought of as being two-dimensional pictorial representations of topographic formations of land masses, they can also be useful in portraying data which are obtained during the course of research in various scientific disciplines and which would ordinarily be tabulated. Any set of data which can be referenced to a two-dimensional coordinate system can be graphically represented by this program. This program is written in FORTRAN IV and ASSEMBLER for batch execution and has been implemented on the CDC 6000 Series. This program was developed in 1971.

Dispersions of Aramid Nanofibers: A New Nanoscale Building Block

PubMed Central

Yang, Ming; Cao, Keqin; Sui, Lang; Qi, Ying; Zhu, Jian; Waas, Anthony; Arruda, Ellen M.; Kieffer, John; Thouless, M. D.; Kotov, Nicholas A.

2011-01-01

Stable dispersions of nanofibers are virtually unknown for synthetic polymers. They can complement analogous dispersions of inorganic components, such as nanoparticles, nanowires, nanosheets, etc as a fundamental component of a toolset for design of nanostructures and metamaterials via numerous solvent-based processing methods. As such, strong flexible polymeric nanofibers are very desirable for the effective utilization within composites of nanoscale inorganic components such as nanowires, carbon nanotubes, graphene, and others. Here stable dispersions of uniform high-aspect-ratio aramid nanofibers (ANFs) with diameters between 3 and 30 nm and up to 10 μm in length were successfully obtained. Unlike the traditional approaches based on polymerization of monomers, they are made by controlled dissolution of standard macroscale form of the aramid polymer, i.e. well known Kevlar threads, and revealed distinct morphological features similar to carbon nanotubes. ANFs are successfully processed into films using layer-by-layer (LBL) assembly as one of the potential methods of preparation of composites from ANFs. The resultant films are transparent and highly temperature resilient. They also display enhanced mechanical characteristics making ANF films highly desirable as protective coatings, ultrastrong membranes, as well as building blocks of other high performance materials in place of or in combination with carbon nanotubes. PMID:21800822

Performance characteristics of single effect lithium bromide/ water absorption chiller for small data centers

NASA Astrophysics Data System (ADS)

Mysore, Abhishek Arun Babu

A medium data center consists of servers performing operations such as file sharing, collaboration and email. There are a large number of small and medium data centers across the world which consume more energy and are less efficient when compared to large data center facilities of companies such as GOOGLE, APPLE and FACEBOOK. Such companies are making their data center facilities more environmental friendly by employing renewable energy solutions such as wind and solar to power the data center or in data center cooling. This not only reduces the carbon footprint significantly but also decreases the costs incurred over a period of time. Cooling of data center play a vital role in proper functioning of the servers. It is found that cooling consumes about 50% of the total power consumed by the data center. Traditional method of cooling includes the use of mechanical compression chillers which consume lot of power and is not desirable. In order to eliminate the use of mechanical compressor chillers renewable energy resources such as solar and wind should be employed. One such technology is solar thermal cooling by means of absorption chiller which is powered by solar energy. The absorption chiller unit can be coupled with either flat plate or evacuated tube collectors in order to achieve the required inlet temperature for the generator of the absorption chiller unit. In this study a modular data center is considered having a cooling load requirement of 23kw. The performance characteristics of a single stage Lithium Bromide/ water refrigeration is presented in this study considering the cooling load of 23kw. Performance characteristics of each of the 4 heat exchangers within the unit is discussed which helps in customizing the unit according to the users' specific needs. This analysis helps in studying the importance of different properties such as the effect of inlet temperatures of hot water for generator, inlet temperatures of cooling water for absorber and condenser and outlet chilled water temperatures of the evaporator.

Power of the desired self: Influence of induced perceptions of the self on reasoning.

PubMed

Augustinova, Maria; Collange, Julie; Sanitioso, Rasyid Bo; Musca, Serban C

2011-12-01

This research shows that the motivation to posses a desired characteristic (or to avoid an undesired one) results in self-perceptions that guide people's use of base rate in the Lawyer-Engineer problem (Kahneman & Tversky, 1973). In four studies, participants induced to believe (or recall, Exp. 2) that a rational cognitive style is success-conducive (or an intuitive cognitive style failure-conducive) subsequently viewed themselves as more rational and relied more on base rate in their probability estimates than those induced to believe that a rational cognitive style is failure-conducive (or an intuitive cognitive style success-conducive). These findings show that the desired self had an influence on reasoning in the self-unrelated lawyer-engineer task, since the use of base rates was mediated by changes in participants' perceptions of their own rationality. These findings therefore show that the desired self, through the working self-concept that it entails, constitutes another factor influencing people's use of distinct modes of reasoning. Copyright © 2011 Elsevier B.V. All rights reserved.

The Influence of Modulated Signal Risetime in Flight Electronics Radiated Immunity Testing with a Mode-Stirred Chamber

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Nguyen, Truong X.; Scearce, Stephen A.

2000-01-01

For electromagnetic immunity testing of an electronic system, it is desirable to demonstrate its functional integrity when exposed to the full range and intensity of environmental electromagnetic threats that may be encountered over its operational life. As part of this, it is necessary to show proper system operation when exposed to representative threat signal modulations. Modulated signal transition time is easily overlooked, but can be highly significant to system susceptibility. Radiated electromagnetic field immunity testing is increasingly being performed in Mode Stirred Chambers. Because the peak field vs. time relationship is affected by the operation of a reverberating room, it is important to understand how the room may influence any input signal modulation characteristics. This paper will provide insight into the field intensity vs. time relationship within the test environment of a mode stirred chamber. An understanding of this relationship is important to EMC engineers in determining what input signal modulation characteristics will be transferred to the equipment under test. References will be given for the development of this topic, and experimental data will be presented

The Challenges Facing Science Data Archiving on Current Mass Storage Systems

NASA Technical Reports Server (NTRS)

Peavey, Bernard; Behnke, Jeanne (Editor)

1996-01-01

This paper discusses the desired characteristics of a tape-based petabyte science data archive and retrieval system required to store and distribute several terabytes (TB) of data per day over an extended period of time, probably more than 115 years, in support of programs such as the Earth Observing System Data and Information System (EOSDIS). These characteristics take into consideration not only cost effective and affordable storage capacity, but also rapid access to selected files, and reading rates that are needed to satisfy thousands of retrieval transactions per day. It seems that where rapid random access to files is not crucial, the tape medium, magnetic or optical, continues to offer cost effective data storage and retrieval solutions, and is likely to do so for many years to come. However, in environments like EOS these tape based archive solutions provide less than full user satisfaction. Therefore, the objective of this paper is to describe the performance and operational enhancements that need to be made to the current tape based archival systems in order to achieve greater acceptance by the EOS and similar user communities.

Feasibility study on conducting overflight measurements of shaped sonic boom signatures using the Firebee BQM-34E RPV

NASA Technical Reports Server (NTRS)

Maglieri, Domenic J.; Sothcott, Victor E.; Keefer, Thomas N., Jr.

1993-01-01

A study was performed to determine the feasibility of establishing if a 'shaped' sonic boom signature, experimentally shown in wind tunnel models out to about 10 body lengths, will persist out to representative flight conditions of 200 to 300 body lengths. The study focuses on the use of a relatively large supersonic remotely-piloted and recoverable vehicle. Other simulation methods that may accomplish the objective are also addressed and include the use of nonrecoverable target drones, missiles, full-scale drones, very large wind tunnels, ballistic facilities, whirling-arm techniques, rocket sled tracks, and airplane nose probes. In addition, this report will also present a background on the origin of the feasibility study including a brief review of the equivalent body concept, a listing of the basic sonic boom signature characteristics and requirements, identification of candidate vehicles in terms of desirable features/availability, and vehicle characteristics including geometries, area distributions, and resulting sonic boom signatures. A program is developed that includes wind tunnel sonic boom and force models and tests for both a basic and modified vehicles and full-scale flight tests.

Selective excitation of window and buffer layers in chalcopyrite devices and modules

DOE PAGES

Glynn, Stephen; Repins, Ingrid L.; Burst, James M.; ...

2018-02-02

Window and buffer layers in chalcopyrite devices are well known to affect junctions, conduction, and photo-absorption properties of the device. Some of these layers, particularly 'buffers,' which are deposited directly on top of the absorber, exhibit metastable effects upon exposure to light. Thus, to understand device performance and/or metastability, it is sometimes desirable to selectively excite different layers in the device stack. Absorption characteristics of various window and buffer layers used in chalcopyrite devices are measured. These characteristics are compared with emission spectra of common and available light sources that might be used to optically excite such layers. Effects ofmore » the window and buffer absorption on device quantum efficiency and metastability are discussed. For the case of bath-deposited Zn(O,S) buffers, we conclude that this layer is not optically excited in research devices or modules. Furthermore, this provides a complimentary mechanism to the chemical differences that may cause long time constants (compared to devices with CdS buffers) associated with reaching a stable 'light-soaked' state.« less

Head flying characteristics in heat assisted magnetic recording considering various nanoscale heat transfer models

NASA Astrophysics Data System (ADS)

Hu, Yueqiang; Wu, Haoyu; Meng, Yonggang; Wang, Yu; Bogy, David

2018-01-01

The thermal issues in heat-assisted magnetic recording (HAMR) technology have drawn much attention in the recent literature. In this paper, the head flying characteristics and thermal performance of a HAMR system during the touch-down process considering different nanoscale heat transfer models across the head-disk interface are numerically studied. An optical-thermal-mechanical coupled model is first described. The coupling efficiency of the near field transducer is found to be dependent on the head disk clearance. The shortcomings of a constant disk-temperature model are investigated, which reveals the importance of considering the disk temperature as a variable. A study of the head flying on the disk is carried out using an air conduction model and additional near-field heat transfer models. It is shown that when the head disk interface is filled with a solid material caused by the laser-induced accumulation, the heat transfer coefficient can become unexpectedly large and the head's temperature can rise beyond desirable levels. Finally, the additional head protrusion due to the laser heating is investigated.

Selective excitation of window and buffer layers in chalcopyrite devices and modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glynn, Stephen; Repins, Ingrid L.; Burst, James M.

Window and buffer layers in chalcopyrite devices are well known to affect junctions, conduction, and photo-absorption properties of the device. Some of these layers, particularly 'buffers,' which are deposited directly on top of the absorber, exhibit metastable effects upon exposure to light. Thus, to understand device performance and/or metastability, it is sometimes desirable to selectively excite different layers in the device stack. Absorption characteristics of various window and buffer layers used in chalcopyrite devices are measured. These characteristics are compared with emission spectra of common and available light sources that might be used to optically excite such layers. Effects ofmore » the window and buffer absorption on device quantum efficiency and metastability are discussed. For the case of bath-deposited Zn(O,S) buffers, we conclude that this layer is not optically excited in research devices or modules. Furthermore, this provides a complimentary mechanism to the chemical differences that may cause long time constants (compared to devices with CdS buffers) associated with reaching a stable 'light-soaked' state.« less

Aerocapture Performance Analysis for a Neptune-Triton Exploration Mission

NASA Technical Reports Server (NTRS)

Starr, Brett R.; Westhelle, Carlos H.; Masciarelli, James P.

2004-01-01

A systems analysis has been conducted for a Neptune-Triton Exploration Mission in which aerocapture is used to capture a spacecraft at Neptune. Aerocapture uses aerodynamic drag instead of propulsion to decelerate from the interplanetary approach trajectory to a captured orbit during a single pass through the atmosphere. After capture, propulsion is used to move the spacecraft from the initial captured orbit to the desired science orbit. A preliminary assessment identified that a spacecraft with a lift to drag ratio of 0.8 was required for aerocapture. Performance analyses of the 0.8 L/D vehicle were performed using a high fidelity flight simulation within a Monte Carlo executive to determine mission success statistics. The simulation was the Program to Optimize Simulated Trajectories (POST) modified to include Neptune specific atmospheric and planet models, spacecraft aerodynamic characteristics, and interplanetary trajectory models. To these were added autonomous guidance and pseudo flight controller models. The Monte Carlo analyses incorporated approach trajectory delivery errors, aerodynamic characteristics uncertainties, and atmospheric density variations. Monte Carlo analyses were performed for a reference set of uncertainties and sets of uncertainties modified to produce increased and reduced atmospheric variability. For the reference uncertainties, the 0.8 L/D flatbottom ellipsled vehicle achieves 100% successful capture and has a 99.87 probability of attaining the science orbit with a 360 m/s V budget for apoapsis and periapsis adjustment. Monte Carlo analyses were also performed for a guidance system that modulates both bank angle and angle of attack with the reference set of uncertainties. An alpha and bank modulation guidance system reduces the 99.87 percentile DELTA V 173 m/s (48%) to 187 m/s for the reference set of uncertainties.

Endoscopic intestinal bypass creation by using self-assembling magnets in a porcine model.

PubMed

Ryou, Marvin; Agoston, A Tony; Thompson, Christopher C

2016-04-01

A purely endoluminal method of GI bypass would be desirable for the treatment of obstruction, obesity, or metabolic syndrome. We have developed a technology based on miniature self-assembling magnets that create large-caliber anastomoses (Incisionless Anastomosis System [IAS]). The aim of this study was to evaluate procedural characteristics of IAS deployment and long-term anastomotic integrity and patency. We performed a 3-month survival study of Yorkshire pigs (5 interventions, 3 controls). Intervention pigs underwent simultaneous enteroscopy/colonoscopy performed with the animals under intravenous sedation. The IAS magnets were deployed and coupled with reciprocal magnets under fluoroscopy. Every 3 to 6 days pigs underwent endoscopy until jejunocolonic anastomosis (dual-path bypass) creation and magnet expulsion. Necropsies and histological evaluation were performed. The primary endpoints were technical success; secondary endpoints of anastomosis integrity, patency, and histological characteristics were weight trends. Under intravenous sedation, endoscopic bypass creation by using IAS magnets was successfully performed in 5 of 5 pigs (100%). Given porcine anatomy, the easiest dual-path bypass to create was between the proximal jejunum and colon. The mean procedure time was 14.7 minutes. Patent, leak-free anastomoses formed by day 4. All IAS magnets were expelled by day 12. All anastomoses were fully patent at 3 months with a mean diameter of 3.5 cm. The mean 3-month weight was 45 kg in bypass pigs and 78 kg in controls (P = .01). At necropsy, adhesions were absent. Histology showed full re-epithelialization across the anastomosis without fibrosis or inflammation. Large-caliber, leak-free, foreign body-free endoscopic intestinal bypass by using IAS magnets can be safely and rapidly performed in the porcine by model using only intravenous sedation. Copyright © 2016 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Densely-packed graphene/conducting polymer nanoparticle papers for high-volumetric-performance flexible all-solid-state supercapacitors

NASA Astrophysics Data System (ADS)

Yang, Chao; Zhang, Liling; Hu, Nantao; Yang, Zhi; Wei, Hao; Xu, Zhichuan J.; Wang, Yanyan; Zhang, Yafei

2016-08-01

Graphene-based all-solid-state supercapacitors (ASSSCs) are one of the most ideal candidates for high-performance flexible power sources. The achievement of high volumetric energy density is highly desired for practical application of this type of ASSSCs. Here, we present a facile method to boost volumetric performances of graphene-based flexible ASSSCs through incorporation of ultrafine polyaniline-poly(4-styrenesulfonate) (PANI-PSS) nanoparticles in reduced graphene oxide (rGO) papers. A compact structure is obtained via intimate contact and π-π interaction between PANI-PSS nanoparticles and rGO sheets. The hybrid paper electrode with the film thickness of 13.5 μm, shows an extremely high volumetric specific capacitance of 272 F/cm3 (0.37 A/cm3 in a three-electrode cell). The assembled ASSSCs show a large volumetric specific capacitance of 217 F/cm3 (0.37 A/cm3 in a two-electrode cell), high volumetric energy and power density, excellent capacitance stability, small leakage current as well as low self-discharge characteristics, revealing the usefulness of this robust hybrid paper for high-performance flexible energy storage devices.

Employee characteristics and health belief variables related to smoking cessation engagement attitudes.

PubMed

Street, Tamara D; Lacey, Sarah J

2018-05-01

Workplace smoking cessation programs can effectively assist employees to quit smoking. However, little is known about employees' attitudes towards engagement in workplace smoking cessation programs. This study aimed to address the limited understanding of the interaction between employee characteristics and their health beliefs toward engaging in a workplace smoking cessation program. Self-report data was collected from 897 employees of a mining company operating in two remote towns in Australia. The majority of participants were male (73%), the mean age was 36.9 years (SD = 11.5). Chi square tests of independence were used to analyze relationships between employee characteristics and smoking cessation engagement attitudes. Engagement attitudes included: A desire to cease smoking; desire for assistance with the smoking cessation process; and intention to participate in a workplace smoking intervention. The findings from this study indicated that attitudes towards engagement in smoking cessation programs varied for mining employees according to gender, age, perceived severity, perceived self-efficacy, and stage of readiness to change. These findings provide insights that health promotion practitioners may apply to inform the design and marketing of effective workplace smoking cessation programs for similar employees.

Improvement of multiprocessing performance by using optical centralized shared bus

NASA Astrophysics Data System (ADS)

Han, Xuliang; Chen, Ray T.

2004-06-01

With the ever-increasing need to solve larger and more complex problems, multiprocessing is attracting more and more research efforts. One of the challenges facing the multiprocessor designers is to fulfill in an effective manner the communications among the processes running in parallel on multiple multiprocessors. The conventional electrical backplane bus provides narrow bandwidth as restricted by the physical limitations of electrical interconnects. In the electrical domain, in order to operate at high frequency, the backplane topology has been changed from the simple shared bus to the complicated switched medium. However, the switched medium is an indirect network. It cannot support multicast/broadcast as effectively as the shared bus. Besides the additional latency of going through the intermediate switching nodes, signal routing introduces substantial delay and considerable system complexity. Alternatively, optics has been well known for its interconnect capability. Therefore, it has become imperative to investigate how to improve multiprocessing performance by utilizing optical interconnects. From the implementation standpoint, the existing optical technologies still cannot fulfill the intelligent functions that a switch fabric should provide as effectively as their electronic counterparts. Thus, an innovative optical technology that can provide sufficient bandwidth capacity, while at the same time, retaining the essential merits of the shared bus topology, is highly desirable for the multiprocessing performance improvement. In this paper, the optical centralized shared bus is proposed for use in the multiprocessing systems. This novel optical interconnect architecture not only utilizes the beneficial characteristics of optics, but also retains the desirable properties of the shared bus topology. Meanwhile, from the architecture standpoint, it fits well in the centralized shared-memory multiprocessing scheme. Therefore, a smooth migration with substantial multiprocessing performance improvement is expected. To prove the technical feasibility from the architecture standpoint, a conceptual emulation of the centralized shared-memory multiprocessing scheme is demonstrated on a generic PCI subsystem with an optical centralized shared bus.

Family size preferences and contraception in Syria.

PubMed

Immerwahr, G; Maier, A

1986-06-01

Data from the Syria Fertility Survey, a part of the World Fertility Survey, are used to ascertain the relation of background characteristics of Syrian women to their preferred number of children, their desire to stop child-bearing and the extent to which this desire is implemented by the use of contraception. Data show Syria in total to have very high fertility, almost the highest in the world. Syrian women state high fertility desires, a high preference for sons and a low use of contraception despite widespread contraceptive knowledge. While they also show in the urban sector a recent fertility decline and a desired family size well below that of the rural sector, that desired family size is at least double replacement level fertility, even among younger urban women. If one were to look at this picture as static, the outlook for an early substantial fertility reduction would at 1st seem quite disappointing. However, there is some prospect of substantial change, not only in the urban sector butalso in the likelihood that this recent urban trend will soon be felt in the rural sector as well. The spread of education and other forms of modernization suggest the likelihood of a steady decline of fertility in the coming decades in the country as a whole.

Benefits of incorporating spatial organisation of catchments for a semi-distributed hydrological model

NASA Astrophysics Data System (ADS)

Schumann, Andreas; Oppel, Henning

2017-04-01

To represent the hydrological behaviour of catchments a model should reproduce/reflect the hydrologically most relevant catchment characteristics. These are heterogeneously distributed within a watershed but often interrelated and subject of a certain spatial organisation. Since common models are mostly based on fundamental assumptions about hydrological processes, the reduction of variance of catchment properties as well as the incorporation of the spatial organisation of the catchment is desirable. We have developed a method that combines the idea of the width-function used for determination of the geomorphologic unit hydrograph with information about soil or topography. With this method we are able to assess the spatial organisation of selected catchment characteristics. An algorithm was developed that structures a watershed into sub-basins and other spatial units to minimise its heterogeneity. The outcomes of this algorithm are used for the spatial setup of a semi-distributed model. Since the spatial organisation of a catchment is not bound to a single characteristic, we have to embed information of multiple catchment properties. For this purpose we applied a fuzzy-based method to combine the spatial setup for multiple single characteristics into a union, optimal spatial differentiation. Utilizing this method, we are able to propose a spatial structure for a semi-distributed hydrological model, comprising the definition of sub-basins and a zonal classification within each sub-basin. Besides the improved spatial structuring, the performed analysis ameliorates modelling in another way. The spatial variability of catchment characteristics, which is considered by a minimum of heterogeneity in the zones, can be considered in a parameter constrained calibration scheme in a case study both options were used to explore the benefits of incorporating the spatial organisation and derived parameter constraints for the parametrisation of a HBV-96 model. We use two benchmark model setups (lumped and semi-distributed by common approaches) to address the benefits for different time and spatial scales. Moreover, the benefits for calibration effort, model performance in validation periods and process extrapolation are shown.

Guidelines for Selecting Microphones for Human Voice Production Research

ERIC Educational Resources Information Center

Svec, Jan G.; Granqvist, Svante

2010-01-01

Purpose: This tutorial addresses fundamental characteristics of microphones (frequency response, frequency range, dynamic range, and directionality), which are important for accurate measurements of voice and speech. Method: Technical and voice literature was reviewed and analyzed. The following recommendations on desirable microphone…

Survey of International Trade/Economics Textbooks.

ERIC Educational Resources Information Center

Lucier, Richard L.

1992-01-01

Reviews 14 international economics textbooks to help instructors with selection. Includes organization and structure, topics covered, and characteristics of the texts. Suggests considerations such as course length, level of abstraction desired, opinion of numerically based graphical analysis, extensiveness of examples and applications, and whether…

Fiber Optic Communications Technology. A Status Report.

ERIC Educational Resources Information Center

Hull, Joseph A.

Fiber optic communications (communications over very pure glass transmission channels of diameter comparable to a human hair) is an emerging technology which promises most improvements in communications capacity at reasonable cost. The fiber transmission system offers many desirable characteristics representing improvements over conventional…

Method and apparatus for separating material

DOEpatents

Oder, Robin R.; Jamison, Russell E.

2004-11-23

An apparatus for sorting particles composed of a mixture of particles with differing physical and chemical characteristics. The apparatus includes a comminutor or a pulverizer for reducing the size of the particles. The apparatus includes a mechanism for separating undesired material from desired material.

Skin quality in red potatoes

USDA-ARS?s Scientific Manuscript database

Attractive appearance is a highly desirable characteristic of fresh market red-skinned potatoes. The ideal red potato has a rich, uniform, deep red color. Color fading, netting, browning, and discoloration caused by skinning and disease decrease marketability and may reduce profits to growers and pa...

The Impact of Social Desirability on Organizational Behavior Research Results: An Empirical Investigation of Alternative Models,

DTIC Science & Technology

1982-02-01

TANAAD S t(AB A , THE IMPACT OF SOCIAL DESIRABILITY ON ORGANIZATIONAL BEHAVIOR RESEARCH RESULTS: AN EMPIRICAL INVESTIGATION OF ALTERNATIVE MODELS Daniel C...Investigation of Alternative Models 4- PERFORMING G. RE.PORTNUMBER 7. AU ?wnOPe) a. CONTRACf OR GR1ANT NUBAe Daniel C. Ganster, Harry W. Hennessey, and Fred...Fred Luthans University of Nebraska-Lincoln ABSTRACT Three conceptual and statistical models are developed for the effects of social desirability (SD

To t-Test or Not to t-Test? A p-Values-Based Point of View in the Receiver Operating Characteristic Curve Framework.

PubMed

Vexler, Albert; Yu, Jihnhee

2018-04-13

A common statistical doctrine supported by many introductory courses and textbooks is that t-test type procedures based on normally distributed data points are anticipated to provide a standard in decision-making. In order to motivate scholars to examine this convention, we introduce a simple approach based on graphical tools of receiver operating characteristic (ROC) curve analysis, a well-established biostatistical methodology. In this context, we propose employing a p-values-based method, taking into account the stochastic nature of p-values. We focus on the modern statistical literature to address the expected p-value (EPV) as a measure of the performance of decision-making rules. During the course of our study, we extend the EPV concept to be considered in terms of the ROC curve technique. This provides expressive evaluations and visualizations of a wide spectrum of testing mechanisms' properties. We show that the conventional power characterization of tests is a partial aspect of the presented EPV/ROC technique. We desire that this explanation of the EPV/ROC approach convinces researchers of the usefulness of the EPV/ROC approach for depicting different characteristics of decision-making procedures, in light of the growing interest regarding correct p-values-based applications.