Pre-Processes for Urban Areas Detection in SAR Images

NASA Astrophysics Data System (ADS)

Altay Açar, S.; Bayır, Ş.

2017-11-01

In this study, pre-processes for urban areas detection in synthetic aperture radar (SAR) images are examined. These pre-processes are image smoothing, thresholding and white coloured regions determination. Image smoothing is carried out to remove noises then thresholding is applied to obtain binary image. Finally, candidate urban areas are detected by using white coloured regions determination. All pre-processes are applied by utilizing the developed software. Two different SAR images which are acquired by TerraSAR-X are used in experimental study. Obtained results are shown visually.

Processing and fractional utilization of lignocellulosic substrates by "pure" and "natural and defined mixed" culture C.TM1, C.SA IV and rumen mixed culture consortia CD.

PubMed

Sankar, M; Chandra, T S

2003-01-01

A detailed analysis was made of chemical fractions of common agro-residues before and after pretreatment (alkali and hydrogen peroxide), and the selective utilization of components such as WSS, EBS, TSS, lignin, cellulose and hemicellulose by pure and mixed cultures of cellulolytic and xylanolytic Clostridia was monitored and correlated with the organisms' enzyme activity. For all cultures pretreatment gave higher utilization of hemicellulose and cellulose fractions; hydrogen peroxide pretreatment was more effective than NaOH treatment. Lignin utilization was not very significant even on pretreatment. C.TM1 and C.SA IV utilized hemicellulose and cellulose better than mixed cultures in selected substrates. These results help to determine the substrate composition, pretreatment conditions and enzyme system of the organism needed when designing an inoculum for agricultural waste treatment processes such as composting or biogas generation.

Initial Validation of a Knowledge-Based Measure of Social Information Processing and Anger Management

ERIC Educational Resources Information Center

Leff, Stephen S.; Cassano, Michael; MacEvoy, Julie Paquette; Costigan, Tracy

2010-01-01

Over the past fifteen years many schools have utilized aggression prevention programs. Despite these apparent advances, many programs are not examined systematically to determine the areas in which they are most effective. One reason for this is that many programs, especially those in urban under-resourced areas, do not utilize outcome measures…

The Selection of Bridge Materials Utilizing the Analytical Hierarchy Process

Treesearch

Robert L. Smith; Robert J. Bush; Daniel L. Schmoldt

1997-01-01

Effective decisions on the use of natural resources often require the input of many individuals. Determining how specific criteria affect the selection of materials can lead to better utilization of raw materials. Concrete, steel, and timber represent over 98% of the materials used for bridge construction in the United States. Highway officials must often consider...

Automated crystallographic system for high-throughput protein structure determination.

PubMed

Brunzelle, Joseph S; Shafaee, Padram; Yang, Xiaojing; Weigand, Steve; Ren, Zhong; Anderson, Wayne F

2003-07-01

High-throughput structural genomic efforts require software that is highly automated, distributive and requires minimal user intervention to determine protein structures. Preliminary experiments were set up to test whether automated scripts could utilize a minimum set of input parameters and produce a set of initial protein coordinates. From this starting point, a highly distributive system was developed that could determine macromolecular structures at a high throughput rate, warehouse and harvest the associated data. The system uses a web interface to obtain input data and display results. It utilizes a relational database to store the initial data needed to start the structure-determination process as well as generated data. A distributive program interface administers the crystallographic programs which determine protein structures. Using a test set of 19 protein targets, 79% were determined automatically.

EMS provider determinations of necessity for transport and reimbursement for EMS response, medical care, and transport: combined resource document for the National Association of EMS Physicians position statements.

PubMed

Millin, Michael G; Brown, Lawrence H; Schwartz, Brian

2011-01-01

With increasing demands for emergency medical services (EMS), many EMS jurisdictions are utilizing EMS provider-initiated nontransport policies as a method to offload potentially nonemergent patients from the EMS system. EMS provider determination of medical necessity, resulting in nontransport of patients, has the potential to avert unnecessary emergency department visits. However, EMS systems that utilize these policies must have additional education for the providers, a quality improvement process, and active physician oversight. In addition, EMS provider determination of nontransport for a specific situation should be supported by evidence in the peer-reviewed literature that the practice is safe. Further, EMS systems that do not utilize these programs should not be financially penalized. Payment for EMS services should be based on the prudent layperson standard. EMS systems that do utilize nontransport policies should be appropriately reimbursed, as this represents potential cost savings to the health care system.

Natural fiber production, harvesting, and preliminary processing: options and opportunities

USDA-ARS?s Scientific Manuscript database

The utilization of natural fibers and plant oils in bio-products introduces numerous logistical challenges not typically encountered with non-agricultural resources. Once it has been determined that a plant material is suitable for commercial development, the production, harvesting, and processing s...

Volumetric measurement of tank volume

NASA Technical Reports Server (NTRS)

Walter, Richard T. (Inventor); Vanbuskirk, Paul D. (Inventor); Weber, William F. (Inventor); Froebel, Richard C. (Inventor)

1991-01-01

A method is disclosed for determining the volume of compressible gas in a system including incompressible substances in a zero-gravity environment consisting of measuring the change in pressure (delta P) for a known volume change rate (delta V/delta t) in the polytrophic region between isothermal and adiabatic conditions. The measurements are utilized in an idealized formula for determining the change in isothermal pressure (delta P sub iso) for the gas. From the isothermal pressure change (delta iso) the gas volume is obtained. The method is also applicable to determination of gas volume by utilizing work (W) in the compression process. In a passive system, the relationship of specific densities can be obtained.

Utilization of protein intrinsic disorder knowledge in structural proteomics

PubMed Central

Oldfield, Christopher J.; Xue, Bin; Van, Ya-Yue; Ulrich, Eldon L.; Markley, John L.; Dunker, A. Keith; Uversky, Vladimir N.

2014-01-01

Intrinsically disordered proteins (IDPs) and proteins with long disordered regions are highly abundant in various proteomes. Despite their lack of well-defined ordered structure, these proteins and regions are frequently involved in crucial biological processes. Although in recent years these proteins have attracted the attention of many researchers, IDPs represent a significant challenge for structural characterization since these proteins can impact many of the processes in the structure determination pipeline. Here we investigate the effects of IDPs on the structure determination process and the utility of disorder prediction in selecting and improving proteins for structural characterization. Examination of the extent of intrinsic disorder in existing crystal structures found that relatively few protein crystal structures contain extensive regions of intrinsic disorder. Although intrinsic disorder is not the only cause of crystallization failures and many structured proteins cannot be crystallized, filtering out highly disordered proteins from structure-determination target lists is still likely to be cost effective. Therefore it is desirable to avoid highly disordered proteins from structure-determination target lists and we show that disorder prediction can be applied effectively to enrich structure determination pipelines with proteins more likely to yield crystal structures. For structural investigation of specific proteins, disorder prediction can be used to improve targets for structure determination. Finally, a framework for considering intrinsic disorder in the structure determination pipeline is proposed. PMID:23232152

Expanded plug method for developing circumferential mechanical properties of tubular materials

DOEpatents

Hendrich, William Ray; McAfee, Wallace Jefferson; Luttrell, Claire Roberta

2006-11-28

A method for determining the circumferential properties of a tubular product, especially nuclear fuel cladding, utilizes compression of a polymeric plug within the tubular product to determine strain stress, yield stress and other properties. The process is especially useful in the determination of aging properties such as fuel rod embrittlement after long burn-down.

Exploring Flow Procedures for Diazonium Formation.

PubMed

Hu, Te; Baxendale, Ian R; Baumann, Marcus

2016-07-14

The synthesis of diazonium salts is historically an important transformation extensively utilized in dye manufacture. However the highly reactive nature of the diazonium functionality has additionally led to the development of many new reactions including several carbon-carbon bond forming processes. It is therefore highly desirable to determine optimum conditions for the formation of diazonium compounds utilizing the latest processing tools such as flow chemistry to take advantage of the increased safety and continuous manufacturing capabilities. Herein we report a series of flow-based procedures to prepare diazonium salts for subsequent in-situ consumption.

Design requirements for operational earth resources ground data processing

NASA Technical Reports Server (NTRS)

Baldwin, C. J.; Bradford, L. H.; Burnett, E. S.; Hutson, D. E.; Kinsler, B. A.; Kugle, D. R.; Webber, D. S.

1972-01-01

Realistic tradeoff data and evaluation techniques were studied that permit conceptual design of operational earth resources ground processing systems. Methodology for determining user requirements that utilize the limited information available from users is presented along with definitions of sensor capabilities projected into the shuttle/station era. A tentative method is presented for synthesizing candidate ground processing concepts.

Enhancement of LEEDS Decision Tools for E-Craft

DTIC Science & Technology

2012-03-13

software tool was conducted to determine how to best incorporate RCM into the FMEA process already a part of LEEDS. Plans were made to enhance the...as opposed to implementing a strictly scheduled and costly equipment maintenance program. Utilizing the FMEA process already a part of LEEDS

Capacitance Sensors for Nondestructive Moisture Determination in Agricultural and Bio-fuel materials

USDA-ARS?s Scientific Manuscript database

Moisture content of wood chips, pellets, switch grass powders, and similar organic bio-fuel materials is an important property to be known to determine their utility and energy efficiency at various stages of their processing and storage. Several moisture measuring instruments are available in the m...

Ultrawideband asynchronous tracking system and method

NASA Technical Reports Server (NTRS)

Arndt, G. Dickey (Inventor); Ngo, Phong H. (Inventor); Phan, Chau T. (Inventor); Gross, Julia A. (Inventor); Ni, Jianjun (Inventor); Dusl, John (Inventor)

2012-01-01

A passive tracking system is provided with a plurality of ultrawideband (UWB) receivers that is asynchronous with respect to a UWB transmitter. A geometry of the tracking system may utilize a plurality of clusters with each cluster comprising a plurality of antennas. Time Difference of Arrival (TDOA) may be determined for the antennas in each cluster and utilized to determine Angle of Arrival (AOA) based on a far field assumption regarding the geometry. Parallel software communication sockets may be established with each of the plurality of UWB receivers. Transfer of waveform data may be processed by alternately receiving packets of waveform data from each UWB receiver. Cross Correlation Peak Detection (CCPD) is utilized to estimate TDOA information to reduce errors in a noisy, multipath environment.

Passive Tracking System and Method

NASA Technical Reports Server (NTRS)

Arndt, G. Dickey (Inventor); Ngo, Phong H. (Inventor); Chen, Henry A. (Inventor); Phan, Chau T. (Inventor); Bourgeois, Brian A. (Inventor); Dusl, Jon (Inventor); Hill, Brent W. (Inventor)

2003-01-01

Systems and methods are disclosed for passively determining the location of a moveable transmitter utilizing a pair of phase shifts at a receiver for extracting a direction vector from a receiver to the transmitter. In a preferred embodiment, a phase difference between the transmitter and receiver is extracted utilizing a noncoherent demodulator in the receiver. The receiver includes an antenna array with three antenna elements, which preferably are patch antenna elements spaced apart by one-half wavelength. Three receiver channels are preferably utilized for simultaneously processing the received signal from each of the three antenna elements. Multipath transmission paths for each of the three receiver channels are indexed so that comparisons of the same multipath component are made for each of the three receiver channels. The phase difference for each received signal is determined by comparing only the magnitudes of received and stored modulation signals to determine a winning modulation symbol.

Passive Tracking System and Method

NASA Technical Reports Server (NTRS)

Arndt, G. Dickey (Inventor); Ngo, Phong H. (Inventor); Chen, Henry A. (Inventor); Phan, Chau T. (Inventor); Bourgeois, Brian A. (Inventor); Dusl, John (Inventor); Hill, Brent W. (Inventor)

2005-01-01

System and methods are disclosed for passively determining the location of a moveable transmitter utilizing a pair of phase shifts at a receiver for extracting a direction vector from a receiver to the transmitter. In a preferred embodiment, a phase difference between the transmitter and receiver is extracted utilizing a noncoherent demodulator in the receiver. The receiver includes antenna array with three antenna elements, which preferably are patch antenna elements placed apart by one-half wavelength. Three receiver channels are preferably utilized for simultaneously processing the received signal from each of the three antenna elements. Multipath transmission paths for each of the three receiver channels are indexed so that comparisons of the same multipath component are made for each of the three receiver channels. The phase difference for each received signal is determined by comparing only the magnitudes of received and stored modulation signals to determine a winning modulation symbol.

7 CFR 1955.141 - Transferring title.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Transferring title. (a)-(c) [Reserved] (d) Rent increases for MFH property. After approval of a credit sale for... project operation (and a utility allowance, if applicable) to determine if a rent increase may be needed... in processing the request for a rent increase. In processing the rent increase, the purchaser will...

An Organizational Diffusion Study on Distance Education

ERIC Educational Resources Information Center

Smith, Lillian Upton; Richter, Donna L.; Miner, Kathleen R.; Watkins, Ken; Usdan, Stuart

2005-01-01

This research explored the diffusion process of distance education in schools of public health to determine best practices in the planning and implementation of future programs. The researcher traced the diffusion process by utilizing a multiple-case study methodology using a semi-structured interview to collect the perceptions of Distance…

The distribution of environmental contaminants and pharmaceuticals among skim milk, milk fat, curd, whey, and milk protein fractions through milk processing

USDA-ARS?s Scientific Manuscript database

Twenty-seven environmental contaminants and pharmaceuticals encompassing a wide range of physicochemical properties were utilized to determine the effects of milk processing on xenobiotic distribution among milk fractions. Target compounds included radiolabeled antibiotics [ciprofloxacin (CIPR), cl...

PROCESSING CENTER FOR CALIFORNIA JUNIOR COLLEGE LIBRARIES--A PRELIMINARY STUDY.

ERIC Educational Resources Information Center

MOORE, EVERETT L.

VARIOUS COUNTY, PUBLIC, AND SCHOOL LIBRARIES HAVE UTILIZED THE SERVICES OF CENTRALIZED CATALOGING AND PROCESSING CENTERS. TO DETERMINE WHETHER PRACTICAL AND FINANCIAL CONSIDERATIONS MIGHT ENABLE PUBLIC JUNIOR COLLEGES IN SOUTHERN CALIFORNIA TO ESTABLISH SUCH A SYSTEM, 35 JUNIOR COLLEGES WERE SENT A CHECKLIST OF 100 TITLES, A QUESTIONNAIRE…

Visually enhanced CCTV digital surveillance utilizing Intranet and Internet.

PubMed

Ozaki, Nobuyuki

2002-07-01

This paper describes a solution for integrated plant supervision utilizing closed circuit television (CCTV) digital surveillance. Three basic requirements are first addressed as the platform of the system, with discussion on the suitable video compression. The system configuration is described in blocks. The system provides surveillance functionality: real-time monitoring, and process analysis functionality: a troubleshooting tool. This paper describes the formulation of practical performance design for determining various encoder parameters. It also introduces image processing techniques for enhancing the original CCTV digital image to lessen the burden on operators. Some screenshots are listed for the surveillance functionality. For the process analysis, an image searching filter supported by image processing techniques is explained with screenshots. Multimedia surveillance, which is the merger with process data surveillance, or the SCADA system, is also explained.

Optimizing Utilization of Detectors

DTIC Science & Technology

2016-03-01

provide a quantifiable process to determine how much time should be allocated to each task sharing the same asset . This optimized expected time... allocation is calculated by numerical analysis and Monte Carlo simulation. Numerical analysis determines the expectation by involving an integral and...determines the optimum time allocation of the asset by repeatedly running experiments to approximate the expectation of the random variables. This

Utilization of information technology in eastern North Carolina physician practices: determining the existence of a digital divide.

PubMed

Rosenthal, David A; Layman, Elizabeth J

2008-02-13

The United States Department of Health and Human Services (DHHS) has emphasized the importance of utilizing health information technologies, thus making the availability of electronic resources critical for physicians across the country. However, few empirical assessments exist regarding the current status of computerization and utilization of electronic resources in physician offices and physicians' perceptions of the advantages and disadvantages of computerization. Through a survey of physicians' utilization and perceptions of health information technology, this study found that a "digital divide" existed for eastern North Carolina physicians in smaller physician practices. The physicians in smaller practices were less likely to utilize or be interested in utilizing electronic health records, word processing applications, and the Internet.

Space processing of chalcogenide glass

NASA Technical Reports Server (NTRS)

Larsen, D. C.; Ali, M. I.

1977-01-01

The manner in which the weightless, containerless nature of in-space processing can be successfully utilized to improve the quality of infrared transmitting chalcogenide glasses is determined. The technique of space processing chalcogenide glass was developed, and the process and equipment necessary to do so was defined. Earthbound processing experiments with As2S3 and G28Sb12Se60 glasses were experimented with. Incorporated into these experiments is the use of an acoustic levitation device.

Report on the study of the tax and rate treatment of renewable energy projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadley, S.W.; Hill, L.J.; Perlack, R.D.

1993-12-01

This study was conducted in response to the requirements of Section 1205 of the Energy Policy Act of 1992 (EPACT), which states: The Secretary (of Energy), in conjunction with State regulatory commissions, shall undertake a study to determine if conventional taxation and ratemaking procedures result in economic barriers to or incentives for renewable energy power plants compared to conventional power plants. The purpose of the study, therefore, is not to compare the cost-effectiveness of different types of renewable and conventional electric generating plants. Rather, it is to determine the relative impact of conventional ratemaking and taxation procedures on the selectionmore » of renewable power plants compared to conventional ones. To make this determination, we quantify the technical and financial parameters of renewable and conventional electric generating technologies, and hold them fixed throughout the study. Then, we vary taxation and ratemaking procedures to determine their effects on the financial criteria that investor-owned electric utilities (IOUs) and nonutility electricity generators (NUGs) use to make technology-adoption decisions. In the planning process of a typical utility, the opposite is usually the case. That is, utilities typically hold ratemaking and taxation procedures constant and look for the least-cost mix of resources, varying the values of engineering and financial parameters of generating plants in the process.« less

Preliminary System Analysis of In Situ Resource Utilization for Mars Human Exploration

NASA Technical Reports Server (NTRS)

Rapp, Donald; Andringa, Jason; Easter, Robert; Smith, Jeffrey H .; Wilson, Thomas; Clark, D. Larry; Payne, Kevin

2005-01-01

We carried out a system analysis of processes for utilization of Mars resources to support human exploration of Mars by production of propellants from indigenous resources. Seven ISRU processes were analyzed to determine mass. power and propellant storage volume requirements. The major elements of each process include C02 acquisition, chemical conversion, and storage of propellants. Based on a figure of merit (the ratio of the mass of propellants that must be brought from Earth in a non-ISRU mission to the mass of the ISRU system. tanks and feedstocks that must be brought from Earth for a ISRU mission) the most attractive process (by far); is one where indigenous Mars water is accessible and this is processed via Sabatier/Electrolysis to methane and oxygen. These processes are technically relatively mature. Other processes with positive leverage involve reverse water gas shift and solid oxide electrolysis.

The impact of the participation of settlers to the formation of environment in Kampung Nelayan Belawan Medan

NASA Astrophysics Data System (ADS)

Marpaung, B. O. Y.; Waginah

2018-03-01

Every existence of community settlements that formed has related to social, culture, and economy that exists in that society. Participation is a process that involving human interaction towards each other, of these interactions creates activities that potentially form a new space (Hendriksen, et al., 2012). Problems in this research are related to community involvement in building residential, determining land used, building roads, and utilities in Kampung Nelayan Belawan Medan residential. The aim of this research is to find the community involvement of building residential, determining land used, building roads, and utilities in Kampung Nelayan Belawan Medan residential. In the process of collecting data, researchers conducted field observation and interviews. Then the researchers connect the theory and interpretation of data in determining the method of data analysis. Then the researchers connect the theory and interpretation of data in determining the method of data analysis. The discovery of this research is that the formation of settlement spaces in the fishing village is inseparable from the participation in Kampung Nelayan Belawan Medan residential.

Improved methods for the determination of drying conditions and fraction insoluble solids (FIS) in biomass pretreatment slurry

DOE PAGES

Sluiter, Amie; Sluiter, Justin; Wolfrum, Ed; ...

2016-05-20

Accurate and precise chemical characterization of biomass feedstocks and process intermediates is a requirement for successful technical and economic evaluation of biofuel conversion technologies. The uncertainty in primary measurements of the fraction insoluble solid (FIS) content of dilute acid pretreated corn stover slurry is the major contributor to uncertainty in yield calculations for enzymatic hydrolysis of cellulose to glucose. This uncertainty is propagated through process models and impacts modeled fuel costs. The challenge in measuring FIS is obtaining an accurate measurement of insoluble matter in the pretreated materials, while appropriately accounting for all biomass derived components. Three methods were testedmore » to improve this measurement. One used physical separation of liquid and solid phases, and two utilized direct determination of dry matter content in two fractions. We offer a comparison of drying methods. Lastly, our results show utilizing a microwave dryer to directly determine dry matter content is the optimal method for determining FIS, based on the low time requirements and the method optimization done using model slurries.« less

Atmospheric and oceanographic research review, 1978. [global weather, ocean/air interactions, and climate

NASA Technical Reports Server (NTRS)

1978-01-01

Research activities related to global weather, ocean/air interactions, and climate are reported. The global weather research is aimed at improving the assimilation of satellite-derived data in weather forecast models, developing analysis/forecast models that can more fully utilize satellite data, and developing new measures of forecast skill to properly assess the impact of satellite data on weather forecasting. The oceanographic research goal is to understand and model the processes that determine the general circulation of the oceans, focusing on those processes that affect sea surface temperature and oceanic heat storage, which are the oceanographic variables with the greatest influence on climate. The climate research objective is to support the development and effective utilization of space-acquired data systems in climate forecast models and to conduct sensitivity studies to determine the affect of lower boundary conditions on climate and predictability studies to determine which global climate features can be modeled either deterministically or statistically.

Assessment of sulfide production risk in soil during the infiltration of domestic wastewater treated by a sulfur-utilizing denitrification process.

PubMed

Ghorbel, L; Coudert, L; Gilbert, Y; Mercier, G; Blais, J F

2016-10-01

This study aimed to determine the potential of sulfide generation during infiltration through soil of domestic wastewater treated by a sulfur-utilizing denitrification process. Three types of soil with different permeability rates (K s = 0.028, 0.0013, and 0.00015 cm/s) were investigated to evaluate the potential risk of sulfur generation during the infiltration of domestic wastewater treated by a sulfur-utilizing denitrification system. These soils were thoroughly characterized and tested to assess their capacity to be used as drainages for wastewaters. Experiments were conducted under two operating modes (saturated and unsaturated). Sulfate, sulfide, and chemical oxygen demand (COD) levels were determined over a period of 100 days. Despite the high concentration of sulfates (200 mg/L) under anaerobic conditions (ORP = -297 mV), no significant amount of sulfide was generated in the aqueous (<0.2 mg/L) or gaseous (<0.15 ppm) phases. Furthermore, the soil permeability did not have a noticeable effect on the infiltration of domestic wastewater treated by a sulfur-utilizing denitrification system due to low contents of organic matter (i.e., dissolved organic carbon, DOC). The autotrophic denitrification process used to treat the domestic wastewater allowed the reduction of the concentration of biochemical oxygen demand (BOD5) below 5 mg/L, of DOC below 7 mg/L, and of COD below 100 mg/L.

Price Estimation Guidelines

NASA Technical Reports Server (NTRS)

Chamberlain, R. G.; Aster, R. W.; Firnett, P. J.; Miller, M. A.

1985-01-01

Improved Price Estimation Guidelines, IPEG4, program provides comparatively simple, yet relatively accurate estimate of price of manufactured product. IPEG4 processes user supplied input data to determine estimate of price per unit of production. Input data include equipment cost, space required, labor cost, materials and supplies cost, utility expenses, and production volume on industry wide or process wide basis.

Integrated extraction and anaerobic digestion process for recovery of nutraceuticals and biogas from pomegranate marcs

USDA-ARS?s Scientific Manuscript database

Pomegranate marc (PM), a by-product from pomegranate juice processing, has not been effectively utilized. The objectives of this study were to (1) determine the yields and properties of antioxidants (henceforth referring to total phenolics in terms of tannic acid equivalent) and oil extracted from v...

Effect of temperature on anoxic sulfide oxidation and denitrification in the bulk wastewater phase of sewer networks.

PubMed

Mathioudakis, V L; Aivasidis, A

2009-01-01

Artificial dosage of nitrate in sewer networks is considered as one of the most effective methods for odor and corrosion control. However, there is limited knowledge on the effect of temperature on the transformations that takes place during anoxic conditions. Thus, two groups of batch experiments were conducted to gain insight in the involved processes in bulk phase of a septic municipal wastewater. It can be concluded that sewer denitrification, in bulk phase, can be simplified in three stages. According to the experimental results, nitrate or nitrite is utilized for autotrophic denitrification with sulfide, while heterotrophic utilization is initiated after the completion of anoxic sulfide oxidation. Moreover, temperature is proved to have a significant impact on sewer denitrification kinetic profile, as it determines the extent of temporal nitrite accumulation. The temperature coefficient of each anoxic process, including sulfide oxidation, nitrate utilization and denitrification/nitrite utilization is experimentally calculated and temperature dependent equations are developed, providing the rate of all anoxic processes in bulk phase of sewer wastewater, in any given temperature.

Flexible Visual Processing in Young Adults with Autism: The Effects of Implicit Learning on a Global-Local Task

ERIC Educational Resources Information Center

Hayward, Dana A.; Shore, David I.; Ristic, Jelena; Kovshoff, Hanna; Iarocci, Grace; Mottron, Laurent; Burack, Jacob A.

2012-01-01

We utilized a hierarchical figures task to determine the default level of perceptual processing and the flexibility of visual processing in a group of high-functioning young adults with autism (n = 12) and a typically developing young adults, matched by chronological age and IQ (n = 12). In one task, participants attended to one level of the…

Fracture Toughness of Carbon Fiber Composites Containing Various Fiber Sizings and a Puncture Self-Healing Thermoplastic Matrix

NASA Technical Reports Server (NTRS)

Cano, Roberto J.; Grimsley, Brian W.; Ratcliffe, James G.; Gordon, Keith L.; Smith, Joseph G.; Siochi, Emilie J.

2015-01-01

Ongoing efforts at NASA Langley Research Center (LaRC) have resulted in the identification of several commercially available thermoplastic resin systems which self-heal after ballistic impact and through penetration. One of these resins, polybutylene graft copolymer (PBg), was selected as a matrix for processing with unsized carbon fibers to fabricate reinforced composites for further evaluation. During process development, data from thermo-physical analyses was utilized to determine a processing cycle to fabricate laminate panels, which were analyzed by photo microscopy and acid digestion. The process cycle was further optimized based on these results to fabricate panels for mechanical property characterization. The results of the processing development effort of this composite material, as well as the results of the mechanical property characterization, indicated that bonding between the fiber and PBg was not adequate. Therefore, three sizings were investigated in this work to assess their potential to improve fiber/matrix bonding compared to previously tested unsized IM7 fiber. Unidirectional prepreg was made at NASA LaRC from three sized carbon fibers and utilized to fabricate test coupons that were tested in double cantilever beam configurations to determine GIc fracture toughness.

Relationship between cattle temperament as determined by exit velocity carcass merit in beef cattle

USDA-ARS?s Scientific Manuscript database

The objective of this trial was to use cattle temperament, as determined by exit velocity only, as a means to evaluate the impact of temperament on carcass merit and the possible utilization of exit velocity alone as a sorting tool within the feedlot. At the time of processing, exit velocity and bod...

On optimizing the treatment of exchange perturbations

NASA Technical Reports Server (NTRS)

Hirschfelder, J. O.; Chipman, D. M.

1972-01-01

A method using the zeroth plus first order wave functions, obtained by optimizing the basic equation used in exchange perturbation treatments, is utilized in an attempt to determine the exact energy and wave function in the exchange process. Attempts to determine the first order perturbation solution by optimizing the sum of the first and second order energies were unsuccessful.

Determination of the Formula of a Hydrate: A Greener Alternative

ERIC Educational Resources Information Center

Klingshirn, Marc A.; Wyatt, Allison F.; Hanson, Robert M.; Spessard, Gary O.

2008-01-01

We are currently in the process of incorporating green chemistry throughout the chemistry curriculum. In this article we describe how we applied the principles of green chemistry in one of our first-semester general chemistry courses, specifically in relation to the determination of the formula of a hydrate. We utilize a copper hydrate salt that…

A Needs Assessment for the Introduction of a Food Science Program at the Univ. of Guyana

ERIC Educational Resources Information Center

Morrison, Donna

2012-01-01

This research describes the outcome of a needs assessment to determine whether the Univ. of Guyana should introduce a Food Science program. The research design utilized interviews and questionnaires to large manufacturing organizations and agroprocessors to determine if the required skills are available for the manufacturing process. Results…

Student Perceived and Determined Knowledge of Biology Concepts in an Upper-Level Biology Course

ERIC Educational Resources Information Center

Ziegler, Brittany; Montplaisir, Lisa

2014-01-01

Students who lack metacognitive skills can struggle with the learning process. To be effective learners, students should recognize what they know and what they do not know. This study examines the relationship between students' perception of their knowledge and determined knowledge in an upper-level biology course utilizing a pre/posttest…

Improving Responsiveness to Intervention in a Virtual Publically Supported Program: An Action Research

ERIC Educational Resources Information Center

Kerr, Rachel A.

2014-01-01

The purpose of this action research study was to design, implement, analyze, and evaluate a series of interventions to increase the elementary teachers' utilization of the RtI process. Another purpose of the study was to determine the teachers' background knowledge and perceptions about the Responsiveness to Intervention (RtI) process at the…

Case Study Application Of Determining End Of Asset Physical Life Using Survival Analysis:(WERF Report INFR2R11a)

EPA Science Inventory

Abstract:This case study application provides discussion on a selected application of advanced concepts, included in the End of Asset Life Reinvestment decision-making process tool, using a utility practitioner’s data set. The tool provides step-by-step process guidance to the as...

Multi-photon EIT

NASA Astrophysics Data System (ADS)

Laarits, Toomas; O'Gorman, Bryan; Crescimanno, Michael

2008-03-01

We describe and solve a quantum optics models for multiphoton interrogation of an electromagnetically induced transparency (EIT) resonance. Multiphoton EIT, like its well studied Lambda-system EIT progenitor, is a generalization of the N-resonance process recently studied for atomic time keeping. The solution of these models allows a preliminary determination of this processes utility as the basis of a frequency standard.

Internet Access, Use and Sharing Levels among Students during the Teaching-Learning Process

ERIC Educational Resources Information Center

Tutkun, Omer F.

2011-01-01

The purpose of this study was to determine the awareness among students and levels regarding student access, use, and knowledge sharing during the teaching-learning process. The triangulation method was utilized in this study. The population of the research universe was 21,747. The student sample population was 1,292. Two different data collection…

Photogrammetry Toolbox Reference Manual

NASA Technical Reports Server (NTRS)

Liu, Tianshu; Burner, Alpheus W.

2014-01-01

Specialized photogrammetric and image processing MATLAB functions useful for wind tunnel and other ground-based testing of aerospace structures are described. These functions include single view and multi-view photogrammetric solutions, basic image processing to determine image coordinates, 2D and 3D coordinate transformations and least squares solutions, spatial and radiometric camera calibration, epipolar relations, and various supporting utility functions.

Study of Dynamic Characteristics of Aeroelastic Systems Utilizing Randomdec Signatures

NASA Technical Reports Server (NTRS)

Chang, C. S.

1975-01-01

The feasibility of utilizing the random decrement method in conjunction with a signature analysis procedure to determine the dynamic characteristics of an aeroelastic system for the purpose of on-line prediction of potential on-set of flutter was examined. Digital computer programs were developed to simulate sampled response signals of a two-mode aeroelastic system. Simulated response data were used to test the random decrement method. A special curve-fit approach was developed for analyzing the resulting signatures. A number of numerical 'experiments' were conducted on the combined processes. The method is capable of determining frequency and damping values accurately from randomdec signatures of carefully selected lengths.

Digital correlator with fewer IC's

NASA Technical Reports Server (NTRS)

Apple, G. G.; Rubin, L.

1979-01-01

Digital correlator requires only few integrated circuits to determine synchronization of two 24-bit digital words. Circuit is easily reduced or expanded to accommodate shorter or longer words and can be utilized in industrial and commercial data processing and telecommunications.

Design, processing and testing of LSI arrays hybrid microelectronics task

NASA Technical Reports Server (NTRS)

Himmel, R. P.; Stuhlbarg, S. M.; Salmassy, S.

1978-01-01

Those factors affecting the cost of electronic subsystems utilizing LSI microcircuits were determined and the most efficient methods for low cost packaging of LSI devices as a function of density and reliability were developed.

Valuing Treatments for Parkinson Disease Incorporating Process Utility: Performance of Best-Worst Scaling, Time Trade-Off, and Visual Analogue Scales.

PubMed

Weernink, Marieke G M; Groothuis-Oudshoorn, Catharina G M; IJzerman, Maarten J; van Til, Janine A

2016-01-01

The objective of this study was to compare treatment profiles including both health outcomes and process characteristics in Parkinson disease using best-worst scaling (BWS), time trade-off (TTO), and visual analogue scales (VAS). From the model comprising of seven attributes with three levels, six unique profiles were selected representing process-related factors and health outcomes in Parkinson disease. A Web-based survey (N = 613) was conducted in a general population to estimate process-related utilities using profile-based BWS (case 2), multiprofile-based BWS (case 3), TTO, and VAS. The rank order of the six profiles was compared, convergent validity among methods was assessed, and individual analysis focused on the differentiation between pairs of profiles with methods used. The aggregated health-state utilities for the six treatment profiles were highly comparable for all methods and no rank reversals were identified. On the individual level, the convergent validity between all methods was strong; however, respondents differentiated less in the utility of closely related treatment profiles with a VAS or TTO than with BWS. For TTO and VAS, this resulted in nonsignificant differences in mean utilities for closely related treatment profiles. This study suggests that all methods are equally able to measure process-related utility when the aim is to estimate the overall value of treatments. On an individual level, such as in shared decision making, BWS allows for better prioritization of treatment alternatives, especially if they are closely related. The decision-making problem and the need for explicit trade-off between attributes should determine the choice for a method. Copyright © 2016. Published by Elsevier Inc.

Teacher Reported Job Satisfaction and Teacher Reported Understanding of the Evaluation Process: An Exploratory Mixed-Methods Case Study of One Urban Public School District

ERIC Educational Resources Information Center

Walsh, Maura

2013-01-01

Although there is wide consensus that teacher evaluation processes should be used to identify and measure effective teaching, this has always been an elusive goal. How teachers perceive the evaluative process is a crucial determiner of how the results of the evaluations are utilized. In 2010, the Massachusetts Department of Elementary and…

Techno-environmental assessment of the green biorefinery concept: Combining process simulation and life cycle assessment at an early design stage.

PubMed

Corona, Andrea; Ambye-Jensen, Morten; Vega, Giovanna Croxatto; Hauschild, Michael Zwicky; Birkved, Morten

2018-09-01

The Green biorefinery (GBR) is a biorefinery concept that converts fresh biomass into value-added products. The present study combines a Process Flowsheet Simulation (PFS) and Life Cycle Assessment (LCA) to evaluate the technical and environmental performance of different GBR configurations and the cascading utilization of the GBR output. The GBR configurations considered in this study, test alternatives in the three main steps of green-biorefining: fractionation, precipitation, and protein separation. The different cascade utilization alternatives analyse different options for press-pulp utilization, and the LCA results show that the environmental profile of the GBR is highly affected by the utilization of the press-pulp and thus by the choice of conventional product replaced by the press-pulp. Furthermore, scenario analysis of different GBR configurations shows that higher benefits can be achieved by increasing product yields rather than lowering energy consumption. Green biorefining is shown to be an interesting biorefining concept, especially in a Danish context. Biorefining of green biomass is technically feasible and can bring environmental savings, when compared to conventional production methods. However, the savings will be determined by the processing involved in each conversion stage and on the cascade utilization of the different platform products. Copyright © 2018 Elsevier B.V. All rights reserved.

Initial Validation of a Knowledge-Based Measure of Social Information Processing and Anger Management

PubMed Central

Cassano, Michael; MacEvoy, Julie Paquette; Costigan, Tracy

2010-01-01

Over the past fifteen years many schools have utilized aggression prevention programs. Despite these apparent advances, many programs are not examined systematically to determine the areas in which they are most effective. One reason for this is that many programs, especially those in urban under-resourced areas, do not utilize outcome measures that are sensitive to the needs of ethnic minority students. The current study illustrates how a new knowledge-based measure of social information processing and anger management techniques was designed through a partnership-based process to ensure that it would be sensitive to the needs of urban, predominately African American youngsters, while also having broad potential applicability for use as an outcome assessment tool for aggression prevention programs focusing upon social information processing. The new measure was found to have strong psychometric properties within a sample of urban predominately African American youth, as item analyses suggested that almost all items discriminate well between more and less knowledgeable individuals, that the test-retest reliability of the measure is strong, and that the measure appears to be sensitive to treatment changes over time. In addition, the overall score of this new measure is moderately associated with attributions of hostility on two measures (negative correlations) and demonstrates a low to moderate negative association with peer and teacher report measures of overt and relational aggression. More research is needed to determine the measure's utility outside of the urban school context. PMID:20449645

Field Trial Results of a 14-channel GPR Integrated with a U.S. Program for 3-D Utility Mapping

NASA Astrophysics Data System (ADS)

Anspach, James H.

2013-04-01

Existing underground utilities continue to be a leading cause of highway construction delay claims in the United States. Although 80-90% of existing utilities can typically be discovered and mapped using a wide range of geophysical tools, there is a recognizable need to improve the process. Existing shortcomings to the utility mapping process include a lack of viable depth attributes, long field occupation times, low experience level of the field technicians, and separate survey / geophysics functions. The U.S. National Academies and its Transportation Research Board recently concluded a project on alleviating the existing utility mapping shortcomings through the development of enhanced GPR. An existing commercial 400MHz 14-channel towed array was enhanced with positioning and interpretation hardware and software over a 3-year US 2M program. Field trials for effectiveness were conducted in a city suburb commercialized environment where the relative permittivity values averaged 9.4. The effectiveness of enhanced GPR was compared to traditional utility mapping techniques (Single Channel GPR, FDEM, Acoustic, Sondes, Gradiometric Magnetometers) during the project. The project area utilities included natural gas, water, electric, telephone, cable, storm, sanitary, traffic control, and several unknown function lines. Depths for these utilities were mostly unknown. 81% of known (from records and field appurtenance visual observation) utilities were detected via traditional geophysical means. These traditional geophysical means also detected 14% additional and previously "unknown" utilities. The enhanced GPR detected approximately 40% of the known and unknown utilities, and found an additional 6% of utilities that were previously undetected. These additional utilities were subsequently determined to be small diameter abandoned water and gas systems in very poor and broken condition. Although it did well with metallic water and gas lines, communication and electric utilities were mostly undetectable. Through a ground-truthing program of test holes to expose utilities, the depth values derived from the enhanced GPR were fairly consistent and within 15 cm of actual depth. The incomplete underground picture determined by the enhanced GPR reinforces previous studies that show that the mapping of existing underground utilities is a multi-tool effort that takes highly trained and skilled field technicians and data interpreters. The addition of a new GPR tool is valuable in determining continuous depth profiles of imaged utilities. A second and significant benefit is the interpretation of other geotechnical data that benefit project designers. This might include showing geometry, location, intensity, and depths of either areas of anomalies, or of known structures, such as paving thickness, substrate thickness, voids, water table, soil lenses, boulders, bedrock, and so forth. The Florida Department of Transportation has decided to take advantage of this new technology and has entered into an experimental contract with Cardno TBE to incorporate several enhanced GPR arrays with traditional utility detection tools. The goal of this contract will be to provide a 3-D model of existing underground utilities for use in automated construction. The GPR 3-D data model will be melded with conventional subsurface utility engineering and mapping practices and will be required to follow the ASCE 38 standard for utility data reliability.

Summary of Skylab S-193 altimeter altitude results. [orbit calculation and studies of the ocean bottom

NASA Technical Reports Server (NTRS)

Mcgoogan, J. T.; Leitao, C. D.; Wells, W. T.

1975-01-01

The SKYLAB S-193 altimeter altitude results are presented in a concise format for further use and analysis by the scientific community. The altimeter mission and instrumentation is described along with the altimeter processing techniques and values of parameters used for processing. The determination of reference orbits is discussed, and the tracking systems utilized are tabulated. Techniques for determining satellite pointing are presented and a tabulation of pointing for each data mission included. The geographical location, the ocean bottom topography, the altimeter-determined ocean surface topography, and the altimeter automatic gain control history is presented. Some typical applications of this data are suggested.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knudsen, J.K.; Smith, C.L.

The steps involved to incorporate parameter uncertainty into the Nuclear Regulatory Commission (NRC) accident sequence precursor (ASP) models is covered in this paper. Three different uncertainty distributions (i.e., lognormal, beta, gamma) were evaluated to Determine the most appropriate distribution. From the evaluation, it was Determined that the lognormal distribution will be used for the ASP models uncertainty parameters. Selection of the uncertainty parameters for the basic events is also discussed. This paper covers the process of determining uncertainty parameters for the supercomponent basic events (i.e., basic events that are comprised of more than one component which can have more thanmore » one failure mode) that are utilized in the ASP models. Once this is completed, the ASP model is ready to be utilized to propagate parameter uncertainty for event assessments.« less

Carbon Capture and Utilization in the Industrial Sector.

PubMed

Psarras, Peter C; Comello, Stephen; Bains, Praveen; Charoensawadpong, Panunya; Reichelstein, Stefan; Wilcox, Jennifer

2017-10-03

The fabrication and manufacturing processes of industrial commodities such as iron, glass, and cement are carbon-intensive, accounting for 23% of global CO 2 emissions. As a climate mitigation strategy, CO 2 capture from flue gases of industrial processes-much like that of the power sector-has not experienced wide adoption given its high associated costs. However, some industrial processes with relatively high CO 2 flue concentration may be viable candidates to cost-competitively supply CO 2 for utilization purposes (e.g., polymer manufacturing, etc.). This work develops a methodology that determines the levelized cost ($/tCO 2 ) of separating, compressing, and transporting carbon dioxide. A top-down model determines the cost of separating and compressing CO 2 across 18 industrial processes. Further, the study calculates the cost of transporting CO 2 via pipeline and tanker truck to appropriately paired sinks using a bottom-up cost model and geo-referencing approach. The results show that truck transportation is generally the low-cost alternative given the relatively small volumes (ca. 100 kt CO 2 /a). We apply our methodology to a regional case study in Pennsylvania, which shows steel and cement manufacturing paired to suitable sinks as having the lowest levelized cost of capture, compression, and transportation.

Data processing 1: Advancements in machine analysis of multispectral data

NASA Technical Reports Server (NTRS)

Swain, P. H.

1972-01-01

Multispectral data processing procedures are outlined beginning with the data display process used to accomplish data editing and proceeding through clustering, feature selection criterion for error probability estimation, and sample clustering and sample classification. The effective utilization of large quantities of remote sensing data by formulating a three stage sampling model for evaluation of crop acreage estimates represents an improvement in determining the cost benefit relationship associated with remote sensing technology.

Performance processes within affect-related performance zones: a multi-modal investigation of golf performance.

PubMed

van der Lei, Harry; Tenenbaum, Gershon

2012-12-01

Individual affect-related performance zones (IAPZs) method utilizing Kamata et al. (J Sport Exerc Psychol 24:189-208, 2002) probabilistic model of determining the individual zone of optimal functioning was utilized as idiosyncratic affective patterns during golf performance. To do so, three male golfers of a varsity golf team were observed during three rounds of golf competition. The investigation implemented a multi-modal assessment approach in which the probabilistic relationship between affective states and both, performance process and performance outcome, measures were determined. More specifically, introspective (i.e., verbal reports) and objective (heart rate and respiration rate) measures of arousal were incorporated to examine the relationships between arousal states and both, process components (i.e., routine consistency, timing), and outcome scores related to golf performance. Results revealed distinguishable and idiosyncratic IAPZs associated with physiological and introspective measures for each golfer. The associations between the IAPZs and decision-making or swing/stroke execution were strong and unique for each golfer. Results are elaborated using cognitive and affect-related concepts, and applications for practitioners are provided.

Recent progress in solution plasma-synthesized-carbon-supported catalysts for energy conversion systems

NASA Astrophysics Data System (ADS)

Lun Li, Oi; Lee, Hoonseung; Ishizaki, Takahiro

2018-01-01

Carbon-based materials have been widely utilized as the electrode materials in energy conversion and storage technologies, such as fuel cells and metal-air batteries. In these systems, the oxygen reduction reaction is an important step that determines the overall performance. A novel synthesis route, named the solution plasma process, has been recently utilized to synthesize various types of metal-based and heteroatom-doped carbon catalysts. In this review, we summarize cutting-edge technologies involving the synthesis and modeling of carbon-supported catalysts synthesized via solution plasma process, followed by current progress on the electrocatalytic performance of these catalysts. This review provides the fundamental and state-of-the-art performance of solution-plasma-synthesized electrode materials, as well as the remaining scientific and technological challenges for this process.

Using Integer Manipulatives: Representational Determinism

ERIC Educational Resources Information Center

Bossé, Michael J.; Lynch-Davis, Kathleen; Adu-Gyamfi, Kwaku; Chandler, Kayla

2016-01-01

Teachers and students commonly use various concrete representations during mathematical instruction. These representations can be utilized to help students understand mathematical concepts and processes, increase flexibility of thinking, facilitate problem solving, and reduce anxiety while doing mathematics. Unfortunately, the manner in which some…

Prediction of Tensile Strength of Friction Stir Weld Joints with Adaptive Neuro-Fuzzy Inference System (ANFIS) and Neural Network

NASA Technical Reports Server (NTRS)

Dewan, Mohammad W.; Huggett, Daniel J.; Liao, T. Warren; Wahab, Muhammad A.; Okeil, Ayman M.

2015-01-01

Friction-stir-welding (FSW) is a solid-state joining process where joint properties are dependent on welding process parameters. In the current study three critical process parameters including spindle speed (??), plunge force (????), and welding speed (??) are considered key factors in the determination of ultimate tensile strength (UTS) of welded aluminum alloy joints. A total of 73 weld schedules were welded and tensile properties were subsequently obtained experimentally. It is observed that all three process parameters have direct influence on UTS of the welded joints. Utilizing experimental data, an optimized adaptive neuro-fuzzy inference system (ANFIS) model has been developed to predict UTS of FSW joints. A total of 1200 models were developed by varying the number of membership functions (MFs), type of MFs, and combination of four input variables (??,??,????,??????) utilizing a MATLAB platform. Note EFI denotes an empirical force index derived from the three process parameters. For comparison, optimized artificial neural network (ANN) models were also developed to predict UTS from FSW process parameters. By comparing ANFIS and ANN predicted results, it was found that optimized ANFIS models provide better results than ANN. This newly developed best ANFIS model could be utilized for prediction of UTS of FSW joints.

National Conference on Integrated Resource Planning: Proceedings

NASA Astrophysics Data System (ADS)

Until recently, state regulators have focused most of their attention on the development of least-cost or integrated resource planning (IRP) processes for electric utilities. A number of commissions are beginning to scrutinize the planning processes of local gas distribution companies (LDCs) because of the increased control that LDCs have over their purchased gas costs (as well as the associated risks) and because of questions surrounding the role and potential of gas end-use efficiency options. Traditionally, resource planning (LDCs) has concentrated on options for purchasing and storing gas. Integrated resource planning involves the creation of a process in which supply-side and demand-side options are integrated to create a resource mix that reliably satisfies customers' short-term and long-term energy service needs at the lowest cost. As applied to gas utilities, an integrated resource plan seeks to balance cost and reliability, and should not be interpreted simply as the search for lowest commodity costs. The National Association of Regulatory Utility Commissioners' (NARUC) Energy Conservation committee asked Lawrence Berkeley Laboratory (LBL) to survey state PUCs to determine the extent to which they have undertaken least cost planning for gas utilities. The survey included the following topics: status of state PUC least-cost planning regulations and practices for gas utilities; type and scope of natural gas DSM programs in effect, including fuel substitution; economic tests and analysis methods used to evaluate DSM programs; relationship between prudency reviews of gas utility purchasing practices and integrated resource planning; and key regulatory issues facing gas utilities during the next five years.

Optimization in the utility maximization framework for conservation planning: a comparison of solution procedures in a study of multifunctional agriculture

PubMed Central

Stoms, David M.; Davis, Frank W.

2014-01-01

Quantitative methods of spatial conservation prioritization have traditionally been applied to issues in conservation biology and reserve design, though their use in other types of natural resource management is growing. The utility maximization problem is one form of a covering problem where multiple criteria can represent the expected social benefits of conservation action. This approach allows flexibility with a problem formulation that is more general than typical reserve design problems, though the solution methods are very similar. However, few studies have addressed optimization in utility maximization problems for conservation planning, and the effect of solution procedure is largely unquantified. Therefore, this study mapped five criteria describing elements of multifunctional agriculture to determine a hypothetical conservation resource allocation plan for agricultural land conservation in the Central Valley of CA, USA. We compared solution procedures within the utility maximization framework to determine the difference between an open source integer programming approach and a greedy heuristic, and find gains from optimization of up to 12%. We also model land availability for conservation action as a stochastic process and determine the decline in total utility compared to the globally optimal set using both solution algorithms. Our results are comparable to other studies illustrating the benefits of optimization for different conservation planning problems, and highlight the importance of maximizing the effectiveness of limited funding for conservation and natural resource management. PMID:25538868

Optimization in the utility maximization framework for conservation planning: a comparison of solution procedures in a study of multifunctional agriculture

USGS Publications Warehouse

Kreitler, Jason R.; Stoms, David M.; Davis, Frank W.

2014-01-01

Quantitative methods of spatial conservation prioritization have traditionally been applied to issues in conservation biology and reserve design, though their use in other types of natural resource management is growing. The utility maximization problem is one form of a covering problem where multiple criteria can represent the expected social benefits of conservation action. This approach allows flexibility with a problem formulation that is more general than typical reserve design problems, though the solution methods are very similar. However, few studies have addressed optimization in utility maximization problems for conservation planning, and the effect of solution procedure is largely unquantified. Therefore, this study mapped five criteria describing elements of multifunctional agriculture to determine a hypothetical conservation resource allocation plan for agricultural land conservation in the Central Valley of CA, USA. We compared solution procedures within the utility maximization framework to determine the difference between an open source integer programming approach and a greedy heuristic, and find gains from optimization of up to 12%. We also model land availability for conservation action as a stochastic process and determine the decline in total utility compared to the globally optimal set using both solution algorithms. Our results are comparable to other studies illustrating the benefits of optimization for different conservation planning problems, and highlight the importance of maximizing the effectiveness of limited funding for conservation and natural resource management.

Method and apparatus for determining and utilizing a time-expanded decision network

NASA Technical Reports Server (NTRS)

de Weck, Olivier (Inventor); Silver, Matthew (Inventor)

2012-01-01

A method, apparatus and computer program for determining and utilizing a time-expanded decision network is presented. A set of potential system configurations is defined. Next, switching costs are quantified to create a "static network" that captures the difficulty of switching among these configurations. A time-expanded decision network is provided by expanding the static network in time, including chance and decision nodes. Minimum cost paths through the network are evaluated under plausible operating scenarios. The set of initial design configurations are iteratively modified to exploit high-leverage switches and the process is repeated to convergence. Time-expanded decision networks are applicable, but not limited to, the design of systems, products, services and contracts.

Accurate Identification of Fatty Liver Disease in Data Warehouse Utilizing Natural Language Processing.

PubMed

Redman, Joseph S; Natarajan, Yamini; Hou, Jason K; Wang, Jingqi; Hanif, Muzammil; Feng, Hua; Kramer, Jennifer R; Desiderio, Roxanne; Xu, Hua; El-Serag, Hashem B; Kanwal, Fasiha

2017-10-01

Natural language processing is a powerful technique of machine learning capable of maximizing data extraction from complex electronic medical records. We utilized this technique to develop algorithms capable of "reading" full-text radiology reports to accurately identify the presence of fatty liver disease. Abdominal ultrasound, computerized tomography, and magnetic resonance imaging reports were retrieved from the Veterans Affairs Corporate Data Warehouse from a random national sample of 652 patients. Radiographic fatty liver disease was determined by manual review by two physicians and verified with an expert radiologist. A split validation method was utilized for algorithm development. For all three imaging modalities, the algorithms could identify fatty liver disease with >90% recall and precision, with F-measures >90%. These algorithms could be used to rapidly screen patient records to establish a large cohort to facilitate epidemiological and clinical studies and examine the clinic course and outcomes of patients with radiographic hepatic steatosis.

Determination of the smoke-plume heights with scanning lidar using alternative functions for establishing the atmospheric heterogeneity locations

Treesearch

Vladimir A. Kovalev; Alexander Petkov; Cyle Wold; Wei Min Hao

2010-01-01

Data-processing techniques for the scanning lidar data are considered that allow determining the upper and lower boundaries of the smoke plume or smoke layering in the vicinity of wildfires. The task is fulfilled by utilizing the Atmospheric Heterogeneity Height Indicator (AHHI). The AHHI is a histogram, which shows a number of heterogeneity events defined by scanning...

An Analysis of the Space Transportation System Launch Rate Capability Utilizing Q-GERT Simulation Techniques.

DTIC Science & Technology

1982-12-01

VAPE was modeled to determine this launch rate and to determine the processing times for an Orbiter at VAPe . This informa- 21 tion was then used in the...year (node 79 and activity ?1). ETa are then selected to be sent to either KSC or VAPE (node 80). This decision is made (using Ur 8) on the basis of

25 CFR 1000.69 - How can a Tribe/Consortium obtain comments or selection documents received or utilized after OSG...

Code of Federal Regulations, 2013 CFR

2013-04-01

...-DETERMINATION AND EDUCATION ACT Other Financial Assistance for Planning and Negotiation Grants for Non-BIA Programs Eligibility and Application Process § 1000.69 How can a Tribe/Consortium obtain comments or...

25 CFR 1000.69 - How can a Tribe/Consortium obtain comments or selection documents received or utilized after OSG...

Code of Federal Regulations, 2014 CFR

2014-04-01

...-DETERMINATION AND EDUCATION ACT Other Financial Assistance for Planning and Negotiation Grants for Non-BIA Programs Eligibility and Application Process § 1000.69 How can a Tribe/Consortium obtain comments or...

25 CFR 1000.69 - How can a Tribe/Consortium obtain comments or selection documents received or utilized after OSG...

Code of Federal Regulations, 2012 CFR

2012-04-01

...-DETERMINATION AND EDUCATION ACT Other Financial Assistance for Planning and Negotiation Grants for Non-BIA Programs Eligibility and Application Process § 1000.69 How can a Tribe/Consortium obtain comments or...

25 CFR 1000.69 - How can a Tribe/Consortium obtain comments or selection documents received or utilized after OSG...

Code of Federal Regulations, 2011 CFR

2011-04-01

...-DETERMINATION AND EDUCATION ACT Other Financial Assistance for Planning and Negotiation Grants for Non-BIA Programs Eligibility and Application Process § 1000.69 How can a Tribe/Consortium obtain comments or...

Automatic bio-sample bacteria detection system

NASA Technical Reports Server (NTRS)

Chappelle, E. W.; Colburn, M.; Kelbaugh, B. N.; Picciolo, G. L.

1971-01-01

Electromechanical device analyzes urine specimens in 15 minutes and processes one sample per minute. Instrument utilizes bioluminescent reaction between luciferase-luciferin mixture and adenosine triphosphate (ATP) to determine number of bacteria present in the sample. Device has potential application to analysis of other body fluids.

Administrator Evaluation--Planning and Process.

ERIC Educational Resources Information Center

Sweeney, Jim

1981-01-01

Discusses five tasks basic to effective administrator evaluation: development of district philosophy; identification of activities crucial to school success; determination of operational procedures; utilization of forms and records which reflect district philosophy; and examination of the components of the system during a trial period. (JD)

Study on the Water Resource Sustainable Utilization Evaluation Index System in Jiangsu Coast Reclamation Region

NASA Astrophysics Data System (ADS)

Ren, L.

2016-12-01

As a comprehensive system, there are many subsystems such as water resource subsystem, social subsystem, economic subsystem and ecological subsystem in water resource sustainable utilization system. In this paper, an evaluation system including three levels is set up according to the metric demands of sustainable water resource utilization in Jiangsu coast reclamation region, namely the target level, the rule level, and the index level. Considering the large number of the indexes, the analytic hierarchy process is used to determine the weights of all these subsystems in the total goal of water sustainable utilization. By analyzing these weights, the attributes of water resource itself is found to be the most important aspect for the evaluation of sustainable utilization in Jiangsu coast reclamation region, and the second important aspect is the situation of the eco-environment.

Applying Parallel Processing Techniques to Tether Dynamics Simulation

NASA Technical Reports Server (NTRS)

Wells, B. Earl

1996-01-01

The focus of this research has been to determine the effectiveness of applying parallel processing techniques to a sizable real-world problem, the simulation of the dynamics associated with a tether which connects two objects in low earth orbit, and to explore the degree to which the parallelization process can be automated through the creation of new software tools. The goal has been to utilize this specific application problem as a base to develop more generally applicable techniques.

Fabrication process scale-up and optimization for a boron-aluminum composite radiator

NASA Technical Reports Server (NTRS)

Okelly, K. P.

1973-01-01

Design approaches to a practical utilization of a boron-aluminum radiator for the space shuttle orbiter are presented. The program includes studies of laboratory composite material processes to determine the feasibility of a structural and functional composite radiator panel, and to estimate the cost of its fabrication. The objective is the incorporation of boron-aluminum modulator radiator on the space shuttle.

Guideline for assessing the performance of electric power systems in natural hazard and human threat events

USGS Publications Warehouse

Savage, W.U.; Nishenko, S.P.; Honegger, D.G.; Kempner, L.

2006-01-01

Electric power utilities are familiar with and skilled in preparing for and responding to almost-routine natural hazard events such as strong wind and ice storms and seasonal floods, as well as intentional human acts such as vandalism. Recent extreme weather (hurricanes Katrina and Rita), extremely destructive international earthquakes (in Sumatra and Pakistan), and nation-wide concerns regarding future terrorist attacks have increased the pressure on utilities to take appropriate steps to avoid being overwhelmed by such infrequent and exceedingly severe events. Determining what constitutes the appropriate steps to take requires various levels of understanding of the specific hazards and the risks faced by the utility. The American Lifelines Alliance (www. americanlifelinesalliance.org) has prepared a Guideline that provides clear, concise, and nationally-applicable guidance on determining the scope and level of effort necessary to assess power system performance in the wide range of natural hazard or human threat events. Included in this Guideline are specific procedures to follow and information to consider in performing standardized assessments. With the results of such assessments, utility owners can effectively establish and carry out risk management programs that will lead to achieving appropriate levels of performance in future events. The Guideline incorporates an inquiry-driven process with a two-phase performance assessment that can be applied to power systems of any size. The screening phase enables systems or components that are clearly not at risk to be screened out early. The subsequent analysis phase uses results from the screening phase to prioritize and allocate resources for more detailed assessments of hazard, vulnerability, and system performance. This process helps assure that the scope of the assessment meets the specific performance objectives of the inquiry. A case history is presented to illustrate the type of experience with an inquiry-driven process that was considered in developing the Guideline to meet the diverse needs of utility personnel in engineering, operations, and management. Copyright ASCE 2007.

Role of vegetation and edaphic factors in controlling diversity and use of different carbon sources in semi-arid ecosystems

NASA Astrophysics Data System (ADS)

Lohse, K. A.; McLain, J. E.; Harman, C. J.; Sivapalan, M.; Troch, P. A.

2010-12-01

Microbially-mediated soil carbon cycling is closely linked to soil moisture and temperature. Climate change is predicted to increase intra-annual precipitation variability (i.e. less frequent yet more intense precipitation events) and alter biogeochemical processes due to shifts in soil moisture dynamics and inputs of carbon. However, the responses of soil biology and chemistry to predicted climate change, and their concomitant feedbacks on ecosystem productivity and biogeochemical processes are poorly understood. We collected soils at three different elevations in the Santa Catalina Mountains, AZ and quantified carbon utilization during pre-monsoon precipitation conditions. Contrasting parent materials (schist and granite) were paired at each elevation. We expected climate to determine the overall activity of soil fungal and bacterial communities and diversity of soil C utilization, and differences in parent material to modify these responses through controls on soil physical properties. We used EcoPlateTM C utilization assays to determine the relative abundance of soil bacterial and fungal populations and rate and diversity of carbon utilization. Additional plates were incubated with inhibitors selective to fungal or bacterial activity to assess relative contribution of these microbial groups to overall C utilization. We analyzed soils for soil organic matter, total C and N, particle size analysis and soil moisture content via both gravimetric and volumetric methods to assess the influences of soil physical and chemical properties on the measured biological responses. Consistent with our expectations, overall microbial activity was highest at the uppermost conifer elevation sites compared to the middle and lower elevation sites. In contrast to our expectations, however, overall activity was lower at the mid elevation oak woodland sites compared to the low elevation desert sites. Also consistent with our expectations was the observation that overall activities were consistently higher in schist parent material compared to granite. Though differences between canopy and intercanopy carbon utilization were subtle, the diversity of carbon utilization differed, suggesting a potential role of root exudates in governing C utilization in these semiarid soils. Findings from this study suggest that soil physical properties due to parent material have primary impacts in constraining microbial growth and carbon utilization under changing climate conditions.

Colossal Tooling Design: 3D Simulation for Ergonomic Analysis

NASA Technical Reports Server (NTRS)

Hunter, Steve L.; Dischinger, Charles; Thomas, Robert E.; Babai, Majid

2003-01-01

The application of high-level 3D simulation software to the design phase of colossal mandrel tooling for composite aerospace fuel tanks was accomplished to discover and resolve safety and human engineering problems. The analyses were conducted to determine safety, ergonomic and human engineering aspects of the disassembly process of the fuel tank composite shell mandrel. Three-dimensional graphics high-level software, incorporating various ergonomic analysis algorithms, was utilized to determine if the process was within safety and health boundaries for the workers carrying out these tasks. In addition, the graphical software was extremely helpful in the identification of material handling equipment and devices for the mandrel tooling assembly/disassembly process.

Computed Tomography and Thermography Increases CMC Material and Process Development Efficiency and Testing Effectiveness

NASA Technical Reports Server (NTRS)

Effinger, Michael; Beshears, Ron; Hufnagle, David; Walker, James; Russell, Sam; Stowell, Bob; Myers, David

2002-01-01

Nondestructive characterization techniques have been used to steer development and testing of CMCs. Computed tomography is used to determine the volumetric integrity of the CMC plates and components. Thermography is used to determine the near surface integrity of the CMC plates and components. For process and material development, information such as density uniformity, part delamination, and dimensional tolerance conformity is generated. The information from the thermography and computed tomography is correlated and then specimen cutting maps are superimposed on the thermography images. This enables for tighter data and potential explanation of off nominal test data. Examples of nondestructive characterization utilization to make decisions in process and material development and testing are presented.

Ultrasonic tomography for in-process measurements of temperature in a multi-phase medium

DOEpatents

Beller, Laurence S.

1993-01-01

A method and apparatus for the in-process measurement of internal particulate temperature utilizing ultrasonic tomography techniques to determine the speed of sound through a specimen material. Ultrasonic pulses are transmitted through a material, which can be a multi-phase material, over known flight paths and the ultrasonic pulse transit times through all sectors of the specimen are measured to determine the speed of sound. The speed of sound being a function of temperature, it is possible to establish the correlation between speed of sound and temperature, throughout a cross-section of the material, which correlation is programmed into a computer to provide for a continuous in-process measurement of temperature throughout the specimen.

Social determinants of bone densitometry uptake for osteoporosis risk in patients aged 50yr and older: a systematic review.

PubMed

Brennan, Sharon L; Wluka, Anita E; Gould, Haslinda; Nicholson, Geoffrey C; Leslie, William D; Ebeling, Peter R; Oldenburg, Brian; Kotowicz, Mark A; Pasco, Julie A

2012-01-01

The World Health Organization identifies that osteoporosis is one of the leading health problems in the Western world. An increased risk of fragility fracture is observed in more socially disadvantaged individuals in most Western countries. Dual-energy X-ray absorptiometry (DXA) is currently the procedure of choice to diagnose osteoporosis and assess fracture risk. We systematically reviewed the literature regarding social determinants of DXA utilization for osteoporosis detection in patients aged 50yr and older using a computer-aided search of MEDLINE, EMBASE, CINAHL, and PsychINFO from January 1994 to December 2010. Five cross-sectional studies, incorporating 16 separate analyses, were identified for inclusion in this review. The best evidence analysis identified limited evidence for a positive association between either income or education with DXA utilization; furthermore, the best evidence analysis found no evidence for an association between either marital status or working status and DXA utilization. Further research is required to identify whether a relationship exists and elucidate reasons for disparities in DXA utilization between different social groups, such as choice and referral processes, as a necessary precursor in identifying modifiable determinants and appropriate strategies to promote preventive screening to identify fracture risk. Copyright © 2012 The International Society for Clinical Densitometry. Published by Elsevier Inc. All rights reserved.

Analysis of methanogenic activity in a thermophilic-dry anaerobic reactor: use of fluorescent in situ hybridization.

PubMed

Montero, B; García-Morales, J L; Sales, D; Solera, R

2009-03-01

Methanogenic activity in a thermophilic-dry anaerobic reactor was determined by comparing the amount of methane generated for each of the organic loading rates with the size of the total and specific methanogenic population, as determined by fluorescent in situ hybridization. A high correlation was evident between the total methanogenic activity and retention time [-0.6988Ln(x)+2.667] (R(2) 0.8866). The total methanogenic activity increased from 0.04x10(-8) mLCH(4) cell(-1)day(-1) to 0.38x10(-8) mLCH(4) cell(-1)day(-1) while the retention time decreased, augmenting the organic loading rates. The specific methanogenic activities of H(2)-utilizing methanogens and acetate-utilizing methanogens increased until they stabilised at 0.64x10(-8) mLCH(4) cell(-1)day(-1) and 0.33x10(-8) mLCH(4) cell(-1)day(-1), respectively. The methanogenic activity of H(2)-utilizing methanogens was higher than acetate-utilizing methanogens, indicating that maintaining a low partial pressure of hydrogen does not inhibit the acetoclastic methanogenesis or the anaerobic process.

Validation of the conceptual research utilization scale: an application of the standards for educational and psychological testing in healthcare.

PubMed

Squires, Janet E; Estabrooks, Carole A; Newburn-Cook, Christine V; Gierl, Mark

2011-05-19

There is a lack of acceptable, reliable, and valid survey instruments to measure conceptual research utilization (CRU). In this study, we investigated the psychometric properties of a newly developed scale (the CRU Scale). We used the Standards for Educational and Psychological Testing as a validation framework to assess four sources of validity evidence: content, response processes, internal structure, and relations to other variables. A panel of nine international research utilization experts performed a formal content validity assessment. To determine response process validity, we conducted a series of one-on-one scale administration sessions with 10 healthcare aides. Internal structure and relations to other variables validity was examined using CRU Scale response data from a sample of 707 healthcare aides working in 30 urban Canadian nursing homes. Principal components analysis and confirmatory factor analyses were conducted to determine internal structure. Relations to other variables were examined using: (1) bivariate correlations; (2) change in mean values of CRU with increasing levels of other kinds of research utilization; and (3) multivariate linear regression. Content validity index scores for the five items ranged from 0.55 to 1.00. The principal components analysis predicted a 5-item 1-factor model. This was inconsistent with the findings from the confirmatory factor analysis, which showed best fit for a 4-item 1-factor model. Bivariate associations between CRU and other kinds of research utilization were statistically significant (p < 0.01) for the latent CRU scale score and all five CRU items. The CRU scale score was also shown to be significant predictor of overall research utilization in multivariate linear regression. The CRU scale showed acceptable initial psychometric properties with respect to responses from healthcare aides in nursing homes. Based on our validity, reliability, and acceptability analyses, we recommend using a reduced (four-item) version of the CRU scale to yield sound assessments of CRU by healthcare aides. Refinement to the wording of one item is also needed. Planned future research will include: latent scale scoring, identification of variables that predict and are outcomes to conceptual research use, and longitudinal work to determine CRU Scale sensitivity to change.

A Genome Sequence-directed Investigation of D-Tagatose Utilization by Kosmotoga Olearia

NASA Astrophysics Data System (ADS)

Butzin, N. C.; Bradnan, D. M.; Noll, K. M.

2010-04-01

The research goals are to determine the pathway that Kosmotoga olearia uses tagatose, the roles of Kole_0686, Kole_0737 and Kole_1652 in this process, and the evolutionary history of the genes that encode the proteins involved in tagatose catabolism.

Strategic plan to optimize the management of right-of-way parcel and utility information at FDOT.

DOT National Transportation Integrated Search

2013-05-01

The Florida Department of Transportation (FDOT) manages a huge right-of-way asset. Examples of core : processes related to this asset include determining right-of-way boundaries; inventorying roadside features; : preparing right-of-way maps; acquirin...

Development of a validation process for parameters utilized in optimizing construction quality management of pavements.

DOT National Transportation Integrated Search

2006-01-01

The implementation of an effective performance-based construction quality management requires a tool for determining impacts of construction quality on the life-cycle performance of pavements. This report presents an update on the efforts in the deve...

Evaluating Cumulative Ascent:. Mountain Biking Meets Mandelbrot

NASA Astrophysics Data System (ADS)

Rapaport, D. C.

The problem of determining total distance ascended during a mountain bike trip is addressed. Altitude measurements are obtained from GPS receivers utilizing both GPS-based and barometric altitude data, with data averaging used to reduce fluctuations. The estimation process is sensitive to the degree of averaging, and is related to the well-known question of determining coastline length. Barometric-based measurements prove more reliable, due to their insensitivity to GPS altitude fluctuations.

[Applications of near infrared reflectance spectroscopy technique to determination of forage mycotoxins].

PubMed

Xu, Qing-Fang; Han, Jian-Guo; Yu, Zhu; Yue, Wen-Bin

2010-05-01

The near infrared reflectance spectroscopy technique (NIRS) has been explored at many fields such as agriculture, food, chemical, medicine, and so on, due to its rapid, effective, non-destructive, and on-line characteristics. Fungi invasion in forage materials during processing and storage would generate mycotoxins, which were harmful for people and animal through food chains. The determination of mycotoxins included the overelaborated pretreatments such as milling, extracting, chromatography and subsequent process such as enzyme linked immunosorbent assay, high performance liquid chromatography, and thin layer chromatography. The authors hope that high precision and low detection limit spectrum instrument, and software technology and calibration model of mycotoxins determination, will fast measure accurately the quality and quantity of mycotoxins, which will provide basis for reasonable process and utilization of forage and promote the application of NIRS in the safety livestock product.

Age determination by teeth examination: a comparison between different morphologic and quantitative analyses.

PubMed

Amariti, M L; Restori, M; De Ferrari, F; Paganelli, C; Faglia, R; Legnani, G

1999-06-01

Age determination by teeth examination is one of the main means of determining personal identification. Current studies have suggested different techniques for determining the age of a subject by means of the analysis of microscopic and macroscopic structural modifications of the tooth with ageing. The histological approach is useful among the various methodologies utilized for this purpose. It is still unclear as to what is the best technique, as almost all the authors suggest the use of the approach they themselves have tested. In the present study, age determination by means of microscopic techniques has been based on the quantitative analysis of three parameters, all well recognized in specialized literature: 1. dentinal tubules density/sclerosis 2. tooth translucency 3. analysis of the cementum thickness. After a description of the three methodologies (with automatic image processing of the dentinal sclerosis utilizing an appropriate computer program developed by the authors) the results obtained on cases using the three different approaches are presented, and the merits and failings of each technique are identified with the intention of identifying the one offering the least degree of error in age determination.

Risky Decision in Depression: Sad Schemas Produce Unexpected Utility Values.

ERIC Educational Resources Information Center

Hartman, David E.; McKirnan, David J.

Recent models of depression have shown differences in information processing to be important concomitants of depressed affect. To determine whether the cognitive distortion found in depressed individuals extends beyond self-evaluation and interpersonal evaluation into abstract decision making, 288 college students completed the Beck Depression…

Antioxidant Extraction and Biogas Production from Pomegranate Marc

USDA-ARS?s Scientific Manuscript database

The pomegranate marc (PM), by-product from pomegranate juice processing, has not been effectively utilized. The objectives of this study were to (1) determine the yields and properties of antioxidants (total phenolics) extracted from peels and seeds of pomegranate marc in wet and dry forms, and (2)...

Development of Advanced Coatings for Laser Modifications Through Process and Materials Simulation

NASA Astrophysics Data System (ADS)

Martukanitz, R. P.; Babu, S. S.

2004-06-01

A simulation-based system is currently being constructed to aid in the development of advanced coating systems for laser cladding and surface alloying. The system employs loosely coupled material and process models that allow rapid determination of material compatibility over a wide range of processing conditions. The primary emphasis is on the development and identification of composite coatings for improved wear and corrosion resistance. The material model utilizes computational thermodynamics and kinetic analysis to establish phase stability and extent of diffusional reactions that may result from the thermal response of the material during virtual processing. The process model is used to develop accurate thermal histories associated with the laser surface modification process and provides critical input for the non-isothermal materials simulations. These techniques were utilized to design a laser surface modification experiment that utilized the addition of stainless steel alloy 431 and TiC produced using argon and argon and nitrogen shielding. The deposits representing alloy 431 and TiC powder produced in argon resulted in microstructures retaining some TiC particles and an increase in hardness when compared to deposits produced using only the 431 powder. Laser deposits representing alloy 431 and TiC powder produced with a mixture of argon and nitrogen shielding gas resulted in microstructures retaining some TiC particles, as well as fine precipitates of Ti(CN) formed during cooling and a further increase in hardness of the deposit.

77 FR 9179 - Medicare Program; Reporting and Returning of Overpayments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-16

...'s name, number and tax identification number; and the date of service. The voluntary refund process... reporting form include: (1) Accountants and auditors (external and in-house); and (2) miscellaneous in-house... accountant). Consequently, in order to determine the burden cost, we utilize the average hourly wage of these...

COMPARISON OF PARTICLE SIZE DISTRIBUTIONS AND ELEMENTAL PARTITIONING FROM THE COMBUSTION OF PULVERIZED COAL AND RESIDUAL FUEL OIL

EPA Science Inventory

The paper gives results of experimental efforts in which three coals and a residual fuel oil were combusted in three different systems simulating process and utility boilers. Particloe size distributions (PSDs) were determined using atmospheric and low-pressure impaction, electr...

BIOWINOL TECHNOLOGIES: A HYBRID GREEN PROCESS FOR BIOFUEL PRODUCTION

EPA Science Inventory

The ability of the unique bacteria to produce ethanol by utilizing H₂ and CO₂ will be determined. The project will be used to educate the community about advances and importance of bioenergy while building consumer confidence in biofuels in addressing...

Utilization of non-conventional systems for conversion of biomass to food components: Potential for utilization of algae in engineered foods

NASA Technical Reports Server (NTRS)

Karel, M.; Kamarei, A. R.; Nakhost, Z.

1985-01-01

The major nutritional components of the green algae (Scenedesmus obliquus) grown in a Constant Cell density Apparatus were determined. Suitable methodology to prepare proteins from which three major undesirable components of these cells (i.e., cell walls, nucleic acids, and pigments) were either removed or substantially reduced was developed. Results showed that processing of green algae to protein isolate enhances its potential nutritional and organoleptic acceptability as a diet component in a Controlled Ecological Life Support System.

Medicare Program; Prior Authorization Process for Certain Durable Medical Equipment, Prosthetics, Orthotics, and Supplies. Final rule.

PubMed

2015-12-30

This final rule establishes a prior authorization program for certain durable medical equipment, prosthetics, orthotics, and supplies (DMEPOS) items that are frequently subject to unnecessary utilization. This rule defines unnecessary utilization and creates a new requirement that claims for certain DMEPOS items must have an associated provisional affirmed prior authorization decision as a condition of payment. This rule also adds the review contractor's decision regarding prior authorization of coverage of DMEPOS items to the list of actions that are not initial determinations and therefore not appealable.

Time Shifted PN Codes for CW Lidar, Radar, and Sonar

NASA Technical Reports Server (NTRS)

Campbell, Joel F. (Inventor); Prasad, Narasimha S. (Inventor); Harrison, Fenton W. (Inventor); Flood, Michael A. (Inventor)

2013-01-01

A continuous wave Light Detection and Ranging (CW LiDAR) system utilizes two or more laser frequencies and time or range shifted pseudorandom noise (PN) codes to discriminate between the laser frequencies. The performance of these codes can be improved by subtracting out the bias before processing. The CW LiDAR system may be mounted to an artificial satellite orbiting the earth, and the relative strength of the return signal for each frequency can be utilized to determine the concentration of selected gases or other substances in the atmosphere.

Review of R and D on Water Hyacinth Utilization in the Philippine Republic

NASA Technical Reports Server (NTRS)

Otis, J. L.; Hillman, M. E. D.

1976-01-01

The operations of a Filipino inventor were observed with a view toward determining the technical-economic potential of his hyacinth utilization concepts if the highly fibrous portion of the plant were separated from the other components. Subjects of particular interest include: (1) water hyacinth harvesting techniques, volumes and costs; (2) hyacinth defibering processes; and (3) uses of hyacinth materials for production of animal feeds, paper fibers, particle boards, acoustic and insulation boards, various vitamins and minerals (especially Vitamin A), food products, pesticides, and medicinal and pharmaceutical products.

Utilizing dynamic laser speckle to probe nanoscale morphology evolution in nanoporous gold thin films

DOE PAGES

Chapman, Christopher A. R.; Ly, Sonny; Wang, Ling; ...

2016-03-02

Here we show the use of dynamic laser speckle autocorrelation spectroscopy in conjunction with the photothermal treatment of nanoporous gold (np-Au) thin films to probe nanoscale morphology changes during the photothermal treatment. Utilizing this spectroscopy method, backscattered speckle from the incident laser is tracked during photothermal treatment and both the characteristic feature size and annealing time of the film are determined. These results demonstrate that this method can successfully be used to monitor laser-based surface modification processes without the use of ex-situ characterization.

Modulated Sine Waves for Differential Absorption Measurements Using a CW Laser System

NASA Technical Reports Server (NTRS)

Campbell, Joel F. (Inventor); Lin, Bing (Inventor); Nehrir, Amin R. (Inventor)

2015-01-01

A continuous wave Light Detection and Ranging (CW LiDAR) system utilizes two or more laser frequencies and time or range shifted pseudorandom noise (PN) codes to discriminate between the laser frequencies. The performance of these codes can be improved by subtracting out the bias before processing. The CW LiDAR system may be mounted to an artificial satellite orbiting the earth, and the relative strength of the return signal for each frequency can be utilized to determine the concentration of selected gases or other substances in the atmosphere.

Utilizing dynamic laser speckle to probe nanoscale morphology evolution in nanoporous gold thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chapman, Christopher A. R.; Ly, Sonny; Wang, Ling

Here we show the use of dynamic laser speckle autocorrelation spectroscopy in conjunction with the photothermal treatment of nanoporous gold (np-Au) thin films to probe nanoscale morphology changes during the photothermal treatment. Utilizing this spectroscopy method, backscattered speckle from the incident laser is tracked during photothermal treatment and both the characteristic feature size and annealing time of the film are determined. These results demonstrate that this method can successfully be used to monitor laser-based surface modification processes without the use of ex-situ characterization.

Clinic to Cockpit: Analysis of Aviator Grounding Periods Due to Psychiatric Disorders

DTIC Science & Technology

2018-06-01

The process to return U.S. Air Force aviators to flying status due to psychiatric conditions involves multiple parties and can be lengthy. We...examined grounding periods in a sample of aircrew to determine the causes of grounded time and to explore possible improvement in the waiver system. The...authors examined aeromedical records of 41 aviators treated with antidepressant medication to determine three metrics: total days grounded, days utilized

Analysis of the fly ash from the processing of wood chips in a pilot-scale downdraft gasifier: Comparison of inorganic constituents determined by PIXE and ICP-AES

Treesearch

Thomas L Eberhardt; Hui Pan

2013-01-01

Gasification of biomass ultimately generates at least one solid byproduct in which the inorganic constituents of the biomass are concentrated. Given the potential for utilization, or issues with disposal, facile methods are needed for determining the compositions of the fly ashes from recently-available gasifier-based bioenergy systems. Proton induced x-ray emission...

The Effects of Voltage and Concentration of Sodium Bicarbonate on Electrochemical Synthesis of Ethanol from Carbon Dioxide Using Brass as Cathode

NASA Astrophysics Data System (ADS)

Ramadan, Septian; Fariduddin, Sholah; Rizki Aminudin, Afianti; Kurnia Hayatri, Antisa; Riyanto

2017-11-01

The effects of voltage and concentration of sodium bicarbonate were investigated to determine the optimum conditions of the electrochemical synthesis process to convert carbon dioxide into ethanol. The conversion process is carried out using a sodium bicarbonate electrolyte solution in an electrochemical synthesis reactor equipped with a cathode and anode. As the cathode was used brass, while as the anode carbon was utilized. Sample of the electrochemical synthesis process was analyzed by gas chromatography to determine the content of the compounds produced. The optimum electrochemical synthesis conditions to convert carbon dioxide into ethanol are voltage and concentration of sodium bicarbonate are 3 volts and 0.4 M with ethanol concentration of 1.33%.

Methods and systems for detection of radionuclides

DOEpatents

Coates, Jr., John T.; DeVol, Timothy A.

2010-05-25

Disclosed are materials and systems useful in determining the existence of radionuclides in an aqueous sample. The materials provide the dual function of both extraction and scintillation to the systems. The systems can be both portable and simple to use, and as such can beneficially be utilized to determine presence and optionally concentration of radionuclide contamination in an aqueous sample at any desired location and according to a relatively simple process without the necessity of complicated sample handling techniques. The disclosed systems include a one-step process, providing simultaneous extraction and detection capability, and a two-step process, providing a first extraction step that can be carried out in a remote field location, followed by a second detection step that can be carried out in a different location.

Ultrasonic tomography for in-process measurements of temperature in a multi-phase medium

DOEpatents

Beller, L.S.

1993-01-26

A method and apparatus are described for the in-process measurement of internal particulate temperature utilizing ultrasonic tomography techniques to determine the speed of sound through a specimen material. Ultrasonic pulses are transmitted through a material, which can be a multi-phase material, over known flight paths and the ultrasonic pulse transit times through all sectors of the specimen are measured to determine the speed of sound. The speed of sound being a function of temperature, it is possible to establish the correlation between speed of sound and temperature, throughout a cross-section of the material, which correlation is programmed into a computer to provide for a continuous in-process measurement of temperature throughout the specimen.

Utility of action checklists as a consensus building tool

PubMed Central

KIM, Yeon-Ha; YOSHIKAWA, Etsuko; YOSHIKAWA, Toru; KOGI, Kazutaka; JUNG, Moon-Hee

2014-01-01

The present study’s objective was to determine the mechanisms for enhancing the utility of action checklists applied in participatory approach programs for workplace improvements, to identify the benefits of building consensus and to compare their applicability in Asian countries to find the most appropriate configuration for action checklists. Data were collected from eight trainees and 43 trainers with experience in Participatory Action-Oriented Training. Statistical analysis was performed in SPSS using the package PASW, version 19.0. The difference in the mean score for the degree of the utility of action checklists between countries was analyzed using ANOVA methods. Factor analysis was performed to validate the action checklists’ utility. Pearson Correlation Coefficients were then calculated to determine the direction and strength of the relationship between these factors. Using responses obtained from trainees’ in-depth interviews, we identified 33 key statements that were then classified into 11 thematic clusters. Five factors were extracted, namely “ease of application”, “practical solutions”, “group interaction”, “multifaceted perspective” and “active involvement”. The action checklist was useful for facilitating a participatory process among trainees and trainers for improving working conditions. Action checklists showed similar patterns of utility in various Asian countries; particularly when adjusted to local conditions. PMID:25224334

FTR GO14246

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bentley, Martha

2008-06-30

The Maine Forest Bioproducts Research and Development project originally focused on the State’s interest in the development of an integrated forest products refinery (IFPR). The original intent was that Research and Development (R&D) funded by this award will allow Maine to refine its strategy and pursue development of an integrated biorefinery. Activities were to be divided into three major R&D projects: (a) Establish the potential for a forest products biorefinery in Maine, by determining the technical and economic feasibility and resource availability. (b) Investigate and develop conversion processes for forest bioproducts to utilize the sugars available from hemicellulose. Research projectsmore » will determine how to best utilize refinery waste streams to recover heat value and recycle remaining components. (c) Cost share very early stage R&D efforts to engage the private sector and stimulate innovative efforts that will build upon the research efforts in (b) above, utilize the information gleaned from (a), and lead to commercialization of new products or services and development of the forest bioproducts industrial sector in Maine.« less

Assessment of MSFCs Process for the Development and Activation of Space Act Agreement

NASA Technical Reports Server (NTRS)

Daugherty, Rachel

2014-01-01

Space Act Agreements (SAAs) are contractual agreements that NASA utilizes to form partnerships with researchers, industry, and academia to stimulate cutting-edge innovation within the science and technology communities. center dot This study assessed the current SAA development and activation process at Marshall Space Flight Center (MSFC) to determine if improvements could be implemented to increase productivity, decrease time to activation, and improve the quality of deliverables.

Analysis of edible oil processing options for the BIO-Plex advanced life support system

NASA Technical Reports Server (NTRS)

Greenwalt, C. J.; Hunter, J.

2000-01-01

Edible oil is a critical component of the proposed plant-based Advanced Life Support (ALS) diet. Soybean, peanut, and single-cell oil are the oil source options to date. In terrestrial manufacture, oil is ordinarily extracted with hexane, an organic solvent. However, exposed solvents are not permitted in the spacecraft environment or in enclosed human tests by National Aeronautics and Space Administration due to their potential danger and handling difficulty. As a result, alternative oil-processing methods will need to be utilized. Preparation and recovery options include traditional dehulling, crushing, conditioning, and flaking, extrusion, pressing, water extraction, and supercritical extraction. These processing options were evaluated on criteria appropriate to the Advanced Life Support System and BIO-Plex application including: product quality, product stability, waste production, risk, energy needs, labor requirements, utilization of nonrenewable resources, usefulness of by-products, and versatility and mass of equipment to determine the most appropriate ALS edible oil-processing operation.

Overhead longwave infrared hyperspectral material identification using radiometric models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zelinski, M. E.

Material detection algorithms used in hyperspectral data processing are computationally efficient but can produce relatively high numbers of false positives. Material identification performed as a secondary processing step on detected pixels can help separate true and false positives. This paper presents a material identification processing chain for longwave infrared hyperspectral data of solid materials collected from airborne platforms. The algorithms utilize unwhitened radiance data and an iterative algorithm that determines the temperature, humidity, and ozone of the atmospheric profile. Pixel unmixing is done using constrained linear regression and Bayesian Information Criteria for model selection. The resulting product includes an optimalmore » atmospheric profile and full radiance material model that includes material temperature, abundance values, and several fit statistics. A logistic regression method utilizing all model parameters to improve identification is also presented. This paper details the processing chain and provides justification for the algorithms used. Several examples are provided using modeled data at different noise levels.« less

Chiral Determination of Amino Acids Using X-Ray Diffraction of Thin Films

NASA Technical Reports Server (NTRS)

Dragoi, D.; Kulleck, J.; Kanik, I.; Beegle, L. W.

2003-01-01

The astrobiological search for life, both extinct and extant, on other solar system bodies will take place via several planned lander missions to Mars Europa and Titan. The detection and identification of organic molecules that have been associated with life is a major technical challenge. Terrestrial life utilizes organic molecules, such as amino acids, as its basic building block. Amino acids can be synthesized by natural processes as is demonstrated by their detection in meteoritic material. In this process, the organic molecules are produced roughly in a even mixture of D and L forms. Biological process, however, can utilize almost uniquely one form or the other. In terrestrial biology, only the L-amino acids is common in biological processes. If signature of life existed elsewhere in the D form it then be concluded that life had evolutionary beginning on that body. Detection of an enantiomeric excess of L over D would also be a powerful sign that life had existed on that body at one time.

Technology and development requirements for advanced coal conversion systems

NASA Technical Reports Server (NTRS)

1981-01-01

A compendium of coal conversion process descriptions is presented. The SRS and MC data bases were utilized to provide information paticularly in the areas of existing process designs and process evaluations. Additional information requirements were established and arrangements were made to visit process developers, pilot plants, and process development units to obtain information that was not otherwise available. Plant designs, process descriptions and operating conditions, and performance characteristics were analyzed and requirements for further development identified and evaluated to determine the impact of these requirements on the process commercialization potential from the standpoint of economics and technical feasibility. A preliminary methodology was established for the comparative technical and economic assessment of advanced processes.

Load research manual. Volume 1. Load research procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandenburg, L.; Clarkson, G.; Grund, Jr., C.

1980-11-01

This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussedmore » in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.« less

Hot topics: Signal processing in acoustics

NASA Astrophysics Data System (ADS)

Gaumond, Charles F.

2005-09-01

Signal processing in acoustics is a multidisciplinary group of people that work in many areas of acoustics. We have chosen two areas that have shown exciting new applications of signal processing to acoustics or have shown exciting and important results from the use of signal processing. In this session, two hot topics are shown: the use of noiselike acoustic fields to determine sound propagation structure and the use of localization to determine animal behaviors. The first topic shows the application of correlation on geo-acoustic fields to determine the Greens function for propagation through the Earth. These results can then be further used to solve geo-acoustic inverse problems. The first topic also shows the application of correlation using oceanic noise fields to determine the Greens function through the ocean. These results also have utility for oceanic inverse problems. The second topic shows exciting results from the detection, localization, and tracking of marine mammals by two different groups. Results from detection and localization of bullfrogs are shown, too. Each of these studies contributed to the knowledge of animal behavior. [Work supported by ONR.

Fabrication of polymer electrolyte membrane fuel cell MEAs utilizing inkjet print technology

NASA Astrophysics Data System (ADS)

Towne, Silas; Viswanathan, Vish; Holbery, James; Rieke, Peter

Utilizing drop-on-demand technology, we have successfully fabricated hydrogen-air polymer electrolyte membrane fuel cells (PEMFC), demonstrated some of the processing advantages of this technology and have demonstrated that the performance is comparable to conventionally fabricated membrane electrode assemblies (MEAs). Commercial desktop inkjet printers were used to deposit the active catalyst electrode layer directly from print cartridges onto Nafion ® polymer membranes in the hydrogen form. The layers were well-adhered and withstood simple tape peel, bending and abrasion tests and did so without any post-deposition hot press step. The elimination of this processing step suggests that inkjet-based fabrication or similar processing technologies may provide a route to less expensive large-scale fabrication of PEMFCs. When tested in our experimental apparatus, open circuit voltages up to 0.87 V and power densities of up to 155 mW cm -2 were obtained with a catalyst loading of 0.20 mg Pt cm -2. A commercially available membrane under identical, albeit not optimized test conditions, showed about 7% greater power density. The objective of this work was to demonstrate some of the processing advantages of drop-on-demand technology for fabrication of MEAs. It remains to be determined if inkjet fabrication offers performance advantages or leads to more efficient utilization of expensive catalyst materials.

A technical analysis for cogeneration systems with potential applications in twelve California industrial plants. [energy saving heat-electricity utility systems

NASA Technical Reports Server (NTRS)

Moretti, V. C.; Davis, H. S.; Slonski, M. L.

1978-01-01

In a study sponsored by the State of California Energy Resources Conservation and Development Commission, 12 industrial plants in five utility districts were surveyed to assess the potential applications of the cogeneration of heat and electricity in California industry. Thermodynamic calculations were made for each plant in determining the energy required to meet the existing electrical and steam demands. The present systems were then compared to conceptual cogeneration systems specified for each plant. Overall energy savings were determined for the cogeneration applications. Steam and gas turbine topping cycle systems were considered as well as bottoming cycle systems. Types of industries studied were: pulp and paper, timber, cement, petroleum refining, enhanced oil recovery, foods processing, steel and glass

Method for conducting electroless metal-plating processes

DOEpatents

Petit, George S.; Wright, Ralph R.

1978-01-01

This invention is an improved method for conducting electroless metal-plating processes in a metal tank which is exposed to the plating bath. The invention solves a problem commonly encountered in such processes: how to determine when it is advisable to shutdown the process in order to clean and/or re-passivate the tank. The new method comprises contacting the bath with a current-conducting, non-catalytic probe and, during plating operations, monitoring the gradually changing difference in electropotential between the probe and tank. It has been found that the value of this voltage is indicative of the extent to which nickel-bearing decomposition products accumulate on the tank. By utilizing the voltage to determine when shutdown for cleaning is advisable, the operator can avoid premature shutdown and at the same time avoid prolonging operations to the point that spontaneous decomposition occurs.

A method for determining the weak statistical stationarity of a random process

NASA Technical Reports Server (NTRS)

Sadeh, W. Z.; Koper, C. A., Jr.

1978-01-01

A method for determining the weak statistical stationarity of a random process is presented. The core of this testing procedure consists of generating an equivalent ensemble which approximates a true ensemble. Formation of an equivalent ensemble is accomplished through segmenting a sufficiently long time history of a random process into equal, finite, and statistically independent sample records. The weak statistical stationarity is ascertained based on the time invariance of the equivalent-ensemble averages. Comparison of these averages with their corresponding time averages over a single sample record leads to a heuristic estimate of the ergodicity of a random process. Specific variance tests are introduced for evaluating the statistical independence of the sample records, the time invariance of the equivalent-ensemble autocorrelations, and the ergodicity. Examination and substantiation of these procedures were conducted utilizing turbulent velocity signals.

Activity-based costs of blood transfusions in surgical patients at four hospitals.

PubMed

Shander, Aryeh; Hofmann, Axel; Ozawa, Sherri; Theusinger, Oliver M; Gombotz, Hans; Spahn, Donat R

2010-04-01

Blood utilization has long been suspected to consume more health care resources than previously reported. Incomplete accounting for blood costs has the potential to misdirect programmatic decision making by health care systems. Determining the cost of supplying patients with blood transfusions requires an in-depth examination of the complex array of activities surrounding the decision to transfuse. To accurately determine the cost of blood in a surgical population from a health system perspective, an activity-based costing (ABC) model was constructed. Tasks and resource consumption (materials, labor, third-party services, capital) related to blood administration were identified prospectively at two US and two European hospitals. Process frequency (i.e., usage) data were captured retrospectively from each hospital and used to populate the ABC model. All major process steps, staff, and consumables to provide red blood cell (RBC) transfusions to surgical patients, including usage frequencies, and direct and indirect overhead costs contributed to per-RBC-unit costs between $522 and $1183 (mean, $761 +/- $294). These exceed previously reported estimates and were 3.2- to 4.8-fold higher than blood product acquisition costs. Annual expenditures on blood and transfusion-related activities, limited to surgical patients, ranged from $1.62 to $6.03 million per hospital and were largely related to the transfusion rate. Applicable to various hospital practices, the ABC model confirms that blood costs have been underestimated and that they are geographically variable and identifies opportunities for cost containment. Studies to determine whether more stringent control of blood utilization improves health care utilization and quality, and further reduces costs, are warranted.

Manufacturing methods of a composite cell case for a Ni-Cd battery

NASA Technical Reports Server (NTRS)

Bauer, J. L.; Bogner, R. S.; Lowe, E. P.; Orlowski, E.

1979-01-01

Graphite epoxy material for a nickel cadmium battery cell case has been evaluated and determined to perform in the simulated environment of the battery. The basic manufacturing method requires refinement to demonstrate production feasibility. The various facets of production scale-up, i.e., process and tooling development together with material and process control, have been integrated into a comprehensive manufacturing process that assures production reproducibility and product uniformity. Test results substantiate that a battery cell case produced from graphite epoxy pre-impregnated material utilizing internal pressure bag fabrication method is feasible.

Automated Signal Processing Applied to Volatile-Based Inspection of Greenhouse Crops

PubMed Central

Jansen, Roel; Hofstee, Jan Willem; Bouwmeester, Harro; van Henten, Eldert

2010-01-01

Gas chromatograph–mass spectrometers (GC-MS) have been used and shown utility for volatile-based inspection of greenhouse crops. However, a widely recognized difficulty associated with GC-MS application is the large and complex data generated by this instrument. As a consequence, experienced analysts are often required to process this data in order to determine the concentrations of the volatile organic compounds (VOCs) of interest. Manual processing is time-consuming, labour intensive and may be subject to errors due to fatigue. The objective of this study was to assess whether or not GC-MS data can also be automatically processed in order to determine the concentrations of crop health associated VOCs in a greenhouse. An experimental dataset that consisted of twelve data files was processed both manually and automatically to address this question. Manual processing was based on simple peak integration while the automatic processing relied on the algorithms implemented in the MetAlign™ software package. The results of automatic processing of the experimental dataset resulted in concentrations similar to that after manual processing. These results demonstrate that GC-MS data can be automatically processed in order to accurately determine the concentrations of crop health associated VOCs in a greenhouse. When processing GC-MS data automatically, noise reduction, alignment, baseline correction and normalisation are required. PMID:22163594

Procurement engineering - the productivity factor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bargerstock, S.B.

1993-01-01

The industry is several years on the road to implementation of the Nuclear Management and Resources Council (NUMARC) initiatives on commercial-grade item dedication and procurement. Utilities have taken several approaches to involve engineering in the procurement process. A common result for the approaches is the additional operations and maintenance (O M) cost imposed by the added resource requirements. Procurement engineering productivity is a key element in controlling this business area. Experience shows that 400 to 500% improvements in productivity are possible with a 2-yr period. Improving the productivity of the procurement engineering function is important in today's competitive utility environment.more » Procurement engineering typically involves four distinct technical evaluation responsibilities along with several administrative areas. Technical evaluations include the functionally based safety classification of replacement components and parts (lacking a master parts list), the determination of dedication requirements for safety-related commercial-grade items, the preparation of a procurement specification to maintain the licensed design bases, and the equivalency evaluation of alternate items not requiring the design-change process. Administrative duties include obtaining technical review of vendor-supplied documentation, identifying obsolete parts and components, resolving material nonconformances, initiating the design-change process for replacement items (as needed), and providing technical support to O M. Although most utilities may not perform or require all the noted activities, a large percentage will apply to each utility station.« less

Implementation of a partitioned algorithm for simulation of large CSI problems

NASA Technical Reports Server (NTRS)

Alvin, Kenneth F.; Park, K. C.

1991-01-01

The implementation of a partitioned numerical algorithm for determining the dynamic response of coupled structure/controller/estimator finite-dimensional systems is reviewed. The partitioned approach leads to a set of coupled first and second-order linear differential equations which are numerically integrated with extrapolation and implicit step methods. The present software implementation, ACSIS, utilizes parallel processing techniques at various levels to optimize performance on a shared-memory concurrent/vector processing system. A general procedure for the design of controller and filter gains is also implemented, which utilizes the vibration characteristics of the structure to be solved. Also presented are: example problems; a user's guide to the software; the procedures and algorithm scripts; a stability analysis for the algorithm; and the source code for the parallel implementation.

System and method for high precision isotope ratio destructive analysis

DOEpatents

Bushaw, Bruce A; Anheier, Norman C; Phillips, Jon R

2013-07-02

A system and process are disclosed that provide high accuracy and high precision destructive analysis measurements for isotope ratio determination of relative isotope abundance distributions in liquids, solids, and particulate samples. The invention utilizes a collinear probe beam to interrogate a laser ablated plume. This invention provides enhanced single-shot detection sensitivity approaching the femtogram range, and isotope ratios that can be determined at approximately 1% or better precision and accuracy (relative standard deviation).

Economic analysis of open space box model utilization in spacecraft

NASA Astrophysics Data System (ADS)

Mohammad, Atif F.; Straub, Jeremy

2015-05-01

It is a known fact that the amount of data about space that is stored is getting larger on an everyday basis. However, the utilization of Big Data and related tools to perform ETL (Extract, Transform and Load) applications will soon be pervasive in the space sciences. We have entered in a crucial time where using Big Data can be the difference (for terrestrial applications) between organizations underperforming and outperforming their peers. The same is true for NASA and other space agencies, as well as for individual missions and the highly-competitive process of mission data analysis and publication. In most industries, conventional opponents and new candidates alike will influence data-driven approaches to revolutionize and capture the value of Big Data archives. The Open Space Box Model is poised to take the proverbial "giant leap", as it provides autonomic data processing and communications for spacecraft. We can find economic value generated from such use of data processing in our earthly organizations in every sector, such as healthcare, retail. We also can easily find retailers, performing research on Big Data, by utilizing sensors driven embedded data in products within their stores and warehouses to determine how these products are actually used in the real world.

Using Operational Analysis to Improve Access to Pulmonary Function Testing.

PubMed

Ip, Ada; Asamoah-Barnieh, Raymond; Bischak, Diane P; Davidson, Warren J; Flemons, W Ward; Pendharkar, Sachin R

2016-01-01

Background. Timely pulmonary function testing is crucial to improving diagnosis and treatment of pulmonary diseases. Perceptions of poor access at an academic pulmonary function laboratory prompted analysis of system demand and capacity to identify factors contributing to poor access. Methods. Surveys and interviews identified stakeholder perspectives on operational processes and access challenges. Retrospective data on testing demand and resource capacity was analyzed to understand utilization of testing resources. Results. Qualitative analysis demonstrated that stakeholder groups had discrepant views on access and capacity in the laboratory. Mean daily resource utilization was 0.64 (SD 0.15), with monthly average utilization consistently less than 0.75. Reserved testing slots for subspecialty clinics were poorly utilized, leaving many testing slots unfilled. When subspecialty demand exceeded number of reserved slots, there was sufficient capacity in the pulmonary function schedule to accommodate added demand. Findings were shared with stakeholders and influenced scheduling process improvements. Conclusion. This study highlights the importance of operational data to identify causes of poor access, guide system decision-making, and determine effects of improvement initiatives in a variety of healthcare settings. Importantly, simple operational analysis can help to improve efficiency of health systems with little or no added financial investment.

Detection of LiveLock in BPMN Using Process Expression

NASA Astrophysics Data System (ADS)

Tantitharanukul, Nasi; Jumpamule, Watcharee

Although the Business Process Modeling Notation (BPMN) is a popular tool for modeling business process in conceptual level, the result diagram may contain structural problem. One of the structural problems is livelock. In this problem, one token proceeds to end event, while other token is still in process with no progression. In this paper, we introduce an expression liked method to detect livelock in the BPMN diagram. Our approach utilizes the power of the declarative ability of expression to determine all of the possible process chains, and indicate whether there are livelock or not. As a result, we have shown that our method can detect livelock, if any.

Design of a Fission 99 Mo Recovery Process and Implications toward Mo Adsorption Mechanism on Titania and Alumina Sorbents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stepinski, Dominique C.; Youker, Amanda J.; Krahn, Elizabeth O.

2017-03-01

Molybdenum-99 is a parent of the most widely used medical isotope technetium-99m. Proliferation concerns have prompted development of alternative Mo production methods utilizing low enriched uranium. Alumina and titania sorbents were evaluated for separation of Mo from concentrated uranyl nitrate solutions. System, mass transfer, and isotherm parameters were determined to enable design of Mo separation processes under a wide range of conditions. A model-based approach was utilized to design representative commercial-scale column processes. The designs and parameters were verified with bench-scale experiments. The results are essential for design of Mo separation processes from irradiated uranium solutions, selection of support materialmore » and process optimization. Mo uptake studies show that adsorption decreases with increasing concentration of uranyl nitrate; howeveL, examination of Mo adsorption as a function of nitrate ion concentration shows no dependency, indicating that uranium competes with Mo for adsorption sites. These results are consistent with reports indicating that Mo forms inner-sphere complexes with titania and alumina surface groups.« less

Mass Spectrometric Monitoring of Animal Feed for BSE Spread

ERIC Educational Resources Information Center

King, Angela G.

2004-01-01

The researchers in London have developed an emerging technology that utilizes mass spectrometry to detect processed animal protein (PAP) in animal feed. The amount of animal protein in the feed can be determined by the ratio of the hydrolyzed gelatine signal at m/z 1044 to an internal standard signal at m/z 556.

Use of the Illinois 5Essentials Survey Data. Policy Research: IERC 2014-2

ERIC Educational Resources Information Center

Klostermann, Brenda K.; White, Bradford R.; Lichtenberger, Eric J.; Holt, Janet K.

2014-01-01

The purpose of this study is to examine how Illinois school districts are utilizing the Illinois 5Essentials Survey results, particularly for school improvement, to determine challenges to successful implementation, and to make recommendations for improvements to the 5E Survey and implementation process for statewide use. We also summarize…

Health Information Exchange: The Determinants of Usage and the Impact on Utilization

ERIC Educational Resources Information Center

Vest, Joshua Ryan

2010-01-01

Health information exchange (HIE) is the process of electronically sharing patient-level information among different organizations with the objectives of quality and cost improvements. The adoption of HIE in the United States is not widespread, but numerous efforts at facilitating HIE exist and the incentives for electronic health record system…

Superintendents as Sensemakers in the Design of Sustainable Schools

ERIC Educational Resources Information Center

Klocko, Barbara A.

2009-01-01

The impact of the superintendent in the design decision-making process of sustainable school buildings was examined in this study to determine whether superintendents who have more knowledge and commitment to sustainability have a greater influence on green building practices within their school districts than those who do not. Utilizing a…

Evaluating the Consistency of Scales Used in Adult Attention Deficit Hyperactivity Disorder Assessment of College-Aged Adults

ERIC Educational Resources Information Center

Saleh, Ayman; Fuchs, Catherine; Taylor, Warren D.; Niarhos, Frances

2018-01-01

Objective: Neurocognitive evaluations are commonly integrated with clinical assessment to evaluate adult Attention Deficit Hyperactivity Disorder (ADHD). Study goal is to identify measures most strongly related to ADHD diagnosis and to determine their utility in screening processes. Participants: 230 students who were evaluated at the Vanderbilt…

Research of Technical Knowledge and Creativity Development of Children in Pre-Primary Education through Interactive Whiteboard

ERIC Educational Resources Information Center

Brecka, Peter; Cervenanská, Marcela

2016-01-01

The introduced study represents methodology and results of research focused on utilization of interactive whiteboard as didactic technology mediating information through multimedia worksheets applied in education process in pre-primary education. Its aim was to determine whether it can significantly increase the level of children's acquired…

Mechanisms of Power within a Community-Based Food Security Planning Process

ERIC Educational Resources Information Center

McCullum, Christine; Pelletier, David; Barr, Donald; Wilkins, Jennifer; Habicht, Jean-Pierre

2004-01-01

A community food security movement has begun to address problems of hunger and food insecurity by utilizing a community-based approach. Although various models have been implemented, little empirical research has assessed how power operates within community-based food security initiatives. The purpose of this research was to determine how power…

PILOT-SCALE PARAMETRIC TESTING OF SPRAY DRYER SO2 SCRUBBER FOR LOW-TO-MODERATE SULFUR COAL UTILITY APPLICATIONS

EPA Science Inventory

The report gives results of a comprehensive, pilot, dry, SO2 scrubbing test program to determine the effects of process variables on SO2 removal. In the spray dryer, stoichiometric ratio, flue gas temperature approach to adiabatic saturation, and temperature drop across the spray...

Multi-temporal sub-pixel landsat ETM+ classification of isolated wetlands in Cuyahoga County, Ohio, USA

EPA Science Inventory

The goal of this project was to determine the utility of subpixel processing of multi-temporal Landsat Enhanced Thematic Mapper Plus (ETM+) data for the detection of isolated wetlands greater than 0.50 acres in Cuyahoga County, located in the Erie Drift Plains ecoregion of northe...

Determinants of Student Satisfaction in Online Tutorial: A Study of A Distance Education Institution

ERIC Educational Resources Information Center

Harsasi, Meirani; Sutawijaya, Adrian

2018-01-01

Education system nowadays tends to utilize online learning, including in higher education. Online learning system becomes a major requirement in implementing learning process, including in Indonesia. Universitas Terbuka has implemented online learning system known as online tutorials to support the distance learning system. One interesting issue…

Utility and Usability as Factors Influencing Teacher Decisions about Software Integration

ERIC Educational Resources Information Center

Okumus, Samet; Lewis, Lindsey; Wiebe, Eric; Hollebrands, Karen

2016-01-01

Given the importance of teacher in the implementation of computer technology in classrooms, the technology acceptance model and TPACK model were used to better understand the decision-making process teachers use in determining how, when, and where computer software is used in mathematics classrooms. Thirty-four (34) teachers implementing…

ECUT (Energy Conversion and Utilization Technologies Program). Biocatalysis Project

NASA Technical Reports Server (NTRS)

1986-01-01

Presented are the FY 1985 accomplishments, activities, and planned research efforts of the Biocatalysis Project of the U.S. Department of Energy, Energy Conversion and Utilization Technologies (ECUT) Program. The Project's technical activities were organized as follows: In the Molecular Modeling and Applied Genetics work element, research focused on (1) modeling and simulation studies to establish the physiological basis of high temperature tolerance in a selected enzyme and the catalytic mechanisms of three species of another enzyme, and (2) determining the degree of plasmid amplification and stability of several DNA bacterial strains. In the Bioprocess Engineering work element, research focused on (1) studies of plasmid propagation and the generation of models, (2) developing methods for preparing immobilized biocatalyst beads, and (3) developing an enzyme encapsulation method. In the Process Design and Analysis work element, research focused on (1) further refinement of a test case simulation of the economics and energy efficiency of alternative biocatalyzed production processes, (2) developing a candidate bioprocess to determine the potential for reduced energy consumption and facility/operating costs, and (3) a techno-economic assessment of potential advancements in microbial ammonia production.

Visualizing 3D Food Microstructure Using Tomographic Methods: Advantages and Disadvantages.

PubMed

Wang, Zi; Herremans, Els; Janssen, Siem; Cantre, Dennis; Verboven, Pieter; Nicolaï, Bart

2018-03-25

X-ray micro-computed tomography (micro-CT) provides the unique ability to capture intact internal microstructure data without significant preparation of the sample. The fundamentals of micro-CT technology are briefly described along with a short introduction to basic image processing, quantitative analysis, and derivative computational modeling. The applications and limitations of micro-CT in industries such as meat, dairy, postharvest, and bread/confectionary are discussed to serve as a guideline to the plausibility of utilizing the technique for detecting features of interest. Component volume fractions, their respective size/shape distributions, and connectivity, for example, can be utilized for product development, manufacturing process tuning and/or troubleshooting. In addition to determining structure-function relations, micro-CT can be used for foreign material detection to further ensure product quality and safety. In most usage scenarios, micro-CT in its current form is perfectly adequate for determining microstructure in a wide variety of food products. However, in low-contrast and low-stability samples, emphasis is placed on the shortcomings of the current systems to set realistic expectations for the intended users.

Utility usage forecasting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hosking, Jonathan R. M.; Natarajan, Ramesh

The computer creates a utility demand forecast model for weather parameters by receiving a plurality of utility parameter values, wherein each received utility parameter value corresponds to a weather parameter value. Determining that a range of weather parameter values lacks a sufficient amount of corresponding received utility parameter values. Determining one or more utility parameter values that corresponds to the range of weather parameter values. Creating a model which correlates the received and the determined utility parameter values with the corresponding weather parameters values.

Reassessing the Formation of CK7 Northwest Africa (NWA) 8186

NASA Technical Reports Server (NTRS)

Srinivasan, P.; McCubbin, F. M.; Lapen, T. J.; Righter, M.; Agee, C. B.

2017-01-01

The classification of meteorites is commonly determined using isotopes, modal mineralogy, and bulk compositions [1]. Bulk rare earth elements (REEs) in meteorites are additionally utilized to understand parent body processes. Numerous authors have shown that chondritic groups exhibit REE patterns that may be attributable to their parent bodies [e.g. 2-4], and variations in abundances and concentrations of REEs may reflect early nebular processes, thermal metamorphism, and aqueous alteration on the parent body [5-6].

Anlysis capabilities for plutonium-238 programs

NASA Astrophysics Data System (ADS)

Wong, A. S.; Rinehart, G. H.; Reimus, M. H.; Pansoy-Hjelvik, M. E.; Moniz, P. F.; Brock, J. C.; Ferrara, S. E.; Ramsey, S. S.

2000-07-01

In this presentation, an overview of analysis capabilities that support 238Pu programs will be discussed. These capabilities include neutron emission rate and calorimetric measurements, metallography/ceramography, ultrasonic examination, particle size determination, and chemical analyses. The data obtained from these measurements provide baseline parameters for fuel clad impact testing, fuel processing, product certifications, and waste disposal. Also several in-line analyses capabilities will be utilized for process control in the full-scale 238Pu Aqueous Scrap Recovery line in FY01.

The USGS role in mapping the nation's submerged lands

USGS Publications Warehouse

Schwab, Bill; Haines, John

2004-01-01

The seabed provides habitat for a diverse marine life having commercial, recreational, and intrinsic value. The habitat value of the seabed is largely a function of the geological structure and related geological, biological, oceanologic, and geochemical processes. Of equal importance, the nation's submerged lands contain energy and mineral resources and are utilized for the siting of offshore infrastructure and waste disposal. Seabed character and processes influence the safety and viability of offshore operations. Seabed and subseabed characterization is a prerequisite for the assessment, protection, and utilization of both living and non-living marine resources. A comprehensive program to characterize and understand the nation's submerged lands requires scientific expertise in the fields of geology, biology, hydrography, and oceanography. The U.S. Geological Survey (USGS) has long experience as the Federal agency charged with conducting geologic research and mapping in both coastal and offshore regions. The USGS Coastal and Marine Geology Program (CMGP) leads the nation in expertise related to characterization of seabed and subseabed geology, geological processes, seabed dynamics, and (in collaboration with the National Oceanic and Atmospheric Administration (NOAA) and international partners) habitat geoscience. Numerous USGS studies show that sea-floor geology and processes determine the character and distribution of biological habitats, control coastal evolution, influence the coastal response to storm events and human alterations, and determine the occurrence and concentration of natural resources.

High-throughput process development: determination of dynamic binding capacity using microtiter filter plates filled with chromatography resin.

PubMed

Bergander, Tryggve; Nilsson-Välimaa, Kristina; Oberg, Katarina; Lacki, Karol M

2008-01-01

Steadily increasing demand for more efficient and more affordable biomolecule-based therapies put a significant burden on biopharma companies to reduce the cost of R&D activities associated with introduction of a new drug to the market. Reducing the time required to develop a purification process would be one option to address the high cost issue. The reduction in time can be accomplished if more efficient methods/tools are available for process development work, including high-throughput techniques. This paper addresses the transitions from traditional column-based process development to a modern high-throughput approach utilizing microtiter filter plates filled with a well-defined volume of chromatography resin. The approach is based on implementing the well-known batch uptake principle into microtiter plate geometry. Two variants of the proposed approach, allowing for either qualitative or quantitative estimation of dynamic binding capacity as a function of residence time, are described. Examples of quantitative estimation of dynamic binding capacities of human polyclonal IgG on MabSelect SuRe and of qualitative estimation of dynamic binding capacity of amyloglucosidase on a prototype of Capto DEAE weak ion exchanger are given. The proposed high-throughput method for determination of dynamic binding capacity significantly reduces time and sample consumption as compared to a traditional method utilizing packed chromatography columns without sacrificing the accuracy of data obtained.

Validation of the conceptual research utilization scale: an application of the standards for educational and psychological testing in healthcare

PubMed Central

2011-01-01

Background There is a lack of acceptable, reliable, and valid survey instruments to measure conceptual research utilization (CRU). In this study, we investigated the psychometric properties of a newly developed scale (the CRU Scale). Methods We used the Standards for Educational and Psychological Testing as a validation framework to assess four sources of validity evidence: content, response processes, internal structure, and relations to other variables. A panel of nine international research utilization experts performed a formal content validity assessment. To determine response process validity, we conducted a series of one-on-one scale administration sessions with 10 healthcare aides. Internal structure and relations to other variables validity was examined using CRU Scale response data from a sample of 707 healthcare aides working in 30 urban Canadian nursing homes. Principal components analysis and confirmatory factor analyses were conducted to determine internal structure. Relations to other variables were examined using: (1) bivariate correlations; (2) change in mean values of CRU with increasing levels of other kinds of research utilization; and (3) multivariate linear regression. Results Content validity index scores for the five items ranged from 0.55 to 1.00. The principal components analysis predicted a 5-item 1-factor model. This was inconsistent with the findings from the confirmatory factor analysis, which showed best fit for a 4-item 1-factor model. Bivariate associations between CRU and other kinds of research utilization were statistically significant (p < 0.01) for the latent CRU scale score and all five CRU items. The CRU scale score was also shown to be significant predictor of overall research utilization in multivariate linear regression. Conclusions The CRU scale showed acceptable initial psychometric properties with respect to responses from healthcare aides in nursing homes. Based on our validity, reliability, and acceptability analyses, we recommend using a reduced (four-item) version of the CRU scale to yield sound assessments of CRU by healthcare aides. Refinement to the wording of one item is also needed. Planned future research will include: latent scale scoring, identification of variables that predict and are outcomes to conceptual research use, and longitudinal work to determine CRU Scale sensitivity to change. PMID:21595888

Determining level of care appropriateness in the patient journey from acute care to rehabilitation

PubMed Central

2011-01-01

Background The selection of patients for rehabilitation, and the timing of transfer from acute care, are important clinical decisions that impact on care quality and patient flow. This paper reports utilization review data on inpatients in acute care with stroke, hip fracture or elective joint replacement, and other inpatients referred for rehabilitation. It examines reasons why acute level of care criteria are not met and explores differences in decision making between acute care and rehabilitation teams around patient appropriateness and readiness for transfer. Methods Cohort study of patients in a large acute referral hospital in Australia followed with the InterQual utilization review tool, modified to also include reasons why utilization criteria are not met. Additional data on team decision making about appropriateness for rehabilitation, and readiness for transfer, were collected on a subset of patients. Results There were 696 episodes of care (7189 bed days). Days meeting acute level of care criteria were 56% (stroke, hip fracture and joint replacement patients) and 33% (other patients, from the time of referral). Most inappropriate days in acute care were due to delays in processes/scheduling (45%) or being more appropriate for rehabilitation or lower level of care (30%). On the subset of patients, the acute care team and the utilization review tool deemed patients ready for rehabilitation transfer earlier than the rehabilitation team (means of 1.4, 1.3 and 4.0 days from the date of referral, respectively). From when deemed medically stable for transfer by the acute care team, 28% of patients became unstable. From when deemed stable by the rehabilitation team or utilization review, 9% and 11%, respectively, became unstable. Conclusions A high proportion of patient days did not meet acute level of care criteria, due predominantly to inefficiencies in care processes, or to patients being more appropriate for an alternative level of care, including rehabilitation. The rehabilitation team was the most accurate in determining ongoing medical stability, but at the cost of a longer acute stay. To avoid inpatients remaining in acute care in a state of 'terra nullius', clinical models which provide rehabilitation within acute care, and more efficient movement to a rehabilitation setting, is required. Utilization review could have a decision support role in the determination of medical stability. PMID:22040281

12 CFR 1320.13 - Council determination regarding systemic importance.

Code of Federal Regulations, 2014 CFR

2014-01-01

... FINANCIAL MARKET UTILITIES Consultations, Determinations and Hearings § 1320.13 Council determination regarding systemic importance. (a) Designation determination. The Council shall designate a financial market utility if the Council determines that the financial market utility is, or is likely to become...

12 CFR 1320.13 - Council determination regarding systemic importance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... FINANCIAL MARKET UTILITIES Consultations, Determinations and Hearings § 1320.13 Council determination regarding systemic importance. (a) Designation determination. The Council shall designate a financial market utility if the Council determines that the financial market utility is, or is likely to become...

12 CFR 1320.13 - Council determination regarding systemic importance.

Code of Federal Regulations, 2013 CFR

2013-01-01

... FINANCIAL MARKET UTILITIES Consultations, Determinations and Hearings § 1320.13 Council determination regarding systemic importance. (a) Designation determination. The Council shall designate a financial market utility if the Council determines that the financial market utility is, or is likely to become...

Energy determination in industrial X-ray processing facilities

NASA Astrophysics Data System (ADS)

Cleland, M. R.; Gregoire, O.; Stichelbaut, F.; Gomola, I.; Galloway, R. A.; Schlecht, J.

2005-12-01

In industrial irradiation facilities, the determination of maximum photon or electron energy is important for regulated processes, such as food irradiation, and for assurance of treatment reproducibility. With electron beam irradiators, this has been done by measuring the depth-dose distribution in a homogeneous material. For X-ray irradiators, an analogous method has not yet been recommended. This paper describes a procedure suitable for typical industrial irradiation processes, which is based on common practice in the field of therapeutic X-ray treatment. It utilizes a measurement of the slope of the exponential attenuation curve of X-rays in a thick stack of polyethylene plates. Monte Carlo simulations and experimental tests have been performed to verify the suitability and accuracy of the method between 3 MeV and 8 MeV.

Assessment of laboratory test utilization for HIV/AIDS care in urban ART clinics of Lilongwe, Malawi.

PubMed

Palchaudhuri, Sonali; Tweya, Hannock; Hosseinipour, Mina

2014-06-01

The 2011 Malawi HIV guidelines promote CD4 monitoring for pre-ART assessment and considering HIVRNA monitoring for ART response assessment, while some clinics used CD4 for both. We assessed clinical ordering practices as compared to guidelines, and determined whether the samples were successfully and promptly processed. We conducted a retrospective review of all patients seen in from August 2010 through July 2011,, in two urban HIV-care clinics that utilized 6-monthly CD4 monitoring regardless of ART status. We calculated the percentage of patients on whom clinicians ordered CD4 or HIVRNA analysis. For all samples sent, we determined rates of successful lab-processing, and mean time to returned results. Of 20581 patients seen, 8029 (39%) had at least one blood draw for CD4 count. Among pre-ART patients, 2668/2844 (93.8%) had CD4 counts performed for eligibility. Of all CD4 samples sent, 8082/9207 (89%) samples were successfully processed. Of those, mean time to processing was 1.6 days (s.d 1.5) but mean time to results being available to clinician was 9.3 days (s.d. 3.7). Regarding HIVRNA, 172 patients of 17737 on ART had a blood draw and only 118/213 (55%) samples were successfully processed. Mean processing time was 39.5 days (s.d. 21.7); mean time to results being available to clinician was 43.1 days (s.d. 25.1). During the one-year evaluated, there were multiple lapses in processing HIVRNA samples for up to 2 months. Clinicians underutilize CD4 and HIVRNA as monitoring tools in HIV care. Laboratory processing failures and turnaround times are unacceptably high for viral load analysis. Alternative strategies need to be considered in order to meet laboratory monitoring needs.

Optimization of the dressing parameters in cylindrical grinding based on a generalized utility function

NASA Astrophysics Data System (ADS)

Aleksandrova, Irina

2016-01-01

The existing studies, concerning the dressing process, focus on the major influence of the dressing conditions on the grinding response variables. However, the choice of the dressing conditions is often made, based on the experience of the qualified staff or using data from reference books. The optimal dressing parameters, which are only valid for the particular methods and dressing and grinding conditions, are also used. The paper presents a methodology for optimization of the dressing parameters in cylindrical grinding. The generalized utility function has been chosen as an optimization parameter. It is a complex indicator determining the economic, dynamic and manufacturing characteristics of the grinding process. The developed methodology is implemented for the dressing of aluminium oxide grinding wheels by using experimental diamond roller dressers with different grit sizes made of medium- and high-strength synthetic diamonds type ??32 and ??80. To solve the optimization problem, a model of the generalized utility function is created which reflects the complex impact of dressing parameters. The model is built based on the results from the conducted complex study and modeling of the grinding wheel lifetime, cutting ability, production rate and cutting forces during grinding. They are closely related to the dressing conditions (dressing speed ratio, radial in-feed of the diamond roller dresser and dress-out time), the diamond roller dresser grit size/grinding wheel grit size ratio, the type of synthetic diamonds and the direction of dressing. Some dressing parameters are determined for which the generalized utility function has a maximum and which guarantee an optimum combination of the following: the lifetime and cutting ability of the abrasive wheels, the tangential cutting force magnitude and the production rate of the grinding process. The results obtained prove the possibility of control and optimization of grinding by selecting particular dressing parameters.

Load research manual. Volume 2. Fundamentals of implementing load research procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandenburg, L.; Clarkson, G.; Grund, Jr., C.

This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussedmore » in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.« less

Site Classification using Multichannel Channel Analysis of Surface Wave (MASW) method on Soft and Hard Ground

NASA Astrophysics Data System (ADS)

Ashraf, M. A. M.; Kumar, N. S.; Yusoh, R.; Hazreek, Z. A. M.; Aziman, M.

2018-04-01

Site classification utilizing average shear wave velocity (Vs(30) up to 30 meters depth is a typical parameter. Numerous geophysical methods have been proposed for estimation of shear wave velocity by utilizing assortment of testing configuration, processing method, and inversion algorithm. Multichannel Analysis of Surface Wave (MASW) method is been rehearsed by numerous specialist and professional to geotechnical engineering for local site characterization and classification. This study aims to determine the site classification on soft and hard ground using MASW method. The subsurface classification was made utilizing National Earthquake Hazards Reduction Program (NERHP) and international Building Code (IBC) classification. Two sites are chosen to acquire the shear wave velocity which is in the state of Pulau Pinang for soft soil and Perlis for hard rock. Results recommend that MASW technique can be utilized to spatially calculate the distribution of shear wave velocity (Vs(30)) in soil and rock to characterize areas.

Evolution of the Human Immunodeficiency Virus Type 1 Envelope during Infection Reveals Molecular Corollaries of Specificity for Coreceptor Utilization and AIDS Pathogenesis

PubMed Central

Hu, Qin-xue; Barry, Ashley Perkins; Wang, Zi-xuan; Connolly, Shanon M.; Peiper, Stephen C.; Greenberg, Michael L.

2000-01-01

The evolution of human immunodeficiency virus type 1 infection is associated with a shift in the target cell population, driven by variability in coreceptor utilization resulting from diversity in env. To elucidate the potential consequences of these changes for Env-mediated fusion over the course of AIDS, we examined the biological properties of serial viral isolates and determined coreceptor utilization by the products of env cloned from two individuals, followed from the detection of seroconversion throughout the course of their infection. One had a typical course, and the other had an accelerated progression. Early isolates were non-syncytium inducing, and the corresponding Env exclusively utilized CCR5, whereas Env from late phases of infection showed restricted utilization of CXCR4 in both patients. Env from subject SC24, who had a standard progression, demonstrated multitropism, manifested by utilization of CCR3, CXCR4, and CCR5 in the intervening period. In contrast, Env from patient SC51, who experienced early conversion to the syncytium-inducing phenotype, developed dualtropic coreceptor utilization of CCR5 and CXCR4. Genetic analysis of env from each isolate revealed that those with an X4 phenotype formed a distinct subcluster within each subject. Analysis of chimeras constructed from R5 and multispecific env from patient SC24 demonstrated that while the V3 domain played a dominant role in determining coreceptor utilization, sequences in the V4–V5 region also contributed to the latter phenotype. Immunoprecipitation experiments confirmed that the hybrid Env proteins were expressed at similar levels. These experiments demonstrate that progression from the R5 to X4 phenotype may occur through a multi- or dual-tropic intermediate and that multiple domains contribute to this process. PMID:11090186

Utilization of lignite power generation residues for the production of lightweight aggregates.

PubMed

Anagnostopoulos, Iason M; Stivanakis, Victor E

2009-04-15

A novel process is proposed for the utilization of lignite combustion solid residues in the production of inflammable lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering, and carbon contained in BA was used as the process fuel. The main residues bottom ash (BA) and fly ash (FA) from Megalopolis power plant were characterized, mixed in different proportions and treated through pelletization and sintering process. Sintering benefits from combustion of BA carbon content and the product is a hardened porous cake. The energy required for achievement of high temperatures, in the range of 1250 degrees C, was offered by carbon combustion and CO(2) evolution is responsible for porous structure formation. Selected physical properties of sintered material relevant to use as lightweight aggregates were determined, including bulk density, porosity and water absorption. Bulk density varies from 0.83 to 0.91 g/cm(3), porosity varies from 60% to 64% and water absorption varies from 66% to 80%. LWA formed is used for the production of lightweight aggregate concrete (LWAC). Thermal conductivity coefficient varies from 0.25 to 0.37 W/mK (lower than maximum limit 0.43 W/mK) and compressive strength varies from 19 to 23 MPa (higher than minimum limit 17 MPa). The results indicate that sintering of lignite combustion residues is an efficient method of utilization of carbon containing BA and production of LWA for structural and insulating purposes. Carbon content of BA is a key factor in LWA production. Finally, this research work comprises the first proposed application for utilization of BA in Greece.

Argon-oxygen atmospheric pressure plasma treatment on carbon fiber reinforced polymer for improved bonding

NASA Astrophysics Data System (ADS)

Chartosias, Marios

Acceptance of Carbon Fiber Reinforced Polymer (CFRP) structures requires a robust surface preparation method with improved process controls capable of ensuring high bond quality. Surface preparation in a production clean room environment prior to applying adhesive for bonding would minimize risk of contamination and reduce cost. Plasma treatment is a robust surface preparation process capable of being applied in a production clean room environment with process parameters that are easily controlled and documented. Repeatable and consistent processing is enabled through the development of a process parameter window utilizing techniques such as Design of Experiments (DOE) tailored to specific adhesive and substrate bonding applications. Insight from respective plasma treatment Original Equipment Manufacturers (OEMs) and screening tests determined critical process factors from non-factors and set the associated factor levels prior to execution of the DOE. Results from mode I Double Cantilever Beam (DCB) testing per ASTM D 5528 [1] standard and DOE statistical analysis software are used to produce a regression model and determine appropriate optimum settings for each factor.

Impact of Aircraft Emissions on Air Quality in the Vicinity of Airports. Volume 4. Nitrogen Dioxide and Hydrocarbons.

DTIC Science & Technology

1984-04-01

PROCESSING 2.1.1 Siting, Instrumentation, and Measurement History The ANLIEES Air Resources Section Air Monitoring Laboratory (AM4L) was located at... supplied from an external cylinder in a blend containing 10% C2H4 reactant and 90% CO2 diluent. The instrument was operated in a fast-response mode...an alternative procedure was adopted for their determination and was utilized to determine time lags for several different periods of time scattered

Visual Navigation Constructing and Utilizing Simple Maps of an Indoor Environment

DTIC Science & Technology

1989-03-01

places are con- nected to eachother , so that the robot may plan routes. On a more advanced level. navigation nmay require an understanding of the meaning...two vertical lines, suitably separated from eachother . through which it tries to lead the robot. CHAPTER 1. L’TRODUCTION 14 1.4 Context of the Project...the observer will have no trouble in determining where the wall is. A robot, with far less processing power than humans have. might be able determine

Determination of Absolute Configuration of Secondary Alcohols Using Thin-Layer Chromatography

PubMed Central

Wagner, Alexander J.; Rychnovsky, Scott D.

2013-01-01

A new implementation of the Competing Enantioselective Conversion (CEC) method was developed to qualitatively determine the absolute configuration of enantioenriched secondary alcohols using thin-layer chromatography. The entire process for the method requires approximately 60 min and utilizes micromole quantities of the secondary alcohol being tested. A number of synthetically relevant secondary alcohols are presented. Additionally, 1H NMR spectroscopy was conducted on all samples to provide evidence of reaction conversion that supports the qualitative method presented herein. PMID:23593963

A performability solution method for degradable nonrepairable systems

NASA Technical Reports Server (NTRS)

Furchtgott, D. G.; Meyer, J. F.

1984-01-01

The present performability model-solving algorithm identifies performance with 'reward', representing the state behavior of a system S by a finite-state stochastic process and determining reward by means of reward rates that are associated with the states of the base model. A general method is obtained for determining the probability distribution function of the performance (reward) variable, and therefore the performability, of the corresponding system. This is done for bounded utilization periods, and the result is an integral expression which is either analytically or numerically solvable.

Introduction of water footprint assessment approach to enhance water supply management in Malaysia

NASA Astrophysics Data System (ADS)

Moni, Syazwan N.; Aziz, Edriyana A.; Malek, M. A.

2017-10-01

Presently, Water Footprint (WF) Approach has been used to assess the sustainability of a product's chain globally but is lacking in the services sector. Thus, this paper aims to introduce WF assessment as a technical approach to determine the sustainability of water supply management for the typical water supply treatment process (WSTP) used in Malaysia. Water supply is one of the pertinent services and most of WF accounting begins with data obtained from the water supply treatment plant. Therefore, the amount of WF will be accounted for each process of WSTP in order to determine the water utilization for the whole process according to blue, green and grey WF. Hence, the exact amount of water used in the process can be measured by applying this accounting method to assess the sustainability of water supply management in Malaysia. Therefore, the WF approach in assessing sustainability of WSTP could be implemented.

Distorted Immunodominance by Linker Sequences or other Epitopes from a Second Protein Antigen During Antigen-Processing

PubMed Central

Kim, AeRyon; Boronina, Tatiana N.; Cole, Robert N.; Darrah, Erika; Sadegh-Nasseri, Scheherazade

2017-01-01

The immune system focuses on and responds to very few representative immunodominant epitopes from pathogenic insults. However, due to the complexity of the antigen processing, understanding the parameters that lead to immunodominance has proved difficult. In an attempt to uncover the determinants of immunodominance among several dominant epitopes, we utilized a cell free antigen processing system and allowed the system to identify the hierarchies among potential determinants. We then tested the results in vivo; in mice and in human. We report here, that immunodominance of known sequences in a given protein can change if two or more proteins are being processed and presented simultaneously. Surprisingly, we find that new spacer/tag sequences commonly added to proteins for purification purposes can distort the capture of the physiological immunodominant epitopes. We warn against adding tags and spacers to candidate vaccines, or recommend cleaving it off before using for vaccination. PMID:28422163

Characterization of real-time computers

NASA Technical Reports Server (NTRS)

Shin, K. G.; Krishna, C. M.

1984-01-01

A real-time system consists of a computer controller and controlled processes. Despite the synergistic relationship between these two components, they have been traditionally designed and analyzed independently of and separately from each other; namely, computer controllers by computer scientists/engineers and controlled processes by control scientists. As a remedy for this problem, in this report real-time computers are characterized by performance measures based on computer controller response time that are: (1) congruent to the real-time applications, (2) able to offer an objective comparison of rival computer systems, and (3) experimentally measurable/determinable. These measures, unlike others, provide the real-time computer controller with a natural link to controlled processes. In order to demonstrate their utility and power, these measures are first determined for example controlled processes on the basis of control performance functionals. They are then used for two important real-time multiprocessor design applications - the number-power tradeoff and fault-masking and synchronization.

Role of thermal processes in dewetting of epitaxial Ag(111) film on Si(111)

DOE PAGES

Sanders, Charlotte E.; Zhang, Chendong D.; Kellogg, Gary L.; ...

2014-08-01

Epitaxially grown silver (Ag) film on silicon (Si) is an optimal plasmonic device platform, but its technological utility has been limited by its tendency to dewet rapidly under ambient conditions (standard temperature and pressure). The mechanisms driving this dewetting have not heretofore been determined. In our study, scanning probe microscopy and low-energy electron microscopy are used to compare the morphological evolution of epitaxial Ag(111)/Si(111) under ambient conditions with that of similarly prepared films heated under ultra-high vacuum (UHV) conditions. Furthermore, dewetting is seen to be initiated with the formation of pinholes, which might function to relieve strain in the film.more » We find that in the UHV environment, dewetting is determined by thermal processes, and while under ambient conditions, thermal processes are not required. Finally, we conclude that dewetting in ambient conditions is triggered by some chemical process, most likely oxidation.« less

Complexity study on the Cournot-Bertrand mixed duopoly game model with market share preference

NASA Astrophysics Data System (ADS)

Ma, Junhai; Sun, Lijian; Hou, Shunqi; Zhan, Xueli

2018-02-01

In this paper, a Cournot-Bertrand duopoly model with market share preference is established. Assume that there is a degree of product difference between the two firms, where one firm takes the price as a decision variable and the other takes the quantity. Both firms are bounded rational, with linear cost functions and demand functions. The stability of the equilibrium points is analyzed, and the effects of some parameters (α, β, d and v1) on the model stability are studied. Basins of attraction are investigated and the evolution process is shown with the increase in the output adjustment speed. The simulation results show that instability will lead to the increase in the average utility of the firm that determines the quantity and reduce the average utility of the firm that determines price.

Stellar Gyroscope for Determining Attitude of a Spacecraft

NASA Technical Reports Server (NTRS)

Pain, Bedabrata; Hancock, Bruce; Liebe, Carl; Mellstrom, Jeffrey

2005-01-01

A paper introduces the concept of a stellar gyroscope, currently at an early stage of development, for determining the attitude or spin axis, and spin rate of a spacecraft. Like star trackers, which are commercially available, a stellar gyroscope would capture and process images of stars to determine the orientation of a spacecraft in celestial coordinates. Star trackers utilize chargecoupled devices as image detectors and are capable of tracking attitudes at spin rates of no more than a few degrees per second and update rates typically <5 Hz. In contrast, a stellar gyroscope would utilize an activepixel sensor as an image detector and would be capable of tracking attitude at a slew rate as high as 50 deg/s, with an update rate as high as 200 Hz. Moreover, a stellar gyroscope would be capable of measuring a slew rate up to 420 deg/s. Whereas a Sun sensor and a three-axis mechanical gyroscope are typically needed to complement a star tracker, a stellar gyroscope would function without them; consequently, the mass, power consumption, and mechanical complexity of an attitude-determination system could be reduced considerably.

The establishment of a production-ready manufacturing process utilizing thin silicon substrates for solar cells

NASA Technical Reports Server (NTRS)

Pryor, R. A.

1980-01-01

Three inch diameter Czochralski silicon substrates sliced directly to 5 mil, 8 mil, and 27 mil thicknesses with wire saw techniques were procured. Processing sequences incorporating either diffusion or ion implantation technologies were employed to produce n+p or n+pp+ solar cell structures. These cells were evaluated for performance, ease of fabrication, and cost effectiveness. It was determined that the use of 7 mil or even 4 mil wafers would provide near term cost reductions for solar cell manufacturers.

Method and apparatus for measuring flow velocity using matched filters

DOEpatents

Raptis, Apostolos C.

1983-01-01

An apparatus and method for measuring the flow velocities of individual phase flow components of a multiphase flow utilizes matched filters. Signals arising from flow noise disturbance are extracted from the flow, at upstream and downstream locations. The signals are processed through pairs of matched filters which are matched to the flow disturbance frequency characteristics of the phase flow component to be measured. The processed signals are then cross-correlated to determine the transit delay time of the phase flow component between sensing positions.

Algorithms for Processing and Analysis of Ocean Color Satellite Data for Coastal Case 2 Waters. Chapter 16

NASA Technical Reports Server (NTRS)

Stumpf, Richard P.; Arnone, Robert A.; Gould, Richard W., Jr.; Ransibrahmanakul, Varis; Tester, Patricia A.

2003-01-01

SeaWiFS has the ability to enhance our understanding of many oceanographic processes. However, its utility in the coastal zone has been limited by valid bio-optical algorithms and by the determination of accurate water reflectances, particularly in the blue bands (412-490 nm), which have a significant impact on the effectiveness of all bio-optical algorithms. We have made advances in three areas: algorithm development (Table 16.1), field data collection, and data applications.

Formulation Optimization of Hot Melt Extruded Abuse Deterrent Pellet Dosage Form Utilizing Design of Experiments (DOE)

PubMed Central

Maddineni, Sindhuri; Battu, Sunil Kumar; Morott, Joe; Majumdar, Soumyajit; Repka, Michael A.

2014-01-01

The objective of the present study was to develop techniques for an abuse-deterrent (AD) platform utilizing hot melt extrusion (HME) process. Formulation optimization was accomplished by utilizing Box-Behnken design of experiments to determine the effect of the three formulation factors: PolyOx™ WSR301, Benecel™ K15M, and Carbopol 71G; each of which was studied at three levels on TR attributes of the produced melt extruded pellets. A response surface methodology was utilized to identify the optimized formulation. Lidocaine Hydrochloride was used as a model drug, and suitable formulation ingredients were employed as carrier matrices and processing aids. All of the formulations were evaluated for the TR attributes such as particle size post-milling, gelling, percentage of drug extraction in water and alcohol. All of the DOE formulations demonstrated sufficient hardness and elasticity, and could not be reduced into fine particles (<150µm), which is a desirable feature to prevent snorting. In addition, all of the formulations exhibited good gelling tendency in water with minimal extraction of drug in the aqueous medium. Moreover, Benecel™ K15M in combination with PolyOx™ WSR301 could be utilized to produce pellets with TR potential. HME has been demonstrated to be a viable technique with a potential to develop novel abuse-deterrent formulations. PMID:24433429

Application of online measures to monitor and evaluate multiplatform fusion performance

NASA Astrophysics Data System (ADS)

Stubberud, Stephen C.; Kowalski, Charlene; Klamer, Dale M.

1999-07-01

A primary concern of multiplatform data fusion is assessing the quality and utility of data shared among platforms. Constraints such as platform and sensor capability and task load necessitate development of an on-line system that computes a metric to determine which other platform can provide the best data for processing. To determine data quality, we are implementing an approach based on entropy coupled with intelligent agents. To determine data quality, we are implementing an approach based on entropy coupled with intelligent agents. Entropy measures quality of processed information such as localization, classification, and ambiguity in measurement-to-track association. Lower entropy scores imply less uncertainty about a particular target. When new information is provided, we compuete the level of improvement a particular track obtains from one measurement to another. The measure permits us to evaluate the utility of the new information. We couple entropy with intelligent agents that provide two main data gathering functions: estimation of another platform's performance and evaluation of the new measurement data's quality. Both functions result from the entropy metric. The intelligent agent on a platform makes an estimate of another platform's measurement and provides it to its own fusion system, which can then incorporate it, for a particular target. A resulting entropy measure is then calculated and returned to its own agent. From this metric, the agent determines a perceived value of the offboard platform's measurement. If the value is satisfactory, the agent requests the measurement from the other platform, usually by interacting with the other platform's agent. Once the actual measurement is received, again entropy is computed and the agent assesses its estimation process and refines it accordingly.

The utilization of the seven principles for good practices of full-time and adjunct faculty in teaching health & science in community colleges

NASA Astrophysics Data System (ADS)

Musaitif, Linda M.

Purpose. The purpose of this study was to determine the degree to which undergraduate full-time and adjunct faculty members in the health and science programs at community colleges in Southern California utilize the seven principles of good practice as measured by the Faculty Inventory of the Seven Principles for Good Practice in Undergraduate Education. A second purpose was to compare degree of utilization for gender and class size. Methodology. This is a quantitative study wherein there exists a systematic and mathematical assessment of data gathered through the use of a Likert scale survey to process and determine the mathematical model of the use of the principles by the target population of both full-time and adjunct faculty of health/science programs of community colleges in Southern California. Findings. Examination of the data revealed that both full-time and adjunct faculty members of Southern California community colleges perceive themselves a high degree of utilization of the seven principles of good practice. There was no statistically significant data to suggest a discrepancy between full-time and adjunct professors' perceptions among the utilization of the seven principles. Overall, male faculty members perceived themselves as utilizing the principles to a greater degree than female faculty. Data suggest that faculty with class size 60 or larger showed to utilize the seven principles more frequently than the professors with smaller class sizes. Conclusions. Full-time and adjunct professors of the health and sciences in Southern California community colleges perceive themselves as utilizing the seven principles of good practice to a high degree. Recommendations. This study suggests many recommendations for future research, including the degree to which negative economic factors such as budget cuts and demands affect the utilization of the seven principles. Also recommended is a study comparing students' perceptions of faculty's utilization of the seven principles of good practice in the classroom with faculty's self-perception.

An integrative process model of leadership: examining loci, mechanisms, and event cycles.

PubMed

Eberly, Marion B; Johnson, Michael D; Hernandez, Morela; Avolio, Bruce J

2013-09-01

Utilizing the locus (source) and mechanism (transmission) of leadership framework (Hernandez, Eberly, Avolio, & Johnson, 2011), we propose and examine the application of an integrative process model of leadership to help determine the psychological interactive processes that constitute leadership. In particular, we identify the various dynamics involved in generating leadership processes by modeling how the loci and mechanisms interact through a series of leadership event cycles. We discuss the major implications of this model for advancing an integrative understanding of what constitutes leadership and its current and future impact on the field of psychological theory, research, and practice. © 2013 APA, all rights reserved.

Impact of remote sensing upon the planning, management and development of water resources. Summary of computers and computer growth trends for hydrologic modeling and the input of ERTS image data processing load

NASA Technical Reports Server (NTRS)

Castruccio, P. A.; Loats, H. L., Jr.

1975-01-01

An analysis of current computer usage by major water resources users was made to determine the trends of usage and costs for the principal hydrologic users/models. The laws and empirical relationships governing the growth of the data processing loads were described and applied to project the future data loads. Data loads for ERTS CCT image processing were computed and projected through the 1985 era. The analysis showns significant impact due to the utilization and processing of ERTS CCT's data.

Coal Research

NASA Technical Reports Server (NTRS)

1986-01-01

Coal slurries are "clean" pulverized coal mixed with oil or water. Significant fuel savings can be realized when using coal slurries. Advanced Fuels Technology (AFT) utilized a COSMIC program, (Calculation of Complex Chemical Equilibrium Compositions), which provides specific capabilities for determining combustion products. The company has developed a cleaning process that removes much of the mineral sulphur and ash from the coals.

Incidental Learning in 3D Virtual Environments: Relationships to Learning Style, Digital Literacy and Information Display

ERIC Educational Resources Information Center

Thomas, Wayne W.; Boechler, Patricia M.

2014-01-01

With teachers taking more interest in utilizing 3D virtual environments for educational purposes, research is needed to understand how learners perceive and process information within virtual environments (Eschenbrenner, Nah, & Siau, 2008). In this study, the authors sought to determine if learning style or digital literacy predict incidental…

State Share of Instruction Funding to Ohio Public Community Colleges: A Policy Analysis

ERIC Educational Resources Information Center

Johnson, Betsy

2012-01-01

This study investigated various state policies to determine their impact on the state share of instruction (SSI) funding to community colleges in the state of Ohio. To complete the policy analysis, the researcher utilized three policy analysis tools, defined by Gill and Saunders (2010) as iterative processes, intuition and judgment, and advice and…

Adopting Cut Scores: Post-Standard-Setting Panel Considerations for Decision Makers

ERIC Educational Resources Information Center

Geisinger, Kurt F.; McCormick, Carina M.

2010-01-01

Standard-setting studies utilizing procedures such as the Bookmark or Angoff methods are just one component of the complete standard-setting process. Decision makers ultimately must determine what they believe to be the most appropriate standard or cut score to use, employing the input of the standard-setting panelists as one piece of information…

Using Regression Analysis To Determine If Faculty Salaries Are Overly Compressed. AIR 1997 Annual Forum Paper.

ERIC Educational Resources Information Center

Toutkoushian, Robert K.

This paper proposes a five-step process by which to analyze whether the salary ratio between junior and senior college faculty exhibits salary compression, a term used to describe an unusually small differential between faculty with different levels of experience. The procedure utilizes commonly used statistical techniques (multiple regression…

Heterodyne laser instantaneous frequency measurement system

DOEpatents

Wyeth, Richard W.; Johnson, Michael A.; Globig, Michael A.

1989-01-01

A heterodyne laser instantaneous frequency measurement system is disclosed. The system utilizes heterodyning of a pulsed laser beam with a continuous wave laser beam to form a beat signal. The beat signal is processed by a controller or computer which determines both the average frequency of the laser pulse and any changes or chirp of th frequency during the pulse.

Examining the Impact of Technology on Primary Students' Revision of Written Work

ERIC Educational Resources Information Center

Lisy, Jennifer Garrette

2015-01-01

Few studies have examined the revision processes of second grade students and even fewer have explored the impact of digital writing on young students' revisions. This study utilized a within subject crossover trial using randomized block assignment (AB | BA) for counterbalancing. This study sought to determine (1) whether revising on paper versus…

Lidar and airborne investigation of smoke plume characteristics: Kootenai Creek Fire case study

Treesearch

S. Urbanski; V. Kovalev; W. M. Hao; C. Wold; A. Petkov

2010-01-01

A ground-based scanning lidar was utilized with a set of airborne instruments to acquire measurements of smoke plume dynamics, smoke aerosol distribution and chemical composition in the vicinity of active wildfires in the western U.S. A new retrieval technique was used for processing lidar multiangle measurements. The technique determines the location of...

Goal selection versus process control in a brain-computer interface based on sensorimotor rhythms.

PubMed

Royer, Audrey S; He, Bin

2009-02-01

In a brain-computer interface (BCI) utilizing a process control strategy, the signal from the cortex is used to control the fine motor details normally handled by other parts of the brain. In a BCI utilizing a goal selection strategy, the signal from the cortex is used to determine the overall end goal of the user, and the BCI controls the fine motor details. A BCI based on goal selection may be an easier and more natural system than one based on process control. Although goal selection in theory may surpass process control, the two have never been directly compared, as we are reporting here. Eight young healthy human subjects participated in the present study, three trained and five naïve in BCI usage. Scalp-recorded electroencephalograms (EEG) were used to control a computer cursor during five different paradigms. The paradigms were similar in their underlying signal processing and used the same control signal. However, three were based on goal selection, and two on process control. For both the trained and naïve populations, goal selection had more hits per run, was faster, more accurate (for seven out of eight subjects) and had a higher information transfer rate than process control. Goal selection outperformed process control in every measure studied in the present investigation.

ECG R-R peak detection on mobile phones.

PubMed

Sufi, F; Fang, Q; Cosic, I

2007-01-01

Mobile phones have become an integral part of modern life. Due to the ever increasing processing power, mobile phones are rapidly expanding its arena from a sole device of telecommunication to organizer, calculator, gaming device, web browser, music player, audio/video recording device, navigator etc. The processing power of modern mobile phones has been utilized by many innovative purposes. In this paper, we are proposing the utilization of mobile phones for monitoring and analysis of biosignal. The computation performed inside the mobile phone's processor will now be exploited for healthcare delivery. We performed literature review on RR interval detection from ECG and selected few PC based algorithms. Then, three of those existing RR interval detection algorithms were programmed on Java platform. Performance monitoring and comparison studies were carried out on three different mobile devices to determine their application on a realtime telemonitoring scenario.

Flat plate vs. concentrator solar photovoltaic cells - A manufacturing cost analysis

NASA Technical Reports Server (NTRS)

Granon, L. A.; Coleman, M. G.

1980-01-01

The choice of which photovoltaic system (flat plate or concentrator) to use for utilizing solar cells to generate electricity depends mainly on the cost. A detailed, comparative manufacturing cost analysis of the two types of systems is presented. Several common assumptions, i.e., cell thickness, interest rate, power rate, factory production life, polysilicon cost, and direct labor rate are utilized in this analysis. Process sequences, cost variables, and sensitivity analyses have been studied, and results of the latter show that the most important parameters which determine manufacturing costs are concentration ratio, manufacturing volume, and cell efficiency. The total cost per watt of the flat plate solar cell is $1.45, and that of the concentrator solar cell is $1.85, the higher cost being due to the increased process complexity and material costs.

Examining the architecture of cellular computing through a comparative study with a computer

PubMed Central

Wang, Degeng; Gribskov, Michael

2005-01-01

The computer and the cell both use information embedded in simple coding, the binary software code and the quadruple genomic code, respectively, to support system operations. A comparative examination of their system architecture as well as their information storage and utilization schemes is performed. On top of the code, both systems display a modular, multi-layered architecture, which, in the case of a computer, arises from human engineering efforts through a combination of hardware implementation and software abstraction. Using the computer as a reference system, a simplistic mapping of the architectural components between the two is easily detected. This comparison also reveals that a cell abolishes the software–hardware barrier through genomic encoding for the constituents of the biochemical network, a cell's ‘hardware’ equivalent to the computer central processing unit (CPU). The information loading (gene expression) process acts as a major determinant of the encoded constituent's abundance, which, in turn, often determines the ‘bandwidth’ of a biochemical pathway. Cellular processes are implemented in biochemical pathways in parallel manners. In a computer, on the other hand, the software provides only instructions and data for the CPU. A process represents just sequentially ordered actions by the CPU and only virtual parallelism can be implemented through CPU time-sharing. Whereas process management in a computer may simply mean job scheduling, coordinating pathway bandwidth through the gene expression machinery represents a major process management scheme in a cell. In summary, a cell can be viewed as a super-parallel computer, which computes through controlled hardware composition. While we have, at best, a very fragmented understanding of cellular operation, we have a thorough understanding of the computer throughout the engineering process. The potential utilization of this knowledge to the benefit of systems biology is discussed. PMID:16849179

Examining the architecture of cellular computing through a comparative study with a computer.

PubMed

Wang, Degeng; Gribskov, Michael

2005-06-22

The computer and the cell both use information embedded in simple coding, the binary software code and the quadruple genomic code, respectively, to support system operations. A comparative examination of their system architecture as well as their information storage and utilization schemes is performed. On top of the code, both systems display a modular, multi-layered architecture, which, in the case of a computer, arises from human engineering efforts through a combination of hardware implementation and software abstraction. Using the computer as a reference system, a simplistic mapping of the architectural components between the two is easily detected. This comparison also reveals that a cell abolishes the software-hardware barrier through genomic encoding for the constituents of the biochemical network, a cell's "hardware" equivalent to the computer central processing unit (CPU). The information loading (gene expression) process acts as a major determinant of the encoded constituent's abundance, which, in turn, often determines the "bandwidth" of a biochemical pathway. Cellular processes are implemented in biochemical pathways in parallel manners. In a computer, on the other hand, the software provides only instructions and data for the CPU. A process represents just sequentially ordered actions by the CPU and only virtual parallelism can be implemented through CPU time-sharing. Whereas process management in a computer may simply mean job scheduling, coordinating pathway bandwidth through the gene expression machinery represents a major process management scheme in a cell. In summary, a cell can be viewed as a super-parallel computer, which computes through controlled hardware composition. While we have, at best, a very fragmented understanding of cellular operation, we have a thorough understanding of the computer throughout the engineering process. The potential utilization of this knowledge to the benefit of systems biology is discussed.

Improving overlay control through proper use of multilevel query APC

NASA Astrophysics Data System (ADS)

Conway, Timothy H.; Carlson, Alan; Crow, David A.

2003-06-01

Many state-of-the-art fabs are operating with increasingly diversified product mixes. For example, at Cypress Semiconductor, it is not unusual to be concurrently running multiple technologies and many devices within each technology. This diverse product mix significantly increases the difficulty of manually controlling overlay process corrections. As a result, automated run-to-run feedforward-feedback control has become a necessary and vital component of manufacturing. However, traditional run-to-run controllers rely on highly correlated historical events to forecast process corrections. For example, the historical process events typically are constrained to match the current event for exposure tool, device, process level and reticle ID. This narrowly defined process stream can result in insufficient data when applied to lowvolume or new-release devices. The run-to-run controller implemented at Cypress utilizes a multi-level query (Level-N) correlation algorithm, where each subsequent level widens the search criteria for available historical data. The paper discusses how best to widen the search criteria and how to determine and apply a known bias to account for tool-to-tool and device-to-device differences. Specific applications include offloading lots from one tool to another when the first tool is down for preventive maintenance, utilizing related devices to determine a default feedback vector for new-release devices, and applying bias values to account for known reticle-to-reticle differences. In this study, we will show how historical data can be leveraged from related devices or tools to overcome the limitations of narrow process streams. In particular, this paper discusses how effectively handling narrow process streams allows Cypress to offload lots from a baseline tool to an alternate tool.

Identification of metrics to monitor salt marsh integrity on National Wildlife Refuges in relation to conservation and management objectives

USGS Publications Warehouse

Neckles, Hilary A.; Guntenspergen, Glenn R.; Shriver, W. George; Danz, Nicholas P.; Wiest, Whitney A.; Nagel, Jessica L.; Olker, Jennifer H.

2013-01-01

Implementation of these metrics for quantitative assessment of NWRS salt marsh integrity in FWS Region 5 requires developing sampling designs for each refuge. Additionally, it is important to determine how the monitoring information will be used within a management context. SDM should be used to complete the analysis of salt marsh management decisions. The next steps would involve 1) prioritizing and weighting the management objectives; 2) predicting responses to individual management actions in terms of objectives and metrics; 3) using multiattribute utility theory to convert all measurable attributes to a common utility scale; 4) determining the total management benefit of each action by summing utilities across objectives; and 5) maximizing the total management benefits within cost constraints for each refuge. This process would allow the optimum management decisions for NWRS salt marshes to be selected and implemented based directly on monitoring data and current understanding of marsh responses to management actions. Monitoring the outcome of management actions would then allow new monitoring data to be incorporated into subsequent decisions. 

Determination of the utility of remote sensing data for land use/cover analysis in the lower Appalachia region: Assessing the utility of remote sensing data for archeological site recognition

NASA Technical Reports Server (NTRS)

Weber, N. V.

1983-01-01

Thematic Mapper Simulator (TMS) data were gathered by NASA/ERL over a portion of the lower Ohio River and the middle Mississippi River valleys on April 11, 1982. CIR imagery accompanied the 10 and 30 meter resolution TMS data sets. This area is somewhat unique archeologically as there exists a concentration of sites with major features such as mounds, earthworks, and villages. It was the primary purpose of this study to determine the utility of TMS data in identifying signatures which are distinctly archeological. TMS data were processed using the NASA/ERL software package ELAS. No signatures that were distinctly archeological were detected, due in large part to the complexity of the land cover and land use practices. However, as more sophisticated classification techniques were employed, the classes which were related to archeological features were narrowed. TMS data could certainly be of assistance to a trained archeologist/interpreter in narrowing an area which has to be field-surveyed as anomalous features can be recognized within a particular environmental context.

Characterization of Non-Infectious Virus-Like Particle Surrogates for Viral Clearance Applications.

PubMed

Johnson, Sarah; Brorson, Kurt A; Frey, Douglas D; Dhar, Arun K; Cetlin, David A

2017-09-01

Viral clearance is a critical aspect of biopharmaceutical manufacturing process validation. To determine the viral clearance efficacy of downstream chromatography and filtration steps, live viral "spiking" studies are conducted with model mammalian viruses such as minute virus of mice (MVM). However, due to biosafety considerations, spiking studies are costly and typically conducted in specialized facilities. In this work, we introduce the concept of utilizing a non-infectious MVM virus-like particle (MVM-VLP) as an economical surrogate for live MVM during process development and characterization. Through transmission electron microscopy, size exclusion chromatography with multi-angle light scattering, chromatofocusing, and a novel solute surface hydrophobicity assay, we examined and compared the size, surface charge, and hydrophobic properties of MVM and MVM-VLP. The results revealed that MVM and MVM-VLP exhibited nearly identical physicochemical properties, indicating the potential utility of MVM-VLP as an accurate and economical surrogate to live MVM during chromatography and filtration process development and characterization studies.

The economical utilization of geothermal energy

NASA Astrophysics Data System (ADS)

Rose, G.

1982-12-01

The geothermal energy which is stored in hot dry rock could be theoretically utilized for the generation of power. The hot-dry-rock procedure can provide a flow of hot water. The considered binary system can transform the obtained thermal energy into electrical energy. The system makes use of a Rankine cycle with a working fluid having a low boiling point. Heat from the hot water is transferred to the working fluid. The present investigation is concerned with the development of a method for the calculation of the entire process. The results obtained with the computational method are to provide a basis for the determination of the operational characteristics. The development method is used for the study of a process based on the use of carbon dioxide as working fluid. The economics of a use of the hot-dry-rock process with the binary system is also investigated. It is found that the considered procedure is not economical. Economical operation requires, in particular, hot water supplied at a much lower cost.

Storage and growth of denitrifiers in aerobic granules: part I. model development.

PubMed

Ni, Bing-Jie; Yu, Han-Qing

2008-02-01

A mathematical model, based on the Activated Sludge Model No.3 (ASM3), is developed to describe the storage and growth activities of denitrifiers in aerobic granules under anoxic conditions. In this model, mass transfer, hydrolysis, simultaneous anoxic storage and growth, anoxic maintenance, and endogenous decay are all taken into account. The model established is implemented in the well-established AQUASIM simulation software. A combination of completely mixed reactor and biofilm reactor compartments provided by AQUASIM is used to simulate the mass transport and conversion processes occurring in both bulk liquid and granules. The modeling results explicitly show that the external substrate is immediately utilized for storage and growth at feast phase. More external substrates are diverted to storage process than the primary biomass production process. The model simulation indicates that the nitrate utilization rate (NUR) of granules-based denitrification process includes four linear phases of nitrate reduction. Furthermore, the methodology for determining the most important parameter in this model, that is, anoxic reduction factor, is established. (c) 2007 Wiley Periodicals, Inc.

Automated processing of first-pass radioisotope ventriculography data to determine essential central circulation parameters

NASA Astrophysics Data System (ADS)

Krotov, Aleksei; Pankin, Victor

2017-09-01

The assessment of central circulation (including heart function) parameters is vital in the preventive diagnostics of inherent and acquired heart failures and during polychemotherapy. The protocols currently applied in Russia do not fully utilize the first-pass assessment (FPRNA) and that results in poor data formalization, while the FPRNA is the one of the fastest, affordable and compact methods among other radioisotope diagnostics protocols. A non-imaging algorithm basing on existing protocols has been designed to use the readings of an additional detector above vena subclavia to determine the total blood volume (TBV), not requiring blood sampling in contrast to current protocols. An automated processing of precordial detector readings is presented, in order to determine the heart strike volume (SV). Two techniques to estimate the ejection fraction (EF) of the heart are discussed.

Measurements of admittances and characteristic combustion times of reactive gaseous propellant coaxial injectors

NASA Technical Reports Server (NTRS)

Janardan, B. A.; Daniel, B. R.; Zinn, B. T.

1979-01-01

The results of an experimental investigation that was concerned with the quantitative determination of the capabilities of combustion processes associated with coaxial injectors to amplify and sustain combustor oscillations was described. The driving provided by the combustion process was determined by employing the modified standing-wave method utilizing coaxial injectors and air-acetylene mixtures. Analyses of the measured data indicate that the investigated injectors are capable of initiating and amplifying combustion instabilities under favorable conditions of injector-combustion coupling and over certain frequency ranges. These frequency ranges and the frequency at which an injector's driving capacity is maximum are observed to depend upon the equivalence ratio, the pressure drop across the injector orifices and the number of injector elements. The characteristic combustion times of coaxial injectors were determined from steady state temperature measurements.

Network formation: neighborhood structures, establishment costs, and distributed learning.

PubMed

Chasparis, Georgios C; Shamma, Jeff S

2013-12-01

We consider the problem of network formation in a distributed fashion. Network formation is modeled as a strategic-form game, where agents represent nodes that form and sever unidirectional links with other nodes and derive utilities from these links. Furthermore, agents can form links only with a limited set of neighbors. Agents trade off the benefit from links, which is determined by a distance-dependent reward function, and the cost of maintaining links. When each agent acts independently, trying to maximize its own utility function, we can characterize “stable” networks through the notion of Nash equilibrium. In fact, the introduced reward and cost functions lead to Nash equilibria (networks), which exhibit several desirable properties such as connectivity, bounded-hop diameter, and efficiency (i.e., minimum number of links). Since Nash networks may not necessarily be efficient, we also explore the possibility of “shaping” the set of Nash networks through the introduction of state-based utility functions. Such utility functions may represent dynamic phenomena such as establishment costs (either positive or negative). Finally, we show how Nash networks can be the outcome of a distributed learning process. In particular, we extend previous learning processes to so-called “state-based” weakly acyclic games, and we show that the proposed network formation games belong to this class of games.

Adaptive Resource Utilization Prediction System for Infrastructure as a Service Cloud.

PubMed

Zia Ullah, Qazi; Hassan, Shahzad; Khan, Gul Muhammad

2017-01-01

Infrastructure as a Service (IaaS) cloud provides resources as a service from a pool of compute, network, and storage resources. Cloud providers can manage their resource usage by knowing future usage demand from the current and past usage patterns of resources. Resource usage prediction is of great importance for dynamic scaling of cloud resources to achieve efficiency in terms of cost and energy consumption while keeping quality of service. The purpose of this paper is to present a real-time resource usage prediction system. The system takes real-time utilization of resources and feeds utilization values into several buffers based on the type of resources and time span size. Buffers are read by R language based statistical system. These buffers' data are checked to determine whether their data follows Gaussian distribution or not. In case of following Gaussian distribution, Autoregressive Integrated Moving Average (ARIMA) is applied; otherwise Autoregressive Neural Network (AR-NN) is applied. In ARIMA process, a model is selected based on minimum Akaike Information Criterion (AIC) values. Similarly, in AR-NN process, a network with the lowest Network Information Criterion (NIC) value is selected. We have evaluated our system with real traces of CPU utilization of an IaaS cloud of one hundred and twenty servers.

Adaptive Resource Utilization Prediction System for Infrastructure as a Service Cloud

PubMed Central

Hassan, Shahzad; Khan, Gul Muhammad

2017-01-01

Infrastructure as a Service (IaaS) cloud provides resources as a service from a pool of compute, network, and storage resources. Cloud providers can manage their resource usage by knowing future usage demand from the current and past usage patterns of resources. Resource usage prediction is of great importance for dynamic scaling of cloud resources to achieve efficiency in terms of cost and energy consumption while keeping quality of service. The purpose of this paper is to present a real-time resource usage prediction system. The system takes real-time utilization of resources and feeds utilization values into several buffers based on the type of resources and time span size. Buffers are read by R language based statistical system. These buffers' data are checked to determine whether their data follows Gaussian distribution or not. In case of following Gaussian distribution, Autoregressive Integrated Moving Average (ARIMA) is applied; otherwise Autoregressive Neural Network (AR-NN) is applied. In ARIMA process, a model is selected based on minimum Akaike Information Criterion (AIC) values. Similarly, in AR-NN process, a network with the lowest Network Information Criterion (NIC) value is selected. We have evaluated our system with real traces of CPU utilization of an IaaS cloud of one hundred and twenty servers. PMID:28811819

Robust high-throughput batch screening method in 384-well format with optical in-line resin quantification.

PubMed

Kittelmann, Jörg; Ottens, Marcel; Hubbuch, Jürgen

2015-04-15

High-throughput batch screening technologies have become an important tool in downstream process development. Although continuative miniaturization saves time and sample consumption, there is yet no screening process described in the 384-well microplate format. Several processes are established in the 96-well dimension to investigate protein-adsorbent interactions, utilizing between 6.8 and 50 μL resin per well. However, as sample consumption scales with resin volumes and throughput scales with experiments per microplate, they are limited in costs and saved time. In this work, a new method for in-well resin quantification by optical means, applicable in the 384-well format, and resin volumes as small as 0.1 μL is introduced. A HTS batch isotherm process is described, utilizing this new method in combination with optical sample volume quantification for screening of isotherm parameters in 384-well microplates. Results are qualified by confidence bounds determined by bootstrap analysis and a comprehensive Monte Carlo study of error propagation. This new approach opens the door to a variety of screening processes in the 384-well format on HTS stations, higher quality screening data and an increase in throughput. Copyright © 2015 Elsevier B.V. All rights reserved.

Empowering occupational therapists to become evidence-based work rehabilitation practitioners.

PubMed

Vachon, Brigitte; Durand, Marie-José; LeBlanc, Jeannette

2010-01-01

Occupational therapists (OTs) engage in continuing education to integrate best available knowledge and skills into their practice. However, many barriers influence the degree to which they are currently able to integrate research evidence into their clinical decision making process. The specific objectives were to explore the clinical decision-making processes they used, and to describe the empowerment process they developed to become evidence-based practitioners. Eight OTs, who had attended a four-day workshop on evidence-based work rehabilitation, were recruited to participate to a reflective practice group. A collaborative research methodology was used. The group was convened for 12 meetings and held during a 15-month period. The data collected was analyzed using the grounded theory method. The results revealed the different decision-making modes used by OTs: defensive, repressed, cautious, autonomous intuitive and autonomous thoughtful. These modes influenced utilization of evidence and determined the stances taken toward practice change. Reflective learning facilitated their utilization of an evidence-based practice model through a three-level empowerment process: deliberateness, client-centeredness and system mindedness. During the course of this study, participants learned to become evidence-based practitioners. This process had an impact on how they viewed their clients, their practice and the work rehabilitation system.

Impact of Lumbar Fusion on Health Care Resource Utilization.

PubMed

Mina, Curtis; Carreon, Leah Y; Glassman, Steven D

2016-02-01

A longitudinal cohort. The aim of this study was to determine the extent of health care resource utilization decrease 2 years after lumbar spinal fusion. Despite the assumption that surgery will minimize the need for ongoing nonsurgical treatment, the impact of lumbar fusion on subsequent health care resource utilization has not been effectively studied. Patients who had continuous coverage by a major insurer during the year before decompression and posterolateral instrumented spinal fusion, and the 2 and a half years following were identified. All charges processed during this time-period were collected. Charges associated with the index surgery, the 90-day postoperative period, and those unrelated to spinal care were excluded. Associations with Oswestry Disability Index (ODI) score improvement at 2 years after surgery and health care resource utilization were determined. Sixty-six patients were included in the analysis. The mean age was 59 years and 39% were males. There was a decrease in health care utilization costs 1 year after surgery ($3267.59) compared with pre-op ($4246.32), but this was not statistically significant (P = 0.197). There was a statistically significant decrease in costs during the second year after surgery ($1420.97) compared with either pre-op (P = 0.000) or 1-year costs (P = 0.001). No statistically significant correlations could be found between change in ODI scores and costs incurred at either year post-op. Health care utilization decreased at 1 year and significantly at 2 years after lumbar fusion. However, there was no correlation between use of nonsurgical resources and clinical outcome based on ODI scores. This raises the question as to whether these resources were used in a rational manner. This cooperative study between a major insurer and a tertiary spine center provides improved insight into the cost profile of lumbar fusion surgery. Further study is needed to determine whether ongoing post-op treatment is necessary or simply established practice. 2.

Handbook of evaluation of utility DSM programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirst, E.; Reed, J.; Bronfman, B.

Program evaluation has become a central issue in the world of utility integrated resource planning. The DSM programs that utilities were operating to meet federal requirements or to improve customer relations are now becoming big business. DSM is being considered an important resource in a utility`s portfolio of options. In the last five years, the amount of money that utilities have invested in DSM has grown exponentially in most regulatory jurisdictions. Market analysts are now talking about DSM being a $30 billion industry by the end of the decade. If the large volume of DSM-program investments was not enough tomore » highlight the importance of evaluation, then the introduction of regulatory incentives has really focused the spotlight. This handbook was developed through a process that involved many of those people who represent the diverse constituencies of DSM-program evaluation. We have come to recognize the many technical disciplines that must be employed to evaluate DSM programs. An analysis might start out based on the principles of utility load research to find out what happened, but a combination of engineering and statistical methods must be used to ``triangulate`` an estimate of what would have happened without the program. The difference, of course, is that elusive but prized result of evaluation: what happened as the direct result of the DSM program. Technical performance of DSM measures is not the sole determinant of the answer, either. We also recognize the importance of such behavioral attributes of DSM as persistence and free ridership. Finally, DSM evaluation is meaningless without attention to planning an approach, communicating results to relevant decision-makers, and focusing as much on the process as the impacts of the program. These topics are all covered in this handbook.« less

Determination of Specific Forces and Tool Deflections in Micro-milling of Ti-6Al-4V alloy using Finite Element Simulations and Analysis

NASA Astrophysics Data System (ADS)

Farina, Simone; Thepsonti, Thanongsak; Ceretti, Elisabetta; Özel, Tugrul

2011-05-01

Titanium alloys offer superb properties in strength, corrosion resistance and biocompatibility and are commonly utilized in medical devices and implants. Micro-end milling process is a direct and rapid fabrication method for manufacturing medical devices and implants in titanium alloys. Process performance and quality depend upon an understanding of the relationship between cutting parameters and forces and resultant tool deflections to avoid tool breakage. For this purpose, FE simulations of chip formation during micro-end milling of Ti-6Al-4V alloy with an ultra-fine grain solid carbide two-flute micro-end mill are investigated using DEFORM software. At first, specific forces in tangential and radial directions of cutting during micro-end milling for varying feed advance and rotational speeds have been determined using designed FE simulations for chip formation process. Later, these forces are applied to the micro-end mill geometry along the axial depth of cut in 3D analysis of ABAQUS. Consequently, 3D distributions for tool deflections & von Misses stress are determined. These analyses will yield in establishing integrated multi-physics process models for high performance micro-end milling and a leap-forward to process improvements.

A holistic framework for design of cost-effective minimum water utilization network.

PubMed

Wan Alwi, S R; Manan, Z A; Samingin, M H; Misran, N

2008-07-01

Water pinch analysis (WPA) is a well-established tool for the design of a maximum water recovery (MWR) network. MWR, which is primarily concerned with water recovery and regeneration, only partly addresses water minimization problem. Strictly speaking, WPA can only lead to maximum water recovery targets as opposed to the minimum water targets as widely claimed by researchers over the years. The minimum water targets can be achieved when all water minimization options including elimination, reduction, reuse/recycling, outsourcing and regeneration have been holistically applied. Even though WPA has been well established for synthesis of MWR network, research towards holistic water minimization has lagged behind. This paper describes a new holistic framework for designing a cost-effective minimum water network (CEMWN) for industry and urban systems. The framework consists of five key steps, i.e. (1) Specify the limiting water data, (2) Determine MWR targets, (3) Screen process changes using water management hierarchy (WMH), (4) Apply Systematic Hierarchical Approach for Resilient Process Screening (SHARPS) strategy, and (5) Design water network. Three key contributions have emerged from this work. First is a hierarchical approach for systematic screening of process changes guided by the WMH. Second is a set of four new heuristics for implementing process changes that considers the interactions among process changes options as well as among equipment and the implications of applying each process change on utility targets. Third is the SHARPS cost-screening technique to customize process changes and ultimately generate a minimum water utilization network that is cost-effective and affordable. The CEMWN holistic framework has been successfully implemented on semiconductor and mosque case studies and yielded results within the designer payback period criterion.

Application of dual-fuel propulsion to a single stage AMLS vehicle

NASA Technical Reports Server (NTRS)

Lepsch, Roger A., Jr.; Stanley, Douglas O.; Unal, Resit

1993-01-01

As part of NASA's Advanced Manned Launch System (AMLS) study to determine a follow-on, or complement, to the Space Shuttle, a reusable single-stage-to-orbit concept utilizing dual-fuel rocket propulsion has been examined. Several dual-fuel propulsion concepts were investigated. These include: a separate engine concept combining Russian RD-170 kerosene-fueled engines with SSME-derivative engines; the kerosene and hydrogen-fueled Russian RD-701 engine concept; and a dual-fuel, dual-expander engine concept. Analysis to determine vehicle weight and size characteristics was performed using conceptual level design techniques. A response surface methodology for multidisciplinary design was utilized to optimize the dual-fuel vehicle concepts with respect to several important propulsion system and vehicle design parameters in order to achieve minimum empty weight. Comparisons were then made with a hydrogen-fueled reference, single-stage vehicle. The tools and methods employed in the analysis process are also summarized.

Educational Innovation in the United States. Volume 1: The National Survey: The Substance and the Process.

ERIC Educational Resources Information Center

Havelock, Ronald G.; And Others

This document reports on a project undertaken to determine the feasibility of a periodic national survey of a sample of U.S. school districts to obtain information on the performance of the existing dissemination and utilization network for educational innovations. The first section of volume 1 describes the content and consequences of innovation,…

Survey of New Jersey Public School Districts Using Computers and Data Entry Equipment.

ERIC Educational Resources Information Center

Gaydos, Irvin A.

The twelve tables in this study represent the results of a Fall 1975 survey of the 589 operating school districts in the State of New Jersey to determine the status of computer and data entry equipment utilization. Results show that the number of users of this equipment increased noticeably, primarily in administrative processing areas such as…

A Developmental Study of Conceptual, Semantic Differential, and Acoustical Dimensions as Encoding Categories in Short-Term Memory. Final Report.

ERIC Educational Resources Information Center

Pender, Nola J.

The purpose of this research was to investigate developmental changes in encoding processes. It attempted to determine the extent to which children of varying ages utilize semantic (denotative or connotative) and acoustical encoding categories in a short-term memory task. It appears to be a reasonable assumption that as associational hierarchies…

Baseline studies on the feasibility of detecting a coal/shale interface with a self-powered sensitized pick

NASA Technical Reports Server (NTRS)

Anderson, G. R., II

1981-01-01

The feasibility of utilizing a sensitized pick to discriminate between cutting coal and roof material during the longwall mining process was investigated. A conventional longwall mining pick was instrumented and cutting force magnitudes were determined for a variety of materials, including Illinois #6 coal, shale type materials, and synthetic coal/shale materials.

Funding Solar Projects at Federal Agencies: Mechanisms and Selection Criteria (Brochure)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Implementing solar energy projects at federal facilities is a process. The project planning phase of the process includes determining goals, building a team, determining site feasibility and selecting the appropriate project funding tool. This fact sheet gives practical guidance to assist decision-makers with understanding and selecting the funding tool that would best address their site goals. Because project funding tools are complex, federal agencies should seek project assistance before making final decisions. High capital requirements combined with limits on federal agency energy contracts create challenges for funding solar projects. Solar developers typically require long-term contracts (15-20) years to spread outmore » the initial investment and to enable payments similar to conventional utility bill payments. In the private sector, 20-year contracts have been developed, vetted, and accepted, but the General Services Administration (GSA) contract authority (federal acquisition regulation [FAR] part 41) typically limits contract terms to 10 years. Payments on shorter-term contracts make solar economically unattractive compared with conventional generation. However, in several instances, the federal sector has utilized innovative funding tools that allow long-term contracts or has created a project package that is economically attractive within a shorter contract term.« less

Molecular Monte Carlo Simulations Using Graphics Processing Units: To Waste Recycle or Not?

PubMed

Kim, Jihan; Rodgers, Jocelyn M; Athènes, Manuel; Smit, Berend

2011-10-11

In the waste recycling Monte Carlo (WRMC) algorithm, (1) multiple trial states may be simultaneously generated and utilized during Monte Carlo moves to improve the statistical accuracy of the simulations, suggesting that such an algorithm may be well posed for implementation in parallel on graphics processing units (GPUs). In this paper, we implement two waste recycling Monte Carlo algorithms in CUDA (Compute Unified Device Architecture) using uniformly distributed random trial states and trial states based on displacement random-walk steps, and we test the methods on a methane-zeolite MFI framework system to evaluate their utility. We discuss the specific implementation details of the waste recycling GPU algorithm and compare the methods to other parallel algorithms optimized for the framework system. We analyze the relationship between the statistical accuracy of our simulations and the CUDA block size to determine the efficient allocation of the GPU hardware resources. We make comparisons between the GPU and the serial CPU Monte Carlo implementations to assess speedup over conventional microprocessors. Finally, we apply our optimized GPU algorithms to the important problem of determining free energy landscapes, in this case for molecular motion through the zeolite LTA.

A risk-based approach to management of leachables utilizing statistical analysis of extractables.

PubMed

Stults, Cheryl L M; Mikl, Jaromir; Whelehan, Oliver; Morrical, Bradley; Duffield, William; Nagao, Lee M

2015-04-01

To incorporate quality by design concepts into the management of leachables, an emphasis is often put on understanding the extractable profile for the materials of construction for manufacturing disposables, container-closure, or delivery systems. Component manufacturing processes may also impact the extractable profile. An approach was developed to (1) identify critical components that may be sources of leachables, (2) enable an understanding of manufacturing process factors that affect extractable profiles, (3) determine if quantitative models can be developed that predict the effect of those key factors, and (4) evaluate the practical impact of the key factors on the product. A risk evaluation for an inhalation product identified injection molding as a key process. Designed experiments were performed to evaluate the impact of molding process parameters on the extractable profile from an ABS inhaler component. Statistical analysis of the resulting GC chromatographic profiles identified processing factors that were correlated with peak levels in the extractable profiles. The combination of statistically significant molding process parameters was different for different types of extractable compounds. ANOVA models were used to obtain optimal process settings and predict extractable levels for a selected number of compounds. The proposed paradigm may be applied to evaluate the impact of material composition and processing parameters on extractable profiles and utilized to manage product leachables early in the development process and throughout the product lifecycle.

Method Development for Clinical Comprehensive Evaluation of Pediatric Drugs Based on Multi-Criteria Decision Analysis: Application to Inhaled Corticosteroids for Children with Asthma.

PubMed

Yu, Yuncui; Jia, Lulu; Meng, Yao; Hu, Lihua; Liu, Yiwei; Nie, Xiaolu; Zhang, Meng; Zhang, Xuan; Han, Sheng; Peng, Xiaoxia; Wang, Xiaoling

2018-04-01

Establishing a comprehensive clinical evaluation system is critical in enacting national drug policy and promoting rational drug use. In China, the 'Clinical Comprehensive Evaluation System for Pediatric Drugs' (CCES-P) project, which aims to compare drugs based on clinical efficacy and cost effectiveness to help decision makers, was recently proposed; therefore, a systematic and objective method is required to guide the process. An evidence-based multi-criteria decision analysis model that involved an analytic hierarchy process (AHP) was developed, consisting of nine steps: (1) select the drugs to be reviewed; (2) establish the evaluation criterion system; (3) determine the criterion weight based on the AHP; (4) construct the evidence body for each drug under evaluation; (5) select comparative measures and calculate the original utility score; (6) place a common utility scale and calculate the standardized utility score; (7) calculate the comprehensive utility score; (8) rank the drugs; and (9) perform a sensitivity analysis. The model was applied to the evaluation of three different inhaled corticosteroids (ICSs) used for asthma management in children (a total of 16 drugs with different dosage forms and strengths or different manufacturers). By applying the drug analysis model, the 16 ICSs under review were successfully scored and evaluated. Budesonide suspension for inhalation (drug ID number: 7) ranked the highest, with comprehensive utility score of 80.23, followed by fluticasone propionate inhaled aerosol (drug ID number: 16), with a score of 79.59, and budesonide inhalation powder (drug ID number: 6), with a score of 78.98. In the sensitivity analysis, the ranking of the top five and lowest five drugs remains unchanged, suggesting this model is generally robust. An evidence-based drug evaluation model based on AHP was successfully developed. The model incorporates sufficient utility and flexibility for aiding the decision-making process, and can be a useful tool for the CCES-P.

A methodology for comprehensive strategic planning and program prioritization

NASA Astrophysics Data System (ADS)

Raczynski, Christopher Michael

2008-10-01

This process developed in this work, Strategy Optimization for the Allocation of Resources (SOAR), is a strategic planning methodology based off Integrated Product and Process Development and systems engineering techniques. Utilizing a top down approach, the process starts with the creation of the organization vision and its measures of effectiveness. These measures are prioritized based on their application to external world scenarios which will frame the future. The programs which will be used to accomplish this vision are identified by decomposing the problem. Information is gathered on the programs as to the application, cost, schedule, risk, and other pertinent information. The relationships between the levels of the hierarchy are mapped utilizing subject matter experts. These connections are then utilized to determine the overall benefit of the programs to the vision of the organization. Through a Multi-Objective Genetic Algorithm a tradespace of potential program portfolios can be created amongst which the decision maker can allocate resources. The information and portfolios are presented to the decision maker through the use of a Decision Support System which collects and visualizes all the data in a single location. This methodology was tested utilizing a science and technology planning exercise conducted by the United States Navy. A thorough decomposition was defined and technology programs identified which had the potential to provide benefit to the vision. The prioritization of the top level capabilities was performed through the use of a rank ordering scheme and a previous naval application was used to demonstrate a cumulative voting scheme. Voting was performed utilizing the Nominal Group Technique to capture the relationships between the levels of the hierarchy. Interrelationships between the technologies were identified and a MOGA was utilized to optimize portfolios with respect to these constraints and information was placed in a DSS. This formulation allowed the decision makers to assess which portfolio could provide the greatest benefit to the Navy while still fitting within the funding profile.

Height Control and Deposition Measurement for the Electron Beam Free Form Fabrication (EBF3) Process

NASA Technical Reports Server (NTRS)

Hafley, Robert A. (Inventor); Seufzer, William J. (Inventor)

2017-01-01

A method of controlling a height of an electron beam gun and wire feeder during an electron freeform fabrication process includes utilizing a camera to generate an image of the molten pool of material. The image generated by the camera is utilized to determine a measured height of the electron beam gun relative to the surface of the molten pool. The method further includes ensuring that the measured height is within the range of acceptable heights of the electron beam gun relative to the surface of the molten pool. The present invention also provides for measuring a height of a solid metal deposit formed upon cooling of a molten pool. The height of a single point can be measured, or a plurality of points can be measured to provide 2D or 3D surface height measurements.

Use of remote sensing technology for inventorying and planning utilization of land resources in South Dakota

NASA Technical Reports Server (NTRS)

1974-01-01

A comprehensive land use planning process model is being developed in Meade County, South Dakota, using remote sensing technology. The proper role of remote sensing in the land use planning process is being determined by interaction of remote sensing specialists with local land use planners. The data that were collected by remote sensing techniques are as follows: (1) level I land use data interpreted at a scale of 1:250,000 from false color enlargement prints of ERTS-1 color composite transparencies; (2) detailed land use data interpreted at a scale of 1:24,000 from enlargement color prints of high altitude RB-57 photography; and (3) general soils map interpreted at a scale of 1:250,000 from false color enlargement prints of ERTS-1 color composite transparencies. In addition to use of imagery as an interpretation aid, the utility of using photographs as base maps was demonstrated.

Understanding the behavior of Giardia and Cryptosporidium in an urban watershed: Explanation and application of techniques to collect and evaluate monitoring data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crockett, C.S.; Haas, C.N.

1996-11-01

Due to current proposed regulations requiring monitoring for protozoans and demonstration of adequate protozoan removal depending on source water concentrations detected, many utilities are considering or are engaged in protozoan monitoring activities within their watershed so that proper watershed management and treatment modifications can reduce their impact on drinking water safety and quality. However, due to the difficulties associated with the current analytical methods and sample collection many sampling efforts collect data that cannot be interpreted or lack the tools to interpret the information obtained. Therefore, it is necessary to determine how to develop an effective sampling program tailored tomore » a utility`s specific needs to provide interpretable data and develop tools for evaluating such data. The following case study describes the process in which a utility learned how to collect and interpret monitoring data for their specific needs and provides concepts and tools which other utilities can use to aid in their own macro and microwatershed management efforts.« less

Angular analysis of B → J/ψK1: Towards a model independent determination of the photon polarization with B → K1γ

NASA Astrophysics Data System (ADS)

Kou, E.; Le Yaouanc, A.; Tayduganov, A.

2016-12-01

We propose a model independent extraction of the hadronic information needed to determine the photon polarization of the b → sγ process by the method utilizing the B →K1 γ → Kππγ angular distribution. We show that exactly the same hadronic information can be obtained by using the B → J / ψK1 → J / ψKππ channel, which leads to a much higher precision.

UV-Vis as quantification tool for solubilized lignin following a single-shot steam process.

PubMed

Lee, Roland A; Bédard, Charles; Berberi, Véronique; Beauchet, Romain; Lavoie, Jean-Michel

2013-09-01

In this short communication, UV/Vis was used as an analytical tool for the quantification of lignin concentrations in aqueous mediums. A significant correlation was determined between absorbance and concentration of lignin in solution. For this study, lignin was produced from different types of biomasses (willow, aspen, softwood, canary grass and hemp) using steam processes. Quantification was performed at 212, 225, 237, 270, 280 and 287 nm. UV-Vis quantification of lignin was found suitable for different types of biomass making this a timesaving analytical system that could lead to uses as Process Analytical Tool (PAT) in biorefineries utilizing steam processes or comparable approaches. Copyright © 2013 Elsevier Ltd. All rights reserved.

Operational applications of satellite snowcover observations in Rio Grande drainage of Colorado

NASA Technical Reports Server (NTRS)

Washicheck, J. N.; Mikesell, T.

1975-01-01

Various mapping techniques were tried and evaluated. There were many problems encountered such as distinquishing clouds from snow and snow under trees. A partial solution to some of the problems involves ground reconnaissance and low air flights. Snow areas, cloud cover, and total areas were planimetered after transferring imagery by use of zoom transfer scope. These determinations were then compared to areas determined by use of a density slicer. Considerable adjustment is required for these two values to compare. NOAA pictures were also utilized in the evaluation. Forest cover is one of the parameters used in the modeling process. The determination of this percentage is being explored.

Assessment of MSFCs Process for the Development and Activation of Space Act Agreements

NASA Technical Reports Server (NTRS)

Daugherty, Rachel A.

2014-01-01

A Space Act Agreement (SAA) is a contractual vehicle that NASA utilizes to form partnerships with non-NASA entities to stimulate cutting-edge innovation within the science and technology communities while concurrently supporting the NASA missions. SAAs are similar to traditional contracts in that they involve the commitment of Agency resources but allow more flexibility and are more cost effective to implement than traditional contracts. Consequently, the use of SAAs to develop partnerships has greatly increased over the past several years. To facilitate this influx of SAAs, Marshall Space Flight Center (MSFC) developed a process during a kaizen event to streamline and improve the quality of SAAs developed at the Center level. This study assessed the current SAA process to determine if improvements could be implemented to increase productivity, decrease time to activation, and improve the quality of deliverables. Using a combination of direct procedural observation, personnel interviews, and statistical analysis, elements of the process in need of remediation were identified and potential solutions developed. The findings focus primarily on the difficulties surrounding tracking and enforcing process adherence and communication issues among stakeholders. Potential solutions include utilizing customer relationship management (CRM) software to facilitate process coordination and co-locating or potentially merging the two separate organizations involved in SAA development and activation at MSFC.

Proposal and design of a natural gas liquefaction process recovering the energy obtained from the pressure reducing stations of high-pressure pipelines

NASA Astrophysics Data System (ADS)

Tan, Hongbo; Zhao, Qingxuan; Sun, Nannan; Li, Yanzhong

2016-12-01

Taking advantage of the refrigerating effect in the expansion at an appropriate temperature, a fraction of high-pressure natural gas transported by pipelines could be liquefied in a city gate station through a well-organized pressure reducing process without consuming any extra energy. The authors proposed such a new process, which mainly consists of a turbo-expander driven booster, throttle valves, multi-stream heat exchangers and separators, to yield liquefied natural gas (LNG) and liquid light hydrocarbons (LLHs) utilizing the high-pressure of the pipelines. Based on the assessment of the effects of several key parameters on the system performance by a steady-state simulation in Aspen HYSYS, an optimal design condition of the proposed process was determined. The results showed that the new process is more appropriate to be applied in a pressure reducing station (PRS) for the pipelines with higher pressure. For the feed gas at the pressure of 10 MPa, the maximum total liquefaction rate (ytot) of 15.4% and the maximum exergy utilizing rate (EUR) of 21.7% could be reached at the optimal condition. The present process could be used as a small-scale natural gas liquefying and peak-shaving plant at a city gate station.

Assessment of Chicken Carcass Microbiome Responses During Processing in the Presence of Commercial Antimicrobials Using a Next Generation Sequencing Approach

PubMed Central

Ae Kim, Sun; Hong Park, Si; In Lee, Sang; Owens, Casey M.; Ricke, Steven C.

2017-01-01

The purpose of this study was to 1) identify microbial compositional changes on chicken carcasses during processing, 2) determine the antimicrobial efficacy of peracetic acid (PAA) and Amplon (blend of sulfuric acid and sodium sulfate) at a poultry processing pilot plant scale, and 3) compare microbial communities between chicken carcass rinsates and recovered bacteria from media. Birds were collected from each processing step and rinsates were applied to estimate aerobic plate count (APC) and Campylobacter as well as Salmonella prevalence. Microbiome sequencing was utilized to identify microbial population changes over processing and antimicrobial treatments. Only the PAA treatment exhibited significant reduction of APC at the post chilling step while both Amplon and PAA yielded detectable Campylobacter reductions at all steps. Based on microbiome sequencing, Firmicutes were the predominant bacterial group at the phyla level with over 50% frequency in all steps while the relative abundance of Proteobacteria decreased as processing progressed. Overall microbiota between rinsate and APC plate microbial populations revealed generally similar patterns at the phyla level but they were different at the genus level. Both antimicrobials appeared to be effective on reducing problematic bacteria and microbiome can be utilized to identify optimal indicator microorganisms for enhancing product quality. PMID:28230180

Experimental determination of micromachined discrete and continuous device spring constants using nanoindentation method

NASA Astrophysics Data System (ADS)

Chan, M. L.; Tay, Francis E.; Logeeswaran, V. J.; Zeng, Kaiyang; Shen, Lu; Chau, Fook S.

2002-04-01

A rapid and accurate static and quasi-static method for determining the out-of-plane spring constraints of cantilevers and a micromachined vibratory sensor is presented. In the past, much of the effort in nanoindentation application was to investigate the thin-film mechanical properties. In this paper, we have utilized the nanoindentation method to measure directly some micromachined device (e.g. microgyroscope) spring constants. The cantilevers and devices tested were fabricated using the MUMPS process and an SOI process (patent pending). Spring constants are determined using a commercial nanoindentation apparatus UMIS-2000 configured with both Berkovich and spherical indenter tip that can be placed onto the device with high accuracy. Typical load resolution is 20micrometers N to 0.5N and a displacement resolution of 0.05nm. Information was deduced from the penetration depth versus load curves during both loading and unloading.

Orbit Determination and Navigation Software Testing for the Mars Reconnaissance Orbiter

NASA Technical Reports Server (NTRS)

Pini, Alex

2011-01-01

During the extended science phase of the Mars Reconnaissance Orbiter's lifecycle, the operational duties pertaining to navigation primarily involve orbit determination. The orbit determination process utilizes radiometric tracking data and is used for the prediction and reconstruction of MRO's trajectories. Predictions are done twice per week for ephemeris updates on-board the spacecraft and for planning purposes. Orbit Trim Maneuvers (OTM-s) are also designed using the predicted trajectory. Reconstructions, which incorporate a batch estimator, provide precise information about the spacecraft state to be synchronized with scientific measurements. These tasks were conducted regularly to validate the results obtained by the MRO Navigation Team. Additionally, the team is in the process of converting to newer versions of the navigation software and operating system. The capability to model multiple densities in the Martian atmosphere is also being implemented. However, testing outputs among these different configurations was necessary to ensure compliance to a satisfactory degree.

Application of remote sensors in coastal zone observations

NASA Technical Reports Server (NTRS)

Caillat, J. M.; Elachi, C.; Brown, W. E., Jr.

1975-01-01

A review of processes taking place along coastlines and their biological consideration led to the determination of the elements which are required in the study of coastal structures and which are needed for better utilization of the resources from the oceans. The processes considered include waves, currents, and their influence on the erosion of coastal structures. Biological considerations include coastal fisheries, estuaries, and tidal marshes. Various remote sensors were analyzed for the information which they can provide and sites were proposed where a general ocean-observation plan could be tested.

Process for combining multiple passes of interferometric SAR data

DOEpatents

Bickel, Douglas L.; Yocky, David A.; Hensley, Jr., William H.

2000-11-21

Interferometric synthetic aperture radar (IFSAR) is a promising technology for a wide variety of military and civilian elevation modeling requirements. IFSAR extends traditional two dimensional SAR processing to three dimensions by utilizing the phase difference between two SAR images taken from different elevation positions to determine an angle of arrival for each pixel in the scene. This angle, together with the two-dimensional location information in the traditional SAR image, can be transformed into geographic coordinates if the position and motion parameters of the antennas are known accurately.

Method and apparatus for measuring flow velocity using matched filters

DOEpatents

Raptis, A.C.

1983-09-06

An apparatus and method for measuring the flow velocities of individual phase flow components of a multiphase flow utilizes matched filters. Signals arising from flow noise disturbance are extracted from the flow, at upstream and downstream locations. The signals are processed through pairs of matched filters which are matched to the flow disturbance frequency characteristics of the phase flow component to be measured. The processed signals are then cross-correlated to determine the transit delay time of the phase flow component between sensing positions. 8 figs.

Lignin blockers and uses thereof

DOEpatents

Yang, Bin [West Lebanon, NH; Wyman, Charles E [Norwich, VT

2011-01-25

Disclosed is a method for converting cellulose in a lignocellulosic biomass. The method provides for a lignin-blocking polypeptide and/or protein treatment of high lignin solids. The treatment enhances cellulase availability in cellulose conversion and allows for the determination of optimized pretreatment conditions. Additionally, ethanol yields from a Simultaneous Saccharification and Fermentation process are improved 5-25% by treatment with a lignin-blocking polypeptide and/or protein. Thus, a more efficient and economical method of processing lignin containing biomass materials utilizes a polypeptide/protein treatment step that effectively blocks lignin binding of cellulase.

Development of a Nonlinear Soft-Sensor Using a GMDH Network for a Refinery Crude Distillation Tower

NASA Astrophysics Data System (ADS)

Fujii, Kenzo; Yamamoto, Toru

In atmospheric distillation processes, the stabilization of processes is required in order to optimize the crude-oil composition that corresponds to product market conditions. However, the process control systems sometimes fall into unstable states in the case where unexpected disturbances are introduced, and these unusual phenomena have had an undesirable affect on certain products. Furthermore, a useful chemical engineering model has not yet been established for these phenomena. This remains a serious problem in the atmospheric distillation process. This paper describes a new modeling scheme to predict unusual phenomena in the atmospheric distillation process using the GMDH (Group Method of Data Handling) network which is one type of network model. According to the GMDH network, the model structure can be determined systematically. However, the least squares method has been commonly utilized in determining weight coefficients (model parameters). Estimation accuracy is not entirely expected, because the sum of squared errors between the measured values and estimates is evaluated. Therefore, instead of evaluating the sum of squared errors, the sum of absolute value of errors is introduced and the Levenberg-Marquardt method is employed in order to determine model parameters. The effectiveness of the proposed method is evaluated by the foaming prediction in the crude oil switching operation in the atmospheric distillation process.

Utilizing a Health Impact Assessment (HIA) to Connect Natural ...

EPA Pesticide Factsheets

Marrying scientific and health research with natural resource management should be a straightforward process. However, differences in purpose, goals, language, levels of detail and implementation authority between the scientists who conduct research and resource managers who plan and implement projects make it difficult for resource managers to include information not specific to the problem at hand. One method to overcome this barrier is a Health Impact Assessment (HIA) or process that uses scientific data, health expertise and public input to factor public health considerations into the decision-making process. An HIA informs decision makers and stakeholders of the potential health effects of a proposed program, policy, project or plan through a systematic investigation of impacts to health and health determinants and deliberative engagement of community members and other stakeholders throughout the HIA process. USEPA will be conducting an HIA on the Minnesota Department of Natural Resources’ sediment remediation and habitat restoration project at Kingsbury Bay and Grassy Point. This poster outlines the HIA process, illustrates how technical and stakeholder committees inform the process, and presents the determinants of health that will be explored in the HIA. not applicable

Automated absolute phase retrieval in across-track interferometry

NASA Technical Reports Server (NTRS)

Madsen, Soren N.; Zebker, Howard A.

1992-01-01

Discussed is a key element in the processing of topographic radar maps acquired by the NASA/JPL airborne synthetic aperture radar configured as an across-track interferometer (TOPSAR). TOPSAR utilizes a single transmit and two receive antennas; the three-dimensional target location is determined by triangulation based on a known baseline and two measured slant ranges. The slant range difference is determined very accurately from the phase difference between the signals received by the two antennas. This phase is measured modulo 2pi, whereas it is the absolute phase which relates directly to the difference in slant range. It is shown that splitting the range bandwidth into two subbands in the processor and processing each individually allows for the absolute phase. The underlying principles and system errors which must be considered are discussed, together with the implementation and results from processing data acquired during the summer of 1991.

Efficient utilization of greenhouse gases in a gas-to-liquids process combined with CO2/steam-mixed reforming and Fe-based Fischer-Tropsch synthesis.

PubMed

Zhang, Chundong; Jun, Ki-Won; Ha, Kyoung-Su; Lee, Yun-Jo; Kang, Seok Chang

2014-07-15

Two process models for carbon dioxide utilized gas-to-liquids (GTL) process (CUGP) mainly producing light olefins and Fischer-Tropsch (F-T) synthetic oils were developed by Aspen Plus software. Both models are mainly composed of a reforming unit, an F-T synthesis unit and a recycle unit, while the main difference is the feeding point of fresh CO2. In the reforming unit, CO2 reforming and steam reforming of methane are combined together to produce syngas in flexible composition. Meanwhile, CO2 hydrogenation is conducted via reverse water gas shift on the Fe-based catalysts in the F-T synthesis unit to produce hydrocarbons. After F-T synthesis, the unreacted syngas is recycled to F-T synthesis and reforming units to enhance process efficiency. From the simulation results, it was found that the carbon efficiencies of both CUGP options were successfully improved, and total CO2 emissions were significantly reduced, compared with the conventional GTL processes. The process efficiency was sensitive to recycle ratio and more recycle seemed to be beneficial for improving process efficiency and reducing CO2 emission. However, the process efficiency was rather insensitive to split ratio (recycle to reforming unit/total recycle), and the optimum split ratio was determined to be zero.

a Metadata Based Approach for Analyzing Uav Datasets for Photogrammetric Applications

NASA Astrophysics Data System (ADS)

Dhanda, A.; Remondino, F.; Santana Quintero, M.

2018-05-01

This paper proposes a methodology for pre-processing and analysing Unmanned Aerial Vehicle (UAV) datasets before photogrammetric processing. In cases where images are gathered without a detailed flight plan and at regular acquisition intervals the datasets can be quite large and be time consuming to process. This paper proposes a method to calculate the image overlap and filter out images to reduce large block sizes and speed up photogrammetric processing. The python-based algorithm that implements this methodology leverages the metadata in each image to determine the end and side overlap of grid-based UAV flights. Utilizing user input, the algorithm filters out images that are unneeded for photogrammetric processing. The result is an algorithm that can speed up photogrammetric processing and provide valuable information to the user about the flight path.

Revisiting Zirconium: New Abundance Determinations with Improved Oscillator Strengths

NASA Astrophysics Data System (ADS)

Burris, Debra L.; Jones, M.; Nichols, R.

2006-12-01

The element Zirconium is produced via neutron capture (n-capture). It resides in the mass range where there is uncertainty about the production mechanism at early time. The rapid n-capture process (r-process) was believed to be responsible for the production, but no study (Burris et al 2000, Gilroy et al 1988 and others) has been able to successfully use the r-process to reproduce the abundance signature for elements in this mass range for metal-poor halo stars. It has been suggested (Sneden and Cowan 2003) that there may be an undiscovered component to the r-process. New transition probabilities for Zr II have been reported by Malcheva et al (2006). We utilize these values to make new abundance determinations for Zr in the Sun and the metal-poor halo star BD +17 3248. This work is supported in part by the AAS Small Grant Program, the Arkansas Space Grant Consortium and the UCA Undergraduate Research Council.

Application of threshold concepts to ecological management problems: occupancy of Golden Eagles in Denali National Park, Alaska: Chapter 5

USGS Publications Warehouse

Eaton, Mitchell J.; Martin, Julien; Nichols, James D.; McIntyre, Carol; McCluskie, Maggie C.; Schmutz, Joel A.; Lubow, Bruce L.; Runge, Michael C.; Edited by Guntenspergen, Glenn R.

2014-01-01

In this chapter, we demonstrate the application of the various classes of thresholds, detailed in earlier chapters and elsewhere, via an actual but simplified natural resource management case study. We intend our example to provide the reader with the ability to recognize and apply the theoretical concepts of utility, ecological and decision thresholds to management problems through a formalized decision-analytic process. Our case study concerns the management of human recreational activities in Alaska’s Denali National Park, USA, and the possible impacts of such activities on nesting Golden Eagles, Aquila chrysaetos. Managers desire to allow visitors the greatest amount of access to park lands, provided that eagle nesting-site occupancy is maintained at a level determined to be acceptable by the managers themselves. As these two management objectives are potentially at odds, we treat minimum desired occupancy level as a utility threshold which, then, serves to guide the selection of annual management alternatives in the decision process. As human disturbance is not the only factor influencing eagle occupancy, we model nesting-site dynamics as a function of both disturbance and prey availability. We incorporate uncertainty in these dynamics by considering several hypotheses, including a hypothesis that site occupancy is affected only at a threshold level of prey abundance (i.e., an ecological threshold effect). By considering competing management objectives and accounting for two forms of thresholds in the decision process, we are able to determine the optimal number of annual nesting-site restrictions that will produce the greatest long-term benefits for both eagles and humans. Setting a utility threshold of 75 occupied sites, out of a total of 90 potential nesting sites, the optimization specified a decision threshold at approximately 80 occupied sites. At the point that current occupancy falls below 80 sites, the recommended decision is to begin restricting access to humans; above this level, it is recommended that all eagle territories be opened to human recreation. We evaluated the sensitivity of the decision threshold to uncertainty in system dynamics and to management objectives (i.e., to the utility threshold).

Physician utilization and expenditures in a Medicaid Population

PubMed Central

Buczko, William

1986-01-01

The determinants of physician visit utilization and expenditures for the full-year Medicaid enrollees in the State Medicaid household survey portion of the National Medical Care Utilization and Expenditure Survey are analyzed in this article. The regression analyses for the probability of a physician visit, for number of physician visits, and for physician visit expenditures underscore the importance of perceived health status as a determinant of both physician utilization and expenditures. Other important determinants of physician utilization and expenditures were regular source of care, State, enrollment group, sex, and family size. PMID:10312009

Investigating Science Student Teachers' Ideas about Function and Anatomical Form of Two Human Sensory Organs, the Eye and the Ear

ERIC Educational Resources Information Center

Kunt, Halil

2016-01-01

The purpose of this research was to determine science student teachers' level of knowledge about the anatomical structure of two sensory organs, the eye and the ear, in addition to vision and hearing processes. Conducted with 86 science student teachers, research utilized drawing methods and open-ended questions as data collection instruments. The…

Design concepts for a composite door frame system for general automotive applications

NASA Technical Reports Server (NTRS)

Tauber, J. A.

1976-01-01

Conceptual design, manufacturing process, and costs are explored to determine the feasibility of replacing present steel parts in automotive door structures with various composite materials. The problems of conforming to present anti-intrusion specifications with advanced materials are examined and discussed. Modest weight reductions, at competitive costs, were identified for the utilization of specific composite materials in automotive door structures.

An Action Research Project to Determine the Utility of Bully Prevention in Positive Behavior Support for Elementary School Bullying Prevention

ERIC Educational Resources Information Center

Goodman-Scott, Emily; Doyle, Beth; Brott, Pamelia

2014-01-01

A trio of researchers presents a case study from a practical, participatory action research project to demonstrate how one school district implemented a school-wide bullying prevention initiative for all elementary schools based on Bully Prevention in Positive Behavior Support (BP-PBS). The purpose of this manuscript is to discuss the process of…

Utility-based early modulation of processing distracting stimulus information.

PubMed

Wendt, Mike; Luna-Rodriguez, Aquiles; Jacobsen, Thomas

2014-12-10

Humans are selective information processors who efficiently prevent goal-inappropriate stimulus information to gain control over their actions. Nonetheless, stimuli, which are both unnecessary for solving a current task and liable to cue an incorrect response (i.e., "distractors"), frequently modulate task performance, even when consistently paired with a physical feature that makes them easily discernible from target stimuli. Current models of cognitive control assume adjustment of the processing of distractor information based on the overall distractor utility (e.g., predictive value regarding the appropriate response, likelihood to elicit conflict with target processing). Although studies on distractor interference have supported the notion of utility-based processing adjustment, previous evidence is inconclusive regarding the specificity of this adjustment for distractor information and the stage(s) of processing affected. To assess the processing of distractors during sensory-perceptual phases we applied EEG recording in a stimulus identification task, involving successive distractor-target presentation, and manipulated the overall distractor utility. Behavioral measures replicated previously found utility modulations of distractor interference. Crucially, distractor-evoked visual potentials (i.e., posterior N1) were more pronounced in high-utility than low-utility conditions. This effect generalized to distractors unrelated to the utility manipulation, providing evidence for item-unspecific adjustment of early distractor processing to the experienced utility of distractor information. Copyright © 2014 the authors 0270-6474/14/3416720-06$15.00/0.

Development of a multi-criteria evaluation system to assess growing pig welfare.

PubMed

Martín, P; Traulsen, I; Buxadé, C; Krieter, J

2017-03-01

The aim of this paper was to present an alternative multi-criteria evaluation model to assess animal welfare on farms based on the Welfare Quality® (WQ) project, using an example of welfare assessment of growing pigs. The WQ assessment protocol follows a three-step aggregation process. Measures are aggregated into criteria, criteria into principles and principles into an overall assessment. This study focussed on the first step of the aggregation. Multi-attribute utility theory (MAUT) was used to produce a value of welfare for each criterion. The utility functions and the aggregation function were constructed in two separated steps. The Measuring Attractiveness by a Categorical Based Evaluation Technique (MACBETH) method was used for utility function determination and the Choquet Integral (CI) was used as an aggregation operator. The WQ decision-makers' preferences were fitted in order to construct the utility functions and to determine the CI parameters. The methods were tested with generated data sets for farms of growing pigs. Using the MAUT, similar results were obtained to the ones obtained applying the WQ protocol aggregation methods. It can be concluded that due to the use of an interactive approach such as MACBETH, this alternative methodology is more transparent and more flexible than the methodology proposed by WQ, which allows the possibility to modify the model according, for instance, to new scientific knowledge.

Utility of pre-procurement bedside liver biopsy in the deceased extended-criteria liver donor.

PubMed

Mangus, Richard S; Borup, Tim C; Popa, Sam; Saxena, Romil; Cummings, Oscar; Tector, A Joseph

2014-12-01

The Indiana Organ Procurement Organization (IOPO) utilizes preoperative bedside liver biopsies in certain extended-criteria donors (ECDs), obtained by the on-site coordinator, to determine the utility of pursuing donation. This study reports the clinical and financial outcomes for this management strategy. All bedside liver biopsies obtained in ECDs over a five-yr period were reviewed. Study variables included the following: indication for biopsy, biopsy results, taking the case to the operating room, transplantation of the donor liver, and graft survival. All biopsies were processed at a single university center. There were 110 donors biopsied. Primary indications included the following: old age (29%), extensive/current alcohol abuse (26%), hepatitis C-positive serology (21%), obesity (25%), and severely elevated liver function enzymes (18%). Biopsy results demonstrated a potentially transplantable liver in 73 cases (66%), all of whom were taken to the OR (while 37 ruled out for donation based upon liver biopsy [34%]). Of all biopsied livers, 49 ultimately were transplanted (45%). Intra-operative decisions included the following: transplant 51/73 (70%), surgeon decision to exclude 20/73 (27%), nonuse due to finding of malignancy two (3%). Bedside liver biopsy may be a valuable tool to determine the utility in pursuing donation in ECDs, particularly with liver-only donors. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Exploring the Utilization of Low-Pressure, Piston-Cylinder Experiments to Determine the Bulk Compositions of Finite, Precious Materials

NASA Technical Reports Server (NTRS)

Vander Kaaden, K. E.; McCubbin, F. M.; Harrington, A. D.

2017-01-01

Determining the bulk composition of precious materials with a finite mass (e.g., meteorite samples) is extremely important in the fields of Earth and Planetary Science. From meteorite studies we are able to place constraints on large scale planetary processes like global differentiation and subsequent volcanism, as well as smaller scale processes like crystallization in a magma chamber or sedimentary compaction at the surface. However, with meteorite samples in particular, far too often we are limited by how precious the sample is as well as its limited mass. In this study, we have utilized aliquots of samples previously studied for toxicological hazards, including both the fresh samples (lunar mare basalt NWA 4734, lunar regolith breccia NWA 7611, martian basalt Tissint, martian regolith breccia NWA 7034, a vestian basalt Berthoud, a vestian regolith breccia NWA 2060, and a terrestrial mid-ocean ridge basalt (MORB)), and those that underwent iron leaching (Tissint, NWA 7034, NWA 4734, MORB). With these small masses of material, we performed low pressure (approx. 0.75 GPa), high temperature (greater than 1600 degrees Celsius) melting experiments. Each sample was analyzed using a JEOL 8530F electron microprobe to determine the bulk composition of the materials that were previously examined. When available, the results of our microprobe data were compared with bulk rock compositions in the literature. The results of this study show that with this technique, only approx. 50 mg of sample is required to accurately determine the bulk composition of the materials of interest.

Portugal's special education law: implementing the International Classification of Functioning, Disability and Health in policy and practice.

PubMed

Sanches-Ferreira, Manuela; Simeonsson, Rune J; Silveira-Maia, Mónica; Alves, Sílvia; Tavares, Ana; Pinheiro, Sara

2013-05-01

The International Classification of Functioning, Disability and Health (ICF) was introduced in Portuguese education law as the compulsory system to guide eligibility policy and practice in special education. This paper describes the implementation of the ICF and its utility in the assessment process and eligibility determination of students for special education. A study to evaluate the utility of the ICF was commissioned by the Portuguese Ministry of Education and carried out by an external evaluation team. A document analysis was made of the assessment and eligibility processes of 237 students, selected from a nationally representative sample. The results provided support for the use of the ICF in student assessment and in the multidimensional approach of generating student functioning profiles as the basis for determining eligibility. The use of the ICF contributed to the differentiation of eligible and non eligible students based on their functioning profiles. The findings demonstrate the applicability of the ICF framework and classification system for determining eligibility for special education services on the basis of student functioning rather than medical or psychological diagnose. The use of the International Classification of Functioning, Disability and Health (ICF) framework in special education policy is as follows: • The functional perspective of the ICF offers a more comprehensive, holistic assessment of student needs than medical diagnoses. • ICF-based assessment of the nature and severity of functioning can serve as the basis for determining eligibility for special education and habilitation. • Profiles of functioning can support decision making in designing appropriate educational interventions for students.

Modeling of ultrasonic processes utilizing a generic software framework

NASA Astrophysics Data System (ADS)

Bruns, P.; Twiefel, J.; Wallaschek, J.

2017-06-01

Modeling of ultrasonic processes is typically characterized by a high degree of complexity. Different domains and size scales must be regarded, so that it is rather difficult to build up a single detailed overall model. Developing partial models is a common approach to overcome this difficulty. In this paper a generic but simple software framework is presented which allows to coupe arbitrary partial models by slave modules with well-defined interfaces and a master module for coordination. Two examples are given to present the developed framework. The first one is the parameterization of a load model for ultrasonically-induced cavitation. The piezoelectric oscillator, its mounting, and the process load are described individually by partial models. These partial models then are coupled using the framework. The load model is composed of spring-damper-elements which are parameterized by experimental results. In the second example, the ideal mounting position for an oscillator utilized in ultrasonic assisted machining of stone is determined. Partial models for the ultrasonic oscillator, its mounting, the simplified contact process, and the workpiece’s material characteristics are presented. For both applications input and output variables are defined to meet the requirements of the framework’s interface.

Alternative bioenergy through the utilization of Kappaphycus alvarezii waste as a substitution of substrate for biogas products

NASA Astrophysics Data System (ADS)

Yulita, R.; Agustono; Pujiastuti, D. Y.; Alamsjah, M. A.

2018-04-01

Biogas is one of the renewable energy resources which are able to be developed by providing some sufficient renewable substances and manufactured from the fermentation process of organic substances metabolized by anaerobic bacteria. In this research, Kappaphycus alvarezii seaweed waste from carrageenan processing and contents of rumen were used. This research aims to comprehend the carrageenan processing waste of macroalga K. alvarezii can be used as alternative source generating biogas. The research method is P0 (100 % of the contents of rumen), P1 (75 % of the contents of rumen and 25 % of seaweed waste), P2 (50 % of the contents of rumen and 50 % of seaweed waste), and P3 (25 % of the contents of rumen and 75 % of seaweed waste), and P4 (100 % of seaweed waste). The result showed that according to the quality determination of biogas based on SNI (Indonesia National Standard) 8019:2014, the K. alvarezii seaweed waste from carrageenan processing can be utilized as the alternative source of manufacturing biogas and got the methane gas resulted from the comparison method is P2 (50 % of the contents of rumen and 50 % of seaweed waste), with value of 58.61 %.

Protection of children's rights to self-determination in research.

PubMed

Sterling, Cheryl M; Walco, Gary A

2003-01-01

Federal guidelines require that informed consent be obtained from participants when they are enrolled in a research study. When conducting research with children, the guidelines utilize the term permission to describe parents' agreement to enroll their children in a study. The basic components of consent and permission are well described and identical, with the exception of the person for whom the decision to participate is being made (i.e., oneself as opposed to one's child). Beyond permission, when enrolling minor participants in research, affirmative agreement to participate in research or assent must be obtained from the child participants themselves. The concept of children's assent to research, however, is poorly defined, resulting in inconsistency in its pursuit and consequently, in its utility. The interface between cognitive development, emotional, and social development must be examined as its pertains to this special situation of decision making. For this process to meaningfully protect minors, the assent process must be clarified, decisions regarding parental veto power must be more convincingly justified, and researchers must be better educated and held accountable for the valid execution of this process. Strategies for implementing the assent process more effectively are presented.

Investigation into the use of microwave sensors to monitor particulate manufacturing processes

NASA Astrophysics Data System (ADS)

Austin, John Samuel, III

Knowledge of a material's properties in-line during manufacture is of critical importance to many industries, including the pharmaceutical industry, and can be used for either process or quality control. Different microwave sensor configurations were tested to determine both the moisture content and the bulk density in pharmaceutical powders during processing on-line. Although these parameters can significantly affect a material's flowability, compressibility, and cohesivity, in the presence of blends, the picture is incomplete. Due to the ease with which particulate blends tend to segregate, blend uniformity and chemical composition are two critical parameters in nearly all solids manufacturing industries. The prevailing wisdom has been that microwave sensors are not capable of or sensitive enough to measure the relative concentrations of components in a blend. Consequently, it is common to turn to near infrared sensing to determine material composition on-line. In this study, a novel microwave sensor was designed and utilized to determine, separately, the concentrations of different components in a blend of pharmaceutical powders. This custom microwave sensor was shown to have comparable accuracy to the state-of-the-art for both chemical composition and moisture content determination.

Fly Ash: From Cradle to Grave

USGS Publications Warehouse

Ellis, Margaret S.; Affolter, Ronald H.

2007-01-01

The Energy Resources Program of the U.S. Geological Survey promotes and supports coal research to improve the understanding of the coal endowment of the United States. This results in geologically based, non-biased energy information products for policy and decision makers, land and resource managers, other federal and state agencies, the domestic energy industry, foreign governments, nongovernmental groups, academia, and other scientists. A more integrated approach to our coal quality work involves what we call a 'cradle to grave' approach. These types of studies focus not on just one aspect of the coal but rather on how or where different quality parameters form and (or) occur and what happens to them through the mining, production, transport, utilization and waste disposal process. An extensive suite of coal quality analyses, mineralogical, petrology, and leaching investigations are determined on samples taken from the different phases of the coal utilization process. This report consists of a tutorial that was given on June 10, 2007 at the 32nd International Technical Conference on Coal Utilization & Fuel Systems, The Power of Coal, Clearwater Coal Conference in Clearwater, Florida, USA. This tutorial covers how these studies are conducted and the importance of providing improved, comprehensive, science-based data sets for policy and decision makers.

Enhancement of n-butanol production by in situ butanol removal using permeating-heating-gas stripping in acetone-butanol-ethanol fermentation.

PubMed

Chen, Yong; Ren, Hengfei; Liu, Dong; Zhao, Ting; Shi, Xinchi; Cheng, Hao; Zhao, Nan; Li, Zhenjian; Li, Bingbing; Niu, Huanqing; Zhuang, Wei; Xie, Jingjing; Chen, Xiaochun; Wu, Jinglan; Ying, Hanjie

2014-07-01

Butanol recovery from acetone-butanol-ethanol (ABE) fed-batch fermentation using permeating-heating-gas was determined in this study. Fermentation was performed with Clostridium acetobutylicum B3 in a fibrous bed bioreactor and permeating-heating-gas stripping was used to eliminate substrate and product inhibition, which normally restrict ABE production and sugar utilization to below 20 g/L and 60 g/L, respectively. In batch fermentation (without permeating-heating-gas stripping), C. acetobutylicum B3 utilized 60 g/L glucose and produced 19.9 g/L ABE and 12 g/L butanol, while in the integrated process 290 g/L glucose was utilized and 106.27 g/L ABE and 66.09 g/L butanol were produced. The intermittent gas stripping process generated a highly concentrated condensate containing approximately 15% (w/v) butanol, 4% (w/v) acetone, a small amount of ethanol (<1%), and almost no acids, resulting in a highly concentrated butanol solution [∼ 70% (w/v)] after phase separation. Butanol removal by permeating-heating-gas stripping has potential for commercial ABE production. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Development of Processing Techniques for Advanced Thermal Protection Materials

NASA Technical Reports Server (NTRS)

Selvaduray, Guna; Cox, Michael; Srinivasan, Vijayakumar

1997-01-01

Thermal Protection Materials Branch (TPMB) has been involved in various research programs to improve the properties and structural integrity of the existing aerospace high temperature materials. Specimens from various research programs were brought into the analytical laboratory for the purpose of obtaining and refining the material characterization. The analytical laboratory in TPMB has many different instruments which were utilized to determine the physical and chemical characteristics of materials. Some of the instruments that were utilized by the SJSU students are: Scanning Electron Microscopy (SEM), Energy Dispersive X-ray analysis (EDX), X-ray Diffraction Spectrometer (XRD), Fourier Transform-Infrared Spectroscopy (FTIR), Ultra Violet Spectroscopy/Visible Spectroscopy (UV/VIS), Particle Size Analyzer (PSA), and Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). The above mentioned analytical instruments were utilized in the material characterization process of the specimens from research programs such as: aerogel ceramics (I) and (II), X-33 Blankets, ARC-Jet specimens, QUICFIX specimens and gas permeability of lightweight ceramic ablators. In addition to analytical instruments in the analytical laboratory at TPMB, there are several on-going experiments. One particular experiment allows the measurement of permeability of ceramic ablators. From these measurements, physical characteristics of the ceramic ablators can be derived.

αCP Poly(C) Binding Proteins Act as Global Regulators of Alternative Polyadenylation

PubMed Central

Ji, Xinjun; Wan, Ji; Vishnu, Melanie

2013-01-01

We have previously demonstrated that the KH-domain protein αCP binds to a 3′ untranslated region (3′UTR) C-rich motif of the nascent human alpha-globin (hα-globin) transcript and enhances the efficiency of 3′ processing. Here we assess the genome-wide impact of αCP RNA-protein (RNP) complexes on 3′ processing with a specific focus on its role in alternative polyadenylation (APA) site utilization. The major isoforms of αCP were acutely depleted from a human hematopoietic cell line, and the impact on mRNA representation and poly(A) site utilization was determined by direct RNA sequencing (DRS). Bioinformatic analysis revealed 357 significant alterations in poly(A) site utilization that could be specifically linked to the αCP depletion. These APA events correlated strongly with the presence of C-rich sequences in close proximity to the impacted poly(A) addition sites. The most significant linkage was the presence of a C-rich motif within a window 30 to 40 bases 5′ to poly(A) signals (AAUAAA) that were repressed upon αCP depletion. This linkage is consistent with a general role for αCPs as enhancers of 3′ processing. These findings predict a role for αCPs in posttranscriptional control pathways that can alter the coding potential and/or levels of expression of subsets of mRNAs in the mammalian transcriptome. PMID:23629627

Technologies for Upgrading Light Water Reactor Outlet Temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel S. Wendt; Piyush Sabharwall; Vivek Utgikar

Nuclear energy could potentially be utilized in hybrid energy systems to produce synthetic fuels and feedstocks from indigenous carbon sources such as coal and biomass. First generation nuclear hybrid energy system (NHES) technology will most likely be based on conventional light water reactors (LWRs). However, these LWRs provide thermal energy at temperatures of approximately 300°C, while the desired temperatures for many chemical processes are much higher. In order to realize the benefits of nuclear hybrid energy systems with the current LWR reactor fleets, selection and development of a complimentary temperature upgrading technology is necessary. This paper provides an initial assessmentmore » of technologies that may be well suited toward LWR outlet temperature upgrading for powering elevated temperature industrial and chemical processes during periods of off-peak power demand. Chemical heat transformers (CHTs) are a technology with the potential to meet LWR temperature upgrading requirements for NHESs. CHTs utilize chemical heat of reaction to change the temperature at which selected heat sources supply or consume thermal energy. CHTs could directly utilize LWR heat output without intermediate mechanical or electrical power conversion operations and the associated thermodynamic losses. CHT thermal characteristics are determined by selection of the chemical working pair and operating conditions. This paper discusses the chemical working pairs applicable to LWR outlet temperature upgrading and the CHT operating conditions required for providing process heat in NHES applications.« less

System and method of designing a load bearing layer of an inflatable vessel

NASA Technical Reports Server (NTRS)

Spexarth, Gary R. (Inventor)

2007-01-01

A computer-implemented method is provided for designing a restraint layer of an inflatable vessel. The restraint layer is inflatable from an initial uninflated configuration to an inflated configuration and is constructed from a plurality of interfacing longitudinal straps and hoop straps. The method involves providing computer processing means (e.g., to receive user inputs, perform calculations, and output results) and utilizing this computer processing means to implement a plurality of subsequent design steps. The computer processing means is utilized to input the load requirements of the inflated restraint layer and to specify an inflated configuration of the restraint layer. This includes specifying a desired design gap between pairs of adjacent longitudinal or hoop straps, whereby the adjacent straps interface with a plurality of transversely extending hoop or longitudinal straps at a plurality of intersections. Furthermore, an initial uninflated configuration of the restraint layer that is inflatable to achieve the specified inflated configuration is determined. This includes calculating a manufacturing gap between pairs of adjacent longitudinal or hoop straps that correspond to the specified desired gap in the inflated configuration of the restraint layer.

Perceived ownership impacts reward evaluation within medial-frontal cortex.

PubMed

Krigolson, Olave E; Hassall, Cameron D; Balcom, Lynsey; Turk, David

2013-06-01

Ownership is a powerful construct. Indeed, in a series of recent studies, perceived ownership has been shown to increase attentional capacity, facilitate a memorial advantage, and elicit positive attitudes. Here, we sought to determine whether self-relevance would bias reward evaluation systems within the brain. To accomplish this, we had participants complete a simple gambling task during which they could "win" or "lose" prizes for themselves or for someone else, while electroencephalographic data were recorded. Our results indicated that the amplitude of the feedback error-related negativity, a component of the event-related brain potential sensitive to reward evaluation, was diminished when participants were not gambling for themselves. Furthermore, our data suggest that the ownership cues that indicated who would win or lose a given gamble either were processed as a potential for an increase in utility (i.e., gain: self-gambles) or were processed in a nonutilitarian manner (other-gambles). Importantly, our results suggest that the medial-frontal reward system is sensitive to perceived ownership, to the extent that it may not process changes in utility when they are not directly relevant to self.

An Application of Specific Sensors For The Monitoring of NaCl in Soft Cheeses

NASA Astrophysics Data System (ADS)

Lvova, Larisa; Mielle, Patrick; Salles, Christian; Denis, Sylvain; Vergoignan, Catherine; Barra, Aurélien; Di Natale, Corrado; Paolesse, Roberto; Temple-Boyer, Pierre; Feron, Gilles

2011-09-01

The commercial sensors and prototype ISEs array (Ion Selective Electrodes array) were utilized for NaCl concentration measurements in soft cheeses, in particular in vitro gut process and in commercial Italian mozzarella cheeses. The values obtained from the sensors were compared with HPLC analysis. The results showed the feasibility of the ISE array application to monitor NaCl in soft cheese during the breakdown in the digester. The best results were obtained with the use of ISEs array combining, in particular, Cl- and Na+ detections. The salinity of commercial mozzarella cheese samples and the originally utilized milk type (cow or buffalo) were also satisfactory determined with the developed ISE array.

Handbook of evaluation of utility DSM programs. [Demand-Side Management (DSM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirst, E.; Reed, J.; Bronfman, B.

Program evaluation has become a central issue in the world of utility integrated resource planning. The DSM programs that utilities were operating to meet federal requirements or to improve customer relations are now becoming big business. DSM is being considered an important resource in a utility's portfolio of options. In the last five years, the amount of money that utilities have invested in DSM has grown exponentially in most regulatory jurisdictions. Market analysts are now talking about DSM being a $30 billion industry by the end of the decade. If the large volume of DSM-program investments was not enough tomore » highlight the importance of evaluation, then the introduction of regulatory incentives has really focused the spotlight. This handbook was developed through a process that involved many of those people who represent the diverse constituencies of DSM-program evaluation. We have come to recognize the many technical disciplines that must be employed to evaluate DSM programs. An analysis might start out based on the principles of utility load research to find out what happened, but a combination of engineering and statistical methods must be used to triangulate'' an estimate of what would have happened without the program. The difference, of course, is that elusive but prized result of evaluation: what happened as the direct result of the DSM program. Technical performance of DSM measures is not the sole determinant of the answer, either. We also recognize the importance of such behavioral attributes of DSM as persistence and free ridership. Finally, DSM evaluation is meaningless without attention to planning an approach, communicating results to relevant decision-makers, and focusing as much on the process as the impacts of the program. These topics are all covered in this handbook.« less

Assessing the utility of cancer-registry-processed cause of death in calculating cancer-specific survival.

PubMed

Hu, Chung-Yuan; Xing, Yan; Cormier, Janice N; Chang, George J

2013-05-15

Cancer registries use algorithms to process cause of death (COD) data from death certificates, but uncertainties remain regarding the accuracy and utility of those data in calculating cancer-specific survival (CSS). Because it is impractical to reconfirm the COD through meticulous review of the primary medical records, the observed cancer deaths could be compared with the number of attributed deaths, as estimated by using a relative survival (RS) approach, to determine utility in CSS estimation. Six major cancer types were evaluated using Surveillance, Epidemiology, and End Results (SEER) data (1988-1999 cohort). The COD utility was quantified by using the observed-to-expected ratio (O/E ratio) approach, which was calculated as the SEER-documented observed number of cancer-specific deaths divided by the number of expected deaths attributed to the malignancies as estimated using a RS approach. Favorable utility would have an O/E ratio close to 1. In total, 338,445 patients were identified; and their O/E ratios were 0.97, 0.98, 0.90, 1.07, 1.02, and 0.92 for breast, colorectal, lung, melanoma, prostate, and pancreas cancer, respectively. O/E ratios varied slightly with patients' age, race, and tumor stage, but not by sex. CSS for patients with lung cancer appeared to be overestimated considerably. Patients with multiple cancer diagnoses had poor O/E ratios compared with those who had only 1 cancer. The utility of COD in calculating CSS depended variously on the risk of cancer-related mortality and nontumor factors. However, the impact of this variation on CSS generally was small. The current results indicated that the COD assigned by cancer registries has acceptable validity, and CSS is considered an acceptable surrogate for RS in most circumstances. Copyright © 2013 American Cancer Society.

Improved Anomaly Detection using Integrated Supervised and Unsupervised Processing

NASA Astrophysics Data System (ADS)

Hunt, B.; Sheppard, D. G.; Wetterer, C. J.

There are two broad technologies of signal processing applicable to space object feature identification using nonresolved imagery: supervised processing analyzes a large set of data for common characteristics that can be then used to identify, transform, and extract information from new data taken of the same given class (e.g. support vector machine); unsupervised processing utilizes detailed physics-based models that generate comparison data that can then be used to estimate parameters presumed to be governed by the same models (e.g. estimation filters). Both processes have been used in non-resolved space object identification and yield similar results yet arrived at using vastly different processes. The goal of integrating the results of the two is to seek to achieve an even greater performance by building on the process diversity. Specifically, both supervised processing and unsupervised processing will jointly operate on the analysis of brightness (radiometric flux intensity) measurements reflected by space objects and observed by a ground station to determine whether a particular day conforms to a nominal operating mode (as determined from a training set) or exhibits anomalous behavior where a particular parameter (e.g. attitude, solar panel articulation angle) has changed in some way. It is demonstrated in a variety of different scenarios that the integrated process achieves a greater performance than each of the separate processes alone.

Mission informed needed information: discoverable, available sensing sources (MINI-DASS): the operators and process flows the magic rabbits must negotiate

NASA Astrophysics Data System (ADS)

Kolodny, Michael A.

2017-05-01

Today's battlefield space is extremely complex, dealing with an enemy that is neither well-defined nor well-understood. Adversaries are comprised of widely-distributed, loosely-networked groups engaging in nefarious activities. Situational understanding is needed by decision makers; understanding of adversarial capabilities and intent is essential. Information needed at any time is dependent on the mission/task at hand. Information sources potentially providing mission-relevant information are disparate and numerous; they include sensors, social networks, fusion engines, internet, etc. Management of these multi-dimensional informational sources is critical. This paper will present a new approach being undertaken to answer the challenge of enhancing battlefield understanding by optimizing the utilization of available informational sources (means) to required missions/tasks as well as determining the "goodness'" of the information acquired in meeting the capabilities needed. Requirements are usually expressed in terms of a presumed technology solution (e.g., imagery). A metaphor of the "magic rabbits" was conceived to remove presumed technology solutions from requirements by claiming the "required" technology is obsolete. Instead, intelligent "magic rabbits" are used to provide needed information. The question then becomes: "WHAT INFORMATION DO YOU NEED THE RABBITS TO PROVIDE YOU?" This paper will describe a new approach called Mission-Informed Needed Information - Discoverable, Available Sensing Sources (MINI-DASS) that designs a process that builds information acquisition missions and determines what the "magic rabbits" need to provide in a manner that is machine understandable. Also described is the Missions and Means Framework (MMF) model used, the process flow utilized, the approach to developing an ontology of information source means and the approach for determining the value of the information acquired.

Process property studies of melt blown thermoplastic polyurethane polymers

NASA Astrophysics Data System (ADS)

Lee, Youn Eung

The primary goal of this research was to determine optimum processing conditions to produce commercially acceptable melt blown (MB) thermoplastic polyurethane (TPU) webs. The 6-inch MB line and the 20-inch wide Accurate Products MB pilot line at the Textiles and Nonwovens Development Center (TANDEC), The University of Tennessee, Knoxville, were utilized for this study. The MB TPU trials were performed in four different phases: Phase 1 focused on the envelope of the MB operating conditions for different TPU polymers; Phase 2 focused on the production of commercially acceptable MB TPU webs; Phase 3 focused on the optimization of the processing conditions of MB TPU webs, and the determination of the significant relationships between processing parameters and web properties utilizing statistical analyses; Based on the first three phases, a more extensive study of fiber and web formation in the MB TPU process was made and a multi liner regression model for the MB TPU process versus properties was also developed in Phase 4. In conclusion, the basic MB process was fundamentally valid for the MB TPU process; however, the MB process was more complicated for TPU than PP, because web structures and properties of MB TPUs are very sensitive to MB process conditions: Furthermore, different TPU grades responded very differently to MB processing and exhibited different web structure and properties. In Phase 3 and Phase 4, small fiber diameters of less than 5mum were produced from TPU237, TPU245 and TPU280 pellets, and the mechanical strengths of MB TPU webs including the tensile strength, tear strength, abrasion resistance and tensile elongation were notably good. In addition, the statistical model showed useful interaction regarding trends for processing parameters versus properties of MB TPU webs. Die and air temperature showed multicollinearity problems and fiber diameter was notably affected by air flow rate, throughput and die/air temperature. It was also shown that most of the MB TPU web properties including mechanical strength, air permeability and fiber diameters were affected by air velocity and die temperature.

A Systematic Review of Interventions on Patients' Social and Economic Needs.

PubMed

Gottlieb, Laura M; Wing, Holly; Adler, Nancy E

2017-11-01

Healthcare systems are experimenting increasingly with interventions to address patients' social and economic needs. This systematic review examines how often and how rigorously interventions bridging social and medical care have been evaluated. The review included literature from PubMed published between January 2000 and February 2017. Additional studies were identified by reference searches and consulting local experts. Included studies were based in the U.S.; addressed at least one social or economic determinant of health (e.g., housing, employment, food insecurity); and were integrated within the medical care delivery system. Data from included studies were abstracted in June 2015 (studies published January 2000-December 2014) and in March 2017 (studies published January 2015-February 2017). Screening of 4,995 articles identified 67 studies of 37 programs addressing social needs. Interventions targeted a broad range of social needs and populations. Forty studies involved non-experimental designs. There was wide heterogeneity in outcome measures selected. More studies reported findings associated with process (69%) or social or economic determinants of health (48%) outcomes than health (30%) or healthcare utilization or cost (27%) outcomes. Studies reporting health, utilization, or cost outcomes reported mixed results. Healthcare systems increasingly incorporate programs to address patients' social and economic needs in the context of care. But evaluations of these programs to date focus primarily on process and social outcomes and are often limited by poor study quality. Higher-quality studies that include common health and healthcare utilization outcomes would advance effectiveness research in this rapidly expanding field. Copyright © 2017 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Factors influencing dental utilization by U.S. military recruits.

PubMed

Chisick, M C; Poindexter, F R; York, A K

1996-12-01

This study identifies factors that influence dental utilization by U.S. military recruits prior to entering military service. Data were collected between February and June 1994 at one recruit in-processing site per service using self-administered questionnaires. A prestratified, systematic, random sample of 2,711 Army, Air Force, Navy, and Marine recruits was drawn. Women and minorities were oversampled. Using logistic regression to determine what factors contribute to the likelihood of recruits having seen a dentist over the past year reveals that the likelihood is greater for females, singles, Air Force personnel, Native Americans, and the better educated; the likelihood is less for recruits who are black, above 19 years old, from the Midwest, Southwest, or Pacific regions of the U.S., and who perceive a need for dental care. Education is the strongest predictor of dental utilization prior to entering military service.

Determining Component Probability using Problem Report Data for Ground Systems used in Manned Space Flight

NASA Technical Reports Server (NTRS)

Monaghan, Mark W.; Gillespie, Amanda M.

2013-01-01

During the shuttle era NASA utilized a failure reporting system called the Problem Reporting and Corrective Action (PRACA) it purpose was to identify and track system non-conformance. The PRACA system over the years evolved from a relatively nominal way to identify system problems to a very complex tracking and report generating data base. The PRACA system became the primary method to categorize any and all anomalies from corrosion to catastrophic failure. The systems documented in the PRACA system range from flight hardware to ground or facility support equipment. While the PRACA system is complex, it does possess all the failure modes, times of occurrence, length of system delay, parts repaired or replaced, and corrective action performed. The difficulty is mining the data then to utilize that data in order to estimate component, Line Replaceable Unit (LRU), and system reliability analysis metrics. In this paper, we identify a methodology to categorize qualitative data from the ground system PRACA data base for common ground or facility support equipment. Then utilizing a heuristic developed for review of the PRACA data determine what reports identify a credible failure. These data are the used to determine inter-arrival times to perform an estimation of a metric for repairable component-or LRU reliability. This analysis is used to determine failure modes of the equipment, determine the probability of the component failure mode, and support various quantitative differing techniques for performing repairable system analysis. The result is that an effective and concise estimate of components used in manned space flight operations. The advantage is the components or LRU's are evaluated in the same environment and condition that occurs during the launch process.

F-Tank Farm Performance Assessment Updates through the Special Analysis Process at Savannah River Site - 12169

DOE Office of Scientific and Technical Information (OSTI.GOV)

Layton, Mark H.

2012-07-01

The F-Area Tank Farm (FTF) is owned by the U.S. Department of Energy and operated by Savannah River Remediation, LLC (SRR), Liquid Waste Operations contractor at DOE's Savannah River Site (SRS). The FTF is in the north-central portion of the SRS and occupies approximately 22 acres within F-Area. The FTF is an active radioactive waste storage facility consisting of 22 carbon steel waste tanks and ancillary equipment such as transfer lines, evaporators and pump tanks. An FTF Performance Assessment (PA) was prepared to support the eventual closure of the FTF underground radioactive waste tanks and ancillary equipment. The PA providesmore » the technical basis and results to be used in subsequent documents to demonstrate compliance with the pertinent requirements identified below for final closure of FTF. The FTank Farm is subject to a state industrial waste water permit and Federal Facility Agreement. Closure documentation will include an F-Tank Farm Closure Plan and tank-specific closure modules utilizing information from the performance assessment. For this reason, the State of South Carolina and the Environmental Protection Agency must be involved in the performance assessment review process. The residual material remaining after tank cleaning is also subject to reclassification prior to closure via a waste determination pursuant to Section 3116 of the Ronald W. Reagan National Defense Authorization Act of Fiscal Year 2005. The projected waste tank inventories in the FTF PA provide reasonably bounding FTF inventory projections while taking into account uncertainties in the effectiveness of future tank cleaning technologies. As waste is removed from the FTF waste tanks, the residual contaminants will be sampled and the remaining residual inventory is characterized. In this manner, tank specific data for the tank inventories at closure will be available to supplement the waste tank inventory projections currently used in the FTF PA. For FTF, the new tank specific data will be evaluated through the Special Analysis process. The FTF Special Analyses process will be utilized to evaluate information regarding the final residual waste that will be grouted in place in the FTF Tanks and assess the potential impact the new inventory information has on the FTF PA assumptions and results. The Special Analysis can then be used to inform decisions regarding FTF tank closure documents. The purpose of this paper is to discuss the Special Analysis process and share insights gained while implementing this process. An example of an area of interest in the revision process is balancing continuous improvement versus configuration control of agreed upon methodologies. Other subjects to be covered include: 1) defining the scope of the revisions included in the Special Analysis, 2) determining which PA results should be addressed in the Special Analysis, and 3) deciding whether the Special Analysis should utilize more qualitative or quantitative assessments. For the SRS FTF, an FTF PA has been prepared to provide the technical basis and results to be used in subsequent documents to demonstrate compliance with the pertinent requirements for final closure of FTF. The FTF Special Analyses process will be utilized to evaluate the impact new information has on the FTF PA assumptions and results. The Special Analysis can then be used to inform decisions regarding FTF tank closure documents. In preparing SAs, it is crucial that the scope of the SA be well defined within the SA, since the specific scope will vary from SA to SA. Since the SAs are essentially addendums to the PA, the SA scope should utilize the PA as the baseline from which the SA scope is defined. The SA needs to focus on evaluating the change associated with the scope, and not let other changes interfere with the ability to perform that evaluation by masking the impact of the change. In preparing the SA, it is also important to let the scope determine whether the Special Analysis should utilize more qualitative or quantitative assessments and also which results from the PA should be addressed in the Special Analysis. These decisions can vary from SA and should not be predetermined. (author)« less

Modeling the Gas Nitriding Process of Low Alloy Steels

NASA Astrophysics Data System (ADS)

Yang, M.; Zimmerman, C.; Donahue, D.; Sisson, R. D.

2013-07-01

The effort to simulate the nitriding process has been ongoing for the last 20 years. Most of the work has been done to simulate the nitriding process of pure iron. In the present work a series of experiments have been done to understand the effects of the nitriding process parameters such as the nitriding potential, temperature, and time as well as surface condition on the gas nitriding process for the steels. The compound layer growth model has been developed to simulate the nitriding process of AISI 4140 steel. In this paper the fundamentals of the model are presented and discussed including the kinetics of compound layer growth and the determination of the nitrogen diffusivity in the diffusion zone. The excellent agreements have been achieved for both as-washed and pre-oxided nitrided AISI 4140 between the experimental data and simulation results. The nitrogen diffusivity in the diffusion zone is determined to be constant and only depends on the nitriding temperature, which is ~5 × 10-9 cm2/s at 548 °C. It proves the concept of utilizing the compound layer growth model in other steels. The nitriding process of various steels can thus be modeled and predicted in the future.

Analysis of Water Resource Utilization Potential for Jiangsu Coastal Area ' in Nantong City

NASA Astrophysics Data System (ADS)

Ren, Li; Liu, Jin-Tao; Ni, Jian-Jun

2015-04-01

Along with the advance of the growth of population and social economy, requirements for water quality and quantity in coastal areas is getting higher and higher, but due to the uneven distribution of rainfall years and water exploitation, use and management level, the influence of the shortage of water resources is increasingly prominent, seriously restricting the social and economic sustainable development in this region. Accordingly, water resource utilization potential in Jiangsu coastal region is vital for water security in the region. Taking Nantong City as the study area, the regional water resources development and utilization status were evaluated. In this paper, the meaning of water resources, water resources development and utilization, and water resources development and utilization of the three stages of concepts such as system were discussed. Then the development and utilization of regional water resource evaluation were carried out, and the significance of regional society, economy, resources and environment and its development status quo of water resources were exploited. According to conditions and area source, an evaluation index system for development and utilization of water resources of Nantong was built up. The index layer was composed of 16 indicators. In this study, analytic hierarchy process (AHP) was used to determine of weights of indicators at all levels in the index system. Multistage fuzzy comprehensive evaluation model was selected to evaluate the water resources development and utilization status of Nantong, and then water resource utilization potential of Nantong was analyzed.

Ion time-of-flight determinations of doubly to singly ionized mercury ion ratios from a mercury electron bombardment discharge

NASA Technical Reports Server (NTRS)

Sellen, J. M., Jr.; Kemp, R. F.; Hall, D. F.

1973-01-01

Doubly to singly charged mercury ion ratios in electron bombardment ion thruster exhaust beams have been determined as functions of bombardment discharge potential, thrust beam current, thrust beam radial position, acceleration-deceleration voltage ratio, and propellant utilization fraction. A mathematical model for two-step ionization processes has been derived, and calculated ion ratios are compared to observed ratios. Production of Hg(++) appears to result primarily from sequential ionization of Hg(+) in the discharge. Experimental and analytical results are presented, and design, construction, and operation features of an electrostatic deflection ion time-of-flight analyzer for the determination of the above-mentioned ratios are reviewed.

12 CFR 1320.12 - Advance notice of proposed determination.

Code of Federal Regulations, 2012 CFR

2012-01-01

... MARKET UTILITIES Consultations, Determinations and Hearings § 1320.12 Advance notice of proposed determination. (a) Notice of proposed determination and opportunity for hearing. Before making any final... provide the financial market utility with advance notice of the proposed determination, and proposed...

12 CFR 1320.12 - Advance notice of proposed determination.

Code of Federal Regulations, 2013 CFR

2013-01-01

... MARKET UTILITIES Consultations, Determinations and Hearings § 1320.12 Advance notice of proposed determination. (a) Notice of proposed determination and opportunity for hearing. Before making any final... provide the financial market utility with advance notice of the proposed determination, and proposed...

12 CFR 1320.12 - Advance notice of proposed determination.

Code of Federal Regulations, 2014 CFR

2014-01-01

... MARKET UTILITIES Consultations, Determinations and Hearings § 1320.12 Advance notice of proposed determination. (a) Notice of proposed determination and opportunity for hearing. Before making any final... provide the financial market utility with advance notice of the proposed determination, and proposed...

Technology and surgery. Dilemma of the gimmick, true advances, and cost effectiveness.

PubMed

Traverso, L W

1996-02-01

The key to evaluating a procedure in regard to a true advance versus a gimmick is to determine its value. This can be done only by physicians cognizant of a disease process. The value is determined by assessing a procedure's utilization, outcomes, and costs. Utilization allows early treatment and avoids neglected disease. Therefore, the appropriateness of the utilization can be determined only by an outcome study. An outcome study is another term for quality assessment. Outcomes deal with morbidity, mortality, and also the long- and short-term effects of the procedure on the disease. Overall, an increase of quality in a global perspective decreases the costs of the procedure to the health care community. Costs must remain secondary to outcomes. An attempt to decrease costs directly is a maneuver that, when applied by nonmedical individuals, will most likely decrease quality. When the quality can be maintained (as assessed only by a practitioner), then a decrease in global costs will increase value. The concept of increasing value by increasing quality without an attempt to decrease costs is a very important principle that the health care system must learn in our ever-challenging medical environment. Is a new procedure a gimmick or a true advance? The decision is made jointly by the stakeholders in our health care system--the patient, provider, payer, employer, and industry. If the procedure does not receive negative votes, then its adoption is almost assured. Comparing two procedures through these perspectives ultimately allows us to determine the potential for new procedures. A procedure not adopted through this method could be called a gimmick.

Determining sample size for tree utilization surveys

Treesearch

Stanley J. Zarnoch; James W. Bentley; Tony G. Johnson

2004-01-01

The U.S. Department of Agriculture Forest Service has conducted many studies to determine what proportion of the timber harvested in the South is actually utilized. This paper describes the statistical methods used to determine required sample sizes for estimating utilization ratios for a required level of precision. The data used are those for 515 hardwood and 1,557...

Elevated temperature crack growth

NASA Technical Reports Server (NTRS)

Malik, S. N.; Vanstone, R. H.; Kim, K. S.; Laflen, J. H.

1986-01-01

It is necessary to relate the processes that control crack growth in the immediate vicinity of the crack tip to parameters that can be calculated from remote quantities, such as forces, stresses, or displacements. The most likely parameters appear to be certain path-independent (PI) integrals, several of which have already been proposed for application to high temperature inelastic problems. The ability of currently available PI-integrals to correlate fatigue crack propagation under conditions that simulate the engine combustor liner environment was determined. The utility of advanced fracture mechanics measurements will also be evaluated and determined during the course of the program.

Seasonal variability of light availability and utilization in the Sargasso Sea

NASA Technical Reports Server (NTRS)

Siegel, David A.; Michaels, Anthony F.; Sorensen, Jens C.; O'Brein, Margaret C.; Hammer, Melodie A.

1995-01-01

A 2 year time series of optical, biogeochemical, and physical parameters, taken near the island of Bermuda, is used to evaluate the sources of temporal variability in light avaliability and utilization in the Sargasso Sea. Integrated assessments of light availability are made by examining the depth of constant percent incident photosynthetically available radiation (% PAR) isolumes. To first order, changes in the depth %PAR isolumes were caused by physical processes: deep convection mixing in the winter which led to the spring bloom and concurrent shallowing of %PAR depths and the occurrence of anomalous thermohaline water masses during the summer and fall seasons. Spectral light availability variations are assessed using determinations of diffuse attenuation coefficient spectra which illustrates a significant seasonal cycle in colored detrital particulate and/or dissolved materials that is unrelated to changes in chlorophyll pigment concentrations. Temporal variations in the photosynthetic light utilization index Psi are used to assess vertically intergrated light utilization variations. Values of Psi are highly variable and show no apparent seasonal pattern which indicates that Psi is not simply a 'biogeochemical constant.' Determinations of in situ primary production rates and daily mean PAR fluxes are used to diagnose the relative role of light limitation in determining vertically integrated rates of primary production integral PP. The mean depth of the light-saturated zone (the vertical region where the daily mean PAR flux was greater than or equal to the saturation irradiance) is only approximately 40 m, although more than one half of interal PP occurred within this zone. Production model results illustrate that accurate predictions of integral PP are dependent upon rates of light-saturated production rather than upon indices of light limitation. It seems unlikely that significant improvements in simple primary production models will come from the partitioning of the Earth's seas into biogeochemical provinces.

Quality of Information Approach to Improving Source Selection in Tactical Networks

DTIC Science & Technology

2017-02-01

consider the performance of this process based on metrics relating to quality of information: accuracy, timeliness, completeness and reliability. These...that are indicators of that the network is meeting these quality requirements. We study effective data rate, social distance, link integrity and the...utility of information as metrics within a multi-genre network to determine the quality of information of its available sources. This paper proposes a

Preliminary design of a redundant strapped down inertial navigation unit using two-degree-of-freedom tuned-gimbal gyroscopes

NASA Technical Reports Server (NTRS)

1976-01-01

This redundant strapdown INS preliminary design study demonstrates the practicality of a skewed sensor system configuration by means of: (1) devising a practical system mechanization utilizing proven strapdown instruments, (2) thoroughly analyzing the skewed sensor redundancy management concept to determine optimum geometry, data processing requirements, and realistic reliability estimates, and (3) implementing the redundant computers into a low-cost, maintainable configuration.

Spectroscopic Determination of the AC Voltammetric Response.

DTIC Science & Technology

1984-01-06

characterization of electrode processes. More recently, with the advent of linear sweep cyclic AC voltanmetry(12’ 13), it has been shown that AC methods...implemented with the same instrumentation ( 7 ) as previously used in MSRS and retains both the qualitative and quantitative utility of linear sweep ...voltammetric response (eg. peak width at balf-height, peak separation and cross-over potential in cyclic AC voltametry ) apply equally well to the SACRS

Validity and reliability of an application review process using dedicated reviewers in one stage of a multi-stage admissions model.

PubMed

Zeeman, Jacqueline M; McLaughlin, Jacqueline E; Cox, Wendy C

2017-11-01

With increased emphasis placed on non-academic skills in the workplace, a need exists to identify an admissions process that evaluates these skills. This study assessed the validity and reliability of an application review process involving three dedicated application reviewers in a multi-stage admissions model. A multi-stage admissions model was utilized during the 2014-2015 admissions cycle. After advancing through the academic review, each application was independently reviewed by two dedicated application reviewers utilizing a six-construct rubric (written communication, extracurricular and community service activities, leadership experience, pharmacy career appreciation, research experience, and resiliency). Rubric scores were extrapolated to a three-tier ranking to select candidates for on-site interviews. Kappa statistics were used to assess interrater reliability. A three-facet Many-Facet Rasch Model (MFRM) determined reviewer severity, candidate suitability, and rubric construct difficulty. The kappa statistic for candidates' tier rank score (n = 388 candidates) was 0.692 with a perfect agreement frequency of 84.3%. There was substantial interrater reliability between reviewers for the tier ranking (kappa: 0.654-0.710). Highest construct agreement occurred in written communication (kappa: 0.924-0.984). A three-facet MFRM analysis explained 36.9% of variance in the ratings, with 0.06% reflecting application reviewer scoring patterns (i.e., severity or leniency), 22.8% reflecting candidate suitability, and 14.1% reflecting construct difficulty. Utilization of dedicated application reviewers and a defined tiered rubric provided a valid and reliable method to effectively evaluate candidates during the application review process. These analyses provide insight into opportunities for improving the application review process among schools and colleges of pharmacy. Copyright © 2017 Elsevier Inc. All rights reserved.

Wash water recovery system

NASA Technical Reports Server (NTRS)

Deckman, G.; Rousseau, J. (Editor)

1973-01-01

The Wash Water Recovery System (WWRS) is intended for use in processing shower bath water onboard a spacecraft. The WWRS utilizes flash evaporation, vapor compression, and pyrolytic reaction to process the wash water to allow recovery of potable water. Wash water flashing and foaming characteristics, are evaluated physical properties, of concentrated wash water are determined, and a long term feasibility study on the system is performed. In addition, a computer analysis of the system and a detail design of a 10 lb/hr vortex-type water vapor compressor were completed. The computer analysis also sized remaining system components on the basis of the new vortex compressor design.

Development of a Fiber Laser Welding Capability for the W76, MC4702 Firing Set

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samayoa, Jose

2010-05-12

Development work to implement a new welding system for a Firing Set is presented. The new system is significant because it represents the first use of fiber laser welding technology at the KCP. The work used Six-Sigma tools for weld characterization and to define process performance. Determinations of workable weld parameters and comparison to existing equipment were completed. Replication of existing waveforms was done utilizing an Arbitrary Pulse Generator (APG), which was used to modulate the fiber laser’s exclusive continuous wave (CW) output. Fiber laser weld process capability for a Firing Set is demonstrated.

Support for the Delisting of Decontaminated Liquid Chemical Surety Materials as Listed Hazardous Waste from Specific Sources (STATE) MD02 in COMAR 10.51.02.16-1

DTIC Science & Technology

1988-11-01

results. On the contrary, the active decon moiety in both cases is the hydroxyl ion (0OH), and the agent being decontaminated reacts exactly the same...methods. A review of method3 utilized to determine the concentration of active material before and after the decontamination process. Included are the most...isolation of acid A, acid B will probably be excluded by the forces active in the crystallization process. Acid B will therefore be missed in the overall

Test rig and particulate deposit and cleaning evaluation processes using the same

DOEpatents

Schroder, Mark Stewart; Woodmansee, Donald Ernest; Beadie, Douglas Frank

2002-01-01

A rig and test program for determining the amount, if any, of contamination that will collect in the passages of a fluid flow system, such as a power plant fluid delivery system to equipment assemblies or sub-assemblies, and for establishing methods and processes for removing contamination therefrom. In the presently proposed embodiment, the rig and test programs are adapted in particular to utilize a high-pressure, high-volume water flush to remove contamination from substantially the entire fluid delivery system, both the quantity of contamination and as disposed or deposited within the system.

Computer Modeling of Direct Metal Laser Sintering

NASA Technical Reports Server (NTRS)

Cross, Matthew

2014-01-01

A computational approach to modeling direct metal laser sintering (DMLS) additive manufacturing process is presented. The primary application of the model is for determining the temperature history of parts fabricated using DMLS to evaluate residual stresses found in finished pieces and to assess manufacturing process strategies to reduce part slumping. The model utilizes MSC SINDA as a heat transfer solver with imbedded FORTRAN computer code to direct laser motion, apply laser heating as a boundary condition, and simulate the addition of metal powder layers during part fabrication. Model results are compared to available data collected during in situ DMLS part manufacture.

Materials processing threshold report. 1: Semiconductor crystals for infrared detectors

NASA Technical Reports Server (NTRS)

Sager, E. V.; Thompson, T. R.; Nagler, R. G.

1980-01-01

An extensive search was performed of the open literature pertaining to infrared detectors to determine what constitutes a good detector and in what way performance is limited by specific material properties. Interviews were conducted with a number of experts in the field to assess their perceptions of the state of the art and of the utility of zero-gravity processing. Based on this information base and on a review of NASA programs in crystal growth and infrared sensors, NASA program goals were reassessed and suggestions are presented as to possible joint and divergent efforts between NASA and DOD.

{bold {ital In situ}} measurements of texture and phase development in (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}{endash}Ag tapes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thurston, T.R.; Haldar, P.; Wang, Y.L.

Hard x-rays from a synchrotron source were utilized in diffraction experiments performed at elevated temperatures (up to {approximately}870{degree}C) on (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Bi-2223) tapes {ital completely} encased in silver. The general behavior of the phase and texture development under typical processing conditions was determined, and the effects that several variations in processing conditions had on the phase and texture development were examined. These results and their implications for improving processing conditions are discussed. {copyright} {ital 1997 Materials Research Society.}

The application of digital signal processing techniques to a teleoperator radar system

NASA Technical Reports Server (NTRS)

Pujol, A.

1982-01-01

A digital signal processing system was studied for the determination of the spectral frequency distribution of echo signals from a teleoperator radar system. The system consisted of a sample and hold circuit, an analog to digital converter, a digital filter, and a Fast Fourier Transform. The system is interfaced to a 16 bit microprocessor. The microprocessor is programmed to control the complete digital signal processing. The digital filtering and Fast Fourier Transform functions are implemented by a S2815 digital filter/utility peripheral chip and a S2814A Fast Fourier Transform chip. The S2815 initially simulates a low-pass Butterworth filter with later expansion to complete filter circuit (bandpass and highpass) synthesizing.

Comparison of performance on process- and product-oriented assessments of fundamental motor skills across childhood.

PubMed

Logan, Samuel W; Barnett, Lisa M; Goodway, Jacqueline D; Stodden, David F

2017-04-01

Process-oriented motor competence (MC) assessments evaluate how a movement is performed. Product-oriented assessments evaluate the outcome of a movement. Determining the concurrent validity of process and product assessments is important to address the predictive utility of motor competence for health. The current study aimed to: (1) compare process and product assessments of the standing long jump, hop and throw across age groups and (2) determine the capacity of process assessments to classify levels of MC. Participants included 170 children classified into three age groups: 4-5, 7-8 and 10-11 years old. Participants' skills were examined concurrently using three process assessments ((Test of Gross Motor Development-2nd edition [TGMD-2]), Get Skilled; Get Active, and developmental sequences) and one product measure (throw speed, jump and hop distance). Results indicate moderate to strong correlations between (1) process assessments across skills and age groups (r range = .37-70) and (2) process and product assessments across skills and age groups (r range = .26-.88). In general, sensitivity to detect advanced skill level is lowest for TGMD-2 and highest for developmental sequences for all three skills. The use of process and product assessments is suggested to comprehensively capture levels of MC in human movement.

Metagenomic analysis of the rhizosphere soil microbiome with respect to phytic acid utilization.

PubMed

Unno, Yusuke; Shinano, Takuro

2013-01-01

While phytic acid is a major form of organic phosphate in many soils, plant utilization of phytic acid is normally limited; however, culture trials of Lotus japonicus using experimental field soil that had been managed without phosphate fertilizer for over 90 years showed significant usage of phytic acid applied to soil for growth and flowering and differences in the degree of growth, even in the same culture pot. To understand the key metabolic processes involved in soil phytic acid utilization, we analyzed rhizosphere soil microbial communities using molecular ecological approaches. Although molecular fingerprint analysis revealed changes in the rhizosphere soil microbial communities from bulk soil microbial community, no clear relationship between the microbiome composition and flowering status that might be related to phytic acid utilization of L. japonicus could be determined. However, metagenomic analysis revealed changes in the relative abundance of the classes Bacteroidetes, Betaproteobacteria, Chlorobi, Dehalococcoidetes and Methanobacteria, which include strains that potentially promote plant growth and phytic acid utilization, and some gene clusters relating to phytic acid utilization, such as alkaline phosphatase and citrate synthase, with the phytic acid utilization status of the plant. This study highlights phylogenetic and metabolic features of the microbial community of the L. japonicus rhizosphere and provides a basic understanding of how rhizosphere microbial communities affect the phytic acid status in soil.

Assessing and Adapting Scientific Results for Space Weather Research to Operations (R2O)

NASA Astrophysics Data System (ADS)

Thompson, B. J.; Friedl, L.; Halford, A. J.; Mays, M. L.; Pulkkinen, A. A.; Singer, H. J.; Stehr, J. W.

2017-12-01

Why doesn't a solid scientific paper necessarily result in a tangible improvement in space weather capability? A well-known challenge in space weather forecasting is investing effort to turn the results of basic scientific research into operational knowledge. This process is commonly known as "Research to Operations," abbreviated R2O. There are several aspects of this process: 1) How relevant is the scientific result to a particular space weather process? 2) If fully utilized, how much will that result improve the reliability of the forecast for the associated process? 3) How much effort will this transition require? Is it already in a relatively usable form, or will it require a great deal of adaptation? 4) How much burden will be placed on forecasters? Is it "plug-and-play" or will it require effort to operate? 5) How can robust space weather forecasting identify challenges for new research? This presentation will cover several approaches that have potential utility in assessing scientific results for use in space weather research. The demonstration of utility is the first step, relating to the establishment of metrics to ensure that there will be a clear benefit to the end user. The presentation will then move to means of determining cost vs. benefit, (where cost involves the full effort required to transition the science to forecasting, and benefit concerns the improvement of forecast reliability), and conclude with a discussion of the role of end users and forecasters in driving further innovation via "O2R."

Measuring bioenergetics in T cells using a Seahorse Extracellular Flux Analyzer

PubMed Central

van der Windt, Gerritje J.W.; Chang, Chih-Hao; Pearce, Erika L.

2016-01-01

This unit contains several protocols to determine the energy utilization of T cells in real-time using a Seahorse Extracellular Flux Analyzer (www.seahorsebio.com). The advantages to using this machine over traditional metabolic assays include the simultaneous measurement of glycolysis and mitochondrial respiration, in real-time, on relatively small numbers of cells, without any radioactivity. The Basic Protocol describes a standard mitochondrial stress test on the XFe96, which yields information about oxidative phosphorylation and glycolysis, two energy-generating pathways. The alternate protocols provide examples of adaptations to the Basic Protocol, including adjustments for the use of the XFe24. A protocol for real-time bioenergetic responses to T cell activation allows for the analysis of immediate metabolic changes after T cell receptor stimulation. Specific substrate utilization can be determined by the use of differential assay media, or the injection of drugs that specifically affect certain metabolic processes. Accurate cell numbers, purity, and viability are critical to obtain reliable results. PMID:27038461

Measuring Bioenergetics in T Cells Using a Seahorse Extracellular Flux Analyzer.

PubMed

van der Windt, Gerritje J W; Chang, Chih-Hao; Pearce, Erika L

2016-04-01

This unit contains several protocols to determine the energy utilization of T cells in real-time using a Seahorse Extracellular Flux Analyzer (http://www.seahorsebio.com). The advantages to using this machine over traditional metabolic assays include the simultaneous measurement of glycolysis and mitochondrial respiration, in real-time, on relatively small numbers of cells, without any radioactivity. The Basic Protocol describes a standard mitochondrial stress test on the XF(e) 96, which yields information about oxidative phosphorylation and glycolysis, two energy-generating pathways. The alternate protocols provide examples of adaptations to the Basic Protocol, including adjustments for the use of the XF(e) 24. A protocol for real-time bioenergetic responses to T cell activation allows for the analysis of immediate metabolic changes after T cell receptor stimulation. Specific substrate utilization can be determined by the use of differential assay media, or the injection of drugs that specifically affect certain metabolic processes. Accurate cell numbers, purity, and viability are critical to obtain reliable results. Copyright © 2016 John Wiley & Sons, Inc.

A new method for recognizing quadric surfaces from range data and its application to telerobotics and automation, final phase

NASA Technical Reports Server (NTRS)

Mielke, Roland; Dcunha, Ivan; Alvertos, Nicolas

1994-01-01

In the final phase of the proposed research a complete top to down three dimensional object recognition scheme has been proposed. The various three dimensional objects included spheres, cones, cylinders, ellipsoids, paraboloids, and hyperboloids. Utilizing a newly developed blob determination technique, a given range scene with several non-cluttered quadric surfaces is segmented. Next, using the earlier (phase 1) developed alignment scheme, each of the segmented objects are then aligned in a desired coordinate system. For each of the quadric surfaces based upon their intersections with certain pre-determined planes, a set of distinct features (curves) are obtained. A database with entities such as the equations of the planes and angular bounds of these planes has been created for each of the quadric surfaces. Real range data of spheres, cones, cylinders, and parallelpipeds have been utilized for the recognition process. The developed algorithm gave excellent results for the real data as well as for several sets of simulated range data.

The usage of waste heat recovery units with improved heat engineering rates: theory and experimental research

NASA Astrophysics Data System (ADS)

Chebotarev, Victor; Koroleva, Alla; Pirozhnikova, Anastasia

2017-10-01

Use of recuperator in heat producing plants for utilization of natural gas combustion products allows to achieve the saving of gas fuel and also provides for environmental sanitation. Decrease of the volumes of natural gas combustion due to utilization of heat provides not only for reduction of harmful agents in the combustion products discharged into the atmosphere, but also creates conditions for increase of energy saving in heating processes of heat producing plants due to air overheating in the recuperator. Grapho-analytical method of determination of energy saving and reduction of discharges of combustion products into the atmosphere is represented in the article. Multifunctional diagram is developed, allowing to determine simultaneously savings from reduction of volumes of natural gas combusted and from reduction of amounts of harmful agents in the combustion products discharged into the atmosphere. Calculation of natural gas economy for heat producing plant taking into consideration certain capacity is carried out.

Alpha spectrometric characterization of process-related particle size distributions from active particle sampling at the Los Alamos National Laboratory uranium foundry

NASA Astrophysics Data System (ADS)

Plionis, A. A.; Peterson, D. S.; Tandon, L.; LaMont, S. P.

2010-03-01

Uranium particles within the respirable size range pose a significant hazard to the health and safety of workers. Significant differences in the deposition and incorporation patterns of aerosols within the respirable range can be identified and integrated into sophisticated health physics models. Data characterizing the uranium particle size distribution resulting from specific foundry-related processes are needed. Using personal air sampling cascade impactors, particles collected from several foundry processes were sorted by activity median aerodynamic diameter onto various Marple substrates. After an initial gravimetric assessment of each impactor stage, the substrates were analyzed by alpha spectrometry to determine the uranium content of each stage. Alpha spectrometry provides rapid non-distructive isotopic data that can distinguish process uranium from natural sources and the degree of uranium contribution to the total accumulated particle load. In addition, the particle size bins utilized by the impactors provide adequate resolution to determine if a process particle size distribution is: lognormal, bimodal, or trimodal. Data on process uranium particle size values and distributions facilitate the development of more sophisticated and accurate models for internal dosimetry, resulting in an improved understanding of foundry worker health and safety.

Determinants of job stress in chemical process industry: A factor analysis approach.

PubMed

Menon, Balagopal G; Praveensal, C J; Madhu, G

2015-01-01

Job stress is one of the active research domains in industrial safety research. The job stress can result in accidents and health related issues in workers in chemical process industries. Hence it is important to measure the level of job stress in workers so as to mitigate the same to avoid the worker's safety related problems in the industries. The objective of this study is to determine the job stress factors in the chemical process industry in Kerala state, India. This study also aims to propose a comprehensive model and an instrument framework for measuring job stress levels in the chemical process industries in Kerala, India. The data is collected through a questionnaire survey conducted in chemical process industries in Kerala. The collected data out of 1197 surveys is subjected to principal component and confirmatory factor analysis to develop the job stress factor structure. The factor analysis revealed 8 factors that influence the job stress in process industries. It is also found that the job stress in employees is most influenced by role ambiguity and the least by work environment. The study has developed an instrument framework towards measuring job stress utilizing exploratory factor analysis and structural equation modeling.

Use of IT platform in determination of efficiency of mining machines

NASA Astrophysics Data System (ADS)

Brodny, Jarosław; Tutak, Magdalena

2018-01-01

Determination of effective use of mining devices has very significant meaning for mining enterprises. High costs of their purchase and tenancy cause that these enterprises tend to the best use of possessed technical potential. However, specifics of mining production causes that this process not always proceeds without interferences. Practical experiences show that determination of objective measure of utilization of machine in mining enterprise is not simple. In the paper a proposition for solution of this problem is presented. For this purpose an IT platform and overall efficiency model OEE were used. This model enables to evaluate the machine in a range of its availability performance and quality of product, and constitutes a quantitative tool of TPM strategy. Adapted to the specificity of mining branch the OEE model together with acquired data from industrial automatic system enabled to determine the partial indicators and overall efficiency of tested machines. Studies were performed for a set of machines directly use in coal exploitation process. They were: longwall-shearer and armoured face conveyor, and beam stage loader. Obtained results clearly indicate that degree of use of machines by mining enterprises are unsatisfactory. Use of IT platforms will significantly facilitate the process of registration, archiving and analytical processing of the acquired data. In the paper there is presented methodology of determination of partial indices and total OEE together with a practical example of its application for investigated machines set. Also IT platform was characterized for its construction, function and application.

Development of processing diagrams for polymeric die attach adhesives

NASA Astrophysics Data System (ADS)

Hsiung, Jen-Chou

With a processing diagram, one can reduce the effort required to customize curing process conditions for polymeric die attach adhesives. Polymeric die attach adhesives are often cured per the manufacturer's recommendations during initial screening evaluations. In most cases, the recommended cure schedules have to be modified so as to fit differences in process equipment. Unfortunately, the modified cure schedule is usually determined by a trial-and-error method. An aim of our experiments is to understand the curing process of a wide range of polymeric die attach adhesives (conventional, fast, and snap cure adhesives) and to construct a processing diagram, i.e., "Bondability Diagram", so as to define the processing window. Such diagrams should be helpful in determining both the time and cure temperature required to produce high quality bonds. The bondability diagram can be constructed based on fundamental understandings of the phenomena involved in the curing process using a wide variety of tools. Differential Scanning Calorimetry (DSC) is utilized to study the cure kinetics and the extent of reaction. Dynamic Mechanical Analysis (DMA) is used to determine gelation times and melt viscosity under a shear mode. A modified Rheovibron is employed to perform cure characterizations under a tensile mode so that cure stresses could be determined. Thermogravimetric Analysis (TGA) is used to evaluate the outgassing phenomena. Optical Microscopy (OM) is used to detect voids. Results indicate that the cure behaviors of conventional, fast, and snap cure adhesives are different in several respects. The combination of DSC, DMA, TGA, OM, and lap shear test leads to a frame work of developing the bondability diagram concept. The bondability diagram concept provides a foundation for an understanding of the recommended cure schedule and allows one to design their own cure schedule.

Physiology and Genetics of Biogenic Methane-Production from Acetate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sowers, Kevin R

Biomass conversion catalyzed by methanogenic consortia is a widely available, renewable resource for both energy production and waste treatment. The efficiency of this process is directly dependent upon the interaction of three metabolically distinct groups of microorganisms; the fermentative and acetogenic Bacteria and the methanogenic Archaea. One of the rate limiting steps in the degradation of soluble organic matter is the dismutation of acetate, a predominant intermediate in the process, which accounts for 70 % or more of the methane produced by the methanogens. Acetate utilization is controlled by regulation of expression of carbon monoxide dehydrogensase (COdh), which catalyzes themore » dismutation of acetate. However, physiological and molecular factors that control differential substrate utilization have not been identified in these Archaea. Our laboratory has identified sequence elements near the promoter of the gene (cdh) encoding for COdh and we have confirmed that these sequences have a role in the in vivo expression of cdh. The current proposal focuses on identifying the regulatory components that interact with DNA and RNA elements, and identifying the mechanisms used to control cdh expression. We will determine whether expression is controlled at the level of transcription or if it is mediated by coordinate interaction of transcription initiation with other processes such as transcription elongation rate and differential mRNA stability. Utilizing recently sequenced methanosarcinal genomes and a DNA microarray currently under development genes that encode regulatory proteins and transcription factors will be identified and function confirmed by gene disruption and subsequent screening on different substrates. Functional interactions will be determined in vivo by assaying the effects of gene dosage and site-directed mutagenesis of the regulatory gene on the expression of a cdh::lacZ operon fusion. Results of this study will reveal whether this critical catabolic pathway is controlled by mechanisms similar to those employed by the Bacteria and Eukarya, or by a regulatory paradigm that is unique to the Archaea. The mechanism(s) revealed by this investigation will provide insight into the regulatory strategies employed by the aceticlastic methanogenic Archaea to efficiently direct carbon and electron flow in anaerobic consortia during fermentative processes.« less

Mechanism of oil bank formation, coalescence in porous media and emulsion and foam stability. Quarterly research progress report, July 1, 1984-September 30, 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wasan, D.T.

The relative permeability model for two phase flow in porous media (Wasan 1983; Ramakrishnan and Wasan 1984) provides the necessary fractional flow curves at a given capillary number. These curves can be utilized in modeling both enhanced secondary and tertiary recovery processes. Important parameters in the fractional flow curves of our relative permeability model are the residual wetting and nonwetting phase saturations in a low capillary number flooding process. To understand, what constitutes the residual saturations, this quarter we have studied the displacement of one incompressible fluid by another in a porous medium using the network representation. The Bernoulli percolationmore » model for an infinite lattice graph is utilized in the interpretation of the capillary behavior of the medium, which ultimately determines residual saturations. The calculated capillary pressure-saturation relationship using Bethe lattice results agrees qualitatively with experimental data. 4 references, 2 figures.« less

Influence of Cobalt on the Properties of Load-Sensitive Magnesium Alloys

PubMed Central

Klose, Christian; Demminger, Christian; Mroz, Gregor; Reimche, Wilfried; Bach, Friedrich-Wilhelm; Maier, Hans Jürgen; Kerber, Kai

2013-01-01

In this study, magnesium is alloyed with varying amounts of the ferromagnetic alloying element cobalt in order to obtain lightweight load-sensitive materials with sensory properties which allow an online-monitoring of mechanical forces applied to components made from Mg-Co alloys. An optimized casting process with the use of extruded Mg-Co powder rods is utilized which enables the production of magnetic magnesium alloys with a reproducible Co concentration. The efficiency of the casting process is confirmed by SEM analyses. Microstructures and Co-rich precipitations of various Mg-Co alloys are investigated by means of EDS and XRD analyses. The Mg-Co alloys' mechanical strengths are determined by tensile tests. Magnetic properties of the Mg-Co sensor alloys depending on the cobalt content and the acting mechanical load are measured utilizing the harmonic analysis of eddy-current signals. Within the scope of this work, the influence of the element cobalt on magnesium is investigated in detail and an optimal cobalt concentration is defined based on the performed examinations. PMID:23344376

Biomedical application of wavelets: analysis of electroencephalograph signals for monitoring depth of anesthesia

NASA Astrophysics Data System (ADS)

Abbate, Agostino; Nayak, A.; Koay, J.; Roy, R. J.; Das, Pankaj K.

1996-03-01

The wavelet transform (WT) has been used to study the nonstationary information in the electroencephalograph (EEG) as an aid in determining the anesthetic depth. A complex analytic mother wavelet is utilized to obtain the time evolution of the various spectral components of the EEG signal. The technique is utilized for the detection and spectral analysis of transient and background processes in the awake and asleep states. It can be observed that the response of both states before the application of the stimulus is similar in amplitude but not in spectral contents, which suggests a background activity of the brain. The brain reacts to the external stimulus in two different modes depending on the state of consciousness of the subject. In the case of awake state, there is an evident increase in response, while for the sleep state a reduction in this activity is observed. This analysis seems to suggest that the brain has an ongoing background process that monitors external stimulus in both the sleep and awake states.

Metabolic behavior and enzymatic aspects of denitrifying EBPR sludge in a continuous-flow anaerobic-anoxic system.

PubMed

Zafiriadis, Ilias; Ntougias, Spyridon; Kapagiannidis, Anastasios G; Aivasidis, Alexander

2013-10-01

The metabolic aspects of enhanced biological phosphorus removal (EBPR) were investigated for the first time in a continuous-flow anaerobic-anoxic plant fed with acetate, propionate, or substrates which are involved in the tricarboxylic acid and/or glyoxylate cycle, i.e., fumarate, malate, or oxaloacetate, as the sole carbon source. Although the polyphosphate-accumulating organisms (PAOs) population remained stable with any carbon source examined, no typical EBPR metabolism was observed during fumarate, malate, or oxaloacetate utilization. Specific enzymatic activities related to EBPR were determined in activated sludge homogenates and directly correlated with the nutrient metabolic rates. The experimental results indicated the direct involvement of alkaline phosphatase, pyrophosphatase, and exopolyphosphatase in the denitrifying EBPR process. Metabolic aspects of glyoxylate cycle enzymes are discussed with regard to the biomass anaerobic and anoxic activity. Process performance was highly influenced by the kind of substrate utilized, indicating that specific metabolic pathways should be followed to favor efficient EBPR.

Using Histories to Implement Atomic Objects

NASA Technical Reports Server (NTRS)

Ng, Pui

1987-01-01

In this paper we describe an approach of implementing atomicity. Atomicity requires that computations appear to be all-or-nothing and executed in a serialization order. The approach we describe has three characteristics. First, it utilizes the semantics of an application to improve concurrency. Second, it reduces the complexity of application-dependent synchronization code by analyzing the process of writing it. In fact, the process can be automated with logic programming. Third, our approach hides the protocol used to arrive at a serialization order from the applications. As a result, different protocols can be used without affecting the applications. Our approach uses a history tree abstraction. The history tree captures the ordering relationship among concurrent computations. By determining what types of computations exist in the history tree and their parameters, a computation can determine whether it can proceed.

Strategies for Utilizing Neuroimaging Biomarkers in CNS Drug Discovery and Development: CINP/JSNP Working Group Report.

PubMed

Suhara, Tetsuya; Chaki, Shigeyuki; Kimura, Haruhide; Furusawa, Makoto; Matsumoto, Mitsuyuki; Ogura, Hiroo; Negishi, Takaaki; Saijo, Takeaki; Higuchi, Makoto; Omura, Tomohiro; Watanabe, Rira; Miyoshi, Sosuke; Nakatani, Noriaki; Yamamoto, Noboru; Liou, Shyh-Yuh; Takado, Yuhei; Maeda, Jun; Okamoto, Yasumasa; Okubo, Yoshiaki; Yamada, Makiko; Ito, Hiroshi; Walton, Noah M; Yamawaki, Shigeto

2017-04-01

Despite large unmet medical needs in the field for several decades, CNS drug discovery and development has been largely unsuccessful. Biomarkers, particularly those utilizing neuroimaging, have played important roles in aiding CNS drug development, including dosing determination of investigational new drugs (INDs). A recent working group was organized jointly by CINP and Japanese Society of Neuropsychopharmacology (JSNP) to discuss the utility of biomarkers as tools to overcome issues of CNS drug development.The consensus statement from the working group aimed at creating more nuanced criteria for employing biomarkers as tools to overcome issues surrounding CNS drug development. To accomplish this, a reverse engineering approach was adopted, in which criteria for the utilization of biomarkers were created in response to current challenges in the processes of drug discovery and development for CNS disorders. Based on this analysis, we propose a new paradigm containing 5 distinct tiers to further clarify the use of biomarkers and establish new strategies for decision-making in the context of CNS drug development. Specifically, we discuss more rational ways to incorporate biomarker data to determine optimal dosing for INDs with novel mechanisms and targets, and propose additional categorization criteria to further the use of biomarkers in patient stratification and clinical efficacy prediction. Finally, we propose validation and development of new neuroimaging biomarkers through public-private partnerships to further facilitate drug discovery and development for CNS disorders. © The Author 2016. Published by Oxford University Press on behalf of CINP.

Using a Smartphone Camera for Nanosatellite Attitude Determination

NASA Astrophysics Data System (ADS)

Shimmin, R.

2014-09-01

The PhoneSat project at NASA Ames Research Center has repeatedly flown a commercial cellphone in space. As this project continues, additional utility is being extracted from the cell phone hardware to enable more complex missions. The camera in particular shows great potential as an instrument for position and attitude determination, but this requires complex image processing. This paper outlines progress towards that image processing capability. Initial tests on a small collection of sample images have demonstrated the determination of a Moon vector from an image by automatic thresholding and centroiding, allowing the calibration of existing attitude control systems. Work has been undertaken on a further set of sample images towards horizon detection using a variety of techniques including thresholding, edge detection, applying a Hough transform, and circle fitting. Ultimately it is hoped this will allow calculation of an Earth vector for attitude determination and an approximate altitude. A quick discussion of work towards using the camera as a star tracker is then presented, followed by an introduction to further applications of the camera on space missions.

Estimating satellite pose and motion parameters using a novelty filter and neural net tracker

NASA Technical Reports Server (NTRS)

Lee, Andrew J.; Casasent, David; Vermeulen, Pieter; Barnard, Etienne

1989-01-01

A system for determining the position, orientation and motion of a satellite with respect to a robotic spacecraft using video data is advanced. This system utilizes two levels of pose and motion estimation: an initial system which provides coarse estimates of pose and motion, and a second system which uses the coarse estimates and further processing to provide finer pose and motion estimates. The present paper emphasizes the initial coarse pose and motion estimation sybsystem. This subsystem utilizes novelty detection and filtering for locating novel parts and a neural net tracker to track these parts over time. Results of using this system on a sequence of images of a spin stabilized satellite are presented.

Fast depth decision for HEVC inter prediction based on spatial and temporal correlation

NASA Astrophysics Data System (ADS)

Chen, Gaoxing; Liu, Zhenyu; Ikenaga, Takeshi

2016-07-01

High efficiency video coding (HEVC) is a video compression standard that outperforms the predecessor H.264/AVC by doubling the compression efficiency. To enhance the compression accuracy, the partition sizes ranging is from 4x4 to 64x64 in HEVC. However, the manifold partition sizes dramatically increase the encoding complexity. This paper proposes a fast depth decision based on spatial and temporal correlation. Spatial correlation utilize the code tree unit (CTU) Splitting information and temporal correlation utilize the motion vector predictor represented CTU in inter prediction to determine the maximum depth in each CTU. Experimental results show that the proposed method saves about 29.1% of the original processing time with 0.9% of BD-bitrate increase on average.

Shareholder interests and utility competition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Studness, C.M.

1995-03-15

The process of determining how to implement utility competition is often cast as a struggle between two opposing camps: shareholders and ratepayers. There are, of course, two other major players, management and regulators. The bipolar view tacitly assumes that shareholder and management interests coincide and that regulators have customer interests at heart. Neither assumption is valid. Shareholder interests deviate from management interests in important ways, just as the interests of the entrenched regulatory bureaucracy diverge from the public interest. Therefore, shareholder and management interests must be considered separately. In the past, managements have often pursued their own interests, with devastatingmore » financial impact on shareholders. Competition offers shareholders an opportunity to increase their leverage over managements, thereby increasing their returns as well.« less

Computer aided stress analysis of long bones utilizing computer tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marom, S.A.

1986-01-01

A computer aided analysis method, utilizing computed tomography (CT) has been developed, which together with a finite element program determines the stress-displacement pattern in a long bone section. The CT data file provides the geometry, the density and the material properties for the generated finite element model. A three-dimensional finite element model of a tibial shaft is automatically generated from the CT file by a pre-processing procedure for a finite element program. The developed pre-processor includes an edge detection algorithm which determines the boundaries of the reconstructed cross-sectional images of the scanned bone. A mesh generation procedure than automatically generatesmore » a three-dimensional mesh of a user-selected refinement. The elastic properties needed for the stress analysis are individually determined for each model element using the radiographic density (CT number) of each pixel with the elemental borders. The elastic modulus is determined from the CT radiographic density by using an empirical relationship from the literature. The generated finite element model, together with applied loads, determined from existing gait analysis and initial displacements, comprise a formatted input for the SAP IV finite element program. The output of this program, stresses and displacements at the model elements and nodes, are sorted and displayed by a developed post-processor to provide maximum and minimum values at selected locations in the model.« less

Systematic wavelength selection for improved multivariate spectral analysis

DOEpatents

Thomas, Edward V.; Robinson, Mark R.; Haaland, David M.

1995-01-01

Methods and apparatus for determining in a biological material one or more unknown values of at least one known characteristic (e.g. the concentration of an analyte such as glucose in blood or the concentration of one or more blood gas parameters) with a model based on a set of samples with known values of the known characteristics and a multivariate algorithm using several wavelength subsets. The method includes selecting multiple wavelength subsets, from the electromagnetic spectral region appropriate for determining the known characteristic, for use by an algorithm wherein the selection of wavelength subsets improves the model's fitness of the determination for the unknown values of the known characteristic. The selection process utilizes multivariate search methods that select both predictive and synergistic wavelengths within the range of wavelengths utilized. The fitness of the wavelength subsets is determined by the fitness function F=.function.(cost, performance). The method includes the steps of: (1) using one or more applications of a genetic algorithm to produce one or more count spectra, with multiple count spectra then combined to produce a combined count spectrum; (2) smoothing the count spectrum; (3) selecting a threshold count from a count spectrum to select these wavelength subsets which optimize the fitness function; and (4) eliminating a portion of the selected wavelength subsets. The determination of the unknown values can be made: (1) noninvasively and in vivo; (2) invasively and in vivo; or (3) in vitro.

Cell fate determination dynamics in bacteria

NASA Astrophysics Data System (ADS)

Kuchina, Anna; Espinar, Lorena; Cagatay, Tolga; Garcia-Ojalvo, Jordi; Suel, Gurol

2010-03-01

The fitness of an organism depends on many processes that serve the purpose to adapt to changing environment in a robust and coordinated fashion. One example of such process is cellular fate determination. In the presence of a variety of alternative responses each cell adopting a particular fate represents a ``choice'' that must be tightly regulated to ensure the best survival strategy for the population taking into account the broad range of possible environmental challenges. We investigated this problem in the model organism B.Subtilis which under stress conditions differentiates terminally into highly resistant spores or initiates an alternative transient state of competence. The dynamics underlying cell fate choice remains largely unknown. We utilize quantitative fluorescent microscopy to track the activities of genes involved in these responses on a single-cell level. We explored the importance of temporal interactions between competing cell fates by re- engineering the differentiation programs. I will discuss how the precise dynamics of cellular ``decision-making'' governed by the corresponding biological circuits may enable cells to adjust to diverse environments and determine survival.

Development of materials for the rapid manufacture of die cast tooling

NASA Astrophysics Data System (ADS)

Hardro, Peter Jason

The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely, reduce tooling cost, shorten tooling creation time, and reduce the man-hours needed for tool creation. Though identifying the appropriate time to use RP tooling appears to be the most important aspect in achieving successful implementation.

Does resident ranking during recruitment accurately predict subsequent performance as a surgical resident?

PubMed

Fryer, Jonathan P; Corcoran, Noreen; George, Brian; Wang, Ed; Darosa, Debra

2012-01-01

While the primary goal of ranking applicants for surgical residency training positions is to identify the candidates who will subsequently perform best as surgical residents, the effectiveness of the ranking process has not been adequately studied. We evaluated our general surgery resident recruitment process between 2001 and 2011 inclusive, to determine if our recruitment ranking parameters effectively predicted subsequent resident performance. We identified 3 candidate ranking parameters (United States Medical Licensing Examination [USMLE] Step 1 score, unadjusted ranking score [URS], and final adjusted ranking [FAR]), and 4 resident performance parameters (American Board of Surgery In-Training Examination [ABSITE] score, PGY1 resident evaluation grade [REG], overall REG, and independent faculty rating ranking [IFRR]), and assessed whether the former were predictive of the latter. Analyses utilized Spearman correlation coefficient. We found that the URS, which is based on objective and criterion based parameters, was a better predictor of subsequent performance than the FAR, which is a modification of the URS based on subsequent determinations of the resident selection committee. USMLE score was a reliable predictor of ABSITE scores only. However, when we compared our worst residence performances with the performances of the other residents in this evaluation, the data did not produce convincing evidence that poor resident performances could be reliably predicted by any of the recruitment ranking parameters. Finally, stratifying candidates based on their rank range did not effectively define a ranking cut-off beyond which resident performance would drop off. Based on these findings, we recommend surgery programs may be better served by utilizing a more structured resident ranking process and that subsequent adjustments to the rank list generated by this process should be undertaken with caution. Copyright © 2012 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Lightweight DC-DC Converter with Partial Power Processing and MPPT for a Solar Powered Aircraft

NASA Astrophysics Data System (ADS)

Diab-Marzouk, Ahmad

A lightweight dc-dc partial power processing converter is demonstrated for solar aerospace applications. A system-level model is conceived to determine conformity to payload and target distance objectives, with the Solarship aircraft used as an application example. The concept of partial power processing is utilized to realize a high efficiency lightweight converter that performs Max Peak Power Tracking (MPPT) to transfer power from the aircraft solar array to the high-voltage battery bus. The isolated Cuk is determined to be a suitable converter topology for the application. A small-signal model is derived for control design. The operation of a 400V, 2.7 kW prototype is verified at high frequency (200 kHz), high efficiency (> 98%), small mass (0.604 kg), and uses no electrolytic capacitors. MPPT operation is verified on a 376 V commercial solar installation at The University of Toronto. The prototype serves as an enabling technology for solar aerospace applications.

Definition and determination of the triplet-triplet energy transfer reaction coordinate.

PubMed

Zapata, Felipe; Marazzi, Marco; Castaño, Obis; Acuña, A Ulises; Frutos, Luis Manuel

2014-01-21

A definition of the triplet-triplet energy transfer reaction coordinate within the very weak electronic coupling limit is proposed, and a novel theoretical formalism is developed for its quantitative determination in terms of internal coordinates The present formalism permits (i) the separation of donor and acceptor contributions to the reaction coordinate, (ii) the identification of the intrinsic role of donor and acceptor in the triplet energy transfer process, and (iii) the quantification of the effect of every internal coordinate on the transfer process. This formalism is general and can be applied to classical as well as to nonvertical triplet energy transfer processes. The utility of the novel formalism is demonstrated here by its application to the paradigm of nonvertical triplet-triplet energy transfer involving cis-stilbene as acceptor molecule. In this way the effect of each internal molecular coordinate in promoting the transfer rate, from triplet donors in the low and high-energy limit, could be analyzed in detail.

A lexicographic weighted Tchebycheff approach for multi-constrained multi-objective optimization of the surface grinding process

NASA Astrophysics Data System (ADS)

Khalilpourazari, Soheyl; Khalilpourazary, Saman

2017-05-01

In this article a multi-objective mathematical model is developed to minimize total time and cost while maximizing the production rate and surface finish quality in the grinding process. The model aims to determine optimal values of the decision variables considering process constraints. A lexicographic weighted Tchebycheff approach is developed to obtain efficient Pareto-optimal solutions of the problem in both rough and finished conditions. Utilizing a polyhedral branch-and-cut algorithm, the lexicographic weighted Tchebycheff model of the proposed multi-objective model is solved using GAMS software. The Pareto-optimal solutions provide a proper trade-off between conflicting objective functions which helps the decision maker to select the best values for the decision variables. Sensitivity analyses are performed to determine the effect of change in the grain size, grinding ratio, feed rate, labour cost per hour, length of workpiece, wheel diameter and downfeed of grinding parameters on each value of the objective function.

Definition and determination of the triplet-triplet energy transfer reaction coordinate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zapata, Felipe; Marazzi, Marco; Castaño, Obis

2014-01-21

A definition of the triplet-triplet energy transfer reaction coordinate within the very weak electronic coupling limit is proposed, and a novel theoretical formalism is developed for its quantitative determination in terms of internal coordinates The present formalism permits (i) the separation of donor and acceptor contributions to the reaction coordinate, (ii) the identification of the intrinsic role of donor and acceptor in the triplet energy transfer process, and (iii) the quantification of the effect of every internal coordinate on the transfer process. This formalism is general and can be applied to classical as well as to nonvertical triplet energy transfermore » processes. The utility of the novel formalism is demonstrated here by its application to the paradigm of nonvertical triplet-triplet energy transfer involving cis-stilbene as acceptor molecule. In this way the effect of each internal molecular coordinate in promoting the transfer rate, from triplet donors in the low and high-energy limit, could be analyzed in detail.« less

Utilization of starch films plasticized with urea as fertilizer for improvement of plant growth.

PubMed

Rychter, Piotr; Kot, Marta; Bajer, Krzysztof; Rogacz, Diana; Šišková, Alena; Kapuśniak, Janusz

2016-02-10

The utilization of starch films, obtained by extrusion of potato starch with urea as plasticizer, for the fertilization of plants has been undertaken. Release rate of urea from the starch films was conducted in water conditions. The molecular weight distribution, surface erosion and weight loss of the starch samples have been determined. The evaluation of efficiency of urea as a fertilizer in the process of release from the starch films was performed under laboratory conditions based on the plant growth test proposed by OECD 208 Guideline and the PN-ISO International Standard using oat and common radish. Although among extruded starch-based films, those that contain the highest amount of fertilizer hold the most promise for a delayed release system, the time of release of fertilizer from obtained films in undertaken study was not satisfactory. All the same, in the present study effort has been made to utilize extruded samples as a fertilizer for agriculture or horticulture purposes. Urea-plasticized starch was successfully used as a fertilizer. Plant growth assessment, including determination of such parameters as fresh and dry matter of plants and their visual evaluation, has proved the stimulating effect of using extruded films on the growth and development of cultivated plants. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Process Analysis of the Uniform Chart of Accounts Personnel Utilization System

DTIC Science & Technology

2002-04-23

business practices is evolving rapidly. The ever- changing health care environment requires all providers to be familiar with the costs of each...advised the standardization of the data used to develop them as well as the formulas for calculating them. These changes mostly related to workload...can also be used to determine site-specific capabilities and to identify potential areas for inter - service support of workload through sharing of

Rigid-Flex Printed Circuit Manufacturing process. A Project of the Manufacturing Technology Program.

DTIC Science & Technology

1979-06-30

utilized epoxy glass laminate stiffeners in order to improve drilling characteristics, prevent thermal damage created by Z-axis expansion, and increase...temperatures. I 41 6. Fortin Laminates 1323 Truman Street San Fernando, CA q1340 7. Howe Industries 13704 Saticoy Street Panorama City, CA 8. Atl antic...to determine thickness, inner layer continuity and uniformity). In addition, tests such as thermal shock and thermal stress (per MIL-P-55640) were

A Method to Determine an Organization’s Compatibility with Hybrid Workspaces

DTIC Science & Technology

2014-03-27

workers were present and assumed to be working. As early as the 1980s , private sector organizations began to evolve from task-based work to process...fact that people may utilize multiple physical spaces to conduct work ( Hislop & Axtell 2007). This is an important difference to consider when...on a flexible basis (Kunkle, 2000). Hislop and Axtell (2007) discovered that multiple studies compared the performances of teleworkers to those

Solar Heating And Cooling Of Buildings (SHACOB): Requirements definition and impact analysis-2. Volume 3: Customer load management systems

NASA Astrophysics Data System (ADS)

Cretcher, C. K.; Rountredd, R. C.

1980-11-01

Customer Load Management Systems, using off-peak storage and control at the residences, are analyzed to determine their potential for capacity and energy savings by the electric utility. Areas broadly representative of utilities in the regions around Washington, DC and Albuquerque, NM were of interest. Near optimum tank volumes were determined for both service areas, and charging duration/off-time were identified as having the greatest influence on tank performance. The impacts on utility operations and corresponding utility/customer economics were determined in terms of delta demands used to estimate the utilities' generating capacity differences between the conventional load management, (CLM) direct solar with load management (DSLM), and electric resistive systems. Energy differences are also determined. These capacity and energy deltas are translated into changes in utility costs due to penetration of the CLM or DSLM systems into electric resistive markets in the snapshot years of 1990 and 2000.

Urban area delineation and detection of change along the urban-rural boundary as derived from LANDSAT digital data

NASA Technical Reports Server (NTRS)

Christenson, J. W.; Lachowski, H. M.

1977-01-01

LANDSAT digital multispectral scanner data, in conjunction with supporting ground truth, were investigated to determine their utility in delineation of urban-rural boundaries. The digital data for the metropolitan areas of Washington, D. C.; Austin, Texas; and Seattle, Washingtion; were processed using an interactive image processing system. Processing focused on identification of major land cover types typical of the zone of transition from urban to rural landscape, and definition of their spectral signatures. Census tract boundaries were input into the interactive image processing system along with the LANDSAT single and overlayed multiple date MSS data. Results of this investigation indicate that satellite collected information has a practical application to the problem of urban area delineation and to change detection.

A programmable nanoreplica molding for the fabrication of nanophotonic devices.

PubMed

Liu, Longju; Zhang, Jingxiang; Badshah, Mohsin Ali; Dong, Liang; Li, Jingjing; Kim, Seok-min; Lu, Meng

2016-03-01

The ability to fabricate periodic structures with sub-wavelength features has a great potential for impact on integrated optics, optical sensors, and photovoltaic devices. Here, we report a programmable nanoreplica molding process to fabricate a variety of sub-micrometer periodic patterns using a single mold. The process utilizes a stretchable mold to produce the desired periodic structure in a photopolymer on glass or plastic substrates. During the replica molding process, a uniaxial force is applied to the mold and results in changes of the periodic structure, which resides on the surface of the mold. Direction and magnitude of the force determine the array geometry, including the lattice constant and arrangement. By stretching the mold, 2D arrays with square, rectangular, and triangular lattice structures can be fabricated. As one example, we present a plasmonic crystal device with surface plasmon resonances determined by the force applied during molding. In addition, photonic crystal slabs with different array patterns are fabricated and characterized. This unique process offers the capability of generating various periodic nanostructures rapidly and inexpensively.

A programmable nanoreplica molding for the fabrication of nanophotonic devices

PubMed Central

Liu, Longju; Zhang, Jingxiang; Badshah, Mohsin Ali; Dong, Liang; Li, Jingjing; Kim, Seok-min; Lu, Meng

2016-01-01

The ability to fabricate periodic structures with sub-wavelength features has a great potential for impact on integrated optics, optical sensors, and photovoltaic devices. Here, we report a programmable nanoreplica molding process to fabricate a variety of sub-micrometer periodic patterns using a single mold. The process utilizes a stretchable mold to produce the desired periodic structure in a photopolymer on glass or plastic substrates. During the replica molding process, a uniaxial force is applied to the mold and results in changes of the periodic structure, which resides on the surface of the mold. Direction and magnitude of the force determine the array geometry, including the lattice constant and arrangement. By stretching the mold, 2D arrays with square, rectangular, and triangular lattice structures can be fabricated. As one example, we present a plasmonic crystal device with surface plasmon resonances determined by the force applied during molding. In addition, photonic crystal slabs with different array patterns are fabricated and characterized. This unique process offers the capability of generating various periodic nanostructures rapidly and inexpensively. PMID:26925828

Parameter estimation supplement to the Mission Analysis Evaluation and Space Trajectory Operations program (MAESTRO)

NASA Technical Reports Server (NTRS)

Bjorkman, W. S.; Uphoff, C. W.

1973-01-01

This Parameter Estimation Supplement describes the PEST computer program and gives instructions for its use in determination of lunar gravitation field coefficients. PEST was developed for use in the RAE-B lunar orbiting mission as a means of lunar field recovery. The observations processed by PEST are short-arc osculating orbital elements. These observations are the end product of an orbit determination process obtained with another program. PEST's end product it a set of harmonic coefficients to be used in long-term prediction of the lunar orbit. PEST employs some novel techniques in its estimation process, notably a square batch estimator and linear variational equations in the orbital elements (both osculating and mean) for measurement sensitivities. The program's capabilities are described, and operating instructions and input/output examples are given. PEST utilizes MAESTRO routines for its trajectory propagation. PEST's program structure and subroutines which are not common to MAESTRO are described. Some of the theoretical background information for the estimation process, and a derivation of linear variational equations for the Method 7 elements are included.

Lab-On-a-Chip Application Development (LOCAD): Bridging Technology Readiness for Exploration

NASA Technical Reports Server (NTRS)

Spearing, Scott F.; Jenkins, Andy

2004-01-01

At Marshall Space Flight Center we have established a capability to investigate the use of microfluidics for space flight. The Lab-On-a-Chip Application Development (LOCAD) team has created a program for advancing Technology Readiness Levels (TRL) of 1 and 2 to TRL 6 and 7, quickly and economically for Lab-On-a-Chip (LOC) applications. Scientists and engineers can utilize LOCAD'S process to efficiently learn about microfluidics and determine if microfluidics is applicable to their needs. Once the applicability has been determined, LOCAD can then perform tests to develop the new fluidic protocols which are different from macro-scale chemical reaction protocols. With this information new micro-fluidic devices can be created and tested. Currently, LOCAD is focused on using microfluidics for both Environmental Monitoring & Control, and Medical Systems. Eventually, handheld portable units utilizing LOC technology will perform rapid tests to determine water quality, and microbial contamination levels. Since LOC technology is drastically reduced in physical size, it thereby reduces power, weight, volume, and sample requirements, a big advantage considering the resource constraints associated with spaceflight. Another one of LOCAD's current activities is the development of a microfluidic system to aid in the search for life on Mars.

Cross-cultural adaptation of instruments assessing breastfeeding determinants: a multi-step approach

PubMed Central

2014-01-01

Background Cross-cultural adaptation is a necessary process to effectively use existing instruments in other cultural and language settings. The process of cross-culturally adapting, including translation, of existing instruments is considered a critical set to establishing a meaningful instrument for use in another setting. Using a multi-step approach is considered best practice in achieving cultural and semantic equivalence of the adapted version. We aimed to ensure the content validity of our instruments in the cultural context of KwaZulu-Natal, South Africa. Methods The Iowa Infant Feeding Attitudes Scale, Breastfeeding Self-Efficacy Scale-Short Form and additional items comprise our consolidated instrument, which was cross-culturally adapted utilizing a multi-step approach during August 2012. Cross-cultural adaptation was achieved through steps to maintain content validity and attain semantic equivalence in the target version. Specifically, Lynn’s recommendation to apply an item-level content validity index score was followed. The revised instrument was translated and back-translated. To ensure semantic equivalence, Brislin’s back-translation approach was utilized followed by the committee review to address any discrepancies that emerged from translation. Results Our consolidated instrument was adapted to be culturally relevant and translated to yield more reliable and valid results for use in our larger research study to measure infant feeding determinants effectively in our target cultural context. Conclusions Undertaking rigorous steps to effectively ensure cross-cultural adaptation increases our confidence that the conclusions we make based on our self-report instrument(s) will be stronger. In this way, our aim to achieve strong cross-cultural adaptation of our consolidated instruments was achieved while also providing a clear framework for other researchers choosing to utilize existing instruments for work in other cultural, geographic and population settings. PMID:25285151

Automated target classification in high resolution dual frequency sonar imagery

NASA Astrophysics Data System (ADS)

Aridgides, Tom; Fernández, Manuel

2007-04-01

An improved computer-aided-detection / computer-aided-classification (CAD/CAC) processing string has been developed. The classified objects of 2 distinct strings are fused using the classification confidence values and their expansions as features, and using "summing" or log-likelihood-ratio-test (LLRT) based fusion rules. The utility of the overall processing strings and their fusion was demonstrated with new high-resolution dual frequency sonar imagery. Three significant fusion algorithm improvements were made. First, a nonlinear 2nd order (Volterra) feature LLRT fusion algorithm was developed. Second, a Box-Cox nonlinear feature LLRT fusion algorithm was developed. The Box-Cox transformation consists of raising the features to a to-be-determined power. Third, a repeated application of a subset feature selection / feature orthogonalization / Volterra feature LLRT fusion block was utilized. It was shown that cascaded Volterra feature LLRT fusion of the CAD/CAC processing strings outperforms summing, baseline single-stage Volterra and Box-Cox feature LLRT algorithms, yielding significant improvements over the best single CAD/CAC processing string results, and providing the capability to correctly call the majority of targets while maintaining a very low false alarm rate. Additionally, the robustness of cascaded Volterra feature fusion was demonstrated, by showing that the algorithm yields similar performance with the training and test sets.

Study of Fluid Experiment System (FES)/CAST/Holographic Ground System (HGS)

NASA Technical Reports Server (NTRS)

Workman, Gary L.; Cummings, Rick; Jones, Brian

1992-01-01

The use of holographic and schlieren optical techniques for studying the concentration gradients in solidification processes has been used by several investigators over the years. The HGS facility at MSFC has been primary resource in researching this capability. Consequently, scientific personnel have been able to utilize these techniques in both ground based research and in space experiments. An important event in the scientific utilization of the HGS facilities was the TGS Crystal Growth and the casting and solidification technology (CAST) experiments that were flown on the International Microgravity Laboratory (IML) mission in March of this year. The preparation and processing of these space observations are the primary experiments reported in this work. This project provides some ground-based studies to optimize on the holographic techniques used to acquire information about the crystal growth processes flown on IML. Since the ground-based studies will be compared with the space-based experimental results, it is necessary to conduct sufficient ground based studies to best determine how the experiment worked in space. The current capabilities in computer based systems for image processing and numerical computation have certainly assisted in those efforts. As anticipated, this study has certainly shown that these advanced computing capabilities are helpful in the data analysis of such experiments.

The intestinal-renal axis for arginine synthesis is present and functional in the neonatal pig.

PubMed

Marini, Juan C; Agarwal, Umang; Robinson, Jason L; Yuan, Yang; Didelija, Inka C; Stoll, Barbara; Burrin, Douglas G

2017-08-01

The intestinal-renal axis for endogenous arginine synthesis is an interorgan process in which citrulline produced in the small intestine is utilized by the kidney for arginine synthesis. The function of this axis in neonates has been questioned because during this period the enzymes needed for arginine synthesis argininosuccinate synthase (ASS1) and lyase (ASL) are present in the gut. However, evidence of high plasma citrulline concentrations in neonates suggests otherwise. We quantified in vivo citrulline production in premature (10 days preterm), neonatal (7 days old), and young pigs (35 days old) using citrulline tracers. Neonatal pigs had higher fluxes (69 µmol·kg -1 ·h -1 , P < 0.001) than premature and young pigs (43 and 45 µmol·kg -1 ·h -1 , respectively). Plasma citrulline concentration was also greater in neonatal pigs than in the other age groups. We also determined the site of synthesis and utilization of citrulline in neonatal and young pigs by measuring organ balances across the gut and the kidney. Citrulline was released from the gut and utilized by the kidney in both neonatal and young pigs. The abundance and localization of the enzymes involved in the synthesis and utilization were determined in intestinal and kidney tissue. Despite the presence of ASS1 and ASL in the neonatal small intestine, the lack of colocalization with the enzymes that produce citrulline results in the release of citrulline by the PDV and its utilization by the kidney to produce arginine. In conclusion, the intestinal-renal axis for arginine synthesis is present in the neonatal pig. Copyright © 2017 the American Physiological Society.

Statistical Tools And Artificial Intelligence Approaches To Predict Fracture In Bulk Forming Processes

NASA Astrophysics Data System (ADS)

Di Lorenzo, R.; Ingarao, G.; Fonti, V.

2007-05-01

The crucial task in the prevention of ductile fracture is the availability of a tool for the prediction of such defect occurrence. The technical literature presents a wide investigation on this topic and many contributions have been given by many authors following different approaches. The main class of approaches regards the development of fracture criteria: generally, such criteria are expressed by determining a critical value of a damage function which depends on stress and strain paths: ductile fracture is assumed to occur when such critical value is reached during the analysed process. There is a relevant drawback related to the utilization of ductile fracture criteria; in fact each criterion usually has good performances in the prediction of fracture for particular stress - strain paths, i.e. it works very well for certain processes but may provide no good results for other processes. On the other hand, the approaches based on damage mechanics formulation are very effective from a theoretical point of view but they are very complex and their proper calibration is quite difficult. In this paper, two different approaches are investigated to predict fracture occurrence in cold forming operations. The final aim of the proposed method is the achievement of a tool which has a general reliability i.e. it is able to predict fracture for different forming processes. The proposed approach represents a step forward within a research project focused on the utilization of innovative predictive tools for ductile fracture. The paper presents a comparison between an artificial neural network design procedure and an approach based on statistical tools; both the approaches were aimed to predict fracture occurrence/absence basing on a set of stress and strain paths data. The proposed approach is based on the utilization of experimental data available, for a given material, on fracture occurrence in different processes. More in detail, the approach consists in the analysis of experimental tests in which fracture occurs followed by the numerical simulations of such processes in order to track the stress-strain paths in the workpiece region where fracture is expected. Such data are utilized to build up a proper data set which was utilized both to train an artificial neural network and to perform a statistical analysis aimed to predict fracture occurrence. The developed statistical tool is properly designed and optimized and is able to recognize the fracture occurrence. The reliability and predictive capability of the statistical method were compared with the ones obtained from an artificial neural network developed to predict fracture occurrence. Moreover, the approach is validated also in forming processes characterized by a complex fracture mechanics.

Search and Determine Integrated Environment (SADIE)

NASA Astrophysics Data System (ADS)

Sabol, C.; Schumacher, P.; Segerman, A.; Coffey, S.; Hoskins, A.

2012-09-01

A new and integrated high performance computing software applications package called the Search and Determine Integrated Environment (SADIE) is being jointly developed and refined by the Air Force and Naval Research Laboratories (AFRL and NRL) to automatically resolve uncorrelated tracks (UCTs) and build a more complete space object catalog for improved Space Situational Awareness (SSA). The motivation for SADIE is to respond to very challenging needs identified and guidance received from Air Force Space Command (AFSPC) and other senior leaders to develop this technology to support the evolving Joint Space Operations Center (JSpOC) and Alternate Space Control Center (ASC2)-Dahlgren. The JSpOC and JMS SSA mission requirements and threads flow down from the United States Strategic Command (USSTRATCOM). The SADIE suite includes modification and integration of legacy applications and software components that include Search And Determine (SAD), Satellite Identification (SID), and Parallel Catalog (Parcat), as well as other utilities and scripts to enable end-to-end catalog building and maintenance in a parallel processing environment. SADIE is being developed to handle large catalog building challenges in all orbit regimes and includes the automatic processing of radar, fence, and optical data. Real data results are provided for the processing of Air Force Space Surveillance System fence observations and for the processing of Space Surveillance Telescope optical data.

Technical and economic assessment of processes for the production of butanol and acetone

NASA Technical Reports Server (NTRS)

1982-01-01

This report represents a preliminary technical and economic evaluation of a process which produces mixed solvents (butaol/acetone/ethanol) via fermentation of sugars derived from renewable biomass resources. The objective is to assess the technology of producing butanol/acetone from biomass, and select a viable process capable of serving as a base case model for technical and economic analysis. It is anticipated that the base case process developed herein can then be used as the basis for subsequent studies concerning biomass conversion processes capable of producing a wide range of chemicals. The general criteria utilized in determining the design basis for the process are profit potential and non-renewable energy displacement potential. The feedstock chosen, aspen wood, was selected from a number of potential renewable biomass resources as the most readily available in the United States and for its relatively large potential for producing reducing sugars.

The utilization of knowledge of and interest in research and development among primary care staff by means of strategic communication - a staff cohort study.

PubMed

Morténius, Helena; Marklund, Bertil; Palm, Lars; Fridlund, Bengt; Baigi, Amir

2012-08-01

The obvious gap between evidence and practice in health care is unfavourable for patient care and requires the promotion of a scientific attitude among health care professionals. The aim of the present study was to determine the utilization of knowledge of and interest in research and development among primary care staff by means of a strategic communication process. A cohort consisting of primary care staff (n = 1276) was designed and strategic communication was utilized as a platform over a 7-year period. Quantitative and qualitative methods were taken in account. We found that 97% of the staff had gained knowledge of research and development, 60% of whom remained interested in the subject. The oral communication channel was the most powerful for creating research interest. Organizational culture was a barrier to interest in science. The study demonstrates a significant increase in knowledge and interest among primary care staff as a result of a strategic communication process. Strategic communication should lead to a more evenly distributed research commitment among all health care professionals, thus facilitating communication between them and patients in order to clarify, for example, the causes of disease. © 2011 Blackwell Publishing Ltd.

Computerized engineering logic for nuclear procurement and dedication processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tulay, M.P.

1996-12-31

In an attempt to better meet the needs of operations and maintenance organizations, many nuclear utility procurement engineering groups have simplified their procedures, developed on-line tools for performing the specification of replacement items, and developed relational databases containing part-level information necessary to automate the procurement process. Although these improvements have helped to reduce the engineering necessary to properly specify and accept/dedicate items for nuclear safety-related applications, a number of utilities have recognized that additional long-term savings can be realized by integrating a computerized logic to assist technical procurement engineering personnel. The most commonly used logic follows the generic processes containedmore » in Electric Power Research Institute (EPRI) published guidelines. The processes are typically customized to some extent to accommodate each utility`s organizational structure, operating procedures, and strategic goals. This paper will discuss a typical logic that integrates the technical evaluation, acceptance, and receipt inspection and testing processes. The logic this paper will describe has been successfully integrated at a growing number of nuclear utilities and has produced numerous positive results. The application of the logic ensures that utility-wide standards or procedures, common among multi-site utilities, are followed.« less

Potential of Cupriavidus metallidurans CH34 for in situ resource utilization from basalt by determining the molecular micro-mineral interactions

NASA Astrophysics Data System (ADS)

Byloos, Bo; Van Houdt, Rob; Boon, Nico; Leys, Natalie

In order to maintain a persistent human presence in space, materials must either be provided from Earth or generated from material already present in space, in a process referred to as 'in situ resource utilization (ISRU)'. Microorganisms can biomine useful elements from extra-terrestrial materials for use as nutrients in a life support system or to aid in the creation of soil. To effectively use bacteria in an ISRU process more needs to be known about the molecular mechanisms behind microbe-mineral interaction and the influence of microgravity and radiation that affect bioleaching. The aim of this research project is to define the microbe-mineral interactions on basalt, which is a major constituent of Lunar or Martian regolith, the mechanisms that are important in bioleaching and how this process will be altered by space flight conditions. In particular, the research will be focussed on the determination of the genes and proteins involved in the biosynthesis of metallophores and exopolysaccharides (EPS), and biofilm formation. Iron, copper and phosphate uptake mechanisms are investigated in detail because these have been shown to be essential for life and bacteria are faced with limitation of these nutrients in the environment. In this study the bacterium Cupriavidus metallidurans CH34 is used to study these interactions. C. metallidurans CH34 is a soil bacterium which is resistant to up to 20 different heavy metal ions. Its behaviour in space has already been determined with earlier flight experiments to the ISS. It was recently discovered that C. metallidurans forms a biofilm and is capable of leaching calcium, magnesium and iron from basalt to sustain its growth First, C. metallidurans was grown in conditions with and without basalt, iron, copper and phosphate and the production of EPS and metallophores was examined. The iron, copper and phosphate concentrations which are limiting and optimal to allow C. metallidurans cell proliferation could be determined as well as how much iron, copper and phosphate was incorporated into its biomass. The conditions in which EPS and metallophores are produced were also examined. Next, comparative microarray analysis and proteomics of C. metallidurans in these different conditions will be performed to determine which genes and proteins were up regulated under the different conditions to identify the mechanisms that aid in bioleaching. Finally, also biofilm formation capacity of C. metallidurans in these different conditions will be investigated to determine if biofilm formation also helps in the bioleaching process.

Nuclear Test Depth Determination with Synthetic Modelling: Global Analysis from PNEs to DPRK-2016

NASA Astrophysics Data System (ADS)

Rozhkov, Mikhail; Stachnik, Joshua; Baker, Ben; Epiphansky, Alexey; Bobrov, Dmitry

2016-04-01

Seismic event depth determination is critical for the event screening process at the International Data Center, CTBTO. A thorough determination of the event depth can be conducted mostly through additional special analysis because the IDC's Event Definition Criteria is based, in particular, on depth estimation uncertainties. This causes a large number of events in the Reviewed Event Bulletin to have depth constrained to the surface making the depth screening criterion not applicable. Further it may result in a heavier workload to manually distinguish between subsurface and deeper crustal events. Since the shape of the first few seconds of signal of very shallow events is very sensitive to the depth phases, cross correlation between observed and theoretic seismograms can provide a basis for the event depth estimation, and so an expansion to the screening process. We applied this approach mostly to events at teleseismic and partially regional distances. The approach was found efficient for the seismic event screening process, with certain caveats related mostly to poorly defined source and receiver crustal models which can shift the depth estimate. An adjustable teleseismic attenuation model (t*) for synthetics was used since this characteristic is not known for most of the rays we studied. We studied a wide set of historical records of nuclear explosions, including so called Peaceful Nuclear Explosions (PNE) with presumably known depths, and recent DPRK nuclear tests. The teleseismic synthetic approach is based on the stationary phase approximation with hudson96 program, and the regional modelling was done with the generalized ray technique by Vlastislav Cerveny modified to account for the complex source topography. The software prototype is designed to be used for the Expert Technical Analysis at the IDC. With this, the design effectively reuses the NDC-in-a-Box code and can be comfortably utilized by the NDC users. The package uses Geotool as a front-end for data retrieval and pre-processing. After the event database is compiled, the control is passed to the driver software, running the external processing and plotting toolboxes, which controls the final stage and produces the final result. The modules are mostly Python coded, C-coded (Raysynth3D complex topography regional synthetics) and FORTRAN coded synthetics from the CPS330 software package by Robert Herrmann of Saint Louis University. The extension of this single station depth determination method is under development and uses joint information from all stations participating in processing. It is based on simultaneous depth and moment tensor determination for both short and long period seismic phases. A novel approach recently developed for microseismic event location utilizing only phase waveform information was migrated to a global scale. It should provide faster computation as it does not require intensive synthetic modelling, and might benefit processing noisy signals. A consistent depth estimate for all recent nuclear tests was produced for the vast number of IMS stations (primary and auxiliary) used in processing.

Utilizing a Health Impact Assessment (HIA) to Connect Natural ...

EPA Pesticide Factsheets

Marrying scientific and health research with natural resource management should be a straightforward process. However, differences in purpose, goals, language, levels of detail and implementation authority between the scientists who conduct research and resource managers who plan and implement projects make it difficult for resource managers to include information not specific to the problem at hand. One method to overcome this barrier is a Health Impact Assessment (HIA) or process that uses scientific data, health expertise and public input to factor public health considerations into the decision-making process. An HIA informs decision makers and stakeholders of the potential health effects of a proposed program, policy, project or plan through a systematic investigation of impacts to health and health determinants and deliberative engagement of community members and other stakeholders throughout the HIA process. USEPA will be conducting an HIA on the Minnesota Department of Natural Resources’ sediment remediation and habitat restoration project at Kingsbury Bay and Grassy Point. This poster outlines the HIA process, illustrates how technical and stakeholder committees inform the process, and presents the determinants of health that will be explored in the HIA. This poster will illustrate how a Health Impact Assessment, a process that uses scientific data, health expertise and public input to factor public health considerations into the decision-making proces

Web-Based Requesting and Scheduling Use of Facilities

NASA Technical Reports Server (NTRS)

Yeager, Carolyn M.

2010-01-01

Automated User's Training Operations Facility Utilization Request (AutoFUR) is prototype software that administers a Web-based system for requesting and allocating facilities and equipment for astronaut-training classes in conjunction with scheduling the classes. AutoFUR also has potential for similar use in such applications as scheduling flight-simulation equipment and instructors in commercial airplane-pilot training, managing preventive- maintenance facilities, and scheduling operating rooms, doctors, nurses, and medical equipment for surgery. Whereas requesting and allocation of facilities was previously a manual process that entailed examination of documents (including paper drawings) from different sources, AutoFUR partly automates the process and makes all of the relevant information available via the requester s computer. By use of AutoFUR, an instructor can fill out a facility-utilization request (FUR) form on line, consult the applicable flight manifest(s) to determine what equipment is needed and where it should be placed in the training facility, reserve the corresponding hardware listed in a training-hardware inventory database, search for alternative hardware if necessary, submit the FUR for processing, and cause paper forms to be printed. Auto-FUR also maintains a searchable archive of prior FURs.

FPGA-Based Front-End Electronics for Positron Emission Tomography

PubMed Central

Haselman, Michael; DeWitt, Don; McDougald, Wendy; Lewellen, Thomas K.; Miyaoka, Robert; Hauck, Scott

2010-01-01

Modern Field Programmable Gate Arrays (FPGAs) are capable of performing complex discrete signal processing algorithms with clock rates above 100MHz. This combined with FPGA’s low expense, ease of use, and selected dedicated hardware make them an ideal technology for a data acquisition system for positron emission tomography (PET) scanners. Our laboratory is producing a high-resolution, small-animal PET scanner that utilizes FPGAs as the core of the front-end electronics. For this next generation scanner, functions that are typically performed in dedicated circuits, or offline, are being migrated to the FPGA. This will not only simplify the electronics, but the features of modern FPGAs can be utilizes to add significant signal processing power to produce higher resolution images. In this paper two such processes, sub-clock rate pulse timing and event localization, will be discussed in detail. We show that timing performed in the FPGA can achieve a resolution that is suitable for small-animal scanners, and will outperform the analog version given a low enough sampling period for the ADC. We will also show that the position of events in the scanner can be determined in real time using a statistical positioning based algorithm. PMID:21961085

Evaluation of results of US corn and soybeans exploratory experiment: Classification procedures verification test. [Missouri, Iowa, Indiana, and Illinois

NASA Technical Reports Server (NTRS)

Carnes, J. G.; Baird, J. E. (Principal Investigator)

1980-01-01

The classification procedure utilized in making crop proportion estimates for corn and soybeans using remotely sensed data was evaluated. The procedure was derived during the transition year of the Large Area Crop Inventory Experiment. Analysis of variance techniques were applied to classifications performed by 3 groups of analysts who processed 25 segments selected from 4 agrophysical units (APU's). Group and APU effects were assessed to determine factors which affected the quality of the classifications. The classification results were studied to determine the effectiveness of the procedure in producing corn and soybeans proportion estimates.

Determination of the viscous acoustic field for liquid drop positioning/forcing in an acoustic levitation chamber in microgravity

NASA Technical Reports Server (NTRS)

Lyell, Margaret J.

1992-01-01

The development of acoustic levitation systems has provided a technology with which to undertake droplet studies as well as do containerless processing experiments in a microgravity environment. Acoustic levitation chambers utilize radiation pressure forces to position/manipulate the drop. Oscillations can be induced via frequency modulation of the acoustic wave, with the modulated acoustic radiation vector acting as the driving force. To account for tangential as well as radial forcing, it is necessary that the viscous effects be included in the acoustic field. The method of composite expansions is employed in the determination of the acoustic field with viscous effects.

RESIDUAL RISK ASSESSMENTS - RESIDUAL RISK ...

EPA Pesticide Factsheets

This source category previously subjected to a technology-based standard will be examined to determine if health or ecological risks are significant enough to warrant further regulation for Coke Ovens. These assesments utilize existing models and data bases to examine the multi-media and multi-pollutant impacts of air toxics emissions on human health and the environment. Details on the assessment process and methodologies can be found in EPA's Residual Risk Report to Congress issued in March of 1999 (see web site). To assess the health risks imposed by air toxics emissions from Coke Ovens to determine if control technology standards previously established are adequately protecting public health.

Integration of utility and environmental activities in the project development process.

DOT National Transportation Integrated Search

2010-01-01

Two sources of delay during the project development process are utility adjustments and the environmental : review and clearance process. There are several efforts underway at the Texas Department of Transportation : (TxDOT) to optimize these process...

Processing Waveform-Based NDE

NASA Technical Reports Server (NTRS)

Roth, Donald J (Inventor)

2011-01-01

A computer implemented process for simultaneously measuring the velocity of terahertz electromagnetic radiation in a dielectric material sample without prior knowledge of the thickness of the sample and for measuring the thickness of a material sample using terahertz electromagnetic radiation in a material sample without prior knowledge of the velocity of the terahertz electromagnetic radiation in the sample is disclosed and claimed. Utilizing interactive software the process evaluates, in a plurality of locations, the sample for microstructural variations and for thickness variations and maps the microstructural and thickness variations by location. A thin sheet of dielectric material may be used on top of the sample to create a dielectric mismatch. The approximate focal point of the radiation source (transceiver) is initially determined for good measurements.

Processing multispectral data obtained by orbital platforms of the LANDSAT series for studies of water quality in Guanabara Bay. M.S. Thesis

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator); Verdesio, J. J.

1981-01-01

The relationship existing between Guanabara Bay water quality ground truth parameters and LANDSAT MSS video data was investigated. The parameters considered were: chorophyll content, water transparency usng the Secchi disk, salinity, and dissolved ammonia. Data from two overflights was used, and methods of processing digital data were compared. Linear and nonlinear regression analyses were utilized, comparing original data with processed data by using the correlation coefficient and the estimation mean error. It was determined that better quality data are obtained by using radiometric correction programs with a physical basis, contrast ratio, and normalization. Incidental locations of floating vegetation, changes in bottom depth, oil slicks, and ships at anchor were made.

Integrated orbit and attitude hardware-in-the-loop simulations for autonomous satellite formation flying

NASA Astrophysics Data System (ADS)

Park, Han-Earl; Park, Sang-Young; Kim, Sung-Woo; Park, Chandeok

2013-12-01

Development and experiment of an integrated orbit and attitude hardware-in-the-loop (HIL) simulator for autonomous satellite formation flying are presented. The integrated simulator system consists of an orbit HIL simulator for orbit determination and control, and an attitude HIL simulator for attitude determination and control. The integrated simulator involves four processes (orbit determination, orbit control, attitude determination, and attitude control), which interact with each other in the same way as actual flight processes do. Orbit determination is conducted by a relative navigation algorithm using double-difference GPS measurements based on the extended Kalman filter (EKF). Orbit control is performed by a state-dependent Riccati equation (SDRE) technique that is utilized as a nonlinear controller for the formation control problem. Attitude is determined from an attitude heading reference system (AHRS) sensor, and a proportional-derivative (PD) feedback controller is used to control the attitude HIL simulator using three momentum wheel assemblies. Integrated orbit and attitude simulations are performed for a formation reconfiguration scenario. By performing the four processes adequately, the desired formation reconfiguration from a baseline of 500-1000 m was achieved with meter-level position error and millimeter-level relative position navigation. This HIL simulation demonstrates the performance of the integrated HIL simulator and the feasibility of the applied algorithms in a real-time environment. Furthermore, the integrated HIL simulator system developed in the current study can be used as a ground-based testing environment to reproduce possible actual satellite formation operations.

Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

List, III, Frederick Alyious; Feuerstein, Albert; Dehoff, Ryan

2016-03-30

The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheetmore » material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture geometry using the EBM technology in order to compare deposition features such as surface roughness, geometric accuracy, deposition rate, surface and subsurface porosity, and material quality. It was determined that the laser powder bed technology was ideal for the geometry and requirements of the fixture set by Praxair, and Praxair moved forward with the purchase of a laser powder bed system. The subsequent portion of the project focused on determining the ideal processing parameters for alloy X for the laser powder bed system using ORNL’s Renishaw laser powder bed system. Praxair supplied gas atomized powders of alloy X material with properties specified by ORNL. ORNL printed text cube arrays in order to determine the ideal combination of laser powder and laser travel speed in order to maximize material density, improve surface quality, and maintain geometric accuracy. Additional powder supplied by Praxair was used to fabricate a full-scale fixture component.« less

Determining and prioritizing competencies in the undergraduate internal medicine curriculum in Saudi Arabia.

PubMed

Almoallim, H

2011-08-01

To determine knowledge and skills competencies in internal medicine for the undergraduate curriculum in Saudi Arabia, competencies were identified based on group work utilizing common textbooks. The Delphi Technique was used as a consensus method to determine and prioritize competencies in internal medicine. A group of 20 clinicians rated the identified competencies from 0-3 (0: no need to know, 1: interesting to know, 2: should know and 3: must know). After formulating the results, a second Delphi round was conducted with 5 experts in internal medicine. A total of 1513 knowledge competencies and 189 skills competencies were determined and prioritized. The competencies corresponded to the 12 systems in internal medicine. All competencies rated 2.2-3.0 were produced separately and considered core competencies for the undergraduate internal medicine curriculum. Determining and prioritizing competencies should influence the curriculum reform process.

Automatic Sleep Stage Determination by Multi-Valued Decision Making Based on Conditional Probability with Optimal Parameters

NASA Astrophysics Data System (ADS)

Wang, Bei; Sugi, Takenao; Wang, Xingyu; Nakamura, Masatoshi

Data for human sleep study may be affected by internal and external influences. The recorded sleep data contains complex and stochastic factors, which increase the difficulties for the computerized sleep stage determination techniques to be applied for clinical practice. The aim of this study is to develop an automatic sleep stage determination system which is optimized for variable sleep data. The main methodology includes two modules: expert knowledge database construction and automatic sleep stage determination. Visual inspection by a qualified clinician is utilized to obtain the probability density function of parameters during the learning process of expert knowledge database construction. Parameter selection is introduced in order to make the algorithm flexible. Automatic sleep stage determination is manipulated based on conditional probability. The result showed close agreement comparing with the visual inspection by clinician. The developed system can meet the customized requirements in hospitals and institutions.

FY13 GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATIONS OF THE DWPF CHEMICAL PROCESS CELL WITH SIMULANTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D.; Zamecnik, J.; Best, D.

Savannah River Remediation is evaluating changes to its current Defense Waste Processing Facility flowsheet to replace formic acid with glycolic acid in order to improve processing cycle times and decrease by approximately 100x the production of hydrogen, a potentially flammable gas. Higher throughput is needed in the Chemical Processing Cell since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the safety significant gas chromatographs and the potential for production of flammable quantities of hydrogen, eliminating the use of formic acid is highly desirable. Previous testing at the Savannah Rivermore » National Laboratory has shown that replacing formic acid with glycolic acid allows the reduction and removal of mercury without significant catalytic hydrogen generation. Five back-to-back Sludge Receipt and Adjustment Tank (SRAT) cycles and four back-to-back Slurry Mix Evaporator (SME) cycles were successful in demonstrating the viability of the nitric/glycolic acid flowsheet. The testing was completed in FY13 to determine the impact of process heels (approximately 25% of the material is left behind after transfers). In addition, back-to-back experiments might identify longer-term processing problems. The testing was designed to be prototypic by including sludge simulant, Actinide Removal Product simulant, nitric acid, glycolic acid, and Strip Effluent simulant containing Next Generation Solvent in the SRAT processing and SRAT product simulant, decontamination frit slurry, and process frit slurry in the SME processing. A heel was produced in the first cycle and each subsequent cycle utilized the remaining heel from the previous cycle. Lower SRAT purges were utilized due to the low hydrogen generation. Design basis addition rates and boilup rates were used so the processing time was shorter than current processing rates.« less

Additive Manufacturing of Porous Metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dehoff, Ryan R.; Kirka, Michael M.

2017-06-01

Currently, helium is obtained through separation from natural gas. The current industrial process incurs significant costs and requires large energy resources to successfully achieve separation. Through utilizing Additive Manufacturing (AM) technologies it is possible to reduce both of these burdens when refining helium gas. The ability to engineer porosity levels within Inconel 718 discs for controlled separation of helium from natural gas was investigated. Arrays of samples fabricated using the electron beam melting process were analyzed for their relative porosity density. Based upon the measurements, full scale discs were fabricated, and subsequently tested to determine their effectiveness in separating heliummore » from liquefied natural gas.« less

Simulation of the effect of incline incident angle in DMD Maskless Lithography

NASA Astrophysics Data System (ADS)

Liang, L. W.; Zhou, J. Y.; Xiang, L. L.; Wang, B.; Wen, K. H.; Lei, L.

2017-06-01

The aim of this study is to provide a simulation method for investigation of the intensity fluctuation caused by the inclined incident angle in DMD (digital micromirror device) maskless lithography. The simulation consists of eight main processes involving the simplification of the DMD aperture function and light propagation utilizing the non-parallel angular spectrum method. These processes provide a possibility of co-simulation in the spatial frequency domain, which combines the microlens array and DMD in the maskless lithography system. The simulation provided the spot shape and illumination distribution. These two parameters are crucial in determining the exposure dose in the existing maskless lithography system.

To Meet or Not To Meet Physical vs. Virtual Configuration Control Board

NASA Technical Reports Server (NTRS)

Rice, Shelley

2017-01-01

This presentation will define the CCB, discuss its functions and members. We will look into traditional processes of managing change control via the CCB meeting and advanced practices utilizing enhanced product tools and technologies. Well step through a summary of the feedback from the community of CM professionals at NASA Goddard Space Flight Center of best practices as well as pros and cons for facilitating both a physical CCB and managing stakeholder approvals in a virtual environment. Attendees will come away with current industry strategies to determine if process for managing change control and approvals can be streamlined within their local work environments.

Microscopy basics and the study of actin-actin-binding protein interactions.

PubMed

Thomasson, Maggie S; Macnaughtan, Megan A

2013-12-15

Actin is a multifunctional eukaryotic protein with a globular monomer form that polymerizes into a thin, linear microfilament in cells. Through interactions with various actin-binding proteins (ABPs), actin plays an active role in many cellular processes, such as cell motility and structure. Microscopy techniques are powerful tools for determining the role and mechanism of actin-ABP interactions in these processes. In this article, we describe the basic concepts of fluorescent speckle microscopy, total internal reflection fluorescence microscopy, atomic force microscopy, and cryoelectron microscopy and review recent studies that utilize these techniques to visualize the binding of actin with ABPs. Copyright © 2013 Elsevier Inc. All rights reserved.

Satellite orbit determination from an airborne platform

NASA Astrophysics Data System (ADS)

Shepard, M. M.; Foshee, J. J.

This paper describes the requirements, approach, and problems associated with autonomous satellite orbit determination from an airborne platform. The ability to perform orbit determination from an airborne platform removes the reliance on ground control facilities. Aircraft orbit determination offers a more robust system in that it is less susceptible to direct attack, sabotage, or nuclear disaster. Ranging on a satellite and the processing of range/range-rate data along with INS inputs to produce a set of orbital parameters to be transmitted to user terminals are discussed. Several algorithms that could be utilized by the user terminal to recover the satellite position/velocity data from the transmitted message are presented. The ability to compress the ephemeris message to a small size while remaining autonomous for a long period of time, as would be needed in future military communication satellites, is discussed.

An intervention to improve the catheter associated urinary tract infection rate in a medical intensive care unit: Direct observation of catheter insertion procedure.

PubMed

Galiczewski, Janet M; Shurpin, Kathleen M

2017-06-01

Healthcare associated infections from indwelling urinary catheters lead to increased patient morbidity and mortality. The purpose of this study was to determine if direct observation of the urinary catheter insertion procedure, as compared to the standard process, decreased catheter utilization and urinary tract infection rates. This case control study was conducted in a medical intensive care unit. During phase I, a retrospective data review was conducted on utilsiation and urinary catheter infection rates when practitioners followed the institution's standard insertion algorithm. During phase II, an intervention of direct observation was added to the standard insertion procedure. The results demonstrated no change in utilization rates, however, CAUTI rates decreased from 2.24 to 0 per 1000 catheter days. The findings from this study may promote changes in clinical practice guidelines leading to a reduction in urinary catheter utilization and infection rates and improved patient outcomes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Using Multicriteria Analysis in Issues Concerning Adaptation of Historic Facilities for the Needs of Public Utility Buildings with a Function of a Theatre

NASA Astrophysics Data System (ADS)

Obracaj, Piotr; Fabianowski, Dariusz

2017-10-01

Implementations concerning adaptation of historic facilities for public utility objects are associated with the necessity of solving many complex, often conflicting expectations of future users. This mainly concerns the function that includes construction, technology and aesthetic issues. The list of issues is completed with proper protection of historic values, different in each case. The procedure leading to obtaining the expected solution is a multicriteria procedure, usually difficult to accurately define and requiring designer’s large experience. An innovative approach has been used for the analysis, namely - the modified EA FAHP (Extent Analysis Fuzzy Analytic Hierarchy Process) Chang’s method of a multicriteria analysis for the assessment of complex functional and spatial issues. Selection of optimal spatial form of an adapted historic building intended for the multi-functional public utility facility was analysed. The assumed functional flexibility was determined in the scope of: education, conference, and chamber spectacles, such as drama, concerts, in different stage-audience layouts.

Modeling of Depth Cue Integration in Manual Control Tasks

NASA Technical Reports Server (NTRS)

Sweet, Barbara T.; Kaiser, Mary K.; Davis, Wendy

2003-01-01

Psychophysical research has demonstrated that human observers utilize a variety of visual cues to form a perception of three-dimensional depth. However, most of these studies have utilized a passive judgement paradigm, and failed to consider depth-cue integration as a dynamic and task-specific process. In the current study, we developed and experimentally validated a model of manual control of depth that examines how two potential cues (stereo disparity and relative size) are utilized in both first- and second-order active depth control tasks. We found that stereo disparity plays the dominate role for determining depth position, while relative size dominates perception of depth velocity. Stereo disparity also plays a reduced role when made less salient (i.e., when viewing distance is increased). Manual control models predict that position information is sufficient for first-order control tasks, while velocity information is required to perform a second-order control task. Thus, the rules for depth-cue integration in active control tasks are dependent on both task demands and cue quality.

Development of a nucleotide sugar purification method using a mixed mode column & mass spectrometry detection.

PubMed

Eastwood, Heather; Xia, Fang; Lo, Mei-Chu; Zhou, Jing; Jordan, John B; McCarter, John; Barnhart, Wesley W; Gahm, Kyung-Hyun

2015-11-10

Analysis of nucleotide sugars, nucleoside di- and triphosphates and sugar-phosphates is an essential step in the process of understanding enzymatic pathways. A facile and rapid separation method was developed to analyze these compounds present in an enzymatic reaction mixture utilized to produce nucleotide sugars. The Primesep SB column explored in this study utilizes hydrophobic interactions as well as electrostatic interactions with the phosphoric portion of the nucleotide sugars. Ammonium formate buffer was selected due to its compatibility with mass spectrometry. Negative ion mode mass spectrometry was adopted for detection of the sugar phosphate (fucose-1-phophate), as the compound is not amenable to UV detection. Various mobile phase conditions such as pH, buffer concentration and organic modifier were explored. The semi-preparative separation method was developed to prepare 30mg of the nucleotide sugar. (19)F NMR was utilized to determine purity of the purified fluorinated nucleotide sugar. The collected nucleotide sugar was found to be 99% pure. Published by Elsevier B.V.

Principle and Performance of Gas Self-inducing Reactors and Applications to Biotechnology.

PubMed

Ye, Qin; Li, Zhimin; Wu, Hui

2016-01-01

Gas-liquid contacting is an important unit operation in chemical and biochemical processes, but the gas utilization efficiency is low in conventional gas-liquid contactors especially for sparingly soluble gases. The gas self-inducing impeller is able to recycle gas in the headspace of a reactor to the liquid without utilization of additional equipment such as a gas compressor, and thus, the gas utilization efficiency is significantly enhanced. Gas induction is caused by the low pressure or deep vortex at a sufficiently high impeller speed, and the speed at which gas induction starts is termed the critical speed. The critical impeller speed, gas-induction flow rate, power consumption, and gas-liquid mass transfer are determined by the impeller design and operation conditions. When the reactor is operated in a dead-end mode, all the introduced gas can be completely used, and this feature is especially favorable to flammable and/or toxic gases. In this article, the principles, designs, characteristics of self-inducing reactors, and applications to biotechnology are described.

Load Forecasting in Electric Utility Integrated Resource Planning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvallo, Juan Pablo; Larsen, Peter H.; Sanstad, Alan H

Integrated resource planning (IRP) is a process used by many vertically-integrated U.S. electric utilities to determine least-cost/risk supply and demand-side resources that meet government policy objectives and future obligations to customers and, in many cases, shareholders. Forecasts of energy and peak demand are a critical component of the IRP process. There have been few, if any, quantitative studies of IRP long-run (planning horizons of two decades) load forecast performance and its relationship to resource planning and actual procurement decisions. In this paper, we evaluate load forecasting methods, assumptions, and outcomes for 12 Western U.S. utilities by examining and comparing plansmore » filed in the early 2000s against recent plans, up to year 2014. We find a convergence in the methods and data sources used. We also find that forecasts in more recent IRPs generally took account of new information, but that there continued to be a systematic over-estimation of load growth rates during the period studied. We compare planned and procured resource expansion against customer load and year-to-year load growth rates, but do not find a direct relationship. Load sensitivities performed in resource plans do not appear to be related to later procurement strategies even in the presence of large forecast errors. These findings suggest that resource procurement decisions may be driven by other factors than customer load growth. Our results have important implications for the integrated resource planning process, namely that load forecast accuracy may not be as important for resource procurement as is generally believed, that load forecast sensitivities could be used to improve the procurement process, and that management of load uncertainty should be prioritized over more complex forecasting techniques.« less

Improvements in the efficiency of turboexpanders in cryogenic applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agahi, R.R.; Lin, M.C.; Ershaghi, B.

1996-12-31

Process designers have utilized turboexpanders in cryogenic processes because of their higher thermal efficiencies when compared with conventional refrigeration cycles. Process design and equipment performance have improved substantially through the utilization of modern technologies. Turboexpander manufacturers have also adopted Computational Fluid Dynamic Software, Computer Numerical Control Technology and Holography Techniques to further improve an already impressive turboexpander efficiency performance. In this paper, the authors explain the design process of the turboexpander utilizing modern technology. Two cases of turboexpanders processing helium (4.35{degrees}K) and hydrogen (56{degrees}K) will be presented.

Green Pea and Garlic Puree Model Food Development for Thermal Pasteurization Process Quality Evaluation.

PubMed

Bornhorst, Ellen R; Tang, Juming; Sablani, Shyam S; Barbosa-Cánovas, Gustavo V; Liu, Fang

2017-07-01

Development and selection of model foods is a critical part of microwave thermal process development, simulation validation, and optimization. Previously developed model foods for pasteurization process evaluation utilized Maillard reaction products as the time-temperature integrators, which resulted in similar temperature sensitivity among the models. The aim of this research was to develop additional model foods based on different time-temperature integrators, determine their dielectric properties and color change kinetics, and validate the optimal model food in hot water and microwave-assisted pasteurization processes. Color, quantified using a * value, was selected as the time-temperature indicator for green pea and garlic puree model foods. Results showed 915 MHz microwaves had a greater penetration depth into the green pea model food than the garlic. a * value reaction rates for the green pea model were approximately 4 times slower than in the garlic model food; slower reaction rates were preferred for the application of model food in this study, that is quality evaluation for a target process of 90 °C for 10 min at the cold spot. Pasteurization validation used the green pea model food and results showed that there were quantifiable differences between the color of the unheated control, hot water pasteurization, and microwave-assisted thermal pasteurization system. Both model foods developed in this research could be utilized for quality assessment and optimization of various thermal pasteurization processes. © 2017 Institute of Food Technologists®.

Coal liquefaction process solvent characterization and evaluation: Progress report, 1 April--30 June 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winschel, R. A.; Robbins, G. A.; Burke, F. P.

1986-11-01

Conoco Coal Research Division is characterizing samples of direct coal liquefaction process oils based on a variety of analytical techniques to provide a detailed description of the chemical composition of the oils to more fully understand the interrelationship of process oil composition and process operations, to aid in plant operation, and to lead to process improvements. The approach taken is to obtain analyses of a large number of well-defined process oils taken during periods of known operating conditions and known process performance. A set of thirty-one process oils from the Hydrocarbon Research, Inc. (HRI) Catalytic Two-Stage Liquefaction (CTSL) bench unitmore » was analyzed to provide information on process performance. The Fourier-Transform infrared (FTIR) spectroscopic method for the determination of phenolics in cola liquids was further verified. A set of four tetahydrofuran-soluble products from Purdue Research Foundation's reactions of coal/potassium/crown ether, analyzed by GC/MS and FTIR, were found to consist primarily of paraffins (excluding contaminants). Characterization data (elemental analyses, /sup 1/H-NMR and phenolic concentrations) were obtained on a set of twenty-seven two-stage liquefaction oils. Two activities were begun but not completed. First, analyses were started on oils from Wilsonville Run 250 (close- coupled ITSL). Also, a carbon isotopic method is being examined for utility in determining the relative proportion of coal and petroleum products in coprocessing oils.« less

Review: Milking robot utilization, a successful precision livestock farming evolution.

PubMed

John, A J; Clark, C E F; Freeman, M J; Kerrisk, K L; Garcia, S C; Halachmi, I

2016-09-01

Automatic milking systems (AMS), one of the earliest precision livestock farming developments, have revolutionized dairy farming around the world. While robots control the milking process, there have also been numerous changes to how the whole farm system is managed. Milking is no longer performed in defined sessions; rather, the cow can now choose when to be milked in AMS, allowing milking to be distributed throughout a 24 h period. Despite this ability, there has been little attention given to milking robot utilization across 24 h. In order to formulate relevant research questions and improve farm AMS management there is a need to determine the current knowledge gaps regarding the distribution of robot utilization. Feed, animal and management factors and their interplay on levels of milking robot utilization across 24 h for both indoor and pasture-based systems are here reviewed. The impact of the timing, type and quantity of feed offered and their interaction with the distance of feed from the parlour; herd social dynamics, climate and various other management factors on robot utilization through 24 h are provided. This novel review draws together both the opportunities and challenges that exist for farm management to use these factors to improved system efficiency and those that exist for further research.

Biomarkers for Early Detection of Clinically Relevant Prostate Cancer. A Multi-Institutional Validation Trial

DTIC Science & Technology

2016-10-01

Study (PASS). We are in the process of evaluating these three biomarker panels in tissue, blood, and urine samples with well annotated clinical and...impacting both the initial choice of therapy and decision-making during AS. The objective of the study is to utilize analytically validated assays that...predict reclassification from Gleason 6 cancer to Gleason 7 or greater. The analysis plan was determined before specimens were selected for the study

Biomarkers for Early Detection of Clinically Relevant Prostate Cancer. A Multi-Institutional Validation Trial

DTIC Science & Technology

2016-10-01

Study (PASS). We are in the process of evaluating these three biomarker panels in tissue, blood, and urine samples with well annotated clinical and...choice of therapy and decision-making during AS. The objective of the study is to utilize analytically validated assays that take into account tumor...Gleason 6 cancer to Gleason 7 or greater. The analysis plan was determined before specimens were selected for the study , and included 7 breaking

Improving client and nurse satisfaction through the utilization of bedside report.

PubMed

Vines, Mary M; Dupler, Alice E; Van Son, Catherine R; Guido, Ginny W

2014-01-01

Bedside reporting improves client safety and trust and facilitates nursing teamwork and accountability; however, many nurses do not consider it best practice when caring for their clients. A literature review was conducted to determine whether bedside report is an essential shift handover process that promotes both client and nursing satisfaction. Implications for nurses in professional development are discussed, and strategies for developing and implementing bedside report using Lewin's theory of planned change are provided.

Producing Zirconium Diboride Components with Complex, Near-Net Shape Geometries by Aqueous Room-Temperature Injection Molding

NASA Technical Reports Server (NTRS)

Wiesner, Valerie L.; Youngblood, Jeffrey; Trice, Rodney

2014-01-01

Room-temperature injection molding is proposed as a novel, low-cost and more energy efficient manufacturing process capable of forming complex-shaped zirconium diboride (ZrB2) parts. This innovative processing method utilized aqueous suspensions with high powder loading and a minimal amount (5 vol.) of water-soluble polyvinylpyrrolidone (PVP), which was used as a viscosity modifier. Rheological characterization was performed to evaluate the room-temperature flow properties of ZrB2-PVP suspensions. ZrB2 specimens were fabricated with high green body strength and were machinable prior to binder removal despite their low polymer content. After binder burnout and pressureless sintering, the bulk density and microstructure of specimens were characterized using Archimedes technique and scanning electron microscopy. X-Ray Diffraction was used to determine the phase compositions present in sintered specimens. Ultimate strength of sintered specimens will be determined using ASTM C1323-10 compressive C-ring test.

Quantifying Grain Level Stress-Strain Behavior for AM40 via Instrumented Microindentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Guang; Barker, Erin I.; Stephens, Elizabeth V.

2016-01-01

ABSTRACT Microindentation is performed on hot isostatic pressed (HIP) Mg-Al (AM40) alloy samples produced by high-pressure die cast (HPDC) process for the purpose of quantifying the mechanical properties of the α-Mg grains. The process of obtaining elastic modulus and hardness from indentation load-depth curves is well established in the literature. A new inverse method is developed to extract plastic properties in this study. The method utilizes empirical yield strength-hardness relationship reported in the literature together with finite element modeling of the individual indentation. Due to the shallow depth of the indentation, indentation size effect (ISE) is taken into account whenmore » determining plastic properties. The stress versus strain behavior is determined for a series of indents. The resulting average values and standard deviations are obtained for future use as input distributions for microstructure-based property prediction of AM40.« less

Political dynamics determined by interactions between political leaders and voters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernard, Michael Lewis; Bier, Asmeret; Backus, George A.

2010-03-01

The political dynamics associated with an election are typically a function of the interplay between political leaders and voters, as well as endogenous and exogenous factors that impact the perceptions and goals of the electorate. This paper describes an effort by Sandia National Laboratories to model the attitudes and behaviors of various political groups along with that population's primary influencers, such as government leaders. To accomplish this, Sandia National Laboratories is creating a hybrid system dynamics-cognitive model to simulate systems- and individual-level political dynamics in a hypothetical society. The model is based on well-established psychological theory, applied to both individualsmore » and groups within the modeled society. Confidence management processes are being incorporated into the model design process to increase the utility of the tool and assess its performance. This project will enhance understanding of how political dynamics are determined in democratic society.« less

Designing food delivery systems: challenges related to the in vitro methods employed to determine the fate of bioactives in the gut.

PubMed

Arranz, Elena; Corredig, Milena; Guri, Anilda

2016-08-10

An in depth understanding of the underpinning mechanisms that relate to food disruption and processing in the gastrointestinal tract is necessary to achieve optimal intake of nutrients and their bioefficacy. Although in vivo trials can provide insights on physiological responses of nutrients, in vitro assays are often applied as tools to understand specific mechanisms, or as prescreening methods to determine the factors associated with the uptake of food components in the gastrointestinal tract. In vitro assays are also often utilized to design novel or improved food delivery systems. In this review the available approaches to study delivery and uptake of food bioactives and the associated challenges are discussed. For an in depth understanding of food processing in the gastrointestinal tract, it is necessary to apply multidisciplinary methodologies, at the interface between materials science, chemistry, physics and biology.

Noncoherent Tracking of a Source of a Data-Modulated Signal

NASA Technical Reports Server (NTRS)

Arndt, G. Dickey; Ngo, Phong; Chen, Henry; Phan, Chau T.; Hill, Brent; Bourgeois, Brian; Dusl, John

2003-01-01

A proposed tracking receiver system containing three suitably positioned antenna elements and special signal-processing equipment would determine the direction of incidence of a microwave signal containing spread-spectrum digital data modulation. If the system were to contain two sets of antenna elements separated by a known baseline, it could determine the location of the transmitter as the intersection of the lines of incidence on the two antennas. Such systems could be used for diverse purposes in outer space and on Earth, including tracking astronauts and small robotic spacecraft working outside a spacecraft or space station, and locating cellular telephones from which distress calls have been made. The principle of operation does not require the transmission of a special identifying or distress signal by the cellular telephone or other transmitter to be tracked; instead, the system could utilize the data signal routinely sent by the transmitter, provided that the signal had the characteristics needed for processing.

Understanding error generation in fused deposition modeling

NASA Astrophysics Data System (ADS)

Bochmann, Lennart; Bayley, Cindy; Helu, Moneer; Transchel, Robert; Wegener, Konrad; Dornfeld, David

2015-03-01

Additive manufacturing offers completely new possibilities for the manufacturing of parts. The advantages of flexibility and convenience of additive manufacturing have had a significant impact on many industries, and optimizing part quality is crucial for expanding its utilization. This research aims to determine the sources of imprecision in fused deposition modeling (FDM). Process errors in terms of surface quality, accuracy and precision are identified and quantified, and an error-budget approach is used to characterize errors of the machine tool. It was determined that accuracy and precision in the y direction (0.08-0.30 mm) are generally greater than in the x direction (0.12-0.62 mm) and the z direction (0.21-0.57 mm). Furthermore, accuracy and precision tend to decrease at increasing axis positions. The results of this work can be used to identify possible process improvements in the design and control of FDM technology.

Research on a Defects Detection Method in the Ferrite Phase Shifter Cementing Process Based on a Multi-Sensor Prognostic and Health Management (PHM) System.

PubMed

Wan, Bo; Fu, Guicui; Li, Yanruoyue; Zhao, Youhu

2016-08-10

The cementing manufacturing process of ferrite phase shifters has the defect that cementing strength is insufficient and fractures always appear. A detection method of these defects was studied utilizing the multi-sensors Prognostic and Health Management (PHM) theory. Aiming at these process defects, the reasons that lead to defects are analyzed in this paper. In the meanwhile, the key process parameters were determined and Differential Scanning Calorimetry (DSC) tests during the cure process of resin cementing were carried out. At the same time, in order to get data on changing cementing strength, multiple-group cementing process tests of different key process parameters were designed and conducted. A relational model of cementing strength and cure temperature, time and pressure was established, by combining data of DSC and process tests as well as based on the Avrami formula. Through sensitivity analysis for three process parameters, the on-line detection decision criterion and the process parameters which have obvious impact on cementing strength were determined. A PHM system with multiple temperature and pressure sensors was established on this basis, and then, on-line detection, diagnosis and control for ferrite phase shifter cementing process defects were realized. It was verified by subsequent process that the on-line detection system improved the reliability of the ferrite phase shifter cementing process and reduced the incidence of insufficient cementing strength defects.

A Facile CD Protocol for Rapid Determination of Enantiomeric Excess and Concentration of Chiral Primary Amines

PubMed Central

Nieto, Sonia; Dragna, Justin M.; Anslyn, Eric V.

2010-01-01

A protocol for the rapid determination of the absolute configuration and enantiomeric excess of α-chiral primary amines with potential applications in asymmetric reaction discovery has been developed. The protocol requires derivatization of α-chiral primary amines via condensation with pyridine carboxaldehyde to quantitatively yield the corresponding imine. The Cu(I) complex with 2,2'-bis (diphenylphosphino)-1,1'-dinaphthyl (BINAP -CuI) with the imine yields a metal-to-ligand-charge-transfer band (MLCT) in the visible region of the circular dichroism spectrum upon binding. Diastereomeric host-guest complexes give CD signals of the same signs, but different amplitudes, allowing for differentiation of enantiomers. Processing the primary optical data from the CD spectrum with linear discriminant analysis (LDA) allows for the determination of absolute configuration and identification of the amines, and processing with a supervised multi-layer perceptron artifical neural network (MLP-ANN) allows for the simultaneous determination of ee and concentration. The primary optical data necessary to determine the ee of unknown samples is obtained in 2 minutes per sample. To demonstrate the utility of the protocol in asymmetric reaction discovery, the ee's and concentrations for an asymmetric metal catalyzed reaction are determined. The potential of the protocol's application in high-throughput screening (HTS) of ee is discussed. PMID:19946914

Structured decision making as a conceptual framework to identify thresholds for conservation and management

USGS Publications Warehouse

Martin, J.; Runge, M.C.; Nichols, J.D.; Lubow, B.C.; Kendall, W.L.

2009-01-01

Thresholds and their relevance to conservation have become a major topic of discussion in the ecological literature. Unfortunately, in many cases the lack of a clear conceptual framework for thinking about thresholds may have led to confusion in attempts to apply the concept of thresholds to conservation decisions. Here, we advocate a framework for thinking about thresholds in terms of a structured decision making process. The purpose of this framework is to promote a logical and transparent process for making informed decisions for conservation. Specification of such a framework leads naturally to consideration of definitions and roles of different kinds of thresholds in the process. We distinguish among three categories of thresholds. Ecological thresholds are values of system state variables at which small changes bring about substantial changes in system dynamics. Utility thresholds are components of management objectives (determined by human values) and are values of state or performance variables at which small changes yield substantial changes in the value of the management outcome. Decision thresholds are values of system state variables at which small changes prompt changes in management actions in order to reach specified management objectives. The approach that we present focuses directly on the objectives of management, with an aim to providing decisions that are optimal with respect to those objectives. This approach clearly distinguishes the components of the decision process that are inherently subjective (management objectives, potential management actions) from those that are more objective (system models, estimates of system state). Optimization based on these components then leads to decision matrices specifying optimal actions to be taken at various values of system state variables. Values of state variables separating different actions in such matrices are viewed as decision thresholds. Utility thresholds are included in the objectives component, and ecological thresholds may be embedded in models projecting consequences of management actions. Decision thresholds are determined by the above-listed components of a structured decision process. These components may themselves vary over time, inducing variation in the decision thresholds inherited from them. These dynamic decision thresholds can then be determined using adaptive management. We provide numerical examples (that are based on patch occupancy models) of structured decision processes that include all three kinds of thresholds. ?? 2009 by the Ecological Society of America.

An Economic Approach to Setting Contribution Limits in Qualified State-Sponsored Tuition Savings Plans.

ERIC Educational Resources Information Center

Ma, Jennifer; Warshawsky, Mark J.; Ameriks, John; Blohm, Julia A.

This study used an expected utility framework with a mean-lower partial moment specification for investor utility to determine the asset allocation and the allowable contribution limits for qualified state-sponsored tuition savings plans. Given the assumptions about state policymakers' perceptions of investor utility, the study determined the…

Optimized model tuning in medical systems.

PubMed

Kléma, Jirí; Kubalík, Jirí; Lhotská, Lenka

2005-12-01

In medical systems it is often advantageous to utilize specific problem situations (cases) in addition to or instead of a general model. Decisions are then based on relevant past cases retrieved from a case memory. The reliability of such decisions depends directly on the ability to identify cases of practical relevance to the current situation. This paper discusses issues of automated tuning in order to obtain a proper definition of mutual case similarity in a specific medical domain. The main focus is on a reasonably time-consuming optimization of the parameters that determine case retrieval and further utilization in decision making/ prediction. The two case studies - mortality prediction after cardiological intervention, and resource allocation at a spa - document that the optimization process is influenced by various characteristics of the problem domain.

The role of ERTS in the establishment and of a nationwide land cover information system

NASA Technical Reports Server (NTRS)

Abram, P.; Tullos, J.

1974-01-01

The economic potential of utilizing an ERTS type satellite in the development, updating, and maintenance of a nation-wide land cover information system in the post-1977 time frame was examined. Several alternative acquisition systems were evaluated for land cover data acquisition, processing, and interpretation costs in order to determine, on a total life cycle cost basis, under which conditions of user demand (i.e., area of coverage, frequency of coverage, timeliness of information, and level of information detail) an ERTS type satellite would be cost effective, and what the annual cost savings benefits would be. It was concluded that a three satellite system with high and low altitude aircraft and ground survey team utilizing automatic interpretation and classification techniques is an economically sound proposal.

Image based automatic water meter reader

NASA Astrophysics Data System (ADS)

Jawas, N.; Indrianto

2018-01-01

Water meter is used as a tool to calculate water consumption. This tool works by utilizing water flow and shows the calculation result with mechanical digit counter. Practically, in everyday use, an operator will manually check the digit counter periodically. The Operator makes logs of the number shows by water meter to know the water consumption. This manual operation is time consuming and prone to human error. Therefore, in this paper we propose an automatic water meter digit reader from digital image. The digits sequence is detected by utilizing contour information of the water meter front panel.. Then an OCR method is used to get the each digit character. The digit sequence detection is an important part of overall process. It determines the success of overall system. The result shows promising results especially in sequence detection.

Technology transfer to a developing nation, Korea

NASA Technical Reports Server (NTRS)

Stone, C. A.; Uccetta, S. J.

1973-01-01

An experimental project is reported which was undertaken. to determine if selected types of technology developed for the aerospace program during the past decade are relevant to specific industrial problems of a developing nation and to test whether a structured program could facilitate the transfer of relevant technologies. The Korea Institute of Science and Technology and the IIT Research Institute were selected as the active transfer agents to participate in the program. The pilot project was based upon the approach to the transfer of domestic technology developed by the NASA Technology Utilization Division and utilized the extensive data and technical resources available through the Space Agency and its contractors. This pilot project has helped to clarify some aspects of the international technology transfer process and to upgrade Korean technological capabilities.

Electrical transport in AZO nanorods

NASA Astrophysics Data System (ADS)

Yildiz, A.; Cansizoglu, H.; Karabacak, T.

2015-10-01

Al-doped ZnO (AZO) nanorods (NRs) with different lengths were deposited by utilizing glancing angle deposition (GLAD) technique in a DC sputter system at room temperature. The structural and optical characteristics of the NRs were investigated by the X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-vis-NIR spectroscopy measurements. A band gap of about 3.5 eV was observed for the NRs. A novel capping process utilizing varying deposition angles was used to introduce a blanket metal top contact for the electrical characterization of NRs. Current-voltage (I-V) measurements were used to properly evaluate the approximate resistivity of a single NR. The electrical conduction was found to be governed by the thermally activated transport mechanism. Activation energy was determined as 0.14 eV from temperature dependent resistivity data.

Sensing with Superconducting Point Contacts

PubMed Central

Nurbawono, Argo; Zhang, Chun

2012-01-01

Superconducting point contacts have been used for measuring magnetic polarizations, identifying magnetic impurities, electronic structures, and even the vibrational modes of small molecules. Due to intrinsically small energy scale in the subgap structures of the supercurrent determined by the size of the superconducting energy gap, superconductors provide ultrahigh sensitivities for high resolution spectroscopies. The so-called Andreev reflection process between normal metal and superconductor carries complex and rich information which can be utilized as powerful sensor when fully exploited. In this review, we would discuss recent experimental and theoretical developments in the supercurrent transport through superconducting point contacts and their relevance to sensing applications, and we would highlight their current issues and potentials. A true utilization of the method based on Andreev reflection analysis opens up possibilities for a new class of ultrasensitive sensors. PMID:22778630

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tooker, Brian C.; Brindley, Stephen M.; Chiarappa-Zucca, Marina L.

We report that exposure to small amounts of beryllium (Be) can result in beryllium sensitization and progression to Chronic Beryllium Disease (CBD). In CBD, beryllium is presented to Be-responsive T-cells by professional antigen-presenting cells (APC). This presentation drives T-cell proliferation and pro-inflammatory cytokine (IL-2, TNFα, and IFNγ) production and leads to granuloma formation. The mechanism by which beryllium enters an APC and is processed to become part of the beryllium antigen complex has not yet been elucidated. Developing techniques for beryllium detection with enough sensitivity has presented a barrier to further investigation. The objective of this study was to demonstratemore » that Accelerator Mass Spectrometry (AMS) is sensitive enough to quantify the amount of beryllium presented by APC to stimulate Be-responsive T-cells. To achieve this goal, APC - which may or may not stimulate Be-responsive T-cells - were cultured with Be-ferritin. Then, by utilizing AMS, the amount of beryllium processed for presentation was determined. Further, IFNγ intracellular cytokine assays were performed to demonstrate that Be-ferritin (at levels used in the experiments) could stimulate Be-responsive T-cells when presented by an APC of the correct HLA type (HLA-DP0201). The results indicated that Be-responsive T-cells expressed IFNγ only when APC with the correct HLA type were able to process Be for presentation. Utilizing AMS, we determined that APC with HLA-DP0201 had membrane fractions containing 0.17-0.59 ng Be and APC with HLA-DP0401 had membrane fractions bearing 0.40-0.45 ng Be. However, HLA-DP0401 APC had 20-times more Be associated with the whole cells (57.68-61.12 ng) then HLA-DP0201 APC (0.90-3.49 ng). As these findings demonstrate, AMS detection of picogram levels of Be processed by APC is possible. Further, regardless of form, Be requires processing by APC to successfully stimulate Be-responsive T-cells to generate IFNγ.« less

Overcoming Communication Restrictions in Collectives

NASA Technical Reports Server (NTRS)

Tumer, Kagan; Agogino, Adrian K.

2004-01-01

Many large distributed system are characterized by having a large number of components (eg., agents, neurons) whose actions and interactions determine a %orld utility which rates the performance of the overall system. Such collectives are often subject to communication restrictions, making it difficult for components which try to optimize their own private utilities, to take actions that also help optimize the world utility. In this article we address that coordination problem and derive four utility functions which present different compromises between how aligned a component s private utility is with the world utility and how readily that component can determine the actions that optimize its utility. The results show that the utility functions specifically derived to operate under communication restrictions outperform both traditional methods and previous collective-based methods by up to 75%.

Real-time model-based vision system for object acquisition and tracking

NASA Technical Reports Server (NTRS)

Wilcox, Brian; Gennery, Donald B.; Bon, Bruce; Litwin, Todd

1987-01-01

A machine vision system is described which is designed to acquire and track polyhedral objects moving and rotating in space by means of two or more cameras, programmable image-processing hardware, and a general-purpose computer for high-level functions. The image-processing hardware is capable of performing a large variety of operations on images and on image-like arrays of data. Acquisition utilizes image locations and velocities of the features extracted by the image-processing hardware to determine the three-dimensional position, orientation, velocity, and angular velocity of the object. Tracking correlates edges detected in the current image with edge locations predicted from an internal model of the object and its motion, continually updating velocity information to predict where edges should appear in future frames. With some 10 frames processed per second, real-time tracking is possible.

Determinants of psychology service utilization in a palliative care outpatient population.

PubMed

Azuero, Casey; Allen, Rebecca Sue; Kvale, Elizabeth; Azuero, Andres; Parmelee, Patricia

2014-06-01

Research has demonstrated that treating cancer patients' psychological and physical health leads to improved overall health. This may be especially true for palliative care patients facing serious illness. This study examines the proportion and determinants of psychology service utilization in an outpatient palliative care population. Data from an existing clinical database in an outpatient palliative clinic utilizing a collaborative care model to deliver psychology services were explored. This study was framed by Andersen's Behavioral Model of Health Service Use, which incorporates three main components: predisposing, enabling, and need factors to model health service utilization. The sample (N = 149) was majority middle aged, female, and White with a primary diagnosis of cancer. Cross-tabulations were conducted to determine how many patients who met screening criteria for depression or anxiety sought psychology services. Logistic regression analyses were conducted to assess for predisposing, enabling, and need factor determinants of psychology service utilization. Among patients who met criteria for moderate depression or anxiety, 50% did not access readily available psychology services. Enabling factors were the strongest determinant of psychology utilization. Factors associated with need for psychology services (i.e., emotional distress and psychological symptom burden) did not reach significance in determining psychology service use. This study extends current knowledge about psychology utilization to palliative care outpatients receiving care within a collaborative care model. Directions for future research include further investigation of care models that optimize enabling strategies to enhance access to these services, and examination of patient-reported barriers to receiving this care. Copyright © 2013 John Wiley & Sons, Ltd.

Accounting utility for determining individual usage of production level software systems

NASA Technical Reports Server (NTRS)

Garber, S. C.

1984-01-01

An accounting package was developed which determines the computer resources utilized by a user during the execution of a particular program and updates a file containing accumulated resource totals. The accounting package is divided into two separate programs. The first program determines the total amount of computer resources utilized by a user during the execution of a particular program. The second program uses these totals to update a file containing accumulated totals of computer resources utilized by a user for a particular program. This package is useful to those persons who have several other users continually accessing and running programs from their accounts. The package provides the ability to determine which users are accessing and running specified programs along with their total level of usage.

Next-Gen 3: Sequencing, Modeling, and Advanced Biofuels - Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zengler, Karsten; Palsson, Bernhard; Lewis, Nathan

Successful, scalable implementation of biofuels is dependent on the efficient and near complete utilization of diverse biomass sources. One approach is to utilize the large recalcitrant biomass fraction (or any organic waste stream) through the thermochemical conversion of organic compounds to syngas, a mixture of carbon monoxide (CO), carbon dioxide (CO 2), and hydrogen (H 2), which can subsequently be metabolized by acetogenic microorganisms to produce next-gen biofuels. The goal of this proposal was to advance the development of the acetogen Clostridium ljungdahlii as a chassis organism for next-gen biofuel production from cheap, renewable sources and to detail the interconnectivitymore » of metabolism, energy conservation, and regulation of acetogens using next-gen sequencing and next-gen modeling. To achieve this goal we determined optimization of carbon and energy utilization through differential translational efficiency in C. ljungdahlii. Furthermore, we reconstructed a next-generation model of all major cellular processes, such as macromolecular synthesis and transcriptional regulation and deployed this model to predicting proteome allocation, overflow metabolism, and metal requirements in this model acetogen. In addition we explored the evolutionary significance of tRNA operon structure using the next-gen model and determined the optimal operon structure for bioproduction. Our study substantially enhanced the knowledgebaase for chemolithoautotrophs and their potential for advanced biofuel production. It provides next-generation modeling capability, offer innovative tools for genome-scale engineering, and provide novel methods to utilize next-generation models for the design of tunable systems that produce commodity chemicals from inexpensive sources.« less

Assessment of a simulated contraceptive prescribing activity for pharmacy students.

PubMed

Lynch, Sarah E; Griffin, Brooke L; Vest, Kathleen M

2018-02-01

The role of the pharmacist has been shifting rapidly. One example of change is the passage of legislation allowing pharmacists to independently initiate self-administered hormonal contraceptives in several states. There is no evidence of this specific topic being covered in pharmacy school curricula, and many states are requiring additional post-graduate training. This activity was designed to determine the utility of a contraceptive prescribing simulation activity for pharmacy students. Pharmacy students enrolled in a women's health elective learned about relevant state legislation and attended a clinical skills center simulation activity where they utilized an available prescribing algorithm. Students completed two scenarios and received grades based on their clinical decision-making and patient interaction skills. An electronic survey was distributed post-activity to assess student satisfaction and confidence when prescribing contraceptives. Responses and grades on the assignment were analyzed to determine the activity's utility. Students finished with median scores of 15, 14.8, and 14.5 out of 15 possible points for the three scenarios. Students reported overall satisfaction with the activity, with general agreement that the activity was realistic and made them feel like they were prepared to prescribe contraceptives. Independently initiating contraceptives is a novel practice area for pharmacists. This activity introduced students to the process of prescribing using realistic forms and scenarios. The utility of the activity was twofold - it introduced students to the changing environment of pharmacy practice and allowed students to apply their knowledge of contraceptives and women's health. Students performed well on the activity and reported high levels of satisfaction. Copyright © 2017 Elsevier Inc. All rights reserved.

Class-Wide Access to a Commercial Step 1 Question Bank During Preclinical Organ-Based Modules: A Pilot Project.

PubMed

Baños, James H; Pepin, Mark E; Van Wagoner, Nicholas

2018-03-01

The authors examined the usefulness of a commercially available Step 1 question bank as a formative academic support tool throughout organ-based modules in an integrated preclinical medical curriculum. The authors also determined the extent to which correlation between question bank utilization and academic metrics varied with Medical College Admission Test (MCAT) scores. In 2015, a cohort of 185 first-year medical students at University of Alabama School of Medicine were provided with 18-month full access to a commercially available Step 1 question bank of over 2,100 items throughout organ-based modules, although there were no requirements for use. Data on student use of the question bank were collected via an online administrative portal. Relationships between question bank utilization and academic outcomes including exams, module grades, and United States Medical Licensing Examination (USMLE) Step 1 were determined using multiple linear regression. MCAT scores and number of items attempted in the question bank significantly predicted all academic measures, with question bank utilization as the stronger predictor. The association between question bank utilization and academic outcome was stronger for individuals with lower MCAT scores. The findings elucidate a novel academic support mechanism that, for some programs, may help bridge the gap between holistic and mission-based admissions practices and a residency match process that places a premium on USMLE exam scores. Distributed formative use of USMLE Step 1 practice questions may be of value as an academic support tool that benefits all students, but particularly those entering with lower MCAT scores.

A methodology for the comparative evaluation of alternative bioseparation technologies.

PubMed

Tran, Richard; Zhou, Yuhong; Lacki, Karol M; Titchener-Hooker, Nigel J

2008-01-01

Advances in upstream technologies and growing commercial demand have led to cell culture processes of ever larger volumes and expressing at higher product titers. This has increased the burden on downstream processing. Concerns regarding the capacity limitations of packed-bed chromatography have led process engineers to begin investigating new bioseparation techniques that may be considered as "alternatives" to chromatography, and which could potentially offer higher processing capacities but at a lower cost. With the wide range of alternatives, which are currently available, each with their own strengths and inherent limitations, coupled with the time pressures associated with process development, the challenge for process engineers is to determine which technologies are most worth investigating. This article presents a methodology based on a multiattribute decision making (MADM) analysis approach, utilizing both quantitative and qualitative data, which can be used to determine the "industrial attractiveness" of bioseparation technologies, accounting for trade-offs between their strengths and weaknesses. By including packed-bed chromatography in the analysis as a reference point, it was possible to determine the alternatives, which show the most promise for use in large-scale manufacturing processes. The results of this analysis show that although the majority of alternative techniques offer certain advantages over conventional packed-bed chromatography, their attractiveness overall means that currently none of these technologies may be considered as viable alternatives to chromatography. The methodology introduced in this study may be used to gain significant quantitative insight as to the key areas in which improvements are required for each technique, and thus may be used as a tool to aid in further technological development.

Serotype determination of Salmonella by xTAG assay.

PubMed

Zheng, Zhibei; Zheng, Wei; Wang, Haoqiu; Pan, Jincao; Pu, Xiaoying

2017-10-01

Currently, no protocols or commercial kits are available to determine the serotypes of Salmonella by using Luminex MAGPIX®. In this study, an xTAG assay for serotype determination of Salmonella suitable for Luminex MAGPIX® is described and 228 Salmonella isolates were serotype determined by this xTAG assay. The xTAG assay consists of two steps: 1) Multiplex PCR to amplify simultaneously O, H and Vi antigen genes of Salmonella, and 2) Magplex-TAG™ microsphere hybridization to identify accurately the specific PCR products of different antigens. Compared with the serotyping results of traditional serum agglutination test, the sensitivity and specificity of the xTAG assay were 95.1% and 100%, respectively. The agreement rate of these two assays was 95.2%. Compared with Luminex xMAP® Salmonella Serotyping Assay (SSA) kit, the advantages of this xTAG assay are: First, the magnetic beads make it applicable to both the Luminex®100/200™ and MAGPIX® systems. Second, only primers rather than both primers and probes are needed in the xTAG assay, and the process of coupling antigen-specific oligonucleotide probes to beads is circumvented, which make the xTAG assay convenient to be utilized by other laboratories. The xTAG assay may serve as a rapid alternative or complementary method for traditional Salmonella serotyping tests, especially for laboratories that utilize the MAGPIX® systems. Copyright © 2017 Elsevier B.V. All rights reserved.

NTP comparison process

NASA Technical Reports Server (NTRS)

Corban, Robert

1993-01-01

The systems engineering process for the concept definition phase of the program involves requirements definition, system definition, and consistent concept definition. The requirements definition process involves obtaining a complete understanding of the system requirements based on customer needs, mission scenarios, and nuclear thermal propulsion (NTP) operating characteristics. A system functional analysis is performed to provide a comprehensive traceability and verification of top-level requirements down to detailed system specifications and provides significant insight into the measures of system effectiveness to be utilized in system evaluation. The second key element in the process is the definition of system concepts to meet the requirements. This part of the process involves engine system and reactor contractor teams to develop alternative NTP system concepts that can be evaluated against specific attributes, as well as a reference configuration against which to compare system benefits and merits. Quality function deployment (QFD), as an excellent tool within Total Quality Management (TQM) techniques, can provide the required structure and provide a link to the voice of the customer in establishing critical system qualities and their relationships. The third element of the process is the consistent performance comparison. The comparison process involves validating developed concept data and quantifying system merits through analysis, computer modeling, simulation, and rapid prototyping of the proposed high risk NTP subsystems. The maximum amount possible of quantitative data will be developed and/or validated to be utilized in the QFD evaluation matrix. If upon evaluation of a new concept or its associated subsystems determine to have substantial merit, those features will be incorporated into the reference configuration for subsequent system definition and comparison efforts.

42 CFR 484.215 - Initial establishment of the calculation of the national 60-day episode payment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... costs for the period. CMS determines the national mean cost per visit. (b) Determining HHA utilization... mean utilization for each of the six disciplines using home health claims data. (c) Use of the market... computing the national mean utilization for each discipline. (3) By multiplying the mean national cost per...

Staff Utilization and Commitment in Borno State Colleges of Education, Nigeria

ERIC Educational Resources Information Center

Fika, Ibrahim Baba; Ibi, Mustapha Baba; Abdulrahman, Aishatu

2016-01-01

The study determines the relationship between staff utilization and staff commitment in Borno State Colleges of Education, Nigeria. The objectives of the study were to determine: the level of staff utilization in Borno State Colleges of Education, the level of staff commitment in Borno State Colleges of Education and the relationship between staff…

Early colonization of functional groups of microbes in the infant gut.

PubMed

Pham, Van T; Lacroix, Christophe; Braegger, Christian P; Chassard, Christophe

2016-07-01

The colonization of the infant gut is crucial for early life development. Although the composition and diversity of the infant gut microbiota (GM) has been well described at a taxonomic level, functional aspects of this ecosystem remain unexplored. In the infant gut, lactate is produced by a number of bacteria and plays an important role in the trophic chain of the fermentation process. However, little is known about the lactate-utilizing bacteria (LUB) community in infants and their impact on gut health. By combining culture-based and molecular methods, we intensively studied LUB in fecal samples of 40 healthy infants on both taxonomic and functional levels. We demonstrated metabolic cross-feeding of lactate and identified keystone species specified for lactate utilization. The interactions of such species and their metabolic outcome could have direct impacts on infant health, either beneficial (production of short chain fatty acids) or detrimental (accumulation of hydrogen or hydrogen sulfide). We identified mode of delivery as a strong determinant for lactate-producing and -utilizing bacteria levels. These findings present the early establishment of GM with a novel perspective and emphasize the importance of lactate utilization in infancy. © 2016 Society for Applied Microbiology and John Wiley & Sons Ltd.

Ultrasensitive surveillance of sensors and processes

DOEpatents

Wegerich, Stephan W.; Jarman, Kristin K.; Gross, Kenneth C.

2001-01-01

A method and apparatus for monitoring a source of data for determining an operating state of a working system. The method includes determining a sensor (or source of data) arrangement associated with monitoring the source of data for a system, activating a method for performing a sequential probability ratio test if the data source includes a single data (sensor) source, activating a second method for performing a regression sequential possibility ratio testing procedure if the arrangement includes a pair of sensors (data sources) with signals which are linearly or non-linearly related; activating a third method for performing a bounded angle ratio test procedure if the sensor arrangement includes multiple sensors and utilizing at least one of the first, second and third methods to accumulate sensor signals and determining the operating state of the system.

Ultrasensitive surveillance of sensors and processes

DOEpatents

Wegerich, Stephan W.; Jarman, Kristin K.; Gross, Kenneth C.

1999-01-01

A method and apparatus for monitoring a source of data for determining an operating state of a working system. The method includes determining a sensor (or source of data) arrangement associated with monitoring the source of data for a system, activating a method for performing a sequential probability ratio test if the data source includes a single data (sensor) source, activating a second method for performing a regression sequential possibility ratio testing procedure if the arrangement includes a pair of sensors (data sources) with signals which are linearly or non-linearly related; activating a third method for performing a bounded angle ratio test procedure if the sensor arrangement includes multiple sensors and utilizing at least one of the first, second and third methods to accumulate sensor signals and determining the operating state of the system.

Activities of the Institute of Chemical Processing of Coal at Zabrze

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dreszer, K.

1995-12-31

The Institute of Chemical Processing of Coal at Zabrze was established in 1955. The works on carbochemical technologies have been, therefore, carried out at the Institute for 40 years. The targets of the Institute`s activities are research, scientific and developing works regarding a sensible utilization of fuels via their processing into more refined forms, safe environment, highly efficient use of energy carriers and technological products of special quality. The Institute of Chemical Processing of Coal has been dealing with the following: optimized use of home hard coals; improvement of classic coal coking technologies, processing and utilization of volatile coking products;more » production technologies of low emission rate fuels for communal management; analyses of coal processing technologies; new technologies aimed at increasing the efficiency of coal utilization for energy-generating purposes, especially in industry and studies on the ecological aspects of these processes; production technologies of sorbents and carbon activating agents and technologies of the utilization; rationalization of water and wastes management in the metallurgical and chemical industries in connection with removal of pollution especially dangerous to the environment from wastes; utilization technologies of refined materials (electrode cokes, binders, impregnating agents) for making electrodes, refractories and new generation construction carbon materials; production technologies of high quality bituminous and bituminous and resin coating, anti-corrosive and insulation materials; environmentally friendly utilization technologies for power station, mine and other wastes, and dedusting processes in industrial gas streams.« less

Improving surgeon utilization in an orthopedic department using simulation modeling

PubMed Central

Simwita, Yusta W; Helgheim, Berit I

2016-01-01

Purpose Worldwide more than two billion people lack appropriate access to surgical services due to mismatch between existing human resource and patient demands. Improving utilization of existing workforce capacity can reduce the existing gap between surgical demand and available workforce capacity. In this paper, the authors use discrete event simulation to explore the care process at an orthopedic department. Our main focus is improving utilization of surgeons while minimizing patient wait time. Methods The authors collaborated with orthopedic department personnel to map the current operations of orthopedic care process in order to identify factors that influence poor surgeons utilization and high patient waiting time. The authors used an observational approach to collect data. The developed model was validated by comparing the simulation output with the actual patient data that were collected from the studied orthopedic care process. The authors developed a proposal scenario to show how to improve surgeon utilization. Results The simulation results showed that if ancillary services could be performed before the start of clinic examination services, the orthopedic care process could be highly improved. That is, improved surgeon utilization and reduced patient waiting time. Simulation results demonstrate that with improved surgeon utilizations, up to 55% increase of future demand can be accommodated without patients reaching current waiting time at this clinic, thus, improving patient access to health care services. Conclusion This study shows how simulation modeling can be used to improve health care processes. This study was limited to a single care process; however the findings can be applied to improve other orthopedic care process with similar operational characteristics. PMID:29355193

Cascade heat recovery with coproduct gas production

DOEpatents

Brown, William R.; Cassano, Anthony A.; Dunbobbin, Brian R.; Rao, Pradip; Erickson, Donald C.

1986-01-01

A process for the integration of a chemical absorption separation of oxygen and nitrogen from air with a combustion process is set forth wherein excess temperature availability from the combustion process is more effectively utilized to desorb oxygen product from the absorbent and then the sensible heat and absorption reaction heat is further utilized to produce a high temperature process stream. The oxygen may be utilized to enrich the combustion process wherein the high temperature heat for desorption is conducted in a heat exchange preferably performed with a pressure differential of less than 10 atmospheres which provides considerable flexibility in the heat exchange.

Transformations of inorganic coal constituents in combustion systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helble, J.J.; Srinivasachar, S.; Wilemski, G.

1992-11-01

The inorganic constituents or ash contained in pulverized coal significantly increase the environmental and economic costs of coal utilization. For example, ash particles produced during combustion may deposit on heat transfer surfaces, decreasing heat transfer rates and increasing maintenance costs. The minimization of particulate emissions often requires the installation of cleanup devices such as electrostatic precipitators, also adding to the expense of coal utilization. Despite these costly problems, a comprehensive assessment of the ash formation and had never been attempted. At the start of this program, it was hypothesized that ash deposition and ash particle emissions both depended upon themore » size and chemical composition of individual ash particles. Questions such as: What determines the size of individual ash particles What determines their composition Whether or not particles deposit How combustion conditions, including reactor size, affect these processes remained to be answered. In this 6-year multidisciplinary study, these issues were addressed in detail. The ambitious overall goal was the development of a comprehensive model to predict the size and chemical composition distributions of ash produced during pulverized coal combustion. Results are described.« less

On the development of radiation tolerant surveillance camera from consumer-grade components

NASA Astrophysics Data System (ADS)

Klemen, Ambrožič; Luka, Snoj; Lars, Öhlin; Jan, Gunnarsson; Niklas, Barringer

2017-09-01

In this paper an overview on the process of designing a radiation tolerant surveillance camera from consumer grade components and commercially available particle shielding materials is given. This involves utilization of Monte-Carlo particle transport code MCNP6 and ENDF/B-VII.0 nuclear data libraries, as well as testing the physical electrical systems against γ radiation, utilizing JSI TRIGA mk. II fuel elements as a γ-ray sources. A new, aluminum, 20 cm × 20 cm × 30 cm irradiation facility with electrical power and signal wire guide-tube to the reactor platform, was designed and constructed and used for irradiation of large electronic and optical components assemblies with activated fuel elements. Electronic components to be used in the camera were tested against γ-radiation in an independent manner, to determine their radiation tolerance. Several camera designs were proposed and simulated using MCNP, to determine incident particle and dose attenuation factors. Data obtained from the measurements and MCNP simulations will be used to finalize the design of 3 surveillance camera models, with different radiation tolerances.

Agroecosystem development of industrial fermentation waste -- characterization of aroma-active compounds from the cultivation medium of Lactobacillus brevis.

PubMed

Ono, Toshirou; Usami, Atsushi; Nakaya, Satoshi; Shinpuku, Hideto; Yonejima, Yasunori; Ikeda, Atsushi; Miyazawa, Mitsuo

2015-01-01

Volatile oils obtained from both the liquid medium after incubation (MAI) and liquid medium before incubation (MBI) during the cultivation process of Lactobacillus brevis were isolated by hydrodistillation (HD) and analyzed to determine the utility of the liquid waste. The composition of the volatile oils was analyzed by capillary gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). In total, 55 and 36 compounds were detected in the volatile oils from MAI (MAI oil) and MBI (MBI oil), respectively. The principle components of MAI oil were N-containing compounds, including 2,3-dimethylpyrazine (16, 37.1 %), methylpyrazine (4, 17.1 %). The important aroma-active compounds in the oils were detected by GC-Olfactometry (GC-O), and their intensity of aroma were measured by aroma extract dilution analysis (AEDA). Expressly, pyrazine compounds were determined as key aroma components; in particular, 2,5-dimethylpyrazine and 2,3-dimethylpyrazine were the most primary aroma-active compound in MAI oil. These results imply that the waste medium after incubation of L. brevis may be utilized as a source of volatile oils.

Dual-Fuel Propulsion in Single-Stage Advanced Manned Launch System Vehicle

NASA Technical Reports Server (NTRS)

Lepsch, Roger A., Jr.; Stanley, Douglas O.; Unal, Resit

1995-01-01

As part of the United States Advanced Manned Launch System study to determine a follow-on, or complement, to the Space Shuttle, a reusable single-stage-to-orbit concept utilizing dual-fuel rocket propulsion has been examined. Several dual-fuel propulsion concepts were investigated. These include: a separate-engine concept combining Russian RD-170 kerosene-fueled engines with space shuttle main engine-derivative engines: the kerosene- and hydrogen-fueled Russian RD-701 engine; and a dual-fuel, dual-expander engine. Analysis to determine vehicle weight and size characteristics was performed using conceptual-level design techniques. A response-surface methodology for multidisciplinary design was utilized to optimize the dual-fuel vehicles with respect to several important propulsion-system and vehicle design parameters, in order to achieve minimum empty weight. The tools and methods employed in the analysis process are also summarized. In comparison with a reference hydrogen- fueled single-stage vehicle, results showed that the dual-fuel vehicles were from 10 to 30% lower in empty weight for the same payload capability, with the dual-expander engine types showing the greatest potential.

Immunoassay for wheat processing quality: utilization of a sandwich assay incorporating an immobilized single-chain fragment.

PubMed

Hill, A S; Giersch, T M; Loh, C S; Skerritt, J H

1999-10-01

A single-chain fragment (scFv) was engineered from a monoclonal antibody to high molecular weight glutenin subunits (HMW-GS), wheat flour polypeptides that play a major role in determining the mixing- and extension strength-related properties of dough and its subsequent baking performance. The scFv was expressed in a thioredoxin mutant Escherichia coli strain that allows disulfide bond formation in the cytoplasm and incorporated into a diagnostic test for wheat quality. Although the scFv lacks the more highly conserved antibody constant regions usually involved with immobilization, it was able to be directly immobilized to a polystyrene microwell solid phase without chemical or covalent modification of the protein or solid phase and utilized as a capture antibody in a double-antibody (two-site) immunoassay. In the sandwich assay, increasing HMW-GS concentrations produced increasing assay color, and highly significant correlations were obtained between optical densities obtained in the ELISA using the scFv and the content of large glutenin polymers in flours as well as measures of dough strength as measured by resistance to dough extension in rheological testing. The assay using the scFv was able to be carried out at lower flour sample extract dilutions than that required for a similar assay utilizing a monoclonal capture antibody. This research shows that engineered antibody fragments can be utilized to provide superior assay performance in two-site ELISAs over monoclonal antibodies and is the first application of an engineered antibody to the analysis of food processing quality.

Stimulation of glucose utilization and inhibition of protein glycation and AGE products by taurine.

PubMed

Nandhini, A T A; Thirunavukkarasu, V; Anuradha, C V

2004-07-01

Pathological effects of the process of non-enzymatic glycation of proteins are reflected in chronic complications of diabetes mellitus. We investigated the antiglycating effect of taurine in high fructose fed rats in vivo and the inhibiting potency of taurine in the process of in vitro glycation. Additionally, we investigated whether taurine enhances glucose utilization in the rat diaphragm. Rats fed a high fructose diet (60% total calories) were provided 2% taurine solution for 30 days. The effects of taurine on plasma glucose, fructosamine, protein glycation and glycosylated haemoglobin in high fructose rats were determined. For in vitro glycation a mixture of 25 mm glucose and 25 mm fructose was used as glycating agent, bovine serum albumin as the model protein and taurine as the inhibitor. Incubations were carried out in a constant temperature bath at 37 degrees C for 3-30 days. Amadori products and advanced glycation end products (AGEs) formed were measured. In vitro utilization of glucose was carried out in the rat diaphragm in the presence and absence of insulin in which taurine was used as an additive. The contents of glucose, glycated protein, glycosylated haemoglobin and fructosamine were significantly lowered by taurine treatment to high fructose rats. Taurine prevented in vitro glycation and the accumulation of AGEs. Furthermore, taurine enhanced glucose utilization in the rat diaphragm. This effect was additive to that of insulin and did not interfere with the action of insulin. These results underline the potential use of taurine as a therapeutic supplement for the prevention of diabetic pathology.

Single x-ray transmission system for bone mineral density determination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimenez-Mendoza, Daniel; Vargas-Vazquez, Damian; Espinosa-Arbelaez, Diego G.

2011-12-15

Bones are the support of the body. They are composed of many inorganic compounds and other organic materials that all together can be used to determine the mineral density of the bones. The bone mineral density is a measure index that is widely used as an indicator of the health of the bone. A typical manner to evaluate the quality of the bone is a densitometry study; a dual x-ray absorptiometry system based study that has been widely used to assess the mineral density of some animals' bones. However, despite the success stories of utilizing these systems in many differentmore » applications, it is a very expensive method that requires frequent calibration processes to work properly. Moreover, its usage in small species applications (e.g., rodents) has not been quite demonstrated yet. Following this argument, it is suggested that there is a need for an instrument that would perform such a task in a more reliable and economical manner. Therefore, in this paper we explore the possibility to develop a new, affordable, and reliable single x-ray absorptiometry system. The method consists of utilizing a single x-ray source, an x-ray image sensor, and a computer platform that all together, as a whole, will allow us to calculate the mineral density of the bone. Utilizing an x-ray transmission theory modified through a version of the Lambert-Beer law equation, a law that expresses the relationship among the energy absorbed, the thickness, and the absorption coefficient of the sample at the x-rays wavelength to calculate the mineral density of the bone can be advantageous. Having determined the parameter equation that defines the ratio of the pixels in radiographies and the bone mineral density [measured in mass per unit of area (g/cm{sup 2})], we demonstrated the utility of our novel methodology by calculating the mineral density of Wistar rats' femur bones.« less

Single x-ray transmission system for bone mineral density determination

NASA Astrophysics Data System (ADS)

Jimenez-Mendoza, Daniel; Espinosa-Arbelaez, Diego G.; Giraldo-Betancur, Astrid L.; Hernandez-Urbiola, Margarita I.; Vargas-Vazquez, Damian; Rodriguez-Garcia, Mario E.

2011-12-01

Bones are the support of the body. They are composed of many inorganic compounds and other organic materials that all together can be used to determine the mineral density of the bones. The bone mineral density is a measure index that is widely used as an indicator of the health of the bone. A typical manner to evaluate the quality of the bone is a densitometry study; a dual x-ray absorptiometry system based study that has been widely used to assess the mineral density of some animals' bones. However, despite the success stories of utilizing these systems in many different applications, it is a very expensive method that requires frequent calibration processes to work properly. Moreover, its usage in small species applications (e.g., rodents) has not been quite demonstrated yet. Following this argument, it is suggested that there is a need for an instrument that would perform such a task in a more reliable and economical manner. Therefore, in this paper we explore the possibility to develop a new, affordable, and reliable single x-ray absorptiometry system. The method consists of utilizing a single x-ray source, an x-ray image sensor, and a computer platform that all together, as a whole, will allow us to calculate the mineral density of the bone. Utilizing an x-ray transmission theory modified through a version of the Lambert-Beer law equation, a law that expresses the relationship among the energy absorbed, the thickness, and the absorption coefficient of the sample at the x-rays wavelength to calculate the mineral density of the bone can be advantageous. Having determined the parameter equation that defines the ratio of the pixels in radiographies and the bone mineral density [measured in mass per unit of area (g/cm2)], we demonstrated the utility of our novel methodology by calculating the mineral density of Wistar rats' femur bones.

To determine the end point of wet granulation by measuring powder energies and thermal properties.

PubMed

Dave, Rutesh H; Wu, Stephen H; Contractor, Labdhi D

2012-04-01

Wet granulation has been widely used in pharmaceutical industry as a tablet manufacturing process. However, end-point determination of wet granulation process has always remained a challenge. Many traditional methods are available for end-point determination, yet accuracy and reproducibility still remain a challenge. Microcrystalline cellulose, widely used as an excipient in pharmaceutical industry, was granulated using water. Wet mass was passed through sieve # 12 and dried till constant percentage loss on drying was obtained and dried granules were obtained. Wet and dried granules collected were subjected to basic flow energy, specific energy, bulk density, pressure drop, differential scanning calorimetry and effusivity measurements. Analysis of data revealed various stages of granule growth from initial seed formation by adding 200-400 g of water, granule growth was observed by adding 600-800 g of water and over wetting was observed at 1155 g of water. In this work, we have justified our work to properly identify and utilize this technique for practical purpose to correctly identify the end-point determination of microcrystalline cellulose and explain various principles underlying energies associated with powder and thermal measurements.

Potential for utilization of algal biomass for components of the diet in CELSS

NASA Technical Reports Server (NTRS)

Kamarei, A. R.; Nakhost, Z.; Karel, M.

1986-01-01

The major nutritional components of the green algae (Scenedesmus obliquus) grown in a Constant Cell Density Apparatus were determined. Suitable methodology to prepare proteins from which three major undesirable components of these cells (i.e., cell walls, nucleic acids, and pigments) were either removed or substantially reduced was developed. Results showed that processing of green algae to protein isolate enhances is potential nutritional and organoleptic acceptability as a diet component in controlled Ecological Life Support System.

A laboratory investigation of the variability of cloud reflected radiance fields

NASA Technical Reports Server (NTRS)

Mckee, T. B.; Cox, S. K.

1986-01-01

A method to determine the radiative properties of complex cloud fields was developed. A Cloud field optical simulator (CFOS) was constructed to simulate the interaction of cloud fields with visible radiation. The CFOS was verified by comparing experimental results from it with calculations performed with a Monte Carlo radiative transfer model. A software library was developed to process, reduce, and display CFOS data. The CFSOS was utilized to study the reflected radiane patterns from simulated cloud fields.

Documenting helicopter operations from an energy standpoint

NASA Technical Reports Server (NTRS)

Davis, S. J.; Stepniewski, W. Z.

1974-01-01

Results are presented of a study of the relative and absolute energy consumption of helicopters, including limited comparisons with fixed-wing aircraft, and selected surface transportation vehicles. Additional comparisons were made to determine the level of reduction in energy consumption expected from the application of advanced technologies to the helicopter design and sizing process. It was found that improvements in helicopter consumption characteristics can be accomplished through the utilization of advanced technology to reduce drag, structures weight, and powerplant fuel consumption.

A technique for correcting ERTS data for solar and atmospheric effects

NASA Technical Reports Server (NTRS)

Rogers, R. H.; Peacock, K.; Shah, N. J.

1974-01-01

A technique is described by which ERTS investigators can obtain and utilize solar and atmospheric parameters to transform spacecraft radiance measurements to absolute target reflectance signatures. A radiant power measuring instrument (RPMI) and its use in determining atmospheric paramaters needed for ground truth are discussed. The procedures used and results achieved in processing ERTS CCTs to correct for atmospheric parameters to obtain imagery are reviewed. Examples are given which demonstrate the nature and magnitude of atmospheric effects on computer classification programs.

The Utility of Personality Measures in the Admissions Process at the United States Naval Academy

DTIC Science & Technology

2002-06-01

ISFP, INFP, INTP , ESTP, ESFP, ENFP, ENTP, ESTJ, ESFJ, ENFJ , AND ENTJ. Within each pair of personality indicators a scale score is determined. Each...applicants if the reader is willing to make the assumption that the relationship between personality measures (MBTI & PHQ) and attrition is the same... relationship between them. 1. Tinto’s Student Integration Model Vincent Tinto’s work is accepted as the basis for the modern study of college attrition

Horse Hoof Protectors

NASA Technical Reports Server (NTRS)

2004-01-01

Power Pads, shown here, were designed to support and cushion horses' hooves while walking, rurning, and jumping, thus reducing the risk of injury. The pads utilize magnets implanted in the pads to increase blood circulation, not only reducing the chance of injury, but also speeding up the healing process if an injury does occur. Marshall Space Flight Center materials engineer Deborah Dianne Schmidt and materials technician Anthony Schaffer contributed to the design by providing fatigue stress analysis to the prototypes, thus helping determine the best configuration and maximum durability.

Benefit from NASA

NASA Image and Video Library

2004-04-15

Power Pads, shown here, were designed to support and cushion horses' hooves while walking, rurning, and jumping, thus reducing the risk of injury. The pads utilize magnets implanted in the pads to increase blood circulation, not only reducing the chance of injury, but also speeding up the healing process if an injury does occur. Marshall Space Flight Center materials engineer Deborah Dianne Schmidt and materials technician Anthony Schaffer contributed to the design by providing fatigue stress analysis to the prototypes, thus helping determine the best configuration and maximum durability.

Clean fuels from biomass

NASA Technical Reports Server (NTRS)

Hsu, Y.-Y.

1976-01-01

The paper discusses the U.S. resources to provide fuels from agricultural products, the present status of conversion technology of clean fuels from biomass, and a system study directed to determine the energy budget, and environmental and socioeconomic impacts. Conversion processes are discussed relative to pyrolysis and anaerobic fermentation. Pyrolysis breaks the cellulose molecules to smaller molecules under high temperature in the absence of oxygen, wheras anaerobic fermentation is used to convert biomass to methane by means of bacteria. Cost optimization and energy utilization are also discussed.

Utilization of cellulosic materials through enzyamtic hydrolysis. I. Fermentation of hydrolysate to ethanol and single-cell protein.

PubMed

Cysewski, G R; Wilke, C R

1976-09-01

Ethanol fermentation studies were conducted with Saccharomyces cerevisiae ATCC "4126, to determine the optimal conditions of oxygen tension and feed sugar concentration. In long-term continuous culture maximum ethanol production was found to occur at 0.07 mmHg oxygen tension and 10% glucose feed concentration. Preliminary process design and cost studies are developed for industrial scale fermentations to produce ethanol and torula yeast from sugars obtained by enzymatic hydrolysis of newsprint.

Spectrum/Orbit-Utilization Program

NASA Technical Reports Server (NTRS)

Miller, Edward F.; Sawitz, Paul; Zusman, Fred

1988-01-01

Interferences among geostationary satellites determine allocations. Spectrum/Orbit Utilization Program (SOUP) is analytical computer program for determining mutual interferences among geostationary-satellite communication systems operating in given scenario. Major computed outputs are carrier-to-interference ratios at receivers at specified stations on Earth. Information enables determination of acceptability of planned communication systems. Written in FORTRAN.

Design of Tomato Drying System by Utilizing Brine Geothermal

NASA Astrophysics Data System (ADS)

Afuar, W.; Sibarani, B.; Abdurrahman, G.; Hendrarsakti, J.

2016-09-01

Cultivation of tomato plants in Indonesia has been started since 1961.Tomatoes generally will rot in three days if left on storage. Moreover, low quality tomatoes have cheaper price. After harvested, tomatoes need to be treated by drying process so it can last longer. Energy for drying tomatoes can be obtained by utilizing heat from geothermal brine. Purpose of this research is to design a tomato drying system by extracting heat of geothermal brine from separator with certain flow rate to heat up water by using a heat exchanger. Furthermore, this water will be used to heat up the surrounding air which is circulated by blower system to heat up the tomatoes chamber. Tomatoes drying process needs temperature range of 50-70°C to evaporate water content from 95.7% to 26%. After that treatment, the tomatoes are expected to have better durability. The objective of this study is to determine the quantity of hot brine which is needed for drying tomatoes and to design a drying system so that tomatoes can last longer.

Optimizing the utility of military injury surveillance systems: a qualitative study within the Australian Defence Force.

PubMed

McKinnon, Adam D; Ozanne-Smith, Joan; Pope, Rodney

2009-05-01

Injury prevention guided by robust injury surveillance systems (ISS's) can effectively reduce military injury rates, but ISS's depend on human interaction. This study examined experiences and requirements of key users of the Australian Defence Force (ADF) ISS to determine whether the operation of the ISS was optimal, whether there were any shortcomings, and if so, how these shortcomings might be addressed. Semistructured interviews were conducted with 18 Australian Defence Department participants located throughout Australia. Grounded theory methods were used to analyze data by developing an understanding of processes and social phenomena related to injury surveillance systems within the military context. Interviews were recorded and professionally transcribed and information contained in the transcripts was analyzed using NVivo. Key themes relating to the components of an injury surveillance system were identified from the analysis. A range of processes and sociocultural factors influence the utility of military ISS's. These are discussed in detail and should be considered in the future design and operation of military ISS's to facilitate optimal outcomes for injury prevention.

The Concept and Experimental Investigation of CO2 and Steam Co-electrolysis for Resource Utilization in Space Exploration

NASA Technical Reports Server (NTRS)

Stoots, Carl; Mulloth, Lila M.; Luna, Bernadette; Varghese, Mini M.

2009-01-01

CO2 acquisition and utilization technologies will have a vital role in determining sustained and affordable life support and in-situ fuel production architectures for human and robotic exploration of Moon and Mars. For long-term human exploration to be practical, reliable technologies have to be implemented to capture and chemically reduce the metabolic CO2 from the cabin air to restitute oxygen consumption. Technologies that facilitate the in-situ capture and conversion of atmospheric CO2 to fuel are essential for a viable human mission to Mars and their demonstration on the moon is critical as well. This paper describes the concept and experimental investigation of a CO2 capture and reduction system that comprises an adsorption compressor and a CO2 and steam co-electrolysis unit. The process products include oxygen for life support and Syngas (CO and H2) for synthetic fuel production. Electrochemical performance in terms of CO2 conversion, oxygen production, and power consumption of a system with a capacity to process 1kg CO2 per day (1-person equivalent) will be discussed.

The role of shape recognition in figure/ground perception in infancy.

PubMed

White, Hannah; Jubran, Rachel; Heck, Alison; Chroust, Alyson; Bhatt, Ramesh S

2018-04-30

In this study we sought to determine whether infants, like adults, utilize previous experience to guide figure/ground processing. After familiarization to a shape, 5-month-olds preferentially attended to the side of an ambiguous figure/ground test stimulus corresponding to that shape, suggesting that they were viewing that portion as the figure. Infants' failure to exhibit this preference in a control condition in which both sides of the test stimulus were displayed as figures indicated that the results in the experimental condition were not due to a preference between two figure shapes. These findings demonstrate for the first time that figure/ground processing in infancy is sensitive to top-down influence. Thus, a critical aspect of figure/ground processing is functional early in life.

Conversion of Carbon Dioxide into Ethanol by Electrochemical Synthesis Method Using Cu-Zn Electrode

NASA Astrophysics Data System (ADS)

Riyanto; Ramadan, S.; Fariduddin, S.; Aminudin, A. R.; Hayatri, A. K.

2018-01-01

Research on conversion of carbon dioxide into ethanol has been done. The conversion process is carried out in a sodium bicarbonate electrolyte solution in an electrochemical synthesis reactor. As cathode was used Cu-Zn, while as anode carbon was utilized. Variations of voltage, concentration of sodium bicarbonate electrolyte solution and time of electrolysis were performed to determine the optimum conditions to convert carbon dioxide into ethanol. Sample of the electrochemical synthesis process was analyzed by gas chromatography. From the result, it is found that the optimum conditions of the electrochemical synthesis process of carbon dioxide conversion into ethanol are voltage, concentration of sodium bicarbonate electrolyte solution and time of electrolysis are 3 volts, 0.4 M and 90 minutes with the ethanol concentration of 10.44%.

Plasma gasification of municipal solid waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, G.W.; Tsangaris, A.V.

1995-12-31

Resorption Canada Limited (RCL) has conducted extensive operational testing with plasma technology in their plasma facility near Ottawa, Ontario, Canada to develop an environmentally friendly waste disposal process. Plasma technology, when utilized in a reactor vessel with the exclusion of oxygen, provides for the complete gasification of all combustibles in source materials with non-combustibles being converted to a non-hazardous slag. The energy and environmental characteristics of the plasma gasification of carbonaceous waste materials were studied over a period of eight years during which RCL completed extensive experimentation with MSW. A plasma processing system capable of processing 200--400 lbs/hr of MSWmore » was designed and built. The experimentation on MSW concentrated on establishing the optimum operating parameters and determining the energy and environmental characteristics at these operating parameters.« less

TRANSPORT PLANNING MODEL FOR WIDE AREA RECYCLING SYSTEM OF INDUSTRIAL WASTE PLASTIC

NASA Astrophysics Data System (ADS)

Arai, Yasuhiro; Kawamura, Hisashi; Koizumi, Akira; Mogi, Satoshi

To date, the majority of industrial waste plastic generated in an urban city has been processed into landfill. However, it is now necessary to actively utilize that plastic as a useful resource to create a recycling society with a low environment influence. In order to construct a reasonable recycling system, it is necessary to address the "transportation problem," which means determining how much industrial waste plastic is to be transported to what location. With the goal of eliminating landfill processing, this study considers a transport planning model for industrial waste plastic applying linear programming. The results of running optimized calculations under given scenarios clarified not only the possibilities for recycle processing in the Metropolitan area, but also the validity of wide area recycling system.

Recent progress in utilization planning for Space Station Freedom

NASA Technical Reports Server (NTRS)

Bartoe, John-David F.; Thiringer, Peter S.

1991-01-01

The progress made in utilization planning for the redesigned Space Station Freedom (SSF) concept is described. Consideration is given to the SSF user capabilities, the strategic planning process, the strategic planning organizations, and the Consolidated Operations and Utilization Plan (COUP, which will be released in January 1993) as well as to the COUP development process and implementation. The process by which the COUP will be produced was exercised in the international Multilateral Strategic and Tactical Integration Process (MUSTIP) simulation. The paper describes the MUSTIP simulation and its activities along with MUSTIP findings and recommendations.

Mechanistic modeling study on process optimization and precursor utilization with atmospheric spatial atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Zhang; He, Wenjie; Duan, Chenlong

2016-01-15

Spatial atomic layer deposition (SALD) is a promising technology with the aim of combining the advantages of excellent uniformity and conformity of temporal atomic layer deposition (ALD), and an industrial scalable and continuous process. In this manuscript, an experimental and numerical combined model of atmospheric SALD system is presented. To establish the connection between the process parameters and the growth efficiency, a quantitative model on reactant isolation, throughput, and precursor utilization is performed based on the separation gas flow rate, carrier gas flow rate, and precursor mass fraction. The simulation results based on this model show an inverse relation betweenmore » the precursor usage and the carrier gas flow rate. With the constant carrier gas flow, the relationship of precursor usage and precursor mass fraction follows monotonic function. The precursor concentration, regardless of gas velocity, is the determinant factor of the minimal residual time. The narrow gap between precursor injecting heads and the substrate surface in general SALD system leads to a low Péclet number. In this situation, the gas diffusion act as a leading role in the precursor transport in the small gap rather than the convection. Fluid kinetics from the numerical model is independent of the specific structure, which is instructive for the SALD geometry design as well as its process optimization.« less

Optical and Scratch Resistant Properties of Diamondlike Carbon Films Deposited with Single and Dual Ion Beams

NASA Technical Reports Server (NTRS)

Kussmaul, Michael T.; Bogdanski, Michael S.; Banks, Bruce A.; Mirtich, Michael J.

1993-01-01

Amorphous diamond-like carbon (DLC) films were deposited using both single and dual ion beam techniques utilizing filament and hollow cathode ion sources. Continuous DLC films up to 3000 A thick were deposited on fused quartz plates. Ion beam process parameters were varied in an effort to create hard, clear films. Total DLC film absorption over visible wavelengths was obtained using a Perkin-Elmer spectrophotometer. An ellipsometer, with an Ar-He laser (wavelength 6328 A) was used to determine index of refraction for the DLC films. Scratch resistance, frictional, and adherence properties were determined for select films. Applications for these films range from military to the ophthalmic industries.

Optical and scratch resistant properties of diamondlike carbon films deposited with single and dual ion beams

NASA Technical Reports Server (NTRS)

Kussmaul, Michael T.; Bogdanski, Michael S.; Banks, Bruce A.; Mirtich, Michael J.

1993-01-01

Amorphous diamondlike carbon (DLC) films were deposited using both single and dual ion beam techniques utilizing filament and hollow cathode ion sources. Continuous DLC films up to 3000 A thick were deposited on fused quartz plates. Ion beam process parameters were varied in an effort to create hard, clear films. Total DLC film absorption over visible wavelengths was obtained using a Perkin-Elmer spectrophotometer. An ellipsometer, with an Ar-He laser (wavelength 6328 A) was used to determine index of refraction for the DLC films. Scratch resistance and frictional and adherence properties were determined for select films. Applications for these films range from military to the ophthalmic industries.

Apparatus and method for measuring critical current properties of a coated conductor

DOEpatents

Mueller, Fred M [Los Alamos, NM; Haenisch, Jens [Dresden, DE

2012-07-24

The transverse critical-current uniformity in a superconducting tape was determined using a magnetic knife apparatus. A critical current I.sub.c distribution and transverse critical current density J.sub.c distribution in YBCO coated conductors was measured nondestructively with high resolution using a magnetic knife apparatus. The method utilizes the strong depression of J.sub.c in applied magnetic fields. A narrow region of low, including zero, magnetic field in a surrounding higher field is moved transversely across a sample of coated conductor. This reveals the critical current density distribution. A Fourier series inversion process was used to determine the transverse J.sub.c distribution in the sample.

The role of community health centers in assessing the social determinants of health for planning and policy: the example of frontier New Mexico.

PubMed

Bruna, Sean; Stone, Lisa Cacari; Wilger, Susan; Cantor, Jeremy; Guzman, Carolina

2014-01-01

This article examines the experience of a frontier-based community health center when it utilized the Tool for Health and Resilience in Vulnerable Environments (THRIVE) for assessing social determinants of health with a local health consortium. Community members (N = 357) rated safety, jobs, housing, and education among the top health issues. Community leaders integrated these health priorities in a countywide strategic planning process. This example of a frontier county in New Mexico demonstrates the critical role that community health centers play when engaging with local residents to assess community health needs for strategic planning and policy development.

Radial polar histogram: obstacle avoidance and path planning for robotic cognition and motion control

NASA Astrophysics Data System (ADS)

Wang, Po-Jen; Keyawa, Nicholas R.; Euler, Craig

2012-01-01

In order to achieve highly accurate motion control and path planning for a mobile robot, an obstacle avoidance algorithm that provided a desired instantaneous turning radius and velocity was generated. This type of obstacle avoidance algorithm, which has been implemented in California State University Northridge's Intelligent Ground Vehicle (IGV), is known as Radial Polar Histogram (RPH). The RPH algorithm utilizes raw data in the form of a polar histogram that is read from a Laser Range Finder (LRF) and a camera. A desired open block is determined from the raw data utilizing a navigational heading and an elliptical approximation. The left and right most radii are determined from the calculated edges of the open block and provide the range of possible radial paths the IGV can travel through. In addition, the calculated obstacle edge positions allow the IGV to recognize complex obstacle arrangements and to slow down accordingly. A radial path optimization function calculates the best radial path between the left and right most radii and is sent to motion control for speed determination. Overall, the RPH algorithm allows the IGV to autonomously travel at average speeds of 3mph while avoiding all obstacles, with a processing time of approximately 10ms.

An automated method of tuning an attitude estimator

NASA Technical Reports Server (NTRS)

Mason, Paul A. C.; Mook, D. Joseph

1995-01-01

Attitude determination is a major element of the operation and maintenance of a spacecraft. There are several existing methods of determining the attitude of a spacecraft. One of the most commonly used methods utilizes the Kalman filter to estimate the attitude of the spacecraft. Given an accurate model of a system and adequate observations, a Kalman filter can produce accurate estimates of the attitude. If the system model, filter parameters, or observations are inaccurate, the attitude estimates may be degraded. Therefore, it is advantageous to develop a method of automatically tuning the Kalman filter to produce the accurate estimates. In this paper, a three-axis attitude determination Kalman filter, which uses only magnetometer measurements, is developed and tested using real data. The appropriate filter parameters are found via the Process Noise Covariance Estimator (PNCE). The PNCE provides an optimal criterion for determining the best filter parameters.

ERBE Geographic Scene and Monthly Snow Data

NASA Technical Reports Server (NTRS)

Coleman, Lisa H.; Flug, Beth T.; Gupta, Shalini; Kizer, Edward A.; Robbins, John L.

1997-01-01

The Earth Radiation Budget Experiment (ERBE) is a multisatellite system designed to measure the Earth's radiation budget. The ERBE data processing system consists of several software packages or sub-systems, each designed to perform a particular task. The primary task of the Inversion Subsystem is to reduce satellite altitude radiances to fluxes at the top of the Earth's atmosphere. To accomplish this, angular distribution models (ADM's) are required. These ADM's are a function of viewing and solar geometry and of the scene type as determined by the ERBE scene identification algorithm which is a part of the Inversion Subsystem. The Inversion Subsystem utilizes 12 scene types which are determined by the ERBE scene identification algorithm. The scene type is found by combining the most probable cloud cover, which is determined statistically by the scene identification algorithm, with the underlying geographic scene type. This Contractor Report describes how the geographic scene type is determined on a monthly basis.

Critical Success Factor for Implementing Vocational Blended Learning

NASA Astrophysics Data System (ADS)

Dewi, K. C.; Ciptayani, P. I.; Surjono, H. D.; Priyanto

2018-01-01

Blended learning provides many benefits to the flexibility of time, place and situation constraints. The research’s objectives was describing the factors that determine the successful implementation of blended learning in vocational higher education. The research used a qualitative approach, data collected through observations and interviews by questionnare based on the CSFs indicators refers to TAM and Kliger. Data analysis was inductive method. The result provided an illustration that the success of vocational blended learning implementation was largely determined by the selection of instructional models that are inline with learning achievement target. The effectiveness of blended learning required the existence of policy support, readiness of IT infrastructure. Changing lecturer’s culture by utilizing ICT can also encourage the accelerated process of successful implementation. It can concluded that determinant factor of successful implementation of blended learning in vocational education is determined by teacher’s ability in mastering the pedagogical knowledge of designing instructional models.

Using Image Processing to Determine Emphysema Severity

NASA Astrophysics Data System (ADS)

McKenzie, Alexander; Sadun, Alberto

2010-10-01

Currently X-rays and computerized tomography (CT) scans are used to detect emphysema, but other tests are required to accurately quantify the amount of lung that has been affected by the disease. These images clearly show if a patient has emphysema, but are unable by visual scan alone, to quantify the degree of the disease, as it presents as subtle, dark spots on the lung. Our goal is to use these CT scans to accurately diagnose and determine emphysema severity levels in patients. This will be accomplished by performing several different analyses of CT scan images of several patients representing a wide range of severity of the disease. In addition to analyzing the original CT data, this process will convert the data to one and two bit images and will then examine the deviation from a normal distribution curve to determine skewness. Our preliminary results show that this method of assessment appears to be more accurate and robust than the currently utilized methods, which involve looking at percentages of radiodensities in the air passages of the lung.

Fuzzy adaptive interacting multiple model nonlinear filter for integrated navigation sensor fusion.

PubMed

Tseng, Chien-Hao; Chang, Chih-Wen; Jwo, Dah-Jing

2011-01-01

In this paper, the application of the fuzzy interacting multiple model unscented Kalman filter (FUZZY-IMMUKF) approach to integrated navigation processing for the maneuvering vehicle is presented. The unscented Kalman filter (UKF) employs a set of sigma points through deterministic sampling, such that a linearization process is not necessary, and therefore the errors caused by linearization as in the traditional extended Kalman filter (EKF) can be avoided. The nonlinear filters naturally suffer, to some extent, the same problem as the EKF for which the uncertainty of the process noise and measurement noise will degrade the performance. As a structural adaptation (model switching) mechanism, the interacting multiple model (IMM), which describes a set of switching models, can be utilized for determining the adequate value of process noise covariance. The fuzzy logic adaptive system (FLAS) is employed to determine the lower and upper bounds of the system noise through the fuzzy inference system (FIS). The resulting sensor fusion strategy can efficiently deal with the nonlinear problem for the vehicle navigation. The proposed FUZZY-IMMUKF algorithm shows remarkable improvement in the navigation estimation accuracy as compared to the relatively conventional approaches such as the UKF and IMMUKF.

Monitoring agricultural processing electrical energy use and efficiency

USDA-ARS?s Scientific Manuscript database

Energy costs have become proportionately larger as cotton post-harvest processing facilities have utilized other inputs more efficiently. A discrepancy in energy consumption per unit processed between facilities suggests that energy could be utilized more efficiently. Cotton gin facilities were in...

Simulation of the hyperspectral data from multispectral data using Python programming language

NASA Astrophysics Data System (ADS)

Tiwari, Varun; Kumar, Vinay; Pandey, Kamal; Ranade, Rigved; Agarwal, Shefali

2016-04-01

Multispectral remote sensing (MRS) sensors have proved their potential in acquiring and retrieving information of Land Use Land (LULC) Cover features in the past few decades. These MRS sensor generally acquire data within limited broad spectral bands i.e. ranging from 3 to 10 number of bands. The limited number of bands and broad spectral bandwidth in MRS sensors becomes a limitation in detailed LULC studies as it is not capable of distinguishing spectrally similar LULC features. On the counterpart, fascinating detailed information available in hyperspectral (HRS) data is spectrally over determined and able to distinguish spectrally similar material of the earth surface. But presently the availability of HRS sensors is limited. This is because of the requirement of sensitive detectors and large storage capability, which makes the acquisition and processing cumbersome and exorbitant. So, there arises a need to utilize the available MRS data for detailed LULC studies. Spectral reconstruction approach is one of the technique used for simulating hyperspectral data from available multispectral data. In the present study, spectral reconstruction approach is utilized for the simulation of hyperspectral data using EO-1 ALI multispectral data. The technique is implemented using python programming language which is open source in nature and possess support for advanced imaging processing libraries and utilities. Over all 70 bands have been simulated and validated using visual interpretation, statistical and classification approach.

Utilization of hydrotalcite modified with 3,4,5-trihydroxybenzoic acid for the treatment of silver-containing wastewater

NASA Astrophysics Data System (ADS)

Yanti, I.; Winata, W. F.; Anugrahwati, M.

2018-04-01

Utilization of hydrotalcite modified with 3,4,5-trihydroxybenzoic acid as a medium for the treatment of silver-containing wastewater has been done by using adsorption method. The modified hydrotalcite was prepared by direct precipitation using Mg and Al metals precursor and an organic compound of 3,4,5-trihydroxybenzoic acid. The modified material was then used for the treatment of silver-containing wastewater through adsorption method together with the determination of adsorption capacity, kinetics study as well as the material characterization after the treatment process. It could be observed from the results that the adsorption of silver onto the modified hydrotalcite was in accordance with Langmuir adsorption model with the adsorption capacity (qmax) of 400 mg.g-1. Moreover, the adsorption kinetics of the treatment showed that the process followed the kinetics model of pseudo-second-order of Ho with the velocity constant (k) of 1.15x10-4g.mg-1.minute-1. The adsorption process exhibited an exergonic property with the adsorption energy of 28.10x103 J.mol-1. All of the adsorption processes were conducted in the condition of pHadsorption = 3. Meanwhile, results from the characterization using FTIR showed the functional groups of C=C, -OH and NO3 - on the modified hydrotalcite underwent some alteration after the adsorption process of Ag(I). Therefore it can be observed that the functional groups of COOH and OH had an important role in the adsorption of silver from wastewater.

Optimum electric utility spot price determinations for small power producing facilities operating under PURPA provisions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghoudjehbaklou, H.; Puttgen, H.B.

This paper outlines an optimum spot price determination procedure in the general context of the Public Utility Regulatory Policies Act, PURPA, provisions. PURPA stipulates that local utilities must offer to purchase all available excess electric energy from Qualifying Facilities, QF, at fair market prices. As a direct consequence of these PURPA regulations, a growing number of owners are installing power producing facilities and optimize their operational schedules to minimize their utility related costs or, in some cases, actually maximize their revenues from energy sales to the local utility. In turn, the utility strives to use spot prices which maximize itsmore » revenues from any given Small Power Producing Facility, SPPF, a schedule while respecting the general regulatory and contractual framework. the proposed optimum spot price determination procedure fully models the SPPF operation, it enforces the contractual and regulatory restrictions, and it ensures the uniqueness of the optimum SPPF schedule.« less

Optimum electric utility spot price determinations for small power producing facilities operating under PURPA provisions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghoudjehbaklou, H.; Puttgen, H.B.

The present paper outlines an optimum spot price determination procedure in the general context of the Public Utility Regulatory Policies Act, PURPA, provisions. PURPA stipulates that local utilities must offer to purchase all available excess electric energy from Qualifying Facilities, QF, at fair market prices. As a direct consequence of these PURPA regulations, a growing number of owners are installing power producing facilities and optimize their operational schedules to minimize their utility related costs or, in some cases, actually maximize their revenues from energy sales to the local utility. In turn, the utility will strive to use spot prices whichmore » maximize its revenues from any given Small Power Producing Facility, SPPF, schedule while respecting the general regulatory and contractual framework. The proposed optimum spot price determination procedure fully models the SPPF operation, it enforces the contractual and regulatory restrictions, and it ensures the uniqueness of the optimum SPPF schedule.« less

Low cost fabrication development for oxide dispersion strengthened alloy vanes

NASA Technical Reports Server (NTRS)

Perkins, R. J.; Bailey, P. G.

1978-01-01

Viable processes were developed for secondary working of oxide dispersion strengthened (ODS) alloys to near-net shapes (NNS) for aircraft turbine vanes. These processes were shown capable of producing required microstructure and properties for vane applications. Material cost savings of 40 to 50% are projected for the NNS process over the current procedures which involve machining from rectangular bar. Additional machining cost savings are projected. Of three secondary working processes evaluated, directional forging and plate bending were determined to be viable NNS processes for ODS vanes. Directional forging was deemed most applicable to high pressure turbine (HPT) vanes with their large thickness variations while plate bending was determined to be most cost effective for low pressure turbine (LPT) vanes because of their limited thickness variations. Since the F101 LPT vane was selected for study in this program, development of plate bending was carried through to establishment of a preliminary process. Preparation of ODS alloy plate for bending was found to be a straight forward process using currently available bar stock, providing that the capability for reheating between roll passes is available. Advanced ODS-NiCrAl and ODS-FeCrAl alloys were utilized on this program. Workability of all alloys was adequate for directional forging and plate bending, but only the ODS-FeCrAl had adequate workability for shaped preform extrustion.

Chemical Processing of Non-Crop Plants for Jet Fuel Blends Production

NASA Technical Reports Server (NTRS)

Kulis, M. J.; Hepp, A. F.; McDowell, M.; Ribita, D.

2009-01-01

The use of Biofuels has been gaining in popularity over the past few years due to their ability to reduce the dependence on fossil fuels. Biofuels as a renewable energy source can be a viable option for sustaining long-term energy needs if they are managed efficiently. We describe our initial efforts to exploit algae, halophytes and other non-crop plants to produce synthetics for fuel blends that can potentially be used as fuels for aviation and non-aerospace applications. Our efforts have been dedicated to crafting efficient extraction and refining processes in order to extract constituents from the plant materials with the ultimate goal of determining the feasibility of producing biomass-based jet fuel from the refined extract. Two extraction methods have been developed based on communition processes, and liquid-solid extraction techniques. Refining procedures such as chlorophyll removal and transesterification of triglycerides have been performed. Gas chromatography in tandem with mass spectroscopy is currently being utilized in order to qualitatively determine the individual components of the refined extract. We also briefly discuss and compare alternative methods to extract fuel-blending agents from alternative biofuels sources.

Cold plasma processing of local planetary ores for oxygen and metallurgically important metals

NASA Technical Reports Server (NTRS)

Lynch, D. C.; Bullard, D.; Ortega, R.

1991-01-01

The utilization of a cold or nonequilibrium plasma in chlorination processing is discussed. Titanium dioxide (TiO2) was successfully chlorinated at temperatures between 700 and 900 C without the aid of carbon. In addition to these initial experiments, a technique was developed for determining the temperature of a specimen in a plasma. Development of that technique has required evaluating the emissivity of TiO2, ZrO2, and FeOTiO2 and analyzing the specimen temperature in a plasma as a function of both power absorbed by the plasma and the pressure of the plasma. The mass spectrometer was also calibrated with TiCl4 and CCl4 vapor.

Energy models and national energy policy

NASA Astrophysics Data System (ADS)

Bloyd, Cary N.; Streets, David G.; Fisher, Ronald E.

1990-01-01

As work begins on the development of a new National Energy Strategy (NES), the role of energy models is becoming increasingly important. Such models are needed to determine and assess both the short and long term effects of new policy initiatives on U.S. energy supply and demand. A central purpose of the model is to translate overall energy strategy goals into policy options while identifying potential costs and environmental benefits. Three models currently being utilized in the NES process are described, followed by a detailed listing of the publicly identified NES goals. These goals are then viewed in light of the basic modeling scenarios that were proposed as part of the NES development process.

A fiber optics system for monitoring utilization of ZnO adsorbent beds during desulfurization for logistic fuel cell applications

NASA Astrophysics Data System (ADS)

Sujan, Achintya; Yang, Hongyun; Dimick, Paul; Tatarchuk, Bruce J.

2016-05-01

An in-situ fiber optic based technique for direct measurement of capacity utilization of ZnO adsorbent beds by monitoring bed color changes during desulfurization for fuel cell systems is presented. Adsorbents composed of bulk metal oxides (ZnO) and supported metal oxides (ZnO/SiO2 and Cusbnd ZnO/SiO2) for H2S removal at 22 °C are examined. Adsorbent bed utilization at breakthrough is determined by the optical sensor as the maximum derivative of area under UV-vis spectrum from 250 to 800 nm observed as a function of service time. Since the response time of the sensor due to bed color change is close to bed breakthrough time, a series of probes along the bed predicts utilization of the portion of bed prior to H2S breakthrough. The efficacy of the optical sensor is evaluated as a function of inlet H2S concentration, H2S flow rate and desulfurization in presence of CO, CO2 and moisture in feed. A 6 mm optical probe is employed to measure utilization of a 3/16 inch ZnO extrudate bed for H2S removal. It is envisioned that with the application of the optical sensor, desulfurization can be carried out at high adsorbent utilization and low operational costs during on-board miniaturized fuel processing for logistic fuel cell power systems.

Facilitating factors and barriers to malaria research utilization for policy development in Malawi.

PubMed

Mwendera, Chikondi A; de Jager, Christiaan; Longwe, Herbert; Phiri, Kamija; Hongoro, Charles; Mutero, Clifford M

2016-10-19

Research on various determinants of health is key in providing evidence for policy development, thereby leading to successful interventions. Utilization of research is an intricate process requiring an understanding of contextual factors. The study was conducted to assess enhancing factors and barriers of research utilization for malaria policy development in Malawi. Qualitative research approach was used through in-depth interviews with 39 key informants that included malaria researchers, policy makers, programme managers, and key stakeholders. Purposive sampling and snowballing techniques were used in identifying key informants. Interview transcripts were entered in QSR Nvivo 11 software for coding and analysis. Respondents identified global efforts as key in advancing knowledge translation, while local political will has been conducive for research utilization. Other factors were availability of research, availability of diverse local researchers and stakeholders supporting knowledge translation. While barriers included: lack of platforms for researcher-public engagement, politics, researchers' lack of communication skills, lack of research collaborations, funder driven research, unknown World Health Organization policy position, and the lack of a malaria research repository. Overall, the study identified facilitating factors to malaria research utilization for policy development in Malawi. These factors need to be systematically coordinated to address the identified barriers and improve on malaria research utilization in policy development. Malaria research can be key in the implementation of evidence-based interventions to reduce the malaria burden and assist in the paradigm shift from malaria control to elimination in Malawi.

Cascade heat recovery with coproduct gas production

DOEpatents

Brown, W.R.; Cassano, A.A.; Dunbobbin, B.R.; Rao, P.; Erickson, D.C.

1986-10-14

A process for the integration of a chemical absorption separation of oxygen and nitrogen from air with a combustion process is set forth wherein excess temperature availability from the combustion process is more effectively utilized to desorb oxygen product from the absorbent and then the sensible heat and absorption reaction heat is further utilized to produce a high temperature process stream. The oxygen may be utilized to enrich the combustion process wherein the high temperature heat for desorption is conducted in a heat exchange preferably performed with a pressure differential of less than 10 atmospheres which provides considerable flexibility in the heat exchange. 4 figs.

A Study of Novice Systems Analysis Problem Solving Behaviors Using Protocol Analysis

DTIC Science & Technology

1992-09-01

conducted. Each subject was given the same task to perform. The task involved a case study (Appendix B) of a utility company’s customer order processing system...behavior (Ramesh, 1989). The task was to design a customer order processing system that utilized a centralized telephone answering service center...of the utility company’s customer order processing system that was developed based on information obtained by a large systems consulting firm during

Prioritizing Health: A Systematic Approach to Scoping Determinants in Health Impact Assessment.

PubMed

McCallum, Lindsay C; Ollson, Christopher A; Stefanovic, Ingrid L

2016-01-01

The determinants of health are those factors that have the potential to affect health, either positively or negatively, and include a range of personal, social, economic, and environmental factors. In the practice of health impact assessment (HIA), the stage at which the determinants of health are considered for inclusion is during the scoping step. The scoping step is intended to identify how the HIA will be carried out and to set the boundaries (e.g., temporal and geographical) for the assessment. There are several factors that can help to inform the scoping process, many of which are considered in existing HIA tools and guidance; however, a systematic method of prioritizing determinants was found to be lacking. In order to analyze existing HIA scoping tools that are available, a systematic literature review was conducted, including both primary and gray literature. A total of 10 HIA scoping tools met the inclusion/exclusion criteria and were carried forward for comparative analysis. The analysis focused on minimum elements and practice standards of HIA scoping that have been established in the field. The analysis determined that existing approaches lack a clear, systematic method of prioritization of health determinants for inclusion in HIA. This finding led to the development of a Systematic HIA Scoping tool that addressed this gap. The decision matrix tool uses factors, such as impact, public concern, and data availability, to prioritize health determinants. Additionally, the tool allows for identification of data gaps and provides a transparent method for budget allocation and assessment planning. In order to increase efficiency and improve utility, the tool was programed into Microsoft Excel. Future work in the area of HIA methodology development is vital to the ongoing success of the practice and utilization of HIA as a reliable decision-making tool.

Assessing chronic stroke survivors with aphasia sheds light on prevalence of spatial neglect

PubMed Central

Hreha, Kimberly; Mulry, Claire; Gross, Melissa; Jedziniak, Tarah; Gramas, Natanya; Ohevshalom, Leora; Sheridan, Alisha; Szabo, Gretchen; Davison, Christina; Barrett, A. M.

2016-01-01

Background Stroke is a chronic disease. Standardized assessment is essential in order to determine areas for treatment. Individuals with aphasia are often excluded from research, because it is believed that their language impairments may impact their ability to provide informed consent. Thus, right spatial neglect could be under-diagnosed. Objective This study was developed to (1) determine the frequency of spatial neglect in chronic left-brain stroke survivors with aphasia, (2) determine the clinical utility of an aphasia-friendly consent form, and (3) determine any differences between neglect and no-neglect groups regarding activities of daily living (ADL) performance and community independence. Methods Forty-six people were consented at community center. Three were screen failures secondary to the exclusion criteria. A novel, aphasia-friendly consent form was developed to facilitate participation of individuals with aphasia. This enabled 93% or 40 out of the 43 recruited participants to be included in this study. The Behavioral Inattention Test-conventional and the Catherine Bergego Scale via Kessler Foundation Neglect Assessment Process (CBS via KF-NAP) were utilized to determine neglect. The Life Space Questionnaire was used to determine community mobility and independence. The Barthel Index (BI) was used for objective clarification of performance in ADL. Results Successful use of the consent form resulted in determination that five out of 40 (12.5%) met criteria for spatial neglect; (on the CBS via KF-NAP). The neglect group had lower scores on the Life Space, suggesting less community mobility and independence, however, it was not statistically significant (p = 0.16). Differences in BI scores were also not significant (p = .013) but the neglect group did have reduced independence. Conclusions This study demonstrates the need to administer functional neglect assessments in left-brain stroke and to include individuals with aphasia in research. PMID:27322860

Assessing chronic stroke survivors with aphasia sheds light on prevalence of spatial neglect.

PubMed

Hreha, Kimberly; Mulry, Claire; Gross, Melissa; Jedziniak, Tarah; Gramas, Natanya; Ohevshalom, Leora; Sheridan, Alisha; Szabo, Gretchen; Davison, Christina; Barrett, A M

2017-03-01

Stroke is a chronic disease. Standardized assessment is essential in order to determine areas for treatment. Individuals with aphasia are often excluded from research, because it is believed that their language impairments may impact their ability to provide informed consent. Thus, right spatial neglect could be under-diagnosed. This study was developed to (1) determine the frequency of spatial neglect in chronic left-brain stroke survivors with aphasia, (2) determine the clinical utility of an aphasia-friendly consent form, and (3) determine any differences between neglect and no-neglect groups regarding activities of daily living (ADL) performance and community independence. Forty-six people were consented at community center. Three were screen failures secondary to the exclusion criteria. A novel, aphasia-friendly consent form was developed to facilitate participation of individuals with aphasia. This enabled 93% or 40 out of the 43 recruited participants to be included in this study. The Behavioral Inattention Test-conventional and the Catherine Bergego Scale via Kessler Foundation Neglect Assessment Process (CBS via KF-NAP) were utilized to determine neglect. The Life Space Questionnaire was used to determine community mobility and independence. The Barthel Index (BI) was used for objective clarification of performance in ADL. Successful use of the consent form resulted in determination that five out of 40 (12.5%) met criteria for spatial neglect; (on the CBS via KF-NAP). The neglect group had lower scores on the Life Space, suggesting less community mobility and independence, however, it was not statistically significant (p = 0.16). Differences in BI scores were also not significant (p = .013) but the neglect group did have reduced independence. This study demonstrates the need to administer functional neglect assessments in left-brain stroke and to include individuals with aphasia in research.

Smartphone and Mobile Application Utilization Prior to and Following Treatment Among Individuals Enrolled in Residential Substance Use Treatment

PubMed Central

Dahne, Jennifer; Lejuez, C. W.

2015-01-01

Background Following completion of substance use treatment, it is crucial for patients to continue to utilize skills learned in treatment for optimal treatment outcomes. Mobile applications (apps) on smartphones offer a unique platform to promote utilization of evidence-based skills following completion of substance use treatment. Despite the promise of mobile apps and smartphones for treatment delivery, it remains unknown whether patients in substance use treatment in the United States have access to smartphones and utilize mobile apps on smartphones. The present study sought to determine smartphone utilization among individuals enrolled in one residential substance use treatment center in the U.S catering specifically to low-income adults. Methods Participants included 251 individuals at a residential substance use treatment center in Washington DC admitted to the center between March, 2014 and January, 2015. During the intake process, participants completed interviewer-administered demographics and psychiatric questionnaires as well as a self-report of technology utilization. Results Results indicated that the majority of patients in this residential substance use treatment center owned mobile phones prior to treatment entry (86.9%) and expected to own mobile phones after leaving treatment (92.6%). Moreover, the majority of these phones were (68.5%) or will be smartphones (72.4%) on which patients reported utilizing mobile applications (Prior to treatment: 61.3%; Post treatment: 64.3%) and accessing the internet (Prior to treatment: 61.3%; Post treatment: 65.9%). Conclusions Mobile phone and smartphone ownership among this sample were comparable to ownership among U.S. adults broadly. Findings suggest that smartphones and mobile apps may hold clinical utility for fostering continued use of treatment skills following substance use treatment completion. PMID:26231698

Smartphone and Mobile Application Utilization Prior to and Following Treatment Among Individuals Enrolled in Residential Substance Use Treatment.

PubMed

Dahne, Jennifer; Lejuez, Carl W

2015-11-01

Following completion of substance use treatment, it is crucial for patients to continue to utilize skills learned in treatment for optimal treatment outcomes. Mobile applications (apps) on smartphones offer a unique platform to promote utilization of evidence-based skills following completion of substance use treatment. Despite the promise of mobile apps and smartphones for treatment delivery, it remains unknown whether patients in substance use treatment in the United States have access to smartphones and utilize mobile apps on smartphones. The present study sought to determine smartphone utilization among individuals enrolled in one residential substance use treatment center in the U.S. catering specifically to low-income adults. Participants included 251 individuals at a residential substance use treatment center in Washington DC admitted to the center between March, 2014 and January, 2015. During the intake process, participants completed interviewer-administered demographics and psychiatric questionnaires as well as a self-report of technology utilization. Results indicated that the majority of patients in this residential substance use treatment center owned mobile phones prior to treatment entry (86.9%) and expected to own mobile phones after leaving treatment (92.6%). Moreover, the majority of these phones were (68.5%) or will be smartphones (72.4%) on which patients reported utilizing mobile applications (prior to treatment: 61.3%; post treatment: 64.3%) and accessing the Internet (prior to treatment: 61.3%; post treatment: 65.9%). Mobile phone and smartphone ownership among this sample were comparable to ownership among U.S. adults broadly. Findings suggest that smartphones and mobile apps may hold clinical utility for fostering continued use of treatment skills following substance use treatment completion. Copyright © 2015 Elsevier Inc. All rights reserved.

Association of Inpatient Antimicrobial Utilization Measures with Antimicrobial Stewardship Activities and Facility Characteristics of Veterans Affairs Medical Centers.

PubMed

Graber, Christopher J; Jones, Makoto M; Chou, Ann F; Zhang, Yue; Goetz, Matthew Bidwell; Madaras-Kelly, Karl; Samore, Matthew H; Glassman, Peter A

2017-05-01

Antimicrobial stewardship programs (ASPs) have been advocated to improve antimicrobial utilization, but program implementation is variable. Antimicrobial stewardship programs (ASPs) have been advocated to improve antimicrobial utilization, but program implementation is variable. To determine associations between ASPs and facility characteristics, and inpatient antimicrobial utilization measures in the Veterans Affairs (VA) system in 2012. In 2012, VA administered a survey on antimicrobial stewardship practices to designated ASP contacts at VA acute care hospitals. From the survey, we identified 34 variables across 3 domains (evidence, organizational context, and facilitation) that were assessed using multivariable least absolute shrinkage and selection operator regression against 4 antimicrobial utilization measures from 2012: aggregate acute care antimicrobial use, antimicrobial use in patients with non-infectious primary discharge diagnoses, missed opportunities to convert from parenteral to oral antimicrobial therapy, and double anaerobic coverage. All 130 VA facilities with acute care services. Variables associated with at least 3 favorable changes in antimicrobial utilization included presence of postgraduate physician/pharmacy training programs, number of antimicrobial-specific order sets, frequency of systematic de-escalation review, presence of pharmacists and/or infectious diseases (ID) attendings on acute care ward teams, and formal ID training of the lead ASP pharmacist. Variables associated with 2 unfavorable measures included bed size, the level of engagement with VA Antimicrobial Stewardship Task Force online resources, and utilization of antimicrobial stop orders. Formalization of ASP processes and presence of pharmacy and ID expertise are associated with favorable utilization. Systematic de-escalation review and order set establishment may be high-yield interventions. Journal of Hospital Medicine 2017;12:301-309. © 2017 Society of Hospital Medicine

Process for converting cellulosic materials into fuels and chemicals

DOEpatents

Scott, Charles D.; Faison, Brendlyn D.; Davison, Brian H.; Woodward, Jonathan

1994-01-01

A process for converting cellulosic materials, such as waste paper, into fuels and chemicals utilizing enzymatic hydrolysis of the major constituent of paper, cellulose. A waste paper slurry is contacted by cellulase in an agitated hydrolyzer. The cellulase is produced from a continuous, columnar, fluidized-bed bioreactor utilizing immobilized microorganisms. An attritor and a cellobiase reactor are coupled to the agitated hydrolyzer to improve reaction efficiency. The cellulase is recycled by an adsorption process. The resulting crude sugars are converted to dilute product in a fluidized-bed bioreactor utilizing microorganisms. The dilute product is concentrated and purified by utilizing distillation and/or a biparticle fluidized-bed bioreactor system.

From instinct to evidence: the role of data in country decision-making in Chile.

PubMed

Aguilera, Ximena Paz; Espinosa-Marty, Consuelo; Castillo-Laborde, Carla; Gonzalez, Claudia

2016-01-01

The Chilean health system has undergone profound reforms since 1990, while going through many political upheavals, and faced demographic, health, and economic transformations. The full information requirements to develop an evidence-informed process implied the best possible use of available data, as well as efforts for improving the information systems. To examine, from a historical perspective, the use of data during the health reforms undertaken in Chile since 1990, and to identify the factors that have determined its utilization and improvement. A qualitative methodological approach was followed to review the case study of the Chilean experience with data on decision-making. We use as the primary source our first-hand experience as officials of the Ministry of Health (MOH) and the Ministry of Finance during the reform period considered. Second, a literature review was conducted, using documents from official sources, historical accounts, books, policy reports, and articles about the reform process, looking for the use of data. The Chilean health care reform process was intensive in utilization and production of information. In this context, the MOH conducted several studies, from the burden of disease, efficacy of interventions, cost-effectiveness, out-of-pocket payments, and fiscal impact to social preferences, among others. Policy and prioritization frameworks developed by international agencies influenced the use of data and the studies' agenda. Health systems in Latin America have struggled to adapt to changing health needs caused by demographic transition and economic growth. Health reforms in Chile provide lessons of this sustained effort, based on data and scientific grounds, with lights and shadows. Tradition, receptiveness to foreign ideas, and benchmarking with international data determined this approach, facilitated by the political influence of physicians and other technocrats. Besides, internationally comparable statistics are shown to play a significant role in policy debate.

Towards roll-to-roll manufacturing of polymer photonic devices

NASA Astrophysics Data System (ADS)

Subbaraman, Harish; Lin, Xiaohui; Ling, Tao; Guo, L. Jay; Chen, Ray T.

2014-03-01

Traditionally, polymer photonic devices are fabricated using clean-room processes such as photolithography, e-beam lithography, reactive ion etching (RIE) and lift-off methods etc, which leads to long fabrication time, low throughput and high cost. We have utilized a novel process for fabricating polymer photonic devices using a combination of imprinting and ink jet printing methods, which provides high throughput on a variety of rigid and flexible substrates with low cost. We discuss the manufacturing challenges that need to be overcome in order to realize true implementation of roll-to-roll manufacturing of flexible polymer photonic systems. Several metrology and instrumentation challenges involved such as availability of particulate-free high quality substrate, development and implementation of high-speed in-line and off-line inspection and diagnostic tools with adaptive control for patterned and unpatterned material films, development of reliable hardware, etc need to be addressed and overcome in order to realize a successful manufacturing process. Due to extreme resolution requirements compared to print media, the burden of software and hardware tools on the throughput also needs to be carefully determined. Moreover, the effect of web wander and variations in web speed need to accurately be determined in the design of the system hardware and software. In this paper, we show the realization of solutions for few challenges, and utilizing these solutions for developing a high-rate R2R dual stage ink-jet printer that can provide alignment accuracy of <10μm at a web speed of 5m/min. The development of a roll-to-roll manufacturing system for polymer photonic systems opens limitless possibilities for the deployment of high performance components in a variety of applications including communication, sensing, medicine, agriculture, energy, lighting etc.

Electron-beam lithography with character projection technique for high-throughput exposure with line-edge quality control

NASA Astrophysics Data System (ADS)

Ikeno, Rimon; Maruyama, Satoshi; Mita, Yoshio; Ikeda, Makoto; Asada, Kunihiro

2016-07-01

The high throughput of character projection (CP) electron-beam (EB) lithography makes it a promising technique for low-to-medium volume device fabrication with regularly arranged layouts, such as for standard-cell logics and memory arrays. However, non-VLSI applications such as MEMS and MOEMS may not be able to fully utilize the benefits of the CP method due to the wide variety of layout figures including curved and oblique edges. In addition, the stepwise shapes that appear because of the EB exposure process often result in intolerable edge roughness, which degrades device performances. In this study, we propose a general EB lithography methodology for such applications utilizing a combination of the CP and variable-shaped beam methods. In the process of layout data conversion with CP character instantiation, several control parameters were optimized to minimize the shot count, improve the edge quality, and enhance the overall device performance. We have demonstrated EB shot reduction and edge-quality improvement with our methodology by using a leading-edge EB exposure tool, ADVANTEST F7000S-VD02, and a high-resolution hydrogen silsesquioxane resist. Atomic force microscope observations were used to analyze the resist edge profiles' quality to determine the influence of the control parameters used in the data conversion process.

Measuring horizontal integration among health care providers in the community: an examination of a collaborative process within a palliative care network.

PubMed

Bainbridge, Daryl; Brazil, Kevin; Krueger, Paul; Ploeg, Jenny; Taniguchi, Alan; Darnay, Julie

2015-05-01

In many countries formal or informal palliative care networks (PCNs) have evolved to better integrate community-based services for individuals with a life-limiting illness. We conducted a cross-sectional survey using a customized tool to determine the perceptions of the processes of palliative care delivery reflective of horizontal integration from the perspective of nurses, physicians and allied health professionals working in a PCN, as well as to assess the utility of this tool. The process elements examined were part of a conceptual framework for evaluating integration of a system of care and centred on interprofessional collaboration. We used the Index of Interdisciplinary Collaboration (IIC) as a basis of measurement. The 86 respondents (85% response rate) placed high value on working collaboratively and most reported being part of an interprofessional team. The survey tool showed utility in identifying strengths and gaps in integration across the network and in detecting variability in some factors according to respondent agency affiliation and profession. Specifically, support for interprofessional communication and evaluative activities were viewed as insufficient. Impediments to these aspects of horizontal integration may be reflective of workload constraints, differences in agency operations or an absence of key structural features.

Application of the Materials-by-Design Methodology to Redesign a New Grade of the High-Strength Low-Alloy Class of Steels with Improved Mechanical Properties and Processability

NASA Astrophysics Data System (ADS)

Grujicic, M.; Snipes, J. S.; Ramaswami, S.

2016-01-01

An alternative to the traditional trial-and-error empirical approach for the development of new materials is the so-called materials-by-design approach. Within the latter approach, a material is treated as a complex system and its design and optimization is carried out by employing computer-aided engineering analyses, predictive tools, and available material databases. In the present work, the materials-by-design approach is utilized to redesign a grade of high-strength low-alloy (HSLA) class of steels with improved mechanical properties (primarily strength and fracture toughness), processability (e.g., castability, hot formability, and weldability), and corrosion resistance. Toward that end, a number of material thermodynamics, kinetics of phase transformations, and physics of deformation and fracture computational models and databases have been developed/assembled and utilized within a multi-disciplinary, two-level material-by-design optimization scheme. To validate the models, their prediction is compared against the experimental results for the related steel HSLA100. Then the optimization procedure is employed to determine the optimal chemical composition and the tempering schedule for a newly designed grade of the HSLA class of steels with enhanced mechanical properties, processability, and corrosion resistance.

Use of a Closed-Loop Tracking Algorithm for Orientation Bias Determination of an S-Band Ground Station

NASA Technical Reports Server (NTRS)

Welch, Bryan W.; Piasecki, Marie T.; Schrage, Dean S.

2015-01-01

The Space Communications and Navigation (SCaN) Testbed project completed installation and checkout testing of a new S-Band ground station at the NASA Glenn Research Center in Cleveland, Ohio in 2015. As with all ground stations, a key alignment process must be conducted to obtain offset angles in azimuth (AZ) and elevation (EL). In telescopes with AZ-EL gimbals, this is normally done with a two-star alignment process, where telescope-based pointing vectors are derived from catalogued locations with the AZ-EL bias angles derived from the pointing vector difference. For an antenna, the process is complicated without an optical asset. For the present study, the solution was to utilize the gimbal control algorithms closed-loop tracking capability to acquire the peak received power signal automatically from two distinct NASA Tracking and Data Relay Satellite (TDRS) spacecraft, without a human making the pointing adjustments. Briefly, the TDRS satellite acts as a simulated optical source and the alignment process proceeds exactly the same way as a one-star alignment. The data reduction process, which will be discussed in the paper, results in two bias angles which are retained for future pointing determination. Finally, the paper compares the test results and provides lessons learned from the activity.

Kramers problem in evolutionary strategies

NASA Astrophysics Data System (ADS)

Dunkel, J.; Ebeling, W.; Schimansky-Geier, L.; Hänggi, P.

2003-06-01

We calculate the escape rates of different dynamical processes for the case of a one-dimensional symmetric double-well potential. In particular, we compare the escape rates of a Smoluchowski process, i.e., a corresponding overdamped Brownian motion dynamics in a metastable potential landscape, with the escape rates obtained for a biologically motivated model known as the Fisher-Eigen process. The main difference between the two models is that the dynamics of the Smoluchowski process is determined by local quantities, whereas the Fisher-Eigen process is based on a global coupling (nonlocal interaction). If considered in the context of numerical optimization algorithms, both processes can be interpreted as archetypes of physically or biologically inspired evolutionary strategies. In this sense, the results discussed in this work are utile in order to evaluate the efficiency of such strategies with regard to the problem of surmounting various barriers. We find that a combination of both scenarios, starting with the Fisher-Eigen strategy, provides a most effective evolutionary strategy.